Powered by Deep Web Technologies
Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Variable Speed Drive Volumetric Tracking (VSDVT) for Airflow Control in Variable Air Volume (VAV) Systems  

E-Print Network (OSTI)

An airflow control method has been developed for variable air volume (VAV) systems. This airflow control method is named VSD volumetric tracking (VSDVT) since both the supply and return airflows are determined using signals of the variable speed drives (VSD) instead of the flow stations. Its performance is studied and compared with the fan tracking (FT) method using model simulations. The VSDVT maintains a constant building pressure and the required outside airflow under all load conditions, reduces the annual return air fan energy by up to 50%, and the annual supply air fan energy by up to 30%. This paper presents the VSDVT method, the system models, and the simulation results.

Liu, M.

2002-01-01T23:59:59.000Z

2

Energy Savings for Occupancy-Based Control (OBC) of Variable-Air-Volume (VAV) Systems  

SciTech Connect

This study evaluates the savings potential of occupancy based control (OBC) for large office buildings with VAV terminal boxes installed.

Zhang, Jian; Lutes, Robert G.; Liu, Guopeng; Brambley, Michael R.

2013-01-24T23:59:59.000Z

3

Duct Leakage Impacts on VAV System Performance in Large Commercial  

NLE Websites -- All DOE Office Websites (Extended Search)

Duct Leakage Impacts on VAV System Performance in Large Commercial Duct Leakage Impacts on VAV System Performance in Large Commercial Buildings Title Duct Leakage Impacts on VAV System Performance in Large Commercial Buildings Publication Type Report LBNL Report Number LBNL-53605 Year of Publication 2003 Authors Wray, Craig P., and Nance Matson Abstract The purpose of this study is to evaluate the variability of duct leakage impacts on air distribution system performance for typical large commercial buildings in California. Specifically, a hybrid DOE-2/TRNSYS sequential simulation approach was used to model the energy use of a low-pressure terminal-reheat variable-air-volume (VAV) HVAC system with six duct leakage configurations (tight to leaky) in nine prototypical large office buildings (representing three construction eras in three California climates where these types of buildings are common). Combined fan power for the variable-speed-controlled supply and return fans at design conditions was assumed to be 0.8 W/cfm. The VAV system that we simulated had perfectly insulated ducts, and maintained constant static pressure in the ducts upstream of the VAV boxes and a constant supply air temperature at the air-handler. Further evaluations of duct leakage impacts should be carried out in the future after methodologies are developed to deal with duct surface heat transfer effects, to deal with airflows entering VAV boxes from ceiling return plenums (e.g., to model parallel fan-powered VAV boxes), and to deal with static pressure reset and supply air temperature reset strategies.

4

Commissioning and Diagnosis of VAV Air-Conditioning Systems  

E-Print Network (OSTI)

This paper presents a fault detection and diagnosis (FDD) strategy based on system knowledge, qualitative states and object-oriented statistical process control (SPC) models for typical pressure-independent variable air volume (VAV) air-conditioning systems. Eight FDD schemes are built to detect the eleven pre-defined VAV faults using the qualitative and quantitative FDD approaches within the strategy at two steps. The ten hard faults, which would affect the system operation, are analyzed at Step 1. The soft fault, which would not affect the basic system operation but would impact the supervisory controls, is analyzed at Step 2. The strategy is tested and validated on typical VAV systems involving multiple faults, both in simulation and in-situ tests. A software package is developed as a BMS-assisted automatic commissioning tool based on the FDD strategy. Off-line tests were conducted in both the simulated building and the real building.

Qin, J.; Wang, S.; Chan, C.; Xiao, F.

2006-01-01T23:59:59.000Z

5

Analysis of the Energy Consumption of VAV System in Different Supply Air Control Strategies  

Science Conference Proceedings (OSTI)

Variable air volume (VAV) system has been widely applied due to its characteristics of eminent energy saving and thermal comfort. Because of its above characteristics, sophisticated automatic control systems are required to support its operation. While ... Keywords: VAV A/C system, supply air control strategy, energy consumption analysis

Junjie Guo, Xiangxin Cheng

2012-07-01T23:59:59.000Z

6

Final Project Report: Self-Correcting Controls for VAV System Faults Filter/Fan/Coil and VAV Box Sections  

SciTech Connect

This report addresses original research by the Pacific Northwest National Laboratory for the California Institute for Energy and Environment on self-correcting controls for variable-air-volume (VAV) heating, ventilating and air-conditioning systems and focuses specifically on air handling and VAV box components of the air side of the system. A complete set of faults for these components was compiled and a fault mode analysis performed to understand the detectable symptoms of the faults and the chain of causation. A set of 26 algorithms was developed to facilitate the automatic correction of these faults in typical commercial VAV systems. These algorithms include training tests that are used during commissioning to develop models of normal system operation, passive diagnostics used to detect the symptoms of faults, proactive diagnostics used to diagnose the cause of a fault, and finally fault correction algorithms. Ten of the twenty six algorithms were implemented in a prototype software package that interfaces with a test bed facility at PNNL's Richland, WA, laboratory. Measurement bias faults were instigated in the supply-air temperature sensor and the supply-air flow meter to test the algorithms developed. The algorithms as implemented in the laboratory software correctly detected, diagnosed and corrected these faults. Finally, an economic and impact assessment was performed for the State of California for deployment of self-correcting controls. Assuming 15% HVAC energy savings and a modeled deployment profile, 3.1-5.8 TBu of energy savings are possible by year 15.

Brambley, Michael R.; Fernandez, Nicholas; Wang, Weimin; Cort, Katherine A.; Cho, Heejin; Ngo, Hung; Goddard, James K.

2011-05-01T23:59:59.000Z

7

Automatic Commissioning of Multiple VAV Terminals  

E-Print Network (OSTI)

A site survey on a modern operating commercial building screened 261 ineffective VAV (Variable Air Volume) boxes (20.9% of the total boxes in the building) and summarized ten typical faults for VAV air-conditioning system(s) resulting in energy waste, performance degradation or totally out of control. A strategy is developed to automatically check the health condition of VAV terminals and diagnose the faults. Hybrid approach is employed to establish a commissioning and re-commissioning tool of VAV air-conditioning system. Performance indices with expert rules based on system physical characteristics are adopted to detect and diagnose the nine of the ten faults. PCA (Principal Component Analysis) method is developed to detect and diagnose the VAV box flow sensor bias (Fault 10) and to reconstruct the faulty sensors. A multiple VAV fault FDD strategy for a VAV entire system is developed, which is validated in simulation and filed tests.

Qin, J.; Wang, S.

2004-01-01T23:59:59.000Z

8

Duct leakage impacts on VAV system performance in California large commercial buildings  

SciTech Connect

The purpose of this study is to evaluate the variability of duct leakage impacts on air distribution system performance for typical large commercial buildings in California. Specifically, a hybrid DOE-2/TRNSYS sequential simulation approach was used to model the energy use of a low-pressure terminal-reheat variable-air-volume (VAV) HVAC system with six duct leakage configurations (tight to leaky) in nine prototypical large office buildings (representing three construction eras in three California climates where these types of buildings are common). Combined fan power for the variable-speed-controlled supply and return fans at design conditions was assumed to be 0.8 W/cfm. Based on our analyses of the 54 simulation cases, the increase in annual fan energy is estimated to be 40 to 50% for a system with a total leakage of 19% at design conditions compared to a tight system with 5% leakage. Annual cooling plant energy also increases by about 7 to 10%, but reheat energy decreases (about 3 to 10%). In combination, the increase in total annual HVAC site energy is 2 to 14%. The total HVAC site energy use includes supply and return fan electricity consumption, chiller and cooling tower electricity consumption, boiler electricity consumption, and boiler natural gas consumption. Using year 2000 average commercial sector energy prices for California ($0.0986/kWh and $7.71/Million Btu), the energy increases result in 9 to 18% ($7,400 to $9,500) increases in HVAC system annual operating costs. Normalized by duct surface area, the increases in annual operating costs are 0.14 to 0.18 $/ft{sup 2}. Using a suggested one-time duct sealing cost of $0.20 per square foot of duct surface area, these results indicate that sealing leaky ducts in VAV systems has a simple payback period of about 1.3 years. Even with total leakage rates as low as 10%, duct sealing is still cost effective. This suggests that duct sealing should be considered at least for VAV systems with 10% or more total duct leakage. The VAV system that we simulated had perfectly insulated ducts, and maintained constant static pressure in the ducts upstream of the VAV boxes and a constant supply air temperature at the airhandler. Further evaluations of duct leakage impacts should be carried out in the future after methodologies are developed to deal with duct surface heat transfer effects, to deal with airflows entering VAV boxes from ceiling return plenums (e.g., to model parallel fan-powered VAV boxes), and to deal with static pressure reset and supply air temperature reset strategies.

Wray, Craig P.; Matson, Nance E.

2003-10-01T23:59:59.000Z

9

The Optimization of Control Parameters for VAV HVAC System Commissioning  

E-Print Network (OSTI)

One of the technical subjects in commissioning for HVAC system is to enhance control performance and time efficiency, while the tuning of the optimal parameters to control HVAC system takes much time and labor in particular. Therefore, we propose a kind of commissioning technique as follows. We identified the dynamic characteristics of components of an actual VAV HVAC system such as rooms, VAV dampers, two way valves and chilled water coils, and verified the behaviors of the models and choose the optimal control parameters on a personal computer. Then adopting them for the actual system, we verified the control performance. Through the procedure, we showed the possibility of off-site and off-line control parameter tuning to reduce the cost and time at on-site and in on-line using the measured data in a real HVAC system.

Song, S.; Maehara, K.; Sagara, N.

2006-01-01T23:59:59.000Z

10

Theoretical Study of a Novel Control Method of VAV Air-conditioning System Based on MATLAB  

E-Print Network (OSTI)

The main purpose of this study is to put forward a novel nonlinear feedback control strategy on controlling indoor air temperature by variable air volume. A dynamic model of a typical room for a VAV air-conditioning system is established. The performance of the novel control strategy is investigated. Simulation of the controlling air temperature, on which the novel strategy is adopted, was carried out based on MATLAB in the VAV system. In order to show that the novel control strategy outperforms conventional PID control, a comparison is made between the performance of conventional PID and the novel nonlinear feedback control strategy. The results show that nonlinear feedback control strategy outperforms a conventional PID control system in terms of celerity, stability and other aspects.

Shi, Z.; Hu, S.; Wang, G.; Li, A.

2006-01-01T23:59:59.000Z

11

Determining Critical Pressure and Duct Leakage in VAV Air-Handling...  

NLE Websites -- All DOE Office Websites (Extended Search)

for moving air in buildings use a significant amount of energy. It is well known that fan energy use in variable-air-volume (VAV) systems can be reduced by resetting the supply...

12

Analysis of the Potential Energy Savings for 14 Office Buildings with VAV Systems  

E-Print Network (OSTI)

At the beginning of an existing building commissioning (EBCx)/energy retrofit project, some form of screening is usually applied to determine whether there is sufficient potential for savings to justify a formal EBCx assessment/energy audit. In this study, an improved methodology for potential energy savings estimation from EBCx/retrofit measures, based on Baltazar's methodology (2006), is proposed to perform this type of screening. The improvements are included on optimization parameters, space load calculation, simulation of buildings with multiple types of HVAC systems, AHU shutdown simulation, among others. The improved methodology was used to estimate annual potential energy cost savings for 14 office buildings in Austin, TX with either single duct VAV (SDVAV) systems or dual duct VAV (DDVAV) systems. The estimates are based on very limited information about the buildings and the built-in HVAC systems as well as one year of utility bills. From this analysis, the methodology has predicted an average total potential savings of 36% for SDVAV systems with electric terminal reheat, 22% for SDVAV systems with hot water reheat, and 25% for DDVAV systems. To validate these results, the estimated potential savings are compared with savings proposed in respective EBCx assessment reports. Based on the comparison of the report estimates and the potential savings with the improved methodology, it was found that 'generalized' factors of assessment predicted energy cost savings to estimated potential energy cost savings could be found. The factors identified in these cases were 0.68, 0.66, and 0.61 for each type of system - SDVAV w/electric reheat, SDVAV w/hot water reheat, and DDVAV, respectively.

Claridge, D. E.; Liu, J.; Baltazar, J. C.

2010-01-01T23:59:59.000Z

13

Determining Critical Pressure and Duct Leakage in VAV Air-Handling Units  

NLE Websites -- All DOE Office Websites (Extended Search)

Determining Critical Pressure and Duct Leakage in VAV Air-Handling Units Determining Critical Pressure and Duct Leakage in VAV Air-Handling Units Speaker(s): Clifford Federspiel Date: December 3, 2003 - 12:00pm Location: Bldg. 90 Seminar Host/Point of Contact: Nance Matson Fans for moving air in buildings use a significant amount of energy. It is well known that fan energy use in variable-air-volume (VAV) systems can be reduced by resetting the supply duct pressure. The standard way to reset duct pressure is by controlling the most-open terminal damper to a nearly open position. Most systems can't measure terminal damper positions, so pressures are either not reset at all or use ad hoc resetting strategies that are configured sub-optimally. In this seminar I will describe a new method of determining the critical supply duct pressure for VAV systems.

14

Field testing of component-level model-based fault detection methods for mixing boxes and VAV fan systems  

SciTech Connect

An automated fault detection and diagnosis tool for HVAC systems is being developed, based on an integrated, life-cycle, approach to commissioning and performance monitoring. The tool uses component-level HVAC equipment models implemented in the SPARK equation-based simulation environment. The models are configured using design information and component manufacturers' data and then fine-tuned to match the actual performance of the equipment by using data measured during functional tests of the sort using in commissioning. This paper presents the results of field tests of mixing box and VAV fan system models in an experimental facility and a commercial office building. The models were found to be capable of representing the performance of correctly operating mixing box and VAV fan systems and detecting several types of incorrect operation.

Xu, Peng; Haves, Philip

2002-05-16T23:59:59.000Z

15

Impacts of Static Pressure Reset on VAV System Air Leakage, Fan Power and Thermal Energy - Part I: Theoretical Model and Simulation  

E-Print Network (OSTI)

As for a variable air volume (VAV) system, the air duct static pressure is a typical control variable maintained by modulating supply fan speed. The static pressure equals to the summation of the duct pressure loss downstream of the sensor to the terminal box and box inlet static pressure. Typically, the air duct static pressure is set as a constant set point based on the system design information and sensor location. However, under partial load conditions, the terminal box dampers have to be closed more since either required airflow is less than the design airflow which directly leads to much less pressure loss. Thus the static pressure set point should be reset lower in order to reduce fan power, avoid noise at terminal box dampers and box damper malfunction due to excessive pressure. Different static pressure reset schedules are reviewed and compared, considering the influence of outside air temperature on the building load, availability of the VAV box damper positions, the airflow ratio based static pressure reset has also applicable advantages over the existing constant static pressure set point and two typical reset methods. This paper present the theoretical models to express the impacts of static pressure reset on fan airflow, fan head, air leakage, fan power and thermal energy for both pressure independent and pressure dependent boxes. The impacts are also demonstrated using the parametric analysis and numerical results to show the benefits of the static pressure reset including reducing fan power, cooling energy and heating energy.

Liu, M.; Feng, J.; Wang, Z.; Wu, L.; Zheng, K.; Pang, W.

2007-01-01T23:59:59.000Z

16

A Functional Test Procedure for the improved commissioning of a VAV system  

E-Print Network (OSTI)

In the context of the IEA40 research project, a specification of a Functional Test Procedure was progressively developed using the CA-MET building in Namur as real size test bench for the application and validation of the procedure. The target system is a typical VAV system devoted to the ventilation, cooling and air conditioning functions. The procedure consists in a series of operations to be applied to the system, considered as a set of connected components and taking into account the following constraints: 1) time availability 2) intrinsic limitations of the system 3) reference performances. The proposed procedure is divided in two sets of actions: 1) a number of preliminary actions allowing to take the best benefit of the subsequent phases: a) identification of available measurement points b) identification of actuators characteristics c) identification of control strategies d) aeraulic network calculations e) selection of measurement techniques and experimental design 2) the verification tasks themselves: The philosophy of the verification process is to bring the system into a number of states which allowed each specific check to be carried out. The organisation of the procedure tries to optimize the time spent for commissioning by logically sequencing the operations according to the following order: 1) test in manual (ie not controlled by the BEMS) operation 2) test in manual (ie not controlled by the BEMS) stop 3) test in normal operation 4) test at maximum flowrate 5) test at minimum flowrate 6) test in automatic stop The paper will provide the specific operations to be carried out at each step and will illustrate the whole process with the prototyping work performed on the CA-MET building in Namur.

Andre, P.; Lacote, P.; Aparecida Silva, C.; Hannay, J.; Lebrun, J.

2004-01-01T23:59:59.000Z

17

Problem of Vain Energy Consumption in a VAV Air Conditioning System Shared By an Inner Zone and Exterior Zone  

E-Print Network (OSTI)

In northern China, there are a large number of space buildings divided in inner zone and exterior zone based on usage requirements. The exterior zone needs to be heated in winter and cooled in summer, while the inner zone needs to be cooled both in winter and summer. Taking a practical project as example, this paper analyzes the energy consumption of a VAV air conditioning system that is shared by inner zone and exterior zone. The paper also points out the serious problem of useless energy consumption for this kind of system.

Wenji, G.; Ling, C.; Dongdong, L.; Mei, S.; Li, Z.

2006-01-01T23:59:59.000Z

18

System dynamics based models for selecting HVAC systems for office buildings: a life cycle assessment from carbon emissions perspective.  

E-Print Network (OSTI)

??This study aims to explore the life cycle environmental impacts of typical heating ventilation and air condition (HVAC) systems including variable air volume (VAV) system, (more)

Chen, S

2011-01-01T23:59:59.000Z

19

Impacts of Static Pressure Reset on VAV System Air Leakage, Fan Power and Thermal Energy - Part 2: Case Demonstration for a Typical Climate System  

E-Print Network (OSTI)

In Part 1 of this paper, the theoretical models, integrating the fan airflow, fan head, air leakage factors, are developed to analyze the impacts of the static pressure reset on both pressure dependent and pressure independent terminal boxes. In this part, a simulated air handling unit (AHU) system in Omaha NE is used to demonstrate the energy savings performance in one typical climate year. This AHU system has a static pressure reset system and two constant static pressure systems, one having pressure dependent terminal boxes and one having pressure independent terminal boxes. These simulated systems were compared mainly on the basis of fan power energy consumption and thermal energy consumption in totally a year. The example presents a good agreement with the theoretical model and simulation results. It was also shown that static pressure reset provides a promising and challenging way for the energy performance in VAV system.

Liu, M.; Zheng, K.; Wu, L.; Wang, Z.; Johnson, C.

2007-01-01T23:59:59.000Z

20

Precision volume measurement system.  

Science Conference Proceedings (OSTI)

A new precision volume measurement system based on a Kansas City Plant (KCP) design was built to support the volume measurement needs of the Gas Transfer Systems (GTS) department at Sandia National Labs (SNL) in California. An engineering study was undertaken to verify or refute KCP's claims of 0.5% accuracy. The study assesses the accuracy and precision of the system. The system uses the ideal gas law and precise pressure measurements (of low-pressure helium) in a temperature and computer controlled environment to ratio a known volume to an unknown volume.

Fischer, Erin E.; Shugard, Andrew D.

2004-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Improving Control of a Dual-Duct Single-Fan Variable Air Volume Systems  

E-Print Network (OSTI)

This paper discusses improved control strategies for dual-duct single-fan variable air volume (VAV) systems. Common control strategy for supply air volume modulation is evaluated, and an improved air volume control strategy that maintains separate cold and hot air duct static pressure set points is presented. The paper also explores the interactions between the cold and hot deck temperatures and duct static pressures, and discusses the impact of non-ideal deck temperature settings on duct static pressures and overall system energy consumption. To compensate the negative impact of non-ideal cold and hot deck temperature set points, the authors propose using real-time duct static pressure readings as feedback signals to fine-tune the deck temperature set points. These new control schemes can reduce simultaneous cooling and heating while reducing fan power consumption.

Wei, G.; Martinez, J.; Minihan, T.; Brundidge, T.; Claridge, D. E.; Turner, W. D.

2003-01-01T23:59:59.000Z

22

Room Temperature Control During Season Switchover with Single Duct Variable Air Volume System Without Reheat  

E-Print Network (OSTI)

The Langford A building houses the College of Architecture on TAMU campus. There are ten singleduct variable air volume (VAV) air-handling units (AHUs) without reheat serving the building. The local pneumatic thermostats modulate the dampers of VAV boxes to maintain room temperature at their setpoints. The thermostat action is switched from direct acting (DA) to reverse acting (RA) when the season changes from fall to winter and vice versa from winter to spring, based on the out side air temperature, when season changes. This results in various parts of the building ether too cold or too hot during the season change. This paper presents that the thermostat action will be switched according to cooling loads or discharge air temperature, instead of outside air temperature. For the interior zone, thermostat action does not need to be switched at all. The comfort is improved and savings is achieved by the new control scheme. Because some air-handling units (AHUs) serve both interior and exterior zones, this system never worked as intended. The system must be modified to have zone reheat and the AHUs discharge air temperature is set below dew point for humidity control.

Liu, C.; Deng, S.; Claridge, D. E.; Turner, W. D.; Bruner, H.

2003-01-01T23:59:59.000Z

23

96 ASHRAE Transactions: Research Current duct design methods for variable air volume  

E-Print Network (OSTI)

96 ASHRAE Transactions: Research ABSTRACT Current duct design methods for variable air volume (VAV in the 1997 ASHRAE Handbook--Fundamentals (ASHRAE 1997): equal friction, static regain, and the T Systems Taecheol Kim Jeffrey D. Spitler, Ph.D., P.E. Ronald D. Delahoussaye, Ph.D. Member ASHRAE Taecheol

24

Development of a Laboratory Verified Single-Duct VAV System Model with Fan Powered Terminal Units Optimized Using Computational Fluid Dynamics  

E-Print Network (OSTI)

Single Duct Variable Air Volume (SDVAV) systems use series and parallel Fan Powered Terminal Units to control the air flow in conditioned spaces. This research developed a laboratory verified model of SDVAV systems that used series and parallel fan terminal units where the fan speeds were controlled by either Silicon Controlled Rectifiers (SCR) or Electronically Commutated Motors (ECM) motors. As part of the research, the model was used to compare the performance of the systems and to predict the harmonics generated by ECM systems. All research objectives were achieved. The CFD model, which was verified with laboratory measurements, showed the potential to identify opportunities for improvement in the design of the FPTU and accurately predicted the static pressure drop as air passed through the unit over the full operating range of the FPTU. Computational fluid dynamics (CFD) models of typical a FPTU were developed and used to investigate opportunities for optimizing the design of FPTUs. The CFD model identified key parameters required to conduct numerical simulations of FPTU and some of the internal components used to manufacture the units. One key internal component was a porous baffle used to enhance mixing when primary air and induced air entered the mixing chamber. The CFD analysis showed that a pressure-drop based on face velocity model could be used to accurately predict the performance of the FPTU. The SDVAV simulation results showed that parallel FPTUs used less energy overall than series systems that used SCR motors as long as primary air leakage was not considered. Simulation results also showed that series ECM FPTUs used about the same amount of energy, within 3 percent, of parallel FPTU even when leakage was not considered. A leakage rate of 10 percent was enough to reduce the performance of the parallel FPTU to the level of the series SCR system and the series ECM FPTUs outperformed the parallel FPTUs at all weather locations used in the study.

Davis, Michael A.

2010-08-01T23:59:59.000Z

25

Performance of ECM controlled VAV fan powered terminal units  

E-Print Network (OSTI)

Empirical performance models of fan airflow, primary airflow and power consumption were developed for series and parallel variable air volume fan powered terminal units. An experimental setup and test procedure were created to test the terminal units at typical design pressures and airflows. Each terminal unit observed in this study used an 8 in (20.3 cm) primary air inlet. Two fan motor control methods were considered. The primary control of interest was the electronically commutated motor (ECM) controller. Data collected were compared with previous research regarding silicon rectified control (SCR) units. Generalized models were developed for both series and parallel terminal units. Coefficients for performance models were then compared with comparable SCR controlled units. Non-linear statistical modeling was performed using SPSS software (2008). In addition to airflow and power consumption modeling, power quality was also quantified. Relationships between real power (watts) and apparent power (VA) were presented as well as harmonic frequencies and total harmonic distortion. Power quality was recorded for each ECM controlled terminal unit tested. Additional tests were also made to SCR controlled terminal units used in previous research (Furr 2006). The airflow and power consumption performance models had an R2 equal to 0.990 or greater for every terminal unit tested. An air leakage model was employed to account for leakage in the parallel designed VAV terminal units when the internal fan was turned off. For the leakage model, both ECM and SCR controlled units achieved an R2 greater than or equal to 0.918.

Cramlet, Andrew Charles

2008-08-01T23:59:59.000Z

26

Supply Fan Control for Constant Air Volume Air Handling Units  

E-Print Network (OSTI)

Since terminal boxes do not have a modulation damper in constant volume (CV) air handling unit (AHU) systems, zone reheat coils have to be modulated to maintain the space temperature with constant supply airflow. This conventional control sequence causes a significant amount of reheat and constant fan power under partial load conditions. Variable Frequency Drives (VFDs) can be installed on these constant air volume systems. The fan speed can be modulated based on the maximum zone load. This paper present the procedure to control the supply fan speed and analyzes the thermal performance and major fan energy and thermal energy savings without expensive VAV retrofit through the actual system operation.

Cho, Y.; Wang, G.; Liu, M.

2007-01-01T23:59:59.000Z

27

Single-Duct Constant Air Volume System Supply Air Temperature Reset: Using Return Air Temperature or Outside Air Temperature?  

E-Print Network (OSTI)

The supply air temperature set point for a singleduct constant air volume air handling unit (AHU) system is often reset based on either return air temperature or outside air temperature in order to reduce simultaneous cooling and heating energy consumption. Both reset strategies make engineering sense as long as the reset schedules are reasonable. Quite often the decision to use one over the other is made with the assumption that they will all achieve some sorts of energy savings. However, the impact of these two strategies on AHU energy consumption could be very different. A comparison of these two commonly used supply air temperature reset strategies for a single-duct constant air volume system is presented in this paper. It is shown that from either the building energy consumption or building comfort point of view, the reset strategy based on outside air temperature is inherently better than that based on return air temperature. Significant amount of heating energy savings can be achieved by switching from return air temperature based reset to outside air temperature based reset. The reset strategy can also benefit variable air volume (VAV) AHUs. An improved supply air temperature set point reset control strategy is proposed by combining and staging the outside air and return air temperature based resets.

Wei, G.; Turner, W. D.; Claridge, D.; Liu, M.

2002-01-01T23:59:59.000Z

28

Departmental Information Systems Engineering (Volume 1) | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Documents & Publications Departmental Information Systems Engineering (Volume 2) Systems Engineering Methodology (SEM) Audit Report: IG-0836 Energy.gov Careers & Internships...

29

Fault Detection and Diagnosis in Building HVAC Systems  

E-Print Network (OSTI)

in AHU of VAV system, Energy Conversion & Management, 30.energy efficient building management system, Energy Conversionenergy efficient building management system, Energy Conversion

Najafi, Massieh

2010-01-01T23:59:59.000Z

30

Comparison of energy efficiency between variable refrigerant flow systems and ground source heat pump systems  

E-Print Network (OSTI)

comparison of VAV and VRF air conditioning systems in anThe variable refrigerant flow (VRF) and ground source heatthe energy efficiency of VRF systems compared with GSHP

Hong, Tainzhen

2010-01-01T23:59:59.000Z

31

INTEGRATED ENERGY SYSTEMS: PRODUCTIVITY & BUILDING SCIENCE  

E-Print Network (OSTI)

of Large Commercial HVAC Systems Led by Erik Kolderup, Eley Associates, Inc. Advanced VAV System Design will modify their rating system for tubular daylighting devices; and 2) U-factor results will affect how NFRC) E3 10/03 Advanced VAV System Design Guideline (Eley) E4 5/03 Integrated Design of Small Commercial

32

Turbine-Generator Auxilary Systems, Volume 3  

Science Conference Proceedings (OSTI)

The updated Turbine-Generator Auxiliary Systems, Volume 3: Generator Hydrogen System Maintenance Guide provides nuclear and fossil plant personnel with operation and maintenance guidance on the generator hydrogen system.BackgroundInput from member utilities of EPRI Program 65 as well as the Institute of Nuclear Power Operations (INPO) have indicated that maintenance guides are needed for turbine-generator auxiliary systems. The first auxiliary system ...

2012-12-03T23:59:59.000Z

33

Development of HVAC System Performance Criteria Using Factorial Design and DOE-2 Simulation  

E-Print Network (OSTI)

A new approach is described for the development of Heating, Ventilating, and Air-conditioning (HVAC) System Performance Criteria for the Texas Building Energy Design Standard. This approach integrates a design of experimental methodology and DOE-2 simulation to identify the effects of control parameters on HVAC system energy performance. Three new criteria - transport, plant, and system performance factors-are used as measures of system performance. The procedure has been applied to the development of criteria for a variable-air-volume (VAV) and a constant-air-volume (CAV) system in three Texas climates. The results show that the air distribution system pressure loss, cooling coil exit temperature set-pint, operation of an economizer, and use of dead band controls have significant effects on air transport energy use and total system performance. The selection of control strategies and set-points have a clear impact on energy use. There is also a great energy-saving potential of converting from a CAV to a VAV system.

Hou, D.; Jones, J. W.; Hunn, B. D.; Banks, J. A.

1996-01-01T23:59:59.000Z

34

Blend surfaces for set theoretic volume modelling systems  

Science Conference Proceedings (OSTI)

Most volume modelling systems are very limited in the complexity of the surfaces which they support. This is satisfactory for basic models of most mechanical components, since the functional surfaces are not usually complex. However, there are often ... Keywords: computer aided design, curved surfaces, ray tracing, volume modelling

Alan E. Middleditch; Kenneth H. Sears

1985-07-01T23:59:59.000Z

35

ASHRAE Transactions: Research 105 Current duct design methods for variable air volume  

E-Print Network (OSTI)

ASHRAE Transactions: Research 105 ABSTRACT Current duct design methods for variable air volume (VAV for different design conditions are sought using a duct fitting database program as described in ASHRAE (1993 Jeffrey D. Spitler, Ph.D., P.E. Ronald D. Delahoussaye, Ph.D. Member ASHRAE Taecheol Kim is a Ph

36

Module Development and Simulation of the Variable Refrigerant Flow Air Conditioning System under Cooling Conditions in Energyplus  

E-Print Network (OSTI)

As a high-efficiency air conditioning scheme, the variable refrigerant flow (VRF) air-conditioning system is finding its way into medium-sized office buildings. Based on a generic dynamic building energy simulation environment, EnergyPlus, a new module is developed and the energy usage of the VRF system is investigated. This paper compares the energy consumption of the VRF system with that of two conventional air-conditioning systems, namely, the variable air volume (VAV) system and the fan-coil plus fresh air (FPFA) system. A generic office building is used to accommodate the different types of heating, ventilating, and air conditioning (HVAC) systems. Our objective is to examine the energy consumption of the VRF system applied to office buildings and make suggestions for evaluating and making decisions on HVAC systems in the early stages of building design. Simulation results show that the energy-saving potential of the VRF system is expected to achieve 22.2 percent and 11.7 percent, compared to the VAV system and the FPFA system, respectively. An energy-usage breakdown of electricity end-users in various systems is also presented.

Zhou, Y.; Wu, J.; Wang, R.; Shiochi, S.

2006-01-01T23:59:59.000Z

37

High-Temperature-High-Volume Lifting For Enhanced Geothermal Systems  

Open Energy Info (EERE)

Temperature-High-Volume Lifting For Enhanced Geothermal Systems Temperature-High-Volume Lifting For Enhanced Geothermal Systems Geothermal Project Jump to: navigation, search Last modified on July 22, 2011. Project Title High-Temperature-High-Volume Lifting For Enhanced Geothermal Systems Project Type / Topic 1 Recovery Act: Enhanced Geothermal Systems Component Research and Development/Analysis Project Type / Topic 2 High-Temperature-High-Volume Lifting Project Description The proposed scope of work is divided into three Phases. Overall system requirements will be established in Phase 1, along with an evaluation of existing lifting system capability, identification of technology limitations, and a conceptual design of an overall lifting system. In developing the system components in Phase 2, component-level tests will be conducted using GE facilities. Areas of development will include high-temperature drive system materials, journal and thrust bearings, and corrosion and erosion-resistant lifting pump components. Finally, in Phase 3, the overall lab-scale lifting system will be demonstrated in a flow loop that will be constructed at GE Global Research.

38

Activation of Vav by the Gammaherpesvirus M2 Protein Contributes to the Establishment of Viral Latency in B Lymphocytes  

E-Print Network (OSTI)

Gammaherpesviruses subvert eukaryotic signaling pathways to favor latent infections in their cellular reservoirs. To this end, they express proteins that regulate or replace functionally specific signaling proteins of eukaryotic cells. Here we describe a new type of such viral-host interaction that is established through M2, a protein encoded by murine gammaherpesvirus 68. M2 associates with Vav proteins, a family of phosphorylation-dependent Rho/Rac exchange factors that play critical roles in lymphocyte signaling. M2 expression leads to Vav1 hyperphosphorylation and to the subsequent stimulation of its exchange activity towards Rac1, a process mediated by the formation of a trimolecular complex with Src kinases. This heteromolecular complex is coordinated by proline-rich and Src family-dependent phosphorylated regions of M2. Infection of Vavdeficient mice with gammaherpesvirus 68 results in increased long-term levels of latency in germinal center B lymphocytes, corroborating the importance of the M2/Vav cross talk in the process of viral latency. These results reveal a novel strategy used by the murine gammaherpesvirus family to subvert the lymphocyte signaling machinery to its own benefit. The persistence of herpesvirus in the infected organism is dictated by the establishment of latency in particular cell types within the host. In the case of gammaherpesviruses, such as

Lnia Rodrigues; Marta Pires De Mir; Mara J. Caloca; Xos R. Bustelo; J. Pedro Simas

2005-01-01T23:59:59.000Z

39

Integrated safety management system verification: Volume 2  

Science Conference Proceedings (OSTI)

Department of Energy (DOE) Policy (P) 450.4, Safety Management System Policy, commits to institutionalization of an Integrated Safety Management System (ISMS) throughout the DOE complex. The DOE Acquisition Regulations (DEAR, 48 CFR 970) requires contractors to manage and perform work in accordance with a documented Integrated Safety Management System (ISMS). Guidance and expectations have been provided to PNNL by incorporation into the operating contract (Contract DE-ACM-76FL0 1830) and by letter. The contract requires that the contractor submit a description of their ISMS for approval by DOE. PNNL submitted their proposed Safety Management System Description for approval on November 25,1997. RL tentatively approved acceptance of the description pursuant to a favorable recommendation from this review. The Integrated Safety Management System Verification is a review of the adequacy of the ISMS description in fulfilling the requirements of the DEAR and the DOE Policy. The purpose of this review is to provide the Richland Operations Office Manager with a recommendation for approval of the ISMS description of the Pacific Northwest Laboratory based upon compliance with the requirements of 49 CFR 970.5204(-2 and -78); and to verify the extent and maturity of ISMS implementation within the Laboratory. Further the review will provide a model for other DOE laboratories managed by the Office of Assistant Secretary for Energy Research.

Christensen, R.F.

1998-08-10T23:59:59.000Z

40

Power Shape Monitoring System (PSMS), Volume 1: Overview and Performance  

Science Conference Proceedings (OSTI)

Volume 1 provides an overview of the first-generation power shape monitoring system (PSMS) for BWRs, which has been undergoing field testing at the Oyster Creek nuclear plant. The system's functional requirements and its hardware and software are described. The accuracy of the Oyster Creek PSMS is evaluated--specifically, its power prediction capabilities.

1981-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Integrated safety management system verification: Volume 1  

SciTech Connect

Department of Energy (DOE) Policy (P) 450.4, Safety Management System Policy, commits to institutionalizing an Integrated Safety Management System (ISMS) throughout the DOE complex. The DOE Acquisition Regulations (DEAR 48 CFR 970) requires contractors to manage and perform work in accordance with a documented Integrated Safety Management System. The Manager, Richland Operations Office (RL), initiated a combined Phase 1 and Phase 2 Integrated Safety Management Verification review to confirm that PNNL had successfully submitted a description of their ISMS and had implemented ISMS within the laboratory facilities and processes. A combined review was directed by the Manager, RL, based upon the progress PNNL had made in the implementation of ISM. This report documents the results of the review conducted to verify: (1) that the PNNL integrated safety management system description and enabling documents and processes conform to the guidance provided by the Manager, RL; (2) that corporate policy is implemented by line managers; (3) that PNNL has provided tailored direction to the facility management; and (4) the Manager, RL, has documented processes that integrate their safety activities and oversight with those of PNNL. The general conduct of the review was consistent with the direction provided by the Under Secretary`s Draft Safety Management System Review and Approval Protocol. The purpose of this review was to provide the Manager, RL, with a recommendation to the adequacy of the ISMS description of the Pacific Northwest Laboratory based upon compliance with the requirements of 49 CFR 970.5204(-2 and -78); and, to provide an evaluation of the extent and maturity of ISMS implementation within the Laboratory. Further, this review was intended to provide a model for other DOE Laboratories. In an effort to reduce the time and travel costs associated with ISM verification the team agreed to conduct preliminary training and orientation electronically and by phone. These activities are normally conducted during a pre-visit trip to the site. The Team recommends approval of the Integrated Safety Management System Description subject to the resolution of the Areas of Concerns noted here.

Christensen, R.F.

1998-08-12T23:59:59.000Z

42

Simulation of the Post-Retrofit Thermal Energy Use for the Perry-Castaneda Library Building with the Use of Simplified System Models  

E-Print Network (OSTI)

Several state owned buildings with dual-duct constant volume (DDCV) systems are being retrofitted with energy efficient variable air volume (VAV) systems as part of Texas LoanSTAR Program. One method of determining the energy savings resulting from energy conserving retrofits relies on the use of a model for the daily whole building consumption, Epre, in the pre-retrofit configuration. Epre is typically a function of primary influencing parameters such as ambient temperature, humidity, building internal gains and others (Figure 1). Following the retrofit, the energy saved, E,av is determined using measured daily consumption, Emea3 as shown in Figure 1. This method is being used in the Texas LoanSTAR monitoring and analysis program for buildings that have adequate pre-retrofit monitored data. Unfortunately, in the Perry-Castaneda Library (PCL) building, the retrofits were completed before the monitoring instrumentation was installed. Therefore, no pre-retrofit monitored data are available for this building. Hence another method to estimate savings is needed. Such a method was developed and tested (Katipamula and Claridge 1991). This method was based on the use of the ASHRAE TC 4.7 simplified energy analysis procedure (SEAP). It involved developing one model each for the VAV (post-retrofit system) and the DDCV (pre-retrofit system) systems.

Katipamula, S.; Claridge, D. E.

1991-01-01T23:59:59.000Z

43

Simulation of the Post-Retrofit Thermal Energy Use for the University Teaching Center (UTC) Building with the Use of Simplified System Models  

E-Print Network (OSTI)

Several state owned buildings with dual-duct constant volume (DDCV) systems have been retrofitted with energy efficient variable air volume systems (VAV) as part of the Texas LoanSTAR Program. One method of determining the energy savings resulting from energy conserving retrofits relies on the use of a model for the daily whole building consumption, Epre, in the pre-retrofit configuration. Epre is typically a function of primary influencing parameters such as ambient temperature, humidity, building internal gains and others (Figure 1). Following the retrofit, the energy saved, Esav is determined using measured daily consumption, Emea3 as shown in Figure 1. This method is being used in the Texas LoanSTAR monitoring and analysis program for buildings that have adequate pre-retrofit monitored data (Kelly et al., 1992). Unfortunately, in the University Teaching Center (UTC) the retrofits were completed before the monitoring instrumentation was installed. Therefore, no pre-retrofit monitored data are available. Hence another method to estimate savings was needed. Such a method was developed and tested on a large engineering center (Katipamula and Claridge 1991). This method was based on the use of the ASHRAE TC 4.7 simplified energy analysis procedure (SEAP). It involved developing one model each for the VAV (post-retrofit system) and the DDCV (pre-retrofit system) systems.

Katipamula, S.; Claridge, D. E.

1991-01-01T23:59:59.000Z

44

Power Plant Electrical Reference Series, Volumes 1-16: Volume 1: Electric Generators; Volume 2: Power Transformers; Volume 3: Auxili ary System Planning; Volume 4: Wire and Cable; Volume 5: Grounding and Lightning Protection; Volume 6: Motors; Volume 7..  

Science Conference Proceedings (OSTI)

This comprehensive and practical guide to electric power apparatus and electrical phenomena provides an up-to-date source book for power plant managers, engineers, and operating personnel. Aiding in the recognition and prevention of potential problems, the 16-volume guide can help utilities save staff time and reduce operating expenses.

1988-05-01T23:59:59.000Z

45

Turbine-Generator Auxiliary Systems, Volume 2: Turbine Steam Seal System Maintenance Guide  

Science Conference Proceedings (OSTI)

The Turbine-Generator Auxiliary Systems, Volume 2: Turbine Steam Seal System Maintenance Guide provides nuclear and fossil plant personnel with operation and maintenance guidance on the turbine steam seal system components.

2006-12-14T23:59:59.000Z

46

Verification and validation guidelines for high integrity systems. Volume 1  

SciTech Connect

High integrity systems include all protective (safety and mitigation) systems for nuclear power plants, and also systems for which comparable reliability requirements exist in other fields, such as in the process industries, in air traffic control, and in patient monitoring and other medical systems. Verification aims at determining that each stage in the software development completely and correctly implements requirements that were established in a preceding phase, while validation determines that the overall performance of a computer system completely and correctly meets system requirements. Volume I of the report reviews existing classifications for high integrity systems and for the types of errors that may be encountered, and makes recommendations for verification and validation procedures, based on assumptions about the environment in which these procedures will be conducted. The final chapter of Volume I deals with a framework for standards in this field. Volume II contains appendices dealing with specific methodologies for system classification, for dependability evaluation, and for two software tools that can automate otherwise very labor intensive verification and validation activities.

Hecht, H.; Hecht, M.; Dinsmore, G.; Hecht, S.; Tang, D. [SoHaR, Inc., Beverly Hills, CA (United States)

1995-03-01T23:59:59.000Z

47

Case Studies of Grid-Connected Photovoltaic Systems, Volume 3  

Science Conference Proceedings (OSTI)

The photovoltaics industry is growing rapidly, and photovoltaic (PV) power is likely to become an increasingly significant source of distributed generation as its cost declines over the next ten years. This report completes a series of three volumes documenting more than a dozen grid-connected PV case studies in all and covering a broad range of system configurations and project types. The report provides field experience useful to improve the design of future PV systems and identifies problems that need...

2004-03-30T23:59:59.000Z

48

Preliminary systems design study assessment report. Volume 7, Subsystem concepts  

SciTech Connect

The System Design Study (SDS), part of the Waste Technology Development Department at the Idaho National Engineering Laboratory (INEL), examined techniques available for the remediation of hazardous and transuranic waste stored at the Radioactive Waste Management Complex`s Subsurface Disposal Area at the INEL. Using specific technologies, system concepts for treating the buried waste and the surrounding contaminated soil were evaluated. Evaluation included implementability, effectiveness, and cost. The SDS resulted in the development of technology requirements including demonstration, testing, and evaluation activities needed for implementing each. This volume contains the descriptions and other relevant information of the four subsystems required for most of the ex situ processing systems. This volume covers the metal decontamination and sizing subsystem, soils processing subsystem, low-level waste subsystem, and retrieval subsystem.

Mayberry, J.L.; Feizollahi, F.; Del Signore, J.C.

1992-01-01T23:59:59.000Z

49

Conceptual design and systems analysis of photovoltaic systems. Volume II. Study results. Final report  

DOE Green Energy (OSTI)

This investigation of terrestrial PV systems considered the technical and economic feasibility for systems in three size categories: a small system of about 12 kW peak output for on-site residential use; a large 1500 MW central power plant contributing to the bulk energy of a utility system power grid; and an intermediate size system of about 250 kW for use on public or commercial buildings. In each category, conceptual designs were developed, performance was analyzed for a range of climatic regions, economic analyses were performed, and assessments were made of pertinent institutional issues. The report consists of three volumes. Volume I contains a Study Summary of the major study results. This volume contains the detailed results pertaining to on-site residential photovoltaic systems, central power plant photovoltaic systems, and intermediate size systems applied to commercial and public buildings. Volume III contains supporting appendix material. (WHK)

Kirpich, A.

1977-03-19T23:59:59.000Z

50

Building Energy Software Tools Directory: EZDOE  

NLE Websites -- All DOE Office Websites (Extended Search)

and much more. The Systems data involves all information concerning air handling and heat delivery systems. VAV, constant volume, PTAC, dual duct, twofour pipe fan coils, and...

51

Shared Communications: Volume 2. In-Depth Systems Research  

Science Conference Proceedings (OSTI)

This report is the second of two documents that examine the literature for actual examples of organizations and agencies that share communications resources. While the primary emphasis is on rural, intelligent transportation system (ITS) communications involving transit, examples will not be limited to rural activities, nor to ITS implementation, nor even to transit. In addition, the term ''communication'' will be broadly applied to include all information resources. The first document of this series, ''Shared Communications: Volume I. A Summary and Literature Review'', defines the meaning of the term ''shared communication resources'' and provides many examples of agencies that share resources. This document, ''Shared Communications: Volume II. In-Depth Systems Research'', reviews attributes that contributed to successful applications of the sharing communication resources concept. A few examples of each type of communication sharing are provided. Based on the issues and best practice realworld examples, recommendations for potential usage and recommended approaches for field operational tests are provided.

Truett, LF

2004-09-22T23:59:59.000Z

52

Quantifying Volume Changing Perturbations in a Wave Chaotic System  

E-Print Network (OSTI)

A sensor was developed to quantitatively measure perturbations which change the volume of a wave chaotic cavity while leaving its shape intact. The sensors work in the time domain by using either scattering fidelity of the transmitted signals or time reversal mirrors. The sensors were tested experimentally by inducing volume changing perturbations to a one cubic meter mixed chaotic and regular billiard system. Perturbations which caused a volume change that is as small as 54 parts in a million were quantitatively measured. These results were obtained by using electromagnetic waves with a wavelength of about 5cm, therefore, the sensor is sensitive to extreme sub-wavelength changes of the boundaries of a cavity. The experimental results were compared with Finite Difference Time Domain (FDTD) simulation results, and good agreement was found. Furthermore, the sensor was tested using a frequency domain approach on a numerical model of the star graph, which is a representative wave chaotic system. These results open up interesting applications such as: monitoring the spatial uniformity of the temperature of a homogeneous cavity during heating up / cooling down procedures, verifying the uniform displacement of a fluid inside a wave chaotic cavity by another fluid, etc.

Biniyam Tesfaye Taddese; Gabriele Gradoni; Franco Moglie; Thomas M. Antonsen; Edward Ott; Steven M. Anlage

2012-08-27T23:59:59.000Z

53

Photovoltaic systems concept study. Volume IV. Final report  

DOE Green Energy (OSTI)

This report has been prepared in nine sections plus appendices, separated into five separate volumes. This volume contains three sections. Separate abstracts were prepared for each section. (MHR)

Not Available

1977-04-01T23:59:59.000Z

54

High volume tidal or current flow harnessing system  

Science Conference Proceedings (OSTI)

Apparatus permitting the utilization of large volumes of water in the harnessing and extracting of a portion of the power generated by the rise and fall of ocean tides, ocean currents, or flowing rivers includes the provision of a dam, and a specialized single cavity chamber of limited size as compared with the water head enclosed by the dam, and an extremely high volume gating system in which all or nearly all of the water between the high and low levels on either side of the dam is cyclically gated through the single chamber from one side of the dam to the other so as to alternately provide positive air pressure and a partial vacuum within the single chamber. In one embodiment, the specialized chamber has a barrier at the bottom which divides the bottom of the chamber in half, large ports at the bottom of the chamber to permit inflow and outflow of high volumes of water, and ganged structures having a higher total area than that of corresponding ports, in which the structures form sluice gates to selectively seal off and open different sets of ports. In another embodiment, a single chamber is used without a barrier. In this embodiment, vertical sluice gates are used which may be activated automatically by pressures acting on the sluice gates as a result of ingested and expelled water.

Gorlov, A.M.

1984-08-07T23:59:59.000Z

55

Flow Analysis on a Limited Volume Chilled Water System  

SciTech Connect

LANL Currently has a limited volume chilled water system for use in a glove box, but the system needs to be updated. Before we start building our new system, a flow analysis is needed to ensure that there are no high flow rates, extreme pressures, or any other hazards involved in the system. In this project the piping system is extremely important to us because it directly affects the overall design of the entire system. The primary components necessary for the chilled water piping system are shown in the design. They include the pipes themselves (perhaps of more than one diameter), the various fitting used to connect the individual pipes to form the desired system, the flow rate control devices (valves), and the pumps that add energy to the fluid. Even the most simple pipe systems are actually quite complex when they are viewed in terms of rigorous analytical considerations. I used an 'exact' analysis and dimensional analysis considerations combined with experimental results for this project. When 'real-world' effects are important (such as viscous effects in pipe flows), it is often difficult or impossible to use only theoretical methods to obtain the desired results. A judicious combination of experimental data with theoretical considerations and dimensional analysis are needed in order to reduce risks to an acceptable level.

Zheng, Lin [Los Alamos National Laboratory

2012-07-31T23:59:59.000Z

56

Small power systems study. Volume. Study results. Technical summary report  

DOE Green Energy (OSTI)

The Division of Solar Technology of the Department of Energy is currently examining the market potential of a number of dispersed solar energy systems, including the small (less than or equal to 10 MW/sub e/) solar thermal power system. Small fossil-fueled generating units in the United States utility system, (i.e., investor-owned, municipal, and cooperatives) have a current capacity of approximately 8000 MW/sub e/ or about 1.5 percent of the total US electrical capacity, and provide a large potential market for small solar thermal power systems. The Small Power Systems Study has as its objective the determination of conditions under which small (less than or equal to 10 MW/sub e/) solar thermal power units can provide cost-effective electrical power to a variety of users. Potential users, in addition to the utility systems; include Department of Defense installations and applications, remote mining and/or lumbering operations, and other industrial power systems with and without cogeneration. The first year's results on the Small Power Systems Study are summarized. The data base used and the breakeven cost analysis are discussed. Information on both small (less than or equal to 10 MW/sub e/) generating units and the utility systems using them is presented as well as data on fossil fuel costs, solar plant costs, and solar insolation values. The results of a survey of Department of Defense (DOD) worldwide electrical generating capacity at its military bases and on a potential DOD application are presented. Information on a potential small solar power system experiment in the interior of Alaska is given, and a limited amount of information on a remote application which would provide power or a large open pit copper mine is presented. Volume II of this Technical Summary Report contains an inventory, by state, of the small (less than or equal to 10 MW/sub e/) generating units in the US utility system. (WHK)

Sitney, L.R.

1978-05-31T23:59:59.000Z

57

Small power systems study. Volume. Study results. Technical summary report  

SciTech Connect

The Division of Solar Technology of the Department of Energy is currently examining the market potential of a number of dispersed solar energy systems, including the small (less than or equal to 10 MW/sub e/) solar thermal power system. Small fossil-fueled generating units in the United States utility system, (i.e., investor-owned, municipal, and cooperatives) have a current capacity of approximately 8000 MW/sub e/ or about 1.5 percent of the total US electrical capacity, and provide a large potential market for small solar thermal power systems. The Small Power Systems Study has as its objective the determination of conditions under which small (less than or equal to 10 MW/sub e/) solar thermal power units can provide cost-effective electrical power to a variety of users. Potential users, in addition to the utility systems; include Department of Defense installations and applications, remote mining and/or lumbering operations, and other industrial power systems with and without cogeneration. The first year's results on the Small Power Systems Study are summarized. The data base used and the breakeven cost analysis are discussed. Information on both small (less than or equal to 10 MW/sub e/) generating units and the utility systems using them is presented as well as data on fossil fuel costs, solar plant costs, and solar insolation values. The results of a survey of Department of Defense (DOD) worldwide electrical generating capacity at its military bases and on a potential DOD application are presented. Information on a potential small solar power system experiment in the interior of Alaska is given, and a limited amount of information on a remote application which would provide power or a large open pit copper mine is presented. Volume II of this Technical Summary Report contains an inventory, by state, of the small (less than or equal to 10 MW/sub e/) generating units in the US utility system. (WHK)

Sitney, L.R.

1978-05-31T23:59:59.000Z

58

Guidelines for the verification and validation of expert system software and conventional software: Bibliography. Volume 8  

Science Conference Proceedings (OSTI)

This volume contains all of the technical references found in Volumes 1-7 concerning the development of guidelines for the verification and validation of expert systems, knowledge-based systems, other AI systems, object-oriented systems, and conventional systems.

Miller, L.A.; Hayes, J.E.; Mirsky, S.M. [Science Applications International Corp., McLean, VA (United States)

1995-03-01T23:59:59.000Z

59

Analysis of automated highway system risks and uncertainties. Volume 5  

SciTech Connect

This volume describes a risk analysis performed to help identify important Automated Highway System (AHS) deployment uncertainties and quantify their effect on costs and benefits for a range of AHS deployment scenarios. The analysis identified a suite of key factors affecting vehicle and roadway costs, capacities and market penetrations for alternative AHS deployment scenarios. A systematic protocol was utilized for obtaining expert judgments of key factor uncertainties in the form of subjective probability percentile assessments. Based on these assessments, probability distributions on vehicle and roadway costs, capacity and market penetration were developed for the different scenarios. The cost/benefit risk methodology and analysis provide insights by showing how uncertainties in key factors translate into uncertainties in summary cost/benefit indices.

Sicherman, A.

1994-10-01T23:59:59.000Z

60

Recent Developments of the Modelica"Buildings" Library for Building Energy and Control Systems  

Science Conference Proceedings (OSTI)

At the Modelica 2009 conference, we introduced the Buildings library, a freely available Modelica library for building energy and control systems. This paper reports the updates of the library and presents example applications for a range of heating, ventilation and air conditioning (HVAC) systems. Over the past two years, the library has been further developed. The number of HVAC components models has been doubled and various components have been revised to increase numerical robustness.The paper starts with an overview of the library architecture and a description of the main packages. To demonstrate the features of the Buildings library, applications that include multizone airflow simulation as well as supervisory and local loop control of a variable air volume (VAV) system are briefly described. The paper closes with a discussion of the current development.

Wetter, Michael; Zuo, Wangda; Nouidui, Thierry Stephane

2011-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Duct leakage impacts on VAV system performance in California large commercial buildings  

E-Print Network (OSTI)

GLOSSARY 34 REFERENCES. 34 APPENDIX I: BUILDING SCHEDULES.. 37 APPENDIX II: REGRESSION EQUATIONS AND COEFFICIENTS . 40 APPENDIX III: ENERGY

Wray, Craig P.; Matson, Nance E.

2003-01-01T23:59:59.000Z

62

Duct leakage impacts on VAV system performance in California large commercial buildings  

E-Print Network (OSTI)

kW) Total Fan Power (kW) Climate Zone CZ3 (Oakland) CZ9 (Coil Sizes (kBtu/(hfloor)) Climate Zone CZ3 (Oakland) CZ9 (all three vintages and climate zones ranged from 0.9999 to

Wray, Craig P.; Matson, Nance E.

2003-01-01T23:59:59.000Z

63

Duct leakage impacts on VAV system performance in California large commercial buildings  

E-Print Network (OSTI)

air leakage rate, then proposed buildings will be rewarded for sealingduct sealing even more cost-effective. Table 5. TRNSYS Air-

Wray, Craig P.; Matson, Nance E.

2003-01-01T23:59:59.000Z

64

Duct leakage impacts on VAV system performance in California large commercial buildings  

E-Print Network (OSTI)

divided by the supply fan design airflow. The downstreamThe supply (and return) fan design airflow was determined byThe intermediate-floor supply fan design airflows for each

Wray, Craig P.; Matson, Nance E.

2003-01-01T23:59:59.000Z

65

Duct leakage impacts on VAV system performance in California large commercial buildings  

E-Print Network (OSTI)

electricity consumption, and boiler natural gas consumption. Using yearelectricity consumption, and boiler natural gas consumption. Using yearelectricity consumption, and boiler natural gas consumption. Using year

Wray, Craig P.; Matson, Nance E.

2003-01-01T23:59:59.000Z

66

Duct leakage impacts on VAV system performance in California large commercial buildings  

E-Print Network (OSTI)

chiller and cooling tower electricity consumption, boilerchiller and cooling tower electricity consumption, boilerheat outdoors using a cooling tower. A natural-gas-fired

Wray, Craig P.; Matson, Nance E.

2003-01-01T23:59:59.000Z

67

Columbia River System Operation Review : Final Environmental Impact Statement, Appendix T (Second Continued Volume): Comments & Responses.  

DOE Green Energy (OSTI)

This is Appendix T (second continued volume) giving public comments and responses to the final environmental impact statement for the Columbia River System.

Columbia River System Operation Review (U.S.)

1995-11-01T23:59:59.000Z

68

System for the Analysis of Global Energy Markets (Sage)-Volume 2  

U.S. Energy Information Administration (EIA)

System for the Analysis of Global Energy Markets (SAGE) Volume 2 ... SAGE allows for time-stepped optimization and intra-period market adjustment algorithms.

69

A multiple camera system with real-time volume reconstruction for articulated skeleton pose tracking  

Science Conference Proceedings (OSTI)

We present a multi-camera system for recovering skeleton body pose, by performing real-time volume reconstruction and using a hierarchical stochastic pose search algorithm. Different from many multicamera systems that require a few connected workstations, ... Keywords: multi-camera system, pose estimation, real-time volume reconstruction

Zheng Zhang; Hock Soon Seah; Chee Kwang Quah; Alex Ong; Khalid Jabbar

2011-01-01T23:59:59.000Z

70

State energy price system. Volume I: overview and technical documentation  

SciTech Connect

This study utilizes existing data sources and previous analyses of state-level energy prices to develop consistent state-level energy prices series by fuel type and by end-use sector. The fuels are electricity, natural gas, coal, distillate fuel oil, motor gasoline, diesel, kerosene, jet fuel, residual fuel, and liquefied petroleum gas. The end-use sectors are residential, commercial, industrial, transportation, and electric utility. Based upon an evaluation of existing data sources, recommendations were formulated on the feasible approaches for developing a consistent state energy price series. The data series were compiled based upon the approaches approved after a formal EIA review. Detailed documentation was provided, including annual updating procedures. Recommendations were formulated for future improvements in the collection of data or in data processing. Generally, the geographical coverage includes the 50 states and the District of Columbia. Information on state-level energy use was generally taken from the State Energy Data System (SEDS). Corresponding average US prices are also developed using volumes reported in SEDS. To the extent possible, the prices developed are quantity weighted average retail prices. Both a Btu price series and a physical unit price series are developed for each fuel. The period covered by the data series is 1970 through 1980 for most fuels, though prices for electricity and natural gas extend back to 1960. (PSB)

Fang, J.M.; Nieves, L.A.; Sherman, K.L.; Hood, L.J.

1982-06-01T23:59:59.000Z

71

Hydro Life Extension Modernization Guides: Volumes 4 and 5: Auxiliary Mechanical and Electrical Systems  

Science Conference Proceedings (OSTI)

These guidelines are the fourth and fifth volumes in a series for assessing the needs and benefits and evaluating the cost and economic justification of life extension and modernization alternatives at hydroelectric plants and for implementing the selected plan. They specifically address the plant auxiliary mechanical systems (Volume 4) and auxiliary electrical systems (Volume 5). They also provide a screening procedure and criteria to enable utility personnel to identify where there are opportunities fo...

2001-12-17T23:59:59.000Z

72

Impact of the Variable Refrigerant Volume Air Conditioning System on Building Energy Efficiency  

E-Print Network (OSTI)

The application of the variable refrigerant volume multi-zone air conditioning systems has met with mixed results since the publication of the Design Standard for Energy Efficiency of Public Buildings. This paper analyzes the characteristics of the variable refrigerant volume multi-zone air conditioning system, and discusses the advantages of its application.

Zhu, H.

2006-01-01T23:59:59.000Z

73

System 80+{trademark} Standard Design: CESSAR design certification. Volume 9: Amendment I  

Science Conference Proceedings (OSTI)

This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80{sup +}{trademark} Standard Design. This volume 9 discusses Electric Power and Auxiliary Systems.

Not Available

1990-12-21T23:59:59.000Z

74

System 80+{trademark} Standard Design: CESSAR design certification. Volume 3: Amendment I  

SciTech Connect

This report, entitled Combustion Engineering Standard Safety Analysis Report - Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These documents describe the Combustion Engineering, Inc. System 80+{sup TM} Standard Design. This report, Volume 3, in conjunction with Volume 2, provides the design of structures, components, equipment and systems.

Not Available

1990-12-21T23:59:59.000Z

75

System 80+{trademark} Standard Design: CESSAR design certification. Volume 2: Amendment I  

SciTech Connect

This report, entitled Combustion Engineering Standard Safety Analysis Report - Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These documents describe the Combustion Engineering, Inc. System 80+{sup TM} Standard Design. This report, Volume 2, in conjunction with Volume 3, provides the design of structures, components, equipment and systems.

Not Available

1990-12-21T23:59:59.000Z

76

System 80+{trademark} Standard Design: CESSAR design certification. Volume 10: Amendment I  

Science Conference Proceedings (OSTI)

This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80{sup +}{trademark} Standard Design. This volume 10 discusses the Steam and Power Conversion System and Radioactive Waste Management.

Not Available

1990-12-21T23:59:59.000Z

77

Modeling of ECM Controlled Series Fan-powered VAV Terminal Units  

E-Print Network (OSTI)

Semi-empirical models for series fan-powered variable air volume terminal units (FPTUs) were developed based on models of the primary, plenum, fan airflow and the fan power consumption. The experimental setups and test procedures were developed respectively for primary, plenum and fan airflow to test each component of the FPTUs at typical design pressures and airflows. Two sizes of the terminal units from three manufacturers were used in this study. All of the FPTUs were equipped with electronically commutated motors (ECM). Data provided by the models were compared against the data from previous experiments to prove the models validity. Regression modeling was performed by using SigmaStat. The model of primary airflow had an R2 above 0.948 for all the terminal units evaluated while the plenum airflow model had an R2 above 0.99. For all the terminal units, the R2 of the fan airflow model was ranged from 0.973 to 0.998. Except for one fan, the fan power consumption model was able to characterize the power performance and had an R2 above 0.986. By combining the airflow and power models, the model for series FPTU was developed. Verification was made to prove the FPTU models validity by comparing the measured and predicted data of airflow and power consumption. Correction factors were used in the primary airflow model to compensate for the difference caused by large measurement errors and the system effects. The predicted values were consistent with measurements and no offset was needed in the primary airflow model. Generally, the newly established model was able to describe the airflow performance as well as power consumption of series FPTUs without adding complexity.

Yin, Peng

2010-08-01T23:59:59.000Z

78

Proceedings of the 9th International Conference on Autonomous Agents and Multiagent Systems: volume 1 - Volume 1: volume 1  

Science Conference Proceedings (OSTI)

The Autonomous Agents and Multi-agent Systems (AAMAS) conference series brings together researchers from around the world to share the latest advances in the field. It was initiated in 2002 as a merger of three highly successful related events: the International ...

Michael Luck; Sandip Sen

2010-05-01T23:59:59.000Z

79

Proceedings of the 9th International Conference on Autonomous Agents and Multiagent Systems: volume 3 - Volume 3: volume 3  

Science Conference Proceedings (OSTI)

The Autonomous Agents and Multi-agent Systems (AAMAS) conference series brings together researchers from around the world to share the latest advances in the field. It was initiated in 2002 as a merger of three highly successful related events: the International ...

Michael Luck; Sandip Sen

2010-05-01T23:59:59.000Z

80

Proceedings of the 9th International Conference on Autonomous Agents and Multiagent Systems: volume 2 - Volume 2: volume 2  

Science Conference Proceedings (OSTI)

The Autonomous Agents and Multi-agent Systems (AAMAS) conference series brings together researchers from around the world to share the latest advances in the field. It was initiated in 2002 as a merger of three highly successful related events: the International ...

Michael Luck; Sandip Sen

2010-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Systems Studies Department FY 78 activity report. Volume 2. Systems analysis. [Sandia Laboratories, Livermore  

DOE Green Energy (OSTI)

The Systems Studies Department at Sandia Laboratories Livermore (SLL) has two primary responsibilities: to provide computational and mathematical services and to perform systems analysis studies. This document (Volume 2) describes the FY Systems Analysis highlights. The description is an unclassified overview of activities and is not complete or exhaustive. The objective of the systems analysis activities is to evaluate the relative value of alternative concepts and systems. SLL systems analysis activities reflect Sandia Laboratory programs and in 1978 consisted of study efforts in three areas: national security: evaluations of strategic, theater, and navy nuclear weapons issues; energy technology: particularly in support of Sandia's solar thermal programs; and nuclear fuel cycle physical security: a special project conducted for the Nuclear Regulatory Commission. Highlights of these activities are described in the following sections. 7 figures. (RWR)

Gold, T.S.

1979-02-01T23:59:59.000Z

82

Heat Pump Thermal Distribution Systems, Volumes 1 and 2: Volumes 1 and 2  

Science Conference Proceedings (OSTI)

The thermal distribution system significantly affects the first cost and the operating cost of heat pumps. A detailed study has identified central and zoned systems that promise performance and cost benefits. This report discusses the thermal distribution system's applicability to air-source, ground-coupled, nonazeotropic refrigerant mixture and dual-fuel heat pumps.

1990-06-28T23:59:59.000Z

83

System 80+{trademark} Standard Design: CESSAR design certification. Volume 18: Amendment I  

SciTech Connect

This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80+{trademark} Standard Design. This Volume 18 provides Appendix B, Probabilistic Risk Assessment.

Not Available

1990-12-21T23:59:59.000Z

84

System 80+{trademark} Standard Design: CESSAR design certification. Volume 8: Amendment I  

SciTech Connect

This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80{sup +}{trademark} Standard Design. This volume 8 provides a description of instrumentation and controls.

Not Available

1990-12-21T23:59:59.000Z

85

System 80+{trademark} Standard Design: CESSAR design certification. Volume 11: Amendment I  

Science Conference Proceedings (OSTI)

This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80{sup +}{trademark} Standard Design. This volume 11 discusses Radiation Protection, Conduct of Operations, and the Initial Test Program.

Not Available

1990-12-21T23:59:59.000Z

86

Fourth international symposium on automotive propulsion systems. Volume I. [Eighteen papers  

DOE Green Energy (OSTI)

A pre-conference draft is given (in five volumes) of the proceedings of the 4th International Symposium on Automotive Propulsion Systems, held April 18-22, 1977, in Washington, D.C. Volume I contains eighteen papers; a separate abstract was prepared for each for ERDA Energy Research Abstracts (ERA).

Not Available

1977-01-01T23:59:59.000Z

87

Renewable Electricity Futures Study. Volume 4: Bulk Electric Power Systems: Operations and Transmission Planning  

NLE Websites -- All DOE Office Websites (Extended Search)

Bulk Electric Power Systems: Bulk Electric Power Systems: Operations and Transmission Planning Volume 4 of 4 Volume 2 PDF Volume 3 PDF Volume 1 PDF Volume 4 PDF NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. Renewable Electricity Futures Study Edited By Hand, M.M. National Renewable Energy Laboratory Baldwin, S. U.S. Department of Energy DeMeo, E. Renewable Energy Consulting Services, Inc. Reilly, J.M. Massachusetts Institute of Technology Mai, T. National Renewable Energy Laboratory Arent, D. Joint Institute for Strategic Energy Analysis Porro, G. National Renewable Energy Laboratory Meshek, M. National Renewable Energy Laboratory Sandor, D. National Renewable

88

Photovoltaic systems concept study. Final report. Volume I  

DOE Green Energy (OSTI)

Conceptual system designs were developed for three sizes of photovoltaic solar electric power systems: a single family residence, a central station power plant, and two on-site intermediate systems (shopping center and commercial retrofit). A brief system description and a summary of primary performance and economic characteristics are included for each of the three system designs. Principal conclusions for each are highlighted and overall system comparisons and recommendations are set forth. (MHR)

Not Available

1977-04-01T23:59:59.000Z

89

Water-Loop Heat Pump Systems: Volumes 1 and 2  

Science Conference Proceedings (OSTI)

Water-loop heat pump (WLHP) systems are reliable, versatile, energy-efficient alternatives to conventional systems such as packaged rooftop or central chiller systems. These systems offer low installed costs, unparalleled design flexibility, and an inherent ability to recover heat in a variety of commercial and multifamily residential buildings for both new construction and retrofit markets.

1993-04-01T23:59:59.000Z

90

State energy price system. Volume II: data base development  

SciTech Connect

This volume documents the entire data development process in sufficient detail to permit critical assessment of the data base. However, since a methodological discussion is included in Chapter 3 of Volume I, it is not repeated here. The data base development process was conducted in a fuel-by-fuel fashion, following the general sequence of electricity, natural gas, coal, distillate fuel, motor gasoline, diesel, kerosene, jet fuel, residual fuel, and liquefied petroleum gas. For each of the fuels, a detailed data source review was conducted, which included a preliminary screening against criteria set up for this purpose. After this first screening, the data sources that met most of the review criteria were evaluated in more detail. If one data source met all the criteria, that data source was recommended for use, with minimal change or imputation. If there were substantial gaps in the available data series, then alternative imputation procedures were developed and compared, and recommendations were formulated. This entire procedure was then documented in a draft working paper for review and discussion. To the extent reasonable and practical, comments from the formal EIA reviews were then incorporated into the final recommendations and the data base was developed.

Fang, J.M.; Nieves, L.A.; Sherman, K.L.; Hood, L.J.

1982-06-01T23:59:59.000Z

91

System and method for radiation dose calculation within sub-volumes of a monte carlo based particle transport grid  

DOE Patents (OSTI)

A system and method is disclosed for radiation dose calculation within sub-volumes of a particle transport grid. In a first step of the method voxel volumes enclosing a first portion of the target mass are received. A second step in the method defines dosel volumes which enclose a second portion of the target mass and overlap the first portion. A third step in the method calculates common volumes between the dosel volumes and the voxel volumes. A fourth step in the method identifies locations in the target mass of energy deposits. And, a fifth step in the method calculates radiation doses received by the target mass within the dosel volumes. A common volume calculation module inputs voxel volumes enclosing a first portion of the target mass, inputs voxel mass densities corresponding to a density of the target mass within each of the voxel volumes, defines dosel volumes which enclose a second portion of the target mass and overlap the first portion, and calculates common volumes between the dosel volumes and the voxel volumes. A dosel mass module, multiplies the common volumes by corresponding voxel mass densities to obtain incremental dosel masses, and adds the incremental dosel masses corresponding to the dosel volumes to obtain dosel masses. A radiation transport module identifies locations in the target mass of energy deposits. And, a dose calculation module, coupled to the common volume calculation module and the radiation transport module, for calculating radiation doses received by the target mass within the dosel volumes.

Bergstrom, Paul M. (Livermore, CA); Daly, Thomas P. (Livermore, CA); Moses, Edward I. (Livermore, CA); Patterson, Jr., Ralph W. (Livermore, CA); Schach von Wittenau, Alexis E. (Livermore, CA); Garrett, Dewey N. (Livermore, CA); House, Ronald K. (Tracy, CA); Hartmann-Siantar, Christine L. (Livermore, CA); Cox, Lawrence J. (Los Alamos, NM); Fujino, Donald H. (San Leandro, CA)

2000-01-01T23:59:59.000Z

92

TPX: Contractor preliminary design review. Volume 2, PF systems engineering  

SciTech Connect

This system development specification covers the Poloidal Field (PF) Magnet System, WBS 14 in the Princeton Plasma Physics Laboratory TPX Program to build a tokamak fusion reactor. This specification establishes the performance, design, development and test requirements of the PF Magnet System.

Calvin, H.A. [Lawrence Livermore National Lab., CA (United States)

1995-07-28T23:59:59.000Z

93

A Management and Selection System for R&D Projects, Volume II - Project Management System and Project Data System  

DOE Green Energy (OSTI)

This report in three volumes describes an R&D project management and selection system developed for the Utilization Technology Branch of the Division of Geothermal Energy, Department of Energy. The proposed project management system (PMS) consists of a project data system (PDS) and a project selection procedure (PSP). The project data system consists of a series of project data forms and project status logs, and descriptions of information pathways. The PDS emphasizes timely monitoring of the technical and financial progress of projects, maintenance of the history of the project and rapid access to project information to facilitate responsive reporting to DGE and DOE upper management. The project selection procedure emphasizes an R&D product-oriented approach to benefit/cost analysis of individual projects. The report includes: (a) a description of the system, and recommendations for its implementation, (b) the PDS forms and an explanation of their use, (c) a glossary of terms for use on the forms, (d) a description of the benefit/cost approach, (e) a data base for estimating R&D benefits, and (f) examples of test applications of the system to nine current DGE projects. This volume discusses the proposed Project Data System in detail. It describes information needs and flow paths, and an information collection and storage system. Appendices contain the data forms for the system, and a glossary of terms and standard phrases for use on the forms.

Dhillon, Harpal S.; Entingh, Daniel J.

1978-05-01T23:59:59.000Z

94

Assessment of effectiveness of geologic isolation systems. CIRMIS data system. Volume 3. Generator routines  

SciTech Connect

The Assessment of Effectiveness of Geologic Isolation Systems (AEGIS) Program is developing and applying the methodology for assessing the far-field, long-term post-closure safety of deep geologic nuclear waste repositories. AEGIS is being performed by Pacific Northwest Laboratory (PNL) under contract with the Office of Nuclear Waste Isolation (ONWI) for the Department of Energy (DOE). One task within AEGIS is the development of methodology for analysis of the consequences (water pathway) from loss of repository containment as defined by various release scenarios. The various input parameters required in the analysis are compiled in data systems. The data are organized and prepared by various input subroutines for utilization by the hydraulic and transport codes. The hydrologic models simulate the groundwater flow systems and provide water flow directions, rates, and velocities as inputs to the transport models. Outputs from the transport models are basically graphs of radionuclide concentration in the groundwater plotted against time. After dilution in the receiving surface-water body (e.g., lake, river, bay), these data are the input source terms for the dose models, if dose assessments are required. The dose models calculate radiation dose to individuals and populations. CIRMIS (Comprehensive Information Retrieval and Model Input Sequence) Data System, a storage and retrieval system for model input and output data, including graphical interpretation and display is described. This is the third of four volumes of the description of the CIRMIS Data System.

Friedrichs, D.R.; Argo, R.S.

1980-01-01T23:59:59.000Z

95

Mechanically Cooled Large-Volume Germanium Detector Systems for Nuclear Explosion Monitoring DOENA27323-1  

SciTech Connect

Compact maintenance free mechanical cooling systems are being developed to operate large volume germanium detectors for field applications. To accomplish this we are utilizing a newly available generation of Stirling-cycle mechanical coolers to operate the very largest volume germanium detectors with no maintenance. The user will be able to leave these systems unplugged on the shelf until needed. The flip of a switch will bring a system to life in ~ 1 hour for measurements. The maintenance-free operating lifetime of these detector systems will exceed 5 years. These features are necessary for remote long-duration liquid-nitrogen free deployment of large-volume germanium gamma-ray detector systems for Nuclear Explosion Monitoring. The Radionuclide Aerosol Sampler/Analyzer (RASA) will greatly benefit from the availability of such detectors by eliminating the need for liquid nitrogen at RASA sites while still allowing the very largest available germanium detectors to be reliably utilized.

Hull, E.L.

2006-07-28T23:59:59.000Z

96

Economic development through biomass system integration. Volumes 2--4  

DOE Green Energy (OSTI)

Report documents a feasibility study for an integrated biomass power system, where an energy crop (alfalfa) is the feedstock for a processing plant and a power plant (integrated gasification combined cycle) in a way that benefits the facility owners.

DeLong, M.M.

1995-10-01T23:59:59.000Z

97

Integrated thermal treatment system study: Phase 1 results. Volume 1  

Science Conference Proceedings (OSTI)

An integrated systems engineering approach is used for uniform comparison of widely varying thermal treatment technologies proposed for management of contact-handled mixed low-level waste (MLLW) currently stored in the US Department of Energy complex. Ten different systems encompassing several incineration design options are studied. All subsystems, including facilities, equipment, and methods needed for integration of each of the ten systems are identified. Typical subsystems needed for complete treatment of MLLW are incoming waste receiving and preparation (characterization, sorting, sizing, and separation), thermal treatment, air pollution control, primary and secondary stabilization, metal decontamination, metal melting, mercury recovery, lead recovery, and special waste and aqueous waste treatment. The evaluation is performed by developing a preconceptual design package and planning life-cycle cost (PLCC) estimates for each system. As part of the preconceptual design process, functional and operational requirements, flow sheets and mass balances, and conceptual equipment layouts are developed for each system. The PLCC components estimated are technology development, production facility construction, pre-operation, operation and maintenance, and decontamination and decommissioning. Preconceptual design data and other technology information gathered during the study are examined and areas requiring further development, testing, and evaluation are identified and recommended. Using a qualitative method, each of the ten systems are ranked.

Feizollahi, F.; Quapp, W.J.; Hempill, H.G.; Groffie, F.J.

1994-07-01T23:59:59.000Z

98

Evaluation of line focus solar central power systems. Volume II. Systems evaluation  

DOE Green Energy (OSTI)

An evaluation was completed to ascertain the applicability of line focus technologies to electrical power applications and to compare their performance and cost potential with point focus central receiver power systems. It was concluded that although the high temperature line focus (SRI) and fixed mirror line focus (GA) concepts duplicate the heat source characteristics and power conversion technology of the central receiver concepts these configurations do not offer a sufficient improvement in cost to warrant full scale development. The systems are, however, less complex than their point focus counterpart and should the central receiver system development falter they provide reasonable technology alternatives. The parabolic trough concept (BDM) was found to provide a low temperature technology alternative to the central receiver concept with promising performance and cost potential. Its continued development is recommended, with special emphasis on lower temperature (< 700/sup 0/F) applications. Finally, a variety of new promising line focus power system configurations were identified for a range of utility and industrial applications and recommendations were made on their implementation. This volume contains the detailed report. (WHK)

Not Available

1980-03-15T23:59:59.000Z

99

Conceptual design and systems analysis of photovoltaic power systems. Volume II. Systems. Revised final report  

DOE Green Energy (OSTI)

Conceptual designs were made and analyses were performed on three types of solar photovoltaic power systems. Included were Residential (1--10 kW), Intermediate (0.1--10 MW), and Central (50--1000 MW) Power Systems to be installed in the 1985 to 2000 time period. Detailed descriptions of each of the three systems studied, descriptions of the necessary subsystems, and discussions of the interfaces between them are presented. Included also are descriptions of system performance and system cost used to perform an economic analysis which assesses the value of each system.

Pittman, P.F.

1977-03-01T23:59:59.000Z

100

Combined cycle solar central receiver hybrid power system study. Volume III. Appendices. Final technical report  

DOE Green Energy (OSTI)

A design study for a 100 MW gas turbine/steam turbine combined cycle solar/fossil-fuel hybrid power plant is presented. This volume contains the appendices: (a) preconceptual design data; (b) market potential analysis methodology; (c) parametric analysis methodology; (d) EPGS systems description; (e) commercial-scale solar hybrid power system assessment; and (f) conceptual design data lists. (WHK)

None

1979-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Road Transportable Analytical Laboratory (RTAL) system: Volume I. Final report  

Science Conference Proceedings (OSTI)

This report describes a portable laboratory system for the analysis of soils, ground water, and surface waters for the detection and quantification of hazardous materials, organics, and radioactive contaminants. The goal of the Road Transportable Analytical Laboratory (RTAL) is a sample throughput of 20 samples per day, providing a full range of analysis on each sample within 16 hours of preparation with high accuracy.

Finger, S.M.; De Avila, J.C.; Keith, V.F.

1996-08-01T23:59:59.000Z

102

Nuclear proliferation and civilian nuclear power. Report of the Nonproliferation Alternative Systems Assessment Program. Volume I. Program summary  

SciTech Connect

This report summarizes the Nonproliferation Alternative Systems Assessment Program (NASAP): its background, its studies, and its results. The introductory chapter traces the growth of the issue of nuclear weapons proliferation and the organization and objectives of NASAP. Chapter 2 summarizes the program's assessments, findings, and recommendations. Each of Volumes II-VII reports on an individual assessment (Volumn II: Proliferation Resistance; Volume III: Resources and Fuel Cycle Facilities; Volume IV: Commercial Potential; Volume V: Economics and Systems Analysis; Volume VI: Safety and Environmental Considerations for Licensing; Volume VII: International Perspectives). Volume VIII (Advanced Concepts) presents a combined assessment of several less fully developed concepts, and Volume IX (Reactor and Fuel Cycle Descriptions) provides detailed descriptions of the reactor and fuel-cycle systems studied by NASAP.

Not Available

1980-06-01T23:59:59.000Z

103

Progress in passive solar energy systems. Volume 8. Part 1  

DOE Green Energy (OSTI)

This book presents the papers given at a conference sponsored by the US DOE, the Solar Energy Research Institute, SolarVision, Inc., and the Southern California Solar Energy Society. The topics considered at the conference included sizing solar energy systems for agricultural applications, a farm scale ethanol production plant, the EEC wind energy RandD program, the passive solar performance assessment of an earth-sheltered house, the ARCO 1 MW photovoltaic power plant, the performance of a dendritic web photovoltaic module, second generation point focused concentrators, linear fresnel lens concentrating photovoltaic collectors, photovoltaic conversion efficiency, amorphous silicon thin film solar cells, a photovoltaic system for a shopping center, photovoltaic power generation for the utility industry, spectral solar radiation, and the analysis of insolation data.

Hayes, J.; Andrejko, D.A.

1983-01-01T23:59:59.000Z

104

Conversion system overview assessment. Volume 1: solar thermoelectrics  

DOE Green Energy (OSTI)

An assessment of thermoelectrics for solar energy conversion is given. There is significant potential for solar thermoelectrics in solar technologies where collector costs are low; e.g., Ocean Thermal Energy Conversion (OTEC) and solar ponds. Reports of two studies by manufacturers assessing the cost of thermoelectric generators in large scale production are included in the appendix and several new concepts thermoelectric systems are presented. (WHK)

Jayadev, T. S.; Henderson, J.; Finegold, J.; Benson, D.

1979-08-01T23:59:59.000Z

105

RELAP5/MOD3 code manual: Code structure, system models, and solution methods. Volume 1  

Science Conference Proceedings (OSTI)

The RELAP5 code has been developed for best estimate transient simulation of light water reactor coolant systems during postulated accidents. The code models the coupled behavior of the reactor coolant system and the core for loss-of-coolant accidents, and operational transients, such as anticipated transient without scram, loss of offsite power, loss of feedwater, and loss of flow. A generic modeling, approach is used that permits simulating a variety of thermal hydraulic systems. Control system and secondary system components are included to permit modeling of plant controls, turbines, condensers, and secondary feedwater systems. RELAP5/MOD3 code documentation is divided into seven volumes: Volume I provides modeling theory and associated numerical schemes.

NONE

1995-08-01T23:59:59.000Z

106

Mechanically Cooled Large-Volume Germanium Detector Systems for Neclear Explosion Monitoring DOENA27323-2  

Science Conference Proceedings (OSTI)

Compact maintenance free mechanical cooling systems are being developed to operate large volume high-resolution gamma-ray detectors for field applications. To accomplish this we are utilizing a newly available generation of Stirling-cycle mechanical coolers to operate the very largest volume germanium detectors with no maintenance. The user will be able to leave these systems unplugged on the shelf until needed. The maintenance-free operating lifetime of these detector systems will exceed 5 years. Three important factors affect the operation of mechanically cooled germanium detectors: temperature, vacuum, and vibration. These factors will be studied in the laboratory at the most fundamental levels to insure a solid understanding of the physical limitations each factor places on a practical mechanically cooled germanium detector system. Using this knowledge, mechanically cooled germanium detector prototype systems will be designed and fabricated.

Hull, E.L.

2006-10-30T23:59:59.000Z

107

Solar Pilot Plant, Phase I. Preliminary design report. Volume II. System description and system analysis. CDRL item 2  

DOE Green Energy (OSTI)

Honeywell conducted a parametric analysis of the 10-MW(e) solar pilot plant requirements and expected performance and established an optimum system design. The main analytical simulation tools were the optical (ray trace) and the dynamic simulation models. These are described in detail in Books 2 and 3 of this volume under separate cover. In making design decisions, available performance and cost data were used to provide a design reflecting the overall requirements and economics of a commercial-scale plant. This volume contains a description of this analysis/design process and resultant system/subsystem design and performance.

None

1977-05-01T23:59:59.000Z

108

System 80+{trademark} Standard Design: CESSAR design certification. Volume 4: Amendment I  

Science Conference Proceedings (OSTI)

This report, entitled Combustion Engineering Standard Safety Analysis Report - Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These documents describe the Combustion Engineering, Inc. System 80+{sup TM} Standard Design. This report, Volume 4, provides a description of the reactor, reactor internals, fuel assemblies, and associated design requirements.

Not Available

1990-12-21T23:59:59.000Z

109

Systems Engineering Management Plan. Volume 5 of the MRS Project Management Plan  

SciTech Connect

The purpose of this Monitored Retrievable Storage (MRS) Project Systems Engineering Management Plan (SEMP) is to define and establish the MRS Project Systems Engineering process that implements the approved policy and requirements of the Office of Civilian Radioactive Waste Management (OCRWM) for the US Department of Energy (DOE). This plan is Volume 5 of the MRS Project Management Plan (PMP). This plan provides the framework for implementation of systems engineering on the MRS Project consistent with DOE Order 4700.1, the OCRWM Program Management System Manual (PMSM), and the OCRWM Systems Engineering Management Plan (SEMP).

1994-01-01T23:59:59.000Z

110

Conversion system overview assessment. Volume III. Solar thermal/coal or biomass derived fuels  

SciTech Connect

The three volumes of this report cover three distinct areas of solar energy research: solar thermoelectrics, solar-wind hybrid systems, and synthetic fuels derived with solar thermal energy. Volume III deals with the conversion of synthetic fuels with solar thermal heat. The method is a hybrid combination of solar energy with either coal or biomass. A preliminary assessment of this technology is made by calculating the cost of fuel produced as a function of the cost of coal and biomass. It is shown that within the projected ranges of coal, biomass, and solar thermal costs, there are conditions when solar synthetic fuels with solar thermal heat will become cost-competitive.

Copeland, R. J.

1980-02-01T23:59:59.000Z

111

Model documentation Natural Gas Transmission and Distribution Model of the National Energy Modeling System. Volume 1  

Science Conference Proceedings (OSTI)

The Natural Gas Transmission and Distribution Model (NGTDM) of the National Energy Modeling System is developed and maintained by the Energy Information Administration (EIA), Office of Integrated Analysis and Forecasting. This report documents the archived version of the NGTDM that was used to produce the natural gas forecasts presented in the Annual Energy Outlook 1996, (DOE/EIA-0383(96)). The purpose of this report is to provide a reference document for model analysts, users, and the public that defines the objectives of the model, describes its basic approach, and provides detail on the methodology employed. Previously this report represented Volume I of a two-volume set. Volume II reported on model performance, detailing convergence criteria and properties, results of sensitivity testing, comparison of model outputs with the literature and/or other model results, and major unresolved issues.

NONE

1996-02-26T23:59:59.000Z

112

Technical specifications manual for the MARK-1 pulsed ionizing radiation detection system. Volume 1  

Science Conference Proceedings (OSTI)

The MARK-1 detection system was developed by the Idaho National Engineering Laboratory for the US Department of Energy Office of Arms Control and Nonproliferation. The completely portable system was designed for the detection and analysis of intense photon emissions from pulsed ionizing radiation sources. This manual presents the technical design specifications for the MARK-1 detection system and was written primarily to assist the support or service technician in the service, calibration, and repair of the system. The manual presents the general detection system theory, the MARK-1 component design specifications, the acquisition and control software, the data processing sequence, and the system calibration procedure. A second manual entitled: Volume 2: Operations Manual for the MARK-1 Pulsed Ionizing Radiation Detection System (USDOE Report WINCO-1108, September 1992) provides a general operational description of the MARK-1 detection system. The Operations Manual was written primarily to assist the field operator in system operations and analysis of the data.

Lawrence, R.S.; Harker, Y.D.; Jones, J.L.; Hoggan, J.M.

1993-03-01T23:59:59.000Z

113

Simulation model for wind energy storage systems. Volume III. Program descriptions. [SIMWEST CODE  

DOE Green Energy (OSTI)

The effort developed a comprehensive computer program for the modeling of wind energy/storage systems utilizing any combination of five types of storage (pumped hydro, battery, thermal, flywheel and pneumatic). An acronym for the program is SIMWEST (Simulation Model for Wind Energy Storage). The level of detail of SIMWEST is consistent with a role of evaluating the economic feasibility as well as the general performance of wind energy systems. The software package consists of two basic programs and a library of system, environmental, and load components. Volume III, the SIMWEST program description contains program descriptions, flow charts and program listings for the SIMWEST Model Generation Program, the Simulation program, the File Maintenance program and the Printer Plotter program. Volume III generally would not be required by SIMWEST user.

Warren, A.W.; Edsinger, R.W.; Burroughs, J.D.

1977-08-01T23:59:59.000Z

114

Simulation model for wind energy storage systems. Volume II. Operation manual. [SIMWEST code  

DOE Green Energy (OSTI)

The effort developed a comprehensive computer program for the modeling of wind energy/storage systems utilizing any combination of five types of storage (pumped hydro, battery, thermal, flywheel and pneumatic). An acronym for the program is SIMWEST (Simulation Model for Wind Energy Storage). The level of detail of SIMWEST is consistent with a role of evaluating the economic feasibility as well as the general performance of wind energy systems. The software package consists of two basic programs and a library of system, environmental, and load components. Volume II, the SIMWEST operation manual, describes the usage of the SIMWEST program, the design of the library components, and a number of simple example simulations intended to familiarize the user with the program's operation. Volume II also contains a listing of each SIMWEST library subroutine.

Warren, A.W.; Edsinger, R.W.; Burroughs, J.D.

1977-08-01T23:59:59.000Z

115

Utility FGD survey: January--December 1989. Volume 1, Categorical summaries of FGD systems  

SciTech Connect

This is Volume 1 of the Utility flue gas desulfurization (FGD) Survey report, which is generated by a computerized data base management system, represents a survey of operational and planned domestic utility flue gas desulfurization (FGD) systems. It summarizes information contributed by the utility industry, system and equipment suppliers, system designers, research organizations, and regulatory agencies. The data cover system design, fuel characteristics, operating history, and actual system performance. Also included is a unit-by-unit discussion of problems and solutions associated with the boilers, scrubbers, and FGD systems. The development status (operational, under construction, or in the planning stages), system supplier, process, waste disposal practice, and regulatory class are tabulated alphabetically by utility company.

Hance, S.L.; McKibben, R.S.; Jones, F.M.

1992-03-01T23:59:59.000Z

116

Assessment of solar options for small power systems applications. Volume IV. Comparative ranking of concepts  

DOE Green Energy (OSTI)

A comparative analysis of solar thermal conversion concepts that are potentially suitable for development as small electric power systems (1 to 10 MWe) is presented. Cogeneration and total energy systems were beyond the scope of this study. Seven generic type of collectors, together with associated subsystems for electric power generation, were considered. The collectors can be classified into three categories: (1) two-axis tracking (with compound-curvature reflecting surfaces); (2) one-axis tracking (with single-curvature reflecting surfaces; and (3) nontracking (with low-concentration reflecting surfaces). All seven collectors were analyzed in conceptual system configurations with Rankine-cycle engines. In addition, two of the collectors (the Point Focus Central Receiver and the Point Focus Distributed Receiver) were analyzed with Brayton-cycle engines, and the latter of the two also was analyzed with Stirling-cycle engines. With these engine options, 10 systems were formulated for analysis. This is the fourth volume of a five-volume report on the work performed to analyze the alternative concepts, and the results obtained. Included in this volume are descriptions of the methodology used with, and concept ranks obtained from, potential users and R and D fund allocators.

Currie, J.W.; Jannol, M.

1980-07-01T23:59:59.000Z

117

Ocean thermal energy conversion power system development-I. Volume 4. Appendix G. Preliminary design report  

DOE Green Energy (OSTI)

The conceptual design of a 40 to 50 MW closed cycle ammonia OTEC commercial plant, the preliminary design of a 10 MW OTEC module analogous to the 50 MW module, and the preliminary design of heat exchanger test articles (evaporator and condenser) representative of the 50 MW heat exchangers for testing in OTEC-1 are presented. This volume of the report presents Appendix G: ammonia cycle, auxiliaries and ancillaries. Design descriptions are given (for the 50 MW commercial plant and the 10 MW module) for the ammonia vapor and condensate systems, ammonia storage and fill systems, noncondensible gas removal systems, ammonia cleanup systems, ammonia unloading systems, leak detection systems, and fluid sampling systems. (WHK)

Not Available

1978-12-18T23:59:59.000Z

118

Evaluation of line focus solar central power systems. Volume I. Executive summary  

DOE Green Energy (OSTI)

An evaluation was completed to ascertain the applicability of line focus technologies to electrical power applications and to compare their performance and cost potential with point focus central receiver power systems. It was concluded that although the high temperature line focus (SRI) and fixed mirror line focus (GA) concepts duplicate the heat source characteristics and power conversion technology of the central receiver concepts these configurations do not offer a sufficient improvement in cost to warrant full scale development. The systems are, however, less complex than their point focus counterpart and should the central receiver system development falter they provide reasonable technology alternatives. This volume is an executive summary. (WHK)

Not Available

1980-03-15T23:59:59.000Z

119

Deep Drilling Basic Research: Volume 5 - System Evaluations. Final Report, November 1988--August 1990  

Science Conference Proceedings (OSTI)

This project is aimed at decreasing the costs and increasing the efficiency of drilling gas wells in excess of 15,000 feet. This volume presents a summary of an evaluation of various drilling techniques. Drilling solutions were compared quantitatively against typical penetration rates derived from conventional systems. A qualitative analysis measured the impact of a proposed system on the drilling industry. The evaluations determined that the best candidates f o r improving the speed and efficiency of drilling deep gas wells include: PDC/TSD bits, slim-hole drilling, roller-cone bits, downhole motors, top-driven systems, and coiled-tubing drilling.

None

1990-06-01T23:59:59.000Z

120

Simulation model for wind energy storage systems. Volume I. Technical report. [SIMWEST code  

SciTech Connect

The effort developed a comprehensive computer program for the modeling of wind energy/storage systems utilizing any combination of five types of storage (pumped hydro, battery, thermal, flywheel and pneumatic). An acronym for the program is SIMWEST (Simulation Model for Wind Energy Storage). The level of detail of SIMWEST is consistent with a role of evaluating the economic feasibility as well as the general performance of wind energy systems. The software package consists of two basic programs and a library of system, environmental, and load components. Volume I gives a brief overview of the SIMWEST program and describes the two NASA defined simulation studies.

Warren, A.W.; Edsinger, R.W.; Chan, Y.K.

1977-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Field testing of component-level model-based fault detection methods for mixing boxes and VAV fan systems  

E-Print Network (OSTI)

based methods of fault detection and diagnosis (FDD).Component-level FDD, which is the subject of the work

Xu, Peng; Haves, Philip

2002-01-01T23:59:59.000Z

122

Field testing of component-level model-based fault detection methods for mixing boxes and VAV fan systems  

E-Print Network (OSTI)

precluded testing the fan based on design data. Since thisStatic Pressure (inWg) fan CFM SF-SP SF-SP-Design-Sim time (supply fan pressure rise) SF- DP SF-DP-Design-simulated D.

Xu, Peng; Haves, Philip

2002-01-01T23:59:59.000Z

123

Field testing of component-level model-based fault detection methods for mixing boxes and VAV fan systems  

E-Print Network (OSTI)

measurement of airflow rate. Supply fan speed (0-1) SA S.A.Supply Fan test S.B.Fan pressure rise calibration SF-DP-Simulated Pressure

Xu, Peng; Haves, Philip

2002-01-01T23:59:59.000Z

124

Field testing of component-level model-based fault detection methods for mixing boxes and VAV fan systems  

E-Print Network (OSTI)

and diagnosis for cooling towers. ASHRAE Trans. , vol.107,of faults in the cooling tower circuit of a central chilled

Xu, Peng; Haves, Philip

2002-01-01T23:59:59.000Z

125

W-320 waste retrieval sluicing system transfer line flushing volume and frequency calculation  

DOE Green Energy (OSTI)

The calculations contained in this analysis document establish the technical basis for the volume, frequency, and flushing fluid to be utilized for routine Waste Retrieval Sluicing System (WRSS) process line flushes. The WRSS was installed by Project W-320, Tank 241-C-106 Sluicing. The double contained pipelines being flushed have 4 inch stainless steel primary pipes. The flushes are intended to prevent hydrogen buildup in the transfer lines and to provide ALARA conditions for maintenance personnel.

Bailey, J.W.

1997-04-07T23:59:59.000Z

126

W-320 waste retrieval sluicing system transfer line flushing volume and frequency calculation  

DOE Green Energy (OSTI)

The calculations contained in this analysis document establish the technical basis for the volume, frequency, and flushing fluid to be utilized for routine Waste Retrieval Sluicing System (WRSS) process line flushes. The WRSS was installed by Project W-320, Tank 24 I-C-106 Sluicing. The double contained pipelines being flushed have 4 inch stainless steel primary pipes. The flushes are intended to prevent hydrogen build up in the transfer lines and to provide ALARA conditions for maintenance personnel.

Bailey, J.W.

1997-11-05T23:59:59.000Z

127

INVESTIGATION OF MAGNETOHYDRODYNAMIC POWER GENERATION. VOLUME I. SYSTEM ANALYSIS AND ENVIRONMENTAL TESTING. Final Report  

SciTech Connect

A system analysis was performed to establish the design and performance characteristics of 250- and 1000-Mev MHD generators. The results are presented, and the necessary equations are derived. The results of environmental tests that investigated boundary and bulk conductivity, structural concepts, and combustion phenomena are included. The other five volumes of the report are summarized, together with the principal conclusions. (D.C.W.)

1963-05-01T23:59:59.000Z

128

Preliminary environmental assessment for the Satellite Power System (SPS). Revision 1. Volume 2. Detailed assessment  

DOE Green Energy (OSTI)

The Department of Energy (DOE) is considering several options for generating electrical power to meet future energy needs. The satellite power system (SPS), one of these options, would collect solar energy through a system of satellites in space and transfer this energy to earth. A reference system has been described that would convert the energy to microwaves and transmit the microwave energy via directive antennas to large receiving/rectifying antennas (rectennas) located on the earth. At the rectennas, the microwave energy would be converted into electricity. The potential environmental impacts of constructing and operating the satellite power system are being assessed as a part of the Department of Energy's SPS Concept Development and Evaluation Program. This report is Revision I of the Preliminary Environmental Assessment for the Satellite Power System published in October 1978. It refines and extends the 1978 assessment and provides a basis for a 1980 revision that will guide and support DOE recommendations regarding future SPS development. This is Volume 2 of two volumes. It contains the technical detail suitable for peer review and integrates information appearing in documents referenced herein. The key environmental issues associated with the SPS concern human health and safety, ecosystems, climate, and electromagnetic systems interactions. In order to address these issues in an organized manner, five tasks are reported: (I) microwave-radiation health and ecological effects; (II) nonmicrowave health and ecological effectss; (III) atmospheric effects; (IV) effects on communication systems due to ionospheric disturbance; and (V) electromagnetic compatibility. (WHK)

Not Available

1980-01-01T23:59:59.000Z

129

Deep Drilling Basic Research: Volume 4 - System Description. Final Report, November 1988--August 1990  

DOE Green Energy (OSTI)

The first section of this Volume will discuss the ''Conventional Drilling System''. Today's complex arrangement of numerous interacting systems has slowly evolved from the very simple cable tool rigs used in the late 1800s. Improvements to the conventional drilling rig have varied in size and impact over the years, but the majority of them have been evolutionary modifications. Each individual change or improvement of this type does not have significant impact on drilling efficiency and economics. However, the change is almost certain to succeed, and over time--as the number of evolutionary changes to the system begin to add up--improvements in efficiency and economics can be seen. Some modifications, defined and described in this Volume as Advanced Modifications, have more than just an evolutionary effect on the conventional drilling system. Although the distinction is subtle, there are several examples of incorporated advancements that have had significantly more impact on drilling procedures than would a truly evolutionary improvement. An example of an advanced modification occurred in the late 1970s with the introduction of Polycrystalline Diamond Compact (PDC) drill bits. PDC bits resulted in a fundamental advancement in drilling procedures that could not have been accomplished by an evolutionary improvement in materials metallurgy, for example. The last drilling techniques discussed in this Volume are the ''Novel Drilling Systems''. The extent to which some of these systems have been developed varies from actually being tested in the field, to being no more than a theoretical concept. However, they all have one thing in common--their methods of rock destruction are fundamentally different from conventional drilling techniques. When a novel drilling system is introduced, it is a revolutionary modification of accepted drilling procedures and will completely replace current techniques. The most prominent example of a revolutionary modification in recent history was the complete displacement of cable tool rigs by rotary drilling rigs in the late 1920s.

Anderson, E.E.; Maurer, W.C.; Hood, M.; Cooper, G.; Cook, N.

1990-06-01T23:59:59.000Z

130

Kilowatt isotope power system phase II plan. Volume II: flight System Conceptual Design (FSCD)  

SciTech Connect

The Kilowatt Isotope Power System (KIPS) Flight System Conceptual Design (FSCD) is described. Included are a background, a description of the flight system conceptual design, configuration of components, flight system performance, Ground Demonstration System test results, and advanced development tests.

1978-03-01T23:59:59.000Z

131

Solar/hydrogen systems for the 1985 to 2000 time frame. Volume I. Solar/hydrogen systems assessment. Final report  

DOE Green Energy (OSTI)

The findings of a study of opportunities for commercialization of systems capable of producing hydrogen from solar energy are presented in two volumes. A compendium of monographs by specialists in the fields of solar energy conversion technologies, hydrogen production technologies and related technology descriptions from the general literature comprise Volume II. This data base was used to support an evaluation and selection process that identified four candidate solar/hydrogen systems best suited to commercialization within the next two decades. Volume I first reviews the background of the work and the methods used. Then an evaluation of the hydrogen product costs that might be achieved by the four selected candidate systems (photovoltaic/water electrolysis, thermal-heat engine/water electrolysis, wind energy/water electrolysis, small hydrogen/water electrolysis) is compared with the pricing structure and practices of the commodity gas market. Subsequently, product cost and market price match is noted to exist in the small user sector of the hydrogen marketplace. Barriers to and historical time lags in, commercialization of new technologies are then reviewed. Finally, recommendations for development and demonstration programs designed to accelerate the commercialization of the candidate systems are presented.

Foster, R. W.; Tison, R. R.; Escher, W. J.D.; Hanson, J. A.

1980-06-01T23:59:59.000Z

132

Research on Fuzzy Regulation Strategies in the Constant Air Volume Air Conditioning System  

E-Print Network (OSTI)

The energy consumption of the constant air volume (CAV) system largely depends on the regulation strategies. Although some air conditioning systems are equipped with automatic regulation devices, others lack effective regulation strategies. To avoid wasting energy and presenting simple regulation methods, fuzzy regulation strategies for CAV systems are studied in this research. A CAV system of an office building is modeled and simulated with the Designer's Simulation Toolkit (DeST). The operating parameters are calculated based on the instantaneous load obtained from simulation. The operation of the system is divided into five stages according to different conception of cold or hot in different seasons. The relationship between the outdoor air temperature and the fresh air volume, and the supply air temperature is presented in the form of fuzzy rules. Then the building is simulated under different load conditions and the operating parameters are obtained from fuzzy reasoning. Finally, the effect of fuzzy strategies on energy consumption is analyzed and compared with the effects of the operating parameters obtained from simulation. The results show that energy consumption using a fuzzy regulation strategy is close to the energy consumption of knowing the exact load of the building, while the fuzzy regulation strategy can largely simplify the regulation of the air conditioning system.

Bai, T.; Zhang, J.; Ning, N.; Tong, K.; Wu, Y.; Wang, H.

2006-01-01T23:59:59.000Z

133

Proceedings of the Advanced Turbine Systems Annual Program Review meeting. Volume 1  

DOE Green Energy (OSTI)

Goal of the 8-year program is to develop cleaner, more efficient, and less expensive gas turbine systems for utility and industrial electric power generation, cogeneration, and mechanical drive units. The conference is held annually for energy executives, engineers, scientists, and other interested parties industry, academia, and Government. Advanced turbine systems topics discussed during five technical sessions included policy and strategic issues, program element overviews and technical reviews, related activities, university/industry consortium interactions, and supportive projects. Twenty-one papers presented during the technical sessions are contained in this volume; they are processed separately for the data base.

NONE

1995-10-01T23:59:59.000Z

134

Community Energy Systems and the Law of Public Utilities. Volume Fifty. West Virginia  

SciTech Connect

A detailed description is presented of the laws and programs of the State of West Virginia governing the regulation of public energy utilities, the siting of energy generating and transmission facilities, the municipal franchising of public energy utilities, and the prescription of rates to be charged by utilities including attendant problems of cost allocations, rate base and operating expense determinations, and rate of return allowances. These laws and programs are analyzed to identify impediments which they may present to the implementation of Integrated Community Energy Systems (ICES). This report is one of fifty-one separate volumes which describe such regulatory programs at the Federal level and in each state as background to the report entitled Community Energy Systems and the Law of Public Utilities - Volume One: An Overview. This report also contains a summary of a strategy described in Volume One - An Overview for overcoming these impediments by working within the existing regulatory framework and by making changes in the regulatory programs to enhance the likelihood of ICES implementation.

Feurer, D.A.; Weaver, C.L.

1981-01-01T23:59:59.000Z

135

Community Energy Systems and the Law of Public Utilities. Volume Forty-nine. Washington  

SciTech Connect

A detailed description is presented of the laws and programs of the State of Washington governing the regulation of public energy utilities, the siting of energy generating and transmission facilities, the municipal franchising of public energy utilities, and the prescription of rates to be charged by utilities including attendant problems of cost allocations, rate base and operating expense determinations, and rate of return allowances. These laws and programs are analyzed to identify impediments which they may present to the implementation of Integrated Community Energy Systems (ICES). This report is one of fifty-one separate volumes which describe such regulatory programs at the Federal level and in each state as background to the report entitled Community Energy Systems and the Law of Public Utilities - Volume One: An Overview. This report also contains a summary of a strategy described in Volume One - An Overview for overcoming these impediments by working within the existing regulatory framework and by making changes in the regulatory programs to enhance the likelihood of ICES implementation.

Feurer, D.A.; Weaver, C.L.

1981-01-01T23:59:59.000Z

136

Solar Central Receiver Hybrid Power Systems sodium-cooled receiver concept. Final report. Volume III. Appendices  

DOE Green Energy (OSTI)

The overall, long term objective of the Solar Central Receiver Hybrid Power System is to identify, characterize, and ultimately demonstrate the viability and cost effectiveness of solar/fossil, steam Rankine cycle, hybrid power systems that: (1) consist of a combined solar central receiver energy source and a nonsolar energy source at a single, common site, (2) may operate in the base, intermediate, and peaking capacity modes, (3) produce the rated output independent of variations in solar insolation, (4) provide a significant savings (50% or more) in fuel consumpton, and (5) produce power at the minimum possible cost in mills/kWh. It is essential that these hybrid concepts be technically feasible and economically competitive with other systems in the near to mid-term time period (1985-1990) on a commercial scale. The program objective for Phase I is to identify and conceptually characterize solar/fossil steam Rankine cycle, commercial-scale, power plant systems that are economically viable and technically feasible. This volume contains appendices to the conceptual design and systems analysis studies gien in Volume II, Books 1 and 2. (WHK)

None

1980-01-01T23:59:59.000Z

137

Control Humidity With Single-Duct, Single-Zone, Constant Air Volume System  

E-Print Network (OSTI)

The lecture hall of the Richardson Petroleum Building at Texas A&M University is a large lecture hall, with a total floor area of approximately 2500 ft^2. The lecture hall was served by a constant air volume (CAV) air handling unit (AHU) which had no reheat coil. This resulted in high room humidity levels although the room temperature was satisfied for part load conditions, especially when there was very little sensible load from the room. This paper presents Continuous Commissioning efforts (CC), which turned this inefficient, humid lecture hall into a comfortable learning environment. This case study also explores other possibilities to solve the humidity control problem with single-duct, single-zone constant air volume systems.

Chen, H.; Deng, S.; Bruner, H. L.; Claridge, D. E.

2000-01-01T23:59:59.000Z

138

Electric and Hybrid Vehicle System Research and Development Project: Hybrid Vehicle Potential Assessment. Volume 1. Summary  

DOE Green Energy (OSTI)

The results of investigations conducted under Ce Hybrid Vehicle Potential Assessment Task are reported in 10 volumes. This volume contains an overview of the study and its results. The purpose of the overall study was to determine if the petroleum fuel savings achievable through the use of hybrid electric vehicles is worth the R and D expenditures needed to develop the hybrid vehicles and to determine R and D priorities. It was concluded that by the year 2010 hybrid vehicles could replace 80% of the automotive power that would otherwise be produced from petroleum fuels; the public should not suffer any mobility loss through the use of hybrid vehicles; high initial and life-cycle costs are a limiting factor; and R and D funds should be spent for systems design and the development of low-cost batteries and controllers. (LCL)

Surber, F.T.

1979-09-30T23:59:59.000Z

139

Model documentation: Natural Gas Transmission and Distribution Model of the National Energy Modeling System; Volume 1  

SciTech Connect

The Natural Gas Transmission and Distribution Model (NGTDM) is a component of the National Energy Modeling System (NEMS) used to represent the domestic natural gas transmission and distribution system. NEMS is the third in a series of computer-based, midterm energy modeling systems used since 1974 by the Energy Information Administration (EIA) and its predecessor, the Federal Energy Administration, to analyze domestic energy-economy markets and develop projections. This report documents the archived version of NGTDM that was used to produce the natural gas forecasts used in support of the Annual Energy Outlook 1994, DOE/EIA-0383(94). The purpose of this report is to provide a reference document for model analysts, users, and the public that defines the objectives of the model, describes its basic design, provides detail on the methodology employed, and describes the model inputs, outputs, and key assumptions. It is intended to fulfill the legal obligation of the EIA to provide adequate documentation in support of its models (Public Law 94-385, Section 57.b.2). This report represents Volume 1 of a two-volume set. (Volume 2 will report on model performance, detailing convergence criteria and properties, results of sensitivity testing, comparison of model outputs with the literature and/or other model results, and major unresolved issues.) Subsequent chapters of this report provide: (1) an overview of the NGTDM (Chapter 2); (2) a description of the interface between the National Energy Modeling System (NEMS) and the NGTDM (Chapter 3); (3) an overview of the solution methodology of the NGTDM (Chapter 4); (4) the solution methodology for the Annual Flow Module (Chapter 5); (5) the solution methodology for the Distributor Tariff Module (Chapter 6); (6) the solution methodology for the Capacity Expansion Module (Chapter 7); (7) the solution methodology for the Pipeline Tariff Module (Chapter 8); and (8) a description of model assumptions, inputs, and outputs (Chapter 9).

NONE

1994-02-24T23:59:59.000Z

140

Assessment of LWR spent fuel disposal options. Volume 3. Study bases and system design considerations (Appendices). Technical report  

SciTech Connect

Volume 3 (Appendices) provides a tabulation of the bases and assumptions used in the study as well as preconceptual design description and cost estimates of the facilities and transportation systems necessary to implement the various study cases.

1979-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Turbine Generator Auxiliary Systems Volume 1: Turbine Generator Lubrication System Maintenance Guide -- 2012 Update  

Science Conference Proceedings (OSTI)

This report provides nuclear and fossil plant personnel with current maintenance information on lubrication system components and specifications, treatment, and analysis of the lubricating oil.BackgroundInput from member utilities indicated that maintenance guides were needed for the turbine-generator auxiliary systems. The first auxiliary system selected was the turbine-generator lubrication system used in nuclear and ...

2012-12-12T23:59:59.000Z

142

Steam Turbine Generator Auxiliary System Maintenance Guide--Volume 7 (Generator Excitation System)  

Science Conference Proceedings (OSTI)

Excitation systems are a critical part of the power generation system. They must be capable of providing a reliable excitation current to the generator and respond to system fluctuations while maintaining consistent generator voltage and power factor. Most modern excitation systems use a static or rotating solid-state exciter and include the associated components required to provide regulation and control over voltage and reactive power flow and to enhance power system stability. The proper operation of ...

2011-12-23T23:59:59.000Z

143

Transportation Sector Model of the National Energy Modeling System. Volume 2 -- Appendices: Part 1  

Science Conference Proceedings (OSTI)

This volume contains input data and parameters used in the model of the transportation sector of the National Energy Modeling System. The list of Transportation Sector Model variables includes parameters for the following: Light duty vehicle modules (fuel economy, regional sales, alternative fuel vehicles); Light duty vehicle stock modules; Light duty vehicle fleet module; Air travel module (demand model and fleet efficiency model); Freight transport module; Miscellaneous energy demand module; and Transportation emissions module. Also included in these appendices are: Light duty vehicle market classes; Maximum light duty vehicle market penetration parameters; Aircraft fleet efficiency model adjustment factors; and List of expected aircraft technology improvements.

NONE

1998-01-01T23:59:59.000Z

144

Assessment of solar options for small power systems applications. Volume III. Analysis of concepts  

DOE Green Energy (OSTI)

A comparative analysis of solar thermal conversion concepts that are potentially suitable for development as small electric power systems (1 to 10 MWe) is given. Seven generic types of collectors, together with associated subsystems for electric power generation, were considered. The collectors can be classified into three categories: (1) two-axis tracking (with compound-curvature reflecting surfaces; (2) one-axis tracking (with single-curvature reflecting suraces; and (3) nontracking (with low-concentration reflecting surfaces). All seven collectors were analyzed in conceptual system configurations with Rankine-cycle engines. In addition, two of the collectors (the Point Focus Central Receiver and the Point Focus Distributed Receiver) were analyzed with Brayton-cycle engines, and the latter of the two also was analyzed with Stirling-cycle engines. This volume describes the systems analyses performed on all the alternative configurations of the seven generic collector concepts and the results obtained. The SOLSTEP computer code used to determine each configuration's system cost and performance is briefly described. The collector and receiver performance calculations used are also presented. The capital investment and related costs that were obtained from the systems studies are presented, and the levelized energy costs are given as a function of capacity factor obtained from the systems studies. Included also are the values of the other attributes used in the concepts' final ranking. The comments, conclusions, and recommendations developed by the PNL study team during the concept characterization and systems analysis tasks of the study are presented. (WHK)

Laity, W.W.; Aase, D.T.; Apley, W.J.; Bird, S.P.; Drost, M.K.; Garrett-Price, B.A.; Williams, T.A.

1980-09-01T23:59:59.000Z

145

Volume Comparison  

Gasoline and Diesel Fuel Update (EIA)

Volume Comparison Volume Comparison Data for October 2013 | Release Date: January 7, 2014 | Complete XLS File Beginning with data for August 2010, natural gas consumption for the residential and commercial sectors was derived from the total system sendout reported by local distribution companies on Form EIA-857, "Monthly Report of Natural Gas Purchases and Deliveries." The new methodology was designed to yield estimates that more closely reflect calendar month consumption patterns. Total system sendout is the sum of all volumes dispatched into the service territory during the report month, less any storage injections and deliveries to points outside the service territory. Previously, residential and commercial consumption estimates were based solely on reported sector

146

Conceptual design and systems analysis of photovoltaic power systems. Final report. Volume III(2). Technology  

DOE Green Energy (OSTI)

Conceptual designs were made and analyses were performed on three types of solar photovoltaic power systems. Included were Residential (1 to 10 kW), Intermediate (0.1 to 10 MW), and Central (50 to 1000 MW) Power Systems to be installed in the 1985 to 2000 time period. The following analyses and simulations are covered: residential power system computer simulations, intermediate power systems computer simulation, central power systems computer simulation, array comparative performance, utility economic and margin analyses, and financial analysis methodology.

Pittman, P.F.

1977-05-01T23:59:59.000Z

147

Conceptual design and systems analysis of photovoltaic power systems. Volume III(1). Technology  

DOE Green Energy (OSTI)

Conceptual designs were made and analyses were performed on three types of solar photovoltaic power systems. Included were Residential (1 to 10 kW), Intermediate (0.1 to 10 MW), and Central (50 to 1000 MW) Power Systems to be installed in the 1985 to 2000 time period. Subsystem technology presented here includes: insolation, concentration, silicon solar cell modules, CdS solar cell module, array structure, battery energy storage, power conditioning, residential power system architectural designs, intermediate power system structural design, and central power system facilities and site survey.

Pittman, P.F.

1977-05-01T23:59:59.000Z

148

Nuclear proliferation and civilian nuclear power: report of the Nonproliferation Alternative Systems Assessment Program. Volume II. Proliferation resistance  

SciTech Connect

Volume II assesses proliferation resistance. Chapters are devoted to: assessment of civilian nuclear systems (once-through fuel-cycle systems, closed fuel cycle systems, research reactors and critical facilities); assessment of associated sensitive materials and facilities (enrichment, problems with storage of spent fuel and plutonium content, and reprocessing and refabrication facilities); and safeguards for alternative fuel cycles.

1979-12-01T23:59:59.000Z

149

Computational Design Studies for an Ion Extraction System for a ''volume-type'' ECR Ion Source  

DOE Green Energy (OSTI)

Numerical studies have been performed for optimally extracting high-intensity, space-charged-limited multi-charged ion beams from an all-permanent-magnet, ''volume-type'' ECR ion source, equipped with a three-electrode extraction system. These studies clearly demonstrate the importance of being able to adjust the extraction gap in order to ensure high quality, minimum divergence (highly transportable) ion beams. Optimum extraction conditions are reached whenever the plasma meniscus has an optimum curvature for a given current density. Optimum perveance (optimum current) values are found to closely agree with those derived from elementary analytical theory for extraction of space-charge-dominated beams. Details of the electrode system design as well as angular divergence and RMS emittance versus extraction parameter data (e.g., perveance and extraction gap) are provided for ion beams of varying charge-state and mass, extracted under the influence of a mirror-geometry plasma confinement magnetic field.

Zaim, H.

2001-11-05T23:59:59.000Z

150

MPI-hybrid Parallelism for Volume Rendering on Large, Multi-core Systems  

Science Conference Proceedings (OSTI)

This work studies the performance and scalability characteristics of"hybrid'" parallel programming and execution as applied to raycasting volume rendering -- a staple visualization algorithm -- on a large, multi-core platform. Historically, the Message Passing Interface (MPI) has become the de-facto standard for parallel programming and execution on modern parallel systems. As the computing industry trends towards multi-core processors, with four- and six-core chips common today and 128-core chips coming soon, we wish to better understand how algorithmic and parallel programming choices impact performance and scalability on large, distributed-memory multi-core systems. Our findings indicate that the hybrid-parallel implementation, at levels of concurrency ranging from 1,728 to 216,000, performs better, uses a smaller absolute memory footprint, and consumes less communication bandwidth than the traditional, MPI-only implementation.

Howison, Mark; Bethel, E. Wes; Childs, Hank

2010-03-20T23:59:59.000Z

151

Hybrid Parallelism for Volume Rendering on Large, Multi-core Systems  

Science Conference Proceedings (OSTI)

This work studies the performance and scalability characteristics of"hybrid'"parallel programming and execution as applied to raycasting volume rendering -- a staple visualization algorithm -- on a large, multi-core platform. Historically, the Message Passing Interface (MPI) has become the de-facto standard for parallel programming and execution on modern parallel systems. As the computing industry trends towards multi-core processors, with four- and six-core chips common today and 128-core chips coming soon, we wish to better understand how algorithmic and parallel programming choices impact performance and scalability on large, distributed-memory multi-core systems. Our findings indicate that the hybrid-parallel implementation, at levels of concurrency ranging from 1,728 to 216,000, performs better, uses a smaller absolute memory footprint, and consumes less communication bandwidth than the traditional, MPI-only implementation.

Howison, Mark; Bethel, E. Wes; Childs, Hank

2010-07-12T23:59:59.000Z

152

Hybrid Parallelism for Volume Rendering on Large, Multi-core Systems  

SciTech Connect

This work studies the performance and scalability characteristics of"hybrid" parallel programming and execution as applied to raycasting volume rendering -- a staple visualization algorithm -- on a large, multi-core platform. Historically, the Message Passing Interface (MPI) has become the de-facto standard for parallel programming and execution on modern parallel systems. As the computing industry trends towards multi-core processors, with four- and six-core chips common today and 128-core chips coming soon, we wish to better understand how algorithmic and parallel programming choices impact performance and scalability on large, distributed-memory multi-core systems. Our findings indicate that the hybrid-parallel implementation, at levels of concurrency ranging from 1,728 to 216,000, performs better, uses a smaller absolute memory footprint, and consumes less communication bandwidth than the traditional, MPI-only implementation.

Howison, Mark; Bethel, E. Wes; Childs, Hank

2010-06-14T23:59:59.000Z

153

Technical and economic assessment of fluidized bed augmented compressed air energy storage system. Volume III. Preconceptual design  

DOE Green Energy (OSTI)

A technical and economic assessment of fluidized bed combustion augmented compressed air energy storage systems is presented. The results of this assessment effort are presented in three volumes. Volume III - Preconceptual Design contains the system analysis which led to the identification of a preferred component configuration for a fluidized bed combustion augmented compressed air energy storage system, the results of the effort which transformed the preferred configuration into preconceptual power plant design, and an introductory evaluation of the performance of the power plant system during part-load operation and while load following.

Giramonti, A.J.; Lessard, R.D.; Merrick, D.; Hobson, M.J.

1981-09-01T23:59:59.000Z

154

Alternate Air Delivery Systems for Hot and Humid Climates  

E-Print Network (OSTI)

Carter & Burgess first began using triple deck multi-zone units, in place of traditional VAV systems, on the Texas State Capitol restoration. Since the completion of that project design in early 1991, our firm has now used triple deck multi-zone units in the Harris County Criminal Courts Building in Houston, one of the most hot and humid climates in the United States, as well as in several other facilities. This paper will discuss the adoption of ASHRAE 62, its effects on VAV systems, and how triple deck multi-zone units offer an alternative system to cooling in hot and humid climates. We recommend all design firms add triple deck multizone units to their repertoire of design solutions.

Wallace, M.

1996-01-01T23:59:59.000Z

155

Two-nucleon systems in a finite volume. II. S13-D13 coupled channels and the deuteron  

Science Conference Proceedings (OSTI)

The energy spectra of two nucleons in a cubic volume provide access to the two phase shifts and one mixing angle that define the S matrix in the S13-D13 coupled channels containing the deuteron. With the aid of recently derived energy quantization conditions for such systems, and the known scattering parameters, these spectra are predicted for a range of volumes. It is found that extractions of the infinite-volume deuteron binding energy and leading scattering parameters, including the S-D mixing angle at the deuteron pole, are possible from lattice QCD calculations of two-nucleon systems with boosts of |P|?2?/L{radical}3 in volumes with 10??fm?L?14??fm. The viability of extracting the asymptotic D/S ratio of the deuteron wave function from lattice QCD calculations is discussed.

Briceno, Raul [JLAB; Davoudi, Zohreh [Washington U.; Luu, Thomas C. [Forschungszentrum Jlich; Savage, Martin J. [Washington U.

2013-12-01T23:59:59.000Z

156

Conversion system overview assessment. Volume II. Solar-wind hybrid systems  

SciTech Connect

Solar-wind hybrid systems are discussed. It is shown that there are large areas in the United States where solar and wind resources are comparable in magnitude and there are diurnal and seasonal complementarities which offer the potential for cost-effective hybrid systems. There are also distinct engineering features of the two conversion technologies. Electric power generation from wind is straightforward and cost-effective, whereas solar thermal conversion to generate heat is more cost-effective than to generate electricity. Examples of hybrid systems utilizing these features in total energy applications are presented.

Jayadev, T. S.; Henderson, J.; Bingham, C.

1979-08-01T23:59:59.000Z

157

Turbine-Generator Auxiliary Systems, Volume 5: Main and Feedpump Turbine Trip Systems  

Science Conference Proceedings (OSTI)

This report describes the trip systems for the mechanical hydraulic control (MHC) and electrohydraulic control (EHC) main turbine and feedpump turbines for the General Electric (GE) and Siemens Westinghouse (SW) units in the United States.

2009-12-23T23:59:59.000Z

158

Multiple-part-type systems in high volume manufacturing : Kanban System design for automatic production scheduling  

E-Print Network (OSTI)

A Kanban Production System is designed to help a factory line meet fluctuating demands for multiple part types. Based on the parameter settings of the Control-Point Policy, the optimum Kanban levels are obtained. The ...

Lee, Kaizhao

2008-01-01T23:59:59.000Z

159

Turbine-Generator Auxiliary Systems, Volume 4: Generator Stator Cooling System  

Science Conference Proceedings (OSTI)

While there is a wealth of specific instructions, guidelines, experiences, and publications associated with water-cooled generators, the industry needs a comprehensive document that provides an unbiased overview of all technologies and related issues. This report deals with the specific features of water-cooled generators and the attached generator cooling water system. Though the primary focus is water-cooled stators, other possible components associated with rotor water cooling or attached systems, suc...

2008-12-22T23:59:59.000Z

160

Handbook for Verification and Validation of Digital Systems, Volume 1: Revision 1 and Volume 2: Case Histories  

Science Conference Proceedings (OSTI)

With the increasing use of digital instrumentation and control systems in power plants, utilities must determine the dependability and predictability of such systems and their software. This updated handbook provides a comprehensive guide to help utilities understand the verification and validation (V&V) process. The handbook presents a graded approach to select convenient V&V methods, develop a V&V plan, generate necessary documentation, and conduct appropriate V&V activities.

1998-12-30T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Blade system design studies volume II : preliminary blade designs and recommended test matrix.  

DOE Green Energy (OSTI)

As part of the U.S. Department of Energy's Wind Partnerships for Advanced Component Technologies (WindPACT) program, Global Energy Concepts, LLC is performing a Blade System Design Study (BSDS) concerning innovations in materials, processes and structural configurations for application to wind turbine blades in the multi-megawatt range. The BSDS Volume I project report addresses issues and constraints identified to scaling conventional blade designs to the megawatt size range, and evaluated candidate materials, manufacturing and design innovations for overcoming and improving large blade economics. The current report (Volume II), presents additional discussion of materials and manufacturing issues for large blades, including a summary of current trends in commercial blade manufacturing. Specifications are then developed to guide the preliminary design of MW-scale blades. Using preliminary design calculations for a 3.0 MW blade, parametric analyses are performed to quantify the potential benefits in stiffness and decreased gravity loading by replacement of a baseline fiberglass spar with carbon-fiberglass hybrid material. Complete preliminary designs are then presented for 3.0 MW and 5.0 MW blades that incorporate fiberglass-to-carbon transitions at mid-span. Based on analysis of these designs, technical issues are identified and discussed. Finally, recommendations are made for composites testing under Part I1 of the BSDS, and the initial planned test matrix for that program is presented.

Griffin, Dayton A. (Global Energy Concepts, LLC, Kirkland, WA)

2004-06-01T23:59:59.000Z

162

Blade system design studies volume II : preliminary blade designs and recommended test matrix.  

SciTech Connect

As part of the U.S. Department of Energy's Wind Partnerships for Advanced Component Technologies (WindPACT) program, Global Energy Concepts, LLC is performing a Blade System Design Study (BSDS) concerning innovations in materials, processes and structural configurations for application to wind turbine blades in the multi-megawatt range. The BSDS Volume I project report addresses issues and constraints identified to scaling conventional blade designs to the megawatt size range, and evaluated candidate materials, manufacturing and design innovations for overcoming and improving large blade economics. The current report (Volume II), presents additional discussion of materials and manufacturing issues for large blades, including a summary of current trends in commercial blade manufacturing. Specifications are then developed to guide the preliminary design of MW-scale blades. Using preliminary design calculations for a 3.0 MW blade, parametric analyses are performed to quantify the potential benefits in stiffness and decreased gravity loading by replacement of a baseline fiberglass spar with carbon-fiberglass hybrid material. Complete preliminary designs are then presented for 3.0 MW and 5.0 MW blades that incorporate fiberglass-to-carbon transitions at mid-span. Based on analysis of these designs, technical issues are identified and discussed. Finally, recommendations are made for composites testing under Part I1 of the BSDS, and the initial planned test matrix for that program is presented.

Griffin, Dayton A. (Global Energy Concepts, LLC, Kirkland, WA)

2004-06-01T23:59:59.000Z

163

Central receiver solar thermal power system. Phase 1. CDRL item 2; Pilot Plant preliminary design report. Volume II. System decription and system analysis  

SciTech Connect

An active system analysis and integration effort has been maintained. These activities have included the transformation of initial program requirements into a preliminary system design, the evolution of subsystem requirements which lay the foundation for subsystem design and test activity, and the overseeing of the final preliminary design effort to ensure that the subsystems are operationally compatible and capable of producing electricity at the lowest possible cost per unit of energy. Volume II of the Preliminary Design Report presents the results of the overall system effort that went on during this contract. The effort is assumed to include not only the total system definition and design but also all subsystem interactions.

Hallet, Jr., R. W.; Gervais, R. L.

1977-10-01T23:59:59.000Z

164

Proceedings of the seventh annual gasification and gas stream cleanup systems contractors review meeting: Volume 2  

Science Conference Proceedings (OSTI)

On June 16 through 19, 1987, METC sponsored the Seventh Annual Gasification and Gas Stream Cleanup Systems Contractors Review Meeting which was held at the Sheraton Lakeview Conference Center in Morgantown, West Virginia. The primary purpose of the meeting was threefold: to review the technical progress and current status of the gasification and gas stream cleanup projects sponsored by the Department of Energy; to foster technology exchange among participating researchers and other technical communities; to facilitate interactive dialogues which would identify research needs that would make coal-based gasification systems more attractive economically and environmentally. More than 310 representatives of Government, academia, industry, and foreign energy research organizations attended the 4-day meeting. Fifty-three papers and thirty poster dsplays were presented summarizing recent developments in the gasification and gas stream cleanup programs. Volume II covers papers presented at sessions 5 and 6 on system for the production of synthesis gas, and on system for the production of power. All papers have been processed for inclusion in the Energy Data Base.

Ghate, M.R.; Markel, K.E. Jr.; Jarr, L.A.; Bossart, S.J. (eds.)

1987-08-01T23:59:59.000Z

165

Assessment of solar options for small power systems applications. Volume III. Analysis of concepts  

SciTech Connect

A comparative analysis of solar thermal conversion concepts that are potentially suitable for development as small electric power systems (1 to 10 MWe) is given. Seven generic types of collectors, together with associated subsystems for electric power generation, were considered. The collectors can be classified into three categories: (1) two-axis tracking (with compound-curvature reflecting surfaces; (2) one-axis tracking (with single-curvature reflecting suraces; and (3) nontracking (with low-concentration reflecting surfaces). All seven collectors were analyzed in conceptual system configurations with Rankine-cycle engines. In addition, two of the collectors (the Point Focus Central Receiver and the Point Focus Distributed Receiver) were analyzed with Brayton-cycle engines, and the latter of the two also was analyzed with Stirling-cycle engines. This volume describes the systems analyses performed on all the alternative configurations of the seven generic collector concepts and the results obtained. The SOLSTEP computer code used to determine each configuration's system cost and performance is briefly described. The collector and receiver performance calculations used are also presented. The capital investment and related costs that were obtained from the systems studies are presented, and the levelized energy costs are given as a function of capacity factor obtained from the systems studies. Included also are the values of the other attributes used in the concepts' final ranking. The comments, conclusions, and recommendations developed by the PNL study team during the concept characterization and systems analysis tasks of the study are presented. (WHK)

Laity, W.W.; Aase, D.T.; Apley, W.J.; Bird, S.P.; Drost, M.K.; Garrett-Price, B.A.; Williams, T.A.

1980-09-01T23:59:59.000Z

166

Proceedings of the seventh annual gasification and gas stream cleanup systems contractors review meeting: Volume 1  

Science Conference Proceedings (OSTI)

On June 16 through 19, 1987, METC sponsored the Seventh Annual Gasification and Gas Stream Cleanup Systems Contractors Review Meeting which was held at the Sheraton Lakeview Conference Center in Morgantown, West Virginia. The primary purpose of the meeting was threefold: to review the technical progress and current status of the gasification and gas stream cleanup projects sponsored by the Department of Energy; to foster technology exchange among participating researchers and other technical communities; to facilitate interactive dialogues which would identify research needs that would make coal-based gasification systems more attractive economically and environmentally. More than 310 representatives of Government, academia, industry, and foreign energy research organizations attended the 4-day meeting. Fifty-three papers and thirty poster displays were presented summarizing recent developments in the gasification and gas stream cleanup programs. Volume I covers information presented at sessions 1 through 4 on systems for the production of Co-products and industrial fuel gas, environmental projects, and components and materials. Individual papers have been processed for the Energy Data Base.

Ghate, M.R.; Markel, K.E. Jr.; Jarr, L.A.; Bossart, S.J. (eds.)

1987-08-01T23:59:59.000Z

167

Assessment of effectiveness of geologic isolation systems. CIRMIS data system. Volume 4. Driller's logs, stratigraphic cross section and utility routines  

SciTech Connect

The Assessment of Effectiveness of Geologic Isolation Systems (AEGIS) Program is developing and applying the methodology for assessing the far-field, long-term post-closure safety of deep geologic nuclear waste repositories. AEGIS is being performed by Pacific Northwest Laboratory (PNL) under contract with the Office of Nuclear Waste Isolation (ONWI) for the Department of Energy (DOE). One task within AEGIS is the development of methodology for analysis of the consequences (water pathway) from loss of repository containment as defined by various release scenarios. Analysis of the long-term, far-field consequences of release scenarios requires the application of numerical codes which simulate the hydrologic systems, model the transport of released radionuclides through the hydrologic systems to the biosphere, and, where applicable, assess the radiological dose to humans. The various input parameters required in the analysis are compiled in data systems. The data are organized and prepared by various input subroutines for use by the hydrologic and transport codes. The hydrologic models simulate the groundwater flow systems and provide water flow directions, rates, and velocities as inputs to the transport models. Outputs from the transport models are basically graphs of radionuclide concentration in the groundwater plotted against time. After dilution in the receiving surface-water body (e.g., lake, river, bay), these data are the input source terms for the dose models, if dose assessments are required. The dose models calculate radiation dose to individuals and populations. CIRMIS (Comprehensive Information Retrieval and Model Input Sequence) Data System is a storage and retrieval system for model input and output data, including graphical interpretation and display. This is the fourth of four volumes of the description of the CIRMIS Data System.

Friedrichs, D.R.

1980-01-01T23:59:59.000Z

168

Solar total energy systems final technical summary report. Volume I. Solar total energy systems market penetration  

SciTech Connect

The results of the market penetration analysis of Solar Total Energy Systems (STES) for the industrial sector are described. Performance data derived for STES commercial applications are included. The energy use and price forecasts used in the analysis are summarized. The STES Applications Model (SAM), has been used to develop data on STES development potential by state and industry as a function of time from 1985 through 2015. A second computer code, the Market Penetration Model (MPM), has been completed and used to develop forecasts of STES market penetration and national energy displacement by fuel type. This model was also used to generate sensitivity factors for incentives, and variations in assumptions of cost of STES competing fuel. Results for the STES performance analysis for commercial applications are presented. (MHR)

Bush, L.R.; Munjal, P.K.

1978-03-31T23:59:59.000Z

169

Decontamination and Volume Reduction System for Transuranic Waste at Los Alamos National Laboratory, Los Alamos, New Mexico Environmental Assessment  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

69 69 Decontamination and Volume Reduction System for Transuranic Waste at Los Alamos National Laboratory, Los Alamos, New Mexico Environmental Assessment Final Document Date Prepared: June 23, 1999 Prepared by: U.S. Department of Energy, Los Alamos Area Office Final document Decontamination and Volume Reduction System EA June 23, 1999 DOE/LAAO iii TABLE OF CONTENTS ACRONYMS AND TERMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v EXECUTIVE SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii 1.0 PURPOSE AND NEED FOR AGENCY ACTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.2 Background . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

170

Performance of thermal distribution systems in large commercial buildings  

NLE Websites -- All DOE Office Websites (Extended Search)

Performance of thermal distribution systems in large commercial buildings Performance of thermal distribution systems in large commercial buildings Title Performance of thermal distribution systems in large commercial buildings Publication Type Journal Article LBNL Report Number LBNL-44331 Year of Publication 2002 Authors Xu, Tengfang T., François Rémi Carrié, Darryl J. Dickerhoff, William J. Fisk, Jennifer A. McWilliams, Duo Wang, and Mark P. Modera Journal Energy and Buildings Volume 34 Start Page Chapter Pagination 215-226 Abstract This paper presents major findings of a field study on the performance of five thermal distribution systems in four large commercial buildings. The five systems studied are typical single-duct or dual-duct constant air volume (CAV) systems and variable air volume (VAV) systems, each of which serves an office building or a retail building with floor area over 2,000 m2. The air leakage from ducts are reported in terms of effective leakage area (ELA) at 25 Pa reference pressure, the ASHRAE-defined duct leakage class, and air leakage ratios. The specific ELAs ranged from 0.7 to 12.9 cm2 per m2 of duct surface area, and from 0.1 to 7.7 cm2 per square meter of floor area served. The leakage classes ranged from 34 to 757 for the five systems and systems sections tested. The air leakage ratios are estimated to be up to one-third of the fan- supplied airflow in the constant-air-volume systems. The specific ELAs and leakage classes indicate that air leakage in large commercial duct systems varies significantly from system to system, and from system section to system section even within the same thermal distribution system. The duct systems measured are much leakier than the ductwork specified as "unsealed ducts" by ASHRAE. Energy losses from supply ducts by conduction (including convection and radiation) are found to be significant, on the scale similar to the losses induced by air leakage in the duct systems. The energy losses induced by leakage and conduction suggest that there are significant energy-savings potentials from duct-sealing and insulation practice in large commercial buildings

171

The Louis Stokes Laboratories, Building 50, National Institutes...  

NLE Websites -- All DOE Office Websites (Extended Search)

VAV supply and exhaust fans, although in the pump system, the VAV terminal units are replaced by water control valves and cooling and heating coils. Differential pressure sensors...

172

Solar assisted heat pump system with volume solar collector. Technical report  

DOE Green Energy (OSTI)

The system uses the attic of the house with a large south facing window as the solar collector. An air-to-water heat pump uses the attic air as a heat source to heat a volume of storage water during the heating season. During the cooling season the attic is ventilated and the heat pump uses the attic air as a heat sink while cooling the storage water. The computer program was developed to include a heat exchanger in the attic which could by-pass the heat pump condenser cooling water, thus permitting direct heat exchange between the attic air and the storage water whenever a favorable temperature existed. The program also accounts for the effect of the incidence angle of insolation and the effect of the number of glass plates on the transmittance and absorptance of the collector and windows. Other refinements include: the use of a sophisticated nighttime setback thermostat, account of internal heat generation and infiltration loss. Among all of the parameter variations, the use of an attic heat exchanger resulted in the maximum savings in the heating/cooling energy consumption of the house. The use of double-glazed windows too, resulted in substantial energy savings. The total energy consumption was found to depend strongly on the infiltration rate. The program was also used to simulate the same system under weather conditions existing at several different geographic areas.

Sabnis, J.S.; Hickox, W.J.; Drucker, E.E.; Ucar, M.; LaGraff, J.E.

1978-09-01T23:59:59.000Z

173

Commercial applications of solar total energy systems. Final report. Volume 2. Technical  

SciTech Connect

The overall objective of this program was to assess the feasibility of using solar energy to provide a significant fraction of the energy needs of commercial buildings that have energy demands greater than 200 kWe. This volume of the final report discusses the approach employed to develop: (1) STES concept configurations and component data, (2) commercial buildings application data, and (3) computer simulation programs for evaluating various STES concept-commercial buildings applications. Various solar thermal and photovoltaic solar total energy systems (STES) configurations were considered. Concurrently, data on commercial buildings (e.g., categories, energy demand, demographic population, etc.) were developed and used to define six model building configurations which could be used as representative commercial buildings within six various regions (12 specific sites) of the United States. The six configurations included four building types (a low rise office building, a large retail store, a medium-size shopping center and a large shopping center) typifying current building designs. The remaining two configurations used the large shopping center model except that the energy demand was changed to reflect future building designs. The STESEP Computer Code was developed for a quick evaluation method for tradeoffs related to (1) cascading of thermal power conversion systems, (2) determination of optimum collector sizes and operating conditions (make or buy decisions for auxiliary energy), and (3) comparison of solar total energy concepts in various parts of the country and in various types of commercial buildings to assess their future economic potential for various economic scenarios. (WHK)

Boobar, M.G.; McFarland, B.L.; Nalbandian, S.J.; Willcox, W.W.; French, E.P.; Smith, K.E.

1978-07-01T23:59:59.000Z

174

Advanced systems demonstration for utilization of biomass as an energy source. Volume III. Equipment specifications  

DOE Green Energy (OSTI)

This volume contains all of the equipment specifications to be utilized for the proposed biomass co-generation plant in Maine. (DMC)

Not Available

1980-10-01T23:59:59.000Z

175

DISTRIBUTED ENERGY SYSTEMS IN CALIFORNIA'S FUTURE: A PRELIMINARY REPORT, VOLUME I  

E-Print Network (OSTI)

~t, Volume 1, 1977. California Energy Resources ConservationAnalysis of the California Energy Industry, p. xvi, Januaryreport to the California Energy Resources Conservation and

Authors, Various

2010-01-01T23:59:59.000Z

176

SCALE: A modular code system for performing standardized computer analyses for licensing evaluation. Miscellaneous -- Volume 3, Revision 4  

Science Conference Proceedings (OSTI)

SCALE--a modular code system for Standardized Computer Analyses Licensing Evaluation--has been developed by Oak Ridge National Laboratory at the request of the US Nuclear Regulatory Commission. The SCALE system utilizes well-established computer codes and methods within standard analysis sequences that (1) allow an input format designed for the occasional user and/or novice; (2) automate the data processing and coupling between modules, and (3) provide accurate and reliable results. System developments has been directed at problem-dependent cross-section processing and analysis of criticality safety, shielding, heat transfer, and depletion/decay problems. Since the initial release of SCALE in 1980, the code system has been heavily used for evaluation of nuclear fuel facility and package designs. This revision documents Version 4.2 of the system. This manual is divided into three volumes: Volume 1--for the control module documentation, Volume 2--for the functional module documentation, and Volume 3--for the data libraries and subroutine libraries.

Petrie, L.M.; Jordon, W.C. [Oak Ridge National Lab., TN (United States); Edwards, A.L. [Oak Ridge National Lab., TN (United States)]|[Lawrence Livermore National Lab., CA (United States)] [and others

1995-04-01T23:59:59.000Z

177

SCALE: A modular code system for performing standardized computer analyses for licensing evaluation. Control modules -- Volume 1, Revision 4  

SciTech Connect

SCALE--a modular code system for Standardized Computer Analyses Licensing Evaluation--has been developed by Oak Ridge National Laboratory at the request of the US Nuclear Regulatory Commission. The SCALE system utilizes well-established computer codes and methods within standard analysis sequences that (1) allow an input format designed for the occasional user and/or novice, (2) automate the data processing and coupling between modules, and (3) provide accurate and reliable results. System development has been directed at problem-dependent cross-section processing and analysis of criticality safety, shielding, heat transfer, and depletion/decay problems. Since the initial release of SCALE in 1980, the code system has been heavily used for evaluation of nuclear fuel facility and package designs. This revision documents Version 4.2 of the system. This manual is divided into three volumes: Volume 1--for the control module documentation, Volume 2--for the functional module documentation, and Volume 3 for the documentation of the data libraries and subroutine libraries.

Landers, N.F.; Petrie, L.M.; Knight, J.R. [Oak Ridge National Lab., TN (United States)] [and others

1995-04-01T23:59:59.000Z

178

Nuclear proliferation and civilian nuclear power. Report of the Nonproliferation Alternative Systems Assessment Program. Volume II. Proliferation resistance  

SciTech Connect

The purpose of this volume is limited to an assessment of the relative effects that particular choices of nuclear-power systems, for whatever reasons, may have on the possible spread of nuclear-weapons capabilities. This volume addresses the concern that non-nuclear-weapons states may be able to initiate efforts to acquire or to improve nuclear-weapons capabilities through civilian nuclear-power programs; it also addresses the concern that subnational groups may obtain and abuse the nuclear materials or facilities of such programs, whether in nuclear-weapons states (NWS's) or nonnuclear-weapons states (NNW's). Accordingly, this volume emphasizes one important factor in such decisions, the resistance of nuclear-power systems to the proliferation of nuclear-weapons capabilities.

1980-06-01T23:59:59.000Z

179

Nuclear proliferation and civilian nuclear power. Report of the Nonproliferation Alternative Systems Assessment Program. Volume II. Proliferation resistance  

SciTech Connect

The purpose of this volume is limited to an assessment of the relative effects that particular choices of nuclear-power systems, for whatever reasons, may have on the possible spread of nuclear-weapons capabilities. This volume addresses the concern that non-nuclear-weapons states may be able to initiate efforts to acquire or to improve nuclear-weapons capabilities through civilian nuclear-power programs; it also addresses the concern that subnational groups may obtain and abuse the nuclear materials or facilities of such programs, whether in nuclear-weapons states (NWS's) or nonnuclear-weapons states (NNW's). Accordingly, this volume emphasizes one important factor in such decisions, the resistance of nuclear-power systems to the proliferation of nuclear-weapons capabilities.

Not Available

1980-06-01T23:59:59.000Z

180

Advanced system demonstration for utilization of biomass as an energy source. Volume V. Electrical and instrumentation elementary diagrams and instrument indexes  

DOE Green Energy (OSTI)

This volume contains detailed drawings and diagrams of electrical systems and instruments which will be included in a biomass cogeneration facility in Maine. (DMC)

None

1980-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Brawley 10 MW Geothermal Plant Plant Manual for Southern Californa Edison Company and Union Oil Company of California. Volume I. Systems Descriptions  

DOE Green Energy (OSTI)

This volume covers Systems Descriptions. It presents each system of the facility and discusses basic features. Brief discussion of each piece of major equipment in system and design conditions.

None

1980-11-28T23:59:59.000Z

182

GENII (Generation II): The Hanford Environmental Radiation Dosimetry Software System: Volume 3, Code maintenance manual: Hanford Environmental Dosimetry Upgrade Project  

Science Conference Proceedings (OSTI)

The Hanford Environmental Dosimetry Upgrade Project was undertaken to incorporate the internal dosimetry models recommended by the International Commission on Radiological Protection (ICRP) in updated versions of the environmental pathway analysis models used at Hanford. The resulting second generation of Hanford environmental dosimetry computer codes is compiled in the Hanford Environmental Dosimetry System (Generation II, or GENII). This coupled system of computer codes is intended for analysis of environmental contamination resulting from acute or chronic releases to, or initial contamination of, air, water, or soil, on through the calculation of radiation doses to individuals or populations. GENII is described in three volumes of documentation. This volume is a Code Maintenance Manual for the serious user, including code logic diagrams, global dictionary, worksheets to assist with hand calculations, and listings of the code and its associated data libraries. The first volume describes the theoretical considerations of the system. The second volume is a Users' Manual, providing code structure, users' instructions, required system configurations, and QA-related topics. 7 figs., 5 tabs.

Napier, B.A.; Peloquin, R.A.; Strenge, D.L.; Ramsdell, J.V.

1988-09-01T23:59:59.000Z

183

GENII: The Hanford Environmental Radiation Dosimetry Software System: Volume 2, Users' manual: Hanford Environmental Dosimetry Upgrade Project  

Science Conference Proceedings (OSTI)

The Hanford Environmental Dosimetry Upgrade Project was undertaken to incorporate the internal dosimetry models recommended by the International Commission on Radiological Protection (ICRP) in updated versions of the environmental pathway analysis models used at Hanford. The resulting second generation of Hanford environmental dosimetry computer codes is compiled in the Hanford Environmental Dosimetry System (Generation II, or GENII). The purpose of this coupled system of computer codes is to analyze environmental contamination of, air, water, or soil. This is accomplished by calculating radiation doses to individuals or populations. GENII is described in three volumes of documentation. This second volume is a Users' Manual, providing code structure, users' instructions, required system configurations, and QA-related topics. The first volume describes the theoretical considerations of the system. The third volume is a Code Maintenance Manual for the user who requires knowledge of code detail. It includes logic diagrams, global dictionary, worksheets, example hand calculations, and listings of the code and its associated data libraries. 27 refs., 17 figs., 23 tabs.

Napier, B.A.; Peloquin, R.A.; Strenge, D.L.; Ramsdell, J.V.

1988-11-01T23:59:59.000Z

184

Energy Research Information System. Volume 1, Number 4. cumulative indexes (project nos. 00000001 through 00000539). Quarterly report  

SciTech Connect

This cumulative index includes a state location index, an organization index and a subject keyword index incorporating the indexes from Energy Research Information System (ERIS), Volume 1, Numbers 1, 2, and 3. This issue, plus the first three ERIS reports, comprise a set of 539 research project references for the states of the Old West Region -- Montana, Nebraska, North Dakota, South Dakota and Wyoming.

Givens, B.M.; Boyd, C.A.

1976-08-01T23:59:59.000Z

185

Nuclear proliferation and civilian nuclear power. Report of the Nonproliferation Alternative Systems Assessment Program. Volume IV. Commercial potential  

Science Conference Proceedings (OSTI)

This volume of the Nonproliferation Alternative Systems Assessment Program (NASAP) report provides time and cost estimates for positioning new nuclear power systems for commercial deployment. The assessment also estimates the rates at which the new systems might penetrate the domestic market, assuming the continuing viability of the massive light-water reactor network that now exists worldwide. This assessment does not recommend specific, detailed program plans and budgets for individual systems; however, it is clear from this analysis that any of the systems investigated could be deployed if dictated by national interest.

Not Available

1980-06-01T23:59:59.000Z

186

Finite Volume Based Computer Program for Ground Source Heat Pump System  

SciTech Connect

This report is a compilation of the work that has been done on the grant DE-EE0002805 entitled ?Finite Volume Based Computer Program for Ground Source Heat Pump Systems.? The goal of this project was to develop a detailed computer simulation tool for GSHP (ground source heat pump) heating and cooling systems. Two such tools were developed as part of this DOE (Department of Energy) grant; the first is a two-dimensional computer program called GEO2D and the second is a three-dimensional computer program called GEO3D. Both of these simulation tools provide an extensive array of results to the user. A unique aspect of both these simulation tools is the complete temperature profile information calculated and presented. Complete temperature profiles throughout the ground, casing, tube wall, and fluid are provided as a function of time. The fluid temperatures from and to the heat pump, as a function of time, are also provided. In addition to temperature information, detailed heat rate information at several locations as a function of time is determined. Heat rates between the heat pump and the building indoor environment, between the working fluid and the heat pump, and between the working fluid and the ground are computed. The heat rates between the ground and the working fluid are calculated as a function time and position along the ground loop. The heating and cooling loads of the building being fitted with a GSHP are determined with the computer program developed by DOE called ENERGYPLUS. Lastly COP (coefficient of performance) results as a function of time are provided. Both the two-dimensional and three-dimensional computer programs developed as part of this work are based upon a detailed finite volume solution of the energy equation for the ground and ground loop. Real heat pump characteristics are entered into the program and used to model the heat pump performance. Thus these computer tools simulate the coupled performance of the ground loop and the heat pump. The price paid for the three-dimensional detail is the large computational times required with GEO3D. The computational times required for GEO2D are reasonable, a few minutes for a 20 year simulation. For a similar simulation, GEO3D takes days of computational time. Because of the small simulation times with GEO2D, a number of attractive features have been added to it. GEO2D has a user friendly interface where inputs and outputs are all handled with GUI (graphical user interface) screens. These GUI screens make the program exceptionally easy to use. To make the program even easier to use a number of standard input options for the most common GSHP situations are provided to the user. For the expert user, the option still exists to enter their own detailed information. To further help designers and GSHP customers make decisions about a GSHP heating and cooling system, cost estimates are made by the program. These cost estimates include a payback period graph to show the user where their GSHP system pays for itself. These GSHP simulation tools should be a benefit to the advancement of GSHP systems.

Menart, James A. [Wright State University] [Wright State University

2013-02-22T23:59:59.000Z

187

Recovery Act: Finite Volume Based Computer Program for Ground Source Heat Pump Systems  

SciTech Connect

This report is a compilation of the work that has been done on the grant DE-EE0002805 entitled ???¢????????Finite Volume Based Computer Program for Ground Source Heat Pump Systems.???¢??????? The goal of this project was to develop a detailed computer simulation tool for GSHP (ground source heat pump) heating and cooling systems. Two such tools were developed as part of this DOE (Department of Energy) grant; the first is a two-dimensional computer program called GEO2D and the second is a three-dimensional computer program called GEO3D. Both of these simulation tools provide an extensive array of results to the user. A unique aspect of both these simulation tools is the complete temperature profile information calculated and presented. Complete temperature profiles throughout the ground, casing, tube wall, and fluid are provided as a function of time. The fluid temperatures from and to the heat pump, as a function of time, are also provided. In addition to temperature information, detailed heat rate information at several locations as a function of time is determined. Heat rates between the heat pump and the building indoor environment, between the working fluid and the heat pump, and between the working fluid and the ground are computed. The heat rates between the ground and the working fluid are calculated as a function time and position along the ground loop. The heating and cooling loads of the building being fitted with a GSHP are determined with the computer program developed by DOE called ENERGYPLUS. Lastly COP (coefficient of performance) results as a function of time are provided. Both the two-dimensional and three-dimensional computer programs developed as part of this work are based upon a detailed finite volume solution of the energy equation for the ground and ground loop. Real heat pump characteristics are entered into the program and used to model the heat pump performance. Thus these computer tools simulate the coupled performance of the ground loop and the heat pump. The price paid for the three-dimensional detail is the large computational times required with GEO3D. The computational times required for GEO2D are reasonable, a few minutes for a 20 year simulation. For a similar simulation, GEO3D takes days of computational time. Because of the small simulation times with GEO2D, a number of attractive features have been added to it. GEO2D has a user friendly interface where inputs and outputs are all handled with GUI (graphical user interface) screens. These GUI screens make the program exceptionally easy to use. To make the program even easier to use a number of standard input options for the most common GSHP situations are provided to the user. For the expert user, the option still exists to enter their own detailed information. To further help designers and GSHP customers make decisions about a GSHP heating and cooling system, cost estimates are made by the program. These cost estimates include a payback period graph to show the user where their GSHP system pays for itself. These GSHP simulation tools should be a benefit to the advancement of GSHP system

James A Menart, Professor

2013-02-22T23:59:59.000Z

188

Commercial applications of solar total energy systems. Volume 4. Appendices. Final report. [Solar Total Energy System Evaluation Program (STESEP) code  

DOE Green Energy (OSTI)

A methodology has been developed by Atomics International under contract to the Department of Energy to define the applicability of solar total energy systems (STES) to the commercial sector (e.g., retail stores, shopping centers, offices, etc.) in the United States. Candidate STES concepts were selected to provide on-site power generation capability, as well as thermal energy for both heating and cooling applications. Each concept was evaluated on the basis of its cost effectiveness (i.e., as compared to other concepts) and its ability to ultimately penetrate and capture a significant segment of this market, thereby resulting in a saving of fossil fuel resources. This volume contains the appendices. Topics include deterministic insolation model computer code; building energy usage data; computer simulation programs for building energy demand analysis; model buildings for STES evaluation; Solar Total Energy System Evaluation Program (STESEP) computer code; transient simulation of STES concept; solar data tape analysis; program listings and sample output for use with TRNSYS; transient simulation, and financial parameters sensitivities. (WHK)

Boobar, M.G.; McFarland, B.L.; Nalbandian, S.J.; Willcox, W.W.; French, E.P.; Smith, K.E.

1978-07-01T23:59:59.000Z

189

Model documentation of the Short-Term Coal Analysis System. Volume 2. Model description. [SCOAL  

Science Conference Proceedings (OSTI)

This is the second of three volumes of documentation for the Short-Term Coal Analysis System (SCOAL) developed by the Coal Data Analysis and Forecasting Branch, Office of Coal, Nuclear, Electric, and Alternate Fuels. The principal aim of SCOAL is to project on a quarterly basis the likely contribution of each of the 26 major bituminous coal, lignite, and anthracite producing states to total US production. A secondary objective is to estimate a companion demand-side aggregated by region but disaggregated by end-use sector. In its current use, the two sides are operated in tandem, and serve to cross-validate each other by means of tracking market balances. The purposes of this report are to describe the estimation method, results, and performance evaluation criteria that were deemed relevant in assessing the potential predictive performance of SCOAL's statistically fitted relationships and to discuss the pre- and post-estimation considerations that prevailed over the course of mode development. The single equation parameter estimates, associated significance levels, statistical equation performance measures, and general comments regarding SCOAL's supply and demand side equations are presented.

Not Available

1983-04-01T23:59:59.000Z

190

Southern cone energy network coal gasification for SNG production and pipeline system feasibility study (Brazil). Volume 2. Export trade information  

Science Conference Proceedings (OSTI)

Part I of the volume reports on the coal gasification plant study performed by the Advanced Technology Division of Fluor Engineers and Constructors, Inc., together with information on coal resources and markets, gas demand, and by-product markets provided by Jaakko Poyry. Jaakko Poyry also supported the study with site, cost, economic, and other required local Brazilian data. Part II of the volume presents the results of Fluor's study of an SNG gas transport and gas distribution system. Also included are the results of an alternate study into barging coal north to a gasification plant located in the Santos area.

Not Available

1992-08-01T23:59:59.000Z

191

Assessment of Energy Storage Alternatives in the Puget Sound Energy System Volume 2: Energy Storage Evaluation Tool  

DOE Green Energy (OSTI)

This volume presents the battery storage evaluation tool developed at Pacific Northwest National Laboratory (PNNL), which is used to evaluate benefits of battery storage for multiple grid applications, including energy arbitrage, balancing service, capacity value, distribution system equipment deferral, and outage mitigation. This tool is based on the optimal control strategies to capture multiple services from a single energy storage device. In this control strategy, at each hour, a look-ahead optimization is first formulated and solved to determine battery base operating point. The minute by minute simulation is then performed to simulate the actual battery operation. This volume provide background and manual for this evaluation tool.

Wu, Di; Jin, Chunlian; Balducci, Patrick J.; Kintner-Meyer, Michael CW

2013-12-01T23:59:59.000Z

192

Water Reactor Chemical Volume and Control System and Steam Generator Blowdown Resins and Filters Sourcebook: 2013 Edition  

Science Conference Proceedings (OSTI)

An understanding of ion exchange practices within the industry for the removal of soluble and insoluble contaminants and filtration practices for the removal of insoluble contaminants is important for providing insight into beneficial practices as well as conditions to avoid. This report includes information on system descriptions, system operating practices, resins, and filters used in pressurized water reactor (PWR) chemical volume and control, makeup purification, and steam generator blowdown ...

2013-08-23T23:59:59.000Z

193

SOLERAS - Solar Energy Water Desalination Project: Catalytic. System design final report. Volume 1. System requirement definition and system analysis  

Science Conference Proceedings (OSTI)

Catalytic Inc. was awarded a contract to conduct a preliminary system design and cost analysis for a brackish water desalination project to be located in Brownsville, Texas. System analyses and economic analyses were performed to define the baseline solar energy desalination system. The baseline system provides an average daily product water capacity of 6000 mT. The baseline system is optimal relative to technological risk, performance, and product water cost. Subsystems and their interfaces have been defined and product water cost projections made for commercial plants in a range of capacities. Science Applications, Inc. (SAI), subcontractor to Catalytic, had responsibility for the solar power system. This, the final report, summarizes the work performed under the Phase I effort.

Not Available

1986-01-01T23:59:59.000Z

194

How the Number and Placement of Sensors Controlling Room Air Distribution Systems Affect Energy Use and Comfort  

E-Print Network (OSTI)

This study assesses the impact of sensor number and placement on the energy needed to condition a typical office using several likely variants of an underfloor air distribution system (UFAD). The study uses an empirical-based room stratification model developed from full-scale tests of UFAD systems. Annual energy consumption is calculated for an interior zone using outside air temperature bin data. The comfort criteria are taken from ASHRAE standard 55-92. The simulations indicate that there are benefits derived from using more than one temperature sensor to control conditions in the occupied zone of a room. Among these are: 1. By adjusting both supply air temperature and volume to maintain the maximum allowable thermal gradient in the occupied (lower) part of the room, an optimal supply air condition can reduce energy use (relative to the best arrangement of a single sensor) while maintaining comfort; 2. Discomfort caused by stratification can be detected by having one of the sensors located at foot level; 3. For the simulated UFAD interior zone of a typical office building in Sacramento, an overall energy saving of 8%/24% (VAV/CAV respectively) can be achieved when two sensors as opposed to one are used to control room conditions.

Wang, D.; Arens, E.; Webster, T.; Shi, M.

2002-01-01T23:59:59.000Z

195

Systems Description; Sperry Low Temperature Geothermal Conversion System - Phase I and Phase II; Final Report, Volume III  

DOE Green Energy (OSTI)

This Volume should be considered the introductory volume to the series of six volumes even though numbered out of sequence. Volumes I and II were completed first and released in 1981 while a staff member was available to do the work. Volumes III through VI are being written and released some two years later as DOE funding became available for the purpose. They are as complete as possible considering that almost all the people involved in the program are now unavailable. This Volume III is an overview of the entire program, and many of the items presented herein briefly will be found in expanded form in one of the other five volumes. It will be noticed that assumptions and parameters such as well flow, well temperature, wet bulb temperatures, etc., involved in the several different performance calculations in the volume vary somewhat. These calculations were made at different times for different purposes and no attempt has been made to bring them into exact agreement.

Matthews, Hugh B.

1982-01-01T23:59:59.000Z

196

A flexible assembly system for low volume and high diversity production  

E-Print Network (OSTI)

This thesis project seeks to optimize floor layouts for semiconductor equipment assembly operations. The assembly of semiconductor equipment is characterized by low volume and high product diversity and complexity. Demand ...

Schwenke, Richard Clemens

2009-01-01T23:59:59.000Z

197

FY 93 thermal loading systems study final report: Volume 2. Revision 1  

Science Conference Proceedings (OSTI)

The ability to meet the overall performance requirements for the proposed Mined Geology Disposal System at Yucca Mountain, Nevada requires the two major subsystem (natural barriers and engineered barriers) to positively contribute to containment and radionuclide isolation. In addition to the postclosure performance the proposed repository must meet preclosure requirements of safety, retrievability, and operability. Cost and schedule were also considered. The thermal loading strategy chosen may significantly affect both the postclosure and preclosure performance of the proposed repository. Although the current Site Characterization Plan reference case is 57 kilowatts (kW)/acre, other thermal loading strategies (different areal mass loadings) have been proposed which possess both advantages and disadvantages. The objectives of the FY 1993 Thermal Loading Study were to (1) place bounds on the thermal loading which would establish the loading regime that is ``too hot`` and the loading regime that is ``too cold``, to (2) ``grade`` or evaluate the performance, as a function of thermal loading, of the repository to contain high level wastes against performance criteria and to (3) evaluate the performance of the various options with respect to cost, safety, and operability. Additionally, the effort was to (4) identify important uncertainties that need to be resolved by tests and/or analyses in order to complete a performance assessment on the effects of thermal loading. The FY 1993 Thermal Loading Study was conducted from December 1, 1992 to December 30, 1993 and this final report provides the findings of the study. Volume 2 consists of 10 appendices which contain the following: Waste Stream Analysis; Waste Package Design Inputs; Subsurface Design Inputs; Thermal-Hydrologic Model Inputs; Near-Field Calculations; Far-Field; Reliability of Electronics as a Function of Temperature; Cost Analysis Details; Geochemistry; and Areas of Uncertainty in Thermal Loading.

NONE

1994-08-29T23:59:59.000Z

198

Fort Calhoun Instrumentation & Control Systems Assessment: Volume 1: Baseline Evaluation of I&C Systems; Volume 2: Upgrade Evaluatio n for Electro Hydraulic Control and Turbine Supervisor  

Science Conference Proceedings (OSTI)

EPRI and Omaha Public Power District (OPPD), as a member utility, initiated the long term strategic planning process for the Calhoun instrumentation and control (I&C) systems. The first step was to perform a baseline evaluation of selected I&C systems, generating system status summaries to highlight both problems and opportunities for improvement. Then a more detailed upgrade evaluation was performed to investigate the potential benefits of upgrading the electro hydraulic control and turbine supervisory ...

1998-08-31T23:59:59.000Z

199

K East basin sludge volume estimates for integrated water treatment system  

Science Conference Proceedings (OSTI)

This document provides estimates of the volume of sludge expected from Integrated Process Strategy (IPS) processing of the fuel elements and in the fuel storage canisters in K East Basin. The original estimates were based on visual observations of fuel element condition in the basin and laboratory measurements of canister sludge density. Revision 1 revised the volume estimates of sludge from processing of the fuel elements based on additional data from evaluations of material from the KE Basin fuel subsurface examinations. A nominal Working Estimate and an upper level Working Bound is developed for the canister sludge and the fuel wash sludge components in the KE Basin.

Pearce, K.L.

1998-08-19T23:59:59.000Z

200

Advanced system demonstration for utilization of biomass as an energy source. Volume IV. Design drawings  

DOE Green Energy (OSTI)

This volume contains design drawings for the biomass cogeneration plant to be built in Maine. The drawings show a considerable degree of detail, however, they are not to be considered released for construction. There has been no actual procurement of equipment, therefore equipment drawings certified by suppliers have not been included. (DMC)

None

1980-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Distributed Energy Systems in California's Future: A Preliminary Report Volume 2  

E-Print Network (OSTI)

surrounding a wind energy conversion system may be the bestEnergy System Grouping of Technical Options for Formulation of Distributed Energy Systems Biomass Conversion .

Balderston, F.

2010-01-01T23:59:59.000Z

202

Applied research on energy storage and conversion for photovoltaic and wind energy systems. Volume II. Photovoltaic systems with energy storage. Final report  

DOE Green Energy (OSTI)

This volume of the General Electric study was directed at an evaluation of those energy storage technologies deemed best suited for use in conjunction with a photovoltaic energy conversion system in utility, residential and intermediate applications. Break-even cost goals are developed for several storage technologies in each application. These break-even costs are then compared with cost projections presented in Volume I of this report to show technologies and time frames of potential economic viability. The form of the presentation allows the reader to use more accurate storage system cost data as they become available. The report summarizes the investigations performed and presents the results, conclusions and recommendations pertaining to use of energy storage with photovoltaic energy conversion systems. Candidate storage concepts studied include (1) above ground and underground pumped hydro, (2) underground compressed air, (3) electric batteries, (4) flywheels, and (5) hydrogen production and storage. (WHK)

Not Available

1978-01-01T23:59:59.000Z

203

Economic evaluation of the annual cycle energy system (ACES). Final report. Volume III, appendices  

SciTech Connect

This volume consists of seven appendices related to ACES, the first three of which are concerned with computer programs. The appendices are entitled: (A) ACESIM: Residential Program Listing; (B) Typical Inputs and Outputs of ACESIM; (C) CACESS: Commercial Building Program Listing; (D) Typical Weather-Year Selection Requirements; (E) Building Characteristics; (F) List of Major Variables Used in the Computer Programs; and (G) Bibliography. 79 references.

Not Available

1980-06-01T23:59:59.000Z

204

Design, cost, and performance comparisons of several solar thermal systems for process heat. Volume III. Receivers  

DOE Green Energy (OSTI)

The receiver subsystem converts reflected solar radiation into thermal power by heating a working fluid. The objective of the task described was to estimate the cost and performance of the receiver subsystem for parabolic troughs, parabolic dishes, and central receivers over a wide range of temperatures and power levels for thermal power applications. This volume presents the fundamental design philosophy employed, the constraints identified, the tradeoffs performed and the cost and performance results obtained for each receiver in the study matrix.

Woodard, J.B. Jr.

1981-03-01T23:59:59.000Z

205

IEA Wind Task 24 Integration of Wind and Hydropower Systems; Volume 2: Participant Case Studies  

SciTech Connect

This report describes the background, concepts, issues and conclusions related to the feasibility of integrating wind and hydropower, as investigated by the members of IEA Wind Task 24. It is the result of a four-year effort involving seven IEA member countries and thirteen participating organizations. The companion report, Volume 2, describes in detail the study methodologies and participant case studies, and exists as a reference for this report.

Acker, T.

2011-12-01T23:59:59.000Z

206

Application analysis of solar total energy systems to the residential sector. Volume III, conceptual design. Final report  

DOE Green Energy (OSTI)

The objective of the work described in this volume was to conceptualize suitable designs for solar total energy systems for the following residential market segments: single-family detached homes, single-family attached units (townhouses), low-rise apartments, and high-rise apartments. Conceptual designs for the total energy systems are based on parabolic trough collectors in conjunction with a 100 kWe organic Rankine cycle heat engine or a flat-plate, water-cooled photovoltaic array. The ORC-based systems are designed to operate as either independent (stand alone) systems that burn fossil fuel for backup electricity or as systems that purchase electricity from a utility grid for electrical backup. The ORC designs are classified as (1) a high temperature system designed to operate at 600/sup 0/F and (2) a low temperature system designed to operate at 300/sup 0/F. The 600/sup 0/F ORC system that purchases grid electricity as backup utilizes the thermal tracking principle and the 300/sup 0/F ORC system tracks the combined thermal and electrical loads. Reject heat from the condenser supplies thermal energy for heating and cooling. All of the ORC systems utilize fossil fuel boilers to supply backup thermal energy to both the primary (electrical generating) cycle and the secondary (thermal) cycle. Space heating is supplied by a central hot water (hydronic) system and a central absorption chiller supplies the space cooling loads. A central hot water system supplies domestic hot water. The photovoltaic system uses a central electrical vapor compression air conditioning system for space cooling, with space heating and domestic hot water provided by reject heat from the water-cooled array. All of the systems incorporate low temperature thermal storage (based on water as the storage medium) and lead--acid battery storage for electricity; in addition, the 600/sup 0/F ORC system uses a therminol-rock high temperature storage for the primary cycle. (WHK)

Not Available

1979-07-01T23:59:59.000Z

207

Detailed Field Evaluation of a Cold Air Distribution System: Volumes 1 and 2  

Science Conference Proceedings (OSTI)

When following report recommendations, the system investigated in this study would provide significant energy consumption savings over conventional 55 degrees F supply air systems. Reduced duct size requirements, moreover, promise greater system design flexibility without sacrificing space comfort conditions or indoor air quality. Demonstrating the viability of cold air distribution systems, the report includes suggestions for improving system performance and overall efficiency.

1990-02-01T23:59:59.000Z

208

DISTRIBUTED ENERGY SYSTEMS IN CALIFORNIA'S FUTURE: A PRELIMINARY REPORT, VOLUME I  

E-Print Network (OSTI)

of conventional energy conversion systems. The approachlarge-scale wave energy conversion systems have been built.energy is determined by the end-use amenity provided, conversion efficiency and the supply system

Authors, Various

2010-01-01T23:59:59.000Z

209

Distributed Energy Systems in California's Future: A Preliminary Report Volume 2  

E-Print Network (OSTI)

area at 12% efficiency, comparable to solar thermal electricsolar-electric system can achieve the thermalsolar heat is o These solar thermal systems

Balderston, F.

2010-01-01T23:59:59.000Z

210

DISTRIBUTED ENERGY SYSTEMS IN CALIFORNIA'S FUTURE: A PRELIMINARY REPORT, VOLUME I  

E-Print Network (OSTI)

DOCU[viENTS SECTION DISTRIBUTED ENERGY SYSTEMS STUDY GROUPIMPLICATIONS OF UTILIZING DISTRIBUTED ENERGY TECHNOLOGIES .the development of distributed energy systems. technologies.

Authors, Various

2010-01-01T23:59:59.000Z

211

Transportation Sector Model of the National Energy Modeling System. Volume 2 -- Appendices: Part 3  

SciTech Connect

This Appendix consists of two unpublished reports produced by Energy and Environmental Analysis, Inc., under contract to Oak Ridge National Laboratory. These two reports formed the basis for the subsequent development of the Fuel Economy Model described in Volume 1. They are included in order to document more completely the efforts undertaken to construct a comprehensive model of automobile fuel economy. The supplemental reports are as follows: Supplement 1--Documentation Attributes of Technologies to Improve Automotive Fuel Economy; Supplement 2--Analysis of the Fuel Economy Boundary for 2010 and Comparison to Prototypes.

NONE

1998-01-01T23:59:59.000Z

212

Feasibility of developing a portable driver performance data acquisition system for human factors research: Technical tasks. Volume 1  

SciTech Connect

A two-phase, multi-year research program entitled ``development of a portable driver performance data acquisition system for human factors research`` was recently completed. The primary objective of the project was to develop a portable data acquisition system for crash avoidance research (DASCAR) that will allow drive performance data to be collected using a large variety of vehicle types and that would be capable of being installed on a given vehicle type within a relatively short-time frame. During phase 1 a feasibility study for designing and fabricating DASCAR was conducted. In phase 2 of the research DASCAR was actually developed and validated. This technical memorandum documents the results from the feasibility study. It is subdivided into three volumes. Volume one (this report) addresses the last five items in the phase 1 research and the first issue in the second phase of the project. Volumes two and three present the related appendices, and the design specifications developed for DASCAR respectively. The six tasks were oriented toward: identifying parameters and measures; identifying analysis tools and methods; identifying measurement techniques and state-of-the-art hardware and software; developing design requirements and specifications; determining the cost of one or more copies of the proposed data acquisition system; and designing a development plan and constructing DASCAR. This report also covers: the background to the program; the requirements for the project; micro camera testing; heat load calculations for the DASCAR instrumentation package in automobile trunks; phase 2 of the research; the DASCAR hardware and software delivered to the National Highway Traffic Safety Administration; and crash avoidance problems that can be addressed by DASCAR.

Carter, R.J.; Barickman, F.S.; Spelt, P.F.; Schmoyer, R.L.; Kirkpatrick, J.R.

1998-01-01T23:59:59.000Z

213

Survey of strong motion earthquake effects on thermal power plants in California with emphasis on piping systems. Volume 2, Appendices  

Science Conference Proceedings (OSTI)

Volume 2 of the ``Survey of Strong Motion Earthquake Effects on Thermal Power Plants in California with Emphasis on Piping Systems`` contains Appendices which detail the detail design and seismic response of several power plants subjected to strong motion earthquakes. The particular plants considered include the Ormond Beach, Long Beach and Seal Beach, Burbank, El Centro, Glendale, Humboldt Bay, Kem Valley, Pasadena and Valley power plants. Included is a typical power plant piping specification and photographs of typical power plant piping specification and photographs of typical piping and support installations for the plants surveyed. Detailed piping support spacing data are also included.

Stevenson, J.D. [Stevenson and Associates, Cleveland, OH (United States)

1995-11-01T23:59:59.000Z

214

Application analysis of solar total energy systems to the residential sector. Volume II, energy requirements. Final report  

DOE Green Energy (OSTI)

This project analyzed the application of solar total energy systems to appropriate segments of the residential sector and determined their market penetration potential. This volume covers the work done on energy requirements definition and includes the following: (1) identification of the single-family and multi-family market segments; (2) regionalization of the United States; (3) electrical and thermal load requirements, including time-dependent profiles; (4) effect of conservation measures on energy requirements; and (5) verification of simulated load data with real data.

Not Available

1979-07-01T23:59:59.000Z

215

Nuclear proliferation and civilian nuclear power. Report of the Nonproliferation Alternative Systems Assessment Program. Volume VII. International perspectives  

SciTech Connect

The purpose of this volume is to assess the proliferation vulnerabilities of the present deployment of civilian nuclear-power systems within the current nonproliferation regime and, in light of their prospective deployment, to consider technical and institutional measures and alternatives which may contribute to an improved regime in which nuclear power could play a significant part. An assessment of these measures must include consideration of their nonproliferation effectiveness as well as their bearing upon energy security, and their operational, economic, and political implications. The nature of these considerations can provide some measure of their likely acceptability to various nations.

Not Available

1980-06-01T23:59:59.000Z

216

Distributed Energy Systems in California's Future: A Preliminary Report Volume 2  

E-Print Network (OSTI)

Space Conditioning Systems in Northern California: A Brief Survey, LBL-5229, August 1976. Jet Propulsion

Balderston, F.

2010-01-01T23:59:59.000Z

217

Distributed Energy Systems in California's Future: A Preliminary Report Volume 2  

E-Print Network (OSTI)

wind energy conversibn systems. If located in coastal areas, the California Coastal Commission policies

Balderston, F.

2010-01-01T23:59:59.000Z

218

Distributed Energy Systems in California's Future: A Preliminary Report Volume 2  

E-Print Network (OSTI)

OF UTILIZING DISTRIBUTED ENERGY TECHNOLOGIES . . . . . . .DISTRIBUTED ENERGY SYSTEMS I~N CALIF RNIA/S FUTURE: UU-6831Ur'l1E:i\\i-fS SECTION DISTRIBUTED ENERGY SYSTEMS STUDY GROUP

Balderston, F.

2010-01-01T23:59:59.000Z

219

User Instructions for the Systems Assessment Capability, Rev. 1, Computer Codes Volume 3: Utility Codes  

SciTech Connect

This document contains detailed user instructions for a suite of utility codes developed for Rev. 1 of the Systems Assessment Capability. The suite of computer codes for Rev. 1 of Systems Assessment Capability performs many functions.

Eslinger, Paul W.; Aaberg, Rosanne L.; Lopresti, Charles A.; Miley, Terri B.; Nichols, William E.; Strenge, Dennis L.

2004-09-14T23:59:59.000Z

220

A High-Volume Cryosampler and Sample Purification System for Bromine Isotope Studies of Methyl Bromide  

Science Conference Proceedings (OSTI)

A system was developed for collecting from the ambient atmosphere the methyl halides CH3Cl and CH3Br in quantities sufficient for chlorine and bromine isotope analysis. The construction and operation of the novel cryogenic collection system (...

Brett F. Thornton; Axel Horst; Daniel Carrizo; Henry Holmstrand; Per Andersson; Patrick M. Crill; rjan Gustafsson

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

A High-Volume Cryosampler and Sample Purification System for Bromine Isotope Studies of Methyl Bromide  

Science Conference Proceedings (OSTI)

A system was developed for collecting from the ambient atmosphere the methyl halides CH3Cl and CH3Br in quantities sufficient for chlorine and bromine isotope analysis. The construction and operation of the novel cryogenic collection system (...

Brett F. Thornton; Axel Horst; Daniel Carrizo; Henry Holmstrand; Per Andersson; Patrick M. Crill; rjan Gustafsson

2013-09-01T23:59:59.000Z

222

Hybrid Parallelism for Volume Rendering on Large, Multi- and Many-core Systems  

SciTech Connect

With the computing industry trending towards multi- and many-core processors, we study how a standard visualization algorithm, ray-casting volume rendering, can benefit from a hybrid parallelism approach. Hybrid parallelism provides the best of both worlds: using distributed-memory parallelism across a large numbers of nodes increases available FLOPs and memory, while exploiting shared-memory parallelism among the cores within each node ensures that each node performs its portion of the larger calculation as efficiently as possible. We demonstrate results from weak and strong scaling studies, at levels of concurrency ranging up to 216,000, and with datasets as large as 12.2 trillion cells. The greatest benefit from hybrid parallelism lies in the communication portion of the algorithm, the dominant cost at higher levels of concurrency. We show that reducing the number of participants with a hybrid approach significantly improves performance.

Howison, Mark; Bethel, E. Wes; Childs, Hank

2011-01-01T23:59:59.000Z

223

ETX-I: First-generation single-shaft electric propulsion system program: Volume 2, Battery final report  

Science Conference Proceedings (OSTI)

The overall objective of this research and development program was to advance ac powertrain technology for electric vehicles (EV). The program focused on the design, build, test, and refinement of an experimental advanced electric vehicle powertrain suitable for packaging in a Ford Escort or equivalent-size vehicle. A Mercury LN7 was subsequently selected for the test bed vehicle. Although not part of the initial contract, the scope of the ETX-I Program was expanded in 1983 to encompass the development of advanced electric vehicle batteries compatible with the ETX-I powertrain and vehicle test bed. The intent of the battery portion of the ETX-I Program was to apply the best available battery technology based on existing battery developments. The battery effort was expected to result in a practical scale-up of base battery technologies to the vehicle battery subsystem level. With the addition of the battery activity, the ETX-I Program became a complete proof-of-concept ''ac propulsion system'' technology development program. In this context, the term ''propulsion system'' is defined as all components and subsystems (from the driver input to the vehicle wheels) that are required to store energy on board the vehicle and, using that energy, to provide controlled motive power to the vehicle. This report, Volume II, describes the battery portion of the ETX-I Program. The powertrain effort is reported in Volume I.

Not Available

1988-06-01T23:59:59.000Z

224

SOLERAS - Solar Controlled Environment Agriculture Project. Final report, Volume 2. Battelle Columbus Laboratories system requirements definition and system analysis  

Science Conference Proceedings (OSTI)

System specifications, design criteria, and representative weather data necessary for the system evolution and preliminary design are generated. A detailed analysis and evaluation of the commercial-sized controlled environment agriculture system coupled with a solar energy system was conducted. A simulation model to test the performance of the greenhouse is presented. (BCS)

Not Available

1981-01-01T23:59:59.000Z

225

High-Performance Home Technologies: Solar Thermal & Photovoltaic Systems; Volume 6 Building America Best Practices Series  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

by by Pacific Northwest National Laboratory & Oak Ridge National Laboratory June 4, 2007 June 2007 * NREL/TP-550-41085 PNNL-16362 High-Performance Home Technologies: Solar Thermal & Photovoltaic Systems Building America Best Practices Series Volume 6 High-Performance Home Technologies: Solar Thermal & Photovoltaic Systems Building America Best Practices Series Prepared by Pacific Northwest National Laboratory, a DOE national laboratory Michael C. Baechler Theresa Gilbride, Kathi Ruiz, Heidi Steward and Oak Ridge National Laboratory, a DOE national laboratory Pat M. Love June 4, 2007 DISCLAIMER This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor Battelle Memorial Institute, nor any of their employees, makes any warranty,

226

Fort Hood Solar Total Energy Project. Volume II. Preliminary design. Part 1. System criteria and design description. Final report  

DOE Green Energy (OSTI)

This volume documents the preliminary design developed for the Solar Total Energy System to be installed at Fort Hood, Texas. Current system, subsystem, and component designs are described and additional studies which support selection among significant design alternatives are presented. Overall system requirements which form the system design basis are presented. These include program objectives; performance and output load requirements; industrial, statutory, and regulatory standards; and site interface requirements. Material in this section will continue to be issued separately in the Systems Requirements Document and maintained current through revision throughout future phases of the project. Overall system design and detailed subsystem design descriptions are provided. Consideration of operation and maintenance is reflected in discussion of each subsystem design as well as in an integrated overall discussion. Included are the solar collector subsystem; the thermal storage subsystem, the power conversion sybsystem (including electrical generation and distribution); the heating/cooling and domestic hot water subsystems; overall instrumentation and control; and the STES building and physical plant. The design of several subsystems has progressed beyond the preliminary stage; descriptions for such subsystems are therefore provided in more detail than others to provide complete documentation of the work performed. In some cases, preliminary design parameters require specific verificaton in the definitive design phase and are identified in the text. Subsystem descriptions will continue to be issued and revised separately to maintain accuracy during future phases of the project. (WHK)

None,

1979-01-01T23:59:59.000Z

227

Optimized Fan Control In Variable Air Volume HVAC Systems Using Static Pressure Resets: Strategy Selection and Savings Analysis  

E-Print Network (OSTI)

The potential of static pressure reset (SPR) control to save fan energy in variable air volume HVAC systems has been well documented. Current research has focused on the creation of reset strategies depending on specific system features. As the commissioning process has begun to require the prediction of savings, knowledge of the extent to which various SPR control strategies impact fan energy has become increasingly important. This research aims to document existing SPR control strategies and utilize building data and simulation to estimate fan energy use. A comprehensive review of the literature pertaining to SPR control was performed and the results were organized into a top-down flow chart tool. Based on the type of feedback available from a particular system, or lack thereof, this tool will facilitate the selection of a SPR control strategy. A field experiment was conducted on a single duct variable air volume system with fixed discharge air temperature and static pressure setpoints. Finally, an air-side model of the experimental system was created using detailed building design information and calibrated using field measurements. This model was used to estimate the fan energy required to supply the trended airflow data using fixed static pressure (FSP) and SPR control based on zone demand, system demand, and outside air temperature. While utilizing trend data from November 1, 2008 to February 12, 2009, the FSP control of the experimental system was used as the baseline for ranking the energy savings potential of nine different forms of duct static pressure control. The highest savings (73-74%) were achieved using zonal demand based SPR control. System demand based SPR control yielded savings ranging from 59 to 76%, which increased when the duct sensor was positioned near the fan discharge and under similar zone load conditions. The outside air temperature based SPR control yielded savings of 65% since the experimental system supplied primarily perimeter zones. Finally, increasing the FSP setpoint from 2 to 3 inWG increased fan energy by 45%, while decreasing the setpoint from 2 to 1 inWG decreased fan energy by 41%.

Kimla, John

2009-12-01T23:59:59.000Z

228

SOLERAS - Solar Controlled Environment Agriculture Project. Final report, Volume 5. Science Applications, Incorporated system requirements definition  

DOE Green Energy (OSTI)

This report sets forth the system requirements for a Solar Controlled-Environment Agriculture System (SCEAS) Project. In the report a conceptual baseline system description for an engineering test facility is given. This baseline system employs a fluid roof/roof filter in combination with a large storage tank and a ground water heat exchanger in order to provide cooling and heating as needed. Desalination is accomplished by pretreatment followed by reverse osmosis. Energy is provided by means of photovoltaics and wind machines in conjunction with storage batteries. Site and climatic data needed in the design process are given. System performance specifications and integrated system design criteria are set forth. Detailed subsystem design criteria are presented and appropriate references documented.

Not Available

1985-01-01T23:59:59.000Z

229

Reliability-economics analysis models for photovoltaic power systems. Volume 2. [SOLREL  

DOE Green Energy (OSTI)

This report describes the development of modeling techniques to characterize the reliability, availability, and maintenance costs of photovoltaic power systems. The developed models can be used by designers of PV systems in making design decisions and trade-offs to minimize life-cycle energy costs. Three actual intermediate PV system designs were modeled as examples. The input data estimates used and the results of the analyses are presented.

Stember, L.H.; Huss, W.R.; Bridgman, M.S.

1982-11-01T23:59:59.000Z

230

Preliminary environmental assessment for the satellite power system (SPS). Revision 1. Volume 1. Executive summary  

DOE Green Energy (OSTI)

A preliminary assessment of the environmental impacts of the proposed satellite power system (SPS) is summarized here. In this system, satellites would collect solar energy in space, convert it to microwaves, and transmit the microwaves to receiving antennas (rectennas) on earth. At the rectennas, the microwaves would be converted to electricity. The assessment considers microwave and nonmicrowave effects on the terrestrial environment and human health, atmospheric effects, and disruption of communications and other electromagnetic systems.

Not Available

1980-01-01T23:59:59.000Z

231

Radioisotope thermoelectric generator transportation system safety analysis report for packaging. Volumes 1 and 2  

Science Conference Proceedings (OSTI)

This SARP describes the RTG Transportation System Package, a Type B(U) packaging system that is used to transport an RTG or similar payload. The payload, which is included in this SARP, is a generic, enveloping payload that specifically encompasses the General Purpose Heat Source (GPHS) RTG payload. The package consists of two independent containment systems mounted on a shock isolation transport skid and transported within an exclusive-use trailer.

Ferrell, P.C.

1996-04-18T23:59:59.000Z

232

Distributed Energy Systems in California's Future: A Preliminary Report Volume 2  

E-Print Network (OSTI)

Systems . District Solar Heating Biomass Conversion WindPacific Regional Solar Heating Handbook, San Francisco,Institutions About Solar Heating in the Home. Draft Report

Balderston, F.

2010-01-01T23:59:59.000Z

233

DISTRIBUTED ENERGY SYSTEMS IN CALIFORNIA'S FUTURE: A PRELIMINARY REPORT, VOLUME I  

E-Print Network (OSTI)

Water Heating . Passive Solar Heating of Buildings. SolarSite Solar Systems District Solar Heating Biomass ConversionBalcom, Pacific Regional Solar Heating Handbook, available

Authors, Various

2010-01-01T23:59:59.000Z

234

Distributed Energy Systems in California's Future: A Preliminary Report Volume 2  

E-Print Network (OSTI)

Electrification in Energy Systems", Paper presented at OakPublic Acceptance of Energy Conservation" paper presented atUniversity in The Energy Conservation Papers, Robert H.

Balderston, F.

2010-01-01T23:59:59.000Z

235

System 80+{trademark} standard design: CESSAR design certification. Volume 15: Amendment I  

Science Conference Proceedings (OSTI)

This report has been prepared in support of the industry effort to standardize nuclear plant designs. These documents describe the Combustion Engineering, Inc. System 80+{trademark} Standard Design.

Not Available

1990-12-21T23:59:59.000Z

236

Distributed Energy Systems in California's Future: A Preliminary Report Volume 2  

E-Print Network (OSTI)

Hot-Water Heating and Space Conditioning Systems in Northernprocess heating, and space conditioning designed to utilizeprocesses or for space conditioning. nologies refer to the

Balderston, F.

2010-01-01T23:59:59.000Z

237

Dynamic modeling and global optimal operation of multizone variable air volume HVAC systems.  

E-Print Network (OSTI)

??Energy conservation and indoor environment concerns have motivated extensive research on various aspects of control of Heating, Ventilating and Air-Conditioning (HVAC) and building systems. The (more)

Zheng, Guo Rong

1997-01-01T23:59:59.000Z

238

Distributed Energy Systems in California's Future: A Preliminary Report Volume 2  

E-Print Network (OSTI)

systems employing non-renewable energy sources in the finalwith traditional non-renewable energy forms. Thesetime perspective all non-renewable sources of energy are

Balderston, F.

2010-01-01T23:59:59.000Z

239

Distributed Energy Systems in California's Future: A Preliminary Report Volume 2  

E-Print Network (OSTI)

consideration of solar absorption cooling systems becomesStorage (80%) Solar Absorption Cooling (.31) Parabolicgeneration. For absorption cooling, the summer energy

Balderston, F.

2010-01-01T23:59:59.000Z

240

Final Report: Mobile Surveillance and Wireless Communication Systems Field Operational Test; Volume 1: Executive Summary  

E-Print Network (OSTI)

Design and Operation The mobile surveillance and wirelessAND WIRELESS COMMUNICATION SYSTEM DESIGN AND OPERATION.with camera operation. Mobile Surveillance and Wireless

Klein, Lawrence

1999-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

The integration of renewable energy sources into electric power distribution systems. Volume 2, Utility case assessments  

Science Conference Proceedings (OSTI)

Electric utility distribution system impacts associated with the integration of renewable energy sources such as photovoltaics (PV) and wind turbines (WT) are considered in this project. The impacts are expected to vary from site to site according to the following characteristics: (1) The local solar insolation and/or wind characteristics; (2) renewable energy source penetration level; (3) whether battery or other energy storage systems are applied; and (4) local utility distribution design standards and planning practices. Small, distributed renewable energy sources are connected to the utility distribution system like other, similar kW- and MW-scale equipment and loads. Residential applications are expected to be connected to single-phase 120/240-V secondaries. Larger kw-scale applications may be connected to three-phase secondaries, and larger hundred-kW and MW-scale applications, such as MW-scale windfarms or PV plants, may be connected to electric utility primary systems via customer-owned primary and secondary collection systems. Small, distributed renewable energy sources installed on utility distribution systems will also produce nonsite-specific utility generation system benefits such as energy and capacity displacement benefits, in addition to the local site-specific distribution system benefits. Although generation system benefits are not site-specific, they are utility-specific, and they vary significantly among utilities in different regions. In addition, transmission system benefits, environmental benefits and other benefits may apply. These benefits also vary significantly among utilities and regions. Seven utility case studies considering PV, WT, and battery storage were conducted to identify a range of potential renewable energy source distribution system applications.

Zaininger, H.W.; Ellis, P.R.; Schaefer, J.C. [Zaininger Engineering Co., San Jose, CA (United States)

1994-06-01T23:59:59.000Z

242

Central Receiver Solar Thermal Power System, Phase 1. CDRL Item 2. Pilot Plant preliminary design report. Volume III, Book 1. Collector subsystem  

DOE Green Energy (OSTI)

The central receiver system consists of a field of heliostats, a central receiver, a thermal storage unit, an electrical power generation system, and balance of plant. This volume discusses the collector field geometry, requirements and configuration. The development of the collector system and subsystems are discussed and the selection rationale outlined. System safety and availability are covered. Finally, the plans for collector portion of the central receiver system are reviewed.

Hallet, Jr., R. W.; Gervais, R. L.

1977-10-01T23:59:59.000Z

243

Proceedings of the third biennial conference and workshop on wind energy conversion systems. Volume I  

DOE Green Energy (OSTI)

Separate abstracts are included for 38 papers presented concerning large scale wind systems, small scale wind systems, regional and economic analysis, wind characteristics research, environmental and institutional considerations, and international activities. Four papers were previously input into the energy data base.

Kornreich, T R [ed.

1978-05-01T23:59:59.000Z

244

Reliability-economics analysis models for photovoltaic power systems. Volume 1  

DOE Green Energy (OSTI)

This report describes the development of modeling techniques to characterize the reliability, availability, and maintenance costs of photovoltaic power systems. The developed models can be used by designers of PV systems in making design decisions and trade-offs to minimize life-cycle energy costs.

Stember, L.H.; Huss, W.R.; Bridgman, M.S.

1982-11-01T23:59:59.000Z

245

Proceedings: Conference on Coal Gasification Systems and Synthetic Fuels for Power Generation, Volumes 1 and 2  

Science Conference Proceedings (OSTI)

The international effort to develop synthetic fuels and advanced power systems for the commercial generation of electric power from coal, oil shale, and tar sands has been an outstanding technical success. This conference highlighted the work that brought new fuels and power generation systems to reality.

1986-01-01T23:59:59.000Z

246

Energy storage and power conditioning aspects of photovoltaic solar power systems. Volume I. First quarterly report  

SciTech Connect

Solar energy may be utilized as thermal energy or converted into electricity by solar cells. ERDA's National Photovoltaic Conversion Program is concerned with this latter approach and is currently sponsoring industrial programs for photovoltaic systems and devices. In one such program, Spectrolab, Inc., is charged with performing conceptual design and analysis of three photovoltaic solar power systems. The sizes of these three systems will cover the requirements of residential, commercial and electric utility central station applications. In addition to a solar cell array, photovoltaic power systems must also include an energy storage system to enable operation during periods of low insolation and a power conditioning system to control the dc power from the array and convert it into an ac waveshape compatible with existing electrical equipment. The Scientific Development Operation of Bechtel Corporation is participating in the Spectrolab program by compiling and studying data on the energy storage and power conditioning aspects of all three photovoltaic solar power systems and by the conceptual design of the system for electric utility central station applications. The results of the energy storage and power conditioning study effort are presented in this report. (W.D.M.)

1975-10-01T23:59:59.000Z

247

Energy storage and power conditioning aspects of photovoltaic solar power systems. Volume I. First quarterly report  

DOE Green Energy (OSTI)

Solar energy may be utilized as thermal energy or converted into electricity by solar cells. ERDA's National Photovoltaic Conversion Program is concerned with this latter approach and is currently sponsoring industrial programs for photovoltaic systems and devices. In one such program, Spectrolab, Inc., is charged with performing conceptual design and analysis of three photovoltaic solar power systems. The sizes of these three systems will cover the requirements of residential, commercial and electric utility central station applications. In addition to a solar cell array, photovoltaic power systems must also include an energy storage system to enable operation during periods of low insolation and a power conditioning system to control the dc power from the array and convert it into an ac waveshape compatible with existing electrical equipment. The Scientific Development Operation of Bechtel Corporation is participating in the Spectrolab program by compiling and studying data on the energy storage and power conditioning aspects of all three photovoltaic solar power systems and by the conceptual design of the system for electric utility central station applications. The results of the energy storage and power conditioning study effort are presented in this report. (W.D.M.)

Not Available

1975-10-01T23:59:59.000Z

248

Institutional applications of solar total-energy systems. Draft final report. Volume 2. Appendixes  

DOE Green Energy (OSTI)

The appendices present the analytical basis for the analysis of solar total energy (STE) systems. A regional-climate model and a building-load requirements model are developed, along with fuel-price scenarios. Life-cycle costs are compared for conventional-utility, total energy, and STE systems. Thermal STE system design trade-offs are performed and thermal STE system performance is determined. The sensitivity of STE competitiveness to fuel prices is examined. The selection of the photovoltaic array is briefly discussed. The institutional-sector decision processes are analyzed. Hypothetical regional back-up rates and electrical-energy costs are calculated. The algorithms and equations used in operating the market model are given, and a general methodology is developed for projecting the size of the market for STE systems and applied to each of 8 institutional subsectors. (LEW)

None

1978-07-01T23:59:59.000Z

249

SOLERAS - Solar Controlled Environment Agriculture Project. Final report, Volume 6. Science Applications, Incorporated system analysis  

Science Conference Proceedings (OSTI)

This report summarizes the results of the systems analysis task for the conceptual design of a commercial size, solar powered, controlled environment agriculture system. The baseline greenhouse system consists of a 5-hectare growing facility utilizing an innovative fluid roof filter concept to provide temperature and humidity control. Fresh water for the system is produced by means of a reverse osmosis desalination unit and energy is provided by means of a solar photovoltaic array in conjunction with storage batteries and a power conditioning unit. The greenhouse environment is controlled via circulation of brackish groundwater in a closed system, which permits water recovery during dehumidification as well as CO/sub 2/ enrichment for increased crop productivity.

Not Available

1985-01-01T23:59:59.000Z

250

Technical and economic assessment of fluidized bed augmented compressed air energy-storage system. Volume II. Introduction and technology assessment  

DOE Green Energy (OSTI)

The results are described of a study subcontracted by PNL to the United Technologies Research Center on the engineering feasibility and economics of a CAES concept which uses a coal fired, fluidized bed combustor (FBC) to heat the air being returned from storage during the power production cycle. By burning coal instead of fuel oil, the CAES/FBC concept can completely eliminate the dependence of compressed air energy storage on petroleum fuels. The results of this assessment effort are presented in three volumes. Volume II presents a discussion of program background and an in-depth coverage of both fluid bed combustion and turbomachinery technology pertinent to their application in a CAES power plant system. The CAES/FBC concept appears technically feasible and economically competitive with conventional CAES. However, significant advancement is required in FBC technology before serious commercial commitment to CAES/FBC can be realized. At present, other elements of DOE, industrial groups, and other countries are performing the required R and D for advancement of FBC technology. The CAES/FBC will be reevaluated at a later date when FBC technology has matured and many of the concerns now plaguing FBC are resolved. (LCL)

Giramonti, A.J.; Lessard, R.D.; Merrick, D.; Hobson, M.J.

1981-09-01T23:59:59.000Z

251

Preliminary environmental assessment for the satellite power system (SPS). Volume 1. Executive summary  

DOE Green Energy (OSTI)

A summary of the preliminary assessment of the environmental impacts of a SPS is given. Microwave health and ecological effects, other effects on health and the environment, effects on the atmosphere, and effects on communications systems are summarized. (WHK)

Not Available

1978-10-01T23:59:59.000Z

252

''Rancho Hydro'': a low-head, high volume residential hydroelectric power system, Anahola, Kauai, Hawaii  

DOE Green Energy (OSTI)

The site is a 1.75 acre residential site with two households. The Anahola stream intersects the property line. Design of the proposed hydroelectric system is described, along with the permit process. Construction is in progress. (DLC)

Harder, J.D.

1982-07-01T23:59:59.000Z

253

Mission analysis of photovoltaic solar energy systems. Final report. Volume II. Technical report  

DOE Green Energy (OSTI)

Appendices include (1) demand forecasting methodologies, (2) system simulation model, (3) preliminary investigation of residential use of dc power, (4) power plant economic model, and (5) projections of unit fuel prices to the year 2000. (WHK)

Not Available

1975-12-01T23:59:59.000Z

254

Proceedings of the 7th international joint conference on Autonomous agents and multiagent systems - Volume 1  

Science Conference Proceedings (OSTI)

AAMAS is the premier scientific conference for research in autonomous agents and multiagent systems. The AAMAS conference series was initiated in 2002 as a merger of three highly respected individual conferences: the International Conference on Autonomous ...

Lin Padgham; David Parkes

2008-05-01T23:59:59.000Z

255

A system for high-volume acquisition and matching of fresco fragments: reassembling Theran wall paintings  

Science Conference Proceedings (OSTI)

Although mature technologies exist for acquiring images, geometry, and normals of small objects, they remain cumbersome and time-consuming for non-experts to employ on a large scale. In an archaeological setting, a practical acquisition system for routine ...

Benedict J. Brown; Corey Toler-Franklin; Diego Nehab; Michael Burns; David Dobkin; Andreas Vlachopoulos; Christos Doumas; Szymon Rusinkiewicz; Tim Weyrich

2008-08-01T23:59:59.000Z

256

Proceedings of the third biennial conference and workshop on wind energy conversion systems. Volume II  

DOE Green Energy (OSTI)

Separate abstracts are included for 34 papers presented concerning technology development, meteorological siting considerations, multi-unit applications, and innovative and advanced systems concepts. Two papers were previously input into the energy data base.

Kornreich, T R [ed.

1978-05-01T23:59:59.000Z

257

Handbook for Verification and Validation of Digital Systems, Volume 1: Revision 1  

Science Conference Proceedings (OSTI)

With the increasing use of digital instrumentation and control systems in power plants, utilities must determine the dependability and predictability of such systems and their software. This updated handbook provides a comprehensive guide to help utilities understand the verification and validation (V&V) process. The handbook presents a graded approach to select convenient V&V methods, develop a V&V plan, generate necessary documentation, and conduct appropriate V&V activities.

1998-12-15T23:59:59.000Z

258

Handbook for Verification and Validation of Digital Systems, Volume 2: Case Histories  

Science Conference Proceedings (OSTI)

With the increasing use of digital instrumentation and control systems in power plants, utilities must determine the dependability and predictability of such systems and their software. This updated handbook provides a comprehensive guide to help utilities understand the verification and validation (V&V) process. The handbook presents a graded approach to select convenient V&V methods, develop a V&V plan, generate necessary documentation, and conduct appropriate V&V activities.

1998-12-15T23:59:59.000Z

259

Review of thermally regenerative electrochemical systems. Volume I. Synopsis and executive summary  

SciTech Connect

Thermally regenerative electrochemical systems (TRES) are closed systems that convert heat into electricity in an electrochemical heat engine that is Carnot cycle limited in efficiency. Past and present work on such systems is reviewed. Two broad classes of TRES are based on the types of energy inputs required for regeneration: thermal alone and coupled thermal and electrolytic. The thermal regeneration alone encompasses electrochemical systems (galvanic or fuel cells) in which one or more products are formed. The regeneration can be performed in single or multiple steps. The compounds include metal hydrides, halides, oxides, chalcogenides, and alloys or bimetallic systems. The coupled thermal and electrolytic regeneration encompasses electrochemical systems (galvanic or fuel cells) regenerated by electrolysis at a different temperature or different pressure. Examples include metal halides and water. Thermogalvanic or nonisothermal cells are included in this category. Also included are electrochemical engines in which the working electroactive fluid is isothermally expanded through an electrolyte. TRES cover temperature ranges from about 20/sup 0/C to 1000/sup 0/C. Engines with power outputs of 0.1 mW/cm/sup 2/ to 1 W/cm/sup 2/ have been demonstrated. Recommendations are made of areas of research in science and engineering that would have long-range benefit to a TRES program.

Chum, H. L.; Osteryoung, R. A.

1980-08-01T23:59:59.000Z

260

A Management and Selection System for R&D Projects, Volume I - Overview  

DOE Green Energy (OSTI)

This report describes an RCD project management and selection system developed for the Utilization Technology Branch of the Division of Geothermal Energy, Department of Energy. The proposed project management system (PMS) consists of a project data system (PDS) and a project selection procedure (PSP). The project data system consists of a series of project data forms and project status logs, and descriptions of information pathways. The PDS emphasizes timely monitoring of the technical and financial progress of projects, maintenance of the history of the project and rapid access to project information to facilitate responsive reporting to DGE and DOE upper management. The project selection procedure emphasizes an RCD product-oriented approach to benefit/cost analysis of individual projects. The report includes: (a) a description of the system, and recommendations for its implementation, (b) the PDS forms and an explanation of their use, (c) a glossary of terms for use on the forms, (d) a description of the benefit/cost approach, (e) a data base for estimating RCD benefits, and (f) examples of test applications of the system to nine current DGE projects.

Dhillon, Harpal S.; Entingh, Daniel J.

1978-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

6000 tpd SRC-I Demonstration Plant gas systems. Design baseline package, Volume 8. [DEA process  

SciTech Connect

Volume 8 contains the design of the fuel gas desulfurization process (DEA) and of the liquefied petroleum gases (LPG) section of the plant. The removal of acid gases is accomplished by intimately contacting the feed stream with the descending DEA solution. A partially regenerated semi-lean DEA solution is fed to an intermediate tray of the column for the bulk removal of H/sub 2/S and CO/sub 2/ while a fully regenerated lean DEA solution is fed at the top tray for the removal of the remaining acid gases in the top section of the absorber. The lean solution stream temperature is maintained at 10 to 15/sup 0/F above the absorber feed gas temperature to prevent hydrocarbon condensation in the column with consequent foaming and flooding of the column. The overhead gas (Stream 6305) leaving the H.P. DEA absorber is cooled and passed through the Sweet Gas K.O. Drum (bottom section of V-15305) to separate any condensate. The gas leaving the drum is further contacted with a 3 weight percent caustic solution in the bottom section of the Treated Gas Wash Column (T-15303) for removal of residual acid gases in order to comply with the sweet gas specifications of 1 ppMv H/sub 2/S and 10 ppMv CO/sub 2/. The LPG Recovery Unit is designed to process 15.95 MMSCFD of low pressure fuel reject gas from the HPU to recover approximately 60 percent of the propane and most of the heavier hydrocarbons. The recovered hydrocarbons are produced as liquefied petroleum gas (LPG) product. Specifications for the LPG product are: (1) Ethane/Propane (Vol/Vol) 0.02; and (2) LPG product should meet GPA Publication 2140-77 Commercial B-P mixture specifications.

1983-01-27T23:59:59.000Z

262

Transportation Sector Model of the National Energy Modeling System. Volume 2 -- Appendices: Part 2  

Science Conference Proceedings (OSTI)

The attachments contained within this appendix provide additional details about the model development and estimation process which do not easily lend themselves to incorporation in the main body of the model documentation report. The information provided in these attachments is not integral to the understanding of the model`s operation, but provides the reader with opportunity to gain a deeper understanding of some of the model`s underlying assumptions. There will be a slight degree of replication of materials found elsewhere in the documentation, made unavoidable by the dictates of internal consistency. Each attachment is associated with a specific component of the transportation model; the presentation follows the same sequence of modules employed in Volume 1. The following attachments are contained in Appendix F: Fuel Economy Model (FEM)--provides a discussion of the FEM vehicle demand and performance by size class models; Alternative Fuel Vehicle (AFV) Model--describes data input sources and extrapolation methodologies; Light-Duty Vehicle (LDV) Stock Model--discusses the fuel economy gap estimation methodology; Light Duty Vehicle Fleet Model--presents the data development for business, utility, and government fleet vehicles; Light Commercial Truck Model--describes the stratification methodology and data sources employed in estimating the stock and performance of LCT`s; Air Travel Demand Model--presents the derivation of the demographic index, used to modify estimates of personal travel demand; and Airborne Emissions Model--describes the derivation of emissions factors used to associate transportation measures to levels of airborne emissions of several pollutants.

NONE

1998-01-01T23:59:59.000Z

263

Verification and validation guidelines for high integrity systems: Appendices A--D, Volume 2  

SciTech Connect

The following material is furnished as an experimental guide for the use of risk based classification for nuclear plant protection systems. As shown in Sections 2 and 3 of this report, safety classifications for the nuclear field are application based (using the function served as the primary criterion), whereas those in use by the process industry and the military are risk based. There are obvious obstacles to the use of risk based classifications (and the associated integrity levels) for nuclear power plants, yet there are also many potential benefits, including: it considers all capabilities provided for dealing with a specific hazard, thus assigning a lower risk where multiple protection is provided (either at the same or at lower layers); this permits the plant management to perform trade-offs between systems that meet the highest qualification levels or multiple diverse systems at lower qualification levels; it motivates the use (and therefore also the development) of protection systems with demonstrated low failure probability; and it may permit lower cost process industry equipment of an established integrity level to be used in nuclear applications (subject to verification of the integrity level and regulatory approval). The totality of these benefits may reduce the cost of digital protection systems significantly an motivate utilities to much more rapid upgrading of the capabilities than is currently the case. Therefore the outline of a risk based classification is presented here, to serve as a starting point for further investigation and possible trial application.

Hecht, H,; Hecht, M.; Dinsmore, G.; Hecht, S.; Tang, D. [SoHaR, Inc., Beverly Hills, CA (United States)

1995-03-01T23:59:59.000Z

264

Artificial heart development program. Volume I. System development. Phase III summary report  

SciTech Connect

The report documents efforts and results in the development of the power system portions of a calf implantable model of nuclear-powered artificial heart. The primary objective in developing the implantable model was to solve the packaging problems for total system implantation. The power systems portion is physically that portion of the implantable model between the Pu-238 heat sources and the blood pump ventricles. The work performed had two parallel themes. The first of these was the development of an integrated implantable model for bench and animal experiments plus design effort on a more advanced model. The second was research and development on components of the system done in conjunction with the development of the implantable model and to provide technology for incorporation into advanced models plus support to implantations, at the University of Utah, of the systems blood pumping elements when driven by electric motor. The efforts and results of implantable model development are covered, mainly, in the text of the report. The research and development efforts and results are reported, primarily, in the appendices (Vol. 2).

1977-01-01T23:59:59.000Z

265

Proceedings of the coal-fired power systems 94: Advances in IGCC and PFBC review meeting. Volume 2  

Science Conference Proceedings (OSTI)

The Coal-Fired Power Systems 94 -- Advances in IGCC and PFBC Review Meeting was held June 21--23, 1994, at the Morgantown Energy Center (METC) in Morgantown, West Virginia. This Meeting was sponsored and hosted by METC, the Office of Fossil Energy, and the US Department of Energy (DOE). METC annually sponsors this conference for energy executives, engineers, scientists, and other interested parties to review the results of research and development projects; to discuss the status of advanced coal-fired power systems and future plans with the industrial contractors; and to discuss cooperative industrial-government research opportunities with METC`s in-house engineers and scientists. Presentations included industrial contractor and METC in-house technology developments related to the production of power via coal-fired Integrated Gasification Combined Cycle (IGCC) and Pressurized Fluidized Bed Combustion (PFBC) systems, the summary status of clean coal technologies, and developments and advancements in advanced technology subsystems, such as hot gas cleanup. A keynote speaker and other representatives from the electric power industry also gave their assessment of advanced power systems. This meeting contained 11 formal sessions and one poster session, and included 52 presentations and 24 poster presentations. Volume II contains papers presented at the following sessions: filter technology issues; hazardous air pollutants; sorbents and solid wastes; and membranes. Selected papers have been processed separately for inclusion in the Energy Science and Technology Database.

McDaniel, H.M.; Staubly, R.K.; Venkataraman, V.K. [eds.

1994-06-01T23:59:59.000Z

266

Applied research on energy storage and conversion for photovoltaic and wind energy systems. Volume III. Wind conversion systems with energy storage. Final report  

DOE Green Energy (OSTI)

The variability of energy output inherent in wind energy conversion systems (WECS) has led to the investigation of energy storage as a means of managing the available energy when immediate, direct use is not possible or desirable. This portion of the General Electric study was directed at an evaluation of those energy storage technologies deemed best suited for use in conjunction with a wind energy conversion system in utility, residential and intermediate applications. Break-even cost goals are developed for several storage technologies in each application. These break-even costs are then compared with cost projections presented in Volume I of this report to show technologies and time frames of potential economic viability. The report summarizes the investigations performed and presents the results, conclusions and recommendations pertaining to use of energy storage with wind energy conversion systems.

Not Available

1978-01-01T23:59:59.000Z

267

System component compatibility and R-114 stability. Volume II. Final report  

DOE Green Energy (OSTI)

High temperature stability-compatibility studies of R-114 refrigerant and proposed Sperry Geothermal System components were performed. The R-114 refrigerant, geothermal brine, and ten lubricants were tested in the presence of five metals, eight metal alloys, two ceramics, two iron oxides, and twenty-two elastomers in several combinations, temperature levels, and durations. Compatibility experiments of elastomers and non-elastomeric sealants in aqueous solutions and lubricating oils were performed. The development of the downwell packer necessitated the completion of an elastomer formulation development program. The system component material selection and specifications for the pump system are given. The seal material selection for the stand-alone turbine-pump-unit is presented in detail.

Goodson, J.E. Jr.; Nowicki, D.F.; Thibeau, R.J.; Toekes, B.; Wilson, D.P.

1981-01-01T23:59:59.000Z

268

Building America Best Practices Series, Volume 6: High-Performance Home Technologies: Solar Thermal & Photovoltaic Systems  

SciTech Connect

This guide is was written by PNNL for the US Department of Energy's Building America program to provide information for residential production builders interested in building near zero energy homes. The guide provides indepth descriptions of various roof-top photovoltaic power generating systems for homes. The guide also provides extensive information on various designs of solar thermal water heating systems for homes. The guide also provides construction company owners and managers with an understanding of how solar technologies can be added to their homes in a way that is cost effective, practical, and marketable. Twelve case studies provide examples of production builders across the United States who are building energy-efficient homes with photovoltaic or solar water heating systems.

Baechler, Michael C.; Gilbride, Theresa L.; Ruiz, Kathleen A.; Steward, Heidi E.; Love, Pat M.

2007-06-04T23:59:59.000Z

269

Building America Best Practices Series, Volume 6: High-Performance Home Technologies: Solar Thermal & Photovoltaic Systems  

SciTech Connect

This guide is was written by PNNL for the US Department of Energy's Building America program to provide information for residential production builders interested in building near zero energy homes. The guide provides indepth descriptions of various roof-top photovoltaic power generating systems for homes. The guide also provides extensive information on various designs of solar thermal water heating systems for homes. The guide also provides construction company owners and managers with an understanding of how solar technologies can be added to their homes in a way that is cost effective, practical, and marketable. Twelve case studies provide examples of production builders across the United States who are building energy-efficient homes with photovoltaic or solar water heating systems.

Baechler, Michael C.; Gilbride, Theresa L.; Ruiz, Kathleen A.; Steward, Heidi E.; Love, Pat M.

2007-06-04T23:59:59.000Z

270

Guidelines for the verification and validation of expert system software and conventional software: Survey and documentation of expert system verification and validation methodologies. Volume 3  

SciTech Connect

This report is the third volume in the final report for the Expert System Verification and Validation (V&V) project which was jointly sponsored by the Nuclear Regulatory Commission and the Electric Power Research Institute. The ultimate objective is the formulation of guidelines for the V&V of expert systems for use in nuclear power applications. The purpose of this activity was to survey and document techniques presently in use for expert system V&V. The survey effort included an extensive telephone interviewing program, site visits, and a thorough bibliographic search and compilation. The major finding was that V&V of expert systems is not nearly as established or prevalent as V&V of conventional software systems. When V&V was used for expert systems, it was almost always at the system validation stage after full implementation and integration usually employing the non-systematic dynamic method of {open_quotes}ad hoc testing.{close_quotes} There were few examples of employing V&V in the early phases of development and only weak sporadic mention of the possibilities in the literature. There is, however, a very active research area concerning the development of methods and tools to detect problems with, particularly, rule-based expert systems. Four such static-testing methods were identified which were not discovered in a comprehensive review of conventional V&V methods in an earlier task.

Groundwater, E.H.; Miller, L.A.; Mirsky, S.M. [Science Applications International Corp., McLean, VA (United States)

1995-03-01T23:59:59.000Z

271

Preliminary Systems Design Study assessment report. Volume 5, Land disposal compliance and hydrogen generation restricted concepts  

SciTech Connect

The System Design Study (SDS), part of the Waste Technology Development Department at the Idaho National Engineering Laboratory (INEL), examined techniques available for the remediation of hazardous and transuranic waste stored at the Radioactive Waste Management Complex`s Subsurface Disposal Area at the INEL. Using specific technologies, system concepts for treating the buried waste and the surrounding contaminated soil were evaluated. Evaluation included implementability, effectiveness, and cost. The SDS resulted in the development of technology requirements including demonstration, testing, and evaluation activities needed for implementing each concept.

Mayberry, J.L.; Feizollahi, F.; Del Signore, J.C.

1991-11-01T23:59:59.000Z

272

Evaluation of solar radiation measurement systems: EPRI/NREL final test report. Volume 1  

DOE Green Energy (OSTI)

Measured solar radiation resource data are needed by electric utilities to evaluate the potential of renewable energy options like photovoltaics in their service territory. In this final test report, we document a cooperative project of the Electric Power Research Institute (EPRI) and the National Renewable Energy Laboratory (NREL) to compare available measurement system options for performing solar radiation resource assessments. We present the detailed results of a 6-month field comparison of thermopile-based pyranometer and pyrheliometer solar irradiance measurement systems with two different implementations of the rotating shadowband radiometer (RSR) concept installed at NREL`s Solar Radiation Research Laboratory (SRRL) in Golden, Colorado.

Stoffel, T.; Riordan, C.; Bigger, J.

1992-11-01T23:59:59.000Z

273

Irreversible volume growth in polymer-bonded powder systems: effects of crystalline anisotropy, particle size distribution, and binder strength  

Science Conference Proceedings (OSTI)

Pressed-powdered crystallites of intrinsically anisotropic materials have been shown to undergo irreversible volume expansion when subjected to repeated cycles of heating and cooling. We develop a coarse-grained (micron-scale) interaction Hamiltonian for this system and perform molecular dynamics simulations, which quantitatively reproduce the experimentally observed irreversible growth. The functional form and values of the interaction parameters at the coarse-grained level are motivated by our knowledge at the atomic/molecular scale, and allows a simple way to incorporate the effect of polymeric binder. We demonstrate that irreversible growth happens only in the presence of intrinsic crystalline anisotropy of the powder material, is mediated by particles much smaller than the average crystallite size, and can be significantly reduced in the presence of high-strength polymeric binder with elevated glass transition temperatures.

Maiti, A; Gee, R H; Hoffman, D; Fried, L E

2007-08-22T23:59:59.000Z

274

Thermal power systems: Small Power Systems Applications Project. Volume II. Detailed report. Annual technical report, fiscal year 1978  

SciTech Connect

Small Power Systems Applications activities for FY 1978 are reported. Studies were conducted to address current small power system technology as applied to power plants up to 10 MWe in size. Markets for small power systems were characterized and cost goals were established for the project. Candidate power plant system design concepts were selected for evaluation and preliminary performance and cost assessments were made. Economic studies were conducted at JPL and under contract to Burns and McDonnell. Breakeven capital costs were determined for leading contenders among the candidate systems. An applications study was made of the potential use of small power systems in providing part of the demand for pumping power by the extensive aqueduct system of California, estimated to be 1000 MWe by 1985. Criteria and methodologies were developed for application to the ranking of candidate power plant system design concepts. Experimental power plants concepts of 1 MWe rating were studied by three contractors as a Phase I effort leading toward the definition of a power plant configuration for subsequent detail design, construction, testing and evaluation as Engineering Experiment No. 1 (EE No. 1). Site selection criteria and ground rules for the solicitation of EE No. 1 site participation proposals by DOE were developed.

1979-01-15T23:59:59.000Z

275

Nuclear proliferation and civilian nuclear power. Report of the Nonproliferation Alternative Systems Assessment Program. Volume V. Economics and systems analysis  

SciTech Connect

This NASAP assessment considers the economics of alternative nuclear reactor and fuel-cycle systems in the light of possible patterns of uranium supply and energy demand, as well as the economic implications of improvng the proliferation resistance of the various systems. The assessment focuses on the costs of alternative nuclear technologies and the possible timing of their implementation, based on their economic attractiveness.

1980-06-01T23:59:59.000Z

276

Full-System Decontamination of a BWR Using the LOMI Process Volume 3: Decontamination Equipment and System Interaction  

Science Conference Proceedings (OSTI)

The LOMI (low-oxidation-state metal-ion) dilute-chemical-decontamination process has been qualified for use on the complete reactor system of BWRs. Full-system decontamination offers several economic and operational advantages over current partsystem applications. This study provides the technical basis for a safety evaluation.

1991-10-30T23:59:59.000Z

277

Multi-Mode Transportable Battery Energy System for Salt River Project: Volume 1: Design and Installation  

Science Conference Proceedings (OSTI)

Energy storage technologies are likely to find new roles in a restructured electric utility environment. This project designed and deployed a commercial prototype of an innovative multi-mode transportable battery system capable of a broad functional role in the new business environment.

1999-06-29T23:59:59.000Z

278

The 10th International Conference on Autonomous Agents and Multiagent Systems - Volume 3  

Science Conference Proceedings (OSTI)

The Autonomous Agents and MultiAgent Systems (AAMAS) conference series brings together researchers from around the world to share the latest advances in the field. It provides a marquee, high-profile forum for research in the theory and practice of autonomous ...

Kagan Tumer; Pinar Yolum; Liz Sonenberg; Peter Stone

2011-05-01T23:59:59.000Z

279

The 10th International Conference on Autonomous Agents and Multiagent Systems - Volume 2  

Science Conference Proceedings (OSTI)

The Autonomous Agents and MultiAgent Systems (AAMAS) conference series brings together researchers from around the world to share the latest advances in the field. It provides a marquee, high-profile forum for research in the theory and practice of autonomous ...

Kagan Tumer; Pinar Yolum; Liz Sonenberg; Peter Stone

2011-05-01T23:59:59.000Z

280

Proceedings of The 8th International Conference on Autonomous Agents and Multiagent Systems - Volume 1  

Science Conference Proceedings (OSTI)

In the beginning of the 21th century, the success of the so-called information society has changed dramatically both the requirements and the main characteristics of most computer-based systems. The previous century saw a migration from huge mainframes ...

Carles Sierra; Cristiano Castelfranchi; Keith S. Decker; Jaime Simo Sichman

2009-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

The 10th International Conference on Autonomous Agents and Multiagent Systems - Volume 1  

Science Conference Proceedings (OSTI)

The Autonomous Agents and MultiAgent Systems (AAMAS) conference series brings together researchers from around the world to share the latest advances in the field. It provides a marquee, high-profile forum for research in the theory and practice of autonomous ...

Kagan Tumer; Pinar Yolum; Liz Sonenberg; Peter Stone

2011-05-01T23:59:59.000Z

282

Bases for solid waste volume estimates for tank waste remediation system  

Science Conference Proceedings (OSTI)

This document presents the background and basis for the Tank Waste Remediation System forecast for solid waste submitted in June 1996. The forecast was generated for single-shell tank and double-shell tank activities including operations through retrieval and disposal of chemical tank waste.

Reddick, G.W., Westinghouse Hanford

1996-08-01T23:59:59.000Z

283

Proceedings of the 11th International Conference on Autonomous Agents and Multiagent Systems - Volume 1  

Science Conference Proceedings (OSTI)

The Autonomous Agents and MultiAgent Systems (AAMAS) conference series brings together researchers from around the world to share the latest advances in the field. It provides a high-profile and high-quality forum for research in the theory and practice ...

Vincent Conitzer; Michael Winikoff; Wiebe van der Hoek; Lin Padgham

2012-06-01T23:59:59.000Z

284

Application analysis of solar total energy systems to the residential sector. Volume IV, market penetration. Final report  

DOE Green Energy (OSTI)

This volume first describes the residential consumption of energy in each of the 11 STES regions by fuel type and end-use category. The current and projected costs and availability of fossil fuels and electricity for the STES regions are reported. Projections are made concerning residential building construction and the potential market for residential STES. The effects of STES ownership options, institutional constraints, and possible government actions on market penetration potential were considered. Capital costs for two types of STES were determined, those based on organic Rankine cycle (ORC) heat engines and those based on flat plate, water-cooled photovoltaic arrays. Both types of systems utilized parabolic trough collectors. The capital cost differential between conventional and STE systems was calculated on an incremental cost per dwelling unit for comparison with projected fuel savings in the market penetration analysis. The market penetration analysis was planned in two phases, a preliminary analysis of each of the geographical regions for each of the STE systems considered; and a final, more precise analysis of those regions and systems showing promise of significant market penetration. However, the preliminary analysis revealed no geographical regions in which any of the STES considered promised to be competitive with conventional energy systems using utility services at the prices projected for future energy supplies in the residential market. Because no promising situations were found, the analysis was directed toward an examination of the parameters involved in an effort to identify those factors which make a residential STES less attractive than similar systems in the commercial and industrial areas. Results are reported. (WHK)

Not Available

1979-07-01T23:59:59.000Z

285

(BARS) -- Bibliographic Retrieval System Sandia shock compression (SSC) database shock physics index (SPHINX) database. Volume 3, UNIX version Systems Guide  

SciTech Connect

The Bibliographic Retrieval System (BARS) is a database management system specially designed to store and retrieve bibliographic references and track documents. The system uses INGRES to manage this database and user interface. It uses forms for journal articles, books, conference proceedings, theses, technical reports, letters, memos, visual aids, as well as a miscellaneous form which can be used for data sets or any other material which can be assigned an access or file number. Sorted output resulting from flexible BOOLEAN searches can be printed or saved in files which can be inserted in reference lists for use with word processors.

von Laven, G.M. [Advanced Software Engineering, Madison, AL (United States); Herrmann, W. [Sandia National Labs., Albuquerque, NM (United States)

1993-09-01T23:59:59.000Z

286

Study of transmission and protection elements for wind energy generating systems. Volume 1  

DOE Green Energy (OSTI)

Results are reported of a study at Cornell University on transmission, distribution, and protection systems for large wind-energy generators (WEG) connected to an electric utility grid. Configurations for wind farms on flat terrain, mountain-peak clusters, and installations along a ridge were examined. Computer studies of load-flow and short-circuit behavior confirmed the technical feasibility of the proposed systems. Realistic unit costs for the projected transmission and protection schemes range from $109 to $317 per Kw, depending upon choice of configuration and distance from the grid. Cost of protective equipment is found to be a major factor in most cases, tending to be equal or greater than transmission line costs when the WEG units are located five miles or less from the grid. Several alternatives are suggested for future study.

Linke, S; Teshome, A; Yehsakul, P D

1978-04-01T23:59:59.000Z

287

Mission analysis of photovoltaic solar energy systems. Final report. Volume I. Summary  

SciTech Connect

A summary report of a study program whose principal objective was to develop methods for the technical and economic evaluation of potential missions (applications) for photovoltaic solar energy conversion in the southwestern United States in the 1980 to 2000 period is presented. A secondary objective was to apply the methodology, when developed, to the evaluation of a number of illustrative examples of candidate missions in order to obtain at least a preliminary indication of the competitive position of the photovoltaic technology in the future energy economy of the Southwest. Because of their large potential significance, most of the effort in the study was devoted to two main classes of missions: on-site applications (in which the photovoltaic system serves an electric load point that is colocated with the system) and central station power plant applications. A smaller amount of attention was given to the electrolytic production of hydrogen with electric power generated by the photovoltaic conversion of solar energy. (WHK)

1975-12-01T23:59:59.000Z

288

MRS system study for the repository: Yucca Mountain Site Characterization Project; Volume 2  

SciTech Connect

The US Department of Energy (DOE), Office of Civilian Radioactive Waste Management (OCRWM), has initiated a waste management system study to identify the impacts of the presence or absence of a monitored retrievable storage facility (hereinafter referred to as ``MRS``) on system costs and program schedules. To support this study, life-cycle cost estimates and construction schedules have been prepared for the surface and underground facilities and operations geologic nuclear waste repository at Yucca Mountain, Nye County, Nevada. Nine different operating scenarios (cases) have been identified by OCRWM for inclusion in this study. For each case, the following items are determined: the repository design and construction costs, operating costs, closure and decommissioning costs, required staffing, construction schedules, uncertainties associated with the costs and schedules, and shipping cask and disposal container throughputs. This document contains A-D.

Sinagra, T.A. [Bechtel National, Inc., San Francisco, CA (USA); Harig, R. [Parsons, Brinckerhoff, Quade and Douglas, Inc., San Francisco, CA (USA)

1990-12-01T23:59:59.000Z

289

Automated energy management systems for small buildings. Final report, Volume 1: technical document  

SciTech Connect

Energy controls can perform a valuable function in energy conservation or energy-management strategy in buildings. While the more-simple controls can be applied to virtually any building, the more-complex automation systems are currently available only to large buildings where their greater costs may be justified. At the present, however, there is a lack of effective, automatic energy-management control practices and schemes available for application to small buildings. This is due, in large measure, to the absence of cost-effective integrated control equipment in the small-building marketplace. Furthermore, a general philosophy or strategy, for the application of equipment for total energy conservation in small commercial buildings has not yet evolved. Both technical and marketing issues related to the implementation of automation systems in small commercial buildings under 75,000 square feet gross area are explored. The functional requirements for small-building automation systems are identified and determination of system costs and energy savings potential are made. Market analyses identify cost and payback requirements as well as attitudes of potential equipment buyers in the small-building market. Schools, apartments, and offices, which together consume more than half the energy of the small-building market, are used as analysis models. The market and technical analyses are combined to formulate the potential marketplace for a small building AEMS in terms of building size, and building type. An AEMS concept is defined which embodies the necessary functional requirements within a framework of applied strategy to energy conservation in buildings.

1978-08-01T23:59:59.000Z

290

Commercial applications of solar total energy systems. Volume 3. Conceptual designs and market analyses. Final report  

DOE Green Energy (OSTI)

The overall objective of this program was to assess the feasibility of using solar energy to provide a significant fraction of the energy needs of commercial buildings that have energy demands greater than 200 kWe. The STES concept trade studies, sensitivity parameters, performance characteristics, and selected concepts are discussed. Market penetration rate estimates are provided, and technology advancements and utilization plans are discussed. Photovoltaic STES configurations and Rankine cycle thermal STES systems are considered. (WHK)

Boobar, M.G.; McFarland, B.L.; Nalbandian, S.J.; Willcox, W.W.; French, E.P.; Smith, K.E.

1978-07-01T23:59:59.000Z

291

Assessment of solar options for small power systems applications. Volume I. Executive summary  

DOE Green Energy (OSTI)

A comparative analysis of solar thermal conversion concepts that are potentially suitable for development as small electric power systems (1 to 10 MWe) is presented. Seven generic types of collectors, together with associated subsystems for electric power generation, were considered. The collectors can be classified into three categories: (1) two-axis tracking (with compound-curvature reflecting surfaces), (2) one-axis tracking (with single-curvature reflecting surfaces), and (3) nontracking (with low-concentration reflecting surfaces). All seven collectors were analyzed in conceptual system configurations with Rankine-cycle engines. In addition, two of the collectors (the Point Focus Central Receiver and the Point Focus Distributed Receiver) were analyzed with Brayton-cycle engines, and the latter of the two also was analyzed with Stirling-cycle engines. With these engine options, 10 systems were formulated for analysis. Conceptual designs developed for the 10 systems were based on common assumptions of available technology in the 1990 to 2000 time frame. The computer code SOLSTEP was used to analyze the thermodynamic performance characteristics and energy costs of the 10 concepts. Year-long simulations were performed using meteorological and insolation data for Barstow, California as input to the code. Results for each concept include levelized energy costs and capacity factors for various combinations of storage capacity and collector field size. For all 10 concepts, subjective values were estimated for four additional power plant characteristics: plant flexibility, forced outage rate, environmental and safety effects, and R and D necessary for commercialization. Multiattribute utility methodology was used to rank the 10 concepts. (WHK)

Laity, W.W.; Aase, D.T.; Apley, W.J.; Bird, S.P.; Currie, J.W.; Drost, M.K.; Jannol, M.; Schulte, S.C.; Sutey, A.M.; Williams, T.A.

1979-09-01T23:59:59.000Z

292

California Regional Wind Energy Forecasting System Development, Volume 1: Executive Summary  

Science Conference Proceedings (OSTI)

The rated capacity of wind generation in California is expected to grow rapidly in the future beyond the approximately 2100 megawatts (MW) in place at the end of 2005. The main drivers are the state's 20 Renewable Portfolio Standard requirement in 2010 and the low cost of wind energy relative to other renewable energy sources. As wind is an intermittent generation resource and weather changes can cause large and rapid changes in output, system operators will need accurate and robust wind energy forecasti...

2006-11-14T23:59:59.000Z

293

California Regional Wind Energy Forecasting System Development, Volume 4: California Wind Generation Research Dataset (CARD)  

Science Conference Proceedings (OSTI)

The rated capacity of wind generation in California is expected to grow rapidly in the future beyond the approximately 2100 megawatts in place at the end of 2005. The main drivers are the state's 20 percent renewable portfolio standard requirement in 2010 and the low cost of wind energy relative to other renewable energy sources. As wind is an intermittent generation resource and weather changes can cause large and rapid changes in output, system operators will need accurate and robust wind energy forec...

2006-11-13T23:59:59.000Z

294

Commercial applications of solar total energy systems. Volume 1. Summary. Final report  

DOE Green Energy (OSTI)

A methodology has been developed by Atomics International under contract to the Department of Energy to define the applicability of solar total energy systems (STES) to the commercial sector (e.g., retail stores, shopping centers, offices, etc.) in the United States. Candidate STES concepts were selected to provide on-site power generation capability, as well as thermal energy for both heating and cooling applications. Each concept was evaluated on the basis of its cost effectiveness (i.e., as compared to other concepts) and its ability to ultimately penetrate and capture a significant segment of this market, thereby resulting in a saving of fossil fuel resources. The photovoltaic STES appears favorable for applications under 800 kWe; whereas the organic Rankine STES would be more cost effective for larger energy demand applications. Initial penetration of these systems are expected to occur in the northeast for large shopping centers in the 1990 to 2000 time period. Such systems could provide about 0.8 to 1.8 quads (8 x 10/sup 14/ to 1.8 x 10/sup 15/ Btu) of energy per year for commercial applictions by the year 2010.

Boobar, M.G.; McFarland, B.L.; Nalbandian, S.J.; Willcox, W.W.; French, E.P.; Smith, K.E.

1978-07-01T23:59:59.000Z

295

Operating experience feedback report -- turbine-generator overspeed protection systems: Commercial power reactors. Volume 11  

SciTech Connect

This report presents the results of the US Nuclear Regulatory Commission`s Office for Analysis and Evaluation of Operational Data (AEOD) review of operating experience of main turbine-generator overspeed and overspeed protection systems. It includes an indepth examination of the turbine overspeed event which occurred on November 9, 1991, at the Salem Unit 2 Nuclear Power Plant. It also provides information concerning actions taken by other utilities and the turbine manufacturers as a result of the Salem overspeed event. AEOD`s study reviewed operating procedures and plant practices. It noted differences between turbine manufacturer designs and recommendations for operations, maintenance, and testing, and also identified significant variations in the manner that individual plants maintain and test their turbine overspeed protection systems. AEOD`s study provides insight into the shortcomings in the design, operation, maintenance, testing, and human factors associated with turbine overspeed protection systems. Operating experience indicates that the frequency of turbine overspeed events is higher than previously thought and that the bases for demonstrating compliance with NRC`s General Design Criterion (GDC) 4, Environmental and dynamic effects design bases, may be nonconservative with respect to the assumed frequency.

Ornstein, H.L.

1995-04-01T23:59:59.000Z

296

Generation IV Nuclear Energy Systems Ten-Year Program Plan Fiscal Year 2005, Volume 1  

SciTech Connect

As reflected in the U.S. ''National Energy Policy'', nuclear energy has a strong role to play in satisfying our nation's future energy security and environmental quality needs. The desirable environmental, economic, and sustainability attributes of nuclear energy give it a cornerstone position, not only in the U.S. energy portfolio, but also in the world's future energy portfolio. Accordingly, on September 20, 2002, U.S. Energy Secretary Spencer Abraham announced that, ''The United States and nine other countries have agreed to develop six Generation IV nuclear energy concepts''. The Secretary also noted that the systems are expected to ''represent significant advances in economics, safety, reliability, proliferation resistance, and waste minimization''. The six systems and their broad, worldwide research and development (R&D) needs are described in ''A Technology Roadmap for Generation IV Nuclear Energy Systems'' (hereafter referred to as the Generation IV Roadmap). The first 10 years of required U.S. R&D contributions to achieve the goals described in the Generation IV Roadmap are outlined in this Program Plan.

None

2005-03-01T23:59:59.000Z

297

User manual for GEOCITY: a computer model for cost analysis of geothermal district-heating-and-cooling systems. Volume II. Appendices  

DOE Green Energy (OSTI)

The purpose of this model is to calculate the costs of residential space heating, space cooling, and sanitary water heating or process heating (cooling) using geothermal energy from a hydrothermal reservoir. The model can calculate geothermal heating and cooling costs for residential developments, a multi-district city, or a point demand such as an industrial factory or commercial building. Volume II contains all the appendices, including cost equations and models for the reservoir and fluid transmission system and the distribution system, descriptions of predefined residential district types for the distribution system, key equations for the cooling degree hour methodology, and a listing of the sample case output. Both volumes include the complete table of contents and lists of figures and tables. In addition, both volumes include the indices for the input parameters and subroutines defined in the user manual.

Huber, H.D.; Fassbender, L.L.; Bloomster, C.H.

1982-09-01T23:59:59.000Z

298

Comparative ranking of 0. 1 to 10 MW(e) solar thermal electric power systems. Volume I. Summary of results. Final report  

DOE Green Energy (OSTI)

This report is part of a two-volume set summarizing the results of a comparative ranking of generic solar thermal concepts designed specifically for electric power generation. The original objective of the study was to project the mid-1990 cost and performance of selected generic solar thermal electric power systems for utility applications and to rank these systems by criteria that reflect their future commercial acceptance. This study considered plants with rated capacities of 1 to 10 MW(e), operating over a range of capacity factors from the no-storage case to 0.7 and above. Later, the study was extended to include systems with capacities from 0.1 to 1 MW(e), a range that is attractive to industrial and other non-utility applications. This volume summarizes the results for the full range of capacities from 0.1 to 10 MW(e). Volume II presents data on performance and cost and ranking methodology.

Thornton, J.P.; Brown, K.C.; Finegold, J.G.; Gresham, J.B.; Herlevich, F.A.; Kowalik, J.S.; Kriz, T.A.

1980-08-01T23:59:59.000Z

299

DEVELOPMENT OF A NATURAL GAS SYSTEMS ANALYSIS MODEL (GSAM) VOLUME I - SUMMARY REPORT VOLUME II - USER'S GUIDE VOLUME IIIA - RP PROGRAMMER'S GUIDE VOLUME IIIB - SRPM PROGRAMMER'S GUIDE VOLUME IIIC - E&P PROGRAMMER'S GUIDE VOLUME IIID - D&I PROGRAMMER'S GUIDE  

SciTech Connect

This report summarizes work completed on DOE Contract DE-AC21-92MC28138, Development of a Natural Gas Systems Analysis Model (GSAM). The products developed under this project directly support the National Energy Technology Laboratory (NETL) in carrying out its natural gas R&D mission. The objective of this research effort has been to create a comprehensive, non-proprietary, microcomputer model of the North American natural gas market. GSAM has been developed to explicitly evaluate components of the natural gas system, including the entire in-place gas resource base, exploration and development technologies, extraction technology and performance parameters, transportation and storage factors, and end-use demand issues. The system has been fully tested and calibrated and has been used for multiple natural gas metrics analyses at NETL in which metric associated with NETL natural gas upstream R&D technologies and strategies under the direction of NETL has been evaluated. NETL's Natural Gas Strategic Plan requires that R&D activities be evaluated for their ability to provide adequate supplies of reasonably priced natural gas. GSAM provides the capability to assess potential and on-going R&D projects using a full fuel cycle, cost-benefit approach. This method yields realistic, market-based assessments of benefits and costs of alternative or related technology advances. GSAM is capable of estimating both technical and commercial successes, quantifying the potential benefits to the market, as well as to other related research. GSAM, therefore, represents an integration of research activities and a method for planning and prioritizing efforts to maximize benefits and minimize costs. Without an analytical tool like GSAM, NETL natural gas upstream R&D activities cannot be appropriately ranked or focused on the most important aspects of natural gas extraction efforts or utilization considerations.

Unknown

2001-02-01T23:59:59.000Z

300

EIS-0285: Final Environmental Impact Statement, Volume 2 | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Volume 2 EIS-0285: Final Environmental Impact Statement, Volume 2 Bonneville Power Administration Transmission System Vegetation Management Program Volume 2: Appendices Appendix A...

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Model documentation: Natural gas transmission and distribution model of the National Energy Modeling System. Volume 1  

SciTech Connect

The Natural Gas Transmission and Distribution Model (NGTDM) is the component of the National Energy Modeling System (NEMS) that is used to represent the domestic natural gas transmission and distribution system. NEMS was developed in the Office of integrated Analysis and Forecasting of the Energy information Administration (EIA). NEMS is the third in a series of computer-based, midterm energy modeling systems used since 1974 by the EIA and its predecessor, the Federal Energy Administration, to analyze domestic energy-economy markets and develop projections. The NGTDM is the model within the NEMS that represents the transmission, distribution, and pricing of natural gas. The model also includes representations of the end-use demand for natural gas, the production of domestic natural gas, and the availability of natural gas traded on the international market based on information received from other NEMS models. The NGTDM determines the flow of natural gas in an aggregate, domestic pipeline network, connecting domestic and foreign supply regions with 12 demand regions. The methodology employed allows the analysis of impacts of regional capacity constraints in the interstate natural gas pipeline network and the identification of pipeline capacity expansion requirements. There is an explicit representation of core and noncore markets for natural gas transmission and distribution services, and the key components of pipeline tariffs are represented in a pricing algorithm. Natural gas pricing and flow patterns are derived by obtaining a market equilibrium across the three main elements of the natural gas market: the supply element, the demand element, and the transmission and distribution network that links them. The NGTDM consists of four modules: the Annual Flow Module, the Capacity F-expansion Module, the Pipeline Tariff Module, and the Distributor Tariff Module. A model abstract is provided in Appendix A.

NONE

1995-02-17T23:59:59.000Z

302

Volume Tracking  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Total Volumes Captured on both Enterprise & Q4000" Total Volumes Captured on both Enterprise & Q4000" ,"Daily Period",,"Containment Total" ,"Oil","Gas","Oil","Gas" "End Period","Recovery","Recovery","Recovery","Recovery" "Date and Time","Rate","Rate","Cumulative","Cumulative" "MM/DD/YY 00:00","(bo)","(mmcf)","(bbls)","(mmcf)","Comment" 40333,16.486,0,16.486,0,"Oil rate based on metered volume" 40334,6060.70543,15.666,6077.19143,15.666,"Oil rate based on metered volume" 40335,10496.19429,22.00800001,16573.38572,37.674,"Oil rate based on metered volume"

303

Experience Based Seismic Verification Guidelines for Overhead Crane Systems: Volume I - Seismic Review Procedure; Volume II - Performance of Overhead Cranes in Strong Motion Earthquakes  

Science Conference Proceedings (OSTI)

This report provides guidelines that can be used to perform an experience-based seismic capability verification of overhead cranes systems at nuclear power plants. The report summarizes seismic experience data from strong-motion earthquakes for these systems and identifies the characteristics of systems that could lead to failure or unacceptable behavior in an earthquake. The seismic experience data show that overhead crane systems exhibit extremely good performance under strong-motion seismic loading, w...

2005-06-08T23:59:59.000Z

304

Economic evaluation of the Annual Cycle Energy System (ACES). Volume II. Detailed results. Final report  

Science Conference Proceedings (OSTI)

The energy effectiveness and the economic viability of the ACES concept are examined. ACES is studied in a variety of different applications and compared to a number of conventional systems. The different applications are studied in two groups: the class of building into which the ACES is incorporated and the climatic region in which the ACES is located. Buildings investigated include single-family and multi-family residences and a commercial office building. The application of ACES to each of these building types is studied in Minneapolis, Atlanta, and Philadelphia. The economic evaluation of the ACES is based on a comparison of the present worth of the ACES to the present worth of conventional systems; namely, electric resistance heating, electric air conditioning, and electric domestic water heating; air-to-air heat pump and electric domestic water heating; oil-fired furnace, electric air conditioning, and electric domestic water heating; and gas-fired furnace, electric air conditioning, and gas domestic water heating.

Not Available

1980-05-01T23:59:59.000Z

305

Natural Gas Transmission and Distribution Model of the National Energy Modeling System. Volume 1  

Science Conference Proceedings (OSTI)

The Natural Gas Transmission and Distribution Model (NGTDM) is the component of the National Energy Modeling System (NEMS) that is used to represent the domestic natural gas transmission and distribution system. The NGTDM is the model within the NEMS that represents the transmission, distribution, and pricing of natural gas. The model also includes representations of the end-use demand for natural gas, the production of domestic natural gas, and the availability of natural gas traded on the international market based on information received from other NEMS models. The NGTDM determines the flow of natural gas in an aggregate, domestic pipeline network, connecting domestic and foreign supply regions with 12 demand regions. The purpose of this report is to provide a reference document for model analysts, users, and the public that defines the objectives of the model, describes its basic design, provides detail on the methodology employed, and describes the model inputs, outputs, and key assumptions. Subsequent chapters of this report provide: an overview of NGTDM; a description of the interface between the NEMS and NGTDM; an overview of the solution methodology of the NGTDM; the solution methodology for the Annual Flow Module; the solution methodology for the Distributor Tariff Module; the solution methodology for the Capacity Expansion Module; the solution methodology for the Pipeline Tariff Module; and a description of model assumptions, inputs, and outputs.

NONE

1998-01-01T23:59:59.000Z

306

The Coastal Ocean Prediction Systems program: Understanding and managing our coastal ocean. Volume 1: Strategic summary  

SciTech Connect

The proposed COPS (Coastal Ocean Prediction Systems) program is concerned with combining numerical models with observations (through data assimilation) to improve our predictive knowledge of the coastal ocean. It is oriented toward applied research and development and depends upon the continued pursuit of basic research in programs like COOP (Coastal Ocean Processes); i.e., to a significant degree it is involved with ``technology transfer`` from basic knowledge to operational and management applications. This predictive knowledge is intended to address a variety of societal problems: (1) ship routing, (2) trajectories for search and rescue operations, (3) oil spill trajectory simulations, (4) pollution assessments, (5) fisheries management guidance, (6) simulation of the coastal ocean`s response to climate variability, (7) calculation of sediment transport, (8) calculation of forces on structures, and so forth. The initial concern is with physical models and observations in order to provide a capability for the estimation of physical forces and transports in the coastal ocean. For all these applications, there are common needs for physical field estimates: waves, tides, currents, temperature, and salinity, including mixed layers, thermoclines, fronts, jets, etc. However, the intent is to work with biologists, chemists, and geologists in developing integrated multidisciplinary prediction systems as it becomes feasible to do so. From another perspective, by combining observations with models through data assimilation, a modern approach to monitoring is provided through whole-field estimation.

Not Available

1990-05-15T23:59:59.000Z

307

Small power systems study technical summary report. Volume II. Inventory of small generating units in U. S. utility systems  

SciTech Connect

Data identifying small (less than or equal to 10 MW) power units in the United States are tabulated. The data are listed alphabetically by state and are reported sequentially for investor owned utilities, municipal utilities, and electrical cooperatives and other utility systems. For a given utility system, the generating units are divided into steam turbines, diesel generators and gas turbines. The number and size of generating units are listed. A summary tabulation of the number of generating units of each type and total generating capacity by state is presented.

Sitney, L.R.

1978-05-31T23:59:59.000Z

308

NDN, volume transmission, and self-organization in brain dynamics  

E-Print Network (OSTI)

NDN, VOLUME TRANSMISSION, AND SELF- ORGANIZATION IN BRAINThese systems instantiate volume transmission bynonsynaptic diffusion transmission, in concert with the

Freeman, Walter J III

2005-01-01T23:59:59.000Z

309

Long range forecast of power demands on the Baltimore Gas and Electric Company system. Volume 1  

SciTech Connect

The report presents the results of an econometric forecast of peak and electric power demands for the Baltimore Gas and Electric Company (BGandE) through the year 2003. The report describes the methodology, the results of the econometric estimations and associated summary statistics, the forecast assumptions, and the calculated forecasts of energy usage and peak demand. Separate models were estimated for summer and winter residential electricity usage in both Baltimore city and the non-city portion of the BGandE service area. Equations were also estimated for commercial energy usage, industrial usage, streetlighting, and for losses plus Company use. Non-econometric techniques were used to estimate future energy use by Bethlehem Steel Corporation's Sparrows Point plant in Baltimore County, Conrail, and the Baltimore Mass Transit Administration underground rail system. Models of peak demand for summer and winter were also estimated.

Estomin, S.L.; Kahal, M.I.

1985-09-01T23:59:59.000Z

310

Energy Research Information System. Projects report. Volume 2, Number 4. Cumulative Indexes (Project Nos. 00000540 through 00001080)  

SciTech Connect

The Cumulative Indexes include a state-location index, a personal name index, an organization index and a subject keyword index incorporating the indexes from ERIS Volume 2, Nos. 1, 2, and 3. This issue, plus the entire contents of Volume 1 and Volume 2, comprise a set of 1080 research project references for the states of the Old West region - Montana, Nebraska, North Dakota, South Dakota and Nebraska.

Boyd, C.A.; Schillinger, L.A.

1977-12-01T23:59:59.000Z

311

Should we have a new engine. An automobile power systems evaluation. Volume II. Technical reports  

SciTech Connect

Alternative automotive powerplants were examined for possible introduction during the 1980 to 1990 time period. Technical analyses were made of the stratified-charge Otto, diesel, Rankine (steam), Brayton (gas turbine), Stirling, electric, and hybrid powerplants as alternatives to the conventional Otto-cycle engine with its likely improvements. These alternatives were evaluated from a societal point of view in terms of energy consumption, urban air quality, cost to the consumer, materials availability, safety, and industry impact. The results show that goals for emission reduction and energy conservation for the automobile over the next 5 to 10 years can be met by improvements to the Otto-cycle engine and to the vehicle. This provides time for the necessary development work on the Brayton and Stirling engines, which offer the promise of eliminating the automobile as a significant source of urban air pollution, dramatically reducing fuel consumption, and being saleable at a price differential which can be recovered in fuel savings by the first owner. Specifically, the Brayton and Stirling engines require intensive component, system, and manufacturing process development at a funding level considerably higher than at present.

Stephenson, R.R.

1975-01-01T23:59:59.000Z

312

Innovative coke oven gas cleaning system for retrofit applications. Volume 1, Public design report  

SciTech Connect

This Public Design Report provides, in a single document, available nonproprietary design -information for the ``Innovative Coke Oven Gas Cleaning System for Retrofit Applications`` Demonstration Project at Bethlehem Steel Corporation`s Sparrows Point, Maryland coke oven by-product facilities. This project demonstrates, for the first time in the United States, the feasibility of integrating four commercially available technologies (processes) for cleaning coke oven gas. The four technologies are: Secondary Gas Cooling, Hydrogen Sulfide and Ammonia Removal, Hydrogen Sulfide and Ammonia Recovery, and Ammonia Destruction and Sulfur Recovery. In addition to the design aspects, the history of the project and the role of the US Department of,Energy are briefly discussed. Actual plant capital and projected operating costs are also presented. An overview of the integration (retrofit) of the processes into the existing plant is presented and is followed by detailed non-proprietary descriptions of the four technologies and their overall effect on reducing the emissions of ammonia, sulfur, and other pollutants from coke oven gas. Narrative process descriptions, simplified process flow diagrams, input/output stream data, operating conditions, catalyst and chemical requirements, and utility requirements are given for each unit. Plant startup provisions, environmental considerations and control monitoring, and safety considerations are also addressed for each process.

Not Available

1994-05-24T23:59:59.000Z

313

Power-generation alternatives. The Hellenic power system. Volume 1. Executive Summary. Export trade information  

Science Conference Proceedings (OSTI)

The Phase I study was performed to assist the Public Power Corporation (PPC) of Greece in making decisions regarding the need for new power generation or for repowering existing facilities. An analysis of both new power generation requirements and the feasibility of repowering the existing Aliveri and St. George Stations with coal is provided. The study concludes: Repowering of Aliveri Units 3 and 4 with coal should commence now. Present and committed capacity of the PPC system is adequate until 1997 to 1999, at which time a new 600 MW pulverized coal boiler unit at the Aliveri Station would be commissioned. St. George Station has very little possibility for siting of coal-based new generation or repowering. New facilities should be designed for imported coal to conserve lignite resources for existing and committed units. An alternative to PPC ownership is private sector ownership. A Phase II study for repowering should be initiated and funded by PPC following acceptance of the Phase I study.

Not Available

1987-06-01T23:59:59.000Z

314

Analysis techniques for power substation grounding systems. Volume 2. User's manual  

SciTech Connect

This User's Manual is provided as an adjunct to the final report on EPRI Research Project 1494-2. The manual is a self-contained document intended to provide detailed and complete instruction on the use of the computer programs developed by the research project. The manual includes user documentation on the two computer programs, entitled SGSYS and SMECC, developed on the contract. Brief program descriptions are followed by operational instructions, data formats, and output specifications. Preceding the program documentation is an introductory section which defines terms and outlines basic elements of grounding system analysis. Following this, a simple but detailed example is given which may be used as a guide in program utilization and also as a test case for individual program users. Following the user documentation is a completed practical example which shows data preparation for a specific substation and computer results obtained for that substation. The example also provides suggested procedures in approaching the problem of substation design using the methodologies developed by this project.

Joy, E.B.; Meliopoulos, A.P.; Webb, R.P.

1983-08-01T23:59:59.000Z

315

Assessment of solar options for small power systems applications. Volume V. SOLSTEP: a computer model for solar plant system simulations  

DOE Green Energy (OSTI)

The simulation code, SOLSTEP, was developed at the Pacific Northwest Laboratory to facilitate the evaluation of proposed designs for solar thermal power plants. It allows the user to analyze the thermodynamic and economic performance of a conceptual design for several field size-storage capacity configurations. This feature makes it possible to study the levelized energy cost of a proposed concept over a range of plant capacity factors. The thermodynamic performance is analyzed on a time step basis using actual recorded meteorological and insolation data for specific geographic locations. The flexibility of the model enables the user to analyze both central and distributed generation concepts using either thermal or electric storage systems. The thermodynamic and economic analyses view the plant in a macroscopic manner as a combination of component subsystems. In the thermodynamic simulation, concentrator optical performance is modeled as a function of solar position; other aspects of collector performance can optionally be treated as functions of ambient air temperature, wind speed, and component power level. The power conversion model accounts for the effects of ambient air temperature, partial load operation, auxiliary power demands, and plant standby and startup energy requirements. The code was designed in a modular fashion to provide efficient evaluations of the collector system, total plant, and system economics. SOLSTEP has been used to analyze a variety of solar thermal generic concepts involving several collector types and energy conversion and storage subsystems. The code's straightforward models and modular nature facilitated simple and inexpensive parametric studies of solar thermal power plant performance.

Bird, S.P.

1980-09-01T23:59:59.000Z

316

SCALE: A modular code system for performing standardized computer analyses for licensing evaluation. Functional modules F1--F8 -- Volume 2, Part 1, Revision 4  

SciTech Connect

SCALE--a modular code system for Standardized Computer Analyses Licensing Evaluation--has been developed by Oak Ridge National Laboratory at the request of the US Nuclear Regulatory Commission. The SCALE system utilizes well-established computer codes and methods within standard analysis sequences that (1) allow an input format designed for the occasional user and/or novice, (2) automate the data processing and coupling between modules, and (3) provide accurate and reliable results. System development has been directed at problem-dependent cross-section processing and analysis of criticality safety, shielding, heat transfer, and depletion/decay problems. Since the initial release of SCALE in 1980, the code system has been heavily used for evaluation of nuclear fuel facility and package designs. This revision documents Version 4.2 of the system. The manual is divided into three volumes: Volume 1--for the control module documentation; Volume 2--for functional module documentation; and Volume 3--for documentation of the data libraries and subroutine libraries.

Greene, N.M.; Petrie, L.M.; Westfall, R.M.; Bucholz, J.A.; Hermann, O.W.; Fraley, S.K. [Oak Ridge National Lab., TN (United States)

1995-04-01T23:59:59.000Z

317

Total-system performance assessment for Yucca Mountain - SNL second iteration (TSPA-1993); Volume 2  

Science Conference Proceedings (OSTI)

Sandia National Laboratories has completed the second iteration of the periodic total-system performance assessments (TSPA-93) for the Yucca Mountain Site Characterization Project (YMP). These analyses estimate the future behavior of a potential repository for high-level nuclear waste at the Yucca Mountain, Nevada, site under consideration by the Department of Energy. TSPA-93 builds upon previous efforts by emphasizing YMP concerns relating to site characterization, design, and regulatory compliance. Scenarios describing expected conditions (aqueous and gaseous transport of contaminants) and low-probability events (human-intrusion drilling and volcanic intrusion) are modeled. The hydrologic processes modeled include estimates of the perturbations to ambient conditions caused by heating of the repository resulting from radioactive decay of the waste. Hydrologic parameters and parameter probability distributions have been derived from available site data. Possible future climate changes are modeled by considering two separate groundwater infiltration conditions: {open_quotes}wet{close_quotes} with a mean flux of 10 mm/yr, and {open_quotes}dry{close_quotes} with a mean flux of 0.5 mm/yr. Two alternative waste-package designs and two alternative repository areal thermal power densities are investigated. One waste package is a thin-wall container emplaced in a vertical borehole, and the second is a container designed with corrosion-resistant and corrosion-allowance walls emplaced horizontally in the drift. Thermal power loadings of 57 kW/acre (the loading specified in the original repository conceptual design) and 114 kW/acre (a loading chosen to investigate effects of a {open_quotes}hot repository{close_quotes}) are considered. TSPA-93 incorporates significant new detailed process modeling, including two- and three-dimensional modeling of thermal effects, groundwater flow in the saturated-zone aquifers, and gas flow in the unsaturated zone.

Wilson, M.L.; Barnard, R.W.; Barr, G.E.; Dockery, H.A.; Dunn, E.; Eaton, R.R.; Martinez, M.J. [Sandia National Labs., Albuquerque, NM (United States); Gauthier, J.H.; Guerin, D.C.; Lu, N. [and others

1994-04-01T23:59:59.000Z

318

Total-system performance assessment for Yucca Mountain - SNL second iteration (TSPA-1993); Volume 1  

Science Conference Proceedings (OSTI)

Sandia National Laboratories has completed the second iteration of the periodic total-system performance assessments (TSPA-93) for the Yucca Mountain Site Characterization Project (YMP). These analyses estimate the future behavior of a potential repository for high-level nuclear waste at the Yucca Mountain, Nevada, site under consideration by the Department of Energy. TSPA-93 builds upon previous efforts by emphasizing YMP concerns relating to site characterization, design, and regulatory compliance. Scenarios describing expected conditions (aqueous and gaseous transport of contaminants) and low-probability events (human-intrusion drilling and volcanic intrusion) are modeled. The hydrologic processes modeled include estimates of the perturbations to ambient conditions caused by heating of the repository resulting from radioactive decay of the waste. Hydrologic parameters and parameter probability distributions have been derived from available site data. Possible future climate changes are modeled by considering two separate groundwater infiltration conditions: {open_quotes}wet{close_quotes} with a mean flux of 10 mm/yr, and {open_quotes}dry{close_quotes} with a mean flux of 0.5 mm/yr. Two alternative waste-package designs and two alternative repository areal thermal power densities are investigated. One waste package is a thin-wall container emplaced in a vertical borehole, and the second is a container designed with corrosion-resistant and corrosion-allowance walls emplaced horizontally in the drift. Thermal power loadings of 57 kW/acre (the loading specified in the original repository conceptual design) and 114 kW/acre (a loading chosen to investigate effects of a {open_quotes}hot repository{close_quotes}) are considered. TSPA-93 incorporates significant new detailed process modeling, including two- and three-dimensional modeling of thermal effects, groundwater flow in the saturated-zone aquifers, and gas flow in the unsaturated zone.

Wilson, M.L.; Gauthier, J.H.; Barnard, R.W.; Barr, G.E.; Dockery, H.A.; Dunn, E.; Eaton, R.R.; Guerin, D.C.; Lu, N.; Martinez, M.J. [and others] [and others

1994-04-01T23:59:59.000Z

319

Transportation Sector Model of the National Energy Modeling System. Volume 1  

SciTech Connect

This report documents the objectives, analytical approach and development of the National Energy Modeling System (NEMS) Transportation Model (TRAN). The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, model source code, and forecast results generated by the model. The NEMS Transportation Model comprises a series of semi-independent models which address different aspects of the transportation sector. The primary purpose of this model is to provide mid-term forecasts of transportation energy demand by fuel type including, but not limited to, motor gasoline, distillate, jet fuel, and alternative fuels (such as CNG) not commonly associated with transportation. The current NEMS forecast horizon extends to the year 2010 and uses 1990 as the base year. Forecasts are generated through the separate consideration of energy consumption within the various modes of transport, including: private and fleet light-duty vehicles; aircraft; marine, rail, and truck freight; and various modes with minor overall impacts, such as mass transit and recreational boating. This approach is useful in assessing the impacts of policy initiatives, legislative mandates which affect individual modes of travel, and technological developments. The model also provides forecasts of selected intermediate values which are generated in order to determine energy consumption. These elements include estimates of passenger travel demand by automobile, air, or mass transit; estimates of the efficiency with which that demand is met; projections of vehicle stocks and the penetration of new technologies; and estimates of the demand for freight transport which are linked to forecasts of industrial output. Following the estimation of energy demand, TRAN produces forecasts of vehicular emissions of the following pollutants by source: oxides of sulfur, oxides of nitrogen, total carbon, carbon dioxide, carbon monoxide, and volatile organic compounds.

NONE

1998-01-01T23:59:59.000Z

320

Robust, accurate, and non-contacting vibration measurement systems: Supplemental appendices presenting comparison measurements of the robust laser interferometer and typical accelerometer systems. Volume 2  

Science Conference Proceedings (OSTI)

Epoch Engineering, Incorporated (EEI) has completed a series of vibration measurements comparing their newly-developed Robust Laser Interferometer (RLI) with accelerometer-based instrumentation systems. EEI has successfully demonstrated, on several pieces of commonplace machinery, that non-contact, line-of-sight measurements are practical and yield results equal to or, in some cases, better than customary field implementations of accelerometers. The demonstration included analysis and comparison of such phenomena as nonlinearity, transverse sensitivity, harmonics, and signal-to-noise ratio. Fast Fourier Transformations were performed on the accelerometer and the laser system outputs to provide a comparison basis. The RLI was demonstrated, within the limits o the task, to be a viable, line-of-sight, non-contact alternative to accelerometer systems. Several different kinds of machinery were instrumented and. compared, including a small pump, a gear-driven cement mixer, a rotor kit, and two small fans. Known machinery vibration sources were verified and RLI system output file formats were verified to be compatible with commercial computer programs used for vibration monitoring and trend analysis. The RLI was also observed to be less subject to electromagnetic interference (EMI) and more capable at very low frequencies. This document, Volume 2, provides the appendices to this report.

Goodenow, T.C.; Shipman, R.L.; Holland, H.M. [Epoch Engineering, Inc., Gaithersburg, MD (United States)

1995-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

U.S. Department of Energy Space and Defense Power Systems Program Ten-Year Strategic Plan, Volume 1 and Volume 2  

SciTech Connect

The Department of Energy's Space and Defense Power Systems program provides a unique capability for supplying power systems that function in remote or hostile environments. This capability has been functioning since the early 1960s and counts the National Aeronautics and Space Administration as one of its most prominent customers. This enabling technology has assisted the exploration of our solar system including the planets Jupiter, Saturn, Mars, Neptune, and soon Pluto. This capability is one-of-kind in the world in terms of its experience (over five decades), breadth of power systems flown (over two dozen to date) and range of power levels (watts to hundreds of watts). This document describes the various components of that infrastructure, work scope, funding needs, and its strategic plans going forward.

Dwight, Carla

2013-06-01T23:59:59.000Z

322

Economic evaluation of the Annual Cycle Energy System. Volume I. Executive summary. Final report. [In Minneapolis, Atlanta, and Philadelphia  

Science Conference Proceedings (OSTI)

The objective of this study is to determine the energy effectiveness and the economic viability of the ACES concept. Three different classes of building are investigated, namely: single-family residence; multi-family residence; and commercial office building. The application of ACES to each of these building types is studied in three different climatic regions: Minneapolis, Atlanta, and Philadelphia. Computer programs - ACESIM for the residences and CACESS for the office building - were used, each comprised of four modules: loads; design; simulation; and economic. For each building type in each geographic location, the economic evaluation of the ACES is based on a comparison of the present worth of the ACES to the present worth of a number of conventional systems. The results of this analysis indicate that the economic viability of the ACES is very sensitive to the assumed value of the property tax, maintenace cost, and fuel-escalation rates, while it is relatively insensitive to the assumed values of other parameters. Fortunately, any conceivable change in the fuel-escalation rates would tend to increase the viability of the ACES concept. An increase in the assumed value of the maintenance cost or property tax would tend to make the ACES concept less viable; a decrease in either would tend to make the ACES concept more viable. The detailed results of this analysis are given in Section 5.4 of Volume II. 2 figures, 21 tables.

Not Available

1980-05-01T23:59:59.000Z

323

Conceptual design of advanced central receiver power systems sodium-cooled receiver concept. Volume 4. Commercial and pilot plant cost data. Final report  

DOE Green Energy (OSTI)

This volume of the advanced central receiver final report presents the cost data using the cost breakdown structure identified in the preliminary specification. Cost summaries are presented in the following sections for the 100-MWe and 281-MWe commercial plant and a 10-MWe pilot plant. Cost substantiation data for this volume are presented in the appendices. Other cost summary data include Nth plant data for the 100-MWe and 281-MWe commercial plants, and a summary for the alternative concept air-rock storage system. The main description of the plant costing technique occurs as part of Section II for the 100-MWe baseline concept.

Not Available

1979-03-01T23:59:59.000Z

324

Sperry Low Temperature Geothermal Conversion System, Phase 1 and Phase II. Final report. Volume III. Systems description  

DOE Green Energy (OSTI)

The major fraction of hydrothermal resources that have the prospect of being economically useful for the generation of electricity are in the 300/sup 0/F to 425/sup 0/F temperature range. Cost-effective conversion of the geothermal energy to electricity requires the conception and reduction to practice of new ideas to improve conversion efficiency, enhance brine flow, reduce plant costs, increase plant availability, and shorten the time between investment and return. The problems addressed during past activities are those inherent in the geothermal environment, in the binary fluid cycle, in the difficulty of efficiently converting the energy of a low-temperature resource, and in geothermal economics. Explained in detail in this document, some of these problems are: the energy expended by the down-hole pump; the difficulty in designing reliable down-hole equipment; fouling of heat-exchanger surfaces by geothermal fluids; the unavailability of condenser cooling water at most geothermal sites; the large portion of the available energy used by the feed pump in a binary system; the pinch effect - a loss in available energy in transferring heat from water to an organic fluid; flow losses in fluids that carry only a small amount of useful energy to begin with; high heat-exchanger costs - the lower the temperature interval of the cycle, the higher the heat exchanger costs in $/kW (actually, more than inversely proportional); the complexity and cost of the many auxiliary elements of proposed geothermal plants; and the unfortunate cash flow vs. investment curve caused by the many years of investment required to bring a field into production before any income is realized.

Matthews, H.B.

1984-01-01T23:59:59.000Z

325

Nuclear proliferation and civilian nuclear power. Report of the Nonproliferation Alternative Systems Assessment Program. Volume IX. Reactor and fuel cycle description  

SciTech Connect

The Nonproliferation Alterntive Systems Assessment Program (NASAP) has characterized and assessed various reactor/fuel-cycle systems. Volume IX provides, in summary form, the technical descriptions of the reactor/fuel-cycle systems studied. This includes the status of the system technology, as well as a discussion of the safety, environmental, and licensing needs from a technical perspective. This information was then used in developing the research, development, and demonstration (RD and D) program, including its cost and time frame, to advance the existing technology to the level needed for commercial use. Wherever possible, the cost data are given as ranges to reflect the uncertainties in the estimates.

Not Available

1980-06-01T23:59:59.000Z

326

Automated Registration of Volumes of Interest for a Combined X-Ray Tomosynthesis and Ultrasound Breast Imaging System  

Science Conference Proceedings (OSTI)

An intuitive display method was developed to enable a user to select and visualize corresponding volumes of interest in combined digital breast tomosynthesis (DBT) and automated breast ultrasound images. Details of this method are described including ...

Mitchell M. Goodsitt; Heang-Ping Chan; Lubomir Hadjiiski; Gerald L. Lecarpentier; Paul L. Carson

2008-07-01T23:59:59.000Z

327

Unsteady flow volumes  

SciTech Connect

Flow volumes are extended for use in unsteady (time-dependent) flows. The resulting unsteady flow volumes are the 3 dimensional analog of streamlines. There are few examples where methods other than particle tracing have been used to visualize time varying flows. Since particle paths can become convoluted in time there are additional considerations to be made when extending any visualization technique to unsteady flows. We will present some solutions to the problems which occur in subdivision, rendering, and system design. We will apply the unsteady flow volumes to a variety of field types including moving multi-zoned curvilinear grids.

Becker, B.G.; Lane, D.A.; Max, N.L.

1995-03-01T23:59:59.000Z

328

Emissions of volatile and potentially toxic organic compounds from waste-water treatment plants and collection systems (Phase 2). Volume 1. Project summaries. Final report  

SciTech Connect

The objectives of the Phase II research project on emission of potentially toxic organic compounds (PTOCs) from wastewater treatment plants were fivefold: (1) assessment of the importance of gaseous emissions from municipal wastewater collection systems; (2) resolution of the discrepancy between the measured and estimated emissions (Phase I), from the Joint Water Pollution Control Plant (JWPCP) operated by the County Sanitation Districts of Los Angeles County (CSDLAC); (3) determination of airborne concentrations of PTOCS immediately downwind of an activated sludge aeration process at the City of Los Angeles' Hyperion Treatment Plant (HTP); (4) a modeling assessment of the effects of transient loading on emissions during preliminary and primary treatment at a typical municipal wastewater treatment plant (MWTP); (5) a preliminary investigation of effects of chlorination practices on haloform production. Volume 1, for which the abstract was prepared, contains a summary of results from each project; Volume 2 contains the discussion regarding the modeling of collection system emissions; Volume 3 addresses methods development and field sampling efforts at the JWPCP and HTP, data on emissions from a mechanically ventilated sewer and results of some preliminary haloform formation studies in wastewaters; and Volume 4 discusses aspects of the emissions modeling problem.

Chang, D.P.Y.; Schroeder, E.D.; Corsi, R.L.; Guensler, R.; Meyerhofer, J.A.

1991-08-01T23:59:59.000Z

329

Blending of hydrogen in natural gas distribution systems. Volume I. Gas blends flow in distribution system, mixing points, and regulatory standards. Final report, June 1, 1976--August 30, 1977. [10 and 20% hydrogen  

DOE Green Energy (OSTI)

This volume of the subject study ''Blending of Hydrogen in Natural Gas Distribution Systems'' describes studies on the determination of gas distribution system flows with hydrogen - natural gas blends, potential hydrogen admission points to gas distribution systems, and the impact of hydrogen - natural gas blends on regulatory standards for gas distribution systems. The studies resulted in the following principal findings: (1) Most existing natural gas distribution systems could adequately transport 20% blends of hydrogen by volume with little or no modification. (2) The best point of admission of the hydrogen into a natural gas distribution system would be at the meter and regulating stations supplying a particular distribution system. (3) The impact of hydrogen - natural gas blends on state regulatory standards appears to be minimal for PSE and G, but requires further study for various National Codes and for other states.

None

1977-09-01T23:59:59.000Z

330

User manual for AQUASTOR: a computer model for cost analysis of aquifer thermal energy storage coupled with district heating or cooling systems. Volume I. Main text  

DOE Green Energy (OSTI)

A computer model called AQUASTOR was developed for calculating the cost of district heating (cooling) using thermal energy supplied by an aquifer thermal energy storage (ATES) system. The AQUASTOR model can simulate ATES district heating systems using stored hot water or ATES district cooling systems using stored chilled water. AQUASTOR simulates the complete ATES district heating (cooling) system, which consists of two principal parts: the ATES supply system and the district heating (cooling) distribution system. The supply system submodel calculates the life-cycle cost of thermal energy supplied to the distribution system by simulating the technical design and cash flows for the exploration, development, and operation of the ATES supply system. The distribution system submodel calculates the life-cycle cost of heat (chill) delivered by the distribution system to the end-users by simulating the technical design and cash flows for the construction and operation of the distribution system. The model combines the technical characteristics of the supply system and the technical characteristics of the distribution system with financial and tax conditions for the entities operating the two systems into one techno-economic model. This provides the flexibility to individually or collectively evaluate the impact of different economic and technical parameters, assumptions, and uncertainties on the cost of providing district heating (cooling) with an ATES system. This volume contains the main text, including introduction, program description, input data instruction, a description of the output, and Appendix H, which contains the indices for supply input parameters, distribution input parameters, and AQUASTOR subroutines.

Huber, H.D.; Brown, D.R.; Reilly, R.W.

1982-04-01T23:59:59.000Z

331

Comparative ranking of 0. 1-10 MW/sub e/ solar thermal electric power systems. Volume II. Supporting data. Final report  

DOE Green Energy (OSTI)

This report is part of a two-volume set summarizing the results of a comparative ranking of generic solar thermal concepts designed specifically for electric power generation. The original objective of the study was to project the mid-1990 cost and performance of selected generic solar thermal electric power systems for utility applications and to rank these systems by criteria that reflect their future commercial acceptance. This study considered plants with rated capacities of 1-10 MW/sub e/, operating over a range of capacity factors from the no-storage case to 0.7 and above. Later, the study was extended to include systems with capacities from 0.1 to 1 MW/sub e/, a range that is attractive to industrial and other nonutility applications. Volume I summarizes the results for the full range of capacities from 0.1 to 1.0 MW/sub e/. Volume II presents data on the performance and cost and ranking methodology.

Thornton, J.P.; Brown, K.C.; Finegold, J.G.; Gresham, J.B.; Herlevich, F.A.; Kriz, T.A.

1980-07-01T23:59:59.000Z

332

An R&D Project Management and Selection System for the Utilization Technology Branch, Division of Geothermal Energy, Volume III - Project Selection Procedure and Benefit/Cost Analysis  

DOE Green Energy (OSTI)

This report in three volumes describes an R and D project management and selection system developed for the Utilization Technology Branch of the Division of Geothermal Energy, Department of Energy. The proposed project management system (PMS) consists of a project data system (PDS) and a project selection procedure (PSP). The project data system consists of a series of project data forms and project status logs, and descriptions of information pathways. The PDS emphasizes timely monitoring of the technical and financial progress of projects, maintenance of the history of the project and rapid access to project information to facilitate responsive reporting to DGE and DOE Upper Management. The project selection procedure emphasizes a R and D product-oriented approach to benefit/cost analysis of individual projects. The report includes: (a) a description of the system, and recommendations for its implementation, (b) the PDS forms and explanation of their use, (c) a glossary of terms for use on the forms, (d) a description of the benefit/cost approach, (e) a data base for estimating R and D benefits, and (f) examples of test applications of the system to nine current DGE projects. This volume describes a proposed procedure for R and D project selection. The benefit/cost analysis part of the procedure estimates financial savings expected to result from the commercial use of hardware or process products of R and D. Savings are estimated with respect to the geothermal power plants expected to come on line between 1978 and 2000.

Dhillon, Harpal S.; Entingh, Daniel J.

1978-05-01T23:59:59.000Z

333

SOLERAS - Solar Energy Water Desalination Project: Chicago Bridge and Iron Company. System design final report, Volume 2. Appendix  

Science Conference Proceedings (OSTI)

Volume II of CBI's final report of work under Phase 1 of the desalination project, submitted in August 1981, is an appendix containing detailed equipment specifications and descriptions of all major subsystems of the proposed pilot desalination plant. Piping and instrumentation drawings, electrical power distribution diagrams, and building floor plans are also provided. The appendix includes technical specifications for all pumps, storage tanks, heat exchangers, the turbine and diesel generators, oil heater, melter assembly and counterwasher.

Not Available

1986-01-01T23:59:59.000Z

334

User manual for AQUASTOR: a computer model for cost analysis of aquifer thermal-energy storage oupled with district-heating or cooling systems. Volume II. Appendices  

DOE Green Energy (OSTI)

A computer model called AQUASTOR was developed for calculating the cost of district heating (cooling) using thermal energy supplied by an aquifer thermal energy storage (ATES) system. the AQUASTOR Model can simulate ATES district heating systems using stored hot water or ATES district cooling systems using stored chilled water. AQUASTOR simulates the complete ATES district heating (cooling) system, which consists of two prinicpal parts: the ATES supply system and the district heating (cooling) distribution system. The supply system submodel calculates the life-cycle cost of thermal energy supplied to the distribution system by simulating the technical design and cash flows for the exploration, development, and operation of the ATES supply system. The distribution system submodel calculates the life-cycle cost of heat (chill) delivered by the distribution system to the end-users by simulating the technical design and cash flows for the construction and operation of the distribution system. The model combines the technical characteristics of the supply system and the technical characteristics of the distribution system with financial and tax conditions for the entities operating the two systems into one techno-economic model. This provides the flexibility to individually or collectively evaluate the impact of different economic and technical parameters, assumptions, and uncertainties on the cost of providing district heating (cooling) with an ATES system. This volume contains all the appendices, including supply and distribution system cost equations and models, descriptions of predefined residential districts, key equations for the cooling degree-hour methodology, a listing of the sample case output, and appendix H, which contains the indices for supply input parameters, distribution input parameters, and AQUASTOR subroutines.

Huber, H.D.; Brown, D.R.; Reilly, R.W.

1982-04-01T23:59:59.000Z

335

Volume State  

Gasoline and Diesel Fuel Update (EIA)

22 22 Volume State State or Country From/To Receipts/ Imports From Deliveries/ Exports To Net a Alabama Florida .................................................................. 0 722,558 -722,558 Georgia................................................................. 0 1,352,308 -1,352,308 Gulf of Mexico....................................................... 123,132 0 123,132 Mississippi ............................................................ 2,758,595 0 2,758,595 Tennessee............................................................ 1,744 764,749 -763,005 Total..................................................................... 2,883,471 2,839,615 43,856

336

Utility FGD Survey, January--December 1989. Volume 2, Design performance data for operating FGD systems, Part 1  

Science Conference Proceedings (OSTI)

The Utility flue gas desulfurization (FGD) Survey report, which is generated by a computerized data base management system, represents a survey of operational and planned domestic utility flue gas desulfurization (FGD) systems. It summarizes information contributed by the utility industry, system and equipment suppliers, system designers, research organizations, and regulatory agencies. The data cover system design, fuel characteristics, operating history, and actual system performance. Also included is a unit-by-unit discussion of problems and solutions associated with the boilers, scrubbers, and FGD systems. The development status (operational, under construction, or in the planning stages), system supplier, process, waste disposal practice, and regulatory class are tabulated alphabetically by utility company.

Hance, S.L.; McKibben, R.S.; Jones, F.M. [IT Corp., Cincinnati, OH (United States)

1992-03-01T23:59:59.000Z

337

Final safety evaluation report related to the certification of the System 80{sup +} design (Docket No. 52-002). Volume 1, Chapters 1--14  

Science Conference Proceedings (OSTI)

This final safety evaluation report (FSER) documents the technical review of the System 80+ standard design by the US Nuclear Regulatory Commission (NRC) staff. The application for the System 80+ design was submitted by Combustion Engineering, Inc., now Asea Brown Boveri-Combustion Engineering (ABB-CE) as an application for design approval and subsequent design certification pursuant to 10 CFR {section} 52.45. System 80+ is a pressurized water reactor with a rated power of 3914 megawatts thermal (MWt) and a design power of 3992 MWt at which accidents are analyzed. Many features of the System 80+ are similar to those of Abb-CE`s System 80 design from which it evolved. Unique features of the System 80+ design included: a large spherical, steel containment; an in-containment refueling water storage tank; a reactor cavity flooding system, hydrogen ignitors, and a safety depressurization system for severe accident mitigation; a combustion gas turbine for an alternate ac source; and an advanced digitally based control room. On the basis of its evaluation and independent analyses, the NRC staff concludes that ABB-CE`s application for design certification meets the requirements of Subpart B of 10 CFR Part 52 that are applicable and technically relevant to the System 80+ standard design. This document, Volume 1, contains Chapters 1 through 14 of this report.

Not Available

1994-08-01T23:59:59.000Z

338

Final safety evaluation report related to the certification of the System 80{sup +} design (Docket No. 52-002). Volume 2, Chapters 15--22 and appendices  

SciTech Connect

This final safety evaluation report (FSER) documents the technical review of the System 80+ standard design by the US Nuclear Regulatory Commission (NRC) staff. The application for the system 80+ design was submitted by Combustion Engineering, Inc., now Asea Brown Boveri-Combustion Engineering (ABB-CE) as an application for design approval and subsequent design certification pursuant to 10 CFR {section} 52.45. System 80+ is a pressurized water reactor with a rated power of 3914 megawatts thermal (MWt) and a design power of 3992 MWt at which accidents are analyzed. Many features of the System 80+ are similar to those of ABB-CE`s System 80 design from which it evolved. Unique features of the System 80+ design include: a large spherical, steel containment; an in-containment refueling water storage tank; a reactor cavity flooding system, hydrogen ignitors and a safety depressurization system for severe accident mitigation; a combustion gas turbine for an alternate ac source; and an advanced digitally based control room. On the basis of its evaluation and independent analyses, the NRC staff concludes that ABB-CE`s application for design certification meets the requirements of Subpart B of 10 CFR Part 52 that are applicable and technically relevant to the System 80+ standard design. This document, Volume 2, contains Chapters 15 through 22 and Appendices A through E.

Not Available

1994-08-01T23:59:59.000Z

339

Ocean thermal energy conversion power system development: I. Preliminary design report. Phase I. Volume 5. Appendixes H, I, J, and K. Final report  

DOE Green Energy (OSTI)

The conceptual design of a 40 to 50 MW closed cycle ammonia OTEC commercial plant, the preliminary design of a 10 MW OTEC module analogous to the 50 MW module, and the preliminary design of heat exchanger test articles (evaporator and condenser) representative of the 50 MW heat exchangers for testing in OTEC-1 are presented. This volume of the report includes the following appendices: H) conceptual design description of the electrical systems; I) control and instrumentation; J) OTEC power module assembly; and K) cost estimates for each of the cost components. (WHK)

Not Available

1978-12-18T23:59:59.000Z

340

Study of photovoltaic cost elements. Volume 4. Installation cost model for residential PV systems: users manual. Final report  

SciTech Connect

A quantitative methodology is presented for estimating installation costs of residential photovoltaic systems. The Installation Cost Model for Residential PV Systems is comprised of 144 estimating equations selectively exercised, based on user definition of the system. At the input stage, Residential PV systems can be fully described by 9 design option categories and 9 system specification categories. All assumptions have been validated with installers of solar thermal systems and with TB and A's Architects and Engineers Division. A discussion of the model is included as well as an example of its use with an 8 KW PV system for a Southwest All-Electric Residential design.

1981-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

User Instructions for the Systems Assessment Capability, Rev. 1, Computer Codes Volume 1: Inventory, Release, and Transport Modules  

SciTech Connect

This document contains detailed user instructions for the transport codes for Rev. 1 of the System Assessment Capability.

Eslinger, Paul W.; Miley, Terri B.; Engel, David W.; Nichols, William E.; Gerhardstein, Lawrence H.; Strenge, Dennis L.; Lopresti, Charles A.; Wurstner, Signe K.

2004-09-12T23:59:59.000Z

342

Condition Assessment Survey (CAS) Program. Deficiency standards and inspections methods manual: Volume 11, 0.11 Specialty systems  

SciTech Connect

General information is presented for asset determinant factor/CAS repair codes/CAS cost factors; guide sheet tool & material listing; testing methods; inspection frequency; standard system design life tables; system work breakdown structure; and general system/material data. Deficiency standards and inspection methods are presented for canopies; loading dock systems; tanks; domes (bulk storage, metal framing); louvers & vents; access floors; integrated ceilings; and mezzanine structures.

Not Available

1993-05-01T23:59:59.000Z

343

Sperry Low Temperature Geothermal Conversion System, Phase I and Phase II. Volume IV. Field activities. Final report  

DOE Green Energy (OSTI)

This volume describes those activities which took place at the Sperry DOE Gravity Head plant site at the East Mesa Geothermal Reservoir near Holtville, California between February 1980, when site preparation was begun, and November 1982, when production well 87-6 was permanently abandoned. Construction activities were terminated in July 1981 following the liner collapse in well 87-6. Large amounts of program time manpower, materials, and funds had been diverted in a nine-month struggle to salvage the production well. Once these efforts proved futile, there was no rationale for continuing with the site work unless and until sufficient funding to duplicate well 87-6 was obtained. Activities reported here include: plant construction and pre-operational calibration and testing, drilling and completion of well 87-6, final repair effort on well 87-6, abandonment of well 87-6, and performance evaluation of well 87.6. (MHR)

Harvey, C.

1984-01-01T23:59:59.000Z

344

State Volume  

Gasoline and Diesel Fuel Update (EIA)

Volume of Natural Gas Delivered to Processing Plants (million cubic feet) Total Liquids Extracted (thousand barrels) Extraction Loss Located Within the State Located Outside of the State Total Processed Volume (million cubic feet Estimated Heat Content (billion Btu) Alabama...................... 111,656 2,614 114,270 4,476 5,810 18,610 Alaska ......................... 2,987,364 0 2,987,364 33,346 38,453 148,444 Arkansas..................... 214,868 161 215,029 237 474 977 California..................... 240,566 0 240,566 9,798 12,169 41,037 Colorado ..................... 493,748 1,249 494,997 16,891 23,420 63,411 Florida......................... 5,900 0 5,900 1,130 1,143 4,202 Illinois.......................... 578 0 578 63 64 271 Kansas........................ 825,825 2,731 828,556 30,617 41,115 120,221 Kentucky .....................

345

Intermediate photovoltaic system application experiment operational performance report. Volume 3. For G. N. Wilcox Memorial Hospital, Kauai, Hawaii  

DOE Green Energy (OSTI)

Presented are the project description, list of participants, and system specifications for the intermediate photovoltaic project at G.N. Wilcox Memorial Hospital, Kauai, Hawaii.

Not Available

1982-09-01T23:59:59.000Z

346

Full-System Decontamination of a BWR Using the LOMI Process Volume 5: Shielding and Radiation Protection  

Science Conference Proceedings (OSTI)

The LOMI (low-oxidation-state metal-ion) dilute-chemical-decontamination process has been qualified for use on the complete reactor system of BWRs. Full-system decontamination offers several economic and operational advantages over current partsystem applications. This study provides the technical basis for a safety evaluation.

1991-10-30T23:59:59.000Z

347

SOLERAS - Solar Controlled Environment Agriculture Project. Final report, Volume 4. Saudi Engineering Solar Energy Applications System Design Study  

DOE Green Energy (OSTI)

Literature summarizing a study on the Saudi Arabian solar controlled environment agriculture system is presented. Specifications and performance requirements for the system components are revealed. Detailed performance and cost analyses are used to determine the optimum design. A preliminary design of an engineering field test is included. Some weather data are provided for Riyadh, Saudi Arabia. (BCS)

Not Available

1985-01-01T23:59:59.000Z

348

Design and Testing of a Landfill Gas Cleanup System for Carbonate Fuel Cell Power Plants: Volume 1: Field Test Results  

Science Conference Proceedings (OSTI)

This report presents results of an effort to develop a low-cost cleanup system that would enable landfill gas to be used in carbonate fuel cells or other power generation devices. The EPRI-developed system is now available for license to commercial applications.

1997-11-26T23:59:59.000Z

349

Analysis of concentrating PV-T systems for the commercial/industrial sector. Volume III. Technical issues and design guidance  

DOE Green Energy (OSTI)

This report provide appropriate guidance for addressing the major technical issues associated with the design and installation of a photovoltaic-thermal (PV-T) system. Nomographs are presented for developing preliminary sizing and costing, and issues associated with specific components and the overall design of the electrical and mechanical system are discussed. SAND82-7157/2 presents a review of current PV-T technology and operating systems and a study of potential PV-T applications. Detailed PV-T system designs for three selected applications and the results of a trade-off study for these applications are presented in SAND82-7157/4. A summary of the major results of this entire study and conclusions concerning PV-T systems and applications is presented in SAND82-7157/1.

Schwinkendorf, W.E.

1984-09-01T23:59:59.000Z

350

Oxygen enriched combustion system performance study: Volume 3, Burner tests and combustion modeling: Final report, Phase 1  

SciTech Connect

Oxygen enriched combustion (OEC) has been shown to have significant energy savings potential in industrial furnace applications. High temperature industrial furnaces, such as glass melting furnaces, appear to be the most promising applications for oxygen enriched combustion. In these applications, the principal energy savings result from minimizing the fuel energy required to heat the diluent nitrogen in air. The results of technical and economic assessment of OEC and market assessment were reported in Volume 1 and 2 of the current study. This report describes the results of burner evaluation tests over a range of oxygen enrichment and a numerical simulation study. The first part refers to the experimental results of both conventional air-fired burners and specially designed oxygen-fuel burners, evaluated at two scales. Part 2 of this report is concerned with the application of a computer code to extrapolate the results from small scale combustion tests to industrial furnaces. The experiments were designed as a comparative evaluation to: determine the operating range of different burner designs with oxygen enrichment; measure detailed flame characteristics for both air and enriched oxygen conditions; and estimate expected performance from research furnace results to actual industrial applications. 14 refs., 76 figs., 20 tabs.

Kwan, Y.; Abele, A.R.; Richter, W.; Chen, S.L.; Payne, R.; Kobayashi, H.; Silver, S.L.

1988-09-01T23:59:59.000Z

351

Solar Central Receiver Hybrid Power Systems sodium-cooled receiver concept. Final report. Volume II, Book 1. Conceptual design, Sections 1 through 4  

DOE Green Energy (OSTI)

The overall, long-term objective of the Solar Central Receiver Hybrid Power System program is to identify, characterize, and ultimately demonstrate the viability and cost effectiveness of solar/fossil, steam Rankine cycle, hybrid power systems that: (1) consist of a combined solar central receiver energy source and a nonsolar energy source at a single, common site, (2) may operate in the base, intermediate, and peaking capacity modes, (3) produce the rated output independent of variations in solar insolation, (4) provide a significant savings (50% or more) in fuel consumption, and (5) produce power at the minimum possible cost in mills/kWh. It is essential that these hybrid concepts be technically feasible and economically competitive with other systems in the near to mid-term time period (1985-1990) on a commercial scale. The program objective for Phase I is to identify and conceptually characterize solar/fossil steam Rankine cycle, commercial-scale, power plant systems that are economically viable and technically feasible. This volume presents in detail the market analysis, parametric analysis, and the selection process for the preferred system. (WHK)

None

1980-01-01T23:59:59.000Z

352

Solar Central Receiver Hybrid Power Systems sodium-cooled receiver concept. Final report. Volume II, Book 2. Conceptual design, Sections 5 and 6  

DOE Green Energy (OSTI)

The overall, long-term objective of the Solar Central Receiver Hybrid Power System program is to identify, characterize, and ultimately demonstrate the viability and cost effectiveness of solar/fossil, steam Rankine cycle, hybrid power systems that: (1) consist of a combined solar central receiver energy source and a nonsolar energy source at a single, common site, (2) may operate in the base, intermediate, and peaking capacity modes, (3) produce the rated output independent of variations in solar insolation, (4) provide a significant savings (50% or more) in fuel consumption, and (5) produce power at the minimum possible cost in mills/kWh. It is essential that these hybrid concepts be technically feasible and economically competitive with other systems in the near to mid-term time period (1985-1990) on a commercial scale. The program objective for Phase I is to identify and conceptually characterize solar/fossil steam Rankine cycle, commercial-scale, power plant systems that are economically viable and technically feasible. This volume contains the detailed conceptual design and cost/performance estimates and an assessment of the commercial scale solar central receiver hybrid power system. (WHK)

None

1980-01-01T23:59:59.000Z

353

Ocean thermal energy conversion power system development-I. Preliminary design report. Volume 3. Appendixes D, E, and F. Phase I. Final report  

DOE Green Energy (OSTI)

The conceptual design of a 40 to 50 MW closed cycle ammonia OTEC commercial plant, the preliminary design of a 10 MW OTEC module analogous to the 50 MW module, and the preliminary design of heat exchanger test articles (evaporator and condenser) representative of the 50 MW heat exchangers for testing in OTEC-1 are presented. This volume includes the appendices: D) system equipment (hardware breakdown structure; 10-MW hardware listing; list of support and maintenance equipment, tools and spare parts; sacrificial anodes; M.A.N. brush; and Alclad 3004 data); E) heat exchanger supporting data (analyses/configuration, contract tooling, manufacturing plan, specification, and evaporator ammonia liquid distribution system); and F) rotating machinery (performance characteristics, radial inflow turbine; item descriptions; weight calculation-rotor; producibility analysis; long lead-time items; spares; support equipment; non recurring costs; performance characteristics-axial flow turbine; Worthington pump data; and American M.A.N. Corporation data). Also included is attachment 1 to the phase I final report which presents details of the system modeling; design, materials considerations, and systems analysis of the baseline module; system cost analysis; and supporting data. (WHK)

Not Available

1978-12-18T23:59:59.000Z

354

Artificial heart development program. Volume I. System development. Phase III summary report, July 1, 1973--September 30, 1977  

SciTech Connect

Efforts and results in the development of the power system portions of a calf implantable model of nuclear-powered artificial heart are discussed. The primary objective in developing the implantable model was to solve the packaging problems for total system implantation. The power system's portion is physically that portion of the implantable model between the /sup 238/Pu heat sources and the blood pump ventricles. The /sup 238/Pu heat sources and blood pump ventricles were provided as Government Furnished Equipment as developed and fabricated by other contractors.

1977-01-01T23:59:59.000Z

355

Lean manufacturing system design and value stream management in a high-mix, low-volume environment  

E-Print Network (OSTI)

Value Stream Mapping is a powerful tool for identifying sources of waste and for creating the vision for the future state of a production system. As a management tool, however, it lacks in specific focus of roles, ...

Gates, Matthew David, 1973-

2004-01-01T23:59:59.000Z

356

Oxygen enriched combustion system performance study: Phase 1, Interim/final report: Volume 1, Technical and economic analysis  

Science Conference Proceedings (OSTI)

Technical and economic feasibility of using oxygen enriched combustion (OEC) and preheated oxygen enriched combustion (POEC) for industrial furnace applications was evaluated. The potential for fuel savings and productivity improvements with OEC/POEC systems was parametrically analyzed for a broad range of furnace conditions including those for steel heating, glass melting and aluminum melting. The changes in combustion characteristics with OEC were reviewed and their effects on furnace applications discussed. Relative advantages of different enrichment techniques, safety considerations and the effects of OEC on combustion-generated pollutants were also evaluated. The characteristics and economics of the state-of-the-art oxygen generation methods including PSA, membrane and cryogenic systems were evaluated to identify cost effective methods of supplying oxygen enriched air. The potential synergistic effects of combining preheating and oxygen enrichment were investigated by analyzing fuel savings and the capital and operating costs. The overall process economics of conventional heat recovery systems, and various OEC/POEC systems were compared.

Kobayashi, Hisashi

1987-03-01T23:59:59.000Z

357

Guidelines for Induced Flue Gas Recirculation: Volume 1: Reducing Air/Gas System Resistance and Enhancing Fan Capacity  

Science Conference Proceedings (OSTI)

This document guides users through a logical sequence, or "road map," of activities and decisions for optimizing solutions for fans, ducts, and related equipment in fossil plant combustion air and gas systems.

1999-12-13T23:59:59.000Z

358

Clouds and the Earth''s Radiant Energy System (CERES) Algorithm Theoretical Basis Document. Volume I-Overviews (Subsystem 0)  

Science Conference Proceedings (OSTI)

The theoretical bases for the Release 1 algorithms that will be used to process satellite data for investigation of the Clouds and the Earth''s Radiant Energy System (CERES) are described. The architecture for software implementation of the methodologies ...

Team CERES Science

1995-12-01T23:59:59.000Z

359

Intelligent Mobile Sensor System for drum inspection and monitoring -- Volume 2. Final report, October 1, 1993--April 22, 1995  

Science Conference Proceedings (OSTI)

The objective of the Intelligent Mobile Sensor System (IMSS) project was to develop an operational system for monitoring and inspection activities for waste storage facility operations at several DOE sites. Specifically, the product of this effort was a robotic device with enhanced intelligence and maneuverability capable of conducting routine inspection of stored waste drums. The system has an integrated sensor suite for problem-drum detection, and creates and maintains a site database both for inspection planning and for data correlation, updating, and report generation. The system is capable of departing on an assigned mission, collecting required data, recording which portions of its mission had to be aborted or modified due to environmental constraints, and reporting back when the mission is complete. Successful identification of more than 96% of drum defects has been demonstrated in a high fidelity waste storage facility mockup. Identified anomalies included rust spots, rust streaks, areas of corrosion, dents, and tilted drums. All drums were positively identified and correlated with the site database. This development effort was separated into three phases of which phase three is now complete. The first phase demonstrated an integrated system (maturity level IVa) for monitoring and inspection activities for waste storage facility operations. The second phase demonstrated a prototype system appropriate for operational use in an actual storage facility. The prototype employed an integrated design that considered operational requirements, hardware costs, maintenance, safety, and robustness. The final phase has demonstrated the commercial viability of the vehicle in operating waste storage facilities at Fernald, Ohio and the Idaho National Engineering Laboratory (INEL). This report summarizes the system upgrades performed in phase 3 and the evaluation of the IMSS Phase 3 system and vehicle.

NONE

1995-12-31T23:59:59.000Z

360

Tokamak Physics EXperiment (TPX): Toroidal field magnet design, development and manufacture. SDRL 15, System design description. Volume 1  

Science Conference Proceedings (OSTI)

This System Design Description, prepared in accordance with the TPX Project Management Plan provides a summary or TF Magnet System design features at the conclusion of Phase I, Preliminary Design and Manufacturing Research. The document includes the analytical and experimental bases for the design, and plans for implementation in final design, manufacturing, test, and magnet integration into the tokamak. Requirements for operation and maintenance are outlined, and references to sources of additional information are provided.

NONE

1995-09-22T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Solar energy conversion systems engineering and economic analysis radiative energy input/thermal electric output computation. Volume III  

DOE Green Energy (OSTI)

The direct energy flux analytical model, an analysis of the results, and a brief description of a non-steady state model of a thermal solar energy conversion system implemented on a code, SIRR2, as well as the coupling of CIRR2 which computes global solar flux on a collector and SIRR2 are presented. It is shown how the CIRR2 and, mainly, the SIRR2 codes may be used for a proper design of a solar collector system. (LEW)

Russo, G.

1982-09-01T23:59:59.000Z

362

PATRAM '80. Proceedings. Volume 2  

Science Conference Proceedings (OSTI)

Volume 2 contains papers from the following sessions: Safeguards-Related Problems; Neutronics and Criticality; Operations and Systems Experience II; Plutonium Systems; Intermediate Storage in Casks; Operations and Systems Planning; Institutional Issues; Structural and Thermal Evaluation I; Poster Session B; Extended Testing I; Structural and Thermal Evaluation II; Extended Testing II; and Emergency Preparedness and Response. Individual papers were processed. (LM)

Huebner, H.W. (ed.)

1980-01-01T23:59:59.000Z

363

PATRAM '80. Proceedings. Volume 1  

Science Conference Proceedings (OSTI)

Volume 1 contains papers from the following sessions: Plenary Session; Regulations, Licensing and Standards; LMFBR Systems Concepts; Risk/Safety Assessment I; Systems and Package Design; US Institutional Issues; Risk/Safety Assessment II; Leakage, Leak Rate and Seals; Poster Session A; Operations and Systems Experience I; Manufacturing Processes and Materials; and Quality Assurance and Maintenance. Individual papers were processed. (LM)

Huebner, H.W. (ed.)

1980-01-01T23:59:59.000Z

364

Test procedures and protocols: Their relevance to the figure of merit for thermal distribution systems. Volume 1: Informal report  

Science Conference Proceedings (OSTI)

A conceptual framework is developed that categorizes measurement protocols for forced-air thermal distribution systems in small buildings. This framework is based on the distinction between two generic approaches. The {open_quote}system-comparison{close_quote} approach seeks to determine, via a pair of whole-house energy-use measurements, the difference in energy use between the house with the as-found duct system and the same house with no energy losses attributable to the thermal distribution system. The {open_quote}component loss-factor{close_quote} approach identifies and measures the individual causes of duct losses, and then builds up a value for the net overall duct efficiency, usually with the help of computer simulation. Examples of each approach are analyzed and related to a proposed Figure of Merit for thermal distribution systems. This Figure of Merit would serve as the basis for a Standard Method of Test analogous to those already in place for furnaces, boilers, air conditioners, and heat pumps.

Andrews, J.W.

1993-09-01T23:59:59.000Z

365

Sperry Low Temperature Geothermal Conversion System, Phase I and Phase II. Volume V. Component development. Final report  

DOE Green Energy (OSTI)

The fundamental inventions which motivate this program are system concepts centered on a novel heat engine cycle and the use of downwell heat exchange. Here, the primary emphasis is on downwell hardware. The only surface equipment included is the surface portion of the instrumentation and control systems. Downwell instrumentation is reported. Downwell conduits and techniques for installing, connecting and sealing them are covered. The downwell turbine-pump unit (TPU) is a critical component since it is relatively inaccessible and operates in a hostile environment. Its development is reported. The TPU for the gravity-head system requires a different type of turbine because of the large flow-rate through it and the small pressure difference across it. The design study for a Francis turbine to meet these requirements is reported. A feature of these systems is use of a downwell heat exchanger. There were extensive studies of tube-bundle configuration, tube-sheet seals, structural integrity, and flow and heat transfer, as well as the research on welded connections and sliding elastomeric seals. Another innovative component in these systems is the enthalpy recovery unit (ERU). This direct-contact heat exchanger compensates for under-cooling in the condenser and superheat in the main turbine exhaust.

Harvey, C.; McBee, W.; Matthews, H.B.

1984-01-01T23:59:59.000Z

366

Assessment of solar options for small power systems applications. Volume II. Identification and characterization of concepts for analysis  

DOE Green Energy (OSTI)

The primary purpose of this study is to provide DOE with an independent, objective assessment of the principal solar thermal conversion concepts that have the potential for achieving commercial success as small electric power sytems in the 1- to 10-MWe range. Seven generic types of collectors, together with associated subsystems for electric power generation, were considered in this study. The collectors can be classified into three categories: (1) two-axis tracking (with compound curvature reflecting surfaces); (2) one-axis tracking (with single-curvature reflecting surfaces); and (3) nontracking (with low-concentration reflecting surfaces). These collectors can be combined with energy transport, energy storage, and power conversion subsystems in a wide variety of ways to formulate conceptual systems for electric power generation. In this study, attention was restricted to configurations that are potentially suitable for development as small power systems (1 to 10 MWe) in the long term (1990 to 2000), with initial commercialization by the mid-1980s. Cogeneration and total energy systems were beyond the scope of this study. All seven types of collectors were analyzed in conceptual system configurations with Rankine-cycle engines. Because they can operate at particularly high concentration ratios, two of the collectors (the Point Focus Central Receiver and the Point Focus Distributed Receiver) were also analyzed with Brayton-cycle engines. In addition, the latter of the two was analyzed with Stirling-cycle engines. With these engine options, 10 conceptual systems were formulated for analysis. Results are presented in detail. (WHK)

Laity, W.W.; Aase, D.T.; Apley, W.J.; Bird, S.P.; Drost, M.K.; Williams, T.A.

1980-06-01T23:59:59.000Z

367

Fort Hood Solar Total Energy Project. Volume II. Preliminary design. Part 2. System performance and supporting studies. Final report  

DOE Green Energy (OSTI)

The preliminary design developed for the Solar Total Energy System to be installed at Fort Hood, Texas, is presented. System performance analysis and evaluation are described. Feedback of completed performance analyses on current system design and operating philosophy is discussed. The basic computer simulation techniques and assumptions are described and the resulting energy displacement analysis is presented. Supporting technical studies are presented. These include health and safety and reliability assessments; solar collector component evaluation; weather analysis; and a review of selected trade studies which address significant design alternatives. Additional supporting studies which are generally specific to the installation site are reported. These include solar availability analysis; energy load measurements; environmental impact assessment; life cycle cost and economic analysis; heat transfer fluid testing; meteorological/solar station planning; and information dissemination. (WHK)

None,

1979-01-01T23:59:59.000Z

368

Integrated Safety Management System Phase 1 and 2 Verification for the Environmental Restoration Contractor Volumes 1 and 2  

SciTech Connect

DOE Policy 450.4 mandates that safety be integrated into all aspects of the management and operations of its facilities. The goal of an institutionalized Integrated Safety Management System (ISMS) is to have a single integrated system that includes Environment, Safety, and Health requirements in the work planning and execution processes to ensure the protection of the worker, public, environment, and the federal property over the life cycle of the Environmental Restoration (ER) Project. The purpose of this Environmental Restoration Contractor (ERC) ISMS Phase MI Verification was to determine whether ISMS programs and processes were institutionalized within the ER Project, whether these programs and processes were implemented, and whether the system had promoted the development of a safety conscious work culture.

CARTER, R.P.

2000-04-04T23:59:59.000Z

369

Viability Assessment Volume 4  

SciTech Connect

Volume 4 provides the DOE plan and cost estimate for the remaining work necessary to proceed from completing this VA to submitting an LA to NRC. This work includes preparing an EIS and evaluating the suitability of the site. Both items are necessary components of the documentation required to support a decision in 2001 by the Secretary of Energy on whether or not to recommend that the President approve the site for development as a repository. If the President recommends the site to Congress and the site designation becomes effective, then DOE will submit the LA to NRC in 2002 for authorization to construct the repository. The work described in Volume 4 constitutes the last step in the characterization of the Yucca Mountain site and the design and evaluation of the performance of a repository system in the geologic setting of this site. The plans in this volume for the next 4 years' work are based on the results of the previous 15 years' work, as reported in Volumes 1, 2, and 3 of this VA. Volume 1 summarizes what DOE has learned to date about the Yucca Mountain site. Volume 2 describes the current, reference repository design, several design options that might enhance the performance of the reference design, and several alternative designs that represent substantial departures from the reference design. Volume 2 also summarizes the results of tests of candidate materials for waste packages and for support of the tunnels into which waste would be emplaced. Volume 3 provides the results of the latest performance assessments undertaken to evaluate the performance of the design in the geologic setting of Yucca Mountain. The results described in Volumes 1, 2, and 3 provide the basis for identifying and prioritizing the work described in this volume. DOE believes that the planned work, together with the results of previous work, will be sufficient to support a site suitability evaluation for site recommendation and, if the site is recommended and designated, a defensible LA. Volume 4 is divided into seven sections. Section 2 presents a rationale and summary for the technical work to be done to develop the preclosure and postclosure safety cases that will support the compliance evaluations required for the evaluation of site suitability and for licensing. Section 2 also describes other necessary technical work, including that needed to support design decisions and development of the necessary design information. Section 3 presents a more detailed description of the technical work required to address the issues identified in Section 2. Section 3 also describes activities that will continue after submittal of the site recommendation and the LA. Examples include the drift scale heater test in the Exploratory Studies Facility (Section 3.1.4.3) and long-term waste package corrosion testing (Section 3.2.2.9). Section 4 discusses the statutory and regulatory framework for site recommendation and submittal of an LA, and describes the activities and documentation that must be completed to achieve these milestones, including the development of an EIS. Section 5 describes the numerous activities required to support program milestones, including support for completing the testing program, continuing tests as part of the performance confirmation program, and managing information and records to support regulatory and legal review. Sections 6 and 7 provide cost and schedule information for the activities planned.

DOE

1998-12-01T23:59:59.000Z

370

Viability Assessment Volume 2  

Science Conference Proceedings (OSTI)

This volume describes the major design features of the Monitored Geologic Repository. This document is not intended to provide an exhaustive, detailed description of the repository design. Rather, this document summarizes the major systems and primary elements of the design that are radiologically significant, and references the specific technical documents and design analyses wherein the details can be found. Not all portions of the design are at the same level of completeness. Highest priority has been given to assigning resources to advance the design of the Monitored Geologic Repository features that are important to radiological safety and/or waste isolation and for which there is no NRC licensing precedent. Those features that are important to radiological safety and/or waste isolation, but for which there is an NRC precedent, receive second priority. Systems and features that have no impact on radiological safety or waste isolation receive the lowest priority. This prioritization process, referred to as binning, is discussed in more detail in Section 2.3. Not every subject discussed in this volume is given equal treatment with regard to the level of detail provided. For example, less detail is provided for the surface facility design than for the subsurface and waste package designs. This different level of detail is intentional. Greater detail is provided for those functions, structures, systems, and components that play key roles with regard to protecting radiological health and safety and that are not common to existing nuclear facilities already licensed by NRC. A number of radiological subjects are not addressed in the VA, (e.g., environmental qualification of equipment). Environmental qualification of equipment and other radiological safety considerations will be addressed in the LA. Non-radiological safety considerations such as silica dust control and other occupational safety considerations are considered equally important but are not addressed in th is volume of the VA (see Volume 1, Section 2.2.1.2, subsection on Health Related Mineral Issues).

DOE

1998-12-01T23:59:59.000Z

371

Ocean thermal energy conversion power system development-I. Phase I. Preliminary design report. Volume 1. Final report  

DOE Green Energy (OSTI)

The results of a conceptual and preliminary design study of Ocean Thermal Energy Conversion (OTEC) closed loop ammonia power system modules performed by Lockheed Missiles and Space Company, Inc. (LMSC) are presented. This design study is the second of 3 tasks in Phase I of the Power System Development-I Project. The Task 2 objectives were to develop: 1) conceptual designs for a 40 to 50-MW(e) closed cycle ammonia commercial plant size power module whose heat exchangers are immersed in seawater and whose ancillary equipments are in a shirt sleeve environment; preliminary designs for a modular application power system sized at 10-MW(e) whose design, construction and material selection is analogous to the 50 MW(e) module, except that titanium tubes are to be used in the heat exchangers; and 3) preliminary designs for heat exchanger test articles (evaporator and condenser) representative of the 50-MW(e) heat exchangers using aluminum alloy, suitable for seawater service, for testing on OTEC-1. The reference ocean platform was specified by DOE as a surface vessel with the heat exchanger immersed in seawater to a design depth of 0 to 20 ft measured from the top of the heat exchanger. For the 50-MW(e) module, the OTEC 400-MW(e) Plant Ship, defined in the Platform Configuration and Integration study, was used as the reference platform. System design, performance, and cost are presented. (WHK)

Not Available

1978-12-18T23:59:59.000Z

372

The Design and Implementation of Monitoring System for H2S Gas Volume Fraction with Virtual Instrument  

Science Conference Proceedings (OSTI)

H2S is a kind of poisonous gas that exist in oil, chemical production process. The detection of H2S plays an important role in mine, oil and gas exploration, production of chemical product, control of atmosphere environment. The monitoring system for ...

Wenlian Li; Chuanqing Liu; Yang Li; Fang Xiao

2008-12-01T23:59:59.000Z

373

River Protection Project Integrated safety management system phase II verification report, volumes I and II - 8/19/99  

Science Conference Proceedings (OSTI)

The Department of Energy policy (DOE P 450.4) is that safety is integrated into all aspects of the management and operations of its facilities. In simple and straightforward terms, the Department will ''Do work safely.'' The purpose of this River Protection Project (RPP) Integrated Safety Management System (ISMS) Phase II Verification was to determine whether ISMS programs and processes are implemented within RFP to accomplish the goal of ''Do work safely.'' The goal of an implemented ISMS is to have a single integrated system that includes Environment, Safety, and Health (ES&H) requirements in the work planning and execution processes to ensure the protection of the worker, public, environment, and federal property over the RPP life cycle. The ISMS is comprised of the (1) described functions, components, processes, and interfaces (system map or blueprint) and (2) personnel who are executing those assigned roles and responsibilities to manage and control the ISMS. Therefore, this review evaluated both the ''paper'' and ''people'' aspects of the ISMS to ensure that the system is implemented within RPP. Richland Operations Office (RL) conducted an ISMS Phase I Verification of the TWRS from September 28-October 9, 1998. The resulting verification report recommended that TWRS-RL and the contractor proceed with Phase II of ISMS verification given that the concerns identified from the Phase I verification review are incorporated into the Phase II implementation plan.

SHOOP, D.S.

1999-09-10T23:59:59.000Z

374

Ocean thermal energy conversion gas desorption studies. Volume 1. Design of experiments. [Open-cycle power systems  

Science Conference Proceedings (OSTI)

Seawater deaeration is a process affecting almost all proposed Ocean Thermal Energy Conversion (OTEC) open-cycle power systems. If the noncondensable dissolved air is not removed from a power system, it will accumulate in thecondenser, reduce the effectiveness of condensation, and result in deterioration of system performance. A gas desorption study is being conducted at Oak Ridge National Laboratory (ORNL) with the goal of mitigating these effects; this study is designed to investigate the vacuum deaeration process for low-temperature OTEC conditions where conventional steam stripping deaeration may not be applicable. The first in a series describing the ORNL studies, this report (1) considers the design of experiments and discusses theories of gas desorption, (2) reviews previous relevant studies, (3) describes the design of a gas desorption test loop, and (4) presents the test plan for achieving program objectives. Results of the first series of verification tests and the uncertainties encountered are also discussed. A packed column was employed in these verification tests and test data generally behaved as in previous similar studies. Results expressed as the height of transfer unit (HTU) can be correlated with the liquid flow rate by HTU = 4.93L/sup 0/ /sup 25/. End effects were appreciable for the vacuum deaeration system, and a correlation of them to applied vacuum pressure was derived.

Golshani, A.; Chen, F.C.

1980-10-01T23:59:59.000Z

375

The Coastal Ocean Prediction Systems program: Understanding and managing our coastal ocean. Volume 2: Overview and invited papers  

Science Conference Proceedings (OSTI)

This document is a compilation of summaries of papers presented at the Coastal Ocean Prediction Systems workshop. Topics include; marine forecasting, regulatory agencies and regulations, research and application models, research and operational observing, oceanic and atmospheric data assimilation, and coastal physical processes.

Not Available

1990-05-15T23:59:59.000Z

376

Phase 1: conceptual design. Ocean thermal energy conversion power system development. Volume 2 of 3. Technical details. Final report  

DOE Green Energy (OSTI)

Westinghouse has completed the conceptual design of the Power System for the Ocean Thermal Energy Conversion (OTEC) Demonstration Plant project. This study included the development of a conceptual design for the following three items: first, a full-size power system module for the 100 MWe Demonstration Plant; second, a scaled proof of concept power system; and third, a heat exchanger test article. The study was limited to a closed cycle ammonia power system module, using a water temperature difference of 40/sup 0/F., and a surface platform/ship reference hull. Two power module of 50 MWe each are recommended for the demonstration plant. The 50 MWe module was selected since it has the lowest cost, and since it is of a size which convincingly demonstrates that future economically viable commercial plants, having reliable operation with credible anticipated costs, are possible. A modular, tube bundle approach to heat exchanger design makes large heat exchangers practical and economical. Other power module elements are considered to be within state-of-practice. Technological assessments of all subsystems indicate requirements for verification only, rather than continued research. A complete test program, which will verify the mechanical reliability as well as thermal performance, is recommended.

Not Available

1978-01-30T23:59:59.000Z

377

Methods for dependency estimation and system unavailability evaluation based on failure data statistics. Volume 1, Summary report  

SciTech Connect

This report introduces a new perspective on the basic concept of dependent failures where the definition of dependency is based on clustering in failure times of similar components. This perspective has two significant implications: first, it relaxes the conventional assumption that dependent failures must be simultaneous and result from a severe shock; second, it allows the analyst to use all the failures in a time continuum to estimate the potential for multiple failures in a window of time (e.g., a test interval), therefore arriving at a more accurate value for system unavailability. In addition, the models developed here provide a method for plant-specific analysis of dependency, reflecting the plant-specific maintenance practices that reduce or increase the contribution of dependent failures to system unavailability. The proposed methodology can be used for screening analysis of failure data to estimate the fraction of dependent failures among the failures. In addition, the proposed method can evaluate the impact of the observed dependency on system unavailability and plant risk. The formulations derived in this report have undergone various levels of validations through computer simulation studies and pilot applications. The pilot applications of these methodologies showed that the contribution of dependent failures of diesel generators in one plant was negligible, while in another plant was quite significant. It also showed that in the plant with significant contribution of dependency to Emergency Power System (EPS) unavailability, the contribution changed with time. Similar findings were reported for the Containment Fan Cooler breakers. Drawing such conclusions about system performance would not have been possible with any other reported dependency methodologies.

Azarm, M.A.; Hsu, F.; Martinez-Guridi, G. [Brookhaven National Lab., Upton, NY (US); Vesely, W.E. [Science Applications International Corp., Dublin, OH (US)

1993-07-01T23:59:59.000Z

378

Technical and economic assessment of fluidized-bed-augmented compressed-air energy-storage system. Volume I. Executive summary  

DOE Green Energy (OSTI)

An energy storage system which could be attractive for future electric utility peak-load applications is a modified gas turbine power system utilizing underground storage of very high pressure air. The compressed air energy storage (CAES) concept involves using off-peak electricity generated from indigenous coal or nuclear sources to compress air, storing the air in large underground facilities, and withdrawing the air during peak-load periods when it would be heated by combustion and expanded through gas turbines to generate power. The attractiveness of the CAES concept is based upon its potential to supply competitively priced peaking energy, to reduce peak-load power plant dependence on petroleum-based fuels, and to provide a means for leveling the utility system load demand. Therefore, a technical and economic assessment of coal-fired fluidized bed (FBC) combustor/compressed air energy storage (FBC/CAES) systems was performed and is described. The conclusions drawn from the FBC/CAES study program are encouraging. They indicate that pressurized FBC/CAES power plants should be technologically feasible, provide good performance, and be economically competitive. Specifically, it is concluded that: coal-fired FBC/CAES systems should be technically feasible in the near future and potentially attractive for peak-load power generation; and an open-bed PFBC/CAES configuration would provide the best candidate for early commercialization. It has relatively low risk combined with moderate cost and reasonable round-trip heat rate. It also has the potential for future growth options which tend to reduce costs and lower fuel consumption.

Giramonti, A.J.; Lessard, R.D.; Merrick, D.; Hobson, M.J.

1981-09-01T23:59:59.000Z

379

Intermediate photovoltaic system application experiment operational performance report. Volume 7, for Newman Power Station, El Paso, TX  

DOE Green Energy (OSTI)

Performance data are given for the month of December, 1981 for a photovoltaic power supply at a Texas power station. Data include: monthly and daily electric energy produced; monthly and daily solar energy received; monthly and daily array efficiency; plots of energy produced as a function of power level, voltage, cell temperature, and hour of the day; monthly and daily electrical energy supplied by the photovoltaic system to the load; daily system availability; monthly and hourly insolation; monthly and hourly ambient temperature; monthly and hourly wind speed; wind direction distribution; heating and cooling degree days; number of freeze/thaw cycles; hourly cell temperature; and a plot of daily data acquisition mode and recording interval. Also included are brief summaries of three site events. (LEW)

Not Available

1982-01-01T23:59:59.000Z

380

SOLERAS - Solar Energy Water Desalination Project: Chicago Bridge and Iron Company. Final report: system design extension. Volume 1. Technical report  

Science Conference Proceedings (OSTI)

The design of a solar energy powered, sea water desalination pilot plant for installation at Yanbu, Saudi Arabia, on the shore of the Red Sea is presented. Earlier work is introduced and a description of the system is presented. Important design analyses and cost reduction considerations are reviewed. The pilot plant design is described in detail. Construction plans for and projected operation of the plant are discussed.

Not Available

1985-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Field test of two high-pressure direct-contact downhole steam generators. Volume II. Oxygen/diesel system  

SciTech Connect

A field test of an oxygen/diesel fuel, direct contact steam generator has been completed. The field test, which was a part of Project DEEP STEAM and was sponsored by the US Department of Energy, involved the thermal stimulation of a well pattern in the Tar Zone of the Wilmington Oil Field. The activity was carried out in cooperation with the City of Long Beach and the Long Beach Oil Development Company. The steam generator was operated at ground level, with the steam and combustion products delivered to the reservoir through 2022 feet of calcium-silicate insulated tubing. The objectives of the test included demonstrations of safety, operational ease, reliability and lifetime; investigations of reservoir response, environmental impact, and economics; and comparison of those points with a second generator that used air rather than oxygen. The test was extensively instrumented to provide the required data. Excluding interruptions not attributable to the oxygen/diesel system, steam was injected 78% of the time. System lifetime was limited by the combustor, which required some parts replacement every 2 to 3 weeks. For the conditions of this particular test, the use of trucked-in LOX resulted in liess expense than did the production of the equivalent amount of high pressure air using on site compressors. No statistically significant production change in the eight-acre oxygen system well pattern occurred during the test, nor were any adverse effects on the reservoir character detected. Gas analyses during the field test showed very low levels of SOX (less than or equal to 1 ppM) in the generator gaseous effluent. The SOX and NOX data did not permit any conclusion to be drawn regarding reservoir scrubbing. Appreciable levels of CO (less than or equal to 5%) were measured at the generator, and in this case produced-gas analyses showed evidence of significant gas scrubbing. 64 figures, 10 tables.

Moreno, J.B.

1983-07-01T23:59:59.000Z

382

Central Receiver Solar Thermal Power System, Phase 1: CDRL Item 2, Pilot plant preliminary design report. Volume 1. Executive overview  

SciTech Connect

This summary introduces the McDonnell Douglas Astronautics Company (MDAC) Central Receiver System Preliminary Design and reports the results of the Subsystem Research Experiments (SRE) recently completed. The baseline central receiver concept defined by the MDAC team consists of the following features: (A) An external receiver mounted on a tower, and located in a 360-deg array of sun-tracking heliostats which comprise the collector subsystem. (B) Feedwater from the electrical power generation subsystem is pumped through a riser to the receiver, where the feedwater is converted to superheated steam in a single pass through the tubes of the receiver panels. (C) The steam from the receiver is routed through a downcomer to the ground and introduced to a turbine directly for expansion and generation of electricity, and/or to a thermal storage subsystem, where the steam is condensed in charging heat exchangers to heat a dual-medium oil and rock thermal storage unit (TSU). (D) Extended operation after daylight hours is facilitated by discharging the TSU to generate steam for feeding the admission port of the turbine. (E) Overall control of the system is provided by a master control unit, which handles the interactions between subsystems that take place during startup, shutdown, and transitions between operating modes.

Hallet, Jr., R. W.; Gervais, R. L.

1977-10-01T23:59:59.000Z

383

Technology assessment of solar energy systems. Socioeconomic impacts of solar deployment and conventional energy use. Volume III  

DOE Green Energy (OSTI)

This study presents an analysis of socio-economic impacts of conventional energy prices and solar technology use in the residential sector. Patterns of household energy use are explored as a function of income class. Impacts on household disposable income of use of conventional fuels and technologies as compared to solar alternatives are then assessed. This analysis is conducted for 1978 and 1990 by income class and region. Profiles of residential-solar-system purchases are presented and trends in the adoption of solar systems in this sector are discussed. Because income levels and certain demographic characteristics tend to be correlated, insights regarding the distribution of impacts among population groups can be obtained by examining the demographic composition of US households. Accordingly, socio-economic profiles of the US population are developed to help identify the demographic characteristics of households most severely affected by high energy prices, as well as of those households best able to reduce energy costs through the purchase of solar energy and conservation.

Gordon, J.J.; Tahami, J.E.

1981-08-01T23:59:59.000Z

384

SOLERAS - Solar Energy Water Desalination Project: Chicago Bridge and Iron Company. System design final report. Volume 1. Design report  

Science Conference Proceedings (OSTI)

Chicago Bridge and Iron Company (CBI), based on a demonstrated breakthrough in freeze desalination is proposing an indirect bulk freeze desalination process for seawater that is uniquely integrated with a stand alone solar cogeneration power plant. Working under SOLERAS auspices, CBI and Foster Miller Associates (FMA) have designed an integrated power system consisting of modular parabolic dish point focus solar energy collection, molten salt thermal energy storage, and a conventional steam turbine. The shaft power provides electrical energy needs via a generator and vapor compression energy needs via compressors. The vapor compression and turbine exhaust heat provide the refrigeration required for the unique freeze desalination process. Efficient energy utilization is achieved by using high grade heat to produce compression refrigeration. The flexibility of this system in making use of available energy and certain inherent advantages of the freeze desalination process make it very attractive. The desalination process includes seawater precooling and freezing, ice separation, washing, and melting to produce fresh water. Brine concentrate is rejected back to the sea after heat exchange with feed seawater.

Not Available

1986-01-01T23:59:59.000Z

385

MHD advanced power train. Phase 1, Final report: Volume 3, Power train system description and specification for 200MWe Plant  

DOE Green Energy (OSTI)

This System Design Description and Specification provides the basis for the design of the magnetohydrodynamic (MHD) Power Train (PT) for a nominal 200 MWe early commercial tiHD/Steam Power Plant. This document has been developed under Task 2, Conceptual Design, of Contract DE-AC22-83PC60575 and is to be used by the project as the controlling and coordinating documentation during future design efforts. Modification and revision of this specification will occur as the design matures, and tiie-Westinghouse MHD Project Manager will be the focal point for maintaining this document and issuing periodic revisions. This document is intended to delineate the power train and-power train components requirements and assumptions that properly reflect the MHD/Steam Power Plant in the PT design. The parameters discussed in this document have been established through system calculations as well as through constraints set by technology and by limitations on materials, cost, physical processes associated with MHD, and the expected operating data for the plant. The specifications listed in this document have precedence over all referenced documents. Where this specification appears to conflict with the requirements of a reference document, such conflicts should be brought to the attention of the Westinghouse MHD Project Manager for resolution.

Jones, A.R.

1985-08-01T23:59:59.000Z

386

The design, construction, and monitoring of photovoltaic power system and solar thermal system on the Georgia Institute of Technology Aquatic Center. Volume 1  

DOE Green Energy (OSTI)

This is a report on the feasibility study, design, and construction of a PV and solar thermal system for the Georgia Tech Aquatic Center. The topics of the report include a discussion of site selection and system selection, funding, design alternatives, PV module selection, final design, and project costs. Included are appendices describing the solar thermal system, the SAC entrance canopy PV mockup, and the PV feasibility study.

Long, R.C.

1996-12-31T23:59:59.000Z

387

Final Report: Mobile Surveillance and Wireless Communication Systems Field Operational Test Volume 2: FOT Objectives, Organization, System Design, Results, Conclusions and Recommendations  

E-Print Network (OSTI)

for operation Mobile Surveillance and Wireless CommunicationDesign and Operation The mobile surveillance and wirelessAND WIRELESS COMMUNICATION SYSTEM DESIGN AND OPERATION .

Klein, Lawrence

1999-01-01T23:59:59.000Z

388

Screening study for evaluation of the potential for system 80+ to consume excess plutonium - Volume 2. Final report  

Science Conference Proceedings (OSTI)

As part of the U.S. effort to evaluate technologies offering solutions for the safe disposal or utilization of surplus nuclear materials, the fiscal year 1993 Energy and Water Appropriations legislation provided the Department of Energy (DOE) the necessary funds to conduct multi-phased studies to determine the technical feasibility of using reactor technologies for the triple mission of burning weapons grade plutonium, producing tritium for the existing smaller weapons stockpile, and generating commercial electricity. DOE limited the studies to five advanced reactor designs. Among the technologies selected is the ABB-Combustion Engineering (ABB-CE) System 80+. The DOE study, currently in Phase ID, is proceeding with a more detailed evaluation of the design`s capability for plutonium disposition.

Not Available

1994-04-30T23:59:59.000Z

389

Full-System Decontamination of a BWR Using the LOMI Process Volume 4: Full System Decontamination Experience and Cost-Benefit Analys is  

Science Conference Proceedings (OSTI)

The LOMI (low-oxidation-state metal-ion) dilute-chemical-decontamination process has been qualified for use on the complete reactor system of BWRs. Full-system decontamination offers several economic and operational advantages over current partsystem applications. This study provides the technical basis for a safety evaluation.

1991-10-30T23:59:59.000Z

390

Reduction of NO/sub x/ through staged combustion in combined cycle supplemental boilers. Volume I. Systems optimization analyses. Final report  

SciTech Connect

An investigation directed to control of emissions from supplemental-fired combined cycles with the use of staged combustion in the steam generating portion of the system is discussed. A combined cycle, as considered in this report, is the assembly of any number of gas turbines, steam generators, and steam turbines for electric power generation in which the exhaust of the gas turbines is passed through the steam generators. A supplementary-fired combined cycle employs combustion of fuel in the gas turbine exhaust to increase temperatures in the steam system. Staged combustion is achieved by the separation of the exhaust from the gas turbines into two streams prior to entering the steam generator with provisions for primary combustion of fuel in one stream with a deficiency of air. Combustion is completed in a secondary stage by mixing the unfired stream into the products of the fired stream. The use of staged combustion provides conditions favorable for the occurrence of chemical reactions that result in a reduction of mass flow of nitric oxide (NO) present in the gas turbine exhaust. Volume I is concerned with the engineering analysis of combined cycle performance and NO/sub x/ reduction potential. (GRA)

1975-02-01T23:59:59.000Z

391

Electric and Hybrid Vehicle System Research and Development Project: Hybrid Vehicle Potential Assessment. Volume VIII. Scenario generation  

SciTech Connect

Scenarios are described which have been generated in support of the Hybrid Vehicle Potential Assessment Task under the JPL Electric and Hybrid Vehicle Systems Research and Development Project. The primary function of the scenario generation is to develop a set of consistent and credible forecasts required to estimate the potential impact of hybrid vehicles on future petroleum consumption in the USA, given a set of specific electric, hybrid and conventional vehicle designs. The forecasts are limited to the next 32 years (1978 to 2010. The four major areas of concern are: population and vehicle fleet size; travel patterns and vehicle fleet mix; conventional vehicle technology (Otto baseline); battery technology; and prices. The forecasts have been generated to reflect two baseline scenarios, a Petroleum Conservation Scenario (Scenario A) and an Energy Conservation Scenario (Scenario B). The primary assumption in Scenario A is higher gasoline prices than in Scenario B. This should result in less travel per car and an increased demand for smaller and more fuel efficient cars (compared to Scenario B). In Scenario B the primary assumption is higher prices on cars (new as well as used) than in Scenario A. This should lead to less cars (compared to Scenario A) and a shift to other modes of transportation.

Leschly, K.O.

1979-09-30T23:59:59.000Z

392

Lower Flathead System Fisheries Study, South Bay of Flathead Lake, Volume III, 1983-1987 Final Report.  

DOE Green Energy (OSTI)

The Lower Flathead System Fisheries Study assessed the effects of Kerr Dam operation on the fisheries of the lower Flathead ecosystem. South Bay, the southern most lobe of Flathead Lake, is the most extensive area of shallow water, and therefore, most effected by changes in lake levels. This study began in January of 1984 and was completed in early 1987. Vegetative and structural cover are relatively limited in South Bay, a condition which could contribute to lower recruitment for some fish species. Our data show that the study area contained 0.04% structural and 5.4% vegetative cover in June at full pool. Both figures are less than 1.0% at minimum pool. Structural complexity mediates the ecological interactions between littoral zone fish and their prey, and can affect local productivity and growth in fish. Structural complexity may also be important to overwinter survival of young perch in Flathead Lake. Winter conditions, including ice cover and fall drawdown, seasonally eliminate the vegetative portion of most rooted macrophytes in South Bay. This results in substantial loss of what little structural cover exists, depriving the perch population of habitat which has been occupied all summer. The loss of cover from draw-down concentrates and probably exposes perch to greater predation, including cannibalism, than would occur if structural complexity were greater. 33 refs., 10 figs., 5 tabs.

Cross, David; Waite, Ian

1988-06-01T23:59:59.000Z

393

Automated energy management systems for small buildings. Volume II: market assessment reports, Phase I and II. Final report  

SciTech Connect

Marketec, Inc., as part of a Honeywell research project sponsored by the Department of Energy (DOE), studied the major marketing influences affecting purchasing decisions for a new product concept - an Automated Energy Management System (AEMS). The first part of this study, designated Phase One, deals with four broad assessments of market need for an AEMS within the market segment generally defined as small buildings (75,000 square feet or less). Thus, determinations were made, using carefully selected focus groups, of the following issues: (1) market perception of the market segment in particular; (2) attitudinal statements concerning the solution of these problems; (3) current and projected energy-saving practices by the respondents from the market segment; and (4) an estimate of market potential of an AEMS from an analysis of the focus groups. The second phase of this investigation deals with larger national samplings from the same market segments and uses a questionnaire technique. Three small building sectors were chosen to represent the total small-building market: (1) apartments, (2) schools, and (3) offices. In the aggregate, these three sectors represent 50% or more of the energy consumed, square footage, and number of buildings of that total market.

1978-08-01T23:59:59.000Z

394

Tank Waste Remediation System fiscal year 1996 multi-year program plan WBS 1.1. Revision 1, Volume 1  

Science Conference Proceedings (OSTI)

The 1995 Hanford Mission Plan specifically addresses the tank waste issue and clarifies the link with other initiatives, such as improving management practices and the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan (DOE/RL-91-31). This document captures the results of decision making regarding the application of systems engineering at the Hanford Site, external involvement policy, and site end-state goals. Section 3.5 of the Hanford Mission Plan on Decisions and Directives provides an integrating discussion of the actions of the National Environmental Policy Act (NEPA), and DOE policy, guidance, and decisions associated with binding agreements such as the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement). Two significant components of the Hanford Mission Plan 1994 planning basis are (1) the decisions regarding the disposition of onsite material inventory, and the key programs and interfaces to accomplish this; and (2) the Program Interface Issues section, which identified issues that stretch across program boundaries.

NONE

1995-09-01T23:59:59.000Z

395

Field test of two high-pressure, direct-contact downhole steam generators. Volume I. Air/diesel system  

SciTech Connect

As a part of the Project DEEP STEAM to develop technology to more efficiently utilize steam for the recovery of heavy oil from deep reservoirs, a field test of a downhole steam generator (DSG) was performed. The DSG burned No. 2 diesel fuel in air and was a direct-contact, high pressure device which mixed the steam with the combustion products and injected the resulting mixture directly into the oil reservoir. The objectives of the test program included demonstration of long-term operation of a DSG, development of operational methods, assessment of the effects of the steam/combustion gases on the reservoir and comparison of this air/diesel DSG with an adjacent oxygen/diesel direct contact generator. Downhole operation of the air/diesel DSG was started in June 1981 and was terminated in late February 1982. During this period two units were placed downhole with the first operating for about 20 days. It was removed, the support systems were slightly modified, and the second one was operated for 106 days. During this latter interval the generator operated for 70% of the time with surface air compressor problems the primary source of the down time. Thermal contact, as evidenced by a temperature increase in the production well casing gases, and an oil production increase were measured in one of the four wells in the air/diesel pattern. Reservoir scrubbing of carbon monoxide was observed, but no conclusive data on scrubbing of SO/sub x/ and NO/sub x/ were obtained. Corrosion of the DSG combustor walls and some other parts of the downhole package were noted. Metallurgical studies have been completed and recommendations made for other materials that are expected to better withstand the downhole combustion environment. 39 figures, 8 tables.

Marshall, B.W.

1983-05-01T23:59:59.000Z

396

SCANS (Shipping Cask ANalysis System) a microcomputer-based analysis system for shipping cask design review: User`s manual to Version 3a. Volume 1, Revision 2  

SciTech Connect

SCANS (Shipping Cask ANalysis System) is a microcomputer-based system of computer programs and databases developed at the Lawrence Livermore National Laboratory (LLNL) for evaluating safety analysis reports on spent fuel shipping casks. SCANS is an easy-to-use system that calculates the global response to impact loads, pressure loads and thermal conditions, providing reviewers with an independent check on analyses submitted by licensees. SCANS is based on microcomputers compatible with the IBM-PC family of computers. The system is composed of a series of menus, input programs, cask analysis programs, and output display programs. All data is entered through fill-in-the-blank input screens that contain descriptive data requests. Analysis options are based on regulatory cases described in the Code of Federal Regulations 10 CFR 71 and Regulatory Guides published by the US Nuclear Regulatory Commission in 1977 and 1978.

Mok, G.C.; Thomas, G.R.; Gerhard, M.A.; Trummer, D.J.; Johnson, G.L. [Lawrence Livermore National Lab., CA (United States)

1998-03-01T23:59:59.000Z

397

FY 2010 Volume 4  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 DOE/CF-038 Volume 4 Science May 2009 Office of Chief Financial Officer FY 2010 Congressional Budget Request Volume 4 DOE/CF-038 Volume 4 Science Printed with soy ink on recycled paper Department of Energy/ Science FY 2010 Congressional Budget Volume 4 Table of Contents Page Appropriation Account Summary.............................................................................................................3 Appropriation Language ...........................................................................................................................5 Overview...................................................................................................................................................7 Funding by Site .......................................................................................................................................21

398

FY 2012 Volume 7  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 Volume 7 Department of Energy FY 2012 Congressional Budget Request Nuclear Energy D f N l W t Di l Defense Nuclear Waste Disposal Nuclear Waste Disposal February 2011 Office of Chief Financial Officer Volume 7 Printed with soy ink on recycled paper Department of Energy/ Volume 7 FY 2012 Congressional Budget Volume 7 Table of Contents Page Appropriation Account Summary ........................................................................................................... 3

399

State Volume Price Volume Price Volume Price Volume Price Volume Price  

Gasoline and Diesel Fuel Update (EIA)

7 7 2000 2001 2002 2003 2004 State Volume Price Volume Price Volume Price Volume Price Volume Price Pipeline (Canada) Eastport, ID..................... 830,351 3.79 802,182 4.71 759,647 2.83 R 623,652 4.72 707,885 5.30 Calais, ME ...................... 123,521 4.50 152,486 4.47 124,991 3.49 R 115,301 R 5.85 102,292 6.44 Detroit, MI ....................... 6,171 3.82 405 9.34 1,948 3.56 2,514 5.96 1,117 6.27 Marysville, MI.................. 0 -- 0 -- 74 3.95 0 -- 303 7.80 St. Clair, MI..................... 17,198 4.45 21,747 4.54 28,441 3.19 5,202 5.84 22,853 6.50 International Falls, MN .... 3,022 2.77 617 4.85 602 3.01 0 -- 0 -- Noyes, MN...................... 469,361 3.75 448,898 4.19 402,621 3.09 R 359,801 5.04 399,298 5.77 Warroad, MN .................. 4,576 3.95 5,318 4.52

400

Robust, accurate, and non-contacting vibration measurement systems: Summary of comparison measurements of the robust laser interferometer and typical accelerometer systems. Volume 1  

Science Conference Proceedings (OSTI)

Epoch Engineering, Incorporated (EEI) has completed a series of vibration measurements comparing their newly-developed Robust Laser Interferometer (RLI) with accelerometer-based instrumentation systems. EEI has successfully demonstrated, on several pieces of commonplace machinery, that non-contact, line-of-sight measurements are practical and yield results equal to or, in some cases, better than customary field implementations of accelerometers. The demonstration included analysis and comparison of such phenomena as nonlinearity, transverse sensitivity, harmonics, and signal-to-noise ratio. Fast Fourier Transformations were performed on the accelerometer and the laser system outputs to provide a comparison basis. The RLI was demonstrated, within the limits of the task, to be a viable, line-of-sight, non-contact alternative to accelerometer systems. Several different kinds of machinery were instrumented and compared, including a small pump, a gear-driven cement mixer, a rotor kit, and two small fans. Known machinery vibration sources were verified and RLI system output file formats were verified to be compatible with commercial computer programs used for vibration monitoring and trend analysis. The RLI was also observed to be less subject to electromagnetic interference (EMI) and more capable at very low frequencies.

Goodenow, T.C.; Shipman, R.L.; Holland, H.M. [Epoch Engineering, Inc., Gaithersburg, MD (United States)

1995-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

FY 2012 Volume 4  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0 0 Volume 4 Department of Energy FY 2012 Congressional Budget Request Science Science February 2011 Office of Chief Financial Officer Volume 4 DOE/CF-0060 Volume 4 Department of Energy FY 2012 Congressional Budget Request Science Science February 2011 Office of Chief Financial Officer Volume 4 Printed with soy ink on recycled paper Department of Energy/ Science FY 2012 Congressional Budget Volume 4 Table of Contents Page Appropriation Account Summary .............................................................................................................3 Appropriation Language ...........................................................................................................................5 Overview ...................................................................................................................................................7

402

Managing natural gas volume analysis  

Science Conference Proceedings (OSTI)

In late 1992, Natural Gas Pipeline Co. of America and BMP Energy Systems began the joint development of a system for the automated verification and statistical correction of gas volume data captured at meter locations by flow computers. NGPL required a single system that would provide functionality for both chart processing and automated EFM data validation and correction. The pipeline company was looking for a vendor that would help develop a system to handle EFM data. The NGAS 4[trademark] system implemented at NGPL made the bridge from monthly to daily gas volume processing. The automated and rapid validation of flow data within the NGAS 4 system minimizes human intervention for validation and correction. NGPL has moved from reliance on paper chart processing to the EFM capability required in the evolving US gas market.

Parker, J. (Natural Gas Pipeline Co. of America, Lombard, IL (United States)); Treat, R. (BMP Energy Systems, Houston, TX (United States)); Bergen, H. (BMP Energy Systems, Calgary, Alberta (Canada))

1994-07-01T23:59:59.000Z

403

Assessment of generic solar thermal systems for large power applications. Volume II. Analysis of thermal energy production costs for systems from 50 to 600 MWt  

SciTech Connect

A comparative analysis of solar thermal concepts that are potentially suitable for development as large process heat systems (50 to 600 MWt) was performed. The concepts considered can be classified into three categories based on the type of solar tracking used by the collector: (1) two-axis tracking, in which concentrators track the sun's motion in both azimuth and altitude; (2) one-axis tracking, in which concentrators track changes in either azimuth or altitude; and (3) non-tracking, in which the concentrators are fixed. Seven generic types of collectors were considered. Conceptual designs developed for the seven systems were based on common assumptions of available technology in the 1990 to 2000 time frame. Costs were estimated on the basis of identical assumptions, ground rules, methodologies, and unit costs of materials and labor applied uniformly to all of the concepts.

Bird, S.P.; Apley, W.J.; Barnhart, J.S.; Brown, D.R.; Drost, M.K.; Fort, J.A.; Garrett-Price, B.A.; Williams, T.A.

1981-06-01T23:59:59.000Z

404

Assessment of generic solar thermal systems for large power applications. Volume II. Analysis of thermal energy production costs for systems from 50 to 600 MWt  

DOE Green Energy (OSTI)

A comparative analysis of solar thermal concepts that are potentially suitable for development as large process heat systems (50 to 600 MWt) was performed. The concepts considered can be classified into three categories based on the type of solar tracking used by the collector: (1) two-axis tracking, in which concentrators track the sun's motion in both azimuth and altitude; (2) one-axis tracking, in which concentrators track changes in either azimuth or altitude; and (3) non-tracking, in which the concentrators are fixed. Seven generic types of collectors were considered. Conceptual designs developed for the seven systems were based on common assumptions of available technology in the 1990 to 2000 time frame. Costs were estimated on the basis of identical assumptions, ground rules, methodologies, and unit costs of materials and labor applied uniformly to all of the concepts.

Bird, S.P.; Apley, W.J.; Barnhart, J.S.; Brown, D.R.; Drost, M.K.; Fort, J.A.; Garrett-Price, B.A.; Williams, T.A.

1981-06-01T23:59:59.000Z

405

Design and Testing of a Landfill Gas Cleanup System for Carbonate Fuel Cell Power Plants: Volume II: Full Scale Landfill Gas Cleanup for Carbonate Fuel Cell Power Plants (Proprietary)  

Science Conference Proceedings (OSTI)

This document is a proprietary version of section 5 of EPRI technical report TR-108043-V1. The volume contains detailed design information and operating conditions for a full-scale, low-cost cleanup system that would enable landfill gas to be used in carbonate fuel cells or other power generation devices. The EPRI-developed system is now available for license to commercial applications.

1998-02-27T23:59:59.000Z

406

SOLERAS - Solar Energy Water Desalination Project: Exxon Research and Engineering. System design final report, Volume 1. Design description seawater feed (System A)  

Science Conference Proceedings (OSTI)

The design of a solar powered water desalination system is presented. Design data including insolation and climate of the Yanbu, Saudi Arabia site are included. Two solar desalination designs were developed including: (1) a conceptual baseline plant powered by a solar central receiver-heliostat field, and (2) a pilot plant that demonstrates and evaluates the design features of the baseline plant. The desalination process involves a hybrid reverse osmosis/multiple effect distillation process. The performance and economics of the design plants are analyzed. (BCS)

Not Available

1985-01-01T23:59:59.000Z

407

Trenton ICES: demonstration of a grid-connected integrated community energy system. Phase II. Volumes 1 and 2. Preliminary design of ICES system and analysis of community ownership  

SciTech Connect

Preliminary design and evaluation for the system has been carried out. The findings of this study are: (1) it is technically feasible, utilizing commercially available hardware; (2) under utility ownership and operation, it will not be economically competitive with conventional alternatives for heating and cooling buildings (analysis contained in companion report under separate cover); (3) under utility ownership and operation, no restrictions have been identified that would prevent the project from proceeding; (4) under community ownership, preliminary analysis indicates that thermal energy produced by Trenton ICES will be approximately 12 percent less expensive than thermal energy produced by oil-fired boilers; and (5) a review and update of institutional analyses performed during Phase 2 has identified no factors that would preclude community ownership and operation of the Trenton ICES. The background data produced for the analysis of the Trenton ICES based on utility ownership and operation can, in large part, be used as the bases for a detailed analysis of community ownership.

1978-03-22T23:59:59.000Z

408

Illustrating surfaces in volume  

Science Conference Proceedings (OSTI)

This paper presents a novel framework for illustrating surfaces in a volume. Surfaces are illustrated by drawing only feature lines, such as silhouettes, valleys, ridges, and surface hatching strokes, and are embedded in volume renderings. This framework ...

Xiaoru Yuan; Baoquan Chen

2004-05-01T23:59:59.000Z

409

FY 2013 Volume 5  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 DOE/CF-0075 Volume 5 Environmental Management Department of Energy FY 2013 Congressional Budget Request February 2012 Office of Chief Financial Officer Volume 5 DOE/CF-0075 Volume 5 Environmental Management Printed with soy ink on recycled paper Department of Energy FY 2013 Congressional Budget Request Environmental Management Page 1 FY 2013 Congressional Budget Volume 5 Table of Contents Page Appropriation Account Summary ............................................................................................................................................ 3 Appropriation Language .......................................................................................................................................................... 5

410

FY 2007 Volume 5  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 DOE/CF-006 Volume 5 Environmental management Department of Energy FY 2007 Congressional Budget Request February 2006 Office of Chief Financial Officer Volume 5 DOE/CF-006 Volume 5 Printed with soy ink on recycled paper Environmental management Department of Energy/ Environmental Management FY 2007 Congressional Budget Volume 5 Table of Contents Page Appropriation Account Summary .........................................................................................................3 Overview................................................................................................................................................5 Defense Environmental Cleanup Appropriation Cleanup .................................................................107 Carlsbad

411

FY 2009 Volume 4  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 DOE/CF-027 Volume 4 Science February 2008 Office of Chief Financial Officer Department of Energy FY 2009 Congressional Budget Request Volume 4 DOE/CF-027 Volume 4 Science Printed with soy ink on recycled paper Department of Energy/ Science FY 2009 Congressional Budget Volume 4 Table of Contents Page Appropriation Account Summary.............................................................................................................3 Appropriation Language ...........................................................................................................................5 Overview...................................................................................................................................................7 Funding by Site

412

FY 2008 Volume 5  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 DOE/CF-018 Volume 5 Environmental Management Department of Energy FY 2008 Congressional Budget Request February 2007 Office of Chief Financial Officer Volume 5 DOE/CF-018 Volume 5 Environmental Management Printed with soy ink on recycled paper Department of Energy/ Environmental Management FY 2008 Congressional Budget Volume 5 Table of Contents Page Appropriation Account Summary.............................................................................................................3 Strategic Overview....................................................................................................................................5 Overview...................................................................................................................................................7

413

FY 2011 Volume 4  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 DOE/CF-0050 Volume 4 Science Department of Energy FY 2011 Congressional Budget Request February 2010 Office of Chief Financial Officer Volume 4 DOE/CF-0050 Volume 4 Science Printed with soy ink on recycled paper Department of Energy FY 2011 Congressional Budget Request Department of Energy/ Science FY 2011 Congressional Budget Volume 4 Table of Contents Page Appropriation Account Summary.............................................................................................................3 Appropriation Language ...........................................................................................................................5 Overview...................................................................................................................................................7

414

FY 2011 Volume 5  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 DOE/CF-0051 Volume 5 Environmental Management Department of Energy FY 2011 Congressional Budget Request February 2010 Office of Chief Financial Officer Volume 5 DOE/CF-0051 Volume 5 Environmental Management Printed with soy ink on recycled paper Department of Energy FY 2011 Congressional Budget Request Department of Energy/ Environmental Management FY 2011 Congressional Budget Volume 5 Table of Contents Page Appropriation Account Summary.............................................................................................................3 Appropriation Language ...........................................................................................................................5 Overview...................................................................................................................................................7

415

FY 2012 Volume 5  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 1 Volume 5 Department of Energy FY 2012 Congressional Budget Request Environmental Management February 2011 Office of Chief Financial Officer Volume 5 Printed with soy ink on recycled paper Environmental Management FY 2011 Congressional Budget Volume 5 Table of Contents Page Appropriation Account Summary .............................................................................................................3

416

Emissions of volatile and potentially toxic organic compounds from waste-water treatment plants and collection systems (Phase 2). Volume 3. Waste-water treatment-plant emissions. Experimental phase. Final report  

SciTech Connect

Volume 3 describes the measurements and experimental data obtained to assess emissions from various points within a POTW. Included are a discussion of sampling methods development, emissions studies of activated carbon bed odor control units located at various points of a large municipal wastewater treatment plant and its collection system, upwind/downwind sampling from an activated sludge aeration basins at a large municipal wastewater treatment plant, and preliminary studies of haloform formation as a result of chlorination of wastewater.

Chang, D.P.Y.; Guensler, R.; Kim, J.O.; Chou, T.L.; Uyeminami, D.

1991-08-01T23:59:59.000Z

418

Energy Efficient Laboratory Fume Hood  

Allows use of small HVAC systems ; Avoids expensive control systems required by VAV fume hoods ; ABSTRACT: Fume hoods, used to protect the ...

419

Site Environmental Report for 2005 Volume I and Volume II  

SciTech Connect

Each year, Ernest Orlando Lawrence Berkeley National Laboratory prepares an integrated report on its environmental programs to satisfy the requirements of United States Department of Energy Order 231.1A, ''Environment, Safety, and Health Reporting''. The ''Site Environmental Report for 2005'' summarizes Berkeley Lab's environmental management performance, presents environmental monitoring results, and describes significant programs for calendar year 2005. (Throughout this report, Ernest Orlando Lawrence Berkeley National Laboratory is referred to as ''Berkeley Lab'', ''the Laboratory'', ''Lawrence Berkeley National Laboratory'', and ''LBNL''.) The report is separated into two volumes. Volume I contains an overview of the Laboratory, the status of environmental programs, and summarized results from surveillance and monitoring activities. This year's Volume I text body is organized into an executive summary followed by six chapters. The report's structure has been reorganized this year, and it now includes a chapter devoted to environmental management system topics. Volume II contains individual data results from surveillance and monitoring activities. The ''Site Environmental Report'' is distributed by releasing it on the Web from the Berkeley Lab Environmental Services Group (ESG) home page, which is located at http://www.lbl.gov/ehs/esg/. Many of the documents cited in this report also are accessible from the ESG Web page. CD and printed copies of this Site Environmental Report are available upon request. The report follows the Laboratory's policy of using the International System of Units (SI), also known as the metric system of measurements. Whenever possible, results are also reported using the more conventional (non-SI) system of measurements, because the non-SI system is referenced by several current regulatory standards and is more familiar to some readers. Two tables are provided at the end of the Glossary to help readers: the first defines the prefixes used with SI units of measurement, and the second provides conversions to non-SI units.

Ruggieri, Michael

2006-07-07T23:59:59.000Z

420

October 23, 2012 11:49 World Scientific Review Volume -9in x 6in ywangsmartgrid Smart Grid, Automation, and SCADA Systems Security  

E-Print Network (OSTI)

SCADA protocols: SCADA devices are man- ufactured by different vendors with different proprietary:49 World Scientific Review Volume - 9in x 6in ywangsmartgrid SCADA Security 13 3.3. sSCADA protocol suite The sSCADA protocol suite19 is proposed to overcome the challenges that we have discussed

Wang, Yongge

Note: This page contains sample records for the topic "volume vav system" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

District heating and cooling systems for communities through power plant retrofit distribution network. Phase 2. Final report, 1 March 1980-31 January 1984. Volume VII. Appendix C  

SciTech Connect

This volume contains: Hudson No. 2 Limited Retrofit Cost Estimates provided by Stone and Webster Engineering Corp. (SWEC); backup data and basis of estimate for SWEC Heater Plant and Gas Turbine Plant (Kearny No. 12) cost estimates; and Appendices - Analysis of Relevant Tax Laws.

Not Available

1984-01-31T23:59:59.000Z

422

FY 2013 Volume 2  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2 2 Volume 2 f Department of Energy FY 2013 Congressional B d R Budget Request Other Defense Activities Departmental Administration Inspector General Working Capital F nd Working Capital Fund Safeguards and Security Crosscut Pensions February 2012 Office of Chief Financial Officer Volume 2 DOE/CF-0072 Volume 2 f Department of Energy FY 2013 Congressional B d R Budget Request Other Defense Activities Departmental Administration Inspector General Working Capital F nd Working Capital Fund Safeguards and Security Crosscut Pensions February 2012 Office of Chief Financial Officer Volume 2 Printed with soy ink on recycled paper Department of Energy/ Volume 2 FY 2013 Congressional Budget Volume 2 Table of Contents Page Appropriation Account Summary .............................................................................................................3

423

FY 2012 Volume 3  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9 9 Volume 3 Department of Energy FY 2012 Congressional Budget Request Energy Efficiency and Renewable Energy Electricity Delivery and Energy Reliability Energy Transformation Acceleration Fund Energy Transformation Acceleration Fund Fossil Energy Research and Development Naval Petroleum and Oil Shale Reserves Strategic Petroleum Reserve Northeast Home Heating Oil Reserve Ultra-Deepwater Unconventional Natural Gas February 2011 Office of Chief Financial Officer Volume 3 Printed with soy ink on recycled paper Department of Energy/ Volume 3 FY 2012 Congressional Budget Volume 3 Table of Contents Page Appropriation Account Summary .............................................................................................................3

424

FY 2005 Volume 1  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2 2 Volume 1 February 2004 Volume 1 National Nuclear Security Administration National Nuclear Security Administration Office of the Administrator Office of the Administrator Weapons Activities Weapons Activities Defense Nuclear Nonproliferation Defense Nuclear Nonproliferation Naval Reactors Naval Reactors Office of Management, Budget and Evaluation/CFO Department of Energy Department of Energy FY 2005 Congressional Budget FY 2005 Congressional Budget Request Request DOE/ME-0032 Volume 1 February 2004 Volume 1 Office of Management, Budget and Evaluation/CFO Printed with soy ink on recycled paper National Nuclear Security Administration National Nuclear Security Administration Office of the Administrator Office of the Administrator Weapons Activities Weapons Activities Defense Nuclear Nonproliferation

425

FY 2009 Volume 1  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 1 DOE/CF-024 Volume 1 National Nuclear Security Administration Office of the Administrator Weapons Activities Defense Nuclear Nonproliferation Naval Reactors February 2008 Office of Chief Financial Officer Department of Energy FY 2009 Congressional Budget Request Volume 1 DOE/CF-024 Volume 1 National Nuclear Security Administration Office of the Administrator Weapons Activities Defense Nuclear Nonproliferation Naval Reactors Printed with soy ink on recycled paper Office of the Administrator Weapons Activities Defense Nuclear Nonproliferation Naval Reactors Office of the Administrator Weapons Activities Defense Nuclear Nonproliferation Naval Reactors Department of Energy/ National Nuclear Security Administration FY 2009 Congressional Budget Volume 1 Table of Contents

426

FY 2010 Volume 3  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 DOE/CF-037 Volume 3 Energy Efficiency and Renewable Energy Electricity Delivery and Energy Reliability Energy Transformation Acceleration Fund Nuclear Energy May 2009 Office of Chief Financial Officer FY 2010 Congressional Budget Request Volume 3 DOE/CF-037 Volume 3 Energy Efficiency and Renewable Energy Electricity Delivery and Energy Reliability Energy Transformation Acceleration Fund Nuclear Energy Printed with soy ink on recycled paper Energy Efficiency and Renewable Energy Electricity Delivery and Energy Reliability Energy Transformation Acceleration Fund Nuclear Energy Energy Efficiency and Renewable Energy Electricity Delivery and Energy Reliability Energy Transformation Acceleration Fund Nuclear Energy Department of Energy/ Volume 3 FY 2010 Congressional Budget

427

FY 2012 Volume 2  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8 8 Volume 2 f Department of Energy FY 2012 Congressional B d R Budget Request Other Defense Activities Other Defense Activities Departmental Administration Inspector General Advanced Technology Vehicles Manufacturing Loan Program Title 17 Innovative Technology Loan Guarantee Program Better Building Pilot Loan Guarantee Initiative for Universities Schools and Hospitals Universities, Schools, and Hospitals Working Capital Fund Energy Information Administration Safeguards and Security Crosscut February 2011 Office of Chief Financial Officer Volume 2 g y Pensions Printed with soy ink on recycled paper Department of Energy/ Volume 2 FY 2012 Congressional Budget Volume 2 Table of Contents Page Appropriation Account Summary .............................................................................................................3

428

FY 2007 Volume 1  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Chief Financial Officer Chief Financial Officer Volume 1 DOE/CF-002 Volume 1 National Nuclear Security Administration Office of the Administrator Weapons Activities Defense Nuclear Nonproliferation Naval Reactors Printed with soy ink on recycled paper Department of Energy FY 2007 Congressional Budget Request February 2006 Office of Chief Financial Officer Volume 1 DOE/CF-002 Volume 1 National Nuclear Security Administration Office of the Administrator Weapons Activities Defense Nuclear Nonproliferation Naval Reactors Office of the Administrator Weapons Activities Defense Nuclear Nonproliferation Naval Reactors Office of the Administrator Weapons Activities Defense Nuclear Nonproliferation Naval Reactors Department of Energy/ National Nuclear Security Administration FY 2007 Congressional Budget

429

FY 2010 Volume 5  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 DOE/CF-039 Volume 5 Environmental Management Defense Nuclear Waste Disposal Nuclear Waste Disposal May 2009 Office of Chief Financial Officer FY 2010 Congressional Budget Request Volume 5 DOE/CF-039 Volume 5 Environmental Management Defense Nuclear Waste Disposal Nuclear Waste Disposal Printed with soy ink on recycled paper Environmental Management Defense Nuclear Waste Disposal Nuclear Waste Disposal Environmental Management Defense Nuclear Waste Disposal Nuclear Waste Disposal Department of Energy FY 2010Congressional Budget Environmental Management/ Defense Nuclear Waste/Nuclear Waste Disposal Volume 5 Table of Contents Page Appropriation Account Summary.............................................................................................................3

430

FY 2013 Volume 6  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6 6 Volume 6 Department of Energy FY 2013 Congressional Budget Request Power Marketing Administrations Southeastern Power Administration Southwestern Power Administration Western Area Power Administration Western Area Power Administration Bonneville Power Administration February 2012 Office of Chief Financial Officer Volume 6 DOE/CF-0076 Volume 6 Department of Energy FY 2013 Congressional Budget Request Power Marketing Administrations Southeastern Power Administration Southwestern Power Administration Western Area Power Administration Western Area Power Administration Bonneville Power Administration February 2012 Office of Chief Financial Officer Volume 6 Printed with soy ink on recycled paper Southeastern Power Administration Southwestern Power Administration Western Area Power Administration

431

FY 2007 Volume 4  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 DOE/CF-005 Volume 4 Science Nuclear waste disposal Defense nuclear waste disposal Departmental administration Inspector general Working capital fund Department of Energy FY 2007 Congressional Budget Request February 2006 Office of Chief Financial Officer Volume 4 DOE/CF-005 Volume 4 Printed with soy ink on recycled paper Science Nuclear waste disposal Defense nuclear waste disposal Departmental administration Inspector general Working capital fund Science Nuclear Waste Disposal Defense Nuclear Waste Disposal Departmental Administration Inspector General Working Capital Fund Science Nuclear Waste Disposal Defense Nuclear Waste Disposal Departmental Administration Inspector General Working Capital Fund Department of Energy FY 2007 Congressional Budget Volume 4 Table of Contents

432

FY 2013 Volume 4  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 DOE/CF-0074 Volume 4 Science Advanced Research Projects Agency-Energy Department of Energy FY 2013 Congressional Budget Request February 2012 Office of Chief Financial Officer Volume 4 DOE/CF-0074 Volume 4 Science Advanced Research Projects Agency-Energy Printed with soy ink on recycled paper Department of Energy FY 2013 Congressional Budget Request Science Advanced Research Projects Agency- Energy Science Advanced Research Projects Agency- Energy Department of Energy/Science/ Advanced Research Projects Agency - Energy FY 2013 Congressional Budget Volume 4 Table of Contents Page Appropriation Account Summary ............................................................................................................................................ 3

433

FY 2008 Volume 1  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 1 DOE/CF-014 Volume 1 National Nuclear Security Administration Office of the Administrator Weapons Activities Defense Nuclear Nonproliferation Naval Reactors Department of Energy FY 2008 Congressional Budget Request February 2007 Office of Chief Financial Officer Volume 1 DOE/CF-014 Volume 1 National Nuclear Security Administration Office of the Administrator Weapons Activities Defense Nuclear Nonproliferation Naval Reactors Printed with soy ink on recycled paper Office of the Administrator Weapons Activities Defense Nuclear Nonproliferation Naval Reactors Office of the Administrator Weapons Activities Defense Nuclear Nonproliferation Naval Reactors Department of Energy/ National Nuclear Security Administration FY 2008 Congressional Budget Volume 1 Table of Contents

434

FY 2006 Volume 4  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Science Science Nuclear Waste Disposal Defense Nuclear Waste Disposal Departmental Administration Inspector General Working Capital Fund Office of Management, Budget and Evaluation/CFO Volume 4 February 2005 DOE/ME-0049 Volume 4 Department of Energy FY 2006 Congressional Budget Request Science Nuclear Waste Disposal Defense Nuclear Waste Disposal Departmental Administration Inspector General Working Capital Fund Office of Management, Budget and Evaluation/CFO Volume 4 February 2005 DOE/ME-0049 Volume 4 Printed with soy ink on recycled paper Science Nuclear Waste Disposal Defense Nuclear Waste Disposal Departmental Administration Inspector General Working Capital Fund Science Nuclear Waste Disposal Defense Nuclear Waste Disposal Departmental Administration Inspector General Working Capital Fund

435

FY 2010 Volume 1  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 1 DOE/CF-035 Volume 1 National Nuclear Security Administration Office of the Administrator Weapons Activities Defense Nuclear Nonproliferation Naval Reactors May 2009 Office of Chief Financial Officer FY 2010 Congressional Budget Request Volume 1 DOE/CF-035 Volume 1 National Nuclear Security Administration Office of the Administrator Weapons Activities Defense Nuclear Nonproliferation Naval Reactors Printed with soy ink on recycled paper Office of the Administrator Weapons Activities Defense Nuclear Nonproliferation Naval Reactors Office of the Administrator Weapons Activities Defense Nuclear Nonproliferation Naval Reactors Department of Energy/ National Nuclear Security Administration FY 2010 Congressional Budget Volume 1 Table of Contents Page Appropriation Account Summary.............................................................................................................3

436

FY 2013 Volume 3  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 DOECF-0073 Volume 3 Printed with soy ink on recycled paper Department of Energy FY 2013 Congressional Budget Request Energy Efficiency and Renewable Energy Electricity Delivery...

437

LANL Volume 2_Final  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Emergency Management Programs at the Los Alamos National Laboratory Office of Independent Oversight and Performance Assurance Office of the Secretary of Energy April 2002 Volume II...

438

Nuclear proliferation and civilian nuclear power: report of the Nonproliferation Alternative Systems Assessment Program. Volume III. Resources and fuel cycle facilities  

SciTech Connect

Volume III explores resources and fuel cycle facilities. Chapters are devoted to: estimates of US uranium resources and supply; comparison of US uranium demands with US production capability forecasts; estimates of foreign uranium resources and supply; comparison of foreign uranium demands with foreign production capability forecasts; and world supply and demand for other resources and fuel cycle services. An appendix gives uranium, fissile material, and separative work requirements for selected reactors and fuel cycles.

1979-12-01T23:59:59.000Z

439

IEA Wind Task 24 Integration of Wind and Hydropower Systems; Volume 1: Issues, Impacts, and Economics of Wind and Hydropower Integration  

DOE Green Energy (OSTI)

This report describes the background, concepts, issues and conclusions related to the feasibility of integrating wind and hydropower, as investigated by the members of IEA Wind Task 24. It is the result of a four-year effort involving seven IEA member countries and thirteen participating organizations. The companion report, Volume 2, describes in detail the study methodologies and participant case studies, and exists as a reference for this report.

Acker, T.

2011-12-01T23:59:59.000Z