Powered by Deep Web Technologies
Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

The Accuracy of Vertical Air Velocities from Doppler Radar Data  

Science Conference Proceedings (OSTI)

Eight methods of calculating vertical air velocity in a column are compared. Each method requires some or all of the following data: horizontal divergence, vertical precipitation velocity, hydrometeor terminal fall speed, and vertical air ...

Thomas Matejka; Diana L. Bartels

1998-01-01T23:59:59.000Z

2

A Hypothetical Burning-Velocity Formula for Very Lean Hydrogen-Air Mixtures  

E-Print Network (OSTI)

R.W. Shefer, Int. J. Hydrogen Energy 28 (2003) 1131-1141. P.burning velocities of lean hydrogen-air flames at 1 atm andFORMULA FOR VERY LEAN HYDROGEN-AIR MIXTURES by Forman A.

Grcar, Joseph F

2008-01-01T23:59:59.000Z

3

New Developments in High Velocity Air-fuel Spraying  

Science Conference Proceedings (OSTI)

This is possible because of the low temperature of air-fuel combustion. The heating of the spray ... Conditioning of Composite Lubricant Powder for Cold Spray.

4

Effect of wave boundary layer on sea-to-air dimethylsulfide transfer velocity during typhoon passage  

E-Print Network (OSTI)

: Dimethylsulfide; Sea-to-air gas transfer velocity; Wave boundary layer; Tropical cyclone; Drag coefficient in order to accurately calculate aerosol radiative forcing. The sea-to-air DMS flux depends on airside coefficient CD and roughness length z0 has been investigated over small areas of the sea or in wave tanks

Chu, Peter C.

5

Design of passively aerated compost piles: Vertical air velocities between the pipes  

Science Conference Proceedings (OSTI)

Passively aerated compost piles are built on a base of porous materials, such as straw or wood chips, in which perforated air supply pipes are distributed. The piles are not turned during composting, nor is forced-aeration equipment used, which significantly reduces the operating and capital expenses associated with these piles. Currently, pile configurations and materials are worked out by trial and error. Fundamentally based design procedures are difficult to develop because the natural convection air flow rate is not explicitly known, but rather is closely coupled with the pile temperature. This paper develops a mathematical model to analytically determine the maximum upward air flow velocity over an air supply pipe and the drop in vertical velocity away from the pipe. This model has one dimensionless number, dependent on the pile and base properties, which fully characterizes the velocity profile between the pipes. 9 refs., 4 figs., 1 tab.

Lynch, N.J.; Cherry, R.S. [Idaho National Engineering Lab., Idaho Falls, ID (United States)

1996-09-01T23:59:59.000Z

6

Velocity  

Science Conference Proceedings (OSTI)

... Delta t ffl \\Delta t = 1ns. Pulse-Dri ven Wall Motion ( ff = ... varies, can increase (!), eventually decays tozero. Pulse-Dri ven Domain Wall Velocity ( ff = ...

2004-01-16T23:59:59.000Z

7

A HYPOTHETICAL BURNING-VELOCITY FORMULA FOR VERY LEAN HYDROGEN-AIR MIXTURES  

E-Print Network (OSTI)

1 A HYPOTHETICAL BURNING-VELOCITY FORMULA FOR VERY LEAN HYDROGEN-AIR MIXTURES by Forman A. Williams experience strong diffusive-thermal types of cellular instabilities that tend to increase the laminar burning propagating, planar, hexagonal, close-packed array of flame balls, each burning as if it were an isolated

Geddes, Cameron Guy Robinson

8

Laminar burning velocities and flame instabilities of butanol isomers-air mixtures  

SciTech Connect

Laminar burning velocities and flame instabilities of the butanol-air premixed flames and its isomers are investigated using the spherically expanding flame with central ignition at initial temperature of 428 K and initial pressures of 0.10 MPa, 0.25 MPa, 0.50 MPa and 0.75 MPa. Laminar burning velocities and sensitivity factor of n-butanol-air mixtures are computed using a newly developed kinetic mechanism. Unstretched laminar burning velocity, adiabatic temperature, Lewis number, Markstein length, critical flame radius and Peclet number are obtained over a wide range of equivalence ratios. Effect of molecular structure on laminar burning velocity of the isomers of butanol is analyzed from the aspect of C-H bond dissociation energy. Study indicates that although adiabatic flame temperatures of the isomers of butanol are the same, laminar burning velocities give an obvious difference among the isomers of butanol. This indicates that molecular structure has a large influence on laminar burning velocities of the isomers of butanol. Branching (-CH3) will decrease laminar burning velocity. Hydroxyl functional group (-OH) attaching to the terminal carbon atoms gives higher laminar burning velocity compared to that attaching to the inner carbon atoms. Calculated dissociation bond energies show that terminal C-H bonds have larger bond energies than that of inner C-H bonds. n-Butanol, no branching and with hydroxyl functional group (-OH) attaching to the terminal carbon atom, gives the largest laminar burning velocity. tert-Butanol, with highly branching and hydroxyl functional group (-OH) attaching to the inner carbon atom, gives the lowest laminar burning velocity. Laminar burning velocities of iso-butanol and sec-butanol are between those of n-butanol and tert-butanol. The instant of transition to cellularity is experimentally determined for the isomers of butanol and subsequently interpreted on the basis of hydrodynamic and diffusion-thermal instabilities. Little effect on flame instability is observed for the isomers of butanol. Critical flame radii are the same for the isomers of butanol. Peclet number decreases with the increase in equivalence ratio. (author)

Gu, Xiaolei; Huang, Zuohua; Wu, Si; Li, Qianqian [State Key Laboratory of Multiphase Flow in Power Engineering, Xi'an Jiaotong University, Xi'an 710049 (China)

2010-12-15T23:59:59.000Z

9

A Hypothetical Burning-Velocity Formula for Very Lean Hydrogen-Air Mixtures  

SciTech Connect

Very lean hydrogen-air mixtures experience strong diffusive-thermal types of cellular instabilities that tend to increase the laminar burning velocity above the value that applies to steady, planar laminar flames that are homogeneous in transverse directions. Flame balls constitute an extreme limit of evolution of cellular flames. To account qualitatively for the ultimate effect of diffusive-thermal instability, a model is proposed in which the flame is a steadily propagating, planar, hexagonal, close-packed array of flame balls, each burning as if it were an isolated, stationary, ideal flame ball in an infinite, quiescent atmosphere. An expression for the laminar burning velocity is derived from this model, which theoretically may provide an upper limit for the experimental burning velocity.

Williams, Forman; Williams, Forman A; Grcar, Joseph F

2008-06-30T23:59:59.000Z

10

A Hypothetical Burning-Velocity Formula for Very Lean Hydrogen-Air Mixtures  

E-Print Network (OSTI)

K. Fig. 2 Comparisons of burning-velocity predictions withcurve), when an experimental burning velocity (points) of 53and calculated laminar burning velocities of lean hydrogen-

Grcar, Joseph F

2008-01-01T23:59:59.000Z

11

Effects of flow transients on the burning velocity of hydrogen-air premixed flames  

DOE Green Energy (OSTI)

The effects of unsteady strain rate on the burning velocity of hydrogen-air premixed flames are studied in an opposed nozzle configuration. The numerical method employs adaptive time integration of a system of differential-algebraic equations. Detailed hydrogen-air kinetic mechanism and transport properties are considered. The equivalence ratio is varied from lean to rich premixtures in order to change the effective Lewis number. Steady Markstein numbers for small strain rate are computed and compared with experiment. Different definitions of flame burning velocity are examined under steady and unsteady flow conditions. It is found that, as the unsteady frequency increases, large deviations between different flame speeds are noted depending on the location of the flame speed evaluation. Unsteady flame response is investigated in terms of the Markstein transfer function which depends on the frequency of oscillation. In most cases, the flame speed variation attenuates at higher frequencies, as the unsteady frequency becomes comparable to the inverse of the characteristic flame time. Furthermore, unique resonance-like behavior is observed for a range of rich mixture conditions, consistent with previous studies with linearized theory.

H. G. Im; J. H. Chen

2000-07-30T23:59:59.000Z

12

Measuring OutdoorAir Intake Rates Using Electronic Velocity Sensors at Louvers and Downstream of Airflow Straighteners  

SciTech Connect

Practical and accurate technologies are needed for continuously measuring and controlling outdoor air (OA) intake rates in commercial building heating, ventilating, and air conditioning (HVAC) systems. This project evaluated two new measurement approaches. Laboratory experiments determined that OA flow rates were measurable with errors generally less than 10percent using electronic air velocity probes installed between OA intake louver blades or at the outlet face of louvers. High accuracy was maintained with OA flow rates as low as 15percent of the maximum for the louvers. Thus, with this measurement approach HVAC systems do not need separate OA intakes for minimum OA supply. System calibration parameters are required for each unique combination of louver type and velocity sensor location but calibrations are not necessary for each system installation. The research also determined that the accuracy of measuring OA flow rates with velocity probes located in the duct downstream of the intake louver was not improved by installing honeycomb airflow straighteners upstream of the probes. Errors varied with type of upstream louver, were as high as 100percent, and were often greater than 25percent. In conclusion, use of electronic air velocity probes between the blades of OA intake louvers or at the outlet face of louvers is a highly promising means of accurately measuring rates of OA flow into HVAC systems. The use of electronic velocity probes downstream of airflow straighteners is less promising, at least with the relatively small OA HVAC inlet systems employed in this research.

Fisk, William; Sullivan, Douglas; Cohen, Sebastian; Han, Hwataik

2008-10-01T23:59:59.000Z

13

Velocity Fields of Axisymmetric Hydrogen-Air Counterflow Diffusion Flames From LDV, PIV, and Numerical Computation  

Science Conference Proceedings (OSTI)

Laminar fuel-air counterflow diffusion flames (CFDFs) were studied using axisymmetric convergent-nozzle and straight-tube opposed jet burners (OJBs). The subject diagnostics were used to probe a systematic set of H2/N2-air CFDFs over wide ranges of fuel ...

Pellett Gerald L.; Wilson Lloyd G.; Jr William M. Humphreys; Bartram Scott M.; Gartrell Luther R.; Isaac K. M.

1995-07-01T23:59:59.000Z

14

Correlation of turbulent burning velocities of ethanol-air, measured in a fan-stirred bomb up to 1.2 MPa  

SciTech Connect

The turbulent burning velocity is defined by the mass rate of burning and this also requires that the associated flame surface area should be defined. Previous measurements of the radial distribution of the mean reaction progress variable in turbulent explosion flames provide a basis for definitions of such surface areas for turbulent burning velocities. These inter-relationships. in general, are different from those for burner flames. Burning velocities are presented for a spherical flame surface, at which the mass of unburned gas inside it is equal to the mass of burned gas outside it. These can readily be transformed to burning velocities based on other surfaces. The measurements of the turbulent burning velocities presented are the mean from five different explosions, all under the same conditions. These cover a wide range of equivalence ratios, pressures and rms turbulent velocities for ethanol-air mixtures. Two techniques are employed, one based on measurements of high speed schlieren images, the other on pressure transducer measurements. There is good agreement between turbulent burning velocities measured by the two techniques. All the measurement are generalised in plots of burning velocity normalised by the effective unburned gas rms velocity as a function of the Karlovitz stretch factor for different strain rate Markstein numbers. For a given value of this stretch factor a decrease in Markstein number increases the normalised burning velocity. Comparisons are made with the findings of other workers. (author)

Bradley, D.; Lawes, M.; Mansour, M.S. [School of Mechanical Engineering, University of Leeds (United Kingdom)

2011-01-15T23:59:59.000Z

15

Single-Doppler Velocity Retrievals with Phoenix II Data: Clear Air and Microburst Wind Retrievals in the Planetary Boundary Layer  

Science Conference Proceedings (OSTI)

A new three-dimensional single-Doppler velocity retrieval is introduced and tested with reflectivity and radial velocity data gathered during the Phoenix II field program near Boulder, Colorado. This retrieval is based on reflectivity ...

Alan Shapiro; Scott Ellis; Justin Shaw

1995-05-01T23:59:59.000Z

16

Influence of the inlet velocity profiles on the prediction of velocity distribution inside an electrostatic precipitator  

SciTech Connect

The influence of the velocity profile at the inlet boundary on the simulation of air velocity distribution inside an electrostatic precipitator is presented in this study. Measurements and simulations were performed in a duct and an electrostatic precipitator (ESP). A four-hole cobra probe was used for the measurement of velocity distribution. The flow simulation was performed by using the computational fluid dynamics (CFD) code FLUENT. Numerical calculations for the air flow were carried out by solving the Reynolds-averaged Navier-Stokes equations coupled with the realizable k-{epsilon} turbulence model equations. Simulations were performed with two different velocity profiles at the inlet boundary - one with a uniform (ideal) velocity profile and the other with a non-uniform (real) velocity profile to demonstrate the effect of velocity inlet boundary condition on the flow simulation results inside an ESP. The real velocity profile was obtained from the velocity measured at different points of the inlet boundary whereas the ideal velocity profile was obtained by calculating the mean value of the measured data. Simulation with the real velocity profile at the inlet boundary was found to predict better the velocity distribution inside the ESP suggesting that an experimentally measured velocity profile could be used as velocity inlet boundary condition for an accurate numerical simulation of the ESP. (author)

Haque, Shah M.E.; Deev, A.V.; Subaschandar, N. [Process Engineering and Light Metals (PELM) Centre, Faculty of Sciences, Engineering and Health, Central Queensland University, Gladstone, Queensland 4680 (Australia); Rasul, M.G.; Khan, M.M.K. [College of Engineering and Built Environment, Faculty of Sciences, Engineering and Health, Central Queensland University, Rockhampton, Queensland 4702 (Australia)

2009-01-15T23:59:59.000Z

17

Simultaneous Measurements of Drop Size and Velocity in ...  

Science Conference Proceedings (OSTI)

... of entrained air velocity. An example is presented in Prahl and Wendt (1988) and Wendt and Prahl (1986) where the authors ...

18

Probe measurements of the ionization of air behind strong shocks  

SciTech Connect

Detailed measurements of the ionization of air behind strong shocks over a broad range of shocks velocities are reported. (AIP)

Gorelov, V.A.; Kil' dyushova, L.A.

1981-11-01T23:59:59.000Z

19

TEE-0010  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4, 2004 4, 2004 DECISION AND ORDER OFFICE OF HEARINGS AND APPEALS Applications for Exception Case Names: SpacePak Unico, Inc. Date of Filing: May 24, 2004 Case Numbers: TEE-0010 TEE-0011 This Decision and Order considers Applications for Exception filed by SpacePak and Unico, Inc. (Unico), seeking exception relief from the provisions of in C.F.R. Part 430, pertaining to energy conservation standards for central air conditioners and heat pumps (Air Conditioner Standards). SpacePak and Unico are manufacturers of small duct, high velocity (SDHV) air conditioning equipment. In their exception requests, SpacePak and Unico assert that they will suffer a serious hardship and an unfair distribution of burdens if forced to comply with the 13 SEER energy efficiency standard effective January 2006, 10 C.F.R. § 430.32(c). If their Applications for Exception were

20

TEA-0008 - In the Matter of Unico, Inc. | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

08 - In the Matter of Unico, Inc. 08 - In the Matter of Unico, Inc. TEA-0008 - In the Matter of Unico, Inc. The present Appeal filed by Unico, Inc. (Unico), relates to a Decision and Order issued by the Office of Hearings and Appeals (OHA) on December 20, 2005, granting exception relief to Energy Savings Products, Ltd. (ESP) from the provisions of 10 C.F.R. Part 430, pertaining to energy conservation standards for central air conditioners and heat pumps (Air Conditioner Standards). Energy Savings Products, Ltd., 29 DOE & 81,015 (2005) (ESP). ESP sought and obtained exception relief on the basis that the firm is a manufacturer of small duct, high velocity (SDHV) air conditioning equipment, and would suffer a gross inequity, serious hardship and an unfair distribution of burdens if forced to comply with

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

TEE-0026 - In the Matter of Energy Savings Products, Ltd. | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6 - In the Matter of Energy Savings Products, Ltd. 6 - In the Matter of Energy Savings Products, Ltd. TEE-0026 - In the Matter of Energy Savings Products, Ltd. This Decision and Order considers an Application for Exception filed by Energy Savings Products, Ltd. (ESP) seeking exception relief from the provisions of 10 C.F.R. Part 430, pertaining to energy conservation standards for central air conditioners and heat pumps (Air Conditioner Standards). ESP is a manufacturer of small duct, high velocity (SDHV) air conditioning equipment. In its exception request, ESP asserts that the firm will suffer a gross inequity, serious hardship and an unfair distribution of burdens if forced to comply with the 13 SEER energy efficiency standard effective January 2006, 10 C.F.R. § 430.32(c). If its Application for Exception were granted, the

22

TEE-0011 - In the Matter of Unico, Inc. | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 - In the Matter of Unico, Inc. 1 - In the Matter of Unico, Inc. TEE-0011 - In the Matter of Unico, Inc. This Decision and Order considers Applications for Exception filed by SpacePak and Unico, Inc. (Unico), seeking exception relief from the provisions of in C.F.R. Part 430, pertaining to energy conservation standards for central air conditioners and heat pumps (Air Conditioner Standards). SpacePak and Unico are manufacturers of small duct, high velocity (SDHV) air conditioning equipment. In their exception requests, SpacePak and Unico assert that they will suffer a serious hardship and an unfair distribution of burdens if forced to comply with the 13 SEER energy efficiency standard effective January 2006, 10 C.F.R. § 430.32(c). If their Applications for Exception were granted, the firms would receive exception relief from the revised

23

P:\DECISION\0026.tee.wpd  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

, 2005 , 2005 DECISION AND ORDER OFFICE OF HEARINGS AND APPEALS Application for Exception Case Name: Energy Savings Products, Ltd. Date of Filing: September 28, 2005 Case Number: TEE-0026 This Decision and Order considers an Application for Exception filed by Energy Savings Products, Ltd. (ESP) seeking exception relief from the provisions of 10 C.F.R. Part 430, pertaining to energy conservation standards for central air conditioners and heat pumps (Air Conditioner Standards). ESP is a manufacturer of small duct, high velocity (SDHV) air conditioning equipment. In its exception request, ESP asserts that the firm will suffer a gross inequity, serious hardship and an unfair distribution of burdens if forced to comply with the 13 SEER energy efficiency standard effective

24

Microsoft Word - 0008.tea.wpd  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

June 30, 2006 June 30, 2006 DECISION AND ORDER OFFICE OF HEARINGS AND APPEALS Appeal Case Name: Unico, Inc. Date of Filing: January 19, 2006 Case Number: TEA-0008 The present Appeal filed by Unico, Inc. (Unico), relates to a Decision and Order issued by the Office of Hearings and Appeals (OHA) on December 20, 2005, granting exception relief to Energy Savings Products, Ltd. (ESP) from the provisions of 10 C.F.R. Part 430, pertaining to energy conservation standards for central air conditioners and heat pumps (Air Conditioner Standards). Energy Savings Products, Ltd., 29 DOE & 81,015 (2005) (ESP). ESP sought and obtained exception relief on the basis that the firm is a manufacturer of small duct, high velocity (SDHV) air conditioning equipment, and would suffer a gross inequity,

25

TEE-0010 - In the Matter of SpacePak | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0 - In the Matter of SpacePak 0 - In the Matter of SpacePak TEE-0010 - In the Matter of SpacePak This Decision and Order considers Applications for Exception filed by SpacePak and Unico, Inc. (Unico), seeking exception relief from the provisions of in C.F.R. Part 430, pertaining to energy conservation standards for central air conditioners and heat pumps (Air Conditioner Standards). SpacePak and Unico are manufacturers of small duct, high velocity (SDHV) air conditioning equipment. In their exception requests, SpacePak and Unico assert that they will suffer a serious hardship and an unfair distribution of burdens if forced to comply with the 13 SEER energy efficiency standard effective January 2006, 10 C.F.R. § 430.32(c). If their Applications for Exception were granted, the firms would receive exception relief from the revised

26

ARM - Evaluation Product - Convective Vertical Velocity  

NLE Websites -- All DOE Office Websites (Extended Search)

ProductsConvective Vertical Velocity ProductsConvective Vertical Velocity Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Evaluation Product : Convective Vertical Velocity 2011.04.25 - 2011.05.23 Site(s) SGP General Description Convective processes play an important role in Earth's energy balance by distributing heat and moisture throughout the atmosphere. In particular, vertical air motions associated with these processes are inherently linked to the life cycle of these convective systems and are therefore directly tied to their energy budget. However, direct measurements of vertical air motions (e.g., in situ aircraft observations) are sparse, making it difficult to compare them with numerical model output, which relies on convective parameterization schemes that have yet to be extensively

27

Fiber Optic Velocity Interferometry  

SciTech Connect

This paper explores the use of a new velocity measurement technique that has several advantages over existing techniques. It uses an optical fiber to carry coherent light to and from a moving target. A Fabry-Perot interferometer, formed by a gradient index lens and the moving target, produces fringes with a frequency proportional to the target velocity. This technique can measure velocities up to 10 km/s, is accurate, portable, and completely noninvasive.

Neyer, Barry T.

1988-04-01T23:59:59.000Z

28

Efficient Dealiasing of Doppler Velocities Using Local Environment Constraints  

Science Conference Proceedings (OSTI)

A Doppler velocity dealiasing algorithm is described that processes one radial at a time by comparing that radial with a previous radial. This technique has worked reliably on numerous Doppler radar datasets for clear air, thunderstorm, and ...

Michael D. Eilts; Steven D. Smith

1990-02-01T23:59:59.000Z

29

Vertical Velocity Focus Group  

NLE Websites -- All DOE Office Websites (Extended Search)

Velocity Focus Group Velocity Focus Group ARM 2008 Science Team Meeting Norfolk, VA March 10-14 Background Vertical velocity measurements have been at the top of the priority list of the cloud modeling community for some time. Doppler measurements from ARM profiling radars operating at 915-MHz, 35-GHz and 94-GHz have been largely unexploited. The purpose of this new focus group is to develop vertical velocity ARM products suitable for modelers. ARM response to their request has been slow. Most ARM instruments are suitable for cloud observations and have limited capabilities in precipitation Using ARM datasets for evaluating and improving cloud parameterization in global climate models (GCMs) is not straightforward, due to gigantic scale mismatches. Consider this... Looking only vertically drastically limits opportunities

30

ARM - Measurement - Vertical velocity  

NLE Websites -- All DOE Office Websites (Extended Search)

govMeasurementsVertical velocity govMeasurementsVertical velocity ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Measurement : Vertical velocity The component of the velocity vector, along the local vertical. Categories Atmospheric State Instruments The above measurement is considered scientifically relevant for the following instruments. Refer to the datastream (netcdf) file headers of each instrument for a list of all available measurements, including those recorded for diagnostic or quality assurance purposes. ARM Instruments CO2FLX : Carbon Dioxide Flux Measurement Systems ECOR : Eddy Correlation Flux Measurement System KAZR : Ka ARM Zenith Radar MMCR : Millimeter Wavelength Cloud Radar SODAR : Mini Sound Detection and Ranging

31

Cirrus Crystal Terminal Velocities  

Science Conference Proceedings (OSTI)

Cirrus crystal terminal velocities are of primary importance in determining the rate of transport of condensate from upper- to middle-tropospheric levels and profoundly influence the earths radiation balance through their effect on the rate of ...

Andrew J. Heymsfield; Jean Iaquinta

2000-04-01T23:59:59.000Z

32

Numerical Analysis of a Cold Air Distribution System  

E-Print Network (OSTI)

Cold air distribution systems may reduce the operating energy consumption of air-conditioned air supply system and improve the outside air volume percentages and indoor air quality. However, indoor temperature patterns and velocity field are easily non-uniform so that residents usually feel uncomfortable. The distribution of indoor airflow by cold air distribution is researched in this paper. We study indoor air distribution under different low temperature air supply conditions by numerical simulation. The simulated results agree well with the experiments.

Zhu, L.; Li, R.; Yuan, D.

2006-01-01T23:59:59.000Z

33

Building Energy Software Tools Directory: DD4M Air Duct Design  

NLE Websites -- All DOE Office Websites (Extended Search)

friction, constant velocity and or static regain procedures to design air ducts for air conditioning, heating, ventilation and materials handling. Allows 1000 duct sections...

34

Perspectives on Deposition Velocity  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Deposition Deposition Velocity ... Going down the rabbit hole to explain that sinking feeling Brian DiNunno, Ph.D. Project Enhancement Corporation June 6 th , 2012 Discussion Framework  Development of the HSS Deposition Velocity Safety Bulletin  Broader discussion of appropriate conservatism within dispersion modeling and DOE-STD-3009 DOE-STD-3009 Dose Comparison "General discussion is provided for source term calculation and dose estimation, as well as prescriptive guidance for the latter. The intent is that calculations be based on reasonably conservative estimates of the various input parameters." - DOE-STD-3009, Appendix A.3 DOE-STD-3009 Dispersion

35

Velocity pump reaction turbine  

DOE Patents (OSTI)

An expanding hydraulic/two-phase velocity pump reaction turbine including a dual concentric rotor configuration with an inter-rotor annular flow channel in which the inner rotor is mechanically driven by the outer rotor. In another embodiment, the inner rotor is immobilized and provided with gas recovery ports on its outer surface by means of which gas in solution may be recovered. This velocity pump reaction turbine configuration is capable of potential energy conversion efficiencies of up to 70%, and is particularly suited for geothermal applications.

House, Palmer A. (Walnut Creek, CA)

1982-01-01T23:59:59.000Z

36

Velocity pump reaction turbine  

DOE Patents (OSTI)

An expanding hydraulic/two-phase velocity pump reaction turbine including a dual concentric rotor configuration with an inter-rotor annular flow channel in which the inner rotor is mechanically driven by the outer rotor. In another embodiment, the inner rotor is immobilized and provided with gas recovery ports on its outer surface by means of which gas in solution may be recovered. This velocity pump reaction turbine configuration is capable of potential energy conversion efficiencies of up to 70%, and is particularly suited for geothermal applications.

House, Palmer A. (Walnut Creek, CA)

1984-01-01T23:59:59.000Z

37

Precipitation Identification from Radar Wind Profiler Spectral Moment Data: Vertical Velocity Histograms, Velocity Variance, and Signal PowerVertical Velocity Correlations  

Science Conference Proceedings (OSTI)

Correlations between range-corrected signal power Src and radial vertical velocity Vr, from the vertical beam of a UHF wind profiler can be used to distinguish between air- and precipitation-dominated echoes using an SrcVr correlation diagram. ...

F. Martin Ralph; Paul J. Neiman; Dominique Ruffieux

1996-06-01T23:59:59.000Z

38

Unitaxial constant velocity microactuator  

SciTech Connect

A uniaxial drive system or microactuator capable of operating in an ultra-high vacuum environment. The mechanism includes a flexible coupling having a bore therethrough, and two clamp/pusher assemblies mounted in axial ends of the coupling. The clamp/pusher assemblies are energized by voltage-operated piezoelectrics therewithin to operatively engage the shaft and coupling causing the shaft to move along its rotational axis through the bore. The microactuator is capable of repeatably positioning to sub-manometer accuracy while affording a scan range in excess of 5 centimeters. Moreover, the microactuator generates smooth, constant velocity motion profiles while producing a drive thrust of greater than 10 pounds. The system is remotely controlled and piezoelectrically driven, hence minimal thermal loading, vibrational excitation, or outgassing is introduced to the operating environment.

McIntyre, Timothy J. (Knoxville, TN)

1994-01-01T23:59:59.000Z

39

Characteristics of Vertical Velocity Cores in Different Convective Systems Observed over Gadanki, India  

Science Conference Proceedings (OSTI)

The Indian mesospherestratospheretroposphere (MST) radar measurements during the passage of 60 convective systems are used to study the vertical air velocity (w) characteristics of tropical convection. The up- and downdraft cores and various ...

K. N. Uma; T. Narayana Rao

2009-03-01T23:59:59.000Z

40

Is there Lower Limit to Velocity or Velocity Change?  

E-Print Network (OSTI)

Here we explore the possibility of a lower limit to velocity or velocity change which is 20 orders of magnitude smaller than the speed of light and explore the various observable signatures including those in cosmic rays and gamma ray bursts.

B. N. Sreenath; Kenath Arun; C. Sivaram

2012-09-17T23:59:59.000Z

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Air Quality  

NLE Websites -- All DOE Office Websites (Extended Search)

What We Monitor & Why » What We Monitor & Why » Air Quality Air Quality To preserve our existing wilderness-area air quality, LANL implements a conscientious program of air monitoring. April 12, 2012 Real-time data monitoring for particulate matter An air monitoring field team member tests one of LANL's tapered element oscillating microbalance samplers, which collects real-time particulate matter data. Contact Environmental Communication & Public Involvement P.O. Box 1663 MS M996 Los Alamos, NM 87545 (505) 667-0216 Email LANL monitors air quality 24 hours a day, 365 days a year. Why we monitor air LANL monitors many different pathways in order to assess their impact on workers, the public, animals, and plants. We monitor the air around the Laboratory to ensure our operations are not affecting the air of nearby

42

Measurement of adiabatic burning velocity in natural gas-like mixtures  

SciTech Connect

Experimental measurements of the adiabatic burning velocities were carried out for natural gas-like mixtures burning in air over a range of equivalence ratios at atmospheric pressure. Effect of CO{sub 2} dilution up to 60%, N{sub 2} dilution up to 40% and 25% enrichment of ethane on burning velocity of methane-air flames were studied. Heat flux method with setup similar to that of [K.J. Bosschaart, L.P.H. de Goey, Detailed analysis of the heat flux method for measuring burning velocity, Combustion and Flame 132 (2003) 170-180] was used for measurement of burning velocities. Initially experiments were done for methane-air and ethane-air mixtures at various equivalence ratios and the results were in good agreement with published data in the literature. Computations were performed using PREMIX code with GRI 3.0 reaction mechanism for all the mixtures. Predicted flame structures were used to the explain the effect of N{sub 2} and CO{sub 2} dilution on burning velocity of methane-air flames. Peak burning velocity for CH{sub 4}/CO{sub 2}-air mixtures occur near to {phi} = 1.0. (author)

Ratna Kishore, V.; Duhan, Nipun; Ravi, M.R.; Ray, Anjan [Department of Mechanical Engineering, Indian Institute of Technology, Delhi, Hauz Khas, New Delhi 110 016 (India)

2008-10-15T23:59:59.000Z

43

Ga Air Compressor, Ga Air Compressor Products, Ga Air ...  

U.S. Energy Information Administration (EIA)

Ga Air Compressor, You Can Buy Various High Quality Ga Air Compressor Products from Global Ga Air Compressor Suppliers and Ga Air Compressor ...

44

Particle Velocity and Deposition Efficiency in the Cold Spray Process  

SciTech Connect

Copper powder was sprayed by the cold-gas dynamic method. In-flight particle velocities were measured with a laser-two-focus system as a function of process parameters such as gas temperature, gas pressure, and powder feed rate. Particle velocities were uniform in a relatively large volume within the plume and agreed with theoretical predictions. The presence of the substrate was found to have no significant effect on particle velocities. Cold-spray deposition efficiencies were measured on aluminum substrates as a function of particle velocity and incident angle of the plume. Deposition efficiencies of up to 95% were achieved. The critical velocity for deposition was determined to be about 640 meters per second. This work investigates both the in-flight characteristics of copper particles in a supersonic cold-spray plume and the build-up of the subsequent coating on aluminum substrates. Velocities were found to be relatively constant within a large volume of the plume. Particle counts dropped off sharply away from the central axis. The presence of a substrate was found to have no effect on the velocity of the particles. A substantial mass-loading effect on the particle velocity was observed; particle velocities begin to drop as the mass ratio of powder to gas flow rates exceeds 3%. The measured variation of velocity with gas pressure and pre-heat temperature was in fairly good agreement with theoretical predictions. Helium may be used as the driving gas instead of air in order to achieve higher particle velocities for a given temperature and pressure. Coating deposition efficiencies were found to increase with particle velocity and decrease with gun- substrate angle. There did not appear to be any dependence of the deposition efficiency on coating thickness. A critical velocity for deposition of about 640 mk appears to fit the data well. The cold-spray technique shows promise as a method for the deposition of materials which are thermally sensitive or may experience rapid oxidation under typical thermal spray conditions. High deposition efficiencies are achievable for certain coating-substrate conditions. Work remains to determine the material and microstructural properties which govern the coating process.

Dykhuizen, R.C.; Gilmore, D.L.; Neiser, R.A.; Roemer, T.J.; Smith, M.F.

1998-11-12T23:59:59.000Z

45

ARM - Measurement - Hydrometeor fall velocity  

NLE Websites -- All DOE Office Websites (Extended Search)

fall velocity fall velocity ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Measurement : Hydrometeor fall velocity Fall velocity of hydrometeors (e.g. rain, snow, graupel, hail). Categories Cloud Properties Instruments The above measurement is considered scientifically relevant for the following instruments. Refer to the datastream (netcdf) file headers of each instrument for a list of all available measurements, including those recorded for diagnostic or quality assurance purposes. ARM Instruments DISDROMETER : Impact Disdrometer LDIS : Laser Disdrometer WSACR : Scanning ARM Cloud Radar, tuned to W-Band (95GHz) Field Campaign Instruments DISDROMETER : Impact Disdrometer PDI : Phase Doppler Interferometer

46

The Velocity-Selecting Cerenkov Counter  

E-Print Network (OSTI)

BAFFLE VELOCITY - SELECTING CERENKOV COUNTER (C 2) FiJI. 1velocity-selectinp: Cerenkov counter. ueaL-31;S CYLINDRICA~

Chamberlain, Owen; Weigand, Clyde

1956-01-01T23:59:59.000Z

47

Experimental Techniques for Measuring Temperature and Velocity...  

NLE Websites -- All DOE Office Websites (Extended Search)

Measuring Temperature and Velocity Fields to Improve the Use and Validation of Building Heat Transfer Models Title Experimental Techniques for Measuring Temperature and Velocity...

48

Hot Air Stratification of Ceiling Air Supply in a Large Space Building  

E-Print Network (OSTI)

The effects of different states of air supply and airflow patterns on temperature gradient distribution are calculated and analyzed with the help of FFSV3.0 software, using the LB models and LES and RANS methods. An experimental study with upper supply and upper return air flow was performed in normal airflow room. The results were compared with numerical simulation results and were found to agree well. Information on delaminating laws, and measurements of the relationship of delaminating heights and air supply temperature and velocity is also presented. According to the simulation results, a formula that avoids hot air delaminating in ceiling air supply is derived, which can guide engineering design.

Wang, H.; Wang, Z.; Liu, C.

2006-01-01T23:59:59.000Z

49

A Comparison of Techniques to Estimate Vertical Air Motions and Raindrop Size Distributions  

Science Conference Proceedings (OSTI)

Doppler velocity spectra collected at vertical incidence contain information on vertical air motions and drop-size distributions with high spatial and temporal resolution. In the past, the computational interdependence between vertical air ...

Karen L. Sangren; Peter S. Ray; Gene B. Walker

1984-06-01T23:59:59.000Z

50

Large-Eddy Simulation of Air Parcels in Stratocumulus Clouds: Time Scales and Spatial Variability  

Science Conference Proceedings (OSTI)

Large ensembles of air parcel trajectories driven by the (large-eddy simulation) LES-generated velocity fields from simulations of stratocumulus clouds were analyzed, focusing on statistics of air parcel in-cloud time scales, as well as their ...

Yefim L. Kogan

2006-03-01T23:59:59.000Z

51

Velocity Distributions from Nonextensive Thermodynamics  

E-Print Network (OSTI)

There is no accepted mechanism that explains the equilibrium structures that form in collisionless cosmological N-body simulations. Recent work has identified nonextensive thermodynamics as an innovative approach to the problem. The distribution function that results from adopting this framework has the same form as for polytropes, but the polytropic index is now related to the degree of nonextensiveness. In particular, the nonextensive approach can mimic the equilibrium structure of dark matter density profiles found in simulations. We extend the investigation of this approach to the velocity structures expected from nonextensive thermodynamics. We find that the nonextensive and simulated N-body rms-velocity distributions do not match one another. The nonextensive rms-velocity profile is either monotonically decreasing or displays little radial variation, each of which disagrees with the rms-velocity distributions seen in simulations. We conclude that the currently discussed nonextensive models require further modifications in order to corroborate dark matter halo simulations. (adapted from TeX)

Eric I. Barnes; Liliya L. R. Williams; Arif Babul; Julianne J. Dalcanton

2006-10-05T23:59:59.000Z

52

AirSea Gas Transfer: Mechanisms and Parameterization  

Science Conference Proceedings (OSTI)

The rate of airsea gas transfer has been largely parameterized on the basis of studies performed in laboratory tanks: empirical formulas are proposed for three wind-velocity regions. Observed features of the transfer in these regions are ...

Jin Wu

1996-08-01T23:59:59.000Z

53

ARM - PI Product - SGP and TWP (Manus) Ice Cloud Vertical Velocities  

NLE Websites -- All DOE Office Websites (Extended Search)

ProductsSGP and TWP (Manus) Ice Cloud Vertical ProductsSGP and TWP (Manus) Ice Cloud Vertical Velocities Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send PI Product : SGP and TWP (Manus) Ice Cloud Vertical Velocities 1997.01.01 - 2010.12.31 Site(s) SGP TWP General Description Daily netcdf-files of ice-cloud dynamics observed at the ARM sites at SGP (Jan1997-Dec2010) and Manus (Jul1999-Dec2010). The files include variables at different time resolution (10s, 20min, 1hr). Profiles of radar reflectivity factor (dbz), Doppler velocity (vel) as well as retrieved vertical air motion (V_air) and reflectivity-weighted particle terminal fall velocity (V_ter) are given at 10s, 20min and 1hr resolution. Lower level clouds are removed, however a multi-layer flag is included.

54

Air Resources: Prevention and Control of Air Contamination and Air  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Air Resources: Prevention and Control of Air Contamination and Air Air Resources: Prevention and Control of Air Contamination and Air Pollution, Air Quality Classifications and Standards, and Air Quality Area Classifications (New York) Air Resources: Prevention and Control of Air Contamination and Air Pollution, Air Quality Classifications and Standards, and Air Quality Area Classifications (New York) < Back Eligibility Agricultural Fuel Distributor Industrial Institutional Investor-Owned Utility Local Government Multi-Family Residential Municipal/Public Utility Nonprofit Rural Electric Cooperative Schools State/Provincial Govt Transportation Tribal Government Utility Program Info State New York Program Type Environmental Regulations Provider NY Department of Environmental Conservation These regulations establish emissions limits and permitting and operational

55

VELOCITY-FIELD MEASUREMENTS OF A SHOCK-ACCELERATED FLUID INSTABILITY  

Science Conference Proceedings (OSTI)

A cylinder of heavy gas (SF{sub 6}) in air is hit by a Mach 1.2 shock. The resultant Richtmyer-Meshkov instability is observed as it propagates through the test section of the shock tube. Six images are taken after shock impact, and the velocity field at one time is measured using Particle Image Velocimetry (PIV). The images of the density field show the development of a secondary instability in the cylinder. The velocity field provides us with information about the magnitudes of the velocities as well as the magnitude of the vorticity in the flow.

K. PRESTRIDGE; C. ZOLID; ET AL

2001-05-01T23:59:59.000Z

56

DOE Workshop - Deposition Velocity Status  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Delivering DOE's Vision for the Delivering DOE's Vision for the East Tennessee Technology Park Mission Safely Delivering the Department of Energy's Vision for the East Tennessee Technology Park Mission DOE Workshop Deposition Velocity Status Mike Hitchler, Manager Nuclear Facility Safety June 5, 2012 Safely Delivering DOE's Vision for the East Tennessee Technology Park Mission Existing UCOR Analyses * UCOR facilities at East Tennessee Technology Park (ETTP) and Oak Ridge National Laboratory (ORNL) use various plume models depending on when they were developed and by whom. - Some use MACCS or MACCS2 for dispersion evaluation. (~5 locations) - LLLW uses ingestion modeling (multiple locations)

57

Velocity Probability Density Functions for Oceanic Floats  

Science Conference Proceedings (OSTI)

Probability density functions (PDFs) of daily velocities from subsurface floats deployed in the North Atlantic and equatorial Atlantic Oceans are examined. In general, the PDFs are approximately Gaussian for small velocities, but with significant ...

Annalisa Bracco; J. H. LaCasce; Antonello Provenzale

2000-03-01T23:59:59.000Z

58

Equatorial Velocity Profiles. Part II: Zonal Component  

Science Conference Proceedings (OSTI)

Vertical profiles of horizontal velocity made along 53E in the western Indian Ocean, during and after he onset of the southwest monsoon in 1976, show features in zonal velocity of relatively small vertical scale. Persistence of the features over ...

Kathleen O'Neill; James R. Luyten

1984-12-01T23:59:59.000Z

59

Determining Vertical Water Velocities from Seaglider  

Science Conference Proceedings (OSTI)

Vertical velocities in the worlds oceans are typically small, less than 1 cm s?1, posing a significant challenge for observational techniques. Seaglider, an autonomous profiling instrument, can be used to estimate vertical water velocity in the ...

Eleanor Frajka-Williams; Charles C. Eriksen; Peter B. Rhines; Ramsey R. Harcourt

2011-12-01T23:59:59.000Z

60

Velocity Probability Density Functions from Altimetry  

Science Conference Proceedings (OSTI)

Probability density functions (pdfs) are employed to evaluate the distribution of velocities in the global ocean. This study computes pdfs of ocean surface velocity using altimetric data from the TOPEX/Poseidon satellite. Results show that the ...

Sarah T. Gille; Stefan G. Llewellyn Smith

2000-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Determining Velocities and Mixing Coefficients from Tracers  

Science Conference Proceedings (OSTI)

The effort to determine oceanic velocities from tracer distributions relies on a knowledge of the effects of mixing. However, the macroscopic diffusion coefficient, K, is generally not known and must be calculated along with the velocity. The ...

Jae Hak Lee; George Veronis

1989-04-01T23:59:59.000Z

62

An Acoustic Doppler and Electromagnetic Velocity Profiler  

Science Conference Proceedings (OSTI)

A freely failing current meter called the Absolute Velocity Profiler (AVP) is described. This profiler is an expansion of a previously developed instrument, the Electro-Magnetic Velocity Profiler (EMVP), with the additional capability of acoustic ...

Thomas B. Sanford; Robert G. Driver; John H. Dunlap

1985-06-01T23:59:59.000Z

63

Equatorial Velocity Profiles. Part I: Meridional Component  

Science Conference Proceedings (OSTI)

A time series or vertical profiles of horizontal velocity was collected in the western equatorial Indian Ocean during late spring of 1976. The meridional velocity component is examined here, the zonal component in Part II of this paper. The ...

Kathleen O'Neill

1984-12-01T23:59:59.000Z

64

Waterspout Velocity Measurements by Airborne Doppler Lidar  

Science Conference Proceedings (OSTI)

A Doppler lidar measures the line-of-sight velocity of cloud droplets in a waterspout much as a meteorological Doppler radar measures the velocity of larger hydrometeors. We discuss details of the application of an airborne Doppler lidar to ...

R. L. Schwiesow; R. E. Cupp; P. C. Sinclair; R. F. Abbey Jr.

1981-04-01T23:59:59.000Z

65

The effect of arc velocity on cold electrode erosion Alexei M. Essiptchouk,a)  

E-Print Network (OSTI)

of the radial redistribution of the gas due to centrifugal force in the vortex. Therefore the cold- est gas in air, for magnetic induction values B in the range of 0.005­0.386 T, axial air gas velocity of 7.65 ms displacement are used to diminish the erosion of the electrode: gas dynamic, i.e., application of vortex flow

Marotta, Aruy

66

Proceedings: Indoor Air 2005 OZONE REMOVAL BY RESIDENTIAL HVAC FILTERS  

E-Print Network (OSTI)

Proceedings: Indoor Air 2005 2366 OZONE REMOVAL BY RESIDENTIAL HVAC FILTERS P Zhao1,2 , JA Siegel1, Austin, Texas 78758, USA ABSTRACT HVAC filters have a significant influence on indoor air quality% for Filter #2 at a face velocity of 0.81 cm/s. The potential for HVAC filters to affect ozone concentrations

Siegel, Jeffrey

67

Measurements of Laminar Flame Velocity for Components of Natural Gas  

E-Print Network (OSTI)

This paper presents new experimental measurements of the laminar flame velocity of components of natural gas, methane, ethane, propane, and n?butane as well as of binary and tertiary mixtures of these compounds proposed as surrogates for natural gas. These measurements have been performed by the heat flux method using a newly built flat flame adiabatic burner at atmospheric pressure. The composition of the investigated air/hydrocarbon mixtures covers a wide range of equivalence ratios, from 0.6 to 2.1, for which it is possible to sufficiently stabilize the flame. Other measurements involving the enrichment of methane by hydrogen (up to 68%) and the enrichment of air by oxygen (oxycombustion techniques) were also performed. Both empirical correlations and a detailed chemical mechanism have been proposed, the predictions being satisfactorily compared with the newly obtained experimental data under a wide range of conditions.

Patricia Dirrenberger; Herv Le Gall; Roda Bounaceur; Olivier Herbinet; Re Glaude; Er Konnov

2013-01-01T23:59:59.000Z

68

Air Flow Distribution in the Sales Area of a Supermarket  

E-Print Network (OSTI)

Many kinds of goods are displayed in a supermarket, which have their own particularities. The consumer flow rate is great and the type of shelved goods varies significantly, thereby influencing the objects that generate heat, and the demands of air temperature, air velocity and humidity in different zones. The results of a study of a sales area of a supermarket in Harbin are presented in this paper, including air temperature, air velocity and humidity. According to the assessment index of air flow distribution (EDT, ADPI, temperature efficiency, energy coefficient of utilization, coefficient of ununiformity and so on), the experimental data were analyzed. The rationality of airflow distribution was then evaluated. Suggestions for air conditioning system design are also presented in this paper.

Fang, X.; Song, C.; Zhao, J.; Wang, Z.

2006-01-01T23:59:59.000Z

69

VELOCITY INDICATOR FOR EXTRUSION PRESS  

DOE Patents (OSTI)

An indicator is presented for measuring the lowspeed velocity of an object in one direction where the object returns in the opposite direction at a high speed. The indicator comprises a drum having its axis of rotation transverse to the linear movement of the object and a tape wound upon the drum with its free end extending therefrom and adapted to be connected to the object. A constant torque is applied to the drum in a direction to wind the tape on the drum. The speed of the tape in the unwinding direction is indicated on a tachometer which is coupled through a shaft and clutch means to the drum only when the tape is unwinding.

Digney, F.J. Jr.; Bevilacqua, F.

1959-04-01T23:59:59.000Z

70

Air cooled turbine component having an internal filtration system  

DOE Patents (OSTI)

A centrifugal particle separator is provided for removing particles such as microscopic dirt or dust particles from the compressed cooling air prior to reaching and cooling the turbine blades or turbine vanes of a turbine engine. The centrifugal particle separator structure has a substantially cylindrical body with an inlet arranged on a periphery of the substantially cylindrical body. Cooling air enters centrifugal particle separator through the separator inlet port having a linear velocity. When the cooling air impinges the substantially cylindrical body, the linear velocity is transformed into a rotational velocity, separating microscopic particles from the cooling air. Microscopic dust particles exit the centrifugal particle separator through a conical outlet and returned to a working medium.

Beeck, Alexander R. (Orlando, FL)

2012-05-15T23:59:59.000Z

71

Air Pollution (Illinois)  

Energy.gov (U.S. Department of Energy (DOE))

This article states regulations for monitoring air pollution, methods for permit applications, emission limitations for pollutants and air quality standards.

72

The velocity campaign for ignition on NIF  

SciTech Connect

Achieving inertial confinement fusion ignition requires a symmetric, high velocity implosion. Experiments show that we can reach 95 {+-} 5% of the required velocity by using a 420 TW, 1.6 MJ laser pulse. In addition, experiments with a depleted uranium hohlraum show an increase in capsule performance which suggests an additional 18 {+-} 5 {mu}m/ns of velocity with uranium hohlraums over gold hohlraums. Combining these two would give 99 {+-} 5% of the ignition velocity. Experiments show that we have the ability to tune symmetry using crossbeam transfer. We can control the second Legendre mode (P2) by changing the wavelength separation between the inner and outer cones of laser beams. We can control the azimuthal m = 4 asymmetry by changing the wavelength separation between the 23.5 and 30 degree beams on NIF. This paper describes our 'first pass' tuning the implosion velocity and shape on the National Ignition Facility laser [Moses et al., Phys. Plasmas, 16, 041006 (2009)].

Callahan, D. A.; Meezan, N. B.; Glenzer, S. H.; MacKinnon, A. J.; Benedetti, L. R.; Bradley, D. K.; Celeste, J. R.; Celliers, P. M.; Dixit, S. N.; Doeppner, T.; Dzentitis, E. G.; Glenn, S.; Haan, S. W.; Haynam, C. A.; Hicks, D. G.; Hinkel, D. E.; Jones, O. S.; Landen, O. L.; London, R. A.; MacPhee, A. G. [Lawrence Livermore National Laboratory, Livermore, California 94550 (United States); and others

2012-05-15T23:59:59.000Z

73

Impact Velocity (2011) | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Impact Velocity (2011) | National Nuclear Security Administration Impact Velocity (2011) | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Continuing Management Reform Countering Nuclear Terrorism About Us Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Media Room Congressional Testimony Fact Sheets Newsletters Press Releases Speeches Events Social Media Video Gallery Photo Gallery NNSA Archive Federal Employment Apply for Our Jobs Our Jobs Working at NNSA Blog Home > Media Room > Video Gallery > Impact Velocity (2011) Impact Velocity (2011) Impact Velocity (2011) From: NNSANews Views: 388 2 ratings Time: 02:26 More in Science & Technology See video Facebook Twitter

74

NREL Provides Guidance to Improve Air Mixing and Thermal Comfort in Homes (Fact Sheet)  

DOE Green Energy (OSTI)

NREL research determines optimal HVAC system design for proper air mixing and thermal comfort in homes. As U.S. homes become more energy efficient, heating, ventilation, and cooling (HVAC) systems will be downsized, and the air flow volumes required to meet heating and cooling loads may be too small to maintain uniform room air mixing-which can affect thermal comfort. Researchers at the National Renewable Energy Laboratory (NREL) evaluated the performance of high sidewall air supply inlets and confirmed that these systems can achieve good air mixing and provide suitable comfort levels for occupants. Using computational fluid dynamics modeling, NREL scientists tested the performance of high sidewall supply air jets over a wide range of parameters including supply air temperature, air velocity, and inlet size. This technique uses the model output to determine how well the supply air mixes with the room air. Thermal comfort is evaluated by monitoring air temperature and velocity in more than 600,000 control volumes that make up the occupied zone of a single room. The room has an acceptable comfort level when more than 70% of the control volumes meet the comfort criteria on both air temperature and velocity. The study shows that high sidewall supply air jets achieve uniform mixing in a room, which is essential for providing acceptable comfort levels. The study also provides information required to optimize overall space conditioning system design in both heating and cooling modes.

Not Available

2012-02-01T23:59:59.000Z

75

Air Leakage of Furnaces and Air Handlers  

NLE Websites -- All DOE Office Websites (Extended Search)

Air Leakage of Furnaces and Air Handlers Air Leakage of Furnaces and Air Handlers Title Air Leakage of Furnaces and Air Handlers Publication Type Journal Article LBNL Report Number LBNL-5553E Year of Publication 2010 Authors Walker, Iain S., Mile Lubliner, Darryl J. Dickerhoff, and William W. Delp Journal 2010 ACEEE Summer Study on Energy Efficiency in Buildings The Climate for efficiency is now Date Published 08/2010 Abstract In recent years, great strides have been made in reducing air leakage in residential and to a lesser extent small commercial forced air duct systems. Several authorities have introduced low leakage limits for thermal distribution systems; for example, the State of California Energy Code for Buildings gives credit for systems that leak less than 6% of the total air flow at 25 Pa.

76

Metal-Air Batteries  

Science Conference Proceedings (OSTI)

Metal-air batteries have much higher specific energies than most currently available primary and rechargeable batteries. Recent advances in electrode materials and electrolytes, as well as new designs on metal-air batteries, have attracted intensive effort in recent years, especially in the development of lithium-air batteries. The general principle in metal-air batteries will be reviewed in this chapter. The materials, preparation methods, and performances of metal-air batteries will be discussed. Two main metal-air batteries, Zn-air and Li-air batteries will be discussed in detail. Other type of metal-air batteries will also be described.

Zhang, Jiguang; Bruce, Peter G.; Zhang, Gregory

2011-08-01T23:59:59.000Z

77

Development and experimental evaluation of a high temperature mechanism for blended n-heptane-isooctane-ethanol-air-mixtures and gasoline-ethanol-air-mixtures  

Science Conference Proceedings (OSTI)

Laminar burning velocity measurements using the closed vessel bomb method have been done for fuel-blend-air-mixtures at 373 K initial temperature and up to 20 bar initial pressure. The two experimentally investigated fuel blends consist, on the one hand, ... Keywords: ethanol-gasoline-blends, laminar burning velocity

S. Jerzembeck; C. Glawe; N. Peters

2009-02-01T23:59:59.000Z

78

Chromospheric Doppler Velocity Oscillations in a Sunspot  

E-Print Network (OSTI)

We analyse the chromospheric Doppler velocity oscillations in a sunspot using the high resolution spectral observations obtained from the Fast Imaging Solar Spectrograph(FISS) of the New Solar Telescope at the Big Bear Solar Observatory. The Doppler velocity maps are constructed from the bisectors of the spectral observations. The time series analysis of Doppler velocity maps show enhanced power in the sunspot umbra at higher frequencies and in the penumbra at lower frequencies. We find that the peak power frequency decreases gradually from the umbra to outward.

Maurya, R A

2013-01-01T23:59:59.000Z

79

Demonstrations: collisions on an air track  

E-Print Network (OSTI)

Demonstrations: ·collisions on an air track Text: Fishbane 8-1, 8-2, 8-3, 8-4, 8-5, 8-6 Problems ) = d dt ( MTot Vcm ) = MTot dVcm dt = MTot acm Vcm = acm = dVcm dt cm velocity dRcm dt Thus, Rcm , Vcm , acm behave just like any kinematic set r, v, a, except that the dynamics is governed

Boal, David

80

Feasibility of air capture  

E-Print Network (OSTI)

Capturing CO2 from air, referred to as Air Capture, is being proposed as a viable climate change mitigation technology. The two major benefits of air capture, reported in literature, are that it allows us to reduce the ...

Ranjan, Manya

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Measuring Outdoor Air Intake Rates into Existing Building  

SciTech Connect

Practical and accurate technologies are needed for continuously measuring and controlling outdoor air (OA) intake rates in commercial building heating, ventilating, and air conditioning (HVAC) systems. This project evaluated two new measurement approaches. Laboratory experiments determined that OA flow rates were measurable with errors generally less than 10 percent using electronic air velocity probes installed between OA intake louver blades or at the outlet face of louvers. High accuracy was maintained with OA flow rates as low as 15 percent of the maximum for the louvers. Thus, with this measurement approach HVAC systems do not need separate OA intakes for minimum OA supply. System calibration parameters are required for each unique combination of louver type and velocity sensor location but calibrations are not necessary for each system installation. The research also determined that the accuracy of measuring OA flow rates with velocity probes located in the duct downstream of the intake louver was not improved by installing honeycomb airflow straighteners upstream of the probes. Errors varied with type of upstream louver, were as high as 100 percent, and were often greater than 25 percent. In conclusion, use of electronic air velocity probes between the blades of OA intake louvers or at the outlet face of louvers is a highly promising means of accurately measuring rates of OA flow into HVAC systems. The use of electronic velocity probes downstream of airflow straighteners is less promising, at least with the relatively small OA HVAC inlet systems employed in this research.

Fisk, William; Sullivan, Douglas; Cohen, Sebastian; Han, Hwataik

2009-04-16T23:59:59.000Z

82

Vertical Air Motion from T-REX Radiosonde and Dropsonde Data  

Science Conference Proceedings (OSTI)

The primary goal of this study is to explore the potential for estimating the vertical velocity (VV) of air from the surface to the stratosphere, using widely available radiosonde and dropsonde data. The rise and fall rates of radiosondes and ...

Junhong Wang; Jianchun Bian; William O. Brown; Harold Cole; Vanda Grubii?; Kate Young

2009-05-01T23:59:59.000Z

83

Primary zone air proportioner  

SciTech Connect

An air proportioner is provided for a liquid hydrocarbon fueled gas turbine of the type which is convertible to oil gas fuel and to coal gas fuel. The turbine includes a shell for enclosing the turbine, an air duct for venting air in said shell to a gasifier, and a fuel injector for injecting gasified fuel into the turbine. The air proportioner comprises a second air duct for venting air from the air duct for mixing with fuel from the gasifier. The air can be directly injected into the gas combustion basket along with the fuel from the injector or premixed with fuel from the gasifier prior to injection by the fuel injector.

Cleary, Edward N. G. (San Diego, CA)

1982-10-12T23:59:59.000Z

84

Air Pollution Control (Indiana)  

Energy.gov (U.S. Department of Energy (DOE))

This legislation establishes the Department of Environmental Management and the Air Pollution Control Board, which are tasked with the prevention, abatement, and control of air pollution by all...

85

Simulation of air and mist drilling for geothermal wells  

SciTech Connect

An improved method for calculating downhole temperatures, pressures, fluid densities and velocities during air drilling has been developed. The basic equations of fluid flow for a gas with cuttings and mist are presented along with a numerical method for their solution. Several applications of this calculational method are given, showing the effect of flow rate and standpipe pressures in typical air and mist drilling situations. 8 refs.

Mitchell, R.F.

1981-01-01T23:59:59.000Z

86

Estimating Spatial Velocity Statistics with Coherent Doppler Lidar  

Science Conference Proceedings (OSTI)

The spatial statistics of a simulated turbulent velocity field are estimated using radial velocity estimates from simulated coherent Doppler lidar data. The structure functions from the radial velocity estimates are processed to estimate the ...

Rod Frehlich; Larry Cornman

2002-03-01T23:59:59.000Z

87

Rotating heat pipe for air-conditioning  

SciTech Connect

A unique rotary hermetic heat pipe is disclosed for transferring heat from an external source to an external heat sink. The heat pipe has a tapered condensing surface which is curved preferably to provide uniform pumping acceleration, the heat pipe being rotated at a velocity such that the component of centrifugal acceleration in an axial direction parallel to the tapered surface is greater than lG and so that the condensing surface is kept relatively free of liquid at any attitude. The heat pipe may be incorporated in an air conditioning apparatus so that it projects through a small wall opening. In the preferred air conditioning apparatus, a hollow hermetic air impeller is provided which contains a liquefied gaseous refrigerant, such as freon, and means are provided for compressing the refrigerant in the evaporator region of the heat pipe.

Gray, V.H.

1976-12-28T23:59:59.000Z

88

Determination of the Rate of Dissipation of Turbulent Energy from Simultaneous Temperature and Velocity Shear Microstructure Measurements  

Science Conference Proceedings (OSTI)

Spectra of turbulence have been examined for both temperature gradient and velocity shear. The data for this comparison are 1015 m segments of vertical microstructure profiles (at depths of 5100 m) obtained during the 1978 Joint Air Sea ...

N. S. Oakey

1982-03-01T23:59:59.000Z

89

Impact of Hight Velocity Cold Spray Particles  

SciTech Connect

This paper presents experimental data and an computational model of the cold spray solid particle impact process. Copper particles impacting onto a polished stainless steel substrate are examined. The high velocity impact causes significant plastic deformation of both the particle and the sub- strate, but no melting is observed. The plastic deformation exposes clean surfaces that, under the high impact pressures, result in significant bond strengths between the particle and substrate. Experimental measurements of the splat and crater sizes compare well with the numerical calculations. It is shown that the crater depth is significant and increases with impact velocity. However, the splat diameter is much less sensitive to the impact velocity. It is also shown that the geometric lengths of the splat and crater scale linearly with the diameter of the impacting particle. It is hoped that the results presented will allow better understanding of the bonding process during cold spray.

Dykhuizen, R.C.; Gilmore, D.L.; Jiang, X.; Neiser, R.A.; Sampath, S.; Smith, M.F.

1998-12-01T23:59:59.000Z

90

Visibility graph analysis of solar wind velocity  

E-Print Network (OSTI)

We analyze in situ measurements of solar wind velocity obtained by Advanced Composition Explorer (ACE) spacecraft and Helios spacecraft during the years 1998-2012 and 1975-1983 respectively. The data belong to mainly solar cycle 23 (1996-2008) and solar cycle 21 (1976-1986) respectively. We use Directed Horizontal Visibility graph (DHVg) algorithm and estimate a graph functional, namely, the degree distance (D) as the Kullback-Leibler divergence (KLD) argument to understand time irreversibility of solar wind time series. We estimate this degree distance irreversibility parameter for these time series at different phases of solar activity cycle. Irreversibility parameter is first established for known dynamical data and then applied for solar wind velocity time series. It is observed that irreversibility in solar wind velocity fluctuations show similar behaviour at 0.3 AU (Helios data) and 1 AU (ACE data). Moreover it changes over the different phases of solar activity cycle.

Suyal, Vinita; Singh, Harinder P

2013-01-01T23:59:59.000Z

91

Energy Basics: Solar Air Heating  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

EERE: Energy Basics Solar Air Heating Solar air heating systems use air as the working fluid for absorbing and transferring solar energy. Solar air collectors (devices to heat air...

92

Isokinetic air sampler  

DOE Patents (OSTI)

An isokinetic air sampler includes a filter, a holder for the filter, an air pump for drawing air through the filter at a fixed, predetermined rate, an inlet assembly for the sampler having an inlet opening therein of a size such that isokinetic air sampling is obtained at a particular wind speed, a closure for the inlet opening and means for simultaneously opening the closure and turning on the air pump when the wind speed is such that isokinetic air sampling is obtained. A system incorporating a plurality of such samplers provided with air pumps set to draw air through the filter at the same fixed, predetermined rate and having different inlet opening sizes for use at different wind speeds is included within the ambit of the present invention as is a method of sampling air to measure airborne concentrations of particulate pollutants as a function of wind speed.

Sehmel, George A. (Richland, WA)

1979-01-01T23:59:59.000Z

93

Speed control with end cushion for high speed air cylinder  

DOE Patents (OSTI)

A high speed air cylinder in which the longitudinal movement of the piston within the air cylinder tube is controlled by pressurizing the air cylinder tube on the accelerating side of the piston and releasing pressure at a controlled rate on the decelerating side of the piston. The invention also includes a method for determining the pressure required on both the accelerating and decelerating sides of the piston to move the piston with a given load through a predetermined distance at the desired velocity, bringing the piston to rest safely without piston bounce at the end of its complete stroke. 4 figs.

Stevens, W.W.; Solbrig, C.W.

1989-06-20T23:59:59.000Z

94

Effect of temperature on wave velocities in sands and sandstones with heavy hydrocarbons  

SciTech Connect

A laboratory investigation was made of the effects of temperature on wave velocities in well cemented Massillon and Boise sandstones and unconsolidated Ottawa sand saturated with heavy hydrocarbons, as well as the dependence of compressional velocities in the hydrocarbons themselves as a function of temperature. The hydrocarbons selected as pore saturants were a commercial paraffin wax, 1-Eicosene, natural heavy crude, and natural tar. The experimental results show that the compressional wave velocities in the hydrocarbons decrease markedly with increasing temperature. In contrast wave velocities in the Massillon and Boise sandstones and unconsolidated Ottawa sand saturated with air or water decrease only little with increasing temperatures. The main reason for the large decreases in rocks with hydrocarbons is the melting of solid hydrocarbons, and high pore pressure. Thermal expansion of the saturants, and possibly thermal cracking of the heavy fractions and vaporization of the light fractions of the hydrocarbons may also contribute. The large decreases of the compressional and shear wave velocities in the hydrocarbon-saturated rocks and sands with temperature, suggest that seismic measurements such as used in seismology or borehole tomography may be very useful in detecting steam fronts in heavy hydrocarbon reservoirs undergoing steam flooding.

Wang, Z.; Nur, A.M.

1986-01-01T23:59:59.000Z

95

Vehicle Velocity Estimation Based on RSS Measurements  

Science Conference Proceedings (OSTI)

This paper presents a technique which is based on pattern recognition techniques, in order to estimate Mobile Terminal (MT) velocity. The proposed technique applies on received signal strength (RSS) measurements and more precisely on information extracted ... Keywords: HIDden Markov Model, WCDMA, clustering, location based services, pattern recognition, propagation modeling, traffic information

Theodore S. Stamoulakatos; Antonis S. Markopoulos; Miltiadis E. Anagnostou; Michalis E. Theologou

2007-03-01T23:59:59.000Z

96

Aggregate Terminal Velocity/Temperature Relations  

Science Conference Proceedings (OSTI)

Terminal velocities of snow aggregates in storms along the Front Range in eastern Colorado are examined with a ground-based two-dimensional video disdrometer. Power-law relationships for particles having equivalent volume diameters of 0.520 mm ...

Edward A. Brandes; Kyoko Ikeda; Gregory Thompson; Michael Schnhuber

2008-10-01T23:59:59.000Z

97

Study of the Influence of Air Supply Temperature on Air Distribution in the Run-through Large Space Architecture  

E-Print Network (OSTI)

The article introduces the concept and features of run-through large space. By using CFD technology, the paper simulates a velocity field and temperature field in the important air conditioned zone of China's science and technology museum (new museum) under winter operating conditions. At the same time, the indoor air flow regulations are summarized according to the simulation results. On the above basis, a new solution for airflow control of the connection in a run-through large space is put forward. The conclusion of this paper will offer guidance and reference for the air conditioning design of homogeneous architecture.

Tian, Z.; Zhang, J.; Zhu, M.; He, J.

2006-01-01T23:59:59.000Z

98

Vermont Air Pollution Control Regulations, Ambient Air Quality...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Ambient Air Quality Standards (Vermont) Vermont Air Pollution Control Regulations, Ambient Air Quality Standards (Vermont) Eligibility Utility Agricultural Investor-Owned Utility...

99

Vsd Oil Free Air Compressor, Vsd Oil Free Air Compressor ...  

U.S. Energy Information Administration (EIA)

Vsd Oil Free Air Compressor, You Can Buy Various High Quality Vsd Oil Free Air Compressor Products from Global Vsd Oil Free Air Compressor Suppliers ...

100

China Ga Air Compressor, China Ga Air Compressor Products ...  

U.S. Energy Information Administration (EIA)

China Ga Air Compressor, China Ga Air Compressor Suppliers and Manufacturers Directory - Source a Large Selection of Ga Air Compressor Products at ...

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Oil Free Vsd Air Compressor, Oil Free Vsd Air Compressor ...  

U.S. Energy Information Administration (EIA)

Oil Free Vsd Air Compressor, You Can Buy Various High Quality Oil Free Vsd Air Compressor Products from Global Oil Free Vsd Air Compressor Suppliers ...

102

Screw Type Ac Air Compressor Manufacturers, Screw Type Ac Air ...  

U.S. Energy Information Administration (EIA)

Screw Type Ac Air Compressor, Screw Type Ac Air Compressor Manufacturers & Suppliers Directory - Find here Screw Type Ac Air Compressor Traders, ...

103

Air Conditioning and lungs  

NLE Websites -- All DOE Office Websites (Extended Search)

Air Conditioning and lungs Name: freeman Status: NA Age: NA Location: NA Country: NA Date: Around 1993 Question: What affect does air conditioning have upon the lungs of the...

104

ARM - Evaluation Product - Vertical Air Motion during Large-Scale  

NLE Websites -- All DOE Office Websites (Extended Search)

ProductsVertical Air Motion during Large-Scale ProductsVertical Air Motion during Large-Scale Stratiform Rain Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Evaluation Product : Vertical Air Motion during Large-Scale Stratiform Rain Site(s) NIM SGP General Description The Vertical Air Motion during Large-Scale Stratiform Rain (VERVELSR) value-added product (VAP) uses the unique properties of a 95-GHz radar Doppler velocity spectra to produce vertical profiles of air motion during low-to-moderate (1-20 mm/hr) rainfall events It is designed to run at ARM sites that include a W-band ARM cloud radar (WACR) radar with spectra data processing. The VERVELSR VAP, based on the work of Giangrande et al. (2010), operates by exploiting a resonance effect that occurs in

105

On the theory of turbulent flame velocity  

E-Print Network (OSTI)

The renormalization ideas of self-similar dynamics of a strongly turbulent flame front are applied to the case of a flame with realistically large thermal expansion of the burning matter. In that case a flame front is corrugated both by external turbulence and the intrinsic flame instability. The analytical formulas for the velocity of flame propagation are obtained. It is demonstrated that the flame instability is of principal importance when the integral turbulent length scale is much larger than the cut off wavelength of the instability. The developed theory is used to analyse recent experiments on turbulent flames propagating in tubes. It is demonstrated that most of the flame velocity increase measured experimentally is provided by the large scale effects like the flame instability, and not by the small-scale external turbulence.

Vitaly Bychkov; Vyacheslav Akkerman; Arkady Petchenko

2012-10-19T23:59:59.000Z

106

Air Pollution- Local Air Quality (Ontario, Canada)  

Energy.gov (U.S. Department of Energy (DOE))

The Air Pollution regulation administered by the Ministry of the Environment enforces compliance to the standards set in the Ontario law. The law is phased in, with portions taking effect in 2010,...

107

Thin Air Breathing  

NLE Websites -- All DOE Office Websites (Extended Search)

Thin Air Breathing Thin Air Breathing Name: Amy Location: N/A Country: N/A Date: N/A Question: Why is it hard to breathe in thin air? What health dangers do mountain climbers face at high altitudes? Replies: Among the obvious dangers of losing ones footing, the oxygen available in the air is considerable less at higher altitudes. If I recall correctly, 21% of the atmosphere at standard temperature and pressure at sea level is composed of oxygen. This is less at higher altitudes. One can lose consciousness and even die in an oxygen deficient environment with changes from oxygen content to lower than 19.5%. This can unfortunate effect can occur within minutes. Dr. Myron The air is not really thin at high altitudes. The problem is that air pressure is lower. As altitude increases, air pressure decreases. In order for your lungs to fill with air, the air pressure in your lungs has to be less than the pressure of the air outside your lungs. Air moves from areas of higher pressure to lower pressure. As your diaphragm (the muscle that separates your chest cavity from your abdominal cavity) moves downward, the size of your chest cavity increases. This decreases the pressure in your chest and air flows in. When the diaphragm is up, it puts pressure on the chest cavity and the pressure in the lungs is greater than outside the lungs. Air flows out. This is an example of Boyle's Law. The movement of the diaphragm is controlled by the brainstem. Anyway-the reason that it is harder for some people to breathe at higher altitudes is that the air pressure differences aren't as great between the inside of the lungs and outside.

108

High-Velocity Rocks Final Report  

DOE Green Energy (OSTI)

The objective of our research was to develop and demonstrate seismic data-acquisition and data-processing technologies that allow geothermal prospects below high-velocity rock outcrops to be evaluated. To do this, we acquired a 3-component seismic test line across an area of exposed high-velocity rocks in Brewster County, Texas, where there is high heat flow and surface conditions mimic those found at numerous geothermal prospects. Seismic contractors have not succeeded in creating good-quality seismic data in this area for companies who have acquired data for oil and gas exploitation purposes. Our test profile traversed an area where high-velocity rocks and low-velocity sediment were exposed on the surface in alternating patterns that repeated along the test line. We verified that these surface conditions cause non-ending reverberations of Love waves, Rayleigh waves, and shallow critical refractions to travel across the earth surface between the boundaries of the fast-velocity and slow-velocity material exposed on the surface. These reverberating surface waves form the high level of noise in this area that does not allow reflections from deep interfaces to be seen and utilized. Our data-acquisition method of deploying a box array of closely spaced geophones allowed us to recognize and evaluate these surface-wave noise modes regardless of the azimuth direction to the surface anomaly that backscattered the waves and caused them to return to the test-line profile. With this knowledge of the surface-wave noise, we were able to process these test-line data to create P-P and SH-SH images that were superior to those produced by a skilled seismic data-processing contractor. Compared to the P-P data acquired along the test line, the SH-SH data provided a better detection of faults and could be used to trace these faults upward to the boundaries of exposed surface rocks. We expanded our comparison of the relative value of S-wave and P-wave seismic data for geothermal applications by inserting into this report a small part of the interpretation we have done with 3C3D data across Wister geothermal field in the Imperial Valley of California. This interpretation shows that P-SV data reveal faults (and by inference, also fractures) that cannot be easily, or confidently, seen with P-P data, and that the combination of P-P and P-SV data allows VP/VS velocity ratios to be estimated across a targeted reservoir interval to show where an interval has more sandstone (the preferred reservoir facies). The conclusion reached from this investigation is that S-wave seismic technology can be invaluable to geothermal operators. Thus we developed a strong interest in understanding the direct-S modes produced by vertical-force sources, particularly vertical vibrators, because if it can be demonstrated that direct-S modes produced by vertical-force sources can be used as effectively as the direct-S modes produced by horizontal-force sources, geothermal operators can acquire direct-S data across many more prospect areas than can be done with horizontal-force sources, which presently are limited to horizontal vibrators. We include some of our preliminary work in evaluating direct-S modes produced by vertical-force sources.

Hardage, Bob A; DeAngelo, Michael V; Ermolaeva, Elena; Hardage, Bob A; Remington, Randy; Sava, Diana; Wagner, Donald; Wei, Shuijion

2013-02-28T23:59:59.000Z

109

Measurements of the bulk and interfacial velocity profiles in oscillating Newtonian and Maxwellian fluids  

E-Print Network (OSTI)

We present the dynamic velocity profiles of a Newtonian fluid (glycerol) and a viscoelastic Maxwell fluid (CPyCl/NaSal in water) driven by an oscillating pressure gradient in a vertical cylindrical pipe. The frequency range explored has been chosen to include the first three resonance peaks of the dynamic permeability of the viscoelastic fluid / pipe system. Three different optical measurement techniques have been employed. Laser Doppler Anemometry has been used to measure the magnitude of the velocity at the centre of the liquid column. Particle Image Velocimetry and Optical Deflectometry are used to determine the velocity profiles at the bulk of the liquid column and at the liquid--air interface respectively. The velocity measurements in the bulk are in good agreement with the theoretical predictions of a linear theory. The results, however, show dramatic differences in the dynamic behaviour of Newtonian and viscoelastic fluids, and demonstrate the importance of resonance phenomena in viscoelastic fluid flows, biofluids in particular, in confined geometries.

M. Torralba; J. R. Castrejon-Pita; A. A. Castrejon-Pita; G. Huelsz; J. A. del Rio; J. Ortin

2005-05-10T23:59:59.000Z

110

Measurements of flatflame velocities of diethyl ether in air Fiona Gillespiea,b  

E-Print Network (OSTI)

is being drawn towards bioderived fuels, the most common of which is bioethanol. Bioethanol. %; however, bioethanol is produced primarily from food sources (corn, sugarcane, etc.) and its energy output to allow a sufficient flow of oxygen through the burner plate. Bronkhorst conversion coefficient factors

111

Unexplored Aspect of Velocity of light  

E-Print Network (OSTI)

In the post-Maxwellian era, sensing that the tide of discoveries in electromagnetim indicated a decline of the mechanical view, Einstein replaced Newton's three absolutes -- space, time and mass, with a single one, the velocity of light. The magnitude of the velocity of light was first determined and proven to be finite independently by Ole Romer and Bradley in the eighteenth century. In the nineteenth century, Fizeau carried out the first successful measurement of the speed of light using an earthbound apparatus. Thereafter, many earthbound experiments were conducted for its determination till 1983, when its magnitude was frozen at a fixed value after it was determined up to an accuracy level of a fraction of a meter per second. Einstein considered the speed of light derived from terrestrial experiments, to be the limiting speed of all natural phenomena. Einstein stated in connection with his general relativity theory that light rays could curve only when the velocity of propagation of light varies with position. Experiments have been conducted to prove the phenomenon of light deflection to higher and higher accuracy levels, but none so far to determine the speed of light at locations closer to the sun. To verify some essential aspects of general relativity, NASA had commendably planned many costly experiments. Hence, NASA can now be expected to expeditiously plan and execute the low cost experiment proposed here, so as to conclusively verify the effect of the solar gravitational field on the speed of light, as regards the important predictions of Einstein's theory of gravitation and of its remodeled form -- the Remodeled Relativity Theory, which retained and incorporated only experimentally proven concepts and principles.

Abhijit Biswas; Krishnan RS Mani

2008-05-13T23:59:59.000Z

112

Laser Doppler Velocimeter particle velocity measurement system  

DOE Green Energy (OSTI)

This report gives a detailed description of the operation of the Laser Doppler Velocimeter (LDV) system maintained by DIAL at MSU. LDV is used for the measurement of flow velocities and turbulence levels in various fluid flow settings. Ills report details the operation and maintenance of the LDV system and provides a first-time user with pertinent information regarding the system`s setup for a particular application. Particular attention has been given to the use of the Doppler signal analyzer (DSA) and the burst spectrum analyzer (BSA) signal processors and data analysis.

Wilson, W.W.; Srikantaiah, D.V.; Philip, T.; George, A.

1993-10-01T23:59:59.000Z

113

Radar Wind Profiler Radial Velocity: A Comparison with Doppler Lidar  

Science Conference Proceedings (OSTI)

The accuracy of the radial wind velocity measured with a radar wind profiler will depend on turbulent variability and instrumental noise. Radial velocity estimates of a boundary layer wind profiler are compared with those estimated by a Doppler ...

Stephen A. Cohn; R. Kent Goodrich

2002-12-01T23:59:59.000Z

114

Diagnosing Mesoscale Vertical Motion from Horizontal Velocity and Density Data  

Science Conference Proceedings (OSTI)

The mesoscale vertical velocity is obtained by solving a generalized omega equation (? equation) using density and horizontal velocity data from three consecutive quasi-synoptic high-resolution surveys in the Alboran Sea. The Atlantic Jet (AJ) ...

Enric Palls Sanz; lvaro Videz

2005-10-01T23:59:59.000Z

115

Terminal Velocity Adjustments for Plate-like Crystals and Graupel  

Science Conference Proceedings (OSTI)

Velocity adjustments are evaluated for altitude changes using Reynolds number-Davies number correlations of the form Re = aXb which have been obtained from empirical fall velocities of ice particles. In general, the altitude adjustment was found ...

Kenneth V. Beard; Andrew J. Heymsfield

1988-11-01T23:59:59.000Z

116

Indoor Air Quality Group  

Science Conference Proceedings (OSTI)

... CONTAM has been used at NIST to study the indoor air quality impacts of HVAC systems in single-family residential buildings, ventilation in large ...

2011-10-31T23:59:59.000Z

117

Air Resources Board  

E-Print Network (OSTI)

The Air Resources Board (the Board or ARB) will conduct a public hearing at the time and place noted below to consider amendments to the Verifkztion

unknown authors

2003-01-01T23:59:59.000Z

118

Air Resources Board  

E-Print Network (OSTI)

The Air Resources Board (the Board or ARB) will conduct a public hearing at the time and place noted below to consider amendments to the Verification

unknown authors

2003-01-01T23:59:59.000Z

119

Environmental Quality: Air (Louisiana)  

Energy.gov (U.S. Department of Energy (DOE))

The Department of Environmental Quality regulates air quality in Louisiana. The Department has an established a fee system for funding the monitoring, investigation and other activities required...

120

Air Pollution Project: Scenario  

NLE Websites -- All DOE Office Websites (Extended Search)

Project Summary HELP Index Summary Scenario Internet Links Student Pages SubjectContent Area: ScienceChemistry, Environment - Air Pollution Target Audience: High school chemistry...

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Forced air fireplace furnace  

Science Conference Proceedings (OSTI)

The design of heating system for buildings including a fireplace with an open front hearth for burning firewood, a chimney extending from the upper portion of the hearth, a metal firebox being open in the front and closed on the sides and back, a plenum chamber within and surrounding the sides and back of the metal firebox and the chimney lower portion, a horizontal heat distribution chamber positioned in the building attic and communicating at one end with the plenum chamber is described. An air distribution duct connects to the other end of the air distributing chamber, the duct extending to discharge heated air to a place in the building remote from the fireplace. A fan is placed in the horizontal air distributing chamber, and a return air duct extends from selected place in the building and communicates with the plenum chamber lower portion so that the fan draws air through the return air duct, through the plenum chamber around the firebox where the air is heated, through the horizontal distribution chamber, and out through the distribution duct for circulation of the heated air within the building.

Bruce, R.W.; Gorman, R.E.

1980-10-28T23:59:59.000Z

122

Movements in air conditioning.  

E-Print Network (OSTI)

??Movements in Air Conditioning is a collection of poems that explores the obstacles inherent in creating a new sense of home in a country that (more)

Hitt, Robert D. (Robert David)

2013-01-01T23:59:59.000Z

123

Adsorption air conditioner  

DOE Patents (OSTI)

A solar powered air conditioner using the adsorption process is constructed with its components in a nested cylindrical array for compactness and ease of operation.

Rousseau, Jean L. I. (Redondo Beach, CA)

1979-01-01T23:59:59.000Z

124

Room Air Conditioners  

NLE Websites -- All DOE Office Websites (Extended Search)

of Superefficient Room Air Conditioners year month keywords appliance energy efficiency energy efficiency incentives Market Transformation standards url https isswprod lbl gov...

125

Air Pollution Controls  

Energy.gov (U.S. Department of Energy (DOE))

Various statutes within the Wisconsin Legislative Documents relate to air pollution control. These statutes describe zoning, permitting, and emissions regulations for hazardous and non-hazardous...

126

LAMINAR BURNING VELOCITY OF GASOLINES WITH ADDITION OF ETHANOL  

E-Print Network (OSTI)

1 LAMINAR BURNING VELOCITY OF GASOLINES WITH ADDITION OF ETHANOL P. Dirrenberger1 , P.A. Glaude*1 (2014) 162-169" DOI : 10.1016/j.fuel.2013.07.015 #12;2 LAMINAR BURNING VELOCITY OF GASOLINES, Sweden Abstract The adiabatic laminar burning velocities of a commercial gasoline and of a model fuel (n

127

HALO VELOCITY GROUPS IN THE PISCES OVERDENSITY  

Science Conference Proceedings (OSTI)

We report spectroscopic observations of five faint (V {approx} 20) RR Lyrae stars associated with the Pisces overdensity conducted with the Gemini South Telescope. At a heliocentric and galactocentric distance of {approx}80 kpc, this is the most distant substructure in the Galactic halo known to date. We combined our observations with literature data and confirmed that the substructure is composed of two different kinematic groups. The main group contains eight stars and has (V{sub gsr}) = 50 km s{sup -1}, while the second group contains four stars at a velocity of (V{sub gsr}) = -52 km s{sup -1}, where V{sub gsr} is the radial velocity in the galactocentric standard of rest. The metallicity distribution of RR Lyrae stars in the Pisces overdensity is centered on [Fe/H] = -1.5 dex and has a width of 0.3 dex. The new data allowed us to establish that both groups are spatially extended making it very unlikely that they are bound systems, and are more likely to be debris of a tidally disrupted galaxy or galaxies. Due to small sky coverage, it is still unclear whether these groups have the same or different progenitors.

Sesar, Branimir; Ivezic, Zeljko [Department of Astronomy, University of Washington, P.O. Box 351580, Seattle, WA 98195-1580 (United States); Vivas, A. Katherina [Centro de Investigaciones de Astronomia (CIDA), Apartado Postal 264, Merida 5101-A (Venezuela, Bolivarian Republic of); Duffau, Sonia, E-mail: bsesar@u.washington.ed, E-mail: zi@u.washington.ed, E-mail: akvivas@cida.v, E-mail: sonia.duffau@gmail.co [Astronomisches Rechen-Institut, Zentrum fuer Astronomie der Universitaet Heidelberg, Moenchhofstrasse 12-14, D-69120 Heidelberg (Germany)

2010-07-01T23:59:59.000Z

128

Perturbations in high-velocity gas flow  

DOE Green Energy (OSTI)

High velocity explosive products or other low-density gases are often used to accelerate metal plates to high velocities. Perturbations in otherwise uniform flow configurations are sometimes sufficient to cause interactions that can rapidly destroy the integrity of the plates. In this study perturbations were introduced in uniform gas flows of detonated HE products and strongly shocked polyethylene, CH{sub 2}. The primary diagnostics were smear-camera records obtained when these gases impinged on layers of plexiglas separated by small argon-filled gaps. These records show shock-arrival times at various levels and thus determine not only the size of the perturbation but also its strength. Perturbations in HE gases running into H{sub 2} and in CH{sub 2} into H{sub 2} have been studied. Two-dimensional hydrodynamic calculations are in excellent agreement with the experiments, and enable one to study details of the flow not possible from experimental results. 1 ref., 5 figs.

Harvey, W.B.; McQueen, R.G. (Los Alamos National Lab., NM (USA))

1989-01-01T23:59:59.000Z

129

Aerodynamic effects on fuel spray characteristics: Air-assist atomizer  

SciTech Connect

Results are presented on the internal structure of a kerosene fuel spray, generated with an air-assist type nozzle. Effects of atomization air flow rate and combustion air swirl on droplet transport processes have been investigated. Spatially-resolved measurements have been obtained on mean droplet size, number density and velocity, at different combustion air swirl and atomization air flow rates. An ensemble light scattering technique, based on measurement of the polarization ratio, and laser velocimetry have been used for these measurements. The results indicate that as atomization air flow rate increases, the spray becomes confined to a narrower spray angle; in addition, mean droplet size decreases and number density increases significantly along the spray centerline. Larger droplets are found generally on the spray boundary, and smaller ones near the spray centerline. In all cases, there is a gradual increase in mean droplet size along the spray centerline with axial distance. Under burning conditions the flame plume becomes short and intense, with fewer droplets penetrating through the flame envelope. Combustion air swirl and atomization air have a significant effect on the transport of droplets and on combustion characteristics of spray flames. 20 refs., 9 figs.

Presser, C.; Semerjian, H.G.; Gupta, A.K.

1988-01-01T23:59:59.000Z

130

The Case of Sharp Velocity Transitions in High Vertical Wind Shear When Measuring Doppler Velocities with Narrow Nyquist Intervals  

Science Conference Proceedings (OSTI)

An investigation was launched following unexpected observations of step-function transitions in Doppler velocities from scanning radars in regions of high vertical wind shear. It revealed that, if wind velocity transitions are sufficiently sharp ...

Frdric Fabry; Clotilde Augros; Aldo Bellon

2013-03-01T23:59:59.000Z

131

Effects of Coaxial Air on Nitrogen-Diluted Hydrogen Jet Diffusion Flame Length and NOx Emission  

DOE Green Energy (OSTI)

Turbulent nitrogen-diluted hydrogen jet diffusion flames with high velocity coaxial air flows are investigated for their NOx emission levels. This study is motivated by the DOE turbine programs goal of achieving 2 ppm dry low NOx from turbine combustors running on nitrogen-diluted high-hydrogen fuels. In this study, effects of coaxial air velocity and momentum are varied while maintaining low overall equivalence ratios to eliminate the effects of recirculation of combustion products on flame lengths, flame temperatures, and resulting NOx emission levels. The nature of flame length and NOx emission scaling relationships are found to vary, depending on whether the combined fuel and coaxial air jet is fuel-rich or fuel-lean. In the absence of differential diffusion effects, flame lengths agree well with predicted trends, and NOx emissions levels are shown to decrease with increasing coaxial air velocity, as expected. Normalizing the NOx emission index with a flame residence time reveals some interesting trends, and indicates that a global flame strain based on the difference between the fuel and coaxial air velocities, as is traditionally used, is not a viable parameter for scaling the normalized NOx emissions of coaxial air jet diffusion flames.

Weiland, N.T.; Chen, R.-H.; Strakey, P.A.

2007-10-01T23:59:59.000Z

132

Force-velocity relations for multiple-molecular-motor transport  

E-Print Network (OSTI)

A transition rate model of cargo transport by $N$ molecular motors is proposed. Under the assumption of steady state, the force-velocity curve of multi-motor system can be derived from the force-velocity curve of single motor. Our work shows, in the case of low load, the velocity of multi-motor system can decrease or increase with increasing motor number, which is dependent on the single motor force-velocity curve. And most commonly, the velocity decreases. This gives a possible explanation to some recent

Ziqing Wang; Ming Li

2009-06-26T23:59:59.000Z

133

Evaluation of mixing downstream of tees in duct systems with respect to single point representative air sampling  

E-Print Network (OSTI)

Air duct systems in nuclear facilities must meet the requirements of ANSI N13.1-1999 and the Environmental Protection Agency (EPA) that the exhaust airflow be monitored with continuous sampling in case of an accidental release of airborne radionuclides. The continuous air sampling in a duct system is based on the concept of single point representative sampling at the sampling location where the velocity and contaminant profiles are nearly uniform. Sampling must be at a location where there is a uniform distribution via mixing in accordance with ANSI N13.1-1999. The purpose of this work is to identify the sampling locations where the velocity, momentum and contaminant concentrations fall below the 20% coefficient of variation (COV) requirements of ANSI N13.1-1999. Four sets of experiments were conducted on a generic 'T' mixing system. Measurements were made of the velocity, tracer gas concentration, ten micrometer particles and average flow swirl angle. The generic 'T' mixing system included three different combinations of sub duct sizes (6"x6", 9"x9" and 12"x12"), one main duct size (12"x12") and five air velocities (0, 100, 200, 300, and 400 fpm). An air blender was also introduced in some of the tests to promote mixing of the air streams from the main duct and sub duct. The experimental results suggested a turbulent mixing provided the accepted velocity COVs by 6 hydraulic diameters downstream. For similar velocity in the main duct and sub duct, an air blender provided the substantial improvement in 3 hydraulic diameters needed to achieve COVs below 10%. Without an air blender, the distance downstream of the T-junction for the COVs below 20% increased as the velocity of the sub duct airflow increased. About 95% of the cases achieved COVs below 10%. With the air blender, most of the cases with the air blender had the lower COVs than without the blender. However, at an area ratio (sub duct area / main duct area) of 0.25 and above a velocity ratio (velocity in the sub duct / velocity in the main duct) of 3, the air blender proved to be less beneficial for mixing. These results can apply to other duct systems with similar geometries and, ultimately, be a basis for selecting a proper sampling location under the requirements of the single point representative sampling.

Kim, Taehong

2003-01-01T23:59:59.000Z

134

Recirculating electric air filter  

DOE Patents (OSTI)

An electric air filter cartridge has a cylindrical inner high voltage eleode, a layer of filter material, and an outer ground electrode formed of a plurality of segments moveably connected together. The outer electrode can be easily opened to remove or insert filter material. Air flows through the two electrodes and the filter material and is exhausted from the center of the inner electrode.

Bergman, Werner (Pleasanton, CA)

1986-01-01T23:59:59.000Z

135

Portable oven air circulator  

DOE Patents (OSTI)

A portable air circulating apparatus for use in cooking ovens which is used to create air currents in the oven which transfer heat to cooking foodstuffs to promote more rapid and more uniform cooking or baking, the apparatus including a motor, fan blade and housing of metallic materials selected from a class of heat resistant materials.

Jorgensen, Jorgen A. (Bloomington, MN); Nygren, Donald W. (Minneapolis, MN)

1983-01-01T23:59:59.000Z

136

Meeting the Air Leakage  

NLE Websites -- All DOE Office Websites (Extended Search)

Meeting the Air Leakage Meeting the Air Leakage Requirements of the 2012 IECC The U.S. Department of Energy (DOE) recognizes the enormous potential that exists for improving the energy efficiency, safety and comfort of homes. The newest edition of the International Energy Conservation Code ® (IECC) (2012) sets the bar higher for energy efficiency, and new air sealing requirements are one of the key new provisions. This guide is a resource for understanding the new air leakage requirements in the 2012 IECC and suggestions on how these new measures can be met. It also provides information from Building America's Air Sealing Guide, Best Practices and case studies on homes that are currently meeting the provisions. The 2012 IECC and a few International Residential Code (IRC) requirements are referenced throughout the guide.

137

Abatement of Air Pollution: Prohibition of Air Pollution (Connecticut)  

Energy.gov (U.S. Department of Energy (DOE))

All air pollution not otherwise covered by these regulations is prohibited. Stationary sources which cause air pollution must be operated in accordance with all applicable emissions standards and...

138

Abatement of Air Pollution: Prohibition of Air Pollution (Connecticut...  

Open Energy Info (EERE)

DEEP Air Management Department Department of Energy and Environmental Protection Division Environmental Protection Division; Bureau of Air Management Address 79 Elm Street Place...

139

Air ejector augmented compressed air energy storage system  

DOE Patents (OSTI)

Energy is stored in slack demand periods by charging a plurality of underground reservoirs with air to the same peak storage pressure, during peak demand periods throttling the air from one storage reservoir into a gas turbine system at a constant inlet pressure until the air pressure in the reservoir falls to said constant inlet pressure, thereupon permitting air in a second reservoir to flow into said gas turbine system while drawing air from the first reservoir through a variable geometry air ejector and adjusting said variable geometry air ejector, said air flow being essentially at the constant inlet pressure of the gas turbine system.

Ahrens, Frederick W. (Naperville, IL); Kartsounes, George T. (Naperville, IL)

1980-01-01T23:59:59.000Z

140

Feature - Lithium-air Batteries  

NLE Websites -- All DOE Office Websites (Extended Search)

Develop Lithium-Air Battery Li-air Li-air batteries hold the promise of increasing the energy density of Li-ion batteries by as much as five to 10 times. But that potential will...

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Air Shower Simulations  

SciTech Connect

Air shower simulations are a vital part of the design of air shower experiments and the analysis of their data. We describe the basic features of air showers and explain why numerical simulations are the appropriate approach to model the shower simulation. The CORSIKA program, the standard simulation program in this field, is introduced and its features, performance and limitations are discussed. The basic principles of hadronic interaction models and some gerneral simulation techniques are explained. Also a brief introduction to the installation and use of CORSIKA is given.

Alania, Marco; Gomez, Adolfo V. Chamorro [Centro de Tecnologias de Informacion y Comunicaciones, Universidad Nacional de Ingenieria, Lima (Peru); Araya, Ignacio J. [Departamento de Astronomia y Astrofisica, Pontificia Universidad Catolica de Chile, Av. Vicuna Mackenna 4860, Santiago (Chile); Huerta, Humberto Martinez; Flores, Alejandra Parra [Facultad de Ciencias Fisico Matematicas, Benemerita Universidad Autonoma de Puebla, Puebla (Mexico); Knapp, Johannes [School of Physics and Astronomy, University of Leeds, Leeds LS2 9JT (United Kingdom)

2009-04-30T23:59:59.000Z

142

Air heating system  

DOE Patents (OSTI)

A self-starting, fuel-fired, air heating system including a vapor generator, a turbine, and a condenser connected in a closed circuit such that the vapor output from the vapor generator is conducted to the turbine and then to the condenser where it is condensed for return to the vapor generator. The turbine drives an air blower which passes air over the condenser for cooling the condenser. Also, a condensate pump is driven by the turbine. The disclosure is particularly concerned with the provision of heat exchanger and circuitry for cooling the condensed fluid output from the pump prior to its return to the vapor generator.

Primeau, John J. (19800 Seminole Rd., Euclid, OH 44117)

1983-03-01T23:59:59.000Z

143

Air Handling Unit Supply Air Temperature Optimization During Economizer Cycles  

E-Print Network (OSTI)

Most air handling units (AHUs) in commercial buildings have an air economizer cycle for free cooling under certain outside air conditions. During the economizer cycle, the outside air and return air dampers are modulated to seek mixing air temperature at supply air temperature setpoint. Mechanical cooling is always required when outside air temperature is higher than the supply air temperature setpoint. Generally the supply air temperature setpoint is set at 55F for space humidity control. Actually the dehumidification is not necessary when outside air dew point is less than 55F. Meanwhile the space may have less cooling load due to envelope heat loss and/or occupant schedule. These provide an opportunity to use higher supply air temperature to reduce or eliminate mechanical cooling and terminal box reheat. On the other hand the higher supply air temperature will require higher air flow as well as higher fan power. Therefore the supply air temperature has to be optimized to minimize the combined energy for fan, cooling and heating energy. In this paper a simple energy consumption model is established for AHU systems during the economizer and then a optimal supply air temperature control is developed to minimize the total cost of the mechanical cooling and the fan motor power. This paper presents AHU system energy modeling, supply air temperature optimization, and simulated energy savings.

Xu, K.; Liu, M.; Wang, G.; Wang, Z.

2007-01-01T23:59:59.000Z

144

Air Quality | Open Energy Information  

Open Energy Info (EERE)

Air Quality Jump to: navigation, search Retrieved from "http:en.openei.orgwindex.php?titleAirQuality&oldid612070" Category: NEPA Resources...

145

Air Carrier Flight Operations  

E-Print Network (OSTI)

Most air carriers operate under a system of prioritized goals including safety, customer service (on-time departures and arrivals) and operating economics. The flight operations department is responsible for the safe and ...

Midkif, Alan H.

146

AIR RESOURCES BOARD Acknowledgements  

E-Print Network (OSTI)

This report was prepared with the assistance and support from other agencies, divisions and offices of the Air Resources Board, and private firms. Staff would especially like to thank the following individuals for their assistance in developing this proposed pathway:

Green Wastes; Green Wastes; Richard Corey; Deputy Executive Officer; Cynthia Marvin Chief; Michael Waugh Chief; Kamal Ahuja; Brian Helmowski; Wes Ingram; Ray Asregadoo (arb; Juliet Bohn (hwma; Richard Boyd (arb; Alicia Chakrabarthy (ebmud; Steven Cliff (arb; Kevin Dickison (ebmud; Jacques Franco (calrecycle

2012-01-01T23:59:59.000Z

147

Breathing zone air sampler  

DOE Patents (OSTI)

A sampling apparatus is provided which comprises a sampler for sampling air in the breathing zone of a wearer of the apparatus and a support for the sampler preferably in the form of a pair of eyeglasses. The sampler comprises a sampling assembly supported on the frame of the eyeglasses and including a pair of sample transport tubes which are suspended, in use, centrally of the frame so as to be disposed on opposite sides of the nose of the wearer and which each include an inlet therein that, in use, is disposed adjacent to a respective nostril of the nose of the wearer. A filter holder connected to sample transport tubes supports a removable filter for filtering out particulate material in the air sampled by the apparatus. The sample apparatus is connected to a pump for drawing air into the apparatus through the tube inlets so that the air passes through the filter.

Tobin, John (Bethel Park, PA)

1989-01-01T23:59:59.000Z

148

air_water.cdr  

Office of Legacy Management (LM)

Office of Legacy Management Weldon Spring Site Air and Water Monitoring 32008 This fact sheet provides information at Weldon Spring, Missouri. This site is managed by the U.S....

149

FREE AIR PRESSURE MEASUREMENTS  

SciTech Connect

Indenter gages, Wiancko gages, and interferometer gages were used to measure air overpressure vs time at essentially ground level stations for both the surface (S) and undprground (U) atomic explosions. For the S Burst several instruments were placed on a line extending from an overpressure region of 13 psi to a region of less than one psi. The air measurements for the U Burst ranged from 32 to 2 psi. (D. L.G.)

Howard, W.J.; Jones, R.D.

1952-02-19T23:59:59.000Z

150

Standardization of the cumulative absolute velocity  

SciTech Connect

EPRI NP-5930, A Criterion for Determining Exceedance of the Operating Basis Earthquake,'' was published in July 1988. As defined in that report, the Operating Basis Earthquake (OBE) is exceeded when both a response spectrum parameter and a second damage parameter, referred to as the Cumulative Absolute Velocity (CAV), are exceeded. In the review process of the above report, it was noted that the calculation of CAV could be confounded by time history records of long duration containing low (nondamaging) acceleration. Therefore, it is necessary to standardize the method of calculating CAV to account for record length. This standardized methodology allows consistent comparisons between future CAV calculations and the adjusted CAV threshold value based upon applying the standardized methodology to the data set presented in EPRI NP-5930. The recommended method to standardize the CAV calculation is to window its calculation on a second-by-second basis for a given time history. If the absolute acceleration exceeds 0.025g at any time during each one second interval, the earthquake records used in EPRI NP-5930 have been reanalyzed and the adjusted threshold of damage for CAV was found to be 0.16g-set.

O'Hara, T.F.; Jacobson, J.P. (Yankee Atomic Electric Co., Bolton, MA (United States))

1991-12-01T23:59:59.000Z

151

Out-of-plane ultrasonic velocity measurement  

DOE Patents (OSTI)

A method for improving the accuracy of measuring the velocity and time of flight of ultrasonic signals through moving web-like materials such as paper, paperboard and the like, includes a pair of ultrasonic transducers disposed on opposing sides of a moving web-like material. In order to provide acoustical coupling between the transducers and the web-like material, the transducers are disposed in fluid-filled wheels. Errors due to variances in the wheel thicknesses about their circumference which can affect time of flight measurements and ultimately the mechanical property being tested are compensated by averaging the ultrasonic signals for a predetermined number of revolutions. The invention further includes a method for compensating for errors resulting from the digitization of the ultrasonic signals. More particularly, the invention includes a method for eliminating errors known as trigger jitter inherent with digitizing oscilloscopes used to digitize the signals for manipulation by a digital computer. In particular, rather than cross-correlate ultrasonic signals taken during different sample periods as is known in the art in order to determine the time of flight of the ultrasonic signal through the moving web, a pulse echo box is provided to enable cross-correlation of predetermined transmitted ultrasonic signals with predetermined reflected ultrasonic or echo signals during the sample period. By cross-correlating ultrasonic signals in the same sample period, the error associated with trigger jitter is eliminated.

Hall, Maclin S. (Marietta, GA); Brodeur, Pierre H. (Smyrna, GA); Jackson, Theodore G. (Atlanta, GA)

1998-01-01T23:59:59.000Z

152

Out-of-plane ultrasonic velocity measurement  

DOE Patents (OSTI)

A method for improving the accuracy of measuring the velocity and time of flight of ultrasonic signals through moving web-like materials such as paper, paperboard and the like, includes a pair of ultrasonic transducers disposed on opposing sides of a moving web-like material. In order to provide acoustical coupling between the transducers and the web-like material, the transducers are disposed in fluid-filled wheels. Errors due to variances in the wheel thicknesses about their circumference which can affect time of flight measurements and ultimately the mechanical property being tested are compensated by averaging the ultrasonic signals for a predetermined number of revolutions. The invention further includes a method for compensating for errors resulting from the digitization of the ultrasonic signals. More particularly, the invention includes a method for eliminating errors known as trigger jitter inherent with digitizing oscilloscopes used to digitize the signals for manipulation by a digital computer. In particular, rather than cross-correlate ultrasonic signals taken during different sample periods as is known in the art in order to determine the time of flight of the ultrasonic signal through the moving web, a pulse echo box is provided to enable cross-correlation of predetermined transmitted ultrasonic signals with predetermined reflected ultrasonic or echo signals during the sample period. By cross-correlating ultrasonic signals in the same sample period, the error associated with trigger jitter is eliminated. 20 figs.

Hall, M.S.; Brodeur, P.H.; Jackson, T.G.

1998-07-14T23:59:59.000Z

153

Air Cooling | Open Energy Information  

Open Energy Info (EERE)

Cooling Cooling Jump to: navigation, search Dictionary.png Air Cooling: Air cooling is commonly defined as rejecting heat from an object by flowing air over the surface of the object, through means of convection. Air cooling requires that the air must be cooler than the object or surface from which it is expected to remove heat. This is due to the second law of thermodynamics, which states that heat will only move spontaneously from a hot reservoir (the heat sink) to a cold reservoir (the air). Other definitions:Wikipedia Reegle Air Cooling Air Cooling Diagram of Air Cooled Condenser designed by GEA Heat Exchangers Ltd. (http://www.gea-btt.com.cn/opencms/opencms/bttc/en/Products/Air_Cooled_Condenser.html) Air cooling is limited on ambient temperatures and typically require a

154

Modified definition of group velocity and electromagnetic energy conservation equation  

E-Print Network (OSTI)

The classical definition of group velocity has two flaws: (a) the group velocity can be greater than the phase velocity in a non-dispersive medium; (b) the definition is not consistent with the principle of relativity. To remove the flaws, a modified definition is proposed. A criterion is set up to identify the justification of group velocity definition. A "superluminal power flow" is constructed to show that the electromagnetic energy conservation equation cannot uniquely define the power flow if the principle of Fermat is not taken into account.

Changbiao Wang

2013-06-13T23:59:59.000Z

155

New Insights Into Deep Convective Core Vertical Velocities Using...  

NLE Websites -- All DOE Office Websites (Extended Search)

Insights Into Deep Convective Core Vertical Velocities Using ARM UHF Wind Profilers For original submission and image(s), see ARM Research Highlights http:www.arm.govscience...

156

Temporal Velocity Variations beneath the Coso Geothermal Field...  

Open Energy Info (EERE)

events and determine the compressional and shear wave velocity as well as their ratio. In a first step, we apply traveltime tomography based on the observed microearthquake...

157

P wave velocity variations in the Coso region, California, derived...  

Open Energy Info (EERE)

P wave velocity variations in the Coso region, California, derived from local earthquake travel times Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal...

158

InAir: sharing indoor air quality measurements and visualizations  

Science Conference Proceedings (OSTI)

This paper describes inAir, a tool for sharing measurements and visualizations of indoor air quality within one's social network. Poor indoor air quality is difficult for humans to detect through sight and smell alone and can contribute to the development ... Keywords: air quality, domestic technology, environment, health, iphone, persuasive technology, sensors, sustainability

Sunyoung Kim; Eric Paulos

2010-04-01T23:59:59.000Z

159

Analytical modeling of a hydraulically-compensated compressed-air energy-storage system  

Science Conference Proceedings (OSTI)

A computer program was developed to calculate the dynamic response of a hydraulically-compensated compressed air energy storage (CAES) system, including the compressor, air pipe, cavern, and hydraulic compensation pipe. The model is theoretically based on the two-fluid model in which the dynamics of each phase are presented by its set of conservation equations for mass and momentum. The conservation equations define the space and time distribution of pressure, void fraction, air saturation, and phase velocities. The phases are coupled by two interface equations. The first defines the rate of generation (or dissolution) of gaseous air in water and can include the effects of supersaturation. The second defines the frictional shear coupling (drag) between the gaseous air and water as they move relative to each other. The relative motion of the air and water is, therefore, calculated and not specified by a slip or drift-velocity correlation. The total CASE system is represented by a nodal arrangement. The conservation equations are written for each nodal volume and are solved numerically. System boundary conditions include the air flow rate, atmospheric pressure at the top of the compensation pipe, and air saturation in the reservoir. Initial conditions are selected for velocity and air saturation. Uniform and constant temperature (60/sup 0/F) is assumed. The analytical model was used to investigate the dynamic response of a proposed system.Investigative calculations considered high and low water levels, and a variety of charging and operating conditions. For all cases investigated, the cavern response to air-charging, was a damped oscillation of pressure and flow. Detailed results are presented. These calculations indicate that the Champagne Effect is unlikely to cause blowout for a properly designed CAES system.

McMonagle, C.A.; Rowe, D.S.

1982-12-01T23:59:59.000Z

160

Simulation of air and mist drilling for geothermal wells  

SciTech Connect

An air drilling model has been developed that accounts for cuttings and mist. Comparison of the model results with previous work shows this model to be more conservative. The equations developed are simple enough to be used in hand calculations, but the full capability of the model is more easily obtained with a computer program. Studies with the model show that volume requirements and standpipe pressures are significantly different for mist drilling compared with air drilling. An improved method for calculating downhole temperatures, pressures, fluid densities, and velocities during air drilling has been developed. Improvements on previous methods include the following. A fully transient thermal analysis of the wellbore and formation is used to determine the flowing temperatures. The effects of flow acceleration are included explicitly in the calculation. The slip velocity between the gas and the cuttings is determined by the use of a separate momentum equation for the cuttings. The possibility of critical flow in the wellbore is tested and appropriate changes in the volume flow rate and standpipe pressure are made automatically. The standpipe and flowing pressures are predicted. The analysis is conservative. The effect of the cuttings on the wellbore flow will tend to overpredict the required volume flow rates. In this paper, the basic equations of fluid flow for a gas with cuttings and mist are presented along with a numerical method for their solution. Several applications of this calculational method are given, showing the effect of flow rate and standpipe pressure in typical air and mist drilling situations.

Mitchell, R.F.

1983-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Predictions of thermal comfort and pollutant distributions for a thermostatically-controlled, air-conditioned, partitioned room: Numerical results and enhanced graphical presentation  

SciTech Connect

An index of local thermal comfort and pollutant distributions have been computed with the TEMPEST computer code, in a transient simulation of an air-conditioned enclosure with an incomplete partition. This complex three-dimensional air conditioning problem included forced ventilation through inlet veins, flow through a partition, remote return air vents, and infiltration source, a pollutant source, and a thermostatically controlled air conditioning system. Five forced ventilation schemes that varied in vent areas and face velocities were simulated. Thermal comfort was modeled as a three-dimensional scalar field dependent on the fluid velocity and temperature fields; where humidity activity levels, and clothing were considered constants. Pollutants transport was incorporated through an additional constituent diffusion equation. Six distinct graphic techniques for the visualization of the three-dimensional data fields of air velocity, temperature, and comfort index were tested. 4 refs., 7 figs., 1 tab.

White, M.D.; Eyler, L.L.

1989-05-01T23:59:59.000Z

162

Compressed Air System Maintenance Guide  

Science Conference Proceedings (OSTI)

The "Compressed Air System Maintenance Guide" provides fossil plant personnel with information on the operation and maintenance of the compressed air system. The contents of this guide will assist personnel in improving performance of the compressed air system, reducing maintenance costs, and increasing air system reliability.

2002-11-27T23:59:59.000Z

163

Solar Buildings: Transpired Air Collectors  

DOE Green Energy (OSTI)

Transpired air collectors preheat building ventilation air by using the building's ventilation fan to draw fresh air through the system. The intake air is heated as it passes through the perforated absorber plate and up the plenum between the absorber and the south wall of the building. Reduced heating costs will pay for the systems in 3--12 years.

NONE

1998-11-24T23:59:59.000Z

164

Modeling of a Signal Processing System for Aircraft Air Data  

NLE Websites -- All DOE Office Websites (Extended Search)

Modeling of a Signal Processing System for Aircraft Air Data Modeling of a Signal Processing System for Aircraft Air Data Instrumentation Speaker(s): Thomas John Rohloff Date: September 21, 1998 - 12:00pm Location: 90-3148 Seminar Host/Point of Contact: Joan M. Daisey The velocity, attitude and altitude of flight vehicles have typically been measured with booms that extend from the vehicle surface out into the flow field. However, this arrangement was found to be unacceptable for certain flight applications. Instrumentation was therefore developed by other researchers to measure the flight parameters using an array of pressure measurements located on the surface of the vehicle. The relationship between these pressure measurements and the air data is a complex non-linear function that is not easily described with simple aerodynamic

165

Inverter Controlled Screw Air Compressor Manufacturers ...  

U.S. Energy Information Administration (EIA)

Inverter Controlled Screw Air Compressor, Inverter Controlled Screw Air Compressor Manufacturers & Suppliers Directory - Find here Inverter ...

166

Measurements of Laminar Flame Velocity for Components of Natural Gas  

E-Print Network (OSTI)

Measurements of Laminar Flame Velocity for Components of Natural Gas Patricia Dirrenberger1 flame velocity of components of natural gas, methane, ethane, propane, and nbutane as well as of binary and tertiary mixtures of these compounds proposed as surrogates for natural gas. These measurements have been

167

Compressed air energy storage system  

DOE Patents (OSTI)

An internal combustion reciprocating engine is operable as a compressor during slack demand periods utilizing excess power from a power grid to charge air into an air storage reservoir and as an expander during peak demand periods to feed power into the power grid utilizing air obtained from the air storage reservoir together with combustible fuel. Preferably the internal combustion reciprocating engine is operated at high pressure and a low pressure turbine and compressor are also employed for air compression and power generation.

Ahrens, Frederick W. (Naperville, IL); Kartsounes, George T. (Naperville, IL)

1981-01-01T23:59:59.000Z

168

air_water.cdr  

Office of Legacy Management (LM)

12/2011 12/2011 Air Monitoring Groundwater Monitoring Surface Water Monitoring A continuously operating air monitoring network was in place from 1986 through 2000 for the Weldon Spring Site Remedial Action Project (WSSRAP) to measure levels of gamma radiation, radioactive dust particles, radon gas, and asbestos. With remediation of contaminated materials essentially complete and measurements indistinguishable from background, the U.S. Department of Energy (DOE) ceased perimeter and offsite air monitoring as of December 31, 2000. Groundwater has been routinely monitored at the site since 1986. Separate groundwater monitoring programs were established for the Chemical Plant and Quarry sites because of geographic separation and differences in the hydrogeologic features that influence

169

Air Charter Services  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

42.2 (April 2012) 42.2 (April 2012) 1 Documentation and Approval of Federally Funded International Travel (Fly America Act-Open Skies Agreement) Overview This section provides guidance to DOE Contracting Officers, Contracting Officer Representatives, and Program Officials on documentation and approval of federally funded international travel by Federal contractors and subcontractors in accordance with FAR 52.247-63 PREFERENCE FOR U.S.-FLAG AIR CARRIERS (JUNE 2003), 49 U.S.C. §40118 (Fly America Act) and the Open Skies Agreements as amended. Background Contracts that include FAR clause 52.247-63, PREFERENCE FOR U.S.-FLAG AIR CARRIERS (JUNE 2003) as prescribed in FAR 47.405 require that, if available, the Contractor (and subcontractors), in performing work under the contract, shall use U.S.-flag air carriers for

170

AIR COOLED NEUTRONIC REACTOR  

DOE Patents (OSTI)

A nuclear reactor of the air-cooled, graphite moderated type is described. The active core consists of a cubicle mass of graphite, approximately 25 feet in each dimension, having horizontal channels of square cross section extending between two of the opposite faces, a plurality of cylindrical uranium slugs disposed in end to end abutting relationship within said channels providing a space in the channels through which air may be circulated, and a cadmium control rod extending within a channel provided in the moderator. Suitable shielding is provlded around the core, as are also provided a fuel element loading and discharge means, and a means to circulate air through the coolant channels through the fuel charels to cool the reactor.

Fermi, E.; Szilard, L.

1958-05-27T23:59:59.000Z

171

Multiple mapping conditioning of velocity in turbulent jet flames  

Science Conference Proceedings (OSTI)

Multiple mapping conditioning (MMC) has emerged as a new approach to model turbulent reacting flows. This study revises the standard MMC closure for velocity in turbulent jet flows from linearity in the reference space to linearity in the composition space. This modeling amendment ensures that the standard velocity model in conditional moment closure studies can now be used for MMC computation as well. A simplified model for the velocity-dependence of MMC drift coefficients is derived without loss of generality and is implemented for the revised velocity closure. Modeling results have been corroborated against the Direct Numerical Simulation database of a spatially evolving, planar turbulent jet flame. The revised model shows marked improvement over standard MMC closure in predicting velocity statistics close to the nozzle. (author)

Vaishnavi, P. [Mechanical Engineering Department, Imperial College, London SW7 2AZ (United Kingdom); Kronenburg, A. [Institut fuer Technische Verbrennung, Universitaet Stuttgart, 70174 Stuttgart (Germany)

2010-10-15T23:59:59.000Z

172

Single-Duct Constant Air Volume System Supply Air Temperature Reset: Using Return Air Temperature or Outside Air Temperature?  

E-Print Network (OSTI)

The supply air temperature set point for a singleduct constant air volume air handling unit (AHU) system is often reset based on either return air temperature or outside air temperature in order to reduce simultaneous cooling and heating energy consumption. Both reset strategies make engineering sense as long as the reset schedules are reasonable. Quite often the decision to use one over the other is made with the assumption that they will all achieve some sorts of energy savings. However, the impact of these two strategies on AHU energy consumption could be very different. A comparison of these two commonly used supply air temperature reset strategies for a single-duct constant air volume system is presented in this paper. It is shown that from either the building energy consumption or building comfort point of view, the reset strategy based on outside air temperature is inherently better than that based on return air temperature. Significant amount of heating energy savings can be achieved by switching from return air temperature based reset to outside air temperature based reset. The reset strategy can also benefit variable air volume (VAV) AHUs. An improved supply air temperature set point reset control strategy is proposed by combining and staging the outside air and return air temperature based resets.

Wei, G.; Turner, W. D.; Claridge, D.; Liu, M.

2002-01-01T23:59:59.000Z

173

Solar air collector  

SciTech Connect

A solar heating system including a radiant heat collector apparatus made up of an enclosure having glazed panels. The collector provided within the enclosure is upstanding with the enclosure and the collector has heat absorbent flat walls spaced inwardly from the glazed panels. A heat storage core is provided centrally within the collector and spaced from the walls of the collector. The heat storage core includes an insulated housing and a heat retaining member within the insulated housing. Air passageways are formed between the collector walls and the insulated housing for passing input air, and duct members are provided for communicating with a household.

Deschenes, D.; Misrahi, E.

1981-12-15T23:59:59.000Z

174

An Adaptive Dealiasing Method Based on Variational Analysis for Radar Radial Velocities Scanned with Small Nyquist Velocities  

Science Conference Proceedings (OSTI)

Previous velocityazimuth display (VAD)-based methods of dealiasing folded radial velocities have relied heavily on the VAD uniform-wind assumption and, thus, can fail when the uniform-wind assumption becomes poor around azimuthal circles in a ...

Qin Xu; Kang Nai

2012-12-01T23:59:59.000Z

175

Eddy-Correlation Measurements of Air-Sea Fluxes from a Discus Buoy  

Science Conference Proceedings (OSTI)

This paper demonstrates that it is practical to measure turbulent air-sea fluxes from a discus buoy. It proposes a method to correct the measured wind flow, for velocities induced by angular and axial movements of the anemometer, allowing the ...

Franois Anctil; Mark A. Donelan; William M. Drennan; Hans C. Graber

1994-08-01T23:59:59.000Z

176

Hexane Air Combustion  

E-Print Network (OSTI)

Hot surface ignition and subsequent flame propagation of premixed n-hexane air mixtures are shown in this fluid dynamics video. High speed schlieren photography revealed 3 distinct behaviors of ignition and propagation as a function of mixture composition and initial pressure.

Boettcher, Philipp A; Shepherd, Joseph E

2010-01-01T23:59:59.000Z

177

Air-cleaning apparatus  

SciTech Connect

An air-cleaning, heat-exchange apparatus includes a main housing portion connected by means of an air inlet fan to the kitchen exhaust stack of a restaurant. The apparatus includes a plurality of heat exchangers through which a heat-absorptive fluid is circulated, simultaneously, by means of a suitable fluid pump. These heat exchangers absorb heat from the hot exhaust gas, out of the exhaust stack of the restaurant, which flows over and through these heat exchangers and transfers this heat to the circulating fluid which communicates with remote heat exchangers. These remote heat exchangers further transfer this heat to a stream of air, such as that from a cold-air return duct for supplementing the conventional heating system of the restaurant. Due to the fact that such hot exhaust gas is heavily grease laden , grease will be deposited on virtually all internal surfaces of the apparatus which this exhaust gas contacts. Consequently, means are provided for spraying these contacted internal surfaces , as well as the hot exhaust gas itself, with a detergent solution in which the grease is soluble, thereby removing grease buildup from these internal surfaces.

Howard, A.G.

1981-08-18T23:59:59.000Z

178

Winter Morning Air Temperature  

Science Conference Proceedings (OSTI)

Results of temperature measurements, which may be applied to inference of winter temperatures in data-sparse areas, are presented. The morning air temperatures during three winters were measured at 80 places in a 10 km 30 km area along the ...

A. Hogan; M. Ferrick

1997-01-01T23:59:59.000Z

179

Air Proportional Counter  

DOE Patents (OSTI)

A multiple wire counter utilizing air at atmospheric pressure as the ionizing medium and having a window of a nylon sheet of less than 0.5 mil thickness coated with graphite. The window is permeable to alpha particles so that the counter is well adapted to surveying sources of alpha radiation.

Simpson, J.A. Jr.

1950-10-31T23:59:59.000Z

180

Vermont Air Pollution Control Regulations, Ambient Air Quality Standards (Vermont)  

Energy.gov (U.S. Department of Energy (DOE))

The ambient air quality standards are based on the national ambient air quality standards. The Vermont standards are classified as primary and secondary standards and judged adequate to protect...

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Correlations of whitecap coverage and gas transfer velocity with microwave brightness temperature for plunging and spilling breaking waves  

DOE Green Energy (OSTI)

Bubbles and bubble plumes generated by wind-induced breaking waves significantly enhance the gas exchange across the interface between the ocean and atmosphere under high-wind conditions. Whitcaps, or active spilling wave crests, are the sea-surface manifestation of the bubbles and bubble plumes in the subsurface mixed layer, and the fractional area of the sea surface covered by which has been proposed to correlate linearly with the air-sea gas transfer velocity. The presence of whitecaps substantially increases the microwave brightness temperature of the sea surface. It could be possible to estimate the whitecap coverage from the sea-surface microwave brightness temperature would also be very helpful in developing a remote-sensing model for predicting air-sea gas transfer velocities from microwave brightness temperatures. As a part of an air-water gas exchange experiment conducted in an outdoor surf pool, measurements were made that were designed to investigate the correlation between whitecap coverage and microwave brightness temperature. A mechanical wave maker was located at the deep end of the pool and the generated waves propagate and break towards the shallow end of the pool. Two wave patterns characteristic of plunging and spilling breaking waves at four wave heights from 0.3 m to 1.2 m were produced.

Wang, Qin; Monahan, E.C. [Connecticut Univ., Groton, CT (United States). Marine Sciences Inst.; Asher, W.E. [Battelle/Marine Sciences Lab., Sequim, WA (United States); Smith, P.M. [Naval Research Lab. Detachment, Stennis Space Center, MS (United States)

1995-07-01T23:59:59.000Z

182

Forcing and Velocity Correlations in a Vibrated Granular Monolayer  

E-Print Network (OSTI)

The role of forcing on the dynamics of a vertically shaken granular monolayer is investigated. Using a flat plate, surprising negative velocity correlations are measured. A mechanism for this anti-correlation is proposed with support from both experimental results and molecular dynamics simulations. Using a rough plate, velocity correlations are positive, and the velocity distribution evolves from a gaussian at very low densities to a broader distribution at high densities. These results are interpreted as a balance between stochastic forcing, interparticle collisions, and friction with the plate.

Alexis Prevost; David A. Egolf; Jeffrey S. Urbach

2002-03-14T23:59:59.000Z

183

Superconducting spoke cavities for high-velocity applications  

SciTech Connect

To date, superconducting spoke cavities have been designed, developed, and tested for particle velocities up to {beta}{sub 0}~0.6, but there is a growing interest in possible applications of multispoke cavities for high-velocity applications. We have explored the design parameter space for low-frequency, high-velocity, double-spoke superconducting cavities in order to determine how each design parameter affects the electromagnetic properties, in particular the surface electromagnetic fields and the shunt impedance. We present detailed design for cavities operating at 325 and 352 MHz and optimized for {beta}{sub 0}~=0.82 and 1.

Hopper, Christopher S. [Old Dominion U.; Delayen, Jean R. [Old Dominion U., JLAB

2013-10-01T23:59:59.000Z

184

Effects of buoyancy on lean premixed v-flames, Part II. VelocityStatistics in Normal and Microgravity  

Science Conference Proceedings (OSTI)

The field effects of buoyancy on laminar and turbulent premixed v-flames have been studied by the use of laser Doppler velocimetry to measure the velocity statistics in +1g, -1g and {micro}g flames. The experimental conditions covered mean velocity, Uo, of 0.4 to 2 m/s, methane/air equivalence ratio, f, of 0.62 to 0.75. The Reynolds numbers, from 625 to 3130 and the Richardson number from 0.05 to 1.34. The results show that a change from favorable (+1g) to unfavorable (-1g) mean pressure gradient in the plume create stagnating flows in the far field whose influences on the mean and fluctuating velocities persist in the near field even at the highest Re we have investigated. The use of Richardson number flames are direct consequences of buoyancy. Furthermore, the rms fluctuations in the plumes of {micro}g flames are lower and more isotropic than in the laboratory flames to show that the unstable plumes in laboratory flames also induce velocity fluctuations. The phenomena influenced by buoyancy i.e. degree of flame wrinkling, flow acceleration, flow distribution, and turbulence production, can be subtle due to their close coupling with other flame flow interaction processes. But they cannot be ignored in fundamental studies or else the conclusions and insights would be ambiguous and not very meaningful.

Cheng, R.K.; Bedat, B.; Yegian, D.T.

1999-07-01T23:59:59.000Z

185

Evaluation of Air Mixing and Thermal Comfort From High Sidewall Supply Air Jets  

SciTech Connect

Uniform mixing of conditioned air with room air is an essential factor for providing comfort in homes. The higher the supply flow rates the easier to reach good mixing in the space. In high performance homes, however, the flow rates required to meet the small remaining thermal loads are not large enough to maintain uniform mixing in the space. The objective of this study is to resolve this issue and maintain uniform temperatures within future homes. We used computational fluid dynamics modeling to evaluate the performance of high sidewall air supply for residential applications in heating and cooling modes. Parameters of the study are the supply velocity, supply temperature, diffuser dimensions, and room dimensions. Laboratory experiments supported the study of thermal mixing in heating mode; we used the results to develop a correlation to predict high sidewall diffuser performance. For cooling mode, numerical analysis is presented. The results provide information to guide the selection of high sidewall supply diffusers to maintain proper room mixing for heating and cooling of high performance homes. It is proven that these systems can achieve good mixing and provide acceptable comfort levels. Recommendations are given on the operating conditions to guarantee occupant comfort.

Ridouane, E. H.

2011-09-01T23:59:59.000Z

186

Air Conditioning | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Conditioning Conditioning Air Conditioning July 1, 2012 - 6:28pm Addthis Air conditioners cost U.S. homeowners more than $11 billion each year, and regular maintenance can keep your air conditioner running efficiently. | Photo courtesy of ©iStockphoto/JaniceRichard Air conditioners cost U.S. homeowners more than $11 billion each year, and regular maintenance can keep your air conditioner running efficiently. | Photo courtesy of ©iStockphoto/JaniceRichard How does it work? An air conditioner uses energy -- usually electricity -- to transfer heat from the interior of your home to the relatively warm outside environment. Two-thirds of all homes in the United States have air conditioners. Air conditioners use about 5% of all the electricity produced in the United States, at an annual cost of more than $11 billion to homeowners. As a

187

Judging Air Quality Model Performance  

Science Conference Proceedings (OSTI)

Under the direction of the AMS Steering Committee for the EPA Cooperative Agreement on air quality modeling, a small group of scientists was convened to review and recommend procedures to evaluate the performance of air quality models. Particular ...

Douglas G. Fox

1981-05-01T23:59:59.000Z

188

Oil and Gas Air Heaters  

E-Print Network (OSTI)

Most conventional air heaters adopt indirect heat transfer, which uses combustion gases to indirectly heat fresh air by heating surfaces to generate hot air used for material drying and dehumidification. We call them indirect air heaters. However, they have a higher manufacturing cost and lower thermal efficiency, especially when high temperature air is needed. For this reason, a direct air heater applicable for or feed and industrial raw products is put forward, which has advantages such as less production cost, smaller dimensions and higher thermal efficiency. Their design, working principles, characteristics, structure and applications are presented in this article, and brief comparisons are made between the indirect and direct air heater. Finally, the relation of hot-air temperature, oil or gas consumption and fresh airflow is determined based on energy equilibrium.

Kou, G.; Wang, H.; Zhou, J.

2006-01-01T23:59:59.000Z

189

Computer controlled air conditioning systems  

SciTech Connect

This patent describes an improvement in a computer controlled air conditioning system providing for circulation of air through an air conditioned house in contact with concrete walls requiring a humidity within a critical range. The improvement consists of: a computer for processing sensed environmental input data including humidity and oxygen to produce output control signals for affecting the humidity of the air in the house; provision for an air flow circulation path through the house in contact with the concrete walls; sensing responsive to the amount of oxygen in the house for providing input signals to the computer; mixing for combining with the air in the house a variable amount of fresh atmospheric air to supply fresh oxygen; and humidity modifying means for modifying the humidity of the air flowing in the flow path responsive to the control signals.

Dumbeck, R.F.

1986-02-04T23:59:59.000Z

190

Louisiana Air Control Law (Louisiana)  

Energy.gov (U.S. Department of Energy (DOE))

This law states regulations for air quality control and states the powers and duties of the secretary of environmental quality. It provides information about permits and licenses, air quality...

191

Uncertainty in Air Quality Modeling  

Science Conference Proceedings (OSTI)

Under the direction of the AMS Steering Committee for the EPA Cooperative Agreement on Air Quality Modeling, a small group of scientists convened to consider the question of uncertainty in air quality modeling. Because the group was particularly ...

Douglas G. Fox

1984-01-01T23:59:59.000Z

192

Composite Vertical Structure of Vertical Velocity in Nonprecipitating Cumulus Clouds  

Science Conference Proceedings (OSTI)

Vertical transects of Doppler vertical velocity data, obtained from an airborne profiling millimeter-wave cloud radar, are composited for a large number of cumulus clouds (Cu) at various stages of their life cycle, to examine typical circulations ...

Yonggang Wang; Bart Geerts

2013-05-01T23:59:59.000Z

193

Seismic Velocity And Attenuation Structure Of The Geysers Geothermal Field,  

Open Energy Info (EERE)

Velocity And Attenuation Structure Of The Geysers Geothermal Field, Velocity And Attenuation Structure Of The Geysers Geothermal Field, California Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Seismic Velocity And Attenuation Structure Of The Geysers Geothermal Field, California Details Activities (1) Areas (1) Regions (0) Abstract: The Geysers geothermal field is located in northern California and is one of the world's largest producers of electricity from geothermal energy. A key resource management issue at this field is the distribution of fluid in the matrix of the reservoir rock. In this paper, we interpret seismic compressional-wave velocity and quality quotient (Q) data at The Geysers in terms of the geologic structure and fluid saturation in the reservoir. Our data consist of waveforms from approximately 300

194

Y-12 Site Experience with Deposition Velocity Issues  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Site Experience with Site Experience with Deposition Velocity Issues Douglas Clark Analyst B&W Technical Services Y-12 May 9, 2012 Y-12 Site Experience with Deposition Velocity Issues Y-12 Specific Issues Y-12 Site Experience with Deposition Velocity Issues Windspeed - Calm Wind Conditions at Y-12 Site Y-12 Site Experience with Deposition Velocity Issues Windspeed - Stability Class Determinations * NRC RG 1.23 ΔT-only method * EPA-454/R-99-005 solar- radiation-delta-temperature (SRDT) method * Hybrid SR - DT method * wind direction standard deviation [sigma-theta (σ θ )] * elevation angle standard deviation [sigma-phi (σ φ )] * vertical wind speed standard deviation [sigma-omega (σ ω )], * wind-speed ratio method (u R ) * All evaluated using data from west

195

Property:Maximum Velocity(m/s) | Open Energy Information  

Open Energy Info (EERE)

Velocity(m/s) Velocity(m/s) Jump to: navigation, search Property Name Maximum Velocity(m/s) Property Type String Pages using the property "Maximum Velocity(m/s)" Showing 25 pages using this property. (previous 25) (next 25) A Alden Large Flume + 0.9 + B Bucknell Hydraulic Flume + 2.7 + C Carderock Maneuvering & Seakeeping Basin + 7.2 + Carderock Rotating Arm Tow Tank + 25.8 + Carderock Tow Tank 1 + 9.3 + Carderock Tow Tank 2 + 10.3 + Carderock Tow Tank 3 + 25.8 + Chase Tow Tank + 2.5 + D Davidson Laboratory Tow Tank + 18.3 + H Haynes Tow Tank + 1.8 + I Ice Towing Tank + 0.5 + L Lakefront Tow Tank + 2.7 + M MHL Free Surface Channel + 2 + MHL High Speed Cavitation + 25.9 + MHL Tow Tank + 6.7 + MIT Tow Tank + 1.5 + MMA Tugboat/ Barge/ Vessel + 5.1 + Maine Tow Tank + 3 +

196

Property:Velocity(m/s) | Open Energy Information  

Open Energy Info (EERE)

Velocity(m/s) Velocity(m/s) Jump to: navigation, search Property Name Velocity(m/s) Property Type String Pages using the property "Velocity(m/s)" Showing 21 pages using this property. A Alden Small Flume + >0.9 + B Bucknell Hydraulic Flume + 2.7 + C Carderock 2-ft Variable Pressure Cavitation Water Tunnel + 17 + Carderock 3-ft Variable Pressure Cavitation Water Tunnel + 25.8 + Carderock Circulating Water Channel + 5.2 + Carderock Large Cavitation Tunnel + 18 + Carderock Subsonic Wind Tunnel + 83.8 + D DeFrees Flume 1 + 2 + DeFrees Flume 2 + 2 + DeFrees Flume 3 + 2 + DeFrees Flume 4 + 2 + M MHL Free Surface Channel + 2 + MHL High Speed Cavitation + 25.9 + MHL Student Tunnel + 4.6 + P Penn Large Water Tunnel + 16.8 + Penn Small Water Tunnel + 21 + S SAFL Channel + 6.1 +

197

Vertical Velocity Structures in an Axisymmetric, Nonhydrostatic Tropical Cyclone Model  

Science Conference Proceedings (OSTI)

A statistical analysis of several experiments with different microphysical parameterizations in an axisymmetric, nonhydrostatic tropical cyclone model illustrates the impact of icc-phase microphysics on model vertical velocity structure. The ...

Stephen J. Lord; Jacqueline M. Lord

1988-05-01T23:59:59.000Z

198

Universal Velocity-Field Characteristics for a Nanowire Arbitrary Degeneracy  

Science Conference Proceedings (OSTI)

The effects of electric field on the carrier motion and drift velocity in nanowire (NW) are presented in this paper. When the electric field is applied in NW, the electron is expected to move in anti-parallel direction to the electric field. This is so-called randomness motion is transformed into streamlined motion in extremely high electric field. The normalized Fermi energy and relative electron population as a function of electric field are examined for various degeneracies. It was found that the electric field has lesser influence on the relative electron population with the increased degeneracy. The drift velocity in NW is shown to increase with electric field until it reaches the saturation velocity. Two approximations have been made to simplify the theoretical equation. It is also shown in this paper that when the quantum emission is taken into account, the drift and saturation velocity degrades.

Chek, Desmond C. Y.; Hashim, Abdul Manaf [Faculty of Electrical Eng., Universiti Teknologi Malaysia, 81310 Skudai, Johor (Malaysia); Tan, Michael Loong Peng [Faculty of Electrical Eng., Universiti Teknologi Malaysia, 81310 Skudai, Johor (Malaysia); Electrical Engineering Division, Engineering Department, University of Cambridge, 9 J.J. Thomson Avenue, Cambridge CB3 0FA (United Kingdom); Arora, Vijay K. [Faculty of Electrical Eng., Universiti Teknologi Malaysia, 81310 Skudai, Johor (Malaysia); Division of Engineering and Physics, Wilkes University, Wilkes-Barre, PA 18766 (United States)

2011-05-25T23:59:59.000Z

199

Detiding Three-Dimensional Velocity Survey Data in Coastal Waters  

Science Conference Proceedings (OSTI)

A three-dimensional data interpolation technique is proposed that efficiently removes tidal currents from spatial velocity surveys. The least squares method extends prior two-dimensional detiding methods to three spatial dimensions using ...

Andreas Mnchow

2000-05-01T23:59:59.000Z

200

The Finescale Response of Lowered ADCP Velocity Profiles  

Science Conference Proceedings (OSTI)

Lowered acoustic Doppler current profiler (LADCP) velocity profiles are compared with simultaneous higher-resolution expendable current profiler (XCP) profiles to determine the lowered ADCP's response at short wavelengths. Although lowered ADCP ...

Kurt Polzin; Eric Kunze; Jules Hummon; Eric Firing

2002-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Mass Transport Velocity in Free Barotropic Poincar Waves  

Science Conference Proceedings (OSTI)

The mass transport velocity induced by long surface waves in a shallow, rotating viscous ocean is studied theoretically by using a Lagrangian description of motion. The depth is constant, and the water is homogeneous. Such waves are referred to ...

Frode Hydalsvik; Jan Erik Weber

2003-09-01T23:59:59.000Z

202

TOPS: A Free-Fall Velocity and CTD Profiler  

Science Conference Proceedings (OSTI)

A free-fall instrument, TOPS, measures vertical profiles of horizontal ocean velocity, conductivity and temperature. Profiling capability extends throughout the full water column (6000 db pressure limitation). Larger vertical wavelength (water ...

S. P. Hayes; H. B. Milburn; E. F. Ford

1984-09-01T23:59:59.000Z

203

LOW VELOCITY SHPERE IMPACT OF SODA LIME SILICATE GLASS  

Science Conference Proceedings (OSTI)

This report summarizes TARDEC-sponsored work at Oak Ridge National Laboratory (ORNL) during the FY11 involving low velocity ( 30 m/s or 65 mph) ball impact testing of Starphire soda lime silicate glass. The intent was to better understand low velocity impact response in the Starphire for sphere densities that bracketed that of rock. Five sphere materials were used: borosilicate glass, soda-lime silicate glass, steel, silicon nitride, and alumina. A gas gun was fabricated to produce controlled velocity delivery of the spheres against Starphire tile targets. Minimum impact velocities to initiate fracture in the Starphire were measured and interpreted in context to the kinetic energy of impact and the elastic property mismatch between the any of the five sphere-Starphire-target combinations.

Morrissey, Timothy G [ORNL; Fox, Ethan E [ORNL; Wereszczak, Andrew A [ORNL; Vuono, Daniel J [ORNL

2012-01-01T23:59:59.000Z

204

Representation of Velocity Gradient Effects in a Gaussian Puff Model  

Science Conference Proceedings (OSTI)

The Gaussian puff model framework is extended to provide a description of velocity shear distortion effects. An efficient splitting-merging algorithm is presented so that a maximum puff size can be specified for a calculation. This localizes the ...

R. I. Sykes; D. S. Henn

1995-12-01T23:59:59.000Z

205

Equatorial Atlantic Velocity and Temperature Observations: FebruaryNovember 1981  

Science Conference Proceedings (OSTI)

Upper ocean velocity and temperature measurements were obtained in the central equatorial Atlantic using surface moored current meters from February to November 1981. Distinct seasonal variations were observed in the zonal momentum and ...

R. H. Weisberg

1985-05-01T23:59:59.000Z

206

Simulation of Three-Dimensional Turbulent Velocity Fields  

Science Conference Proceedings (OSTI)

New algorithms for the simulation of three-dimensional homogeneous turbulent velocity fields are compared with standard spectral domain algorithms. Results are presented for a von Krmn model of the covariance tensor. For typical atmospheric ...

Rod Frehlich; Larry Cornman; Robert Sharman

2001-02-01T23:59:59.000Z

207

A New Relationship between Mean Doppler Velocity and Differential Reflectivity  

Science Conference Proceedings (OSTI)

A new relationship has been established linking the vertical mean Doppler velocity of raindrop spectra and the accompanying differential reflectivities. It is based upon the specific radar combination of a vertically pointing Doppler and a ...

Matthias Steiner

1991-06-01T23:59:59.000Z

208

Dealiasing of Doppler Radar Velocities Using a Torus Mapping  

Science Conference Proceedings (OSTI)

A novel dealiasing algorithm for Doppler radar velocity data has been developed at the Swedish Meteorological and Hydrological Institute (SMHI). Unlike most other methods, it does not need independent wind information from other instruments (e.g.,...

Gnther Haase; Tomas Landelius

2004-10-01T23:59:59.000Z

209

Eulerian and Lagrangian Velocity Distributions in the North Atlantic  

Science Conference Proceedings (OSTI)

Velocity probability density functions (PDFs) are calculated using data from subsurface current meters in the western North Atlantic Ocean. The PDFs are weakly, but significantly, non-Gaussian. They deviate from normality because of an excess of ...

J. H. LaCasce

2005-12-01T23:59:59.000Z

210

Benthic Boundary-Layer Velocity Profiles: Dependence on Averaging Period  

Science Conference Proceedings (OSTI)

The relationship between benthic boundary-layer velocity profiles and current meter averaging time is investigated using detailed (0.61 Hz) current measurements recorded within 1 m of the bottom on the inner continental shelf. The percentage of ...

Barry M. Lesht

1980-06-01T23:59:59.000Z

211

GPS velocity field for the Tien Shan and surrounding regions  

E-Print Network (OSTI)

Measurements at ?400 campaign-style GPS points and another 14 continuously recording stations in central Asia define variations in their velocities both along and across the Kyrgyz and neighboring parts of Tien Shan. They ...

Zubovich, Alexander V.

212

Profiler Measurements of Vertical Velocity Fluctuations in the Ocean  

Science Conference Proceedings (OSTI)

A method is described for measuring the vertical component of velocity fluctuations due to three-dimensional turbulence in the ocean from a freely falling microstructure profiler. The dynamic pressure measurement relies on a commercially ...

J. N. Moum

1990-04-01T23:59:59.000Z

213

Deep Velocity Measurements in the Western Equatorial Indian Ocean  

Science Conference Proceedings (OSTI)

Vertical profiles of horizontal current collected in April and June 1979 in the western Indian Ocean revealed the presence of short vertical scale (150300 m) deep zonal jets, trapped to within 1 of the equator. Meridional velocity records ...

Rui M. Ponte; James Luyten

1990-01-01T23:59:59.000Z

214

Vorticity from Line-of-Sight Lidar Velocity Scans  

Science Conference Proceedings (OSTI)

A method is presented to compute the spanwise vorticity in polar coordinates from 2D vertical cross sections of high-resolution line-of-sight Doppler wind lidar observations. The method uses the continuity equation to derive the velocity ...

Martin Weissmann; Andreas Drnbrack; James D. Doyle

2009-12-01T23:59:59.000Z

215

Platform-Motion Correction of Velocity Measured by Doppler Lidar  

Science Conference Proceedings (OSTI)

The NOAA/Earth System Research Laboratory (ESRL) has two coherent Doppler lidar systems that have been deployed on board research vessels to obtain data during several experiments. The instruments measure the wind velocity relative to the motion ...

Reginald J. Hill; W. Alan Brewer; Sara C. Tucker

2008-08-01T23:59:59.000Z

216

A triple hot-wire system for indoor air flow measurements  

SciTech Connect

The application of a home made, triple hot-wire system in indoor air flow measurements is presented. Both the anemometer and sensor have been developed at Athens University with the aim to provide a reliable, research tool of reasonable cost, simple construction, and satisfactory performance. All three velocity components above a threshold of 10 cm s{sup {minus}1} can be measured. The system is also equipped with two thermometers for measuring the mean and fluctuating air temperature and for providing a means of temperature compensation of the hot wires` signal. After evaluation of the system in the laboratory, it was used in the measurement of the velocity profile of flows driven by the temperature difference between two internal zones. The implied accuracy of the method allows for its integration with measurements of air volume exchange rates between internal zones, as estimated by tracer gas techniques.

Papadopoulos, K.H.; Soilemes, A.T.; Helmis, C.G.; Santamouris, M.; Dascalaki, E. [Univ. of Athens (Greece); Asimakopoulos, D.N. [Univ. of Athens (Greece)]|[National Observatory of Athens (Greece). Inst. of Meteorology and Physics of the Atmospheric Environment; Argiriou, A. [National Observatory of Athens (Greece). Inst. of Meteorology and Physics of the Atmospheric Environment

1996-08-01T23:59:59.000Z

217

Compressed Air 101: Getting Compressed Air to Work  

E-Print Network (OSTI)

"Air compressors are a significant industrial energy user. Based on a survey (conducted by Oregon State University and the Bonneville Power Administration) of energy audit reports from 125 plants, air compressors account for roughly 10% of total plant energy use. Furthermore, air compression is inefficient with up to 95% of compressor power dissipated as heat. Thus even minor improvements in system operation, control strategies, and efficiency can yield large energy savings and significant non-energy or productivity benefits from reliable compressed air. Compressed air is often called the ""fourth utility"" in industrial facilities after electricity, natural gas, and water. It provides motive power for machinery, cooling, materials handling, and hand tools. It is a safe, flexible, and powerful resource, but one that is seldom run for low operating costs or best productivity. Learning the basics of compressed air systems represents the beginning of both reducing energy costs and enjoying the productive benefits of reliable compressed air. Compressed air management systems, including a system approach to managing demand, stabilizing pressure, reducing leaks and compressor controls, can allow the industrial end user to save 20% - 50% of their air compressor electricity usage. The monitoring capabilities of compressed air management systems provide a useful tool through power, pressure and flow trending to maintain both the energy savings and increased system reliability. More efficiently managed compressed air systems are less costly to maintain and have less impact on the environment. The most important issues of industrial compressed air in relation to energy efficiency and management are: 1. Compressed air is an essential industrial utility; 2. Compressing air is a fundamentally inefficient energy transformation process; 3. Optimal operation of compressed air systems in industrial plants is seldom a priority and adequate management infonnation is rare, resulting in negative impacts on production and even less efficiency."

Burke, J. J.; Bessey, E. G.

2003-05-01T23:59:59.000Z

218

Metal-air battery assessment  

DOE Green Energy (OSTI)

The objective of this report is to evaluate the present technical status of the zinc-air, aluminum/air and iron/air batteries and assess their potential for use in an electric vehicle. In addition, this report will outline proposed research and development priorities for the successful development of metal-air batteries for electric vehicle application. 39 refs., 25 figs., 11 tabs.

Sen, R.K.; Van Voorhees, S.L.; Ferrel, T.

1988-05-01T23:59:59.000Z

219

California Air Resources Board | Open Energy Information  

Open Energy Info (EERE)

Air Resources Board Jump to: navigation, search Logo: California Air Resources Board Name California Air Resources Board Place Sacramento, California Website http:www.arb.ca.gov...

220

Review of air flow measurement techniques  

E-Print Network (OSTI)

rate and air leakage tests under reductive sealing for anfor subsequent sealing, the openings of air infiltrationreductive sealing between the reductions in measured air

McWilliams, Jennifer

2002-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Air cathode structure manufacture  

DOE Patents (OSTI)

An improved air cathode structure for use in primary batteries and the like. The cathode structure includes a matrix active layer, a current collector grid on one face of the matrix active layer, and a porous, nonelectrically conductive separator on the opposite face of the matrix active layer, the collector grid and separator being permanently bonded to the matrix active layer. The separator has a preselected porosity providing low IR losses and high resistance to air flow through the matrix active layer to maintain high bubble pressure during operation of the battery. In the illustrated embodiment, the separator was formed of porous polypropylene. A thin hydrophobic film is provided, in the preferred embodiment, on the current collecting metal grid.

Momyer, William R. (Palo Alto, CA); Littauer, Ernest L. (Los Altos Hills, CA)

1985-01-01T23:59:59.000Z

222

Transpired Air Collectors - Ventilation Preheating  

DOE Green Energy (OSTI)

Many commercial and industrial buildings have high ventilation rates. Although all that fresh air is great for indoor air quality, heating it can be very expensive. This short (2-page) fact sheet describes a technology available to use solar energy to preheat ventilation air and dramatically reduce utility bills.

Christensen, C.

2006-06-22T23:59:59.000Z

223

Solar air conditioning  

DOE Green Energy (OSTI)

Development of a hybrid solar-assisted air conditioning system that combines a vapor compression section for sensible cooling with a desiccant section for dehumidification and that uses both solar energy and condenser waste heat to drive the dehumidifier has been under way for the last two years (1981 and 1982). The results of this research are included in this report: utilizing solar energy in an economical way has proven quite difficult.

Robison, H.

1981-01-01T23:59:59.000Z

224

Air Resources Board  

E-Print Network (OSTI)

The Air Resources Board (ARB or Board) will conduct a public hearing at the time and place noted below to consider adoption of the Proposed Airborne Toxic Control Measure (ATCM) to Reduce Formaldehyde Emissions from Composite Wood Products. The proposed ATCM would reduce the publics current exposure to formaldehyde by reducing emissions from hardwood plywood (HWPW), particleboard (PB) and medium density fiberboard (MDF) panels. The ATCM would also apply to finished goods made with these materials.

unknown authors

2007-01-01T23:59:59.000Z

225

Premixed flame kinematics in a harmonically oscillating velocity field .  

E-Print Network (OSTI)

??Air pollution regulations have driven modern power generation systems to move from diffusion to premixed combustion. However, these premixed combustion systems are prone to combustion (more)

Shin, Dong-hyuk

2012-01-01T23:59:59.000Z

226

VELOCITY EVOLUTION AND THE INTRINSIC COLOR OF TYPE Ia SUPERNOVAE  

SciTech Connect

To understand how best to use observations of Type Ia supernovae (SNe Ia) to obtain precise and accurate distances, we investigate the relations between spectra of SNe Ia and their intrinsic colors. Using a sample of 1630 optical spectra of 255 SNe, based primarily on data from the CfA Supernova Program, we examine how the velocity evolution and line strengths of Si II {lambda}6355 and Ca II H and K are related to the B - V color at peak brightness. We find that the maximum-light velocity of Si II {lambda}6355 and Ca II H and K and the maximum-light pseudo-equivalent width of Si II {lambda}6355 are correlated with intrinsic color, with intrinsic color having a linear relation with the Si II {lambda}6355 measurements. Ca II H and K does not have a linear relation with intrinsic color, but lower-velocity SNe tend to be intrinsically bluer. Combining the spectroscopic measurements does not improve intrinsic color inference. The intrinsic color scatter is larger for higher-velocity SNe Ia-even after removing a linear trend with velocity-indicating that lower-velocity SNe Ia are more 'standard crayons'. Employing information derived from SN Ia spectra has the potential to improve the measurements of extragalactic distances and the cosmological properties inferred from them.

Foley, Ryan J.; Sanders, Nathan E.; Kirshner, Robert P., E-mail: rfoley@cfa.harvard.edu [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, Cambridge, MA 02138 (United States)

2011-12-01T23:59:59.000Z

227

Design of regulated velocity flow assurance device for petroleum industry  

E-Print Network (OSTI)

The petroleum industry faces problems in transportation of crude petroleum be- cause of the deposition of paraffins, hydrates and asphaltenes on the insides of the pipeline. These are conventionally removed using either chemical inhibitors or mechani- cal devices, called pigs, which travel through the pipeline and mechanically scrape away the deposits. These pigs are propelled by the pipeline product itself and hence travel at the same velocity as the product. Research has indicated that cleaning would be better if the pigs are traveling at a relatively constant velocity of around 70% of the product velocity. This research utilizes the concept of regulating the bypass flow velocity in order to maintain the pig velocity. The bypass flow is regulated by the control unit based on the feedback from the turbine flowmeter, which monitors the bypass flow. A motorized butterfly valve is used for actually controlling the bypass flow. In addition to cleaning, the proposed pig utilizes on-board electronics like accelerom- eter and pressure transducers to store the data gathered during the pig run. This data can then be analyzed and the condition of the pipeline predicted. Thus, this research addresses the problem of designing a pig to maintain a constant velocity in order to achieve better cleaning. It also helps gather elementary data that can be used to predict the internal conditions in the pipe.

Yardi, Chaitanya Narendra

2004-12-01T23:59:59.000Z

228

Air Pollution Control Regulations: No. 22 - Air Toxics (Rhode Island) |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Air Pollution Control Regulations: No. 22 - Air Toxics (Rhode Air Pollution Control Regulations: No. 22 - Air Toxics (Rhode Island) Air Pollution Control Regulations: No. 22 - Air Toxics (Rhode Island) < Back Eligibility Commercial Industrial Investor-Owned Utility Municipal/Public Utility Rural Electric Cooperative Utility Program Info State Rhode Island Program Type Siting and Permitting Provider Department of Environmental Management Permits are required to construct, install, or modify any stationary source which has the potential to increase emissions of a listed toxic air contaminant by an amount greater than the minimum quantity for that contaminant. Minimum quantities are specified in Table III of these regulations. Permits will be granted based in part on the impact of the projected emissions of the stationary source on acceptable ambient levels

229

Urban and Regional Air Quality  

NLE Websites -- All DOE Office Websites (Extended Search)

equipment equipment Urban and Regional Air Quality Research in this area is concerned with regional air quality issues such as: Controlling nitrogen oxides (NOx) and volatile organic compounds, to manage tropospheric ozone pollution. Hazardous air pollutants: using science to base standards on rigorously studied risks. Air quality and climate: how does climate influence air quality at a regional or local level? Current modeling practices often do not capture variations in pollutants such as ozone-they represent a limited sample of the diverse meteorology and human behavior that affect air pollution. Improved modeling of regional air quality will help understand variability, reveal patterns of behavior, and pollutant transport issues. Controlled experiments in lab and field can help validate improved models.

230

An Improved Gaussian Jet Model for Deriving Absolute Geostrophic Velocity from Satellite Altimetry  

Science Conference Proceedings (OSTI)

Key aspects of a Gaussian jet model for deriving absolute geostrophic velocity from TOPEX/Poseidon altimeter data are improved. Velocities are obtained by synthesizing Gaussian fits to cross-stream velocity anomaly profiles of the Kuroshio and ...

Seung-Bum Kim; M. A. Saunders

2002-12-01T23:59:59.000Z

231

Effects of buoyancy on lean premixed v-flames, Part II. VelocityStatistics in Normal and Microgravity  

SciTech Connect

The field effects of buoyancy on laminar and turbulent premixed v-flames have been studied by the use of laser Doppler velocimetry to measure the velocity statistics in +1g, -1g and {micro}g flames. The experimental conditions covered mean velocity, Uo, of 0.4 to 2 m/s, methane/air equivalence ratio, f, of 0.62 to 0.75. The Reynolds numbers, from 625 to 3130 and the Richardson number from 0.05 to 1.34. The results show that a change from favorable (+1g) to unfavorable (-1g) mean pressure gradient in the plume create stagnating flows in the far field whose influences on the mean and fluctuating velocities persist in the near field even at the highest Re we have investigated. The use of Richardson number < 0.1 as a criterion for momentum dominance is not sufficient to prescribe an upper limit for these buoyancy effects. In {micro}g, the flows within the plumes are non-accelerating and parallel. Therefore, velocity gradients and hence mean strain rates in the plumes of laboratory flames are direct consequences of buoyancy. Furthermore, the rms fluctuations in the plumes of {micro}g flames are lower and more isotropic than in the laboratory flames to show that the unstable plumes in laboratory flames also induce velocity fluctuations. The phenomena influenced by buoyancy i.e. degree of flame wrinkling, flow acceleration, flow distribution, and turbulence production, can be subtle due to their close coupling with other flame flow interaction processes. But they cannot be ignored in fundamental studies or else the conclusions and insights would be ambiguous and not very meaningful.

Cheng, R.K.; Bedat, B.; Yegian, D.T.

1999-07-01T23:59:59.000Z

232

Natural air motion and stratification in passive buildings  

DOE Green Energy (OSTI)

Natural convection is a major mechanism for heat distribution in many passive solar buildings, especially those with sunspaces. To better understand this mechanism, observations of air velocities and temperatures have been made in 13 different houses that encompass a wide variety of one- and two-story geometries. This paper extends previous reports. Results from one house are described in detail, and some generalizations are drawn from the large additional mass of data taken. A simple mathematical model is presented that describes the general nature of airflow and energy flow through an aperture.

Balcomb, J.D.; Jones, G.F.; Yamaguchi, Kenjiro

1984-01-01T23:59:59.000Z

233

Detonability of H/sub 2/-air-diluent mixtures  

DOE Green Energy (OSTI)

This report describes the Heated Detonation Tube (HDT). Detonation cell width and velocity results are presented for H/sub 2/-air mixtures, undiluted and diluted with CO/sub 2/ and H/sub 2/O for a range of H/sub 2/ concentration, initial temperature and pressure. The results show that the addition of either CO/sub 2/ or H/sub 2/O significantly increases the detonation cell width and hence reduces the detonability of the mixture. The results also show that the detonation cell width is reduced (detonability is increased) for increased initial temperature and/or pressure.

Tieszen, S.R.; Sherman, M.P.; Benedick, W.B.; Berman, M.

1987-06-01T23:59:59.000Z

234

Improved particle impactor assembly for size selective high volume air sampler  

DOE Patents (OSTI)

Air containing entrained particulate matter is directed through a plurality of parallel, narrow, vertically oriented apertures of an inlet element toward an adjacently located, relatively large, dust impaction surface preferably covered with an adhesive material. The air flow turns over the impaction surface, leaving behind, the relatively larger particles and passes through two elongate apertures defining the outer bounds of the impaction collection surface to pass through divergent passages which slow down and distribute the air flow, with entrained smaller particles, over a fine filter element that separates the fine particles from the air. By appropriate selection of dimensions and the number of inlet apertures air flow through the inlet element is provided a nonuniform velocity distribution with the lower velocities being obtained near the center of the inlet apertures, to separate out particles larger than a certain predetermined size on the impaction collection surface. The impaction collection surface, even in a moderately sized apparatus, is thus relatively large and permits the prolonged sampling of air for periods extending to four weeks. 6 figs.

Langer, G.

1987-03-23T23:59:59.000Z

235

Regenerative air heater  

DOE Patents (OSTI)

A gas-cooled steel skirt is used to support a refractory cored brick matrix and dome structure in a high temperature regenerative air heater useful in magnetohydrodynamic power generation. The steel skirt thermally expands to accommodate the thermal expansion of the dome structure despite substantial temperature differential thereby reducing relative movement between the dome bricks. Gas cooling of the steel skirt allows the structure to operate above its normal temperature during clean-out cycles and also allows for the control of the thermal expansion of the steel skirt.

Hasselquist, Paul B. (Maple Grove, MN); Baldner, Richard (Minnetonka, MN)

1982-01-01T23:59:59.000Z

236

Regenerative air heater  

DOE Patents (OSTI)

A gas-cooled steel skirt is used to support a refractory cored brick matrix and dome structure in a high temperature regenerative air heater useful in magnetohydrodynamic power generation. The steel skirt thermally expands to accommodate the thermal expansion of the dome structure despite substantial temperature differential thereby reducing relative movement between the dome bricks. Gas cooling of the steel skirt allows the structure to operate above its normal temperature during clean-out cycles and also allows for the control of the thermal expansion of the steel skirt.

Hasselquist, P.B.; Baldner, R.

1980-11-26T23:59:59.000Z

237

Retrofit Air Preheat Economics  

E-Print Network (OSTI)

Retrofit air preheat systems are the most reliable and efficient means to effect significant energy conservation for large existing industrial furnaces. Units can be quickly installed without a lengthy shutdown, and the furnace efficiency can be increased to a range of 89% to 92%. The economic justification for the addition of this equipment is presented in new total investment curves and simple payout curves for a range of fuel cost. This will enable the owner to quickly determine the preliminary feasibility and conceptual requirements for his project before proceeding with more vigorous work.

Goolsbee, J. A.

1981-01-01T23:59:59.000Z

238

Hot air drum evaporator  

DOE Patents (OSTI)

An evaporation system for aqueous radioactive waste uses standard 30 and 55 gallon drums. Waste solutions form cascading water sprays as they pass over a number of trays arranged in a vertical stack within a drum. Hot dry air is circulated radially of the drum through the water sprays thereby removing water vapor. The system is encased in concrete to prevent exposure to radioactivity. The use of standard 30 and 55 gallon drums permits an inexpensive compact modular design that is readily disposable, thus eliminating maintenance and radiation build-up problems encountered with conventional evaporation systems.

Black, Roger L. (Idaho Falls, ID)

1981-01-01T23:59:59.000Z

239

Exceptional Ground Accelerations and Velocities Caused by Earthquakes  

Science Conference Proceedings (OSTI)

This project aims to understand the characteristics of the free-field strong-motion records that have yielded the 100 largest peak accelerations and the 100 largest peak velocities recorded to date. The peak is defined as the maximum magnitude of the acceleration or velocity vector during the strong shaking. This compilation includes 35 records with peak acceleration greater than gravity, and 41 records with peak velocities greater than 100 cm/s. The results represent an estimated 150,000 instrument-years of strong-motion recordings. The mean horizontal acceleration or velocity, as used for the NGA ground motion models, is typically 0.76 times the magnitude of this vector peak. Accelerations in the top 100 come from earthquakes as small as magnitude 5, while velocities in the top 100 all come from earthquakes with magnitude 6 or larger. Records are dominated by crustal earthquakes with thrust, oblique-thrust, or strike-slip mechanisms. Normal faulting mechanisms in crustal earthquakes constitute under 5% of the records in the databases searched, and an even smaller percentage of the exceptional records. All NEHRP site categories have contributed exceptional records, in proportions similar to the extent that they are represented in the larger database.

Anderson, John

2008-01-17T23:59:59.000Z

240

Air Distribution and Microenvironment Evaluation of a Desktop Task Conditioning System  

E-Print Network (OSTI)

Task conditioning aims to provide each occupant with personalized clean air direct to the breathing zone. The microenvironment of a typical office workplace, consisting of two desktop task conditioning systems (a Horizontal Desk Grill (HDG) and Vertical Desk Grill (VDG)) were studied by numerical simulation. Numerical simulation by k- 3-D turbulent flow was separately conducted to study the influence of supply velocity on the microenvironment of these two desktop task conditioning systems. Three task conditioning velocities were studied. Temperature and velocity distribution, Draught Rating (DR) and Predicted Percentage of Dissatisfied (PPD) of the room and workstation were applied to study the performance of task air conditioning. Results show that the performances of HDG and VDG are almost the same. Results also show that task conditioning can provide excellent working environment when supply velocity is well designed. The supply velocity of task conditioning can be set between 0.8-1.0 m/s. However, task conditioning may cause draught, and engineers should seriously consider this problem. The results can provide important references for design and optimization of the task conditioning system.

Zheng, G.

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Complete CFD analysis of a Velocity XL-5 RG with flight-test verification  

E-Print Network (OSTI)

The Texas A&M Flight Research Laboratory (FRL) recently received delivery of its newest aircraft, the Velocity XL-5 RG. The Velocity can fly faster than the other aircraft owned by the FRL and does not have a propeller in the front of the aircraft to disrupt the air flow. These are definite advantages that make the Velocity an attractive addition to the FRL inventory to be used in boundary-layer stability and transition control. Possible mounting locations built into the aircraft for future projects include hard points in the wings and roof of the fuselage. One of the drawbacks of the aircraft is that it has a canard ahead of the main wing that could disrupt the incoming flow for a wing glove or research requiring test pieces mounted to the hard point in the wing. Therefore, it is necessary to understand the influence the canard and the impact of its wake on the wing of the aircraft before any in-depth aerodynamic research could be completed on the aircraft. A combination of in-flight measurements of the canard wake and Computational Fluid Dynamics (CFD) were used to provide a clear picture of the flowfield around the aircraft. The first step of the project consisted of making a 3-D CAD model of the aircraft. This model was then used for the CFD simulations in Fluent. 2-D, 3-D, inviscid, and viscous simulations were preformed on the aircraft. A pressure rake was designed to house a 5-hole probe and 18 Pitot probes that extended forward of the main wing to measure the location and strength of the canard wake at various flight conditions. There were five primary test points that were recorded at multiple times over the course of three flights. Once all of the data were collected from the flights, the freestream conditions became the inputs into the final, 3-D CFD simulations on the aircraft. The good agreement between the CFD results and the in-flight measurements provided the necessary verification of the CFD model of the aircraft. These results can be used in the future planning and execution of experiments involving the Velocity XL-5 RG.

Schouten, Shane Michael

2008-05-01T23:59:59.000Z

242

Abatement of Air Pollution: Hazardous Air Pollutants (Connecticut)  

Energy.gov (U.S. Department of Energy (DOE))

These regulations describe maximum allowable stack concentrations and hazard limiting values for the emission of hazardous air pollutants. The regulations also discuss sampling procedures for...

243

Abatement of Air Pollution: Hazardous Air Pollutants (Connecticut...  

Open Energy Info (EERE)

requirements. Policy Contact Contact Name Anne Gobin Department Department of Energy & Environmental Protection Division Bureau of Air Management Phone (860) 424-3026...

244

Air temperature thresholds for indoor comfort and perceived air quality  

E-Print Network (OSTI)

Moving air for comfort. ASHRAE Journal, May, Arens, E. ,17-22, Copenhagen. . ASHRAE Standard 55- 2010. ThermalSensations of Sedentary Man, ASHRAE Transactions, Vol. 80 (

Zhang, Hui; Edward, Arens; Pasut, Wilmer

2012-01-01T23:59:59.000Z

245

The Velocity of Money in a Life-Cycle Model  

E-Print Network (OSTI)

The determinants of the velocity of money have been examined based on life-cycle hypothesis. The velocity of money can be expressed by reciprocal of the average value of holding time which is defined as interval between participating exchanges for one unit of money. This expression indicates that the velocity is governed by behavior patterns of economic agents and open a way to constructing micro-foundation of it. It is found that time pattern of income and expense for a representative individual can be obtained from a simple version of life-cycle model, and average holding time of money resulted from the individual's optimal choice depends on the expected length of relevant planning periods.

Wang, Y; Wang, Yougui; Qiu, Hanqing

2005-01-01T23:59:59.000Z

246

MACCS2/Deposition Velocity Workshop | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

You are here You are here Home » MACCS2/Deposition Velocity Workshop MACCS2/Deposition Velocity Workshop The Department of Energy's Chief of Nuclear Safety hosted a MACCS2/Deposition Velocity Workshop on June 5-6, 2012, in Germantown, Maryland. Approximately 70 participants attended. The purpose of the workshop was to: Discuss MACCS2 and atmospheric dispersion models as applied to DOE consequence analysis. Discuss implementation of HSS Safety Bulletin 2011-2, Accident Analysis Parameter Update, at field sites. Develop a consistent Department-wide approach for responding to the HSS Safety Bulletin. Identify areas for improved DOE guidance for ensuring defensible consequence analyses. June Workshop Agenda- Final.docx Atmospheric Dispersion Modeling in Safety Analyses; GENII

247

Temporal Velocity Variations beneath the Coso Geothermal Field Observed  

Open Energy Info (EERE)

Velocity Variations beneath the Coso Geothermal Field Observed Velocity Variations beneath the Coso Geothermal Field Observed using Seismic Double Difference Tomography of Compressional and Shear Wave Arrival Times Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Conference Proceedings: Temporal Velocity Variations beneath the Coso Geothermal Field Observed using Seismic Double Difference Tomography of Compressional and Shear Wave Arrival Times Details Activities (1) Areas (1) Regions (0) Abstract: Microseismic imaging can be an important tool for characterizing geothermal reservoirs. Since microseismic sources occur more or less continuously both due to the operations of a geothermal field and the naturally occurring background seismicity, passive seismic monitoring is well suited to quantify the temporal variations in the vicinity of a

248

Determination of the transverse velocity of Q2237+0305  

E-Print Network (OSTI)

The largest systematic uncertainty present in the analysis of gravitationally microlensed quasar light curves is that of the galactic transverse velocity. We describe a method for determining the transverse velocity as well as its application to published monitoring data of Q2237+0305 (Irwin et al. 1989; Corrigan et al. 1991; Ostensen et al 1995). We find that while this data displays strong evidence for microlensing, it limits the transverse velocity to be < 500 km/sec (for microlens masses of 0.5 solar masses). In addition, by combining these results with a new method for modelling the microlensing contribution of stellar proper motions, we find that the masses of microlenses in Q2237+0305 are consistent with those of low mass stars.

J. S. B. Wyithe

1999-09-21T23:59:59.000Z

249

The Velocity Field of Quasar Broad Emission Line Gas  

E-Print Network (OSTI)

In this Letter, the broad emission line (BEL) profiles of superluminal quasars with apparent jet velocities, $\\beta_{a}>10$, (ultraluminal QSOs, or ULQSOs hereafter) are studied as a diagnostic of the velocity field of the BEL emitting gas in quasars. The ULQSOs are useful because they satisfy a very strict kinematical constraint, their parsec scale jets must be propagating within $12^{\\circ}$ of the line of sight. We know the orientation of these objects with great certainty. The large BEL FWHM, $\\sim 3,000 \\mathrm{km/s} - 6,000 \\mathrm{km/s}$, in ULQSOs tend to indicate that the BEL gas has a larger component of axial velocity (either random or in a wind) along the jet direction than previously thought.

Brian Punsly

2007-01-25T23:59:59.000Z

250

Planar velocity analysis of diesel spray shadow images  

E-Print Network (OSTI)

The focus of this work is to demonstrate how spatially resolved image information from diesel fuel injection events can be obtained using a forward-scatter imaging geometry, and used to calculate the velocities of liquid structures on the periphery of the spray. In order to obtain accurate velocities directly from individual diesel spray structures, those features need to be spatially resolved in the measurement. The distributed structures measured in a direct shadowgraphy arrangement cannot be reliably analyzed for this kind of velocity information. However, by utilizing an intense collimated light source and adding imaging optics which modify the signal collection, spatially resolved optical information can be retrieved from spray edge regions within a chosen object plane. This work discusses a set of measurements where a diesel spray is illuminated in rapid succession by two ultrafast laser pulses generated by a mode-locked Ti-Sapphire oscillator seeding a matched pair of regenerative amplifiers. Light fro...

Sedarsky, David

2012-01-01T23:59:59.000Z

251

How Required Reserve Ratio Affects Distribution and Velocity of Money  

E-Print Network (OSTI)

In this paper the dependence of wealth distribution and the velocity of money on the required reserve ratio is examined based on a random transfer model of money and computer simulations. A fractional reserve banking system is introduced to the model where money creation can be achieved by bank loans and the monetary aggregate is determined by the monetary base and the required reserve ratio. It is shown that monetary wealth follows asymmetric Laplace distribution and latency time of money follows exponential distribution. The expression of monetary wealth distribution and that of the velocity of money in terms of the required reserve ratio are presented in a good agreement with simulation results.

Xi, N; Wang, Y; Xi, Ning; Ding, Ning; Wang, Yougui

2005-01-01T23:59:59.000Z

252

Velocity of sound in the relic photon sea  

E-Print Network (OSTI)

We determine the velocity of sound in the blackbody gas of photons and in the gas of relic photons. Derivation is based on the thermodynamic theory of the photon gas and the Einstein relation between energy and mass. The spectral form for the n-dimensional blackbody is derived. The 1D, 2D and 3D blackbody radiation is specified. It is mentioned the possibility of creation of the Mach cone in case that the high energy cosmical particles moves with the speed greater than the velocity of sound in cosmical relic photon sea. Key words: Sound, elasticity, thermodynamics, blackbody, relic photons, Mach's cone.

Pardy, Miroslav

2013-01-01T23:59:59.000Z

253

Velocity of sound in the relic photon sea  

E-Print Network (OSTI)

We determine the velocity of sound in the blackbody gas of photons and in the gas of relic photons. Derivation is based on the thermodynamic theory of the photon gas and the Einstein relation between energy and mass. The spectral form for the n-dimensional blackbody is derived. The 1D, 2D and 3D blackbody radiation is specified. It is mentioned the possibility of creation of the Mach cone in case that the high energy cosmical particles moves with the speed greater than the velocity of sound in cosmical relic photon sea. Key words: Sound, elasticity, thermodynamics, blackbody, relic photons, Mach's cone.

Miroslav Pardy

2013-02-18T23:59:59.000Z

254

Edge Turbulence Velocity Changes with Lithium Coating on NSTX  

SciTech Connect

Lithium coating improves energy confinement and eliminates edge localized modes in NSTX, but the mechanism of this improvement is not yet well understood. We used the gas-puff-imaging (GPI) diagnostic on NSTX to measure the changes in edge turbulence which occurred during a scan with variable lithium wall coating, in order to help understand the reason for the confinement improvement with lithium. There was a small increase in the edge turbulence poloidal velocity and a decrease in the poloidal velocity fluctuation level with increased lithium. The possible effect of varying edge neutral density on turbulence damping was evaluated for these cases in NSTX. __________________________________________________

A. Cao, S.J. Zweben, D.P. Stotler, M. Bell, A. Diallo, S.M. Kaye and B. LeBlanc

2012-08-10T23:59:59.000Z

255

Source shape determination with directional fragment-fragment velocity correlations  

E-Print Network (OSTI)

Correlation functions, constructed from directional projections of the relative velocities of fragments, are used to determine the shape of the breakup volume in coordinate space. For central collisions of 129Xe + natSn at 50 MeV per nucleon incident energy, measured with the 4pi multi-detector INDRA at GSI, a prolate shape aligned along the beam direction with an axis ratio of 1:0.7 is deduced. The sensitivity of the method is discussed in comparison with conventional fragment-fragment velocity correlations.

A. Le Fevre; C. Schwarz; G. Auger; M. L. Begemann-Blaich; N. Bellaize; R. Bittiger; F. Bocage; B. Borderie; R. Bougault; B. Bouriquet; J. L. Charvet; A. Chbihi; R. Dayras; D. Durand; J. D. Frankland; E. Galichet; D. Gourio; D. Guinet; S. Hudan; P. Lautesse; F. Lavaud; R. Legrain; O. Lopez; J. Lukasik; U. Lynen; W. F. J. Mueller; L. Nalpas; H. Orth; E. Plagnol; E. Rosato; A. Saija; C. Sfienti; B. Tamain; W. Trautmann; A. Trzcinski; K. Turzo; E. Vient; M. Vigilante; C. Volant; B. Zwieglinski

2007-11-09T23:59:59.000Z

256

Clutter in the GMTI range-velocity map.  

SciTech Connect

Ground Moving Target Indicator (GMTI) radar maps echo data to range and range-rate, which is a function of a moving target's velocity and its position within the antenna beam footprint. Even stationary clutter will exhibit an apparent motion spectrum and can interfere with moving vehicle detections. Consequently it is very important for a radar to understand how stationary clutter maps into radar measurements of range and velocity. This mapping depends on a wide variety of factors, including details of the radar motion, orientation, and the 3-D topography of the clutter.

Doerry, Armin Walter

2009-04-01T23:59:59.000Z

257

THE RADIAL VELOCITY EXPERIMENT (RAVE): THIRD DATA RELEASE  

Science Conference Proceedings (OSTI)

We present the third data release of the RAdial Velocity Experiment (RAVE) which is the first milestone of the RAVE project, releasing the full pilot survey. The catalog contains 83,072 radial velocity measurements for 77,461 stars in the southern celestial hemisphere, as well as stellar parameters for 39,833 stars. This paper describes the content of the new release, the new processing pipeline, as well as an updated calibration for the metallicity based upon the observation of additional standard stars. Spectra will be made available in a future release. The data release can be accessed via the RAVE Web site.

Siebert, A. [Observatoire Astronomique de Strasbourg, Universite de Strasbourg, CNRS, UMR 7550, 11 rue de l'universite, 67000 Strasbourg (France); Williams, M. E. K.; Siviero, A.; Boeche, C.; Steinmetz, M.; De Jong, R. S.; Enke, H.; Anguiano, B. [Leibniz-Institut fuer Astrophysik Potsdam (AIP), An der Sternwarte 16, D-14482 Potsdam (Germany); Reid, W.; Ritter, A. [Department of Physics and Astronomy, Faculty of Sciences, Macquarie University, NSW 2109, Sydney (Australia); Fulbright, J.; Wyse, R. F. G. [Department of Physics and Astronomy, Johns Hopkins University, 366 Bloomberg Center, 3400 N. Charles St., Baltimore, MD 21218 (United States); Munari, U. [INAF Osservatorio Astronomico di Padova, 36012 Asiago (Italy); Zwitter, T. [Faculty of Mathematics and Physics, University of Ljubljana, Jadranska 19, 1000 Ljubljana (Slovenia); Watson, F. G.; Burton, D.; Cass, C. J. P.; Fiegert, K.; Hartley, M.; Russel, K. S. [Australian Astronomical Observatory, P.O. Box 296, Epping, NSW 1710 (Australia)

2011-06-15T23:59:59.000Z

258

Fermi velocity renormalization and dynamical gap generation in graphene  

E-Print Network (OSTI)

We study the renormalization of the Fermi velocity by the long-range Coulomb interactions between the charge carriers in the Dirac-cone approximation for the effective low-energy description of the electronic excitations in graphene at half filling. Solving the coupled system of Dyson-Schwinger equations for the dressing functions in the corresponding fermion propagator with various approximations for the particle-hole polarization we observe that Fermi velocity renormalization effects generally lead to a considerable increase of the critical coupling for dynamical gap generation and charge-density wave formation at the semimetal-insulator transition.

C. Popovici; C. S. Fischer; L. von Smekal

2013-08-28T23:59:59.000Z

259

Reduce Air Infiltration in Furnaces  

Science Conference Proceedings (OSTI)

This DOE Industrial Technologies Program tip sheet describes how to save energy and costs by reducing air infiltration in industrial furnaces; tips include repairing leaks and increasing insulation.

Not Available

2006-01-01T23:59:59.000Z

260

Oklahoma Clean Air Act (Oklahoma)  

Energy.gov (U.S. Department of Energy (DOE))

This legislation establishes the authority for the Oklahoma Department of Environmental Quality to administer programs to maintain and monitor air quality across Oklahoma. The Department monitors...

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Optimization of Air Conditioning Cycling.  

E-Print Network (OSTI)

??Systems based on the vapor compression cycle are the most widely used in a variety of air conditioning applications. Despite the vast growth of modern (more)

Seshadri, Swarooph

2012-01-01T23:59:59.000Z

262

Air Conditioning | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

environment. An air conditioner uses a cold indoor coil called the evaporator. The condenser, a hot outdoor coil, releases the collected heat outside. The evaporator and...

263

Air Kerma - High Energy Xray  

Science Conference Proceedings (OSTI)

... such as high energy megavoltage x rays with peak voltages of at least 5 MV. Currently, air-kerma measurements at these high energies are not ...

2013-03-13T23:59:59.000Z

264

Reactive Air Aluminization  

DOE Green Energy (OSTI)

Ferritic stainless steels and other alloys are of great interest to SOFC developers for applications such as interconnects, cell frames, and balance of plant components. While these alloys offer significant advantages (e.g., low material and manufacturing cost, high thermal conductivity, and high temperature oxidation resistance), there are challenges which can hinder their utilization in SOFC systems; these challenges include Cr volatility and reactivity with glass seals. To overcome these challenges, protective coatings and surface treatments for the alloys are under development. In particular, aluminization of alloy surfaces offers the potential for mitigating both evaporation of Cr from the alloy surface and reaction of alloy constituents with glass seals. Commercial aluminization processes are available to SOFC developers, but they tend to be costly due to their use of exotic raw materials and/or processing conditions. As an alternative, PNNL has developed Reactive Air Aluminization (RAA), which offers a low-cost, simpler alternative to conventional aluminization methods.

Choi, Jung-Pyung; Chou, Y. S.; Stevenson, Jeffry W.

2011-10-28T23:59:59.000Z

265

Development of an isothermal 2D zonal air volume model with impulse  

NLE Websites -- All DOE Office Websites (Extended Search)

Development of an isothermal 2D zonal air volume model with impulse Development of an isothermal 2D zonal air volume model with impulse conservation Title Development of an isothermal 2D zonal air volume model with impulse conservation Publication Type Conference Paper Year of Publication 2010 Authors Victor, Norrefeldt, Thierry Stephane Nouidui, and Gunnar Gruen Conference Name Clima 2010, 10th Rehva World Congress "Sustainable Energy Use in Buildings" Conference Location Antalya, Turkey Abstract This paper presents a new approach to model air flows with a zonal model. The aim of zonal models is to perform quick simulations of the air distribution in rooms. Therefore an air volume is subdivided into several discrete zones, typically 10 to 100. The zones are connected with flow elements computing the amount of air exchanged between them. In terms of complexity and needed computational time zonal models are a compromise between CFDcalculations and the approximation of perfect mixing. In our approach the air flow velocity is used as property of the zones. Thus the distinction between normal zones and jet or plume influenced zones becomes obsolete. The model is implemented in the object oriented and equation based language Modelica. A drawback of the new formulation is that the calculated flow pattern depends on the discretization. Nevertheless, the results show that the new zonal model performs well and is a useful extension to existing models.

266

Industrial HVAC Air-to-Air Energy Recovery Retrofit Economics  

E-Print Network (OSTI)

Retrofitting air-to-air energy recovery equipment is relatively simply to design and easy to install. Additionally, HVAC energy recovery is almost risk free when compared to process retrofit. Life cycle cost analysis is the best way to illustrate the economic attractiveness of retrofitting HVAC industrial energy recovery equipment.

Graham, E. L.

1980-01-01T23:59:59.000Z

267

Air distribution effectiveness with stratified air distribution systems  

E-Print Network (OSTI)

, Ph.D Qingyan Chen, Ph.D. Student Member ASHRAE Fellow ASHRAE ABSTRACT Stratified air distribution distribution systems has been taken into consideration by the ASHRAE standards through the air distribution effectiveness. For example, Table 6-1 of ANSI/ASHRAE Standard 62.1-2004 (ASHRAE 2004) defines the minimum

Chen, Qingyan "Yan"

268

Air conditioning: Impact on the built environment  

Science Conference Proceedings (OSTI)

The topics discussed in this book are: Introduction. 1. Air Conditioning - An Ever Expanding Market. 2. Building Envelope Design and Air Contitioning. 3. Air Conditioning and Energy - The CIBSE Building Energy Code. 4. Thermal Storage in Air Conditioning Systems. 5. Good Practice in the Design and Construction of Air Conditioning Systems. 6. Software for Air Conditioning Load Analysis and Design. 7. Lloyd's of London - The Architecture of Air Conditioning - Prediction of the Environment.

Sherratt, A.F.C.

1987-01-01T23:59:59.000Z

269

Velocity Autocorrelation Functions and Diffusion of Dusty Plasma  

SciTech Connect

The velocity autocorrelation functions and square displacements were calculated on the basis of experimental data obtained on experimental setup with dc discharge. Computer simulation of the system of dust particles by the method of the Langevin dynamics was performed. The comparisons of experimental and theoretical results are given.

Ramazanov, T. S.; Dzhumagulova, K. N.; Daniyarov, T. T.; Dosbolayev, M. K.; Jumabekov, A. N. [IETP, al-Farabi Kazakh National University, 96a, Tole bi St., Almaty, 050012 (Kazakhstan)

2008-09-07T23:59:59.000Z

270

Velocity-Space Proton Diffusion in the Solar Wind Turbulence  

E-Print Network (OSTI)

We study a velocity-space quasilinear diffusion of the solar wind protons driven by oblique Alfven turbulence at proton kinetic scales. Turbulent fluctuations at these scales possess properties of kinetic Alfven waves (KAWs) that are efficient in Cherenkov resonant interactions. The proton diffusion proceeds via Cherenkov kicks and forms a quasilinear plateau - nonthermal proton tail in the velocity distribution function (VDF). The tails extend in velocity space along the mean magnetic field from 1 to (1.5-3) VA, depending on the spectral break position, turbulence amplitude at the spectral break, and spectral slope after the break. The most favorable conditions for the tail generation occur in the regions where the proton thermal and Alfven velocities are about the same, VTp/VA = 1. The estimated formation times are within 1-2 h for typical tails at 1 AU, which is much shorter than the solar wind expansion time. Our results suggest that the nonthermal proton tails, observed in-situ at all heliocentric distan...

Voitenko, Yuriy

2013-01-01T23:59:59.000Z

271

Seismic imaging for velocity and attenuation structure in geothermal fields  

DOE Green Energy (OSTI)

We have applied the attenuation inversion technique developed by Evans and Zucca (1988) to a seismic tomographic data set taken at Newberry Volcano by Achauer et al. (1988). Our preliminary results suggest that the interpretation of the velocity data by Achauer et al. that a magma chamber is present 3 km beneath the caldera is not confirmed by the attenuation data.

Zucca, J.J. (Lawrence Livermore National Lab., CA (USA)); Evans, J.R. (Geological Survey, Menlo Park, CA (USA))

1989-06-01T23:59:59.000Z

272

Effects of Velocity Shear in Advective Mixed-Layer Models  

Science Conference Proceedings (OSTI)

A general multidimensional model of the upper mixed layer of oceans and lakes is presented. The density profile is approximated as uniform over the depth of the layer. Such an assumption is not made for the distribution of the horizontal velocity ...

Will P. M. de Ruijter

1983-09-01T23:59:59.000Z

273

Measurement of turbulent wind velocities using a rotating boom apparatus  

DOE Green Energy (OSTI)

The present report covers both the development of a rotating-boom facility and the evaluation of the spectral energy of the turbulence measured relative to the rotating boom. The rotating boom is composed of a helicopter blade driven through a pulley speed reducer by a variable speed motor. The boom is mounted on a semiportable tower that can be raised to provide various ratios of hub height to rotor diameter. The boom can be mounted to rotate in either the vertical or horizontal plane. Probes that measure the three components of turbulence can be mounted at any location along the radius of the boom. Special hot-film sensors measured two components of the turbulence at a point directly in front of the rotating blade. By using the probe rotated 90/sup 0/ about its axis, the third turbulent velocity component was measured. Evaluation of the spectral energy distributions for the three components of velocity indicates a large concentration of energy at the rotational frequency. At frequencies slightly below the rotational frequency, the spectral energy is greatly reduced over that measured for the nonrotating case measurements. Peaks in the energy at frequencies that are multiples of the rotation frequency were also observed. We conclude that the rotating boom apparatus is suitable and ready to be used in experiments for developing and testing sensors for rotational measurement of wind velocity from wind turbine rotors. It also can be used to accurately measure turbulent wind for testing theories of rotationally sampled wind velocity.

Sandborn, V.A.; Connell, J.R.

1984-04-01T23:59:59.000Z

274

A fixed complexity velocity estimation method for mobile MIMO users  

Science Conference Proceedings (OSTI)

To estimate speed of a moving user transmitting data over a Single Input Single Output (SISO) Rayleigh fading channels, many Autocorrelation function (ACF) based schemes have been presented in literature [2-7]. Recently, it was shown that in a Multiple ... Keywords: autocorrelation function, complexity reduction, correlated MIMO channels, velocity estimation

Salman A. Khan

2010-01-01T23:59:59.000Z

275

Low inlet gas velocity high throughput biomass gasifier  

DOE Patents (OSTI)

The present invention discloses a novel method of operating a gasifier for production of fuel gas from carbonaceous fuels. The process disclosed enables operating in an entrained mode using inlet gas velocities of less than 7 feet per second, feedstock throughputs exceeding 4000 lbs/ft.sup.2 -hr, and pressures below 100 psia.

Feldmann, Herman F. (Worthington, OH); Paisley, Mark A. (Upper Arlington, OH)

1989-01-01T23:59:59.000Z

276

The relativistic velocity addition law optimizes a forecast gambler's profit  

E-Print Network (OSTI)

We extend the projective covariant bookmaker's bets model to the forecasting gamblers case. The probability of correctness of forecasts shifts probabilities of branching. The formula for the shift of probabilities leads to the velocity addition rule of the special theory of relativity. In the absence of information about bookmaker's wagers the stochastic logarithmic rates completely determines the optimal stakes of forecast gambler.

Piotrowski, Edward W

2007-01-01T23:59:59.000Z

277

The Cartesian Diver: A Self-Profiling Lagrangian Velocity Recorder  

Science Conference Proceedings (OSTI)

The Cartesian diver is an autonomous velocity profiler capable of operating to 1 km depth in the ocean. It has a self-controlled buoyancy changer which is used to control the direction of profiling. The buoyancy changer has two states, full ...

T. F. Duda; C. S. Cox; T. K. Deaton

1988-02-01T23:59:59.000Z

278

Particle velocity measurements of the reaction zone in nitromethane  

DOE Green Energy (OSTI)

The detonation reaction-zone length in neat, deuterated, and chemically sensitized nitromethane (NM) has been measured by using several different laser-based velocity interferometry systems. The experiments involved measuring the particle velocity history at a NM/PMMA (polymethylmethacrylate) window interface during the time a detonation in the NM interacted with the interface. Initially, Fabry-Perot interferometry was used, but, because of low time resolution (>5 ns), several different configurations of VISAR interferometry were subsequently used. Early work was done with VISARs with a time resolution of about 3 ns. By making changes to the recording system, we were able to improve this to {approx}1 ns. Profiles measured at the NM/PMMA interface agree with the ZND theory, in that a spike ({approx}2.45 mm/{micro}s) is measured that is consistent with an extrapolated reactant NM Hugoniot matched to the PMMA window. The spike is rather sharp, followed by a rapid drop in particle velocity over a time of 5 to 10 ns; this is evidence of early fast reactions. Over about 50 ns, a much slower particle velocity decrease occurs to the assumed CJ condition - indicating a total reaction zone length of {approx}300 {micro}m. When the NM is chemically changed, such as replacing the hydrogen atoms with deuterium or chemically sensitizing with a base, some changes are observed in the early part of the reaction zone.

Sheffield, S. A. (Stephen A.); Engelke, R. P. (Raymond P.); Alcon, R. R. (Robert R.); Gustavsen, R. L. (Richard L.); Robbins, D. L. (David L.); Stahl, D. B. (David B.); Stacy, H. L. (Howard L.); Whitehead, M. (Michael)

2002-01-01T23:59:59.000Z

279

Velocity and Stress in the Deep-Ocean Boundary Layer  

Science Conference Proceedings (OSTI)

In order to predict the response of deep ocean sediments to the near-bottom currents, accurate estimates of the near-bottom velocity and the boundary shear stress are necessary. Because of the unsteady nature of deep ocean currents, dynamic ...

S. R. McLean; J. Yean

1987-09-01T23:59:59.000Z

280

Deep ADCP Velocity Measurements in the Gulf Stream  

Science Conference Proceedings (OSTI)

This paper presents observations of the velocity structure from two transects across a Gulf Stream meander near 37N, 68W. Data were collected with a vessel-mounted 75-kHz acoustic Doppler current profiler (ADCP) to a depth of about 700 m. The ...

A. V. Berezutskii; S. E. Maximov; V. E. Sklyarov; R. L. Gordon

1991-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

VSD/VFD Screw air compressor, Kunshan CompAirs Machinery Plant ...  

U.S. Energy Information Administration (EIA)

VSD/VFD Screw air compressor,Kunshan CompAirs Machinery Plant Co.,Ltd is the leading air compressor manufacturer and exporter in china, Professional ...

282

jet-compressible-gas-july25.tex 1 Liquid jet in a high Mach number air stream  

E-Print Network (OSTI)

jet-compressible-gas-july25.tex 1 Liquid jet in a high Mach number air stream T.Funada, D velocity airstream is studied assuming that the flow of the viscous gas and liquid is irrotational for the perturbations which depend on all the material properties of the incompressible liquid and compressible gas

Joseph, Daniel D.

283

Laser sheet light flow visualization for evaluating room air flowsfrom Registers  

SciTech Connect

Forced air heating and cooling systems and whole house ventilation systems deliver air to individual rooms in a house via supply registers located on walls ceilings or floors; and occasionally less straightforward locations like toe-kicks below cabinets. Ideally, the air velocity out of the registers combined with the turbulence of the flow, vectoring of air by register vanes and geometry of register placement combine to mix the supply air within the room. A particular issue that has been raised recently is the performance of multiple capacity and air flow HVAC systems. These systems vary the air flow rate through the distribution system depending on the system load, or if operating in a ventilation rather than a space conditioning mode. These systems have been developed to maximize equipment efficiency, however, the high efficiency ratings do not include any room mixing effects. At lower air flow rates, there is the possibility that room air will be poorly mixed, leading to thermal stratification and reduced comfort for occupants. This can lead to increased energy use as the occupants adjust the thermostat settings to compensate and parts of the conditioned space have higher envelope temperature differences than for the well mixed case. In addition, lack of comfort can be a barrier to market acceptance of these higher efficiency systems To investigate the effect on room mixing of reduced air flow rates requires the measurement of mixing of supply air with room air throughout the space to be conditioned. This is a particularly difficult exercise if we want to determine the transient performance of the space conditioning system. Full scale experiments can be done in special test chambers, but the spatial resolution required to fully examine the mixing problem is usually limited by the sheer number of thermal sensors required. Current full-scale laboratory testing is therefore severely limited in its resolution. As an alternative, we used a water-filled scale model of a room in which whole-field supply air mixing maps of two vertical planes were measured using a Planar Laser-Induced Fluorescence (PLIF) measurement technique. Water marked with fluorescent dye was used to simulate the supply airflow; and the resulting concentrations within the water filled model show how the supply air mixes with the room air and are an analog for temperature (for thermal loads) or fresh air (for ventilation). In addition to performing experiments over a range of flow rates, we also changed register locations and examined the effects for both heating and cooling operation by changing the water density (simulating air density changes due to temperature changes) using dissolved salt.

Walker, Iain S.; Claret, Valerie; Smith, Brian

2006-04-01T23:59:59.000Z

284

Velocity and Attenuation Structure of the Geysers Geothermal Field, California  

DOE Green Energy (OSTI)

The Geysers geothermal field is located in northern California and is one of the world's largest producers of electricity from geothermal energy. The resource consists of primarily dry steam which is produced from a low, porosity fractured graywacke. Over the last several years steam pressure at the Geysers has been dropping. Concern over decline of the resource has prompted research to understand its fundamental nature. A key issue is the distribution of fluid in the matrix of the reservoir rock. In this paper we interpret seismic compressional-wave velocity and attenuation data at the Geysers in terms of the geologic structure and fluid saturation in the reservoir. Our data consist of approximately 300 earthquakes that are of magnitude 1.2 and are distributed in depth between sea level and 2.5 km. Using compressional-wave arrival times, we invert for earthquake location, origin time, and velocity along a three-dimensional grid. Using the initial pulse width of the compressional-wave, we invert for the initial pulse width associated with the source, and the one-dimensional Q structure. We find that the velocity structure correlates with known mapped geologic units, including a velocity high that is correlated with a felsite body at depth that is known from drilling. The dry steam reservoir, which is also known from drilling, is mostly correlated with low velocity. The Q increases with depth to the top of the dry steam reservoir and decreases with depth within the reservoir. The decrease of Q with depth probably indicates that the saturation of the matrix of the reservoir rock increases with depth.

Zucca, J. J.; Hutchings, L. J.; Kasameyer, P. W.

1993-01-01T23:59:59.000Z

285

Low Velocity Sphere Impact of a Soda Lime Silicate Glass  

SciTech Connect

This report summarizes TARDEC-sponsored work at Oak Ridge National Laboratory (ORNL) during the FY11 involving low velocity (< 30 m/s or < 65 mph) ball impact testing of Starphire soda lime silicate glass. The intent was to better understand low velocity impact response in the Starphire for sphere densities that bracketed that of rock. Five sphere materials were used: borosilicate glass, soda-lime silicate glass, steel, silicon nitride, and alumina. A gas gun was fabricated to produce controlled velocity delivery of the spheres against Starphire tile targets. Minimum impact velocities to initiate fracture in the Starphire were measured and interpreted in context to the kinetic energy of impact and the elastic property mismatch between the any of the five sphere-Starphire-target combinations. The primary observations from this low velocity (< 30 m/s or < 65 mph) testing were: (1) Frictional effects contribute to fracture initiation. (2) Spheres with a lower elastic modulus require less force to initiate fracture in the Starphire than spheres with a higher elastic modulus. (3) Contact-induced fracture did not initiate in the Starphire SLS for impact kinetic energies < 150 mJ. Fracture sometimes initiated or kinetic energies between {approx} 150-1100 mJ; however, it tended to occur when lower elastic modulus spheres were impacting it. Contact-induced fracture would always occur for impact energies > 1100 mJ. (4) The force necessary to initiate contact-induced fracture is higher under dynamic or impact conditions than it is under quasi-static indentation conditions. (5) Among the five used sphere materials, silicon nitride was the closest match to 'rock' in terms of both density and (probably) elastic modulus.

Wereszczak, Andrew A [ORNL; Fox, Ethan E [ORNL; Morrissey, Timothy G [ORNL; Vuono, Daniel J [ORNL

2011-10-01T23:59:59.000Z

286

Protective supplied breathing air garment  

DOE Patents (OSTI)

A breathing air garment is disclosed for isolating a wearer from hostile environments containing toxins or irritants includes a suit and a separate head protective enclosure or hood engaging a suit collar in sealing attachment. The hood and suit collar are cylindrically shaped and dimensioned to enable the wearer to withdraw his hands from the suit sleeves to perform manual tasks within the hood interior. Breathing air is supplied from an external air line with an air delivery hose attached to the hood interior. The hose feeds air into an annular halo-like fiber-filled plenum having spaced discharge orifices attached to the hood top wall. A plurality of air exhaust/check valves located at the suit extremities cooperate with the hood air delivery system to provide a cooling flow of circulating air from the hood throughout the suit interior. A suit entry seal provided on the suit rear torso panel permits access into the suit and is sealed with an adhesive sealing flap. 17 figs.

Childers, E.L.; Hortenau, E.F. von.

1984-07-10T23:59:59.000Z

287

Protective supplied breathing air garment  

DOE Patents (OSTI)

A breathing air garment for isolating a wearer from hostile environments containing toxins or irritants includes a suit and a separate head protective enclosure or hood engaging a suit collar in sealing attachment. The hood and suit collar are cylindrically shaped and dimensioned to enable the wearer to withdraw his hands from the suit sleeves to perform manual tasks within the hood interior. Breathing air is supplied from an external air line with an air delivery hose attached to the hood interior. The hose feeds air into an annular halo-like fiber-filled plenum having spaced discharge orifices attached to the hood top wall. A plurality of air exhaust/check valves located at the suit extremities cooperate with the hood air delivery system to provide a cooling flow of circulating air from the hood throughout the suit interior. A suit entry seal provided on the suit rear torso panel permits access into the suit and is sealed with an adhesive sealing flap.

Childers, Edward L. (Lakewood, CO); von Hortenau, Erik F. (Golden, CO)

1984-07-10T23:59:59.000Z

288

The Clean Air Mercury Rule  

SciTech Connect

Coming into force on July 15, 2005, the US Clean Air Mercury Rule will use a market-based cap-and-trade approach under Section 111 of the Clean Air Act to reduce mercury emissions from the electric power sector. This article provides a comprehensive summary of the new rule. 14 refs., 2 tabs.

Michael Rossler [Edison Electric Institute, Washington, DC (US)

2005-07-01T23:59:59.000Z

289

air conditioner | OpenEI  

Open Energy Info (EERE)

air conditioner air conditioner Dataset Summary Description View 2010 energy efficiency data from AeroSys Inc, Coaire, Cold Point, First Operations, LG Electronics, Nordyne, and Quietside manufacturers. Data includes cooling capacity, cooling performance, heating capacity, and heating performance. Spreadsheet was created by combining the tables in pdf files that are included in the zip file. Source Energy Applicance Data - United States Federal Trade Commission, www.ftc.gov Date Released Unknown Date Updated Unknown Keywords air conditioner central air conditioner efficiency efficient energy heat pump Data application/vnd.ms-excel icon 2010_CentralAC_All.xls (xls, 82.4 KiB) application/zip icon 2010CentralAirConditioner.zip (zip, 398.2 KiB) Quality Metrics Level of Review Some Review

290

Air Force Renewable Energy Programs  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 1 Ken Gray P.E. HQ AFCESA /CENR Air Force Renewable Energy Programs April, 2011 FUPWG "Make Energy a Consideration in All We Do" I n t e g r i t y - S e r v i c e - E x c e l l e n c e THINK GREEN, BUILD GREEN, Topics  Air Force Energy Use  Air Force Facility Energy Center  Current RE Generation  Project Development System  Programmed RE Generation FY11-13  Goal Achievement 2 I n t e g r i t y - S e r v i c e - E x c e l l e n c e THINK GREEN, BUILD GREEN, Air Force 2010 Energy Use The Air Force spent approximately $8.2 billion for energy in 2010; an increase of 22% from 2009 Energy Cost and Consumption Trends Energy Cost Breakdown Aviation 79% Facilities 17% 3 Aviation 84% Facilities 12% Vehicles & Equipment

291

High Efficiency Particulate Air Filters  

NLE Websites -- All DOE Office Websites (Extended Search)

High Efficiency Particulate Air (HEPA) Filters High Efficiency Particulate Air (HEPA) Filters Home Standards DOE Workshops Nuclear Air Cleaning Conference Proceedings Qualified Filter List News Items Related Sites HEPA Related Lessons Learned Contact Us HSS Logo High Efficiency Particulate Air Filters The HEPA Filter web site provides a forum for informing and reporting department-wide activities related to filtration and ventilation issues with special reference to the High Efficiency Particulate Air (HEPA) Filters' use, inspection, and testing. This site contains essentials of DOE HEPA filter test program, procedures, requirements and quality assurance aspects applicable to HEPA filters used in DOE facilities. This site contains information about the DOE-accepted Filter Test Facility and its management, operation and quality assuranceprogram.

292

NETL: IEP - Air Quality Research  

NLE Websites -- All DOE Office Websites (Extended Search)

Home > Technologies > Coal & Power Systems > Innovations for Existing Plants > Air Quality Research Home > Technologies > Coal & Power Systems > Innovations for Existing Plants > Air Quality Research Innovations for Existing Plants Air Quality Research Ambient Monitoring Emissions Characterization Predictive Modeling & Evaluation Health Effects Regulatory Drivers Air Quality Research Reference Shelf The NETL Air Quality Research program is designed to resolve the scientific uncertainties associated with the atmospheric formation, distribution, and chemical transformation of pollutant emissions from today's coal-fired power plants, and to obtain a realistic assessment of the human health impacts of these emissions. Results of this research will help the DOE Office of Fossil Energy address policy questions regarding coal plant emissions and provide guidance for future emissions control R&D programs at

293

Powdered coal air dispersion nozzle  

SciTech Connect

An improved coal/air dispersion nozzle introduces fuel into the combustion chamber of a gas turbine engine as a finely atomized, dispersed spray for a uniform combustion. The nozzle has an inlet that receives finely powdered coal from a coal transport or coal/air fluidizer system and a scroll swirl generator is included within the nozzle to swirl a fluidized coal/air mixture supplied to the inlet of the nozzle. The scroll is in the form of a thin, flat metal sheet insert, twisted along its length, and configured to prevent build-up of coal particles within the nozzle prior to ejection from its outlet. Airblast air jets are included along the length of the nozzle body to assist in the discharge of the fluidized coal from the nozzle outlet and an angular pintle tip overlies the outlet to redirect coal/air mixture through a desired fluidized coal spray angle.

Kosek, T.P.; Steinhilper, E.A.

1981-10-27T23:59:59.000Z

294

Reduce Air Infiltration in Furnaces (English/Chinese) (Fact Sheet)  

Science Conference Proceedings (OSTI)

Chinese translation of the Reduce Air Infiltration in Furnaces fact sheet. Provides suggestions on how to improve furnace energy efficiency. Fuel-fired furnaces discharge combustion products through a stack or a chimney. Hot furnace gases are less dense and more buoyant than ambient air, so they rise, creating a differential pressure between the top and the bottom of the furnace. This differential, known as thermal head, is the source of a natural draft or negative pressure in furnaces and boilers. A well-designed furnace (or boiler) is built to avoid air leakage into the furnace or leakage of flue gases from the furnace to the ambient. However, with time, most furnaces develop cracks or openings around doors, joints, and hearth seals. These openings (leaks) usually appear small compared with the overall dimensions of the furnace, so they are often ignored. The negative pressure created by the natural draft (or use of an induced-draft fan) in a furnace draws cold air through the openings (leaks) and into the furnace. The cold air becomes heated to the furnace exhaust gas temperature and then exits through the flue system, wasting valuable fuel. It might also cause excessive oxidation of metals or other materials in the furnaces. The heat loss due to cold air leakage resulting from the natural draft can be estimated if you know four major parameters: (1) The furnace or flue gas temperature; (2) The vertical distance H between the opening (leak) and the point where the exhaust gases leave the furnace and its flue system (if the leak is along a vertical surface, H will be an average value); (3) The area of the leak, in square inches; and (4) The amount of operating time the furnace spends at negative pressure. Secondary parameters that affect the amount of air leakage include these: (1) The furnace firing rate; (2) The flue gas velocity through the stack or the stack cross-section area; (3) The burner operating conditions (e.g., excess air, combustion air temperature, and so on). For furnaces or boilers using an induced-draft (ID) fan, the furnace negative pressure depends on the fan performance and frictional losses between the fan inlet and the point of air leakage. In most cases, it would be necessary to measure or estimate negative pressure at the opening. The amount of air leakage, the heat lost in flue gases, and their effects on increased furnace or boiler fuel consumption can be calculated by using the equations and graphs given in Industrial Furnaces (see W. Trinks et al., below). Note that the actual heat input required to compensate for the heat loss in flue gases due to air leakage would be greater than the heat contained in the air leakage because of the effect of available heat in the furnace. For a high-temperature furnace that is not maintained properly, the fuel consumption increase due to air leakage can be as high as 10% of the fuel input.

Not Available

2011-10-01T23:59:59.000Z

295

Prediction of Air Mixing From High Sidewall Diffusers in Cooling Mode: Preprint  

Science Conference Proceedings (OSTI)

Computational fluid dynamics modeling was used to evaluate the performance of high sidewall air supply in cooling mode. The research focused on the design, placement, and operation of air supply diffusers located high on a sidewall and return grilles located near the floor on the same sidewall. Parameters of the study are the supply velocity, supply temperature, diffuser dimensions and room dimensions. Thermal loads characteristic of high performance homes were applied at the walls and room temperature was controlled via a thermostat. The results are intended to provide information to guide the selection of high sidewall supply diffusers to provide proper room mixing for cooling of high performance homes.

Ridouane, E. H.; Gawlik, K.

2011-02-01T23:59:59.000Z

296

Velocity distribution of high-energy particles and the solar neutrino problem  

E-Print Network (OSTI)

High energy infers high velocity and high velocity is a concept of special relativity. The Maxwellian velocity distribution is corrected to be consistent with special relativity. The corrected distribution reduces to the Maxwellian distribution for small velocities, contains a relatively depleted high-energy tail and vanishes at the velocity of light. This corrected distribution will lower solar neutrino fluxes and change solar neutrino energy spectra but keep solar sound speeds.

Jian-Miin Liu

2001-08-18T23:59:59.000Z

297

Demonstration of the Cold Air Velocity Technique to Control Fly Ash Erosion at the Endesa Teruel Plant  

Science Conference Proceedings (OSTI)

Boiler tube failures are the leading cause of availability loss and forced outages in fossil plants worldwide. Fly ash erosion (FAE) is one of the top three failure mechanisms. This report demonstrates the procedure used to select a baffle system for reducing FAE in Unit 3 of the Teruel power plant of Endesa in Spain.

2011-11-29T23:59:59.000Z

298

NETL: Water-Energy Interface - Improvement to Air2Air Technology...  

NLE Websites -- All DOE Office Websites (Extended Search)

cooling tower with relatively drier and cooler ambient air. This is done in an air-to-air heat exchanger made up of plastic sheets with two discreet air pathways. As the warm,...

299

Double Ended Guillotine Break in a Prismatic Block VHTR Lower Plenum Air Ingress Scenario  

E-Print Network (OSTI)

The double ended guillotine break leading to density-driven air ingress has been identified as a low probability yet high consequence event for Very High Temperature Reactor (VHTR). The lower plenum of the VHTR contains the core support structure and is composed of graphite. During an air ingress event, oxidation of the graphite structure under high temperature conditions in an oxygen containing environment could degrade the integrity of the core support structure. Following this large break, air from the reactor containment will begin to enter the lower plenum via two mechanisms: diffusion or density driven stratified flow. The large difference in time scales between the mechanisms leads to the need to perform high fidelity experimental studies to investigate the dominant the air ingress mechanism. A scaled test facility has been designed and built that allows the acquisition of velocity measurements during stratification after a pipe break. A non-intrusive optical measurement technique provides full-field velocity measurements profiles of the two species Particle Image Velocimetry (PIV). The data allow a more developed understanding of the fundamental flow features, the development of improved models, and possible mitigation strategies in such a scenario.Two brine-water experiments were conducted with different break locations. Flow fronts were analyzed and findings concluded that the flow has a constant speed through the pipe after the initial lock exchange. The time in which the flow enters the lower plenum is an important factor because it provides the window of opportunity for mitigation strategies in an actual reactor scenario. For both cases the flow of the heavier density liquid (simulating air ingress from the reactor containment) from the pipe enters the reactor vessel in under 6 seconds. The diffusion velocity and heavy flow front of the stratified flow layer were compared for the SF6/He gas case. It is seen that the diffusion plays less of a role as the transport mechanism in comparison to the density-driven stratified flow since the velocity of the diffusion is two orders of magnitude smaller than the velocity of the stratified flow mechanism. This is the reason for the need for density-driven stratified flow investigations following a LOCA. These investigations provided high-quality data for CFD validation in order for these models to depict the basic phenomena occurring in an air ingress scenario.

Hartley, Jessica

2011-08-01T23:59:59.000Z

300

Analysis of Efficiency Standards for Air Conditioners, Air ...  

U.S. Energy Information Administration (EIA)

Federal agencies to select ENERGY STAR and ... analyze the proposed air conditioner and heat pump standards, a new baseline ... square foot office building 0.4 to 0.8 ...

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Low Velocity Sphere Impact of a Soda Lime Silicate Glass  

Science Conference Proceedings (OSTI)

This report summarizes TARDEC-sponsored work at Oak Ridge National Laboratory (ORNL) during the FY11 involving low velocity (energy of impact and the elastic property mismatch between the any of the five sphere-Starphire-target combinations. The primary observations from this low velocity (energies energies between {approx} 150-1100 mJ; however, it tended to occur when lower elastic modulus spheres were impacting it. Contact-induced fracture would always occur for impact energies > 1100 mJ. (4) The force necessary to initiate contact-induced fracture is higher under dynamic or impact conditions than it is under quasi-static indentation conditions. (5) Among the five used sphere materials, silicon nitride was the closest match to 'rock' in terms of both density and (probably) elastic modulus.

Wereszczak, Andrew A [ORNL; Fox, Ethan E [ORNL; Morrissey, Timothy G [ORNL; Vuono, Daniel J [ORNL

2011-10-01T23:59:59.000Z

302

Velocity and density spectra of the Small Magellanic Cloud  

E-Print Network (OSTI)

This paper reports results on the statistical analysis of HI turbulence in the Small Magellanic Cloud (SMC). We use 21 cm channel maps, obtained with the Australia Telescope Compact Array and the Parkes telescope, and analyze the spectrum of observed intensity fluctuations as a function of the velocity slice thickness. We confirm predictions by Lazarian & Pogosyan (2000) on the change of the power law index and establish the spectra of 3-D density and velocity. The obtained spectral indices, -3.3 and -3.4, are slightly more shallow than the predictions for the Kolmogorov spectrum. This contrasts to the predictions for the shock-type spectra that are steeper than the Kolmogorov one. The nature of the energy injection in the SMC is unclear as no distinct energy injection scales are observed up to the entire scale of the SMC.

S. Stanimirovi?; A. Lazarian

2001-02-11T23:59:59.000Z

303

The AMS-RICH velocity and charge reconstruction  

E-Print Network (OSTI)

The AMS detector, to be installed on the International Space Station, includes a Ring Imaging Cerenkov detector with two different radiators, silica aerogel (n=1.05) and sodium fluoride (n=1.334). This detector is designed to provide very precise measurements of velocity and electric charge in a wide range of cosmic nuclei energies and atomic numbers. The detector geometry, in particular the presence of a reflector for acceptance purposes, leads to complex Cerenkov patterns detected in a pixelized photomultiplier matrix. The results of different reconstruction methods applied to test beam data as well as to simulated samples are presented. To ensure nominal performances throughout the flight, several detector parameters have to be carefully monitored. The algorithms developed to fulfill these requirements are presented. The velocity and charge measurements provided by the RICH detector endow the AMS spectrometer with precise particle identification capabilities in a wide energy range. The expected performances on light isotope separation are discussed.

F. Barao; M. Aguilar-Benitez; L. Arruda; B. Baret; A. Barrau; G. Barreira; E. Belmont; J. Berdugo; J. Borges; M. Buenerd; D. Casadei; J. Casaus; E. Cortina; M. Costado; D. Crespo; C. Delgado; C. Diaz; L. Derome; P. Goncalves; R. Garcia-Lopez; C. de la Guia; A. Herrero; E. Lanciotti; G. Laurenti; A. Malinin; C. Mana; J. Marin; M. Mangin-Brinet; G. Martinez; A. Menchaca-Rocha; C. Palomares; R. Pereira; M. Pimenta; A. Putze; Y. Sallaz-Damaz; E. S. Seo; I. Sevilla; A. Torrento; M. Vargas-Trevino; O. Veziant

2007-09-13T23:59:59.000Z

304

Central Air Conditioning | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Central Air Conditioning Central Air Conditioning Central Air Conditioning May 30, 2012 - 8:01pm Addthis Central air conditioners circulate cool air through a system of supply and return ducts. | Photo courtesy of ©iStockphoto/DonNichols. Central air conditioners circulate cool air through a system of supply and return ducts. | Photo courtesy of ©iStockphoto/DonNichols. What does this mean for me? Central air conditioning systems are thermostatically controlled and convenient to use. Central air conditioning systems must be installed properly to operate efficiently. Central air conditioning systems can share ductwork with your heating system. Central air conditioners circulate cool air through a system of supply and return ducts. Supply ducts and registers (i.e., openings in the walls,

305

Tips: Sealing Air Leaks | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Sealing Air Leaks Sealing Air Leaks Tips: Sealing Air Leaks May 16, 2013 - 5:03pm Addthis Sources of Air Leaks in Your Home. Areas that leak air into and out of your home cost you a lot of money. The areas listed in the illustration are the most common sources of air leaks. Sources of Air Leaks in Your Home. Areas that leak air into and out of your home cost you a lot of money. The areas listed in the illustration are the most common sources of air leaks. Air leaks can waste a lot of your energy dollars. One of the quickest energy-- and money-saving tasks you can do is caulk, seal, and weather strip all seams, cracks, and openings to the outside. Tips for Sealing Air Leaks Test your home for air tightness. On a windy day, carefully hold a lit incense stick or a smoke pen next to your windows, doors, electrical

306

Tips: Sealing Air Leaks | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Tips: Sealing Air Leaks Tips: Sealing Air Leaks Tips: Sealing Air Leaks May 16, 2013 - 5:03pm Addthis Sources of Air Leaks in Your Home. Areas that leak air into and out of your home cost you a lot of money. The areas listed in the illustration are the most common sources of air leaks. Sources of Air Leaks in Your Home. Areas that leak air into and out of your home cost you a lot of money. The areas listed in the illustration are the most common sources of air leaks. Air leaks can waste a lot of your energy dollars. One of the quickest energy-- and money-saving tasks you can do is caulk, seal, and weather strip all seams, cracks, and openings to the outside. Tips for Sealing Air Leaks Test your home for air tightness. On a windy day, carefully hold a lit incense stick or a smoke pen next to your windows, doors, electrical

307

Room Air Conditioners | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Room Air Conditioners Room Air Conditioners Room Air Conditioners July 1, 2012 - 5:35pm Addthis A window air conditioner is one solution to cooling part of a house. | Photo courtesy of ©iStockphoto/kschulze. A window air conditioner is one solution to cooling part of a house. | Photo courtesy of ©iStockphoto/kschulze. What does this mean for me? Room air conditioners are less expensive and disruptive to install than central air conditioning systems. Room air conditioners can be a cost-effective alternative to central air conditioning systems. How does it work? Room air conditioners work by cooling one part of your home. Room or window air conditioners cool rooms rather than the entire home or business. If they provide cooling only where they're needed, room air conditioners are less expensive to operate than central units, even though

308

SolarAire LLC | Open Energy Information  

Open Energy Info (EERE)

SolarAire LLC Place Folsom, California Sector Solar Product Developing a solar thermal air conditioning unit. References SolarAire LLC1 LinkedIn Connections CrunchBase Profile...

309

DunoAir | Open Energy Information  

Open Energy Info (EERE)

DunoAir Jump to: navigation, search Name DunoAir Place Hessen, Germany Zip 6865 VX Sector Wind energy Product Doorwerth-based wind project developer. References DunoAir1 LinkedIn...

310

Superluminal group velocity through near-maximal neutrino oscillations  

E-Print Network (OSTI)

Recently it was suggested that the observation of superluminal neutrinos by the OPERA collaboration may be due to group velocity effects resulting from close-to-maximal oscillation between neutrino mass eigenstates, in analogy to known effects in optics. We show that superluminal propagation does occur through this effect for a series of very narrow energy ranges, but this phenomenum cannot explain the OPERA measurement.

Tim R. Morris

2011-10-11T23:59:59.000Z

311

Experimental Evaluation of a Downsized Residential Air Distribution System: Comfort and Ventilation Effectiveness  

SciTech Connect

Good air mixing not only improves thermal comfort Human thermal comfort is the state of mind that expresses satisfaction with the surrounding environment, according to ASHRAE Standard 55. Achieving thermal comfort for most occupants of buildings or other enclosures is a goal of HVAC design engineers. but also enhances ventilation effectiveness by inducing uniform supply-air diffusion. In general, the performance of an air distribution system in terms of comfort and ventilation effectiveness is influenced by the supply air temperature, velocity, and flow rate, all of which are in part dictated by the HVAC (Heating Ventilation Air Conditioning) In the home or small office with a handful of computers, HVAC is more for human comfort than the machines. In large datacenters, a humidity-free room with a steady, cool temperature is essential for the trouble-free system as well as the thermal load attributes. Any potential deficiencies associated with these design variables can be further exacerbated by an improper proximity of the supply and return outlets with respect to the thermal and geometrical characteristics of the indoor space. For high-performance houses, the factors influencing air distribution performance take on an even greater significance because of a reduced supply-air design flow rate resulting from downsized HVAC systems.

Jalalzadeh-Azar, A. A.

2007-01-01T23:59:59.000Z

312

Indoor air radon  

SciTech Connect

This review concerns primarily the health effects that result from indoor air exposure to radon gas and its progeny. Radon enters homes mainly from the soil through cracks in the foundation and other holes to the geologic deposits beneath these structures. Once inside the home the gas decays (half-life 3.8 d) and the ionized atoms adsorb to dust particles and are inhaled. These particles lodge in the lung and can cause lung cancer. The introduction to this review gives some background properties of radon and its progeny that are important to understanding this public health problem as well as a discussion of the units used to describe its concentrations. The data describing the health effects of inhaled radon and its progeny come both from epidemiological and animal studies. The estimates of risk from these two data bases are consistent within a factor of two. The epidemiological studies are primarily for hard rock miners, although some data exist for environmental exposures. The most complete studies are those of the US, Canadian, and Czechoslovakian uranium miners. Although all studies have some deficiencies, those of major importance include uranium miners in Saskatchewan, Canada, Swedish iron miners, and Newfoundland fluorspar miners. These six studies provide varying degrees of detail in the form of dose-response curves. Other epidemiological studies that do not provide quantitative dose-response information, but are useful in describing the health effects, include coal, iron ore and tin miners in the UK, iron ore miners in the Grangesburg and Kiruna, Sweden, metal miners in the US, Navajo uranium miners in the US, Norwegian niobian and magnitite miners, South African gold and uranium miners, French uranium miners, zinc-lead miners in Sweden and a variety of small studies of environmental exposure. An analysis of the epidemiological studies reveals a variety of interpretation problem areas.172 references.

Cothern, C.R.

1990-01-01T23:59:59.000Z

313

Shear wave velocities from noise correlation at local scale  

Science Conference Proceedings (OSTI)

Cross correlations of ambient seismic noise recordings have been studied to infer shear seismic velocities with depth. Experiments have been done in the crowded and noisy historical centre of Napoli over inter-station distances from 50 m to about 400 m, whereas active seismic spreadings are prohibitive, even for just one receiver. Group velocity dispersion curves have been extracted with FTAN method from the noise cross correlations and then the non linear inversion of them has resulted in Vs profiles with depth. The information of near by stratigraphies and the range of Vs variability for samples of Neapolitan soils and rocks confirms the validity of results obtained with our expeditious procedure. Moreover, the good comparison of noise H/V frequency of the first main peak with 1D and 2D spectral amplifications encourages to continue experiments of noise cross-correlation. If confirmed in other geological settings, the proposed approach could reveal a low cost methodology to obtain reliable and detailed Vs velocity profiles.

De Nisco, G.; Nunziata, C. [Dipartimento di Scienze della Terra, Univ. Napoli Federico II (Italy); Vaccari, F. [Dipartimento di Scienze della Terra, Univ. Trieste (Italy); Panza, G. F. [Dipartimento di Scienze della Terra, Univ. Trieste (Italy); The Abdus Salam International Center for Theoretical Physics, ESP-SAND Group, Trieste (Italy)

2008-07-08T23:59:59.000Z

314

Fermi velocity renormalization and the excitonic insulator in graphene  

E-Print Network (OSTI)

We compute the Fermi velocity of the Dirac quasiparticles in clean graphene at the charge neutrality point for strong Coulomb coupling alpha_g. We perform a Lattice Monte Carlo calculation within the low-energy Dirac theory, which includes an instantaneous, long-range Coulomb interaction. This method is non-perturbative and takes full account of quantum fluctuations. We find a finite renormalized Fermi velocity v_FR > v_F, where v_F = c/300. We introduce the critical Fermi velocity renormalization v_c = v_FR(alpha_gc)/v_F, where alpha_gc is the critical coupling for the semimetal-insulator transition due to excitonic pair formation. We compare our results with empirical studies of interaction-induced spectral changes in graphene. We find v_c = 3.3, which should be contrasted with v_FR/v_F = 2 - 3 for ultra-clean suspended graphene and v_FR/v_F = 1.2 for graphene on a boron nitride substrate. Our results are consistent with the non-observation of insulating states in suspended graphene in the absence of an external magnetic field. We also discuss the dynamical critical exponent z.

Joaqun E. Drut; Timo A. Lhde

2013-04-05T23:59:59.000Z

315

Liftoff and blowoff of a diffusion flame between parallel streams of fuel and air  

SciTech Connect

A numerical analysis is presented to describe the liftoff and blowoff of a diffusion flame in the mixing layer between two parallel streams of fuel (mainly methane diluted with nitrogen) and air emerging from porous walls. The analysis, which takes into account the effects of thermal expansion, assumes a one-step overall Arrhenius reaction, where the activation energy E is allowed to vary to reproduce the variations of the planar flame propagation velocity with the equivalence ratio. First, we describe the steady flame-front structure when stabilized close to the porous wall (attached flame regime). Then, we analyze the case where the flame front is located far away from the porous wall, at a distance x{sub f}' such that, upstream of the flame front, the mixing layer has a self-similar structure (lifted flame regime). For steady lifted flames, the results, given here in the case when the fuel and air streams are injected with the same velocity, relate U{sub f}'/S{sub L}, the front velocity (relative to the upstream flow) measured with the planar stoichiometric flame velocity, with the Damkohler number D{sub m}=({delta}{sub m}/{delta}{sub L}){sup 2}, based on the thickness, {delta}{sub m}, of the nonreacting mixing layer at the flame-front position and the laminar flame thickness, {delta}{sub L}. For large values of D{sub m}, the results, presented here for a wide range of dilutions of the fuel stream, provide values of the front propagation velocity that are in good agreement with previous experimental results, yielding well-defined conditions for blowoff. The calculated flame-front velocity can also be used to describe the transient flame-front dynamics after ignition by an external energy source.

Fernandez-Tarrazo, Eduardo [I.N.T.A. Area de Propulsion-Edificio R02, Ctra. Ajalvir, km 4, 28850 Torrejon de Ardoz, Madrid (Spain); Vera, Marcos [Area de Mecanica de Fluidos, Universidad Carlos III de Madrid, 28911 Leganes (Spain); Linan, Amable [Departamento de Motopropulsion y Termofluidodinamica, Universidad Politecnica de Madrid, Pza. Cardenal Cisneros 3, 28040 Madrid (Spain)

2006-01-01T23:59:59.000Z

316

buy vsd air compressor - high quality Manufacturers,Suppliers ...  

U.S. Energy Information Administration (EIA)

vsd air compressor trade offers directory and vsd air compressor business offers list. Trade leads from vsd air compressor Suppliers and vsd air ...

317

Rooftop Unitary Air Conditioner with Integral Dedicated Outdoor Air System  

SciTech Connect

Energy use of rooftop and other unitary air-conditioners in commercial applications accounts for about 1 quad (10{sup 15} Btu) of primary energy use annually in the U.S. [Reference 7]. The realization that this cooling equipment accounts for the majority of commercial building cooled floorspace and the majority also of commercial building energy use has spurred development of improved-efficiency equipment as well as development of stricter standards addressing efficiency levels. Another key market driver affecting design of rooftop air-conditioning equipment has been concern regarding comfort and the control of humidity. Trends for increases in outdoor air ventilation rates in certain applications, and the increasing concern about indoor air quality problems associated with humidity levels and moisture in buildings points to a need for improved dehumidification capability in air-conditioning equipment of all types. In many cases addressing this issue exacerbates energy efficiency, and vice versa. The integrated dedicated outdoor air system configuration developed in this project addresses both energy and comfort/humidity issues.

Tiax Llc

2006-02-28T23:59:59.000Z

318

Indoor Air Quality and Volatile Organic Compounds  

Science Conference Proceedings (OSTI)

... The unit was sized to comply with the outdoor air requirements in ASHRAE Standard 62.2 Ventilation and Acceptable Indoor Air Quality in Low ...

2013-03-12T23:59:59.000Z

319

Aire Valley Environmental | Open Energy Information  

Open Energy Info (EERE)

search Name Aire Valley Environmental Place United Kingdom Product Leeds-based waste-to-energy project developer. References Aire Valley Environmental1 LinkedIn...

320

Radionuclide Air Emission Report for 2011  

E-Print Network (OSTI)

LBNL-470E-201 Radionuclide Air Emission Report for Preparedfor Emissions of Radionuclides Other Than Radon FromFugitive Air Emissions of Radionuclides from Diffuse Sources

Wahl, Linnea

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Radionuclide Air Emission Report for 2008  

E-Print Network (OSTI)

Fugitive Air Emissions of Radionuclides from Diffuse SourcesHazardous Air Pollutants (Radionuclides), Availability ofLBNL to Revise Its Radionuclide NESHAP Monitoring Approach,

Wahl, Linnea

2009-01-01T23:59:59.000Z

322

Central Air conditioners | Open Energy Information  

Open Energy Info (EERE)

Page Edit History Facebook icon Twitter icon Central Air conditioners Jump to: navigation, search TODO: Add description List of Central Air conditioners Incentives Retrieved...

323

Review of air flow measurement techniques  

E-Print Network (OSTI)

chamber, passive sampling, passive solar house, measurementhouse, we planed the distribution of fresh air, passivepassive perfluorocarbon tracer technique for determining air infiltration rates into houses

McWilliams, Jennifer

2002-01-01T23:59:59.000Z

324

Mountain Air | Open Energy Information  

Open Energy Info (EERE)

Air Air Jump to: navigation, search Name Mountain Air Facility Mountain Air Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Terna Energy Developer Terna Energy Energy Purchaser Idaho Power Location Hammett ID Coordinates 42.98719519°, -115.3985024° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":42.98719519,"lon":-115.3985024,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

325

Kansas Air Quality Regulations (Kansas)  

Energy.gov (U.S. Department of Energy (DOE))

All new air contaminant emission sources or alterations to emission sources that are required to be reported shall be in compliance with all applicable emission control regulations at the time that...

326

Manual on indoor air quality  

Science Conference Proceedings (OSTI)

This reference manual was prepared to assist electric utilities in helping homeowners, builders, and new home buyers to understand a broad range of issues related to indoor air quality. The manual is directed to technically knowledgeable persons employed by utility companies - the customer service or marketing representative, applications engineer, or technician - who may not have specific expertise in indoor air quality issues. In addition to providing monitoring and control techniques, the manual summarizes the link between pollutant concentrations, air exchange, and energy conservation and describes the characteristics and health effects of selected pollutants. Where technical information is too lengthy or complex for inclusion in this volume, reference sources are given. Information for this manual was gathered from technical studies, manufacturers' information, and other materials from professional societies, institutes, and associations. The aim has been to provide objective technical and descriptive information that can be used by utility personnel to make informed decisions about indoor air quality issues.

Diamond, R.C.; Grimsrud, D.T.

1983-12-01T23:59:59.000Z

327

Kansas Air Quality Act (Kansas)  

Energy.gov (U.S. Department of Energy (DOE))

No person shall construct, own, operate, install, alter or use any air contaminant emission stationary source which, in accordance with rules and regulations, the secretary finds may cause or...

328

Nadir Correction of AIRS Radiances  

Science Conference Proceedings (OSTI)

A statistical method to correct for the limb effect in off-nadir Atmospheric Infrared Sounder (AIRS) channel radiances is described, using the channel radiance itself and principal components (PCs) of the other channel radiances to account for ...

Chee-Kiat Teo; Tieh-Yong Koh

2010-03-01T23:59:59.000Z

329

Air permitting of IGCC plants  

SciTech Connect

The IGCC process is, currently, the preferred choice over conventional thermal power production in regard to cleanup of fuel and significantly reduced contaminant emissions. The air permitting requirements include the review of: feed preparation and PM emissions; feed gasification and contaminant emissions; elemental sulfur recovery and SO{sub 2} emissions; options for carbon-dioxide recovery; syngas characteristics for combustion; CT design and combustion mechanisms; air contaminant emissions of CT; controlled CT emissions of nitrogen-oxides and carbon-monoxide gases using the SCR and oxidation catalysts, respectively; and, emission of volatile organic compounds (VOCs), and hazardous air pollutants (HAPs). However, the IGCC processes are being rigorously reviewed for the system integration and reliability, and significant reduction of air contaminant emissions (including the greenhouse gases). This paper included a review of IGCC air contaminant emission rates, and various applicable regulatory requirements, such as NSR (New Source Review), NSPS (New Source Performance Standards), and MACT (Maximum Achievable Control Technology). The IGCC facility's NOX, CO, SO{sub 2}, PM, VOCs, and HAPs emission rates would be significantly low. Thus, effective, construction and installation, and operation air permits would be necessary for IGCC facilities.

Chitikela, S.R.

2007-07-01T23:59:59.000Z

330

Common Air Conditioner Problems | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Common Air Conditioner Problems Common Air Conditioner Problems Common Air Conditioner Problems May 30, 2012 - 6:41pm Addthis A refrigerant leak is one common air conditioning problem. | Photo courtesy of ©iStockphoto/BanksPhotos. A refrigerant leak is one common air conditioning problem. | Photo courtesy of ©iStockphoto/BanksPhotos. What does this mean for me? You can eliminate the most common air conditioner problems before hiring an air conditioning technician. You can do some air conditioner maintenance and repair tasks yourself. One of the most common air conditioning problems is improper operation. If your air conditioner is on, be sure to close your home's windows and outside doors. For room air conditioners, isolate the room or a group of connected rooms as much as possible from the rest of your home.

331

Common Air Conditioner Problems | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Common Air Conditioner Problems Common Air Conditioner Problems Common Air Conditioner Problems May 30, 2012 - 6:41pm Addthis A refrigerant leak is one common air conditioning problem. | Photo courtesy of ©iStockphoto/BanksPhotos. A refrigerant leak is one common air conditioning problem. | Photo courtesy of ©iStockphoto/BanksPhotos. What does this mean for me? You can eliminate the most common air conditioner problems before hiring an air conditioning technician. You can do some air conditioner maintenance and repair tasks yourself. One of the most common air conditioning problems is improper operation. If your air conditioner is on, be sure to close your home's windows and outside doors. For room air conditioners, isolate the room or a group of connected rooms as much as possible from the rest of your home.

332

Low Velocity Sphere Impact of a Borosilicate Glass  

SciTech Connect

This report summarizes US Army TARDEC sponsored work at Oak Ridge National Laboratory (ORNL) involving low velocity (< 30 m/s or < 65 mph) ball impact testing of Borofloat borosilicate glass, and is a follow-up to a similar study completed by the authors on Starphire soda-lime silicate glass last year. The response of the borosilicate glass to impact testing at different angles was also studied. The Borofloat glass was supplied by the US Army Research Laboratory and its tin-side was impacted or indented. The intent was to better understand low velocity impact response in the Borofloat. Seven sphere materials were used whose densities bracket that of rock: borosilicate glass, soda-lime silicate glass, silicon nitride, aluminum oxide, zirconium oxide, carbon steel, and a chrome steel. A gas gun or a ball-drop test setup was used to produce controlled velocity delivery of the spheres against the glass tile targets. Minimum impact velocities to initiate fracture in the Borofloat were measured and interpreted in context to the kinetic energy of impact and the elastic property mismatch between the seven sphere-Borofloat-target combinations. The primary observations from this low velocity (< 30 m/s or < 65 mph) testing were: (1) BS glass responded similarly to soda-lime silicate glass when spherically indented but quite differently under sphere impact conditions; (2) Frictional effects contributed to fracture initiation in BS glass when it spherically indented. This effect was also observed with soda-lime silicate glass; (3) The force necessary to initiate fracture in BS glass under spherical impact decreases with increasing elastic modulus of the sphere material. This trend is opposite to what was observed with soda-lime silicate glass. Friction cannot explain this trend and the authors do not have a legitimate explanation for it yet; (4) The force necessary to initiate contact-induced fracture is higher under dynamic conditions than under quasi-static conditions. That difference decreases with increasing elastic modulus mismatch between the sphere material and borosilicate This trend was opposite in soda-lime silicate glass; (5) Fracture in borosilicate glass occurs at lower velocities (i.e., easier) at 24{sup o} than at 0{sup o} (orthogonal) and 46{sup o} of impact for the same probability of failure. Though not analyzed yet, this suggests that a convolution of kinetic energy and friction is contributing to that trend; (6) There is a subtle indication there was intra-tile differences in spherical indentation RCIF. This likely is not a material property nor exclusive to borosilicate glass, rather, it is a statistical response of a combination of local, surface-located flaw and imposed tensile stress. Understanding of the surface flaw population and flaw positioning can likely enable prediction of spherical indentation RCIF; and (7) Contact-induced fracture did not initiate in the Borofloat BS for impact kinetic energies up to {approx} 20 mJ. For kinetic energies between {approx} 20-150 mJ, fracture sometimes initiated. Contact-induced fracture would always occur for impact energies > 150 mJ. The energy values, and their boundaries, were much lower for BS glass than they were for soda-lime silicate glass.

Morrissey, Timothy G [ORNL; Ferber, Mattison K [ORNL; Wereszczak, Andrew A [ORNL; Fox, Ethan E [ORNL

2012-05-01T23:59:59.000Z

333

VELOCITY SELECTOR METHOD FOR THE SEPARATION OF ISOTOPES  

DOE Patents (OSTI)

A velocity selector apparatus is described for separating and collecting an enriched fraction of the isotope of a particular element. The invention has the advantage over conventional mass spectrometers in that a magnetic field is not used, doing away with the attendant problems of magnetic field variation. The apparatus separates the isotopes by selectively accelerating the ionized constituents present in a beam of the polyisotopic substance that are of uniform kinetic energy, the acceleration being applied intermittently and at spaced points along the beam and in a direction normal to the direction of the propagation of the uniform energy beam whereby a transverse displacement of the isotopic constituents of different mass is obtained.

Britten, R.J.

1957-12-31T23:59:59.000Z

334

Velocity shear-induced effects on electrostatic ion perturbations  

Science Conference Proceedings (OSTI)

Linear evolution of electrostatic perturbations in an unmagnetized electron{endash}ion plasma shear flow is studied. New physical effects, arising due to the non-normality of linear dynamics are disclosed. A new class of {ital nonperiodic collective mode} with vortical motion of ions, characterized by intense energy exchange with the mean flow, is found. It is also shown that the velocity shear induces extraction of the mean flow energy by ion-sound waves and that during the shear-induced evolution the ion-sound waves turn eventually into ion plasma oscillations. {copyright} {ital 1997 American Institute of Physics.}

Rogava, A.D. [Department of Physics, Tbilisi State University, and Department of Theoretical Astrophysics, Abastumani Astrophysical Observatory, Tbilisi, Republic of (Georgia)] [Department of Physics, Tbilisi State University, and Department of Theoretical Astrophysics, Abastumani Astrophysical Observatory, Tbilisi, Republic of (Georgia); Chagelishvili, G.D. [Department of Theoretical Astrophysics, Abastumani Astrophysical Observatory, Tbilisi, Republic of (Georgia)] [Department of Theoretical Astrophysics, Abastumani Astrophysical Observatory, Tbilisi, Republic of (Georgia); [Department of Cosmogeophysics, Space Research Institute, Moscow (Russia); Berezhiani, V.I. [Department of Plasma Physics, Institute of Physics, Tbilisi, Republic of (Georgia)] [Department of Plasma Physics, Institute of Physics, Tbilisi, Republic of (Georgia)

1997-12-01T23:59:59.000Z

335

Determination of sputtered atom densities and velocities via simulation  

Science Conference Proceedings (OSTI)

Transport of sputtered atoms in a plasma sputtering unit is simulated using two known elastic collision models. The methods of studying the collision of two atoms are isotropic random scattering angle in the center of mass frame and the so-called center to center collision model in which the impact parameter is ignored and the two particles collide such as two material points. The obtained results for the density and velocity of sputtered atoms in both models are compared with some experimental reports. This investigation shows that the copper and argon atoms present pointlike behavior in the collision process.

Khorram, S.; Sobhanian, S. [Faculty of Physics, University of Tabriz, Tabriz, 51666 (Iran, Islamic Republic of); Research Institute for Applied Physics and Astronomy, University of Tabriz, Tabriz, 51666 (Iran, Islamic Republic of); Naghshara, H. [Faculty of Physics, University of Tabriz, Tabriz, 51666 (Iran, Islamic Republic of)

2011-04-01T23:59:59.000Z

336

Method and apparatus for measuring flow velocity using matched filters  

DOE Patents (OSTI)

An apparatus and method for measuring the flow velocities of individual phase flow components of a multiphase flow is disclosed. Signals arising from flow noise disturbance are extracted from the flow, at upstream and downstream locations. The signals are processed through pairs of matched filters which are matched to the flow disturbance frequency characteristics of the phase flow component to be measured. The processed signals are then cross-correlated to determine the transit delay time of the phase flow component between sensing positions.

Raptis, A.C.

1981-07-17T23:59:59.000Z

337

Velocity Profiles in a Cylindrical Liquid Jet by Reconstructed Velocimetry  

E-Print Network (OSTI)

in such a way that the jet boundaries appeared sharply focused. The Newtonian liquid used in all the experiments was a mixture of 74.7% glycerol (99.9% pure) with 25.3% tri- distilled water (weight percentage). Its measured properties were: density ? = 1250... dynamics theory (or numerical simulations) for un-wetted nozzles, but to explore the effects of nozzle wetting on the velocity profiles. It is well-known that nozzle face wetting slightly enlarges the jet diameter for some distance down- stream from...

Castrejon-Pita, J.R.; Hoath, S.D.; Hutchings, I.M.

2012-01-01T23:59:59.000Z

338

A VAD-Based Dealiasing Method for Radar Velocity Data Quality Control  

Science Conference Proceedings (OSTI)

This paper describes a new velocityazimuth display (VAD)-based dealiasing method developed for automated radar radial velocity data quality control to satisfy the high-quality standard and efficiency required by operational radar data ...

Qin Xu; Kang Nai; Li Wei; Pengfei Zhang; Shun Liu; David Parrish

2011-01-01T23:59:59.000Z

339

An Optical Array Instrument for Shape and Fall Velocity Measurements of Hydrometeors  

Science Conference Proceedings (OSTI)

A ground-based optical array instrument for the measurement of shapes, sizes, and fall velocities of freely falling hydrometeors is presented. The instrument, the Hydrometeor Velocity and Shape Detector (HVSD), is designed to accurately measure ...

E. Barthazy; S. Gke; R. Schefold; D. Hgl

2004-09-01T23:59:59.000Z

340

Combining Inverted Echo Sounder and Horizontal Electric Field Recorder Measurements to Obtain Absolute Velocity Profiles  

Science Conference Proceedings (OSTI)

Profiles of absolute velocity are difficult to obtain in the ocean, especially over long periods of time at the same location. This paper presents a method of estimating full water column absolute horizontal velocity profiles as a function of ...

Christopher S. Meinen; Douglas S. Luther; D. Randolph Watts; Karen L. Tracey; Alan D. Chave; James Richman

2002-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

A Comparison of Vertical Velocity in Cirrus Obtained from Aircraft and Lidar Divergence Measurements during FIRE  

Science Conference Proceedings (OSTI)

Techniques are presented to obtain vertical velocity in cirrus clouds from in situ aircraft lateral wind measurements and from ground-based remote Doppler lidar measurements. In general, direct measurements of absolute vertical velocity w from ...

I. Gultepe; A. J. Heymsfield; D. H. Lenschow

1990-02-01T23:59:59.000Z

342

Dependence of Turbulent and Mesoscale Velocity Variances on Scale and Stability  

Science Conference Proceedings (OSTI)

The scale dependence of velocity variances is studied using data collected from a grassland site, a heather site, and four forested sites. The dependence of velocity variances on averaging time, used to define the fluctuation quantities, is ...

L. Mahrt; Erin Moore; Dean Vickers; N. O. Jensen

2001-03-01T23:59:59.000Z

343

Peak ground velocity evaluation by artificial neural network for west america region  

Science Conference Proceedings (OSTI)

With the Peak Ground Velocity 283 records in three dimensions, the velocity attenuation relationship with distance was discussed by neural network in this paper. The earthquake magnitude, epicenter distance, site intensity and site condition were considered ...

Ben-yu Liu; Liao-yuan Ye; Mei-ling Xiao; Sheng Miao

2006-10-01T23:59:59.000Z

344

Non-Gaussian Velocity Probability Density Functions: An Altimetric Perspective of the Mediterranean Sea  

Science Conference Proceedings (OSTI)

Velocity probability density functions (PDFs) are a key tool to study complex flows and are of great importance to model particle dispersion. The PDFs of geostrophic velocities derived from sea level anomalies maps for the Mediterranean Sea have ...

Jordi Isern-Fontanet; Emilio Garca-Ladona; Jordi Font; Antonio Garca-Olivares

2006-11-01T23:59:59.000Z

345

Effects of Radar Proximity on Single-Doppler Velocity Signatures of Axisymmetric Rotation and Divergence  

Science Conference Proceedings (OSTI)

Geometrical and mathematical relationships are developed to explain the variation with radar range of idealized single-Doppler velocity patterns of axisymmetric rotation and divergence regions. The velocity patterns become distorted as they ...

Vincent T. Wood; Rodger A. Brown

1992-12-01T23:59:59.000Z

346

An Intercomparison Study Using Electromagnetic Three-Component Turbulent Velocity Probes  

Science Conference Proceedings (OSTI)

An intercomparison study was performed with four Russian-made, electromagnetic probes capable of measuring three components of oceanic turbulent velocities and two single-axis velocity sensors familiar to western scientists, namely, a hot-film ...

David Y. Lai; Vadim T. Paka; Donald P. Delisi; Anatoli V. Arjannikov; Sergei A. Khanaev

2000-07-01T23:59:59.000Z

347

A QUANTUM MECHANICAL APPROACH TO THE VELOCITY OF DISLOCATIONS IN ICE  

E-Print Network (OSTI)

~, A. ~ Higashi, A. , Physics of Ice, edited by N. Riehl, B.THE VELOCITY OF DISLOCATIONS IN ICE RECEIVED LAWRENCE A. R.the velocity of dislocations in ice ref. (3,4) with which we

Forouhi, A.R.

2011-01-01T23:59:59.000Z

348

Computation of the Streamfunction and Velocity Potential for Limited and Irregular Domains  

Science Conference Proceedings (OSTI)

An algorithm is proposed for the computation of streamfunction and velocity potential from given horizontal velocity vectors based on solving a minimization problem. To guarantee the uniqueness of the solution and computational reliability of the ...

Zhijin Li; Yi Chao; James C. McWilliams

2006-11-01T23:59:59.000Z

349

Velocity Mapping Capabilities of Present and Future Altimeter Missions: The Role of High-Frequency Signals  

Science Conference Proceedings (OSTI)

A detailed analysis of the velocity field mapping capabilities from existing and future multiple altimeter missions is carried out using the Los Alamos North Atlantic high-resolution model. The velocity mapping errors on the instantaneous fields ...

P. Y. Le Traon; G. Dibarboure

2002-12-01T23:59:59.000Z

350

On the Structure of the Velocity Field over Progressive Mechanically-Generated Water Waves  

Science Conference Proceedings (OSTI)

The structure of the velocity field over a propagating wave of fixed frequency is examined. The vertical and horizontal velocities were measured in a transformed Eulerian wave-following frame of reference in a wind-wave research facility at ...

Yiannis Alex Papadimitrakis; En Yun Hsu; Robert L. Street

1984-12-01T23:59:59.000Z

351

Robust Estimations of Current Velocities with Four-Beam Broadband ADCPs  

Science Conference Proceedings (OSTI)

An extended explanation of the hypothesis and equations traditionally used to transform between four-beam ADCP radial beam velocities and current velocity components is presented. This explanation includes a dissertation about the meaning of the ...

M. Gilcoto; Emlyn Jones; Luis Faria-Busto

2009-12-01T23:59:59.000Z

352

Terminal Velocities of Droplets and Crystals: Power Laws with Continuous Parameters over the Size Spectrum  

Science Conference Proceedings (OSTI)

This paper presents a unified treatment of cloud particle fall velocities for both liquid and crystalline cloud particles over the entire size range observed in the atmosphere. The fall velocity representation is formulated in terms of the Best (...

Vitaly I. Khvorostyanov; Judith A. Curry

2002-06-01T23:59:59.000Z

353

Distributions of Raindrop Sizes and Fall Velocities in a Semiarid Plateau Climate: Convective versus Stratiform Rains  

Science Conference Proceedings (OSTI)

Joint size and fall velocity distributions of raindrops were measured with a Particle Size and Velocity (PARSIVEL) precipitation particle disdrometer in a field experiment conducted during July and August 2007 at a semiarid continental site ...

Shengjie Niu; Xingcan Jia; Jianren Sang; Xiaoli Liu; Chunsong Lu; Yangang Liu

2010-04-01T23:59:59.000Z

354

Supply Fan Control for Constant Air Volume Air Handling Units  

E-Print Network (OSTI)

Since terminal boxes do not have a modulation damper in constant volume (CV) air handling unit (AHU) systems, zone reheat coils have to be modulated to maintain the space temperature with constant supply airflow. This conventional control sequence causes a significant amount of reheat and constant fan power under partial load conditions. Variable Frequency Drives (VFDs) can be installed on these constant air volume systems. The fan speed can be modulated based on the maximum zone load. This paper present the procedure to control the supply fan speed and analyzes the thermal performance and major fan energy and thermal energy savings without expensive VAV retrofit through the actual system operation.

Cho, Y.; Wang, G.; Liu, M.

2007-01-01T23:59:59.000Z

355

Air Breathing Direct Methanol Fuel Cell  

NLE Websites -- All DOE Office Websites (Extended Search)

Air Breathing Direct Methanol Fuel Cell Air Breathing Direct Methanol Fuel Cell Air Breathing Direct Methanol Fuel Cell An air breathing direct methanol fuel cell is provided with a membrane electrode assembly, a conductive anode assembly that is permeable to air and directly open to atmospheric air, and a conductive cathode assembly that is permeable to methanol and directly contacting a liquid methanol source. Available for thumbnail of Feynman Center (505) 665-9090 Email Air Breathing Direct Methanol Fuel Cell An air breathing direct methanol fuel cell is provided with a membrane electrode assembly, a conductive anode assembly that is permeable to air and directly open to atmospheric air, and a conductive cathode assembly that is permeable to methanol and directly contacting a liquid methanol

356

Tips: Air Ducts | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Air Ducts Air Ducts Tips: Air Ducts June 24, 2013 - 7:23pm Addthis Air Ducts: Out of Sight, Out of Mind. The unsealed ducts in your attic and crawlspaces lose air, and uninsulated ducts lose heat -- wasting energy and money. Air Ducts: Out of Sight, Out of Mind. The unsealed ducts in your attic and crawlspaces lose air, and uninsulated ducts lose heat -- wasting energy and money. Your air ducts are one of the most important systems in your home, and if the ducts are poorly sealed or insulated they are likely contributing to higher energy bills. Your home's duct system is a branching network of tubes in the walls, floors, and ceilings; it carries the air from your home's furnace and central air conditioner to each room. Ducts are made of sheet metal, fiberglass, or other materials.

357

Improved intake air filtration systems  

SciTech Connect

This report comprises the results of a project sponsored by the Pipeline Research Committee of the American Gas Association (Improved Intake Air Filtration Systems). The quality of the inlet air consumed by pipeline gas turbines plays a significant role in the performance, maintenance, and economy of turbine operations. The airborne contaminants may cause degradation of compressor blades and hot gas path components, primarily by erosion, corrosion, and fouling. Machines in the pipeline fleet have a typical average loss of 3.5% in output, chiefly caused by fouling of the gas turbine compressor. It also showed that: Air contamination could be significantly reduced by the use of more efficient air filtration systems, especially through the reduction of the quantity of smaller particles ingested.'' Filters which incorporated electrostatically charged fibers (achieved through the use of triboelectric [TE] effects) offered the most promising means for developing an improvement over paper media. The purpose of this program was to validate the use of new technology for self-cleaning air inlet filtration on gas turbine pumping applications. An approach utilizing triboelectrification of fabric filters was examined by testing to determine the penetration (efficiency), cleanability, pressure drop vs flow, and dust-holding capacity of seven pairs of filter cartridges: six fabric and one paper.

Lawson, C.C. (Lawson (Calvin C.), North Wildwood, NJ (United States))

1991-09-01T23:59:59.000Z

358

CFD Simulation and Analysis of the Combined Evaporative Cooling and Radiant Ceiling Air-conditioning System  

E-Print Network (OSTI)

Due to such disadvantages as large air duct and high energy consumption of the current all- outdoor air evaporative cooling systems used in the dry region of Northwest China, as well as the superiority of the ceiling cooling system in improving thermal comfort and saving energy, a combined system is presented in this paper. It combines an evaporative cooling system with ceiling cooling, in which the evaporative cooling system handles the entire latent load and one part of the sensible loads, and the ceiling cooling system deals with the other part of sensible loads in the air-conditioned zone, so that the condensation on radiant panels and the insufficiency of cooling capacity can be avoided. The cooling water at 18? used in the cooling coils of ceiling cooling system can be ground water, tap water or the cooled water from cooling towers in the summer. This new air-conditioning system and existing all- outdoor air evaporative cooling system are applied to a project in the city of Lanzhou. Energy consumption analysis of the building is carried out using the energy consumption code. Velocity and temperature distribution in the air-conditioned zone is computed using CFD. According to the results, the energy consumption and indoor human thermal comfort of both systems are then compared. It is concluded that the new system occupies less building space, reduces energy consumption, improves indoor human thermal comfort and saves initial investment.

Xiang, H.; Yinming, L.; Junmei, W.

2006-01-01T23:59:59.000Z

359

Considering Air Density in Wind Power Production  

E-Print Network (OSTI)

In the wind power production calculations the air density is usually considered as constant in time. Using the CIPM-2007 equation for the density of moist air as a function of air temperature, air pressure and relative humidity, we show that it is worth taking the variation of the air density into account, because higher accuracy can be obtained in the calculation of the power production for little effort.

Zn Farkas

2011-03-11T23:59:59.000Z

360

Thermalization in harmonic particle chains with velocity flips  

E-Print Network (OSTI)

We propose a new mathematical tool for the study of transport properties of models for lattice vibrations in crystalline solids. By replication of dynamical degrees of freedom, we aim at a new dynamical system where the "local" dynamics can be isolated and solved independently from the "global" evolution. The replication procedure is very generic but not unique as it depends on how the original dynamics are split between the local and global dynamics. As an explicit example, we apply the scheme to study thermalization of the pinned harmonic chain with velocity flips. We improve on the previous results about this system by showing that after a relatively short time period the average kinetic temperature profile satisfies the dynamic Fourier's law in a local microscopic sense without assuming that the initial data is close to a local equilibrium state. The bounds derived here prove that the above thermalization period is at most of the order L^(2/3), where L denotes the number of particles in the chain. In particular, even before the diffusive time scale Fourier's law becomes a valid approximation of the evolution of the kinetic temperature profile. As a second application of the dynamic replica method, we also briefly discuss replacing the velocity flips by an anharmonic onsite potential.

Jani Lukkarinen

2013-08-22T23:59:59.000Z

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Low Velocity Sphere Impact of a Borosilicate Glass  

Science Conference Proceedings (OSTI)

This report summarizes US Army TARDEC sponsored work at Oak Ridge National Laboratory (ORNL) involving low velocity (energy of impact and the elastic property mismatch between the seven sphere-Borofloat-target combinations. The primary observations from this low velocity (energy and friction is contributing to that trend; (6) There is a subtle indication there was intra-tile differences in spherical indentation RCIF. This likely is not a material property nor exclusive to borosilicate glass, rather, it is a statistical response of a combination of local, surface-located flaw and imposed tensile stress. Understanding of the surface flaw population and flaw positioning can likely enable prediction of spherical indentation RCIF; and (7) Contact-induced fracture did not initiate in the Borofloat BS for impact kinetic energies up to {approx} 20 mJ. For kinetic energies between {approx} 20-150 mJ, fracture sometimes initiated. Contact-induced fracture would always occur for impact energies > 150 mJ. The energy values, and their boundaries, were much lower for BS glass than they were for soda-lime silicate glass.

Morrissey, Timothy G [ORNL; Ferber, Mattison K [ORNL; Wereszczak, Andrew A [ORNL; Fox, Ethan E [ORNL

2012-05-01T23:59:59.000Z

362

A new rf structure for intermediate-velocity particles  

Science Conference Proceedings (OSTI)

This paper describes an rf structure with high shunt impedance and good field stability for particle velocities o.1 {le} {beta} {le} 0.5. Traditionally, the drift-tube linac (DTL) has been the structure of choice for this velocity range. The new structure, called a coupled-cavity drift-tube linac (CCDTL), combines features of the Alvarez DTL and the {pi}-mode coupled-cavity linac (CCL). Each accelerating cavity is a two-cell, 0-mode DTL. The center-to-center distance between gaps is {gamma}{lambda}. Adjacent accelerating cavities have oppositely directed electric fields, alternating in phase by 180{degrees}. The chain of cavities operates in a {pi}/2 structure mode so the coupling cavities are nominally unexcited. We will discuss 2-D and 3-D electromagnetic code calculations, and some initial measurements on a low-power model of a CCDTL. We will compare shunt impedance calculations for DTL, CCL, and CCDTL structures. The CCDTL has potential application for a wide range of ion linacs. For example, high-intensity proton linacs could use the CCDTL instead of a DTL up to an energy of about 200 MeV. Another example is a stand-alone, low-duty, low-current, very high gradient, proton, cancer therapy machine. The advantage for this application would be a saving in the cost of the machine because the linac would be short.

Billen, J.H.; Krawczyk, F.L.; Wood, R.L.; Young, L.M.

1994-09-01T23:59:59.000Z

363

Investigation of Feasibility of All-Fresh Air Supply in an All-Air System  

E-Print Network (OSTI)

The feasibility of an all-fresh air supply in an all-air system is investigated in theory, and the problem of AHU-handling air in low efficiency in summer and winter conditions is analyzed. The air supply temperature is almost up to standards when a heat recovery unit is fixed in the air conditioning system.

Wang, J.; Yan, Z.

2006-01-01T23:59:59.000Z

364

inAir: Measuring and Visualizing Indoor Air Quality Sunyoung Kim & Eric Paulos  

E-Print Network (OSTI)

, air quality, domestic computing, health ACM Classification Keywords H.m. Information interfacesinAir: Measuring and Visualizing Indoor Air Quality Sunyoung Kim & Eric Paulos Human}@cs.cmu.edu ABSTRACT Good indoor air quality is a vital part of human health. Poor indoor air quality can contribute

Paulos, Eric

365

One-step reduced kinetics for lean hydrogen-air deflagration  

Science Conference Proceedings (OSTI)

A short mechanism consisting of seven elementary reactions, of which only three are reversible, is shown to provide good predictions of hydrogen-air lean-flame burning velocities. This mechanism is further simplified by noting that over a range of conditions of practical interest, near the lean flammability limit all reaction intermediaries have small concentrations in the important thin reaction zone that controls the hydrogen-air laminar burning velocity and therefore follow a steady state approximation, while the main species react according to the global irreversible reaction 2H{sub 2} + O{sub 2} {yields} 2H{sub 2}O. An explicit expression for the non-Arrhenius rate of this one-step overall reaction for hydrogen oxidation is derived from the seven-step detailed mechanism, for application near the flammability limit. The one-step results are used to calculate flammability limits and burning velocities of planar deflagrations. Furthermore, implications concerning radical profiles in the deflagration and reasons for the success of the approximations are clarified. It is also demonstrated that adding only two irreversible direct recombination steps to the seven-step mechanism accurately reproduces burning velocities of the full detailed mechanism for all equivalence ratios at normal atmospheric conditions and that an eight-step detailed mechanism, constructed from the seven-step mechanism by adding to it the fourth reversible shuffle reaction, improves predictions of O and OH profiles. The new reduced-chemistry descriptions can be useful for both analytical and computational studies of lean hydrogen-air flames, decreasing required computation times. (author)

Fernandez-Galisteo, D.; Sanchez, A.L. [Area de Mecanica de Fluidos, Univ. Carlos III de Madrid, Leganes 28911 (Spain); Linan, A. [ETSI Aeronauticos, Pl. Cardenal Cisneros 3, Madrid 28040 (Spain); Williams, F.A. [Dept. of Mechanical and Aerospace Engineering, University of California San Diego, La Jolla, CA 92093-0411 (United States)

2009-05-15T23:59:59.000Z

366

Initial Examination of Low Velocity Sphere Impact of Glass Ceramics  

SciTech Connect

This report summarizes US Army TARDEC sponsored work at Oak Ridge National Laboratory (ORNL) involving low velocity (< 30 m/s or < 65 mph) sphere impact testing of two materials from the lithium aluminosilicate family reinforced with different amounts of ceramic particulate, i.e., glass-ceramic materials, SCHOTT Resistan{trademark}-G1 and SCHOTT Resistan{trademark}-L. Both materials are provided by SCHOTT Glass (Duryea, PA). This work is a follow-up to similar sphere impact studies completed by the authors on PPG's Starphire{reg_sign} soda-lime silicate glass and SCHOTT BOROFLOAT{reg_sign} borosilicate glass. A gas gun or a sphere-drop test setup was used to produce controlled velocity delivery of silicon nitride (Si{sub 3}N{sub 4}) spheres against the glass ceramic tile targets. Minimum impact velocities to initiate fracture in the glass-ceramics were measured and interpreted in context to the kinetic energy of impact and the elastic property mismatch between sphere and target material. Quasistatic spherical indentation was also performed on both glass ceramics and their contact damage responses were compared to those of soda-lime silicate and borosilicate glasses. Lastly, variability of contact damage response was assessed by performing spherical indentation testing across the area of an entire glass ceramic tile. The primary observations from this low velocity (< 30 m/s or < 65 mph) testing were: (1) Resistan{trademark}-L glass ceramic required the highest velocity of sphere impact for damage to initiate. Starphire{reg_sign} soda-lime silicate glass was second best, then Resistan{trademark}-G1 glass ceramic, and then BOROFLOAT{reg_sign} borosilicate glass. (2) Glass-ceramic Resistan{trademark}-L also required the largest force to initiate ring crack from quasi-static indentation. That ranking was followed, in descending order, by Starphire{reg_sign} soda-lime silicate glass, Resistan{trademark}-G1 glass ceramic, and BOROFLOAT{reg_sign} borosilicate glass. (3) Spheres with a lower elastic modulus require less force to initiate fracture in Resistan{trademark}-G1 from quasi-static spherical indentation. This indicates that friction is affecting ring crack initiation in Resistan{trademark}-G1. Friction also affected ring crack initiation in Starphire{reg_sign} soda-lime silicate and BOROFLOAT{reg_sign} borosilicate glasses. Among these three materials, friction was the most pronounced (largest slope in the RCIF-elastic modulus graph) in the Starphire{reg_sign} and least pronounced in the BOROFLOAT{reg_sign}. The reason for this is not understood, but differences in deformation behavior under high contact stresses could be a cause or contributor to this. (4) The force necessary to initiate contact-induced fracture is higher under dynamic conditions than it is under quasi-static conditions in Resistan{trademark}-L and Resistan{trademark}-G1 glass ceramics. This is a trend observed too in Starphire{reg_sign} and BOROFLOAT{reg_sign}. (5) There is a subtle indication there was intra-tile differences in spherical indentation-induced ring crack initiation forces. This is not a material property nor is it exclusive to glass-ceramic Resistan{trademark}-G1 glass ceramic, rather, it is a statistical mechanical response to an accumulated history of processing and handling of that specific tile.

Morrissey, Timothy G [ORNL; Fox, Ethan E [ORNL; Wereszczak, Andrew A [ORNL; Ferber, Mattison K [ORNL

2012-06-01T23:59:59.000Z

367

Air Showers and Geomagnetic Field  

E-Print Network (OSTI)

The influence of the geomagnetic field on the development of air showers is studied. The well known International Geomagnetic Reference Field was included in the AIRES air shower simulation program as an auxiliary tool to allow calculating very accurate estimations of the geomagnetic field given the geographic coordinates, altitude above sea level and date of a given event. Our simulations indicate that the geomagnetic deflections alter significantly some shower observables like, for example, the lateral distribution of muons in the case of events with large zenith angles (larger than 75 degrees). On the other hand, such alterations seem not to be important for smaller zenith angles. Global observables like total numbers of particles or longitudinal development parameters do not present appreciable dependences on the geomagnetic deflections for all the cases that were studied.

A. Cillis; S. J. Sciutto

1999-07-31T23:59:59.000Z

368

Initial Examination of Low Velocity Sphere Impact of Glass Ceramics  

Science Conference Proceedings (OSTI)

This report summarizes US Army TARDEC sponsored work at Oak Ridge National Laboratory (ORNL) involving low velocity (energy of impact and the elastic property mismatch between sphere and target material. Quasistatic spherical indentation was also performed on both glass ceramics and their contact damage responses were compared to those of soda-lime silicate and borosilicate glasses. Lastly, variability of contact damage response was assessed by performing spherical indentation testing across the area of an entire glass ceramic tile. The primary observations from this low velocity (< 30 m/s or < 65 mph) testing were: (1) Resistan{trademark}-L glass ceramic required the highest velocity of sphere impact for damage to initiate. Starphire{reg_sign} soda-lime silicate glass was second best, then Resistan{trademark}-G1 glass ceramic, and then BOROFLOAT{reg_sign} borosilicate glass. (2) Glass-ceramic Resistan{trademark}-L also required the largest force to initiate ring crack from quasi-static indentation. That ranking was followed, in descending order, by Starphire{reg_sign} soda-lime silicate glass, Resistan{trademark}-G1 glass ceramic, and BOROFLOAT{reg_sign} borosilicate glass. (3) Spheres with a lower elastic modulus require less force to initiate fracture in Resistan{trademark}-G1 from quasi-static spherical indentation. This indicates that friction is affecting ring crack initiation in Resistan{trademark}-G1. Friction also affected ring crack initiation in Starphire{reg_sign} soda-lime silicate and BOROFLOAT{reg_sign} borosilicate glasses. Among these three materials, friction was the most pronounced (largest slope in the RCIF-elastic modulus graph) in the Starphire{reg_sign} and least pronounced in the BOROFLOAT{reg_sign}. The reason for this is not understood, but differences in deformation behavior under high contact stresses could be a cause or contributor to this. (4) The force necessary to initiate contact-induced fracture is higher under dynamic conditions than it is under quasi-static conditions in Resistan{trademark}-L and Resistan{trademark}-G1 glass ceramics. This is a trend observed too in Starphire{reg_sign} and BOROFLOAT{reg_sign}. (5) There is a subtle indication there was intra-tile differences in spherical indentation-induced ring crack initiation forces. This is not a material property nor is it exclusive to glass-ceramic Resistan{trademark}-G1 glass ceramic, rather, it is a statistical mechanical response to an accumulated history of processing and handling of that specific tile.

Morrissey, Timothy G [ORNL; Fox, Ethan E [ORNL; Wereszczak, Andrew A [ORNL; Ferber, Mattison K [ORNL

2012-06-01T23:59:59.000Z

369

Maintaining Your Air Conditioner | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Maintaining Your Air Conditioner Maintaining Your Air Conditioner Maintaining Your Air Conditioner June 18, 2013 - 6:20pm Addthis Replacing or cleaning air conditioner filters is a critical maintenance task. | Photo courtesy of ©iStockphoto/firemanYU. Replacing or cleaning air conditioner filters is a critical maintenance task. | Photo courtesy of ©iStockphoto/firemanYU. What does this mean for me? Regular maintenance keeps your air conditioner running as efficiently as possible. Maintaining your air conditioner will save you money by extending the unit's life. An air conditioner's filters, coils, and fins require regular maintenance for the unit to function effectively and efficiently throughout its years of service. Neglecting necessary maintenance ensures a steady decline in air conditioning performance while energy use steadily increases.

370

Air Sealing Your Home | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Air Sealing Your Home Air Sealing Your Home Air Sealing Your Home November 26, 2013 - 6:22pm Addthis Save on heating and cooling costs by checking for air leaks in common trouble spots in your home. Save on heating and cooling costs by checking for air leaks in common trouble spots in your home. What does this mean for me? Save money and energy by air sealing your house. Caulking and weatherstripping are simple, effective ways of sealing air leaks in your home. Reducing the amount of air that leaks in and out of your home is a cost-effective way to cut heating and cooling costs, improve durability, increase comfort, and create a healthier indoor environment. Caulking and weatherstripping are two simple and effective air-sealing techniques that offer quick returns on investment, often one year or less. Caulk is

371

Maintaining Your Air Conditioner | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Maintaining Your Air Conditioner Maintaining Your Air Conditioner Maintaining Your Air Conditioner June 18, 2013 - 6:20pm Addthis Replacing or cleaning air conditioner filters is a critical maintenance task. | Photo courtesy of ©iStockphoto/firemanYU. Replacing or cleaning air conditioner filters is a critical maintenance task. | Photo courtesy of ©iStockphoto/firemanYU. What does this mean for me? Regular maintenance keeps your air conditioner running as efficiently as possible. Maintaining your air conditioner will save you money by extending the unit's life. An air conditioner's filters, coils, and fins require regular maintenance for the unit to function effectively and efficiently throughout its years of service. Neglecting necessary maintenance ensures a steady decline in air conditioning performance while energy use steadily increases.

372

Optimal Outside Air Control for Air Handling Units with Humidity Control  

E-Print Network (OSTI)

Most air handling units (AHUs) in commercial buildings have the (air) economizer cycle to use outside air for free cooling under certain outside air conditions. Ideally the economizer cycle is enabled if outside air enthalpy is less than return air enthalpy. During the economizer cycle, outside air flow is modulated to seek mixed air temperature at a supply air temperature set point. Since the outside air may be dry during the economizer cycle, humidification is required for AHUs with humidity control. As a result, the economizer cycle saves cooling energy but requires excessive steam for humidification. Therefore the economizer cycle may not be economical. An optimal outside air control method is developed to minimize the total cost of mechanical cooling and steam humidification. The impacts of chilled water price, steam price, and space minimum humidity set point are analyzed. Finally the optimal outside air control zones are presented on a psychrometric chart under differential energy price ratios and minimum indoor humidity set points.

Wang, G.; Liu, M.

2006-01-01T23:59:59.000Z

373

I) EXAS AIR CONTROL BLAR  

NLE Websites -- All DOE Office Websites (Extended Search)

I) EXAS AIR CONTROL BLAR 6330 HWY. 290 EAST, AUSTIN, TEXAS 78723, 512451-5711 DICK WHmINGTON, P.E. JOHN L. BLAIR CHAIRMAN MARCUS M. KEY, M.D. CALVIN 8. PARNELL, JR., Ph.D., P.E....

374

Air-leakage control manual  

Science Conference Proceedings (OSTI)

This manual is for builders and designers who are interested in building energy-efficient homes. The purpose of the manual is to provide the ``how and why`` of controlling air leakage by means of a system called the ``Simple Caulk and Seal`` (SIMPLE{center_dot}CS) system. This manual provides an overview of the purpose and contents of the manual; It discusses the forces that affect air leakage in homes and the benefits of controlling air leakage. Also discussed are two earlier approaches for controlling air leakage and the problems with these approaches. It describes the SIMPLE-{center_dot}CS system. It outlines the standard components of the building envelope that require sealing and provides guidelines for sealing them. It outlines a step-by-step procedure for analyzing and planning the sealing effort. The procedure includes (1) identifying areas to be sealed, (2) determining the most effective and convenient stage of construction in which to do the sealing, and (3) designating the appropriate crew member or trade to be responsible for the sealing.

Maloney, J. [Washington State Energy Office, Olympia, WA (United States)

1991-05-01T23:59:59.000Z

375

Air-Leakage Control Manual.  

Science Conference Proceedings (OSTI)

This manual is for builders and designers who are interested in building energy-efficient homes. The purpose of the manual is to provide the how and why'' of controlling air leakage by means of a system called the Simple Caulk and Seal'' (SIMPLE{center dot}CS) system. This manual provides an overview of the purpose and contents of the manual; It discusses the forces that affect air leakage in homes and the benefits of controlling air leakage. Also discussed are two earlier approaches for controlling air leakage and the problems with these approaches. It describes the SIMPLE-{center dot}CS system. It outlines the standard components of the building envelope that require sealing and provides guidelines for sealing them. It outlines a step-by-step procedure for analyzing and planning the sealing effort. The procedure includes (1) identifying areas to be sealed, (2) determining the most effective and convenient stage of construction in which to do the sealing, and (3) designating the appropriate crew member or trade to be responsible for the sealing.

Maloney, Jim; Washington State Energy Office; United States. Bonneville Power Administration.

1991-05-01T23:59:59.000Z

376

220-MW compressed air storage  

Science Conference Proceedings (OSTI)

SOYLAND Power Cooperative, Inc., a Decatur, Illinois based co-op, could get reasonably priced baseload power from neighboring utilities, had a plant of its own planned for the near future as well as a share in another, but peaking power, generated by oil and gas, to meet surges in demand, was very costly. The co-op's solution, first in the U.S., is a 220-megawatt compressed air energy storage system (CAES), which the electric utility industry is watching with great interest. CAES splits the two basic stages of a conventional gas turbine, making the most of baseload power while using the least peaking or intermediate fuel. During off-peak periods, inexpensive baseload electricity from coal or nuclear power plants runs a combination motor-generator in motor mode which, in turn, operates a compressor. The compressed air is cooled and pumped into an underground storage reservoir hundreds of thousands of cubic yards in volume and about two thousand feet (about 610 m) below the surface. There the air remains, at pressures up to about 60 atm (6.1 MPa), until peaking or intermediate power is required. Then, the air is released into a combustor at a controlled rate, heated by oil or gas, and expanded through a turbine. The turbine drives the motor-generator in a generator mode, thereby supplying peaking or intermediate power to the grid.

Lihach, N.

1983-01-01T23:59:59.000Z

377

ISOTHERMAL AIR INGRESS VALIDATION EXPERIMENTS  

SciTech Connect

Idaho National Laboratory carried out air ingress experiments as part of validating computational fluid dynamics (CFD) calculations. An isothermal test loop was designed and set to understand the stratified-flow phenomenon, which is important as the initial air flow into the lower plenum of the very high temperature gas cooled reactor (VHTR) when a large break loss-of-coolant accident occurs. The unique flow characteristics were focused on the VHTR air-ingress accident, in particular, the flow visualization of the stratified flow in the inlet pipe to the vessel lower plenum of the General Atomics Gas Turbine-Modular Helium Reactor (GT-MHR). Brine and sucrose were used as heavy fluids, and water was used to represent a light fluid, which mimics a counter current flow due to the density difference between the stimulant fluids. The density ratios were changed between 0.87 and 0.98. This experiment clearly showed that a stratified flow between simulant fluids was established even for very small density differences. The CFD calculations were compared with experimental data. A grid sensitivity study on CFD models was also performed using the Richardson extrapolation and the grid convergence index method for the numerical accuracy of CFD calculations . As a result, the calculated current speed showed very good agreement with the experimental data, indicating that the current CFD methods are suitable for predicting density gradient stratified flow phenomena in the air-ingress accident.

Chang H Oh; Eung S Kim

2011-09-01T23:59:59.000Z

378

On anomalous diffusion in a plasma in velocity space  

E-Print Network (OSTI)

The problem of anomalous diffusion in momentum space is considered for plasma-like systems on the basis of a new collision integral, which is appropriate for consideration of the probability transition function (PTF) with long tails in momentum space. The generalized Fokker-Planck equation for description of diffusion (in momentum space) of particles (ions, grains etc.) in a stochastic system of light particles (electrons, or electrons and ions, respectively) is applied to the evolution of the momentum particle distribution in a plasma. In a plasma the developed approach is also applicable to the diffusion of particles with an arbitrary mass relation, due to the small characteristic momentum transfer. The cases of an exponentially decreasing in momentum space (including the Boltzmann-like) kernel in the PT-function, as well as the more general kernels, which create the anomalous diffusion in velocity space due to the long tail in the PT-function, are considered. Effective friction and diffusion coefficients f...

Trigger, S A; van Heijst, G J F; Schram, P P J M; Sokolov, I M

2010-01-01T23:59:59.000Z

379

Detonation wave velocity and curvature of brass encased PBXN-111  

Science Conference Proceedings (OSTI)

Detonation velocities and wave front curvatures were measured for PBXN-111 charges encased in 5 mm thick brass tubes. In all the experiments (charge diameters from 19 to 47 mm) the brass case affected the detonation properties of PBXN-111. Steady detonation waves propagated in brass encased charges with diameters as small as 19 mm, which is about half of the unconfined failure diameter. The radii of curvature of the detonation waves at the center of the wave fronts ranged from 52 to 141 mm for charge diameters of 25 to 47 mm. The angles between the detonation wave fronts and the brass/charge interfaces were between 72 and 74 degrees. {copyright} {ital 1996 American Institute of Physics.}

Forbes, J.W.; Lemar, E.R. [Naval Surface Warfare Center, Indian Head Division, Silver Spring, Maryland 20903-5640 (United States)

1996-05-01T23:59:59.000Z

380

Acoustic-velocity measurements in materials using a regenerative method  

DOE Patents (OSTI)

Acoustic energy is propatated through earth material between an electro-acoustic generator and a receiver which converts the received acoustic energy into electrical signals. A closed loop is formed by a variable gain amplifier system connected between the receiver and the generator. The gain of the amplifier system is increased until sustained oscillations are produced in the closed loop. The frequency of the oscillations is measured as an indication of the acoustic propagation velocity through the earth material. The amplifier gain is measured as an indication of the acoustic attenuation through the earth materials. The method is also applicable to the non-destructive testing of structural materials, such as steel, aluminum and concrete.

Laine, E.F.

1982-09-30T23:59:59.000Z

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Acoustic velocity measurements in materials using a regenerative method  

DOE Patents (OSTI)

Acoustic energy is propagated through earth material between an electro-acoustic generator and a receiver which converts the received acoustic energy into electrical signals. A closed loop is formed by a variable gain amplifier system connected between the receiver and the generator. The gain of the amplifier system is increased until sustained oscillations are produced in the closed loop. The frequency of the oscillations is measured as an indication of the acoustic propagation velocity through the earth material. The amplifier gain is measured as an indication of the acoustic attenuation through the earth materials. The method is also applicable to the non-destructive testing of structural materials, such as steel, aluminum and concrete.

Laine, Edwin F. (Alamo, CA)

1986-01-01T23:59:59.000Z

382

Two-dimensional Imaging Velocity Interferometry: Technique and Data Analysis  

Science Conference Proceedings (OSTI)

We describe the data analysis procedures for an emerging interferometric technique for measuring motion across a two-dimensional image at a moment in time, i.e. a snapshot 2d-VISAR. Velocity interferometers (VISAR) measuring target motion to high precision have been an important diagnostic in shockwave physics for many years Until recently, this diagnostic has been limited to measuring motion at points or lines across a target. We introduce an emerging interferometric technique for measuring motion across a two-dimensional image, which could be called a snapshot 2d-VISAR. If a sufficiently fast movie camera technology existed, it could be placed behind a traditional VISAR optical system and record a 2d image vs time. But since that technology is not yet available, we use a CCD detector to record a single 2d image, with the pulsed nature of the illumination providing the time resolution. Consequently, since we are using pulsed illumination having a coherence length shorter than the VISAR interferometer delay ({approx}0.1 ns), we must use the white light velocimetry configuration to produce fringes with significant visibility. In this scheme, two interferometers (illuminating, detecting) having nearly identical delays are used in series, with one before the target and one after. This produces fringes with at most 50% visibility, but otherwise has the same fringe shift per target motion of a traditional VISAR. The 2d-VISAR observes a new world of information about shock behavior not readily accessible by traditional point or 1d-VISARS, simultaneously providing both a velocity map and an 'ordinary' snapshot photograph of the target. The 2d-VISAR has been used to observe nonuniformities in NIF related targets (polycrystalline diamond, Be), and in Si and Al.

Erskine, D J; Smith, R F; Bolme, C; Celliers, P; Collins, G

2011-03-23T23:59:59.000Z

383

Air Pollution Control (Oklahoma) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Air Pollution Control (Oklahoma) Air Pollution Control (Oklahoma) Air Pollution Control (Oklahoma) < Back Eligibility Agricultural Fuel Distributor Industrial Investor-Owned Utility Local Government Municipal/Public Utility Rural Electric Cooperative State/Provincial Govt Systems Integrator Tribal Government Utility Savings Category Buying & Making Electricity Program Info State Oklahoma Program Type Environmental Regulations Provider Environmental Quality This chapter enumerates primary and secondary ambient air quality standards and the significant deterioration increments. Significant deterioration refers to an increase in ambient air pollution above a baseline plus a specific increment allowed for one of three classes of areas. It is required for potential sources of air contaminants to register with the

384

AIR FORCE SPECIAL WEAPONS CENTER  

Office of Legacy Management (LM)

HEADQUARTERS aII?y HEADQUARTERS aII?y 9 AIR FORCE SPECIAL WEAPONS CENTER 1 AIR FORCE SYSTEMS COMMAND . - KlRTlAND AIR FORCE BASE, NEW MEXICO - k FINAL REPORT O N AIR FORCE PARTICIPATION PROJECT RULISON .1 O c t o b e r 1969 P r e p a r e d by : CONT INENTAL TEST D I V I S ION DIRECTORATE OF NUCLEAR FIELD OPERATIONS This page intentionally left blank INDEX AIR FORCE PARTICIPATION I N PROJECT RULISON FINAL REPORT PARAGRAPH BASIC REPORT SUBJECT R e f e r e n c e s PAGE 2 G e n e r a l 1 3 P l a n n i n g 3 4 Command a n d C o n t r o l 5 O p e r a t i o n s , G r a n d ' J u n c t i o n M u n i c i p a l A i r p o r t . . ' A i r O p e r a t i o n s C e n t e r , He1 i c o p t e r P a d / ' 7.. - . M a t e r i e l : ' 8 M e d i c a l 1 9 R a d - S a f e C r a s h - R e s c u e S e c u r i t y 2 1 C o m m u n i c a t i o n s ~ d m i n i s t r a t ' i o n Summary ATTACHMENTS ATTACHMENT SUBJECI' 1 F r a g O r d e r 69-1 ( ~ r o j ' e c t RULISON) , AFSWC D

385

Screw Air Compressor 220v, Screw Air Compressor 220v Suppliers ...  

U.S. Energy Information Administration (EIA)

Source Top Quality Screw Air Compressor 220v Suppliers, screw mini air compressor 220v Companies, atlas copco screw compressor Manufacturers. Welcome. ...

386

Air sampling in the workplace. Final report  

Science Conference Proceedings (OSTI)

This report provides technical information on air sampling that will be useful for facilities following the recommendations in the NRC`s Regulatory Guide 8.25, Revision 1, ``Air sampling in the Workplace.`` That guide addresses air sampling to meet the requirements in NRC`s regulations on radiation protection, 10 CFR Part 20. This report describes how to determine the need for air sampling based on the amount of material in process modified by the type of material, release potential, and confinement of the material. The purposes of air sampling and how the purposes affect the types of air sampling provided are discussed. The report discusses how to locate air samplers to accurately determine the concentrations of airborne radioactive materials that workers will be exposed to. The need for and the methods of performing airflow pattern studies to improve the accuracy of air sampling results are included. The report presents and gives examples of several techniques that can be used to evaluate whether the airborne concentrations of material are representative of the air inhaled by workers. Methods to adjust derived air concentrations for particle size are described. Methods to calibrate for volume of air sampled and estimate the uncertainty in the volume of air sampled are described. Statistical tests for determining minimum detectable concentrations are presented. How to perform an annual evaluation of the adequacy of the air sampling is also discussed.

Hickey, E.E.; Stoetzel, G.A.; Strom, D.J.; Cicotte, G.R. [Pacific Northwest Lab., Richland, WA (United States); Wiblin, C.M. [Advanced Systems Technology, Inc., Atlanta, GA (United States); McGuire, S.A. [Nuclear Regulatory Commission, Washington, DC (United States). Div. of Regulatory Applications

1993-09-01T23:59:59.000Z

387

TANGO ARRAY An Air Shower Experiment in Buenos Aires  

E-Print Network (OSTI)

A new Air Shower Observatory has been constructed in Buenos Aires during 1999, and commissioned and set in operation in 2000. The observatory consists of an array of four water \\v{C}erenkov detectors, enclosing a geometrical area of $\\sim$ 30.000 m$^{2}$, and is optimized for the observation of cosmic rays in the ``knee'' energy region. The array detects $\\sim$ 250 to $\\sim$ 1500 showers/day, depending on the selected triggering condition. In this paper, the design and construction of the array, and the automatic system for data adquisition, daily calibration, and monitoring, are described. Also, the Monte Carlo simulations performed to develop a shower database, as well as the studies performed using the database to estimate the response and the angular and energy resolutions of the array, are presented in detail.

P. Bauleo; C. Bonifazi; A. Filevich; A. Reguera

2001-04-20T23:59:59.000Z

388

Simulation model air-to-air plate heat exchanger  

Science Conference Proceedings (OSTI)

A simple simulation model of an air-to-air plate heat exchanger is presented. The model belongs to a collection of simulation models that allows the eflcient computer simulation of heating, ventilation, and air-conditioning (HVAC) systems. The main emphasis of the models is to shorten computation time and to use only input data that are known in the design process of an HVAC system. The target of the models is to describe the behavior of HVAC components in the part-load operation mode, which is becoming increasingly important in energy eficient HVAC systems. The models are intended to be used for yearly energy calculations or load calculations with time steps of about 10 minutes or larger. Short- time dynamic effects, which are of interest for different aspects of control theory, are neglected. The part-load behavior is expressed in terms of the nominal condition and the dimensionless variation of the heat transfer with change of mass flow and temperature. The effectiveness- NTU relations are used to parametrize the convective heat transfer at nominal conditions and to compute the part-load condition. If the heat transfer coefficients on the two exchanger sides are not equal (i. e. due to partial bypassing of air), their ratio can be easily calculated and set as a parameter. The model is static and uses explicit equations only. The explicit model formulation ensures short computation time and numerical stability, which allows using the model with sophisticated engineering methods like automatic system optimization. This paper fully outlines the algorithm description and its simplifications. It is not tailored for any particular simulation program to ensure easy implementation in any simulation program.

Wetter, Michael

1999-01-01T23:59:59.000Z

389

Air-Conditioning Basics | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Air-Conditioning Basics Air-Conditioning Basics Air-Conditioning Basics August 16, 2013 - 1:59pm Addthis Air conditioning is one of the most common ways to cool homes and buildings. How Air Conditioners Work Air conditioners employ the same operating principles and basic components as refrigerators. Refrigerators use energy (usually electricity) to transfer heat from the cool interior of the refrigerator to the relatively warm surroundings; likewise, an air conditioner uses energy to transfer heat from the interior space to the relatively warm outside environment. An air conditioner uses a cold indoor coil called the evaporator. The condenser, a hot outdoor coil, releases the collected heat outside. The evaporator and condenser coils are serpentine tubing surrounded by aluminum fins. This tubing is usually made of copper.

390

Evolution of US air cargo productivity  

E-Print Network (OSTI)

This thesis provides an overview of the US air cargo industry since airline deregulation in 1978, including a brief overview of the historical evolution of air cargo transport in the US from the early 1900s until the late ...

Donatelli, David J

2012-01-01T23:59:59.000Z

391

Detecting Air Leaks | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Detecting Air Leaks Detecting Air Leaks Detecting Air Leaks September 27, 2012 - 6:39pm Addthis For a thorough and accurate measurement of air leakage in your home, hire a qualified technician to conduct an energy assessment, particularly a blower door test. For a thorough and accurate measurement of air leakage in your home, hire a qualified technician to conduct an energy assessment, particularly a blower door test. You may already know where some air leakage occurs in your home, such as an under-the-door draft, but you'll need to find the less obvious gaps to properly air seal your home. For a thorough and accurate measurement of air leakage in your home, hire a qualified technician to conduct an energy assessment, particularly a blower door test. A blower door test, which depressurizes a home, can

392

Improving Regional Air Quality with Wind Power  

Wind Powering America (EERE)

Improving Regional Air Quality with Improving Regional Air Quality with Wind Power National Renewable Energy Laboratory Improving Regional Air Quality with Wind Power National Renewable Energy Laboratory * Clean Air Act (CAA) framework * Air quality challenges * CAA policies as market drivers * Met. Wash. Council of Governments (MWCOG) case study * Environmental Protection Agency (EPA) guidance on State Implementation Plan (SIP) credit for EERE * Model SIP documentation for wind purchases * Related marketing innovations Overview Overview * CAA requires regional air quality plans (SIPs) * "Window of opportunity" - Revised SIPs required by 2006/2007 to meet new 8-hour ozone and PM standards - August 2004 EPA guidance and NREL model SIP documentation for wind purchases Clean Air Act Framework Clean Air Act Framework

393

Protective supplied-breathing-air garment  

DOE Patents (OSTI)

A breathing-air garment for isolating a wearer from hostile environments containing toxins or irritants is disclosed. The garment includes a suit and a separate head-protective enclosure or hood engaging a suit collar in sealing attachment. The hood and suit collar are cylindrically shaped and dimensioned to enable the wearer to withdraw his hands from the suit sleeves to perform manual tasks within the hood interior. Breathing air is supplied from an external air line with an air-delivery hose attached to the hood interior. The hose feeds air into an annular halo-like fiber-filled plenum having spaced discharge orifices attached to the hood top wall. A plurality of air exhaust/check valves located at the suit extremities cooperate with the hood air-delivery system to provide a cooling flow of circulating air from the hood throughout the suit interior. A suit entry seal provided on the suit sealed with an adhesive sealing flap.

Childers, E.L.; von Hortenau, E.F.

1982-05-28T23:59:59.000Z

394

Duct/Air sealing | Open Energy Information  

Open Energy Info (EERE)

Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon DuctAir sealing Jump to: navigation, search TODO: Add description List of DuctAir sealing...

395

Catalysts for Destruction of Air Pollutants  

NLE Websites -- All DOE Office Websites (Extended Search)

Destruction of Air Pollutants Catalysts for Destruction of Air Pollutants U.S. industries and the U.S. Department of Energy must manage a variety of off-gas wastes consisting of...

396

Air Pollution Control Rules (West Virginia)  

Energy.gov (U.S. Department of Energy (DOE))

The listed rules were enacted as directed by the Air Pollution Control Act. Together, these rules guide the monitoring, permitting and compliance enforcement of air quality in the state.

397

Quantifying Precipitation Suppression Due to Air Pollution  

Science Conference Proceedings (OSTI)

Urban air pollution and industrial air pollution have been shown qualitatively to suppress rain and snow. Here, precipitation losses over topographical barriers downwind of major coastal urban areas in California and in the land of Israel that ...

Amir Givati; Daniel Rosenfeld

2004-07-01T23:59:59.000Z

398

Room Air Conditioners | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

you need to mount the air conditioner at the narrow end of a long room, then look for a fan control known as "Power Thrust" or "Super Thrust" that sends the cooled air farther...

399

Seneca Compressed Air Energy Storage (CAES) Project  

DOE Green Energy (OSTI)

This document provides specifications for the process air compressor for a compressed air storage project, requests a budgetary quote, and provides supporting information, including compressor data, site specific data, water analysis, and Seneca CAES value drivers.

None

2012-11-30T23:59:59.000Z

400

Ambient Air Quality Criteria (Manitoba, Canada)  

Energy.gov (U.S. Department of Energy (DOE))

The Manitoba Ambient Air Quality Criteria schedule lists maximum time-based pollutant concentration levels for the protection and preservation of ambient air quality within the Province of Manitoba...

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

ARM - Campaign Instrument - dri-air  

NLE Websites -- All DOE Office Websites (Extended Search)

Send Campaign Instrument : Desert Research Institute Airborne Aerosol Instruments (DRI-AIR) Instrument Categories Aerosols, Airborne Observations Campaigns Aerosol IOP ...

402

South Coast Air Quality Management District  

Science Conference Proceedings (OSTI)

South Coast Air Quality Management District. NVLAP Lab Code: 101567-0. Address and Contact Information: 21865 Copley ...

2013-08-09T23:59:59.000Z

403

Do filters pollute the air? Part 1  

E-Print Network (OSTI)

Air Infiltration Glossary-Italian Edition. TechnicalNote AIC 5.3]. Glossary-Italian Edition. Technical Note AIC

Bek, Gabriel; Schiavon, Stefano

2008-01-01T23:59:59.000Z

404

AIR LEAKAGE OF NEWLY INSTALLED RESIDENTIAL WINDOWS  

E-Print Network (OSTI)

Through Sash/Frame Cracks . Window Operation Types . . . . .Window Operation Types . . . . .Air Leakage of Installed Windows Scattergram of Field

Weidt, John

2013-01-01T23:59:59.000Z

405

The stabilization of a methane-air edge flame within a mixing layer in a narrow channel  

SciTech Connect

The flame stabilization mechanism of a methane-air edge flame formulated in a narrow channel was experimentally investigated and compared with a simple analytical model. Non-premixed flames were classified into premixed flame modes and edge flame modes. The correlation between the propagation velocity and the fuel concentration gradient in a narrow channel was investigated and the applicability of ordinary edge-flame theory was appraised. (author)

Lee, Min Jung; Kim, Nam Il [School of Mechanical Engineering, Chung-Ang University, Dongjak, Seoul 156-76 (Korea)

2010-01-15T23:59:59.000Z

406

Analysis of U.S. residential air leakage database  

E-Print Network (OSTI)

installing air and vapor barriers, and sealing ducts.that will reduce air in?ltration such as sealing air leaks,

Chan, Wanyu R.; Price, Phillip N.; Sohn, Michael D.; Gadgil, Ashok J.

2003-01-01T23:59:59.000Z

407

Fact Sheet: Isothermal Compressed Air Energy Storage (October...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Isothermal Compressed Air Energy Storage (October 2012) Fact Sheet: Isothermal Compressed Air Energy Storage (October 2012) SustainX will demonstrate an isothermal compressed air...

408

Investigation of residential central air conditioning load shapes in NEMS  

E-Print Network (OSTI)

of Residential Central Air Conditioning Load Shapes in NEMSof Residential Central Air Conditioning Load Shapes in NEMSof Residential Central Air Conditioning Load Shapes in NEMS

Hamachi LaCommare, Kristina; Marnay, Chris; Gumerman, Etan; Chan, Peter; Rosenquist, Greg; Osborn, Julie

2002-01-01T23:59:59.000Z

409

Performance of underfloor air distribution: Results of a field study  

E-Print Network (OSTI)

Refrigerating, and Air Conditioning Engineers. AtlantaRefrigerating, and Air Conditioning Engineers. AtlantaRefrigerating, and Air-Conditioning Engineers, Inc. ,

Fisk, William; Faulkner, David; Sullivan, Douglas

2004-01-01T23:59:59.000Z

410

Air Products Hydrogen Energy Systems | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Air Products Hydrogen Energy Systems Air Products Hydrogen Energy Systems Hydrogen Infrastructure Air Products Hydrogen Energy Systems More Documents & Publications Quadrennial...

411

Shale Gas Development Challenges: Air | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Shale Gas Development Challenges: Air Shale Gas Development Challenges: Air Shale Gas Development Challenges: Air More Documents & Publications Natural Gas from Shale: Questions...

412

buy Adekom VSD Air Compressor - high quality Manufacturers ...  

U.S. Energy Information Administration (EIA)

Adekom VSD Air Compressor trade offers directory and Adekom VSD Air Compressor business offers list. Trade leads from Adekom VSD Air Compressor ...

413

NETL: Air Quality III Conference  

NLE Websites -- All DOE Office Websites (Extended Search)

Air Quality III Conference - September 12, 2002 Air Quality III Conference - September 12, 2002 Table of Contents Disclaimer Papers and Presentations Disclaimer This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government or any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States Government or any agency thereof. The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States Government or any agency thereof.

414

Airvest's Breath of Fresh Air  

NLE Websites -- All DOE Office Websites (Extended Search)

7 7 The Cutting Edge: Airvest's Breath of Fresh Air Spray booths are a common sight in the industrial sector. Designed to remove pollutants during industrial processes such as spray painting or welding, a booth is a rectangular enclosure open on one side where the worker stands, and equipped on the opposite wall with a fan and filter arrangement to suck away the dirty air. The full-size mannequin in these photographs simulates a worker in a spray booth facing the exhaust filters. In experiments designed by LBL researcher Ashok Gadgil, smoke was released in front of the mannequin to simulate the spraying of paint in the booth. The photo on the left shows the spray booth during standard operation. The smoke-representing a pollutant-is entrained in the eddy that forms in

415

Capturing Carbon Dioxide From Air  

NLE Websites -- All DOE Office Websites (Extended Search)

Capturing Carbon Dioxide From Air Capturing Carbon Dioxide From Air Klaus S. Lackner (kl2010@columbia.edu; 212-854-0304) Columbia University 500 West 120th Street New York, NY 10027 Patrick Grimes (pgrimes@worldnet.att.net; 908-232-1134) Grimes Associates Scotch Plains, NJ 07076 Hans-J. Ziock (ziock@lanl.gov; 505-667-7265) Los Alamos National Laboratory P.O.Box 1663 Los Alamos, NM 87544 Abstract The goal of carbon sequestration is to take CO 2 that would otherwise accumulate in the atmosphere and put it in safe and permanent storage. Most proposed methods would capture CO 2 from concentrated sources like power plants. Indeed, on-site capture is the most sensible approach for large sources and initially offers the most cost-effective avenue to sequestration. For distributed, mobile sources like cars, on-board capture at affordable cost would not be

416

Clean Air Act, Section 309  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CLEAN AIR ACT § 309* CLEAN AIR ACT § 309* §7609. Policy review (a) The Administrator shall review and comment in writing on the environmental impact of any matter relating to duties and responsibilities granted pursuant to this chapter or other provisions of the authority of Administrator, contained in any (1) legislation proposed by any Federal department or agency, (2) newly authorized Federal projects for construction and any major Federal agency action (other than a project for construction) to which section 4332(2)(C) of this title applies, and (3) proposed regulations published by any department or agency of the Federal Government. Such written comment shall be made public at the conclusion of any such review. (b) In the event the Administrator determines that any such legislation, action, or regulation

417

Air pollution and lung cancer  

SciTech Connect

Epidemiological evidence proves conclusively that lung cancer correlates with air pollution. However, data on lung cancer death rates and smoking show that mankind accepts the risk of long-term and low-level exposure to carcinogens. As a rule, immediate benefits are sought and remote hazards ignored. Fear of atmospheric contamination by radioactive fallout seems to be the main factor for awareness of air pollution. Experimental works help us to understand physics of particle deposition in the lungs (inertial impactation, sedimentation, Brownian movement), shed light on carcinogenesis (eg, bay region theory in case of polycyclic aromatic hydrocarbons and surface charge changes regarding asbestos), show that atmospheric particulates accepted as harmless may act as co-carcinogens (eg, iron and benzo(a)pyrene) and stress the importance of in vitro research (bacterial mutation tests, organ cultures, sister chromatid exchange system) to screen pollutants for their malignant potential and study their pathogenesis.

Boehm, G.M.

1982-01-01T23:59:59.000Z

418

Compressed Air Audits using AIRMaster  

E-Print Network (OSTI)

Air compressors are a significant industrial energy user and therefore a prime target for industrial energy audits. The project goal was to develop a software tool, AIRMaster, and supporting methodology for performing compressed air system audits. Seven field audits were conducted to refine the software and methodology as well as assess the savings potential of six common Operation and Maintenance measures. Audit results yielded significant savings with short payback periods. Total estimated savings for the project were 4,056,000 kWh or 49.2% of annual compressor energy for a cost savings of $152,000. Total implementation costs were $94,700 for a project payback period of 0.6 years. Capital benefits of delaying or avoiding the cost of a new compressor might double the energy benefits if a new compressor is being considered. The methodology proved to be a simple and effective audit tool.

Wheeler, G. M.; McGill, R. D.; Bessey, E. G.; Vischer, K.

1997-04-01T23:59:59.000Z

419

Longshore sediment transport rate calculated incorporating wave orbital velocity fluctuations  

E-Print Network (OSTI)

Laboratory experiments were performed to study and improve longshore sediment transport rate predictions. Measured total longshore transport in the laboratory was approximately three times greater for plunging breakers than spilling breakers. Three distinct zones of longshore transport were observed across the surf zone: the incipient breaker zone, inner surf zone, and swash zone. Transport at incipient breaking was influenced by breaker type; inner surf zone transport was dominated by wave height, independent of wave period; and swash zone transport was dependent on wave period. Selected predictive formulas to compute total load and distributed load transport were compared to laboratory and field data. Equations by Kamphuis (1991) and Madsen et al. (2003) gave consistent total sediment transport estimates for both laboratory and field data. Additionally, the CERC formula predicted measurements well if calibrated and applied to similar breaker types. Each of the distributed load models had shortcomings. The energetics model of Bodge and Dean (1987) was sensitive to fluctuations in energy dissipation and often predicted transport peaks that were not present in the data. The Watanabe (1992) equation, based on time-averaged bottom stress, predicted no transport at most laboratory locations. The Van Rijn (1993) model was comprehensive and required hydrodynamic, bedform, and sediment data. The model estimated the laboratory cross-shore distribution well, but greatly overestimated field transport. Seven models were developed in this study based on the principle that transported sediment is mobilized by the total shear stress acting on the bottom and transported by the current at that location. Shear stress, including the turbulent component, was calculated from the wave orbital velocity. Models 1 through 3 gave good estimates of the transport distribution, but underpredicted the transport peak near the plunging wave breakpoint. A suspension term was included in Models 4 through 7, which improved estimates near breaking for plunging breakers. Models 4, 5 and 7 also compared well to the field measurements. It was concluded that breaker type is an important variable in determining the amount of transport that occurs at a location. Lastly, inclusion of the turbulent component of the orbital velocity is vital in predictive sediment transport equations.

Smith, Ernest Ray

2006-08-01T23:59:59.000Z

420

Zoned heating and air conditioning system  

SciTech Connect

This patent describes a zoned heating and air conditioning system comprising: a central air handling system with an air heating means and an air cooling means and a blower connected to an air duct system; thermostats each have heating and cooling set points, respectively associated with and located in different zones of a building; dampers respectively associated with each building zone positioned in the air duct system. Each damper has an open position allowing air into the respective zone from the duct system and a closed position; relay means for connecting one thermostat to the air handling system upon a call for heating or cooling by one thermostat and disconnecting all other thermostats by connecting one thermostat's connections between the thermostat and air handling system. Only one thermostat is connected to the air handling system at a time and the relay means disconnects one thermostat from the air handling system after one thermostat is satisified; and damper actuating means for unlocking each damper in one building zone responsive actuated by a respective zone thermostat connected to the air handling system by the relay means. The damper actuates means including a damper solenoid for each damper located adjacent each damper and connected to a respective zone thermostat. It unlocks each damper in one building zone responsive to being actuated by the respective zone thermostat and unlocks the dampers in one building zone when one thermostat is actuated while preventing the dampers in another thermostat's building zone from unlocking.

Beachboard, S.A.

1987-06-16T23:59:59.000Z

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Strategy Guideline: Compact Air Distribution Systems  

SciTech Connect

This Strategy Guideline discusses the benefits and challenges of using a compact air distribution system to handle the reduced loads and reduced air volume needed to condition the space within an energy efficient home. Traditional systems sized by 'rule of thumb' (i.e., 1 ton of cooling per 400 ft2 of floor space) that 'wash' the exterior walls with conditioned air from floor registers cannot provide appropriate air mixing and moisture removal in low-load homes. A compact air distribution system locates the HVAC equipment centrally with shorter ducts run to interior walls, and ceiling supply outlets throw the air toward the exterior walls along the ceiling plane; alternatively, high sidewall supply outlets throw the air toward the exterior walls. Potential drawbacks include resistance from installing contractors or code officials who are unfamiliar with compact air distribution systems, as well as a lack of availability of low-cost high sidewall or ceiling supply outlets to meet the low air volumes with good throw characteristics. The decision criteria for a compact air distribution system must be determined early in the whole-house design process, considering both supply and return air design. However, careful installation of a compact air distribution system can result in lower material costs from smaller equipment, shorter duct runs, and fewer outlets; increased installation efficiencies, including ease of fitting the system into conditioned space; lower loads on a better balanced HVAC system, and overall improved energy efficiency of the home.

Burdick, A.

2013-06-01T23:59:59.000Z

422

Intelligent pairing assistant for air operation centers  

Science Conference Proceedings (OSTI)

Within an Air Operations Center (AOC), planners make crucial decisions to create the air plan for any given day. They are expected to complete the plan in part by pairing targeting or collection tasks with the available platforms. Any assistance these ... Keywords: air operations center, intelligent user interface, pairing, reinforcement learning

Jeremy Ludwig; Eric Geiselman

2012-02-01T23:59:59.000Z

423

Air breathing direct methanol fuel cell  

DOE Patents (OSTI)

An air breathing direct methanol fuel cell is provided with a membrane electrode assembly, a conductive anode assembly that is permeable to air and directly open to atmospheric air, and a conductive cathode assembly that is permeable to methanol and directly contacting a liquid methanol source.

Ren, Xiaoming (Los Alamos, NM)

2002-01-01T23:59:59.000Z

424

Workshop on indoor air quality research needs  

Science Conference Proceedings (OSTI)

Workshop participants report on indoor air quality research needs including the monitoring of indoor air quality, report of the instrumentation subgroup of indoor air quality, health effects, and the report of the control technology session. Risk analysis studies addressing indoor environments were also summarized. (DLS)

Not Available

1980-01-01T23:59:59.000Z

425

Air Conditioner Compressor Performance Model  

SciTech Connect

During the past three years, the Western Electricity Coordinating Council (WECC) Load Modeling Task Force (LMTF) has led the effort to develop the new modeling approach. As part of this effort, the Bonneville Power Administration (BPA), Southern California Edison (SCE), and Electric Power Research Institute (EPRI) Solutions tested 27 residential air-conditioning units to assess their response to delayed voltage recovery transients. After completing these tests, different modeling approaches were proposed, among them a performance modeling approach that proved to be one of the three favored for its simplicity and ability to recreate different SVR events satisfactorily. Funded by the California Energy Commission (CEC) under its load modeling project, researchers at Pacific Northwest National Laboratory (PNNL) led the follow-on task to analyze the motor testing data to derive the parameters needed to develop a performance models for the single-phase air-conditioning (SPAC) unit. To derive the performance model, PNNL researchers first used the motor voltage and frequency ramping test data to obtain the real (P) and reactive (Q) power versus voltage (V) and frequency (f) curves. Then, curve fitting was used to develop the P-V, Q-V, P-f, and Q-f relationships for motor running and stalling states. The resulting performance model ignores the dynamic response of the air-conditioning motor. Because the inertia of the air-conditioning motor is very small (H<0.05), the motor reaches from one steady state to another in a few cycles. So, the performance model is a fair representation of the motor behaviors in both running and stalling states.

Lu, Ning; Xie, YuLong; Huang, Zhenyu

2008-09-05T23:59:59.000Z

426

Residential Indoor Air Background Data  

Science Conference Proceedings (OSTI)

Soil vapor intrusion, the migration of volatile chemicals from contaminated soil or groundwater into overlying buildings, has become one of the primary exposure pathways of concern for state and federal environmental agencies regulating contaminated sites in the USA. Regulators are requesting comprehensive evaluation of the subsurface vapor-to-indoor air pathway for currently occupied buildings, areas which may be developed in the future, and closed sites for which this pathway was not previously evaluat...

2007-03-16T23:59:59.000Z

427

Clean Air Act. Revision 5  

SciTech Connect

This Reference Book contains a current copy of the Clean Air Act, as amended, and those regulations that implement the statute and appear to be most relevant to DOE activities. The document is provided to DOE and contractor staff for informational purposes only and should not be interpreted as legal guidance. This Reference Book has been completely revised and is current through February 15, 1994.

Not Available

1994-02-15T23:59:59.000Z

428

Hybrid regional air pollution models  

SciTech Connect

This discussion deals with a family of air quality models for predicting and analyzing the fine particulate loading in the atmosphere, for assessing the extent and degree of visibility impairment, and for determining the potential of pollutants for increasing the acidity of soils and water. The major horizontal scales of interest are from 400km to 2000km; and the time scales may vary from several hours, to days, weeks, and a few months or years, depending on the EPA regulations being addressed. First the role air quality models play in the general family of atmospheric simulation models is described. Then, the characteristics of a well-designed, comprehensive air quality model are discussed. Following this, the specific objectives of this workshop are outlined, and their modeling implications are summarized. There are significant modeling differences produced by the choice of the coordinate system, whether it be the fixed Eulerian system, the moving Lagrangian system, or some hybrid of the two. These three systems are briefly discussed, and a list of hybrid models that are currently in use are given. Finally, the PNL regional transport model is outlined and a number of research needs are listed.

Drake, R.L.

1980-03-01T23:59:59.000Z

429

Teleseismic evidence for a low-velocity body under the Coso geothermal area  

Open Energy Info (EERE)

Teleseismic evidence for a low-velocity body under the Coso geothermal area Teleseismic evidence for a low-velocity body under the Coso geothermal area Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Teleseismic evidence for a low-velocity body under the Coso geothermal area Details Activities (1) Areas (1) Regions (0) Abstract: Teleseismic P wave arrivals were recorded by a dense array of seismograph stations located in the Coso geothermal area, California. The resulting pattern of relative residuals an area showing approximately 0.2-s excess travel time that migrates with changing source azimuth, suggesting that the area is the 'delay shadow' produced by a deep, low-velocity body. Inversion of the relative residual data for three-dimensional velocity structure determines the lateral variations in velocity to a depth of 22.5

430

Air Corrosivity in U.S. Outdoor-Air-Cooled Data Centers is Similar to That  

NLE Websites -- All DOE Office Websites (Extended Search)

Air Corrosivity in U.S. Outdoor-Air-Cooled Data Centers is Similar to That Air Corrosivity in U.S. Outdoor-Air-Cooled Data Centers is Similar to That in Conventional Data Centers Title Air Corrosivity in U.S. Outdoor-Air-Cooled Data Centers is Similar to That in Conventional Data Centers Publication Type Report LBNL Report Number LBNL-4951E Year of Publication 2011 Authors Coles, Henry C., Tae Won Han, Phillip N. Price, Ashok J. Gadgil, and William F. Tschudi Date Published 03/2011 Abstract There is a concern that environmental-contamination caused corrosion may negatively affect Information Technology (IT) equipment reliability. Nineteen data centers in the United States and two in India were evaluated using Corrosion Classification Coupons (CCC) to assess environmental air quality as it may relate IT equipment reliability. The data centers were of two basic types: "closed" and outside-air cooled. A closed data center provides cool air to the IT equipment using air conditioning in which only a small percentage of the recirculation air is "make-up" air continuously supplied from outside to meet human health requirements. An outside-air cooled data center uses outside air directly as the primary source for IT equipment cooling. Corrosion measuring coupons containing copper and silver metal strips were placed in both "closed" and outside-air cooled data centers. The coupons were placed at each data center (closed and outside-air cooled types) with the location categorized into three groups:

431

Laboratory Study of Premixed H2-Air and H2-N2-Air Flames in a...  

NLE Websites -- All DOE Office Websites (Extended Search)

of Premixed H2-Air and H2-N2-Air Flames in a Low-Swirl Injector for Ultra-Low Emissions Gas Turbines Title Laboratory Study of Premixed H2-Air and H2-N2-Air Flames in a Low-Swirl...

432

Sensitivity of forced air distribution system efficiency to climate, duct location, air leakage and insulation  

E-Print Network (OSTI)

Location, Air Leakage and Insulation Iain S. Walker Energy4 Duct Insulation, Location and Leakageinsulation

Walker, Iain

2001-01-01T23:59:59.000Z

433

Stochastic velocity motions and processes with random time  

E-Print Network (OSTI)

The aim of this paper is to analyze a class of random motions which models the motion of a particle on the real line with random velocity and subject to the action of the friction. The speed randomly changes when a Poissonian event occurs. We study the characteristic and the moment generating function of the position reached by the particle at time $t>0$. We are able to derive the explicit probability distributions in few cases for which discuss the connections with the random flights. The moments are also widely analyzed. For the random motions having an explicit density law, further interesting probabilistic interpretations emerge if we deal with them varying up a random time. Essentially, we consider two different type of random times, namely Bessel and Gamma times, which contain, as particular cases, some important probability distributions (e.g. Gaussian, Exponential). In particular, for the random processes built by means of these compositions, we derive the probability distributions fixed the number of...

De Gregorio, Alessandro

2009-01-01T23:59:59.000Z

434

Radiation Hydrodynamics Test Problems with Linear Velocity Profiles  

Science Conference Proceedings (OSTI)

As an extension of the works of Coggeshall and Ramsey, a class of analytic solutions to the radiation hydrodynamics equations is derived for code verification purposes. These solutions are valid under assumptions including diffusive radiation transport, a polytropic gas equation of state, constant conductivity, separable flow velocity proportional to the curvilinear radial coordinate, and divergence-free heat flux. In accordance with these assumptions, the derived solution class is mathematically invariant with respect to the presence of radiative heat conduction, and thus represents a solution to the compressible flow (Euler) equations with or without conduction terms included. With this solution class, a quantitative code verification study (using spatial convergence rates) is performed for the cell-centered, finite volume, Eulerian compressible flow code xRAGE developed at Los Alamos National Laboratory. Simulation results show near second order spatial convergence in all physical variables when using the hydrodynamics solver only, consistent with that solver's underlying order of accuracy. However, contrary to the mathematical properties of the solution class, when heat conduction algorithms are enabled the calculation does not converge to the analytic solution.

Hendon, Raymond C. [Los Alamos National Laboratory; Ramsey, Scott D. [Los Alamos National Laboratory

2012-08-22T23:59:59.000Z

435

Velocity distribution measurements in atomic beams generated using laser induced back-ablation  

E-Print Network (OSTI)

We present measurements of the velocity distribution of calcium atoms in an atomic beam generated using a dual-stage laser back-ablation apparatus. Distributions are measured using a velocity selective Doppler time-of-flight technique. They are Boltzmann-like with rms velocities corresponding to temperatures above the melting point for calcium. Contrary to a recent report in the literature, this method does not generate a sub-thermal atomic beam.

Denning, A; Lee, S; Ammonson, M; Bergeson, S D

2008-01-01T23:59:59.000Z

436

Recommended Tritium Oxide Deposition Velocity For Use In Savannah River Site Safety Analyses  

SciTech Connect

This report documents the results of examining the deposition velocity of water to forests, the residence time of HTO in forests, and the relation between deposition velocity and residence time with specific consideration given to the topography and experimental work performed at SRS. A simple mechanistic model is used to obtain plausible deposition velocity and residence time values where experimental data are not available and recommendations are made for practical application in a safety analysis model.

Lee, P. L.; Murphy, C. E.; Viner, B. J.; Hunter, C. H.

2012-07-31T23:59:59.000Z

437

One-loop fluctuation-dissipation formula for bubble-wall velocity  

Science Conference Proceedings (OSTI)

The limiting bubble wall velocity during a first-order electroweak phase transition is of interest in scenarios for electroweak baryogenesis. Khlebnikov has recently proposed an interesting method for computing this velocity based on the fluctuation-dissipation theorem. It is demonstrated that at one-loop order this method is identical to simple, earlier techniques for computing the wall velocity based on computing the friction from particles reflecting off or transmitting through the wall in the ideal gas limit.

Arnold, P.

1993-06-01T23:59:59.000Z

438

RECOMMENDED TRITIUM OXIDE DEPOSITION VELOCITY FOR USE IN SAVANNAH RIVER SITE SAFETY ANALYSES  

Science Conference Proceedings (OSTI)

This report documents the results of examining the deposition velocity of water to forests, the residence time of HTO in forests, and the relation between deposition velocity and residence time with specific consideration given to the topography and experimental work performed at SRS. A simple mechanistic model is used to obtain plausible deposition velocity and residence time values where experimental data are not available and recommendations are made for practical application in a safety analysis model.

Lee, P.; Murphy, C.; Viner, B.; Jannik, T.; Hunter, C.; Moore, M.

2012-07-31T23:59:59.000Z

439

On the superficial gas velocity in deep gas-solids fluidized beds  

SciTech Connect

The superficial gas velocity is one of the key parameters used to determine the flow hydrodynamics in gassolids fluidized beds. However, the superficial velocity varies with height in practice, and there is no consistent basis for its specification. Different approaches to determine the superficial gas velocity in a deep gassolids system are shown to cause difficulties in developing models and in comparing predictions with experimental results. In addition, the reference conditions for superficial gas velocity are important in modeling of deep gassolids systems where there is a considerable pressure drop.

Li, Tingwen; Grace, John; Shadle, Lawrence; Guenther, Chris

2012-11-15T23:59:59.000Z

440

On the Superficial Gas Velocity in Deep Gas-Solid Fluidized Beds  

Science Conference Proceedings (OSTI)

The superficial gas velocity is one of the key parameters used to determine the flow hydrodynamics in gassolids fluidized beds. However, the superficial velocity varies with height in practice, and there is no consistent basis for its specification. Different approaches to determine the superficial gas velocity in a deep gassolids system are shown to cause difficulties in developing models and in comparing predictions with experimental results. In addition, the reference conditions for superficial gas velocity are important in modeling of deep gassolids systems where there is a considerable pressure drop.

Li, Tingwen; Grace, John; Shadle, Lawrence; Guenther, Chris

2011-11-15T23:59:59.000Z

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Force criterion prediction of damage for carbon/epoxy composite panels impacted by high velocity ice  

E-Print Network (OSTI)

H, Kedward, K. T. Modeling Hail Ice Impacts and PredictingInvestigation of High Velocity Ice Impacts on Woven Carbon/Analysis Correlation of Hail Ice Impacting Composite

Rhymer, Jennifer D.

2012-01-01T23:59:59.000Z

442

Analysis of a Dedicated Outdoor Air System and Low Temperature Supply Air Conditioning System  

E-Print Network (OSTI)

This paper presents the principles and the characteristics of a dedicated outdoor air system (DOAS) and low temperature supply air system. DOAS is offered based on the demands of indoor air quality and the low temperature supply air system is offered based on the demands of saving energy. The two systems are very similar, which is analyzed in this paper. Using actual engineering, we compute the air flow rate, cold load and energy consumption in detail, and provide some good conclusions.

Guang, L.; Li, R.

2006-01-01T23:59:59.000Z

443

Clean Air Act | Open Energy Information  

Open Energy Info (EERE)

Clean Air Act Clean Air Act Jump to: navigation, search Statute Name Clean Air Act Year 1970 Url CAA.jpg Description Congress passed the CAA in 1970 in order to combat air pollution in the United States and protect the health and general welfare of United States citizens against air pollutants. References CAA[1] Federal Oil and Gas[2] Contents 1 Introduction 2 Title I Air Pollution Prevention 3 Title II Emission Standards for Moving Sources 4 Title III General Provisions 5 Title IV Acid Deposition Control 6 Title V Permits 7 Title VI Stratospheric Ozone Protection 8 References Introduction The Clean Air Act was enacted by congress in 1990. Since then only minor changes have been made. The act is just a law ensuring that the EPA will follow certain guidelines and definitions for protecting and improving the

444

Tips: Air Conditioners | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Tips: Air Conditioners Tips: Air Conditioners Tips: Air Conditioners June 24, 2013 - 6:31pm Addthis Bigger isn't always better for an air conditioner. Learn effective ways to stay cool while saving energy. | Photo courtesy of ©iStockphoto/galinast. Bigger isn't always better for an air conditioner. Learn effective ways to stay cool while saving energy. | Photo courtesy of ©iStockphoto/galinast. Buying a bigger room air conditioner won't necessarily make you feel more comfortable during the hot summer months. In fact, a room air conditioner that's too big for the area it is supposed to cool will perform less efficiently and less effectively than a smaller, properly sized unit. The reason: an oversized unit will cool the room(s) to the thermostat set-point before proper dehumidification occurs, making the area feel "clammy"

445

Air Sealing Your Home | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Your Home Your Home Air Sealing Your Home November 26, 2013 - 6:22pm Addthis Save on heating and cooling costs by checking for air leaks in common trouble spots in your home. Save on heating and cooling costs by checking for air leaks in common trouble spots in your home. What does this mean for me? Save money and energy by air sealing your house. Caulking and weatherstripping are simple, effective ways of sealing air leaks in your home. Reducing the amount of air that leaks in and out of your home is a cost-effective way to cut heating and cooling costs, improve durability, increase comfort, and create a healthier indoor environment. Caulking and weatherstripping are two simple and effective air-sealing techniques that offer quick returns on investment, often one year or less. Caulk is

446

Air Products Chemicals Inc | Open Energy Information  

Open Energy Info (EERE)

Air Products Chemicals Inc Air Products Chemicals Inc Jump to: navigation, search Name Air Products & Chemicals Inc Place Allentown, Pennsylvania Zip 18195 Sector Hydro, Hydrogen, Services Product A global supplier of merchant hydrogen with a portfolio of products, services and solutions providing gases, performance materials and chemical intermediates. References Air Products & Chemicals Inc[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Air Products & Chemicals Inc is a company located in Allentown, Pennsylvania . References ↑ "Air Products & Chemicals Inc" Retrieved from "http://en.openei.org/w/index.php?title=Air_Products_Chemicals_Inc&oldid=341937

447

Tips: Air Conditioners | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Tips: Air Conditioners Tips: Air Conditioners Tips: Air Conditioners June 24, 2013 - 6:31pm Addthis Bigger isn't always better for an air conditioner. Learn effective ways to stay cool while saving energy. | Photo courtesy of ©iStockphoto/galinast. Bigger isn't always better for an air conditioner. Learn effective ways to stay cool while saving energy. | Photo courtesy of ©iStockphoto/galinast. Buying a bigger room air conditioner won't necessarily make you feel more comfortable during the hot summer months. In fact, a room air conditioner that's too big for the area it is supposed to cool will perform less efficiently and less effectively than a smaller, properly sized unit. The reason: an oversized unit will cool the room(s) to the thermostat set-point before proper dehumidification occurs, making the area feel "clammy"

448

Alpha-environmental continuous air monitor inlet  

DOE Patents (OSTI)

A wind deceleration and protective shroud that provides representative samples of ambient aerosols to an environmental continuous air monitor (ECAM) has a cylindrical enclosure mounted to an input on the continuous air monitor, the cylindrical enclosure having shrouded nozzles located radially about its periphery. Ambient air flows, often along with rainwater flows into the nozzles in a sampling flow generated by a pump in the continuous air monitor. The sampling flow of air creates a cyclonic flow in the enclosure that flows up through the cylindrical enclosure until the flow of air reaches the top of the cylindrical enclosure and then is directed downward to the continuous air monitor. A sloped platform located inside the cylindrical enclosure supports the nozzles and causes any moisture entering through the nozzle to drain out through the nozzles.

Rodgers, John C. (Santa Fe, NM)

2003-01-01T23:59:59.000Z

449

Industrial Compressed Air System Energy Efficiency Guidebook.  

DOE Green Energy (OSTI)

Energy efficient design, operation and maintenance of compressed air systems in industrial plants can provide substantial reductions in electric power and other operational costs. This guidebook will help identify cost effective, energy efficiency opportunities in compressed air system design, re-design, operation and maintenance. The guidebook provides: (1) a broad overview of industrial compressed air systems, (2) methods for estimating compressed air consumption and projected air savings, (3) a description of applicable, generic energy conservation measures, and, (4) a review of some compressed air system demonstration projects that have taken place over the last two years. The primary audience for this guidebook includes plant maintenance supervisors, plant engineers, plant managers and others interested in energy management of industrial compressed air systems.

United States. Bonneville Power Administration.

1993-12-01T23:59:59.000Z

450

Air-Con International: Noncompliance Determination and Proposed...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

to Air-Con International finding that a variety of central air conditioners and air conditioning heat pumps distributed under the Air-Con private label do not comport...

451

Air-Source Heat Pumps | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Air-Source Heat Pumps Air-Source Heat Pumps August 19, 2013 - 11:03am Addthis Air-source heat pumps transfer heat between the inside of a building and the outside air. How...

452

Hohlraum Designs for High Velocity Implosions on NIF  

Science Conference Proceedings (OSTI)

In this paper, we compare experimental shock and capsule trajectories to design calculations using the radiation-hydrodynamics code HYDRA. The measured trajectories from surrogate ignition targets are consistent with reducing the x-ray flux on the capsule by about 85%. A new method of extracting the radiation temperature as seen by the capsule from x-ray intensity and image data shows that about half of the apparent 15% flux deficit in the data with respect to the simulations can be explained by HYDRA overestimating the x-ray flux on the capsule. The National Ignition Campaign (NIC) point-design target is designed to reach a peak fuel-layer velocity of 370 km/s by ablating 90% of its plastic (CH) ablator. The 192-beam National Ignition Facility laser drives a gold hohlraum to a radiation temperature (T{sub RAD}) of 300 eV with a 20 ns-long, 420 TW, 1.3 MJ laser pulse. The hohlraum x-rays couple to the CH ablator in order to apply the required pressure to the outside of the capsule. In this paper, we compare experimental measurements of the hohlraum T{sub RAD} and the implosion trajectory with design calculations using the code hydra. The measured radial positions of the leading shock wave and the unablated shell are consistent with simulations in which the x-ray flux on the capsule is artificially reduced by 85%. We describe a new method of inferring the T{sub RAD} seen by the capsule from time-dependent x-ray intensity data and static x-ray images. This analysis shows that hydra overestimates the x-ray flux incident on the capsule by {approx}8%.

Meezan, N B; Hicks, D G; Callahan, D A; Olson, R E; Schneider, M S; Thomas, C A; Robey, H F; Celliers, P M; Kline, J K; Dixit, S N; Michel, P A; Jones, O S; Clark, D S; Ralph, J E; Doeppner, T; MacKinnon, A J; Haan, S W; Landen, O L; Glenzer, S H; Suter, L J; Edwards, M J; Macgowan, B J; Lindl, J D; Atherton, L J

2011-10-19T23:59:59.000Z

453

DEPOSITION VELOCITY ESTIMATION WITH THE GENII V2 SOFTWARE  

SciTech Connect

In 2010, the Department of Energy (DOE) Chief of Nuclear Safety and Office of Health, Safety and Security (HSS), with the support of industry experts in atmospheric sciences and accident dose consequences analysis, performed detailed analyses of the basis for the dry deposition velocity (DV) values used in the MACCS2 computer code. As a result of these analyses, DOE concluded that the historically used default DV values of 1 centimeter/second (cm/s) for unfiltered/unmitigated releases and 0.1 cm/s for filtered/mitigated releases may not be reasonably conservative for all DOE sites and accident scenarios. HSS recently issued Safety Bulletin 2011-02, Accident Analysis Parameter Update, recommending the use of the newly developed default DV, 0.1 cm/s for an unmitigated/unfiltered release. Alternatively site specific DV values can be developed using GENII version 2 (GENII v2) computer code. Key input parameters for calculating DV values include surface roughness, maximum wind speed for calm, particle size, particle density and meteorological data (wind speed and stability class). This paper will include reasonably conservative inputs, and a truncated parametric study. In lieu of the highly-conservative recommended DV value (0.1cm/s) for unmitigated/unfiltered release, GENII v2 has been used to justify estimated 95th percentile DV values. Also presented here are atmospheric dilution factors ({chi}/Q values) calculated with the MACCS2 code using the DV values form GENII v2, {chi}/Q values calculated directly with GENII v2, and a discussion of these results compare with one another. This paper will give an overview of the process of calculating DV with GENII v2 including a discussion of the sensitivity of input parameters.

Hutchins, H.

2012-04-23T23:59:59.000Z

454

Air entrainment in transient flows in closed water pipes: a two-layer approach  

E-Print Network (OSTI)

In this paper, we first construct a model for transient free surface flows that takes into account the air entrainment by a sytem of 4 partial differential equations. We derive it by taking averaged values of gas and fluid velocities on the cross surface flow in the Euler equations (incompressible for the fluid and compressible for the gas). Then, we propose a mathematical kinetic interpretation of this system to finally construct a well-balanced kinetic scheme having the properties of conserving the still water steady state and possesing an energy. Finally, numerical tests on closed uniforms water pipes are performed and discussed.

Bourdarias, Christian; Gerbi, Stphane

2009-01-01T23:59:59.000Z

455

Air Force Announces Funding for Alternative Energy Research ...  

Air Force Announces Funding for Alternative Energy Research & Development. December 16, 2013. The Air Force Research Laboratory (AFRL) has ...

456

Night air cargo operations flyover noise mitigation by a municipality  

Science Conference Proceedings (OSTI)

A 1981 Air Force Draft Environmental ImpactAnalysis (DEIA) on converting Rickenbacker Air National Guard Base (RANGB

Angelo J. Campanella

1985-01-01T23:59:59.000Z

457

Measurement of gas species, temperatures, coal burnout, and wall heat fluxes in a 200 MWe lignite-fired boiler with different overfire air damper openings  

SciTech Connect

Measurements were performed on a 200 MWe, wall-fired, lignite utility boiler. For different overfire air (OFA) damper openings, the gas temperature, gas species concentration, coal burnout, release rates of components (C, H, and N), furnace temperature, and heat flux and boiler efficiency were measured. Cold air experiments for a single burner were conducted in the laboratory. The double-swirl flow pulverized-coal burner has two ring recirculation zones starting in the secondary air region in the burner. As the secondary air flow increases, the axial velocity of air flow increases, the maxima of radial velocity, tangential velocity and turbulence intensity all increase, and the swirl intensity of air flow and the size of recirculation zones increase slightly. In the central region of the burner, as the OFA damper opening widens, the gas temperature and CO concentration increase, while the O{sub 2} concentration, NOx concentration, coal burnout, and release rates of components (C, H, and N) decrease, and coal particles ignite earlier. In the secondary air region of the burner, the O{sub 2} concentration, NOx concentration, coal burnout, and release rates of components (C, H, and N) decrease, and the gas temperature and CO concentration vary slightly. In the sidewall region, the gas temperature, O{sub 2} concentration, and NOx concentration decrease, while the CO concentration increases and the gas temperature varies slightly. The furnace temperature and heat flux in the main burning region decrease appreciably, but increase slightly in the burnout region. The NOx emission decreases from 1203.6 mg/m{sup 3} (6% O{sub 2}) for a damper opening of 0% to 511.7 mg/m{sup 3} (6% O{sub 2}) for a damper opening of 80% and the boiler efficiency decreases from 92.59 to 91.9%. 15 refs., 17 figs., 3 tabs.

Jianping Jing; Zhengqi Li; Guangkui Liu; Zhichao Chen; Chunlong Liu [Harbin Institute of Technology, Harbin (China). School of Energy Science and Engineering

2009-07-15T23:59:59.000Z

458

Ambient Operation of Li/Air Batteries  

Science Conference Proceedings (OSTI)

In this work, Li/air batteries based on nonaqueous electrolytes were investigated in ambient conditions (with an oxygen partial pressure of 0.21 atm and relative humidity of ~20%). A heat-sealable polymer membrane was used as both an oxygen-diffusion membrane and as a moisture barrier for Li/air batteries. The membrane also can minimize the evaporation of the electrolyte from the batteries. Li/air batteries with this membrane can operate in ambient conditions for more than one month with a specific energy of 362 Wh kg-1, based on the total weight of the battery including its packaging. Among various carbon sources used in this work, Li/air batteries using Ketjenblack (KB) carbon-based air electrodes exhibited the highest specific energy. However, KB-based air electrodes expanded significantly and absorbed much more electrolyte than electrodes made from other carbon sources. The weight distribution of a typical Li/air battery using the KB-based air electrode was dominated by the electrolyte (~70%). Lithium-metal anodes and KB-carbon anodes account for only 5.12% and 5.78% of the battery weight, respectively. We also found that only ~ 20% of the mesopore volume of the air electrode was occupied by reaction products after discharge. To further improve the specific energy of the Li/air batteries, the microstructure of the carbon electrode needs to be further improved to absorb much less electrolyte while still holding significant amounts of reaction products

Zhang, Jiguang; Wang, Deyu; Xu, Wu; Xiao, Jie; Williford, Ralph E.

2010-07-01T23:59:59.000Z

459

Improving air handler efficiency in houses  

SciTech Connect

Although furnaces, air conditioners and heat pumps have become significantly more efficient over the last couple of decades, residential air handlers have typical efficiencies of only 10% to 15% due to poor electric motor performance and aerodynamically poor fans and fan housings. Substantial increases in performance could be obtained through improved air handler design and construction. A prototype residential air handler intended to address these issues has recently been developed. The prototype and a standard production fan were tested in a full-scale duct system and test chamber at LBNL specifically designed for testing heating, ventilation, and air conditioning systems. The laboratory tests compared efficiency, total airflow, sensitivity to duct system flow resistance, and the effects of installation in a smaller cabinet. The test results showed that the prototype air handler had about twice the efficiency of the standard air handler (averaged over a wide range of operating conditions) and was less sensitive to duct system flow resistance changes. The performance of both air handlers was significantly reduced by reducing the clearance between the air handler and cabinet it was placed in. These test results showed that in addition to the large scope for performance improvement, air handler fans need to be tested in the cabinets they operate in.

Walker, Iain S.

2004-05-01T23:59:59.000Z

460

DOE Requires Air-Con International to Cease Sales of Inefficient Air  

NLE Websites -- All DOE Office Websites (Extended Search)

Requires Air-Con International to Cease Sales of Inefficient Requires Air-Con International to Cease Sales of Inefficient Air Conditioners and Proposes Penalties DOE Requires Air-Con International to Cease Sales of Inefficient Air Conditioners and Proposes Penalties September 21, 2010 - 6:43pm Addthis The Department has issued a Notice of Noncompliance Determination and Proposed Civil Penalty to Air-Con, International, requiring Air-Con to cease the sale of certain air-conditioning systems in the United States and proposing a civil penalty of $231,090 for sales of these products in violation of the applicable energy efficiency standards. This action reflects the Department's continued commitment to act aggressively to remove unlawful products from the market. In March, 2010, the Department issued a subpoena requiring Air-Con to

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Lithium-Air Battery: High Performance Cathodes for Lithium-Air Batteries  

SciTech Connect

BEEST Project: Researchers at Missouri S&T are developing an affordable lithium-air (Li-Air) battery that could enable an EV to travel up to 350 miles on a single charge. Todays EVs run on Li-Ion batteries, which are expensive and suffer from low energy density compared with gasoline. This new Li-Air battery could perform as well as gasoline and store 3 times more energy than current Li-Ion batteries. A Li-Air battery uses an air cathode to breathe oxygen into the battery from the surrounding air, like a human lung. The oxygen and lithium react in the battery to produce electricity. Current Li-Air batteries are limited by the rate at which they can draw oxygen from the air. The team is designing a battery using hierarchical electrode structures to enhance air breathing and effective catalysts to accelerate electricity production.

2010-08-01T23:59:59.000Z

462

Near-Surface Measurements of Quasi-Lagrangian Velocities in Open Water  

Science Conference Proceedings (OSTI)

Near-surface water velocities have been measured in the coastal zone of Lake Huron and Cape Cod Bay by tracking drifters and drogues using acoustic travel time and compass sighting techniques. The near-surface current, defined as the velocity of ...

J. H. Churchill; G. T. Csanady

1983-09-01T23:59:59.000Z

463

Effect of temperature on wave velocities in sands and sandstones with heavy hydrocarbons  

SciTech Connect

A laboratory investigation was made of the effects of temperature on wave velocities in sandstones and unconsolidated sand saturated with heavy hydrocarbons. The large decreases of the compressional and shear velocities in such sandstones and sand with increasing temperature suggest that seismic methods may be very useful in detecting heat fronts in heavy hydrocarbon reservoirs undergoing steamflooding or in-situ combustion.

Wang, Z.; Nur, A.

1988-02-01T23:59:59.000Z

464

A new method of measurement of the velocities of solar neutrinos  

E-Print Network (OSTI)

A new method of measurement of the velocities of solar electron antineutrinos is proposed. The method is based on the assumption, that if the neutrino detector having a shape of a pipe and providing a proper angular resolution, is directed onto the optical "image" of the sun, then it would detect solar neutrinos with velocities $V_{\\widetilde{\

Elmir Dermendjiev

2006-01-22T23:59:59.000Z

465

An Integrating VelocityAzimuth Process Single-Doppler Radar Wind Retrieval Method  

Science Conference Proceedings (OSTI)

Among the single-Doppler radar wind analysis methods, the velocityazimuth display (VAD), velocityazimuth process (VAP), and uniform-wind (UW) methods are widely used because of their simplicity. This paper shows that the VAD, VAP, and UW ...

Xudong Liang

2007-04-01T23:59:59.000Z

466

Modeling the Dry Deposition Velocity of Sulfur Dioxide and Sulfate in Asia  

Science Conference Proceedings (OSTI)

The dry deposition model was created to estimate SO2 and sulfate dry deposition velocities over nine land use types in Asia. The study domain is 20S50N, 39154E. Monthly averaged 1 1 dry deposition velocities are estimated for four ...

Yiwen Xu; Gregory R. Carmichael

1998-10-01T23:59:59.000Z

467

Electromagnetic plane waves with negative phase velocity in charged black strings  

SciTech Connect

We investigate the propagation regions of electromagnetic plane waves with negative phase velocity in the ergosphere of static charged black strings. For such a propagation, some conditions for negative phase velocity are established that depend on the metric components and the choice of the octant. We conclude that these conditions remain unaffected by the negative values of the cosmological constant.

Sharif, M., E-mail: msharif.math@pu.edu.pk; Manzoor, R., E-mail: rubabmanzoor9@yahoo.com [University of the Punjab, Department of Mathematics (Pakistan)

2013-02-15T23:59:59.000Z

468

Observations of Near-Surface Oceanic Velocity Strain-Rate Variability during and after Storm Events  

Science Conference Proceedings (OSTI)

During August of 1977, a series of repeated profiles of the upper ocean were made at Ocean Station Papa (145W, 50N) with a velocity/temperature microstructure profiler. A strong correlation of wind-speed variations with velocity structures in ...

R. Eward Lange

1981-09-01T23:59:59.000Z

469

Finescale Velocity-Density Characteristics and Richardson Number Statistics of the Eastern Equatorial Pacific  

Science Conference Proceedings (OSTI)

An analysis of finescale horizontal-velocity shear and density data collected along 110W longitude in the equatorial Pacific is presented. The measurements were made with the free-fall velocitydensity profiler, TOPS. Twenty-five deployments are ...

John M. Toole; Stanley P. Hayes

1984-04-01T23:59:59.000Z

470

POST-SHOCK TEMPERATURE AND FREE SURFACE VELOCITY MEASUREMENTS OF BASALT  

E-Print Network (OSTI)

POST-SHOCK TEMPERATURE AND FREE SURFACE VELOCITY MEASUREMENTS OF BASALT S. T. Stewart1 , G. B is the most common rock type on planetary surfaces. Post-shock temperature and particle velocity measurements River basalt released from a peak shock pressure of 28.9±0.2 GPa, the apparent post-shock temperature

Stewart, Sarah T.

471

Excavatability Assessment of Weathered Sedimentary Rock Mass Using Seismic Velocity Method  

SciTech Connect

Seismic refraction method is one of the most popular methods in assessing surface excavation. The main objective of the seismic data acquisition is to delineate the subsurface into velocity profiles as different velocity can be correlated to identify different materials. The physical principal used for the determination of excavatability is that seismic waves travel faster through denser material as compared to less consolidated material. In general, a lower velocity indicates material that is soft and a higher velocity indicates more difficult to be excavated. However, a few researchers have noted that seismic velocity method alone does not correlate well with the excavatability of the material. In this study, a seismic velocity method was used in Nusajaya, Johor to assess the accuracy of this seismic velocity method with excavatability of the weathered sedimentary rock mass. A direct ripping run by monitoring the actual production of ripping has been employed at later stage and compared to the ripper manufacturer's recommendation. This paper presents the findings of the seismic velocity tests in weathered sedimentary area. The reliability of using this method with the actual rippability trials is also presented.

Bin Mohamad, Edy Tonnizam; Noor, Muhazian Md; Isa, Mohamed Fauzi Bin Md.; Mazlan, Ain Naadia [Department of Geotechnics and Transportation, Faculty of Civil Engineering, Universiti Teknologi Malaysia, 81310 UTM Skudai. Johor (Malaysia); Saad, Rosli [Universiti Sains Malaysia, Penang (Malaysia)

2010-12-23T23:59:59.000Z

472

SAE Paper 2004-01-2936 Molecular Structure Effects On Laminar Burning Velocities At  

E-Print Network (OSTI)

1 SAE Paper 2004-01-2936 Molecular Structure Effects On Laminar Burning Velocities At Elevated and Engineering Copyright © 2004 Society of Automotive Engineers, Inc ABSTRACT The laminar burning velocities and pressure of 304 kPa. Data have been acquired over the stoichiometry range of 0.55 1.4. The burning

Androulakis, Ioannis (Yannis)

473

Brief paper: Global trajectory tracking control of VTOL-UAVs without linear velocity measurements  

Science Conference Proceedings (OSTI)

This paper deals with the position control of Vertical Take-Off and Landing (VTOL) Unmanned Aerial Vehicles (UAVs) without linear velocity measurements. We propose a multistage constructive procedure, exploiting the cascade property of the translational ... Keywords: Linear-velocity observer, Trajectory tracking, Unmanned Aerial Vehicles

Abdelkader Abdessameud; Abdelhamid Tayebi

2010-06-01T23:59:59.000Z

474

Reduced-dissipation remapping of velocity in staggered arbitrary Lagrangian-Eulerian methods  

Science Conference Proceedings (OSTI)

Remapping is an essential part of most Arbitrary Lagrangian-Eulerian (ALE) methods. In this paper, we focus on the part of the remapping algorithm that performs the interpolation of the fluid velocity field from the Lagrangian to the rezoned computational ... Keywords: Conservative interpolations, Flux-based remap, Staggered discretization, Velocity remap

David Bailey; Markus Berndt; Milan Kucharik; Mikhail Shashkov

2010-04-01T23:59:59.000Z

475

Results from a Velocity Transect Along the Equator from 125 to 159W  

Science Conference Proceedings (OSTI)

During MarchApril 1980, a velocity and CTD transect was made in the Pacific along the equator from 110 to 180W. The horizontal baroclinic pressure gradient was observed to be primary confined between 160 and 130W. Direct velocity profiles ...

Ants Leetmaa; Peter F. Spain

1981-07-01T23:59:59.000Z

476

Air and water cooled modulator  

DOE Patents (OSTI)

A compact high power magnetic compression apparatus and method are disclosed for delivering high voltage pulses of short duration at a high repetition rate and high peak power output which does not require the use of environmentally unacceptable fluids such as chlorofluorocarbons either as a dielectric or as a coolant, and which discharges very little waste heat into the surrounding air. A first magnetic switch has cooling channels formed therethrough to facilitate the removal of excess heat. The first magnetic switch is mounted on a printed circuit board. A pulse transformer comprised of a plurality of discrete electrically insulated and magnetically coupled units is also mounted on said printed board and is electrically coupled to the first magnetic switch. The pulse transformer also has cooling means attached thereto for removing heat from the pulse transformer. A second magnetic switch also having cooling means for removing excess heat is electrically coupled to the pulse transformer. Thus, the present invention is able to provide high voltage pulses of short duration at a high repetition rate and high peak power output without the use of environmentally unacceptable fluids and without discharging significant waste heat into the surrounding air. 9 figs.

Birx, D.L.; Arnold, P.A.; Ball, D.G.; Cook, E.G.

1995-09-05T23:59:59.000Z

477

Air and water cooled modulator  

DOE Patents (OSTI)

A compact high power magnetic compression apparatus and method for delivering high voltage pulses of short duration at a high repetition rate and high peak power output which does not require the use of environmentally unacceptable fluids such as chlorofluorocarbons either as a dielectric or as a coolant, and which discharges very little waste heat into the surrounding air. A first magnetic switch has cooling channels formed therethrough to facilitate the removal of excess heat. The first magnetic switch is mounted on a printed circuit board. A pulse transformer comprised of a plurality of discrete electrically insulated and magnetically coupled units is also mounted on said printed board and is electrically coupled to the first magnetic switch. The pulse transformer also has cooling means attached thereto for removing heat from the pulse transformer. A second magnetic switch also having cooling means for removing excess heat is electrically coupled to the pulse transformer. Thus, the present invention is able to provide high voltage pulses of short duration at a high repetition rate and high peak power output without the use of environmentally unacceptable fluids and without discharging significant waste heat into the surrounding air.

Birx, Daniel L. (Oakley, CA); Arnold, Phillip A. (Livermore, CA); Ball, Don G. (Livermore, CA); Cook, Edward G. (Livermore, CA)

1995-01-01T23:59:59.000Z

478

Air Force Enhanced Use Lease  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 1 Air Force Enhanced Use Lease Mr. Brian Brown 16 Oct. 12 I n t e g r i t y - S e r v i c e - E x c e l l e n c e 2 Agenda  Brian Brown  Enhanced Use Lease (EUL) Overview  Energy EULs  EUL Goals  David Swanson  Energy EUL Market Drivers  Current EUL Projects  Partnering with the Air Force  Contact Information I n t e g r i t y - S e r v i c e - E x c e l l e n c e 3 Overview  Authority 10 USC 2667  An EUL is a lease  By the government  Of "non-excess" property  Under the control of the government  To a public or private sector lessee  In exchange for fair market value rental payments in cash and/or in kind consideration I n t e g r i t y - S e r v i c e - E x c e l l e n c e

479

Simulation model finned water-air-coil withoutcondensation  

SciTech Connect

A simple simulation model of a finned water-to- air coil without condensation is presented. The model belongs to a collection of simulation models that allows eficient computer simulation of heating, ventilation, and air-conditioning (HVAC) systems. The main emphasis of the models is short computation time and use of input data that are known in the design process of an HVAC system. The target of the models is to describe the behavior of HVAC components in the part load operation mode, which is becoming increasingly important for energy efficient HVAC systems. The models are intended to be used for yearly energy calculation or load calculation with time steps of about 10 minutes or larger. Short-time dynamic effects, which are of interest for different aspects of control performance, are neglected. The part load behavior of the coil is expressed in terms of the nominal condition and the dimensionless variation of the heat transfer with change of mass flow and temperature on the water side and the air side. The effectiveness- NTU relations are used to parametrize the convective heat transfer at nominal conditions and to compute the part load conditions. Geometrical data for the coil are not required, The calculation of the convective heat transfer coefficients at nominal conditions is based on the ratio of the air side heat transfer coefficients multiplied by the fin eficiency and divided by the water side heat transfer coefficient. In this approach, the only geometrical information required are the cross section areas, which are needed to calculate the~uid velocities. The formulas for estimating this ratio are presented. For simplicity the model ignores condensation. The model is static and uses only explicit equations. The explicit formulation ensures short computation time and numerical stability. This allows using the model with sophisticated engineering methods such as automatic system optimization. The paper fully outlines the algorithm description and its simplifications. It is not tailored for a particular simulation program to ensure easy implementation in any simulation program.

Wetter, Michael

1999-01-01T23:59:59.000Z

480

Analysis of the AirTouch automatic vehicle location system's ability to locate moving vehicles  

E-Print Network (OSTI)

Automatic vehicle location systems are becoming more prevalent in diverse transportation applications. Their ability to locate vehicles can assist in locating emergency and public transit vehicles for better real-time dispatching as well as recovering stolen vehicles. Because many applications require traveling vehicles, this thesis focused on the AirTouch system's ability to accurately locate a moving vehicle. Recent AirTouch vehicle location system reports were compiled and analyzed to distinguish what factors tend to affect the accuracy of the readings. Based on the results of the reports, two sites were selected to minimize the external effects that could create inaccurate readings. Six speeds were selected ranging from 0 to 80 kmph (O to 50 mph) in 16 kmph (10 mph) increments. Each velocity was tested 20 times at each site. The location readings were compared to differential Global Positioning System (dGPS) readings which currently provide the most accurate location readings available for civilian use. The dGPS readings were also collected at each test site. It was discovered that one site produced more accurate readings compared to the other site. In addition, the longitude differences accounted for most of the error in the readings. Finally, more error was prevalent in the readings associated with the vehicle's direction of travel as opposed to readings perpendicular to the direction of travel. Based on the data analysis, it was impossible to conclude if velocity affected the accuracy of the AirTouch system. The results of this thesis have suggested that the AirTouch system does decrease in accuracy as the velocity increases among traveling vehicles. However, in one case, the accuracy of the stationary readings were less accurate compared to the non-stationary readings. At 80 kmph (50 mph), AirTouch had an approximate inaccuracy of 50 meters (164 feet). When the data was adjusted for human error, this approximate inaccuracy decreased to 33 meters (107 feet). For transit services, these averages are appropriate. When dispatching a transit vehicle, two-way communication between dispatcher and driver can verify the vehicle's exact location. Furthermore, when a customer needs to know where a vehicle is and when it should arrive, 33 to 50 meters (107 to 164 feet) is sufficient for the customers' needs.

Henry, Tracy Lynn

1995-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "velocity sdhv air" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

P wave velocity variations in the Coso region, California, derived from  

Open Energy Info (EERE)

P wave velocity variations in the Coso region, California, derived from P wave velocity variations in the Coso region, California, derived from local earthquake travel times Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: P wave velocity variations in the Coso region, California, derived from local earthquake travel times Details Activities (1) Areas (1) Regions (0) Abstract: Inversion of 4036 P wave travel time residuals from 429 local earthquakes using a tomographic scheme provides information about three-dimensional upper crustal velocity variations in the Indian Wells Valley-Coso region of southeastern California. The residuals are calculated relative to a Coso-specific velocity model, corrected for station elevation, weighted, and back-projected along their ray paths through models defined with layers of blocks. Slowness variations in the surface

482

Formation and evolution of interstellar filaments; Hints from velocity dispersion measurements  

E-Print Network (OSTI)

We investigate the gas velocity dispersions of a sample of filaments recently detected as part of the Herschel Gould Belt Survey in the IC5146, Aquila, and Polaris interstellar clouds. To measure these velocity dispersions, we use 13CO, C18O, and N2H+ line observations obtained with the IRAM 30m telescope. Correlating our velocity dispersion measurements with the filament column densities derived from Herschel data, we show that interstellar filaments can be divided into two regimes: thermally subcritical filaments, which have transonic velocity dispersions (c_s ~dispersions scaling roughly as the square root of column density (\\sigma_tot ~ \\Sigma^0.5), and are self-gravitating. The higher velocity dispersions of supercritical filaments may not directly arise from supersonic interstellar turbulence but may be driven by gravitational contraction/accretion...

Arzoumanian, Doris; Peretto, Nicolas; Konyves, Vera

2013-01-01T23:59:59.000Z