Powered by Deep Web Technologies
Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Effects of Woody Vegetation Removal on Soil Water Dynamics in a South Texas Shrubland  

E-Print Network [OSTI]

removal on various soil textures we studied changes in soil water, rooting depth, and the role of water redistribution by woody vegetation. Woody vegetation was removed using common methods of cut-stump and roller chop across three soil types. Soil water...

Mattox, April Marie

2013-07-30T23:59:59.000Z

2

Specialty Vegetables in Texas.  

E-Print Network [OSTI]

chayote squash - Creole cooks call it mirliton, South Americans call it mango squash and Floridians call it a vegetable pear. These are all the same vegetable but with many names! Amaranths (Chinese Spinach) Description. Amaranths are green, leafy... wash flowers thoroughly and make certain all chemical or organic pesticide has been removed. Give them a gentle bath in salt water and then dip the petals in ice water to perk them up. Drain on paper towels. For later marketing, petals and whole...

Longbrake, Thomas D.; Baker, Marvin L.; Cotner, Sam; Parsons, Jerry; Roberts, Roland; Stein, Larry

1988-01-01T23:59:59.000Z

3

Ground Water Ground Sky Sky Water Vegetation Ground Vegetation Water  

E-Print Network [OSTI]

Bear Snow Vegetation RhinoWater Vegetation Ground Water Ground Sky Sky Rhino Water Vegetation Ground Vegetation Water Rhino Water Vegetation Ground Rhino Water Rhino Water Ground Ground Vegetation Water Rhino Vegetation Rhino Vegetation Ground Rhino Vegetation Ground Sky Rhino Vegetation Ground Sky

Chen, Tsuhan

4

Hydrodynamics of vegetated channels  

E-Print Network [OSTI]

This paper highlights some recent trends in vegetation hydrodynamics, focusing on conditions within channels and spanning spatial scales from individual blades, to canopies or vegetation patches, to the channel reach. At ...

Nepf, Heidi

5

CX-007140: Categorical Exclusion Determination | Department of...  

Broader source: Energy.gov (indexed) [DOE]

Determination Vegetation Removal and Access Road Maintenance along the existing Electrical District 2-Saguaro 2 115-kV transmission line CX(s) Applied: B1.3 Date: 03212011...

6

Categorical Exclusion Determinations: Western Area PowerAdministratio...  

Broader source: Energy.gov (indexed) [DOE]

and Vegetation ControlRemoval CX(s) Applied: B1.3 Date: 03292010 Location(s): Sioux City, Iowa Office(s): Western Area Power Administration-Upper Great Plains Region March...

7

Fresh Vegetables: Getting the Most Nutrition for Your Money  

E-Print Network [OSTI]

and quality. Visit local farmer?s markets and roadside stands. Grocery stores aren?t the only place to buy fresh vegetables. Be Safe! P oor storage and preparation of vegeta- bles can cost you money if the vegeta- bles go to waste or cause a foodborne... carefully. Bruises and other blemishes speed up deterioration and allow bacteria to enter the produce. Use clean, cool, running water to wash the vegetables. Hard vegetables like potatoes and carrots should be cleaned with a vegetable brush to remove any...

Anding, Jenna

2000-05-05T23:59:59.000Z

8

Performance of vegetated roadsides in removing stormwater pollutants  

E-Print Network [OSTI]

sections in two Texas cities: Austin and College Station. Three sites in each city were examined in this study over a 14-month monitoring period. No significant difference between the edges of pavement pollutant concentrations were observed at any...

Rammohan, Pavitra

2006-08-16T23:59:59.000Z

9

Vegetables: Selection, Care, Cooking.  

E-Print Network [OSTI]

and blemishes and decay. For the least waste in paring, select potatoes that are regular in shape and have shallow eyes. Avoid potatoes that show green 1 color on some part of the surface; the green portions taste bitter. One pound of fresh po- , tatoes... aging. daily food guide for Texans, three kinds of Other vegetables include all those that are vegetables-green or yellow, other vegetables not green or yellow, and supply other needed and Irish or sweet potatoes are good nutrition vitamins...

Reasonover, Frances; Mason, Louise; Tribble, Marie; Cox, Maeona

1958-01-01T23:59:59.000Z

10

Vegetable Gardening in Containers  

E-Print Network [OSTI]

This 7 page publications explains how to grow vegetables in containers when insufficient space or unsutable soil conditions make a traditional garden difficult to achieve. Topics include: container materials, crop selection, growing media, seeding...

Masabni, Joseph; Cotner, Sam

2009-02-25T23:59:59.000Z

11

Chicken Noodle Soup 3 T. canola or vegetable oil  

E-Print Network [OSTI]

Chicken Noodle Soup 3 T. canola or vegetable oil 3# chicken bone-in (thigh meat or legs the skins and ends for the stock. Cut the end off the celery head and reserve for stock. Cut both onions in half and remove skin of onion and reserve for stock. Take 1 carrot, 1 stalk of celery and 1 onion

Liu, Taosheng

12

Native Vegetation Planting Guidelines  

E-Print Network [OSTI]

1 Native Vegetation Planting Guidelines Based on Sustainability Goals for the Macquarie Campus #12.................................................................................................................................10 4.2.5 Shale-Sandstone soil transition...................................................................................................................................11 #12;3 1. Purpose This document provides a guideline for specific grounds management procedures

Wang, Yan

13

Vegetable Gardening in Containers.  

E-Print Network [OSTI]

are indicated in Table 1. * Growing Media Synthetic "soils" are best suited for vegetable container gardening. These mixes may be composed of sawdust, wood chips, peat moss, perlite, ver miculite or almost any other type of media. Regardless of what... "soils" are available from gar den centers, or one can be pre pared by mixing horticultu ral grade vermiculite, peat moss, limestone, superphosphate, and garden fertilizer. To 1 bushel each of vermiculite and peat moss, add 10 tablespoons...

Cotner, Sam

1981-01-01T23:59:59.000Z

14

Turbomachinery debris remover  

DOE Patents [OSTI]

An apparatus for removing debris from a turbomachine. The apparatus includes housing and remotely operable viewing and grappling mechanisms for the purpose of locating and removing debris lodged between adjacent blades in a turbomachine.

Krawiec, Donald F. (Pittsburgh, PA); Kraf, Robert J. (North Huntingdon, PA); Houser, Robert J. (Monroeville, PA)

1988-01-01T23:59:59.000Z

15

Chapter 17 Vegetation  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed New Substation SitesStanding FriedelIron-Sulfur3-1 November 2012 Words in17-1

16

N A Vegetation  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment SurfacesResource ProgramModificationEnzyme-FunctionalizedCirculatoryo r t h F o-N A

17

Vegetation | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address: 160 East 300 South Place: Salt Lake City, Utah Zip:ScaleVegetation Jump to: navigation,

18

How to deal with radiologically contaminated vegetation  

SciTech Connect (OSTI)

This report describes the findings from a literature review conducted as part of a Department of Energy, Office of Technology Development Biomass Remediation Task. The principal objective of this project is to develop a process or group of processes to treat radiologically contaminated vegetation in a manner that minimizes handling, processing, and treatment costs. Contaminated, woody vegetation growing on waste sites at SRS poses a problem to waste site closure technologies that are being considered for these sites. It is feared that large sections of woody vegetation (logs) can not be buried in waste sites where isolation of waste is accomplished by capping the site. Logs or large piles of woody debris have the potential of decaying and leaving voids under the cap. This could lead to cap failure and entrance of water into the waste. Large solid objects could also interfere with treatments like in situ mixing of soil with grout or other materials to encapsulate the contaminated sediments and soils in the waste sites. Optimal disposal of the wood includes considerations of volume reduction, treatment of the radioactive residue resulting from volume reduction, or confinement without volume reduction. Volume reduction consists primarily of removing the carbon, oxygen, and hydrogen in the wood, leaving an ash that would contain most of the contamination. The only contaminant that would be released by volume reduction would by small amounts of the radioactive isotope of hydrogen, tritium. The following sections will describe the waste sites at SRS which contain contaminated vegetation and are potential candidates for the technology developed under this proposal. The description will provide a context for the magnitude of the problem and the logistics of the alternative solutions that are evaluated later in the review. 76 refs.

Wilde, E.W.; Murphy, C.E.; Lamar, R.T.; Larson, M.J.

1996-12-31T23:59:59.000Z

19

RAPID SEPARATION OF ACTINIDES AND RADIOSTRONTIUM IN VEGETATION SAMPLES  

SciTech Connect (OSTI)

A new rapid method for the determination of actinides and radiostrontium in vegetation samples has been developed at the Savannah River Site Environmental Lab (Aiken, SC, USA) that can be used in emergency response situations or for routine analysis. The actinides in vegetation method utilizes a rapid sodium hydroxide fusion method, a lanthanum fluoride matrix removal step, and a streamlined column separation process with stacked TEVA, TRU and DGA Resin cartridges. Lanthanum was separated rapidly and effectively from Am and Cm on DGA Resin. Alpha emitters are prepared using rare earth microprecipitation for counting by alpha spectrometry. The purified {sup 90}Sr fractions are mounted directly on planchets and counted by gas flow proportional counting. The method showed high chemical recoveries and effective removal of interferences. The actinide and {sup 90}Sr in vegetation sample analysis can be performed in less than 8 h with excellent quality for emergency samples. The rapid fusion technique is a rugged sample digestion method that ensures that any refractory actinide particles or vegetation residue after furnace heating is effectively digested.

Maxwell, S.

2010-06-01T23:59:59.000Z

20

Continuous sulfur removal process  

DOE Patents [OSTI]

A continuous process for the removal of hydrogen sulfide from a gas stream using a membrane comprising a metal oxide deposited on a porous support is disclosed. 4 figures.

Jalan, V.; Ryu, J.

1994-04-26T23:59:59.000Z

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Reactor for removing ammonia  

DOE Patents [OSTI]

Disclosed is a device for removing trace amounts of ammonia from a stream of gas, particularly hydrogen gas, prepared by a reformation apparatus. The apparatus is used to prevent PEM "poisoning" in a fuel cell receiving the incoming hydrogen stream.

Luo, Weifang (Livermore, CA); Stewart, Kenneth D. (Valley Springs, CA)

2009-11-17T23:59:59.000Z

22

International bibliography of vegetation maps  

E-Print Network [OSTI]

:100,000,000], in Voss, John, "Preliminary report of the paleo-ecology of a Wisconsin and an Illinois bog." Trans. Illinois State Acad. Sci., vol. 24, p. 136.) 1887 "VEGETATION REGIONS ACCORDING TO OSCAR DRUDE" black and white [1:56,300,0001 LEGEND 1. Tundra 2... survey of North America." In Engler, A., and Oscar Drude (eds.), Die Vegetation der Erde. Leipzig, Wilhelm Engelmann, vol. 13, inserted at back. [ 1911 ] "NORTH AMERICA VEGETATION" black and white [ 1 -.34,400,000] LEGEND 1. Tropical forest 5...

Ku?chler, A. W. (August William)

1965-01-01T23:59:59.000Z

23

Selecting Fresh Fruits and Vegetables  

E-Print Network [OSTI]

time. Selecting Fresh Fruits and Vegetables Amanda Scott* E-197 9/08 This publication was sponsored by a grant from the Initiative for Future Agriculture Food Systems, a program of the Cooperative State Research, Education, and Extension Service, which...

Scott, Amanda

2008-09-05T23:59:59.000Z

24

Longitudinal dispersion in vegetated flow  

E-Print Network [OSTI]

Vegetation is ubiquitous in rivers, estuaries and wetlands, strongly influencing both water conveyance and mass transport. The plant canopy affects both mean and turbulent flow structure, and thus both advection and ...

Murphy, Enda

2006-01-01T23:59:59.000Z

25

Texas Home Vegetable Gardening Guide  

E-Print Network [OSTI]

With this manual, home gardeners are sure to be successful growing vegetables. It includes information on garden planning, crop selection, soil preparation, fertilization, planting techniques, watering, pest control and harvesting. Tables show...

Masabni, Joseph

2009-02-24T23:59:59.000Z

26

Supplement Analysis for the Transmission System Vegetation Management Program FEIS (DOE/EIS-0285/SA-15)  

SciTech Connect (OSTI)

BPA proposes to clear unwanted vegetation in the rights-of-ways and around tower structures that may impede the operation and maintenance of the subject transmission lines. Work also includes clearing of a small (<1/4 mile) section of access road. All work will be in accordance with the National Electrical Safety Code and BPA standards. See Section 1.1 of the attached checklist for detailed information on each section of the referenced transmission lines. BPA will conduct the vegetation control with the goal of removing tall-growing vegetation that is currently or will soon be a hazard to the transmission lines and where possible to promote low-growing plant communities in the right-of-way. This project meets the standards and guidelines for the Transmission System Vegetation Management Program Final Environmental Impact Statement (FEIS) and Record of Decision (ROD). The vegetation needing control is mainly Douglas Fir, Alder, and blackberries as indicated in Section 1.2 of the attached checklist. The work involved in the ROW includes: clearing tall growing vegetation that is currently or will soon pose a hazard to the lines; treating the associated stumps and re-sprouts with herbicide to ensure that the roots are killed preventing new sprouts; and selectively eliminating tall growing vegetation before it reaches a height or density to begin competing with low-growing vegetation. All work will take place in existing rights-of-ways and around transmission structures. All work will be accomplished by selective vegetation control methods to assure that there is little potential harm to non-target vegetation and to low-growing plants. The work will provide system reliability and fire protection. Also, all off right-of-way trees that are potentially unstable and will fall within a minimum distance or into the zone where the conductors swing will be removed. Access roads will be treated using mowing and herbicide applications. The work will provide system reliability. The subject transmission lines range from 115kV to 230kV and are made up of accompanying access roads, steel and wooden transmission line structures and associated switching platforms. The minimum clearance ranges from 21 feet for 115kV lines to 23 feet for 230kV lines. ROW easement widths vary along the length of the project. Vegetation control for this project is designed to provide a 3 year maintenance free interval. In summary, the overall vegetation management scheme will be to selectively remove tall growing vegetation then apply selective herbicide treatment using cut stump applications.

N /A

2001-06-19T23:59:59.000Z

27

Arsenic removal from water  

DOE Patents [OSTI]

Methods for removing arsenic from water by addition of inexpensive and commonly available magnesium oxide, magnesium hydroxide, calcium oxide, or calcium hydroxide to the water. The hydroxide has a strong chemical affinity for arsenic and rapidly adsorbs arsenic, even in the presence of carbonate in the water. Simple and commercially available mechanical methods for removal of magnesium hydroxide particles with adsorbed arsenic from drinking water can be used, including filtration, dissolved air flotation, vortex separation, or centrifugal separation. A method for continuous removal of arsenic from water is provided. Also provided is a method for concentrating arsenic in a water sample to facilitate quantification of arsenic, by means of magnesium or calcium hydroxide adsorption.

Moore, Robert C. (Edgewood, NM); Anderson, D. Richard (Albuquerque, NM)

2007-07-24T23:59:59.000Z

28

Removable feedwater sparger assembly  

DOE Patents [OSTI]

A removable feedwater sparger assembly includes a sparger having an inlet pipe disposed in flow communication with the outlet end of a supply pipe. A tubular coupling includes an annular band fixedly joined to the sparger inlet pipe and a plurality of fingers extending from the band which are removably joined to a retention flange extending from the supply pipe for maintaining the sparger inlet pipe in flow communication with the supply pipe. The fingers are elastically deflectable for allowing engagement of the sparger inlet pipe with the supply pipe and for disengagement therewith.

Challberg, Roy C. (Livermore, CA)

1994-01-01T23:59:59.000Z

29

Drum lid removal tool  

DOE Patents [OSTI]

A tool for removing the lid of a metal drum wherein the lid is clamped over the drum rim without protruding edges, the tool having an elongated handle with a blade carried by an angularly positioned holder affixed to the midsection of the handle, the blade being of selected width to slice between lid lip and the drum rim and, when the blade is so positioned, upward motion of the blade handle will cause the blade to pry the lip from the rim and allow the lid to be removed.

Pella, Bernard M. (Martinez, GA); Smith, Philip D. (North Augusta, SC)

2010-08-24T23:59:59.000Z

30

Removable feedwater sparger assembly  

DOE Patents [OSTI]

A removable feedwater sparger assembly includes a sparger having an inlet pipe disposed in flow communication with the outlet end of a supply pipe. A tubular coupling includes an annular band fixedly joined to the sparger inlet pipe and a plurality of fingers extending from the band which are removably joined to a retention flange extending from the supply pipe for maintaining the sparger inlet pipe in flow communication with the supply pipe. The fingers are elastically deflectable for allowing engagement of the sparger inlet pipe with the supply pipe and for disengagement therewith. 8 figs.

Challberg, R.C.

1994-10-04T23:59:59.000Z

31

Modeling of the interactions between forest vegetation, disturbances, and sediment yields  

E-Print Network [OSTI]

Modeling of the interactions between forest vegetation, disturbances, and sediment yields Erkan on the frequency and magnitude of sediment delivery from a small watershed ($3.9 km2 ) in the Idaho batholith weathering and the divergence of diffusive sediment transport on hillslopes. Soil removal is due to episodic

Tarboton, David

32

Pneumatic soil removal tool  

DOE Patents [OSTI]

A soil removal tool is provided for removing radioactive soil, rock and other debris from the bottom of an excavation, while permitting the operator to be located outside of a containment for that excavation. The tool includes a fixed jaw, secured to one end of an elongate pipe, which cooperates with a movable jaw pivotably mounted on the pipe. Movement of the movable jaw is controlled by a pneumatic cylinder mounted on the pipe. The actuator rod of the pneumatic cylinder is connected to a collar which is slidably mounted on the pipe and forms part of the pivotable mounting assembly for the movable jaw. Air is supplied to the pneumatic cylinder through a handle connected to the pipe, under the control of an actuator valve mounted on the handle, to provide movement of the movable jaw. 3 figs.

Neuhaus, J.E.

1992-10-13T23:59:59.000Z

33

Pneumatic soil removal tool  

DOE Patents [OSTI]

A soil removal tool is provided for removing radioactive soil, rock and other debris from the bottom of an excavation, while permitting the operator to be located outside of a containment for that excavation. The tool includes a fixed jaw, secured to one end of an elongate pipe, which cooperates with a movable jaw pivotably mounted on the pipe. Movement of the movable jaw is controlled by a pneumatic cylinder mounted on the pipe. The actuator rod of the pneumatic cylinder is connected to a collar which is slidably mounted on the pipe and forms part of the pivotable mounting assembly for the movable jaw. Air is supplied to the pneumatic cylinder through a handle connected to the pipe, under the control of an actuator valve mounted on the handle, to provide movement of the movable jaw.

Neuhaus, John E. (Newport News, VA)

1992-01-01T23:59:59.000Z

34

KKG Group Paraffin Removal  

SciTech Connect (OSTI)

The Rocky Mountain Oilfield Testing Center (RMOTC) has recently completed a test of a paraffin removal system developed by the KKG Group utilizing the technology of two Russian scientists, Gennady Katzyn and Boris Koggi. The system consisting of chemical ''sticks'' that generate heat in-situ to melt the paraffin deposits in oilfield tubing. The melted paraffin is then brought to the surface utilizing the naturally flowing energy of the well.

Schulte, Ralph

2001-12-01T23:59:59.000Z

35

Vegetation Change Analysis User's Manual  

SciTech Connect (OSTI)

Approximately 70 percent of all U.S. military training lands are located in arid and semi-arid areas. Training activities in such areas frequently adversely affect vegetation, damaging plants and reducing the resilience of vegetation to recover once disturbed. Fugitive dust resulting from a loss of vegetation creates additional problems for human health, increasing accidents due to decreased visibility, and increasing maintenance costs for roads, vehicles, and equipment. Diagnostic techniques are needed to identify thresholds of sustainable military use. A cooperative effort among U.S. Department of Energy, U.S. Department of Defense, and selected university scientists was undertaken to focus on developing new techniques for monitoring and mitigating military impacts in arid lands. This manual focuses on the development of new monitoring techniques that have been implemented at Fort Irwin, California. New mitigation techniques are described in a separate companion manual. This User's Manual is designed to address diagnostic capabilities needed to distinguish between various degrees of sustainable and nonsustainable impacts due to military training and testing and habitat-disturbing activities in desert ecosystems. Techniques described here focus on the use of high-resolution imagery and the application of image-processing techniques developed primarily for medical research. A discussion is provided about the measurement of plant biomass and shrub canopy cover in arid. lands using conventional methods. Both semiquantitative methods and quantitative methods are discussed and reference to current literature is provided. A background about the use of digital imagery to measure vegetation is presented.

D. J. Hansen; W. K. Ostler

2002-10-01T23:59:59.000Z

36

Environmental Effects of Woody Vegetation  

E-Print Network [OSTI]

. In rural loca- tions, woody vegetation provides for man's protection and preservation. Farm windbreaks in improv- ing human comfort by shielding people from direct solar radiation. What happens to the solar but significant amount is used for heating tree parts. The portion of solar radiation used in photosynthesis (food

Koford, Rolf R.

37

Vegetable Crops Hotline index 2005 MANAGEMENT TIPS  

E-Print Network [OSTI]

Labeled for Row Middle Use in Vegetable Crops 446 Kudzu Turning Over New Leaves in Indiana Counties 447

Ginzel, Matthew

38

Straight Vegetable Oil as a Diesel Fuel?  

SciTech Connect (OSTI)

Two-page fact sheet discussing the pitfalls of using straight vegetable oil (SVO) as a transportation fuel.

Not Available

2006-04-01T23:59:59.000Z

39

Fruit and Vegetable Consumption by Low-Income Americans  

E-Print Network [OSTI]

ML, Schillo BA. 5 A Day fruit and vegetable interventionof perceived barriers to fruit and vegetable consumptionKA, Potter JD. Vegetables, fruit, and cancer prevention: a

Sisson, Aimee

2002-01-01T23:59:59.000Z

40

Vegetation  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear SecurityTensile Strain Switched Ferromagnetism inS-4500IIVasudha Patri Mechanical Engineer Telephoneo 250 o 250 G-2.6

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Vegetation  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear SecurityTensile Strain Switched Ferromagnetism inS-4500IIVasudha Patri Mechanical Engineer Telephoneo 250 o 250

42

Vegetation  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear SecurityTensile Strain Switched Ferromagnetism inS-4500IIVasudha Patri Mechanical Engineer Telephoneo 250 o 250/::vI

43

Geothermal hydrogen sulfide removal  

SciTech Connect (OSTI)

UOP Sulfox technology successfully removed 500 ppM hydrogen sulfide from simulated mixed phase geothermal waters. The Sulfox process involves air oxidation of hydrogen sulfide using a fixed catalyst bed. The catalyst activity remained stable throughout the life of the program. The product stream composition was selected by controlling pH; low pH favored elemental sulfur, while high pH favored water soluble sulfate and thiosulfate. Operation with liquid water present assured full catalytic activity. Dissolved salts reduced catalyst activity somewhat. Application of Sulfox technology to geothermal waters resulted in a straightforward process. There were no requirements for auxiliary processes such as a chemical plant. Application of the process to various types of geothermal waters is discussed and plans for a field test pilot plant and a schedule for commercialization are outlined.

Urban, P.

1981-04-01T23:59:59.000Z

44

Sky Vegetables | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia:FAQ < RAPID Jump to:Seadov Pty Ltd Jump to: navigation,PvtSouth Dakota) Jump to:Oklahoma:Vegetables Jump to:

45

Removing Arsenic from Drinking Water  

ScienceCinema (OSTI)

See how INL scientists are using nanotechnology to remove arsenic from drinking water. For more INL research, visit http://www.facebook.com/idahonationallaboratory

None

2013-05-28T23:59:59.000Z

46

Ecophysiology of forest and savanna vegetation  

E-Print Network [OSTI]

Lowland vegetation of tropical South America—An overview, instate for tropical South America, Geophys. Res. Lett. , 30(dry seasonal forests of South America, Ann. Mo. Bot. Gard. ,

Lloyd, J.; Goulden, M. L.; Ometto, J. P.; Patino, S.; Fyllas, N. M.; Quesada, C. A.

2013-01-01T23:59:59.000Z

47

Monte Carlo simulation model for electromagnetic scattering from vegetation and inversion of vegetation parameters  

E-Print Network [OSTI]

In this thesis research, a coherent scattering model for microwave remote sensing of vegetation canopy is developed on the basis of Monte Carlo simulations. An accurate model of vegetation structure is essential for the ...

Wang, Li-Fang, Ph. D. Massachusetts Institute of Technology

2007-01-01T23:59:59.000Z

48

Sandhills Vegetation Will heat from the pipeline affect the growth of vegetation?  

E-Print Network [OSTI]

1 Sandhills Vegetation Will heat from the pipeline affect the growth of vegetation? What we know. Will the Sandhills vegetation grow back after the pipeline is constructed? What we know ­ response by Professor Jerry issues, revegetation problems on the pipeline will be at discreet locations. If surrounding pastures

Nebraska-Lincoln, University of

49

Fruit and Vegetable Safety Challenge Game Directions  

E-Print Network [OSTI]

1 Fruit and Vegetable Safety Challenge Game Directions Equipment needed: 1. Computer, projector (fruits, vegetables, and meat) 6. Cleaning solutions (bleach, soap, water) 7. Stop watch 8. Team prizes How to Start: This game can be used with the "A Healthy Harvest: Safe Handling of Fresh Fruits

50

Guide for Developing Integrated Aquatic Vegetation Management  

E-Print Network [OSTI]

Guide for Developing Integrated Aquatic Vegetation Management Plans in Oregon Maribeth V. Gibbons is an integrated aquatic vegetation management plan? When is an IAVMP required? Part II: Developing a Plan Chapter and Reservoirs · Portland State University · Portland OR 97207 #12;Acknowledgements This manual benefited

51

HYDROPONIC VEGETABLE GARDENING Marcy Stanton, Master Gardener  

E-Print Network [OSTI]

and a water source. Lighting: A simple 2-bulb 4-foot fluorescent fixture with standard COOL WHITE bulbs is adequate for most leafy vegetables. Do not buy any of the fancy fluorescent grow bulbs; you are wasting your money on these expensive bulbs. When we set up a fluorescent light system to grow vegetables, what

New Hampshire, University of

52

Fish and Vegetables in Foil Ingredients  

E-Print Network [OSTI]

Fish and Vegetables in Foil Ingredients: 1 1/2 pounds fresh or frozen fish fillets or steaks 4 sodium) Directions 1. Rinse fish under cold water and pat dry. Place 4 individual portions of fish on 4 pieces of foil large enough to completely wrap around the fish and vegetables. 2. Diagonally slice

Liskiewicz, Maciej

53

International Workshop Responses of Vegetation and Human  

E-Print Network [OSTI]

of southern Russia and climatic changes" 15.00 ­ Dr. A. Skorobogatov (Voronezh University, Russia). "TheInternational Workshop Responses of Vegetation and Human Society to Climatic Changes in Ukraine- Ukrainian team started to investigate Holocene climate changes and the resulting vegetation and human

Bern, Universität

54

Interaction between flow, transport and vegetation spatial structure  

E-Print Network [OSTI]

This paper summarizes recent advances in vegetation hydrodynamics and uses the new concepts to explore not only how vegetation impacts flow and transport, but also how flow feedbacks can influence vegetation spatial ...

Luhar, Mitul

55

Reliability Based Vegetation Management Through Intelligent System Monitoring  

E-Print Network [OSTI]

Reliability Based Vegetation Management Through Intelligent System Monitoring Final Project Report Research Center since 1996 PSERC #12;Power Systems Engineering Research Center Reliability Based Vegetation project titled "Reliability Based Vegetation Maintenance Through Intelligent System Monitoring (T-27)." We

56

CONNECTICUT VEGETABLE & SMALL FRUIT GROWERS' Thursday, January 15, 2015  

E-Print Network [OSTI]

CONNECTICUT VEGETABLE & SMALL FRUIT GROWERS' CONFERENCE Thursday, January 15, 2015 Maneeley. Connecticut Vegetable & Small Fruit Growers' Conference (We need folks to pre-register so Maneeley's has:______________________________________ ---- Town:______________ State:_____ Zip:____________ ---- Check off: Vegetable grower ___ Fruit grower

Alpay, S. Pamir

57

Special study on vegetative covers. [UMTRA Project  

SciTech Connect (OSTI)

This report describes the findings of a special study on the use of vegetative covers to stabilize tailings piles for the Uranium Mill Tailings Remedial Action (UMTRA) Project. The principal rationale for using plants would be to establish a dynamic system for controlling water balance. Specifically, vegetation would be used to intercept and transpire precipitation to the atmosphere, rather than allowing water to drain into the tailings and mobilize contaminants. This would facilitate compliance with groundwater standards proposed for the UMTRA Project by the Environmental Protection Agency. The goals of the study were to evaluate the feasibility of using vegetative covers on UMTRA Project piles, define the advantages and disadvantages of vegetative covers, and develop general guidelines for their use when such use seems reasonable. The principal method for the study was to analyze and apply to the UMTRA Project the results of research programs on vegetative covers at other US Department of Energy (DOE) waste management facilities. The study also relied upon observations made of existing stabilized piles at UMTRA Project sites where natural vegetation is growing on the rock-covered surfaces. Water balance and erosion models were also used to quantify the long-term performance of vegetative covers planned for the topslopes of stabilized piles at Grand Junction and Durango, Colorado, two UMTRA Project sites where the decision was made during the course of this special study to use vegetative covers. Elements in the design and construction of the vegetative covers at these two sites are discussed in the report, with explanations of the differing features that reflect differing environmental conditions. 28 refs., 18 figs., 9 tabs.

Not Available

1988-11-01T23:59:59.000Z

58

Vegetative covers: Special study. [Final report  

SciTech Connect (OSTI)

This report describes the findings of a special study on the use of vegetative covers to stabilize tailings piles for the Uranium Mill Tailings Remedial Action (UMTRA) Project. The principal rationale for using plants would be to establish a dynamic system for controlling water balance. Specifically, vegetation would be used to intercept and transpire precipitation to the atmosphere, rather than allowing water to drain into the tailings and mobilize contaminants. This would facilitate compliance with groundwater standards proposed for the UMTRA Project by the Environmental Protection Agency. The goals of the study were to (1) evaluate the feasibility of using vegetative covers on UMTRA Project piles, (2) define the advantages and disadvantages of vegetative covers, and (3) develop general guidelines for their use when such use seems reasonable. The principal method for the study was to analyze and apply to the UMTRA Project the results of research programs on vegetative covers at other US Department of Energy (DOE) waste management facilities. The study also relied upon observations made of existing stabilized piles at UMTRA Project sites (Shiprock, New Mexico; Burrell, Pennsylvania; and Clive, Utah) where natural vegetation is growing on the rock-covered surfaces. Water balance and erosion models were also used to quantify the long-term performance of vegetative covers planned for the topslopes of stabilized piles at Grand Junction and Durango, Colorado, two UMTRA Project sites where the decision was made during the course of this special study to use vegetative covers. Elements in the design and construction of the vegetative covers at these two sites are discussed in the report, with explanations of the differing features that reflect differing environmental conditions.

Not Available

1988-11-01T23:59:59.000Z

59

High removal rate laser-based coating removal system  

DOE Patents [OSTI]

A compact laser system that removes surface coatings (such as paint, dirt, etc.) at a removal rate as high as 1000 ft.sup.2 /hr or more without damaging the surface. A high repetition rate laser with multiple amplification passes propagating through at least one optical amplifier is used, along with a delivery system consisting of a telescoping and articulating tube which also contains an evacuation system for simultaneously sweeping up the debris produced in the process. The amplified beam can be converted to an output beam by passively switching the polarization of at least one amplified beam. The system also has a personal safety system which protects against accidental exposures.

Matthews, Dennis L. (Moss Beach, CA); Celliers, Peter M. (Berkeley, CA); Hackel, Lloyd (Livermore, CA); Da Silva, Luiz B. (Danville, CA); Dane, C. Brent (Livermore, CA); Mrowka, Stanley (Richmond, CA)

1999-11-16T23:59:59.000Z

60

Heavy Water Test Reactor Dome Removal  

SciTech Connect (OSTI)

A high speed look at the removal of the Heavy Water Test Reactor Dome Removal. A project sponsored by the Recovery Act on the Savannah River Site.

None

2011-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Supplement Analysis for the Transmission System Vegetation Management...  

Broader source: Energy.gov (indexed) [DOE]

and Record of Decision (ROD). Planning Steps 1. Identify facility and the vegetation management need. The work involved will be to clear tall growing vegetation that is...

62

Large Component Removal/Disposal  

SciTech Connect (OSTI)

This paper describes the removal and disposal of the large components from Maine Yankee Atomic Power Plant. The large components discussed include the three steam generators, pressurizer, and reactor pressure vessel. Two separate Exemption Requests, which included radiological characterizations, shielding evaluations, structural evaluations and transportation plans, were prepared and issued to the DOT for approval to ship these components; the first was for the three steam generators and one pressurizer, the second was for the reactor pressure vessel. Both Exemption Requests were submitted to the DOT in November 1999. The DOT approved the Exemption Requests in May and July of 2000, respectively. The steam generators and pressurizer have been removed from Maine Yankee and shipped to the processing facility. They were removed from Maine Yankee's Containment Building, loaded onto specially designed skid assemblies, transported onto two separate barges, tied down to the barges, th en shipped 2750 miles to Memphis, Tennessee for processing. The Reactor Pressure Vessel Removal Project is currently under way and scheduled to be completed by Fall of 2002. The planning, preparation and removal of these large components has required extensive efforts in planning and implementation on the part of all parties involved.

Wheeler, D. M.

2002-02-27T23:59:59.000Z

63

The limited growth of vegetated shear layers  

E-Print Network [OSTI]

In contrast to free shear layers, which grow continuously downstream, shear layers generated by submerged vegetation grow only to a finite thickness. Because these shear layers are characterized by coherent vortex structures ...

Ghisalberti, M.

64

Membrane degumming of crude vegetable oil  

E-Print Network [OSTI]

Crude vegetable oils contain various minor substances like phospholipids, coloring pigments, and free fatty acids (FFA) that may affect quality of the oil. Reduction of energy costs and waste disposal are major concerns for many oil refiners who...

Lin, Lan

1997-01-01T23:59:59.000Z

65

Bonneville - Hood River Vegetation Management Environmental Assessment  

SciTech Connect (OSTI)

To maintain the reliability of its electrical system, BPA, in cooperation with the U.S. Forest Service, needs to expand the range of vegetation management options used to clear unwanted vegetation on about 20 miles of BPA transmission line right-of-way between Bonneville Dam and Hood River; Oregon, within the Columbia Gorge National Scenic Area (NSA). We propose to continue controlling undesirable vegetation using a program of Integrated Vegetation Management (IVM) which includes manual, biological and chemical treatment methods. BPA has prepared an Environmental Assessment (EA) (DOE/EA-1257) evaluating the proposed project. Based on the analysis in the EA, BPA has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment, within the meaning of the National Environmental Policy Act (NEPA) of 1969. Therefore, the preparation of an Environmental Impact Statement (EIS) is not required and BPA is issuing this FONSI.

N /A

1998-08-01T23:59:59.000Z

66

CLIMATE CHANGE IMPACTS ON CALIFORNIA VEGETATION  

E-Print Network [OSTI]

CLIMATE CHANGE IMPACTS ON CALIFORNIA VEGETATION: PHYSIOLOGY, LIFE HISTORY, AND ECOSYSTEM CHANGE A White Paper from the California Energy Commission's California Climate Change Center of the uncertainties with climate change effects on terrestrial ecosystems is understanding where transitions

67

Safe Storage of Fresh Fruits and Vegetables  

E-Print Network [OSTI]

Proper storage of fresh fruits and vegetables can help consumers avoid foodborne illness. This publication explains how to safely store apples, bananas, berries, beets, broccoli, carrots, corn, grapes, herbs, lettuce and greens, melons, nectarines...

Scott, Amanda

2008-09-05T23:59:59.000Z

68

Nonlinear Characteristics of Wave Propagation over Vegetation  

E-Print Network [OSTI]

The attenuation of wave energy by submerged or near-emergent coastal vegetation is one of the prominent methods of energy dissipation in areas with significant presence of wetlands. In this thesis, the nature of this dissipation in nearshore random...

Venkattaramanan, Aravinda

2014-04-28T23:59:59.000Z

69

Actinide removal from spent salts  

DOE Patents [OSTI]

A method for removing actinide contaminants (uranium and thorium) from the spent salt of a molten salt oxidation (MSO) reactor is described. Spent salt is removed from the reactor and analyzed to determine the contaminants present and the carbonate concentration. The salt is dissolved in water, and one or more reagents are added to precipitate the thorium as thorium oxide and/or the uranium as either uranium oxide or as a diuranate salt. The precipitated materials are filtered, dried and packaged for disposal as radioactive waste. About 90% of the thorium and/or uranium present is removed by filtration. After filtration, salt solutions having a carbonate concentration >20% can be dried and returned to the reactor for re-use. Salt solutions containing a carbonate concentration <20% require further clean-up using an ion exchange column, which yields salt solutions that contain less than 0.1 ppm of thorium or uranium.

Hsu, Peter C. (Pleasanton, CA); von Holtz, Erica H. (Livermore, CA); Hipple, David L. (Livermore, CA); Summers, Leslie J. (Livermore, CA); Adamson, Martyn G. (Danville, CA)

2002-01-01T23:59:59.000Z

70

Overview of Opportunities for Co-Location of Solar Energy Technologies and Vegetation  

SciTech Connect (OSTI)

Large-scale solar facilities have the potential to contribute significantly to national electricity production. Many solar installations are large-scale or utility-scale, with a capacity over 1 MW and connected directly to the electric grid. Large-scale solar facilities offer an opportunity to achieve economies of scale in solar deployment, yet there have been concerns about the amount of land required for solar projects and the impact of solar projects on local habitat. During the site preparation phase for utility-scale solar facilities, developers often grade land and remove all vegetation to minimize installation and operational costs, prevent plants from shading panels, and minimize potential fire or wildlife risks. However, the common site preparation practice of removing vegetation can be avoided in certain circumstances, and there have been successful examples where solar facilities have been co-located with agricultural operations or have native vegetation growing beneath the panels. In this study we outline some of the impacts that large-scale solar facilities can have on the local environment, provide examples of installations where impacts have been minimized through co-location with vegetation, characterize the types of co-location, and give an overview of the potential benefits from co-location of solar energy projects and vegetation. The varieties of co-location can be replicated or modified for site-specific use at other solar energy installations around the world. We conclude with opportunities to improve upon our understanding of ways to reduce the environmental impacts of large-scale solar installations.

Macknick, J.; Beatty, B.; Hill, G.

2013-12-01T23:59:59.000Z

71

What can I do with leftover turkey? Remove meat from turkey carcass and store in a covered  

E-Print Network [OSTI]

What can I do with leftover turkey? Remove meat from turkey carcass and store in a covered of chopped leftover turkey, 4 cups of chopped vegetables and 2 cups cooked rice, wild rice or noodles to 3 have blended. Add some parsley, bay leaves, and garlic for extra flavor. Salads: Add leftover turkey

Minnesota, University of

72

Forecast Technical Document Felling and Removals  

E-Print Network [OSTI]

Forecast Technical Document Felling and Removals Forecasts A document describing how volume fellings and removals are handled in the 2011 Production Forecast system. Tom Jenkins Robert Matthews Ewan Mackie Lesley Halsall #12;PF2011 ­ Felling and removals forecasts Background A fellings and removals

73

Ion Removal - Energy Innovation Portal  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation ProposedUsingFunInfrared LandResponses toInvestigatingAdaptedInvestor| EMSLAdvanced

74

Thermal Performance of Vegetative Roofing Systems  

SciTech Connect (OSTI)

Vegetative roofing, otherwise known as green or garden roofing, has seen tremendous growth in the last decade in the United States. The numerous benefits that green roofs provide have helped to fuel their resurgence in industrial and urban settings. There are many environmental and economical benefits that can be realized by incorporating a vegetative roof into the design of a building. These include storm-water retention, energy conservation, reduction in the urban heat island effect, increased longevity of the roofing membrane, the ability of plants to create biodiversity and filter air contaminants, and beautification of the surroundings by incorporating green space. The vegetative roof research project at Oak Ridge National Laboratory (ORNL) was initiated to quantify the thermal performance of various vegetative roofing systems relative to black and white roofs. Single Ply Roofing Institute (SPRI) continued its long-term commitment to cooperative research with ORNL in this project. Low-slope roof systems for this study were constructed and instrumented for continuous monitoring in the mixed climate of East Tennessee. This report summarizes the results of the annual cooling and heating loads per unit area of three vegetative roofing systems with side-by-side comparison to black and white roofing systems as well as a test section with just the growing media without plants. Results showed vegetative roofs reduced heat gain (reduced cooling loads) compared to the white control system due to the thermal mass, extra insulation, and evapo-transpiration associated with the vegetative roofing systems. The 4-inch and tray systems reduced the heat gain by approximately 61%, while the reduction with the 8-inch vegetative roof was found to be approximately 67%. The vegetative roofing systems were more effective in reducing heat gain than in reducing heat losses (heating loads). The reduction in heat losses for the 4-inch and tray systems were found to be approximately 40% in the mixed climate of East Tennessee. It should be noted that these values are climate dependent. Vegetative roofs also reduced the temperature (heat exposure) and temperature fluctuations (thermal stress) experienced by the membrane. In the cooling season of East Tennessee, the average peak temperature of the 4-inch and tray systems was found to be approximately 94 F cooler than the control black roofing system. The average temperature fluctuations at the membrane for the 4-inch and tray systems were found to be approximately 10 F compared to 125 F for black and 64 F for white systems. As expected, the 8-inch vegetative roof had the lowest fluctuations at approximately 2 F. Future work will include modeling of the energy performance of vegetative roof panels in the test climate of East Tennessee. The validated model then will be used to predict energy use in roofs with different insulation levels and in climates different from the test climate.

Desjarlais, Andre Omer [ORNL; Zaltash, Abdolreza [ORNL; Atchley, Jerald Allen [ORNL; Ennis, Mike J [ORNL

2010-01-01T23:59:59.000Z

75

Vegetation Indices to Aid Areal Evapotranspiration Estimations  

E-Print Network [OSTI]

Vegetation Indices to Aid Areal Evapotranspiration Estimations Jozsef Szilagyi1 Abstract: Multiyear Seevers and Ottmann 1994; Nicholson et al. 1996; Sz- ilagyi et al. 1998; Szilagyi and Parlange 1999; Szilagyi 2000 . Different authors drew differing conclusions about the appli- cability of NDVI to estimate

Szilagyi, Jozsef

76

Easy Gardening.....Harvesting and Handling Vegetables  

E-Print Network [OSTI]

Easy Gardening Joseph Masabni, Assistant Professor and Extension Horticulturist, The Texas A&M University System HARVESTING ? HANDLING ? STORING VEGETABLES -1- T ohelpensurethatthevegetables yougrowandprepareareofhigh quality.... Acknowledgments Thispublicationwasrevisedfromearlierversionswrittenby SamCotner,ProfessorEmeritusandformerExtension Horticulturist,andAlWagner,formerProfessorand ExtensionHorticulturist. -6- Produced by AgriLife Communications, The Texas A&M System Extension...

Cotner, Sam; Masabni, Joseph; Wagner, Al

2009-05-29T23:59:59.000Z

77

Circumpolar Arctic Tundra Vegetation Change Is Linked  

E-Print Network [OSTI]

of Plant Biology, Michigan State University, East Lansing, Michigan Received 7 December 2009; accepted 4Circumpolar Arctic Tundra Vegetation Change Is Linked to Sea Ice Decline Uma S. Bhatt*,1 Donald A Institute, and Department of Atmospheric Sciences, University of Alaska Fairbanks, Fairbanks, Alaska

Bhatt, Uma

78

Mexico HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Apply for Our Jobs Our Jobs Working at NNSA Blog Home content Four-Year Plan Mexico HEU Removal Mexico HEU Removal Location Mexico United States 24 24' 35.298" N, 102...

79

Arsenic removal and stabilization by synthesized pyrite  

E-Print Network [OSTI]

hydride generation atomic absorption spectrometry method for measuring arsenic species (As(III), As(V)). The synthesized pyrite was applied to remove arsenic and its maximum capacity for arsenic removal was measured in batch adsorption experiments to be 3...

Song, Jin Kun

2009-05-15T23:59:59.000Z

80

Libya HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Plan Libya HEU Removal Libya HEU Removal Location Libya United States 27 34' 9.5448" N, 17 24' 8.4384" E See map: Google Maps Javascript is required to view this map....

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Canada HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Plan Canada HEU Removal Canada HEU Removal Location Canada United States 53 47' 24.972" N, 104 35' 23.4384" W See map: Google Maps Javascript is required to view this map....

82

Israel HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Plan Israel HEU Removal Israel HEU Removal Location Israel United States 30 53' 18.2328" N, 34 52' 14.178" E See map: Google Maps Javascript is required to view this map....

83

Turkey HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Plan Turkey HEU Removal Turkey HEU Removal Location Turkey United States 38 26' 50.2044" N, 40 15' 14.0616" E See map: Google Maps Javascript is required to view this map...

84

Uzbekistan HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Uzbekistan HEU Removal Uzbekistan HEU Removal Location Uzbekistan United States 42 6' 56.196" N, 63 22' 8.9076" E See map: Google Maps Javascript is required to view this map...

85

France HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Four-Year Plan France HEU Removal France HEU Removal Location United States 45 44' 20.0544" N, 2 17' 6.5616" E See map: Google Maps Javascript is required to view this map...

86

Kazakhstan HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

HEU Removal Kazakhstan HEU Removal Location Kazakhstan United States 48 59' 44.1492" N, 67 3' 37.9692" E See map: Google Maps Javascript is required to view this map....

87

Ukraine HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Plan Ukraine HEU Removal Ukraine HEU Removal Location Ukraine United States 50 12' 24.8688" N, 25 50' 23.4384" E See map: Google Maps Javascript is required to view this map...

88

Chile HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Four-Year Plan Chile HEU Removal Chile HEU Removal Location United States 25 28' 1.4916" S, 69 33' 55.548" W See map: Google Maps Javascript is required to view this map...

89

Taiwan HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Plan Taiwan HEU Removal Taiwan HEU Removal Location Taiwan United States 24 35' 37.4964" N, 120 53' 36.798" E See map: Google Maps Javascript is required to view this map....

90

Romania HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Plan Romania HEU Removal Romania HEU Removal Location Romania United States 45 47' 1.932" N, 24 41' 50.1576" E See map: Google Maps Javascript is required to view this map....

91

Hungary HEU removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Plan Hungary HEU removal Hungary HEU removal Location Hungary United States 47 11' 51.6336" N, 19 41' 15" E See map: Google Maps Javascript is required to view this map....

92

Serbia HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Plan Serbia HEU Removal Serbia HEU Removal Location Serbia United States 44 22' 45.7068" N, 20 26' 4.452" E See map: Google Maps Javascript is required to view this map....

93

Japan HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Plan Japan HEU Removal Japan HEU Removal Location Japan United States 37 36' 59.5872" N, 140 5' 51.5616" E See map: Google Maps Javascript is required to view this map....

94

Poland HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Plan Poland HEU Removal Poland HEU Removal Location Poland United States 53 23' 50.2872" N, 17 50' 30.4692" E See map: Google Maps Javascript is required to view this map....

95

Italy HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Plan Italy HEU Removal Italy HEU Removal Location Italy United States 43 41' 3.4548" N, 11 28' 11.0172" E See map: Google Maps Javascript is required to view this map...

96

Vietnam HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Plan Vietnam HEU Removal Vietnam HEU Removal Location Vietnam United States 13 12' 30.8628" N, 108 19' 30.702" E See map: Google Maps Javascript is required to view this map....

97

Water Distribution and Removal Model  

SciTech Connect (OSTI)

The design of the Yucca Mountain high level radioactive waste repository depends on the performance of the engineered barrier system (EBS). To support the total system performance assessment (TSPA), the Engineered Barrier System Degradation, Flow, and Transport Process Model Report (EBS PMR) is developed to describe the thermal, mechanical, chemical, hydrological, biological, and radionuclide transport processes within the emplacement drifts, which includes the following major analysis/model reports (AMRs): (1) EBS Water Distribution and Removal (WD&R) Model; (2) EBS Physical and Chemical Environment (P&CE) Model; (3) EBS Radionuclide Transport (EBS RNT) Model; and (4) EBS Multiscale Thermohydrologic (TH) Model. Technical information, including data, analyses, models, software, and supporting documents will be provided to defend the applicability of these models for their intended purpose of evaluating the postclosure performance of the Yucca Mountain repository system. The WD&R model ARM is important to the site recommendation. Water distribution and removal represents one component of the overall EBS. Under some conditions, liquid water will seep into emplacement drifts through fractures in the host rock and move generally downward, potentially contacting waste packages. After waste packages are breached by corrosion, some of this seepage water will contact the waste, dissolve or suspend radionuclides, and ultimately carry radionuclides through the EBS to the near-field host rock. Lateral diversion of liquid water within the drift will occur at the inner drift surface, and more significantly from the operation of engineered structures such as drip shields and the outer surface of waste packages. If most of the seepage flux can be diverted laterally and removed from the drifts before contacting the wastes, the release of radionuclides from the EBS can be controlled, resulting in a proportional reduction in dose release at the accessible environment. The purposes of this WD&R model (CRWMS M&O 2000b) are to quantify and evaluate the distribution and drainage of seepage water within emplacement drifts during the period of compliance for post-closure performance. The model bounds the fraction of water entering the drift that will be prevented from contacting the waste by the combined effects of engineered controls on water distribution and on water removal. For example, water can be removed during pre-closure operation by ventilation and after closure by natural drainage into the fractured rock. Engineered drains could be used, if demonstrated to be necessary and effective, to ensure that adequate drainage capacity is provided. This report provides the screening arguments for certain Features, Events, and Processes (FEPs) that are related to water distribution and removal in the EBS. Applicable acceptance criteria from the Issue Resolution Status Reports (IRSRs) developed by the U.S. Nuclear Regulatory Commission (NRC 1999a; 1999b; 1999c; and 1999d) are also addressed in this document.

Y. Deng; N. Chipman; E.L. Hardin

2005-08-26T23:59:59.000Z

98

Removing Stains from Washable Fabrics.  

E-Print Network [OSTI]

Page Numbers Stain Page Numbers Acne medicine Blueberry Special 9 Wet 8 Adhesive tape Dye 8 Special 9 Butter Alcoholic beverages Dry 8 Wet 8 Oil 8 Tannin 8 Calamine lotion Asphalt Combination 8 Combination 8 Dye 8 Dye 8 Candle wax Automotive... the most gentle to the most harsh, so always stop treatments as soon as the stain has been removed. Dry Type Stains Dissolve the stain with a grease solvent. Lubricate the stain with dry spotter, coconut oil or mineral oil (sold in health food...

Beard, Ann Vanderpoorten

1988-01-01T23:59:59.000Z

99

Automatic Eyeglasses Removal from Face Images  

E-Print Network [OSTI]

Automatic Eyeglasses Removal from Face Images Chenyu Wu, Ce Liu, Heung-Yueng Shum, Member, IEEE an intelligent image editing and face synthesis system that automatically removes eyeglasses from an input frontal face image. Although conventional image editing tools can be used to remove eyeglasses by pixel

Narasayya, Vivek

100

An application of predictive vegetation mapping to mountain vegetation in Sweden  

E-Print Network [OSTI]

community data as the dependent variable and various environmental data as the independent variables thought to control or correlate with vegetation distributions. The environmental data were either obtained from existing digital datasets or derived from...

Green, Janet Alexis

2006-04-12T23:59:59.000Z

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Method of making thermally removable epoxies  

DOE Patents [OSTI]

A method of making a thermally-removable epoxy by mixing a bis(maleimide) compound to a monomeric furan compound containing an oxirane group to form a di-epoxy mixture and then adding a curing agent at temperatures from approximately room temperature to less than approximately 90.degree. C. to form a thermally-removable epoxy. The thermally-removable epoxy can be easily removed within approximately an hour by heating to temperatures greater than approximately 90.degree. C. in a polar solvent. The epoxy material can be used in protecting electronic components that may require subsequent removal of the solid material for component repair, modification or quality control.

Loy, Douglas A. (Albuquerque, NM); Wheeler, David R. (Albuquerque, NM); Russick, Edward M. (Rio Rancho, NM); McElhanon, James R. (Albuquerque, NM); Saunders, Randall S. (late of Albuquerque, NM)

2002-01-01T23:59:59.000Z

102

Momentum and scalar transport in vegetated shear flows  

E-Print Network [OSTI]

Environmental aquatic flows are seldom free of vegetative influence. However, the impact of submerged vegetation on the hydrodynamics and mixing processes in aquatic flows remains poorly understood. In this thesis, I present ...

Ghisalberti, Marco (Marco Andrea), 1976-

2005-01-01T23:59:59.000Z

103

Interactions between currents and the spatial structure of aquatic vegetation  

E-Print Network [OSTI]

Vegetation is present in nearly all aquatic environments, ranging from meandering streams to constructed channels and rivers, as well as in lakes and coastal zones. This vegetation grows in a wide range of flow environments ...

Rominger, Jeffrey T. (Jeffrey Tsaros)

2009-01-01T23:59:59.000Z

104

Straight Vegetable Oil as a Diesel Fuel? (Fact Sheet)  

SciTech Connect (OSTI)

Discusses the use of straight vegetable oil as a diesel fuel and the use of biodiesel as a transportation fuel.

Not Available

2010-05-01T23:59:59.000Z

105

Vegetation survey of PEN Branch wetlands  

SciTech Connect (OSTI)

A survey was conducted of vegetation along Pen Branch Creek at Savannah River Site (SRS) in support of K-Reactor restart. Plants were identified to species by overstory, understory, shrub, and groundcover strata. Abundance was also characterized and richness and diversity calculated. Based on woody species basal area, the Pen Branch delta was the most impacted, followed by the sections between the reactor and the delta. Species richness for shrub and groundcover strata were also lowest in the delta. No endangered plant species were found. Three upland pine areas were also sampled. In support of K Reactor restart, this report summarizes a study of the wetland vegetation along Pen Branch. Reactor effluent enters Indian Grove Branch and then flows into Pen Branch and the Pen Branch Delta.

Not Available

1991-01-01T23:59:59.000Z

106

Melter Glass Removal and Dismantlement  

SciTech Connect (OSTI)

The U.S. Department of Energy (DOE) has been using vitrification processes to convert high-level radioactive waste forms into a stable glass for disposal in waste repositories. Vitrification facilities at the Savannah River Site (SRS) and at the West Valley Demonstration Project (WVDP) are converting liquid high-level waste (HLW) by combining it with a glass-forming media to form a borosilicate glass, which will ensure safe long-term storage. Large, slurry fed melters, which are used for this process, were anticipated to have a finite life (on the order of two to three years) at which time they would have to be replaced using remote methods because of the high radiation fields. In actuality the melters useable life spans have, to date, exceeded original life-span estimates. Initial plans called for the removal of failed melters by placing the melter assembly into a container and storing the assembly in a concrete vault on the vitrification plant site pending size-reduction, segregation, containerization, and shipment to appropriate storage facilities. Separate facilities for the processing of the failed melters currently do not exist. Options for handling these melters include (1) locating a facility to conduct the size-reduction, characterization, and containerization as originally planned; (2) long-term storing or disposing of the complete melter assembly; and (3) attempting to refurbish the melter and to reuse the melter assembly. The focus of this report is to look at methods and issues pertinent to size-reduction and/or melter refurbishment in particular, removing the glass as a part of a refurbishment or to reduce contamination levels (thus allowing for disposal of a greater proportion of the melter as low level waste).

Richardson, BS

2000-10-31T23:59:59.000Z

107

Improving vegetable preference and consumption among preschool children: evaluating results from an educational intervention using vegetable gardening  

E-Print Network [OSTI]

's exposure to a variety of vegetables through the incorporation of weekly gardening supplemented with classroom activities. The objective of this study was to evaluate the usefulness of vegetable gardening to improve preschool children's affective responses...

Lorenz, Saundra Gail

2002-01-01T23:59:59.000Z

108

?Aceite Vegetal Puro Como Combustible Diesel? (Straight Vegetable Oil as a Diesel Fuel? Spanish Version) (Fact Sheet)  

SciTech Connect (OSTI)

Discusses the use of straight vegetable oil as a diesel fuel and the use of biodiesel as a transportation fuel.

Not Available

2010-06-01T23:59:59.000Z

109

Removal of metal ions from aqueous solution  

DOE Patents [OSTI]

A method of removing heavy metals from aqueous solution, a composition of matter used in effecting said removal, and apparatus used in effecting said removal. One or more of the polypeptides, poly (.gamma.-glutamylcysteinyl)glycines, is immobilized on an inert material in particulate form. Upon contact with an aqueous solution containing heavy metals, the polypeptides sequester the metals, removing them from the solution. There is selectivity of poly (.gamma.-glutamylcysteinyl)glycines having a particular number of monomer repeat unit for particular metals. The polypeptides are easily regenerated by contact with a small amount of an organic acid, so that they can be used again to remove heayv metals from solution. This also results in the removal of the metals from the column in a concentrated form.

Jackson, Paul J. (both Los Alamos, NM); Delhaize, Emmanuel (both Los Alamos, NM); Robinson, Nigel J. (Durham, GB2); Unkefer, Clifford J. (Los Alamos, NM); Furlong, Clement (Seattle, WA)

1990-11-13T23:59:59.000Z

110

Removal of metal ions from aqueous solution  

DOE Patents [OSTI]

A method of removing heavy metals from aqueous solution, a composition of matter used in effecting said removal, and apparatus used in effecting said removal. One or more of the polypeptides, poly (.gamma.-glutamylcysteinyl)glycines, is immobilized on an inert material in particulate form. Upon contact with an aqueous solution containing heavy metals, the polypeptides sequester the metals, removing them from the solution. There is selectivity of poly (.gamma.-glutamylcysteinyl)glycines having a particular number of monomer repeat units for particular metals. The polypeptides are easily regenerated by contact with a small amount of an organic acid, so that they can be used again to remove heavy metals from solution. This also results in the removal of the metals from the column in a concentrated form.

Jackson, Paul J. (Los Alamos, NM); Delhaize, Emmanuel (Los Alamos, NM); Robinson, Nigel J. (Durham, GB2); Unkefer, Clifford J. (Los Alamos, NM); Furlong, Clement (Seattle, WA)

1990-01-01T23:59:59.000Z

111

TMI-2 reactor vessel head removal  

SciTech Connect (OSTI)

This report describes the safe removal and storage of the Three Mile Island Unit 2 reactor vessel head. The head was removed in July 1984 to permit the removal of the plenum and the reactor core, which were damaged during the 1979 accident. From July 1982, plans and preparations were made using a standard head removal procedure modified by the necessary precautions and changes to account for conditions caused by the accident. After data acquisition, equipment and structure modifications, and training the head was safely removed and stored and the internals indexing fixture and a work platform were installed on top of the vessel. Dose rates during and after the operation were lower than expected; lessons were learned from the operation which will be applied to the continuing fuel removal operations activities.

Bengel, P.R.; Smith, M.D.; Estabrook, G.A.

1984-12-01T23:59:59.000Z

112

TMI-2 reactor vessel head removal  

SciTech Connect (OSTI)

This report describes the safe removal and storage of the Three Mile Island Unit 2 (TMI-2) reactor vessel head. The head was removed in July 1984 to permit the removal of the plenum and the reactor core, which were damaged during the 1979 accident. From July 1982, plans and preparations were made using a standard head removal procedure modified by the necessary precautions and changes to account for conditions caused by the accident. After data acquisition, equipment and structure modifications, and training, the head was safely removed and stored; and the internals indexing fixture and a work platform were installed on top of the vessel. Dose rates during and after the operation were lower than expected; lessons were learned from the operation which will be applied to the continuing fuel removal operations activities.

Bengel, P.R.; Smith, M.D.; Estabrook, G.A.

1985-09-01T23:59:59.000Z

113

Process for particulate removal from coal liquids  

DOE Patents [OSTI]

Suspended solid particulates are removed from liquefied coal products by first subjecting such products to hydroclone action for removal in the underflow of the larger size particulates, and then subjecting the overflow from said hydroclone action, comprising the residual finer particulates, to an electrostatic field in an electrofilter wherein such finer particulates are deposited in the bed of beads of dielectric material on said filter. The beads are periodically cleaned by backwashing to remove the accumulated solids.

Rappe, Gerald C. (Macungie, PA)

1983-01-01T23:59:59.000Z

114

Method for removing contaminants from plastic resin  

DOE Patents [OSTI]

A resin recycling method that produces essentially contaminant-free synthetic resin material in an environmentally safe and economical manner. The method includes receiving the resin in container form. The containers are then ground into resin particles. The particles are exposed to a solvent, the solvent contacting the resin particles and substantially removing contaminants on the resin particles. After separating the particles and the resin, a solvent removing agent is used to remove any residual solvent remaining on the resin particles after separation.

Bohnert, George W. (Harrisonville, MO); Hand, Thomas E. (Lee's Summit, MO); DeLaurentiis, Gary M. (Jamestown, CA)

2008-12-09T23:59:59.000Z

115

Method of making thermally removable polymeric encapsulants  

DOE Patents [OSTI]

A method of making a thermally-removable encapsulant by heating a mixture of at least one bis(maleimide) compound and at least one monomeric tris(furan) or tetrakis(furan) compound at temperatures from above room temperature to less than approximately 90.degree. C. to form a gel and cooling the gel to form the thermally-removable encapsulant. The encapsulant can be easily removed within approximately an hour by heating to temperatures greater than approximately 90.degree. C., preferably in a polar solvent. The encapsulant can be used in protecting electronic components that may require subsequent removal of the encapsulant for component repair, modification or quality control.

Small, James H. (Santa Fe, NM); Loy, Douglas A. (Albuquerque, NM); Wheeler, David R. (Albuquerque, NM); McElhanon, James R. (Albuquerque, NM); Saunders, Randall S. (late of Albuquerque, NM)

2001-01-01T23:59:59.000Z

116

Australia HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Australia HEU Removal | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing Proliferation Powering the...

117

Argentina HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Argentina HEU Removal | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing Proliferation Powering the...

118

System for removing contaminants from plastic resin  

DOE Patents [OSTI]

A resin recycling system that produces essentially contaminant-free synthetic resin material in an environmentally safe and economical manner. The system includes receiving the resin in container form. A grinder grinds the containers into resin particles. The particles are exposed to a solvent in one or more solvent wash vessels, the solvent contacting the resin particles and substantially removing contaminants on the resin particles. A separator is used to separate the resin particles and the solvent. The resin particles are then placed in solvent removing element where they are exposed to a solvent removing agent which removes any residual solvent remaining on the resin particles after separation.

Bohnert, George W. (Harrisonville, MO); Hand, Thomas E. (Lee's Summit, MO); DeLaurentiis, Gary M. (Jamestown, CA)

2010-11-23T23:59:59.000Z

119

Sweden Plutonium Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Sweden Plutonium Removal | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing Proliferation Powering the...

120

Vegetation Description, Rare Plant Inventory, and Vegetation Monitoring for Craig Mountain, Idaho.  

SciTech Connect (OSTI)

The Craig Mountain Wildlife Mitigation Area was purchased by Bonneville Power Administration (BPA) as partial mitigation for wildlife losses incurred with the inundation of Dworshak Reservoir on the North Fork Clearwater River. Upon completion of the National Environmental Protection Act (NEPA) process, it is proposed that title to mitigation lands will be given to the Idaho Department of Fish and Game (IDFG). Craig Mountain is located at the northern end of the Hells Canyon Ecosystem. It encompasses the plateau and steep canyon slopes extending from the confluence of the Snake and Salmon rivers, northward to near Waha, south of Lewiston, Idaho. The forested summit of Craig Mountain is characterized by gently rolling terrain. The highlands dramatically break into the canyons of the Snake and Salmon rivers at approximately the 4,700 foot contour. The highly dissected canyons are dominated by grassland slopes containing a mosaic of shrubfield, riparian, and woodland habitats. During the 1993 and 1994 field seasons, wildlife, habitat/vegetation, timber, and other resources were systematically inventoried at Craig Mountain to provide Fish and Game managers with information needed to draft an ecologically-based management plan. The results of the habitat/vegetation portion of the inventory are contained in this report. The responsibilities for the Craig Mountain project included: (1) vegetation data collection, and vegetation classification, to help produce a GIS-generated Craig Mountain vegetation map, (2) to determine the distribution and abundance of rare plants populations and make recommendations concerning their management, and (3) to establish a vegetation monitoring program to evaluate the effects of Fish and Game management actions, and to assess progress towards meeting habitat mitigation goals.

Mancuso, Michael; Moseley, Robert

1994-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Long-Term Hydrologic Responses To Shrub Removal In A SW Texas Rangeland: Using Soil Chloride To Estimate Deep Drainage  

E-Print Network [OSTI]

LONG-TERM HYDROLOGIC RESPONSES TO SHRUB REMOVAL IN A SW TEXAS RANGELAND: USING SOIL CHLORIDE TO ESTIMATE DEEP DRAINAGE A Thesis by DAVID ANTHONY BARRE Submitted to the Office of Graduate Studies of Texas A&M University... of the study were to identify those biotic and abiotic factors facilitating deep drainage and to examine differences in recharge for the years following clearing of natural shrub vegetation. Soil chloride was examined to estimate long-term recharge rates...

Barre, David Anthony

2010-10-12T23:59:59.000Z

122

Effects of various uranium leaching procedures on soil: Short-term vegetation growth and physiology. Progress report, April 1994  

SciTech Connect (OSTI)

Significant volumes of soil containing elevated levels of uranium exist in the eastern United States. The contamination resulted from the development of the nuclear industry in the United States requiring a large variety of uranium products. The contaminated soil poses a collection and disposal problem of a magnitude that justifies the development of decontamination methods. Consequently, the Department of Energy (DOE) Office of Technology Development formed the Uranium Soils Integrated Demonstration (USID) program to address the problem. The fundamental goal of the USID task group has been the selective extraction/leaching or removal of uranium from soil faster, cheaper, and safer than what can be done using current conventional technologies. The objective is to selectively remove uranium from soil without seriously degrading the soil`s physicochemical characteristics and without generating waste that is difficult to manage and/or dispose of. However, procedures developed for removing uranium from contaminated soil have involved harsh chemical treatments that affect the physicochemical properties of the soil. The questions are (1) are the changes in soil properties severe enough to destroy the soil`s capacity to support and sustain vegetation growth and survival? and (2) what amendments might be made to the leached soil to return it to a reasonable vegetation production capacity? This study examines the vegetation-support capacity of soil that had been chemically leached to remove uranium. The approach is to conduct short-term germination and phytotoxicity tests for evaluating soils after they are subjected to various leaching procedures followed by longer term pot studies on successfully leached soils that show the greatest capacity to support plant growth. This report details the results from germination and short-term phytotoxicity testing of soils that underwent a variety of leaching procedures at the bench scale at ORNL and at the pilot plant at Fernald.

Edwards, N.T.

1994-08-01T23:59:59.000Z

123

Method And Apparatus For Arbitrarily Large Capacity Removable Media  

DOE Patents [OSTI]

A method and apparatus to handle multiple sets of removable media within a storage system. A first set of removable media are mounted on a set of drives. Data is accepted until the first set of removable media is filled. A second set of removable media is mounted on the drives, while the first set of removable media is removed. When the change in removable media is complete, writing of data proceeds on the second set of removable media. Data may be buffered while the change in removable media occurs. Alternatively, two sets of removable media may be mounted at the same time. When the first set of removable media is filled to a selected amount, the second set of removable media may then be used to write the data. A third set of removable media is set up or mounted for use, while the first set of removable media is removed.

Milligan, Charles A. (Golden, CO); Hughes, James P. (Lino Lakes, MN); Debiez; Jacques (Cugnaux, FR)

2003-04-08T23:59:59.000Z

124

Method of removing contaminants from plastic resins  

DOE Patents [OSTI]

A method for removing contaminants from synthetic resin material containers using a first organic solvent system and a second carbon dioxide system. The organic solvent is utilized for removing the contaminants from the synthetic resin material and the carbon dioxide is used to separate any residual organic solvent from the synthetic resin material.

Bohnert, George W. (Harrisonville, MO); Hand, Thomas E. (Lee's Summit, MO); DeLaurentiis, Gary M. (Jamestown, CA)

2008-11-18T23:59:59.000Z

125

Method of removing contaminants from plastic resins  

DOE Patents [OSTI]

A method for removing contaminants from synthetic resin material containers using a first organic solvent system and a second carbon dioxide system. The organic solvent is utilized for removing the contaminants from the synthetic resin material and the carbon dioxide is used to separate any residual organic solvent from the synthetic resin material.

Bohnert,George W. (Harrisonville, MO); Hand,Thomas E. (Lee's Summit, MO); Delaurentiis,Gary M. (Jamestown, CA)

2007-08-07T23:59:59.000Z

126

Method for removing contaminants from plastic resin  

DOE Patents [OSTI]

A method for removing contaminants from synthetic resin material containers using a first organic solvent system and a second carbon dioxide system. The organic solvent is utilized for removing the contaminants from the synthetic resin material and the carbon dioxide is used to separate any residual organic solvent from the synthetic resin material.

Bohnert, George W. (Harrisonville, MO); Hand, Thomas E. (Lee's Summit, MO); DeLaurentiis, Gary M. (Jamestown, CA)

2008-12-30T23:59:59.000Z

127

arctic vegetation damage: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

gradient. Here we examine the complex interrelationships between patterned ground, climate, vegetation and soil along a north-south transect through all five bioclimate...

128

Supplement Analysis for the Transmission System Vegetation Management...  

Broader source: Energy.gov (indexed) [DOE]

14, 2001 REPLY TO ATTN OF: KEP-4 SUBJECT: Supplement Analysis for the Transmission System Vegetation Management Program FEIS (DOEEIS-0285SA-35) James Jellison - TFOOlympia...

129

Supplement Analysis for the Transmission System Vegetation Management...  

Broader source: Energy.gov (indexed) [DOE]

5, 2001 REPLY TO ATTN OF: KEPZ992 SUBJECT: Supplement Analysis for the Transmission System Vegetation Management Program FEIS (DOEEIS-0285SA-25) Elizabeth Johnson - TFRThe...

130

The effects of elephant and mesoherbivores on woody vegetation.  

E-Print Network [OSTI]

??Herbivores are important drivers and have a longstanding history in shaping our terrestrial environments. However, during the past decades, changes in woody vegetation in savanna… (more)

Lagendijk, Daisy Diana Georgette.

2011-01-01T23:59:59.000Z

131

Local Incentive-Based Policy for Vegetable-Agroforestry: alocally...  

Open Energy Info (EERE)

Vegetable-Agroforestry: a locally-appropriate adaptation and mitigation action (LAAMA) to climate change Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Local...

132

affects arabidopsis vegetative: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

The vegetation reacts with changes in species composition and a decrease in biodiversity. Artificial snowing modifies some of these impacts: The soil frost is mitigated due to an...

133

african vegetation phenology: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

rainy season. Further research is needed to address interaction between groundwater under climate change. 1. Introduction "Vegetation phenology" refers to the periodic biological...

134

Removable bearing arrangement for a wind turbine generator  

DOE Patents [OSTI]

A wind generator having removable change-out bearings includes a rotor and a stator, locking bolts configured to lock the rotor and stator, a removable bearing sub-assembly having at least one shrunk-on bearing installed, and removable mounting bolts configured to engage the bearing sub-assembly and to allow the removable bearing sub-assembly to be removed when the removable mounting bolts are removed.

Bagepalli, Bharat Sampathkumaran; Jansen, Patrick Lee; Gadre, Aniruddha Dattatraya

2010-06-15T23:59:59.000Z

135

Method for changing removable bearing for a wind turbine generator  

DOE Patents [OSTI]

A wind generator having removable change-out bearings includes a rotor and a stator, locking bolts configured to lock the rotor and stator, a removable bearing sub-assembly having at least one shrunk-on bearing installed, and removable mounting bolts configured to engage the bearing sub-assembly and to allow the removable bearing sub-assembly to be removed when the removable mounting bolts are removed.

Bagepalli, Bharat Sampathkumaran (Niskayuna, NY); Jansen, Patrick Lee (Scotia, NY); Gadre, Aniruddha Dattatraya (Rexford, NY)

2008-04-22T23:59:59.000Z

136

Sulfur dioxide removal by enhanced electrostatics  

SciTech Connect (OSTI)

The economic removal of sulfur dioxide (SO{sub 2}) still represents a significant technical challenge which could determine the use of certain types of fossil fuels for energy production. This paper will present the preliminary results of an innovative research project utilizing a low-cost wet electrostatic precipitator to remove sulfur dioxide. There are many aspects for gas removal in an electrostatic precipitator which are not currently being used. This project utilizes electron attachment of free electrons onto gas molecules and ozone generation to remove sulfur dioxide which is a typical flue gas pollutant. This research was conducted on a bench-scale, wet electrostatic precipitator. A direct-current negative discharge corona is used to generate the ozone in-situ. This ozone will be used to oxidize SO{sub 2} to form sulfuric acid, which is very soluble in water. However, it is believed that the primary removal mechanism is electron attachment of the free electrons from the corona which force the SO{sub 2} to go to equilibrium with the water and be removed from the gas stream. Forcing the equilibrium has been shown to achieve removal efficiencies of up to 70%. The bench scale unit has been designed to operate wet or dry, positive and negative for comparison purposes. The applied dc voltage is variable from 0 to 100 kV, the flow rate is a nominal 7 m{sup 3}/hr and the collecting electrode area is 0.20 m{sup 2}. Tests are conducted on a simulated flue gas stream with SO{sub 2} ranging from 0 to 4,000 ppmv. This paper presents the results of tests conducted to determine the effect of operating conditions on removal efficiency. The removal efficiency was found to vary with gas residence time, water flow rate, inlet concentration, applied power, and the use of corona pulsing.

Larkin, K.; Tseng, C.; Keener, T.C.; Khang, S.J. [Univ. of Cincinnati, OH (United States)

1997-12-31T23:59:59.000Z

137

In situ removal of contamination from soil  

DOE Patents [OSTI]

A process of remediation of cationic heavy metal contamination from soil utilizes gas phase manipulation to inhibit biodegradation of a chelating agent that is used in an electrokinesis process to remove the contamination. The process also uses further gas phase manipulation to stimulate biodegradation of the chelating agent after the contamination has been removed. The process ensures that the chelating agent is not attacked by bioorganisms in the soil prior to removal of the contamination, and that the chelating agent does not remain as a new contaminant after the process is completed. 5 figs.

Lindgren, E.R.; Brady, P.V.

1997-10-14T23:59:59.000Z

138

In situ removal of contamination from soil  

DOE Patents [OSTI]

A process of remediation of cationic heavy metal contamination from soil utilizes gas phase manipulation to inhibit biodegradation of a chelating agent that is used in an electrokinesis process to remove the contamination, and further gas phase manipulation to stimulate biodegradation of the chelating agent after the contamination has been removed. The process ensures that the chelating agent is not attacked by bioorganisms in the soil prior to removal of the contamination, and that the chelating agent does not remain as a new contaminant after the process is completed.

Lindgren, Eric R. (Albuquerque, NM); Brady, Patrick V. (Albuquerque, NM)

1997-01-01T23:59:59.000Z

139

Effects of juniper removal by shearing and dozing on seedbed preparation and vegetation establishment in the Lampasas Cut Plain, Texas  

E-Print Network [OSTI]

drained and clayey. While both soils series are relatively shallow, the solum of the Evant is deeper (36-50 cm) than the Eckrant-Rock outcrop series (15-38 cm). In both soils, plant productivity is limited by a shallow depth of the root-limiting layer...

Mannel, Cheryl K.

2009-05-15T23:59:59.000Z

140

Vegetable Oil from Leaves and Stems: Vegetative Production of Oil in a C4 Crop  

SciTech Connect (OSTI)

PETRO Project: Arcadia Biosciences, in collaboration with the University of California-Davis, is developing plants that produce vegetable oil in their leaves and stems. Ordinarily, these oils are produced in seeds, but Arcadia Biosciences is turning parts of the plant that are not usually harvested into a source of concentrated energy. Vegetable oil is a concentrated source of energy that plants naturally produce and is easily separated after harvest. Arcadia Biosciences will isolate traits that control oil production in seeds and transfer them into leaves and stems so that all parts of the plants are oil-rich at harvest time. After demonstrating these traits in a fast-growing model plant, Arcadia Biosciences will incorporate them into a variety of dedicated biofuel crops that can be grown on land not typically suited for food production

None

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Part removal of 3D printed parts  

E-Print Network [OSTI]

An experimental study was performed to understand the correlation between printing parameters in the FDM 3D printing process, and the force required to remove a part from the build platform of a 3D printing using a patent ...

Peńa Doll, Mateo

2014-01-01T23:59:59.000Z

142

Install Removable Insulation on Valves and Fittings  

SciTech Connect (OSTI)

This revised ITP tip sheet on installing removable insulation on valves and fittings provides how-to advice for improving the system using low-cost, proven practices and technologies.

Not Available

2006-01-01T23:59:59.000Z

143

Method of removing polychlorinated biphenyl from oil  

DOE Patents [OSTI]

Polychlorinated biphenyls are removed from oil by extracting the biphenyls into methanol. The mixture of methanol and extracted biphenyls is distilled to separate methanol therefrom, and the methanol is recycled for further use in extraction of biphenyls from oil.

Cook, G.T.; Holshouser, S.K.; Coleman, R.M.; Harless, C.E.; Whinnery, W.N. III

1982-03-17T23:59:59.000Z

144

Laser removal of sludge from steam generators  

DOE Patents [OSTI]

A method of removing unwanted chemical deposits known as sludge from the metal surfaces of steam generators with laser energy is provided. Laser energy of a certain power density, of a critical wavelength and frequency, is intermittently focused on the sludge deposits to vaporize them so that the surfaces are cleaned without affecting the metal surface (sludge substrate). Fiberoptic tubes are utilized for laser beam transmission and beam direction. Fiberoptics are also utilized to monitor laser operation and sludge removal.

Nachbar, Henry D. (Ballston Lake, NY)

1990-01-01T23:59:59.000Z

145

CX-011230: Categorical Exclusion Determination | Department of...  

Broader source: Energy.gov (indexed) [DOE]

Determination Artesia Tap- Southwest Rangely 138 Kilovolt Transmission Line Danger Tree and Herbicide Treatment for Vegetation Management CX(s) Applied: B1.3 Date: 09262013...

146

Translational genomics of Vegetable Crops Las Vegas, NV  

E-Print Network [OSTI]

Translational genomics of Vegetable Crops Las Vegas, NV July 21, 2005 David Francis and Allen Van Deynze At the recent ASHS meetings in Las Vegas, a workshop "Translational Genomics of Vegetable Crops interventions" (Minna and Gazdar, 1996). In applied plant science, "translational genomics" implies

Douches, David S.

147

ASSISTANT PROFESSOR Sustainable Vegetable Production and Nutrition Systems  

E-Print Network [OSTI]

management that builds collaboratively on MSU's strengths in vegetable production and sustainable croppingASSISTANT PROFESSOR Sustainable Vegetable Production and Nutrition Systems The Department of Horticulture (http://www.hrt.msu.edu) in the College of Agriculture and Natural Resources at Michigan State

Isaacs, Rufus

148

FRUIT & VEGETABLE GROWERS MANUAL FOR THE BEGINNING GROWER  

E-Print Network [OSTI]

MINNESOTA FRUIT & VEGETABLE GROWERS MANUAL FOR THE BEGINNING GROWER Developed by the University & Outreach Assistance Partnership Program through a partnership agreement with the Minnesota Fruit before I harvest my produce? 135 3. When should I harvest my fruits and vegetables? 136 4. How should I

Amin, S. Massoud

149

Stream Temperature Response to Three Riparian Vegetation Scenarios  

E-Print Network [OSTI]

. Stream temperature response to three distinct riparian conditions were then modeled: open, in vegetation loss can increase other processes that play a role in heat exchange between the atmosphere local near-stream air mass transfer (18). Recent research on the effects of riparian vegetation

Selker, John

150

Classification of Sweden's Forest and Alpine Vegetation Using Optical  

E-Print Network [OSTI]

Classification of Sweden's Forest and Alpine Vegetation Using Optical Satellite and Inventory Data of Sweden's Forest and Alpine Vegetation Using Optical Satellite and Inventory Data. Abstract Creation photo-interpretation, or ground-based inventories. National inventories are a potential source

151

Oak Woodland Vegetation Dynamics: A State and Transition Approach1  

E-Print Network [OSTI]

into a format that is sensible and accessible to natural resource managers. State and transition models have93 Oak Woodland Vegetation Dynamics: A State and Transition Approach1 Melvin R. George2 and Maximo and transition format. Keywords: Oak-woodlands, state and transition models, succession, vegetation dynamics

Standiford, Richard B.

152

The vegetation of Yucca Mountain: Description and ecology  

SciTech Connect (OSTI)

Vegetation at Yucca Mountain, Nevada, was monitored over a six-year period, from 1989 through 1994. Yucca Mountain is located at the northern limit of the Mojave Desert and is the only location being studied as a potential repository for high-level nuclear waste. Site characterization consists of a series of multidisciplinary, scientific investigations designed to provide detailed information necessary to assess the suitability of the Yucca Mountain Site as a repository. This vegetation description establishes a baseline for determining the ecological impact of site characterization activities; it porvides input for site characterization research and modeling; and it clarifies vegetation community dynamics and relationships to the physical environment. A companion study will describe the impact of site characterization of vegetation. Cover, density, production, and species composition of vascular plants were monitored at 48 Ecological Study Plots (ESPs) stratified in four vegetation associations. Precipitation, soil moisture, and maximum and minimum temperatures also were measured at each study plot.

NONE

1996-03-29T23:59:59.000Z

153

Selective Removal of Lanthanides from Natural Waters, Acidic...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Removal of Lanthanides from Natural Waters, Acidic Streams and Dialysate. Selective Removal of Lanthanides from Natural Waters, Acidic Streams and Dialysate. Abstract: The...

154

Y-12 Removes Nuclear Materials from Two Facilities to Reduce...  

National Nuclear Security Administration (NNSA)

Home Field Offices Welcome to the NNSA Production Office NPO News Releases Y-12 Removes Nuclear Materials from Two Facilities ... Y-12 Removes Nuclear Materials from...

155

Oak Ridge Removes Laboratory's Greatest Source of Groundwater...  

Broader source: Energy.gov (indexed) [DOE]

Removes Laboratory's Greatest Source of Groundwater Contamination Oak Ridge Removes Laboratory's Greatest Source of Groundwater Contamination May 1, 2012 - 12:00pm Addthis Workers...

156

Vehicle Technologies Office Merit Review 2014: Removing Barriers...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Review 2014: Removing Barriers, Implementing Policies and Advancing Alternative Fuels Markets in New England Vehicle Technologies Office Merit Review 2014: Removing Barriers,...

157

Evaluation of Passive and Active Soot Filters for Removal of...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Passive and Active Soot Filters for Removal of Particulate Emissions from Diesel Engines Evaluation of Passive and Active Soot Filters for Removal of Particulate Emissions from...

158

Particulate Matter Sampling and Volatile Organic Compound Removal...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Organic Compound Removal for Characterization of Spark Ignited Direct Injection Engine Particulate Matter Sampling and Volatile Organic Compound Removal for Characterization...

159

Interactions among flow, sediment deposition and aquatic vegetation in a channel  

E-Print Network [OSTI]

Aquatic vegetation is commonly present in rivers in many forms. This thesis consists of two studies, which examine the flow structure around a patch of emergent, rigid vegetation in a laboratory channel. The vegetation ...

Zong, Lijun

2011-01-01T23:59:59.000Z

160

Laboratory experiments and numerical modeling of wave attenuation through artificial vegetation  

E-Print Network [OSTI]

It is commonly known that coastal vegetation dissipates energy and aids in shoreline protection by damping incoming waves and depositing sediment in vegetated regions. However, this critical role of vegetation to dampen wave forces is not fully...

Augustin, Lauren Nicole

2009-05-15T23:59:59.000Z

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Method of making thermally removable polyurethanes  

DOE Patents [OSTI]

A method of making a thermally-removable polyurethane material by heating a mixture of a maleimide compound and a furan compound, and introducing alcohol and isocyanate functional groups, where the alcohol group and the isocyanate group reacts to form the urethane linkages and the furan compound and the maleimide compound react to form the thermally weak Diels-Alder adducts that are incorporated into the backbone of the urethane linkages during the formation of the polyurethane material at temperatures from above room temperature to less than approximately 90.degree. C. The polyurethane material can be easily removed within approximately an hour by heating to temperatures greater than approximately 90.degree. C. in a polar solvent. The polyurethane material can be used in protecting electronic components that may require subsequent removal of the solid material for component repair, modification or quality control.

Loy, Douglas A. (Albuquerque, NM); Wheeler, David R. (Albuquerque, NM); McElhanon, James R. (Livermore, CA); Saunders, Randall S. (late of Albuquerque, NM); Durbin-Voss, Marvie Lou (Albuquerque, NM)

2002-01-01T23:59:59.000Z

162

Technetium Removal Using Tc-Goethite Coprecipitation  

SciTech Connect (OSTI)

This report describes the results from laboratory tests performed at Pacific Northwest National Laboratory for the U.S. Department of Energy (DOE) EM-31 Support Program (EMSP) subtask, “Low temperature waste forms coupled with technetium removal using an alternative immobilization process such as Fe(II) treated-goethite precipitation” to increase our understanding of 99Tc long-term stability in goethite mineral form and the process that controls the 99Tc(VII) reduction and removal by the final Fe (oxy)hydroxide forms. The overall objectives of this task were to 1) evaluate the transformation process of Fe (oxy)hydroxide solids to the more crystalline goethite (?-FeOOH) mineral for 99Tc removal and 2) determine the mechanism that limits 99Tc(IV) reoxidation in Fe(II)-treated 99Tc-goethite mineral and 3) evaluate whether there is a long-term 99Tcoxidation state change for Tc sequestered in the iron solids.

Um, Wooyong; Wang, Guohui; Jung, Hun Bok; Peterson, Reid A.

2013-11-18T23:59:59.000Z

163

Plant community composition and vegetation height, Barrow, Alaska, Ver. 1  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

This dataset contains i) the results of field surveys of plant community composition and vegetation height made between 17th and 29th July 2012 in 48, 1 x 1 m plots located in areas A-D of Intensive Site 1 at the Next-Generation Ecosystem Experiments (NGEE) Arctic site near Barrow, Alaska and ii) results of a mapping exercise undertaken in August 2013 using two perpendicular transects across each polygon containing vegetation plots to determine the boundaries of vegetation communities described in 2012.

Sloan, Victoria; Norby, Richard; Siegrist, Julia; Iversen, Colleen; Brooks, Jonathan; Liebig, Jennifer; Wood, Sarah

164

Plant community composition and vegetation height, Barrow, Alaska, Ver. 1  

SciTech Connect (OSTI)

This dataset contains i) the results of field surveys of plant community composition and vegetation height made between 17th and 29th July 2012 in 48, 1 x 1 m plots located in areas A-D of Intensive Site 1 at the Next-Generation Ecosystem Experiments (NGEE) Arctic site near Barrow, Alaska and ii) results of a mapping exercise undertaken in August 2013 using two perpendicular transects across each polygon containing vegetation plots to determine the boundaries of vegetation communities described in 2012.

Sloan, Victoria; Norby, Richard; Siegrist, Julia; Iversen, Colleen; Brooks, Jonathan; Liebig, Jennifer; Wood, Sarah

2014-04-25T23:59:59.000Z

165

Heat treatment of exchangers to remove coke  

SciTech Connect (OSTI)

This patent describes a process for preparing furfural coke for removal from metallic surfaces. It comprises: heating the furfural coke without causing an evolution of heat capable of undesirably altering metallurgical properties of the surfaces in the presence of a gas containing molecular oxygen at a sufficient temperature below 800{degrees}F (427{degrees}C) for a sufficient time to change the crush strength of the coke so as to permit removal with a water jet at a pressure of five thousand pounds per square inch.

Turner, J.D.

1990-02-20T23:59:59.000Z

166

Integrated pollutant removal: modeling and experimentation  

SciTech Connect (OSTI)

Experimental and computational work at the Albany Research Center, USDOE is investigating an integrated pollutant removal (IPR) process which removes all pollutants from flue gas, including SOX, NOX, particulates, CO2, and Hg. In combination with flue gas recirculation, heat recovery, and oxy-fuel combustion, the process produces solid, gas, and liquid waste streams. The gas exhaust stream comprises O2 and N2. Liquid streams contain H2O, SOX, NOX, and CO2. Computer modeling and low to moderate pressure experimentation are defining system chemistry with respect to SOX and H2O as well as heat and mass transfer for the IPR process.

Ochs, Thomas L.; Oryshchyn, Danylo B.; Summers, Cathy A.

2005-01-01T23:59:59.000Z

167

Process for removing metals from water  

DOE Patents [OSTI]

A process for removing metals from water including the steps of prefiltering solids from the water, adjusting the pH to between about 2 and 3, reducing the amount of dissolved oxygen in the water, increasing the pH to between about 6 and 8, adding water-soluble sulfide to precipitate insoluble sulfide- and hydroxide-forming metals, adding a containing floc, and postfiltering the resultant solution. The postfiltered solution may optionally be eluted through an ion exchange resin to remove residual metal ions. 2 tabs.

Napier, J.M.; Hancher, C.M.; Hackett, G.D.

1987-06-29T23:59:59.000Z

168

fruits and vegetables. Beyond tasting and learning about the many varieties of tomatoes, visitors are also  

E-Print Network [OSTI]

fruits and vegetables. Beyond tasting and learning about the many varieties of tomatoes, visitors and other fruit, vegetable, and herb variety research conducted by Rutgers New Jersey Agricultural

169

E-Print Network 3.0 - amazonian vegetation coupled Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

in Amazonia L. R. Hutyra,1,2 Summary: and resilience of Amazonian vegetation to climate change by analyzing observed climate-vegetation relationships... coupled changes...

170

FULL-SCALE TREATMENT WETLANDS FOR METAL REMOVAL FROM INDUSTRIAL WASTEWATER  

SciTech Connect (OSTI)

The A-01 NPDES outfall at the Savannah River Site receives process wastewater discharges and stormwater runoff from the Savannah River National Laboratory. Routine monitoring indicated that copper concentrations were regularly higher than discharge permit limit, and water routinely failed toxicity tests. These conditions necessitated treatment of nearly one million gallons of water per day plus storm runoff. Washington Savannah River Company personnel explored options to bring process and runoff waters into compliance with the permit conditions, including source reduction, engineering solutions, and biological solutions. A conceptual design for a constructed wetland treatment system (WTS) was developed and the full-scale system was constructed and began operation in 2000. The overall objective of our research is to better understand the mechanisms of operation of the A-01 WTS in order to provide better input to design of future systems. The system is a vegetated surface flow wetland with a hydraulic retention time of approximately 48 hours. Copper, mercury, and lead removal efficiencies are very high, all in excess of 80% removal from water passing through the wetland system. Zinc removal is 60%, and nickel is generally unaffected. Dissolved organic carbon in the water column is increased by the system and reduces toxicity of the effluent. Concentrations of metals in the A-01 WTS sediments generally decrease with depth and along the flow path through the wetland. Sequential extraction results indicate that most metals are tightly bound to wetland sediments.

Nelson, E; John Gladden, J

2007-03-22T23:59:59.000Z

171

Flow and Transport in Regions with Aquatic Vegetation  

E-Print Network [OSTI]

This review describes mean and turbulent flow and mass transport in the presence of aquatic vegetation. Within emergent canopies, the turbulent length scales are set by the stem diameter and spacing, and the mean flow is ...

Nepf, Heidi

172

Status of Baseline Sampling for Elements in Soil and Vegetation...  

Open Energy Info (EERE)

Sampling for Elements in Soil and Vegetation at Four Kgra's in the Imperial Valley, California Jump to: navigation, search OpenEI Reference LibraryAdd to library Journal Article:...

173

Flow-induced reconfiguration of buoyant and flexible aquatic vegetation  

E-Print Network [OSTI]

Plant posture can play a key role in the health of aquatic vegetation, by setting drag, controlling light availability, and mediating the exchange of nutrients and oxygen. We study the flow-induced reconfiguration of ...

Nepf, Heidi

174

Biogeochemistry and vegetation in a cranberry bog chronosequence Genevieve Noyce  

E-Print Network [OSTI]

Biogeochemistry and vegetation in a cranberry bog chronosequence Genevieve Noyce Mount Holyoke Ecosystems Center, MBL, Woods Hole, MA 17 December 2007 #12;Noyce 2 Abstract Abandoned cranberry bogs: abandoned cranberry bogs, succession, biogeochemical controls, exotic species, forests Introduction

Vallino, Joseph J.

175

EIS-0097: Bonneville Power Administration Transmission Facilities Vegetation Management Program  

Broader source: Energy.gov [DOE]

The U.S. Department of Energy’s Bonneville Power Administration prepared this statement to assess the potential environmental and socioeconomic implications of various alternatives associated with implementing a vegetation management program.

176

Investigation of Soil Moisture - Vegetation Interactions in Oklahoma  

E-Print Network [OSTI]

, but not well understood climate factor. This study examines soil moisture-vegetation health interactions using both in situ observations and land surface model simulations. For the observational study, soil moisture is taken from 20 in situ Oklahoma Mesonet...

Ford, Trenton W.

2013-03-06T23:59:59.000Z

177

Carbon Dioxide Emissions From Vegetation-Kill Zones Around The...  

Open Energy Info (EERE)

Usa Abstract A survey of diffuse CO2 efflux, soil temperature and soil-gas chemistry over areas of localized vegetation-kill on and around the resurgent dome of Long...

178

Carbon Dioxide Emissions From Vegetation-Kill Zones Around The...  

Open Energy Info (EERE)

USA Abstract A survey of diffuse CO2 efflux, soil temperature and soil-gas chemistry over areas of localized vegetation-kill on and around the resurgent dome of Long...

179

Drag, turbulence, and diffusion in flow through emergent vegetation  

E-Print Network [OSTI]

Aquatic plants convert mean kinetic energy into turbulent kinetic energy at the scale of the plant stems and branches. This energy transfer, linked to wake generation, affects vegetative drag and turbulence intensity. ...

Nepf, Heidi

180

Further Tests of Vegetable Varieties for the Winter Garden Region.  

E-Print Network [OSTI]

Watermelon 3 8 Summary of Promising Varieties 42 AcknowIedgments Literature Cited BULLETIN NO. 546 JULY , 1937 FURTHER TESTS OF VEGETABLE VARIETIES FOR THE WINTER GARDEN REGION By Leslie R. Hawthorn, Horticulturist, Substation No. 19, Winter Haven...

Hawthorn, L. R. (Leslie Rushton)

1937-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Pentek metal coating removal system: Baseline report  

SciTech Connect (OSTI)

The Pentek coating removal technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The Pentek coating removal system consisted of the ROTO-PEEN Scaler, CORNER-CUTTER{reg_sign}, and VAC-PAC{reg_sign}. They are designed to remove coatings from steel, concrete, brick, and wood. The Scaler uses 3M Roto Peen tungsten carbide cutters while the CORNER-CUTTER{reg_sign} uses solid needles for descaling activities. These hand tools are used with the VAC-PAC{reg_sign} vacuum system to capture dust and debris as removal of the coating takes place. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. Dust exposure minimal, but noise exposure was significant. Further testing for each exposure is recommended because of the environment where the testing demonstration took place. It is feasible that the dust and noise levels will be higher in an enclosed operating environment of different construction. In addition, other areas of concern found were arm-hand vibration, whole-body, ergonomics, heat stress, tripping hazards, electrical hazards, machine guarding, and lockout/tagout.

NONE

1997-07-31T23:59:59.000Z

182

Method of preparation of removable syntactic foam  

DOE Patents [OSTI]

Easily removable, environmentally safe, low-density, syntactic foams are disclosed which are prepared by mixing insoluble microballoons with a solution of water and/or alcohol-soluble polymer to produce a pourable slurry, optionally vacuum filtering the slurry in varying degrees to remove unwanted solvent and solute polymer, and drying to remove residual solvent. The properties of the foams can be controlled by the concentration and physical properties of the polymer, and by the size and properties of the microballoons. The suggested solute polymers are non-toxic and soluble in environmentally safe solvents such as water or low-molecular weight alcohols. The syntactic foams produced by this process are particularly useful in those applications where ease of removability is beneficial, and could find use in packaging recoverable electronic components, in drilling and mining applications, in building trades, in art works, in the entertainment industry for special effects, in manufacturing as temporary fixtures, in agriculture as temporary supports and containers and for delivery of fertilizer, in medicine as casts and splints, as temporary thermal barriers, as temporary protective covers for fragile objects, as filters for particulate matter, which matter may be easily recovered upon exposure to a solvent, as in-situ valves (for one-time use) which go from maximum to minimum impedance when solvent flows through, and for the automatic opening or closing of spring-loaded, mechanical switches upon exposure to a solvent, among other applications. 1 fig.

Arnold, C. Jr.; Derzon, D.K.; Nelson, J.S.; Rand, P.B.

1995-07-11T23:59:59.000Z

183

Automatic Red Eye Removal for Digital Photography  

E-Print Network [OSTI]

Chapter 1 Automatic Red Eye Removal for Digital Photography FRANCESCA GASPARINI DISCo, Dipartimento The red eye effect is a well known problem in photography. It is often seen in amateur shots taken with a built-in flash, but the problem is also well known to professional photographers. Red eye is the red

Schettini, Raimondo

184

Plastic bottles > Remove lids (not recyclable)  

E-Print Network [OSTI]

Plastic bottles Please: > Remove lids (not recyclable) > Empty bottles > Rinse milk bottles, & other bottles if possible > Squash bottles www.st-andrews.ac.uk/estates/environment All types of plastic bottle accepted Clear, opaque and coloured bottles Labels can remain on X No plastic bags X No plastics

Brierley, Andrew

185

Method of preparation of removable syntactic foam  

DOE Patents [OSTI]

Easily removable, environmentally safe, low-density, syntactic foams are disclosed which are prepared by mixing insoluble microballoons with a solution of water and/or alcohol-soluble polymer to produce a pourable slurry, optionally vacuum filtering the slurry in varying degrees to remove unwanted solvent and solute polymer, and drying to remove residual solvent. The properties of the foams can be controlled by the concentration and physical properties of the polymer, and by the size and properties of the microballoons. The suggested solute polymers are non-toxic and soluble in environmentally safe solvents such as water or low-molecular weight alcohols. The syntactic foams produced by this process are particularly useful in those applications where ease of removability is beneficial, and could find use in packaging recoverable electronic components, in drilling and mining applications, in building trades, in art works, in the entertainment industry for special effects, in manufacturing as temporary fixtures, in agriculture as temporary supports and containers and for delivery of fertilizer, in medicine as casts and splints, as temporary thermal barriers, as temporary protective covers for fragile objects, as filters for particulate matter, which matter may be easily recovered upon exposure to a solvent, as in-situ valves (for one-time use) which go from maximum to minimum impedance when solvent flows through, and for the automatic opening or closing of spring-loaded, mechanical switches upon exposure to a solvent, among other applications.

Arnold, Jr., Charles (Albuquerque, NM); Derzon, Dora K. (Albuquerque, NM); Nelson, Jill S. (Albuquerque, NM); Rand, Peter B. (Albuquerque, NM)

1995-01-01T23:59:59.000Z

186

Method for Removing Precipitates in Biofuel  

Energy Innovation Portal (Marketing Summaries) [EERE]

At ORNL the application of ultrasonic energy, or sonication, has been shown to successfully remove or prevent the formation of 50–90% of the precipitates in biofuels. Precipitates can plug filters as biodiesel is transported from one location to another, and often cannot be detected by visual inspection....

2010-12-08T23:59:59.000Z

187

Method of removing cesium from steam  

DOE Patents [OSTI]

Method for removal of radioactive cesium from a hot vapor, such as high temperature steam, including the steps of passing input hot vapor containing radioactive cesium into a bed of silicate glass particles and chemically incorporating radioactive cesium in the silicate glass particles at a temperature of at least about 700.degree. F.

Carson, Jr., Neill J. (Clarendon Hills, IL); Noland, Robert A. (Oak Park, IL); Ruther, Westly E. (Skokie, IL)

1991-01-01T23:59:59.000Z

188

Removal of a Permanent IVC Filter  

SciTech Connect (OSTI)

Inferior vena cava (IVC) filters are increasingly used for prevention of life-threatening pulmonary emboli in patients who have contraindications to anticoagulation therapy. We report a case of the removal of a permanent IVC filter, which was inadvertently inserted due to an incorrect ultrasound report.

Kumar, Bangalore C. Anil [Queen's Medical Centre, Department of Radiology (United Kingdom)], E-mail: anil.kumar@doctors.org.uk; Chakraverty, Sam; Zealley, Ian [Ninewells Hospital, Department of Radiology (United Kingdom)

2006-02-15T23:59:59.000Z

189

Map of mixed prairie grassland vegetation, Rocky Flats, Colorado  

SciTech Connect (OSTI)

A color vegetation map at the scale of 1:12,000 of the area surrounding the Rocky Flats, Rockwell International Plant near Boulder, Colorado, provides a permanent record of baseline data which can be used to monitor changes in both vegetation and environment and thus to contribute to future land management and land-use policies. Sixteen mapping units based on species composition were identified, and characterized by two 10-m/sup 2/ vegetation stands each. These were grouped into prairie, pasture, and valley side on the basis of their species composition. Both the mapping units and these major groups were later confirmed by agglomerative clustering analysis of the 32 vegetation stands on the basis of species composition. A modified Bray and Curtis ordination was used to determine the environmental factor complexes controlling the distribution of vegetation at Rocky flats. Recommendations are made for future policies of environmental management and predictions of the response to environmental change of the present vegetation at the Rocky Flats site.

Clark, S J.V.; Webber, P J; Komarkova, V; Weber, W A

1980-01-01T23:59:59.000Z

190

Uncertainty analysis of vegetation distribution in the northern high latitudes during the 21st century with a dynamic vegetation model  

E-Print Network [OSTI]

This study aims to assess how high-latitude vegetation may respond under various climate scenarios during the 21st century with a focus on analyzing model parameters induced uncertainty and how this uncertainty compares ...

Jiang, Yueyang

191

How to Remove Tangles in Your DNA  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation ProposedUsingFun withconfinement plasmas inPortalAllBPA addressesHow You Overview

192

Vegetation's Red Edge: A Possible Spectroscopic Biosignature of Extraterrestrial Plants  

E-Print Network [OSTI]

Earth's deciduous plants have a sharp order-of-magnitude increase in leaf reflectance between approximately 700 and 750 nm wavelength. This strong reflectance of Earth's vegetation suggests that surface biosignatures with sharp spectral features might be detectable in the spectrum of scattered light from a spatially unresolved extrasolar terrestrial planet. We assess the potential of Earth's step-function-like spectroscopic feature, referred to as the "red edge", as a tool for astrobiology. We review the basic characteristics and physical origin of the red edge and summarize its use in astronomy: early spectroscopic efforts to search for vegetation on Mars and recent reports of detection of the red edge in the spectrum of Earthshine (i.e., the spatially integrated scattered light spectrum of Earth). We present Earthshine observations from Apache Point Observatory to emphasize that time variability is key to detecting weak surface biosignatures such as the vegetation red edge. We briefly discuss the evolutionary advantages of vegetation's red edge reflectance, and speculate that while extraterrestrial "light harvesting organisms" have no compelling reason to display the exact same red edge feature as terrestrial vegetation, they might have similar spectroscopic features at different wavelengths than terrestrial vegetation. This implies that future terrestrial-planet-characterizing space missions should obtain data that allow time-varying, sharp spectral features at unknown wavelengths to be identified. We caution that some mineral reflectance edges are similar in slope and strength to vegetation's red edge (albeit at different wavelengths); if an extrasolar planet reflectance edge is detected care must be taken with its interpretation.

Sara Seager; Edwin L. Turner; Justin Schafer; Eric B. Ford

2005-03-14T23:59:59.000Z

193

Removal of fluoride from aqueous nitric acid  

SciTech Connect (OSTI)

Several methods for removing fluoride from aqueous nitric acid were investigated and compared with the frequently used aluminum nitrate-calcium nitrate (Ca/sup 2 +/-Al/sup 3 +/) chemical trap-distillation system. Zirconium oxynitrate solutions were found to be superior in preventing volatilization of fluoride during distillation of the nitric acid, producing decontamination factors (DFs) on the order of 2 x 10/sup 3/ (vs approx. 500 for the Ca/sup 2 +/-Al/sup 3 +/ system). Several other metal nitrate systems were tested, but they were less effective. Alumina and zirconia columns proved highly effective in removing HF from HF-HNO/sub 3/ vapors distilled through the columns; fluoride DFs on the order of 10/sup 6/ and 10/sup 4/, respectively, were obtained. A silica gel column was very effective in adsorbing HF from HF-HNO/sub 3/ solutions, producing a fluoride DF of approx. 10/sup 4/.

Pruett, D.J.; Howerton, W.B.; Mailen, J.C.

1981-06-01T23:59:59.000Z

194

Photoacoustic removal of occlusions from blood vessels  

DOE Patents [OSTI]

Partial or total occlusions of fluid passages within the human body are removed by positioning an array of optical fibers in the passage and directing treatment radiation pulses along the fibers, one at a time, to generate a shock wave and hydrodynamics flows that strike and emulsify the occlusions. A preferred application is the removal of blood clots (thrombin and embolic) from small cerebral vessels to reverse the effects of an ischemic stroke. The operating parameters and techniques are chosen to minimize the amount of heating of the fragile cerebral vessel walls occurring during this photo acoustic treatment. One such technique is the optical monitoring of the existence of hydrodynamics flow generating vapor bubbles when they are expected to occur and stopping the heat generating pulses propagated along an optical fiber that is not generating such bubbles.

Visuri, Steven R. (Livermore, CA); Da Silva, Luiz B. (Danville, CA); Celliers, Peter M. (Berkeley, CA); London, Richard A. (Orinda, CA); Maitland, IV, Duncan J. (Lafayette, CA); Esch, Victor C. (San Francisco, CA)

2002-01-01T23:59:59.000Z

195

Fly ash enhanced metal removal process  

SciTech Connect (OSTI)

The primary objective of the study was to evaluate the effectiveness of fly ashes from local thermal power plants in the removal of cadmium, nickel, chromium, lead, and copper from aqueous waste streams. Physical and chemical characteristics of fly ashes were determined, batch isotherm studies were conducted. A practical application of using fly ash in treating spent electroless nickel (EN) plating baths by modified conventional precipitation or solid enhanced metal removal process (SEMR) was investigated. In addition to nickel the EN baths also contains completing agents such as ammonium citrate and succinic acid reducing agents such as phosphate and hypophosphite. SEMR experiments were conducted at different pHs, fly ash type and concentrations, and settling times.

Nonavinakere, S. [Plexus Scientific Corp., Annapolis, MD (United States); Reed, B.E. [West Virginia Univ., Morgantown, WV (United States). Dept. of Civil Engineering

1995-12-31T23:59:59.000Z

196

Method of arsenic removal from water  

DOE Patents [OSTI]

A method for low-cost arsenic removal from drinking water using chemically prepared bottom ash pre-treated with ferrous sulfate and then sodium hydroxide. Deposits on the surface of particles of bottom ash form of activated iron adsorbent with a high affinity for arsenic. In laboratory tests, a miniscule 5 grams of pre-treated bottom ash was sufficient to remove the arsenic from 2 liters of 2400 ppb (parts per billion) arsenic-laden water to a level below 50 ppb (the present United States Environmental Protection Agency limit). By increasing the amount of pre-treated bottom ash, even lower levels of post-treatment arsenic are expected. It is further expected that this invention supplies a very low-cost solution to arsenic poisoning for large population segments.

Gadgil, Ashok (El Cerrito, CA)

2010-10-26T23:59:59.000Z

197

IMPROVED PROCESSES TO REMOVE NAPHTHENIC ACIDS  

SciTech Connect (OSTI)

In the second year of this project, we continued our effort to develop low temperature decarboxylation catalysts and investigate the behavior of these catalysts at different reaction conditions. We conducted a large number of dynamic measurements with crude oil and model compounds to obtain the information at different reaction stages, which was scheduled as the Task2 in our work plan. We developed a novel adsorption method to remove naphthenic acid from crude oil using naturally occurring materials such as clays. Our results show promise as an industrial application. The theoretical modeling proposed several possible reaction pathways and predicted the reactivity depending on the catalysts employed. From all of these studies, we obtained more comprehensive understanding about catalytic decarboxylation and oil upgrading based on the naphthenic acid removal concept.

Aihua Zhang; Qisheng Ma; Kangshi Wang, William A. Goddard, Yongchun Tang

2005-05-05T23:59:59.000Z

198

Removal of arsenic compounds from petroliferous liquids  

DOE Patents [OSTI]

Described is a process for removing arsenic from petroliferous derived liquids by contacting said liquid at an elevated temperature with a divinylbenzene-crosslinked polystyrene having catechol ligands anchored thereon. Also, described is a process for regenerating spent catecholated polystyrene by removal of the arsenic bound to it from contacting petroliferous liquid as described above and involves: a. treating said spent catecholated polystyrene, at a temperature in the range of about 20.degree. to 100.degree. C. with an aqueous solution of at least one carbonate and/or bicarbonate of ammonium, alkali and alkaline earth metals, said solution having a pH between about 8 and 10 and, b. separating the solids and liquids from each other. Preferably the regeneration treatment is in two steps wherein step (a) is carried out with an aqueous alcoholic carbonate solution containing lower alkyl alcohol, and, steps (a) and (b) are repeated using a bicarbonate.

Fish, Richard H. (Berkeley, CA)

1985-01-01T23:59:59.000Z

199

Acid treatment removes zinc sulfide scale restriction  

SciTech Connect (OSTI)

This paper reports that removal of zinc sulfide (ZnS) scale with acid restored an offshore Louisiana well's production to original rates. The zinc sulfide scale was determined to be in the near well bore area. The selected acid had been proven to control iron sulfide (FeS) scales in sour wells without causing harm to surface production equipment, tubing, and other downhole hardware. The successful removal of the blockage re-established previous production rates with a 105% increase in flowing tubing pressure. On production for a number of months, a high rate, high-pressure offshore well was experiencing unusually rapid pressure and rate declines. A small sample of the restrictive material was obtained during the wire line operations. The well was subsequently shut in while a laboratory analysis determined that zinc sulfide was the major component of the obstruction.

Biggs, K. (Kerr McGee Corp., Lafayette, LA (US)); Allison, D. (Otis Engineering Corp., Lafayette, LA (US)); Ford, W.G.F. (Halliburton Co., Duncan, OK (United States))

1992-08-31T23:59:59.000Z

200

TMI defueling project fuel debris removal system  

SciTech Connect (OSTI)

The three mile Island Unit 2 (TMI-2) pressurized water reactor loss-of-coolant accident on March 28, 1979, presented the nuclear community with many challenging remediation problems; most importantly, the removal of the fission products within the reactor containment vessel. To meet this removal problem, an air-lift system (ALS) can be used to employ compressed air to produce the motive force for transporting debris. Debris is separated from the transport stream by gravity separation. The entire method does not rely on any moving parts. Full-scale testing of the ALS at the Idaho National Engineering Laboratory (INEL) has demonstrated the capability of transporting fuel debris from beneath the LCSA into a standard fuel debris bucket at a minimum rate of 230 kg/min.

Burdge, B.

1992-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

TMI defueling project fuel debris removal system  

SciTech Connect (OSTI)

The three mile Island Unit 2 (TMI-2) pressurized water reactor loss-of-coolant accident on March 28, 1979, presented the nuclear community with many challenging remediation problems; most importantly, the removal of the fission products within the reactor containment vessel. To meet this removal problem, an air-lift system (ALS) can be used to employ compressed air to produce the motive force for transporting debris. Debris is separated from the transport stream by gravity separation. The entire method does not rely on any moving parts. Full-scale testing of the ALS at the Idaho National Engineering Laboratory (INEL) has demonstrated the capability of transporting fuel debris from beneath the LCSA into a standard fuel debris bucket at a minimum rate of 230 kg/min.

Burdge, B.

1992-08-01T23:59:59.000Z

202

Influence of metal process micronic and submicronic particles on vegetables quality and ecosystems.  

E-Print Network [OSTI]

sativa) and parsley (Petroselinum crispum), vegetables currently cultivated in kitchen gardens with high

Paris-Sud XI, Université de

203

Advection, dispersion, and filtration of fine particles within emergent vegetation of the Florida Everglades  

E-Print Network [OSTI]

.g., phosphorous) [Sansalone and Buchberger, 1997; Noe et al., 2007]. [3] Wetland vegetation influences flow

204

Vegetation responses in Alaskan arctic tundra after 8 years of a summer warming and winter snow  

E-Print Network [OSTI]

by insulating vegetation from winter wind and temperature extremes, modifying winter soil temperatures

Ickert-Bond, Steffi

205

Process for removing sulfur from coal  

DOE Patents [OSTI]

A process is disclosed for the removal of divalent organic and inorganic sulfur compounds from coal and other carbonaceous material. A slurry of pulverized carbonaceous material is contacted with an electrophilic oxidant which selectively oxidizes the divalent organic and inorganic compounds to trivalent and tetravalent compounds. The carbonaceous material is then contacted with a molten caustic which dissolves the oxidized sulfur compounds away from the hydrocarbon matrix.

Aida, T.; Squires, T.G.; Venier, C.G.

1983-08-11T23:59:59.000Z

206

REMOVAL OF LEGACY PLUTONIUM MATERIALS FROM SWEDEN  

SciTech Connect (OSTI)

U.S. Department of Energy’s National Nuclear Security Administration (NNSA) Office of Global Threat Reduction (GTRI) recently removed legacy plutonium materials from Sweden in collaboration with AB SVAFO, Sweden. This paper details the activities undertaken through the U.S. receiving site (Savannah River Site (SRS)) to support the characterization, stabilization, packaging and removal of legacy plutonium materials from Sweden in 2012. This effort was undertaken as part of GTRI’s Gap Materials Program and culminated with the successful removal of plutonium from Sweden as announced at the 2012 Nuclear Security Summit. The removal and shipment of plutonium materials to the United States was the first of its kind under NNSA’s Global Threat Reduction Initiative. The Environmental Assessment for the U.S. receipt of gap plutonium material was approved in May 2010. Since then, the multi-year process yielded many first time accomplishments associated with plutonium packaging and transport activities including the application of the of DOE-STD-3013 stabilization requirements to treat plutonium materials outside the U.S., the development of an acceptance criteria for receipt of plutonium from a foreign country, the development and application of a versatile process flow sheet for the packaging of legacy plutonium materials, the identification of a plutonium container configuration, the first international certificate validation of the 9975 shipping package and the first intercontinental shipment using the 9975 shipping package. This paper will detail the technical considerations in developing the packaging process flow sheet, defining the key elements of the flow sheet and its implementation, determining the criteria used in the selection of the transport package, developing the technical basis for the package certificate amendment and the reviews with multiple licensing authorities and most importantly integrating the technical activities with the Swedish partners.

Dunn, Kerry A. [Savannah River National Laboratory; Bellamy, J. Steve [Savannah River National Laboratory; Chandler, Greg T. [Savannah River National Laboratory; Iyer, Natraj C. [U.S. Department of Energy, National Nuclear Security Administration, Office of; Koenig, Rich E.; Leduc, D. [Savannah River National Laboratory; Hackney, B. [Savannah River National Laboratory; Leduc, Dan R. [Savannah River National Laboratory

2013-08-18T23:59:59.000Z

207

Removal of copper from ferrous scrap  

DOE Patents [OSTI]

A process for removing copper from ferrous or other metal scrap in which the scrap is contacted with a polyvalent metal sulfide slag in the presence of an excess of copper-sulfide forming additive to convert the copper to copper sulfide which is extracted into the slag to provide a ratio of copper in the slag to copper in the metal scrap of at least about 10.

Blander, M.; Sinha, S.N.

1987-07-30T23:59:59.000Z

208

Removal of copper from ferrous scrap  

DOE Patents [OSTI]

A process for removing copper from ferrous or other metal scrap in which the scrap is contacted with a polyvalent metal sulfide slag in the presence of an excess of copper-sulfide forming additive to convert the copper to copper sulfide which is extracted into the slag to provide a ratio of copper in the slag to copper in the metal scrap of at least about 10.

Blander, M.; Sinha, S.N.

1990-05-15T23:59:59.000Z

209

Removal of copper from ferrous scrap  

DOE Patents [OSTI]

A process for removing copper from ferrous or other metal scrap in which the scrap is contacted with a polyvalent metal sulfide slag in the presence of an excess of copper-sulfide forming additive to convert the copper to copper sulfide which is extracted into the slag to provide a ratio of copper in the slag to copper in the metal scrap of at least about 10.

Blander, Milton (12833 S. 82nd Ct., Palos Park, IL 60464); Sinha, Shome N. (5748 Drexel, 2A, Chicago, IL 60637)

1990-01-01T23:59:59.000Z

210

Process for removing mercury from aqueous solutions  

DOE Patents [OSTI]

A process for removing mercury from water to a level not greater than two parts per billion wherein an anion exchange material that is insoluble in water is contacted first with a sulfide containing compound and second with a compound containing a bivalent metal ion forming an insoluble metal sulfide. To this treated exchange material is contacted water containing mercury. The water containing not more than two parts per billion of mercury is separated from the exchange material.

Googin, J.M.; Napier, J.M.; Makarewicz, M.A.; Meredith, P.F.

1985-03-04T23:59:59.000Z

211

Process for removing mercury from aqueous solutions  

DOE Patents [OSTI]

A process for removing mercury from water to a level not greater than two parts per billion wherein an anion exchange material that is insoluble in water is contacted first with a sulfide containing compound and second with a compound containing a bivalent metal ion forming an insoluble metal sulfide. To this treated exchange material is contacted water containing mercury. The water containing not more than two parts per billion of mercury is separated from the exchange material.

Googin, John M. (Oak Ridge, TN); Napier, John M. (Oak Ridge, TN); Makarewicz, Mark A. (Knoxville, TN); Meredith, Paul F. (Knoxville, TN)

1986-01-01T23:59:59.000Z

212

EFFECTS OF VEGETATION ON TURBULENCE, SEDIMENT TRANSPORT AND STREAM MORPHOLOGY  

SciTech Connect (OSTI)

Vegetation, from an individual stem to multiple stems in various configurations, profoundly alters turbulent flows. These alterations influence sediment transport and stream morphology, but depend on complex interactions and relationships between flow, plants and sediment properties. This is illustrated for three case studies that represent a variety of macrophyte patterns and scales in the environment: flows through simulated uniformly distributed plant stems, emergent and submerged; flows with alternating simulated stem patches; and flow around an isolated stem in a flood plain. The emergent case demonstrates that when density is sparse the mean velocity and turbulence intensities vary horizontally around the stems, which would promote a heterogeneous bedform morphology. However, it is still unclear how density, submergence ratio, and flow Reynolds number, in combination, influence interference effects, vortex shedding and dissipation, and velocity, pressure and lift fluctuations that affect sediment entrainment. The submerged case demonstrates significant reduction of the mean velocity, turbulence intensities, and turbulent shear near the bed compared to an unobstructed flow and supports numerous observations that vegetation promotes deposition or stabilizes bed sediments. The case of alternating emergent vegetation patches illustrates how vegetation adjusts the bed promoting scour in open water and deposition within the patches. The isolated stem case illustrates the variety of coherent structures generated, their complex interaction, and their role in specific sediment transport phenomena observed. Additional research is required, however, to quantify thresholds and relationships for flow-vegetation-sediment interactions so that aquatic macrophyte plantings can be used more effectively in water resource management.

Neary, Vincent S [ORNL

2012-01-01T23:59:59.000Z

213

CX-011651: Categorical Exclusion Determination | Department of...  

Broader source: Energy.gov (indexed) [DOE]

Exclusion Determination CX-011651: Categorical Exclusion Determination Hazard Tree Removal Along the Prescott Peacock 230 Kilovolt Transmission Line CX(s) Applied: B1.3...

214

CX-009114: Categorical Exclusion Determination | Department of...  

Broader source: Energy.gov (indexed) [DOE]

CX-009114: Categorical Exclusion Determination Dismantle and Remove Area Radiation Monitors (General) CX(s) Applied: B3.1 Date: 08232012 Location(s): South Carolina...

215

CX-007162: Categorical Exclusion Determination | Department of...  

Broader source: Energy.gov (indexed) [DOE]

CX-007162: Categorical Exclusion Determination Pinnacle Peak Substation Electrical Equipment Removal CX(s) Applied: B1.17 Date: 05092011 Location(s): Maricopa...

216

CX-008729: Categorical Exclusion Determination | Department of...  

Broader source: Energy.gov (indexed) [DOE]

729: Categorical Exclusion Determination CX-008729: Categorical Exclusion Determination Reverse Osmosis System Removal CX(s) Applied: B1.26 Date: 06252012 Location(s): Idaho...

217

CX-003037: Categorical Exclusion Determination | Department of...  

Broader source: Energy.gov (indexed) [DOE]

Determination CX-003037: Categorical Exclusion Determination Mercury Removal from Clean Coal Processing Air Stream CX(s) Applied: B3.6 Date: 07132010 Location(s): Butte,...

218

CX-005547: Categorical Exclusion Determination | Department of...  

Broader source: Energy.gov (indexed) [DOE]

Exclusion Determination Specific Manufacturing Capability (SMC) Incinerator and Propane Tank System Removal CX(s) Applied: B1.23 Date: 03222011 Location(s): Idaho...

219

Novel Bioplastics and biocomposites from Vegetable Oils  

SciTech Connect (OSTI)

Polymeric materials have been prevalent in our everyday lives for quite a long time. Most of today's polymeric materials are derived from nonrenewable petroleum-based feedstocks. Instabilities in the regions where petroleum is drilled, along with an increased demand in petroleum, have driven the price of crude oil to record high prices. This, in effect, increases the price of petroleum-based polymeric materials, which has caused a heightened awareness of renewable alternatives for polymeric feedstocks. Cellulose, starch, proteins and natural oils have all been examined as possible polymeric feedstocks. Natural oils are commercially available on a large scale and are relatively cheap. It is projected that the U.S. alone will produce 21 billion pounds of soybean oil in the period 2008/2009. Natural oils also have the advantages of inherent biodegradability, low toxicity, high purity and ready availability. Most natural oils possess a triglyceride structure as shown in Figure 1. Most natural oils have a unique distribution of fatty acid side chains, along with varying degrees of unsaturation per triglyceride. Common fatty acid side chains in naturally occurring oils are palmitic acid (C16:0), a 16 carbon fatty acid with no unsaturation; stearic acid (C18:0), an 18 carbon fatty acid with no unsaturation; oleic acid (C18:1), an 18 carbon fatty acid with one double bond; linoleic acid (C18:2), an 18 carbon fatty acid with two double bonds; and linolenic acid (C18:3), an 18 carbon fatty acid with three double bonds. Of course, there are other fatty acids with varying degrees of unsaturation, but their abundance is usually minimal. All of the unsaturated fatty acids mentioned have naturally occurring cis double bonds, which is common for most unsaturated fatty acids. In addition, the afore mentioned fatty acids have the first double bond at the position of carbon 9 (C9), followed by carbon 12 (C12), if there are two degrees of unsaturation, then at carbon 15 (C15), if there are three degrees of unsaturation. In addition, the double bonds are not in conjugation. Table 1 gives the fatty acid make-up of linseed oil. It can be seen that linseed oil has an average of 6.0 double bonds per triglyceride. Its fatty acid content consists of 5.4% palmitic acid (C16:0), 3.5% stearic acid (C18:0), 19% oleic acid (C18:1), 24 % linoleic acid (C18:2) and 47% linolenic (C18:3). Table 1 also gives the fatty acid composition and varying degrees of unsaturation for various other naturally-occurring natural vegetable oils. The regions of unsaturation in natural oils allow for interesting polymer chemistry to take place. Some of this interesting polymer science, however, involves chemical modification of the regions of unsaturation. Acrylated epoxidized soybean oil (AESO) is prepared by epoxidation of the double bonds, followed by ring opening with acrylic acid. The resulting oil has both acrylate groups and hydroxyl groups. Wool and colleagues have further reacted the hydroxyl groups within the oil with maleic anhydride to produce maleated acrylated epoxidized soybean oil (MAESO). The MAESO has been copolymerized with styrene free radically to produce promising thermosetting sheet molding resins. Petrovi? and co-workers have directly ring opened the epoxidized oil to produce polyols that produce promising polyurethanes through condensation polymerization with diisocyanates. Our group's work initially focused on direct cationic copolymerization of the double bonds or conjugated double bonds of natural oils with monomers, such as styrene and divinylbenzene, to produce promising thermosetting resins. The only modification of the oils that was carried out in these studies was conjugation of the double bonds to enhance the reactivity of the oil. This work has been expanded recently with the incorporation of glass fiber to produce promising composites. We have also explored thermal polymerization techniques to make novel thermosets. This dissertation is divided into four chapters. The first chapter discusses the synthesis and characterization of biobased

Phillip H. Henna

2008-08-18T23:59:59.000Z

220

Process for removing technetium from iron and other metals  

DOE Patents [OSTI]

A process for removing technetium from iron and other metals comprises the steps of converting the molten, alloyed technetium to a sulfide dissolved in manganese sulfide, and removing the sulfide from the molten metal as a slag. 4 figs.

Leitnaker, J.M.; Trowbridge, L.D.

1999-03-23T23:59:59.000Z

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Process for removing technetium from iron and other metals  

DOE Patents [OSTI]

A process for removing technetium from iron and other metals comprises the steps of converting the molten, alloyed technetium to a sulfide dissolved in manganese sulfide, and removing the sulfide from the molten metal as a slag.

Leitnaker, James M. (Kingston, TN); Trowbridge, Lee D. (Oak Ridge, TN)

1999-01-01T23:59:59.000Z

222

Removing nuclear waste, one shipment at a time  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Removing nuclear waste, one shipment at a time Removing nuclear waste, one shipment at a time The Lab's 1,000th shipment of transuranic waste recently left Los Alamos, on its way...

223

Czech Republic HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

HEU Removal Czech Republic HEU Removal Location Czech Republic United States 49 35' 23.3628" N, 15 4' 23.6712" E See map: Google Maps Javascript is required to view this map....

224

United Kingdom HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

HEU Removal United Kingdom HEU Removal Location United Kingdom United States 52 24' 15.1416" N, 1 34' 55.3116" W See map: Google Maps Javascript is required to view this map...

225

Method for removing fluoride contamination from nitric acid  

SciTech Connect (OSTI)

Fluoride ions are removed from nitric acid solution by contacting the vaporized solution with alumina or zirconium.

Howerton, W.B.; Pruett, D.J.

1982-07-13T23:59:59.000Z

226

Ultracapacitor having residual water removed under vacuum  

DOE Patents [OSTI]

A multilayer cell is provided that comprises two solid, nonporous current collectors, two porous electrodes separating the current collectors, a porous separator between the electrodes and an electrolyte occupying pores in the electrodes and separator. The mutilayer cell is electrolyzed to disassociate water within the cell to oxygen gas and hydrogen gas. A vacuum is applied to the cell substantially at the same time as the electrolyzing step, to remove the oxygen gas and hydrogen gas. The cell is then sealed to form a ultracapacitor substantially free from water.

Wei, Chang (Niskayuna, NY); Jerabek, Elihu Calvin (Glenmont, NY); Day, James (Scotia, NY)

2002-10-15T23:59:59.000Z

227

Portsmouth Removal Actions | Department of Energy  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"ClickPipelinesProvedDecemberInitiativesNationalNuclearRockyServicesFindings andRemedial ActionsRemoval

228

TYPE A VERIFICATION FOR THE HIGH FLUX BEAM REACTOR UNDERGROUND UTILITIES REMOVAL PHASE 2 DF WASTE LINE REMOVAL, BNL  

SciTech Connect (OSTI)

5098-SR-02-0 PROJECT-SPECIFIC TYPE A VERIFICATION FOR THE HIGH FLUX BEAM REACTOR UNDERGROUND UTILITIES REMOVAL PHASE 2 DF WASTE LINE REMOVAL, BROOKHAVEN NATIONAL LABORATORY

P.C. Weaver

2010-07-09T23:59:59.000Z

229

Process for removing polychlorinated biphenyls from soil  

DOE Patents [OSTI]

The present invention relates to a method of removing polychlorinated biphenyls from soil. The polychlorinated biphenyls are extracted from the soil by employing a liquid organic solvent dispersed in water in the ratio of about 1:3 to 3:1. The organic solvent includes such materials as short-chain hydrocarbons including kerosene or gasoline which are immiscible with water and are nonpolar. The organic solvent has a greater affinity for the PCB's than the soil so as to extract the PCB's from the soil upon contact. The organic solvent phase is separated from the suspended soil and water phase and distilled for permitting the recycle of the organic solvent phase and the concentration of the PCB's in the remaining organic phase. The present process can be satisfactorily practiced with soil containing 10 to 20% petroleum-based oils and organic fluids such as used in transformers and cutting fluids, coolants and the like which contain PCB's. The subject method provides for the removal of a sufficient concentration of PCB's from the soil to provide the soil with a level of PCB's within the guidelines of the Environmental Protection Agency.

Hancher, C.W.; Saunders, M.B.; Googin, J.M.

1984-11-16T23:59:59.000Z

230

Removal of arsenic compounds from petroliferous liquids  

DOE Patents [OSTI]

The present invention in one aspect comprises a process for removing arsenic from petroliferous-derived liquids by contacting said liquid with a divinylbenzene-crosslinked polystyrene polymer (i.e. PS-DVB) having catechol ligands anchored to said polymer, said contacting being at an elevated temperature. In another aspect, the invention is a process for regenerating spent catecholated polystyrene polymer by removal of the arsenic bound to it from contacting petroliferous liquid in accordance with the aspect described above which regenerating process comprises: (a) treating said spent catecholated polystyrene polymer with an aqueous solution of at least one member selected from the group consisting of carbonates and bicarbonates of ammonium, alkali metals, and alkaline earth metals, said solution having a pH between about 8 and 10, and said treating being at a temperature in the range of about 20/sup 0/ to 100/sup 0/C; (b) separating the solids and liquids from each other. In a preferred embodiment the regeneration treatment is in two steps wherein step: (a) is carried out with an aqueous alcoholic carbonate solution which includes at least one lower alkyl alcohol, and, steps (c) and (d) are added. Steps (c) and (d) comprise: (c) treating the solids with an aqueous alcoholic solution of at least one ammonium, alkali or alkaline earth metal bicarbonate at a temperature in the range of about 20 to 100/sup 0/C; and (d) separating the solids from the liquids.

Fish, R.H.

1984-04-06T23:59:59.000Z

231

Tailoring hydrocarbon streams for asphaltene removal  

SciTech Connect (OSTI)

Oilfield production is often hindered by asphaltene precipitation which tends to fill the pores of the reservoir rocks and plug the wellbore tubing as well as the other auxiliary equipment used during crude oil recovery. Several remedies to remove these deposits have been proposed and patented but the injection of aromatic solvents such as toluene and light petroleum distillates is normally preferred. Previous studies with a number of pure aromatic hydrocarbons have shown that the solvent capacity of these molecules may be very different and that the degree of condensation plays an important role. In this regard, tetralins and naphthalenes are superior to alkylbenzenes. However, because the use of pure compounds is not economically feasible, the authors examined various industrial streams and the authors correlated their chemical composition to the solvent capacity. This work allowed the identification of the pseudo-components whose relative concentration is crucial for evaluating the solvent performances. Based on these data, the authors were able to find new products with ideal characteristics. The efficiency of one of these products was confirmed by the analysis of the data obtained when using this new solvent to remove asphaltene in damaged wells of an Italian field.

Del Bianco, A.; Stroppa, F.; Bertero, L.

1995-11-01T23:59:59.000Z

232

Vegetated Roof Water-Balance Model: Experimental and Model Results  

E-Print Network [OSTI]

urbanization effects on the water cycle. Although there are many stormwater best management practices (BMPs (ET) and soil media water storage between storm events. Lazzarin et al. (2005) estimated that ET ratesVegetated Roof Water-Balance Model: Experimental and Model Results James A. Sherrard Jr.1

233

Global longterm passive microwave satellitebased retrievals of vegetation optical depth  

E-Print Network [OSTI]

with those observed in the Advanced Very High Resolution Radiometer (AVHRR) Normalized Difference Vegetation the Advanced Very High Resolution Radiometer (AVHRR) extending back to 1981. The NDVI is derived by subtracting in the hydrological, energy and carbon cycles, through influences of land cover change on hydrologic responses

Evans, Jason

234

Soil and Vegetation Management: Keys to Water Conservation on Rangeland  

E-Print Network [OSTI]

The amount of water that soaks into the soil largely determines plant productivity. We can manage and conserve water where and when it falls, and by controlling the kind of vegetation we can make the fullest use of rain water. This publication...

Schuster, Joseph L.

2001-01-11T23:59:59.000Z

235

Sweet potatoes are a warm-weather vegetable  

E-Print Network [OSTI]

Sweet potatoes are a warm- weather vegetable related to the morning glory family.Although Louisiana sweet potatoes are often referred to as yams, they truly are sweet potatoes. The Louisiana producers began calling the orange-fleshed sweet potatoes grown in Louisiana"yams" to distinguish them from

236

A phenomenological model for the flow resistance over submerged vegetation  

E-Print Network [OSTI]

A phenomenological model for the flow resistance over submerged vegetation Alexandra G. Konings,1: Konings, A. G., G. G. Katul, and S. E. Thompson (2012), A phenomenological model for the flow resistance [2002]. In this paper, a phenomenological approach is used to describe the momentum transfer

Katul, Gabriel

237

9 Towards Adaptive Management of Native Vegetation in Regional Landscapes  

E-Print Network [OSTI]

management remains widely cited as the most logical and elegant frame- work for continuous improvement9 Towards Adaptive Management of Native Vegetation in Regional Landscapes David H Duncan1 of the `adaptive management' paradigm to natural resource man- agement, using regional management of native

Burgman, Mark

238

Beyond Biodiesel Running on Straight Vegetable Oil (SVO)  

E-Print Network [OSTI]

20 Beyond Biodiesel ­ Running on Straight Vegetable Oil (SVO) The green tree has many branches in the development and promotion of biodiesel for nearly two decades. Technologies based on the use of hydrogen in a low-percentage mixture with petroleum fuel. Hence the development of biodiesel. Paul Trella, New

Kaye, Jason P.

239

EVOLVING EXPECTATIONS OF DAM REMOVAL OUTCOMES: DOWNSTREAM GEOMORPHIC EFFECTS FOLLOWING REMOVAL OF A SMALL, GRAVEL-FILLED DAM1  

E-Print Network [OSTI]

EVOLVING EXPECTATIONS OF DAM REMOVAL OUTCOMES: DOWNSTREAM GEOMORPHIC EFFECTS FOLLOWING REMOVAL downstream were virtually undetectable. One year after dam removal, substrates of bars and riffles within 400 m downstream of the dam coarsened and a dominance of gravel and cobble sediments replaced previously

Tullos, Desiree

240

Fluoride removal from water with spent catalyst  

SciTech Connect (OSTI)

The adsorption of fluoride from water with spent catalyst was studied. Adsorption density of fluoride decreased with increasing pH. Linear adsorption isotherm was utilized to describe the adsorption reaction. The adsorption was a first-order reaction, and the rate constant increased with decreasing surface loading. Adsorption reaction of fluoride onto spent catalyst was endothermic, and the reaction rate increased slightly with increasing temperature. Fluoro-alumino complex and free fluoride ion were involved in the adsorption reaction. It is proposed that both the silica and alumina fractions of spent catalyst contribute to the removal of fluoride from aqueous solution. Coulombic interaction is proposed as the major driving force of the adsorption reaction of fluoride onto spent catalyst.

Lai, Y.D.; Liu, J.C. [National Taiwan Institute of Technology, Taipei (Taiwan, Province of China)

1996-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

AX Tank Farm tank removal study  

SciTech Connect (OSTI)

This report examines the feasibility of remediating ancillary equipment associated with the 241-AX Tank Farm at the Hanford Site. Ancillary equipment includes surface structures and equipment, process waste piping, ventilation components, wells, and pits, boxes, sumps, and tanks used to make waste transfers to/from the AX tanks and adjoining tank farms. Two remedial alternatives are considered: (1) excavation and removal of all ancillary equipment items, and (2) in-situ stabilization by grout filling, the 241-AX Tank Farm is being employed as a strawman in engineering studies evaluating clean and landfill closure options for Hanford single-shell tanks. This is one of several reports being prepared for use by the Hanford Tanks Initiative Project to explore potential closure options and to develop retrieval performance evaluation criteria for tank farms.

SKELLY, W.A.

1999-02-24T23:59:59.000Z

242

IMPROVED PROCESSES TO REMOVE NAPHTHENIC ACIDS  

SciTech Connect (OSTI)

In the first year of this project, we have established our experimental and theoretical methodologies for studies of the catalytic decarboxylation process. We have developed both glass and stainless steel micro batch type reactors for the fast screening of various catalysts with reaction substrates of model carboxylic acid compounds and crude oil samples. We also developed novel product analysis methods such as GC analyses for organic acids and gaseous products; and TAN measurements for crude oil. Our research revealed the effectiveness of several solid catalysts such as NA-Cat-1 and NA-Cat-2 for the catalytic decarboxylation of model compounds; and NA-Cat-5{approx}NA-Cat-9 for the acid removal from crude oil. Our theoretical calculations propose a three-step concerted oxidative decarboxylation mechanism for the NA-Cat-1 catalyst.

Aihua Zhang; Qisheng Ma; William A. Goddard; Yongchun Tang

2004-04-28T23:59:59.000Z

243

Removing sulphur oxides from a fluid stream  

DOE Patents [OSTI]

A process for removing sulphur oxides from a fluid stream, such as flue gas, comprising: providing a non-aqueous absorption liquid containing at least one hydrophobic amine, the liquid being incompletely miscible with water; treating the fluid stream in an absorption zone with the non-aqueous absorption liquid to transfer at least part of the sulphur oxides into the non-aqueous absorption liquid and to form a sulphur oxide-hydrophobic amine-complex; causing the non-aqueous absorption liquid to be in liquid-liquid contact with an aqueous liquid whereby at least part of the sulphur oxide-hydrophobic amine-complex is hydrolyzed to release the hydrophobic amine and sulphurous hydrolysis products, and at least part of the sulphurous hydrolysis products is transferred into the aqueous liquid; separating the aqueous liquid from the non-aqueous absorption liquid. The process mitigates absorbent degradation problems caused by sulphur dioxide and oxygen in flue gas.

Katz, Torsten; Riemann, Christian; Bartling, Karsten; Rigby, Sean Taylor; Coleman, Luke James Ivor; Lail, Marty Alan

2014-04-08T23:59:59.000Z

244

Apparatus for removing micronized coal from steam  

SciTech Connect (OSTI)

Micronized coal is removed from coal-bearing steam by spraying stabilized petroleum oil into the steam and directing the resultant stream at a separation surface on which a coal-oil slurry is deposited and collected. Apparatus includes conduits which direct the resultant stream downward into a housing and normal to a surface on which the slurry is deposited by impact forces. In additional apparatus disclosed, the resultant stream is directed from a horizontal conduit circumferentially along the interior wall of a horizontally disposed cylindrical chamber at the top of the chamber and the coal-oil slurry deposited on the wall by centrifugal force is collected in a trough situated below a longitudinal slot at the bottom of the chamber. In both types of apparatus, after separation of the slurry the velocity of the steam is reduced to settle out remaining oil droplets and is then discharged to the atmosphere.

Vlnaty, J.

1981-12-15T23:59:59.000Z

245

CHANGES IN 137 CS CONCENTRATIONS IN SOIL AND VEGETATION ON THE FLOODPLAIN OF THE SAVANNAH RIVER OVER A 30 YEAR PERIOD  

SciTech Connect (OSTI)

{sup 137}Cs released during 1954-1974 from nuclear production reactors on the Savannah River Site, a US Department of Energy nuclear materials production site in South Carolina, contaminated a portion of the Savannah River floodplain known as Creek Plantation. {sup 137}Cs activity concentrations have been measured in Creek Plantation since 1974 making it possible to calculate effective half-lives for {sup 137}Cs in soil and vegetation and assess the spatial distribution of contaminants on the floodplain. Activity concentrations in soil and vegetation were higher near the center of the floodplain than near the edges as a result of frequent inundation coupled with the presence of low areas that trapped contaminated sediments. {sup 137}Cs activity was highest near the soil surface, but depth related differences diminished with time as a likely result of downward diffusion or leaching. Activity concentrations in vegetation were significantly related to concentrations in soil. The plant to soil concentration ratio (dry weight) averaged 0.49 and exhibited a slight but significant tendency to decrease with time. The effective half-lives for {sup 137}Cs in shallow (0-7.6 cm) soil and in vegetation were 14.9 (95% CI = 12.5-17.3) years and 11.6 (95% CI = 9.1-14.1) years, respectively, and rates of {sup 137}Cs removal from shallow soil and vegetation did not differ significantly among sampling locations. Potential health risks on the Creek Plantation floodplain have declined more rapidly than expected on the basis of radioactive decay alone because of the relatively short effective half-life of {sup 137}Cs.

Paller, M.; Jannik, T.; Fledderman, P.

2007-12-12T23:59:59.000Z

246

High SO2 Removal Efficiency Testing  

SciTech Connect (OSTI)

This document provides a discussion of the technical progress on DOE/PETC project number DE-AC22-92PC91338, "High Efficiency SO2 Removal Testing", for the time period 1 January through 31 March 1997. The project involves testing at six full-scale utility flue gas desulfurization (FGD) systems, to evaluate low capital cost upgrades that may allow these systems to achieve up to 98% SO2 removal efficiency. The upgrades being evaluated mostly involve using performance additives in the FGD systems. The "base" project involved testing at the Tampa Electric Company?s Big Bend Station. All five potential options to the base program have been exercised by DOE, involving testing at Hoosier Energy?s Merom Station (Option I), Southwestern Electric Power Company?s Pirkey Station (Option II), PSI Energy?s Gibson Station (Option III), Duquesne Light?s Elrama Station (Option IV), and New York State Electric and Gas Corporation?s (NYSEG) Kintigh Station (Option V). The originally planned testing has been completed for all six sites. However, additional testing is planned at the Big Bend Station. The remainder of this document is divided into four sections. Section 2, Project Summary, provides a brief overview of the status of technical efforts on this project. Section 3, Results, summarizes the outcome from technical efforts during the quarter, or results from prior quarters that have not been previously reported. In Section 4, Plans for the Next Reporting Period, an overview is provided of the technical efforts that are anticipated for the second quarter of calendar year 1997. Section 5 contains a brief acknowledgement.

Gary Blythe

1997-04-23T23:59:59.000Z

247

PRECOMBUSTION REMOVAL OF HAZARDOUS AIR POLLUTANT PRECURSORS  

SciTech Connect (OSTI)

In response to growing environmental concerns reflected in the 1990 Clean Air Act Amendment (CAAA), the United States Department of Energy (DOE) sponsored several research and development projects in late 1995 as part of an initiative entitled Advanced Environmental Control Technologies for Coal-Based Power Systems. The program provided cost-shared support for research and development projects that could accelerate the commercialization of affordable, high-efficiency, low-emission, coal-fueled electric generating technologies. Clean coal technologies developed under this program would serve as prototypes for later generations of technologies to be implemented in the industrial sector. In order to identify technologies with the greatest potential for commercial implementation, projects funded under Phase I of this program were subject to competitive review by DOE before being considered for continuation funding under Phase II. One of the primary topical areas identified under the DOE initiative relates to the development of improved technologies for reducing the emissions of air toxics. Previous studies have suggested that many of the potentially hazardous air pollutant precursors (HAPPs) occur as trace elements in the mineral matter of run-of-mine coals. As a result, these elements have the potential to be removed prior to combustion at the mine site by physical coal cleaning processes (i.e., coal preparation). Unfortunately, existing coal preparation plants are generally limited in their ability to remove HAPPs due to incomplete liberation of the mineral matter and high organic associations of some trace elements. In addition, existing physical coal cleaning plants are not specifically designed or optimized to ensure that high trace element rejections may be achieved.

Unknown

2000-10-09T23:59:59.000Z

248

Gravel admix, vegetation, and soil water interactions in protective barriers: Experimental design, construction, and initial conditions  

SciTech Connect (OSTI)

The purpose of this study is to measure the interactive effects of gravel admix and greater precipitation on soil water storage and plant abundance. The study is one of many tasks in the Protective Barrier Development Program for the disposal of Hanford defense waste. A factorial field-plot experiment was set up at the site selected as the borrow area for barrier topsoil. Gravel admix, vegetation, and enhanced precipitation treatments were randomly assigned to the plots using a split-split plot design structure. Changes in soil water storage and plant cover were monitored using neutron probe and point intercept methods, respectively. The first-year results suggest that water extraction by plants will offset gravel-caused increases in soil water storage. Near-surface soil water contents were much lower in graveled plots with plants than in nongraveled plots without plants. Large inherent variability in deep soil water storage masked any effects gravel may have had on water content below the root zone. In the future, this source of variation will be removed by differencing monthly data series and testing for changes in soil water storage. Tests of the effects of greater precipitation on soil water storage were inconclusive. A telling test will be possible in the spring of 1988, following the first wet season during which normal precipitation is doubled. 26 refs., 9 figs., 9 tabs.

Waugh, W.J.

1989-05-01T23:59:59.000Z

249

Modeled Impacts of Cover Crops and Vegetative Barriers on Corn Stover Availability and Soil Quality  

SciTech Connect (OSTI)

Environmentally benign, economically viable, and socially acceptable agronomic strategies are needed to launch a sustainable lignocellulosic biofuel industry. Our objective was to demonstrate a landscape planning process that can ensure adequate supplies of corn (Zea mays L.) stover feedstock while protecting and improving soil quality. The Landscape Environmental Assessment Framework (LEAF) was used to develop land use strategies that were then scaled up for five U.S. Corn Belt states (Nebraska, Iowa, Illinois, Indiana, and Minnesota) to illustrate the impact that could be achieved. Our results show an annual sustainable stover supply of 194 million Mg without exceeding soil erosion T values or depleting soil organic carbon [i.e., soil conditioning index (SCI)?>?0] when no-till, winter cover crop, and vegetative barriers were incorporated into the landscape. A second, more rigorous conservation target was set to enhance soil quality while sustainably harvesting stover. By requiring erosion to be <1/2 T and the SCI-organic matter (OM) subfactor to be >?0, the annual sustainable quantity of harvestable stover dropped to148 million Mg. Examining removal rates by state and soil resource showed that soil capability class and slope generally determined the effectiveness of the three conservation practices and the resulting sustainable harvest rate. This emphasizes that sustainable biomass harvest must be based on subfield management decisions to ensure soil resources are conserved or enhanced, while providing sufficient biomass feedstock to support the economic growth of bioenergy enterprises.

Ian J. Bonner; David J. Muth Jr.; Joshua B. Koch; Douglas L. Karlen

2014-06-01T23:59:59.000Z

250

The role of vegetation in the CO[subscript 2] flux from a tropical urban neighbourhood  

E-Print Network [OSTI]

Urban surfaces are usually net sources of CO[subscript 2]. Vegetation can potentially have an important role in reducing the CO[subscript 2] emitted by anthropogenic activities in cities, particularly when vegetation is ...

Velasco, E.

251

E-Print Network 3.0 - affecting vegetable stand Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Summary: non-vegetative ground cover. For example, if running water covers 1% of your station, standing water 2... . If a habitat is flooded but Live vegetation ground cover...

252

Vegetation and sediment characteristics of created and natural Spartina alterniflora marshes in Lower Galveston Bay, Texas  

E-Print Network [OSTI]

Five natural and ten created Spartina altemiflora marshes in the Lower Galveston Bay System, Texas, were compared to determine if there were significantly different vegetative and sediment characteristics associated with each marsh type. Vegetative...

Albertson, Andrea Kai

1998-01-01T23:59:59.000Z

253

Optimization of Geoscience Laser Altimeter System waveform metrics to support vegetation measurements  

E-Print Network [OSTI]

Optimization of Geoscience Laser Altimeter System waveform metrics to support vegetation GLAS Optimization Remote sensing Vegetation structure The Geoscience Laser Altimeter System (GLAS) has optimized a noise coefficient which could be constant or vary according to observation period or noise

Lefsky, Michael

254

Measurements and Linear Wave Theory Based Simulations of Vegetated Wave Hydrodynamics for Practical Applications  

E-Print Network [OSTI]

Wave attenuation by vegetation is a highly dynamic process and its quantification is important for accurately understanding and predicting coastal hydrodynamics. However, the influence of vegetation on wave dissipation is not yet fully established...

Anderson, Mary Elizabeth

2011-10-21T23:59:59.000Z

255

Best Management Practices for Aquatic Vegetation Management Principal Investigator: Joseph E. Morris  

E-Print Network [OSTI]

. Develop educational materials related to aquatic plant identification and their specific managementBest Management Practices for Aquatic Vegetation Management Principal Investigator: Joseph E vegetation management with the ultimate goal of producing the best management practices protocol in Iowa

Koford, Rolf R.

256

Self-consistent photothermal techniques: Application for measuring thermal diffusivity in vegetable oils  

E-Print Network [OSTI]

Self-consistent photothermal techniques: Application for measuring thermal diffusivity in vegetable of vegetable oils. The thermal diffusivity of six commercial vegetable oils olive, corn, soybean, canola in terms of thermal diffusivity was shown. The high measurement precision of the TWRC highlights

Mandelis, Andreas

257

Updated March 2013 Eat Smart, Live Strong is designed to improve fruit and vegetable consumption and  

E-Print Network [OSTI]

Updated March 2013 Eat Smart, Live Strong is designed to improve fruit and vegetable consumption: · eat at least 3 ½ cups of fruit and vegetable per day (1 ½ cups of fruits and 2 cups of vegetables;Session 1, Reach Your Goals, Step by Step allows participants to review the amount of fruits

258

ForPeerReview From vegetable oils to polyurethanes: synthetic routes to  

E-Print Network [OSTI]

From vegetable oils to polyurethanes: synthetic routes to polyols and main industrial products Myriam and main industrial products Most of biobased polyols for polyurethanes are synthesized from vegetable oils literature; focus on the industrial synthetic routes. Keywords: vegetable oils; biobased polyols

Boyer, Edmond

259

Fire recurrence in the subarctic and its implications for vegetation composition E. A. JOHNSON  

E-Print Network [OSTI]

Fire recurrence in the subarctic and its implications for vegetation composition E. A. JOHNSON JOHNSON,,E. A. 1979. Fire recurrence in the subarctic and its implications for vegetation composition. Can of the distribution's hazard of burning function to vegetation composition and r-K selection is discussed. JOHNSON,E

Johnson, Edward A.

260

ERDC/CERLTR-05-39 Simulation of Vegetation Recovery from  

E-Print Network [OSTI]

ERDC/CERLTR-05-39 Simulation of Vegetation Recovery from Military Disturbances on Fort Bliss Tamara of Vegetation Recovery from Military Disturbances on Fort Bliss Tamara Hochstrasser and Debra Peters USDA the vegetation simulation modeling capabilities of Fort Bliss, Texas, for evaluating the effects of military

Fehmi, Jeffrey S.

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Similar effects of residential and non-residential vegetation on bird diversity in suburban neighbourhoods  

E-Print Network [OSTI]

Similar effects of residential and non-residential vegetation on bird diversity in suburban the Queen in Right of Canada 2013 Abstract Estimating the relative importance of vegetation on residential land (gardens, yards, and street-trees) and vegetation on non-residential land (parks and other large

Dawson, Jeff W.

262

Vegetation survey of knapweed on the Yakima Training Center - 1992  

SciTech Connect (OSTI)

This report summarizes and discusses the results of a vegetation survey conducted in 1992 on a portion of the Yakima Training Center (YTC). Pacific Northwest Laboratory (PNL) conducted this survey and a similar survey in 1991 for the U.S. Department of the Army. The objectives of the survey were to evaluate the impact of the herbicide picloram on forbs where aerial applications of picloram were made in 1988, 1989, and 1991 to control knapweed infestations. Forbs are of special interest because they are an important part of the spring and summer diet of the western sage grouse, which is a U.S. Fish and Wildlife Service candidate species for the threatened and endangered list. We also conducted a limited evaluation of the effectiveness of the spray program in controlling the spread of knapweed. Percent plant canopy cover and number of forbs were measured on 120 transacts on the herbicide-treated and untreated control areas. Herbicide treatment in 1991 resulted in a significant reduction in knapweed based on percent cover and density. The treatment areas also all had lower percent canopy cover of perennial forbs and fewer perennial forbs compared to control areas. Canopy cover of shrubs and annual, biennial, and perennial forbs measured on the YTC increased between the 1991 and 1992 survey, which may indicate a recovery of these vegetation types after disturbance. These increases also could reflect the mild 1992 winter and superior growing conditions in the spring of 1992. We recommend that these vegetation transacts continue to be monitored for an additional growing season to evaluate (1) whether knapweed increases to its previous abundance in the 1991 herbicide-treated area, (2) the efficacy of herbicide application on transacts along roadways, and (3) the increase in invasive annuals in herbicide-treated areas and the possible effects on community vegetation structure and sage grouse habitat.

Downs, J.L.; Cadoret, N.A.; Rickard, W.H.

1994-04-01T23:59:59.000Z

263

Vegetation, edaphic, and topographic interrelationships in an East Texas forest  

E-Print Network [OSTI]

VEGETATION, EDAPHIC, AND TOPOGRAPHIC INTERRELATIONSHIPS IN AN EAST TEXAS FOREST A Thesis by JOHNNY ZANE HINTON Approved as to style and content by: (Chairman of Committee) (Member) (Member) (Head of Department) December 1981 ABSTRACT... Vegetat1on, Edaphic, and Topographic Interrelationsh1ps In an East Texas Forest. (Oecember 1981) Johnny Zane Hinton, B. S. , Texas A&M Un1versity Chairman of Advisory Committee: Dr. Fred E, Sme1ns Thirty stands were sampled on the Angelina National...

Hinton, Johnny Zane

1981-01-01T23:59:59.000Z

264

Iodine in Drinking Waters, Vegetables, Cottonseed Meal, and Roughages.  

E-Print Network [OSTI]

LIBRARY, A & M COLLEGE, G. S. FRAPS and J. F. FUDGE Division of Chemistry TEXAS AGRICULTURAL EXPERIMENT STATION A. B. CONNER, DIRECTOR, College Station, Texas BULLETIN NO. 595 NOVEMBER 1940 -- IODINE IN DRINKING WATERS, VEGETABLES..., COTTONSEED MEAL, AND ROUGEIAGES ! .I rq?,\\?Y - AGRICULTURAL AND MECHANICAL COLLEGE OF TEXAS T. 0. WALTON, President A96-1140-7M-LJ.80 5 [Blank Page in Original Bulletin] Iodine was determined in nearly 500 samples of city and rural drinking waters...

Fudge, J. F. (Joseph Franklin); Fraps, G. S. (George Stronach)

1940-01-01T23:59:59.000Z

265

Range Vegetation Response to Burning Thicketized Live Oak Savannah.  

E-Print Network [OSTI]

TABLE 9. TOTAL STANDING CROP OF LIVE OAK AND NEW GROWTH (KGIHA) AND STANDING CROP INCREASE ( REPRESENTED BY NEW GROWTH IN APRIL AND JULY, 1* ON AREAS BURNED AT VARIOUS DATES ON THE ARANS NATIONAL WILDLIFE REFUGE NEAR AUSTWELL, TEXAS' New growth2... Response of live oak-dominated vegetation on thicketized uplands to burning in the fall 1974, spring 1975, and fall 1975 was evaluated through 1977 on the Aransas National Wildlife Refuge. Standing crop, species diversity, and botanical composition...

Scifres, C.J.; Kelly, D.M.

1979-01-01T23:59:59.000Z

266

Activity of polymerized trichloroacetic acid for highway vegetation control  

E-Print Network [OSTI]

Mem r ember Play 1/74 ABSTRACT Activity of Polymer- zed Trichloroacetic Acid for Highway Vegetation Control. (May 1/74) Hobert Phillip Wieaenfeld, B. S. , California State University, Humboldt Chairman of Advisory Committee: Dr. Wayne G. Mc... applied to highway roadsides near Fort Worth, Lufkin and Yoakum, Texas in the spring of 1g'7$. Two polymerizing activates which differed in their solubility were used. TCA polymerized with the more soluble activate and applied at a rate of '3 lbs...

Wiedenfeld, R. P

1974-01-01T23:59:59.000Z

267

Vegetation survey of Pen Branch and Four Mile Creek wetlands  

SciTech Connect (OSTI)

One hundred-fifty plots were recently sampled (vegetational sampling study) at the Savannah River Site (SRS). An extensive characterization of the vascular flora, in four predetermined strata (overstory, Understory, shrub layer, and ground cover), was undertaken to determine dominance, co-dominance, and the importance value (I.V.) of each species. These results will be used by the Savannah River Laboratory (SRL) to evaluate the environmental status of Four Mile Creek, Pen Branch, and two upland pine stands. Objectives of this study were to: Describe in detail the plant communities previously mapped with reference to the topography and drainage, including species of plants present: Examine the successional trends within each sampling area and describe the extent to which current vegetation communities have resulted from specific earlier vegetation disturbances (e.g., logging and grazing); describe in detail the botanical field techniques used to sample the flora; describe the habitat and location of protected and/or rare species of plants; and collect and prepare plant species as herbarium quality specimens. Sampling was conducted at Four Mile Creek and Pen Branch, and in two upland pine plantations of different age growth.

Not Available

1992-10-01T23:59:59.000Z

268

Vegetation survey of Pen Branch and Four Mile Creek wetlands  

SciTech Connect (OSTI)

One hundred-fifty plots were recently sampled (vegetational sampling study) at the Savannah River Site (SRS). An extensive characterization of the vascular flora, in four predetermined strata (overstory, Understory, shrub layer, and ground cover), was undertaken to determine dominance, co-dominance, and the importance value (I.V.) of each species. These results will be used by the Savannah River Laboratory (SRL) to evaluate the environmental status of Four Mile Creek, Pen Branch, and two upland pine stands. Objectives of this study were to: Describe in detail the plant communities previously mapped with reference to the topography and drainage, including species of plants present: Examine the successional trends within each sampling area and describe the extent to which current vegetation communities have resulted from specific earlier vegetation disturbances (e.g., logging and grazing); describe in detail the botanical field techniques used to sample the flora; describe the habitat and location of protected and/or rare species of plants; and collect and prepare plant species as herbarium quality specimens. Sampling was conducted at Four Mile Creek and Pen Branch, and in two upland pine plantations of different age growth.

Not Available

1992-01-01T23:59:59.000Z

269

Removal of radioactive and other hazardous material from fluid waste  

DOE Patents [OSTI]

Hollow glass microspheres obtained from fly ash (cenospheres) are impregnated with extractants/ion-exchangers and used to remove hazardous material from fluid waste. In a preferred embodiment the microsphere material is loaded with ammonium molybdophosphonate (AMP) and used to remove radioactive ions, such as cesium-137, from acidic liquid wastes. In another preferred embodiment, the microsphere material is loaded with octyl(phenyl)-N-N-diisobutyl-carbamoylmethylphosphine oxide (CMPO) and used to remove americium and plutonium from acidic liquid wastes.

Tranter, Troy J. (Idaho Falls, ID); Knecht, Dieter A. (Idaho Falls, ID); Todd, Terry A. (Aberdeen, ID); Burchfield, Larry A. (W. Richland, WA); Anshits, Alexander G. (Krasnoyarsk, RU); Vereshchagina, Tatiana (Krasnoyarsk, RU); Tretyakov, Alexander A. (Zheleznogorsk, RU); Aloy, Albert S. (St. Petersburg, RU); Sapozhnikova, Natalia V. (St. Petersburg, RU)

2006-10-03T23:59:59.000Z

270

Thiacrown polymers for removal of mercury from waste streams  

DOE Patents [OSTI]

Thiacrown polymers immobilized to a polystyrene-divinylbenzene matrix react with Hg.sup.2+ under a variety of conditions to efficiently and selectively remove Hg.sup.2+ ions from acidic aqueous solutions, even in the presence of a variety of other metal ions. The mercury can be recovered and the polymer regenerated. This mercury removal method has utility in the treatment of industrial wastewater, where a selective and cost-effective removal process is required.

Baumann, Theodore F. (Tracy, CA); Reynolds, John G. (San Ramon, CA); Fox, Glenn A. (Livermore, CA)

2002-01-01T23:59:59.000Z

271

Heat recirculating cooler for fluid stream pollutant removal  

DOE Patents [OSTI]

A process by which heat is removed from a reactant fluid to reach the operating temperature of a known pollutant removal method and said heat is recirculated to raise the temperature of the product fluid. The process can be utilized whenever an intermediate step reaction requires a lower reaction temperature than the prior and next steps. The benefits of a heat-recirculating cooler include the ability to use known pollutant removal methods and increased thermal efficiency of the system.

Richards, George A. (Morgantown, WV); Berry, David A. (Morgantown, WV)

2008-10-28T23:59:59.000Z

272

Organic removal from domestic wastewater by activated alumina adsorption  

E-Print Network [OSTI]

of the major groups of pollutants in wastewaters. Adsorption by granular activated carbon, a non-polar adsorbent, is now the primary treatment process for removal of residual organics from biologically treated wastewater. The ability of activated alumina... to human health if they exist in the water supply at relatively high concentrations. A wide variety of treatment processes are available to remove organic matter from wastewater. Biological treatment is the most cost effective method for removing oxygen...

Yang, Pe-Der

1982-01-01T23:59:59.000Z

273

Removal of Radiocesium from Food by Processing: Data Collected after the Fukushima Daiichi Nuclear Power Plant Accident - 13167  

SciTech Connect (OSTI)

Removal of radiocesium from food by processing is of great concern following the accident of TEPCO's Fukushima Daiichi Nuclear Power Plant accident. Foods in markets are monitored and recent monitoring results have shown that almost all food materials were under the standard limit concentration levels for radiocesium (Cs-134+137), that is, 100 Bq kg{sup -1} in raw foods, 50 Bq kg{sup -1} in baby foods, and 10 Bq kg{sup -1} in drinking water; those food materials above the limit cannot be sold. However, one of the most frequently asked questions from the public is how much radiocesium in food would be removed by processing. Hence, information about radioactivity removal by processing of food crops native to Japan is actively sought by consumers. In this study, the food processing retention factor, F{sub r}, which is expressed as total activity in processed food divided by total activity in raw food, is reported for various types of corps. For white rice at a typical polishing yield of 90-92% from brown rice, the F{sub r} value range was 0.42-0.47. For leafy vegetable (indirect contamination), the average F{sub r} values were 0.92 (range: 0.27-1.2) after washing and 0.55 (range: 0.22-0.93) after washing and boiling. The data for some fruits are also reported. (authors)

Uchida, Shigeo; Tagami, Keiko [Office of Biospheric Assessment for Waste Disposal, National Institute of Radiological Sciences, Anagawa 4-9-1, Inage-ku, Chiba 263-8555 (Japan)] [Office of Biospheric Assessment for Waste Disposal, National Institute of Radiological Sciences, Anagawa 4-9-1, Inage-ku, Chiba 263-8555 (Japan)

2013-07-01T23:59:59.000Z

274

NNSA's Global Threat Reduction Initiative Removes More Than One...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Press Releases Video Gallery Photo Gallery Jobs Apply for Our Jobs Our Jobs Working at NNSA Blog Home NNSA Blog NNSA's Global Threat Reduction Initiative Removes More ......

275

Performance evaluation of organic emulsion liquid membrane on phenol removal  

E-Print Network [OSTI]

The percentage removal of phenol from aqueous solution by emulsion liquid membrane and emulsion leakage was investigated experimentally for various parameters such as membrane:internal phase ratio, membrane:external phase ratio, emulsification speed, emulsification time, carrier concentration, surfactant concentration and internal agent concentration. These parameters strongly influence the percentage removal of phenol and emulsion leakage. Under optimum membrane properties, the percentage removal of phenol was as high as 98.33%, with emulsion leakage of 1.25%. It was also found that the necessity of carrier for enhancing phenol removal was strongly dependent on the internal agent concentration.

Ng, Y S; Hashim, M A

2014-01-01T23:59:59.000Z

276

SEPARATION OF HEAVY METALS: REMOVAL FROM INDUSTRIAL WASTEWATERS  

Office of Scientific and Technical Information (OSTI)

a two- or three-stage operation to remove the metals and 0il sepcrately). ComplexationSequestration Complexation involves the formation of a complex or chelating agent....

277

Safety evaluation for packaging (onsite) product removal can containers  

SciTech Connect (OSTI)

This safety evaluation for packaging allows the transport of nine Product Removal (PR) Cans with their Containers from the PUREX Facility to the Plutonium Finishing Plant.

Boettger, J.S.

1997-04-29T23:59:59.000Z

278

active debris removal: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Rebecca Bendick a , Kevin D. Hyde b March 2013 Keywords: Debris flow Frequency Magnitude Fire Forecasting debris flow hazard is challenging Montana, University of 110 Removing...

279

Use, Maintenance, Removal, Inspections, and Safety of Dams (Iowa)  

Broader source: Energy.gov [DOE]

This section describes operating plans for dams with movable structures, as well as procedures for raising or lowering of impoundment levels, dam removal, and dam safety inspections.

280

Process to remove rare earth from IFR electrolyte  

DOE Patents [OSTI]

The invention is a process for the removal of rare earths from molten chloride electrolyte salts used in the reprocessing of integrated fast reactor fuel (IFR). The process can be used either continuously during normal operation of the electrorefiner or as a batch process. The process consists of first separating the actinide values from the salt before purification by removal of the rare earths. After replacement of the actinides removed in the first step, the now-purified salt electrolyte has the same uranium and plutonium concentration and ratio as when the salt was removed from the electrorefiner. 1 fig.

Ackerman, J.P.; Johnson, T.R.

1994-08-09T23:59:59.000Z

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Study of Alternative Approaches for Transite Panel Removal |...  

Broader source: Energy.gov (indexed) [DOE]

(BJC) assembled an experienced team from both sites to evaluate both the manual and mechanical methods of transite panel removal. Study of Alternative Approaches for Transite...

282

anesthesia optimizing removal: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

de 7 Multiplicative Noise Removal Using Variable Splitting and Constrained Optimization CERN Preprints Summary: Multiplicative noise (also known as speckle noise) models...

283

Removal of Carbon Tetrachloride from a Layered Porous Medium...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Carbon Tetrachloride from a Layered Porous Medium by Means of Soil Vapor Extraction Enhanced by Desiccation and Water Removal of Carbon Tetrachloride from a Layered Porous Medium...

284

Removal of carbon tetrachloride from a layered porous medium...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

carbon tetrachloride from a layered porous medium by means of soil vapor extraction enhanced by desiccation and water Removal of carbon tetrachloride from a layered porous medium...

285

Method of removal of sulfur from coal and petroleum products  

DOE Patents [OSTI]

A method for the removal of sulfur from sulfur-bearing materials such as coal and petroleum products using organophosphine and organophosphite compounds is provided.

Verkade, John G. (Ames, IA); Mohan, Thyagarajan (Ames, IA); Angelici, Robert J. (Ames, IA)

1995-01-01T23:59:59.000Z

286

Process to remove rare earth from IFR electrolyte  

DOE Patents [OSTI]

The invention is a process for the removal of rare earths from molten chloride electrolyte salts used in the reprocessing of integrated fast reactor fuel (IFR). The process can be used either continuously during normal operation of the electrorefiner or as a batch process. The process consists of first separating the actinide values from the salt before purification by removal of the rare earths. After replacement of the actinides removed in the first step, the now-purified salt electrolyte has the same uranium and plutonium concentration and ratio as when the salt was removed from the electrorefiner.

Ackerman, J.P.; Johnson, T.R.

1992-01-01T23:59:59.000Z

287

REMOVAL OF THE CALIFORNIUM SOURCES FROM THE 222-S LABORATORY  

SciTech Connect (OSTI)

This document develops a proposal for removal of 2-Californium sources from the 222-S Laboratory. Included in this document are assessments of shipping packages and decay calculations.

LINSTRUM D; BAUNE HL

2009-07-23T23:59:59.000Z

288

Process to remove rare earth from IFR electrolyte  

DOE Patents [OSTI]

The invention is a process for the removal of rare earths from molten chloride electrolyte salts used in the reprocessing of integrated fast reactor fuel (IFR). The process can be used either continuously during normal operation of the electrorefiner or as a batch process. The process consists of first separating the actinide values from the salt before purification by removal of the rare earths. After replacement of the actinides removed in the first step, the now-purified salt electrolyte has the same uranium and plutonium concentration and ratio as when the salt was removed from the electrorefiner.

Ackerman, John P. (Downers Grove, IL); Johnson, Terry R. (Wheaton, IL)

1994-01-01T23:59:59.000Z

289

South Africa HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

South Africa HEU Removal | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing Proliferation Powering the...

290

Method of removing oxidized contaminants from water  

DOE Patents [OSTI]

The present invention is a method for removing oxidized contaminant(s) from water. More specifically, the invention has the steps of contacting water containing the oxidized contaminant(s) with a layered aluminosilicate having Fe(II). The aluminosilicate may contain naturally occurring Fe(II), or the Fe(II) may be produced by reducing Fe(III) that is initially present. Reduction may be either by exposure to a chemical or biological reductant. Contacting the water containing oxidized contaminant(s) may be by (1) injection of Fe(II)-containing layered aluminosilicate, via a well, into a saturated zone where it is likely to intercept the contaminated water; (2) injection of contaminated water into a vessel containing the Fe(II)-bearing layered aluminosilicate; and (3) first reducing Fe(III) in the layered aluminosilicate to Fe(II) by injection of a biological or chemical reductant, into an aquifer or vessel having sufficient Fe(III)-bearing aluminosilicate to produce the necessary Fe(II). 8 figs.

Amonette, J.E.; Fruchter, J.S.; Gorby, Y.A.; Cole, C.R.; Cantrell, K.J.; Kaplan, D.I.

1998-07-21T23:59:59.000Z

291

Method of removing oxidized contaminants from water  

DOE Patents [OSTI]

The present invention is a method for removing oxidized contaminant(s) from water. More specifically, the invention has the steps of contacting water containing the oxidized contaminant(s) with a layered aluminosilicate having Fe(II). The aluminosilicate may contain naturally occurring Fe(II), or the Fe(II) may be produced by reducing Fe(III) that is initially present. Reduction may be either by exposure to a chemical or biological reductant. Contacting the water containing oxidized contaminant(s) may be by (1) injection of Fe(II)-containing layered aluminosilicate, via a well, into a saturated zone where it is likely to intercept the contaminated water; (2) injection of contaminated water into a vessel containing the Fe(II)-bearing layered aluminosilicate; and (3) first reducing Fe(III) in the layered aluminosilicate to Fe(II) by injection of a biological or chemical reductant, into an aquifer or vessel having sufficient Fe(III)-bearing aluminosilicate to produce the necessary Fe(II).

Amonette, James E. (Richland, WA); Fruchter, Jonathan S. (Richland, WA); Gorby, Yuri A. (Richland, WA); Cole, Charles R. (West Richmond, WA); Cantrell, Kirk J. (West Richmond, WA); Kaplan, Daniel I. (Richland, WA)

1998-01-01T23:59:59.000Z

292

The washability of lignites for clay removal  

SciTech Connect (OSTI)

In the washability research of the Seyitomer Lignites (Kutahya-Turkey), with lower calorific value (1,863 kcal/kg) and high ash content (51.91%), by heavy medium separation, it was found out that middling clay in the coal had an effect to change the medium density. To prevent this problem, a trommel sieve with 18 and 5 mm aperture diameter was designed, and the clay in the coal was tried to be removed using it before the coal was released to heavy medium. Following that, the obtained coal in -100 + 18 mm and -18 + 5 mm fractions was subjected to sink and float test having 1.4 gcm{sup -3} and 1.7 gcm{sup -3} medium densities (-5 mm fraction will be evaluated in a separate work). Depending on the raw coal, with the floating of -100 + 18 mm and -18 + 5 mm size fraction in 1.4 gcm{sup -3} medium density, clean coal with 60.10% combustible matter recovery, 19.12% ash, and 3,150 kcal/kg was obtained. Also floating of the samples sinking in 1.4 gcm{sup -3} in the medium density (1.7 gcm{sup -3}), middling with 18.70% combustible matter recovery, 41.93% ash, 2,150 kcal/kg, and tailing having 78.31% ash were obtained.

Oteyaka, B.; Yamik, A.; Ucar, A.; Sahbaz, O.; Demir, U. [Dumlupinar University, Kutahya (Turkey). Dept. of Mining Engineering

2008-07-01T23:59:59.000Z

293

Improved Processes to Remove Naphthenic Acids  

SciTech Connect (OSTI)

In the past three years, we followed the work plan as we suggested in the proposal and made every efforts to fulfill the project objectives. Based on our large amount of creative and productive work, including both of experimental and theoretic aspects, we received important technical breakthrough on naphthenic acid removal process and obtained deep insight on catalytic decarboxylation chemistry. In detail, we established an integrated methodology to serve for all of the experimental and theoretical work. Our experimental investigation results in discovery of four type effective catalysts to the reaction of decarboxylation of model carboxylic acid compounds. The adsorption experiment revealed the effectiveness of several solid materials to naphthenic acid adsorption and acidity reduction of crude oil, which can be either natural minerals or synthesized materials. The test with crude oil also received promising results, which can be potentially developed into a practical process for oil industry. The theoretical work predicted several possible catalytic decarboxylation mechanisms that would govern the decarboxylation pathways depending on the type of catalysts being used. The calculation for reaction activation energy was in good agreement with our experimental measurements.

Aihua Zhang; Qisheng Ma; Kangshi Wang; Yongchun Tang; William A. Goddard

2005-12-09T23:59:59.000Z

294

Metagenomic analysis of phosphorus removing sludgecommunities  

SciTech Connect (OSTI)

Enhanced Biological Phosphorus Removal (EBPR) is not wellunderstood at the metabolic level despite being one of the best-studiedmicrobially-mediated industrial processes due to its ecological andeconomic relevance. Here we present a metagenomic analysis of twolab-scale EBPR sludges dominated by the uncultured bacterium, "CandidatusAccumulibacter phosphatis." This analysis resolves several controversiesin EBPR metabolic models and provides hypotheses explaining the dominanceof A. phosphatis in this habitat, its lifestyle outside EBPR and probablecultivation requirements. Comparison of the same species from differentEBPR sludges highlights recent evolutionary dynamics in the A. phosphatisgenome that could be linked to mechanisms for environmental adaptation.In spite of an apparent lack of phylogenetic overlap in the flankingcommunities of the two sludges studied, common functional themes werefound, at least one of them complementary to the inferred metabolism ofthe dominant organism. The present study provides a much-needed blueprintfor a systems-level understanding of EBPR and illustrates thatmetagenomics enables detailed, often novel, insights into evenwell-studied biological systems.

Garcia Martin, Hector; Ivanova, Natalia; Kunin, Victor; Warnecke,Falk; Barry, Kerrie; McHardy, Alice C.; Yeates, Christine; He, Shaomei; Salamov, Asaf; Szeto, Ernest; Dalin, Eileen; Putnam, Nik; Shapiro, HarrisJ.; Pangilinan, Jasmyn L.; Rigoutsos, Isidore; Kyrpides, Nikos C.; Blackall, Linda Louise; McMahon, Katherine D.; Hugenholtz, Philip

2006-02-01T23:59:59.000Z

295

Passive shut-down heat removal system  

DOE Patents [OSTI]

An improved shut-down heat removal system for a liquid metal nuclear reactor of the type having a vessel for holding hot and cold pools of liquid sodium is disclosed herein. Generally, the improved system comprises a redan or barrier within the reactor vessel which allows an auxiliary heat exchanger to become immersed in liquid sodium from the hot pool whenever the reactor pump fails to generate a metal-circulating pressure differential between the hot and cold pools of sodium. This redan also defines an alternative circulation path between the hot and cold pools of sodium in order to equilibrate the distribution of the decay heat from the reactor core. The invention may take the form of a redan or barrier that circumscribes the inner wall of the reactor vessel, thereby defining an annular space therebetween. In this embodiment, the bottom of the annular space communicates with the cold pool of sodium, and the auxiliary heat exchanger is placed in this annular space just above the drawn-down level that the liquid sodium assumes during normal operating conditions. Alternatively, the redan of the invention may include a pair of vertically oriented, concentrically disposed standpipes having a piston member disposed between them that operates somewhat like a pressure-sensitive valve. In both embodiments, the cessation of the pressure differential that is normally created by the reactor pump causes the auxiliary heat exchanger to be immersed in liquid sodium from the hot pool. Additionally, the redan in both embodiments forms a circulation flow path between the hot and cold pools so that the decay heat from the nuclear core is uniformly distributed within the vessel.

Hundal, Rolv (Greensburg, PA); Sharbaugh, John E. (Bullskin Township, Fayette County, PA)

1988-01-01T23:59:59.000Z

296

NDE Studies on CRDMs Removed From Service  

SciTech Connect (OSTI)

Studies being conducted at the Pacific Northwest National Laboratory (PNNL) in Richland, Washington are focused on assessing the effectiveness of NDE inspections of control rod drive mechanism (CRDM) nozzles and J-groove weldments. The primary objective of this work is to provide information to the United States Nuclear Regulatory Commission (US NRC) on the effectiveness of ultrasonic testing (UT) and eddy current testing (ET) as related to the in-service inspection of CRDM nozzles and J-groove weldments, and to enhance the knowledge base of primary water stress corrosion cracking (PWSCC) through destructive characterization of the CRDM assemblies. In describing two CRDM assemblies removed from service, decontaminated, and then used in a series of NDE measurements, this paper will address the following questions: 1) What did each technique detect?, 2) What did each technique miss?, 3) How accurately did each technique characterize the detected flaws? Two CRDM assemblies including the CRDM nozzle, the J-groove weld, buttering, and a portion of the ferritic head material were selected for this study. One contained suspected PWSCC, based on in-service inspection data; the other contained evidence suggesting through-wall leakage, but this was unconfirmed. The selected NDE measurements follow standard industry techniques for conducting in-service inspections of CRDM nozzles and the crown of the J-groove welds and buttering. In addition, laboratory based NDE methods will be employed to conduct inspections of the CRDM assemblies, with particular emphasis on inspecting the J-groove weld and buttering. This paper will also describe the NDE methods used and discus the NDE results. Future work will involve using the results from these NDE studies to guide the development of a destructive characterization plan to reveal the crack morphology, to be compared with NDE responses.

Doctor, Steven R.; Cumblidge, Stephen E.; Schuster, George J.; Hockey, Ronald L.; Abrefah, John

2005-12-31T23:59:59.000Z

297

The Asian Tsunami: A Protective Role for Coastal Vegetation  

E-Print Network [OSTI]

- etation may shield coastlines from tsunami damage by reducing wave amplitude and energy (2). Analytical). At the river mouth, the tsunami completely destroyed parts of a village (fig. S1) and removed a sand spit, Greenbelt Tsunami Prevention in South-Pacific Region, available at http://eqtap. edm.bosai.go.jp/useful_outputs/report

Gray, Matthew

298

Process for removing pyritic sulfur from bituminous coals  

DOE Patents [OSTI]

A process is provided for removing pyritic sulfur and lowering ash content of bituminous coals by grinding the feed coal, subjecting it to micro-agglomeration with a bridging liquid containing heavy oil, separating the microagglomerates and separating them to a water wash to remove suspended pyritic sulfur. In one embodiment the coal is subjected to a second micro-agglomeration step.

Pawlak, Wanda (Edmonton, CA); Janiak, Jerzy S. (Edmonton, CA); Turak, Ali A. (Edmonton, CA); Ignasiak, Boleslaw L. (Edmonton, CA)

1990-01-01T23:59:59.000Z

299

Removal of residual particulate matter from filter media  

DOE Patents [OSTI]

A method for removing residual filter cakes that remain adhered to a filter after typical particulate removal methodologies have been employed, such as pulse-jet filter element cleaning, for all cleanable filters used for air pollution control, dust control, or powder control.

Almlie, Jay C; Miller, Stanley J

2014-11-11T23:59:59.000Z

300

Removal of Estrogenic Pollutants from Contaminated Water Using  

E-Print Network [OSTI]

Removal of Estrogenic Pollutants from Contaminated Water Using Molecularly Imprinted Polymers Z I H that this material may be appropriate for treating a complex mixture of estrogenic pollutants. The feasibility of removing estrogenic compounds from environmental water by the MIP was demonstrated using lake water spiked

Chen, Wilfred

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Potential Supply Impacts of Removal of 1-Pound RVP Waiver  

E-Print Network [OSTI]

by the Office of Oil and Gas of the Energy Information Administration. General questions concerning the report, Petroleum Division #12;1 Energy Information Administration/Potential Supply Impacts of Removal of 1-Pound;2 Energy Information Administration/Potential Supply Impacts of Removal of 1-Pound Waiver provides

Patzek, Tadeusz W.

302

Atmospheric Environment 41 (2007) 31513160 Ozone removal by HVAC filters  

E-Print Network [OSTI]

Atmospheric Environment 41 (2007) 3151­3160 Ozone removal by HVAC filters P. Zhao, J.A. Siegel�, R May 2006; accepted 14 June 2006 Abstract Residential and commercial HVAC filters that have been loaded of the relative importance of HVAC filters as a removal mechanism for ozone in residential and commercial

Siegel, Jeffrey

303

Process for selected gas oxide removal by radiofrequency catalysts  

DOE Patents [OSTI]

This process to remove gas oxides from flue gas utilizes adsorption on a char bed subsequently followed by radiofrequency catalysis enhancing such removal through selected reactions. Common gas oxides include SO[sub 2] and NO[sub x]. 1 figure.

Cha, C.Y.

1993-09-21T23:59:59.000Z

304

Aluminum Removal from Photographic Waste Submitted to Dr. Tony Bi  

E-Print Network [OSTI]

Aluminum Removal from Photographic Waste Submitted to Dr. Tony Bi By: Kristen Favel, Tiffany Jung, and Kenny Tam CHBE 484 University of British Columbia April 15, 2009 #12;ii "Aluminum Removal from photographic waste has shown elevated levels of aluminum in the fixer, which exceed sewer discharge standards

305

Fuzzy predictive control for nitrogen removal in biological wastewater treatment  

E-Print Network [OSTI]

Fuzzy predictive control for nitrogen removal in biological wastewater treatment S. Marsili wastewater is too low, full denitrification is difficult to obtain and an additional source of organic carbon predictive control; wastewater treatment plant Introduction The problem of improving the nitrogen removal

306

Continuous cryopump with a method for removal of solidified gases  

DOE Patents [OSTI]

An improved cryopump for the removal of gases from a high vacuum, comprising a cryopanel incorporating honeycomb structure, refrigerant means thermally connected to the cryopanel, and a rotatable channel moving azimuthally around an axis located near the center of the cryopanel, removing gases adsorbed within the honeycomb structure by subliming them and conducting them outside the vacuum vessel. 4 figs.

Carlson, L.W.; Herman, H.

1988-05-05T23:59:59.000Z

307

Method for removing chlorine compounds from hydrocarbon mixtures  

DOE Patents [OSTI]

A process for removing halide ions from a hydrocarbon feedstream containing halogenated hydrocarbons wherein the contaminated feedstock is contacted with a solution of a suitable oxidizing acid containing a lanthanide oxide, the acid being present in a concentration of at least about 50 weight percent for a time sufficient to remove substantially all of the halide ion from the hydrocarbon feedstock.

Janoski, E.J.; Hollstein, E.J.

1984-09-29T23:59:59.000Z

308

Microsoft PowerPoint - Town Bluff Vegetation impact.ppt  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces andMapping Richland OperationsU.S.OnlineTank09TWP-ICEPortland, Oregon

309

488-D Ash Basin Vegetative Cover Treatibility Study  

SciTech Connect (OSTI)

The 488-D Ash Basin is an unlined containment basin that received ash and coal reject material from the operation of a powerhouse at the USDOE's Savannah River Site, SC. They pyretic nature of the coal rejects has resulted in the formation of acidic drainage (AD), which has contributed to groundwater deterioration and threatens biota in down gradient wetlands. Establishment of a vegetative cover was examined as a remedial alternative for reducing AD generation within this system by enhanced utilization of rainwater and subsequent non-point source water pollution control. The low nutrient content, high acidity, and high salinity of the basin material, however, was deleterious to plant survivability. As such, studies to identify suitable plant species and potential adaptations, and pretreatment techniques in the form of amendments, tilling, and/or chemical stabilization were needed. A randomized block design consisting of three subsurface treatments (blocks) and five duplicated surface amendments (treatments) was developed. One hundred inoculated pine trees were planted on each plot. Herbaceous species were also planted on half of the plots in duplicated 1-m2 beds. After two growing seasons, deep ripping, subsurface amendments and surface covers were shown to be essential for the successful establishment of vegetation on the basin. This is the final report of the study.

Barton, Christopher; Marx, Don; Blake, John; Adriano, Domy; Koo, Bon-Jun; Czapka, Stephen

2003-01-01T23:59:59.000Z

310

Potential of vegetable oils as a domestic heating fuel  

SciTech Connect (OSTI)

The dependence on imported oil for domestic heating has led to the examination of other potential fuel substitutes. One potential fuel is some form of vegetable oil, which could be a yearly-renewable fuel. In Western Canada, canola has become a major oilseed crop; in Eastern Canada, sunflowers increasingly are becoming a source for a similar oil; for this reason, the Canadian Combustion Research Laboratory (CCRL) has chosen these oils for experimentation. Trials have been conducted in a conventional warm air oil furnace, fitted with a flame retention head burner. Performance has been measured with pure vegetable oils as well as a series of blends with conventional No. 2 oil. The effects of increased fuel pressure and fuel preheating are established. Emissions of carbon monoxide, nitrogen oxides, unburned hydrocarbons and particulates are given for both steady state and cyclic operation. Canola oil cannot be fired in cyclic operation above 50:50 blends with No. 2 oil. At any level above a 10% blend, canola is difficult to burn, even with significant increased pressure and temperature. Sunflower oil is much easier to burn and can be fired as a pure fuel, but with high emissions of incomplete combustion products. An optimum blend of 50:50 sunflower in No. 2 oil yields emissions and performance similar to No. 2 oil. This blend offers potential as a means of reducing demand of imported crude oil for domestic heating systems.

Hayden, A.C.S.; Begin, E.; Palmer, C.E.

1982-06-01T23:59:59.000Z

311

High Energy Laser for Space Debris Removal  

SciTech Connect (OSTI)

The National Ignition Facility (NIF) and Photon Science Directorate at Lawrence Livermore National Laboratory (LLNL) has substantial relevant experience in the construction of high energy lasers, and more recently in the development of advanced high average power solid state lasers. We are currently developing new concepts for advanced solid state laser drivers for the Laser Inertial Fusion Energy (LIFE) application, and other high average power laser applications that could become central technologies for use in space debris removal. The debris population most readily addressed by our laser technology is that of 0.1-10 cm sized debris in low earth orbit (LEO). In this application, a ground based laser system would engage an orbiting target and slow it down by ablating material from its surface which leads to reentry into the atmosphere, as proposed by NASA's ORION Project. The ORION concept of operations (CONOPS) is also described in general terms by Phipps. Key aspects of this approach include the need for high irradiance on target, 10{sup 8} to 10{sup 9} W/cm{sup 2}, which favors short (i.e., picoseconds to nanoseconds) laser pulse durations and high energy per pulse ({approx} > 10 kJ). Due to the target's orbital velocity, the potential duration of engagement is only of order 100 seconds, so a high pulse repetition rate is also essential. The laser technology needed for this application did not exist when ORION was first proposed, but today, a unique combination of emerging technologies could create a path to enable deployment in the near future. Our concepts for the laser system architecture are an extension of what was developed for the National Ignition Facility (NIF), combined with high repetition rate laser technology developed for Inertial Fusion Energy (IFE), and heat capacity laser technology developed for military applications. The 'front-end' seed pulse generator would be fiber-optics based, and would generate a temporally, and spectrally tailored pulse designed for high transmission through the atmosphere, as well as efficient ablative coupling to the target. The main amplifier would use either diode-pumped or flashlamp-pumped solid state gain media, depending on budget constraints of the project. A continuously operating system would use the gas-cooled amplifier technology developed for Mercury, while a burst-mode option would use the heat capacity laser technology. The ground-based system that we propose is capable of rapid engagement of targets whose orbits cross over the site, with potential for kill on a single pass. Very little target mass is ablated per pulse so the potential to create additional hazardous orbiting debris is minimal. Our cost estimates range from $2500 to $5000 per J depending on choices for laser gain medium, amplifier pump source, and thermal management method. A flashlamp-pumped, Nd:glass heat-capacity laser operating in the burst mode would have costs at the lower end of this spectrum and would suffice to demonstrate the efficacy of this approach as a prototype system. A diode-pumped, gas-cooled laser would have higher costs but could be operated continuously, and might be desirable for more demanding mission needs. Maneuverability can be incorporated in the system design if the additional cost is deemed acceptable. The laser system would need to be coupled with a target pointing and tracking telescope with guide-star-like wavefront correction capability.

Barty, C; Caird, J; Erlandson, A; Beach, R; Rubenchik, A

2009-10-30T23:59:59.000Z

312

Effect of Brush Vegetation on Deep Drainage Using Chloride Mass Balance  

E-Print Network [OSTI]

is comparable to that by herbaceous vegetation (Wilcox, 2005). The canopy of an average-size, mature redberry and ashe juniper can intercept 26% and 37% of the annual precipitation, respectively. Redberry and ashe juniper litter can intercept 40% and 43..., superactive, thermic Pachic Paleustolls. Dominant woody-shrub vegetation cover includes juniper (Juniperus ashei) with other existing vegetation such as little bluestem (Schizachyrium scoparium) and threeawn (Aristida). Site G4 The soil at site G4...

Navarrete Ganchozo, Ronald J.

2011-02-22T23:59:59.000Z

313

Vegetation of Upper Coastal Plain depression wetlands: Environmental templates and wetland dynamics within a landscape framework.  

SciTech Connect (OSTI)

Reference wetlands play an important role in efforts to protect wetlands and assess wetland condition. Because wetland vegetation integrates the influence of many ecological factors, a useful reference system would identify natural vegetation types and include models relating vegetation to important regional geomorphic, hydrologic, and geochemical properties. Across the U.S. Atlantic Coastal Plain, depression wetlands are a major hydrogeomorphic class with diverse characteristics. For 57 functional depression wetlands in the Upper Coastal Plain of South Carolina, we characterized the principal vegetation types and used a landscape framework to assess how local (wetland-level) factors and regional landscape settings potentially influence vegetation composition and dynamics. Wetland sites were stratified across three Upper Coastal Plain landscape settings that differ in soils, surface geology, topography, and land use. We sampled plant composition, measured relevant local variables, and analyzed historical transitions in vegetative cover types. Cluster analysis identified six vegetation types, ranging from open-water ponds and emergent marshes to closed forests. Significant vegetation-environment relationships suggested environmental ''templates'' for plant community development. Of all local factors examined, wetland hydrologic regime was most strongly correlated with vegetation type, but depression size, soil textural type, and disturbance history were also significant. Because hydrogeologic settings influence wetland features, local factors important to vegetation were partly predictable from landscape setting, and thus wetland types were distributed non-randomly across landscape settings. Analysis of long-term vegetation change indicated relative stability in some wetlands and succession in others. We developed a landscape-contingent model for vegetation dynamics, with hydroperiod and fire as major driving variables. The wetland classification, environmental templates, and dynamics model provide a reference framework to guide conservation priorities and suggest possible outcomes of restoration or management.

De Steven, Diane; Toner, Maureen, M.

2004-03-01T23:59:59.000Z

314

Massive Hanford Test Reactor Removed - Plutonium Recycle Test...  

Broader source: Energy.gov (indexed) [DOE]

challenge on the U.S. Department of Energy's (DOE) Hanford Site by removing a 1,082-ton nuclear test reactor from the 300 Area. The River Corridor is a 220-square-mile section of...

315

Reconvergent Fanout Removal Through Partial BIST Insertion Ian G. Harris  

E-Print Network [OSTI]

Reconvergent Fanout Removal Through Partial BIST Insertion Ian G. Harris Department of Electrical and Computer Engineering University of Massachusetts at Amherst E-mail: harris@ecs.umass.edu I. ABSTRACT

Harris, Ian G.

316

Method to remove uranium/vanadium contamination from groundwater  

DOE Patents [OSTI]

A process for removing uranium/vanadium-based contaminants from groundwater using a primary in-ground treatment media and a pretreatment media that chemically adjusts the groundwater contaminant to provide for optimum treatment by the primary treatment media.

Metzler, Donald R. (DeBeque, CO); Morrison, Stanley (Grand Junction, CO)

2004-07-27T23:59:59.000Z

317

Web Indexing on a Diet: Template Removal with the  

E-Print Network [OSTI]

April 2009 Web Indexing on a Diet: Template Removal with the Sandwich Algorithm Stephen Wan stephen.wan@csiro.au Paul Thomas paul.thomas@csiro.au Tom Rowlands tom.rowlands@csiro.au #12;Copyright and Disclaimer

Thomas, Paul

318

Removal of phenols from wastewater by soluble and immobilized tyrosinase  

SciTech Connect (OSTI)

An enzymatic method for removal of phenols from industrial wastewater was investigated. Phenols in an aqueous solution were removed after treatment with mushroom tyrosinase. The reduction order of substituted phenols is catechol > p-cresol > p-chlorophenol > phenol > p-methoxyphenol. In the treatment of tyrosinase alone, no precipitate was formed but a color change from colorless to dark-brown was observed. The colored products were removed by chitin and chitosan which are available abundantly as shellfish waste. In addition, the reduction rate of phenols was observed to be accelerated in the presence of chitosan. Tyrosinase, immobilized by using amino groups in the enzyme on cation exchange resins, can be used repeatedly. By treatment with immobilized tyrosinase, 100% of phenol was removed after 2 h, and the activity was reduced very little even after 10 repeat treatments.

Wada, Shinji; Ichikawa, Hiroyasu; Tatsumi, Kenji (National Inst. for Resources and Environment, Ibaraki (Japan))

1993-09-20T23:59:59.000Z

319

Considering removing "Show Preview" button on utility rate form...  

Open Energy Info (EERE)

Rmckeel's picture Submitted by Rmckeel(297) Contributor 22 April, 2013 - 13:55 Utility Rates I'm considering removing the "Show Preview" button, since it does not work (javascript...

320

Ozone Removal by Filters Containing Activated Carbon: A Pilot Study  

SciTech Connect (OSTI)

This study evaluated the ozone removal performance of moderate-cost particle filters containing activated carbon when installed in a commercial building heating, ventilating, and air conditioning (HVAC) system. Filters containing 300 g of activated carbon per 0.09 m2 of filter face area were installed in two 'experimental' filter banks within an office building located in Sacramento, CA. The ozone removal performance of the filters was assessed through periodic measurements of ozone concentrations in the air upstream and downstream of the filters. Ozone concentrations were also measured upstream and downstream of a 'reference' filter bank containing filters without any activated carbon. The filter banks with prefilters containing activated carbon were removing 60percent to 70percent of the ozone 67 and 81 days after filter installation. In contrast, there was negligible ozone removal by the reference filter bank without activated carbon.

Fisk, William; Spears, Mike; Sullivan, Douglas; Mendell, Mark

2009-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

aromatic hydrocarbon removal: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

contamination control 12;10 Transfer of Graphite to Supersack (V) 12;11 Moving graphite pile Complete shipment of graphite to DOE's Nevada Test Site Removal of biological shield...

322

acid dye removal: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

contamination control 12;10 Transfer of Graphite to Supersack (V) 12;11 Moving graphite pile Complete shipment of graphite to DOE's Nevada Test Site Removal of biological shield...

323

Membrane Based intensification of ammonia removal from wastewater  

E-Print Network [OSTI]

The aim of this research was to study a novel membrane based oxygen intensification system to enhance a biological wastewater treatment process for ammonia removal. Specifically, this work is concerned with the biological nitrification process which...

Almutairi, Azel

2011-12-31T23:59:59.000Z

324

Comparison of proton and neutron carrier removal rates  

SciTech Connect (OSTI)

Displacement damage induced carrier removal rates for proton irradiations in the energy range 10-175 MeV were compared to 1 MeV equivalent neutrons using power MOSFETs as a test vehicle. The results showed that, within experimental error, the degradation mechanisms were qualitatively similar and the ratio of proton to neutron carrier removal rates as a function of proton energy correlate with a calculation based on nonionization energy loss in silicon. For exposures under junction bias, p-type silicon was found to have a smaller carrier removal rate for both proton and neutron irradiations, whereas, for n-type silicon, junction bias had little effect on the carrier removal rate.

Pease, R.L.; Enlow, E.W.; Dinger, G.L.; Marshall, P.

1987-12-01T23:59:59.000Z

325

Method to Remove Uranium/Vanadium Contamination from Groundwater  

DOE Patents [OSTI]

A process for removing uranium/vanadium-based contaminants from groundwater using a primary in-ground treatment media and a pretreatment media that chemically adjusts the groundwater contaminant to provide for optimum treatment by the primary treatment media.

Metzler, Donald R.; Morrison Stanley

2004-07-27T23:59:59.000Z

326

Oil and Gas- Leases to remove or recover (Pennsylvania)  

Broader source: Energy.gov [DOE]

This act states that a lease or agreement conveying the right to remove or recover oil, natural gas or gas of any other designation from lessor to lessee shall not be valid if such lease does not...

327

Removal Rate Model for Magnetorheological Finishing of Glass  

SciTech Connect (OSTI)

Magnetorheological finishing (MRF) is a deterministic subaperture polishing process. The process uses a magntorheological (MR) fluid that consists of micrometer-sized, spherical, magnetic carbonyl iron (CI) particles, nonmagnetic polishing abrasives, water, and stabilizers. Material removal occurs when the CI and nonmagnetic polishing abrasives shear material off the surface being polished. We introduce a new MRF material removal rate model for glass. This model contains terms for the near surface mechanical properties of glass, drag force, polishing abrasive size and concentration, chemical durability of the glass, MR fluid pH, and the glass composition. We introduce quantitative chemical predictors for the first time, to the best of our knowledge, into an MRF removal rate model. We validate individual terms in our model separately and then combine all of the terms to show the whole MRF material removal model compared with experimental data. All of our experimental data were obtained using nanodiamond MR fluids and a set of six optical glasses.

DeGroote, J.E.; Marino, A.E.; WIlson, J.P.; Bishop, A.L.; Lambropoulos, J.C.; Jacobs, S.D.

2007-11-14T23:59:59.000Z

328

Nitrogen oxides removal by pulsed corona enhanced wet electrostatics precipitation  

SciTech Connect (OSTI)

This paper presents the results of a bench-scale pulsed-corona enhanced wet electrostatic precipitator (wESP) application for removal of nitrogen oxides. This wESP is designed to operate wet/dry, positive/negative, and pulsed/non-pulsed conditions. The applied pulsed voltage is varied from 0 to 60 kV at 70 Hz. Gas flow rate is a nominal 7 m{sup 3}/hr and the collecting electrode area is 0.20 m{sup 2}. A simulated flue gas with NO concentration up to 1,200 ppm{sub v} has been used to determine the feasibility of NO{sub x} removal in the wESP. NO has to be oxidized to N{sub 2} before any removal takes place. NO{sub x} removal efficiency increased with gas residence time, inlet NO concentration and applied corona power. In the air stream with 10 seconds gas residence time, up to 20% of 1,000 ppm NO (or 22% NO{sub x}) was removed from an air stream of 1.9x10{sup {minus}3} m{sup 3}/s with a water flow of 6.3 x 10{sup {minus}5} m{sup 3}/sec and 20 W, 70 Hz pulsed corona. Both ammonia and ozone injections improve the NO{sub x} removal for both the corona and non-corona cases. With the inclusion of NH{sub 3} (NH{sub 3}/NO{sub x} ratio 1.3) and 25 watts corona power, NO removal efficiency was increased from 28% to 57%. The amount of in-situ ozone is not enough to be considered as a major NO{sub x} removal mechanism in this wESP. However, the additional injection of ozone improves the NO removal from 29% to 38% for both the corona and non-corona cases. When the oxygen concentration is dropped to 3% in a simulated flue gas with 12% CO{sub 2} and 800 ppm NO and 70% relative humidity at 11.5 s of gas residence time, the removal efficiency of NO is only 5%. Adding NH{sub 3} (NH{sub 3}/NO{sub x} ratio 1) at 76 watts corona power, NO removal is increased to 13%.

Tseng, C.H.; Keener, T.C.; Khang, S.J.

1999-07-01T23:59:59.000Z

329

Vegetation Dynamics and Livestock Production on Rangelands in the Southern Great Plains.  

E-Print Network [OSTI]

??We examined vegetation dynamics and livestock production in response to land management practices on rangelands in two different studies, one in north central and one… (more)

Cummings, Daniel Chad

2007-01-01T23:59:59.000Z

330

E-Print Network 3.0 - anthropogenic vegetation fires Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

dust aerosols VOCsDMS ET vegetation Anthropogenic waste byproduct air quality water management... combustionfires Anthropogenic crop production oil byproduct drilling...

331

SITE DESIGN GUIDELINES PEDESTRIAN VEHICULAR BICYCLE VEGETATION FURNISHINGS LIGHTING SIGNAGE PAVING SITEWORK PARKING  

E-Print Network [OSTI]

SITE DESIGN GUIDELINES PEDESTRIAN VEHICULAR BICYCLE VEGETATION FURNISHINGS LIGHTING SIGNAGE PAVING.7 Pedestrians .................................................................................... 3.8 Bicycles ..................................................... Section Four Bicycle Systems 4.1 Shared Roadways

Duchowski, Andrew T.

332

Removal of deposited copper from nuclear steam generators  

SciTech Connect (OSTI)

A review of the copper-removal process implemented during the cleaning of the NPD nuclear steam generator in Ontario revealed that major shortcomings in the process were depletion of the strong ammonia solution and relatively poor copper removal. Tests have shown that the concentration of the ammonia solution can be preserved close to its initial value, and high concentrations of complexed copper obtained, by sparging the ammonia solution with oxygen recirculating through a gas recirculation loop. Using recirculating oxygen for sparging at ambient air temperature, approximately 11 g/l of copper were dissolved by 100 g/l ammonia solution while the gaseous ammonia content of the recirculating gas remained well below the lower flammability limit. The corrosion rates of mild steel and commonly used nuclear steam generator tube materials in oxygenated ammonia solution were less than 30 mil/yr and no intergranular attack of samples was observed during tests. A second technique studied for the removal of copper is to ammoniate the spent iron-removal solvent to approximately pH 9.5 and sparge with recirculating oxygen. Complexed ferric iron in the spent iron-removal solvent was found to be the major oxidizing agent for metallic copper. The ferric iron can be derived from oxidation of dissolved ferrous iron to the ferric state or from dissolved oxides of iron directly. To extract copper from the secondary sides of nuclear steam generators, strong ammonia solution sparged with recirculating oxygen is recommended as the first stage, while ammoniated spent iron-removal solvent sparged with recirculating oxygen may be used to remove the copper freshly exposed during the removal of iron.

McSweeney, P.

1982-05-01T23:59:59.000Z

333

Radiator debris removing apparatus and work machine using same  

DOE Patents [OSTI]

A radiator assembly includes a finned radiator core and a debris removing apparatus having a compressed air inlet and at least one compressed air outlet configured to direct compressed air through the radiator core. A work machine such as a wheel loader includes a radiator and a debris removing apparatus coupled with on-board compressed air and having at least one pressurized gas outlet configured to direct a gas toward the face of the radiator.

Martin, Kevin L. (Washburn, IL); Elliott, Dwight E. (Chillicothe, IL)

2008-09-02T23:59:59.000Z

334

Fluidized bed gasification ash reduction and removal process  

DOE Patents [OSTI]

In a fluidized bed gasification system an ash removal system to reduce the particulate ash to a maximum size or smaller, allow the ash to cool to a temperature lower than the gasifier and remove the ash from the gasifier system. The system consists of a crusher, a container containing level probes and a means for controlling the rotational speed of the crusher based on the level of ash within the container.

Schenone, Carl E. (Madison, PA); Rosinski, Joseph (Vanderbilt, PA)

1984-12-04T23:59:59.000Z

335

Fluidized bed gasification ash reduction and removal system  

DOE Patents [OSTI]

In a fluidized bed gasification system an ash removal system to reduce the particulate ash to a maximum size or smaller, allow the ash to cool to a temperature lower than the gasifier and remove the ash from the gasifier system. The system consists of a crusher, a container containing level probes and a means for controlling the rotational speed of the crusher based on the level of ash within the container.

Schenone, Carl E. (Madison, PA); Rosinski, Joseph (Vanderbilt, PA)

1984-02-28T23:59:59.000Z

336

Process for removing heavy metal compounds from heavy crude oil  

DOE Patents [OSTI]

A process is provided for removing heavy metal compounds from heavy crude oil by mixing the heavy crude oil with tar sand; preheating the mixture to a temperature of about 650.degree. F.; heating said mixture to up to 800.degree. F.; and separating tar sand from the light oils formed during said heating. The heavy metals removed from the heavy oils can be recovered from the spent sand for other uses.

Cha, Chang Y. (Golden, CO); Boysen, John E. (Laramie, WY); Branthaver, Jan F. (Laramie, WY)

1991-01-01T23:59:59.000Z

337

Solid materials for removing arsenic and method thereof  

SciTech Connect (OSTI)

Solid materials have been developed to remove arsenic compounds from aqueous media. The arsenic is removed by passing the aqueous phase through the solid materials which can be in molded, granular, or powder form. The solid materials adsorb the arsenic leaving a purified aqueous stream. The materials are aerogels or xerogels and aerogels or xerogels and solid support structure, e.g., granulated activated carbon (GAC), mixtures. The species-specific adsorption occurs through specific chemical modifications of the solids tailored towards arsenic.

Coronado, Paul R. (Livermore, CA); Coleman, Sabre J. (Oakland, CA); Sanner, Robert D. (Livermore, CA); Dias, Victoria L. (Livermore, CA); Reynolds, John G. (San Ramon, CA)

2010-09-28T23:59:59.000Z

338

Solid materials for removing arsenic and method thereof  

DOE Patents [OSTI]

Solid materials have been developed to remove arsenic compounds from aqueous media. The arsenic is removed by passing the aqueous phase through the solid materials which can be in molded, granular, or powder form. The solid materials adsorb the arsenic leaving a purified aqueous stream. The materials are aerogels or xerogels and aerogels or xerogels and solid support structure, e.g., granulated activated carbon (GAC), mixtures. The species-specific adsorption occurs through specific chemical modifications of the solids tailored towards arsenic.

Coronado, Paul R. (Livermore, CA); Coleman, Sabre J. (Oakland, CA); Sanner, Robert D. (Livermore, CA); Dias, Victoria L. (Livermore, CA); Reynolds, John G. (San Ramon, CA)

2008-07-01T23:59:59.000Z

339

Mercury and tritium removal from DOE waste oils  

SciTech Connect (OSTI)

This work covers the investigation of vacuum extraction as a means to remove tritiated contamination as well as the removal via sorption of dissolved mercury from contaminated oils. The radiation damage in oils from tritium causes production of hydrogen, methane, and low-molecular-weight hydrocarbons. When tritium gas is present in the oil, the tritium atom is incorporated into the formed hydrocarbons. The transformer industry measures gas content/composition of transformer oils as a diagnostic tool for the transformers` condition. The analytical approach (ASTM D3612-90) used for these measurements is vacuum extraction of all gases (H{sub 2}, N{sub 2}, O{sub 2}, CO, CO{sub 2}, etc.) followed by analysis of the evolved gas mixture. This extraction method will be adapted to remove dissolved gases (including tritium) from the SRS vacuum pump oil. It may be necessary to heat (60{degrees}C to 70{degrees}C) the oil during vacuum extraction to remove tritiated water. A method described in the procedures is a stripper column extraction, in which a carrier gas (argon) is used to remove dissolved gases from oil that is dispersed on high surface area beads. This method appears promising for scale-up as a treatment process, and a modified process is also being used as a dewatering technique by SD Myers, Inc. (a transformer consulting company) for transformers in the field by a mobile unit. Although some mercury may be removed during the vacuum extraction, the most common technique for removing mercury from oil is by using sulfur-impregnated activated carbon (SIAC). SIAC is currently being used by the petroleum industry to remove mercury from hydrocarbon mixtures, but the sorbent has not been previously tested on DOE vacuum oil waste. It is anticipated that a final process will be similar to technologies used by the petroleum industry and is comparable to ion exchange operations in large column-type reactors.

Klasson, E.T. [Oak Ridge National Lab., TN (United States)

1997-10-01T23:59:59.000Z

340

Modeling Sustainable Agricultural Residue Removal at the Subfield Scale  

SciTech Connect (OSTI)

This study developed a computational strategy that utilizes data inputs from multiple spatial scales to investigate how variability within individual fields can impact sustainable residue removal for bioenergy production. Sustainable use of agricultural residues for bioenergy production requires consideration of the important role that residues play in limiting soil erosion and maintaining soil C, health, and productivity. Increased availability of subfield-scale data sets such as grain yield data, high-fidelity digital elevation models, and soil characteristic data provides an opportunity to investigate the impacts of subfield-scale variability on sustainable agricultural residue removal. Using three representative fields in Iowa, this study contrasted the results of current NRCS conservation management planning analysis with subfield-scale analysis for rake-and-bale removal of agricultural residue. The results of the comparison show that the field-average assumptions used in NRCS conservation management planning may lead to unsustainable residue removal decisions for significant portions of some fields. This highlights the need for additional research on subfield-scale sustainable agricultural residue removal including the development of real-time variable removal technologies for agricultural residue.

Muth, D.J.; McCorkle, D.S.; Koch, J.B.; Bryden, K.M.

2012-05-02T23:59:59.000Z

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Toward a mechanistic modeling of nitrogen limitation on vegetation dynamics  

SciTech Connect (OSTI)

Nitrogen is a dominant regulator of vegetation dynamics, net primary production, and terrestrial carbon cycles; however, most ecosystem models use a rather simplistic relationship between leaf nitrogen content and photosynthetic capacity. Such an approach does not consider how patterns of nitrogen allocation may change with differences in light intensity, growing-season temperature and CO{sub 2} concentration. To account for this known variability in nitrogen-photosynthesis relationships, we develop a mechanistic nitrogen allocation model based on a trade-off of nitrogen allocated between growth and storage, and an optimization of nitrogen allocated among light capture, electron transport, carboxylation, and respiration. The developed model is able to predict the acclimation of photosynthetic capacity to changes in CO{sub 2} concentration, temperature, and radiation when evaluated against published data of V{sub c,max} (maximum carboxylation rate) and J{sub max} (maximum electron transport rate). A sensitivity analysis of the model for herbaceous plants, deciduous and evergreen trees implies that elevated CO{sub 2} concentrations lead to lower allocation of nitrogen to carboxylation but higher allocation to storage. Higher growing-season temperatures cause lower allocation of nitrogen to carboxylation, due to higher nitrogen requirements for light capture pigments and for storage. Lower levels of radiation have a much stronger effect on allocation of nitrogen to carboxylation for herbaceous plants than for trees, resulting from higher nitrogen requirements for light capture for herbaceous plants. As far as we know, this is the first model of complete nitrogen allocation that simultaneously considers nitrogen allocation to light capture, electron transport, carboxylation, respiration and storage, and the responses of each to altered environmental conditions. We expect this model could potentially improve our confidence in simulations of carbon-nitrogen interactions and the vegetation feedbacks to climate in Earth system models.

Xu, Chonggang [Los Alamos National Laboratory (LANL); Fisher, Rosie [National Center for Atmospheric Research (NCAR); Wullschleger, Stan D [ORNL; Wilson, Cathy [Los Alamos National Laboratory (LANL); Cai, Michael [Los Alamos National Laboratory (LANL); McDowell, Nathan [Los Alamos National Laboratory (LANL)

2012-01-01T23:59:59.000Z

342

-Climate and pH as determinants of vegetation succession in man-made habitats -701 Journal of Vegetation Science 18: 701-710, 2007  

E-Print Network [OSTI]

sites in areas deforested by air pollution. Methods: We investigated vegetation patterns on 15 succes, spoil heaps after coal mining, sites at water reservoirs, extracted sand pit and peatland and reclaimed

KratochvĂ­l, Lukas

343

Mapping swamp timothy (Cripsis schenoides) seed productivity using spectral values and vegetation indices in managed wetlands  

SciTech Connect (OSTI)

This work examines the potential to predict the seed productivity of a key wetland plant species using spectral reflectance values and spectral vegetation indices. Specifically, the seed productivity of swamp timothy (Cripsis schenoides) was investigated in two wetland ponds, managed for waterfowl habitat, in California's San Joaquin Valley. Spectral reflectance values were obtained and associated spectral vegetation indices (SVI) calculated from two sets of high resolution aerial images (May 11, 2006 and June 9, 2006) and were compared to the collected vegetation data. Vegetation data were collected and analyzed from 156 plots for total aboveground biomass, total aboveground swamp timothy biomass, and total swamp timothy seed biomass. The SVI investigated included the Simple Ratio (SR), Normalized Difference Vegetation Index (NDVI), Soil Adjusted Vegetation Index (SAVI), Transformed Soil Adjusted Vegetation Index (TSAVI), Modified Soil Adjusted Vegetation Index (MSAVI), and Global Environment Monitoring Index (GEMI). We evaluated the correlation of the various SVI with in situ vegetation measurements for linear, quadratic, exponential and power functions. In all cases, the June image provided better predictive capacity relative to May, a result that underscores the importance of timing imagery to coincide with more favorable vegetation maturity. The north pond with the June image using SR and the exponential function (R{sup 2}=0.603) proved to be the best predictor of swamp timothy seed productivity. The June image for the south pond was less predictive, with TSAVI and the exponential function providing the best correlation (R{sup 2}=0.448). This result was attributed to insufficient vegetal cover in the south pond (or a higher percentage of bare soil) due to poor drainage conditions which resulted in a delay in swamp timothy germination. The results of this work suggest that spectral reflectance can be used to estimate seed productivity in managed seasonal wetlands.

Rahilly, P.J.A.; Li, D.; Guo, Q.; Zhu, J.; Ortega, R.; Quinn, N.W.T.; Harmon, T.C.

2010-01-15T23:59:59.000Z

344

Evaluation of the Hydro-Thermodynamic Soil Vegetation Scheme and implementation of a new numerical scheme  

E-Print Network [OSTI]

ii Evaluation of the Hydro-Thermodynamic Soil Vegetation Scheme and implementation of a new.S. Fairbanks, Alaska August 2005 #12;iii Abstract The Hydro-Thermodynamic Soil-Vegetation Scheme (HTSVS........................................................................................................................... 24 Evaluation of snow depth and soil temperatures predicted by the Hydro- Thermodynamic Soil

Moelders, Nicole

345

Arctic Region Evaluation of the Hydro-Thermodynamic Soil Vegetation Scheme (HTSVS)  

E-Print Network [OSTI]

Arctic Region Evaluation of the Hydro-Thermodynamic Soil Vegetation Scheme (HTSVS) Pamela Spier, University of Alaska, Fairbanks, AK Abstract This paper presents an evaluation of the Hydro. Introduction and Motivation The Hydro-Thermodynamic Soil Vegetation Scheme (HTSVS, Kramm et al. 1996, Mölders

Moelders, Nicole

346

Comparing Optical and Microwave Remote Sensing-based Vegetation Density over Mongolia for 1988-2006  

E-Print Network [OSTI]

Vegetation Index (NDVI), derived from the Advanced Very High Resolution Radiometer (AVHRR) series.vandijk@csiro.au Abstract ­ Vegetation density plays an important role in water and energy balance. Satellite-based optical product (Tucker et al., 2005). It can provide a relatively high spatial resolution product (up to 1km

Evans, Jason

347

Shrub thicket vegetation on tropical granitic inselbergs (French Guiana) Sarthou, Corinne1*  

E-Print Network [OSTI]

1 Shrub thicket vegetation on tropical granitic inselbergs (French Guiana) Sarthou, Corinne1@mnhn.fr Abstract. In French Guiana, inselbergs are granite outcrops rising abruptly from the surrounding rain substrate. Shrub granitic vegetation, organised in thickets on open exposed rocks of inselbergs

Paris-Sud XI, Université de

348

Effects of forestry practices on vegetation structure and bird community of Kibale National Park, Uganda  

E-Print Network [OSTI]

, Uganda Cagan H. Sekercioglu* Center for Conservation Biology, Department of Biological Sciences, Stanford on the vegetation structure and bird community of Kibale National Park, Uganda. I compared four forest treatments Ltd. All rights reserved. Keywords: Uganda; Tropical forestry; Selective logging; Vegetation structure

Sekercioglu, Cagan Hakki

349

P.M. Vermeersch (ed.) 3 -WOODY VEGETATION AND ITS USE DURING THE NEOLITHIC AT  

E-Print Network [OSTI]

because they have been submitted for 14 C dating. The site is located in a tributary wadi of the wadi). The modern arboreal vegetation of the Tree Shelter wadi is limited to a lonely Acacia tree at the en- trance of the wadi. The modern vegetation in the broad area of the Red Sea coastal land between wadi Qena

Marinova, Elena

350

Impacts of vegetation and cold season processes on soil moisture and climate relationships over Eurasia  

E-Print Network [OSTI]

Impacts of vegetation and cold season processes on soil moisture and climate relationships over investigate the impacts of vegetation and cold season processes on soil moisture persistence and climate, without the use of a model, in the former Soviet Union provides a unique look at soil moisture­climate

Ni-Meister, Wenge

351

Climate, Livestock, and Vegetation: What Drives Fire Increase in the Arid  

E-Print Network [OSTI]

: burning; arid ecosystems; livestock; climate; broad-scale climate; Southern Russia; socio-economic change by decreasing livestock numbers, vegetation changes, climate change, or interactions of these factors. OurClimate, Livestock, and Vegetation: What Drives Fire Increase in the Arid Ecosystems of Southern

Radeloff, Volker C.

352

A TEST FOR LIFE ON EXOPLANETS: THE TERRESTRIAL VEGETATION DETECTION IN THE EARTHSHINE SPECTRUM  

E-Print Network [OSTI]

bacteria [7]. A second type of biosignature is provided by signs of stellar light transformation the possible presence of life on this planet. Spectral biosignatures can be of two types. A first type consists of photosynthetic (green) vegetation, non­photosynthetic (dry) and a soil (from [9]). The so­called vegetation red

Lardière, Olivier

353

Organic Vegetable Organic Vegetable  

E-Print Network [OSTI]

concentrates on natural processes and how to manage them. Other materials and products are additions to .......................................6 Safety ................................................................6 Insect Management ...........................................7 Disease Management ......................................10 Weed Management

354

A struggle for Cherokee community : excavating identity in post-removal North Carolina.  

E-Print Network [OSTI]

??The Cherokee Removal of 1838 was intended to remove all members of the Cherokee Nation to west of the Mississippi River. However, a small number… (more)

Greene, Lance.

2009-01-01T23:59:59.000Z

355

Removable pellicle for lithographic mask protection and handling  

DOE Patents [OSTI]

A removable pellicle for a lithographic mask that provides active and robust particle protection, and which utilizes a traditional pellicle and two deployments of thermophoretic protection to keep particles off the mask. The removable pellicle is removably attached via a retaining structure to the mask substrate by magnetic attraction with either contacting or non-contacting magnetic capture mechanisms. The pellicle retaining structural is composed of an anchor piece secured to the mask substrate and a frame member containing a pellicle. The anchor piece and the frame member are in removable contact or non-contact by the magnetic capture or latching mechanism. In one embodiment, the frame member is retained in a floating (non-contact) relation to the anchor piece by magnetic levitation. The frame member and the anchor piece are provided with thermophoretic fins which are interdigitated to prevent particles from reaching the patterned area of the mask. Also, the anchor piece and mask are maintained at a higher temperature than the frame member and pellicle which also prevents particles from reaching the patterned mask area by thermophoresis. The pellicle can be positioned over the mask to provide particle protection during mask handling, inspection, and pumpdown, but which can be removed manually or robotically for lithographic use of the mask.

Klebanoff, Leonard E. (Dublin, CA); Rader, Daniel J. (Albuquerque, NM); Hector, Scott D. (Oakland, CA); Nguyen, Khanh B. (Sunnyvale, CA); Stulen, Richard H. (Livermore, CA)

2002-01-01T23:59:59.000Z

356

VEGETATION COVER ANALYSIS OF HAZARDOUS WASTE SITES IN UTAH AND ARIZONA USING HYPERSPECTRAL REMOTE SENSING  

SciTech Connect (OSTI)

Remote sensing technology can provide a cost-effective tool for monitoring hazardous waste sites. This study investigated the usability of HyMap airborne hyperspectral remote sensing data (126 bands at 2.3 x 2.3 m spatial resolution) to characterize the vegetation at U.S. Department of Energy uranium processing sites near Monticello, Utah and Monument Valley, Arizona. Grass and shrub species were mixed on an engineered disposal cell cover at the Monticello site while shrub species were dominant in the phytoremediation plantings at the Monument Valley site. The specific objectives of this study were to: (1) estimate leaf-area-index (LAI) of the vegetation using three different methods (i.e., vegetation indices, red-edge positioning (REP), and machine learning regression trees), and (2) map the vegetation cover using machine learning decision trees based on either the scaled reflectance data or mixture tuned matched filtering (MTMF)-derived metrics and vegetation indices. Regression trees resulted in the best calibration performance of LAI estimation (R{sup 2} > 0.80). The use of REPs failed to accurately predict LAI (R{sup 2} < 0.2). The use of the MTMF-derived metrics (matched filter scores and infeasibility) and a range of vegetation indices in decision trees improved the vegetation mapping when compared to the decision tree classification using just the scaled reflectance. Results suggest that hyperspectral imagery are useful for characterizing biophysical characteristics (LAI) and vegetation cover on capped hazardous waste sites. However, it is believed that the vegetation mapping would benefit from the use of 1 higher spatial resolution hyperspectral data due to the small size of many of the vegetation patches (< 1m) found on the sites.

Serrato, M.; Jungho, I.; Jensen, J.; Jensen, R.; Gladden, J.; Waugh, J.

2012-01-17T23:59:59.000Z

357

Removal of impurities from dry scrubbed fluoride enriched alumina  

SciTech Connect (OSTI)

The pot-gas from an aluminum electrolytic cell is cleaned by a dry scrubbing process using fresh alumina as a scrubbing agent. This alumina is enriched with fluorides and trace impurities in a closed loop system with the pots. The only significant removal of the impurities is due to metal tapping. An improved technique has been developed that is more effective than earlier stripper systems. The impurity-rich fine fraction (< 10 {micro}m) of the enriched alumina is partly attached to the coarser alumina. That attachment has to be broken. Selective impact milling under special moderate conditions and air classifying have shown to be a cost effective process for the removal of impurities. For iron (Fe) and phosphorus (P) about 30--70% can be removed by the separation of 0.5--1% of the alumina. Full scale tests have successfully confirmed these results.

Schuh, L. [ABB Corporate Research Center, Heidelberg (Germany); Wedde, G. [ABB Environmental, Oslo (Norway)

1996-10-01T23:59:59.000Z

358

Mobile system for microwave removal of concrete surfaces  

DOE Patents [OSTI]

A method and apparatus are disclosed for the microwave removal of contaminated concrete surfaces. The apparatus comprises a housing adapted to pass over a support surface. The housing includes a waveguide for directing microwave energy to the surface at an angle maximizing absorption of microwave energy by the surface. The apparatus is further provided with a source of microwave energy operably associated with the waveguide, wherein the microwave energy has a frequency of between about 10.6 GHz and about 24 GHz and acts to remove the uppermost layer from the surface. The apparatus further includes a debris containment assembly comprising a vacuum assembly operably associated with the housing. The vacuum assembly is adapted to remove debris from the area adjacent the surface. 7 figs.

White, T.L.; Bigelow, T.S.; Schaich, C.R.; Foster, D. Jr.

1997-06-03T23:59:59.000Z

359

Metal chelate process to remove pollutants from fluids  

DOE Patents [OSTI]

The present invention relates to improved methods using an organic iron chelate to remove pollutants from fluids, such as flue gas. Specifically, the present invention relates to a process to remove NO[sub x] and optionally SO[sub 2] from a fluid using a metal ion (Fe[sup 2+]) chelate wherein the ligand is a dimercapto compound wherein the --SH groups are attached to adjacent carbon atoms (HS--C--C--SH) or (SH--C--CCSH) and contain a polar functional group so that the ligand of DMC chelate is water soluble. Alternatively, the DMC is covalently attached to a water insoluble substrate such as a polymer or resin, e.g., polystyrene. The chelate is regenerated using electroreduction or a chemical additive. The dimercapto compound bonded to a water insoluble substrate is also useful to lower the concentration or remove hazardous metal ions from an aqueous solution. 26 figures.

Chang, S.G.T.

1994-12-06T23:59:59.000Z

360

Removal of fluoride impurities from UF/sub 6/ gas  

DOE Patents [OSTI]

A method of purifying a UF/sub 6/ gas stream containing one or more metal fluoride impurities composed of a transuranic metal, transition metal or mixtures thereof, is carried out by contacting the gas stream with a bed of UF/sub 5/ in a reaction vessel under conditions where at least one impurity reacts with the UF/sub 5/ to form a nongaseous product and a treated gas stream, and removing the treated gas stream from contact with the bed. The nongaseous products are subsequently removed in a reaction with an active fluorine affording agent to form a gaseous impurity which is removed from the reaction vessel. The bed of UF/sub 5/ is formed by the reduction of UF/sub 6/ in the presence of uv light. One embodiment of the reaction vessel includes a plurality of uv light sources as tubes on which UF/sub 5/ is formed. 2 figures.

Beitz, J.V.

1984-01-06T23:59:59.000Z

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Mobile system for microwave removal of concrete surfaces  

DOE Patents [OSTI]

A method and apparatus for the microwave removal of contaminated concrete surfaces. The apparatus comprises a housing adapted to pass over a support surface. The housing includes a waveguide for directing microwave energy to the surface at an angle maximizing absorption of microwave energy by the surface. The apparatus is further provided with a source of microwave energy operably associated with the waveguide, wherein the microwave energy has a frequency of between about 10.6 GHz and about 24 GHz and acts to remove the uppermost layer from the surface. The apparatus further includes a debris containment assembly comprising a vacuum assembly operably associated with the housing. The vacuum assembly is adapted to remove debris from the area adjacent the surface.

White, Terry L. (Oak Ridge, TN); Bigelow, Timothy S. (Knoxville, TN); Schaich, Charles R. (Lenoir City, TN); Foster, Jr., Don (Knoxville, TN)

1997-01-01T23:59:59.000Z

362

Removal of pollutants from solid matrices using supercritical fluids  

SciTech Connect (OSTI)

Several supercritical fluid extraction (SCFE) processes have been proposed for removing toxic and intractable organic compounds from a range of contaminated solids. These include soil remediation and the regeneration of absorbents used to treat wastewater streams such as granular activated carbon (GAC). As a separation technique for environmental control, SCFR has several distinct advantages over conventional liquid extraction methods and incineration. Most notably, the contaminant is removed from the solvent in a concentrated form via a change in pressure or temperature and can be completely separated upon expansion to atmospheric pressure. The viability of SCFE hinges on process conditions such as solvent-feed ratio and solvent recycle ratio. The necessity of recycling solvent complicates the contaminant separation step since a complete reduction to atmospheric pressure would create large recompression costs. Because of this, the pressure and temperature dependence of contaminant solubility must be understood so that operating conditions for the separation step can be defined. Fortunately, this is the most developed aspect of SCF technology. However, the mass transfer limitations to removing contaminants from solids change with solvent flow rate. This paper discusses the use of SCFE for environmental control and presents results for the removal of DDT and 2-chlorophenol from GAC. 2-chlorophenol is almost completely removed with pure CO{sub 2} at 40{degrees}C and 101 bar while only 55% of the DDT is removed at 40{degrees}C and 200 bar. These differences in regeneration efficiency cannot be understood solely in terms of solubility but point to a need for detailed studies of adsorption equilibrium and mass transfer resistances in supercritical fluid systems.

Tomasko, D.L. [Ohio State Univ., Columbus, OH (United States); Macnaughton, S.J.; Foster, N.R. [Univ. of South Wales, Kensington (Australia)] [and others

1995-04-01T23:59:59.000Z

363

Method for removal of furfural coke from metal surfaces  

SciTech Connect (OSTI)

This patent describes a process for preparing furfural coke for removal from metallic surfaces. It comprises: heating ship furfural coke without causing an evolution of heat capable of undesirably altering metallurgical properties of the surfaces in the presence of a gas with a total pressure of less than 100 psig containing molecular oxygen. The gas being at a sufficient temperature below 800{degrees}F. (427{degrees}C.) for a sufficient time to change the crush strength of the coke so as to permit removal with a water jet at a pressure of about 5000 psi.

Turner, J.D.

1990-02-27T23:59:59.000Z

364

Sorbents for the oxidation and removal of mercury  

DOE Patents [OSTI]

A promoted activated carbon sorbent is described that is highly effective for the removal of mercury from flue gas streams. The sorbent comprises a new modified carbon form containing reactive forms of halogen and halides. Optional components may be added to increase reactivity and mercury capacity. These may be added directly with the sorbent, or to the flue gas to enhance sorbent performance and/or mercury capture. Mercury removal efficiencies obtained exceed conventional methods. The sorbent can be regenerated and reused. Sorbent treatment and preparation methods are also described. New methods for in-flight preparation, introduction, and control of the active sorbent into the mercury contaminated gas stream are described.

Olson, Edwin S.; Holmes, Michael J.; Pavlish, John Henry

2014-09-02T23:59:59.000Z

365

Sorbents for the oxidation and removal of mercury  

DOE Patents [OSTI]

A promoted activated carbon sorbent is described that is highly effective for the removal of mercury from flue gas streams. The sorbent comprises a new modified carbon form containing reactive forms of halogen and halides. Optional components may be added to increase reactivity and mercury capacity. These may be added directly with the sorbent, or to the flue gas to enhance sorbent performance and/or mercury capture. Mercury removal efficiencies obtained exceed conventional methods. The sorbent can be regenerated and reused. Sorbent treatment and preparation methods are also described. New methods for in-flight preparation, introduction, and control of the active sorbent into the mercury contaminated gas stream are described.

Olson, Edwin S. (Grand Forks, ND); Holmes, Michael J. (Thompson, ND); Pavlish, John H. (East Grand Forks, MN)

2008-10-14T23:59:59.000Z

366

Sorbents for the oxidation and removal of mercury  

DOE Patents [OSTI]

A promoted activated carbon sorbent is described that is highly effective for the removal of mercury from flue gas streams. The sorbent comprises a new modified carbon form containing reactive forms of halogen and halides. Optional components may be added to increase reactivity and mercury capacity. These may be added directly with the sorbent, or to the flue gas to enhance sorbent performance and/or mercury capture. Mercury removal efficiencies obtained exceed conventional methods. The sorbent can be regenerated and reused. Sorbent treatment and preparation methods are also described. New methods for in-flight preparation, introduction, and control of the active sorbent into the mercury contaminated gas stream are described.

Olson, Edwin S. (Grand Forks, ND); Holmes, Michael J. (Thompson, ND); Pavlish, John H. (East Grand Forks, MN)

2012-05-01T23:59:59.000Z

367

Method for removal of beryllium contamination from an article  

DOE Patents [OSTI]

A method of removal of beryllium contamination from an article is disclosed. The method typically involves dissolving polyisobutylene in a solvent such as hexane to form a tackifier solution, soaking the substrate in the tackifier to produce a preform, and then drying the preform to produce the cleaning medium. The cleaning media are typically used dry, without any liquid cleaning agent to rub the surface of the article and remove the beryllium contamination below a non-detect level. In some embodiments no detectible residue is transferred from the cleaning wipe to the article as a result of the cleaning process.

Simandl, Ronald F.; Hollenbeck, Scott M.

2012-12-25T23:59:59.000Z

368

Water Recycling removal using temperature-sensitive hydronen  

SciTech Connect (OSTI)

The overall objective of this project was to study the proposed Water Recycling/Removal Using Temperature-Sensitive Hydrogels. The main element of this technology is the design of a suitable hydrogel that can perform needed water separation for pulp and paper industry. The specific topics studied are to answer following questions: (a) Can water be removed using hydrogel from large molecules such as lignin? (b) Can the rate of separation be made faster? (c) What are the molecular interactions with hydrogel surface? (d) Can a hydrogel be designed for a high ionic strength and high temperature? Summary of the specific results are given.

Rana B. Gupta

2002-10-30T23:59:59.000Z

369

Method for removing undesired particles from gas streams  

DOE Patents [OSTI]

The present invention discloses a process for removing undesired particles from a gas stream including the steps of contacting a composition containing an adhesive with the gas stream; collecting the undesired particles and adhesive on a collection surface to form an aggregate comprising the adhesive and undesired particles on the collection surface; and removing the agglomerate from the collection zone. The composition may then be atomized and injected into the gas stream. The composition may include a liquid that vaporizes in the gas stream. After the liquid vaporizes, adhesive particles are entrained in the gas stream. The process may be applied to electrostatic precipitators and filtration systems to improve undesired particle collection efficiency.

Durham, Michael Dean (Castle Rock, CO); Schlager, Richard John (Aurora, CO); Ebner, Timothy George (Westminster, CO); Stewart, Robin Michele (Arvada, CO); Hyatt, David E. (Denver, CO); Bustard, Cynthia Jean (Littleton, CO); Sjostrom, Sharon (Denver, CO)

1998-01-01T23:59:59.000Z

370

Compositions and methods for removing arsenic in water  

DOE Patents [OSTI]

Compositions and methods and for contaminants from water are provided. The compositions comprise ferric hydroxide and ferric oxyhydride coated substrates for use in removing the contaminant from the water. Contacting water bearing the contaminant with the substrates can substantially reduce contaminant levels therein. Methods of oxidizing the contaminants in water to facilitate their removal by the ferric hydroxide and ferric oxyhydride coated substrates are also provided. The contaminants include, but are not limited to, arsenic, selenium, uranium, lead, cadmium, nickel, copper, zinc, chromium and vanadium, their oxides and soluble salts thereof.

Gadgil, Ashok Jagannth (El Cerrito, CA)

2011-02-22T23:59:59.000Z

371

Method for the removal and recovery of mercury  

DOE Patents [OSTI]

The present invention is an enhanced method for the removal and recovery of mercury from mercury-contaminated matrices. The method involves contacting a mercury-contaminated matrix with an aqueous dispersant solution derived from specific intra-amoebic isolates to release the mercury from the mercury-contaminated matrix and emulsify the mercury; then, contacting the matrix with an amalgamating metal from a metal source to amalgamate the mercury to the amalgamating metal; removing the metallic source from the mercury-contaminated matrix; and heating the metallic source to vaporize the mercury in a closed system to capture the mercury vapors.

Easterly, C.E.; Vass, A.A.; Tyndall, R.L.

1997-01-28T23:59:59.000Z

372

Method for the removal and recovery of mercury  

DOE Patents [OSTI]

The present invention is an enhanced method for the removal and recovery of mercury from mercury-contaminated matrices. The method involves contacting a mercury-contaminated matrix with an aqueous dispersant solution derived from specific intra-amoebic isolates to release the mercury from the mercury-contaminated matrix and emulsify the mercury; then, contacting the matrix with an amalgamating metal from a metal source to amalgamate the mercury to the amalgamating metal; removing the metallic source from the mercury-contaminated matrix; and heating the metallic source to vaporize the mercury in a closed system to capture the mercury vapors.

Easterly, Clay E. (Knoxville, TN); Vass, Arpad A. (Oak Ridge, TN); Tyndall, Richard L. (Clinton, TN)

1997-01-01T23:59:59.000Z

373

Methods of hydrotreating a liquid stream to remove clogging compounds  

DOE Patents [OSTI]

A method includes producing formation fluid from a subsurface in situ heat treatment process. The formation fluid is separated to produce a liquid stream and a gas stream. At least a portion of the liquid stream is provided to a hydrotreating unit. At least a portion of selected in situ heat treatment clogging compositions in the liquid stream are removed to produce a hydrotreated liquid stream by hydrotreating at least a portion of the liquid stream at conditions sufficient to remove the selected in situ heat treatment clogging compositions.

Minderhoud, Johannes Kornelis [Amsterdam, NL; Nelson, Richard Gene [Katy, TX; Roes, Augustinus Wilhelmus Maria [Houston, TX; Ryan, Robert Charles [Houston, TX; Nair, Vijay [Katy, TX

2009-09-22T23:59:59.000Z

374

The impact of cattle grazing on salt marsh and elevated hummock vegetation communities of a Texas barrier island  

E-Print Network [OSTI]

To assess the effects of cattle herbivory on vegetation community structure and composition in a Texas coastal salt marsh, data measuring several vegetation parameters were collected in four distinct habitats within a heavily grazed marsh over...

Carothers, James Michael

2002-01-01T23:59:59.000Z

375

Use of vegetation for abatement of road traffic noise in a 1:10 scale street model  

E-Print Network [OSTI]

Use of vegetation for abatement of road traffic noise in a 1:10 scale street model J.Y. Jeona , H was constructed to evaluate the noise abatement by use of vegetation as sustainable means. The model materials

Paris-Sud XI, Université de

376

Fruit and Vegetable Servings in Local Farm-Sourced and Standard Lunches Offered to Children in a Head Start Program  

E-Print Network [OSTI]

. Independent-samples t-tests were performed using SPSS. There were no significant differences in either fruit or vegetable consumption between conventional lunches and locally-sourced lunches. Even though there was more variety of fruit and vegetable offerings...

Johnson, Amy M.

2010-04-25T23:59:59.000Z

377

Investigation of the effect of a circular patch of vegetation on turbulence generation and sediment deposition using four case studies  

E-Print Network [OSTI]

This study describes the spatial distribution of sediment deposition in the wake of a circular patch of model vegetation and the effect of the patch on turbulence and mean flow. Two difference types pf vegetation were used ...

Ortiz, Alejandra C

2012-01-01T23:59:59.000Z

378

Trajectories of change in sagebrush steppe vegetation communities in relation to multiple wildfires  

SciTech Connect (OSTI)

Repeated perturbations, both biotic and abiotic, can lead to fundamental changes in the nature of ecosystems including changes in state. Sagebrush-steppe communities provide important habitat for wildlife and grazing for livestock. Fire is an integral part of these systems, but there is concern that increased ignition frequencies and invasive species are fundamentally altering these systems. Despite these issues, the majority of studies of fire effects in Artemisia tridentata wyomingensis-dominated systems have focused on the effects of single burns. The Arid Lands Ecology Reserve (ALE), in south-central Washington (U.S.A.), was one of the largest areas of continuous shrub-steppe habitat in the state until large wildfires burnt the majority of it in 2000 and 2007. We analysed data from permanent vegetation transects established in 1996 and resampled in 2002 and 2009. Our objective was to describe how the fires, and subsequent post-fire restoration efforts, affected communities successional pathways. Plant communities differed in response to repeated fire and restoration; these differences could largely be ascribed to the functional traits of the dominant species. Low elevation communities, previously dominated by obligate seeders, moved farthest from their initial composition and were dominated by weedy, early successional species in 2009. Higher elevation sites with resprouting shrubs, native bunchgrasses and few invasive species were generally more resilient to the effects of repeated disturbances. Shrub cover has been almost entirely removed from ALE, though there is evidence of recovery where communities were dominated by re-sprouters. Cheatgrass (Bromus tectorum) dominance was reduced by herbicide application in areas where it was previously abundant but increased significantly in untreated areas. Several re-sprouting species, notably Phlox longifolia and Poa secunda, expanded remarkably following competitive release from shrub canopies and/or abundant cheatgrass. Our results suggest that community dynamics can be understood through a state-and-transition model with two axes (shrub/grass and native/invasive abundance), though such models also need to account for differences in plant functional traits and disturbance regimes. We use our results to develop an illustrative model that will be expanded with further research.

Davies, G. M.; Bakker, J. D.; Dettweiler-Robinson, E.; Dunwiddie, Peter W.; Hall, S. A.; Downs, Janelle L.; Evans, J.

2012-07-01T23:59:59.000Z

379

CX-012087: Categorical Exclusion Determination  

Broader source: Energy.gov [DOE]

Liberty Substation - Vegetation Management CX(s) Applied: B1.3 Date: 04/01/2014 Location(s): Arizona, Arizona Offices(s): Western Area Power Administration-Desert Southwest Region

380

CX-011480: Categorical Exclusion Determination  

Broader source: Energy.gov [DOE]

Vegetative Response to Metal Exposure in a Growing Media CX(s) Applied: B3.6 Date: 11/07/2013 Location(s): South Carolina Offices(s): Savannah River Operations Office

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

CX-008645: Categorical Exclusion Determination  

Broader source: Energy.gov [DOE]

Vegetative Response to Metal Exposure in a Growing Media CX(s) Applied: B3.6 Date: 05/22/2012 Location(s): South Carolina Offices(s): Savannah River Operations Office

382

CX-008634: Categorical Exclusion Determination  

Broader source: Energy.gov [DOE]

Vegetative Response to Metal Exposure in a Growing Media CX(s) Applied: B3.6 Date: 05/31/2012 Location(s): South Carolina Offices(s): Savannah River Operations Office

383

CX-007669: Categorical Exclusion Determination  

Broader source: Energy.gov [DOE]

Vegetative Response to Metal Exposure in a Growing Media CX(s) Applied: B3.6 Date: 11/07/2011 Location(s): South Carolina Offices(s): Savannah River Operations Office

384

CX-007717: Categorical Exclusion Determination  

Broader source: Energy.gov [DOE]

Arcadia Biosciences, Inc. - Vegetative Production of Oil in a C4 Crop CX(s) Applied: B3.6 Date: 11/21/2011 Location(s): California Offices(s): Advanced Research Projects Agency-Energy

385

The Water-Wise Vegetable Garden: An Analysis of the Potential for Irrigation through Rainwater Harvesting in Sunny Northern California  

E-Print Network [OSTI]

vegetables spinach and cabbage have a lower water demandmelons, spinach and yellow corn are among the most water-

Smith, Adrienne; Esterer-Vogel, Elisabeth

2009-01-01T23:59:59.000Z

386

The Water-Wise Vegetable Garden: An Analysis of the Potential for Irrigation through Rainwater Harvesting in Sunny Northern California  

E-Print Network [OSTI]

above the vegetable beds. Heavy water tanks require strongspaces. Since water is very heavy (8 pounds per gallon) it

Smith, Adrienne; Esterer-Vogel, Elisabeth

2009-01-01T23:59:59.000Z

387

Vegetative covers: Special study. [Uranium Mill Tailings Remedial Action (UMTRA) Project  

SciTech Connect (OSTI)

This report describes the findings of a special study on the use of vegetative covers to stabilize tailings piles for the Uranium Mill Tailings Remedial Action (UMTRA) Project. The principal rationale for using plants would be to establish a dynamic system for controlling water balance. Specifically, vegetation would be used to intercept and transpire precipitation to the atmosphere, rather than allowing water to drain into the tailings and mobilize contaminants. This would facilitate compliance with groundwater standards proposed for the UMTRA Project by the Environmental Protection Agency. The goals of the study were to (1) evaluate the feasibility of using vegetative covers on UMTRA Project piles, (2) define the advantages and disadvantages of vegetative covers, and (3) develop general guidelines for their use when such use seems reasonable. The principal method for the study was to analyze and apply to the UMTRA Project the results of research programs on vegetative covers at other US Department of Energy (DOE) waste management facilities. The study also relied upon observations made of existing stabilized piles at UMTRA Project sites (Shiprock, New Mexico; Burrell, Pennsylvania; and Clive, Utah) where natural vegetation is growing on the rock-covered surfaces. Water balance and erosion models were also used to quantify the long-term performance of vegetative covers planned for the topslopes of stabilized piles at Grand Junction and Durango, Colorado, two UMTRA Project sites where the decision was made during the course of this special study to use vegetative covers. Elements in the design and construction of the vegetative covers at these two sites are discussed in the report, with explanations of the differing features that reflect differing environmental conditions.

Not Available

1988-11-01T23:59:59.000Z

388

Bonneville Power Administration Transmission System Vegetation Management Program - Final Environmental Impact Statement  

SciTech Connect (OSTI)

Bonneville is responsible for maintaining a network of 24,000 kilometers (km) or 15,000 miles (mi.) of electric transmission lines and 350 substations in a region of diverse vegetation. This vegetation can interfere with electric power flow, pose safety problems for us and the public, and interfere with our ability to maintain these facilities. We need to (1) keep vegetation away from our electric facilities; (2) increase our program efficiency and consistency; (3) review herbicide use (under increased public scrutiny); and (4) maximize the range of tools we can use while minimizing environmental impact (Integrated Vegetation Management). This Final Environmental Impact Statement (FEIS) establishes Planning Steps for managing vegetation for specific projects (to be tiered to this Environmental Impact Statement (EIS)). In addition to No Action (current practice), alternatives are presented for Rights-of-way, Electric Yards, and Non-electric Facilities (landscaping, work yards). Four vegetation control methods are analyzed manual, mechanical, herbicide, and biological. Also evaluated are 23 herbicide active ingredients and 4 herbicide application techniques (spot, localized, broadcast, and aerial). For rights-of-way, we consider three sets of alternatives: alternative management approaches (time-driven or establishing low-growing plant communities); alternative method packages; and, if herbicides are in a methods package, alternative vegetation selections (noxious weeds, deciduous, or any vegetation). For electric yards, one herbicide-use alternative is considered. For non-electric facilities, two method package alternatives are considered. For rights-of-way, the environmentally preferred alternative(s) would use manual, mechanical, and biological control methods, as well as spot and localized herbicide applications for noxious and deciduous plant species; the BPA-preferred alternative(s) would add broadcast and aerial herbicide applications, and would use herbicides on any vegetation. Both would favor a management approach that fosters low-growing plant communities.

N /A

2000-06-23T23:59:59.000Z

389

Supply Response and Impact of Government-Supported Crops on the Texas Vegetable Industry  

E-Print Network [OSTI]

Supply functions, elasticity estimates, and nonjointness test results consistently indicated that few commodities compete economically in the production of six major Texas vegetables (cabbage, cantaloupes, carrots, onions, potatoes, and watermelons). Significant bias effects caused by government-supported commodities, fixed inputs, and technological change were observed and measured. Nonnested test results for the hypothesis of sequential decision making by vegetable producers were inconclusive, but they gave greater likelihood support to sequential than to contemporaneous decision making. Many crops are produced under provision of gov-ernment programs intended both to prevent severe drops in prices received by farmers and to limit supplies. Diversion payments, price supports, and acreage restrictions are examples of governmental policies designed to stabilize and control field crop production in the U.S, Vegetable production and marketing, on the other hand, are often subject only to minimum standards implemented by grow-ers ’ associations and shippers to ensure quality of the fresh produce. Their prices are allowed to vary according to market conditions prevailing at the time of harvest. Meanwhile, health-conscious con-sumers are enhancing their diets by expanding con-sumption of vegetables. For example, per capita consumption of fresh vegetables in the U.S. has increased more than a third in less than 15 years, rising from 75 to 102 pounds between 1975 and 1989 (USDA). Texas is a major vegetable producing state. In 1989 it ranked sixth among the 50 states in value of vegetables produced and fourth in value of fresh vegetables produced (USDA). Considerable re-sources are devoted to them, and income generated from vegetable production and associated agribus-iness activities contribute substantially to the eco-

Fermin Ornelas; C. Richard Shumway

390

Removal of Waterborne Particles by Electrofiltration: Pilot-Scale Testing  

E-Print Network [OSTI]

researchers conducted bench-scale experiments to verify the effectiveness of electrofiltration, few studies plant. Presedimentation basin water was used as the influent with a turbidity ranging from 12 to 37 NTU to be more effective for removal of smaller particles (

Li, Ying

391

Thief process for the removal of mercury from flue gas  

DOE Patents [OSTI]

A system and method for removing mercury from the flue gas of a coal-fired power plant is described. Mercury removal is by adsorption onto a thermally activated sorbent produced in-situ at the power plant. To obtain the thermally activated sorbent, a lance (thief) is inserted into a location within the combustion zone of the combustion chamber and extracts a mixture of semi-combusted coal and gas. The semi-combusted coal has adsorptive properties suitable for the removal of elemental and oxidized mercury. The mixture of semi-combusted coal and gas is separated into a stream of gas and semi-combusted coal that has been converted to a stream of thermally activated sorbent. The separated stream of gas is recycled to the combustion chamber. The thermally activated sorbent is injected into the duct work of the power plant at a location downstream from the exit port of the combustion chamber. Mercury within the flue gas contacts and adsorbs onto the thermally activated sorbent. The sorbent-mercury combination is removed from the plant by a particulate collection system.

Pennline, Henry W. (Bethel Park, PA); Granite, Evan J. (Wexford, PA); Freeman, Mark C. (South Park Township, PA); Hargis, Richard A. (Canonsburg, PA); O'Dowd, William J. (Charleroi, PA)

2003-02-18T23:59:59.000Z

392

Removal of Heavy Metals from Industrial Effluent Using Bacteria  

E-Print Network [OSTI]

Industrial development results in the generation of industrial effluents, and if untreated results in water, sediment and soil pollution. (Fakayode and Onianwa, 2002 ? Fakayode, 2005). Industrial wastes and emission contain toxic and hazardous substances, most of which are detrimental to human health (Jimena et al.,2008 ? Ogunfowokan et al.,2005 ? Rajaram et al.,2008). The key pollutants include heavy metals, chemical wastes and oil spills etc. Heavy metal resistant bacteria have significant role in bioremediation of heavy metals in wastewater. The objective of this work is to study the role of bacteria in removing the heavy metals present in the industrial effluent.Five effluent samples out of nine were selected for this study due to high content of heavy metals. The heavy metals Hg and Cu were removed by Bacillus sp. The average Hg reduction was 45 % and Cu reduction was recorded as 62%. The heavy metals Cd, As and Co were removed by Pseudomonas sp. The average Cd reduction was 56%, average As reduction was 34 % and average Co reduction was recorded as 53%. The heavy metals Cd and Cu were removed by Staphylococcus sp. The average Cd reduction was 44 % and average Cu reduction was recorded as 34 %.

Manisha N; Dinesh Sharma; Arun Kumar

393

Sea Turtle Observations at Explosive Removals of Energy Structures  

E-Print Network [OSTI]

Sea Turtle Observations at Explosive Removals of Energy Structures GREGG R. GITSCHLAG and BRYAN A. HERCZEG Introduction In July 1992 the total number of oil and gas production platformsI in the Gulfof. In that year 51 dead sea turtles were found on upper Texas beaches during mid-March to mid-April following

394

Pentek metal coating removal system: Baseline report; Greenbook (chapter)  

SciTech Connect (OSTI)

The Pentek coating removal technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The Pentek coating removal system consisted of the ROTO-PEEN Scaler, CORNER-CUTTER{reg_sign}, and VAC-PAC{reg_sign}. They are designed to remove coatings from steel, concrete, brick, and wood. The Scaler uses 3M Roto Peen tungsten carbide cutters while the CORNER-CUTTER{reg_sign} uses solid needles for descaling activities. These hand tools are used with the VAC-PAC{reg_sign} vacuum system to capture dust and debris as removal of the coating takes place. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. Dust exposure minimal, but noise exposure was significant. Further testing for each exposure is recommended because of the environment where the testing demonstration took place. It is feasible that the dust and noise levels will be higher in an enclosed operating environment of different construction. In addition, other areas of concern found were arm-hand vibration, whole-body, ergonomics, heat stress, tripping hazards, electrical hazards, machine guarding, and lockout/tagout.

NONE

1997-07-31T23:59:59.000Z

395

Justification to remove 333 Building fire suppression system  

SciTech Connect (OSTI)

Justification to remove the 333 Building fire suppression system is provided. The Maximum Possible Fire Loss (MPFL) is provided (approximately $800K), potential radiological and toxicological impacts from a postulated fire are discussed, Life Safety Code issues are addressed, and coordination with the Hanford Fire Department is assured.

Benecke, M.W.

1995-12-04T23:59:59.000Z

396

Investigating the Use of Biosorbents to Remove Arsenic from Water  

E-Print Network [OSTI]

, As (III), and arsenate, As (V), from water. Batch reactors were employed to assess the percent removal, reaction kinetics, adsorption capacity, and desorption of each arsenic species onto/from biosorbents under pH buffered and non?buffered conditions...

Erapalli, Shreyas

2011-02-22T23:59:59.000Z

397

Argonne Electrochemical Technology Program Sulfur removal from reformate  

E-Print Network [OSTI]

Argonne Electrochemical Technology Program Sulfur removal from reformate Xiaoping Wang, Theodore Krause, and Romesh Kumar Chemical Engineering Division Argonne National Laboratory Hydrogen, Fuel Cells, and Infrastructure Technologies 2003 Merit Review Berkeley, CA May 19-22, 2003 #12;Argonne Electrochemical Technology

398

Columbia River Channel Improvement Project Rock Removal Blasting: Monitoring Plan  

SciTech Connect (OSTI)

This document provides a monitoring plan to evaluate take as outlined in the National Marine Fisheries Service 2002 Biological Opinion for underwater blasting to remove rock from the navigation channel for the Columbia River Channel Improvement Project. The plan was prepared by the Pacific Northwest National Laboratory (PNNL) for the U.S. Army Corps of Engineers (USACE), Portland District.

Carlson, Thomas J.; Johnson, Gary E.

2010-01-29T23:59:59.000Z

399

Removing Redundancy and Inconsistency in Memory-Based Collaborative Filtering  

E-Print Network [OSTI]

Removing Redundancy and Inconsistency in Memory- Based Collaborative Filtering Kai Yu Siemens AG, Corporate Technology & University of Munich, Germany kai.yu.external@mchp.siemens. de Xiaowei Xu Information Science Department University of Arkansas at Little Rock xwxu@ualr.edu Anton Schwaighofer Siemens AG

Tresp, Volker

400

Method for removal of mercury from various gas streams  

DOE Patents [OSTI]

The invention provides for a method for removing elemental mercury from a fluid, the method comprising irradiating the mercury with light having a wavelength of approximately 254 nm. The method is implemented in situ at various fuel combustion locations such as power plants and municipal incinerators.

Granite, E.J.; Pennline, H.W.

2003-06-10T23:59:59.000Z

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Proceedings: Indoor Air 2005 OZONE REMOVAL BY RESIDENTIAL HVAC FILTERS  

E-Print Network [OSTI]

Proceedings: Indoor Air 2005 2366 OZONE REMOVAL BY RESIDENTIAL HVAC FILTERS P Zhao1,2 , JA Siegel1, Austin, Texas 78758, USA ABSTRACT HVAC filters have a significant influence on indoor air quality% for Filter #2 at a face velocity of 0.81 cm/s. The potential for HVAC filters to affect ozone concentrations

Siegel, Jeffrey

402

Particulate contamination removal from wafers using plasmas and mechanical agitation  

DOE Patents [OSTI]

Particulate contamination removal from wafers is disclosed using plasmas and mechanical agitation. The present invention includes the use of plasmas with mechanical agitation for removing particulate matter from the surface of a wafer. The apparatus hereof comprises a mechanical activator, at least one conducting contact pin for transferring the vibration from the activator to the wafer, clamp fingers that maintain the wafer`s position, and means for generating a plasma in the vicinity of the surface of the wafer, all parts of the cleaning apparatus except the mechanical activator and part of the contact pin being contained inside the processing chamber. By exposing a wafer to a plasma and providing motion thereto in a direction perpendicular to its surface, the bonding between the particulate matter and the surface may be overcome. Once free of the wafer surface, the particulates become charged by electrons from the plasma and are drawn into the plasma by attractive forces which keep them from redepositing. The introduction of a flowing gas through the plasma sweeps the particulates away from the wafer and out of the plasma. The entire surface is cleaned during one cleaning step. The use of an rf plasma to accomplish the particulate removal was found to remove more than 90% of the particulates. 4 figs.

Selwyn, G.S.

1998-12-15T23:59:59.000Z

403

Development of Silica/Vanadia/ Titania Catalysts for Removal of  

E-Print Network [OSTI]

mercury (Hg0) from simulated coal-combustion flue gas. Experiments were carried out in fixed-bed reactorsDevelopment of Silica/Vanadia/ Titania Catalysts for Removal of Elemental Mercury from Coal-Combustion the composition and microstructures of SCR (selective catalytic reduction) catalysts for Hg0 oxidation in coal-combustion

Li, Ying

404

Removal of Natural Steroid Hormones from Wastewater Using  

E-Print Network [OSTI]

Removal of Natural Steroid Hormones from Wastewater Using Membrane Contactor Processes J O S H U water resources and increased interest in wastewater reclamation for potable reuse. This interest has in the study of wastewater reuse in advanced life support systems (e.g., space missions) because

405

The Minimum Constraint Removal Problem with Three Robotics Applications  

E-Print Network [OSTI]

The Minimum Constraint Removal Problem with Three Robotics Applications Kris Hauser Abstract on three example applications: generating human-interpretable excuses for failure, motion planning under their failures. · In human-robot interaction, semantically meaningful explanations would help people diagnose

Indiana University

406

The Minimum Constraint Removal Problem with Three Robotics Applications  

E-Print Network [OSTI]

The Minimum Constraint Removal Problem with Three Robotics Applications Kris Hauser September 13 strategies. It is demonstrated on three example applications: gener- ating human-interpretable excuses, then they provide no explanation for the failure. For several applications, it would be useful for planners

Indiana University

407

Removing Systematic Errors from Rotating Shadowband Pyranometer Data Frank Vignola  

E-Print Network [OSTI]

Removing Systematic Errors from Rotating Shadowband Pyranometer Data Frank Vignola Solar Radiation irradiance be- cause they do not require manual adjustment of trackers. However, a RSP requires the use of solar cell based pyranometers which underestimate diffuse irradiance by 20- 30% under clear sky

Oregon, University of

408

Process for removing polymer-forming impurities from naphtha fraction  

DOE Patents [OSTI]

Polymer precursor materials are vaporized without polymerization or are removed from a raw naphtha fraction by passing the raw naphtha to a vaporization zone and vaporizing the naphtha in the presence of a wash oil while stripping with hot hydrogen to prevent polymer deposits in the equipment. 2 figs.

Kowalczyk, D.C.; Bricklemyer, B.A.; Svoboda, J.J.

1983-12-27T23:59:59.000Z

409

Mercury removal in utility wet scrubber using a chelating agent  

DOE Patents [OSTI]

A method for capturing and reducing the mercury content of an industrial flue gas such as that produced in the combustion of a fossil fuel or solid waste adds a chelating agent, such as ethylenediaminetetraacetic acid (EDTA) or other similar compounds like HEDTA, DTPA and/or NTA, to the flue gas being scrubbed in a wet scrubber used in the industrial process. The chelating agent prevents the reduction of oxidized mercury to elemental mercury, thereby increasing the mercury removal efficiency of the wet scrubber. Exemplary tests on inlet and outlet mercury concentration in an industrial flue gas were performed without and with EDTA addition. Without EDTA, mercury removal totaled 42%. With EDTA, mercury removal increased to 71%. The invention may be readily adapted to known wet scrubber systems and it specifically provides for the removal of unwanted mercury both by supplying S.sup.2- ions to convert Hg.sup.2+ ions into mercuric sulfide (HgS) and by supplying a chelating agent to sequester other ions, including but not limited to Fe.sup.2+ ions, which could otherwise induce the unwanted reduction of Hg.sup.2+ to the form, Hg.sup.0.

Amrhein, Gerald T. (Louisville, OH)

2001-01-01T23:59:59.000Z

410

-CONF-820664--9 DE82 018264 REMOVE  

E-Print Network [OSTI]

IFLE COPY - CONF-820664--9 DO NOT DE82 018264 REMOVE FIELD TESTING ENERGY-SAVING HERMETICGonmmnt o yiy rrtcy ttheof. #12;FIELD TESTING ENERGY SAVING HERMETIC COMPRESSORS IN RESIDENTIAL 49509 Abstract The design of an energy saving compressor for low back pressure applications is reviewed

Oak Ridge National Laboratory

411

Reactive Phosphorus Removal from Aquaculture and Poultry Productions  

E-Print Network [OSTI]

Reactive Phosphorus Removal from Aquaculture and Poultry Productions Systems Using Polymeric and poultry production wastewater effluents. The sorbent used was a cross-linked polyamine (PAA,HCl) polymeric poultry and aquaculture wastewater effluents. Upon treatment, phosphorus anion concentrations were reduced

Rubloff, Gary W.

412

Apparatus for removably holding a plurality of microballoons  

DOE Patents [OSTI]

The present invention relates generally to the manipulation of microballoons and more particularly to an apparatus for removably holding a plurality of microballoons in order to more efficiently carry out the filling of the microballoons with a known quantity of gas.

Jorgensen, B.S.

1984-06-05T23:59:59.000Z

413

Instructions for use Removal of Oxygen and Nitrogen from Niobium  

E-Print Network [OSTI]

Instructions for use #12;------ Removal of Oxygen and Nitrogen from Niobium by External Gettering of Energy Science and Technology, Kyoto University Yoshida-Honmachi, Sakyo-ku, Kyoto 606-01 Japan Keywords External Gettering, Purification of Niobium, Thermodynamics of Impurities, Oxygen Diffusion, Purity

Tachizawa, Kazuya

414

Method for removing particulate matter from a gas stream  

DOE Patents [OSTI]

Particulate matter is removed from a stream of pressurized gas by directing the stream of gas upwardly through a bed of porous material, the porous bed being held in an open ended container and at least partially submerged in liquid. The passage of the gas through the porous bed sets up a circulation in the liquid which cleans the particulate matter from the bed.

Postma, Arlin K. (Benton City, WA)

1984-01-01T23:59:59.000Z

415

Apparatuses and methods for removal of ink buildup  

SciTech Connect (OSTI)

A substrate patterning method including the steps of spraying ink on a surface of a substrate, the spraying of the ink resulting in an overspray of excess ink past an edge of the substrate; changing a temperature of the excess ink to cause a change in a viscosity of the excess ink; and removing the excess ink having the changed viscosity.

Cudzinovic, Michael; Pass, Thomas; Rogers, Rob; Sun, Ray-Hon; Sun, Sheng; Wahlstrom, Ben; Fuhrman, Dennis Jason; Altendorf, Kyle David

2013-03-12T23:59:59.000Z

416

MAILLER et al. Removal of priority and emerging substances by  

E-Print Network [OSTI]

of micropollutants in conventional wastewater treatment plants (WWTPs) composed by primary and biological treatmentsMAILLER et al. Removal of priority and emerging substances by biological and tertiary treatments in the case of urban areas (Heberer 2002). This implies a large understanding of wastewater treatment

Paris-Sud XI, Université de

417

An Adaptive Kalman Filter for Removing Baseline Wandering in ECG  

E-Print Network [OSTI]

An Adaptive Kalman Filter for Removing Baseline Wandering in ECG Signals MA Mneimneh, EE Yaz, MT misleads ECG anno- tators from accurate identification of the ECG features. Previous work that deals with baseline wandering re- moval requires the identification of the QRS complex or other ECG features prior

Povinelli, Richard J.

418

Nutrient Removal Mechanisms in a Cold Climate Gravel Wetland  

E-Print Network [OSTI]

Nutrient Removal Mechanisms in a Cold Climate Gravel Wetland Alison Watts, Robert Roseen, Kim Farah and development of stormwater treatment systems Gregg Hall 35 Colovos Road Durham, New Hampshire 03824-3534 603.862.4024 http://www.unhsc.unh.edu #12;POROUS ASPHALT Watershed Boundary #12;#12;Gravel Wetland Effluent sampling

419

Nutrient Removal Mechanisms in a Cold Climate Gravel Wetland  

E-Print Network [OSTI]

Nutrient Removal Mechanisms in a Cold Climate Gravel Wetland Alison Watts, Robert Roseen, Kim Farah and development of stormwater treatment systems Gregg Hall 35 Colovos Road Durham, New Hampshire 03824-3534 603;Gravel Wetland Sampling within the system #12;NEIWPCC-UNH Project Goals Validation of constructed gravel

420

Detroit Edison's Fermi 1 - Preparation for Reactor Removal  

SciTech Connect (OSTI)

This paper is intended to provide information about the ongoing decommissioning tasks at Detroit Edison's Fermi 1 plant, and in particular, the work being performed to prepare the reactor for removal and disposal. In 1972 Fermi 1 was shutdown and the fuel returned to the Atomic Energy Commission. By the end of 1975, a retirement plan was prepared, the bulk sodium removed, and the plant placed in a safe store condition. The plant systems were left isolated with the sodium containing systems inert with carbon dioxide in an attempt to form a carbonate layer, thus passivating the underlying reactive sodium. In 1996, Detroit Edison determined to evaluate the condition of the plant and to make recommendations in relation to the Fermi 1 future plans. At the end of 1997 approval was obtained to remove the bulk asbestos and residual alkali-metals (i.e., sodium and sodium potassium (NaK)). In 2000, full nuclear decommissioning of the plant was approved. To date, the bulk asbestos insulation has been removed, and the only NaK remaining is located in six capillary instrument tubes. The remaining sodium is contained within the reactor, two of the three primary loops, and miscellaneous removed pipes and equipment to be processed. The preferred method for removing or reacting sodium at Fermi 1 is by injecting superheated steam into a heated, nitrogen inert system. The byproducts of this reaction are caustic sodium hydroxide, hydrogen gas, and heat. The decision was made to separate the three primary loops from the reactor for better control prior to processing each loop and the reactor separately. The first loop has already been processed. The main focus is now to process the reactor to allow removal and disposal of the Class C waste prior to the anticipated June 2008 closure of the Barnwell radioactive waste disposal facility located in South Carolina. Lessons learnt are summarized and concern: the realistic schedule and adherence to the schedule, time estimates, personnel accountability, back up or fill in work, work packages, condensation control, radiological contamination control, and organization of the waste stream.

Swindle, Danny [Sargent and Lundy Engineers, LLC, 55 E. Monroe Street, Chicago, IL 60603 (United States)

2008-01-15T23:59:59.000Z

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Vegetation uptake from burial ground alpha waste trenches  

SciTech Connect (OSTI)

This study was conducted as part of an evaluation of the potential radiological consequences of reinhabiting the SRS burial ground. The objective was to determine the uptake of buried, low-level, transuranic waste from unlined earthen trenches by forest vegetation. Two tree plots were established in 1979. One plot was put over a trench containing alpha waste and the other in an area without trenches. When the tree seedlings were sampled during 1979 and 1980, and analysized for {sup 239}Pu and {sup 238}Pu, there was only a small difference in radionuclude concentration between trees planted over the trench and those planted on the control plot because of the limited root intrusion into the trench by the seedlings. However, when trees were sample in 1986, 1987, and 1988 and analyzed for {sup 241}Am, {sup 238}Pu, {sup 239}Pu, and {sup 237}Np activity, the average activity of all of these isotopes was significantly higher over the trenches than in the control plot. These measurements indicate that tree roots will extract transuranic isotopes from buried, low-level waste. The amount of radioisotopes moved from the trenches to the surface is small and the level in the trees is low enough that dose from exposure will be small. The long term effects of transport of radioisotopes from the trenches to the surface soil was evaluated by estimating the accumulation in the surface soil. Transuranic activity in selected food crops was calculated using the soil activity and the literature derived concentration factors. In all cases, the activity of the transuranic isotopes in the edible portion of the plants was quite low. The activity in the leaf tissue was much higher than in the seed. However, it should be noted that in only one case was the activity higher than the naturally occurring activity of {sup 40}K in the pine foliage.

Murphy, C.E. Jr.; Tuckfield, R.C.

1989-01-01T23:59:59.000Z

422

Carbon Ion Pump for Carbon Dioxide Removal - Energy Innovation Portal  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed New Substation Sites Proposed Route BTRICGEGR-N-CapturePortal Carbon

423

Lab sets new record for waste volume removed  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces and Interfaces Sample6, 2011 LOSEngineering |

424

Hedgehog(tm) Water Contaminant Removal System - Energy Innovation Portal  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation ProposedUsingFun with Bigfront.jpgcommunity200cellHeat Transfer in GEoperationPhysicalStartup

425

High capacity adsorption media for separating or removing constituents and  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation ProposedUsingFun withconfinement plasmas in thein the Assembly of PhotosystemVehiclesmethods

426

High capacity adsorption media for separating or removing constituents,  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation ProposedUsingFun withconfinement plasmas in thein the Assembly of

427

Fractionation and Removal of Solutes from Ionic Liquids - Energy Innovation  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation ProposedUsing ZirconiaPolicyFeasibilityFieldMinds" Give Forms (AllKurt'sKinneeffects

428

Functionalized Nanoporous Silica for Removal of Heavy Metals from  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation ProposedUsingFun with Big Sky Learning Fun with Big Sky Learning WHEN:AmplificationBiological

429

Energy Saving System to Remove Volatile Organic Compounds (VOCs) from  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation ProposedUsing Zirconia Nanoparticles asSecondCareerFebruary 2005Energy Saver 101:SavingP R I

430

METHODS OF USING ADSORPTION MEDIA FOR SEPARATING OR REMOVING CONSTITUENTS -  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces and InterfacesAdministration -Lowell L. Wood,3,March

431

Metal Organic Clathrates for Carbon Dioxide Removal - Energy Innovation  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces andMapping theEnergy StorageAdvanced Materials Advanced

432

Method for Removing Precipitates in Biofuel - Energy Innovation Portal  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces andMapping theEnergyInnovation Portal Biomass and Biofuels

433

Harmonic propagation of variability in surface energy balance within a coupled soil-vegetation-atmosphere system  

E-Print Network [OSTI]

[1] The response of a soil-vegetation-atmosphere continuum model to incoming radiation forcing is investigated in order to gain insights into the coupling of soil and atmospheric boundary layer (ABL) states and fluxes. The ...

Gentine, P.

434

E-Print Network 3.0 - african vegetation fires Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

2005 by the Ecological Society of America Summary: A MODEL-FRAMED EVALUATION OF ELEPHANT EFFECTS ON TREE AND FIRE DYNAMICS IN AFRICAN SAVANNAS PETER W. J... . The vegetation...

435

Assessing general relationships between aboveground biomass and vegetation structure parameters for improved carbon  

E-Print Network [OSTI]

Click Here for Full Article Assessing general relationships between aboveground biomass 2010; published 23 June 2010. [1] Lidarbased aboveground biomass is derived based on the empirical relationship between lidarmeasured vegetation height and aboveground biomass, often leading to large

Ni-Meister, Wenge

436

The effects of nutrition education on attitudes and behaviors of children regarding fruits and vegetables  

E-Print Network [OSTI]

curriculum has improved nutritional knowledge, attitudes, and behaviors regarding fruits and vegetables. One hundred and thirty - five students, representing ages five through twelve, approximately grades three through five, from four counties across...

Koch, Sharon Elaine, 1976-

2001-01-01T23:59:59.000Z

437

Feedbacks between flow, vegetation, deposition, and the implications for landscape development  

E-Print Network [OSTI]

Flow and sedimentation around patches of vegetation are important to landscape evolution, and a better understanding of these processes would facilitate more effective river restoration and wetlands engineering. In wetlands ...

Kondziolka, John M. (John Michael)

2014-01-01T23:59:59.000Z

438

Vegetation, soils, and surface hydrology of playa landforms in the Rio Grande Plains, Texas  

E-Print Network [OSTI]

Playas in the Rio Grande Plains of southern Texas were compared with respect to their: 1) size, shape, soil properties, and microtopography, 2) vegetation composition and structure, 3) surface water accumulation potential, and 4) disturbance history...

Farley, Andrea Lee

2012-06-07T23:59:59.000Z

439

E-Print Network 3.0 - arctic vegetation amplify Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Y N C H E T A L . 2001 American Meteorological Society Summary: vegetation, permafrost, soil, and the atmo- sphere to amplify ecosystem change. MacDonald et al. (1993... the...

440

Contribution of vegetation and peat fires to particulate air pollution in Southeast Asia  

E-Print Network [OSTI]

Smoke haze, caused by vegetation and peat fires in Southeast Asia, is of major concern because of its adverse impact on regional air quality. We apply two different methods (a chemical transport model and a Lagrangian ...

Reddington, C L

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Model and laboratory study of dispersion in flows with submerged vegetation  

E-Print Network [OSTI]

Vegetation is ubiquitous in rivers, estuaries, and wetlands, strongly influencing water conveyance and mass transport. The plant canopy affects mean and turbulent flow structure, and thus both advection and dispersion. ...

Murphy, E.

442

Coastal Marsh Vegetation Dynamics of the East Bay of Galveston Bay, Texas  

E-Print Network [OSTI]

The structure and function of coastal marshes results from a complex interaction of biotic and abiotic processes that continually influence the characteristics of marsh vegetation. A great deal of research has focused on how tidal processes...

Johnson, Jeremy Scott

2012-10-19T23:59:59.000Z

443

The coupled development of terrain and vegetation : the case of semiarid grasslands  

E-Print Network [OSTI]

The distribution of vegetation in semiarid landscapes organizes as a function of moisture availability, which is often mediated by the form of the land surface. Simultaneously the processes that shape the land surface are ...

Flores Cervantes, Javier Homero, 1977-

2010-01-01T23:59:59.000Z

444

Momentum and mass transport by coherent structures in a shallow vegetated shear flow  

E-Print Network [OSTI]

In many aquatic systems, from tidal creeks with fringing mangroves to rivers and associated floodplains, there exists an interface between dense vegetation and a high conveyance channel. A shear flow develops across this ...

White, Brian L., 1975-

2006-01-01T23:59:59.000Z

445

Investigation of the utility of the vegetation condition index (VCI) as an indicator of drought  

E-Print Network [OSTI]

The relationship between the satellite-based Vegetation Condition Index (VCI) and frequently used agricultural drought indices like Palmer Drought Severity Index, Palmer’s Z-index, Standard Precipitation Index, percent normal and deciles...

Ganesh, Srinivasan

2009-05-15T23:59:59.000Z

446

Relationships of exotic plant communities with native vegetation, environmental factors, disturbance, and landscape ecosystems  

E-Print Network [OSTI]

ecosystems in numerous ways. Theories on relation- ships of exotic species invasions with native vegetation strongly related to the eco- system classification. For example, mean exotic cover ranged from

Abella, Scott R.

447

Effects of dynamic vegetation and topography on hydrological processes in semi-arid areas  

E-Print Network [OSTI]

Ecosystems of dry climates represent a particularly interesting object for ecohydrological studies, as water is generally considered to be the key limiting resource. This work focuses on vegetation-water-energy dynamics ...

Ivanov, Valeri Yuryevich, 1974-

2006-01-01T23:59:59.000Z

448

The expansion of woody riparian vegetation, and subsequent stream restoration, influences the metabolism of prairie  

E-Print Network [OSTI]

The expansion of woody riparian vegetation, and subsequent stream restoration, influences, the restoration allowed recovery of some features of open-canopy prairie streams. Woody expansion apparently. Keywords: macroalgae, microalgae, primary production, restoration, streams Introduction North American

Dodds, Walter

449

A Comparison of Vegetation in Artificially Isolated Wetlands on West Galveston Island  

E-Print Network [OSTI]

The purpose of this study was to compare vegetation systems among three artificially isolated wetlands on the west end of Galveston Island. Sample sites were identified as isolated wetlands and anthropogenic impact was observed. Wetland plant...

Wilson, Ashley

2012-07-16T23:59:59.000Z

450

Using mobile technology to impact fruit and vegetable consumption in low-income youth  

E-Print Network [OSTI]

The benefits of fruits and vegetables (FV) include supplying nutrients and fiber to the diet, reducing risk of disease, and assisting in weight maintenance by increasing satiety and decreasing energy density of the diet. FV intake has been...

Hutcheson, Tresza Denae

2012-12-31T23:59:59.000Z

451

Recent Changes in Arctic Vegetation: Satellite Observations and Simulation Model Predictions  

E-Print Network [OSTI]

Chapter 2 Recent Changes in Arctic Vegetation: Satellite Observations and Simulation Model with a combination of satellite observations (Fig. 2.1) and field mea- surements, as projected by simulation modeling

Bhatt, Uma

452

CHARACTERIZATION OF MICROTOPOGRAPHY AND ITS INFLUENCE ON VEGETATION PATTERNS IN CREATED WETLANDS  

E-Print Network [OSTI]

CHARACTERIZATION OF MICROTOPOGRAPHY AND ITS INFLUENCE ON VEGETATION PATTERNS IN CREATED WETLANDS, Virginia, USA 20192 Abstract: Created wetlands are increasingly used to mitigate wetland loss. Thus, identifying wetland creation methods that enhance ecosystem development might increase the likelihood

453

Evaluation of vegetable oils for deep frying of batter-breaded meat nuggets  

E-Print Network [OSTI]

EVALUATION OF VEGETABLE OILS FOR DEEP FRYING OF BATIER-BREADED MEAT NUGGETS A Thesis by SHIRLEY ELIZABETH HOUSSON Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements for the degree... of MASTER OF SCIENCE August 1990 Major Subject: Food Science and Technology EVALUATION OF VEGETABLE OILS FOR DEEP FRYING OF BATTER-BREADED MEAT NUGGETS A Thesis by SHIRLEY ELIZABETH HOUSSON Approved as to style and content by: Ki Soon Rhee (Chair...

Housson, Shirley Elizabeth

1990-01-01T23:59:59.000Z

454

Canopy, litter and allelopathic effects of Ashe juniper (Juniperus ashei, Buchholz) on understory vegetation  

E-Print Network [OSTI]

CANOPY, ~ AND ALLELOPATHIC EFFECTS OF ASHE JUNIPER (JUNIPERUS ASHEI, BUCHHOLZ) ON UNDERSTORY VEGETATION A Thesis by LISA YVONNE YAGER Submitted to the Office of Graduate Studies of Texas A&M University in partial fufillment... of the requirements for the degree of MASTER OF SCIENCE December 1993 Major Subject: Range Science CANOPY, LIITER AND ALLELOPATHIC EFFECTS OF ASHE JUNIPER (JUNIPERUS ASHEI, BUCHHOLZ) ON UNDERSTORY VEGETATION A Thesis by LISA YVONNE YAGER Submitted to Texas A...

Yager, Lisa Yvonne

1993-01-01T23:59:59.000Z

455

Vegetative covers for sediment control and phosphorus sequestration from dairy waste application fields  

E-Print Network [OSTI]

VEGETATIVE COVERS FOR SEDIMENT CONTROL AND PHOSPHORUS SEQUESTRATION FROM DAIRY WASTE APPLICATION FIELDS A Thesis by SUBHASIS GIRI Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment... of the requirements for the degree of MASTER OF SCIENCE August 2008 Major Subject: Biological and Agricultural Engineering VEGETATIVE COVERS FOR SEDIMENT CONTROL AND PHOSPHORUS SEQUESTRATION FROM DAIRY WASTE APPLICATION FIELDS A Thesis...

Giri, Subhasis

2008-10-10T23:59:59.000Z

456

Long-wave infrared imaging of vegetation for detecting leaking CO2 gas  

E-Print Network [OSTI]

Long-wave infrared imaging of vegetation for detecting leaking CO2 gas Jennifer E. Johnson Joseph A for detecting leaking CO2 gas Jennifer E. Johnson,a Joseph A. Shaw,a Rick Lawrence,b Paul W. Nugent,a Laura M of these calibrated imagers is imaging of vegetation for CO2 gas leak detection. During a four-week period

Shaw, Joseph A.

457

Growth response of selected vegetable species to plant residue of guar (Cyamopsis tetragonoloba (L.) Taub.)  

E-Print Network [OSTI]

GROWTH RESPONSE OF SELECTED VEGETABLE SPECIES TO PLANT RESIDUE OF GUAR (Cyamopsis tetragonoloba (L. ) Taub. ) A Thesis by DEBBIE JOHN REID Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment... of the requirements for the degree of MASTER OF SCIENCE December 1992 Major Subject: Horticulture GROWTH RESPONSE OF SELECTED VEGETABLE SPECIES TO PLANT RESIDUE OF GUAR (Cyamopsis tetragonoloba (L. ) Taub. ) A Thesis by DEBBIE JOHN REID Approved as to style...

Reid, Debbie John

1992-01-01T23:59:59.000Z

458

An evaluation of low-density introductions of triploid grass carp in vegetated small sportfishing impoundments  

E-Print Network [OSTI]

AN EVALUATION OF LOW-DENSITY INTRODUCTIONS OF TRIPLOID GRASS CARP IN VEGETATED SMALL SPORTFISHING IMPOUNDMENTS A Thesis by BRIAN GENE BLACKWELL Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment... of the requirements for the degree of MASTER OF SCIENCE December 1993 Major Subject: Wildlife and Fisheries Sciences AN EVALUATION OF LOW-DENSITY INTRODUCTIONS OF TRIPLOID GRASS CARP IN VEGETATED SMALL SPORTFISHING IMPOUNDMENTS A Thesis by BRIAN GENE...

Blackwell, Brian Gene

2012-06-07T23:59:59.000Z

459

Use of vegetation to ameliorate building microclimates: an assessment of energy-conservation potentials  

SciTech Connect (OSTI)

The space-conditioning energy conservation potentials of landscapes designed to ameliorate building microclimates are evaluated. The physical bases for vegetative modifications of climate are discussed, and results of past study of the effects of vegetation on space-conditioning energy consumption in buildings are reviewed. The state-of-the-art of energy-conserving landscape designs is assessed and recommendations are presented for further research.

Hutchison, B.A.; Taylor, F.G.; Wendt, R.L.

1982-04-01T23:59:59.000Z

460

Satellite image analysis for surveillance, vegetation and climate change  

SciTech Connect (OSTI)

Recently, many studies have provided abundant evidence to show the trend of tree mortality is increasing in many regions, and the cause of tree mortality is associated with drought, insect outbreak, or fire. Unfortunately, there is no current capability available to monitor vegetation changes, and correlate and predict tree mortality with CO{sub 2} change, and climate change on the global scale. Different survey platforms (methods) have been used for forest management. Typical ground-based forest surveys measure tree stem diameter, species, and alive or dead. The measurements are low-tech and time consuming, but the sample sizes are large, running into millions of trees, covering large areas, and spanning many years. These field surveys provide powerful ground validation for other survey methods such as photo survey, helicopter GPS survey, and aerial overview survey. The satellite imagery has much larger coverage. It is easier to tile the different images together, and more important, the spatial resolution has been improved such that close to or even higher than aerial survey platforms. Today, the remote sensing satellite data have reached sub-meter spatial resolution for panchromatic channels (IKONOS 2: 1 m; Quickbird-2: 0.61 m; Worldview-2: 0.5 m) and meter spatial resolution for multi-spectral channels (IKONOS 2: 4 meter; Quickbird-2: 2.44 m; Worldview-2: 2 m). Therefore, high resolution satellite imagery can allow foresters to discern individual trees. This vital information should allow us to quantify physiological states of trees, e.g. healthy or dead, shape and size of tree crowns, as well as species and functional compositions of trees. This is a powerful data resource, however, due to the vast amount of the data collected daily, it is impossible for human analysts to review the imagery in detail to identify the vital biodiversity information. Thus, in this talk, we will discuss the opportunities and challenges to use high resolution satellite imagery and machine learning theory to monitor tree mortality at the level of individual trees.

Cai, D Michael [Los Alamos National Laboratory

2011-01-18T23:59:59.000Z

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Use of microalgae to remove pollutants from power plant discharges  

DOE Patents [OSTI]

A method and system for removing pollutants dissolved in the aqueous discharge of a plant, such as a power plant, from a body of water having known hydraulogy and physicochemical characteristics, the method comprising (a) modifying the hydraulic system of the body of water including use of physical barriers to define a zone in a portion of the body of water which zone includes the discharge point and where the water has a range of physicochemical characteristics; (b) selecting a large and preferably filamentous, planktonically growing strain of algae adapted to absorb the particular pollutants and genetically dominating algae at the physicochemical characteristics of the zone; (c) establishing a colony of the selected algal strain in the zone; (d) harvesting a portion of the colony; and (e) reinnoculating the zone near the discharge point with a fraction of the harvested portion. The fraction used for reinnoculation can be adjusted to balance the rate of pollutant removal to the rate of pollutant discharge.

Wilde, Edward W. (1833 Pisgah Rd., North Augusta, SC 29841); Benemann, John R. (2741 O'Harte, San Pablo, CA 94806); Weissman, Joseph C. (2086 N. Porpoise Pt. La., Vero Beach, FL 32963); Tillett, David M. (911-3 Coquina La., Vero Beach, FL 32963)

1991-01-01T23:59:59.000Z

462

Methods for removing contaminant matter from a porous material  

DOE Patents [OSTI]

Methods of removing contaminant matter from porous materials include applying a polymer material to a contaminated surface, irradiating the contaminated surface to cause redistribution of contaminant matter, and removing at least a portion of the polymer material from the surface. Systems for decontaminating a contaminated structure comprising porous material include a radiation device configured to emit electromagnetic radiation toward a surface of a structure, and at least one spray device configured to apply a capture material onto the surface of the structure. Polymer materials that can be used in such methods and systems include polyphosphazine-based polymer materials having polyphosphazine backbone segments and side chain groups that include selected functional groups. The selected functional groups may include iminos, oximes, carboxylates, sulfonates, .beta.-diketones, phosphine sulfides, phosphates, phosphites, phosphonates, phosphinates, phosphine oxides, monothio phosphinic acids, and dithio phosphinic acids.

Fox, Robert V. (Idaho Falls, ID) [Idaho Falls, ID; Avci, Recep (Bozeman, MT) [Bozeman, MT; Groenewold, Gary S. (Idaho Falls, ID) [Idaho Falls, ID

2010-11-16T23:59:59.000Z

463

Process for removing sulfate anions from waste water  

DOE Patents [OSTI]

A liquid emulsion membrane process for removing sulfate anions from waste water is disclosed. The liquid emulsion membrane process includes the steps of: (a) providing a liquid emulsion formed from an aqueous strip solution and an organic phase that contains an extractant capable of removing sulfate anions from waste water; (b) dispersing the liquid emulsion in globule form into a quantity of waste water containing sulfate anions to allow the organic phase in each globule of the emulsion to extract and absorb sulfate anions from the waste water and (c) separating the emulsion including its organic phase and absorbed sulfate anions from the waste water to provide waste water containing substantially no sulfate anions.

Nilsen, David N. (Lebanon, OR); Galvan, Gloria J. (Albany, OR); Hundley, Gary L. (Corvallis, OR); Wright, John B. (Albany, OR)

1997-01-01T23:59:59.000Z

464

Methods of using adsorption media for separating or removing constituents  

DOE Patents [OSTI]

Methods of using an adsorption medium to remove at least one constituent from a feed stream. The method comprises contacting an adsorption medium with a feed stream comprising at least one constituent and removing the at least one constituent from the feed stream. The adsorption medium comprises a polyacrylonitrile (PAN) matrix and at least one metal hydroxide homogenously dispersed therein. The adsorption medium may comprise from approximately 15 wt % to approximately 90 wt % of the PAN and from approximately 10 wt % to approximately 85 wt % of the at least one metal hydroxide. The at least one metal hydroxide may be selected from the group consisting of ferric hydroxide, zirconium hydroxide, lanthanum hydroxide, cerium hydroxide, titanium hydroxide, copper hydroxide, antimony hydroxide, and molybdenum hydroxide.

Tranter, Troy J. (Idaho Falls, ID); Herbst, R. Scott (Idaho Falls, ID); Mann, Nicholas R. (Blackfoot, ID); Todd, Terry A. (Aberdeen, ID)

2011-10-25T23:59:59.000Z

465

Removal of arsenic compounds from spent catecholated polymer  

DOE Patents [OSTI]

Described is a process for removing arsenic from petroliferous derived liquids by contacting said liquid at an elevated temperature with a divinylbenzene-crosslinked polystyrene having catechol ligands anchored thereon. Also, described is a process for regenerating spent catecholated polystyrene by removal of the arsenic bound to it from contacting petroliferous liquid as described above and involves: a. treating said spent catecholated polystyrene, at a temperature in the range of about 20.degree. to 100.degree. C. with an aqueous solution of at least one carbonate and/or bicarbonate of ammonium, alkali and alkaline earth metals, said solution having a pH between about 8 and 10 and, b. separating the solids and liquids from each other. Preferably the regeneration treatment is in two steps wherein step (a) is carried out with an aqueous alcoholic carbonate solution containing lower alkyl alcohol, and, steps (a) and (b) are repeated using a bicarbonate.

Fish, Richard H. (Berkeley, CA)

1985-01-01T23:59:59.000Z

466

Method for removing metal ions from solution with titanate sorbents  

DOE Patents [OSTI]

A method for removing metal ions from solution comprises the steps of providing titanate particles by spray-drying a solution or slurry comprising sorbent titanates having a particle size up to 20 micrometers, optionally in the presence of polymer free of cellulose functionality as binder, said sorbent being active towards heavy metals from Periodic Table (CAS version) Groups IA, IIA, IB, IIB, IIIB, and VIII, to provide monodisperse, substantially spherical particles in a yield of at least 70 percent of theoretical yield and having a particle size distribution in the range of 1 to 500 micrometers. The particles can be used free flowing in columns or beds, or entrapped in a nonwoven, fibrous web or matrix or a cast porous membrane, to selectively remove metal ions from aqueous or organic liquid.

Lundquist, Susan H. (White Bear Township, MN); White, Lloyd R. (Minneapolis, MN)

1999-01-01T23:59:59.000Z

467

Method for removing hydrocarbon contaminants from solid materials  

DOE Patents [OSTI]

A system for removing hydrocarbons from solid materials. Contaminated solids are combined with a solvent (preferably terpene based) to produce a mixture. The mixture is washed with water to generate a purified solid product (which is removed from the system) and a drainage product. The drainage product is separated into a first fraction (consisting mostly of contaminated solvent) and a second fraction (containing solids and water). The first fraction is separated into a third fraction (consisting mostly of contaminated solvent) and a fourth fraction (containing residual solids and water). The fourth fraction is combined with the second fraction to produce a sludge which is separated into a fifth fraction (containing water which is ultimately reused) and a sixth fraction (containing solids). The third fraction is then separated into a seventh fraction (consisting of recovered solvent which is ultimately reused) and an eighth fraction (containing hydrocarbon waste).

Bala, Gregory A. (Idaho Falls, ID); Thomas, Charles P. (Idaho Falls, ID)

1995-01-01T23:59:59.000Z

468

Apparatus for removing hydrocarbon contaminants from solid materials  

DOE Patents [OSTI]

A system for removing hydrocarbons from solid materials. Contaminated solids are combined with a solvent (preferably terpene based) to produce a mixture. The mixture is washed with water to generate a purified solid product (which is removed from the system) and a drainage product. The drainage product is separated into a first fraction (consisting mostly of contaminated solvent) and a second fraction (containing solids and water). The first fraction is separated into a third fraction (consisting mostly of contaminated solvent) and a fourth fraction (containing residual solids and water). The fourth fraction is combined with the second fraction to produce a sludge which is separated into a fifth fraction (containing water which is ultimately reused) and a sixth fraction (containing solids). The third fraction is then separated into a seventh fraction (consisting of recovered solvent which is ultimately reused) and an eighth fraction (containing hydrocarbon waste).

Bala, Gregory A. (Idaho Falls, ID); Thomas, Charles P. (Idaho Falls, ID)

1996-01-01T23:59:59.000Z

469

Removal of field and embedded metal by spin spray etching  

DOE Patents [OSTI]

A process of removing both the field metal, such as copper, and a metal, such as copper, embedded into a dielectric or substrate at substantially the same rate by dripping or spraying a suitable metal etchant onto a spinning wafer to etch the metal evenly on the entire surface of the wafer. By this process the field metal is etched away completely while etching of the metal inside patterned features in the dielectric at the same or a lesser rate. This process is dependent on the type of chemical etchant used, the concentration and the temperature of the solution, and also the rate of spin speed of the wafer during the etching. The process substantially reduces the metal removal time compared to mechanical polishing, for example, and can be carried out using significantly less expensive equipment. 6 figs.

Contolini, R.J.; Mayer, S.T.; Tarte, L.A.

1996-01-23T23:59:59.000Z

470

Negative kinetic energy term of general relativity and its removing  

E-Print Network [OSTI]

We first present a new Lagrangian of general relativity, which can be divided into kinetic energy term and potential energy term. Taking advantage of vierbein formalism, we reduce the kinetic energy term to a sum of five positive terms and one negative term. Some gauge conditions removing the negative kinetic energy term are discussed. Finally, we present a Lagrangian that only include positive kinetic energy terms. To remove the negative kinetic energy term leads to a new field equation of general relativity in which there are at least five equations of constraint and at most five dynamical equations, this characteristic is different from the normal Einstein field equation in which there are four equations of constraint and six dynamical equations.

T. Mei

2009-03-30T23:59:59.000Z

471

Method of removing nitrogen oxides from exhaust gas mixtures  

SciTech Connect (OSTI)

A method of removing nitrogen oxides (NOX) from exhaust gas mixtures is described. The removal of NOX from exhaust gas mixtures is accomplished by exposing the exhaust gas mixture, in a manner that does not substantially impede the gas flow, to a ceramic material containing from about 75% to about 95% by weight silicon carbide and from about 0.3% to about 10.0% silica. A reduction of at least 85% of NOX from the mixture is to be expected and reductions up to 95 to 100% are attainable. Ceramic mixtures containing silicon nitride in amounts between about 10% and about 30% are found to reduce the amount of NOX in exhaust gases at temperatures as low as 200* C.

Batha, H.D.; Mason, J.H.; Thompson, S.R.

1980-03-04T23:59:59.000Z

472

Apparatus for removing hydrocarbon contaminants from solid materials  

DOE Patents [OSTI]

A system is described for removing hydrocarbons from solid materials. Contaminated solids are combined with a solvent (preferably terpene based) to produce a mixture. The mixture is washed with water to generate a purified solid product (which is removed from the system) and a drainage product. The drainage product is separated into a first fraction (consisting mostly of contaminated solvent) and a second fraction (containing solids and water). The first fraction is separated into a third fraction (consisting mostly of contaminated solvent) and a fourth fraction (containing residual solids and water). The fourth fraction is combined with the second fraction to produce a sludge which is separated into a fifth fraction (containing water which is ultimately reused) and a sixth fraction (containing solids). The third fraction is then separated into a seventh fraction (consisting of recovered solvent which is ultimately reused) and an eighth fraction (containing hydrocarbon waste). 4 figs.

Bala, G.A.; Thomas, C.P.

1996-02-13T23:59:59.000Z

473

Method for removing hydrocarbon contaminants from solid materials  

DOE Patents [OSTI]

A system is described for removing hydrocarbons from solid materials. Contaminated solids are combined with a solvent (preferably terpene based) to produce a mixture. The mixture is washed with water to generate a purified solid product (which is removed from the system) and a drainage product. The drainage product is separated into a first fraction (consisting mostly of contaminated solvent) and a second fraction (containing solids and water). The first fraction is separated into a third fraction (consisting mostly of contaminated solvent) and a fourth fraction (containing residual solids and water). The fourth fraction is combined with the second fraction to produce a sludge which is separated into a fifth fraction (containing water which is ultimately reused) and a sixth fraction (containing solids). The third fraction is then separated into a seventh fraction (consisting of recovered solvent which is ultimately reused) and an eighth fraction (containing hydrocarbon waste). 4 figs.

Bala, G.A.; Thomas, C.P.

1995-10-03T23:59:59.000Z

474

System for the removal of contaminant soil-gas vapors  

DOE Patents [OSTI]

A system extracts contaminated vapors from soil or other subsurface regions by using changes in barometric pressure to operate sensitive check valves that control air entry and removal from wells in the ground. The system creates an efficient subterranean flow of air through a contaminated soil plume and causes final extraction of the contaminants from the soil to ambient air above ground without any external energy sources.

Weidner, Jerry R. (Iona, ID); Downs, Wayne C. (Sugar City, ID); Kaser, Timothy G. (Ammon, ID); Hall, H. James (Idaho Falls, ID)

1997-01-01T23:59:59.000Z

475

System for the removal of contaminant soil-gas vapors  

DOE Patents [OSTI]

A system extracts contaminated vapors from soil or other subsurface regions by using changes in barometric pressure to operate sensitive check valves that control air entry and removal from wells in the ground. The system creates an efficient subterranean flow of air through a contaminated soil plume and causes final extraction of the contaminants from the soil to ambient air above ground without any external energy sources. 4 figs.

Weidner, J.R.; Downs, W.C.; Kaser, T.G.; Hall, H.J.

1997-12-16T23:59:59.000Z

476

Inflatable containment diaphragm for sealing and removing stacks  

DOE Patents [OSTI]

A diaphragm with an inflatable torus-shaped perimeter is used to seal at least one end of a stack so that debris that might be hazardous will not be released during removal of the stack. A diaphragm is inserted and inflated in the lower portion of a stack just above where the stack is to be cut such that the perimeter of the diaphragm expands and forms a seal against the interior surface of the stack.

Meskanick, G.R.; Rosso, D.T.

1993-04-13T23:59:59.000Z

477

Removable, hermetically-sealing, filter attachment system for hostile environments  

DOE Patents [OSTI]

A removable and reusable filter attachment system. A filter medium is fixed o, and surrounded by, a filter frame having a coaxial, longitudinally extending, annular rim. The rim engages an annular groove which surrounds the opening of a filter housing. The annular groove contains a fusible material and a heating mechanism for melting the fusible material. Upon resolidifying, the fusible material forms a hermetic bond with the rim and groove. Remelting allows detachment and replacement of the filter frame.

Mayfield, Glenn L [Richland, WA

1983-01-01T23:59:59.000Z

478

Nitrogen removal from natural gas using two types of membranes  

DOE Patents [OSTI]

A process for treating natural gas or other methane-rich gas to remove excess nitrogen. The invention relies on two-stage membrane separation, using methane-selective membranes for the first stage and nitrogen-selective membranes for the second stage. The process enables the nitrogen content of the gas to be substantially reduced, without requiring the membranes to be operated at very low temperatures.

Baker, Richard W.; Lokhandwala, Kaaeid A.; Wijmans, Johannes G.; Da Costa, Andre R.

2003-10-07T23:59:59.000Z

479

Efficiency of alum coagulation for removal of trihalomethane precursors  

E-Print Network [OSTI]

EFFICIENCY OF ALUM COAGULATION FOR REMOUAL OF TRIHALOMETHANE PRECURSORS A Thesis by JOE DAN SHANNON Submitted to the Graduate College of Texas ASM University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCE... August 1980 Major Subject: Civil Engineering EFFICIENCY OF ALUM COAGULATION FOR REMOVAL OF TRIHALOMETHANE PRECURSORS A Thesis by JOE DAN SHANNON Approved as to style and content by: (Chairman of Committee) (Member) (Memb ) (Head of Department...

Shannon, Joe Dan

1980-01-01T23:59:59.000Z

480

Fairer Trade, Removing Gender Bias in US Import Taxes  

E-Print Network [OSTI]

Fairer Trade Removing Gender Bias in US Import Taxes LORI L. TAYLOR AND JAWAD DAR Mosbacher Institute VOLUME 6 | ISSUE 3 | 2015 There are many inequalities in US tariff policy. Products imported from certain countries enter duty free..., the US Su- preme Court refused to hear appeals from import- ers Rack Room Shoes Inc. and Forever 21 Inc., thereby blocking their attempts to challenge an earlier ruling by the Court of Internation- al Trade. The importers had argued before the Court...

Taylor, Lori L.; Dar, Jawad

Note: This page contains sample records for the topic "vegetation removal cxs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Removal of testa from food grade copra by air classification  

E-Print Network [OSTI]

preparation of rv food grade copra. Carver and screw prepressing were used to remove some of the oil from the copra. The prepressed cakes were flaked and extracted wi. th hexane by two different methods of extraction, small batch extraction and filtration... column extrac- tion. The meal after air desolventization was dried and milled in an Alpine Kolloplex Impact Study Mill 160Z. The testa particles were separated from the coconut flour by means of air classifica- tion and sieving. To optimize...

Lopitakwong, Rommanee

1975-01-01T23:59:59.000Z

482

Building Removal Ongoing at DOE's Paducah Site | Department of Energy  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy UsageAUDITVehiclesTankless orA BRIEFAprilBudget FormulationCamberlyBuilding Removal

483

High Metal Removal Rate Process for Machining Difficult Materials  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeatMulti-Dimensional Subject:Ground Hawaii CleanHeatinHighMetal Removal

484

Removal of fluoride from aqueous solution by using alum sludge  

SciTech Connect (OSTI)

The ability of treated alum sludge to remove fluoride from aqueous solution has been investigated. The studies were carried out as functions of contact time, concentration of adsorbent and adsorbate, temperature, pH, and effect of concentrations of other anions. The data indicate that treated alum sludge surface sites are heterogeneous in nature and that fits into a heterogeneous site binding model. The optimum pH for complete removal of fluoride from aqueous solution was found to be 6. The rate of adsorption was rapid during the initial 5 minutes, and equilibrium was attained within 240 minutes. The adsorption followed first-order rate kinetics. The present system followed the Langmuir adsorption isotherm model. The loading factor (i.e., the milligram of fluoride adsorbed per gram of alum sludge) increased with initial fluoride concentration, whereas a negative trend was observed with increasing temperature. The influence of addition of anions on fluoride removal depends on the relative affinity of the anions for the surface and the relative concentrations of the anions.

Sujana, M.G.; Thakur, R.S.; Rao, S.B. [CSIR, Bhubaneswar (India). Regional Research Lab.] [CSIR, Bhubaneswar (India). Regional Research Lab.

1998-10-01T23:59:59.000Z

485

BOA: Pipe-asbestos insulation removal robot system  

SciTech Connect (OSTI)

This paper describes the BOA system, a mobile pipe-external crawler used to remotely strip and bag (possibly contaminated) asbestos-containing lagging and insulation materials (ACLIM) from various diameter pipes in (primarily) industrial installations across the DOE weapons complex. The mechanical removal of ACLIM is very cost-effective due to the relatively low productivity and high cost involved in human removal scenarios. BOA, a mechanical system capable of removing most forms of lagging (paper, plaster, aluminum sheet, clamps, screws and chicken-wire), and insulation (paper, tar, asbestos fiber, mag-block) uses a circular cutter and compression paddles to cut and strip the insulation off the pipe through compression, while a HEPA-filter and encapsulant system maintain a certifiable vacuum and moisture content inside the system and on the pipe, respectively. The crawler system has been built and is currently undergoing testing. Key design parameters and performance parameters are developed and used in performance testing. Since the current system is a testbed, we also discuss future enhancements and outline two deployment scenarios (robotic and manual) for the final system to be designed and completed by the end of FY `95. An on-site demonstration is currently planned for Fernald in Ohio and Oak Ridge in Tennessee.

Schempf, H.; Bares, J.; Mutschler, E. [and others

1995-12-31T23:59:59.000Z

486

Process for off-gas particulate removal and apparatus therefor  

DOE Patents [OSTI]

In the event of a breach in the off-gas line of a melter operation requiring closure of the line, a secondary vessel vent line is provided with a particulate collector utilizing atomization for removal of large particulates from the off-gas. The collector receives the gas containing particulates and directs a portion of the gas through outer and inner annular channels. The collector further receives a fluid, such as water, which is directed through the outer channel together with a second portion of the particulate-laden gas. The outer and inner channels have respective ring-like termination apertures concentrically disposed adjacent one another on the outer edge of the downstream side of the particulate collector. Each of the outer and inner channels curves outwardly away from the collector`s centerline in proceeding toward the downstream side of the collector. Gas flow in the outer channel maintains the fluid on the channel`s wall in the form of a ``wavy film,`` while the gas stream from the inner channel shears the fluid film as it exits the outer channel in reducing the fluid to small droplets. Droplets formed by the collector capture particulates in the gas stream by one of three mechanisms: impaction, interception or Brownian diffusion in removing the particulates. The particulate-laden droplets are removed from the fluid stream by a vessel vent condenser or mist eliminator. 4 figs.

Carl, D.E.

1997-10-21T23:59:59.000Z

487

Process for off-gas particulate removal and apparatus therefor  

DOE Patents [OSTI]

In the event of a breach in the off-gas line of a melter operation requiring closure of the line, a secondary vessel vent line is provided with a particulate collector utilizing atomization for removal of large particulates from the off-gas. The collector receives the gas containing particulates and directs a portion of the gas through outer and inner annular channels. The collector further receives a fluid, such as water, which is directed through the outer channel together with a second portion of the particulate-laden gas. The outer and inner channels have respective ring-like termination apertures concentrically disposed adjacent one another on the outer edge of the downstream side of the particulate collector. Each of the outer and inner channels curves outwardly away from the collector's centerline in proceeding toward the downstream side of the collector. Gasflow in the outer channel maintains the fluid on the channel's wall in the form of a "wavy film," while the gas stream from the inner channel shears the fluid film as it exits the outer channel in reducing the fluid to small droplets. Droplets formed by the collector capture particulates in the gas stream by one of three mechanisms: impaction, interception or Brownian diffusion in removing the particulates. The particulate-laden droplets are removed from the fluid stream by a vessel vent condenser or mist eliminator.

Carl, Daniel E. (Orchard Park, NY)

1997-01-01T23:59:59.000Z

488

LNAPL Removal from Unsaturated Porous Media using Surfactant Infiltration  

SciTech Connect (OSTI)

A series of unsaturated column experiments was performed to evaluate light non-aqueous phase liquid (LNAPL) fate and removal during surfactant solution infiltration. Surfactant-LNAPL phase behavior tests were conducted to optimize the remedial solutions. Packed sand and site sediment columns were first processed to establish representative LNAPL smear zone under unsaturated conditions. Infiltration of low-concentration surfactant was then applied in a stepwise flush mode, with 0.3 column pore volume (PV) of solution in each flush. The influence of infiltrated surfactant solution volume and pH on LNAPL removal was assessed. A LNAPL bank was observed at the very front of the first surfactant infiltration in each column, indicating that a very low surfactant concentration is needed to reduce the LNAPL-water interfacial tension sufficiently enough to mobilize trapped LNAPL under unsaturated conditions. More LNAPL was recovered as additional steps of surfactant infiltration were applied. Up to 99% LNAPL was removed after six infiltration steps, with less than 2.0 PV of total surfactant solution application, suggesting surfactant infiltration may be an effective method for vadose zone LNAPL remediation. The influence of pH tested in this study (3.99~10.85) was insignificant because the buffering capacity of the sediment kept the pH in the column higher than the zero point charge, pHzpc, of the sediment and therefore the difference between surfactant sorption was negligible.

Zhong, Lirong; Oostrom, Martinus

2012-11-19T23:59:59.000Z

489

Cesium removal using crystalline silicotitanate. Innovative technology summary report  

SciTech Connect (OSTI)

Approximately 100 million gallons of radioactive waste is stored in underground storage tanks at the Hanford Site, Idaho National Engineering and Environmental Laboratory (INEEL), Oak Ridge Reservation, and Savannah River Site (SRS). Most of the radioactivity comes from {sup 137}Cs, which emits high-activity gamma radiation. The Cesium Removal System is a modular, transportable, ion-exchange system configured as a compact processing unit. Liquid tank waste flows through columns packed with solid material, called a sorbent, that selectively adsorbs cesium and allows the other materials to pass through. The sorbent is crystalline silicotitanate (CST), an engineered material with a high capacity for sorbing cesium from alkaline wastes. The Cesium Removal System was demonstrated at Oak Ridge using Melton Valley Storage Tank (MVST) waste for feed. Demonstration operations began in September 1996 and were completed during June 1997. Prior to the demonstration, a number of ion-exchange materials were evaluated at Oak Ridge with MVST waste. Also, three ion-exchange materials and three waste types were tested at Hanford. These bench-scale tests were conducted in a hot cell. Hanford's results showed that 300 times less sorbent was used by selecting Ionsiv IE-911 over organic ion-exchange resins for cesium removal. This paper gives a description of the technology and discusses its performance, applications, cost, regulatory and policy issues and lessons learned.

NONE

1999-05-01T23:59:59.000Z

490

Ammonia removal process upgrade to the Acme Steel Coke Plant  

SciTech Connect (OSTI)

The need to upgrade the ammonia removal process at the Acme Steel Coke Plant developed with the installation of the benzene NESHAP (National Emission Standard for Hazardous Air Pollutants) equipment, specifically the replacement of the final cooler. At Acme Steel it was decided to replace the existing open cooling tower type final cooler with a closed loop direct spray tar/water final cooler. This new cooler has greatly reduced the emissions of benzene, ammonia, hydrogen sulfide and hydrogen cyanide to the atmosphere, bringing them into environmental compliance. At the time of its installation it was not fully recognized as to the effect this would have on the coke oven gas composition. In the late seventies the decision had been made at Acme Steel to stop the production of ammonia sulfate salt crystals. The direction chosen was to make a liquid ammonia sulfate solution. This product was used as a pickle liquor at first and then as a liquid fertilizer as more markets were developed. In the fall of 1986 the ammonia still was brought on line. The vapors generated from the operation of the stripping still are directed to the inlet of the ammonia absorber. At that point in time it was decided that an improvement to the cyclical ammonia removal process was needed. The improvements made were minimal yet allowed the circulation of solution through the ammonia absorber on a continuous basis. The paper describes the original batch process and the modifications made which allowed continuous removal.

Harris, J.L. [Acme Steel Co., Chicago, IL (United States). Chicago Coke Plant

1995-12-01T23:59:59.000Z

491

Pentek metal coating removal system: Baseline report; Summary  

SciTech Connect (OSTI)

The Pentek metal coating removal system consists of the ROTO-PEEN Scaler, CORNER-CUTTER(R), and VAC-PAC(R). The system is designed to remove coatings from steel, concrete, brick, and wood. The Scaler uses 3M ROTO-PEEN tungsten carbide cutters, while the CORNER-CUTTER(R) uses solid needles for descaling activities. These are used with the VAC-PAC(R) vacuum system to capture dust and debris as removal of the coating takes place. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. Dust exposure was minimal, but noise exposure was significant. Further testing for each exposure is recommended, since the outdoor environment where the testing demonstration took place may skew the results. It is feasible that dust and noise levels will be higher in an enclosed operating environment. Other areas of concern found were arm-hand vibration, whole-body vibration, ergonomics, heat stress, tripping hazards, electrical hazards, machine guarding, and lockout/tagout.

NONE

1997-07-31T23:59:59.000Z

492

Preliminary Evaluation of Removing Used Nuclear Fuel from Shutdown Sites  

SciTech Connect (OSTI)

This report fulfills the M2 milestone M2FT-13PN0912022, “Stranded Sites De-Inventorying Report.” In January 2013, the U.S. Department of Energy (DOE) issued the Strategy for the Management and Disposal of Used Nuclear Fuel and High-Level Radioactive Waste (DOE 2013). Among the elements contained in this strategy is an initial focus on accepting used nuclear fuel from shutdown reactor sites. This focus is consistent with the recommendations of the Blue Ribbon Commission on America’s Nuclear Future, which identified removal of stranded used nuclear fuel at shutdown sites as a priority so that these sites may be completely decommissioned and put to other beneficial uses (BRC 2012). Shutdown sites are defined as those commercial nuclear power reactor sites where the nuclear power reactors have been shut down and the site has been decommissioned or is undergoing decommissioning. In this report, a preliminary evaluation of removing used nuclear fuel from 12 shutdown sites was conducted. The shutdown sites were Maine Yankee, Yankee Rowe, Connecticut Yankee, Humboldt Bay, Big Rock Point, Rancho Seco, Trojan, La Crosse, Zion, Crystal River, Kewaunee, and San Onofre. These sites have no other operating nuclear power reactors at their sites and have also notified the U.S. Nuclear Regulatory Commission that their reactors have permanently ceased power operations and that nuclear fuel has been permanently removed from their reactor vessels. Shutdown reactors at sites having other operating reactors are not included in this evaluation.

Maheras, Steven J. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Best, Ralph E.; Ross, Steven B. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Buxton, Kenneth A. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); England, Jeffery L. [Savannah River National Laboratory, Aiken, SC (United States); McConnell, Paul E. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

2013-09-30T23:59:59.000Z

493

MULTIPLE POLLUTANT REMOVAL USING THE CONDENSING HEAT EXCHANGER  

SciTech Connect (OSTI)

The Integrated Flue Gas Treatment (IFGT) system is a new concept whereby a Teflon ® covered condensing heat exchanger is adapted to remove certain flue gas constituents, both particulate and gaseous, while recovering low level heat. The pollutant removal performance and durability of this device is the subject of a USDOE sponsored program to develop this technology. The program was conducted under contract to the United States Department of Energy?s Fossil Energy Technology Center (DOE-FETC) and was supported by the Ohio Coal Development Office (OCDO) within the Ohio Department of Development, the Electric Power Research Institute?s Environmental Control Technology Center (EPRI-ECTC) and Babcock and Wilcox - a McDermott Company (B&W). This report covers the results of the first phase of this program. This Phase I project has been a two year effort. Phase I includes two experimental tasks. One task dealt principally with the pollutant removal capabilities of the IFGT at a scale of about 1.2MWt. The other task studied the durability of the Teflon ® covering to withstand the rigors of abrasive wear by fly ash emitted as a result of coal combustion. The pollutant removal characteristics of the IFGT system were measured over a wide range of operating conditions. The coals tested included high, medium and low-sulfur coals. The flue gas pollutants studied included ammonia, hydrogen chloride, hydrogen fluoride, particulate, sulfur dioxide, gas phase and particle phase mercury and gas phase and particle phase trace elements. The particulate removal efficiency and size distribution was investigated. These test results demonstrated that the IFGT system is an effective device for both acid gas absorption and fine particulate collection. Although soda ash was shown to be the most effective reagent for acid gas absorption, comparative cost analyses suggested that magnesium enhanced lime was the most promising avenue for future study. The durability of the Teflon ® covered heat exchanger tubes was studied on a pilot-scale single- stage condensing heat exchanger (CHX ® ). This device was operated under typical coal-fired flue gas conditions on a continuous basis for a period of approximately 10 months. Data from the test indicate that virtually no decrease in Teflon ® thickness was observed for the coating on the first two rows of heat exchanger tubes, even at high inlet particulate loadings. Evidence of wear was present only at the microscopic level, and even then was very minor in severity.

B.J. JANKURA; G.A. KUDLAC; R.T. BAILEY

1998-06-01T23:59:59.000Z

494

Proton Delivery and Removal in [Ni(PR2NR?2)2]2+ Hydrogen...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Delivery and Removal in Ni(PR2NR?2)22+ Hydrogen Production and Oxidation Catalysts. Proton Delivery and Removal in Ni(PR2NR?2)22+ Hydrogen Production and Oxidation...

495

Removal of pertechnetate from simulated nuclear waste streams using supported zerovalent iron  

E-Print Network [OSTI]

be to use a technetium ion- exchange or sorbent materialtechnetium problem is to remove pertechnetate from the waste using commercially available polymeric ion exchangetechnetium-containing eluate that would be generated in removing pertechnetate from the commercial ion-exchange

Darab, John

2008-01-01T23:59:59.000Z

496

324 Building spent fuel segments pieces and fragments removal summary report  

SciTech Connect (OSTI)

As part of the 324 Building Deactivation Project, all Spent Nuclear Fuel (SNF) and Special Nuclear Material were removed. The removal entailed packaging the material into a GNS-12 cask and shipping it to the Central Waste Complex (CWC).

SMITH, C L

2003-01-09T23:59:59.000Z

497

Notice of Asbestos-Containing Material (ACM) Removal Request for Correction of Online ACM Inventory  

E-Print Network [OSTI]

Inventory This form is to be completed for all asbestos abatement/removal work at the University of Maryland and type of material removed -as listed on DES inventory. (Indicate "NPL" ­ if described material is "not

Rubloff, Gary W.

498

1,153-ton Waste Vault Removed from 300 Area - Vault held waste...  

Energy Savers [EERE]

1,153-ton Waste Vault Removed from 300 Area - Vault held waste tanks with contamination from Hanford's former laboratory facilities 1,153-ton Waste Vault Removed from 300 Area -...

499

SULFURIC ACID REMOVAL PROCESS EVALUATION: LONG-TERM RESULTS  

SciTech Connect (OSTI)

The objective of this project is to demonstrate the use of alkaline reagents injected into the furnace of coal-fired boilers as a means of controlling sulfuric acid emissions. The project is being co-funded by the U.S. DOE National Energy Technology Laboratory, under Cooperative Agreement DE-FC26-99FT40718, along with EPRI, the American Electric Power Company (AEP), FirstEnergy Corp., the Tennessee Valley Authority, and Dravo Lime, Inc. Sulfuric acid controls are becoming of increasing interest to power generators with coal-fired units for a number of reasons. Sulfuric acid is a Toxic Release Inventory species and can cause a variety of plant operation problems such as air heater plugging and fouling, back-end corrosion, and plume opacity. These issues will likely be exacerbated with the retrofit of selective catalytic reduction (SCR) for NO{sub x} control on many coal-fired plants, as SCR catalysts are known to further oxidize a portion of the flue gas SO{sub 2} to SO{sub 3}. The project previously tested the effectiveness of furnace injection of four different calcium-and/or magnesium-based alkaline sorbents on full-scale utility boilers. These reagents were tested during four one- to two-week tests conducted on two FirstEnergy Bruce Mansfield Plant (BMP) units. One of the sorbents tested was a magnesium hydroxide byproduct slurry produced from a modified Thiosorbic{reg_sign} Lime wet flue gas desulfurization system. The other three sorbents are available commercially and include dolomite, pressure-hydrated dolomitic lime, and commercial magnesium hydroxide. The dolomite reagent was injected as a dry powder through out-of-service burners, while the other three reagents were injected as slurries through air-atomizing nozzles inserted through the front wall of the upper furnace, either across from the nose of the furnace or across from the pendant superheater tubes. After completing the four one- to two-week tests, the most promising sorbents were selected for longer-term (approximately 25-day) full-scale tests on two different units. The longer-term tests were conducted to confirm the effectiveness of the sorbents tested over extended operation on two different boilers, and to determine balance-of-plant impacts. The first long-term test was conducted on FirstEnergy's BMP, Unit 3, and the second test was conducted on AEP's Gavin Plant, Unit 1. The Gavin Plant testing provided an opportunity to evaluate the effects of sorbent injected into the furnace on SO{sub 3} formed across an operating SCR reactor. This report presents the results from those long-term tests. The tests determined the effectiveness of injecting commercially available magnesium hydroxide slurry (Gavin Plant) and byproduct magnesium hydroxide slurry (both Gavin Plant and BMP) for sulfuric acid control. The results show that injecting either slurry could achieve up to 70 to 75% overall sulfuric acid removal. At BMP, this overall removal was limited by the need to maintain acceptable electrostatic precipitator (ESP) particulate control performance. At Gavin Plant, the overall sulfuric acid removal was limited because the furnace injected sorbent was less effective at removing SO{sub 3} formed across the SCR system installed on the unit for NOX control than at removing SO{sub 3} formed in the furnace. The long-term tests also determined balance-of-plant impacts from slurry injection during the two tests. These include impacts on boiler back-end temperatures and pressure drops, SCR catalyst properties, ESP performance, removal of other flue gas species, and flue gas opacity. For the most part the balance-of-plant impacts were neutral to positive, although adverse effects on ESP performance became an issue during the BMP test.

Gary M. Blythe; Richard McMillan

2002-07-03T23:59:59.000Z

500

Using Unmanned Helicopters to Assess Vegetation Cover in Sagebrush Steppe Ecosystems  

SciTech Connect (OSTI)

Evaluating vegetation cover is an important factor in understanding the sustainability of many ecosystems. Methods that have sufficient accuracy and improved cost efficiency could dramatically alter how biotic resources are monitored on both public and private lands. This will be of interest to land managers because there are rarely enough resource specialists or funds available for comprehensive ground evaluations. In this project, unmanned helicopters were used to collect still-frame imagery to assess vegetation cover during May, June, and July in 2005. The images were used to estimate percent cover for six vegetative cover classes (shrub, dead shrub, grass, forbs, litter, and bare ground). The field plots were located on the INL site west of Idaho Falls, Idaho. Ocular assessments of digital imagery were performed using a software program called SamplePoint, and the results were compared against field measurements collected using a point-frame method to assess accuracy. The helicopter imagery evaluation showed a high degree of agreement with field cover class values for litter, bare ground, and grass, and reasonable agreement for dead shrubs. Shrub cover was often overestimated and forbs were generally underestimated. The helicopter method took 45% less time than the field method to set plots and collect and analyze data. This study demonstrates that UAV technology provides a viable method for monitoring vegetative cover on rangelands in less time and with lower costs. Tradeoffs between cost and accuracy are critical management decisions that are important when managing vegetative conditions across vast sagebrush ecosystems throughout the Intermountain West.

Robert P. Breckenridge; Maxine Dakins; Stephen Bunting; Jerry Harbour; Randy Lee

2012-07-01T23:59:59.000Z