Sample records for vapor high pressure

  1. OPTIMAL DESIGN OF A HIGH PRESSURE ORGANOMETALLIC CHEMICAL VAPOR DEPOSITION REACTOR

    E-Print Network [OSTI]

    OPTIMAL DESIGN OF A HIGH PRESSURE ORGANOMETALLIC CHEMICAL VAPOR DEPOSITION REACTOR K.J. BACHMANN vapor deposition (HPOMCVD) reactor for use in thin film crystal growth. The advantages of such a reactor decomposition pressures and increased control over local stoichiometry and defect formation. While we focus here

  2. Preconcentrator with high volume chiller for high vapor pressure particle detection

    DOE Patents [OSTI]

    Linker, Kevin L

    2013-10-22T23:59:59.000Z

    Apparatus and method for collecting particles of both high and low vapor pressure target materials entrained in a large volume sample gas stream. Large volume active cooling provides a cold air supply which is mixed with the sample gas stream to reduce the vapor pressure of the particles. In embodiments, a chiller cools air from ambient conditions to 0-15.degree. C. with the volumetric flow rate of the cold air supply being at least equal to the volumetric flow rate of the sample gas stream. In further embodiments an adsorption media is heated in at least two stages, a first of which is below a threshold temperature at which decomposition products of the high vapor pressure particle are generated.

  3. VAPOR PRESSURES AND HEATS OF VAPORIZATION OF PRIMARY COAL TARS

    SciTech Connect (OSTI)

    Eric M. Suuberg; Vahur Oja

    1997-07-01T23:59:59.000Z

    This project had as its main focus the determination of vapor pressures of coal pyrolysis tars. It involved performing measurements of these vapor pressures and from them, developing vapor pressure correlations suitable for use in advanced pyrolysis models (those models which explicitly account for mass transport limitations). This report is divided into five main chapters. Each chapter is a relatively stand-alone section. Chapter A reviews the general nature of coal tars and gives a summary of existing vapor pressure correlations for coal tars and model compounds. Chapter B summarizes the main experimental approaches for coal tar preparation and characterization which have been used throughout the project. Chapter C is concerned with the selection of the model compounds for coal pyrolysis tars and reviews the data available to us on the vapor pressures of high boiling point aromatic compounds. This chapter also deals with the question of identifying factors that govern the vapor pressures of coal tar model materials and their mixtures. Chapter D covers the vapor pressures and heats of vaporization of primary cellulose tars. Chapter E discusses the results of the main focus of this study. In summary, this work provides improved understanding of the volatility of coal and cellulose pyrolysis tars. It has resulted in new experimentally verified vapor pressure correlations for use in pyrolysis models. Further research on this topic should aim at developing general vapor pressure correlations for all coal tars, based on their molecular weight together with certain specific chemical characteristics i.e. hydroxyl group content.

  4. To estimate vapor pressure easily

    SciTech Connect (OSTI)

    Yaws, C.L.; Yang, H.C. (Lamar Univ., Beaumont, TX (USA))

    1989-10-01T23:59:59.000Z

    Vapor pressures as functions of temperature for approximately 700 major organic chemical compounds are given. The tabulation also gives the temperature range for which the data are applicable. Minimum and maximum temperatures are denoted by TMIN and TMAX. The Antoine equation that correlates vapor pressure as a function of temperature is described. A representative comparison of calculated and actual data values for vapor pressure is shown for ethyl alcohol. The coefficient tabulation is based on both literature (experimental data) and estimated values.

  5. Enthalpies of Vaporization and Vapor Pressures of Some Deuterated Hydrocarbons. Liquid-Vapor Pressure Isotope Effects

    E-Print Network [OSTI]

    Chickos, James S.

    Enthalpies of Vaporization and Vapor Pressures of Some Deuterated Hydrocarbons. Liquid hydrocarbons and their perdeuterated analogues have been determined by correlation-gas chromatography of cyclohexane-d12 and benzene-d6. Other hydrocarbons studied include the perdeuterated forms of hexane, toluene

  6. Pore evolution during high pressure atomic vapor deposition D. D. Hass Y. Y. Yang H. N. G. Wadley

    E-Print Network [OSTI]

    Wadley, Haydn

    The development of physical vapor deposition systems that employ inert gas jets to entrain and deposit atomic conditions can contain a higher volume fraction of porosity and a different pore morphology to coatings created by conventional, low pressure (\\10-4 Pa) deposition processes. A recent direct simulation Monte

  7. Vapor Pressure measurements for dichlorosilane

    E-Print Network [OSTI]

    Morris, Tony Knimbula

    1997-01-01T23:59:59.000Z

    stainless steel surface inside the head. In the user's manual, one of the sections talked about this window and the plugging screw below it. This screw was provided to empty any fluid that might have gotten into that section of the head behind the window... due to being tilted. Immediately afler emptying the fluid, the balance was still unsteady. After allowing the area to dry by leaving the plug off for a few days, the balance readings were stable. It tumed out that the pressure would somehow push...

  8. Atmospheric Pressure Chemical Vapor Deposition of High Silica SiO2-TiO2 Antireflective Thin Films for Glass Based Solar Panels

    SciTech Connect (OSTI)

    Klobukowski, Erik R [ORNL; Tenhaeff, Wyatt E [ORNL; McCamy, James [PPG; Harris, Caroline [PPG; Narula, Chaitanya Kumar [ORNL

    2013-01-01T23:59:59.000Z

    The atmospheric pressure chemical vapor deposition (APCVD) of SiO2-TiO2 thin films employing [[(tBuO)3Si]2O-Ti(OiPr)2], which can be prepared from commercially available materials, results in antireflective thin films on float glass under industrially relevant manufacturing conditions. It was found that while the deposition temperature had an effect on the SiO2:TiO2 ratio, the thickness was dependent on the time of deposition. This study shows that it is possible to use APCVD employing a single source precursor containing titanium and silicon to produce thin films on float glass with high SiO2:TiO2 ratios.

  9. A new vapor pressure equation originating at the critical point

    E-Print Network [OSTI]

    Nuckols, James William

    1976-01-01T23:59:59.000Z

    - tence curve has been developed from critical scaling theory. The agreement between published vapor pressures and vapor pressures predicted by this equation is very good, especially in the critical region where many other vapor pressure equations fail... vapor pressure data f' or Ar, N2, 02H6, and H20, w1th the parameters ai to a being determined by an unweighted least squares curve 5 fit. The method of least squares has been described adequately elsewhere, e. g. Wylie (1966), and the theory w111...

  10. Analysis of crude oil vapor pressures at the U.S. Strategic Petroleum Reserve.

    SciTech Connect (OSTI)

    Rudeen, David Keith (GRAM, Inc., Albuquerque, NM); Lord, David L.

    2005-08-01T23:59:59.000Z

    Crude oil storage caverns at the U.S. Strategic Petroleum Reserve (SPR) are solution-mined from subsurface salt domes along the U.S. Gulf Coast. While these salt domes exhibit many attractive characteristics for large-volume, long-term storage of oil such as low cost for construction, low permeability for effective fluids containment, and secure location deep underground, they also present unique technical challenges for maintaining oil quality within delivery standards. The vapor pressures of the crude oils stored at SPR tend to increase with storage time due to the combined effects of geothermal heating and gas intrusion from the surrounding salt. This presents a problem for oil delivery offsite because high vapor-pressure oil may lead to excessive atmospheric emissions of hydrocarbon gases that present explosion hazards, health hazards, and handling problems at atmospheric pressure. Recognizing this potential hazard, the U.S. Department of Energy, owner and operator of the SPR, implemented a crude oil vapor pressure monitoring program that collects vapor pressure data for all the storage caverns. From these data, DOE evaluates the rate of change in vapor pressures of its oils in the SPR. Moreover, DOE implemented a vapor pressure mitigation program in which the oils are degassed periodically and will be cooled immediately prior to delivery in order to reduce the vapor pressure to safe handling levels. The work described in this report evaluates the entire database since its origin in 1993, and determines the current levels of vapor pressure around the SPR, as well as the rate of change for purposes of optimizing both the mitigation program and meeting safe delivery standards. Generally, the rate of vapor pressure increase appears to be lower in this analysis than reported in the past and, problematic gas intrusion seems to be limited to just a few caverns. This being said, much of the current SPR inventory exceeds vapor pressure delivery guidelines and must be degassed and cooled in order to meet current delivery standards.

  11. Temperature dependent vapor pressures of chlorinated catechols, syringols, and syringaldehydes

    SciTech Connect (OSTI)

    Lei, Y.D.; Shiu, W.Y.; Boocock, D.G.B. [Univ. of Toronto, Ontario (Canada). Dept. of Chemical Engineering and Applied Chemistry] [Univ. of Toronto, Ontario (Canada). Dept. of Chemical Engineering and Applied Chemistry; Wania, F. [WECC Wania Environmental Chemists Corp., Toronto, Ontario (Canada)] [WECC Wania Environmental Chemists Corp., Toronto, Ontario (Canada)

    1999-03-01T23:59:59.000Z

    The vapor pressures of nine chlorinated catechols, syringols, and syringaldehydes were determined as a function of temperature with a gas chromatographic retention time technique. The vapor pressures at 298.15 K were in the range of 0.02--1 Pa, and the enthalpies of vaporization, between 68 and 82 kJ/mol. The validity of the technique was established by a calibration involving four chlorinated phenols with well-known vapor pressures. Using these data and previously reported solubility data, Henry`s law constants for these substances and some chlorinated guaiacols and veratrols were estimated. The vapor pressure of these substances tends to decrease with increasing polarity and an increasing number of chlorine atoms. Henry`s law constants decrease sharply with increasing polarity, suggesting that methylation can result in a significant increase in a chemical`s potential for volatilization from water.

  12. Effect of reactor pressure on the electrical and structural properties of InN epilayers grown by high-pressure chemical vapor deposition

    E-Print Network [OSTI]

    Nabben, Reinhard

    Effect of reactor pressure on the electrical and structural properties of InN epilayers grown://avspublications.org/jvsta/about/rights_and_permissions #12;Effect of reactor pressure on the electrical and structural properties of InN epilayers grown-atmospheric reactor pressures (2.5­18.5 bar) on the electrical and structural properties of InN epilayers deposited

  13. Bilayer graphene growth by low pressure chemical vapor deposition on copper foil

    E-Print Network [OSTI]

    Fang, Wenjing, S.M. Massachusetts Institute of Technology

    2012-01-01T23:59:59.000Z

    Successfully integrating graphene in standard processes for applications in electronics relies on the synthesis of high-quality films. In this work we study Low Pressure Chemical Vapor Deposition (LPCVD) growth of bilayer ...

  14. Controlling the vapor pressure of a mercury lamp

    DOE Patents [OSTI]

    Grossman, Mark W. (Belmont, MA); George, William A. (Rockport, MA)

    1988-01-01T23:59:59.000Z

    The invention described herein discloses a method and apparatus for controlling the Hg vapor pressure within a lamp. This is done by establishing and controlling two temperature zones within the lamp. One zone is colder than the other zone. The first zone is called the cold spot. By controlling the temperature of the cold spot, the Hg vapor pressure within the lamp is controlled. Likewise, by controlling the Hg vapor pressure of the lamp, the intensity and linewidth of the radiation emitted from the lamp is controlled.

  15. Evaporation monitoring and composition control of alloy systems with widely differing vapor pressures

    SciTech Connect (OSTI)

    Anklam, T.M.; Berzins, L.V.; Braun, D.G.; Haynam, C.; McClelland, M.A.; Meier, T.

    1994-10-01T23:59:59.000Z

    Lawrence Livermore National Laboratory is developing sensors and controls to improve and extend electron beam materials processing technology to alloy systems with constituents of widely varying vapor pressure. The approach under development involves using tunable lasers to measure the density and composition of the vapor plume. A laser based vaporizer control system for vaporization of a uranium-iron alloy has been previously demonstrated in multi-hundred hour, high rate vaporization experiments at LLNL. This paper reviews the design and performance of the uranium vaporization sensor and control system and discusses the extension of the technology to monitoring of uranium vaporization. Data is presented from an experiment in which titanium wire was fed into a molten niobium pool. Laser data is compared to deposited film composition and film cross sections. Finally, the potential for using this technique for composition control in melting applications is discussed.

  16. Evaporation monitoring and composition control of alloy systems with widely differing vapor pressures

    SciTech Connect (OSTI)

    Anklam, T.M.; Berzins, L.V.; Braun, D.G.; Haynam, C.; McClelland, M.A.; Meier, T. [Lawrence Livermore National Lab., CA (United States)

    1994-12-31T23:59:59.000Z

    Lawrence Livermore National Laboratory is developing sensors and controls to improve and extend electron beam materials processing technology to alloy systems with constituents of widely varying vapor pressure. The approach under development involves using tunable lasers to measure the density and composition of the vapor plume. A laser based vaporizer control system for vaporization of a uranium-iron alloy has been previously demonstrated in multi-hundred hour, high rate vaporization experiments at LLNL. This paper reviews the design and performance of the uranium vaporization sensor and control system and discusses the extension of the technology to monitoring of titanium vaporization. Data is presented from an experiment in which titanium wire was fed into a molten niobium pool. Laser data is compared to deposited film composition and film cross sections. Finally, the potential for using this technique for composition control in melting applications is discussed.

  17. Optimal determination of the vapor pressure critical exponent

    E-Print Network [OSTI]

    Walton, Clifford Wayne

    1977-01-01T23:59:59.000Z

    , 1969), while scaling theory predicts about 0. 1 (Vicentini-Missoni et al. , 1969; Widom and Rowlinson, 1970). The object of this study was to determine the optimum value of 0 by means of a least squares fit of various nonanalytic vapor pressure... onal : cj ence Foundation, Grant ENG76-00692, is acknowl- edged. vi TABLE OF CONTENTS Page SCOPE. CONCLUSIONS AND SIGNII'ICANCE INTRODUCTION Theory. Development of Vapor Pressure Equations PROCEDURE. Curve Fit Method (CFN). Numerical...

  18. Hypothetical Thermodynamic Properties. Subcooled Vaporization Enthalpies and Vapor Pressures of Polyaromatic Hydrocarbons

    E-Print Network [OSTI]

    Chickos, James S.

    of Polyaromatic Hydrocarbons William Hanshaw, Marjorie Nutt, and James S. Chickos* Department of Chemistry and liquid vapor pressures from T ) 298.15 K to T ) 510 K of a series of polyaromatic hydrocarbons have been protocols are also made, and agreement generally is quite good. Introduction Polyaromatic hydrocarbons (PAHs

  19. Method and apparatus to measure vapor pressure in a flow system

    DOE Patents [OSTI]

    Grossman, Mark W. (Belmont, MA); Biblarz, Oscar (Swampscott, MA)

    1991-01-01T23:59:59.000Z

    The present invention is directed to a method for determining, by a condensation method, the vapor pressure of a material with a known vapor pressure versus temperature characteristic, in a flow system particularly in a mercury isotope enrichment process.

  20. VAPOR PRESSURE ISOTOPE EFFECTS IN THE MEASUREMENT OF ENVIRONMENTAL TRITIUM SAMPLES.

    SciTech Connect (OSTI)

    Kuhne, W.

    2012-12-03T23:59:59.000Z

    Standard procedures for the measurement of tritium in water samples often require distillation of an appropriate sample aliquot. This distillation process may result in a fractionation of tritiated water and regular light water due to the vapor pressure isotope effect, introducing either a bias or an additional contribution to the total tritium measurement uncertainty. The magnitude of the vapor pressure isotope effect is characterized as functions of the amount of water distilled from the sample aliquot and the heat settings for the distillation process. The tritium concentration in the distillate is higher than the tritium concentration in the sample early in the distillation process, it then sharply decreases due to the vapor pressure isotope effect and becomes lower than the tritium concentration in the sample, until the high tritium concentration retained in the boiling flask is evaporated at the end of the process. At that time, the tritium concentration in the distillate again overestimates the sample tritium concentration. The vapor pressure isotope effect is more pronounced the slower the evaporation and distillation process is conducted; a lower heat setting during the evaporation of the sample results in a larger bias in the tritium measurement. The experimental setup used and the fact that the current study allowed for an investigation of the relative change in vapor pressure isotope effect in the course of the distillation process distinguish it from and extend previously published measurements. The separation factor as a quantitative measure of the vapor pressure isotope effect is found to assume values of 1.034 {+-} 0.033, 1.052 {+-} 0.025, and 1.066 {+-} 0.037, depending on the vigor of the boiling process during distillation of the sample. A lower heat setting in the experimental setup, and therefore a less vigorous boiling process, results in a larger value for the separation factor. For a tritium measurement in water samples, this implies that the tritium concentration could be underestimated by 3 - 6%.

  1. High temperature pressure gauge

    DOE Patents [OSTI]

    Echtler, J. Paul (Pittsburgh, PA); Scandrol, Roy O. (Library, PA)

    1981-01-01T23:59:59.000Z

    A high temperature pressure gauge comprising a pressure gauge positioned in fluid communication with one end of a conduit which has a diaphragm mounted in its other end. The conduit is filled with a low melting metal alloy above the diaphragm for a portion of its length with a high temperature fluid being positioned in the remaining length of the conduit and in the pressure gauge.

  2. High pressure melt ejection

    SciTech Connect (OSTI)

    Tarbell, W.W.; Brockmann, J.E.; Pilch, M.

    1983-01-01T23:59:59.000Z

    Recent probabilistic risk assessments have identified the potential for reactor pressure vessel failure while the reactor coolant system is at elevated pressure. The analyses postulate that the blowdown of steam and hydrogen into the reactor cavity will cause the core material to be swept from the cavity region into the containment building. The High Pressure Melt Streaming (HIPS) program is an experimental study of the high pressure ejection of molten material and subsequent interactions within a concrete cavity. The program focuses on using prototypic system conditions and scaled models of reactor geometries to accurately simulate the ex-vessel processes during high-pressure accident sequences. Scaling analyses of the experiment show that the criteria established for core debris removal from the cavity are met or exceeded. Tests are performed at two scales, representing 1/10th and 1/20th linear reproductions of the Zion reactor plant. Results of the 1/20th scale tests are presented.

  3. High pressure counterflow CHF.

    E-Print Network [OSTI]

    Walkush, Joseph Patrick

    1975-01-01T23:59:59.000Z

    This is a report of the experimental results of a program in countercurrent flow critical heat flux. These experiments were performed with Freon 113 at 200 psia in order to model a high pressure water system. An internally ...

  4. Method and apparatus to measure vapor pressure in a flow system

    DOE Patents [OSTI]

    Grossman, M.W.; Biblarz, O.

    1991-10-15T23:59:59.000Z

    The present invention is directed to a method for determining, by a condensation method, the vapor pressure of a material with a known vapor pressure versus temperature characteristic, in a flow system particularly in a mercury isotope enrichment process. 2 figures.

  5. High pressure furnace

    DOE Patents [OSTI]

    Morris, D.E.

    1993-09-14T23:59:59.000Z

    A high temperature high pressure furnace has a hybrid partially externally heated construction. A metallic vessel fabricated from an alloy having a composition of at least 45% nickel, 15% chrome, and 10% tungsten is utilized (the preferred alloy including 55% nickel, 22% chrome, 14% tungsten, 2% molybdenum, 3% iron (maximum) and 5% cobalt (maximum)). The disclosed alloy is fabricated into 11/4 or 2 inch, 32 mm or 50 mm bar stock and has a length of about 22 inches, 56 cm. This bar stock has an aperture formed therein to define a closed high temperature, high pressure oxygen chamber. The opposite and closed end of the vessel is provided with a small blind aperture into which a thermocouple can be inserted. The closed end of the vessel is inserted into an oven, preferably heated by standard nickel chrome electrical elements and having a heavily insulated exterior. 19 figures.

  6. High pressure oxygen furnace

    DOE Patents [OSTI]

    Morris, Donald E. (Kensington, CA)

    1992-01-01T23:59:59.000Z

    A high temperature high pressure oxygen furnace having a hybrid partially externally heated construction is disclosed. A metallic bar fabricated from an alloy having a composition of at least 45% nickel, 15% chrome, and 10% tungsten is utilized (the preferred alloy including 55% nickel, 22% chrome, 14% tungsten, 2% molybdenum, 3% iron (maximum) and 5% cobalt (maximum). The disclosed alloy is fabricated into 11/4 inch bar stock and has a length of about 17 inches. This bar stock is gun drilled for over 16 inches of its length with 0.400 inch aperture to define a closed high temperature, high pressure oxygen chamber. The opposite and closed end of the bar is provided with a small support aperture into which both a support and a thermocouple can be inserted. The closed end of the gun drilled bar is inserted into an oven, preferably heated by standard nickel chrome electrical elements and having a heavily insulated exterior.

  7. High pressure oxygen furnace

    DOE Patents [OSTI]

    Morris, D.E.

    1992-07-14T23:59:59.000Z

    A high temperature high pressure oxygen furnace having a hybrid partially externally heated construction is disclosed. A metallic bar fabricated from an alloy having a composition of at least 45% nickel, 15% chrome, and 10% tungsten is utilized, the preferred alloy including 55% nickel, 22% chrome, 14% tungsten, 2% molybdenum, 3% iron (maximum) and 5% cobalt (maximum). The disclosed alloy is fabricated into 11/4 inch bar stock and has a length of about 17 inches. This bar stock is gun drilled for over 16 inches of its length with 0.400 inch aperture to define a closed high temperature, high pressure oxygen chamber. The opposite and closed end of the bar is provided with a small support aperture into which both a support and a thermocouple can be inserted. The closed end of the gun drilled bar is inserted into an oven, preferably heated by standard nickel chrome electrical elements and having a heavily insulated exterior. 5 figs.

  8. High pressure furnace

    DOE Patents [OSTI]

    Morris, Donald E. (Kensington, CA)

    1993-01-01T23:59:59.000Z

    A high temperature high pressure furnace has a hybrid partially externally heated construction. A metallic vessel fabricated from an alloy having a composition of at least 45% nickel, 15% chrome, and 10% tungsten is utilized (the preferred alloy including 55% nickel, 22% chrome, 14% tungsten, 2% molybdenum, 3% iron (maximum) and 5% cobalt (maximum). The disclosed alloy is fabricated into 11/4 or 2 inch, 32 mm or 50 mm bar stock and has a length of about 22 inches, 56 cm. This bar stock has an aperture formed therein to define a closed high temperature, high pressure oxygen chamber. The opposite and closed end of the vessel is provided with a small blind aperture into which a thermocouple can be inserted. The closed end of the vessel is inserted into an oven, preferably heated by standard nickel chrome electrical elements and having a heavily insulated exterior.

  9. U.S. Strategic Petroleum Reserve Vapor Pressure Committee 2009 annual report.

    SciTech Connect (OSTI)

    Allen, Ray (Allen Energy Services, Inc., Longview, TX); Eldredge, Lisa (DynMcDermott Petroleum Operations, Harahan, LA); DeLuca, Charles (DynMcDermott Petroleum Operations, Harahan, LA); Mihalik, Patrick (DynMcDermott Petroleum Operations, Harahan, LA); Maldonado, Julio (U.S. Department of Energy, Harahan, LA); Lord, David L.; Rudeen, David Keith (GRAM, Inc., Albuquerque, NM); Berndsen, Gerard (U.S. Department of Energy, Harahan, LA)

    2010-05-01T23:59:59.000Z

    This report comprises an annual summary of activities under the U.S. Strategic Petroleum Reserve (SPR) Vapor Pressure Committee in FY2009. The committee provides guidance to senior project management on the issues of crude oil vapor pressure monitoring nd mitigation. The principal objectives of the vapor pressure program are, in the event of an SPR drawdown, to minimize the impact on the environment and assure worker safety and public health from crude oil vapor emissions. The annual report reviews key program areas ncluding monitoring program status, mitigation program status, new developments in measurements and modeling, and path forward including specific recommendations on cavern sampling for the next year. The contents of this report were first presented to SPR senior anagement in December 2009, in a deliverable from the vapor pressure committee. The current SAND report is an adaptation for the Sandia technical audience.

  10. Nitrogen at very high pressure

    SciTech Connect (OSTI)

    Nellis, W.J.

    1987-07-01T23:59:59.000Z

    High-pressure results for nitrogen are reviewed and discussed in terms of phenomena that occur at extreme conditions.

  11. Single- and few-layer graphene by ambient pressure chemical vapor deposition on nickel

    E-Print Network [OSTI]

    Reina Ceeco, Alfonso

    2010-01-01T23:59:59.000Z

    An ambient pressure chemical vapor deposition (APCVD) process is used to fabricate graphene based films consisting of one to several graphene layers across their area. Polycrystalline Ni thin films are used and the graphene ...

  12. High-pressure neutron diffraction

    SciTech Connect (OSTI)

    Xu, Hongwu [Los Alamos National Laboratory

    2011-01-10T23:59:59.000Z

    This lecture will cover progress and prospect of applications of high-pressure neutron diffraction techniques to Earth and materials sciences. I will first introduce general high-pressure research topics and available in-situ high-pressure techniques. Then I'll talk about high-pressure neutron diffraction techniques using two types of pressure cells: fluid-driven and anvil-type cells. Lastly, I will give several case studies using these techniques, particularly, those on hydrogen-bearing materials and magnetic transitions.

  13. Integrated rig for the production of boron nitride nanotubes via the pressurized vapor-condenser method

    DOE Patents [OSTI]

    Smith, Michael W; Jordan, Kevin C

    2014-03-25T23:59:59.000Z

    An integrated production apparatus for production of boron nitride nanotubes via the pressure vapor-condenser method. The apparatus comprises: a pressurized reaction chamber containing a continuously fed boron containing target having a boron target tip, a source of pressurized nitrogen and a moving belt condenser apparatus; a hutch chamber proximate the pressurized reaction chamber containing a target feed system and a laser beam and optics.

  14. High Temperature High Pressure Thermodynamic Measurements for Coal Model Compounds

    SciTech Connect (OSTI)

    John C. Chen; Vinayak N. Kabadi

    1998-11-12T23:59:59.000Z

    The overall objective of this project is to develop a better thermodynamic model for predicting properties of high-boiling coal derived liquids, especially the phase equilibria of different fractions at elevated temperatures and pressures. The development of such a model requires data on vapor-liquid equilibria (VLE), enthalpy, and heat capacity which would be experimentally determined for binary systems of coal model compounds and compiled into a database. The data will be used to refine existing models such as UNIQUAC and UNIFAC. The flow VLE apparatus designed and built for a previous project was upgraded and recalibrated for data measurements for thk project. The modifications include better and more accurate sampling technique and addition of a digital recorder to monitor temperature, pressure and liquid level inside the VLE cell. VLE data measurements for system benzene-ethylbenzene have been completed. The vapor and liquid samples were analysed using the Perkin-Elmer Autosystem gas chromatography.

  15. Measurement of alkali-vapor emission from pressurized fluidized-bed combustion of Illinois coals

    SciTech Connect (OSTI)

    Lee, S.H.D.; Teats, F.G.; Swift, W.M. (Argonne National Lab., IL (United States)); Banerjee, D.D. (Illinois Clean Coal Inst., Carterville, IL (United States))

    1993-01-01T23:59:59.000Z

    Two Illinois Herrin No. 6 coals and one Illinois Springfield No. 5 coal were separately combusted in a laboratory-scale (15-cm dia) pressurized fluidized-bed combustor (PFBC) combined with an alkali sorber. These coals were combusted in a fluidized bed of Tymochtee dolomite at temperatures ranging from 910 to 950[degree]C and a system pressure of 9.2 atm absolute. Alkali-vapor emission (Na and K) in the PFBC flue gas was determined by the analytical activated-bauxite sorber bed technique developed at Argonne National Laboratory. The test results showed that sodium is the major alkali-vapor species present in the PFBC flue gas, and that the level of sodium-vapor emission increases linearly with both Na and Cl contents in the coals. This suggests that the sodium-vapor emission results from direct vaporization of NaCl present in the coals. The measured alkali-vapor concentration (Na + K), 67 to 190 ppbW, is more than 2.5 times greater than the allowable alkali limit of 24 ppb for an industrial gas turbine. Combusting these coals in a PFBC for power generation may require developing a method to control alkali vapors.

  16. Measurement of alkali-vapor emission from pressurized fluidized-bed combustion of Illinois coals

    SciTech Connect (OSTI)

    Lee, S.H.D.; Teats, F.G.; Swift, W.M. [Argonne National Lab., IL (United States); Banerjee, D.D. [Illinois Clean Coal Inst., Carterville, IL (United States)

    1993-04-01T23:59:59.000Z

    Two Illinois Herrin No. 6 coals and one Illinois Springfield No. 5 coal were separately combusted in a laboratory-scale (15-cm dia) pressurized fluidized-bed combustor (PFBC) combined with an alkali sorber. These coals were combusted in a fluidized bed of Tymochtee dolomite at temperatures ranging from 910 to 950{degree}C and a system pressure of 9.2 atm absolute. Alkali-vapor emission (Na and K) in the PFBC flue gas was determined by the analytical activated-bauxite sorber bed technique developed at Argonne National Laboratory. The test results showed that sodium is the major alkali-vapor species present in the PFBC flue gas, and that the level of sodium-vapor emission increases linearly with both Na and Cl contents in the coals. This suggests that the sodium-vapor emission results from direct vaporization of NaCl present in the coals. The measured alkali-vapor concentration (Na + K), 67 to 190 ppbW, is more than 2.5 times greater than the allowable alkali limit of 24 ppb for an industrial gas turbine. Combusting these coals in a PFBC for power generation may require developing a method to control alkali vapors.

  17. Electrokinetically pumped high pressure sprays

    DOE Patents [OSTI]

    Schoeniger, Joseph S. (Oakland, CA); Paul, Phillip H. (Livermore, CA); Schoeniger, Luke (Pittsford, NY)

    2002-01-01T23:59:59.000Z

    An electrokinetic pump capable of producing high pressure is combined with a nozzle having a submicron orifice to provide a high pressure spray device. Because of its small size, the device can be contained within medical devices such as an endoscope for delivering biological materials such as DNA, chemo therapeutic agents, or vaccines to tissues and cells.

  18. High pressure storage vessel

    DOE Patents [OSTI]

    Liu, Qiang

    2013-08-27T23:59:59.000Z

    Disclosed herein is a composite pressure vessel with a liner having a polar boss and a blind boss a shell is formed around the liner via one or more filament wrappings continuously disposed around at least a substantial portion of the liner assembly combined the liner and filament wrapping have a support profile. To reduce susceptible to rupture a locally disposed filament fiber is added.

  19. Improved measurement of crude oil vapor pressure via PVT study methods

    SciTech Connect (OSTI)

    Roehner, R. [Alyeska Pipeline Service Co., Anchorage, AK (United States); Wetzel, G.; Stonestreet, W.; Lievios, J.; Reed, D.

    1996-12-31T23:59:59.000Z

    A technical task force created by owner companies of the Trans-Alaska Pipeline System (TAPS) including BP Pipelines (Alaska), and Arco Transportation Alaska, Inc., and Alyeska Pipeline Service Company (APSC), the operator of TAPS, have investigated new technology for measuring the saturated liquid bubble point vapor pressure (BPVP) of crude oils. This technology is based on Pressure-Volume-Temperature (PVT) Cell study methods and consists of an on-line Vapor Pressure Analyzer (VPA) developed by Arco Oil & Gas Company and marketed by Fluid Data (TVP-1000), and a mercury-free automated PVT lab system (RUSKA 2370 Lab System) marketed by Ruska Instrument Corporation and modified to meet APSC requirements. In this methodology, the BPVP for the multicomponent fluid crude oil is defined and approximated by the intersection of the liquid compressibility and two phase lines on the isothermal pressure-volume (PV) curve for the fluid. The Task Force finds that this new technology provides saturated liquid bubble point vapor pressure values of TAPS crude oils which differ by 15 to 95 kPa from True Vapor Pressure (TVP) values obtained using API Publication 2517, Figure 18B-Equation for of Crude Oils With A Reid Vapor Pressure of 2-15 Pounds per Square Inch and corresponding RVP data from the crude oils tested. The range in difference between the BPVP and the TVP for each of five different TAPS crude oils tested was found to be due to differences in crude oil composition. 3 refs., 1 fig., 1 tab.

  20. Alkali vapor pressure modulation on the 100 ms scale in a single-cell vacuum system for cold atom experiments

    SciTech Connect (OSTI)

    Dugrain, Vincent; Reichel, Jakob [Laboratoire Kastler Brossel, ENS, UPMC, CNRS, 24 rue Lhomond, 75005 Paris (France); Rosenbusch, Peter [LNE-SYRTE, Observatoire de Paris, CNRS, UPMC, 61 av de l’Observatoire, 75014 Paris (France)

    2014-08-15T23:59:59.000Z

    We describe and characterize a device for alkali vapor pressure modulation on the 100 ms timescale in a single-cell cold atom experiment. Its mechanism is based on optimized heat conduction between a current-modulated alkali dispenser and a heat sink at room temperature. We have studied both the short-term behavior during individual pulses and the long-term pressure evolution in the cell. The device combines fast trap loading and relatively long trap lifetime, enabling high repetition rates in a very simple setup. These features make it particularly suitable for portable atomic sensors.

  1. High volume fuel vapor release valve

    SciTech Connect (OSTI)

    Gimby, D.R.

    1991-09-03T23:59:59.000Z

    This patent describes a fuel vapor release valve for use in a vehicle fuel system. It comprises a valve housing 10 placed in a specific longitudinal orientation, the valve housing 10 defining an interior cavity 22 having an inlet 20 for admitting fuel vapor and an outlet 14 for discharging such fuel vapor; a valve member 24 positioned in the cavity 22 for movement between an outlet 14 opening position and an outlet 14 closing position, the valve member 24 including a cap member 34 having a seat surface 36 for mating with the outlet 14 and an orifice 42 extending through the cap member 34 providing a passageway from the outlet 14 to the cavity 22, the orifice 42 extending through the cap member 34 providing a passageway from the outlet 14 to the cavity 22, the orifice 42 having a lesser radius than the outlet 14; the valve member 24 further including a plug member 30 engaged with the cap member 34 for movement between an orifice 42 opening position and an orifice 42 closing position; and, a valve housing tilt responsive means for moving the valve member 24 to an outlet 14 and orifice 42 closing position in response to tilting of the valve 10 about its longitudinal axis whereby, upon the return of the valve 10 to its specified longitudinal orientation, the plug member 30 first moves to an orifice 42 opening position and the cap member 34 subsequently moves to an outlet 14 opening position.

  2. Steam Oxidation at High Pressure

    SciTech Connect (OSTI)

    Holcomb, Gordon R. [NETL; Carney, Casey [URS

    2013-07-19T23:59:59.000Z

    A first high pressure test was completed: 293 hr at 267 bar and 670{degrees}C; A parallel 1 bar test was done for comparison; Mass gains were higher for all alloys at 267 bar than at 1 bar; Longer term exposures, over a range of temperatures and pressures, are planned to provide information as to the commercial implications of pressure effects; The planned tests are at a higher combination of temperatures and pressures than in the existing literature. A comparison was made with longer-term literature data: The short term exposures are largely consistent with the longer-term corrosion literature; Ferritic steels--no consistent pressure effect; Austenitic steels--fine grain alloys less able to maintain protective chromia scale as pressure increases; Ni-base alloys--more mass gains above 105 bar than below. Not based on many data points.

  3. Atmospheric pressure chemical vapor deposition of TiN from tetrakis(dimethylamido)titanium and ammonia

    E-Print Network [OSTI]

    of titanium in a nitrogen atmosphere forms TiN with only a slight dependence on substrate temperatureAtmospheric pressure chemical vapor deposition of TiN from tetrakis(dimethylamido)titanium, Massachusetts 02138 (Received 15 December 1994; accepted 28 October 1995) Near stoichiometric titanium nitride

  4. Electrokinetic high pressure hydraulic system

    DOE Patents [OSTI]

    Paul, Phillip H. (Livermore, CA); Rakestraw, David J. (Fremont, CA)

    2000-01-01T23:59:59.000Z

    A compact high pressure hydraulic pump having no moving mechanical parts for converting electric potential to hydraulic force. The electrokinetic pump, which can generate hydraulic pressures greater than 2500 psi, can be employed to compress a fluid, either liquid or gas, and manipulate fluid flow. The pump is particularly useful for capillary-base systems. By combining the electrokinetic pump with a housing having chambers separated by a flexible member, fluid flow, including high pressure fluids, is controlled by the application of an electric potential, that can vary with time.

  5. Graphene chemical vapor deposition at very low pressure: The impact of substrate surface self-diffusion in domain shape

    SciTech Connect (OSTI)

    Cunha, T. H. R.; Ek-Weis, J.; Lacerda, R. G.; Ferlauto, A. S., E-mail: ferlauto@fisica.ufmg.br [Department of Physics, Federal University of Minas Gerais, Belo Horizonte 31270-901 (Brazil)

    2014-08-18T23:59:59.000Z

    The initial stages of graphene chemical vapor deposition at very low pressures (<10{sup ?5?}Torr) were investigated. The growth of large graphene domains (?up to 100??m) at very high rates (up to 3??m{sup 2} s{sup ?1}) has been achieved in a cold-wall reactor using a liquid carbon precursor. For high temperature growth (>900?°C), graphene grain shape and symmetry were found to depend on the underlying symmetry of the Cu crystal, whereas for lower temperatures (<900?°C), mostly rounded grains are observed. The temperature dependence of graphene nucleation density was determined, displaying two thermally activated regimes, with activation energy values of 6?±?1?eV for temperatures ranging from 900?°C to 960?°C and 9?±?1?eV for temperatures above 960?°C. The comparison of such dependence with the temperature dependence of Cu surface self-diffusion suggests that graphene growth at high temperatures and low pressures is strongly influenced by copper surface rearrangement. We propose a model that incorporates Cu surface self-diffusion as an essential process to explain the orientation correlation between graphene and Cu crystals, and which can clarify the difference generally observed between graphene domain shapes in atmospheric-pressure and low-pressure chemical vapor deposition.

  6. High Pressure Hydrogen Materials Compatibility of Piezoelectric...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Pressure Hydrogen Materials Compatibility of Piezoelectric Films. High Pressure Hydrogen Materials Compatibility of Piezoelectric Films. Abstract: Abstract: Hydrogen is being...

  7. Electrokinetic high pressure hydraulic system

    DOE Patents [OSTI]

    Paul, Phillip H.; Rakestraw, David J.; Arnold, Don W.; Hencken, Kenneth R.; Schoeniger, Joseph S.; Neyer, David W.

    2003-06-03T23:59:59.000Z

    An electrokinetic high pressure hydraulic pump for manipulating fluids in capillary-based system. The pump uses electro-osmotic flow to provide a high pressure hydraulic system, having no moving mechanical parts, for pumping and/or compressing fluids, for providing valve means and means for opening and closing valves, for controlling fluid flow rate, and manipulating fluid flow generally and in capillary-based systems (microsystems), in particular. The compact nature of the inventive high pressure hydraulic pump provides the ability to construct a micro-scale or capillary-based HPLC system that fulfills the desire for small sample quantity, low solvent consumption, improved efficiency, the ability to run samples in parallel, and field portability. Control of pressure and solvent flow rate is achieved by controlling the voltage applied to an electrokinetic pump.

  8. Electrokinetic high pressure hydraulic system

    DOE Patents [OSTI]

    Paul, Phillip H. (Livermore, CA); Rakestraw, David J. (Fremont, CA); Arnold, Don W. (Livermore, CA); Hencken, Kenneth R. (Pleasanton, CA); Schoeniger, Joseph S. (Oakland, CA); Neyer, David W. (Castro Valley, CA)

    2001-01-01T23:59:59.000Z

    An electrokinetic high pressure hydraulic pump for manipulating fluids in capillary-based systems. The pump uses electro-osmotic flow to provide a high pressure hydraulic system, having no moving mechanical parts, for pumping and/or compressing fluids, for providing valve means and means for opening and closing valves, for controlling fluid flow rate, and manipulating fluid flow generally and in capillary-based systems (Microsystems), in particular. The compact nature of the inventive high pressure hydraulic pump provides the ability to construct a micro-scale or capillary-based HPLC system that fulfills the desire for small sample quantity, low solvent consumption, improved efficiency, the ability to run samples in parallel, and field portability. Control of pressure and solvent flow rate is achieved by controlling the voltage applied to an electrokinetic pump.

  9. High pressure ceramic joint

    DOE Patents [OSTI]

    Ward, Michael E. (Poway, CA); Harkins, Bruce D. (San Diego, CA)

    1993-01-01T23:59:59.000Z

    Many recuperators have components which react to corrosive gases and are used in applications where the donor fluid includes highly corrosive gases. These recuperators have suffered reduced life, increased service or maintenance, and resulted in increased cost. The present joint when used with recuperators increases the use of ceramic components which do not react to highly corrosive gases. Thus, the present joint used with the present recuperator increases the life, reduces the service and maintenance, and reduces the increased cost associated with corrosive action of components used to manufacture recuperators. The present joint is comprised of a first ceramic member, a second ceramic member, a mechanical locking device having a groove defined in one of the first ceramic member and the second ceramic member. The joint and the mechanical locking device is further comprised of a refractory material disposed in the groove and contacting the first ceramic member and the second ceramic member. The present joint mechanically provides a high strength load bearing joint having good thermal cycling characteristics, good resistance to a corrosive environment and good steady state strength at elevated temperatures.

  10. High pressure ceramic joint

    DOE Patents [OSTI]

    Ward, M.E.; Harkins, B.D.

    1993-11-30T23:59:59.000Z

    Many recuperators have components which react to corrosive gases and are used in applications where the donor fluid includes highly corrosive gases. These recuperators have suffered reduced life, increased service or maintenance, and resulted in increased cost. The present joint when used with recuperators increases the use of ceramic components which do not react to highly corrosive gases. Thus, the present joint used with the present recuperator increases the life, reduces the service and maintenance, and reduces the increased cost associated with corrosive action of components used to manufacture recuperators. The present joint is comprised of a first ceramic member, a second ceramic member, a mechanical locking device having a groove defined in one of the first ceramic member and the second ceramic member. The joint and the mechanical locking device is further comprised of a refractory material disposed in the groove and contacting the first ceramic member and the second ceramic member. The present joint mechanically provides a high strength load bearing joint having good thermal cycling characteristics, good resistance to a corrosive environment and good steady state strength at elevated temperatures. 4 figures.

  11. High Temperature, High Pressure Devices for Zonal Isolation in...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    High Temperature, High Pressure Devices for Zonal Isolation in Geothermal Wells High Temperature, High Pressure Devices for Zonal Isolation in Geothermal Wells High Temperature,...

  12. High pressure neon arc lamp

    DOE Patents [OSTI]

    Sze, Robert C.; Bigio, Irving J.

    2003-07-15T23:59:59.000Z

    A high pressure neon arc lamp and method of using the same for photodynamic therapies is provided. The high pressure neon arc lamp includes a housing that encloses a quantity of neon gas pressurized to about 500 Torr to about 22,000 Torr. At each end of the housing the lamp is connected by electrodes and wires to a pulse generator. The pulse generator generates an initial pulse voltage to breakdown the impedance of the neon gas. Then the pulse generator delivers a current through the neon gas to create an electrical arc that emits light having wavelengths from about 620 nanometers to about 645 nanometers. A method for activating a photosensitizer is provided. Initially, a photosensitizer is administered to a patient and allowed time to be absorbed into target cells. Then the high pressure neon arc lamp is used to illuminate the target cells with red light having wavelengths from about 620 nanometers to about 645 nanometers. The red light activates the photosensitizers to start a chain reaction that may involve oxygen free radicals to destroy the target cells. In this manner, a high pressure neon arc lamp that is inexpensive and efficiently generates red light useful in photodynamic therapy is provided.

  13. High pressure liquid level monitor

    DOE Patents [OSTI]

    Bean, Vern E. (Frederick, MD); Long, Frederick G. (Ijamsville, MD)

    1984-01-01T23:59:59.000Z

    A liquid level monitor for tracking the level of a coal slurry in a high-pressure vessel including a toroidal-shaped float with magnetically permeable bands thereon disposed within the vessel, two pairs of magnetic field generators and detectors disposed outside the vessel adjacent the top and bottom thereof and magnetically coupled to the magnetically permeable bands on the float, and signal processing circuitry for combining signals from the top and bottom detectors for generating a monotonically increasing analog control signal which is a function of liquid level. The control signal may be utilized to operate high-pressure control valves associated with processes in which the high-pressure vessel is used.

  14. Observations on vapor pressure in SPR caverns : sources.

    SciTech Connect (OSTI)

    Munson, Darrell Eugene

    2010-05-01T23:59:59.000Z

    The oil of the Strategic Petroleum Reserve (SPR) represents a national response to any potential emergency or intentional restriction of crude oil supply to this country, and conforms to International Agreements to maintain such a reserve. As assurance this reserve oil will be available in a timely manner should a restriction in supply occur, the oil of the reserve must meet certain transportation criteria. The transportation criteria require that the oil does not evolve dangerous gas, either explosive or toxic, while in the process of transport to, or storage at, the destination facility. This requirement can be a challenge because the stored oil can acquire dissolved gases while in the SPR. There have been a series of reports analyzing in exceptional detail the reasons for the increases, or regains, in gas content; however, there remains some uncertainty in these explanations and an inability to predict why the regains occur. Where the regains are prohibitive and exceed the criteria, the oil must undergo degasification, where excess portions of the volatile gas are removed. There are only two known sources of gas regain, one is the salt dome formation itself which may contain gas inclusions from which gas can be released during oil processing or storage, and the second is increases of the gases release by the volatile components of the crude oil itself during storage, especially if the stored oil undergoes heating or is subject to biological generation processes. In this work, the earlier analyses are reexamined and significant alterations in conclusions are proposed. The alterations are based on how the fluid exchanges of brine and oil uptake gas released from domal salt during solutioning, and thereafter, during further exchanges of fluids. Transparency of the brine/oil interface and the transfer of gas across this interface remains an important unanswered question. The contribution from creep induced damage releasing gas from the salt surrounding the cavern is considered through computations using the Multimechanism Deformation Coupled Fracture (MDCF) model, suggesting a relative minor, but potentially significant, contribution to the regain process. Apparently, gains in gas content can be generated from the oil itself during storage because the salt dome has been heated by the geothermal gradient of the earth. The heated domal salt transfers heat to the oil stored in the caverns and thereby increases the gas released by the volatile components and raises the boiling point pressure of the oil. The process is essentially a variation on the fractionation of oil, where each of the discrete components of the oil have a discrete temperature range over which that component can be volatized and removed from the remaining components. The most volatile components are methane and ethane, the shortest chain hydrocarbons. Since this fractionation is a fundamental aspect of oil behavior, the volatile component can be removed by degassing, potentially prohibiting the evolution of gas at or below the temperature of the degas process. While this process is well understood, the ability to describe the results of degassing and subsequent regain is not. Trends are not well defined for original gas content, regain, and prescribed effects of degassing. As a result, prediction of cavern response is difficult. As a consequence of this current analysis, it is suggested that solutioning brine of the final fluid exchange of a just completed cavern, immediately prior to the first oil filling, should be analyzed for gas content using existing analysis techniques. This would add important information and clarification to the regain process. It is also proposed that the quantity of volatile components, such as methane, be determined before and after any degasification operation.

  15. In-reactor oxidation of zircaloy-4 under low water vapor pressures

    SciTech Connect (OSTI)

    Walter G. Luscher; David J. Senor; Keven K. Clayton; Glen R. Longhurst

    2015-01-01T23:59:59.000Z

    Complementary in- and ex-reactor oxidation tests have been performed to evaluate the oxidation and hydrogen absorption performance of Zircaloy-4 (Zr-4) under relatively low partial pressures (300 and 1000 Pa) of water vapor at specified test temperatures (330 and 370 C). Data from these tests will be used to support the fabrication of components intended for isotope-producing targets and provide information regarding the temperature and pressure dependence of oxidation and hydrogen absorption of Zr- 4 over the specified range of test conditions. Comparisons between in- and ex-reactor test results were performed to evaluate the influence of irradiation.

  16. In-Reactor Oxidation of Zircaloy-4 Under Low Water Vapor Pressures

    SciTech Connect (OSTI)

    Luscher, Walter G.; Senor, David J.; Clayton, Kevin; Longhurst, Glen

    2015-01-01T23:59:59.000Z

    Complementary in- and ex-reactor oxidation tests have been performed to evaluate the oxidation and hydrogen absorption performance of Zircaloy-4 (Zr-4) under relatively low partial pressures (300 and 1000 Pa) of water vapor at specified test temperatures (330° and 370°C). Data from these tests will be used to support fabrication of components intended for isotope-producing targets and provide information regarding the temperature and pressure dependence of oxidation and hydrogen absorption of Zr-4 over the specified range of test conditions. Comparisons between in- and ex- reactor test results were performed to evaluate the influence of irradiation.

  17. High pressure xenon ionization detector

    DOE Patents [OSTI]

    Markey, John K. (New Haven, CT)

    1989-01-01T23:59:59.000Z

    A method is provided for detecting ionization comprising allowing particles that cause ionization to contact high pressure xenon maintained at or near its critical point and measuring the amount of ionization. An apparatus is provided for detecting ionization, the apparatus comprising a vessel containing a ionizable medium, the vessel having an inlet to allow high pressure ionizable medium to enter the vessel, a means to permit particles that cause ionization of the medium to enter the vessel, an anode, a cathode, a grid and a plurality of annular field shaping rings, the field shaping rings being electrically isolated from one another, the anode, cathode, grid and field shaping rings being electrically isolated from one another in order to form an electric field between the cathode and the anode, the electric field originating at the anode and terminating at the cathode, the grid being disposed between the cathode and the anode, the field shaping rings being disposed between the cathode and the grid, the improvement comprising the medium being xenon and the vessel being maintained at a pressure of 50 to 70 atmospheres and a temperature of 0.degree. to 30.degree. C.

  18. High average power magnetic modulator for metal vapor lasers

    DOE Patents [OSTI]

    Ball, Don G. (Livermore, CA); Birx, Daniel L. (Oakley, CA); Cook, Edward G. (Livermore, CA); Miller, John L. (Livermore, CA)

    1994-01-01T23:59:59.000Z

    A three-stage magnetic modulator utilizing magnetic pulse compression designed to provide a 60 kV pulse to a copper vapor laser at a 4.5 kHz repetition rate is disclosed. This modulator operates at 34 kW input power. The circuit includes a step up auto transformer and utilizes a rod and plate stack construction technique to achieve a high packing factor.

  19. Electokinetic high pressure hydraulic system

    DOE Patents [OSTI]

    Paul, Phillip H. (Livermore, CA); Rakestraw, David J. (Fremont, CA)

    2000-01-01T23:59:59.000Z

    A compact high pressure hydraulic system having no moving parts for converting electric potential to hydraulic force and for manipulating fluids. Electro-osmotic flow is used to provide a valve and means to compress a fluid or gas in a capillary-based system. By electro-osmotically moving an electrolyte between a first position opening communication between a fluid inlet and outlet and a second position closing communication between the fluid inlet and outlet the system can be configured as a valve. The system can also be used to generate forces as large as 2500 psi that can be used to compress a fluid, either a liquid or a gas.

  20. Solubility parameter and activity coefficient of HDEHP dimer in select organic diluents by vapor pressure osmometry

    SciTech Connect (OSTI)

    Gray, M.; Nilsson, M. [University of California Irvine, 916 Engineering Tower, UC Irvine, Irvine, CA 92697-2575 (United States); Zalupski, P. [Idaho National Laboratory, 2525 Fremont Avenue, Idaho Falls, ID 83415 (United States)

    2013-07-01T23:59:59.000Z

    A thorough understanding of the non-ideal behavior of the chemical components utilized in solvent extraction contributes to the success of any large-scale spent nuclear fuel treatment. To address this, our current work uses vapor pressure osmometry to characterize the non-ideal behavior of the solvent extraction agent di-(2-ethylhexyl) phosphoric acid (HDEHP), a common extractant in proposed separation schemes. Solubility parameters were fit to data on HDEHP at four temperatures using models based on Scatchard Hildebrand regular solution theory with Flory Huggins entropic corrections. The results are comparable but not identical to the activity coefficients from prior slope analysis in the literature. (authors)

  1. Vapor pressures and heats of vaporization of primary coal tars. Quarterly technical progress report, 1 July 1993--30 September 1993

    SciTech Connect (OSTI)

    Suuberg, E.M.; Oja, V.; Lilly, W.D.

    1993-12-31T23:59:59.000Z

    There is significant current interest in general area of coal pyrolysis, particularly with respect to comprehensive models of this complicated phenomenon. This interest derives from the central role of pyrolysis in all thermally driven coal conversion processes -- gasification, combustion, liquefaction, mild gasification, or thermal benefication. There remain several key data needs in these application areas. Among them is a need for more reliable correlation for prediction of vapor pressure of heavy, primary coal tars. Such information is important in design of all coal conversion processes, in which the volatility of tarry products is of major concern. Only very limited correlations exist, and these are not considered reliable to even an order of magnitude when applied to tars. The present project seeks to address this important gap in the near term by direct measurement of vapor pressures of coal tar fractions, by application of well-established techniques and modifications thereof. The principal objectives of the program are to: (1) obtain data on the vapor pressures and heats of vaporization of tars from a range of ranks of coal, (2) develop correlations based on a minimum set of conveniently measurable characteristics of the tars, (3) develop equipment that would allow performing such measurements in a reliable, straightforward fashion. Results of the literature survey are compiled. The experimental tasks have been concerned with setup and calibration.

  2. High-pressure microhydraulic actuator

    DOE Patents [OSTI]

    Mosier, Bruce P. (San Francisco, CA) [San Francisco, CA; Crocker, Robert W. (Fremont, CA) [Fremont, CA; Patel, Kamlesh D. (Dublin, CA) [Dublin, CA

    2008-06-10T23:59:59.000Z

    Electrokinetic ("EK") pumps convert electric to mechanical work when an electric field exerts a body force on ions in the Debye layer of a fluid in a packed bed, which then viscously drags the fluid. Porous silica and polymer monoliths (2.5-mm O.D., and 6-mm to 10-mm length) having a narrow pore size distribution have been developed that are capable of large pressure gradients (250-500 psi/mm) when large electric fields (1000-1500 V/cm) are applied. Flowrates up to 200 .mu.L/min and delivery pressures up to 1200 psi have been demonstrated. Forces up to 5 lb-force at 0.5 mm/s (12 mW) have been demonstrated with a battery-powered DC-DC converter. Hydraulic power of 17 mW (900 psi@ 180 uL/min) has been demonstrated with wall-powered high voltage supplies. The force and stroke delivered by an actuator utilizing an EK pump are shown to exceed the output of solenoids, stepper motors, and DC motors of similar size, despite the low thermodynamic efficiency.

  3. atmospheric-pressure chemical vapor: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    studied intensively and has overcome some of the constraints of traditional high-pressure high-temperature (HPHT) diamond synthesis methods (more) Chen, Yu-Chun 2009-01-01 12...

  4. Vapor pressure and boiling point elevation of slash pine black liquors: Predictive models with statistical approach

    SciTech Connect (OSTI)

    Zaman, A.A.; McNally, T.W.; Fricke, A.L. [Univ. of Florida, Gainesville, FL (United States)] [Univ. of Florida, Gainesville, FL (United States)

    1998-01-01T23:59:59.000Z

    Vapor-liquid equilibria and boiling point elevation of slash pine kraft black liquors over a wide range of solid concentrations (up to 85% solids) has been studied. The liquors are from a statistically designed pulping experiment for pulping slash pine in a pilot scale digester with four cooking variables of effective alkali, sulfidity, cooking time, and cooking temperature. It was found that boiling point elevation of black liquors is pressure dependent, and this dependency is more significant at higher solids concentrations. The boiling point elevation data at different solids contents (at a fixed pressure) were correlated to the dissolved solids (S/(1 {minus} S)) in black liquor. Due to the solubility limit of some of the salts in black liquor, a change in the slope of the boiling point elevation as a function of the dissolved solids was observed at a concentration of around 65% solids. An empirical method was developed to describe the boiling point elevation of each liquor as a function of pressure and solids mass fraction. The boiling point elevation of slash pine black liquors was correlated quantitatively to the pulping variables, using different statistical procedures. These predictive models can be applied to determine the boiling point rise (and boiling point) of slash pine black liquors at processing conditions from the knowledge of pulping variables. The results are presented, and their utility is discussed.

  5. NETL- High-Pressure Combustion Research Facility

    ScienceCinema (OSTI)

    None

    2014-06-26T23:59:59.000Z

    NETL's High-Pressure Combustion Facility is a unique resource within the National Laboratories system. It provides the test capabilities needed to evaluate new combustion concepts for high-pressure, high-temperature hydrogen and natural gas turbines. These concepts will be critical for the next generation of ultra clean, ultra efficient power systems.

  6. NETL- High-Pressure Combustion Research Facility

    SciTech Connect (OSTI)

    None

    2013-07-08T23:59:59.000Z

    NETL's High-Pressure Combustion Facility is a unique resource within the National Laboratories system. It provides the test capabilities needed to evaluate new combustion concepts for high-pressure, high-temperature hydrogen and natural gas turbines. These concepts will be critical for the next generation of ultra clean, ultra efficient power systems.

  7. Zirconate pyrochlores under high pressure. | EMSL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    phase transformation. Citation: Xiao HY, FX Zhang, F Gao, M Lang, RC Ewing, and WJ Weber.2010."Zirconate pyrochlores under high pressure."Physical Chemistry Chemical Physics....

  8. Soot particle aerosol dynamics at high pressure

    SciTech Connect (OSTI)

    Harris, S.J. (General Motors Research Labs., Warren, MI (USA). Physics Dept.); Kennedy, I.M. (California Univ., Davis, CA (USA). Dept. of Mechanical Engineering)

    1989-12-01T23:59:59.000Z

    The authors have used detailed calculations to analyze the coagulation dynamics of a soot aerosol at high pressures (20 and 50 atm). They find that the soot size distribution is altered compared to lower-pressure conditions because the mean free path at high pressures is reduced to the point that the particles are similar in size to the mean free path. At lower pressures the form of the size distribution becomes constant (self-preserving) in time, allowing optical measurements to be easily interpreted. However, the authors find that at pressures above about 5 atm the shape of the size distribution continually changes. As a result, proper and accurate interpretation of optical data at high pressures is more difficult than at lower pressures.

  9. High pressure low heat rate phosphoric acid fuel cell stack

    SciTech Connect (OSTI)

    Wertheim, R.J.

    1987-07-07T23:59:59.000Z

    A high pressure phosphoric acid fuel cell stack assembly is described comprising: (a) a stack of fuel cells for producing electricity, the stack including cathode means, anode means, and heat exchange means; (b) means for delivering pressurized air to the cathode means; (c) means for delivering a hydrogen rich fuel gas to the anode means for electrochemically reacting with oxygen in the pressurized air to produce electricity and water; (d) first conduit means connected to the cathode means for exhausting a mixture of oxygen-depleted air and reaction water from the cathode means; (e) second conduit means connected to the first conduit means for delivering a water fog to the first conduit means for entrainment in the mixture of oxygen-depleted air and reaction water to form a two phase coolant having a gaseous air phase and an entrained water droplet phase; (f) means for circulating the coolant to the heat exchange means to cool the stack solely through vaporization of the water droplet phase in the heat exchange means whereby a mixed gas exhaust of air and water vapor is exhausted from the heat exchange means; and (g) means for heating the mixed gas exhaust and delivering the heated mixed gas exhaust at reformer reaction temperatures to an autothermal reformer in the stack assembly for autothermal reaction with a raw fuel to form the hydrogen rich fuel.

  10. Portable high precision pressure transducer system

    DOE Patents [OSTI]

    Piper, T.C.; Morgan, J.P.; Marchant, N.J.; Bolton, S.M.

    1994-04-26T23:59:59.000Z

    A high precision pressure transducer system is described for checking the reliability of a second pressure transducer system used to monitor the level of a fluid confined in a holding tank. Since the response of the pressure transducer is temperature sensitive, it is continually housed in an battery powered oven which is configured to provide a temperature stable environment at specified temperature for an extended period of time. Further, a high precision temperature stabilized oscillator and counter are coupled to a single board computer to accurately determine the pressure transducer oscillation frequency and convert it to an applied pressure. All of the components are powered by the batteries which during periods of availability of line power are charged by an on board battery charger. The pressure readings outputs are transmitted to a line printer and a vacuum fluorescent display. 2 figures.

  11. Portable high precision pressure transducer system

    DOE Patents [OSTI]

    Piper, Thomas C. (Idaho Falls, ID); Morgan, John P. (Idaho Falls, ID); Marchant, Norman J. (Idaho Falls, ID); Bolton, Steven M. (Pocatello, ID)

    1994-01-01T23:59:59.000Z

    A high precision pressure transducer system for checking the reliability of a second pressure transducer system used to monitor the level of a fluid confined in a holding tank. Since the response of the pressure transducer is temperature sensitive, it is continually housed in an battery powered oven which is configured to provide a temperature stable environment at specified temperature for an extended period of time. Further, a high precision temperature stabilized oscillator and counter are coupled to a single board computer to accurately determine the pressure transducer oscillation frequency and convert it to an applied pressure. All of the components are powered by the batteries which during periods of availability of line power are charged by an on board battery charger. The pressure readings outputs are transmitted to a line printer and a vacuum florescent display.

  12. High-pressure studies of ammonia hydrates 

    E-Print Network [OSTI]

    Wilson, Craig W.

    2014-06-28T23:59:59.000Z

    Ammonia and water are major components of many planetary bodies, from comets and icy moons such as Saturn's Titan to the interiors of the planets Neptune and Uranus. Under a range of high pressures and/or low temperatures known ...

  13. High-pressure synthesis of electronic materials 

    E-Print Network [OSTI]

    Penny, George B. S.

    2010-01-01T23:59:59.000Z

    High-pressure techniques have become increasingly important in the synthesis of ceramic and metallic solids allowing the discovery of new materials with interesting properties. In this research dense solid oxides have ...

  14. High Pressure Hydrogen Tank Manufacturing

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(Fact Sheet), GeothermalGridHYDROGEN TOTechnologyHighLouisianaDepartment ofWorkshop

  15. On-line coating of glass with tin oxide by atmospheric pressure chemical vapor deposition.

    SciTech Connect (OSTI)

    Allendorf, Mark D.; Sopko, J.F. (PPF Industries, Pittsburgh, PA); Houf, William G.; Chae, Yong Kee; McDaniel, Anthony H.; Li, M. (PPF Industries, Pittsburgh, PA); McCamy, J.W. (PPF Industries, Pittsburgh, PA)

    2006-11-01T23:59:59.000Z

    Atmospheric pressure chemical vapor deposition (APCVD) of tin oxide is a very important manufacturing technique used in the production of low-emissivity glass. It is also the primary method used to provide wear-resistant coatings on glass containers. The complexity of these systems, which involve chemical reactions in both the gas phase and on the deposition surface, as well as complex fluid dynamics, makes process optimization and design of new coating reactors a very difficult task. In 2001 the U.S. Dept. of Energy Industrial Technologies Program Glass Industry of the Future Team funded a project to address the need for more accurate data concerning the tin oxide APCVD process. This report presents a case study of on-line APCVD using organometallic precursors, which are the primary reactants used in industrial coating processes. Research staff at Sandia National Laboratories in Livermore, CA, and the PPG Industries Glass Technology Center in Pittsburgh, PA collaborated to produce this work. In this report, we describe a detailed investigation of the factors controlling the growth of tin oxide films. The report begins with a discussion of the basic elements of the deposition chemistry, including gas-phase thermochemistry of tin species and mechanisms of chemical reactions involved in the decomposition of tin precursors. These results provide the basis for experimental investigations in which tin oxide growth rates were measured as a function of all major process variables. The experiments focused on growth from monobutyltintrichloride (MBTC) since this is one of the two primary precursors used industrially. There are almost no reliable growth-rate data available for this precursor. Robust models describing the growth rate as a function of these variables are derived from modeling of these data. Finally, the results are used to conduct computational fluid dynamic simulations of both pilot- and full-scale coating reactors. As a result, general conclusions are reached concerning the factors affecting the growth rate in on-line APCVD reactors. In addition, a substantial body of data was generated that can be used to model many different industrial tin oxide coating processes. These data include the most extensive compilation of thermochemistry for gas-phase tin-containing species as well as kinetic expressions describing tin oxide growth rates over a wide range of temperatures, pressures, and reactant concentrations.

  16. High pressure ceramic heat exchanger

    DOE Patents [OSTI]

    Harkins, B.D.; Ward, M.E.

    1998-09-22T23:59:59.000Z

    Many recuperators have components which react to corrosive gases and are used in applications where the donor fluid includes highly corrosive gases. These recuperators have suffered reduced life, increased service or maintenance, and resulted in increased cost. The present header assembly when used with recuperators reduces the brittle effect of a portion of the ceramic components. Thus, the present header assembly used with the present recuperator increases the life, reduces the service and maintenance, and reduces the increased cost associated with corrosive action of components used to manufacture recuperators. The present header assembly is comprised of a first ceramic member, a second ceramic member, a strengthening reinforcing member being in spaced relationship to the first ceramic member and the second ceramic member. The header assembly is further comprised of a refractory material disposed in contacting relationship with the first ceramic member, the second ceramic member and the strengthening reinforcing member. The present header assembly provides a high strength load bearing header assembly having good thermal cycling characteristics, good resistance to a corrosive environment and good steady state strength at elevated temperatures. 5 figs.

  17. High pressure ceramic heat exchanger

    DOE Patents [OSTI]

    Harkins, Bruce D. (San Diego, CA); Ward, Michael E. (Poway, CA)

    1998-01-01T23:59:59.000Z

    Many recuperators have components which react to corrosive gases and are used in applications where the donor fluid includes highly corrosive gases. These recuperators have suffered reduced life, increased service or maintenance, and resulted in increased cost. The present header assembly when used with recuperators reduces the brittle effect of a portion of the ceramic components. Thus, the present header assembly used with the present recuperator increases the life, reduces the service and maintenance, and reduces the increased cost associated with corrosive action of components used to manufacture recuperators. The present header assembly is comprised of a first ceramic member, a second ceramic member, a strengthening reinforcing member being in spaced relationship to the first ceramic member and the second ceramic member. The header assembly is further comprised of a refractory material disposed in contacting relationship with the first ceramic member, the second ceramic member and the strengthening reinforcing member. The present header assembly provides a high strength load bearing header assembly having good thermal cycling characteristics, good resistance to a corrosive environment and good steady state strength at elevated temperatures.

  18. High pressure ceramic heat exchanger

    DOE Patents [OSTI]

    Harkins, Bruce D. (San Diego, CA); Ward, Michael E. (Poway, CA)

    1999-01-01T23:59:59.000Z

    Many recuperators have components which react to corrosive gases and are used in applications where the donor fluid includes highly corrosive gases. These recuperators have suffered reduced life, increased service or maintenance, and resulted in increased cost. The present header assembly when used with recuperators reduces the brittle effect of a portion of the ceramic components. Thus, the present header assembly used with the present recuperator increases the life, reduces the service and maintenance, and reduces the increased cost associated with corrosive action of components used to manufacture recuperators. The present header assembly is comprised of a first ceramic member, a second ceramic member, a reinforcing member being in spaced relationship to the first ceramic member and the second ceramic member. The header assembly is further comprised of a refractory material disposed in contacting relationship with the first ceramic member, the second ceramic member and the reinforcing member and having a strengthening member wrapped around the refractory material. The present header assembly provides a high strength load bearing header assembly having good thermal cycling characteristics, good resistance to a corrosive environment and good steady state strength at elevated temperatures.

  19. Optimization of multi-pressure himidification-dehumidification desalination using thermal vapor compression and hybridization

    E-Print Network [OSTI]

    Mistry, Karan Hemant

    Humidification-dehumidification (HD or HDH) desalination, and specifically HD driven by a thermal vapor compressor (TVC), is a thermal desalination method that has the potential to produce potable water efficiently in order ...

  20. High pressure, high current, low inductance, high reliability sealed terminals

    DOE Patents [OSTI]

    Hsu, John S. (Oak Ridge, TN) [Oak Ridge, TN; McKeever, John W. (Oak Ridge, TN) [Oak Ridge, TN

    2010-03-23T23:59:59.000Z

    The invention is a terminal assembly having a casing with at least one delivery tapered-cone conductor and at least one return tapered-cone conductor routed there-through. The delivery and return tapered-cone conductors are electrically isolated from each other and positioned in the annuluses of ordered concentric cones at an off-normal angle. The tapered cone conductor service can be AC phase conductors and DC link conductors. The center core has at least one service conduit of gate signal leads, diagnostic signal wires, and refrigerant tubing routed there-through. A seal material is in direct contact with the casing inner surface, the tapered-cone conductors, and the service conduits thereby hermetically filling the interstitial space in the casing interior core and center core. The assembly provides simultaneous high-current, high-pressure, low-inductance, and high-reliability service.

  1. Automated High-Pressure Titration System with In Situ Infrared...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    High-Pressure Titration System with In Situ Infrared Spectroscopic Detection. Automated High-Pressure Titration System with In Situ Infrared Spectroscopic Detection. Abstract: A...

  2. A University Consortium on High Pressure, Lean Combustion for...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    High Pressure, Lean Combustion for Efficient and Clean IC Engines (UM - lead, MIT, UCB) A University Consortium on High Pressure, Lean Combustion for Efficient and Clean IC Engines...

  3. BILIWG Meeting: High Pressure Steam Reforming of Bio-Derived...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    High Pressure Steam Reforming of Bio-Derived Liquids (Presentation) BILIWG Meeting: High Pressure Steam Reforming of Bio-Derived Liquids (Presentation) Presented at the 2007...

  4. Consider Installing High-Pressure Boilers with BackpressureTurbine...

    Broader source: Energy.gov (indexed) [DOE]

    High-Pressure Boilers with Backpressure Turbine-Generators Consider Installing High-Pressure Boilers with Backpressure Turbine-Generators This tip sheet outlines the benefits of...

  5. advanced high pressure: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    interference with increased pressure. We Lee, Tonghun 87 Selection of High Strength Encapsulant for MEMS Devices Undergoing High Pressure Packaging CERN Preprints Summary:...

  6. High pressure water jet mining machine

    DOE Patents [OSTI]

    Barker, Clark R. (Rolla, MO)

    1981-05-05T23:59:59.000Z

    A high pressure water jet mining machine for the longwall mining of coal is described. The machine is generally in the shape of a plowshare and is advanced in the direction in which the coal is cut. The machine has mounted thereon a plurality of nozzle modules each containing a high pressure water jet nozzle disposed to oscillate in a particular plane. The nozzle modules are oriented to cut in vertical and horizontal planes on the leading edge of the machine and the coal so cut is cleaved off by the wedge-shaped body.

  7. HIGH PRESSURE COAL COMBUSTON KINETICS PROJECT

    SciTech Connect (OSTI)

    Stefano Orsino

    2005-03-30T23:59:59.000Z

    As part of the U.S. Department of Energy (DoE) initiative to improve the efficiency of coal-fired power plants and reduce the pollution generated by these facilities, DOE has funded the High-Pressure Coal Combustion Kinetics (HPCCK) Projects. A series of laboratory experiments were conducted on selected pulverized coals at elevated pressures with the specific goals to provide new data for pressurized coal combustion that will help extend to high pressure and validate models for burnout, pollutant formation, and generate samples of solid combustion products for analyses to fill crucial gaps in knowledge of char morphology and fly ash formation. Two series of high-pressure coal combustion experiments were performed using SRI's pressurized radiant coal flow reactor. The first series of tests characterized the near burner flame zone (NBFZ). Three coals were tested, two high volatile bituminous (Pittsburgh No.8 and Illinois No.6), and one sub-bituminous (Powder River Basin), at pressures of 1, 2, and 3 MPa (10, 20, and 30 atm). The second series of experiments, which covered high-pressure burnout (HPBO) conditions, utilized a range of substantially longer combustion residence times to produce char burnout levels from 50% to 100%. The same three coals were tested at 1, 2, and 3 MPa, as well as at 0.2 MPa. Tests were also conducted on Pittsburgh No.8 coal in CO2 entrainment gas at 0.2, 1, and 2 MPa to begin establishing a database of experiments relevant to carbon sequestration techniques. The HPBO test series included use of an impactor-type particle sampler to measure the particle size distribution of fly ash produced under complete burnout conditions. The collected data have been interpreted with the help of CFD and detailed kinetics simulation to extend and validate devolatilization, char combustion and pollutant model at elevated pressure. A global NOX production sub-model has been proposed. The submodel reproduces the performance of the detailed chemical reaction mechanism for the NBFZ tests.

  8. Advanced Diagnostics for High Pressure Spray Combustion.

    SciTech Connect (OSTI)

    Skeen, Scott A.; Manin, Julien Luc; Pickett, Lyle M.

    2014-06-01T23:59:59.000Z

    The development of accurate predictive engine simulations requires experimental data to both inform and validate the models, but very limited information is presently available about the chemical structure of high pressure spray flames under engine- relevant conditions. Probing such flames for chemical information using non- intrusive optical methods or intrusive sampling techniques, however, is challenging because of the physical and optical harshness of the environment. This work details two new diagnostics that have been developed and deployed to obtain quantitative species concentrations and soot volume fractions from a high-pressure combusting spray. A high-speed, high-pressure sampling system was developed to extract gaseous species (including soot precursor species) from within the flame for offline analysis by time-of-flight mass spectrometry. A high-speed multi-wavelength optical extinction diagnostic was also developed to quantify transient and quasi-steady soot processes. High-pressure sampling and offline characterization of gas-phase species formed following the pre-burn event was accomplished as well as characterization of gas-phase species present in the lift-off region of a high-pressure n-dodecane spray flame. For the initial samples discussed in this work several species were identified, including polycyclic aromatic hydrocarbons (PAH); however, quantitative mole fractions were not determined. Nevertheless, the diagnostic developed here does have this capability. Quantitative, time-resolved measurements of soot extinction were also accomplished and the novel use of multiple incident wavelengths proved valuable toward characterizing changes in soot optical properties within different regions of the spray flame.

  9. Dynamics of Low-Pressure and High-Pressure Fuel Cell Air Supply System1

    E-Print Network [OSTI]

    Peng, Huei

    comparing the low pressure system with the high- pressure system equipped with a high-speed compressor pressure of the FC that is defined as the pressure at which the reactant hydrogen and oxygen (air) are delivered to the FC stack flow fields. In the case of stored compressed hydrogen the pressure of the cathode

  10. varicose veins smoking obesity swine flu high blood pressure

    E-Print Network [OSTI]

    Diggle, Peter J.

    varicose veins smoking obesity swine flu high blood pressure parkinson's stress depression muscle stiffness heart attack asthma low blood pressure alzheimer's cancer diabetes kidney failure dementia smoking obesity swine flu high blood pressure parkinson's stress depression muscle stiffness heart attack

  11. Viscosities of natural gases at high pressures and high temperatures

    E-Print Network [OSTI]

    Viswanathan, Anup

    2007-09-17T23:59:59.000Z

    Estimation of viscosities of naturally occurring petroleum gases provides the information needed to accurately work out reservoir-engineering problems. Existing models for viscosity prediction are limited by data, especially at high pressures...

  12. Optical pumping and spectroscopy of Cs vapor at high magnetic field

    SciTech Connect (OSTI)

    Olsen, B. A.; Patton, B.; Jau, Y.-Y.; Happer, W. [Joseph Henry Laboratory, Department of Physics, Princeton University, Princeton, New Jersey 08544 (United States)

    2011-12-15T23:59:59.000Z

    We have measured changes in the ground-state populations of Cs vapor induced by optical pumping at high magnetic field. The 2.7-T field of our experiments is strong enough to decouple the nuclear and electronic spins, allowing us to independently measure each population. The spatial dependence of the Cs populations in small amounts of buffer gas obeys a simple coupled diffusion model and the relative populations reveal the details of relaxation within the vapor cell. Optical pumping can produce high nuclear polarization in the Cs vapor due to perturbations of the hyperfine interaction during collisions with buffer-gas particles and depending on the pumping transition, radiation trapping can strongly influence the electronic and nuclear polarizations in the vapor.

  13. Polymerization of Formic Acid under High Pressure

    SciTech Connect (OSTI)

    Goncharov, A F; Manaa, M R; Zaug, J M; Fried, L E; Montgomery, W B

    2004-08-23T23:59:59.000Z

    We report combined Raman, infrared (IR) and x-ray diffraction (XRD) measurements, along with ab initio calculations on formic acid under pressure up to 50 GPa. Contrary to the report of Allan and Clark (PRL 82, 3464 (1999)), we find an infinite chain low-temperature Pna2{sub 1} structure consisting of trans molecules to be a high-pressure phase at room temperature. Our data indicate the symmetrization and a partially covalent character of the intra-chain hydrogen bonds above approximately 20 GPa. Raman spectra and XRD patterns indicate a loss of the long-range order at pressures above 40 GPa with a large hysteresis at decompression. We attribute this behavior to a three-dimensional polymerization of formic acid.

  14. Z .Thin Solid Films 392 2001 231 235 Atmospheric pressure chemical vapor deposition of

    E-Print Network [OSTI]

    of electrochromic tungsten oxide films Roy G. Gordona,U , Sean Barryb , Jeffrey T. Bartona , Randy N.R. Broomhall oxide, WO , is a coloring layer commonly used in electrochromic windows and displays. Successful: Chemical vapor deposition; Tungsten; Oxides; Electrochromism 1. Introduction Tungsten oxide is a key

  15. Engine having a high pressure hydraulic system and low pressure lubricating system

    DOE Patents [OSTI]

    Bartley, Bradley E. (Manito, IL); Blass, James R. (Bloomington, IL); Gibson, Dennis H. (Chillicothe, IL)

    2000-01-01T23:59:59.000Z

    An engine includes a high pressure hydraulic system having a high pressure pump and at least one hydraulically-actuated device attached to an engine housing. A low pressure engine lubricating system is attached to the engine housing and includes a circulation conduit fluidly connected to an outlet from the high pressure pump.

  16. High strain rate metalworking with vaporizing foil actuator: Control of flyer velocity by varying input energy and foil thickness

    SciTech Connect (OSTI)

    Vivek, A., E-mail: vivek.4@osu.edu; Hansen, S. R.; Daehn, Glenn S. [Department of Materials Science and Engineering, The Ohio State University, 2041, College Road, Columbus, Ohio 43210 (United States)

    2014-07-15T23:59:59.000Z

    Electrically driven rapid vaporization of thin metallic foils can generate a high pressure which can be used to launch flyers at high velocities. Recently, vaporizing foil actuators have been applied toward a variety of impulse-based metal working operations. In order to exercise control over this useful tool, it is imperative that an understanding of the effect of characteristics of the foil actuator on its ability for mechanical impulse generation is developed. Here, foil actuators made out of 0.0508 mm, 0.0762 mm, and 0.127 mm thick AA1145 were used for launching AA2024-T3 sheets of thickness 0.508 mm toward a photonic Doppler velocimeter probe. Launch velocities ranging between 300 m/s and 1100 m/s were observed. In situ measurement of velocity, current, and voltage assisted in understanding the effect of burst current density and deposited electrical energy on average pressure and velocity with foil actuators of various thicknesses. For the pulse generator, geometry, and flyer used here, the 0.0762 mm thick foil was found to be optimal for launching flyers to high velocities over short distances. Experimenting with annealed foil actuators resulted in no change in the temporal evolution of flyer velocity as compared to foil actuators of full hard temper. A physics-based analytical model was developed and found to have reasonable agreement with experiment.

  17. High-pressure liquid chromatographic gradient mixer

    DOE Patents [OSTI]

    Daughton, C.G.; Sakaji, R.H.

    1982-09-08T23:59:59.000Z

    A gradient mixer effects the continuous mixing of any two miscible solvents without excessive decay or dispersion of the resultant isocratic effluent or of a linear or exponential gradient. The two solvents are fed under low or high pressure by means of two high performance liquid chromatographic pumps. The mixer comprises a series of ultra-low dead volume stainless steel tubes and low dead volume chambers. The two solvent streams impinge head-on at high fluxes. This initial nonhomogeneous mixture is then passed through a chamber packed with spirally-wound wires which cause turbulent mixing thereby homogenizing the mixture with minimum band-broadening.

  18. High pressure liquid chromatographic gradient mixer

    DOE Patents [OSTI]

    Daughton, Christian G. (San Pablo, CA); Sakaji, Richard H. (El Cerrito, CA)

    1985-01-01T23:59:59.000Z

    A gradient mixer which effects the continuous mixing of any two miscible solvents without excessive decay or dispersion of the resultant isocratic effluent or of a linear or exponential gradient. The two solvents are fed under low or high pressure by means of two high performance liquid chromatographic pumps. The mixer comprises a series of ultra-low dead volume stainless steel tubes and low dead volume chambers. The two solvent streams impinge head-on at high fluxes. This initial nonhomogeneous mixture is then passed through a chamber packed with spirally-wound wires which cause turbulent mixing thereby homogenizing the mixture with minimum "band-broadening".

  19. Characterization and fate of vapor-phase organic constituents from atmospheric pressure fluidized bed combustors (AFBC): East Stroudsburg University AFBC

    SciTech Connect (OSTI)

    Yeh, Hsu-Chi; Newton, G.J.; Henderson, T.R.; Hobbs, C.H.

    1987-08-01T23:59:59.000Z

    Very little research has been devoted to the characterization of vapor-phase organic compounds in gaseous streams. Because of the concerns that gaseous organic compounds from FBCs may include potentially toxic and/or mutagenic materials. We will measure vapor-phase hydrocarbon concentrations in the process streams of operating FBCs. This report describes our field sampling results on the atmospheric pressure fluidized bed combustor (AFBC) at the East Stroudsburg University during its normal operation for supplying heat and hot water to the campus. This AFBC has a bed size of 36 ft/sup 2/ and was burning anthracite culm. The culm consumption rates during the week of our sampling period were 1600 to 3000 lb/hr. Emphasis was placed on characterization of process stream effluents, including particles and vapor-phase organic constituents. Results indicated that the mass concentration (or loading) of particulate matter within the effluent stream was similar to other FBCs that have been studied. The particulate mass concentration measured after the baghouse location was 0.0048 g/m/sup 3/ (0.0047 lb/10/sup 6/ Btu). This was equivalent to a total of 35 g/hr of particulate emissions. The fraction of particulate material presented as organics (extractable fraction) was, on the average, less than 2% of total mass of particulate emissions. The vapor-phase organic contents indicated that the quantities of individual polycyclic aromatic hydrocarbons (PAHs) were low, being less than 2.5 ..mu..g/m/sup 3/ for any individual sample. Most of the PAHs detected were low boiling compounds such as naphthalene or phenanthrene, with trace amounts of pyrene. 22 refs., 13 figs., 11 tabs.

  20. Pb nanowire formation on Al/lead zirconate titanate surfaces in high-pressure hydrogen

    SciTech Connect (OSTI)

    Alvine, Kyle J.; Shutthanandan, V.; Arey, Bruce W.; Wang, Chong M.; Bennett, Wendy D.; Pitman, Stan G.

    2012-07-12T23:59:59.000Z

    Thin films of Al on lead zirconate titanate (PZT) annealed in high-pressure hydrogen at 100C exhibit surface Pb nanowire growth. Wire diameter is approximately 80 nm and length can exceed 100 microns. Based on microstructural analysis using electron microscopy and ion scattering, a vapor-solid scheme with hydrogen as a carrier gas was proposed as a growth mechanism. We expect that these observations may lead to controlled Pb nanowires growth through pattering of the Al film.

  1. Advanced High-Temperature, High-Pressure Transport Reactor Gasification

    SciTech Connect (OSTI)

    Michael L. Swanson

    2005-08-30T23:59:59.000Z

    The transport reactor development unit (TRDU) was modified to accommodate oxygen-blown operation in support of a Vision 21-type energy plex that could produce power, chemicals, and fuel. These modifications consisted of changing the loop seal design from a J-leg to an L-valve configuration, thereby increasing the mixing zone length and residence time. In addition, the standpipe, dipleg, and L-valve diameters were increased to reduce slugging caused by bubble formation in the lightly fluidized sections of the solid return legs. A seal pot was added to the bottom of the dipleg so that the level of solids in the standpipe could be operated independently of the dipleg return leg. A separate coal feed nozzle was added that could inject the coal upward into the outlet of the mixing zone, thereby precluding any chance of the fresh coal feed back-mixing into the oxidizing zone of the mixing zone; however, difficulties with this coal feed configuration led to a switch back to the original downward configuration. Instrumentation to measure and control the flow of oxygen and steam to the burner and mix zone ports was added to allow the TRDU to be operated under full oxygen-blown conditions. In total, ten test campaigns have been conducted under enriched-air or full oxygen-blown conditions. During these tests, 1515 hours of coal feed with 660 hours of air-blown gasification and 720 hours of enriched-air or oxygen-blown coal gasification were completed under this particular contract. During these tests, approximately 366 hours of operation with Wyodak, 123 hours with Navajo sub-bituminous coal, 143 hours with Illinois No. 6, 106 hours with SUFCo, 110 hours with Prater Creek, 48 hours with Calumet, and 134 hours with a Pittsburgh No. 8 bituminous coal were completed. In addition, 331 hours of operation on low-rank coals such as North Dakota lignite, Australian brown coal, and a 90:10 wt% mixture of lignite and wood waste were completed. Also included in these test campaigns was 50 hours of gasification on a petroleum coke from the Hunt Oil Refinery and an additional 73 hours of operation on a high-ash coal from India. Data from these tests indicate that while acceptable fuel gas heating value was achieved with these fuels, the transport gasifier performs better on the lower-rank feedstocks because of their higher char reactivity. Comparable carbon conversions have been achieved at similar oxygen/coal ratios for both air-blown and oxygen-blown operation for each fuel; however, carbon conversion was lower for the less reactive feedstocks. While separation of fines from the feed coals is not needed with this technology, some testing has suggested that feedstocks with higher levels of fines have resulted in reduced carbon conversion, presumably due to the inability of the finer carbon particles to be captured by the cyclones. These data show that these low-rank feedstocks provided similar fuel gas heating values; however, even among the high-reactivity low-rank coals, the carbon conversion did appear to be lower for the fuels (brown coal in particular) that contained a significant amount of fines. The fuel gas under oxygen-blown operation has been higher in hydrogen and carbon dioxide concentration since the higher steam injection rate promotes the water-gas shift reaction to produce more CO{sub 2} and H{sub 2} at the expense of the CO and water vapor. However, the high water and CO{sub 2} partial pressures have also significantly reduced the reaction of (Abstract truncated)

  2. Use Vapor Recompression to Recover Low-Pressure Waste Steam (Revised0

    SciTech Connect (OSTI)

    Not Available

    2008-03-01T23:59:59.000Z

    This revised ITP tip sheet on recovering low-pressure waste steam provides how-to advice for improving industrial steam systems using low-cost, proven practices and technologies.

  3. High pressure-resistant nonincendive emulsion explosive

    DOE Patents [OSTI]

    Ruhe, Thomas C. (Duquesne, PA); Rao, Pilaka P. (Baghlingampalli, IN)

    1994-01-01T23:59:59.000Z

    An improved emulsion explosive composition including hollow microspheres/bulking agents having high density and high strength. The hollow microspheres/bulking agents have true particle densities of about 0.2 grams per cubic centimeter or greater and include glass, siliceous, ceramic and synthetic resin microspheres, expanded minerals, and mixtures thereof. The preferred weight percentage of hollow microspheres/bulking agents in the composition ranges from 3.0 to 10.0 A chlorinated paraffin oil, also present in the improved emulsion explosive composition, imparts a higher film strength to the oil phase in the emulsion. The emulsion is rendered nonincendive by the production of sodium chloride in situ via the decomposition of sodium nitrate, a chlorinated paraffin oil, and sodium perchlorate. The air-gap sensitivity is improved by the in situ formation of monomethylamine perchlorate from dissolved monomethylamine nitrate and sodium perchlorate. The emulsion explosive composition can withstand static pressures to 139 bars and dynamic pressure loads on the order of 567 bars.

  4. High-pressure coal fuel processor development

    SciTech Connect (OSTI)

    Greenhalgh, M.L. (Caterpillar, Inc., Peoria, IL (United States))

    1992-12-01T23:59:59.000Z

    Caterpillar shares DOE/METC interest in demonstrating the technology required to displace petroleum-based engine fuels with various forms of low cost coal. Current DOE/METC programs on mild gasification and coal-water-slurries are addressing two approaches to this end. Engine and fuel processor system concept studies by Caterpillar have identified a third, potentially promising, option. This option includes high-pressure fuel processing of run-of-the-mine coal and direct injection of the resulting low-Btu gas stream into an ignition assisted, high compression ratio diesel engine. The compactness and predicted efficiency of the system make it suitable for application to line-haul railroad locomotives. Two overall conclusions resulted from Task 1. First direct injected, ignition assisted Diesel cycle engine combustion systems can be suitably modified to efficiently utilize low-Btu gas fuels. Second, high pressure gasification of selected run-of-the-mine coals in batch-loaded fuel processors is feasible. These two findings, taken together, significantly reduce the perceived technical risk associated with the further development of the proposed coal gas fueled Diesel cycle power plant concept. The significant conclusions from Task 2 were: An engine concept, derived from a Caterpillar 3600 series engine, and a fuel processor concept, based on scaling up a removable-canister configuration from the test rig, appear feasible; and although the results of this concept study are encouraging, further, full-scale component research and development are required before attempting a full-scale integrated system demonstration effort.

  5. LNG Vehicle High-Pressure Fuel System and ''Cold Energy'' Utilization

    SciTech Connect (OSTI)

    powers,Charles A.; Derbidge, T. Craig

    2001-03-27T23:59:59.000Z

    A high-pressure fuel system for LNG vehicles with direct-injection natural gas engines has been developed and demonstrated on a heavy-duty truck. A new concept for utilizing the ''cold energy'' associated with LNG vehicles to generate mechanical power to drive auxiliary equipment (such as high-pressure fuel pumps) has also been developed and demonstrated in the laboratory. The high-pressure LNG fuel system development included the design and testing of a new type of cryogenic pump utilizes multiple chambers and other features to condense moderate quantities of sucked vapor and discharge supercritical LNG at 3,000 to 4,000 psi. The pump was demonstrated on a Class 8 truck with a Westport high-pressure direct-injection Cummins ISX engine. A concept that utilizes LNG's ''cold energy'' to drive a high-pressure fuel pump without engine attachments or power consumption was developed. Ethylene is boiled and superheated by the engine coolant, and it is cooled and condensed by rejecting h eat to the LNG. Power is extracted in a full-admission blowdown process, and part of this power is applied to pump the ethylene liquid to the boiler pressure. Tests demonstrated a net power output of 1.1. hp at 1.9 Lbm/min of LNG flow, which is adequate to isentropically pump the LNG to approximately 3,400 psi..

  6. Thermal expansion of low-pressure chemical vapor deposition polysilicon films

    E-Print Network [OSTI]

    Ballarini, Roberto

    polysilicon films were deposited on the sub- strates by LPCVD in a hot-walled horizontal tube fur- nace with an inner diameter of 225 mm, using SiH4 at a flow rate of 100 sccm and a pressure of 300 mtorr J. Mater

  7. High-expansion foam for LNG vapor mitigation. Topical report, September 1987-December 1989

    SciTech Connect (OSTI)

    Atallah, S.; Shah, J.N.; Peterlinz, M.E.

    1990-05-01T23:59:59.000Z

    One of the purposes of these high expansion foam systems is to reduce the extent of the hazardous vapor cloud generated during an accidental LNG release. Should the LNG ignite, these systems serve the additional function of controlling the LNG fire and minimizing its radiation to the surroundings. Foam generators have been installed along the tops of dike walls surrounding some LNG storage tanks, and around other fenced containment areas where LNG may be accidentally released, such as LNG pump pits and pipe rack trenches. To date there are no technically justifiable guidelines for the design and installation of these systems. Furthermore, there are no models that may be used describe the vapor source so as to be able to predict the reduction in the hazardous vapor cloud zone when high expansion foam is applied to an LNG spill. Information is essential not only for the optimal design of high expansion foam systems, but also for comparing the cost effectiveness of alternative LNG vapor mitigation measures.

  8. accessing high pressure: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    place, rem... Liva, Gianluigi; Chiani, Marco 2010-01-01 102 Selection of High Strength Encapsulant for MEMS Devices Undergoing High Pressure Packaging CERN Preprints Summary:...

  9. Fundamentals of High Pressure Combustion Chapter in High Pressure Processes in Chemical Engineering, Edited by Maximillian Lackner,

    E-Print Network [OSTI]

    Miller, Richard S.

    [2]. Furthermore, gas turbine combustion pres- sures have been increasing at a near linear rateFundamentals of High Pressure Combustion Chapter in High Pressure Processes in Chemical Engineering of the following chapter is to present an overview of the fundamentals of combustion processes in high pressure

  10. Effect of high pressure on structural oddities 

    E-Print Network [OSTI]

    Johnstone, Russell D. L.

    2010-01-01T23:59:59.000Z

    This thesis describes the effect of pressure on crystal structures that are in some way unusual. The aim was to investigate whether pressure could be used to force these ‘structural oddities’ to conform to more conventional ...

  11. Condensed matter at high shock pressures

    SciTech Connect (OSTI)

    Nellis, W.J.; Holmes, N.C.; Mitchell, A.C.; Radousky, H.B.; Hamilton, D.

    1985-07-12T23:59:59.000Z

    Experimental techniques are described for shock waves in liquids: Hugoniot equation-of-state, shock temperature and emission spectroscopy, electrical conductivity, and Raman spectroscopy. Experimental data are reviewed and presented in terms of phenomena that occur at high densities and temperatures in shocked He, Ar, N/sub 2/, CO, SiO/sub 2/-aerogel, H/sub 2/O, and C/sub 6/H/sub 6/. The superconducting properties of Nb metal shocked to 100 GPa (1 Mbar) and recovered intact are discussed in terms of prospects for synthesizing novel, metastable materials. Ultrahigh pressure data for Cu is reviewed in the range 0.3 to 6TPa (3 to 60 Mbar). 56 refs., 9 figs., 1 tab.

  12. Low energy high pressure miniature screw valve

    DOE Patents [OSTI]

    Fischer, Gary J. (Sandia Park, NM); Spletzer, Barry L. (Albuquerque, NM)

    2006-12-12T23:59:59.000Z

    A low energy high pressure screw valve having a valve body having an upper portion and a lower portion, said lower portion of said valve body defining an inlet flow passage and an outlet flow passage traversing said valve body to a valve seat, said upper portion of said valve body defining a cavity at said valve seat, a diaphragm restricting flow between said upper portion of said valve body and said lower portion, said diaphragm capable of engaging said valve seat to restrict fluid communication between said inlet passage and said outlet passage, a plunger within said cavity supporting said diaphragm, said plunger being capable of engaging said diaphragm with said valve seat at said inlet and outlet fluid passages, said plunger being in point contact with a drive screw having threads engaged with opposing threads within said upper portion of said valve body such engagement allowing motion of said drive screw within said valve body.

  13. High pressure fiber optic sensor system

    SciTech Connect (OSTI)

    Guida, Renato; Xia, Hua; Lee, Boon K; Dekate, Sachin N

    2013-11-26T23:59:59.000Z

    The present application provides a fiber optic sensor system. The fiber optic sensor system may include a small diameter bellows, a large diameter bellows, and a fiber optic pressure sensor attached to the small diameter bellows. Contraction of the large diameter bellows under an applied pressure may cause the small diameter bellows to expand such that the fiber optic pressure sensor may measure the applied pressure.

  14. FORMATION OF COSMIC CRYSTALS IN HIGHLY SUPERSATURATED SILICATE VAPOR PRODUCED BY PLANETESIMAL BOW SHOCKS

    SciTech Connect (OSTI)

    Miura, H.; Yamada, J.; Tsukamoto, K.; Nozawa, J. [Department of Earth Sciences, Tohoku University, Aoba 6-3, Aramaki, Aoba-ku, Sendai 980-8578 (Japan); Tanaka, K. K.; Yamamoto, T. [Institute of Low Temperature Science, Hokkaido University, Sapporo 060-0819 (Japan); Nakamoto, T., E-mail: miurah@m.tohoku.ac.j [Earth and Planetary Sciences, Tokyo Institute of Technology, Meguro, Tokyo 152-8551 (Japan)

    2010-08-10T23:59:59.000Z

    Several lines of evidence suggest that fine silicate crystals observed in primitive meteorite and interplanetary dust particles (IDPs) nucleated in a supersaturated silicate vapor followed by crystalline growth. We investigated evaporation of {mu}m-sized silicate particles heated by a bow shock produced by a planetesimal orbiting in the gas in the early solar nebula and condensation of crystalline silicate from the vapor thus produced. Our numerical simulation of shock-wave heating showed that these {mu}m-sized particles evaporate almost completely when the bow shock is strong enough to cause melting of chondrule precursor dust particles. We found that the silicate vapor cools very rapidly with expansion into the ambient unshocked nebular region; for instance, the cooling rate is estimated to be as high as 2000 K s{sup -1} for a vapor heated by a bow shock associated with a planetesimal of radius 1 km. The rapid cooling of the vapor leads to nonequilibrium gas-phase condensation of dust at temperatures much lower than those expected from the equilibrium condensation. It was found that the condensation temperatures are lower by a few hundred K or more than the equilibrium temperatures. This explains the results of the recent experimental studies of condensation from a silicate vapor that condensation in such large supercooling reproduces morphologies similar to those of silicate crystals found in meteorites. Our results strongly suggest that the planetesimal bow shock is one of the plausible sites for formation of not only chondrules but also other cosmic crystals in the early solar system.

  15. Organic vapor jet printing system

    DOE Patents [OSTI]

    Forrest, Stephen R

    2012-10-23T23:59:59.000Z

    An organic vapor jet printing system includes a pump for increasing the pressure of an organic flux.

  16. Competition between vitrification and crystallization of methanol at high pressure

    E-Print Network [OSTI]

    Vos, Willem L.

    Competition between vitrification and crystallization of methanol at high pressure Marco J. P methanol at high pressure up to 33 GPa at room temperature with x-ray diffraction, optical polarization and vitrification is observed when methanol is superpressed beyond the freezing pressure of 3.5 GPa: between 5

  17. Structure of crystalline methanol at high pressure David R. Allan

    E-Print Network [OSTI]

    Vos, Willem L.

    Structure of crystalline methanol at high pressure David R. Allan Department of Physics structure, including all atomic positions, of methanol at high pressure and room temperature pressure of methanol is 3.5 GPa. In practice however, it is very easy to superpress the liquid phase

  18. Automated high pressure cell for pressure jump x-ray diffraction

    SciTech Connect (OSTI)

    Brooks, Nicholas J.; Gauthe, Beatrice L. L. E.; Templer, Richard H.; Ces, Oscar; Seddon, John M. [Department of Chemistry, Imperial College London, South Kensington Campus, London SW7 2AZ (United Kingdom); Terrill, Nick J. [Diamond Light Source, Harwell Science and Innovation Campus, Didcot, Oxfordshire OX11 0DE (United Kingdom); Rogers, Sarah E. [ISIS, Rutherford Appleton Laboratory, Harwell Science and Innovation Campus, Didcot, Oxfordshire OX11 0QX (United Kingdom)

    2010-06-15T23:59:59.000Z

    A high pressure cell for small and wide-angle x-ray diffraction measurements of soft condensed matter samples has been developed, incorporating a fully automated pressure generating network. The system allows both static and pressure jump measurements in the range of 0.1-500 MPa. Pressure jumps can be performed as quickly as 5 ms, both with increasing and decreasing pressures. Pressure is generated by a motorized high pressure pump, and the system is controlled remotely via a graphical user interface to allow operation by a broad user base, many of whom may have little previous experience of high pressure technology. Samples are loaded through a dedicated port allowing the x-ray windows to remain in place throughout an experiment; this facilitates accurate subtraction of background scattering. The system has been designed specifically for use at beamline I22 at the Diamond Light Source, United Kingdom, and has been fully integrated with the I22 beamline control systems.

  19. Calibrated vapor generator source

    DOE Patents [OSTI]

    Davies, J.P.; Larson, R.A.; Goodrich, L.D.; Hall, H.J.; Stoddard, B.D.; Davis, S.G.; Kaser, T.G.; Conrad, F.J.

    1995-09-26T23:59:59.000Z

    A portable vapor generator is disclosed that can provide a controlled source of chemical vapors, such as, narcotic or explosive vapors. This source can be used to test and calibrate various types of vapor detection systems by providing a known amount of vapors to the system. The vapor generator is calibrated using a reference ion mobility spectrometer. A method of providing this vapor is described, as follows: explosive or narcotic is deposited on quartz wool, placed in a chamber that can be heated or cooled (depending on the vapor pressure of the material) to control the concentration of vapors in the reservoir. A controlled flow of air is pulsed over the quartz wool releasing a preset quantity of vapors at the outlet. 10 figs.

  20. Calibrated vapor generator source

    DOE Patents [OSTI]

    Davies, John P. (Idaho Falls, ID); Larson, Ronald A. (Idaho Falls, ID); Goodrich, Lorenzo D. (Shelley, ID); Hall, Harold J. (Idaho Falls, ID); Stoddard, Billy D. (Idaho Falls, ID); Davis, Sean G. (Idaho Falls, ID); Kaser, Timothy G. (Idaho Falls, ID); Conrad, Frank J. (Albuquerque, NM)

    1995-01-01T23:59:59.000Z

    A portable vapor generator is disclosed that can provide a controlled source of chemical vapors, such as, narcotic or explosive vapors. This source can be used to test and calibrate various types of vapor detection systems by providing a known amount of vapors to the system. The vapor generator is calibrated using a reference ion mobility spectrometer. A method of providing this vapor is described, as follows: explosive or narcotic is deposited on quartz wool, placed in a chamber that can be heated or cooled (depending on the vapor pressure of the material) to control the concentration of vapors in the reservoir. A controlled flow of air is pulsed over the quartz wool releasing a preset quantity of vapors at the outlet.

  1. Use Vapor Recompression to Recover Low-Pressure Waste Steam | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: SinceDevelopment | Department of Energy $18UnrevisedCool Roof InfrastructureLow-Pressure

  2. Particulate removal from high-temperature, high-pressure combustion gases

    SciTech Connect (OSTI)

    Henry, R.F.; Saxena, S.C.; Podolski, W.F.

    1983-10-01T23:59:59.000Z

    The adoption by utilities of coal-fired pressurized fluidized-bed/combined cycle combustion systems for electric power generation depends to a large extent on the development of an efficient and economic cleanup system for the high-temperature, high-pressure combustion gases. For adequate turbine protection, these gases must be sufficiently cleaned to bring particulate erosion and alkali vapor corrosion to a level acceptable to gas turbine manufacturers. At the same time, the total particulate content of the flue gas must be reduced to the limit set by the Environmental Protection Agency. To accomplish particulate removal from a dust-laden gas stream, a number of separation devices have been developed. These include conventional and augmented cyclones; porous metal, fiber, fabric, and ceramic filters, as well as fixed, moving, and fluidized-bed granular filters; and electrostatic precipitators. Several other novel separation devices have been proposed and developed to different degrees such as: contactors using molten salt, metal, or glass, dry scrubbers, acoustic agglomerators, as well as cyclones and granular-bed filters with external electrostatic or magnetic fields. Some of these separation devices in various combinations have been tested in process development units or in hot gas simulators by ANL, CPC, CURL, C-W, Exxon, GE, Westinghouse, etc. The results are discussed and evaluated for PFBC applications.

  3. Growth of Large-Area Aligned Molybdenum Nanowires by High Temperature Chemical Vapor Deposition: Synthesis, Growth Mechanism, and Device Application

    E-Print Network [OSTI]

    Wang, Zhong L.

    , thermogravimetry, and differential scanning calorimetry analysis, as well as structure analysis by electron on the decomposition of MoO2 vapors through condensation of its vapor at high substrate temperatures. The aligned nanowires with H2 gas.6d-f However, the reduction process degrades the crystal- linity of the nanowires

  4. Elasticity of Materials at High Pressure

    E-Print Network [OSTI]

    Gleason, Arianna Elizabeth

    2010-01-01T23:59:59.000Z

    implications for lower mantle mineralogy, Earth Planet. Sci.C.R. (1998), Lower mantle mineralogy and the geophysical,in Ultrahigh-Pressure Mineralogy: Physics and Chemistry of

  5. Evidence of Tetragonal Nanodomains in the high pressure polymorph

    SciTech Connect (OSTI)

    Ehm, L.; Borkowski, L.A.; Parise J.B.; Ghose, S.; Chen, Z.

    2010-12-17T23:59:59.000Z

    The pressure induced P4mm {yields} Pm{bar 3}m phase transition in BaTiO{sub 3} perovskite was investigated by x-ray total scattering. The evolution of the structure was analyzed by fitting pair distribution functions over a pressure range from ambient pressure up to 6.85(7) GPa. Evidence for the existence of tetragonal ferroelectric nanodomains at high pressure was found. The average size of the nanodomains in the high-pressure phase decreases with increasing pressure. Extrapolation of the domain size to pressures higher than studied experimentally suggests a disappearance of the ferroelectric domains at about 9.3(5) GPa and a cubic symmetry of BaTiO{sub 3} high-pressure phase.

  6. Single stage high pressure centrifugal slurry pump

    DOE Patents [OSTI]

    Meyer, John W. (Palo Alto, CA); Bonin, John H. (Sunnyvale, CA); Daniel, Arnold D. (Alameda, CA)

    1984-03-27T23:59:59.000Z

    Apparatus is shown for feeding a slurry to a pressurized housing. An impeller that includes radial passages is mounted in the loose fitting housing. The impeller hub is connected to a drive means and a slurry supply means which extends through the housing. Pressured gas is fed into the housing for substantially enveloping the impeller in a bubble of gas.

  7. Industrial Heat Pumps Using Solid/Vapor Working Fluids

    E-Print Network [OSTI]

    Rockenfeller, U.

    with vapor re-compression recovery systems. The state-of-the-art heat pump equipment employing liquid/vapor working fluids fulfills the requirements only in some applications. The employment of solid/vapor complex compounds leads to 'nore cost effective... allows for firing temperatures much higher than possible with liquid/vapor systems. The high energy density per unit mass and the independence of the vapor pressure from the refrigerant concentration (p = f (T), p "# f( x)) over a wide range leads...

  8. HIGH TEMPERATURE HIGH PRESSURE THERMODYNAMIC MEASUREMENTS FOR COAL MODEL COMPOUNDS

    SciTech Connect (OSTI)

    Vinayak N. Kabadi

    1999-02-20T23:59:59.000Z

    It is well known that the fluid phase equilibria can be represented by a number of {gamma}-models , but unfortunately most of them do not function well under high temperature. In this calculation, we mainly investigate the performance of UNIQUAC and NRTL models under high temperature, using temperature dependent parameters rather than using the original formulas. the other feature of this calculation is that we try to relate the excess Gibbs energy G{sup E}and enthalpy of mixing H{sup E}simultaneously. In other words, we will use the high temperature and pressure G{sup E} and H{sup E}data to regress the temperature dependant parameters to find out which model and what kind of temperature dependant parameters should be used.

  9. High Pressure Fuel Storage Cylinders Periodic Inspection and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    from Practical Field Experience with High Pressure Gaseous Fuels Natural Gas Vehicle Cylinder Safety, Training and Inspection Project The Compelling Case for Natural Gas Vehicles...

  10. High-pressure Magic Angle Spinning Nuclear Magnetic Resonance...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    advantage of ceramic cylinders for withstanding very high-pressure utilized, but also plastic bushings can be glued tightly in place so that other plastic sealing mechanisms...

  11. Sandia National Laboratories: structural material at high pressure

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    structural material at high pressure ECIS-I2CNER: Hydrogen Infrastructure Research Aids Energy Independence Goal On February 14, 2013, in CRF, Energy, Livermore Valley Open Campus...

  12. Energy Systems High Pressure Test Laboratory (Fact Sheet), NREL...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    National laboratories Contact Us If you are interested in working with NREL's Energy Systems High Pressure Test Laboratory, please contact: ESIF Manager Carolyn Elam...

  13. Notes 11. High pressure floating ring seals

    E-Print Network [OSTI]

    San Andres, Luis

    2009-01-01T23:59:59.000Z

    Floating ring seals for compressors: leakage and force coefficients, seal lock up and effect on rotor stability, recommendations to reduce seal cross-coupled effects. Long oil seals as pressure barriers in industrial mixers: leakage and force...

  14. Oxide vapor distribution from a high-frequency sweep e-beam system

    SciTech Connect (OSTI)

    Chow, R.; Tassano, P.L.; Tsujimoto, N.

    1995-03-01T23:59:59.000Z

    Oxide vapor distributions have been determined as a function of operating parameters of a high frequency sweep e-beam source combined with a programmable sweep controller. We will show which parameters are significant, the parameters that yield the broadest oxide deposition distribution, and the procedure used to arrive at these conclusions. A design-of-experimental strategy was used with five operating parameters: evaporation rate, sweep speed, sweep pattern (pre-programmed), phase speed (azimuthal rotation of the pattern), profile (dwell time as a function of radial position). A design was chosen that would show which of the parameters and parameter pairs have a statistically significant effect on the vapor distribution. Witness flats were placed symmetrically across a 25 inches diameter platen. The stationary platen was centered 24 inches above the e-gun crucible. An oxide material was evaporated under 27 different conditions. Thickness measurements were made with a stylus profilometer. The information will enable users of the high frequency e-gun systems to optimally locate the source in a vacuum system and understand which parameters have a major effect on the vapor distribution.

  15. Synthesis, structure and properties of high pressure and ambient pressure ternary vanadium oxides 

    E-Print Network [OSTI]

    Markkula, Mikael

    2013-11-28T23:59:59.000Z

    Transition metal oxides have been extensively studied during past decades. The purpose of this research was to synthesize new or little characterised transition metal oxides using high-pressure/high-temperature (HPHT) ...

  16. “Multi-temperature” method for high-pressure sorption measurements on moist shales

    SciTech Connect (OSTI)

    Gasparik, Matus; Ghanizadeh, Amin; Gensterblum, Yves; Krooss, Bernhard M. [Energy and Mineral Resources Group (EMR), Institute of Geology and Geochemistry of Petroleum and Coal, Lochnerstr. 4-20, RWTH Aachen University, 52056 Aachen (Germany)] [Energy and Mineral Resources Group (EMR), Institute of Geology and Geochemistry of Petroleum and Coal, Lochnerstr. 4-20, RWTH Aachen University, 52056 Aachen (Germany)

    2013-08-15T23:59:59.000Z

    A simple and effective experimental approach has been developed and tested to study the temperature dependence of high-pressure methane sorption in moist organic-rich shales. This method, denoted as “multi-temperature” (short “multi-T”) method, enables measuring multiple isotherms at varying temperatures in a single run. The measurement of individual sorption isotherms at different temperatures takes place in a closed system ensuring that the moisture content remains constant. The multi-T method was successfully tested for methane sorption on an organic-rich shale sample. Excess sorption isotherms for methane were measured at pressures of up to 25 MPa and at temperatures of 318.1 K, 338.1 K, and 348.1 K on dry and moisture-equilibrated samples. The measured isotherms were parameterized with a 3-parameter Langmuir-based excess sorption function, from which thermodynamic sorption parameters (enthalpy and entropy of adsorption) were obtained. Using these, we show that by taking explicitly into account water vapor as molecular species in the gas phase with temperature-dependent water vapor pressure during the experiment, more meaningful results are obtained with respect to thermodynamical considerations. The proposed method can be applied to any adsorbent system (coals, shales, industrial adsorbents) and any supercritical gas (e.g., CH{sub 4}, CO{sub 2}) and is particularly suitable for sorption measurements using the manometric (volumetric) method.

  17. Low-temperature germanium ultra-high vacuum chemical vapor deposition for back-end photonic integration

    E-Print Network [OSTI]

    Kimerling, Lionel C.

    Polycrystalline germanium (poly-Ge) grown on amorphous Si (a-Si) by ultra-high vacuum chemical vapor deposition (UHVCVD) over oxide barriers at low temperatures (Tles450degC) exhibits a larger grain size and lower defect ...

  18. Variation in rectal temperature, respiratory rate, and pulse rate of cattle as related to variations in solar radiation, air temperature, wind velocity, and vapor pressure

    E-Print Network [OSTI]

    Quazi, Mohammad Fazlur Rahim

    1955-01-01T23:59:59.000Z

    VARIATION IN RECTAL TEMPERATURE, RESPIRATORY RATE, AND PULSE RATE GF CATTLE AS RELATED TO VARIATIONS IN SOLAR RADIATION, AIR TEMPERATURE, WIND VELOCITY, AND VAPOR PRESSURE A Dissertation By Mohammad Fazlur Rahim Quazi Approved as to style... Dissertation By Mohammad Fazlur Rahim tyiazi Submitted to the Graduate School of the Agricultural and Mechanical College of Texas in partial fulfillment of the requirements for the degree of DOCTOR OF PHILOSOPHY May 1955 Major Subject: Genetics ? ?4...

  19. A temperature compensated pressure transducer for high temperature, high pressure applications

    E-Print Network [OSTI]

    Lippka, Sandra Margaret

    1991-01-01T23:59:59.000Z

    and content by: 2/J David G. ansson (Chair ol' Committee) c. Y~ Christian P Burger (i&Iember) Randall Getger ( Member) 5wc Fr~. Walter F. Bradley (Head of Department) May 1991 ABSTRACT A Temperature Compensated Pressure Transducer for High... of the light beam. A compensation schenle is provided through the use of thermally arljusting reflecting surfaces These surfaces can adjust for temperatures up to 1000'F with less than a. I, c error. The final light beam movenlent across the photodiode face...

  20. High temperature pressurized high frequency testing rig and test method

    DOE Patents [OSTI]

    De La Cruz, Jose; Lacey, Paul

    2003-04-15T23:59:59.000Z

    An apparatus is described which permits the lubricity of fuel compositions at or near temperatures and pressures experienced by compression ignition fuel injector components during operation in a running engine. The apparatus consists of means to apply a measured force between two surfaces and oscillate them at high frequency while wetted with a sample of the fuel composition heated to an operator selected temperature. Provision is made to permit operation at or near the flash point of the fuel compositions. Additionally a method of using the subject apparatus to simulate ASTM Testing Method D6079 is disclosed, said method involving using the disclosed apparatus to contact the faces of prepared workpieces under a measured load, sealing the workface contact point into the disclosed apparatus while immersing said contact point between said workfaces in a lubricating media to be tested, pressurizing and heating the chamber and thereby the fluid and workfaces therewithin, using the disclosed apparatus to impart a differential linear motion between the workpieces at their contact point until a measurable scar is imparted to at least one workpiece workface, and then evaluating the workface scar.

  1. Method for controlling corrosion in thermal vapor injection gases

    DOE Patents [OSTI]

    Sperry, John S. (Houston, TX); Krajicek, Richard W. (Houston, TX)

    1981-01-01T23:59:59.000Z

    An improvement in the method for producing high pressure thermal vapor streams from combustion gases for injection into subterranean oil producing formations to stimulate the production of viscous minerals is described. The improvement involves controlling corrosion in such thermal vapor gases by injecting water near the flame in the combustion zone and injecting ammonia into a vapor producing vessel to contact the combustion gases exiting the combustion chamber.

  2. High pressure discharges in cavities formed by microfabrication techniques

    SciTech Connect (OSTI)

    Khan, B.A.; Cammack, D.A.; Pinker, R.D.; Racz, J. [Philips Electronics North America Corporation, Philips Research, Briarcliff Manor, New York 10510 (United States)] [Philips Electronics North America Corporation, Philips Research, Briarcliff Manor, New York 10510 (United States)

    1997-07-01T23:59:59.000Z

    High pressure discharges are the basis of small high intensity light sources. In this work, we demonstrate the formation of high pressure discharges, in cavities formed by applying micromachining and integrated circuit techniques to quartz substrates. Cavities containing varying amounts of mercury and argon were fabricated to obtain high pressure discharges. A high pressure mercury discharge was formed in the electrodeless cavities by exciting them with a microwave source, operating at 2.45 GHz and in the electroded cavities by applying a dc voltage. The contraction of the discharge into a high pressure arc was observed. A broad emission spectrum due to self-absorption and collisions between excited atoms and normal atoms, typical of high pressure mercury discharges, was measured. The light output and efficacy increased with increasing pressure. The measured voltage was used to estimate the pressure within the electroded cavities, which is as high as 127 atm for one of the two cavities discussed in this work. Efficacies over 40 lumens per watt were obtained for the electrodeless cavities and over 50 scr(l)m/W for the electroded cavities. {copyright} {ital 1997 American Institute of Physics.}

  3. Hydrous silicate melt at high pressure Mainak Mookherjee1

    E-Print Network [OSTI]

    Stixrude, Lars

    LETTERS Hydrous silicate melt at high pressure Mainak Mookherjee1 , Lars Stixrude2 & Bijaya Karki3 The structure and physical properties of hydrous silicate melts and the solubility of water in melts over most in structure to our finding that the water­silicate system becomes increasingly ideal at high pressure: we find

  4. accompanying high-pressure phase: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    pressure cryocooling Abstract High-pressure methods for solving Gruner, Sol M. 58 High-pressure studies of ammonia hydrates Edinburgh, University of - Research Archive Summary:...

  5. Lithium, compression and high-pressure structure

    SciTech Connect (OSTI)

    Olinger, B.; Shaner, J.W.

    1983-03-04T23:59:59.000Z

    Lithium is found to transform from a body-centered cubic (bcc) to a face-centered cubic (fcc) structure at 6.9 gigapascals (69 kilobars) and 296 kelvin. The relative volume of the bcc structured lithium at 6.9 gigapascals is 0.718, and the fcc structure is 0.25 percent denser. The bulk modulus and its pressure derivative for the bcc structure are 11.57 gigapascals and 3.4, and for the fcc structure are 13.1 gigapascals and 2.8. Extrapolation of the bcc-fcc phase boundary and the melting curve indiactes a triple point around 15 gigapascals and 500 kelvin.

  6. High pressure apparatus for transport properties study in high magnetic field

    SciTech Connect (OSTI)

    Alsmadi, A. M. (Abdel M.); Nakotte, H. (Heinrich); Honda, F.; Sechovsky, V. (Vladimir); Mikulina, O. (Olga); Kamarad, J.; Lacerda, A. H. (Alex H.)

    2002-01-01T23:59:59.000Z

    We have designed a high pressure apparatus for measuring electrical-transport properties at low temperatures, high magnetic field and hydrostatic pressure up to 10 kbar. Details of the high-pressure cell and an exemplary study on UNiAI are described and discussed briefly.

  7. Neutron scattering at high pressure D. B. McWhan

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    715 Neutron scattering at high pressure D. B. McWhan Room 1D-234, Murray Hill, New Jersey 07974, U scattering at steady-state and pulsed sources are reviewed. The pressure cells available at most neutron 10 GPa have been made. For elastic scattering, a comparison is made between neutron scattering and X

  8. Rotational viscometer for high-pressure high-temperature fluids

    DOE Patents [OSTI]

    Carr, Kenneth R. (Knoxville, TN)

    1985-01-01T23:59:59.000Z

    The invention is a novel rotational viscometer which is well adapted for use with fluids at high temperatures and/or pressures. In one embodiment, the viscometer includes a substantially non-magnetic tube having a closed end and having an open end in communication with a fluid whose viscosity is to be determined. An annular drive magnet is mounted for rotation about the tube. The tube encompasses and supports a rotatable shaft assembly which carries a rotor, or bob, for insertion in the fluid. Affixed to the shaft are (a) a second magnet which is magnetically coupled to the drive magnet and (b) a third magnet. In a typical operation, the drive magnet is rotated to turn the shaft assembly while the shaft rotor is immersed in the fluid. The viscous drag on the rotor causes the shaft assembly to lag the rotation of the drive magnet by an amount which is a function of the amount of viscous drag. A first magnetic pickup generates a waveform whose phase is a function of the angular position of the drive magnet. A second magnetic pickup generates a waveform whose phase is a function of the angular position of the third magnet. An output is generated indicative of the phase difference between the two waveforms.

  9. Energy Systems High Pressure Test Laboratory (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2011-10-01T23:59:59.000Z

    This fact sheet describes the purpose, lab specifications, applications scenarios, and information on how to partner with NREL's Energy Systems High Pressure Test Laboratory at the Energy Systems Integration Facility. The purpose of the Energy Systems High Pressure Test Laboratory at NREL's Energy Systems Integration Facility (ESIF) is to provide space where high pressure hydrogen components can be safely tested. High pressure hydrogen storage is an integral part of energy storage technology for use in fuel cell and in other distributed energy scenarios designed to effectively utilize the variability inherent with renewable energy sources. The high pressure storage laboratory is co-located with energy storage activities such as ultra-capacitors, super conducting magnetic flywheel and mechanical energy storage systems laboratories for an integrated approach to system development and demonstration. Hazards associated with hydrogen storage at pressures up to 10,000 psi include oxygen displacement, combustion, explosion, and pressurization of room air due to fast release and physical hazards associated with burst failure modes. A critical understanding of component failure modes is essential in developing reliable, robust designs that will minimize failure risk beyond the end of service life. Development of test protocol for accelerated life testing to accurately scale to real world operating conditions is essential for developing regulations, codes and standards required for safe operation. NREL works closely with industry partners in providing support of advanced hydrogen technologies. Innovative approaches to product design will accelerate commercialization into new markets. NREL works with all phases of the product design life cycle from early prototype development to final certification testing. High pressure tests are performed on hydrogen components, primarily for the validation of developing new codes and standards for high pressure hydrogen applications. The following types of tests can be performed: Performance, Component and system level efficiency, Strength of materials and hydrogen compatibility, Safety demonstration, Model validation, and Life cycle reliability.

  10. Design of a continuous fiber ceramic composite heat exchanger for high-temperature, high-pressure applications

    SciTech Connect (OSTI)

    Cho, S.M.; Seltzer, A.H.; Narayanan, T.V. [Foster Wheeler Development Corp., Livingston, NJ (United States); Shah, A.C.; Weddell, J.K. [DuPont Lanxide Composites Inc., Newark, DE (United States)

    1996-12-31T23:59:59.000Z

    A conceptual design of a continuous fiber ceramic composite (CFCC) heat exchanger for high-temperature, high-pressure applications is presented. The CFCC materials under consideration are SiC reinforced with SiC fibers manufactured using the continuous vapor infiltration process and alumina reinforced with SiC or alumina fibers manufactured using the directed metal oxidation process. These composite materials are highly resistant to high-temperature corrosive environment and possess a greater creep strength than metallic materials. Heat exchangers constructed of CFCC material may be utilized for high-temperature, high-pressure applications such as air/gas heaters in advanced energy systems and high-temperature energy recovery systems. This paper presents a design of a gas-to-air CFCC heat exchanger for the high temperature advanced furnace (HITAF) in the high-performance power system (HIPPS). The 1.38 MPa (200 psia) air is heated from 760 C (1,400 F) to 982 C (1,800 F) using the combustion products at 1,650 C (3,000 F). The heat exchanger is of a cross-parallel/counter flow type in which the tube-side air flow makes a combined parallel and counter flow arrangement with a cross-flowing combustion gas in such a way that the maximum CFCC tube temperature will not exceed a 1,260 C (2,300 F) design limit. The main heat transfer mechanism from the external hot gas to the tube-side air is that of gaseous radiation for the first few rows of the tubes, followed by convective heat transfer across the remainder of the tube bundle. The design characteristics of this high-temperature, high-pressure CFCC heat exchanger with supporting thermal, flow, structural, and vibrational analyses are presented in detail in the paper.

  11. High-pressure computational and experimental studies of energetic materials 

    E-Print Network [OSTI]

    Hunter, Steven

    2013-11-28T23:59:59.000Z

    On account of the high temperatures and pressures experienced by energetic materials during deflagration and detonation, it is important to know not only the physical properties of these materials at ambient temperatures ...

  12. DOE Hydrogen Delivery High-Pressure Tanks and Analysis Project...

    Broader source: Energy.gov (indexed) [DOE]

    the DOE Hydrogen Delivery High-Pressure Tanks and Analysis Project Review Meeting at Argonne National Laboratory. The purpose of the meeting was to review the progress and plans...

  13. Performance Assessment of Pressurized Stairs in High Rise Buildings 

    E-Print Network [OSTI]

    Bellido, Carlos; Quiroz, Antonio; Panizo, Alfonso; Torero, Jose L

    2008-12-17T23:59:59.000Z

    Pressurized stair cases are an important part of the fire safety strategy of high rise buildings. Long egress times are compensated by creating safe environments within egress staircases allowing the displacement time ...

  14. High pressure water jet cutting of sugar cane

    E-Print Network [OSTI]

    Valco, Thomas Donald

    1977-01-01T23:59:59.000Z

    HIGH PRESSURE WATER JET CUTTING OF SUGAR CANE A Thesis by THOMAS DONALD VALCO Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCE May 1977 Major Subject...: Agricultural Engineering HIGH PRESSURE WATER JET CUTTING OF SUGAR CANE A Thesis by THOMAS DONALD VALCO Approved as to style and content by: Dr. Charlie G. Coble (Chairman of Committee) Dr. Edward A. Haler (Head of Department) Mr. William H. Aldred...

  15. Low Cost, High Efficiency, High Pressure Hydrogen Storage

    SciTech Connect (OSTI)

    Mark Leavitt

    2010-03-31T23:59:59.000Z

    A technical and design evaluation was carried out to meet DOE hydrogen fuel targets for 2010. These targets consisted of a system gravimetric capacity of 2.0 kWh/kg, a system volumetric capacity of 1.5 kWh/L and a system cost of $4/kWh. In compressed hydrogen storage systems, the vast majority of the weight and volume is associated with the hydrogen storage tank. In order to meet gravimetric targets for compressed hydrogen tanks, 10,000 psi carbon resin composites were used to provide the high strength required as well as low weight. For the 10,000 psi tanks, carbon fiber is the largest portion of their cost. Quantum Technologies is a tier one hydrogen system supplier for automotive companies around the world. Over the course of the program Quantum focused on development of technology to allow the compressed hydrogen storage tank to meet DOE goals. At the start of the program in 2004 Quantum was supplying systems with a specific energy of 1.1-1.6 kWh/kg, a volumetric capacity of 1.3 kWh/L and a cost of $73/kWh. Based on the inequities between DOE targets and Quantum’s then current capabilities, focus was placed first on cost reduction and second on weight reduction. Both of these were to be accomplished without reduction of the fuel system’s performance or reliability. Three distinct areas were investigated; optimization of composite structures, development of “smart tanks” that could monitor health of tank thus allowing for lower design safety factor, and the development of “Cool Fuel” technology to allow higher density gas to be stored, thus allowing smaller/lower pressure tanks that would hold the required fuel supply. The second phase of the project deals with three additional distinct tasks focusing on composite structure optimization, liner optimization, and metal.

  16. High-Pressure Flame Speed Measurements

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh School football High School football FancyDepartment of

  17. High pressure sulfuric acid decomposition experiments for the sulfur-iodine thermochemical cycle.

    SciTech Connect (OSTI)

    Velasquez, Carlos E; Reay, Andrew R.; Andazola, James C.; Naranjo, Gerald E.; Gelbard, Fred

    2005-09-01T23:59:59.000Z

    A series of three pressurized sulfuric acid decomposition tests were performed to (1) obtain data on the fraction of sulfuric acid catalytically converted to sulfur dioxide, oxygen, and water as a function of temperature and pressure, (2) demonstrate real-time measurements of acid conversion for use as process control, (3) obtain multiple measurements of conversion as a function of temperature within a single experiment, and (4) assess rapid quenching to minimize corrosion of metallic components by undecomposed acid. All four of these objectives were successfully accomplished. This report documents the completion of the NHI milestone on high pressure H{sub 2}SO{sub 4} decomposition tests for the Sulfur-Iodine (SI) thermochemical cycle project. All heated sections of the apparatus, (i.e. the boiler, decomposer, and condenser) were fabricated from Hastelloy C276. A ceramic acid injection tube and a ceramic-sheathed thermocouple were used to minimize corrosion of hot liquid acid on the boiler surfaces. Negligible fracturing of the platinum on zirconia catalyst was observed in the high temperature decomposer. Temperature measurements at the exit of the decomposer and at the entry of the condenser indicated that the hot acid vapors were rapidly quenched from about 400 C to less than 20 C within a 14 cm length of the flow path. Real-time gas flow rate measurements of the decomposition products provided a direct measurement of acid conversion. Pressure in the apparatus was preset by a pressure-relief valve that worked well at controlling the system pressure. However, these valves sometimes underwent abrupt transitions that resulted in rapidly varying gas flow rates with concomitant variations in the acid conversion fraction.

  18. Confinement of hydrogen at high pressure in carbon nanotubes

    DOE Patents [OSTI]

    Lassila, David H. (Aptos, CA); Bonner, Brian P. (Livermore, CA)

    2011-12-13T23:59:59.000Z

    A high pressure hydrogen confinement apparatus according to one embodiment includes carbon nanotubes capped at one or both ends thereof with a hydrogen-permeable membrane to enable the high pressure confinement of hydrogen and release of the hydrogen therethrough. A hydrogen confinement apparatus according to another embodiment includes an array of multi-walled carbon nanotubes each having first and second ends, the second ends being capped with palladium (Pd) to enable the high pressure confinement of hydrogen and release of the hydrogen therethrough as a function of palladium temperature, wherein the array of carbon nanotubes is capable of storing hydrogen gas at a pressure of at least 1 GPa for greater than 24 hours. Additional apparatuses and methods are also presented.

  19. Calcium peroxide from ambient to high pressures

    E-Print Network [OSTI]

    Nelson, Joseph R.; Needs, Richard J.; Pickard, Chris J.

    2015-02-06T23:59:59.000Z

    of the University of Cambridge High Performance Computing Service (http://www.hpc.cam.ac.uk/), as well as the ARCHER UK National Supercomputing Ser- vice (http://www.archer.ac.uk/). Financial support was provided by the Engineering and Physical Sciences Re- search...

  20. Pressure Relief Devices for High-Pressure Gaseous Storage Systems: Applicability to Hydrogen Technology

    SciTech Connect (OSTI)

    Kostival, A.; Rivkin, C.; Buttner, W.; Burgess, R.

    2013-11-01T23:59:59.000Z

    Pressure relief devices (PRDs) are viewed as essential safety measures for high-pressure gas storage and distribution systems. These devices are used to prevent the over-pressurization of gas storage vessels and distribution equipment, except in the application of certain toxic gases. PRDs play a critical role in the implementation of most high-pressure gas storage systems and anyone working with these devices should understand their function so they can be designed, installed, and maintained properly to prevent any potentially dangerous or fatal incidents. As such, the intention of this report is to introduce the reader to the function of the common types of PRDs currently used in industry. Since high-pressure hydrogen gas storage systems are being developed to support the growing hydrogen energy infrastructure, several recent failure incidents, specifically involving hydrogen, will be examined to demonstrate the results and possible mechanisms of a device failure. The applicable codes and standards, developed to minimize the risk of failure for PRDs, will also be reviewed. Finally, because PRDs are a critical component for the development of a successful hydrogen energy infrastructure, important considerations for pressure relief devices applied in a hydrogen gas environment will be explored.

  1. Deposition of silicon carbide films using a high vacuum metalorganic chemical vapor deposition method with a single source precursor

    E-Print Network [OSTI]

    Boo, Jin-Hyo

    , high temperature, and high radiation environments. Conventional silicon carbide chemical vapor deposition CVD processes generally utilized multiple precursors such as silane and hydrocarbons, and required temperature alternatives to the conventional SiC CVD methods must be considered. To do this, a relatively

  2. Diamond anvil cell for spectroscopic investigation of materials at high temperature, high pressure and shear

    DOE Patents [OSTI]

    Westerfield, C.L.; Morris, J.S.; Agnew, S.F.

    1997-01-14T23:59:59.000Z

    Diamond anvil cell is described for spectroscopic investigation of materials at high temperature, high pressure and shear. A cell is described which, in combination with Fourier transform IR spectroscopy, permits the spectroscopic investigation of boundary layers under conditions of high temperature, high pressure and shear. 4 figs.

  3. Diamond anvil cell for spectroscopic investigation of materials at high temperature, high pressure and shear

    DOE Patents [OSTI]

    Westerfield, Curtis L. (Espanola, NM); Morris, John S. (Los Alamos, NM); Agnew, Stephen F. (Los Alamos, NM)

    1997-01-01T23:59:59.000Z

    Diamond anvil cell for spectroscopic investigation of materials at high temperature, high pressure and shear. A cell is described which, in combination with Fourier transform IR spectroscopy, permits the spectroscopic investigation of boundary layers under conditions of high temperature, high pressure and shear.

  4. Reinvestigation of high pressure polymorphism in hafnium metal

    SciTech Connect (OSTI)

    Pandey, K. K., E-mail: kkpandey@barc.gov.in; Sharma, Surinder M. [High Pressure and Synchrotron Radiation Physics Division, Bhabha Atomic Research Centre, Mumbai-400 085 (India); Gyanchandani, Jyoti; Dey, G. K. [Materials Science Division, Bhabha Atomic Research Centre, Mumbai-400 085 (India); Somayazulu, M. [Geophysical Laboratory, Carnegie Institution of Washington, Washington, D.C. 20015 (United States); Sikka, S. K. [Indian National Science Academy, New Delhi-110 002 (India)

    2014-06-21T23:59:59.000Z

    There has been a recent controversy about the high pressure polymorphism of Hafnium (Hf). Unlike, the earlier known ??? structural transition at 38?±?8?GPa, at ambient temperature, Hrubiak et al. [J. Appl. Phys. 111, 112612 (2012)] did not observe it till 51?GPa. They observed this transition only at elevated temperatures. We have reinvestigated the room temperature phase diagram of Hf, employing x-ray diffraction (XRD) and DFT based first principles calculations. Experimental investigations have been carried out on several pure and impure Hf samples and also with different pressure transmitting media. Besides demonstrating the significant role of impurity levels on the high pressure phase diagram of Hf, our studies re-establish room temperature ??? transition at high pressures, even in quasi-hydrostatic environment. We observed this transition in pure Hf with equilibrium transition pressure P{sub o}?=?44.5?GPa; however, with large hysteresis. The structural sequence, transition pressures, the lattice parameters, the c/a ratio and its variation with compression for the ? and ? phases as predicted by our ab-initio scalar relativistic (SR) calculations are found to be in good agreement with our experimental results of pure Hf.

  5. Effects of capillarity and vapor adsorption in the depletion of vapor-dominated geothermal reservoirs

    SciTech Connect (OSTI)

    Pruess, Karsten; O'Sullivan, Michael

    1992-01-01T23:59:59.000Z

    Vapor-dominated geothermal reservoirs in natural (undisturbed) conditions contain water as both vapor and liquid phases. The most compelling evidence for the presence of distributed liquid water is the observation that vapor pressures in these systems are close to saturated vapor pressure for measured reservoir temperatures (White et al., 1971; Truesdell and White, 1973). Analysis of natural heat flow conditions provides additional, indirect evidence for the ubiquitous presence of liquid. From an analysis of the heat pipe process (vapor-liquid counterflow) Preuss (1985) inferred that effective vertical permeability to liquid phase in vapor-dominated reservoirs is approximately 10{sup 17} m{sup 2}, for a heat flux of 1 W/m{sup 2}. This value appears to be at the high end of matrix permeabilities of unfractured rocks at The Geysers, suggesting that at least the smaller fractures contribute to liquid permeability. For liquid to be mobile in fractures, the rock matrix must be essentially completely liquid-saturated, because otherwise liquid phase would be sucked from the fractures into the matrix by capillary force. Large water saturation in the matrix, well above the irreducible saturation of perhaps 30%, has been shown to be compatible with production of superheated steam (Pruess and Narasimhan, 1982). In response to fluid production the liquid phase will boil, with heat of vaporization supplied by the reservoir rocks. As reservoir temperatures decline reservoir pressures will decline also. For depletion of ''bulk'' liquid, the pressure would decline along the saturated vapor pressure curve, while for liquid held by capillary and adsorptive forces inside porous media, an additional decline will arise from ''vapor pressure lowering''. Capillary pressure and vapor adsorption effects, and associated vapor pressure lowering phenomena, have received considerable attention in the geothermal literature, and also in studies related to geologic disposal of heat generating nuclear wastes, and in the drying of porous materials. Geothermally oriented studies were presented by Chicoine et al. (1977), Hsieh and Ramey (1978, 1981), Herkelrath et al. (1983), and Nghiem and Ramey (1991). Nuclear waste-related work includes papers by Herkelrath and O'Neal (1985), Pollock (1986), Eaton and Bixler (1987), Pruess et al. (1990), Nitao (1990), and Doughty and E'ruess (1991). Applications to industrial drying of porous materials have been discussed by Hamiathy (1969) arid Whitaker (1977). This paper is primarily concerned with evaluating the impact of vapor pressure lowering (VPL) effects on the depletion behavior of vapor-dominated reservoirs. We have examined experimental data on vapor adsorption and capillary pressures in an effort to identify constitutive relationships that would be applicable to the tight matrix rocks of vapor-dominated systems. Numerical simulations have been performed to evaluate the impact of these effects on the depletion of vapor-dominated reservoirs.

  6. accumulate high concentrations: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    high pressure chemical vapor deposition have been studied by high-resolution electron energy loss spectroscopy HREELS and room temperature infrared reflection measurements. HREEL...

  7. An experimental investigation of high temperature, high pressure paper drying 

    E-Print Network [OSTI]

    Patel, Kamal Raoji

    1994-01-01T23:59:59.000Z

    T=1 49 oc alternate T 204 oc some T= 204 oc atternote 2 4 6 6 10 12 Number of Passes o el 0 E ta el J O Sl o el I 0 0. 9 0. 8 0. 7 0. 6 0. 5 0, 4 0. 3 02 0. 1 0. 0 contac t pressure 1. 4 MPa T= 93 aC some T= 93a...C alternate ? a ? T=149 OC Same T=149 ocalternate T=204 oc same T=204 oc alternate 0 2 4 6 8 10 12 Number of Passes 1. 0 0. 9 0. 8 CL I3 07 0 0. 6 le 0. 5 ln 0. 4 0 0. 3 o 0. 2 0. 1 0. 0 contac t pressure 2. 1 MPa I . z' ~ T= 93 oC some...

  8. High Temperature, High Pressure Devices for Zonal Isolation in Geothermal Wells

    Broader source: Energy.gov [DOE]

    DOE Geothermal Peer Review 2010 - Presentation. Project objectives: Design, demonstrate, and qualify high-temperature high pressure zonal isolation devices compatible with the high temperature downhole Enhanced Geothermal Systems (EGS) environment.

  9. Ultra-high pressure water jet: Baseline report

    SciTech Connect (OSTI)

    NONE

    1997-07-31T23:59:59.000Z

    The ultra-high pressure waterjet technology was being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers the evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The ultra-high pressure waterjet technology acts as a cutting tool for the removal of surface substrates. The Husky{trademark} pump feeds water to a lance that directs the high pressure water at the surface to be removed. The safety and health evaluation during the testing demonstration focused on two main areas of exposure. These were dust and noise. The dust exposure was found to be minimal, which would be expected due to the wet environment inherent in the technology, but noise exposure was at a significant level. Further testing for noise is recommended because of the outdoor environment where the testing demonstration took place. In addition, other areas of concern found were arm-hand vibration, ergonomics, heat stress, tripping hazards, electrical hazards, lockout/tagout, fall hazards, slipping hazards, hazards associated with the high pressure water, and hazards associated with air pressure systems.

  10. LX-17 Deflagration at High Pressures and Temperatures

    SciTech Connect (OSTI)

    Koerner, J; Maienschein, J; Black, K; DeHaven, M; Wardell, J

    2006-10-23T23:59:59.000Z

    We measure the laminar deflagration rate of LX-17 (92.5 wt% TATB, 7.5 wt% Kel-F 800) at high pressure and temperature in a strand burner, thereby obtaining reaction rate data for prediction of thermal explosion violence. Simultaneous measurements of flame front time-of-arrival and temporal pressure history allow for the direct calculation of deflagration rate as a function of pressure. Additionally, deflagrating surface areas are calculated in order to provide quantitative insight into the dynamic surface structure during deflagration and its relationship to explosion violence. Deflagration rate data show that LX-17 burns in a smooth fashion at ambient temperature and is represented by the burn rate equation B = 0.2P{sup 0.9}. At 225 C, deflagration is more rapid and erratic. Dynamic deflagrating surface area calculations show that ambient temperature LX-17 deflagrating surface areas remain near unity over the pressure range studied.

  11. Two-Phase Flow Pressure Drop of High Quality Steam

    SciTech Connect (OSTI)

    Curtis, J. M.; Coffield, R. D.

    2001-10-01T23:59:59.000Z

    Two-phase pressure drop across a straight test pipe was experimentally determined for high Reynolds (Re) number steam flow for a flow quality range of 0.995 to 1.0. The testing described has been performed in order to reduce uncertainties associated with the effects of two-phase flow on pressure drop. Two-phase flow develops in steam piping because a small fraction of the steam flow condenses due to heat loss to the surroundings. There has been very limited two-phase pressure drop data in open literature for the tested flow quality range. The two-phase pressure drop data obtained in this test has enabled development of a correlation between friction factor, Reynolds number, and flow quality.

  12. Microhole High-Pressure Jet Drill for Coiled Tubing

    SciTech Connect (OSTI)

    Ken Theimer; Jack Kolle

    2007-06-30T23:59:59.000Z

    Tempress Small Mechanically-Assisted High-Pressure Waterjet Drilling Tool project centered on the development of a downhole intensifier (DHI) to boost the hydraulic pressure available from conventional coiled tubing to the level required for high-pressure jet erosion of rock. We reviewed two techniques for implementing this technology (1) pure high-pressure jet drilling and (2) mechanically-assisted jet drilling. Due to the difficulties associated with modifying a downhole motor for mechanically-assisted jet drilling, it was determined that the pure high-pressure jet drilling tool was the best candidate for development and commercialization. It was also determined that this tool needs to run on commingled nitrogen and water to provide adequate downhole differential pressure and to facilitate controlled pressure drilling and descaling applications in low pressure wells. The resulting Microhole jet drilling bottomhole assembly (BHA) drills a 3.625-inch diameter hole with 2-inch coil tubing. The BHA consists of a self-rotating multi-nozzle drilling head, a high-pressure rotary seal/bearing section, an intensifier and a gas separator. Commingled nitrogen and water are separated into two streams in the gas separator. The water stream is pressurized to 3 times the inlet pressure by the downhole intensifier and discharged through nozzles in the drilling head. The energy in the gas-rich stream is used to power the intensifier. Gas-rich exhaust from the intensifier is conducted to the nozzle head where it is used to shroud the jets, increasing their effective range. The prototype BHA was tested at operational pressures and flows in a test chamber and on the end of conventional coiled tubing in a test well. During instrumented runs at downhole conditions, the BHA developed downhole differential pressures of 74 MPa (11,000 psi, median) and 90 MPa (13,000 psi, peaks). The median output differential pressure was nearly 3 times the input differential pressure available from the coiled tubing. In a chamber test, the BHA delivered up to 50 kW (67 hhp) hydraulic power. The tool drilled uncertified class-G cement samples cast into casing at a rate of 0.04 to 0.17 m/min (8 to 33 ft/hr), within the range projected for this tool but slower than a conventional PDM. While the tool met most of the performance goals, reliability requires further improvement. It will be difficult for this tool, as currently configured, to compete with conventional positive displacement downhole motors for most coil tubing drill applications. Mechanical cutters on the rotating nozzle head would improve cutting. This tool can be easily adapted for well descaling operations. A variant of the Microhole jet drilling gas separator was further developed for use with positive displacement downhole motors (PDM) operating on commingled nitrogen and water. A fit-for-purpose motor gas separator was designed and yard tested within the Microhole program. Four commercial units of that design are currently involved in a 10-well field demonstration with Baker Oil Tools in Wyoming. Initial results indicate that the motor gas separators provide significant benefit.

  13. High Pressure Hydrogen Materials Compatibility of Piezoelectric Films

    SciTech Connect (OSTI)

    Alvine, Kyle J.; Shutthanandan, V.; Bennett, Wendy D.; Bonham, Charles C.; Skorski, Daniel C.; Pitman, Stan G.; Dahl, Michael E.; Henager, Charles H.

    2010-12-02T23:59:59.000Z

    Abstract: Hydrogen is being considered as a next-generation clean burning fuel. However, hydrogen has well known materials issues, including blistering and embrittlement in metals. Piezoelectric materials are used as actuators in hydrogen fuel technology. We present studies of materials compatibility of piezoelectric films in a high pressure hydrogen environment. Absorption of high pressure hydrogen was studied with Elastic Recoil Detection Analysis (ERDA) and Rutherford Back Scattering (RBS) in lead zirconate titanate (PZT) and barium titanate (BTO) thin films. Hydrogen surface degradation in the form of blistering and Pb mixing was also observed.

  14. Capillary toroid cavity detector for high pressure NMR

    DOE Patents [OSTI]

    Gerald, II, Rex E. (Brookfield, IL); Chen, Michael J. (Downers Grove, IL); Klingler, Robert J. (Glenview, IL); Rathke, Jerome W. (Honer Glen, IL); ter Horst, Marc (Chapel Hill, NC)

    2007-09-11T23:59:59.000Z

    A Toroid Cavity Detector (TCD) is provided for implementing nuclear magnetic resonance (NMR) studies of chemical reactions under conditions of high pressures and temperatures. A toroid cavity contains an elongated central conductor extending within the toroid cavity. The toroid cavity and central conductor generate an RF magnetic field for NMR analysis. A flow-through capillary sample container is located within the toroid cavity adjacent to the central conductor to subject a sample material flowing through the capillary to a static magnetic field and to enable NMR spectra to be recorded of the material in the capillary under a temperature and high pressure environment.

  15. Numerical Model Investigation for Potential Methane Explosion and Benzene Vapor Intrusion Associated with High-Ethanol Blend

    E-Print Network [OSTI]

    Alvarez, Pedro J.

    ABSTRACT: Ethanol-blended fuel releases usually stimulate methanogenesis in the subsurface, which could conditions exist. Ethanol- derived methane may also increase the vapor intrusion potential of toxic fuel to be modified when dealing with some high ethanol blend fuel (i.e., E20 up to E95) releases. INTRODUCTION

  16. Ultra-high pressure water jet: Baseline report; Summary

    SciTech Connect (OSTI)

    NONE

    1997-07-31T23:59:59.000Z

    The Husky{trademark} is an ultra high pressure waterjet cutting tool system. The pump is mounted on a steel tube frame which includes slots for transport by a forklift. The Husky{trademark} features an automatic shutdown for several conditions such as low oil pressure and high oil temperature. Placement of the Husky{trademark} must allow for a three foot clearance on all sides for operation and service access. At maximum continuous operation, the output volume is 7.2 gallons per minute with an output pressure of 40,000 psi. A diesel engine provides power for the system. The safety and health evaluation during the human factors assessment focused on two main areas: noise and dust.

  17. Guest disorder and high pressure behavior of argon hydrates

    SciTech Connect (OSTI)

    Yang, L.; Tulk, C.A.; Klug, D.D.; Chakoumakos, B.C.; Ehm, L.; Molaison, J.J.; Parise, J.B.; Simonson, J.M. (NRCC); (SBU); (ORNL)

    2010-03-29T23:59:59.000Z

    The structure of argon hydrate was studied at ambient pressure and low temperature, and between 1.7 and 4.2 GPa at 295 K. This analysis produced a single Ar guest atom, positionally disordered off-center in the large cages of sII. Above 1.7 GPa Ar clathrate transformed to a mixture of a body-centered orthorhombic filled-ice phase, which can be viewed as a polytype of ice-Ih, and high pressure forms of pure ice. The guest disorder is further substantiated by analysis of the guest to host ratio in this high pressure filled-ice structure. The bulk modulus of Ar filled-ice found to be 11.7 {+-} 0.4 GPa.

  18. Pressure dependence on the reaction propagation rate of PETN at high pressure

    SciTech Connect (OSTI)

    Foltz, M.F.

    1993-04-01T23:59:59.000Z

    The reaction propagation rate (RPR) of the sensitive high explosive pentaerythritol tetranitrate (PETN) was measured in a diamond anvil cell (DAC) over the pressure range of 2--20 GPa. The experimental technique used is the same as that previously reported. The RPR data shows that it burns one to two orders of magnitude faster in the DAC than 1,3,5,-triamino-2,4,6-trinitrobenzene (TATB) and nitromethane (CH{sub 3}NO{sub 2}) respectively. The PETN RPR curve did not show sample pressure-dependent behavior like that of nitromethane, but instead varied abruptly like the RPR curve of TATB. In order to interpret these changes, static-pressure DAC mid-IR FTIR spectra were taken of micro-pellets of PETN embedded in KBr. The relationship between changes in the spectra, the RPR curve, and published single crystal PETN wedge test data are discussed.

  19. Low pressure high speed Stirling air engine. Final technical report

    SciTech Connect (OSTI)

    Ross, M.A.

    1980-06-16T23:59:59.000Z

    The purpose of this project was to design, construct and test a simple, appropriate technology low pressure, high speed, wood-fired Stirling air engine of 100 W output. The final design was a concentric piston/displacer engine of 454 in. bore and 1 in. stroke with a rhombic drive mechanism. The project engine was ultimately completed and tested, using a propane burner for all tests as a matter of convenience. The 100 W aim was exceeded, at atmospheric pressure, over a wide range of engine speed with the maximum power being 112 W at 1150 rpm. A pressure can was constructed to permit pressurization; however the grant funds were running out, and the only pressurized power test attempted was unsuccessful due to seal difficulties. This was a disappointment because numerous tests on the 4 cubic inch engine suggested power would be more than doubled with pressurization at 25 psig. A manifold was designed and constructed to permit operation of the engine over a standard No. 40 pot bellied stove. The engine was run successfully, but at reduced speed and power, over this stove. The project engine started out being rather noisy in operation, but modifications ultimately resulted in a very quiet engine. Various other difficulties and their solutions also are discussed. (LCL)

  20. High-temperature pressure-coupled ultrasonic waveguide

    DOE Patents [OSTI]

    Caines, M.J.

    1981-02-11T23:59:59.000Z

    A pressure coupled ultrasonic waveguide is provided to which one end may be attached a transducer and at the other end a high temperature material for continuous ultrasonic testing of the material. The ultrasonic signal is coupled from the waveguide into the material through a thin, dry copper foil.

  1. Keep the Beat: Control Your High Blood Pressure

    E-Print Network [OSTI]

    Bandettini, Peter A.

    Keep the Beat: Control Your High Blood Pressure Healthy Hearts, Healthy Homes #12;Read other The NHLBI Information Center is a service of the National Heart, Lung, and Blood Institute (NHLBI, patients, and the public about the treatment, diagnosis, and prevention of heart, lung, and blood diseases

  2. Reduction of Film Coolant in High Pressure Turbines

    E-Print Network [OSTI]

    Wirsum Institute of Power Plant Technology, Steam and Gas Turbines, RWTH Aachen Prof. Dr.-Ing. Ingo RöhleReduction of Film Coolant in High Pressure Turbines Bachelor Thesis in Computational Engineering Institute of Propulsion Technology, German Aerospace Center #12;Abstract Gas turbine development has been

  3. Absolute integrated intensities of vapor-phase hydrogen peroxide...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Absolute integrated intensities of vapor-phase hydrogen peroxide (H202) in the mid-infrared at atmospheric pressure. Absolute integrated intensities of vapor-phase hydrogen...

  4. Experimental Investigation on High-pressure, High-temperature Viscosity of Gas Mixtures

    E-Print Network [OSTI]

    Davani, Ehsan

    2012-02-14T23:59:59.000Z

    Modeling the performance of high-pressure, high-temperature (HPHT) natural gas reservoirs requires the understanding of gas behavior at such conditions. In particular, gas viscosity is an important fluid property that directly affects fluid flow...

  5. Numerical Modeling of Cased-hole Instability in High Pressure and High Temperature Wells 

    E-Print Network [OSTI]

    Shen, Zheng 1983-

    2012-11-12T23:59:59.000Z

    of cemented sections in High Pressure High Temperature (HPHT) wells. The existing analysis shows that, in the perforation zones, casing/cement is subject to instability, particularly in the presence of cavities. This dissertation focuses on the instability...

  6. Surface roughening of superalloys by high pressure pure waterjet

    SciTech Connect (OSTI)

    Taylor, T.A. [Praxair Surface Technologies Inc., Indianapolis, IN (United States)

    1995-12-31T23:59:59.000Z

    A high pressure waterjet has been used to study the surface roughening of superalloys as preparation for thermal spraying. Designed experiments for Mar-M 509 and Rene 80 were carried out for the effects of jet pressure and mass of water delivered per unit area. Comparisons were made of several superalloys in terms of erosion, surface roughness and topology. The mechanism of jet erosion of Rene 80 was studied in relation to its metallurgical microstructure. An MCrAlY coating by shrouded plasma spray was made over a waterjet prepared surface with excellent bonding and having an ideally clean interface.

  7. Aging study of boiling water reactor high pressure injection systems

    SciTech Connect (OSTI)

    Conley, D.A.; Edson, J.L.; Fineman, C.F. [Lockheed Idaho Technologies Co., Idaho Falls, ID (United States)

    1995-03-01T23:59:59.000Z

    The purpose of high pressure injection systems is to maintain an adequate coolant level in reactor pressure vessels, so that the fuel cladding temperature does not exceed 1,200{degrees}C (2,200{degrees}F), and to permit plant shutdown during a variety of design basis loss-of-coolant accidents. This report presents the results of a study on aging performed for high pressure injection systems of boiling water reactor plants in the United States. The purpose of the study was to identify and evaluate the effects of aging and the effectiveness of testing and maintenance in detecting and mitigating aging degradation. Guidelines from the United States Nuclear Regulatory Commission`s Nuclear Plant Aging Research Program were used in performing the aging study. Review and analysis of the failures reported in databases such as Nuclear Power Experience, Licensee Event Reports, and the Nuclear Plant Reliability Data System, along with plant-specific maintenance records databases, are included in this report to provide the information required to identify aging stressors, failure modes, and failure causes. Several probabilistic risk assessments were reviewed to identify risk-significant components in high pressure injection systems. Testing, maintenance, specific safety issues, and codes and standards are also discussed.

  8. Millimeter-wave Radiometer for High Sensitivity Water Vapor Profiling in Arid Regions

    SciTech Connect (OSTI)

    Pazmany, Andrew

    2006-11-09T23:59:59.000Z

    Abstract - ProSensing Inc. has developed a G-band (183 GHz) water Vapor Radiometer (GVR) for long-term, unattended measurements of low concentrations of atmospheric water vapor and liquid water. Precipitable water vapor and liquid water path are estimated from zenith brightness temperatures measured from four double-sideband receiver channels, centered at 183.31 1, 3 and 7, and 14 GHz. A prototype ground-based version of the instrument was deployed at the DOE ARM program?s North Slope of Alaska site near Barrow AK in April 2005, where it collected data continuously for one year. A compact, airborne version of this instrument, packaged to operate from a standard 2-D PMS probe canister, has been tested on the ground and is scheduled for test flights in the summer of 2006. This paper presents design details, laboratory test results and examples of retrieved precipitable water vapor and liquid water path from measured brightness temperature data.

  9. Film boiling of saturated liquid flowing upward through a heated tube : high vapor quality range

    E-Print Network [OSTI]

    Laverty, W. F.

    1964-01-01T23:59:59.000Z

    Film boiling of saturated liquid flowing upward through a uniformly heated tube has been studied for the case in which pure saturated liquid enters the tube and nearly saturated vapor is discharged. Since a previous study ...

  10. Effects of pressure, temperature, and hydrogen during graphene growth on SiC(0001) using propane-hydrogen chemical vapor deposition

    SciTech Connect (OSTI)

    Michon, A.; Vezian, S.; Roudon, E.; Lefebvre, D.; Portail, M. [CNRS-CRHEA, Rue Bernard Gregory, 06560 Valbonne (France)] [CNRS-CRHEA, Rue Bernard Gregory, 06560 Valbonne (France); Zielinski, M.; Chassagne, T. [NOVASiC, Savoie Technolac, Arche Bat 4, BP267, 73375 Le Bourget du Lac (France)] [NOVASiC, Savoie Technolac, Arche Bat 4, BP267, 73375 Le Bourget du Lac (France)

    2013-05-28T23:59:59.000Z

    Graphene growth from a propane flow in a hydrogen environment (propane-hydrogen chemical vapor deposition (CVD)) on SiC differentiates from other growth methods in that it offers the possibility to obtain various graphene structures on the Si-face depending on growth conditions. The different structures include the (6{radical}3 Multiplication-Sign 6{radical}3)-R30 Degree-Sign reconstruction of the graphene/SiC interface, which is commonly observed on the Si-face, but also the rotational disorder which is generally observed on the C-face. In this work, growth mechanisms leading to the formation of the different structures are studied and discussed. For that purpose, we have grown graphene on SiC(0001) (Si-face) using propane-hydrogen CVD at various pressure and temperature and studied these samples extensively by means of low energy electron diffraction and atomic force microscopy. Pressure and temperature conditions leading to the formation of the different structures are identified and plotted in a pressure-temperature diagram. This diagram, together with other characterizations (X-ray photoemission and scanning tunneling microscopy), is the basis of further discussions on the carbon supply mechanisms and on the kinetics effects. The entire work underlines the important role of hydrogen during growth and its effects on the final graphene structure.

  11. High Pressure Burn Rate Measurements on an Ammonium Perchlorate Propellant

    SciTech Connect (OSTI)

    Glascoe, E A; Tan, N

    2010-04-21T23:59:59.000Z

    High pressure deflagration rate measurements of a unique ammonium perchlorate (AP) based propellant are required to design the base burn motor for a Raytheon weapon system. The results of these deflagration rate measurements will be key in assessing safety and performance of the system. In particular, the system may experience transient pressures on the order of 100's of MPa (10's kPSI). Previous studies on similar AP based materials demonstrate that low pressure (e.g. P < 10 MPa or 1500 PSI) burn rates can be quite different than the elevated pressure deflagration rate measurements (see References and HPP results discussed herein), hence elevated pressure measurements are necessary in order understand the deflagration behavior under relevant conditions. Previous work on explosives have shown that at 100's of MPa some explosives will transition from a laminar burn mechanism to a convective burn mechanism in a process termed deconsolidative burning. The resulting burn rates that are orders-of-magnitude faster than the laminar burn rates. Materials that transition to the deconsolidative-convective burn mechanism at elevated pressures have been shown to be considerably more violent in confined heating experiments (i.e. cook-off scenarios). The mechanisms of propellant and explosive deflagration are extremely complex and include both chemical, and mechanical processes, hence predicting the behavior and rate of a novel material or formulation is difficult if not impossible. In this work, the AP/HTPB based material, TAL-1503 (B-2049), was burned in a constant volume apparatus in argon up to 300 MPa (ca. 44 kPSI). The burn rate and pressure were measured in-situ and used to calculate a pressure dependent burn rate. In general, the material appears to burn in a laminar fashion at these elevated pressures. The experiment was reproduced multiple times and the burn rate law using the best data is B = (0.6 {+-} 0.1) x P{sup (1.05{+-}0.02)} where B is the burn rate in mm/s and P is the pressure in units of MPa. Details of the experimental method, results and data analysis are discussed herein and briefly compared to other AP based materials that have been measured in this apparatus.

  12. High-pressure lubricity at the meso- and nanoscale

    E-Print Network [OSTI]

    A. Vanossi; A. Benassi; N. Varini; E. Tosatti

    2013-01-11T23:59:59.000Z

    The increase of sliding friction upon increasing load is a classic in the macroscopic world. Here we discuss the possibility that friction rise might sometimes turn into a drop when, at the mesoscale and nanoscale, a confined lubricant film separating crystalline sliders undergoes strong layering and solidification. Under pressure, transitions from N to N-1 layers may imply a change of lateral periodicity of the crystallized lubricant sufficient to alter the matching of crystal structures, influencing the ensuing friction jump. A pressure-induced friction drop may occur as the shear gradient maximum switches from the lubricant middle, marked by strong stick-slip with or without shear melting, to the crystalline slider-lubricant interface, characterized by smooth superlubric sliding. We present high pressure sliding simulations to display examples of frictional drops, suggesting their possible relevance to the local behavior in boundary lubrication.

  13. Modified approaches for high pressure filtration of fine clean coal

    SciTech Connect (OSTI)

    Yang, J.; Groppo, J.G.; Parekh, B.K. [Center for Applied Energy Research, Lexington, KY (United States)

    1995-12-31T23:59:59.000Z

    Removal of moisture from fine (minus 28 mesh) clean coal to 20% or lower level is difficult using the conventional vacuum dewatering technique. High pressure filtration technique provides an avenue for obtaining low moisture in fine clean coal. This paper describes a couple of novel approaches for dewatering of fine clean coal using pressure filtration which provides much lower moisture in fine clean coal than that obtained using conventional pressure filter. The approaches involve (a) split stream dewatering and (b) addition of paper pulp to the coal slurry. For Pittsburgh No. 8 coal slurry, split stream dewatering at 400 mesh provided filter cake containing 12.9% moisture compared to 24.9% obtained on the feed material. The addition of paper pulp to the slurry provided filter cake containing about 17% moisture.

  14. High pressure argon ionization chamber systems for the measurement of environmental radiation exposure rates

    E-Print Network [OSTI]

    DeCampo, J A; Raft, P D

    1972-01-01T23:59:59.000Z

    High pressure argon ionization chamber systems for the measurement of environmental radiation exposure rates

  15. Proposal for high pressure RF cavity test in the MTA

    SciTech Connect (OSTI)

    Yonehara, K.; /Fermilab

    2010-09-01T23:59:59.000Z

    In order to demonstrate the feasibility of high pressure hydrogen gas filled RF (HPRF) cavities for muon ionization cooling, an HPRF cavity must be tested with a high intensity charged beam. When an HPRF cavity is irradiated with an intense beam each incident particle generates about 1000 electrons and ions per cubic centimeter in a high pressure cavity via ionization. These ionization electrons are influenced by the RF field and the RF quality factor goes down. This Q factor reduction will be a problem with a multi bunch beam, e.g., a muon beam for a muon collider consists of a 12 to 20 bunch train beam with 5 ns timing gap. Thus, the RF field must recover in few nano seconds. We propose to use a 400 MeV proton beam in the MTA and measure a beam loading effect in the HPRF cavity and study the recovery mechanism of the RF field.

  16. Numerical simulation of transient, incongruent vaporization induced by high power laser

    SciTech Connect (OSTI)

    Tsai, C.H.

    1981-01-01T23:59:59.000Z

    A mathematical model and numerical calculations were developed to solve the heat and mass transfer problems specifically for uranum oxide subject to laser irradiation. It can easily be modified for other heat sources or/and other materials. In the uranium-oxygen system, oxygen is the preferentially vaporizing component, and as a result of the finite mobility of oxygen in the solid, an oxygen deficiency is set up near the surface. Because of the bivariant behavior of uranium oxide, the heat transfer problem and the oxygen diffusion problem are coupled and a numerical method of simultaneously solving the two boundary value problems is studied. The temperature dependence of the thermal properties and oxygen diffusivity, as well as the highly ablative effect on the surface, leads to considerable non-linearities in both the governing differential equations and the boundary conditions. Based on the earlier work done in this laboratory by Olstad and Olander on Iron and on Zirconium hydride, the generality of the problem is expanded and the efficiency of the numerical scheme is improved. The finite difference method, along with some advanced numerical techniques, is found to be an efficient way to solve this problem.

  17. Momentum and thermal boundary-layer thickness in a stagnation flow chemical vapor deposition reactor

    E-Print Network [OSTI]

    Dandy, David

    reactor David S. Dandy and Jungheum Yun Department of Chemical Engineering, Colorado State University stagnation flows characteristic of highly convective chemical vapor deposition pedestal reactors. Expressions of diamond via low- pressure chemical vapor deposition, direct current (dc) arcjet reactor systems3­8 have

  18. High-Pressure MOF Research Yields Structural Insights

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh School football High School football FancyDepartment ofHigh-Pressure

  19. High-Pressure MOF Research Yields Structural Insights

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh School football High School football FancyDepartmentHigh-Pressure MOF

  20. High-Pressure MOF Research Yields Structural Insights

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh School football High School football FancyDepartmentHigh-Pressure

  1. High-Pressure MOF Research Yields Structural Insights

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh School football High School footballHigh-Pressure MOF Research Yields

  2. High Pressure Scanning Tunneling Microscopy and High Pressure X-ray Photoemission Spectroscopy Studies of Adsorbate Structure, Composition and Mobility during Catalytic Reactions on A Model Single Crystal

    E-Print Network [OSTI]

    Montano, M.O.

    2006-01-01T23:59:59.000Z

    Guntherodt, H. -J. , Eds. Scanning Tunneling Microscopy III;157. Chapter 7 : High-Pressure Scanning Tunneling Microscopypressure high-temperature scanning tunneling microscope and

  3. Intermittently-fed high-pressure gasifier process

    DOE Patents [OSTI]

    Bailey, J.M.; Zadoks, A.L.

    1993-11-30T23:59:59.000Z

    An improved gasifier is described which is adapted for gasifying a predetermined charge of non-gaseous fuel into fuel gas. Each charge of non-gaseous fuel, which may have optional conditioning materials added to it, is intermittently fed to a gasifier chamber where each charge is partially burned with high-pressure air supplied thereto. High-pressure and temperature fuel gas is produced which is cleansed prior to passing out of the gasifier chamber. After gasification of the charge of fuel is ended, the gasifier chamber is vented. The residue of the burned charge in the gasifier chamber is removed, along with the contaminated or reacted conditioning materials, and replaced by a fresh charge. The subject invention provides a feasible way of continuously fueling an internal combustion engine with gasified fuel and is compact enough to be practical for even mobile applications. 3 figures.

  4. Intermittently-fed high-pressure gasifier process

    DOE Patents [OSTI]

    Bailey, John M. (Dunlap, IL); Zadoks, Abraham L. (Peoria, IL)

    1993-11-30T23:59:59.000Z

    An improved gasifier adapted for gasifying a predetermined charge of non-gaseous fuel into fuel gas. Each charge of non-gaseous fuel, which may have optional conditioning materials added to it, is intermittently fed to a gasifier chamber where each charge is partially burned with high-pressure air supplied thereto. High-pressure and temperature fuel gas is produced which is cleansed prior to passing out of the gasifier chamber. After gasification of the charge of fuel is is ended, the gasifier chamber is vented. The residue of the burned charge in the gasifier chamber is removed, along with the contaminated or reacted conditioning materials, and replaced by a fresh charge. The subject invention provides a feasible way of continuously fueling an internal combustion engine with gasified fuel and is compact enough to be practical for even mobile applications.

  5. Advanced High-Temperature, High-Pressure Transport Reactor Gasification

    SciTech Connect (OSTI)

    Michael Swanson; Daniel Laudal

    2008-03-31T23:59:59.000Z

    The U.S. Department of Energy (DOE) National Energy Technology Laboratory Office of Coal and Environmental Systems has as its mission to develop advanced gasification-based technologies for affordable, efficient, zero-emission power generation. These advanced power systems, which are expected to produce near-zero pollutants, are an integral part of DOE's Vision 21 Program. DOE has also been developing advanced gasification systems that lower the capital and operating costs of producing syngas for chemical production. A transport reactor has shown potential to be a low-cost syngas producer compared to other gasification systems since its high-throughput-per-unit cross-sectional area reduces capital costs. This work directly supports the Power Systems Development Facility utilizing the KBR transport reactor located at the Southern Company Services Wilsonville, Alabama, site. Over 2800 hours of operation on 11 different coals ranging from bituminous to lignite along with a petroleum coke has been completed to date in the pilot-scale transport reactor development unit (TRDU) at the Energy & Environmental Research Center (EERC). The EERC has established an extensive database on the operation of these various fuels in both air-blown and oxygen-blown modes utilizing a pilot-scale transport reactor gasifier. This database has been useful in determining the effectiveness of design changes on an advanced transport reactor gasifier and for determining the performance of various feedstocks in a transport reactor. The effects of different fuel types on both gasifier performance and the operation of the hot-gas filter system have been determined. It has been demonstrated that corrected fuel gas heating values ranging from 90 to 130 Btu/scf have been achieved in air-blown mode, while heating values up to 230 Btu/scf on a dry basis have been achieved in oxygen-blown mode. Carbon conversions up to 95% have also been obtained and are highly dependent on the oxygen-coal ratio. Higher-reactivity (low-rank) coals appear to perform better in a transport reactor than the less reactive bituminous coals. Factors that affect TRDU product gas quality appear to be coal type, temperature, and air/coal ratios. Testing with a higher-ash, high-moisture, low-rank coal from the Red Hills Mine of the Mississippi Lignite Mining Company has recently been completed. Testing with the lignite coal generated a fuel gas with acceptable heating value and a high carbon conversion, although some drying of the high-moisture lignite was required before coal-feeding problems were resolved. No ash deposition or bed material agglomeration issues were encountered with this fuel. In order to better understand the coal devolatilization and cracking chemistry occurring in the riser of the transport reactor, gas and solid sampling directly from the riser and the filter outlet has been accomplished. This was done using a baseline Powder River Basin subbituminous coal from the Peabody Energy North Antelope Rochelle Mine near Gillette, Wyoming.

  6. Devices and process for high-pressure magic angle spinning nuclear magnetic resonance

    DOE Patents [OSTI]

    Hoyt, David W; Sears, Jr., Jesse A; Turcu, Romulus V.F.; Rosso, Kevin M; Hu, Jian Zhi

    2014-04-08T23:59:59.000Z

    A high-pressure magic angle spinning (MAS) rotor is detailed that includes a high-pressure sample cell that maintains high pressures exceeding 150 bar. The sample cell design minimizes pressure losses due to penetration over an extended period of time.

  7. Vapor Transport in Dry Soils

    SciTech Connect (OSTI)

    Gee, Glendon W.; Ward, Anderson L.

    2001-11-16T23:59:59.000Z

    Water-vapor movement in soils is a complex process, controlled by both diffusion and advection and influenced by pressure and thermal gradients acting across tortuous flow paths. Wide-ranging interest in water-vapor transport includes both theoretical and practical aspects. Just how pressure and thermal gradients enhance water-vapor flow is still not completely understood and subject to ongoing research. Practical aspects include dryland farming (surface mulching), water harvesting (aerial wells), fertilizer placement, and migration of contaminants at waste-sites. The following article describes the processes and practical applications of water-vapor transport, with emphasis on unsaturated (dry) soil systems.

  8. Novel Low Cost Organic Vapor Jet Printing of Striped High Efficiency Phosphorescent OLEDs for White Lighting

    SciTech Connect (OSTI)

    Mike Hack

    2008-12-31T23:59:59.000Z

    In this program, Universal Display Corporation and University of Michigan proposed to integrate three innovative concepts to meet the DOE's Solid State Lighting (SSL) goals: (1) high-efficiency phosphorescent organic light emitting device (PHOLED{trademark}) technology, (2) a white lighting design that is based on a series of red, green and blue OLED stripes, and (3) the use of a novel cost-effective, high rate, mask-less deposition process called organic vapor jet printing (OVJP). Our PHOLED technology offers up to four-times higher power efficiency than other OLED approaches for general lighting. We believe that one of the most promising approaches to maximizing the efficiency of OLED lighting sources is to produce stripes of the three primary colors at such a pitch (200-500 {mu}m) that they appear as a uniform white light to an observer greater than 1 meter (m) away from the illumination source. Earlier work from a SBIR Phase 1 entitled 'White Illumination Sources Using Striped Phosphorescent OLEDs' suggests that stripe widths of less than 500 {mu}m appear uniform from a distance of 1m without the need for an external diffuser. In this program, we intend to combine continued advances in this PHOLED technology with the striped RGB lighting design to demonstrate a high-efficiency, white lighting source. Using this background technology, the team has focused on developing and demonstrating the novel cost-effective OVJP process to fabricate these high-efficiency white PHOLED light sources. Because this groundbreaking OVJP process is a direct printing approach that enables the OLED stripes to be printed without a shadow mask, OVJP offers very high material utilization and high throughput without the costs and wastage associated with a shadow mask (i.e. the waste of material that deposits on the shadow mask itself). As a direct printing technique, OVJP also has the potential to offer ultra-high deposition rates (> 1,000 Angstroms/second) for any size or shaped features. As a result, we believe that this work will lead to the development of a cost-effective manufacturing solution to produce very-high efficiency OLEDs. By comparison to more common ink-jet printing (IJP), OVJP can also produce well-defined patterns without the need to pattern the substrate with ink wells or to dry/anneal the ink. In addition, the material set is not limited by viscosity and solvent solubility. During the program we successfully demonstrated a 6-inch x 6-inch PHOLED lighting panel consisting of fine-featured red, green and blue (R-G-B) stripes (1mm width) using an OVJP deposition system that was designed, procured and installed into UDC's cleanroom as part of this program. This project will significantly accelerate the DOE's ability to meet its 2015 DOE SSL targets of 70-150 lumens/Watt and less than $10 per 1,000 lumens for high CRI lighting index (76-90). Coupled with a low cost manufacturing path through OVJP, we expect that this achievement will enable the DOE to achieve its 2015 performance goals by the year 2013, two years ahead of schedule. As shown by the technical work performed under this program, we believe that OVJP is a very promising technology to produce low cost, high efficacy, color tunable light sources. While we have made significant progress to develop OVJP technology and build a pilot line tool to study basic aspects of the technology and demonstrate a lighting panel prototype, further work needs to be performed before its full potential and commercial viability can be fully assessed.

  9. Practical features of illumination with high pressure sodium lamps

    SciTech Connect (OSTI)

    Corth, R.

    1983-06-01T23:59:59.000Z

    A number of concerns raised about the health effects of high pressure sodium lamps (HPS) are discussed. The notion of a ''natural'' human photic environment based on sunlight is disputed. Humans are better adapted to the ''greenish'' spectral composition of forest light than to direct sunlight. It is ironic that the artificial light source which has received the most disapproval, cool white flourescent lamp, has a spectral composition similar to that of forest light. HPS is also available in a full range of colors. Some successful examples of HPS--from North Division High School, in Milwaukee, Wisconsin, to museum exhibits at National Geographic in Washington--are listed.

  10. Optical characterization of InN layers grown by high-pressure chemical vapor deposition

    E-Print Network [OSTI]

    Nabben, Reinhard

    and optical properties of InN films grown on sapphire and GaN/sapphire templates. Results obtained from Raman analyzed in this contribution were grown on GaN/sapphire and sapphire 0001 substrates by HPCVD, utilizing to optical absorption edge estimates obtained from optical transmission spectra analysis. The analysis shows

  11. HIGH PRESSURE VAPOR TRANSPORT OF ZnGeP 2 : II. THREEDIMENSIONAL SIMULATION OF GASDYNAMICS UNDER

    E-Print Network [OSTI]

    the laser damage threshold of ZnGeP 2 non­linear optical devices that are built with bulk single crystals in HPVT crystal growth. Introduction Non­linear optical interactions in birefringent materials find laser) radiation. Typically, these materials have been processed using bulk crystal growth techniques

  12. High pressure generation by hot electrons driven ablation

    SciTech Connect (OSTI)

    Piriz, A. R. [E.T.S.I. Industriales, CYTEMA, and Instituto de Investigaciones Energéticas, Universidad de Castilla-La Mancha, 13071 Ciudad Real (Spain)] [E.T.S.I. Industriales, CYTEMA, and Instituto de Investigaciones Energéticas, Universidad de Castilla-La Mancha, 13071 Ciudad Real (Spain); Piriz, S. A. [Facultad de Ciencias Físicas, Universidad Complutense de Madrid, 28040 Madrid (Spain)] [Facultad de Ciencias Físicas, Universidad Complutense de Madrid, 28040 Madrid (Spain); Tahir, N. A. [GSI Helmholtzzentrum für Schwerionenforschung, Planckstrasse 1, 64291 Darmstadt (Germany)] [GSI Helmholtzzentrum für Schwerionenforschung, Planckstrasse 1, 64291 Darmstadt (Germany)

    2013-11-15T23:59:59.000Z

    A previous model [Piriz et al. Phys. Plasmas 19, 122705 (2012)] for the ablation driven by the hot electrons generated in collisionless laser-plasma interactions in the framework of shock ignition is revisited. The impact of recent results indicating that for a laser wavelength ? = 0.35 ?m the hot electron temperature ?{sub H} would be independent of the laser intensity I, on the resulting ablation pressure is considered. In comparison with the case when the scaling law ?{sub H}?(I?{sup 2}){sup 1/3} is assumed, the generation of the high pressures needed for driving the ignitor shock may be more demanding. Intensities above 10{sup 17} W/cm{sup 2} would be required for ?{sub H}=25?30 keV.

  13. High pressure behavior of otavite (CdCo3)

    SciTech Connect (OSTI)

    Minch, R.; Ehm, L.; Seoung, D.H.; Winkler, B.; Knorr, K.; Peters, L.; Borkowski, L.A.; Parise, J.B.; Lee, Y.; Dubrovinsky, L.; Depmeier, W.

    2010-08-24T23:59:59.000Z

    The high-pressure, room temperature behavior of otavite (CdCO{sub 3}) was investigated by angle-dispersive synchrotron radiation powder diffraction up to 40 GPa, Raman spectroscopy up to 23 GPa and quantum mechanical calculations based on density functional theory. The calcite-type structure of CdCO{sub 3} is stable up to at least {approx}19 GPa as shown by Raman spectroscopy. The compression mechanism was obtained from structure refinements against the diffraction data. The quantum mechanical calculations propose a calcite-aragonite phase transition to occur at about 30 GPa. The existence of a pressure-induced phase transition is supported by the Raman and diffraction experiments. Evidence for the transformation is given by broadening of X-ray reflections and external Raman bands starting from about 19 GPa in both experiments.

  14. Synthesis of high-quality monolayer and bilayer graphene on copper using chemical vapor deposition

    E-Print Network [OSTI]

    exfoliation of graphite [1], sublimation of epitaxial SiC [4], and catalyst-assisted chemical vapor deposition (CVD) [5­9]. However, mechanical exfoliation of graphite can only supply small-size graphene (see Fig than that of graphene obtained via exfoli- ation of graphite as summarized in Fig. 1. While many

  15. Optical coatings of variable refractive index and high laser-resistance from physical-vapor-deposited perfluorinated amorphous polymer

    DOE Patents [OSTI]

    Chow, R.; Loomis, G.E.; Thomas, I.M.

    1999-03-16T23:59:59.000Z

    Variable index optical single-layers, optical multilayer, and laser-resistant coatings were made from a perfluorinated amorphous polymer material by physical vapor deposition. This was accomplished by physically vapor depositing a polymer material, such as bulk Teflon AF2400, for example, to form thin layers that have a very low refractive index (ca. 1.10--1.31) and are highly transparent from the ultra-violet through the near infrared regime, and maintain the low refractive index of the bulk material. The refractive index can be varied by simply varying one process parameter, either the deposition rate or the substrate temperature. The thus forming coatings may be utilized in anti-reflectors and graded anti-reflection coatings, as well as in optical layers for laser-resistant coatings at optical wavelengths of less than about 2000 nm. 2 figs.

  16. Optical coatings of variable refractive index and high laser-resistance from physical-vapor-deposited perfluorinated amorphous polymer

    DOE Patents [OSTI]

    Chow, Robert (Livermore, CA); Loomis, Gary E. (Livermore, CA); Thomas, Ian M. (Livermore, CA)

    1999-01-01T23:59:59.000Z

    Variable index optical single-layers, optical multilayer, and laser-resistant coatings were made from a perfluorinated amorphous polymer material by physical vapor deposition. This was accomplished by physically vapor depositing a polymer material, such as bulk Teflon AF2400, for example, to form thin layers that have a very low refractive index (.about.1.10-1.31) and are highly transparent from the ultra-violet through the near infrared regime, and maintain the low refractive index of the bulk material. The refractive index can be varied by simply varying one process parameter, either the deposition rate or the substrate temperature. The thus forming coatings may be utilized in anti-reflectors and graded anti-reflection coatings, as well as in optical layers for laser-resistant coatings at optical wavelengths of less than about 2000 nm.

  17. FRICTION FACTOR IN HIGH PRESSURE NATURAL GAS PIPELINES FROM ROUGHNESS MEASUREMENTS

    E-Print Network [OSTI]

    Gudmundsson, Jon Steinar

    FRICTION FACTOR IN HIGH PRESSURE NATURAL GAS PIPELINES FROM ROUGHNESS MEASUREMENTS DETERMINATION DU and Technology, Norway ABSTRACT Pressure drop experiments on natural gas flow at 80 to 120 bar pressure and high of natural gas at typical operating pressures (100-180 bar). At such Reynolds numbers the classical Colebrook

  18. Dislocations and Plasticity in bcc Transition Metals at High Pressure

    SciTech Connect (OSTI)

    Yang, L H; Tang, M; Moriarty, J A

    2009-01-23T23:59:59.000Z

    Using first-principles electronic structure calculations, quantum-based atomistic simulations and atomistically informed dislocation dynamics (DD) simulations, we have studied individual dislocation behavior and the multiscale modeling of single-crystal plasticity in the prototype bcc transition metals Ta, Mo and V under both ambient and high pressure conditions. The primary focus in this work is on the pressure-dependent structure, mobility and interaction of a/2<111> screw dislocations, which dominate the plastic deformation properties of these materials. At the electronic scale, first-principles calculations of elasticity, ideal strength and generalized stacking fault energy surfaces have been used to validate quantum-based multi-ion interatomic potentials. At the atomistic scale, these potentials have been used in flexible Green's function boundary condition simulations to study the core structure, Peierls stress {tau}{sub P}, thermally activated kink-pair formation and mobility below {tau}{sub P}, and phonon-drag mobility above {tau}{sub P}. These results have then been distilled into analytic velocity laws and used directly in predictive microscale DD simulations of flow stress and resolved yield stress over wide ranges of pressure, temperature and strain rate.

  19. Low-Cost High-Pressure Hydrogen Generator

    SciTech Connect (OSTI)

    Cropley, Cecelia C.; Norman, Timothy J.

    2008-04-02T23:59:59.000Z

    Electrolysis of water, particularly in conjunction with renewable energy sources, is potentially a cost-effective and environmentally friendly method of producing hydrogen at dispersed forecourt sites, such as automotive fueling stations. The primary feedstock for an electrolyzer is electricity, which could be produced by renewable sources such as wind or solar that do not produce carbon dioxide or other greenhouse gas emissions. However, state-of-the-art electrolyzer systems are not economically competitive for forecourt hydrogen production due to their high capital and operating costs, particularly the cost of the electricity used by the electrolyzer stack. In this project, Giner Electrochemical Systems, LLC (GES) developed a low cost, high efficiency proton-exchange membrane (PEM) electrolysis system for hydrogen production at moderate pressure (300 to 400 psig). The electrolyzer stack operates at differential pressure, with hydrogen produced at moderate pressure while oxygen is evolved at near-atmospheric pressure, reducing the cost of the water feed and oxygen handling subsystems. The project included basic research on catalysts and membranes to improve the efficiency of the electrolysis reaction as well as development of advanced materials and component fabrication methods to reduce the capital cost of the electrolyzer stack and system. The project culminated in delivery of a prototype electrolyzer module to the National Renewable Energy Laboratory for testing at the National Wind Technology Center. Electrolysis cell efficiency of 72% (based on the lower heating value of hydrogen) was demonstrated using an advanced high-strength membrane developed in this project. This membrane would enable the electrolyzer system to exceed the DOE 2012 efficiency target of 69%. GES significantly reduced the capital cost of a PEM electrolyzer stack through development of low cost components and fabrication methods, including a 60% reduction in stack parts count. Economic analysis indicates that hydrogen could be produced for $3.79 per gge at an electricity cost of $0.05/kWh by the lower-cost PEM electrolyzer developed in this project, assuming high-volume production of large-scale electrolyzer systems.

  20. System Study: High-Pressure Coolant Injection 1998-2012

    SciTech Connect (OSTI)

    T. E. Wierman

    2013-10-01T23:59:59.000Z

    This report presents an unreliability evaluation of the high-pressure coolant injection system (HPCI) at 69 U.S. commercial nuclear power plants. Demand, run hours, and failure data from fiscal year 1998 through 2012 for selected components were obtained from the Equipment Performance and Information Exchange (EPIX). The unreliability results are trended for the most recent 10 year period while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the HPCI results.

  1. System Study: High-Pressure Core Spray 1998–2012

    SciTech Connect (OSTI)

    T. E. Wierman

    2013-10-01T23:59:59.000Z

    This report presents an unreliability evaluation of the high-pressure core spray (HPCS) at 8 U.S. commercial boiling water reactors. Demand, run hours, and failure data from fiscal year 1998 through 2012 for selected components were obtained from the Equipment Performance and Information Exchange (EPIX). The unreliability results are trended for the most recent 10 year period while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the HPCS results.

  2. System Study: High-Pressure Safety Injection 1998–2012

    SciTech Connect (OSTI)

    T. E. Wierman

    2013-10-01T23:59:59.000Z

    This report presents an unreliability evaluation of the high-pressure safety injection system (HPSI) at 69 U.S. commercial nuclear power plants. Demand, run hours, and failure data from fiscal year 1998 through 2012 for selected components were obtained from the Equipment Performance and Information Exchange (EPIX). The unreliability results are trended for the most recent 10 year period while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the HPSI results.

  3. High-Pressure MOF Research Yields Structural Insights

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Science (SC) EnvironmentalGyroSolé(tm) Harmonicbet WhenHiggsmiddlewareHigh-Pressure MOF

  4. Working with SRNL - Our Facilities- High Pressure Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What'sis Taking Over OurThe Iron SpinPrincetonUsingWhat is abigpresentedMetal HydrideHigh Pressure

  5. High-Pressure Melt Streaming (HIPS) program plan

    SciTech Connect (OSTI)

    Tarbell, W.; Brockmann, J.; Pilch, M.

    1984-08-01T23:59:59.000Z

    The Zion Probabilistic Safety Study (ZPSS) envisions accident sequences that could lead to failure of the reactor vessel while the primary system is pressurized. The resulting ejection of molten core material into the reactor cavity followed by the blowdown of steam and hydrogen is shown to cause the debris to enter into the containment region. The High Pressure Melt Streaming (HIPS) program has been developed to provide an experimental and analytical investigation of the scenario described above. One-tenth linear scale models of the Zion cavity region will be used to investigate the debris dispersal phenomena. Smaller-scale experiments (SPIT-tests) are also used to study high-velocity jets, jet-water interactions, and 1/20th scale cavity geometries. Both matrices are developed using a factorial design approach. The document describes certain aspects of the ZPSS ex-vessel phenomena, the experimental matrices, test equipment, and instrumentation, and the program's analytical efforts. Preliminary data from SPIT testing are included.

  6. Acceptance test procedure for High Pressure Water Jet System

    SciTech Connect (OSTI)

    Crystal, J.B.

    1995-05-30T23:59:59.000Z

    The overall objective of the acceptance test is to demonstrate a combined system. This includes associated tools and equipment necessary to perform cleaning in the 105 K East Basin (KE) for achieving optimum reduction in the level of contamination/dose rate on canisters prior to removal from the KE Basin and subsequent packaging for disposal. Acceptance tests shall include necessary hardware to achieve acceptance of the cleaning phase of canisters. This acceptance test procedure will define the acceptance testing criteria of the high pressure water jet cleaning fixture. The focus of this procedure will be to provide guidelines and instructions to control, evaluate and document the acceptance testing for cleaning effectiveness and method(s) of removing the contaminated surface layer from the canister presently identified in KE Basin. Additionally, the desired result of the acceptance test will be to deliver to K Basins a thoroughly tested and proven system for underwater decontamination and dose reduction. This report discusses the acceptance test procedure for the High Pressure Water Jet.

  7. Very low pressure high power impulse triggered magnetron sputtering

    DOE Patents [OSTI]

    Anders, Andre; Andersson, Joakim

    2013-10-29T23:59:59.000Z

    A method and apparatus are described for very low pressure high powered magnetron sputtering of a coating onto a substrate. By the method of this invention, both substrate and coating target material are placed into an evacuable chamber, and the chamber pumped to vacuum. Thereafter a series of high impulse voltage pulses are applied to the target. Nearly simultaneously with each pulse, in one embodiment, a small cathodic arc source of the same material as the target is pulsed, triggering a plasma plume proximate to the surface of the target to thereby initiate the magnetron sputtering process. In another embodiment the plasma plume is generated using a pulsed laser aimed to strike an ablation target material positioned near the magnetron target surface.

  8. Comparison of diesel spray combustion in different high-temperature, high-pressure facilities.

    SciTech Connect (OSTI)

    Christiansen, Caspar (Technical University of Denmark); Hermant, Laurent (IFP); Malbec, Louis-Marie (IFP); Bruneaux, Gilles (IFP); Genzale, Caroline L.; Pickett, Lyle M.; Schramm, Jesper (Technical University of Denmark)

    2010-05-01T23:59:59.000Z

    Diesel spray experiments at controlled high-temperature and high-pressure conditions offer the potential for an improved understanding of diesel combustion, and for the development of more accurate CFD models that will ultimately be used to improve engine design. Several spray chamber facilities capable of high-temperature, high-pressure conditions typical of engine combustion have been developed, but uncertainties about their operation exist because of the uniqueness of each facility. For the IMEM meeting, we describe results from comparative studies using constant-volume vessels at Sandia National Laboratories and IFP. Targeting the same ambient gas conditions (900 K, 60 bar, 22.8 kg/m{sup 3}, 15% oxygen) and sharing the same injector (common rail, 1500 bar, KS1.5/86 nozzle, 0.090 mm orifice diameter, n-dodecane, 363 K), we describe detailed measurements of the temperature and pressure boundary conditions at each facility, followed by observations of spray penetration, ignition, and combustion using high-speed imaging. Performing experiments at the same high-temperature, high-pressure operating conditions is an objective of the Engine Combustion Network (http://www.ca.sandia.gov/ECN/), which seeks to leverage the research capabilities and advanced diagnostics of all participants in the ECN. We expect that this effort will generate a high-quality dataset to be used for advanced computational model development at engine conditions.

  9. High- and low-temperature-stable thermite composition for producing high-pressure, high-velocity gases

    DOE Patents [OSTI]

    Halcomb, Danny L. (Camden, OH); Mohler, Jonathan H. (Spring Valley, OH)

    1990-10-16T23:59:59.000Z

    A high- and low-temperature-stable thermite composition for producing high-pressure and high-velocity gases comprises an oxidizable metal, an oxidizing reagent, and a high-temperature-stable gas-producing additive selected from the group consisting of metal carbides and metal nitrides.

  10. High-pressure coal fuel processor development. Final report

    SciTech Connect (OSTI)

    Greenhalgh, M.L. [Caterpillar, Inc., Peoria, IL (United States)

    1992-12-01T23:59:59.000Z

    Caterpillar shares DOE/METC interest in demonstrating the technology required to displace petroleum-based engine fuels with various forms of low cost coal. Current DOE/METC programs on mild gasification and coal-water-slurries are addressing two approaches to this end. Engine and fuel processor system concept studies by Caterpillar have identified a third, potentially promising, option. This option includes high-pressure fuel processing of run-of-the-mine coal and direct injection of the resulting low-Btu gas stream into an ignition assisted, high compression ratio diesel engine. The compactness and predicted efficiency of the system make it suitable for application to line-haul railroad locomotives. Two overall conclusions resulted from Task 1. First direct injected, ignition assisted Diesel cycle engine combustion systems can be suitably modified to efficiently utilize low-Btu gas fuels. Second, high pressure gasification of selected run-of-the-mine coals in batch-loaded fuel processors is feasible. These two findings, taken together, significantly reduce the perceived technical risk associated with the further development of the proposed coal gas fueled Diesel cycle power plant concept. The significant conclusions from Task 2 were: An engine concept, derived from a Caterpillar 3600 series engine, and a fuel processor concept, based on scaling up a removable-canister configuration from the test rig, appear feasible; and although the results of this concept study are encouraging, further, full-scale component research and development are required before attempting a full-scale integrated system demonstration effort.

  11. Pressure Resistance Welding of High Temperature Metallic Materials

    SciTech Connect (OSTI)

    N. Jerred; L. Zirker; I. Charit; J. Cole; M. Frary; D. Butt; M. Meyer; K. L. Murty

    2010-10-01T23:59:59.000Z

    Pressure Resistance Welding (PRW) is a solid state joining process used for various high temperature metallic materials (Oxide dispersion strengthened alloys of MA957, MA754; martensitic alloy HT-9, tungsten etc.) for advanced nuclear reactor applications. A new PRW machine has been installed at the Center for Advanced Energy Studies (CAES) in Idaho Falls for conducting joining research for nuclear applications. The key emphasis has been on understanding processing-microstructure-property relationships. Initial studies have shown that sound joints can be made between dissimilar materials such as MA957 alloy cladding tubes and HT-9 end plugs, and MA754 and HT-9 coupons. Limited burst testing of MA957/HT-9 joints carried out at various pressures up to 400oC has shown encouraging results in that the joint regions do not develop any cracking. Similar joint strength observations have also been made by performing simple bend tests. Detailed microstructural studies using SEM/EBSD tools and fatigue crack growth studies of MA754/HT-9 joints are ongoing.

  12. TENSILE TESTING OF CARBON STEEL IN HIGH PRESSURE HYDROGEN

    SciTech Connect (OSTI)

    Duncan, A; Thad Adams, T; Ps Lam, P

    2007-05-02T23:59:59.000Z

    An infrastructure of new and existing pipelines and systems will be required to carry and to deliver hydrogen as an alternative energy source under the hydrogen economy. Carbon and low alloy steels of moderate strength are currently used in hydrogen delivery systems as well as in the existing natural gas systems. It is critical to understand the material response of these standard pipeline materials when they are subjected to pressurized hydrogen environments. The methods and results from a testing program to quantify hydrogen effects on mechanical properties of carbon steel pipeline and pipeline weld materials are provided. Tensile properties of one type of steel (A106 Grade B) in base metal, welded and heat affected zone conditions were tested at room temperature in air and high pressure (10.34 MPa or 1500 psig) hydrogen. A general reduction in the materials ability to plastically deform was noted in this material when specimens were tested in hydrogen. Furthermore, the primary mode of fracture was changed from ductile rupture in air to cleavage with secondary tearing in hydrogen. The mechanical test results will be applied in future analyses to evaluate service life of the pipelines. The results are also envisioned to be part of the bases for construction codes and structural integrity demonstrations for hydrogen service pipeline and vessels.

  13. GFOC Project results: High Temperature / High Pressure, Hydrogen Tolerant Optical Fiber

    SciTech Connect (OSTI)

    E. Burov; A. Pastouret; E. Aldea; B. Overton; F. Gooijer; A. Bergonzo

    2012-02-12T23:59:59.000Z

    Tests results are given for exposure of multimode optical fiber to high temperatures (300 deg. C) and high partial pressure (15 bar) hydrogen. These results demonstrate that fluorine down doped optical fibers are much more hydrogen tolerant than traditional germanium doped multimode optical fibers. Also demonstrated is the similar hydrogen tolerance of carbon coated and non-carbon coated fibers. Model for reversible H2 impact in fiber versus T{sup o}C and H2 pressure is given. These results have significant impact for the longevity of use for distributed temperature sensing applications in harsh environments such as geothermal wells.

  14. anomalous high-pressure behavior: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    than recently predicted. McMahon, Jeffrey M 2011-01-01 105 Selection of High Strength Encapsulant for MEMS Devices Undergoing High Pressure Packaging CERN Preprints Summary:...

  15. Vacuum surface flashover and high pressure gas streamers

    SciTech Connect (OSTI)

    Elizondo, J.M.; Krogh, M.L.; Smith, D.; Stolz, D.; Wright, S.N. [Allied-Signal Aerospace Co., Kansas City, MO (United States). Kansas City Div.; Sampayan, S.E.; Caporaso, G.J.; Vitello, P.; Tishchenko, N. [Lawrence Livermore National Lab., CA (United States)

    1997-07-01T23:59:59.000Z

    Pre-breakdown current traces obtained during high pressure gas breakdown and vacuum surface flashover show similar signatures. The initial pre-breakdown current spike, a flat constant current phase, and the breakdown phase with voltage collapse and current surge differ mostly in magnitude. Given these similarities, a model, consisting of the initial current spike corresponding to a fast precursor streamer (ionization wave led by a photoionizing front), the flat current stage as the heating or glow phase, and the terminal avalanche and gap closure, is applied to vacuum surface flashover. A simple analytical approximation based on the resistivity changes induced in the vacuum and dielectric surface is presented. The approximation yields an excellent fit to pre-breakdown time delay vs applied field for previously published experimental data. A detailed kinetics model that includes surface and gas contributions is being developed based in the initial approximation.

  16. Dynamic behavior of an aggregate material at simultaneous high pressure and strain rate: SHPB triaxial tests

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 Dynamic behavior of an aggregate material at simultaneous high pressure and strain rate: SHPB Low velocity impacts on energetic materials induce plastic deformations and sliding friction which can pressure and high strain rate). Thus, a technique based on the Split Hopkinson Pressure Bars system

  17. Equations of state of ice VI and ice VII at high pressure and high temperature

    SciTech Connect (OSTI)

    Bezacier, Lucile; Hanfland, Michael [European Synchrotron Radiation Facility, 6 rue Jules Horowitz, 38000 Grenoble (France); Journaux, Baptiste; Perrillat, Jean-Philippe; Cardon, Hervé; Daniel, Isabelle [Laboratoire de Géologie de Lyon, UMR 5276 CNRS, Ecole Normale Supérieure de Lyon – Université Claude Bernard Lyon 1, 2 rue Raphael Dubois, 69622 Villeurbanne Cedex (France)

    2014-09-14T23:59:59.000Z

    High-pressure H{sub 2}O polymorphs among which ice VI and ice VII are abundant in the interiors of large icy satellites and exo-planets. Knowledge of the elastic properties of these pure H{sub 2}O ices at high-temperature and high-pressure is thus crucial to decipher the internal structure of icy bodies. In this study we assess for the first time the pressure-volume-temperature (PVT) relations of both polycrystalline pure ice VI and ice VII at high pressures and temperatures from 1 to 9 GPa and 300 to 450 K, respectively, by using in situ synchrotron X-ray diffraction. The PVT data are adjusted to a second-order Birch-Murnaghan equation of state and give V{sub 0} = 14.17(2) cm{sup 3}?mol{sup ?1}, K{sub 0} = 14.05(23) GPa, and ?{sub 0} = 14.6(14) × 10{sup ?5} K{sup ?1} for ice VI and V{sub 0} = 12.49(1) cm{sup 3}?mol{sup ?1}, K{sub 0} = 20.15(16) GPa, and ?{sub 0} = 11.6(5) × 10{sup ?5} K{sup ?1} for ice VII.

  18. High-pressure cell for neutron diffraction with in situ pressure control at cryogenic temperatures

    SciTech Connect (OSTI)

    Jacobsen, Matthew K.; Ridley, Christopher J.; Bocian, Artur; Kamenev, Konstantin V., E-mail: k.kamenev@ed.ac.uk [School of Engineering and CSEC, University of Edinburgh, Edinburgh (United Kingdom); Kirichek, Oleg; Manuel, Pascal; Khalyavin, Dmitry [ISIS, Rutherford Appleton Laboratory, Harwell Oxford (United Kingdom)] [ISIS, Rutherford Appleton Laboratory, Harwell Oxford (United Kingdom); Azuma, Masaki [Materials and Structures Laboratory, Tokyo Institute of Technology, Tokyo (Japan)] [Materials and Structures Laboratory, Tokyo Institute of Technology, Tokyo (Japan); Attfield, J. Paul [School of Chemistry and CSEC, University of Edinburgh, Edinburgh (United Kingdom)] [School of Chemistry and CSEC, University of Edinburgh, Edinburgh (United Kingdom)

    2014-04-15T23:59:59.000Z

    Pressure generation at cryogenic temperatures presents a problem for a wide array of experimental techniques, particularly neutron studies due to the volume of sample required. We present a novel, compact pressure cell with a large sample volume in which load is generated by a bellow. Using a supply of helium gas up to a pressure of 350 bar, a load of up to 78 kN is generated with leak-free operation. In addition, special fiber ports added to the cryogenic center stick allow for in situ pressure determination using the ruby pressure standard. Mechanical stability was assessed using finite element analysis and the dimensions of the cell have been optimized for use with standard cryogenic equipment. Load testing and on-line experiments using NaCl and BiNiO{sub 3} have been done at the WISH instrument of the ISIS pulsed neutron source to verify performance.

  19. High Performance Fuel Desing for Next Generation Pressurized Water Reactors

    SciTech Connect (OSTI)

    Mujid S. Kazimi; Pavel Hejzlar

    2006-01-31T23:59:59.000Z

    The use of internally and externally cooled annular fule rods for high power density Pressurized Water Reactors is assessed. The assessment included steady state and transient thermal conditions, neutronic and fuel management requirements, mechanical vibration issues, fuel performance issues, fuel fabrication methods and econmic assessment. The investigation was donducted by a team from MIT, Westinghouse, Gamma Engineering, Framatome ANP, and AECL. The analyses led to the conclusion that raising the power density by 50% may be possible with this advanced fuel. Even at the 150% power level, the fuel temperature would be a few hundred degrees lower than the current fuel temperatre. Significant economic and safety advantages can be obtained by using this fuel in new reactors. Switching to this type of fuel for existing reactors would yield safety advantages, but the economic return is dependent on the duration of plant shutdown to accommodate higher power production. The main feasiblity issue for the high power performance appears to be the potential for uneven splitting of heat flux between the inner and outer fuel surfaces due to premature closure of the outer fuel-cladding gap. This could be overcome by using a very narrow gap for the inner fuel surface and/or the spraying of a crushable zirconium oxide film at the fuel pellet outer surface. An alternative fuel manufacturing approach using vobropacking was also investigated but appears to yield lower than desirable fuel density.

  20. High Temperature Electrolysis Pressurized Experiment Design, Operation, and Results

    SciTech Connect (OSTI)

    J.E. O'Brien; X. Zhang; G.K. Housley; K. DeWall; L. Moore-McAteer

    2012-09-01T23:59:59.000Z

    A new facility has been developed at the Idaho National Laboratory for pressurized testing of solid oxide electrolysis stacks. Pressurized operation is envisioned for large-scale hydrogen production plants, yielding higher overall efficiencies when the hydrogen product is to be delivered at elevated pressure for tank storage or pipelines. Pressurized operation also supports higher mass flow rates of the process gases with smaller components. The test stand can accommodate planar cells with dimensions up to 8.5 cm x 8.5 cm and stacks of up to 25 cells. It is also suitable for testing other cell and stack geometries including tubular cells. The pressure boundary for these tests is a water-cooled spool-piece pressure vessel designed for operation up to 5 MPa. Pressurized operation of a ten-cell internally manifolded solid oxide electrolysis stack has been successfully demonstrated up 1.5 MPa. The stack is internally manifolded and operates in cross-flow with an inverted-U flow pattern. Feed-throughs for gas inlets/outlets, power, and instrumentation are all located in the bottom flange. The entire spool piece, with the exception of the bottom flange, can be lifted to allow access to the internal furnace and test fixture. Lifting is accomplished with a motorized threaded drive mechanism attached to a rigid structural frame. Stack mechanical compression is accomplished using springs that are located inside of the pressure boundary, but outside of the hot zone. Initial stack heatup and performance characterization occurs at ambient pressure followed by lowering and sealing of the pressure vessel and subsequent pressurization. Pressure equalization between the anode and cathode sides of the cells and the stack surroundings is ensured by combining all of the process gases downstream of the stack. Steady pressure is maintained by means of a backpressure regulator and a digital pressure controller. A full description of the pressurized test apparatus is provided in this report. Results of initial testing showed the expected increase in open-cell voltage associated with elevated pressure. However, stack performance in terms of area-specific resistance was enhanced at elevated pressure due to better gas diffusion through the porous electrodes of the cells. Some issues such as cracked cells and seals were encountered during testing. Full resolution of these issues will require additional testing to identify the optimum test configurations and protocols.

  1. An apparatus for studying scintillator properties at high isostatic pressures

    SciTech Connect (OSTI)

    Gaume, R. M. [College of Optics and Photonics (CREOL) and NanoScience Technology Center, University of Central Florida, Orlando, Florida 32816 (United States); Lam, S.; Gascon, M.; Feigelson, R. S. [Department of Materials Science and Engineering, Stanford University, Stanford, California 94305 (United States); Setyawan, W. [Pacific Northwest National Laboratory, Richland, Washington 99352 (United States); Curtarolo, S. [Department of Mechanical Engineering and Materials Science, Duke University, Durham, North Carolina 27708 (United States)

    2013-01-15T23:59:59.000Z

    We describe the design and operation of a unique hydraulic press for the study of scintillator materials under isostatic pressure. This press, capable of developing a pressure of a gigapascal, consists of a large sample chamber pressurized by a two-stage hydraulic amplifier. The optical detection of the scintillation light emitted by the sample is performed, through a large aperture optical port, by a photodetector located outside the pressure vessel. In addition to providing essential pressure-dependent studies on the emission characteristics of radioluminescent materials, this apparatus is being developed to elucidate the mechanisms behind the recently observed dependency of light-yield nonproportionality on electronic band structure. The variation of the light output of a Tl:CsI crystal under 511-keV gamma excitation and hydrostatic pressure is given as an example.

  2. Plasma etching of cavities into diamond anvils for experiments at high pressures and high temperatures

    SciTech Connect (OSTI)

    Weir, S.T.; Cynn, H.; Falabella, S.; Evans, W.J.; Aracne-Ruddle, C.; Farber, D.; Vohra, Y.K. (LLNL); (UAB)

    2012-10-23T23:59:59.000Z

    We describe a method for precisely etching small cavities into the culets of diamond anvils for the purpose of providing thermal insulation for samples in experiments at high pressures and high temperatures. The cavities were fabricated using highly directional oxygen plasma to reactively etch into the diamond surface. The lateral extent of the etch was precisely controlled to micron accuracy by etching the diamond through a lithographically fabricated tungsten mask. The performance of the etched cavities in high-temperature experiments in which the samples were either laser heated or electrically heated is discussed.

  3. High voltage ignition of high pressure microwave powered UV light sources

    SciTech Connect (OSTI)

    Frank, J.D.; Cekic, M.; Wood, C.H. [Fusion U.V. Curing Systems Corp., Gaithersburg, MD (United States)

    1997-12-31T23:59:59.000Z

    Industrial microwave powered (electrodeless) light sources have been limited to quiescent pressures of {approximately}300 Torr of buffer gas and metal-halide fills. The predominant reason for such restrictions has been the inability to microwave ignite the plasma due to the collisionality of higher pressure fills and/or the electronegativity of halide bulb chemistries. Commercially interesting bulb fills require electric fields for ionization that are often large multiples of the breakdown voltage for air. Many auxiliary ignition methods are evaluated for efficiency and practicality before the choice of a high-voltage system with a retractable external electrode. The scheme utilizes a high voltage pulse power supply and a novel field emission source. Acting together they create localized condition of pressure reduction and high free electron density. This allows the normal microwave fields to drive this small region into avalanche, ignite the bulb, and heat the plasma to its operating point (T{sub e} {approx} 0.5 eV). This process is currently being used in a new generation of lamps, which are using multi-atmospheric excimer laser chemistries and pressure and constituent enhanced metal-halide systems. At the present time, production prototypes produce over 900 W of radiation in a 30 nm band, centered at 308 nm. Similarly, these prototypes when loaded with metal-halide bulb fills produce over 1 kW of radiation in 30 nm wide bands, centered about the wavelength of interest.

  4. Bonfire Tests of High Pressure Hydrogen Storage Tanks

    Broader source: Energy.gov [DOE]

    These slides were presented at the International Hydrogen Fuel and Pressure Vessel Forum on September 27 – 29, 2010, in Beijing, China.

  5. Experiment Hazard Class 5.3 High Pressure Vessels

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    stresses calculated using ASME Code Case 2286 July 17 1998. Verify that pressure relief devices have ASME "UV" certification or documentation of operability tests demonstrating...

  6. Technical and economic evaluation of ten high temperature, high pressure particulate cleanup systems for pressurized fluidized bed combustion

    SciTech Connect (OSTI)

    Rubow, L.N.; Borden, M.; Buchanan, T.L.; Cramp, J.A.C.; Fischer, W.H.; Klett, M.G.; Maruvada, S.M.; Nelson, E.T.; Weinstein, R.E.; Zaharchuk, R.

    1984-07-01T23:59:59.000Z

    The objective of this analysis was to provide a technical and economic evaluation of the ten high temperature, high pressure (HTHP) systems for the purpose of prioritizing them according to performance, cost, and general viability of achieving commercial status. The scope primarily included reviewing/normalizing test experience to date, normalizing commercial designs, developing normalized capital and operating costs for each system, performing trade-off studies, and performing an evaluation utilizing in-house and outside inputs. The HTHP particulate cleanup system must be capable of the same stringent operating requirements as a conventional system, except it must do so at HTHP conditions. Utilities will demand nearly the same reliability as found in conventional equipment. Regarding particulate cleanup, the system must meet NSPS requirements at the stack, and also meet turbine inlet requirements. The ten devices evaluated were: Electrostatic Precipitator - Cottrell Environmental Sciences (CES); Ceramic Felt Filter - Acurex Corporation; Ceramic Cross Flow Filter - Westinghouse; Shallow Static Granular Bed Filter - Ducon/Westinghouse; Electrostatic Granular Bed Filter - General Electric (GE); Moving Granular Bed Filter - Combustion Power Company (CPC); Dry Plate Scrubber - Air Pollution Technology (APT); Magnetic Granular Bed Filter - Exxon; Electrocyclone - General Electric; and Acoustic Agglomerator - Aerojet/Pennsylvania State University (PSU). The test data for the ten devices were normalized to standard conditions with a reference inlet particle loading and size distribution. The purpose of system design normalization is to provide, for each of the HTHP concepts, a scaled-up commercial design which reflects a consistent design approach. 104 figures, 136 tables.

  7. Pulsed laser kinetic studies of liquids under high pressure

    SciTech Connect (OSTI)

    Eyring, E.M.

    1993-06-21T23:59:59.000Z

    Experiments have been developed for measuring the rates of chemical reactions liquids and in supercritical Co[sub 2]. A pulsed (Q-switch) Nd:YAG laser at 355 nm was the pump beam for laser flash photolysis studies of molybdenum and tungsten hexacarbonyls undergoing ligand displacement reactions by bidentate chelating agents such as 2,2[prime]-bipyridine in toluene. Experiments were carried out at 0.1 to 150 MPa. In the case of molybdenum complexes, the reaction mechanism for thermal ring closure is found from activation volumes to change from associative interchange to dissociative interchange as substituents on the 2,2[prime]-bipyridine ligands become bulkier. In a similar study of more rigid, substituted phenanthroline bidentate ligands it was found that substituent bulkiness had little effect on the thermal ring closure mechanism. Similar high pressure flash photolysis experiments with tungsten hexacarbonyl have also been completed. The concentration dependence of the fluorescence and nonradiative decay quantum yields for cresyl violet in several solvent have been reported as well as stability constants for the complexation of lithium ion by four different crown ethers dissolved in a room temperature molten salt.

  8. High Pressure Sensing and Dynamics Using High Speed Fiber Bragg Grating Interrogation Systems

    SciTech Connect (OSTI)

    Rodriguez, G. [LANL; Sandberg, R. L. [LANL; Lalone, B. M. [NSTec; Marshall, B. R. [NSTec; Grover, M. [NSTec; Stevens, G. D. [NSTec; Udd, E. [Columbia Gorge Research

    2014-06-01T23:59:59.000Z

    Fiber Bragg gratings (FBGs) are developing into useful sensing tools for measuring high pressure dynamics in extreme environments under shock loading conditions. Approaches using traditional diode array coupled FBG interrogation systems are often limited to readout speeds in the sub-MHz range. For shock wave physics, required detection speeds approaching 100 MHz are desired. We explore the use of two types of FBG sensing systems that are aimed at applying this technology as embedded high pressure probes for transient shock events. Both approaches measure time resolved spectral shifts in the return light from short (few mm long) uniform FBGs at 1550 nm. In the first approach, we use a fiber coupled spectrometer to demultiplex spectral channels into an array (up to 12) of single element InGaAs photoreceivers. By monitoring the detectors during a shock impact event with high speed recording, we are able to track the pressure induced spectral shifting in FBG down to a time resolution of 20 ns. In the second approach, developed at the Special Technologies Lab, a coherent mode-locked fiber laser is used to illuminate the FBG sensor. After the sensor, wavelength-to-time mapping is accomplished with a chromatic dispersive element, and entire spectra are sampled using a single detector at the modelocked laser repetition rate of 50 MHz. By sampling with a 12 GHz InGaAs detector, direct wavelength mapping in time is recorded, and the pressure induced FBG spectral shift is sampled at 50 MHz. Here, the sensing systems are used to monitor the spectral shifts of FBGs that are immersed into liquid water and shock compressed using explosives. In this configuration, the gratings survive to pressures approaching 50 kbar. We describe both approaches and present the measured spectral shifts from the shock experiments.

  9. Hydride vapor phase epitaxy and characterization of high-quality ScN epilayers

    SciTech Connect (OSTI)

    Oshima, Yuichi, E-mail: OSHIMA.Yuichi@nims.go.jp; Víllora, Encarnación G.; Shimamura, Kiyoshi [Environment and Energy Materials Research Division, National Institute for Materials Science, 1-1 Namiki, Tsukuba, Ibaraki 305-0044 (Japan)

    2014-04-21T23:59:59.000Z

    The heteroepitaxial growth of ScN films was investigated on various substrates by hydride vapor phase epitaxy (HVPE). Single crystalline mirror-like ScN(100) and ScN(110) layers were successfully deposited on r- and m-plane sapphire substrates, respectively. Homogeneous stoichiometric films (N/Sc ratio 1.01?±?0.10) up to 40??m in thickness were deposited. Their mosaicity drastically improved with increasing the film thickness. The band gap was determined by optical methods to be 2.06?eV. Impurity concentrations including H, C, O, Si, and Cl were investigated through energy dispersive X-ray spectrometry and secondary ion mass spectrometry. As a result, it was found that the presence of impurities was efficiently suppressed in comparison with that of HVPE-grown ScN films reported in the past, which was possible thanks to the home-designed corrosion-free HVPE reactor. Room-temperature Hall measurements indicated that the residual free electron concentrations ranged between 10{sup 18}–10{sup 20}?cm{sup ?3}, which was markedly lower than the reported values. The carrier mobility increased monotonically with the decreasing in carrier concentration, achieving the largest value ever reported, 284?cm{sup 2}?V{sup ?1}?s{sup ?1} at n?=?3.7?×?10{sup 18}?cm{sup ?3}.

  10. Size-dependent structure of silver nanoparticles under high pressure

    SciTech Connect (OSTI)

    Koski, Kristie Jo

    2008-12-31T23:59:59.000Z

    Silver noble metal nanoparticles that are<10 nm often possess multiply twinned grains allowing them to adopt shapes and atomic structures not observed in bulk materials. The properties exhibited by particles with multiply twinned polycrystalline structures are often far different from those of single-crystalline particles and from the bulk. I will present experimental evidence that silver nanoparticles<10 nm undergo a reversible structural transformation under hydrostatic pressures up to 10 GPa. Results for nanoparticles in the intermediate size range of 5 to 10 nm suggest a reversible linear pressure-dependent rhombohedral distortion which has not been previously observed in bulk silver. I propose a mechanism for this transitiion that considers the bond-length distribution in idealized multiply twinned icosahedral particles. Results for nanoparticles of 3.9 nm suggest a reversible linear pressure-dependent orthorhombic distortion. This distortion is interpreted in the context of idealized decahedral particles. In addition, given these size-dependent measurements of silver nanoparticle compression with pressure, we have constructed a pressure calibration curve. Encapsulating these silver nanoparticles in hollow metal oxide nanospheres then allows us to measure the pressure inside a nanoshell using x-ray diffraction. We demonstrate the measurement of pressure gradients across nanoshells and show that these nanoshells have maximum resolved shear strengths on the order of 500 MPa to IGPa.

  11. Aerosol source term in high pressure melt ejection

    SciTech Connect (OSTI)

    Brockmann, J.E.; Tarbell, W.W.

    1984-11-01T23:59:59.000Z

    Pressurized ejection of melt from a reactor pressure vessel has been identified as an important element of a severe reactor accident. Copious aerosol production is observed when thermitically generated melts pressurized with nitrogen or carbon dioxide to 1.3 to 17 MPa are ejected into an air atmosphere. Aerosol particle size distributions measured in the tests have modes of about 0.5, 5, and > 10 ..mu..m. Mechanisms leading to formation of these multimodal size distributions are suggested. This aerosol is a potentially important fission product source term that has not been considered in previous severe accident analyses.

  12. High-pressure gasification of Montana subbituminous coal

    SciTech Connect (OSTI)

    Goyal, A.; Bryan, B.; Rehmat, A.

    1991-01-01T23:59:59.000Z

    A data base for the fluidized-bed gasification of different coals at elevated pressures has been developed at the Institute of Gas Technology (IGT) with different ranks of coal at pressures up to 450 psig and at temperatures dictated by the individual coals. Adequate data have been obtained to characterize the effect of pressure on the gasification of Montana Rosebud subbituminous coal and North Dakota lignite. The results obtained with Montana Rosebud subbituminous coal are presented here. This program was funded by the Gas Research Institute. 9 refs., 10 figs., 3 tabs.

  13. High Resolution Additive Patterning of Nanoparticles and Polymers Enabled by Vapor Permeable Polymer Templates

    E-Print Network [OSTI]

    Demko, Michael Thomas

    2012-01-01T23:59:59.000Z

    High Resolution Additive Patterning of Nanoparticles andHigh Resolution Additive Patterning of Nanoparticles andareas, and in a completely additive manner. In this work, a

  14. Microdischarge-assisted ignition of dielectric-barrier high-pressure glow discharges

    E-Print Network [OSTI]

    Raja, Laxminarayan L.

    of an array of microdischarges integrated with one of the DB-HPG electrodes, a substantial reduction of DB­1000 Torr.1,2 Due to high pd pressure-distance val- ues at high pressures, relatively high breakdown of four microdischarges on the bottom electrode-dielectric assembly surface. The up- per electrode

  15. Materials for High-Pressure Fuel Injection Systems

    SciTech Connect (OSTI)

    Blau, P.; Shyam, A.; Hubbard, C.; Howe, J.; Trejo, R.; Yang, N. (Caterpillar, Inc. Technical Center) [Caterpillar, Inc. Technical Center; Pollard, M. (Caterpillar, Inc. Technical Center) [Caterpillar, Inc. Technical Center

    2011-09-30T23:59:59.000Z

    The high-level goal of this multi-year effort was to facilitate the Advanced Combustion Engine goal of 20% improvement (compared to 2009 baseline) of commercial engine efficiency by 2015. A sub-goal is to increase the reliability of diesel fuel injectors by investigating modelbased scenarios that cannot be achieved by empirical, trial and error methodologies alone. During this three-year project, ORNL developed the methodology to evaluate origins and to record the initiation and propagation of fatigue cracks emanating from holes that were electrodischarge machined (EDM), the method used to form spray holes in fuel injector tips. Both x-ray and neutron-based methods for measuring residual stress at four different research facilities were evaluated to determine which, if any, was most applicable to the fuel injector tip geometry. Owing to the shape and small volumes of material involved in the sack area, residual stress data could only be obtained in the walls of the nozzle a few millimeters back from the tip, and there was a hint of only a small compressive stress. This result was consistent with prior studies by Caterpillar. Residual stress studies were suspended after the second year, reserving the possibility of pursuing this in the future, if and when methodology suitable for injector sacks becomes available. The smooth specimen fatigue behavior of current fuel injector steel materials was evaluated and displayed a dual mode initiation behavior. At high stresses, cracks started at machining flaws in the surface; however, below a critical threshold stress of approximately 800 MPa, cracks initiated in the bulk microstructure, below the surface. This suggests that for the next generation for high-pressure fuel injector nozzles, it becomes increasingly important to control the machining and finishing processes, especially if the stress in the tip approaches or exceeds that threshold level. Fatigue tests were also conducted using EDM notches in the gage sections. Compared to the smooth specimens, EDM notching led to a severe reduction in total fatigue life. A reduction in fatigue life of nearly four orders of magnitude can occur at an EDM notch the approximate size of fuel injector spray holes. Consequently, the initiation and propagation behavior of cracks from small spray holes is relevant for generation of design quality data for the next generation diesel fuel injection devices. This is especially true since the current design methodologies usually rely on the less conservative smooth specimen fatigue testing results, and since different materials can have varying levels of notch fatigue resistance.

  16. Effects of arrival rate and gas pressure on the chemical bonding and composition in titanium nitride films prepared on Si(100) substrates by ion beam and vapor deposition

    SciTech Connect (OSTI)

    Matsuoka, M.; Isotani, S.; Mittani, J.C.R.; Chubaci, J.F.D.; Ogata, K.; Kuratani, N. [Institute of Physics, University of Sao Paulo, C. P. 66318, 05315-970, Sao Paolo, SP (Brazil); Nissin Electric Company, Ltd., 47, Umezu-Takase-cho, Ukyo-ku, Kyota 615-8686 (Japan)

    2005-01-01T23:59:59.000Z

    Thin titanium nitride films were prepared at room temperature by titanium metal vapor deposition on silicon substrates with simultaneous irradiation by a 2 keV nitrogen ion beam. Arrival rate ratios, ARR(N/Ti), defined as the ratio of the flux of incident atomic nitrogen particles in the ion beam relative to the flux of titanium atoms transported to the substrate, ranged from 0.17 to 2.5. The gas pressure in the vacuum chamber was maintained at 1.3x10{sup -3} or 6.7x10{sup -3} Pa during the deposition and irradiation process. Analyses of Ti 2p x-ray photoelectron spectroscopy spectra indicated the presence of metal Ti{sup 0}, nitride TiN, oxide TiO{sub 2}, oxynitride TiN{sub x}O{sub y}, and carbide TiC phases. The Ti{sup 0} phase was observed exclusively and predominantly in the films prepared at 1.3x10{sup -3} Pa and ARR(N/Ti)=0.17, 0.21, and 0.28, and the TiN phase is major in the others, as confirmed by the x-ray diffractometry analyses. The chemical composition ratio N/Ti in the films prepared at 1.3x10{sup -3} Pa increased linearly with increasing ARR(N/Ti) up to ARR(N/Ti)=0.42 and tended to be constant with further increase in ARR(N/Ti), while this ratio in the films prepared at 6.7x10{sup -3} Pa was almost constant independently of ARR(N/Ti), similar to the constant value observed at 1.3x10{sup -3} Pa and higher ARR(N/Ti). This dependence may be understood by comparison with the flux of evaporated titanium atoms, the flux of nitrogen in the beam, and the impingement rate of nitrogen gas in the vacuum chamber, evaluated through the kinetic theory of gases. On the other hand, titanium is known to be one of the chemically active materials which form stable compounds with gases by chemisorption, this fact leading to considerable incorporation of contaminant oxygen and carbon in the depositing titanium film.

  17. anultra high pressure: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    c. Y Christian P Burger (i&Iember) Randall Getger ( Member) 5wc Fr. Walter F. Bradley (Head of Department) May 1991 ABSTRACT A Temperature Compensated Pressure Transducer for...

  18. Effect of high-pressure on molecular magnetism 

    E-Print Network [OSTI]

    Prescimone, Alessandro

    2010-01-01T23:59:59.000Z

    The effect of pressure on a number of magnetically interesting compounds such as single-molecule magnets and dimeric copper and manganese molecules has been investigated to probe the validity of ambient magneto-structural ...

  19. Instrumentation development for neutron scattering at high pressure 

    E-Print Network [OSTI]

    Fang, Junwei

    2012-11-29T23:59:59.000Z

    Neutron scattering at extremes of pressure is a powerful tool for studying the response of structural and magnetic properties of materials on microscopic level to applied stresses. However, experimental neutron studies ...

  20. Moessbauer studies of iron hydride at high pressure

    SciTech Connect (OSTI)

    Choe, I.; Ingalls, R. (Department of Physics, FM-15, University of Washington, Seattle, Washington 98195 (USA)); Brown, J.M.; Sato-Sorensen, Y. (Geophysics Program, AK-50, University of Washington, Seattle, Washington 98195 (USA)); Mills, R. (Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (USA))

    1991-07-01T23:59:59.000Z

    We have measured {ital in} {ital situ} Moessbauer spectra of iron hydride made in a diamond anvil cell at high pressure and room temperature. The spectra show a sudden change at 3.5{plus minus}0.5 GPa from a single hyperfine pattern to a superposition of three. The former pattern results from normal {alpha}-iron with negligible hydrogen content, and the latter from residual {alpha}-iron plus newly formed iron hydride. Between 3.5 and 10.4 GPa, the extra hydride pattern have hyperfine fields for one ranging from 276 to 263 kOe, and the other, from 317 to 309 kOe. Both have isomer shifts of about 0.4 mm/sec, and negligible quadrupole splittings. X-ray studies on quenched samples have shown that iron hydride is of double hexagonal close-packed structure, whose two nonequivalent iron sites may account for the observation of two different patterns. Even allowing for the effect of volume expansion, the observed isomer shifts for the hydride are considerably more positive than those of other metallic phases of iron. At the same time, the hyperfine fields are slightly smaller than that of {alpha}-iron. As a possible explanation, one may expect a bonding of hydrogen with iron, which would result in a small reduction of 4{ital s} electrons, possibly accompanied by a small increase of 3{ital d} electrons compared with the neutral atom in metallic iron. The difference between the hyperfine fields in the two spectra are presumably due to the different symmetry at the two iron sites.

  1. An in situ tensile test apparatus for polymers in high pressure hydrogen

    SciTech Connect (OSTI)

    Alvine, K. J., E-mail: kyle.alvine@pnnl.gov; Kafentzis, T. A.; Pitman, S. G.; Johnson, K. I.; Skorski, D.; Tucker, J. C.; Roosendaal, T. J.; Dahl, M. E. [Energy and Environment Directorate, Pacific Northwest National Laboratory, Richland, Washington 99354 (United States)

    2014-10-15T23:59:59.000Z

    Degradation of material properties by high-pressure hydrogen is an important factor in determining the safety and reliability of materials used in high-pressure hydrogen storage and delivery. Hydrogen damage mechanisms have a time dependence that is linked to hydrogen outgassing after exposure to the hydrogen atmosphere that makes ex situ measurements of mechanical properties problematic. Designing in situ measurement instruments for high-pressure hydrogen is challenging due to known hydrogen incompatibility with many metals and standard high-power motor materials such as Nd. Here we detail the design and operation of a solenoid based in situ tensile tester under high-pressure hydrogen environments up to 42 MPa (6000 psi). Modulus data from high-density polyethylene samples tested under high-pressure hydrogen at 35 MPa (5000 psi) are also reported as compared to baseline measurements taken in air.

  2. An In-situ Tensile Test Apparatus for Polymers in High Pressure Hydrogen

    SciTech Connect (OSTI)

    Alvine, Kyle J.; Kafentzis, Tyler A.; Pitman, Stan G.; Johnson, Kenneth I.; Skorski, Daniel C.; Tucker, Joseph C.; Roosendaal, Timothy J.; Dahl, Michael E.

    2014-10-10T23:59:59.000Z

    Degradation of material properties by high-pressure hydrogen is an important factor in determining the safety and reliability of materials used in high-pressure hydrogen storage and delivery. Hydrogen damage mechanisms have a time dependence that is linked to hydrogen outgassing after exposure to the hydrogen atmosphere that makes ex-situ measurements of mechanical properties problematic. Designing in-situ measurement instruments for high-pressure hydrogen is challenging due to known hydrogen incompatibility with many metals and standard high-power motor materials like Nd. Here we detail the design and operation of a solenoid based in-situ tensile tester under high-pressure hydrogen environments up to 5,000 psi. Modulus data from high-density polyethylene (HDPE) samples tested under high-pressure hydrogen are also reported as compared to baseline measurements taken in air.

  3. Development of Designer Diamond Technology for High Pressure High Temperature Experiments in Support of Stockpile Stewardship Program

    SciTech Connect (OSTI)

    Vohra, Yogesh, K.

    2009-10-28T23:59:59.000Z

    The role of nitrogen in the fabrication of designer diamond was systematically investigated by adding controlled amount of nitrogen in hydrogen/methane/oxygen plasma. This has led to a successful recipe for reproducible fabrication of designer diamond anvils for high-pressure high-temperature research in support of stockpile stewardship program. In the three-year support period, several designer diamonds fabricated with this new growth chemistry were utilized in high-pressure experiments at UAB and Lawrence Livermore National Laboratory. The designer diamond anvils were utilized in high-pressure studies on heavy rare earth metals, high pressure melting studies on metals, and electrical resistance measurements on iron-based layered superconductors under high pressures. The growth chemistry developed under NNSA support can be adapted for commercial production of designer diamonds.

  4. Split stream boilers for high-temperature/high-pressure topping steam turbine combined cycles

    SciTech Connect (OSTI)

    Rice, I.G. [Rice (I.G.), Spring, TX (United States)

    1997-04-01T23:59:59.000Z

    Research and development work on high-temperature and high-pressure (up to 1,500 F TIT and 4,500 psia) topping steam turbines and associated steam generators for steam power plants as well as combined cycle plants is being carried forward by DOE, EPRI, and independent companies. Aeroderivative gas turbines and heavy-duty gas turbines both will require exhaust gas supplementary firing to achieve high throttle temperatures. This paper presents an analysis and examples of a split stream boiler arrangement for high-temperature and high-pressure topping steam turbine combined cycles. A portion of the gas turbine exhaust flow is run in parallel with a conventional heat recovery steam generator (HRSG). This side stream is supplementary fired opposed to the current practice of full exhaust flow firing. Chemical fuel gas recuperation can be incorporated in the side stream as an option. A significant combined cycle efficiency gain of 2 to 4 percentage points can be realized using this split stream approach. Calculations and graphs show how the DOE goal of 60 percent combined cycle efficiency burning natural gas fuel can be exceeded. The boiler concept is equally applicable to the integrated coal gas fuel combined cycle (IGCC).

  5. High-pressure study of isoviolanthrone by Raman spectroscopy

    SciTech Connect (OSTI)

    Zhao, Xiao-Miao; Huang, Qiao-Wei [Department of Physics, South China University of Technology, Guangzhou 510640 (China); Center for High Pressure Science and Technology Advanced Research, Shanghai 201203 (China); Zhang, Jiang [Department of Physics, South China University of Technology, Guangzhou 510640 (China); Zhong, Guo-Hua [Center for Photovoltaics and Solar Energy, Shenzhen Institutes of Advanced Technology, Chinese Academy of Sciences, Shenzhen 518055 (China); Lin, Hai-Qing [Beijing Computational Science Research Center, Beijing 100084 (China); Chen, Xiao-Jia, E-mail: xjchen@hpstar.ac.cn [Center for High Pressure Science and Technology Advanced Research, Shanghai 201203 (China); Geophysical Laboratory, Carnegie Institution of Washington, Washington, DC 20015 (United States)

    2014-06-28T23:59:59.000Z

    Vibrational properties of isoviolanthrone are investigated by Raman scattering at pressures up to 30.5 GPa and room temperature. A complete characterization of phonon spectra under pressure is given for this material. The onset of a phase transition at 11.0 GPa and the formation of a new phase above 13.8 GPa are identified from both the frequency shifts and the changes in the full width half maxima of the intra- and internal modes. The transition is proposed to result from the changes of intra- and intermolecular bonding. The tendencies of the intensity ratios with pressure are in good agreement with the pressure dependence of the resistance at room temperature, indicating that the phase transition may be an electronic origin. The absence of the changes in the lattice modes indicates that the observed phase transition is probably a result of the structural distortions or reorganizations. The reversible character of the transition upon compression and decompression is determined in the entire pressure region studied.

  6. Constant pressure high throughput membrane permeation testing system

    DOE Patents [OSTI]

    Albenze, Erik J.; Hopkinson, David P.; Luebke, David R.

    2014-09-02T23:59:59.000Z

    The disclosure relates to a membrane testing system for individual evaluation of a plurality of planar membranes subjected to a feed gas on one side and a sweep gas on a second side. The membrane testing system provides a pressurized flow of a feed and sweep gas to each membrane testing cell in a plurality of membrane testing cells while a stream of retentate gas from each membrane testing cell is ported by a retentate multiport valve for sampling or venting, and a stream of permeate gas from each membrane testing cell is ported by a permeate multiport valve for sampling or venting. Back pressure regulators and mass flow controllers act to maintain substantially equivalent gas pressures and flow rates on each side of the planar membrane throughout a sampling cycle. A digital controller may be utilized to position the retentate and permeate multiport valves cyclically, allowing for gas sampling of different membrane cells over an extended period of time.

  7. High Pressure Neutron Powder Diffraction Study of Superhydrated Natrolite

    SciTech Connect (OSTI)

    Colligan,M.; Lee, Y.; Vogt, T.; Celestian, A.; Parise, J.; Marshall, W.; Hriljac, J.

    2005-01-01T23:59:59.000Z

    Neutron powder diffraction data were collected on a sample of natrolite and a 1:1 (v/v) mixture of perdeuterated methanol and water at a pressure of 1.87(11) GPa. The natrolite sample was superhydrated, with a water content double that observed at ambient pressure. All of the water deuterium atoms were located and the nature and extent of the hydrogen bonding elucidated for the first time. This has allowed the calculation of bond valence sums for the water oxygen atoms, and from this, it can be deduced that the key energetic factor leading to loss of the additional water molecule upon pressure release is the poor coordination to sodium cations within the pores.

  8. Ultrafast high strain rate acoustic wave measurements at high static pressure in a diamond anvil cell

    SciTech Connect (OSTI)

    Armstrong, M; Crowhurst, J; Reed, E; Zaug, J

    2008-02-04T23:59:59.000Z

    We have used sub-picosecond laser pulses to launch ultra-high strain rate ({approx} 10{sup 9} s{sup -1}) nonlinear acoustic waves into a 4:1 methanol-ethanol pressure medium which has been precompressed in a standard diamond anvil cell. Using ultrafast interferometry, we have characterized acoustic wave propagation into the pressure medium at static compression up to 24 GPa. We find that the velocity is dependent on the incident laser fluence, demonstrating a nonlinear acoustic response which may result in shock wave behavior. We compare our results with low strain, low strain-rate acoustic data. This technique provides controlled access to regions of thermodynamic phase space that are otherwise difficult to obtain.

  9. Gibbs-Thomson formula for small island sizes: Corrections for high vapor densities Badrinarayan Krishnamachari, James McLean,* Barbara Cooper, and James Sethna

    E-Print Network [OSTI]

    Sethna, James P.

    Gibbs-Thomson formula for small island sizes: Corrections for high vapor densities Badrinarayan island and its curvature. The ``classical'' form of this relationship is the Gibbs-Thomson formula, which model, performed for various sizes of islands, do not fit very well to the Gibbs- Thomson formula. We

  10. Phase stability of carbon clathrates at high pressure Jian-Tao Wang,1,a

    E-Print Network [OSTI]

    Wang, Wei Hua

    Phase stability of carbon clathrates at high pressure Jian-Tao Wang,1,a Changfeng Chen,2 Ding, Institute of Physics, Chinese Academy of Sciences, Beijing 100080, China 2 Department of Physics and Hi an ab initio study on the structural stability of carbon clathrates at high pressure and identify fcc

  11. Engine with hydraulic fuel injection and ABS circuit using a single high pressure pump

    DOE Patents [OSTI]

    Bartley, Bradley E. (Manito, IL); Blass, James R. (Bloomington, IL); Gibson, Dennis H. (Chillicothe, IL)

    2001-01-01T23:59:59.000Z

    An engine system comprises a hydraulically actuated fuel injection system and an ABS circuit connected via a fluid flow passage that provides hydraulic fluid to both the fuel injection system and to the ABS circuit. The hydraulically actuated system includes a high pressure pump. The fluid control passage is in fluid communication with an outlet from the high pressure pump.

  12. Properties of nanostructured diamond-silicon carbide composites sintered by high pressure infiltration technique

    E-Print Network [OSTI]

    Gubicza, Jenõ

    peak profiles using Fourier coefficients of ab initio theoretical size and strain profiles Materials Research Society 2703 #12;electric power dissipated in the apparatus. Obtained power­ temperature and load­pressure plots were used as the calibration curves for subsequent high-pressure, high- temperature

  13. Optically accessible high-pressure combustion apparatus Stephen D. Tsea)

    E-Print Network [OSTI]

    Tse, Stephen D.

    . DOI: 10.1063/1.1634358 I. INTRODUCTION Recognizing that combustion processes within internal combustion engines take place in elevated pressure environ- ments, that most fundamental information of atmospheres, and hence are representative of those in inter- nal combustion engines. Of particular interest

  14. Instrumentation development for magneto-transport and neutron scattering measurements at high pressure and low temperature 

    E-Print Network [OSTI]

    Wang, Weiwei

    2013-07-01T23:59:59.000Z

    High pressure, high magnetic field and low temperature techniques are required to investigate magnetic transitions and quantum critical behaviour in different ferromagnetic materials to elucidate how novel forms of ...

  15. High pressure ejection of melt from a reactor pressure vessel. The discharge phase. Revision 7

    SciTech Connect (OSTI)

    Pilch, M.; Tarbell, W.M.

    1985-09-01T23:59:59.000Z

    Recent probabilistic risk-assessment studies identified potential accident sequences in which reactor vessel failure occurs while the primary system is at elevated pressure. The phenomenology of the discharge phase is reviewed here. We propose an improved model for hole ablation following vessel failure, and we compare the model with experiment data. Gas blowthrough is identified as a mechanism that allows steam to escape through the vessel breach before melt ejection is complete. Gas blowthrough leads to pneumatic atomization of the remaining melt before significant depressurization of the primary system occurs.

  16. An Innovative High-Temperature High-Pressure Measurement While Drilling (MWD) Tool

    SciTech Connect (OSTI)

    Brian Boling

    2007-06-01T23:59:59.000Z

    Measurement while drilling (MWD) tools specified to 150 C (302 F) that provide wellbore surveys, real-time inclination, and natural gamma ray detection are a commodity item in the oilfield services industry. MWD tools specified to 175 C (347 F) that routinely demonstrate highly reliable operation are available from only a few service companies. Commercial MWD tools that reliably operate to 200 C (392 F) for extended periods of time and offer features like real-time gamma ray, retrievability, and reseatability are nonexistent. Need for these higher temperature tools will increase as wells become hotter in the search for new oil and gas resources. The goal of this project was to design a retrievable and reseatable high-pressure/high-temperature MWD tool with real-time continuous inclination, vibration detection, annular pressure, and gamma ray detection. This report describes the development of such a tool from concept, through feasibility, and into field testing and preliminary development planning. It describes the challenges encountered in the design of the tool, along with testing results and decisions about the commercial viability of the tool in the configuration in which it was developed. The decision was made not to commercialize the tool developed under this project because of a combination of battery technology problems and modulation power consumption at the required depths.

  17. High-temperature, high-pressure bonding of nested tubular metallic components

    DOE Patents [OSTI]

    Quinby, Thomas C. (Kingston, TN)

    1980-01-01T23:59:59.000Z

    This invention is a tool for effecting high-temperature, high-compression bonding between the confronting faces of nested, tubular, metallic components. In a typical application, the tool is used to produce tubular target assemblies for irradiation in nuclear reactors or particle accelerators, the target assembly comprising a uranium foil and an aluminum-alloy substrate. The tool preferably is composed throughout of graphite. It comprises a tubular restraining member in which a mechanically expandable tubular core is mounted to form an annulus with the member. The components to be bonded are mounted in nested relation in the annulus. The expandable core is formed of individually movable, axially elongated segments whose outer faces cooperatively define a cylindrical pressing surface and whose inner faces cooperatively define two opposed, inwardly tapered, axial bores. Tapered rams extend respectively into the bores. The loaded tool is mounted in a conventional hot-press provided with evacuation means, heaters for maintaining its interior at bonding temperature, and hydraulic cylinders for maintaining a selected inwardly directed pressure on the tapered rams. With the hot-press evacuated and the loaded tool at the desired temperature, the cylinders are actuated to apply the selected pressure to the rams. The rams in turn expand the segmented core to maintain the nested components in compression against the restraining member. These conditions are maintained until the confronting faces of the nested components are joined in a continuous, uniform bond characterized by high thermal conductivity.

  18. Solid Nitrogen at Extreme Conditions of High Pressure and Temperature

    SciTech Connect (OSTI)

    Goncharov, A; Gregoryanz, E

    2004-04-05T23:59:59.000Z

    We review the phase diagram of nitrogen in a wide pressure and temperature range. Recent optical and x-ray diffraction studies at pressures up to 300 GPa and temperatures in excess of 1000 K have provided a wealth of information on the transformation of molecular nitrogen to a nonmolecular (polymeric) semiconducting and two new molecular phases. These newly found phases have very large stability (metastability) range. Moreover, two new molecular phases have considerably different orientational order from the previously known phases. In the iota phase (unlike most of other known molecular phases), N{sub 2} molecules are orientationally equivalent. The nitrogen molecules in the theta phase might be associated into larger aggregates, which is in line with theoretical predictions on polyatomic nitrogen.

  19. Speed of sound in liquids at high pressure

    E-Print Network [OSTI]

    P., Kielczynski; S, Piekarski

    2013-01-01T23:59:59.000Z

    In this paper, a new general formula for the sound speed in adiabatic conditions ( S = const ) has been established. The sound speed depends on the mass density {\\rho} (p,T ) and the internal energy per unit mass E(p,T ), both expressed as functions of the pressure p and the temperature T . This formula has been compared with experimental data on the example of triolein over the pressure range up to 450 MPa. For experimental data, phenomenological approximate formulas have been proposed. Those formulas have two versions, depending on the 2 and 3 parameters. Both versions have been developed with the help of the new expression (Eq.8) for the sound speed. The explicit form of both approximate curves can be regarded as the result of purely phenomenological modeling. However, in this paper, these new analytical expressions have been obtained by applying the heuristic procedure described in Appendix.

  20. Structural stability of methane hydrate at high pressures

    SciTech Connect (OSTI)

    Shu, Jinfu; Chen, Xiaojia; Chou, I.-Ming; Yang, Wenge; Hu, Jingzhu; Hemley, Russell J.; Mao, Ho-kwang

    2011-01-01T23:59:59.000Z

    The structural stability of methane hydrate under pressure at room temperature was examined by both in-situ single-crystal and powder X-ray diffraction techniques on samples with structure types I, II, and H in diamond-anvil cells. The diffraction data for types II (sII) and H (sH) were refined to the known structures with space groups Fd3m and P6{sub 3}/mmc, respectively. Upon compression, sI methane hydrate transforms to the sII phase at 120 MPa, and then to the sH phase at 600 MPa. The sII methane hydrate was found to coexist locally with sI phase up to 500 MPa and with sH phase up to 600 MPa. The pure sH structure was found to be stable between 600 and 900 MPa. Methane hydrate decomposes at pressures above 3 GPa to form methane with the orientationally disordered Fm3m structure and ice VII (Pn3m). The results highlight the role of guest (CH{sub 4})-host (H{sub 2}O) interactions in the stabilization of the hydrate structures under pressure.

  1. Structure Stability of Methane Hydrate at High Pressures

    SciTech Connect (OSTI)

    J Shu; X Chen; I Chou; W Yang; J Hu; R Hemley; K Mao

    2011-12-31T23:59:59.000Z

    The structural stability of methane hydrate under pressure at room temperature was examined by both in-situ single-crystal and powder X-ray diffraction techniques on samples with structure types I, II, and H in diamond-anvil cells. The diffraction data for types II (sII) and H (sH) were refined to the known structures with space groups Fd3m and P6{sub 3}/mmc, respectively. Upon compression, sI methanehydrate transforms to the sII phase at 120 MPa, and then to the sH phase at 600 MPa. The sII methanehydrate was found to coexist locally with sI phase up to 500 MPa and with sH phase up to 600 MPa. The pure sH structure was found to be stable between 600 and 900 MPa. Methanehydrate decomposes at pressures above 3 GPa to form methane with the orientationally disordered Fm3mstructure and ice VII (Pn3m). The results highlight the role of guest (CH{sub 4})-host (H{sub 2}O) interactions in the stabilization of the hydratestructures under pressure.

  2. Heat transfer and pressure drop data for high heat flux densities to water at high subcritical pressures

    E-Print Network [OSTI]

    Rohsenow, Warren M.

    1951-01-01T23:59:59.000Z

    Local surface ooeffioients of heat t-ansfer, overall pressure drop data and mean friction factor are presented for heat flamms up to 3.52106 BtuAr ft2 for water flowing in a nickel tabe isder the following conditions: mass ...

  3. High explosives vapor detection by atmospheric sampling glow discharge ionization/tandem mass spectrometry

    SciTech Connect (OSTI)

    McLuckey, S.A.; Goeringer, D.E.; Asano, K.G. [Oak Ridge National Lab., TN (United States). Chemical and Analytical Sciences Div.

    1996-02-01T23:59:59.000Z

    The combination of atmospheric sampling glow discharge ionization with tandem mass spectrometry for the detection of traces of high explosives is described. Particular emphasis is placed on use of the quadrupole ion trap as the type of tandem mass spectrometer. Atmospheric sampling glow discharge provides a simple, rugged, and efficient means for anion formation while the quadrupole ion trap provides for efficient tandem mass spectrometry. Mass selective ion accumulation and non-specific ion activation methods can be used to overcome deleterious effects arising from ion/ion interactions. Such interactions constitute the major potential technical barrier to the use of the ion trap for real-time monitoring of targeted compounds in uncontrolled and highly variable matrices. Tailored waveforms can be used to effect both mass selective ion accumulation and ion activation. Concatenated tailored waveforms allow for both functions in a single experiment thereby providing the capability for monitoring several targeted species simultaneously. The combination of atmospheric sampling glow discharge ionization with a state-of-the-art analytical quadrupole ion trap is a highly sensitive and specific detector for traces of high explosives. The combination is also small and inexpensive relative to virtually any other form of tandem mass spectrometry. The science and technology underlying the glow discharge/ion trap combination is sufficiently mature to form the basis for an engineering effort to make the detector portable. 85 refs.

  4. Experimental evidence for interaction of water vapor and platinum crucibles at high temperatures : Implications for volatiles

    E-Print Network [OSTI]

    Cartigny, Pierre

    The extraction of water from igneous rocks and minerals is classically achieved by induction heating or foils, to extract water from rocks or minerals should be avoided. The interaction high- lighted : Implications for volatiles from igneous rocks and minerals Matthieu Clog , Pierre Cartigny, Cyril Aubaud

  5. Vapor pressures of mixtures of CFC-114 with the potential replacement coolants C{sub 4}F{sub 10} and c-C{sub 4}F{sub 8}

    SciTech Connect (OSTI)

    Trowbridge, L.D. [Oak Ridge K-25 Site, TN (United States); Otey, M.G. [Paducah Gaseous Diffusion Plant, KY (United States)

    1994-09-01T23:59:59.000Z

    The U.S. Enrichment Corporation`s production of isotopically enriched uranium depends solely on two plants which utilize the gaseous diffusion process. This process uses large quantities of CFC-114 as an evaporative coolant. CFC-114, however, will be phased out of production at the end of 1995 due to its potential to deplete stratospheric ozone. A search has been underway for substitutes for a number of years. The initial search (1988-89) for an ozone-friendly, commercially available, chemically compatible substitute yielded two candidates, FC-c318 (c-C{sub 4}F{sub 8}) and FC-3110 (C{sub 4}F{sub 10}). The intended mode of replacing coolant was to stage the new coolant into independent subsystems of the plants, so that some systems would continue to operate on CFC-114, and an increasing number would operate on the new coolant. During that changeover process, the possibility of coolant mixing arises in variety of scenarios. This work was intended to generate sufficient experimental information to be able to predict the vapor pressure of coolant mixtures over the range of operating conditions likely to be found in the diffusion plants. Specifically, vapor pressures were measured over the temperature range 322 to 355 K (120{degrees}F to 180{degrees}F) and over the full range of mole fractions for binary mixtures of CFC-114 with FC-3110, and of CFC-114 with FC-c318.

  6. Experimental and Modeling Study of the Flammability of Fuel Tank Headspace Vapors from High Ethanol Content Fuels

    SciTech Connect (OSTI)

    Gardiner, D.; Bardon, M.; Pucher, G.

    2008-10-01T23:59:59.000Z

    Study determined the flammability of fuel tank headspace vapors as a function of ambient temperature for seven E85 fuel blends, two types of gasoline, and denatured ethanol at a low tank fill level.

  7. The effect of condensate dropout on pressure transient analysis of a high-pressure gas condensate well

    E-Print Network [OSTI]

    Briens, Frederic Jean-Louis

    1986-01-01T23:59:59.000Z

    of drawdown or buildup tests, the formation permeability can be estimated. Although these conventional techniques have been successfully applied to 'dry' gas well analysis, they have not been extended to high-pressure gas condensate wells. The application... Condensate Reser voir Data. . 43 Elf Aquitaine Gas Condensate Reservoir Fluid Composition Elf Aquitaine Gas Condensate Well Production Test Data. Drawdown Test F1 of Elf Aquitaine Gas Condensate Mell 45 46 Drawdown Test F2 of Elf Aquitaine Gas...

  8. Development of a High-Pressure/High-Temperature Downhole Turbine Generator

    SciTech Connect (OSTI)

    Timothy F. Price

    2007-02-01T23:59:59.000Z

    The objective of this project as originally outlined has been to achieve a viable downhole direct current (DC) power source for extreme high pressure, high temperature (HPHT) environments of >25,000 psi and >250 C. The Phase I investigation posed and answered specific questions about the power requirements, mode of delivery and form factor the industry would like to see for downhole turbine generator tool for the HPHT environment, and noted specific components, materials and design features of that commercial system that will require upgrading to meet the HPHT project goals. During the course of Phase I investigation the scope of the project was HPHT downhole DC power. Phase I also investigated the viability of modifying a commercial expanded, without additional cost expected to the project, to include the addition of HT batteries to the power supply platform.

  9. High pressure testing of see-through labyrinth seals

    E-Print Network [OSTI]

    Picardo, Arthur Michael

    2003-01-01T23:59:59.000Z

    of labyrinth tooth Impedance Inches of water [UT'] [L) [L) [FT/L] [FT/L] [FT/L] [FT/L] [L] [L] [F] [F] [UT ] [L] [F/L] [L] K;; m, N NT pe PR PS R Direct stiffness Cross-coupled stiffness Stiffness Coefficient Seal Length Stator... the exit-labyrinth seals. Section A-A in Figure 4 gives the location of swirl brakes. Btmor Inlet Annulus Back Pr'asnua Anfsrlur Shaker Btmgars (2 (9 90 ) Thmmomuple Pressure Traraduccfs (2 e sf ) et Prrmnlrf Btrg Pmmum Therm ocormles Transducers...

  10. A low phase noise microwave frequency synthesis for a high-performance cesium vapor cell atomic clock

    SciTech Connect (OSTI)

    François, B.; Boudot, R. [FEMTO-ST, CNRS, Université de Franche-Comté, 26 chemin de l'Epitaphe, 25030 Besançon (France); Calosso, C. E. [INRIM, Strada delle Cacce 91, 10135 Torino (Italy); Danet, J. M. [LNE-SYRTE, Observatoire de Paris, CNRS-UPMC, 61 avenue de l'Observatoire, 75014 Paris (France)

    2014-09-15T23:59:59.000Z

    We report the development, absolute phase noise, and residual phase noise characterization of a 9.192?GHz microwave frequency synthesis chain devoted to be used as a local oscillator in a high-performance cesium vapor cell atomic clock based on coherent population trapping (CPT). It is based on frequency multiplication of an ultra-low phase noise 100 MHz oven-controlled quartz crystal oscillator using a nonlinear transmission line-based chain. Absolute phase noise performances of the 9.192?GHz output signal are measured to be ?42, ?100, ?117 dB?rad{sup 2}/Hz and ?129 dB?rad{sup 2}/Hz at 1 Hz, 100 Hz, 1 kHz, and 10 kHz offset frequencies, respectively. Compared to current results obtained in a state-of-the-art CPT-based frequency standard developed at LNE-SYRTE, this represents an improvement of 8 dB and 10 dB at f = 166 Hz and f = 10 kHz, respectively. With such performances, the expected Dick effect contribution to the atomic clock short term frequency stability is reported at a level of 6.2 × 10{sup ?14} at 1 s integration time, that is a factor 3 higher than the atomic clock shot noise limit. Main limitations are pointed out.

  11. Lithium pellet injection into high pressure magnetically confined plasmas

    E-Print Network [OSTI]

    Böse, Brock (Brock Darrel)

    2010-01-01T23:59:59.000Z

    The ablation of solid pellets injected into high temperature magnetically confined plasmas is characterized by rapid oscillations in the ablation rate, and the formation of field aligned filaments in the ablatant. High ...

  12. Molecular Surface Chemistry by Metal Single Crystals and Nanoparticles from Vacuum to High Pressure.

    SciTech Connect (OSTI)

    Somorjai, Gabor A.; Park, Jeong Y.

    2008-04-05T23:59:59.000Z

    Model systems for studying molecular surface chemistry have evolved from single crystal surfaces at low pressure to colloidal nanoparticles at high pressure. Low pressure surface structure studies of platinum single crystals using molecular beam surface scattering and low energy electron diffraction techniques probe the unique activity of defects, steps and kinks at the surface for dissociation reactions (H-H, C-H, C-C, O{double_bond}O bonds). High-pressure investigations of platinum single crystals using sum frequency generation vibrational spectroscopy have revealed the presence and the nature of reaction intermediates. High pressure scanning tunneling microscopy of platinum single crystal surfaces showed adsorbate mobility during a catalytic reaction. Nanoparticle systems are used to determine the role of metal-oxide interfaces, site blocking and the role of surface structures in reactive surface chemistry. The size, shape and composition of nanoparticles play important roles in determining reaction activity and selectivity.

  13. Persistent global proton aurora caused by high solar wind dynamic pressure

    E-Print Network [OSTI]

    Bergen, Universitetet i

    Persistent global proton aurora caused by high solar wind dynamic pressure K. M. Laundal1 and N] Global images of the proton aurora taken with the SI-12 camera onboard the IMAGE satellite reveal a very direct relationship between the solar wind dynamic pressure and the intensity of the global proton aurora

  14. Fractal characterisation of high-pressure and hydrogen-enriched CH4air turbulent premixed flames

    E-Print Network [OSTI]

    Gülder, �mer L.

    Fractal characterisation of high-pressure and hydrogen-enriched CH4­air turbulent premixed flames measurements were performed to obtain the flame front images, which were further analyzed for fractal of the flame front curvature as a function of the pressure. Fractal dimension showed a strong dependence

  15. Hydrogen incorporation in stishovite at high pressure and symmetric hydrogen bonding in N-AlOOH

    E-Print Network [OSTI]

    Stixrude, Lars

    Hydrogen incorporation in stishovite at high pressure and symmetric hydrogen bonding in N significant amounts of hydrogen in stishovite under lower-mantle conditions. The enthalpy of solution pressure and temperature. We predict asymmetric hydrogen bonding in the stishovite^N-AlOOH solid solution

  16. Wear damage resulting from sliding impact kinematics in pressurized high temperature water: energetical and

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 Wear damage resulting from sliding impact kinematics in pressurized high temperature water.bec@ec-lyon.fr Abstract Specific wear of Rod Cluster Control Assemblies (RCCA) in Pressurized Water nuclear Reactors (PWR) results from contacts with their guides due to flow induced vibration. Particular sliding impact contact

  17. SOLAR RADIATION PRESSURE EFFECTS ON VERY HIGH-ECCENTRIC FORMATION J. Fontdecaba Baig1

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    SOLAR RADIATION PRESSURE EFFECTS ON VERY HIGH-ECCENTRIC FORMATION FLYING J. Fontdecaba Baig1 , G. M this particular relative motion is the scoop of this paper. Main perturbation in HEO orbits are solar radiation. Key words: formation flying, HEO orbits, solar radiation pressure. 1. INTRODUCTION Formation flying

  18. Fermi Surface of Uranium at Ambient Pressure Gregory S. Boebinger, National High Magnetic Field Laboratory

    E-Print Network [OSTI]

    Weston, Ken

    Fermi Surface of ­Uranium at Ambient Pressure Gregory S. Boebinger, National High Magnetic Field Laboratory DMR-Award 0654118 DC Field Facility User Program The fermi surface of ­Uranium has been measured surface of alpha-uranium at ambient pressure, Phys. Rev. B Rapid Commun., 80, 241101 (2009). B//c-axis B

  19. Alternated high-and low-pressure nitriding of austenitic stainless steel: Mechanisms and results

    E-Print Network [OSTI]

    Alternated high- and low-pressure nitriding of austenitic stainless steel: Mechanisms and results G a gas mixture of (N2 /H2):(50/50) in pressure, was applied to stainless-steel AISI 304. In the first or plasma nitriding of metal parts, in par- ticular those made of steel and cast iron, is extensively ap

  20. Overview of Hanford Site High-Level Waste Tank Gas and Vapor Dynamics

    SciTech Connect (OSTI)

    Huckaby, James L.; Mahoney, Lenna A.; Droppo, James G.; Meacham, Joseph E.

    2004-08-31T23:59:59.000Z

    Hanford Site processes associated with the chemical separation of plutonium from uranium and other fission products produced a variety of volatile, semivolatile, and nonvolatile organic and inorganic waste chemicals that were sent to high-level waste tanks. These chemicals have undergone and continue to undergo radiolytic and thermal reactions in the tanks to produce a wide variety of degradation reaction products. The origins of the organic wastes, the chemical reactions they undergo, and their reaction products have recently been examined by Stock (2004). Stock gives particular attention to explaining the presence of various types of volatile and semivolatile organic species identified in headspace air samples. This report complements the Stock report by examining the storage of volatile and semivolatile species in the waste, their transport through any overburden of waste to the tank headspaces, the physical phenomena affecting their concentrations in the headspaces, and their eventual release into the atmosphere above the tanks.

  1. High Pressure X-ray Diffraction Study on Icosahedral Boron Arsenide (B12As2)

    SciTech Connect (OSTI)

    J Wu; H Zhu; D Hou; C Ji; C Whiteley; J Edgar; Y Ma

    2011-12-31T23:59:59.000Z

    The high pressure properties of icosahedral boron arsenide (B12As2) were studied by in situ X-ray diffraction measurements at pressures up to 25.5 GPa at room temperature. B12As2 retains its rhombohedral structure; no phase transition was observed in the pressure range. The bulk modulus was determined to be 216 GPa with the pressure derivative 2.2. Anisotropy was observed in the compressibility of B12As2-c-axis was 16.2% more compressible than a-axis. The boron icosahedron plays a dominant role in the compressibility of boron-rich compounds.

  2. Electrolyte vapor condenser

    DOE Patents [OSTI]

    Sederquist, R.A.; Szydlowski, D.F.; Sawyer, R.D.

    1983-02-08T23:59:59.000Z

    A system is disclosed for removing electrolyte from a fuel cell gas stream. The gas stream containing electrolyte vapor is supercooled utilizing conventional heat exchangers and the thus supercooled gas stream is passed over high surface area passive condensers. The condensed electrolyte is then drained from the condenser and the remainder of the gas stream passed on. The system is particularly useful for electrolytes such as phosphoric acid and molten carbonate, but can be used for other electrolyte cells and simple vapor separation as well. 3 figs.

  3. High Pressure Shock Tube Studies of Fuel Combustion Engineering The high-pressure single-pulse shock tube is shown in Figure 8 (rated at 5 to 1000 atm,

    E-Print Network [OSTI]

    Ben-Arie, Jezekiel

    High Pressure Shock Tube Studies of Fuel Combustion Engineering The high-pressure single and oxidative degradation of various components in order to identify the products as guides to the combustion

  4. APPLICATION OF CERAMICS TO HIGH PRESSURE FUEL SYSTEMS

    SciTech Connect (OSTI)

    Mandler, Jr., William F.

    2000-08-20T23:59:59.000Z

    Diesel fuel systems are facing increased demands as engines with reduced emissions are developed. Injection pressures have increased to provide finer atomization of fuel for more efficient combustion, Figure 1. This increases the mechanical loads on the system and requires tighter clearances between plungers and bores to prevent leakage. At the same time, fuel lubricity has decreased as a byproduct of reducing the sulfur levels in fuel. Contamination of fuel by water and debris is an ever-present problem. For oil-lubricated fuel system components, increased soot loading in the oil results in increased wear rates. Additionally, engine manufacturers are lengthening warranty periods for engines and systems. This combination of factors requires the development of new materials to counteract the harsher tribological environment.

  5. Pulsed laser kinetic studies of liquids under high pressure

    SciTech Connect (OSTI)

    Eyring, E.M.

    1992-09-22T23:59:59.000Z

    A laser flash photolysis kinetic study of 2,2{prime}-bipyridine bidentate chelating ligands with one claw in the first coordination sphere of a molybdenum carbonyl complex has been completed at pressures up to 150 MPa. The reaction mechanism for thermal ring closure is found from activation volumes to change from associative interchange to dissociative interchange as substituents on the 2,2{prime}-bipyridine ligands become bulkier. In a similar study of more rigid, substituted phenanthroline bidentate ligands it was found that substituent bulkiness had little effect on the thermal ring closure mechanism. Stability constants for lithium ion complexes with crown ethers in a room temperature molten salt, fluorescence quantum yields for cresyl violet and several other dyes in solution, and the oxidation of alcohols by OsO{sub 4} have also been investigated.

  6. Integrated-fin gasket for palm cubic-anvil high pressure apparatus

    SciTech Connect (OSTI)

    Cheng, J.-G. [Institute for Solid State Physics, University of Tokyo, 5-1-5 Kashiwanoha, Kashiwa, Chiba 277-8581 (Japan); Beijing National Laboratory for Condensed Matter Physics and Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China); Matsubayashi, K.; Nagasaki, S.; Hisada, A.; Hirayama, T.; Uwatoko, Y. [Institute for Solid State Physics, University of Tokyo, 5-1-5 Kashiwanoha, Kashiwa, Chiba 277-8581 (Japan); Hedo, M. [Faculty of Science, University of Ryukyus, Senbaru, Nishihara, Okinawa 903-0213 (Japan); Kagi, H. [Graduate School of Science, University of Tokyo, 7-3-1, Hongo Bunkyo-Ku, Tokyo 113-0033 (Japan)

    2014-09-15T23:59:59.000Z

    We described an integrated-fin gasket technique for the palm cubic-anvil apparatus specialized for the high-pressure and low-temperature measurements. By using such a gasket made from the semi-sintered MgO ceramics and the tungsten-carbide anvils of 2.5 mm square top, we successfully generate pressures over 16 GPa at both room and cryogenic temperatures down to 0.5 K. We observed a pressure self-increment for this specific configuration and further characterized the thermally induced pressure variation by monitoring the antiferromagnetic transition temperature of chromium up to 12 GPa. In addition to enlarge the pressure capacity, such a modified gasket also improves greatly the surviving rate of electrical leads hanging the sample inside a Teflon capsule filled with the liquid pressure-transmitting medium. These improvements should be attributed to the reduced extrusion of gasket materials during the initial compression.

  7. aluminum high pressure: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ALUMINUM OXIDE FOR THE SURFACE PASSIVATION OF HIGH-EFFICIENCY SILICON SOLAR CELLS Renewable Energy Websites Summary: ATOMIC-LAYER-DEPOSITED ALUMINUM OXIDE FOR...

  8. Microplasma Discharges in High Pressure Gases Scaling Towards the Sub-micron Regime

    E-Print Network [OSTI]

    Chitre, Aditya Rajeev

    2012-02-14T23:59:59.000Z

    Atmospheric pressure microplasmas are uniquely characterized by their very high energy densities and also by their small discharge sizes. These properties allow for unique applications in plasma processing technologies. We have investigated...

  9. FLOW OF A FLUID THROUGH A POROUS SOLID DUE TO HIGH PRESSURE GRADIENTS

    E-Print Network [OSTI]

    Bonito, Andrea

    or carbon diox- ide sequestration where very high pressure differentials are involved. Another important and geotechnical engineering, for example problems such as enhanced oil recovery and carbon di-oxide sequestration

  10. Radiochemical Transformation of High Pressure Methane under Gamma, Electron, and Neutron Irradiation

    E-Print Network [OSTI]

    Clemens, Jeffrey Tyler

    2014-05-01T23:59:59.000Z

    The chemical effects of irradiation on high pressure methane and noble gas mixtures were investigated using gamma, electron beam, and neutron irradiation sources. The gamma source used was the La-140 source from the Nuclear Science Center (NSC...

  11. ORIGINAL PAPER Titanium-and water-rich metamorphic olivine in high-pressure

    E-Print Network [OSTI]

    Jung, Haemyeong

    ORIGINAL PAPER Titanium- and water-rich metamorphic olivine in high-pressure serpentinites from 2013 Ó Springer-Verlag Berlin Heidelberg 2014 Abstract Titanium- and water-rich metamorphic olivine (Fo

  12. Design strategies for optimizing high burnup fuel in pressurized water reactors

    E-Print Network [OSTI]

    Xu, Zhiwen, 1975-

    2003-01-01T23:59:59.000Z

    This work is focused on the strategy for utilizing high-burnup fuel in pressurized water reactors (PWR) with special emphasis on the full array of neutronic considerations. The historical increase in batch-averaged discharge ...

  13. Consider Installing High-Pressure Boilers with Backpressure Turbine-Generators

    SciTech Connect (OSTI)

    Not Available

    2006-01-01T23:59:59.000Z

    This revised ITP tip sheet on installing high-pressure boilers provides how-to advice for improving industrial steam systems using low-cost, proven practices and technologies.

  14. Vapor-liquid equilibrium of water-acetone-air at ambient temperatures and pressures. An analysis of different VLE-fitting methods

    SciTech Connect (OSTI)

    Lichtenbelt, J.H.; Schram, B.J.

    1985-04-01T23:59:59.000Z

    The availability of accurate equilibrium data is of high importance in chemical engineering practice both for design and research purposes. It appeared that for the gas absorption system water-acetone-air in the range of special interest for absorption and desorption operations, neither literature data nor calculations following UNIFAC gave a sufficient accuracy. An experimental program was set up to determine equilibrium data with an accuracy within 2% for low acetone concentrations (up to 7 wt % gas phase) at ambient temperature (16-30/sup 0/C) and atmospheric pressure (740-860 mmHg). From experiments the activity coefficient at infinite dilution of acetone ..gamma.. is found to be 6.79 (0.01) at 20/sup 0/C and 7.28 (0.01) at 25/sup 0/C, while the total error in ..gamma.. is 1.5%. The equilibrium constant can be calculated from ..gamma.. and shows the same error. The experimental data-fitting with procedures of Margules (two parameters) and Van Laar were successful, but NRTL, Wilson, and UNIQUAC failed, probably because of the small concentration range used.

  15. Vehicle having hydraulic and power steering systems using a single high pressure pump

    DOE Patents [OSTI]

    Bartley, Bradley E. (Manito, IL); Blass, James R. (Bloomington, IL); Gibson, Dennis H. (Chillicothe, IL)

    2001-06-22T23:59:59.000Z

    A vehicle comprises a plurality of wheels attached to a vehicle housing. Also attached to the vehicle housing is a power steering system, including a fluid flow circuit, which is operably coupled to a number of the wheels. An internal combustion engine attached to the vehicle housing is connected to a hydraulically actuated system that includes a high pressure pump. An outlet of the high pressure pump is in fluid communication with the fluid flow circuit.

  16. Investigation of a high pressure implosive technique for metal powder compaction

    E-Print Network [OSTI]

    Garrett, Donald Richard

    1970-01-01T23:59:59.000Z

    INVESTIGATION OF A HIGH PRESSURE IMPLOSIVE TECHNIQUE FOR METAL POWDER COMPACTION A Thesis DONALD RICHARD GARRETT Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement for the degree of MASTER... OF SCIENCE August 1970 Ma)or Subject: Mechanical Engineering INVESTIGATION OF A HIGH PRESSURE IMPLOSIVE TECHNIQUE FOR METAL POWDER COMPACTION A Thesis by DONALD RICHARD GARRETT Approved as to style and content by: J@l, (Chairman of Committee) (Head...

  17. Innovative fuel designs for high power density pressurized water reactor

    E-Print Network [OSTI]

    Feng, Dandong, Ph. D. Massachusetts Institute of Technology

    2006-01-01T23:59:59.000Z

    One of the ways to lower the cost of nuclear energy is to increase the power density of the reactor core. Features of fuel design that enhance the potential for high power density are derived based on characteristics of ...

  18. A device for debridement using high pressure water jets

    E-Print Network [OSTI]

    Brown, Ashley (Ashley A.)

    2014-01-01T23:59:59.000Z

    Removing devitalized tissue from chronic wounds through debridement is critical to promote wound healing. In this thesis, technology using high-speed water jets is explored toward applications for debridement. After ...

  19. Design of high pressure metering and regulating stations

    SciTech Connect (OSTI)

    Rehler, D.A. [Oklahoma Natural Gas Co., Enid, OK (United States)

    1995-12-01T23:59:59.000Z

    Metering and regulating stations effectively serve as the cash registers of the natural gas industry. While the potential for lost revenue resulting from improper design is a serious consideration, it is not the only one. The potential exists for problems such as excessive noise levels, inaccurate reflection of lost and unaccounted-for gas, and numerous potentially hazardous situations. The best time to limit the potential for problems is during the design process. This, together with the critical nature of these stations, dictates that proper design is imperative. Proper design of metering and regulating stations is a constantly changing and extremely complicated subject. There are virtually an infinite number of situations that the designer can encounter in evaluating his design. In view of this, it is impossible to develop a cookbook method of designing these stations that covers all possible situations. The emphasis of this paper is to briefly touch on the major aspects of metering and regulating station design. Steps involved in station design are: 1. Collection of data on the proposed station. 2. Determination of piping configuration. 3. Selection of measurement equipment. 4. Selection of pressure regulating and overpressure protection equipment. 5. Communication of the final design to field personnel.

  20. Robofurnace: A semi-automated laboratory chemical vapor deposition system for high-throughput nanomaterial synthesis and process discovery

    SciTech Connect (OSTI)

    Oliver, C. Ryan; Westrick, William; Koehler, Jeremy; Brieland-Shoultz, Anna; Anagnostopoulos-Politis, Ilias; Cruz-Gonzalez, Tizoc [Department of Mechanical Engineering, University of Michigan, Ann Arbor, Michigan 48109 (United States)] [Department of Mechanical Engineering, University of Michigan, Ann Arbor, Michigan 48109 (United States); Hart, A. John, E-mail: ajhart@mit.edu [Department of Mechanical Engineering, University of Michigan, Ann Arbor, Michigan 48109 (United States); Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States)

    2013-11-15T23:59:59.000Z

    Laboratory research and development on new materials, such as nanostructured thin films, often utilizes manual equipment such as tube furnaces due to its relatively low cost and ease of setup. However, these systems can be prone to inconsistent outcomes due to variations in standard operating procedures and limitations in performance such as heating and cooling rates restrict the parameter space that can be explored. Perhaps more importantly, maximization of research throughput and the successful and efficient translation of materials processing knowledge to production-scale systems, relies on the attainment of consistent outcomes. In response to this need, we present a semi-automated lab-scale chemical vapor deposition (CVD) furnace system, called “Robofurnace.” Robofurnace is an automated CVD system built around a standard tube furnace, which automates sample insertion and removal and uses motion of the furnace to achieve rapid heating and cooling. The system has a 10-sample magazine and motorized transfer arm, which isolates the samples from the lab atmosphere and enables highly repeatable placement of the sample within the tube. The system is designed to enable continuous operation of the CVD reactor, with asynchronous loading/unloading of samples. To demonstrate its performance, Robofurnace is used to develop a rapid CVD recipe for carbon nanotube (CNT) forest growth, achieving a 10-fold improvement in CNT forest mass density compared to a benchmark recipe using a manual tube furnace. In the long run, multiple systems like Robofurnace may be linked to share data among laboratories by methods such as Twitter. Our hope is Robofurnace and like automation will enable machine learning to optimize and discover relationships in complex material synthesis processes.

  1. DEVELOPMENT OF ASME SECTION X CODE RULES FOR HIGH PRESSURE COMPOSITE HYDROGEN PRESSURE VESSELS WITH NON-LOAD SHARING LINERS

    SciTech Connect (OSTI)

    Rawls, G.; Newhouse, N.; Rana, M.; Shelley, B.; Gorman, M.

    2010-04-13T23:59:59.000Z

    The Boiler and Pressure Vessel Project Team on Hydrogen Tanks was formed in 2004 to develop Code rules to address the various needs that had been identified for the design and construction of up to 15000 psi hydrogen storage vessel. One of these needs was the development of Code rules for high pressure composite vessels with non-load sharing liners for stationary applications. In 2009, ASME approved new Appendix 8, for Section X Code which contains the rules for these vessels. These vessels are designated as Class III vessels with design pressure ranging from 20.7 MPa (3,000 ps)i to 103.4 MPa (15,000 psi) and maximum allowable outside liner diameter of 2.54 m (100 inches). The maximum design life of these vessels is limited to 20 years. Design, fabrication, and examination requirements have been specified, included Acoustic Emission testing at time of manufacture. The Code rules include the design qualification testing of prototype vessels. Qualification includes proof, expansion, burst, cyclic fatigue, creep, flaw, permeability, torque, penetration, and environmental testing.

  2. High Pressure Hydrogen Tank Manufacturing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the.pdfBreaking of Blythe Solar Power ProjectHawai'iPresentedHighHigh Performance

  3. High-Pressure MOF Research Yields Structural Insights

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh School football High School football FancyDepartment

  4. High-Pressure MOF Research Yields Structural Insights

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh School football High School football

  5. High Pressure PEM Electrolysis: Status, Key Issues, and Challenges

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(Fact Sheet), GeothermalGridHYDROGEN TOTechnologyHighLouisianaDepartmentHigh

  6. THE PLASMA WINDOW: A WINDOWLESS HIGH PRESSURE VACUUM INTERFACE FOR VARIOUS ACCELERATOR APPLICATIONS.

    SciTech Connect (OSTI)

    HERSHCOVITCH,A.I.; JOHNSON,E.D.; LANZA,R.C.

    1999-03-29T23:59:59.000Z

    The Plasma Window is a stabilized plasma arc used as an interface between accelerator vacuum and pressurized targets. There is no solid material introduced into the beam and thus it is also capable of transmitting particle beams and electromagnetic radiation with low loss and of sustaining high beam currents without damage. Measurements on a prototype system with a 3 mm diameter opening have shown that pressure differences of more than 2.5 atmospheres can be sustained with an input pressure of {approx} 10{sup -6} Torr. The system is capable of scaling to higher-pressure differences and larger apertures. Various plasma window applications for synchrotron light sources, high power lasers, internal targets, high current accelerators such as the HAWK, ATW, APT, DARHT, spallation sources, as well as for a number of commercial applications, will be discussed.

  7. Behavior of a hollow core photonic crystal fiber under high radial pressure for downhole application

    SciTech Connect (OSTI)

    Sadeghi, J., E-mail: j-sadeghi@sbu.ac.ir; Chenari, Z.; Ziaee, F. [Laser and Plasma Research Institute, Shahid Beheshti University, 1983963113 Tehran (Iran, Islamic Republic of); Latifi, H., E-mail: latifi@sbu.ac.ir [Laser and Plasma Research Institute, Shahid Beheshti University, 1983963113 Tehran (Iran, Islamic Republic of); Department of Physics, Shahid Beheshti University, Evin, 1983963113 Tehran (Iran, Islamic Republic of); Santos, J. L., E-mail: josantos@fc.up.pt [INESC Porto—Instituto de Engenharia de Sistemas e Computadores do Porto, Rua do Campo Alegre, 687, 4169-007 Porto (Portugal); Departamento de Física, da Faculdade de Ciências, da Universidade do Porto, Rua do Campo Alegre, 687, 4169-007 Porto (Portugal)

    2014-02-17T23:59:59.000Z

    Pressure fiber sensors play an important role in downhole high pressure measurements to withstand long term operation. The purpose of this paper is to present an application of hollow core photonic crystal fiber (HC-PCF) as a high pressure sensor head for downhole application based on dispersion variation. We used a high pressure stainless steel unit to exert pressure on the sensor. The experimental results show that different wavelengths based on sagnac loop interferometer have additive sensitivities from 5?×?10{sup ?5}?nm/psi at 1480?nm to 1.3?×?10{sup ?3}?nm/psi at 1680?nm. We developed a simulation to understand the reason for difference in sensitivity of wavelengths and also the relationship between deformation of HC-PCF and dispersion variation under pressure. For this purpose, by using the finite element method, we investigated the effect of structural variation of HC-PCF on spectral transformation of two linear polarizations under 1000?psi pressure. The simulation and experimental results show exponential decay behavior of dispersion variation from ?3.4?×?10{sup ?6} 1/psi to ?1.3?×?10{sup ?6} 1/psi and from ?5?×?10{sup ?6} 1/psi to ?1.8?×?10{sup ?6} 1/psi, respectively, which were in a good accordance with each other.

  8. Predictive modeling and high-pressure-high-temperature synthesis of perovskites containing monovalent silver

    SciTech Connect (OSTI)

    Park, J.H.; Parise, J.B. [State Univ. of New York, Stony Brook, NY (United States)] [State Univ. of New York, Stony Brook, NY (United States); Woodward, P.M. [Brookhaven National Lab., Upton, NY (United States). Physics Dept.] [Brookhaven National Lab., Upton, NY (United States). Physics Dept.

    1998-10-01T23:59:59.000Z

    The program POTATO, which was developed to model distorted perovskite structures, has been used to assess the stability of hypothetical compositions and guide the synthesis of new materials at high pressures and high temperatures. The initial result of this effort is the synthesis of two new perovskites, Ca{sub 2}NdAgTi{sub 4}O{sub 12} and NdAgTi{sub 2}O{sub 6}, which were synthesized at 14--14.5 GPa and 1000 C using the uniaxial split sphere anvil type press (USSA-2000). Both compounds are perovskites distorted from the ideal cubic structure by octahedral tilting distortions. Ca{sub 2}NdAgTi{sub 4}O{sub 12} contains a random distribution of Ca{sup 2+}/Nd{sup 3+}/Ag{sup +} ions on the A-site, whereas NdAgTi{sub 2}O{sub 6} has a partially ordered distribution of Nd{sup 3+}/Ag{sup +} ions. Ca{sub 2}NdAgTi{sub 4}O{sub 12} adopts the GdFeO{sub 3} structure. NdAgTi{sub 2}O{sub 6} belongs to the tetragonal space group P4/nbm. This structure can be derived from the simple cubic perovskite structure by rotations of the octahedra about the c-axis and partial ordering of Nd{sup 3+} and Ag{sup +} ions into alternating layers, perpendicular to the c-axis.

  9. High Pressure Hydrogen Storage in Carbon Nanotubes - Energy Innovation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cn SunnybankD.jpgHanfordDepartmentInnovationHigh FluxPerformancngPortal

  10. Improved Growth of High-Temperature Superconductors with HF Pressure

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh School footballHydrogenIT |HotImpactControl - Energy Innovation

  11. High Pressure Hydrogen Tank Manufacturing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(Fact Sheet), GeothermalGridHYDROGEN TOTechnologyHighLouisianaDepartment

  12. Boron nitrides synthesized directly from the elements at high pressures and temperatures

    SciTech Connect (OSTI)

    Nicol, M.; Yoo, C.S.; Akella, J.; Cynn, H.

    1996-11-01T23:59:59.000Z

    We use angle-resolved synchrotron x-ray diffraction, laser sample heating, and diamond-anvil cells to follow in-situ chemical reactions directly between elemental boron and nitrogen. The structures of the solid reaction products vary with pressure. Below 10 GPa, hexagonal BN is the product; cubic or wurzite BN form at higher pressures. Under nitrogen-rich conditions, another hexagonal allotrope occurs which seems to be a new highly transparent, low density h`-BN. No direct reactions occur at ambient temperature even at pressures as high as 50 GPa, implying that a large activation barrier limits the kinetics of these exothermic processes. Laser heating overcomes the large kinetic activation barrier and initiates spontaneous, self-sustaining exothermic reactions even at moderate pressures.

  13. Systematic prediction of high-pressure melting curves of transition metals

    SciTech Connect (OSTI)

    Hieu, Ho Khac, E-mail: hieuhk@duytan.edu.vn [Institute of Research and Development, Duy Tan University, K7/25 Quang Trung, Danang (Viet Nam)

    2014-10-28T23:59:59.000Z

    The pressure effects on melting temperatures of transition metals have been studied based on the combination of the modified Lindemann criterion with statistical moment method in quantum statistical mechanics. Numerical calculations have been performed for five transition metals including Cu, Pd, Pt, Ni, and Mn up to pressure 100?GPa. Our results are in good and reasonable agreements with available experimental data. This approach gives us a relatively simple method for qualitatively calculating high-pressure melting temperature. Moreover, it can be used to verify future experimental and theoretical works. This research proposes the potential of the combination of statistical moment method and the modified Lindemann criterion on predicting high-pressure melting of materials.

  14. Progress Report for UNLV High Pressure Science and Engineering Center

    SciTech Connect (OSTI)

    Mailhiot, C.; Pepper, D.; Lindle, D.; Nicol, M.

    1998-11-20T23:59:59.000Z

    In this report we present results of an in-depth analysis of the SP error densities for 29 satellites. These satellites were divided into three groups--Low Earth Orbit (LEO), Near Circular Orbit (NCO) and Highly Eccentric Orbit (HEO). Included in the first group were those satellites with eccentricities of less than 0.2 and perigees below 450km. The second group included satellites in near circular orbits (eccentricities of less than 0.015) and perigees from 700km to 1500km. The third group consisted of those satellites that were in highly eccentric orbits, namely those with eccentricities greater than 0.2. These satellites have perigees far into the thermosphere. Table 1 contains a summary of the orbit characteristics for the 29 satellites. In our study we attempted to unravel and elucidate the networks of relationships above. The satellite groupings and the report are organized in a way that reflects these efforts. We begin in Section 2 with a summary of the methods used in our analysis. One objective in this study was to establish a baseline for future work in satellite orbit propagators. Section 2 contains descriptions of the SP, truth orbits, and the satellite observation data used to establish this baseline. In the report we show how satellite error densities evolve in time up to thirty-six hours. We present error profiles, error histograms, rms errors and 95/9970 confidence limits for the along-track cross-track, and radial axes of motion for satellites in each of the three groupings. We present results of a regression analysis that establishes a physical model of the error densities. We also link the errors in the various regimes to the quality and quantity of the observational data.

  15. Stability analysis and testing of a train of centrifugal compressors for high pressure gas injection

    SciTech Connect (OSTI)

    Memmott, E.A. [Dresser-Rand Co., Olean, NY (United States)

    1999-07-01T23:59:59.000Z

    This paper describes the rotor dynamic stability analysis and the PTC-10 Class 1 test of a three body centrifugal compressor train for high pressure natural gas injection services. This train had a full load full pressure string test on hydrocarbon gases to a final discharge pressure of 500 BAR (7250 PSIA). Each compressor is of the back to back configuration, and is equipped with tilting pad seals, damper bearings, and a honeycomb labyrinth at the division wall with shunt holes. The driver is a gas turbine.

  16. An RF-only ion-funnel for extraction from high-pressure gases

    E-Print Network [OSTI]

    Thomas Brunner; Daniel Fudenberg; Victor Varentsov; Amanda Sabourov; Giorgio Gratta; Jens Dilling; Ralph DeVoe; David Sinclair; William Fairbank Jr.; Joshua B Albert; David J Auty; Phil S Barbeau; Douglas Beck; Cesar Benitez-Medina; Martin Breidenbach; Guofu F Cao; Christopher Chambers; Bruce Cleveland; Matthew Coon; Adam Craycraft; Timothy Daniels; Sean J Daugherty; Tamar Didberidze; Michelle J Dolinski; Matthew Dunford; Lorenzo Fabris; Jacques Farine; Wolfhart Feldmeier; Peter Fierlinger; Razvan Gornea; Kevin Graham; Mike Heffner; Mitchell Hughes; Michael Jewell; Xiaoshan S Jiang; Tessa N Johnson; Sereres Johnston; Alexander Karelin; Lisa J Kaufman; Ryan Killick; Thomas Koffas; Scott Kravitz; Reiner Kruecken; Alexey Kuchenkov; Krishna S Kumar; Douglas S Leonard; Francois Leonard; Caio Licciardi; Yi-Hsuan H Lin; Jiajie Ling; Ryan MacLellan; Michael G Marino; Brian Mong; David Moore; Allen Odian; Igor Ostrovskiy; Christian Ouellet; Andreas Piepke; Andrea Pocar; Fabrice Retiere; Peter C Rowson; Maria P Rozo; Alexis Schubert; Erica Smith; Victor Stekhanov; Michal Tarka; Tamer Tolba; Delia Tosi; Karl Twelker; Jean-Luc L Vuilleumier; Josiah Walton; Timothy Walton; Manuel Weber; Liangjian J Wen; Ubi Wichoski; Liang Yang; Yung-Ruey Yen

    2014-12-03T23:59:59.000Z

    An RF ion-funnel technique has been developed to extract ions from a high-pressure (10 bar) noble-gas environment into vacuum ($10^{-6}$ mbar). Detailed simulations have been performed and a prototype has been developed for the purpose of extracting $^{136}$Ba ions from Xe gas with high efficiency. With this prototype, ions have been extracted for the first time from high-pressure xenon gas and argon gas. Systematic studies have been carried out and compared to the simulations. This demonstration of extraction of ions with mass comparable to that of the gas generating the high-pressure into vacuum has applications to Ba tagging from a Xe-gas time-projection chamber (TPC) for double beta decay as well as to the general problem of recovering trace amounts of an ionized element in a heavy (m$>40$ u) carrier gas.

  17. Diffraction studies of order?disorder at high pressures and temperatures

    SciTech Connect (OSTI)

    Parise, John B.; Antao, Sytle M.; Martin, Charles D.; Crichton, Wilson (SBU); (ESRF)

    2008-06-18T23:59:59.000Z

    Recent developments at synchrotron X-ray beamlines now allow collection of data suitable for structure determination and Rietveld structure refinement at high pressures and temperatures on challenging materials. These include materials, such as dolomite (CaMg(CO{sub 3}){sub 2}) that tends to calcine at high temperatures, and Fe-containing materials, such as the spinel MgFe{sub 2}O{sub 4}, which tend to undergo changes in oxidation state. Careful consideration of encapsulation along with the use of radial collimation produced powder diffraction patterns virtually free of parasitic scattering from the cell in the case of large volume high-pressure experiments. These features have been used to study a number of phase transitions, especially those where superior signal-to-noise discrimination is required to distinguish weak ordering reflections. The structures adopted by dolomite, and CaSO4, anhydrite, were determined from 298 to 1466 K at high pressures. Using laser-heated diamond-anvil cells to achieve simultaneous high pressure and temperature conditions, we have observed CaSO{sub 4} undergo phase transitions to the monazite type and at highest pressure and temperature to crystallize in the barite-type structure. On cooling, the barite structure distorts, from an orthorhombic to a monoclinic lattice, to produce the AgMnO{sub 4}-type structure.

  18. Development of high temperature, high pressure rotating shaft seals: Final report

    SciTech Connect (OSTI)

    Heshmat, H.; Shapiro, W.

    1987-06-01T23:59:59.000Z

    Rotating shaft seals used in coal gasification equipment are exposed to difficult environmental conditions including temperature from 430/sup 0/C to 816/sup 0/C (800/sup 0/F to 1500/sup 0/F), high pressure (to 10 MPa or 1500 psig), and high levels of particulate contamination (50,000 to 100,000 ppM). The program reported upon was designed to develop long-life seals that would not require external flushing or cooling. The approach taken was to develop unbalanced face that would remain closed and prevent particulate entry into the interface. Wear resistant materials and coatings with low friction coefficients are required. Significant results of the program are enumerated: The selected material combination was a rotating runner of Kentanium K162B mating against a non-rotating seal ring of Kentanium K162B. Kentanium is the trade name of a series of hard carbide alloys with pure titanium carbide as the principal ingredient. Nickel and nickel molybdenum are used as binder materials. Kentanium retains most of its strength at temperatures ..mu..p to 1100/sup 0/C (2000/sup 0/F). Since hard materials are required to resist wear and withstand the temperatures, mechanical compliance must be built into the seal configuration for the opposed faces to follow runner nutations and remain closed. Environmental and frictional heating caused the formation of very small particles of titanium oxide which lodged in the face wave formations and acted as an interfacial lubricant. The results of this program provide encouragement and optimism that dry contact face seals can be developed for long unattended operation in the hostile environment of a coal gasification plant. 40 refs., 98 figs., 20 tabs.

  19. Development of a High Pressure/High Temperature Down-hole Turbine Generator

    SciTech Connect (OSTI)

    Ben Plamp

    2008-06-30T23:59:59.000Z

    As oil & natural gas deposits become more difficult to obtain by conventional means, wells must extend to deeper more heat-intensive environments. The technology of the drilling equipment required to reach these depths has exceeded the availability of electrical power sources needed to operate these tools. Historically, logging while drilling (LWD) and measure while drilling (MWD) devices utilized a wireline to supply power and communication from the operator to the tool. Lithium ion batteries were used in scenarios where a wireline was not an option, as it complicated operations. In current downhole applications, lithium ion battery (LIB) packs are the primary source for electrical power. LIB technology has been proven to supply reliable downhole power at temperatures up to 175 °C. Many of the deeper well s reach ambient temperatures above 200 °C, creating an environment too harsh for current LIB technology. Other downfalls of LIB technology are cost, limitations on charge cycles, disposal issues and possible safety hazards including explosions and fires. Downhole power generation can also be achieved by utilizing drilling fluid flow and converting it to rotational motion. This rotational motion can be harnessed to spin magnets around a series of windings to produce power proportional to the rpm experienced by the driven assembly. These generators are, in most instances, driven by turbine blades or moyno-based drilling fluid pumps. To date, no commercially available downhole power generators are capable of operating at ambient temperatures of 250 °C. A downhole power g enerator capable of operation in a 250 °C and 20,000 psi ambient environment will be an absolute necessity in the future. Dexter Magnetic Technologies’ High-Pressure High-Temperature (HPHT) Downhole Turbine Generator is capable of operating at 250 °C and 20, 000 psi, but has not been tested in an actual drilling application. The technology exists, but to date no company has been willing to test the tool.

  20. High-pressure behavior of amorphous selenium from ultrasonic measurements and Raman spectroscopy

    SciTech Connect (OSTI)

    He, Z.; Liu, X. R.; Hong, S. M., E-mail: hpswjtu@gmail.com, E-mail: smhong@home.swjtu.edu.cn [Laboratory of High Pressure Physics, Southwest Jiaotong University, Key Laboratory of Advanced Technologies of Materials, Ministry of Education of China, Chengdu 610031 (China); Wang, Z. G. [National Key Laboratory for Shock Wave and Detonation Physics Research, Institute of Fluid Physics, Chinese Academy of Engineering Physics, Mianyang 621900 (China); Zhu, H. Y. [State Key Laboratory of Superhard Materials, Jilin University, Changchun 130012 (China); Peng, J. P. [School of Physical Science and Technology, Southwest Jiaotong University, Chengdu 610031 (China)

    2014-07-07T23:59:59.000Z

    The high-pressure behavior of melt-quenched amorphous selenium (a-Se) has been investigated via ultrasonic measurements and Raman scattering at room temperature. The ultrasonic measurements were conducted on a-Se in a multi-anvil apparatus with two different sample assemblies at pressures of up to 4.5 and 4.8?GPa. We discovered that similar kinks occur in the slopes of the pressure dependence characteristics of the travel time and the sound velocity in both shear and longitudinal waves in the 2.0–2.5?GPa range. These kinks are independent of the sample assemblies, indicating an intrinsic transformation of the a-Se. Additionally, we deduced the pressure-volume relationship of a-Se from the sound velocity characteristics using the Birch–Murnaghan equation of state, and the results agreed well with those of previous reports. In situ high-pressure Raman scattering measurements of a-Se were conducted in a diamond anvil cell with an 830?nm excitation line up to a pressure of 4.3?GPa. We found that the characteristic band of a-Se at ?250?cm{sup ?1} experienced a smooth shift to a lower frequency with pressure, but a sharp slope change in the band intensity versus pressure occurred near 2.5?GPa. The results of X-ray diffraction and differential scanning calorimetry measurements indicate that the samples remain in their amorphous states after decompression. Thus, we proposed that the abnormal compression behavior of a-Se in the 2.0–2.5?GPa range can be attributed to pressure-induced local atomic reconfiguration, implying an amorphous-amorphous transition of the elementary selenium.

  1. The Progress on Low-Cost, High-Quality, High-Temperature Superconducting Tapes Deposited by the Combustion Chemical Vapor Deposition Process

    SciTech Connect (OSTI)

    Shoup, S.S.; White, M.K.; Krebs, S.L.; Darnell, N.; King, A.C.; Mattox, D.S.; Campbell, I.H.; Marken, K.R.; Hong, S.; Czabaj, B.; Paranthaman, M.; Christen, H.M.; Zhai, H.-Y. Specht, E.

    2008-06-24T23:59:59.000Z

    The innovative Combustion Chemical Vapor Deposition (CCVD) process is a non-vacuum technique that is being investigated to enable next generation products in several application areas including high-temperature superconductors (HTS). In combination with the Rolling Assisted Biaxially Textured Substrate (RABiTS) technology, the CCVD process has significant promise to provide low-cost, high-quality lengths of YBCO coated conductor. Over 100 meter lengths of both Ni and Ni-W (3 at. Wt.%) substrates with a surface roughness of 12-18 nm were produced. The CCVD technology has been used to deposit both buffer layer coatings as well as YBCO superconducting layers. Buffer layer architecture of strontium titanate (SrTiO{sub 3}) and ceria (CeO{sub 2}) have been deposited by CCVD on textured nickel substrates and optimized to appropriate thicknesses and microstructures to provide templates for growing PLD YBCO with a J{sub c} of 1.1 MA/cm{sup 2} at 77 K and self-field. The CCVD buffer layers have been scaled to meter plus lengths with good epitaxial uniformity along the length. A short sample cut from one of the lengths enabled high critical current density PLD YBCO. Films of CCVD YBCO superconductors have been grown on single crystal substrates with critical current densities over 1 MA/cm{sup 2}. In addition, superconducting YBCO films with an I{sub c} of 60 A/cm-width (J{sub c} = 1.5 MA/cm{sup 2}) were grown on ORNL RABiTS (CeO{sub 2}/YSZ/Y{sub 2}O{sub 3}/Ni/Ni-3W) using CCVD process.

  2. Ex 7.6(a) The vapor pressure of benzene is 400 Torr at 60.6C, but it fell to 386 Torr when 19.0 g of an involatile organic compound was dissolved in 500 g of benzene. Calculate the

    E-Print Network [OSTI]

    Findley, Gary L.

    Ex 7.6(a) The vapor pressure of benzene is 400 Torr at 60.6°C, but it fell to 386 Torr when 19.0 g of an involatile organic compound was dissolved in 500 g of benzene. Calculate the molar mass of the involatile

  3. Dielectric Spectroscopy and Ultrasonic Study of Propylene Carbonate under Ultra-high Pressures

    E-Print Network [OSTI]

    M. V. Kondrin; E. L. Gromnitskaya; A. A. Pronin; A. G. Lyapin; V. V. Brazhkin; A. A. Volkov

    2013-05-16T23:59:59.000Z

    We present the high pressure dielectric spectroscopy (up to 4.2 GPa) and ultrasonic study (up to 1.7 GPa) of liquid and glassy propylene carbonate (PC). Both of the methods provide complementary pictures of the glass transition in PC under pressure. No other relaxation processes except $\\alpha$-relaxation have been found in the studied pressure interval. The propylene carbonate liquid is a glassformer where simple relaxation and the absence of $\\beta$-relaxation are registered in the record-breaking ranges of pressures and densities. The equation of state of liquid PC was extended up to 1 GPa from ultrasonic measurements of bulk modulus and is in good accordance with the previous equations developed from volumetric data. We measured the bulk and shear moduli and Poisson's ratio of glassy PC up to 1.7 GPa. Many relaxation and elastic properties of PC can be qualitatively described by the soft-sphere or Lennard-Jones model. However, for the quantitative description of entire set of the experimental data, these models are insufficient. Moreover, the Poisson coefficient value for glassy PC indicates a significant contribution of non-central forces to the intermolecular potential. The well-known correlation between Poisson's ratio and fragility index (obtained from dielectric relaxation) is confirmed for PC at ambient pressure, but it is violated with pressure increase. This indicates that different features of the potential energy landscape are responsible for the evolution of dielectric response and elasticity with pressure increase.

  4. High-resolution thermal expansion measurements under helium-gas pressure

    SciTech Connect (OSTI)

    Manna, Rudra Sekhar; Wolf, Bernd; Souza, Mariano de; Lang, Michael [Physics Institute, Goethe University Frankfurt(M), SFB/TR49, D-60438 Frankfurt am Main (Germany)

    2012-08-15T23:59:59.000Z

    We report on the realization of a capacitive dilatometer, designed for high-resolution measurements of length changes of a material for temperatures 1.4 K Less-Than-Or-Slanted-Equal-To T Less-Than-Or-Slanted-Equal-To 300 K and hydrostatic pressure P Less-Than-Or-Slanted-Equal-To 250 MPa. Helium ({sup 4}He) is used as a pressure-transmitting medium, ensuring hydrostatic-pressure conditions. Special emphasis has been given to guarantee, to a good approximation, constant-pressure conditions during temperature sweeps. The performance of the dilatometer is demonstrated by measurements of the coefficient of thermal expansion at pressures P Asymptotically-Equal-To 0.1 MPa (ambient pressure) and 104 MPa on a single crystal of azurite, Cu{sub 3}(CO{sub 3}){sub 2}(OH){sub 2}, a quasi-one-dimensional spin S = 1/2 Heisenberg antiferromagnet. The results indicate a strong effect of pressure on the magnetic interactions in this system.

  5. Effect of high pressure homogenization on aqueous phase solvent extraction of lipids from Nannochloris Oculata microalgae

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Samarasinghe, Nalin; Fernando, Sandun; Faulkner, William B.

    2012-01-01T23:59:59.000Z

    The ability to extract lipids from high-moisture Nannochloris Oculata algal biomass disrupted with high pressure homogenization was investigated. During the first phase, the effect of high pressure homogenization (system pressure and number of passes) on disrupting aqueous algae (of different concentrations and degree of stress) was investigated. Secondly, the effect of degree of cell wall disruption on the amount of lipids extracted with three solvents, namely: hexane, dichloromethane and chloroform, were compared. Studies reveled that high pressure homogenization is effective on cell disruption while the amount of system pressure being the most significant factor affecting the degree of cell breakage.more »Although the number of passes had some impact, the level of disruption seemed to level-off after a certain number of passes. The study revealed that slightly polar solvents (such as chloroform and dichloromethane) performed better in aqueous-phase lipid extractions as compared to hexane. Also, it was revealed that it was not necessary to disrupt the algal cells completely to achieve appreciable levels of lipid yields. In fact, conditions that exerted only 20% of the cells to completely disrupt, allowed sufficient damage to liberate most of the lipids contained in the remainder of the cells.« less

  6. Revisit of the relationship between the elastic properties and sound velocities at high pressures

    SciTech Connect (OSTI)

    Wang, Chenju; Yan, Xiaozhen [National Key Laboratory of Shock Wave and Detonation Physics, Institute of Fluid Physics, PO Box 919-102, Mianyang, Sichuan 621900 (China); Institute of Atomic and Molecular Sciences, Sichuan University, Chengdu 610065 (China); Xiang, Shikai, E-mail: skxiang@caep.ac.cn; Chen, Haiyan [National Key Laboratory of Shock Wave and Detonation Physics, Institute of Fluid Physics, PO Box 919-102, Mianyang, Sichuan 621900 (China); Gu, Jianbing; Yu, Yin [National Key Laboratory of Shock Wave and Detonation Physics, Institute of Fluid Physics, PO Box 919-102, Mianyang, Sichuan 621900 (China); College of Physical Science and Technology, Sichuan University, Chengdu 610064 (China); Kuang, Xiaoyu [Institute of Atomic and Molecular Sciences, Sichuan University, Chengdu 610065 (China); International Centre for Materials Physics, Academia Sinica, Shenyang 110016 (China)

    2014-09-14T23:59:59.000Z

    The second-order elastic constants and stress-strain coefficients are defined, respectively, as the second derivatives of the total energy and the first derivative of the stress with respect to strain. Since the Lagrangian and infinitesimal strain are commonly used in the two definitions above, the second-order elastic constants and stress-strain coefficients are separated into two categories, respectively. In general, any of the four physical quantities is employed to characterize the elastic properties of materials without differentiation. Nevertheless, differences may exist among them at non-zero pressures, especially high pressures. Having explored the confusing issue systemically in the present work, we find that the four quantities are indeed different from each other at high pressures and these differences depend on the initial stress applied on materials. Moreover, the various relations between the four quantities depicting elastic properties of materials and high-pressure sound velocities are also derived from the elastic wave equations. As examples, we calculated the high-pressure sound velocities of cubic tantalum and hexagonal rhenium using these nexus. The excellent agreement of our results with available experimental data suggests the general applicability of the relations.

  7. Effect of high pressure homogenization on aqueous phase solvent extraction of lipids from Nannochloris Oculata microalgae

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Samarasinghe, Nalin [Texas A & M Univ., College Station, TX (United States). Dept. of Biological and Agricultural Engineering; Fernando, Sandun [Texas A & M Univ., College Station, TX (United States). Dept. of Biological and Agricultural Engineering; Faulkner, William B. [Texas A & M Univ., College Station, TX (United States). Dept. of Biological and Agricultural Engineering

    2012-01-01T23:59:59.000Z

    The ability to extract lipids from high-moisture Nannochloris Oculata algal biomass disrupted with high pressure homogenization was investigated. During the first phase, the effect of high pressure homogenization (system pressure and number of passes) on disrupting aqueous algae (of different concentrations and degree of stress) was investigated. Secondly, the effect of degree of cell wall disruption on the amount of lipids extracted with three solvents, namely: hexane, dichloromethane and chloroform, were compared. Studies reveled that high pressure homogenization is effective on cell disruption while the amount of system pressure being the most significant factor affecting the degree of cell breakage. Although the number of passes had some impact, the level of disruption seemed to level-off after a certain number of passes. The study revealed that slightly polar solvents (such as chloroform and dichloromethane) performed better in aqueous-phase lipid extractions as compared to hexane. Also, it was revealed that it was not necessary to disrupt the algal cells completely to achieve appreciable levels of lipid yields. In fact, conditions that exerted only 20% of the cells to completely disrupt, allowed sufficient damage to liberate most of the lipids contained in the remainder of the cells.

  8. Numerical investigation of high-pressure combustion in rocket engines using Flamelet/Progress-variable models

    E-Print Network [OSTI]

    Coclite, A; De Palma, P; Pascazio, G

    2015-01-01T23:59:59.000Z

    The present paper deals with the numerical study of high pressure LOx/H2 or LOx/hydrocarbon combustion for propulsion systems. The present research effort is driven by the continued interest in achieving low cost, reliable access to space and more recently, by the renewed interest in hypersonic transportation systems capable of reducing time-to-destination. Moreover, combustion at high pressure has been assumed as a key issue to achieve better propulsive performance and lower environmental impact, as long as the replacement of hydrogen with a hydrocarbon, to reduce the costs related to ground operations and increase flexibility. The current work provides a model for the numerical simulation of high- pressure turbulent combustion employing detailed chemistry description, embedded in a RANS equations solver with a Low Reynolds number k-omega turbulence model. The model used to study such a combustion phenomenon is an extension of the standard flamelet-progress-variable (FPV) turbulent combustion model combined ...

  9. Stages of destruction and elastic compression of granular nanoporous carbon medium at high pressures

    E-Print Network [OSTI]

    I. M. Neklyudov; O. P. Ledenyov; N. B. Bobrova; A. A. Chupikov

    2015-05-14T23:59:59.000Z

    The granular nanoporous carbon medium, made of the cylindrical coal granules of the adsorbent of SKT 3, at an influence by the high pressures from 1MPa to 3GPa has been researched. The eight consecutive stages of the materials specific volume change, which is characterized by a certain dependence of the volume change on the pressure change, have been registered. It is shown that there is a linear dependence on the double log log plot of the materials specific volume change on the pressure for an every stage of considered process. The two stages are clearly distinguished such as a stage of materials mechanical destruction, and a stage of elastic compression of material without the disintegration of structure at a nanscale. The hysteresis dependence of the materials specific volume change on the pressure change at the pressure decrease is observed. The small disperse coal dust particles jettisoning between the high pressure cell and the base plate was observed, resulting in the elastic stress reduction in relation to the small disperse coal dust particles volume. The obtained research data can be used to improve the designs of air filters for the radioactive chemical elements absorption at the NPP with the aims to protect the environment.

  10. A primary high-pressure air flow measurement standard in Taiwan

    SciTech Connect (OSTI)

    Jiunn-Haur Shaw; Fong-Ruey Yang; Yao-Fu Chen [Industrial Technology Research Inst., Hsinchu (Taiwan, Province of China)

    1995-12-31T23:59:59.000Z

    A high-pressure air-flow national measurement standard is constructed in Taiwan with a capacity of 8400 Nm{sup 3}/h and a projected measurement uncertainty of {plus_minus}0.2% in the pressure range of 1 {approximately} 84 bars. it is a blow-down type facility, and its main purpose is to serve as the primary standard of a larger-flowrate natural gas flow measurement facility to be built in the future by Chinese Petroleum Company (CPC). The system has a gyroscopic weighing platform suitable for high precision gravimetric measurements and several sonic nozzles with different throat diameters situated in a chamber to be the reference flow meters. A set of two turbine meters, 50mm and 100mm, are sued as the transfer standard. The facility has two test sections separated by the nozzle chamber and four different calibration modes could be arranged. To make calibration, the storage tank, the temperature control loop, and two sets of pressure regulating valve establish a pressurized air flow with stable temperature and pressure in the test section. The control of the air-flow diversion, connect-disconnect mechanism, sonic nozzle array is made through a hydraulic power unit operating at 200 bars. Real time measurements of temperature, pressure, flow signal, and time are collected through a Honeywell 9000-series PLC and a FIX DMAC data acquisition/control software. This paper describes the key components of the test facility and presents the preliminary results of performance assessment.

  11. Detecting and modeling cement failure in high pressure/ high temperature wells using finite-element method

    E-Print Network [OSTI]

    Shahri, Mehdi Abbaszadeh

    2006-04-12T23:59:59.000Z

    conditions and are investigated simultaneously to more accurately predict cement failure. The results of this study show the relevant dependency of stress principles with temperature and pressure. These results clarify the deformation caused by any...

  12. Improved x-ray collimation system for diamond-anvil high-pressure cells

    SciTech Connect (OSTI)

    Schiferl, D.; Olinger, B.; Livingston, R.

    1983-09-01T23:59:59.000Z

    An improved x-ray collimation system for diamond-anvil high-pressure cells is described. The usual practice of mounting the collimator directly in the diamond-anvil cell is not followed. Instead, the collimator is mounted and aligned in a fixture which can be removed from the diamong-anvil cell. The end of the collimator furthest from the sample can be fitted with a set of removable plugs, each with a different aperture. This collimation system is easily aligned, can be removed from the high-pressure cell with no loss of alignment, and is inexpensive to construct.

  13. Structural changes in nano-crystalline mackinawite (FeS) at high - pressure.

    SciTech Connect (OSTI)

    Ehm, L.; Michael, F. M.; Antao, S. M.; Martin, C. D.; Lee, P. L.; Shastri, S. D.; Chupas, P. J.; Parise, J. B.; Stony Brook Univ.

    2009-02-01T23:59:59.000Z

    The high-pressure behavior of nanocrystalline mackinawite (FeS) with particle sizes of 6, 7 and 8 nm has been investigated by high-energy X-ray total scattering and pair distribution function analysis. An irreversible first-order structural phase transition from tetragonal mackinawite to orthorhombic FeS-II was observed at about 3 GPa. The transition is induced by the closure of the van der Waals gap in the layered mackinawite structure. A grain size effect on the transition pressure and the compressibility was observed.

  14. High-pressure powder x-ray diffraction study of EuVO4

    E-Print Network [OSTI]

    Garg, Alka B

    2015-01-01T23:59:59.000Z

    The high-pressure structural behavior of europium orthovanadate has been studied using in-situ, synchrotron based, high-pressure x-ray powder diffraction technique. Angle-dispersive x-ray diffraction measurements were carried out at room temperature up to 34.7 GPa using a diamond-anvil cell, extending the pressure range reported in previous experiments. We confirmed the occurrence of zircon-scheelite phase transition at 6.8 GPa and the coexistence of low- and high-pressure phases up to 10.1 GPa. In addition, clear evidence of a scheelite-fregusonite transition is found at 23.4 GPa. The fergusonite structure remains stable up to 34.7 GPa, the highest pressure reached in the present measurements. A partial decomposition of EuVO4 was also observed from 8.1 to 12.8 GPa, however, this fact did not preclude the identification of the different crystal structures of EuVO4. The crystal structures of the different phases have been Rietveld refined and their equations of state (EOS) have been determined. The results are...

  15. Rotor Design for High Pressure Magic Angle Spinning Nuclear Magnetic Resonance

    SciTech Connect (OSTI)

    Turcu, Romulus V.F.; Hoyt, David W.; Rosso, Kevin M.; Sears, Jesse A.; Loring, John S.; Felmy, Andrew R.; Hu, Jian Z.

    2013-01-01T23:59:59.000Z

    High pressure magic angle spinning (MAS) nuclear magnetic resonance (NMR) with a sample spinning rate exceeding 2.1 kHz and pressure greater than 165 bar has never been realized. In this work, a new sample cell design is reported, suitable for constructing cells of different sizes. Using a 7.5 mm high pressure MAS rotor as an example, internal pressure as high as 200 bar at a sample spinning rate of 6 kHz is achieved. The new high pressure MAS rotor is re-usable and compatible with most commercial NMR set-ups, exhibiting low 1H and 13C NMR background and offering maximal NMR sensitivity. As an example of its many possible applications, this new capability is applied to determine reaction products associated with the carbonation reaction of a natural mineral, antigorite ((Mg,Fe2+)3Si2O5(OH)4), in contact with liquid water in water-saturated supercritical CO2 (scCO2) at 150 bar and 50 deg C. This mineral is relevant to the deep geologic disposal of CO2, but its iron content results in too many sample spinning sidebands at low spinning rate. Hence, this chemical system is a good case study to demonstrate the utility of the higher sample spinning rates that can be achieved by our new rotor design. We expect this new capability will be useful for exploring solid-state, including interfacial, chemistry at new levels of high-pressure in a wide variety of fields.

  16. Coupling apparatus for a metal vapor laser

    DOE Patents [OSTI]

    Ball, Don G. (Livermore, CA); Miller, John L. (Dublin, CA)

    1993-01-01T23:59:59.000Z

    Coupling apparatus for a large bore metal vapor laser is disclosed. The coupling apparatus provides for coupling high voltage pulses (approximately 40 KV) to a metal vapor laser with a high repetition rate (approximately 5 KHz). The coupling apparatus utilizes existing thyratron circuits and provides suitable power input to a large bore metal vapor laser while maintaining satisfactory operating lifetimes for the existing thyratron circuits.

  17. Coupling apparatus for a metal vapor laser

    DOE Patents [OSTI]

    Ball, D.G.; Miller, J.L.

    1993-02-23T23:59:59.000Z

    Coupling apparatus for a large bore metal vapor laser is disclosed. The coupling apparatus provides for coupling high voltage pulses (approximately 40 KV) to a metal vapor laser with a high repetition rate (approximately 5 KHz). The coupling apparatus utilizes existing thyratron circuits and provides suitable power input to a large bore metal vapor laser while maintaining satisfactory operating lifetimes for the existing thyratron circuits.

  18. Elastic properties, sp{sup 3} fraction, and Raman scattering in low and high pressure synthesized diamond-like boron rich carbides

    SciTech Connect (OSTI)

    Zinin, Pavel V.; Burgess, Katherine; Jia, Ruth; Sharma, Shiv; Ming, Li-Chung [Hawaii Institute of Geophysics and Planetology, University of Hawaii, Honolulu, Hawaii 96822 (United States); Liu, Yongsheng [Science and Technology on Thermostructure Composite Materials Laboratory, Northwestern Polytechnical University, Xi'an Shanxi (China); Ciston, Jim [National Center for Electron Microscopy, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Hong, Shiming [Laboratory of High Pressure Physics, Southwest Jiaotong University, Chengdu, Sichuan (China)

    2014-10-07T23:59:59.000Z

    Dense BC{sub x} phases with high boron concentration are predicted to be metastable, superhard, and conductors or superconductors depending on boron concentration. However, up to this point, diamond-like boron rich carbides BC{sub x} (dl-BC{sub x}) phases have been thought obtainable only through high pressure and high temperature treatment, necessitating small specimen volume. Here, we use electron energy loss spectroscopy combined with transmission electron microscopy, Raman spectroscopy, surface Brillouin scattering, laser ultrasonics (LU) technique, and analysis of elastic properties to demonstrate that low pressure synthesis (chemical vapor deposition) of BC{sub x} phases may also lead to the creation of diamond-like boron rich carbides. The elastic properties of the dl-BC{sub x} phases depend on the carbon sp{sup 2} versus sp{sup 3} content, which decreases with increasing boron concentration, while the boron bonds determine the shape of the Raman spectra of the dl-BC{sub x} after high pressure-high temperature treatment. Using the estimation of the density value based on the sp{sup 3} fraction, the shear modulus ? of dl-BC{sub 4}, containing 10% carbon atoms with sp{sup 3} bonds, and dl-B{sub 3}C{sub 2}, containing 38% carbon atoms with sp{sup 3} bonds, were found to be ??=?19.3?GPa and ??=?170?GPa, respectively. The presented experimental data also imply that boron atoms lead to a creation of sp{sup 3} bonds during the deposition processes.

  19. Properties of molecular solids and fluids at high pressure and temperatures

    SciTech Connect (OSTI)

    Etters, R.D.

    1992-03-01T23:59:59.000Z

    This renewal request for DOE grant DE-FG02-86ER45238, is dedicated to providing a complete thermodynamic profile of solids fluids, and fluid mixtures, over a wide range of temperatures and pressures. We are partially motivated by technological interest in detonation, combustion, superhard high pressure materials, and high temperature superconductors, which are important components of interest of various DOE laboratories. Our work on fluids and solids, composed of simple molecules, involves the determination of structures, phase transitions, pressure-volume relations, phonon, vibron, and libron modes of excitation, sound velocities, specific heats, thermal expansion, virial coefficients, sublimation energies, and orientational translational, and magnetic correlations. We hope that the study of these systems under extreme thermodynamic conditions will lead to exotic new materials of value, as well as enhanced fundamental understanding.

  20. A cryogenic high pressure cell for inelastic neutron scattering measurements of quantum fluids and solids

    SciTech Connect (OSTI)

    Carmichael, Justin R [ORNL; Omar Diallo, Souleymane [ORNL

    2013-01-01T23:59:59.000Z

    We present our new development of a high pressure cell for inelastic neutron scattering measurements of helium at ultra-low temperatures. The cell has a large sample volume of ~140 cm3, and a working pressure of ~70 bar, with a relatively thin wall-thickness (1.1 mm) - thanks to the high yield strength aluminum used in the design. Two variants of this cell have been developed; one with permanently joined components using electron-beam welding and explosion welding, methods that have little or no impact on the global heat treatment of the cell, and another with modular and interchangeable components, which include a capacitance pressure gauge, that can be sealed using traditional indium wire technique. The performance of the cell has been tested in recent measurements on superfluid liquid helium near the solidification line.

  1. Automated High-Pressure Titration System with In Situ Infrared Spectroscopic Detection

    SciTech Connect (OSTI)

    Thompson, Christopher J.; Martin, Paul F.; Chen, Jeffrey; Benezeth, Pascale; Schaef, Herbert T.; Rosso, Kevin M.; Felmy, Andrew R.; Loring, John S.

    2014-04-17T23:59:59.000Z

    A fully automated titration system with infrared detection was developed for investigating interfacial chemistry at high pressures. The apparatus consists of a high-pressure fluid generation and delivery system coupled to a high-pressure cell with infrared optics. A manifold of electronically actuated valves is used to direct pressurized fluids into the cell. Precise reagent additions to the pressurized cell are made with calibrated tubing loops that are filled with reagent and placed in-line with the cell and a syringe pump. The cell’s infrared optics facilitate both transmission and attenuated total reflection (ATR) measurements to monitor bulk-fluid composition and solid-surface phenomena such as adsorption, desorption, complexation, dissolution, and precipitation. Switching between the two measurement modes is accomplished with moveable mirrors that direct radiation from a Fourier transform infrared spectrometer into the cell along transmission or ATR light paths. The versatility of the high-pressure IR titration system is demonstrated with three case studies. First, we titrated water into supercritical CO2 (scCO2) to generate an infrared calibration curve and determine the solubility of water in CO2 at 50 °C and 90 bar. Next, we characterized the partitioning of water between a montmorillonite clay and scCO2 at 50 °C and 90 bar. Transmission-mode spectra were used to quantify changes in the clay’s sorbed water concentration as a function of scCO2 hydration, and ATR measurements provided insights into competitive residency of water and CO2 on the clay surface and in the interlayer. Finally, we demonstrated how time-dependent studies can be conducted with the system by monitoring the carbonation reaction of forsterite (Mg2SiO4) in water-bearing scCO2 at 50 °C and 90 bar. Immediately after water dissolved in the scCO2, a thin film of adsorbed water formed on the mineral surface, and the film thickness increased with time as the forsterite began to dissolve. However, after approximately 2.5 hours, the trend reversed, and a carbonate precipitate began to form on the forsterite surface, exposing dramatic chemical changes in the thin-water film. Collectively, these applications illustrate how the high-pressure IR titration system can provide molecular-level information about the interactions between variably wet scCO2 and minerals relevant to underground storage of CO2 (geologic carbon sequestration). The apparatus could also be utilized to study high-pressure interfacial chemistry in other areas such as catalysis, polymerization, food processing, and oil and gas recovery.

  2. Automated high-pressure titration system with in situ infrared spectroscopic detection

    SciTech Connect (OSTI)

    Thompson, Christopher J., E-mail: chris.thompson@pnnl.gov; Martin, Paul F.; Chen, Jeffrey; Schaef, Herbert T.; Rosso, Kevin M.; Felmy, Andrew R.; Loring, John S. [Pacific Northwest National Laboratory, Richland, Washington 99352 (United States)] [Pacific Northwest National Laboratory, Richland, Washington 99352 (United States); Benezeth, Pascale [Géosciences Environnement Toulouse (GET), CNRS-Université de Toulouse, 31400 Toulouse (France)] [Géosciences Environnement Toulouse (GET), CNRS-Université de Toulouse, 31400 Toulouse (France)

    2014-04-15T23:59:59.000Z

    A fully automated titration system with infrared detection was developed for investigating interfacial chemistry at high pressures. The apparatus consists of a high-pressure fluid generation and delivery system coupled to a high-pressure cell with infrared optics. A manifold of electronically actuated valves is used to direct pressurized fluids into the cell. Precise reagent additions to the pressurized cell are made with calibrated tubing loops that are filled with reagent and placed in-line with the cell and a syringe pump. The cell's infrared optics facilitate both transmission and attenuated total reflection (ATR) measurements to monitor bulk-fluid composition and solid-surface phenomena such as adsorption, desorption, complexation, dissolution, and precipitation. Switching between the two measurement modes is accomplished with moveable mirrors that direct the light path of a Fourier transform infrared spectrometer into the cell along transmission or ATR light paths. The versatility of the high-pressure IR titration system was demonstrated with three case studies. First, we titrated water into supercritical CO{sub 2} (scCO{sub 2}) to generate an infrared calibration curve and determine the solubility of water in CO{sub 2} at 50?°C and 90 bar. Next, we characterized the partitioning of water between a montmorillonite clay and scCO{sub 2} at 50?°C and 90 bar. Transmission-mode spectra were used to quantify changes in the clay's sorbed water concentration as a function of scCO{sub 2} hydration, and ATR measurements provided insights into competitive residency of water and CO{sub 2} on the clay surface and in the interlayer. Finally, we demonstrated how time-dependent studies can be conducted with the system by monitoring the carbonation reaction of forsterite (Mg{sub 2}SiO{sub 4}) in water-bearing scCO{sub 2} at 50?°C and 90 bar. Immediately after water dissolved in the scCO{sub 2}, a thin film of adsorbed water formed on the mineral surface, and the film thickness increased with time as the forsterite began to dissolve. However, after approximately 2.5 h, the trend reversed, and a carbonate precipitate began to form on the forsterite surface, exposing dramatic chemical changes in the thin-water film. Collectively, these applications illustrate how the high-pressure IR titration system can provide molecular-level information about the interactions between variably wet scCO{sub 2} and minerals relevant to underground storage of CO{sub 2} (geologic carbon sequestration). The apparatus could also be utilized to study high-pressure interfacial chemistry in other areas such as catalysis, polymerization, food processing, and oil and gas recovery.

  3. SmNd disequilibrium in high-pressure, low-temperature Himalayan and Alpine rocks

    E-Print Network [OSTI]

    Nicolas, Chamot-Rooke

    disequilibrium in high-pressure, low-temperature rocks, Sm­Nd isotopic analyses were carried out on minerals from contamination processes. In the case of a magmatic protolith, contamination can be achieved through crustal sedimentary protolith contains components from an old contaminant crust. In the Himalayan samples, the inverse

  4. High pressure studies on uranium and thorium silicide compounds: Experiment S. Yagoubi a,b,c,

    E-Print Network [OSTI]

    Svane, Axel Torstein

    High pressure studies on uranium and thorium silicide compounds: Experiment and theory S. Yagoubi a, USi3, as well as some non-stoichiometric phases presented in Table 1. Among the thoriumB-type) that a ferromagnetic ordering is reported, with TC = 127 K and a saturated moment of 0.1 lB [3]. Concerning the thorium

  5. Stability of very-high pressure arc discharges against perturbations of the electron temperature

    SciTech Connect (OSTI)

    Benilov, M. S. [Departamento de Fisica, Ciencias Exactas e Engenharia, Universidade da Madeira, Largo do Municipio, Funchal 9000 (Portugal); Hechtfischer, U. [Philips Lighting, BU Automotive Lamps, Technology, Philipsstrasse 8, Aachen 52068 (Germany)

    2012-04-01T23:59:59.000Z

    We study the stability of the energy balance of the electron gas in very high-pressure plasmas against longitudinal perturbations, using a local dispersion analysis. After deriving a dispersion equation, we apply the model to a very high-pressure (100 bar) xenon plasma and find instability for electron temperatures, T{sub e}, in a window between 2400 K and 5500-7000 K x 10{sup 3} K, depending on the current density (10{sup 6}-10{sup 8} A/m{sup 2}). The instability can be traced back to the Joule heating of the electron gas being a growing function of T{sub e}, which is due to a rising dependence of the electron-atom collision frequency on T{sub e}. We then analyze the T{sub e} range occurring in very high-pressure xenon lamps and conclude that only the near-anode region exhibits T{sub e} sufficiently low for this instability to occur. Indeed, previous experiments have revealed that such lamps develop, under certain conditions, voltage oscillations accompanied by electromagnetic interference, and this instability has been pinned down to the plasma-anode interaction. A relation between the mechanisms of the considered instability and multiple anodic attachments of high-pressure arcs is discussed.

  6. Aragonite pseudomorphs in high-pressure marbles of Syros, Greece John B. Bradya,*, Michelle J. Markleyb

    E-Print Network [OSTI]

    Brady, John B.

    Aragonite pseudomorphs in high-pressure marbles of Syros, Greece John B. Bradya,*, Michelle J in the blueschist to eclogite facies marbles of Syros, Greece. The rods show a shape-preferred orientation is unusually low (Carlson and Rosenfeld, 1981). Although marbles on the island of Syros (Cyclades, Greece

  7. Journal of Applied Physics 104,093504 (2008) Picosecond laser structuration under high pressures

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    2008-01-01T23:59:59.000Z

    A research on ultra-short laser modification of materials has been a subject of numerous studies last two. The main effect is specific to the ambient gas and laser pulse duration in the ablation regime: whenJournal of Applied Physics 104,093504 (2008) Picosecond laser structuration under high pressures

  8. High-pressure phases of CaCO3: Crystal structure prediction and experiment

    E-Print Network [OSTI]

    Oganov, Artem R.

    High-pressure phases of CaCO3: Crystal structure prediction and experiment Artem R. Oganov a October 2005 Available online 18 November 2005 Editor: G.D. Price Abstract Post-aragonite phase of CaCO3 transformation in CaCO3 at 40 GPa, Am. Mineral. 90 (2005) 667­671], is believed to be a major carbon- containing

  9. High-pressure phases of FeTiO3 from first principles N. C. Wilson

    E-Print Network [OSTI]

    2005; published 19 July 2005 The structural, elastic, and electronic properties of the high-pressure Fe and their interaction with the structural degrees of freedom. Ilmenite, the mineral form of FeTiO3, is commonly found of diamond deposits.2 In addition to ilmenite, two other polymorphs of FeTiO3 are known,3 namely, the lithium

  10. Ultrafast high-pressure AC electro-osmotic pumps for portable biomedical microfluidics

    E-Print Network [OSTI]

    Bazant, Martin Z.

    Ultrafast high-pressure AC electro-osmotic pumps for portable biomedical microfluidics Chien details the development of an integrated AC electro-osmotic (ACEO) microfluidic pump for dilute (100 mM) biological solutions in separate microfluidic devices, with potential applications in portable

  11. Studies of Charge Exchange in a High?Pressure Pulsed Electron Impact Source

    E-Print Network [OSTI]

    Sharma, D. K. Sen; Hierl, Peter M.; Franklin, J. L.

    1972-01-01T23:59:59.000Z

    A high pressure pulsed ion source has been used in a time?of?flight mass spectrometer in order to study the charge exchangereactions in Ar–H2 and Ar–D2 systems using the ion source in the ?ermák mode of operation. As the source was used in a pulsed...

  12. Acceptance test report for high pressure water jet system feed pump

    SciTech Connect (OSTI)

    Crystal, J.B.

    1996-03-12T23:59:59.000Z

    This document summarizes results of WHC-SD-SNF-ATP-016, Rev. 0 ``Acceptance Test Procedure High Pressure Water Jet System``, conducted on December 20, 1995 and December 22, 1995. This jet supplies water at 15,000 psi @ 15 gpm to nozzles to clean surfaces of empty fuel storage canisters.

  13. Design, modeling, fabrication and testing of a piezoelectric microvalve for high pressure, high frequency hydraulic applications

    E-Print Network [OSTI]

    Roberts, David C. (David Christopher)

    2002-01-01T23:59:59.000Z

    A piezoelectrically-driven hydraulic amplification microvalve for use in high specific power hydraulic pumping applications was designed, fabricated, and experimentally characterized. High frequency, high force actuation ...

  14. A compact high-performance low-field NMR apparatus for measurements on fluids at very high pressures and temperatures

    SciTech Connect (OSTI)

    Freedman, R.; Anand, V., E-mail: VAnand@slb.com; Ganesan, K.; Tabrizi, P.; Torres, R. [Schlumberger Technology Corp., 110 Schlumberger Drive, Sugar Land, Texas 77478 (United States)] [Schlumberger Technology Corp., 110 Schlumberger Drive, Sugar Land, Texas 77478 (United States); Grant, B. [Grant Innovation, 618 Mesquite Drive, Cedar Creek, Texas 78612 (United States)] [Grant Innovation, 618 Mesquite Drive, Cedar Creek, Texas 78612 (United States); Catina, D. [National Oilwell Varco, 10302 Mula Road, Stafford, Texas 77477 (United States)] [National Oilwell Varco, 10302 Mula Road, Stafford, Texas 77477 (United States); Ryan, D.; Borman, C.; Krueckl, C. [Schlumberger DBR Technology Center, 9450–17 Avenue NW, Edmonton, Alberta (Canada)] [Schlumberger DBR Technology Center, 9450–17 Avenue NW, Edmonton, Alberta (Canada)

    2014-02-15T23:59:59.000Z

    We discuss an innovative new high-performance apparatus for performing low-field Nuclear Magnetic Resonance (NMR) relaxation times and diffusion measurements on fluids at very high pressures and high temperatures. The apparatus sensor design and electronics specifications allow for dual deployment either in a fluid sampling well logging tool or in a laboratory. The sensor and electronics were designed to function in both environments. This paper discusses the use of the apparatus in a laboratory environment. The operating temperature and pressure limits, and the signal-to-noise ratio (SNR) of the new system exceed by a very wide margin what is currently possible. This major breakthrough was made possible by a revolutionary new sensor design that breaks many of the rules of conventional high pressure NMR sensor design. A metallic sample holder capable of operating at high pressures and temperatures is provided to contain the fluid under study. The sample holder has been successfully tested for operation up to 36 Kpsi. A solenoid coil wound on a slotted titanium frame sits inside the metallic sample holder and serves as an antenna to transmit RF pulses and receive NMR signals. The metal sample holder is sandwiched between a pair of gradient coils which provide a linear field gradient for pulsed field gradient diffusion measurements. The assembly sits in the bore of a low-gradient permanent magnet. The system can operate over a wide frequency range without the need for tuning the antenna to the Larmor frequency. The SNR measured on a water sample at room temperature is more than 15 times greater than that of the commercial low-field system in our laboratory. Thus, the new system provides for data acquisition more than 200 times faster than was previously possible. Laboratory NMR measurements of relaxations times and diffusion coefficients performed at pressures up to 25 Kpsi and at temperatures up to 175?°C with crude oils enlivened with dissolved hydrocarbon gases (referred to as “live oils”) are shown. This is the first time low-field NMR measurements have been performed at such high temperatures and pressures on live crude oil samples. We discuss the details of the apparatus design, tuning, calibration, and operation. NMR data acquired at multiple temperatures and pressures on a live oil sample are discussed.

  15. Innovative high pressure gas MEM's based neutron detector for ICF and active SNM detection.

    SciTech Connect (OSTI)

    Martin, Shawn Bryan; Derzon, Mark Steven; Renzi, Ronald F.; Chandler, Gordon Andrew

    2007-12-01T23:59:59.000Z

    An innovative helium3 high pressure gas detection system, made possible by utilizing Sandia's expertise in Micro-electrical Mechanical fluidic systems, is proposed which appears to have many beneficial performance characteristics with regards to making these neutron measurements in the high bremsstrahlung and electrical noise environments found in High Energy Density Physics experiments and especially on the very high noise environment generated on the fast pulsed power experiments performed here at Sandia. This same system may dramatically improve active WMD and contraband detection as well when employed with ultrafast (10-50 ns) pulsed neutron sources.

  16. Phase transition and metallization of FeO at high pressures and temperatures

    SciTech Connect (OSTI)

    Fischer, Rebecca A.; Campbell, Andrew J.; Lord, Oliver T.; Shofner, Gregory A.; Dera, Przemyslaw; Prakapenka, Vitali B. (Maryland); (UC); (UCL)

    2012-05-10T23:59:59.000Z

    Wuestite, Fe{sub 1-x}O, is an important component in the mineralogy of Earth's lower mantle and may also be a component of the core. Therefore its high pressure-temperature behavior, including its electronic structure, is essential to understanding the nature and evolution of Earth's deep interior. We performed X-ray diffraction and radiometric measurements on wuestite in a laser-heated diamond anvil cell, finding an insulator-metal transition at high pressures and temperatures. Our data show a negative slope for this apparently isostructural phase boundary, which is characterized by a volume decrease and emissivity increase. The metallic phase of FeO is stable at conditions of the lower mantle and core, which has implications for the high P-T character of Fe-O bonds, magnetic field propagation, and lower mantle conductivity.

  17. High-pressure structural and elastic properties of Tl{sub 2}O{sub 3}

    SciTech Connect (OSTI)

    Gomis, O., E-mail: osgohi@fis.upv.es; Vilaplana, R. [Centro de Tecnologías Físicas, MALTA Consolider Team, Universitat Politècnica de València, 46022 València (Spain); Santamaría-Pérez, D. [Departamento de Física Aplicada-ICMUV, MALTA Consolider Team, Universidad de Valencia, Edificio de Investigación, C/Dr. Moliner 50, 46100 Burjassot (Spain); Earth Sciences Department, University College London, Gower Street, WC1E 6BT London (United Kingdom); Ruiz-Fuertes, J. [Departamento de Física Aplicada-ICMUV, MALTA Consolider Team, Universidad de Valencia, Edificio de Investigación, C/Dr. Moliner 50, 46100 Burjassot (Spain); Geowissenschaften, Goethe-Universität, Altenhöferallee 1, 60438 Frankfurt am Main (Germany); Sans, J. A.; Manjón, F. J.; Mollar, M. [Instituto de Diseño para la Fabricación y Producción Automatizada, MALTA Consolider Team, Universitat Politècnica de València, 46022 València (Spain); and others

    2014-10-07T23:59:59.000Z

    The structural properties of Thallium (III) oxide (Tl{sub 2}O{sub 3}) have been studied both experimentally and theoretically under compression at room temperature. X-ray powder diffraction measurements up to 37.7?GPa have been complemented with ab initio total-energy calculations. The equation of state of Tl{sub 2}O{sub 3} has been determined and compared to related compounds. It has been found experimentally that Tl{sub 2}O{sub 3} remains in its initial cubic bixbyite-type structure up to 22.0?GPa. At this pressure, the onset of amorphization is observed, being the sample fully amorphous at 25.2?GPa. The sample retains the amorphous state after pressure release. To understand the pressure-induced amorphization process, we have studied theoretically the possible high-pressure phases of Tl{sub 2}O{sub 3}. Although a phase transition is theoretically predicted at 5.8?GPa to the orthorhombic Rh{sub 2}O{sub 3}-II-type structure and at 24.2?GPa to the orthorhombic ?-Gd{sub 2}S{sub 3}-type structure, neither of these phases were observed experimentally, probably due to the hindrance of the pressure-driven phase transitions at room temperature. The theoretical study of the elastic behavior of the cubic bixbyite-type structure at high-pressure shows that amorphization above 22?GPa at room temperature might be caused by the mechanical instability of the cubic bixbyite-type structure which is theoretically predicted above 23.5?GPa.

  18. High-beta plasma effects in a low-pressure helicon plasma

    SciTech Connect (OSTI)

    Corr, C. S.; Boswell, R. W. [Space Plasma, Power and Propulsion Group (SP3), Research School of Physical Science and Engineering, Australian National University, Canberra ACT 0200 (Australia)

    2007-12-15T23:59:59.000Z

    In this work, high-beta plasma effects are investigated in a low-pressure helicon plasma source attached to a large volume diffusion chamber. When operating above an input power of 900 W and a magnetic field of 30 G a narrow column of bright blue light (due to Ar II radiation) is observed along the axis of the diffusion chamber. With this blue mode, the plasma density is axially very uniform in the diffusion chamber; however, the radial profiles are not, suggesting that a large diamagnetic current might be induced. The diamagnetic behavior of the plasma has been investigated by measuring the temporal evolution of the magnetic field (B{sub z}) and the plasma kinetic pressure when operating in a pulsed discharge mode. It is found that although the electron pressure can exceed the magnetic field pressure by a factor of 2, a complete expulsion of the magnetic field from the plasma interior is not observed. In fact, under our operating conditions with magnetized ions, the maximum diamagnetism observed is {approx}2%. It is observed that the magnetic field displays the strongest change at the plasma centre, which corresponds to the maximum in the plasma kinetic pressure. These results suggest that the magnetic field diffuses into the plasma sufficiently quickly that on a long time scale only a slight perturbation of the magnetic field is ever observed.

  19. High Temperature, high pressure equation of state density correlations and viscosity correlations

    SciTech Connect (OSTI)

    Tapriyal, D.; Enick, R.; McHugh, M.; Gamwo, I.; Morreale, B.

    2012-07-31T23:59:59.000Z

    Global increase in oil demand and depleting reserves has derived a need to find new oil resources. To find these untapped reservoirs, oil companies are exploring various remote and harsh locations such as deep waters in Gulf of Mexico, remote arctic regions, unexplored deep deserts, etc. Further, the depth of new oil/gas wells being drilled has increased considerably to tap these new resources. With the increase in the well depth, the bottomhole temperature and pressure are also increasing to extreme values (i.e. up to 500 F and 35,000 psi). The density and viscosity of natural gas and crude oil at reservoir conditions are critical fundamental properties required for accurate assessment of the amount of recoverable petroleum within a reservoir and the modeling of the flow of these fluids within the porous media. These properties are also used to design appropriate drilling and production equipment such as blow out preventers, risers, etc. With the present state of art, there is no accurate database for these fluid properties at extreme conditions. As we have begun to expand this experimental database it has become apparent that there are neither equations of state for density or transport models for viscosity that can be used to predict these fundamental properties of multi-component hydrocarbon mixtures over a wide range of temperature and pressure. Presently, oil companies are using correlations based on lower temperature and pressure databases that exhibit an unsatisfactory predictive capability at extreme conditions (e.g. as great as {+-} 50%). From the perspective of these oil companies that are committed to safely producing these resources, accurately predicting flow rates, and assuring the integrity of the flow, the absence of an extensive experimental database at extreme conditions and models capable of predicting these properties over an extremely wide range of temperature and pressure (including extreme conditions) makes their task even more daunting.

  20. Vapor Pressures and Heats of Vaporization of Primary Coal Tars

    Office of Scientific and Technical Information (OSTI)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItem Not FoundInformation DOEInformation Summary Big*Theea Dynamic Performance-

  1. Integrated natural-gas-engine cooling jacket vapor-compressor program. Annual progress report (phase 2), January-December 1987

    SciTech Connect (OSTI)

    DiBella, F.A.; Becker, F.

    1988-01-01T23:59:59.000Z

    A unique, alternative cogeneration system was designed that will provide an industrial or commercial energy user with high-pressure steam and electricity directly from a packaged cogeneration system. The Integrated Gas Engine Vapor Compression System concept includes an engine-generator set and a steam screw compressor that are mechanically integrated with the engine. The gas-fueled engine is ebulliently cooled, thus allowing its water jacket heat to be recovered in the form of low-pressure steam. This steam is then compressed by the steam compressor to a higher pressure, and when combined with the high-pressure steam generated in the engine's exhaust gas boiler it provides the end user with a more useable thermal energy source. Phase 1B of this project was completed in 1986 and consisted primarily of the procurement of equipment and the final design and assembly of a prototype integrated gas-engine vapor-compression system.

  2. Studies of local and intermediate range structure in crystalline and amorphouse materials at high pressure using high-energy x-rays.

    SciTech Connect (OSTI)

    Ehm, L.; Antao, M.; Chen, J.; Locke, D. R.; Michel, F. M.; Martin, C. D.; Yu, T.; Lee, P. L.; Chupas, P. J.; Shastri, S. D.; Guo, Q.; Parise, J. B.; Stony Brook Univ.; BNL

    2007-06-01T23:59:59.000Z

    The method of high-energy total elastic X-ray scattering to determine the atomic structure of nanocrystalline, highly disordered, and amorphous materials is presented. The current state of the technique, its potential, and limitations are discussed with two successful studies on the pressure induced phase transition in mackinawite (FeS) and the high-pressure behavior of liquid gallium.

  3. Studies of Local and Intermediate Range Structure in Crystalline and Amorphous Materials at High Pressure Using High-Energy X-rays

    SciTech Connect (OSTI)

    Ehm,L.; Antao, S.; Chen, J.; Locke, D.; Michel, F.; Martin, D.; Yu, T.; Parise, J.; Lee, P.; et al.

    2007-01-01T23:59:59.000Z

    The method of high-energy total elastic X-ray scattering to determine the atomic structure of nanocrystalline, highly disordered, and amorphous materials is presented. The current state of the technique, its potential, and limitations are discussed with two successful studies on the pressure induced phase transition in mackinawite (FeS) and the high-pressure behavior of liquid gallium.

  4. Effect of NH{sub 3} on the low pressure chemical vapor deposition of TiO{sub 2} film at low temperature using tetrakis(diethylamino)titanium and oxygen

    SciTech Connect (OSTI)

    Song Xuemei; Takoudis, Christos G. [Department of Chemical Engineering, University of Illinois at Chicago, Chicago, Illinois 60607 (United States); Department of Chemical Engineering, University of Illinois at Chicago, Chicago, Illinois 60607 and Department of Bioengineering, University of Illinois at Chicago, Chicago, Illinois 60607 (United States)

    2007-03-15T23:59:59.000Z

    The effect of NH{sub 3} on TiO{sub 2} film deposition using tetrakis(diethylamino)titanium (TDEAT) and O{sub 2} as source gases in a low pressure chemical vapor deposition reactor was studied at low temperatures ranging from 100 to 250 deg. C. TiO{sub 2} film is traditionally deposited at temperature above 300 deg. C using oxygen-based Ti precursors, such as titanium tetraisopropoxide. In this study, the authors demonstrate that a combination of both reactive precursors, i.e., TDEAT and NH{sub 3}, is an effective technique for TiO{sub 2} film deposition at lower temperatures, albeit with some nitrogen incorporation. It was found that films can be formed at temperatures as low as 100 deg. C when NH{sub 3} is used. At higher temperatures, the growth rate of TiO{sub 2} films deposited using NH{sub 3} is higher than that of films deposited without NH{sub 3} by up to one order of magnitude. X-ray photoelectron spectroscopy data show that NH{sub 3} enhances the formation of TiNO and TiN, and x-ray diffraction analysis shows that all as-deposited films have amorphous structure. Both x-ray photoelectron spectroscopy and secondary ion mass spectroscopy depth profiles show that nitrogen, carbon, and oxygen are uniformly distributed throughout the film. The mechanism of enhancement of growth rate using NH{sub 3} is also discussed.

  5. Materials, methods and devices to detect and quantify water vapor concentrations in an atmosphere

    DOE Patents [OSTI]

    Allendorf, Mark D; Robinson, Alex L

    2014-12-09T23:59:59.000Z

    We have demonstrated that a surface acoustic wave (SAW) sensor coated with a nanoporous framework material (NFM) film can perform ultrasensitive water vapor detection at concentrations in air from 0.05 to 12,000 ppmv at 1 atmosphere pressure. The method is extendable to other MEMS-based sensors, such as microcantilevers, or to quartz crystal microbalance sensors. We identify a specific NFM that provides high sensitivity and selectivity to water vapor. However, our approach is generalizable to detection of other species using NFM to provide sensitivity and selectivity.

  6. Direct vapor/solid synthesis of mercuric iodide using compounds of mercury and iodine

    SciTech Connect (OSTI)

    Skinner, Nathan L. (Carpinteria, CA)

    1990-01-01T23:59:59.000Z

    A process is disclosed for producing high purity mercuric iodide by passing a gaseous source of a mercuric compound through a particulate bed of a low vapor pressure iodide compound which is maintained at an elevated temperature which is the lower of either: (a) just below the melting or volatilization temperature of the iodide compound (which ever is lower); or (b) just below the volatilization point of the other reaction product formed during the reaction; to cause the mercuric compound to react with the iodide compound to form mercuric iodide which then passes as a vapor out of the bed into a cooler condensation region.

  7. Direct containment heating and aerosol generation during high-pressure-melt expulsion experiments

    SciTech Connect (OSTI)

    Tarbell, W.W.; Brockmann, J.E.; Washington, K.E.; Pilch, M.; Marx, K.D.

    1988-01-01T23:59:59.000Z

    Severe nuclear plant accidents can involve the degradation of the reactor core while the primary coolant system remains pressurized. Molten fuel reaching the lower head of the reactor pressure vessel (RPV) may attack and fail the instrument guide tube penetrations, allowing the tube to be expelled from the vessel. The resulting aperture allows the molten fuel to be ejected into the cavity, followed by the blowdown of the contents of the primary system (high-pressure-melt ejection). Entrainment of the core debris in the cavity by the blowdown gases may cause high-temperature fuel particles to be carried into the containment building. Energy exchange between the particles and the atmosphere may cause heating and pressurizing of the containment (direct containment heating (DCH)). The complex phenomena associated with direct containment heating accident sequences are not well understood. This work describes a series of four experiments that have been performed to study and quantify the processes involved. The data from the experiments are used to guide the development of computer models to describe the response of containments under accident conditions.

  8. Dark Matter Directionality Revisited with a High Pressure Xenon Gas Detector

    E-Print Network [OSTI]

    Gopolang Mohlabeng; Kyoungchul Kong; Jin Li; Adam Para; Jonghee Yoo

    2015-03-13T23:59:59.000Z

    An observation of the anisotropy of dark matter interactions in a direction-sensitive detector would provide decisive evidence for the discovery of galactic dark matter. Directional information would also provide a crucial input to understanding its distribution in the local Universe. Most of the existing directional dark matter detectors utilize particle tracking methods in a low-pressure gas time projection chamber. These low pressure detectors require excessively large volumes in order to be competitive in the search for physics beyond the current limit. In order to avoid these volume limitations, we consider a novel proposal, which exploits a columnar recombination effect in a high-pressure gas time projection chamber. The ratio of scintillation to ionization signals observed in the detector carries the angular information of the particle interactions. In this paper, we investigate the sensitivity of a future directional detector focused on the proposed high-pressure Xenon gas time projection chamber. We study the prospect of detecting an anisotropy in the dark matter velocity distribution. We find that tens of events are needed to exclude an isotropic distribution of dark matter interactions at 95% confidence level in the most optimistic case with head-to-tail information. However, one needs at least 10-20 times more events without head-to-tail information for light dark matter below 50 GeV or one between 200 GeV and 400 GeV. For an intermediate mass range, we find it challenging to observe anisotropy of dark matter distribution.

  9. Study of liquid gallium at high pressure using synchrotron x-ray

    SciTech Connect (OSTI)

    Yu, Tony; Guo Quanzhong; Parise, John [Department of Geosciences, Mineral Physics Institute, Stony Brook University, Stony Brook, New York 11794-2100 (United States); Chen Jiuhua [Department of Geosciences, Mineral Physics Institute, Stony Brook University, Stony Brook, New York 11794-2100 (United States); Department of Mechanical and Materials Engineering, Center for the Study of Matters at Extreme Conditions, Florida International University, Miami, Florida 33199 (United States); Ehm, Lars [Department of Geosciences, Mineral Physics Institute, Stony Brook University, Stony Brook, New York 11794-2100 (United States); National Synchrotron Light Source, Brookhaven National Laboratory, Upton, New York 11973-5000 (United States); Huang Shu [Department of Mechanical and Materials Engineering, Center for the Study of Matters at Extreme Conditions, Florida International University, Miami, Florida 33199 (United States); Luo Shengnian [Physics Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States)

    2012-06-01T23:59:59.000Z

    Liquid gallium has been studied at high pressure up to 2 GPa and ambient temperature in a diamond anvil cell using high energy synchrotron x-ray beam. The total x-ray scattering data of liquid gallium were collected up to Q = 12 A{sup -1} and analyzed using pair distribution functions (PDF). The results indicate that the first nearest neighbor peak and second nearest neighbor (shoulder) peak of PDF in liquid gallium does not change with pressure, whereas the higher order (i.e., third and fourth) nearest neighbor peaks shift towards shorter distance with increasing pressure. Reverse Monte Carlo modeling based on the observed data shows that the coordination number in the liquid gallium increases with pressure from 10.5 at 0.3 GPa to 11.6 at 2 GPa. An atomic arrangement similar to the crystalline phase of Ga(II) with coordination number of 12 is proposed for the locally dense-packed rigid unit in liquid gallium. The volume compression data derived from the structure modeling yield a bulk modulus of 12.1(6) GPa for liquid gallium.

  10. Comparison of high pressure transient PVT measurements and model predictions. Part I.

    SciTech Connect (OSTI)

    Felver, Todd G.; Paradiso, Nicholas Joseph; Evans, Gregory Herbert; Rice, Steven F.; Winters, William Stanley, Jr.

    2010-07-01T23:59:59.000Z

    A series of experiments consisting of vessel-to-vessel transfers of pressurized gas using Transient PVT methodology have been conducted to provide a data set for optimizing heat transfer correlations in high pressure flow systems. In rapid expansions such as these, the heat transfer conditions are neither adiabatic nor isothermal. Compressible flow tools exist, such as NETFLOW that can accurately calculate the pressure and other dynamical mechanical properties of such a system as a function of time. However to properly evaluate the mass that has transferred as a function of time these computational tools rely on heat transfer correlations that must be confirmed experimentally. In this work new data sets using helium gas are used to evaluate the accuracy of these correlations for receiver vessel sizes ranging from 0.090 L to 13 L and initial supply pressures ranging from 2 MPa to 40 MPa. The comparisons show that the correlations developed in the 1980s from sparse data sets perform well for the supply vessels but are not accurate for the receivers, particularly at early time during the transfers. This report focuses on the experiments used to obtain high quality data sets that can be used to validate computational models. Part II of this report discusses how these data were used to gain insight into the physics of gas transfer and to improve vessel heat transfer correlations. Network flow modeling and CFD modeling is also discussed.

  11. High pressure pair distribution function studies of Green River oil shale.

    SciTech Connect (OSTI)

    Chapman, K. W.; Chupas, P. J.; Locke, D. R.; Winans, R. E.; Pugmire, R. J.; Univ. of Utah

    2008-01-01T23:59:59.000Z

    The compression behavior of a silicate-rich oil shale from the Green River formation in the pressure range 0.0-2.4 GPa was studied using in situ high pressure X-ray pair distribution function (PDF) measurements for the sample contained within a Paris-Edinburgh cell. The real-space local structural information in the PDF, G(r), was used to evaluate the compressibility of the oil shale. Specifically, the pressure-induced reduction in the medium- to long-range atom distances ({approx}6-20 {angstrom}) yielded an average sample compressibility corresponding to a bulk modulus of ca. 61-67 GPa. A structural model consisting of a three phase mixture of the principal crystalline oil shale components (quartz, albite and Illite) provided a good fit to the ambient pressure PDF data (R {approx} 30.7%). Indeed the features in the PDF beyond {approx} {angstrom}, were similarly well fit by a single phase model of the highest symmetry, highly crystalline quartz component. The factors influencing the observed compression behavior are discussed.

  12. Measurement and interpretation of threshold stress intensity factors for steels in high-pressure hydrogen gas.

    SciTech Connect (OSTI)

    Dadfarnia, Mohsen (University of Illinois at Urbana-Champaign, Urbana, IL); Nibur, Kevin A.; San Marchi, Christopher W.; Sofronis, Petros (University of Illinois at Urbana-Champaign, Urbana, IL); Somerday, Brian P.; Foulk, James W., III; Hayden, Gary A. (CP Industries, McKeesport, PA)

    2010-07-01T23:59:59.000Z

    Threshold stress intensity factors were measured in high-pressure hydrogen gas for a variety of low alloy ferritic steels using both constant crack opening displacement and rising crack opening displacement procedures. The sustained load cracking procedures are generally consistent with those in ASME Article KD-10 of Section VIII Division 3 of the Boiler and Pressure Vessel Code, which was recently published to guide design of high-pressure hydrogen vessels. Three definitions of threshold were established for the two test methods: K{sub THi}* is the maximum applied stress intensity factor for which no crack extension was observed under constant displacement; K{sub THa} is the stress intensity factor at the arrest position for a crack that extended under constant displacement; and K{sub JH} is the stress intensity factor at the onset of crack extension under rising displacement. The apparent crack initiation threshold under constant displacement, K{sub THi}*, and the crack arrest threshold, K{sub THa}, were both found to be non-conservative due to the hydrogen exposure and crack-tip deformation histories associated with typical procedures for sustained-load cracking tests under constant displacement. In contrast, K{sub JH}, which is measured under concurrent rising displacement and hydrogen gas exposure, provides a more conservative hydrogen-assisted fracture threshold that is relevant to structural components in which sub-critical crack extension is driven by internal hydrogen gas pressure.

  13. High mobility single-crystalline-like GaAs thin films on inexpensive flexible metal substrates by metal-organic chemical vapor deposition

    SciTech Connect (OSTI)

    Dutta, P., E-mail: pdutta2@central.uh.edu; Rathi, M.; Gao, Y.; Yao, Y.; Selvamanickam, V. [Department of Mechanical Engineering, University of Houston, Houston, Texas 77204 (United States); Zheng, N.; Ahrenkiel, P. [Department of Nanoscience and Nanoengineering, South Dakota School of Mines and Technology, Rapid City, South Dakota 57701 (United States); Martinez, J. [Materials Evaluation Laboratory, NASA Johnson Space Center, Houston, Texas 77085 (United States)

    2014-09-01T23:59:59.000Z

    We demonstrate heteroepitaxial growth of single-crystalline-like n and p-type doped GaAs thin films on inexpensive, flexible, and light-weight metal foils by metal-organic chemical vapor deposition. Single-crystalline-like Ge thin film on biaxially textured templates made by ion beam assisted deposition on metal foil served as the epitaxy enabling substrate for GaAs growth. The GaAs films exhibited strong (004) preferred orientation, sharp in-plane texture, low grain misorientation, strong photoluminescence, and a defect density of ?10{sup 7?}cm{sup ?2}. Furthermore, the GaAs films exhibited hole and electron mobilities as high as 66 and 300?cm{sup 2}/V-s, respectively. High mobility single-crystalline-like GaAs thin films on inexpensive metal substrates can pave the path for roll-to-roll manufacturing of flexible III-V solar cells for the mainstream photovoltaics market.

  14. Breakdown of Angular Momentum Selection Rules in High Pressure Optical Pumping Experiments

    SciTech Connect (OSTI)

    Lancor, B.; Wyllie, R.; Walker, T. G. [Department of Physics, University of Wisconsin-Madison, Madison, Wisconsin 53706 (United States); Babcock, E. [Juelich Centre for Neutron Science, Garching 85747 (Germany)

    2010-08-20T23:59:59.000Z

    We present measurements, by using two complementary methods, of the breakdown of atomic angular momentum selection rules in He-broadened Rb vapor. Atomic dark states are rendered weakly absorbing due to fine-structure mixing during Rb-He collisions. The effect substantially increases the photon demand for optical pumping of dense vapors.

  15. Rigorous Simulation of Accidental Leaks from High-Pressure Storage Vessels

    E-Print Network [OSTI]

    Alisha, -

    2014-07-07T23:59:59.000Z

    of nature. The released chemical can form and disperse as vapor cloud leading to fire, explosion, or toxic exposure. The resulting leak could be single phase or multiphase release, choked or non-choked. These releases could result in liquid spills, vapor...

  16. Rigorous Simulation of Accidental Leaks from High-Pressure Storage Vessels 

    E-Print Network [OSTI]

    Alisha, -

    2014-07-07T23:59:59.000Z

    of nature. The released chemical can form and disperse as vapor cloud leading to fire, explosion, or toxic exposure. The resulting leak could be single phase or multiphase release, choked or non-choked. These releases could result in liquid spills, vapor...

  17. Staged, High-Pressure Oxy-Combustion Technology: Development and Scale-Up

    SciTech Connect (OSTI)

    Axelbaum, Richard; Xia, Fei; Gopan, Akshay; Kumfer, Benjamin

    2014-09-30T23:59:59.000Z

    Washington University in St. Louis and its project partners are developing a unique pressurized oxy-combustion process that aims to improve efficiency and costs by reducing the recycling of flue gas to near zero. Normally, in the absence of recycled flue gas or another inert gas, combustion of fuel and oxygen results in a dramatic increase in temperature of the combustion products and radiant energy, as compared to combustion in air. High heat flux to the boiler tubes may result in a tube surface temperatures that exceed safe operating limits. In the Staged Pressurized Oxy-Combustion (SPOC) process, this problem is addressed by staging the delivery of fuel and by novel combustion design that allows control of heat flux. In addition, the main mode of heat transfer to the steam cycle is by radiation, as opposed to convection. Therefore, the requirement for recycling large amounts of flue gas, for temperature control or to improve convective heat transfer, is eliminated, resulting in a reduction in auxiliary loads. The following report contains a detailed summary of scientific findings and accomplishments for the period of Oct. 1, 2013 to Sept 30, 2014. Results of ASPEN process and CFD modelling activities aimed at improving the SPOC process and boiler design are presented. The effects of combustion pressure and fuel moisture on the plant efficiency are discussed. Combustor pressure is found to have only a minor impact beyond 16 bar. For fuels with moisture content greater than approx 30%, e.g. coal/water slurries, the amount of latent heat of condensation exceeds that which can be utilized in the steam cycle and plant efficiency is reduced significantly. An improved boiler design is presented that achieves a more uniform heat flux profile. In addition, a fundamental study of radiation in high-temperature, high-pressure, particle-laden flows is summarized which provides a more complete understanding of heat transfer in these unusual conditions and to allow for optimization. The results reveal that for the SPOC design, absorption and emission due to particles is the dominant factor for determining the wall heat flux. The mechanism of “radiative trapping” of energy within the high-temperature flame region and the approach to utilizing this mechanism to control wall heat flux are described. This control arises, by design, from the highly non-uniform (non-premixed) combustion characteristics within the SPOC boiler, and the resulting gradients in temperature and particle concentration. Finally, a simple method for estimating the wall heat flux in pressurized combustion systems is presented.

  18. Enrichment of HFSE in chlorite-harzburgite produced by high-pressure dehydration of antigorite-serpentinite

    E-Print Network [OSTI]

    Demouchy, Sylvie

    Enrichment of HFSE in chlorite-harzburgite produced by high-pressure dehydration of antigorite of antigorite-serpentinite produces chlorite- harzburgite relatively enriched in HFSE due to the stabilization. Godard (2005), Enrichment of HFSE in chlorite-harzburgite produced by high-pressure dehydration

  19. DEVELOPMENT OF A LOW PRESSURE, AIR ATOMIZED OIL BURNER WITH HIGH ATOMIZER AIR FLOW

    SciTech Connect (OSTI)

    BUTCHER,T.A.

    1998-01-01T23:59:59.000Z

    This report describes technical advances made to the concept of a low pressure, air atomized oil burner for home heating applications. Currently all oil burners on the market are of the pressure atomized, retention head type. These burners have a lower firing rate limit of about 0.5 gallons per hour of oil, due to reliability problems related to small flow passage sizes. High pressure air atomized burners have been shown to be one route to avoid this problem but air compressor cost and reliability have practically eliminated this approach. With the low pressure air atomized burner the air required for atomization can be provided by a fan at 5--8 inches of water pressure. A burner using this concept, termed the Fan-Atomized Burner or FAB has been developed and is currently being commercialized. In the head of the FAB, the combustion air is divided into three parts, much like a conventional retention head burner. This report describes development work on a new concept in which 100% of the air from the fan goes through the atomizer. The primary advantage of this approach is a great simplification of the head design. A nozzle specifically sized for this concept was built and is described in the report. Basic flow pressure tests, cold air velocity profiles, and atomization performance have been measured. A burner head/flame tube has been developed which promotes a torroidal recirculation zone near the nozzle for flame stability. The burner head has been tested in several furnace and boiler applications over the tiring rate range 0.2 to 0.28 gallons per hour. In all cases the burner can operate with very low excess air levels (under 10%) without producing smoke. Flue gas NO{sub x} concentration varied from 42 to 62 ppm at 3% 0{sub 2}. The concept is seen as having significant potential and planned development efforts are discussed.

  20. Apparatus and method for enhanced chemical processing in high pressure and atmospheric plasmas produced by high frequency electromagnetic waves

    DOE Patents [OSTI]

    Efthimion, Philip C. (Bedminister, NJ); Helfritch, Dennis J. (Flemington, NJ)

    1989-11-28T23:59:59.000Z

    An apparatus and method for creating high temperature plasmas for enhanced chemical processing of gaseous fluids, toxic chemicals, and the like, at a wide range of pressures, especially at atmospheric and high pressures includes an electro-magnetic resonator cavity, preferably a reentrant cavity, and a wave guiding structure which connects an electro-magnetic source to the cavity. The cavity includes an intake port and an exhaust port, each having apertures in the conductive walls of the cavity sufficient for the intake of the gaseous fluids and for the discharge of the processed gaseous fluids. The apertures are sufficiently small to prevent the leakage of the electro-magnetic radiation from the cavity. Gaseous fluid flowing from the direction of the electro-magnetic source through the guiding wave structure and into the cavity acts on the plasma to push it away from the guiding wave structure and the electro-magnetic source. The gaseous fluid flow confines the high temperature plasma inside the cavity and allows complete chemical processing of the gaseous fluids at a wide range of pressures.

  1. The NEXT experiment: A high pressure xenon gas TPC for neutrinoless double beta decay searches

    E-Print Network [OSTI]

    D. Lorca; J. Martín-Albo; F. Monrabal; for the NEXT Collaboration

    2012-10-15T23:59:59.000Z

    Neutrinoless double beta decay is a hypothetical, very slow nuclear transition in which two neutrons undergo beta decay simultaneously and without the emission of neutrinos. The importance of this process goes beyond its intrinsic interest: an unambiguous observation would establish a Majorana nature for the neutrino and prove the violation of lepton number. NEXT is a new experiment to search for neutrinoless double beta decay using a radiopure high-pressure xenon gas TPC, filled with 100 kg of Xe enriched in Xe-136. NEXT will be the first large high-pressure gas TPC to use electroluminescence readout with SOFT (Separated, Optimized FuncTions) technology. The design consists in asymmetric TPC, with photomultipliers behind a transparent cathode and position-sensitive light pixels behind the anode. The experiment is approved to start data taking at the Laboratorio Subterr\\'aneo de Canfranc (LSC), Spain, in 2014.

  2. High-Q silica zipper cavity for optical radiation pressure driven MOMS switch

    SciTech Connect (OSTI)

    Tetsumoto, Tomohiro; Tanabe, Takasumi, E-mail: takasumi@elec.keio.ac.jp [Department of Electronics and Electrical Engineering, Faculty of Science and Technology, Keio University, 3-14-1 Hiyoshi Kohoku, Yokohama 223-8522 (Japan)

    2014-07-15T23:59:59.000Z

    We design a silica zipper cavity that has high optical and mechanical Q (quality factor) values and demonstrate numerically the feasibility of a radiation pressure driven micro opto-mechanical system (MOMS) directional switch. The silica zipper cavity has an optical Q of 4.0 × 10{sup 4} and an effective mode volume V{sub mode} of 0.67?{sup 3} when the gap between two cavities is 34 nm. The mechanical Q (Q{sub m}) is determined by thermo-elastic damping and is 2.0 × 10{sup 6} in a vacuum at room temperature. The opto-mechanical coupling rate g{sub OM} is as high as 100 GHz/nm, which allows us to move the directional cavity-waveguide system and switch 1550-nm light with 770-nm light by controlling the radiation pressure.

  3. Ground state properties and high pressure behavior of plutonium dioxide: Systematic density functional calculations

    E-Print Network [OSTI]

    Zhang, Ping; Zhao, Xian-Geng

    2010-01-01T23:59:59.000Z

    Plutonium dioxide is of high technological importance in nuclear fuel cycle and is particularly crucial in long-term storage of Pu-based radioactive waste. Using first-principles density-functional theory, in this paper we systematically study the structural, electronic, mechanical, thermodynamic properties, and pressure induced structural transition of PuO$_{2}$. To properly describe the strong correlation in the Pu $5f$ electrons, the local density approximation$+U$ and the generalized gradient approximation$+U$ theoretical formalisms have been employed. We optimize the $U$ parameter in calculating the total energy, lattice parameters, and bulk modulus at the nonmagnetic, ferromagnetic, and antiferromagnetic configurations for both ground state fluorite structure and high pressure cotunnite structure. The best agreement with experiments is obtained by tuning the effective Hubbard parameter $U$ at around 4 eV within the LDA$+U$ approach. After carefully testing the validity of the ground state, we further in...

  4. Vapor deposition of thin films

    DOE Patents [OSTI]

    Smith, David C. (Los Alamos, NM); Pattillo, Stevan G. (Los Alamos, NM); Laia, Jr., Joseph R. (Los Alamos, NM); Sattelberger, Alfred P. (Los Alamos, NM)

    1992-01-01T23:59:59.000Z

    A highly pure thin metal film having a nanocrystalline structure and a process of preparing such highly pure thin metal films of, e.g., rhodium, iridium, molybdenum, tungsten, rhenium, platinum, or palladium by plasma assisted chemical vapor deposition of, e.g., rhodium(allyl).sub.3, iridium(allyl).sub.3, molybdenum(allyl).sub.4, tungsten(allyl).sub.4, rhenium(allyl).sub.4, platinum(allyl).sub.2, or palladium(allyl).sub.2 are disclosed. Additionally, a general process of reducing the carbon content of a metallic film prepared from one or more organometallic precursor compounds by plasma assisted chemical vapor deposition is disclosed.

  5. Vapor-liquid equilibria for methanol + tetraethylene glycol dimethyl ether

    SciTech Connect (OSTI)

    Esteve, X.; Chaudhari, S.K.; Coronas, A. [Univ. Rovira i Virgili, Tarragona (Spain). Dept. of Electrical and Mechanical Engineering

    1995-11-01T23:59:59.000Z

    Vapor-liquid equilibrium (P-T-x) for the methanol + tetraethylene glycol dimethyl ether binary system were obtained by the static method in the range of temperatures from 293.15 to 423.15 K at 10 K intervals. The modified vapor pressure apparatus used is described. The Kuczynsky method was used to calculate the liquid and vapor composition and the activity coefficients of methanol from the initial composition of the sample and the measured pressure and temperature. The results were correlated by the NRTL and UNIQUAC temperature dependent activity coefficient models. This system shows nearly ideal behavior at 323.15 K, but positive deviations from ideality at lower temperatures and negative deviations at higher temperatures are observed. The activity coefficients become more negative with the increase in temperature and mole fraction of methanol. The excess molar enthalpy using the Gibss-Helmholtz equation and the NRTL and UNIQUAC parameters were calculated at 303.15 K and compared with experimental data. This binary system shows promise as a working pair for high-temperature heat pump applications.

  6. Transition in the deformation mode of nanocrystalline tantalum processed by high-pressure torsion

    SciTech Connect (OSTI)

    Ligda, J.P.; Schuster, B.E.; Wei, Q. (UNC)

    2012-10-11T23:59:59.000Z

    We present quasi-static room temperature compression and nanoindentation data for nanocrystalline and ultrafine grained tantalum processed by high-pressure torsion. Because bulk samples possess an inherent gradient in properties, microstructures were characterized using site-specific transmission electron microscopy and synchrotron X-ray diffraction. Nanocrystalline Ta shows appreciable homogeneous plastic deformation in compression; however, specimens with the smallest grain sizes exhibit localized plastic deformation via shear bands. Microstructural changes associated with this transition in deformation mode are discussed.

  7. Impedance-matching experiments using high-pressure, laser-driven shock waves

    SciTech Connect (OSTI)

    Veeser, L.R.; Reeves, G.A.; Holmes, N.C.; Trainor, R.J.; Anderson, R.A.

    1981-01-01T23:59:59.000Z

    A high-power laser was used to produce shock waves with pressures of 300 to 700 GPa. A series of impedance-matching experiments on aluminum-copper systems with 10% accuracy indicate several areas in which the experiment can be improved to reduce the errors. Several such improvements are now being made, including upgrading both the laser and recording systems and modifying the target characterization techniques.

  8. Engine having hydraulic and fan drive systems using a single high pressure pump

    DOE Patents [OSTI]

    Bartley, Bradley E. (Manito, IL); Blass, James R. (Bloomington, IL); Gibson, Dennis H. (Chillicothe, IL)

    2000-01-01T23:59:59.000Z

    An engine comprises a hydraulic system attached to an engine housing that includes a high pressure pump and a hydraulic fluid flowing through at least one passageway. A fan drive system is also attached to the engine housing and includes a hydraulic motor and a fan which can move air over the engine. The hydraulic motor includes an inlet fluidly connected to the at least one passageway.

  9. Modelling of noble anaesthetic gases and high hydrostatic pressure effects in lipid bilayers

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Moskovitz, Yevgeny [Department of Chemistry, Middle Tennessee State University; Yang, Hui [Department of Chemistry, Middle Tennessee State University

    2015-01-01T23:59:59.000Z

    Our objective was to study molecular processes that might be responsible for inert gas narcosis and high-pressure nervous syndrome. The classical molecular dynamics trajectories (200 ns-long) of dioleoylphosphatidylcholine (DOPC) bilayers simulated by the Berger force field were evaluated for water and the atomic distribution of noble gases around DOPC molecules at a pressure range of 1 - 1000 bar and temperature of 310 Kelvin. Xenon and argon have been tested as model gases for general anesthetics, and neon has been investigated for distortions that are potentially responsible for neurological tremor at hyperbaric conditions. The analysis of stacked radial pair distribution functions of DOPC headgroup atoms revealed the explicit solvation potential of gas molecules, which correlates with their dimensions. The orientational dynamics of water molecules at the biomolecular interface should be considered as an influential factor; while excessive solvation effects appearing in the lumen of membrane-embedded ion channels could be a possible cause of inert gas narcosis. All the noble gases tested exhibit similar patterns of the order parameter for both DOPC acyl chains, which is opposite to the patterns found for the order parameter curve at high hydrostatic pressures in intact bilayers. This finding supports the ‘critical volume’ hypothesis of anesthesia pressure reversal. The irregular lipid headgroup-water boundary observed in DOPC bilayers saturated with neon in the pressure range of 1 - 100 bar could be associated with the possible manifestation of neurological tremor at the atomic scale. The non-immobilizer neon also demonstrated the highest momentum impact on the normal component of the DOPC diffusion coefficient representing monolayers undulations rate, which indicates enhanced diffusivity, rather than atom size, as the key factor.

  10. Modelling of noble anaesthetic gases and high hydrostatic pressure effects in lipid bilayers

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Moskovitz, Yevgeny; Yang, Hui

    2015-01-01T23:59:59.000Z

    Our objective was to study molecular processes that might be responsible for inert gas narcosis and high-pressure nervous syndrome. The classical molecular dynamics trajectories (200 ns-long) of dioleoylphosphatidylcholine (DOPC) bilayers simulated by the Berger force field were evaluated for water and the atomic distribution of noble gases around DOPC molecules at a pressure range of 1 - 1000 bar and temperature of 310 Kelvin. Xenon and argon have been tested as model gases for general anesthetics, and neon has been investigated for distortions that are potentially responsible for neurological tremor at hyperbaric conditions. The analysis of stacked radial pair distributionmore »functions of DOPC headgroup atoms revealed the explicit solvation potential of gas molecules, which correlates with their dimensions. The orientational dynamics of water molecules at the biomolecular interface should be considered as an influential factor; while excessive solvation effects appearing in the lumen of membrane-embedded ion channels could be a possible cause of inert gas narcosis. All the noble gases tested exhibit similar patterns of the order parameter for both DOPC acyl chains, which is opposite to the patterns found for the order parameter curve at high hydrostatic pressures in intact bilayers. This finding supports the ‘critical volume’ hypothesis of anesthesia pressure reversal. The irregular lipid headgroup-water boundary observed in DOPC bilayers saturated with neon in the pressure range of 1 - 100 bar could be associated with the possible manifestation of neurological tremor at the atomic scale. The non-immobilizer neon also demonstrated the highest momentum impact on the normal component of the DOPC diffusion coefficient representing monolayers undulations rate, which indicates enhanced diffusivity, rather than atom size, as the key factor.« less

  11. Five-dimensional visualization of phase transition in BiNiO{sub 3} under high pressure

    SciTech Connect (OSTI)

    Liu, Yijin, E-mail: liuyijin@slac.stanford.edu, E-mail: wyang@ciw.edu [Stanford Synchrotron Radiation Lightsource, SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, California 94025 (United States); Wang, Junyue; Yang, Wenge, E-mail: liuyijin@slac.stanford.edu, E-mail: wyang@ciw.edu [Center of High Pressure Science and Technology Advanced Research (HPSTAR), Shanghai 201203 (China); High Pressure Synergetic Consortium, Geophysical Laboratory, Carnegie Institution of Washington, 9700 S Cass Avenue, Argonne, Illinois 60439 (United States); Azuma, Masaki [Materials and Structures Laboratory, Tokyo Institute of Technology, 4259 Nagatsuta, Yokohama 226-8503 (Japan); Mao, Wendy L. [Geological and Environmental Sciences, 450 Serra Mall, Stanford University, Stanford, California 94305 (United States); SLAC National Accelerator Laboratory, Stanford Institute for Materials and Energy Sciences, 2575 Sand Hill Road, Menlo Park, California 94025 (United States); Photon Science, SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, California 94025 (United States)

    2014-01-27T23:59:59.000Z

    Colossal negative thermal expansion was recently discovered in BiNiO{sub 3} associated with a low density to high density phase transition under high pressure. The varying proportion of co-existing phases plays a key role in the macroscopic behavior of this material. Here, we utilize a recently developed X-ray Absorption Near Edge Spectroscopy Tomography method and resolve the mixture of high/low pressure phases as a function of pressure at tens of nanometer resolution taking advantage of the charge transfer during the transition. This five-dimensional (X, Y, Z, energy, and pressure) visualization of the phase boundary provides a high resolution method to study the interface dynamics of high/low pressure phase.

  12. High-pressure shock behavior of WC and Ta2O5 powders.

    SciTech Connect (OSTI)

    Knudson, Marcus D. (Sandia National Laboratories, Albuquerque, NM); Reinhart, William Dodd (Sandia National Laboratories, Albuquerque, NM); Vogler, Tracy John; Root, Seth (Sandia National Laboratories, Albuquerque, NM)

    2011-10-01T23:59:59.000Z

    Planar shock experiments were conducted on granular tungsten carbide (WC) and tantalum oxide (Ta{sub 2}O{sub 5}) using the Z machine and a 2-stage gas gun. Additional shock experiments were also conducted on a nearly fully dense form of Ta{sub 2}O{sub 5}. The experiments on WC yield some of the highest pressure results for granular materials obtained to date. Because of the high distention of Ta{sub 2}O{sub 5}, the pressures obtained were significantly lower, but the very high temperatures generated led to large contributions of thermal energy to the material response. These experiments demonstrate that the Z machine can be used to obtain accurate shock data on granular materials. The data on Ta{sub 2}O{sub 5} were utilized in making improvements to the P-{lambda} model for high pressures; the model is found to capture the results not only of the Z and gas gun experiments but also those from laser experiments on low density aerogels. The results are also used to illustrate an approach for generating an equation of state using only the limited data coming from nanoindentation. Although the EOS generated in this manner is rather simplistic, for this material it gives reasonably good results.

  13. MEMS Lubrication by In-Situ Tribochemical Reactions From the Vapor Phase.

    SciTech Connect (OSTI)

    Dugger, Michael T.; Asay, David B.; Kim, Seong H.

    2008-01-01T23:59:59.000Z

    Vapor Phase Lubrication (VPL) of silicon surfaces with pentanol has been demonstrated. Two potential show stoppers with respect to application of this approach to real MEMS devices have been investigated. Water vapor was found to reduce the effectiveness of VPL with alcohol for a given alcohol concentration, but the basic reaction mechanism observed in water-free environments is still active, and devices operated much longer in mixed alcohol and water vapor environments than with chemisorbed monolayer lubricants alone. Complex MEMS gear trains were successfully lubricated with alcohol vapors, resulting in a factor of 104 improvement in operating life without failure. Complex devices could be made to fail if operated at much higher frequencies than previously used, and there is some evidence that the observed failure is due to accumulation of reaction products at deeply buried interfaces. However, if hypothetical reaction mechanisms involving heated surfaces are valid, then the failures observed at high frequency may not be relevant to operation at normal frequencies. Therefore, this work demonstrates that VPL is a viable approach for complex MEMS devices in conventional packages. Further study of the VPL reaction mechanisms are recommended so that the vapor composition may be optimized for low friction and for different substrate materials with potential application to conventionally fabricated, metal alloy parts in weapons systems. Reaction kinetics should be studied to define effective lubrication regimes as a function of the partial pressure of the vapor phase constituent, interfacial shear rate, substrate composition, and temperature.

  14. Ultra high pressure liquid chromatography column permeability and changes of the eluent properties

    SciTech Connect (OSTI)

    Gritti, Fabrice [University of Tennessee, Knoxville (UTK); Guiochon, Georges A [ORNL

    2008-01-01T23:59:59.000Z

    The behavior of four similar liquid chromatography columns (2.1 mm i.d. x30, 50, 100, and 150 mm, all packed with fine particles, average d{sub p} {approx} 1.7 {micro}m, of bridged ethylsiloxane/silica hybrid-C{sub 18}, named BEH-C{sub 18}) was studied in wide ranges of temperature and pressure. The pressure and the temperature dependencies of the viscosity and the density of the eluent (pure acetonitrile) along the columns were also derived, using the column permeabilities and applying the Kozeny-Carman and the heat balance equations. The heat lost through the external surface area of the chromatographic column was directly derived from the wall temperature of the stainless steel tube measured with a precision of C in still air and C in the oven compartment. The variations of the density and viscosity of pure acetonitrile as a function of the temperature and pressure was derived from empirical correlations based on precise experimental data acquired between 298 and 373 K and at pressures up to 1.5 kbar. The measurements were made with the Acquity UPLC chromatograph that can deliver a maximum flow rate of 2 mL/min and apply a maximum column inlet pressure of 1038 bar. The average Kozeny-Carman permeability constant of the columns was 144 {+-} 3.5%. The temperature hence the viscosity and the density profiles of the eluent along the column deviate significantly from linear behavior under high-pressure gradients. For a 1000 bar pressure drop, we measured {Delta}T = 25-30 K, ({Delta}{eta}/{eta}) {approx_equal} 100%, and ({Delta}{rho}/{rho}) {approx_equal} 10%. These results show that the radial temperature profiles are never fully developed within 1% for any of the columns, even under still-air conditions. This represents a practical advantage regarding the apparent column efficiency at high flow rates, since the impact of the differential analyte velocity between the column center and the column wall is not maximum. The interpretation of the peak profiles recorded in UPLC is discussed.

  15. Structure determination of the high-pressure phase of CdSe

    SciTech Connect (OSTI)

    Li, Yanchun, E-mail: liyc@ihep.ac.cn, E-mail: liuj@ihep.ac.cn; Lin, Chuanlong; Li, Xiaodong; Liu, Jing, E-mail: liyc@ihep.ac.cn, E-mail: liuj@ihep.ac.cn [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, Chinese Academy of Science, 100049 Beijing (China); Li, Gong [State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Xu, Jian [Institute of Fluid Physics, China Academy of Engineering Physics, P. O. Box 919-102, Mianyang, Sichuan 621900 (China)

    2014-06-14T23:59:59.000Z

    Structural phase transition sequence of CdSe has been investigated at pressures up to 60?GPa under quasi-hydrostatic conditions using synchrotron X-ray diffraction. A phase transition from the wurtzite type (B4) to the NaCl-type (B1) structure has been observed, followed by another phase transition to an orthorhombic structure at 27?GPa, in agreement with previous reports. We show that this high-pressure orthorhombic phase has a Pnma symmetry rather than being a Cmcm-symmetric structure as previously suggested. From our observations, the appearance of the new reflections and reflection splitting with increasing pressure is due to the change of atomic relative positions in crystal lattice and the difference in the compression ratio of lattice parameters for the Pnma structure, and we find no evidence for the third phase transition reported previously. The pressure-induced phase transition of CdSe has been further confirmed by the density-functional theory calculations.

  16. Diatomaceous earth and activated bauxite used as granular sorbents for the removal of sodium chloride vapor from hot flue gas

    SciTech Connect (OSTI)

    Lee, S.H.D.; Swift, W.M.; Johnson, I.

    1980-01-01T23:59:59.000Z

    Diatomaceous earth and activated bauxite were tested as granular sorbents for use as filter media in granular-bed filters for the removal of gaseous alkali metal compounds from the hot (800/sup 0/C) flue gas of PFBC. Tests were performed at atmospheric pressure, using NaCl vapor transported in relatively dry simulated flue gas of PFBC. Either a fixed-bed combustor or a high-temperature sorption test rig was used. The effects of sorbent bed temperature, superficial gas velocity, gas hourly space velocity, and NaCl-vapor concentration in flue gas on the sorption behavior of these two sorbents and their ultimate sorption capacities were determined. Both diatomaceous earth and activated bauxite were found to be very effective in removing NaCl vapor from flue gas. Preliminary cost evaluations showed that they are economically attractive as granular sorbents for cleaning alkali vapor from simulated flue gas.

  17. The ReactorSTM: Atomically resolved scanning tunneling microscopy under high-pressure, high-temperature catalytic reaction conditions

    SciTech Connect (OSTI)

    Herbschleb, C. T.; Tuijn, P. C. van der; Roobol, S. B.; Navarro, V.; Bakker, J. W.; Liu, Q.; Stoltz, D.; Cañas-Ventura, M. E.; Verdoes, G.; Spronsen, M. A. van; Bergman, M.; Crama, L.; Taminiau, I.; Frenken, J. W. M., E-mail: frenken@physics.leidenuniv.nl [Huygens-Kamerlingh Onnes Laboratory, Leiden University, P.O. box 9504, 2300 RA Leiden (Netherlands); Ofitserov, A.; Baarle, G. J. C. van [Leiden Probe Microscopy B.V., J.H. Oortweg 21, 2333 CH Leiden (Netherlands)

    2014-08-15T23:59:59.000Z

    To enable atomic-scale observations of model catalysts under conditions approaching those used by the chemical industry, we have developed a second generation, high-pressure, high-temperature scanning tunneling microscope (STM): the ReactorSTM. It consists of a compact STM scanner, of which the tip extends into a 0.5 ml reactor flow-cell, that is housed in a ultra-high vacuum (UHV) system. The STM can be operated from UHV to 6 bars and from room temperature up to 600 K. A gas mixing and analysis system optimized for fast response times allows us to directly correlate the surface structure observed by STM with reactivity measurements from a mass spectrometer. The in situ STM experiments can be combined with ex situ UHV sample preparation and analysis techniques, including ion bombardment, thin film deposition, low-energy electron diffraction and x-ray photoelectron spectroscopy. The performance of the instrument is demonstrated by atomically resolved images of Au(111) and atom-row resolution on Pt(110), both under high-pressure and high-temperature conditions.

  18. Characterization and modeling of ferroelectric materials for high pressure, high temperature applications

    E-Print Network [OSTI]

    VALADEZ PEREZ, JUAN CARLOS

    2012-01-01T23:59:59.000Z

    Applications in the Aerospace and automotive industrytemperature, etc. In the automotive industry is a similarThe automotive and aerospace industries also require high

  19. Apparatus and method for fatigue testing of a material specimen in a high-pressure fluid environment

    DOE Patents [OSTI]

    Wang, Jy-An; Feng, Zhili; Anovitz, Lawrence M; Liu, Kenneth C

    2013-06-04T23:59:59.000Z

    The invention provides fatigue testing of a material specimen while the specimen is disposed in a high pressure fluid environment. A specimen is placed between receivers in an end cap of a vessel and a piston that is moveable within the vessel. Pressurized fluid is provided to compression and tension chambers defined between the piston and the vessel. When the pressure in the compression chamber is greater than the pressure in the tension chamber, the specimen is subjected to a compression force. When the pressure in the tension chamber is greater than the pressure in the compression chamber, the specimen is subjected to a tension force. While the specimen is subjected to either force, it is also surrounded by the pressurized fluid in the tension chamber. In some examples, the specimen is surrounded by hydrogen.

  20. Use of high hydrostatic pressure to produce high quality and safe fresh pork sausage

    E-Print Network [OSTI]

    Huang, Mei

    1997-01-01T23:59:59.000Z

    -life of the product. With most spoilage organisms being killed after exposure to 63- 65'C for 45 min or longer. For highly resistant organisms exposure of 65-68'C (internal temperature) is needed . Clean product with low initial baterial load, low pH, and high salt...

  1. Atmospheric pressure plasma jet with high-voltage power supply based on piezoelectric transformer

    SciTech Connect (OSTI)

    Babij, Micha?; Kowalski, Zbigniew W., E-mail: zbigniew.w.kowalski@pwr.wroc.pl; Nitsch, Karol; Gotszalk, Teodor [Wroc?aw University of Technology, Wybrze?e Wyspia?skiego 27, 50-370 Wroc?aw (Poland)] [Wroc?aw University of Technology, Wybrze?e Wyspia?skiego 27, 50-370 Wroc?aw (Poland); Silberring, Jerzy [AGH University of Science and Technology, Al. A. Mickiewicza 30, 30-059 Kraków (Poland)] [AGH University of Science and Technology, Al. A. Mickiewicza 30, 30-059 Kraków (Poland)

    2014-05-15T23:59:59.000Z

    The dielectric barrier discharge plasma jet, an example of the nonthermal atmospheric pressure plasma jet (APPJ), generates low-temperature plasmas that are suitable for the atomization of volatile species and can also be served as an ionization source for ambient mass and ion mobility spectrometry. A new design of APPJ for mass spectrometry has been built in our group. In these plasma sources magnetic transformers (MTs) and inductors are typically used in power supplies but they present several drawbacks that are even more evident when dealing with high-voltage normally used in APPJs. To overcome these disadvantages, high frequency generators with the absence of MT are proposed in the literature. However, in the case of miniaturized APPJs these conventional power converters, built of ferromagnetic cores and inductors or by means of LC resonant tank circuits, are not so useful as piezoelectric transformer (PT) based power converters due to bulky components and small efficiency. We made and examined a novel atmospheric pressure plasma jet with PT supplier served as ionization source for ambient mass spectrometry, and especially mobile spectrometry where miniaturization, integration of components, and clean plasma are required. The objective of this paper is to describe the concept, design, and implementation of this miniaturized piezoelectric transformer-based atmospheric pressure plasma jet.

  2. Simplified configuration for the combustor of an oil burner using a low pressure, high flow air-atomizing nozzle

    DOE Patents [OSTI]

    Butcher, Thomas A. (Port Jefferson, NY); Celebi, Yusuf (Middle Island, NY); Fisher, Leonard (Colrain, MA)

    2000-09-15T23:59:59.000Z

    The invention relates to clean burning of fuel oil with air. More specifically, to a fuel burning combustion head using a low-pressure, high air flow atomizing nozzle so that there will be a complete combustion of oil resulting in a minimum emission of pollutants. The improved fuel burner uses a low pressure air atomizing nozzle that does not result in the use of additional compressors or the introduction of pressurized gases downstream, nor does it require a complex design. Inventors:

  3. A New Scanning Tunneling Microscope Reactor Used for High Pressure and High Temperature Catalysis Studies

    E-Print Network [OSTI]

    Tao, Feng

    2009-01-01T23:59:59.000Z

    bowl glued at the end of the scanning tube. The arrowbowl at the end of the scanning tube. FIG. 6. (a) STM imageA New Scanning Tunneling Microscope Reactor Used for High

  4. Dark Matter Directionality Revisited with a High Pressure Xenon Gas Detector

    E-Print Network [OSTI]

    Gopolang Mohlabeng; Kyoungchul Kong; Jin Li; Adam Para; Jonghee Yoo

    2015-04-29T23:59:59.000Z

    An observation of the anisotropy of dark matter interactions in a direction-sensitive detector would provide decisive evidence for the discovery of galactic dark matter. Directional information would also provide a crucial input to understanding its distribution in the local Universe. Most of the existing directional dark matter detectors utilize particle tracking methods in a low-pressure gas time projection chamber. These low pressure detectors require excessively large volumes in order to be competitive in the search for physics beyond the current limit. In order to avoid these volume limitations, we consider a novel proposal, which exploits a columnar recombination effect in a high-pressure gas time projection chamber. The ratio of scintillation to ionization signals observed in the detector carries the angular information of the particle interactions. In this paper, we investigate the sensitivity of a future directional detector focused on the proposed high-pressure Xenon gas time projection chamber. We study the prospect of detecting an anisotropy in the dark matter velocity distribution. We find that tens of events are needed to exclude an isotropic distribution of dark matter interactions at 95% confidence level in the most optimistic case with head-to-tail information. However, one needs at least 10-20 times more events without head-to-tail information for light dark matter below 50 GeV. For an intermediate mass range, we find it challenging to observe an anisotropy of the dark matter distribution. Our results also show that the directional information significantly improves precision measurements of dark matter mass and the elastic scattering cross section for a heavy dark matter.

  5. Image Storage in Hot Vapors

    E-Print Network [OSTI]

    L. Zhao; T. Wang; Y. Xiao; S. F. Yelin

    2007-10-22T23:59:59.000Z

    We theoretically investigate image propagation and storage in hot atomic vapor. A $4f$ system is adopted for imaging and an atomic vapor cell is placed over the transform plane. The Fraunhofer diffraction pattern of an object in the object plane can thus be transformed into atomic Raman coherence according to the idea of ``light storage''. We investigate how the stored diffraction pattern evolves under diffusion. Our result indicates, under appropriate conditions, that an image can be reconstructed with high fidelity. The main reason for this procedure to work is the fact that diffusion of opposite-phase components of the diffraction pattern interfere destructively.

  6. Method of physical vapor deposition of metal oxides on semiconductors

    DOE Patents [OSTI]

    Norton, David P. (Knoxville, TN)

    2001-01-01T23:59:59.000Z

    A process for growing a metal oxide thin film upon a semiconductor surface with a physical vapor deposition technique in a high-vacuum environment and a structure formed with the process involves the steps of heating the semiconductor surface and introducing hydrogen gas into the high-vacuum environment to develop conditions at the semiconductor surface which are favorable for growing the desired metal oxide upon the semiconductor surface yet is unfavorable for the formation of any native oxides upon the semiconductor. More specifically, the temperature of the semiconductor surface and the ratio of hydrogen partial pressure to water pressure within the vacuum environment are high enough to render the formation of native oxides on the semiconductor surface thermodynamically unstable yet are not so high that the formation of the desired metal oxide on the semiconductor surface is thermodynamically unstable. Having established these conditions, constituent atoms of the metal oxide to be deposited upon the semiconductor surface are directed toward the surface of the semiconductor by a physical vapor deposition technique so that the atoms come to rest upon the semiconductor surface as a thin film of metal oxide with no native oxide at the semiconductor surface/thin film interface. An example of a structure formed by this method includes an epitaxial thin film of (001)-oriented CeO.sub.2 overlying a substrate of (001) Ge.

  7. Synthesis, structural characterization and high pressure phase transitions of monolithium hydronium sulfate

    SciTech Connect (OSTI)

    Banerjee, Debasis, E-mail: debasis.banerjee@stonybrook.edu [Department of Chemistry, Stony Brook University, Stony Brook 11794-3400 (United States); Plonka, Anna M. [Department of Geosciences, Stony Brook University, Stony Brook 11794-2100 (United States); Kim, Sun Jin [Nano-Materials Research Center, Korea Institute of Science and Technology, P.O. Box 131, Cheongryang, Seoul 130-650 (Korea, Republic of); Xu Wenqian [Department of Geosciences, Stony Brook University, Stony Brook 11794-2100 (United States); Parise, John B. [Department of Chemistry, Stony Brook University, Stony Brook 11794-3400 (United States); Mineral Physics Institute, Stony Brook University, Stony Brook, NY 11790-2100 (United States)

    2013-01-15T23:59:59.000Z

    A three dimensional lithium hydronium sulfate LiSO{sub 4}{center_dot}H{sub 3}O [1], [space group Pna2{sub 1}a=8.7785(12) A, b=9.1297(12) A, c=5.2799(7) A, V=423.16(10) A{sup 3}] was synthesized via solvothermal methods using 1,5-naphthalenedisulfonic acid (1,5-NSA) as the source of sulfate ions. The structure of [1], determined by single crystal X-ray diffraction techniques, consists of corner sharing LiO{sub 4} and SO{sub 4} tetrahedra, forming an anionic 3-D open framework that is charge balanced by hydronium ions positioned within channels running along [001] and forming strong H-bonding with the framework oxygen atoms. Compound [1] undergoes two reversible phase transitions, involving reorientation of SO{sub 4}{sup 2-} ions at pressures of approximately 2.5 and 5 GPa at room temperature, as evident from characteristic discontinuous frequency drops in the {nu}{sub 1} mode of the Raman spectra. Additionally, compound [1] forms dense {beta}-lithium sulfate at 300 Degree-Sign C, as evident from temperature dependent powder XRD and combined reversible TGA-DSC experiments. - Graphical abstract: Left: View of corner-shared LiO{sub 4} and SO{sub 4} tetrahedra along [001] direction with hydronium ions situated in the channels. Right: (a) Photograph of the loaded DAC (b) Ambient pressure Raman spectrum of compound [1] (c) Evolution of the {nu}{sub 1} mode with the increasing and decreasing pressure indicating transitions to high-pressure phases at {approx}2.5 (red curves) and {approx}5 GPa (blue curves) and at {approx}3.5 GPa upon decompression. Highlights: Black-Right-Pointing-Pointer A 3-D lithium hydronium sulfate is synthesized by solvothermal methods. Black-Right-Pointing-Pointer Two high pressure phase transition occurs due to rotation of sulfate groups. Black-Right-Pointing-Pointer The framework undergoes a high temperature structural transformation, to form {beta}-Li{sub 2}SO{sub 4} phase.

  8. Photoluminescence studies of Y{sub 2}O{sub 3}:Eu{sup 3+} under high pressure

    SciTech Connect (OSTI)

    Zhang, Jian; Cui, Hang; Ma, Chunli; Wu, Xiaoxin; Cui, Qiliang [State Key Laboratory of Superhard Materials, Jilin University, Changchun, Jilin 130012 (China); Zhu, Peifen [Department of Electrical and Computer Engineering, Lehigh University, Bethlehem, Pennsylvania 18015 (United States); Zhu, Hongyang, E-mail: hongyangzhu@jlu.edu.cn [State Key Laboratory of Superhard Materials, Jilin University, Changchun, Jilin 130012 (China); College of Materials Science and Engineering, Jilin University, Changchun, Jilin 130012 (China); Ma, Yanzhang [Department of Mechanical Engineering, Texas Tech University, Lubbock, Texas 79409 (United States)

    2014-01-14T23:59:59.000Z

    The Eu-doped yttria (Y{sub 2}O{sub 3}:Eu{sup 3+}) has been investigated by the in situ high-pressure angle dispersive synchrotron X-ray diffraction (XRD) and the photoluminescence (PL) spectroscopy. The red shift and intensity ratio variation of emissions with increasing pressure were observed and elucidated. It was found that the red shift of emissions is related to the expansion of the f orbit of the Eu{sup 3+} and the intensity ratio variation of emissions is ascribed to the change of the crystal field under high pressure. The pressure-induced changes in spectrum are related to the phase transition, which was confirmed by XRD pattern. The two high pressure phases were identified as the monoclinic (C2/m) phase and hexagonal (P-3m1) phase by the Rietveld refinement.

  9. High-temperature characteristics of Seebeck coefficients for AlInN alloys grown by metalorganic vapor phase epitaxy

    E-Print Network [OSTI]

    Gilchrist, James F.

    importance for efficient thermal management in high power devices. The availability of III- nitride the calculation of surface and interface energies J. Appl. Phys. 110, 113910 (2011) A strain relief mode of Physics. [doi:10.1063/1.3624761] I. INTRODUCTION High power density and high-temperature requirements

  10. High temperature mass spectrometric investigation of the equilibrium vapor composition over three-component mixtures of CsI, NaI, and DyI/sub 3/

    SciTech Connect (OSTI)

    Kaposi, O.; Szilagyi, J.; Lelik, L.

    1984-10-01T23:59:59.000Z

    The molar composition of the saturated vapor phase over ternary iodides of CsI, NaI, and DyI/sub 3/ at 860 to 1060 K was investigated by means of a mass spectrometer equipped with a Knudsen cell evaporator system. Fragmentation patterns and appearance potentials for the most intense ions were determined. Besides the previously detected fragments in the equilibrium vapor above the two-component systems, fragment ions from the complex molecules NaCsDyI/sub 5/, Na/sub 2/CsDyI/sub 6/, NaCs/sub 2/DyI/sub 6/, and Na/sub 3/Cs/sub 2/DyI/sub 8/ were found. Ion current vs temperature data yielded heats of sublimation: ..delta..H/sub s/ (NaCsDyI/sub 5/)/sub 960K/ = 320 +/- 13 kJ/mol; ..delta..H/sub s/ (Na/sub 2/CsDyI/sub 6/)/sub 960K/ = 325 +/- 11 kJ/mol; ..delta..H/sub s/ (NaCs/sub 2/DyI/sub 6/)/sub 960K/ = 348 +/- 15 kJ/mol; and ..delta..H/sub s/ (Na/sub 3/Cs/sub 2/DyI/sub 8/)/sub 960K/ = 366 +/- 17 kJ/mol. From the various high-temperature equilibrium reactions, one may calculate the following heats of formation: ..delta..H/sub f/ (NaCsDyI/sub 5/)/sub g/ = -863 +/- 23 kJ/mol; ..delta..H/sub f/ (Na/sub 2/CsDyI/sub 6/)/sub g/ = -1170 +/- 31 kJ/mol; ..delta..H/sub f/ (NaCs/sub 2/DyI/sub 6/)/sub g/ = -1235 +/- 33 kJ/mol; and ..delta..H/sub f/ (Na/sub 3/Cs/sub 2/DyI/sub 8/) = -1806 +/- 17 kJ/mol.

  11. Complete temperature profiles in ultra-high pressure liquid chromatography columns

    SciTech Connect (OSTI)

    Gritti, Fabrice [University of Tennessee, Knoxville (UTK); Guiochon, Georges A [ORNL

    2008-01-01T23:59:59.000Z

    The temperature profiles were calculated along and across seven packed columns (lengths 30, 50, 100, and 150 mm, i.d., 1 and 2.1 mm, all packed with Acquity UPLC, BEH-C{sub 18} particles, average d{sub p} {approx} 1.7 {micro}m) and their stainless steel tubes (o.d. 4.53 and 6.35 mm). These columns were kept horizontal and sheltered from forced air convection (i.e., under still air conditions), at room temperature. They were all percolated with pure acetonitrile, either under the maximum pressure drop (1034 bar) or at the maximum flow rate (2 mL/min) permitted by the chromatograph. The heat balance equation of chromatographic columns was discretized and solved numerically with minimum approximation. Both the compressibility and the thermal expansion of the eluent were taken into account. The boundary conditions were determined from the experimental measurements of the column inlet pressure and of the temperature profile along the column wall, which were made with a precision better than {+-}0.1 K. These calculation results provide the 3-D temperature profiles along and across the columns. The axial and radial temperature gradients are discussed in relationship with the experimental conditions used. The temperature map obtained permits a prediction of the chromatographic data obtained under a very high pressure gradient.

  12. In-situ Phase Transformation and Deformation of Iron at High Pressure andTemperature

    SciTech Connect (OSTI)

    Miyagi, Lowell; Kunz, Martin; Knight, Jason; Nasiatka, James; Voltolini, Marco; Wenk, Hans-Rudolf

    2008-07-01T23:59:59.000Z

    With a membrane based mechanism to allow for pressure change of a sample in aradial diffraction diamond anvil cell (rDAC) and simultaneous infra-red laser heating, itis now possible to investigate texture changes during deformation and phasetransformations over a wide range of temperature-pressure conditions. The device isused to study bcc (alpha), fcc (gamma) and hcp (epislon) iron. In bcc iron, room temperature compression generates a texture characterized by (100) and (111) poles parallel to the compression direction. During the deformation induced phase transformation to hcp iron, a subset of orientations are favored to transform to the hcp structure first and generate a texture of (01-10) at high angles to the compression direction. Upon further deformation, the remaining grains transform, resulting in a texture that obeys the Burgers relationship of (110)bcc // (0001)hcp. This is in contrast to high temperature results that indicate that texture is developed through dominant pyramidal {2-1-12}<2-1-13> and basal (0001)-{2-1-10} slip based on polycrystal plasticity modeling. We also observe that the high temperature fcc phase develops a 110 texture typical for fcc metals deformed in compression.

  13. Vapor spill pipe monitor

    DOE Patents [OSTI]

    Bianchini, G.M.; McRae, T.G.

    1983-06-23T23:59:59.000Z

    The invention is a method and apparatus for continually monitoring the composition of liquefied natural gas flowing from a spill pipe during a spill test by continually removing a sample of the LNG by means of a probe, gasifying the LNG in the probe, and sending the vaporized LNG to a remote ir gas detector for analysis. The probe comprises three spaced concentric tubes surrounded by a water jacket which communicates with a flow channel defined between the inner and middle, and middle and outer tubes. The inner tube is connected to a pump for providing suction, and the probe is positioned in the LNG flow below the spill pipe with the tip oriented partly downward so that LNG is continuously drawn into the inner tube through a small orifice. The probe is made of a high thermal conductivity metal. Hot water is flowed through the water jacket and through the flow channel between the three tubes to provide the necessary heat transfer to flash vaporize the LNG passing through the inner channel of the probe. The gasified LNG is transported through a connected hose or tubing extending from the probe to a remote ir sensor which measures the gas composition.

  14. A field-deployable gamma-ray spectrometer utilizing xenon at high pressure

    SciTech Connect (OSTI)

    Smith, G.C.; Mahler, G.J.; Yu, B.; Salwen, C.; Kane, W.R.; Lemley, J.R.

    1996-10-01T23:59:59.000Z

    Prototype gamma-ray spectrometers utilizing xenon gas at high pressure, suitable for applications in the nuclear safeguards, arms control, and nonproliferation communities, have been developed at Brookhaven National Laboratory (BNL). These spectrometers function as ambient-temperature ionization chambers detecting gamma rays with good efficiency in the energy range 50 keV - 2 MeV, with an energy resolution intermediate between semiconductor (Ge) and scintillation (NaI) spectrometers. They are capable of prolonged, low-power operation without a requirement for cryogenic fluids or other cooling mechanisms, and with the addition of small quantities of {sup 3}He gas, can function simultaneously as efficient thermal neutron detectors.

  15. Dislocation density evolution during high pressure torsion of a nanocrystalline Ni-Fe alloy

    SciTech Connect (OSTI)

    Li, Hongqi [Los Alamos National Laboratory; Wang, Y B [NON LANL; Ho, J C [NON LANL; Cao, Y [NON LANL; Liao, X Z [NON LANL; Ringer, S P [NON LANL; Zhu, Y T [NON LANL; Zhao, Y H [NON LANL; Lavernia, E J [NON LANL

    2009-01-01T23:59:59.000Z

    High-pressure torsion (HPT) induced dislocation density evolution in a nanocrystalline Ni-20wt.%Fe alloy was investigated using X-ray diffraction and transmission electron microscopy. Results suggest that the dislocation density evolution is different from that in coarse-grained materials. An HPT process first reduces the dislocation density within nanocrystalline grains and produces a large number of dislocations located at small-angle sub grain boundaries that are formed via grain rotation and coalescence. Continuing the deformation process eliminates the sub grain boundaries but significantly increases the dislocation density in grains. This phenomenon provides an explanation of the mechanical behavior of some nanostructured materials.

  16. Low loss hollow optical-waveguide connection from atmospheric pressure to ultra-high vacuum

    SciTech Connect (OSTI)

    Ermolov, A.; Mak, K. F.; Tani, F.; Hölzer, P.; Travers, J. C. [Max Planck Institute for the Science of Light, Günther-Scharowsky-Str. 1, 91058 Erlangen (Germany)] [Max Planck Institute for the Science of Light, Günther-Scharowsky-Str. 1, 91058 Erlangen (Germany); Russell, P. St. J. [Max Planck Institute for the Science of Light, Günther-Scharowsky-Str. 1, 91058 Erlangen (Germany) [Max Planck Institute for the Science of Light, Günther-Scharowsky-Str. 1, 91058 Erlangen (Germany); Department of Physics, University of Erlangen-Nuremberg, Günther-Scharowsky-Str. 1, 91058 Erlangen (Germany)

    2013-12-23T23:59:59.000Z

    A technique for optically accessing ultra-high vacuum environments, via a photonic-crystal fiber with a long small hollow core, is described. The small core and the long bore enable a pressure ratio of over 10{sup 8} to be maintained between two environments, while permitting efficient and unimpeded delivery of light, including ultrashort optical pulses. This delivery can be either passive or can encompass nonlinear optical processes such as optical pulse compression, deep UV generation, supercontinuum generation, or other useful phenomena.

  17. Energy distribution and computer modeled nozzle design in high pressure water jet coating removal

    SciTech Connect (OSTI)

    Blades, B. [Hobart Tafa Technologies Inc., Concord, NH (United States)

    1994-12-31T23:59:59.000Z

    Wider acceptance of water jet coating removal as an industrial process has created a demand to better understand the physical phenomena occurring during coating removal. This demand stems from both technical and process control concerns. Research on behavior of coating removal nozzles and high pressure jets in general provide the basis for the development of a mathematical model of rotating nozzle. The model finds uses in both process development and new equipment design. Data confirming the validity of the model has been generated and the need for further refinement of the model has been noted.

  18. Warm-Intermediate Inflationary Universe Model with Viscous Pressure in High Dissipative Regime

    E-Print Network [OSTI]

    M. R. Setare; V. Kamali

    2014-03-02T23:59:59.000Z

    Warm inflation model with bulk viscous pressure in the context of "intermediate inflation" where the cosmological scale factor expands as $a(t)=a_0\\exp(At^f)$, is studied. The characteristics of this model in slow-roll approximation and in high dissipative regime are presented in two cases: 1- Dissipative parameter $\\Gamma$ as a function of scalar field $\\phi$ and bulk viscous coefficient $\\zeta$ as a function of energy density $\\rho$. 2- $\\Gamma$ and $\\zeta$ are constant parameters. Scalar, tensor perturbations and spectral indices for this scenario are obtained. The cosmological parameters appearing in the present model are constrained by recent observational data (WMAP7).

  19. Warm-Intermediate Inflationary Universe Model with Viscous Pressure in High Dissipative Regime

    E-Print Network [OSTI]

    Setare, M R

    2014-01-01T23:59:59.000Z

    Warm inflation model with bulk viscous pressure in the context of "intermediate inflation" where the cosmological scale factor expands as $a(t)=a_0\\exp(At^f)$, is studied. The characteristics of this model in slow-roll approximation and in high dissipative regime are presented in two cases: 1- Dissipative parameter $\\Gamma$ as a function of scalar field $\\phi$ and bulk viscous coefficient $\\zeta$ as a function of energy density $\\rho$. 2- $\\Gamma$ and $\\zeta$ are constant parameters. Scalar, tensor perturbations and spectral indices for this scenario are obtained. The cosmological parameters appearing in the present model are constrained by recent observational data (WMAP7).

  20. Inside Ice Under High Pressure | U.S. DOE Office of Science (SC)

    Office of Science (SC) Website

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What'sis Taking Over OurTheBrookhaven National LaboratoryJeffrey L80'sInside Ice Under High Pressure

  1. Method and apparatus for pressurizing vaporous fluids

    DOE Patents [OSTI]

    Bingham, Dennis N. (Idaho Falls, ID); Ferguson, Russell L. (Idaho Falls, ID)

    2001-01-01T23:59:59.000Z

    Pump apparatus according to the present invention may comprise a pump body having a bore therein and a piston mounted within the bore so that the piston may be reciprocated within the bore between first and second positions. A sleeve seal assembly mounted to the pump body contacts the piston as the piston moves between the first and second positions. A piston seal assembly mounted to the piston contacts the bore in the pump body and is located on the piston so that the piston seal assembly does not contact the sleeve seal assembly as the piston is reciprocated between the first and second positions within the bore of the pump body.

  2. The etching process of boron nitride by alkali and alkaline earth fluorides under high pressure and high temperature

    SciTech Connect (OSTI)

    Guo, W., E-mail: guowei1982cry@163.com [College of Physics and Optoelectronics, Taiyuan University of Technology, Taiyuan 030024 (China); National Key Lab of Superhard Materials, Jilin University, Changchun 130012 (China); Ma, H.A.; Jia, X. [National Key Lab of Superhard Materials, Jilin University, Changchun 130012 (China)

    2014-03-01T23:59:59.000Z

    Graphical abstract: - Highlights: • Appropriate etch processes of hBN and cBN under HPHT are proposed. • The degree of the crystallization of hBN was decreased. • A special cBN growth mechanism with a triangular unit is proposed. • Plate-shape cBN crystals with large ratio of length to thickness were obtained. • A strategy provides useful guidance for controlling the cBN morphology. - Abstract: Some new etching processes of hexagonal boron nitride (hBN) and cubic boron nitride (cBN) under high pressure and high temperature in the presence of alkali and alkaline earth fluorides have been discussed. It is found that hBN is etched distinctly by alkali and alkaline earth fluorides and the morphology of hBN is significantly changed from plate-shape to spherical-shape. Based on the “graphitization index” values of hBN, the degree of the crystallization of hBN under high pressure and high temperature decreases in the sequence of LiF > CaF{sub 2} > MgF{sub 2}. This facilitates the formation of high-quality cBN single crystals. Different etch steps, pits, and islands are observed on cBN surface, showing the strong etching by alkali and alkaline earth fluorides and the tendency of layer-by-layer growth. A special layer growth mechanism of cBN with a triangular unit has been found. Furthermore, the morphologies of cBN crystals are apparently affected by a preferential surface etching of LiF, CaF{sub 2} and MgF{sub 2}. Respectively, the plate-shape and tetrahedral cBN crystals can be obtained in the presence of different alkali and alkaline earth fluorides.

  3. All graphene electromechanical switch fabricated by chemical vapor deposition

    E-Print Network [OSTI]

    Milaninia, Kaveh M.

    We demonstrate an electromechanical switch comprising two polycrystalline graphene films; each deposited using ambient pressure chemical vapor deposition. The top film is pulled into electrical contact with the bottom film ...

  4. High speed door assembly

    DOE Patents [OSTI]

    Shapiro, C.

    1993-04-27T23:59:59.000Z

    A high speed door assembly is described, comprising an actuator cylinder and piston rods, a pressure supply cylinder and fittings, an electrically detonated explosive bolt, a honeycomb structured door, a honeycomb structured decelerator, and a structural steel frame encasing the assembly to close over a 3 foot diameter opening within 50 milliseconds of actuation, to contain hazardous materials and vapors within a test fixture.

  5. High speed door assembly

    DOE Patents [OSTI]

    Shapiro, Carolyn (Idaho Falls, ID)

    1993-01-01T23:59:59.000Z

    A high speed door assembly, comprising an actuator cylinder and piston rods, a pressure supply cylinder and fittings, an electrically detonated explosive bolt, a honeycomb structured door, a honeycomb structured decelerator, and a structural steel frame encasing the assembly to close over a 3 foot diameter opening within 50 milliseconds of actuation, to contain hazardous materials and vapors within a test fixture.

  6. A compact bellows-driven diamond anvil cell for high-pressure, low-temperature magnetic measurements

    SciTech Connect (OSTI)

    Feng, Yejun [The Advanced Photon Source, Argonne National Laboratory, Argonne, Illinois 60439 (United States) [The Advanced Photon Source, Argonne National Laboratory, Argonne, Illinois 60439 (United States); The James Franck Institute and Department of Physics, The University of Chicago, Chicago, Illinois 60637 (United States); Silevitch, D. M.; Rosenbaum, T. F. [The James Franck Institute and Department of Physics, The University of Chicago, Chicago, Illinois 60637 (United States)] [The James Franck Institute and Department of Physics, The University of Chicago, Chicago, Illinois 60637 (United States)

    2014-03-15T23:59:59.000Z

    We present the design of an efficient bellows-controlled diamond anvil cell that is optimized for use inside the bores of high-field superconducting magnets in helium-3 cryostats, dilution refrigerators, and commercial physical property measurement systems. Design of this non-magnetic pressure cell focuses on in situ pressure tuning and measurement by means of a helium-filled bellows actuator and fiber-coupled ruby fluorescence spectroscopy, respectively. We demonstrate the utility of this pressure cell with ac susceptibility measurements of superconducting, ferromagnetic, and antiferromagnetic phase transitions to pressures exceeding 8 GPa. This cell provides an opportunity to probe charge and magnetic order continuously and with high resolution in the three-dimensional Magnetic Field–Pressure–Temperature parameter space.

  7. High-temperature/high-pressure x-ray diffraction: Recent developments

    SciTech Connect (OSTI)

    Schiferl, D.; Johnson, S.W.; Zinn, A.S.

    1989-01-01T23:59:59.000Z

    We have developed two Merrill-Bassett diamond-anvil cells for specialized high-temperature uses. The first is constructed largely of rhenium to provide uniform, constant P and T on the order of 20 GPa at 1200 K for extended periods. The second is for single-crystal x-ray diffraction, but can be heated to 630 K at 20 GPa to grow single-crystal samples which cannot be produced at room temperature. With this cell, the crystal structure of /var epsilon/-O/sub 2/ was shown to be monoclinic with a = 3.649 A, b = 5.493 A, c = 7.701 A, and /Beta/ = 116.11/degree/ at 19.7 GPa. 15 refs.

  8. Heat Transfer and Pressure Drop Measurement for Square Channels with V-shape Ribs at High Reynolds Numbers

    E-Print Network [OSTI]

    Alkhamis, Nawaf Yahya

    2010-10-12T23:59:59.000Z

    HEAT TRANSFER AND PRESSURE DROP MEASUREMENT FOR SQUARE CHANNELS WITH V-SHAPE RIBS AT HIGH REYNOLDS NUMBERS A Thesis by NAWAF YAHYA ALKHAMIS Submitted to the Office of Graduate Studies of Texas A&M University in partial... fulfillment of the requirements for the degree of MASTER OF SCIENCE August 2009 Major Subject: Mechanical Engineering HEAT TRANSFER AND PRESSURE DROP MEASUREMENT FOR SQUARE CHANNELS WITH V-SHAPE RIBS AT HIGH REYNOLDS NUMBERS A Thesis...

  9. Overview of chemical vapor infiltration

    SciTech Connect (OSTI)

    Besmann, T.M.; Stinton, D.P.; Lowden, R.A.

    1993-06-01T23:59:59.000Z

    Chemical vapor infiltration (CVI) is developing into a commercially important method for the fabrication of continuous filament ceramic composites. Current efforts are focused on the development of an improved understanding of the various processes in CVI and its modeling. New approaches to CVI are being explored, including pressure pulse infiltration and microwave heating. Material development is also proceeding with emphasis on improving the oxidation resistance of the interfacial layer between the fiber and matrix. This paper briefly reviews these subjects, indicating the current state of the science and technology.

  10. Development of a Water Based, Critical Flow, Non-Vapor Compression cooling Cycle

    SciTech Connect (OSTI)

    Hosni, Mohammad H.

    2014-03-30T23:59:59.000Z

    Expansion of a high-pressure liquid refrigerant through the use of a thermostatic expansion valve or other device is commonplace in vapor-compression cycles to regulate the quality and flow rate of the refrigerant entering the evaporator. In vapor-compression systems, as the condensed refrigerant undergoes this expansion, its pressure and temperature drop, and part of the liquid evaporates. We (researchers at Kansas State University) are developing a cooling cycle that instead pumps a high-pressure refrigerant through a supersonic converging-diverging nozzle. As the liquid refrigerant passes through the nozzle, its velocity reaches supersonic (or critical-flow) conditions, substantially decreasing the refrigerant’s pressure. This sharp pressure change vaporizes some of the refrigerant and absorbs heat from the surrounding conditions during this phase change. Due to the design of the nozzle, a shockwave trips the supersonic two-phase refrigerant back to the starting conditions, condensing the remaining vapor. The critical-flow refrigeration cycle would provide space cooling, similar to a chiller, by running a secondary fluid such as water or glycol over one or more nozzles. Rather than utilizing a compressor to raise the pressure of the refrigerant, as in a vapor-cycle system, the critical-flow cycle utilizes a high-pressure pump to drive refrigerant liquid through the cooling cycle. Additionally, the design of the nozzle can be tailored for a given refrigerant, such that environmentally benign substances can act as the working fluid. This refrigeration cycle is still in early-stage development with prototype development several years away. The complex multi-phase flow at supersonic conditions presents numerous challenges to fully understanding and modeling the cycle. With the support of DOE and venture-capital investors, initial research was conducted at PAX Streamline, and later, at Caitin. We (researchers at Kansas State University) have continued development of the cycle and have gained an in-depth understanding of the governing fundamental knowledge, based on the laws of physics and thermodynamics and verified with our testing results. Through this research, we are identifying optimal working fluid and operating conditions to eventually demonstrate the core technology for space cooling or other applications.

  11. High pressure melt ejection and direct containment heating in ice condenser containments

    SciTech Connect (OSTI)

    Pilch, M.; Tarbell, W.W.; Carroll, D.E.; Tills, J.L.

    1986-01-01T23:59:59.000Z

    A response of a typical ice condenser containment to a high pressure melt dispersal accident has been studied. While ice beds may be effective in reducing the potential loading caused by direct heating of the containment atmosphere, analyses suggest two other modes of containment failure that have not been previously identified. Calculations with the CONTAIN code indicate that ejected core debris may interact with steam from the primary system, generating sufficient hydrogen to threaten containment integrity. Further, if the debris ejected into the cavity promptly fails the seal table, the dispersed material could enter the in-core instrument room and attack the containment liner. The timing of the failure of the seal table is highly dependent on the characteristics of the debris-to-steel energy transfer.

  12. REMOVAL OF H2S AND SO2 BY CaCO3-BASED SORBENTS AT HIGH PRESSURES

    SciTech Connect (OSTI)

    Prof. Stratis V. Sotirchos

    2000-09-01T23:59:59.000Z

    The mechanism of the removal of SO{sub 2} and H{sub 2}S by CaCO{sub 3}-based sorbents in pressurized fluidized-bed coal combustors (PFBC) and high pressure gasifiers was investigated in this project. Reactivity evolution experiments were carried out in thermogravimetric apparatuses both under simulated high pressure conditions and at high pressures. Experiments at high pressure were conducted in a high pressure thermogravimetric arrangement that was set up and developed under this project. Two calcitic solids of high calcium carbonate content (over 97%) were employed in the experiments: a fine-grained distributed by Greer Limestone Co. (Greer Limestone) and a solid supplied in the form of large calcitic crystals (Iceland Spar). The decision to work with these solids was mainly based on the fact that they have been employed in several past studies of sulfation, sulfidation, and calcination in our laboratory, and therefore, a large volume of data on their performance under different conditions was available for comparison purposes. In addition to the experimental studies, work was also done on the development of rigorous mathematical models for the description of the occurrence of simultaneous processes (e.g., calcination and sulfation and carbonation and sulfation) in the interior of porous solids and for the simulation of the evolution of the pore structure of porous solids that undergo chemical transformation in their interior.

  13. LNG fire and vapor control system technologies

    SciTech Connect (OSTI)

    Konzek, G.J.; Yasutake, K.M.; Franklin, A.L.

    1982-06-01T23:59:59.000Z

    This report provides a review of fire and vapor control practices used in the liquefied natural gas (LNG) industry. Specific objectives of this effort were to summarize the state-of-the-art of LNG fire and vapor control; define representative LNG facilities and their associated fire and vapor control systems; and develop an approach for a quantitative effectiveness evaluation of LNG fire and vapor control systems. In this report a brief summary of LNG physical properties is given. This is followed by a discussion of basic fire and vapor control design philosophy and detailed reviews of fire and vapor control practices. The operating characteristics and typical applications and application limitations of leak detectors, fire detectors, dikes, coatings, closed circuit television, communication systems, dry chemicals, water, high expansion foam, carbon dioxide and halogenated hydrocarbons are described. Summary descriptions of a representative LNG peakshaving facility and import terminal are included in this report together with typical fire and vapor control systems and their locations in these types of facilities. This state-of-the-art review identifies large differences in the application of fire and vapor control systems throughout the LNG industry.

  14. Evolution of Nickel-Manganese-Silicon Dominated Phases in Highly Irradiated Reactor Pressure Vessel Steels

    SciTech Connect (OSTI)

    Peter B Wells; Yuan Wu; Tim Milot; G. Robert Odette; Takuya Yamamoto; Brandon Miller; James Cole

    2014-11-01T23:59:59.000Z

    Formation of a high density of Ni-Mn-Si nm-scale precipitates in irradiated reactor pressure vessel steels, both with and without Cu, could lead to severe embrittlement. Models long ago predicted that these precipitates, which are not treated in current embrittlement regulations, would emerge only at high fluence. However, the mechanisms and variables that control Ni-Mn- Si precipitate formation, and their detailed characteristics, have not been well understood. High flux irradiations of six steels with systematic variations in Cu and Ni were carried out at ˜ 295±5°C to high and very high neutron fluences of ˜ 1.3x1020 and 1.1x1021 n/cm2. Atom probe tomography (APT) shows that significant mole fractions of these precipitates form in the Cu bearing steels at ˜ 1.3x1020 n/cm2, while they are only beginning to develop in Cu-free steels. However, large mole fractions, far in excess of those found in previous studies, are observed at 1.1x1021 n/cm2 at all Cu levels. The precipitates diffract, and in one case are compositionally and structurally consistent with the Mn6Ni16Si7 G-phase. At the highest fluence, the large precipitate mole fractions primarily depend on the steel Ni content, rather than Cu, and lead to enormous strength increases up to about 700 MPa. The implications of these results to light water reactor life extension are discussed briefly.

  15. Vapor spill monitoring method

    DOE Patents [OSTI]

    Bianchini, Gregory M. (Livermore, CA); McRae, Thomas G. (Livermore, CA)

    1985-01-01T23:59:59.000Z

    Method for continuous sampling of liquified natural gas effluent from a spill pipe, vaporizing the cold liquified natural gas, and feeding the vaporized gas into an infrared detector to measure the gas composition. The apparatus utilizes a probe having an inner channel for receiving samples of liquified natural gas and a surrounding water jacket through which warm water is flowed to flash vaporize the liquified natural gas.

  16. Engineering development of a lightweight high-pressure scarifier for tank waste retrieval

    SciTech Connect (OSTI)

    Hatchell, B.K.

    1997-09-01T23:59:59.000Z

    The Retrieval Process Development and Enhancements Program (RPD&E) is sponsored by the U.S. Department of Energy Tanks Focus Area to investigate existing and emerging retrieval processes suitable for the retrieval of high-level radioactive waste inside underground storage tanks. This program, represented by industry, national laboratories, and academia, seeks to provide a technical and cost basis to support site-remediation decisions. Part of this program has involved the development of a high-pressure waterjet dislodging system and pneumatic conveyance integrated as a scarifier. Industry has used high-pressure waterjet technology for many years to mine, cut, clean, and scarify materials with a broad range of properties. The scarifier was developed as an alternate means of retrieving waste inside Hanford single-shell tanks, particularly hard, stubborn waste. Testing of the scarifier has verified its ability to retrieve a wide range of tank waste ranging from extremely hard waste that is resistant to other dislodging means to soft sludge and even supernatant fluid. Since the scarifier expends water at a low rate and recovers most of the water as it is used, the scarifier is well suited for retrieval of tanks that leak and cannot be safely sluiced or applications where significant waste dilution is not acceptable. Although the original scarifier was effective, it became evident that a lighter, more compact version that would be compatible with light weight deployment systems under development, such as the Light Duty Utility Arm, was needed. At the end of FY 95, the Light Weight Scarifier (LWS) was designed to incorporate the features of the original scarifier in a smaller, lighter end effector. During FY 96, the detailed design of the LWS was completed and two prototypes were fabricated.

  17. Diamond-anvil high-pressure cell with improved X-ray collimation system

    DOE Patents [OSTI]

    Schiferl, David (Los Alamos, NM); Olinger, Barton W. (Santa Fe, NM); Livingston, Robert W. (Los Alamos, NM)

    1986-01-01T23:59:59.000Z

    An adjustable X-ray collimation system for a diamond-anvil high-pressure cell of the type including a cooperable piston and cylinder and a pair of opposing diamonds located between the head of the piston and the head of the cylinder. The X-ray collimation system includes a tubular insert which contains an X-ray collimator. The insert is engageable in the bore of the piston. The collimator is mounted within the insert by means of an elastomeric O-ring at the end closest the opposed diamonds, and by means of a set of adjustable set screws at the opposite end. By adjustment of the set screws the collimator can be pivoted about the O-ring and brought into alignment with the opposed diamonds and the sample contained therein. In the preferred embodiment there is further provided a set of plugs which are insertable in the bore of the collimator. The plugs have bores of different diameters. By successively inserting plugs of progressively smaller bore diameters and adjusting the alignment of the collimator with each plug, the collimator can be quickly brought into accurate alignment with the diamonds. The collimation system allows alignment of the collimator either before or after the cell has been loaded and pressurized.

  18. Diamond-anvil high-pressure cell with improved x-ray collimation system

    DOE Patents [OSTI]

    Schiferl, D.; Olinger, B.W.; Livingston, R.W.

    1984-03-30T23:59:59.000Z

    An adjustable x-ray collimation system for a diamond-anvil high-pressure cell of the type including a cooperable piston and cylinder and a pair of opposing diamonds located between the head of the piston and the head of the cylinder. The x-ray collimation system includes a tubular insert which contains an x-ray collimator. The insert is engageable in the bore of the piston. The collimator is mounted within the insert by means of an elastomeric o-ring at the end closest the opposed diamonds, and by means of a set of adjustable set screws at the opposite end. By adjustment of the set screws the collimator can be pivoted about the o-ring and brought into alignment with the opposed diamonds and the sample contained therein. In the preferred embodiment there is further provided a set of plugs which are insertable in the bore of the collimator. The plugs have bores of different diameters. By successively inserting plugs of progressively smaller bore diameters and adjusting the alignment of the collimator with each plug, the collimator can be quickly brought into accurate alignment with the diamonds. The collimation system allows alignment of the collimator either before or after the cell has been loaded and pressurized.

  19. Wear Mechanism of Chemical Vapor Deposition (CVD) Carbide Insert in Orthogonal Cutting Ti-6Al-4V ELI at High Cutting Speed

    SciTech Connect (OSTI)

    Gusri, A. I.; Che Hassan, C. H.; Jaharah, A. G. [Mechanical and Material Engineering Department, Universiti Kebangsaan Malaysia, Bangi 43600 (Malaysia)

    2011-01-17T23:59:59.000Z

    The performance of Chemical Vapor Deposition (CVD) carbide insert with ISO designation of CCMT 12 04 04 LF, when turning titanium alloys was investigated. There were four layers of coating materials for this insert i.e.TiN-Al2O3-TiCN-TiN. The insert performance was evaluated based on the insert's edge resistant towards the machining parameters used at high cutting speed range of machining Ti-6Al-4V ELI. Detailed study on the wear mechanism at the cutting edge of CVD carbide tools was carried out at cutting speed of 55-95 m/min, feed rate of 0.15-0.35 mm/rev and depth of cut of 0.10-0.20 mm. Wear mechanisms such as abrasive and adhesive were observed on the flank face. Crater wear due to diffusion was also observed on the rake race. The abrasive wear occurred more at nose radius and the fracture on tool were found at the feed rate of 0.35 mm/rev and the depth of cut of 0.20 mm. The adhesion wear takes place after the removal of the coating or coating delaminating. Therefore, adhesion or welding of titanium alloy onto the flank and rake faces demonstrates a strong bond at the workpiece-tool interface.

  20. Mechanical behaviors and phase transition of Ho{sub 2}O{sub 3} nanocrystals under high pressure

    SciTech Connect (OSTI)

    Yan, Xiaozhi [Institute of Atomic and Molecular Physics, Sichuan University, Chengdu 610065 (China); Center for High Pressure Science and Technology Advanced Research (HPSTAR), 1690 Cailun Rd., Pudong, Shanghai 201203 (China); Ren, Xiangting [Institute of Atomic and Molecular Physics, Sichuan University, Chengdu 610065 (China); He, Duanwei, E-mail: duanweihe@scu.edu.cn, E-mail: yangwg@hpstar.ac.cn [Institute of Atomic and Molecular Physics, Sichuan University, Chengdu 610065 (China); Institute of Fluid Physics and National Key Laboratory of Shockwave and Detonation Physic, China Academy of Engineering Physics, Mianyang 621900 (China); Chen, Bin [Center for High Pressure Science and Technology Advanced Research (HPSTAR), 1690 Cailun Rd., Pudong, Shanghai 201203 (China); Yang, Wenge, E-mail: duanweihe@scu.edu.cn, E-mail: yangwg@hpstar.ac.cn [Center for High Pressure Science and Technology Advanced Research (HPSTAR), 1690 Cailun Rd., Pudong, Shanghai 201203 (China); High Pressure Synergetic Consortium (HPSynC), Geophysical Laboratory, Carnegie Institution of Washington, 9700 S Cass Avenue, Argonne, Illinois 60439 (United States)

    2014-07-21T23:59:59.000Z

    Mechanical properties and phase transition often show quite large crystal size dependent behavior, especially at nanoscale under high pressure. Here, we have investigated Ho{sub 2}O{sub 3} nanocrystals with in-situ x-ray diffraction and Raman spectroscopy under high pressure up to 33.5?GPa. When compared to the structural transition routine cubic -> monoclinic -> hexagonal phase in bulk Ho{sub 2}O{sub 3} under high pressure, the nano-sized Ho{sub 2}O{sub 3} shows a much higher onset transition pressure from cubic to monoclinic structure and followed by a pressure-induced-amorphization under compression. The detailed analysis on the Q (Q?=?2?/d) dependent bulk moduli reveals the nanosized Ho{sub 2}O{sub 3} particles consist of a clear higher compressible shell and a less compressible core. Insight into these phenomena shed lights on micro-mechanism studies of the mechanical behavior and phase evolution for nanomaterials under high pressure, in general.

  1. The deterioration in heat transfer to fluids at supercritical pressure and high heat fluxes

    E-Print Network [OSTI]

    Shiralkar, B. S.

    1968-01-01T23:59:59.000Z

    At slightly supercritical pressure and in the neighborhood of the pseudo-critical temperature (defined as the temperature corresponding to the peak in specific heat at the operating pressure), the heat transfer coefficient ...

  2. Energy savings with solid-state ballasted high-pressure sodium lamps

    SciTech Connect (OSTI)

    Verderber, R.R.; Morse, O.

    1981-04-01T23:59:59.000Z

    The performance of three types of solid-state ballasts used to operate high-pressure sodium lamps is discussed. Each type of solid-state ballast has been designed to operate an HPS lamp of a different wattage (150, 200, and 400 watts). The performance of these ballasts compared to standard core-coil ballasts operating the same HPS lamps shows that system efficiency improves as much as 17%. The solid-state ballasted HPS system also demonstrates excellent regulation with respect to input voltage and output power. These new ballasts can dim the HPS lamps and reduce flicker from more than 60% to less than 3%. Refitting street lighting with these new HPS systims provides an attractive return on initial capital investment.

  3. Dynamics of multiple double layers in high pressure glow discharge in a simple torus

    SciTech Connect (OSTI)

    Kumar Paul, Manash, E-mail: manashkr@gmail.com [Department of Physics, National Institute of Technology Agartala, Tripura–799 046 (India); Sharma, P. K.; Thakur, A.; Kulkarni, S. V.; Bora, D. [Institute for Plasma Research, Bhat, Gandhinagar, Gujarat–382 428 (India)

    2014-06-15T23:59:59.000Z

    Parametric characterization of multiple double layers is done during high pressure glow discharge in a toroidal vessel of small aspect ratio. Although glow discharge (without magnetic field) is known to be independent of device geometry, but the toroidal boundary conditions are conducive to plasma growth and eventually the plasma occupy the toroidal volume partially. At higher anode potential, the visibly glowing spots on the body of spatially extended anode transform into multiple intensely luminous spherical plasma blob structures attached to the tip of the positive electrode. Dynamics of multiple double layers are observed in argon glow discharge plasma in presence of toroidal magnetic field. The radial profiles of plasma parameters measured at various toroidal locations show signatures of double layer formation in our system. Parametric dependence of double layer dynamics in presence of toroidal magnetic field is presented here.

  4. Experimental observation of standing wave effect in low-pressure very-high-frequency capacitive discharges

    SciTech Connect (OSTI)

    Liu, Yong-Xin; Gao, Fei; Liu, Jia; Wang, You-Nian, E-mail: ynwang@dlut.edu.cn [Key Laboratory of Materials Modification by Laser, Ion, and Electron Beams (Ministry of Education), School of Physics and Optoelectronic Technology, Dalian University of Technology, Dalian 116024 (China)

    2014-07-28T23:59:59.000Z

    Radial uniformity measurements of plasma density were carried out by using a floating double probe in a cylindrical (21?cm in electrode diameter) capacitive discharge reactor driven over a wide range of frequencies (27–220 MHz). At low rf power, a multiple-node structure of standing wave effect was observed at 130?MHz. The secondary density peak caused by the standing wave effect became pronounced and shifts toward the axis as the driving frequency further to increase, indicative of a much more shortened standing-wave wavelength. With increasing rf power, the secondary density peak shift toward the radial edge, namely, the standing-wave wavelength was increased, in good qualitative agreement with the previous theory and simulation results. At higher pressures and high frequencies, the rf power was primarily deposited at the periphery of the electrode, due to the fact that the waves were strongly damped as they propagated from the discharge edge into the center.

  5. Beam Profile Measurement in MTA Beam Line for High Pressure RF Cavity Beam Test

    SciTech Connect (OSTI)

    Jana, M.R.; Bross, A.; Chung, M.; Greer, S.; Johnstone, C.; Kobilarcik, T.; Koizumi, G.; Leonova, M.; Moretti, A.; Popovic, M.; Schwartz, T.; /Fermilab /IIT, Chicago /PDT, Torino

    2012-05-15T23:59:59.000Z

    Recent High Pressure RF (HPRF) cavity experiment at MuCool Test Area (MTA) has used 400 MeV Linac proton beam to study the beam loading effect. When the energetic proton beam passes through the cavity, it ionizes the inside gas and produces the electrons. These electrons consume RF power inside the cavity. Number of electrons produced per cm inside the cavity (at 950 psi Hydrogen gas) per incident proton is {approx} 1200. The measurement of beam position and profile are necessary. MTA is flammable gas (Hydrogen) hazard zone so we have developed a passive beam diagnostic instrument using Chromox-6 scintillation screen and CCD camera. This paper presents quantitative information about beam position and beam profile. Neutral density filter was used to avoid saturation of CCD camera. Image data is filtered and fitted with Gaussian function to compute the beam size. The beam profile obtained from scintillation screen shall be compared with multi-wire beam profile.

  6. Fiber-optic, anti-cycling, high pressure sodium street light control. Final technical progress report

    SciTech Connect (OSTI)

    NONE

    1995-05-01T23:59:59.000Z

    This is the Final Technical Progress Report on a project to develop and market a Fiber-Optic Anti-Cycling High Pressure Sodium Street Light Control. The field test units are now being made with a single vertical PC board design and contains a computer-on-a-chip or PROM IC to take the place of the majority of the components previously contained on the upper logic board. This will reduce the final costs of the unit when it is in production and increase the control`s flexibility. The authors have finished the soft tooling and have made the 400 plastic cases for the field test units. The new configuration of the cases entails a simplified design of the control shell which will have the lenses cast in place. The shell and base plastics are now finished and in final assembly awaiting the completion of the PC boards.

  7. Rapid Migration of Radionuclides Leaked from High-Level Water Tanks; A Study of Salinity Gradients, Wetted Path Geometry and Water Vapor Transport

    SciTech Connect (OSTI)

    Anderson l. Ward; Glendon W. Gee; John S. Selker; Clay Cooper

    2002-04-24T23:59:59.000Z

    The basis of this study was the hypothesis that the physical and chemical properties of hypersaline tank waste could lead to wetting from instability and fingered flow following a tank leak. Thus, the goal of this project was to develop an understanding of the impacts of the properties of hypersaline fluids on transport through the unsaturated zone beneath Hanford's Tank Farms. There were three specific objectives (i) to develop an improved conceptualization of hypersaline fluid transport in laboratory (ii) to identify the degree to which field conditions mimic the flow processes observed in the laboratory and (iii) to provide a validation data set to establish the degree to which the conceptual models, embodied in a numerical simulator, could explain the observed field behavior. As hypothesized, high ionic strength solutions entering homogeneous pre-wetted porous media formed unstable wetting fronts atypical of low ionic strength infiltration. In the field, this mechanism could for ce flow in vertical flow paths, 5-15 cm in width, bypassing much of the media and leading to waste penetration to greater depths than would be predicted by current conceptual models. Preferential flow may lead to highly accelerated transport through large homogeneous units, and must be included in any conservative analysis of tank waste losses through coarse-textured units. However, numerical description of fingered flow using current techniques has been unreliable, thereby precluding tank-scale 3-D simulation of these processes. A new approach based on nonzero, hysteretic contract angles and fluid-dependent liquid entry has been developed for the continuum scale modeling of fingered flow. This approach has been coupled with and adaptive-grid finite-difference solver to permit the prediction of finger formation and persistence form sub centimeter scales to the filed scale using both scalar and vector processors. Although laboratory experiments demonstrated that elevated surface tens ion of imbibing solutions can enhance vertical fingered flow, this phenomenon was not observed in the field. Field tests showed that the fingered flow behavior was overwhelmed by the variability in texture resulting from differences in the depositional environment. Field plumes were characterized by lateral spreading with an average width to depth aspect ratio of 4. For both vertical fingers and lateral flow, the high ionic strength contributed to the vapor phase dilution of the waste, which increased waste volume and pushed the wetting from well beyond what would have occurred if the volume of material had remained unchanged from that initially released into the system. It was also observed that following significant vapor-phase dilution of this waste simulants that streams of colloids were ejected from the sediment surfaces. It was shown that due to the high-sodium content of the tank wastes the colloids were deflocculated below a critical salt concentration in Hanford sediments. Th e released colloids, which at the site would be expected to carry the bulk of the sorbed heavy metals and radioisotopes, were mobile though coarse Hanford sediments, but clogged finer layers. The developments resulting from this study are already being applied at Hanford in the nonisothermal prediction of the hypersaline, high pH waste migration in tank farms and in the development of inverse methods for history matching under DOE's Groundwater/Vadose Zone Integration Project at Hanford.

  8. Rapid Migration of Radionuclides Leaked from High-Level Water Tanks: A Study of Salinity Gradients, Wetted Path Geometry and Water Vapor Transport

    SciTech Connect (OSTI)

    Anderson L. Ward; Glendon W. Gee; John S. Selker; Caly Cooper

    2002-04-24T23:59:59.000Z

    The basis of this study was the hypothesis that the physical and chemical properties of hypersaline tank waste could lead to wetting from instability and fingered flow following a tank leak. Thus, the goal of this project was to develop an understanding of the impacts of the properties of hypersaline fluids on transport through the unsaturated zone beneath Hanford's Tank Farms. There were three specific objectives (i) to develop an improved conceptualization of hypersaline fluid transport in laboratory (ii) to identify the degree to which field conditions mimic the flow processes observed in the laboratory and (iii) to provide a validation data set to establish the degree to which the conceptual models, embodied in a numerical simulator, could explain the observed field behavior. As hypothesized, high ionic strength solutions entering homogeneous pre-wetted porous media formed unstable wetting fronts a typical of low ionic strength infiltration. In the field, this mechanism could force flow in vertical flow paths, 5-15 cm in width, bypassing much of the media and leading to waste penetration to greater depths than would be predicted by current conceptual models. Preferential flow may lead to highly accelerated transport through large homogeneous units, and must be included in any conservative analysis of tank waste losses through coarse-textured units. However, numerical description of fingered flow using current techniques has been unreliable, thereby precluding tank-scale 3-D simulation of these processes. A new approach based on nonzero, hysteretic contact angles and fluid-dependent liquid entry has been developed for the continuum scale modeling of fingered flow. This approach has been coupled with and adaptive-grid finite-difference solver to permit the prediction of finger formation and persistence form sub centimeter scales to the filed scale using both scalar and vector processors. Although laboratory experiments demonstrated that elevated surface tension of imbibing solutions can enhance vertical fingered flow, this phenomenon was not observed in the field. Field tests of showed that the fingered flow behavior was overwhelmed by the variability in texture resulting from differences in the depositional environment. Field plumes were characterized by lateral spreading with an average width to depth aspect ratio of 4. For both vertical fingers and lateral flow, the high ionic strength contributed to the vapor phase dilution of the waste, which increased waste volume and pushed the wetting from well beyond what would have occurred if the volume of material had remained unchanged from that initially released into the system. It was also observed that following significant vapor-phase dilution of the waste simulants that streams of colloids were ejected from the sediment surfaces. It was shown that due to the high-sodium content of the tank wastes the colloids were deflocculated below a critical salt concentration in Hanford sediment s. The released colloids, which at the site would be expected to carry the bulk of the sorbed heavy metals and radioisotopes, were mobile though coarse Hanford sediments, but clogged finer layers. The developments resulting from this study are already being applied at Hanford in the nonisothermal prediction of the hypersaline, high pH waste migration in tank farms and in the development of inverse methods for history matching under DOE's Groundwater/Vadose Zone Integration Project at Hanford.

  9. Adsorption of water vapor on reservoir rocks

    SciTech Connect (OSTI)

    Not Available

    1993-07-01T23:59:59.000Z

    Progress is reported on: adsorption of water vapor on reservoir rocks; theoretical investigation of adsorption; estimation of adsorption parameters from transient experiments; transient adsorption experiment -- salinity and noncondensible gas effects; the physics of injection of water into, transport and storage of fluids within, and production of vapor from geothermal reservoirs; injection optimization at the Geysers Geothermal Field; a model to test multiwell data interpretation for heterogeneous reservoirs; earth tide effects on downhole pressure measurements; and a finite-difference model for free surface gravity drainage well test analysis.

  10. Autoignition of toluene reference fuels at high pressures modeled with detailed chemical kinetics

    SciTech Connect (OSTI)

    Andrae, J.C.G. [Department of Chemical Engineering and Technology, Royal Institute of Technology, SE-100 44 Stockholm (Sweden); Shell Global Solutions, P.O. Box 1, Chester CH1 3SH (United Kingdom); Bjoernbom, P. [Department of Chemical Engineering and Technology, Royal Institute of Technology, SE-100 44 Stockholm (Sweden); Cracknell, R.F.; Kalghatgi, G.T. [Shell Global Solutions, P.O. Box 1, Chester CH1 3SH (United Kingdom)

    2007-04-15T23:59:59.000Z

    A detailed chemical kinetic model for the autoignition of toluene reference fuels (TRF) is presented. The toluene submechanism added to the Lawrence Livermore Primary Reference Fuel (PRF) mechanism was developed using recent shock tube autoignition delay time data under conditions relevant to HCCI combustion. For two-component fuels the model was validated against recent high-pressure shock tube autoignition delay time data for a mixture consisting of 35% n-heptane and 65% toluene by liquid volume. Important features of the autoignition of the mixture proved to be cross-acceleration effects, where hydroperoxy radicals produced during n-heptane oxidation dramatically increased the oxidation rate of toluene compared to the case when toluene alone was oxidized. Rate constants for the reaction of benzyl and hydroperoxyl radicals previously used in the modeling of the oxidation of toluene alone were untenably high for modeling of the mixture. To model both systems it was found necessary to use a lower rate and introduce an additional branching route in the reaction between benzyl radicals and O{sub 2}. Good agreement between experiments and predictions was found when the model was validated against shock tube autoignition delay data for gasoline surrogate fuels consisting of mixtures of 63-69% isooctane, 14-20% toluene, and 17% n-heptane by liquid volume. Cross reactions such as hydrogen abstractions between toluene and alkyl and alkylperoxy radicals and between the PRF were introduced for completion of chemical description. They were only of small importance for modeling autoignition delays from shock tube experiments, even at low temperatures. A single-zone engine model was used to evaluate how well the validated mechanism could capture autoignition behavior of toluene reference fuels in a homogeneous charge compression ignition (HCCI) engine. The model could qualitatively predict the experiments, except in the case with boosted intake pressure, where the initial temperature had to be increased significantly in order to predict the point of autoignition. (author)

  11. High pressure elastic properties of minerals from ab initio simulations: The case of pyrope, grossular and andradite silicate garnets

    SciTech Connect (OSTI)

    Erba, A., E-mail: alessandro.erba@unito.it; Mahmoud, A.; Dovesi, R. [Dipartimento di Chimica and Centre of Excellence NIS (Nanostructured Interfaces and Surfaces), Università di Torino, via Giuria 5, IT-10125 Torino (Italy)] [Dipartimento di Chimica and Centre of Excellence NIS (Nanostructured Interfaces and Surfaces), Università di Torino, via Giuria 5, IT-10125 Torino (Italy); Belmonte, D. [DISTAV, Università di Genova, Corso Europa 26, 16132 Genoa (Italy)] [DISTAV, Università di Genova, Corso Europa 26, 16132 Genoa (Italy)

    2014-03-28T23:59:59.000Z

    A computational strategy is devised for the accurate ab initio simulation of elastic properties of crystalline materials under pressure. The proposed scheme, based on the evaluation of the analytical stress tensor and on the automated computation of pressure-dependent elastic stiffness constants, is implemented in the CRYSTAL solid state quantum-chemical program. Elastic constants and related properties (bulk, shear and Young moduli, directional seismic wave velocities, elastic anisotropy index, Poisson's ratio, etc.) can be computed for crystals of any space group of symmetry. We apply such a technique to the study of high-pressure elastic properties of three silicate garnet end-members (namely, pyrope, grossular, and andradite) which are of great geophysical interest, being among the most important rock-forming minerals. The reliability of this theoretical approach is proved by comparing with available experimental measurements. The description of high-pressure properties provided by several equations of state is also critically discussed.

  12. The effect of high-pressure injection of gas on the reservoir volume factor of a crude oil

    E-Print Network [OSTI]

    Honeycutt, Baxter Bewitt

    1957-01-01T23:59:59.000Z

    . The gas was taken from the casing annulus at 180 psig pressure after the well had flowed for about 3 hours. An analysis of the gas is given in Table 4. Gravity of the oil was 37. 3 API at 60oF. Reservoir pressure in the Charlotte Field... are different at different locations in the reservoir. In the high-pressure zone about the injection well ? a substantial amount of the oil dissolves in the gas, leaving a low residual oil saturation consisting of the heaviest fraction of the oil...

  13. High-pressure X-ray diffraction and X-ray emission studies on iron-bearing silicate perovskite under high pressures

    SciTech Connect (OSTI)

    Lin, Jung-Fu; Speciale, Sergio; Prakapenka, Vitali B.; Dera, Przemek; Lavina, Babara; Watson, Heather C. (NIU); (UC); (Texas); (GFZ)

    2010-06-22T23:59:59.000Z

    Iron-bearing silicate perovskite is believed to be the most abundant mineral of the Earth's lower mantle. Recent studies have shown that Fe{sup 2+} exists predominantly in the intermediate-spin state with a total spin number of 1 in silicate perovskite in the lower part of the lower mantle. Here we have measured the spin states of iron and the pressure-volume relation in silicate perovskite [(Mg{sub 0.6},Fe{sub 0.4})SiO{sub 3}] at pressure conditions relevant to the lowermost mantle using in situ X-ray emission and X-ray diffraction in a diamond cell. Our results showed that the intermediate-spin Fe{sup 2+} is stable in the silicate perovskite up to {approx} 125 GPa but starts to transition to the low-spin state at approximately 135 GPa. Concurrent X-ray diffraction measurements showed a decrease of approximately 1% in the unit cell volume in the silicate perovskite [(Mg{sub 0.6},Fe{sub 0.4})SiO{sub 3}], which is attributed to the intermediate-spin to the low-spin transition. The transition pressure coincides with the pressure conditions of the lowermost mantle, raising the possibility of the existence of the silicate perovskite phase with the low-spin Fe{sup 2+} across the transition from the post-perovskite to the perovskite phases in the bottom of the D{double_prime} layer.

  14. Metal vapor laser including hot electrodes and integral wick

    DOE Patents [OSTI]

    Ault, Earl R. (Livermore, CA); Alger, Terry W. (Tracy, CA)

    1995-01-01T23:59:59.000Z

    A metal vapor laser, specifically one utilizing copper vapor, is disclosed herein. This laser utilizes a plasma tube assembly including a thermally insulated plasma tube containing a specific metal, e.g., copper, and a buffer gas therein. The laser also utilizes means including hot electrodes located at opposite ends of the plasma tube for electrically exciting the metal vapor and heating its interior to a sufficiently high temperature to cause the metal contained therein to vaporize and for subjecting the vapor to an electrical discharge excitation in order to lase. The laser also utilizes external wicking arrangements, that is, wicking arrangements located outside the plasma tube.

  15. Metal vapor laser including hot electrodes and integral wick

    DOE Patents [OSTI]

    Ault, E.R.; Alger, T.W.

    1995-03-07T23:59:59.000Z

    A metal vapor laser, specifically one utilizing copper vapor, is disclosed herein. This laser utilizes a plasma tube assembly including a thermally insulated plasma tube containing a specific metal, e.g., copper, and a buffer gas therein. The laser also utilizes means including hot electrodes located at opposite ends of the plasma tube for electrically exciting the metal vapor and heating its interior to a sufficiently high temperature to cause the metal contained therein to vaporize and for subjecting the vapor to an electrical discharge excitation in order to lase. The laser also utilizes external wicking arrangements, that is, wicking arrangements located outside the plasma tube. 5 figs.

  16. Advanced Production Surface Preparation Technology Development for Ultra-High Pressure Diesel Injection

    SciTech Connect (OSTI)

    Grant, Marion B.

    2012-04-30T23:59:59.000Z

    In 2007, An Ultra High Injection Pressure (UHIP) fueling method has been demonstrated by Caterpillar Fuel Systems - Product Development, demonstrating ability to deliver U.S. Environment Protection Agency (EPA) Tier 4 Final diesel engine emission performance with greatly reduced emissions handling components on the engine, such as without NOx reduction after-treatment and with only a through-flow 50% effective diesel particulate trap (DPT). They have shown this capability using multiple multi-cylinder engine tests of an Ultra High Pressure Common Rail (UHPCR) fuel system with higher than traditional levels of CEGR and an advanced injector nozzle design. The system delivered better atomization of the fuel, for more complete burn, to greatly reduce diesel particulates, while CEGR or high efficiency NOx reduction after-treatment handles the NOx. With the reduced back pressure of a traditional DPT, and with the more complete fuel burn, the system reduced levels of fuel consumption by 2.4% for similar delivery of torque and horsepower over the best Tier 4 Interim levels of fuel consumption in the diesel power industry. The challenge is to manufacture the components in high-volume production that can withstand the required higher pressure injection. Production processes must be developed to increase the toughness of the injector steel to withstand the UHIP pulsations and generate near perfect form and finish in the sub-millimeter size geometries within the injector. This project resulted in two developments in 2011. The first development was a process and a machine specification by which a high target of compressive residual stress (CRS) can be consistently imparted to key surfaces of the fuel system to increase the toughness of the steel, and a demonstration of the feasibility of further refinement of the process for use in volume production. The second development was the demonstration of the feasibility of a process for imparting near perfect, durable geometry to these same feature surfaces to withstand the pulsating UHIP diesel injection without fatigue failure, through the expected life of the fuel system's components (10,000 hours for the pump and common rail, 5000 hours for the injector). The potential to Caterpillar of this fueling approach and the overall emissions reduction system is the cost savings of the fuel, the cost savings of not requiring a full emissions module and other emissions hardware, and the enabling of the use of biodiesel fuel due to the reduced dependency on after-treatment. A proprietary production CRS generating process was developed to treat the interior of the sac-type injector nozzle tip region (particularly for the sac region). Ninety-five tips passed ultra high pulsed pressure fatigue testing with no failures assignable to treated surfaces or materials. It was determined that the CRS impartation method does not weaken the tip internal seat area. Caterpillar Fuel Systems - Product Development accepts that the CRS method initial production technical readiness level has been established. A method to gage CRS levels in production was not yet accomplished, but it is believed that monitoring process parameters call be used to guarantee quality. A precision profiling process for injector seat and sac regions has been shown to be promising but not yet fully confirmed. It was demonstrated that this precision profiling process can achieve form and geometry to well under an aggressively small micron peak-to-valley and that there are no surface flaws that approach an even tighter micron peak-to-valley tolerance. It is planned to purchase machines to further develop and move the process towards production. The system is targeted towards the high-power diesel electric power generators and high-power diesel marine power generators, with displacement from 20 liters to 80 liters and with power from 800 brake horsepower (BHP) to 3200BHP (0.6 megawatts to 2.4 megawatts). However, with market adoption, this system has the potential to meet EPA exhaust standards for all diesel engines nine liters and up, or 300B

  17. assisted chemical vapor: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    nanodiamonds (NDs) with 70-80 nm size via bead assisted sonic disintegration (BASD) of a polycrystalline chemical vapor deposition (CVD) film. The NDs display high crystalline...

  18. Efficient 3D numerical prediction of the pressure wave generated by high-speed trains entering tunnels

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Efficient 3D numerical prediction of the pressure wave generated by high-speed trains entering in a tunnel. The movement of the train is made thanks to a technique of sliding meshes and a conservative-dimensional simulation, Cartesian mesh, Sliding grid, Non-reflecting boundary conditions, High-speed trains. 1

  19. High pressure synthesis of late rare earth RFeAs(O,F) superconductors; R = Tb and Dy 

    E-Print Network [OSTI]

    Attfield, J.P.; Huxley A.D.; Sokolov D.A.; Rodgers J.A.; Penny G.B.S.; Bos J.W.G.

    2008-01-01T23:59:59.000Z

    New TbFeAs(O,F) and DyFeAs(O,F) superconductors with critical temperatures T-c = 46 and 45 K and very high critical fields, >= 100 T, have been prepared at 1100-1150 degrees C and 10-12 GPa, demonstrating that high pressure ...

  20. ACS Div of Fuel Chem Preprints 44:4, 1016-1019 (August, 1999) KINETICS OF HIGH PRESSURE CHAR OXIDATION

    E-Print Network [OSTI]

    Fletcher, Thomas H.

    ACS Div of Fuel Chem Preprints 44:4, 1016-1019 (August, 1999) KINETICS OF HIGH PRESSURE CHAR) by devolatilizing Pittsburgh #8 coal at #12;ACS Div of Fuel Chem Preprints 44:4, 1016-1019 (August, 1999) high

  1. An atmospheric pressure, fluidized bed combustion system burning high-chlorine coals in the convection section

    SciTech Connect (OSTI)

    Liu, K.; Xie, W.; Pan, W.P.; Riley, J.T.

    2000-03-01T23:59:59.000Z

    The possibility of fireside corrosion in power plant boiler components is always a major concern when the fuels include high-sulfur and high-chlorine coals (or refuse waste). Sulfur and chloride products may play important roles especially in fireside corrosion in atmospheric pressure, fluidized bed combustion (AFBC) systems, caused by the capture of sulfur and chlorine by limestone used as bed material in the combustor, and the resulting deposition of sulfur- or chlorine-rich compounds onto metallic surfaces. Results were reported from tests in a 0.1-MW{sub th} AFBC system where 1,000-h test burns were conducted using two coals with widely differing chlorine levels, and limestone was used as the sulfur sorbent. Coupons of three stainless steels (Types 304 [UNS S30400], 309 [UNS S30900], 347 [UNS S34700]) were exposed to the hot flue gases in the freeboard ({approximately} 10- cm below the location of the convection pass tubes). Deposits formed on the alloys contained high sulfur concentrations in their outer parts, as well as sodium, potassium, magnesium, and calcium. Sulfur appeared to be associated with calcium and magnesium, suggesting that the fly ash may have reacted further after being deposited on the surface of the coupon. Areas of high sulfur concentration also correlated well with areas of high chromium content of the inner layers of the scales. cross sections of samples indicated that sulfur had penetrated into the alloy and reacted to form sulfide corrosion products. There was no direct evidence to show that alkali chlorides were involved in the corrosion process. No chloride was identified in the alloy samples. There was slight oxide spallation observed on all three alloys, with the degree of spallation in the following order: Type 304 > Type 347 > Type 309.

  2. Advanced Models of LWR Pressure Vessel Embrittlement for Low Flux-HighFluence Conditions

    SciTech Connect (OSTI)

    Odette, G. Robert; Yamamoto, Takuya

    2013-06-17T23:59:59.000Z

    Neutron embrittlement of reactor pressure vessels (RPVs) is an unresolved issue for light water reactor life extension, especially since transition temperature shifts (TTS) must be predicted for high 80-year fluence levels up to approximately 1,020 n/cm{sup 2}, far beyond the current surveillance database. Unfortunately, TTS may accelerate at high fluence, and may be further amplified by the formation of late blooming phases that result in severe embrittlement even in low-copper (Cu) steels. Embrittlement by this mechanism is a potentially significant degradation phenomenon that is not predicted by current regulatory models. This project will focus on accurately predicting transition temperature shifts at high fluence using advanced physically based, empirically validated and calibrated models. A major challenge is to develop models that can adjust test reactor data to account for flux effects. Since transition temperature shifts depend on synergistic combinations of many variables, flux-effects cannot be treated in isolation. The best current models systematically and significantly under-predict transition temperature at high fluence, although predominantly for irradiations at much higher flux than actual RPV service. This project will integrate surveillance, test reactor and mechanism data with advanced models to address a number of outstanding RPV embrittlement issues. The effort will include developing new databases and preliminary models of flux effects for irradiation conditions ranging from very low (e.g., boiling water reactor) to high (e.g., accelerated test reactor). The team will also develop a database and physical models to help predict the conditions for the formation of Mn-Ni-Si late blooming phases and to guide future efforts to fully resolve this issue. Researchers will carry out other tasks on a best-effort basis, including prediction of transition temperature shift attenuation through the vessel wall, remediation of embrittlement by annealing, and fracture toughness master curve issues.

  3. High Temperature and Pressure Steam-H2 Interaction with Candidate Advanced LWR Fuel Claddings

    SciTech Connect (OSTI)

    Pint, Bruce A [ORNL

    2012-08-01T23:59:59.000Z

    This report summarizes the work completed to evaluate cladding materials that could serve as improvements to Zircaloy in terms of accident tolerance. This testing involved oxidation resistance to steam or H{sub 2}-50% steam environments at 800-1350 C at 1-20 bar for short times. A selection of conventional alloys, SiC-based ceramics and model alloys were used to explore a wide range of materials options and provide guidance for future materials development work. Typically, the SiC-based ceramic materials, alumina-forming alloys and Fe-Cr alloys with {ge}25% Cr showed the best potential for oxidation resistance at {ge}1200 C. At 1350 C, FeCrAl alloys and SiC remained oxidation resistant in steam. Conventional austenitic steels do not have sufficient oxidation resistance with only {approx}18Cr-10Ni. Higher alloyed type 310 stainless steel is protective but Ni is not a desirable alloy addition for this application and high Cr contents raise concern about {alpha}{prime} formation. Higher pressures (up to 20.7 bar) and H{sub 2} additions appeared to have a limited effect on the oxidation behavior of the most oxidation resistant alloys but higher pressures accelerated the maximum metal loss for less oxidation resistant steels and less metal loss was observed in a H{sub 2}-50%H{sub 2}O environment at 10.3 bar. As some of the results regarding low-alloyed FeCrAl and Fe-Cr alloys were unexpected, further work is needed to fundamentally understand the minimum Cr and Al alloy contents needed for protective behavior in these environments in order to assist in alloy selection and guide alloy development.

  4. High-Pressure Micellar Solutions of Symmetric and Asymmetric Styrene?Diene Diblocks in Compressible Near Critical Solvents: Micellization Pressures and Cloud Pressures Respond but Micellar Cloud Pressures Insensitive to Copolymer Molecular Weight, Concentration, and Block Ratio Changes

    SciTech Connect (OSTI)

    Winoto, Winoto [University of Wyoming, Laramie; Tan, Sugata [University of Wyoming, Laramie; Shen, Youqin [University of Wyoming, Laramie; Radosz, Maciej [University of Wyoming, Laramie; Hong, Kunlun [ORNL; Mays, Jimmy [ORNL

    2009-01-01T23:59:59.000Z

    Micellar solutions of polystyrene-block-polybutadiene and polystyrene-block-polyisoprene in propane are found to exhibit significantly lower cloud pressures than the corresponding hypothetical nonmicellar solutions. Such a cloud-pressure reduction indicates the extent to which micelle formation enhances the apparent diblock solubility in near-critical and hence compressible propane. Concentration-dependent pressure-temperature points beyond which no micelles can be formed, referred to as the micellization end points, are found to depend on the block type, size, and ratio. The cloud-pressure reduction and the micellization end point measured for styrene-diene diblocks in propane should be characteristic of all amphiphilic diblock copolymer solutions that form micelles in compressible solvents.

  5. High-pressure mechanical and sonic properties of a Devonian shale from West Virginia

    SciTech Connect (OSTI)

    Heard, H.C.; Lin, W.

    1986-01-01T23:59:59.000Z

    Static mechanical properties and sonic velocities were determined on each of four members of the Devonian shale from Columbia Gas Transmission's well 20403, Huntington, West Virginia. They were: Pressure - volume data to 4.0 GPa; Compressive strength at confining pressures up to 300 MPa, both parallel and perpendicular to bedding. Extensile strength at 100 to 700 MPa confining pressure, both parallel and perpendicular to bedding. Loading and unloading path in uniaxial strain at 20 to 500 MPa confining pressure, both parallel and perpendicular to bedding. Tensile strength at ambient pressure, parallel and perpendicular to bedding. Shear and compressional wave velocities at confining pressures up to 1000 MPa parallel, at 45/sup 0/, and perpendicular to bedding. Results are presented and discussed. 32 refs., 10 figs., 10 tabs.

  6. High-pressure X-ray diffraction study of SrMoO{sub 4} and pressure-induced structural changes

    SciTech Connect (OSTI)

    Errandonea, Daniel [MALTA Consolider Team-Departamento de Fisica Aplicada-ICMUV, Universitat de Valencia, Edificio de Investigacion, c/Dr. Moliner 50, 46100 Burjassot, Valencia (Spain)], E-mail: daniel.errandonea@uv.es; Kumar, Ravhi S. [Department of Physics and Astronomy, High Pressure Science and Engineering Center, University of Nevada, 4505 Maryland Parkway, Las Vegas, NV 89154-4002 (United States); Ma Xinghua; Tu Chaoyang [Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou, Fujian 350002 (China); Graduated School of Chinese Academy of Science, 100039 Beijing (China)

    2008-02-15T23:59:59.000Z

    SrMoO{sub 4} was studied under compression up to 25 GPa by angle-dispersive X-ray diffraction. A phase transition was observed from the scheelite-structured ambient phase (space group I4{sub 1}/a) to a monoclinic fergusonite phase (space group I2/a) at 12.2(9) GPa. The unit-cell parameters of the high-pressure phase are a=5.265(9) A, b=11.191(9) A, c=5.195 (5) A, and {beta}=90.9(1){sup o}, Z=4 at 13.1 GPa. There is no significant volume collapse at the phase transition. No additional phase transitions were observed and on release of pressure the initial phase is recovered, implying that the observed structural modifications are reversible. The reported transition appeared to be a ferroelastic second-order transformation producing a structure that is a monoclinic distortion of the low-pressure phase and was previously observed in compounds isostructural to SrMoO{sub 4}. A possible mechanism for the transition is proposed and its character is discussed in terms of the present data and the Landau theory. Finally, the room temperature equation of states is reported and the anisotropic compressibility of the studied crystal is discussed in terms of the compression of the Sr-O and Mo-O bonds. - Graphical abstract: The evolution of the structure of SrMoO{sub 4} upon compression was established using synchrotron X-ray diffraction and a diamond-anvil cell. A pressure-induced phase transition was found involving a symmetry decrease from tetragonal to monoclinic. A transition mechanism is proposed and its ferroelastic character is discussed in terms of the Landau theory.

  7. The effect of high-pressure injection of gas on the reservoir volume factor of a crude oil 

    E-Print Network [OSTI]

    Honeycutt, Baxter Bewitt

    1957-01-01T23:59:59.000Z

    THE EFFECT OF HIGH-PRESSURE INJECTION OF GAS ON THE RESERVOIR VOLUME FACTOR OF A CRUDE OIL A Thesis By+ BAXTER DS'kONEYCUTT o Submitted to the Graduate School of the Agricultural and Mechanical College of Texas in partial fulfillment... of the requirements for the degree of MASTER OF SCIENCE August, i957 Major Subject: Petroleum Engineering THE EFFECT OF HIGH-PRESSURE INJECTION OF GAS ON THE RESERVOIR VOLUME FACTOR OF A CRUDE OIL A Thesis By BAXTER D. HONEYCUTT Appro d as to style...

  8. Benzene under High Pressure: a Story of Molecular Crystals Transforming to Saturated Networks, with a Possible Intermediate Metallic Phase

    SciTech Connect (OSTI)

    Wen, Xiao-Dong [Cornell Univ., Ithaca, NY (United States). Lab. of Atomic and Solid State Physics (LASSP) and Cornell Center for Materials Research (CCMR); Hoffmann, Roald [Cornell Univ., Ithaca, NY (United States). Lab. of Atomic and Solid State Physics (LASSP) and Cornell Center for Materials Research (CCMR); Ashcroft, N. W. [Cornell Univ., Ithaca, NY (United States). Lab. of Atomic and Solid State Physics (LASSP) and Cornell Center for Materials Research (CCMR)

    2011-06-15T23:59:59.000Z

    In a theoretical study, benzene is compressed up to 300 GPa. The transformations found between molecular phases generally match the experimental findings in the moderate pressure regime (<20 GPa): phase I (Pbca) is found to be stable up to 4 GPa, while phase II (P43212) is preferred in a narrow pressure range of 4–7 GPa. Phase III (P21/c) is at lowest enthalpy at higher pressures. Above 50 GPa, phase V (P21 at 0 GPa; P21/c at high pressure) comes into play, slightly more stable than phase III in the range of 50–80 GP, but unstable to rearrangement to a saturated, four-coordinate (at C), one-dimensional polymer. Actually, throughout the entire pressure range, crystals of graphane possess lower enthalpy than molecular benzene structures; a simple thermochemical argument is given for why this is so. In several of the benzene phases there nevertheless are substantial barriers to rearranging the molecules to a saturated polymer, especially at low temperatures. Even at room temperature these barriers should allow one to study the effect of pressure on the metastable molecular phases. Molecular phase III (P21/c) is one such; it remains metastable to higher pressures up to ?200 GPa, at which point it too rearranges spontaneously to a saturated, tetracoordinate CH polymer. At 300 K the isomerization transition occurs at a lower pressure. Nevertheless, there may be a narrow region of pressure, between P = 180 and 200 GPa, where one could find a metallic, molecular benzene state. We explore several lower dimensional models for such a metallic benzene. We also probe the possible first steps in a localized, nucleated benzene polymerization by studying the dimerization of benzene molecules. Several new (C6H6)2 dimers are predicted.

  9. High-pressure science gets super-sized | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    10 megabars, to probe materials at conditions corresponding to the core of gas giant planets, such as Uranus and Neptune, which have pressures of about seven megabars." Previous...

  10. First principle study of elastic and thermodynamic properties of FeB{sub 4} under high pressure

    SciTech Connect (OSTI)

    Zhang, Xinyu, E-mail: xyzhang@ysu.edu.cn, E-mail: jiaqianqin@gmail.com, E-mail: riping@ysu.edu.cn; Ning, Jinliang; Sun, Xiaowei; Li, Xinting; Ma, Mingzhen; Liu, Riping, E-mail: xyzhang@ysu.edu.cn, E-mail: jiaqianqin@gmail.com, E-mail: riping@ysu.edu.cn [State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Qin, Jiaqian, E-mail: xyzhang@ysu.edu.cn, E-mail: jiaqianqin@gmail.com, E-mail: riping@ysu.edu.cn [Metallurgy and Materials Science Research Institute, Chulalongkorn University, Bangkok 10330 (Thailand); State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China)

    2013-11-14T23:59:59.000Z

    The elastic properties, elastic anisotropy, and thermodynamic properties of the lately synthesized orthorhombic FeB{sub 4} at high pressures are investigated using first-principles density functional calculations. The calculated equilibrium parameters are in good agreement with the available experimental and theoretical data. The obtained normalized volume dependence of high pressure is consistent with the previous experimental data investigated using high-pressure synchrotron x-ray diffraction. The complete elastic tensors and crystal anisotropies of the FeB{sub 4} are also determined in the pressure range of 0–100?GPa. By the elastic stability criteria and vibrational frequencies, it is predicted that the orthorhombic FeB{sub 4} is stable up to 100 GPa. In addition, the calculated B/G ratio reveals that FeB{sub 4} possesses brittle nature in the range of pressure from 0 to 100?GPa. The calculated elastic anisotropic factors suggest that FeB{sub 4} is elastically anisotropic. By using quasi-harmonic Debye model, the compressibility, bulk modulus, the coefficient of thermal expansion, the heat capacity, and the Grüneisen parameter of FeB{sub 4} are successfully obtained in the present work.

  11. Ceramic-metallic coatings by electron beam physical vapor deposition (EB-PVD) process

    SciTech Connect (OSTI)

    Wolfe, D.E.; Singh, J. [Pennsylvania State Univ., State College, PA (United States)

    1995-12-31T23:59:59.000Z

    Electron Beam Physical Vapor Deposition (EB-PVD) process is considered to be a technology that has overcome some of the difficulties or problems associated with the chemical vapor deposition (CVD), physical vapor deposition (PVD) and metal spray processes. The EB-PVD process offers many desirable characteristics such as relatively high deposition rates (up to 100-150 {mu}m/minute with an evaporation rate {approx}10-15 Kg/hour,) dense coatings, precise compositional control, columnar and poly-crystalline microstructure, low contamination, and high thermal efficiency. Various metallic and ceramic coatings (oxides, carbides, nitrides) can be deposited at relatively low temperatures. Even elements with low vapor pressure such as molybdenum, tungsten, and carbon are readily evaporated by this process. In addition, EB-PVD is capable of producing multi-layered laminated metallic/ceramic coatings on large components by changing the EB-PVD processing conditions such as ingot composition, part manipulation, and electron beam energy. Attachment of an ion assisted beam source to the EB-PVD offers additional benefits such as dense coatings with improved adhesion. In addition, textured coatings can be obtained that are desirable in many applications such as cutting tools. This laboratory has started a new thrust in the coating area by the EB-PVD process. The microstructure of thermal barrier ceramic coatings (i.e., yttria stabilized zirconia) developed by the EB-PVD process will be presented.

  12. Effect of high pressure homogenization on the physical properties of milk

    E-Print Network [OSTI]

    Gonzalez De Cossio, Carlos

    1994-01-01T23:59:59.000Z

    Milk was homogenized at pressures ranging from 17.2 MPa to 100 MPa to determine the effect of homogenization pressure on the fat globule size distribution, viscosity, color, and temperature changes in milk. Milk containing 0, 1.5 and 3.0% milk fat...

  13. Influence of dissociative recombination on the LTE of argon high-frequency plasmas at atmospheric pressure

    E-Print Network [OSTI]

    Boyer, Edmond

    at atmospheric pressure A. Sáinz1 , J. Margot2 , M. C. García1 , M. D. Calzada1 1 Grupo de Espectroscopía de influencing its analytical performances are the electron density (ne) and temperature (Te), as well as the gas+ ) are also expected to play an important role in the discharge kinetics. At atmospheric pressure

  14. Diamond-anvil high-pressure cell with improved x-ray collimation system

    SciTech Connect (OSTI)

    Schiferl, D.; Olinger, B.W.; Livingston, R.W.

    1986-07-22T23:59:59.000Z

    This patent describes a diamond-anvil high-pressure cell having a tubular piston and a cylinder in which the piston is slidable to effect compression of a pair of opposed diamonds located between the piston and the cylinder. The piston includes a central bore opening on one end, an adjustable X-ray collimation system comprising a tubular insert engageable in the bore of the piston, the insert including a central bore and having first and second ends, with the first end of the insert being closest to the opposed diamonds and the second end of the insert extending out of the open end of the piston, a collimator insertable in the bore of the tubular insert. The collimator has a central bore and having first and second ends corresponding respectively with the first and second ends of the insert, elastomeric pivot means mounted in the bore of the insert at the first end of the insert for flexibly retaining the first end of the collimator while allowing the collimator to pivot within the pivot means, and adjustable locking means located at the second end of the insert for adjusting and securing the second end of the collimator so as to be in alignment with the opposed diamonds.

  15. An improved measurement of electron-ion recombination in high-pressure xenon gas

    E-Print Network [OSTI]

    NEXT Collaboration; L. Serra; M. Sorel; V. Álvarez; F. I. G. Borges; M. Camargo; S. Cárcel; S. Cebrián; A. Cervera; C. A. N. Conde; T. Dafni; J. Díaz; R. Esteve; L. M. P. Fernandes; P. Ferrario; A. L. Ferreira; E. D. C. Freitas; V. M. Gehman; A. Goldschmidt; J. J. Gómez-Cadenas; D. González-Díaz; R. M. Gutiérrez; J. Hauptman; J. A. Hernando Morata; D. C. Herrera; I. G. Irastorza; L. Labarga; A. Laing; I. Liubarsky; N. Lopez-March; D. Lorca; M. Losada; G. Luzón; A. Marí; J. Martín-Albo; G. Martínez-Lema; A. Martínez; T. Miller; F. Monrabal; M. Monserrate; C. M. B. Monteiro; F. J. Mora; L. M. Moutinho; J. Muñoz Vidal; M. Nebot-Guinot; D. Nygren; C. A. B. Oliveira; J. Pérez; J. L. Pérez Aparicio; M. Querol; J. Renner; L. Ripoll; A. Rodríguez; J. Rodríguez; F. P. Santos; J. M. F. dos Santos; D. Shuman; A. Simón; C. Sofka; J. F. Toledo; J. Torrent; Z. Tsamalaidze; J. F. C. A. Veloso; J. A. Villar; R. Webb; J. T. White; N. Yahlali

    2015-02-03T23:59:59.000Z

    We report on results obtained with the NEXT-DEMO prototype of the NEXT-100 high-pressure xenon gas time projection chamber (TPC), exposed to an alpha decay calibration source. Compared to our previous measurements with alpha particles, an upgraded detector and improved analysis techniques have been used. We measure event-by-event correlated fluctuations between ionization and scintillation due to electron-ion recombination in the gas, with correlation coeffcients between -0.80 and -0.56 depending on the drift field conditions. By combining the two signals, we obtain a 2.8 % FWHM energy resolution for 5.49 MeV alpha particles and a measurement of the optical gain of the electroluminescent TPC. The improved energy resolution also allows us to measure the specific activity of the radon in the gas due to natural impurities. Finally, we measure the average ratio of excited to ionized atoms produced in the xenon gas by alpha particles to be $0.561\\pm 0.045$, translating into an average energy to produce a primary scintillation photon of $W_{\\rm ex}=(39.2\\pm 3.2)$ eV.

  16. Engineering properties of miniature cement - fly ash compacts prepared by high pressure compaction 

    E-Print Network [OSTI]

    Bormann, Jeffrey Ray

    1985-01-01T23:59:59.000Z

    ENGINEERING PROPERTIES OF MINIATURE CEMENT - FLY ASH COMPACTS PREPARED BY HIGH PRESSURE COMPACTION E NGIRPR OT SFMMAFU AEU C-ALEYY HDOBPvvIi va vGI ge(iD(vI oannItI au NId(R E)L xrP1IeRPvT 9(evP(n uDnuPnnBIrv au vGI eI0DPeIBIrvR uae vGI i...?H?? NId(R E)L xrP1IeRPvT oG(PeB(r au Ei1PRaeT oaBBPvvII? ?e? ??C? ?IiOIvvIe oDeeIrv 9e(8vP8IR (ri vGIaeT 8aruaeB va vGI 8ar8I9v vG(v uae R9I8P(nP?Ii DRIR ( 9aevn(ri 8IBIrv 8ar8eIvI B(vIeP(n ?PvG RveIrtvG (99ea(8GPrt ?????? 9RP B(T OI 9eaiD8Ii OT eIiD8...

  17. Properties of molecular solids and fluids at high pressure and temperatures. Progress report, July 1, 1989--July 1, 1992

    SciTech Connect (OSTI)

    Etters, R.D.

    1992-03-01T23:59:59.000Z

    This renewal request for DOE grant DE-FG02-86ER45238, is dedicated to providing a complete thermodynamic profile of solids fluids, and fluid mixtures, over a wide range of temperatures and pressures. We are partially motivated by technological interest in detonation, combustion, superhard high pressure materials, and high temperature superconductors, which are important components of interest of various DOE laboratories. Our work on fluids and solids, composed of simple molecules, involves the determination of structures, phase transitions, pressure-volume relations, phonon, vibron, and libron modes of excitation, sound velocities, specific heats, thermal expansion, virial coefficients, sublimation energies, and orientational translational, and magnetic correlations. We hope that the study of these systems under extreme thermodynamic conditions will lead to exotic new materials of value, as well as enhanced fundamental understanding.

  18. Equation of state of rhenium and application for ultra high pressure calibration

    SciTech Connect (OSTI)

    Anzellini, Simone; Dewaele, Agnès; Occelli, Florent; Loubeyre, Paul [CEA, DAM, DIF, F-91297 Arpajon (France); Mezouar, Mohamed [European Synchrotron Radiation Facility, BP220, 38043 Grenoble Cedex (France)

    2014-01-28T23:59:59.000Z

    The isothermal equation of state of rhenium has been measured by powder X-ray diffraction experiments up to 144?GPa at room temperature in a diamond anvil cell. A helium pressure transmitting medium was used to minimize the non-hydrostatic stress on the sample. The fit of pressure-volume data yields a bulk modulus K{sub 0}?=?352.6?GPa and a pressure derivative of the bulk modulus K?{sub 0}=4.56. This equation of state differs significantly from a recent determination [Dubrovinsky et al., Nat. Commun. 3, 1163 (2012)], giving here a lower pressure at a given volume. The possibility of using rhenium gasket X-ray diffraction signal, with the present equation of state, to evaluate multi-Mbar pressures in the chamber of diamond anvil cells is discussed.

  19. High pressure dynamics of hydrated protein in bio-protective trehalose environment

    E-Print Network [OSTI]

    S. O. Diallo; Q. Zhang; H. O'Neill; E. Mamontov

    2014-09-11T23:59:59.000Z

    We present a pressure dependence study of the dynamics of lysozyme protein powder immersed in deuterated $\\alpha$,$\\alpha$-trehalose environment via quasi-elastic neutron scattering (QENS). The goal is to assess the baro-protective benefits of trehalose on bio-molecules by comparing the findings with those of a trehalose-free reference study. While the mean-square displacement of the trehalose-free protein (hydrated to $d_{D_2O}\\simeq$40 w\\%) as a whole, is reduced by increasing pressure, the actual observable relaxation dynamics in the pico-(ps) to nano-seconds (ns) time range remains largely unaffected by pressure - up to the maximum investigated pressure of 2.78(2) Kbar. Our observation is independent of whether or not the protein is mixed with the deuterated sugar. This suggests that the hydrated protein's conformational states at atmospheric pressure remain unaltered by hydrostatic pressures, below 2.78 Kbar. We also found the QENS response to be totally recoverable after ambient pressure conditions are restored. Circular dichroism and neutron diffraction measurements confirm that the protein structural integrity is conserved and remains intact, after pressure is released. We observe however a clear narrowing of the quasi-elastic neutron (QENS) response as the temperature is decreased from 290 K to 230 K in both cases, which we parametrize using the Kohlrausch-Williams-Watts (KWW) stretched exponential model. Only the fraction of protons that are immobile on the accessible time window of the instrument, referred to as the elastic incoherent structure factor or (EISF) is observably sensitive to pressure, increasing only marginally but systematically with increasing pressure.

  20. CHEMISTRY OF IMPACT-GENERATED SILICATE MELT-VAPOR DEBRIS DISKS

    SciTech Connect (OSTI)

    Visscher, Channon [Department of Space Studies, Southwest Research Institute, Boulder, CO 80302 (United States); Fegley, Bruce Jr. [Planetary Chemistry Laboratory, Department of Earth and Planetary Sciences and McDonnell Center for Space Sciences, Washington University in St. Louis, St. Louis, MO 63130 (United States)

    2013-04-10T23:59:59.000Z

    In the giant impact theory for lunar origin, the Moon forms from material ejected by the impact into an Earth-orbiting disk. Here we report the initial results from a silicate melt-vapor equilibrium chemistry model for such impact-generated planetary debris disks. In order to simulate the chemical behavior of a two-phase (melt+vapor) disk, we calculate the temperature-dependent pressure and chemical composition of vapor in equilibrium with molten silicate from 2000 to 4000 K. We consider the elements O, Na, K, Fe, Si, Mg, Ca, Al, Ti, and Zn for a range of bulk silicate compositions (Earth, Moon, Mars, eucrite parent body, angrites, and ureilites). In general, the disk atmosphere is dominated by Na, Zn, and O{sub 2} at lower temperatures (<3000 K) and SiO, O{sub 2}, and O at higher temperatures. The high-temperature chemistry is consistent for any silicate melt composition, and we thus expect abundant SiO, O{sub 2}, and O to be a common feature of hot, impact-generated debris disks. In addition, the saturated silicate vapor is highly oxidizing, with oxygen fugacity (f{sub O{sub 2}}) values (and hence H{sub 2}O/H{sub 2} and CO{sub 2}/CO ratios) several orders of magnitude higher than those in a solar-composition gas. High f{sub O{sub 2}} values in the disk atmosphere are found for any silicate composition because oxygen is the most abundant element in rock. We thus expect high oxygen fugacity to be a ubiquitous feature of any silicate melt-vapor disk produced via collisions between rocky planets.