Powered by Deep Web Technologies
Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Microfluidic Polymer Valves - Energy Innovation Portal  

No electrical power is dissipated into the fluid during valve operation. The microvalve dielectric strength is comparable to glass.

2

Low energy ion beam assisted deposition of a spin valve  

Science Conference Proceedings (OSTI)

The spin dependent electron transport in giant magnetoresistive (GMR) multilayers is significantly affected by the atomic scale structure of their interfaces. Devices with atomically flat and chemically sharp interfaces are preferred for magnetic sensor and memory applications. Recent atomic simulations of the atom-by-atom assembly of these devices indicate that near optimal interfacial structures can be created using low energy, ion assisted vapor deposition techniques with ion energies in the 5-10 eV range. A recently developed biased target ion beam deposition system has been used to experimentally test this hypothesis. Prototypical Ta/NiFe/Co/Cu/Co/FeMn/Cu spin valve structures were first grown using (simultaneous) argon ion assistance during deposition of the Co/Cu/Co trilayer part of the spin valve multilayer. Assisting ion energies of around 10 eV resulted in structures with a 30% higher magnetoresistance ratio and significantly reduced coupling field compared to samples grown with no ion assistance or with ion energies above 15 eV. These results are consistent with the atomistic simulation predictions. Other promising ion assistance schemes identified by the simulations were then used to deposit the Ta, NiFe, FeMn, and the top copper layer. A near optimal strategy was identified that resulted in the further improvement of the GMR ratio.

Quan, J. J.; Wolf, S. A.; Wadley, H. N. G. [Department of Materials Science and Engineering, School of Engineering and Applied Science, University of Virginia, Charlottesville, Virginia 22903 (United States)

2007-04-01T23:59:59.000Z

3

American Valve: Proposed Penalty (2010-CW-1411) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

American Valve: Proposed Penalty (2010-CW-1411) American Valve: Proposed Penalty (2010-CW-1411) American Valve: Proposed Penalty (2010-CW-1411) September 8, 2010 DOE alleged in a Notice of Proposed Civil Penalty that American Valve, Inc. failed to certify a variety of showerheads as compliant with the applicable water conservation standards. DOE regulations require a manufacturer (which includes importers) to submit reports certifying that its products have been tested and meet the applicable water conservation standards. This civil penalty notice advises the company of the potential penalties and DOE's administrative process, including the company's right to a hearing. American Valve: Proposed Penalty (2010-CW-1411) More Documents & Publications American Valve: Order (2010-CW-1411) Afeel: Proposed Penalty (2010-CW-07/1414)

4

American Valve: Order (2010-CW-1411) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Valve had failed to certify that certain showerhead models comply with the applicable water conservation standards. The Order adopted a Compromise Agreement, which reflected...

5

Energy-Saving Control of Single-Rod Hydraulic Cylinders with Programmable Valves and Improved Working Mode Selection  

E-Print Network (OSTI)

tremendous flexibility to control the cylinder motion while decreasing the energy usage by utilizing and individual cylinder chamber pressure control for better energy saving. With a typical four-way directional energy usage. The programmable valve configuration used in this study is seen in Figure 1. Cylinder Valve

Yao, Bin

6

Safety valve  

SciTech Connect

The safety valve contains a resilient gland to be held between a valve seat and a valve member and is secured to the valve member by a sleeve surrounding the end of the valve member adjacent to the valve seat. The sleeve is movable relative to the valve member through a limited axial distance and a gap exists between said valve member and said sleeve.

Bergman, Ulf C. (Malmoe, SE)

1984-01-01T23:59:59.000Z

7

Plug valve  

SciTech Connect

This patent describes an improved plug valve wherein a novel shape for the valve plug and valve chamber provide mating surfaces for improved wear characteristics. The novel shape of the valve plug is a frustum of body of revolution of a curved known as a tractrix, a solid shape otherwise known as a peudosphere.

Wordin, J.J.

1989-11-07T23:59:59.000Z

8

Plug valve  

DOE Patents (OSTI)

An improved plug valve wherein a novel shape for the valve plug and valve chamber provide mating surfaces for improved wear characteristics. The novel shape of the valve plug is a frustum of a body of revolution of a curved known as a tractrix, a solid shape otherwise known as a peudosphere.

Wordin, John J. (Shelley, ID)

1989-01-01T23:59:59.000Z

9

Locascio, Cavanagh Assume New NIST Leadership Roles  

Science Conference Proceedings (OSTI)

... assurance tools in areas such as climate change, renewable energy, advanced materials ... two or more NIST laboratories, such as the Office of Law ...

2012-05-15T23:59:59.000Z

10

Fast valve  

DOE Patents (OSTI)

A fast valve is disclosed that can close on the order of 7 milliseconds. It is closed by the force of a compressed air spring with the moving parts of the valve designed to be of very light weight and the valve gate being of wedge shaped with O-ring sealed faces to provide sealing contact without metal to metal contact. The combination of the O-ring seal and an air cushion create a soft final movement of the valve closure to prevent the fast air acting valve from having a harsh closing. 4 figs.

Van Dyke, W.J.

1992-04-07T23:59:59.000Z

11

Fast valve  

DOE Patents (OSTI)

A fast valve is disclosed that can close on the order of 7 milliseconds. It is closed by the force of a compressed air spring with the moving parts of the valve designed to be of very light weight and the valve gate being of wedge shaped with O-ring sealed faces to provide sealing contact without metal to metal contact. The combination of the O-ring seal and an air cushion create a soft final movement of the valve closure to prevent the fast air acting valve from having a harsh closing.

Van Dyke, William J. (Grafton, VA)

1992-01-01T23:59:59.000Z

12

Quasi-Static Hydraulic Control Systems and Energy Savings Potential Using Independent Metering Four-Valve Assembly Configuration .  

E-Print Network (OSTI)

??In this research, the four valve independent metering configuration is to be investigated. The Independent metering concept will be emphasized and compared to spool valve… (more)

Shenouda, Amir

2006-01-01T23:59:59.000Z

13

U.S. Department of Energy Energy Efficiency and Renewable Energy  

E-Print Network (OSTI)

available (PHAST, Canary) Evaluate full bore rupture and 1" puncture Assume that nearest valve is closed

14

Piezoelectric valve  

DOE Patents (OSTI)

A motorized valve has a housing having an inlet and an outlet to be connected to a pipeline, a saddle connected with the housing, a turn plug having a rod, the turn plug cooperating with the saddle, and a drive for turning the valve body and formed as a piezoelectric drive, the piezoelectric drive including a piezoelectric generator of radially directed standing acoustic waves, which is connected with the housing and is connectable with a pulse current source, and a rotor operatively connected with the piezoelectric generator and kinematically connected with the rod of the turn plug so as to turn the turn plug when the rotor is actuated by the piezoelectric generator.

Petrenko, Serhiy Fedorovich

2013-01-15T23:59:59.000Z

15

Estimating the Annual Water and Energy Savings in Texas A & M University Cafeterias using Low Flow Pre-Rinse Spray Valves  

E-Print Network (OSTI)

Improving the efficiency of a Pre- Rinse Spray Valve (PRSV) is one of the most cost effective water conservation methods in the Food Services Industry. A significant contributor to this cost efficiency is the reduction in the energy costs required to provide the mandatory hot water. This research paper estimates the potential quantity and dollar value of the water and energy that can be saved annually in Texas A&M University's dining services with the installation of low flow pre-rinse spray valves. The data collection was obtained from four of Texas A&M University's Dining Services facilities. The annual savings were estimated by contrasting the water consumption of the existing T & S Brass B 0107-M PRSVs with the latest and most advanced available low flow T and S Brass B 0107-C PRSV. The annual water consumption of the existing and new PRSVs were predicted by measuring an individual average flow rate for each and observing the number of hours per day the PRSV would be used. The observed and measured values were extrapolated to amount rates to determine cost savings. The dollar value was ascertained using the utility cost data recorded over a semester by the Facilities Coordinator of the Department of Dining Services. The findings of this study show that the water savings from a single PRSV could lead to an estimated annual saving ranging between 46% and 78% of the current operation cost. The T & S Brass B 0107-C PRSV is currently priced between $52- $60 per valve resulting in a payback period ranging between 1.5-6 months per valve. If every valve on campus was replaced, the University could reap a savings in the range of $ 5,400- $22,590 over the 5 year useful life of the valve, having initially invested less than $550.

Rebello, Harsh Varun

2010-05-01T23:59:59.000Z

16

Plasma valve  

DOE Patents (OSTI)

A plasma valve includes a confinement channel and primary anode and cathode disposed therein. An ignition cathode is disposed adjacent the primary cathode. Power supplies are joined to the cathodes and anode for rapidly igniting and maintaining a plasma in the channel for preventing leakage of atmospheric pressure through the channel.

Hershcovitch, Ady (Mount Sinai, NY); Sharma, Sushil (Hinsdale, IL); Noonan, John (Naperville, IL); Rotela, Elbio (Clarendon Hills, IL); Khounsary, Ali (Hinsdale, IL)

2003-01-01T23:59:59.000Z

17

A co-rotational 8-node degenerated thin-walled element with assumed natural strain and enhanced assumed strain  

Science Conference Proceedings (OSTI)

In recent years, solid-shell elements with the absence of the rotational degrees of freedom have considerable attentions in analyzing thin structures. In this paper, the non-linear formulation of a co-rotational 8-node degenerated thin-walled element ... Keywords: 8-Node solid element, Assumed natural strains, Co-rotational method, Enhanced assumed strains, Geometrical nonlinearity

Pramin Norachan; Songsak Suthasupradit; Ki-Du Kim

2012-03-01T23:59:59.000Z

18

Artificial Heart Valve Design  

E-Print Network (OSTI)

Artificial Heart Valve Design Your Chance to be a Biomedical Engineer #12;Circulatory System Video #12;What is a Heart Valve? · Heart Valve Video #12;#12;What Does a Heart Valve Do? · Maintain the one direction flow of blood through the heart · Heart valves allow blood to flow through in a forward direction

Provancher, William

19

Nuclear radiation actuated valve  

DOE Patents (OSTI)

A nuclear radiation actuated valve for a nuclear reactor. The valve has a valve first part (such as a valve rod with piston) and a valve second part (such as a valve tube surrounding the valve rod, with the valve tube having side slots surrounding the piston). Both valve parts have known nuclear radiation swelling characteristics. The valve's first part is positioned to receive nuclear radiation from the nuclear reactor's fuel region. The valve's second part is positioned so that its nuclear radiation induced swelling is different from that of the valve's first part. The valve's second part also is positioned so that the valve's first and second parts create a valve orifice which changes in size due to the different nuclear radiation caused swelling of the valve's first part compared to the valve's second part. The valve may be used in a nuclear reactor's core coolant system.

Christiansen, David W. (Kennewick, WA); Schively, Dixon P. (Richland, WA)

1985-01-01T23:59:59.000Z

20

Replace Pressure-Reducing Valves with Backpressure Turbogenerators (International Fact Sheet), Energy Tips-Steam, Steam Tip Sheet #20c  

SciTech Connect

This English/Chinese ITP steam tip sheet on replacing pressure-reducing valves provides how-to advice for improving industrial steam systems using low-cost, proven practices and technologies.

Not Available

2010-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Improved plug valve  

DOE Patents (OSTI)

An improved plug valve wherein a novel shape for the valve plug and valve chamber provide mating surfaces for improved wear characteristics is described. The novel shape of the valve plug is a frustum of a body of revolution of a curve known as a tractrix, a solid shape otherwise known as a pseudosphere.

Wordin, J.J.

1986-05-09T23:59:59.000Z

22

Rotary pneumatic valve  

DOE Patents (OSTI)

A rotary pneumatic valve which is thrust balanced and the pneumatic pressure developed produces only radial loads on the valve cylinder producing negligible resistance and thus minimal torque on the bearings of the valve. The valve is multiplexed such that at least two complete switching cycles occur for each revolution of the cylinder spindle. 4 figs.

Hardee, H.C.

1989-08-02T23:59:59.000Z

23

Vacuum breaker valve assembly  

DOE Patents (OSTI)

Breaker valve assemblies for a simplified boiling water nuclear reactor are described. The breaker valve assembly, in one form, includes a valve body and a breaker valve. The valve body includes an interior chamber, and an inlet passage extends from the chamber and through an inlet opening to facilitate transporting particles from outside of the valve body to the interior chamber. The breaker valve is positioned in the chamber and is configured to substantially seal the inlet opening. Particularly, the breaker valve includes a disk which is sized to cover the inlet opening. The disk is movably coupled to the valve body and is configured to move substantially concentrically with respect to the valve opening between a first position, where the disk completely covers the inlet opening, and a second position, where the disk does not completely cover the inlet opening.

Thompson, Jeffrey L. (San Jose, CA); Upton, Hubert Allen (Morgan Hill, CA)

1999-04-27T23:59:59.000Z

24

Vacuum breaker valve assembly  

Science Conference Proceedings (OSTI)

Breaker valve assemblies for a simplified boiling water nuclear reactor are described. The breaker valve assembly, in one form, includes a valve body and a breaker valve. The valve body includes an interior chamber, and an inlet passage extends from the chamber and through an inlet opening to facilitate transporting particles from outside of the valve body to the interior chamber. The breaker valve is positioned in the chamber and is configured to substantially seal the inlet opening. Particularly, the breaker valve includes a disk which is sized to cover the inlet opening. The disk is movably coupled to the valve body and is configured to move substantially concentrically with respect to the valve opening between a first position, where the disk completely covers the inlet opening, and a second position, where the disk does not completely cover the inlet opening. 1 fig.

Thompson, J.L.; Upton, H.A.

1999-04-27T23:59:59.000Z

25

Micro-valve pump light valve display  

DOE Patents (OSTI)

In this invention, a flat panel display incorporates a plurality of micro-pump light valves (MLV`s) to form pixels for recreating an image. Each MLV consists of a dielectric drop sandwiched between substrates, at least one of which is transparent, a holding electrode for maintaining the drop outside a viewing area, and a switching electrode from accelerating the drop from a location within the holding electrode to a location within the viewing area. The substrates may further define non-wetting surface areas to create potential energy barriers to assist in controlling movement of the drop. The forces acting on the drop are quadratic in nature to provide a nonlinear response for increased image contrast. A crossed electrode structure can be used to activate the pixels whereby a large flat panel display is formed without active driver components at each pixel.

Lee, Yee-Chun

1991-01-15T23:59:59.000Z

26

Micro-valve pump light valve display  

DOE Patents (OSTI)

In this invention, a flat panel display incorporates a plurality of micro-pump light valves (MLV's) to form pixels for recreating an image. Each MLV consists of a dielectric drop sandwiched between substrates, at least one of which is transparent, a holding electrode for maintaining the drop outside a viewing area, and a switching electrode from accelerating the drop from a location within the holding electrode to a location within the viewing area. The substrates may further define non-wetting surface areas to create potential energy barriers to assist in controlling movement of the drop. The forces acting on the drop are quadratic in nature to provide a nonlinear response for increased image contrast. A crossed electrode structure can be used to activate the pixels whereby a large flat panel display is formed without active driver components at each pixel.

Lee, Yee-Chun.

1991-01-15T23:59:59.000Z

27

Micro-valve pump light valve display  

DOE Patents (OSTI)

A flat panel display incorporates a plurality of micro-pump light valves (MLV's) to form pixels for recreating an image. Each MLV consists of a dielectric drop sandwiched between substrates, at least one of which is transparent, a holding electrode for maintaining the drop outside a viewing area, and a switching electrode from accelerating the drop from a location within the holding electrode to a location within the viewing area. The sustrates may further define non-wetting surface areas to create potential energy barriers to assist in controlling movement of the drop. The forces acting on the drop are quadratic in nature to provide a nonlinear response for increased image contrast. A crossed electrode structure can be used to activate the pixels whereby a large flat panel display is formed without active driver components at each pixel.

Yeechun Lee.

1993-01-19T23:59:59.000Z

28

By-pass valve  

Science Conference Proceedings (OSTI)

An improved by-pass valve (1) for use in an automobile exhaust system (Es) comprises an air inlet (7) connected to an air pump (Ap), first and second air outlets (15,23) respectively connected to first and second portions (P1,p2) of a catalytic converter (Cc) and a third outlet (33) through which air is dumped to atmosphere. Air is directed from the inlet to the first outlet when engine temperature is less than a predetermined value and from the inlet to the second outlet when engine temperature reaches the predetermined value. A first and normally closed valve (81) is intermediate the air inlet and the first and second outlets and a second and normally open valve (83) is intermediate the air inlet and the third outlet. The first valve is opened and the second valve closed when engine vacuum exceeds a predetermined level so air flows to either the first or second outlet. The second valve is reopened whenever the outlet to which air is directed is blocked so air is dumped to atmosphere. To accomplish this, the first valve is mounted on the first section (111) of a split shaft (109) and the second valve is mounted on a second shaft section (113). The sections are movable in unison to open the first valve, but the second section is movable relative to the first section when a blockage occurs to reopen the second valve.

Williamson, R.E.

1981-01-06T23:59:59.000Z

29

Effect of reactor conditions on MSIV (main steam isolation valves)-ATWS power level  

SciTech Connect

In a boiling water reactor (BWR) when there is closure of the main steam isolation valves (MSIVs), the energy generated in the core will be transferred to the pressure suppression pool (PSP) via steam flows out of the relief valves. The pool has limited capacity as a heat sink and hence, if there is no reactor trip (an ATWS event), there is the possibility that the pool temperature may rise beyond acceptable limits. The present study was undertaken to determine how the initial reactor conditions affect the power during an MSIV-ATWS event. The time of interest is during the 20-30 minute period when it is assumed that the reactor is in a quasi-equilibrium condition with the water level and pressure fixed, natural circulation conditions and no control rod movement or significant boron in the core. The initial conditions of interest are the time during the cycle and the operating state. 4 refs., 2 tabs.

Diamond, D.J.

1987-01-01T23:59:59.000Z

30

A WEAR MODEL FOR DIESEL ENGINE EXHAUST VALVES  

DOE Green Energy (OSTI)

The work summarized here comprises the concluding effort of a multi-year project, funded by the U.S. Department of Energy, Office of Vehicle Technologies. It supports the development of a better understanding of advanced diesel engine designs in which enhanced power density, energy efficiency, and emissions control place increasing demands upon the durability of engine materials. Many kinds of metallic alloys are used in engines depending on the operating stresses, temperatures, and chemical environments. Exhaust valves, for example, are subjected to high temperatures and repetitive surface contacts that place demands on durability and frictional characteristics of the materials. Valves must continue to seal the combustion chamber properly for thousands of hours of cyclic engine operation and under varying operating conditions. It was the focus of this effort to understand the wear processes in the valve-seat area and to develop a model for the surface deformation and wear of that important interface. An annotated bibliography is provided to illustrate efforts to understand valve wear and to investigate the factors of engine operation that affect its severity and physical manifestation. The project for which this modeling effort was the final task, involved construction of a high-temperature repetitive impact test system as well as basic tribology studies of the combined processes of mechanical wear plus oxidation at elevated temperatures. Several publications resulted from this work, and are cited in this report. The materials selected for the experimental work were high-performance alloys based on nickel and cobalt. In some cases, engine-tested exhaust valves were made available for wear analysis and to ensure that the modes of surface damage produced in experiments were simulative of service. New, production-grade exhaust valves were also used to prepare test specimens for experimental work along with the other alloy samples. Wear analysis of valves and seats run for hundreds of hours in heavy-duty diesels provided insights into the kinds of complexity that the contact conditions in engines can produce, and suggested the physical basis for the current approach to modeling. The model presented here involves four terms, two representing the valve response and two for its mating seat material. The model's structure assumes that wear that takes place under a complex combination of plastic deformation, tangential shear, and oxidation. Tribolayers form, are removed, and may reform. Layer formation affects the friction forces in the interface, and in turn, the energy available to do work on the materials to cause wear. To provide friction data for the model at various temperatures, sliding contact experiments were conducted from 22 to 850 C in a pin-on-disk apparatus at ORNL. In order to account for the behavior of different materials and engine designs, parameters in all four terms of the model can be adjusted to account for wear-in and incubation periods before the dominant wear processes evolve to their steady-state rates. For example, the deformation rate is assumed to be maximum during the early stages of operation, and then, due to material work-hardening and the increase in nominal contact area (which reduces the load per unit area), decreases to a lower rate at long times. Conversely, the rate of abrasion increases with time or number of cycles due to the build-up of oxides and tribo-layers between contact surfaces. The competition between deformation and abrasion results in complex, non-linear behavior of material loss per cycle of operation. Furthermore, these factors are affected by valve design features, such as the angle of incline of the valve seat. Several modeling scenarios are presented to demonstrate how the wear profile versus number of cycles changes in response to: (a) different relative abrasion rates of the seat and valve materials, (b) the friction coefficient as a function of temperature, (c) the relative deformation contribution of valve and seat materials, and (d) an interruption in the dominant we

Blau, Peter Julian [ORNL

2009-11-01T23:59:59.000Z

31

Statistical Performance Evaluation Of Soft Seat Pressure Relief Valves  

SciTech Connect

Risk-based inspection methods enable estimation of the probability of failure on demand for spring-operated pressure relief valves at the United States Department of Energy's Savannah River Site in Aiken, South Carolina. This paper presents a statistical performance evaluation of soft seat spring operated pressure relief valves. These pressure relief valves are typically smaller and of lower cost than hard seat (metal to metal) pressure relief valves and can provide substantial cost savings in fluid service applications (air, gas, liquid, and steam) providing that probability of failure on demand (the probability that the pressure relief valve fails to perform its intended safety function during a potentially dangerous over pressurization) is at least as good as that for hard seat valves. The research in this paper shows that the proportion of soft seat spring operated pressure relief valves failing is the same or less than that of hard seat valves, and that for failed valves, soft seat valves typically have failure ratios of proof test pressure to set pressure less than that of hard seat valves.

2013-03-26T23:59:59.000Z

32

Simulant Development for Hanford Tank Farms Double Valve Isolation (DVI) Valves Testing  

SciTech Connect

Leakage testing of a representative sample of the safety-significant isolation valves for Double Valve Isolation (DVI) in an environment that simulates the abrasive characteristics of the Hanford Tank Farms Waste Transfer System during waste feed delivery to the Waste Treatment and Immobilization Plant (WTP) is to be conducted. The testing will consist of periodic leak performed on the DVI valves after prescribed numbers of valve cycles (open and close) in a simulated environment representative of the abrasive properties of the waste and the Waste Transfer System. The valve operations include exposure to cycling conditions that include gravity drain and flush operation following slurry transfer. The simulant test will establish the performance characteristics and verify compliance with the Documented Safety Analysis. Proper simulant development is essential to ensure that the critical process streams characteristics are represented, National Research Council report “Advice on the Department of Energy's Cleanup Technology Roadmap: Gaps and Bridges”

Wells, Beric E.

2012-12-21T23:59:59.000Z

33

Solid handling valve  

DOE Patents (OSTI)

The present invention is directed to a solids handling valve for use in combination with lock hoppers utilized for conveying pulverized coal to a coal gasifier. The valve comprises a fluid-actuated flow control piston disposed within a housing and provided with a tapered primary seal having a recessed seat on the housing and a radially expandable fluid-actuated secondary seal. The valve seals are highly resistive to corrosion, erosion and abrasion by the solids, liquids, and gases associated with the gasification process so as to minimize valve failure.

Williams, William R. (Morgantown, WV)

1979-01-01T23:59:59.000Z

34

Compact gate valve  

DOE Patents (OSTI)

This invention relates to a double-disc gate valve which is compact, comparatively simple to construct, and capable of maintaining high closing pressures on the valve discs with low frictional forces. The valve casing includes axially aligned ports. Mounted in the casing is a sealed chamber which is pivotable transversely of the axis of the ports. The chamber contains the levers for moving the valve discs axially, and an actuator for the levers. When an external drive means pivots the chamber to a position where the discs are between the ports and axially aligned therewith, the actuator for the levers is energized to move the discs into sealing engagement with the ports.

Bobo, Gerald E. (Knoxville, TN)

1977-01-01T23:59:59.000Z

35

Tubing drain valve  

SciTech Connect

A method is described for operating a valve means. The valve means comprises a tubular piston movable within a tubular member suitable for use in a borehole pipe string to open and close a port through the wall of the tubular member. The method comprises: biassing the valve means in its closed position; pressurizing the interior of the piston to a predetermined pressure to overcome the biassing closed force and to actuate the valve means to its open position; biassing the valve means to its open position; and actuating the valve means to its closed position by engaging a first arm of a dog pivotally mounted on the piston with an engaging means insertable through the interior of the tubular piston; moving the piston relative to the tubular member; rotating the dog about its pivot to bring a second arm of the dog into contact with a detent in the tubular member; and applying sufficient force to the first arm to continue rotating the dog about the pivot, while engaging the detent with the second arm of the dog, in order to overcome the biassing open force to actuate the valve means to its closed position. A tubing drain valve suitable for use in a borehole pipe string, comprising: a sub suitable for incorporating within a borehole pipe string; and a port between the interior and the exterior of the sub; and valve means for opening and closing the port.

Soderberg, P.B.

1987-02-24T23:59:59.000Z

36

Corrosion of valve metals  

DOE Green Energy (OSTI)

A general survey related to the corrosion of valve metals or film-forming metals. The way these metals corrode with some general examples is described. Valve metals form relatively perfect oxide films with little breakdown or leakage when anodized. (FS)

Draley, J.E.

1976-01-01T23:59:59.000Z

37

Valve for abrasive material  

DOE Patents (OSTI)

A ball valve assembly for controlling the flow of abrasive particulates including an enlarged section at the bore inlet and an enlarged section at the bore outlet. A refractory ceramic annular deflector is positioned in each of the enlarged sections, substantially extending the useful life of the valve.

Gardner, Harold S. (Turtle Creek, PA)

1982-01-01T23:59:59.000Z

38

Dissolution Actuated Valve Sampler  

Engineers at the Savannah River National Laboratory (SRNL) have invented a new device for retrieving liquid samples.  The dissolution actuated valve sampler was developed to obtain pristine samples while operating without the assistance of a mast or ...

39

Flow metering valve  

DOE Patents (OSTI)

An apparatus for metering fluids at high pressures of about 20,000 to 60,000 psi is disclosed. The apparatus includes first and second plates which are positioned adjacent each other to form a valve chamber. The plates are made of materials which have substantially equal elastic properties. One plate has a planar surface area, and the other a recessed surface area defined by periphery and central lips. When the two plates are positioned in adjacent contacting relationship, a valve chamber is formed between the planar surface area and the recessed surface area. Fluid is introduced into the chamber and exits therefrom when a deformation occurs at positions where they no longer form a valve seat. This permits the metering of fluids at high pressures and at slow variable rates. Fluid then exits from the chamber until an applied external force becomes large enough to bring the valve seats back into contact.

Blaedel, Kenneth L. (Dublin, CA)

1985-01-01T23:59:59.000Z

40

Flow metering valve  

DOE Patents (OSTI)

An apparatus for metering fluids at high pressures of about 20,000 to 60,000 psi is disclosed. The apparatus includes first and second plates which are positioned adjacent each other to form a valve chamber. The plates are made of materials which have substantially equal elastic properties. One plate has a planar surface area, and the other a recessed surface area defined by periphery and central lips. When the two plates are positioned in adjacent contacting relationship, a valve chamber is formed between the planar surface area and the recessed surface area. Fluid is introduced into the chamber and exits therefrom when a deformation occurs at positions where they no longer form a valve seat. This permits the metering of fluids at high pressures and at slow variable rates. Fluid then exits from the chamber until an applied external force becomes large enough to bring the valve seats back into contact.

Blaedel, K.L.

1983-11-03T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Valve for gas centrifuges  

DOE Patents (OSTI)

The invention is a pneumatically operated valve assembly for simultaneously (1) closing gas-transfer lines connected to a gas centrifuge or the like and (2) establishing a recycle path between two of the lines so closed. The valve assembly is especially designed to be compact, fast-acting, reliable, and comparatively inexpensive. It provides large reductions in capital costs for gas-centrifuge cascades.

Hahs, Charles A. (Oak Ridge, TN); Burbage, Charles H. (Oak Ridge, TN)

1984-01-01T23:59:59.000Z

42

Low noise control valve  

SciTech Connect

Noise is one of the problems associated with the use of any type of control valve in systems involving the flow of fluids. The advent of OSHA standards has prompted control valve manufacturers to design valves with special trim to lower the sound pressure level to meet these standards. However, these levels are in some cases too high, particularly when a valve must be located in or near an area where people are working at tasks requiring a high degree of concentration. Such locations are found around and near research devices and in laboratory-office areas. This paper describes a type of fluid control device presently being used at PPL as a bypass control valve in deionized water systems and designed to reduce sound pressure levels considerably below OSHA standards. Details of the design and construction of this constant pressure drop variable flow control valve are contained in the text and are shown in photographs and drawings. Test data taken are included. (auth)

Christie, R.S.

1975-01-01T23:59:59.000Z

43

Fast closing valve  

DOE Patents (OSTI)

A valve is provided for protecting the high vacuum of a particle accelera in the event of air leakage, wherein the valve provides an axially symmetrical passage to avoid disturbance of the partical beam during normal operation, and yet enables very rapid and tight closure of the beam-carrying pipe in the event of air leakage. The valve includes a ball member (30) which can rotate between a first position wherein a bore (32) in the member is aligned with the beam pipe, and a second position out of line with the pipe. A seal member (38) is flexibly sealed to the pipe, and has a seal end which can move tightly against the ball member after the bore has rotated out of line with the pipe, to thereby assure that the seal member does not retard rapid rotation of the ball valve member. The ball valve member can be rapidly rotated by a conductive arm (40) fixed to it and which is rotated by the discharge of a capacitor bank through coils (44, 45) located adjacent to the arm.

Hanson, Clark L. (Livermore, CA)

1984-01-10T23:59:59.000Z

44

REACTOR SYSTEM AND CONTROL VALVE  

DOE Patents (OSTI)

Valves have been developed for controlling the flow of gaseous fluid through a passage or conduit. The valves have particular application in the cooling systems of gas; cooled reactors. (R.J.S.)

Fortescue, P.; Rickard, C.; Rose, D.

1963-01-01T23:59:59.000Z

45

Hydrogen gas relief valve  

SciTech Connect

An improved battery stack design for an electrochemical system having at least one cell from which a gas is generated and an electrolyte in communication with the cell is described. The improved battery stack design features means for defining a substantially closed compartment for containing the battery cells and at least a portion of the electrolyte for the system, and means in association with the compartment means for selectively venting gas from the interior of the compartment means in response to the level of the electrolyte within the compartment means. The venting means includes a relief valve having a float member which is actuated in response to the level of the electrolyte within the compartment means. This float member is adapted to close the relief valve when the level of the electrolyte is above a predetermined level and open the relief valve when the level of electrolyte is below this predetermined level.

Whittlesey, Curtis C. (Birmingham, MI)

1985-01-01T23:59:59.000Z

46

Self-regulating valve  

DOE Patents (OSTI)

A variable, self-regulating valve having a hydraulic loss coefficient proportional to a positive exponential power of the flow rate. The device includes two objects in a flow channel and structure which assures that the distance between the two objects is an increasing function of the flow rate. The range of spacing between the objects is such that the hydraulic resistance of the valve is an increasing function of the distance between the two objects so that the desired hydraulic loss coefficient as a function of flow rate is obtained without variation in the flow area.

Humphreys, D.A.

1982-07-20T23:59:59.000Z

47

Improved bellows sealed plug valve  

DOE Patents (OSTI)

It is an object of the present invention to provide a bellows sealed 1/4 turn valve wherein means are provided for translating linear motion to rotational motion between the bellows seal and the valve body. This paper details the features of the valve. 6 figs.

Dukas, S.J. Jr.

1989-10-29T23:59:59.000Z

48

Valve stem and packing assembly  

DOE Patents (OSTI)

A valve stem and packing assembly is provided in which a rotatable valve stem includes a first tractrix surface for sliding contact with a stem packing and also includes a second tractrix surface for sliding contact with a bonnet. Force is applied by means of a spring, gland flange, and gland on the stem packing so the stem packing seals to the valve stem and bonnet. This configuration serves to create and maintain a reliable seal between the stem packing and the valve stem. The bonnet includes a second complementary tractrix surface for contacting the second sliding tractrix surface, the combination serving as a journal bearing for the entire valve stem and packing assembly. The journal bearing so configured is known as a Schiele`s pivot. The Schiele`s pivot also serves to maintain proper alignment of the valve stem with respect to the bonnet. Vertical wear between the surfaces of the Schiele`s pivot is uniform at all points of contact between the second sliding tractrix surface and the second complementary tractrix surface of a bonnet. The valve stem is connected to a valve plug by means of a slip joint. The valve is opened and closed by rotating the valve stem. The slip joint compensates for wear on the Schiele`s pivot and on the valve plug. A ledge is provided on the valve bonnet for the retaining nut to bear against. The ledge prevents overtightening of the retaining nut and the resulting excessive friction between stem and stem packing.

Wordin, J.J.

1990-12-31T23:59:59.000Z

49

Valve for cryogenic service  

DOE Patents (OSTI)

This patent relates to a valve for use with a liquefied gas at cryogenic temperatures in which a pair of joined knife edges are bellows controlled to contact an indium alloy seat in an annular slot when flow is to be stopped. The sealing alloy may be renewed by heating in situ. (auth)

Worwetz, H.A.

1975-09-02T23:59:59.000Z

50

Valve for gas centrifuges  

DOE Patents (OSTI)

The invention is pneumatically operated valve assembly for simulatenously (1) closing gas-transfer lines connected to a gas centrifuge or the like and (2) establishing a recycle path between two on the lines so closed. The value assembly is especially designed to be compact, fast-acting, reliable, and comparatively inexpensive. It provides large reductions in capital costs for gas-centrifuge cascades.

Hahs, C.A.; Rurbage, C.H.

1982-03-17T23:59:59.000Z

51

Valve selection handbook. Third edition  

Science Conference Proceedings (OSTI)

This book covers the fundamentals of value construction and application, and analyzes the different hazards and requirements of all types of industrial fluid flow situations. This book expands the coverage of pressure relief valves and rupture discs. It includes a new section on damping valve chatter, which is a serious problem in installations such as atomic power plants where valve chatter could have catastrophic consequences to the safety of the plant. There is also new information on performance of spring-loaded pressure relief valves and a closer examination of valve selection with respect to rupture discs and explosion venting.

Zappe, R.W. (ICI Australia Operations Pty. Ltd. (AU))

1991-01-01T23:59:59.000Z

52

Dual valve well pump installation  

SciTech Connect

A reciprocating electric motor-pump assembly for lifting well fluid on downstroke of the motor pump assembly, the pump including a barrel below the motor having dual combined inlet and outlet valve means at the lower end thereof, the pump piston moving in the barrel having annular grooves therearound to prevent differential pressure sticking, the electric cable supplying the electric motor being tubular to vent the pump and prevent vacuum or gas lock, there being a packer about the valve barrel separating the outlet valve means thereabove from the inlet valve means therebelow and a packer above the motor about a production tubing including an upper standing valve.

Holm, D. R.

1985-10-22T23:59:59.000Z

53

Multi-port valve assembly  

DOE Patents (OSTI)

A multi-port fluid valve apparatus is used to control the flow of fluids through a plurality of valves and includes a web, which preferably is a stainless steel endless belt. The belt has an aperture therethrough and is progressed, under motor drive and control, so that its aperture is moved from one valve mechanism to another. Each of the valve mechanisms comprises a pair of valve blocks which are held in fluid-tight relationship against the belt. Each valve block consists of a block having a bore through which the fluid flows, a first seal surrounding the bore and a second seal surrounding the first seal, with the distance between the first and second seals being greater than the size of the belt aperture. In order to open a valve, the motor progresses the belt aperture to where it is aligned with the two bores of a pair of valve blocks, such alignment permitting a flow of the fluid through the valve. The valve is closed by movement of the belt aperture and its replacement, within the pair of valve blocks, by a solid portion of the belt.

Guggenheim, S. Frederic (Teaneck, NJ)

1986-01-01T23:59:59.000Z

54

Throttled Valve Cavitation and Erosion  

E-Print Network (OSTI)

The submitted manuscipt has been authored by a contmrctor of the US. Government under contract No. DE-AC05-840R21400. Accordingly, the U. S. Government retains a nonexclusive royalty-free license to publish or reproduce the published form of the contribution, or aflow others to do so, for US. Government pupose & 1. Background In November of 1988, Brunswick plant maintenance personnel discovered significant localized erosion of the valve body of a Unit I Residual Heat Removal (RHR) valve, 1-El 1-F017B (the maintenance was being performed to repair the valve stem and back seat). 1 The F017B valv'e is a 20-inch Rockwell angle globe valve that has been historically used to throttle RHR flow. Excessive throttling of the valve had resulted in cavitation-induced erosion damage to areas immediately downstream of the seat. Subsequent investigation indicated that erosion of valve bodies was a generic concern for the other RHR valves used in the same service (FO17A on Unit I and F017A and F017B on Unit 2). Brunswick personnel expanded the investigation to include another set of RHR valves that had also been used in throttling service. The F024A and F024B valves (from both Units), which are used for Suppression Pool Cooling, were also found to have been damaged by

Don Casada; Don Casada

1991-01-01T23:59:59.000Z

55

Fast-acting valve and uses thereof  

SciTech Connect

A very fast acting valve capable of producing a very well-defined plug of gas suitable for filling a theta pinch vacuum vessel is given. The valve requires no springs, instead being stopped mainly by a nonlinear force. Thus, the valve is not subject to bouncing; and the ratio of the size of the valve housing to the size of the valve stem is smaller than it would be if springs were needed to stop the valve stem. Furthermore, the valve can be used for thousands of valve firings with no apparent valve damage.

Meyer, James A. (Espanola, NM)

1982-01-01T23:59:59.000Z

56

Performance Characteristics of an Isothermal Freeze Valve  

Science Conference Proceedings (OSTI)

This document discusses performance characteristics of an isothermal freeze valve. A freeze valve has been specified for draining the DWPF melter at the end of its lifetime. Two freeze valve designs have been evaluated on the Small Cylindrical Melter-2 (SCM-2). In order to size the DWPF freeze valve, the basic principles governing freeze valve behavior need to be identified and understood.

Hailey, A.E.

2001-08-22T23:59:59.000Z

57

System for minimizing valve throttling losses in a steam turbine power plant  

SciTech Connect

A system which integrates the controls of a steam turbine power plant for minimizing power plant energy losses substantially caused by steam flow valve throttling is disclosed. The steam turbine power plant includes boiler pressure controls for controlling the boiler throttle pressure of a steam producing boiler and turbine-generator controls for positioning a plurality of turbine steam admission values to regulate the steam flow conducted through a steam turbine which governs the electrical energy generated by an electrical generator at a desired power generation level. The turbine-generator controls predetermine a plurality of valve position states to establish a predetermined valve grouping sequential positioning pattern for the steam admission valves to regulate steam flow through the steam turbine across the range of power generation, each predetermined state substantially corresponding to a minimum of valve throttling losses. The steam admission valves may be positioned at a present valve position state, which is other than one of the predetermined states, as a result of a change in desired power generation level. The disclosed system responds to this condition by governing the boiler pressure controls to adjust the boiler throttle pressure at a desired rate and in a direction to cause steam admission valves to be repositioned according to the sequential positioning pattern to a selected one of the predetermined efficient valve position states. The repositioning of the steam admission valves is performed by maintaining the generated energy substantially at the new desired power generation level.

Stern, L.P.; Johnson, S.J.

1979-12-18T23:59:59.000Z

58

B&W Y-12 assumes responsibility for protective force | Y-12 National  

NLE Websites -- All DOE Office Websites (Extended Search)

assumes ... assumes ... B&W Y-12 assumes responsibility for protective force Posted: October 29, 2012 - 4:30pm B&W Y-12 has assumed responsibility for the protective force at the Y-12 National Security Complex following a four-week transition from WSI Oak Ridge, the site's former subcontractor for security. During the transition, B&W Y-12 hired more than 560 WSI Oak Ridge employees. "The transition from WSI Oak Ridge to B&W Y-12 has gone very smoothly, and we welcome these new employees to the company," said Brigadier General (Ret.) Rod Johnson, Deputy General Manager for Security. "We've already seen improvements in security performance following previously announced contracting changes, and we believe we'll see additional successes with the protective force fully integrated into B&W Y-12."

59

Semi-active compressor valve  

SciTech Connect

A method and system for fine-tuning the motion of suction or discharge valves associated with cylinders of a reciprocating gas compressor, such as the large compressors used for natural gas transmission. The valve's primary driving force is conventional, but the valve also uses an electromagnetic coil to sense position of the plate (or other plugging element) and to provide an opposing force prior to impact.

Brun, Klaus (Helotes, TX); Gernentz, Ryan S. (San Antonio, TX)

2010-07-27T23:59:59.000Z

60

Semi-active compressor valve  

DOE Patents (OSTI)

A method and system for fine-tuning the motion of suction or discharge valves associated with cylinders of a reciprocating gas compressor, such as the large compressors used for natural gas transmission. The valve's primary driving force is conventional, but the valve also uses an electromagnetic coil to sense position of the plate (or other plugging element) and to provide an opposing force prior to impact.

Brun, Klaus (Helotes, TX); Gernentz, Ryan S. (San Antonio, TX)

2010-07-27T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Streamline coal slurry letdown valve  

DOE Patents (OSTI)

A streamlined coal slurry letdown valve is featured which has a two-piece throat comprised of a seat and seat retainer. The two-piece design allows for easy assembly and disassembly of the valve. A novel cage holds the two-piece throat together during the high pressure letdown. The coal slurry letdown valve has long operating life as a result of its streamlined and erosion-resistance surfaces.

Platt, Robert J. (Dover, NJ); Shadbolt, Edward A. (Basking Ridge, NJ)

1983-01-01T23:59:59.000Z

62

Streamline coal slurry letdown valve  

DOE Patents (OSTI)

A streamlined coal slurry letdown valve is featured which has a two-piece throat comprised of a seat and seat retainer. The two-piece design allows for easy assembly and disassembly of the valve. A novel cage holds the two-piece throat together during the high pressure letdown. The coal slurry letdown valve has long operating life as a result of its streamlined and erosion-resistance surfaces. 5 figs.

Platt, R.J.; Shadbolt, E.A.

1983-11-08T23:59:59.000Z

63

Valve stem and packing assembly  

SciTech Connect

A valve stem and packing assembly is provided in which a rotatable valve stem includes a first tractrix surface for sliding contact with a stem packing and also includes a second tractrix surface for sliding contact with a bonnet. Force is applied by means of a spring, gland flange, and gland on the stem packing so the stem packing seals to the valve stem and bonnet. This configuration serves to create and maintain a reliable seal between the stem packing and the valve stem. The bonnet includes a second complementary tractrix surface for contacting the second sliding tractrix surface, the combination serving as a journal bearing for the entire valve stem and packing assembly. The journal bearing so configured is known as a Schiele's pivot. The Schiele's pivot also serves to maintain proper alignment of the valve stem with respect to the bonnet. Vertical wear between the surfaces of the Schiele's pivot is uniform at all points of contact between the second sliding tractrix surface and the second complementary tractrix surface of a bonnet. The valve stem is connected to a valve plug by means of a slip joint. The valve is opened and closed by rotating the valve stem. The slip joint compensates for wear on the Schiele's pivot and on the valve plug. A ledge is provided on the valve bonnet for the retaining nut to bear against. The ledge prevents overtightening of the retaining nut and the resulting excessive friction between stem and stem packing.

Wordin, John J. (Bingham County, ID)

1991-01-01T23:59:59.000Z

64

Valve stem and packing assembly  

DOE Patents (OSTI)

A valve stem and packing assembly is provided in which a rotatable valve stem includes a first tractrix surface for sliding contact with a stem packing and also includes a second tractrix surface for sliding contact with a bonnet. Force is applied by means of a spring, gland flange, and gland on the stem packing so the stem packing seals to the valve stem and bonnet. This configuration serves to create and maintain a reliable seal between the stem packing and the valve stem. The bonnet includes a second complementary tractrix surface for contacting the second sliding tractrix surface, the combination serving as a journal bearing for the entire valve stem and packing assembly. The journal bearing so configured is known as a Schiele's pivot. The Schiele's pivot also serves to maintain proper alignment of the valve stem with respect to the bonnet. Vertical wear between the surfaces of the Schiele's pivot is uniform at all points of contact between the second sliding tractrix surface and the second complementary tractrix surface of a bonnet. The valve stem is connected to a valve plug by means of a slip joint. The valve is opened and closed by rotating the valve stem. The slip joint compensates for wear on the Schiele's pivot and on the valve plug. A ledge is provided on the valve bonnet for the retaining nut to bear against. The ledge prevents over tightening of the retaining nut and the resulting excessive friction between stem and stem packing. 2 figures.

Wordin, J.J.

1991-09-03T23:59:59.000Z

65

Valve stem and packing assembly  

DOE Patents (OSTI)

A valve stem and packing assembly is provided in which a rotatable valve stem includes a first tractrix surface for sliding contact with a stem packing and also includes a second tractrix surface for sliding contact with a bonnet. Force is applied by means of a spring, gland flange, and gland on the stem packing so the stem packing seals to the valve stem and bonnet. This configuration serves to create and maintain a reliable seal between the stem packing and the valve stem. The bonnet includes a second complementary tractrix surface for contacting the second sliding tractrix surface, the combination serving as a journal bearing for the entire valve stem and packing assembly. The journal bearing so configured is known as a Schiele's pivot. The Schiele's pivot also serves to maintain proper alignment of the valve stem with respect to the bonnet. Vertical wear between the surfaces of the Schiele's pivot is uniform at all points of contact between the second sliding tractrix surface and the second complementary tractrix surface of a bonnet. The valve stem is connected to a valve plug by means of a slip joint. The valve is opened and closed by rotating the valve stem. The slip joint compensates for wear on the Schiele's pivot and on the valve plug. A ledge is provided on the valve bonnet for the retaining nut to bear against. The ledge prevents overtightening of the retaining nut and the resulting excessive friction between stem and stem packing.

Wordin, J.J.

1990-01-01T23:59:59.000Z

66

All metal valve structure for gas systems  

DOE Patents (OSTI)

A valve assembly with a resilient metal seat member is disclosed for providing a gas-tight seal in a gas handling system. The valve assembly also includes a valve element for sealing against the valve seat member; and an actuating means for operating the valve element. The valve seat member is a one-piece stainless steel ring having a central valve port and peripheral mounting flange, and an annular corrugation in between. A groove between the first and second ridges serves as a flexure zone during operation of the valve member and thus provides the seating pressure between the inner ridge or valve seat and the valve element. The outer annular ridge has a diameter less than said valve element to limit the seating motion of the valve element, preventing non-elastic deformation of the seat member.

Baker, Ray W. (Hamilton, OH); Pawlak, Donald A. (Centerville, OH); Ramey, Alford J. (Miamisburg, OH)

1984-11-13T23:59:59.000Z

67

Proceedings of the 2nd symposium on valves for coal conversion and utilization  

SciTech Connect

The 2nd symposium on valves for coal conversion and utilization was held October 15 to 17, 1980. It was sponsored by the US Department of Energy, Morgantown Energy Technology Center, in cooperation with the Valve Manufacturers Association. Seventeen papers have been entered individually into EDB and ERA. (LTN)

Maxfield, D.A. (ed.)

1981-01-01T23:59:59.000Z

68

Valves - current operating experience of slurry valves (block and letdown) in coal liquefaction processes. Third quarter report  

Science Conference Proceedings (OSTI)

This paper summarizes the recent letdown and block valve experience in the liquefaction pilot plants. Also included is a brief description of the research and development activities on valves which are conducted in supporting laboratories. The purpose of the summary is to concentrate on critical component problems common to all liquefaction plants, to avoid duplication of efforts, and to help provide timely solutions to the valve problems. The main source of information used in this paper is the Minutes of the Critical Component and Materials Meeting which is sponsored by the Office of Coal Processing, Fossil Energy, Department of Energy. Other sources of information such as the technical progress reports are also included based on availability and relevance to topics covered in this paper. It is intended that this report will be followed by updates as pertinent information concerning valves becomes available. In the subsequent sections of this paper a brief outline of past valve studies is given as background material followed by a summary of the most recent valve operating experience at the liquefaction plants.

NONE

1996-07-01T23:59:59.000Z

69

Comparison of ELCAP data with lighting and equipment load levels and profiles assumed in regional models  

SciTech Connect

The analysis in this report was driven by two primary objectives: to determine whether and to what extent the lighting and miscellaneous equipment electricity consumption measured by metering in real buildings differs from the levels assumed in the various prototypes used in power forecasting; and to determine the reasons for those differences if, in fact, differences were found. 13 refs., 47 figs., 4 tabs.

Taylor, Z.T.; Pratt, R.G.

1990-09-01T23:59:59.000Z

70

Heart Valve Lesson Plan Biomedical Engineering  

E-Print Network (OSTI)

Heart Valve Lesson Plan Biomedical Engineering Objective · Introduce students to biomedical Learning Outcomes · Students will understand the role and function of heart valves. · Students will learn does a heart valve work? · Why do we need to replace heart valves? Time Required (Itemized) · Lecture

Provancher, William

71

Multi-port valve  

DOE Patents (OSTI)

A multi-port valve is described for regulating, as a function of ambient air having varying wind velocity and wind direction in an open-field control area, the distribution of a fluid, particularly carbon dioxide (CO{sub 2}) gas, in a fluid distribution system so that the control area remains generally at an elevated fluid concentration or level of said fluid. The multi-port valve generally includes a multi-port housing having a plurality of outlets there through disposed in a first pattern of outlets and at least one second pattern of outlets, and a movable plate having a plurality of apertures extending there through disposed in a first pattern of apertures and at least one second pattern of apertures. The first pattern of apertures being alignable with the first pattern of outlets and the at least one second pattern of apertures being alignable with the second pattern of outlets. The first pattern of apertures has a predetermined orientation with the at least one second pattern of apertures. For an open-field control area subject to ambient wind having a low velocity from any direction, the movable plate is positioned to equally distribute the supply of fluid in a fluid distribution system to the open-field control area. For an open-field control area subject to ambient wind having a high velocity from a given direction, the movable plate is positioned to generally distribute a supply of fluid in a fluid distribution system to that portion of the open-field control area located upwind. 7 figs.

Lewin, K.F.

1997-04-15T23:59:59.000Z

72

Multi-port valve  

DOE Patents (OSTI)

A multi-port valve for regulating, as a function of ambient air having varying wind velocity and wind direction in an open-field control area, the distribution of a fluid, particularly carbon dioxide (CO.sub.2) gas, in a fluid distribution system so that the control area remains generally at an elevated fluid concentration or level of said fluid. The multi-port valve generally includes a multi-port housing having a plurality of outlets therethrough disposed in a first pattern of outlets and at least one second pattern of outlets, and a movable plate having a plurality of apertures extending therethrough disposed in a first pattern of apertures and at least one second pattern of apertures. The first pattern of apertures being alignable with the first pattern of outlets and the at least one second pattern of apertures being alignable with the second pattern of outlets. The first pattern of apertures has a predetermined orientation with the at least one second pattern of apertures. For an open-field control area subject to ambient wind having a low velocity from any direction, the movable plate is positioned to equally distribute the supply of fluid in a fluid distribution system to the open-field control area. For an open-field control area subject to ambient wind having a high velocity from a given direction, the movable plate is positioned to generally distribute a supply of fluid in a fluid distribution system to that portion of the open-field control area located upwind.

Lewin, Keith F. (Calverton, NY)

1997-04-15T23:59:59.000Z

73

Robotic Digital Valve  

for the U.S. Department of Energy Market. Industrial 67%. Professional Service 19% Military 5% Domestic ... for the U.S. Department of Energy. For more information ...

74

Noninvasive valve monitor using alternating electromagnetic field  

SciTech Connect

One or more electrical coils are carefully located on the outside of a valve body. An alternating current passing through the coil(s) results in an alternating electromagnetic field being transmitted into the valve body and valve internals. The electromagnetic field varies in intensity and polarity in the valve. As the position of a valve internal part is changed, the electromagnetic field throughout the valve body and its internals is altered. A passive receiver coil carefully located on the outside of the valve body detects the intensity of the electromagnetic field at that location as an induced electrical voltage in the coil. With the change in position of the valve internal part, there is a corresponding change in the induced voltage as a result of the alteration in the alternating electromagnetic field at that location. Changes in the voltage provide an indication of the position and motion of valve internals.

Eissenberg, David M. (Oak Ridge, TN); Haynes, Howard D. (Knoxville, TN); Casada, Donald A. (Knoxville, TN)

1993-01-01T23:59:59.000Z

75

Lost-motion valve actuator  

SciTech Connect

A lost-motion valve actuator is described for a bore closure valve employed in a well bore, comprising: operating connector means adapted to move the bore closure valve between open and closed positions through longitudinal movement of the operating connector means. The operating connector means comprises an operating connector and a connector insert defining a recess therebetween; locking dog means comprising at least one locking dog received in the recess and spring biasing means adapted to urge at least one locking dog radially inwardly; and mandrel means slidably received within the operating connector means and including dog slot means associated therewith. The dog slot means comprises an annular slot on the exterior of the mandrel means adapted to lockingly receive at least one inwardly biased locking dog when proximate thereto, whereby longitudinal movement of the mandrel means is transmitted to the operating connector means.

Burris, W.J. III; Ringgenberg, P.D.

1987-04-07T23:59:59.000Z

76

Valve for controlling flow of cryogenic fluid  

DOE Patents (OSTI)

A valve is provided for accurately controlling the flow of cryogenic fluids such as liquid nitrogen. The valve comprises a combination of disc and needle valves affixed to a valve stem in such a manner that the disc and needle are free to rotate about the stem, but are constrained in lateral and vertical movements. This arrangement provides accurate and precise fluid flow control and positive fluid isolation.

Knapp, P.A.

1995-12-31T23:59:59.000Z

77

Experiences and Attributes of Successful Valve Teams  

Science Conference Proceedings (OSTI)

Recently, a number of utilities have found that an effective approach to improve valve performance and reliability is to develop specialized cross-disciplinary teams that have the responsibility for a specific valve or valve types throughout the plant or utility. This report describes the composition, size, and functions of the different types of valve teams studied and provides a myriad of success stories and lessons learned regarding their employment throughout the nuclear power industry.

2000-12-20T23:59:59.000Z

78

TWO-WAY FREEZE VALVE  

DOE Patents (OSTI)

A valve for closing off the flow of radioactive and corrosive gases and liquids or mixtures thereof and forming a leak tight barrier is described. This valve has no mechanical moving parts which would require design to close tolerances and retention of the usual seal tighthess. Instead, there is provided a cavity in which a fusible metal is contained. Heating and cooling are provided to exercise control over the state of the metal. Baffle chambers are utilized to separate the molten fusible metal from the gas or liquid which is being passed through and return the molten metal to its cavity.

Lantz, K.D.; Clark, P.M.

1960-01-01T23:59:59.000Z

79

Valve for fuel pin loading system  

DOE Patents (OSTI)

A cyclone valve surrounds a wall opening through which cladding is projected. An axial valve inlet surrounds the cladding. Air is drawn through the inlet by a cyclone stream within the valve. An inflatable seal is included to physically engage a fuel pin subassembly during loading of fuel pellets.

Christiansen, D.W.

1984-01-01T23:59:59.000Z

80

Valve test program: response to TMI  

Science Conference Proceedings (OSTI)

The Electric Power Research Institute (EPRI) pressurized-water reactor (PWR) safety and relief valve test program was speedily organized to assess valve operability after a pressurizer relief valve malfunctioned at Three Mile Island (TMI). Comprehensive full-scale testing at several facilities validated the basic designs in use today. 2 figures.

Lihach, N.; Bilanin, W.; Carey, J.

1983-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Valve for fuel pin loading system  

DOE Patents (OSTI)

A cyclone valve surrounds a wall opening through which cladding is projected. An axial valve inlet surrounds the cladding. Air is drawn through the inlet by a cyclone stream within the valve. An inflatable seal is included to physically engage a fuel pin subassembly during loading of fuel pellets.

Christiansen, David W. (Kennewick, WA)

1985-01-01T23:59:59.000Z

82

Flow Characteristics Analysis of Widows' Creek Type Control Valve for Steam Turbine Control  

Science Conference Proceedings (OSTI)

The steam turbine converts the kinetic energy of steam to mechanical energy of rotor blades in the power conversion system of fossil and nuclear power plants. The electric output from the generator of which the rotor is coupled with that of the steam turbine depends on the rotation velocity of the steam turbine bucket. The rotation velocity is proportional to the mass flow rate of steam entering the steam turbine through valves and nozzles. Thus, it is very important to control the steam mass flow rate for the load following operation of power plants. Among various valves that control the steam turbine, the control valve is most significant. The steam flow rate is determined by the area formed by the stem disk and the seat of the control valve. While the ideal control valve linearly controls the steam mass flow rate with its stem lift, the real control valve has various flow characteristic curves pursuant to the stem lift type. Thus, flow characteristic curves are needed to precisely design the control valves manufactured for the operating conditions of nuclear power plants. OMEGA (Optimized Multidimensional Experiment Geometric Apparatus) was built to experimentally study the flow characteristics of steam flowing inside the control valve. The Widows' Creek type control valve was selected for reference. Air was selected as the working fluid in the OMEGA loop to exclude the condensation effect in this simplified approach. Flow characteristic curves were plotted by calculating the ratio of the measured mass flow rate versus the theoretical mass flow rate of the air. The flow characteristic curves are expected to be utilized to accurately design and operate the control valve for fossil as well as nuclear plants. (authors)

Yoo, Yong H.; Sohn, Myoung S.; Suh, Kune Y. [PHILOSOPHIA, Inc., Seoul National University, San 56-1 Sillim-dong, Gwanak-gu, Seoul, 151-742 (Korea, Republic of)

2006-07-01T23:59:59.000Z

83

Hydraulic servo control spool valve  

DOE Patents (OSTI)

A servo operated spool valve having a fixed sleeve and axially movable spool. The sleeve is machined in two halves to form a long, narrow tapered orifice slot across which a transverse wall of the spool is positioned. The axial position of the spool wall along the slot regulates the open orifice area with extreme precision.

Miller, Donald M. (Sunnyside, WA)

1983-01-01T23:59:59.000Z

84

Valve assembly for inflatable packer  

Science Conference Proceedings (OSTI)

This patent describes a valve assembly for controlling the flow of fluid from within casing into a bladder element of an inflatable packer for use in a wellbore. The bladder element has bladder port means. The valve assembly is mountable within a single cavity in a body member in the wall of casing or a casing coupling. The body member has casing port means communicating with the cavity for communicating casing fluid to the bladder port means so that the casing fluid can flow through the bladder port means to inflate the bladder element and the body member having overpressure port means communicating with the cavity for communicating part of the fluid flowing into the bladder element back to the cavity and to the valve assembly. The valve assembly comprises: control piston means movably mounted within the cavity, restraint means for insuring that the control piston means initially moves only when the pressure of the casing fluid reaches a predetermined level, and closing piston means movably mounted within the cavity and responsive to the pressure of the fluid in the bladder element, and the control piston means and the closing piston movable about stem means disposed in the cavity.

Stringfellow, W.D.

1987-12-08T23:59:59.000Z

85

Valve Application, Maintenance, and Repair Guide  

Science Conference Proceedings (OSTI)

The Valve Application, Maintenance, and Repair Guide is a two-volume series that provides a generic overview of valve application, selection, maintenance, and repair. Volume 1 of the series is a comprehensive reference on the application and use of valves that provides guidance on the selection of specific types of valves on the basis of functional and system requirements. This document is based on an earlier EPRI document (NP-6516, Guide for the Application and Use of Valves in Power Plant Systems). Ext...

1999-05-07T23:59:59.000Z

86

Change-over valve for air suspension  

Science Conference Proceedings (OSTI)

A change-over valve is described for an air suspension interposed between a main air chamber formed to surround a shock absorber provided with a piston rod and an auxiliary air chamber, comprising: a valve base having a first hole through which the piston rod extends and a second hole into which a valve body is inserted; the valve body disposed in the second hole; a holder disposed in the second hole; and means removably fixed to the piston rod extending through the first hole to connect the piston rod with the valve base while preventing the holder from falling out.

Buma, S.

1987-04-28T23:59:59.000Z

87

A LARGE BAKEABLE VACUUM VALVE  

SciTech Connect

The development and design of a large bakeable valve based on a unique seat arrangement and a novel motion seal are described. The seat sealing is accomplished through the use of high pressure fluid actuation of an annular pinch gasket. Experimental data on seat closure performance, and the specific design features to achieve successful closures, are presented. The bakeable motion seal utilizes a stainless steel bellows sleeving over an inner concentric actuating shaft. This shaft is bent at 90 deg to the axis of rotation and is free to rotate relative to the bellows. There is no apparent size limitation to this type of actuation. The design of a 10-inch gate valve utilizing these principles is described. (auth)

Batzer, T.H.

1959-08-01T23:59:59.000Z

88

Fail Save Shut Off Valve for Filtering Systems Employing Candle Filters  

NLE Websites -- All DOE Office Websites (Extended Search)

Fail Save Shut Off Fail Save Shut Off Valve for Filtering Systems Employing Candle Filters Opportunity The Department of Energy's National Energy Technology Laboratory (NETL) is seeking licensing partners interested in implementing United States Patent Number 6,981,516 entitled "Fail save shut off valve for filtering systems employing candle filters." Disclosed in this patent is a novel fail save shut off valve system that allows fluid flow during normal operational conditions, but prevents the flow of fluids in the event of system failure upstream that causes over- pressurization. It is particularly well suited for use in conjunction with hot gas filtering systems, which utilize ceramic candle filters. Used in such a hot gas system, the fail save valve stops the flow

89

International Steam Turbine Valve Metallurgy Guide  

Science Conference Proceedings (OSTI)

This report reviews the state of the art in materials usage for steam turbine valves manufactured and used in Europe and looks at materials options for the higher-temperature applications now being considered for advanced high-efficiency power plants. The emphasis is on valves for extreme service conditions (high temperatures, pressures, and flow rates), of which bypass valves represent a good example. Some consideration is also given to degradation and failure mechanisms. In focusing on practices outsid...

2011-09-27T23:59:59.000Z

90

Propellant actuated nuclear reactor steam depressurization valve  

DOE Patents (OSTI)

A nuclear fission reactor combined with a propellant actuated depressurization and/or water injection valve is disclosed. The depressurization valve releases pressure from a water cooled, steam producing nuclear reactor when required to insure the safety of the reactor. Depressurization of the reactor pressure vessel enables gravity feeding of supplementary coolant water through the water injection valve to the reactor pressure vessel to prevent damage to the fuel core.

Ehrke, Alan C. (San Jose, CA); Knepp, John B. (San Jose, CA); Skoda, George I. (Santa Clara, CA)

1992-01-01T23:59:59.000Z

91

Improved valve and dash-pot assembly  

DOE Patents (OSTI)

A dash-pot valve comprises a cylinder submerged in the fluid of a housing and have a piston attached to a plunger projecting into the path of closing movement of a pivotal valve member. A vortex chamber in said cylinder is provided with targentially directed inlets to generate vortex flow upon retraction of said plunger and effect increasing resistance against said piston to progressively retard the closing rate of said valve member toward its seat.

Chang, S.C.

1985-04-23T23:59:59.000Z

92

Valve and dash-pot assembly  

DOE Patents (OSTI)

A dash-pot valve comprising a cylinder submerged in the fluid of a housing and having a piston attached to a plunger projecting into the path of closing movement of a pivotal valve member. A vortex chamber in said cylinder is provided with tangentially directed inlets to generate vortex flow upon retraction of said plunger and effect increasing resistance against said piston to progressively retard the closing rate of said valve member toward its seat.

Chang, Shih-Chih (Richland, WA)

1986-01-01T23:59:59.000Z

93

IMPROVEMENTS IN OR RELATING TO VALVED DUCTING  

SciTech Connect

A coaxial valved ducting is designed for fluid flow to and from a heat exchanger. The ducting comprises an inner pipe for flow of hot fluid, an outer pipe providing an annular passage for the countercurrent flow of cool fluid, a butterfly valve in the inner pipe, peripherally spaced longitudinal ribs joining the two pipes in the region of the valve, an extension of the outer pipe, and a butterfly or poppet valve associated with the extension. the inner pipe communicates with the heat exchanger by means of an extension through the outer pipe wall. (D.L.C.)

Blackburn, G.; Long, E.

1962-05-30T23:59:59.000Z

94

All-metal valve structure for gas systems  

DOE Patents (OSTI)

A valve assembly with a resilient metal seat member is disclosed for providing a gas-tight seal in a gas handling system. The valve assembly also includes a valve element for sealing against the valve seat member; and an actuating means for operating the valve element. The valve seat member is a one-piece stainless steel ring having a central valve port and peripheral mounting flange, and an annular corrugation in between. A groove between the first and second ridges serves as a flexure zone during operation of the valve member and thus provides the seating pressure between the inner ridge or valve seat and the valve element. The outer annular ridge has a diameter less than said valve element to limit the seating motion of the valve element, preventing non-elastic deformation of the seat member.

Baker, R.W.; Pawlak, D.A.; Ramey, A.J.

1982-06-10T23:59:59.000Z

95

Hydraulic engine valve actuation system including independent feedback control  

DOE Patents (OSTI)

A hydraulic valve actuation assembly may include a housing, a piston, a supply control valve, a closing control valve, and an opening control valve. The housing may define a first fluid chamber, a second fluid chamber, and a third fluid chamber. The piston may be axially secured to an engine valve and located within the first, second and third fluid chambers. The supply control valve may control a hydraulic fluid supply to the piston. The closing control valve may be located between the supply control valve and the second fluid chamber and may control fluid flow from the second fluid chamber to the supply control valve. The opening control valve may be located between the supply control valve and the second fluid chamber and may control fluid flow from the supply control valve to the second fluid chamber.

Marriott, Craig D

2013-06-04T23:59:59.000Z

96

Giant magnetoresistance in ion beam deposited spin-valve films with specular enhancement  

Science Conference Proceedings (OSTI)

Three different techniques, natural oxidation, remote plasma oxidation and low energy ion beam oxidation, have been proved to be equally effective in forming nano-oxide layers (NOLs) in spin-valve films for specular enhancement of giant magnetoresistance (GMR) effect. GMR values over 12% have been routinely obtained in spin-valve films with NOL, corresponding to a 30% specular enhancement over those without NOL. The consistency and robustness of the oxidation processes has been demonstrated by a very large GMR value {similar_to}19% in a dual spin-valve film with the NOLs formed in both pinned layers, the oscillatory dependence of the interlayer coupling field on Cu layer thickness in specular enhanced spin-valve films and the uniform and repeatable film performance over 5 in. substrates. {copyright} 2001 American Institute of Physics.

Sant, S.; Mao, M.; Kools, J.; Koi, K.; Iwasaki, H.; Sahashi, M.

2001-06-01T23:59:59.000Z

97

Method and apparatus for monitoring motor operated valve motor ...  

A method and apparatus are provided for monitoring a motor operated valve during the brief period when the valve seats and the torque switch trips to deenergize the ...

98

High precision high flow range control valve  

DOE Patents (OSTI)

A fluid control valve is described having a valve housing having first and second valve housing openings for the ingress and egress of fluid through the control valve. Disposed within a void formed by the control valve is a sleeve having at least one sleeve opening to permit the flow of fluid therethrough. A flow restricter travels within the sleeve to progressively block off the sleeve opening and thereby control flow. A fluid passageway is formed between the first valve housing opening and the outer surface of the sleeve. A second fluid passageway is formed between the inside of the sleeve and the second valve housing opening. Neither fluid passageway contains more than one 90.degree. turn. In the preferred embodiment only one of the two fluid passageways contains a 90.degree. turn. In another embodiment, the control valve housing is bifurcated by a control surface having control surface opening disposed therethrough. A flow restricter is in slidable contact with the control surface to restrict flow of fluid through the control surface openings.

McCray, John A. (Idaho Falls, ID)

1999-01-01T23:59:59.000Z

99

Vertical pump with free floating check valve  

DOE Patents (OSTI)

A vertical pump with a bottom discharge having a free floating check valve isposed in the outlet plenum thereof. The free floating check valve comprises a spherical member with a hemispherical cage-like member attached thereto which is capable of allowing forward or reverse flow under appropriate conditions while preventing reverse flow under inappropriate conditions.

Lindsay, Malcolm (O' Hara Township, Allegheny County, PA)

1980-01-01T23:59:59.000Z

100

Replace Pressure-Reducing Valves with Backpressure Turbogenerators: Office of Industrial Technologies (OIT) Steam Tip Fact Sheet No. 20  

SciTech Connect

Many industrial facilities produce steam at a higher pressure than is demanded by process requirements. Steam passes through pressure-reducing valves (PRVs, also known as letdown valves) at various locations in the steam distribution system to let down or reduce its pressure. A non-condensing or backpressure steam turbine can perform the same pressure-reducing function as a PRV, while converting steam energy into electrical energy.

2002-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Scoping Study on the Safety Impact of Valve Spacing in Natural Gas Pipelines  

Science Conference Proceedings (OSTI)

The U.S. Department of Transportation's Pipeline and Hazardous Materials Safety Administration (PHMSA) is responsible for ensuring the safe, reliable, and environmentally sound operation of the nation's natural gas and hazardous liquid pipelines. Regulations adopted by PHMSA for gas pipelines are provided in 49 CFR 192, and spacing requirements for valves in gas transmission pipelines are presented in 49 CFR 192.179. The present report describes the findings of a scoping study conducted by Oak Ridge National Laboratory (ORNL) to assist PHMSA in assessing the safety impact of system valve spacing. Calculations of the pressures, temperatures, and flow velocities during a set of representative pipe depressurization transients were carried out using a one-dimensional numerical model with either ideal gas or real gas properties for the fluid. With both ideal gas and real gas properties, the high-consequence area radius for any resulting fire as defined by Stevens in GRI-00/0189 was evaluated as one measure of the pipeline safety. In the real gas case, a model for convective heat transfer from the pipe wall is included to assess the potential for shut-off valve failures due to excessively low temperatures resulting from depressurization cooling of the pipe. A discussion is also provided of some additional factors by which system valve spacing could affect overall pipeline safety. The following conclusions can be drawn from this work: (1) Using an adaptation of the Stephens hazard radius criteria, valve spacing has a negligible influence on natural gas pipeline safety for the pipeline diameter, pressure range, and valve spacings considered in this study. (2) Over the first 30 s of the transient, pipeline pressure has a far greater effect on the hazard radius calculated with the Stephens criteria than any variations in the transient flow decay profile and the average discharge rate. (3) Other factors besides the Stephens criteria, such as the longer burn time for an accidental fire, greater period of danger to emergency personnel, increased unavoidable loss of gas, and possible depressurization cooling of the shut-off valves may also be important when deciding whether a change in the required valve spacing would be beneficial from a safety standpoint. (4) The average normalized discharge rate of {lambda}{sub avg} = 0.33 assumed by Stephens in developing his safety criteria is an excellent conservative value for natural gas discharge at the pressures, valve spacings, and pipe diameter used in this study. This conclusion remains valid even when real rather than ideal gas properties are considered in the analysis. (5) Significant pipe wall cooling effects (T{sub w} pipeline rupture accident.

Sulfredge, Charles David [ORNL

2007-07-01T23:59:59.000Z

102

Federal Energy Management Program: Covered Product Category:...  

NLE Websites -- All DOE Office Websites (Extended Search)

Covered Product Category: Pre-Rinse Spray Valves to someone by E-mail Share Federal Energy Management Program: Covered Product Category: Pre-Rinse Spray Valves on Facebook Tweet...

103

Subsurface safety valves: safety asset or safety liability  

SciTech Connect

This paper summarizes the methods used to compare the risk of a blowout for a well completed with a subsurface safety valve (SSSV) vs. a completion without an SSSV. These methods, which could be applied to any field, include a combination of SSSV reliability and conventional risk analyses. The Kuparuk River Unit Working Interest Owners recently formed a group to examine the risks associated with installing and maintaining SSSV's in the Kuparuk field. The group was charged with answering the question: ''Assuming Kuparuk field operating conditions, are SSSV's a safety asset, or do numerous operating and maintenance procedures make them a safety liability.'' The results indicate that for the Kuparuk River Unit, an SSSV becomes a safety liability when the mean time between SSSV failures is less than one year. Since current SSSV mean time to failure (MTTF) at Kuparuk is approximately 1000 days, they are considered a safety asset.

Busch, J.M.; Llewelyn, D.C.G.; Policky, B.J.

1983-10-01T23:59:59.000Z

104

Valve for controlling solids flow  

DOE Patents (OSTI)

A valve for controlling the flow of solids comprises a vessel having an overflow point, an inlet line for discharging solids into the vessel positioned within the vessel such that the inlet line's discharge point is lower than the vessel's overflow point, and apparatus for introducing a fluidizing fluid into the vessel. The fluidizing fluid fluidizes the solids within the vessel so that they overflow at the vessel's overflow point. For the removal of nuclear waste product the vessel may be placed within a sealed container having a bottom connected transport line for transporting the solids to storage or other sites. The rate of solids flow is controlled by the flow rate of the fluidizing fluid and by V-notch weirs of different sizes spaced about the top of the vessel.

Staiger, M. Daniel (Idaho Falls, ID)

1985-01-01T23:59:59.000Z

105

DISCHARGE VALVE FOR GRANULAR MATERIAL  

DOE Patents (OSTI)

A gravity-red dispenser or valve is designed for discharging the fueled spherical elements used in a pebble bed reactor. The dispenser consists of an axially movable tube terminating under a hood having side walls with openings. When the tube is moved so that its top edge is above the tops of the side openings the elements will not flow. As the tube is moved downwardly, the elements flow into the hood through the side openings and over the top edge into the tube at an increasing rate as the tube is lowered further. The tube is spaced at all times from the hood and side walls a distance greater than the diameter of the largest element to prevent damaging of the elements when the dispenser is closed to flow. (AEC)

Stoughton, L.D.; Robinson, S.T.

1962-05-15T23:59:59.000Z

106

Engine Valve Actuation For Combustion Enhancement  

DOE Patents (OSTI)

A combustion chamber valve, such as an intake valve or an exhaust valve, is briefly opened during the compression and/or power strokes of a 4-stroke combustion cycle in an internal combustion engine (in particular, a diesel or CI engine). The brief opening may (1) enhance mixing withing the combustion chamber, allowing more complete oxidation of particulates to decrease engine emissions; and/or may (2) delay ignition until a more desirable time, potentially allowing a means of timing ignition in otherwise difficult-to-control conditions, e.g., in HCCI (Homogeneous Charge Compression Ignition) conditions.

Reitz, Rolf Deneys (Madison, WI); Rutland, Christopher J. (Madison, WI); Jhavar, Rahul (Madison, WI)

2004-05-18T23:59:59.000Z

107

Engine valve actuation for combustion enhancement  

DOE Patents (OSTI)

A combustion chamber valve, such as an intake valve or an exhaust valve, is briefly opened during the compression and/or power strokes of a 4-strokes combustion cycle in an internal combustion engine (in particular, a diesel or CI engine). The brief opening may (1) enhance mixing withing the combustion chamber, allowing more complete oxidation of particulates to decrease engine emissions; and/or may (2) delay ignition until a more desirable time, potentially allowing a means of timing ignition in otherwise difficult-to-control conditions, e.g., in HCCI (Homogeneous Charge Compression Ignition) conditions.

Reitz, Rolf Deneys (Madison, WI); Rutland, Christopher J. (Madison, WI); Jhavar, Rahul (Madison, WI)

2008-03-04T23:59:59.000Z

108

Method and apparatus for monitoring motor operated valve motor output torque and power at valve seating  

DOE Patents (OSTI)

A method and apparatus are provided for monitoring a motor operated valve during the brief period when the valve seats and the torque switch trips to deenergize the valve motor. The method uses voltage measurements on the load side of a deenergizing switch that opens to deenergize the motor to determine, among other things, final motor rotational speed and the decelerating torque at motor deenergization.

Casada, Donald A. (Oak Ridge, TN)

1996-01-01T23:59:59.000Z

109

Method and apparatus for monitoring motor operated valve motor output torque and power at valve seating  

DOE Patents (OSTI)

A method and apparatus are provided for monitoring a motor operated valve during the brief period when the valve seats and the torque switch trips to deenergize the valve motor. The method uses voltage measurements on the load side of a deenergizing switch that opens to deenergize the motor to determine, among other things, final motor rotational speed and the decelerating torque at motor deenergization. 14 figs.

Casada, D.A.

1996-01-16T23:59:59.000Z

110

Engineering Technical Training Modules - Throttle Valves 1.0  

Science Conference Proceedings (OSTI)

The purpose of this training module is to provide an understanding of specifying throttle valves in a nuclear power plant. The module provides the student with an understanding of the different types of throttle valves, how to select a throttle valve, understand the flow characteristics of different throttle valves, and understanding negative characteristics that can occur when the wrong valve is chosen for different applications. Prior to using this module, the student should understand the fundamental...

2011-06-29T23:59:59.000Z

111

EPRI-Marshall Electric Motor-Operated Valve (Block Valve) Interim Test Data Report  

Science Conference Proceedings (OSTI)

At the request of participating PWR utilities, an overall program was developed at EPRI for the full-scale testing of a representative set of primary-system safety and relief valves. The program was to assist the PWR utilities in meeting NUREG 0737, Item II.D.1.A requirements. Although not a formal part of the program, some block valve operability data were also obtained during the relief valve testing performed at Marshall Steam Station in Terrell, North Carolina. A total of seven block valve designs we...

1982-07-01T23:59:59.000Z

112

Valve studies: Hydrogen fluoride monitoring of UF{sub 6} cylinder valves  

Science Conference Proceedings (OSTI)

Uranium hexafluoride (UF{sub 6}) cylinder valves have, like the cylinders, been in use and/or storage for periods ranging from 15 to 44 years. Visual inspection of the cylinders has shown that the extent of corrosion and the overall cylinder condition varies widely throughout the storage yards. One area of concern is the integrity of the cylinder valves. Visual inspection has found deposits which have been identified as radioactive material on or near the valves. These deposits suggest leakage of UF{sub 6} and may indicate valve degradation; however, these deposits may simply be residual material from cylinder filling operations.

Leedy, R.R.; Ellis, A.R.; Hoffmann, D.P.; Marsh, G.C. [and others

1996-08-01T23:59:59.000Z

113

Method for valve seating control for an electro-hydraulic engine valve  

DOE Patents (OSTI)

Valve lift in an internal combustion engine is controlled by an electro-hydraulic actuation mechanism including a selectively actuable hydraulic feedback circuit.

Sun, Zongxuan (Plymouth, MN)

2011-01-11T23:59:59.000Z

114

Frostless heat pump having thermal expansion valves  

DOE Patents (OSTI)

A heat pump system having an operable relationship for transferring heat between an exterior atmosphere and an interior atmosphere via a fluid refrigerant and further having a compressor, an interior heat exchanger, an exterior heat exchanger, a heat pump reversing valve, an accumulator, a thermal expansion valve having a remote sensing bulb disposed in heat transferable contact with the refrigerant piping section between said accumulator and said reversing valve, an outdoor temperature sensor, and a first means for heating said remote sensing bulb in response to said outdoor temperature sensor thereby opening said thermal expansion valve to raise suction pressure in order to mitigate defrosting of said exterior heat exchanger wherein said heat pump continues to operate in a heating mode.

Chen, Fang C [Knoxville, TN; Mei, Viung C [Oak Ridge, TN

2002-10-22T23:59:59.000Z

115

Install Removable Insulation on Valves and Fittings  

Science Conference Proceedings (OSTI)

This revised ITP tip sheet on installing removable insulation on valves and fittings provides how-to advice for improving the system using low-cost, proven practices and technologies.

Not Available

2006-01-01T23:59:59.000Z

116

Valve Application, Maintenance, and Repair Guide: In Situ State-of-the-Art Valve Welding Repair (Gate, Globe, & Check Valves), Volum e 2  

Science Conference Proceedings (OSTI)

The Valve Application, Maintenance and Repair Guide is a three volume series that provides a generic overview of valve application selection, maintenance, and repair. Volume 2 of this series is a comprehensive guide for in situ weld repair of gate, globe, and check valve components such as bodies, bonnets, discs, and seats. The information in this guide, though directed toward nuclear plant personnel, will assist all power plant engineers, planners, and maintenance personnel responsible for valve mainten...

1996-12-31T23:59:59.000Z

117

Diffusion bonding resistant valve development for sodium service  

SciTech Connect

Unanticipated functional failures occurred in valves undergoing containment integrity testing for liquid sodium service. The failures resulted from diffusion bonding of the Stellite 6B valve plug to the Type 316 stainless steel (SS) seat. As a result of these failures, a valve development program was undertaken. A modified valve incorporating a Tribaloy 800 plug showed significant improvement in resistance to diffusion bonding but still failed after long term exposure in a closed position. A second modified valve using Tribaloy 800 in both the valve plug and seat successfully resisted diffusion bonding failure. This paper reports the details of the testing and posttest valve examinations. The results of scanning electron microscopy, dispersive x-ray spectrometry, and metallography provide the characteristics of the valve failures. Limitations of the various valve designs are also discussed.

Crandall, D.L.; Low, J.O.; Chung, D.T.; Loop, R.B.

1984-04-16T23:59:59.000Z

118

Subsea production test valve assembly  

SciTech Connect

In the subsea test assembly securable within a blowout preventer stack above a subterranean well and positionable between upper and lower portions of a tubular conduit in fluid communication with a production zone within the well, the test assembly is described including an upper subassembly carriable with the upper conduit portion, a lower subassembly carriable with the lower conduit portion, and valve means in the lower subassembly manipulatable between opened and closed positions to control fluid flow within the conduit. The improvement comprises: the upper subassembly including an upper housing and first rigid dog means fixedly secured to the upper housing; the lower subassembly including a lower housing and second rigid dog means fixedly secured to the lower housing; the first rigid dog means positionable between a latch position for latching the upper and lower subassemblies and an unlatch position for unlatching the upper and lower subassemblies upon rotational movement of the first dog means with respect to the second dog means; and lock means axially movable relative to the first and second dog means from a lock position for limiting rotational movement of the first dog means with respect to the second dog means to an unlock position for allowing the first dog means to rotate relative to the second dog means and unlatch the upper subassembly from the lower subassembly.

Yates, P.D.

1988-03-22T23:59:59.000Z

119

Federal Energy Management Program: Federal Procurement of Energy...  

NLE Websites -- All DOE Office Websites (Extended Search)

Energy Management Program (FEMP) is updating the cost calculators for commercial boilers and pre-rinse spray valves. Thank you all for casting your votes at...

120

Analysis on Modulation Principle of Mechanical Spring Valve Block-Type Pulse Jet  

Science Conference Proceedings (OSTI)

To take full advantage of the bottom-hole hydraulic energy to improve the drilling rate, it is proposed the technique assumption that using mechanical spring valve periodically is to block the fluid pathway, and modulating pulse jet is to increase the ... Keywords: block type, pulse jet, drilling rate, water hammer, experimental study

Ni Hongjian; Zhu Lihong; Huo Hongjun; Tang Zhiwen

2011-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Design of a Thermally-Actuated Gas Lift Safety Valve  

E-Print Network (OSTI)

Gas-lifted oil wells are susceptible to failure through malfunction of gas lift valve assemblies (GLV). One failure mode occurs when the GLV check valve fails and product passes into the well annulus, potentially reaching ...

Gilbertson, Eric W.

122

Miniature Fluid Control Valve - Oak Ridge National Laboratory  

Summary: Technology Description A very small control valve that is used to control flow into and out of a finger prosthesis. The valve makes use of a spring loaded poppet

123

Parametric time?frequency estimation of prosthetic heart valve sounds  

Science Conference Proceedings (OSTI)

Prosthetic heart valves have been responsible for extending the life spans and improving the quality of life of many people with serious heart conditions. Even though the heart valves are extremely reliable

D. E. Perkins; G. H. Thomas; G. A. Clark

1998-01-01T23:59:59.000Z

124

Improve safety with pilot operated relief valves  

Science Conference Proceedings (OSTI)

A weakness inherent in balanced bellows pressure relief valves (PRVs) that can cause premature failure can be avoided by using pilot operated PRVs as an alternative. Now better able to handle adverse service conditions, pilot operated PRVs are suitable for a wide range of gas, liquid and mixed-phase services. Traditionally, however, balanced bellows PRVs have been applied as overpressure protection for three notable reasons: a constant PRV set pressure with the presence of variable, superimposed back pressure (at the PRV outlet prior to its opening); valve stability and adequate capacity when built-up back pressure (at the PRV outlet during its relief cycle) exceeds 10%; and spring and guided parts barriered from the process fluid. With these benefits in mind, balanced bellows PRVs have been generally adapted by many hydrocarbon processing companies that have experienced costly, and often dangerous, premature bellows failures. Corrosion, valve instability and/or bellows flutter are causes of these failures.

Emerson, G. [Anderson, Greenwood and Co., Stafford, TX (United States)

1996-10-01T23:59:59.000Z

125

Exhaust gas bypass valve control for thermoelectric generator  

DOE Patents (OSTI)

A method of controlling engine exhaust flow through at least one of an exhaust bypass and a thermoelectric device via a bypass valve is provided. The method includes: determining a mass flow of exhaust exiting an engine; determining a desired exhaust pressure based on the mass flow of exhaust; comparing the desired exhaust pressure to a determined exhaust pressure; and determining a bypass valve control value based on the comparing, wherein the bypass valve control value is used to control the bypass valve.

Reynolds, Michael G; Yang, Jihui; Meisner, Greogry P.; Stabler, Francis R.; De Bock, Hendrik Pieter (Peter) Jacobus; Anderson, Todd Alan

2012-09-04T23:59:59.000Z

126

Worcester Solenoid Actuated Gas Operated MCO Isolation Valves  

SciTech Connect

These valves are 1 inch gas-operated full-port ball valves incorporating a solenoid and limit switches as Integral parts of the actuator that are used in different process streams within the CVDF hood. The valves fail closed (on loss of pressure or electrical) for MCO isolation to either reduce air in leakage or loss of He. All valves have coupling for transverse actuator mounting.

VAN KATWIJK, C.

2000-06-06T23:59:59.000Z

127

Worchester Solenoid Actuated Gas Operated MCO Isolation Valves  

Science Conference Proceedings (OSTI)

These valves are 1 inch gas-operated full-port ball valves incorporating a solenoid and limit switches as integral parts of the actuator that are used in process streams within the CWF hood. The valves fail closed (on loss of pressure or electrical) to prevent MCO vent drain to either reduce air In-leakage or loss of He. The valves have couplings for transverse actuator mounting.

MISKA, C.R.

2000-11-13T23:59:59.000Z

128

Worcester Solenoid Actuated Gas Operated MCO Isolation Valves  

Science Conference Proceedings (OSTI)

These valves are 1 inch gas-operated full-port ball valves incorporating a solenoid and limit switches as integral parts of the actuator that are used in different process streams within the CVDF hood. The valves fail closed (on loss of pressure or electrical) for MCO isolation to either reduce air leakage or loss of He. All valves have coupling for transverse actuator mounting.

MISKA, C.R.

2000-11-13T23:59:59.000Z

129

Worcester Solenoid Actuated Gas Operated MCO Isolation Valves  

Science Conference Proceedings (OSTI)

These valves are 1 inch gas-operated full-port ball valves incorporating a solenoid and limit switches as integral parts of the actuator that are used in different process streams within the CVDF hood. The valves fail closed (on loss of pressure or electrical) for MCO isolation to either reduce air in leakage or loss of He. All valves have coupling for transverse actuator mounting.

MISKA, C.R.

2000-09-03T23:59:59.000Z

130

Worchester Solenoid Actuated Gas Operated MCO Isolation Valves  

SciTech Connect

These valves are 1 inch gas-operated full-port ball valves incorporating a solenoid and limit switches as integral parts of the actuator that are used in process streams within the CVDF hood. The valves fail closed (on loss of pressure or electrical) to prevent MCO vent drain to either reduce air in-leakage or loss of He. The valves have couplings for transverse actuator mounting.

VAN KATWIJK, C.

2000-06-06T23:59:59.000Z

131

Acoustic classification of the state of artificial heart valves  

Science Conference Proceedings (OSTI)

Transthoracic acoustic signals from BSCC (Björk–Shiley convexo–concave) mechanical heart valves implanted in human patients were processed to determine if the valves had separated outflow struts. For normal valves with intact outflow struts it is demonstrated that a time?windowed spectral analysis reveals the resonant frequency of the vibrating strut. The strut

Terry D. Plemons; Michael Hovenga

1995-01-01T23:59:59.000Z

132

Disc valve for sampling erosive process streams  

DOE Patents (OSTI)

This is a patent for a disc-type, four-port sampling valve for service with erosive high temperature process streams. Inserts and liners of ..cap alpha..-silicon carbide respectively, in the faceplates and in the sampling cavities, limit erosion while providing lubricity for a smooth and precise operation. 1 fig.

Mrochek, J.E.; Dinsmore, S.R.; Chandler, E.W.

1984-08-16T23:59:59.000Z

133

Separators for valve regulated lead acid batteries  

Science Conference Proceedings (OSTI)

This paper reviews some aspects of the past history of the valve regulated lead acid (VRLA) battery in relationship to microglass separators that have been used from the conception of VRLA technology. It also focuses on some aspects of compression properties of the separator.

Zguris, G.C. [Hollingsworth & Vose Co., West Groton, MT (United States)

1995-01-01T23:59:59.000Z

134

Hydraulically actuated gas exchange valve assembly and engine using same  

DOE Patents (OSTI)

An engine comprises a housing that defines a hollow piston cavity that is separated from a gas passage by a valve seat. The housing further defines a biasing hydraulic cavity and a control hydraulic cavity. A gas valve member is also included in the engine and is movable relative to the valve seat between an open position at which the hollow piston cavity is open to the gas passage and a closed position in which the hollow piston cavity is blocked from the gas passage. The gas valve member includes a ring mounted on a valve piece and a retainer positioned between the ring and the valve piece. A closing hydraulic surface is included on the gas valve member and is exposed to liquid pressure in the biasing hydraulic cavity.

Carroll, Thomas S. (Peoria, IL); Taylor, Gregory O. (Hinsdale, IL)

2002-09-03T23:59:59.000Z

135

Technical evaluation: 300 Area steam line valve accident  

SciTech Connect

On June 7, 1993, a journeyman power operator (JPO) was severely burned and later died as a result of the failure of a 6-in. valve that occurred when he attempted to open main steam supply (MSS) valve MSS-25 in the U-3 valve pit. The pit is located northwest of Building 331 in the 300 Area of the Hanford Site. Figure 1-1 shows a layout of the 300 Area steam piping system including the U-3 steam valve pit. Figure 1-2 shows a cutaway view of the approximately 10- by 13- by 16-ft-high valve pit with its various steam valves and connecting piping. Valve MSS-25, an 8-in. valve, is located at the bottom of the pit. The failed 6-in. valve was located at the top of the pit where it branched from the upper portion of the 8-in. line at the 8- by 8- by 6-in. tee and was then ``blanked off`` with a blind flange. The purpose of this technical evaluation was to determine the cause of the accident that led to the failure of the 6-in. valve. The probable cause for the 6-in. valve failure was determined by visual, nondestructive, and destructive examination of the failed valve and by metallurgical analysis of the fractured region of the valve. The cause of the accident was ultimately identified by correlating the observed failure mode to the most probable physical phenomenon. Thermal-hydraulic analyses, component stress analyses, and tests were performed to verify that the probable physical phenomenon could be reasonably expected to produce the failure in the valve that was observed.

Not Available

1993-08-01T23:59:59.000Z

136

A rotary-airlock valve resists abrasive mixtures  

SciTech Connect

Hill and Griffith (H and G, Cincinnati, Ohio) is a leading supplier of custom-blended additives to founderies. Thousands of tons of clay and carbon blends such as bentonite, gilsonite and pulverized coal, pass through the company's rotary-airlock feeding system each month. H and G's original rotary valves had cylinders lined with chrome, and closed-end rotors with tips made from nickel-chromium alloys. These valves remained in service for a maximum of only three months each. During that time, the abrasive mixtures passing through the valves virtually eroded them, increasing tolerances and causing significant air leakage. The leaks caused the pneumatic line to plug up, reducing the velocity of the line below the minimum level needed to carry any material. To overcome the leakage, a second blower was added to the system. This unit supplied an additional 40 brake hp to the pneumatic-conveying line. With constant maintenance of the valve and the continuous operation of both blowers, H and G was able to extend the valve's life by nine months. After 20 years of trying valves with various configuration, H and G installed a Smoot Type 6 rotary-airlock valve in September of 1985. The new valve's internals were made from abrasion-resistant grades of NiHard and Stellite. This combination of alloys prolonged the active life of the valve by improving its abrasion resistance. During its first year, the Smoot valve did not break down, leak air or require use of the secondary blower. After its first year of service no wear was found on the valve's internal surfaces. Another mechanical analysis was performed in 1991, after five additional years of valve operation. The valve, which had now handled more than 250,000 tons of product, showed minimal wear. H and G's capital costs had been reduced from 25[cents]/ton to 3[cents]/ton by the new valve.

Not Available

1993-03-01T23:59:59.000Z

137

Blooming Prairie Public Utilities - Commercial & Industrial Energy...  

Open Energy Info (EERE)

150 - 400 Dishwashers: 300 - 1,000 Ventilation Hood Controllers: 165HP Low-Flow Spray Valve: 50% of installed cost Equipment Requirements Appliances must be Energy Star...

138

Endurance tests of valves with cobalt-free hardfacing alloys: PWR phase  

SciTech Connect

Atomic Energy of Canada Limited (AECL) is conducting endurance tests on valves hard-faced with four cobalt-free alloys. The first phase of the program, in which PWR primary heat transport conditions were simulated in AECL's valve test loop, has been completed. The candidate alloys are NOREM 01, NOREM 04, EB 5183 and EVERIT 50. One valve with Stellite 6 trim served as the standard. Prior to loop testing, a baseline inaugural inspection was performed. During testing the loop was shutdown at approximately 500 cycle intervals, and the valves were disassembled for examination. The examinations included seat leak tests, profilometry, nondestructive inspection and finally destructive examination. Corrosion coupons in the loop were used to monitor any material loss due solely to corrosion mechanisms. This report summarizes the final examination results and discusses the relative performance of the candidate alloys. The results indicate that, based upon the sliding wear damage assessment and seat leakage test results, all the candidate alloys perform better than the Stellite 6 control sample. On the same basis, NOREM 04 and EB 5183 are the best of the candidate alloys, although there are only minor differences in performance among the four alloys.

Murphy, E.V.; Inglis, I. (Atomic Energy of Canada Ltd., Mississauga, ON (Canada))

1992-05-01T23:59:59.000Z

139

Water cooling of HVDC thyristor valves  

SciTech Connect

It is generally accepted that water is a very effective medium to remove heat losses from any type of equipment. When used for HVDC thyristor valves, the fundamentals of electrolyte conduction and water chemistry need to be considered in the design of the cooling circuit. The characteristics of the materials used, in conjunction with high voltage stresses and circuit configuration, play an important role to assure longevity and corrosion-free performance.

Lips, H.P. (Siemens AG, Erlangen (Germany))

1994-10-01T23:59:59.000Z

140

The operation of LPG relief valves  

SciTech Connect

As stipulated by NFPA 58, all LPG storage containers must be equipped with one or more pressure relief devices. These devices are sized to prevent rupture of a normally charged container when exposed to fire. This paper describes in detail the functioning of the spring-loaded relief valve. The author discusses how the venting of LPGs can produce unacceptable risks and how training is a necessary part of controlling such a situation.

Stannard, J.H. Jr

1989-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Platelet thrombosis in cardiac-valve prostheses  

SciTech Connect

The contribution of platelets and clotting factors in thrombosis on cardiovascular prostheses had been quantified with several tracers. Thrombus formation in vivo could be measured semiquantitatively in animal models and patients with indium-111, Technetium-99m labeled platelets, iodine-123, iodine-131 labeled fibrinogen, and In-111 and Tc-99m labeled antibody to the fibrinogen-receptor on the platelet- membrane, or fibrin. The early studies demonstrated that certain platelet-inhibitors, e.g. sulfinpyrazone, aspirin or aspirin- persantine increased platelet survival time with mechanical valves implanted in the baboon model and patients. Thrombus localization by imaging is possible for large thrombus on thrombogenic surface of prosthesis in the acute phase. The majority of thrombus was found in the sewing ring (Dacron) in the acute phase in both the mechanical and tissue valves. The amount of retained thrombus in both mechanical and tissue valves in our one-day study in the dog model was similar (< 1% if injected In-111 platelets = 5 billion platelets). As the fibrous ingrowth covered the sewing ring, the thrombus formation decreased significantly. Only a small amount of thrombus was found on the leaflets at one month in both the dog and calf models. 38 refs., 9 figs., 5 tabs.

Dewanjee, M.K.

1989-01-01T23:59:59.000Z

142

Method and system for measuring gate valve clearances and seating force  

DOE Patents (OSTI)

Valve clearances and seating force, as well as other valve operational parameters, are determined by measuring valve stem rotation during opening and closing operations of a translatable gate valve. The magnitude of the stem rotation, and the relative difference between the stem rotation on opening and closing provides valuable data on the valve internals in a non-intrusive manner.

Casada, Donald A. (Knoxville, TN); Haynes, Howard D. (Knoxville, TN); Moyers, John C. (Oak Ridge, TN); Stewart, Brian K. (Burns, TN)

1996-01-01T23:59:59.000Z

143

ANALYSIS OF CHECK VALVE DISC MOTION DURING A FLOW TRANSIENT  

SciTech Connect

An analysis of the dynamics of a check valve disc under the influence of a flow transient is presented. The impact velocities of the disc and the pressure surge resulting from extinguishing a fluid velocity are predicted. This analysis develops the equations of motion of a simple swing disc check valve from Newton's Second Law. Modifications of the analysis necessary for application to other types of valves are described. The developed equations are progiammed for the Philco-2000 digital computer in FORTRAN as the SLAM Code. The Code input consists of the characteristics of the valve and the flow transient. The output of the code includes the dynamics of the valve disc as a function of time and the pressure surge induced by valve closure. (H.G.G.)

Fuls, G.M.

1962-12-01T23:59:59.000Z

144

Determination of Earths transient and equilibrium climate sensitivities from observations over the twentieth century: Strong dependence on assumed forcing  

Science Conference Proceedings (OSTI)

Relations among observed changes in global mean surface temperature, ocean heat content, ocean heating rate, and calculated radiative forcing, all as a function of time over the twentieth century, that are based on a two-compartment energy balance model, are used to determine key properties of Earth's climate system. The increase in heat content of the world ocean, obtained as the average of several recent compilations, is found to be linearly related to the increase in global temperature over the period 1965-2009; the slope, augmented to account for additional heat sinks, which is an effective heat capacity of the climate system, is 21.8 {+-} 2.1 W year m{sup -2} K{sup -1} (one sigma), equivalent to the heat capacity of 170 m of seawater (for the entire planet) or 240 m for the world ocean. The rate of planetary heat uptake, determined from the time derivative of ocean heat content, is found to be proportional to the increase in global temperature relative to the beginning of the twentieth century with proportionality coefficient 1.05 {+-} 0.06 W m{sup -2} K{sup -1}. Transient and equilibrium climate sensitivities were evaluated for six published data sets of forcing mainly by incremental greenhouse gases and aerosols over the twentieth century as calculated by radiation transfer models; these forcings ranged from 1.1 to 2.1 W m{sup -2}, spanning much of the range encompassed by the 2007 assessment of the Intergovernmental Panel on Climate Change (IPCC). For five of the six forcing data sets, a rather robust linear proportionality obtains between the observed increase in global temperature and the forcing, allowing transient sensitivity to be determined as the slope. Equilibrium sensitivities determined by two methods that account for the rate of planetary heat uptake range from 0.31 {+-} 0.02 to 1.32 {+-} 0.31 K (W m{sup -2}){sup -1} (CO{sub 2} doubling temperature 1.16 {+-} 0.09-4.9 {+-} 1.2 K), more than spanning the IPCC estimated 'likely' uncertainty range, and strongly anticorrelated with the forcing used to determine the sensitivities. Transient sensitivities, relevant to climate change on the multidecadal time scale, are considerably lower, 0.23 {+-} 0.01 to 0.51 {+-} 0.04 K (W m{sup -2}){sup -1}. The time constant characterizing the response of the upper ocean compartment of the climate system to perturbations is estimated as about 5 years, in broad agreement with other recent estimates, and much shorter than the time constant for thermal equilibration of the deep ocean, about 500 years.

Schwartz S. E.

2012-05-04T23:59:59.000Z

145

U.S. Steam Turbine Valve Actuator Condition Assessment  

Science Conference Proceedings (OSTI)

This report provides nuclear and fossil plant personnel with current information on the inspection and assessment of steam turbine valve actuators.

2008-12-23T23:59:59.000Z

146

DEVELOPMENT OF FREEZE VALVE FOR USE IN THE MSRE  

SciTech Connect

Three types of frozen-seal valves'' were tested for possible use in the MSRE. The seal was melted by direct resistance heat, by induction heat, and by clamp-on Calrod heat. The frozen seal was made in a preformed restriction section of a standard piece of pipe by a cooling-gas jet stream directed at the restriction. All three valves performed satisfactorily through 100 test cycles. The Calrodheated valve was selected for MSRE use on the basis of simplicity of design and of operation. Two of the valves are successfully undergoing further tests on the MSRE Engineering Test Loop. (auth)

Richardson, M.

1962-02-28T23:59:59.000Z

147

U.S. Steam Turbine Valve Metallurgy Guide  

Science Conference Proceedings (OSTI)

This report provides nuclear and fossil plant personnel with current information on the metallurgical aspects of the steam turbine valve components used in U.S. power plants.

2009-03-30T23:59:59.000Z

148

Computer Based Training: Check Valves 1.0  

Science Conference Proceedings (OSTI)

ETTM Check Valves is a computer based training module that allows users to access training when desired and review it at their own pace. It provides graphics and limited interactive features to enhance learning. The purpose of this module is to provide the user with a basis for selecting and sizing a check valve for nuclear station applications. While more than one valve type can be used for most applications, the intent is to point out the differences between check valve designs and to assist the user i...

2010-10-07T23:59:59.000Z

149

Meso-fluidic Control Valve - Oak Ridge National Laboratory  

Volume Systems Advantages: Small Size ... Meso-fluidic Control Valve-1974 Contact: Mark Reeves Oak Ridge National Laboratory P.O. Box 2008, Mail Stop ...

150

Electric actuation of a surface controlled subsea safety valve  

E-Print Network (OSTI)

The growing technology associated with petroleum equipment has lead to an increase in electrical components used to measure, adjust and control many aspects of the petroleum extraction process. This increase in electrical use has lead to the conversion of many components from hydraulic operation to electric. Therefore, it is the purpose of this report to detail and propose an engineering solution to the electrical conversion of a surface controlled subsea safety valve (SCSSV). Preliminary analysis has resulted in the following important functional requirements that the SCSSV should operate within: Temperatures up to 350 F. Estimated operational life of 20 years. Peak available power of 4300 W (actual value will be much lower than this due to other power system drains). The three conceptual designs presented in this report are the following: Electric motor actuator with a solenoid latching detent. Linear actuation with a fluid reservoir locking valve. Rotational engagement with an electric locking clutch. After reviewing and comparing these concepts, the last concept was chosen to be further developed. This concept will have the least temperature sensitive components and fewer leak path problem areas. Upon completion of the detailed design phase an electric SCSSV solution has been proposed. The following is a brief list of the performance claims: Power requirement to open: 0.5 W. Time required to open valve: 10 minutes. Installable inline with 4-1/2 tubing. Operating temperature range: 20-350 F. H?S service certified. Hold open energy requirements 0~0.2 W. There are however practical issues that must be addressed to ensure reliable and satisfactory performance of the SCSSV. The actual efficiency of the cylindrical cam mechanism and reliability of the torque overload clutch must be empirically determined due to the number of theoretical assumptions used. Thus these items should be thoroughly tested in order to produce a reliable and satisfactory SCSSV. It is with these claims and working issue that this electrically converted SCSSV be fully developed and installed for electrical petroleum production systems.

Bartlett, Timothy Joseph

2002-01-01T23:59:59.000Z

151

Numerical Investigation of the Performance of Three Hinge Designs of Bileaflet Mechanical Heart Valves  

E-Print Network (OSTI)

parameters on bilea?et mechanical heart valve ?ow dynamics.J. Heart Valve Dis. 18:535–545, 2009. Gross, J. M. , M. C.two bilea?et mechanical heart valves under aortic and mitral

Simon, Hélčne A.; Ge, Liang; Sotiropoulos, Fotis; Yoganathan, Ajit P.

2010-01-01T23:59:59.000Z

152

Stem control of a sliding-stem pneumatic control valve using a recurrent neural network  

Science Conference Proceedings (OSTI)

This paper presents a neural scheme for controlling an actuator of pneumatic control valve system. Bondgraph method has been used to model the actuator of control valve, in order to compare the response characteristics of valve. The proposed controller ...

Mohammad Heidari, Hadi Homaei

2013-01-01T23:59:59.000Z

153

Simulation of a novel electromechanical engine valve drive to quantify performance gains in fuel consumption  

E-Print Network (OSTI)

This thesis describes the modeling and simulation of a novel electromechanical valve drive known as the MIT EMV. This valve drive allows an engine to achieve variable valve timing which has been shown to produce improvements ...

Miller, Justin (Justin Lee)

2011-01-01T23:59:59.000Z

154

EPRI/C-E PWR Safety Valve Test Report Volume 3: Test Results for Dresser Safety Valve Model 31739A  

Science Conference Proceedings (OSTI)

EPRI at the request of the PWR utilities developed an overall program for the testing of PWR primary system safety and relief valves. This program was in response to NUREG 0578 Item 2.1.2 and NUREG 0737 Item II.D.1.A requirements. This report documents the results of safety valve testing performed as part of the overall program at the EPRI/C-E Valve Test Facility located at Combustion Engineering's Kreisinger Development Laboratory, Windsor, Connecticut. Seven safety valves representative of those utiliz...

1983-02-01T23:59:59.000Z

155

Selling Random Energy  

E-Print Network (OSTI)

generation in short term energy markets,” IEEE Trans. Powerentity into a forward energy market. For my Family, Tony,into a forward energy market. Assuming that coalitional

Bitar, Eilyan Yamen

2011-01-01T23:59:59.000Z

156

Nuclear-radiation-actuated valve. [Patent application; for increasing coolant flow to blanket  

DOE Patents (OSTI)

The present invention relates to a breeder reactor blanket fuel assembly coolant system valve which increases coolant flow to the blanket fuel assembly to minimize long-term temperature increases caused by fission of fissile fuel created from fertile fuel through operation of the breeder reactor. The valve has a valve first part (such as a valve rod with piston) and a valve second part (such as a valve tube surrounding the valve rod, with the valve tube having side slots surrounding the piston). Both valve parts have known nuclear radiation swelling characteristics. The valve's first part is positioned to receive nuclear radiation from the nuclear reactor's fuel region. The valve's second part is positioned so that its nuclear radiation induced swelling is different from that of the valve's first part. The valve's second part also is positioned so that the valve's first and second parts create a valve orifice which changes in size due to the different nuclear radiation caused swelling of the valve's first part compared to the valve's second part. The valve may be used in a nuclear reactor's core coolant system.

Christiansen, D.W.; Schively, D.P.

1982-01-19T23:59:59.000Z

157

Giant magnetoresistance in organic spin valves  

SciTech Connect

Interfacial diffusion between magnetic electrodes and organic spacer layers is a serious problem in the organic spintronics which complicates attempts to understand the spin-dependent transport mechanism and hurts the achievement of a desirably high magnetoresistance (MR). We deposit nanodots instead of atoms onto the organic layer using buffer layer assist growth. Spin valves using this method exhibit a sharper interface and a giant MR of up to {approx}300%. Analysis of the current-voltage characteristics indicates that the spin-dependent carrier injection correlates with the observed MR.

Sun, Da-Li [ORNL; Yin, Lifeng [ORNL; Sun, Chengjun [ORNL; Guo, Hangwen [ORNL; Gai, Zheng [ORNL; Zhang, Xiaoguang [ORNL; Ward, Thomas Z [ORNL; Cheng, Zhaohua [Chinese Academy of Sciences; Shen, Jian [ORNL

2010-01-01T23:59:59.000Z

158

Closed Loop Test Facility for hot dirty gas valves  

SciTech Connect

A design study of a closed loop test facility for eight-inch hot dirty gas valves is presented. The objective of the facility is to quality valves for use in coal gasifiers, combined cycle plants, and pressurized fluid bed combustors. Outline sketches and estimated costs are presented for the selected design.

Not Available

1980-02-06T23:59:59.000Z

159

Classification of prosthetic heart valve sounds: A parametric approach  

Science Conference Proceedings (OSTI)

People with heart problems have had their lives extended considerably with the development of the prosthetic heart valve. Great strides have been made in the development of the valves through the use of improved materials as well as efficient mechanical designs. However

J. V. Candy; H. E. Jones

1995-01-01T23:59:59.000Z

160

Cam-driven valve system for steam turbines  

SciTech Connect

This patent describes, in a steam turbine system including a source of motive steam and a turbine adapted to operate at less than a full load, the turbine including an improved cam-driven valve system for activating a varying number of steam control valves to permit transferring between a maximum arc-admission mode and a minimum arc-admission mode. It comprises: a steam chest for receiving the motive steam from the source, the steam chest including a plurality of valves connected to a corresponding turbine section and set for a minimum admission of motive steam into the turbine below 100 percent; a first cam lift means for actuating a portion of the valves and second cam lift means for actuating the remainder of the valves.

Silvestri, G.J. Jr.

1990-02-27T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Post-Remedial Action Report the Chapman Valve Site E I P I I  

Office of Legacy Management (LM)

for for Post-Remedial Action Report the Chapman Valve Site E I P I I I t I 1 I I I 1 I li I I Pnnted on recycledkecyclable paper 24 19 0186 1 DOE/OW21949-408 Formerly Utilized Sites Remed Contr: al Action Program (FUSRAP) L C t NO. DE-AC05-91 OR21 949 Indian Orchard, assac h.usetts November 1996 DOE/OR/2 1949-408 POST-REMEDIAL ACTION REPORT FOR THE CHAPMAN VALVE SITE INDIAN ORCHARD, MASSACHUSETTS NOVEMBER 1996 Prepared for United States Department of Energy Oak Ridge Operations Office Under Contract No. DE-AC05-91 OR2 1949 Bechtel National, Inc. Oak Ridge, Tennessee . . Bechtel Job No. 14501 CONTENTS Page . FIGURES ................................................................................... 1 .............................................................. iv

162

Technical and economic analysis of energy efficiency of Chinese room air conditioners  

E-Print Network (OSTI)

the impact on national energy consumption by adoption of thecase forecast of national energy consumption assumes thatcase forecast of national energy consumption assumes the

Fridley, David G.; Rosenquist, Gregory; Jiang, Lin; Li, Aixian; Xin, Dingguo; Cheng, Jianhong

2001-01-01T23:59:59.000Z

163

Analysis of Long-range Clean Energy Investment Scenarios for Eritrea, East Africa  

E-Print Network (OSTI)

to utilizing excellent wind energy resources as a driver toSubsector Efficiency, (5) Wind Energy Development, and (6)assumed return rate. For wind energy development, we assume

Van Buskirk, Robert D.

2004-01-01T23:59:59.000Z

164

Wireless connection instructions -Windows This document outlines the procedure for setting up Windows7, Vista or XP to use the College wireless network. It assumes  

E-Print Network (OSTI)

Wireless connection instructions - Windows This document outlines the procedure for setting up Windows7, Vista or XP to use the College wireless network. It assumes that you have already connected your Wireless Networks window Registering your computer Start your web browser, ie. Internet Explorer Your

Goldschmidt, Christina

165

Internal combustion engine with rotary valve assembly having variable intake valve timing  

DOE Patents (OSTI)

An internal combustion engine has rotary valves associated with movable shutters operable to vary the closing of intake air/fuel port sections to obtain peak volumetric efficiency over the entire range of speed of the engine. The shutters are moved automatically by a control mechanism that is responsive to the RPM of the engine. A foot-operated lever associated with the control mechanism is also used to move the shutters between their open and closed positions.

Hansen, Craig N. (Eden Prairie, MN); Cross, Paul C. (Shorewood, MN)

1995-01-01T23:59:59.000Z

166

Engine valve and method of producing the same  

SciTech Connect

An engine valve of an internal combustion engine is described which consists of: a hollow tube member formed of a drawn steel tube, the hollow tube member having a central portion comprising a tubular body, and a first end part which is flared outwardly and includes an open end peripheral portion at the extreme end of the first end part, the hollow tube member tubular body constituting a valve stem section; a generally disc-shaped lid member made of metal and having a peripheral portion integrally connected with the open end peripheral portion of the hollow tube member, the lid member and the first end part of the hollow tube member constituting a valve head section; and a stem end member made of metal and integrally connected with a second part of the hollow tube member; a filler metal comprising stellite disposed in contact with the open end peripheral portion of the hollow tube member first end part and the peripheral portion of the disc-shaped lid member to secure together the hollow tube member and the lid member to thereby form the integral connection, the stellite filler metal being a wear and corrosion resistant nonferrous alloy, the filler metal being formed as a padding having a peripheral surface including a valve face for contacting a valve seat of an engine; and a filling comprising an aluminum alloy containing silicon, the filling being disposed in the valve head section to fill the valve head section.

Hayashi, Y.

1986-07-01T23:59:59.000Z

167

Analysis of a Third-Generation Princeton Tri-leaflet Mechanical Heart Valve  

E-Print Network (OSTI)

Analysis of a Third-Generation Princeton Tri-leaflet Mechanical Heart Valve Michael Hsu Advisor heart valve · Static analysis of leaflet under uniform pressure of 10 MPa Summer Objectives · Find Heart valve disease · Over 5 million affected · Over 225,000 valve- replacement surgeries performed

Petta, Jason

168

Control system for the turbomolecular pumping stations and sector valves of the CERN Intersecting Storage Rings  

E-Print Network (OSTI)

Control system for the turbomolecular pumping stations and sector valves of the CERN Intersecting Storage Rings

Gröbner, Oswald

1971-01-01T23:59:59.000Z

169

Noninvasive valve monitor using constant magnetic and/or DC electromagnetic field  

DOE Patents (OSTI)

One or more sources of steady magnetic field are carefully located on the outside of a valve body. The constant magnetic field is transmitted into the valve body and valve internals. A magnetic field detector carefully located on the outside of the valve body detects the intensity of the magnetic field at its location. As the position of a valve internal part is changed, there is an alteration in the magnetic field in the valve, and a consequent change in the detected magnetic field. Changes in the detected signal provide an indication of the position and motion of the valve internals.

Casada, D.A.; Haynes, H.D.

1993-08-17T23:59:59.000Z

170

Noninvasive valve monitor using constant magnetic and/or DC electromagnetic field  

SciTech Connect

One or more sources of steady magnetic field are carefully located on the outside of a valve body. The constant magnetic field is transmitted into the valve body and valve internals. A magnetic field detector carefully located on the outside of the valve body detects the intensity of the magnetic field at its location. As the position of a valve internal part is changed, there is an alteration in the magnetic field in the valve, and a consequent change in the detected magnetic field. Changes in the detected signal provide an indication of the position and motion of the valve internals.

Casada, Donald A. (Knoxville, TN); Haynes, Howard D. (Knoxville, TN)

1993-01-01T23:59:59.000Z

171

Analog and digital control of an electronic throttle valve  

E-Print Network (OSTI)

Two electronic throttler controllers were designed and implemented for an automotive throttle valve on a four-cylinder, spark-ignition gasoline engine. The first controller was designed using operational amplifiers and ...

Martins, Tomás V

2012-01-01T23:59:59.000Z

172

Replace Pressure-Reducing Valves with Backpressure Turbogenerators  

SciTech Connect

This revised ITP steam tip sheet on replacing pressure-reducing valves provides how-to advice for improving industrial steam systems using low-cost, proven practices and technologies.

Not Available

2006-01-01T23:59:59.000Z

173

Technical Repair Guide for Rotork Valve Actuators "NA" Range Models  

Science Conference Proceedings (OSTI)

This guide provides comprehensive technical information on Rotork valve actuator operation, maintenance, testing, and troubleshooting. Its design provides the user with a uniform methodology to reduce human errors and increase actuator reliability.

1995-12-31T23:59:59.000Z

174

Efforts by the nuclear industry to evaluate check valve failures  

SciTech Connect

Recent studies identified approximately 4000 check valve failures that occurred from 1984-1991. Of these, approximately 1600 were determined to be significant enough to require further analysis. This is to be compared with the existing check valve population of nearly 21,000 valves. The strategy proposed in this paper is to establish a refined, centralized check valve failure/reliability database based in part on existing Institute of Nuclear Power Operations (INPO) Nuclear Plant Reliability Data System (NPRDS) data. Ideally the database would be maintained in a central location, augmented with specific component information, overall reliability information, and updated at least biannually. The data would be available to sort and search as desired. The conceptual plan is provided and possible uses of the database are given.

Hart, K.; McElhaney, K.L.; Casada, D.A.

1994-12-31T23:59:59.000Z

175

Failure Mode and Sensitivity Analysis of Gas Lift Valves  

E-Print Network (OSTI)

Gas-lifted oil wells are susceptible to failure through malfunction of gas lift valves. This is a growing concern as offshore wells are drilled thousands of meters below the ocean floor in extreme temperature and pressure ...

Gilbertson, Eric W.

176

Nonlinear springs with applications to flow regulation valves and mechanisms  

E-Print Network (OSTI)

This thesis focuses on the application of nonlinear springs for fluid flow control valves where geometric constraints, or fabrication technologies, limit the use of available solutions. Types of existing nonlinear springs ...

Freeman, David Calvin

2008-01-01T23:59:59.000Z

177

Design of an electronically-actuated gas lift safety valve  

E-Print Network (OSTI)

Gas lift valves are widely used in oil production fields to pump recycled gas and nitrogen into the production tubing, to sustain production by aerating the oil and lifting it to the ground or sea surface. Today's industry ...

Yu, Changkuan, S.M. Massachusetts Institute of Technology

2013-01-01T23:59:59.000Z

178

Steam Turbine Casing and Valve Body Repair Guidelines  

Science Conference Proceedings (OSTI)

Today’s flexible mode of operation can result in damage to heavy-section components, such as steam turbine and valve casings. Thus, owners and operators are often faced with repairing a critical component. This report is part of a set of documents that address the key areas in the asset management of steam turbine casings and valve bodies—nondestructive evaluation and damage detection, repair, and life ...

2013-12-14T23:59:59.000Z

179

Worcester 1 Inch Solenoid Actuated Gas Operated SCHe System Valves  

SciTech Connect

1 inch gas-operated full-port ball valves incorporate a solenoid and limit switches as integral parts of the actuator. These valves are normally open and fail safe to the open position (GOV-1*02 and 1*06 fail closed) to provide a flow path of helium gas to the MCO under helium purge and off-normal conditions when the MCO is isolated.

MISKA, C.R.

2000-09-03T23:59:59.000Z

180

Worcester 1 Inch Solenoid Actuated Gas Operated SCHe System Valves  

SciTech Connect

1 inch Gas-operated full-port ball valves incorporate a solenoid and limit switches as integral parts of the actuator. These valves are normally open and fail safe to the open position (GOV-1*02 and 1*06 fall closed) to provide a flow path of helium gas to the MCO under helium purge and off-normal conditions when the MCO is isolated.

VAN KATWIJK, C.

2000-10-23T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Worcester 1 Inch Solenoid Actuated Gas Operated SCHe System Valves  

SciTech Connect

1 inch gas-operated full-port ball valves incorporate a solenoid and limit switches as integral parts of the actuator. These valves are normally open and fail safe to the open position (GOV-1*02 and 1*06 fail closed) to provide a flow path of helium gas to the MCO under helium purge and off-normal conditions when the MCO is isolated.

MISKA, C.R.

2000-11-13T23:59:59.000Z

182

Worcester 1 Inch Solenoid Actuated Gas Operated SCHe System Valves  

SciTech Connect

1 inch Gas-operated full-port ball valves incorporate a solenoid and limit switches as integral parts of the actuator. These valves are normally open and fail safe to the open position (GOV-1*02 and 1*06 fail closed) to provide a flow path of helium gas to the MCO under helium purge and off-normal conditions when the MCO is isolated.

VAN KATWIJK, C.

2000-06-06T23:59:59.000Z

183

Valving for controlling a fluid-driven reciprocating apparatus  

DOE Patents (OSTI)

A pair of control valve assemblies for alternately actuating a pair of fluid-driven free-piston devices by using fluid pressure communication therebetween. Each control valve assembly is switched by a pressure signal depending on the state of its counterpart's piston. The communication logic is arranged to provide overlap of the forward strokes of the pistons, so that at least one of the pair will always be pressurized. Thus, uninterrupted pumping of liquid is made possible from a pair of free-piston pumps. In addition, the speed and frequency of piston stroking is entirely dependent on the mechanical power load applied. In the case of a pair of pumps, this enables liquid delivery at a substantially constant pressure over the full range of flow rates, from zero to maximum flow. Each of the valve assemblies uses an intake-exhaust valve and a signal valve with the signal valve of one pump being connected to be pressure responsive to the piston of the opposite cylinder or pump.

Whitehead, John C. (Davis, CA)

1995-01-01T23:59:59.000Z

184

Gas lift valve failure mode analysis and the design of a thermally-actuated positive-locking safety valve  

E-Print Network (OSTI)

Gas-lifted oil wells are susceptible to failure through malfunction of gas lift valves. This is a growing concern as offshore wells are drilled thousands of meters below the ocean floor in extreme temperature and pressure ...

Gilbertson, Eric (Eric W.)

2010-01-01T23:59:59.000Z

185

Engine including hydraulically actuated valvetrain and method of valve overlap control  

DOE Patents (OSTI)

An exhaust valve control method may include displacing an exhaust valve in communication with the combustion chamber of an engine to an open position using a hydraulic exhaust valve actuation system and returning the exhaust valve to a closed position using the hydraulic exhaust valve actuation assembly. During closing, the exhaust valve may be displaced for a first duration from the open position to an intermediate closing position at a first velocity by operating the hydraulic exhaust valve actuation assembly in a first mode. The exhaust valve may be displaced for a second duration greater than the first duration from the intermediate closing position to a fully closed position at a second velocity at least eighty percent less than the first velocity by operating the hydraulic exhaust valve actuation assembly in a second mode.

Cowgill, Joel (White Lake, MI)

2012-05-08T23:59:59.000Z

186

Monovalve with integrated fuel injector and port control valve, and engine using same  

DOE Patents (OSTI)

An engine includes an engine casing that defines a hollow piston cavity separated from an exhaust passage and an intake passage by a valve seat. A gas exchange valve member is positioned adjacent the valve seat and is moveable between an open position and a closed position. The gas exchange valve member also defines an opening that opens into the hollow piston cavity. A needle valve member is positioned in the gas exchange valve member adjacent a nozzle outlet and is moveable between an inject position and a blocked position. A port control valve member, which has a hydraulic surface, is mounted around the gas exchange valve member and moveable between an intake position and an exhaust position. A pilot valve is moveable between a first position at which the port control hydraulic surface is exposed to a source of high pressure fluid, and a second position at which the port control hydraulic surface is exposed to a source of low pressure fluid.

Milam, David M. (Metamora, IL)

2001-11-06T23:59:59.000Z

187

Design and Testing of Vacuum Breaker Check Valve for Simplified Boiling Water Reactor  

Science Conference Proceedings (OSTI)

A new design of the vacuum breaker check valve was developed to replace the mechanical valve in a simplified boiling water reactor. Scaling and design calculations were performed to obtain the geometry of new passive hydraulic vacuum breaker check valve. In order to check the valve performance, a RELAP5 model of the simplified boiling water reactor system with the new valve was developed. The valve was implemented in an integral facility, PUMA and was tested for large break loss of coolant accident. (authors)

Ishii, M.; Xu, Y.; Revankar, S.T. [Purdue University, West Lafayette, IN 47907 (United States)

2002-07-01T23:59:59.000Z

188

Design and fabrication of microfluidic valves using poly(N-isopropylacrylamide)  

E-Print Network (OSTI)

A compact printable microfluidic valve composed of poly(N-isopropylacrylamide) has been designed, fabricated, and tested. The design of the valve consists of filling microwells with poly(NIPAAm) and bonding PDMS channels ...

Reticker-Flynn, Nathan Edward

2008-01-01T23:59:59.000Z

189

Processing of prosthetic heart valve sounds for single leg separation classification  

Science Conference Proceedings (OSTI)

People with serious heart conditions have had their expected life span extended considerably with the development of the prosthetic heart valve especially with the great strides made in valve design. Even though the designs are extremely reliable

J. V. Candy; H. E. Jones

1995-01-01T23:59:59.000Z

190

Drive piston assembly for a valve actuator assembly  

DOE Patents (OSTI)

A drive piston assembly is provided that is operable to selectively open a poppet valve. The drive piston assembly includes a cartridge defining a generally stepped bore. A drive piston is movable within the generally stepped bore and a boost sleeve is coaxially disposed with respect to the drive piston. A main fluid chamber is at least partially defined by the generally stepped bore, drive piston, and boost sleeve. First and second feedback chambers are at least partially defined by the drive piston and each are disposed at opposite ends of the drive piston. At least one of the drive piston and the boost sleeve is sufficiently configured to move within the generally stepped bore in response to fluid pressure within the main fluid chamber to selectively open the poppet valve. A valve actuator assembly and engine are also provided incorporating the disclosed drive piston assembly.

Sun, Zongxuan (Troy, MI)

2010-02-23T23:59:59.000Z

191

Technical Repair Guidelines for the Limitorque Model SMB-00 Valve Actuator  

Science Conference Proceedings (OSTI)

This technical repair guideline (TRG) is the second in a series of documents devoted to comprehensive maintenance and repair of the motor-operated Limitorque SMB-00 valve actuator. The Limitorque SMB-00 valve actuator is mounted on a nonrotating rising stem valve and is applicable to other types of valves and installation arrangements. This report was written with the latest available information, however, changes to the actuator's design, parts availability, etc. may supersede this document but will not...

1995-06-30T23:59:59.000Z

192

Water Consumption from Freeze Protection Valves for Solar Water Heating Systems  

DOE Green Energy (OSTI)

Conference paper regarding research in the use of freeze protection valves for solar domestic water heating systems in cold climates.

Burch, J.; Salasovich, J.

2005-12-01T23:59:59.000Z

193

Surfacing of the parts of Christmas tree valves  

SciTech Connect

The authors discuss the strengthening of Christmas trees for service conditions, in particular, the method of plasma spraying of the sealing surfaces of the gates of the valves with hard corrosion resistant alloys. Most frequently, cobalt- (stellite), nickel- (colmonoy), and iron-base alloys are used for surfacing. A plan is shown of the area for plasma surfacing in one of the petroleum machinery plants. It is found that the hardening of the sealing surface of gate valve parts by plasma powder surfacing with self-fluxing nickel alloys increases the reliability and life of well-head equipment.

Mordynskii, V.B.; Barsukov, V.P.; Iskakhov, A.R.; Komarcheva, E.S.

1987-07-01T23:59:59.000Z

194

ESTIMATED SIL LEVELS AND RISK COMPARISONS FOR RELIEF VALVES AS A FUNCTION OF TIME-IN-SERVICE  

SciTech Connect

Risk-based inspection methods enable estimation of the probability of spring-operated relief valves failing on demand at the United States Department of Energy's Savannah River Site (SRS) in Aiken, South Carolina. The paper illustrates an approach based on application of the Frechet and Weibull distributions to SRS and Center for Chemical Process Safety (CCPS) Process Equipment Reliability Database (PERD) proof test results. The methodology enables the estimation of ANSI/ISA-84.00.01 Safety Integrity Levels (SILs) as well as the potential change in SIL level due to modification of the maintenance schedule. Current SRS practices are reviewed and recommendations are made for extending inspection intervals. The paper compares risk-based inspection with specific SILs as maintenance intervals are adjusted. Groups of valves are identified in which maintenance times can be extended as well as different groups in which an increased safety margin may be needed.

Harris, S.

2012-03-26T23:59:59.000Z

195

A study on the use of multiple surrogate models in valve design  

Science Conference Proceedings (OSTI)

Nowadays, the use of computational fluid dynamics (CFD) in the design of valves is very common. Despite the continuing growth of computing capability, the computational cost of complex three-dimensional CFD analysis of butterfly valve maintains high, ... Keywords: DOE, butterfly valve, error analysis, multiple surrogate models, optimization

Xue Guan Song; Jeong Ju Choi; Joon-Ho Lee; Young Chul Park

2011-09-01T23:59:59.000Z

196

Probability of Safety Valve Failure-to-Reseat Following Steam and Liquid Relief: Quantitative Expert Elicitation  

Science Conference Proceedings (OSTI)

This report describes a quantitative expert elicitation to assist in the determination of the failure probability of safety valves to reseat following steam and/or liquid relief. The expert elicitation process improves the estimation of the safety valve failure-to-reseat probability and is based on expert judgment, safety valve testing programs, and experience.

2004-08-31T23:59:59.000Z

197

Worcester 1 Inch Solenoid Actuated Gas Operated VPS System Ball Valve  

SciTech Connect

1 inch Gas-operated full-port ball valve incorporates a solenoid and limit switches as integral parts of the actuator. The valve is normally open and fails safe to the closed position. The associated valve position switch is class GS.

VAN KATWIJK, C.

2000-06-06T23:59:59.000Z

198

Worcester 1 Inch Solenoid Actuated Gas Operated VPS System Ball Valve  

Science Conference Proceedings (OSTI)

1 inch Gas-operated full-pod ball valve incorporates a solenoid and limit switches as integral park of the actuator. The valve is normally open and fails safe to the closed position. The associated valve position switch is class GS.

MISKA, C.R.

2000-11-13T23:59:59.000Z

199

Workshop on gate valve pressure locking and thermal binding  

SciTech Connect

The purpose of the Workshop on Gate Valve Pressure Locking and Thermal Binding was to discuss pressure locking and thermal binding issues that could lead to inoperable gate valves in both boiling water and pressurized water reactors. The goal was to foster exchange of information to develop the technical bases to understand the phenomena, identify the components that are susceptible, discuss actual events, discuss the safety significance, and illustrate known corrective actions that can prevent or limit the occurrence of pressure locking or thermal binding. The presentations were structured to cover U.S. Nuclear Regulatory Commission staff evaluation of operating experience and planned regulatory activity; industry discussions of specific events, including foreign experience, and efforts to determine causes and alleviate the affects; and valve vendor experience and recommended corrective action. The discussions indicated that identifying valves susceptible to pressure locking and thermal binding was a complex process involving knowledge of components, systems, and plant operations. The corrective action options are varied and straightforward.

Brown, E.J.

1995-07-01T23:59:59.000Z

200

Sealing of process valves for the HEU downblending verification experiment at Portsmouth  

SciTech Connect

At the Portsmouth Gaseous Diffusion Plant in Piketon, Ohio, USA, excess inventory of highly-enriched uranium (HEU) from US defense programs is being diluted to low-enriched uranium (LEU) for commercial use. The conversion is subject to a Verification Experiment overseen by the International Atomic Energy Agency (IAEA). The Verification Experiment is making use of monitoring technologies developed and installed by several DOE laboratories. One of the measures is a system for sealing valves in the process piping, which secures the path followed by uranium hexafluoride gas (UF{sub 6}) from cylinders at the feed stations to the blend point, where the HEU is diluted with LEU. The Authenticated Item Monitoring System (AIMS) was the alternative proposed by Sandia National Laboratories that was selected by the IAEA. Approximately 30 valves were sealed by the IAEA using AIMS fiber-optic seals (AFOS). The seals employ single-core plastic fiber rated to 125 C to withstand the high-temperature conditions of the heated piping enclosures at Portsmouth. Each AFOS broadcasts authenticated seal status and state-of-health messages via a tamper-protected radio-frequency transmitter mounted outside of the heated enclosure. The messages are received by two collection stations, operated redundantly.

Baldwin, G.T.; Bartberger, J.C.; Jenkins, C.D.; Perlinski, A.W.; Schoeneman, J.L. [Sandia National Labs., Albuquerque, NM (United States); Gordon, D.M. [Brookhaven National Lab., Upton, NY (United States); Whiting, N.E. [International Atomic Energy Agency (IAEA); Bonner, T.N.; Castle, J.M. [Lockheed Martin Utility Services, Piketon, OH (United States). Portsmouth Gaseous Diffusion Plant

1998-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Investigation of a rotary valving system with variable valve timing for internal combustion engines: Final technical report  

DOE Green Energy (OSTI)

The objective of the program was to provide a functional demonstration of the Hansen Rotary Valving System with Variable Valve timing (HRVS/VVT), capable of throttleless inlet charge control, as an alternative to conventional poppet-valves for use in spark ignited internal combustion engines. The goal of this new technology is to secure benefits in fuel economy, broadened torque band, vibration reduction, and overhaul accessibility. Additionally, use of the variable valve timing capability to vary the effective compression ratio is expected to improve multi-fuel tolerance and efficiency. Efforts directed at the design of HRVS components proved to be far more extensive than had been anticipated, ultimately requiring that proof-trial design/development work be performed. Although both time and funds were exhausted before optical or ion-probe types of in-cylinder investigation could be undertaken, a great deal of laboratory data was acquired during the course of the design/development work. This laboratory data is the basis for the information presented in this Final Report.

Cross, P.C.; Hansen, C.N.

1994-11-18T23:59:59.000Z

202

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

51 - 16760 of 28,905 results. 51 - 16760 of 28,905 results. Download TMP: Order (2013-CE-5334) DOE ordered TMP Manufacturing Company, Inc. to pay a $8,000 civil penalty after finding TMP had failed to certify that certain models of walk-in cooler and freezer components comply with the applicable energy conservation standards. http://energy.gov/gc/downloads/tmp-order-2013-ce-5334 Download American Valve: Order (2010-CW-1411) DOE ordered American Valve, Inc. to pay a $5,000 civil penalty after finding American Valve had failed to certify that certain showerhead models comply with the applicable water conservation standards. http://energy.gov/gc/downloads/american-valve-order-2010-cw-1411 Download DuraLamp USA: Order (2010-CE-0912) DOE ordered DuraLamp USA, Inc. to pay a $2,500 civil penalty after finding

203

Application of a Plasma Powder Welding to engine valves  

SciTech Connect

In hardfacing of automobile engine valves made of heat resisting steel such as 21-4N, conventional oxy-acetylene gase welding has been currently conducted manually by well trained operators because of using cast Stellite rods as the filler. In accordance with the strong demands of automatic welding, the authors newly developed an automatically controlled Plasma Powder Welding (PPW) system. This system is characterized by the application of a high thermal density plasma arc as heat source and by using power filler which melts more easily than bar cast rods. Moreover, this PPW system has been applied to the automotive engine valve production line and resulted in the great contribution to manpower saving.

Takeuchi, Y.; Nagata, M.

1985-01-01T23:59:59.000Z

204

DOE-SPEC-3019-96; Valve-Regulated Type Lead-Acid Storage Batteries  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9-96 9-96 August 1996 DOE SPECIFICATION VALVE-REGULATED TYPE LEAD-ACID STORAGE BATTERIES U.S. Department of Energy FSC 6140 Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. This document has been reproduced directly from the best available copy. Available to DOE and DOE contractors from the Office of Scientific and Technical Information, P.O. Box 62, Oak Ridge, TN 37831; (423) 576-8401. Available to the public from the U.S. Department of Commerce, Technology Administration, National Technical Information Service, Springfield, VA 22161; (703) 487-4650. Order No. DE96009470 DOE-SPEC-3019-96 THIS PAGE INTENTIONALLY LEFT BLANK DOE-SPEC-3019-96 iii FOREWORD 1. Use of this purchase specification is not mandatory. User should review the document and

205

Valve Regulated Lead Acid (VRLA) Battery Qualification Assessment  

Science Conference Proceedings (OSTI)

Valve-regulated lead acid (VRLA) batteries have been proposed as a prospective dc power source for Class 1E service in passive nuclear plants. However, they are not currently covered by IEEE Standard 535, which addresses qualification for this service. Furthermore, there are reports of significant failure modes or mechanisms beyond the predominant failure mode of grid corrosion of the positive plate associated with vented lead acid (VLA) batteries.

2009-11-06T23:59:59.000Z

206

Application of Nanocoatings for Erosion Protection of Valve Stems  

Science Conference Proceedings (OSTI)

Damage in steam turbine valve stems is attributed to erosion from the impingement of spalled oxides present in the high-temperature flowing steam environment. Utilities and turbine engineers are currently managing the erosion and damage issues through component replacement (in some extreme cases, with component lives shorter than one year). With limited success, numerous materials have been examined as alternatives to extend component life. Erosion-resistant nanocoatings have shown superior performance t...

2010-12-19T23:59:59.000Z

207

Diffusion based degradation mechanisms in giant magnetoresistive spin valves  

Science Conference Proceedings (OSTI)

Spin valve systems based on the giant magnetoresistive effect as used, for example, in hard disks and automotive applications consist of several functional metallic thin film layers. We have identified by secondary ion mass spectrometry two main degradation mechanisms: one is related to oxygen diffusion through a protective cap layer and the other one is interdiffusion directly at the functional layers of the giant magnetoresistive stack. By choosing a suitable material as cap layer (TaN), the oxidation effect can be suppressed.

Hawraneck, Matthias [Department of Sense and Control, Infineon Technologies AG, 85579 Neubiberg (Germany); Institute for Materials Science, Technische Universitaet Darmstadt, 64287 Darmstadt (Germany); Zimmer, Juergen; Raberg, Wolfgang; Pruegl, Klemens; Schmitt, Stephan; Bever, Thomas [Department of Sense and Control, Infineon Technologies AG, 85579 Neubiberg (Germany); Flege, Stefan; Alff, Lambert [Institute for Materials Science, Technische Universitaet Darmstadt, 64287 Darmstadt (Germany)

2008-07-07T23:59:59.000Z

208

Steam Turbine Valve Actuator Condition Assessment: 2013 Update  

Science Conference Proceedings (OSTI)

This report provides nuclear and fossil plant personnel with current information on the inspection and assessment of steam turbine valve actuators. It covers the actuators that are typically found on the turbines of the two major U.S. original equipment manufacturers (OEMs), as well as those of several non-U.S. OEMs. The scope encompasses both mechanical hydraulic control (MHC) and electronic hydraulic control (EHC) types of hydraulic ...

2013-07-25T23:59:59.000Z

209

Safety and Relief Valve Testing and Maintenance Guide  

Science Conference Proceedings (OSTI)

This guide gives a broad overview of self actuated and power operated pressure relief devices (PRDs) -- safety, relief, safety relief, and power-operated relief valves -- and their application and maintenance. The non-reclosing devices, like the rupture discs, are outside the scope of this guide. The information in this guide, though directed towards the nuclear power plant personnel, will assist all power plant personnel responsible for the maintenance of PRDs. This guide can also be used by training in...

1996-10-02T23:59:59.000Z

210

The lubrication of engine valve trains equipped with ceramicized followers  

Science Conference Proceedings (OSTI)

The valve train wear characteristics of motored 2.2l and 2.3l engines were examined using ceramic and conventional metal cam followers. Under regular wear conditions with fully formulated motor oils, minimal wear was observed on the metal cam lobes running with either the ceramicized or metal followers. Running under chemically accelerated wear conditions with low quality oil, however, cam lobe wear with ceramicized followers was observed to be significantly less than that with metal followers. The difference in wear was diminished when testing high quality oils under chemically accelerated conditions. Typical testing revealed that the metal follower pads quickly developed considerable wear in a characteristic pattern, while the ceramic followers pads quickly developed considerable were in a characteristic pattern, while the ceramic followers exhibited only slight polishing. Scanning electron photographs revealed details of the used ceramic surfaces, and that wear took place by polishing and by intergranular fracture with subsequent material removal. Engine wear is a major factor that limits the life of today's passenger cars. Particularly for the newer models that have smaller but higher speed and output engines incorporating current designs such as overhead camshafts, 4-valves per cylinder and turbochargers, the valve train represents one of the highest wear components within an engine. In light of the trend towards extended drivetrain warranties, there is a strong demand for lubricant suppliers to develop engine oils with improved antiwear performance. In a parallel effort, automotive engine and component manufacturers are enhancing valve train durability with technologies that include roller followers and the use of advanced ceramic materials.

Blahey, A.G.; Habeeb, J.J.; Rogers, W.N.< 110> The lubrication of engine valve trains equipped with ceramicized followers.

1990-01-01T23:59:59.000Z

211

Sliding-gate valve for use with abrasive materials  

DOE Patents (OSTI)

The invention is a flow and pressure-sealing valve for use with abrasive solids. The valve embodies special features which provide for long, reliable operating lifetimes in solids-handling service. The valve includes upper and lower transversely slidable gates, contained in separate chambers. The upper gate provides a solids-flow control function, whereas the lower gate provides a pressure-sealing function. The lower gate is supported by means for (a) lifting that gate into sealing engagement with its seat when the gate is in its open and closed positions and (b) lowering the gate out of contact with its seat to permit abrasion-free transit of the gate between its open and closed positions. When closed, the upper gate isolates the lower gate from the solids. Because of this shielding action, the sealing surface of the lower gate is not exposed to solids during transit or when it is being lifted or lowered. The chamber containing the lower gate normally is pressurized slightly, and a sweep gas is directed inwardly across the lower-gate sealing surface during the vertical translation of the gate.

Ayers, Jr., William J. (Morgantown, WV); Carter, Charles R. (Fairmont, WV); Griffith, Richard A. (Morgantown, WV); Loomis, Richard B. (Bruceton Mills, WV); Notestein, John E. (Morgantown, WV)

1985-01-01T23:59:59.000Z

212

Double Shell Tank (DST) Transfer Valving Subsystem Specification  

Science Conference Proceedings (OSTI)

This specification establishes the performance requirements and provides references to the requisite codes and standards to be applied during design of the Double-Shell Tank (DST) Transfer Valving Subsystem that supports the first phase of Waste Feed Delivery. This specification establishes the performance requirements and provides references to the requisite codes and standards to be applied during design of the Double-Shell Tank (DST) Transfer Valving Subsystem that supports the first phase of Waste Feed Delivery (WFD). The DST Transfer Valving Subsystem routes waste and other media (e.g., diluent, flush water, filtered raw water) among DSTs and from the low-activity waste (LAW) and high-level waste (HLW) feed staging tanks to the River Protection Project (RPP) Privatization Contractor facility, where it will be processed into an immobilized waste form. This specification is intended to be the basis for new projects/installations (W-521, etc.). This specification is not intended to retroactively affect previously established project design criteria without specific direction by the program.

GRAVES, C.E.

2000-03-22T23:59:59.000Z

213

Preliminary design for hot dirty-gas control-valve test facility. Final report  

SciTech Connect

This report presents the results of a preliminary design and cost estimating effort for a facility for the testing of control valves in Hot Dirty Gas (HDGCV) service. This design was performed by Mittelhauser Corporation for the United States Department of Energy's Morgantown Energy Technology Center (METC). The objective of this effort was to provide METC with a feasible preliminary design for a test facility which could be used to evaluate valve designs under simulated service conditions and provide a technology data base for DOE and industry. In addition to the actual preliminary design of the test facility, final design/construction/operating schedules and a facility cost estimate were prepared to provide METC sufficient information with which to evaluate this design. The bases, assumptions, and limitations of this study effort are given. The tasks carried out were as follows: METC Facility Review, Environmental Control Study, Gas Generation Study, Metallurgy Review, Safety Review, Facility Process Design, Facility Conceptual Layout, Instrumentation Design, Cost Estimates, and Schedules. The report provides information regarding the methods of approach used in the various tasks involved in the completion of this study. Section 5.0 of this report presents the results of the study effort. The results obtained from the above-defined tasks are described briefly. The turnkey cost of the test facility is estimated to be $9,774,700 in fourth quarter 1979 dollars, and the annual operating cost is estimated to be $960,000 plus utilities costs which are not included because unit costs per utility were not available from METC.

Not Available

1980-01-01T23:59:59.000Z

214

A tritium-compatible piezoelectric valve for the tokamak fusion test reactor  

SciTech Connect

This work describes modifications made to a commercial piezoelectric valve to make it sufficiently tritium compatible for the TFTR trritium injection scenario. The results of testing the valve for leakage and performance following a series of progressively more severe tritium exposures are also presented. Finally, a proposal for a totally radiation-compatible piezoelectric valve, suitable for tritium-burning fusion machines of the future, is decribed. 9 refs., 2 figs., 1 tab.

Coffin, D.O.; Cole, S.P.; Wilhelm, R.C.

1988-02-01T23:59:59.000Z

215

Investigation of Main Steam Safety Valve Seat/Nozzle Surface Treatments  

Science Conference Proceedings (OSTI)

This report discusses continued research in evaluating the main steam safety valve (MSSV) high first lift phenomenon (seat sticking) experienced in some Dresser 3700 series steam safety valves. Previous EPRI research (Report TR-113560) concluded that the high first lift phenomenon is the result of adhesion of the valve disk to the nozzle seat resulting in additional opening force to separate the disk from the nozzle. Replacement of the disks with disks incorporating pre-oxidized Inconel X-750 material on...

2003-05-30T23:59:59.000Z

216

Computer Based Training: Engineering Technical Training Modules - Valve Actuator v1.0  

Science Conference Proceedings (OSTI)

Valve Actuator ETTM, Version 1.0 is a computer-based training module that allows users to access training when desired and review it at their own pace. The purpose of this training module is to provide a basic understanding of the various types of power valve actuators used in nuclear power plants and their characteristics. This module will also provide an understanding of valve actuator applications, selection, accessory requirements, and capabilities. This computer-based training (CBT) module is intend...

2009-12-04T23:59:59.000Z

217

Computer Based Training: Engineering Technical Training Module (ETTM) Relief and Safety Valves v1.0  

Science Conference Proceedings (OSTI)

Relief and Safety Valves ETTM, Version 1.0 is a computer45based training module that allows users to access training when desired and review it at their own pace. This module provides information about the types of valves, requirements surrounding their performance, characteristics and selection of these valves, as well as testing requirements. Additionally, it describes design considerations and system interactions. This training should be used for position specific and/or continuing training for indivi...

2009-11-02T23:59:59.000Z

218

Safety Valve Performance Considerations During High-Pressure Station Black-Out Severe Accidents  

Science Conference Proceedings (OSTI)

An assessment of the operating history and test performance of pressurizer safety valves (PSVs) and main steam safety valves (MSSVs) has led to new conclusions on their expected performance during high-pressure station blackout (SBO) severe accident conditions. This report updates conclusions documented in Volume I, focusing on thermal-hydraulic considerations surrounding the reactor coolant system response to an SBO and valve lifts during an SBO event. The report also reconsiders PSV and MSSV tests and ...

1998-01-02T23:59:59.000Z

219

EPRI/C-E PWR Safety Valve Test Report, Volume 10: Piping Structural Response Results  

Science Conference Proceedings (OSTI)

EPRI at the request of the PWR Utilities developed an overall program for the testing of PWR primary system safety and relief valves. This program was in response to NUREG 0578 Item 2.1.2 and NUREG 0737 Item II.D.l.A requirements.This report documents the results of safety valve testing performed as part of the overall program at the EPRI/C-E Valve Test Facility located at Combustion Engineering's Kreisinger Development Laboratory, Windsor, Connecticut. Seven safety valves ...

1983-04-01T23:59:59.000Z

220

A means for positively seating a piezoceramic element in a piezoelectric valve during inlet gas injection  

DOE Patents (OSTI)

This invention is comprised of a piezoelectric valve in a gas delivery system which includes a piezoceramic element bonded to a valve seal and disposed over a valve seat, and retained in position by an O-ring and a retainer; and insulating ball normally biased by a preload spring against the piezoceramic element; and inlet gas port positioned such that upon admission of inlet gas into the valve. The piezoceramic element is positively seated. The inelt gas port is located only on the side of the piezoceramic element opposite the seal.

Wright, K.E.

1993-12-31T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Policy Strategies and Paths to promote Sustainable Energy Systems - The dynamic Invert Simulation Tool  

E-Print Network (OSTI)

energy in particular of fossil energy is not very popular (Moderate rise of fossil energy prices by approximately 1%assumed moderate energy price increase of fossil fuels will

Stadler, Michael; Kranzl, Lukas; Huber, Claus; Haas, Reinhard; Tsioliaridou, Elena

2006-01-01T23:59:59.000Z

222

EIA - Annual Energy Outlook 2013 Early Release  

U.S. Energy Information Administration (EIA)

Solar › Energy in Brief ... the AEO2013 Reference case generally assumes that current laws and regulations affecting the energy sector remain unchanged throughout ...

223

Breakdown by magnetic field in a La{sub 0.7}Sr{sub 0.3}MnO{sub 3}/MgO/Fe spin valve  

SciTech Connect

A La{sub 0.7}Sr{sub 0.3}MnO{sub 3}/MgO/Fe spin valve with inverse tunneling magnetoresistance (TMR) was fabricated on a (100) SrTiO{sub 3} substrate by radio frequency magnetron sputtering. Giant TMR ratios up to 540% were obtained. The breakdown of the spin valve was observed at high magnetic field, which was attributed to the joint action of the invalidation of MgO barrier and the shift of Fermi energy in La{sub 0.7}Sr{sub 0.3}MnO{sub 3} at high magnetic field.

Wu Xiaojie; Meng Jian [State Key Laboratory of Rare Earth Resources Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, 5625 Renmin Street, Changchun 130022 (China); Zhang Zhenzhong [State Key Laboratory of Luminescence and Applications, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 3888 Dongnanhu Road, Changchun 130033 (China)

2012-03-19T23:59:59.000Z

224

CenterPoint Energy - Business Gas Heating Rebates (Arkansas)...  

Open Energy Info (EERE)

install natural gas energy efficiency measures such as faucet aerators and pre-rinse spray valves that reduce natural gas use as well as reducing water and sewer costs....

225

Observation and implications of magnetic domains in lateral spin valves  

Science Conference Proceedings (OSTI)

Co/Cu/Co lateral spin valves (LSV), with Co being the topmost layer, are in situ prepared and measured under ultrahigh vacuum conditions. The clean process yields a non-local spin signal of 0.9 m{Omega}. Scanning electron microscopy with polarization analysis (SEMPA) reveals domain structures in both magnetic electrodes that depend on the LSV dimensions. The spin signal correlates to SEMPA images as well as the anisotropic magnetoresistance of both Co magnets, revealing a strong impact of multi-domain states on the spin signal.

Mennig, J.; Matthes, F.; Buergler, D. E.; Schneider, C. M. [Peter Gruenberg Institute, Electronic Properties (PGI-6) and Juelich-Aachen Research Alliance, Fundamentals of Future Information Technology (JARA-FIT), Forschungszentrum Juelich GmbH, Juelich D-52425 (Germany)

2012-04-01T23:59:59.000Z

226

Endothelial Progenitor Cells as a Sole Source for Ex Vivo Seeding of Tissue-Engineered Heart Valves  

E-Print Network (OSTI)

Purposes: We investigated whether circulating endothelial progenitor cells (EPCs) can be used as a cell source for the creation of a tissue-engineered heart valve (TEHV). Methods: Trileaflet valved conduits were fabricated ...

Sales, Virna L.

227

Assuming Responsibility for Packaging and Packaging Waste  

E-Print Network (OSTI)

> Natural Resources Institute, University of ManitobaWinnipeg, Manitoba, Canada R3T 2N2.and A.J. Sinclair. (1997). "Manitoba’s Product Stewardship

Sinclair, A. John

2000-01-01T23:59:59.000Z

228

Westinghouse TRU Solutions LLC Assumes WIPP Operations  

NLE Websites -- All DOE Office Websites (Extended Search)

Manager of WTS. A retired U.S. Navy Rear Admiral, Herrera has more than 27 years of nuclear operations and radioactive waste management experience. He spent 24 years in nuclear...

229

System and method for individually testing valves in a steam turbine trip control system  

SciTech Connect

This patent describes a steam turbine power plant. It comprises: a steam generator; a steam turbine adapted to receive steam form the steam generator; a throttle valve for regulating the flow of the steam received by the steam turbine; and an electro-hydraulic trip control system for causing the throttle valve to close when a predetermined condition has been reached.

Hurley, J.D.

1992-07-28T23:59:59.000Z

230

Wakefield induced Losses in the Manual Valves of the TESLA Cryomodule  

E-Print Network (OSTI)

1 Wakefield induced Losses in the Manual Valves of the TESLA Cryomodule M.Dohlus,H.-P.Wedekind,K.Zapfe DeutschesElektronenSynchrotron Notkestr.85,D-22603Hamburg,Germany Abstract The beam pipe of the TESLA valves with spring type rf-shield which are presently used in the linac of the TESLA Test Facility

231

KIVA-3V: A block-structured KIVA program for engines with vertical or canted valves  

DOE Green Energy (OSTI)

This report describes an extended version of KIVA-3, known as KIVA-3V, that can model any number of vertical or canted valves in the cylinder head of an internal combustion (IC) engine. The valves are treated as solid objects that move through the mesh using the familiar snapper technique used for piston motion in KIVA-3. Because the valve motion is modeled exactly, and the valve shapes are as exact as the grid resolution will allow, the accuracy of the valve model is commensurate with that of the rest of the program. Other new features in KIVA-3V include a particle-based liquid wall film model, a new sorting subroutine that is linear in the number of nodes and preserves the original storage sequence, a mixing-controlled turbulent combustion model, and an optional RNG {kappa}-{epsilon} turbulence model. All features and capabilities of the original KIVA-3 have been retained. The grid generator, K3PREP, has been expanded to support the generation of grids with valves, along with the shaping of valve ports and runners. Graphics output options have also been expanded. The report discusses the new features, and includes four examples of grids with vertical and canted valves that are representative of IC engines in use today.

Amsden, A.A.

1997-07-01T23:59:59.000Z

232

System for detecting operating errors in a variable valve timing engine using pressure sensors  

SciTech Connect

A method and control module includes a pressure sensor data comparison module that compares measured pressure volume signal segments to ideal pressure volume segments. A valve actuation hardware remedy module performs a hardware remedy in response to comparing the measured pressure volume signal segments to the ideal pressure volume segments when a valve actuation hardware failure is detected.

Wiles, Matthew A.; Marriot, Craig D

2013-07-02T23:59:59.000Z

233

A New Operational Tests Circuit for Testing ±660kV UHVDC Thyristor Valves  

Science Conference Proceedings (OSTI)

Operational test is an important measure which can guarantee safe and stable operation of UHVDC thyristor valves. HVDC thyristor modules can be performed either in a six-pulse back-to-back test circuit or in a synthetic test circuit. UHVDC thyristor ... Keywords: HVDC thyristor valve, operational tests, synthetic test circuit

Ting Xie; Tang Guang-fu; Zha Kun-peng; Gao Chong

2010-06-01T23:59:59.000Z

234

Nuclear Maintenance Applications Center: Air-Operated Valve Diagnostic Testing Guide  

Science Conference Proceedings (OSTI)

This report provides information for personnel involved in the performance of air-operated valve (AOV) diagnostic testing, including the benefits of using diagnostics to understand valve health and to tie information into preventive maintenance programs. It provides insights for experienced personnel as well as basic information, guidance, and instructions for personnel assigned to perform, analyze, or purchase diagnostic test equipment.

2011-12-23T23:59:59.000Z

235

Fault Detection, Diagnosis and Prediction in Electrical Valves Using Self-Organizing Maps  

Science Conference Proceedings (OSTI)

This paper presents a proactive maintenance scheme for fault detection, diagnosis and prediction in electrical valves. The proposed scheme is validated with a case study, considering a specific valve used for controlling the oil flow in a distribution ... Keywords: Fault prediction, Proactive maintenance, Self-organizing maps, Test of electromechanical systems

Luiz Fernando Gonçalves; Jefferson Luiz Bosa; Tiago Roberto Balen; Marcelo Soares Lubaszewski; Eduardo Luis Schneider; Renato Ventura Henriques

2011-08-01T23:59:59.000Z

236

Endurance Tests of Valves With Cobalt-Free Hardfacing Alloys: PWR Phase Final Report  

Science Conference Proceedings (OSTI)

Gate valves hard-faced with three galling-resistant iron-base alloys and a cobalt-base standard were subjected to demanding cycling conditions in an environment simulating typical PWR primary chemistry conditions. Extensive nondestructive and destructive examinations showed that all valves with iron-base trim performed better than the cobalt-base standard after 1900 operating cycles.

1992-05-01T23:59:59.000Z

237

Hydraulically actuated fuel injector including a pilot operated spool valve assembly and hydraulic system using same  

DOE Patents (OSTI)

The present invention relates to hydraulic systems including hydraulically actuated fuel injectors that have a pilot operated spool valve assembly. One class of hydraulically actuated fuel injectors includes a solenoid driven pilot valve that controls the initiation of the injection event. However, during cold start conditions, hydraulic fluid, typically engine lubricating oil, is particularly viscous and is often difficult to displace through the relatively small drain path that is defined past the pilot valve member. Because the spool valve typically responds slower than expected during cold start due to the difficulty in displacing the relatively viscous oil, accurate start of injection timing can be difficult to achieve. There also exists a greater difficulty in reaching the higher end of the cold operating speed range. Therefore, the present invention utilizes a fluid evacuation valve to aid in displacement of the relatively viscous oil during cold start conditions.

Shafer, Scott F. (Morton, IL)

2002-01-01T23:59:59.000Z

238

Why Pressure Reducing Valves (PVR's) are costing you money  

E-Print Network (OSTI)

Throughout many manufacturing facilities, colleges, commercial sites or industrial complexes, pressure reducing valves (PRV's) provide a cheap, reliable method to produce low pressure steam from a high pressure source in order to meet a process requirement or heating load. This simple method of expanding steam in a PRV creates no work and supplies the same heat content available in the high pressure steam at a more manageable low pressure. What if you could produce the same low pressure steam while saving hundreds of thousands of dollars on your electric bill and taking only a minimal hit in the available heat content? Why let steam down and get no benefit from it, when putting it through a low pressure steam turbine coupled to a generator would produce the heat you need for process with the byproduct of onsite electrical generation. This paper analyzes the costs, concerns and benefits of replacing a pressure reducing valve with a Steam Turbine Generator set including illustrations of what the marginal fuel increase would be in order to take advantage of the added benefits of clean, cheap and reliable onsite power production.

Downing, A.

2012-01-01T23:59:59.000Z

239

Fluid-driven reciprocating apparatus and valving for controlling same  

DOE Patents (OSTI)

A control valve assembly for alternately actuating a pair of fluid-driven free-piston devices by using fluid pressure communication therebetween. Each control valve is switched by a pressure signal depending on the state of its counterpart's piston. The communication logic is arranged to provide overlap of the forward strokes of the pistons, so that at least one of the pair will always be pressurized. Thus, uninterrupted pumping of liquid is made possible from a pair of free-piston pumps. In addition, the speed and frequency of piston stroking is entirely dependent on the mechanical power load applied. In the case of a pair of pumps, this enables liquid delivery at a substantially constant pressure over the full range of flow rates, from zero to maximum flow. One embodiment of the invention utilized two pairs of fluid-driven free-piston devices whereby a bipropellant liquid propulsion system may be operated, so as to provide continuous flow of both fuel and oxidizer liquids when used in rocket applications, for example.

Whitehead, John C. (Davis, CA); Toews, Hans G. (East Aurora, NY)

1993-01-01T23:59:59.000Z

240

Two-phase flow characteristics in multiple orifice valves  

SciTech Connect

This work presents an experimental investigation on the characteristics of two-phase flow through multiple orifice valve (MOV), including frictional pressure drop and void fraction. Experiments were carried out using an MOV with three different sets of discs with throat thickness-diameter ratios (s/d) of 1.41, 1.66 and 2.21. Tests were run with air and water flow rates ranging between 1.0 and 3.0 m{sup 3}/h, respectively. The two-phase flow patterns established for the experiment were bubbly and slug. Two-phase frictional multipliers, frictional pressure drop and void fraction were analyzed. The determined two-phase multipliers were compared against existing correlations for gas-liquid flows. None of the correlations tested proved capable of predicting the experimental results. The large discrepancy between predicted and measured values points at the role played by valve throat geometry and thickness-diameter ratio in the hydrodynamics of two-phase flow through MOVs. A modification to the constants in the two-phase multiplier equation used for pipe flow fitted the experimental data. A comparison between computed frictional pressure drop, calculated with the modified two-phase multiplier equation and measured pressure drop yielded better agreement, with less than 20% error. (author)

Alimonti, Claudio [Sapienza University of Rome, Department ICMA, Via Eudossiana 18, 00184 Roma (Italy); Falcone, Gioia; Bello, Oladele [The Harold Vance Department of Petroleum Engineering, Texas A and M University, 3116 TAMU, Richardson Building, College Station, TX 77843 (United States)

2010-11-15T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Evaluation of wear resistant ceramic valve seats in gas-fueled power generation engines. Topical report, December 1991-April 1994  

SciTech Connect

This project is directed at the reduction of valve recession in natural gas-fueled engines. Ceramic valve seat inserts have been procured, installed in a Caterpillar G3516 natural gas generator set, and tested for 1000 hours. Two different silicon nitride materials are being utilized for the valve seats in addition to stock Eatonite metallic inserts. Three valve face materials are being tested. These include stock Caterpillar stellite 1 faced, stellite 6 faced, and unfaced valves. A test matrix was used to allow comparison of all three valve face materials in combination with all three insert materials. The testing is scheduled to continue for an additional 7000 hours. No problems have been encountered with the test materials. In general, it has been shown that two types of silicon nitride materials have at least short term durability in engine operation. Neither material has exhibited any deficiencies thus far. An economic analysis spreadsheet has been created to calculate potential cost savings potential using ceramic valve seat inserts. Valve recession data for the first 1000 hours shows expected trends. Exhaust valve positions are wearing more than intake valve positions. If the intake positions and all positions with unfaced valve are ignored, then ceramic inserts paired with Stellite 1 valves show the most wear.

Burrahm, R.W.; Branecky, R.J.; Sui, P.C.; Latusek, J.P.; Hsu, S.M.

1994-12-01T23:59:59.000Z

242

Projections of Full-Fuel-Cycle Energy and Emissions Metrics  

E-Print Network (OSTI)

U.S. supply, and it is assumed that the energy use for extraction and processing of pipeline imports

Coughlin, Katie

2013-01-01T23:59:59.000Z

243

The Free Will Theorem and the Flash Ontology implicitly assume the Before-Before Experiment and thereby imply free will. Comment on a note by Nicolas Gisin in arXiv:1002.1392v1  

E-Print Network (OSTI)

It is argued that both the "Free Will Theorem" (FWT) and the "relativistic GRW model with Flash Ontology" (rGRWf) hiddenly assume the result of the before-before experiment, and for this reason both FWT and rGRWf imply free will in the world outside free experimenters.

Suarez, Antoine

2010-01-01T23:59:59.000Z

244

The Free Will Theorem and the Flash Ontology implicitly assume the Before-Before Experiment and thereby imply free will. Comment on a note by Nicolas Gisin in arXiv:1002.1392v1  

E-Print Network (OSTI)

It is argued that both the "Free Will Theorem" (FWT) and the "relativistic GRW model with Flash Ontology" (rGRWf) hiddenly assume the result of the before-before experiment, and for this reason both FWT and rGRWf imply free will in the world outside free experimenters.

Antoine Suarez

2010-02-13T23:59:59.000Z

245

Method of accounting for code safety valve setpoint drift in safety analyses  

Science Conference Proceedings (OSTI)

In performing the safety analyses for transients that result in a challenge to the reactor coolant system (RCS) pressure boundary, the general acceptance criterion is that the peak RCS pressure not exceed the American Society of Mechanical Engineers limit of 110% of the design pressure. Without crediting non-safety-grade pressure mitigating systems, protection from this limit is mainly provided by the primary and secondary code safety valves. In theory, the combination of relief capacity and setpoints for these valves is designed to provide this protection. Generally, banks of valves are set at varying setpoints staggered by 15- to 20-psid increments to minimize the number of valves that would open by an overpressure challenge. In practice, however, when these valves are removed and tested (typically during a refueling outage), setpoints are sometimes found to have drifted by >50 psid. This drift should be accounted for during the performance of the safety analysis. This paper describes analyses performed by Yankee Atomic Electric Company (YAEC) to account for setpoint drift in safety valves from testing. The results of these analyses are used to define safety valve operability or acceptance criteria.

Rousseau, K.R.; Bergeron, P.A.

1989-01-01T23:59:59.000Z

246

Passively operated spool valve for drain-down freeze protection of thermosyphon water heaters. Final technical report  

SciTech Connect

The work done to extend the existing drain-down valve technology to provide passive drain-down freeze protection for thermosyphon-based solar water heaters is described. The basic design of the existing valve model is that of a spool valve, employing a cylindrical spool which moves axially in a mating cartridge to open and close o-rings at the two operating extremes (drain and operate) to perform the valving function. Three passive actuators to drive the basic valving mechanism were designed, fabricated, and tested. Two piping configurations used to integrate the spool valve with the thermosyphon system are described, as are the passive actuators. The three actuator designs are: photovoltaic driven, refrigerant-based bellows, and heat motor cable-drive designs. Costs are compared for the alternative actuator designs, and operating characteristics were examined for the thermosyphon system, including field tests. The market for the valve for thermosyphon systems is then assessed. (LEW)

1982-04-30T23:59:59.000Z

247

Electromagnetic valve for controlling the flow of molten, magnetic material  

DOE Patents (OSTI)

An electromagnetic valve for controlling the flow of molten, magnetic material is provided, which comprises an induction coil for generating a magnetic field in response to an applied alternating electrical current, a housing, and a refractory composite nozzle. The nozzle is comprised of an inner sleeve composed of an erosion resistant refractory material (e.g., a zirconia ceramic) through which molten, magnetic metal flows, a refractory outer shell, and an intermediate compressible refractory material, e.g., unset, high alumina, thermosetting mortar. The compressible refractory material is sandwiched between the inner sleeve and outer shell, and absorbs differential expansion stresses that develop within the nozzle due to extreme thermal gradients. The sandwiched layer of compressible refractory material prevents destructive cracks from developing in the refractory outer shell.

Richter, Tomas (State College, PA)

1998-01-01T23:59:59.000Z

248

Electromagnetic valve for controlling the flow of molten, magnetic material  

DOE Patents (OSTI)

An electromagnetic valve for controlling the flow of molten, magnetic material is provided, which comprises an induction coil for generating a magnetic field in response to an applied alternating electrical current, a housing, and a refractory composite nozzle. The nozzle is comprised of an inner sleeve composed of an erosion resistant refractory material (e.g., a zirconia ceramic) through which molten, magnetic metal flows, a refractory outer shell, and an intermediate compressible refractory material, e.g., unset, high alumina, thermosetting mortar. The compressible refractory material is sandwiched between the inner sleeve and outer shell, and absorbs differential expansion stresses that develop within the nozzle due to extreme thermal gradients. The sandwiched layer of compressible refractory material prevents destructive cracks from developing in the refractory outer shell. 5 figs.

Richter, T.

1998-06-16T23:59:59.000Z

249

Strength and fatigue of NT551 silicon nitride and NT551 diesel exhaust valves  

DOE Green Energy (OSTI)

The content of this report is excerpted from Mark Andrew's Ph.D. Thesis (Andrews, 1999), which was funded by a DOE/OTT High Temperature Materials Laboratory Graduate Fellowship. It involves the characterization of NT551 and valves fabricated with it. The motivations behind using silicon nitride (Si{sub 3}N{sub 4}) as an exhaust valve for a diesel engine are presented in this section. There are several economic factors that have encouraged the design and implementation of ceramic components for internal combustion (IC) engines. The reasons for selecting the diesel engine valve for this are also presented.

Andrews, M.J.; Werezczak, A.A.; Kirkland, T.P.; Breder, K.

2000-02-01T23:59:59.000Z

250

Proceedings of the symposium on inservice testing of pumps and valves  

Science Conference Proceedings (OSTI)

The 1990 Symposium on Inservice Testing of Pumps and Valves, jointly sponsored by the Board on Nuclear Codes and Standards of the American Society of Mechanical Engineers and by the Nuclear Regulatory Commission, provided a forum for the discussion of current programs and methods for inservice testing at nuclear power plants. The symposium also provided an opportunity to discuss the need to improve inservice testing in order to ensure the reliable performance of pumps and valves. The participation of industry representatives, regulators, and consultants resulted in the discussion of a broad spectrum of ideas and perspectives regarding the improvement of inservice testing of pumps and valves at nuclear power plants.

Not Available

1990-10-01T23:59:59.000Z

251

Enhancement of spin-dependent scattering and improvement of microstructure in spin valves by delayed deposition  

Science Conference Proceedings (OSTI)

Si/Ta/Co/Cu/CoFeMn (or NiO) spin valves were prepared by a delayed sputtering procedure, in which depositions of Ta and followed layers were intervened by 1 h. The spin valves are found to have better coherent growth with stronger (111) preferred orientations in Co and Cu layers, compared with the traditional continuous method. At the same time, the giant magnetoresistance ratio and spin-dependent scattering are enhanced by a factor of 20%-30%. These results indicate that the coherent growth and the (111) preferred orientation can enhance the spin-dependent scattering of spin valves.

Yang, D.Z.; Wang, L.; Yang, X.J.; Zhou, S.M.; Wu, X.S.; Du, J.; Hu, A.; Zhang, X.X. [Surface Physics Laboratory (State Key Laboratory) and Department of Physics, Fudan University, Shanghai 200433 (China) and Department of Physics, Southeast University, Nanjing 210096 (China); Surface Physics Laboratory (State Key Laboratory) and Department of Physics, Fudan University, Shanghai 200433 (China); National Laboratory of Solid State Microstructures and Department of Physics, Nanjing University, Nanjing 210093 (China); Department of Physics, Hong Kong University of Science and Technology, Kowloon, Hong Kong (China)

2005-06-20T23:59:59.000Z

252

Endurance Tests of Valves With Cobalt-Free Hardfacing Alloys: BWR Phase Final Report  

Science Conference Proceedings (OSTI)

Valves hardfaced with three galling-resistant iron-base alloys (NOREM, EVERIT 50, and Deloro Stellite EB 5183) and a cobalt-base standard (Stellite 6) were subjected to stroke cycling in an environment simulating BWR chemistry conditions. Examination showed that the wear performance of valves with iron-base trim matched that of the cobalt-base standard. Yet, preferential corrosion of EB 5183 was found. Using cobalt-free alloys to replace or refurbish valves will significantly reduce released cobalt respo...

1993-03-01T23:59:59.000Z

253

Analysis of Long-range Clean Energy Investment Scenarios for Eritrea, East Africa  

E-Print Network (OSTI)

benefits and costs of energy efficiency and renewableand Costs Fundamentally, investments in energy efficiency and renewableand cost estimates and forecasts assumed for energy efficiency and renewable

Van Buskirk, Robert D.

2004-01-01T23:59:59.000Z

254

Federal Energy Management Program: Energy Savings Calculator...  

NLE Websites -- All DOE Office Websites (Extended Search)

discounted value of annual energy costs, based on an assumed chiller life of 23 years. Price trends and discount rate - Future electricity price trends and a discount rate of 3%...

255

Failure testing of active solar energy components  

SciTech Connect

Component and system reliability of active solar energy systems continue to be a major concern of designers, manufacturers, installers, and consumers. Six test loops were constructed and the Solar Energy Research Institute, in Golden, Colorado, to thermally cycle active solar energy system components. Drain valves, check valves, air vents, vacuum breakers, tempering valves, and polybutylene pipe were included in the testing. The test methods and results are discussed in this report. Test results show poor reliability of some of the components and limited performance from others. The results lead to a better understanding of certain failures in the field and present designers with realistic expectations for these components. Recommendations are given to improve component reliability and for further testing.

Farrington, R.B.

1984-07-01T23:59:59.000Z

256

Microsoft Word - Energy Code Enforcement Funding Task Force ...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

of EIA's Annual Energy Outlook 2010, including projected construction levels, energy consumption, and fuel prices. The task force conservatively assumed a 4-year payback period...

257

United States - U.S. Energy Information Administration (EIA ...  

U.S. Energy Information Administration (EIA)

Energy Information Administration ... Energy use in homes, commercial buildings, ... consumption data are no longer collected and are assumed to be ze ...

258

Energy Savings By Recovery of Condensate From Steam Heating System  

E-Print Network (OSTI)

The recovery and utilization of condensate has a remarkable energy saving effect if the following are properly done: 1) Determination of a correct and reasonable recovery plan; 2) Selection of bleed valve with good performance; 3) Solving the problem of air bleeding, and 4) Scientific management of condensate system and bleed valve. If the above mentioned points are well dealt with, the recovery and utilization of condensate will be very beneficial.

Cheng, W. S.; Zhi, C. S.

1985-05-01T23:59:59.000Z

259

Percutaneous aortic valve replacement in a re-animated postmortem heart  

E-Print Network (OSTI)

transcatheter implantation of heart valve prosthesis for thein apex of post-mortem heart (lower view). B C A Figure 5A.descending aorta in lambs. Eur Heart J. 2002;23:1045-49. 5.

White, Jennifer; Sun, Amy; Killien, Lauren; Evangelista, Dennis

2006-01-01T23:59:59.000Z

260

Dynamic simulation of heart mitral valve with transversely isotropic material model  

E-Print Network (OSTI)

This thesis develops two methods for simulating, in the finite element setting, the material behavior of heart mitral valve leaflet tissue. First, a mixed pressure-displacement formulation is used to implement the constitutive ...

Weinberg, Eli, 1979-

2005-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Safety Evaluation Report, pump and valve inservice testing program, Maine Yankee Atomic Power Station  

Science Conference Proceedings (OSTI)

This EG and G, Inc., report presents the results of our evaluation of the Maine Yankee Atomic Power Station, Inservice Testing Program for pumps and valves whose function is important to safety.

Rockhold, H.C.; Stromberg, H.M.

1985-04-01T23:59:59.000Z

262

Electro-Hydraulic Servo-Valve and Motion and Control Loading of Full Flight Simulator.  

E-Print Network (OSTI)

??The present thesis is on the subject of electro-hydraulic servo-valve (EHV), and motion and control loading of a flight simulator with EHV. The fundamentals of… (more)

Shi, Wei

2010-01-01T23:59:59.000Z

263

Closed-loop, variable-valve-timing control of a controlled-auto-ignition engine  

E-Print Network (OSTI)

The objective of this study was to develop a closed-loop controller for use on a Controlled-Auto- Ignition (CAI) / Spark-Ignition (SI) mixed mode engine equipped with a variable-valve-timing (VVT) mechanism. The controller ...

Matthews, Jeffrey A., 1970-

2004-01-01T23:59:59.000Z

264

DOE specification: Valve-regulated type lead-acid storage batteries  

DOE Green Energy (OSTI)

This document contains a ``fill-in-the-blanks`` guide specification for procurement of sealed valve-regulated type lead-acid storage batteries, for uninterruptible power supply applications.

NONE

1996-08-01T23:59:59.000Z

265

Template for Submission of Risk-Informed Inservice Testing Program for Pumps and Valves  

Science Conference Proceedings (OSTI)

Nuclear power plants must update their inservice testing program for pumps and valves to the latest ASME code every ten years. This report provides a template for requesting an alternative to the technical requirements contained in that code.

1998-09-17T23:59:59.000Z

266

VALVE FUNNEL SPRING PIN PRESS PERFORMANCE AND FUNCTIONAL REQUIREMENTS EVALUATION FOR SPECIAL TOOLS AND EQUIPMENT  

SciTech Connect

This evaluation allows use of the valve funnel spring pin press and describes appropriate handling instructions for the tool. The engineering evaluation is required for operations and field use of special tools and equipment.

WITHERSPOON JT

2009-12-30T23:59:59.000Z

267

Granular Attrition due to Rotary Valve in a Pneumatic Conveying System  

E-Print Network (OSTI)

The rotary valve is a widely used mechanical device in many solids-handling industrial processes. However, it may also be responsible for most of the attrition effects occurring in a typical process. In this study, the ...

Yao, Jun

268

Energy  

Site Map; Printable Version; Share this resource. Send a link to Full Size Image - Energy Innovation Portalto someone by E-mail; Share Full Size Image - Energy ...

269

Method and apparatus utilizing valve throttling and charge stratification in the operation of an internal combustion engine  

Science Conference Proceedings (OSTI)

In an internal combustion engine this patent describes means forming a combustion chamber, a spark plug in the chamber, a piston disposed in the chamber for reciprocable movement toward and away from the spark plug, a valve member, circular seat means for the valve member, means for varying the lift of the valve member, a generally cylindrical shroud corresponding generally to the size of the seat means. The cylindrical shroud is relieved only in the direction of the spark plug so that, when the valve member is moved relative to the shroud by the lift-varying means, a stratified mixture of air and fuel is directed toward the spark plug until the lift-varying means causes the valve member to pass beyond the shroud so that during the initial lift of the valve member the stratified air and fuel mixture is directed solely toward the spark plug until the valve member passes beyond the shroud and the air and fuel mixture is directed generally through a 360/sup 0/ arc after the valve member passes beyond the shroud, and means limiting the lift of the valve member so that it does not pass the shroud during lighter loads, whereby the air and fuel mixture is directed primarily toward the spark plug until the valve member passes beyond the shroud.

Burandt, C.O.

1988-02-16T23:59:59.000Z

270

Nanostructured Coatings for Improved Erosion Resistance of Valve Stem Materials – 2013 Field Test Trials Update  

Science Conference Proceedings (OSTI)

The Electric Power Research Institute- (EPRI-) developed nanostructured coatings (nanocoatings), deposited by plasma- enhanced magnetron sputtering, show great promise for improved erosion and wear resistance in many power plant applications. EPRI laboratory research in 2010 developed the processing to apply these coatings over nitrided/malcomized (hardened) steam turbine valve stems, which is described in EPRI report 1019796, Application of Nanocoatings for Erosion Protection of Valve ...

2013-12-20T23:59:59.000Z

271

AECL Qualification of Greases for Motor-Operated Valve Stem/Stem Nut Lubrication  

Science Conference Proceedings (OSTI)

The frictional characteristics of lubricants used in the actuators of motor-operated valves are critical to ensuring adequate actuator output capability. As part of the EPRI Motor-Operated Valve (MOV) Performance Prediction Program, testing was conducted at ambient temperature conditions on over 20 stem-stem nut lubricants in use in United States nuclear plants as documented in EPRI report TR-103235. Additional research has been conducted on several MOV lubricants after thermal and radiation aging under ...

1998-11-24T23:59:59.000Z

272

Energy Commission  

E-Print Network (OSTI)

This report was prepared as the result of work sponsored by the California Energy Commission. It does not necessarily represent the views of the Energy Commission, its employees or the State of California. The Energy Commission, the State of California, its employees, contractors and subcontractors make no warrant, express or implied, and assume no legal liability for the information in this report; nor does any party represent that the uses of this information will not infringe upon privately owned rights. This report has not been approved or disapproved by the California Energy Commission nor has the California Energy Commission passed upon the accuracy or adequacy of the information in this report. ii ACKNOWLEDGMENTS

Larry Waterland; M. Lorraine White; James J. Folkman; Ray Tuvell; Rosella Shapiro; B. B Blevins; Larry Waterl; Stefan Unnasch; Michael Jackson; M. Lorraine White; James M. Folkman; Sherry Stoner; Mckinley Addy; Asish Gautam; Tom Macdonald; Mike Mccormack; Tim Olson; Peter Quinliven

2006-01-01T23:59:59.000Z

273

THE VALVE-ACTUATED PULSE COLUMN DESIGN AND OPERATION  

SciTech Connect

A countercurrent extraction column is described which employs timed solenoid valves and pressurized feeds to provide a pulsing action to disperse the phases. The steps in the pulsing cycle are independent and thus provide greater separation of the operating variables than is possible with conventional pulse columns. The column described is particularly useful as a resesrch tool for the study of extraction mechanism although a larger installation operating on the same principles should be quite workable. The 4-stage-cycle or mixersettler type column operation has an inherent advantage in that the rapid coalescence and redispersion of phases are believed to lead to greater extraction than simple movement of a dispersed phase through a continuous medium. In addition, the sharp pulse provided should produce greater turbulence than the more conventional pulsing arrangement. Some results of operation on the extraction and stripping of uranyl nitrate using tributyl phosphate as a solvent are included. These data correspond to Metal Recovery and Erex type systems. (auth)

Burger, L.L.; Clark, L.H.

1951-12-01T23:59:59.000Z

274

Nuclear Maintenance Applications Center: Application Guide for Motor-Operated Valves in Nuclear Power Plants - Revision 2  

Science Conference Proceedings (OSTI)

Motor-operated gate and globe valves are widely used in both safety-related and non-safety-related systems in nuclear power plants. Their proper operation is essential for reliable plant performance and can help eliminate costly downtime. This second revision of the Application Guide for Motor-Operated Valves provides the latest in methods for conducting engineering evaluations in order to confirm that motor-operated gate, globe, and butterfly valves will perform their required function and offers sugges...

2007-08-22T23:59:59.000Z

275

SHORT-TERM - Energy Information Administration  

U.S. Energy Information Administration (EIA)

Analysis and Forecasting Division (202/586-5382). Macroeconomic Forecast: Energy Product Prices: ... scenario, it is assumed that, after the first

276

Acceptance test report for the AN valve pit leak detection and low point drain assembly mock up test procedure  

SciTech Connect

This document describes The Performance Mock-up Test Procedure for the Valve Pit Leak Detection and Low Point Drain Assembly Performance Mock-Up Test Procedure.

EWER, K.L.

1999-07-20T23:59:59.000Z

277

Energy  

Science Conference Proceedings (OSTI)

Energy. Summary: Key metrologies/systems: Scanning tunneling microscopy and one- and two-photon photoemission/Model ...

2012-10-02T23:59:59.000Z

278

Energy  

Home. Site Map; Printable Version; Share this resource. About; Search; Categories (15) Advanced Materials; Biomass and Biofuels; Building Energy Efficiency ...

279

ISOLOK VALVE ACCEPTANCE TESTING FOR DWPF SME SAMPLING PROCESS  

Science Conference Proceedings (OSTI)

Evaluation of the Defense Waste Processing Facility (DWPF) Chemical Process Cell (CPC) cycle time identified several opportunities to improve the CPC processing time. Of the opportunities, a focus area related to optimizing the equipment and efficiency of the sample turnaround time for DWPF Analytical Laboratory was identified. The Mechanical Systems & Custom Equipment Development (MS&CED) Section of the Savannah River National Laboratory (SRNL) evaluated the possibility of using an Isolok{reg_sign} sampling valve as an alternative to the Hydragard{reg_sign} valve for taking process samples. Previous viability testing was conducted with favorable results using the Isolok sampler and reported in SRNL-STI-2010-00749 (1). This task has the potential to improve operability, reduce maintenance time and decrease CPC cycle time. This report summarizes the results from acceptance testing which was requested in Task Technical Request (TTR) HLW-DWPF-TTR-2010-0036 (2) and which was conducted as outlined in Task Technical and Quality Assurance Plan (TTQAP) SRNL-RP-2011-00145 (3). The Isolok to be tested is the same model which was tested, qualified, and installed in the Sludge Receipt Adjustment Tank (SRAT) sample system. RW-0333P QA requirements apply to this task. This task was to qualify the Isolok sampler for use in the DWPF Slurry Mix Evaporator (SME) sampling process. The Hydragard, which is the current baseline sampling method, was used for comparison to the Isolok sampling data. The Isolok sampler is an air powered grab sampler used to 'pull' a sample volume from a process line. The operation of the sampler is shown in Figure 1. The image on the left shows the Isolok's spool extended into the process line and the image on the right shows the sampler retracted and then dispensing the liquid into the sampling container. To determine tank homogeneity, a Coliwasa sampler was used to grab samples at a high and low location within the mixing tank. Data from the two locations were compared to determine if the contents of the tank were well mixed. The Coliwasa sampler is a tube with a stopper at the bottom and is designed to obtain grab samples from specific locations within the drum contents. A position paper (4) was issued to address the prototypic flow loop issues and simulant selections. A statistically designed plan (5) was issued to address the total number of samples each sampler needed to pull, to provide the random order in which samples were pulled and to group samples for elemental analysis. The TTR required that the Isolok sampler perform as well as the Hydragard sampler during these tests to ensure the acceptability of the Isolok sampler for use in the DWPF sampling cells. Procedure No.L9.4-5015 was used to document the sample parameters and process steps. Completed procedures are located in R&D Engineering job folder 23269.

Edwards, T.; Hera, K.; Coleman, C.; Jones, M.; Wiedenman, B.

2011-12-05T23:59:59.000Z

280

Heart valve cardiomyocytes of mouse embryos express the serotonin transporter SERT  

SciTech Connect

Multiple evidence demonstrate a role for serotonin and its transporter SERT in heart valve development and disease. By utilizing a Cre/loxP system driven by SERT gene expression, we recently demonstrated a regionally restricted distribution of SERT-expressing cells in developing mouse heart. In order to characterize the cell types exhibiting SERT expression within the mouse heart valves at early developmental stages, in this study we performed immunohistochemistry for Islet1 (Isl1) and connexin-43 (Cx-43) on heart sections from SERT{sup Cre/+};ROSA26R embryos previously stained with X-gal. We observed the co-localization of LacZ staining with Isl1 labelling in the outflow tract, the right ventricle and the conal region of E11.5 mouse heart. Cx-43 labelled cells co-localized with LacZ stained cells in the forming atrioventricular valves. These results demonstrate the cardiomyocyte phenotype of SERT-expressing cells in heart valves of the developing mouse heart, thus suggesting an active role of SERT in early heart valve development.

Pavone, Luigi Michele [Department of Biological Structures, Functions and Technologies, University of Naples Federico II, Via F. Delpino 1, 80137 Naples (Italy); Department of Biochemistry and Medical Biotechnologies, University of Naples Federico II, Naples (Italy)], E-mail: pavone@dbbm.unina.it; Spina, Anna; Lo Muto, Roberta; Santoro, Dionea [Department of Biological Structures, Functions and Technologies, University of Naples Federico II, Via F. Delpino 1, 80137 Naples (Italy); Department of Biochemistry and Medical Biotechnologies, University of Naples Federico II, Naples (Italy); Mastellone, Vincenzo [Department of Experimental Medicine 'G. Salvatore', University of Magna Graecia, Catanzaro (Italy); Avallone, Luigi [Department of Biological Structures, Functions and Technologies, University of Naples Federico II, Via F. Delpino 1, 80137 Naples (Italy)

2008-12-12T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Uncertainty Analysis for a Virtual Flow Meter Using an Air-Handling Unit Chilled Water Valve  

SciTech Connect

A virtual water flow meter is developed that uses the chilled water control valve on an air-handling unit as a measurement device. The flow rate of water through the valve is calculated using the differential pressure across the valve and its associated coil, the valve command, and an empirically determined valve characteristic curve. Thus, the probability of error in the measurements is significantly greater than for conventionally manufactured flow meters. In this paper, mathematical models are developed and used to conduct uncertainty analysis for the virtual flow meter, and the results from the virtual meter are compared to measurements made with an ultrasonic flow meter. Theoretical uncertainty analysis shows that the total uncertainty in flow rates from the virtual flow meter is 1.46% with 95% confidence; comparison of virtual flow meter results with measurements from an ultrasonic flow meter yielded anuncertainty of 1.46% with 99% confidence. The comparable results from the theoretical uncertainty analysis and empirical comparison with the ultrasonic flow meter corroborate each other, and tend to validate the approach to computationally estimating uncertainty for virtual sensors introduced in this study.

Song, Li; Wang, Gang; Brambley, Michael R.

2013-04-28T23:59:59.000Z

282

Apparatus and method for non-invasive diagnosis and control of motor operated valve condition  

DOE Patents (OSTI)

An apparatus compares the torque from an MOV motor with the valve displacement, and from the comparison assesses MOV operating condition. A transducer measures the vibration of the housing of an MOV. The vibrations are due to the motions of the rotating elements within the housing, which motions are directly related to the motion of the valve relative to its seat. Signal processing apparatus analyzes the vibrations to recover the rotations of the rotating elements and thus the motion of the valve plug. Lost motion can also be determined (if a lost motion connection exists) by demodulating the vibration signal and thus taking into account also the lost motion. Simultaneously, the forces applied to the valve are estimated by estimating the torque between the stator and the rotor of the motor. Such torque can be estimated from measuring the input current and voltage alone, using a forgetting factor and a correction for the forgetting factor. A signature derived from relating the torque to the valve position can be used to assess the condition of the MOV, by comparing the signature to signatures for MOVs of known conditions. The vibration analysis components generate signals that relate to the position of elements in the operator. Similarly, the torque estimator estimates the torque output by any type of electric motor, whether or not part of an MOV analysis unit. 28 figs.

Lyon, R.H.; Chai, J.; Lang, J.H.; Hagman, W.H.; Umans, S.D.; Saarela, O.J.

1997-01-14T23:59:59.000Z

283

Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

Energy Energy Energy Express Licensing Accelerator-Driven Transmutation Of Spent Fuel Elements Express Licensing Acid-catalyzed dehydrogenation of amine-boranes Express Licensing Air Breathing Direct Methanol Fuel Cell Express Licensing Aligned Crystalline Semiconducting Film On A Glass Substrate And Method Of Making Express Licensing Anion-Conducting Polymer, Composition, And Membrane Express Licensing Apparatus for Producing Voltage and Current Pulses Express Licensing Biaxially oriented film on flexible polymeric substrate Express Licensing Corrosion Test Cell For Bipolar Plates Express Licensing Device for hydrogen separation and method Negotiable Licensing Durable Fuel Cell Membrane Electrode Assembly (MEA) Express Licensing Energy Efficient Synthesis Of Boranes Express Licensing

284

Energy  

Science Conference Proceedings (OSTI)

There has been a significant progress in converting solar energy using silicon technology to replace fossil fuels. However, its high cost of production has led ...

285

Energy  

Efficient, Low-cost Microchannel Heat Exchanger. Return to Marketing Summary. Skip footer navigation to end of page. ... Energy Innovation Portal on Facebook;

286

Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

energy, including Fundamental advances in nuclear fuels Nonproliferation safeguards Reactor concepts Reactor waste disposition Animation of new reactor concept for deep space...

287

Hydraulic waste energy recovery, Phase 2  

SciTech Connect

The energy required for booster station operation is supplied by the electrical utility company and has an associated cost. Energy removed by pressure reducing valves in the system is lost or wasted. The objective of this project is to capture the wasted hydraulic energy with in-line turbines. In this application, the in-line turbines act as pressure reducing valves while removing energy from the water distribution system and converting it to electrical energy. The North Service Center pumping station was selected for the pilot program due to the availability of a wide range in pressure drop and flow, which are necessary for hydraulic energy recovery. The research performed during this project resulted in documentation of technical, economic, installation, and operational information necessary for local government officials to make an informed judgement as it relates to in-line turbine generation.

1992-02-01T23:59:59.000Z

288

English-Spanish glossary: offshore exploration and production, gas processing, and valves  

Science Conference Proceedings (OSTI)

This series of articles contains 3 different English-Spanish glossaries of related terms used in the oil industry. The glossary of the offshore exploration and production involves a summary of terms used in the offshore oil activity. It also includes names of singular equipment used in offshore drilling, as well as several navigation terms in relation to the floating oil structures. With the help of the Gas Processors Association it was possible to compile a glossary of gas processing with a concise selection of common terms of the industry of gas processing. The glossary of valves includes more than 200 terms of the industry of valves in a specialized glossary, and several explanations about the application and operation of valves.

Not Available

1981-12-01T23:59:59.000Z

289

Failure analyses of two ball valves used for coal-gasification applications  

SciTech Connect

Two ball valves which had failed by developing excess leakage were supplied for analyses. The 2'' (51 mm) valve had experienced 5000 cycles during 20 hrs usage in an unknown chemical environment. Wear on the ball and seats was a multi-stage process starting with breakdown of a hard chrome plating on the stainless steel ball. This eventually led to adhesive weld transfer of the stainless steel to the seat made of Stellite 6 alloy. The 6'' (152 mm) ball valve had experienced a cycling test sequence using compressed air up to 300 psig (2.07 MPa) at 850/sup 0/F (727/sup 0/K). Damage was characterized as abrasive wear caused either by particles deposited by the compressed air or by carbide particles present in the Stellite 6 alloy ball and seat hardfacing. The decrease in this alloy's compressive yield strength at the elevated test temperature contributed to increased wear rates.

Van Den Avyle, J.A.; Pope, L.E.

1982-07-01T23:59:59.000Z

290

An approach for modeling the valve train system to control the homogeneous combustion in a compression ignition engine  

Science Conference Proceedings (OSTI)

This paper presents an approach for modeling the valve train system to obtain a homogeneous charge compression ignition (HCCI) engine from a gasoline engine. The HCCI engines use different indirect strategies to control the start of the combustion. The ... Keywords: exhaust gas recirculation, homogeneous charge compression ignition, variable valve timing

Radu Cosgarea; Corneliu Cofaru; Mihai Aleonte; Maria Luminita Scutaru; Liviu Jelenschi; Gabriel Sandu

2011-04-01T23:59:59.000Z

291

Whitey Swagelok SCHe ball valves Provide Isolation between SCHe Purge Lines C and D and the Process Vent  

Science Conference Proceedings (OSTI)

These valves are 1/4 inch ball valves fabricated of 316 stainless steel. Packing is TFE (standard). They provide an isolation function betwen SCHe Purge Line C, (PV-V-*079), and Purge Line D, (PV-V-*080), and the Process Vent.

MISKA, C.R.

2000-09-03T23:59:59.000Z

292

Fail Save Shut Off Valve for Filtering Systems Employing Candle Filters  

DOE Patents (OSTI)

The invention relates to an apparatus that acts as a fail save shut off valve. More specifically, the invention relates to a fail save shut off valve that allows fluid flow during normal operational conditions, but prevents the flow of fluids in the event of system failure upstream that causes over-pressurization. The present invention is particularly well suited for use in conjunction with hot gas filtering systems, which utilize ceramic candle filters. Used in such a hot gas system the present invention stops the flow of hot gas and prevents any particulate laden gas from entering the clean side of the system.

VanOsdol, John

2006-01-03T23:59:59.000Z

293

Results of the independent radiological verification survey at the former Chapman Valve Manufacturing Company, Indian Orchard, Massachusetts (CIO001V)  

SciTech Connect

The Chapman Valve Manufacturing Company in Indian Orchard, Massachusetts was one of many companies performing work during the 1940s associated with the development of nuclear energy for defense-related projects for the Manhattan Engineer District (MED) and the Atomic Energy Commission (AEC). In 1991, a radiological survey was conducted at the site. The survey report indicated {sup 238}U contamination in excess of the DOE criteria for surface contamination, and some {sup 235}U residues in the west end of the building. Decontamination of the facility to supplemental guidelines, derived by a hazard assessment based on appropriate scenarios for this building, was conducted by subcontractor personnel in 1995 under the direction of Bechtel National Incorporated (BNI), the project management contractor for FUSRAP. The independent radiological verification survey detailed in this report was performed in July and August 1995 under the FUSRAP program by members of ORNL at the request of DOE. The radiological verification survey of the west end of the building included gamma, alpha, and beta-gamma scans for fixed contamination, smear sampling for transferable contamination, and radionuclide analysis of soil samples taken from outside the building and from excavations in the concrete floor inside the building.

Rodriguez, R.E.; Johnson, C.A.

1997-05-01T23:59:59.000Z

294

Numerical analysis of the heat transfer for packing design of cryogenic gate valve  

Science Conference Proceedings (OSTI)

The packing, among the components comprising the gate valve, is used to sustain the airtightness and the study on change of shape or pattern has been carried out to maximize the functions, but the study on changing the location or the size of the packing ... Keywords: cryogenic, heat transfer, liquefied natural gas, numerical analysis, packing

Si Pom Kim; Rock Won Jeon; Il Ju Hwang; Jae Hoon Lee; Won Heaop Shin

2012-04-01T23:59:59.000Z

295

New electromagnetic methods for the evaluation of prosthetic heart valves (invited)  

Science Conference Proceedings (OSTI)

Prosthetic devices are being implanted at record levels as the nation “ages” and advances in prosthetic science are made. Devices that are implanted range from artificial limbs and hips to devices such as heart valves. Periodic evaluation of the state of the devices is of significant interest particularly in the case of prosthetics whose failure can be fatal. An example of such a device is the artificial heart valve. Heart valves are usually replaced when stenosis or incompetence is indicated. This article presents a selection of some new techniques that are being developed for the detection of outlet strut failures in Bjork-Shiley heart valves. Methods that show particular promise include a noninvasive electromagnetic method that relies on the excitation and measurement of the resonant vibration modes of the strut. An alternate approach involves the induction of currents in the outlet strut using a pair of external excitation coils. The field generated by the current induced in the strut perturbs the field generated by the excitation coils. The field perturbations are measured using a catheter-mounted gradiometer. Test results obtained using an experimental rig designed to demonstrate the proof-of-concept are presented.

Satish Udpa

2002-01-01T23:59:59.000Z

296

Mathematical Modeling of Current-Interrupt and Pulse Operation of Valve-Regulated Lead Acid Cells  

E-Print Network (OSTI)

are resolved. Of the two candidate battery systems, the low cost and ease of operation of the VRLA battery the last decade, advanced batteries have re- ceived much attention. At present, only the valve-regulated lead acid VRLA and the nickel-metal hydride Ni-MH battery are being actively considered

297

A valve with seat?slope proportional to flow area at all poppet positions  

Science Conference Proceedings (OSTI)

An adjustable gas?blending apparatus is hypothesized that would maintain a consistent mixture over a broad range of flowrates. The design equations for the unique valve seat required for such an apparatus are developed and solved numerically. An example seat is calculated and illustrated in table form. For preliminary study

D. W. Guillaume; D. DeVries

1991-01-01T23:59:59.000Z

298

Strength and Fatigue of NT551 Silicon Nitride and NT551 Diesel Exhaust Valves  

DOE Green Energy (OSTI)

The content of this report is excerpted from Mark Andrew's Ph.D. Thesis (Andrews, 1999), which was funded by a DOEYOTT High Temperature Materials Laboratory Graduate Fellowship. It involves the characterization of NT551 and valves fabricated with it. Greater detail of the described issues may be found in that reference or through communications with Andrew Wereszczak.

Andrews, M.J.; Wereszczak, A.A.; Kirkland, T.P.; Breder, K.

2000-02-01T23:59:59.000Z

299

Temperature impacts on the set pressure of soft seated pressure relief valves  

SciTech Connect

From a safety standpoint, regardless of plant or facility type, the most important pieces of equipment are the pressure relief devices. The most critical characteristics of a pressure relief device are its set pressure and the related relieving capacity. The Set Pressure of a pressure relief device is defined as that value of increasing inlet static pressure at which the discharge becomes continuous (ASME PTC 25-1994, Performance Test Codes). To preclude an unsafe overpressure situation, the set pressure of the pressure relief device must not exceed the maximum allowable working pressure of the equipment or system being protected. Because of testing facility limitations, size or pressure, pressure relief valves intended for elevated temperature service are often set using ambient temperature air. Adjustments are made to the ambient valve opening pressures to compensate for the temperature differences. The extent of the adjustments to the pressure relief valve set pressure is important to ensure the valve will provide the required overpressure protection at the elevated in-service temperature.

Engel, J.J.; Zirps, G.T.; Gleason, R.B. [and others

1995-11-01T23:59:59.000Z

300

Predicted Effects of Tritium Exposures on Fast-Acting Piezoelectric Valves for Gas Fueling at TFTR  

SciTech Connect

The prospects for using piezoelectrically-driven valves with elastomeric or thermoplastic poppets in tritium gas service have been investigated. A modelling study of a typical valve incorporating ethylene-propylene rubber (EPR) or high density polyethylene (HDPE) was performed. Equations were developed linking applied voltage; ceramic bimorph preloading force, elastic deflection modulus, and specific deflection force (per volt applied); polymer elastic modulus, thickness, seal surface area, and compression (to make seal); elastomer compression set; thermoplastic creep modulus; and flow gap between seat and polymer tip. It was determined that, while EPR should seal the valve orifice more easily, HDPE should produce a valve flow rate vs. voltage curve less variant with time and exposure. Both should, however, be sealable and allow flow curves perturbed by less than or equal to 10% of full scale after ~100 days of exposure to 10{sup}5 Pa (1 atm) T{sub}2 gas (equivalent to ~7 x 10{sup}7 rad = 7 x 10{sup}5 Gy dosage).

Gill, J. T.; Pierce, C. W.

1985-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Condition monitoring of motor-operated valves in nuclear power plants Pierre Granjon  

E-Print Network (OSTI)

to the valve and increases radiation exposure of operators, leading to long overhaul outage and high techniques rely on the measurement of an internal mechanical quantity and require the presence of human of any internal MOV quantity. In this article, the instantaneous active power absorbed by the induction

Paris-Sud XI, Université de

302

Technical Repair Guidelines for Limitorque Models SMB 0 Through 4 Valve Actuators  

Science Conference Proceedings (OSTI)

This technical repair guide for Limitorque motor-operated valve (MOV) actuator models SMB 0 through 4 represents the third in a series of documents devoted to the comprehensive maintenance and repair of Limitorque actuators. This guide provides instructions for engineering, operations, and maintenance personnel on MOV actuator repair, maintenance, adjustment, and troubleshooting methods.

1993-02-28T23:59:59.000Z

303

Robust Digital Valve for Prosthetic Finger, Robotics, Microsurgery  

2 Managed by UT-Battelle for the U.S. Department of Energy Presentation_name Technology •Small hydraulic system for high strength, very small control of robotic systems

304

Energy  

Office of Legacy Management (LM)

..) ".. ..) ".. _,; ,' . ' , ,; Depar?.me.nt ,of.' Energy Washington; DC 20585 : . ' , - $$ o"\ ' ~' ,' DEC ?;$ ;y4,,, ~ ' .~ The Honorable John Kalwitz , 200 E. Wells Street Milwaukee, W~isconsin 53202, . . i :. Dear,Mayor 'Kalwitz: " . " Secretary of Energy Hazel' O'Leary has announceha new,approach 'to,openness in " the Department of Ene~rgy (DOE) and its communications with'the public. In -. support of~this initiative, we areipleased to forward the enclosed information related to the Milwaukee Ai.rport site in your jurisdiction that performed work, for DOE orits predecessor agencies. information; use, and retention. ., This information .is provided for your '/ ,' DOE's Formerly Utilized Sites Remedial:'Action~'Prog&is responsible for ,"'

305

A characterization of check valve degradation and failure experience in the nuclear power industry: 1984-1990. Volume 1  

SciTech Connect

Check valve operating problems in recent years have resulted in significant operating transients, increased cost and decreased system availability. As a result, additional attention has beau given to check valves by utilities (resulting in the formation of the Nuclear Industry Check Valve Group), as well as the US Nuclear Regulatory Commission and the American Society of Mechanical Engineers Operation and Maintenance Committee. All these organizations have the fundamental goal of ensuring reliable operation of check valves. A key ingredient to an engineering-oriented reliability improvement effort is a thorough understanding of relevant historical experience. A detailed review of historical failure data, available through the Institute of Nuclear Power Operation`s Nuclear Plant Reliability Data System, has been conducted. The focus of the review is on check valve failures that have involved significant degradation of the valve internal parts. A variety of parameters are considered, including size, age, system of service, method of failure discovery, the affected valve parts, attributed causes, and corrective actions.

Casada, D.A.; Todd, M.D. [Oak Ridge National Lab., TN (United States)] [Oak Ridge National Lab., TN (United States)

1993-09-01T23:59:59.000Z

306

Data:D48c3616-8527-403d-ac82-dd96cc373c32 | Open Energy Information  

Open Energy Info (EERE)

& Small Power Sector: Commercial Description: Source or reference: http:www.highwest-energy.compublicindex.phpcustservicescontent-all-comcontent-viewsrates Assume net...

307

Data:470e365b-6ea6-40a9-96a6-7137691d0a36 | Open Energy Information  

Open Energy Info (EERE)

& Small Power Sector: Commercial Description: Source or reference: http:www.highwest-energy.compublicindex.phpcustservicescontent-all-comcontent-viewsrates Assume net...

308

Federal Energy Management Program: Federal Requirements and Acquisitio...  

NLE Websites -- All DOE Office Websites (Extended Search)

Federal purchasers may assume that ENERGY STAR-qualified products and products meeting FEMP-designated efficiency requirements are life-cycle cost effective. However, users...

309

Optimization Online - Optimal management and sizing of energy ...  

E-Print Network (OSTI)

Jul 30, 2012 ... Assuming the renewable energy, demand and prices evolve as ... the ratio of the amortized cost of storage to the price of electricity should be ...

310

World Energy Intensity by Region, 1970-2020  

U.S. Energy Information Administration (EIA)

If energy intensities in the developing world are assumed to increase by 136 percent—the most rapid annual rate of increase observed between 1990 and 1997 ...

311

United States - U.S. Energy Information Administration (EIA ...  

U.S. Energy Information Administration (EIA)

Energy use in homes, commercial buildings, ... Hawaii Idaho Illinois Indiana Iowa Kansas: ... data are no longer collected and are assumed to be zero.

312

United States - U.S. Energy Information Administration (EIA ...  

U.S. Energy Information Administration (EIA)

Energy use in homes, commercial ... Hawaii Idaho Illinois Indiana ... a Consumption data are no longer collected and are assumed to be zero in the ...

313

United States - U.S. Energy Information Administration (EIA ...  

U.S. Energy Information Administration (EIA)

Energy use in homes, commercial buildings, ... Hawaii Idaho Illinois Indiana Iowa Kansas: ... a Data are not collected and are assumed to be zero in ...

314

U.S. Energy Information Administration - EIA - Independent ...  

U.S. Energy Information Administration (EIA)

Energy use in homes, commercial buildings, ... Hawaii Idaho Illinois Indiana Iowa Kansas: Kentucky ... residential coal consumption is assumed to be z ...

315

The Department of Energy's Executive Order 13563 Preliminary...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

24, 2011 comments to the Notice of Data Availability on Equipment Price Forecasting in Energy Conservation Standards Analysis. 1 DOE has traditionally assumed zero learning in the...

316

U.S. Energy Information Administration (EIA) - Sector  

Gasoline and Diesel Fuel Update (EIA)

assumes that new home construction adopts the most energy-efficient components for insulation, windows, and space conditioning equipment. In the High Technology and Best...

317

China Energy Databook - Rev. 4  

E-Print Network (OSTI)

crude oil, fuel oil, and kerosene. Source: China Energynatural crude and shale oil. Source: China Energy AnnualAssumed to be crude oil. Source: Yang, 1988; Yang, 1991. IV-

Sinton Editor, J.E.

2010-01-01T23:59:59.000Z

318

BEFORE THE U.S. DEPARTMENT OF ENERGY  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Washington, D.C. 20554 Washington, D.C. 20554 In the Matter of: American Valve, Inc. (Showerheads) Case Number: 2010-C W-1411 NOTICE OF PROPOSED CIVIL PENALTY' Date issued: September 8, 2010 Number of alleged violations: Maximum possible assessment : $191,200 Proposed civil penal $29,200 y: The Office of the General Counsel of the U. S. Department of Energy (DOE) alleges tha American Valve, Inclorporated violated certain provisions of the Energy Policy and Conservation Act, 4 U.S.C. § 6201 et seq., 10 C.F.R. Part 430, or boh. Specifically, DOE al, eges: 1. American Valve, Incorporated, manufactures or privately labels a variety of showerheads in commerce in the United States of America including models: HSHH, HSSII, and HSCP. 2. These models have been in distribution in the U.S. for at least '365 days.

319

Energy conservation and official UK energy forecasts  

SciTech Connect

Behind the latest United Kingdom (UK) official forecasts of energy demand are implicit assumptions about future energy-price elasticities. Mr. Pearce examines the basis of the forecasts and finds that the long-term energy-price elasticities that they imply are two or three times too low. The official forecasts substantially understate the responsiveness of demand to energy price rises. If more-realistic price elasticities were assumed, the official forecasts would imply a zero primary energy-demand growth to 2000. This raises the interesting possibility of a low energy future being brought about entirely by market forces. 15 references, 3 tables.

Pearce, D.

1980-09-01T23:59:59.000Z

320

High-Compression-Ratio; Atkinson-Cycle Engine Using Low-Pressure Direct Injection and Pneumatic-Electronic Valve Actuation Enabled by Ionization Current and Foward-Backward Mass Air Flow Sensor Feedback  

DOE Green Energy (OSTI)

This report describes the work completed over a two and one half year effort sponsored by the US Department of Energy. The goal was to demonstrate the technology needed to produce a highly efficient engine enabled by several technologies which were to be developed in the course of the work. The technologies included: (1) A low-pressure direct injection system; (2) A mass air flow sensor which would measure the net airflow into the engine on a per cycle basis; (3) A feedback control system enabled by measuring ionization current signals from the spark plug gap; and (4) An infinitely variable cam actuation system based on a pneumatic-hydraulic valve actuation These developments were supplemented by the use of advanced large eddy simulations as well as evaluations of fuel air mixing using the KIVA and WAVE models. The simulations were accompanied by experimental verification when possible. In this effort a solid base has been established for continued development of the advanced engine concepts originally proposed. Due to problems with the valve actuation system a complete demonstration of the engine concept originally proposed was not possible. Some of the highlights that were accomplished during this effort are: (1) A forward-backward mass air flow sensor has been developed and a patent application for the device has been submitted. We are optimistic that this technology will have a particular application in variable valve timing direct injection systems for IC engines. (2) The biggest effort on this project has involved the development of the pneumatic-hydraulic valve actuation system. This system was originally purchased from Cargine, a Swedish supplier and is in the development stage. To date we have not been able to use the actuators to control the exhaust valves, although the actuators have been successfully employed to control the intake valves. The reason for this is the additional complication associated with variable back pressure on the exhaust valves when they are opened. As a result of this effort, we have devised a new design and have filed for a patent on a method of control which is believed to overcome this problem. The engine we have been working with originally had a single camshaft which controlled both the intake and exhaust valves. Single cycle lift and timing control was demonstrated with this system. (3) Large eddy simulations and KIVA based simulations were used in conjunction with flow visualizations in an optical engine to study fuel air mixing. During this effort we have devised a metric for quantifying fuel distribution and it is described in several of our papers. (4) A control system has been developed to enable us to test the benefits of the various technologies. This system used is based on Opal-RT hardware and is being used in a current DOE sponsored program.

Harold Schock; Farhad Jaberi; Ahmed Naguib; Guoming Zhu; David Hung

2007-12-31T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Valve Packing Performance Improvement: Sealing Technology and Plant Leakage Reduction Series  

Science Conference Proceedings (OSTI)

"Valve Packing Performance Improvement" is the seventh in a series of training modules addressing leakage at nuclear power plants. The first six modules in this series address: o Leakage management programs o Assembling bolted joints with spiral-wound gaskets o Preload requirements for bolted joints with spiral-wound gaskets o Lube oil system leakage mitigation o Leakage reduction from threaded joints o Leakage reduction from bolted joints with sheet gaskets

2002-03-28T23:59:59.000Z

322

Use of MCC-Based Motor Torque Measurements for Periodic Verification of Motor-Operated Valves  

Science Conference Proceedings (OSTI)

This report develops, justifies, and validates a motor control center- (MCC-) based motor torque periodic verification (MTPV) method for torque-switch-controlled closing strokes of rising stem motor-operated valves (MOVs) with ac motors. The report details the evaluation of motor torque data obtained from electrical measurements at the MCC and covers the use of these (and other) measurements in MOV periodic verification (PV) testing.

2006-03-30T23:59:59.000Z

323

Nuclear Maintenance Applications Center: Air-Operated Valve Maintenance Guide: Revision 2  

Science Conference Proceedings (OSTI)

An increased awareness of the importance of air-operated valves (AOVs) has led to progressively more sophisticated maintenance practices within the nuclear industry. Nonnuclear plants are also heavily dependent on reliable AOV operation. The dynamic method used by fossil power plants to satisfy transient electrical demands places additional stress on plant components, including AOVs. Therefore, there is a growing need for standardized technical guidance related to AOVs. The Electric Power Research Instit...

2008-12-18T23:59:59.000Z

324

Valve-Regulated Lead Acid (VRLA) Battery Seismic Testing: Initial Investigation  

Science Conference Proceedings (OSTI)

This report describes the results obtained when subjecting naturally aged valve-regulated lead acid (VRLA) batteries from two manufacturers to the capacity test, seismic test, and final capacity test described in IEEE Standard 535- 2006, Standard for Qualification of Class 1E Lead Storage Batteries for Nuclear Power Generating Stations. The project that is the subject of this report was not intended to be a formal qualification program or process. Instead, it was a test of the seismic ruggedness of ...

2013-04-12T23:59:59.000Z

325

Technical Repair Guidelines for Limitorque Model SMB-000 Valve Actuators: Revision 1  

Science Conference Proceedings (OSTI)

This technical repair guide (TRG) for Limitorque motor-operated valve (MOV) actuator model SMB-000 is the first in a series of documents devoted to the comprehensive maintenance and repair of Limitorque actuators. This guide provides instructions for engineering, operations, and maintenance personnel on MOV actuator repair, maintenance, adjustment, and troubleshooting methods. Originally published in 1989, this document has now been thoroughly revised (Revision 1) to incorporate new information and techn...

1994-10-02T23:59:59.000Z

326

Hydraulic waste energy recovery, Phase 2. A technical report  

SciTech Connect

The energy required for booster station operation is supplied by the electrical utility company and has an associated cost. Energy removed by pressure reducing valves in the system is lost or wasted. The objective of this project is to capture the wasted hydraulic energy with in-line turbines. In this application, the in-line turbines act as pressure reducing valves while removing energy from the water distribution system and converting it to electrical energy. The North Service Center pumping station was selected for the pilot program due to the availability of a wide range in pressure drop and flow, which are necessary for hydraulic energy recovery. The research performed during this project resulted in documentation of technical, economic, installation, and operational information necessary for local government officials to make an informed judgement as it relates to in-line turbine generation.

1992-02-01T23:59:59.000Z

327

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

41 - 4550 of 31,917 results. 41 - 4550 of 31,917 results. Download Cooling Tower Report, October 2008 http://energy.gov/oe/downloads/cooling-tower-report-october-2008 Article Old Man Winter Defied by High-Tech Snowplows Lake County, Illinois keeps the streets clear and saves money thanks to the addition of GPS technology to their snowplow fleet. http://energy.gov/articles/old-man-winter-defied-high-tech-snowplows Download DOE-SPEC-3019-96 DOE Specification, Valve-Regulated Type Lead-Acid Storage Batteries Canceled, Effective October 2001, due to FY 2001 Sunset Review This specification defines requirements for sealed valve-regulated type, lead-acid storage batteries and accessory equipment for [general purpose] [uninterruptible power supply (UPS)] http://energy.gov/hss/downloads/doe-spec-3019-96

328

On the Chemical Potential of Dark Energy  

E-Print Network (OSTI)

It is widely assumed that the observed universe is accelerating due to the existence of a new fluid component called dark energy. In this article, the thermodynamics consequences of a nonzero chemical potential on the dark energy component is discussed with special emphasis to the phantom fluid case. It is found that if the dark energy fluid is endowed with a negative chemical potential, the phantom field hypothesis becomes thermodynamically consistent with no need of negative temperatures as recently assumed in the literature.

S. H. Pereira

2008-06-23T23:59:59.000Z

329

Radiant energy receiver having improved coolant flow control means  

DOE Patents (OSTI)

An improved coolant flow control for use in radiant energy receivers of the type having parallel flow paths is disclosed. A coolant performs as a temperature dependent valve means, increasing flow in the warmer flow paths of the receiver, and impeding flow in the cooler paths of the receiver. The coolant has a negative temperature coefficient of viscosity which is high enough such that only an insignificant flow through the receiver is experienced at the minimum operating temperature of the receiver, and such that a maximum flow is experienced at the maximum operating temperature of the receiver. The valving is accomplished by changes in viscosity of the coolant in response to the coolant being heated and cooled. No remotely operated valves, comparators or the like are needed.

Hinterberger, H.

1980-10-29T23:59:59.000Z

330

CX-002934: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

934: Categorical Exclusion Determination 934: Categorical Exclusion Determination CX-002934: Categorical Exclusion Determination Energy Efficiency and Conservation Block Grant Program: Small Cities and Counties Initiative (Subgrant): Leitchfield Anaerobic Digester CX(s) Applied: A9 Date: 07/07/2010 Location(s): Leitchfield, Kentucky Office(s): Energy Efficiency and Renewable Energy, Golden Field Office The Kentucky Department for Energy Development and Independence is planning to award $125,000 in Energy Efficiency and Conservation Block Grant (EECBG) American Recovery and Reinvestment Act funding to the City of Leitchfield in conjunction with Grayson County to design gas lines and valves. The gas lines and valves will be used to transport methane created by a proposed anaerobic digester at the wastewater treatment plant to a food processing

331

CX-004443: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

43: Categorical Exclusion Determination 43: Categorical Exclusion Determination CX-004443: Categorical Exclusion Determination State Energy Program - Combined Heat and Power - Metropolitan Council CX(s) Applied: B5.1 Date: 11/16/2010 Location(s): Minnesota Office(s): Energy Efficiency and Renewable Energy, Golden Field Office The Metropolitan Council Environmental Services is proposing to use $200,000 in State Energy Program funding for the installation of a 750 kilowatt non-condensing steam turbine generator in the Solids Management Building at the Metro Wastewater Treatment Plant (WWTP). Currently, the steam is sent to either an existing 4 megawatt condensing steam turbine generator or a set of pressure reducing valves. The pressure drop results in a loss of energy across the pressure reducing valves. Installation of

332

Controlling electrical costs with energy management  

SciTech Connect

Energy Management Systems have been proven to be extremely effective in reducing electrical energy costs. This particular system is also capable of monitoring natural gas usage and even regulating that usage with the control of valves. Controlling electrical energy usage must be a cooperative effort between the plant where the system is to be installed and the manufacturer of the Energy Management Controller. The latter can be assisted by being advised of which loads are able to be shed and how shedding those loads affect production.

Collins, W.M.

1984-07-01T23:59:59.000Z

333

Regionalized Global Energy Scenarios Meeting Stringent Climate Targets  

E-Print Network (OSTI)

to generate the energy supply mix that would meet given energy demands at lowest cost, assuming strongRegionalized Global Energy Scenarios Meeting Stringent Climate Targets ­ cost effective fuel in the energy system it is less costly to reduce CO2-emissions #12;Global energy system model #12;Global energy

334

Energy Efficient Technologies  

NLE Websites -- All DOE Office Websites (Extended Search)

Energy Efficient Technologies Energy Efficient Technologies Energy efficient technologies are available now! Many of the vehicles currently on display in dealer showrooms boast new performance-enhancing, fuel-saving technologies that can save you money. Engine Technologies Transmission Technologies All Engine Technology Average Efficiency Increase Variable Valve Timing & Lift improve engine efficiency by optimizing the flow of fuel & air into the engine for various engine speeds. 5% Cylinder Deactivation saves fuel by deactivating cylinders when they are not needed. 7.5% Turbochargers & Superchargers increase engine power, allowing manufacturers to downsize engines without sacrificing performance or to increase performance without lowering fuel economy. 7.5% Integrated Starter/Generator (ISG) Systems automatically turn the engine on/off when the vehicle is stopped to reduce fuel consumed during idling. 8%

335

Improvement in both giant magnetoresistance and exchange bias through hydrogen ion irradiation at low energy  

SciTech Connect

Irradiation of IrMn-based spin valves with 550 eV hydrogen ions increased their giant magnetoresistance and exchange bias by 20% and 60%, respectively. This significant enhancement stems from the strong (111) texture and small mosaic spread of the IrMn antiferromagnet that resulted from the microstructural reconstruction caused by the energy transfer during the bombardment by hydrogen ions, as well as by the narrow dispersion in the exchange bias. Irradiation with the hydrogen ion at low energy can improve the properties of spin valves without resulting in undue degradation in the performance or the microstructure.

Shim, Jaechul; Han, Yoonsung; Lee, Jinwon; Hong, Jongill [Materials Science and Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of)

2008-09-01T23:59:59.000Z

336

Magnetism reflectometer study shows LiF layers improve efficiency in spin valve devices  

Science Conference Proceedings (OSTI)

New, more efficient materials for spin valves - a device used in magnetic sensors, random access memories, and hard disk drives - may be on the way based on research using the magnetism reflectometer at Oak Ridge National Laboratory (ORNL). Spin valve devices work by means of two or more conducting magnetic material layers that alternate their electrical resistance depending on the layers alignment. Giant magnetoresistance is a quantum mechanical effect first observed in thin film structures about 20 years ago. The effect is observed as a significant change in electrical resistance, depending on whether the magnetization of adjacent ferromagnetic layers is in a parallel or an antiparallel magnetic alignment. 'What we are doing here is developing new materials. The search for new materials suitable for injecting and transferring carriers with a preferential spin orientation is most important for the development of spintronics,' said Valeria Lauter, lead instrument scientist on the magnetism reflectometer at the Spallation Neutron Source (SNS), who collaborated on the experiment. The researchers discovered that the conductivity of such materials is improved when an organic polymer semiconductor layer is placed between the magnetic materials. Organic semiconductors are now the material of choice for future spin valve devices because they preserve spin coherence over longer times and distances than conventional semiconductors. While research into spin valves has been ongoing, research into organic semiconductors is recent. Previous research has shown that a 'conductivity mismatch' exists in spin valve systems in which ferromagnetic metal electrodes interface with such organic semiconductors as Alq3 ({pi}-conjugated molecule tris(8-hydroxy-quinoline) aluminium). This mismatch limits the efficient injection of the electrons from the electrodes at the interface with the semiconductor material. However, lithium fluoride (LiF), commonly used in light-emitting diodes, has been found to enhance the injection of electrons through the semiconductor. Researchers from the University of Alabama and ORNL used polarized neutrons at the magnetism reflectometer at SNS to investigate the electronic, magnetic, and structural properties of the electrodes in a novel system. In this system, the magnetic layers cobalt and Ni{sub 80}Fe{sub 20} are interfaced with spacer layers composed of the organic semiconductor Alq3. A coupling layer of LiF is inserted to separate the magnetized layers from the semiconductor. 'ALQ3 is an organic semiconductor material,' said Lauter. 'Normally in these systems a first magnetic layer is grown on a hard substrate so that one can get the controlled magnetic parameters. Then you grow the organic semiconductor layer, followed by another magnetic material layer, such as cobalt.' In addition to determining the effect of the LiF layers on the efficiency of the electron injection, the researchers wanted to determine the magnetic properties of the cobalt and Ni{sub 80}Fe{sub 20} as well as the interfacial properties: whether there is interdiffusion of cobalt through the LiF layer to the semiconductor, for example. The researchers used polarized neutrons at beam line 4A to probe the entire, layer-by-layer assembly of the system. 'Reflectometry with polarized neutrons is a perfect method to study thin magnetic films,' Lauter said. 'These thin films - if you put one on a substrate, you see it just like a mirror. However, this mirror has a very complicated internal multilayer structure. The neutrons look inside this complicated structure and characterize each and every interface. Due to the depth sensitivity of the method, we measure the structural and magnetic properties of each layer with the resolution of 0.5 nm. The neutron scattering results found that inserting LiF as a barrier significantly improves the quality of the interface, increasing the injection of electrons from the magnetic layer through the organic semiconductor in the spin valve and enhancing the overall properties of the system. In related work the magneti

Bardoel, Agatha A [ORNL; Lauter, Valeria [ORNL; Szulczewski, Greg J [ORNL

2012-01-01T23:59:59.000Z

337

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

91 - 16900 of 26,764 results. 91 - 16900 of 26,764 results. Download CX-006251: Categorical Exclusion Determination Big Hill Heat Exchanger Isolation Valves - Install CX(s) Applied: B1.3 Date: 06/20/2011 Location(s): Jefferson County, Texas Office(s): Strategic Petroleum Reserve Field Office http://energy.gov/nepa/downloads/cx-006251-categorical-exclusion-determination Download CX-006252: Categorical Exclusion Determination Big Hill Heat Exchanger Isolation Valves GFE CX(s) Applied: B1.3 Date: 06/20/2011 Location(s): Jefferson County, Texas Office(s): Strategic Petroleum Reserve Field Office http://energy.gov/nepa/downloads/cx-006252-categorical-exclusion-determination Page Categorical Exclusion Determinations: B5.23 B5.23: Electric vehicle charging stationsThe installation, modification,

338

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

31 - 14040 of 29,416 results. 31 - 14040 of 29,416 results. Download DOE-SPEC-3019-96 DOE Specification, Valve-Regulated Type Lead-Acid Storage Batteries Canceled, Effective October 2001, due to FY 2001 Sunset Review This specification defines requirements for sealed valve-regulated type, lead-acid storage batteries and accessory equipment for [general purpose] [uninterruptible power supply (UPS)] http://energy.gov/hss/downloads/doe-spec-3019-96 Download CX-006855: Categorical Exclusion Determination Rocket Centrifuge Removal (Eastern Side of TA-II) CX(s) Applied: B1.23 Date: 09/12/2011 Location(s): Albuquerque, New Mexico Office(s): NNSA-Headquarters, Golden Field Office http://energy.gov/nepa/downloads/cx-006855-categorical-exclusion-determination Download Microsoft Word- acqguide18pt0 Nov 2010

339

Combustion, Control, and Fuel Effects in a Spark Assisted HCCI Engine Equipped with Variable Valve Timing  

SciTech Connect

Widespread implementation of homogeneous charge compression ignition (HCCI) engines is presently hindered by stability, control, and load range issues. Although the operable HCCI speed/load range is expanding, it is likely that the initial HCCI engines will rely on conventional combustion for part of the operating cycle. In the present study, we have investigated the role of fuel properties and chemistry on the operation of a spark-assisted gasoline HCCI engine. The engine employed is a single cylinder, 500 cc, port fuel injected research engine, operating near lambda = 1.0 and equipped with hydraulic variable valve actuation. HCCI is initiated by early exhaust valve closing to retain exhaust in the cylinder, thereby increasing the cylinder gas temperature. This is also referred to as a 'negative overlap' strategy. A total of 10 custom blended gasolines and three different batches of indolene from two suppliers were run at 5 speed-load combinations and performance was characterized by timing sweeps. Within the quality of the data set, we can say the all fuels provided equivalent combustion and performance characteristics when compared at the same combustion phasing. The fuels did, however, require different degrees of retained exhaust as measured by exhaust valve closing angle to achieve the same combustion phasing. Fuels with higher octane sensitivity were found to ignite more easily or more quickly and to burn more quickly than fuels with lower octane sensitivity. This is an expected result since the engine is naturally aspirated and operates with high compression temperatures due to the high retained exhaust fraction and recompression.

Bunting, Bruce G [ORNL

2006-01-01T23:59:59.000Z

340

Ocean tide energy converter  

Science Conference Proceedings (OSTI)

A tide motor energy source includes a tidal piston with a valved chamber. The piston drives a hydraulic ram to generate electrical power through a pressure accumulator and hydraulic motor. The ram can be locked hydraulically to enable the tidal piston to be held fixed at a desired elevation and the valves in the chamber permit it to be filled with water or air. The piston with its chamber filled with air at its low tide position and then released for controlled ascent while submerged acts as a submerged float for driving the ram upwardly while the tide runs in during one phase of its operation. The piston with its chamber filled with water while locked at its highest position as the tide begins to run out, and then released to fall under control, acts as a weight suspended in air after the water level drops below the piston for driving the ram downwardly during the second phase of its operation. The rising and falling motion of the tidal piston is used as the energy source.

Rainey, D.E.

1980-06-24T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Imaging of lateral spin valves with soft x-ray microscopy  

SciTech Connect

We investigated Co/Cu lateral spin valves by means of high-resolution transmission soft x-ray microscopy with magnetic contrast that utilizes x-ray magnetic circular dichroism (XMCD). No magnetic XMCD contrast was observed at the Cu L{sub 3} absorption edge, which should directly image the spin accumulation in Cu. Although electrical transport measurements in a non-local geometry clearly detected the spin accumulation in Cu, which remained unchanged during illumination with circular polarized x-rays at the Co and Cu L{sub 3} absorption edges.

Mosendz, O.; Mihajlovic, G.; Pearson, J. E.; Fischer, P.; Im, M.-Y.; Bader, S. D.; Hoffmann, A.

2009-05-01T23:59:59.000Z

342

Reviews of ASME Section 11 pump and valve relief requests: Post Generic Letter 89-04  

SciTech Connect

This paper presents a discussion of ASME Section 11 Pump and Valve Inservice Testing relief request reviews by the NRC and their contractors. Topics that will be discussed include the scope of USNRC reviews in Technical Evaluation Reports (TERs) (and Safety Evaluation, SEs); including the basis for granting relief requests, the status of relief requests in IST Program updates, and the Generic Letter 89-04 approval process; and the level of technical detail required in submitted programs. This presentation is based on the experiences of Brookhaven National Laboratory in reviewing IST Programs for the Mechanical Engineering Branch of the US Nuclear Regulatory Commission.

DiBiasio, A.

1992-07-01T23:59:59.000Z

343

Reviews of ASME Section 11 pump and valve relief requests: Post Generic Letter 89-04  

SciTech Connect

This paper presents a discussion of ASME Section 11 Pump and Valve Inservice Testing relief request reviews by the NRC and their contractors. Topics that will be discussed include the scope of USNRC reviews in Technical Evaluation Reports (TERs) (and Safety Evaluation, SEs); including the basis for granting relief requests, the status of relief requests in IST Program updates, and the Generic Letter 89-04 approval process; and the level of technical detail required in submitted programs. This presentation is based on the experiences of Brookhaven National Laboratory in reviewing IST Programs for the Mechanical Engineering Branch of the US Nuclear Regulatory Commission.

DiBiasio, A.

1992-01-01T23:59:59.000Z

344

Combined cycle electric power plant with a steam turbine having a sliding pressure main bypass and control valve system  

SciTech Connect

A combined cycle electric power plant includes two gas turbines, a steam turbine, and a digital control system with an operator analog or manual backup. Each of the gas turbines has an exhaust heat recovery steam generator connected to a common header from which the steam is supplied by one or both of the steam generators for operating the steam turbine. The control system is of the sliding pressure type and maintains a predetermined steam pressure as a function of steam flow according to a predetermined characterization depending on the number of steam generators in service to limit the maximum steam velocity through the steam generators, and reduce the probability of water carryover into the steam turbine. Such control is always maintained by the bypass valve. The turbine control valve responds to the speed/load demand only, except when the bypass valve is closed and the rate of steam generation is insufficient to maintain a predetermined pressure flow relationship.

Uram, R.

1980-05-06T23:59:59.000Z

345

A visual inspection system for evaluating the interior surface of valve stems on material storage container tops  

SciTech Connect

A nondestructive inspection for evaluating the interior surface of the small diameter valve stems on material storage container tops was mandated. The specifications required that the interior surface of the valve stem have a surface finish of {number sign}16 or better. Conventional methods which utilizes mechanical stylus-type''surface analyzing equipment could not extend into the narrow 0.312 inch diameter by 1.5 inch deep hole (of the valve stem). A visual inspection system which exploits the capabilities of a high resolution fiberoptic borescope was designed and assembled to resolve this requirement. This paper discusses the design and inspection features of the aforementioned system and includes several illustrations of inspection results. 6 figs.

Pickett, C.A.

1990-12-01T23:59:59.000Z

346

A characterization of check valve degradation and failure experience in the nuclear power industry: 1991 Failures, Volume 2  

SciTech Connect

Review and characterization of check valve failures taken from the Institute of Nuclear Power Operation`s Nuclear Plant Reliability Data System was performed in accordance with part two of a three-phase project sponsored by the US Nuclear Regulatory Commission. The analysis was performed for check valve failures occurring in 1991 and is intended to update the previous analysis performed for the time period 1984--1990. To maintain consistency and for ease of the 1991 analysis presents the same parameters and cross-correlations in essentially the same format as the 1984--1990 study. Additional data was obtained for the 1991 analysis, including information related to specific check valve type. This information is presented in a separate section of the report.

McElhaney, K.L. [Oak Ridge National Lab., TN (United States)

1995-07-01T23:59:59.000Z

347

Maryland - U.S. Energy Information Administration (EIA) - U.S ...  

U.S. Energy Information Administration (EIA)

Energy use in homes, commercial buildings, ... Hawaii Idaho Illinois Indiana Iowa Kansas: ... data are no longer collected and are assumed to be zero.

348

Commercial Building Energy Asset Score Program  

NLE Websites -- All DOE Office Websites (Extended Search)

Savings1 28% Current Score 62 2 Modeled energy use assumes typical operating and normal weather conditions as defined in the Model Assumptions for this Building Type. 1 The...

349

UC International Programs 1) UNDERSTANDING AND ASSUMING RISKS  

E-Print Network (OSTI)

of design, safety and maintenance of utilities, including computing facilities, buildings, public places or omissions of, any host institution, host family, transportation carrier, hotel, tour organizer, or other) fare changes, dishonors of hotel, airline or vehicle rental reservations; (4) any delays or missed

Papautsky, Ian

350

BEFORE THE U.S. DEPARTMENT OF ENERGY WASHINGTON, D.C.  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

American Valve, Inc. American Valve, Inc. Respondent ORDER Issued : October 4, 2010 By the General Counsel, U.S. Department of Energy: Case Number : 2010-C W-1411 1. In this Order, I adopt the attached Compromise Agreement entered into between the U.S. Department of Energy ("DOE") and American Valve, Inc. ("Respondent"). The Compromise Agreement resolves the case initiated to pursue a civil penalty for violations of the compliance certification requirements at 10 C.F.R. § 430.62. 2. The DOE and Respondent have negotiated the terms of the Compromise Agreement that resolve this matter . A copy of the Compromise Agreement is attached hereto and incorporated by reference. 3. After reviewing the terms of the Compromise Agreement and evaluating the facts before me, I find that the public interest would be served by adopting the

351

Energy Conversion, Mixing Energy, and Neutral Surfaces with a Nonlinear Equation of State  

E-Print Network (OSTI)

Energy Conversion, Mixing Energy, and Neutral Surfaces with a Nonlinear Equation of State JONAS energy, it is generally assumed that it does not produce a restoring buoyancy force. However, it is here effect) such a neutral displacement is accompanied by a conversion between internal energy E

Nycander, Jonas

352

Motor-operated valve reliability programs: Lessons learned to meet new NRC (Nuclear Regulatory Commission) requirements  

Science Conference Proceedings (OSTI)

In recent years, reliability problems have surfaced with power plant motor-operated valves (MOVs) that (a) fail to perform as designed, and/or (b) require excessive maintenance to perform their intended function. As a result, the US Nuclear Regulatory Commission (NRC) mandated certain testing and reporting requirements in inspection and enforcement bulletin 85-03 (85-03). The NRC's generic letter 89-10 (89-10) significantly expands these requirements, to include all safety-related and position-changeable MOVs. The MOV program experience at the Sacramento Municipal Utility District (SMUD) Rancho Seco plant is particularly valuable since the NRC, to a large extent, utilized this program as the prototype for 89-10's requirements. The MOV inspection, overhaul, and testing began in September 1986, with completion scheduled for December 1986. The paper discusses problems encountered, recovery plant, results of recovery planning, and lessons learned. Experience at Rancho Seco has shown that comprehensive valve programs incorporating appropriate design practices, preventive maintenance practices, and operational constraints can improve plant availability.

Anderson, M.W.; Fadel, D.P.; Fraser, P.J.

1990-06-01T23:59:59.000Z

353

Engine cooling system air venting arrangement with buoyant air purge valve  

Science Conference Proceedings (OSTI)

An air vent arrangement is described for the cooling system of an automotive type engine having a radiator with a coolant inlet. The engine has coolant passages communicating with the radiator through an outlet essentially horizontally disposed, tubing connecting the radiator inlet and coolant outlet, and a thermostat in the outlet horizontally movable to open and closed positions. A horizontally disposed air bleed bypass passage is located vertically above the thermostat connecting the coolant outlet to a portion of the tubing downstream of the thermostat bypassing the same when the thermostat is in a closed position for bleeding air from the cooling system. The bypass passage has a valve therein moveable between a position blocking flow of coolant through the same and a second position opening the passage permitting the bleed of air therethrough. The valve is buoyant and constructed and arranged to pivot from a non flowblocking air bleed position into a flow blocking position in response to flow of coolant into the bypass passage acting thereagainst.

Schnizlein, M.E.

1987-02-17T23:59:59.000Z

354

International Energy Outlook 2006  

Gasoline and Diesel Fuel Update (EIA)

Key Assumptions for the IEO2006 Kyoto Protocol Case Energy-Related Emissions of Greenhouse Gases The System for the Analysis of Global energy Markets (SAGE)-the model used by EIA to prepare the IEO2006 mid-term projections-does not include non-energy- related emissions of greenhouse gases, which are esti- mated at about 15 to 20 percent of total greenhouse gas emissions, based on inventories submitted to the United Nations Framework Convention on Climate Change (UNFCCC). SAGE models global energy supply and demand and, therefore, does not address agricultural and other non-energy-related emissions. EIA implicitly assumes that percentage reductions of non-energy-related emissions and their associated abatement costs will be similar to those for energy- related emissions. Non-energy-related greenhouse gas emissions are likely to grow faster than energy-related

355

Energy Service Companies | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Service Companies Service Companies Energy Service Companies October 7, 2013 - 1:43pm Addthis Energy service companies (ESCOs) develop, install, and fund projects designed to improve energy efficiency and reduce operation and maintenance costs in their customers' facilities. ESCOs generally act as project developers for a wide range of tasks and assume the technical and performance risk associated with the project. ESCOs are set apart from other firms that offer energy-efficiency improvements by performance-based contracting. When an ESCO undertakes a project, the company's compensation is directly linked to the cost savings from energy actually saved. The comprehensive energy-efficiency retrofits inherent in energy service company projects typically require a large initial capital investment and

356

4-80 Two rigid tanks connected by a valve to each other contain air at specified conditions. The volume of the second tank and the final equilibrium pressure when the valve is opened are to be determined.  

E-Print Network (OSTI)

. Treating air as an ideal gas, the volume of the second tank and the mass of air in the first tank temperatures and pressures in ideal gas calculations. Using gage pressures would result in pressure drop of 04-40 4-80 Two rigid tanks connected by a valve to each other contain air at specified conditions

Bahrami, Majid

357

Home Energy Saver  

NLE Websites -- All DOE Office Websites (Extended Search)

Glossary Glossary Heating, Ventilation and Cooling Terminology System Capacity System capacity is a measurement of the total amount of heat or cooling the furnace, heat pump or air conditioner can produce in one hour. This amount is reported in Btu/hr on the nameplate of the equipment. Btu Btu, short for British Thermal Unit is a unit of heat energy. One Btu is the amount of heat needed to raise the temperature of one pound of water 1°F. To get a rough idea of how much heat energy this is, the heat given off by burning one wooden kitchen match is approximately one Btu. AFUE The AFUE, or Annualized Fuel Utilization Efficiency, is the ratio of the total useful heat the gas furnace delivers to the house to the heat value of the fuel it consumes. Heat Pump A heat pump is basically an air conditioner with a reversible valve

358

Annual Energy Outlook 2000 - Overview  

Gasoline and Diesel Fuel Update (EIA)

Homepage Homepage Key Issues Prices Consumption Energy Intensity Electricity Generation Production and Imports Carbon Emissions Key Issues Important energy issues addressed in the Annual Energy Outlook 2000 (AEO2000) include, among others, the ongoing restructuring of U.S. electricity markets, near-term prospects for world oil markets, and the impacts of energy use on carbon emissions. AEO2000 reflects the restructuring of U.S. electricity markets and the shift to increased competition by assuming changes in the financial structure of the industry. Ongoing efficiency and operating improvements are also assumed to continue. The projections assume a transition to full competitive pricing in States with specific deregulation plans—California, New York, New England, the Mid-Atlantic States, Illinois, Texas, Michigan, Ohio, Arizona, and New Mexico. Other States are assumed to continue cost-of-service electricity pricing. The provisions of the California legislation regarding stranded cost recovery and price caps are included. In other regions, stranded cost recovery is assumed to be phased out by 2008.

359

Modeling and optimizing passive valve designs for the implantable Gold Micro-Shunt used in glaucoma treatment  

Science Conference Proceedings (OSTI)

Glaucoma is an age-related eye disease that causes ocular nerve damage, typically characterized by elevated intraocular pressure (IOP). Studies have shown that IOP can vary significantly on the order of days or even hours. Failure to control IOP spikes ... Keywords: Check-valve, Drainage device, Finite element analysis, Glaucoma, Intraocular pressure, MEMS

Judy L. Lin; Jason M. Clevenger

2009-06-01T23:59:59.000Z

360

A MEMS Thin Film AlN Supercritical Carbon Dioxide Valve  

E-Print Network (OSTI)

When a piezoelectric material converts mechanical energy tothis, for piezoelectric actuators, an electrical energy willthe piezoelectric material to generate a mechanical energy

Chen, Ya-Mei

2011-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Brane-Bulk energy exchange and agegraphic dark energy  

E-Print Network (OSTI)

We consider the agegraphic models of dark energy in a braneworld scenario with brane-bulk energy exchange. We assume that the adiabatic equation for the dark matter is satisfied while it is violated for the agegraphic dark energy due to the energy exchange between the brane and the bulk. Our study shows that with the brane-bulk interaction, the equation of state parameter of agegraphic dark energy on the brane, $w_D$, can have a transition from normal state where $w_D >-1 $ to the phantom regime where $w_D energy always satisfies $w^{\\mathrm{eff}}_D\\geq-1$.

Ahmad Sheykhi

2009-08-09T23:59:59.000Z

362

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

41 - 9850 of 26,764 results. 41 - 9850 of 26,764 results. Download CX-005481: Categorical Exclusion Determination Grant for State Sponsored Renewable Energy and Energy Efficiency Projects - Montclair State University Solar Farm CX(s) Applied: B5.1 Date: 03/29/2011 Location(s): Montclair, New Jersey Office(s): Energy Efficiency and Renewable Energy, National Energy Technology Laboratory http://energy.gov/nepa/downloads/cx-005481-categorical-exclusion-determination Download CX-005813: Categorical Exclusion Determination Fire Department Personnel to Perform Annual Flush of Hydrants and Prove Curb Valves CX(s) Applied: B1.3 Date: 03/29/2011 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office http://energy.gov/nepa/downloads/cx-005813-categorical-exclusion-determination

363

Carmine Difiglio | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Carmine Difiglio Carmine Difiglio About Us Carmine Difiglio - Deputy Director for Energy Security Carmine Difiglio Dr. Carmine Difiglio serves as Deputy Director for Energy Security, Office of Energy Policy and Systems Analysis (EPSA). In this capacity, Dr. Difiglio provides the Director of EPSA and the Secretary of Energy policy analysis, analytic support, and policy advice concerning U.S. energy security, including energy supply and demand, energy markets, long-term strategies to enhance U.S. energy security, and preparing for, or responding to, energy market disruptions and energy emergencies. Prior to assuming this position, Dr. Difiglio served as Deputy Assistant Secretary for Policy Analysis at the U.S. Department of Energy and Head of Technology Policy at the International Energy Agency. His work and

364

Investigation Of Adhesion Formation In New Stainless Steel Trim Spring Operated Pressure Relief Valves  

SciTech Connect

Examination of proof test data for new (not previously installed) stainless steel (SS) trim spring operated pressure relief valves (SOPRV) reveals that adhesions form between the seat and disc in about 46% of all such SOPRV. The forces needed to overcome these adhesions can be sufficiently large to cause the SOPRV to fail its proof test (FPT) prior to installation. Furthermore, a significant percentage of SOPRV which are found to FPT are also found to ''fail to open'' (FTO) meaning they would not relief excess pressure in the event of an overpressure event. The cases where adhesions result in FTO or FPT appear to be confined to SOPRV with diameters < 1 in and set pressures < 150 psig and the FTO are estimated to occur in 0.31% to 2.00% of this subpopulation of SS trim SOPRV. The reliability and safety implications of these finding for end-users who do not perform pre-installation testing of SOPRV are discussed.

Savannah River Site (SRS), Aiken, SC (United States); Villanova University, Villanova, PA (United States); exida, Sellersville, PA (United States)

2013-04-16T23:59:59.000Z

365

Performance Evaluation of Hot Water Efficiency Plumbing System Using Thermal Valve  

E-Print Network (OSTI)

In Korea two popular water distribution systems—the branch type and the separate type systems—have serious drawbacks. The branch type suffers from temperature instability while the separate type suffers from excessive piping. Neither of them re-circulates water. The system proposed in this paper utilizes a water-conserving piping system with a thermostat valve. This paper compares the proposed system with that of the separate type. Our findings show that the proposed system wastes less water. After re-circulating for 78-87 seconds, water is available at set point temperature (40°C). Also, when multiple water taps are in use, the average temperature deviation is less than 0.6°C. Moreover, the proposed system has 50% less flow rate than the separate type system.

Cha, K. S.; Park, M. S.; Seo, H. Y.

2010-08-01T23:59:59.000Z

366

Irradiation-controlled giant magnetoresistance of PtMn-based spin valve  

Science Conference Proceedings (OSTI)

He{sup +}-ion irradiation resulted in the direct ordering of PtMn without postannealing. Samples were irradiated with 2 MeV He{sup +} ions and a beam current of 1.08 {mu}A/cm{sup 2} such that the corresponding surface temperature was 190 deg. C. The exchange bias direction was set in situ during irradiation in a field of 900 Oe. A high giant magnetoresistance (GMR) ratio of 11% was obtained in PtMn-based spin valves after He{sup +} irradiation. The GMR is completely eliminated after it is irradiated with oxygen ions at 42 keV. Combining He{sup +} with oxygen-ion irradiation can provide magnetic patterning for GMR sensors.

Huang, S.-H.; Lai, C.-H.; Chiang, C. C.; Yang, C.-H. [Department of Materials Science and Engineering, National Tsing Huang University, 101, Section 2, Kuang Fu Road, Hsinchu, Taiwan 30013 (China)

2006-04-15T23:59:59.000Z

367

Energy Management of Steam Distribution Systems Through Energy Audits and Computerized Reporting Programs  

E-Print Network (OSTI)

"This presentation will highlight the economic losses associated with steam distribution systems and how to establish good energy management programs to reduce energy cost by 15 to 25 percent. Recognizing energy losses in steam systems involves: 1. Steam lost through defective valves, fittings and traps. 2. Loss through damaged or inefficient insulation. 3. Energy loss through misapplication of steam traps and improper piping practices. Energy management programs will cover steam energy auditing and computerized reporting systems that are proven methods of conserving energy and substantially reducing costs. Typical savings of a facility with 1,000 traps could exceed $300,000.00 annually. The use of computerized reporting systems can be a valuable tool in establishing good energy management practices and preventive maintenance programs. The reasons why, and the methods of how a computer aided preventive maintenance program can be established will be presented "

Rivers, N.; Mandzuk, N.

1988-09-01T23:59:59.000Z

368

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

091 - 22100 of 28,905 results. 091 - 22100 of 28,905 results. Download CX-006252: Categorical Exclusion Determination Big Hill Heat Exchanger Isolation Valves GFE CX(s) Applied: B1.3 Date: 06/20/2011 Location(s): Jefferson County, Texas Office(s): Strategic Petroleum Reserve Field Office http://energy.gov/nepa/downloads/cx-006252-categorical-exclusion-determination Download CX-006039: Categorical Exclusion Determination Ohio Advanced Transportation Partnership: Zanesville Energy Biogas Compressed Natural Gas Fueling Infrastructure Date: 06/09/2011 Location(s): Zanesville, Ohio Office(s): Energy Efficiency and Renewable Energy, National Energy Technology Laboratory http://energy.gov/nepa/downloads/cx-006039-categorical-exclusion-determination Download CX-005942: Categorical Exclusion Determination

369

The analysis and specification of large high-pressure, high-temperature valves for combustion turbine protection in second-generation PFB power plants: Topical report  

SciTech Connect

The purpose of this study was to provide a specification for the high-pressure/high-temperature valves for turbine overspeed protection in a commercial-scale second-generation pressurized fluidized bed combustion (PFBC) power plant. In the event of a loss of external (generator) load, the gas turbine rapidly accelerates from its normal operating speed. Protection from excessive overspeed can be maintained by actuation of fuel isolation and air bypass valves. A design specification for these valves was developed by analyses of the turbine/compressor interaction during a loss of load and analyses of pressure and flow transients during operation of the overspeed protection valves. The basis for these analyses was the Phase 1 plant conceptual design prepared in 1987.

1994-08-01T23:59:59.000Z

370

Proceedings of the Third NRC/ASME Symposium on Valve and Pump Testing. Session 1A--Session 2C: Volume 1  

Science Conference Proceedings (OSTI)

The 1994 Symposium on Valve and Pump Testing, jointly sponsored by the Board of Nuclear Codes and Standards of the American Society of Mechanical Engineers and by the Nuclear Regulatory Commission, provides a forum for the discussion of current programs and methods for inservice testing and motor-operated valve testing at nuclear power plants. The symposium also provides an opportunity to discuss the need to improve that testing in order to help ensure the reliable performance of pumps and valves. The participation of industry representatives, regulators, and consultants results in the discussion of a broad spectrum of ideas and perspectives regarding the improvement of inservice testing of pumps and valves at nuclear power plants. This document, Volume 1, covers sessions 1A through session 2C. The individual papers have been cataloged separately.

Not Available

1994-07-01T23:59:59.000Z

371

Proceedings of the Third NRC/ASME Symposium on Valve and Pump Testing. Volume 2, Session 3A--Session 4B  

SciTech Connect

The 1994 Symposium on Valve and Pump Testing, jointly sponsored by the Board of Nuclear Codes and Standards of the American Society of Mechanical Engineers and by the Nuclear Regulatory Commission, provides a forum for the discussion of current programs and methods for inservice testing and motor-operated valve testing at nuclear power plants. The symposium also provides an opportunity to discuss the need to improve that testing in order to help ensure the reliable performance of pumps and valves. The participation of industry representatives, regulators, and consultants results in the discussion of a broad spectrum of ideas and perspectives regarding the improvement of inservice testing of pumps and valves at nuclear power plants. Individual papers have been cataloged separately.

Not Available

1994-07-01T23:59:59.000Z

372

PROJECTS FROM FEDERAL REGION IX DOE APPROPRIATE ENERGY TECHNOLOGY PILOT PROGRAM - PART I  

E-Print Network (OSTI)

Results: Energy Savings: F-Chart computer calculations showResults • Energy Savings: F-Chart calculations show primaryto the system. By using F~Chart calculations and assuming an

Case, C.W.

2011-01-01T23:59:59.000Z

373

Simulating the impact of building occupant peer networks on inter-building energy consumption  

Science Conference Proceedings (OSTI)

We developed an integrated inter-building physical and human network model to predict the energy conservation for an assumed urban residential block. We utilized an Artificial Neural Network to predict hourly energy consumption in both the first physical ...

Xiaoqi Xu; Anna Laura Pisello; John E. Taylor

2011-12-01T23:59:59.000Z

374

Control methods and valve arrangement for start-up and shutdown of pressurized combustion and gasification systems integrated with a gas turbine  

DOE Patents (OSTI)

A power plant having a system for converting coal to power in a gas turbine comprises a coal fed pressurized circulating bed for converting coal to pressurized gases, a gas turbine having a compressor for pressurizing air for the pressurized circulating bed and expander for receiving and expanding hot combustion gases for powering a generator, a first fast acting valve for controlling the pressurized air, a second fast acting valve means for controlling pressurized gas from the compressor to the expander.

Provol, Steve J. (Carlsbad, CA); Russell, David B. (San Diego, CA); Isaksson, Matti J. (Karhula, FI)

1994-01-01T23:59:59.000Z

375

Compilation and Evaluation of NOREM (TM) Test Results: Implications for Valve Applications: Generic Background Information for 10 CF R 50.59 Evaluations  

Science Conference Proceedings (OSTI)

EPRI's iron-base NOREM(TM) hardfacing alloy represents a viable generic substitute for cobalt-base Stellite(TM) hardfacing alloys in nuclear valve applications. Based on a wide array of evaluations, this report identifies an acceptable range of conditions for using NOREM in nuclear plant valves to replace cobalt-base hardfacing alloys. The report should prove valuable to utility personnel responsible for performing 10 CFR 50.59 evaluations of NOREM replacements.

1999-06-30T23:59:59.000Z

376

Microstaq | Open Energy Information  

Open Energy Info (EERE)

Microstaq Microstaq Jump to: navigation, search Name Microstaq Place Austin, Texas Zip TX 78744 Product Texas based Microstaq designs flow control valves that enable material energy savings in HVAC, refrigeration, automotive, and other sectors. Coordinates 30.267605°, -97.742984° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":30.267605,"lon":-97.742984,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

377

Energy Basics: Tidal Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Energy Basics Renewable Energy Printable Version Share this resource Biomass Geothermal Hydrogen Hydropower Ocean Ocean Thermal Energy Conversion Tidal Energy Wave Energy...

378

Energy Basics: Wave Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Energy Basics Renewable Energy Printable Version Share this resource Biomass Geothermal Hydrogen Hydropower Ocean Ocean Thermal Energy Conversion Tidal Energy Wave Energy...

379

Energy guides | ENERGY STAR  

NLE Websites -- All DOE Office Websites (Extended Search)

track, and benchmark Improve energy performance ENERGY STAR industrial partnership Energy guides Energy efficiency and air regulation Plant energy auditing Industrial...

380

A Main Steam Safety Valve (MSSV) With Fixed Blowdown According to ASME Section III,Part NC-7512  

Science Conference Proceedings (OSTI)

In 1986, the NRC issued the Information Notice (IN) 86-05 'Main Steam Safety Valve test failures and ring setting adjustments'. Shortly after this IN was issued, the Code was revised to require that a full flow test has to be performed on each CL.2 MSSV by the manufacturer to verify that the valve was adjusted so that it would reach full lift and thus full relieving capacity and would re-close at a pressure as specified in the valve Design Specification. In response to the concern discussed in the IN, the Westinghouse Owners Group (WOG) performed extensive full flow testing on PWR MSSVs and found that each valve required a unique setting of a combination of two rings in order to achieve full lift at accumulation of 3% and re-closing at a blowdown of 5%. The Bopp and Reuther MSSV type SiZ 2507 has a 'fixed blowdown' i.e. without any adjusting rings to adjust the 'blowdown' so that the blowdown is 'fixed'. More than 1000 pieces of this type are successfully in nuclear power plants in operation. Many of them since about 25 years. Therefore it can be considered as a proven design. It is new that an optimization of this MSSV type SiZ 2507 fulfill the requirements of part NC-7512 of the ASME Section III although there are still no adjusting rings in the flow part. In 2000, for the Qinshan Candu unit 1 and 2 full flow tests were performed with 32 MSSV type SiZ 2507 size 8'' x 12'' at 51 bar saturated steam in only 6 days. In all tests the functional performance was very stable. It was demonstrated by recording the signals lift and system pressure that all valves had acceptable results to achieve full lift at accumulation of 3% and to re-close at blowdown of 5%. This is an advantage which gives a reduction in cost for flow tests and which gives more reliability after maintenance work during outage compared to the common MSSV design with an individual required setting of the combination of the two rings. The design of the type SiZ 2507 without any adjusting rings in the flow path is presented. The stable performance depends on the interaction of flow force and spring force. The optimization of the flow path to create a suitable flow-force-curve was managed by Computational Fluid Dynamics (CFD) and flow-force-characteristic-measurements at a model 1: 2.5. The method of the flow-force-characteristic-measurement permits systematic dimensioning of valve spring forces by means of measurement of the fluid mechanical forces occurring on the valve spindle during flow. A special procedure was established to verify a spring force versus lift curve with an accuracy of 1% for each production valve. This gives high reliability at required stable performance and this can not be influenced by wrong setting of any adjusting ring during maintenance work. (authors)

Follmer, Bernhard; Schnettler, Armin [Bopp and Reuther Sicherheitsund Regelarmaturen, GmbH, Mannheim (Germany)

2002-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Aging and service wear of air-operated valves used in safety-related systems at nuclear power plants  

SciTech Connect

Air-operated valves (AOVs) are used in a variety of safety-related applications at nuclear power plants. They are often used where rapid stroke times are required or precise control of the valve obturator is required. They can be designed to operate automatically upon loss of power, which is often desirable when selecting components for response to design basis conditions. The purpose of this report is to examine the reported failures of AOVs and determine whether there are identifiable trends in the failures related to predictable causes. This report examines the specific components that comprise a typical AOV, how those components fail, when they fail, and how such failures are discovered. It also examines whether current testing frequencies and methods are effective in predicting such failures.

Cox, D.F.; McElhaney, K.L.; Staunton, R.H.

1995-05-01T23:59:59.000Z

382

System to inject steam and produce oil from the same wellbore through downhole valve switching. Final report  

SciTech Connect

Through direct contacts with many California Operators, the potential market for this technology and hardware was more closely defined. The largest market might be for re-entry into existing but shut-in wells, equipped with 7{double_prime}OD cemented casings, for which a suitable configuration was designed. For field-testing any prototype Downhole equipment, however, Operators and Service Companies prefer to start with a new well, for better control of the well characteristics. In the relatively shallow reservoirs where Steam injection is currently used with success, the additional drilling cost, in soft formations, is sufficiently small that this became the main design case. Substantial savings were obtained by reducing the number of Downhole valves from two to one and by replacing the twin hydraulically-controlled ball or flapper-type valves with a single sliding sleeve valve, operated by wireline. Laboratory tests conducted at UC-Berkeley confirmed the satisfactory operation of this type of valve with wet steam over extended periods. Low reservoir pressures dictated the use of artificial lift methods, with rod pumps considered the most economical. The availability of live steam downhole at all times is, however, a major advantage which led to the selection of a combined method of artificial lift: (1) steam-lift of the produced fluids up to the kick-off point of the medium curvature drainholes, (2) dumping of the produced fluids into a vertical separator/sump below the kick-off points, (3) vertical rod pumping of the liquid phases from the downhole separator/sump to the surface through a dedicated production tubing.

Not Available

1994-10-01T23:59:59.000Z

383

The Secretary of Energy  

Office of Legacy Management (LM)

The Secretary of Energy The Secretary of Energy Washington. bC-20585 -.. October 10, 1997 . - The Honorable Wlliam S. Cohen ' Secretary ofDefense Washington, D.C. 2030' 1 Dear Mr. Secremy: ' The Congress recently sent to the President for signature the Energy and Water Development Appropriations A&' 1998. Among other provisions, this bill would immediately transfer responsibility for the Formerly ' Utilized Sites Remedial Action Program (FUSMP) from the Department of Energy to the United States Army Corps of Engineers. Assuming that this transfer becomes law, but without prejudging the President' s decision, the Department of Energy will work with the Corps to ensure. a prompt and smooth transition, consistent with the wishes of the Congress. Should this provision become law, the Department of Energy'

384

Data:53fcf411-97d9-4d51-b9ba-09f48c7f43d6 | Open Energy Information  

Open Energy Info (EERE)

Rate name: A F Sector: Industrial Description: Source or reference: http:www.highwest-energy.compublicindex.phpcustservicescontent-all-comcontent-viewsrates Assume net...

385

Integration of distributed energy resources. The CERTS Microgrid Concept  

E-Print Network (OSTI)

Energy Resources The CERTS MicroGrid Concept Prepared forTechnology Solutions (CERTS) MicroGrid concept assumes anflexibility allows the CERTS MicroGrid to present itself to

2002-01-01T23:59:59.000Z

386

Expanding Robust HCCI Operation with Advanced Valve and Fuel Control Technologies Pub ID 38707 Title Expanding Robust HCCI Operation with Advanced Valve and Fuel Control Technologies Status Distributed Communication Type ORNL report ORNL Review? Scientific communication that requires ORNL review Information Category Protected CRADA Information ORNL Report Classification Final Expanding Robust HCCI Operation with Advanced Valve and Fuel Control Technologies  

SciTech Connect

Delphi Automotive Systems and ORNL established this CRADA to advance the commercialization potential of the homogeneous charge compression ignition (HCCI) advanced combustion strategy for gasoline engine platforms. HCCI combustion has been shown by others to produce high diesel-like efficiency on a gasoline engine platform while simultaneously producing low NOX and particulate matter emissions. However, the commercialization barriers that face HCCI combustion are significant, with requirements for a more active engine control system, likely with next-cycle closed-loop feedback control, and with advanced valve train technologies to enable negative valve overlap conditions. In the partnership between Delphi and ORNL, each organization brought a unique and complementary set of skills to the project. Delphi has made a number of breakthroughs with production-intent valve train technologies and controls in recent years to make a part time production-intent HCCI engine plausible. ORNL has extensive knowledge and expertise with HCCI combustion, and also has a versatile research engine with hydraulic valve actuation (HVA) that is useful for guiding production of a cam-based HCCI system. Partnering these knowledge bases and capabilities was essential towards making progress to better understand HCCI combustion and the commercialization barriers that it faces. ORNL and Delphi maintained strong collaboration throughout the project. Meetings were held regularly, with additional reports, presentations, and meetings as necessary to maintain progress. Delphi provided guidance to ORNL regarding operational strategies to investigate on their single-cylinder research engine with HVA and data from their experimental multi-cylinder engine for modeling. ORNL provided single-cylinder engine data and modeling results.

Szybist, J.P.; Confer, K. (Delphi Automotive Systems)

2012-09-11T23:59:59.000Z

387

Singularity-free dark energy star  

E-Print Network (OSTI)

We propose a model for an anisotropic dark energy star where we assume that the radial pressure exerted on the system due to the presence of dark energy is proportional to the isotropic perfect fluid matter density. We discuss various physical features of our model and show that the model satisfies all the regularity conditions and stable as well as singularity-free.

Farook Rahaman; Anil Kumar Yadav; Saibal Ray; Raju Maulick; Ranjan Sharma

2011-02-07T23:59:59.000Z

388

Energy cooperation in energy harvesting wireless communications  

E-Print Network (OSTI)

Abstract—We consider a simple multi-hop communication scenario composed of a source node, a relay node and a destination node where the source and the relay can harvest energy from the nature. Energy required for communication arrives (is harvested) at the transmitter and an unlimited battery stores it before being consumed for transmission. In addition, the source can assist the relay by transferring a portion of its energy to the relay through a separate energy transfer unit. We address this energy cooperation between the source and the relay in a deterministic setting. Assuming that the source and the relay nodes are informed of the energy arrivals in advance, we find jointly optimal offline energy management policies for the source and the relay that maximize the end-to-end throughput. We show that this problem is a convex problem. In order to gain insight about the structure of the solution, we consider specific scenarios. In particular, we show that if the relay energy profile is higher at the beginning and lower at the end with only one intersection, then matching the power sequences of the source and the relay slot-by-slot is optimal. We also consider the case when the energy of the source is available at the beginning and show that transferring energy in the first slot is optimal. I.

Berk Gurakan; Omur Ozel; Jing Yang; Sennur Ulukus

2012-01-01T23:59:59.000Z

389

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

81 - 4790 of 26,777 results. 81 - 4790 of 26,777 results. Download CX-001134: Categorical Exclusion Determination Repair Water Leak in L-Area Valve 075 CX(s) Applied: B1.3 Date: 03/04/2010 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office http://energy.gov/nepa/downloads/cx-001134-categorical-exclusion-determination Download CX-001018: Categorical Exclusion Determination Internal Short Circuits in Lithium-Ion Cells for Plug-In Electric Vehicle (PHEV) CX(s) Applied: B3.6 Date: 03/04/2010 Location(s): Cambridge, Massachusetts Office(s): Energy Efficiency and Renewable Energy, National Energy Technology Laboratory http://energy.gov/nepa/downloads/cx-001018-categorical-exclusion-determination Download CX-005147: Categorical Exclusion Determination

390

Biquadratic coupling effect on magnetoresistance response curves of spin valves with a synthetic antiferromagnet  

SciTech Connect

Both normal and inverse magnetoresistance (MR) response curves were observed for synthetic spin valves with the structure of Si(100)/Ru/Co(t{sub 1})/Ru(0.7nm)/Co(t{sub 2})/Cu(3nm)/Co(t{sub 3})/Ru. Under the assumption of a coherent rotation of the magnetization in the three Co layers, the hysteresis loops, magnetization response, and MR response curves were calculated as a function of the parameters of the system. The parameters include antiferromagnetic coupling of Co(t{sub 1}) and Co(t{sub 2}) through Ru layer, a weak ferromagnetic coupling of Co(t{sub 2}) and Co(t{sub 3}) through Cu spacer, giant magnetoresistance of the Co/Cu/Co and Co/Ru/Co systems, and AMR contribution of each Co layer. The uniaxial anisotropy of each Co layer and a distribution of the coupling strength of Co(t{sub 1})/Ru/Co(t{sub 2}) were also included. To fit the experimental data well, it was necessary to include a biquadratic coupling in the Co(t{sub 1})/Ru/Co(t{sub 2}) trilayer. {copyright} 2001 American Institute of Physics.

Zhang, K.; Kai, T.; Zhao, T.; Fujiwara, H.; Mankey, G. J.

2001-06-01T23:59:59.000Z

391

Home Energy Score Calculation Methodology | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Home Energy Score Calculation Methodology Home Energy Score Calculation Methodology Home Energy Score Calculation Methodology A Qualified Assessor calculates the Home Energy Score by first conducting a brief walk-through of the home and collecting approximately 40 data points. Next, the Qualified Assessor uses the Home Energy Scoring Tool to estimate the home's energy use. The Scoring Tool converts it into a Score and develops recommendations for energy improvements. All the data required to calculate the Home Energy Score is listed in the Data Collection Sheet. The calculation method holds a number of variables constant. For example, it assumes, that the thermostat is set at specific levels at various points of the year, and that homeowners use appliances in a standard way. By holding these other variables constant, the Home Energy Score allows

392

Missouri | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

from a Protective Inspection, a copy of the paid receipt with model numbers for the condenser, matched evaporator coil, expansion valve and any additional installed equipment....

393

A Hybrid Energy System Using Cascaded H-bridge Converter , Zhong Du2  

E-Print Network (OSTI)

energy system, cascaded multilevel converter, single dc source I. INTRODUCTION As different energy generation, storage, and transmission. The power from hybrid energy systems can be combined on the dc side of Energy Source 1 and Energy Source 2. To analyze mode I, a dc source is assumed to be connected

Tolbert, Leon M.

394

Progress In Electromagnetics Research B, Vol. 12, 259295, 2009 AN ESTIMATION OF SENSOR ENERGY CONSUMP-  

E-Print Network (OSTI)

that minimizes energy dissipation. As in [25], we assume a symmetric radio channel making the energy needed). where Vsup is the supply voltage. 2.2. Sensor Logging Sensor logging consumes energy used for reading b-controller, is attributed to two components: energy loss from switching, Eswitch, and energy loss due to leakage current

Halgamuge, Malka N.

395

The Secretary of Energy  

Office of Legacy Management (LM)

The Secretary of Energy The Secretary of Energy 0, .: ., Washington, bC-20585 . . October 10, 19g7 ' , .-. , The Honorable W illiam S. Cohen Secretary ofDefense Washington, D.C. 203Oi .. . . &arMi.Se&etaQ: ~ , . ' . The Congress recently sent to the President for signature the Energy and Water . Development Appropriations Act,' 1998. Among other provisions, this bill would immediately transfer responsibility for' the Formerly~Utilized Sites Remedial Action Program (FUSRAP) from the Department of Energy to the United States Army Corps of Engineers. Assuming that this transfer becomes law, but without prejudging the President' s decision, the Department of Energy will work with the Corps to ensure a prompt and smooth transition, consistent with the wishes of the

396

Health Satisfaction and Energy Spending  

E-Print Network (OSTI)

on the direct link between energy spending and health satisfaction and control for impacts of other determinants such as access to gas, age, income, and satisfaction levels in other domains of life such as social life or leisure. Indirect effects are assumed... in the context with energy affordability. Rising energy prices and the realization of climate change objectives will have impacts on energy usage and spending of households. At least for some households it will for example be more difficult to warm their homes...

Meier, Helena

397

Energy outlook for the eighties  

SciTech Connect

Energy Information Administration (EIA) forecasts assume a 3.1% annual economic growth between 1985 and 1990 and a 2.3% rate between 1990 and 1995. Current projections are for lower prices and higher consumption for petroleum and little change in natural gas markets. Total energy consumption is expected to grow by 2% between 1985 and 1990, with energy consumption per dollar of gross national product declining at about 1% per year. These projections are lower than those made previously because of the drop in world oil prices, the renewed strength in energy-intensive industries, and a strong trend toward electrification.

Montgomery, D.W.

1985-08-01T23:59:59.000Z

398

Energy Resource Potential  

NLE Websites -- All DOE Office Websites (Extended Search)

Resource Potential Resource Potential of Methane Hydrate Energy Resource Potential An introduction to the science and energy potential of a unique resource Disclaimer Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States Government or any agency thereof. Neither the United States Government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights.

399

Financial Impact of Energy Efficiency under a Federal Renewable Electricity Standard: Case Study of a Kansas "super-utility"  

E-Print Network (OSTI)

first-year 2012 cost for wind energy under a power purchaseCost Study of the 2015 Wind Challenge: An Assessment of Wind Energycosts, we assumed that the super-utility had a preference for wind energy.

Cappers, Peter

2010-01-01T23:59:59.000Z

400

Energy savings potential from energy-conserving irrigation systems  

SciTech Connect

This report systematically compares, within a consistent framework, the technical and economic characteristics of energy-conserving irrigation systems with those of conventional irrigation systems and to determine total energy savings. Levelized annual costs of owning and operating both energy-conserving and conventional irrigation systems have been developed and compared for all 17 states to account for the differences in energy costs and irrigation conditions in each state. Market penetration of energy-conserving systems is assessed for those systems having lower levelized annual costs than conventional systems performing the same function. Annual energy savings were computed by matching the energy savings per system with an assumed maximum market penetration of 100 percent in those markets where the levelized annual costs of energy-conserving systems are lower than the levelized annual costs of conventional systems.

Wilfert, G.L.; Patton, W.P.; Harrer, B.J.; Clark, M.A.

1982-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Potential for Renewable Energy Development: Alternatives to AEO2001  

E-Print Network (OSTI)

Preface The U.S. Department of Energy's Energy Information Administration (EIA) has developed for analysis of policy initiatives. The reference case projections of the AEO assume continuing market changesLBNL-51499 Potential for Renewable Energy Development: Alternatives to AEO2001 Julie Osborn

402

Quantum-Gravity phenomenology and high energy particle propagation  

E-Print Network (OSTI)

Quantum-gravity effects may introduce relevant consequences for the propagation and interaction of high energy cosmic rays particles. Assuming the space-time foamy structure results in an intrinsic uncertainty of energy and momentum of particles, we show how low energy (under GZK) observations can provide strong constraints on the role of the fluctuating space-time structure.

R. Aloisio; P. Blasi; A. Galante; P. L. Ghia; A. F. Grillo

2004-10-18T23:59:59.000Z

403

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

51 - 15260 of 31,917 results. 51 - 15260 of 31,917 results. Download Engineered Solutions: Proposed Penalty (2010-CE-2112) DOE alleged in a Notice of Proposed Civil Penalty that Engineered Solutions, Inc. failed to certify a dehumidifier as compliant with the applicable energy conservation standards. http://energy.gov/gc/downloads/engineered-solutions-proposed-penalty-2010-ce-2112 Download Sanyo Electric: Proposed Penalty (2010-CE-1210) DOE alleged in a Notice of Proposed Civil Penalty that Sanyo Electric Co. failed to certify a variety of refrigerators, refrigerator-freezers, and freezers as compliant with the applicable energy conservation standards. http://energy.gov/gc/downloads/sanyo-electric-proposed-penalty-2010-ce-1210 Download American Valve: Proposed Penalty (2010-CW-1411)

404

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

41 - 9850 of 28,560 results. 41 - 9850 of 28,560 results. Download CX-006939: Categorical Exclusion Determination Flushing of the Ellenton Header & R-Normal River Water Lines CX(s) Applied: B1.3 Date: 10/10/2011 Location(s): Aiken, South Carolina Office(s): Environmental Management, National Energy Technology Laboratory http://energy.gov/nepa/downloads/cx-006939-categorical-exclusion-determination Download CX-006944: Categorical Exclusion Determination Remove Insulation from High Point Flush Pump Drain Valve CX(s) Applied: B1.3 Date: 10/03/2011 Location(s): Aiken, South Carolina Office(s): Environmental Management, National Energy Technology Laboratory http://energy.gov/nepa/downloads/cx-006944-categorical-exclusion-determination Download CX-006951: Categorical Exclusion Determination

405

Energy Savings of Variable Speed Motors  

E-Print Network (OSTI)

This paper investigates the energy savings available by utilizing variable speed motors on pump and fan applications. Conventional control of flow or pressure in process plants is normally accomplished by throttling the various streams with control valves. Depending on the system and the actual operating conditions, this throttling may consume a considerable amount of energy. The hydraulics of different systems are investigated to generalize high energy saving applications. Typical pump characteristics at varying speeds are investigated since most performance curves are only available at a constant speed. The various types of variable speed electric motors are discussed. However, the primary variable speed system recommended is a variable frequency speed system which utilizes standard induction motors. Specific cases of centrifugal pump applications and cooling tower fan service are presented. Turndown frequencies, stream factors, and electric rates are included in the evaluation. The energy savings of a variable speed system becomes significant when flow rates vary widely and the electrical rates are high.

Fishel, F. D.

1979-01-01T23:59:59.000Z

406

MHK Technologies/European Pico Pilot Plant | Open Energy Information  

Open Energy Info (EERE)

European Pico Pilot Plant European Pico Pilot Plant < MHK Technologies Jump to: navigation, search << Return to the MHK database homepage European Pico Pilot Plant.jpg Technology Profile Primary Organization Wave Energy Centre Project(s) where this technology is utilized *MHK Projects/OWC Pico Power Plant Technology Resource Click here Wave Technology Type Click here Oscillating Water Column Technology Readiness Level Click here TRL 4: Proof of Concept Technology Description A bottom mounted shoreline oscillating water column structure equipped with a horizontal axis Wells turbine generator set and a guide vane stator installed on each side of the rotor Control options are facilitated by a relief valve presently a slow acting valve with plans to substitute a fast acting mechanism in the wave chamber

407

Data:Ea7d8a10-6d64-4a12-96ba-f6e00f42f71a | Open Energy Information  

Open Energy Info (EERE)

Power T-O-D Sector: Industrial Description: Source or reference: http:www.highwest-energy.compublicindex.phpcustservicescontent-all-comcontent-viewsrates Assume net...

408

Procuring Architectural and Engineering Services for Energy Efficiency and Sustainability (Book), Federal Energy Management Program (FEMP)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Procuring Architectural Procuring Architectural and Engineering Services for Energy Efficiency and Sustainability A Resource Guide for Federal Construction Project Managers U.S. Department of Energy Energy Efficiency and Renewable Energy Federal Energy Management Program FEDERAL ENERGY MANAGEMENT PROGRAM Procuring Architectural and Engineering Services for Energy Efficiency and Sustainability: A Resource Guide for Federal Construction Project Managers NOTICE This report was prepared as an account of work sponsored by an agency of the United States government. Neither the United States government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, appa-

409

Year 2000: energy enough  

SciTech Connect

The growing needs for energy in the U.S. are reviewed, and it is predicted that energy supplies will need be more than doubled by the year 2000. The solution lies in three areas: goal targeting, resource management, and timing. A no-growth economy and an economy continuing growth at an appropriate rate are two scenarios discussed. The second major area of choice in fixing energy capabilities for the year 2000 involves management of fuel resources. Shortages of oil and gas dictate that the increase in energy consumption be changed to coal and uranium, both of which are available domestically; utilization of these energy sources will mean increased electrification. It is concluded, then, that the best avenues toward ensuring a national energy supply are utilization of coal and uranium and the practice of energy conservation through greater efficiency. Timing is the third critical area of decision making that affects future energy supply. The long lead time required to bring about a change in the national energy mix is cited. Current estimates indicate that now is the time to push toward a national electricity target of at least 7500 billion kWh for the year 2000. Meeting the target means almost four times the present electricity supply, at a growth rate of about 5.7 percent per year. This target assumes a reasonable measure of energy conservation. (MCW)

Starr, C.

1976-06-01T23:59:59.000Z

410

The Secretary of Energy  

Office of Legacy Management (LM)

The Secretary of Energy 0 ' -. . . _ Washington, bC 20585 . October 10, 1997 ' , :-. The FIonorable% William S. Cohen : Secretary ofijefense Washington, D.C. 203Oi -' 8 1 .' *- . A .' JharMiSecietary: , ' The Congress recently sent to the Fresident for signature the Energy and Water ' Development Appropriations Act, 1998. Among other provisions, this bill would immediately transfer responsibility for the Formerly Utilized Sites Remedial Action Program (FUSRAP) from the Department -of Energy to the United States Army Corps of Engineers.. Assuming that this transfer becomes law, but without prejudging the President' s decision, the Department of Energy will work with the Corps to ensure a prompt and smooth transition, consistent with the wishes of the

411

The Secretary of Energy'  

Office of Legacy Management (LM)

:c> 2" ' :c> 2" ' $,,. I ,- ; ' . The Secretary of Energy' 0 "-. Washington. bC 20585 ._. . . October 10, 1997 ' \ . : ' . Y' . -. - The Honorable Wdliam S. Cohen " Smetary ofDefense Washington, D.C. 20301 .' .&r Mr. Secretary: f : ,~The' Congress recently sent to,the ,President' for signature the Energy and Water Development Appropriations Act, 1998., ;Among other provisions, ,this bi would immediately transfer responsibility for the Formerly~Utilized Sites Remedial Action Program @' USRAP) from the Department .of Energy to the United States Army Corps of Engineers. -~Assuming that this transfer becomes law, but without prejudging the President' s decision, the Department of Energy will work with the Corps to ensure a prompt and smooth transition, consistent with the wishes ofthe

412

The Secretary of Energy  

Office of Legacy Management (LM)

' ' The Secretary of Energy cj L. _ Washington. bC 20585 1 .) :-. . . The .Honora.l$eZ William S. Cohen . Secretary ofDefense Washington, D.C. 203Oi .' .&a.rMr.Secietary: ' , ' - a- - * . ' The Congress recently sent to the President for signature the Energy and Water Development Appropriations Act, 1998. Among other provisions, this bill would immediately transfer responsibility for the Forrnerly' Utilized Sites Remedial Action Program (FUSRAP) from the Department of Energy to the United States Army Corps of Engineers.. Assuming that this transfer becomes law, but without prejudging the President' s decision, the Department of Energy will work with the Corps to ensure a prompt and smooth transition, consistent with the wishes of the Congress.

413

The Secretary of Energy'  

Office of Legacy Management (LM)

? >g*+. , . ? >g*+. , . dc*rb&.+ :c-r.3-b. g ;.i' 8 . I. ' . . 3 @ g. -- Q ' \ 4,: 6 L;Is)zLTEsdi# ' -. . ! h -. The Secretary of Energy' Washington, bC 20585 u , October 10, 1997 ' The .Honorabie William S . Cohen Secretary ofDefense Washington, D.C. 20301 -' &arMr. Secietary: !I " .,.. *- . = . . # ' The Congress recently se@ to the President for signature the Energy and Water ,, Development Appropriations Act, 1998. Among other provisions, this bill would immediately transfer responsibility for the Formerly Utilized Sites Remedial Action Program (FUSRAP) from the Department of Energy to the United States Army Corps of Engineers.. Assuming that this transfer becomes law, but without prejudging the President' s decision, the Department of Energy will work with the

414

Robotics and Energy Usage  

E-Print Network (OSTI)

It is commonly assumed that the use of robots in an industrial plant will cut energy usage, because robots require no heat, light, or air conditioning in their work space. However, in analyzing industrial installations, we have found that, in practice, energy usage may either increase or decrease depending on the parameters of the particular facility. This paper describes our findings at the plants of various manufacturers. We performed on-site studies at plants operated by Chrysler Corporation in St. Louis (62 welding robots) and Franklin Manufacturing Company in St. Cloud, Minnesota (4 spray painting robots used in freezer manufacture), We also examined data on energy effects of robots from John Deere, caterpillar, and GM Guide Division. The effect of robots on electricity usage and other forms of energy usage are analyzed in this paper.

Hershey, R. L.; Fenton, S. E.; Letzt, A. M.

1983-01-01T23:59:59.000Z

415

This report was prepared as an account of work sponsored by an agency of the United States government. Neither the United States government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal li  

E-Print Network (OSTI)

. SNS and HFIR are funded by the U.S. Department of Energy Office of Basic Energy Sciences. 2008 ANNUAL Flux Isotope Reactor (HFIR), bringing users to our facilities, and producing scientific results. I must to achieve 1.4 megawatts of beam power by FY 2010 or CY 2011. At HFIR, the new cold source operated

416

U.S. Energy Information Administration (EIA) - Sector  

Gasoline and Diesel Fuel Update (EIA)

Focus Focus Introduction The "Issues in focus" section of the Annual Energy Outlook (AEO) provides an in-depth discussion on topics of special interest, including significant changes in assumptions and recent developments in technologies for energy production and consumption. Detailed quantitative results are available in Appendix D. The first topic updates a discussion included in the Annual Energy Outlook 2011 (AEO2011) that compared the results of two cases with different assumptions about the future course of existing energy policies. One case assumes the elimination of sunset provisions in existing energy policies; that is, the policies are assumed not to sunset as they would under current law. The other case assumes the extension or expansion of a

417

Study of sustainability of renewable energy sources through GIS analysis techniques  

Science Conference Proceedings (OSTI)

In an integrated vision of the problems concerning energy policies, the use of renewable energy sources should assume a significant role. The 2009/28/EC Directive of the European Parliament and Council has indicated ambitious energy and climate change ... Keywords: GIS, renewable energy sources, solar radiation, sustainable development

Emanuela Caiaffa; Alessandro Marucci; Maurizio Pollino

2012-06-01T23:59:59.000Z

418

On the Relationship between Discrete and Continuous Energy Spectra of SU(N) Supermembrane Matrix Model  

E-Print Network (OSTI)

It has been known that SU(N) supermembrane matrix model has continuous energy spectrum, and it has also been conjectured that it has a normalizable energy eigenstate. Assuming that there exists a normalizable energy eigenstate for each N, we show that there exists a branch of continuous energy spectrum for each partition of N.

Yoji Michishita

2013-08-13T23:59:59.000Z

419

On the Relationship between Discrete and Continuous Energy Spectra of SU(N) Supermembrane Matrix Model  

E-Print Network (OSTI)

It has been known that SU(N) supermembrane matrix model has continuous energy spectrum, and it has also been conjectured that it has a normalizable energy eigenstate. Assuming that there exists a normalizable energy eigenstate for each N, we show that there exists a branch of continuous energy spectrum for each partition of N.

Michishita, Yoji

2013-01-01T23:59:59.000Z

420

1ST IEEE INTERNATIONAL CONFERENCE ON SMART GRID COMMUNICATIONS, 2010 1 Efficient Algorithms for Renewable Energy  

E-Print Network (OSTI)

for Renewable Energy Allocation to Delay Tolerant Consumers Michael J. Neely, Arash Saber Tehrani, Alexandros G. Dimakis Abstract-- We investigate the problem of allocating energy from renewable sources to flexible consumers in electricity markets. We assume there is a renewable energy supplier that provides energy

Neely, Michael J.

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

CX-000040: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0: Categorical Exclusion Determination 0: Categorical Exclusion Determination CX-000040: Categorical Exclusion Determination Pima-Maricopa Indian Community of the Salt River Reservation Energy Efficiency Retrofits CX(s) Applied: B5.1, B2.5 Date: 11/06/2009 Location(s): Arizona Office(s): Energy Efficiency and Renewable Energy The proposed energy efficiency retrofits include three individual activities to be funded under the Energy Efficiency and Conservation Block Grant program: 1) Installation of motion sensors at the Two Waters Complex on the lighting systems in mechanical rooms, electrical rooms, conference rooms and storage rooms. 2) Adding 2 Variable Speed Drives (VSDs) (and controls) to the main pumps and adding 45 solenoid valves on the feed pumps at the central activity plant. 3) Replace old appliances for energy

422

CX-001274: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

274: Categorical Exclusion Determination 274: Categorical Exclusion Determination CX-001274: Categorical Exclusion Determination Energy Efficiency Retrofits CX(s) Applied: B2.5, B5.1 Date: 12/10/2009 Location(s): Belknap, New Hampshire Office(s): Energy Efficiency and Renewable Energy Energy Efficiency and Conservation Block Grant for: Energy efficiency retrofits in County facilities, including building envelope improvements, thermostatically controlled radiator valves with set-back capability, connect Old Wing Heating System to New Wing Heating System in the County Jail, and Water and Energy Conservation Measures throughout all County facilities (including Courthouse, built in 1893). DOCUMENT(S) AVAILABLE FOR DOWNLOAD CX-001274.pdf More Documents & Publications CX-005795: Categorical Exclusion Determination

423

CX-001814: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

14: Categorical Exclusion Determination 14: Categorical Exclusion Determination CX-001814: Categorical Exclusion Determination Energy Efficiency and Renewable Energy Retrofits for Oxford County Buildings CX(s) Applied: B2.2, B5.1 Date: 04/22/2010 Location(s): Oxford County, Maine Office(s): Energy Efficiency and Renewable Energy Energy Efficiency and Conservation Block Grant funding will be used to replace outdated or poorly functioning equipment located in three County-owned buildings. The installation of a pellet boiler, conversion of the Courthouse from steam to hydronic, adding zone valves, upgrading to efficient fluorescent lighting, installation of energy efficient replacement window are retrofit activities selected from lighting and Heating Ventilation and Air Conditioning audit reports.

424

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

41 - 12850 of 28,905 results. 41 - 12850 of 28,905 results. Download Small Modular Reactors and U.S. Clean Energy Sources for Electricity For the clean energy goal to be met, then, the non-carbon emitting sources must provide some 2900 TWhr. Hydropower is generally assumed to have reached a maximum of 250 TWhr, so if we assume... http://energy.gov/ne/downloads/small-modular-reactors-and-us-clean-energy-sources-electricity Download MAS 10.1 Implementation of the Integrated Safety Management System (ISMS) Process in Maintenance Activities, 2/14/2000 The objective of this surveillance is to evaluate the effectiveness of the contractor's ISMS process with regard to maintenance activities. Surveillance activities encompass work planning and... http://energy.gov/hss/downloads/mas-101-implementation-integrated-safety-management-system-isms

425

Categorical Exclusion Determinations: Texas | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

April 30, 2013 April 30, 2013 CX-010299: Categorical Exclusion Determination A 1,000 Level Drill Pipe Deployed Fiber Optic 3C Receiver Array for Deep Boreholes CX(s) Applied: A9, B3.6 Date: 04/30/2013 Location(s): Texas Offices(s): National Energy Technology Laboratory April 29, 2013 CX-010170: Categorical Exclusion Determination ChargePoint America CX(s) Applied: A9, A11, B5.1, B5.23 Date: 04/29/2013 Location(s): Texas Offices(s): National Energy Technology Laboratory April 17, 2013 CX-010188: Categorical Exclusion Determination Field Demonstration of a Novel Eco-Friendly Production Enhancement Process CX(s) Applied: B3.11 Date: 04/17/2013 Location(s): Texas Offices(s): National Energy Technology Laboratory April 16, 2013 CX-010402: Categorical Exclusion Determination Purchase of Big Hill Control Valve Assembly

426

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

11 - 9320 of 28,560 results. 11 - 9320 of 28,560 results. Download CX-006247: Categorical Exclusion Determination Relocation of Bayou Choctaw Helipad CX(s) Applied: B1.3 Date: 06/13/2011 Location(s): Iberville Parish, Louisiana Office(s): Strategic Petroleum Reserve Field Office http://energy.gov/nepa/downloads/cx-006247-categorical-exclusion-determination Download CX-000873: Categorical Exclusion Determination Clean, Inspect, and Repair BMT-27 CX(s) Applied: B1.3 Date: 02/11/2010 Location(s): Texas Office(s): Fossil Energy, Strategic Petroleum Reserve Field Office http://energy.gov/nepa/downloads/cx-000873-categorical-exclusion-determination Download CX-000871: Categorical Exclusion Determination West Hackberry Annual Pressure Safety Valve Testing CX(s) Applied: B1.3 Date: 02/05/2010 Location(s): West Hackberry, Louisiana

427

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

11 - 14220 of 29,416 results. 11 - 14220 of 29,416 results. Download CX-010016: Categorical Exclusion Determination Energy Frontiers Research Center - Nanoscale Actinide Materials CX(s) Applied: B3.6 Date: 01/29/2013 Location(s): South Carolina Offices(s): Savannah River Operations Office http://energy.gov/nepa/downloads/cx-010016-categorical-exclusion-determination Download CX-010017: Categorical Exclusion Determination L-Area River Water Valve V-022 Bypass and Piping CX(s) Applied: B1.3 Date: 01/29/2013 Location(s): South Carolina Offices(s): Savannah River Operations Office http://energy.gov/nepa/downloads/cx-010017-categorical-exclusion-determination Download CX-010018: Categorical Exclusion Determination 2H Evaporator Scale Sample Analysis CX(s) Applied: B3.6 Date: 01/28/2013 Location(s): South Carolina

428

Energy Efficiency and Conservation Block Grant Program  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

TN-County-Hamilton TN-County-Hamilton Location: County Hamilton TN American Recovery and Reinvestment Act: Proposed Action or Project Description 1) Install green roof on Health Department East Third Street HQ Facility, 2) create Go Green Education Program and technical consultant services to develop program, 3) lighting replacement project to replace incandescent lighting with more energy efficient technology, 4) building energy audits/assessment by technical consultant and purchase assessment software, 5) conduct energy efficiency upgrades to the McDaniel Building (lighting replacements, light-emitting diode lights in exit signs, automatic flush valves, and faucet and occupancy sensors), and 6) replace lighting at Chester Foster Park Pavilion and upgrade electrical system.

429

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

31 - 21240 of 28,560 results. 31 - 21240 of 28,560 results. Download Independent Activity Report, Sandia National Laboratories- March 2013 Operational Awareness Oversight of Sandia National Laboratories [HIAR SNL-2013-03-18] http://energy.gov/hss/downloads/independent-activity-report-sandia-national-laboratories-march-2013 Download CX-010402: Categorical Exclusion Determination Purchase of Big Hill Control Valve Assembly CX(s) Applied: B1.3 Date: 04/16/2013 Location(s): Texas Offices(s): Strategic Petroleum Reserve Field Office http://energy.gov/nepa/downloads/cx-010402-categorical-exclusion-determination Page ALOHA Code Central Registry Toolbox Code Version(s): V5.2.3 http://energy.gov/hss/aloha-code Download NTSF Activities and Accomplishments Presentation made by Christopher Wells for the NTSF annual meeting held

430

Energy Information Administration (EIA) - Energy and Economic ...  

U.S. Energy Information Administration (EIA)

In 2030, projected revenue for the EPA allowances is $103.6 billion, and that for the additional safety valve allowances is $17.8 billion, totaling $121.4 billion.

431

EIA - Forecasts and Analysis of Energy Data  

Gasoline and Diesel Fuel Update (EIA)

G: Key Assumptions for the IEO2005 Kyoto Protocol Case G: Key Assumptions for the IEO2005 Kyoto Protocol Case Energy-Related Emissions of Greenhouse Gases The System for the Analysis of Global energy Markets (SAGE)—the model used by the Energy Information Administration (EIA) to prepare the International Energy Outlook 2005 (IEO2005) mid-term projections—does not include non-energy-related emissions of greenhouse gases, which are estimated at about 15 to 20 percent of total greenhouse gas emissions, based on inventories submitted to the United Nations Framework Convention on Climate Change (UNFCCC). SAGE models global energy supply and demand and, therefore, does not address agricultural and other non-energy-related emissions. EIA implicitly assumes that percentage reductions of non-energy-related emissions and their associated abatement costs will be similar to those for energy-related emissions. Non-energy-related greenhouse gas emissions are likely to grow faster than energy-related emissions; however, the marginal abatement costs for non-energy-related greenhouse gas emissions are not known and cannot be estimated reliably. In SAGE, each region’s emissions reduction goal under the Kyoto Protocol is based only on the corresponding estimate of that region’s energy-related carbon dioxide emissions, as determined by EIA data. It is assumed that the required reductions will also be proportionately less than if all gases were included.

432

Reconstructing Quintom from Ricci Dark Energy  

E-Print Network (OSTI)

The holographic dark energy with Ricci scalar as IR cutoff called Ricci dark energy(RDE) probes the nature of dark energy with respect to the holographic principle of quantum gravity theory. The scalar field dark energy models like quintom are often viewed as effective description of the underlying field theory of dark energy. In this letter, we assume RDE model as the underlying field theory to find how the generalized ghost condensate model(GGC) that can easily realize quintom behavior can be used to effectively describe it and reconstruct the function $h(\\phi)$ of the generalized ghost condensate model.

Chao-Jun Feng

2008-10-15T23:59:59.000Z

433

Job Cards for Pump and Valve Maintenance: Volume 2: Feasibility of Industrywide Implementation Joint EPRI-CRIEPI Human Factors Studi es  

Science Conference Proceedings (OSTI)

Volume 2 of this report describes the results of a utility survey to determine the feasibility of implementing, on an industrywide basis, a set of ruggedized job cards to aid personnel in performing pump and valve maintenance. Volume 1 describes the content requirements, format specifications, development procedures, and evaluation data for the job cards.

1995-01-24T23:59:59.000Z

434

Materials Science and Engineering B 117 (2005) 5361 Finite element analysis-based design of a fluid-flow control nano-valve  

E-Print Network (OSTI)

of a fluid-flow control nano-valve M. Grujicica,, G. Caoa, B. Pandurangana, W.N. Royb a Department A finite element method-based procedure is developed for the design of molecularly functionalized nano-size devices. The procedure is aimed at the single-walled carbon nano-tubes (SWCNTs) used in the construction

Grujicic, Mica

435

Energy Policy | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Public Services Energy Economy Energy Policy Energy Policy Energy Secretary Steven Chu speaks with President Barack Obama. | Energy Department Photo Energy Secretary Steven...

436

Renewable Energy | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Energy Renewable Energy October 7, 2013 - 9:16am Addthis Renewable energy increases energy security, creates jobs, and powers our clean energy economy. Renewable energy increases...

437

Annual Energy Outlook 2001 - Overview  

Gasoline and Diesel Fuel Update (EIA)

Overview Overview Key Energy Issues to 2020 Prices Consumption Energy Intensity Electricity Generation Production and Imports Carbon Dioxide Emissions Key Energy Issues to 2020 Currently, most attention in energy markets is focused on near-term issues of world oil supply and prices, U.S. natural gas prices, and the transition to restructured electricity markets in several regions of the country. The Annual Energy Outlook 2001 (AEO2001) addresses the longer-term trends of electricity industry restructuring, fossil fuel supply and prices, and the impacts of economic growth on projected energy use and carbon dioxide emissions. AEO2001 does not project short-term events, such as supply disruptions or severe weather. The AEO2001 projections assume a transition to full competitive pricing of

438

Development of glucose valves for metabolic engineering applications in E. coli  

E-Print Network (OSTI)

Microbial production platforms have extraordinary potential to help meet the energy, material and health needs of tomorrow. Through the reactions of cellular metabolism, microbes are an attractive option for the sustainable ...

Solomon, Kevin Val-Murvin

2012-01-01T23:59:59.000Z

439

U.S. Energy Information Administration (EIA) - Sector  

Gasoline and Diesel Fuel Update (EIA)

Issues in Focus Issues in Focus Introduction The "Issues in focus" section of the Annual Energy Outlook (AEO) provides an in-depth discussion on topics of special significance, including changes in assumptions and recent developments in technologies for energy production and consumption. Selected quantitative results are available in Appendix D. The first topic updates a discussion included in a number of previous AEOs that compared the Reference case to the results of two cases with different assumptions about the future course of existing energy policies. One case assumes the elimination of sunset provisions in existing energy policies; that is, the policies are assumed not to terminate as they would under current law. The other case assumes the extension or expansion

440

U.S. Energy Information Administration (EIA) - Sector  

Gasoline and Diesel Fuel Update (EIA)

Issues in Focus Issues in Focus Introduction The "Issues in focus" section of the Annual Energy Outlook (AEO) provides an in-depth discussion on topics of special significance, including changes in assumptions and recent developments in technologies for energy production and consumption. Selected quantitative results are available in Appendix D. The first topic updates a discussion included in a number of previous AEOs that compared the Reference case to the results of two cases with different assumptions about the future course of existing energy policies. One case assumes the elimination of sunset provisions in existing energy policies; that is, the policies are assumed not to terminate as they would under current law. The other case assumes the extension or expansion

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Global Insight Energy Group  

U.S. Energy Information Administration (EIA) Indexed Site

Outlook Outlook Mary Novak Managing Director IHS Global Insight Copyright © 2010 IHS Global Insight, Inc. Overview: Energy Sector Transformation Underway * The recession has hit energy demand hard, and aggregate energy demand is not expected to return to 2007 levels until 2018. * Oil and natural gas prices will both rise over the long-term, but the price trends will diverge with natural gas prices rising slowly due to the development of shale gas. * This forecast does not include a GHG cap-and-trade program. However, it is assumed that there will be continued improvement in equipment, appliance and building efficiencies that will reduce carbon emissions relative to past projections. * The forecast also includes the more than 30 state- level programs to increase efficiency and reduce

442

Conceptual Design of Optimized Fossil Energy Systems with Capture and Sequestration of Carbon Dioxide  

E-Print Network (OSTI)

Capacity factor Natural Gas Price ($/GJ) HHV Coal Price ($/of scale, energy prices (for natural gas, coal, biomass andprice for natural gas (assumed to be $6/MMBTU at the refueling station) and coal

Ogden, Joan M

2004-01-01T23:59:59.000Z

443

Optimal Control of Distributed Energy Resources and Demand Response under Uncertainty  

E-Print Network (OSTI)

and Demand Response under Uncertainty • F P t : wholesale natural gasdemand response and DER under uncertain electricity and natural gasand Demand Response under Uncertainty Energy Price Models We assume that the logarithms of the deseasonalized electricity and natural gas

Siddiqui, Afzal

2010-01-01T23:59:59.000Z

444

International Energy Outlook 2006 - Appendix G  

Gasoline and Diesel Fuel Update (EIA)

G G International Energy Outlook 2006 Appendix G: Key Assumptions for the IEO2006 Kyoto Protocol Case Energy-Related Emissions of Greenhouse Gases The System for the Analysis of Global energy Markets (SAGE)—the model used by EIA to prepare the IEO2006 mid-term projections—does not include non-energy-related emissions of greenhouse gases, which are estimated at about 15 to 20 percent of total greenhouse gas emissions, based on inventories submitted to the United Nations Framework Convention on Climate Change (UNFCCC). SAGE models global energy supply and demand and, therefore, does not address agricultural and other non-energy-related emissions. EIA implicitly assumes that percentage reductions of non-energy-related emissions and their associated abatement costs will be similar to those for energy-related emissions. Non-energy-related greenhouse gas emissions are likely to grow faster than energy-related emissions; however, the marginal abatement costs for non-energy-related greenhouse gas emissions are not known and cannot be estimated reliably. In SAGE, each region’s emissions reduction goal under the Kyoto Protocol is based only on the corresponding estimate of that region’s energy-related carbon dioxide emissions, as determined by EIA data. It is assumed that the required reductions will also be proportionately less than if all gases were included.

445

Theoretical Minimum Energy Use of a Building HVAC System  

E-Print Network (OSTI)

This paper investigates the theoretical minimum energy use required by the HVAC system in a particular code compliant office building. This limit might be viewed as the "Carnot Efficiency" for HVAC system. It assumes that all ventilation and air conditioning in the building are provided using the minimum energy value that does not violate physical law.

Tanskyi, O.

2011-01-01T23:59:59.000Z

446

CX-005795: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5795: Categorical Exclusion Determination 5795: Categorical Exclusion Determination CX-005795: Categorical Exclusion Determination New Hampshire-County-Belknap CX(s) Applied: B2.5, B5.1 Date: 05/02/2011 Location(s): Belknap, New Hampshire Office(s): Energy Efficiency and Renewable Energy Energy Efficiency and Conservation Block Grant Program. 1) Energy efficiency retrofits in County facilities, including building envelope improvements, thermostatically controlled radiator valves w/set-back capability, connect Old Wing Heating System to New Wing Heating System in the County Jail, and Water and Energy Conservation Measures throughout all County facilities (including Courthouse, built in 1893) and 2) upgrade building automation system in Nursing Home and replace hot water boilers in the County Jail.

447

CX-001560: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0: Categorical Exclusion Determination 0: Categorical Exclusion Determination CX-001560: Categorical Exclusion Determination Hydroelectric turbine at Water Treatment Plant American Recovery and Reinvestment Act Energy Efficiency and Conservation Block Grant Strategy Only CX(s) Applied: B5.1 Date: 03/31/2010 Location(s): Greensboro, North Carolina Office(s): Energy Efficiency and Renewable Energy, Golden Field Office Energy Efficiency and Conservation Block Grant funding. The Department of Energy funding will be used to install a reverse pump type hydroelectric turbine at the Mitchell Water Treatment Plant. A feasibility study has already been completed for the installation of this equipment. The turbine will generate electricity from the excess head that is currently burned at the plant with one butterfly control valve on each of the incoming raw

448

CX-005270: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

270: Categorical Exclusion Determination 270: Categorical Exclusion Determination CX-005270: Categorical Exclusion Determination Woburn Energy Efficiency Retrofits CX(s) Applied: B1.4, B2.2, B2.5, B5.1 Date: 02/17/2011 Location(s): Woburn, Massachusetts Office(s): Energy Efficiency and Renewable Energy Energy Efficiency and Conservation Block Grant Program. City Hall Retrofit Project: Lighting Fixture Retrofits and Fixture Controls; Building Envelope Improvement/Weatherization; Energy Management System/Temperature Setback; Steam Distribution System/Steam Trap Replacement; Heating System Upgrade/Pipe and Valve-Expansion Tank Insulation; Water Conservation DOCUMENT(S) AVAILABLE FOR DOWNLOAD CX-005270.pdf More Documents & Publications CX-005286: Categorical Exclusion Determination CX-009008: Categorical Exclusion Determination

449

CX-005270: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5270: Categorical Exclusion Determination 5270: Categorical Exclusion Determination CX-005270: Categorical Exclusion Determination Woburn Energy Efficiency Retrofits CX(s) Applied: B1.4, B2.2, B2.5, B5.1 Date: 02/17/2011 Location(s): Woburn, Massachusetts Office(s): Energy Efficiency and Renewable Energy Energy Efficiency and Conservation Block Grant Program. City Hall Retrofit Project: Lighting Fixture Retrofits and Fixture Controls; Building Envelope Improvement/Weatherization; Energy Management System/Temperature Setback; Steam Distribution System/Steam Trap Replacement; Heating System Upgrade/Pipe and Valve-Expansion Tank Insulation; Water Conservation DOCUMENT(S) AVAILABLE FOR DOWNLOAD CX-005270.pdf More Documents & Publications CX-003712: Categorical Exclusion Determination CX-009008: Categorical Exclusion Determination

450

(001) textured L1{sub 0}-FePt pseudo spin valve with TiN spacer  

Science Conference Proceedings (OSTI)

TiN was investigated as a potential spacer material in L1{sub 0}-FePt based pseudo spin valves (PSV). PSVs with the structure MgO/L1{sub 0}-Fe{sub 50}Pt{sub 50} (20 nm)/TiN (5 nm)/L1{sub 0}-Fe{sub 50}Pt{sub 50} (x nm) were fabricated, where x was varied from 5 to 20 nm. The highest giant magnetoresistance (GMR) ratio of 0.61% was obtained for the PSV with a top L1{sub 0}-FePt thickness of 20 nm. Contributions to the GMR arose from both the spin dependent scattering at the FePt/TiN interfaces and domain wall resistivity. Magnon magnetoresistance was also observed in the fabricated PSVs.

Ho, P. [Department of Materials Science and Engineering, National University of Singapore, 117576 Singapore (Singapore) and Data Storage Institute, Agency of Science, Technology and Research (A-STAR), 117608 Singapore (Singapore); Han, G. C. [Data Storage Institute, Agency of Science, Technology and Research (A-STAR), 117608 Singapore (Singapore); He, K. H.; Chow, G. M.; Chen, J. S. [Department of Materials Science and Engineering, National University of Singapore, 117576 Singapore (Singapore)

2011-12-19T23:59:59.000Z

451

Matter & Energy Solar Energy  

E-Print Network (OSTI)

See Also: Matter & Energy Solar Energy· Electronics· Materials Science· Earth & Climate Energy at the University of Illinois, the future of solar energy just got brighter. Although silicon is the industry Electronics Over 1.2 Million Electronics Parts, Components and Equipment. www.AlliedElec.com solar energy

Rogers, John A.

452

Energy Efficiency & Renewable Energy  

E-Print Network (OSTI)

Energy Efficiency & Renewable Energy 2009 WIND TECHNOLOGIES MARKET REPORT AUGUST 2010 #12;2009 Wind Associates) Suzanne Tegen (National Renewable Energy Laboratory) Table of Contents Acknowledgments' Association); Ed DeMeo (Renewable Energy Consulting Services, Inc.); Mike O'Sullivan (NextEra Energy Resources

453

Steam distribution and energy delivery optimization using wireless sensors  

Science Conference Proceedings (OSTI)

The Extreme Measurement Communications Center at Oak Ridge National Laboratory (ORNL) explores the deployment of a wireless sensor system with a real-time measurement-based energy efficiency optimization framework in the ORNL campus. With particular focus on the 12-mile long steam distribution network in our campus, we propose an integrated system-level approach to optimize the energy delivery within the steam distribution system. We address the goal of achieving significant energy-saving in steam lines by monitoring and acting on leaking steam valves/traps. Our approach leverages an integrated wireless sensor and real-time monitoring capabilities. We make assessments on the real-time status of the distribution system by mounting acoustic sensors on the steam pipes/traps/valves and observe the state measurements of these sensors. Our assessments are based on analysis of the wireless sensor measurements. We describe Fourier-spectrum based algorithms that interpret acoustic vibration sensor data to characterize flows and classify the steam system status. We are able to present the sensor readings, steam flow, steam trap status and the assessed alerts as an interactive overlay within a web-based Google Earth geographic platform that enables decision makers to take remedial action. We believe our demonstration serves as an instantiation of a platform that extends implementation to include newer modalities to manage water flow, sewage and energy consumption.

Olama, Mohammed M [ORNL; Allgood, Glenn O [ORNL; Kuruganti, Phani Teja [ORNL; Sukumar, Sreenivas R [ORNL; Djouadi, Seddik M [ORNL; Lake, Joe E [ORNL

2011-01-01T23:59:59.000Z

454

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

91 - 25800 of 31,917 results. 91 - 25800 of 31,917 results. Download CX-005102: Categorical Exclusion Determination Spectroscopic Measurement of IsoparL in Supernate and Dilute Nitric Acid CX(s) Applied: B3.6 Date: 01/12/2011 Location(s): Aiken, South Carolina Office(s): Savannah River Operations Office http://energy.gov/nepa/downloads/cx-005102-categorical-exclusion-determination Download CX-005103: Categorical Exclusion Determination Operation of Zeiss Sigma VP Scanning Electron Microscope (SEM) CX(s) Applied: B3.6 Date: 01/12/2011 Location(s): Aiken, South Carolina Office(s): Savannah River Operations Office http://energy.gov/nepa/downloads/cx-005103-categorical-exclusion-determination Download CX-005104: Categorical Exclusion Determination 221-H Warm Gang Valve Corridor Section 9 Air Conditioner Replacement Unit

455

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

91 - 26400 of 28,560 results. 91 - 26400 of 28,560 results. Download CX-007634: Categorical Exclusion Determination Replace 802-H Platform/Control Valve Ladder with New Lapeyre Stairs CX(s) Applied: B2.5 Date: 01/19/2012 Location(s): South Carolina Offices(s): Savannah River Operations Office http://energy.gov/nepa/downloads/cx-007634-categorical-exclusion-determination Download CX-007635: Categorical Exclusion Determination Scaled Saltstone Mixer Commissioning CX(s) Applied: B3.6 Date: 01/18/2012 Location(s): South Carolina Offices(s): Savannah River Operations Office http://energy.gov/nepa/downloads/cx-007635-categorical-exclusion-determination Download CX-007636: Categorical Exclusion Determination Dynamic Mechanical Testing with Battery Electrolyte in Savannah River National Laboratory Designed Sample Holders

456

Energy Efficiency and Conservation Block Grant Program  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

NH-County-Belknap NH-County-Belknap Location: County NH American Recovery and Reinvestment Act: Proposed Action or Project Description: 1) Energy efficiency retrofits in County facilities, including building envelope improvements, thermostatically controlled radiator valves w/set-back capability, connect Old Wing Heating System to New Wing Heating System in the County Jail, and Water & Energy Conservation Measures throughout all County facilities (including Courthouse, built in 1893) and 2) upgrade building automation system in Nursing Home and replace hot water boilers in the County Jail. Conditions: None Categorical Exclusion(s) Applied: B2.5, B5.1 *-For the complete DOE National Environmental Policy Act regulations regarding categorical exclusions, see Subpart D of 10 CFR10 21

457

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

31 - 21840 of 26,764 results. 31 - 21840 of 26,764 results. Download CX-008342: Categorical Exclusion Determination Replace Big Hill Raw Water Intake System Oil Water Separator Tank with Concrete Tank GFE CX(s) Applied: B1.3 Date: 05/18/2012 Location(s): Texas Offices(s): Strategic Petroleum Reserve Field Office http://energy.gov/nepa/downloads/cx-008342-categorical-exclusion-determination Download CX-008343: Categorical Exclusion Determination Access to Remote Valve Station West Hackberry -2 CX(s) Applied: B1.3 Date: 05/18/2012 Location(s): Louisiana Offices(s): Strategic Petroleum Reserve Field Office http://energy.gov/nepa/downloads/cx-008343-categorical-exclusion-determination Download CX-008344: Categorical Exclusion Determination Clean, Seal, and Paint West Hackberry Buildings RW MCC 392, Substation 390

458

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

31 - 9340 of 28,560 results. 31 - 9340 of 28,560 results. Download CX-007507: Categorical Exclusion Determination Record of Categorical Exclusion for Inspection and Repair of West Hackberry-SUN 42-inch Crude Oil Pipeline CX(s) Applied: B1.3 Date: 11/28/2011 Location(s): Louisiana Offices(s): Strategic Petroleum Reserve Field Office http://energy.gov/nepa/downloads/cx-007507-categorical-exclusion-determination Download CX-007508: Categorical Exclusion Determination Record of Categorical Exclusion for Rework Bryan Mound Seaway Dock Terminal Bypass Valve MOV-C308 CX(s) Applied: B1.3 Date: 11/16/2011 Location(s): Texas Offices(s): Strategic Petroleum Reserve Field Office http://energy.gov/nepa/downloads/cx-007508-categorical-exclusion-determination Download CX-007509: Categorical Exclusion Determination

459

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

81 - 8690 of 29,416 results. 81 - 8690 of 29,416 results. Download CX-001368: Categorical Exclusion Determination Repair Domestic Water Leak North of 719-18A CX(s) Applied: B1.3 Date: 03/16/2010 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office http://energy.gov/nepa/downloads/cx-001368-categorical-exclusion-determination Download CX-001369: Categorical Exclusion Determination Repair Firewater Line in B-Area East Side (Road C-2) near Post Indicator Valve 2118 CX(s) Applied: B1.3 Date: 03/16/2010 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office http://energy.gov/nepa/downloads/cx-001369-categorical-exclusion-determination Download CX-001370: Categorical Exclusion Determination Repair Water Leak at 607-59G at Central Sanitary Wastewater Plant

460

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

21 - 6730 of 28,905 results. 21 - 6730 of 28,905 results. Download CX-005807: Categorical Exclusion Determination Radiological Evidence Examination Facility (REEF) Full Activation Scenario Training Exercise CX(s) Applied: B3.6 Date: 03/29/2011 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office http://energy.gov/nepa/downloads/cx-005807-categorical-exclusion-determination Download CX-005813: Categorical Exclusion Determination Fire Department Personnel to Perform Annual Flush of Hydrants and Prove Curb Valves CX(s) Applied: B1.3 Date: 03/29/2011 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office http://energy.gov/nepa/downloads/cx-005813-categorical-exclusion-determination Download CX-005822: Categorical Exclusion Determination

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

41 - 27650 of 28,904 results. 41 - 27650 of 28,904 results. Download CX-010112: Categorical Exclusion Determination High Pressure Valve Cycle Testing Using Hydrogen at 723-A CX(s) Applied: B3.6 Date: 03/28/2013 Location(s): South Carolina Offices(s): Savannah River Operations Office http://energy.gov/nepa/downloads/cx-010112-categorical-exclusion-determination Download CX-010113: Categorical Exclusion Determination Compression Stress Relaxometer CX(s) Applied: B3.6 Date: 03/28/2013 Location(s): South Carolina Offices(s): Savannah River Operations Office http://energy.gov/nepa/downloads/cx-010113-categorical-exclusion-determination Download CX-010114: Categorical Exclusion Determination Sable Systems Oxzilla Oxygen Analyzer CX(s) Applied: B3.6 Date: 03/28/2013 Location(s): South Carolina Offices(s): Savannah River Operations Office

462

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

01 - 7310 of 26,764 results. 01 - 7310 of 26,764 results. Download CX-008348: Categorical Exclusion Determination Replace Big Hill Raw Water Intake System Oil Water Separator Tank with Concrete Tank CX(s) Applied: B1.3 Date: 04/16/2012 Location(s): Louisiana Offices(s): Strategic Petroleum Reserve Field Office http://energy.gov/nepa/downloads/cx-008348-categorical-exclusion-determination Download CX-008349: Categorical Exclusion Determination Replacement Anode Bed on West Hackberry 42-inch Crude Oil Pipeline at Gum Cove Road CX(s) Applied: B1.3 Date: 04/10/2012 Location(s): Louisiana Offices(s): Strategic Petroleum Reserve Field Office http://energy.gov/nepa/downloads/cx-008349-categorical-exclusion-determination Download CX-008350: Categorical Exclusion Determination Re-work Bryan Mound 30" Crude Oil Pipeline Mainline Valves

463

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

91 - 14300 of 29,416 results. 91 - 14300 of 29,416 results. Download CX-010485: Categorical Exclusion Determination Replace Salt Disposal Unit 2/Vault 4 Grout Line Diverter Valve with Spool Piece CX(s) Applied: B1.3 Date: 05/29/2013 Location(s): South Carolina Offices(s): Savannah River Operations Office http://energy.gov/nepa/downloads/cx-010485-categorical-exclusion-determination Download CX-010486: Categorical Exclusion Determination Installation Support of Supplemental Ventilation at Tank 15 CX(s) Applied: B2.5 Date: 05/29/2013 Location(s): South Carolina Offices(s): Savannah River Operations Office http://energy.gov/nepa/downloads/cx-010486-categorical-exclusion-determination Download CX-010487: Categorical Exclusion Determination Defense Waste Processing Facility Precipitate Reactor Feed Tank (PRFT)

464

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

71 - 27680 of 28,904 results. 71 - 27680 of 28,904 results. Download CX-010309: Categorical Exclusion Determination 730-1B Vehicle Charging Station CX(s) Applied: B1.32 Date: 04/26/2013 Location(s): South Carolina Offices(s): Savannah River Operations Office http://energy.gov/nepa/downloads/cx-010309-categorical-exclusion-determination Download CX-010310: Categorical Exclusion Determination Tanks 13 and 15 Soil Samples for Transfer Line Future Design CX(s) Applied: B3.1 Date: 04/26/2013 Location(s): South Carolina Offices(s): Savannah River Operations Office http://energy.gov/nepa/downloads/cx-010310-categorical-exclusion-determination Download CX-010311: Categorical Exclusion Determination Tank 7 Center Riser Install/Remove Temporary Isolation Valve V-8 CX(s) Applied: B1.3 Date: 04/26/2013

465

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

41 - 25750 of 31,917 results. 41 - 25750 of 31,917 results. Download CX-001369: Categorical Exclusion Determination Repair Firewater Line in B-Area East Side (Road C-2) near Post Indicator Valve 2118 CX(s) Applied: B1.3 Date: 03/16/2010 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office http://energy.gov/nepa/downloads/cx-001369-categorical-exclusion-determination Download CX-001371: Categorical Exclusion Determination Synthetic Concentrators CX(s) Applied: B3.6 Date: 03/16/2010 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office http://energy.gov/nepa/downloads/cx-001371-categorical-exclusion-determination Download CX-001182: Categorical Exclusion Determination Access Road Improvement Project for Structure 12/1 of the Snoking Tap to

466

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

61 - 30770 of 31,917 results. 61 - 30770 of 31,917 results. Download CX-008732: Categorical Exclusion Determination Idaho National Laboratory (INL) Administration Building (IAB) Communication Room Heating, Ventilation, and Air Conditioning (HVAC) Upgrade CX(s) Applied: B1.31 Date: 05/21/2012 Location(s): Idaho Offices(s): Idaho Operations Office http://energy.gov/nepa/downloads/cx-008732-categorical-exclusion-determination Download CX-008758: Categorical Exclusion Determination Advanced Test Reactor (ATR) Primary Coolant System (PCS) Relief Valves Monorail System CX(s) Applied: B1.31 Date: 05/14/2012 Location(s): Idaho Offices(s): Idaho Operations Office http://energy.gov/nepa/downloads/cx-008758-categorical-exclusion-determination Download CX-008759: Categorical Exclusion Determination Information Operations & Research Center (IORC) Room E-6 Air Conditioner

467

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

01 - 25710 of 28,560 results. 01 - 25710 of 28,560 results. Download CX-010485: Categorical Exclusion Determination Replace Salt Disposal Unit 2/Vault 4 Grout Line Diverter Valve with Spool Piece CX(s) Applied: B1.3 Date: 05/29/2013 Location(s): South Carolina Offices(s): Savannah River Operations Office http://energy.gov/nepa/downloads/cx-010485-categorical-exclusion-determination Download CX-010486: Categorical Exclusion Determination Installation Support of Supplemental Ventilation at Tank 15 CX(s) Applied: B2.5 Date: 05/29/2013 Location(s): South Carolina Offices(s): Savannah River Operations Office http://energy.gov/nepa/downloads/cx-010486-categorical-exclusion-determination Download CX-010487: Categorical Exclusion Determination Defense Waste Processing Facility Precipitate Reactor Feed Tank (PRFT)

468

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

401 - 14410 of 29,416 results. 401 - 14410 of 29,416 results. Download CX-007632: Categorical Exclusion Determination Actinide Removal Process/Modular Caustic Side Solvent Extraction Unit Salt Batch Qualification CX(s) Applied: B3.6 Date: 01/19/2012 Location(s): South Carolina Offices(s): Savannah River Operations Office http://energy.gov/nepa/downloads/cx-007632-categorical-exclusion-determination Download CX-007633: Categorical Exclusion Determination Tank 50 Formulation Treatability Study CX(s) Applied: B3.6 Date: 01/19/2012 Location(s): South Carolina Offices(s): Savannah River Operations Office http://energy.gov/nepa/downloads/cx-007633-categorical-exclusion-determination Download CX-007634: Categorical Exclusion Determination Replace 802-H Platform/Control Valve Ladder with New Lapeyre Stairs

469

Save energy | ENERGY STAR  

NLE Websites -- All DOE Office Websites (Extended Search)

energy Stamp out energy waste Find cost-effective investments Engage occupants Purchase energy-saving products Put computers to sleep Get help from an expert Take a comprehensive...

470

Energy Basics: Ocean Energy Technologies  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Energy Basics Renewable Energy Printable Version Share this resource Biomass Geothermal Hydrogen Hydropower Ocean Ocean Thermal Energy Conversion Tidal Energy Wave Energy...

471

Plant energy auditing | ENERGY STAR  

NLE Websites -- All DOE Office Websites (Extended Search)

track, and benchmark Improve energy performance ENERGY STAR industrial partnership Energy guides Energy efficiency and air regulation Plant energy auditing Industrial...

472

Improve energy performance | ENERGY STAR  

NLE Websites -- All DOE Office Websites (Extended Search)

track, and benchmark Improve energy performance ENERGY STAR industrial partnership Energy guides Energy efficiency and air regulation Plant energy auditing Industrial...

473

Optimal Energy Allocation for Wireless Communications with Energy Harvesting Constraints  

E-Print Network (OSTI)

We consider the use of energy harvesters, in place of conventional batteries with fixed energy storage, for point-to-point wireless communications. In addition to the challenge of transmitting in a channel with time selective fading, energy harvesters provide a perpetual but unreliable energy source. In this paper, we consider the problem of energy allocation over a finite horizon, taking into account channel conditions and energy sources that are time varying, so as to maximize the throughput. Two types of side information (SI) on the channel conditions and harvested energy are assumed to be available: causal SI (of the past and present slots) and full SI (of the past, present and future slots). We obtain structural results for the optimal energy allocation, via the use of dynamic programming and convex optimization techniques. In particular, if unlimited energy can be stored in the battery with harvested energy and full SI is available, we prove the optimality of a water-filling energy allocation solution w...

Ho, Chin Keong

2011-01-01T23:59:59.000Z

474

LOWER BOUNDS ON ENERGY DISSIPATION AND NOISE-TOLERANCE FOR DEEP SUBMICRON VLSIy  

E-Print Network (OSTI)

of observing a '1' at the output. Lemma 1: The energy dissipation is minimum when I(X Y)fc = R. For a symmetric bound on supply voltage and circuit speed. We then provide a lower bound on total energy dissipation consider the problem of jointly optimizing static and dy- namic components of energy dissipation. We assume

Shanbhag, Naresh R.

475

CX-007370: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

370: Categorical Exclusion Determination 370: Categorical Exclusion Determination CX-007370: Categorical Exclusion Determination Idaho-TRIBE-SHOSHONE-BANNOCK TRIBE OF THE FORT HALL RESERVATION OF IDAHO CX(s) Applied: B2.5, B5.1 Date: 11/22/2011 Location(s): Idaho Offices(s): Energy Efficiency and Renewable Energy Energy Efficiency and Conservation Block Grant Program. The Shoshone Bannock Tribes of Idaho proposes to conduct energy efficient building retrofits on three public buildings (Tribal Business Center, Human Resource Development Center, and Timbee Hall Recreation Center). Retrofits proposed include replacing/upgrading control valves, in-core monitoring devices, facility air filtration systems; lowering programmable thermostat settings; placing timers on hot water heaters; installing solar water heating

476

CX-002979: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

979: Categorical Exclusion Determination 979: Categorical Exclusion Determination CX-002979: Categorical Exclusion Determination Oregon Energy Efficiency and Conservation Block Grant Formula - City of Winston CX(s) Applied: B2.5, B1.3 Date: 07/12/2010 Location(s): Winston, Oregon Office(s): Energy Efficiency and Renewable Energy, Golden Field Office The City of Winston, Oregon proposes to use $240,000 of Energy Efficiency and Conservation Block Grant (EECBG) funding towards the total cost of a proposed wastewater pumping retrofit project at a sewer lift station. The current sewer lift station design incorporates three 110 horsepower (HP) pumps which currently do not work well at low flows, where pumps are running constantly and against throttling valves. The proposed project would replace one of the 110 HP pumps with a 25 HP pump (85 HP reduction),

477

CX-003990: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0: Categorical Exclusion Determination 0: Categorical Exclusion Determination CX-003990: Categorical Exclusion Determination Greenhouse Gas to Energy Projects CX(s) Applied: B5.1 Date: 09/22/2010 Location(s): Robeson County, North Carolina Office(s): Energy Efficiency and Renewable Energy, Golden Field Office Robeson County is proposing to use Energy Efficiency and Conservation Block Grant funding to expand the existing landfill gas collection system and construct an electricity-generating facility onsite. The gas collection system construction will consist primarily of installing 24 new extraction wells, approximately 9,000 linear feet of high-density polyethylene piping, a condensate removal vessel and 4 isolation valves. Funding will also be used for the electricity generating facility which will have an estimated

478

Categorical Exclusion Determinations: B2.5 | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

June 17, 2010 June 17, 2010 CX-002764: Categorical Exclusion Determination Arkansas-City-Fayetteville CX(s) Applied: B2.5, A1, A9, A11, B5.1 Date: 06/17/2010 Location(s): Fayetteville, Arkansas Office(s): Energy Efficiency and Renewable Energy June 16, 2010 CX-002991: Categorical Exclusion Determination Installation of Turbidity Meter Discharge Check Valves CX(s) Applied: B2.5 Date: 06/16/2010 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office June 16, 2010 CX-002784: Categorical Exclusion Determination Utah-County-Washington CX(s) Applied: B2.5, B5.1 Date: 06/16/2010 Location(s): Washington County, Utah Office(s): Energy Efficiency and Renewable Energy June 15, 2010 CX-002776: Categorical Exclusion Determination California-City-Elk Grove

479

Energy Efficiency & Renewable Energy  

E-Print Network (OSTI)

of energy; · increase efficiency and productivity of the existing energy infrastructure; · bring clean lives of Americans by productively enhancing their energy choices and quality of life. Energy Efficiency Performance and Sustainable Buildings by 2015 Design all new Federal buildings which begin the planning

480

Energy Conservation Renewable Energy  

E-Print Network (OSTI)

Energy Conservation Renewable Energy The Future at Rutgers University Facilities & Capital Planning Operations & Services Utilities Operations 6 Berrue Circle Piscataway, NJ 08854 #12;Energy Conservation Wh C ti ? R bl EWhy Conservation? Renewable Energy · Climate control reduces green house gases · Reduces

Delgado, Mauricio

Note: This page contains sample records for the topic "valves assumed energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Wormhole solutions supported by interacting dark matter and dark energy  

E-Print Network (OSTI)

We show that the presence of a nonminimal interaction between dark matter and dark energy may lead to a violation of the null energy condition and to the formation of a configuration with nontrivial topology (a wormhole). In this it is assumed that both dark matter and dark energy satisfy the null energy condition, a violation of which takes place only in the inner high-density regions of the configuration. This is achieved by assuming that, in a high-density environment, a nonminimal coupling function changes its sign in comparison with the case where dark matter and dark energy have relatively low densities which are typical for a cosmological background. For this case, we find regular static, spherically symmetric solutions describing wormholes supported by dark matter nonminimally coupled to dark energy in the form of a quintessence scalar field.

Folomeev, Vladimir

2013-01-01T23:59:59.000Z

482

Wormhole solutions supported by interacting dark matter and dark energy  

E-Print Network (OSTI)

We show that the presence of a nonminimal interaction between dark matter and dark energy may lead to a violation of the null energy condition and to the formation of a configuration with nontrivial topology (a wormhole). In this it is assumed that both dark matter and dark energy satisfy the null energy condition, a violation of which takes place only in the inner high-density regions of the configuration. This is achieved by assuming that, in a high-density environment, a nonminimal coupling function changes its sign in comparison with the case where dark matter and dark energy have relatively low densities which are typical for a cosmological background. For this case, we find regular static, spherically symmetric solutions describing wormholes supported by dark matter nonminimally coupled to dark energy in the form of a quintessence scalar field.

Vladimir Folomeev; Vladimir Dzhunushaliev

2013-08-13T23:59:59.000Z

483

Japan's Long-term Energy Demand and Supply Scenario to 2050 - Estimation for the Potential of Massive CO2 Mitigation  

E-Print Network (OSTI)

energy sources for 20%, hydro power for 10% and fossil-firedetc. • Wind power • Solar • Geothermal ^ Hydro O LO CO CT> Chydro and geothermal) are assumed to expand their share of electric utilities' power

Komiyama, Ryoichi

2010-01-01T23:59:59.000Z

484

Evaluation of battery/microturbine hybrid energy storage technologies at the University of Maryland :a study for the DOE Energy Storage Systems Program.  

DOE Green Energy (OSTI)

This study describes the technical and economic benefits derived from adding an energy storage component to an existing building cooling, heating, and power system that uses microturbine generation to augment utility-provided power. Three different types of battery energy storage were evaluated: flooded lead-acid, valve-regulated lead-acid, and zinc/bromine. Additionally, the economic advantages of hybrid generation/storage systems were evaluated for a representative range of utility tariffs. The analysis was done using the Distributed Energy Technology Simulator developed for the Energy Storage Systems Program at Sandia National Laboratories by Energetics, Inc. The study was sponsored by the U.S. DOE Energy Storage Systems Program through Sandia National Laboratories and was performed in coordination with the University of Maryland's Center for Environmental Energy Engineering.

De Anda, Mindi Farber (Energetics, Inc., Washington, DC); Fall, Ndeye K. (Energetics, Inc., Washington, DC)

2005-03-01T23:59:59.000Z

485

About the Geometric Solution to the Problems of Dark Energy  

E-Print Network (OSTI)

In this paper is proposed a geometric solution to the dark energy, assuming that the space can be divided into regions of size $\\sim L_{p}$ and energy $\\sim E_{p}$. Significantly this assumption generate a energy density similar to the energy density observed for the vaccum energy, the correct solution for the coincidence problem and the state equation characteristic of quintessence in the comoving coordinates. Similarly is studied the ultraviolet and infrarred limits and the amount of dark energy in the Universe.

Miguel Angel García-Aspeitia

2010-11-19T23:59:59.000Z

486

Office of Energy Efficiency and Renewable Energy  

E-Print Network (OSTI)

Operated by the Alliance for Sustainable Energy, LLC Contract No. DE-AC36-08-GO28308NOTICE This report was prepared as an account of work sponsored by an agency of the United States government. Neither the United States government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States government or any agency thereof. The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States government or any agency thereof. Available electronically at

Th Edition; Lori Bird; Claire Kreycik; Barry Friedman

2008-01-01T23:59:59.000Z

487

Office of Energy Efficiency and Renewable Energy  

E-Print Network (OSTI)

Operated by the Alliance for Sustainable Energy, LLC Contract No. DE-AC36-08-GO28308NOTICE This report was prepared as an account of work sponsored by an agency of the United States government. Neither the United States government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States government or any agency thereof. The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States government or any agency thereof. Available electronically at

Paul Schwabe; Karlynn Cory; Paul Schwabe; Karlynn Cory; James Newcomb

2009-01-01T23:59:59.000Z

488

Energy Education  

Science Conference Proceedings (OSTI)

Mar 6, 2013 ... Energy Technologies and Carbon Dioxide Management: Energy Education .... A Suggestion for Establishing Energy Management Policy in ...

489

Energy Portal  

Science Conference Proceedings (OSTI)

NIST Home > Energy Portal. Energy Portal - Overview. ... see all Energy programs and projects ... Instruments. Nonlinear Optical Spectroscopy ...

2013-11-07T23:59:59.000Z

490

Annual Energy Outlook Evaluation, 2005  

Gasoline and Diesel Fuel Update (EIA)

Outlook Evaluation, 2005 1 Outlook Evaluation, 2005 1 Annual Energy Outlook Evaluation, 2005 * Then Energy Information Administration (EIA) produces projections of energy supply and demand each year in the Annual Energy Outlook (AEO). The projections in the AEO are not statements of what will happen but of what might happen, given the assumptions and methodologies used. The projections are business-as-usual trend projections, given known technology, technological and demographic trends, and current laws and regulations. Thus, they provide a policy-neutral reference case that can be used to analyze policy initiatives. EIA does not propose or advocate future legislative and regulatory changes. All laws are assumed to remain as currently enacted; however, the impacts of emerging regulatory changes,

491

Wet Corn Milling Energy Guide  

NLE Websites -- All DOE Office Websites (Extended Search)

307 307 ERNEST ORLANDO LAWRENCE BERKELEY NATIONAL LABORATORY Energy Efficiency Improvement and Cost Saving Opportunities for the Corn Wet Milling Industry An ENERGY STAR Guide for Energy and Plant Managers Christina Galitsky, Ernst Worrell and Michael Ruth Environmental Energy Technologies Division Sponsored by the U.S. Environmental Protection Agency July 2003 Disclaimer This document was prepared as an account of work sponsored by the United States Government. While this document is believed to contain correct information, neither the United States Government nor any agency thereof, nor The Regents of the University of California, nor any of their employees, makes any warranty, express or implied, or assumes any legal responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product,

492

Reactivity transients during a blowdown in a MSIV (Main Steam Isolation Valves) closure ATWS (Anticipated Transients Without Scram)  

SciTech Connect

The objectives of this work are to study the consequences of the reactivity transients during a blowdown in an ATWS event with closure of the Main Steam Isolation Valves (MSIV), and to evaluate the effect of the LPCI (Low Pressure Coolant Injection) system and the sensitivity of plant response to the feedback coefficients. The present work was performed with the BNL Plant Analyzer (BPA). The BPA is a on-line, interactive BWR system code which models the non-homogeneous, non-equilibrium two-phase flow with a drift flux mixture model, the reactor kinetics with a point kinetic model, the thermal