National Library of Energy BETA

Sample records for v-10 additional description

  1. T-585: Mac OS X v10.6.7 Security Update 2011-001

    Broader source: Energy.gov [DOE]

    Mac OS Update: Mac OS 10.6.7 fixes multiple vulnerabilities in the following release. This update can be installed on non-startup volumes, but you should only do this if the current startup volume has already been updated to Mac OS X Server v10.6.7. The simplest way to avoid issues from an improper installation is to start up from the volume that you wish to update.

  2. Development of membranes for hydrogen separation: Pd-coated V-10Pd

    SciTech Connect (OSTI)

    Paglieri, Stephen N; Wermer, Joseph R; Buxbaum, Robert E; Ciocco, Michael V; Howard, Bret H; Morreale, Bryan D

    2009-01-01

    Numerous Group IVB and VB alloys were prepared and tested as potential membrane materials but most of these materials were brittle or exhibited cracking during hydrogen exposure. One of the more ductile alloys, V-10Pd (at. %), was fabricated into a thin (107-{micro}m thick) composite membrane coated with 100 nm of Pd on each side. The material was tested for hydrogen permeability, resistance to hydrogen embrittlement, and long term hydrogen flux stability. The hydrogen permeability, {phi}, of the V-10Pd membrane was 3.86 x 10{sup -8} mol H{sub 2} m{sup -1} s{sup -1} Pa{sup -0.5} (avg. of three different samples) at 400 C, which is slightly higher than the permeability of Pd-23Ag at that temperature. A 1400 h hydrogen flux test at 400 C demonstrated that the rate of metallic interdiffusion was slow between the V-10Pd foil and the 100-nm-thick Pd coating on the surface. However, at the end of testing the membrane cracked at 118 C because of hydrogen embrittlement.

  3. Testbed Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Testbed Description Network R&D Overview Experimental Network Testbeds 100G SDN Testbed Testbed Description Testbed Results Proposal Process Terms and Conditions Dark Fiber Testbed...

  4. Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Program Description Inspiring girls to recognize their potential and pursue opportunities in science, technology, engineering and mathematics. Through Expanding Your Horizon (EYH) ...

  5. Testbed Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Testbed Description Network R&D Software-Defined Networking (SDN) Experimental Network Testbeds 100G SDN Testbed Testbed Description Proposal Process Terms and Conditions Dark Fiber Testbed Test Circuit Service Testbed Results Current Testbed Research Previous Testbed Research Performance (perfSONAR) Software & Tools Development Data for Researchers Partnerships Publications Workshops Contact Us Technical Assistance: 1 800-33-ESnet (Inside US) 1 800-333-7638 (Inside US) 1 510-486-7600

  6. PES-v10

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    An Embedded Communication Network Simulator for Power Systems Simulations in PSCAD Neda Nasiriani, Roopa Ramachandran,Kaveh Rahimi Yaser P. Fallah, Parviz Famouri Lane Dept. of Computer Science & Electrical Engineering West Virginia University Morgantown, WV, USA Steve Bossart, Keith Dodrill US Department of Energy, National Energy Technology Laboratory (NETL) Morgantown, WV, USA Abstract-The emergence of distributed communication based control schemes in power systems emphasizes the need

  7. PES-v10

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... can be read from a delay profile; this profile can be ... Initially the wind component acts as a load due to the low ... and Standards," Industrial Informatics, IEEE ...

  8. Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Program Description SAGE, the Summer of Applied Geophysical Experience, is a unique educational program designed to introduce students in geophysics and related fields to "hands on" geophysical exploration and research. The program emphasizes both teaching of field methods and research related to basic science and a variety of applied problems. SAGE is hosted by the National Security Education Center and the Earth and Environmental Sciences Division of the Los Alamos National

  9. Additive Manufacturing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MST » MST Research Programs » Additive Manufacturing Additive Manufacturing A method allowing unparalleled manufacturing control, data visualization, and high-value parts repair. Through additive manufacturing, Los Alamos is developing materials for the future. Taking complex manufacturing challenges from design to fabrication. A science and engineering approach for additive manufacturing solutions. Get Expertise John Carpenter Technical Staff Member Metallurgy Email Division Leader Materials

  10. Additive Manufacturing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    manufacturing and national security To realize additive manufacturing's potential as a disruptive technology for Los Alamos National Laboratory's national security missions,...

  11. additive manufacturuing

    National Nuclear Security Administration (NNSA)

    an award last month for his 3D printing innovation. It could revolutionize additive manufacturing.

    Lawrence Livermore Lab engineer Bryan Moran wasn't necessarily...

  12. Mass Transfer And Hydraulic Testing Of The V-05 And V-10 Contactors With The Next Generation Solvent

    SciTech Connect (OSTI)

    Herman, D. T.; Duignan, M. R.; Williams, M. R.; Peters, T. B.; Poirier, M. R.; Fondeur, F. F.

    2013-07-31

    The Modular Caustic Side Solvent Extraction (CSSX) Unit (MCU) facility is actively pursuing the transition from the current BOBCalixC6 based solvent to the Next Generation Solvent (NGS)-MCU solvent. To support this integration of NGS into the MCU facilities, Savannah River Remediation (SRR) requested that Savannah River National Laboratory (SRNL) perform testing of a blend of the NGS (MaxCalix based solvent) with the current solvent (BOBCalixC6 based solvent) for the removal of cesium (Cs) from the liquid salt waste stream. This testing differs from prior testing by utilizing a blend of BOBCalixC6 based solvent and the NGS with the full (0.05 M) concentration of the MaxCalix as well as a new suppressor, tris(3,7dimethyloctyl) guanidine. Single stage tests were conducted using the full size V-05 and V-10 centrifugal contactors installed at SRNL. These tests were designed to determine the mass transfer and hydraulic characteristics with the NGS solvent blended with the projected heel of the BOBCalixC6 based solvent that will exist in MCU at time of transition. The test program evaluated the amount of organic carryover and the droplet size of the organic carryover phases using several analytical methods. Stage efficiency and mass distribution ratios were determined by measuring Cs concentration in the aqueous and organic phases during single contactor testing. The nominal cesium distribution ratio, D(Cs) measured for extraction ranged from 37-60. The data showed greater than 96% stage efficiency for extraction. No significant differences were noted for operations at 4, 8 or 12 gpm aqueous salt simulant feed flow rates. The first scrub test (contact with weak caustic solution) yielded average scrub D(Cs) values of 3.3 to 5.2 and the second scrub test produced an average value of 1.8 to 2.3. For stripping behavior, the first stage D Cs) values ranged from 0.04 to 0.08. The efficiency of the low flow (0.27 gpm aqueous) was calculated to be 82.7%. The Spreadsheet Algorithm for Stagewise Solvent Extraction (SASSE) predicted equivalent DF for MCU from this testing is greater than 3,500 assuming 95% efficiency during extraction and 80% efficiency during scrub and strip. Hydraulically, the system performed very well in all tests. Target flows were easily obtained and stable throughout testing. Though some issues were encountered with plugging in the coalescer, they were not related to the solvent. No hydraulic upsets due to the solvent were experienced during any of the tests conducted. The first extraction coalescer element used in testing developed high pressure drop that made it difficult to maintain the target flow rates. Analysis showed an accumulation of sodium aluminosilicate solids. The coalescer was replaced with one from the same manufacturers lot and pressure drop was no longer an issue. Concentrations of Isopar L and Modifier were measured using semi-volatile organic analysis (SVOA) and high performance liquid chromatography (HPLC) to determine the amount of solvent carryover. For low-flow (0.27 gpm aqueous) conditions in stripping, SVOA measured the Isopar L post-contactor concentration to be 25 mg/L, HPLC measured 39 mg/L of Modifier. For moderate-flow (0.54 gpm aqueous) conditions, SVOA measured the Isopar L postcontactor to be ~69 mg/L, while the HPLC measured 56 mg/L for Modifier. For high-flow (0.8 gpm aqueous) conditions, SVOA measured the Isopar L post-contactor to be 39 mg/L. The post-coalescer (pre-decanter) measurements by SVOA for Isopar L were all less than the analysis detection limit of 10 mg/L. The HPLC measured 18, 22 and 20 mg/L Modifier for the low, medium, and high-low rates respectively. In extraction, the quantity of pre-coalescer Isopar L carryover measured by SVOA was ~280-410 mg/L at low flow (4 gpm aqueous), ~400-450 mg/L at moderate flow (8 gpm aqueous), and ~480 mg/L at high flow (12 gpm aqueous). The amount of post coalescer (pre-decanter) Isopar L carryover measured by SVOA was less than 45 mg/L for all flow rates. HPLC results for Modifier were 182, 217 and 22

  13. Phosphazene additives

    DOE Patents [OSTI]

    Harrup, Mason K; Rollins, Harry W

    2013-11-26

    An additive comprising a phosphazene compound that has at least two reactive functional groups and at least one capping functional group bonded to phosphorus atoms of the phosphazene compound. One of the at least two reactive functional groups is configured to react with cellulose and the other of the at least two reactive functional groups is configured to react with a resin, such as an amine resin of a polycarboxylic acid resin. The at least one capping functional group is selected from the group consisting of a short chain ether group, an alkoxy group, or an aryloxy group. Also disclosed are an additive-resin admixture, a method of treating a wood product, and a wood product.

  14. Potlining Additives

    SciTech Connect (OSTI)

    Rudolf Keller

    2004-08-10

    In this project, a concept to improve the performance of aluminum production cells by introducing potlining additives was examined and tested. Boron oxide was added to cathode blocks, and titanium was dissolved in the metal pool; this resulted in the formation of titanium diboride and caused the molten aluminum to wet the carbonaceous cathode surface. Such wetting reportedly leads to operational improvements and extended cell life. In addition, boron oxide suppresses cyanide formation. This final report presents and discusses the results of this project. Substantial economic benefits for the practical implementation of the technology are projected, especially for modern cells with graphitized blocks. For example, with an energy savings of about 5% and an increase in pot life from 1500 to 2500 days, a cost savings of $ 0.023 per pound of aluminum produced is projected for a 200 kA pot.

  15. additive manufacturing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    additive manufacturing - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management Programs Advanced

  16. ,"Alaska Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    LNG Storage Additions (MMcf)" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description"," Of Series","Frequency","Latest Data for" ,"Data 1","Alaska...

  17. ,"Maine Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    ,"Worksheet Name","Description"," Of Series","Frequency","Latest Data for" ,"Data 1","Maine Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015"...

  18. STEP Intern Job Description

    Broader source: Energy.gov [DOE]

    STEP Intern Job Description, from the Tool Kit Framework: Small Town University Energy Program (STEP).

  19. V5 AND V10 CONTACTOR TESTING WITH THE NEXT GENERATION (CSSX) SOLVENT FOR THE SAVANNAH RIVER SITE INTEGRATED SALT DISPOSITION PROCESS

    SciTech Connect (OSTI)

    Restivo, M.; Peters, T.; Pierce, R.; Fondeur, F.; Steeper, T.; Williams, M.; Giddings, B.; Hickman, B.; Fink, S.

    2012-01-17

    A solvent extraction system for removal of cesium (Cs) from alkaline solutions was developed utilizing a novel solvent invented at the Oak Ridge National Laboratory (ORNL). This solvent consists of a calix[4]arene-crown-6 extractant dissolved in an inert hydrocarbon matrix. A Modifier is added to the solvent to enhance the extraction power of the calixarene and to prevent the formation of a third phase. An additional additive, called a suppressor, is used to improve stripping performance. The process that deploys this solvent system is known as Caustic Side Solvent Extraction (CSSX). The solvent system has been deployed at the Savannah River Site (SRS) in the Modular CSSX Unit (MCU) since 2008. Subsequent development efforts by ORNL identified an improved solvent system that can raise the expected decontamination factor (DF) in MCU from {approx}200 to more than 40,000. The improved DF is attributed to an improved distribution ratio for cesium [D(Cs)] in extraction from {approx}15 to {approx}60, an increased solubility of the calixarene in the solvent from 0.007 M to >0.050 M, and use of boric acid (H{sub 3}BO{sub 3}) stripping that also yields improved D(Cs) values. Additionally, the changes incorporated into the Next Generation CSSX Solvent (NGS) are intended to reduce solvent entrainment by virtue of more favorable physical properties. The MCU and Salt Waste Processing Facility (SWPF) facilities are actively pursuing the changeover from the current CSSX solvent to the NGS solvent. To support this integration of the NGS into the MCU and SWPF facilities, the Savannah River Remediation (SRR)/ARP/MCU Life Extension Project requested that the Savannah River National Laboratory (SRNL) perform testing of the new solvent for the removal of Cs from the liquid salt waste stream. Additionally, SRNL was tasked with characterizing both strip (20-in long, 10 micron pore size) and extraction (40-in long, 20 micron pore size) coalescers. SRNL designed a pilot-scale experimental program to test the full size strip (V5) and extraction (V10) centrifugal contactors and the associated strip and extraction effluent coalescers to determine the hydraulic and mass transfer characteristics with the NGS. The test program evaluated the amount of organic carryover and the droplet size of the carryover phases using several analytical methods. Provisions were also made to enable an evaluation of coalescer performance. Stage efficiency and mass distribution ratios were determined using Cs mass transfer measurements. Using 20 millimolar (mM) extractant (instead of 50 mM), the nominal D(Cs) measured was 16.0-17.5. The data indicate that equilibrium is achieved rapidly and maintained throughout sampling. The data showed good stage efficiency for extraction (Tests 1A-1D), ranging from 98.2% for Test 1A to 90.5% for Test 1D. No statistically-significant differences were noted for operations at 12 gpm aqueous flow when compared with either 4 gpm or 8 gpm of aqueous flow. The stage efficiencies equal or exceed those previously measured using the baseline CSSX solvent system. The nominal target for scrub Cs distribution values are {approx}1.0-2.5. The first scrub test yielded an average scrub value of 1.21 and the second scrub test produced an average value of 0.78. Both values are considered acceptable. Stage efficiency was not calculated for the scrub tests. For stripping behavior, six tests were completed in a manner to represent the first strip stage. For three tests at the baseline flow ratios (O:A of 3.75:1) but at different total flow rates, the D(Cs) values were all similar at {approx}0.052. Similar behavior was observed for two tests performed at an O:A ratio of 7:1 instead of 3.75:1. The data for the baseline strip tests exhibited acceptable stage efficiency, ranging from 82.0% for low flow to 89-90% for medium and high flow. The difference in efficiency may be attributable to the low volume in the contactor housing at lower flow rates. The concentrations of Isopar L{reg_sign} and Modifier were measured using semi-volatile organic analysis (SVOA

  20. TWRS baseline system description

    SciTech Connect (OSTI)

    Lee, A.K.

    1995-03-28

    This document provides a description of the baseline system conceptualized for remediating the tank waste stored within the Hanford Site. Remediation of the tank waste will be performed by the Tank Waste Remediation System (TWRS). This baseline system description (BSD) document has been prepared to describe the current planning basis for the TWRS for accomplishing the tank waste remediation functions. The BSD document is not intended to prescribe firm program management strategies for implementing the TWRS. The scope of the TWRS Program includes managing existing facilities, developing technology for new systems; building, testing and operating new facilities; and maintaining the system. The TWRS Program will manage the system used for receiving, safely storing, maintaining, treating, and disposing onsite, or packaging for offsite disposal, all tank waste. The scope of the TWRS Program encompasses existing facilities such as waste storage tanks, evaporators, pipelines, and low-level radioactive waste treatment and disposal facilities. It includes support facilities that comprise the total TWRS infrastructure, including upgrades to existing facilities or equipment and the addition of new facilities.

  1. Research Project Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    No job description found Current Research Opportunities Water Quality Standards and Feasibility Studies National Permit Discharge Elimination System Permitting Physiologically...

  2. YUCCA MOUNTAIN SITE DESCRIPTION

    SciTech Connect (OSTI)

    A.M. Simmons

    2004-04-16

    The ''Yucca Mountain Site Description'' summarizes, in a single document, the current state of knowledge and understanding of the natural system at Yucca Mountain. It describes the geology; geochemistry; past, present, and projected future climate; regional hydrologic system; and flow and transport within the unsaturated and saturated zones at the site. In addition, it discusses factors affecting radionuclide transport, the effect of thermal loading on the natural system, and tectonic hazards. The ''Yucca Mountain Site Description'' is broad in nature. It summarizes investigations carried out as part of the Yucca Mountain Project since 1988, but it also includes work done at the site in earlier years, as well as studies performed by others. The document has been prepared under the Office of Civilian Radioactive Waste Management quality assurance program for the Yucca Mountain Project. Yucca Mountain is located in Nye County in southern Nevada. The site lies in the north-central part of the Basin and Range physiographic province, within the northernmost subprovince commonly referred to as the Great Basin. The basin and range physiography reflects the extensional tectonic regime that has affected the region during the middle and late Cenozoic Era. Yucca Mountain was initially selected for characterization, in part, because of its thick unsaturated zone, its arid to semiarid climate, and the existence of a rock type that would support excavation of stable openings. In 1987, the United States Congress directed that Yucca Mountain be the only site characterized to evaluate its suitability for development of a geologic repository for high-level radioactive waste and spent nuclear fuel.

  3. HAZWOPER Training Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    55 Revision 0 Hanford Standardized HAZWOPER Training Program Description Prepared for the U.S. Department of Energy Assistant Secretary for Environmental Management Approved for Public Release; Further Dissemination Unlimited Hanford Standardized HAZWOPER Training Program Description, DOE-0355 Page 2 of 12 Senior Management Team Approval Hanford Standardized HAZWOPER Training Program Description, DOE-0355 Page 3 of 12 Hanford Training Manager Approval Hanford Standardized HAZWOPER Training

  4. ARM - Detailed Experiment Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Data Sets Weather Summary (pdf, 6M) New York Workshop Presentations Experiment Planning TWP-ICE Proposal Abstract Detailed Experiment Description Science Plan (pdf, 1M)...

  5. Chemical Sciences Project Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    & Simulation for the Chemical Sciences Project Description Almos every scientific activity at Los Alamos involves data analysis and modeling. From a chemical sciences point of ...

  6. VISION Model: Description

    SciTech Connect (OSTI)

    2009-01-18

    Description of VISION model, which is used to estimate the impact of highway vehicle technologies and fuels on energy use and carbon emissions to 2050.

  7. Detailed Income Statement Descriptions

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Program Description Sales Sales under the Transmission Rate Schedules Miscellaneous Revenue Sales that are not subject to Transmission rates schedules Inter-Business Unit...

  8. Original Workshop Proposal and Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Notes for Vis Requirements Original Workshop Proposal and Description Original Workshop Proposal and Description Visualization Requirements for Computational Science and ...

  9. B Plant facility description

    SciTech Connect (OSTI)

    Chalk, S.E.

    1996-10-04

    Buildings 225B, 272B, 282B, 282BA, and 294B were removed from the B Plant facility description. Minor corrections were made for tank sizes and hazardous and toxic inventories.

  10. ,"South Dakota Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    LNG Storage Additions (MMcf)" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description"," Of Series","Frequency","Latest Data for" ,"Data 1","South Dakota...

  11. BIA Description | Open Energy Information

    Open Energy Info (EERE)

    Description Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: BIA Description Abstract Description of Bureau of Indian Affairs. Author Bureau of Indian...

  12. Description of GPRA08 scenarios

    SciTech Connect (OSTI)

    None, None

    2009-01-18

    Background information for the FY 2007 GPRA methodology review providing a description of GPRA08 scenarios.

  13. SNF AGING SYSTEM DESCRIPTION DOCUMENT

    SciTech Connect (OSTI)

    L.L. Swanson

    2005-04-06

    The purpose of this system description document (SDD) is to establish requirements that drive the design of the spent nuclear fuel (SNF) aging system and associated bases, which will allow the design effort to proceed. This SDD will be revised at strategic points as the design matures. This SDD identifies the requirements and describes the system design, as it currently exists, with emphasis on attributes of the design provided to meet the requirements. This SDD is an engineering tool for design control; accordingly, the primary audience and users are design engineers. This SDD is part of an iterative design process. It leads the design process with regard to the flow down of upper tier requirements onto the system. Knowledge of these requirements is essential in performing the design process. The SDD follows the design with regard to the description of the system. The description provided in the SDD reflects the current results of the design process. Throughout this SDD, the term aging cask applies to vertical site-specific casks and to horizontal aging modules. The term overpack is a vertical site-specific cask that contains a dual-purpose canister (DPC) or a disposable canister. Functional and operational requirements applicable to this system were obtained from ''Project Functional and Operational Requirements'' (F&OR) (Curry 2004 [DIRS 170557]). Other requirements that support the design process were taken from documents such as ''Project Design Criteria Document'' (PDC) (BSC 2004 [DES 171599]), ''Site Fire Hazards Analyses'' (BSC 2005 [DIRS 172174]), and ''Nuclear Safety Design Bases for License Application'' (BSC 2005 [DIRS 171512]). The documents address requirements in the ''Project Requirements Document'' (PRD) (Canori and Leitner 2003 [DIRS 166275]). This SDD includes several appendices. Appendix A is a Glossary; Appendix B is a list of key system charts, diagrams, drawings, lists and additional supporting information; and Appendix C is a list of procedures that will be used to operate the system.

  14. Description of Proposed Action

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    RECORD OF CATEGORICAL EXCLUSION DETERMINATION 1 Description of Proposed Action Performance of a three-dimensional seismic survey line on approximately 2,409 acres contained within the WIPP Land Withdrawal Area as part of a larger survey to determine whether hydrocarbons are present in the region in quantities that warrant extraction and development. Number and Title of Applicable Categorical Exclusion B3.1 Site Characterization/Environmental Monitoring Activities covered by this Categorical

  15. Management control system description

    SciTech Connect (OSTI)

    Bence, P. J.

    1990-10-01

    This Management Control System (MCS) description describes the processes used to manage the cost and schedule of work performed by Westinghouse Hanford Company (Westinghouse Hanford) for the US Department of Energy, Richland Operations Office (DOE-RL), Richland, Washington. Westinghouse Hanford will maintain and use formal cost and schedule management control systems, as presented in this document, in performing work for the DOE-RL. This MCS description is a controlled document and will be modified or updated as required. This document must be approved by the DOE-RL; thereafter, any significant change will require DOE-RL concurrence. Westinghouse Hanford is the DOE-RL operations and engineering contractor at the Hanford Site. Activities associated with this contract (DE-AC06-87RL10930) include operating existing plant facilities, managing defined projects and programs, and planning future enhancements. This document is designed to comply with Section I-13 of the contract by providing a description of Westinghouse Hanford's cost and schedule control systems used in managing the above activities. 5 refs., 22 figs., 1 tab.

  16. Advanced Qualification of Additive Manufacturing Materials Workshop

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    July » Advanced Qualification of Additive Manufacturing Materials Workshop Advanced Qualification of Additive Manufacturing Materials Workshop WHEN: Jul 20, 2015 8:30 AM - Jul 21, 2015 7:30 PM WHERE: La Fonda on the Plaza Santa Fe, New Mexico SPEAKER: Multiple speakers CONTACT: Caryll Blount (505) 665-3950 CATEGORY: Science TYPE: Workshop INTERNAL: Calendar Login Event Description Invited speakers from universities and research centers, both US-based and Europe-based, will provide updates on

  17. Additive Manufacturing: Going Mainstream

    Broader source: Energy.gov [DOE]

    Additive manufacturing, or 3D printing, is receiving attention from media, investment communities and governments around the world transforming it from obscurity to something to be talked about.

  18. Program Description | Robotics Internship Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    March 4, 2016. Apply Now for the Robotics Internship About the Internship Program Description Start of Appointment Renewal of Appointment End of Appointment Stipend Information...

  19. ForTrilinos v 10.1

    Energy Science and Technology Software Center (OSTI)

    2010-03-24

    ForTrilinos stands for interfaces to Trilinos. It effectively replaces common practices for interfacing Fortran codes with Trilinos C++ packages. Common practices include writing user-specific drivers and exploiting the name-mangling schemes of specific compilers. ForTrilinos improves portability and robustness by exploiting the C interoperability constructs of Fortran 2003. These constructs facilitate binding Fortran interface bodies to their equivalent C function prototypes, providing for name resolution independent of the compiler™s underlying mangling scheme and guaranteeing compatible typemore » bit representations. Furthermore, ForTrilinos maintains the overall design philosophy and architecture of Trilinos by creating a derived type structure in Fortran similar to the class hierarchy in the underlying C++.ForTrilinos can be applied wherever the underlying Trilinos packages can be applied.« less

  20. Additive Manufacturing Technology Assessment

    Energy Savers [EERE]

    of Energy Additive Manufacturing Meets the Critical Materials Shortage Additive Manufacturing Meets the Critical Materials Shortage April 9, 2014 - 11:15am Addthis Green light reflection from a low-oxygen environment, 3D-printer laser deposition of metal powder alloys. | Photo courtesy of Critical Materials Institute, Ames Laboratory Green light reflection from a low-oxygen environment, 3D-printer laser deposition of metal powder alloys. | Photo courtesy of Critical Materials Institute, Ames

  1. DOE-RL Integrated Safety Management System Description

    SciTech Connect (OSTI)

    SHOOP, D.S.

    2000-09-01

    The purpose of this Integrated Safety Management System Description (ISMSD) is to describe the U.S. Department of Energy (DOE), Richland Operations Office (RL) ISMS as implemented through the RL Integrated Management System (RIMS). This ISMSD does not impose additional requirements but rather provides an overview describing how various parts of the ISMS fit together. Specific requirements for each of the core functions and guiding principles are established in other implementing processes, procedures, and program descriptions that comprise RIMS. RL is organized to conduct work through operating contracts; therefore, it is extremely difficult to provide an adequate ISMS description that only addresses RL functions. Of necessity, this ISMSD contains some information on contractor processes and procedures which then require RL approval or oversight. This ISMSD does not purport to contain a full description of the contractors' ISM System Descriptions.

  2. Unified Description of Nambu-Goldstone Bosons without Lorentz Invariance

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect Unified Description of Nambu-Goldstone Bosons without Lorentz Invariance Citation Details In-Document Search Title: Unified Description of Nambu-Goldstone Bosons without Lorentz Invariance Authors: Watanabe, Haruki ; Murayama, Hitoshi Publication Date: 2012-06-21 OSTI Identifier: 1103630 Type: Publisher's Accepted Manuscript Journal Name: Physical Review Letters Additional Journal Information: Journal Volume: 108; Journal Issue: 25; Journal ID: ISSN

  3. Detailed Course Module Description | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Detailed Course Module Description Detailed Course Module Description This document lists the course modules for building science courses offered at Cornell's Collaborator...

  4. CANISTER HANDLING FACILITY DESCRIPTION DOCUMENT

    SciTech Connect (OSTI)

    J.F. Beesley

    2005-04-21

    The purpose of this facility description document (FDD) is to establish requirements and associated bases that drive the design of the Canister Handling Facility (CHF), which will allow the design effort to proceed to license application. This FDD will be revised at strategic points as the design matures. This FDD identifies the requirements and describes the facility design, as it currently exists, with emphasis on attributes of the design provided to meet the requirements. This FDD is an engineering tool for design control; accordingly, the primary audience and users are design engineers. This FDD is part of an iterative design process. It leads the design process with regard to the flowdown of upper tier requirements onto the facility. Knowledge of these requirements is essential in performing the design process. The FDD follows the design with regard to the description of the facility. The description provided in this FDD reflects the current results of the design process.

  5. Packaging and Transportation of Additional Neptunium Oxide

    SciTech Connect (OSTI)

    Watkins, R.; Jordan, J.; Hensel, S.

    2010-05-05

    The Savannah River Site's HB-Line Facility completed a second neptunium oxide production campaign in which nine (9) additional cans of neptunium oxide were produced and shipped to the Idaho National Laboratory and Oak Ridge National Laboratory in the 9975 shipping container. These additional cans were from a different feed solution than the first fifty (50) cans of neptunium oxide that were previously produced and shipped via a Letter of Amendment to the 9975 Safety Analysis Report for Packaging (SARP) content table. This paper will address the challenges associated with demonstrating the neptunium oxide produced from the additional feed solution was equivalent to the original neptunium oxide and within the content description of the Letter of Amendment.

  6. Original Workshop Proposal and Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Notes for Vis Requirements » Original Workshop Proposal and Description Original Workshop Proposal and Description Visualization Requirements for Computational Science and Engineering Applications Proposal for a DoE Workshop to Be Held 
at the Berkeley Marina Radisson Hotel,
Berkeley, California, June 5, 2002
(date and location are tenative) Workshop Co-organizers: Bernd Hamann 
University of California-Davis Lawrence Berkeley Nat'l Lab. E. Wes Bethel 
Lawrence Berkeley Nat'l Lab.

  7. Quality Assurance Requirements and Description

    Energy Savers [EERE]

    QjCivilianRadioactive Was'fe Management QA: QA QVALITY ASSURANCE REQUIREMENTS AND DESCRIPTION DOEIRW-0333P Revisiol1 20 Effective Date: 10-01-2008 LarrY Newman, DlrectQr Office of Quality As,surance ~~--~-_._._- Edward F. Spr at III, Di or Office of Civilian Radioactive Waste Management Date I/Jf/4t' , . - - - Date OCRWM Title: Quality Assurance Requirements and Description DOEIRW-0333P, Revision 20 Office of Civilian Radioactive Waste Management Quality Assurance Policy Page: 2 of 160

  8. Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    & Evaluation Josh Warner, Manager Contract Administration Mike Rose, Manager Smart GridDemand Response Lee Hall, Manager Programs Brent Barclay, Manager IndustrialAg Sector...

  9. Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    challenging training environment Modeled after real-world events and scenarios Forces teams to push the boundaries of their comfort level with their tools and...

  10. Visiting Faculty Program Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Visiting Faculty Program Program Description The Visiting Faculty Program seeks to increase the research competitiveness of faculty members and their students at institutions historically underrepresented in the research community in order to expand the workforce vital to Department of Energy mission areas. As part of the program, selected university/college faculty members collaborate with DOE laboratory research staff on a research project of mutual interest. Program Objective The program is

  11. PURPOSE FORM INSTRUCTIONS Item Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    PURPOSE FORM INSTRUCTIONS Item Description 1 Enter inclusive dates of current reporting period. 2 Enter the official contract title. 3 Enter the official contract number. 4 Enter the name and address of each subcontractor. Subcontractors are to be grouped by state. 5 Enter ZIP code plus the 4-digit ZIP code extension. 6 Enter the subcontractor's business type (i.e. Academia, Industry, National Lab, Non-Profit Organization, State, or Other). 7 Enter the subcontractor's business classification

  12. Nuclear Industry Job Descriptions Boilermaker

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Incident Team NNSA houses the Nuclear Incident Team (NIT), which is responsible for deploying assets at the request of coordinating agencies in response to a nuclear or radiological incident. The NIT's mission is to coordinate NNSA assets for deployment, continually monitor deployment activities, and provide situational awareness of activities to NNSA management. The NIT is staffed and fully operational within two hours of notification

    Industry Job Descriptions Boilermaker Skilled craft who

  13. Student Internship Programs Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Student Internship Programs Program Description The objective of the Laboratory's student internship programs is to provide students with opportunities for meaningful hands- on experience supporting educational progress in their selected scientific or professional fields. The most significant impact of these internship experiences is observed in the intellectual growth experienced by the participants. Student interns are able to appreciate the practical value of their education efforts in their

  14. ELECTRICAL SUPPORT SYSTEM DESCRIPTION DOCUMENT

    SciTech Connect (OSTI)

    S. Roy

    2004-06-24

    The purpose of this revision of the System Design Description (SDD) is to establish requirements that drive the design of the electrical support system and their bases to allow the design effort to proceed to License Application. This SDD is a living document that will be revised at strategic points as the design matures over time. This SDD identifies the requirements and describes the system design as they exist at this time, with emphasis on those attributes of the design provided to meet the requirements. This SDD has been developed to be an engineering tool for design control. Accordingly, the primary audience/users are design engineers. This type of SDD both ''leads'' and ''trails'' the design process. It leads the design process with regard to the flow down of upper tier requirements onto the system. Knowledge of these requirements is essential in performing the design process. The SDD trails the design with regard to the description of the system. The description provided in the SDD is a reflection of the results of the design process to date. Functional and operational requirements applicable to electrical support systems are obtained from the ''Project Functional and Operational Requirements'' (F&OR) (Siddoway 2003). Other requirements to support the design process have been taken from higher-level requirements documents such as the ''Project Design Criteria Document'' (PDC) (Doraswamy 2004), and fire hazards analyses. The above-mentioned low-level documents address ''Project Requirements Document'' (PRD) (Canon and Leitner 2003) requirements. This SDD contains several appendices that include supporting information. Appendix B lists key system charts, diagrams, drawings, and lists, and Appendix C includes a list of system procedures.

  15. Zinc electrode with cement additive

    DOE Patents [OSTI]

    Charkey, Allen

    1982-06-01

    A zinc electrode having a cement additive, preferably, Portland Cement, distributed in the zinc active material.

  16. Descriptive Model of Generic WAMS

    SciTech Connect (OSTI)

    Hauer, John F.; DeSteese, John G.

    2007-06-01

    The Department of Energys (DOE) Transmission Reliability Program is supporting the research, deployment, and demonstration of various wide area measurement system (WAMS) technologies to enhance the reliability of the Nations electrical power grid. Pacific Northwest National Laboratory (PNNL) was tasked by the DOE National SCADA Test Bed Program to conduct a study of WAMS security. This report represents achievement of the milestone to develop a generic WAMS model description that will provide a basis for the security analysis planned in the next phase of this study.

  17. DOE-RL Integrated Safety Management System Program Description

    SciTech Connect (OSTI)

    SHOOP, D.S.

    2000-06-29

    The purpose of this Integrated Safety Management System (ISMS) Program Description (PD) is to describe the U.S. Department of Energy (DOE), Richland Operations Office (RL) ISMS as implemented through the RL Integrated Management System (RIMS). This PD does not impose additional requirements but rather provides an overview describing how various parts of the ISMS fit together. Specific requirements for each of the core functions and guiding principles are established in other implementing processes, procedures, and program descriptions that comprise RIMS. RL is organized to conduct work through operating contracts; therefore, it is extremely difficult to provide an adequate ISMS description that only addresses RL functions. Of necessity, this PD contains some information on contractor processes and procedures which then require RL approval or oversight.

  18. Additive Manufacturing for Fuel Cells

    Broader source: Energy.gov [DOE]

    Blake Marshall, AMO's lead for Additive Manufacturing Technologies, will provide an overview of current R&D activities in additive manufacturing and its application to fuel cell prototyping and...

  19. Biomass 2014 Additional Speaker Biographies

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Additional Speaker Biographies 1 | P a g e Contents David Danielson ............................................................................................................................................ 2 Kate Brandt ................................................................................................................................................... 3 Jennifer Holmgren

  20. Lubrication with boric acid additives

    DOE Patents [OSTI]

    Erdemir, Ali

    2000-01-01

    Self-lubricating resin compositions including a boric acid additive and a synthetic polymer including those thermoset materials.

  1. Incorporation of additives into polymers

    DOE Patents [OSTI]

    McCleskey, T. Mark; Yates, Matthew Z.

    2003-07-29

    There has been invented a method for incorporating additives into polymers comprising: (a) forming an aqueous or alcohol-based colloidal system of the polymer; (b) emulsifying the colloidal system with a compressed fluid; and (c) contacting the colloidal polymer with the additive in the presence of the compressed fluid. The colloidal polymer can be contacted with the additive by having the additive in the compressed fluid used for emulsification or by adding the additive to the colloidal system before or after emulsification with the compressed fluid. The invention process can be carried out either as a batch process or as a continuous on-line process.

  2. Microsoft Word - 338M_Geothermal_Project_Descriptions | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    338MGeothermalProjectDescriptions Microsoft Word - 338MGeothermalProjectDescriptions PDF icon Microsoft Word - 338MGeothermalProjectDescriptions More Documents & ...

  3. LANL installs additional protective measures

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Lab completes additional protections LANL installs additional protective measures Work crews completed additional flood and erosion-control measures this week to reduce the environmental effects of any flash floods following the Las Conchas Fire. July 20, 2011 Los Alamos National Laboratory sits on top of a once-remote mesa in northern New Mexico with the Jemez mountains as a backdrop to research and innovation covering multi-disciplines from bioscience, sustainable energy sources, to plasma

  4. Additional Resources | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Additional Resources Additional Resources Additional Resources Energy Assurance Planning The Local Government Energy Assurance Planning (LEAP) program, developed by the Public Technology Institute and the U.S. Department of Energy, offers resources to help local governments of all sizes in developing energy assurance plans for their communities. U.S. Department of Energy, State and Local Energy Assurance Planning The National Association of State Energy Officials (NASEO) The National Association

  5. Description of induced nuclear fission with Skyrme energy functionals. II.

    Office of Scientific and Technical Information (OSTI)

    Finite temperature effects (Journal Article) | SciTech Connect functionals. II. Finite temperature effects Citation Details In-Document Search Title: Description of induced nuclear fission with Skyrme energy functionals. II. Finite temperature effects Authors: Schunck, N. ; Duke, D. ; Carr, H. Publication Date: 2015-03-25 OSTI Identifier: 1180645 Grant/Contract Number: AC52-07NA27344 Type: Publisher's Accepted Manuscript Journal Name: Physical Review C Additional Journal Information: Journal

  6. ASP Program Description | Department of Energy

    Energy Savers [EERE]

    ASP Program Description ASP Program Description This program description provides an overview of the Analytical Services Program (ASP) activities for the United States (U.S.) Department of Energy (DOE or Department), including the National Nuclear Security Administration (NNSA). The Office of Environment, Health, Safety and Security (AU), Office of Sustainable Environmental Stewardship, manages the ASP, which is composed three elements: U.S. Department of Energy Consolidated Audit Program, Mixed

  7. Postdoctoral Program Program Description The Postdoctoral (Postdoc...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Postdoctoral Program Program Description The Postdoctoral (Postdoc) Research program offers the opportunity for appointees to perform research in a robust scientific R&D...

  8. Investigation and Analytical Description of Acoustic Production...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: Investigation and Analytical Description of Acoustic Production by Magneto-Acoustic Mixing Technology Citation Details In-Document Search This content will become...

  9. Slice Product Description (contracts/slice)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    meeting on March 4, 1999, to discuss the Slice Product Description and to receive oral comments. This report summarizes the issues raised in written and oral comments...

  10. MediaWiki:Mainpage-description | Open Energy Information

    Open Energy Info (EERE)

    Mainpage-description Jump to: navigation, search Main page Retrieved from "http:en.openei.orgwikiMediaWiki:Mainpage-description...

  11. Fight over fuel additive rekindled

    SciTech Connect (OSTI)

    Stringer, J.

    1996-03-20

    Ethyl and EPA are trading punches over EPA`s doubts about the safety of Ethyl`s gasoline additive methylcyclopentadienyl manganese (MMT). Late last week, EPA released a statement reaffirming its position that there has not been enough research on health effects of MMT and asking gas stations to label pumps that contain the additive so consumers will be aware they are using it. Responding to that statement, Ethyl has written Administrator Carol Browner asking why she appears to be supporting the Environmental Defense Fund`s (EDF; Washington) campaign against MMT and advocating the delay of the additive use in light of its known emission-reducing characteristics. The tension began in the early `90s, when the EPA refused to allow Ethyl to market MMT and required it to perform more long-term health studies. Last October a court ordered the agency to grant Ethyl approval to use MMT in nonreformulated gasoline.

  12. Out of bounds additive manufacturing

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Holshouser, Chris; Newell, Clint; Palas, Sid; Love, Lonnie J.; Kunc, Vlastimil; Lind, Randall F.; Lloyd, Peter D.; Rowe, John C.; Blue, Craig A.; Duty, Chad E.; et al

    2013-03-01

    Lockheed Martin and Oak Ridge National Laboratory are working on an additive manufacturing system capable of manufacturing components measured not in terms of inches or feet, but multiple yards in all dimensions with the potential to manufacture parts that are completely unbounded in size.

  13. Out of Bounds Additive Manufacturing

    SciTech Connect (OSTI)

    Holshouser, Chris [Lockheed Martin Corporation; Newell, Clint [Lockheed Martin Corporation; Palas, Sid [Lockheed Martin Corporation; Love, Lonnie J [ORNL; Kunc, Vlastimil [ORNL; Lind, Randall F [ORNL; Lloyd, Peter D [ORNL; Rowe, John C [ORNL; Blue, Craig A [ORNL; Duty, Chad E [ORNL; Peter, William H [ORNL; Dehoff, Ryan R [ORNL

    2013-01-01

    Lockheed Martin and Oak Ridge National Laboratory are working on an additive manufacturing (AM) system capable of manufacturing components measured not in terms of inches or feet, but multiple yards in all dimensions with the potential to manufacture parts that are completely unbounded in size.

  14. Decontamination formulation with sorbent additive

    SciTech Connect (OSTI)

    Tucker; Mark D. , Comstock; Robert H.

    2007-10-16

    A decontamination formulation and method of making that neutralizes the adverse health effects of both chemical and biological compounds, especially chemical warfare (CW) and biological warfare (BW) agents, and toxic industrial chemicals. The formulation provides solubilizing compounds that serve to effectively render the chemical and biological compounds, particularly CW and BW compounds, susceptible to attack, and at least one reactive compound that serves to attack (and detoxify or kill) the compound. The formulation includes at least one solubilizing agent, a reactive compound, a bleaching activator, a sorbent additive, and water. The highly adsorbent, water-soluble sorbent additive (e.g., sorbitol or mannitol) is used to "dry out" one or more liquid ingredients, such as the liquid bleaching activator (e.g., propylene glycol diacetate or glycerol diacetate) and convert the activator into a dry, free-flowing powder that has an extended shelf life, and is more convenient to handle and mix in the field.

  15. Additive Manufacturing: Technology and Applications

    Energy Savers [EERE]

    Lower energy intensity: These techniques save energy by eliminating production steps, using substantially less material, enabling reuse of by-products, and producing lighter products. Remanufacturing parts through advanced additive manufacturing and surface treatment processes can also return end-of-life products to as-new condition, 1 using only 2-25% of the energy required to make new parts. 2 * Less waste: Building objects up layer by layer, instead of traditional machining processes that

  16. CHP R&D Project Descriptions

    Broader source: Energy.gov [DOE]

    The CHP R&D project portfolio includes advanced reciprocating engine systems (ARES), packaged CHP systems, high-value applications, fuel-flexible CHP, and demonstrations of these technologies. Project fact sheets and short project descriptions are provided below:

  17. Date Time Event Description/Participants Location

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Updated: 06112015 Date Time Event DescriptionParticipants Location Point of Contact 11 thru 12 All Day Meeting Todd Allen, deputy director of Science and Technology at INL, has...

  18. Description of Energy Intensity Tables (12)

    U.S. Energy Information Administration (EIA) Indexed Site

    3. Description of Energy Intensity Data Tables There are 12 data tables used as references for this report. Specifically, these tables are categorized as tables 1 and 2 present...

  19. Additive manufacturing of hybrid circuits

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Bell, Nelson S.; Sarobol, Pylin; Cook, Adam; Clem, Paul G.; Keicher, David M.; Hirschfeld, Deidre; Hall, Aaron Christopher

    2016-03-26

    There is a rising interest in developing functional electronics using additively manufactured components. Considerations in materials selection and pathways to forming hybrid circuits and devices must demonstrate useful electronic function; must enable integration; and must complement the complex shape, low cost, high volume, and high functionality of structural but generally electronically passive additively manufactured components. This article reviews several emerging technologies being used in industry and research/development to provide integration advantages of fabricating multilayer hybrid circuits or devices. First, we review a maskless, noncontact, direct write (DW) technology that excels in the deposition of metallic colloid inks for electrical interconnects.more » Second, we review a complementary technology, aerosol deposition (AD), which excels in the deposition of metallic and ceramic powder as consolidated, thick conformal coatings and is additionally patternable through masking. As a result, we show examples of hybrid circuits/devices integrated beyond 2-D planes, using combinations of DW or AD processes and conventional, established processes.« less

  20. NDMAS System and Process Description (Technical Report) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Technical Report: NDMAS System and Process Description Citation Details In-Document Search Title: NDMAS System and Process Description × You are accessing a document from the Department of Energy's (DOE) SciTech Connect. This site is a product of DOE's Office of Scientific and Technical Information (OSTI) and is provided as a public service. Visit OSTI to utilize additional information resources in energy science and technology. A paper copy of this document is also available for sale to the

  1. Detailed Course Module Description | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Detailed Course Module Description Detailed Course Module Description This document lists the course modules for building science courses offered at Cornell's Collaborator Sustainable Buildingi Practice course. PDF icon course_module.pdf More Documents & Publications Building America Building Science Education Roadmap Building America Program Research-to-Market Plan Opportunities for Building America Research to Address Energy Upgrade Technical Challenges: HVAC, Envelope and IAQ (301)

  2. Microsoft Word - HQ ISM System Description Final

    National Nuclear Security Administration (NNSA)

    NA-1 SD 450.4-1 Approved: 10-23-07 National Nuclear Security Administration Headquarters Integrated Safety Management System Description This NNSA Headquarters Integrated Safety Management System Description describes the NNSA Headquarters role in establishing expectations and accomplishing work in a safe and environmentally sound manner to successfully execute the NNSA mission and strategic goals. NNSA senior managers strongly support and are personally committed to implementation of the policy

  3. Course Descriptions - Combustion Energy Frontier Research Center

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Lecture Videos News, Events & Publications Contact CEFRC CEFRC In Pictures CEFRC Intranet (Members Only) Home » 2016 Combustion Summer School » Course Descriptions Course Descriptions Combustion Dynamics Lecturer: Prof. Sébastien M. Candel, École Centrale Paris Course Length: 15 hours (Mon - Fri) Session: Morning Session Objective: This course provides an introduction to the analysis of combustion dynamics problems. It includes a tutorial on acoustics and on early combustion instability

  4. PROJECT W-551 INTERIM PRETREATMENT SYSTEM PRECONCEPTUAL CANDIDATE TECHNOLOGY DESCRIPTIONS

    SciTech Connect (OSTI)

    MAY TH

    2008-08-12

    The Office of River Protection (ORP) has authorized a study to recommend and select options for interim pretreatment of tank waste and support Waste Treatment Plant (WTP) low activity waste (LAW) operations prior to startup of all the WTP facilities. The Interim Pretreatment System (IPS) is to be a moderately sized system which separates entrained solids and 137Cs from tank waste for an interim time period while WTP high level waste vitrification and pretreatment facilities are completed. This study's objective is to prepare pre-conceptual technology descriptions that expand the technical detail for selected solid and cesium separation technologies. This revision includes information on additional feed tanks.

  5. Nuclear Waste Partnership (NWP) Quality Assurance Program Description...

    Office of Environmental Management (EM)

    Waste Partnership (NWP) Quality Assurance Program Description (QAPD) Nuclear Waste Partnership (NWP) Quality Assurance Program Description (QAPD) The documents included in this...

  6. CleanEnergyProjectsonTribalLands_Project_Descriptions_072011...

    Broader source: Energy.gov (indexed) [DOE]

    CleanEnergyProjectsonTribalLandsProjectDescriptions072011.pdf More Documents & Publications CleanEnergyProjectsonTribalLandsProjectDescriptions072011.pdf...

  7. Microsoft Word - 564M_Biomass_Project Descriptions FINAL 120409...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Microsoft Word - 564MBiomassProject Descriptions FINAL 120409 PDF icon Microsoft Word - 564MBiomassProject Descriptions FINAL 120409 More Documents & Publications ...

  8. Microscopic Description of Nuclear Fission: Fission Barrier Heights...

    Office of Scientific and Technical Information (OSTI)

    Microscopic Description of Nuclear Fission: Fission Barrier Heights of Even-Even Actinides Citation Details In-Document Search Title: Microscopic Description of Nuclear Fission: ...

  9. Unified Description of Nambu-Goldstone Bosons without Lorentz...

    Office of Scientific and Technical Information (OSTI)

    Unified Description of Nambu-Goldstone Bosons without Lorentz Invariance Citation Details In-Document Search Title: Unified Description of Nambu-Goldstone Bosons without Lorentz ...

  10. Description of induced nuclear fission with Skyrme energy functionals...

    Office of Scientific and Technical Information (OSTI)

    Description of induced nuclear fission with Skyrme energy functionals: Static potential ... Citation Details In-Document Search Title: Description of induced nuclear fission with ...

  11. Microscopic Description of Nuclear Fission: Fission Barrier Heights...

    Office of Scientific and Technical Information (OSTI)

    Conference: Microscopic Description of Nuclear Fission: Fission Barrier Heights of Even-Even Actinides Citation Details In-Document Search Title: Microscopic Description of Nuclear ...

  12. Description of Induced Nuclear Fission with Skyrme Energy Functionals...

    Office of Scientific and Technical Information (OSTI)

    Description of Induced Nuclear Fission with Skyrme Energy Functionals: II. Finite Temperature Effects Citation Details In-Document Search Title: Description of Induced Nuclear ...

  13. Integrated Program Management Report (IPMR) Data Item Description...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Integrated Program Management Report (IPMR) Data Item Description (DID) Integrated Program Management Report (IPMR) Data Item Description (DID) Integrated Program Management Report...

  14. SURFACE INDUSTRIAL HVAC SYSTEM DESCRIPTION DOCUMENT

    SciTech Connect (OSTI)

    M.M. Ansari

    2005-04-05

    The purpose of this system description document (SDD) is to establish requirements that drive the design of the surface industrial heating, ventilation, and air-conditioning (HVAC) system and its bases to allow the design effort to proceed to license application. This SDD will be revised at strategic points as the design matures. This SDD identifies the requirements and describes the system design, as it currently exists, with emphasis on attributes of the design provided to meet the requirements. This SDD is an engineering tool for design control; accordingly, the primary audience and users are design engineers. This SDD is part of an iterative design process. It leads the design process with regard to the flowdown of upper tier requirements onto the system. Knowledge of these requirements is essential to performing the design process. The SDD follows the design with regard to the description of the system. The description that provided in this SDD reflects the current results of the design process.

  15. Recommendation 212: Evaluate additional storage and disposal...

    Office of Environmental Management (EM)

    2: Evaluate additional storage and disposal options Recommendation 212: Evaluate additional storage and disposal options The ORSSAB encourages DOE to evaluate additional storage...

  16. Develop & evaluate materials & additives that enhance thermal...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Additives that Enhance Thermal and Overcharge Abuse Electrolytes - Advanced Electrolyte and Electrolyte Additives Advanced Electrolyte Additives for PHEVEV Lithium-ion Battery

  17. Paducah Site Description | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Background » Paducah Site Description Paducah Site Description The 3,556-acre Paducah Site is located in western Kentucky The 3,556-acre Paducah Site is located in western Kentucky Paducah state Map The Paducah Gaseous Diffusion (PGDP) Site is located in McCracken County, Kentucky, 10 miles west of the city of Paducah. The plant is located on a 3,556-acre DOE site, of which approximately 750 acres are within the fenced security area. The PGDP footprint has more than 500 facilities, 19 miles of

  18. Electrolytes - Advanced Electrolyte and Electrolyte Additives...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications Electrolytes - Advanced Electrolyte and Electrolyte Additives Develop & evaluate materials & additives that enhance thermal & overcharge abuse ...

  19. Electrolytes - Advanced Electrolyte and Electrolyte Additives...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications Development of Advanced Electrolytes and Electrolyte Additives Electrolytes - Advanced Electrolyte and Electrolyte Additives Develop & evaluate ...

  20. Electrolytes - Advanced Electrolyte and Electrolyte Additives...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications Electrolytes - Advanced Electrolyte and Electrolyte Additives Electrolytes - Advanced Electrolyte and Electrolyte Additives Develop & Evaluate ...

  1. Recommendation 223: Recommendations on Additional Waste Disposal...

    Office of Environmental Management (EM)

    3: Recommendations on Additional Waste Disposal Capacity Recommendation 223: Recommendations on Additional Waste Disposal Capacity ORSSAB's recommendations encourage DOE to...

  2. DOE-LPO-MiniReport_PV_v10

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy's Loan Programs O ce (LPO) was instrumental in launching the utility-scale photovoltaic (PV) solar industry in the United States. In 2009, there was not a single PV solar facility larger than 100 megawatts (MW) operating in the United States. Despite growing demand for this clean, renewable energy source, developers faced challenges securing the financing necessary to build these large projects. LPO stepped in to address this market barrier by providing more than $4.6

  3. DOE-LPO-MiniReport_PV_v10

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    in launching the utility-scale photovoltaic (PV) solar industry in the United States. ... February 2015 POWERING NEW MARKETS: UTILITY-SCALE PHOTOVOLTAIC SOLAR energy.govlpo 1 In ...

  4. TWRS information locator database system design description

    SciTech Connect (OSTI)

    Knutson, B.J.

    1996-09-13

    This document gives an overview and description of the Tank Waste Remediation System (TWRS) Information Locator Database (ILD)system design. The TWRS ILD system is an inventory of information used in the TWRS Systems Engineering process to represent the TWRS Technical Baseline. The inventory is maintained in the form of a relational database developed in Paradox 4.5.

  5. Network architecture functional description and design

    SciTech Connect (OSTI)

    Stans, L.; Bencoe, M.; Brown, D.; Kelly, S.; Pierson, L.; Schaldach, C.

    1989-05-25

    This report provides a top level functional description and design for the development and implementation of the central network to support the next generation of SNL, Albuquerque supercomputer in a UNIX{reg sign} environment. It describes the network functions and provides an architecture and topology.

  6. Better Buildings Neighborhood Program Business Models Guide: Program Administrator Description

    Broader source: Energy.gov [DOE]

    Better Buildings Neighborhood Program Business Models Guide: Program Administrator Business Models, Program Administrator Description.

  7. Alternative Fuels Data Center: Latest Additions

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    Publications » Latest Additions Printable Version Share this resource Send a link to Alternative Fuels Data Center: Latest Additions to someone by E-mail Share Alternative Fuels Data Center: Latest Additions on Facebook Tweet about Alternative Fuels Data Center: Latest Additions on Twitter Bookmark Alternative Fuels Data Center: Latest Additions on Google Bookmark Alternative Fuels Data Center: Latest Additions on Delicious Rank Alternative Fuels Data Center: Latest Additions on Digg Find More

  8. System Design Description PFP Thermal Stabilization

    SciTech Connect (OSTI)

    RISENMAY, H.R.

    2000-04-25

    The purpose of this document is to provide a system design description (SDD) and design basis for the Plutonium Finishing Plant (PFP) Thermal Stabilization project. The chief objective of the SDD is to document the Structures, Systems, and Components (SSCs) that establish and maintain the facility Safety Envelope necessary for normal safe operation of the facility; as identified in the FSAR, the OSRs, and Safety Assessment Documents (SADs). This safety equipment documentation should satisfy guidelines for the SDD given in WHC-SD-CP-TI-18 1, Criteria for Identification and Control of Equipment Necessary for Preservation of the Safety Envelope and Safe Operation of PFP. The basis for operational, alarm response, maintenance, and surveillance procedures are also identified and justified in this document. This document and its appendices address the following elements of the PFP Thermal Stabilization project: Functional and design requirements; Design description; Safety Envelope Analysis; Safety Equipment Class; and Operational, maintenance and surveillance procedures.

  9. Acquisition Description/ Category Solicitation Method Contract Type

    Energy Savers [EERE]

    13/2016 Acquisition Description/ Category Solicitation Method Contract Type Period of Performance Contract Value All EM Sites DOE-Wide commercial low-level waste treatment Energy Solutions, Inc. Perma-Fix Environmental Services, Inc. Philo-Technics, Ltd. Studsvik, Inc. Full and Open Competition Firm Fixed Price IDIQ 6/30/08-6/29/13 $450M Multiple award indefinite delivery/indefinite quality (IDIQ) Set-aside contracts for nationwide environmental services/ environmental cleanup Clauss

  10. Certificate in Environmental Monitoring Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Certificate in Environmental Monitoring Program Description Since a primary goal of the Neighborhood Environmental Watch Network (NEWNET) project is to provide information to the public, it is fitting that there are appropriate education programs. NEWNET has collaborated with several local high schools and colleges by providing them with local NEWNET stations. Some teaching curricula include a study of radiation and detection, data acquisition and plotting, meteorology, or uses of computers.

  11. Machinist Pipeline/Apprentice Program Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Machinist Pipeline/Apprentice Program Program Description The Machinist Pipeline Program was created by the Prototype Fabrication Division to fill a critical need for skilled journeyworker machinists. It is based on a program developed by the National Institute for Metalworking Skills (NIMS) in conjunction with metalworking trade associations to develop and maintain a globally competitive U.S. workforce. The goal is to develop and implement apprenticeship programs that are aligned with

  12. Development of Advanced Electrolytes and Electrolyte Additives...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Electrolytes and Electrolyte Additives Development of Advanced Electrolytes and Electrolyte Additives 2010 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and ...

  13. Develop & Evaluate Materials & Additives that Enhance Thermal...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Evaluate Materials & Additives that Enhance Thermal & Overcharge Abuse Develop & Evaluate Materials & Additives that Enhance Thermal & Overcharge Abuse 2011 DOE Hydrogen and Fuel ...

  14. Advanced Qualification of Additive Manufacturing Workshop

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Additive Manufacturing Workshop Poster Abstract Submission - deadline July 10, 2015 Advanced Qualification of Additive Manufacturing Materials using in situ sensors, diagnostics...

  15. Directives Requiring Additional Documentation - DOE Directives,

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Delegations, and Requirements Requiring Additional Documentation by Website Administrator PDF document icon DirectivesRequiringAdditionalDocumentation (1).pdf - PDF document, 35 KB (36219

  16. Additive Manufacturing: Pursuing the Promise | Department of...

    Broader source: Energy.gov (indexed) [DOE]

    Fact sheet overviewing additive manufacturing techniques that are projected to exert a profound impact on manufacturing. Additive Manufacturing: Pursuing the Promise More Documents...

  17. Advanced Qualification of Additive Manufacturing Materials Workshop

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Advanced Qualification of Additive Manufacturing Materials Workshop Advanced Qualification of Additive Manufacturing Materials Workshop WHEN: Jul 20, 2015 8:30 AM - Jul 21, 2015...

  18. Additional Guidance Regarding Application of Current Procedures...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Additional Guidance Regarding Application of Current Procedures for Testing Energy Consumption of Clothes Washers with Warm Rinse Cycles, Issued: June 30, 2010 Additional Guidance...

  19. Advances in the ab initio description of nuclear three-cluster systems

    Office of Scientific and Technical Information (OSTI)

    (Conference) | SciTech Connect Advances in the ab initio description of nuclear three-cluster systems Citation Details In-Document Search Title: Advances in the ab initio description of nuclear three-cluster systems × You are accessing a document from the Department of Energy's (DOE) SciTech Connect. This site is a product of DOE's Office of Scientific and Technical Information (OSTI) and is provided as a public service. Visit OSTI to utilize additional information resources in energy

  20. Hamiltonian description of the ideal fluid

    SciTech Connect (OSTI)

    Morrison, P.J.

    1994-01-01

    Fluid mechanics is examined from a Hamiltonian perspective. The Hamiltonian point of view provides a unifying framework; by understanding the Hamiltonian perspective, one knows in advance (within bounds) what answers to expect and what kinds of procedures can be performed. The material is organized into five lectures, on the following topics: rudiments of few-degree-of-freedom Hamiltonian systems illustrated by passive advection in two-dimensional fluids; functional differentiation, two action principles of mechanics, and the action principle and canonical Hamiltonian description of the ideal fluid; noncanonical Hamiltonian dynamics with examples; tutorial on Lie groups and algebras, reduction-realization, and Clebsch variables; and stability and Hamiltonian systems.

  1. Tribal Energy Program February 2012 Award Project Descriptions | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Tribal Energy Program February 2012 Award Project Descriptions Tribal Energy Program February 2012 Award Project Descriptions Project descriptions of the 19 tribal energy projects selected for negotiation of award. PDF icon Tribal Energy Program Feb 2012 Awards Project Descriptions_0.pdf More Documents & Publications Community-Scale Project Development and Finance Workshop Agenda and Presentations: New Mexico 2012 Program Review Meeting Project Reports for Pueblo of Zia - 2012

  2. STEP Energy Coach and Technical Consultant Job Descriptions

    Broader source: Energy.gov [DOE]

    STEP Energy Coach and Technical Consultant Job Descriptions, from the Tool Kit Framework: Small Town University Energy Program (STEP).

  3. COG Software Architecture Design Description Document

    SciTech Connect (OSTI)

    Buck, R M; Lent, E M

    2009-09-21

    This COG Software Architecture Design Description Document describes the organization and functionality of the COG Multiparticle Monte Carlo Transport Code for radiation shielding and criticality calculations, at a level of detail suitable for guiding a new code developer in the maintenance and enhancement of COG. The intended audience also includes managers and scientists and engineers who wish to have a general knowledge of how the code works. This Document is not intended for end-users. This document covers the software implemented in the standard COG Version 10, as released through RSICC and IAEA. Software resources provided by other institutions will not be covered. This document presents the routines grouped by modules and in the order of the three processing phases. Some routines are used in multiple phases. The routine description is presented once - the first time the routine is referenced. Since this is presented at the level of detail for guiding a new code developer, only the routines invoked by another routine that are significant for the processing phase that is being detailed are presented. An index to all routines detailed is included. Tables for the primary data structures are also presented.

  4. Active Sites Additional Information | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Active Sites Additional Information Active Sites Additional Information Active Sites Additional Information The Office of Environmental Management (EM) supports the Department's Strategic Plan to complete the environmental remediation of legacy and active sites, while protecting human health and the environment by completing environmental remediation of legacy and active Cold War sites. The EM program was established in 1989 and is responsible for the cleanup of millions of gallons of liquid

  5. Advanced Qualification of Additive Manufacturing Workshop

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Additive Manufacturing Workshop Advanced Qualification of Additive Manufacturing Materials (AM) Workshop Our goal is to define opportunities and research gaps within additive manufacturing (AM) and to engage the broader scientific/engineering community to discuss future research directions. thumbnail of thumbnail of Contact Institute Director Dr. Alexander V. Balatsky Institute for Materials Science (505) 665-0077 Email Deputy Director Dr. Jennifer S. Martinez Institute for Materials Science

  6. Cincinnati Big Area Additive Manufacturing (BAAM)

    SciTech Connect (OSTI)

    Duty, Chad E.; Love, Lonnie J.

    2015-03-04

    Oak Ridge National Laboratory (ORNL) worked with Cincinnati Incorporated (CI) to demonstrate Big Area Additive Manufacturing which increases the speed of the additive manufacturing (AM) process by over 1000X, increases the size of parts by over 10X and shows a cost reduction of over 100X. ORNL worked with CI to transition the Big Area Additive Manufacturing (BAAM) technology from a proof-of-principle (TRL 2-3) demonstration to a prototype product stage (TRL 7-8).

  7. Additive Manufacturing Meets the Critical Materials Shortage

    Broader source: Energy.gov [DOE]

    Find out how the Energy Department's Advanced Manufacturing Office is working to address potential shortages of critical materials through additive manufacturing, or 3D printing.

  8. ,"Maryland Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Maryland Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  9. ,"Nebraska Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Nebraska Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  10. ,"Wisconsin Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Wisconsin Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  11. ,"Connecticut Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Connecticut Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  12. ,"Idaho Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Idaho Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  13. ,"Tennessee Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Tennessee Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  14. ,"Pennsylvania Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Pennsylvania Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  15. ,"Nevada Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Nevada Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  16. ,"California Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","California Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  17. ,"Oregon Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Oregon Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  18. ,"Delaware Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Delaware Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  19. ,"Arkansas Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Arkansas Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  20. ,"Louisiana Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Louisiana Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  1. ,"Missouri Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Missouri Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  2. ,"Texas Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Texas Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  3. ,"Washington Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Washington Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  4. ,"Alabama Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Alabama Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  5. ,"Georgia Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Georgia Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  6. ,"Virginia Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Virginia Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  7. ,"Indiana Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Indiana Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  8. ,"Minnesota Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Minnesota Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  9. ,"Massachusetts Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Massachusetts Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  10. Surface Additives for Enhanced Electrode Performance - Energy...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ...efficient and almost non-polluting, making them an attractive alternative for energy generation. Some solid oxide fuel cells burn ... High performance additives then can be ...

  11. DOE Announces Additional Energy Efficiency Enforcement Action...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Counsel, Haier voluntarily identified a parts defect that had caused the freezer models to consume additional energy and took immediate steps on its own to remedy the defects. ...

  12. Redox Shuttle Additives | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    available for licensing: A series of novel redox shuttle additives for lithium-ion batteries Seven-technology suite helps reduce battery costs Provides overcharge...

  13. additive manufacturuing | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Laboratory engineer Bryan Moran won an award last month for his 3D printing innovation. It could revolutionize additive manufacturing.Lawrence Livermore Lab engineer Bryan Moran...

  14. AHTR Refueling Systems and Process Description

    SciTech Connect (OSTI)

    Varma, Venugopal Koikal; Holcomb, David Eugene; Bradley, Eric Craig; Zaharia, Nathaniel M; Cooper, Eliott J

    2012-07-01

    The Advanced High-Temperature Reactor (AHTR) is a design concept for a central station-type [1500 MW(e)] Fluoride salt-cooled High-temperature Reactor (FHR) that is currently undergoing development by Oak Ridge National Laboratory for the US. Department of Energy, Office of Nuclear Energy's Advanced Reactor Concepts program. FHRs, by definition, feature low-pressure liquid fluoride salt cooling, coated-particle fuel, a high-temperature power cycle, and fully passive decay heat rejection. The overall goal of the AHTR development program is to demonstrate the technical feasibility of FHRs as low-cost, large-size power producers while maintaining full passive safety. The AHTR is approaching a preconceptual level of maturity. An initial integrated layout of its major systems, structures, and components (SSCs), and an initial, high-level sequence of operations necessary for constructing and operating the plant is nearing completion. An overview of the current status of the AHTR concept has been recently published and a report providing a more detailed overview of the AHTR structures and mechanical systems is currently in preparation. This report documents the refueling components and processes envisioned at this early development phase. The report is limited to the refueling aspects of the AHTR and does not include overall reactor or power plant design information. The report, however, does include a description of the materials envisioned for the various components and the instrumentation necessary to control the refueling process. The report begins with an overview of the refueling strategy. Next a mechanical description of the AHTR fuel assemblies and core is provided. The reactor vessel upper assemblies are then described. Following this the refueling path structures and the refueling mechanisms and components are described. The sequence of operations necessary to fuel and defuel the reactor is then discussed. The report concludes with a discussion of the levels of maturity of the various SSCs to provide guidance for future technology developments. The conceptual design information presented in this report is very preliminary in nature. Significant uncertainty remains about several aspects of the process and even the radiation and mechanical performance of plate-type coated-particle fuel.

  15. AHTR Refueling Systems and Process Description

    SciTech Connect (OSTI)

    Varma, V.K.; Holcomb, D.E.; Bradley, E.C.; Zaharia, N.M.; Cooper, E.J.

    2012-07-15

    The Advanced High-Temperature Reactor (AHTR) is a design concept for a central station-type [1500 MW(e)] Fluoride salt–cooled High-temperature Reactor (FHR) that is currently undergoing development by Oak Ridge National Laboratory for the US. Department of Energy, Office of Nuclear Energy’s Advanced Reactor Concepts program. FHRs, by definition, feature low-pressure liquid fluoride salt cooling, coated-particle fuel, a high-temperature power cycle, and fully passive decay heat rejection. The overall goal of the AHTR development program is to demonstrate the technical feasibility of FHRs as low-cost, large-size power producers while maintaining full passive safety. The AHTR is approaching a preconceptual level of maturity. An initial integrated layout of its major systems, structures, and components (SSCs), and an initial, high-level sequence of operations necessary for constructing and operating the plant is nearing completion. An overview of the current status of the AHTR concept has been recently published [1], and a report providing a more detailed overview of the AHTR structures and mechanical systems is currently in preparation. This report documents the refueling components and processes envisioned at this early development phase. The report is limited to the refueling aspects of the AHTR and does not include overall reactor or power plant design information. The report, however, does include a description of the materials envisioned for the various components and the instrumentation necessary to control the refueling process. The report begins with an overview of the refueling strategy. Next a mechanical description of the AHTR fuel assemblies and core is provided. The reactor vessel upper assemblies are then described. Following this the refueling path structures and the refueling mechanisms and components are described. The sequence of operations necessary to fuel and defuel the reactor is then discussed. The report concludes with a discussion of the levels of maturity of the various SSCs to provide guidance for future technology developments. The conceptual design information presented in this report is very preliminary in nature. Significant uncertainty remains about several aspects of the process and even the radiation and mechanical performance of plate-type coated-particle fuel.

  16. additive manufacturing | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Home additive manufacturing LLNL researchers outline what happens during metal 3D printing, enhancing confidence From left, Lawrence Livermore National Laboratory researchers Ibo Matthews, a principal investigator leading the lab's effort on the joint open source software project; Wayne King, director of the Accelerated Certification of Additively Manufactured Metals Initiative; and Gabe Guss, engineering...

  17. Photoactive devices including porphyrinoids with coordinating additives

    DOE Patents [OSTI]

    Forrest, Stephen R; Zimmerman, Jeramy; Yu, Eric K; Thompson, Mark E; Trinh, Cong; Whited, Matthew; Diev, Vlacheslav

    2015-05-12

    Coordinating additives are included in porphyrinoid-based materials to promote intermolecular organization and improve one or more photoelectric characteristics of the materials. The coordinating additives are selected from fullerene compounds and organic compounds having free electron pairs. Combinations of different coordinating additives can be used to tailor the characteristic properties of such porphyrinoid-based materials, including porphyrin oligomers. Bidentate ligands are one type of coordinating additive that can form coordination bonds with a central metal ion of two different porphyrinoid compounds to promote porphyrinoid alignment and/or pi-stacking. The coordinating additives can shift the absorption spectrum of a photoactive material toward higher wavelengths, increase the external quantum efficiency of the material, or both.

  18. CHP R&D Project Descriptions | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    CHP R&D Project Descriptions CHP R&D Project Descriptions The CHP R&D project portfolio includes advanced reciprocating engine systems (ARES), packaged CHP systems, high-value applications, fuel-flexible CHP, and demonstrations of these technologies. Project fact sheets and short project descriptions are provided below: Advanced Reciprocating Engine Systems Advanced Reciprocating Engine Systems (ARES) The ARES program is designed to promote separate, but parallel engine development

  19. 2015 ASP Program Report Description | Department of Energy

    Energy Savers [EERE]

    ASP Program Report Description 2015 ASP Program Report Description This report provides an overview of the ASP's activities for Fiscal Year (FY) 2015 for the United States (U.S.) Department of Energy (DOE or Department), including the National Nuclear Security Administration (NNSA). The ASP is managed by the Office of Environment, Health, Safety and Security (AU), Office of Sustainable Environmental Stewardship. The ASP fiscal year reports supplement the ASP Program Description, March 2016,

  20. Integrated Program Management Report (IPMR) Data Item Description (DID) |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Integrated Program Management Report (IPMR) Data Item Description (DID) Integrated Program Management Report (IPMR) Data Item Description (DID) Integrated Program Management Report (IPMR) combines the Contractor Performance Report (CPR) and Integrated Master Schedule (IMS) reporting requirements on contracts requiring Earned Value Management (EVM) reporting of project/contract performance. Document available for download via link below provides Data Item Description

  1. Section I - FUNDING OPPORTUNITY DESCRIPTION | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Section I - FUNDING OPPORTUNITY DESCRIPTION More Documents & Publications U. S. Department of Energy - Headquarters Advanced Research Projects Agency Advanced Research Projects...

  2. Tank Monitor and Control System (TMACS) Version Description Document (VDD)

    SciTech Connect (OSTI)

    BARNES, D.A.

    2000-07-06

    This document updates the Version Description Document with the changes incorporated in the Revision 12.0 software installation on the Tank Monitor and Control System (TMACS).

  3. TITLE AUTHORS SUBJECT SUBJECT RELATED DESCRIPTION PUBLISHER AVAILABILI...

    Office of Scientific and Technical Information (OSTI)

    further description Trainor Guitton Hoversten Nordquist Intani Value of information analysis using geothermal field data accounting for multiple interpretations determining new...

  4. Description of Induced Nuclear Fission with Skyrme Energy Functionals...

    Office of Scientific and Technical Information (OSTI)

    Fragment Properties Citation Details In-Document Search Title: Description of Induced Nuclear Fission with Skyrme Energy Functionals: I. Static Potential Energy Surfaces and...

  5. Description of Induced Nuclear Fission with Skyrme Energy Functionals...

    Office of Scientific and Technical Information (OSTI)

    of Induced Nuclear Fission with Skyrme Energy Functionals: II. Finite Temperature Effects Citation Details In-Document Search Title: Description of Induced Nuclear Fission with ...

  6. Microscopic description of fission dynamics: finite element method...

    Office of Scientific and Technical Information (OSTI)

    Title: Microscopic description of fission dynamics: finite element method resolution of ... This site is a product of DOE's Office of Scientific and Technical Information (OSTI) and ...

  7. TITLE AUTHORS SUBJECT SUBJECT RELATED DESCRIPTION PUBLISHER AVAILABILI...

    Office of Scientific and Technical Information (OSTI)

    the experimental method and Free Precession Method descriptions and then experimental design elements ending with a summary A new nEDM experiment is under development with a...

  8. Descriptions of ESPC Task Order Schedules and Placement of Pricing...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Pricing Information (IDIQ Attachment J-5) Descriptions of ESPC Task Order Schedules and Placement of Pricing Information (IDIQ Attachment J-5) Document provides task order ...

  9. SSL Selections Descriptions v6.xls | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Selections Descriptions v6.xls More Documents & Publications Solid-State Lighting Recovery Act Award Selections 2015 Project Portfolio 2014 Solid-State Lighting Project Portfolio

  10. name SRSCRO description url http www srscro org namespaces oembed...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    description url http www srscro org namespaces oembed authentication routes namespace methods GET endpoints methods GET args context required false default view links self http...

  11. New Mexico Hydrogen Fuels Challenge Program Description The New...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    New Mexico Hydrogen Fuels Challenge Program Description The New Mexico Hydrogen Fuels Challenge is an event that provides a hands-on opportunity for middle school students (grades...

  12. About Additive Manufacturing | GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Introducing Additive Manufacturing at GE Global Research Click to email this to a friend (Opens in new window) Share on Facebook (Opens in new window) Click to share (Opens in new window) Click to share on LinkedIn (Opens in new window) Click to share on Tumblr (Opens in new window) Introducing Additive Manufacturing at GE Global Research Prabhjot Singh, manager of the Additive Manufacturing Lab at GE Global Research, describes the technology used in his lab. You Might Also Like DirectWrite_V

  13. Reference design description for a geologic repository: Revision 01

    SciTech Connect (OSTI)

    1997-09-01

    This document describes the current design expectations for a potential geologic repository that could be located at Yucca Mountain in Nevada. This Reference Design Description (RDD) looks at the surface and subsurface repository and disposal container design. Additionally, it reviews the expected long-term performance of the potential repository. In accordance with current legislation, the reference design for the potential repository does not include an interim storage option. The reference design presented allows the disposal of highly radioactive material received from government-owned spent fuel custodian sites; produces high-level waste sites, and commercial spent fuel sites. All design elements meet current federal, state, and local regulations governing the disposal of high-level radioactive waste and protection of the public and the environment. Due to the complex nature of developing a repository, the design will be created in three phases to support Viability Assessment, License Application, and construction. This document presents the current reference design. It will be updated periodically as the design progresses. Some of the details presented here may change significantly as more cost-effective solutions, technical advancements, or changes to requirements are identified.

  14. Novel Electrolytes and Additives | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    es023_abraham_2011_p.pdf More Documents & Publications Novel Electrolytes and Additives Progress in Electrolyte Component R&D within the ABR Program, 2009 thru 2013 Low Cost SiOx-Graphite and Olivine Materials

  15. Martin's Additions, Maryland: Energy Resources | Open Energy...

    Open Energy Info (EERE)

    is a stub. You can help OpenEI by expanding it. Martin's Additions is a village in Montgomery County, Maryland. It falls under Maryland's 8th congressional district.12...

  16. Redox Shuttle Additives - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    so does the demand for lithium-ion batteries that are safer, more powerful, and less ... A series of novel redox shuttle additives for lithium ion batteries for the purpose of ...

  17. Additional Information on the ERDF PA approach

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Technical Assistance » Better Plants » Additional Better Plants Resources Additional Better Plants Resources The Better Plants Program hosted a webinar on January 22, 2015 to review accomplishments to date and detail new initiatives to save partners energy and water. Question and answer session is included. Download the presentation slides. Read the text version. Legrand's CEO John Selldorff discusses the importance of focusing on energy efficiency and remaining competitive while being a part

  18. Gearbox Reliability Collaborative (GRC) Description and Loading

    SciTech Connect (OSTI)

    Oyague, F.

    2011-11-01

    This document describes simulated turbine load cases in accordance to the IEC 61400-1 Ed.3 standard, which is representative of the typical wind turbine design process. The information presented herein is intended to provide a broad understanding of the gearbox reliability collaborative 750kW drivetrain and turbine configuration. In addition, fatigue and ultimate strength drivetrain loads resulting from simulations are presented. This information provides the bases for the analytical work of the gearbox reliability collaborative effort.

  19. Effect of additives on lithium cycling efficiency

    SciTech Connect (OSTI)

    Hirai, Toshiro; Yoshimatsu, Isamu; Yamaki, J. )

    1994-09-01

    Lithium cycling efficiency was evaluated for LiAsF[sub 6]-ethylene carbonate/2-methyltetrahydrofuran mixed-solvent electrolyte (LiAsF[sub 6]-EC/2MeTHF) with several additives: tetraalkylammonium chlorides with a long n-alkyl chain and three methyl groups. The ammonium chlorides with n-alkyl group longer than n-C[sub 12]H[sub 25]- increased lithium cycling efficiency. Cetyltrimethylammonium chloride (CTAC) produced the best improvement in lithium cycling efficiency. A figure of merit (FOM) of lithium for 0.01 M CTAC was 46, which was 1.5 times the FOM for the corresponding additive-free electrolyte. The LiAsF[sub 6]-EC/2MeTHF with CTAC showed an increase in FOM with stack pressure, but the effect was less than that for the additive-free LiAsF[sub 6]-EC/2MeTHF. Scanning electron microscope observation showed that the addition of CTAC decreased the needle-like lithium deposition and increased particulate lithium deposition. This deposition morphology may be the main cause of the increase in FOM. The additive had no effect on rate capability for cell cycling at 3 mA/cm[sup 2] discharge and 1 mA/cm[sup 2] charge.

  20. Breaking Barriers in Polymer Additive Manufacturing

    SciTech Connect (OSTI)

    Love, Lonnie J; Duty, Chad E; Post, Brian K; Lind, Randall F; Lloyd, Peter D; Kunc, Vlastimil; Peter, William H; Blue, Craig A

    2015-01-01

    Additive Manufacturing (AM) enables the creation of complex structures directly from a computer-aided design (CAD). There are limitations that prevent the technology from realizing its full potential. AM has been criticized for being slow and expensive with limited build size. Oak Ridge National Laboratory (ORNL) has developed a large scale AM system that improves upon each of these areas by more than an order of magnitude. The Big Area Additive Manufacturing (BAAM) system directly converts low cost pellets into a large, three-dimensional part at a rate exceeding 25 kg/h. By breaking these traditional barriers, it is possible for polymer AM to penetrate new manufacturing markets.

  1. Stabilization of polyaniline solutions through additives

    DOE Patents [OSTI]

    Wrobleski, Debra A. (Los Alamos, NM); Benicewicz, Brian C. (Los Alamos, NM)

    1996-01-01

    A stabilized non-conductive polyaniline solution comprising from about 1 to bout 10 percent by weight polyaniline or a polyaniline derivative, from about 90 to about 99 percent by weight N-methylpyrrolidone, and from about 0.5 percent by weight to about 15 percent by weight of a solution stabilizing additive selected from the group consisting of hindered amine light stabilizers, polymeric amines, and dialkylamines, percent by weight of additive based on the total weight of polyaniline or polyaniline derivative is provided together with a method for stabilizing a polyaniline solution.

  2. Stabilization of polyaniline solutions through additives

    DOE Patents [OSTI]

    Wrobleski, D.A.; Benicewicz, B.C.

    1996-12-10

    A stabilized non-conductive polyaniline solution comprising from about 1 to about 10 percent by weight polyaniline or a polyaniline derivative, from about 90 to about 99 percent by weight N-methylpyrrolidone, and from about 0.5 percent by weight to about 15 percent by weight of a solution stabilizing additive selected from the group consisting of hindered amine light stabilizers, polymeric amines, and dialkylamines, percent by weight of additive based on the total weight of polyaniline or polyaniline derivative is provided together with a method for stabilizing a polyaniline solution. 4 figs.

  3. Effusion plate using additive manufacturing methods

    DOE Patents [OSTI]

    Johnson, Thomas Edward; Keener, Christopher Paul; Ostebee, Heath Michael; Wegerif, Daniel Gerritt

    2016-04-12

    Additive manufacturing techniques may be utilized to construct effusion plates. Such additive manufacturing techniques may include defining a configuration for an effusion plate having one or more internal cooling channels. The manufacturing techniques may further include depositing a powder into a chamber, applying an energy source to the deposited powder, and consolidating the powder into a cross-sectional shape corresponding to the defined configuration. Such methods may be implemented to construct an effusion plate having one or more channels with a curved cross-sectional geometry.

  4. Microscopic description of the pygmy dipole resonance and its contribution to radiative capture

    SciTech Connect (OSTI)

    Avdeyenkov, A.; Goriely, S.; Kamerdzhiev, S.; Tertychny, G.

    2009-01-28

    The radiative capture cross sections for the compound nuclei {sup 100}Sn, {sup 132}Sn and {sup 144}Nd have been calculated using both self-consistent and non-selfconsistent microscopic theories which, in addition to the standard RPA or QRPA approaches, take the single-particle continuum and phonon coupling into account. We show that the inclusion of the phonon coupling is necessary for a proper description of the pygmy resonance. Consequently, the radiative capture cross sections and corresponding rates are increased by a factor of 2-3 as compared with RPA or QRPA approaches. We conclude that the present approach provides a more complete and coherent description of the {gamma}-ray strength function than the previous models used so far and for astrophysics applications in particular, such calculations are highly recommended for a more reliable estimate of the electromagnetic properties of exotic nuclei.

  5. Preconceptual Design Description for Caustic Recycle Facility

    SciTech Connect (OSTI)

    Sevigny, Gary J.; Poloski, Adam P.; Fountain, Matthew S.; Kurath, Dean E.

    2008-04-12

    The U.S. Department of Energy plans to vitrify both high-level and low-activity waste at the Hanford Site in southeastern Washington State. One aspect of the planning includes a need for a caustic recycle process to separate sodium hydroxide for recycle. Sodium is already a major limitation to the waste-oxide loading in the low-activity waste glass to be vitrified at the Waste Treatment Plant, and additional sodium hydroxide will be added to remove aluminum and to control precipitation in the process equipment. Aluminum is being removed from the high level sludge to reduce the number of high level waste canisters produced. A sodium recycle process would reduce the volume of low-activity waste glass produced and minimize the need to purchase new sodium hydroxide, so there is a renewed interest in investigating sodium recycle. This document describes an electrochemical facility for recycling sodium for the WTP.

  6. INL Wind Farm Project Description Document

    SciTech Connect (OSTI)

    Gary Siefert

    2009-07-01

    The INL Wind Farm project proposes to install a 20 MW to 40 MW wind farm on government property, consisting of approximately ten to twenty full-sized (80-meter hub height) towers with 2 MW turbines, and access roads. This includes identifying the optimal turbine locations, building access roads, and pouring the tower foundations in preparation for turbine installation. The project successfully identified a location on INL lands with commercially viable wind resources (i.e., greater than 11 mph sustained winds) for a 20 to 40 MW wind farm. Additionally, the proposed Wind Farm was evaluated against other General Plant Projects, General Purpose Capital Equipment projects, and Line Item Construction Projects at the INL to show the relative importance of the proposed Wind Farm project.

  7. Vehicular fuels and additives for the future

    SciTech Connect (OSTI)

    Not Available

    1988-01-01

    Interest in automotive fuel is resurging. Automobile fuels must increasingly deal with clean air regulations and ozone problems. Furthermore, feedstocks become heavier,as refinery production changes, as more unleaded is produced, and as an increasing number of pollution regulations must be satisfied greater attention will be paid to better mixtures, solvents, additives, and neat methanol. BCC report analyzes developments technologies, markets, players and the political/regulations aspects of this important market. Study also assesses the advantages and drawbacks of methanol, ethanol, MTBE and other additives which have their place as octane enhancers and fuel substitutes-all now deeply involved in the gasoline modification battle. Other issues addressed are subsidies, farm lobbying, imports, pricing, economics, Detroit's response, neat fuel testing projects, volatility problems vs. fewer ozone-forming hydrocarbon species, and emission ratings.

  8. Evolution of solidification texture during additive manufacturing

    SciTech Connect (OSTI)

    Wei, H. L.; Mazumder, J.; DebRoy, T.

    2015-11-10

    Striking differences in the solidification textures of a nickel based alloy owing to changes in laser scanning pattern during additive manufacturing are examined based on theory and experimental data. Understanding and controlling texture are important because it affects mechanical and chemical properties. Solidification texture depends on the local heat flow directions and competitive grain growth in one of the six <100> preferred growth directions in face centered cubic alloys. Furthermore, the heat flow directions are examined for various laser beam scanning patterns based on numerical modeling of heat transfer and fluid flow in three dimensions. Here we show that numerical modeling can not only provide a deeper understanding of the solidification growth patterns during the additive manufacturing, it also serves as a basis for customizing solidification textures which are important for properties and performance of components.

  9. Evolution of solidification texture during additive manufacturing

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Wei, H. L.; Mazumder, J.; DebRoy, T.

    2015-11-10

    Striking differences in the solidification textures of a nickel based alloy owing to changes in laser scanning pattern during additive manufacturing are examined based on theory and experimental data. Understanding and controlling texture are important because it affects mechanical and chemical properties. Solidification texture depends on the local heat flow directions and competitive grain growth in one of the six <100> preferred growth directions in face centered cubic alloys. Furthermore, the heat flow directions are examined for various laser beam scanning patterns based on numerical modeling of heat transfer and fluid flow in three dimensions. Here we show that numericalmore » modeling can not only provide a deeper understanding of the solidification growth patterns during the additive manufacturing, it also serves as a basis for customizing solidification textures which are important for properties and performance of components.« less

  10. The addition of disilanes to cumulenes

    SciTech Connect (OSTI)

    Chen, Y.

    1997-10-08

    The syntheses of silicon-containing compounds and the studies of their rearrangements have been active research areas in the Barton research group. Previously, the addition of disilanes to acetylenes was studied in the group and an intramolecular 2S + 2A mechanism has been proposed. In this thesis, the work is focused on the addition of disilanes to cumulenes. The syntheses of the precursors are discussed and the possible mechanisms for their thermal, photochemical and catalytic rearrangements are proposed. Conjugated organic polymers have been studied in the group since 1985 because of their potential for exhibiting high electroconductivity, photoconductivity, strong non-linear optical response and intense fluorescence. In the second section of this dissertation, the synthesis and property studies of poly(phenylene vinylene) analogues are discussed.

  11. Minnesota Natural Gas LNG Storage Additions (Million Cubic Feet...

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Minnesota Natural Gas LNG Storage Additions (Million Cubic ... Additions of Liquefied Natural Gas into Storage Minnesota Liquefied Natural Gas Additions ...

  12. California Natural Gas LNG Storage Additions (Million Cubic Feet...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Additions (Million Cubic Feet) California Natural Gas LNG Storage Additions (Million Cubic ... Additions of Liquefied Natural Gas into Storage California Liquefied Natural Gas Additions ...

  13. NOVEL LUBRICANT ADDITIVES - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Find More Like This Return to Search NOVEL LUBRICANT ADDITIVES Argonne National Laboratory Contact ANL About This Technology <em>Upper, the functionalized nanostructures mixed with poly-alpha-olefin (PAO)-4 reduce friction as test temperature is raised. Lower, Friction coefficient remains unchanged at all test temperatures with PAO4 alone.&nbsp; </em><br /> Upper, the functionalized nanostructures mixed with poly-alpha-olefin (PAO)-4 reduce friction as test temperature is

  14. Energetic additive manufacturing process with feed wire

    DOE Patents [OSTI]

    Harwell, Lane D.; Griffith, Michelle L.; Greene, Donald L.; Pressly, Gary A.

    2000-11-07

    A process for additive manufacture by energetic wire deposition is described. A source wire is fed into a energy beam generated melt-pool on a growth surface as the melt-pool moves over the growth surface. This process enables the rapid prototyping and manufacture of fully dense, near-net shape components, as well as cladding and welding processes. Alloys, graded materials, and other inhomogeneous materials can be grown using this process.

  15. Additional Resources | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Development Additional Resources Photo: DARHT's Accelerators help create the x-rays at DARHT, the world's most advanced radiography facility. Reports 2013 Stewardship Science Academic Programs Annual 2012 Stewardship Science Academic Alliances Annual 2011 Stewardship Science Academic Alliances Annual FY 2011 Stockpile Stewardship and Management Plan, Annex A (April 7, 2010) Supplement to the Stockpile Stewardship Plan, Fiscal Years 2010-2014 (December 2009) Advances in Matter Under Extreme

  16. Consolidated Nuclear Security announces additional leadership changes |

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Y-12 National Security Complex Consolidated Nuclear ... Consolidated Nuclear Security announces additional leadership changes Posted: February 15, 2016 - 2:29pm OAK RIDGE, Tenn. - Effective today, Feb. 15, 2016, Michelle Reichert becomes the Deputy Enterprise Manager for Consolidated Nuclear Security, LLC (CNS), reporting directly to CNS President and CEO Morgan Smith. CNS is the managing and operating contractor for two key national security facilities: the Pantex Plant in Amarillo, Texas,

  17. Microsoft Word - Appendix D_LegalDescription.doc

    Office of Legacy Management (LM)

    Boundary for the Chemical Plant Area Weldon Spring Site LTS&M Plan U.S. Department of Energy Doc. No. S0079000 July 2005 Page D-4 Legal Description for the Chemical Plant Area All ...

  18. Hanford Site existing irradiated fuel storage facilities description

    SciTech Connect (OSTI)

    Willis, W.L.

    1995-01-11

    This document describes facilities at the Hanford Site which are currently storing spent nuclear fuels. The descriptions provide a basis for the no-action alternatives of ongoing and planned National Environmental Protection Act reviews.

  19. Comparative assessment of TRU waste forms and processes. Volume II. Waste form data, process descriptions, and costs.

    SciTech Connect (OSTI)

    Ross, W.A.; Lokken, R.O.; May, R.P.; Roberts, F.P.; Thornhill, R.E.; Timmerman, C.L.; Treat, R.L.; Westsik, J.H. Jr.

    1982-09-01

    This volume contains supporting information for the comparative assessment of the transuranic waste forms and processes summarized in Volume I. Detailed data on the characterization of the waste forms selected for the assessment, process descriptions, and cost information are provided. The purpose of this volume is to provide additional information that may be useful when using the data in Volume I and to provide greater detail on particular waste forms and processes. Volume II is divided into two sections and two appendixes. The first section provides information on the preparation of the waste form specimens used in this study and additional characterization data in support of that in Volume I. The second section includes detailed process descriptions for the eight processes evaluated. Appendix A lists the results of MCC-1 leach test and Appendix B lists additional cost data. 56 figures, 12 tables.

  20. General integral relations for the description of scattering states using

    Office of Scientific and Technical Information (OSTI)

    the hyperspherical adiabatic basis (Journal Article) | SciTech Connect General integral relations for the description of scattering states using the hyperspherical adiabatic basis Citation Details In-Document Search Title: General integral relations for the description of scattering states using the hyperspherical adiabatic basis In this work we investigate 1+2 reactions within the framework of the hyperspherical adiabatic expansion method. With this aim two integral relations, derived from

  1. Microscopic Description of Induced Nuclear Fission (Conference) | SciTech

    Office of Scientific and Technical Information (OSTI)

    Connect Microscopic Description of Induced Nuclear Fission Citation Details In-Document Search Title: Microscopic Description of Induced Nuclear Fission Authors: Schunck, N Publication Date: 2012-12-13 OSTI Identifier: 1059062 Report Number(s): LLNL-PROC-608273 DOE Contract Number: W-7405-ENG-48 Resource Type: Conference Resource Relation: Conference: Presented at: 10th International Conference on Clustering Aspects of Nuclear Structure and Dynamics, Debrecen, Hungary, Sep 24 - Sep 28

  2. Microscopic Description of Nuclear Fission: Fission Barrier Heights of

    Office of Scientific and Technical Information (OSTI)

    Even-Even Actinides (Conference) | SciTech Connect Microscopic Description of Nuclear Fission: Fission Barrier Heights of Even-Even Actinides Citation Details In-Document Search Title: Microscopic Description of Nuclear Fission: Fission Barrier Heights of Even-Even Actinides Authors: McDonnell, J ; Schunck, N ; Nazarewicz, W Publication Date: 2013-01-22 OSTI Identifier: 1062216 Report Number(s): LLNL-PROC-612272 DOE Contract Number: W-7405-ENG-48 Resource Type: Conference Resource Relation:

  3. Microscopic description of fission dynamics: finite element method

    Office of Scientific and Technical Information (OSTI)

    resolution of the TDGCM+GOA equation (Conference) | SciTech Connect Conference: Microscopic description of fission dynamics: finite element method resolution of the TDGCM+GOA equation Citation Details In-Document Search Title: Microscopic description of fission dynamics: finite element method resolution of the TDGCM+GOA equation Authors: Regnier, D ; Dubray, N ; Schunck, N ; Verriere, M Publication Date: 2015-10-16 OSTI Identifier: 1239187 Report Number(s): LLNL-PROC-678472 DOE Contract

  4. OMB 1910-5122, Human Reliability Program - Description of Collections |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy OMB 1910-5122, Human Reliability Program - Description of Collections OMB 1910-5122, Human Reliability Program - Description of Collections Human Reliability Program Certification (DOE F 470.3). Under the Department of Energy Human Reliability Program (HRP), individuals who are applicants for or incumbents in designated positions must be evaluated to ensure that they meet the requirements for certification in the program. This form documents that each part of the

  5. Physical Description and Experimental Characterization of the Resistive

    Office of Scientific and Technical Information (OSTI)

    Switching Filament. (Conference) | SciTech Connect Physical Description and Experimental Characterization of the Resistive Switching Filament. Citation Details In-Document Search Title: Physical Description and Experimental Characterization of the Resistive Switching Filament. Abstract not provided. Authors: Lohn, Andrew ; Mickel, Patrick R. ; James, Conrad D. ; Marinella, Matthew Publication Date: 2014-02-01 OSTI Identifier: 1141260 Report Number(s): SAND2014-1499C 504908 DOE Contract

  6. Descriptive Model of a Generic WAMS | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Descriptive Model of a Generic WAMS Descriptive Model of a Generic WAMS The Department of Energy's (DOE) Transmission Reliability Program is supporting the research, deployment, and demonstration of various wide area measurement system (WAMS) technologies to enhance the reliability of the Nation's electrical power grid. Pacific Northwest National Laboratory (PNNL) was tasked by the DOE National SCADA Test Bed Program to conduct a study of WAMS security. This report represents achievement of the

  7. Description of Induced Nuclear Fission with Skyrme Energy Functionals: II.

    Office of Scientific and Technical Information (OSTI)

    Finite Temperature Effects (Journal Article) | SciTech Connect Journal Article: Description of Induced Nuclear Fission with Skyrme Energy Functionals: II. Finite Temperature Effects Citation Details In-Document Search Title: Description of Induced Nuclear Fission with Skyrme Energy Functionals: II. Finite Temperature Effects Authors: Schunck, N ; Duke, D ; Carr, H Publication Date: 2013-11-06 OSTI Identifier: 1184748 Report Number(s): LLNL-JRNL-645837 DOE Contract Number: DE-AC52-07NA27344

  8. Summary description of the Fast Flux Test Facility

    SciTech Connect (OSTI)

    Cabell, C.P.

    1980-12-01

    This document has been compiled and issued to provide an illustrated engineering summary description of the FFTF. The document is limited to a description of the plant and its functions, and does not cover the extensive associated programs that have been carried out in the fields of design, design analysis, safety analysis, fuels development, equipment development and testing, quality assurance, equipment fabrication, plant construction, acceptance testing, operations planning and training, and the like.

  9. Toward a Minimal Representation of Aerosols in Climate Models: Description

    Office of Scientific and Technical Information (OSTI)

    and Evaluation in the Community Atmosphere Model CAM5 (Journal Article) | SciTech Connect Toward a Minimal Representation of Aerosols in Climate Models: Description and Evaluation in the Community Atmosphere Model CAM5 Citation Details In-Document Search Title: Toward a Minimal Representation of Aerosols in Climate Models: Description and Evaluation in the Community Atmosphere Model CAM5 A modal aerosol module (MAM) has been developed for the Community Atmosphere Model version 5 (CAM5), the

  10. Variational description of continuum states in terms of integral relations

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect Variational description of continuum states in terms of integral relations Citation Details In-Document Search Title: Variational description of continuum states in terms of integral relations Two integral relations derived from the Kohn variational principle (KVP) are used for describing scattering states. In usual applications the KVP requires the explicit form of the asymptotic behavior of the scattering wave function. This is not the case when the

  11. Consistent description of kinetics and hydrodynamics of dusty plasma

    SciTech Connect (OSTI)

    Markiv, B.; Tokarchuk, M.; National University Lviv Polytechnic, 12 Bandera St., 79013 Lviv

    2014-02-15

    A consistent statistical description of kinetics and hydrodynamics of dusty plasma is proposed based on the Zubarev nonequilibrium statistical operator method. For the case of partial dynamics, the nonequilibrium statistical operator and the generalized transport equations for a consistent description of kinetics of dust particles and hydrodynamics of electrons, ions, and neutral atoms are obtained. In the approximation of weakly nonequilibrium process, a spectrum of collective excitations of dusty plasma is investigated in the hydrodynamic limit.

  12. Electrolyte additive for improved battery performance

    DOE Patents [OSTI]

    Bellows, Richard J. (Hampton, NJ); Kantner, Edward (E. Brunswick, NJ)

    1989-04-04

    In one embodiment of the present invention, there is provided an electrochemical cell having a metal bromine couple. The cell includes an electrode structure on which to deposit the metal of the couple and a counterelectrode at which to generate bromine. A microporous membrane separates the electrode and counterelectrode. Importantly, the aqueous electrolyte comprises an aqueous metal bromide solution containing a water soluble bromine complexing agent capable of forming a water immiscible complex with bromine and an additive capable of decreasing the wettability of the microporous separators employed in such cells by such water immiscible bromine complexes.

  13. DESCRIPTION OF THE SOFTWARE AND INTEGRATING PLATFORM

    SciTech Connect (OSTI)

    Flach, G.

    2009-12-31

    The Cementitious Barriers Partnership (CBP) Project is a multi-disciplinary, multi-institutional collaboration supported by the United States Department of Energy (US DOE) Office of Waste Processing. The objective of the CBP project is to develop a set of tools to improve understanding and prediction of the long-term structural, hydraulic, and chemical performance of cementitious barriers used in nuclear applications. A multi-disciplinary partnership of federal, academic, private sector, and international expertise has been formed to accomplish the project objective. In addition to the US DOE, the CBP partners are the Savannah River National Laboratory (SRNL), Vanderbilt University (VU)/Consortium for Risk Evaluation with Stakeholder Participation (CRESP), Energy Research Center of the Netherlands (ECN), and SIMCO Technologies, Inc. The Nuclear Regulatory Commission (NRC) is providing support under a Memorandum of Understanding. The National Institute of Standards and Technology (NIST) is providing research under an Interagency Agreement. Neither the NRC nor NIST are signatories to the CRADA. The periods of cementitious performance being evaluated are >100 years for operating facilities and > 1000 years for waste management. The set of simulation tools and data developed under this project will be used to evaluate and predict the behavior of cementitious barriers used in near surface engineered waste disposal systems, e.g., waste forms, containment structures, entombments, and environmental remediation, including decontamination and decommissioning analysis of structural concrete components of nuclear facilities (spent-fuel pools, dry spent-fuel storage units, and recycling facilities such as fuel fabrication, separations processes). Simulation parameters will be obtained from prior literature and will be experimentally measured under this project, as necessary, to demonstrate application of the simulation tools for three prototype applications (waste form in concrete vault, high-level waste tank grouting, and spent-fuel pool). Test methods and data needs to support use of the simulation tools for future applications will be defined. The CBP project is a five-year effort focused on reducing the uncertainties of current methodologies for assessing cementitious barrier performance and increasing the consistency and transparency of the assessment process. The results of this project will enable improved risk-informed, performance-based decision-making and support several of the strategic initiatives in the DOE Office of Environmental Management Engineering & Technology Roadmap. Those strategic initiatives include (1) enhanced tank closure processes; (2) enhanced stabilization technologies; (3) advanced predictive capabilities; (4) enhanced remediation methods; (5) adapted technologies for site-specific and complex-wide D&D applications; (6) improved SNF storage, stabilization and disposal preparation; (7) enhanced storage, monitoring and stabilization systems; and (8) enhanced long-term performance evaluation and monitoring.

  14. Description of Axial Detail for ROK Fuel

    SciTech Connect (OSTI)

    Trellue, Holly R; Galloway, Jack D

    2012-04-20

    For the purpose of NDA simulations of the ROK fuel assemblies, we have developed an axial burnup distribution to represent the pins themselves based on gamma scans of rods in the G23 assembly. For the purpose of modeling the G23 assembly (both at ORNL and LANL), the pin-by-pin burnup map as simulated by ROK is being assumed to represent the radial burnup distribution. However, both DA and NDA results indicate that this simulated estimate is not 100% correct. In particular, the burnup obtained from the axial gamma scan of 7 pins does not represent exactly the same 'average' pin burnup as the ROK simulation. Correction for this discrepancy is a goal of the well-characterized assembly task but will take time. For now, I have come up with a correlation for 26 axial points of the burnup as obtained by gamma scans of 7 different rods (C13, G01, G02, J11, K10, L02, and M04, neglecting K02 at this time) to the average burnup given by the simulation for each of the rods individually. The resulting fraction in each axial zone is then averaged for the 7 different rods so that it can represent every fuel pin in the assembly. The burnup in each of the 26 axial zones of rods in all ROK assemblies will then be directly adjusted using this fraction, which is given in Table 1. Note that the gamma scan data given by ROK for assembly G23 included a length of {approx}3686 mm, so the first 12 mm and the last 14 mm were ignored to give an actual rod length of {approx}366 cm. To represent assembly F02 in which no pin-by-pin burnup distribution is given by ROK, we must model it using infinitely-reflected geometry but can look at the effects of measuring in different axial zones by using intermediate burnup files (i.e. smaller burnups than 28 GWd/MTU) and determining which axial zone(s) each burnup represents. Details for assembly F02 are then given in Tables 2 and 3, which is given in Table 1 and has 44 total axial zones to represent the top meter in explicit detail in addition to the other 26 zones. Note that the MCNP files for F02 were created using the Monte Carlo burnup linkage code Monteburns, which saves MCNP input files with detailed compositions as a function of burnup. The 'intermediate burnup files' produced for F02 include a cooling time of 27 years. The axial location of 5 spacers was also included in the ROK F02 assembly in which each spacer contained a length of 3.81 cm. Note that due to the nature of Monteburns, which was run in a special fashion for this problem, the step number increments after the 27 year decay, so the second column of Table 2 refers to the step number that should be used in the Monteburns files.

  15. Beam geometry selection using sequential beam addition

    SciTech Connect (OSTI)

    Popple, Richard A. Brezovich, Ivan A.; Fiveash, John B.

    2014-05-15

    Purpose: The selection of optimal beam geometry has been of interest since the inception of conformal radiotherapy. The authors report on sequential beam addition, a simple beam geometry selection method, for intensity modulated radiation therapy. Methods: The sequential beam addition algorithm (SBA) requires definition of an objective function (score) and a set of candidate beam geometries (pool). In the first iteration, the optimal score is determined for each beam in the pool and the beam with the best score selected. In the next iteration, the optimal score is calculated for each beam remaining in the pool combined with the beam selected in the first iteration, and the best scoring beam is selected. The process is repeated until the desired number of beams is reached. The authors selected three treatment sites, breast, lung, and brain, and determined beam arrangements for up to 11 beams from a pool comprised of 25 equiangular transverse beams. For the brain, arrangements were additionally selected from a pool of 22 noncoplanar beams. Scores were determined for geometries comprised equiangular transverse beams (EQA), as well as two tangential beams for the breast case. Results: In all cases, SBA resulted in scores superior to EQA. The breast case had the strongest dependence on beam geometry, for which only the 7-beam EQA geometry had a score better than the two tangential beams, whereas all SBA geometries with more than two beams were superior. In the lung case, EQA and SBA scores monotonically improved with increasing number of beams; however, SBA required fewer beams to achieve scores equivalent to EQA. For the brain case, SBA with a coplanar pool was equivalent to EQA, while the noncoplanar pool resulted in slightly better scores; however, the dose-volume histograms demonstrated that the differences were not clinically significant. Conclusions: For situations in which beam geometry has a significant effect on the objective function, SBA can identify arrangements equivalent to equiangular geometries but using fewer beams. Furthermore, SBA provides the value of the objective function as the number of beams is increased, allowing the planner to select the minimal beam number that achieves the clinical goals. The method is simple to implement and could readily be incorporated into an existing optimization system.

  16. Printability of alloys for additive manufacturing

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Mukherjee, T.; Zuback, J. S.; De, A.; DebRoy, T.

    2016-01-22

    Although additive manufacturing (AM), or three dimensional (3D) printing, provides significant advantages over existing manufacturing techniques, metallic parts produced by AM are susceptible to distortion, lack of fusion defects and compositional changes. Here we show that the printability, or the ability of an alloy to avoid these defects, can be examined by developing and testing appropriate theories. A theoretical scaling analysis is used to test vulnerability of various alloys to thermal distortion. A theoretical kinetic model is used to examine predisposition of different alloys to AM induced compositional changes. A well-tested numerical heat transfer and fluid flow model is usedmore » to compare susceptibilities of various alloys to lack of fusion defects. These results are tested and validated with independent experimental data. Here, the findings presented in this paper are aimed at achieving distortion free, compositionally sound and well bonded metallic parts.« less

  17. Additional EIPC Study Analysis. Final Report

    SciTech Connect (OSTI)

    Hadley, Stanton W; Gotham, Douglas J.; Luciani, Ralph L.

    2014-12-01

    Between 2010 and 2012 the Eastern Interconnection Planning Collaborative (EIPC) conducted a major long-term resource and transmission study of the Eastern Interconnection (EI). With guidance from a Stakeholder Steering Committee (SSC) that included representatives from the Eastern Interconnection States Planning Council (EISPC) among others, the project was conducted in two phases. Phase 1 involved a long-term capacity expansion analysis that involved creation of eight major futures plus 72 sensitivities. Three scenarios were selected for more extensive transmission- focused evaluation in Phase 2. Five power flow analyses, nine production cost model runs (including six sensitivities), and three capital cost estimations were developed during this second phase. The results from Phase 1 and 2 provided a wealth of data that could be examined further to address energy-related questions. A list of 14 topics was developed for further analysis. This paper brings together the earlier interim reports of the first 13 topics plus one additional topic into a single final report.

  18. Structure Property Studies for Additively Manufactured Parts

    SciTech Connect (OSTI)

    Milenski, Helen M; Schmalzer, Andrew Michael; Kelly, Daniel

    2015-08-17

    Since the invention of modern Additive Manufacturing (AM) processes engineers and designers have worked hard to capitalize on the unique building capabilities that AM allows. By being able to customize the interior fill of parts it is now possible to design components with a controlled density and customized internal structure. The creation of new polymers and polymer composites allow for even greater control over the mechanical properties of AM parts. One of the key reasons to explore AM, is to bring about a new paradigm in part design, where materials can be strategically optimized in a way that conventional subtractive methods cannot achieve. The two processes investigated in my research were the Fused Deposition Modeling (FDM) process and the Direct Ink Write (DIW) process. The objectives of the research were to determine the impact of in-fill density and morphology on the mechanical properties of FDM parts, and to determine if DIW printed samples could be produced where the filament diameter was varied while the overall density remained constant.

  19. Waste receiving and processing plant control system; system design description

    SciTech Connect (OSTI)

    LANE, M.P.

    1999-02-24

    The Plant Control System (PCS) is a heterogeneous computer system composed of numerous sub-systems. The PCS represents every major computer system that is used to support operation of the Waste Receiving and Processing (WRAP) facility. This document, the System Design Description (PCS SDD), includes several chapters and appendices. Each chapter is devoted to a separate PCS sub-system. Typically, each chapter includes an overview description of the system, a list of associated documents related to operation of that system, and a detailed description of relevant system features. Each appendice provides configuration information for selected PCS sub-systems. The appendices are designed as separate sections to assist in maintaining this document due to frequent changes in system configurations. This document is intended to serve as the primary reference for configuration of PCS computer systems. The use of this document is further described in the WRAP System Configuration Management Plan, WMH-350, Section 4.1.

  20. Unified description of superconducting pairing symmetry in electron-doped

    Office of Scientific and Technical Information (OSTI)

    Fe-based-122 compounds (Journal Article) | SciTech Connect Unified description of superconducting pairing symmetry in electron-doped Fe-based-122 compounds Citation Details In-Document Search This content will become publicly available on June 25, 2016 Title: Unified description of superconducting pairing symmetry in electron-doped Fe-based-122 compounds Authors: Li, Bo ; Pan, Lihua ; Tai, Yuan-Yen ; Graf, Matthias J. ; Zhu, Jian-Xin ; Bassler, Kevin E. ; Ting, C. S. Publication Date:

  1. Develop and Evaluate Materials and Additives that Enhance Thermal...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Develop & Evaluate Materials & Additives that Enhance Thermal & Overcharge Abuse Develop & Evaluate Materials & Additives that Enhance Thermal & Overcharge Abuse High Voltage ...

  2. Develop and Evaluate Materials and Additives that Enhance Thermal...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications Develop & evaluate materials & additives that enhance thermal & overcharge abuse Develop & Evaluate Materials & Additives that Enhance Thermal & ...

  3. Tokamak Physics EXperiment (TPX): Toroidal field magnet design, development and manufacture. SDRL 15, System design description. Volume 1

    SciTech Connect (OSTI)

    1995-09-22

    This System Design Description, prepared in accordance with the TPX Project Management Plan provides a summary or TF Magnet System design features at the conclusion of Phase I, Preliminary Design and Manufacturing Research. The document includes the analytical and experimental bases for the design, and plans for implementation in final design, manufacturing, test, and magnet integration into the tokamak. Requirements for operation and maintenance are outlined, and references to sources of additional information are provided.

  4. TITLE AUTHORS SUBJECT SUBJECT RELATED DESCRIPTION PUBLISHER AVAILABILI...

    Office of Scientific and Technical Information (OSTI)

    An Overview of Polymer Additive Manufacturing Technologies Peterson Dominic S Los Alamos National Laboratory Los Alamos National Laboratory Materials Science Additive Manufacturing...

  5. TITLE AUTHORS SUBJECT SUBJECT RELATED DESCRIPTION PUBLISHER AVAILABILI...

    Office of Scientific and Technical Information (OSTI)

    COMPOUNDS In recent years Electron Beam Melting EBM has matured as a technology for additive manufacturing of dense metal parts The parts are built by additive consolidation...

  6. Tank Waste Remediation System (TWRS) Technical Baseline Summary Description

    SciTech Connect (OSTI)

    TEDESCHI, A.R.

    2000-04-21

    This revision notes the supersedure of the subject document by concurrent issuance of HNF-1901 ''Technical Baseline Summary Description for the Tank Farm Contractor'', Revision 2. Safe storage mission technical baseline information was absorbed by the new revision of HNF-1901.

  7. Tank waste remediation system technical baseline summary description

    SciTech Connect (OSTI)

    Raymond, R.E.

    1998-01-08

    This document is one of the tools used to develop and control the mission work as depicted in the included figure. This Technical Baseline Summary Description document is the top-level tool for management of the Technical Baseline for waste storage operations.

  8. SPEAR fuel reliability code system. General description. [PWR; BWR

    SciTech Connect (OSTI)

    Christensen, R.

    1980-03-01

    A general description is presented for the SPEAR fuel reliability code system. Included is a discussion of the methodology employed and the structure of the code system, as well as discussion of the major components: the data preparation routines, the mechanistic fuel performance model, the mechanistic cladding failure model, and the statistical failure model.

  9. A climatological description of the Savannah River Site

    SciTech Connect (OSTI)

    Hunter, C.H.

    1990-05-22

    This report provides a general climatological description of the Savannah River Site. The description provides both regional and local scale climatology. The regional climatology includes a general regional climatic description and presents information on occurrence frequencies of the severe meteorological phenomena that are important considerations in the design and siting of a facility. These phenomena include tornadoes, thunderstorms, hurricanes, and ice/snow storms. Occurrence probabilities given for extreme tornado and non-tornado winds are based on previous site specific studies. Local climatological conditions that are significant with respect to the impact of facility operations on the environment are described using on-site or near-site meteorological data. Summaries of wind speed, wind direction, and atmospheric stability are primarily based on the most recently generated five-year set of data collected from the onsite meteorological tower network (1982--86). Temperature, humidity, and precipitation summaries include data from SRL's standard meteorological instrument shelter and the Augusta National Weather Service office at Bush Field through 1986. A brief description of the onsite meteorological monitoring program is also provided. 24 refs., 15 figs., 22 tabs.

  10. ACTION DESCRIPTION MEMORANDUM PROPOSED DECONTAMINATION OF THREE BUILDINGS AT THE

    Office of Legacy Management (LM)

    ACTION DESCRIPTION MEMORANDUM PROPOSED DECONTAMINATION OF THREE BUILDINGS AT THE UNIVERSITY OF CHICAGO CONTAMINATED AS A RESULT OF PREVIOUS MED/AEC ACTIVITIES Prepared by Environmental Research Division Argonne National Laboratory Argonne, Illinois December 1983 Prepared for U.S. Department of Energy Oak Ridge Operations Technical Services Division Oak Ridge, Tennessee II-39 CONTENTS Page Summary of Proposed Action ....................... 1 Setting . . . . . . . . . . . . . . . . . . . . . . . .

  11. Computer System, Cluster, and Networking Summer Institute Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    System, Cluster, and Networking Summer Institute Program Description The Computer System, Cluster, and Networking Summer Institute (CSCNSI) is a focused technical enrichment program targeting third-year college undergraduate students currently engaged in a computer science, computer engineering, or similar major. The program emphasizes practical skill development in setting up, configuring, administering, testing, monitoring, and scheduling computer systems, supercomputer clusters, and computer

  12. Description of recommended non-thermal mixed waste treatment technologies: Version 1.0

    SciTech Connect (OSTI)

    1995-08-01

    This document contains description of the technologies selected for inclusions in the Integrated Nonthermal Treatment Systems (INTS) Study. The purpose of these descriptions is to provide a more complete description of the INTS technologies. It supplements the summary descriptions of candidate nonthermal technologies that were considered for the INTS.

  13. Additive Manufacturing: Pursuing the Promise | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Additive Manufacturing: Pursuing the Promise Additive Manufacturing: Pursuing the Promise Fact sheet overviewing additive manufacturing techniques that are projected to exert a profound impact on manufacturing. PDF icon Additive Manufacturing: Pursuing the Promise More Documents & Publications QTR Webinar: Chapter 8 - Industry and Manufacturing WORKSHOP: SUSTAINABILITY IN MANUFACTURING, JANUARY 6-7 Unlocking the Potential of Additive Manufacturing in the Fuel Cells Industry

  14. Task Descriptions | Center for Bio-Inspired Solar Fuel Production

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Task Descriptions Center for Bio-Inspired Solar Fuel Production Central to design of a complete system for solar water oxidation and hydrogen production is incorporation of synthetic components inspired by natural systems into one operational unit. The research effort of the Center is naturally divided into the following subtasks: Subtask 1. Total systems analysis, assembly and testing The solar water splitting device consists of four subsystems, each of which is being investigated by one of the

  15. Description of induced nuclear fission with Skyrme energy functionals:

    Office of Scientific and Technical Information (OSTI)

    Static potential energy surfaces and fission fragment properties (Journal Article) | SciTech Connect functionals: Static potential energy surfaces and fission fragment properties Citation Details In-Document Search Title: Description of induced nuclear fission with Skyrme energy functionals: Static potential energy surfaces and fission fragment properties Authors: Schunck, N. ; Duke, D. ; Carr, H. ; Knoll, A. Publication Date: 2014-11-06 OSTI Identifier: 1180689 Grant/Contract Number:

  16. Postdoctoral Program Program Description The Postdoctoral (Postdoc) Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Postdoctoral Program Program Description The Postdoctoral (Postdoc) Research program offers the opportunity for appointees to perform research in a robust scientific R&D environment, present and publish research, advance knowledge in basic and applied science, and strengthen national scientific and technical capabilities. Program Mission The Postdoctoral Program provides the opportunity for appointees to perform scientifically rich research, showcase their work through publishing and

  17. 2010-12-1-DICE-Diagnostic-Service-Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Editor: Joe Metzger Status: DRAFT (v1.0) Date: 2010-12-1 1 General Service Description for DICE Network Diagnostic Services The DICE collaboration network diagnostic service will simplify the process of debugging, isolating, and correcting multi-domain network performance problems. The diagnostic service will allow users to measure network characteristics across multi-domain network paths. The service is designed to support network engineers in situations where a customer is experiencing

  18. ADDENDUM TO ACTION DESCRIPTION MEMORANDUM NIAGARA FALLS STORAGE SITE

    Office of Legacy Management (LM)

    ADDENDUM TO ACTION DESCRIPTION MEMORANDUM NIAGARA FALLS STORAGE SITE PROPOSED INTERIM REMEDIAL ACTIONS FOR FY 1983-85 ACCELERATED PROGRAM (1984 VICINITY PROPERTIES CLEANUP) Prepared by Environmental Research Division Argonne National Laboratory Argonne, Illinois July 1984 Prepared for U.S. Department of Energy Oak Ridge Operations Technical Services Division Oak Ridge, Tennessee CONTENTS Page SUMMARY OF PROPOSED ACTION AND RELATED ACTIVITIES ........... 1 HISTORY AND ENVIRONMENTAL SETTING

  19. ARM Value-Added Cloud Products: Description and Status

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Value-Added Cloud Products: Description and Status M. A. Miller, K. L. Johnson, and D. T. Troyan Brookhaven National Laboratory Upton, New York E. E. Clothiaux Pennsylvania State University University Park, Pennsylvania E. J. Mlawer Atmospheric and Environmental Research, Inc. Cambridge, Massachusetts G. G. Mace University of Utah Salt Lake City, Utah Introduction The Atmospheric Radiation Measurement (ARM) Program operates a variety of state-of-the-art active and passive remote sensors at its

  20. Community College Institute (CCI) Program Description The Community College Internship

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Community College Institute (CCI) Program Description The Community College Internship (CCI) program seeks to encourage community college students to enter technical careers relevant to the DOE mission by providing technical training experiences at the DOE laboratories. Selected students participate as interns appointed at one of 15 participating DOE laboratories. They work on technologies or instrumentation projects at major research facilities supporting DOE's mission under the guidance of

  1. Experimental and Theoretical Investigation of Lubricant and Additive...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Theoretical Investigation of Lubricant and Additive Effects on Engine Friction Experimental and Theoretical Investigation of Lubricant and Additive Effects on Engine Friction ...

  2. Multi-component Nanoparticle Based Lubricant Additive to Improve...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Nanoparticle Based Lubricant Additive to Improve Efficiency and Durability in Engines Multi-component Nanoparticle Based Lubricant Additive to Improve Efficiency and ...

  3. Fuel Additive Strategies for Enhancing the Performance of Engines...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Additive Strategies for Enhancing the Performance of Engines and Engine Oils Fuel Additive Strategies for Enhancing the Performance of Engines and Engine Oils 2003 DEER Conference ...

  4. An Overview of Polymer Additive Manufacturing Technologies (Technical...

    Office of Scientific and Technical Information (OSTI)

    An Overview of Polymer Additive Manufacturing Technologies Citation Details In-Document Search Title: An Overview of Polymer Additive Manufacturing Technologies You are ...

  5. Additive Manufacturing for Ceramics (Technical Report) | SciTech...

    Office of Scientific and Technical Information (OSTI)

    Additive Manufacturing for Ceramics Citation Details In-Document Search Title: Additive Manufacturing for Ceramics You are accessing a document from the Department of Energy's ...

  6. Energy Department Authorizes Additional Volume at Proposed Freeport...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Additional Volume at Proposed Freeport LNG Facility to Export Liquefied Natural Gas Energy Department Authorizes Additional Volume at Proposed Freeport LNG Facility to Export ...

  7. An Overview of Polymer Additive Manufacturing Technologies Peterson...

    Office of Scientific and Technical Information (OSTI)

    of Polymer Additive Manufacturing Technologies Peterson, Dominic S. Los Alamos National Laboratory Los Alamos National Laboratory Materials Science(36) Additive Manufacturing...

  8. Perfluoro Aryl Boronic Esters as Chemical Shuttle Additives ...

    Broader source: Energy.gov (indexed) [DOE]

    es107hunt2011p.pdf More Documents & Publications Develop & Evaluate Materials & Additives that Enhance Thermal & Overcharge Abuse Develop & evaluate materials & additives that ...

  9. Additives and Cathode Materials for High-Energy Lithium Sulfur...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Additives and Cathode Materials for High-Energy Lithium Sulfur Batteries Additives and Cathode Materials for High-Energy Lithium Sulfur Batteries 2013 DOE Hydrogen and Fuel Cells...

  10. Novel electrolytes and electrolyte additives for PHEV applications...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Novel electrolytes and electrolyte additives for PHEV applications 2009 DOE Hydrogen ... More Documents & Publications Novel Electrolytes and Additives Novel Electrolytes and ...

  11. Ionic Liquids as Novel Engine Lubricants or Lubricant Additives...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Engine Lubricants or Lubricant Additives Ionic Liquids as Novel Engine Lubricants or Lubricant Additives Bench test results showed that compared with fully-formulated engine oils, ...

  12. Energy Department Seeks Additional Feedback on Draft Guidance...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Additional Feedback on Draft Guidance for the Hydroelectric Production Incentive Program Energy Department Seeks Additional Feedback on Draft Guidance for the Hydroelectric ...

  13. Large-Scale Manufacturing of Nanoparticle-Based Lubrication Additives...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Large-Scale Manufacturing of Nanoparticle-Based Lubrication Additives Large-Scale Manufacturing of Nanoparticle-Based Lubrication Additives PDF icon nanoparticulate-basedlubricati...

  14. Department of Energy Announces Two Additional Loans of Oil from...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Additional Loans of Oil from the Strategic Petroleum Reserve Department of Energy Announces Two Additional Loans of Oil from the Strategic Petroleum Reserve September 2, 2005 - ...

  15. Unlocking the Potential of Additive Manufacturing in the Fuel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Unlocking the Potential of Additive Manufacturing in the Fuel Cells Industry Unlocking the Potential of Additive Manufacturing in the Fuel Cells Industry Download presentation...

  16. The Importance of Carbon Fiber to Polymer Additive Manufacturing...

    Office of Scientific and Technical Information (OSTI)

    The Importance of Carbon Fiber to Polymer Additive Manufacturing Citation Details In-Document Search Title: The Importance of Carbon Fiber to Polymer Additive Manufacturing...

  17. Recommendation 222: Recommendations on Additional Off-site Groundwater...

    Office of Environmental Management (EM)

    2: Recommendations on Additional Off-site Groundwater Migration Studies Recommendation 222: Recommendations on Additional Off-site Groundwater Migration Studies ORSSAB recommends...

  18. Reducing uncertainty in geostatistical description with well testing pressure data

    SciTech Connect (OSTI)

    Reynolds, A.C.; He, Nanqun; Oliver, D.S.

    1997-08-01

    Geostatistics has proven to be an effective tool for generating realizations of reservoir properties conditioned to static data, e.g., core and log data and geologic knowledge. Due to the lack of closely spaced data in the lateral directions, there will be significant variability in reservoir descriptions generated by geostatistical simulation, i.e., significant uncertainty in the reservoir descriptions. In past work, we have presented procedures based on inverse problem theory for generating reservoir descriptions (rock property fields) conditioned to pressure data and geostatistical information represented as prior means for log-permeability and porosity and variograms. Although we have shown that the incorporation of pressure data reduces the uncertainty below the level contained in the geostatistical model based only on static information (the prior model), our previous results assumed did not explicitly account for uncertainties in the prior means and the parameters defining the variogram model. In this work, we investigate how pressure data can help detect errors in the prior means. If errors in the prior means are large and are not taken into account, realizations conditioned to pressure data represent incorrect samples of the a posteriori probability density function for the rock property fields, whereas, if the uncertainty in the prior mean is incorporated properly into the model, one obtains realistic realizations of the rock property fields.

  19. TITLE AUTHORS SUBJECT SUBJECT RELATED DESCRIPTION PUBLISHER AVAILABILI...

    Office of Scientific and Technical Information (OSTI)

    OXYGEN REDUCTION SOLUBILITY SULFONIC ACIDS ADDITIVES CHEMICAL REACTION KINETICS ELECTRIC CONDUCTIVITY OPTIMIZATION PROGRESS REPORT CHEMICAL REACTIONS DIRECT ENERGY...

  20. Texas Liquefied Natural Gas Additions to and Withdrawals from Storage

    U.S. Energy Information Administration (EIA) Indexed Site

    2012 2013 2014 View History Net Withdrawals 0 2013-2013 Additions 0 * 0 2012

  1. Biomass 2014: Additional Speaker Biographies | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Additional Speaker Biographies Biomass 2014: Additional Speaker Biographies This document outlines the biographies of the additional speakers for Biomass 2014, held July 29-July 30 in Washington, D.C. PDF icon additional_speaker_biographies_biomass_2014 More Documents & Publications Bioenergy 2015 Speaker Biographies Demonstration and Deployment Workshop - Day 2 Sustainable Solutions to Global Energy Challenges

  2. System Advisor Model, SAM 2014.1.14: General Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    System Advisor Model, SAM 2014.1.14: General Description Nate Blair, Aron P. Dobos, Janine Freeman, Ty Neises, and Michael Wagner National Renewable Energy Laboratory Tom Ferguson, Paul Gilman, and Steven Janzou Independent Consultants Technical Report NREL/TP-6A20-61019 February 2014 NREL is a national laboratory of the U.S. Department of Energy Office of Energy Efficiency & Renewable Energy Operated by the Alliance for Sustainable Energy, LLC This report is available at no cost from the

  3. PBS ABB Title ABB Description/Scope ORP-0014

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Title ABB Description/Scope ORP-0014 242A Evaporator/222-S Laboratory * Operate and maintain the 242-A Evaporator * 222-S Safe and Compliant Operations * 222-S Facililty Reliability * 222-S Analytical Support/Equipment * 222-S Process Chemistry and Waste Handling ORP-0014 A/AX - Farm Retrieval Design, procurement, construction, readiness assessments, start-up, and operations of waste retrieval systems for 241-A and 241-AX Tank Farms. New systems will: 1) retrieve waste from 241-A and 241-AX

  4. Requirements Management System Browser (RMSB) software design description

    SciTech Connect (OSTI)

    Frank, D.D.

    1996-09-30

    The purpose of this document is to provide an ``as-built`` design description for the Requirements Management System Browser (RMSB) application. The Graphical User Interface (GUI) and database structure design are described for the RMSB application, referred to as the ``Browser.`` The RMSB application provides an easy to use PC-based interface to browse systems engineering data stored and managed in a UNIX software application. The system engineering data include functions, requirements, and architectures that make up the Tank Waste Remediation System (TWRS) technical baseline.

  5. 850/sup 0/C VHTR plant technical description

    SciTech Connect (OSTI)

    Not Available

    1980-06-01

    This report describes the conceptual design of an 842-MW(t) process heat very high temperature reactor (VHTR) plant having a core outlet temperature of 850/sup 0/C (1562/sup 0/F). The reactor is a variation of the high-temperature gas-cooled reactor (HTGR) power plant concept. The report includes a description of the nuclear heat source (NHS) and of the balance of reactor plant (BORP) requirements. The design of the associated chemical process plant is not covered in this report. The reactor design is similar to a previously reported VHTR design having a 950/sup 0/C (1742/sup 0/F) core outlet temperature.

  6. Advances in the ab initio description of nuclear three-cluster...

    Office of Scientific and Technical Information (OSTI)

    description of nuclear three-cluster systems Citation Details In-Document Search Title: Advances in the ab initio description of nuclear three-cluster systems Authors: Redondo, C R ...

  7. Electric Markets Technical Assistance Program: FY2002 Grant Descriptions and Contact Information

    Broader source: Energy.gov [DOE]

    Grant descriptions and contact information for grants awarded in FY 2002 under the Electric Markets Technical Assistance Program

  8. Descriptions of ESPC Task Order Schedules and Placement of Pricing Information (IDIQ Attachment J-5)

    Office of Energy Efficiency and Renewable Energy (EERE)

    Document provides task order schedule descriptions and information on the placement of pricing for energy savings performance contracts (ESPCs).

  9. Electric Markets Technical Assistance Program: FY2003 Grant Descriptions and Contact Information

    Broader source: Energy.gov [DOE]

    Grant descriptions and contact information for grants awarded during FY2003 under the Electric Markets Technical Assistance Program

  10. Electric Markets Technical Assistance Program: FY2001 Grant Descriptions and Contact Information

    Broader source: Energy.gov [DOE]

    Grant descriptions and contact information for grants awarded under the Electric Markets Technical Assistance Program in FY 2001.

  11. TITLE AUTHORS SUBJECT SUBJECT RELATED DESCRIPTION PUBLISHER AVAILABILI...

    Office of Scientific and Technical Information (OSTI)

    sponsored by the U S Department of Energy DOE and dedicated to the advancement of clean coal technology In addition to the development of high efficiency coal gasification...

  12. TITLE AUTHORS SUBJECT SUBJECT RELATED DESCRIPTION PUBLISHER AVAILABILI...

    Office of Scientific and Technical Information (OSTI)

    Additive Manufacturing for Ceramics Peterson Dominic S Los Alamos National Laboratory Los Alamos National Laboratory Materials Science d printing d printing...

  13. TITLE AUTHORS SUBJECT SUBJECT RELATED DESCRIPTION PUBLISHER AVAILABILI...

    Office of Scientific and Technical Information (OSTI)

    Thermographic In Situ Process Monitoring of the Electron Beam Melting Technology used in Additive Manufacturing Dinwiddie Ralph Barton ORNL ORNL Dehoff Ryan R ORNL ORNL Lloyd Peter...

  14. TITLE AUTHORS SUBJECT SUBJECT RELATED DESCRIPTION PUBLISHER AVAILABILI...

    Office of Scientific and Technical Information (OSTI)

    Thermal Properties and Beam Particle Interaction at Meso Scale during Electron Beam Additive Manufacturing Chen Jian ORNL ORNL Zheng Lili ORNL ORNL Feng Zhili ORNL ORNL Zhang...

  15. TITLE AUTHORS SUBJECT SUBJECT RELATED DESCRIPTION PUBLISHER AVAILABILI...

    Office of Scientific and Technical Information (OSTI)

    addition to other significant changes Although we have had very limited access to the machine and therefore are not presenting definitive performance results we can share some...

  16. TITLE AUTHORS SUBJECT SUBJECT RELATED DESCRIPTION PUBLISHER AVAILABILI...

    Office of Scientific and Technical Information (OSTI)

    distillation for new plants A design concept for a modular microchannel distillation unit was developed in Task In Task Ultrasonic Additive Machining UAM was evaluated as a...

  17. Unified description of superconducting pairing symmetry in electron...

    Office of Scientific and Technical Information (OSTI)

    Additional Journal Information: Journal Volume: 91; Journal Issue: 22; Journal ID: ISSN 1098-0121 Publisher: American Physical Society Sponsoring Org: USDOE Office of Science (SC), ...

  18. Electric energy supply systems: description of available technologies

    SciTech Connect (OSTI)

    Eisenhauer, J.L.; Rogers, E.A.; King, J.C.; Stegen, G.E.; Dowis, W.J.

    1985-02-01

    When comparing coal transportation with electric transmission as a means of delivering electric power, it is desirable to compare entire energy systems rather than just the transportation/transmission components because the requirements of each option may affect the requirements of other energy system components. PNL's assessment consists of two parts. The first part, which is the subject of this document, is a detailed description of the technical, cost, resource and environmental characteristics of each system component and technologies available for these components. The second part is a computer-based model that PNL has developed to simulate construction and operation of alternative system configurations and to compare the performance of these systems under a variety of economic and technical conditions. This document consists of six chapters and two appendices. A more thorough description of coal-based electric energy systems is presented in the Introduction and Chapter 1. Each of the subsequent chapters describes technologies for five system components: Western coal resources (Chapter 2), coal transportation (Chapter 3), coal gasification and gas transmission (Chapter 4), and electric power transmission (Chapter 6).

  19. Thermodynamical description of stationary, asymptotically flat solutions with conical singularities

    SciTech Connect (OSTI)

    Herdeiro, Carlos; Rebelo, Carmen; Radu, Eugen

    2010-05-15

    We examine the thermodynamical properties of a number of asymptotically flat, stationary (but not static) solutions having conical singularities, with both connected and nonconnected event horizons, using the thermodynamical description recently proposed in [C. Herdeiro, B. Kleihaus, J. Kunz, and E. Radu, Phys. Rev. D 81, 064013 (2010).]. The examples considered are the double-Kerr solution, the black ring rotating in either S{sup 2} or S{sup 1}, and the black Saturn, where the balance condition is not imposed for the latter two solutions. We show that not only the Bekenstein-Hawking area law is recovered from the thermodynamical description, but also the thermodynamical angular momentum is the Arnowitt-Deser-Misner angular momentum. We also analyze the thermodynamical stability and show that, for all these solutions, either the isothermal moment of inertia or the specific heat at constant angular momentum is negative, at any point in parameter space. Therefore, all these solutions are thermodynamically unstable in the grand canonical ensemble.

  20. Focused Crawling of the Deep Web Using Service Class Descriptions

    SciTech Connect (OSTI)

    Rocco, D; Liu, L; Critchlow, T

    2004-06-21

    Dynamic Web data sources--sometimes known collectively as the Deep Web--increase the utility of the Web by providing intuitive access to data repositories anywhere that Web access is available. Deep Web services provide access to real-time information, like entertainment event listings, or present a Web interface to large databases or other data repositories. Recent studies suggest that the size and growth rate of the dynamic Web greatly exceed that of the static Web, yet dynamic content is often ignored by existing search engine indexers owing to the technical challenges that arise when attempting to search the Deep Web. To address these challenges, we present DynaBot, a service-centric crawler for discovering and clustering Deep Web sources offering dynamic content. DynaBot has three unique characteristics. First, DynaBot utilizes a service class model of the Web implemented through the construction of service class descriptions (SCDs). Second, DynaBot employs a modular, self-tuning system architecture for focused crawling of the DeepWeb using service class descriptions. Third, DynaBot incorporates methods and algorithms for efficient probing of the Deep Web and for discovering and clustering Deep Web sources and services through SCD-based service matching analysis. Our experimental results demonstrate the effectiveness of the service class discovery, probing, and matching algorithms and suggest techniques for efficiently managing service discovery in the face of the immense scale of the Deep Web.

  1. Emergence of robust gaps in two-dimensional antiferromagnets via additional spin-1/2 probes

    SciTech Connect (OSTI)

    Ferreira, Aires; Lopes, J. Viana; Lopes dos Santos, J. M. B.

    2010-08-15

    We study the capacity of antiferromagnetic lattices of varying geometries to entangle two additional spin-1/2 probes. Analytical modeling of the quantum Monte Carlo data shows the appearance of a robust gap, allowing a description of entanglement in terms of probe-only states, even in cases where the coupling to the probes is larger than the gap of the spin lattice and cannot be treated perturbatively. We find a considerable enhancement of the temperature at which probe entanglement disappears as we vary the geometry of the bus and the coupling to the probes. In particular, the square Heisenberg antiferromagnet exhibits the best thermal robustness of all systems, whereas the three-leg ladder chain shows the best performance in the natural quantum ground state.

  2. Upcoming Webinar February 11: Additive Manufacturing for Fuel Cells

    Broader source: Energy.gov [DOE]

    On Tuesday, February 11, the Energy Department will present a live webinar on additive manufacturing to stimulate discussion in the hydrogen and fuel cell community on the application of additive manufacturing to prototyping and production.

  3. EERE Success Story - Novel Engine Lubrication Anti-Wear Additives

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Demonstrate Improved Fuel Economy | Department of Energy Story - Novel Engine Lubrication Anti-Wear Additives Demonstrate Improved Fuel Economy EERE Success Story - Novel Engine Lubrication Anti-Wear Additives Demonstrate Improved Fuel Economy March 14, 2016 - 1:27pm Addthis EERE Success Story - Novel Engine Lubrication Anti-Wear Additives Demonstrate Improved Fuel Economy EERE Success Story - Novel Engine Lubrication Anti-Wear Additives Demonstrate Improved Fuel Economy EERE Success Story -

  4. Unlocking the Potential of Additive Manufacturing in the Fuel Cells

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Industry | Department of Energy Unlocking the Potential of Additive Manufacturing in the Fuel Cells Industry Unlocking the Potential of Additive Manufacturing in the Fuel Cells Industry Download presentation slides from the DOE Fuel Cell Technologies Office webinar "Additive Manufacturing for Fuel Cells" held on February 11, 2014. PDF icon Additive Manufacturing for Fuel Cells Webinar Slides More Documents & Publications QTR Webinar: Chapter 8 - Industry and Manufacturing AMO

  5. Webinar: Additive Manufacturing for Fuel Cells | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Additive Manufacturing for Fuel Cells Webinar: Additive Manufacturing for Fuel Cells Below is the text version of the webinar titled "Additive Manufacturing for Fuel Cells," originally presented on February 11, 2014. In addition to this text version of the audio, you can access the presentation slides. [Recording starts on slide 2, Question and Answer] Moderator: ...once those are posted to our website. For this webinar today everyone is on mute. So please submit your questions via the

  6. Large-Scale Manufacturing of Nanoparticle-Based Lubrication Additives

    Broader source: Energy.gov [DOE]

    Fact Sheet About Development of Boron-Based Nanolubrication Additives for Improved Energy Efficiency and Reduced Emissions

  7. EIS-0386: Notice of Additional Public Hearing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    6: Notice of Additional Public Hearing EIS-0386: Notice of Additional Public Hearing Designation of Energy Corridors on Federal Land in the 11 Western States Additional Public Hearing on the Draft Programmatic Environmental Impact Statement; Designation of Energy Corridors on Federal Land in the 11 Western States PDF icon Additional Public Hearing on the Draft Programmatic Environmental Impact Statement; Designation of Energy Corridors on Federal Land in the 11 Western States, DOE/EIS-0386

  8. Magellan additional information | U.S. DOE Office of Science...

    Office of Science (SC) Website

    Miscellaneous ASCR Recovery Act Projects Magellan additional information Advanced Scientific Computing Research (ASCR) ASCR Home About Research Facilities Science Highlights ...

  9. Geometry Description Markup Language for Physics Simulation And Analysis Applications.

    SciTech Connect (OSTI)

    Chytracek, R.; McCormick, J.; Pokorski, W.; Santin, G.; /European Space Agency

    2007-01-23

    The Geometry Description Markup Language (GDML) is a specialized XML-based language designed as an application-independent persistent format for describing the geometries of detectors associated with physics measurements. It serves to implement ''geometry trees'' which correspond to the hierarchy of volumes a detector geometry can be composed of, and to allow to identify the position of individual solids, as well as to describe the materials they are made of. Being pure XML, GDML can be universally used, and in particular it can be considered as the format for interchanging geometries among different applications. In this paper we will present the current status of the development of GDML. After having discussed the contents of the latest GDML schema, which is the basic definition of the format, we will concentrate on the GDML processors. We will present the latest implementation of the GDML ''writers'' as well as ''readers'' for either Geant4 [2], [3] or ROOT [4], [10].

  10. Use of seismic attributes in geological description of carbonate rocks

    SciTech Connect (OSTI)

    Castrejon-Vacio, F.; Porres-Luna, A.A.

    1994-12-31

    Seismic attributes have been used widely in order to obtain geological description of petroleum reservoirs, especially as a support for the definition of horizontal continuity of strata, with special emphasis on terrigeneous formations. Nevertheless the application of seismic attributes to the study of carbonate and naturally fractured reservoirs has been limited. This paper shows the application of seismic attributes and seismic inversion to the geological and petrophysical characterization of a naturally fractured reservoir with complex lithology, which is characteristic of the most important producing formations in Mexico. The results from these techniques provide the basis for the definition of a realistic geological model, which is of prime concern for the reservoir`s characterization, numerical studies and EOR applications.

  11. Description of the Portsmouth Gas Centrifuge Enrichment Plant

    SciTech Connect (OSTI)

    Arthur, W.B.

    1980-12-16

    The Portsmouth Gas Centrifuge Enrichment Plant (GCEP) will be located at the site of the Portsmouth Gaseous Diffusion Plant in Piketon, Ohio. The purpose of the facility is to provide enriching services for the production of low assay enriched uranium for civilian nuclear power reactors. The construction and operation of the GCEP is administered by the US Department of Energy. The facility will be operated under contract from the US Government. Control of the GCEP rests solely with the US Government, which holds and controls access to the technology. Construction of GCEP is expected to be completed in the mid-1990's. Many facility design and operating procedures are subject to change. Nonetheless, the design described in this report does reflect current thinking. Descriptions of the general facility and major buildings such as the process buildings, feed and withdrawal building, cylinder storage and transfer, recycle/assembly building, and a summary of the centrifuge uranium enriching process are provided in this report.

  12. Microsoft PowerPoint - Omnibus PP-v10-combined-11-10-15v3

    Office of Environmental Management (EM)

    Renewable Energy | 1 NTER The National Training & Education Resource www.nterlearning.org * Dr. Michelle Fox * Alex Cohen Energy Efficiency & Renewable Energy | 2 * Identifying the problems in online learning * NTER overview * Innovative Features of NTER - Open Source - Distributed search - Interactive and immersive training - 3D in browser assessments - Authoring: empowering all to create and learn - Social reviews * NTER Demo * How to get involved * Future Development - Expert reviews

  13. TITLE AUTHORS SUBJECT SUBJECT RELATED DESCRIPTION PUBLISHER AVAILABILI...

    Office of Scientific and Technical Information (OSTI)

    The Use of Additive Manufacturing for Fabrication of Multi Function Small Satellite Structures Horais Brian J ORNL ORNL Love Lonnie J ORNL ORNL Dehoff Ryan R ORNL ORNL The use of...

  14. TITLE AUTHORS SUBJECT SUBJECT RELATED DESCRIPTION PUBLISHER AVAILABILI...

    Office of Scientific and Technical Information (OSTI)

    hindering cell wall degradability and the relevance of such approach for the bioethanol industry An additional interesting aspect of the work is that it showed that FAEA XYN2...

  15. The Importance of Carbon Fiber to Polymer Additive Manufacturing

    SciTech Connect (OSTI)

    Love, Lonnie J; Kunc, Vlastimil; Rios, Orlando; Duty, Chad E; Post, Brian K; Blue, Craig A

    2014-01-01

    Additive manufacturing holds tremendous promise in terms of revolutionizing manufacturing. However, fundamental hurdles limit mass adoption of the technology. First, production rates are extremely low. Second, the physical size of parts is generally small, less than a cubic foot. Third, while there is much excitement about metal additive manufacturing, the major growth area is in polymer additive manufacturing systems. Unfortunately, the mechanical properties of the polymer parts are poor, limiting the potential for direct part replacement. To address this issue, we describe three benefits of blending carbon fiber with polymer additive manufacturing. First, development of carbon fiber reinforced polymers for additive manufacturing achieves specific strengths approaching aerospace quality aluminum. Second, carbon fiber radically changes the behavior of the material during deposition, enabling large scale, out-of-the-oven, high deposition rate manufacturing. Finally, carbon fiber technology and additive manufacturing complement each other. Merging the two manufacturing processes enables the construction of complex components that would not be possible otherwise.

  16. Lab receives an additional $19 million for environmental cleanup

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Lab receives an additional $19 million for environmental cleanup Community Connections: Your link to news and opportunities from Los Alamos National Laboratory Latest Issue:May 2016 all issues All Issues » submit Lab receives an additional $19 million for environmental cleanup Lab also selects local businesses for five-year contracts June 1, 2013 Governor Susana Martinez visited the Lab in May to urge additional funding for cleanup Governor Susana Martinez visited the Lab in May to urge

  17. DOE Providing Additional Supercomputing Resources to Study Hurricane

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Effects on Gulf Coast | Department of Energy Providing Additional Supercomputing Resources to Study Hurricane Effects on Gulf Coast DOE Providing Additional Supercomputing Resources to Study Hurricane Effects on Gulf Coast July 19, 2006 - 3:36pm Addthis WASHINGTON, DC - The U.S. Department of Energy (DOE) announced today that the Office of Science has provided an additional 400,000 supercomputing processor-hours to the U.S. Army Corps of Engineers to simulate Gulf Coast hurricanes. The

  18. Detector Group Leader Accepts Additional Role as Lab's Chief Technology

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Officer | Jefferson Lab Detector Group Leader Accepts Additional Role as Lab's Chief Technology Officer Detector Group Leader Accepts Additional Role as Lab's Chief Technology Officer Drew Weisenberger Drew Weisenberger, who has led the Radiation Detector and Imaging Group at Jefferson Lab since 2008, recently accepted the additional role of Chief Technology Officer (CTO) for the lab. Andrew "Drew" Weisenberger, head of the Experimental Nuclear Physics Division's Radiation Detector

  19. Breaking Barriers in Polymer Additive Manufacturing (Conference) | SciTech

    Office of Scientific and Technical Information (OSTI)

    Connect Conference: Breaking Barriers in Polymer Additive Manufacturing Citation Details In-Document Search Title: Breaking Barriers in Polymer Additive Manufacturing Additive Manufacturing (AM) enables the creation of complex structures directly from a computer-aided design (CAD). There are limitations that prevent the technology from realizing its full potential. AM has been criticized for being slow and expensive with limited build size. Oak Ridge National Laboratory (ORNL) has developed

  20. Recommendation 222: Recommendations on Additional Off-site Groundwater

    Office of Environmental Management (EM)

    Migration Studies | Department of Energy 2: Recommendations on Additional Off-site Groundwater Migration Studies Recommendation 222: Recommendations on Additional Off-site Groundwater Migration Studies ORSSAB recommends that DOE proceed with an off-site groundwater quality assessment project and that DOE secure additional baseline funding for analysis to further understanding of potential migration and effects on off-site receptors. PDF icon Recommendation 222 PDF icon Response to

  1. Recommendation 223: Recommendations on Additional Waste Disposal Capacity |

    Office of Environmental Management (EM)

    Department of Energy 3: Recommendations on Additional Waste Disposal Capacity Recommendation 223: Recommendations on Additional Waste Disposal Capacity ORSSAB's recommendations encourage DOE to continue planning for an additional on-site disposal facility for low-level waste and that a second facility be placed in an area already used for similar waste disposal. PDF icon Recommendation 223 PDF icon Response to Recommendation 223 More Documents & Publications ORSSAB Meeting - February

  2. South Dakota Liquefied Natural Gas Additions to and Withdrawals from

    U.S. Energy Information Administration (EIA) Indexed Site

    Storage 1984-1998 Additions 0 0 0 0 0 0 1984-2014 Withdrawals 0 0 0 0 0 0 1984

  3. Texas Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 2010's 0 0 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date: 5/31/2016 Referring Pages: Additions of Liquefied Natural Gas into Storage Texas Liquefied Natural Gas Additions to and Withdrawals from Storage Additions of Liquefied Natural Gas into

  4. Wisconsin Liquefied Natural Gas Additions to and Withdrawals from Storage

    U.S. Energy Information Administration (EIA) Indexed Site

    -18 -29 20 -67 13 58 1980-2014 Additions 80 63 107 33 103 196 1980-2014 Withdrawals 98 92 87 100 89 138

  5. Friction Stir Additive Manufacturing for High Structural Performance...

    Energy Savers [EERE]

    of other potential applications for aerospace & energy industries Laser-FSAM hybrid & mini-sample testing capabilites 2 3 Chronological evolution of metal based additive...

  6. Measurement of $\\mathrm{ t \\bar{t} } $ production with additional...

    Office of Scientific and Technical Information (OSTI)

    mathrm t bart production with additional jet activity, including b quark jets, in the dilepton decay channel using pp collisions at sqrts 8 TeV Citation Details...

  7. ,"New Hampshire Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","New Hampshire Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  8. ,"New Jersey Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","New Jersey Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  9. ,"New York Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","New York Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  10. ,"North Carolina Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","North Carolina Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  11. ,"Rhode Island Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","Rhode Island Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  12. ,"South Carolina Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Of Series","Frequency","Latest Data for" ,"Data 1","South Carolina Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ,"Release Date:","9302015" ,"Next Release...

  13. Nevada Liquefied Natural Gas Additions to and Withdrawals from...

    U.S. Energy Information Administration (EIA) Indexed Site

    -76 -69 -42 -63 -57 16 1982-2014 Additions 106 125 112 82 153 227 1982-2014 Withdrawals 182 195 154 146 210 211 1982...

  14. Oregon Liquefied Natural Gas Additions to and Withdrawals from...

    U.S. Energy Information Administration (EIA) Indexed Site

    47 -53 -25 -16 -50 111 1980-2014 Additions 683 343 336 299 276 822 1980-2014 Withdrawals 436 396 361 315 326 711...

  15. Nebraska Liquefied Natural Gas Additions to and Withdrawals from...

    U.S. Energy Information Administration (EIA) Indexed Site

    -10 39 -73 -140 280 -202 1980-2014 Additions 165 346 147 1 407 481 1980-2014 Withdrawals 175 308 220 141 128 68...

  16. Arkansas Liquefied Natural Gas Additions to and Withdrawals from Storage

    U.S. Energy Information Administration (EIA) Indexed Site

    24 2 -7 9 12 14 1980-2014 Additions 27 42 47 57 52 56 1980-2014 Withdrawals 51 40 53 48 40 4

  17. California Liquefied Natural Gas Additions to and Withdrawals from Storage

    U.S. Energy Information Administration (EIA) Indexed Site

    5 2 7 -5 3 1 1980-2014 Additions 41 56 73 31 95 83 1980-2014 Withdrawals 46 54 66 36 92 8

  18. Delaware Liquefied Natural Gas Additions to and Withdrawals from Storage

    U.S. Energy Information Administration (EIA) Indexed Site

    3 -2 -31 51 -68 29 1980-2014 Additions 121 73 64 117 63 157 1980-2014 Withdrawals 118 76 96 66 131 128

  19. Illinois Liquefied Natural Gas Additions to and Withdrawals from Storage

    U.S. Energy Information Administration (EIA) Indexed Site

    260 74 127 419 -322 -442 1980-2014 Additions 465 398 657 750 40 61 1980-2014 Withdrawals 726 325 530 331 362 503

  20. Resonator for Coherent Addition of Semiconductor Laser Arrays...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Return to Search Resonator for Coherent Addition of Semiconductor Laser Arrays and Applications for a Solar Pumped Laser Array Oak Ridge National Laboratory Contact ORNL About This ...

  1. Correlations Between Metallic Lubricant Additive Species in the...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Dependence on Crankcase Oil Properties Correlations Between Metallic Lubricant Additive Species in the Ring Pack and Ash Emissions and Their Dependence on Crankcase Oil Properties ...

  2. Maine Liquefied Natural Gas Additions to and Withdrawals from...

    U.S. Energy Information Administration (EIA) Indexed Site

    -33 -25 -18 2 1 4 1981-2014 Additions 0 0 0 36 46 39 1981-2014 Withdrawals 33 25 18 34 45 35 1981...

  3. Idaho Liquefied Natural Gas Additions to and Withdrawals from...

    U.S. Energy Information Administration (EIA) Indexed Site

    387 70 -19 139 -259 -676 1981-2014 Additions 528 142 146 211 13 64 1981-2014 Withdrawals 141 72 166 73 271 740 1981

  4. NMAC 17.5.440 Extensions, Improvements, Additions, and Cooperative...

    Open Energy Info (EERE)

    5.440 Extensions, Improvements, Additions, and Cooperative Agreements between or among Utilities Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document-...

  5. Meso-Scale during Electron Beam Additive Manufacturing Chen,...

    Office of Scientific and Technical Information (OSTI)

    Thermal Properties and Beam-Particle Interaction at Meso-Scale during Electron Beam Additive Manufacturing Chen, Jian ORNL ORNL; Zheng, Lili ORNL ORNL; Feng, Zhili...

  6. Additive Manufacturing for Ceramics Peterson, Dominic S. [Los...

    Office of Scientific and Technical Information (OSTI)

    Additive Manufacturing for Ceramics Peterson, Dominic S. Los Alamos National Laboratory Los Alamos National Laboratory Materials Science(36) 3d printing 3d printing Abstract...

  7. Low Cost Injection Mold Creation via Hybrid Additive and Conventional...

    Office of Scientific and Technical Information (OSTI)

    Low Cost Injection Mold Creation via Hybrid Additive and Conventional Manufacturing Citation Details ... reduce the cost of the tooling (machining and materials) required to create ...

  8. Ionic Liquids as Multifunctional Ashless Additives for Engine...

    Broader source: Energy.gov (indexed) [DOE]

    A group of oil-miscible ionic liquids has been developed by an ORNL-GM team as candidate lubricant additives with promising physicalchemical properties and potential multiple ...

  9. DOE Announces Additional Steps in Developing Sustainable Biofuels...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    in Developing Sustainable Biofuels Industry DOE Announces Additional Steps in Developing Sustainable Biofuels Industry October 7, 2008 - 4:14pm Addthis Releases Results from...

  10. Louisiana Liquefied Natural Gas Additions to and Withdrawals from Storage

    U.S. Energy Information Administration (EIA) Indexed Site

    0 0 -24 1980-2014 Additions 0 0 0 0 0 0 1980-2014 Withdrawals 0 0 0 0 0 24

  11. Missouri Liquefied Natural Gas Additions to and Withdrawals from Storage

    U.S. Energy Information Administration (EIA) Indexed Site

    0 0 1980-2014 Additions 0 0 0 0 0 0 1980-2014 Withdrawals 0 0 0 0 0 0

  12. New Hampshire Liquefied Natural Gas Additions to and Withdrawals from

    U.S. Energy Information Administration (EIA) Indexed Site

    Storage 9 -3 4 -6 -0 1973-2013 Additions 82 33 112 65 124 185 1980-2014 Withdrawals 73 35 108 71 124 185

  13. Department of Energy Announces Plans for Additional Comment Period...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    prior to DOE issuing any National Corridor designations. Media contact(s): Craig Stevens, (202) 586-4940 Addthis Related Articles DOE Announces Additional Public Comment...

  14. Characteristics and Effects of Lubricant Additive Chemistry and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Service Life and Vehicle Fuel Economy Characteristics and Effects of Lubricant Additive Chemistry and Exhaust Conditions on Diesel Particulate Filter Service Life and Vehicle ...

  15. Alaska Liquefied Natural Gas Additions to and Withdrawals from Storage

    U.S. Energy Information Administration (EIA) Indexed Site

    0 1969-2014 Additions 0 0 0 0 0 0 1969-2014 Withdrawals 0 0 0 0 0 0 1999

  16. Upcoming Webinar February 11: Additive Manufacturing for Fuel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    the hydrogen and fuel cell community on the application of additive manufacturing to prototyping and production. Presentations by Eaton and Nuvera will highlight Eaton's experience...

  17. Unlocking the Potential of Additive Manufacturing in the Fuel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fuel Cells" held on February 11, 2014. PDF icon Additive Manufacturing for Fuel Cells Webinar Slides More Documents & Publications QTR Webinar: Chapter 8 - Industry and ...

  18. Large-Scale Manufacturing of Nanoparticulate-Based Lubrication Additives

    SciTech Connect (OSTI)

    2009-06-01

    This factsheet describes a research project whose goal is to design, develop, manufacture, and scale up boron-based nanoparticulate lubrication additives.

  19. EIS-0489: Notice of Comment Period Extension and Additional Scoping...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    EIS-0489: Notice of Comment Period Extension and Additional Scoping Meetings Jordan Cove Liquefaction Project (Coos County, OR) and Pacific Connector Pipeline Project (Coos, ...

  20. Materials and Additive Manufacturing for Energy Efficiency in...

    Office of Scientific and Technical Information (OSTI)

    Technical Report: Materials and Additive Manufacturing for Energy Efficiency in Wind Turbine and Aircraft Industries Citation Details In-Document Search Title: Materials and ...

  1. RESIDUAL STRESSES IN ADDITIVELY MANUFACTURED INCONEL 718 ENGINE...

    Office of Scientific and Technical Information (OSTI)

    Title: RESIDUAL STRESSES IN ADDITIVELY MANUFACTURED INCONEL 718 ENGINE MOUNT Authors: Watkins, Thomas R 1 ; Cornwell, Paris A 1 ; Dehoff, Ryan R 1 ; Nangia, Vinod 2 ; ...

  2. Two petroleum additives deals stall on the consolidation trail

    SciTech Connect (OSTI)

    Kiesche, E.S.

    1992-04-22

    The consolidation of the lubricant and fuel additives market is turning out to be anything but a slick transition. Two deals have fallen through since the beginning of April. Ethyl Corp. (Richmond, VA) has discontinued negotiations for the acquisition of BP Chemicals` (London) Adibis petroleum additives business and Lubrizol`s (Wickliffe, OH) proposed purchase of Amoco Chemical`s petroleum additives business is stalled, and may be completely derailed by antitrust concerns. Meanwhile, a third petroleum additives business, the European joint venture between Amoco and Finzis being liquidated.

  3. Feasibility and testing of lighweight, energy efficient, additive...

    Office of Scientific and Technical Information (OSTI)

    pneumatic control valve Citation Details In-Document Search Title: Feasibility and testing of lighweight, energy efficient, additive manufactured pneumatic control valve ...

  4. Feasibility and testing of lighweight, energy efficient, additive...

    Office of Scientific and Technical Information (OSTI)

    pneumatic control valve Citation Details In-Document Search Title: Feasibility and testing of lighweight, energy efficient, additive manufactured pneumatic control valve You ...

  5. Test report - caustic addition system operability test procedure

    SciTech Connect (OSTI)

    Parazin, R.E.

    1995-10-13

    This Operability Test Report documents the test results of test procedure WHC-SD-WM-OTP-167 ``Caustic Addition System Operability Test Procedure``. The Objective of the test was to verify the operability of the 241-AN-107 Caustic Addition System. The objective of the test was met

  6. Anomaly Detection In Additively Manufactured Parts Using Laser Doppler Vibrometery

    SciTech Connect (OSTI)

    Hernandez, Carlos A.

    2015-09-29

    Additively manufactured parts are susceptible to non-uniform structure caused by the unique manufacturing process. This can lead to structural weakness or catastrophic failure. Using laser Doppler vibrometry and frequency response analysis, non-contact detection of anomalies in additively manufactured parts may be possible. Preliminary tests show promise for small scale detection, but more future work is necessary.

  7. Fundamental Statistical Descriptions of Plasma Turbulence in Magnetic Fields

    SciTech Connect (OSTI)

    John A. Krommes

    2001-02-16

    A pedagogical review of the historical development and current status (as of early 2000) of systematic statistical theories of plasma turbulence is undertaken. Emphasis is on conceptual foundations and methodology, not practical applications. Particular attention is paid to equations and formalism appropriate to strongly magnetized, fully ionized plasmas. Extensive reference to the literature on neutral-fluid turbulence is made, but the unique properties and problems of plasmas are emphasized throughout. Discussions are given of quasilinear theory, weak-turbulence theory, resonance-broadening theory, and the clump algorithm. Those are developed independently, then shown to be special cases of the direct-interaction approximation (DIA), which provides a central focus for the article. Various methods of renormalized perturbation theory are described, then unified with the aid of the generating-functional formalism of Martin, Siggia, and Rose. A general expression for the renormalized dielectric function is deduced and discussed in detail. Modern approaches such as decimation and PDF methods are described. Derivations of DIA-based Markovian closures are discussed. The eddy-damped quasinormal Markovian closure is shown to be nonrealizable in the presence of waves, and a new realizable Markovian closure is presented. The test-field model and a realizable modification thereof are also summarized. Numerical solutions of various closures for some plasma-physics paradigms are reviewed. The variational approach to bounds on transport is developed. Miscellaneous topics include Onsager symmetries for turbulence, the interpretation of entropy balances for both kinetic and fluid descriptions, self-organized criticality, statistical interactions between disparate scales, and the roles of both mean and random shear. Appendices are provided on Fourier transform conventions, dimensional and scaling analysis, the derivations of nonlinear gyrokinetic and gyrofluid equations, stochasticity criteria for quasilinear theory, formal aspects of resonance-broadening theory, Novikov's theorem, the treatment of weak inhomogeneity, the derivation of the Vlasov weak-turbulence wave kinetic equation from a fully renormalized description, some features of a code for solving the direct-interaction approximation and related Markovian closures, the details of the solution of the EDQNM closure for a solvable three-wave model, and the notation used in the article.

  8. Nevada Test Site Environmental Report 2008 Attachment A: Site Description

    SciTech Connect (OSTI)

    Cathy A. Wills

    2009-09-01

    This attachment expands on the general description of the Nevada Test Site (NTS) presented in the Introduction to the Nevada Test Site Environmental Report 2008 (National Security Technologies, LLC [NSTec], 2009a). Included are subsections that summarize the sites geological, hydrological, climatological, and ecological setting. The cultural resources of the NTS are also presented. The subsections are meant to aid the reader in understanding the complex physical and biological environment of the NTS. An adequate knowledge of the sites environment is necessary to assess the environmental impacts of new projects, design and implement environmental monitoring activities for current site operations, and assess the impacts of site operations on the public residing in the vicinity of the NTS. The NTS environment contributes to several key features of the site that afford protection to the inhabitants of adjacent areas from potential exposure to radioactivity or other contaminants resulting from NTS operations. These key features include the general remote location of the NTS, restricted access, extended wind transport times, the great depths to slow-moving groundwater, little or no surface water, and low population density. This attachment complements the annual summary of monitoring program activities and dose assessments presented in the main body of this report.

  9. Nevada Test Site Environmental Report 2009, Attachment A: Site Description

    SciTech Connect (OSTI)

    Cathy Wills, ed.

    2010-09-13

    This attachment expands on the general description of the Nevada Test Site (NTS) presented in the Introduction to the Nevada Test Site Environmental Report 2009. Included are subsections that summarize the sites geological, hydrological, climatological, and ecological setting. The cultural resources of the NTS are also presented. The subsections are meant to aid the reader in understanding the complex physical and biological environment of the NTS. An adequate knowledge of the sites environment is necessary to assess the environmental impacts of new projects, design and implement environmental monitoring activities for current site operations, and assess the impacts of site operations on the public residing in the vicinity of the NTS. The NTS environment contributes to several key features of the site that afford protection to the inhabitants of adjacent areas from potential exposure to radioactivity or other contaminants resulting from NTS operations. These key features include the general remote location of the NTS, restricted access, extended wind transport times, the great depths to slow-moving groundwater, little or no surface water, and low population density. This attachment complements the annual summary of monitoring program activities and dose assessments presented in the main body of this report.

  10. Nevada Test Site Environmental Report 2005, Attachment A - Site Description

    SciTech Connect (OSTI)

    Cathy A. Wills

    2006-10-01

    This appendix to the ''Nevada Test Site Environmental Report 2005'', dated October 2006 (DOE/NV/11718--1214; DOE/NV/25946--007) expands on the general description of the Nevada Test Site (NTS) presented in the Introduction. Included are subsections that summarize the site?s geological, hydrological, climatological, and ecological setting. The cultural resources of the NTS are also presented. The subsections are meant to aid the reader in understanding the complex physical and biological environment of the NTS. An adequate knowledge of the site's environment is necessary to assess the environmental impacts of new projects, design and implement environmental monitoring activities for current site operations, and assess the impacts of site operations on the public residing in the vicinity of the NTS. The NTS environment contributes to several key features of the site which afford protection to the inhabitants of adjacent areas from potential exposure to radioactivity or other contaminants resulting from NTS operations. These key features include the general remote location of the NTS, restricted access, extended wind transport times, the great depths to slow-moving groundwater, little or no surface water, and low population density. This appendix complements the annual summary of monitoring program activities and dose assessments presented in the main body of this report.

  11. Nevada Test Site Environmental Report 2007 Attachment A: Site Description

    SciTech Connect (OSTI)

    Cathy Wills

    2008-09-01

    This appendix expands on the general description of the Nevada Test Site (NTS) presented in the Introduction to the Nevada Test Site Environmental Report 2007 (U.S. Department of Energy [DOE], 2008). Included are subsections that summarize the site's geological, hydrological, climatological, and ecological setting. The cultural resources of the NTS are also presented. The subsections are meant to aid the reader in understanding the complex physical and biological environment of the NTS. An adequate knowledge of the site's environment is necessary to assess the environmental impacts of new projects, design and implement environmental monitoring activities for current site operations, and assess the impacts of site operations on the public residing in the vicinity of the NTS. The NTS environment contributes to several key features of the site which afford protection to the inhabitants of adjacent areas from potential exposure to radioactivity or other contaminants resulting from NTS operations. These key features include the general remote location of the NTS, restricted access, extended wind transport times, the great depths to slow-moving groundwater, little or no surface water, and low population density. This attachment complements the annual summary of monitoring program activities and dose assessments presented in the main body of this report.

  12. Environmental Compliance and Protection Program Description Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Bechtel Jacobs

    2009-02-26

    The objective of the Environmental Compliance and Protection (EC and P) Program Description (PD) is to establish minimum environmental compliance requirements and natural resources protection goals for the Bechtel Jacobs Company LLC (BJC) Oak Ridge Environmental Management Cleanup Contract (EMCC) Contract Number DE-AC05-98OR22700-M198. This PD establishes the work practices necessary to ensure protection of the environment during the performance of EMCC work activities on the US Department of Energy's (DOE's) Oak Ridge Reservation (ORR) in Oak Ridge, Tennessee, by BJC employees and subcontractor personnel. Both BJC and subcontractor personnel are required to implement this PD. A majority of the decontamination and demolition (D and D) activities and media (e.g., soil and groundwater) remediation response actions at DOE sites on the ORR are conducted under the authority of the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). CERCLA activities are governed by individual CERCLA decision documents (e.g., Record of Decision [ROD] or Action Memorandum) and according to requirements stated in the Federal Facility Agreement for the Oak Ridge Reservation (DOE 1992). Applicable or relevant and appropriate requirements (ARARs) for the selected remedy are the requirements for environmental remediation responses (e.g., removal actions and remedial actions) conducted under CERCLA.

  13. The effect of additives on lime dissolution rates. Final report

    SciTech Connect (OSTI)

    Khang, S.J.

    1996-07-31

    Based on the previous years` studies concerning the efficiency of SO{sub 2} removal by spray dryers with high sulfur coal flue gas, the work for year five included investigations of lime dissolution rates at different slaking conditions and with the effect of additives. The prominent additives that have significant effects on lime dissolution rates were tested with the mini pilot spray drying absorber to see their effects on spray drying desulfurization applications. The mechanisms of these additive effects along with the properties of hygroscopic additives have been discussed and incorporated into the spray drying desulfurization model ``SPRAYMOD-M.`` Slaking conditions are very important factors in producing high quality lime slurry in spray drying desulfurization processes. At optimal slaking conditions, the slaked lime particles are very fine (3-5{mu}m) and the slaked lime has high BET surface areas which are beneficial to the desulfurization. The slaked lime dissolution rate experiments in our study are designed to determine how much lime can dissolve in a unit time if the initial lime surface area is kept constant. The purpose of the dissolution rate study for different additives is to find those effective additives that can enhance lime dissolution rates and to investigate the mechanisms of the dissolution rate enhancement properties for these additives. The applications of these additives on spray drying desulfurization are to further verify the theory that dissolution rate is a rate limiting step in the whole spray drying desulfurization process as well as to test the feasibility of these additives on enhancing SO{sub 2} removal in spray dryers.

  14. Vacuum pyrolysis of waste tires with basic additives

    SciTech Connect (OSTI)

    Zhang Xinghua; Wang Tiejun Ma Longlong; Chang Jie

    2008-11-15

    Granules of waste tires were pyrolyzed under vacuum (3.5-10 kPa) conditions, and the effects of temperature and basic additives (Na{sub 2}CO{sub 3}, NaOH) on the properties of pyrolysis were thoroughly investigated. It was obvious that with or without basic additives, pyrolysis oil yield increased gradually to a maximum and subsequently decreased with a temperature increase from 450 deg. C to 600 deg. C, irrespective of the addition of basic additives to the reactor. The addition of NaOH facilitated pyrolysis dramatically, as a maximal pyrolysis oil yield of about 48 wt% was achieved at 550 deg. C without the addition of basic additives, while a maximal pyrolysis oil yield of about 50 wt% was achieved at 480 deg. C by adding 3 wt% (w/w, powder/waste tire granules) of NaOH powder. The composition analysis of pyrolytic naphtha (i.b.p. (initial boiling point) {approx}205 deg. C) distilled from pyrolysis oil showed that more dl-limonene was obtained with basic additives and the maximal content of dl-limonene in pyrolysis oil was 12.39 wt%, which is a valuable and widely-used fine chemical. However, no improvement in pyrolysis was observed with Na{sub 2}CO{sub 3} addition. Pyrolysis gas was mainly composed of H{sub 2}, CO, CH{sub 4}, CO{sub 2}, C{sub 2}H{sub 4} and C{sub 2}H{sub 6}. Pyrolytic char had a surface area comparable to commercial carbon black, but its proportion of ash (above 11.5 wt%) was much higher.

  15. South Dakota Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) South Dakota Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 0 0 0 0 0 0 1990's 0 0 24 0 0 0 0 0 44 83 2000's 70 89 0 0 0 0 0 0 0 0 2010's 0 0 0 0 0 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date: 5/31/2016 Referring Pages: Additions of Liquefied Natural Gas

  16. New Hampshire Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) New Hampshire Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 5 0 21 0 0 0 0 0 0 0 1990's 0 0 0 0 0 0 0 0 0 0 2000's 0 0 29 80 138 99 27 101 45 82 2010's 33 112 65 124 185 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date: 5/31/2016 Referring Pages: Additions of

  17. Missouri Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Missouri Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 0 7 26 29 57 21 28 58 0 0 1990's 0 0 0 0 0 0 0 0 0 0 2000's 0 0 0 0 0 0 0 0 0 0 2010's 0 0 0 0 0 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date: 5/31/2016 Referring Pages: Additions of Liquefied Natural

  18. Zinc halogen battery electrolyte composition with lead additive

    DOE Patents [OSTI]

    Henriksen, Gary L.

    1981-01-01

    This disclosure relates to a zinc halogen battery electrolyte composition containing an additive providing improved zinc-on-zinc recyclability. The improved electrolyte composition involves the use of a lead additive to inhibit undesirable irregular plating and reduce nodular or dendritic growth on the electrode surface. The lead-containing electrolyte composition of the present invention appears to influence not only the morphology of the base plate zinc, but also the morphology of the zinc-on-zinc replate. In addition, such lead-containing electrolyte compositions appear to reduce hydrogen formation.

  19. Alaska Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Alaska Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1960's 2,581 1980's 0 0 0 0 0 0 1990's 0 0 0 0 0 0 0 0 0 0 2000's 0 159 319 467 697 0 0 0 0 0 2010's 0 0 0 0 0 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date: 5/31/2016 Referring Pages: Additions of Liquefied

  20. New additive retards coke formation in ethylene furnace tubes

    SciTech Connect (OSTI)

    Not Available

    1994-05-09

    Adding relatively small amounts of a new additive to the feed stream of a steam cracker can inhibit coke formation on the metal surfaces of processing equipment and increase furnace run time. The additive comprises a variable mixture of four to six inorganic salts in aqueous solution. The components of the additive mixture can be varied, as needed, for processing heavy feed materials such as heavy naphtha and gas oil. The process was first tested at a Korean petrochemical plant and is now operating successfully at a commercial facility in Russia. The results of the Korean trial are presented here.

  1. Corn fiber hulls as a food additive or animal feed

    DOE Patents [OSTI]

    Abbas, Charles; Beery, Kyle E.; Cecava, Michael J.; Doane, Perry H.

    2010-12-21

    The present invention provides a novel animal feed or food additive that may be made from thermochemically hydrolyzed, solvent-extracted corn fiber hulls. The animal feed or food additive may be made, for instance, by thermochemically treating corn fiber hulls to hydrolyze and solubilize the hemicellulose and starch present in the corn fiber hulls to oligosaccharides. The residue may be extracted with a solvent to separate the oil from the corn fiber, leaving a solid residue that may be prepared, for instance by aggolmerating, and sold as a food additive or an animal feed.

  2. Metal-air cell with performance enhancing additive

    SciTech Connect (OSTI)

    Friesen, Cody A; Buttry, Daniel

    2015-11-10

    Systems and methods drawn to an electrochemical cell comprising a low temperature ionic liquid comprising positive ions and negative ions and a performance enhancing additive added to the low temperature ionic liquid. The additive dissolves in the ionic liquid to form cations, which are coordinated with one or more negative ions forming ion complexes. The electrochemical cell also includes an air electrode configured to absorb and reduce oxygen. The ion complexes improve oxygen reduction thermodynamics and/or kinetics relative to the ionic liquid without the additive.

  3. Shell model description of band structure in 48Cr

    SciTech Connect (OSTI)

    Vargas, Carlos E.; Velazquez, Victor M.

    2007-02-12

    The band structure for normal and abnormal parity bands in 48Cr are described using the m-scheme shell model. In addition to full fp-shell, two particles in the 1d3/2 orbital are allowed in order to describe intruder states. The interaction includes fp-, sd- and mixed matrix elements.

  4. Preliminary paper - Development of the Reference Design Description for a geologic repository

    SciTech Connect (OSTI)

    Daniel, Russell B.; Rindskopf, M. Sam

    1997-11-20

    This report describes the current Reference Design Description (RDD) design expectations for a potential geologic repository that could be located at Yucca Mountain in Nevada.

  5. 2009-01 "Improved Description of Data in the Next Environmental...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Data in the Next Environmental Surveillance Report" 2009-01 "Improved Description of Data in the Next Environmental Surveillance Report" The intent of this recommendation ...

  6. Two-fluid description of wave-particle interactions in strong...

    Office of Scientific and Technical Information (OSTI)

    Title: Two-fluid description of wave-particle interactions in strong Buneman turbulence To understand the nature of anomalous resistivity in magnetic reconnection, we investigate ...

  7. Rhode Island Liquefied Natural Gas Additions to and Withdrawals from

    U.S. Energy Information Administration (EIA) Indexed Site

    Storage 256 -230 -7 60 -21 -879 1980-2014 Additions 698 468 430 517 624 0 1980-2014 Withdrawals 954 698 436 457 645 879

  8. Virginia Liquefied Natural Gas Additions to and Withdrawals from Storage

    U.S. Energy Information Administration (EIA) Indexed Site

    81 -207 1,588 1,296 40 28 1980-2014 Additions 1,008 664 1,977 1,699 764 1,033 1980-2014 Withdrawals 927 871 389 402 724 1,005

  9. Improvements in floating point addition/subtraction operations

    DOE Patents [OSTI]

    Farmwald, P.M.

    1984-02-24

    Apparatus is described for decreasing the latency time associated with floating point addition and subtraction in a computer, using a novel bifurcated, pre-normalization/post-normalization approach that distinguishes between differences of floating point exponents.

  10. Ionic Liquids as Multifunctional Ashless Additives for Engine Lubrication

    Broader source: Energy.gov [DOE]

    A group of oil-miscible ionic liquids has been developed by an ORNL-GM team as candidate lubricant additives with promising physical/chemical properties and potential multiple functionalities.

  11. Alabama Liquefied Natural Gas Additions to and Withdrawals from...

    U.S. Energy Information Administration (EIA) Indexed Site

    178 -21 -75 -22 63 -206 1980-2014 Additions 1,676 946 754 562 822 1,664 1980-2014 Withdrawals 1,498 968 829 583 759 1,869...

  12. Maryland Liquefied Natural Gas Additions to and Withdrawals from...

    U.S. Energy Information Administration (EIA) Indexed Site

    4,488 -13 42 27 -5 41 1980-2014 Additions 4,859 366 394 386 461 604 1980-2014 Withdrawals 371 378 352 359 466 563...

  13. Connecticut Liquefied Natural Gas Additions to and Withdrawals from Storage

    U.S. Energy Information Administration (EIA) Indexed Site

    164 178 129 260 -68 -327 1980-2014 Additions 713 651 655 743 558 1,032 1980-2014 Withdrawals 549 473 526 484 626 1,359

  14. Indiana Liquefied Natural Gas Additions to and Withdrawals from Storage

    U.S. Energy Information Administration (EIA) Indexed Site

    590 835 -380 -977 -81 771 1980-2014 Additions 691 1,983 609 0 925 2,193 1980-2014 Withdrawals 1,281 1,148 989 977 1,005 1,422

  15. ,"U.S. Natural Gas LNG Storage Additions (MMcf)"

    U.S. Energy Information Administration (EIA) Indexed Site

    for" ,"Data 1","U.S. Natural Gas LNG Storage Additions (MMcf)",1,"Annual",2014 ...nghistna1330nus2a.htm" ,"Source:","Energy Information Administration" ,"For Help, ...

  16. Ionic Liquids as Multi-Functional Lubricant Additives to Enhance...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Vehicle Technologies Office Merit Review 2014: Ionic Liquids as Anti-Wear Additives for Next-Generation Low-Viscosity Fuel-Efficient Engine Lubricants Ionic Liquids as Novel Engine ...

  17. Porosity of additive manufacturing parts for process monitoring

    SciTech Connect (OSTI)

    Slotwinski, J. A.; Garboczi, E. J.

    2014-02-18

    Some metal additive manufacturing processes can produce parts with internal porosity, either intentionally (with careful selection of the process parameters) or unintentionally (if the process is not well-controlled.) Material porosity is undesirable for aerospace parts - since porosity could lead to premature failure - and desirable for some biomedical implants, since surface-breaking pores allow for better integration with biological tissue. Changes in a part's porosity during an additive manufacturing build may also be an indication of an undesired change in the process. We are developing an ultrasonic sensor for detecting changes in porosity in metal parts during fabrication on a metal powder bed fusion system, for use as a process monitor. This paper will describe our work to develop an ultrasonic-based sensor for monitoring part porosity during an additive build, including background theory, the development and detailed characterization of reference additive porosity samples, and a potential design for in-situ implementation.

  18. Out of bounds additive manufacturing (Journal Article) | SciTech...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: Out of bounds additive manufacturing Citation Details In-Document Search ... GrantContract Number: AC05-00OR22725 Type: Accepted Manuscript Journal Name: Advanced ...

  19. Energy Department Provides Additional Emergency Fuel Loan to...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Part of Hurricane Sandy and Nor'easter Recovery Energy Department Provides Additional Emergency Fuel Loan to Department of Defense as Part of Hurricane Sandy and Nor'easter ...

  20. Obama Administration Announces Additional $9,593,500 for Local...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    the District of Columbia Obama Administration Announces Additional 9,593,500 for Local Energy Efficiency Improvements in the District of Columbia March 26, 2009 - 12:00am Addthis...

  1. OAR 340-120 - Additional Siting and Permitting Requirements for...

    Open Energy Info (EERE)

    OAR 340-120 - Additional Siting and Permitting Requirements for Hazardous Waste and PCB Treatment and Disposal Facilities Jump to: navigation, search OpenEI Reference LibraryAdd to...

  2. Airport Road Addition, Texas: Energy Resources | Open Energy...

    Open Energy Info (EERE)

    Hide Map This article is a stub. You can help OpenEI by expanding it. Airport Road Addition is a census-designated place in Brooks County, Texas.1 References ...

  3. Determining if a change to a proposal requires additional NEPA documentation: the Smithsonian Solution

    SciTech Connect (OSTI)

    ECCLESTON, C.H.

    1999-02-23

    Proposed actions tend to evolve over time. Once National Environmental Policy Act (NEPA) documentation is completed, agencies are at risk that subsequent changes may not be adequately covered or that existing NEPA documentation maybe completely invalidated. Neither NEPA nor its subsequent regulations provide sufficient direction for determining the degree to which a proposed action may change before preparation of new or supplemental documentation is necessary. Yet, decisionmakers are routinely involved in determining if a change to a proposed action departs, to such an extent, from the description presented in the NEPA document that additional documentation is necessary. Experience demonstrates that no two decisionmakers will completely agree, one decisionmaker might believe that a particular change would not require additional documentation, while the other concludes the exact opposite. Lacking definitive direction, decisionmakers and critics alike may point to a universe of potential considerations as the basis for defending their claim that a change in an action does or does not require new or additional NEPA documentation. Assertions are often based on equivocal opinions that can be neither proved nor disproved. Moreover, decisionmakers are frequently placed in an arduous dilemma of justifying a decision, for which there is no generally accepted methodology on which to base the decision. Lack of definitive direction can prolong the decisionmaking process, resulting in project delays. This can also lead to inappropriate levels of NEPA documentation, inconsistencies in decisionmaking, and increased risk of a legal challenge because of insufficient documentation. Clearly, a more systematic and less subjective approach is needed, A tool for streamlining the NEPA process, by reducing this degree of subjectivity, is presented in this paper.

  4. Additive Manufacturing for Ceramics (Technical Report) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Additive Manufacturing for Ceramics Citation Details In-Document Search Title: Additive Manufacturing for Ceramics Authors: Peterson, Dominic S. [1] + Show Author Affiliations Los Alamos National Laboratory [Los Alamos National Laboratory Publication Date: 2014-01-29 OSTI Identifier: 1119593 Report Number(s): LA-UR-14-20523 DOE Contract Number: AC52-06NA25396 Resource Type: Technical Report Research Org: Los Alamos National Laboratory (LANL) Sponsoring Org: DOE/LANL Country of Publication:

  5. An Overview of Polymer Additive Manufacturing Technologies (Technical

    Office of Scientific and Technical Information (OSTI)

    Report) | SciTech Connect An Overview of Polymer Additive Manufacturing Technologies Citation Details In-Document Search Title: An Overview of Polymer Additive Manufacturing Technologies Authors: Peterson, Dominic S. [1] + Show Author Affiliations Los Alamos National Laboratory [Los Alamos National Laboratory Publication Date: 2014-01-29 OSTI Identifier: 1119594 Report Number(s): LA-UR-14-20527 DOE Contract Number: AC52-06NA25396 Resource Type: Technical Report Research Org: Los Alamos

  6. Evaluation of advanced polymers for additive manufacturing (Technical

    Office of Scientific and Technical Information (OSTI)

    Report) | SciTech Connect Technical Report: Evaluation of advanced polymers for additive manufacturing Citation Details In-Document Search Title: Evaluation of advanced polymers for additive manufacturing The goal of this Manufacturing Demonstration Facility (MDF) technical collaboration project between Oak Ridge National Laboratory (ORNL) and PPG Industries, Inc. was to evaluate the feasibility of using conventional coatings chemistry and technology to build up material layer-by-layer. The

  7. Feasibility and testing of lighweight, energy efficient, additive

    Office of Scientific and Technical Information (OSTI)

    manufactured pneumatic control valve (Technical Report) | SciTech Connect Feasibility and testing of lighweight, energy efficient, additive manufactured pneumatic control valve Citation Details In-Document Search Title: Feasibility and testing of lighweight, energy efficient, additive manufactured pneumatic control valve AeroValve s innovative pneumatic valve technology recycles compressed air through the valve body with each cycle of the valve, and was reported to reduce compressed air

  8. Low Cost Injection Mold Creation via Hybrid Additive and Conventional

    Office of Scientific and Technical Information (OSTI)

    Manufacturing (Technical Report) | SciTech Connect Low Cost Injection Mold Creation via Hybrid Additive and Conventional Manufacturing Citation Details In-Document Search Title: Low Cost Injection Mold Creation via Hybrid Additive and Conventional Manufacturing The purpose of the proposed project between Cummins and ORNL is to significantly reduce the cost of the tooling (machining and materials) required to create injection molds to make plastic components. Presently, the high cost of this

  9. Materials and Additive Manufacturing for Energy Efficiency in Wind Turbine

    Office of Scientific and Technical Information (OSTI)

    and Aircraft Industries (Technical Report) | SciTech Connect Technical Report: Materials and Additive Manufacturing for Energy Efficiency in Wind Turbine and Aircraft Industries Citation Details In-Document Search Title: Materials and Additive Manufacturing for Energy Efficiency in Wind Turbine and Aircraft Industries The purpose of this project was to develop surface treatments which will inhibit the formation of ice on turbine blades and propellers. ORNL worked with Piedmont Propulsion

  10. Cyanoethylated compounds as additives in lithium/lithium batteries

    DOE Patents [OSTI]

    Nagasubramanian, Ganesan

    1999-01-01

    The power loss of lithium/lithium ion battery cells is significantly reduced, especially at low temperatures, when about 1% by weight of an additive is incorporated in the electrolyte layer of the cells. The usable additives are organic solvent soluble cyanoethylated polysaccharides and poly(vinyl alcohol). The power loss decrease results primarily from the decrease in the charge transfer resistance at the interface between the electrolyte and the cathode.

  11. Additional Funding & Financing Resources | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Additional Funding & Financing Resources Additional Funding & Financing Resources Workers use a giant crane to lift the blade assembly on a wind turbine at NREL's National Wind Technology Center. | Photo by Dennis Schroeder. Workers use a giant crane to lift the blade assembly on a wind turbine at NREL's National Wind Technology Center. | Photo by Dennis Schroeder. Want to know more about funding and financing for energy projects and businesses? Check out general resources at the Energy

  12. Ionic Liquids as Novel Lubricants and /or Lubricant Additives

    SciTech Connect (OSTI)

    Qu, J.; Viola, M. B.

    2013-10-31

    This ORNL-GM CRADA developed ionic liquids (ILs) as novel lubricants or oil additives for engine lubrication. A new group of oil-miscible ILs have been designed and synthesized with high thermal stability, non-corrosiveness, excellent wettability, and most importantly effective anti-scuffing/anti-wear and friction reduction characteristics. Mechanistic analysis attributes the superior lubricating performance of IL additives to their physical and chemical interactions with metallic surfaces. Working with a leading lubricant formulation company, the team has successfully developed a prototype low-viscosity engine oil using a phosphonium-phosphate IL as an anti-wear additive. Tribological bench tests of the IL-additized formulated oil showed 20-33% lower friction in mixed and elastohydrodynamic lubrication and 38-92% lower wear in boundary lubrication when compared with commercial Mobil 1 and Mobil Clean 5W-30 engine oils. High-temperature, high load (HTHL) full-size engine tests confirmed the excellent anti-wear performance for the IL-additized engine oil. Sequence VID engine dynamometer tests demonstrated an improved fuel economy by >2% for this IL-additized engine oil benchmarked against the Mobil 1 5W-30 oil. In addition, accelerated catalyst aging tests suggest that the IL additive may potentially have less adverse impact on three-way catalysts compared to the conventional ZDDP. Follow-on research is needed for further development and optimization of IL chemistry and oil formulation to fully meet ILSAC GF-5 specifications and further enhance the automotive engine efficiency and durability.

  13. Additional Verification Bodies Now Available for SEP | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Additional Verification Bodies Now Available for SEP Additional Verification Bodies Now Available for SEP May 14, 2014 - 11:40am Addthis Superior Energy Performance (SEP) recognizes industrial facilities that demonstrate energy management excellence and sustained energy savings. Third-party verification using an ANSI-ANAB Accredited Verification Body offers robust, independent confirmation of a facility's conformance to ISO 50001 and improved energy performance-providing accurate energy numbers

  14. RESIDUAL STRESSES IN ADDITIVELY MANUFACTURED INCONEL 718 ENGINE MOUNT

    Office of Scientific and Technical Information (OSTI)

    (Conference) | SciTech Connect Conference: RESIDUAL STRESSES IN ADDITIVELY MANUFACTURED INCONEL 718 ENGINE MOUNT Citation Details In-Document Search Title: RESIDUAL STRESSES IN ADDITIVELY MANUFACTURED INCONEL 718 ENGINE MOUNT Authors: Watkins, Thomas R [1] ; Cornwell, Paris A [1] ; Dehoff, Ryan R [1] ; Nangia, Vinod [2] ; Godfrey, Donald G. [2] + Show Author Affiliations ORNL Honeywell Aerospace Services Publication Date: 2015-01-01 OSTI Identifier: 1224750 DOE Contract Number:

  15. Reducing nontemplated 3' nucleotide addition to polynucleotide transcripts

    DOE Patents [OSTI]

    Kao, C. Cheng

    2000-01-01

    Non-template 3' nucleotide addition to a transcript is reduced by transcribing a transcript from a template comprising an ultimate and/or penultimate 5' ribose having a C'2 substituent such as methoxy, which reduces non-template 3' nucleotide addition to the transcript. The methods are shown to be applicable to a wide variety of polymerases, including Taq, T7 RNA polymerase, etc.

  16. Deuterium separation by infrared-induced addition reaction

    DOE Patents [OSTI]

    Marling, John B.

    1977-01-01

    A method for deuterium enrichment by the infrared-induced addition reaction of a deuterium halide with an unsaturated aliphatic compound. A gaseous mixture of a hydrogen halide feedstock and an unsaturated aliphatic compound, particularly an olefin, is irradiated to selectively vibrationally excite the deuterium halide contained therein. The excited deuterium halide preferentially reacts with the unsaturated aliphatic compound to produce a deuterated addition product which is removed from the reaction mixture.

  17. Idaho Crews Use Waste Treatment Expertise to Land Additional Work |

    Office of Environmental Management (EM)

    Department of Energy Idaho Crews Use Waste Treatment Expertise to Land Additional Work Idaho Crews Use Waste Treatment Expertise to Land Additional Work March 31, 2016 - 12:20pm Addthis Ron Holm, a RWMC foreman, remotely monitors activities inside an enclosed area where a debris repackaging project is underway. Ron Holm, a RWMC foreman, remotely monitors activities inside an enclosed area where a debris repackaging project is underway. A large structural steel pan was one of several pans

  18. Energy Department Makes Additional $4 Billion in Loan Guarantees Available

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    for Innovative Renewable Energy and Efficient Energy Projects | Department of Energy Additional $4 Billion in Loan Guarantees Available for Innovative Renewable Energy and Efficient Energy Projects Energy Department Makes Additional $4 Billion in Loan Guarantees Available for Innovative Renewable Energy and Efficient Energy Projects July 3, 2014 - 10:20am Addthis News Media Contact (202)586-4940 Washington D.C. - In support of the President's Climate Action Plan, the Department of Energy

  19. Energy Department Seeks Additional Feedback on Draft Guidance for the

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Hydroelectric Production Incentive Program | Department of Energy Additional Feedback on Draft Guidance for the Hydroelectric Production Incentive Program Energy Department Seeks Additional Feedback on Draft Guidance for the Hydroelectric Production Incentive Program October 20, 2014 - 9:15am Addthis The Department of Energy (DOE) is currently inviting comments from the general public on revised guidance relating to the implementation of Section 242 of the Energy Policy Act of 2005, the

  20. Control of pyrite addition in coal liquefaction process

    DOE Patents [OSTI]

    Schmid, Bruce K. (Englewood, CO); Junkin, James E. (Englewood, CO)

    1982-12-21

    Pyrite addition to a coal liquefaction process (22, 26) is controlled (118) in inverse proportion to the calcium content of the feed coal to maximize the C.sub.5 --900.degree. F. (482.degree. C.) liquid yield per unit weight of pyrite added (110). The pyrite addition is controlled in this manner so as to minimize the amount of pyrite used and thus reduce pyrite contribution to the slurry pumping load and disposal problems connected with pyrite produced slag.

  1. Develop and Evaluate Materials and Additives that Enhance Thermal and

    Broader source: Energy.gov (indexed) [DOE]

    Overcharge Abuse | Department of Energy 2 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting PDF icon es035_chen_2012_o.pdf More Documents & Publications Develop & Evaluate Materials & Additives that Enhance Thermal & Overcharge Abuse Develop & Evaluate Materials & Additives that Enhance Thermal & Overcharge Abuse High Voltage Electrolyte for Lithium Batteries

  2. Experimental and Theoretical Investigation of Lubricant and Additive

    Broader source: Energy.gov (indexed) [DOE]

    Effects on Engine Friction | Department of Energy Combining data from motored engine friction, a theoretical engine model, a line friction contact rig, and a fired engine can provide better insight to lube oil and additive performance. PDF icon p-02_rohr.pdf More Documents & Publications Validation of a Small Engine Based Procedure for Studying Performance of Engine Lube Oils, Ionic Liquids as Lubricants and/or Lubricant Additives, Opportunities for Engine Friction Reduction and Durable

  3. Blast furnace coke quality in relation to petroleum coke addition

    SciTech Connect (OSTI)

    Alvarez, R.; Diez, M.A.; Menendez, J.A.; Barriocanal, C.; Pis, J.J.; Sirgado, M.

    1995-12-01

    The incorporation of petroleum coke as an additive in industrial coking coal blends is a practice often used by steel companies. A suitable blast furnace coke produced by replacing part of the coking coal blend with a suitable petroleum coke (addition of 5 to 15%), was made by Great Lakes Carbon Corporation and successfully tested at several blast furnaces. This coke had lower reactivity, less ash and slightly higher sulfur content than coke made without the addition of petroleum coke. In contrast with these results, it has been reported in a BCRA study that additions of petroleum coke to a strong coking coal, above 5 wt%, increased coke reactivity. These differences may be explained on the basis of the coal or blend characteristics to which petroleum coke is added. Petroleum coke addition seems to give better results if the coal/blend has high fluidity. The present situation in Spain is favorable for the use of petroleum coke. So, a study of laboratory and semi-industrial scale was made to assess the possibility of using petroleum coke as an additive to the typical industrial coal blend coked by the Spanish Steel Company, ENSIDESA. The influence of the petroleum coke particle size was also studied to semi-industrial scale.

  4. Validity of ELTB Equation for Suitable Description of BEC

    SciTech Connect (OSTI)

    Kim, Dooyoung; Kim, Jinguanghao; Yoon, Jin-Hee

    2005-10-17

    The Bose-Einstein condensation (BEC) has been found for various alkali-metal gases such as 7Li, 87Rb, Na, and H. For the description of atoms in this condensate state, the Gross-Pitaevskii (GP) equation has been widely used. However, the GP equation contains the nonlinear term, which makes this equation hard to solve. Therefore, physical quantities are usually obtained numerically, and sometimes it is difficult to extract a physical meaning from the calculated results. The nuclear theory group at Purdue University in the U.S. developed a new simple equation, the equivalent linear two-body (ELTB) equation, using the hyper-radius coordinates and tested it for one-dimensional BEC system. Their results are consistent with the numerical values from the GP equation within 4.5%.We test the validity of the ELTB equation for three-dimensional BEC system by calculating the energies per particle and the wave functions for 87Rb gas and for 7Li gas. We use the quantum-mechanical variational method for the BEC energy. Our result for 87Rb gas agrees with a numerical calculation based on the GP equation, with a relative error of 12% over a wide range of N from 100 to 10,000. The relative distances between particles for 7Li gas are consistent within a relative error of 17% for N {<=} 1300. The relatively simple form of the ELTB equation, compared with the GP equation, enables us to treat the N-body system easily and efficiently. We conclude that the ELTB equation is a powerful equation for describing BEC system because it is easy to treat.

  5. Functional description for the Worldwide Port System (WPS) Regional Integrated Cargo Database (ICDB)

    SciTech Connect (OSTI)

    Truett, L.F.; Rollow, J.P.; Shipe, P.C.; Faby, E.Z.; Fluker, J.; Hancock, W.R.; Grubb, J.W.; Russell, D.L.; Ferguson, R.A.

    1995-12-15

    This Functional Description for the Worldwide Port System (WPS) Regional Integrated Cargo Database (ICDB) documents the purpose of and requirements for the ICDB in order to ensure a mutual understanding between the development group and the user group of the system. This Functional Description defines ICDB and provides a clear statement of the initial operational capability to be developed.

  6. Computer software design description for the integrated control and data acquisition system LDUA system

    SciTech Connect (OSTI)

    Aftanas, B.L.

    1998-08-12

    This Computer Software Design Description (CSDD) document provides the overview of the software design for all the software that is part of the integrated control and data acquisition system of the Light Duty Utility Arm System (LDUA). It describes the major software components and how they interface. It also references the documents that contain the detailed design description of the components.

  7. Organogermanium Chemistry: Germacyclobutanes and digermane Additions to Acetylenes

    SciTech Connect (OSTI)

    Andrew Michael Chubb

    2003-12-12

    This dissertation comprises two main research projects. The first project, presented in Chapter 1, involves the synthesis and thermochemistry of germacyclobutanes (germetanes). Four new germetanes (spirodigermetane, diallylgermetane, dichlorogermetane, and germacyclobutane) have been synthesized using a modified di-Grignard synthesis. Diallylgermetane is shown to be a useful starting material for obtaining other germetanes, particularly the parent germetane, germacyclobutane. The gas-phase thermochemistries of spirodigermetane, diallylgermetane and germacyclobutane have been explored via pulsed stirred-flow reactor (SFR) studies, showing remarkable differences in decomposition, depending on the substitution at the germanium atom. The second project investigates the thermochemical, photochemical, and catalytic additions of several digermanes to acetylenes. The first examples of thermo- and photochemical additions of Ge-Ge bonds to C{triple_bond}C are demonstrated. Mechanistic investigations are described and comparisons are made to analogous disilane addition reactions, previously studied in their group.

  8. Reducing Communication in Algebraic Multigrid Using Additive Variants

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Vassilevski, Panayot S.; Yang, Ulrike Meier

    2014-02-12

    Algebraic multigrid (AMG) has proven to be an effective scalable solver on many high performance computers. However, its increasing communication complexity on coarser levels has shown to seriously impact its performance on computers with high communication cost. Moreover, additive AMG variants provide not only increased parallelism as well as decreased numbers of messages per cycle but also generally exhibit slower convergence. Here we present various new additive variants with convergence rates that are significantly improved compared to the classical additive algebraic multigrid method and investigate their potential for decreased communication, and improved communication-computation overlap, features that are essential for goodmore » performance on future exascale architectures.« less

  9. Rhode Island Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Rhode Island Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 61 265 243 47 97 147 20 65 174 164 1990's 142 749 796 462 1,156 857 850 1,056 102 162 2000's 174 72 254 1,290 971 850 390 1,093 656 698 2010's 468 430 517 624 0 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next

  10. Wisconsin Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Wisconsin Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 136 238 283 60 272 131 64 74 253 228 1990's 116 167 57 112 266 206 269 143 85 53 2000's 71 76 102 95 49 114 60 148 130 80 2010's 63 107 33 103 196 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date:

  11. Arkansas Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Arkansas Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 14 5 21 0 44 18 22 52 42 30 1990's 128 38 50 53 73 29 0 57 64 52 2000's 52 50 85 36 76 72 45 54 51 27 2010's 42 47 57 52 56 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date: 5/31/2016 Referring Pages:

  12. Delaware Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Delaware Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 113 99 118 94 149 133 0 6 93 39 1990's 88 79 61 99 225 103 237 112 77 83 2000's 182 88 127 219 230 138 68 215 122 121 2010's 73 64 117 63 157 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date: 5/31/2016

  13. Idaho Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Idaho Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 110 361 110 230 287 93 0 528 258 1990's 291 340 1,338 1,389 554 405 636 868 776 720 2000's 29 1,358 239 210 330 46 415 89 0 528 2010's 142 146 211 13 64 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date:

  14. Illinois Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Illinois Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 277 327 524 338 1,034 653 199 223 393 0 1990's 883 115 570 417 1,326 370 971 283 60 650 2000's 97 654 69 875 406 3 238 475 1 465 2010's 398 657 750 40 61 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date:

  15. Additive manufacturing method for SRF components of various geometries

    DOE Patents [OSTI]

    Rimmer, Robert; Frigola, Pedro E; Murokh, Alex Y

    2015-05-05

    An additive manufacturing method for forming nearly monolithic SRF niobium cavities and end group components of arbitrary shape with features such as optimized wall thickness and integral stiffeners, greatly reducing the cost and technical variability of conventional cavity construction. The additive manufacturing method for forming an SRF cavity, includes atomizing niobium to form a niobium powder, feeding the niobium powder into an electron beam melter under a vacuum, melting the niobium powder under a vacuum in the electron beam melter to form an SRF cavity; and polishing the inside surface of the SRF cavity.

  16. PROJECT PROFILE: Additively Manufactured Photovoltaic Inverter (SuNLaMP)

    Broader source: Energy.gov [DOE]

    Integrating hundreds of gigawatts of photovoltaic (PV) solar power onto our country’s electric grid requires transformative power conversion system designs that find a balance between performance, reliability, functionality and cost. The National Renewable Energy Laboratory (NREL) will lead this project to develop a unique PV inverter design that combines the latest wide bandgap high-voltage Silicon Carbide (SiC) semiconductor devices with new technologies, such as additive manufacturing and multi-objective magnetic design optimization. By developing an additively manufactured PV inverter (AMPVI), NREL researchers aim to significantly reduce the cost of PV power electronics.

  17. Oregon Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Oregon Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 251 265 28 649 304 461 0 183 803 940 1990's 754 609 376 1,137 860 790 693 889 757 540 2000's 997 1,234 594 977 1,193 1,733 1,078 613 1,315 683 2010's 343 336 299 276 822 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next

  18. Maine Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Maine Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 0 364 166 203 308 127 226 157 29 1990's 18 25 26 16 27 19 26 11 61 83 2000's 45 14 23 0 0 0 19 20 32 0 2010's 0 0 36 46 39 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date: 5/31/2016 Referring Pages:

  19. Nebraska Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Nebraska Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 225 119 7 283 65 4 81 130 299 210 1990's 493 92 283 287 393 115 915 505 0 377 2000's 288 598 187 601 449 185 303 214 159 165 2010's 346 147 1 407 481 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date:

  20. Nevada Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Nevada Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 294 241 133 419 217 441 213 696 1990's 356 767 83 253 241 259 180 276 92 206 2000's 153 211 181 193 199 587 316 202 174 106 2010's 125 112 82 153 227 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date:

  1. Alabama Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Alabama Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 655 908 754 353 838 512 581 465 607 512 1990's 893 511 501 612 944 524 979 960 501 564 2000's 729 504 871 655 509 493 704 868 1,003 1,676 2010's 946 754 562 822 1,664 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next

  2. Characteristics of yttrium oxide laser ceramics with additives

    SciTech Connect (OSTI)

    Osipov, V V; Solomonov, V I; Orlov, A N; Shitov, V A; Maksimov, R N; Spirina, A V

    2013-03-31

    Neodymium- or ytterbium-doped laser ceramics with a disordered crystal-field structure formed by introduction of iso- and heterovalent elements into yttrium oxide are studied. It is shown that these additives broaden the spectral band of laser transitions, which makes it possible to use ceramics as active laser media emitting ultrashort pulses. Lasing was obtained in several samples of this ceramics. At the same time, it is shown that addition of zirconium and hafnium stimulates the Foerster quenching of upper laser levels and pump levels. (extreme light fields and their applications)

  3. Energy Department Provides Additional Emergency Fuel Loan to Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Defense as Part of Hurricane Sandy and Nor'easter Recovery | Department of Energy Additional Emergency Fuel Loan to Department of Defense as Part of Hurricane Sandy and Nor'easter Recovery Energy Department Provides Additional Emergency Fuel Loan to Department of Defense as Part of Hurricane Sandy and Nor'easter Recovery November 9, 2012 - 7:15pm Addthis NEWS MEDIA CONTACT (202) 586-4940 WASHINGTON - As part of the government-wide response and recovery effort for Hurricane Sandy and the

  4. Contingency contractor optimization. phase 3, model description and formulation.

    SciTech Connect (OSTI)

    Gearhart, Jared Lee; Adair, Kristin Lynn; Jones, Katherine A.; Bandlow, Alisa; Detry, Richard Joseph; Durfee, Justin D.; Jones, Dean A.; Martin, Nathaniel; Nanco, Alan Stewart; Nozick, Linda Karen

    2013-06-01

    The goal of Phase 3 the OSD ATL Contingency Contractor Optimization (CCO) project is to create an engineering prototype of a tool for the contingency contractor element of total force planning during the Support for Strategic Analysis (SSA). An optimization model was developed to determine the optimal mix of military, Department of Defense (DoD) civilians, and contractors that accomplishes a set of user defined mission requirements at the lowest possible cost while honoring resource limitations and manpower use rules. An additional feature allows the model to understand the variability of the Total Force Mix when there is uncertainty in mission requirements.

  5. Contingency contractor optimization. Phase 3, model description and formulation.

    SciTech Connect (OSTI)

    Gearhart, Jared Lee; Adair, Kristin Lynn; Jones, Katherine A.; Bandlow, Alisa; Durfee, Justin D.; Jones, Dean A.; Martin, Nathaniel; Detry, Richard Joseph; Nanco, Alan Stewart; Nozick, Linda Karen [Cornell University

    2013-10-01

    The goal of Phase 3 the OSD ATL Contingency Contractor Optimization (CCO) project is to create an engineering prototype of a tool for the contingency contractor element of total force planning during the Support for Strategic Analysis (SSA). An optimization model was developed to determine the optimal mix of military, Department of Defense (DoD) civilians, and contractors that accomplishes a set of user defined mission requirements at the lowest possible cost while honoring resource limitations and manpower use rules. An additional feature allows the model to understand the variability of the Total Force Mix when there is uncertainty in mission requirements.

  6. Minnesota Liquefied Natural Gas Additions to and Withdrawals...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    703 54 22 -545 255 4 1980-2014 Additions 2,502 1,059 2,257 918 2,515 3,686 1980-2014 Withdrawals 1,798 1,005 2,235 1,463 2,261 3,683

  7. South Carolina Liquefied Natural Gas Additions to and Withdrawals from

    U.S. Energy Information Administration (EIA) Indexed Site

    Storage 15 -214 204 -100 -35 119 1980-2014 Additions 1,283 1,360 1,386 391 879 1,371 1980-2014 Withdrawals 1,268 1,574 1,183 491 914 1,252

  8. Tennessee Liquefied Natural Gas Additions to and Withdrawals from Storage

    U.S. Energy Information Administration (EIA) Indexed Site

    -882 -1,563 189 65 -1,262 -532 1980-2014 Additions 1,867 1,175 1,688 3,028 2,243 7,227 1980-2014 Withdrawals 2,748 2,738 1,499 2,963 3,505 7,759 1980

  9. Washington Liquefied Natural Gas Additions to and Withdrawals from Storage

    U.S. Energy Information Administration (EIA) Indexed Site

    532 0 100 16 -77 -1,094 1980-2014 Additions 2,937 1,157 1,664 1,154 905 1 1980-2014 Withdrawals 2,405 1,157 1,564 1,138 981 1,094

  10. Iowa Liquefied Natural Gas Additions to and Withdrawals from Storage

    U.S. Energy Information Administration (EIA) Indexed Site

    -244 146 14 428 -151 -647 1980-2014 Additions 1,652 1,458 1,858 1,408 2,252 2,054 1980-2014 Withdrawals 1,897 1,312 1,844 980 2,403 2,701

  11. North Carolina Liquefied Natural Gas Additions to and Withdrawals...

    U.S. Energy Information Administration (EIA) Indexed Site

    811 -2,643 2,194 -258 449 462 1980-2014 Additions 6,838 4,410 5,500 3,504 7,765 10,765 1980-2014 Withdrawals 6,027 7,052 3,305 3,762 7,315 10,30...

  12. Georgia Liquefied Natural Gas Additions to and Withdrawals from...

    U.S. Energy Information Administration (EIA) Indexed Site

    1,972 379 2,542 1,378 1,205 3,085 1980-2014 Additions 3,182 2,693 3,306 2,097 1,385 7,130 1980-2014 Withdrawals 1,210 2,314 764 719 180 4,046...

  13. Pennsylvania Liquefied Natural Gas Additions to and Withdrawals from

    U.S. Energy Information Administration (EIA) Indexed Site

    Storage 690 39 206 889 -82 -1,132 1980-2014 Additions 1,681 2,353 2,620 2,651 3,644 3,364 1980-2014 Withdrawals 2,371 2,314 2,415 1,763 3,726 4,496

  14. Massachusetts Liquefied Natural Gas Additions to and Withdrawals from

    U.S. Energy Information Administration (EIA) Indexed Site

    Storage -1,221 -963 -753 -1,384 -864 734 1980-2014 Additions 7,244 5,507 7,558 3,805 8,339 10,621 1980-2014 Withdrawals 8,465 6,470 8,311 5,189 9,203 9,887

  15. Additives and method for controlling clathrate hydrates in fluid systems

    DOE Patents [OSTI]

    Sloan, Jr., Earle Dendy; Christiansen, Richard Lee; Lederhos, Joseph P.; Long, Jin Ping; Panchalingam, Vaithilingam; Du, Yahe; Sum, Amadeu Kun Wan

    1997-01-01

    Discussed is a process for preventing clathrate hydrate masses from detrimentally impeding the possible flow of a fluid susceptible to clathrate hydrate formation. The process is particularly useful in the natural gas and petroleum production, transportation and processing industry where gas hydrate formation can cause serious problems. Additives preferably contain one or more five member, six member and/or seven member cyclic chemical groupings. Additives include polymers having lactam rings. Additives can also contain polyelectrolytes that are believed to improve conformance of polymer additives through steric hinderance and/or charge repulsion. Also, polymers having an amide on which a C.sub.1 -C.sub.4 group is attached to the nitrogen and/or the carbonyl carbon of the amide may be used alone, or in combination with ring-containing polymers for enhanced effectiveness. Polymers having at least some repeating units representative of polymerizing at least one of an oxazoline, an N-substituted acrylamide and an N-vinyl alkyl amide are preferred.

  16. Additives and method for controlling clathrate hydrates in fluid systems

    DOE Patents [OSTI]

    Sloan, E.D. Jr.; Christiansen, R.L.; Lederhos, J.P.; Long, J.P.; Panchalingam, V.; Du, Y.; Sum, A.K.W.

    1997-06-17

    Discussed is a process for preventing clathrate hydrate masses from detrimentally impeding the possible flow of a fluid susceptible to clathrate hydrate formation. The process is particularly useful in the natural gas and petroleum production, transportation and processing industry where gas hydrate formation can cause serious problems. Additives preferably contain one or more five member, six member and/or seven member cyclic chemical groupings. Additives include polymers having lactam rings. Additives can also contain polyelectrolytes that are believed to improve conformance of polymer additives through steric hindrance and/or charge repulsion. Also, polymers having an amide on which a C{sub 1}-C{sub 4} group is attached to the nitrogen and/or the carbonyl carbon of the amide may be used alone, or in combination with ring-containing polymers for enhanced effectiveness. Polymers having at least some repeating units representative of polymerizing at least one of an oxazoline, an N-substituted acrylamide and an N-vinyl alkyl amide are preferred.

  17. Ionic Liquids as Novel Engine Lubricants or Lubricant Additives |

    Broader source: Energy.gov (indexed) [DOE]

    Department of Energy Bench test results showed that compared with fully-formulated engine oils, selected low-viscosity ionic liquids, used as neat lubricants or basestock, produced significantly lower friction and engine wear PDF icon deer11_qu.pdf More Documents & Publications Ionic Liquids as Multifunctional Ashless Additives for Engine Lubrication

  18. Ionic Liquids as Novel Lubricants and Additives | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Presentation given at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER 2007). 13-16 August, 2007, Detroit, Michigan. Sponsored by the U.S. Department of Energy's (DOE) Office of FreedomCAR and Vehicle Technologies (OFCVT). PDF icon deer07_qu.pdf More Documents & Publications Ionic Liquids as Novel Engine Lubricants or Lubricant Additives

  19. Baseline Concept Description of a Small Modular High Temperature Reactor

    SciTech Connect (OSTI)

    Hans Gougar

    2014-05-01

    The objective of this report is to provide a description of generic small modular high temperature reactors (herein denoted as an smHTR), summarize their distinguishing attributes, and lay out the research and development (R&D) required for commercialization. The generic concepts rely heavily on the modular high temperature gas-cooled reactor designs developed in the 1980s which were never built but for which pre-licensing or certification activities were conducted. The concept matured more recently under the Next Generation Nuclear Plant (NGNP) project, specifically in the areas of fuel and material qualification, methods development, and licensing. As all vendor-specific designs proposed under NGNP were all both small or medium-sized and modular by International Atomic Energy Agency (IAEA) and Department of Energy (DOE) standards, the technical attributes, challenges, and R&D needs identified, addressed, and documented under NGNP are valid and appropriate in the context of Small Modular Reactor (SMR) applications. Although the term High Temperature Reactor (HTR) is commonly used to denote graphite-moderated, thermal spectrum reactors with coolant temperatures in excess of 650oC at the core outlet, in this report the historical term High Temperature Gas-Cooled Reactor (HTGR) will be used to distinguish the gas-cooled technology described herein from its liquid salt-cooled cousin. Moreover, in this report it is to be understood that the outlet temperature of the helium in an HTGR has an upper limit of 950 degrees C which corresponds to the temperature to which certain alloys are currently being qualified under DOEs ARC program. Although similar to the HTGR in just about every respect, the Very High Temperature Reactor (VHTR) may have an outlet temperature in excess of 950 degrees C and is therefore farther from commercialization because of the challenges posed to materials exposed to these temperatures. The VHTR is the focus of R&D under the Generation IV program and its specific R&D needs will be included in this report when appropriate for comparison. The distinguishing features of the HTGR are the refractory (TRISO) coated particle fuel, the low-power density, graphite-moderated core, and the high outlet temperature of the inert helium coolant. The low power density and fuel form effectively eliminate the possibility of core melt, even upon a complete loss of coolant pressure and flow. The graphite, which constitutes the bulk of the core volume and mass, provides a large thermal buffer that absorbs fission heat such that thermal transients occur over a timespan of hours or even days. As chemically-inert helium is already a gas, there is no coolant temperature or void feedback on the neutronics and no phase change or corrosion product that could degrade heat transfer. Furthermore, the particle coatings and interstitial graphite retain fission products such that the source terms at the plant boundary remain well below actionable levels under all anticipated nominal and off-normal operating conditions. These attributes enable the reactor to supply process heat to a collocated industrial plant with negligible risk of contamination and minimal dynamic coupling of the facilities (Figure 1). The exceptional retentive properties of coated particle fuel in a graphite matrix were first demonstrated in the DRAGON reactor, a European research facility that began operation in 1964.

  20. Description of Transmutation Library for Fuel Cycle System Analyses

    SciTech Connect (OSTI)

    Steven J. Piet; Samuel E. Bays; Edward A. Hoffman

    2010-08-01

    This report documents the Transmutation Library that is used in Fuel Cycle System Analyses. This version replaces the 2008 version.[Piet2008] The Transmutation Library has the following objectives: • Assemble past and future transmutation cases for system analyses. • For each case, assemble descriptive information such as where the case was documented, the purpose of the calculation, the codes used, source of feed material, transmutation parameters, and the name of files that contain raw or source data. • Group chemical elements so that masses in separation and waste processes as calculated in dynamic simulations or spreadsheets reflect current thinking of those processes. For example, the CsSr waste form option actually includes all Group 1A and 2A elements. • Provide mass fractions at input (charge) and output (discharge) for each case. • Eliminate the need for either “fission product other” or “actinide other” while conserving mass. Assessments of waste and separation cannot use “fission product other” or “actinide other” as their chemical behavior is undefined. • Catalog other isotope-specific information in one place, e.g., heat and dose conversion factors for individual isotopes. • Describe the correlations for how input and output compositions change as a function of UOX burnup (for LWR UOX fuel) or fast reactor (FR) transuranic (TRU) conversion ratio (CR) for either FR-metal or FR-oxide. This document therefore includes the following sections: • Explanation of the data set information, i.e., the data that describes each case. In no case are all of the data presented in the Library included in previous documents. In assembling the Library, we return to raw data files to extract the case and isotopic data, into the specified format. • Explanation of which isotopes and elements are tracked. For example, the transition metals are tracked via the following: two Zr isotopes, Zr-other, Tc99, Tc-other, two Mo-Ru-Rh-Pd isotopes, Mo-Ru-Rh-Pd-other, four other specific TM isotopes, and TM-other. Mo-Ru-Rh-Pd are separated because their content constrains the loading of waste in glass, so we have to know the mass of those elements independent of others. • Rules for collapsing long lists of isotopes (~1000) to the 81 items in the library. For each tracked isotope, we define which short-lived isotopes’ mass (at t=0) is included with the mass of the tracked isotope at t=0, which short-lived radioactive progeny must be accounted for when the tracked isotope decays, and to which of the other 80 items the mass of the tracked isotope goes when it decays. • Explanation of where raw data files can be found on the fuel cycle data portal. • Explanation of generic cross section sets • Explanation of isotope-specific parameters such as heat and dose conversion factors • Explanation of the LWR UOX burnup and FR TRU CR correlations.

  1. Baseline Concept Description of a Small Modular High Temperature Reactor

    SciTech Connect (OSTI)

    Gougar, Hans D.

    2014-10-01

    The objective of this report is to provide a description of generic small modular high temperature reactors (herein denoted as an smHTR), summarize their distinguishing attributes, and lay out the research and development (R&D) required for commercialization. The generic concepts rely heavily on the modular high temperature gas-cooled reactor designs developed in the 1980s which were never built but for which pre-licensing or certification activities were conducted. The concept matured more recently under the Next Generation Nuclear Plant (NGNP) project, specifically in the areas of fuel and material qualification, methods development, and licensing. As all vendor-specific designs proposed under NGNP were all both ‘small’ or medium-sized and ‘modular’ by International Atomic Energy Agency (IAEA) and Department of Energy (DOE) standards, the technical attributes, challenges, and R&D needs identified, addressed, and documented under NGNP are valid and appropriate in the context of Small Modular Reactor (SMR) applications. Although the term High Temperature Reactor (HTR) is commonly used to denote graphite-moderated, thermal spectrum reactors with coolant temperatures in excess of 650oC at the core outlet, in this report the historical term High Temperature Gas-Cooled Reactor (HTGR) will be used to distinguish the gas-cooled technology described herein from its liquid salt-cooled cousin. Moreover, in this report it is to be understood that the outlet temperature of the helium in an HTGR has an upper limit of 950 degrees C which corresponds to the temperature to which certain alloys are currently being qualified under DOE’s ARC program. Although similar to the HTGR in just about every respect, the Very High Temperature Reactor (VHTR) may have an outlet temperature in excess of 950 degrees C and is therefore farther from commercialization because of the challenges posed to materials exposed to these temperatures. The VHTR is the focus of R&D under the Generation IV program and its specific R&D needs will be included in this report when appropriate for comparison. The distinguishing features of the HTGR are the refractory (TRISO) coated particle fuel, the low-power density, graphite-moderated core, and the high outlet temperature of the inert helium coolant. The low power density and fuel form effectively eliminate the possibility of core melt, even upon a complete loss of coolant pressure and flow. The graphite, which constitutes the bulk of the core volume and mass, provides a large thermal buffer that absorbs fission heat such that thermal transients occur over a timespan of hours or even days. As chemically-inert helium is already a gas, there is no coolant temperature or void feedback on the neutronics and no phase change or corrosion product that could degrade heat transfer. Furthermore, the particle coatings and interstitial graphite retain fission products such that the source terms at the plant boundary remain well below actionable levels under all anticipated nominal and off-normal operating conditions. These attributes enable the reactor to supply process heat to a collocated industrial plant with negligible risk of contamination and minimal dynamic coupling of the facilities (Figure 1). The exceptional retentive properties of coated particle fuel in a graphite matrix were first demonstrated in the DRAGON reactor, a European research facility that began operation in 1964.

  2. Baseline Concept Description of a Small Modular High Temperature Reactor

    SciTech Connect (OSTI)

    Hans Gougar

    2014-05-01

    The objective of this report is to provide a description of generic small modular high temperature reactors (herein denoted as an smHTR), summarize their distinguishing attributes, and lay out the research and development (R&D) required for commercialization. The generic concepts rely heavily on the modular high temperature gas-cooled reactor designs developed in the 1980s which were never built but for which pre-licensing or certification activities were conducted. The concept matured more recently under the Next Generation Nuclear Plant (NGNP) project, specifically in the areas of fuel and material qualification, methods development, and licensing. As all vendor-specific designs proposed under NGNP were all both ‘small’ or medium-sized and ‘modular’ by International Atomic Energy Agency (IAEA) and Department of Energy (DOE) standards, the technical attributes, challenges, and R&D needs identified, addressed, and documented under NGNP are valid and appropriate in the context of Small Modular Reactor (SMR) applications. Although the term High Temperature Reactor (HTR) is commonly used to denote graphite-moderated, thermal spectrum reactors with coolant temperatures in excess of 650oC at the core outlet, in this report the historical term High Temperature Gas-Cooled Reactor (HTGR) will be used to distinguish the gas-cooled technology described herein from its liquid salt-cooled cousin. Moreover, in this report it is to be understood that the outlet temperature of the helium in an HTGR has an upper limit of 950 degrees C which corresponds to the temperature to which certain alloys are currently being qualified under DOE’s ARC program. Although similar to the HTGR in just about every respect, the Very High Temperature Reactor (VHTR) may have an outlet temperature in excess of 950 degrees C and is therefore farther from commercialization because of the challenges posed to materials exposed to these temperatures. The VHTR is the focus of R&D under the Generation IV program and its specific R&D needs will be included in this report when appropriate for comparison. The distinguishing features of the HTGR are the refractory (TRISO) coated particle fuel, the low-power density, graphite-moderated core, and the high outlet temperature of the inert helium coolant. The low power density and fuel form effectively eliminate the possibility of core melt, even upon a complete loss of coolant pressure and flow. The graphite, which constitutes the bulk of the core volume and mass, provides a large thermal buffer that absorbs fission heat such that thermal transients occur over a timespan of hours or even days. As chemically-inert helium is already a gas, there is no coolant temperature or void feedback on the neutronics and no phase change or corrosion product that could degrade heat transfer. Furthermore, the particle coatings and interstitial graphite retain fission products such that the source terms at the plant boundary remain well below actionable levels under all anticipated nominal and off-normal operating conditions. These attributes enable the reactor to supply process heat to a collocated industrial plant with negligible risk of contamination and minimal dynamic coupling of the facilities (Figure 1). The exceptional retentive properties of coated particle fuel in a graphite matrix were first demonstrated in the DRAGON reactor, a European research facility that began operation in 1964.

  3. South Carolina Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) South Carolina Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 345 736 35 132 362 484 403 545 503 490 1990's 394 346 339 1,231 847 927 976 6 56 1,204 2000's 1,131 1,330 605 716 813 776 784 1,089 1,872 1,283 2010's 1,360 1,386 391 879 1,371 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date:

  4. Tennessee Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Tennessee Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 1,222 2,508 2,491 977 2,376 2,105 1,766 1,135 2,109 1,879 1990's 3,008 1,522 2,759 2,663 2,985 2,414 2,809 1,875 1,816 2,181 2000's 884 1,606 1,849 1,889 913 1,065 1,391 2,312 2,186 1,867 2010's 1,175 1,688 3,028 2,243 7,227 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure

  5. Virginia Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Virginia Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 1,626 1,876 1,865 1,223 1,812 2,117 1,989 112 231 2,167 1990's 190 173 173 173 116 1,214 1,631 1,096 632 1,318 2000's 972 691 7,692 1,691 973 1,510 487 1,057 869 1,008 2010's 664 1,977 1,699 764 1,033 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company

  6. Washington Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Washington Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 0 0 0 0 0 0 0 0 0 0 1990's 96 2 0 3,167 2,340 1,902 2,284 2,193 902 2,502 2000's 1,268 2,039 1,094 3,067 2,628 2,526 2,283 2,406 1,760 2,937 2010's 1,157 1,664 1,154 905 1 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016

  7. Connecticut Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Connecticut Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 1,336 2,160 1,766 980 1,673 1,466 1,035 1,281 1,229 1,115 1990's 1,696 1,010 359 610 1,435 736 2,265 832 447 334 2000's 707 245 438 468 1,299 1,383 532 587 1,008 713 2010's 651 655 743 558 1,032 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data.

  8. Georgia Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Georgia Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 20,484 1,508 1,555 1,024 678 1,834 1,942 1,150 1,702 2,930 1990's 2,779 1,969 1,573 1,855 3,788 3,746 6,523 3,221 1,760 607 2000's 3,241 6,772 3,426 5,422 5,570 5,971 7,705 2,817 4,372 3,182 2010's 2,693 3,306 2,097 1,385 7,130 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid

  9. Indiana Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Indiana Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 1,107 1,966 4,352 785 2,714 923 777 806 6,321 737 1990's 1,027 1,517 849 2,320 2,638 1,316 4,337 2,520 1,589 2,000 2000's 795 1,477 1,726 2,197 1,602 831 1,447 2,663 982 691 2010's 1,983 609 0 925 2,193 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company

  10. Iowa Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Iowa Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 3,063 2,576 5,243 256 3,089 289 154 670 477 1,008 1990's 1,196 2,012 4,659 5,671 3,867 2,346 5,262 2,134 1,269 1,697 2000's 1,226 702 943 3,153 1,665 2,626 2,438 3,080 3,178 1,652 2010's 1,458 1,858 1,408 2,252 2,054 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of

  11. New Jersey Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) New Jersey Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 3,617 4,658 4,518 4,770 4,781 4,317 5,384 3,236 3,243 1,433 1990's 3,740 2,683 2,422 2,620 4,835 3,055 5,033 3,926 4,922 7,035 2000's 7,688 3,844 6,373 9,189 7,532 8,448 4,574 7,290 5,792 4,919 2010's 3,304 5,018 3,483 5,401 6,733 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid

  12. New York Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) New York Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 432 1,240 1,124 1,174 1,017 1,312 647 1,188 449 564 1990's 1,205 559 732 810 1,125 926 1,853 1,625 318 651 2000's 1,176 276 713 2,073 1,253 869 510 880 981 1,047 2010's 1,032 524 416 1,106 1,868 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data.

  13. North Carolina Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) North Carolina Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 597 1,497 1,372 1,145 1,511 1,164 1,663 1,609 2,151 1,597 1990's 2,023 1,219 1,030 1,681 2,118 1,572 2,708 2,016 1,286 4,086 2000's 4,168 5,477 4,026 8,122 5,039 6,445 2,639 5,744 4,493 6,838 2010's 4,410 5,500 3,504 7,765 10,765 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid

  14. Pennsylvania Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Pennsylvania Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 4,046 4,051 3,234 1,970 3,714 2,309 2,657 1,381 3,023 2,268 1990's 4,311 2,390 2,869 4,329 5,826 3,523 5,590 4,615 5,092 5,146 2000's 4,918 4,907 862 4,496 2,938 3,416 2,200 2,292 2,683 1,681 2010's 2,353 2,620 2,651 3,644 3,364 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid

  15. Louisiana Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Louisiana Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 0 0 22,711 96,945 0 0 0 0 0 0 1990's 27,903 33,284 12,545 30,677 17,823 5,032 7,016 30,419 30,385 0 2000's 0 0 0 0 0 0 0 0 1,446 0 2010's 0 0 0 0 0 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date:

  16. Maryland Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Maryland Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 443 714 676 235 650 786 769 482 764 697 1990's 769 657 804 696 939 1,831 4,881 1,439 813 715 2000's 684 2,926 3,814 4,437 2,157 3,203 296 631 1,002 4,859 2010's 366 394 386 461 604 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date:

  17. Massachusetts Natural Gas LNG Storage Additions (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Additions (Million Cubic Feet) Massachusetts Natural Gas LNG Storage Additions (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 7,885 15,234 14,021 6,599 9,844 9,261 6,184 5,732 5,782 10,004 1990's 6,586 4,399 5,147 5,531 5,550 5,898 6,107 5,049 2,712 3,934 2000's 4,480 6,382 5,683 10,035 9,485 7,643 5,966 10,006 5,863 7,244 2010's 5,507 7,558 3,805 8,339 10,621 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to

  18. Ionic Liquids as Lubricants or Additives - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Industrial Technologies Industrial Technologies Find More Like This Return to Search Ionic Liquids as Lubricants or Additives Oak Ridge National Laboratory Contact ORNL About This Technology Technology Marketing SummaryNew ionic liquids invented at ORNL show great promise as lubricants for aluminum and steel in combustion engines, bearings, and microelectromechanical systems (MEMS). The ammonium-based ionic liquids are strongly adsorbant on contact surfaces, leading to a more than 30% friction

  19. DOE Announces Additional Energy Efficiency Enforcement Action to Protect

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Consumers | Department of Energy Energy Efficiency Enforcement Action to Protect Consumers DOE Announces Additional Energy Efficiency Enforcement Action to Protect Consumers January 7, 2010 - 12:00am Addthis Washington, DC - The Department of Energy announced today that it has entered into a Consent Decree with Haier America resolving an investigation into whether Haier violated DOE's energy efficiency standards. DOE's investigation led Haier to determine that a parts defect caused certain

  20. DOE Announces Additional Steps in Developing Sustainable Biofuels Industry

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy Steps in Developing Sustainable Biofuels Industry DOE Announces Additional Steps in Developing Sustainable Biofuels Industry October 7, 2008 - 4:14pm Addthis Releases Results from Preliminary Intermediate Blends Report, Continues Commitment of Commercial Scale Biorefinery, Announces $7 Million for New Biofuels Projects WASHINGTON - Secretary of Energy Samuel W. Bodman and Secretary of Agriculture Ed Schafer today released the National Biofuels Action Plan (NBAP). The

  1. Evaluation of Additive Manufacturing for Composite Part Molds

    SciTech Connect (OSTI)

    Duty, Chad E.; Springfield, Robert M.

    2015-02-01

    The ORNL Manufacturing Demonstration Facility (MDF) collaborated with Tru-Design to test the quality and durability of molds used for making fiber reinforced composites using additive manufacturing. The partners developed surface treatment techniques including epoxy coatings and machining to improve the quality of the surface finish. Test samples made using the printed and surface finished molds demonstrated life spans suitable for one-of-a-kind and low-volume applications, meeting the project objective.

  2. Additive for iron disulfide cathodes used in thermal batteries

    DOE Patents [OSTI]

    Not Available

    1982-03-23

    The invention comprises thermal batteries employing an FeS/sub 2/ depolarizer itself. A minor amount of CaSi/sub 2/ preferably 1-3% by weight is provided as an additive in the FeS/sub 2/ depolarizer to eliminate the voltage transient (spike) which normally occurs upon activation of batteries of this type. The amount of FeS/sub 2/ by weight generally comprises 64 to 90%.

  3. Additive for iron disulfide cathodes used in thermal batteries

    DOE Patents [OSTI]

    Armijo, James R.; Searcy, Jimmie Q.

    1983-01-01

    The invention comprises thermal batteries employing an FeS.sub.2 depolarizer, i.e. cathode material, and the depolarizer itself. A minor amount of CaSi.sub.2 preferably, 1-3% by weight is provided as an additive in the FeS.sub.2 depolarizer to eliminate the voltage transient (spike) which normally occurs upon activation of batteries of this type. The amount of FeS.sub.2 by weight generally comprises 64-90%.

  4. Additional public meeting on plutonium disposition on September 18

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Development Additional Resources Photo: DARHT's Accelerators help create the x-rays at DARHT, the world's most advanced radiography facility. Reports 2013 Stewardship Science Academic Programs Annual 2012 Stewardship Science Academic Alliances Annual 2011 Stewardship Science Academic Alliances Annual FY 2011 Stockpile Stewardship and Management Plan, Annex A (April 7, 2010) Supplement to the Stockpile Stewardship Plan, Fiscal Years 2010-2014 (December 2009) Advances in Matter Under Extreme

  5. Additive Manufacturing - Materials by Design - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Industrial Technologies Industrial Technologies Early Stage R&D Early Stage R&D Advanced Materials Advanced Materials Find More Like This Return to Search Additive Manufacturing - Materials by Design Lawrence Livermore National Laboratory Contact LLNL About This Technology Technology Marketing SummaryLivermore materials scientists and engineers are designing and building new materials that will open up new spaces on many Ashby material selection charts, such as those for stiffness and

  6. UCRG JC-119253 PREPRINT Clean, Agile Alternative Binders, Additives and

    Office of Scientific and Technical Information (OSTI)

    UCRG JC-119253 PREPRINT Clean, Agile Alternative Binders, Additives and Plasticizers for Propellant and Explosive Formulations D. Mark Hoffman, Tom W. Hawkins, Geoffrey A. Lindsay, Robert B. Wardle, and Gerald E. Manser This paper was prepared for submittal to the Life Cycles of Energetic Materials Meeting i n Del M a r , C A December 11-16,1994 December 1994 Thisisapreprintof apaperintendedforpubliation ina joumalorpmceedings. S i n c e changes may be made before publication, thb preprint is

  7. Environmental site description for a Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) production plant at the Oak Ridge Gaseous Diffusion Plant Site

    SciTech Connect (OSTI)

    Not Available

    1991-09-01

    In January 1990, the Secretary of Energy approved a plan for the demonstration and deployment of the Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) technology, with the near-term goal to provide the necessary information to make a deployment decision by November 1992. The U-AVLIS process is based on electrostatic extraction of photoionized U-235 atoms from an atomic vapor stream created by electron-beam vaporization of uranium metal alloy. A programmatic document for use in screening DOE sites to locate the U-AVLIS production plant was developed and implemented in two parts (Wolsko et al. 1991). The first part consisted of a series of screening analyses, based on exclusionary and other criteria, that identified a reasonable number of candidate sites. These sites were then subjected to a more rigorous and detailed comparative analysis for the purpose of developing a short list of reasonable alternative sites for later environmental examination. This environmental site description (ESD) provides a detailed description of the ORGDP site and vicinity suitable for use in an environmental impact statement (EIS). The report is based on existing literature, data collected at the site, and information collected by Argonne National Laboratory (ANL) staff during a site visit. The organization of the ESD is as follows. Topics addressed in Sec. 2 include a general site description and the disciplines of geology, water resources, biotic resources, air resources, noise, cultural resources, land use, socioeconomics, and waste management. Identification of any additional data that would be required for an EIS is presented in Sec. 3. Following the site description and additional data requirements, Sec. 4 provides a short, qualitative assessment of potential environmental issues. 37 refs., 20 figs., 18 tabs.

  8. Modeling uranium transport in acidic contaminated groundwater with base addition

    SciTech Connect (OSTI)

    Zhang, Fan; Luo, Wensui; Parker, Jack C.; Brooks, Scott C; Watson, David B; Jardine, Philip; Gu, Baohua

    2011-01-01

    This study investigates reactive transport modeling in a column of uranium(VI)-contaminated sediments with base additions in the circulating influent. The groundwater and sediment exhibit oxic conditions with low pH, high concentrations of NO{sub 3}{sup -}, SO{sub 4}{sup 2-}, U and various metal cations. Preliminary batch experiments indicate that additions of strong base induce rapid immobilization of U for this material. In the column experiment that is the focus of the present study, effluent groundwater was titrated with NaOH solution in an inflow reservoir before reinjection to gradually increase the solution pH in the column. An equilibrium hydrolysis, precipitation and ion exchange reaction model developed through simulation of the preliminary batch titration experiments predicted faster reduction of aqueous Al than observed in the column experiment. The model was therefore modified to consider reaction kinetics for the precipitation and dissolution processes which are the major mechanism for Al immobilization. The combined kinetic and equilibrium reaction model adequately described variations in pH, aqueous concentrations of metal cations (Al, Ca, Mg, Sr, Mn, Ni, Co), sulfate and U(VI). The experimental and modeling results indicate that U(VI) can be effectively sequestered with controlled base addition due to sorption by slowly precipitated Al with pH-dependent surface charge. The model may prove useful to predict field-scale U(VI) sequestration and remediation effectiveness.

  9. The effect of feedstock additives on FCC catalyst deactivation

    SciTech Connect (OSTI)

    Hughes, R.; Koon, C.L.; McGhee, B.

    1995-12-31

    Fluid catalytic cracking is a major petroleum refining process and because of this the deactivation of FCC catalysts by coke deposition has been the subject of considerable investigation during the past 50 years. Nevertheless, a lack of understanding of the fundamental understanding of processes leading to coke formation still exists. Basic studies using Zeolites have usually involved excessively high levels of coke deposits compared to normal FCC operation. The present study addresses coke formation at realistic levels of 0.5 to 1.0% w/w using a standard MAT reactor in which concentrations of 1% and 10% of various additives were added to the n-hexadecane feedstock. These additives included, quinoline, phenanthrene, benzofuran, thianaphthene and indene. The coke formed was characterised by mass spectrometry and was significantly aliphatic in nature, the amount formed increasing in the order quinoline, phenanthrene, thianaphthene, benzofuran, indene. Quinoline acts primarily as a poison, whereas the other additives tend to promote coke formation in n-hexadecane cracking.

  10. Comprehensive mitigation assessment process (COMAP) - Description and instruction manual

    SciTech Connect (OSTI)

    Makundi, Willy; Sathaye, Jayant

    2001-11-09

    In order to prepare policies and plans to reduce GHG emissions, national policy-makers need information on the costs and benefits of different mitigation options in addition to their carbon implications. Policy-makers must weigh the costs, benefits, and impacts of climate change mitigation and adaptation options, in the face of competition for limited resources. The policy goal for mitigation options in the land use sector is to identify which mix of options is likely to best achieve the desired forestry service and production objectives at the least cost, while attempting to maximize economic and social benefits, and minimize negative environmental and social impacts. Improved national-level cost estimates of response options in the land use sector can be generated by estimating the costs and benefits of different forest management practices appropriate for specific country conditions which can be undertaken within the constraint of land availability and its opportunity cost. These co st and land use estimates can be combined to develop cost curves, which would assist policy-makers in constructing policies and programs to implement forest responses.

  11. Description of the Columbia Basin Wind Energy Study (CBWES)

    SciTech Connect (OSTI)

    Berg, Larry K.; Pekour, Mikhail S.; Nelson, Danny A.

    2012-10-01

    The purpose of this Technical Report is to provide background information about the Columbia Basin Wind Energy Study (CBWES). This study, which was supported by the U.S. Department of Energy’s Wind and Water Power Program, was conducted from 16 November 2010 through 21 March 2012 at a field site in northeastern Oregon. The primary goal of the study was to provide profiles of wind speed and wind direction over the depth of the boundary layer in an operating wind farm located in an area of complex terrain. Measurements from propeller and vane anemometers mounted on a 62 m tall tower, Doppler Sodar, and Radar Wind Profiler were combined into a single data product to provide the best estimate of the winds above the site during the first part of CBWES. An additional goal of the study was to provide measurements of Turbulence Kinetic Energy (TKE) near the surface. To address this specific goal, sonic anemometers were mounted at two heights on the 62 m tower on 23 April 2011. Prior to the deployment of the sonic anemometers on the tall tower, a single sonic anemometer was deployed on a short tower 3.1 m tall that was located just to the south of the radar wind profiler. Data from the radar wind profiler, as well as the wind profile data product are available from the Atmospheric Radiation Measurements (ARM) Data Archive (http://www.arm.gov/data/campaigns). Data from the sonic anemometers are available from the authors.

  12. RELAP5 Model Description and Validation for the BR2 Loss-of-Flow Experiments

    SciTech Connect (OSTI)

    Licht, J. R.; Dionne, B.; Van den Branden, G.; Sikik, E.; Koonen, E.

    2015-07-01

    This paper presents a description of the RELAP5 model, the calibration method used to obtain the minor loss coefficients from the available hydraulic data and the LOFA simulation results compared to the 1963 experimental tests for HEU fuel.

  13. ORISE Contract, PART I … THE SCHEDULE, Section C Description/Specifications/Work Statement

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    PART I - THE SCHEDULE SECTION C DESCRIPTION/SPECIFICATIONS/WORK STATEMENT C.1 PERFORMANCE WORK STATEMENT (NOV 2004) ................................................... 3 1.0 SCOPE............................................................................................................................... 3 2.0 PERFORMANCE WORK STATEMENT OBJECTIVES .......................................... 4 3.0 RELATED SERVICES (NOV 2004)

  14. Attachment A: Site Description Nevada National Security Site Environmental Report 2014

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Attachment A: Site Description Nevada National Security Site Environmental Report 2014 ATT-A-i Table of Contents List of Figures ....................................................................................................................................................... A-ii List of Tables ......................................................................................................................................................... A-ii Acronyms and Abbreviations

  15. Electrolyte additive for lithium rechargeable organic electrolyte battery

    SciTech Connect (OSTI)

    Behl, W.K.; Chin, D.T.

    1988-02-08

    This invention relates in general to a rechargeable lithium organic electrolyte battery and, in particular, to an electrolyte additive for such a battery that provides overcharge protection. Rechargeable lithium-organic electrolyte batteries are being developed to provide low-cost, high-energy-density power sources for communication, night vision and various other Army applications. Typically, a rechargeable lithium organic electrolyte battery includes a lithium anode, a cathode including compounds such as titanium disulfide, molybdenum oxide, molybdenum sulfide, vanadium oxide, vanadium sulfide, chromium oxide, etc an electrolyte solution including an inorganic lithium salt such as lithium hexafluoroarsenate, lithium perchlorate, etc.

  16. System and method for high power diode based additive manufacturing

    DOE Patents [OSTI]

    El-Dasher, Bassem S.; Bayramian, Andrew; Demuth, James A.; Farmer, Joseph C.; Torres, Sharon G.

    2016-04-12

    A system is disclosed for performing an Additive Manufacturing (AM) fabrication process on a powdered material forming a substrate. The system may make use of a diode array for generating an optical signal sufficient to melt a powdered material of the substrate. A mask may be used for preventing a first predetermined portion of the optical signal from reaching the substrate, while allowing a second predetermined portion to reach the substrate. At least one processor may be used for controlling an output of the diode array.

  17. Lime addition to heavy crude oils prior to coking

    SciTech Connect (OSTI)

    Kessick, M. A.; George, Z. M.; Schneider, L. G.

    1985-06-04

    The sulphur emissive capability, on combustion, of coke which is formed during upgrading of sulphur-containing heavy crude oils, including oil sands bitumen, or residua is decreased by the addition of slaked lime or calcium oxide to the heavy crude oil prior to coking. The presence of the slaked lime or calcium oxide leads to an increased yield of liquid distillates at coking temperatures of about 450/sup 0/ to about 500/sup 0/ C. Ash remaining after combustion of the coke may be leached to recover nickel and vanadium values therefrom.

  18. Microsoft Word - Directives Requiring Additional Documentation.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Requiring Additional Documentation 4-3-09 Prepared in accordance with Appendix D, DOE Order 251.1C, Departmental Directives Program dated 01/15/2009. 1 Notices 1 DOE N 203.1 Software Quality Assurance Orders 1 DOE O 151.1C Comprehensive Emergency Management System 2 DOE O 210.2 DOE Corporate Operating Experience Program 3 DOE O 225.1A Accident Investigations 4 DOE O 226.1A Implementation of Department of Energy Oversight Policy 5 DOE O 231.1A, Chg 1 Environment, Safety, and Health Reporting 6

  19. Addition of Safe Havens Increases WIPP Underground Safety

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    WIPP UPDATE: November 24, 2015 Addition of Safe Havens Increases WIPP Underground Safety The WIPP site has made significant safety improvements. Recently, eight underground safe havens (or refuge chambers) were delivered to the site and will be downloaded into the WIPP underground prior to the restart of waste disposal operations. The safe havens are about 28 feet long, 8 feet wide and 7.25 feet high and weigh approximately 19,000 pounds. Each unit is equipped to house 20 people for at least 36

  20. SWEPP Assay System Version 2.0 software design description

    SciTech Connect (OSTI)

    East, L.V.; Marwil, E.S.

    1996-08-01

    The Idaho National Engineering Laboratory (INEL) Stored Waste Examination Pilot Plant (SWEPP) operations staff use nondestructive analysis methods to characterize the radiological contents of contact-handled radioactive waste containers. Containers of waste from Rocky Flats Environmental Technology Site and other Department of Energy (DOE) sites are currently stored at SWEPP. Before these containers can be shipped to the Waste Isolation Pilot Plant (WIPP), SWEPP must verify compliance with storage, shipping, and disposal requirements. This program has been in operation since 1985 at the INEL Radioactive Waste Management Complex (RWMC). One part of the SWEPP program measures neutron emissions from the containers and estimates the mass of plutonium and other transuranic (TRU) isotopes present. A Passive/Active Neutron (PAN) assay system developed at the Los Alamos National Laboratory is used to perform these measurements. A computer program named NEUT2 was originally used to perform the data acquisition and reduction functions for the neutron measurements. This program was originally developed at Los Alamos and extensively modified by a commercial vendor of PAN systems and by personnel at the INEL. NEUT2 uses the analysis methodology outlined, but no formal documentation exists on the program itself. The SWEPP Assay System (SAS) computer program replaced the NEUT2 program in early 1994. The SAS software was developed using an `object model` approach and is documented in accordance with American National Standards Institute (ANSI) and Institute of Electrical and Electronic Engineers (IEEE) standards. The new program incorporates the basic analysis algorithms found in NEUT2. Additional functionality and improvements include a graphical user interface, the ability to change analysis parameters without program code modification, an `object model` design approach and other features for improved flexibility and maintainability.

  1. NDMAS System and Process Description (Technical Report) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Technical Report: NDMAS System and Process Description Citation Details In-Document Search Title: NDMAS System and Process Description Experimental data generated by the Very High Temperature Reactor Program need to be more available to users in the form of data tables on Web pages that can be downloaded to Excel or in delimited text formats that can be used directly for input to analysis and simulation codes, statistical packages, and graphics software. One solution that can provide current and

  2. NAICS Codes @ Headquarters Description: NAICS Codes used at Headquarters Procurement Services

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    NAICS Codes @ Headquarters Description: NAICS Codes used at Headquarters Procurement Services Filters: Signed Date only show values between , Contracting Agency ID show only ('8900'), Contracting Office ID show only ('00001'), Date Signed only show values between '05/01/2011' and '04/30/2012', Last Modified Date only show values between Contracting Agency ID: 8900, Contracting Office ID: 00001 NAICS Code NAICS Description Action Obligation 541519 OTHER COMPUTER RELATED SERVICES 341

  3. Two-fluid description of wave-particle interactions in strong Buneman

    Office of Scientific and Technical Information (OSTI)

    turbulence (Journal Article) | SciTech Connect Two-fluid description of wave-particle interactions in strong Buneman turbulence Citation Details In-Document Search Title: Two-fluid description of wave-particle interactions in strong Buneman turbulence To understand the nature of anomalous resistivity in magnetic reconnection, we investigate turbulence-induced momentum transport and energy dissipation while a plasma is unstable to the Buneman instability in force-free current sheets. Using 3D

  4. Health, Safety & Environment System Description and Worker Safety & Health Program

    National Nuclear Security Administration (NNSA)

    FY2015 HEALTH, SAFETY AND ENVIRONMENT MANAGEMENT SYSTEM DESCRIPTION and WORKER SAFETY & HEALTH PROGRAM Honeywell Federal Manufacturing & Technologies HS&E Management System Description 1 Honeywell Approval: KCFO Approval: Original Signed by Don Fitzpatrick 8/27/14 Original Signed by Sherry Kinsey-Cannon 8/27/14 Donald J. Fitzpatrick, Director Date Sherry Kinsey-Cannon, Date HSE&F Acting Assistant Manager Office of Operations KCFO Worker Safety & Health Program 2 Honeywell

  5. International Workshops to Foster Implementation of the IAEA Additional Protocol

    SciTech Connect (OSTI)

    Killinger, Mark H.; Coates, Cameron W.; Bedke, Michael L.

    2003-07-14

    A country’s adherence to the International Atomic Energy Agency’s (IAEA) Additional Protocol is an important statement to the world of that country’s commitment to nuclear nonproliferation. Without the Additional Protocol (AP) it is possible, as demonstrated in Iraq, for a country party to the Non-Proliferation Treaty (NPT) to clandestinely work toward nuclear weapons and be undetected by the IAEA. This is because classical safeguards under the NPT are directed at diversion of nuclear material from declared activities. But a country may instead build undeclared activities to produce weapons-grade nuclear material. The AP is directed at detecting those undeclared activities. As of May 2003, 73 countries had signed the AP, but only 35 have entered into force. To further adherence to the AP, the IAEA has held regional, high-level seminars in Japan, South Africa, Kazakhstan, Peru, Romania, and Malaysia to explain AP provisions. To supplement these policy-level seminars, the U.S. Department of Energy (DOE) has undertaken to develop a set of modules of technical competencies required to implement the AP. The intent is to work closely with the IAEA by providing these technical competencies to countries as well as to complement the IAEA’s regional seminars and other outreach efforts. This paper briefly describes the technical competency modules.

  6. Ionic Liquids with Ammonium Cations as Lubricants or Additives

    SciTech Connect (OSTI)

    Qu, Jun; Blau, Peter Julian; Dai, Sheng; Luo, Huimin; Truhan, Jr., John J

    2006-01-01

    Friction and wear are estimated to cost 6% of the US gross national product, or around $700 billion annually. A new class of more effective lubricants could lead to huge energy savings. Limited recent literature has suggested potential for using room-temperature ionic liquids as lubricants, however only a few out of millions (or more) of species have been evaluated. Recent ORNL work discovered a new category of ionic liquids with ammonium cations that have demonstrated promising lubricating properties as net lubricants or lubricant additives, particularly in lubricating difficult-to-lubricate metals like aluminum. More than 30% friction reduction has been observed on ammonium-based ionic liquids compared to conventional hydrocarbon oils. The inherent polarity of ionic liquids is believed to provide strong adhesion to contact surfaces and form a boundary lubricating film leading to friction and wear reductions. Other advantages of ionic liquids include (1) negligible volatility, (2) high thermal stability, (3) non-flammability, and (4) better intrinsic properties that eliminate the necessity of many expensive lubricant additives. With very flexible molecular structures, this new class of lubricants, particularly ammonium-based ionic liquids, can be tailored to fit a big variety of applications including but not limited to bearings, combustion engines, MEMS, and metal forming.

  7. Fuel, lubricant and additive effects in combustion chamber deposit formation

    SciTech Connect (OSTI)

    Kelemen, S.R.; Homan, H.S.

    1996-10-01

    CCD causes octane requirement increase (ORI) and can potentially contributes to exhaust emissions and combustion chamber deposit interference (CCDI). Experiments were conducted to identify the separate fuel, lubricant and additive contributions to the amount and composition of CCD. CCD originates from multiple sources. Gasoline hydrocarbon components, gasoline additives, engine lubricant, and atmospheric nitrogen contribute to CCD in different ways. With some fuels the engine lubricant is the main contributor to CCD and this is shown by the high ash level in the CCD. For other fuels CCD is predominantly organic. Significant amounts of nitrogen were found in the CCD even when the fuel and lubricant were nitrogen free. The pyrolysis reactivity of different CCDs was studied to gain an understanding about the transformations that potentially happen over longer times and lower temperatures on the combustion chamber walls. In all cases during mild pyrolysis (375{degrees}C) there was a substantial increase in the level of aromatic carbon and a decrease in the level of organic oxygen. The largest increases in the amount of aromatic carbon occurred for CCDs that were the least aromatic.

  8. Monitoring system for the quality assessment in additive manufacturing

    SciTech Connect (OSTI)

    Carl, Volker

    2015-03-31

    Additive Manufacturing (AM) refers to a process by which a set of digital data -representing a certain complex 3dim design - is used to grow the respective 3dim real structure equal to the corresponding design. For the powder-based EOS manufacturing process a variety of plastic and metal materials can be used. Thereby, AM is in many aspects a very powerful tool as it can help to overcome particular limitations in conventional manufacturing. AM enables more freedom of design, complex, hollow and/or lightweight structures as well as product individualisation and functional integration. As such it is a promising approach with respect to the future design and manufacturing of complex 3dim structures. On the other hand, it certainly calls for new methods and standards in view of quality assessment. In particular, when utilizing AM for the design of complex parts used in aviation and aerospace technologies, appropriate monitoring systems are mandatory. In this respect, recently, sustainable progress has been accomplished by joining the common efforts and concerns of a manufacturer Additive Manufacturing systems and respective materials (EOS), along with those of an operator of such systems (MTU Aero Engines) and experienced application engineers (Carl Metrology), using decent know how in the field of optical and infrared methods regarding non-destructive-examination (NDE). The newly developed technology is best described by a high-resolution layer by layer inspection technique, which allows for a 3D tomography-analysis of the complex part at any time during the manufacturing process. Thereby, inspection costs are kept rather low by using smart image-processing methods as well as CMOS sensors instead of infrared detectors. Moreover, results from conventional physical metallurgy may easily be correlated with the predictive results of the monitoring system which not only allows for improvements of the AM monitoring system, but finally leads to an optimisation of the quality and insurance of material security of the complex structure being manufactured. Both, our poster and our oral presentation will explain the data flow between the above mentioned parties involved. A suitable monitoring system for Additive Manufacturing will be introduced, along with a presentation of the respective high resolution data acquisition, as well as the image processing and the data analysis allowing for a precise control of the 3dim growth-process.

  9. Multistage network with an additional stage for fault tolerance

    SciTech Connect (OSTI)

    Adams, G.B. III; Siegel, H.J.

    1982-01-01

    The extra stage cube (ESC) network, a fault tolerant structure, is proposed for use in large-scale parallel and distributed supercomputer systems. This network is derived from the generalised cube network by the addition of one stage of interchange boxes and a bypass capability for two stages. It is shown that the ESC provides fault tolerance for any single failure. Further, the network can be controlled even when it has a single failure, using a simple modification of a routing tag scheme proposed for the generalised cube. Both one-to-one and broadcast connections under routing tag control are performable by the faulted ESC. The effects of the extra stage on the partitioning and permuting abilities of the network are described. 19 references.

  10. Decontamination formulation with additive for enhanced mold remediation

    DOE Patents [OSTI]

    Tucker, Mark D.; Irvine, Kevin; Berger, Paul; Comstock, Robert

    2010-02-16

    Decontamination formulations with an additive for enhancing mold remediation. The formulations include a solubilizing agent (e.g., a cationic surfactant), a reactive compound (e.g., hydrogen peroxide), a carbonate or bicarbonate salt, a water-soluble bleaching activator (e.g., propylene glycol diacetate or glycerol diacetate), a mold remediation enhancer containing Fe or Mn, and water. The concentration of Fe.sup.2+ or Mn.sup.2+ ions in the aqueous mixture is in the range of about 0.0001% to about 0.001%. The enhanced formulations can be delivered, for example, as a foam, spray, liquid, fog, mist, or aerosol for neutralization of chemical compounds, and for killing certain biological compounds or agents and mold spores, on contaminated surfaces and materials.

  11. Improving properties of Mg with AlCu additions

    SciTech Connect (OSTI)

    Rashad, Muhammad; Pan, Fusheng; Asif, Muhammad; Hussain, Shahid; Saleem, Muhammad

    2014-09-15

    The present work reports improvement in tensile properties of the Mg matrix reinforced with micron-sized copperaluminum particulate hybrids. The AlCu particulate hybrids were incorporated into the Mg matrix through powder metallurgy method. The synthesized alloys exhibited homogeneously dispersed Mg{sub 2}Cu particles in the matrix, therefore leading to a 110% increase in yield strength (221 MPa) and a 72% enhancement in ultimate tensile strength (284 MPa) by addition of 1.0 wt.%Al0.6 wt.%Cu particle hybrids. Optical microscopy, scanning election microscopy, transmission electron microscopy and X-ray diffraction were used to investigate the microstructure and intermetallic phases of the synthesized alloys. - Highlights: Mg matrix is reinforced with AlCu particulate hybrids. Powder metallurgic method is used to fabricate the alloys. Tensile strength and ductility were increased simultaneously.

  12. Motor stator using corner scraps for additional electrical components

    DOE Patents [OSTI]

    Hsu, John S.; Su, Gui-Jia; Adams, Donald J.; Nagashima, James M.; Stancu, Constantin; Carlson, Douglas S.; Smith, Gregory S.

    2004-03-16

    A method for making a motor and auxiliary devices with a unified stator body comprises providing a piece of material (10) having an area larger than a cross section of the stator (11), removing material from the piece of material (10) to form a pattern for a cross section of a core (11) for the stator, and removing material from the piece of material (10) outside the cross section of the core of the stator (11) to allow positioning of cores (22, 23, 24) for supporting windings (25, 26, 27) of least one additional electromagnetic device, such as a transformer (62) in a dc-to-dc converter (61, 62) that provides a low. voltage dc output. An article of manufacture made according to the invention is also disclosed and apparatus made with the method and article of manufacture are also disclosed.

  13. Monitored Geologic Repository Operations Monitoring and Control System Description Document

    SciTech Connect (OSTI)

    E.F. Loros

    2000-06-29

    The Monitored Geologic Repository Operations Monitoring and Control System provides supervisory control, monitoring, and selected remote control of primary and secondary repository operations. Primary repository operations consist of both surface and subsurface activities relating to high-level waste receipt, preparation, and emplacement. Secondary repository operations consist of support operations for waste handling and treatment, utilities, subsurface construction, and other selected ancillary activities. Remote control of the subsurface emplacement operations, as well as, repository performance confirmation operations are the direct responsibility of the system. In addition, the system monitors parameters such as radiological data, air quality data, fire detection status, meteorological conditions, unauthorized access, and abnormal operating conditions, to ensure a safe workplace for personnel. Parameters are displayed in a real-time manner to human operators regarding surface and subsurface conditions. The system performs supervisory monitoring and control for both important to safety and non-safety systems. The system provides repository operational information, alarm capability, and human operator response messages during emergency response situations. The system also includes logic control to place equipment, systems, and utilities in a safe operational mode or complete shutdown during emergency response situations. The system initiates alarms and provides operational data to enable appropriate actions at the local level in support of emergency response, radiological protection response, evacuation, and underground rescue. The system provides data communications, data processing, managerial reports, data storage, and data analysis. This system's primary surface and subsurface operator consoles, for both supervisory and remote control activities, will be located in a Central Control Center (CCC) inside one of the surface facility buildings. The system consists of instrument and control equipment and components necessary to provide human operators with sufficient information to monitor and control the operation of the repository in an efficient and safe manner. The system consists of operator consoles and workstations, multiple video display terminals, communications and interfacing equipment, and instrument and control software with customized configuration to meet the needs of the Monitored Geologic Repository (MGR). Process and logic controllers and the associated input/output units of each system interfaced with this system will be configured into Remote Terminal Units (RTU) and located close to the systems to be monitored and controlled. The RTUs are configured to remain operational should communication with CCC operations be lost. The system provides closed circuit television to selectively view systems, operations, and equipment areas and to aid in the operation of mechanical systems. Control and monitoring of site utility systems will be located in the CCC. Site utilities include heating, ventilation, and air conditioning equipment; plant compressed air; plant water; firewater; electrical systems; and inert gases, such as nitrogen, if required. This system interfaces with surface and subsurface systems that either generate output data or require remote control input. The system interfaces with the Site Communications System for bulk storage of operational data, on-site and off-site communication, and a plant-wide public announcement system. The system interfaces with the Safeguards and Security System to provide operational status and emergency alarm indications. The system interfaces with the Site Operation System to provide site wide acquisition of data for analysis and reports, historical information for trends, utility information for plant operation, and to receive operating plans and procedures.

  14. Soil microbial responses to nitrogen addition in arid ecosystems

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Sinsabaugh, Robert L.; Belnap, Jayne; Rudgers, Jennifer; Kuske, Cheryl R.; Martinez, Noelle; Sandquist, Darren

    2015-08-14

    The N cycle of arid ecosystems is influenced by low soil organic matter, high soil pH, and extremes in water potential and temperature that lead to open canopies and development of biological soil crusts (biocrusts). We investigated the effects of N amendment on soil microbial dynamics in a Larrea tridentata-Ambrosia dumosa shrubland site in southern Nevada USA. Sites were fertilized with a NO3-NH4 mix at 0, 7, and 15 kg N ha-1 y-1 from March 2012 to March 2013. In March 2013, biocrust (0–0.5 cm) and bulk soils (0–10 cm) were collected beneath Ambrosia canopies and in the interspaces betweenmore » plants. Biomass responses were assessed as bacterial and fungal SSU rRNA gene copy number and chlorophyll a concentration. Metabolic responses were measured by five ecoenzyme activities and rates of N transformation. With most measures, nutrient availability, microbial biomass, and process rates were greater in soils beneath the shrub canopy compared to the interspace between plants, and greater in the surface biocrust horizon compared to the deeper 10 cm soil profile. Most measures responded positively to experimental N addition. Effect sizes were generally greater for bulk soil than biocrust. Results were incorporated into a meta-analysis of arid ecosystem responses to N amendment that included data from 14 other studies. Effect sizes were calculated for biomass and metabolic responses. Regressions of effect sizes, calculated for biomass, and metabolic responses, showed similar trends in relation to N application rate and N load (rate × duration). The critical points separating positive from negative treatment effects were 88 kg ha-1 y-1 and 159 kg ha-1, respectively, for biomass, and 70 kg ha-1 y-1 and 114 kg ha-1, respectively, for metabolism. These critical values are comparable to those for microbial biomass, decomposition rates and respiration reported in broader meta-analyses of N amendment effects in mesic ecosystems. The large effect sizes at low N addition rates indicate that arid ecosystems are sensitive to modest increments in anthropogenic N deposition.« less

  15. Soil microbial responses to nitrogen addition in arid ecosystems

    SciTech Connect (OSTI)

    Sinsabaugh, Robert L.; Belnap, Jayne; Rudgers, Jennifer; Kuske, Cheryl R.; Martinez, Noelle; Sandquist, Darren

    2015-08-14

    The N cycle of arid ecosystems is influenced by low soil organic matter, high soil pH, and extremes in water potential and temperature that lead to open canopies and development of biological soil crusts (biocrusts). We investigated the effects of N amendment on soil microbial dynamics in a Larrea tridentata-Ambrosia dumosa shrubland site in southern Nevada USA. Sites were fertilized with a NO3-NH4 mix at 0, 7, and 15 kg N ha-1 y-1 from March 2012 to March 2013. In March 2013, biocrust (0–0.5 cm) and bulk soils (0–10 cm) were collected beneath Ambrosia canopies and in the interspaces between plants. Biomass responses were assessed as bacterial and fungal SSU rRNA gene copy number and chlorophyll a concentration. Metabolic responses were measured by five ecoenzyme activities and rates of N transformation. With most measures, nutrient availability, microbial biomass, and process rates were greater in soils beneath the shrub canopy compared to the interspace between plants, and greater in the surface biocrust horizon compared to the deeper 10 cm soil profile. Most measures responded positively to experimental N addition. Effect sizes were generally greater for bulk soil than biocrust. Results were incorporated into a meta-analysis of arid ecosystem responses to N amendment that included data from 14 other studies. Effect sizes were calculated for biomass and metabolic responses. Regressions of effect sizes, calculated for biomass, and metabolic responses, showed similar trends in relation to N application rate and N load (rate × duration). The critical points separating positive from negative treatment effects were 88 kg ha-1 y-1 and 159 kg ha-1, respectively, for biomass, and 70 kg ha-1 y-1 and 114 kg ha-1, respectively, for metabolism. These critical values are comparable to those for microbial biomass, decomposition rates and respiration reported in broader meta-analyses of N amendment effects in mesic ecosystems. The large effect sizes at low N addition rates indicate that arid ecosystems are sensitive to modest increments in anthropogenic N deposition.

  16. Viscosity index improver-dispersant additive useful in oil compositions

    SciTech Connect (OSTI)

    Gardiner, J.B.; Dick, M.N.

    1988-10-25

    A process comprising grafting in the substantial absence of solvent a hydrocarbon polymer of C/sub 2/ to C/sub 28/ olefin, the polymer having a number average molecular weight in the range of about 5,000 to 500,000 with an unsaturated material selected from the group consisting of: (A) ethylenically unsaturated C/sub 3/ to C/sub 10/ carboxylic acid having 1 to 2 carboxylic acid groups or an anhydride group, and (B) nitrogen-containing ethylenically unsaturated monomers containing 6 to 30 carbon atoms and 1 to 4 nitrogen atoms, in the presence of a free radical initiator and a chain stopping agent comprising at least one member selected from the group consisting of alphatic mercaptans having 4 to 24 carbon atoms, deithyl hydroxyl amine cumene and phenols, the grafting being conducted in a manner and under conditions sufficient to form a substantially oil soluble graft copolymer useful as a viscosity index improver-dispersant additive for lubricating oil compositions.

  17. Hygroscopicity of fuels with anti-icing additives

    SciTech Connect (OSTI)

    Bedrik, B.G.; Golubushkin, V.N.; Uspenskii, S.I.

    1984-03-01

    This article investigates the accumulation of water by hydrocarbon fuels under static and dynamic conditions. Standard TS-1 fuel (aviation kerosine) is examined without an anti-icing additive (AIA) and blended with ethyl cellosolve or tetrahydrofurfuryl alcohol in the concentrations that are added to fuel before refueling flight vehicles under service conditions in order to prevent the formation of ice crystals in the fuel. The fuel hygroscopicity under static conditions is measured in desiccators over saturated salt solutions giving air relative humidities from 37% to 97% at 20/sup 0/C. It is determined that tetrahydrofurfuryl alcohol increases the fuel hygroscopicity to a greater degree than does the ethyl cellosolve. The fuel containing the AIA becomes a medium for the transfer of water from the ambient medium to the emulsion droplets, and these droplets in turn form a liquid phase. It is shown that the rate at which the fuel with the AIA becomes saturated with water under dynamic conditions is much greater than under static conditions. In the fuel without the AIA no water emulsion is formed, even with prolonged contact (more than 2 days) with 100% humidity air, whereas in the fuel with the AIA (even with 0.1% ethyl cellosolve), emulsion and liquid phase are formed. It is concluded that the physical stability of fuel containing AIA depends on the AIA concentration. Includes 3 tables.

  18. ADDITIVE TESTING FOR IMPROVED SULFUR RETENTION: PRELIMINARY REPORT

    SciTech Connect (OSTI)

    Amoroso, J.; Fox, K.

    2011-09-07

    The Savannah River National Laboratory is collaborating with Alfred University to evaluate the potential for additives in borosilicate glass to improve sulfur retention. This preliminary report provides further background on the incorporation of sulfur in glass and outlines the experiments that are being performed by the collaborators. A simulated waste glass composition has been selected for the experimental studies. The first phase of experimental work will evaluate the impacts of BaO, PbO, and V{sub 2}O{sub 5} at concentrations of 1.0, 2.0, and 5.0 wt % on sulfate retention in simulated high level waste borosilicate glass. The second phase of experimental work will evaluate the effects of time at the melt temperature on sulfur retention. The resulting samples will be characterized to determine the amount of sulfur remaining as well as to identify the formation of any crystalline phases. The results will be used to guide the future selection of frits and glass forming chemicals in vitrifying Department of Energy wastes containing high sulfur concentrations.

  19. NMR relaxometry study of plaster mortar with polymer additives

    SciTech Connect (OSTI)

    Jumate, E.; Manea, D.; Moldovan, D.; Fechete, R.

    2013-11-13

    The cement mixed with water forms a plastic paste or slurry which stiffness in time and finally hardens into a resistant stone. The addition of sand aggregates, polymers (Walocel) and/or calcium carbonate will modify dramatically the final mortar mechanic and thermal properties. The hydration processes can be observed using the 1D NMR measurements of transverse T{sub 2} relaxation times distributions analysed by a Laplace inversion algorithm. These distributions were obtained for mortar pasta measured at 2 hours after preparation then at 3, 7 and 28 days after preparation. Multiple components are identified in the T{sub 2} distributions. These can be associated with the proton bounded chemical or physical to the mortar minerals characterized by a short T{sub 2} relaxation time and to water protons in pores with three different pore sizes as observed from SEM images. The evaporation process is faster in the first hours after preparation, while the mortar hydration (bonding of water molecules to mortar minerals) can be still observed after days or months from preparation. Finally, the mechanic resistance was correlated with the transverse T{sub 2} relaxation rates corresponding to the bound water.

  20. THE HST/ACS COMA CLUSTER SURVEY. II. DATA DESCRIPTION AND SOURCE CATALOGS

    SciTech Connect (OSTI)

    Hammer, Derek; Verdoes Kleijn, Gijs; Den Brok, Mark; Peletier, Reynier F.; Hoyos, Carlos; Balcells, Marc; Aguerri, Alfonso L.; Ferguson, Henry C.; Goudfrooij, Paul; Carter, David; Guzman, Rafael; Smith, Russell J.; Lucey, John R.; Graham, Alister W.; Trentham, Neil; Peng, Eric; Puzia, Thomas H.; Jogee, Shardha; Batcheldor, Dan; Bridges, Terry J.

    2010-11-15

    The Coma cluster, Abell 1656, was the target of an HST-ACS Treasury program designed for deep imaging in the F475W and F814W passbands. Although our survey was interrupted by the ACS instrument failure in early 2007, the partially completed survey still covers {approx}50% of the core high-density region in Coma. Observations were performed for 25 fields that extend over a wide range of cluster-centric radii ({approx}1.75 Mpc or 1{sup 0}) with a total coverage area of 274 arcmin{sup 2}. The majority of the fields are located near the core region of Coma (19/25 pointings) with six additional fields in the southwest region of the cluster. In this paper, we present reprocessed images and SEXTRACTOR source catalogs for our survey fields, including a detailed description of the methodology used for object detection and photometry, the subtraction of bright galaxies to measure faint underlying objects, and the use of simulations to assess the photometric accuracy and completeness of our catalogs. We also use simulations to perform aperture corrections for the SEXTRACTOR Kron magnitudes based only on the measured source flux and its half-light radius. We have performed photometry for {approx}73,000 unique objects; approximately one-half of our detections are brighter than the 10{sigma} point-source detection limit at F814W = 25.8 mag (AB). The slight majority of objects (60%) are unresolved or only marginally resolved by ACS. We estimate that Coma members are 5%-10% of all source detections, which consist of a large population of unresolved compact sources (primarily globular clusters but also ultra-compact dwarf galaxies) and a wide variety of extended galaxies from a cD galaxy to dwarf low surface brightness galaxies. The red sequence of Coma member galaxies has a color-magnitude relation with a constant slope and dispersion over 9 mag (-21 < M {sub F814W} < -13). The initial data release for the HST-ACS Coma Treasury program was made available to the public in 2008 August. The images and catalogs described in this study relate to our second data release.