National Library of Energy BETA

Sample records for upper plate reverse

  1. An early history of pure shear in the upper plate of the raft...

    Open Energy Info (EERE)

    early history of pure shear in the upper plate of the raft river metamorphic core complex- black pine mountains, southern Idaho Jump to: navigation, search OpenEI Reference...

  2. Damage imaging in a laminated composite plate using an air-coupled time reversal mirror

    SciTech Connect (OSTI)

    Le Bas, P. -Y.; Remillieux, M. C.; Pieczonka, L.; Ten Cate, J. A.; Anderson, B. E.; Ulrich, T. J.

    2015-11-03

    We demonstrate the possibility of selectively imaging the features of a barely visible impact damage in a laminated composite plate by using an air-coupled time reversal mirror. The mirror consists of a number of piezoelectric transducers affixed to wedges of power law profiles, which act as unconventional matching layers. The transducers are enclosed in a hollow reverberant cavity with an opening to allow progressive emission of the ultrasonic wave field towards the composite plate. The principle of time reversal is used to focus elastic waves at each point of a scanning grid spanning the surface of the plate, thus allowing localized inspection at each of these points. The proposed device and signal processing removes the need to be in direct contact with the plate and reveals the same features as vibrothermography and more features than a C-scan. More importantly, this device can decouple the features of the defect according to their orientation, by selectively focusing vector components of motion into the object, through air. For instance, a delamination can be imaged in one experiment using out-of-plane focusing, whereas a crack can be imaged in a separate experiment using in-plane focusing. As a result, this capability, inherited from the principle of time reversal, cannot be found in conventional air-coupled transducers.

  3. Damage imaging in a laminated composite plate using an air-coupled time reversal mirror

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Le Bas, P. -Y.; Remillieux, M. C.; Pieczonka, L.; Ten Cate, J. A.; Anderson, B. E.; Ulrich, T. J.

    2015-11-03

    We demonstrate the possibility of selectively imaging the features of a barely visible impact damage in a laminated composite plate by using an air-coupled time reversal mirror. The mirror consists of a number of piezoelectric transducers affixed to wedges of power law profiles, which act as unconventional matching layers. The transducers are enclosed in a hollow reverberant cavity with an opening to allow progressive emission of the ultrasonic wave field towards the composite plate. The principle of time reversal is used to focus elastic waves at each point of a scanning grid spanning the surface of the plate, thus allowingmore » localized inspection at each of these points. The proposed device and signal processing removes the need to be in direct contact with the plate and reveals the same features as vibrothermography and more features than a C-scan. More importantly, this device can decouple the features of the defect according to their orientation, by selectively focusing vector components of motion into the object, through air. For instance, a delamination can be imaged in one experiment using out-of-plane focusing, whereas a crack can be imaged in a separate experiment using in-plane focusing. As a result, this capability, inherited from the principle of time reversal, cannot be found in conventional air-coupled transducers.« less

  4. Reversal of the Upper Critical Field Anisotropy and Spin-Locked

    Office of Scientific and Technical Information (OSTI)

    Superconductivity in K2Cr3As3 (Technical Report) | SciTech Connect Reversal of the Upper Critical Field Anisotropy and Spin-Locked Superconductivity in K2Cr3As3 Citation Details In-Document Search Title: Reversal of the Upper Critical Field Anisotropy and Spin-Locked Superconductivity in K2Cr3As3 Recently, superconductivity in K2Cr3As3 (Tc =6.1 K) was discovered. The crystalline lattice contains an array of weakly coupled, double well [(Cr3As3)2-]∞ linkages stretched along the c axis,

  5. Horizontal Plate Plate

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Unknown Title: Horizontal Plate Plate GeospatialDataPresentationForm: vector digital data OnlineLinkage:

  6. Nuclear reactor alignment plate configuration

    DOE Patents [OSTI]

    Altman, David A; Forsyth, David R; Smith, Richard E; Singleton, Norman R

    2014-01-28

    An alignment plate that is attached to a core barrel of a pressurized water reactor and fits within slots within a top plate of a lower core shroud and upper core plate to maintain lateral alignment of the reactor internals. The alignment plate is connected to the core barrel through two vertically-spaced dowel pins that extend from the outside surface of the core barrel through a reinforcement pad and into corresponding holes in the alignment plate. Additionally, threaded fasteners are inserted around the perimeter of the reinforcement pad and into the alignment plate to further secure the alignment plate to the core barrel. A fillet weld also is deposited around the perimeter of the reinforcement pad. To accomodate thermal growth between the alignment plate and the core barrel, a gap is left above, below and at both sides of one of the dowel pins in the alignment plate holes through with the dowel pins pass.

  7. Anisotropy reversal of the upper critical field at low temperatures and spin-locked superconductivity in K2Cr3As3

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Balakirev, F. F.; Kong, T.; Jaime, M.; McDonald, R. D.; Mielke, C. H.; Gurevich, A.; Canfield, P. C.; Bud'ko, S. L.

    2015-06-23

    We report measurements of the anisotropic upper critical field Hc2(T) for K2Cr3As3 single crystals up to 60 T and T>0.6K. Our results show that the upper critical field parallel to the Cr chains, H∥c2(T), exhibits a paramagnetically limited behavior, whereas the shape of the H⊥c2(T) curve (perpendicular to the Cr chains) has no evidence of paramagnetic effects. As a result, the curves H⊥c2(T) and H∥c2(T) cross at T≈4K, so that the anisotropy parameter γH(T)=H⊥c2/H∥c2(T)increases from γH(Tc)≈0.35 near Tc to γH(0)≈1.7 at 0.6 K. This behavior of H∥c2(T) is inconsistent with triplet superconductivity but suggests a form of singlet superconductivity withmore » the electron spins locked onto the direction of Cr chains.« less

  8. Electroless copper plating

    DOE Patents [OSTI]

    McHenry, Michael R.

    1998-12-15

    An optimized electroless copper plating technique suitable for plating electroless copper upon ceramics.

  9. Electroless copper plating

    DOE Patents [OSTI]

    McHenry, M.R.

    1998-12-15

    An optimized electroless copper plating technique is described suitable for plating electroless copper upon ceramics. 12 figs.

  10. Corrugated cover plate for flat plate collector

    DOE Patents [OSTI]

    Hollands, K. G. Terry; Sibbitt, Bruce

    1978-01-01

    A flat plate radiant energy collector is providing having a transparent cover. The cover has a V-corrugated shape which reduces the amount of energy reflected by the cover away from the flat plate absorber of the collector.

  11. Fuel cell separator plate with bellows-type sealing flanges

    DOE Patents [OSTI]

    Louis, George A. (West Hartford, CT)

    1986-08-05

    A fuel cell separator includes a rectangular flat plate having two unitary upper sealing flanges respectively comprising opposite marginal edges of the plate folded upwardly and back on themselves and two lower sealing flanges respectively comprising the other two marginal edges of the plate folded downwardly and back on themselves. Each of the sealing flanges includes a flat wall spaced from the plate and substantially parallel thereto and two accordion-pleated side walls, one of which interconnects the flat wall with the plate and the other of which stops just short of the plate, these side walls affording resilient compressibility to the sealing flange in a directiongenerally normal to the plane of the plate. Four corner members close the ends of the sealing flanges. An additional resiliently compressible reinforcing member may be inserted in the passages formed by each of the sealing flanges with the plate.

  12. Nitrided Metallic Bipolar Plates

    SciTech Connect (OSTI)

    Brady, Michael P; Toops, Todd J; Tortorelli, Peter F; More, Karren Leslie; Meyer III, Harry M; Pihl, Josh A; Wang, Heli; Turner, John; Garzon, Fernando; Rockward, Tommy; Gervasio, Don; Rakowski, Jim; EstevezGenCell, Francisco

    2010-01-01

    Effort devoted to scale up and demonstration of thin stamped metallic bipolar plates. Overall goal is to demonstrate potential for metallic bipolar plates to meet 5000 h automotive durability goal at a cost of less than $5/kW.

  13. Rotatable shear plate interferometer

    DOE Patents [OSTI]

    Duffus, Richard C.

    1988-01-01

    A rotatable shear plate interferometer comprises a transparent shear plate mounted obliquely in a tubular supporting member at 45.degree. with respect to its horizontal center axis. This tubular supporting member is supported rotatably around its center axis and a collimated laser beam is made incident on the shear plate along this center axis such that defocus in different directions can be easily measured.

  14. Plating Tank Control Software

    Energy Science and Technology Software Center (OSTI)

    1998-03-01

    The Plating Tank Control Software is a graphical user interface that controls and records plating process conditions for plating in high aspect ratio channels that require use of low current and long times. The software is written for a Pentium II PC with an 8 channel data acquisition card, and the necessary shunt resistors for measuring currents in the millampere range.

  15. Angular shear plate

    DOE Patents [OSTI]

    Ruda, Mitchell C. (Tucson, AZ); Greynolds, Alan W. (Tucson, AZ); Stuhlinger, Tilman W. (Tucson, AZ)

    2009-07-14

    One or more disc-shaped angular shear plates each include a region thereon having a thickness that varies with a nonlinear function. For the case of two such shear plates, they are positioned in a facing relationship and rotated relative to each other. Light passing through the variable thickness regions in the angular plates is refracted. By properly timing the relative rotation of the plates and by the use of an appropriate polynomial function for the thickness of the shear plate, light passing therethrough can be focused at variable positions.

  16. Pump tank divider plate for sump suction sodium pumps

    DOE Patents [OSTI]

    George, John A.; Nixon, Donald R.

    1977-01-01

    A circular plate extends across the diameter of "sump suction" pump, with a close clearance between the edge of the plate and the wall of the pump tank. The plate is located above the pump impeller, inlet and outlet flow nozzles but below the sodium free surface and effectively divides the pump tank into two separate chambers. On change of pump speed, the close fitting flow restriction plate limits the rate of flow into or out of the upper chamber, thereby minimizing the rate of level change in the tank and permitting time for the pump cover gas pressure to be varied to maintain an essentially constant level.

  17. Upper internals arrangement for a pressurized water reactor

    DOE Patents [OSTI]

    Singleton, Norman R; Altman, David A; Yu, Ching; Rex, James A; Forsyth, David R

    2013-07-09

    In a pressurized water reactor with all of the in-core instrumentation gaining access to the core through the reactor head, each fuel assembly in which the instrumentation is introduced is aligned with an upper internals instrumentation guide-way. In the elevations above the upper internals upper support assembly, the instrumentation is protected and aligned by upper mounted instrumentation columns that are part of the instrumentation guide-way and extend from the upper support assembly towards the reactor head in hue with a corresponding head penetration. The upper mounted instrumentation columns are supported laterally at one end by an upper guide tube and at the other end by the upper support plate.

  18. GOLD PLATING PROCESS

    DOE Patents [OSTI]

    Seegmiller, R.

    1957-08-01

    An improved bath is reported for plating gold on other metals. The composition of the plating bath is as follows: Gold cyanide from about 15 to about 50 grams, potassium cyanide from about 70 to about 125 grams, and sulfonated castor oil from about 0.1 to about 10 cc. The gold plate produced from this bath is smooth, semi-hard, and nonporous.

  19. Nitrided Metallic Bipolar Plates

    Broader source: Energy.gov [DOE]

    This presentation, which focuses on nitrided metallic bipolar plates, was given by M. P. Brady of ORNL at a February 2007 meeting on new fuel cell projects.

  20. PLATES WITH OXIDE INSERTS

    DOE Patents [OSTI]

    West, J.M.; Schumar, J.F.

    1958-06-10

    Planar-type fuel assemblies for nuclear reactors are described, particularly those comprising fuel in the oxide form such as thoria and urania. The fuel assembly consists of a plurality of parallel spaced fuel plate mennbers having their longitudinal side edges attached to two parallel supporting side plates, thereby providing coolant flow channels between the opposite faces of adjacent fuel plates. The fuel plates are comprised of a plurality of longitudinally extending tubular sections connected by web portions, the tubular sections being filled with a plurality of pellets of the fuel material and the pellets being thermally bonded to the inside of the tubular section by lead.

  1. Turbine vane plate assembly

    DOE Patents [OSTI]

    Schiavo Jr., Anthony L.

    2006-01-10

    A turbine vane assembly includes a turbine vane having first and second shrouds with an elongated airfoil extending between. Each end of the airfoil transitions into a shroud at a respective junction. Each of the shrouds has a plurality of cooling passages, and the airfoil has a plurality of cooling passages extending between the first and second shrouds. A substantially flat inner plate and an outer plate are coupled to each of the first and second shrouds so as to form inner and outer plenums. Each inner plenum is defined between at least the junction and the substantially flat inner plate; each outer plenum is defined between at least the substantially flat inner plate and the outer plate. Each inner plenum is in fluid communication with a respective outer plenum through at least one of the cooling passages in the respective shroud.

  2. Upper Skagit Indian Tribe

    Energy Savers [EERE]

    Feasibility of Wind to Serve Upper Skagit's Bow Hill Tribal Lands *Assess Feasibility of Residential Wind Energy Applications * * *Upper Skagit Indian Tribe is located in the Pacific Northwest , about 1 hour north of Seattle, Washington *Upper Skagit have two reservation land bases - * Bow Hill the economic land base * Helmick Road Reservation the center of government, community services & residences Skagit River & Puget Sound * Support all 5 species of salmon, steelhead * The Tribe

  3. INL HIP Plate Fabrication

    SciTech Connect (OSTI)

    B. H. Park; C. R. Clark; J. F. Jue

    2010-02-01

    This document outlines the process used to bond monolithic fuel plates by Hot Isostatic Pressing (HIP). This method was developed at Idaho National Laboratory (INL) for the Reduced Enrichment for Research and Test Reactors (RERTR) program. These foils have been used in a number of irradiation experiments in support of the United States Global Threat Reduction Initiative (GTRI) program.

  4. Reversible Acid Gas Capture

    ScienceCinema (OSTI)

    Dave Heldebrant

    2012-12-31

    Pacific Northwest National Laboratory scientist David Heldebrant demonstrates how a new process called reversible acid gas capture works to pull carbon dioxide out of power plant emissions.

  5. Renewable liquid reflecting zone plate

    DOE Patents [OSTI]

    Toor, Arthur; Ryutov, Dmitri D.

    2003-12-09

    A renewable liquid reflecting zone plate. Electrodes are operatively connected to a dielectric liquid in a circular or other arrangement to produce a reflecting zone plate. A system for renewing the liquid uses a penetrable substrate.

  6. Fuel cell plates with skewed process channels for uniform distribution of stack compression load

    DOE Patents [OSTI]

    Granata, Jr., Samuel J.; Woodle, Boyd M.

    1989-01-01

    An electrochemical fuel cell includes an anode electrode, a cathode electrode, an electrolyte matrix sandwiched between electrodes, and a pair of plates above and below the electrodes. The plate above the electrodes has a lower surface with a first group of process gas flow channels formed thereon and the plate below the electrodes has an upper surface with a second group of process gas flow channels formed thereon. The channels of each group extend generally parallel to one another. The improvement comprises the process gas flow channels on the lower surface of the plate above the anode electrode and the process gas flow channels on the upper surface of the plate below the cathode electrode being skewed in opposite directions such that contact areas of the surfaces of the plates through the electrodes are formed in crisscross arrangements. Also, the plates have at least one groove in areas of the surfaces thereof where the channels are absent for holding process gas and increasing electrochemical activity of the fuel cell. The groove in each plate surface intersects with the process channels therein. Also, the opposite surfaces of a bipolar plate for a fuel cell contain first and second arrangements of process gas flow channels in the respective surfaces which are skewed the same amount in opposite directions relative to the longitudinal centerline of the plate.

  7. Microchannel plate streak camera

    DOE Patents [OSTI]

    Wang, Ching L.

    1989-01-01

    An improved streak camera in which a microchannel plate electron multiplier is used in place of or in combination with the photocathode used in prior streak cameras. The improved streak camera is far more sensitive to photons (UV to gamma-rays) than the conventional x-ray streak camera which uses a photocathode. The improved streak camera offers gamma-ray detection with high temporal resolution. It also offers low-energy x-ray detection without attenuation inside the cathode. Using the microchannel plate in the improved camera has resulted in a time resolution of about 150 ps, and has provided a sensitivity sufficient for 1000 KeV x-rays.

  8. Microchannel plate streak camera

    DOE Patents [OSTI]

    Wang, C.L.

    1989-03-21

    An improved streak camera in which a microchannel plate electron multiplier is used in place of or in combination with the photocathode used in prior streak cameras is disclosed. The improved streak camera is far more sensitive to photons (UV to gamma-rays) than the conventional x-ray streak camera which uses a photocathode. The improved streak camera offers gamma-ray detection with high temporal resolution. It also offers low-energy x-ray detection without attenuation inside the cathode. Using the microchannel plate in the improved camera has resulted in a time resolution of about 150 ps, and has provided a sensitivity sufficient for 1,000 KeV x-rays. 3 figs.

  9. Microchannel plate streak camera

    DOE Patents [OSTI]

    Wang, C.L.

    1984-09-28

    An improved streak camera in which a microchannel plate electron multiplier is used in place of or in combination with the photocathode used in prior streak cameras. The improved streak camera is far more sensitive to photons (uv to gamma-rays) than the conventional x-ray streak camera which uses a photocathode. The improved streak camera offers gamma-ray detection with high temporal resolution. It also offers low-energy x-ray detection without attenuation inside the cathode. Using the microchannel plate in the improved camera has resulted in a time resolution of about 150 ps, and has provided a sensitivity sufficient for 1000 keV x-rays.

  10. Fuel cell end plate structure

    DOE Patents [OSTI]

    Guthrie, Robin J.; Katz, Murray; Schroll, Craig R.

    1991-04-23

    The end plates (16) of a fuel cell stack (12) are formed of a thin membrane. Pressure plates (20) exert compressive load through insulation layers (22, 26) to the membrane. Electrical contact between the end plates (16) and electrodes (50, 58) is maintained without deleterious making and breaking of electrical contacts during thermal transients. The thin end plate (16) under compressive load will not distort with a temperature difference across its thickness. Pressure plate (20) experiences a low thermal transient because it is insulated from the cell. The impact on the end plate of any slight deflection created in the pressure plate by temperature difference is minimized by the resilient pressure pad, in the form of insulation, therebetween.

  11. Channel plate for DNA sequencing

    DOE Patents [OSTI]

    Douthart, R.J.; Crowell, S.L.

    1998-01-13

    This invention is a channel plate that facilitates data compaction in DNA sequencing. The channel plate has a length, a width and a thickness, and further has a plurality of channels that are parallel. Each channel has a depth partially through the thickness of the channel plate. Additionally an interface edge permits electrical communication across an interface through a buffer to a deposition membrane surface. 15 figs.

  12. Channel plate for DNA sequencing

    DOE Patents [OSTI]

    Douthart, Richard J.; Crowell, Shannon L.

    1998-01-01

    This invention is a channel plate that facilitates data compaction in DNA sequencing. The channel plate has a length, a width and a thickness, and further has a plurality of channels that are parallel. Each channel has a depth partially through the thickness of the channel plate. Additionally an interface edge permits electrical communication across an interface through a buffer to a deposition membrane surface.

  13. Carbon-assisted flyer plates

    DOE Patents [OSTI]

    Stahl, David B.; Paisley, Dennis L.

    1994-01-01

    A laser driven flyer plate utilizing an optical fiber connected to a laser. The end of the optical fiber has a layer of carbon and a metal layer deposited onto it. The carbon layer provides the laser induced plasma which is superior to the plasma produced from most metals. The carbon layer plasma is capable of providing a flatter flyer plate, converting more of the laser energy to driving plasma, promoting a higher flyer plate acceleration, and providing a more uniform pulse behind the plate. In another embodiment, the laser is in optical communication with a substrate onto which a layer of carbon and a layer of metal have been deposited.

  14. Laser-driven flyer plate

    SciTech Connect (OSTI)

    Paisley, Dennis L.

    1991-01-01

    Apparatus for producing high velocity flyer plates involving placing a layer of dielectric material between a first metal foil and a second metal foil. With laser irradiation through an optical substrate, the first metal foil forms a plasma in the area of the irradiation, between the substrate and the solid portion of the first metal foil. When the pressure between the substrate and the foil reaches the stress limit of the dielectric, the dielectric will break away and launch the flyer plate out of the second metal foil. The mass of the flyer plate is controlled, as no portion of the flyer plate is transformed into a plasma.

  15. Laser-driven flyer plate

    SciTech Connect (OSTI)

    Paisley, D.L.

    1991-09-10

    Disclosed is an apparatus for producing high velocity flyer plates involving placing a layer of dielectric material between a first metal foil and a second metal foil. With laser irradiation through an optical substrate, the first metal foil forms a plasma in the area of the irradiation, between the substrate and the solid portion of the first metal foil. When the pressure between the substrate and the foil reaches the stress limit of the dielectric, the dielectric will break away and launch the flyer plate out of the second metal foil. The mass of the flyer plate is controlled, as no portion of the flyer plate is transformed into a plasma. 2 figures.

  16. Jacking mechanism for upper internals structure of a liquid metal nuclear reactor

    DOE Patents [OSTI]

    Gillett, James E. (Greensburg, PA); Wineman, Arthur L. (Greensburg, PA)

    1984-01-01

    A jacking mechanism for raising the upper internals structure of a liquid metal nuclear reactor which jacking mechanism uses a system of gears and drive shafts to transmit force from a single motor to four mechanically synchronized ball jacks to raise and lower support columns which support the upper internals structure. The support columns have a pin structure which rides up and down in a slot in a housing fixed to the reactor head. The pin has two locking plates which can be rotated around the pin to bring bolt holes through the locking plates into alignment with a set of bolt holes in the housing, there being a set of such housing bolt holes corresponding to both a raised and a lowered position of the support column. When the locking plate is so aligned, a surface of the locking plate mates with a surface in the housing such that the support column is then supported by the locking plate and not by the ball jacks. Since the locking plates are to be installed and bolted to the housing during periods of reactor operation, the ball jacks need not be sized to react the large forces which occur or potentially could occur on the upper internals structure of the reactor during operation. The locking plates react these loads. The ball jacks, used only during refueling, can be smaller, which enable conventionally available equipment to fulfill the precision requirements for the task within available space.

  17. Metal vapor arc ion plating

    DOE Patents [OSTI]

    Bertram, L.A.; Fisher, R.W.; Mattox, D.M.; Zanner, F.J.

    1986-09-09

    A method and apparatus for ion plating are described. The apparatus uses more negative than a first electrode voltage in a vacuum arc remelt system to attract low energy ions from the anode electrode to the article to be plated. 2 figs.

  18. Micro-channel plate detector

    DOE Patents [OSTI]

    Elam, Jeffrey W.; Lee, Seon W.; Wang, Hsien -Hau; Pellin, Michael J.; Byrum, Karen; Frisch, Henry J.

    2015-09-22

    A method and system for providing a micro-channel plate detector. An anodized aluminum oxide membrane is provided and includes a plurality of nanopores which have an Al coating and a thin layer of an emissive oxide material responsive to incident radiation, thereby providing a plurality of radiation sensitive channels for the micro-channel plate detector.

  19. Time reversal communication system

    DOE Patents [OSTI]

    Candy, James V.; Meyer, Alan W.

    2008-12-02

    A system of transmitting a signal through a channel medium comprises digitizing the signal, time-reversing the digitized signal, and transmitting the signal through the channel medium. The channel medium may be air, earth, water, tissue, metal, and/or non-metal.

  20. A Constructible and Durable High-Performance Walls System: Extended Plate

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Beam | Department of Energy A Constructible and Durable High-Performance Walls System: Extended Plate and Beam A Constructible and Durable High-Performance Walls System: Extended Plate and Beam Photo courtesy of Home Innovation Research Labs. Photo courtesy of Home Innovation Research Labs. Lead Performer: Home Innovation Research Labs-Upper Marlboro, MD Partners: American Chemistry Council, Dow Building Solutions, Forest Products Laboratory, Builders DOE Total Funding: $256,818 Cost

  1. Upper Los Alamos Canyon Cleanup

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Upper Los Alamos Canyon Cleanup Upper Los Alamos Canyon Cleanup The Upper Los Alamos Canyon Project involves cleaning up hazardous materials left over from some of the Laboratory's earliest activities. Contact Environmental Communication & Public Involvement P.O. Box 1663 MS M996 Los Alamos, NM 87545 (505) 667-0216 Email Located along Los Alamos Canyon from 7th Street to the Pajarito Ski Hill, the Upper Los Alamos Canyon Project involves examining sites in present and former Laboratory

  2. High loading uranium fuel plate

    DOE Patents [OSTI]

    Wiencek, Thomas C.; Domagala, Robert F.; Thresh, Henry R.

    1990-01-01

    Two embodiments of a high uranium fuel plate are disclosed which contain a meat comprising structured uranium compound confined between a pair of diffusion bonded ductile metal cladding plates uniformly covering the meat, the meat having a uniform high fuel loading comprising a content of uranium compound greater than about 45 Vol. % at a porosity not greater than about 10 Vol. %. In a first embodiment, the meat is a plurality of parallel wires of uranium compound. In a second embodiment, the meat is a dispersion compact containing uranium compound. The fuel plates are fabricated by a hot isostatic pressing process.

  3. The multigap resistive plate chamber

    SciTech Connect (OSTI)

    Zeballos, E. Cerron; Crotty, I.; Hatzifotiadou, D.; Valverde, J. Lamas; Neupane, S.; Williams, M. C. S.; Zichichi, A.

    2015-02-03

    The paper describes the multigap resistive plate chamber (RPC). This is a variant of the wide gap RPC. However it has much improved time resolution, while keeping all the other advantages of the wide gap RPC design.

  4. Carbon-assisted flyer plates

    DOE Patents [OSTI]

    Stahl, D.B.; Paisley, D.L.

    1994-04-12

    A laser driven flyer plate is described utilizing an optical fiber connected to a laser. The end of the optical fiber has a layer of carbon and a metal layer deposited onto it. The carbon layer provides the laser induced plasma which is superior to the plasma produced from most metals. The carbon layer plasma is capable of providing a flatter flyer plate, converting more of the laser energy to driving plasma, promoting a higher flyer plate acceleration, and providing a more uniform pulse behind the plate. In another embodiment, the laser is in optical communication with a substrate onto which a layer of carbon and a layer of metal have been deposited. 2 figures.

  5. Reversible brazing process

    DOE Patents [OSTI]

    Pierce, Jim D.; Stephens, John J.; Walker, Charles A.

    1999-01-01

    A method of reversibly brazing surfaces together. An interface is affixed to each surface. The interfaces can be affixed by processes such as mechanical joining, welding, or brazing. The two interfaces are then brazed together using a brazing process that does not defeat the surface to interface joint. Interfaces of materials such as Ni-200 can be affixed to metallic surfaces by welding or by brazing with a first braze alloy. The Ni-200 interfaces can then be brazed together using a second braze alloy. The second braze alloy can be chosen so that it minimally alters the properties of the interfaces to allow multiple braze, heat and disassemble, rebraze cycles.

  6. Reversal bending fatigue testing

    DOE Patents [OSTI]

    Wang, Jy-An John; Wang, Hong; Tan, Ting

    2014-10-21

    Embodiments for apparatuses for testing reversal bending fatigue in an elongated beam are disclosed. Embodiments are configured to be coupled to first and second end portions of the beam and to apply a bending moment to the beam and create a pure bending condition in an intermediate portion of the beam. Embodiments are further configured to cyclically alternate the direction of the bending moment applied to the beam such that the intermediate portion of the beam cyclically bends in opposite directions in a pure bending condition.

  7. Reversible Fuel Cells Workshop | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Reversible Fuel Cells Workshop Reversible Fuel Cells Workshop The National Renewable Energy Laboratory hosted a workshop addressing the current state-of-the-art of reversible fuel ...

  8. Plates for vacuum thermal fusion

    DOE Patents [OSTI]

    Davidson, James C. (Livermore, CA); Balch, Joseph W. (Livermore, CA)

    2002-01-01

    A process for effectively bonding arbitrary size or shape substrates. The process incorporates vacuum pull down techniques to ensure uniform surface contact during the bonding process. The essence of the process for bonding substrates, such as glass, plastic, or alloys, etc., which have a moderate melting point with a gradual softening point curve, involves the application of an active vacuum source to evacuate interstices between the substrates while at the same time providing a positive force to hold the parts to be bonded in contact. This enables increasing the temperature of the bonding process to ensure that the softening point has been reached and small void areas are filled and come in contact with the opposing substrate. The process is most effective where at least one of the two plates or substrates contain channels or grooves that can be used to apply vacuum between the plates or substrates during the thermal bonding cycle. Also, it is beneficial to provide a vacuum groove or channel near the perimeter of the plates or substrates to ensure bonding of the perimeter of the plates or substrates and reduce the unbonded regions inside the interior region of the plates or substrates.

  9. Insert metering plates for gas turbine nozzles

    DOE Patents [OSTI]

    Burdgick, Steven S.; Itzel, Gary; Chopra, Sanjay; Abuaf, Nesim; Correia, Victor H.

    2004-05-11

    The invention comprises a metering plate which is assembled to an impingement insert for use in the nozzle of a gas turbine. The metering plate can have one or more metering holes and is used to balance the cooling flow within the nozzle. A metering plate with multiple holes reduces static pressure variations which result from the cooling airflow through the metering plate. The metering plate can be assembled to the insert before or after the insert is inserted into the nozzle.

  10. Multiple stimulus reversible hydrogels

    DOE Patents [OSTI]

    Gutowska, Anna; Krzyminski, Karol J.

    2003-12-09

    A polymeric solution capable of gelling upon exposure to a critical minimum value of a plurality of environmental stimuli is disclosed. The polymeric solution may be an aqueous solution utilized in vivo and capable of having the gelation reversed if at least one of the stimuli fall below, or outside the range of, the critical minimum value. The aqueous polymeric solution can be used either in industrial or pharmaceutical environments. In the medical environment, the aqueous polymeric solution is provided with either a chemical or radioisotopic therapeutic agent for delivery to a specific body part. The primary advantage of the process is that exposure to one environmental stimuli alone will not cause gelation, thereby enabling the therapeutic agent to be conducted through the body for relatively long distances without gelation occurring.

  11. Multiple stimulus reversible hydrogels

    DOE Patents [OSTI]

    Gutowska, Anna; Krzyminski, Karol J.

    2006-04-25

    A polymeric solution capable of gelling upon exposure to a critical minimum value of a plurality of environmental stimuli is disclosed. The polymeric solution may be an aqueous solution utilized in vivo and capable of having the gelation reversed if at least one of the stimuli fall below, or outside the range of, the critical minimum value. The aqueous polymeric solution can be used either in industrial or pharmaceutical environments. In the medical environment, the aqueous polymeric solution is provided with either a chemical or radioisotopic therapeutic agent for delivery to a specific body part. The primary advantage of the process is that exposure to one environmental stimuli alone will not cause gelation, thereby enabling the therapeutic agent to be conducted through the body for relatively long distances without gelation occurring.

  12. Reverse Osmosis Optimization

    SciTech Connect (OSTI)

    McMordie Stoughton, Kate; Duan, Xiaoli; Wendel, Emily M.

    2013-08-26

    This technology evaluation was prepared by Pacific Northwest National Laboratory on behalf of the U.S. Department of Energys Federal Energy Management Program (FEMP). The technology evaluation assesses techniques for optimizing reverse osmosis (RO) systems to increase RO system performance and water efficiency. This evaluation provides a general description of RO systems, the influence of RO systems on water use, and key areas where RO systems can be optimized to reduce water and energy consumption. The evaluation is intended to help facility managers at Federal sites understand the basic concepts of the RO process and system optimization options, enabling them to make informed decisions during the system design process for either new projects or recommissioning of existing equipment. This evaluation is focused on commercial-sized RO systems generally treating more than 80 gallons per hour.

  13. Reverse Osmosis Optimization

    SciTech Connect (OSTI)

    2013-08-01

    This technology evaluation was prepared by Pacific Northwest National Laboratory on behalf of the U.S. Department of Energys Federal Energy Management Program (FEMP). The technology evaluation assesses techniques for optimizing reverse osmosis (RO) systems to increase RO system performance and water efficiency. This evaluation provides a general description of RO systems, the influence of RO systems on water use, and key areas where RO systems can be optimized to reduce water and energy consumption. The evaluation is intended to help facility managers at Federal sites understand the basic concepts of the RO process and system optimization options, enabling them to make informed decisions during the system design process for either new projects or recommissioning of existing equipment. This evaluation is focused on commercial-sized RO systems generally treating more than 80 gallons per hour.

  14. Reverse slapper detonator

    DOE Patents [OSTI]

    Weingart, Richard C.

    1990-01-01

    A reverse slapper detonator (70), and methodology related thereto, are provided. The detonator (70) is adapted to be driven by a pulse of electric power from an external source (80). A conductor (20) is disposed along the top (14), side (18), and bottom (16) surfaces of a sheetlike insulator (12). Part of the conductor (20) comprises a bridge (28), and an aperture (30) is positioned within the conductor (20), with the bridge (28) and the aperture (30) located on opposite sides of the insulator (12). A barrel (40) and related explosive charge (50) are positioned adjacent to and in alignment with the aperture (30), and the bridge (28) is buttressed with a backing layer (60). When the electric power pulse vaporizes the bridge (28), a portion of the insulator (12) is propelled through the aperture (30) and barrel (40), and against the explosive charge (50), thereby detonating it.

  15. Reverse photoacoustic standoff spectroscopy

    DOE Patents [OSTI]

    Van Neste, Charles W.; Senesac, Lawrence R.; Thundat, Thomas G.

    2011-04-12

    A system and method are disclosed for generating a reversed photoacoustic spectrum at a greater distance. A source may emit a beam to a target and a detector measures signals generated as a result of the beam being emitted on the target. By emitting a chopped/pulsed light beam to the target, it may be possible to determine the target's optical absorbance by monitoring the intensity of light collected at the detector at different wavelengths. As the wavelength of light is changed, the target may absorb or reject each optical frequency. Rejection may increase the intensity at the sensing element and absorption may decrease the intensity. Accordingly, an identifying spectrum of the target may be made with the intensity variation of the detector as a function of illuminating wavelength.

  16. Next Generation Bipolar Plates for Automotive PEM Fuel Cells

    SciTech Connect (OSTI)

    Orest Adrianowycz; Julian Norley; David J. Stuart; David Flaherty; Ryan Wayne; Warren Williams; Roger Tietze; Yen-Loan H. Nguyen; Tom Zawodzinski; Patrick Pietrasz

    2010-04-15

    The results of a successful U.S. Department of Energy (DoE) funded two-year $2.9 MM program lead by GrafTech International Inc. (GrafTech) are reported and summarized. The program goal was to develop the next generation of high temperature proton exchange membrane (PEM) fuel cell bipolar plates for use in transportation fuel cell applications operating at temperatures up to 120 °C. The bipolar plate composite developed during the program is based on GrafTech’s GRAFCELL resin impregnated flexible graphite technology and makes use of a high temperature Huntsman Advanced Materials resin system which extends the upper use temperature of the composite to the DoE target. High temperature performance of the new composite is achieved with the added benefit of improvements in strength, modulus, and dimensional stability over the incumbent resin systems. Other physical properties, including thermal and electrical conductivity of the new composite are identical to or not adversely affected by the new resin system. Using the new bipolar plate composite system, machined plates were fabricated and tested in high temperature single-cell fuel cells operating at 120 °C for over 1100 hours by Case Western Reserve University. Final verification of performance was done on embossed full-size plates which were fabricated and glued into bipolar plates by GrafTech. Stack testing was done on a 10-cell full-sized stack under a simulated drive cycle protocol by Ballard Power Systems. Freeze-thaw performance was conducted by Ballard on a separate 5-cell stack and shown to be within specification. A third stack was assembled and shipped to Argonne National Laboratory for independent performance verification. Manufacturing cost estimate for the production of the new bipolar plate composite at current and high volume production scenarios was performed by Directed Technologies Inc. (DTI). The production cost estimates were consistent with previous DoE cost estimates performed by DTI for the DoE on metal plates. The final result of DTI’s analysis for the high volume manufacturing scenario ($6.85 /kW) came in slightly above the DoE target of $3 to $5/kW. This estimate was derived using a “Best Case Scenario” for many of the production process steps and raw material costs with projections to high volumes. Some of the process improvements assumed in this “Best Case Scenario” including high speed high impact forming and solvent-less resins, have not yet been implemented, but have a high probability of potential success.

  17. Corrosion resistant metallic bipolar plate

    DOE Patents [OSTI]

    Brady, Michael P.; Schneibel, Joachim H.; Pint, Bruce A.; Maziasz, Philip J.

    2007-05-01

    A corrosion resistant, electrically conductive component such as a bipolar plate for a PEM fuel cell includes 20 55% Cr, balance base metal such as Ni, Fe, or Co, the component having thereon a substantially external, continuous layer of chromium nitride.

  18. Reversible micromachining locator

    DOE Patents [OSTI]

    Salzer, Leander J. (Los Alamos, NM); Foreman, Larry R. (Los Alamos, NM)

    1999-01-01

    This invention provides a device which includes a locator, a kinematic mount positioned on a conventional tooling machine, a part carrier disposed on the locator and a retainer ring. The locator has disposed therein a plurality of steel balls, placed in an equidistant position circumferentially around the locator. The kinematic mount includes a plurality of magnets which are in registry with the steel balls on the locator. In operation, a blank part to be machined is placed between a surface of a locator and the retainer ring (fitting within the part carrier). When the locator (with a blank part to be machined) is coupled to the kinematic mount, the part is thus exposed for the desired machining process. Because the locator is removably attachable to the kinematic mount, it can easily be removed from the mount, reversed, and reinserted onto the mount for additional machining. Further, the locator can likewise be removed from the mount and placed onto another tooling machine having a properly aligned kinematic mount. Because of the unique design and use of magnetic forces of the present invention, positioning errors of less than 0.25 micrometer for each machining process can be achieved.

  19. Reversible micromachining locator

    DOE Patents [OSTI]

    Salzer, L.J.; Foreman, L.R.

    1999-08-31

    This invention provides a device which includes a locator, a kinematic mount positioned on a conventional tooling machine, a part carrier disposed on the locator and a retainer ring. The locator has disposed therein a plurality of steel balls, placed in an equidistant position circumferentially around the locator. The kinematic mount includes a plurality of magnets which are in registry with the steel balls on the locator. In operation, a blank part to be machined is placed between a surface of a locator and the retainer ring (fitting within the part carrier). When the locator (with a blank part to be machined) is coupled to the kinematic mount, the part is thus exposed for the desired machining process. Because the locator is removably attachable to the kinematic mount, it can easily be removed from the mount, reversed, and reinserted onto the mount for additional machining. Further, the locator can likewise be removed from the mount and placed onto another tooling machine having a properly aligned kinematic mount. Because of the unique design and use of magnetic forces of the present invention, positioning errors of less than 0.25 micrometer for each machining process can be achieved. 7 figs.

  20. Electroless metal plating of plastics

    DOE Patents [OSTI]

    Krause, Lawrence J.

    1984-01-01

    Process for plating main group metals on aromatic polymers is carried out by the use of a nonaqueous solution of a salt of an alkali metal in a positive valence state and a main group metal in a negative valence state with contact between the solution and polymer providing a redox reaction causing the deposition of the main group metal and the reduction of the polymer. Products from the process exhibit useful decorative and electrical properties.

  1. Electroless metal plating of plastics

    DOE Patents [OSTI]

    Krause, Lawrence J.

    1986-01-01

    Process for plating main group metals on aromatic polymers is carried out by the use of a nonaqueous solution of a salt of an alkali metal in a positive valence state and a main group metal in a negative valence state with contact between the solution and polymer providing a redox reaction causing the deposition of the main group metal and the reduction of the polymer. Products from the process exhibit useful decorative and electrical properties.

  2. Electroless metal plating of plastics

    DOE Patents [OSTI]

    Krause, L.J.

    1982-09-20

    Process for plating main group metals on aromatic polymers is carried out by the use of a nonaqueous solution of a salt of an alkali metal in a positive valence state and a main group metal in a negative valence state with contact between the solution and polymer providing a redox reaction causing the deposition of the main group metal and the reduction of the polymer. Products from the process exhibit useful decorative and electrical properties.

  3. PRETREATING URANIUM FOR METAL PLATING

    DOE Patents [OSTI]

    Wehrmann, R.F.

    1961-05-01

    A process is given for anodically treating the surface of uranium articles, prior to metal plating. The metal is electrolyzed in an aqueous solution of about 10% polycarboxylic acid, preferably oxalic acid, from 1 to 5% by weight of glycerine and from 1 to 5% by weight of hydrochloric acid at from 20 to 75 deg C for from 30 seconds to 15 minutes. A current density of from 60 to 100 amperes per square foot is used.

  4. Ion plated electronic tube device

    DOE Patents [OSTI]

    Meek, T.T.

    1983-10-18

    An electronic tube and associated circuitry which is produced by ion plating techniques. The process is carried out in an automated process whereby both active and passive devices are produced at very low cost. The circuitry is extremely reliable and is capable of functioning in both high radiation and high temperature environments. The size of the electronic tubes produced are more than an order of magnitude smaller than conventional electronic tubes.

  5. CNEA Fresh Fuel Plate Characterization Summary Report

    SciTech Connect (OSTI)

    D. Keiser; F. Rice

    2012-02-01

    Characterization summary report outlining the findings of the fresh fuel examinations of the plates received from CNEA.

  6. Electrically induced mechanical precompression of ferroelectric plates

    DOE Patents [OSTI]

    Chen, Peter J.

    1987-01-01

    A method of electrically inducing mechanical precompression of a ferroelectric plate covered with electrodes utilizes the change in strains of the plate as functions of applied electric field. A first field polarizes and laterally shrinks the entire plate. An outer portion of the electrodes are removed, and an opposite field partially depolarizes and expands the central portion of the plate against the shrunk outer portion.

  7. Electrically induced mechanical precompression of ferroelectric plates

    DOE Patents [OSTI]

    Chen, P.J.

    1987-03-02

    A method of electrically inducing mechanical precompression of ferroelectric plate covered with electrodes utilizes the change in strains of the plate as functions of applied electric field. A first field polarizes and laterally shrinks the entire plate. An outer portion of the electrodes are removed, and an opposite field partially depolarizes and expands the central portion of the plate against the shrunk outer portion. 2 figs.

  8. Apparatus and method for controlling plating uniformity

    DOE Patents [OSTI]

    Hachman Jr., John T.; Kelly, James J.; West, Alan C.

    2004-10-12

    The use of an insulating shield for improving the current distribution in an electrochemical plating bath is disclosed. Numerical analysis is used to evaluate the influence of shield shape and position on plating uniformity. Simulation results are compared to experimental data for nickel deposition from a nickel--sulfamate bath. The shield is shown to improve the average current density at a plating surface.

  9. Supercritical fluid reverse micelle separation

    DOE Patents [OSTI]

    Fulton, J.L.; Smith, R.D.

    1993-11-30

    A method of separating solute material from a polar fluid in a first polar fluid phase is provided. The method comprises combining a polar fluid, a second fluid that is a gas at standard temperature and pressure and has a critical density, and a surfactant. The solute material is dissolved in the polar fluid to define the first polar fluid phase. The combined polar and second fluids, surfactant, and solute material dissolved in the polar fluid is maintained under near critical or supercritical temperature and pressure conditions such that the density of the second fluid exceeds the critical density thereof. In this way, a reverse micelle system defining a reverse micelle solvent is formed which comprises a continuous phase in the second fluid and a plurality of reverse micelles dispersed in the continuous phase. The solute material is dissolved in the polar fluid and is in chemical equilibrium with the reverse micelles. The first polar fluid phase and the continuous phase are immiscible. The reverse micelles each comprise a dynamic aggregate of surfactant molecules surrounding a core of the polar fluid. The reverse micelle solvent has a polar fluid-to-surfactant molar ratio W, which can vary over a range having a maximum ratio W[sub o] that determines the maximum size of the reverse micelles. The maximum ratio W[sub o] of the reverse micelle solvent is then varied, and the solute material from the first polar fluid phase is transported into the reverse micelles in the continuous phase at an extraction efficiency determined by the critical or supercritical conditions. 27 figures.

  10. Supercritical fluid reverse micelle separation

    DOE Patents [OSTI]

    Fulton, John L.; Smith, Richard D.

    1993-01-01

    A method of separating solute material from a polar fluid in a first polar fluid phase is provided. The method comprises combining a polar fluid, a second fluid that is a gas at standard temperature and pressure and has a critical density, and a surfactant. The solute material is dissolved in the polar fluid to define the first polar fluid phase. The combined polar and second fluids, surfactant, and solute material dissolved in the polar fluid is maintained under near critical or supercritical temperature and pressure conditions such that the density of the second fluid exceeds the critical density thereof. In this way, a reverse micelle system defining a reverse micelle solvent is formed which comprises a continuous phase in the second fluid and a plurality of reverse micelles dispersed in the continuous phase. The solute material is dissolved in the polar fluid and is in chemical equilibrium with the reverse micelles. The first polar fluid phase and the continuous phase are immiscible. The reverse micelles each comprise a dynamic aggregate of surfactant molecules surrounding a core of the polar fluid. The reverse micelle solvent has a polar fluid-to-surfactant molar ratio W, which can vary over a range having a maximum ratio W.sub.o that determines the maximum size of the reverse micelles. The maximum ratio W.sub.o of the reverse micelle solvent is then varied, and the solute material from the first polar fluid phase is transported into the reverse micelles in the continuous phase at an extraction efficiency determined by the critical or supercritical conditions.

  11. Separator plate for a fuel cell

    DOE Patents [OSTI]

    Petri, R.J.; Meek, J.; Bachta, R.P.; Marianowski, L.G.

    1996-04-02

    A separator plate is described for a fuel cell comprising an anode current collector, a cathode current collector and a main plate, the main plate disposed between the anode current collector and the cathode current collector. The anode current collector forms a flattened peripheral wet seal structure and manifold wet seal structure on the anode side of the separator plate and the cathode current collector forms a flattened peripheral wet seal structure and manifold wet seal structure on the cathode side of the separator plate. In this manner, the number of components required to manufacture and assemble a fuel cell stack is reduced. 9 figs.

  12. Separator plate for a fuel cell

    DOE Patents [OSTI]

    Petri, Randy J.; Meek, John; Bachta, Robert P.; Marianowski, Leonard G.

    1996-01-01

    A separator plate for a fuel cell comprising an anode current collector, a cathode current collector and a main plate, the main plate disposed between the anode current collector and the cathode current collector. The anode current collector forms a flattened peripheral wet seal structure and manifold wet seal structure on the anode side of the separator plate and the cathode current collector forms a flattened peripheral wet seal structure and manifold wet seal structure on the cathode side of the separator plate. In this manner, the number of components required to manufacture and assemble a fuel cell stack is reduced.

  13. Wheelspace windage cover plate for turbine

    DOE Patents [OSTI]

    Lathrop, Norman Douglas (Ballston Lake, NY)

    2002-01-01

    Windage cover plates are secured between the wheels and spacer of a turbine rotor to prevent hot flow path gas ingestion into the wheelspace cavities. Each cover plate includes a linear, axially extending body curved circumferentially with a radially outwardly directed wall at one axial end. The wall defines a axially opening recess for receiving a dovetail lug. The cover plate includes an axially extending tongue received in a circumferential groove of the spacer. The cover plate is secured with the tongue in the groove and dovetail lug in the recess. Lap joints between circumferentially adjacent cover plates are provided.

  14. Methane-derived hydrocarbons produced under upper-mantle conditions

    SciTech Connect (OSTI)

    Kolesnikov, Anton; Kutcherov, Vladimir G.; Goncharov, Alexander F.

    2009-08-13

    There is widespread evidence that petroleum originates from biological processes. Whether hydrocarbons can also be produced from abiogenic precursor molecules under the high-pressure, high-temperature conditions characteristic of the upper mantle remains an open question. It has been proposed that hydrocarbons generated in the upper mantle could be transported through deep faults to shallower regions in the Earth's crust, and contribute to petroleum reserves. Here we use in situ Raman spectroscopy in laser-heated diamond anvil cells to monitor the chemical reactivity of methane and ethane under upper-mantle conditions. We show that when methane is exposed to pressures higher than 2 GPa, and to temperatures in the range of 1,000-1,500 K, it partially reacts to form saturated hydrocarbons containing 2-4 carbons (ethane, propane and butane) and molecular hydrogen and graphite. Conversely, exposure of ethane to similar conditions results in the production of methane, suggesting that the synthesis of saturated hydrocarbons is reversible. Our results support the suggestion that hydrocarbons heavier than methane can be produced by abiogenic processes in the upper mantle.

  15. Rotation Reversal Bifurcation and Energy Confinement Saturation...

    Office of Scientific and Technical Information (OSTI)

    Rotation Reversal Bifurcation and Energy Confinement Saturation in Tokamak OhmicL-Mode Plasmas Citation Details In-Document Search Title: Rotation Reversal Bifurcation and Energy...

  16. Direct Imaging of Asymmetric Magnetization Reversal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Direct Imaging of Asymmetric Magnetization Reversal Direct Imaging of Asymmetric Magnetization Reversal Print Wednesday, 28 September 2005 00:00 The phenomenon of exchange bias has...

  17. The plate is not available in electronic format

    Office of Legacy Management (LM)

    The plate is not available in electronic format. Please email lm.records@lm.doe.gov to request the plate.

  18. Guide to Orifice Plate Steam Traps

    SciTech Connect (OSTI)

    Oland, C.B.

    2001-01-11

    This guide was prepared to serve as a foundation for making informed decisions about when orifice plate steam traps should be considered for use in new or existing steam systems. It presents background information about different types of steam traps and defines their unique functional and operational characteristics. The advantages and disadvantages associated with using orifice plate steam traps are provided to highlight their capabilities and limitations. Finally, recommendations for using orifice plate steam traps are presented, and possible applications are identified.

  19. Fuel cell cooler-humidifier plate

    DOE Patents [OSTI]

    Vitale, Nicholas G.; Jones, Daniel O.

    2000-01-01

    A cooler-humidifier plate for use in a proton exchange membrane (PEM) fuel cell stack assembly is provided. The cooler-humidifier plate combines functions of cooling and humidification within the fuel cell stack assembly, thereby providing a more compact structure, simpler manifolding, and reduced reject heat from the fuel cell. Coolant on the cooler side of the plate removes heat generated within the fuel cell assembly. Heat is also removed by the humidifier side of the plate for use in evaporating the humidification water. On the humidifier side of the plate, evaporating water humidifies reactant gas flowing over a moistened wick. After exiting the humidifier side of the plate, humidified reactant gas provides needed moisture to the proton exchange membranes used in the fuel cell stack assembly. The invention also provides a fuel cell plate that maximizes structural support within the fuel cell by ensuring that the ribs that form the boundaries of channels on one side of the plate have ends at locations that substantially correspond to the locations of ribs on the opposite side of the plate.

  20. Distribution plate for recirculating fluidized bed

    DOE Patents [OSTI]

    Yang, Wen-ching; Vidt, Edward J.; Keairns, Dale L.

    1977-01-01

    A distribution plate for a recirculating fluidized bed has a centrally disposed opening and a plurality of apertures adjacent the periphery to eliminate dead spots within the bed.

  1. Fuel cell cooler-humidifier plate

    SciTech Connect (OSTI)

    Vitale, N.G.; Jones, D.O.

    2000-05-23

    A cooler-humidifier plate for use in a proton exchange membrane (PEM) fuel cell stack assembly is provided. The cooler-humidifier plate combines functions of cooling and humidification within the fuel cell stack assembly, thereby providing a more compact structure, simpler manifolding, and reduced reject heat from the fuel cell. Coolant on the cooler side of the plate removes heat generated within the fuel cell assembly. Heat is also removed by the humidifier side of the plate for use in evaporating the humidification water. On the humidifier side of the plate, evaporating water humidifies reactant gas flowing over a moistened wick. After exiting the humidifier side of the plate, humidified reactant gas provides needed moisture to the proton exchange membranes used in the fuel cell stack assembly. The invention also provides a fuel cell plate that maximizes structural support within the fuel cell by ensuring that the ribs that form the boundaries of channels on one side of the plate have ends at locations that substantially correspond to the locations of ribs on the opposite side of the plate.

  2. Zirconium Plate Measuring Instrument (ZPMI) Design Report

    SciTech Connect (OSTI)

    K. Davies; J. H. Jackson

    2013-10-01

    This report describes the design of a device intended to measure radiation-induced strain in zirconium plate specimens as a function of neutron fluence.

  3. Nitrided Metallic Bipolar Plates | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications Nitrided Metallic Bipolar Plates Mass Production Cost Estimation for Direct H2 PEM Fuel Cell Systems for Automotive Applications: 2010 Update Mass ...

  4. Reversal of the Upper Critical Field Anisotropy and Spin-Locked...

    Office of Scientific and Technical Information (OSTI)

    Recently, superconductivity in K2Cr3As3 (Tc 6.1 K) was discovered. The crystalline lattice contains an array of weakly coupled, double well (Cr3As3)2- linkages stretched along ...

  5. Reversal of the Upper Critical Field Anisotropy and Spin-Locked...

    Office of Scientific and Technical Information (OSTI)

    Authors: Balakirev, Fedor Fedorovich 1 ; Kong, T. 2 ; Jaime, Marcelo 1 ; McDonald, Ross David 1 ; Mielke, Charles H. 1 ; Gurevich, A. 3 ; Canfield, P. C. 2 ; Bud'ko, ...

  6. Vacuum fusion bonding of glass plates

    DOE Patents [OSTI]

    Swierkowski, Steve P.; Davidson, James C.; Balch, Joseph W.

    2001-01-01

    An improved apparatus and method for vacuum fusion bonding of large, patterned glass plates. One or both glass plates are patterned with etched features such as microstructure capillaries and a vacuum pumpout moat, with one plate having at least one hole therethrough for communication with a vacuum pumpout fixture. High accuracy alignment of the plates is accomplished by a temporary clamping fixture until the start of the fusion bonding heat cycle. A complete, void-free fusion bond of seamless, full-strength quality is obtained through the plates; because the glass is heated well into its softening point and because of a large, distributed force that is developed that presses the two plates together from the difference in pressure between the furnace ambient (high pressure) and the channeling and microstructures in the plates (low pressure) due to the vacuum drawn. The apparatus and method may be used to fabricate microcapillary arrays for chemical electrophoresis; for example, any apparatus using a network of microfluidic channels embedded between plates of glass or similar moderate melting point substrates with a gradual softening point curve, or for assembly of glass-based substrates onto larger substrates, such as in flat panel display systems.

  7. Vacuum fusion bonding of glass plates

    DOE Patents [OSTI]

    Swierkowski, Steve P.; Davidson, James C.; Balch, Joseph W.

    2000-01-01

    An improved apparatus and method for vacuum fusion bonding of large, patterned glass plates. One or both glass plates are patterned with etched features such as microstructure capillaries and a vacuum pumpout moat, with one plate having at least one hole therethrough for communication with a vacuum pumpout fixture. High accuracy alignment of the plates is accomplished by a temporary clamping fixture until the start of the fusion bonding heat cycle. A complete, void-free fusion bond of seamless, full-strength quality is obtained through the plates; because the glass is heated well into its softening point and because of a large, distributed force that is developed that presses the two plates together from the difference in pressure between the furnace ambient (high pressure) and the channeling and microstructures in the plates (low pressure) due to the vacuum drawn. The apparatus and method may be used to fabricate microcapillary arrays for chemical electrophoresis; for example, any apparatus using a network of microfluidic channels embedded between plates of glass or similar moderate melting point substrates with a gradual softening point curve, or for assembly of glass-based substrates onto larger substrates, such as in flat panel display systems.

  8. Shock wave absorber having apertured plate

    DOE Patents [OSTI]

    Shin, Y.W.; Wiedermann, A.H.; Ockert, C.E.

    1983-08-26

    The shock or energy absorber disclosed herein utilizes an apertured plate maintained under the normal level of liquid flowing in a piping system and disposed between the normal liquid flow path and a cavity pressurized with a compressible gas. The degree of openness (or porosity) of the plate is between 0.01 and 0.60. The energy level of a shock wave travelling down the piping system thus is dissipated by some of the liquid being jetted through the apertured plate toward the cavity. The cavity is large compared to the quantity of liquid jetted through the apertured plate, so there is little change in its volume. The porosity of the apertured plate influences the percentage of energy absorbed.

  9. Shock wave absorber having apertured plate

    DOE Patents [OSTI]

    Shin, Yong W.; Wiedermann, Arne H.; Ockert, Carl E.

    1985-01-01

    The shock or energy absorber disclosed herein utilizes an apertured plate maintained under the normal level of liquid flowing in a piping system and disposed between the normal liquid flow path and a cavity pressurized with a compressible gas. The degree of openness (or porosity) of the plate is between 0.01 and 0.60. The energy level of a shock wave travelling down the piping system thus is dissipated by some of the liquid being jetted through the apertured plate toward the cavity. The cavity is large compared to the quantity of liquid jetted through the apertured plate, so there is little change in its volume. The porosity of the apertured plate influences the percentage of energy absorbed.

  10. Characterization of second-phase plates in a Gd5Ge3 intermetallic compound

    SciTech Connect (OSTI)

    Cao, Qing; Chumbley, Leonard S.

    2013-05-16

    Rare-earth compounds based on the stoichiometry R5(SixGe1?x)4 (R = rare-earth elements) exhibit many unusual features, including possessing R5(SixGe1?x)3 thin plates which always precipitate from the matrix despite efforts to suppress their formation. In an effort to better understand the unique relationship between these two intermetallic alloy systems, the bulk microstructure of the compound Gd5Ge3 was examined using scanning (SEM) and transmission electron microscopy (TEM) and optical microscopy. Surprisingly, SEM examination revealed a series of thin plates present in the Gd5Ge3 matrix similar to what is seen in Gd5Ge4. TEM observation revealed that a role reversal had occurred, with the thin plates possessing the orthorhombic structure and composition of Gd5Ge4. The orientation relationship between Gd5Ge4 thin plates and the Gd5Ge3 matrix was determined to be Graphic the same relationship reported for Gd5Ge3 plates precipitating from a Gd5Ge4 matrix. However, by exchanging the respective roles of the phases as regards matrix vs. precipitate, the total number of precipitation variants seen can be increased from two to six. The persistence with which these two intermetallic systems co-exist is truly unique. However, understanding exactly the kinetic and thermodynamic conditions that lead to their unique relationship is hampered by the high formation temperatures at which the observed reaction occurs.

  11. Reverse engineering of integrated circuits

    DOE Patents [OSTI]

    Chisholm, Gregory H.; Eckmann, Steven T.; Lain, Christopher M.; Veroff, Robert L.

    2003-01-01

    Software and a method therein to analyze circuits. The software comprises several tools, each of which perform particular functions in the Reverse Engineering process. The analyst, through a standard interface, directs each tool to the portion of the task to which it is most well suited, rendering previously intractable problems solvable. The tools are generally used iteratively to produce a successively more abstract picture of a circuit, about which incomplete a priori knowledge exists.

  12. Fiber optic mounted laser driven flyer plates

    DOE Patents [OSTI]

    Paisley, Dennis L. (Santa Fe, NM)

    1991-01-01

    A laser driven flyer plate where the flyer plate is deposited directly onto the squared end of an optical fiber. The plasma generated by a laser pulse drives the flyer plate toward a target. In another embodiment, a first metal layer is deposited onto the squared end of an optical fiber, followed by a layer of a dielectric material and a second metal layer. The laser pulse generates a plasma in the first metal layer, but the plasma is kept away from the second metal layer by the dielectric layer until the pressure reaches the point where shearing occurs.

  13. Effusion plate using additive manufacturing methods

    DOE Patents [OSTI]

    Johnson, Thomas Edward; Keener, Christopher Paul; Ostebee, Heath Michael; Wegerif, Daniel Gerritt

    2016-04-12

    Additive manufacturing techniques may be utilized to construct effusion plates. Such additive manufacturing techniques may include defining a configuration for an effusion plate having one or more internal cooling channels. The manufacturing techniques may further include depositing a powder into a chamber, applying an energy source to the deposited powder, and consolidating the powder into a cross-sectional shape corresponding to the defined configuration. Such methods may be implemented to construct an effusion plate having one or more channels with a curved cross-sectional geometry.

  14. Fiber optic mounted laser driven flyer plates

    SciTech Connect (OSTI)

    Paisley, D.L.

    1990-12-31

    This invention is comprised of a laser driven flyer plate where the flyer plate is deposited directly onto the squared end of an optical fiber. The plasma generated by a laser pulse drives the flyer plate toward a target. In another embodiment, a first metal layer is deposited onto the squared end of an optical fiber, followed by a layer of a dielectric material and a second metal layer. The laser pulse generates a plasma in the first metal layer, but the plasma is kept away from the second metal layer by the dielectric layer until the pressure reaches the point where shearing occurs. 2 figs.

  15. Fiber optic mounted laser driven flyer plates

    SciTech Connect (OSTI)

    Paisley, D.L.

    1991-07-09

    A laser driven flyer plate is described where the flyer plate is deposited directly onto the squared end of an optical fiber. The plasma generated by a laser pulse drives the flyer plate toward a target. In another embodiment, a first metal layer is deposited onto the squared end of an optical fiber, followed by a layer of a dielectric material and a second metal layer. The laser pulse generates a plasma in the first metal layer, but the plasma is kept away from the second metal layer by the dielectric layer until the pressure reaches the point where shearing occurs.

  16. Fiber optic mounted laser driven flyer plates

    SciTech Connect (OSTI)

    Paisley, D.L.

    1990-01-01

    This invention is comprised of a laser driven flyer plate where the flyer plate is deposited directly onto the squared end of an optical fiber. The plasma generated by a laser pulse drives the flyer plate toward a target. In another embodiment, a first metal layer is deposited onto the squared end of an optical fiber, followed by a layer of a dielectric material and a second metal layer. The laser pulse generates a plasma in the first metal layer, but the plasma is kept away from the second metal layer by the dielectric layer until the pressure reaches the point where shearing occurs. 2 figs.

  17. Review of Orifice Plate Steam Traps | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Review of Orifice Plate Steam Traps Review of Orifice Plate Steam Traps This guide was prepared to serve as a foundation for making informed decisions about when orifice plate...

  18. Amplification and reversal of Knudsen force by thermoelectric heating

    SciTech Connect (OSTI)

    O'Neill, William J.; Wada, Mizuki; Strongrich, Andrew D.; Cofer, Anthony; Alexeenko, Alina A.

    2014-12-09

    We show that the Knudsen thermal force generated by a thermally-induced flow over a heated beam near a colder wall could be amplified significantly by thermoelectric heating. Bidirectional actuation is achieved by switching the polarity of the thermoelectric device bias voltage. The measurements of the resulting thermal forces at different rarefaction regimes, realized by changing geometry and gas pressure, are done using torsional microbalance. The repulsive or attractive forces between a thermoelectrically heated or cooled plate and a substrate are shown to be up to an order of magnitude larger than for previously studied configurations and heating methods due to favorable coupling of two thermal gradients. The amplification and reversal of the Knudsen force is confirmed by numerical solution of the Boltzmann-ESBGK kinetic model equation. Because of the favorable scaling with decreasing system size, the Knudsen force with thermoelectric heating offers a novel actuation and sensing mechanism for nano/microsystems.

  19. Ponderomotive phase plate for transmission electron microscopes...

    Office of Scientific and Technical Information (OSTI)

    The system and method includes a laser source and a beam transport system to produce a focused laser crossover as a phase plate, so that a ponderomotive potential of the focused ...

  20. Characterization of Tri-lab Tantalum Plate.

    SciTech Connect (OSTI)

    Buchheit, Thomas E.; Cerreta, Ellen K.; Deibler, Lisa Anne; Chen, Shu-Rong; Michael, Joseph R.

    2014-09-01

    This report provides a detailed characterization Tri-lab Tantalum (Ta) plate jointly purchased from HCStark Inc. by Sandia, Los Alamos and Lawrence Livermore National Laboratories. Data in this report was compiled from series of material and properties characterization experiments carried out at Sandia (SNL) and Los Alamos (LANL) Laboratories through a leveraged effort funded by the C2 campaign. Results include microstructure characterization detailing the crystallographic texture of the material and an increase in grain size near the end of the rolled plate. Mechanical properties evaluations include, compression cylinder, sub-scale tension specimen, micohardness and instrumented indentation testing. The plate was found to have vastly superior uniformity when compare with previously characterized wrought Ta material. Small but measurable variations in microstructure and properties were noted at the end, and at the top and bottom edges of the plate.

  1. Upper limit on spontaneous supercurrents in Sr2RuO4

    SciTech Connect (OSTI)

    Chung, Suk Bum

    2010-04-05

    It is widely believed that the perovskite Sr{sub 2}RuO{sub 4} is an unconventional superconductor with broken time reversal symmetry. It has been predicted that superconductors with broken time reversal symmetry should have spontaneously generated supercurrents at edges and domain walls. We have done careful imaging of the magnetic fields above Sr{sub 2}RuO{sub 4} single crystals using scanning Hall bar and SQUID microscopies, and see no evidence for such spontaneously generated supercurrents. We use the results from our magnetic imaging to place upper limits on the spontaneously generated supercurrents at edges and domain walls as a function of domain size. For a single domain, this upper limit is below the predicted signal by two orders of magnitude. We speculate on the causes and implications of the lack of large spontaneous supercurrents in this very interesting superconducting system.

  2. Composite bipolar plate for electrochemical cells

    DOE Patents [OSTI]

    Wilson, Mahlon S.; Busick, Deanna N.

    2001-01-01

    A bipolar separator plate for fuel cells consists of a molded mixture of a vinyl ester resin and graphite powder. The plate serves as a current collector and may contain fluid flow fields for the distribution of reactant gases. The material is inexpensive, electrically conductive, lightweight, strong, corrosion resistant, easily mass produced, and relatively impermeable to hydrogen gas. The addition of certain fiber reinforcements and other additives can improve the properties of the composite material without significantly increasing its overall cost.

  3. Lighting system with heat distribution face plate

    DOE Patents [OSTI]

    Arik, Mehmet; Weaver, Stanton Earl; Stecher, Thomas Elliot; Kuenzler, Glenn Howard; Wolfe, Jr., Charles Franklin; Li, Ri

    2013-09-10

    Lighting systems having a light source and a thermal management system are provided. The thermal management system includes synthetic jet devices, a heat sink and a heat distribution face plate. The synthetic jet devices are arranged in parallel to one and other and are configured to actively cool the lighting system. The heat distribution face plate is configured to radially transfer heat from the light source into the ambient air.

  4. Method for plating with metal oxides

    DOE Patents [OSTI]

    Silver, Gary L. (Centerville, OH); Martin, Frank S. (Farmersville, OH)

    1994-08-23

    A method of plating hydrous metal oxides on at least one substrate, which method is indifferent to the electrochemical properties of the substrate, and comprises reacting metallic ions in aqueous solution with an appropriate oxidizing agent such as sodium hypochlorite or calcium sulfite with oxygen under suitable conditions of pH and concentration such that oxidation and precipitation of metal oxide are sufficiently slow to allow satisfactory plating of metal oxide on the substrate.

  5. Electrochemical cell and separator plate thereof

    DOE Patents [OSTI]

    Baker, Bernard S.; Dharia, Dilip J.

    1979-10-02

    A fuel cell includes a separator plate having first and second flow channels extending there through contiguously with an electrode and respectively in flow communication with the cell electrolyte and in flow isolation with respect to such electrolyte. In fuel cell system arrangement, the diverse type channels are supplied in common with process gas for thermal control purposes. The separator plate is readily formed by corrugation of integral sheet material. 10 figs.

  6. Electrochemical cell and separator plate thereof

    DOE Patents [OSTI]

    Baker, Bernard S.; Dharia, Dilip J.

    1979-01-01

    A fuel cell includes a separator plate having first and second flow channels extending therethrough contiguously with an electrode and respectively in flow communication with the cell electrolyte and in flow isolation with respect to such electrolyte. In fuel cell system arrangement, the diverse type channels are suplied in common with process gas for thermal control purposes. The separator plate is readily formed by corrugation of integral sheet material.

  7. Method for plating with metal oxides

    DOE Patents [OSTI]

    Silver, G.L.; Martin, F.S.

    1994-08-23

    A method is disclosed of plating hydrous metal oxides on at least one substrate, which method is indifferent to the electrochemical properties of the substrate, and comprises reacting metallic ions in aqueous solution with an appropriate oxidizing agent such as sodium hypochlorite or calcium sulfite with oxygen under suitable conditions of pH and concentration such that oxidation and precipitation of metal oxide are sufficiently slow to allow satisfactory plating of metal oxide on the substrate. 1 fig.

  8. Plate Tectonics, Geographical Information System, paleogeography

    Energy Science and Technology Software Center (OSTI)

    2002-05-24

    The PaleoX.framwork is a dynamically linked/loaded framework for Cocoa applications. The primary goal of this library is to standardize several elements used for working with paleogeographic data. This includes objects designed to organize information for tectonic plates, including maps, rotation objects, plate names, and designations. In addition, PaleoX provides object-oriented solutions for handling standard paleogeographic file formats from the PALEOMAP Project.

  9. REVERSE RADIATIVE SHOCK LASER EXPERIMENTS RELEVANT TO ACCRETING STREAM-DISK IMPACT IN INTERACTING BINARIES

    SciTech Connect (OSTI)

    Krauland, C. M.; Drake, R. P.; Kuranz, C. C.; Huntington, C. M.; Kaczala, D. N.; Klein, S.; Sweeney, R.; Young, R. P.; Keiter, P. A.; Loupias, B.; Falize, E.; Villette, B.; Plewa, T. E-mail: rpdrake@umich.edu

    2013-01-01

    We present the first results from high-energy-density laboratory astrophysics experiments that explore the hydrodynamic and radiative properties of a reverse shock relevant to a cataclysmic variable system. A reverse shock is a shock wave that develops when a freely flowing, supersonic plasma is impeded. In our experiments, performed on the Omega Laser Facility, a laser pulse is used to accelerate plasma ejecta into a vacuum. This flow is directed into an Al plate in front of which a shock forms in the rebounding plasma. The plasma flow is moving fast enough that it is shocked to high enough temperatures that radiative cooling affects the shock structure. These are the first experiments to produce a radiative reverse shock wave.

  10. Remote Whispering Applying Time Reversal

    SciTech Connect (OSTI)

    Anderson, Brian Eric

    2015-07-16

    The purpose of this project was to explore the use of time reversal technologies as a means for communication to a targeted individual or location. The idea is to have the privacy of whispering in one’s ear, but to do this remotely from loudspeakers not located near the target. Applications of this work include communicating with hostages and survivors in rescue operations, communicating imaging and operational conditions in deep drilling operations, monitoring storage of spent nuclear fuel in storage casks without wires, or clandestine activities requiring signaling between specific points. This technology provides a solution in any application where wires and radio communications are not possible or not desired. It also may be configured to self calibrate on a regular basis to adjust for changing conditions. These communications allow two people to converse with one another in real time, converse in an inaudible frequency range or medium (i.e. using ultrasonic frequencies and/or sending vibrations through a structure), or send information for a system to interpret (even allowing remote control of a system using sound). The time reversal process allows one to focus energy to a specific location in space and to send a clean transmission of a selected signal only to that location. In order for the time reversal process to work, a calibration signal must be obtained. This signal may be obtained experimentally using an impulsive sound, a known chirp signal, or other known signals. It may also be determined from a numerical model of a known environment in which the focusing is desired or from passive listening over time to ambient noise.

  11. Corrosion test cell for bipolar plates

    DOE Patents [OSTI]

    Weisbrod, Kirk R.

    2002-01-01

    A corrosion test cell for evaluating corrosion resistance in fuel cell bipolar plates is described. The cell has a transparent or translucent cell body having a pair of identical cell body members that seal against opposite sides of a bipolar plate. The cell includes an anode chamber and an cathode chamber, each on opposite sides of the plate. Each chamber contains a pair of mesh platinum current collectors and a catalyst layer pressed between current collectors and the plate. Each chamber is filled with an electrolyte solution that is replenished with fluid from a much larger electrolyte reservoir. The cell includes gas inlets to each chamber for hydrogen gas and air. As the gases flow into a chamber, they pass along the platinum mesh, through the catalyst layer, and to the bipolar plate. The gas exits the chamber through passageways that provide fluid communication between the anode and cathode chambers and the reservoir, and exits the test cell through an exit port in the reservoir. The flow of gas into the cell produces a constant flow of fresh electrolyte into each chamber. Openings in each cell body is member allow electrodes to enter the cell body and contact the electrolyte in the reservoir therein. During operation, while hydrogen gas is passed into one chamber and air into the other chamber, the cell resistance is measured, which is used to evaluate the corrosion properties of the bipolar plate.

  12. Rotary sequencing valve with flexible port plate

    DOE Patents [OSTI]

    Wagner, Glenn Paul

    2005-05-10

    Rotary sequencing valve comprising a rotor having a rotor face rotatable about an axis perpendicular to the rotor face, wherein the rotor face has a plurality of openings, one or more of which are disposed at a selected radial distance from the axis, and wherein the rotor includes at least one passage connecting at least one pair of the plurality of openings. The valve includes a flexible port plate having a first side and a second side, wherein the first side faces the rotor and engages the rotor such that the flexible port plate can be rotated coaxially by the rotor and can move axially with respect to the rotor, wherein the flexible port plate has a plurality of ports between the first and second sides, which ports are aligned with the openings in the rotor face. The valve also includes a stator having a stator face disposed coaxially with the rotor and the flexible port plate, wherein the second side of the flexible port plate is in sealable, slidable rotary contact with the stator face, wherein the stator face has a plurality of openings, some of which are disposed at the selected radial distance from the axis, and wherein the plurality of openings extend as passages through the stator. The valve may be used in pressure or temperature swing adsorption systems.

  13. Recovery process for electroless plating baths

    DOE Patents [OSTI]

    Anderson, R.W.; Neff, W.A.

    1992-05-12

    A process is described for removing, from spent electroless metal plating bath solutions, accumulated byproducts and counter-ions that have deleterious effects on plating. The solution, or a portion thereof, is passed through a selected cation exchange resin bed in hydrogen form, the resin selected from strong acid cation exchangers and combinations of intermediate acid cation exchangers with strong acid cation exchangers. Sodium and nickel ions are sorbed in the selected cation exchanger, with little removal of other constituents. The remaining solution is subjected to sulfate removal through precipitation of calcium sulfate hemihydrate using, sequentially, CaO and then CaCO[sub 3]. Phosphite removal from the solution is accomplished by the addition of MgO to form magnesium phosphite trihydrate. The washed precipitates of these steps can be safely discarded in nontoxic land fills, or used in various chemical industries. Finally, any remaining solution can be concentrated, adjusted for pH, and be ready for reuse. The plating metal can be removed from the exchanger with sulfuric acid or with the filtrate from the magnesium phosphite precipitation forming a sulfate of the plating metal for reuse. The process is illustrated as applied to processing electroless nickel plating baths. 18 figs.

  14. Recovery process for electroless plating baths

    DOE Patents [OSTI]

    Anderson, Roger W.; Neff, Wayne A.

    1992-01-01

    A process for removing, from spent electroless metal plating bath solutions, accumulated byproducts and counter-ions that have deleterious effects on plating. The solution, or a portion thereof, is passed through a selected cation exchange resin bed in hydrogen form, the resin selected from strong acid cation exchangers and combinations of intermediate acid cation exchangers with strong acid cation exchangers. Sodium and nickel ions are sorbed in the selected cation exchanger, with little removal of other constituents. The remaining solution is subjected to sulfate removal through precipitation of calcium sulfate hemihydrate using, sequentially, CaO and then CaCO.sub.3. Phosphite removal from the solution is accomplished by the addition of MgO to form magnesium phosphite trihydrate. The washed precipitates of these steps can be safely discarded in nontoxic land fills, or used in various chemical industries. Finally, any remaining solution can be concentrated, adjusted for pH, and be ready for reuse. The plating metal can be removed from the exchanger with sulfuric acid or with the filtrate from the magnesium phosphite precipitation forming a sulfate of the plating metal for reuse. The process is illustrated as applied to processing electroless nickel plating baths.

  15. Process of forming compounds using reverse micelle or reverse microemulsion systems

    DOE Patents [OSTI]

    Linehan, John C.; Fulton, John L.; Bean, Roger M.

    1998-01-01

    The present invention is directed to a process for producing a nanometer-sized metal compound. The process comprises forming a reverse micelle or reverse microemulsion system comprising a polar fluid in a non-polar or low-polarity fluid. A first reactant comprising a multi-component, water-soluble metal compound is introduced into the polar fluid in a non-polar or low-polarity fluid. This first reactant can be introduced into the reverse micelle or reverse microemulsion system during formation thereof or subsequent to the formation of the reverse micelle or microemulsion system. The water-soluble metal compound is then reacted in the reverse micelle or reverse microemulsion system to form the nanometer-sized metal compound. The nanometer-sized metal compound is then precipitated from the reverse micelle or reverse microemulsion system.

  16. Highly conductive composites for fuel cell flow field plates and bipolar plates

    DOE Patents [OSTI]

    Jang, Bor Z; Zhamu, Aruna; Song, Lulu

    2014-10-21

    This invention provides a fuel cell flow field plate or bipolar plate having flow channels on faces of the plate, comprising an electrically conductive polymer composite. The composite is composed of (A) at least 50% by weight of a conductive filler, comprising at least 5% by weight reinforcement fibers, expanded graphite platelets, graphitic nano-fibers, and/or carbon nano-tubes; (B) polymer matrix material at 1 to 49.9% by weight; and (C) a polymer binder at 0.1 to 10% by weight; wherein the sum of the conductive filler weight %, polymer matrix weight % and polymer binder weight % equals 100% and the bulk electrical conductivity of the flow field or bipolar plate is at least 100 S/cm. The invention also provides a continuous process for cost-effective mass production of the conductive composite-based flow field or bipolar plate.

  17. Microporous microchannel plates and method of manufacturing same

    DOE Patents [OSTI]

    Beetz, Jr., Charles P.; Boerstler, Robert W.; Steinbeck, John; Winn, David R.

    2000-01-01

    A microchannel plate and method of manufacturing same is provided. The microchannel plate includes a plate consisting of an anodized material and a plurality of channels which are formed during the anodization of the material and extend between the two sides of the plate. Electrodes are also disposed on each side of the plate for generating an electrical field within the channels. Preferably, the material is alumina and the channels are activated such that the channel walls are conductive and highly secondary emissive.

  18. Time Reversal of Bose-Einstein Condensates

    SciTech Connect (OSTI)

    Martin, J.; Georgeot, B.; Shepelyansky, D. L. [Laboratoire de Physique Theorique, Universite de Toulouse III, CNRS, 31062 Toulouse (France)

    2008-08-15

    Using Gross-Pitaevskii equation, we study the time reversibility of Bose-Einstein condensates (BEC) in kicked optical lattices, showing that in the regime of quantum chaos, the dynamics can be inverted from explosion to collapse. The accuracy of time reversal decreases with the increase of atom interactions in BEC, until it is completely lost. Surprisingly, quantum chaos helps to restore time reversibility. These predictions can be tested with existing experimental setups.

  19. Reverse Osmosis Optimization | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Reverse Osmosis Optimization Reverse Osmosis Optimization Report assesses techniques for optimizing reverse osmosis (RO) systems to increase RO system performance and water efficiency. It provides a general description of RO systems, the influence of RO systems on water use, and key areas where RO systems can be optimized to reduce water and energy consumption. This report is intended to help facility managers at Federal sites understand the basic concepts of the RO process and system

  20. Direct Imaging of Asymmetric Magnetization Reversal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Direct Imaging of Asymmetric Magnetization Reversal Direct Imaging of Asymmetric Magnetization Reversal Print Wednesday, 28 September 2005 00:00 The phenomenon of exchange bias has transformed how data is read on magnetic hard disks and created an explosion in their information storage density. However, it remains poorly understood, and even the fundamental mechanism of magnetic reversal for exchange-biased systems in changing magnetic fields is unclear. By using x-ray photoemission electron

  1. Gravity controlled anti-reverse rotation device

    DOE Patents [OSTI]

    Dickinson, Robert J.; Wetherill, Todd M.

    1983-01-01

    A gravity assisted anti-reverse rotation device for preventing reverse rotation of pumps and the like. A horizontally mounted pawl is disposed to mesh with a fixed ratchet preventing reverse rotation when the pawl is advanced into intercourse with the ratchet by a vertically mounted lever having a lumped mass. Gravitation action on the lumped mass urges the pawl into mesh with the ratchet, while centrifugal force on the lumped mass during forward, allowed rotation retracts the pawl away from the ratchet.

  2. Ponderomotive phase plate for transmission electron microscopes

    DOE Patents [OSTI]

    Reed, Bryan W. (Livermore, CA)

    2012-07-10

    A ponderomotive phase plate system and method for controllably producing highly tunable phase contrast transfer functions in a transmission electron microscope (TEM) for high resolution and biological phase contrast imaging. The system and method includes a laser source and a beam transport system to produce a focused laser crossover as a phase plate, so that a ponderomotive potential of the focused laser crossover produces a scattering-angle-dependent phase shift in the electrons of the post-sample electron beam corresponding to a desired phase contrast transfer function.

  3. Cascade impactor and jet plate for same

    DOE Patents [OSTI]

    Dahlin, Robert S.; Farthing, William E.; Landham Jr., Edward C.

    2004-02-03

    A sampling system and method for sampling particulate matter from a high-temperature, high-pressure gas stream. A cyclone sampler for use at high temperatures and pressures, and having threadless sacrificial connectors is disclosed. Also disclosed is an improved cascade impactor including jet plates with integral spacers, and alignment features provided for aligning the jet plates with their associated collection substrates. An activated bauxite alkali collector is disclosed, and includes an alumina liner. The sampling system can be operated remotely or locally, and can be permanently installed or configured as a portable system.

  4. Direct Imaging of Asymmetric Magnetization Reversal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Direct Imaging of Asymmetric Magnetization Reversal Print The phenomenon of exchange bias has transformed how data is read on magnetic hard disks and created an explosion in their...

  5. Titanium carbide bipolar plate for electrochemical devices

    DOE Patents [OSTI]

    LaConti, Anthony B.; Griffith, Arthur E.; Cropley, Cecelia C.; Kosek, John A.

    2000-07-04

    A corrosion resistant, electrically conductive, non-porous bipolar plate is made from titanium carbide for use in an eletrochemical device. The process involves blending titanium carbide powder with a suitable binder material, and molding the mixture, at an elevated temperature and pressure.

  6. Magnetically excited flexural plate wave apparatus

    DOE Patents [OSTI]

    Martin, Stephen J.; Butler, Michael A.; Frye, Gregory C.; Smith, James H.

    1998-01-01

    A non-piezoelectric flexural plate wave apparatus having meander-line transducers mounted on a non-piezoelectric membrane. A static magnetic field is directed perpendicularly to the conductive legs of the transducers in the plane of the membrane. Single-port, two-port, resonant, non-resonant, eigenmode, and delay-line modes may be employed.

  7. Magnetically excited flexural plate wave apparatus

    DOE Patents [OSTI]

    Martin, S.J.; Butler, M.A.; Frye, G.C.; Smith, J.H.

    1998-11-17

    A non-piezoelectric flexural plate wave apparatus having meander-line transducers mounted on a non-piezoelectric membrane is disclosed. A static magnetic field is directed perpendicularly to the conductive legs of the transducers in the plane of the membrane. Single-port, two-port, resonant, non-resonant, eigenmode, and delay-line modes may be employed. 15 figs.

  8. Brazed bipolar plates for PEM fuel cells

    DOE Patents [OSTI]

    Neutzler, Jay Kevin

    1998-01-01

    A liquid-cooled, bipolar plate separating adjacent cells of a PEM fuel cell comprising corrosion-resistant metal sheets brazed together so as to provide a passage between the sheets through which a dielectric coolant flows. The brazement comprises a metal which is substantially insoluble in the coolant.

  9. Brazed bipolar plates for PEM fuel cells

    DOE Patents [OSTI]

    Neutzler, J.K.

    1998-07-07

    A liquid-cooled, bipolar plate separating adjacent cells of a PEM fuel cell comprises corrosion-resistant metal sheets brazed together so as to provide a passage between the sheets through which a dielectric coolant flows. The brazement comprises a metal which is substantially insoluble in the coolant. 6 figs.

  10. Plate forming and break down pizza box

    DOE Patents [OSTI]

    Pantisano, Frank; Devine, Scott M.

    1992-01-01

    A standard corrugated paper pizza box is provided with slit cuts cut through the top panel of the pizza box in a shape to form four circular serving plates with a beveled raised edge and cross slit cuts through the bottom panel of the pizza box separating the box into four essentially equal portions for easy disposal.

  11. Fuel cell system with coolant flow reversal

    DOE Patents [OSTI]

    Kothmann, Richard E. (Pittsburgh, PA)

    1986-01-01

    Method and apparatus for cooling electrochemical fuel cell system components. Periodic reversal of the direction of flow of cooling fluid through a fuel cell stack provides greater uniformity and cell operational temperatures. Flow direction through a recirculating coolant fluid circuit is reversed through a two position valve, without requiring modulation of the pumping component.

  12. Three component vibrational time reversal communication

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Anderson, Brian E.; Ulrich, Timothy J.; Ten Cate, James A.

    2015-01-01

    Time reversal provides an optimal prefilter matched signal to apply to a communication signal before signal transmission. Time reversal allows compensation for wave speed dispersion and can function well in reverberant environments. Time reversal can be used to focus elastic energy to each of the three components of motion independently. A pipe encased in concrete was used to demonstrate the ability to conduct communications of information using three component time reversal. Furthermore, the ability of time reversal to compensate for multi-path distortion (overcoming reverberation) will be demonstrated and the rate of signal communication will be presented. [The U.S. Department ofmore » Energy, through the LANL/LDRD Program, is gratefully acknowledged for supporting this work.]« less

  13. Fuel cell plates with improved arrangement of process channels for enhanced pressure drop across the plates

    DOE Patents [OSTI]

    Spurrier, Francis R.; Pierce, Bill L.; Wright, Maynard K.

    1986-01-01

    A plate for a fuel cell has an arrangement of ribs defining an improved configuration of process gas channels and slots on a surface of the plate which provide a modified serpentine gas flow pattern across the plate surface. The channels are generally linear and arranged parallel to one another while the spaced slots allow cross channel flow of process gas in a staggered fashion which creates a plurality of generally mini-serpentine flow paths extending transverse to the longitudinal gas flow along the channels. Adjacent pairs of the channels are interconnected to one another in flow communication. Also, a bipolar plate has the aforementioned process gas channel configuration on one surface and another configuration on the opposite surface. In the other configuration, there are not slots and the gas flow channels have a generally serpentine configuration.

  14. Chemical reactions in reverse micelle systems

    DOE Patents [OSTI]

    Matson, Dean W.; Fulton, John L.; Smith, Richard D.; Consani, Keith A.

    1993-08-24

    This invention is directed to conducting chemical reactions in reverse micelle or microemulsion systems comprising a substantially discontinuous phase including a polar fluid, typically an aqueous fluid, and a microemulsion promoter, typically a surfactant, for facilitating the formation of reverse micelles in the system. The system further includes a substantially continuous phase including a non-polar or low-polarity fluid material which is a gas under standard temperature and pressure and has a critical density, and which is generally a water-insoluble fluid in a near critical or supercritical state. Thus, the microemulsion system is maintained at a pressure and temperature such that the density of the non-polar or low-polarity fluid exceeds the critical density thereof. The method of carrying out chemical reactions generally comprises forming a first reverse micelle system including an aqueous fluid including reverse micelles in a water-insoluble fluid in the supercritical state. Then, a first reactant is introduced into the first reverse micelle system, and a chemical reaction is carried out with the first reactant to form a reaction product. In general, the first reactant can be incorporated into, and the product formed in, the reverse micelles. A second reactant can also be incorporated in the first reverse micelle system which is capable of reacting with the first reactant to form a product.

  15. Next Generation Bipolar Plates for Automotive PEM Fuel Cells...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Next Generation Bipolar Plates for Automotive PEM Fuel Cells Next Generation Bipolar Plates for Automotive PEM Fuel Cells Part of a 100 million fuel cell award announced by DOE ...

  16. Flat-Plate Photovoltaic Balance of System Basics | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Flat-Plate Photovoltaic Balance of System Basics Flat-Plate Photovoltaic Balance of System Basics August 20, 2013 - 4:29pm Addthis Complete photovoltaic (PV) energy systems are ...

  17. Fast microchannel plate detector for particles

    SciTech Connect (OSTI)

    Wurz, P.; Gubler, L.

    1996-05-01

    In this article we report on the timing capabilities of a new microchannel plate detector we designed and built. The detector assembly has an impedance-matched transition line (50 {Omega} line resistance) from anode to cable connector which is considerably smaller than other, commercially available solutions and at the same time has about four times the active area. The detector was tested with an alpha particle source and excellent time response was achieved. Using 10 {mu}m pore size channel plates, a rise time of 300 ps and a pulse width of 520 ps are obtained. The details of the signal analysis are also given in the article. {copyright} {ital 1996 American Institute of Physics.}

  18. Cheaper Adjoints by Reversing Address Computations

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Hascoët, L.; Utke, J.; Naumann, U.

    2008-01-01

    The reverse mode of automatic differentiation is widely used in science and engineering. A severe bottleneck for the performance of the reverse mode, however, is the necessity to recover certain intermediate values of the program in reverse order. Among these values are computed addresses, which traditionally are recovered through forward recomputation and storage in memory. We propose an alternative approach for recovery that uses inverse computation based on dependency information. Address storage constitutes a significant portion of the overall storage requirements. An example illustrates substantial gains that the proposed approach yields, and we show use cases in practical applications.

  19. Review of Orifice Plate Steam Traps | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Review of Orifice Plate Steam Traps Review of Orifice Plate Steam Traps This guide was prepared to serve as a foundation for making informed decisions about when orifice plate steam traps should be considered for use in new or existing steam systems. It presents background information about different types of steam traps and defines their unique functional and operational characteristics. The advantages and disadvantages associated with using orifice plate steam traps are provided to highlight

  20. ELAF failed fuel plate examination. [Extended Life Aluminide Fuel

    SciTech Connect (OSTI)

    Beeston, J.M.; Miller, L.G.; Brown, K.R.; McGinty, D.M.

    1984-10-01

    A fuel plate examination was conducted in the hot cell and canal to determine the possible failure modes for three plates leaking fission products. The plates were irradiated in the Extended Life Aluminide Fuel (ELAF) program in support of university research reactor goals to increase the limits presently allowed. The examination indicated pitting corrosion to be the failure mode. Other failure modes such as: (a) nonbonded swelling, (b) excessive fuel swelling, and (c) overheating of the plates were not observed.

  1. Variable thickness double-refracting plate

    DOE Patents [OSTI]

    Hadeishi, Tetsuo

    1976-01-01

    This invention provides an A.C., cyclic, current-controlled, phase retardation plate that uses a magnetic clamp to produce stress birefringence. It was developed for an Isotope-Zeeman Atomic Absorption Spectrometer that uses polarization modulation to effect automatic background correction in atomic absorption trace-element measurements. To this end, the phase retardation plate of the invention is a variable thickness, photoelastic, double-refracting plate that is alternately stressed and released by the magnetic clamp selectively to modulate specific components selected from the group consisting of circularly and plane polarized Zeeman components that are produced in a dc magnetic field so that they correspond respectively to Zeeman reference and transmission-probe absorption components. The polarization modulation changes the phase of these polarized Zeeman components, designated as .sigma. reference and .pi. absorption components, so that every half cycle the components change from a transmission mode to a mode in which the .pi. component is blocked and the .sigma. components are transmitted. Thus, the Zeeman absorption component, which corresponds in amplitude to the amount of the trace element to be measured in a sample, is alternately transmitted and blocked by a linear polarizer, while the circularly polarized reference components are continuously transmitted thereby. The result is a sinusoidally varying output light amplitude whose average corresponds to the amount of the trace element present in the sample.

  2. ON COMPUTING UPPER LIMITS TO SOURCE INTENSITIES

    SciTech Connect (OSTI)

    Kashyap, Vinay L.; Siemiginowska, Aneta [Smithsonian Astrophysical Observatory, 60 Garden Street, Cambridge, MA 02138 (United States); Van Dyk, David A.; Xu Jin [Department of Statistics, University of California, Irvine, CA 92697-1250 (United States); Connors, Alanna [Eureka Scientific, 2452 Delmer Street, Suite 100, Oakland, CA 94602-3017 (United States); Freeman, Peter E. [Department of Statistics, Carnegie Mellon University, 5000 Forbes Avenue, Pittsburgh, PA 15213 (United States); Zezas, Andreas, E-mail: vkashyap@cfa.harvard.ed, E-mail: asiemiginowska@cfa.harvard.ed, E-mail: dvd@ics.uci.ed, E-mail: jinx@ics.uci.ed, E-mail: aconnors@eurekabayes.co, E-mail: pfreeman@cmu.ed, E-mail: azezas@cfa.harvard.ed [Physics Department, University of Crete, P.O. Box 2208, GR-710 03, Heraklion, Crete (Greece)

    2010-08-10

    A common problem in astrophysics is determining how bright a source could be and still not be detected in an observation. Despite the simplicity with which the problem can be stated, the solution involves complicated statistical issues that require careful analysis. In contrast to the more familiar confidence bound, this concept has never been formally analyzed, leading to a great variety of often ad hoc solutions. Here we formulate and describe the problem in a self-consistent manner. Detection significance is usually defined by the acceptable proportion of false positives (background fluctuations that are claimed as detections, or Type I error), and we invoke the complementary concept of false negatives (real sources that go undetected, or Type II error), based on the statistical power of a test, to compute an upper limit to the detectable source intensity. To determine the minimum intensity that a source must have for it to be detected, we first define a detection threshold and then compute the probabilities of detecting sources of various intensities at the given threshold. The intensity that corresponds to the specified Type II error probability defines that minimum intensity and is identified as the upper limit. Thus, an upper limit is a characteristic of the detection procedure rather than the strength of any particular source. It should not be confused with confidence intervals or other estimates of source intensity. This is particularly important given the large number of catalogs that are being generated from increasingly sensitive surveys. We discuss, with examples, the differences between these upper limits and confidence bounds. Both measures are useful quantities that should be reported in order to extract the most science from catalogs, though they answer different statistical questions: an upper bound describes an inference range on the source intensity, while an upper limit calibrates the detection process. We provide a recipe for computing upper limits that applies to all detection algorithms.

  3. Preliminary Measurements From A New Flat Plate Facility For Aerodynamic Research

    SciTech Connect (OSTI)

    D. M. McEligot; D. W. Nigg; E. J. Walsh; D. Hernon; M.R.D. Davies

    2005-03-01

    This paper details the design and preliminary measurements used in the characterisation of a new flat plate research facility. The facility is designed specifically to aid in the understanding of entropy generation throughout the boundary layer with special attention given to non-equilibrium flows. Hot-wire measurements were obtained downstream of two turbulence generating grids. The turbulence intensity, integral and dissipation length scale ranges measured are 1.6%-7%, 5mm-17mm and 0.7mm-7mm, respectively. These values compared well to existing correlations. The flow downstream of both grids was found to be homogenous and isotropic. Flow visualisation is employed to determine aerodynamic parameters such as flow 2-dimensionality and the effect of the flap angle on preventing separation at the leading edge. The flow was found to be 2-dimensional over all measurement planes. The non-dimensional pressure distribution of a modern turbine blade suction surface is simulated on the flat plate through the use of a variable upper wall. The Reynolds number range based on wetted plate length and inlet velocity is 70,000-4,000,000.

  4. Upper Division Hot Spring Geothermal Area | Open Energy Information

    Open Energy Info (EERE)

    Upper Division Hot Spring Geothermal Area Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Upper Division Hot Spring Geothermal Area Contents 1 Area Overview 2 History...

  5. Reversing the Circulation of Magnetic Vortices

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reversing the Circulation of Magnetic Vortices Print In magnetic media, information is stored in binary form-one or zero, depending on which way the electronic spins are aligned in...

  6. Direct Imaging of Asymmetric Magnetization Reversal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and H. Ohldag, "Direct imaging of asymmetric magnetization reversal in exchange-biased FeMnPd bilayers by x-ray photoemission electron microscopy," Phys. Rev. Lett. 94, 107203...

  7. Direct Imaging of Asymmetric Magnetization Reversal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    H. Ohldag, "Direct imaging of asymmetric magnetization reversal in exchange-biased FeMnPd bilayers by x-ray photoemission electron microscopy," Phys. Rev. Lett. 94, 107203 (2005...

  8. Direct Imaging of Asymmetric Magnetization Reversal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Direct Imaging of Asymmetric Magnetization Reversal Print The phenomenon of exchange bias has transformed how data is read on magnetic hard disks and created an explosion in their information storage density. However, it remains poorly understood, and even the fundamental mechanism of magnetic reversal for exchange-biased systems in changing magnetic fields is unclear. By using x-ray photoemission electron microscopy at the ALS to directly image the magnetic structure of an exchange-biased film,

  9. Reversing the Circulation of Magnetic Vortices

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reversing the Circulation of Magnetic Vortices Reversing the Circulation of Magnetic Vortices Print Wednesday, 31 July 2013 00:00 In magnetic media, information is stored in binary form-one or zero, depending on which way the electronic spins are aligned in a given section of the medium. Recently, however, magnetic vortices have drawn scientists toward a new possibility: multibit storage in which each logic unit has four states instead of two and can store twice the information. Each tiny

  10. Direct Imaging of Asymmetric Magnetization Reversal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Direct Imaging of Asymmetric Magnetization Reversal Print The phenomenon of exchange bias has transformed how data is read on magnetic hard disks and created an explosion in their information storage density. However, it remains poorly understood, and even the fundamental mechanism of magnetic reversal for exchange-biased systems in changing magnetic fields is unclear. By using x-ray photoemission electron microscopy at the ALS to directly image the magnetic structure of an exchange-biased film,

  11. Direct Imaging of Asymmetric Magnetization Reversal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Direct Imaging of Asymmetric Magnetization Reversal Print The phenomenon of exchange bias has transformed how data is read on magnetic hard disks and created an explosion in their information storage density. However, it remains poorly understood, and even the fundamental mechanism of magnetic reversal for exchange-biased systems in changing magnetic fields is unclear. By using x-ray photoemission electron microscopy at the ALS to directly image the magnetic structure of an exchange-biased film,

  12. Direct Imaging of Asymmetric Magnetization Reversal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Direct Imaging of Asymmetric Magnetization Reversal Print The phenomenon of exchange bias has transformed how data is read on magnetic hard disks and created an explosion in their information storage density. However, it remains poorly understood, and even the fundamental mechanism of magnetic reversal for exchange-biased systems in changing magnetic fields is unclear. By using x-ray photoemission electron microscopy at the ALS to directly image the magnetic structure of an exchange-biased film,

  13. Direct Imaging of Asymmetric Magnetization Reversal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Direct Imaging of Asymmetric Magnetization Reversal Print The phenomenon of exchange bias has transformed how data is read on magnetic hard disks and created an explosion in their information storage density. However, it remains poorly understood, and even the fundamental mechanism of magnetic reversal for exchange-biased systems in changing magnetic fields is unclear. By using x-ray photoemission electron microscopy at the ALS to directly image the magnetic structure of an exchange-biased film,

  14. Actively controlling coolant-cooled cold plate configuration

    DOE Patents [OSTI]

    Chainer, Timothy J.; Parida, Pritish R.

    2015-07-28

    A method is provided to facilitate active control of thermal and fluid dynamic performance of a coolant-cooled cold plate. The method includes: monitoring a variable associated with at least one of the coolant-cooled cold plate or one or more electronic components being cooled by the cold plate; and dynamically varying, based on the monitored variable, a physical configuration of the cold plate. By dynamically varying the physical configuration, the thermal and fluid dynamic performance of the cold plate are adjusted to, for example, optimally cool the one or more electronic components, and at the same time, reduce cooling power consumption used in cooling the electronic component(s). The physical configuration can be adjusted by providing one or more adjustable plates within the coolant-cooled cold plate, the positioning of which may be adjusted based on the monitored variable.

  15. REVERSE RADIATIVE SHOCK LASER EXPERIMENTS RELEVANT TO ACCRETING...

    Office of Scientific and Technical Information (OSTI)

    REVERSE RADIATIVE SHOCK LASER EXPERIMENTS RELEVANT TO ACCRETING STREAM-DISK IMPACT IN INTERACTING BINARIES Citation Details In-Document Search Title: REVERSE RADIATIVE SHOCK LASER ...

  16. Time-reversal symmetric hierarchy of fractional incompressible...

    Office of Scientific and Technical Information (OSTI)

    Time-reversal symmetric hierarchy of fractional incompressible liquids Title: Time-reversal symmetric hierarchy of fractional incompressible liquids Authors: Santos, Luiz ; ...

  17. Reversible Metal Hydride Thermal Energy Storage for High Temperature...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Reversible Metal Hydride Thermal Energy Storage for High Temperature Power Generation Systems Reversible Metal Hydride Thermal Energy Storage for High Temperature Power Generation ...

  18. Fractional Topological Phases and Broken Time-Reversal Symmetry...

    Office of Scientific and Technical Information (OSTI)

    Fractional Topological Phases and Broken Time-Reversal Symmetry in Strained Graphene Title: Fractional Topological Phases and Broken Time-Reversal Symmetry in Strained Graphene ...

  19. Reversible ratchet effects for vortices in conformal pinning...

    Office of Scientific and Technical Information (OSTI)

    Reversible ratchet effects for vortices in conformal pinning arrays Citation Details In-Document Search This content will become publicly available on May 3, 2016 Title: Reversible...

  20. Time-reversal-invariant topological superconductivity in n -doped...

    Office of Scientific and Technical Information (OSTI)

    Time-reversal-invariant topological superconductivity in n -doped BiH Citation Details In-Document Search Title: Time-reversal-invariant topological superconductivity in n -doped ...

  1. C6 plate puncture testing report.

    SciTech Connect (OSTI)

    Vangoethem, Douglas J.; Cordova, Theresa Elena; Reu, Phillip L.

    2013-04-01

    There are numerous scenarios where critical systems could be subject to penetration by projectiles or fixed objects (e.g., collision, natural disaster, act of terrorism, etc.). It is desired to use computational models to examine these scenarios and make risk-informed decisions; however, modeling of material failure is an active area of research, and new models must be validated with experimental data. The purpose of this report is to document the experimental work performed from FY07 through FY08 on the Campaign Six Plate Puncture project. The goal of this project was to acquire experimental data on the puncture and penetration of metal plates for use in model validation. Of particular interest is the PLH failure model also known as the multilinear line segment model. A significant amount of data that will be useful for the verification and validation of computational models of ductile failure were collected during this project were collected and documented herein; however, much more work remains to be performed, collecting additional experimental data that will further the task of model verification.

  2. Time reversal signal processing for communication.

    SciTech Connect (OSTI)

    Young, Derek P.; Jacklin, Neil; Punnoose, Ratish J.; Counsil, David T.

    2011-09-01

    Time-reversal is a wave focusing technique that makes use of the reciprocity of wireless propagation channels. It works particularly well in a cluttered environment with associated multipath reflection. This technique uses the multipath in the environment to increase focusing ability. Time-reversal can also be used to null signals, either to reduce unintentional interference or to prevent eavesdropping. It does not require controlled geometric placement of the transmit antennas. Unlike existing techniques it can work without line-of-sight. We have explored the performance of time-reversal focusing in a variety of simulated environments. We have also developed new algorithms to simultaneously focus at a location while nulling at an eavesdropper location. We have experimentally verified these techniques in a realistic cluttered environment.

  3. Optimal design of reverse osmosis module networks

    SciTech Connect (OSTI)

    Maskan, F.; Wiley, D.E.; Johnston, L.P.M.; Clements, D.J.

    2000-05-01

    The structure of individual reverse osmosis modules, the configuration of the module network, and the operating conditions were optimized for seawater and brackish water desalination. The system model included simple mathematical equations to predict the performance of the reverse osmosis modules. The optimization problem was formulated as a constrained multivariable nonlinear optimization. The objective function was the annual profit for the system, consisting of the profit obtained from the permeate, capital cost for the process units, and operating costs associated with energy consumption and maintenance. Optimization of several dual-stage reverse osmosis systems were investigated and compared. It was found that optimal network designs are the ones that produce the most permeate. It may be possible to achieve economic improvements by refining current membrane module designs and their operating pressures.

  4. Transport Physics in Reversed Shear Plasmas

    SciTech Connect (OSTI)

    Levinton, F.M.; Batha, S.H.; Beer, M.A.; Bell, M.G.; Budny, R.V.; Efthimion, P.C.; Mazzucato, E.; Nazikian, R.; Park, H.K.; Ramsey, A.T.; Schmidt, G.L.; Scott, S.D.; Synakowski, E.J.; Taylor, G.; Von Goeler, S.; Zarnstorff, M.C.; Bush, C.E.

    1997-12-31

    Reversed magnetic shear is considered a good candidate for improving the tokamak concept because it has the potential to stabilize MHD instabilities and reduce particle and energy transport. With reduced transport the high pressure gradient would generate a strong off-axis bootstrap current and could sustain a hollow current density profile. Such a combination of favorable conditions could lead to an attractive steady-state tokamak configuration. Indeed, a new tokamak confinement regime with reversed magnetic shear has been observed on the Tokamak Fusion Test Reactor (TFTR) where the particle, momentum, and ion thermal diffusivities drop precipitously, by over an order of magnitude. The particle diffusivity drops to the neoclassical level and the ion thermal diffusivity drops to much less than the neoclassical value in the region with reversed shear. This enhanced reversed shear (ERS) confinement mode is characterized by an abrupt transition with a large rate of rise of the density in the reversed shear region during neutral beam injection, resulting in nearly a factor of three increase in the central density to 1.2 X 10(exp 20) cube m. At the same time the density fluctuation level in the reversed shear region dramatically decreases. The ion and electron temperatures, which are about 20 keV and 7 keV respectively, change little during the ERS mode. The transport and transition into and out of the ERS mode have been studied on TFTR with plasma currents in the range 0.9-2.2 MA, with a toroidal magnetic field of 2.7-4.6 T, and the radius of the q(r) minimum, q{sub min}, has been varied from r/a = 0.35 to 0.55. Toroidal field and co/counter neutral beam injection toroidal rotation variations have been used to elucidate the underlying physics of the transition mechanism and power threshold of the ERS mode.

  5. A unidirectional subwavelength focusing near-field plate

    SciTech Connect (OSTI)

    Imani, Mohammadreza F.; Grbic, Anthony

    2014-01-28

    Near-field plates consist of non-periodically patterned surfaces that can overcome the diffraction limit and confine electromagnetic fields to subwavelength dimensions. Previous near-field plates experimentally demonstrated extreme field tailoring capabilities. However, their performance suffered from radiation/reflection in undesired directions, those other than the subwavelength focus. This issue can limit the practical use of near-field plates. In this paper, we address this issue by designing a unidirectional near-field plate that can form a subwavelength focal pattern, while suppressing the field radiated/reflected in other directions. The design and operation of the proposed unidirectional near-field plate are verified through full-wave simulation. The unidirectional near-field plate may find application in high resolution imaging and probing, high density data storage, and wireless power transfer systems. As an example, its utility as a high resolution probe is demonstrated through full-wave electromagnetic simulation.

  6. Adapter plate assembly for adjustable mounting of objects

    DOE Patents [OSTI]

    Blackburn, Robert S.

    1987-01-01

    An adapter plate and two locking discs are together affixed to an optic table with machine screws or bolts threaded into a fixed array of internally threaded holes provided in the table surface. The adapter plate preferably has two, and preferably parallel, elongated locating slots each freely receiving a portion of one of the locking discs for secure affixation of the adapter plate to the optic table. A plurality of threaded apertures provided in the adapter plate are available to attach optical mounts or other devices onto the adapter plate in an orientation not limited by the disposition of the array of threaded holes in the table surface. An axially aligned but radially offset hole through each locking disc receives a screw that tightens onto the table, such that prior to tightening of the screw the locking disc may rotate and translate within each locating slot of the adapter plate for maximum flexibility of the orientation thereof.

  7. Adapter plate assembly for adjustable mounting of objects

    DOE Patents [OSTI]

    Blackburn, R.S.

    1986-05-02

    An adapter plate and two locking discs are together affixed to an optic table with machine screws or bolts threaded into a fixed array of internally threaded holes provided in the table surface. The adapter plate preferably has two, and preferably parallel, elongated locating slots each freely receiving a portion of one of the locking discs for secure affixation of the adapter plate to the optic table. A plurality of threaded apertures provided in the adapter plate are available to attach optical mounts or other devices onto the adapter plate in an orientation not limited by the disposition of the array of threaded holes in the table surface. An axially aligned but radially offset hole through each locking disc receives a screw that tightens onto the table, such that prior to tightening of the screw the locking disc may rotate and translate within each locating slot of the adapter plate for maximum flexibility of the orientation thereof.

  8. Catalytic bipolar interconnection plate for use in a fuel cell

    DOE Patents [OSTI]

    Lessing, Paul A.

    1996-01-01

    A bipolar interconnection plate for use between adjacent fuel cell units in a stacked fuel cell assembly. Each plate is manufactured from an intermetallic composition, examples of which include NiAl or Ni.sub.3 Al which can catalyze steam reforming of hydrocarbons. Distributed within the intermetallic structure of the plate is a ceramic filler composition. The plate includes a first side with gas flow channels therein and a second side with fuel flow channels therein. A protective coating is applied to the first side, with exemplary coatings including strontium-doped or calcium-doped lanthanum chromite. To produce the plate, Ni and Al powders are combined with the filler composition, compressed at a pressure of about 10,000-30,000 psi, and heated to about 600.degree.-1000.degree. C. The coating is then applied to the first side of the completed plate using liquid injection plasma deposition or other deposition techniques.

  9. Catalytic bipolar interconnection plate for use in a fuel cell

    DOE Patents [OSTI]

    Lessing, P.A.

    1996-03-05

    A bipolar interconnection plate is described for use between adjacent fuel cell units in a stacked fuel cell assembly. Each plate is manufactured from an intermetallic composition, examples of which include NiAl or Ni{sub 3}Al which can catalyze steam reforming of hydrocarbons. Distributed within the intermetallic structure of the plate is a ceramic filler composition. The plate includes a first side with gas flow channels therein and a second side with fuel flow channels therein. A protective coating is applied to the first side, with exemplary coatings including strontium-doped or calcium-doped lanthanum chromite. To produce the plate, Ni and Al powders are combined with the filler composition, compressed at a pressure of about 10,000--30,000 psi, and heated to about 600--1000 C. The coating is then applied to the first side of the completed plate using liquid injection plasma deposition or other deposition techniques. 6 figs.

  10. Experimental Study on Flow Optimization in Upper Plenum of Reactor Vessel for a Compact Sodium-Cooled Fast Reactor

    SciTech Connect (OSTI)

    Kimura, Nobuyuki; Hayashi, Kenji; Kamide, Hideki; Itoh, Masami; Sekine, Tadashi

    2005-11-15

    An innovative sodium-cooled fast reactor has been investigated in a feasibility study of fast breeder reactor cycle systems in Japan. A compact reactor vessel and a column-type upper inner structure with a radial slit for an arm of a fuel-handling machine (FHM) are adopted. Dipped plates are set in the reactor vessel below the free surface to prevent gas entrainment. We performed a one-tenth-scaled model water experiment for the upper plenum of the reactor vessel. Gas entrainment was not observed in the experiment under the same velocity condition as the reactor. Three vortex cavitations were observed near the hot-leg inlet. A vertical rib on the reactor vessel wall was set to restrict the rotating flow near the hot leg. The vortex cavitation between the reactor vessel wall and the hot leg was suppressed by the rib under the same cavitation factor condition as in the reactor. The cylindrical plug was installed through the hole in the dipped plates for the FHM to reduce the flow toward the free surface. It was effective when the plug was submerged into the middle height in the upper plenum. This combination of two components had a possibility to optimize the flow in the compact reactor vessel.

  11. Ponderomotive phase plate for transmission electron microscopes (Patent) |

    Office of Scientific and Technical Information (OSTI)

    DOEPatents Ponderomotive phase plate for transmission electron microscopes Title: Ponderomotive phase plate for transmission electron microscopes A ponderomotive phase plate system and method for controllably producing highly tunable phase contrast transfer functions in a transmission electron microscope (TEM) for high resolution and biological phase contrast imaging. The system and method includes a laser source and a beam transport system to produce a focused laser crossover as a phase

  12. Growth plate closure: Apex view on bone scan

    SciTech Connect (OSTI)

    Giles, P.H.; Trochei, M.; Yeates, K.

    1984-01-01

    Angular deformities of the extremities in children following premature closure of the growth plate are well known. The deformities depend on the position of an osseus bridge which forms between the epiphysis and metaphysis. Several surgical procedures including resection of the osseus bridge have been described, however, delineation of the site of fusion is difficult to define. The commonest site of growth plate arrest is the distal femoral or proximal tibial growth plate. A new technique using the bone scan has been developed which accurately defines the area and position of these osseus bridges. Two hours after injection of technetium 99m methylene diphosphonate apex views of the affected distal femoral growth plate were performed. The knee was flexed into its smallest angle. Using a pinhole collimator the gamma camera was angled to face the affected growth plate end on. The image was collected onto computer and analysed by: (I) regions of interest over segments of the growth plate to calculate the relative area of total growth plate affected: (II) generating histograms: (III) thresholding or performing isocontours to accentuate abnormal areas. The growth plate is normally uniformly increased when compared to the normal shaft of the bone. Fusion across the plate appears as an area of diminished uptake. The apex view gives a unique functional map of the growth plate such that abnormal areas are displayed, and the site, size and position of osseus fusion obtained. The technique has the potential for determining the metabolic activity of the growth plate before and after surgery. Serial studies will allow assessment of regneration of the plate and reformation of new osseus bridges.

  13. Thermal Hydraulic Characteristics of Fuel Defects in Plate Type Nuclear

    Office of Scientific and Technical Information (OSTI)

    Research Reactors (Technical Report) | SciTech Connect Technical Report: Thermal Hydraulic Characteristics of Fuel Defects in Plate Type Nuclear Research Reactors Citation Details In-Document Search Title: Thermal Hydraulic Characteristics of Fuel Defects in Plate Type Nuclear Research Reactors Turbulent flow coupled with heat transfer is investigated for a High Flux Isotope Reactor (HFIR) fuel plate. The Reynolds Averaged Navier-Stokes Models are used for fluid dynamics and the transfer of

  14. Flat-Plate Photovoltaic System Basics | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    System Basics Flat-Plate Photovoltaic System Basics August 20, 2013 - 4:03pm Addthis The most common photovoltaic (PV) array design uses flat-plate PV modules or panels. These panels can be fixed in place or allowed to track the movement of the Illustration of a cutaway of a typical flat-plate module. The layers, in order from top to bottom, are: cover film, solar cell, encapsulant, substrate, cover film, seal, gasket, and frame. One typical flat-plate module design uses a substrate of metal,

  15. Corrosion Test Cell for Biopolar Plate Materials - Energy Innovation...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Return to Search Corrosion Test Cell for Biopolar Plate Materials Los Alamos National Laboratory Contact LANL About This Technology Technology Marketing SummaryA corrosion test ...

  16. Thermal Hydraulic Characteristics of Fuel Defects in Plate Type...

    Office of Scientific and Technical Information (OSTI)

    Technical Report: Thermal Hydraulic Characteristics of Fuel Defects in Plate Type Nuclear Research Reactors Citation Details In-Document Search Title: Thermal Hydraulic ...

  17. Thermal Hydraulic Characteristics of Fuel Defects in Plate Type...

    Office of Scientific and Technical Information (OSTI)

    Title: Thermal Hydraulic Characteristics of Fuel Defects in Plate Type Nuclear Research Reactors Turbulent flow coupled with heat transfer is investigated for a High Flux Isotope ...

  18. Upper Rio Grande Simulation Model (URGSIM)

    Energy Science and Technology Software Center (OSTI)

    2010-08-05

    URGSIM estimates the location of surface water and groundwater resources in the upper Rio Grande Basin between the Colorado-New Mexico state line, and Caballo Reservoir from 1975 - 2045. It is a mass balance hydrology model of the Upper Rio Grande surface water, groundwater, and water demand systems which runs at a monthly timestep from 1975-1999 in calibration mode, 2000 – 2004 in validation mode, and 2005 – 2045 in scenario analysis mode.

  19. Upper Skagit Indian Tribe - Strategic Energy Planning

    Energy Savers [EERE]

    Upper Skagit Indian Tribe Tribal Lands Location Tribal lands Tribal lands Two Tribe Land sites: Two Tribe Land sites: Bow Hill Complex Bow Hill Complex The Tribal economic center with both development The Tribal economic center with both development & undeveloped lands. & undeveloped lands. Helmick Road Reservation Helmick Road Reservation The community & government center with both The community & government center with both developed & newly required community lands.

  20. Vacuum fusion bonded glass plates having microstructures thereon

    DOE Patents [OSTI]

    Swierkowski, Steve P.; Davidson, James C.; Balch, Joseph W.

    2001-01-01

    An improved apparatus and method for vacuum fusion bonding of large, patterned glass plates. One or both glass plates are patterned with etched features such as microstructure capillaries and a vacuum pumpout moat, with one plate having at least one hole therethrough for communication with a vacuum pumpout fixture. High accuracy alignment of the plates is accomplished by a temporary clamping fixture until the start of the fusion bonding heat cycle. A complete, void-free fusion bond of seamless, full-strength quality is obtained through the plates; because the glass is heated well into its softening point and because of a large, distributed force that is developed that presses the two plates together from the difference in pressure between the furnace ambient (high pressure) and the channeling and microstructures in the plates (low pressure) due to the vacuum drawn. The apparatus and method may be used to fabricate microcapillary arrays for chemical electrophoresis; for example, any apparatus using a network of microfluidic channels embedded between plates of glass or similar moderate melting point substrates with a gradual softening point curve, or for assembly of glass-based substrates onto larger substrates, such as in flat panel display systems.

  1. Process for protecting bonded components from plating shorts

    DOE Patents [OSTI]

    Tarte, Lisa A.; Bonde, Wayne L.; Carey, Paul G.; Contolini, Robert J.; McCarthy, Anthony M.

    2000-01-01

    A method which protects the region between a component and the substrate onto which the components is bonded using an electrically insulating fillet of photoresist. The fillet protects the regions from subsequent plating with metal and therefore shorting the plated conductors which run down the sides of the component and onto the substrate.

  2. Partial growth plate closure: apex view on bone scan

    SciTech Connect (OSTI)

    Howman-Giles, R.; Trochei, M.; Yeates, K.; Middleton, R.; Barrett, I.; Scougall, J.; Whiteway, D.

    1985-01-01

    A new technique of using /sup 99m/Tc bone scan to assess partial closure of the growth plate is described. The site and degree of osseous fusion can be obtained by using the apex view. The technique has the potential of assessing serially the growth of a plate before and after surgery.

  3. Upper Bound on the First Star Formation History (Journal Article...

    Office of Scientific and Technical Information (OSTI)

    Upper Bound on the First Star Formation History Citation Details In-Document Search Title: Upper Bound on the First Star Formation History You are accessing a document from the ...

  4. Sandia Energy - Upper Rio Grande Simulation Model (URGSiM)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Upper Rio Grande Simulation Model (URGSiM) Home Climate & Earth Systems WaterEnergy Nexus Decision Models for Integrating EnergyWater Systems Modeling Upper Rio Grande Simulation...

  5. Upper Cumberland E M C | Open Energy Information

    Open Energy Info (EERE)

    Upper Cumberland E M C Jump to: navigation, search Name: Upper Cumberland E M C Place: Tennessee Phone Number: 931-528-5449 or 931-372-2323 or 931-268-2123 or 931-268-5866 or...

  6. Evidence for long-lived subduction of an ancient tectonic plate beneath the southern Indian Ocean

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Simmons, N. A.; Myers, S. C.; Johannesson, G.; Matzel, E.; Grand, S. P.

    2015-11-14

    In this study, ancient subducted tectonic plates have been observed in past seismic images of the mantle beneath North America and Eurasia, and it is likely that other ancient slab structures have remained largely hidden, particularly in the seismic-data-limited regions beneath the vast oceans in the Southern Hemisphere. Here we present a new global tomographic image, which shows a slab-like structure beneath the southern Indian Ocean with coherency from the upper mantle to the core-mantle boundary region—a feature that has never been identified. We postulate that the structure is an ancient tectonic plate that sank into the mantle along anmore » extensive intraoceanic subduction zone that migrated southwestward across the ancient Tethys Ocean in the Mesozoic Era. Slab material still trapped in the transition zone is positioned near the edge of East Gondwana at 140 Ma suggesting that subduction terminated near the margin of the ancient continent prior to breakup and subsequent dispersal of its subcontinents.« less

  7. Sub-Seafloor Carbon Dioxide Storage Potential on the Juan de Fuca Plate, Western North America

    SciTech Connect (OSTI)

    Jerry Fairley; Robert Podgorney

    2012-11-01

    The Juan de Fuca plate, off the western coast of North America, has been suggested as a site for geological sequestration of waste carbon dioxide because of its many attractive characteristics (high permeability, large storage capacity, reactive rock types). Here we model CO2 injection into fractured basalts comprising the upper several hundred meters of the sub-seafloor basalt reservoir, overlain with low-permeability sediments and a large saline water column, to examine the feasibility of this reservoir for CO2 storage. Our simulations indicate that the sub-seafloor basalts of the Juan de Fuca plate may be an excellent CO2 storage candidate, as multiple trapping mechanisms (hydrodynamic, density inversions, and mineralization) act to keep the CO2 isolated from terrestrial environments. Questions remain about the lateral extent and connectivity of the high permeability basalts; however, the lack of wells or boreholes and thick sediment cover maximize storage potential while minimizing potential leakage pathways. Although promising, more study is needed to determine the economic viability of this option.

  8. Evidence for long-lived subduction of an ancient tectonic plate beneath the southern Indian Ocean

    SciTech Connect (OSTI)

    Simmons, N. A.; Myers, S. C.; Johannesson, G.; Matzel, E.; Grand, S. P.

    2015-11-14

    In this study, ancient subducted tectonic plates have been observed in past seismic images of the mantle beneath North America and Eurasia, and it is likely that other ancient slab structures have remained largely hidden, particularly in the seismic-data-limited regions beneath the vast oceans in the Southern Hemisphere. Here we present a new global tomographic image, which shows a slab-like structure beneath the southern Indian Ocean with coherency from the upper mantle to the core-mantle boundary region—a feature that has never been identified. We postulate that the structure is an ancient tectonic plate that sank into the mantle along an extensive intraoceanic subduction zone that migrated southwestward across the ancient Tethys Ocean in the Mesozoic Era. Slab material still trapped in the transition zone is positioned near the edge of East Gondwana at 140 Ma suggesting that subduction terminated near the margin of the ancient continent prior to breakup and subsequent dispersal of its subcontinents.

  9. Status of high-density fuel plates fabrication

    SciTech Connect (OSTI)

    Wiencek, T.C.; Domagala, R.F.; Thresh, H.R.

    1989-09-01

    Progress has continued on the fabrication of fuel plates with fuel zone loadings approaching 9gU/cm{sup 3}. Using Hot Isostatic Pressing (HIPping) successful diffusion bonds have been made with 110 Al and 6061 Al alloys. These bonds demonstrated the most critical processing step for proof-of-concept hardware. Two types of prototype highly-loaded fuel plates have been fabricated. First, a fuel plate in which 0.030 in. (0.76 mm) uranium compound wires are bonded within an aluminum cladding and second, a dispersion fuel plate with uniform cladding and fuel zone thickness. The successful fabrication of these fuel plates derives from the unique ability of the HIPping process to produce diffusion bonds with minimal deformation. 2 refs., 3 figs.

  10. Upper East Fork Poplar Creek | Department of Energy

    Energy Savers [EERE]

    Upper East Fork Poplar Creek Upper East Fork Poplar Creek This document discusses the Upper East Fork Poplar Creek. Topics include: * The area's safety * Any use limitations for the area * History and cleanup background for this area * How DOE's cleanup program addressed the problem PDF icon Upper East Fork Poplar Creek Watershed fact sheet More Documents & Publications Lower East Fork Poplar Creek Recommendation 229: Recommendation on the Preferred Alternative for the Proposed Plan for

  11. Forward and reverse characteristics of irradiated MOSFETs

    SciTech Connect (OSTI)

    Paccagnella, A.; Ceschia, M.; Verzellesi, G.; Dalla Betta, G.F.; Soncini, G.; Bellutti, P.; Fuochi, P.G.

    1996-06-01

    pMOSFETs biased with V{sub gs} < V{sub gd} during Co{sup 60} {gamma} irradiation have shown substantial differences between the forward and reverse subthreshold characteristics, induced by a non-uniform charge distribution in the gate oxide. Correspondingly, modest differences have been observed in the over-threshold I-V characteristics. After irradiation, the forward subthreshold curves can shift at higher or lower gate voltages than the reverse ones. The former behavior has been observed in long-channel devices, in agreement with the classical MOS theory and numerical simulations. The latter result has been obtained in short-channel devices, and it has been correlated to a parasitic punch-through conduction mechanism.

  12. On the design of reversible QDCA systems.

    SciTech Connect (OSTI)

    DeBenedictis, Erik P.; Frank, Michael P. (Florida State University, Tallahassee, FL); Ottavi, Marco; Frost-Murphy, Sarah E.

    2006-10-01

    This work is the first to describe how to go about designing a reversible QDCA system. The design space is substantial, and there are many questions that a designer needs to answer before beginning to design. This document begins to explicate the tradeoffs and assumptions that need to be made and offers a range of approaches as starting points and examples. This design guide is an effective tool for aiding designers in creating the best quality QDCA implementation for a system.

  13. Upper Skagit Indian Tribe- 2005 Project

    Broader source: Energy.gov [DOE]

    The Upper Skagit Indian Tribe lands consist of 550 acres of the Bow Hill Complex with reservation and new development economic lands located in Skagit County, Washington, adjacent to Interstate 5. The strategic energy plan would complete an assessment of the existing economic enterprises including hotel, convention center, and casino, plus potential green energy sources to serve the existing and developing facilities. The strategic energy analysis would complete an assessment of 50 acres acquired in October 2004, to build more low-income houses, and identify energy improvements for the existing fully developed 74 acres of the Helmick Road Reservation established in 1981.

  14. Waste treatment by reverse osmosis and membrane processes: Industrial. (Latest citations from the EI compendex*plus database). Published Search

    SciTech Connect (OSTI)

    1995-09-01

    The bibliography contains citations concerning the use of membranes in the treatment of industrial wastewaters. Reverse osmosis, ion exchange, electrodialysis, liquid membranes, and ultrafiltration techniques are described. Wastewater treatments for removal of metals, ammonia, sodium compounds, nitrates, fluorides, dyes, biologicals, and radioactive waste using membrane technology are discussed. Applications of this technology to the chemical, petrochemical, pulp, textile, steel, ore treatment, electro-plating, and other wastewater and groundwater-remediation industries are included.(Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

  15. Waste treatment by reverse osmosis and membrane processes: Industrial. (Latest citations from the Compendex database). Published Search

    SciTech Connect (OSTI)

    Not Available

    1993-05-01

    The bibliography contains citations concerning the use of membranes in the treatment of industrial wastewaters. Reverse osmosis, ion exchange, electrodialysis, liquid membranes, and ultrafiltration techniques are described. Wastewater treatments for removal of metals, ammonia, sodium compounds, nitrates, fluorides, dyes, biologicals, and radioactive waste using membrane technology are discussed. Applications of this technology to the chemical, petrochemical, pulp, textile, steel, ore treatment, electro-plating, and other wastewater and groundwater-remediation industries are included. (Contains 250 citations and includes a subject term index and title list.)

  16. Waste treatment by reverse osmosis and membrane processes: Industrial. (Latest citations from the EI Compendex*Plus database). Published Search

    SciTech Connect (OSTI)

    Not Available

    1993-12-01

    The bibliography contains citations concerning the use of membranes in the treatment of industrial wastewaters. Reverse osmosis, ion exchange, electrodialysis, liquid membranes, and ultrafiltration techniques are described. Wastewater treatments for removal of metals, ammonia, sodium compounds, nitrates, fluorides, dyes, biologicals, and radioactive waste using membrane technology are discussed. Applications of this technology to the chemical, petrochemical, pulp, textile, steel, ore treatment, electro-plating, and other wastewater and groundwater-remediation industries are included. (Contains 250 citations and includes a subject term index and title list.)

  17. Reversible Sigma C-C Bond Formation Between Phenanthroline Ligands...

    Office of Scientific and Technical Information (OSTI)

    Reversible Sigma C-C Bond Formation Between Phenanthroline Ligands Activated by (C5Me5)2Yb Citation Details In-Document Search Title: Reversible Sigma C-C Bond Formation Between ...

  18. Perforated plates for cryogenic regenerators and method of fabrication

    DOE Patents [OSTI]

    Hendricks, John B. (Huntsville, AL)

    1994-01-01

    Perforated plates (10) having very small holes (14) with a uniform diameter throughout the plate thickness are prepared by a "wire drawing" process in which a billet of sacrificial metal is disposed in an extrusion can of the plate metal, and the can is extruded and restacked repeatedly, converting the billet to a wire of the desired hole diameter. At final size, the rod is then sliced into wafers, and the wires are removed by selective etching. This process is useful for plate metals of interest for high performance regenerator applications, in particular, copper, niobium, molybdenum, erbium, and other rare earth metals. Er.sub.3 Ni, which has uniquely favorable thermophysical properties for such applications, may be incorporated in regions of the plates by providing extrusion cans (20) containing erbium and nickel metals in a stacked array (53) with extrusion cans of the plate metal, which may be copper. The array is heated to convert the erbium and nickel metals to Er.sub.3 Ni. Perforated plates having two sizes of perforations (38, 42), one of which is small enough for storage of helium, are also disclosed.

  19. Perforated plates for cryogenic regenerators and method of fabrication

    DOE Patents [OSTI]

    Hendricks, J.B.

    1994-03-29

    Perforated plates having very small holes with a uniform diameter throughout the plate thickness are prepared by a [open quotes]wire drawing[close quotes] process in which a billet of sacrificial metal is disposed in an extrusion can of the plate metal, and the can is extruded and restacked repeatedly, converting the billet to a wire of the desired hole diameter. At final size, the rod is then sliced into wafers, and the wires are removed by selective etching. This process is useful for plate metals of interest for high performance regenerator applications, in particular, copper, niobium, molybdenum, erbium, and other rare earth metals. Er[sub 3]Ni, which has uniquely favorable thermophysical properties for such applications, may be incorporated in regions of the plates by providing extrusion cans containing erbium and nickel metals in a stacked array with extrusion cans of the plate metal, which may be copper. The array is heated to convert the erbium and nickel metals to Er[sub 3]Ni. Perforated plates having two sizes of perforations, one of which is small enough for storage of helium, are also disclosed. 10 figures.

  20. Progress on the Development of Reversible SOFC Stack Technology

    Broader source: Energy.gov [DOE]

    Presentation by Casey Brown, Versa Power Systems, at the NREL Reversible Fuel Cells Workshop, April 19, 2011

  1. Development of Reversible Fuel Cell Systems at Proton Energy | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Reversible Fuel Cell Systems at Proton Energy Development of Reversible Fuel Cell Systems at Proton Energy Presentation by Everett Anderson, PROTON ON SITE, at the NREL Reversible Fuel Cells Workshop, April 19, 2011 PDF icon rev_fc_wkshp_anderson.pdf More Documents & Publications Reversible Fuel Cells Workshop Summary Report Regenerative Fuel Cells for Energy Storage Small Business Innovation Research (SBIR) Award Success Story: Proton Energy Systems

  2. Water-supply potential of the Upper Floridan aquifer in the vicinity of Savannah, Georgia

    SciTech Connect (OSTI)

    Garza, R.; Krause, R.E. )

    1993-03-01

    The Upper Floridan aquifer is the primary source of freshwater in coastal Georgia. Groundwater withdrawal in the area of Savannah and in the adjacent coastal areas in Georgia and South Carolina has resulted in large regional water-level declines and a reversal of the hydraulic gradient that existed prior to development. Changes in gradient and decreasing water levels are causing lateral encroachment of seawater into the Upper Floridan aquifer at the northern end of Hilton Head Island, SC, and vertical intrusion of saltwater into the Upper and Lower Floridan aquifers in the Brunswick, GA., area. Concerns about future water-supply demands prompted the US Geological Survey and the Chatham County-Savannah Metropolitan Planning Commission to undertake a cooperative study to evaluate the ground-water resources in the Savannah, GA, area. A numerical ground-water flow model was developed and used in conjunction with other previously calibrated models in the coastal areas of Georgia and South Carolina to simulate the effects of additional ground-water withdrawal on water levels. Based on model simulations and the constraint of preventing additional water-level declines at the locations of encroachment and intrusion, the potential of the Upper Floridan aquifer to supply additional water in the Savannah area is limited under present hydrologic conditions. The potential for additional withdrawal in the vicinity of Savannah, GA, ranges from less than 1 million gallons per day (Mgal/d) to about 5 Mgal/d. Because of the limited water-supply potential, hypothetical alternatives of ground-water withdrawal were simulated to determine the effects on water levels. These simulations indicate that reduction and redistribution of ground-water withdrawal would not adversely affect water levels at the locations of encroachment and intrusion.

  3. Time Reversal in Solids (Linear and Nonlinear Elasticity): Multimedia Resources in Time Reversal

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Dynamic nonlinear elastic behavior, nonequilibrium dynamics, first observed as a curiosity in earth materials has now been observed in a great variety of solids. The primary manifestations of the behavior are characteristic wave distortion, and slow dynamics, a recovery process to equilibrium that takes place linearly with the logarithm of time, over hours to days after a wave disturbance. The link between the diverse materials that exhibit nonequilibrium dynamics appears to be the presence of soft regions, thought to be 'damage' at many scales, ranging from order 10-9 m to 10-1 m at least. The regions of soft matter may be distributed as in a rock sample, or isolated, as in a sample with a single crack [LANLhttp://www.lanl.gov/orgs/ees/ees11/geophysics/nonlinear/nonlinear.shtml]. The Geophysics Group (EES-11) at Los Alamos National Laboratory has posted two or more multimedia items under each of the titles below to demonstrate aspects of their work: 1) Source Reconstruction Using Time Reversal; 2) Robustness and Efficiency of Time Reversal Acoustics in Solid Media; 3) Audio Example of Time Reversal - Speech Privacy; 4) Crack Imagining with Time Reversal - Experimental Results; 5) Time Reversal of the 2004 (M9.0) Sumatra Earthquake.

  4. Flat-Plate Photovoltaic Module Basics | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Module Basics Flat-Plate Photovoltaic Module Basics August 20, 2013 - 4:25pm Addthis Flat-plate photovoltaic (PV) modules are made of several components, including the front surface materials, encapsulant, rear surface, and frame. Front Surface Materials The front surface of a flat-plate PV module must have a high transmission in the wavelengths that can be used by the solar cells in the module. For example, for silicon solar cells, the top surface must have high transmission of light with

  5. Conductivity fuel cell collector plate and method of fabrication

    DOE Patents [OSTI]

    Braun, James C.

    2002-01-01

    An improved method of manufacturing a PEM fuel cell collector plate is disclosed. During molding a highly conductive polymer composite is formed having a relatively high polymer concentration along its external surfaces. After molding the polymer rich layer is removed from the land areas by machining, grinding or similar process. This layer removal results in increased overall conductivity of the molded collector plate. The polymer rich surface remains in the collector plate channels, providing increased mechanical strength and other benefits to the channels. The improved method also permits greater mold cavity thickness providing a number of advantages during the molding process.

  6. Double patterning HSQ processes of zone plates for 10 nm diffraction...

    Office of Scientific and Technical Information (OSTI)

    ... Using the new process, we successfully realized zone plates of 10 nm and 12 nm outermost zones. Fig. 3 shows the SEM micrographs of the zone plates outer regions. The zone plates ...

  7. Understanding the Initial Stages of Reversible Mg Deposition and Stripping in Inorganic Non-Aqueous Electrolytes

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Canepa, Pieremanuele; Gautam, Gopalakrishnan Sai; Malik, Rahul; Jayaraman, Saivenkataraman; Rong, Ziqin; Zavadil, Kevin R.; Persson, Kristin; Ceder, Gerbrand

    2015-04-08

    Multivalent (MV) battery architectures based on pairing a Mg metal anode with a high-voltage (~3 V) intercalation cathode offer a realistic design pathway toward significantly surpassing the energy storage performance of traditional Li-ion-based batteries, but there are currently only few electrolyte systems that support reversible Mg deposition. Using both static first-principles calculations and ab initio molecular dynamics, we perform a comprehensive adsorption study of several salt and solvent species at the interface of Mg metal with an electrolyte of Mg2+ and Cl–dissolved in liquid tetrahydrofuran (THF). Our findings not only provide a picture of the stable species at the interfacemore » but also explain how this system can support reversible Mg deposition, and as such, we provide insights in how to design other electrolytes for Mg plating and stripping. Furthermore, the active depositing species are identified to be (MgCl)+ monomers coordinated by THF, which exhibit preferential adsorption on Mg compared to possible passivating species (such as THF solvent or neutral MgCl2 complexes). We found that upon deposition, the energy to desolvate these adsorbed complexes and facilitate charge transfer is shown to be small (~61–46.2 kJ mol–1 to remove three THF from the strongest adsorbing complex), and the stable orientations of the adsorbed but desolvated (MgCl)+ complexes appear to be favorable for charge transfer. Finally, observations of Mg–Cl dissociation at the Mg surface at very low THF coordinations (0 and 1) suggest that deleterious Cl incorporation in the anode may occur upon plating. In the stripping process, this is beneficial by further facilitating the Mg removal reaction.« less

  8. Understanding the initial stages of reversible Mg deposition and stripping in inorganic nonaqueous electrolytes

    SciTech Connect (OSTI)

    Canepa, Pieremanuele; Gautam, Gopalakrishnan Sai; Malik, Rahul; Jayaraman, Saivenkataraman; Rong, Ziqin; Zavadil, Kevin R.; Persson, Kristin; Ceder, Gerbrand

    2015-04-08

    Multivalent (MV) battery architectures based on pairing a Mg metal anode with a high-voltage (~3 V) intercalation cathode offer a realistic design pathway toward significantly surpassing the energy storage performance of traditional Li-ion-based batteries, but there are currently only few electrolyte systems that support reversible Mg deposition. Using both static first-principles calculations and ab initio molecular dynamics, we perform a comprehensive adsorption study of several salt and solvent species at the interface of Mg metal with an electrolyte of Mg2+ and Cl–dissolved in liquid tetrahydrofuran (THF). Our findings not only provide a picture of the stable species at the interface but also explain how this system can support reversible Mg deposition, and as such, we provide insights in how to design other electrolytes for Mg plating and stripping. Furthermore, the active depositing species are identified to be (MgCl)+ monomers coordinated by THF, which exhibit preferential adsorption on Mg compared to possible passivating species (such as THF solvent or neutral MgCl2 complexes). We found that upon deposition, the energy to desolvate these adsorbed complexes and facilitate charge transfer is shown to be small (~61–46.2 kJ mol–1 to remove three THF from the strongest adsorbing complex), and the stable orientations of the adsorbed but desolvated (MgCl)+ complexes appear to be favorable for charge transfer. Lastly, observations of Mg–Cl dissociation at the Mg surface at very low THF coordinations (0 and 1) suggest that deleterious Cl incorporation in the anode may occur upon plating. In the stripping process, this is beneficial by further facilitating the Mg removal reaction.

  9. Understanding the initial stages of reversible Mg deposition and stripping in inorganic nonaqueous electrolytes

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Canepa, Pieremanuele; Gautam, Gopalakrishnan Sai; Malik, Rahul; Jayaraman, Saivenkataraman; Rong, Ziqin; Zavadil, Kevin R.; Persson, Kristin; Ceder, Gerbrand

    2015-04-08

    Multivalent (MV) battery architectures based on pairing a Mg metal anode with a high-voltage (~3 V) intercalation cathode offer a realistic design pathway toward significantly surpassing the energy storage performance of traditional Li-ion-based batteries, but there are currently only few electrolyte systems that support reversible Mg deposition. Using both static first-principles calculations and ab initio molecular dynamics, we perform a comprehensive adsorption study of several salt and solvent species at the interface of Mg metal with an electrolyte of Mg2+ and Cl–dissolved in liquid tetrahydrofuran (THF). Our findings not only provide a picture of the stable species at the interfacemore » but also explain how this system can support reversible Mg deposition, and as such, we provide insights in how to design other electrolytes for Mg plating and stripping. Furthermore, the active depositing species are identified to be (MgCl)+ monomers coordinated by THF, which exhibit preferential adsorption on Mg compared to possible passivating species (such as THF solvent or neutral MgCl2 complexes). We found that upon deposition, the energy to desolvate these adsorbed complexes and facilitate charge transfer is shown to be small (~61–46.2 kJ mol–1 to remove three THF from the strongest adsorbing complex), and the stable orientations of the adsorbed but desolvated (MgCl)+ complexes appear to be favorable for charge transfer. Lastly, observations of Mg–Cl dissociation at the Mg surface at very low THF coordinations (0 and 1) suggest that deleterious Cl incorporation in the anode may occur upon plating. In the stripping process, this is beneficial by further facilitating the Mg removal reaction.« less

  10. Understanding the Initial Stages of Reversible Mg Deposition and Stripping in Inorganic Non-Aqueous Electrolytes

    SciTech Connect (OSTI)

    Canepa, Pieremanuele; Gautam, Gopalakrishnan Sai; Malik, Rahul; Jayaraman, Saivenkataraman; Rong, Ziqin; Zavadil, Kevin R.; Persson, Kristin; Ceder, Gerbrand

    2015-04-08

    Multivalent (MV) battery architectures based on pairing a Mg metal anode with a high-voltage (~3 V) intercalation cathode offer a realistic design pathway toward significantly surpassing the energy storage performance of traditional Li-ion-based batteries, but there are currently only few electrolyte systems that support reversible Mg deposition. Using both static first-principles calculations and ab initio molecular dynamics, we perform a comprehensive adsorption study of several salt and solvent species at the interface of Mg metal with an electrolyte of Mg2+ and Cldissolved in liquid tetrahydrofuran (THF). Our findings not only provide a picture of the stable species at the interface but also explain how this system can support reversible Mg deposition, and as such, we provide insights in how to design other electrolytes for Mg plating and stripping. Furthermore, the active depositing species are identified to be (MgCl)+ monomers coordinated by THF, which exhibit preferential adsorption on Mg compared to possible passivating species (such as THF solvent or neutral MgCl2 complexes). We found that upon deposition, the energy to desolvate these adsorbed complexes and facilitate charge transfer is shown to be small (~6146.2 kJ mol1 to remove three THF from the strongest adsorbing complex), and the stable orientations of the adsorbed but desolvated (MgCl)+ complexes appear to be favorable for charge transfer. Finally, observations of MgCl dissociation at the Mg surface at very low THF coordinations (0 and 1) suggest that deleterious Cl incorporation in the anode may occur upon plating. In the stripping process, this is beneficial by further facilitating the Mg removal reaction.

  11. MODIFIED REVERSE OSMOSIS SYSTEM FOR TREATMENT OF PRODUCED WATERS

    SciTech Connect (OSTI)

    T.M. Whitworth; Liangxiong Li

    2002-09-15

    This report describes work performed during the second year of the project ''Modified reverse osmosis system for treatment of produced waters.'' We performed two series of reverse osmosis experiments using very thin bentonite clay membranes compacted to differing degrees. The first series of 10 experiments used NaCl solutions with membranes that ranged between 0.041 and 0.064mm in thickness. Our results showed compaction of such ultra-thin clay membranes to be problematic. The thickness of the membranes was exceeded by the dimensional variation in the machined experimental cell and this is believed to have resulted in local bypassing of the membrane with a resultant decrease in solute rejection efficiency. In two of the experiments, permeate flow was varied as a percentage of the total flow to investigate results of changing permeate flow on solute rejection. In one experiment, the permeate flow was varied between 2.4 and 10.3% of the total flow with no change in solute rejection. In another experiment, the permeate flow was varied between 24.6 and 52.5% of the total flow. In this experiment, the solute rejection rate decreased as the permeate occupied greater fractions of the total flow. This suggests a maximum solute rejection efficiency for these clay membranes for a permeate flow of between 10.3 and 24.6% of the total; flow. Solute rejection was found to decrease with increasing salt concentration and ranged between 62.9% and 19.7% for chloride and between 61.5 and 16.8% for sodium. Due to problems with the compaction procedure and potential membrane bypassing, these rejection rates are probably not the upper limit for NaCl rejection by bentonite membranes. The second series of four reverse osmosis experiments was conducted with a 0.057mm-thick bentonite membrane and dilutions of a produced water sample with an original TDS of 196,250 mg/l obtained from a facility near Loco Hill, New Mexico, operated by an independent. These experiments tested the separation efficiency of the bentonite membrane for each of the dilutions. We found that membrane efficiency decreased with increasing solute concentration and with increasing TDS. The rejection of SO{sub 4}{sup 2-} was greater than Cl{sup -}. This may be because the SO{sub 4}{sup 2-} concentration was much lower than the Cl{sup -} concentration in the waters tested. The cation rejection sequence varied with solute concentration and TDS. The solute rejection sequence for multi-component solutions is difficult to predict for synthetic membranes; it may not be simple for clay membranes either. The permeate flows in our experiments were 4.1 to 5.4% of the total flow. This suggests that very thin clay membranes may be useful for some separations. Work on development of a spiral-wound clay membrane module found that it is difficult to maintain compaction of the membrane if the membrane is rolled and then inserted in the outer tube. A different design was tried using a cylindrical clay membrane and this also proved difficult to assemble with adequate membrane compaction. The next step is to form the membrane in place using hydraulic pressure on a thin slurry of clay in either water or a nonpolar organic solvent such as ethanol. Technology transfer efforts included four manuscripts submitted to peer-reviewed journals, two abstracts, and chairing a session on clays as membranes at the Clay Minerals Society annual meeting.

  12. Reversing the Circulation of Magnetic Vortices

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reversing the Circulation of Magnetic Vortices Print In magnetic media, information is stored in binary form-one or zero, depending on which way the electronic spins are aligned in a given section of the medium. Recently, however, magnetic vortices have drawn scientists toward a new possibility: multibit storage in which each logic unit has four states instead of two and can store twice the information. Each tiny magnetic whirl has a polarity that can point up or down and a circulation that can

  13. Reversing the Circulation of Magnetic Vortices

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reversing the Circulation of Magnetic Vortices Print In magnetic media, information is stored in binary form-one or zero, depending on which way the electronic spins are aligned in a given section of the medium. Recently, however, magnetic vortices have drawn scientists toward a new possibility: multibit storage in which each logic unit has four states instead of two and can store twice the information. Each tiny magnetic whirl has a polarity that can point up or down and a circulation that can

  14. Reversing the Circulation of Magnetic Vortices

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reversing the Circulation of Magnetic Vortices Print In magnetic media, information is stored in binary form-one or zero, depending on which way the electronic spins are aligned in a given section of the medium. Recently, however, magnetic vortices have drawn scientists toward a new possibility: multibit storage in which each logic unit has four states instead of two and can store twice the information. Each tiny magnetic whirl has a polarity that can point up or down and a circulation that can

  15. Reversing the Circulation of Magnetic Vortices

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reversing the Circulation of Magnetic Vortices Print In magnetic media, information is stored in binary form-one or zero, depending on which way the electronic spins are aligned in a given section of the medium. Recently, however, magnetic vortices have drawn scientists toward a new possibility: multibit storage in which each logic unit has four states instead of two and can store twice the information. Each tiny magnetic whirl has a polarity that can point up or down and a circulation that can

  16. Reversing the Circulation of Magnetic Vortices

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reversing the Circulation of Magnetic Vortices Print In magnetic media, information is stored in binary form-one or zero, depending on which way the electronic spins are aligned in a given section of the medium. Recently, however, magnetic vortices have drawn scientists toward a new possibility: multibit storage in which each logic unit has four states instead of two and can store twice the information. Each tiny magnetic whirl has a polarity that can point up or down and a circulation that can

  17. Reversing the Circulation of Magnetic Vortices

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reversing the Circulation of Magnetic Vortices Print In magnetic media, information is stored in binary form-one or zero, depending on which way the electronic spins are aligned in a given section of the medium. Recently, however, magnetic vortices have drawn scientists toward a new possibility: multibit storage in which each logic unit has four states instead of two and can store twice the information. Each tiny magnetic whirl has a polarity that can point up or down and a circulation that can

  18. Reversing the Circulation of Magnetic Vortices

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reversing the Circulation of Magnetic Vortices Print In magnetic media, information is stored in binary form-one or zero, depending on which way the electronic spins are aligned in a given section of the medium. Recently, however, magnetic vortices have drawn scientists toward a new possibility: multibit storage in which each logic unit has four states instead of two and can store twice the information. Each tiny magnetic whirl has a polarity that can point up or down and a circulation that can

  19. Kinetic Stability of the Field Reversed Configuration

    SciTech Connect (OSTI)

    E.V. Belova; R.C. Davidson; H. Ji; and M. Yamada

    2002-07-09

    New computational results are presented which advance the understanding of the stability properties of the Field-Reversed Configuration (FRC). The FRC is an innovative confinement approach that offers a unique fusion reactor potential because of its compact and simple geometry, translation properties, and high plasma beta. One of the most important issues is FRC stability with respect to low-n (toroidal mode number) MHD modes. There is a clear discrepancy between the predictions of standard MHD theory that many modes should be unstable on the MHD time scale, and the observed macroscopic resilience of FRCs in experiments.

  20. A Neutral Beam Pole Shield with Copper Plates and Serviceable...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    A Neutral Beam Pole Shield with Copper Plates and Serviceable Molybdenum Inserts The copper pole shields for the neutral beam lines that have been in service at DIII-D have...

  1. Building America New Homes Case Study: Advanced Extended Plate...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    New Homes Case Study: Advanced Extended Plate and Beam Wall System in a Cold-Climate House ... The Building America research team Home Innovation Research Labs featured this system in a ...

  2. Method for regeneration of electroless nickel plating solution

    DOE Patents [OSTI]

    Eisenmann, E.T.

    1997-03-11

    An electroless nickel(EN)/hypophosphite plating bath is provided employing acetic acid/acetate as a buffer and which is, as a result, capable of perpetual regeneration while avoiding the production of hazardous waste. A regeneration process is provided to process the spent EN plating bath solution. A concentrated starter and replenishment solution is provided for ease of operation of the plating bath. The regeneration process employs a chelating ion exchange system to remove nickel cations from spent EN plating solution. Phosphites are then removed from the solution by precipitation. The nickel cations are removed from the ion exchange system by elution with hypophosphorus acid and the nickel concentration of the eluate adjusted by addition of nickel salt. The treated solution and adjusted eluate are combined, stabilizer added, and the volume of resulting solution reduced by evaporation to form the bath starter and replenishing solution. 1 fig.

  3. ILC TARGET WHEEL RIM FRAGMENT/GUARD PLATE IMPACT ANALYSIS

    SciTech Connect (OSTI)

    Hagler, L

    2008-07-17

    A positron source component is needed for the International Linear Collider Project. The leading design concept for this source is a rotating titanium alloy wheel whose spokes rotate through an intense localized magnetic field. The system is composed of an electric motor, flexible motor/drive-shaft coupling, stainless steel drive-shaft, two Plumber's Block tapered roller bearings, a titanium alloy target wheel, and electromagnet. Surrounding the target wheel and magnet is a steel frame with steel guarding plates intended to contain shrapnel in case of catastrophic wheel failure. Figure 1 is a layout of this system (guard plates not shown for clarity). This report documents the FEA analyses that were performed at LLNL to help determine, on a preliminary basis, the required guard plate thickness for three potential plate steels.

  4. Method for regeneration of electroless nickel plating solution

    DOE Patents [OSTI]

    Eisenmann, Erhard T.

    1997-01-01

    An electroless nickel(EN)/hypophosphite plating bath is provided employing acetic acid/acetate as a buffer and which is, as a result, capable of perpetual regeneration while avoiding the production of hazardous waste. A regeneration process is provided to process the spent EN plating bath solution. A concentrated starter and replenishment solution is provided for ease of operation of the plating bath. The regeneration process employs a chelating ion exchange system to remove nickel cations from spent EN plating solution. Phosphites are then removed from the solution by precipitation. The nickel cations are removed from the ion exchange system by elution with hypophosphorous acid and the nickel concentration of the eluate adjusted by addition of nickel salt. The treated solution and adjusted eluate are combined, stabilizer added, and the volume of resulting solution reduced by evaporation to form the bath starter and replenishing solution.

  5. Thermal Hydraulic Characteristics of Fuel Defects in Plate Type Nuclear

    Office of Scientific and Technical Information (OSTI)

    Research Reactors (Technical Report) | SciTech Connect Thermal Hydraulic Characteristics of Fuel Defects in Plate Type Nuclear Research Reactors Citation Details In-Document Search Title: Thermal Hydraulic Characteristics of Fuel Defects in Plate Type Nuclear Research Reactors × You are accessing a document from the Department of Energy's (DOE) SciTech Connect. This site is a product of DOE's Office of Scientific and Technical Information (OSTI) and is provided as a public service. Visit

  6. Highly conductive, multi-layer composite precursor composition to fuel cell flow field plate or bipolar plate

    DOE Patents [OSTI]

    Jang, Bor Z.; Zhamu, Aruna; Guo, Jiusheng

    2011-02-15

    This invention provides a moldable, multiple-layer composite composition, which is a precursor to an electrically conductive composite flow field plate or bipolar plate. In one preferred embodiment, the composition comprises a plurality of conductive sheets and a plurality of mixture layers of a curable resin and conductive fillers, wherein (A) each conductive sheet is attached to at least one resin-filler mixture layer; (B) at least one of the conductive sheets comprises flexible graphite; and (C) at least one resin-filler mixture layer comprises a thermosetting resin and conductive fillers with the fillers being present in a sufficient quantity to render the resulting flow field plate or bipolar plate electrically conductive with a conductivity no less than 100 S/cm and thickness-direction areal conductivity no less than 200 S/cm.sup.2.

  7. Master plate production for the tile calorimeter extended barrel modules.

    SciTech Connect (OSTI)

    Guarino, V.J.; Hill, N.; Petereit, E.; Price, L.E.; Proudfoot, J.; Wood, K.

    1999-03-10

    Approximately 41,000 master plates (Fig. 1) are required for the Extended Barrel Hadronic Calorimeter for the ATLAS experiment at the LHC. Early in the R&D program associated with the detector, it was recognized that the fabrication of these steel laminations was a significant issue, both in terms of the cost to produce these high precision formed plates, as well as the length of time required to produce all plates for the calorimeter. Two approaches were given serious consideration: laser cutting and die stamping. The Argonne group was a strong supporter of the latter approach and in late 1995 initiated an R&D program to demonstrate the feasibility and cost effectiveness of die stamping these plates by constructing a die and stamping approximately 2000 plates for use in construction of three full size prototype modules. This was extremely successful and die stamping was selected by the group for production of these plates. When the prototype die was constructed it was matched to the calorimeter envelope at that time. This subsequently changed. However with some minor adjustments in the design envelope and a small compromise in terms of instrumented volume, it became possible to use this same die for the production of all master plates for the Tile Calorimeter. Following an extensive series of discussions and an evaluation of the performance of the stamping presses available to our collaborators in Europe, it was decided to ship the US die to CERN for use in stamping master plates for the barrel section of the calorimeter. This was done under the supervision of CERN and JINR, Dubna, and carried out at the TATRA truck plant at Koprivinice, Czech Republic. It was a great success. Approximately 41,000 plates were stamped and fully met specification. Moreover, the production time was significantly reduced by avoiding the need of constructing and then qualifying a second die for use in Europe. This also precluded small geometrical differences between the barrel and extended barrel plates (and therefore submodules) being an issue, with the result that standard submodules are fully exchangeable between the two types of module.

  8. An Integrated Geophysical Analysis Of The Upper Crust Of The...

    Open Energy Info (EERE)

    on upper crustal structure. We used results from surface geological mapping, drill hole data from water wells and geothermal exploration wells, KRISP 85 seismic data for a...

  9. Geothermometry At Upper Hot Creek Ranch Area (Benoit & Blackwell...

    Open Energy Info (EERE)

    Activity Details Location Upper Hot Creek Ranch Area Exploration Technique Geothermometry Activity Date Usefulness useful DOE-funding Unknown Notes Ten water samples were collected...

  10. Upper Midwest Hydrogen Initiative UMHI | Open Energy Information

    Open Energy Info (EERE)

    Midwest Hydrogen Initiative UMHI Jump to: navigation, search Name: Upper Midwest Hydrogen Initiative (UMHI) Place: Minneapolis, Minnesota Zip: 55407 Product: An industry-led,...

  11. Towards reversible basic linear algebra subprograms: A performance study

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Perumalla, Kalyan S.; Yoginath, Srikanth B.

    2014-12-06

    Problems such as fault tolerance and scalable synchronization can be efficiently solved using reversibility of applications. Making applications reversible by relying on computation rather than on memory is ideal for large scale parallel computing, especially for the next generation of supercomputers in which memory is expensive in terms of latency, energy, and price. In this direction, a case study is presented here in reversing a computational core, namely, Basic Linear Algebra Subprograms, which is widely used in scientific applications. A new Reversible BLAS (RBLAS) library interface has been designed, and a prototype has been implemented with two modes: (1) amore » memory-mode in which reversibility is obtained by checkpointing to memory in forward and restoring from memory in reverse, and (2) a computational-mode in which nothing is saved in the forward, but restoration is done entirely via inverse computation in reverse. The article is focused on detailed performance benchmarking to evaluate the runtime dynamics and performance effects, comparing reversible computation with checkpointing on both traditional CPU platforms and recent GPU accelerator platforms. For BLAS Level-1 subprograms, data indicates over an order of magnitude better speed of reversible computation compared to checkpointing. For BLAS Level-2 and Level-3, a more complex tradeoff is observed between reversible computation and checkpointing, depending on computational and memory complexities of the subprograms.« less

  12. Towards reversible basic linear algebra subprograms: A performance study

    SciTech Connect (OSTI)

    Perumalla, Kalyan S.; Yoginath, Srikanth B.

    2014-12-06

    Problems such as fault tolerance and scalable synchronization can be efficiently solved using reversibility of applications. Making applications reversible by relying on computation rather than on memory is ideal for large scale parallel computing, especially for the next generation of supercomputers in which memory is expensive in terms of latency, energy, and price. In this direction, a case study is presented here in reversing a computational core, namely, Basic Linear Algebra Subprograms, which is widely used in scientific applications. A new Reversible BLAS (RBLAS) library interface has been designed, and a prototype has been implemented with two modes: (1) a memory-mode in which reversibility is obtained by checkpointing to memory in forward and restoring from memory in reverse, and (2) a computational-mode in which nothing is saved in the forward, but restoration is done entirely via inverse computation in reverse. The article is focused on detailed performance benchmarking to evaluate the runtime dynamics and performance effects, comparing reversible computation with checkpointing on both traditional CPU platforms and recent GPU accelerator platforms. For BLAS Level-1 subprograms, data indicates over an order of magnitude better speed of reversible computation compared to checkpointing. For BLAS Level-2 and Level-3, a more complex tradeoff is observed between reversible computation and checkpointing, depending on computational and memory complexities of the subprograms.

  13. Digital reverse propagation in focusing Kerr media

    SciTech Connect (OSTI)

    Goy, Alexandre; Psaltis, Demetri

    2011-03-15

    Lenses allow the formation of clear images in homogeneous linear media. Holography is an alternative imaging method, but its use is limited to cases in which it provides an advantage, such as three-dimensional imaging. In nonlinear media, lenses no longer work. The light produces intensity-dependent aberrations. The reverse propagation method used in digital holography to form images from recorded holograms works even in Kerr media [M. Tsang, D. Psaltis, and F. G. Omenetto, Opt. Lett. 28, 1873 (2003).]. The principle has been experimentally demonstrated recently in defocusing media [C. Barsi, W.Wan, and J.W. Fleischer, Nat. Photonics 3, 211 (2009).]. Here, we report experimental results in focusing media.

  14. Review of field-reversed configurations

    SciTech Connect (OSTI)

    Steinhauer, Loren C.

    2011-07-15

    This review addresses field-reversed configurations (FRCs), which are compact-toroidal magnetic systems with little or no toroidal field and very high {beta} (ratio of plasma pressure to magnetic pressure). Although enthusiasm for the FRC has primarily been driven by its potential for an attractive fusion reactor, this review focuses on the physics rather than on technological or engineering aspects. Major advances in both theory and experiment have taken place since the previous comprehensive FRC review in 1988. Even so many questions remain. In particular, even though FRC experiments have exhibited remarkable stability, how well this extrapolates to larger systems remains unresolved. The review considers FRCs under familiar topical categories: equilibrium, global stability, self-organization, transport, formation, and sustainment.

  15. Apparatus for tensile testing plate-type ceramic specimens

    DOE Patents [OSTI]

    Liu, K.C.

    1993-08-24

    Apparatus is described for gripping a plate-type tensile specimen having generally T-shaped end regions in a dynamic tension fatigue testing apparatus comprising an annular housing having an open-ended elongated cavity therein, a plurality of hydraulic piston means supported by the housing in a spaced array about the cavity, and a specimen-supporting plate means overlying the piston means at one end of the elongated cavity and displaceable by said piston means in a longitudinal direction with respect to the longitudinal axis of the cavity, said apparatus for gripping a flat plate-type tensile specimen comprising: a pair of elongated pull rods each having oppositely disposed first and second end regions; a pair of mounting means carried by said plate means with each mounting means for pivotally attaching the first end region of each of said pull rods in a central region of said plate means for supporting said pair of elongated pull rods in a side-by-side relationship along a common longitudinal centerline within said cavity; recess means in the second end region of each of said pull rods in adjacently disposed surface regions thereof with said recess means facing one another and each adapted to receive one side of one of the generally T-shaped end regions of the plate-type tensile specimen; and load-bearing means positionable in each of said recess means and adapted to bear against a shoulder on each side of the generally T-shaped end region of the plate-type tensile specimen when a tensile loading is applied thereon.

  16. Low Cost PEM Fuel Cell Metal Bipolar Plates

    SciTech Connect (OSTI)

    Wang, Conghua

    2013-05-30

    Bipolar plate is an important component in fuel cell stacks and accounts for more than 75% of stack weight and volume. The technology development of metal bipolar plates can effectively reduce the fuel cells stack weight and volume over 50%. The challenge is the metal plate corrosion protection at low cost for the broad commercial applications. This project is aimed to develop innovative technological solutions to overcome the corrosion barrier of low cost metal plates. The feasibility of has been demonstrated and patented (US Patent 7,309,540). The plan is to further reduce the cost, and scale up the technology. The project is built on three pillars: 1) robust experimental evidence demonstrating the feasibility of our technology, 2) a team that consists of industrial leaders in fuel cell stack application, design, and manufactures; 3) a low-risk, significant-milestone driven program that proves the feasibility of meeting program objectives The implementation of this project will reduce the fuel cell stack metal bipolar separator plate cost which accounts 15-21% of the overall stack cost. It will contribute to the market adoption of fuel cell technologies. In addition, this corrosion protection technology can be used similar energy devices, such as batteries and electrolyzers. Therefore, the success of the project will be benefit in broad markets.

  17. Membranes for Reverse-Organic Air Separations | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Membranes for Reverse-Organic Air Separations Membranes for Reverse-Organic Air Separations New Membranes Use Reverse Separation to Reduce Pollutant Emissions Many industrial applications need a process to separate pollutants known as volatile organic compounds (VOCs) from air in order to protect the environment and save energy. One such application is the venting of vapor from underground storage tanks (UST) used in gasoline storage and dispensing. These vapors, which can build up and create

  18. Reversible Alteration of CO2 Adsorption upon Photochemical or...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reversible Alteration of CO2 Adsorption upon Photochemical or Thermal Treatment in a Metal-Organic Framework Previous Next List Jinhee Park , Daqiang Yuan , Khanh T. Pham ,...

  19. Strain-assisted current-induced magnetization reversal in magnetic...

    Office of Scientific and Technical Information (OSTI)

    It is found that the critical current density for in-plane magnetization reversal ... ; Department of Physics, University of Science and Technology Beijing, Beijing 100083 ...

  20. A Reversible Crystallinity-Preserving Phase Transition in Metal...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reversible Crystallinity-Preserving Phase Transition in Metal-Organic Frameworks: Discovery, Mechanistic Studies, and Potential Applications Previous Next List Liu, Dahuan; Liu,...

  1. Advanced Materials for Reversible Solid Oxide Fuel Cell (RSOFC...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fuel Cell (RSOFC), Dual Mode Operation with Low Degradation Advanced Materials for Reversible Solid Oxide Fuel Cell (RSOFC), Dual Mode Operation with Low Degradation Presented ...

  2. Reversible Seeding in Storage Rings (Conference) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    We propose to generate steady-state microbunching in a storage ring with a reversible seeding scheme. High gain harmonic generation (HGHG) and echo-enabled harmonic generation ...

  3. On the reversibility of transitions between closed and open cellular...

    Office of Scientific and Technical Information (OSTI)

    between closed and open cellular convection Citation Details In-Document Search Title: On the reversibility of transitions between closed and open cellular convection The ...

  4. Materials and System Issues with Reversible SOFC | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Cells Workshop Summary Report Advanced Materials for Reversible Solid Oxide Fuel Cell (RSOFC), Dual Mode Operation with Low Degradation Lessons Learned from SOFCSOEC Development...

  5. Fuel cell repeater unit including frame and separator plate

    DOE Patents [OSTI]

    Yamanis, Jean; Hawkes, Justin R; Chiapetta, Jr., Louis; Bird, Connie E; Sun, Ellen Y; Croteau, Paul F

    2013-11-05

    An example fuel cell repeater includes a separator plate and a frame establishing at least a portion of a flow path that is operative to communicate fuel to or from at least one fuel cell held by the frame relative to the separator plate. The flow path has a perimeter and any fuel within the perimeter flow across the at least one fuel cell in a first direction. The separator plate, the frame, or both establish at least one conduit positioned outside the flow path perimeter. The conduit is outside of the flow path perimeter and is configured to direct flow in a second, different direction. The conduit is fluidly coupled with the flow path.

  6. Laser shockwave technique for characterization of nuclear fuel plate interfaces

    SciTech Connect (OSTI)

    Perton, M.; Levesque, D.; Monchalin, J.-P.; Lord, M.; Smith, J. A.; Rabin, B. H.

    2013-01-25

    The US National Nuclear Security Agency is tasked with minimizing the worldwide use of high-enriched uranium. One aspect of that effort is the conversion of research reactors to monolithic fuel plates of low-enriched uranium. The manufacturing process includes hot isostatic press bonding of an aluminum cladding to the fuel foil. The Laser Shockwave Technique (LST) is here evaluated for characterizing the interface strength of fuel plates using depleted Uranium/Mo foils. LST is a non-contact method that uses lasers for the generation and detection of large amplitude acoustic waves and is therefore well adapted to the quality assurance of this process. Preliminary results show a clear signature of well-bonded and debonded interfaces and the method is able to classify/rank the bond strength of fuel plates prepared under different HIP conditions.

  7. Laser Shockwave Technique For Characterization Of Nuclear Fuel Plate Interfaces

    SciTech Connect (OSTI)

    James A. Smith; Barry H. Rabin; Mathieu Perton; Daniel Lévesque; Jean-Pierre Monchalin; Martin Lord

    2012-07-01

    The US National Nuclear Security Agency is tasked with minimizing the worldwide use of high-enriched uranium. One aspect of that effort is the conversion of research reactors to monolithic fuel plates of low-enriched uranium. The manufacturing process includes hot isostatic press bonding of an aluminum cladding to the fuel foil. The Laser Shockwave Technique (LST) is here evaluated for characterizing the interface strength of fuel plates using depleted Uranium/Mo foils. LST is a non-contact method that uses lasers for the generation and detection of large amplitude acoustic waves and is therefore well adapted to the quality assurance of this process. Preliminary results show a clear signature of well-bonded and debonded interfaces and the method is able to classify/rank the bond strength of fuel plates prepared under different HIP conditions.

  8. Laser-Based Characterization of Nuclear Fuel Plates

    SciTech Connect (OSTI)

    James A. Smith; David L. Cottle; Barry H. Rabin

    2013-07-01

    Ensuring the integrity of fuel-clad and clad-clad bonding in nuclear fuels is important for safe reactor operation and assessment of fuel performance, yet the measurement of bond strengths in actual fuels has proved challenging. The laser shockwave technique (LST) originally developed to characterize structural adhesion in composites is being employed to characterize interface strength in a new type of plate fuel being developed at Idaho National Laboratory (INL). LST is a non-contact method that uses lasers for the generation and detection of large-amplitude acoustic waves and is well suited for application to both fresh and irradiated nuclear-fuel plates. This paper will report on initial characterization results obtained from fresh fuel plates manufactured by different processes, including hot isostatic pressing, friction stir welding, and hot rolling.

  9. Low temperature type new TMCP steel plate for LPG carriers

    SciTech Connect (OSTI)

    Suzuki, Shuichi; Bessyo, Kiyoshi; Arimochi, Kazushige; Yajima, Hiroshi; Tada, Masuo; Sakai, Daisuke

    1994-12-31

    New Thermo-Mechanical Control Process (TMCP) steel plate for LPG carriers of completely liquefied type was developed with non-nickel chemistry. The new steel plate has a capability to arrest a long running brittle crack at {minus}46 C (which is the design temperature of the liquefied LPG tanks). A high heat-input one-pass welding can be applied to this steel despite its nickel-less chemistry. These capabilities were enabled by microalloying technology with low aluminum-medium nitrogen-boron, as well as by the advanced Thermo-Mechanical Control Process. This paper describes the new concept of utilizing the trace elements and the evaluation test results as the steel plate for the LPG tank and hull, especially from the standpoints of the fracture safe reliability at high heat input welding and from that of the shop workability.

  10. Scale-up of Carbon/Carbon Bipolar Plates

    SciTech Connect (OSTI)

    David P. Haack

    2009-04-08

    This project was focused upon developing a unique material technology for use in PEM fuel cell bipolar plates. The carbon/carbon composite material developed in this program is uniquely suited for use in fuel cell systems, as it is lightweight, highly conductive and corrosion resistant. The project further focused upon developing the manufacturing methodology to cost-effectively produce this material for use in commercial fuel cell systems. United Technology Fuel Cells Corp., a leading fuel cell developer was a subcontractor to the project was interested in the performance and low-cost potential of the material. The accomplishments of the program included the development and testing of a low-cost, fully molded, net-shape carbon-carbon bipolar plate. The process to cost-effectively manufacture these carbon-carbon bipolar plates was focused on extensively in this program. Key areas for cost-reduction that received attention in this program was net-shape molding of the detailed flow structures according to end-user design. Correlations between feature detail and process parameters were formed so that mold tooling could be accurately designed to meet a variety of flow field dimensions. A cost model was developed that predicted the cost of manufacture for the product in near-term volumes and long-term volumes (10+ million units per year). Because the roduct uses lowcost raw materials in quantities that are less than competitive tech, it was found that the cost of the product in high volume can be less than with other plate echnologies, and can meet the DOE goal of $4/kW for transportation applications. The excellent performance of the all-carbon plate in net shape was verified in fuel cell testing. Performance equivalent to much higher cost, fully machined graphite plates was found.

  11. Fuel cell collector plate and method of fabrication

    DOE Patents [OSTI]

    Braun, James C.; Zabriskie, Jr., John E.; Neutzler, Jay K.; Fuchs, Michel; Gustafson, Robert C.

    2001-01-01

    An improved molding composition is provided for compression molding or injection molding a current collector plate for a polymer electrolyte membrane fuel cell. The molding composition is comprised of a polymer resin combined with a low surface area, highly-conductive carbon and/or graphite powder filler. The low viscosity of the thermoplastic resin combined with the reduced filler particle surface area provide a moldable composition which can be fabricated into a current collector plate having improved current collecting capacity vis-a-vis comparable fluoropolymer molding compositions.

  12. Plasma-assisted catalytic ionization using porous nickel plate

    SciTech Connect (OSTI)

    Oohara, W.; Maeda, T.; Higuchi, T.

    2011-09-15

    Hydrogen atomic pair ions, i.e., H{sup +} and H{sup -} ions, are produced by plasma-assisted catalytic ionization using a porous nickel plate. Positive ions in a hydrogen plasma generated by dc arc discharge are irradiated to the porous plate, and pair ions are produced from the back of the irradiation plane. It becomes clear that the production quantity of pair ions mainly depends on the irradiation current of positive ions and the irradiation energy affects the production efficiency of H{sup -} ions.

  13. Multi-well sample plate cover penetration system

    DOE Patents [OSTI]

    Beer, Neil Reginald

    2011-12-27

    An apparatus for penetrating a cover over a multi-well sample plate containing at least one individual sample well includes a cutting head, a cutter extending from the cutting head, and a robot. The cutting head is connected to the robot wherein the robot moves the cutting head and cutter so that the cutter penetrates the cover over the multi-well sample plate providing access to the individual sample well. When the cutting head is moved downward the foil is pierced by the cutter that splits, opens, and folds the foil inward toward the well. The well is then open for sample aspiration but has been protected from cross contamination.

  14. Recessed impingement insert metering plate for gas turbine nozzles

    DOE Patents [OSTI]

    Itzel, Gary Michael; Burdgick, Steven Sebastian

    2002-01-01

    An impingement insert sleeve is provided that is adapted to be disposed in a coolant cavity defined through a stator vane. The insert has a generally open inlet end and first and second diametrically opposed, perforated side walls. A metering plate having at least one opening defined therethrough for coolant flow is mounted to the side walls to generally transverse a longitudinal axis of the insert, and is disposed downstream from said inlet end. The metering plate improves flow distribution while reducing ballooning stresses within the insert and allowing for a more flexible insert attachment.

  15. Optical processing furnace with quartz muffle and diffuser plate

    DOE Patents [OSTI]

    Sopori, Bhushan L.

    1995-01-01

    An optical furnace for annealing a process wafer comprising a source of optical energy, a quartz muffle having a door to hold the wafer for processing, and a quartz diffuser plate to diffuse the light impinging on the quartz muffle; a feedback system with a light sensor located in the door or wall of the muffle is also provided for controlling the source of optical energy. The quartz for the diffuser plate is surface etched (to give the quartz diffusive qualities) in the furnace during a high intensity burn-in process.

  16. Cold plate with combined inclined impingement and ribbed channels

    DOE Patents [OSTI]

    Parida, Pritish R.

    2015-12-22

    Heat transfer devices and methods for making the same that include a first enclosure having at least one inlet port; a second enclosure having a bottom plate and one or more dividing walls to establish channels, at least one internal surface of each channel having rib structures to create turbulence in a fluid flow; and a jet plate connecting the first enclosure and the second enclosure having impinging jets that convey fluid from the first enclosure to the channels, said impinging jets being set at an angular deviation from normal to cause local acceleration of fluid and to increase a local heat transfer rate.

  17. Liquid suspensions of reversible metal hydrides

    DOE Patents [OSTI]

    Reilly, J.J.; Grohse, E.W.; Winsche, W.E.

    1983-12-08

    The reversibility of the process M + x/2 H/sub 2/ ..-->.. MH/sub x/, where M is a metal hydride former that forms a hydride MH/sub x/ in the presence of H/sub 2/, generally used to store and recall H/sub 2/, is found to proceed under a liquid, thereby to reduce contamination, provide better temperature control and provide in situ mobility of the reactants. Thus, a slurry of particles of a metal hydride former with an inert solvent is subjected to temperature and pressure controlled atmosphere containing H/sub 2/, to store hydrogen (at high pressures) and to release (at low pressures) previously stored hydrogen. The direction of the flow of the H/sub 2/ through the liquid is dependent upon the H/sub 2/ pressure in the gas phase at a given temperature. When the former is above the equilibrium absorption pressure of the respective hydride the reaction proceeds to the right, i.e., the metal hydride is formed and hydrogen is stored in the solid particle. When the H/sub 2/ pressure in the gas phase is below the equilibrium dissociation pressure of the respective hydride the reaction proceeds to the left, the metal hydride is decomposed and hydrogen is released into the gas phase.

  18. A high performance field-reversed configuration

    SciTech Connect (OSTI)

    Binderbauer, M. W.; Tajima, T.; Steinhauer, L. C.; Garate, E.; Tuszewski, M.; Smirnov, A.; Gota, H.; Barnes, D.; Deng, B. H.; Thompson, M. C.; Trask, E.; Yang, X.; Putvinski, S.; Rostoker, N.; Andow, R.; Aefsky, S.; Bolte, N.; Bui, D. Q.; Ceccherini, F.; Clary, R.; and others

    2015-05-15

    Conventional field-reversed configurations (FRCs), high-beta, prolate compact toroids embedded in poloidal magnetic fields, face notable stability and confinement concerns. These can be ameliorated by various control techniques, such as introducing a significant fast ion population. Indeed, adding neutral beam injection into the FRC over the past half-decade has contributed to striking improvements in confinement and stability. Further, the addition of electrically biased plasma guns at the ends, magnetic end plugs, and advanced surface conditioning led to dramatic reductions in turbulence-driven losses and greatly improved stability. Together, these enabled the build-up of a well-confined and dominant fast-ion population. Under such conditions, highly reproducible, macroscopically stable hot FRCs (with total plasma temperature of ∼1 keV) with record lifetimes were achieved. These accomplishments point to the prospect of advanced, beam-driven FRCs as an intriguing path toward fusion reactors. This paper reviews key results and presents context for further interpretation.

  19. Rigid-rotor, field-reversed configuration

    SciTech Connect (OSTI)

    Conti, F. Giammanco, F.; Plasma Diagnostics and Technologies Ltd., Via Giuntini 63, 56023 Navacchio ; Wessel, F. J.; Binderbauer, M. W.; Bolte, N.; Morehouse, M.; Qerushi, A.; Rahman, H. U.; Roche, T.; Slepchenkov, M.

    2014-02-15

    The radial profiles, n(r), B{sub z}(r), and E{sub r}(r), for a Flux-Coil (“inductively driven”), Field-Reversed Configuration (FC-FRC) are measured and compared to the predictions of the Rigid-Rotor Model (RRM), which is an analytic, one-dimensional, time-independent, equilibrium description for the FRC. Injectors mounted on both ends of the confinement vessel provide a pre-fill plasma. Coaxial coils mounted outside the vacuum boundaries of the annular-confinement vessel accelerate the plasma and produce the FRC. The density profile is measured by laser interferometry, the magnetic-field profile using an in-situ probe array, and the electric-field profile using an in-situ, floating-probe array. Free parameters for each profile are measured, which also allow other intrinsic-plasma parameters to be determined, using computer-fit algorithms: null radius, radial thickness, plasma temperature, rotation frequencies, the latter of which are independently verified by spectroscopy. All radial profiles agree with the RRM predictions, for the experimental configuration, parameter regime, and specified-time interval studied here.

  20. Reversible piezomagnetoelectric switching in bulk polycrystalline ceramics

    SciTech Connect (OSTI)

    Stevenson, T. Bennett, J.; Brown, A. P.; Wines, T.; Bell, A. J.; Comyn, T. P.; Smith, R. I.

    2014-08-01

    Magnetoelectric (ME) coupling in materials offer tremendous advantages in device functionality enabling technologies including advanced electronic memory, combining electronic speed, and efficiency with magnetic robustness. However, low cost polycrystalline ME materials are excluded from most commercial applications, operating only at cryogenic temperatures, impractically large electric/magnetic fields, or with low ME coefficients (1-100 mV/cm Oe). Despite this, the technological potential of single compound ME coupling has continued to drive research into multiferroics over the last two decades. Here we show that by manipulating the large induced atomic strain within the polycrystalline, room temperature multiferroic compound 0.7BiFeO{sub 3}–0.3PbTiO{sub 3}, we can induce a reversible, piezoelectric strain controlled ME effect. Employing an in situ neutron diffraction experiment, we have demonstrated that this piezomagnetoelectric effect manifests with an applied electric field >8 kV/mm at the onset of piezoelectric strain, engineered in to the compound by crystallographic phase mixing. This produces a remarkable intrinsic ME coefficient of 1276 mV/cm Oe, due to a strain driven modification to the oxygen sub-lattice, inducing an increase in magnetic moment per Fe{sup 3+} ion of +0.142 μ{sub B}. This work provides a framework for investigations into strain engineered nanostructures to realize low-cost ME devices designed from the atoms up, as well as contributing to the deeper understanding of single phase ME coupling mechanisms.

  1. Reversibly immobilized biological materials in monolayer films on electrodes

    DOE Patents [OSTI]

    Weaver, P.F.; Frank, A.J.

    1993-05-04

    Methods and techniques are described for reversibly binding charged biological particles in a fluid medium to an electrode surface. The methods are useful in a variety of applications. The biological materials may include microbes, proteins, and viruses. The electrode surface may consist of reversibly electroactive materials such as polyvinylferrocene, silicon-linked ferrocene or quinone.

  2. Reversibly immobilized biological materials in monolayer films on electrodes

    DOE Patents [OSTI]

    Weaver, Paul F. (Golden, CO); Frank, Arthur J. (Lakewood, CO)

    1993-01-01

    Methods and techniques are described for reversibly binding charged biological particles in a fluid medium to an electrode surface. The methods are useful in a variety of applications. The biological materials may include microbes, proteins, and viruses. The electrode surface may consist of reversibly electroactive materials such as polyvinylferrocene, silicon-linked ferrocene or quinone.

  3. Reducing current reversal time in electric motor control

    DOE Patents [OSTI]

    Bredemann, Michael V

    2014-11-04

    The time required to reverse current flow in an electric motor is reduced by exploiting inductive current that persists in the motor when power is temporarily removed. Energy associated with this inductive current is used to initiate reverse current flow in the motor.

  4. Method for distinguishing multiple targets using time-reversal acoustics

    DOE Patents [OSTI]

    Berryman, James G.

    2004-06-29

    A method for distinguishing multiple targets using time-reversal acoustics. Time-reversal acoustics uses an iterative process to determine the optimum signal for locating a strongly reflecting target in a cluttered environment. An acoustic array sends a signal into a medium, and then receives the returned/reflected signal. This returned/reflected signal is then time-reversed and sent back into the medium again, and again, until the signal being sent and received is no longer changing. At that point, the array has isolated the largest eigenvalue/eigenvector combination and has effectively determined the location of a single target in the medium (the one that is most strongly reflecting). After the largest eigenvalue/eigenvector combination has been determined, to determine the location of other targets, instead of sending back the same signals, the method sends back these time reversed signals, but half of them will also be reversed in sign. There are various possibilities for choosing which half to do sign reversal. The most obvious choice is to reverse every other one in a linear array, or as in a checkerboard pattern in 2D. Then, a new send/receive, send-time reversed/receive iteration can proceed. Often, the first iteration in this sequence will be close to the desired signal from a second target. In some cases, orthogonalization procedures must be implemented to assure the returned signals are in fact orthogonal to the first eigenvector found.

  5. Characterization and Testing of Monolithic RERTR Fuel Plates

    SciTech Connect (OSTI)

    D. D. Keiser; J. F. Jue; D. E. Burkes

    2007-03-01

    Monolithic fuel plates are being developed for application in research reactors throughout the world. These fuel plates are comprised of a U-Mo alloy foil encased in aluminum alloy cladding. Three different fabrication techniques have been looked at for producing monolithic fuel plates: hot isostatic pressing (HIP), transient liquid phase bonding (TLPB), and friction stir welding (FSW). Of these three techniques, HIP and FSW are currently being emphasized. As part of the development of these fabrication techniques, fuel plates are characterized and tested to determine properties like hardness and the bond strength at the interface between the fuel and cladding. Testing of HIPed samples indicates that the foil/cladding interaction behavior depends on the Mo content in the U-Mo foil, the measured hardness values are quite different for the fuel, cladding, and interaction zone phase and Ti, Zr and Nb are the most effective diffusion barriers. For FSW samples, there is a dependence of the bond strength at the foil/cladding interface on the type of tool that is employed for performing the actual FSW process.

  6. Microwave sintering of single plate-shaped articles

    DOE Patents [OSTI]

    Katz, Joel D. (Los Alamos, NM); Blake, Rodger D. (Tucson, AZ)

    1995-01-01

    Apparatus and method for high temperature sintering of plate-shaped articles of alumina, magnesia, silica, yttria, zirconia, and mixtures thereof using microwave radiation. An article is placed within a sintering structure located within a sintering container which is placed in a microwave cavity for heating. The rates at which heating and cooling take place is controlled.

  7. Computed radiography imaging plates and associated methods of manufacture

    DOE Patents [OSTI]

    Henry, Nathaniel F.; Moses, Alex K.

    2015-08-18

    Computed radiography imaging plates incorporating an intensifying material that is coupled to or intermixed with the phosphor layer, allowing electrons and/or low energy x-rays to impart their energy on the phosphor layer, while decreasing internal scattering and increasing resolution. The radiation needed to perform radiography can also be reduced as a result.

  8. Optical processing furnace with quartz muffle and diffuser plate

    DOE Patents [OSTI]

    Sopori, Bhushan L.

    1996-01-01

    An optical furnace for annealing a process wafer comprising a source of optical energy, a quartz muffle having a door to hold the wafer for processing, and a quartz diffuser plate to diffuse the light impinging on the quartz muffle; a feedback system with a light sensor located in the wall of the muffle is also provided for controlling the source of optical energy.

  9. Microwave sintering of single plate-shaped articles

    DOE Patents [OSTI]

    Katz, J.D.; Blake, R.D.

    1995-07-11

    Apparatus and method are disclosed for high temperature sintering of plate-shaped articles of alumina, magnesia, silica, yttria, zirconia, and mixtures thereof using microwave radiation. An article is placed within a sintering structure located within a sintering container which is placed in a microwave cavity for heating. The rates at which heating and cooling take place is controlled. 2 figs.

  10. Plate-Based Fuel Processing System Final Report

    SciTech Connect (OSTI)

    Carlos Faz; Helen Liu; Jacques Nicole; David Yee

    2005-12-22

    On-board reforming of liquid fuels into hydrogen is an enabling technology that could accelerate consumer usage of fuel cell powered vehicles. The technology would leverage the convenience of the existing gasoline fueling infrastructure while taking advantage of the fuel cell efficiency and low emissions. Commercial acceptance of on-board reforming faces several obstacles that include: (1) startup time, (2) transient response, and (3) system complexity (size, weight and cost). These obstacles are being addressed in a variety of projects through development, integration and optimization of existing fuel processing system designs. In this project, CESI investigated steam reforming (SR), water-gas-shift (WGS) and preferential oxidation (PrOx) catalysts while developing plate reactor designs and hardware where the catalytic function is integrated into a primary surface heat exchanger. The plate reactor approach has several advantages. The separation of the reforming and combustion streams permits the reforming reaction to be conducted at a higher pressure than the combustion reaction, thereby avoiding costly gas compression for combustion. The separation of the two streams also prevents the dilution of the reformate stream by the combustion air. The advantages of the plate reactor are not limited to steam reforming applications. In a WGS or PrOx reaction, the non-catalytic side of the plate would act as a heat exchanger to remove the heat generated by the exothermic WGS or PrOx reactions. This would maintain the catalyst under nearly isothermal conditions whereby the catalyst would operate at its optimal temperature. Furthermore, the plate design approach results in a low pressure drop, rapid transient capable and attrition-resistant reactor. These qualities are valued in any application, be it on-board or stationary fuel processing, since they reduce parasitic losses, increase over-all system efficiency and help perpetuate catalyst durability. In this program, CESI took the initial steam reforming plate-reactor concept and advanced it towards an integrated fuel processing system. A substantial amount of modeling was performed to guide the catalyst development and prototype hardware design and fabrication efforts. The plate-reactor mechanical design was studied in detail to establish design guidelines which would help the plate reactor survive the stresses of repeated thermal cycles (from start-ups and shut-downs). Integrated system performance modeling was performed to predict system efficiencies and determine the parameters with the most significant impact on efficiency. In conjunction with the modeling effort, a significant effort was directed towards catalyst development. CESI developed a highly active, sulfur tolerant, coke resistant, precious metal based reforming catalyst. CESI also developed its own non-precious metal based water-gas shift catalyst and demonstrated the catalysts durability over several thousands of hours of testing. CESI also developed a unique preferential oxidation catalyst capable of reducing 1% CO to < 10 ppm CO over a 35 C operating window through a single pass plate-based reactor. Finally, CESI combined the modeling results and steam reforming catalyst development efforts into prototype hardware. The first generation 3kW(e) prototype was fabricated from existing heat-exchanger plates to expedite the fabrication process. This prototype demonstrated steady state operation ranging from 5 to 100% load conditions. The prototype also demonstrated a 20:1 turndown ratio, 10:1 load transient operation and rapid start-up capability.

  11. Upper Bound on the First Star Formation History (Journal Article...

    Office of Scientific and Technical Information (OSTI)

    Upper Bound on the First Star Formation History Citation Details ... Publication Date: 2014-01-09 OSTI Identifier: 1114151 Report Number(s): SLAC-PUB-15885 Journal ID: ISSN ...

  12. Nonmonotonic pressure evolution of the upper critical field in...

    Office of Scientific and Technical Information (OSTI)

    of the upper critical field, Hc2,c, of single crystalline FeSe was studied using measurements of the interplane resistivity, c, in magnetic fields parallel to tetragonal c axis. ...

  13. Characterization of a geothermal system in the Upper Arkansas...

    Open Energy Info (EERE)

    of a geothermal system in the Upper Arkansas Valley Authors T. Blum, K. van Wijk, L. Liberty, M. Batzle, R. Krahenbuhl, A. Revil and R. Reynolds Conference Society of...

  14. Schlumberger soundings in the Upper Raft River and Raft River...

    Open Energy Info (EERE)

    soundings in the Upper Raft River and Raft River Valleys, Idaho and Utah Jump to: navigation, search OpenEI Reference LibraryAdd to library Report: Schlumberger soundings in the...

  15. Geothermal resources of the Upper San Luis and Arkansas valleys...

    Open Energy Info (EERE)

    resources of the Upper San Luis and Arkansas valleys, Colorado Authors R.H. Pearl and J.K. Barrett Editors Epis, R.C. & Weimer and R.I. Published Colorado School of Mines:...

  16. Laminated exfoliated graphite composite-metal compositions for fuel cell flow field plate or bipolar plate applications

    DOE Patents [OSTI]

    Zhamu, Aruna; Shi, Jinjun; Guo, Jiusheng; Jang, Bor Z

    2014-05-20

    An electrically conductive laminate composition for fuel cell flow field plate or bipolar plate applications. The laminate composition comprises at least a thin metal sheet having two opposed exterior surfaces and a first exfoliated graphite composite sheet bonded to the first of the two exterior surfaces of the metal sheet wherein the exfoliated graphite composite sheet comprises: (a) expanded or exfoliated graphite and (b) a binder or matrix material to bond the expanded graphite for forming a cohered sheet, wherein the binder or matrix material is between 3% and 60% by weight based on the total weight of the first exfoliated graphite composite sheet. Preferably, the first exfoliated graphite composite sheet further comprises particles of non-expandable graphite or carbon in the amount of between 3% and 60% by weight based on the total weight of the non-expandable particles and the expanded graphite. Further preferably, the laminate comprises a second exfoliated graphite composite sheet bonded to the second surface of the metal sheet to form a three-layer laminate. Surface flow channels and other desired geometric features can be built onto the exterior surfaces of the laminate to form a flow field plate or bipolar plate. The resulting laminate has an exceptionally high thickness-direction conductivity and excellent resistance to gas permeation.

  17. Magnetization reversal in TmCrO{sub 3}

    SciTech Connect (OSTI)

    Yoshii, Kenji

    2012-11-15

    Highlights: ► We observed two magnetization reversals in TmCrO{sub 3}. ► The reversal at 28 K is attributed to antiparallel coupling between Cr{sup 3+} and Tm{sup 3+}. ► The other reversal originates from spin reorientation. ► Magnetocaloric effect is observed at the spin reorientation temperature. ► Characteristic magnetization switching is demonstrated. -- Abstract: The perovskite chromite TmCrO{sub 3} shows magnetization reversal at two temperatures. The reversal at ∼28 K is attributed to the antiparallel coupling between Tm{sup 3+} and Cr{sup 3+} moments, while that at the lower temperature (∼6–7 K) is rooted in a rotation of the magnetic moments. Magnetocaloric measurements offer a relatively large entropy change (∼4–5 J kg{sup −1} K{sup −1}) at the lower temperature. The reversal at ∼28 K is accompanied by a sign change of an exchange-bias-like field. The absence of the training effect suggests that this behavior is rooted in unidirectional magnetic anisotropy. The existence of the two magnetization reversals offers the characteristic switching of magnetization. For example, the magnetization is flipped without changing the direction of the applied magnetic field.

  18. Waste treatment by reverse osmosis and membrane processes: Industrial. (Latest citations from the EI Compendex*plus database). NewSearch

    SciTech Connect (OSTI)

    Not Available

    1994-10-01

    The bibliography contains citations concerning the use of membranes in the treatment of industrial wastewaters. Reverse osmosis, ion exchange, electrodialysis, liquid membranes, and ultrafiltration techniques are described. Wastewater treatments for removal of metals, ammonia, sodium compounds, nitrates, fluorides, dyes, biologicals, and radioactive waste using membrane technology are discussed. Applications of this technology to the chemical, petrochemical, pulp, textile, steel, ore treatment, electro-plating, and other wastewater and groundwater-remediation industries are included. (Contains 250 citations and includes a subject term index and title list.)

  19. Fluid flow plate for decreased density of fuel cell assembly

    DOE Patents [OSTI]

    Vitale, Nicholas G.

    1999-01-01

    A fluid flow plate includes first and second outward faces. Each of the outward faces has a flow channel thereon for carrying respective fluid. At least one of the fluids serves as reactant fluid for a fuel cell of a fuel cell assembly. One or more pockets are formed between the first and second outward faces for decreasing density of the fluid flow plate. A given flow channel can include one or more end sections and an intermediate section. An interposed member can be positioned between the outward faces at an interface between an intermediate section, of one of the outward faces, and an end section, of that outward face. The interposed member can serve to isolate the reactant fluid from the opposing outward face. The intermediate section(s) of flow channel(s) on an outward face are preferably formed as a folded expanse.

  20. Fluid flow plate for decreased density of fuel cell assembly

    SciTech Connect (OSTI)

    Vitale, N.G.

    1999-11-09

    A fluid flow plate includes first and second outward faces. Each of the outward faces has a flow channel thereon for carrying respective fluid. At least one of the fluids serves as reactant fluid for a fuel cell of a fuel cell assembly. One or more pockets are formed between the first and second outward faces for decreasing density of the fluid flow plate. A given flow channel can include one or more end sections and an intermediate section. An interposed member can be positioned between the outward faces at an interface between an intermediate section, of one of the outward faces, and an end section, of that outward face. The interposed member can serve to isolate the reactant fluid from the opposing outward face. The intermediate section(s) of flow channel(s) on an outward face are preferably formed as a folded expanse.

  1. Low cost bare-plate solar air collector

    SciTech Connect (OSTI)

    Maag, W.L.; Wenzler, C.J.; Rom, F.E.; VanArsdale, D.R.

    1980-09-01

    The purpose of this project was to develop a low cost, bare-plate collector, determine its performance for a variety of climatic conditions, analyze the economics of this type of solar collector and evaluate specific applications. Two prototype collectors were designed, fabricated and installed into an instrumented test system. Tests were conducted for a period of five months. Results of the tests showed consistent operating efficiencies of 60% or greater with air preheat temperature uses up to 20/sup 0/F for one of the prototypes. The economic analyses indicated that an installed cost of between $5 and $10 per square foot would make this type of solar system economically viable. For the materials of construction and the type of fabrication and installation perceived, these costs for the bare-plate solar collector are believed to be attainable. Specific applications for preheating ventilation air for schools were evaluated and judged to be economically viable.

  2. Magnetic Vortex Core Reversal by Low-Field Excitations

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    millitesla (mT) to reverse the direction of a vortex core. ... and their possible application to data storage technologies. ... Is there a physical limit to how far this process can go? At ...

  3. Reverse phase transformation of martensite to austenite in stainless...

    Office of Scientific and Technical Information (OSTI)

    steels: a 3D phase-field study Citation Details In-Document Search Title: Reverse phase transformation of martensite to austenite in stainless steels: a 3D phase-field ...

  4. Diamond Plates Create Nanostructures through Pressure, Not Chemistry

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Plates Create Nanostructures through Pressure, Not Chemistry - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle

  5. Optical processing furnace with quartz muffle and diffuser plate

    DOE Patents [OSTI]

    Sopori, B.L.

    1996-11-19

    An optical furnace for annealing a process wafer is disclosed comprising a source of optical energy, a quartz muffle having a door to hold the wafer for processing, and a quartz diffuser plate to diffuse the light impinging on the quartz muffle; a feedback system with a light sensor located in the wall of the muffle is also provided for controlling the source of optical energy. 5 figs.

  6. Low-cost solar flat-plate-collector development

    SciTech Connect (OSTI)

    Wilhelm, W.G.

    1981-01-01

    Cost goals were developed for the collector which led to the rejection of conventional approaches and to the exploration of thin-film technology. A thin-film sola absorber suited for high-speed continous-roll manufacture at low cost was designed. The absorber comprises two sheets of aluminum-foil/polymeric-material laminate bonded together at intervals to form channels with water as the heat transfer fluid. Several flat-plate panels were fabricated and tested. (MHR)

  7. On the reversibility of transitions between closed and open cellular

    Office of Scientific and Technical Information (OSTI)

    convection (Journal Article) | SciTech Connect On the reversibility of transitions between closed and open cellular convection Citation Details In-Document Search Title: On the reversibility of transitions between closed and open cellular convection The two-way transition between closed and open cellular convection is addressed in an idealized cloud-resolving modeling framework. A series of cloud-resolving simulations shows that the transition between closed and open cellular states is

  8. On the reversibility of transitions between closed and open cellular

    Office of Scientific and Technical Information (OSTI)

    convection (Journal Article) | SciTech Connect On the reversibility of transitions between closed and open cellular convection Citation Details In-Document Search Title: On the reversibility of transitions between closed and open cellular convection The two-way transition between closed and open cellular convection is addressed in an idealized cloud resolving modeling framework. A series of cloud resolving simulations shows that the transition between closed and open cellular states is

  9. Reversible Magnesium Intercalation into a Layered Oxyfluoride Cathode -

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Joint Center for Energy Storage Research 18, 2015, Research Highlights Reversible Magnesium Intercalation into a Layered Oxyfluoride Cathode Powder diffraction of oxyfluoridecathode with intercalated Mg and capacities of oxyfluorideand oxide cathodes Scientific Achievement Magnesium was reversibly intercalated at room temperature into an oxyfluoride cathode without the co-intercalation of electrolytes or protons and without the formation of unwanted side-products that commonly plague oxide

  10. Rotation Reversal Bifurcation and Energy Confinement Saturation in Tokamak

    Office of Scientific and Technical Information (OSTI)

    Ohmic L -Mode Plasmas (Journal Article) | SciTech Connect Rotation Reversal Bifurcation and Energy Confinement Saturation in Tokamak Ohmic L -Mode Plasmas Citation Details In-Document Search Title: Rotation Reversal Bifurcation and Energy Confinement Saturation in Tokamak Ohmic L -Mode Plasmas Authors: Rice, J. E. ; Cziegler, I. ; Diamond, P. H. ; Duval, B. P. ; Podpaly, Y. A. ; Reinke, M. L. ; Ennever, P. C. ; Greenwald, M. J. ; Hughes, J. W. ; Ma, Y. ; Marmar, E. S. ; Porkolab, M. ;

  11. Brazed aluminum, Plate-fin heat exchangers for OTEC

    SciTech Connect (OSTI)

    Foust, H.D.

    1980-12-01

    Brazed aluminum plate-fin heat exchangers have been available for special applications for over thirty years. The performance, compactness, versatility, and low cost of these heat exchangers has been unequaled by other heat exchanger configuration. The application of brazed aluminum has been highly limited because of necessary restrictions for clean non-corrosive atmospheres. Air and gas separation have provided ideal conditions for accepting brazed aluminum and in turn have benefited by the salient features of these plate-fin heat exchangers. In fact, brazed aluminum and cryogenic gas and air separation have become nearly synonymous. Brazed aluminum in its historic form could not be considered for a seawater atmosphere. However, technology presents a new look of significant importance to OTEC in terms of compactness and cost. The significant technological variation made was to include one-piece hollow extensions for the seawater passages. Crevice corrosion sites are thereby entirely eliminated and pitting corrosion attack will be controlled by an integral and sacrificial layer of a zinc-aluminum alloy. This paper on brazed aluminum plate-fin heat exchangers for OTEC will aquaint the reader with the state-of-art and variations suggested to qualify this form of aluminum for seawater use. In order to verify the desirable cost potential for OTEC, Trane teamed with Westinghouse to perform an OTEC system analysis with this heat exchanger. These results are very promising and reported in detail elsewhere.

  12. Preliminary upper limit on BR(D{sup {+-}}{r_arrow}{pi}{sup {...

    Office of Scientific and Technical Information (OSTI)

    Preliminary upper limit on BR(Dsup +-rarrowpisup +-musup +musup -) Citation Details In-Document Search Title: Preliminary upper limit on BR(Dsup ...

  13. Magnetic design calculation and FRC formation modeling for the field reversed experiment liner

    SciTech Connect (OSTI)

    Dorf, L. A.; Intrator, T. P.; Renneke, R.; Hsu, S. C.; Wurden, G. A.; Awe, T.; Siemon, R.; Semenov, V. E.

    2008-10-01

    Integrated magnetic modeling and design are important to meet the requirements for (1) formation, (2) translation, and (3) compression of a field reversed configuration (FRC) for magnetized target fusion. Off-the-shelf solutions do not exist for many generic design issues. A predictive capability for time-dependent magnetic diffusion in realistically complicated geometry is essential in designing the experiment. An eddy-current code was developed and used to compute the mutual inductances between driven magnetic coils and passive magnetic shields (flux excluder plates) to calculate the self-consistent axisymmetric magnetic fields during the first two stages. The plasma in the formation stage was modeled as an immobile solid cylinder with selectable constant resistivity and magnetic flux that was free to readjust itself. It was concluded that (1) use of experimentally obtained anomalously large plasma resistivity in magnetic diffusion simulations is sufficient to predict magnetic reconnection and FRC formation, (2) comparison of predicted and experimentally observed timescales for FRC Ohmic decay shows good agreement, and (3) for the typical range of resistivities, the magnetic null radius decay rate scales linearly with resistivity. The last result can be used to predict the rate of change in magnetic flux outside of the separatrix (equal to the back-emf loop voltage), and thus estimate a minimum {theta}-coil loop voltage required to form an FRC.

  14. Highly Reversible Mg Insertion in Nanostructured Bi for Mg Ion Batteries

    SciTech Connect (OSTI)

    Shao, Yuyan; Gu, Meng; Li, Xiaolin; Nie, Zimin; Zuo, Pengjian; Li, Guosheng; Liu, Tianbiao L.; Xiao, Jie; Cheng, Yingwen; Wang, Chong M.; Zhang, Jiguang; Liu, Jun

    2014-01-08

    Rechargeable magnesium batteries have attracted wide attention for energy storage. Currently, most studies focus on Mg metal as the anode, but this approach is still limited by the properties of the electrolyte and poor control of the Mg plating/stripping processes.1,2 Here we report the synthesis and application of Bi nanotubes as a high performance anode material for rechargeable Mg ion batteries. The nanostructured Bi anode delivers a high reversible specific capacity (350 mAh/gBi, or 3430 mAh/cm3 Bi), excellent stability, and high columbic efficiency (95 % initial and very close to 100% afterwards). The good performance is attributed to the unique properties of in-situ formed, interconnected nanoporous bismuth. Such nanostructures can effectively accommodate the large volume change without losing electric contact and significantly reduce diffusion length for Mg2+. Significantly, the nanostructured Bi anode can be used with conventional electrolytes which will open new opportunities to study Mg ion battery chemistry and further improve the properties. The performance and the stability of a full cell Mg ion battery have been demonstrated with conventional electrolytes. This work suggests that other high energy density alloy compounds may also be considered for Mg-ion chemistry for high capacity electrode materials.

  15. Real-time sub- Å ngstrom imaging of reversible and irreversible...

    Office of Scientific and Technical Information (OSTI)

    Real-time sub- ngstrom imaging of reversible and irreversible conformations in rhodium catalysts and graphene Title: Real-time sub- ngstrom imaging of reversible and ...

  16. FULL SIZE U-10MO MONOLITHIC FUEL FOIL AND FUEL PLATE FABRICATION-TECHNOLOGY DEVELOPMENT

    SciTech Connect (OSTI)

    G. A. Moore; J-F Jue; B. H. Rabin; M. J. Nilles

    2010-03-01

    Full-size U10Mo foils are being developed for use in high density LEU monolithic fuel plates. The application of a zirconium barrier layer too the foil is applied using a hot co-rolling process. Aluminum clad fuel plates are fabricated using Hot Isostatic Pressing (HIP) or a Friction Bonding (FB) process. An overview is provided of ongoing technology development activities, including: the co-rolling process, foil shearing/slitting and polishing, cladding bonding processes, plate forming, plate-assembly swaging, and fuel plate characterization. Characterization techniques being employed include, Ultrasonic Testing (UT), radiography, and microscopy.

  17. ECOLOGICAL EFFECTS OF CONTAMINANTS IN THE UPPER THREE RUNS INTEGRATOR

    Office of Scientific and Technical Information (OSTI)

    OPERABLE UNIT (Technical Report) | SciTech Connect Technical Report: ECOLOGICAL EFFECTS OF CONTAMINANTS IN THE UPPER THREE RUNS INTEGRATOR OPERABLE UNIT Citation Details In-Document Search Title: ECOLOGICAL EFFECTS OF CONTAMINANTS IN THE UPPER THREE RUNS INTEGRATOR OPERABLE UNIT No abstract prepared. Authors: Paller, M. ; Dyer, S. ; Scott, S. Publication Date: 2011-07-18 OSTI Identifier: 1023278 Report Number(s): SRNL-TR-2011-00201 TRN: US201118%%1082 DOE Contract Number: DE-AC09-08SR22470

  18. Wave-plate structures, power selective optical filter devices, and optical systems using same

    DOE Patents [OSTI]

    Koplow, Jeffrey P.

    2012-07-03

    In an embodiment, an optical filter device includes an input polarizer for selectively transmitting an input signal. The device includes a wave-plate structure positioned to receive the input signal, which includes first and second substantially zero-order, zero-wave plates arranged in series with and oriented at an angle relative to each other. The first and second zero-wave plates are configured to alter a polarization state of the input signal passing in a manner that depends on the power of the input signal. Each zero-wave plate includes an entry and exit wave plate each having a fast axis, with the fast axes oriented substantially perpendicular to each other. Each entry wave plate is oriented relative to a transmission axis of the input polarizer at a respective angle. An output polarizer is positioned to receive a signal output from the wave-plate structure and selectively transmits the signal based on the polarization state.

  19. Categorical Exclusion Determinations: Western Area Power Administration-Upper Great Plains Region

    Broader source: Energy.gov [DOE]

    Categorical Exclusion Determinations issued by Western Area Power Administration-Upper Great Plains Region.

  20. Impact on thin steel plates by tumbling projectiles

    SciTech Connect (OSTI)

    Li, K.; Goldsmith, W.

    1995-12-31

    An experimental, analytical, and numerical investigation into the effects of tumbling projectiles on the impact response of thin 4130 steel target plates was performed. Deformation patterns and failure phenomena as well as the final velocities and trajectories of the projectiles are correlated with initial conditions such as the initial velocity and impact angle (or yaw angle with a zero oblique angle) of the projectile and plate thickness. In the experiments, tumbling motion of the projectiles was induced by impact of a portion of the front face of the projectile with the edge of a massive block placed along the trajectory. Cylinders with a diameter of 12.7 mm, a length of 38.1 mm, and a hardness of R{sub c} 54 were fired at velocities from 400 m/s - 800 m/s. The forward speed of the projectile after tumbling production ranged from 300 m/s-700 m/s. Rotational speeds ranged from 0 rad/s - 3000 rad/s and concomitant impact angles varied from 0{degrees} to 60{degrees}. These parameters were determined from high speed photographic records. The targets were 1.6 mm and 3.2 mm thick. An analytical model developed for thin aluminum target plates was employed in the present study. The model divides the penetration process into three stages: (1) plugging; (2) hole enlargement; and (3) frontal petaling. The processes are quantified using energy dissipation descriptions of the various deformation mechanisms. Numerical simulations of the penetration processes were performed by employment of the program DYNA3D, a nonlinear, three-dimensional finite element code. The material of the target was modeled as elasto-plastic with failure, while the projectile was assumed to be undeformable. The failure criterion of the target is based on the ultimate tensile strain.

  1. Color Anodizing of Titanium Coated Rolled Carbon Steel Plate

    SciTech Connect (OSTI)

    Sarajan, Zohair; Mobarakeh, Hooman Nikbakht; Namiranian, Sohrab

    2011-12-26

    As an important kind of structural materials, the titanium cladded steel plates have the advantages of both metals and have been applied in aviation, spaceflight, chemical and nuclear industries. In this study, the specimens which were prepared under soldering mechanism during rolling were anodized by electrochemical process under a given conditions. The color anodizing takes place by physical phenomenon of color interference. Part of incident light on the titanium oxide is reflected and the other part reflects inside coated titanium layer. Major part of the light which reflects from titanium-oxide interface, reflects again inside of the oxide layer.

  2. U-Mo Plate Blister Anneal Interim Report

    SciTech Connect (OSTI)

    Francine J. Rice; Daniel M. Wachs; Adam B. Robinson; Dennis D. Keiser Jr.; Jan-Fong Jue; Danielle M. Perez; Ross Finlay

    2010-10-01

    Blister thresholds in fuel elements have been a longstanding performance parameter for fuel elements of all types. This behavior has yet to be fully defined for the RERTR U-Mo fuel types. Blister anneal studies that began in 2007 have been expanded to include plates from more recent RERTR experiments. Preliminary data presented in this report encompasses the early generations of the U-Mo fuel systems and the most recent but still developing fuel system. Included is an overview of relevant dispersion fuel systems for the purposes of comparison.

  3. Fuel cell collector plates with improved mass transfer channels

    DOE Patents [OSTI]

    Gurau, Vladimir; Barbir, Frano; Neutzler, Jay K.

    2003-04-22

    A fuel cell collector plate can be provided with one or more various channel constructions for the transport of reactants to the gas diffusion layer and the removal of water therefrom. The outlet channel can be arranged to have a reduced volume compared to the inlet channel, in both interdigitated and discontinuous spiral applications. The land width between an inlet channel and outlet channel can be reduced to improved mass flow rate in regions of deleted reactant concentrations. Additionally or alternatively, the depth of the inlet channel can be reduced in the direction of flow to reduce the diffusion path as the concentration of reactant is reduced.

  4. LARGE ABUNDANCES OF POLYCYCLIC AROMATIC HYDROCARBONS IN TITAN'S UPPER ATMOSPHERE

    SciTech Connect (OSTI)

    Lopez-Puertas, M.; Funke, B.; Garcia-Comas, M.; Dinelli, B. M.; Adriani, A.; D'Aversa, E.; Moriconi, M. L.; Boersma, C.; Allamandola, L. J.

    2013-06-20

    In this paper, we analyze the strong unidentified emission near 3.28 {mu}m in Titan's upper daytime atmosphere recently discovered by Dinelli et al. We have studied it by using the NASA Ames PAH IR Spectroscopic Database. The polycyclic aromatic hydrocarbons (PAHs), after absorbing UV solar radiation, are able to emit strongly near 3.3 {mu}m. By using current models for the redistribution of the absorbed UV energy, we have explained the observed spectral feature and have derived the vertical distribution of PAH abundances in Titan's upper atmosphere. PAHs have been found to be present in large concentrations, about (2-3) Multiplication-Sign 10{sup 4} particles cm{sup -3}. The identified PAHs have 9-96 carbons, with a concentration-weighted average of 34 carbons. The mean mass is {approx}430 u; the mean area is about 0.53 nm{sup 2}; they are formed by 10-11 rings on average, and about one-third of them contain nitrogen atoms. Recently, benzene together with light aromatic species as well as small concentrations of heavy positive and negative ions have been detected in Titan's upper atmosphere. We suggest that the large concentrations of PAHs found here are the neutral counterpart of those positive and negative ions, which hence supports the theory that the origin of Titan main haze layer is located in the upper atmosphere.

  5. Implications of Scheduled ITC Reversion for RPS Compliance: Preliminary Results

    SciTech Connect (OSTI)

    Lowder, Travis; Miller, John; O'Shaughnessy, Eric; Heeter, Jenny

    2015-09-14

    This poster presents DRAFT initial results of a forthcoming NREL analysis. The analysis investigates the impacts of the scheduled investment tax credit (ITC) reversion from 30 percent to 10 percent for certain solar photovoltaic projects. Specifically, it considers whether the reversion will result in increased use of alternative compliance payments (ACPs) in lieu of solar renewable energy credits (SRECs) for renewable portfolio standard (RPS) compliance. The analysis models the effect of a 10 percent ITC on power purchase agreement (PPA) prices for non-residential systems in the eight states with solar carve-outs and solar ACPs. Our preliminary results suggest that states will likely install sufficient capacity to meet long-term targets through SRECs rather than ACPs following the ITC reversion. However, the analysis shows that the ITC reversion could affect project economics such that capacity shortfalls in certain states could temporarily increase the use of ACPs. NREL anticipates publishing a full report of this analysis in fall 2015. credits (SRECs) for renewable portfolio standard (RPS) compliance. The analysis models the effect of a 10 percent ITC on power purchase agreement (PPA) prices for non-residential systems in the eight states with solar carve-outs and solar ACPs. Our preliminary results suggest that states will likely install sufficient capacity to meet long-term targets through SRECs rather than ACPs following the ITC reversion. However, the analysis shows that the ITC reversion could affect project economics such that capacity shortfalls in certain states could temporarily increase the use of ACPs. NREL anticipates publishing a full report of this analysis in fall 2015.

  6. Effects of q -profile structures on intrinsic torque reversals (Journal

    Office of Scientific and Technical Information (OSTI)

    Article) | SciTech Connect Effects of q -profile structures on intrinsic torque reversals Citation Details In-Document Search This content will become publicly available on August 5, 2016 Title: Effects of q -profile structures on intrinsic torque reversals Authors: Lu, Z. X. ; Wang, W. X. ; Diamond, P. H. ; Tynan, G. ; Ethier, S. ; Chen, J. ; Gao, C. ; Rice, J. E. Publication Date: 2015-08-05 OSTI Identifier: 1238907 Grant/Contract Number: AC02-09CH11466; FG02-OER54871 Type: Publisher's

  7. Modified polynomial function model for reversed field pinches

    SciTech Connect (OSTI)

    Shen, W.; Sprott, J.C.

    1990-11-01

    A generalized analytic representation for the magnetic field and current density profiles in a reversed field pinch is proposed. These profiles have zero current density at the wall and finite plasma pressure. The profiles are characterized by two free parameters here taken to be the field reversal parameter (F) and pinch parameter ({Theta}). From the profiles, many useful quantities such as magnetic energy, beta, inductane, resistance and ohmic input power are calculated. These quantities provide a basis for analyzing experimental data and performing electrical circuit modeling of RFP discharges. 19 refs., 9 figs.

  8. Energy current imaging method for time reversal in elastic media

    SciTech Connect (OSTI)

    Anderson, Brian E; Ulrich, Timothy J; Le Bas, Pierre - Yves A; Larmat, Carene; Johnson, Paul A; Guyer, Robert A; Griffa, Michele

    2009-01-01

    An energy current imaging method is presented for use in locating sources of wave energy during the back propagation stage of the time reversal process. During the back propagation phase of an ideal time reversal experiment, wave energy coalesces from all angles of incidence to recreate the source event; after the recreation, wave energy diverges in every direction. An energy current imaging method based on this convergence/divergence behavior has been developed. The energy current imaging method yields a smaller spatial distribution for source reconstruction than is possible with traditional energy imaging methods.

  9. Magnetic Vortex Core Reversal by Low-Field Excitations

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Magnetic Vortex Core Reversal by Low-Field Excitations Magnetic Vortex Core Reversal by Low-Field Excitations Print Wednesday, 28 March 2007 00:00 In micrometer-sized magnetic thin films, the magnetization typically adopts an in-plane, circular configuration known as a magnetic vortex. At the vortex core, the magnetization turns sharply out of the plane, pointing either up or down. Magnetic data storage based on this binary phenomenon is an intriguing concept, but it would require the ability to

  10. Reverse phase transformation of martensite to austenite in stainless

    Office of Scientific and Technical Information (OSTI)

    steels: a 3D phase-field study (Journal Article) | SciTech Connect Reverse phase transformation of martensite to austenite in stainless steels: a 3D phase-field study Citation Details In-Document Search Title: Reverse phase transformation of martensite to austenite in stainless steels: a 3D phase-field study Authors: Yeddu, Hemantha K. [1] ; Lookman, Turab [1] ; Saxena, Avadh B. [1] + Show Author Affiliations Los Alamos National Laboratory Publication Date: 2014-08-19 OSTI Identifier:

  11. Reversible Sigma C-C Bond Formation Between Phenanthroline Ligands

    Office of Scientific and Technical Information (OSTI)

    Activated by (C5Me5)2Yb (Journal Article) | SciTech Connect Reversible Sigma C-C Bond Formation Between Phenanthroline Ligands Activated by (C5Me5)2Yb Citation Details In-Document Search Title: Reversible Sigma C-C Bond Formation Between Phenanthroline Ligands Activated by (C5Me5)2Yb The electronic structure and associated magnetic properties of the 1,10-phenanthroline adducts of Cp*2Yb are dramatically different from those of the 2,2?-bipyridine adducts. The monomeric phenanthroline adducts

  12. E-print Network : Main View : Search Results for Title: "Reversible...

    Office of Scientific and Technical Information (OSTI)

    Reversible control of spin-polarized supercurrents in ferromagnetic Josephson junctions" Author: Banerjee AND Robinson...

  13. UPDATE ON MECHANICAL ANALYSIS OF MONOLITHIC FUEL PLATES

    SciTech Connect (OSTI)

    D. E. Burkes; F. J. Rice; J.-F. Jue; N. P. Hallinan

    2008-03-01

    Results on the relative bond strength of the fuel-clad interface in monolithic fuel plates have been presented at previous RRFM conferences. An understanding of mechanical properties of the fuel, cladding, and fuel / cladding interface has been identified as an important area of investigation and quantification for qualification of monolithic fuel forms. Significant progress has been made in the area of mechanical analysis of the monolithic fuel plates, including mechanical property determination of fuel foils, cladding processed by both hot isostatic pressing and friction bonding, and the fuel-clad composite. In addition, mechanical analysis of fabrication induced residual stress has been initiated, along with a study to address how such stress can be relieved prior to irradiation. Results of destructive examinations and mechanical tests are presented along with analysis and supporting conclusions. A brief discussion of alternative non-destructive evaluation techniques to quantify not only bond quality, but also bond integrity and strength, will also be provided. These are all necessary steps to link out-of-pile observations as a function of fabrication with in-pile behaviours.

  14. SCDAP/RELAP5 Lower Core Plate Model

    SciTech Connect (OSTI)

    Coryell, Eric Wesley; Griffin, F. P.

    1999-10-01

    The SCDAP/RELAP5 computer code is a best-estimate analysis tool for performing nuclear reactor severe accident simulations. This report describes the justification, theory, implementation, and testing of a new modeling capability which will refine the analysis of the movement of molten material from the core region to the vessel lower head. As molten material moves from the core region through the core support structures it may encounter conditions which will cause it to freeze in the region of the lower core plate, delaying its arrival to the vessel head. The timing of this arrival is significant to reactor safety, because during the time span for material relocation to the lower head, the core may be experiencing steam-limited oxidation. The time at which hot material arrives in a coolant-filled lower vessel head, thereby significantly increasing the steam flow rate through the core region, becomes significant to the progression and timing of a severe accident. This report is a revision of a report INEEL/EXT-00707, entitled "Preliminary Design Report for SCDAP/RELAP5 Lower Core Plate Model".

  15. SCDAP/RELAP5 lower core plate model

    SciTech Connect (OSTI)

    Coryell, E.W.; Griffin, F.P.

    1999-09-01

    The SCDAP/RELAP5 computer code is a best-estimate analysis tool for performing nuclear reactor severe accident simulations. This report describes the justification, theory, implementation, and testing of a new modeling capability which will refine the analysis of the movement of molten material from the core region to the vessel lower head. As molten material moves from the core region through the core support structures it may encounter conditions which will cause it to freeze in the region of the lower core plate, delaying its arrival to the vessel head. The timing of this arrival is significant to reactor safety, because during the time span for material relocation to the lower head, the core may be experiencing steam-limited oxidation. The time at which hot material arrives in a coolant-filled lower vessel head, thereby significantly increasing the steam flow rate through the core region, becomes significant to the progression and timing of a severe accident. This report is a revision of a report INEEL/EXT-00707, entitled ``Preliminary Design Report for SCDAP/RELAP5 Lower Core Plate Model''.

  16. Role of plate kinematics and plate-slip-vector partitioning in continental magmatic arcs: Evidence from the Cordillera Blanca, Peru

    SciTech Connect (OSTI)

    McNulty, B.A.; Farber, D.L.; Wallace, G.S.; Lopez, R.; Palacios, O.

    1998-09-01

    New structural and geochronological data from the Cordillera Blanca batholith in the Peruvian Andes, coupled with Nazca-South American plate-slip-vector data, indicate that oblique convergence and associated strike-slip partitioning strongly influenced continental magmatic arc evolution. Both the strain field and mode of magmatism (plutonism vs. volcanism) in the late Miocene Peruvian Andes were controlled by the degree to which the arc-parallel component of the plate slip vector was partitioned into the arc. Strong strike-slip partitioning at ca. 8 Ma produced arc-parallel sinistral shear, strike-slip intercordilleran basins and east-west-oriented tension fractures that facilitated emplacement of the Cordillera Blanca batholith (ca. 8.2 {+-} 0.2 Ma). Periods during which the strike-slip component was not partitioned into the arc (ca. 10 and ca. 7 Ma) were associated with roughly arc-normal contraction and ignimbrite volcanism. The data thus support the contention that contraction within continental magmatic arcs favors volcanism, whereas transcurrent shear favors plutonism. The tie between oblique convergence and batholith emplacement in late Miocene Peruvian Andes provides a modern analogue for batholiths emplaced as the result of transcurrent shear in ancient arcs.

  17. Reversing-counterpulse repetitive-pulse inductive storage circuit

    DOE Patents [OSTI]

    Honig, Emanuel M.

    1987-01-01

    A high-power reversing-counterpulse repetitive-pulse inductive storage and transfer circuit includes an opening switch, a main energy storage coil, a counterpulse capacitor and a small inductor. After counterpulsing the opening switch off, the counterpulse capacitor is recharged by the main energy storage coil before the load pulse is initiated. This gives the counterpulse capacitor sufficient energy for the next counterpulse operation, although the polarity of the capacitor's voltage must be reversed before that can occur. By using a current-zero switch as the counterpulse start switch, the capacitor is disconnected from the circuit (with a full charge) when the load pulse is initiated, preventing the capacitor from depleting its energy store by discharging through the load. After the load pulse is terminated by reclosing the main opening switch, the polarity of the counterpulse capacitor voltage is reversed by discharging the capacitor through a small inductor and interrupting the discharge current oscillation at zero current and peak reversed voltage. The circuit enables high-power, high-repetition-rate operation with reusable switches and features total control (pulse-to-pulse) over output pulse initiation, duration, repetition rate, and, to some extent, risetime.

  18. Simulation studies of nucleation of ferroelectric polarization reversal.

    SciTech Connect (OSTI)

    Brennecka, Geoffrey L.; Winchester, Benjamin Michael

    2014-08-01

    Electric field-induced reversal of spontaneous polarization is the defining characteristic of a ferroelectric material, but the process(es) and mechanism(s) associated with the initial nucleation of reverse-polarity domains are poorly understood. This report describes studies carried out using phase field modeling of LiTaO3, a relatively simple prototype ferroelectric material, in order to explore the effects of either mechanical deformation or optically-induced free charges on nucleation and resulting domain configuration during field-induced polarization reversal. Conditions were selected to approximate as closely as feasible those of accompanying experimental work in order to provide not only support for the experimental work but also ensure that additional experimental validation of the simulations could be carried out in the future. Phase field simulations strongly support surface mechanical damage/deformation as effective for dramatically reducing the overall coercive field (Ec) via local field enhancements. Further, optically-nucleated polarization reversal appears to occur via stabilization of latent nuclei via the charge screening effects of free charges.

  19. Rotational stability of a long field-reversed configuration

    SciTech Connect (OSTI)

    Barnes, D. C. Steinhauer, L. C.

    2014-02-15

    Rotationally driven modes of long systems with dominantly axial magnetic field are considered. We apply the incompressible model and order axial wavenumber small. A recently developed gyro-viscous model is incorporated. A one-dimensional equilibrium is assumed, but radial profiles are arbitrary. The dominant toroidal (azimuthal) mode numbers ℓ=1 and ℓ=2 modes are examined for a variety of non-reversed (B) and reversed profiles. Previous results for both systems with rigid rotor equilibria are reproduced. New results are obtained by incorporation of finite axial wavenumber and by relaxing the assumption of rigid electron and ion rotation. It is shown that the frequently troublesome ℓ=2 field reversed configuration (FRC) mode is not strongly affected by ion kinetic effects (in contrast to non-reversed cases) and is likely stabilized experimentally only by finite length effects. It is also shown that the ℓ=1 wobble mode has a complicated behavior and is affected by a variety of configuration and profile effects. The rotationally driven ℓ=1 wobble is completely stabilized by strong rotational shear, which is anticipated to be active in high performance FRC experiments. Thus, observed wobble modes in these systems are likely not driven by rotation alone.

  20. Reversing-counterpulse repetitive-pulse inductive storage circuit

    DOE Patents [OSTI]

    Honig, E.M.

    1984-06-05

    A high power reversing-counterpulse repetitive-pulse inductive storage and transfer circuit includes an opening switch, a main energy storage coil, a counterpulse capacitor and a small inductor. After counterpulsing the opening switch off, the counterpulse capacitor is recharged by the main energy storage coil before the load pulse is initiated. This gives the counterpulse capacitor sufficient energy for the next counterpulse operation, although the polarity of the capacitor's voltage must be reversed before that can occur. By using a current-zero switch as the counterpulse start switch, the capacitor is disconnected from the circuit (with a full charge) when the load pulse is initiated, preventing the capacitor from depleting its energy store by discharging through the load. After the load pulse is terminated by reclosing the main opening switch, the polarity of the counterpulse capacitor voltage is reversed by discharging the capacitor through a small inductor and interrupting the discharge current oscillation at zero current and peak reversed voltage. The circuit enables high-power, high-repetition-rate operation with reusable switches and features total control (pulse-to-pulse) over output pulse initiation, duration, repetition rate, and, to some extent, risetime.

  1. Reversing-counterpulse repetitive-pulse inductive storage circuit

    DOE Patents [OSTI]

    Honig, E.M.

    1987-02-10

    A high-power reversing-counterpulse repetitive-pulse inductive storage and transfer circuit includes an opening switch, a main energy storage coil, a counterpulse capacitor and a small inductor. After counterpulsing the opening switch off, the counterpulse capacitor is recharged by the main energy storage coil before the load pulse is initiated. This gives the counterpulse capacitor sufficient energy for the next counterpulse operation, although the polarity of the capacitor's voltage must be reversed before that can occur. By using a current-zero switch as the counterpulse start switch, the capacitor is disconnected from the circuit (with a full charge) when the load pulse is initiated, preventing the capacitor from depleting its energy store by discharging through the load. After the load pulse is terminated by reclosing the main opening switch, the polarity of the counterpulse capacitor voltage is reversed by discharging the capacitor through a small inductor and interrupting the discharge current oscillation at zero current and peak reversed voltage. The circuit enables high-power, high-repetition-rate operation with reusable switches and features total control (pulse-to-pulse) over output pulse initiation, duration, repetition rate, and, to some extent, risetime. 10 figs.

  2. Heat Pipe Embedded AlSiC Plates for High Conductivity - Low CTE Heat Spreaders

    SciTech Connect (OSTI)

    Johnson, Matthew ); Weyant, J.; Garner, S. ); Occhionero, M. )

    2010-01-07

    Heat pipe embedded aluminum silicon carbide (AlSiC) plates are innovative heat spreaders that provide high thermal conductivity and low coefficient of thermal expansion (CTE). Since heat pipes are two phase devices, they demonstrate effective thermal conductivities ranging between 50,000 and 200,000 W/m-K, depending on the heat pipe length. Installing heat pipes into an AlSiC plate dramatically increases the plates effective thermal conductivity. AlSiC plates alone have a thermal conductivity of roughly 200 W/m-K and a CTE ranging from 7-12 ppm/ deg C, similar to that of silicon. An equivalent sized heat pipe embedded AlSiC plate has effective thermal conductivity ranging from 400 to 500 W/m-K and retains the CTE of AlSiC.

  3. Motion-induced radiation in a cavity with conducting and permeable plates

    SciTech Connect (OSTI)

    Sarabadani, Jalal; Miri, MirFaez

    2007-05-15

    We consider a conducting and a permeable plate immersed in the vacuum of a scalar field. We calculate the photon production rate when two plates at a distance H oscillate with a frequency {omega}{sub p}. For H{omega}{sub p}/({pi}c)<2, the angular spectrum and photon production rates are significantly different from those of a conventional cavity with two conducting or two permeable plates.

  4. Corrosion-resistant, electrically-conductive plate for use in a fuel cell stack

    DOE Patents [OSTI]

    Carter, J. David; Mawdsley, Jennifer R.; Niyogi, Suhas; Wang, Xiaoping; Cruse, Terry; Santos, Lilia

    2010-04-20

    A corrosion resistant, electrically-conductive, durable plate at least partially coated with an anchor coating and a corrosion resistant coating. The corrosion resistant coating made of at least a polymer and a plurality of corrosion resistant particles each having a surface area between about 1-20 m.sup.2/g and a diameter less than about 10 microns. Preferably, the plate is used as a bipolar plate in a proton exchange membrane (PEMFC) fuel cell stack.

  5. Upper Rio Grande Simulation Model (URGSiM)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Upper Rio Grande Simulation Model (URGSiM) - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management

  6. Vertical dispersion of inertial waves in the upper ocean

    SciTech Connect (OSTI)

    Rubenstein, D.M.

    1983-05-20

    A linear model of the vertical dispersion of near-inertial waves is developed. A porosity distribution near the bottom of the computational domain minimizes bottom reflections and simulates an ocean of the infinite depth. The model is used to show that the vertical dispersion of near-inertial waves in the upper ocean may, under certain conditions, contribute significanlty to the observed rapid decay of inertial oscillations in the surface layer. The kinetic energy of inertial oscillations at mid-latitudes decays with an e folding time scale of 10 days or less, when the parameter lambda(km)/N(cph)d(m) is less than or of the order of unity, where lambda is the wavelength of the wind-generated near-inertial waves, N is the Vaeisaelae frequency in the upper pycnocline, and d is the surface layer thickness. At the top of the pycnocline the model predicts a velocity maximum, which develops as energy propagates downward, out of the surface layer. However, when the upper pycnocline is sufficiently peaked, a resonant frequency interference effect is predicted. This effect modulates the dissipation of surface layer inertial oscillations, and their magnitude after a storm need not decay monotonically. We also make qualitative comparisons with deep-ocean current meter observations taken during the Mixed Layer Experiment (MILE) and with shallow water (105 m) observations taken in the Baltic Sea.

  7. Condensation analysis for plate-frame heat exchangers

    SciTech Connect (OSTI)

    Arman, B.; Rabas, T.J.

    1995-07-01

    A theoretical analysis is presented to predict single component and binary-mixture condensation in plate-frame heat exchangers. A thermodynamic property model based on the Peng-Robinson equation of state was developed for the binary-mixture equilibrium and formulated into a performance prediction program. A set of equations was formulated and a calculation algorithm was developed to predict the local rate of heat and mass transfer for binary mixtures. Friction-factor and heat-transfer-coefficient correlations were developed using experimental data obtained with ammonia condensation. The role of the mass-transfer resistance associated with the condensation process were analyzed for a propane/butane mixture using two limiting cases: (1) no liquid-phase mass-transfer resistance, and (2) infinite liquid-phase mass-transfer resistance. The results show that the vapor-phase mass-transfer resistance is the controlling mechanism for binary-mixture condensation.

  8. Surface modified stainless steels for PEM fuel cell bipolar plates

    DOE Patents [OSTI]

    Brady, Michael P [Oak Ridge, TN; Wang, Heli [Littleton, CO; Turner, John A [Littleton, CO

    2007-07-24

    A nitridation treated stainless steel article (such as a bipolar plate for a proton exchange membrane fuel cell) having lower interfacial contact electrical resistance and better corrosion resistance than an untreated stainless steel article is disclosed. The treated stainless steel article has a surface layer including nitrogen-modified chromium-base oxide and precipitates of chromium nitride formed during nitridation wherein oxygen is present in the surface layer at a greater concentration than nitrogen. The surface layer may further include precipitates of titanium nitride and/or aluminum oxide. The surface layer in the treated article is chemically heterogeneous surface rather than a uniform or semi-uniform surface layer exclusively rich in chromium, titanium or aluminum. The precipitates of titanium nitride and/or aluminum oxide are formed by the nitriding treatment wherein titanium and/or aluminum in the stainless steel are segregated to the surface layer in forms that exhibit a low contact resistance and good corrosion resistance.

  9. Sensor network based vehicle classification and license plate identification system

    SciTech Connect (OSTI)

    Frigo, Janette Rose; Brennan, Sean M; Rosten, Edward J; Raby, Eric Y; Kulathumani, Vinod K

    2009-01-01

    Typically, for energy efficiency and scalability purposes, sensor networks have been used in the context of environmental and traffic monitoring applications in which operations at the sensor level are not computationally intensive. But increasingly, sensor network applications require data and compute intensive sensors such video cameras and microphones. In this paper, we describe the design and implementation of two such systems: a vehicle classifier based on acoustic signals and a license plate identification system using a camera. The systems are implemented in an energy-efficient manner to the extent possible using commercially available hardware, the Mica motes and the Stargate platform. Our experience in designing these systems leads us to consider an alternate more flexible, modular, low-power mote architecture that uses a combination of FPGAs, specialized embedded processing units and sensor data acquisition systems.

  10. Apparatus for tensile testing plate-type ceramic specimens

    DOE Patents [OSTI]

    Liu, Kenneth C.

    1993-01-01

    Apparatus for tensile testing plate-type ceramic specimens having dogbone- or T-shaped end sections without introducing bending stresses in the specimens during the application of a dynamic tensile loading on the specimens is described. A pair of elongated pull rods disposed in a side-by-side relationship are used to grip the shoulders on each T-shaped end section. The pull rods are pivotally attached to a piston-displaceable, disk-shaped member so as to be longitudinally movable with respect to one another effecting the self-alignment thereof with the shoulders on the T-shaped end sections of the specimen to compensate for shoulders being located in different longitudinal positions.

  11. Current conducting end plate of fuel cell assembly

    DOE Patents [OSTI]

    Walsh, Michael M.

    1999-01-01

    A fuel cell assembly has a current conducting end plate with a conductive body formed integrally with isolating material. The conductive body has a first surface, a second surface opposite the first surface, and an electrical connector. The first surface has an exposed portion for conducting current between a working section of the fuel cell assembly and the electrical connector. The isolating material is positioned on at least a portion of the second surface. The conductive body can have support passage(s) extending therethrough for receiving structural member(s) of the fuel cell assembly. Isolating material can electrically isolate the conductive body from the structural member(s). The conductive body can have service passage(s) extending therethrough for servicing one or more fluids for the fuel cell assembly. Isolating material can chemically isolate the one or more fluids from the conductive body. The isolating material can also electrically isolate the conductive body from the one or more fluids.

  12. Phase plate technology for laser marking of magnetic discs

    DOE Patents [OSTI]

    Neuman, B.; Honig, J.; Hackel, L.; Dane, C.B.; Dixit, S.

    1998-10-27

    An advanced design for a phase plate enables the distribution of spots in arbitrarily shaped patterns with very high uniformity and with a continuously or near-continuously varying phase pattern. A continuous phase pattern eliminates large phase jumps typically expected in a grating that provides arbitrary shapes. Large phase jumps increase scattered light outside of the desired pattern, reduce efficiency and can make the grating difficult to manufacture. When manufacturing capabilities preclude producing a fully continuous grating, the present design can be easily adapted to minimize manufacturing errors and maintain high efficiencies. This continuous grating is significantly more efficient than previously described Dammann gratings, offers much more flexibility in generating spot patterns and is easier to manufacture and replicate than a multi-level phase grating. 3 figs.

  13. Phase plate technology for laser marking of magnetic discs

    DOE Patents [OSTI]

    Neuman, Bill; Honig, John; Hackel, Lloyd; Dane, C. Brent; Dixit, Shamasundar

    1998-01-01

    An advanced design for a phase plate enables the distribution of spots in arbitrarily shaped patterns with very high uniformity and with a continuously or near-continuously varying phase pattern. A continuous phase pattern eliminates large phase jumps typically expected in a grating that provides arbitrary shapes. Large phase jumps increase scattered light outside of the desired pattern, reduce efficiency and can make the grating difficult to manufacture. When manufacturing capabilities preclude producing a fully continuous grating, the present design can be easily adapted to minimize manufacturing errors and maintain high efficiencies. This continuous grating is significantly more efficient than previously described Dammann gratings, offers much more flexibility in generating spot patterns and is easier to manufacture and replicate than a multi-level phase grating.

  14. Collimator application for microchannel plate image intensifier resolution improvement

    DOE Patents [OSTI]

    Thomas, Stanley W.

    1996-02-27

    A collimator is included in a microchannel plate image intensifier (MCPI). Collimators can be useful in improving resolution of MCPIs by eliminating the scattered electron problem and by limiting the transverse energy of electrons reaching the screen. Due to its optical absorption, a collimator will also increase the extinction ratio of an intensifier by approximately an order of magnitude. Additionally, the smooth surface of the collimator will permit a higher focusing field to be employed in the MCP-to-collimator region than is currently permitted in the MCP-to-screen region by the relatively rough and fragile aluminum layer covering the screen. Coating the MCP and collimator surfaces with aluminum oxide appears to permit additional significant increases in the field strength, resulting in better resolution.

  15. Fission rate measurements in fuel plate type assembly reactor cores

    SciTech Connect (OSTI)

    Rogers, J.W.

    1988-01-01

    The methods, materials and equipment have been developed to allow extensive and precise measurement of fission rate distributions in water moderated, U-Al fuel plate assembly type reactor cores. Fission rate monitors are accurately positioned in the reactor core, the reactor is operated at a low power for a short time, the fission rate monitors are counted with detectors incorporating automated sample changers and the measurements are converted to fission rate distributions. These measured fission rate distributions have been successfully used as baseline information related to the operation of test and experimental reactors with respect to fission power and distribution, fuel loading and fission experiments for approximately twenty years at the Idaho National Engineering Laboratory (INEL). 7 refs., 8 figs.

  16. Collimator application for microchannel plate image intensifier resolution improvement

    DOE Patents [OSTI]

    Thomas, S.W.

    1996-02-27

    A collimator is included in a microchannel plate image intensifier (MCPI). Collimators can be useful in improving resolution of MCPIs by eliminating the scattered electron problem and by limiting the transverse energy of electrons reaching the screen. Due to its optical absorption, a collimator will also increase the extinction ratio of an intensifier by approximately an order of magnitude. Additionally, the smooth surface of the collimator will permit a higher focusing field to be employed in the MCP-to-collimator region than is currently permitted in the MCP-to-screen region by the relatively rough and fragile aluminum layer covering the screen. Coating the MCP and collimator surfaces with aluminum oxide appears to permit additional significant increases in the field strength, resulting in better resolution. 2 figs.

  17. System Advisor Model: Flat Plate Photovoltaic Performance Modeling Validation Report

    SciTech Connect (OSTI)

    Freeman, J.; Whitmore, J.; Kaffine, L.; Blair, N.; Dobos, A. P.

    2013-12-01

    The System Advisor Model (SAM) is a free software tool that performs detailed analysis of both system performance and system financing for a variety of renewable energy technologies. This report provides detailed validation of the SAM flat plate photovoltaic performance model by comparing SAM-modeled PV system generation data to actual measured production data for nine PV systems ranging from 75 kW to greater than 25 MW in size. The results show strong agreement between SAM predictions and field data, with annualized prediction error below 3% for all fixed tilt cases and below 8% for all one axis tracked cases. The analysis concludes that snow cover and system outages are the primary sources of disagreement, and other deviations resulting from seasonal biases in the irradiation models and one axis tracking issues are discussed in detail.

  18. Double patterning HSQ processes of zone plates for 10 nm diffraction...

    Office of Scientific and Technical Information (OSTI)

    For diffraction-limited zone plates, accuracy better than one-third of the smallest zone ... Sponsoring Org: Materials Sciences Division Country of Publication: United States Language...

  19. Integrated titer plate-injector head for microdrop array preparation, storage and transfer

    DOE Patents [OSTI]

    Swierkowski, Stefan P.

    2000-01-01

    An integrated titer plate-injector head for preparing and storing two-dimensional (2-D) arrays of microdrops and for ejecting part or all of the microdrops and inserting same precisely into 2-D arrays of deposition sites with micrometer precision. The titer plate-injector head includes integrated precision formed nozzles with appropriate hydrophobic surface features and evaporative constraints. A reusable pressure head with a pressure equalizing feature is added to the titer plate to perform simultaneous precision sample ejection. The titer plate-injector head may be utilized in various applications including capillary electrophoresis, chemical flow injection analysis, microsample array preparation, etc.

  20. SUMMARY OF ‘AFIP’ FULL SIZED PLATE IRRADIATIONS IN THE ADVANCED TEST REACTOR

    SciTech Connect (OSTI)

    Robinson, Adam B; Wachs, Daniel M

    2010-03-01

    Recent testing at the Idaho National Laboratory has included four AFIP (ATR Full Size plate In center flux trap Position) experiments. These experiments included both dispersion plates and monolithic plates fabricated by both hot isostatic pressing and friction bonding utilizing both thermally sprayed inter-layers and zirconium barriers. These plates were tested between 100 and 350 w/cm2 at low temperatures and high burn-ups. The post irradiation exams performed have indicated good performance under the conditions tested and a summary of the findings and irradiation history are included herein.

  1. Sheet, strip, and plate, corrosion resistant alloy 67Ni 30Cu, annealed (reaffirmed, 1992). (SAE standard)

    SciTech Connect (OSTI)

    1991-01-01

    This specification covers a corrosion-resistant nickel-copper alloy in the form of sheet, strip, and plate. Alloy: Monel 400 UNS Number: N0440.

  2. Modeling pore corrosion in normally open gold- plated copper connectors.

    SciTech Connect (OSTI)

    Battaile, Corbett Chandler; Moffat, Harry K.; Sun, Amy Cha-Tien; Enos, David George; Serna, Lysle M.; Sorensen, Neil Robert

    2008-09-01

    The goal of this study is to model the electrical response of gold plated copper electrical contacts exposed to a mixed flowing gas stream consisting of air containing 10 ppb H{sub 2}S at 30 C and a relative humidity of 70%. This environment accelerates the attack normally observed in a light industrial environment (essentially a simplified version of the Battelle Class 2 environment). Corrosion rates were quantified by measuring the corrosion site density, size distribution, and the macroscopic electrical resistance of the aged surface as a function of exposure time. A pore corrosion numerical model was used to predict both the growth of copper sulfide corrosion product which blooms through defects in the gold layer and the resulting electrical contact resistance of the aged surface. Assumptions about the distribution of defects in the noble metal plating and the mechanism for how corrosion blooms affect electrical contact resistance were needed to complete the numerical model. Comparisons are made to the experimentally observed number density of corrosion sites, the size distribution of corrosion product blooms, and the cumulative probability distribution of the electrical contact resistance. Experimentally, the bloom site density increases as a function of time, whereas the bloom size distribution remains relatively independent of time. These two effects are included in the numerical model by adding a corrosion initiation probability proportional to the surface area along with a probability for bloom-growth extinction proportional to the corrosion product bloom volume. The cumulative probability distribution of electrical resistance becomes skewed as exposure time increases. While the electrical contact resistance increases as a function of time for a fraction of the bloom population, the median value remains relatively unchanged. In order to model this behavior, the resistance calculated for large blooms has been weighted more heavily.

  3. EVALUATION OF U10MO FUEL PLATE IRRADIATION BEHAVIOR VIA NUMERICAL AND EXPERIMENTAL BENCHMARKING

    SciTech Connect (OSTI)

    Samuel J. Miller; Hakan Ozaltun

    2012-11-01

    This article analyzes dimensional changes due to irradiation of monolithic plate-type nuclear fuel and compares results with finite element analysis of the plates during fabrication and irradiation. Monolithic fuel plates tested in the Advanced Test Reactor (ATR) at Idaho National Lab (INL) are being used to benchmark proposed fuel performance for several high power research reactors. Post-irradiation metallographic images of plates sectioned at the midpoint were analyzed to determine dimensional changes of the fuel and the cladding response. A constitutive model of the fabrication process and irradiation behavior of the tested plates was developed using the general purpose commercial finite element analysis package, Abaqus. Using calculated burn-up profiles of irradiated plates to model the power distribution and including irradiation behaviors such as swelling and irradiation enhanced creep, model simulations allow analysis of plate parameters that are either impossible or infeasible in an experimental setting. The development and progression of fabrication induced stress concentrations at the plate edges was of primary interest, as these locations have a unique stress profile during irradiation. Additionally, comparison between 2D and 3D models was performed to optimize analysis methodology. In particular, the ability of 2D and 3D models account for out of plane stresses which result in 3-dimensional creep behavior that is a product of these components. Results show that assumptions made in 2D models for the out-of-plane stresses and strains cannot capture the 3-dimensional physics accurately and thus 2D approximations are not computationally accurate. Stress-strain fields are dependent on plate geometry and irradiation conditions, thus, if stress based criteria is used to predict plate behavior (as opposed to material impurities, fine micro-structural defects, or sharp power gradients), unique 3D finite element formulation for each plate is required.

  4. Forward and reverse control system for induction motors

    DOE Patents [OSTI]

    Wright, J.T.

    1987-09-15

    A control system for controlling the direction of rotation of a rotor of an induction motor includes an array of five triacs with one of the triacs applying a current of fixed phase to the windings of the rotor and four of the triacs being switchable to apply either hot ac current or return ac current to the stator windings so as to reverse the phase of current in the stator relative to that of the rotor and thereby reverse the direction of rotation of the rotor. Switching current phase in the stator is accomplished by operating the gates of pairs of the triacs so as to connect either hot ac current or return ac current to the input winding of the stator. 1 fig.

  5. Fast chirality reversal of the magnetic vortex by electric current

    SciTech Connect (OSTI)

    Lim, W. L. Liu, R. H.; Urazhdin, S.; Tyliszczak, T.; Erokhin, S. G.; Berkov, D.

    2014-12-01

    The possibility of high-density information encoding in magnetic materials by topologically stable inhomogeneous magnetization configurations such as domain walls, skyrmions, and vortices has motivated intense research into mechanisms enabling their control and detection. While the uniform magnetization states can be efficiently controlled by electric current using magnetic multilayer structures, this approach has proven much more difficult to implement for inhomogeneous states. Here, we report direct observation of fast reversal of magnetic vortex by electric current in a simple planar structure based on a bilayer of spin Hall material Pt with a single microscopic ferromagnetic disk contacted by asymmetric electrodes. The reversal is enabled by a combination of the chiral Oersted field and spin current generated by the nonuniform current distribution in Pt. Our results provide a route for the efficient control of inhomogeneous magnetization configurations by electric current.

  6. Photochromic Metal-Organic Frameworks: Reversible Control of Singlet

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Oxygen Generation | Center for Gas SeparationsRelevant to Clean Energy Technologies | Blandine Jerome Photochromic Metal-Organic Frameworks: Reversible Control of Singlet Oxygen Generation Previous Next List Jihye Park, Dawei Feng, Shuai Yuan and Hong-Cai Zhou, Angew. Chem. Int. Ed. 54, 430-435 (2014) DOI: 10.1002/anie.201408862 Abstract: The controlled generation of singlet oxygen is of great interest owing to its potential applications including industrial wastewater treatment,

  7. Reversible Switching from Antiferro- to Ferromagnetic Behavior by

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Solvent-Mediated, Thermally-Induced Phase Transitions in a Trimorphic MOF-Based Magnetic Sponge System | Center for Gas SeparationsRelevant to Clean Energy Technologies | Blandine Jerome Reversible Switching from Antiferro- to Ferromagnetic Behavior by Solvent-Mediated, Thermally-Induced Phase Transitions in a Trimorphic MOF-Based Magnetic Sponge System Previous Next List Mario Wriedt, Andrey A. Yakovenko, Gregory J. Halder, Andrey V. Prosvirin, Kim R. Dunbar, and Hong-Cai Zhou, J. Am. Chem.

  8. Corrosion/erosion pipe inspection using reverse geometry radiography

    SciTech Connect (OSTI)

    Albert, R.D.

    1996-07-01

    Measurement of corrosion in piping was studied using the Digiray Reverse Geometry X-ray{reg_sign} (RGX{reg_sign}) imaging system during a series of field tests. Sponsored by Shell, Exxon and Mobil oil companies, these were recently carried out at the Shell Martinez refinery facility. Results of the field tests as well as other RGX radiographs taken in the laboratory by Digiray will be described in this report.

  9. Reversible geling co-polymer and method of making

    DOE Patents [OSTI]

    Gutowska, Anna

    2005-12-27

    The present invention is a thereapeutic agent carrier having a thermally reversible gel or geling copolymer that is a linear random copolymer of an [meth-]acrylamide derivative and a hydrophilic comonomer, wherein the linear random copolymer is in the form of a plurality of linear chains having a plurality of molecular weights greater than or equal to a minimum geling molecular weight cutoff and a therapeutic agent.

  10. Cooling by Time Reversal of Atomic Matter Waves

    SciTech Connect (OSTI)

    Martin, J.; Georgeot, B.; Shepelyansky, D. L. [Laboratoire de Physique Theorique, Universite de Toulouse III, CNRS, 31062 Toulouse (France)

    2008-02-01

    We propose an experimental scheme which allows us to realized approximate time reversal of matter waves for ultracold atoms in the regime of quantum chaos. We show that a significant fraction of the atoms return back to their original state, being at the same time cooled down by several orders of magnitude. We give a theoretical description of this effect supported by extensive numerical simulations. The proposed scheme can be implemented with existing experimental setups.

  11. Reversible and irreversible ion migration processes in lead halide

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    perovskites for photovoltaics | MIT-Harvard Center for Excitonics Reversible and irreversible ion migration processes in lead halide perovskites for photovoltaics March 9, 2016 at 4:30 PM/36-462 Eric Hoke Stanford University, Draper Laboratory hoke-eric Lead hybrid perovskites are a promising family of photovoltaic absorber materials that have achieved power conversion efficiencies of over 20%. Lead halide perovskites are ionic materials with a low lattice energy which are unusual properties

  12. Magnetic Vortex Core Reversal by Low-Field Excitations

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Magnetic Vortex Core Reversal by Low-Field Excitations Print In micrometer-sized magnetic thin films, the magnetization typically adopts an in-plane, circular configuration known as a magnetic vortex. At the vortex core, the magnetization turns sharply out of the plane, pointing either up or down. Magnetic data storage based on this binary phenomenon is an intriguing concept, but it would require the ability to flip the vortex cores on demand. Because these structures are highly stable, very

  13. Magnetic Vortex Core Reversal by Low-Field Excitations

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Magnetic Vortex Core Reversal by Low-Field Excitations Print In micrometer-sized magnetic thin films, the magnetization typically adopts an in-plane, circular configuration known as a magnetic vortex. At the vortex core, the magnetization turns sharply out of the plane, pointing either up or down. Magnetic data storage based on this binary phenomenon is an intriguing concept, but it would require the ability to flip the vortex cores on demand. Because these structures are highly stable, very

  14. Magnetic Vortex Core Reversal by Low-Field Excitations

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Magnetic Vortex Core Reversal by Low-Field Excitations Print In micrometer-sized magnetic thin films, the magnetization typically adopts an in-plane, circular configuration known as a magnetic vortex. At the vortex core, the magnetization turns sharply out of the plane, pointing either up or down. Magnetic data storage based on this binary phenomenon is an intriguing concept, but it would require the ability to flip the vortex cores on demand. Because these structures are highly stable, very

  15. Magnetic Vortex Core Reversal by Low-Field Excitations

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Magnetic Vortex Core Reversal by Low-Field Excitations Print In micrometer-sized magnetic thin films, the magnetization typically adopts an in-plane, circular configuration known as a magnetic vortex. At the vortex core, the magnetization turns sharply out of the plane, pointing either up or down. Magnetic data storage based on this binary phenomenon is an intriguing concept, but it would require the ability to flip the vortex cores on demand. Because these structures are highly stable, very

  16. Magnetic Vortex Core Reversal by Low-Field Excitations

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Magnetic Vortex Core Reversal by Low-Field Excitations Print In micrometer-sized magnetic thin films, the magnetization typically adopts an in-plane, circular configuration known as a magnetic vortex. At the vortex core, the magnetization turns sharply out of the plane, pointing either up or down. Magnetic data storage based on this binary phenomenon is an intriguing concept, but it would require the ability to flip the vortex cores on demand. Because these structures are highly stable, very

  17. Magnetic Vortex Core Reversal by Low-Field Excitations

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Magnetic Vortex Core Reversal by Low-Field Excitations Print In micrometer-sized magnetic thin films, the magnetization typically adopts an in-plane, circular configuration known as a magnetic vortex. At the vortex core, the magnetization turns sharply out of the plane, pointing either up or down. Magnetic data storage based on this binary phenomenon is an intriguing concept, but it would require the ability to flip the vortex cores on demand. Because these structures are highly stable, very

  18. Magnetic Vortex Core Reversal by Low-Field Excitations

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Magnetic Vortex Core Reversal by Low-Field Excitations Print In micrometer-sized magnetic thin films, the magnetization typically adopts an in-plane, circular configuration known as a magnetic vortex. At the vortex core, the magnetization turns sharply out of the plane, pointing either up or down. Magnetic data storage based on this binary phenomenon is an intriguing concept, but it would require the ability to flip the vortex cores on demand. Because these structures are highly stable, very

  19. Probiotic formula reverses cow's milk allergies by changing gut bacteria

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of infants | Argonne National Laboratory Probiotic formula reverses cow's milk allergies by changing gut bacteria of infants September 22, 2015 Tweet EmailPrint This press release was originally printed by The University of Chicago Medicine & Biological Sciences. The gut bacteria of infants who developed tolerance to cow's milk after treatment with probiotic formula showed significant differences from those who remained allergic, according to a new study published September 22, 2015, in

  20. Understanding the Initial Stages of Reversible Mg Deposition and Stripping

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    in Inorganic Nonaqueous Electrolytes - Joint Center for Energy Storage Research April 8, 2015, Research Highlights Understanding the Initial Stages of Reversible Mg Deposition and Stripping in Inorganic Nonaqueous Electrolytes MgCl+ Desolvation Diagram Scientific Achievement The chemical species at the Mg-anode surface in the presence of Magnesium Aluminum-Chloro complex (MACC) electrolyte were identified. While solvent molecules (THF and DME) are loosely bound at the Mg(0001) surface, the

  1. Dynamic processes in field-reversed-configuration compact toroids

    SciTech Connect (OSTI)

    Rej, D.J.

    1987-01-01

    In this lecture, the dynamic processes involved in field-reversed configuration (FRC) formation, translation, and compression will be reviewed. Though the FRC is related to the field-reversed mirror concept, the formation method used in most experiments is a variant of the field-reversed THETA-pinch. Formation of the FRC eqilibrium occurs rapidly, usually in less than 20 ..mu..s. The formation sequence consists of several coupled processes: preionization; radial implosion and compression; magnetic field line closure; axial contraction; equilibrium formation. Recent experiments and theory have led to a significantly improved understanding of these processes; however, the experimental method still relies on a somewhat empirical approach which involves the optimization of initial preionization plasma parameters and symmetry. New improvements in FRC formation methods include the use of lower voltages which extrapolate better to larger devices. The axial translation of compact toroid plasmas offers an attractive engineering convenience in a fusion reactor. FRC translation has been demonstrated in several experiments worldwide, and these plasmas are found to be robust, moving at speeds up to the Alfven velocity over distances of up to 16 m, with no degradation in the confinement. Compact toroids are ideal for magnetic compression. Translated FRCs have been compressed and heated by imploding liners. Upcoming experiments will rely on external flux compression to heat a translater FRC at 1-GW power levels. 39 refs.

  2. SPERT Destructive Test - I on Aluminum, Highly Enriched Plate Type Core

    SciTech Connect (OSTI)

    2011-04-05

    SPERT - Special Power Excursion Reactor Tests Destructive Test number 1 On Aluminum, Highly Enriched Plate Type Core. A test studying the behavior of the reactor under destructive conditions on a light water moderated pool-type reactor with a plate-type core.

  3. SPERT Destructive Test - I on Aluminum, Highly Enriched Plate Type Core

    ScienceCinema (OSTI)

    None

    2014-05-07

    SPERT - Special Power Excursion Reactor Tests Destructive Test number 1 On Aluminum, Highly Enriched Plate Type Core. A test studying the behavior of the reactor under destructive conditions on a light water moderated pool-type reactor with a plate-type core.

  4. Image plates as x-ray detectors in plasma physics experiments

    SciTech Connect (OSTI)

    Gales, S.G.; Bentley, C.D.

    2004-10-01

    The performance of image plates based on the photostimulable phosphor BaF(Br,l):Eu{sup 2+} has been investigated and compared with x-ray film. Evaluation of detective quantum efficiency (DQE), sensitivity, dynamic range, and linearity was carried out for several types of commercially available image plate, using the Excalibur soft x-ray calibration facility at AWE. Image plate response was found to be linear over a dynamic range of 5 orders of magnitude. One type of image plate was found to have a number of advantages for soft x-ray detection, with a measured sensitivity 1 order of magnitude greater than that of Kodak Industrex CX and DEF-5 x-ray film. The DQE of this plate was found to be superior to that of film at low [less than 10{sup 3} photons/(50 {mu}m){sup 2}] and high fluxes [greater than 10{sup 4} photons/(50 {mu}m){sup 2}]. The spatial resolution of image plates, scanned with several models of commercial image plate readers, has been evaluated using a USAF resolution test target. The highest spatial resolution measured is 35 {mu}m. Though this is significantly lower than the resolution possible with film, it is sufficient for many applications. Image plates were fielded in a refractive x-ray lens imaging diagnostic on the 1 TW Helen laser and these results are discussed.

  5. Plasma-accelerated flyer-plates for equation of state studies

    SciTech Connect (OSTI)

    Fratanduono, D. E.; Smith, R. F.; Eggert, J. H.; Braun, D. G.; Collins, G. W.; Boehly, T. R.

    2012-07-15

    We report on a new technique to accelerate flyer-plates to high velocities ({approx}5 km/s). In this work, a strong shock is created through direct laser ablation of a thin polyimide foil. Subsequent shock breakout of that foil results in the generation of a plasma characterized by a smoothly increasing density gradient and a strong forward momentum. Stagnation of this plasma onto an aluminum foil and the resultant momentum transfer accelerates a thin aluminum flyer-plate. The aluminum flyer-plate is then accelerated to a peak velocity of {approx}5 km/s before impact with a transparent lithium fluoride (LiF) window. Simulations of the stagnating plasma ramp compression and wave reverberations within the flyer-plate suggest that the temperature at the flyer-plate impact surface is elevated by less than 50 Degree-Sign C. Optical velocimetry is used to measure the flyer-plate velocity and impact conditions enabling the shocked refractive index of LiF to be determined. The results presented here are in agreement with conventional flyer-plate measurements validating the use of plasma-accelerated flyer-plates for equation of state and impact studies.

  6. Simultaneous velocity interferometry and electronic streak photography of laser-launched plates

    SciTech Connect (OSTI)

    Paisley, D.L.; Stahl, D.B.; Garcia, I.A.

    1991-01-01

    Laser-launched, miniature, pseudo-one-dimensional flyer plates are evaluated by three distinct optical techniques that may be incorporated into an optical diagnostic system to give a complete understanding of the plate performance. These techniques are: velocity interferometry, streak photography, and pulsed laser stereo photography. 2 refs., 5 figs.

  7. Low-cost, high-performance solar flat-plate collectors for applications in northern latitudes

    SciTech Connect (OSTI)

    Wilhelm, W.G.

    1981-01-01

    Solar flat plate collector designs have been developed which incorporate high performance polymer film and laminate technology that have a projected manufacturing cost approaching $15/m/sup 2/ and potential thermal performance consistent with the best commercial solar flat plate collectors available today.

  8. EIS-0408: Upper Great Plains Wind Energy Programmatic EIS

    Broader source: Energy.gov [DOE]

    Western Area Power Administration and the U.S. Fish and Wildlife Service, as joint lead agencies, prepared a programmatic EIS that evaluates issues and potential environmental impacts associated with wind energy development within Western’s Upper Great Plains Customer Service Region (Iowa, Minnesota, Montana, Nebraska, North Dakota, and South Dakota) and upon the Service’s landscape-level grassland and wetland easements. Western will use the EIS to implement a comprehensive regional program to manage interconnection requests for wind energy projects.

  9. Project Reports for Upper Skagit Indian Tribe- 2005 Project

    Office of Energy Efficiency and Renewable Energy (EERE)

    The Upper Skagit Indian Tribe lands consist of 550 acres of the Bow Hill Complex with reservation and new development economic lands located in Skagit County, Washington, adjacent to Interstate 5. The strategic energy plan would complete an assessment of the existing economic enterprises including hotel, convention center, and casino, plus potential green energy sources to serve the existing and developing facilities. The strategic energy analysis would complete an assessment of 50 acres acquired in October 2004, to build more low-income houses, and identify energy improvements for the existing fully developed 74 acres of the Helmick Road Reservation established in 1981.

  10. Structural Behavior of Monolithic Fuel Plates During Hot Isostatic Pressing and Annealing

    SciTech Connect (OSTI)

    Pavel G. Medvedev; Hakan Ozaltun

    2010-03-01

    This paper presents results of the stress analysis in the monolithic fuel plates during thermal transients performed using COMSOL finite element analysis software. Large difference in the thermal expansion between the U-Mo foil and Al cladding is the main load origin during heating and cooling of the fuel plates. In addition, the mechanical behavior of the plate is affected by the difference in yield points between the foil and the cladding. This is manifested by the plastic deformation and permanent strains in the cladding, and elastic deformation of the foil. The results show existence of the critical temperature points at which the stresses change from compressive to tensile. The paper highlights principal differences in mechanical behavior between monolithic and dispersion fuel plates, underlines the need for mechanical property data, especially for the U-Mo alloys, and discusses the methodology for mechanical analysis of the monolithic plates.

  11. Simultaneous laser cutting and welding of metal foil to edge of a plate

    DOE Patents [OSTI]

    Pernicka, J.C.; Benson, D.K.; Tracy, C.E.

    1996-03-19

    A method is described for welding an ultra-thin foil to the edge of a thicker sheet to form a vacuum insulation panel comprising the steps of providing an ultra-thin foil having a thickness less than 0.002, providing a top plate having an edge and a bottom plate having an edge, clamping the foil to the edge of the plate wherein the clamps act as heat sinks to distribute heat through the foil, providing a laser, moving the laser relative to the foil and the plate edges to form overlapping weld beads to weld the foil to the plate edges while simultaneously cutting the foil along the weld line formed by the overlapping beads. 7 figs.

  12. Simultaneous laser cutting and welding of metal foil to edge of a plate

    DOE Patents [OSTI]

    Pernicka, John C.; Benson, David K.; Tracy, C. Edwin

    1996-01-01

    A method of welding an ultra-thin foil to the edge of a thicker sheet to form a vacuum insulation panel comprising the steps of providing an ultra-thin foil having a thickness less than 0.002, providing a top plate having an edge and a bottom plate having an edge, clamping the foil to the edge of the plate wherein the clamps act as heat sinks to distribute heat through the foil, providing a laser, moving the laser relative to the foil and the plate edges to form overlapping weld beads to weld the foil to the plate edges while simultaneously cutting the foil along the weld line formed by the overlapping beads.

  13. The overthrusted Zaza Terrane of middle Cretaceous over the North American continental carbonate rocks of upper Jurassic-Lower Cretaceous age - relationships to oil generation

    SciTech Connect (OSTI)

    Echevarria Rodriguez, G.; Castro, J.A.; Amaro, S.V.

    1996-08-01

    The Zaza Terrane is part of the Caribbean plate thrust over the southern edge of the North American basinal and platform carbonate rocks of upper Jurassic-Lower Cretaceous age. Zaza Terrane are volcanic and ophiolitic rocks of Cretaceous age. The ophiolites are mostly serpentines which behave as reservoirs and seals. All Cuban oil fields are either within Zaza Terrane or basinal carbonates underneath, or not far away to the north of the thrust contacts. It appears that the overthrusting of the Zaza Terrane caused the generation of oil in the basinal carbonate source rocks underneath, due to the increase of rock thickness which lowered the oil window to a deeper position and increased the geothermal gradient. Oil generation was after thrusting, during post-orogenic. API gravity of oil is light toward the south and heavy to very heavy to the north. Source rocks to the south are probably of terrigenous origin.

  14. Flow reversal power limit for the HFBR (Technical Report) | SciTech...

    Office of Scientific and Technical Information (OSTI)

    Flow reversal power limit for the HFBR Citation Details In-Document Search Title: Flow reversal power limit for the HFBR You are accessing a document from the Department of ...

  15. High Temperature Reverse By-Pass Diodes Bias and Failures | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Reverse By-Pass Diodes Bias and Failures High Temperature Reverse By-Pass Diodes Bias and Failures Presented at the PV Module Reliability Workshop, February 26 - 27 2013, Golden, ...

  16. Pairing state with a time-reversal symmetry breaking in FeAs...

    Office of Scientific and Technical Information (OSTI)

    Technical Report: Pairing state with a time-reversal symmetry breaking in FeAs-based superconductors Citation Details In-Document Search Title: Pairing state with a time-reversal ...

  17. Unidirectional wireless power transfer using near-field plates

    SciTech Connect (OSTI)

    Imani, Mohammadreza F.; Grbic, Anthony

    2015-05-14

    One of the obstacles preventing wireless power transfer from becoming ubiquitous is their leakage of power: high-amplitude electromagnetic fields that can interfere with other electronic devices, increase health concerns, or hinder power metering. In this paper, we present near-field plates (NFPs) as a novel method to tailor the electromagnetic fields generated by a wireless power transfer system while maintaining high efficiency. NFPs are modulated arrays or surfaces designed to form prescribed near-field patterns. The NFP proposed in this paper consists of an array of loaded loops that are designed to confine the electromagnetic fields of a resonant transmitting loop to the desired direction (receiving loop) while suppressing fields in other directions. The step-by-step design procedure for this device is outlined. Two NFPs are designed and examined in full-wave simulation. Their performance is shown to be in close agreement with the design predictions, thereby verifying the proposed design and operation. A NFP is also fabricated and experimentally shown to form a unidirectional wireless power transfer link with high efficiency.

  18. Successful development and application of high performance plate steels

    SciTech Connect (OSTI)

    Wilson, A.D.

    1995-12-31

    New high performance plate steels (HPPS) are developed in reaction to customer requirements and the availability of essential steelmaking facilities. In this decade significant improvements to steelmaking equipment has made possible the development and production of a variety of new HPPS. Four case studies are presented reviewing the key metallurgical needs and the innovative steel processing that was required. These applications include: (1) Hydrogen Induced Cracking Resistant A516 C-Mn pressure vessel steel with ultra low sulfur and controlled carbon equivalent levels, (2) Temper Embrittlement Resistant A387 Cr-Mo alloy steels for high temperature pressure vessels with low phosphorus, J Factor and sulfur levels with high toughness, (3) formable, weldable, 400HB abrasion resistant alloy steels, which are produced with extra low sulfur levels, reduced carbon and carbon equivalent levels and rigorous heat treatment controls, and (4) weldable, high strength structural steels with low carbon levels, based on Cu-Ni precipitation hardening and A710. Future opportunities for HPPS will result with the installation of additional new steelmaking facilities.

  19. Flow reversal power limit for the HFBR (Technical Report) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Technical Report: Flow reversal power limit for the HFBR Citation Details In-Document Search Title: Flow reversal power limit for the HFBR The High Flux Beam Reactor (HFBR) undergoes a buoyancy-driven reversal of flow in the reactor core following certain postulated accidents. Uncertainties about the afterheat removal capability during the flow reversal has limited the reactor operating power to 30 MW. An experimental and analytical program to address these uncertainties is described in this

  20. Reversible CO Binding in Metal-Organic Frameworks | Center for Gas

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SeparationsRelevant to Clean Energy Technologies | Blandine Jerome Reversible CO Binding in Metal-Organic Frameworks

  1. Combined upper limit for SM Higgs at the Tevatron

    SciTech Connect (OSTI)

    Penning, Bjorn; /Fermilab

    2009-01-01

    We combine results from CDF and D0 on direct searches for a standard model (SM) Higgs boson (H) in p{bar p} collisions at the Fermilab Tevatron at {radical}s = 1.96 TeV. Compared to the previous Higgs Tevatron combination, more data and new channels (WH {yields} {tau}{nu}b{bar b}, VH {yields} {tau}{tau}b{bar b}/jj{tau}{tau}, VH {yields} jjb{bar b}, t{bar t}H {yields} t{bar t}b{bar b}) have been added. Most previously used channels have been reanalyzed to gain sensitivity. We use the latest parton distribution functions and gg {yields} H theoretical cross sections when comparing our limits to the SM predictions. With 2.0-3.6 fb{sup -1} of data analyzed at CDF, and 0.9-4.2 fb{sup -1} at D0, the 95%C.L. upper limits on Higgs boson production are a factor of 2.5 (0.86) times the SM cross section for a Higgs boson mass of m{sub H} = 115 (165) GeV/c{sup 2}. Based on simulation, the corresponding median expected upper limits are 2.4 (1.1). The mass range excluded at 95% C.L. for a SM Higgs has been extended to 160 < m{sub H} < 170 GeV/c{sup 2}.

  2. Effects of constraint on upper shelf fracture toughness

    SciTech Connect (OSTI)

    Joyce, J.A.; Link, R.E.

    1995-12-31

    The upper shelf fracture toughness and tearing resistance of two structural steels, HY-100 and ASTM A533, Gr. B, were determined over a wide range of applied constraint. The constraint conditions were varied by changes in specimen geometry and loading mode. Bend specimens with shallow and deep cracks, compact specimens, and single and double edge notched tension specimens were used in this study. A rotation correction was developed for the single edge notch tension specimen which greatly improved the behavior of the J-R curves determined using this specimen. The experimental results were used to investigate the applicability of the Q and T stress parameters to the correlation of upper shelf initiation toughness, J{sub Ic}, and tearing resistance, T{sub mat}. The J-Q and J-T stress loci, and corresponding plots of material tearing resistance plotted against Q and T, were developed and compared with the expectations of the O`Dowd and Shih and the Betegon and Hancock analyses. The principle conclusions of this work are that J{sub Ic} does not appear to be dependent on T stress or Q while the material tearing resistance, T{sub mat}, is dependent on T stress and Q, with the tearing modulus increasing as constraint decreases.

  3. Experimental method for laser-driven flyer plates for 1-D shocks

    SciTech Connect (OSTI)

    Paisley, D. L.; Luo, S. N.; Swift, D. C.; Loomis, E.; Johnson, R.; Greenfield, S.; Peralta, P.; Koskelo, A.; Tonks, D.

    2007-12-12

    One-dimensional shocks can be generated by impacting flyer plates accelerated to terminal velocities by a confined laser-ablated plasma. Over the past few years, we have developed this capability with our facility-size laser, TRIDENT, capable of {>=}500 Joules at multi-microsecond pulse lengths to accelerate 1-D flyer plates, 8-mm diameter by 0.1-2 mm thick. Plates have been accelerated to terminal velocities of 100 to {>=}500 m/s, with full recovery of the flyer and target for post mortem metallography. By properly tailoring the laser temporal and spatial profile, the expanding confined plasma accelerates the plate away from the transparent sapphire substrate, and decouples the laser parameters from shock pressure profile resulting from the plate impact on a target. Since the flyer plate is in free flight on impact with the target, minimal collateral damage occurs to either. The experimental method to launch these plates to terminal velocity, ancillary diagnostics, and representative experimental data is presented.

  4. Reversible Acid Gas Capture Using CO2-Binding Organic Liquids

    SciTech Connect (OSTI)

    Heldebrant, David J.; Koech, Phillip K.; Yonker, Clement R.; Rainbolt, James E.; Zheng, Feng

    2010-08-31

    Acid gas scrubbing technology is predominantly aqueous alkanolamine based. Of the acid gases, CO2, H2S and SO2 have been shown to be reversible, however there are serious disadvantages with corrosion and high regeneration costs. The primary scrubbing system composed of monoethanolamine is limited to 30% by weight because of the highly corrosive solution. This gravimetric limitation limits the CO2 volumetric (?108 g/L) and gravimetric capacity (?7 wt%) of the system. Furthermore the scrubbing system has a large energy penalty from pumping and heating the excess water required to dissolve the MEA bicarbonate salt. Considering the high specific heat of water (4 j/g-1K-1), low capacities and the high corrosion we set out to design a fully organic solvent that can chemically bind all acid gases i.e. CO2 as reversible alkylcarbonate ionic liquids or analogues thereof. Having a liquid acid gas carrier improves process economics because there is no need for excess solvent to pump and to heat. We have demonstrated illustrated in Figure 1, that CO2-binding organic liquids (CO2BOLs) have a high CO2 solubility paired with a much lower specific heat (<1.5 J/g-1K-1) than aqueous systems. CO2BOLs are a subsection of a larger class of materials known as Binding Organic Liquids (BOLs). Our BOLs have been shown to reversibly bind and release COS, CS2, and SO2, which we denote COSBOLS, CS2BOLs and SO2BOLs. Our BOLs are highly tunable and can be designed for post or pre-combustion gas capture. The design and testing of the next generation zwitterionic CO2BOLs and SO2BOLs are presented.

  5. Reversible Bending Fatigue Testing on Zry-4 Surrogate Rods

    SciTech Connect (OSTI)

    Wang, Jy-An John; Wang, Hong; Bevard, Bruce Balkcom; Howard, Rob L

    2014-01-01

    Testing high-burnup spent nuclear fuel (SNF) presents many challenges in areas such as specimen preparation, specimen installation, mechanical loading, load control, measurements, data acquisition, and specimen disposal because these tasks are complicated by the radioactivity of the test specimens. Research and comparison studies conducted at Oak Ridge National Laboratory (ORNL) resulted in a new concept in 2010 for a U-frame testing setup on which to perform hot-cell reversible bending fatigue testing. Subsequently, the three-dimensional finite element analysis and the engineering design of components were completed. In 2013 the ORNL team finalized the upgrade of the U-frame testing setup and the integration of the U-frame setup into a Bose dual linear motor test bench to develop a cyclic integrated reversible-bending fatigue tester (CIRFT). A final check was conducted on the CIRFT test system in August 2013, and the CIRFT was installed in the hot cell in September 2013 to evaluate both the static and dynamic mechanical response of SNF rods under simulated loads. The fatigue responses of Zircaloy-4 (Zry-4) cladding and the role of pellet pellet and pellet clad interactions are critical to SNF vibration integrity, but such data are not available due to the unavailability of an effective testing system. While the deployment of the developed CIRFT test system in a hot cell will provide the opportunity to generate the data, the use of a surrogate rod has proven quite effective in identifying the underlying deformation mechanism of an SNF composite rod under an equivalent loading condition. This paper presents the experimental results of using surrogate rods under CIRFT reversible cyclic loading. Specifically, monotonic and cyclic bending tests were conducted on surrogate rods made of a Zry-4 tube and alumina pellet inserts, both with and without an epoxy bond.

  6. Synthesis and magnetic reversal of bi-conical Ni nanostructures

    SciTech Connect (OSTI)

    Biziere, N.; Lassalle Ballier, R.; Viret, M.

    2011-09-15

    Template synthesis in polyethylene terephthalate (PET) membranes has been used to grow hour glass shaped nickel nanowires with a constriction in the range of tens of nanometers at the center. Anisotropic magnetoresistance measurements have been performed on a single nanowire to follow magnetization reversal of the structure. The results are explained via 3D micromagnetic simulations showing the appearance of a complex vortex state close to the constriction whose propagation depends on the angle between the cone axis and the applied field. The interest of this original growth process for spintronics is discussed.

  7. Overview of results from the MST reversed field pinch experiment

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    38 Please note that terms and conditions apply. Overview of results from the MST reversed field pinch experiment View the table of contents for this issue, or go to the journal homepage for more 2015 Nucl. Fusion 55 104006 (http://iopscience.iop.org/0029-5515/55/10/104006) Home Search Collections Journals About Contact us My IOPscience | International Atomic Energy Agency Nuclear Fusion Nucl. Fusion 55 (2015) 104006 (8pp) doi:10.1088/0029-5515/55/10/104006 Overview of results from the MST

  8. Error-field penetration in reversed magnetic shear configurations

    SciTech Connect (OSTI)

    Wang, H. H.; Wang, Z. X.; Wang, X. Q. [MOE Key Laboratory of Materials Modification by Beams of the Ministry of Education, School of Physics and Optoelectronic Engineering, Dalian University of Technology, Dalian 116024 (China)] [MOE Key Laboratory of Materials Modification by Beams of the Ministry of Education, School of Physics and Optoelectronic Engineering, Dalian University of Technology, Dalian 116024 (China); Wang, X. G. [School of Physics, Peking University, Beijing 100871 (China)] [School of Physics, Peking University, Beijing 100871 (China)

    2013-06-15

    Error-field penetration in reversed magnetic shear (RMS) configurations is numerically investigated by using a two-dimensional resistive magnetohydrodynamic model in slab geometry. To explore different dynamic processes in locked modes, three equilibrium states are adopted. Stable, marginal, and unstable current profiles for double tearing modes are designed by varying the current intensity between two resonant surfaces separated by a certain distance. Further, the dynamic characteristics of locked modes in the three RMS states are identified, and the relevant physics mechanisms are elucidated. The scaling behavior of critical perturbation value with initial plasma velocity is numerically obtained, which obeys previously established relevant analytical theory in the viscoresistive regime.

  9. New Limit on Time-Reversal Violation in Beta Decay

    SciTech Connect (OSTI)

    Mumm, H. P.; Chupp, T. E.; Cooper, R. L.; Coulter, K. P.; Freedman, S. J.; Fujikawa, B. K.; Garcia, A.; Jones, G. L.; Nico, J. S.; Thompson, A. K.; Trull, C. A.; Wietfeldt, F. E.; Wilkerson, J. F.

    2011-09-02

    We report the results of an improved determination of the triple correlation DP{center_dot}(p{sub e}xp{sub v}) that can be used to limit possible time-reversal invariance in the beta decay of polarized neutrons and constrain extensions to the standard model. Our result is D=[-0.96{+-}1.89(stat){+-}1.01(sys)]x10{sup -4}. The corresponding phase between g{sub A} and g{sub V} is {phi}{sub AV}=180.013 deg. {+-}0.028 deg. (68% confidence level). This result represents the most sensitive measurement of D in nuclear {beta} decay.

  10. Method and apparatus for enhancing microchannel plate data

    DOE Patents [OSTI]

    Thoe, Robert S.

    1987-01-01

    A method and apparatus for determining centroid channel locations is disclosed for use in a system activated by one or more multichannel plates (16,18) and including a linear diode array (24) providing channels of information 1, 2, . . . , n, . . . , N containing signal amplitudes A.sub.n. A source of analog A.sub.n signals (40), and a source of digital clock signals n (48), are provided. Non-zero A.sub.n values are detected in a discriminator (42). A digital signal representing p, the value of n immediately preceding that whereat A.sub.n takes its first non-zero value, is generated in a scaler (50). The analog A.sub.n signals are converted to digital in an analog to digital converter (44). The digital A.sub.n signals are added to produce a digital .SIGMA.A.sub.n signal in a full adder (46). Digital 1, 2, . . . , m signals representing the number of non-zero A.sub.n are produced by a discriminator pulse counter (52). Digital signals representing 1 A.sub.p+ 1, 2 A.sub.p+2, . . . , m A.sub.p+m are produced by pairwise multiplication in multiplier (54). These signals are added in multiplier summer (56) to produce a digital .SIGMA.nA.sub.n -p.SIGMA.A.sub.n signal. This signal is divided by the digital .SIGMA.A.sub.n signal in divider (58) to provide a digital (.SIGMA.nA.sub.n /.SIGMA.A.sub.n) -p signal. Finally, this last signal is added to the digital p signal in an offset summer (60) to provide .SIGMA.nA.sub.n /.SIGMA.A.sub.n, the centroid channel locations.

  11. 21-PWR WASTE PACKAGE WITH ABSORBER PLATES LOADING CURVE EVALUATION

    SciTech Connect (OSTI)

    J.M. Scaglione

    2004-12-17

    The objective of this calculation is to evaluate the required minimum burnup as a function of initial pressurized water reactor (PWR) assembly enrichment that would permit loading of spent nuclear fuel into the 21 PWR waste package with absorber plates design as provided in Attachment IV. This calculation is an example of the application of the methodology presented in the ''Disposal Criticality Analysis Methodology Topical Report'' (YMP 2003). The scope of this calculation covers a range of enrichments from 0 through 5.0 weight percent U-235, and a burnup range of 0 through 45 GWd/MTU. Higher burnups were not necessary because 45 GWd/MTU was high enough for the loading curve determination. This activity supports the validation of the use of burnup credit for commercial spent nuclear fuel applications. The intended use of these results will be in establishing PWR waste package configuration loading specifications. Limitations of this evaluation are as follows: (1) The results are based on burnup credit for actinides and selected fission products as proposed in YMP (2003, Table 3-1) and referred to as the ''Principal Isotopes''. Any change to the isotope listing will have a direct impact on the results of this report. (2) The results are based on 1.5 wt% Gd in the Ni-Gd Alloy material and having no tuff inside the waste package. If the Gd loading is reduced or a process to introduce tuff inside the waste package is defined, then this report would need to be reevaluated based on the alternative materials. This calculation is subject to the ''Quality Assurance Requirements and Description'' (QARD) (DOE 2004) because it concerns engineered barriers that are included in the ''Q-List'' (BSC 2004k, Appendix A) as items important to safety and waste isolation.

  12. Method and apparatus for enhancing microchannel plate data

    DOE Patents [OSTI]

    Thoe, R.S.

    1983-10-24

    A method and apparatus for determining centroid channel locations are disclosed for use in a system activated by one or more multichannel plates and including a linear diode array providing channels of information 1, 2, ...,n, ..., N containing signal amplitudes A/sub n/. A source of analog A/sub n/ signals, and a source of digital clock signals n, are provided. Non-zero A/sub n/ values are detected in a discriminator. A digital signal representing p, the value of n immediately preceding that whereat A/sub n/ takes its first non-zero value, is generated in a scaler. The analog A/sub n/ signals are converted to digital in an analog to digital converter. The digital A/sub n/ signals are added to produce a digital ..sigma..A/sub n/ signal in a full adder. Digital 1, 2, ..., m signals representing the number of non-zero A/sub n/ are produced by a discriminator pulse counter. Digital signals representing 1 A/sub p+1/, 2 A/sub p+2/, ..., m A/sub p+m/ are produced by pairwise multiplication in multiplier. These signal are added in multiplier summer to produce a digital ..sigma..nA/sub n/ - p..sigma..A/sub n/ signal. This signal is divided by the digital ..sigma..A/sub n/ signal in divider to provide a digital (..sigma..nA/sub n//..sigma..A/sub n/) -p signal. Finally, this last signal is added to the digital p signal in an offset summer to provide ..sigma..nA/sub n//..sigma..A/sub n/, the centroid channel locations.

  13. Thickness effects on the plastic collapse of perforated plates with triangular penetration patterns

    SciTech Connect (OSTI)

    Gordon, J.L.; Jones, D.P.; Holliday, J.E.

    2000-03-01

    This paper investigates the effects of plate thickness on the accuracy of limit load solutions obtained using an elastic-perfectly plastic [EPP] equivalent solid [EQS] procedure for flat perforated plates with a triangular array of penetrations. The EQS approach for limit loads is based on an EQS collapse surface that is valid for generalized plane strain. This assumption is applicable for very thick plates but is known to be less reasonable for very thin plates where plane stress may be a better assumption. The limits of applicability of the generalized plane strain assumption are investigated by obtaining limit load solutions for perforated plates of various thicknesses that are subjected to in-plane and bending loads. Plastic limit load solutions obtained using three-dimensional EPP finite element analysis [FEA] of models which include each penetration explicitly are compared with solutions obtained using the EQS approximation. The penetration pattern chosen for this study has a ligament efficiency (ligament width-to-pitch ratio, h/P) of 0.32. For plates thicker than the pitch, the limit load calculated using the EQS method for both in-plane and bending loads is shown to be very accurate (within 4%) of the limit load calculated for the explicit model. On the other hand, for thin plates (t/P< 2), the EQS limit load is 5% greater than the explicit limit load for bending and 8% greater than the explicit limit load for in-plane loads. For thinner plates, the collapse surface is tied to the local geometry deformation and, hence, an equivalent solid plate representation of plastic collapse is a function of deformation mode and thickness.

  14. Laser/matter interactions by laser-launched plates and direct laser shocks

    SciTech Connect (OSTI)

    Paisley, Dennis L.; Swift, D. C.; Kopp, R. A.; Montgomery, D. S.; Johnson, R. P.; Munson, C. P.; Letzring, S. A.; Niemczura, J. G.

    2003-01-01

    Explosives, gas guns, laser-launched flyer plates, and direct laser-irradiation can be used to generate shocks and high-stress in materials. Each method has a unique diameter and thickness of shock that can be generated. In past years, small laboratory lasers have been used to launch flyer plates 2 - 200-pm thick to terminal velocities 0.1 to 5 k d s . Over the past few years we have been using our TRIDENT laser facility (1kJ in 0.2 to 2ps) to accelerate larger diameter (8 mm) and thicker (0.1 - 1.5 mm) flyer plates. These larger diameters and thicker one-dimensional plates more closely compliment traditional experimental methods such as gas guns. The 8-mm diameter and 1-mm thick flyer plates can impart shocks in metals for constitutive dynamic property measurements. The versatility of laser-driven plates permits spatial and temporal profiles of the flyer plate impact on sample targets. LASNEX models and parameters of the laser drive can be used to optimize optical coupling efficiency. The flyer plate launch, acceleration, terminal velocity, and, depending on the experiment, flyer plate impact on to target materials are recorded using point-interferometry (VISAR), and line-imaging interferometry. These high speed optical and laser experimental methods will be described along with ancillary methods, and material data. Constitutive properties of bulk materials, rate effects, and grain size and/or orientation have been studied for several metals including copper, beryllium, gold, and some alloys.

  15. Method and apparatus for actively controlling a micro-scale flexural plate wave device

    DOE Patents [OSTI]

    Dohner, Jeffrey L.

    2001-01-01

    An actively controlled flexural plate wave device provides a micro-scale pump. A method of actively controlling a flexural plate wave device produces traveling waves in the device by coordinating the interaction of a magnetic field with actively controlled currents. An actively-controlled flexural plate wave device can be placed in a fluid channel and adapted for use as a micro-scale fluid pump to cool or drive micro-scale systems, for example, micro-chips, micro-electrical-mechanical devices, micro-fluid circuits, or micro-scale chemical analysis devices.

  16. Study of imaging plate detector sensitivity to 5-18 MeV electrons (Journal

    Office of Scientific and Technical Information (OSTI)

    Article) | SciTech Connect Study of imaging plate detector sensitivity to 5-18 MeV electrons Citation Details In-Document Search Title: Study of imaging plate detector sensitivity to 5-18 MeV electrons Imaging plates (IPs) are commonly used as passive detectors in laser-plasma experiments. We calibrated at the ELSA electron beam facility (CEA DIF) the five different available types of IPs (namely, MS-SR-TR-MP-ND) to electrons from 5 to 18 MeV. In the context of diagnostic development for the

  17. Building America New Homes Case Study: Advanced Extended Plate and Beam

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Wall System in a Cold-Climate House | Department of Energy New Homes Case Study: Advanced Extended Plate and Beam Wall System in a Cold-Climate House Building America New Homes Case Study: Advanced Extended Plate and Beam Wall System in a Cold-Climate House A zero energy ready home was recently completed that features an innovative wall system. This highly insulated (high-R) light-frame wall system, called the extended plate and beam, is for use above grade in residential buildings. The

  18. Demonstration of 12 nm resolution Fresnel zone plate lens based soft x-ray microscopy

    SciTech Connect (OSTI)

    Chao, W.; Kim, J.; Rekawa, S.; Fischer, P.; Anderson, E. H.

    2009-06-05

    To extend soft x-ray microscopy to a resolution of order 10 nm or better, we developed a new nanofabrication process for Fresnel zone plate lenses. The new process, based on the double patterning technique, has enabled us to fabricate high quality gold zone plates with 12 nm outer zones. Testing of the zone plate with the full-field transmission x-ray microscope, XM-1, in Berkeley, showed that the lens clearly resolved 12 nm lines and spaces. This result represents a significant step towards 10 nm resolution and beyond.

  19. Disruption Analysis and Response Implicattions of Passive Plates for the NSTX Upgrade

    SciTech Connect (OSTI)

    Yuhu Zhai, Peter Titus, Art Brooks, and Ron Hatcher

    2012-08-27

    The NSTX upgrade project requires analysis qualifications of existing vacuum vessel and passive stabilizing plates for increased plasma performance. Vertical stability is critically dependent on the passive conducting structure that surrounds the plasma. In this paper, the passive conducting structure is analyzed for the upgrade condition during plasma disruption to ensure the level of stress in the stabilizing plates and the fastener is within its design limits. The counter-bore of the passive plates for bolting is evaluated in details and counter-bore bushing is redesigned to prevent shear failure during disruptions as a result of high pulling and pushing forces, particularly for support at the corner bolts

  20. ATOMIC CARBON IN THE UPPER ATMOSPHERE OF TITAN

    SciTech Connect (OSTI)

    Zhang, X.; Yung, Y. L.; Ajello, J. M.

    2010-01-01

    The atomic carbon emission C I line feature at 1657 A ({sup 3} P {sup 0} {sub J}-{sup 3} P{sub J} ) in the upper atmosphere of Titan is first identified from the airglow spectra obtained by the Cassini Ultra-violet Imaging Spectrograph. A one-dimensional photochemical model of Titan is used to study the photochemistry of atomic carbon on Titan. Reaction between CH and atomic hydrogen is the major source of atomic carbon, and reactions with hydrocarbons (C{sub 2}H{sub 2} and C{sub 2}H{sub 4}) are the most important loss processes. Resonance scattering of sunlight by atomic carbon is the dominant emission mechanism. The emission intensity calculations based on model results show good agreement with the observations.

  1. The 125 MW Upper Mahiao geothermal power plant

    SciTech Connect (OSTI)

    Forte, N.

    1996-12-31

    The 125 MW Upper Mahiao power plant, the first geothermal power project to be financed under a Build-Own-Operate-and-Transfer (BOOT) arrangement in the Philippines, expected to complete its start-up testing in August of this year. This plant uses Ormat`s environmentally benign technology and is both the largest geothermal steam/binary combined cycle plant as well as the largest geothermal power plant utilizing air cooled condensers. The Ormat designed and constructed plant was developed under a fast track program, with some two years from the April 1994 contract signing through design, engineering, construction and startup. The plant is owned and operated by a subsidiary of CalEnergy Co., Inc. and supplies power to PNOC-Energy Development Corporation for the National Power Corporation (Napocor) national power grid in the Philippines.

  2. Semi-Implicit Reversible Algorithms for Rigid Body Rotational Dynamics

    SciTech Connect (OSTI)

    Nukala, Phani K; Shelton Jr, William Allison

    2006-09-01

    This paper presents two semi-implicit algorithms based on splitting methodology for rigid body rotational dynamics. The first algorithm is a variation of partitioned Runge-Kutta (PRK) methodology that can be formulated as a splitting method. The second algorithm is akin to a multiple time stepping scheme and is based on modified Crouch-Grossman (MCG) methodology, which can also be expressed as a splitting algorithm. These algorithms are second-order accurate and time-reversible; however, they are not Poisson integrators, i.e., non-symplectic. These algorithms conserve some of the first integrals of motion, but some others are not conserved; however, the fluctuations in these invariants are bounded over exponentially long time intervals. These algorithms exhibit excellent long-term behavior because of their reversibility property and their (approximate) Poisson structure preserving property. The numerical results indicate that the proposed algorithms exhibit superior performance compared to some of the currently well known algorithms such as the Simo-Wong algorithm, Newmark algorithm, discrete Moser-Veselov algorithm, Lewis-Simo algorithm, and the LIEMID[EA] algorithm.

  3. Highly conductive thermoplastic composites for rapid production of fuel cell bipolar plates

    DOE Patents [OSTI]

    Huang, Jianhua [Blacksburg, VA; Baird, Donald G [Blacksburg, VA; McGrath, James E [Blacksburg, VA

    2008-04-29

    A low cost method of fabricating bipolar plates for use in fuel cells utilizes a wet lay process for combining graphite particles, thermoplastic fibers, and reinforcing fibers to produce a plurality of formable sheets. The formable sheets are then molded into a bipolar plates with features impressed therein via the molding process. The bipolar plates formed by the process have conductivity in excess of 150 S/cm and have sufficient mechanical strength to be used in fuel cells. The bipolar plates can be formed as a skin/core laminate where a second polymer material is used on the skin surface which provides for enhanced conductivity, chemical resistance, and resistance to gas permeation.

  4. Light-Weight, Low-Cost, Single-Phase, Liquid-Cooled Cold Plate (Presentation)

    SciTech Connect (OSTI)

    Narumanchi, S.

    2013-07-01

    This presentation, 'Light-Weight, Low-Cost, Single-Phase Liquid-Cooled Cold Plate,' directly addresses program goals of increased power density, specific power, and lower cost of power electronics components through improved thermal management.

  5. Compact, Light-Weight, Single-Phase, Liquid-Cooled Cold Plate...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Peer Evaluation PDF icon ape039narumanchi2011p.pdf More Documents & Publications Compact, Light-Weight, Single-Phase, Liquid-Cooled Cold Plate Advanced Liquid Cooling R&D

  6. UPDATE ON FRICTION BONDING OF MONOLITHIC U-MO FUEL PLATES

    SciTech Connect (OSTI)

    D. E. Burkes; N. P. Hallinan; J. M. Wight; M. D. Chapple

    2007-09-01

    Friction Bonding (FB), formerly referred to as Friction Stir Welding, is an alternative plate fabrication technique to encapsulate monolithic U-Mo fuel foils inside 6061-T6 aluminum alloy cladding. Over the past year, significant progress has been made in the area of FB, including improvements in tool material, tool design, process parameters, cooling capability and capacity and modeling, all of which improve and enhance the quality of fabricated fuel plates, reproducibility of the fabrication process and bond quality of the fuel plates. Details of this progress and how it relates to the observed improvements and enhancements are discussed. In addition, details on how these improvements have been implemented into the last two RERTR mini-plate irradiation campaigns are also discussed.

  7. TESTING AND ACCEPTANCE OF FUEL PLATES FOR RERTR FUEL DEVELOPMENT EXPERIMENTS

    SciTech Connect (OSTI)

    J.M. Wight; G.A. Moore; S.C. Taylor

    2008-10-01

    This paper discusses how candidate fuel plates for RERTR Fuel Development experiments are examined and tested for acceptance prior to reactor insertion. These tests include destructive and nondestructive examinations (DE and NDE). The DE includes blister annealing for dispersion fuel plates, bend testing of adjacent cladding, and microscopic examination of archive fuel plates. The NDE includes Ultrasonic (UT) scanning and radiography. UT tests include an ultrasonic scan for areas of “debonds” and a high frequency ultrasonic scan to determine the "minimum cladding" over the fuel. Radiography inspections include identifying fuel outside of the maximum fuel zone and measurements and calculations for fuel density. Details of each test are provided and acceptance criteria are defined. These tests help to provide a high level of confidence the fuel plate will perform in the reactor without a breach in the cladding.

  8. ORNL characterization of Heavy-Section Steel Technology Program plates 01, 02, and 03

    SciTech Connect (OSTI)

    Stelzman, W.J.; Berggren, R.G.; Jones, T.N. Jr.

    1985-04-01

    Charpy V-notch impact, tensile, and drop-weight data are presented for three 305-mm-thick (12-in.) A 533 grade B class 1 steel plates. The effects of specimen size and orientation were examined as well as the variation of properties between different plate locations and depths. Some observations based on data obtained from an instrumented Charpy testing machine are also presented.

  9. Edge seal for a porous gas distribution plate of a fuel cell

    DOE Patents [OSTI]

    Feigenbaum, Haim; Pudick, Sheldon; Singh, Rajindar

    1984-01-01

    In an improved seal for a gas distribution plate of a fuel cell, a groove is provided extending along an edge of the plate. A member of resinous material is arranged within the groove and a paste comprising an immobilized acid is arranged surrounding the member and substantially filling the groove. The seal, which is impervious to the gas being distributed, is resistant to deterioration by the electrolyte of the cell.

  10. Nuclear reactor fuel structure containing uranium alloy wires embedded in a metallic matrix plate

    DOE Patents [OSTI]

    Travelli, A.

    1985-10-25

    A flat or curved plate structure, to be used as fuel in a nuclear reactor, comprises elongated fissionable wires or strips embedded in a metallic continuous non-fissionable matrix plate. The wires or strips are made predominantly of a malleable uranium alloy, such as uranium silicide, uranium gallide or uranium germanide. The matrix plate is made predominantly of aluminum or an aluminum alloy. The wires or strips are located in a single row at the midsurface of the plate, parallel with one another and with the length dimension of the plate. The wires or strips are separated from each other, and from the surface of the plate, by sufficient thicknesses of matrix material, to provide structural integrity and effective fission product retention, under neutron irradiation. This construction makes it safely feasible to provide a high uranium density, so that the uranium enrichment with uranium 235 may be reduced below about 20%, to deter the reprocessing of the uranium for use in nuclear weapons.

  11. Nuclear reactor fuel structure containing uranium alloy wires embedded in a metallic matrix plate

    DOE Patents [OSTI]

    Travelli, Armando

    1988-01-01

    A flat or curved plate structure, to be used as fuel in a nuclear reactor, comprises elongated fissionable wires or strips embedded in a metallic continuous non-fissionable matrix plate. The wires or strips are made predominantly of a malleable uranium alloy, such as uranium silicide, uranium gallide or uranium germanide. The matrix plate is made predominantly of aluminum or an aluminum alloy. The wires or strips are located in a single row at the midsurface of the plate, parallel with one another and with the length dimension of the plate. The wires or strips are separated from each other, and from the surface of the plate, by sufficient thicknesses of matrix material, to provide structural integrity and effective fission product retention, under neutron irradiation. This construction makes it safely feasible to provide a high uranium density, so that the uranium enrichment with uranium 235 may be reduced below about 20%, to deter the reprocessing of the uranium for use in nuclear weapons.

  12. Dual capacity compressor with reversible motor and controls arrangement therefor

    DOE Patents [OSTI]

    Sisk, Francis J.

    1980-12-02

    A hermetic reciprocating compressor such as may be used in heat pump applications is provided for dual capacity operation by providing the crankpin of the crankshaft with an eccentric ring rotatably mounted thereon, and with the end of the connecting rod opposite the piston encompassing the outer circumference of the eccentric ring, with means limiting the rotation of the eccentric ring upon the crankpin between one end point and an opposite angularly displaced end point to provide different values of eccentricity depending upon which end point the eccentric ring is rotated to upon the crankpin, and a reversible motor in the hermetic shell of the compressor for rotating the crankshaft, the motor operating in one direction effecting the angular displacement of the eccentric ring relative to the crankpin to the one end point, and in the opposite direction effecting the angular displacement of the eccentric ring relative to the crankpin to the opposite end point, this arrangement automatically giving different stroke lengths depending upon the direction of motor rotation. The mechanical structure of the arrangement may take various forms including at least one in which any impact of reversal is reduced by utilizing lubricant passages and chambers at the interface area of the crankpin and eccentric ring to provide a dashpot effect. In the main intended application of the arrangement according to the invention, that is, in a refrigerating or air conditioning system, it is desirable to insure a delay during reversal of the direction of compressor operation. A control arrangement is provided in which the control system controls the direction of motor operation in accordance with temperature conditions, the system including control means for effecting operation in a low capacity direction or alternatively in a high capacity direction in response to one set, and another set, respectively, of temperature conditions and with timer means delaying a restart of the compressor motor for at least a predetermined time in response to a condition of the control means operative to initiate a change in the operating direction of the compressor when it restarts.

  13. Reducing collective quantum state rotation errors with reversible dephasing

    SciTech Connect (OSTI)

    Cox, Kevin C.; Norcia, Matthew A.; Weiner, Joshua M.; Bohnet, Justin G.; Thompson, James K.

    2014-12-29

    We demonstrate that reversible dephasing via inhomogeneous broadening can greatly reduce collective quantum state rotation errors, and observe the suppression of rotation errors by more than 21?dB in the context of collective population measurements of the spin states of an ensemble of 2.110{sup 5} laser cooled and trapped {sup 87}Rb atoms. The large reduction in rotation noise enables direct resolution of spin state populations 13(1) dB below the fundamental quantum projection noise limit. Further, the spin state measurement projects the system into an entangled state with 9.5(5) dB of directly observed spectroscopic enhancement (squeezing) relative to the standard quantum limit, whereas no enhancement would have been obtained without the suppression of rotation errors.

  14. Nanofiltration/reverse osmosis for treatment of coproduced waters

    SciTech Connect (OSTI)

    Mondal, S.; Hsiao, C.L.; Wickramasinghe, S.R. [Colorado State University, Ft Collins, CO (United States)

    2008-07-15

    Current high oil and gas prices have lead to renewed interest in exploration of nonconventional energy sources such as coal bed methane, tar sand, and oil shale. However oil and gas production from these nonconventional sources has lead to the coproduction of large quantities of produced water. While produced water is a waste product from oil and gas exploration it is a very valuable natural resource in the arid Western United States. Thus treated produced water could be a valuable new source of water. Commercially available nanofiltration and low pressure reverse osmosis membranes have been used to treat three produced waters. The results obtained here indicate that the permeate could be put to beneficial uses such as crop and livestock watering. However minimizing membrane fouling will be essential for the development of a practical process. Field Emission Scanning Electron Microscopy imaging may be used to observe membrane fouling.

  15. Statistical Stability and Time-Reversal Imgaing in Random Media

    SciTech Connect (OSTI)

    Berryman, J; Borcea, L; Papanicolaou, G; Tsogka, C

    2002-02-05

    Localization of targets imbedded in a heterogeneous background medium is a common problem in seismic, ultrasonic, and electromagnetic imaging problems. The best imaging techniques make direct use of the eigenfunctions and eigenvalues of the array response matrix, as recent work on time-reversal acoustics has shown. Of the various imaging functionals studied, one that is representative of a preferred class is a time-domain generalization of MUSIC (MUltiple Signal Classification), which is a well-known linear subspace method normally applied only in the frequency domain. Since statistical stability is not characteristic of the frequency domain, a transform back to the time domain after first diagonalizing the array data in the frequency domain takes optimum advantage of both the time-domain stability and the frequency-domain orthogonality of the relevant eigenfunctions.

  16. Adiabatic model and design of a translating field reversed configuration

    SciTech Connect (OSTI)

    Intrator, T. P.; Siemon, R. E.; Sieck, P. E.

    2008-04-15

    We apply an adiabatic evolution model to predict the behavior of a field reversed configuration (FRC) during decompression and translation, as well as during boundary compression. Semi-empirical scaling laws, which were developed and benchmarked primarily for collisionless FRCs, are expected to remain valid even for the collisional regime of FRX-L experiment. We use this approach to outline the design implications for FRX-L, the high density translated FRC experiment at Los Alamos National Laboratory. A conical theta coil is used to accelerate the FRC to the largest practical velocity so it can enter a mirror bounded compression region, where it must be a suitable target for a magnetized target fusion (MTF) implosion. FRX-L provides the physics basis for the integrated MTF plasma compression experiment at the Shiva-Star pulsed power facility at Kirtland Air Force Research Laboratory, where the FRC will be compressed inside a flux conserving cylindrical shell.

  17. Magnetization reversal driven by a spin torque oscillator

    SciTech Connect (OSTI)

    Sbiaa, R.

    2014-09-01

    Magnetization reversal of a magnetic free layer under spin transfer torque (STT) effect from a magnetic hard layer with a fixed magnetization direction and an oscillating layer is investigated. By including STT from the oscillating layer with in-plane anisotropy and orthogonal polarizer, magnetization-time dependence of free layer is determined. The results show that the frequency and amplitude of oscillations can be varied by adjusting the current density and magnetic properties. For an optimal oscillation frequency (f{sub opt}), a reduction of the switching time (t{sub 0}) of the free layer is observed. Both f{sub opt} and t{sub 0} increase with the anisotropy field of the free layer.

  18. Preliminary potentiometric map and flow dynamic characteristics for the upper-basalt confined aquifer system

    SciTech Connect (OSTI)

    Spane, F.A. Jr.; Raymond, R.G.

    1993-09-01

    This report presents the first comprehensive Hanford Site-wide potentiometric map for the upper-basalt confined aquifer system (i.e., the upper Saddle Mountains Basalt). In constructing the potentiometric map, over forty on-site and off-site monitoring wells and boreholes were used. The potentiometric map developed for the upper-basalt confined aquifer is consistent with the areal head pattern indicated for the Mabton interbed, which is a deeper and more areally extensive confined aquifer underlying the Hanford Site. Salient features for the upper-basalt confined aquifer system potentiometric map are described.

  19. Upper limits on the total cosmic-ray luminosity of individual sources

    SciTech Connect (OSTI)

    Anjos, R.C.; De Souza, V.; Supanitsky, A.D. E-mail: vitor@ifsc.usp.br

    2014-07-01

    In this paper, upper limits on the total luminosity of ultra-high-energy cosmic-rays (UHECR) E>10{sup 18} eV) are determined for five individual sources. The upper limit on the integral flux of GeV--TeV gamma-rays is used to extract the upper limit on the total UHECR luminosity of individual sources. The correlation between upper limit on the integral GeV--TeV gamma-ray flux and upper limit on the UHECR luminosity is established through the cascading process that takes place during propagation of the cosmic rays in the background radiation fields, as explained in reference [1]. Twenty-eight sources measured by FERMI-LAT, VERITAS and MAGIC observatories have been studied. The measured upper limit on the GeV--TeV gamma-ray flux is restrictive enough to allow the calculation of an upper limit on the total UHECR cosmic-ray luminosity of five sources. The upper limit on the UHECR cosmic-ray luminosity of these sources is shown for several assumptions on the emission mechanism. For all studied sources an upper limit on the ultra-high-energy proton luminosity is also set.

  20. REVERSE RADIATIVE SHOCK LASER EXPERIMENTS RELEVANT TO ACCRETING STREAM-DISK

    Office of Scientific and Technical Information (OSTI)

    IMPACT IN INTERACTING BINARIES (Journal Article) | SciTech Connect REVERSE RADIATIVE SHOCK LASER EXPERIMENTS RELEVANT TO ACCRETING STREAM-DISK IMPACT IN INTERACTING BINARIES Citation Details In-Document Search Title: REVERSE RADIATIVE SHOCK LASER EXPERIMENTS RELEVANT TO ACCRETING STREAM-DISK IMPACT IN INTERACTING BINARIES We present the first results from high-energy-density laboratory astrophysics experiments that explore the hydrodynamic and radiative properties of a reverse shock relevant

  1. Advanced Materials for Reversible Solid Oxide Fuel Cell (RSOFC), Dual Mode

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Operation with Low Degradation | Department of Energy for Reversible Solid Oxide Fuel Cell (RSOFC), Dual Mode Operation with Low Degradation Advanced Materials for Reversible Solid Oxide Fuel Cell (RSOFC), Dual Mode Operation with Low Degradation Presented at the Department of Energy Fuel Cell Projects Kickoff Meeting, September 1 - October 1, 2009 PDF icon petri_versa%20_power_kickoff.pdf More Documents & Publications Reversible Fuel Cells Workshop Summary Report Progress on the

  2. Considerations for the use of the modified line reversal technique for gas temperature measurement

    SciTech Connect (OSTI)

    Winkleman, B.C.

    1993-06-01

    Several areas related to the successful and accurate application of modified line reversal are discussed. Initially, generalized modified line reversal equations are developed. A review of basic line reversal theory is presented followed by development of correction factors for optical system effects. Image size and their effect on accurate determinations of spectral radiances is discussed. Temperature biases introduced by image vignetting is calculated. Measured image irradiances are given.

  3. Strong and Reversible Binding of Carbon Dioxide in a Green Metal...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Strong and Reversible Binding of Carbon Dioxide in a Green Metal-Organic Framework Previous Next List Jeremiah J. Gassensmith, Hiroyasu Furukawa, Ronald A. Smaldone, Ross S....

  4. Testing the Time-Reversal Modified Universality of the Sivers Function

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect Testing the Time-Reversal Modified Universality of the Sivers Function Citation Details In-Document Search Title: Testing the Time-Reversal Modified Universality of the Sivers Function We derive the time-reversal modified universality for both quark and gluon Sivers functions from the parity and time-reversal invariance of QCD. We calculate the single transverse-spin asymmetry of inclusive lepton from the decay of W bosons in polarized proton-proton

  5. Magnetization reversal induced by in-plane current in Ta/CoFeB...

    Office of Scientific and Technical Information (OSTI)

    current are accordance with those for magnetization reversal by spin transfer torque originated from the spin Hall effect in the Ta layer. Authors: Zhang, C. 1 ;...

  6. Are We Heading Towards a Reversal of the Trend for Ever-Greater...

    Open Energy Info (EERE)

    Mobility? Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Are We Heading Towards a Reversal of the Trend for Ever-Greater Mobility? AgencyCompany Organization:...

  7. Nano-scale Composite Hetero-structures: Novel High Capacity Reversible...

    Broader source: Energy.gov (indexed) [DOE]

    Nano-scale Composite Hetero-structures: Novel High Capacity Reversible Anodes for Lithium-ion Batteries Nanoscale Heterostructures and Thermoplastic Resin Binders: Novel ...

  8. A simple technique to reduce evaporation of crystallization droplets by using plate lids with apertures for adding liquids

    SciTech Connect (OSTI)

    Zipper, Lauren E.; Aristide, Xavier; Bishop, Dylan P.; Joshi, Ishita; Kharzeev, Julia; Patel, Krishna B.; Santiago, Brianna M.; Joshi, Karan; Dorsinvil, Kahille; Sweet, Robert M.; Soares, Alexei S.

    2014-11-28

    This article describes the use of evaporation control lids that are fitted to crystallization plates to improve the reproducibility of trials using as little as 5 nl. The plate lids contain apertures which are large enough for the transfer of protein containing droplets, but small enough to greatly reduce the rate of evaporation during the time needed to prepare the plate. A method is described for using plate lids to reduce evaporation in low-volume vapor-diffusion crystallization experiments. The plate lids contain apertures through which the protein and precipitants were added to different crystallization microplates (the reservoir was filled before fitting the lids). Plate lids were designed for each of these commonly used crystallization microplates. This system minimizes the dehydration of crystallization droplets containing just a few nanolitres of protein and precipitant, and results in more reproducible diffraction from the crystals. For each lid design, changes in the weight of the plates were used to deduce the rate of evaporation under different conditions of temperature, air movement, droplet size and precipitant. For comparison, the state of dehydration was also visually assessed throughout the experiment. Finally, X-ray diffraction methods were used to compare the diffraction of protein crystals that were conventionally prepared against those that were prepared on plates with plate lids. The measurements revealed that the plate lids reduced the rate of evaporation by 6382%. Crystals grown in 5 nl drops that were set up with plate lids diffracted to higher resolution than similar crystals from drops that were set up without plate lids. The results demonstrate that plate lids can be instrumental for improving few-nanolitre crystallizations.

  9. Upper critical fields in liquid-quenched metastable superconductors

    SciTech Connect (OSTI)

    Wong, K.M.; Cotts, E.J.; Poon, S.J.

    1984-08-01

    A systematic and quantitative study of upper critical fields in alloys with increasing atomic number is carried out. The alloys are prepared by the technique of liquid (splat) quenching. They include the metastable body-centered-cubic (..beta..) phase of Ti-Pd, Zr-Mo, Zr-Pd, and Hf-Mo, amorphous phase of Zr-Rh, and the stable ..beta.. phase of Ti-Mo and Ta-Hf. Measurements are made in magnetic fields up to 90 kG and in temperatures down to 0.5 K. The results are analyzed within the framework of the dirty-limit theory of Werthamer, Helfand, Hohenberg, and Maki (WHHM). A least-squares fitting routine is performed using all the data (weighted equally) for a given sample. It is emphasized that the visual critical-field gradient near the transition temperature cannot be taken as the actual gradient in the presence of Pauli paramagnetic limitation. The main findings are the following: (i) Even without including renormalization corrections due to electron-phonon and electron-electron interactions, very good fits to the WHHM theory are obtained; (ii) critical-field data for all our samples (with minor exceptions in Hf-Mo)= are found to fall below or on the Maki curve (i.e., when the spin-orbit scattering parameter lambda/sub s.o./ goes to infinity); (iii) values of lambda/sub s.o./ are observed to range from 0.28 to 2.51 for the 3d and 4d alloys; (iv) the spin-orbit scattering rates 1/tau/sub s.o./ are found to compare well with theoretical estimation using results from band-structure calculation. The effect of sample inhomogeneity on the value of lambda/sub s.o./ in Zr-Mo alloys is also illustrated.

  10. UPPER BOUND ON THE FIRST STAR FORMATION HISTORY

    SciTech Connect (OSTI)

    Inoue, Yoshiyuki; Madejski, Grzegorz M.; Tanaka, Yasuyuki T.; Domnguez, Alberto

    2014-02-01

    Our understanding of the nature of the extragalactic background light (EBL) has improved with the recent development of gamma-ray observation techniques. An open subject in the context of the EBL is the reionization epoch, which is an important probe of the formation history of first stars, the so-called Population III (Pop III) stars. Although the mechanisms for the formation of PopIII stars are rather well understood on theoretical grounds, their formation history is still veiled in mystery because of their faintness. To shed light on this matter, we study jointly the gamma-ray opacity of distant objects and the reionization constraints from studies of intergalactic gas. By combining these studies, we obtain a sensitive upper bound on the PopIII star formation rate density of ?-dot {sub ?}(z)<0.01[(1+z)/(1+7.0)]{sup 3.4}(f{sub esc}/0.2){sup ?1}(C/3.0)M{sub ?}yr{sup ?1}Mpc{sup ?3} at z ? 7, where f {sub esc} and C are the escape fraction of ionizing photons from galaxies and the clumping factor of the intergalactic hydrogen gas. This limit is a ?10times tighter constraint compared with previous studies that take into account gamma-ray opacity constraints only. Even if we do not include the current gamma-ray constraints, the results do not change. This is because the detected gamma-ray sources are still at z ? 4.35 where the reionization has already finished.

  11. Evaluating Radiative Closure in the Middle-to-Upper Troposhere

    SciTech Connect (OSTI)

    Tobin, David C; Turner, David D; Knuteson, Robert O

    2013-01-02

    This project had two general objectives. The first is the characterization and improvement of the radiative transfer parameterization in strongly absorbing water vapor bands, as these strongly absorbing bands dictate the clear sky radiative heating rate. The second is the characterization and improvement of the radiative transfer in cirrus clouds, with emphasis on ensuring that the parameterization of the radiative transfer is consistent and accurate across the spectrum. Both of these objectives are important for understanding the radiative processes in the mid-to-upper troposphere. The research on this project primarily involved analysis of data from the First and Second Radiative Heating in Underexplored Bands Campaigns, RHUBC-I and II. This included a climate model sensitivity study using results from RHUBC-I. The RHUBC experiments are ARM-funded activities that directly address the objectives of this research project. A secondary effort was also conducted that investigated the trends in the long-term (~14 year) dataset collected by the Atmospheric Emitted Radiance Interferometer (AERI) at the ARM Southern Great Plains site. This work, which was primarily done by a post-doc at the University of Wisconsin – Madison under Dr. Turner’s direction, uses the only NIST-traceable instrument at the ARM site that has a well-documented calibration and uncertainty performance to investigate long-term trends in the downwelling longwave radiance above this site.

  12. MODIFIED REVERSE OSMOSIS SYSTEM FOR TREATMENT OF PRODUCED WATERS

    SciTech Connect (OSTI)

    T.M. Whitworth; Liangxiong Li

    2002-09-15

    This report describes work performed during the first year of the project ''Modified Reverse Osmosis System for Treatment of Produced Waters.'' This research project has two objectives. The first objective is to test the use of clay membranes in the treatment of produced waters by reverse osmosis. The second objective is to test the ability of a system patented by the New Mexico Tech Research Foundation to remove salts from reverse osmosis waste streams as a solid. We performed 12 experiments using clay membranes in cross-flow experimental cells. We found that, due to dispersion in the porous frit used adjacent to the membrane, the concentration polarization layer seems to be completely (or nearly completely) destroyed at low flow rates. This observation suggests that clay membranes used with porous frit material many reach optimum rejection rates at lower pumping rates than required for use with synthetic membranes. The solute rejection efficiency decreases with increasing solution concentration. For the membranes and experiments reported here, the rejection efficiency ranged from 71% with 0.01 M NaCl solution down to 12% with 2.3 M NaCl solution. More compacted clay membranes will have higher rejection capabilities. The clay membranes used in our experiments were relatively thick (approximately 0.5 mm). The active layer of most synthetic membranes is only 0.04 {micro}m (0.00004 mm), approximately 1250 times thinner than the clay membranes used in these experiments. Yet clay membranes as thin as 12 {micro}m have been constructed (Fritz and Eady, 1985). Since Darcy's law states that the flow through a material of constant permeability is inversely proportional to it's the material's thickness, then, based on these experimental observations, a very thin clay membrane would be expected to have much higher flow rates than the ones used in these experiments. Future experiments will focus on testing very thin clay membranes. The membranes generally exhibited reasonable stable rejection rates over time for chloride for a range of concentrations between 0.01 and 2.5 M. One membrane ran in excess of three months with no apparent loss of usability. This suggests that clay membranes may have a long useable life. Twenty different hyperfiltration-induced solute precipitation experiments were either attempted or completed and are reported here. The results of these experiments suggest that hyperfiltration-induced solute precipitation is possible, even for very soluble substances such as NaCl. However, the precipitation rates obtained in the laboratory do not appear to be adequate for commercial application at this time. Future experiments will focus on making the clay membranes more compact and thinner in order to obtain higher flux rates. Two alternative methods of removing solutes from solution, for which the New Mexico Tech Research Foundation is preparing patent applications, are also being investigated. These methods will be described in the next annual report after the patent applications are filed. Technology transfer efforts included two meetings (one in Farmington NM, and one in Hobbs, NM) where the results of this research were presented to independent oil producers and other interested parties. In addition, members of the research team gave seven presentations concerning this research and because of this research project T. M. (Mike) Whitworth was asked to sit on the advisory board for development of a new water treatment facility for the City of El Paso, Texas. Several papers are in preparation for submission to peer-reviewed journals based on the data presented in this report.

  13. Compact Reversed-Field Pinch Reactors (CRFPR): preliminary engineering considerations

    SciTech Connect (OSTI)

    Hagenson, R.L.; Krakowski, R.A.; Bathke, C.G.; Miller, R.L.; Embrechts, M.J.; Schnurr, N.M.; Battat, M.E.; LaBauve, R.J.; Davidson, J.W.

    1984-08-01

    The unique confinement physics of the Reversed-Field Pinch (RFP) projects to a compact, high-power-density fusion reactor that promises a significant reduction in the cost of electricity. The compact reactor also promises a factor-of-two reduction in the fraction of total cost devoted to the reactor plant equipment (i.e., fusion power core (FPC) plus support systems). In addition to operational and developmental benefits, these physically smaller systems can operate economically over a range of total power output. After giving an extended background and rationale for the compact fusion approaches, key FPC subsystems for the Compact RFP Reactor (CRFPR) are developed, designed, and integrated for a minimum-cost, 1000-MWe(net) system. Both the problems and promise of the compact, high-power-density fusion reactor are quantitatively evaluated on the basis of this conceptual design. The material presented in this report both forms a framework for a broader, more expanded conceptual design as well as suggests directions and emphases for related research and development.

  14. Reversible rigid coupling apparatus and method for borehole seismic transducers

    DOE Patents [OSTI]

    Owen, Thomas E.; Parra, Jorge O.

    1992-01-01

    An apparatus and method of high resolution reverse vertical seismic profile (VSP) measurements is shown. By encapsulating the seismic detector and heaters in a meltable substance (such as wax), the seismic detector can be removably secured in a borehole in a manner capable of measuring high resolution signals in the 100 to 1000 hertz range and higher. The meltable substance is selected to match the overall density of the detector package with the underground formation, yet still have relatively low melting point and rigid enough to transmit vibrations to accelerometers in the seismic detector. To minimize voids in the meltable substance upon solidification, the meltable substance is selected for minimum shrinkage, yet still having the other desirable characteristics. Heaters are arranged in the meltable substance in such a manner to allow the lowermost portion of the meltable substance to cool and solidify first. Solidification continues upwards from bottom-to-top until the top of the meltable substance is solidified and the seismic detector is ready for use. To remove, the heaters melt the meltable substance and the detector package is pulled from the borehole.

  15. Transport and equilibrium in field-reversed mirrors

    SciTech Connect (OSTI)

    Boyd, J.K.

    1982-09-01

    Two plasma models relevant to compact torus research have been developed to study transport and equilibrium in field reversed mirrors. In the first model for small Larmor radius and large collision frequency, the plasma is described as an adiabatic hydromagnetic fluid. In the second model for large Larmor radius and small collision frequency, a kinetic theory description has been developed. Various aspects of the two models have been studied in five computer codes ADB, AV, NEO, OHK, RES. The ADB code computes two dimensional equilibrium and one dimensional transport in a flux coordinate. The AV code calculates orbit average integrals in a harmonic oscillator potential. The NEO code follows particle trajectories in a Hill's vortex magnetic field to study stochasticity, invariants of the motion, and orbit average formulas. The OHK code displays analytic psi(r), B/sub Z/(r), phi(r), E/sub r/(r) formulas developed for the kinetic theory description. The RES code calculates resonance curves to consider overlap regions relevant to stochastic orbit behavior.

  16. Fusion proton diagnostic for the C-2 field reversed configuration

    SciTech Connect (OSTI)

    Magee, R. M. Clary, R.; Korepanov, S.; Smirnov, A.; Garate, E.; Knapp, K.; Tkachev, A.

    2014-11-15

    Measurements of the flux of fusion products from high temperature plasmas provide valuable insights into the ion energy distribution, as the fusion reaction rate is a very sensitive function of ion energy. In C-2, where field reversed configuration plasmas are formed by the collision of two compact toroids and partially sustained by high power neutral beam injection [M. Binderbauer et al., Phys. Rev. Lett. 105, 045003 (2010); M. Tuszewski et al., Phys. Rev. Lett. 108, 255008 (2012)], measurements of DD fusion neutron flux are used to diagnose ion temperature and study fast ion confinement and dynamics. In this paper, we will describe the development of a new 3 MeV proton detector that will complement existing neutron detectors. The detector is a large area (50?cm{sup 2}), partially depleted, ion implanted silicon diode operated in a pulse counting regime. While the scintillator-based neutron detectors allow for high time resolution measurements (?100 kHz), they have no spatial or energy resolution. The proton detector will provide 10 cm spatial resolution, allowing us to determine if the axial distribution of fast ions is consistent with classical fast ion theory or whether anomalous scattering mechanisms are active. We will describe in detail the diagnostic design and present initial data from a neutral beam test chamber.

  17. Two-dimensional interpreter for field-reversed configurations

    SciTech Connect (OSTI)

    Steinhauer, Loren

    2014-08-15

    An interpretive method is developed for extracting details of the fully two-dimensional (2D) “internal” structure of field-reversed configurations (FRC) from common diagnostics. The challenge is that only external and “gross” diagnostics are routinely available in FRC experiments. Inferring such critical quantities as the poloidal flux and the particle inventory has commonly relied on a theoretical construct based on a quasi-one-dimensional approximation. Such inferences sometimes differ markedly from the more accurate, fully 2D reconstructions of equilibria. An interpreter based on a fully 2D reconstruction is needed to enable realistic within-the-shot tracking of evolving equilibrium properties. Presented here is a flexible equilibrium reconstruction with which an extensive data base of equilibria was constructed. An automated interpreter then uses this data base as a look-up table to extract evolving properties. This tool is applied to data from the FRC facility at Tri Alpha Energy. It yields surprising results at several points, such as the inferences that the local β (plasma pressure/external magnetic pressure) of the plasma climbs well above unity and the poloidal flux loss time is somewhat longer than previously thought, both of which arise from full two-dimensionality of FRCs.

  18. Multichannel optical diagnostic system for field-reversed configuration plasmas

    SciTech Connect (OSTI)

    Takahashi, Tsutomu; Gota, Hiroshi; Fujino, Toshiyuki; Okada, Masanori; Asai, Tomohiko; Fujimoto, Kayoko; Ohkuma, Yasunori; Nogi, Yasuyuki

    2004-12-01

    A constructed diagnostic system consisting of a 60-channel set of optical detectors with flexible viewing configurations is realized to investigate three-dimensional magnetohydrodynamic (MHD) motions and the internal structure of a field-reversed configuration (FRC) plasma. The system can detect radiation from the plasma in the wavelength range of 420-820 nm. Optical filters are used to select the wavelength ranges required in the experiment. The sensitivities of all the optical detectors are calibrated using radiation from the FRC plasma at a quiescent phase. Radiation profiles measured by orthogonal viewing configuration of the detectors are shown at three toroidal cross sections. From these profiles, the time evolution of the three-dimensional MHD motion of the plasma is depicted. The radiation profile measured by a one-dimensional viewing configuration yields not only an electron density profile inside the separatrix but also the width of an edge-layer plasma. A bright halo around the edge-layer plasma is observed using a Balmer-{alpha} line filter. The orthogonal viewing configuration can also be used to analyze the internal structure of the FRC. The deviated position of the major axis is estimated from the comparison between the measured radiation profiles and the nonconcentric density profile based on the rigid rotor profile model.

  19. Advances in the numerical modeling of field-reversed configurations

    SciTech Connect (OSTI)

    Belova, Elena V.; Davidson, Ronald C.; Ji, Hantao; Yamada, Masaaki

    2006-05-15

    The field-reversed configuration (FRC) is a compact torus with little or no toroidal magnetic field. A theoretical understanding of the observed FRC equilibrium and stability properties presents significant challenges due to the high plasma beta, plasma flows, large ion gyroradius, and the stochasticity of the particle orbits. Advanced numerical simulations are generally required to describe and understand the detailed behavior of FRC plasmas. Results of such simulations are presented in this paper. It is shown that 3D nonlinear hybrid simulations using the HYM code [E. V. Belova et al., Phys. Plasmas 7, 4996 (2000)] reproduce all major experimentally observed stability properties of elongated (theta-pinch-formed) FRCs. Namely, the scaling of the growth rate of the n=1 tilt mode with the S*/E parameter (S* is the FRC kinetic parameter, E is elongation, and n is toroidal mode number), the nonlinear saturation of the tilt mode, ion toroidal spin-up, and the growth of the n=2 rotational mode have been demonstrated and studied in detail. The HYM code has also been used to study stability properties of FRCs formed by the counterhelicity spheromak merging method. A new stability regime has been found for FRCs with elongation E{approx}1, which requires a close-fitting conducting shell and energetic beam ion stabilization.

  20. Two-fluid physics and field-reversed configurations

    SciTech Connect (OSTI)

    Hakim, A.; Shumlak, U.

    2007-05-15

    In this paper, algorithms for the solution of two-fluid plasma equations are presented and applied to the study of field-reversed configurations (FRCs). The two-fluid model is more general than the often used magnetohydrodynamic (MHD) model. The model takes into account electron inertia, charge separation, and the full electromagnetic field equations, and it allows for separate electron and ion motion. The algorithm presented is the high-resolution wave propagation scheme. The wave propagation method is based on solutions to the Riemann problem at cell interfaces. Operator splitting is used to incorporate the Lorentz and electromagnetic source terms. The algorithms are benchmarked against the Geospace Environmental Modeling Reconnection Challenge problem. Equilibrium of FRC is studied. It is shown that starting from a MHD equilibrium produces a relaxed two-fluid equilibrium with strong flows at the FRC edges due to diamagnetic drift. The azimuthal electron flow causes lower-hybrid drift instabilities (LHDI), which can be captured if the ion gyroradius is well resolved. The LHDI is known to be a possible source of anomalous resistivity in many plasma configurations. LHDI simulations are performed in slab geometries and are compared to recent experimental results.

  1. Homopolar machine for reversible energy storage and transfer systems

    DOE Patents [OSTI]

    Stillwagon, Roy E.

    1978-01-01

    A homopolar machine designed to operate as a generator and motor in reversibly storing and transferring energy between the machine and a magnetic load coil for a thermo-nuclear reactor. The machine rotor comprises hollow thin-walled cylinders or sleeves which form the basis of the system by utilizing substantially all of the rotor mass as a conductor thus making it possible to transfer substantially all the rotor kinetic energy electrically to the load coil in a highly economical and efficient manner. The rotor is divided into multiple separate cylinders or sleeves of modular design, connected in series and arranged to rotate in opposite directions but maintain the supply of current in a single direction to the machine terminals. A stator concentrically disposed around the sleeves consists of a hollow cylinder having a number of excitation coils each located radially outward from the ends of adjacent sleeves. Current collected at an end of each sleeve by sleeve slip rings and brushes is transferred through terminals to the magnetic load coil. Thereafter, electrical energy returned from the coil then flows through the machine which causes the sleeves to motor up to the desired speed in preparation for repetition of the cycle. To eliminate drag on the rotor between current pulses, the brush rigging is designed to lift brushes from all slip rings in the machine.

  2. Homopolar machine for reversible energy storage and transfer systems

    DOE Patents [OSTI]

    Stillwagon, Roy E.

    1981-01-01

    A homopolar machine designed to operate as a generator and motor in reversibly storing and transferring energy between the machine and a magnetic load coil for a thermo-nuclear reactor. The machine rotor comprises hollow thin-walled cylinders or sleeves which form the basis of the system by utilizing substantially all of the rotor mass as a conductor thus making it possible to transfer substantially all the rotor kinetic energy electrically to the load coil in a highly economical and efficient manner. The rotor is divided into multiple separate cylinders or sleeves of modular design, connected in series and arranged to rotate in opposite directions but maintain the supply of current in a single direction to the machine terminals. A stator concentrically disposed around the sleeves consists of a hollow cylinder having a number of excitation coils each located radially outward from the ends of adjacent sleeves. Current collected at an end of each sleeve by sleeve slip rings and brushes is transferred through terminals to the magnetic load coil. Thereafter, electrical energy returned from the coil then flows through the machine which causes the sleeves to motor up to the desired speed in preparation for repetition of the cycle. To eliminate drag on the rotor between current pulses, the brush rigging is designed to lift brushes from all slip rings in the machine.

  3. Cavitation erosion of silver plated coating at different temperatures and pressures

    SciTech Connect (OSTI)

    Hattori, Shuji; Motoi, Yoshihiro; Kikuta, Kengo; Tomaru, Hiroshi

    2014-04-11

    Cavitation often occurs in inducer pumps used for space rockets. Silver plated coating on the inducer liner faces the damage of cavitation. Therefore, it is important to study about the cavitation erosion resistance for silver plated coating at several operating conditions in the inducer pumps. In this study, the cavitation erosion tests were carried for silver plated coating in deionized water and ethanol at several liquid temperatures (273K400K) and pressures (0.10MPa0.48MPa). The mass loss rate is evaluated in terms of thermodynamic parameter ? proposed by Brennen [9], suppression pressure pp{sub v} (p{sub v}: saturated vapor pressure) and acoustic impedance ?c (?: density and c: sound speed). Cavitation bubble behaviors depending on the thermodynamic effect and the liquid type were observed by high speed video camera. The mass loss rate is formulated by thermodynamic parameter ?, suppression pressure pp{sub v} and acoustic impedance ?c.

  4. A simplified model for heat transfer in heat exchangers and stack plates for thermoacoustic devices

    SciTech Connect (OSTI)

    Chen, Y.; Herman, C.

    1999-07-01

    A simplified model of heat transfer in heat exchangers and stack plates of thermoacoustic devices was developed. The model took advantage of previous results regarding the thermal behavior of the thermoacoustic core for investigations of the performance of heat exchangers attached to the core. Geometrical and operational parameters as well as thermophysical properties of the heat exchangers, the plate, and the working medium were organized into dimensionless groups that allowed to account for their impact on the performance of the heat exchangers. Numerical simulations with the model were carried out. Nonlinear temperature distributions and heat fluxes near the edge of the stack plate were observed. Effects of different parameters on the thermal performance of the heat exchangers were investigated.

  5. Laser-driven miniature flyer plates for shock initiation of secondary explosives

    SciTech Connect (OSTI)

    Paisley, D.L.

    1989-01-01

    Miniature flyer plates (<1-mm diameter X <5-micron thick) of aluminum and other materials are accelerated by a 10-ns pulsed Nd:YAG laser to velocities >5 km/s. Velocity profiles are recorded by velocity interferometry (VISAR) techniques and impact planarity by electronic streak photography. Techniques for improving energy coupling from laser to flyer plate will be discussed. Flyer plate performance parameters will be compared with material properties. The P/sup n/t criteria for shock initiation of explosives will be compared for various flyer materials, pressure, and pulse duration. Performance of secondary explosives (PETN, HNS, HMX, various PBX, others) will be reported. These data will detail the experimental effect of t (in P/sup n/t) approaching values of a few nanoseconds. 9 refs., 5 figs.

  6. SEM and TEM Characterization of As-Fabricated U-7Mo Disperson Fuel Plates

    SciTech Connect (OSTI)

    D. D. Keiser, Jr.; B. Yao; E. Perez; Y. H. Sohn

    2009-11-01

    The starting microstructure of a dispersion fuel plate can have a dramatic impact on the overall performance of the plate during irradiation. To improve the understanding of the as-fabricated microstructures of dispersion fuel plates, SEM and TEM analysis have been performed on RERTR-9A archive fuel plates, which went through an additional hot isostatic procsssing (HIP) step during fabrication. The fuel plates had depleted U-7Mo fuel particles dispersed in either Al-2Si or 4043 Al alloy matrix. For the characterized samples, it was observed that a large fraction of the ?-phase U-7Mo alloy particles had decomposed during fabrication, and in areas near the fuel/matrix interface where the transformation products were present significant fuel/matrix interaction had occurred. Relatively thin Si-rich interaction layers were also observed around the U-7Mo particles. In the thick interaction layers, (U)(Al,Si)3 and U6Mo4Al43 were identified, and in the thin interaction layers U(Al,Si)3, U3Si3Al2, U3Si5, and USi1.88-type phases were observed. The U3Si3Al2 phase contained some Mo. Based on the results of this work, exposure of dispersion fuel plates to relatively high temperatures during fabrication impacts the overall microstructure, particularly the nature of the interaction layers around the fuel particles. The time and temperature of fabrication should be carefully controlled in order to produce the most uniform Si-rich layers around the U-7Mo particles.

  7. Heat transfer and flow of an impinged plate with an elliptic jet

    SciTech Connect (OSTI)

    Matsuda, Shoichi; Yaga, Minoru; Oyakawa, Kenyu

    1999-07-01

    The time and spatial temperature profiles on a jet impingement plate were measured using an infrared radiometer with a two-dimensional array of Indium-Antimony (In Sb) sensors for various nozzle exit-to-plate spaces for when the jet being issued from an elliptic nozzle impinges on the target plate. The isotherms of infrared images as well as heat transfer coefficients were obtained by measurement data. The heat transfer coefficients were also measured by using thermocouples. In order to compare the isotherms and heat transfer contours with flow patterns, the flows on the plate were visualized by the oil-film method, and the velocity and the turbulence intensity were measured by a hot wire anemometer. The phenomena of axes switching which are caused by the differences in self-induced velocity in non-circular vortices and have been the typical behaviors of free jets were observed on the impingement plate. The distribution of the isotherm and iso-heat transfer coefficients for the center portion were shorted in the major direction with an increase of the space between nozzle exit and impingement plate and elongated in the minor direction. The isotherms from the infrared image corresponded closely to the distribution of iso-heat transfer coefficients by using thermocouples. The shapes of flow patterns also corresponded to both the shape of the isotherms and the iso-heat transfer contours. In the twice length of nozzle diameter downstream from nozzle exit, the oil film pattern was elongated in the major axis direction for the center portion, which corresponded to both the lower temperature and higher heat transfer coefficient.

  8. Multi-gap Resistive Plate Chambers as a Time-of-Flight System for the PHENIX Experiment

    SciTech Connect (OSTI)

    Velkovska, Julia

    2013-12-08

    In this project a Time-of-Flight detector based on multi-gap resistive plate chambers was built and installed for the PHENIX experiment at RHIC.

  9. Heat transfer and flow resistance of a shell and plate-type evaporator

    SciTech Connect (OSTI)

    Uehara, H.; Stuhltraeger, E.; Miyara, A.; Murakami, H.; Miyazaki, K.

    1997-05-01

    The performance test of a shell-and-plate-type evaporator designed for OTEC plants, geothermal power plants, and heat pump systems is reported. This evaporator contains 30 plates with a unit area of 0.813 m{sup 2}, coated with aluminum powder on the working fluid side. Freon 22 is used as working fluid. Results show an overall heat transfer coefficient of about 5,000 W/(m{sup 2}K) when the heating water velocity is 1M/s. The mean boiling heat transfer coefficient is compared with a precious correlation proposed by Nakaoka and Uehara (1988). The water-side pressure loss is also reported.

  10. Image plate characterization and absolute calibration to low kilo-electron-volt electrons

    SciTech Connect (OSTI)

    Busold, S.; Philipp, K.; Otten, A.; Roth, M.

    2014-11-15

    We report on the characterization of an image plate and its absolute calibration to electrons in the low keV energy range (130 keV). In our case, an Agfa MD4.0 without protection layer was used in combination with a Fuji FLA7000 scanner. The calibration data are compared to other published data and a consistent picture of the sensitivity of image plates to electrons is obtained, which suggests a validity of the obtained calibration up to 100 keV.

  11. New Zone Plate for Soft X-Ray Microscopy at 15-nm Spatial Resolution

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    New Zone Plate for Soft X-Ray Microscopy at 15-nm Spatial Resolution New Zone Plate for Soft X-Ray Microscopy at 15-nm Spatial Resolution Print Wednesday, 31 August 2005 00:00 Analytical tools that combine spatial resolution with elemental and chemical identification at the nanometer scale along with large penetration depth are indispensable for the life and physical sciences. The XM-1 soft x-ray microscope at the ALS produces images that not only reveal structures but can identify their

  12. Pre-treatment for molybdenum or molybdenum-rich alloy articles to be plated

    DOE Patents [OSTI]

    Wright, Ralph R.

    1980-01-01

    This invention is a method for etching a molybdenum or molybdenum-rich alloy surface to promote the formation of an adherent bond with a subsequently deposited metallic plating. In a typical application, the method is used as a pre-treatment for surfaces to be electrolessly plated with nickel. The pre-treatment comprises exposing the crystal boundaries of the surface by (a) anodizing the surface in acidic solution to form a continuous film of gray molybdenum oxide thereon and (b) removing the film.

  13. Method for preparing surfaces of metal composites having a brittle phase for plating. [Patent application

    DOE Patents [OSTI]

    Coates, C.W.; Wilson, T.J.

    1982-05-19

    The present invention is directed to a method for preparing surfaces of two-phase metal composites having relatively brittle and malleable components for plating with corrosion-resistant material. In practice of the present invention, the surfaces of the composite are etched to remove a major portion or fraction of the brittle component. The etched surface is then peened with particulates for breaking the brittle component from the surfaces and for spreading or smearing the malleable component over the surfaces. The peened surface is then chemically cleaned of residual traces of the brittle component to which the corrosion-resistant material may be plated thereon in an adherent manner.

  14. Comment on ''The velocity field due to an oscillating plate in an Oldroyd-B

    Office of Scientific and Technical Information (OSTI)

    fluid'' by C.C. Hopkins and J.R. de Bruyn [Can. J. Phys. 92, 533 (2014)] (Journal Article) | SciTech Connect Comment on ''The velocity field due to an oscillating plate in an Oldroyd-B fluid'' by C.C. Hopkins and J.R. de Bruyn [Can. J. Phys. 92, 533 (2014)] Citation Details In-Document Search This content will become publicly available on September 11, 2016 Title: Comment on ''The velocity field due to an oscillating plate in an Oldroyd-B fluid'' by C.C. Hopkins and J.R. de Bruyn [Can. J.

  15. Experimental techniques for subnanosecond resolution of laser-launched plates and impact studies

    SciTech Connect (OSTI)

    Paisley, D.L.; Warnes, R.H.; Stahl, D.B.

    1994-09-01

    Miniature laser-launched plates have applications in shock wave physics, studying dynamic properties of materials and can be used to generate experimental data in a manner similar to a laboratory gas gun for one-dimensional impact experiments. Laser-launched plates have the advantage of small size, low kinetic energy, and can be launched with ubiquitous laboratory lasers. Because of the small size and high accelerations (10{sup 7}--10{sup 10} g`s), improved temporal resolution and optical non-contact methods to collect data are required. Traditional mechanical in-situ gauges would significantly impair the data quality and do not have the required time response.

  16. Interferometry and high speed photography of laser-driven flyer plates

    SciTech Connect (OSTI)

    Paisley, D.L.; Montoya, N.I.; Stahl, D.B.; Garcia, I.A.

    1989-01-01

    Laser-driven thin (2-10-/mu/ thick) plates of aluminum and copper are accelerated to velocities /ge/5 km/s by a 1.06-/mu/ wavelength Nd:YAG 8-10 ns FWHM laser pulse at power densities 0.7-4.0 GW/cm/sup 2/. Accelerations /ge/10/sup 9/ km/s/sup 2/ have been achieved. The acceleration and velocity of these 0.4-1.0-mm-diameter plates are experimentally recorded by velocity interferometry (VISAR) and the planarity of impact by streak photography. 6 refs., 7 figs.

  17. Parallel-plate heat pipe apparatus having a shaped wick structure

    DOE Patents [OSTI]

    Rightley, Michael J.; Adkins, Douglas R.; Mulhall, James J.; Robino, Charles V.; Reece, Mark; Smith, Paul M.; Tigges, Chris P.

    2004-12-07

    A parallel-plate heat pipe is disclosed that utilizes a plurality of evaporator regions at locations where heat sources (e.g. semiconductor chips) are to be provided. A plurality of curvilinear capillary grooves are formed on one or both major inner surfaces of the heat pipe to provide an independent flow of a liquid working fluid to the evaporator regions to optimize heat removal from different-size heat sources and to mitigate the possibility of heat-source shadowing. The parallel-plate heat pipe has applications for heat removal from high-density microelectronics and laptop computers.

  18. Electric Dipole Moments in Radioactive Nuclei, Tests of Time Reversal Symmetry

    SciTech Connect (OSTI)

    Auerbach, N.

    2010-11-24

    The research of radioactive nuclei opens new possibilities to study fundamental symmetries, such as time reversal and reflection symmetry. Such nuclei often provide conditions to check in an optimal way certain symmetries and the violation of such symmetries. We will discuss the possibility of obtaining improved limits on violation of time reversal symmetry using pear shaped radioactive nuclei. An effective method to test time reversal invariance in the non-strange sector is to measure parity and time reversal violating (T-P-odd) electromagnetic moments, (such as the static electric dipole moment). Parity and time reversal violating components in the nuclear force may produce P-T-odd moments in nuclei which in turn induce such moments in atoms. We will discuss the possibility that in some reflection asymmetric, heavy nuclei (which are radioactive) these moments are enhanced by several orders of magnitude. Present and future experiments, which will test this idea, will be mentioned.

  19. Radiative reverse shock laser experiments relevant to accretion processes in cataclysmic variables

    SciTech Connect (OSTI)

    Krauland, C. M.; Drake, R. P.; Kuranz, C. C.; Sweeney, R.; Grosskopf, M.; Klein, S.; Gillespie, R.; Keiter, P. A.; Loupias, B.; Falize, E.

    2013-05-15

    We discuss the production of radiative reverse shocks in experiments at the Omega-60 laser facility. The ability of this high-intensity laser to impart large energy densities on micron-thin foils makes it feasible to create supersonic plasma flows. Obtaining a radiative reverse shock in the laboratory requires a sufficiently fast flow (∼100 km/s) of a material whose opacity is large enough to produce energetically significant emission from experimentally achievable shocked layers. The reverse shock forms in the flow once it is impeded. This paper presents the first radiographic data of normal incidence, reverse shockwaves. These experiments are primarily motivated by the contribution of radiative reverse shock waves to the evolving dynamics of the cataclysmic variable (CV) system in which they reside. We show similarity properties to suggest that the experimental production of radiative reserve shocks in the laboratory may be scalable to such astrophysical systems.

  20. Ductile Tearing of Thin Aluminum Plates Under Blast Loading. Predictions with Fully Coupled Models and Biaxial Material Response Characterization

    SciTech Connect (OSTI)

    Corona, Edmundo; Gullerud, Arne S.; Haulenbeek, Kimberly K.; Reu, Phillip L.

    2015-06-01

    The work presented in this report concerns the response and failure of thin 2024- T3 aluminum alloy circular plates to a blast load produced by the detonation of a nearby spherical charge. The plates were fully clamped around the circumference and the explosive charge was located centrally with respect to the plate. The principal objective was to conduct a numerical model validation study by comparing the results of predictions to experimental measurements of plate deformation and failure for charges with masses in the vicinity of the threshold between no tearing and tearing of the plates. Stereo digital image correlation data was acquired for all tests to measure the deflection and strains in the plates. The size of the virtual strain gage in the measurements, however, was relatively large, so the strain measurements have to be interpreted accordingly as lower bounds of the actual strains in the plate and of the severity of the strain gradients. A fully coupled interaction model between the blast and the deflection of the structure was considered. The results of the validation exercise indicated that the model predicted the deflection of the plates reasonably accurately as well as the distribution of strain on the plate. The estimation of the threshold charge based on a critical value of equivalent plastic strain measured in a bulge test, however, was not accurate. This in spite of efforts to determine the failure strain of the aluminum sheet under biaxial stress conditions. Further work is needed to be able to predict plate tearing with some degree of confidence. Given the current technology, at least one test under the actual blast conditions where the plate tears is needed to calibrate the value of equivalent plastic strain when failure occurs in the numerical model. Once that has been determined, the question of the explosive mass value at the threshold could be addressed with more confidence.

  1. Flying-plate detonator using a high-density high explosive

    DOE Patents [OSTI]

    Stroud, John R.; Ornellas, Donald L.

    1988-01-01

    A flying-plate detonator containing a high-density high explosive such as benzotrifuroxan (BTF). The detonator involves the electrical explosion of a thin metal foil which punches out a flyer from a layer overlying the foil, and the flyer striking a high-density explosive pellet of BTF, which is more thermally stable than the conventional detonator using pentaerythritol tetranitrate (PETN).

  2. Finite element analysis of an extended end-plate connection using the T-stub approach

    SciTech Connect (OSTI)

    Muresan, Ioana Cristina; Balc, Roxana

    2015-03-10

    Beam-to-column end-plate bolted connections are usually used as moment-resistant connections in steel framed structures. For this joint type, the deformability is governed by the deformation capacity of the column flange and end-plate under tension and elongation of the bolts. All these elements around the beam tension flange form the tension region of the joint, which can be modeled by means of equivalent T-stubs. In this paper a beam-to-column end-plate bolted connection is substituted with a T-stub of appropriate effective length and it is analyzed using the commercially available finite element software ABAQUS. The performance of the model is validated by comparing the behavior of the T-stub from the numerical simulation with the behavior of the connection as a whole. The moment-rotation curve of the T-stub obtained from the numerical simulation is compared with the behavior of the whole extended end-plate connection, obtained by numerical simulation, experimental tests and analytical approach.

  3. Internal (Annular) and Compressible External (Flat Plate) Turbulent Flow Heat Transfer Correlations.

    SciTech Connect (OSTI)

    Dechant, Lawrence; Smith, Justin

    2016-01-01

    Here we provide a discussion regarding the applicability of a family of traditional heat transfer correlation based models for several (unit level) heat transfer problems associated with flight heat transfer estimates and internal flow heat transfer associated with an experimental simulation design (Dobranich 2014). Variability between semi-empirical free-flight models suggests relative differences for heat transfer coefficients on the order of 10%, while the internal annular flow behavior is larger with differences on the order of 20%. We emphasize that these expressions are strictly valid only for the geometries they have been derived for e.g. the fully developed annular flow or simple external flow problems. Though, the application of flat plate skin friction estimate to cylindrical bodies is a traditional procedure to estimate skin friction and heat transfer, an over-prediction bias is often observed using these approximations for missile type bodies. As a correction for this over-estimate trend, we discuss a simple scaling reduction factor for flat plate turbulent skin friction and heat transfer solutions (correlations) applied to blunt bodies of revolution at zero angle of attack. The method estimates the ratio between axisymmetric and 2-d stagnation point heat transfer skin friction and Stanton number solution expressions for sub-turbulent Reynolds numbers %3C1x10 4 . This factor is assumed to also directly influence the flat plate results applied to the cylindrical portion of the flow and the flat plate correlations are modified by

  4. Compact, Light-Weight, Single-Phase, Liquid-Cooled Cold Plate | Department

    Broader source: Energy.gov (indexed) [DOE]

    of Energy 2 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting PDF icon ape039_narumanchi_2012_o.pdf More Documents & Publications Advanced Liquid Cooling R&D Compact, Light-Weight, Single-Phase, Liquid-Cooled Cold Plate

  5. Compact, Light-Weight, Single-Phase, Liquid-Cooled Cold Plate | Department

    Broader source: Energy.gov (indexed) [DOE]

    of Energy ape039_narumanchi_2011_p.pdf More Documents & Publications Compact, Light-Weight, Single-Phase, Liquid-Cooled Cold Plate Advanced Liquid Cooling R&D Air Cooling Technology for Power Electronic Thermal Control

  6. Experimental Evaluation of Beam to Diamond Box Column Connection with Through Plate in Moment Frames

    SciTech Connect (OSTI)

    Keshavarzi, Farhad; Torabian, Shahabeddin; Imanpour, Ali; Mirghaderi, Rasoul

    2008-07-08

    Moment resisting frames with built up section have very enhanced features due to high bending stiffness and strength characteristics in two principal axes and access to column faces for beam to column easy connections. But due to proper transfer of beam stresses to column faces there were always some specific controvertibly issues that how to make the load transfer through and in plane manner in order to mobilize the forces in column faces. Using diamond column instead of box column provide possibility to mobilize the load transfer mechanism in column faces. This section as a column has considerable benefit such as high plastic to elastic section modulus ratio which is an effective factor for force controlled components. Typical connection has no chance to be applied with diamond column.This paper elucidates the seismic behavior of through-plates moment connections to diamond box columns for use in steel moment resisting frames. This connection has a lot of economical benefits such as no need to horizontal continuity plates and satisfying the weak beam--strong column criteria in the connection region. They might serve as panel zone plates as well. According to high shear demand in panel zone of beam to column joint one should use the doublers plates in order to decrease the shear strength demand in this sensitive part of structure but these plates have no possibility to mobilize the load transfer mechanism in column web and transfer them to column flanges. In this type of connection, column faces have effective role in order to decrease the demands on through plate and they are impressive factors for improving the performance of the connection.Experimental analysis was conducted to elucidate the seismic behavior of this connection. The results of Experimental analysis established the effectiveness of the through plate in mitigating local stress concentrations and forming the plastic hinge zone in the beam away from the beam to column interface. The moment-rotation graphs form sub-assemblage show a desirable seismic performance of this connection.

  7. Phenomenology of reverse-shock emission in the optical afterglows of gamma-ray bursts

    SciTech Connect (OSTI)

    Japelj, J.; Kopa?, D.; Gomboc, A. [Faculty of Mathematics and Physics, University of Ljubljana, Jadranska ulica 19, SI-1000 Ljubljana (Slovenia); Kobayashi, S.; Harrison, R.; Virgili, F. J.; Mundell, C. G. [Astrophysics Research Institute, Liverpool John Moores University, Liverpool, L3 5RF (United Kingdom); Guidorzi, C. [Physics Departments, University of Ferrara, via Saragat 1, I-44122, Ferrara (Italy); Melandri, A., E-mail: jure.japelj@fmf.uni-lj.si, E-mail: andreja.gomboc@fmf.uni-lj.si [INAF Osservatorio Astronomico di Brera, via E. Bianchi 46, I-23807 Merate (Italy)

    2014-04-20

    We use a parent sample of 118 gamma-ray burst (GRB) afterglows, with known redshift and host galaxy extinction, to separate afterglows with and without signatures of dominant reverse-shock (RS) emission and to determine which physical conditions lead to a prominent reverse-shock emission. We identify 10 GRBs with reverse-shock signatures: 990123, 021004, 021211, 060908, 061126, 080319B, 081007, 090102, 090424, and 130427A. By modeling their optical afterglows with reverse- and forward-shock analytic light curves and using Monte Carlo simulations, we estimate the parameter space of the physical quantities describing the ejecta and circumburst medium. We find that physical properties cover a wide parameter space and do not seem to cluster around any preferential values. Comparing the rest-frame optical, X-ray, and high-energy properties of the larger sample of non-RS-dominated GRBs, we show that the early-time (<1 ks) optical spectral luminosity, X-ray afterglow luminosity, and ?-ray energy output of our reverse-shock dominated sample do not differ significantly from the general population at early times. However, the GRBs with dominant reverse-shock emission have fainter than average optical forward-shock emission at late times (>10 ks). We find that GRBs with an identifiable reverse-shock component show a high magnetization parameter R {sub B} = ?{sub B,r}/?{sub B,f} ? 2-10{sup 4}. Our results are in agreement with the mildly magnetized baryonic jet model of GRBs.

  8. Upper Missouri G&T El Coop Inc | Open Energy Information

    Open Energy Info (EERE)

    G&T El Coop Inc Jump to: navigation, search Name: Upper Missouri G&T El Coop Inc Place: Montana Phone Number: 406-433-4100 Website: uppermo.com Outage Hotline: 406-433-4100...

  9. Upper limit power for self-guided propagation of intense lasers in plasma

    SciTech Connect (OSTI)

    Wang Weimin; Hu Zhidan; Chen Liming; Li Yutong; Sheng Zhengming; Zhang Jie; Zeng Ming; Liu Yue; Kawata, Shigeo; Zheng Chunyang; Mori, Warren B.

    2012-10-29

    It is shown that there is an upper-limit laser power for self-focusing of a laser pulse in plasma in addition to the well-known lower-limit critical power set by the relativistic effect. This upper limit is caused by the transverse ponderomotive force of the laser, which tends to expel plasma electrons from the laser propagating area. Furthermore, there is a lower-limit plasma density for a given laser spot size, below which self-focusing does not occur for any laser power. Both the lower-limit density and the upper-limit power are derived theoretically and verified by two-dimensional and three-dimensional particle-in-cell simulations. It is also found that plasma channels may be unfavorable for stable guiding of lasers above the upper-limit power.

  10. Observations Derived From the Characterization of Monolithic Fuel Plates Irradiated as Part of the RERTR-6 Experiment

    SciTech Connect (OSTI)

    D. D. Keiser, Jr.; A. B. Robinson; M. R. Finlay

    2007-09-01

    Evaluation of the PIE results of the monolithic plates that were irradiated as part of the RERTR-6 experiment has continued. Specifically, comparisons have been made between the microstructures of the fuel plates before and after irradiation. Using the results from the rigorous characterization that was performed on the as-fabricated plates using scanning electron microscopy, it is possible to improve understanding of how monolithic fuel plates perform when they are irradiated. This paper will discuss the changes that occur, if any, in the microstructure of a monolithic fuel plate that is fabricated using techniques like what were employed for fabricating RERTR-6 fuel plates. In addition, the performance of fuel/cladding interaction layers that were present in the fuel plates due to the fabrication process will be discussed, particularly in the context of swelling of these layers and how these layers exhibit different behaviors depending on whether the fuel alloy in the fuel plate is U-7Mo or U-10Mo.

  11. Microstructural Characterization of Burnable Absorber Materials Being Evaluated for Application in LEU U-Mo Fuel Plates

    SciTech Connect (OSTI)

    J. F. Jue; B. Miller; B. Yao; E. Perez; Y. H. Sohn

    2011-03-01

    The starting microstructure of a fuel plate will impact how it performs during irradiation. As a result, microstructural characterization has been performed on as-fabricated monolithic fuel plates to determine the changes in fuel plate microstructure that may result from changes in fabrication parameters. Particular focus has been given to the fuel plate U-10Mo/Zr and Zr/AA6061 cladding interfaces, since the integrity of these interfaces will play a big role in determining the overall performance of the fuel plate during irradiation. In addition, burnable absorber materials for potential incorporation into monolithic fuel plates have been characterized to identify their as-fabricated microstructures. This information will be important when trying to understand the PIE data from fuel plates with burnable absorbers that are irradiated in future irradiation experiments. This paper will focus on the microstructures observed using optical metallography, X-ray diffraction, and scanning and transmission electron microscopy for monolithic fuel plates exposed to different fabrication parameters and for as-fabricated burnable absorber materials.

  12. Upper Bound on the First Star Formation History (Journal Article) | SciTech

    Office of Scientific and Technical Information (OSTI)

    Connect Upper Bound on the First Star Formation History Citation Details In-Document Search Title: Upper Bound on the First Star Formation History Authors: Inoue, Yoshiyuki Publication Date: 2014-11-20 OSTI Identifier: 1165908 Report Number(s): SLAC-PUB-16151 Journal ID: ISSN 2041-8205 DOE Contract Number: AC02-76SF00515 Resource Type: Journal Article Resource Relation: Journal Name: Astrophysical Journal Letters; Journal Volume: 781; Journal Issue: 2 Publisher: Institute of Physics (IOP)

  13. Upper bounds on sparticle masses from naturalness or how to disprove weak

    Office of Scientific and Technical Information (OSTI)

    scale supersymmetry (Journal Article) | SciTech Connect Upper bounds on sparticle masses from naturalness or how to disprove weak scale supersymmetry Citation Details In-Document Search This content will become publicly available on February 15, 2017 Title: Upper bounds on sparticle masses from naturalness or how to disprove weak scale supersymmetry Authors: Baer, Howard ; Barger, Vernon ; Savoy, Michael Publication Date: 2016-02-16 OSTI Identifier: 1238092 Type: Publisher's Accepted

  14. LATE SPECTRAL EVOLUTION OF THE EJECTA AND REVERSE SHOCK IN SN 1987A

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect LATE SPECTRAL EVOLUTION OF THE EJECTA AND REVERSE SHOCK IN SN 1987A Citation Details In-Document Search Title: LATE SPECTRAL EVOLUTION OF THE EJECTA AND REVERSE SHOCK IN SN 1987A We present observations with the Very Large Telescope and Hubble Space Telescope (HST) of the broad emission lines from the inner ejecta and reverse shock of SN 1987A from 1999 February until 2012 January (days 4381-9100 after explosion). We detect broad lines from H{alpha},

  15. A new reversal mode in exchange coupled antiferromagnetic/ferromagnetic disks: distorted viscous vortex

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Gilbert, Dustin A.; Ye, Li; Varea, Aïda; Agramunt-Puig, Sebastià; del Valle, Nuria; Navau, Carles; López-Barbera, José Francisco; Buchanan, Kristen S.; Hoffmann, Axel; Sánchez, Alvar; et al

    2015-04-28

    Magnetic vortices have generated intense interest in recent years due to their unique reversal mechanisms, fascinating topological properties, and exciting potential applications. In addition, the exchange coupling of magnetic vortices to antiferromagnets has also been shown to lead to a range of novel phenomena and functionalities. Here we report a new magnetization reversal mode of magnetic vortices in exchange coupled Ir20Mn80/Fe20Ni80 microdots: distorted viscous vortex reversal. In contrast to the previously known or proposed reversal modes, the vortex is distorted close to the interface and viscously dragged due to the uncompensated spins of a thin antiferromagnet, which leads to unexpectedmore » asymmetries in the annihilation and nucleation fields. These results provide a deeper understanding of the physics of exchange coupled vortices and may also have important implications for applications involving exchange coupled nanostructures.« less

  16. A new reversal mode in exchange coupled antiferromagnetic/ferromagnetic disks: distorted viscous vortex

    SciTech Connect (OSTI)

    Gilbert, Dustin A.; Ye, Li; Varea, Aïda; Agramunt-Puig, Sebastià; del Valle, Nuria; Navau, Carles; López-Barbera, José Francisco; Buchanan, Kristen S.; Hoffmann, Axel; Sánchez, Alvar; Sort, Jordi; Liu, Kai; Nogués, Josep

    2015-04-28

    Magnetic vortices have generated intense interest in recent years due to their unique reversal mechanisms, fascinating topological properties, and exciting potential applications. In addition, the exchange coupling of magnetic vortices to antiferromagnets has also been shown to lead to a range of novel phenomena and functionalities. Here we report a new magnetization reversal mode of magnetic vortices in exchange coupled Ir20Mn80/Fe20Ni80 microdots: distorted viscous vortex reversal. In contrast to the previously known or proposed reversal modes, the vortex is distorted close to the interface and viscously dragged due to the uncompensated spins of a thin antiferromagnet, which leads to unexpected asymmetries in the annihilation and nucleation fields. These results provide a deeper understanding of the physics of exchange coupled vortices and may also have important implications for applications involving exchange coupled nanostructures.

  17. Colorado - C.R.S. 36-1-136 - Rights of Way Granted - Reversion...

    Open Energy Info (EERE)

    search OpenEI Reference LibraryAdd to library Legal Document- StatuteStatute: Colorado - C.R.S. 36-1-136 - Rights of Way Granted - ReversionLegal Abstract This section covers the...

  18. Proceedings of the Flat-Plate Solar Array Project Research Forum on the design of flat-plate photovoltaic arrays for central stations

    SciTech Connect (OSTI)

    1983-01-01

    The Flat-Plate Solar Array Project, managed by the Jet Propulsion Laboratory for the US Department of Energy, has focused on advancing technologies relevant to the design and construction of megawatt-level central-station systems. Photovoltaic modules and arrays for flat-plate central-station or other large-scale electric power production facilities require the establishment of a technical base that resolves design issues and results in practical and cost-effective configurations. The Central Station Research Forum addressed design, qualification and maintenance issues related to central-station arrays derived from the engineering and operating experiences of early applications and parallel laboratory research activities. Technical issues were examined from the viewpoint of the utility engineer, architect-engineer and laboratory researcher. The forum included presentations on optimum source-circuit designs, module insulation design for high system voltages, array safety, structural interface design, measurements and array operation and maintenance. The Research Forum focused on current capabilities as well as design difficulties requiring additional technological thrusts and/or continued research emphasis. Session topic summaries highlighting major points during group discussions, identifying promising technical approaches or areas of future research, are presented.

  19. Strain-assisted current-induced magnetization reversal in magnetic tunnel

    Office of Scientific and Technical Information (OSTI)

    junctions: A micromagnetic study with phase-field microelasticity (Journal Article) | SciTech Connect Strain-assisted current-induced magnetization reversal in magnetic tunnel junctions: A micromagnetic study with phase-field microelasticity Citation Details In-Document Search Title: Strain-assisted current-induced magnetization reversal in magnetic tunnel junctions: A micromagnetic study with phase-field microelasticity Effect of substrate misfit strain on current-induced in-plane

  20. FLUX ENHANCEMENT IN CROSSFLOW MEMBRANE FILTRATION: FOULING AND IT'S MINIMIZATION BY FLOW REVERSAL

    SciTech Connect (OSTI)

    Shamsuddin Ilias

    2005-01-25

    Fouling problems are perhaps the single most important reason for relatively slow acceptance of ultrafiltration in many areas of chemical and biological processing. To overcome the losses in permeate flux associated with concentration polarization and fouling in cross flow membrane filtration, we investigated the concept of flow reversal as a method to enhance membrane flux in ultrafiltration. Conceptually, flow reversal prevents the formation of stable hydrodynamic and concentration boundary layers at or near the membrane surface. Further more, periodic reversal of the flow direction of the feed stream at the membrane surface results in prevention and mitigation of membrane fouling. Consequently, these advantages are expected to enhance membrane flux significantly. A crossflow membrane filtration unit was designed and built to test the concept of periodic flow reversal for flux enhancement. The essential elements of the system include a crossflow hollow fiber membrane module integrated with a two-way valve to direct the feed flow directions. The two-way valve is controlled by a controller-timer for periodic reversal of flow of feed stream. Another important feature of the system is that with changing feed flow direction, the permeate flow direction is also changed to maintain countercurrent feed and permeate flows for enhanced mass transfer driving force (concentration difference). In this report, we report our application of Flow Reversal technique in clarification of apple juice containing pectin. The presence of pectin in apple juice makes the clarification process difficult and is believed to cause membrane fouling. Of all compounds found in apple juice, pectin is most often identified as the major hindrance to filtration performance. Based on our ultrafiltration experiments with apple juice, we conclude that under flow reversal conditions, the permeate flux is significantly enhanced when compared with the conventional unidirectional flow. Thus, flow reversal technology seems an attractive alternative to mitigate fouling problem in crossflow membrane filtration.

  1. Pairing state with a time-reversal symmetry breaking in FeAs-based

    Office of Scientific and Technical Information (OSTI)

    superconductors (Technical Report) | SciTech Connect Technical Report: Pairing state with a time-reversal symmetry breaking in FeAs-based superconductors Citation Details In-Document Search Title: Pairing state with a time-reversal symmetry breaking in FeAs-based superconductors We investigate the competition between the extended s{+-} wave and dx2-y2 -wave pairing order parameters in the iron-based superconductors. Because of the frustrating pairing interactions among the electron and the

  2. Real-time sub- Å ngstrom imaging of reversible and irreversible

    Office of Scientific and Technical Information (OSTI)

    conformations in rhodium catalysts and graphene (Journal Article) | DOE PAGES Real-time sub- Å ngstrom imaging of reversible and irreversible conformations in rhodium catalysts and graphene Title: Real-time sub- Å ngstrom imaging of reversible and irreversible conformations in rhodium catalysts and graphene Authors: Kisielowski, Christian ; Wang, Lin-Wang ; Specht, Petra ; Calderon, Hector A. ; Barton, Bastian ; Jiang, Bin ; Kang, Joo H. ; Cieslinski, Robert Publication Date: 2013-07-29

  3. Fullrmc, A Rigid Body Reverse Monte Carlo Modeling Package Enabled With

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Machine Learning And Artificial Intelligence - Joint Center for Energy Storage Research January 22, 2016, Research Highlights Fullrmc, A Rigid Body Reverse Monte Carlo Modeling Package Enabled With Machine Learning And Artificial Intelligence Liquid Sulfur. Sx≤8 molecules recognized and built upon modelling Scientific Achievement Novel approach to reverse modelling atomic and molecular systems from a set of experimental data and constraints. New fitting concepts such as 'Group',

  4. Probability of Future Observations Exceeding One-Sided, Normal, Upper Tolerance Limits

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Edwards, Timothy S.

    2014-10-29

    Normal tolerance limits are frequently used in dynamic environments specifications of aerospace systems as a method to account for aleatory variability in the environments. Upper tolerance limits, when used in this way, are computed from records of the environment and used to enforce conservatism in the specification by describing upper extreme values the environment may take in the future. Components and systems are designed to withstand these extreme loads to ensure they do not fail under normal use conditions. The degree of conservatism in the upper tolerance limits is controlled by specifying the coverage and confidence level (usually written inmore » “coverage/confidence” form). Moreover, in high-consequence systems it is common to specify tolerance limits at 95% or 99% coverage and confidence at the 50% or 90% level. Despite the ubiquity of upper tolerance limits in the aerospace community, analysts and decision-makers frequently misinterpret their meaning. The misinterpretation extends into the standards that govern much of the acceptance and qualification of commercial and government aerospace systems. As a result, the risk of a future observation of the environment exceeding the upper tolerance limit is sometimes significantly underestimated by decision makers. This note explains the meaning of upper tolerance limits and a related measure, the upper prediction limit. So, the objective of this work is to clarify the probability of exceeding these limits in flight so that decision-makers can better understand the risk associated with exceeding design and test levels during flight and balance the cost of design and development with that of mission failure.« less

  5. Boattail Plates With Non-Rectangular Geometries For Reducing Aerodynamic Base Drag Of A Bluff Body In Ground Effect

    DOE Patents [OSTI]

    Ortega, Jason M.; Sabari, Kambiz

    2006-03-07

    An apparatus for reducing the aerodynamic base drag of a bluff body having a leading end, a trailing end, a top surface, opposing left and right side surfaces, and a base surface at the trailing end substantially normal to a longitudinal centerline of the bluff body, with the base surface joined (1) to the left side surface at a left trailing edge, (2) to the right side surface at a right trailing edge, and (3) to the top surface at a top trailing edge. The apparatus includes left and right vertical boattail plates which are orthogonally attached to the base surface of the bluff body and inwardly offset from the left and right trailing edges, respectively. This produces left and right vertical channels which generate, in a flowstream substantially parallel to the longitudinal centerline, respective left and right vertically-aligned vortical structures, with the left and right vertical boattail plates each having a plate width defined by a rear edge of the plate spaced from the base surface. Each plate also has a peak plate width at a location between top and bottom ends of the plate corresponding to a peak vortex of the respective vertically-aligned vortical structures.

  6. Control design and robustness analysis of a ball and plate system by using polynomial chaos

    SciTech Connect (OSTI)

    Coln, Diego; Balthazar, Jos M.; Reis, Clia A. dos; Bueno, tila M.; Diniz, Ivando S.; Rosa, Suelia de S. R. F.

    2014-12-10

    In this paper, we present a mathematical model of a ball and plate system, a control law and analyze its robustness properties by using the polynomial chaos method. The ball rolls without slipping. There is an auxiliary robot vision system that determines the bodies' positions and velocities, and is used for control purposes. The actuators are to orthogonal DC motors, that changes the plate's angles with the ground. The model is a extension of the ball and beam system and is highly nonlinear. The system is decoupled in two independent equations for coordinates x and y. Finally, the resulting nonlinear closed loop systems are analyzed by the polynomial chaos methodology, which considers that some system parameters are random variables, and generates statistical data that can be used in the robustness analysis.

  7. Acoustic wave device using plate modes with surface-parallel displacement

    DOE Patents [OSTI]

    Martin, S.J.; Ricco, A.J.

    1988-04-29

    Solid-state acoustic sensors for monitoring conditions at a surface immersed in a liquid and for monitoring concentrations of species in a liquid and for monitoring electrical properties of a liquid are formed by placing interdigital input and output transducers on a piezoelectric substrate and propagating acoustic plate modes therebetween. The deposition or removal of material on or from, respectively, a thin film in contact with the surface, or changes in the mechanical properties of a thin film in contact with the surface, or changes in the electrical characteristics of the solution, create perturbations in the velocity and attenuation of the acoustic plate modes as a function of these properties or changes in them. 6 figs.

  8. Method and apparatus for acoustic plate mode liquid-solid phase transition detection

    DOE Patents [OSTI]

    Blair, Dianna S.; Freye, Gregory C.; Hughes, Robert C.; Martin, Stephen J.; Ricco, Antonio J.

    1993-01-01

    A method and apparatus for sensing a liquid-solid phase transition event is provided which comprises an acoustic plate mode detecting element placed in contact with a liquid or solid material which generates a high-frequency acoustic wave that is attenuated to an extent based on the physical state of the material is contact with the detecting element. The attenuation caused by the material in contact with the acoustic plate mode detecting element is used to determine the physical state of the material being detected. The method and device are particularly suited for detecting conditions such as the icing and deicing of wings of an aircraft. In another aspect of the present invention, a method is provided wherein the adhesion of a solid material to the detecting element can be measured using the apparatus of the invention.

  9. Acoustic wave device using plate modes with surface-parallel displacement

    DOE Patents [OSTI]

    Martin, Stephen J.; Ricco, Antonio J.

    1992-01-01

    Solid-state acoustic sensors for monitoring conditions at a surface immersed in a liquid and for monitoring concentrations of species in a liquid and for monitoring electrical properties of a liquid are formed by placing interdigital input and output transducers on a piezoelectric substrate and propagating acoustic plate modes therebetween. The deposition or removal of material on or from, respectively, a thin film in contact with the surface, or changes in the mechanical properties of a thin film in contact with the surface, or changes in the electrical characteristics of the solution, create perturbations in the velocity and attenuation of the acoustic plate modes as a function of these properties or changes in them.

  10. Acoustic wave device using plate modes with surface-parallel displacement

    DOE Patents [OSTI]

    Martin, S.J.; Ricco, A.J.

    1992-05-26

    Solid-state acoustic sensors for monitoring conditions at a surface immersed in a liquid and for monitoring concentrations of species in a liquid and for monitoring electrical properties of a liquid are formed by placing interdigital input and output transducers on a piezoelectric substrate and propagating acoustic plate modes there between. The deposition or removal of material on or from, respectively, a thin film in contact with the surface, or changes in the mechanical properties of a thin film in contact with the surface, or changes in the electrical characteristics of the solution, create perturbations in the velocity and attenuation of the acoustic plate modes as a function of these properties or changes in them. 6 figs.

  11. Homogenization of a thin plate reinforced with periodic families of rigid rods

    SciTech Connect (OSTI)

    Nazarov, Sergei A; Sweers, Guido H; Slutskij, Andrey S

    2011-08-31

    The asymptotics of the solution to the elastic bending problem for a thin plate reinforced with several periodic families of closely spaced but disjoint rods are constructed and justified, the result of homogenization being substantially different from the case when the rods are welded together into a single periodic mesh. The material in the rods is assumed to be appreciably more rigid than that in the plate. An averaged fourth-order differential operator is obtained from summing the nonelliptic operators generated by each of the families of the rods. This operator is shown to be elliptic if and only if the rods from at least two families are nonparallel. As a simplified example, the paper examines a similar stationary heat conduction problem. Bibliography: 24 titles.

  12. Broadband asymmetric acoustic transmission by a plate with quasi-periodic surface ridges

    SciTech Connect (OSTI)

    Li, Chunhui; Ke, Manzhu Ye, Yangtao; Xu, Shengjun; Qiu, Chunyin; Liu, Zhengyou

    2014-07-14

    In this paper, an acoustic system with broadband asymmetric transmission is designed and fabricated, which consists of a water-immersed aluminum plate engraved with quasi-periodically-patterned ridges on single surface. It demonstrates that when the acoustic waves are launched into the system from the structured side, they can couple into the Lamb modes in the plate efficiently and attain a high transmission; on the contrary, when the waves are incident from the opposite flat side, the coupling is weak, and the transmission is low. Superior to systems with periodic patterning, this quasi-periodically-patterned system has a broad working frequency range due to the collective contributions from the multiple diffractions specific to the structure.

  13. Method for preparing surfaces of metal composites having a brittle phase for plating

    DOE Patents [OSTI]

    Coates, Cameron W.; Wilson, Thomas J.

    1984-01-01

    The present invention is directed to a method for preparing surfaces of two-phase metal composites having relatively brittle and malleable components for plating with corrosion-resistant material. In practice of the present invention, the surfaces of the composites are etched to remove a major portion or fraction of the brittle component. The etched surface is then peened with particulates for breaking the brittle component from the surfaces and for spreading or smearing the malleable component over the surfaces. The peened surface is then chemically cleaned of residual traces of the brittle component so as to provide a surface of essentially the malleable component to which the corrosion-resistant material may be plated thereon in an adherent manner.

  14. Continious production of exfoliated graphite composite compositions and flow field plates

    DOE Patents [OSTI]

    Shi, Jinjun (Columbus, OH); Zhamu, Aruna (Centerville, OH); Jang, Bor Z. (Centerville, OH)

    2010-07-20

    A process of continuously producing a more isotropic, electrically conductive composite composition is provided. The process comprises: (a) continuously supplying a compressible mixture comprising exfoliated graphite worms and a binder or matrix material, wherein the binder or matrix material is in an amount of between 3% and 60% by weight based on the total weight of the mixture; (b) continuously compressing the compressible mixture at a pressure within the range of from about 5 psi or 0.035 MPa to about 50,000 psi or 350 MPa in at least a first direction into a cohered graphite composite compact; and (c) continuously compressing the composite compact in a second direction, different from the first direction, to form the composite composition in a sheet or plate form. The process leads to composite plates with exceptionally high thickness-direction electrical conductivity.

  15. Electroless nickel and ion-plated protective coatings for silvered glass mirrors

    SciTech Connect (OSTI)

    Lind, M.A.; Chaudiere, D.A.; Dake, L.S.; Stewart, T.L.

    1982-04-01

    A preliminary examination of two methods of protecting second surface silvered glass mirrors from environmental degradation is presented. One method employed silver mirrors overcoated with Al, Ni, 304 stainless steel, Cr, or an Al/Cu alloy prepared by ion-plating. The other method used conventional wet process silver mirrors protected with a thin electroless nickel coating. No attempt was made to optimize the coatings for either method. These experimental mirrors were compared with conventional paint backed silver/copper mirrors after exposure to elevated temperatures and water vapor in order to estimate their relative environmental stability. The electroless nickel mirrors showed consistently more resistance to these stresses than either the conventional or ion-plated mirrors, suggesting that they may provide more durable field service.

  16. Flexture plate motion-transfer mechanism, beam-splitter assembly, and interferometer incorporating the same

    DOE Patents [OSTI]

    Carangelo, R.M.; Dettori, M.D.; Grigely, L.J.; Murray, T.C.; Solomon, P.R.; Dine, C.P. Van; Wright, D.D.

    1996-01-23

    A multiplicity of one-piece flexure plates are assembled in pairs to provide a support system on which a retroreflector may be mounted for reciprocal motion. Combined with balance bodies, the flexure plates provide a support system having portions that are dynamically and statically balanced with one another, irrespective of orientation, so as to thereby immunize the unit against extraneous forces. The motion transfer assembly is especially adapted for use to support a moving retroreflector in a two-arm interferometer that may further include a beamsplitter assembly constructed from a one-piece, integrally formed body, the body having convergent, optically flat planar surfaces of specular reflectance, and means for adjustably mounting a beamsplitter therein. The spectrometer is of modular construction, and employs an integrated clocking sub-assembly as well as a light-weight voice-coil motor. 15 figs.

  17. Flexture plate motion-transfer mechanism, beam-splitter assembly, and interferometer incorporating the same

    DOE Patents [OSTI]

    Carangelo, Robert M.; Dettori, Mark D.; Grigely, Lawrence J.; Murray, Terence C.; Solomon, Peter R.; Van Dine, C. Peter; Wright, David D.

    1996-01-01

    A multiplicity of one-piece flexure plates are assembled in pairs to provide a support system on which a retroreflector may be mounted for reciprocal motion. Combined with balance bodies, the flexure plates provide a support system having portions that are dynamically and statically balanced with one another, irrespective of orientation, so as to thereby immunize the unit against extraneous forces. The motion transfer assembly is especially adapted for use to support a moving retroreflector in a two-arm interferometer that may further include a beamsplitter assembly constructed from a one-piece, integrally formed body, the body having convergent, optically flat planar surfaces of specular reflectance, and means for adjustably mounting a beamsplitter therein. The spectrometer is of modular construction, and employs an integrated clocking sub-assembly as well as a light-weight voice-coil motor.

  18. Proceedings of the flat-plate solar array project research forum on photovoltaic metallization systems

    SciTech Connect (OSTI)

    1983-11-15

    A Photovoltaic Metallization Research Forum, under the sponsorship of the Jet Propulsion Laboratory's Flat-Plate Solar Array Project and the US Department of Energy, was held March 16-18, 1983 at Pine Mountain, Georgia. The Forum consisted of five sessions, covering (1) the current status of metallization systems, (2) system design, (3) thick-film metallization, (4) advanced techniques and (5) future metallization challenges. Twenty-three papers were presented.

  19. New Zone Plate for Soft X-Ray Microscopy at 15-nm Spatial Resolution

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    New Zone Plate for Soft X-Ray Microscopy at 15-nm Spatial Resolution Print Analytical tools that combine spatial resolution with elemental and chemical identification at the nanometer scale along with large penetration depth are indispensable for the life and physical sciences. The XM-1 soft x-ray microscope at the ALS produces images that not only reveal structures but can identify their chemical elements and measure magnetic and other properties as well. Now a new method for creating optical

  20. New Zone Plate for Soft X-Ray Microscopy at 15-nm Spatial Resolution

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    New Zone Plate for Soft X-Ray Microscopy at 15-nm Spatial Resolution Print Analytical tools that combine spatial resolution with elemental and chemical identification at the nanometer scale along with large penetration depth are indispensable for the life and physical sciences. The XM-1 soft x-ray microscope at the ALS produces images that not only reveal structures but can identify their chemical elements and measure magnetic and other properties as well. Now a new method for creating optical