Sample records for uninterruptible power supplies

  1. Covered Product Category: Uninterruptible Power Supplies (for...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Applications) Covered Product Category: Uninterruptible Power Supplies (for Data Center, Computer, and Telecommunication Applications) The Federal Energy Management...

  2. Uninterruptible power supply (UPS) systems

    SciTech Connect (OSTI)

    NONE

    1997-04-01T23:59:59.000Z

    Use of this purchase specification is not mandatory. User should review the document and determine if it meets the user`s purpose. This document contains a fill-in-the-blanks guide specification for the procurement of uninterruptible power supply (UPS) systems greater than 10 kVA, organized as follows: Parts 1 through 7--technical requirements; Appendix A--technical requirements to be included in the proposal; Appendix B--UPS system data sheets to be completed by each bidder (Seller) and submitted with the proposal; Appendix C--general guidelines giving the specifier parameters for selecting a UPS system; it should be read before preparing an actual specification, and is not attached to the specification; Attachment 1--sketches prepared by the purchaser (Owner); Attachment 2--sample title page.

  3. Direct current uninterruptible power supply method and system

    DOE Patents [OSTI]

    Sinha, Gautam

    2003-12-02T23:59:59.000Z

    A method and system are described for providing a direct current (DC) uninterruptible power supply with the method including, for example: continuously supplying fuel to a turbine; converting mechanical power from the turbine into alternating current (AC) electrical power; converting the AC electrical power to DC power within a predetermined voltage level range; supplying the DC power to a load; and maintaining a DC load voltage within the predetermined voltage level range by adjusting the amount of fuel supplied to the turbine.

  4. Covered Product Category: Uninterruptible Power Supplies (for Data Center, Computer, and Telecommunication Applications)

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including uninterruptible power supplies (UPS), which are covered by the ENERGY STAR® program. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  5. EOI Uninterruptable Power Supply | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power AdministrationField Campaign:INEA :Work4/11 ENVIROISSUES PAGE 01/24/2005 04:22EOI

  6. Energy-efficient uninterruptible power supplies and switchmode power supplies for office technology

    SciTech Connect (OSTI)

    Eyer, J.

    1995-12-01T23:59:59.000Z

    There are three aspects of energy performance. The first is efficiency, and it specifically affects fuel use and the amount of emissions produced in relation to the amount of energy used and the fuel mix used in generation plants. Heat is rejected into the space with the result being additional air-conditioning to remove the heat. This often affects the capacity of the air-conditioning system. Customer electric bills are higher when more energy is used. The next important aspect of energy performance is peak electric demand. The capital requirements that utilities must put in place to deliver power to the customer affect many decisions made about energy efficiency and reduction of energy use. The capital requirements comprise 70 to 80% of the cost of delivering electricity to customers, while the fuel and variable costs associated with actually generating electricity are relatively small-20 to 30% of the total costs. In many respects, demand-side management programs are focused on reducing the need for increased capital equipment. Another aspect of energy performance is power quality. This is an important ally issue that could be addressed with initiatives similar to those for energy efficiency. Most power quality problems are related to current harmonics. Electronic equipment commonly reflects current harmonics back into the system, producing significant effects on the capacity of the system to deliver power. Immunity to poor power quality may be the most important aspect in receiving the benefits of improved power quality and power-conditioned equipment. Immunity is defined by the Computer and Business Equipment Manufacturers Association curve, which defines how `robust` the power supply must be with particular respect to low voltages. The immunity to different power quality problems could be dramatically improved by using existing technologies.

  7. Aging Management Guideline for commercial nuclear power plants: Battery chargers, inverters and uninterruptible power supplies. Final report

    SciTech Connect (OSTI)

    Berg, R.; Stroinski, M.; Giachetti, R. [Multiple Dynamics Corp., Southfield, MI (United States)

    1994-02-01T23:59:59.000Z

    This Aging Management Guideline (AMG) describes recommended methods for effective detection and mitigation of age-related degradation mechanisms in BWR and PWR commercial nuclear power plant battery chargers, inverters and uninterruptible power supplies important to license renewal. The intent of this AMG is to assist plant maintenance and operations personnel in maximizing the safe, useful life of these components. It also supports the documentation of effective aging management programs required under the License Renewal Rule 10 CFR Part 54. This AMG is presented in a manner that allows personnel responsible for performance analysis and maintenance to compare their plant-specific aging mechanisms (expected or already, experienced) and aging management program activities to the more generic results and recommendations presented herein.

  8. Uninterruptible Power Supply (UPS) Information and Instructions for How to Reset Them

    E-Print Network [OSTI]

    Oliver, Douglas L.

    indicates that there is power available to the UPS unit o The "BATERY" light indicates that power is being

  9. 3000 and 3000RM Uninterruptible Power Supplies

    E-Print Network [OSTI]

    Berns, Hans-Gerd

    . Recycling is the best method. Never burn batteries to dispose of them. They may explode. Do not open START OUTPUT LOAD OVERLOAD 100% 75% 50% 25% LINE PRESENT LINE FAILURE SERVICE LOW BATTERY WARNING LOW BATTERY SHUTDOWN TEST #12;CFR 3000 and 3000RM NOTICE: The CFR 3000 and 3000RM generates, uses and can

  10. Covered Product Category: Uninterruptible Power Supplies (for Data Center,

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: Theof"Wave theJuly 30, 2013DepartmentEnterpriseDepartmentofRoom

  11. Switching power supply

    DOE Patents [OSTI]

    Mihalka, A.M.

    1984-06-05T23:59:59.000Z

    The invention is a repratable capacitor charging, switching power supply. A ferrite transformer steps up a dc input. The transformer primary is in a full bridge configuration utilizing power MOSFETs as the bridge switches. The transformer secondary is fed into a high voltage, full wave rectifier whose output is connected directly to the energy storage capacitor. The transformer is designed to provide adequate leakage inductance to limit capacitor current. The MOSFETs are switched to the variable frequency from 20 to 50 kHz to charge a capacitor from 0.6 kV. The peak current in a transformer primary and secondary is controlled by increasing the pulse width as the capacitor charges. A digital ripple counter counts pulses and after a preselected desired number is reached an up-counter is clocked.

  12. Power Supply Synchronization without Communication

    E-Print Network [OSTI]

    Moehlis, Jeff

    1 Power Supply Synchronization without Communication Leonardo A. B. T^orres, Jo~ao P. Hespanha, Jeff Moehlis Abstract--We consider the synchronization of power supplies in an isolated grid with multiple small-to-medium power sources. We show how to achieve a coordinated or synchronized behavior

  13. Reliability Estimates for Power Supplies

    SciTech Connect (OSTI)

    Lee C. Cadwallader; Peter I. Petersen

    2005-09-01T23:59:59.000Z

    Failure rates for large power supplies at a fusion facility are critical knowledge needed to estimate availability of the facility or to set priorties for repairs and spare components. A study of the "failure to operate on demand" and "failure to continue to operate" failure rates has been performed for the large power supplies at DIII-D, which provide power to the magnet coils, the neutral beam injectors, the electron cyclotron heating systems, and the fast wave systems. When one of the power supplies fails to operate, the research program has to be either temporarily changed or halted. If one of the power supplies for the toroidal or ohmic heating coils fails, the operations have to be suspended or the research is continued at de-rated parameters until a repair is completed. If one of the power supplies used in the auxiliary plasma heating systems fails the research is often temporarily changed until a repair is completed. The power supplies are operated remotely and repairs are only performed when the power supplies are off line, so that failure of a power supply does not cause any risk to personnel. The DIII-D Trouble Report database was used to determine the number of power supply faults (over 1,700 reports), and tokamak annual operations data supplied the number of shots, operating times, and power supply usage for the DIII-D operating campaigns between mid-1987 and 2004. Where possible, these power supply failure rates from DIII-D will be compared to similar work that has been performed for the Joint European Torus equipment. These independent data sets support validation of the fusion-specific failure rate values.

  14. Power Supply Negotiations

    Office of Environmental Management (EM)

    Southeastern Federal Power Alliance Incremental Decay in Energy March 11, 2014 2 Incremental Decay in Energy Hydropower customers observations from our review of the Buford...

  15. Power Supply Challenges

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn'tOrigin of Contamination in235-1Department of60Power Purchase Agreements Power Purchase Agreements

  16. Power Right. Power Smart. Efficient Computer Power Supplies and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AC power that you get from your electric company into the DC power consumed by most electronics, including your computer. We expect our power supplies to be safe, reliable, and...

  17. High voltage DC power supply

    DOE Patents [OSTI]

    Droege, Thomas F. (Batavia, IL)

    1989-01-01T23:59:59.000Z

    A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively.

  18. High voltage DC power supply

    DOE Patents [OSTI]

    Droege, T.F.

    1989-12-19T23:59:59.000Z

    A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively. 7 figs.

  19. Fastbus Power Supply Manual University of Washington Seattle, 26 March, 1996 Fastbus Power Supplies

    E-Print Network [OSTI]

    Berns, Hans-Gerd

    supplies each have their own built­in cooling fans, and the lower­current supplies are sufficiently cooledFastbus Power Supply Manual University of Washington Seattle, 26 March, 1996 page 1 Fastbus Power Supplies HGB, 03/26/1996 Overview Each of the four Fastbus crates of the SuperK OD DAQ system is supplied

  20. Advanced Accessory Power Supply Topologies

    SciTech Connect (OSTI)

    Marlino, L.D.

    2010-06-15T23:59:59.000Z

    This Cooperative Research and Development Agreement (CRADA) began December 8, 2000 and ended September 30, 2009. The total funding provided by the Participant (General Motors Advanced Technology Vehicles [GM]) during the course of the CRADA totaled $1.2M enabling the Contractor (UT-Battelle, LLC [Oak Ridge National Laboratory, a.k.a. ORNL]) to contribute significantly to the joint project. The initial task was to work with GM on the feasibility of developing their conceptual approach of modifying major components of the existing traction inverter/drive to develop low cost, robust, accessory power. Two alternate methods for implementation were suggested by ORNL and both were proven successful through simulations and then extensive testing of prototypes designed and fabricated during the project. This validated the GM overall concept. Moreover, three joint U.S. patents were issued and subsequently licensed by GM. After successfully fulfilling the initial objective, the direction and duration of the CRADA was modified and GM provided funding for two additional tasks. The first new task was to provide the basic development for implementing a cascaded inverter technology into hybrid vehicles (including plug-in hybrid, fuel cell, and electric). The second new task was to continue the basic development for implementing inverter and converter topologies and new technology assessments for hybrid vehicle applications. Additionally, this task was to address the use of high temperature components in drive systems. Under this CRADA, ORNL conducted further research based on GM’s idea of using the motor magnetic core and windings to produce bidirectional accessory power supply that is nongalvanically coupled to the terminals of the high voltage dc-link battery of hybrid vehicles. In order not to interfere with the motor’s torque, ORNL suggested to use the zero-sequence, highfrequency harmonics carried by the main fundamental motor current for producing the accessory power. Two studies were conducted at ORNL. One was to put an additional winding in the motor slots to magnetically link with the high frequency of the controllable zero-sequence stator currents that do not produce any zero-sequence harmonic torques. The second approach was to utilize the corners of the square stator punching for the high-frequency transformers of the dc/dc inverter. Both approaches were successful. This CRADA validated the feasibility of GM’s desire to use the motor’s magnetic core and windings to produce bidirectional accessory power supply. Three joint U.S. patents with GM were issued to ORNL and GM by the U.S. Patent Office for the research results produced by this CRADA.

  1. Shock-activated electrochemical power supplies

    DOE Patents [OSTI]

    Benedick, W.B.; Graham, R.A.; Morosin, B.

    1988-11-08T23:59:59.000Z

    A shock-activated electrochemical power supply is provided which is initiated extremely rapidly and which has a long shelf life. Electrochemical power supplies of this invention are initiated much faster than conventional thermal batteries. Power supplies of this invention comprise an inactive electrolyte and means for generating a high-pressure shock wave such that the shock wave is propagated through the electrolytes rendering the electrolyte electrochemically active. 2 figs.

  2. Shock-activated electrochemical power supplies

    DOE Patents [OSTI]

    Benedick, W.B.; Graham, R.A.; Morosin, B.

    1987-04-20T23:59:59.000Z

    A shock-activated electrochemical power supply is provided which is initiated extremely rapidly and which has a long shelf life. Electrochemical power supplies of this invention are initiated much faster than conventional thermal batteries. Power supplies of this invention comprise an inactive electrolyte and means for generating a high-pressure shock wave such that the shock wave is propagated through the electrolyte rendering the electrolyte electrochemically active. 2 figs.

  3. Hierarchical Hybrid Power Supply Networks Farinaz Koushanfar

    E-Print Network [OSTI]

    management, hybrid power supply, supercapacitors 1. INTRODUCTION AND MOTIVATION Historically, almost all in a hierarchical power sup- ply network would include batteries, supercapacitors, ionic supercapacitors, and future cycle, supercapacitors are advantageous rel- ative to the standard che

  4. CONCEPTUAL DESIGN STUDY OF HORN POWER SUPPLY.

    SciTech Connect (OSTI)

    ZHANG,W.; SANDBERG,J.; WENG,W.T.

    2003-06-16T23:59:59.000Z

    A 250 kA pulsed power supply is required for the focusing horn of the proposed Brookhaven AGS Super Neutrino Beam Facility for long baseline neutrino oscillation experiment. It is expected to pulse at 2.5 Hz repetition rate. A preliminary study is being conducted to explore the key issues associated with the power supply system design. Advanced technologies used in similar systems as well as new ideas are being examined, simulated and evaluated. This power supply will be a very high stored energy, high average power, and high peak power system.

  5. E951 POWER SUPPLY SAFETY REVIEW

    E-Print Network [OSTI]

    McDonald, Kirk

    E951 POWER SUPPLY SAFETY REVIEW 9/06/02 IOANNIS MARNERIS Brookhaven National Labs. #12;Project. · To do this we will use 4 existing SCR type dc power supplies from the experimental area in series 3644 Voltage (V) 150 300 300 Peakcurrent (A) 3600 7200 7200 Field (T) 5.0 10.0 14.5 Inductance (mH) 138

  6. Power supply noise in delay testing 

    E-Print Network [OSTI]

    Wang, Jing

    2009-05-15T23:59:59.000Z

    As technology scales into the Deep Sub-Micron (DSM) regime, circuit designs have become more and more sensitive to power supply noise. Excessive noise can significantly affect the timing performance of DSM designs and cause ...

  7. Dynamic Electric Power Supply Chains and Transportation Networks

    E-Print Network [OSTI]

    Nagurney, Anna

    Dynamic Electric Power Supply Chains and Transportation Networks: an Evolutionary Variational energy Electric power supply chains, provide the foundations for theElectric power supply chains, provide and societies. Communication, transportation, heating, lighting, cooling,Communication, transportation, heating

  8. Engine Driven Combined Heat and Power: Arrow Linen Supply, December...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Engine Driven Combined Heat and Power: Arrow Linen Supply, December 2008 Engine Driven Combined Heat and Power: Arrow Linen Supply, December 2008 This paper describes the Arrow...

  9. High power fast ramping power supplies

    SciTech Connect (OSTI)

    Marneris,I.; Bajon, E.; Bonati, R.; Sandberg, J.; Roser, T.; Tsoupas, N.

    2009-05-04T23:59:59.000Z

    Hundred megawatt level fast ramping power converters to drive proton and heavy ion machines are under research and development at accelerator facilities in the world. This is a leading edge technology. There are several topologies to achieve this power level. Their advantages and related issues will be discussed.

  10. Power-Supply-Network Design in 3D Integrated Systems

    E-Print Network [OSTI]

    Lim, Sung Kyu

    Power-Supply-Network Design in 3D Integrated Systems Michael B. Healy and Sung Kyu Lim School power-supply noise in a layout- level 3D design prototype, and the impact of possible 3D-specific changes to the power-supply network design and topology. Our results show that distributing power-supply

  11. Pacific Northwest Power Supply Adequacy Assessment

    E-Print Network [OSTI]

    . Based on an assessment prepared by the Resource Adequacy Forum, the plan noted that relying only that this assessment is not a substitute for a comprehensive resource acquisition plan. The optimal amount and mixPacific Northwest Power Supply Adequacy Assessment for 2017 Final Report November 21, 2012 Council

  12. Uninterruptible Power Supplies Designed to meet or exceed the safety standards established by UL, CSA, CE and VDE. The Alpha CFR UPS is one of the safest, most reliable and versatile Uninterruptible Power Systems

    E-Print Network [OSTI]

    Berns, Hans-Gerd

    % Load 88% 90% 90% 90% 90% 90% Typical Heat Output - Line Mode 209 BTU/h 284 BTU/h 427 BTU/h 427 BTU/h 398 BTU/h 636 BTU/h Mechanical Width (in \\ mm) 8.5 \\ 216 8.5 \\ 216 8.5 \\ 216 8.5 \\ 216 8.5 \\ 216 8

  13. A single power supply optoelectronic differential amplifier

    E-Print Network [OSTI]

    Choi, Youngmin Albert

    1987-01-01T23:59:59.000Z

    Coinmittee: Henry F. Taylor This thesis presents an approach to optoelectronic differential amplifier (ODA) design in which two avalanche photodiodes and two laser diodes are used instead of a rriatched pair of transistors. The approach is demonstrated... by the design and realization oi' a complete system which includes direct intensity modulation of laser diodes and a novel single power supply optical receiver. The ODA shows better than 25 dB common-mode rejection ratio (CMRR) over a bandwidth of greater...

  14. SPEAR3 LARGE DC MAGNET POWER SUPPLIES

    SciTech Connect (OSTI)

    de Lira, A

    2004-06-23T23:59:59.000Z

    The Stanford Synchrotron Radiation Laboratory (SSRL) has successfully commissioned SPEAR3, its newly upgraded 3-GeV synchrotron light source. First stored beam occurred December 15, 2003 and 100mA operation was reached on January 20, 2004. This paper describes the specification, design, and performance of the SPEAR3 DC magnet large power supplies (LGPS) that consist of tightly-regulated (better than {+-}10 ppm) current sources ranging from 100A to 225A and output powers ranging from 70kW to 135kW. A total of 6 LGPS are in successful operation and are used to power strings of quadrupoles and sextupoles. The LGPS are isolated by a delta/delta-wye 60Hz step-down transformer that provides power to 2 series-connected chopper stages operating phase-shifted at a switching frequency of 18-kHz to provide for fast output response and high efficiency. Also described are outside procurement aspects, installation, in-house testing, and operation of the power supplies.

  15. Emergency and backup power supplies at Department of Energy facilities: Augmented Evaluation Team -- Final report

    SciTech Connect (OSTI)

    Not Available

    1993-11-01T23:59:59.000Z

    This report documents the results of the Defense Programs (DP) Augmented Evaluation Team (AET) review of emergency and backup power supplies (i.e., generator, uninterruptible power supply, and battery systems) at DP facilities. The review was conducted in response to concerns expressed by former Secretary of Energy James D. Watkins over the number of incidents where backup power sources failed to provide electrical power during tests or actual demands. The AET conducted a series of on-site reviews for the purpose of understanding the design, operation, maintenance, and safety significance of emergency and backup power (E&BP) supplies. The AET found that the quality of programs related to maintenance of backup power systems varies greatly among the sites visited, and often among facilities at the same site. No major safety issues were identified. However, there are areas where the AET believes the reliability of emergency and backup power systems can and should be improved. Recommendations for improving the performance of E&BP systems are provided in this report. The report also discusses progress made by Management and Operating (M&O) contractors to improve the reliability of backup sources used in safety significant applications. One area that requires further attention is the analysis and understanding of the safety implications of backup power equipment. This understanding is needed for proper graded-approach implementation of Department of Energy (DOE) Orders, and to help ensure that equipment important to the safety of DOE workers, the public, and the environment is identified, classified, recognized, and treated as such by designers, users, and maintainers. Another area considered important for improving E&BP system performance is the assignment of overall ownership responsibility and authority for ensuring that E&BP equipment performs adequately and that reliability and availability are maintained at acceptable levels.

  16. Hydrogen storage of energy for small power supply systems

    E-Print Network [OSTI]

    Monaghan, Rory F. D. (Rory Francis Desmond)

    2005-01-01T23:59:59.000Z

    Power supply systems for cell phone base stations using hydrogen energy storage, fuel cells or hydrogen-burning generators, and a backup generator could offer an improvement over current power supply systems. Two categories ...

  17. THE JET PULSE POWER SUPPLY SYSTEM J. B. HICKS

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    between the two major components of the power supply (flywheel-generator-convertors (FGC) and transformer between the two possible components of the power supply, i. e. flywheel. generator-convertors and transformer-controlled-convertors. The proposed JET power supply system is described, together with an outline

  18. agricultural power supply: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Abstract-- With each technology generation, the power computationally complex. The rising number of on-chip power supplies and intentional decoupling capacitors Friedman, Eby G. 37...

  19. auxiliary power supply: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Abstract-- With each technology generation, the power computationally complex. The rising number of on-chip power supplies and intentional decoupling capacitors Friedman, Eby G. 45...

  20. area power supply: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Abstract-- With each technology generation, the power computationally complex. The rising number of on-chip power supplies and intentional decoupling capacitors Friedman, Eby G. 37...

  1. availability power supply: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Abstract-- With each technology generation, the power computationally complex. The rising number of on-chip power supplies and intentional decoupling capacitors Friedman, Eby G. 37...

  2. A Supply Chain Network Perspective for Electric Power Generation, Supply, Transmission, and Consumption

    E-Print Network [OSTI]

    Nagurney, Anna

    A Supply Chain Network Perspective for Electric Power Generation, Supply, Transmission, and Consumption Anna Nagurney and Dmytro Matsypura Department of Finance and Operations Management Isenberg School, Berlin, Germany, pp. 3-27. Abstract: A supply chain network perspective for electric power production

  3. A Fuel Cell Power Supply for Long Duration Balloon Flights Using Stored Cryogens

    E-Print Network [OSTI]

    Green, Michael A.; Manikowski, A.; Noland, G.; Golden, R.L.

    1997-01-01T23:59:59.000Z

    CA, (1966) LBNL-40618 A FUEL CELL POWER SUPPLY FOR LONGLBNL-40618 A FUEL CELL POWER SUPPLY FOR LONG DURATIONreport describes a fuel cell power supply configuration.

  4. High performance magnet power supply optimization

    SciTech Connect (OSTI)

    Jackson, L.T.

    1988-01-01T23:59:59.000Z

    The power supply system for the joint LBL--SLAC proposed accelerator PEP provides the opportunity to take a fresh look at the current techniques employed for controlling large amounts of dc power and the possibility of using a new one. A basic requirement of +- 100 ppM regulation is placed on the guide field of the bending magnets and quadrupoles placed around the 2200 meter circumference of the accelerator. The optimization questions to be answered by this paper are threefold: Can a firing circuit be designed to reduce the combined effects of the harmonics and line voltage combined effects of the harmonics and line voltage unbalance to less than 100 ppM in the magnet field. Given the ambiguity of the previous statement, is the addition of a transistor bank to a nominal SCR controlled system the way to go or should one opt for an SCR chopper system running at 1 KHz where multiple supplies are fed from one large dc bus and the cost--performance evaluation of the three possible systems.

  5. Power Supplies and Radio Frequency Department at Culham

    E-Print Network [OSTI]

    Power Supplies and Radio Frequency Department at Culham Culham Centre for Fusion Energy #12;We employ over 70 power electrical and power electronic engineers and technicians. The department supplies power to the JET and MAST nuclear fusion experiments at Culham. Culham is fed from the grid at 400k

  6. Controlled Use Robot Colony Power Supply Gary Parker

    E-Print Network [OSTI]

    Parker, Gary B.

    Controlled Use Robot Colony Power Supply Gary Parker Computer Science Connecticut College New.S.A. rszbe@conncoll.edu Abstract ­ controlled of a continuous power supply robots colony presented. builds at a power station. onboard controller implemented to direct hexapod colony robot behavior according power

  7. E-beam high voltage switching power supply

    DOE Patents [OSTI]

    Shimer, D.W.; Lange, A.C.

    1996-10-15T23:59:59.000Z

    A high-power power supply produces a controllable, constant high voltage output under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules. 5 figs.

  8. E-beam high voltage switching power supply

    DOE Patents [OSTI]

    Shimer, Daniel W. (Danville, CA); Lange, Arnold C. (Livermore, CA)

    1996-01-01T23:59:59.000Z

    A high-power power supply produces a controllable, constant high voltage put under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules.

  9. Centre Hydraulic Power Supply Unit University of Saskatchewan -Mechanical Engineering Fluid Power and Controls

    E-Print Network [OSTI]

    Saskatchewan, University of

    Centre Hydraulic Power Supply Unit University of Saskatchewan - Mechanical Engineering ­ Fluid Power and Controls ID: FP0003 Rev: 001 Date: May 31, 2010 Page: 1 of 7 Centre Hydraulic Power Supply;Centre Hydraulic Power Supply Unit University of Saskatchewan - Mechanical Engineering ­ Fluid Power

  10. QER- Comment of Electric Power Supply Association 2

    Broader source: Energy.gov [DOE]

    Please find the attached comments of the Electric Power Supply Association on the Department of Energy’s Quadrennial Energy Review due October 10, 2014. Respectfully submitted,

  11. QER- Comment of Electric Power Supply Association 3

    Broader source: Energy.gov [DOE]

    Please find the attached comments of the Electric Power Supply Association on the Department of Energy’s Quadrennial Energy Review due October 10, 2014. Respectfully submitted,

  12. QER- Comment of Electric Power Supply Association 4

    Broader source: Energy.gov [DOE]

    Please find the attached comments of the Electric Power Supply Association on the Department of Energy’s Quadrennial Energy Review due October 10, 2014.

  13. QER- Comment of Electric Power Supply Association 1

    Broader source: Energy.gov [DOE]

    Please find the attached comments of the Electric Power Supply Association on the Department of Energy’s Quadrennial Energy Review due October 10, 2014. Respectfully submitted,

  14. HYPower Hydraulic Power Supply Unit University of Saskatchewan -Mechanical Engineering Fluid Power and Controls

    E-Print Network [OSTI]

    Saskatchewan, University of

    HYPower Hydraulic Power Supply Unit University of Saskatchewan - Mechanical Engineering ­ Fluid Power and Controls ID: FP0002 Rev: 002 Date: May 31, 2010 Page: 1 of 7 Hydraulic Power Supply (HYPower-5462 Secondary Contact: #12;HYPower Hydraulic Power Supply Unit University of Saskatchewan - Mechanical

  15. Modular high voltage power supply for chemical analysis

    DOE Patents [OSTI]

    Stamps, James F. (Livermore, CA); Yee, Daniel D. (Dublin, CA)

    2010-05-04T23:59:59.000Z

    A high voltage power supply for use in a system such as a microfluidics system, uses a DC-DC converter in parallel with a voltage-controlled resistor. A feedback circuit provides a control signal for the DC-DC converter and voltage-controlled resistor so as to regulate the output voltage of the high voltage power supply, as well as, to sink or source current from the high voltage supply.

  16. Modular high voltage power supply for chemical analysis

    SciTech Connect (OSTI)

    Stamps, James F. (Livermore, CA); Yee, Daniel D. (Dublin, CA)

    2007-01-09T23:59:59.000Z

    A high voltage power supply for use in a system such as a microfluidics system, uses a DC--DC converter in parallel with a voltage-controlled resistor. A feedback circuit provides a control signal for the DC--DC converter and voltage-controlled resistor so as to regulate the output voltage of the high voltage power supply, as well as, to sink or source current from the high voltage supply.

  17. Modular high voltage power supply for chemical analysis

    SciTech Connect (OSTI)

    Stamps, James F. (Livermore, CA); Yee, Daniel D. (Dublin, CA)

    2008-07-15T23:59:59.000Z

    A high voltage power supply for use in a system such as a microfluidics system, uses a DC-DC converter in parallel with a voltage-controlled resistor. A feedback circuit provides a control signal for the DC-DC converter and voltage-controlled resistor so as to regulate the output voltage of the high voltage power supply, as well as, to sink or source current from the high voltage supply.

  18. IntroductiontoPowerSuppliesAN-556 National Semiconductor

    E-Print Network [OSTI]

    Paderborn, Universität

    TL G 10061 IntroductiontoPowerSuppliesAN-556 National Semiconductor Application Note 556 Ralph E ripple voltage to capacitor C1 The bridge rectifier circuit has a simple transformer but current must in a full-wave bridge for the same input voltage TL G 10061­1 FIGURE 1 Idealized Power Supply TL G 10061

  19. Introduction Literature Review Integrated Electric Power Supply Chains Empirical Examples Conclusions An Integrated Electric Power Supply Chain and Fuel

    E-Print Network [OSTI]

    Nagurney, Anna

    of fuel demands 30% of the natural gas demand (over 50% in the summer) 90% of the coal demand over 45% of the residual fuel oil demand. #12;Introduction Literature Review Integrated Electric Power Supply ChainsIntroduction Literature Review Integrated Electric Power Supply Chains Empirical Examples

  20. Introduction Literature Review Integrated Electric Power Supply Chains Empirical Examples Conclusions An Integrated Electric Power Supply Chain and Fuel

    E-Print Network [OSTI]

    Nagurney, Anna

    % in the summer) 90% of the coal demand over 45% of the residual fuel oil demand. #12;Introduction LiteratureIntroduction Literature Review Integrated Electric Power Supply Chains Empirical Examples Conclusions An Integrated Electric Power Supply Chain and Fuel Market Network Framework: Theoretical Modeling

  1. Handling Food and Supplies during Power Loss

    E-Print Network [OSTI]

    Anding, Jenna

    2005-09-30T23:59:59.000Z

    This publication lists foods that are safe to eat without cooking or refrigeration. There is also a list of supplies you will need when gas and electrical service is unavailable....

  2. Optimal Endogenous Carbon Taxes Electric Power Supply Chains with Power Plants

    E-Print Network [OSTI]

    Nagurney, Anna

    Optimal Endogenous Carbon Taxes for Electric Power Supply Chains with Power Plants Anna Nagurney for the determination of optimal carbon taxes applied to electric power plants in the con- text of electric power supply portion of such policy inter- ventions directed at the electric power industry. The general framework

  3. Tokamak Physics Experiment (TPX) power supply design and development

    SciTech Connect (OSTI)

    Neumeyer, C. [Raytheon Engineers and Constructors, Princeton, NJ (United States). EBASCO Div.; Bronner, G.; Lu, E.; Ramakrishnan, S. [Princeton Univ., NJ (United States). Plasma Physics Lab.

    1995-04-01T23:59:59.000Z

    The Tokamak Physics Experiment (TPX) is an advanced tokamak project aimed at the production of quasi-steady state plasmas with advanced shape, heating, and particle control. TPX is to be built at the Princeton Plasma Physics Laboratory (PPPL) using many of the facilities from the Tokamak Fusion Test Reactor (TFTR). TPX will be the first tokamak to utilize superconducting (SC) magnets in both the toroidal field (TF) and poloidal field (PF) systems. This new feature requires a departure from the traditional tokamak power supply schemes. This paper describes the plan for the adaptation of the PPPL/FTR power system facilities to supply TPX. Five major areas are addressed, namely the AC power system, the TF, PF and Fast Plasma Position Control (FPPC) power supplies, and quench protection for the TF and PF systems. Special emphasis is placed on the development of new power supply and protection schemes.

  4. Digital control strategies for switch-mode power supply

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Digital control strategies for switch-mode power supply Xuefang Lin-Shi, Bruno Allard, Senior and a request for large regulation bandwidth. Digital control is now experi- mented for low-power low control. Fig. 1. Schematic synchronous step-down SMPS Digital control is not new in the field of Power

  5. The Homopolar Generator as a Pulsed Industrial Power Supply

    E-Print Network [OSTI]

    Weldon, J. M.; Weldon, W. F.

    1979-01-01T23:59:59.000Z

    power supply for numerous industrial applications such as large metal cross section pulsed resistance welding, pulsed billet heating for subsequent hot working processes, pulsed heating for localized forging processes, and magnetic metal forming. Each...

  6. The Homopolar Generator as a Pulsed Industrial Power Supply 

    E-Print Network [OSTI]

    Weldon, J. M.; Weldon, W. F.

    1979-01-01T23:59:59.000Z

    power supply for numerous industrial applications such as large metal cross section pulsed resistance welding, pulsed billet heating for subsequent hot working processes, pulsed heating for localized forging processes, and magnetic metal forming. Each...

  7. Custom power supply interface for teaching circuit design

    E-Print Network [OSTI]

    Madrigal, Ruben E. (Ruben Esteban)

    2014-01-01T23:59:59.000Z

    This thesis discusses the design and implementation of a custom power supply interface for the Pioneer mobile robot used in MIT's 6.01 course, "Introduction to Electrical Engineering and Computer Science." The interface ...

  8. Distributed Power Network Co-Design with On-Chip Power Supplies and Decoupling Capacitors

    E-Print Network [OSTI]

    Friedman, Eby G.

    Distributed Power Network Co-Design with On-Chip Power Supplies and Decoupling Capacitors Selc¸uk K, New York 14627 {kose,friedman}@ece.rochester.edu Abstract-- With each technology generation, the power computationally complex. The rising number of on-chip power supplies and intentional decoupling capacitors

  9. East Hydraulic Power Supply Unit University of Saskatchewan -Mechanical Engineering Fluid Power and Controls

    E-Print Network [OSTI]

    Saskatchewan, University of

    East Hydraulic Power Supply Unit University of Saskatchewan - Mechanical Engineering ­ Fluid Power and Controls ID: FP0004 Rev: 001 Date: May 31, 2010 Page: 1 of 7 East Hydraulic Power Supply and Test Bench. Approved By: Primary Contact: Doug Bitner Rm: 1B15.1 966-5462 Secondary Contact: #12;East Hydraulic Power

  10. 150-kV, 80-A SOLID STATE POWER SUPPLY FOR NEUTRAL BEAM INJECTION

    E-Print Network [OSTI]

    Owren, H.

    2011-01-01T23:59:59.000Z

    owned rig 150-kV, 80-A SOLID STATE POWER SUPPLY FOR NEUTRALpaper describes an all solid state power supply designed forment and arc power supplies are also solid state. With the

  11. Power Supply and Consumption Co-Optimization of Portable Embedded Systems with

    E-Print Network [OSTI]

    Pedram, Massoud

    Power Supply and Consumption Co-Optimization of Portable Embedded Systems with Hybrid Power Supply proposed. In this work, we consider a portable embedded system with a hybrid power supply and executing periodic real-time tasks. We perform system power management from both the power supply side and the power

  12. FOURFOUR--QUADRANT POWER SUPPLIESQUADRANT POWER SUPPLIES FOR STEERING ELECTROMAGNETSFOR STEERING ELECTROMAGNETS

    E-Print Network [OSTI]

    Kozak, Victor R.

    FOURFOUR--QUADRANT POWER SUPPLIESQUADRANT POWER SUPPLIES FOR STEERING ELECTROMAGNETSFOR STEERING-3 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - DIPOLE CORRECTORS MULTI-POLE CORRECTORS W500P kW2P Cooling: Air Natural IUP = V100U,A6I V100U,A25I.V.Belikov@inp.nsk.su Bulk Power Supply R S C I FOUR- QUADRANT POWER SUPPLIES RECUPERATION VCC H-BI #12;O. Belikov, Ru

  13. E-beam high voltage switching power supply

    DOE Patents [OSTI]

    Shimer, Daniel W. (Danville, CA); Lange, Arnold C. (Livermore, CA)

    1997-01-01T23:59:59.000Z

    A high power, solid state power supply is described for producing a controllable, constant high voltage output under varying and arcing loads suitable for powering an electron beam gun or other ion source. The present power supply is most useful for outputs in a range of about 100-400 kW or more. The power supply is comprised of a plurality of discrete switching type dc-dc converter modules, each comprising a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, and an output rectifier for producing a dc voltage at the output of each module. The inputs to the converter modules are fed from a common dc rectifier/filter and are linked together in parallel through decoupling networks to suppress high frequency input interactions. The outputs of the converter modules are linked together in series and connected to the input of the transmission line to the load through a decoupling and line matching network. The dc-dc converter modules are phase activated such that for n modules, each module is activated equally 360.degree./n out of phase with respect to a successive module. The phased activation of the converter modules, combined with the square current waveforms out of the step up transformers, allows the power supply to operate with greatly reduced output capacitance values which minimizes the stored energy available for discharge into an electron beam gun or the like during arcing. The present power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle using simulated voltage feedback signals and voltage feedback loops. Circuitry is also provided for sensing incipient arc currents reflected at the output of the power supply and for simultaneously decoupling the power supply circuitry from the arcing load.

  14. E-beam high voltage switching power supply

    DOE Patents [OSTI]

    Shimer, D.W.; Lange, A.C.

    1997-03-11T23:59:59.000Z

    A high power, solid state power supply is described for producing a controllable, constant high voltage output under varying and arcing loads suitable for powering an electron beam gun or other ion source. The present power supply is most useful for outputs in a range of about 100-400 kW or more. The power supply is comprised of a plurality of discrete switching type dc-dc converter modules, each comprising a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, and an output rectifier for producing a dc voltage at the output of each module. The inputs to the converter modules are fed from a common dc rectifier/filter and are linked together in parallel through decoupling networks to suppress high frequency input interactions. The outputs of the converter modules are linked together in series and connected to the input of the transmission line to the load through a decoupling and line matching network. The dc-dc converter modules are phase activated such that for n modules, each module is activated equally 360{degree}/n out of phase with respect to a successive module. The phased activation of the converter modules, combined with the square current waveforms out of the step up transformers, allows the power supply to operate with greatly reduced output capacitance values which minimizes the stored energy available for discharge into an electron beam gun or the like during arcing. The present power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle using simulated voltage feedback signals and voltage feedback loops. Circuitry is also provided for sensing incipient arc currents reflected at the output of the power supply and for simultaneously decoupling the power supply circuitry from the arcing load. 7 figs.

  15. Electrical Power Supply Applications Engineer | Princeton Plasma...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the services of an Electrical Engineer with experience in the design, procurement, commissioning, and operation of large electrical power systems and associated equipment for use...

  16. Modeling Generator Power Plant Portfolios and Pollution Taxes Electric Power Supply Chain Networks

    E-Print Network [OSTI]

    Nagurney, Anna

    than a third arises from generating electricity. With the accumulating evidence of global warming, any affect the equilibrium electric power supply chain network production outputs, the transactions betweenModeling Generator Power Plant Portfolios and Pollution Taxes in Electric Power Supply Chain

  17. Precision control of high temperature furnaces using an auxiliary power supply and charged practice current flow

    DOE Patents [OSTI]

    Pollock, George G. (San Ramon, CA)

    1997-01-01T23:59:59.000Z

    Two power supplies are combined to control a furnace. A main power supply heats the furnace in the traditional manner, while the power from the auxiliary supply is introduced as a current flow through charged particles existing due to ionized gas or thermionic emission. The main power supply provides the bulk heating power and the auxiliary supply provides a precise and fast power source such that the precision of the total power delivered to the furnace is improved.

  18. Precision control of high temperature furnaces using an auxiliary power supply and charged particle current flow

    DOE Patents [OSTI]

    Pollock, G.G.

    1997-01-28T23:59:59.000Z

    Two power supplies are combined to control a furnace. A main power supply heats the furnace in the traditional manner, while the power from the auxiliary supply is introduced as a current flow through charged particles existing due to ionized gas or thermionic emission. The main power supply provides the bulk heating power and the auxiliary supply provides a precise and fast power source such that the precision of the total power delivered to the furnace is improved. 5 figs.

  19. DIII-D ICRF high voltage power supply regulator upgrade

    SciTech Connect (OSTI)

    Cary, W.P.; Burley, B.L.; Grosnickle, W.H.

    1997-11-01T23:59:59.000Z

    For reliable operation and component protection, of the 2 MW 30--120 MHz ICRF Amplifier System on DIII-D, it is desirable for the amplifier to respond to high VSWR conditions as rapidly as possible. This requires a rapid change in power which also means a rapid change in the high voltage power supply current demands. An analysis of the power supply`s regulator dynamics was needed to verify its expected operation during such conditions. Based on this information it was found that a new regulator with a larger dynamic range and some anticipation capability would be required. This paper will discuss the system requirements, the as-delivered regulator performance, and the improved performance after installation of the new regulator system. It will also be shown how this improvement has made the amplifier perform at higher power levels more reliably.

  20. Fuel cell power supply with oxidant and fuel gas switching

    DOE Patents [OSTI]

    McElroy, James F. (Hamilton, MA); Chludzinski, Paul J. (Swampscott, MA); Dantowitz, Philip (Peabody, MA)

    1987-01-01T23:59:59.000Z

    This invention relates to a fuel cell vehicular power plant. Fuel for the fuel stack is supplied by a hydrocarbon (methanol) catalytic cracking reactor and CO shift reactor. A water electrolysis subsystem is associated with the stack. During low power operation part of the fuel cell power is used to electrolyze water with hydrogen and oxygen electrolysis products being stored in pressure vessels. During peak power intervals, viz, during acceleration or start-up, pure oxygen and pure hydrogen from the pressure vessel are supplied as the reaction gases to the cathodes and anodes in place of air and methanol reformate. This allows the fuel cell stack to be sized for normal low power/air operation but with a peak power capacity several times greater than that for normal operation.

  1. Fuel cell power supply with oxidant and fuel gas switching

    DOE Patents [OSTI]

    McElroy, J.F.; Chludzinski, P.J.; Dantowitz, P.

    1987-04-14T23:59:59.000Z

    This invention relates to a fuel cell vehicular power plant. Fuel for the fuel stack is supplied by a hydrocarbon (methanol) catalytic cracking reactor and CO shift reactor. A water electrolysis subsystem is associated with the stack. During low power operation part of the fuel cell power is used to electrolyze water with hydrogen and oxygen electrolysis products being stored in pressure vessels. During peak power intervals, viz, during acceleration or start-up, pure oxygen and pure hydrogen from the pressure vessel are supplied as the reaction gases to the cathodes and anodes in place of air and methanol reformate. This allows the fuel cell stack to be sized for normal low power/air operation but with a peak power capacity several times greater than that for normal operation. 2 figs.

  2. Outline Introduction Literature Review Electric Power Supply Chains Empirical Examples Conclusions An Integrated Electric Power Supply Chain and Fuel

    E-Print Network [OSTI]

    Nagurney, Anna

    .S., electric power generation accounts for significant portions of fuel demands 30% of the natural gas demand (over 50% in the summer) 90% of the coal demand over 45% of the residual fuel oil demand #12;OutlineOutline Introduction Literature Review Electric Power Supply Chains Empirical Examples Conclusions

  3. Power Compensation Effect of an Adjustable-Speed Rotary Condenser with a Flywheel for a Large Capacity Magnet Power Supply

    E-Print Network [OSTI]

    Akagi, H

    1999-01-01T23:59:59.000Z

    Power Compensation Effect of an Adjustable-Speed Rotary Condenser with a Flywheel for a Large Capacity Magnet Power Supply

  4. SLAC Next-Generation High Availability Power Supply

    SciTech Connect (OSTI)

    Bellomo, P.; MacNair, D.; /SLAC; ,

    2010-06-11T23:59:59.000Z

    SLAC recently commissioned forty high availability (HA) magnet power supplies for Japan's ATF2 project. SLAC is now developing a next-generation N+1 modular power supply with even better availability and versatility. The goal is to have unipolar and bipolar output capability. It has novel topology and components to achieve very low output voltage to drive superconducting magnets. A redundant, embedded, digital controller in each module provides increased bandwidth for use in beam-based alignment, and orbit correction systems. The controllers have independent inputs for connection to two external control nodes. Under fault conditions, they sense failures and isolate the modules. Power supply speed mitigates the effects of fault transients and obviates subsequent magnet standardization. Hot swap capability promises higher availability and other exciting benefits for future, more complex, accelerators, and eventually the International Linear Collider project.

  5. Continuous Sustainable Power Supply - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power Administration would likeConstitution And Bylaws |ContactFlow Diffusion

  6. POWER SUPPLIES FOR THE BENDING MAGNETS OF THE BEP AND VEPP-2000 STORAGE RING

    E-Print Network [OSTI]

    Kozak, Victor R.

    POWER SUPPLIES FOR THE BENDING MAGNETS OF THE BEP AND VEPP-2000 STORAGE RING S.S. Vasichev, V of the collider. The beam energy change lead to the necessity to develop new power supplies for the main field for the supplies and design of the power part has been revised completely. POWER SUPPLY FOR THE BENDING MAGNETS

  7. Oligopolistic Competition in Power Networks: A Conjectured Supply Function Approach

    E-Print Network [OSTI]

    California at Berkeley. University of

    , CSF equilibria can be cal- culated for large transmission networks. Existence and unique- ness on linearized DC networks based on a flexible repre- sentation of interactions of competing generating firms. WePWP-090 Oligopolistic Competition in Power Networks: A Conjectured Supply Function Approach

  8. Reinforcement Learning Based Dynamic Power Management with a Hybrid Power Supply

    E-Print Network [OSTI]

    Pedram, Massoud

    Reinforcement Learning Based Dynamic Power Management with a Hybrid Power Supply Siyu Yue, Di Zhu management (DPM) in battery- powered mobile systems attempts to achieve higher energy efficiency to a previously reported expert- based learning approach. Keywords-dynamic power management; reinforcement

  9. POWER SUPPLIES FOR THE BENDING MAGNETS OF THE BEP AND VEPP-2000 STORAGE RING

    E-Print Network [OSTI]

    Kozak, Victor R.

    POWER SUPPLIES FOR THE BENDING MAGNETS OF THE BEP AND VEPP-2000 STORAGE RING K.M. Gorchakov, S new complex VEPP-2000. The two new power supply for bending magnet was built for BEP and VEPP-2000 storage ring. POWER SUPPLY FOR THE BENDING MAGNETS OF THE BEP Below are the parameters of the supply (the

  10. Outline Introduction Literature Review Electric Power Supply Chains Empirical Examples Conclusions An Integrated Electric Power Supply Chain and Fuel Market

    E-Print Network [OSTI]

    Nagurney, Anna

    Supply Chains and Fuel Markets In the U.S., electric power generation accounts for 30% of the natural gas demand (over 50% in the summer), 90% of the coal demand, and over 45% of the residual fuel oil demand, the wholesale electricity price in New England decreased by 38% mainly because the delivered natural gas price

  11. Introduction Literature Review Integrated Electric Power Supply Chains Empirical Examples Conclusions An Integrated Electric Power Supply Chain and Fuel

    E-Print Network [OSTI]

    Nagurney, Anna

    50% in the summer) 90% of the coal demand over 45% of the residual fuel oil demand. #12;Introduction, the wholesale electricity price in New England decreased by 38% mainly because the delivered natural gas priceIntroduction Literature Review Integrated Electric Power Supply Chains Empirical Examples

  12. Carbon-based Materials for Energy Storage

    E-Print Network [OSTI]

    Rice, Lynn Margaret

    2012-01-01T23:59:59.000Z

    electric vehicles 5 , uninterruptable power supply systems (electric vehicles 1-1 to uninterruptable power supply systems (

  13. Optimal Power Cost Management Using Stored Energy in Data Centers

    E-Print Network [OSTI]

    Giles, C. Lee

    Optimal Power Cost Management Using Stored Energy in Data Centers Rahul Urgaonkar, Bhuvan Urgaonkar of uninterrupted power supply (UPS) units as energy storage devices. This rep- resents a deviation from the usual average electric utility bill in a data center. Us- ing the technique of Lyapunov optimization, we develop

  14. Optimal Power Cost Management Using Stored Energy in Data Centers

    E-Print Network [OSTI]

    Urgaonkar, Bhuvan

    the aver- age price of 1 MW-Hour of electricity. Consequently, mini- mization of energy consumption needOptimal Power Cost Management Using Stored Energy in Data Centers Rahul Urgaonkar, Bhuvan Urgaonkar that arise by the use of uninterrupted power supply (UPS) units as energy storage devices. This rep- resents

  15. CONTROL SYSTEM FOR MAGNET POWER SUPPLIES FOR NOVOSIBIRSK FREE ELECTRON LASER

    E-Print Network [OSTI]

    Kozak, Victor R.

    CONTROL SYSTEM FOR MAGNET POWER SUPPLIES FOR NOVOSIBIRSK FREE ELECTRON LASER Yu.M.Velikanov, V, the software tools for power supply diagnostics are described. INTRODUCTION A high-power free electron laser electron laser (FEL) is described. The characteristics and structure of the power supply system

  16. 275 C Downhole Switched-Mode Power Supply

    SciTech Connect (OSTI)

    Chris Hutchens; Vijay Madhuravasal

    2008-08-31T23:59:59.000Z

    A vee-square (V2) control based controller IC is developed for a switch mode power supply capable of operating at extreme temperature/harsh environment conditions. A buck type regulator with silicon carbide power junction field effect transistors (JFET) as power devices is used to analyze the performance of controller. Special emphases are made on the analog sub-blocks--voltage reference, operational transconductance amplifier and comparator as individual building blocks. Transformer coupled gate drives and high temperature operable magnetic cores and capacitors are identified and tested for use in the design. Conventional ceramic chip packaging of ICs combined with lead carrier type mounting of passive filter components is introduced for hybrid packaging of the complete product. The developed SMPS is anticipated to support the operation of down-hole microcontrollers and other electronics devices that require low/medium power filtered dc inputs over an operating temperature of 275 C.

  17. Power supply partitioning for placement of built-in current sensors for IDDQ testing

    E-Print Network [OSTI]

    Prasad, Abhijit

    2004-09-30T23:59:59.000Z

    using IDDQ testing. Power supply partitioning has been proposed to increase test resolution by partitioning the power supply network, such that each partition has a relatively small defect-free IDDQ level. However, at present no practical partitioning...

  18. DC switching regulated power supply for driving an inductive load

    DOE Patents [OSTI]

    Dyer, G.R.

    1983-11-29T23:59:59.000Z

    A dc switching regulated power supply for driving an inductive load is provided. The regulator basic circuit is a bridge arrangement of diodes and transistors. First and second opposite legs of the bridge are formed by first and second parallel-connected transistor arrays, respectively, while the third and fourth legs of the bridge are formed by appropriately connected first and second parallel connected diode arrays, respectively. A dc power supply is connected to the input of the bridge and the output is connected to the load. A servo controller is provided to control the switching rate of the transistors to maintain a desired current to the load. The regulator may be operated in three stages or modes: (1) for current runup in the load, both first and second transistor switch arrays are turned on and current is supplied to the load through both transistor arrays. (2) When load current reaches the desired level, the first switch is turned off, and load current flywheels through the second switch array and the fourth leg diode array connecting the second switch array in series with the load. Current is maintained by alternating between modes 1 and 2 at a suitable duty cycle and switching rate set by the controller. (3) Rapid current rundown is accomplished by turning both switch arrays off, allowing load current to be dumped back into the source through the third and fourth diode arrays connecting the source in series opposition with the load to recover energy from the inductive load.

  19. DC switching regulated power supply for driving an inductive load

    DOE Patents [OSTI]

    Dyer, George R. (Norris, TN)

    1986-01-01T23:59:59.000Z

    A power supply for driving an inductive load current from a dc power supply hrough a regulator circuit including a bridge arrangement of diodes and switching transistors controlled by a servo controller which regulates switching in response to the load current to maintain a selected load current. First and second opposite legs of the bridge are formed by first and second parallel-connected transistor arrays, respectively, while the third and fourth legs of the bridge are formed by appropriately connected first and second parallel connected diode arrays, respectively. The regulator may be operated in three "stages" or modes: (1) For current runup in the load, both first and second transistor switch arrays are turned "on" and current is supplied to the load through both transistor arrays. (2) When load current reaches the desired level, the first switch is turned "off", and load current "flywheels" through the second switch array and the fourth leg diode array connecting the second switch array in series with the load. Current is maintained by alternating between modes 1 and 2 at a suitable duty cycle and switching rate set by the controller. (3) Rapid current rundown is accomplished by turning both switch arrays "off", allowing load current to be dumped back into the source through the third and fourth diode arrays connecting the source in series opposition with the load to recover energy from the inductive load. The three operating states are controlled automatically by the controller.

  20. Development of 13-V, 5000-A DC Power Supply with High-Frequency Transformer Coupling

    E-Print Network [OSTI]

    Fujimoto, Hiroshi

    -voltage and large-current DC power supply with a high-frequency transformer coupling, which is applied to electric. Keywords-DC power supply; low-voltage and large-current; high-frequency transformer; Schottky diodeDevelopment of 13-V, 5000-A DC Power Supply with High-Frequency Transformer Coupling Applied

  1. Assessment of the Economic Potential of Microgrids for Reactive Power Supply

    E-Print Network [OSTI]

    Appen, Jan von

    2012-01-01T23:59:59.000Z

    Reactive Power from Distributed Energy”, The Electricityvoltage. Electricity consumers’ demand for reactive power ison electricity supply security, the costs of local reactive

  2. Klystron switching power supplies for the Internation Linear Collider

    SciTech Connect (OSTI)

    Fraioli, Andrea; /Cassino U. /INFN, Pisa

    2009-12-01T23:59:59.000Z

    The International Linear Collider is a majestic High Energy Physics particle accelerator that will give physicists a new cosmic doorway to explore energy regimes beyond the reach of today's accelerators. ILC will complement the Large Hadron Collider (LHC), a proton-proton collider at the European Center for Nuclear Research (CERN) in Geneva, Switzerland, by producing electron-positron collisions at center of mass energy of about 500 GeV. In particular, the subject of this dissertation is the R&D for a solid state Marx Modulator and relative switching power supply for the International Linear Collider Main LINAC Radio Frequency stations.

  3. Hefei Sungrow Power Supply Co Ltd SPS | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual Siteof Energy 2,AUDIT REPORTEnergyFarms AHefei Sungrow Power Supply Co Ltd SPS Jump to:

  4. Hefei Sunlight Power Supply Co Ltd | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual Siteof Energy 2,AUDIT REPORTEnergyFarms AHefei Sungrow Power Supply Co Ltd SPS Jump

  5. Booster main magnet power supply, present operation and potential future upgrades

    SciTech Connect (OSTI)

    Bajon, E.; Bannon, M.; Marneris, I.; Danowski, G.; Sandberg, J.; Savatteri, S.

    2011-03-28T23:59:59.000Z

    The Brookhaven Booster Main Magnet Power Supply (MMPS) is a 24 pulse thyristor control supply, rated at 5500 Amps, +/-2000 Volts, or 3000 Amps, +/-6000 Volts. The power supply is fed directly from the power utility and the peak magnet power is 18 MWatts. This peak power is seen directly at the incoming ac line. This power supply has been in operation for the last 18 years. This paper will describe the present topology and operation of the power supply, the feedback control system and the different modes of operation of the power supply. Since the power supply has been in operation for the last 18 years, upgrading this power supply is essential. A new power supply topology has been studied where energy is stored in capacitor banks. DC to DC converters are used to convert the dc voltage stored in the capacitor banks to pulsed DC voltage into the magnet load. This enables the average incoming power from the ac line to be constant while the peak magnet power is pulsed to +/- 18 MWatts. Simulations and waveforms of this power supply will be presented.

  6. IEEE Network September/October 20112 0890-8044/11/$25.00 2011 IEEE he smart power grid uses information and communica-

    E-Print Network [OSTI]

    Koutsopoulos, Iordanis

    and operator premises over the Internet through an RF, wireline or power- line communication infrastructure devices (e.g., uninterrupted power supply, UPS), and plug-in hybrid electric vehicles (PHEVsIEEE Network · September/October 20112 0890-8044/11/$25.00 © 2011 IEEE he smart power grid uses

  7. Monitoring apparatus and method for battery power supply

    DOE Patents [OSTI]

    Martin, Harry L. (Knoxville, TN); Goodson, Raymond E. (West Lafayette, IN)

    1983-01-01T23:59:59.000Z

    A monitoring apparatus and method are disclosed for monitoring and/or indicating energy that a battery power source has then remaining and/or can deliver for utilization purposes as, for example, to an electric vehicle. A battery mathematical model forms the basis for monitoring with a capacity prediction determined from measurement of the discharge current rate and stored battery parameters. The predicted capacity is used to provide a state-of-charge indication. Self-calibration over the life of the battery power supply is enacted through use of a feedback voltage based upon the difference between predicted and measured voltages to correct the battery mathematical model. Through use of a microprocessor with central information storage of temperature, current and voltage, system behavior is monitored, and system flexibility is enhanced.

  8. High voltage power supply with modular series resonant inverters

    DOE Patents [OSTI]

    Dreifuerst, G.R.; Merritt, B.T.

    1995-07-18T23:59:59.000Z

    A relatively small and compact high voltage, high current power supply for a laser utilizes a plurality of modules containing series resonant half bridge inverters. A pair of reverse conducting thyristors are incorporated in each series resonant inverter module such that the series resonant inverter modules are sequentially activated in phases 360{degree}/n apart, where n=number of modules for n>2. Selective activation of the modules allows precise output control reducing ripple and improving efficiency. Each series resonant half bridge inverter module includes a transformer which has a cooling manifold for actively circulating a coolant such as water, to cool the transformer core as well as selected circuit elements. Conductors connecting and forming various circuit components comprise hollow, electrically conductive tubes such as copper. Coolant circulates through the tubes to remove heat. The conductive tubes act as electrically conductive lines for connecting various components of the power supply. Where it is desired to make electrical isolation breaks, tubes comprised of insulating material such as nylon are used to provide insulation and continue the fluid circuit. 11 figs.

  9. High voltage power supply with modular series resonant inverters

    DOE Patents [OSTI]

    Dreifuerst, Gary R. (Livermore, CA); Merritt, Bernard T. (Livermore, CA)

    1995-01-01T23:59:59.000Z

    A relatively small and compact high voltage, high current power supply for a laser utilizes a plurality of modules containing series resonant half bridge inverters. A pair of reverse conducting thyristors are incorporated in each series resonant inverter module such that the series resonant inverter modules are sequentially activated in phases 360.degree./n apart, where n=number of modules for n>2. Selective activation of the modules allows precise output control reducing ripple and improving efficiency. Each series resonant half bridge inverter module includes a transformer which has a cooling manifold for actively circulating a coolant such as water, to cool the transformer core as well as selected circuit elements. Conductors connecting and forming various circuit components comprise hollow, electrically conductive tubes such as copper. Coolant circulates through the tubes to remove heat. The conductive tubes act as electrically conductive lines for connecting various components of the power supply. Where it is desired to make electrical isolation breaks, tubes comprised of insulating material such as nylon are used to provide insulation and continue the fluid circuit.

  10. THE POWER SUPPLY SYSTEM FOR THE ACCELERATING COLUMN OF THE 2 MEV ELECTRON COOLER FOR COSY

    E-Print Network [OSTI]

    Kozak, Victor R.

    a high-energy electron beam. The power supply for the accelerating column of the electron cooling systemTHE POWER SUPPLY SYSTEM FOR THE ACCELERATING COLUMN OF THE 2 MEV ELECTRON COOLER FOR COSY D controlled voltage source for 60 kV, 1mA and an additional supply for the solenoids of the magnetic system

  11. HypoEnergy: Hybrid supercapacitor-battery power-supply optimization for Energy efficiency

    E-Print Network [OSTI]

    HypoEnergy: Hybrid supercapacitor-battery power-supply optimization for Energy efficiency Azalia the hybrid battery-supercapacitor power supply life- time. HypoEnergy combines high energy density and supercapacitors' charging overhead. HypoEnergy-KI studies the hybrid supply lifetime optimization

  12. CapLibrate: Self-Calibration of an Energy Harvesting Power Supply with Supercapacitors

    E-Print Network [OSTI]

    Turau, Volker

    CapLibrate: Self-Calibration of an Energy Harvesting Power Supply with Supercapacitors Christian and assess models for a supercapacitor- based harvesting supply. The parameters of the models are discussed

  13. Low Cost Power and Supply Noise Estimation and Control in Scan Testing of VLSI Circuits

    E-Print Network [OSTI]

    Jiang, Zhongwei

    2012-02-14T23:59:59.000Z

    Test power is an important issue in deep submicron semiconductor testing. Too much power supply noise and too much power dissipation can result in excessive temperature rise, both leading to overkill during delay test. Scan-based test has been...

  14. A SCR SWITCHED CAPACITOR VOLTAGE REGULATOR FOR 150 kV NEUTRAL BEAM POWER SUPPLY

    E-Print Network [OSTI]

    Milnes, K.A.

    2011-01-01T23:59:59.000Z

    et a1. , "150-kV, 80-A Solid State Power Supply for Neutral100% solid state and provides 1% regulation at power levelssolid state high voltage re- gulator. The block diagram of the power

  15. Pulsed power supply for three APS septum magnets

    SciTech Connect (OSTI)

    McGhee, D.G.

    1991-03-24T23:59:59.000Z

    Three septum magnets will be operated at a repetition-rate of 2 Hz. Two of the septum magnets are identical and operate at the same values; these are the synchrotron extraction and the storage ring injection magnets. They are transformer septum magnets, with a primary inductance of 23 {mu}H and resistance of 6.3 m{Omega}, and must be pulsed at a 2 Hz rate to extract beam from the synchrotron and inject beam into the storage ring at 7.7 GeV. The third septum magnet is used to inject electrons into the synchrotron at 650 MeV or positrons at 450 MeV. It is also a transformer septum magnet, with a primary inductance of 21 {mu}H and resistance of 6.7 m{Omega}, and must be pulsed at a 2 Hz rate. A design study was performed of the power supply proposed in the APS Title I design. This supply produces a pulse that is approximately a half-sine-wave with a base width of approximately 1/3 ms; its peakcurrent is adjustable from 470 A to 4.7 kA and is repeatable within {plus_minus}0.05%. The septum steel is reset by a half-sine pulse of reverse polarity a few milliseconds after the forward current pulse. No beam is present during reset. The use of the transformer design minimizes the cost of the capacitors used for energy storage.

  16. Remote Area Power Supply (RAPS) load and resource profiles.

    SciTech Connect (OSTI)

    Giles, Lauren (Energetics, Inc., Washington, DC); Skolnik, Edward G. (Energetics, Inc., Washington, DC); Marchionini, Brian (Energetics, Inc., Washington, DC); Fall, Ndeye K. (Energetics, Inc., Washington, DC)

    2007-07-01T23:59:59.000Z

    In 1997, an international team interested in the development of Remote Area Power Supply (RAPS) systems for rural electrification projects around the world was organized by the International Lead Zinc Research Organization (ILZRO) with the support of Sandia National Laboratories (SNL). The team focused on defining load and resource profiles for RAPS systems. They identified single family homes, small communities, and villages as candidates for RAPS applications, and defined several different size/power requirements for each. Based on renewable energy and resource data, the team devised a ''strawman'' series of load profiles. A RAPS system typically consists of a renewable and/or conventional generator, power conversion equipment, and a battery. The purpose of this report is to present data and information on insolation levels and load requirements for ''typical'' homes, small communities, and larger villages around the world in order to facilitate the development of robust design practices for RAPS systems, and especially for the storage battery component. These systems could have significant impact on areas of the world that would otherwise not be served by conventional electrical grids.

  17. 2014-10-02 Issuance: Energy Conservation Program: Test Procedures for External Power Supplies, Notice of Proposed Rulemaking

    Broader source: Energy.gov [DOE]

    Energy Conservation Program: Test Procedures for External Power Supplies, Notice of Proposed Rulemaking

  18. DECENTRALIZED REAL-TIME MANAGEMENT LARGELY UNPREDICTABLE POWER NEEDS AND SUPPLY

    E-Print Network [OSTI]

    Wedde, Horst F.

    of unpredictable power need and supply situations. We model a representative scenario to explain variousDECENTRALIZED REAL-TIME MANAGEMENT OF LARGELY UNPREDICTABLE POWER NEEDS AND SUPPLY H. F. Wedde*, F technologies based on solar or wind power, or on renewable energy sources, is an adequate management

  19. RESONANT TRANSITION SWITCHING WELDING POWER SUPPLY N. Frohleke, H. Mundinger, S. Beineke, P. Wallmeier, H. Grotstollen

    E-Print Network [OSTI]

    Paderborn, Universität

    RESONANT TRANSITION SWITCHING WELDING POWER SUPPLY N. Frohleke, H. Mundinger, S. Beineke, P-bridge topology used in a welding power supply. A new driving scheme adapts the resulting power circuitry for both the droplet and the short-circuiting transfer welding modes occurring in the gas metal arc welding process

  20. Dynamic Electric Power Supply Chains and Transportation Networks: An Evolutionary Variational Inequality Formulation

    E-Print Network [OSTI]

    Nagurney, Anna

    Dynamic Electric Power Supply Chains and Transportation Networks: An Evolutionary Variational; Transportation Research E 43 (2007) pp 624-646. 1 #12;Abstract: In this paper, we develop a static electric power supernetwork. This equivalence yields a new interpretation of electric power supply chain network equilibria

  1. EXPERIMENT E951 POWER SUPPLY TO PULSE A 14.5 TESLA SOLENOID MAGNET

    E-Print Network [OSTI]

    McDonald, Kirk

    .1 15.2 Cases 2 and 3 require the same power supply, but differ in the magnet cooling scheme. #12;0 4 8EXPERIMENT E951 POWER SUPPLY TO PULSE A 14.5 TESLA SOLENOID MAGNET IOANNIS MARNERIS BOOSTER supply. #12;0 4 8 12 16 20 24 28 32 36 40 0 2 4 6 8 10 -500 -400 -300 -200 -100 0 100 200 300 400 500

  2. INTEGRATED MICRO FUEL CELL POWER SUPPLY Andr D. Taylor and Levi T. Thompson

    E-Print Network [OSTI]

    Haller, Gary L.

    . Microfabricated micro-fuel cells hold promise for being highly efficient with low cost. Several approaches haveINTEGRATED MICRO FUEL CELL POWER SUPPLY André D. Taylor and Levi T. Thompson University of Michigan Ann Arbor, Michigan 48109-2136 ABSTRACT An integrated thin film micro fuel cell power supply design

  3. Supplying Baseload Power and Reducing Transmission Requirements by Interconnecting Wind Farms

    E-Print Network [OSTI]

    Supplying Baseload Power and Reducing Transmission Requirements by Interconnecting Wind Farms is not used to supply baseload electric power today. Interconnecting wind farms through the transmission grid farms are interconnected in an array, wind speed correlation among sites decreases and so does

  4. Design of a Control Strategy for a Fuel Cell/Battery Hybrid Power Supply 

    E-Print Network [OSTI]

    Smith, Richard C.

    2010-01-14T23:59:59.000Z

    The purpose of this thesis is to design hardware and a control strategy for a fuel cell/battery hybrid power supply. Modern fuel cell/battery hybrid power supplies can have 2 DC/DC converters: one converter for the battery ...

  5. Design of a Free Piston Pneumatic Compressor as a Mobile Robot Power Supply

    E-Print Network [OSTI]

    Barth, Eric J.

    Design of a Free Piston Pneumatic Compressor as a Mobile Robot Power Supply Jose A. Riofrio.j.barth@vanderbilt.edu Abstract ­ The design of a free piston compressor (FPC) intended as a pneumatic power supply is achieved by matching the dynamic load of the compressor to the ideal adiabatic expansion of the hot gas

  6. Design of a Control Strategy for a Fuel Cell/Battery Hybrid Power Supply

    E-Print Network [OSTI]

    Smith, Richard C.

    2010-01-14T23:59:59.000Z

    The purpose of this thesis is to design hardware and a control strategy for a fuel cell/battery hybrid power supply. Modern fuel cell/battery hybrid power supplies can have 2 DC/DC converters: one converter for the battery and one for the fuel cell...

  7. TurboCap: A Batteryless, Supercapacitor-based Power Supply for Mini-FDPM

    E-Print Network [OSTI]

    Shinozuka, Masanobu

    TurboCap: A Batteryless, Supercapacitor-based Power Supply for Mini-FDPM Chulsung Park1 , KeunsikCap, a batteryless, supercapacitor-based power supply subsystem for a handheld, laser-based breast cancer detector on the selection of supercapacitor topology for conversion efficiency and for form- factor minimization

  8. The Combined Effect of Process Variations and Power Supply Noise on Clock Skew and Jitter

    E-Print Network [OSTI]

    De Micheli, Giovanni

    The Combined Effect of Process Variations and Power Supply Noise on Clock Skew and Jitter Hu Xu and power supply noise on clock skew and jitter is investigated in this paper. A statistical model of skitter, which consists of skew and jitter, is proposed. Clock paths with different buffer insertion

  9. Simulating calculations and optimization design of a new HVDC supply power for light rail system

    E-Print Network [OSTI]

    Boyer, Edmond

    Simulating calculations and optimization design of a new HVDC supply power for light rail system-In this paper, a new HVDC power supply system for light rail systems is presented and compared to classical such a complex system, taking into account vehicle motion and HVDC electrical distribution. Then, an optimization

  10. USING WEIGHTED SUM METHOD FOR THE CHOICE OF THE NIGHT VISION GOGGLES BATTERY POWER SUPPLY

    E-Print Network [OSTI]

    Mustakerov, Ivan

    electrical battery power supply lifetime, pric and weight. © ~1mKeHepllH llayKH, rOA. XUV, 2007,.N'] I into account device working range, weight and price and also electrical battery power supply lifetime, temperature working range and its mechanics. The multicriteria optimization choice of the electrical battery

  11. Load controller and method to enhance effective capacity of a photovoltaic power supply

    DOE Patents [OSTI]

    Perez, Richard (Delmar, NY)

    2000-01-01T23:59:59.000Z

    A load controller and method are provided for maximizing effective capacity of a non-controllable, renewable power supply coupled to a variable electrical load also coupled to a conventional power grid. Effective capacity is enhanced by monitoring power output of the renewable supply and loading, and comparing the loading against the power output and a load adjustment threshold determined from an expected peak loading. A value for a load adjustment parameter is calculated by subtracting the renewable supply output and the load adjustment parameter from the current load. This value is then employed to control the variable load in an amount proportional to the value of the load control parameter when the parameter is within a predefined range. By so controlling the load, the effective capacity of the non-controllable, renewable power supply is increased without any attempt at operational feedback control of the renewable supply. The renewable supply may comprise, for example, a photovoltaic power supply or a wind-based power supply.

  12. Reinforcement Learning-Based Dynamic Power Management of a Battery-Powered System Supplying Multiple Active Modes

    E-Print Network [OSTI]

    Pedram, Massoud

    Reinforcement Learning-Based Dynamic Power Management of a Battery-Powered System Supplying dynamic power management (DPM) framework is based on model-free reinforcement learning (RL) technique. In this DPM framework, the Power Manager (PM) adapts the system operating mode to the actual battery state

  13. CONTINUOUS POWER SUPPLY FOR ROBOT COLONY GARY PARKER, CONNECTICUT COLLEGE, USA, parker@conncoll.edu

    E-Print Network [OSTI]

    Parker, Gary B.

    power good because does require a specific spot charging, does require large surface solar panels, the robot to recharge from solar panels about hours sunlight. Solar panels alone have enough power supply hold enough power quickly charged. Charging can take place using solar power a charging station. Solar

  14. Dynamics of Electric Power Supply Chain Networks under Risk and Uncertainty

    E-Print Network [OSTI]

    Nagurney, Anna

    power industry in the US and in several other countries has been undergoing a fundamental transformation multicriteria decision-makers, who operate in a decentralized manner and include power generators, power time. Keywords: Electric power; Supply chains; Networks; Multicriteria optimization; Projected dynam

  15. Power Utility Maximization for Multiple-Supply Systems by a Load-Matching Switch

    E-Print Network [OSTI]

    Shinozuka, Masanobu

    Power Utility Maximization for Multiple-Supply Systems by a Load-Matching Switch Chulsung Park {chulsung,phchou}@uci.edu ABSTRACT For embedded systems that rely on multiple power sources (MPS), power systems General Terms Design, experimentation Keywords Solar energy, photovoltaics, power model, solar

  16. Reliability of the generation supply in an interconnected power system

    E-Print Network [OSTI]

    Holditch, Damon Will

    1967-01-01T23:59:59.000Z

    method of calculating generation supply reliability was first described by Calabrese. This method has been expanded and refined by numerous other authors. The reliability figure of meri. t usually calculated using Calabrese's method is called loss...

  17. A preliminary investigation of the Topaz II reactor as a lunar surface power supply

    SciTech Connect (OSTI)

    Polansky, G.F. [Sandia National Labs., Albuquerque, NM (United States); Houts, M.G. [Los Alamos National Lab., NM (United States)

    1995-12-31T23:59:59.000Z

    Reactor power supplies offer many attractive characteristics for lunar surface applications. The Topaz II reactor resulted from an extensive development program in the former Soviet Union. Flight quality reactor units remain from this program and are currently under evaluation in the United States. This paper examines the potential for applying the Topaz II, originally developed to provide spacecraft power, as a lunar surface power supply.

  18. Electric power supply and demand for the contiguous United States, 1980-1989

    SciTech Connect (OSTI)

    None

    1980-06-01T23:59:59.000Z

    A limited review is presented of the outlook for the electric power supply and demand during the period 1980 to 1989. Only the adequacy and reliability aspects of bulk electric power supply in the contiguous US are considered. The economic, financial and environmental aspects of electric power system planning and the distribution of electricity (below the transmission level) are topics of prime importance, but they are outside the scope of this report.

  19. Power Supply Status Quotes received for Op Amps 20 Op amps will be purchased (2 spares). 21 week

    E-Print Network [OSTI]

    McDonald, Kirk

    Power Supply Status Quotes received for Op Amps ­ 20 Op amps will be purchased (2 spares). 21 week system for use in power supply control system. ­ Evidently they are the same. Cryo Foam/Insulation Status

  20. An Efficient Supply Modulator for Linear Wideband RF Power Amplifiers

    E-Print Network [OSTI]

    Turkson, Richard

    2011-10-21T23:59:59.000Z

    by ???? ,?? = ???(???? ) +? ?? . ? ??? ????? (2.3) where Pdc(Pout) is the dc power used at Pout and p Pdc is the probability of consuming Power, Pdc, when transmitting Pout. If the dc power consumed by the PA is constant (i.e. independent of the power transmitted) then, Pdc Pout =Pdc... operating conditions then p Pdc =p(Pout) and the average dc power dissipated by the PA becomes ???? ,?? = ???(???? ) +? ?? . ? ???? ????? (2.5) This is what we seek...

  1. Development of Low-Voltage and Large-Current DC Power Supply with High-Frequency Transformer Coupling

    E-Print Network [OSTI]

    Fujimoto, Hiroshi

    Development of Low-Voltage and Large-Current DC Power Supply with High-Frequency Transformer-voltage and large-current DC power supply with a high-frequency transformer coupling. The power supply is simply·,Zü"gg"X·C~R,êC"_N^"X Keywords: DC power supply, low-voltage and large-current, high-frequency transformer, leakage inductance 1

  2. 130kV 130A High Voltage Switching Mode Power Supply for Neutral Injections – Control Issues and Algorithms

    E-Print Network [OSTI]

    130kV 130A High Voltage Switching Mode Power Supply for Neutral Injections – Control Issues and Algorithms

  3. Development of Low-Voltage and Large Current DC Power Supply with High-Frequency Transformer Coupling

    E-Print Network [OSTI]

    Fujimoto, Hiroshi

    Development of Low-Voltage and Large Current DC Power Supply with High-Frequency Transformer excellent performance. Keywords DC power supply, low-voltage and large-current, high-frequency transformer Iobe (MACOHO Co., Ltd.) Abstract This paper describes low-voltage and large-current DC power supplies

  4. Ver.2003.01.27 Development of Low-Voltage and Large-Current DC Power Supply

    E-Print Network [OSTI]

    Fujimoto, Hiroshi

    describes low-voltage and large-current DC power supplies with a high-frequency transformer coupling. Two Ver.2003.01.27 Development of Low-Voltage and Large-Current DC Power Supply-bridge inverter, an amorphous-core step down transformer and a schottky diode rectifier. One power supply operates

  5. An Integrated Electric Power Supply Chain and Fuel Market Network Framework: Theoretical Modeling with Empirical Analysis for New England

    E-Print Network [OSTI]

    Nagurney, Anna

    a critical infrastructure for the functioning of our modern economies and societies. Electric power lightsAn Integrated Electric Power Supply Chain and Fuel Market Network Framework: Theoretical Modeling Abstract: In this paper, we develop a novel electric power supply chain network model with fuel supply

  6. Low-Volume Power Supply for Vehicular Fuel Injection Systems

    E-Print Network [OSTI]

    Prodiæ, Aleksandar

    of these needles is controlled by solenoids requiring higher than the automobile battery supply voltage drives. Solenoid fuel injectors will expose the injector driver to a pulsating inductive load current amount of charge in a short period of time in the form of a particular output current waveform [4

  7. Bottom-Up Self-Organization of Unpredictable Demand and Supply under Decentralized Power Management

    E-Print Network [OSTI]

    Wedde, Horst F.

    level of granularity, with short-term power balance fluctuation, in terms of a peak demand and supply, distributed power production at lower voltage levels (through wind turbines or solar panels) is considered, as this depends on external environmental conditions (e.g. solar and wind power). In Electrical Engineering

  8. Controlled Use of a Robot Colony Power Supply Gary B. Parker

    E-Print Network [OSTI]

    Parker, Gary B.

    recharge and release power more quickly. Two forms of charging are solar panels and a continuous power station. Brooks used a robot, Attila, which had batteries and recharged with solar panels [4]. This system controller was implemented to direct the hexapod colony robot behavior according to its power supply status

  9. Power Supplies for TESLA Modulators Hans-Jrg Eckoldt, Niels Heidbrook

    E-Print Network [OSTI]

    ...................................................................................11 5.4.1 SCR bridge with single phase control..................................................................12 5.4.2 SCR bridge with sequential phase control, a semiconductor switch, the pulse transformer, the bouncer circuit and the HV power supply. For safety reasons

  10. Assessment of the Economic Potential of Microgrids for Reactive Power Supply

    E-Print Network [OSTI]

    Appen, Jan von

    2012-01-01T23:59:59.000Z

    Power supplied by PV Inverters – Cost-Benefit-Analysis,” 22over-sizing an inverter for 100 kW PV system by 5 percentlike PV typically produce DC, and use inverters to connect

  11. E-Print Network 3.0 - autonomous power-supply systems Sample...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    telescope Summary: covering the 0-2000 V range (two external HV power supplies). The Cooling system is water based... below: 1. RS-232. Remote control of the High Voltage...

  12. The creation of fiberglass tanks and parts for autonomous underwater vehicle constant buoyancy power supply

    E-Print Network [OSTI]

    Sack, Jean H. (Jean Hope)

    2013-01-01T23:59:59.000Z

    The purpose of this thesis was to construct and seal air and containment tanks and other parts for a constant buoyancy power supply for an Autonomous Underwater Vehicle, or AUV. While multiple materials and techniques were ...

  13. Trends in Gulf Coast Power Supply, Demand, and Costs

    E-Print Network [OSTI]

    Posey, L. G., Jr.

    1980-01-01T23:59:59.000Z

    During the 1980s, both the cost and availability of industrial electric power will become critical to corporations contemplating expansions and new sites along the Gulf Coast. Fuel costs have grown rapidly, and the shift to coal and nuclear power...

  14. Jan/Feb 2001 1 Supply 500 W for your Class-E power amplifier

    E-Print Network [OSTI]

    an isolation transformer, a variable au- totransformer and a large choke (see Note 5). Recently, switchingJan/Feb 2001 1 Supply 500 W for your Class-E power amplifier with a compact switcher that costs.F.Davis@jpl.nasa.gov Dragan Maric, DMARIC1@irf.com Kent Potter, KC6OKH, c/o David Rutledge A Keyed Power Supply for Class

  15. Magnet power supply control of the NSLS VUV and x-ray storage rings transfer lines

    SciTech Connect (OSTI)

    Klein, J.D.; Ramamoorthy, S.; Singh, O.; Smith, J.D.

    1985-01-01T23:59:59.000Z

    The transfer lines for NSLS VUV and x-ray storage rings have been split. New power supplies have been incorporated with existing ones. The existing microprocessor system has been upgraded in order to control the additional functions. This system expands the input/output port of the microprocessor to an addressable serial/parallel link to each magnet power supply. The implementation of this system will be discussed.

  16. Real-Time Pricing- A Flexible Alternative for Electrical Power Supply

    E-Print Network [OSTI]

    Reynolds, S. D.; Frye, A. O. Jr.

    REAL-TIME PRICING - A FLEXIBLE ALTERNATIVE ..OR ELECTRICAL POWER SUPPLY S. D. REYNOLDS Manager of Industrial Marketing & Services Tennessee Valley Authority Chattanooga, Tennessee ABSTRACT In an increasingly competitive operating... conditions to more tl,an 240 mills per kilo,~atthollr 78 REAL-TIME PRICING A FLEXIBLE ALTERNATIVE rOR ELECTRICAL POWER SUPPLY S. D. REYNOLDS Manager of Industrial Marketing & Services Tennessee Valley Authority Chattanooga, Tennessee ABSTRACT...

  17. The 100,000 amp dc power supply for a staged hadron collider superferric magnet

    SciTech Connect (OSTI)

    Hays, Steven L.; Claypool, Bradley; Foster, G.William; /Fermilab

    2005-09-01T23:59:59.000Z

    A 1.5 volt 100,000 amp DC switcher power supply was developed for testing a superferric magnet string at FNAL. This supply was used during testing as both the ramping supply and holding supply powering a single magnet load with a total load resistance of 0.7{micro} Ohms. The supply consists of ten paralleled switcher cells, powered by a 400 volt/600 Amp DC power supply. Each cell consists of an IGBT H-bridge driving a step-down transformer at a switching frequency of 2 kHz. The transformer has an effective turns ratio of 224:1. The secondary consists of 32 parallel single-turn full wave rectifier windings. The rectification is done with 64 Shottky diodes. Each cell is rated at 1.5 volts/10,000 amps. During this test each cell was operated as a constant power source without load current or field feedback. This paper will describe the design of the switcher cell and control system used during testing. We will also describe the next level of improvements to the current feedback system to improve the ramp control.

  18. Electric vehicle system for charging and supplying electrical power

    DOE Patents [OSTI]

    Su, Gui Jia

    2010-06-08T23:59:59.000Z

    A power system that provides power between an energy storage device, an external charging-source/load, an onboard electrical power generator, and a vehicle drive shaft. The power system has at least one energy storage device electrically connected across a dc bus, at least one filter capacitor leg having at least one filter capacitor electrically connected across the dc bus, at least one power inverter/converter electrically connected across the dc bus, and at least one multiphase motor/generator having stator windings electrically connected at one end to form a neutral point and electrically connected on the other end to one of the power inverter/converters. A charging-sourcing selection socket is electrically connected to the neutral points and the external charging-source/load. At least one electronics controller is electrically connected to the charging-sourcing selection socket and at least one power inverter/converter. The switch legs in each of the inverter/converters selected by the charging-source/load socket collectively function as a single switch leg. The motor/generators function as an inductor.

  19. Trends in Gulf Coast Power Supply, Demand, and Costs 

    E-Print Network [OSTI]

    Posey, L. G., Jr.

    1980-01-01T23:59:59.000Z

    rate' ? Granting industrial rate increases above cost-o" service level ' ? Delays in granting rate increases. For each utility company, we examine past history a assess the regulatory climate to predict the likely effect these issues. Power...

  20. Power Supply Optimization in Sub-130 nm Leakage Dominant Technologies Man L Mui Kaustav Banerjee Amit Mehrotra

    E-Print Network [OSTI]

    Power Supply Optimization in Sub-130 nm Leakage Dominant Technologies Man L Mui Kaustav Banerjee a methodology for systematically optimizing the power supply voltage for maximizing the performance of VLSI cir- cuits in technologies where leakage power is not an insignificant fraction of the total power

  1. First Prev Next Last Go Back Full Screen Close Quit DYNAMICS OF ELECTRIC POWER SUPPLY

    E-Print Network [OSTI]

    Nagurney, Anna

    ·First ·Prev ·Next ·Last ·Go Back ·Full Screen ·Close ·Quit DYNAMICS OF ELECTRIC POWER SUPPLY CHAIN ·Next ·Last ·Go Back ·Full Screen ·Close ·Quit Motivation · The transformation of the electric power electric utility generat- ing capacity had been sold or transferred to unregulated companies - In the US

  2. High-efficiency power supplies for home computers and servers Google Inc. ~ September 2006

    E-Print Network [OSTI]

    Tomkins, Andrew

    , the computer you're using wastes 30-40% of the electrical power it consumes because it is using an inefficient the energy losses by a factor of four. We believe this energy-saving power supply technology can be applied, or more than $5 billion at California's energy rates. The technical changes we propose are very small

  3. On the way to creating a system of distant power supply for space vehicles

    SciTech Connect (OSTI)

    Prisniakov, V.F.; Lyagushin, S.F.; Statsenko, I.N. [Dniepropetrovsk State Univ. (Ukraine)] [Dniepropetrovsk State Univ. (Ukraine); Dranovsky, V.I. [Design Enterprise `Pivdenne`, Dniepropetrovsk (Ukraine)] [Design Enterprise `Pivdenne`, Dniepropetrovsk (Ukraine)

    1996-12-31T23:59:59.000Z

    Solar energy is the most suitable basis for power supply for the majority of projects in the near-Earth space. Passing on to the large-scale space-based systems of power supply requires putting into life demonstration experiments in which power transmission by electromagnetic emission is supposed. In the paper the expedience of developing an autonomous power module which provides the possibility of space programs with great power consumption and wireless transmission system running-up is proved. Ukraine can design a solar power satellite of 10-20kW power on the basis of the research satellite AUOS-SM. Two variants of design solutions for such satellite with solar arrays of great area are presented. Power transmission to the space vehicle-consumer can be conducted by cable as well as in a wireless way. The possibilities of placing microwave and laser energy transmission systems on board the satellite are analysed. It is shown that a power supply system for space vehicles with transmission distance of thousands km can be designed basing on modern lasers. Some experiments making use of great electric power generated by the plant of the satellite under consideration are proposed. The running-up of electric thrusters which are necessary for orientation and distancing is of great interest. Wireless power transmission may be carried on to a small satellite equipped with electric thrusters. 26 refs., 6 figs., 2 tabs.

  4. Efficient On-Chip Power Supply Sampling to Improve Post-Silicon Debug

    E-Print Network [OSTI]

    Murray, Luke

    2014-10-15T23:59:59.000Z

    at points in the power grid that are likely to have problems with droops or spikes; design-time CAD simulations and analysis could be used to identify these potentially problematic locations. Note that these test points may be located at sites... in the power supply. Other approaches required special off-chip equipment, or were destructive in nature. One method used in the past to detect spikes or droops in the power supply has been to look at the effects the noise would have on a circuit. In [2, 3, 4...

  5. Multimegawatt space nuclear power supply, Phase 1 Final report

    SciTech Connect (OSTI)

    Not Available

    1989-02-17T23:59:59.000Z

    This Specification establishes the performance, design, development, and test requirements for the Boeing Multimegawatt Space Nuclear Power System (MSNPS). The Boeing Multimegawatt Space Power System is part of the DOE/SDIO Multimegawatt Space Nuclear Power Program. The purpose of this program is to provide a space-based nuclear power system to meet the needs of SDIO missions. The Boeing MSNPS is a category 1 concept which is capable of delivering 10's of MW(e) for 100's of seconds with effluent permitted. A design goal is for the system to have growth or downscale capability for other power system concepts. The growth objective is to meet the category 3 capability of 100's of MW(e) for 100's of seconds, also with effluent permitted. The purpose of this preliminary document is to guide the conceptual design effort throughout the Phase 1 study effort. This document will be updated through out the study. It will thus result in a record of the development of the design effort.

  6. High voltage power supply. (Latest citations from the US Patent bibliographic file with exemplary claims). Published Search

    SciTech Connect (OSTI)

    NONE

    1996-03-01T23:59:59.000Z

    The bibliography contains citations of selected patents concerning high voltage power supply systems and devices. References describe direct and high current power supplies, microprocessor controlled and programmable systems, amplifiers, power supply stabilization, power circuit protection, feedback control, and pulse modulation. Applications cover laser systems, x-ray tubes, electrophoresis, video apparatus, radar and electronic warfare systems, helmet mounted display, and electrosurgery. (Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

  7. High voltage power supply. (Latest citations from the US Patent bibliographic file with exemplary claims). Published Search

    SciTech Connect (OSTI)

    NONE

    1997-06-01T23:59:59.000Z

    The bibliography contains citations of selected patents concerning high voltage power supply systems and devices. References describe direct and high current power supplies, microprocessor controlled and programmable systems, amplifiers, power supply stabilization, power circuit protection, feedback control, and pulse modulation. Applications cover laser systems, x-ray tubes, electrophoresis, video apparatus, radar and electronic warfare systems, helmet mounted display, and electrosurgery. (Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

  8. A combined compensation method for the output voltage of an insulated core transformer power supply

    SciTech Connect (OSTI)

    Yang, L.; Yang, J., E-mail: jyang@mail.hust.edu.cn; Liu, K. F.; Qin, B.; Chen, D. Z. [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, Wuhan 430074 (China)

    2014-06-15T23:59:59.000Z

    An insulated core transformer (ICT) power supply is an ideal high-voltage generator for irradiation accelerators with energy lower than 3 MeV. However, there is a significant problem that the structure of the segmented cores leads to an increase in the leakage flux and voltage differences between rectifier disks. A high level of consistency in the output of the disks helps to achieve a compact structure by improving the utilization of both the rectifier components and the insulation distances, and consequently increase the output voltage of the power supply. The output voltages of the disks which are far away from the primary coils need to be improved to reduce their inhomogeneity. In this study, by investigating and comparing the existing compensation methods, a new combined compensation method is proposed, which increases the turns on the secondary coils and employs parallel capacitors to improve the consistency of the disks, while covering the entire operating range of the power supply. This method turns out to be both feasible and effective during the development of an ICT power supply. The non-uniformity of the output voltages of the disks is less than 3.5% from no-load to full-load, and the power supply reaches an output specification of 350 kV/60 mA.

  9. Adaptive Tuning of Digitally Controlled Switched Mode Power Supplies

    E-Print Network [OSTI]

    Margin Jeff Morroni, Regan Zane and Dragan Maksimovi Colorado Power Electronics Center University-loop performance or loss of stability in the event of significant operating point changes associated with component and improve dynamic responses and reliability over a wider range of possible operating points. Recent work

  10. Wind power manufacturing and supply chain summit USA.

    SciTech Connect (OSTI)

    Hill, Roger Ray

    2010-12-01T23:59:59.000Z

    The area of wind turbine component manufacturing represents a business opportunity in the wind energy industry. Modern wind turbines can provide large amounts of electricity, cleanly and reliably, at prices competitive with any other new electricity source. Over the next twenty years, the US market for wind power is expected to continue to grow, as is the domestic content of installed turbines, driving demand for American-made components. Between 2005 and 2009, components manufactured domestically grew eight-fold to reach 50 percent of the value of new wind turbines installed in the U.S. in 2009. While that growth is impressive, the industry expects domestic content to continue to grow, creating new opportunities for suppliers. In addition, ever-growing wind power markets around the world provide opportunities for new export markets.

  11. Report on Performance of Prototype Dynatronix Power Supplies Developed Under a Phase I DOE SBIR

    SciTech Connect (OSTI)

    Hoppe, Eric W.; Merriman, Jason H.

    2011-03-01T23:59:59.000Z

    The purpose of this study is to evaluate the prototype power supplies fabricated by Dynatronix, Inc. This project supports the advancement of electroforming capabilities to produce ultra-high purity copper. Ultra-high purity copper is an essential material used for a range of current and future fundamental nuclear physics programs such as the MAJORANA DEMONSTRATOR. The Mach 30 power supplies are a new design built to the specifications from the requirements of Pacific Northwest National Laboratory (PNNL) with regard to timing, voltage, current output, and the required tolerances. The parameters used in these tests were developed empirically over a number of years based on a combination of thermodynamic and kinetics of the electroplating process. The power supplies were operated in a typical cleanroom environment for the production electroforming at PNNL. The units that were received by PNNL in July, 2010 have performed satisfactorily and have demonstrated short term durability.

  12. Electrical Power Supply Applications Engineer | Princeton Plasma Physics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power AdministrationField Campaign:INEAWater Use Goal 4:Administration826Vehicles and

  13. Power Charging and Supply System for Electric Vehicles - Energy Innovation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's Possible forPortsmouth/Paducah Project Office PressPostdoctoraldecadal7PowderPortal Power

  14. Kickers and power supplies for the Fermilab Tevatron I antiproton source

    SciTech Connect (OSTI)

    Castellano, T.; Bartoszek, L.; Tilles, E.; Petter, J.; McCarthy, J.

    1985-05-01T23:59:59.000Z

    The Fermilab Antiproton Source Accumulator and Debuncher rings require 5 kickers in total. These range in design from conventional ferrite delay line type magnets, with ceramic beam tubes to mechanically complex shuttered kickers situated entirely in the Accumulator Ring's 10/sup -10/ torr vacuum. Power supplies are thyratron switched pulse forming networks that produce microsecond width pulses of several kiloamps with less than 30 nanoseconds rise and fall times. Kicker and power supply design requirements for field strength, vacuum, rise and fall time, timing and magnetic shielding of the stacked beam in the accumulator by the eddy current shutter will be discussed. 8 refs., 3 figs., 2 tabs.

  15. Transistor-based filter for inhibiting load noise from entering a power supply

    DOE Patents [OSTI]

    Taubman, Matthew S

    2013-07-02T23:59:59.000Z

    A transistor-based filter for inhibiting load noise from entering a power supply is disclosed. The filter includes a first transistor having an emitter coupled to a power supply, a collector coupled to a load, and a base. The filter also includes a first capacitor coupled between the base of the first transistor and a ground terminal. The filter further includes an impedance coupled between the base and a node between the collector and the load, or a second transistor and second capacitor. The impedance can be a resistor or an inductor.

  16. An Integrated Electric Power Supply Chain and Fuel Market Network Framework: Theoretical Modeling with Empirical Analysis for New England

    E-Print Network [OSTI]

    Nagurney, Anna

    a critical infrastructure for the functioning of our modern economies and societies. Electric power lightsAn Integrated Electric Power Supply Chain and Fuel Market Network Framework: Theoretical Modeling; revised April 2008 Abstract: In this paper, we develop a novel electric power supply chain network model

  17. Creating high-stability high-precision bipolar trim power supply

    SciTech Connect (OSTI)

    Chen, Zhe [JLAB; Merz, William A. [JLAB

    2012-07-01T23:59:59.000Z

    Thomas Jefferson National Accelerator Facility (TJNAF) is founded by the US Department of Energy (DOE) office of science for the technology advancement and physics research in electron beam accelerator. This facility has the state of the art technology to carry out world-class cutting-edge experiments for the nucleus composition and atomic characteristics identification and exploration for the nature of the matter in the universe. A continuous wave electron beam is featured for such experiments, thus precise and stable trim power supply is required to meet such purpose. This paper demonstrates the challenges and solutions to design, assemble, fabrication and test such high-precision high-stability power supplies. This paper presents the novel design and first article test of the ±20A ±75V bipolar, 100ppm stability level current-regulated high-power trim power supplies for the beam manipulation. This special design can provide valuable documentation and reference values for future designs and special applications in particle accelerator power supply creation.

  18. Transient power supply voltage (v{sub DDT}) analysis for detecting IC defects

    SciTech Connect (OSTI)

    Cole, E.I. Jr.; Soden, J.M.; Beegle, R.W. [and others

    1997-04-01T23:59:59.000Z

    Transient power supply voltage (V{sub DDT}) analysis is a new testing technique demonstrated as a powerful alternative and complement to I{sub DDQ} testing. V{sub DDT} takes advantage of the limited response time of a voltage supply to the changing power demands of an IC during operation. Changes in the V{sub DD} response time are used to detect increases in power demand with resolutions of 100 nA at 100 kHz, 1 {mu}A at 1 MHz, and 2.5 {mu}A at 1.5 MHz. These current sensitivities have been shown for ICs with quiescent currents < 0.1 {mu}A and > 300 {mu}A. The V{sub DDT} signal acquisition protocols, frequency versus sensitivity tradeoffs, hardware considerations and limitations, data examples, and areas for future research are described.

  19. Designing criteria for building power systems supplying distributed non-linear loads

    SciTech Connect (OSTI)

    Grasselli, U.; Parise, G. [Univ. of Rome La Sapienza (Italy). Electrical Engineering Dept.

    1995-12-31T23:59:59.000Z

    In commercial and institutional buildings, the wider use of power electronics equipment, such as computer switch-mode power supplies and compact fluorescent lights with electronic ballasts, can create many problems. These loads are generally single-phase with a 3rd harmonic current that can be equal or more than 60%. The aim of this paper is that of analyzing several specific aspects of power system design, such as: sizing of circuits; and the selection of circuits, by correlating them with this specific problem of distributed nonlinear load supply. The proposed criteria can be utilized both in a short-term action for resolution of specific problems, and in medium-term action for development of new optimization procedures of power system design.

  20. Study of the Power Supply Ripple Effect on teh Dynamics at SPEAR

    SciTech Connect (OSTI)

    Terebilo, A.; Pellegrini, C.; /UCLA; Cornacchia, M.; Corbett, J.; Martin, D.; /SLAC

    2011-09-14T23:59:59.000Z

    For long term stability analysis time variation of tunes is important. We have proposed and tested a technique for measuring the magnitude of this variation. This was made possible by using tune extraction algorithms that require small number of turns thus giving an instantaneous tune of the machine. In this paper we demonstrate the measured effect of the tune modulation with 60 Hz power supplies ripple, power line interference from SLAC linac operating at 30 Hz repetition rate, and nonperiodic variation.

  1. The Economic Value of Improving the Reliability of Supply on a Bulk Power Transmission Network

    E-Print Network [OSTI]

    The Economic Value of Improving the Reliability of Supply on a Bulk Power Transmission Network Economics and Management and School of Electrical and Computer Engineering Cornell University Abstract, there is no established way of measuring the economic value of reliability, and as a result, regulators have adopted

  2. Pulsed power supply for Nova Upgrade. Final report, August 1, 1991 to March 31, 1992

    SciTech Connect (OSTI)

    Bacon, J.L.; Kajs, J.P.; Walls, A.; Weldon, W.F.; Zowarka, R.C. [Univ. of Texas, Austin, TX (US). Center for Electromechanics] [Univ. of Texas, Austin, TX (US). Center for Electromechanics

    1992-12-31T23:59:59.000Z

    This report describes work carried out at the Center for Electromechanics at The University of Texas at Austin (CEM-UT). A baseline design of the Nova Upgrade has been completed by Lawrence Livermore National Laboratory. The Nova Upgrade is an 18 beamline Nd: glass laser design utilizing fully relayed 4x4 30 cm aperture segmented optical components. The laser thus consists of 288 independent beamlets nominally producing 1.5 to 2.0 MJ of 0.35 {mu}m light in a 3 to 5 ns pulse. The laser design is extremely flexible and will allow a wide range of pulses to irradiate ICF targets. This facility will demonstrate ignition/gain and the scientific feasibility of ICF for energy and defense applications. The pulsed power requirements for the Nova Upgrade are given. CEM-UT was contracted to study and develop a design for a homopolar generator/inductor (HPG/inductor) opening switch system which would satisfy the pulsed power supply requirements of the Nova Upgrade. The Nd:glass laser amplifiers used in the Nova Upgrade will be powered by light from xenon flashlamps. The pulsed power supply for the Nova Upgrade powers the xenon flashlamps. This design and study was for a power supply to drive flashlamps.

  3. A Capacitor-Less Wide-Band Power Supply Rejection Low Drop-Out Voltage Regulator with Capacitance Multiplier

    E-Print Network [OSTI]

    Wang, Mengde

    2014-05-22T23:59:59.000Z

    A Low Drop-Out (LDO) voltage regulator with both capacitor-less and high power supply rejection (PSR) bandwidth attributes is highly admired for an integrated power management system of mobile electronics. The capacitor-less feature is demanded...

  4. Transmission Matters Now: How Will Power Market Regulations Impact the Industrial's Power Supply Costs and Reliability?

    E-Print Network [OSTI]

    James, F.; Beidas, H.; Fox, R.

    and reliability. The paper also identifies what specifically may be involved, from a technical and regulatory standpoint, in the following three areas: 1) Transmission Risks -SMD and RTO/ISO, 2) Alternative Retail Supply, and 3) Self-Generation....

  5. Regulation loops for the ring magnet power supplies in the SSC accelerator complex

    SciTech Connect (OSTI)

    Tacconi, E.; Christiansen, C.

    1993-05-01T23:59:59.000Z

    The SSC complex consists of five cascaded accelerators: The linear accelerator (linac) and four synchrotrons: The low energy booster (LEB), the medium energy booster (MEB), the high energy booster (HEB), and the collider. Twelve- or 24-pulse phase-controlled SCR power supplies are used to energize the ring magnets. Each power supply has a voltage loop designed to regulate the voltage applied to the magnets. The voltage regulation loops for these synchrotrons and the current regulation for the LEB are analyzed in this work. The digital voltage regulator is fiber-optic isolated from the power converter. It has a closed-loop bandwidth of 150 Hz with band rejections for 60-Hz and 120-Hz perturbations. The LEB has a very precise current regulation system composed of a feedforward compensator, a fast feedback regulator, and a slow synchronous regulator. The current regulation design is corroborated by computer simulations.

  6. Statistical static timing analysis considering the impact of power supply noise in VLSI circuits

    E-Print Network [OSTI]

    Kim, Hyun Sung

    2009-06-02T23:59:59.000Z

    less random than between the gates within a module. 32 REFERENCES [1] Y. M. Jiang and K. T. Cheng, ?Analysis of Performance Impact Caused by Power Supply Noise in Deep Submicron Devices,? ACM/IEEE Design Automation Conf., New... Orleans, LA, June 1999, pp. 760-765. [2] S. Pant, D. Blaauw, V. Zolotov, S. Sundareswaran and R. Panda, ?Vectorless Analysis of Supply Noise Induced Delay Variation,? IEEE/ACM Int?l Conf. Computer Aided Design, San Jose, CA, Nov. 2003, pp. 184-191. [3...

  7. Statistical static timing analysis considering the impact of power supply noise in VLSI circuits 

    E-Print Network [OSTI]

    Kim, Hyun Sung

    2009-06-02T23:59:59.000Z

    less random than between the gates within a module. 32 REFERENCES [1] Y. M. Jiang and K. T. Cheng, ?Analysis of Performance Impact Caused by Power Supply Noise in Deep Submicron Devices,? ACM/IEEE Design Automation Conf., New... Orleans, LA, June 1999, pp. 760-765. [2] S. Pant, D. Blaauw, V. Zolotov, S. Sundareswaran and R. Panda, ?Vectorless Analysis of Supply Noise Induced Delay Variation,? IEEE/ACM Int?l Conf. Computer Aided Design, San Jose, CA, Nov. 2003, pp. 184-191. [3...

  8. Page 1 of 9 SCT Bias Voltage Power Supply Specification -Version V2.04 February 2001

    E-Print Network [OSTI]

    California at Santa Cruz, University of

    Page 1 of 9 SCT Bias Voltage Power Supply Specification - Version V2.04 February 2001 Project&LV special crate, crate controller, CANbus interface to DCS E.Górnicki, S.Koperny, P.Malecki February 2001 #12;Page 2 of 9 SCT Bias Voltage Power Supply Specification - Version V2.04 February 2001 1. Scope

  9. HIGH-POWER PRECISION CURRENT SUPPLY IST2-1000M FOR ELEMENTS OF MAGNETIC SYSTEMS OF ACCELERATORS AND

    E-Print Network [OSTI]

    Kozak, Victor R.

    HIGH-POWER PRECISION CURRENT SUPPLY IST2-1000M FOR ELEMENTS OF MAGNETIC SYSTEMS OF ACCELERATORS. These supplies are intended to power magnetic systems of accelerators, requiring high stability and low ripples current at non-inductive load % 0,02 Rate of current raise without disturbing operation of the system

  10. Assessment of the Economic Potential of Microgrids for Reactive Power Supply

    SciTech Connect (OSTI)

    Appen, Jan von; Marnay, Chris; Stadler, Michael; Momber, Ilan; Klapp, David; Scheven, Alexander von

    2011-05-01T23:59:59.000Z

    As power generation from variable distributed energy resources (DER) grows, energy flows in the network are changing, increasing the requirements for ancillary services, including voltage support. With the appropriate power converter, DER can provide ancillary services such as frequency control and voltage support. This paper outlines the economic potential of DERs coordinated in a microgrid to provide reactive power and voltage support at its point of common coupling. The DER Customer Adoption Model assesses the costs of providing reactive power, given local utility rules. Depending on the installed DER, the cost minimizing solution for supplying reactive power locally is chosen. Costs include the variable cost of the additional losses and the investment cost of appropriately over-sizing converters or purchasing capacitors. A case study of a large health care building in San Francisco is used to evaluate different revenue possibilities of creating an incentive for microgrids to provide reactive power.

  11. Programmable AC power supply for simulating power transient expected in fusion reactor

    SciTech Connect (OSTI)

    Halimi, B. [Seoul National Univ., Seoul 151-744 (Korea, Republic of); Suh, K. Y. [Seoul National Univ., Seoul 151-744 (Korea, Republic of); PHILOSOPHIA, 1 Gwanak Ro, Gwanak Gu, Seoul 151-744 (Korea, Republic of)

    2012-07-01T23:59:59.000Z

    This paper focus on control engineering of the programmable AC power source which has capability to simulate power transient expected in fusion reactor. To generate the programmable power source, AC-AC power electronics converter is adopted to control the power of a set of heaters to represent the transient phenomena of heat exchangers or heat sources of a fusion reactor. The International Thermonuclear Experimental Reactor (ITER) plasma operation scenario is used as the basic reference for producing this transient power source. (authors)

  12. Load controller and method to enhance effective capacity of a photovoltaic power supply using a dynamically determined expected peak loading

    DOE Patents [OSTI]

    Perez, Richard

    2005-05-03T23:59:59.000Z

    A load controller and method are provided for maximizing effective capacity of a non-controllable, renewable power supply coupled to a variable electrical load also coupled to a conventional power grid. Effective capacity is enhanced by monitoring power output of the renewable supply and loading, and comparing the loading against the power output and a load adjustment threshold determined from an expected peak loading. A value for a load adjustment parameter is calculated by subtracting the renewable supply output and the load adjustment parameter from the current load. This value is then employed to control the variable load in an amount proportional to the value of the load control parameter when the parameter is within a predefined range. By so controlling the load, the effective capacity of the non-controllable, renewable power supply is increased without any attempt at operational feedback control of the renewable supply.

  13. Techno-economic analysis of using corn stover to supply heat and power to a corn ethanol plant - Part 1: Cost of feedstock supply logistics

    SciTech Connect (OSTI)

    Sokhansanj, Shahabaddine [ORNL; Mani, Sudhagar [University of Georgia; Togore, Sam [U.S. Department of Energy; Turhollow Jr, Anthony F [ORNL

    2010-01-01T23:59:59.000Z

    Supply of corn stover to produce heat and power for a typical 170 dam3 dry mill ethanol plant is proposed. The corn ethanol plant requires 5.6 MW of electricity and 52.3 MW of process heat, which creates the annual stover demand of as much as 140 Gg. The corn stover supply system consists of collection, preprocessing, transportation and on-site fuel storage and preparation to produce heat and power for the ethanol plant. Economics of the entire supply system was conducted using the Integrated Biomass Supply Analysis and Logistics (IBSAL) simulation model. Corn stover was delivered in three formats (square bales, dry chops and pellets) to the combined heat and power plant. Delivered cost of biomass ready to be burned was calculated at 73 $ Mg-1 for bales, 86 $ Mg-1 for pellets and 84 $ Mg-1 for field chopped biomass. Among the three formats of stover supply systems, delivered cost of pelleted biomass was the highest due to high pelleting cost. Bulk transport of biomass in the form of chops and pellets can provide a promising future biomass supply logistic system in the US, if the costs of pelleting and transport are minimized.

  14. A PULSED MODULATOR POWER SUPPLY FOR THE G-2 MUON STORAGE RING INJECTION KICKER.

    SciTech Connect (OSTI)

    MI,J.LEE,Y.Y.MORSE,W.M.PAI,C.I.PAPPAS,G.C.SANDERS,Y.SEMERTIZIDIS,Y.,ET AL.

    2003-03-01T23:59:59.000Z

    This paper describes the pulse modulator power supplies used to drive the kicker magnets that inject the muon beam into the 8-2 storage ring that has been built at Brookhaven National Laboratory. Three modulators built into coaxial structures consisting of a series circuit of an energy storage capacitor, a damping resistor and a fast thyratron switch are used to energize three magnets that kick the beam into the proper orbit. A 100 kV charging power supply is used to charge the capacitor to 95kV. The damping resistor shapes the magnet current waveform to a 450 nanosecond half-sine to match the injection requirements. This paper discusses the modulator design, construction and operation.

  15. A Pulsed Modulator Power Supply for the g-2 Muon Storage Ring Injection Kicker

    SciTech Connect (OSTI)

    Mi,J.; Lee, Y.Y.; Morse, W. M.; Pai, C.; Pappas, G.; Sanders, R.; Semertzidis, Y.

    1999-03-29T23:59:59.000Z

    This paper describes the pulse modulator power supplies used to drive the kicker magnets that inject the muon beam into the g-2 storage ring that has been built at Brookhaven. Three modulators built into coaxial structures consisting of a series circuit of an energy storage capacitor, damping resistor and a fast thyratron switch are used to energize three magnets that kick the beam into the proper orbit. A 100 kV charging power supply is used to charge the capacitor to 95 kV. the damping resistor shapes the magnet current waveform to a 450 nanosecond half-sine to match the injection requirements. this paper discusses the modulator design, construction and operation.

  16. Wind Power Project Repowering: Financial Feasibility, Decision Drivers, and Supply Chain Effects

    SciTech Connect (OSTI)

    Lantz, E.; Leventhal, M.; Baring-Gould, I.

    2013-12-01T23:59:59.000Z

    As wind power facilities age, project owners are faced with plant end of life decisions. This report is intended to inform policymakers and the business community regarding the history, opportunities, and challenges associated with plant end of life actions, in particular repowering. Specifically, the report details the history of repowering, examines the plant age at which repowering becomes financially attractive, and estimates the incremental market investment and supply chain demand that might result from future U.S. repowering activities.

  17. The key word is "supplying." In a load center or panel board, the main circuit breaker supplies power to the internal

    E-Print Network [OSTI]

    Johnson, Eric E.

    power to the internal bus bars, as do any backfed circuit breakers supplying power from the PV inverters these numbers translate to a 3,840-watt (AC inverter output) PV system on a 100-amp panel and a 7,680-watt PV on the circuit breakers. Many common PV inverters are rated at 2,500 watts and 240 volts. The rated output

  18. Biomass plants face wood supply risks Report warns giant new biomass power plants will be hugely reliant on wood chip

    E-Print Network [OSTI]

    Biomass plants face wood supply risks Report warns giant new biomass power plants will be hugely's biomass energy sector could be undermined unless businesses move to resolve the supply chain issues-scale biomass plants will leave generators largely reliant on biomass from overseas such as wood chips, elephant

  19. POWER SUPPLY SYSTEM FOR CORRECTING MAGNETS OF VEPP-2000 O. Belikov, D. Berkaev, V. Kozak, A. Medvedko, BINP, Novosibirsk, Russia

    E-Print Network [OSTI]

    Kozak, Victor R.

    POWER SUPPLY SYSTEM FOR CORRECTING MAGNETS OF VEPP-2000 COMPLEX O. Belikov, D. Berkaev, V. Kozak, A is corrected with the help of correcting windings. Each winding is powered from an individual, four-quadrant current source (power amplifier) of the PA-6 or PA-20 type. The current sources are made with up

  20. SYSTEM OF POWER SUPPLY RIPPLES MEASUREMENT FOR VEPP-2000 D. Berkaev, O. Belikov, V. Kozak, P. Shatunov, A. Medvedko

    E-Print Network [OSTI]

    Kozak, Victor R.

    SYSTEM OF POWER SUPPLY RIPPLES MEASUREMENT FOR VEPP-2000 COLLIDER D. Berkaev, O. Belikov, V. Kozak parameters maintaining. The standard power sources automation system does not allow discovering for the aims of the pulsation discovering. In oscillographic regime the system e gets measurements of all power

  1. Numerical simulation of the thermal conditions in a sea bay water area used for water supply to nuclear power plants

    SciTech Connect (OSTI)

    Sokolov, A. S. [JSC 'B. E. Vedeneev All-Russia Research Institute of Hydraulic Engineering (VNIIG)' (Russian Federation)] [JSC 'B. E. Vedeneev All-Russia Research Institute of Hydraulic Engineering (VNIIG)' (Russian Federation)

    2013-07-15T23:59:59.000Z

    Consideration is given to the numerical simulation of the thermal conditions in sea water areas used for both water supply to and dissipation of low-grade heat from a nuclear power plant on the shore of a sea bay.

  2. The design of a regulated variable power supply for transistor circuits

    E-Print Network [OSTI]

    Graham, Oscar David

    1959-01-01T23:59:59.000Z

    voltmeter the lind. tstien on the number of significant figures, a method had to be devised to measure small voltage changes st, high voltage levels. An arrangement wss made to measure the dif- ference between a constant voltage reference and the output... require- ments of' prscticaLly all low power transistor circuits. The supply may be contraLLed by one main control knob for ease in operation. The i'inal d. esign (schematic on page 32) wss operated. under load. conditions where measurements were taken...

  3. Design and Manufacture of the RF Power Supply and RF Transmission Line for SANAEM Project Prometheus

    E-Print Network [OSTI]

    Turemen, G; Unel, G; Alacakir, A

    2015-01-01T23:59:59.000Z

    A 1-5 MeV proton beamline is being built by the Turkish Atomic Energy Authority in collaboration with a number of graduate students from different universities. The most important aspect of the project, is to acquire the design ability and manufacturing capability of all the components locally. SPP will be an accelerator and beam diagnostics test facility and it will also serve the detector development community with its low beam current. This paper discusses the design and construction of the RF power supply and the RF transmission line components such as its waveguide converters and its circulator.

  4. Performance of East Olkaria Power Plant and plans for maintaining steam supply in the future

    SciTech Connect (OSTI)

    Ouma, P.A.; Aloo, P.O. [Kenya Power Company, Naivasha (Kenya)

    1995-12-31T23:59:59.000Z

    Olkaria East geothermal power plant has been in operation since 1981. The wells that supply the plant produce two phase fluid from a 240-340{degrees}C hot, low gas, liquid dominated reservoir which is related to volcanic pile and fractures. Separated steam from twenty seven (27) wells, flows to 3 x 15 MWe Mitsubishi direct contact condensing units while the brine is disposed off through infiltration ponds. The plant performance has been excellent with the plant equipment remaining in good shape after fourteen (14) years of operation as a result of favourable chemistry of discharge fluid. As predicted in the Reservoir Simulation studies for this field, there has been gradual decline in steam production from the wells supplying the plant. In order to maintain adequate supply of steam to the plant in the future, two schemes are being advanced. The first scheme is to re-inject water into the reservoir to offset the reservoir pressure drawdown and steam decline and effectively, limit the number of make-up wells to be drilled and connected to the plant. Secondly, leave out re-injection and establish a scheme for drilling and connection of the make-up wells. The cost implication of either of the alternatives has been addressed.

  5. Reliability evaluation of the power supply of an electrical power net for safety-relevant applications

    E-Print Network [OSTI]

    Liberzon, Daniel

    automotive safety-relevant systems. With the introduction of safety-relevant electronic systems in cars the failure mechanisms in order to improve the design. Several system level FMEAs are used to identify of occurrence. A new power net architecture with application to new safety-relevant automotive systems

  6. Multimode power processor

    DOE Patents [OSTI]

    O'Sullivan, George A. (Pottersville, NJ); O'Sullivan, Joseph A. (St. Louis, MO)

    1999-01-01T23:59:59.000Z

    In one embodiment, a power processor which operates in three modes: an inverter mode wherein power is delivered from a battery to an AC power grid or load; a battery charger mode wherein the battery is charged by a generator; and a parallel mode wherein the generator supplies power to the AC power grid or load in parallel with the battery. In the parallel mode, the system adapts to arbitrary non-linear loads. The power processor may operate on a per-phase basis wherein the load may be synthetically transferred from one phase to another by way of a bumpless transfer which causes no interruption of power to the load when transferring energy sources. Voltage transients and frequency transients delivered to the load when switching between the generator and battery sources are minimized, thereby providing an uninterruptible power supply. The power processor may be used as part of a hybrid electrical power source system which may contain, in one embodiment, a photovoltaic array, diesel engine, and battery power sources.

  7. Multimode power processor

    DOE Patents [OSTI]

    O'Sullivan, G.A.; O'Sullivan, J.A.

    1999-07-27T23:59:59.000Z

    In one embodiment, a power processor which operates in three modes: an inverter mode wherein power is delivered from a battery to an AC power grid or load; a battery charger mode wherein the battery is charged by a generator; and a parallel mode wherein the generator supplies power to the AC power grid or load in parallel with the battery. In the parallel mode, the system adapts to arbitrary non-linear loads. The power processor may operate on a per-phase basis wherein the load may be synthetically transferred from one phase to another by way of a bumpless transfer which causes no interruption of power to the load when transferring energy sources. Voltage transients and frequency transients delivered to the load when switching between the generator and battery sources are minimized, thereby providing an uninterruptible power supply. The power processor may be used as part of a hybrid electrical power source system which may contain, in one embodiment, a photovoltaic array, diesel engine, and battery power sources. 31 figs.

  8. Blue Shield ensures uninterrupted access to quality medical care after Palm Drive Hospital ceases operations

    E-Print Network [OSTI]

    Ravikumar, B.

    Blue Shield ensures uninterrupted access to quality medical care after Palm Drive Hospital ceases and inpatient services due to the hospital's bankruptcy filing. This closure affects Blue Shield HMO plan members who have been utilizing Palm Drive Hospital services. Please be advised that Blue Shield

  9. Load controller and method to enhance effective capacity of a photovotaic power supply using a dynamically determined expected peak loading

    DOE Patents [OSTI]

    Perez, Richard (Delmar, NY)

    2003-04-01T23:59:59.000Z

    A load controller and method are provided for maximizing effective capacity of a non-controllable, renewable power supply coupled to a variable electrical load also coupled to a conventional power grid. Effective capacity is enhanced by monitoring power output of the renewable supply and loading, and comparing the loading against the power output and a load adjustment threshold determined from an expected peak loading. A value for a load adjustment parameter is calculated by subtracting the renewable supply output and the load adjustment parameter from the current load. This value is then employed to control the variable load in an amount proportional to the value of the load control parameter when the parameter is within a predefined range. By so controlling the load, the effective capacity of the non-controllable, renewable power supply is increased without any attempt at operational feedback control of the renewable supply. The expected peak loading of the variable load can be dynamically determined within a defined time interval with reference to variations in the variable load.

  10. Comparison of Test Procedures and Energy Efficiency Criteria in Selected International Standards & Labeling Programs for Copy Machines, External Power Supplies, LED Displays, Residential Gas Cooktops and Televisions

    E-Print Network [OSTI]

    Zheng, Nina

    2013-01-01T23:59:59.000Z

    external-power- supplies/meps/ Australia E3. 2012. “EU, Australia and Japan all have maximum power consumptionEU, Australia and Japan all have maximum power consumption

  11. A Preliminary Analysis of the Economics of Using Distributed Energy as a Source of Reactive Power Supply

    SciTech Connect (OSTI)

    Li, Fangxing [ORNL; Kueck, John D [ORNL; Rizy, D Tom [ORNL; King, Thomas F [ORNL

    2006-04-01T23:59:59.000Z

    A major blackout affecting 50 million people in the Northeast United States, where insufficient reactive power supply was an issue, and an increased number of filings made to the Federal Energy Regulatory Commission by generators for reactive power has led to a closer look at reactive power supply and compensation. The Northeastern Massachusetts region is one such area where there is an insufficiency in reactive power compensation. Distributed energy due to its close proximity to loads seems to be a viable option for solving any present or future reactive power shortage problems. Industry experts believe that supplying reactive power from synchronized distributed energy sources can be 2 to 3 times more effective than providing reactive support in bulk from longer distances at the transmission or generation level. Several technology options are available to supply reactive power from distributed energy sources such as small generators, synchronous condensers, fuel cells or microturbines. In addition, simple payback analysis indicates that investments in DG to provide reactive power can be recouped in less than 5 years when capacity payments for providing reactive power are larger than $5,000/kVAR and the DG capital and installation costs are lower than $30/kVAR. However, the current institutional arrangements for reactive power compensation present a significant barrier to wider adoption of distributed energy as a source of reactive power. Furthermore, there is a significant difference between how generators and transmission owners/providers are compensated for reactive power supplied. The situation for distributed energy sources is even more difficult, as there are no arrangements to compensate independent DE owners interested in supplying reactive power to the grid other than those for very large IPPs. There are comparable functionality barriers as well, as these smaller devices do not have the control and communications requirements necessary for automatic operation in response to local or system operators. There are no known distributed energy asset owners currently receiving compensation for reactive power supply or capability. However, there are some cases where small generators on the generation and transmission side of electricity supply have been tested and have installed the capability to be dispatched for reactive power support. Several concerns need to be met for distributed energy to become widely integrated as a reactive power resource. The overall costs of retrofitting distributed energy devices to absorb or produce reactive power need to be reduced. There needs to be a mechanism in place for ISOs/RTOs to procure reactive power from the customer side of the meter where distributed energy resides. Novel compensation methods should be introduced to encourage the dispatch of dynamic resources close to areas with critical voltage issues. The next phase of this research will investigate in detail how different options of reactive power producing DE can compare both economically and functionally with shunt capacitor banks. Shunt capacitor banks, which are typically used for compensating reactive power consumption of loads on distribution systems, are very commonly used because they are very cost effective in terms of capital costs. However, capacitor banks can require extensive maintenance especially due to their exposure to lightning at the top of utility poles. Also, it can be problematic to find failed capacitor banks and their maintenance can be expensive, requiring crews and bucket trucks which often requires total replacement. Another shortcoming of capacitor banks is the fact that they usually have one size at a location (typically sized as 300, 600, 900 or 1200kVAr) and thus don't have variable range as do reactive power producing DE, and cannot respond to dynamic reactive power needs. Additional future work is to find a detailed methodology to identify the hidden benefit of DE for providing reactive power and the best way to allocate the benefit among customers, utilities, transmission companies or RTOs.

  12. Atmospheric pressure plasma jet with high-voltage power supply based on piezoelectric transformer

    SciTech Connect (OSTI)

    Babij, Micha?; Kowalski, Zbigniew W., E-mail: zbigniew.w.kowalski@pwr.wroc.pl; Nitsch, Karol; Gotszalk, Teodor [Wroc?aw University of Technology, Wybrze?e Wyspia?skiego 27, 50-370 Wroc?aw (Poland)] [Wroc?aw University of Technology, Wybrze?e Wyspia?skiego 27, 50-370 Wroc?aw (Poland); Silberring, Jerzy [AGH University of Science and Technology, Al. A. Mickiewicza 30, 30-059 Kraków (Poland)] [AGH University of Science and Technology, Al. A. Mickiewicza 30, 30-059 Kraków (Poland)

    2014-05-15T23:59:59.000Z

    The dielectric barrier discharge plasma jet, an example of the nonthermal atmospheric pressure plasma jet (APPJ), generates low-temperature plasmas that are suitable for the atomization of volatile species and can also be served as an ionization source for ambient mass and ion mobility spectrometry. A new design of APPJ for mass spectrometry has been built in our group. In these plasma sources magnetic transformers (MTs) and inductors are typically used in power supplies but they present several drawbacks that are even more evident when dealing with high-voltage normally used in APPJs. To overcome these disadvantages, high frequency generators with the absence of MT are proposed in the literature. However, in the case of miniaturized APPJs these conventional power converters, built of ferromagnetic cores and inductors or by means of LC resonant tank circuits, are not so useful as piezoelectric transformer (PT) based power converters due to bulky components and small efficiency. We made and examined a novel atmospheric pressure plasma jet with PT supplier served as ionization source for ambient mass spectrometry, and especially mobile spectrometry where miniaturization, integration of components, and clean plasma are required. The objective of this paper is to describe the concept, design, and implementation of this miniaturized piezoelectric transformer-based atmospheric pressure plasma jet.

  13. A high voltage pulsed power supply for capillary discharge waveguide applications

    SciTech Connect (OSTI)

    Abuazoum, S.; Wiggins, S. M.; Issac, R. C.; Welsh, G. H.; Vieux, G.; Jaroszynski, D. A. [Department of Physics, Scottish Universities Physics Alliance, University of Strathclyde, Glasgow G4 0NG (United Kingdom); Ganciu, M. [Low Temperature Plasma Department, National Institute of Lasers, Plasma and Radiation Physics, 077125, Magurele, Bucharest (Romania)

    2011-06-15T23:59:59.000Z

    We present an all solid-state, high voltage pulsed power supply for inducing stable plasma formation (density {approx}10{sup 18} cm{sup -3}) in gas-filled capillary discharge waveguides. The pulser (pulse duration of 1 {mu}s) is based on transistor switching and wound transmission line transformer technology. For a capillary of length 40 mm and diameter 265 {mu}m and gas backing pressure of 100 mbar, a fast voltage pulse risetime of 95 ns initiates breakdown at 13 kV along the capillary. A peak current of {approx}280 A indicates near complete ionization, and the r.m.s. temporal jitter in the current pulse is only 4 ns. Temporally stable plasma formation is crucial for deploying capillary waveguides as plasma channels in laser-plasma interaction experiments, such as the laser wakefield accelerator.

  14. Development of a lithium hydride powered hydrogen generator for use in long life, low power PEM fuel cell power supplies

    E-Print Network [OSTI]

    Strawser, Daniel DeWitt

    2012-01-01T23:59:59.000Z

    This thesis studies a hybrid PEM fuel cell system for use in low power, long life sensor networks. PEM fuel cells offer high efficiency and environmental friendliness but have not been widely adopted due to cost, reliability, ...

  15. Seismic fragility of nuclear power plant components: Phase 2, Motor control center, switchboard, panelboard and power supply

    SciTech Connect (OSTI)

    Bandyopadhyay, K.K.; Hofmayer, C.H.; Kassir, M.K.; Pepper, S.E.

    1987-12-01T23:59:59.000Z

    In Phase I of the Component Fragility Program, Brookhaven National Laboratory (BNL) has developed a procedure to establish the seismic fragility of nuclear power plant equipment by use of existing test data and demonstrated its application by considering two equipment pieces. In Phase II of the program, BNL has collected additional test data, and has further advanced and is applying the methodology to determine the fragility levels of selected essential equipment categories. The data evaluation of four equipment families, namely, motor control center, switchboard, panelboard and power supply has been completed. Fragility levels have been determined for various failure modes of each equipment class and the deterministic results are presented in terms of test response spectra. In addition, the test data have been analyzed for determination of the respective probabilistic fragility levels. To this end, a single g-value has been selected to approximately represent the test vibration level and a statistical analysis has been performed with the g-values corresponding to a particular failure mode. The zero period acceleration and the average spectral acceleration over a frequency range of interest are separately used as the single g-value. The resulting parameters are presented in terms of a median value, an uncertainty coefficient and a randomness coefficient. Ultimately, each fragility level is expressed in terms of a single descriptor called an HCLPF value corresponding to a high (95%) confidence of a low (5%) probability of failure. The important observations made in the process of data analysis are included in this report.

  16. We Need to Talk... Developing Communicating Power Supplies to Monitor & Control Miscellaneous Electric Loads

    SciTech Connect (OSTI)

    Weber, Andrew; Lanzisera, Steven; Liao, Anna; Meier, Alan

    2014-08-11T23:59:59.000Z

    Plug loads represent 30percent of total electricity use in residential buildings. Significant energy savings would result from an accurate understanding of which miscellaneous electric devices are using energy, at what time, and in what quantity. Commercially available plug load monitoring and control solutions replace or limit the attached device's native controls - forcing the user to adapt to a separate set of controls associated with the monitoring and control hardware. A better solution is integration of these capabilities at the power supply level. In this paper, we demonstrate a method achieving this integration. Our solution allows unobtrusive power monitoring and control while retaining native device control features. Further, our prototype enables intelligent behaviors by allowing devices to respond to the state of one another automatically. The CPS enables energy savings while demonstrating an added level of functionality to the user. If CPS technology became widespread in devices, a combination of automated and human interactive solutions would enable high levels of energy savings in buildings.

  17. Commissioning and Operation of 130kV/130A Switched-Mode HV Power Supplies with the Upgraded JET Neutral Beam Injectors

    E-Print Network [OSTI]

    Commissioning and Operation of 130kV/130A Switched-Mode HV Power Supplies with the Upgraded JET Neutral Beam Injectors

  18. Proposal for the award of a blanket purchase contract for the supply of numerical relays for the protection of electrical power systems

    E-Print Network [OSTI]

    2010-01-01T23:59:59.000Z

    Proposal for the award of a blanket purchase contract for the supply of numerical relays for the protection of electrical power systems

  19. Department of Energy refurbish power supply/distribution system: Phase 2, Y-12 Plant, Oak Ridge. Project status report No. 40, December 1--31, 1994

    SciTech Connect (OSTI)

    NONE

    1994-12-31T23:59:59.000Z

    A status report on the refurbishing of the power supply and distribution system for the Y-12 Plant is presented. A milestone schedule is included.

  20. Proposal to negotiate the renewal of a blanket purchase contract for the supply of high-power RF grid-tubes for the CERN accelerators

    E-Print Network [OSTI]

    2014-01-01T23:59:59.000Z

    Proposal to negotiate the renewal of a blanket purchase contract for the supply of high-power RF grid-tubes for the CERN accelerators

  1. Improvement of power supply EMC by chaos J.H.B. Deane and D.C. Hamill

    E-Print Network [OSTI]

    Deane, Jonathan

    Improvement of power supply EMC by chaos J.H.B. Deane and D.C. Hamill Department of Electronic is spread, its peaks are reduced and EMC is improved, compared to the case when the circuit is operating consisting of the switching frequency and many harmonics. Such interference poses significant EMC problems

  2. Outages of electric power supply resulting from cable failures Boston Edison Company system

    SciTech Connect (OSTI)

    None

    1980-07-01T23:59:59.000Z

    Factual data are provided regarding 5 electric power supply interruptions that occurred in the Boston Metropolitan area during April to June, 1979. Common to all of these outages was the failure of an underground cable as the initiating event, followed by multiple equipment failures. There was significant variation in the voltage ratings and types of cables which failed. The investigation was unable to delineate a single specific Boston Edison design operating or maintenance practice that could be cited as the cause of the outages. After reviewing the investigative report the following actions were recommended: the development and implementation of a plan to eliminate the direct current cable network; develop a network outage restoration plan; regroup primary feeder cables wherever possible to minimize the number of circuits in manholes, and to separate feeders to high load density areas; develop a program to detect incipient cable faults; evaluate the separation of the north and south sections of Back Bay network into separate networks; and, as a minimum, install the necessary facilities to make it possible to re-energize one section without interfering with the other; and re-evaluate the cathodic protection scheme where necessary. (LCL)

  3. Solid core dipoles and switching power supplies: lower cost light sources?

    E-Print Network [OSTI]

    Benesch, Jay; Facility, Thomas Jefferson National Accelerator

    2015-01-01T23:59:59.000Z

    As a result of improvements in power semiconductors, moderate frequency switching supplies can now provide the hundreds of amps typically required by accelerators with zero-to-peak noise in the kHz region ~0.06% in current or voltage mode. Modeling was undertaken using a finite electromagnetic program to determine if eddy currents induced in the solid steel of CEBAF magnets and small supplemental additions would bring the error fields down to the 5ppm level needed for beam quality. The expected maximum field of the magnet under consideration is 0.85T and the DC current required to produce that field is used in the calculations. An additional 0.1% current ripple is added to the DC current at discrete frequencies 360 Hz, 720 Hz or 7200 Hz. Over the region of the pole within 0.5% of the central integrated BdL the resulting AC field changes can be reduced to less than 1% of the 0.1% input ripple for all frequencies, and a sixth of that at 7200 Hz. Doubling the current, providing 1.5T central field, yielded the sa...

  4. Lab 4 -Motor Constants and Sensor Calibration Consider a DC servo motor which is connected to a power supply. The motor inertia is Jm. The rotational

    E-Print Network [OSTI]

    Stanford University

    Lab 4 - Motor Constants and Sensor Calibration PRE-LAB Consider a DC servo motor which is connected to a power supply. The motor inertia is Jm. The rotational damping in the motor is bm. The motor produces a torque Tm = Kmi where Km is the motor's torque constant and i is the current from the power supply. a

  5. CONTROL SYSTEM FOR ELECTROMAGNET POWER SUPPLIES E.Y.Ermolov, V.R.Kozak, E.A.Kuper, A.S.Medvedko, S.P.Petrov, V.F.Veremeenko, BINP,

    E-Print Network [OSTI]

    Kozak, Victor R.

    THAP053 CONTROL SYSTEM FOR ELECTROMAGNET POWER SUPPLIES E.Y.Ermolov, V.R.Kozak, E.A.Kuper, A require high stability and accuracy of power supplies. Typical requirements to accuracy of this power is inexpensive multi-channel device for multi-channel power supply systems for correctors. A precise controller

  6. Fuel-supply structure of wood-fired power plants in the Northeast: Loggers' perspective. Forest Service research paper

    SciTech Connect (OSTI)

    Huyler, N.K.

    1989-07-01T23:59:59.000Z

    This study gauges loggers' perceptions of the impact of large biomass demand centers (electrical power generation) on the forest resource base in the Northeast. The loggers who supply these demand centers are business people with large capital investments in highly mechanized harvesting systems. Most of the loggers surveyed strongly believed that the post-harvest stand has improved as a result of fuel-wood chipping; however, the impact of chip harvesting on the forest resource base was not clear.

  7. Effect of dopants on the magnetic properties of MnZn ferrites for high frequency power supplies

    SciTech Connect (OSTI)

    Znidarsic, A.; Limpel, M.; Drofenik, M. [Univ. of Ljubljana (Slovenia)] [Univ. of Ljubljana (Slovenia)

    1995-03-01T23:59:59.000Z

    The effect of additions on the magnetic properties of MnZn ferrites for high frequency power supplies was studied. The investigation revealed that various combinations of dopants added to the ferrite modify the grain boundary resistivity and the magnetic permeability spectra at constant microstructure. Particularly, the combined effect of Sn{sup 4+}, Ti{sup 4+} and Ta{sup 5+} was found to increase the grain boundary resistivity in the ferrites studied and remarkably decrease the power loss at higher frequencies.

  8. THE SYSTEM OF POWER SUPPLIES, CONTROL AND MODULATION OF ELECTRON GUN FOR FREE ELECTRON LASER

    E-Print Network [OSTI]

    Kozak, Victor R.

    inverter, timer and two fiber optic converters. Power inverter has 220V input line with 50 or 60Hz. The output of power inverter is connected to input coil of isolated power transformer (300kV). Timer Optic converter St 1GHz ACStabilazer Power Inverter 20kHz CAN Fiber Optic Converter 1MHz St Fiber Optic

  9. CONTROL SYSTEM FOR ELECTROMAGNET POWER SUPPLIES V.R.Kozak, E.A.Kuper, A.S.Medvedko, S.P.Petrov, V.F.Veremeenko, BINP, Novosibirsk, Russia

    E-Print Network [OSTI]

    Kozak, Victor R.

    CONTROL SYSTEM FOR ELECTROMAGNET POWER SUPPLIES V.R.Kozak, E.A.Kuper, A.S.Medvedko, S.P.Petrov, V of first group require high stability and accuracy of power supplies. Typical requirements to accuracy. The second is inexpensive multi-channel device for multi-channel power supply systems for correctors

  10. A supply chain network design model for biomass co-firing in coal-fired power plants

    SciTech Connect (OSTI)

    Md. S. Roni; Sandra D. Eksioglu; Erin Searcy; Krishna Jha

    2014-01-01T23:59:59.000Z

    We propose a framework for designing the supply chain network for biomass co-firing in coal-fired power plants. This framework is inspired by existing practices with products with similar physical characteristics to biomass. We present a hub-and-spoke supply chain network design model for long-haul delivery of biomass. This model is a mixed integer linear program solved using benders decomposition algorithm. Numerical analysis indicates that 100 million tons of biomass are located within 75 miles from a coal plant and could be delivered at $8.53/dry-ton; 60 million tons of biomass are located beyond 75 miles and could be delivered at $36/dry-ton.

  11. Investigation of DC distribution by measuring and modelling power supply devices for buildings with PV

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    control (grid-supplied induction motors and universal motors) stand as exceptions to this rule. However. Introduction Since the last building standards or eco-labels were created, the trend is to reduce building, recent work [3] revealed that using variable speed control on these electromechanical loads (passing

  12. july/august 2005 IEEE power & energy magazine 491540-7977/05/$20.002005 IEEE SOUTH AMERICA IS FACING IMPORTANT CHALLENGES IN ELECTRICITY SUPPLY

    E-Print Network [OSTI]

    Catholic University of Chile (Universidad Católica de Chile)

    Brazil and Chile progress into a second stage of reforms with public power purchase agreement (PPAjuly/august 2005 IEEE power & energy magazine 491540-7977/05/$20.00©2005 IEEE S SOUTH AMERICA;50 IEEE power & energy magazine july/august 2005 Economic Growth and Energy Supply All developing

  13. LS-69 DEVELOPING PULSE WIDTH MODULATED POWER SUPPLY FOR THE GeV...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Connected Load 2.3 Resonant Power Converter With Parallel Connected Load TWO-QUADRANT POWER CONTROLLERS 3.1 Transistorized Two-Quadrant Chopper Control 3.2 3.3 Resonant...

  14. Global nuclear power supply chains and the rise of China's nuclear industry

    E-Print Network [OSTI]

    Metzler, Florian

    2012-01-01T23:59:59.000Z

    China has embarked on a massive expansion of nuclear power that may fundamentally change the global nuclear industry, for better or for worse. Some industry observers argue that the incumbent nuclear power companies are ...

  15. Assessment of the Economic Potential of Microgrids for Reactive Power Supply

    E-Print Network [OSTI]

    Appen, Jan von

    2012-01-01T23:59:59.000Z

    Load ( kW) June (Summer) December (Winter) Hours (h) Fig. 2: Representative weekday real power profiles

  16. A Design-Oriented Framework to Determine the Parasitic Parameters of High Frequency Magnetics in Switching Power Supplies using Finite Element Analysis Techniques

    E-Print Network [OSTI]

    Shadmand, Mohammad

    2012-07-16T23:59:59.000Z

    A DESIGN-ORIENTED FRAMEWORK TO DETERMINE THE PARASITIC PARAMETERS OF HIGH FREQUENCY MAGNETICS IN SWITCING POWER SUPPLIES USING FINITE ELEMENT ANALYSIS TECHNIQUES A Thesis by MOHAMMAD BAGHER SHADMAND Submitted to the Office... to Determine the Parasitic Parameters of High Frequency Magnetics in Switching Power Supplies using Finite Element Analysis Techniques Copyright 2012 Mohammad Bagher Shadmand A DESIGN-ORIENTED FRAMEWORK TO DETERMINE THE PARASITIC PARAMETERS OF HIGH...

  17. Optimal restoration of power supply in large distribution systems in developing countries

    SciTech Connect (OSTI)

    Devi, V.S.; Sen Gupta, D.P. [Indian Inst. of Science, Bangalore (India). Dept. of Electrical Engineering; Anandalingam, G. [Univ. of Pennsylvania, Philadelphia, PA (United States). Dept. of Systems Engineering

    1995-01-01T23:59:59.000Z

    A computer aided optimal method has been developed for the restoration of electric supply to areas isolated from the network following a fault in a distribution system. A search technique is used where the search is guided by appropriate heuristics. The optimum solution entails finding the strategy which involves the operation of minimum number of switch gear for rerouting the supply within the constraint of specified loading. This is an essential requirement in countries like India where the circuit breakers are almost always manually operated and a number of transformers and feeders operate close to their rated capacity. It pays therefore to adopt different strategies at peak load and off peak conditions since the number of breaker operations is so critical. The heuristic search that is developed is applied to a large distribution system and provides very good results.

  18. Vehicle Technologies Office Merit Review 2014: North American Power Electronics Supply Chain Analysis

    Broader source: Energy.gov [DOE]

    Presentation given by Synthesis Partners at 2014 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about North American power...

  19. Spatially Differentiated Trade of Permits for Multipollutant Electric Power Supply Chains

    E-Print Network [OSTI]

    Nagurney, Anna

    ) Springer 1 Introduction Electric power plants emit several different air pollutants, such as carbon dioxide],[2]. Moreover, SO2, NOx, and Hg have important spatial characteristics; that is, the impacts of these pollutants for the substitutability or complementarity of emissions from power plants. As one pollutant is reduced, another may rise

  20. Redundancy of Supply in the International Nuclear Fuel Fabrication Market: Are Fabrication Services Assured?

    SciTech Connect (OSTI)

    Seward, Amy M.; Toomey, Christopher; Ford, Benjamin E.; Wood, Thomas W.; Perkins, Casey J.

    2011-11-14T23:59:59.000Z

    For several years, Pacific Northwest National Laboratory (PNNL) has been assessing the reliability of nuclear fuel supply in support of the U.S. Department of Energy/National Nuclear Security Administration. Three international low enriched uranium reserves, which are intended back up the existing and well-functioning nuclear fuel market, are currently moving toward implementation. These backup reserves are intended to provide countries credible assurance that of the uninterrupted supply of nuclear fuel to operate their nuclear power reactors in the event that their primary fuel supply is disrupted, whether for political or other reasons. The efficacy of these backup reserves, however, may be constrained without redundant fabrication services. This report presents the findings of a recent PNNL study that simulated outages of varying durations at specific nuclear fuel fabrication plants. The modeling specifically enabled prediction and visualization of the reactors affected and the degree of fuel delivery delay. The results thus provide insight on the extent of vulnerability to nuclear fuel supply disruption at the level of individual fabrication plants, reactors, and countries. The simulation studies demonstrate that, when a reasonable set of qualification criteria are applied, existing fabrication plants are technically qualified to provide backup fabrication services to the majority of the world's power reactors. The report concludes with an assessment of the redundancy of fuel supply in the nuclear fuel market, and a description of potential extra-market mechanisms to enhance the security of fuel supply in cases where it may be warranted. This report is an assessment of the ability of the existing market to respond to supply disruptions that occur for technical reasons. A forthcoming report will address political disruption scenarios.

  1. Dynamic pricing and stabilization of supply and demand in modern electric power grids

    E-Print Network [OSTI]

    Roozbehani, Mardavij

    The paper proposes a mechanism for real-time pricing of electricity in smart power grids, with price stability as the primary concern. In previous publications the authors argued that relaying the real-time wholesale market ...

  2. Power Supply Rejection Improvement Techniques In Low Drop-Out Voltage Regulators 

    E-Print Network [OSTI]

    Ganta, Saikrishna

    2011-10-21T23:59:59.000Z

    Efficency Load q DD I V P I I V ? ? (1.4) Typically the quiescent current of LDO is designed to be less than hundred micro amperes, while the maximum load current can be few hundreds of milliamperes, thus... at maximum loading conditions power efficiency is given by out Efficency DD V P V ? (1.5) Thus for maximum loading conditions power efficiency...

  3. Heat pipe cooled reactors for multi-kilowatt space power supplies

    SciTech Connect (OSTI)

    Ranken, W.A.; Houts, M.G.

    1995-01-01T23:59:59.000Z

    Three nuclear reactor space power system designs are described that demonstrate how the use of high temperature heat pipes for reactor heat transport, combined with direct conversion of heat to electricity, can result in eliminating pumped heat transport loops for both primary reactor cooling and heat rejection. The result is a significant reduction in system complexity that leads to very low mass systems with high reliability, especially in the power range of 1 to 20 kWe. In addition to removing heat exchangers, electromagnetic pumps, and coolant expansion chambers, the heat pipe/direct conversion combination provides such capabilities as startup from the frozen state, automatic rejection of reactor decay heat in the event of emergency or accidental reactor shutdown, and the elimination of single point failures in the reactor cooling system. The power system designs described include a thermoelectric system that can produce 1 to 2 kWe, a bimodal modification of this system to increase its power level to 5 kWe and incorporate high temperature hydrogen propulsion capability, and a moderated thermionic reactor concept with 5 to 20 kWe power output that is based on beryllium modules that thermally couple cylindrical thermionic fuel elements (TFEs) to radiator heat pipes.

  4. Abstract--It is now widely accepted within the electrical power supply industry that future power systems will operate with

    E-Print Network [OSTI]

    Taylor, Gary

    . Hobson, C. Huang, P. Kyberd and R. J. Taylor, Sensors & Instrumentation Research Group, Brunel University was supported in part by the EU under the GRIDCC Grant. G. A. Taylor and M. R. Irving, Brunel Institute of Power Systems, Brunel University, Uxbridge, Middlesex, UB8 3PH, UK (e-mail: Gareth.Taylor@brunel.ac.uk). P. R

  5. Potential for a cycling steam power plant with TES to supply district heating in Washington DC

    SciTech Connect (OSTI)

    Hobson, M.J.

    1984-02-01T23:59:59.000Z

    The Energy Office of the District of Columbia is planning the conversion of a 1500 TPD incinerator for district heating and the generation of electric power for sale to the local utility, PEPCO. This paper records a preliminary evaluation of whether hot water storage would be appropriate at the heat source plant to maximize power sales and improve the reliability of the district heat service. Hot water storage is being employed successfully at Herning, Denmark, in conjunction with a cogeneration plant heat source, and this concept is adapted to Washington D.C. area needs for heating and cooling service. Heat storage allows a 7% increase in power sales based on a simplified approach to daily load profiles and PEPCO's proposed avoided cost rates. Pressurized storage is uneconomic due to the high cost of containment, but atmospheric storage at 200F shows a simple payback of 5 years.

  6. Choosing the Right Electrical Power Supply Scientists could find clues for answering these and oth-

    E-Print Network [OSTI]

    lifetimes. An eighth RPS configuration, called the Multi-Mission Radioisotope Thermoelectric Generator a Radioisotope Power System (RPS). An RPS converts the heat generated by the natural decay of the radioactive in space and on plan- etary surfaces. Developing and Improving RPS Technology Seven generations of RPS have

  7. Modeling of Electric Power Supply Chain Networks with Fuel Suppliers Variational Inequalities

    E-Print Network [OSTI]

    Nagurney, Anna

    primary energy (coal, natural gas, uranium, and oil), or approximately 40 quadrillion BTU (British Thermal, and more than six billion Mcfs (thousand cubic feet) of natural gas were used in producing electric power Edison Electric Institute (2000), US Energy Information Administration (2002, 2005)). The US electric

  8. Spatially Differentiated Trade of Permits for Multipollutant Electric Power Supply Chains

    E-Print Network [OSTI]

    Nagurney, Anna

    regulations to control multiple pollutants. The Regional Clean Air Incentives Market (RECLAIM) program). Berlin, Germany: Springer, in press. 1 Introduction Electric power plants emit several different air pollutants, such as carbon dioxide (CO2), sulfur dioxide (SO2), nitrous oxide (NOx), and mercury (Hg

  9. EIS-0066: The Role of Bonneville Power Administration in the Pacific Northwest Power Supply System- including its Participation in a Hydro-Thermal Power Program

    Broader source: Energy.gov [DOE]

    The Bonneville Power Administration (BPA) prepared this EIS to examine the environmental impacts of the Pacific Northwest Power Planning and Conservation Act, which will foster regional electric power planning in the four Northwest states, as well as increase BPA’s authority to address future power needs.

  10. Design, construction and operational results of the IGBT controlled solid state modulator high voltage power supply used in the high power RF systems of the Low Energy Demonstration Accelerator of the accelerator production of tritium (APT) project

    SciTech Connect (OSTI)

    Bradley, J.T. III; Rees, D.; Przeklasa, R.S. [Los Alamos National Lab., NM (United States); Scott, M.C. [Continental Electronics Corp., Dallas, TX (United States)

    1998-12-31T23:59:59.000Z

    The 1700 MeV, 100 mA Accelerator Production of Tritium (APT) Proton Linac will require 244 1 MW, continuous wave RF systems. 1 MW continuous wave klystrons are used as the RF source and each klystron requires 95 kV, 17 A of beam voltage and current. The cost of the DC power supplies is the single largest percentage of the total RF system cost. Power supply reliability is crucial to overall RF system availability and AC to DC conversion efficiency affects the operating cost. The Low Energy Demonstration Accelerator (LEDA) being constructed at Los Alamos National Laboratory (LANL) will serve as the prototype and test bed for APT. The design of the RF systems used in LEDA is driven by the need to field test high efficiency systems with extremely high reliability before APT is built. The authors present a detailed description and test results of one type of advanced high voltage power supply system using Insulated Gate Bipolar Transistors (IGBTs) that has been used with the LEDA High Power RF systems. The authors also present some of the distinctive features offered by this power supply topology, including crowbarless tube protection and modular construction which allows graceful degradation of power supply operation.

  11. Experimental observation of the behaviour of cogenerated dusty plasma using a bipolar pulsed direct current power supply

    SciTech Connect (OSTI)

    Sarkar, Sanjib; Bose, M. [Department of Physics, Jadavpur University, Kolkata 700032 (India); Pramanik, J. [Kharagpur College, Kharagpur 721305, West Bengal (India); Mukherjee, S. [FCIPT, Institute for Plasma Research, Gandhinagar 382428 (India)

    2013-02-15T23:59:59.000Z

    We have experimentally observed the behaviour of cogenerated dusts in unmagnetized plasma produced using a bipolar pulsed dc power supply. In this experiment, the dust particles have been generated through sputtering of graphite cathode and were stratified between two electrodes. This stratification of dust clouds has obtained at a typical range of plasma parameters, namely, 650 V (peak-to-peak) with 0.2 mbar pressure. In above condition, we detected the Taylor-like instability at the interface of two dusty clouds with different densities. A very less dust density (void like) region inside the lesser dust density portion is also noted. Again, it has been observed that a self excited dust density wave propagates towards the higher density dust fluid inside the system as well as a stationary band structure of thin multiple layers of dust particles when we apply a higher voltage (750 V peak-to-peak). The wavelength, phase velocity, and frequency of the excited wave have also been estimated.

  12. Coupling Renewable Energy Supply with Deferrable Demand

    E-Print Network [OSTI]

    Papavasiliou, Anthony

    2011-01-01T23:59:59.000Z

    The lattice model of renewable power supply and real-timerenewable power supply, by formulating a unit commitment model.model that can be used for assessing the impact of integrating renewable power

  13. Proposal for the Award of a Contract for the Supply of 13 kA, 190 V Thyristor Power Converters for the LHC

    E-Print Network [OSTI]

    2003-01-01T23:59:59.000Z

    This document concerns the award of a contract for the supply of nine 13 kA, 190 V thyristor 2-quadrant power converters for the LHC. Following a market survey carried out among 99 firms in nineteen Member States, a call for tenders (IT-2942/SL/LHC) was sent on 25 October 2002 to seven firms in four Member States. By the closing date, CERN had received four tenders from four firms in three Member States. The Finance Committee is invited to agree to the negotiation of a contract with OCEM (IT), the lowest bidder, for the supply of nine 13 kA, 190 V thyristor power converters for a total amount of 2 006 931 Swiss francs, not subject to revision. The firm has indicated the following distribution by country of the contract value covered by this adjudication proposal: IT - 80%; FR - 5%; CH - 5%; Other - 10%.

  14. Proposal to negotiate two blanket purchase contracts, without competitive tendering, for the supply of high-power RF grid-tubes for the CERN accelerators

    E-Print Network [OSTI]

    2005-01-01T23:59:59.000Z

    This document concerns the award of two contracts, without competitive tendering, for the supply of different types of RF high-power grid-tubes (triodes and tetrodes) for the operation of CERN accelerators. For the reasons set out in this document, the Finance Committee is invited to agree to the negotiation of two blanket purchase contracts, without competitive tendering, for the supply of different types of RF high-power grid-tubes (triodes and tetrodes) with: - THALES (FR) for a total amount of 6 800 000 euros (10 540 000 Swiss francs) for a period of five years, subject to revision for inflation from January 2006; - RICHARDSON (DE) for a total amount of 1 100 000 euros (1 705 000 Swiss francs) for a period of five years, subject to revision for inflation from January 2006.

  15. Coupling Renewable Energy Supply with Deferrable Demand

    E-Print Network [OSTI]

    Papavasiliou, Anthony

    2011-01-01T23:59:59.000Z

    systems absorb large amounts of hydroelectric power. Duringthat snow melts and hydroelectric power supply increases andfrom hydroelectric dams or discards renewable power [53].

  16. Proposal for the award of a contract for the supply of four-quadrant switched-mode power converters rated at ± 120, ± 10V for the LHC

    E-Print Network [OSTI]

    2003-01-01T23:59:59.000Z

    This document concerns the award of a contract for the supply of power converters rated at ±120A, ±10V for the LHC. Following a market survey carried out among 147 firms in nineteen Member States, a call for tenders (IT-3037/AB/LHC) was sent on 5 May 2003 to 10 firms and three consortia, each consisting of two firms, in nine Member States. By the closing date, CERN had received nine tenders from nine firms in seven Member States. The Finance Committee is invited to agree to the negotiation of a contract with EFACEC (PT), the lowest conforming bidder after realignment, for the supply of 339 four-quadrant switched-mode power modules and 110 racks for a total amount of 1 652 128 euros (2 534 894 Swiss francs), not subject to revision, with an option for the supply of additional power modules and racks, for a total amount of 142 846 euros (219 171 Swiss francs), subject to revision for inflation from 1 January 2006, bringing the total amount to a maximum of 1 794 974 euros (2 754 065 Swiss francs). The rate of ...

  17. Transformer failure and common-mode loss of instrument power at Nine Mile Point Unit 2 on August 13, 1991

    SciTech Connect (OSTI)

    Not Available

    1991-10-01T23:59:59.000Z

    On August 13, 1991, at Nine Mile Point Unit 2 nuclear power plant, located near Scriba, New York, on Lake Ontario, the main transformer experienced an internal failure that resulted in degraded voltage which caused the simultaneous loss of five uninterruptible power supplies, which in turn caused the loss of several nonsafety systems, including reactor control rod position indication, some reactor power and water indication, control room annunciators, the plant communications system, the plant process computer, and lighting at some locations. The reactor was subsequently brought to a safe shutdown. Following this event, the US Nuclear Regulatory Commission dispatched an Incident Investigation Team to the site to determine what happened, to identify the probable causes, and to make appropriate findings and conclusions. This report describes the incident, the methodology used by the team in its investigation, and presents and the team's findings and conclusions. 59 figs., 14 tabs.

  18. Supply chain dynamics

    E-Print Network [OSTI]

    Barbosa, Ricardo Wagner Lopes, 1976-

    2003-01-01T23:59:59.000Z

    The strong bargaining power of major retailers and the higher requirements for speed, service excellence and customization have significantly contributed to transform the Supply Chain Management. These increasing challenges ...

  19. Study of the pulse power supply unit for the four-horn system of the CERN to Fréjus neutrino super beam

    E-Print Network [OSTI]

    Baussan, E; Dracos, M; Gaudiot, G; Osswald, F; Poussot, P; Vassilopoulos, N; Wurtz, J; Zeter, V

    2013-01-01T23:59:59.000Z

    The power supply studies for the four-horn system for the CERN to Fréjus neutrino Super Beam oscillation experiment are discussed here. The power supply is being studied to meet the physics potential and the mega-watt (MW) power requirements of the proton driver of the Super Beam. A one-half sinusoid current waveform with a 350 kA maximum current and pulse length of 100 \\mu s at 50 Hz frequency is generated and distributed to four-horns. In order to provide the necessary current needed to focus the charged mesons producing the neutrino beam, a bench of capacitors is charged at 50 Hz frequency to a +12 kV reference voltage and then discharged through a large switch to each horn via a set of strip-lines at the same rate. A current recovery stage allows to invert rapidly the negative voltage of the capacitor after the discharging stage in order to recuperate large part of the injected energy and thus to limit the power consuption. The energy recovery efficiency of that system is very high at 97%. For feasibilit...

  20. Proposal for the Purchase, Without a Call for Tenders, of Thyristor Assemblies to be Fitted into the PS Magnet Power Supply as Replacement for the Mercury-Arc Rectifiers

    E-Print Network [OSTI]

    1977-01-01T23:59:59.000Z

    Proposal for the Purchase, Without a Call for Tenders, of Thyristor Assemblies to be Fitted into the PS Magnet Power Supply as Replacement for the Mercury-Arc Rectifiers

  1. Markets to Facilitate Wind and Solar Energy Integration in the Bulk Power Supply: An IEA Task 25 Collaboration; Preprint

    SciTech Connect (OSTI)

    Milligan, M.; Holttinen, H.; Soder, L.; Clark, C.; Pineda, I.

    2012-09-01T23:59:59.000Z

    Wind and solar power will give rise to challenges in electricity markets regarding flexibility, capacity adequacy, and the participation of wind and solar generators to markets. Large amounts of wind power will have impacts on bulk power system markets and electricity prices. If the markets respond to increased wind power by increasing investments in low-capital, high-cost or marginal-cost power, the average price may remain in the same range. However, experiences so far from Denmark, Germany, Spain, and Ireland are such that the average market prices have decreased because of wind power. This reduction may result in additional revenue insufficiency, which may be corrected with a capacity market, yet capacity markets are difficult to design. However, the flexibility attributes of the capacity also need to be considered. Markets facilitating wind and solar integration will include possibilities for trading close to delivery (either by shorter gate closure times or intraday markets). Time steps chosen for markets can enable more flexibility to be assessed. Experience from 5- and 10-minute markets has been encouraging.

  2. Design considerations of a power supply system for fast cycling superconducting accelerator magnets of 2 Tesla b-field generated by a conductor of 100 kA current

    SciTech Connect (OSTI)

    Hays, Steve; Piekarz, Henryk; Pfeffer, Howie; Claypool, Brad; /Fermilab

    2007-06-01T23:59:59.000Z

    Recently proposed fast cycling accelerators for proton drivers (SF-SPS, CERN and SF-MR, SF-BOOSTER, FNAL) neutrino sources require development of new magnet technology. In support of this magnet development a power supply system will need to be developed that can support the high current and high rate of power swing required by the fast cycling (1 sec rise and fall in the SF-MR, 5Hz in Booster). This paper will outline a design concept for a +/- 2000 V and 100,000 A fast ramping power supply system. This power supply design is in support of a 6.44 km magnet system at 0.020 H and 330 m 5 Hz, 0.00534 H superconducting loads. The design description will include the layout and plan for extending the present FNAL Main Injector style ramping power supply to the higher currents needed for this operation. This will also include the design for a harmonic filter and power factor corrector that will be needed to control the large power swings caused by the fast cycle time. A conceptual design for the current regulation system and control will also be outlined. The power circuit design will include the bridge, filter and transformer plan based on existing designs.

  3. Techno-economic analysis of using corn stover to supply heat and power to a corn ethanol plant - Part 2: Cost of heat and power generation systems

    SciTech Connect (OSTI)

    Mani, Sudhagar [University of Georgia; Sokhansanj, Shahabaddine [ORNL; Togore, Sam [U.S. Department of Energy; Turhollow Jr, Anthony F [ORNL

    2010-03-01T23:59:59.000Z

    This paper presents a techno-economic analysis of corn stover fired process heating (PH) and the combined heat and power (CHP) generation systems for a typical corn ethanol plant (ethanol production capacity of 170 dam3). Discounted cash flow method was used to estimate both the capital and operating costs of each system and compared with the existing natural gas fired heating system. Environmental impact assessment of using corn stover, coal and natural gas in the heat and/or power generation systems was also evaluated. Coal fired process heating (PH) system had the lowest annual operating cost due to the low fuel cost, but had the highest environmental and human toxicity impacts. The proposed combined heat and power (CHP) generation system required about 137 Gg of corn stover to generate 9.5 MW of electricity and 52.3 MW of process heat with an overall CHP efficiency of 83.3%. Stover fired CHP system would generate an annual savings of 3.6 M$ with an payback period of 6 y. Economics of the coal fired CHP system was very attractive compared to the stover fired CHP system due to lower fuel cost. But the greenhouse gas emissions per Mg of fuel for the coal fired CHP system was 32 times higher than that of stover fired CHP system. Corn stover fired heat and power generation system for a corn ethanol plant can improve the net energy balance and add environmental benefits to the corn to ethanol biorefinery.

  4. Designing of Hybrid Power Generation System using Wind energy- Photovoltaic Solar energy- Solar energy with Nanoantenna

    E-Print Network [OSTI]

    All the natural wastage energies are used for production of Electricity. Thus, the Electrical Power or Electricity is available with a minimum cost and pollution free to anywhere in the world at all times. This process reveals a unique step in electricity generation and availability from natural resources without hampering the ecological balance. This paper describes a new and evolving Electrical Power Generation System by integrating simultaneously photovoltaic Solar Energy, solar Energy with Nano-antenna, Wind Energy and non conventional energy sources. We can have an uninterrupted power supply irrespective of the natural condition without any sort of environmental pollution. Moreover this process yields the least production cost for electricity generation. Utilization of lightning energy for generation of electricity reveals a new step. The set-up consists of combination of photo-voltaic solar-cell array & Nano-anteena array, a mast mounted wind generator, lead-acid storage batteries, an inverter unit to convert DC power to AC power, electrical lighting loads and electrical heating loads, several fuse and junction boxes and associated wiring, and test instruments for measuring voltages, currents, power factors, and harmonic contamination data throughout the system. This hybrid solar-wind power generating system will extensively use in the Industries and also in external use like home appliance.

  5. A Supply Chain Network Perspective for Electric

    E-Print Network [OSTI]

    Nagurney, Anna

    of New Models "[In recent years] the adequacy of the bulk power transmission system has been challengedA Supply Chain Network Perspective for Electric Power Generation, Supply, Transmission The transformation of the electric power industry from a regulated to a competitive industry In the US, In the EU

  6. Coupling Renewable Energy Supply with Deferrable Demand

    E-Print Network [OSTI]

    Papavasiliou, Anthony

    2011-01-01T23:59:59.000Z

    order: cost comparison for the deep-simple, zero wind,expected wind supply, instead of averaging the cost savingsintegration of wind power. Cost, Utilization, Investment

  7. Effects of the drought on California electricity supply and demand

    E-Print Network [OSTI]

    Benenson, P.

    2010-01-01T23:59:59.000Z

    DEMAND . . . .Demand for Electricity and Power PeakDemand . . • . . ELECTRICITY REQUIREMENTS FOR AGRICULTUREResults . . Coriclusions ELECTRICITY SUPPLY Hydroelectric

  8. Supplying Renewable Energy to Deferrable Loads: Algorithms and Economic Analysis

    E-Print Network [OSTI]

    Oren, Shmuel S.

    in renewable power supply may take hours, lead to additional air pollution, result in wear and the need

  9. OUT Success Stories: Battery Electricity Storage for Quality Power

    SciTech Connect (OSTI)

    Recca, L.

    2000-08-31T23:59:59.000Z

    A 3.5-megawatt valve-regulated lead-acid (VRLA) battery system installed at a lead recycling plant in California provides one hour of energy storage for both peak-shaving and uninterruptible power. It incorporates improvements in battery materials, manufacturing processes, and quality control.

  10. Proposal for the Award of a Contract for the Supply of 13 kA and 20.5 kA, 18 V Switched-Mode Power Converters for the LHC

    E-Print Network [OSTI]

    2003-01-01T23:59:59.000Z

    This document concerns the award of a contract for the supply of 13 kA and 20.5 kA, 18 V switched-mode power converters using sub-converters of 3.25 kA. Following a market survey (MS-2866/SL/LHC) carried out among 81 firms in seventeen Member States and a call for tenders for prototypes (IT-2919/SL/LHC) sent on 11 June 2001, a call for tenders for the supply of the pre-series and series of 13 kA and 20.5 kA, 18 V switched-mode power converters both using sub-converters of 3.25 kA was sent to two firms on 17 September 2002. The Finance Committee is invited to agree to the negotiation of a contract with TRANSTECHNIK (DE), the only firm that has delivered a successfully qualifying prototype, for the supply of eighteen 13 kA and one 20.5 kA, 18 V switched-mode power converters and spares for a total amount of 4 607 731 euros (6 747 300 Swiss francs), not subject to revision. The rate of exchange used is that stipulated in the tender. The firm has indicated the following distribution by country of the contract val...

  11. Why Supply Chain

    E-Print Network [OSTI]

    Datta, Shoumen

    2000-01-01T23:59:59.000Z

    Why supply chain explains the importance of supply chains. It includes an introduction to ERP as designed by SAP.

  12. Bulk Power System Dynamics and Control -VII, August 19-24, 2007, Charleston, South Carolina, USA Dynamics of a Microgrid Supplied by Solid Oxide Fuel Cells1

    E-Print Network [OSTI]

    Hiskens, Ian A.

    Dynamics of a Microgrid Supplied by Solid Oxide Fuel Cells1 Eric M. Fleming Ian A. Hiskens Department-- The paper presents a model for a solid oxide fuel cell (SOFC) stack operating at relatively low pressures. Keywords: Solid oxide fuel cells, microgrid dynamics, inverter control. I. INTRODUCTION Distributed

  13. Power applications of high-temperature superconductivity: Variable speed motors, current switches, and energy storage for end use

    SciTech Connect (OSTI)

    Hawsey, R.A. [Oak Ridge National Lab., TN (United States); Banerjee, B.B.; Grant, P.M. [Electric Power Research Inst., Palo Alto, CA (United States)

    1996-08-01T23:59:59.000Z

    The objective of this project is to conduct joint research and development activities related to certain electric power applications of high-temperature superconductivity (HTS). The new superconductors may allow development of an energy-efficient switch to control current to variable speed motors, superconducting magnetic energy storage (SMES) systems, and other power conversion equipment. Motor types that were considered include induction, permanent magnet, and superconducting ac motors. Because it is impractical to experimentally alter certain key design elements in radial-gap motors, experiments were conducted on an axial field superconducting motor prototype using 4 NbTi magnets. Superconducting magnetic energy storage technology with 0.25--5 kWh stored energy was studied as a viable solution to short duration voltage sag problems on the customer side of the electric meter. The technical performance characteristics of the device wee assembled, along with competing technologies such as active power line conditioners with storage, battery-based uninterruptible power supplies, and supercapacitors, and the market potential for SMES was defined. Four reports were prepared summarizing the results of the project.

  14. 1992 Conversion Resources Supply Document

    SciTech Connect (OSTI)

    Not Available

    1992-03-01T23:59:59.000Z

    In recent years conservation of electric power has become an integral part of utility planning. The 1980 Pacific Northwest Electric Power Planning and Conservation Act (Northwest Power Act) requires that the region consider conservation potential in planning acquisitions of resources to meet load growth. The Bonneville Power Administration (BPA) developed its first estimates of conservation potential in 1982. Since that time BPA has updated its conservation supply analyses as a part of its Resource Program and other planning efforts. Major updates were published in 1985 and in January 1990. This 1992 document presents updated supply curves, which are estimates of the savings potential over time (cumulative savings) at different cost levels of energy conservation measures (ECMs). ECMs are devices, pieces of equipment, or actions that increase the efficiency of electricity use and reduce the amount of electricity used by end-use equipment.

  15. System and method for advanced power management

    DOE Patents [OSTI]

    Atcitty, Stanley (Albuquerque, NM); Symons, Philip C. (Surprise, AZ); Butler, Paul C. (Albuquerque, NM); Corey, Garth P. (Albuquerque, NM)

    2009-07-28T23:59:59.000Z

    A power management system is provided that includes a power supply means comprising a plurality of power supply strings, a testing means operably connected to said plurality of power supply strings for evaluating performance characteristics of said plurality of power supply strings, and a control means for monitoring power requirements and comprising a switching means for controlling switching of said plurality of power supply strings to said testing means.

  16. Using government purchasing power to reduce equipment standby power

    E-Print Network [OSTI]

    Harris, Jeffrey; Meier, Alan; Bartholomew, Emily; Thomas, Alison; Glickman, Joan; Ware, Michelle

    2003-01-01T23:59:59.000Z

    or external power supply, other specifications, and purchasethe consumer to purchase extra power strips and extensionan internal standby power function, shall purchase Although

  17. SUMMER 2007 ELECTRICITY SUPPLY AND DEMAND OUTLOOK

    E-Print Network [OSTI]

    CALIFORNIA ENERGY COMMISSION SUMMER 2007 ELECTRICITY SUPPLY AND DEMAND OUTLOOK DRAFTSTAFFREPORT May ELECTRICITY ANALYSIS OFFICE Sylvia Bender Acting Deputy Director ELECTRICITY SUPPLY ANALYSIS DIVISION B. B assessment of the capability of the physical electricity system to provide power to meet electricity demand

  18. How to Reduce Energy Supply Costs 

    E-Print Network [OSTI]

    Swanson, G.

    2007-01-01T23:59:59.000Z

    customers control their supply-side costs of energy. Specific topics include distributive wind power generation and solid fuel boilers. It identities factors to consider in determining whether these technologies are economically viable for customers...

  19. A Design-Oriented Framework to Determine the Parasitic Parameters of High Frequency Magnetics in Switching Power Supplies using Finite Element Analysis Techniques 

    E-Print Network [OSTI]

    Shadmand, Mohammad

    2012-07-16T23:59:59.000Z

    ____________ This thesis follows the style of IEEE Transactions on Power Electronics. 2 such as multi-winding transformers. More complex geometries indicate that it is almost impossible to derive the analytical equations that describe the behavior of magnetic... is the resistance of the winding, and Cs is the equivalent * Part of this chapter is taken with permission from ?FEA Tool Approach for Determination of Parasitic Capacitance of the Windings in High Frequency Coupled Inductors Filters? in IEEE Power...

  20. Compressed Air Supply Efficiency 

    E-Print Network [OSTI]

    Joseph, B.

    2004-01-01T23:59:59.000Z

    COMPRESSED AIR SUPPLY EFFICENCY Babu Joseph, Ph.D., P.E. Engineer Southern California Edison Irwindale, CA ABSTRACT This project, under contract from California Energy Commission, developed the CASE (Compressed Air Supply Efficiency...

  1. Interactions between Electric-drive Vehicles and the Power Sector in California

    E-Print Network [OSTI]

    McCarthy, Ryan; Yang, Christopher; Ogden, Joan M.

    2009-01-01T23:59:59.000Z

    if supplied with coal power; at emissions rates equal torates). If coal power Electricity GHG emissions rate (gCOlower GHG emissions rates than coal power supplying non-

  2. Power Right. Power Smart. Efficient Computer Power Supplies and Monitors. |

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual Site Environmental Reports Portsmouth Annual SiteAugust 15, 2015Energy

  3. Power network analysis and optimization

    E-Print Network [OSTI]

    Zhang, Wanping

    2009-01-01T23:59:59.000Z

    chip power supply network optimization using multigrid-basedchip decoupling capacitor optimization for high- performanceSapatnekar, “Analysis and optimization of structured power/

  4. Petroleum Supply Monthly

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    adjustments, minus stock change, minus refinery and blender net inputs, minus exports. Net receipts are added as a component of supply at the PAD District level. Crude oil...

  5. Fuel Cells for Backup Power in Telecommunications Facilities (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2009-04-01T23:59:59.000Z

    Telecommunications providers rely on backup power to maintain a constant power supply, to prevent power outages, and to ensure the operability of cell towers, equipment, and networks. The backup power supply that best meets these objectives is fuel cell technology.

  6. Design and Power Management of Energy Harvesting Embedded Systems

    E-Print Network [OSTI]

    Chou, Pai H.

    monitored at a remote location do not readily supply electrical power. Batteries with limited capaci- ties

  7. Highly efficient pulsed power supply system with a two-stage LC generator and a step-up transformer for fast capillary discharge soft x-ray laser at shorter wavelength

    SciTech Connect (OSTI)

    Sakai, Yusuke; Takahashi, Shnsuke; Komatsu, Takanori; Song, Inho; Watanabe, Masato; Hotta, Eiki [Department of Energy Sciences, Tokyo Institute of Technology, 4259-J2-35, Nagatsuta, Midori-ku, Yokohama 226-8502 (Japan)

    2010-01-15T23:59:59.000Z

    Highly efficient and compact pulsed power supply system for a capillary discharge soft x-ray laser (SXRL) has been developed. The system consists of a 2.2 {mu}F two-stage LC inversion generator, a 2:54 step-up transformer, a 3 nF water capacitor, and a discharge section with a few tens of centimeter length capillary. Adoption of the pulsed transformer in combination with the LC inversion generator enables us to use only one gap switch in the circuit for charging the water capacitor up to about 0.5 MV. Furthermore, step-up ratio of a water capacitor voltage to a LC inversion generator initial charging voltage is about 40 with energy transfer efficiency of about 50%. It also leads to good reproducibility of a capillary discharge which is necessary for lasing a SXRL stably. For the study of the possibility of lasing a SXRL at shorter wavelength in a small laboratory scale, high-density and high-temperature plasma column suitable for the laser can be generated relatively easily with this system.

  8. Batteries and electrochemical energy storage are central to any future alternative energy scenario. Future energy generation

    E-Print Network [OSTI]

    Kemner, Ken

    Batteries and electrochemical energy storage are central to any future alternative energy scenario. Future energy generation sources are likely to be intermittent, requiring storage capacity energy storage for uninterrupted power supply units, the electrical grid, and transportation. Of all

  9. Modelling the Role of Software in the Propagation of Failures Across National Critical Infrastructures Chris. W. Johnson

    E-Print Network [OSTI]

    Johnson, Chris

    infrastructures as the uninterruptible power supplies (UPS') that protect mobile phone base stations fail over critical infrastructure. For example, the separation of responsibility for maintaining electricity Infrastructures Chris. W. Johnson Department of Computing Science, University of Glasgow, Scotland, UK, Johnson

  10. www.it.northwestern.edu NorthwesternUniversityInformationTechnology

    E-Print Network [OSTI]

    Shahriar, Selim

    , quickly and efficiently #12;Infrastructure Interconnected system of computers, data applications and services* Data Centers: Secure co-location facilities with uninterrupted power supplies (battery and generator), redundant cooling, and network connectivity in which critical server hardware for systems

  11. Pacific Northwest Power Supply Adequacy Assessment

    E-Print Network [OSTI]

    ), the LOLP rises to about 11 percent. The Council's adequacy assessment only counts existing resources and planned resources that are already sited and licensed for operation in the year assessed. There are other years that is not included in this assessment. #12;3 The Resource Adequacy Standard and What it Means

  12. Research on External Power Supplies Will Save

    E-Print Network [OSTI]

    Office PIER Buildings Energy End-use Efficiency Research Program www.energy.ca.gov in the development of subsequent energy policies. #12;China, Australia, Canada, Brazil and several European

  13. Power supply noise in delay testing

    E-Print Network [OSTI]

    Wang, Jing

    2009-05-15T23:59:59.000Z

    area makes designs more vulnerable to noise problems [17]. Charge sharing is one of the problems that may cause failure in dynamic logic circuits due to their low noise immunity. Charge-sharing noise is produced by charge redistribution between...

  14. External Power Supplies | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed offOCHCO2: Final EnvironmentalCounties,UnitedCommunication,1] Windows212-2012 June 2012and|External

  15. Programmable Power Supply for MST'S Poloidal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's Possible forPortsmouth/Paducah47,193.70 Hg Mercury 35Information &ProgramProgramDOE IEEEINPSS

  16. Improving supply chain resilience

    E-Print Network [OSTI]

    Leung, Elsa Hiu Man

    2009-01-01T23:59:59.000Z

    Due to the global expansion of Company A's supply chain network, it is becoming more vulnerable to many disruptions. These disruptions often incur additional costs; and require time to respond to and recover from these ...

  17. Compressed Air Supply Efficiency

    E-Print Network [OSTI]

    Joseph, B.

    2004-01-01T23:59:59.000Z

    This project, under contract from California Energy Commission, developed the CASE (Compressed Air Supply Efficiency) Index as a stand-alone value for compressor central plant efficiency. This Index captures the overall efficiency of a compressed...

  18. European supply chain study

    E-Print Network [OSTI]

    Puri, Mohitkumar

    2009-01-01T23:59:59.000Z

    Introduction: Supply chain management has been defined as, "..a set of approaches utilized to efficiently integrate suppliers, manufacturers, warehouses and stores, so that merchandise is produced and distributed at the ...

  19. Body powered thermoelectric systems

    E-Print Network [OSTI]

    Settaluri, Krishna Tej

    2012-01-01T23:59:59.000Z

    Great interest exists for and progress has be made in the effective utilization of the human body as a possible power supply in hopes of powering such applications as sensors and continuously monitoring medical devices ...

  20. Risk Management in Biopharmaceutical Supply Chains

    E-Print Network [OSTI]

    Ma, Yao

    2011-01-01T23:59:59.000Z

    Supply Chain Risk Managementof Recent Work on Supply Chain Risk Management . . . . .M. , Supply chain risk management: Outlining an agenda for

  1. Supply chain contract design in supplier- versus buyer-driven channels

    E-Print Network [OSTI]

    Liu, Xingchu

    2006-08-16T23:59:59.000Z

    In the context of supply contract design, the more powerful party has the lib- erty of withholding private information which also improves its bargaining power. Traditionally, the supplier (e.g., manufacturer) has been more powerful, and, hence...

  2. ARES NW Power and Conservation Council Presentation

    E-Print Network [OSTI]

    Shortfall of power, due to high demand, energy supplied into the grid by regenerative braking of shuttle

  3. Petroleum Supply Monthly

    SciTech Connect (OSTI)

    NONE

    1996-02-01T23:59:59.000Z

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  4. Petroleum supply monthly

    SciTech Connect (OSTI)

    NONE

    1995-10-01T23:59:59.000Z

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blends, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  5. GaN power electronics

    E-Print Network [OSTI]

    Lu, Bin

    Between 5 and 10% of the world's electricity is wasted as dissipated heat in the power electronic circuits needed, for example, in computer power supplies, motor drives or the power inverters of photovoltaic systems. This ...

  6. Assessments of long-term uranium supply availability

    E-Print Network [OSTI]

    Zaterman, Daniel R

    2009-01-01T23:59:59.000Z

    The future viability of nuclear power will depend on the long-term availability of uranium. A two-form uranium supply model was used to estimate the date at which peak production will occur. The model assumes a constant ...

  7. MTBE/methanol supply

    SciTech Connect (OSTI)

    Simmons, R.E.

    1986-05-01T23:59:59.000Z

    U.S. methanol production has become economically competitive with imports due to de-escalation of natural gas price from $3.07 mm Btu in January 1985 to $2.07 mm Btu by December 1985. This has reversed the earlier supply outlook when it appeared that additional methanol plants would shutdown due to low cost imports. Current gas cost in conjunction with projections for continued excess supply prompted DuPont to restart their 250 mm gpy plant at Beaumont, Texas. Other former producers are contemplating restarting idle units.

  8. Method and apparatus for improved high power impulse magnetron sputtering

    DOE Patents [OSTI]

    Anders, Andre

    2013-11-05T23:59:59.000Z

    A high power impulse magnetron sputtering apparatus and method using a vacuum chamber with a magnetron target and a substrate positioned in the vacuum chamber. A field coil being positioned between the magnetron target and substrate, and a pulsed power supply and/or a coil bias power supply connected to the field coil. The pulsed power supply connected to the field coil, and the pulsed power supply outputting power pulse widths of greater that 100 .mu.s.

  9. Natural Gas Supply SBIR Program

    SciTech Connect (OSTI)

    Shoemaker, H.D.; Gwilliam, W.J.

    1995-07-01T23:59:59.000Z

    The Small Business Innovation Research (SBIR) program was created in 1982 by Public Law 97-219 and reauthorized in 1992 until the year 2000 by Public Law 102-564. The purposes of the new law are to (1) expand and improve the SBIR program, 2) emphasize the program`s goal of increasing private sector commercialization of technology developed through Federal R&D, (3) increase small business participation in Federal R&D, and (4) improve the Federal Government`s dissemination of information concerning the SBIR program. DOE`s SBIR pro-ram has two features that are unique. In the 1995 DOE SBIR solicitation, the DOE Fossil Energy topics were: environmental technology for natural gas, oil, and coal; advanced recovery of oil; natural gas supply; natural gas utilization; advanced coal-based power systems; and advanced fossil fuels research. The subtopics for this solicitation`s Natural Gas Supply topic are (1) drilling, completion, and stimulation; (2) low-permeability Formations; (3) delivery and storage; and (4) natural gas upgrading.

  10. Power Droop Testing Ilia Polian1

    E-Print Network [OSTI]

    Polian, Ilia

    Power Droop Testing Ilia Polian1 Alejandro Czutro1 Sandip Kundu2 Bernd Becker1 1 Albert sudden drop or rise in power supply voltage. This change is known as power droop and is an instance of power supply noise. Although power droop may cause an IC to fail, such failures cannot currently

  11. GSA Wind Supply Opportunity

    Broader source: Energy.gov (indexed) [DOE]

    supplier to take the Walnut Ridge electricity and blend it with other system and block purchase power for delivery to our buildings. *For power put into the grid in one place...

  12. A NEW, RUGGED, HIGH POWER COCKCROFT-WALTON POWER SUPPLY

    E-Print Network [OSTI]

    Hinkson, J.

    2010-01-01T23:59:59.000Z

    C = 10-20 pf 8. The load induced droop AV = I/fC x N/3 (2N +1). This is voltage droop that w i l l occur with a D load Ccapability to correct for the droop. With a pulsed load the

  13. CREATING THE NORTHEAST GASOLINE SUPPLY RESERVE

    Broader source: Energy.gov [DOE]

    In 2012, Superstorm Sandy made landfall in the northeastern United States and caused heavy damage to two refineries and left more than 40 terminals in New York Harbor closed due to water damage and loss of power. This left some New York gas stations without fuel for as long as 30 days. As part of the Obama Administration’s ongoing response to the storm, the Department of Energy created the first federal regional refined product reserve, the Northeast Gasoline Supply Reserve.

  14. Modeling of Supply Chain Risk under Disruptions with Performance Measurement and Robustness

    E-Print Network [OSTI]

    Nagurney, Anna

    and logistical networks, to transportation networks, to electric power networks, financial networks, Nagurney, Dong Vulnerabilities of Supply Chain Networks #12;This presentation is based on the paper with the same title in Managing Supply Chain Risk and Vulnerability: Tools and Methods for Supply Chain Decision

  15. Modeling Generator Power Plant Portfolios and Pollution Taxes

    E-Print Network [OSTI]

    Nagurney, Anna

    Modeling Generator Power Plant Portfolios and Pollution Taxes in Electric Power Supply Chain;Modeling Energy Taxes and Credits: The Genco's Choice · Each Genco has a portfolio of power plants · Each power plant can have different supply costs and transaction costs · Supply costs can reflect capital

  16. Fiber Supply Associate Company Overview

    E-Print Network [OSTI]

    Mazzotti, Frank

    materials acquisition, harvesting, logistics coordination, contract negotiations, and inventory management, Purchasing, Industrial Engineering, Operations management, Materials Management, Supply Chain) Authorized leadership roles such as Fiber Specialist, Fiber Supply Manager, Region Manager, Director, General Manager

  17. NAPS 2003, 35th North American Power Symposium, University of Missouri-Rolla in Rolla, Missouri, October 20-21, 2003. pp. 559-566. Abstract--Security of supply has been always a key factor

    E-Print Network [OSTI]

    Catholic University of Chile (Universidad Católica de Chile)

    as a terrorist attack to some key power plants or transmission lines. Since September 11, 2001 the threat three kinds of threats over society: a) Attacks upon the power system. Here the target is the electricNAPS 2003, 35th North American Power Symposium, University of Missouri-Rolla in Rolla, Missouri

  18. Competition in Electricity Supply: will "1998" be worth it?

    E-Print Network [OSTI]

    California at Berkeley. University of

    PWP-057 Competition in Electricity Supply: will "1998" be worth it? Richard Green and Tanga McDaniel May 1998 This paper is part of the working papers series of the Program on Workable Energy Regulation (POWER). POWER is a program of the University of California Energy Institute, a multicampus research unit

  19. Petroleum Supply Monthly

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 111 1,613 122Commercial Consumers (NumberThousandby thePricePricetheTable 1. U.S. Supply,

  20. Robust SAT-Based Search Algorithm for Leakage Power Reduction

    E-Print Network [OSTI]

    Aloul, Fadi

    , including packaging and cooling costs, battery life in portable systems, and power supply grid design scaling of the supply voltage (Vdd) by 30% promises to reduce the power by 50% [4]. Such supply voltage a high NMOS or PMOS transistor to shut off the supply to low logic [9]. This approach results in very

  1. Heat Supply Who What Where and -Why

    E-Print Network [OSTI]

    Columbia University

    ................................................. 6 District-heating (DH) supply: key figures .............................. 6 What is biomass Geothermics ..........................................................................11 Waste for heat supplyHeat Supply in Denmark Who What Where and - Why #12;Title: Heat Supply in Denmark - Who What Where

  2. NNSA TRITIUM SUPPLY CHAIN

    SciTech Connect (OSTI)

    Wyrick, Steven [Savannah River National Laboratory, Aiken, SC, USA; Cordaro, Joseph [Savannah River National Laboratory, Aiken, SC, USA; Founds, Nanette [National Nuclear Security Administration, Albuquerque, NM, USA; Chambellan, Curtis [National Nuclear Security Administration, Albuquerque, NM, USA

    2013-08-21T23:59:59.000Z

    Savannah River Site plays a critical role in the Tritium Production Supply Chain for the National Nuclear Security Administration (NNSA). The entire process includes: • Production of Tritium Producing Burnable Absorber Rods (TPBARs) at the Westinghouse WesDyne Nuclear Fuels Plant in Columbia, South Carolina • Production of unobligated Low Enriched Uranium (LEU) at the United States Enrichment Corporation (USEC) in Portsmouth, Ohio • Irradiation of TPBARs with the LEU at the Tennessee Valley Authority (TVA) Watts Bar Reactor • Extraction of tritium from the irradiated TPBARs at the Tritium Extraction Facility (TEF) at Savannah River Site • Processing the tritium at the Savannah River Site, which includes removal of nonhydrogen species and separation of the hydrogen isotopes of protium, deuterium and tritium.

  3. Sustainable Biomass Supply Systems

    SciTech Connect (OSTI)

    Erin Searcy; Dave Muth; Erin Wilkerson; Shahab Sokansanj; Bryan Jenkins; Peter Titman; Nathan Parker; Quinn Hart; Richard Nelson

    2009-04-01T23:59:59.000Z

    The U.S. Department of Energy (DOE) aims to displace 30% of the 2004 gasoline use (60 billion gal/yr) with biofuels by 2030 as outlined in the Energy Independence and Security Act of 2007, which will require 700 million tons of biomass to be sustainably delivered to biorefineries annually. Lignocellulosic biomass will make an important contribution towards meeting DOE’s ethanol production goals. For the biofuels industry to be an economically viable enterprise, the feedstock supply system (i.e., moving the biomass from the field to the refinery) cannot contribute more that 30% of the total cost of the biofuel production. The Idaho National Laboratory in collaboration with Oak Ridge National Laboratory, University of California, Davis and Kansas State University are developing a set of tools for identifying economical, sustainable feedstocks on a regional basis based on biorefinery siting.

  4. Power Quality Implications

    E-Print Network [OSTI]

    Hilson, D.

    Electric utilities in the United States spend in excess of one billion dollars annually to maintain or improve the quality of electric power supplied to their customers. Yet, an increasing and alarming number of complaints are being voiced...

  5. 194 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 56, NO. 1, JANUARY 2009 PWM Method to Eliminate Power Sources in a

    E-Print Network [OSTI]

    Catholic University of Chile (Universidad Católica de Chile)

    unidirectional if the machine is not using regenerative braking. In this paper, these nine power supplies

  6. Limiting the Power Consumption of Main Memory Bruno Diniz, Dorgival Guedes,

    E-Print Network [OSTI]

    Bianchini, Ricardo

    their power supply, packaging, and cooling requirements. When the peak power consumption is high, the hardware- than-peak power budget, based on which power supply, packaging, and cooling infrastructures can be more, the power supply, packag- ing, and cooling infrastructures of these components and systems are becoming

  7. Industry Supply Chain Development (Ohio)

    Broader source: Energy.gov [DOE]

    Supply Chain Development programs are focused on targeted industries that have significant growth opportunities for Ohio's existing manufacturing sector from emerging energy resources and...

  8. Tariffs with Dynamic Supply Response

    E-Print Network [OSTI]

    Karp, Larry

    1985-01-01T23:59:59.000Z

    Giannini FDN iibrary TARIFFS WITH DYNAMIC SUPPLY RESWNSEpaper studies the optimal tariff in a dynamic framework. Thesellers, the optimal tariff is dynam- ically inconsistent;

  9. Interactions between Electric-drive Vehicles and the Power Sector in California

    E-Print Network [OSTI]

    McCarthy, Ryan; Yang, Christopher; Ogden, Joan M.

    2009-01-01T23:59:59.000Z

    plants in California and 1195 power plants collectively inutilities within California. Those power plants are mostly16] California electricity supply in The mix of power plants

  10. WATER SUPPLY A Handbook on

    E-Print Network [OSTI]

    US Army Corps of Engineers

    WATER SUPPLY HANDBOOK A Handbook on Water Supply Planning and Resource Management Institute for Water Resources Water Resources Support Center U.S. Army Corps of Engineers 7701 Telegraph Road Studies Division December 1998 Revised IWR Report 96-PS-4 #12;U.S. Army Institute for Water Resources

  11. REGIONAL WATER SUPPLY PLANNING AND

    E-Print Network [OSTI]

    Mays, Larry W.

    CHAPTER 3 REGIONAL WATER SUPPLY PLANNING AND CAPACITY EXPANSION MODELS Messele Z. Ejeta California Department of Water Resources Sacramento, California Larry W. Mays Department of Civil and Environmental Engineering Arizona State University Tempe, Arizona 3.1 INTRODUCTION Water supply planning on a regional scale

  12. GLOBAL WOOD SUPPLY Sten Nilsson

    E-Print Network [OSTI]

    GLOBAL WOOD SUPPLY Sten Nilsson Biomass and Resource Efficiency: the need for a supply led approach the wood come from? Western EU Deficit Eastern EU Deficit Rest of Eastern Europe Balanced Russia Rest of Eastern Europe Balanced Russia Is probably at production ceiling under current conditions Japan

  13. Petroleum Supply Monthly, September 1984

    SciTech Connect (OSTI)

    Not Available

    1984-11-01T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for September 1984. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. The focus article discusses EIA data series for crude oil imports, motor gasoline supplied, and distillate and residual fuel oil supplied, as well as crude oil production. A companion article, An Evaluation of Crude Oil Production Statistics beginning on page xvii compares crude oil production volumes reported in EIA's petroleum supply publications with those shown in state reports.

  14. Petroleum supply monthly, August 1993

    SciTech Connect (OSTI)

    Not Available

    1993-09-01T23:59:59.000Z

    This publication the Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report, (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. Data presented are divided into Summary Statistics and Detailed Statistics.

  15. Lab school supply drive starts July 15

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh SchoolIn12electron 9 5 - -/e),,s -Labgrants DecisionLab school supply

  16. Reducing Power Load Fluctuations on Ships Using Power Redistribution Control

    E-Print Network [OSTI]

    Johansen, Tor Arne

    controller is demonstrated through simulation studies on a supply vessel power plant, using the SIMULINK plant with electric propulsion, the power generation will con- sist of multiple engines, whereReducing Power Load Fluctuations on Ships Using Power Redistribution Control Damir Radan,1 Asgeir J

  17. A Tariff for Reactive Power - IEEE

    SciTech Connect (OSTI)

    Kueck, John D [ORNL; Tufon, Christopher [Pacific Gas and Electric Company; Isemonger, Alan [California Independent System Operator; Kirby, Brendan J [ORNL

    2008-11-01T23:59:59.000Z

    This paper describes a suggested tariff or payment for the local supply of reactive power from distributed energy resources. The authors consider four sample customers, and estimate the cost of supply of reactive power for each customer. The power system savings from the local supply of reactive power are also estimated for a hypothetical circuit. It is found that reactive power for local voltage regulation could be supplied to the distribution system economically by customers when new inverters are installed. The inverter would be supplied with a power factor of 0.8, and would be capable of local voltage regulation to a schedule supplied by the utility. Inverters are now installed with photovoltaic systems, fuel cells and microturbines, and adjustable-speed motor drives.

  18. The Strategic Computing Complex The Strategic Computing Complex (SCC) at the Los Alamos

    E-Print Network [OSTI]

    power supplies, or RUPS, which allow for efficient, uninterrupted power use and rapid recovery in cases of power loss. This power runs the facility and supercomputers, as well as the building's cooling system. The computer room is air-cooled, where 84 air-conditioning work push 1.5 million cubic feet of chilled air from

  19. Improve supply chain resilience by multi-stage supply chain

    E-Print Network [OSTI]

    Xu, Jie, M. Eng. Massachusetts Institute of Technology

    2009-01-01T23:59:59.000Z

    Due to the global expansion of Company A's supply chain network, it is becoming more vulnerable to many disruptions. These disruptions often incur additional costs; and require time to respond to and recover from these ...

  20. Improving supply chain resilience by multi-stage supply chain

    E-Print Network [OSTI]

    Yang, Jingxia, M. Eng, Massachusetts Institute of Technology

    2009-01-01T23:59:59.000Z

    Due to the global expansion of Company A's supply chain network, it is becoming more vulnerable to many disruptions. These disruptions often incur additional costs; and require time to respond to and recover from these ...

  1. Water supply and demand in an energy supply model

    SciTech Connect (OSTI)

    Abbey, D; Loose, V

    1980-12-01T23:59:59.000Z

    This report describes a tool for water and energy-related policy analysis, the development of a water supply and demand sector in a linear programming model of energy supply in the United States. The model allows adjustments in the input mix and plant siting in response to water scarcity. Thus, on the demand side energy conversion facilities can substitute more costly dry cooling systems for conventional evaporative systems. On the supply side groundwater and water purchased from irrigators are available as more costly alternatives to unappropriated surface water. Water supply data is developed for 30 regions in 10 Western states. Preliminary results for a 1990 energy demand scenario suggest that, at this level of spatial analysis, water availability plays a minor role in plant siting. Future policy applications of the modeling system are discussed including the evaluation of alternative patterns of synthetic fuels development.

  2. Petroleum supply monthly, February 1994

    SciTech Connect (OSTI)

    Not Available

    1994-03-01T23:59:59.000Z

    The Petroleum Supply Monthly presents data describing the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders; operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. Data are divided into two sections: Summary statistics and Detailed statistics.

  3. Petroleum supply monthly, April 1994

    SciTech Connect (OSTI)

    Not Available

    1994-04-01T23:59:59.000Z

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographical regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US.

  4. SOLVING POWER-CONSTRAINED GAS TRANSPORTATION ...

    E-Print Network [OSTI]

    2014-11-27T23:59:59.000Z

    Nov 27, 2014 ... physical quantities but further incorporate heat power supplies and .... consist of pipes Api, resistors Ars, valves Ava, control valves Acv, and ...

  5. City of Boulder- Green Power Purchasing

    Broader source: Energy.gov [DOE]

    The City of Boulder purchases a portion of its electricity supply from wind power through Xcel Energy's Windsource program and Renewable Choice Energy, headquartered in Colorado. Boulder purchases...

  6. LNG links remote supplies and markets

    SciTech Connect (OSTI)

    Avidan, A.A.; Gardner, R.E.; Nelson, D.; Borrelli, E.N. [Mobil LNG Inc., Houston, TX (United States); Rethore, T.J. [Arthur D. Little Inc., Houston, TX (United States)

    1997-06-02T23:59:59.000Z

    Liquefied natural gas (LNG) has established a niche for itself by matching remote gas supplies to markets that both lacked indigenous gas reserves and felt threatened in the aftermath of the energy crises of the 1970s and 1980s. It has provided a cost-effective energy source for these markets, while also offering an environmentally friendly fuel long before that was fashionable. The introduction of natural-gas use via LNG in the early years (mostly into France and Japan) has also allowed LNG to play a major role in developing gas infrastructure. Today, natural gas, often supplied as LNG, is particularly well-suited for use in the combined cycle technology used in independent power generation projects (IPPs). Today, LNG players cannot simply focus on monetizing gas resources. Instead, they must adapt their projects to meet the needs of changing markets. The impact of these changes on the LNG industry has been felt throughout the value chain from finding and producing gas, gas treatment, liquefaction, transport as a liquid, receiving terminals and regasification, and finally, to consumption by power producers, industrial users, and households. These factors have influenced the evolution of the LNG industry and have implications for the future of LNG, particularly in the context of worldwide natural gas.

  7. The 3He Supply Problem

    SciTech Connect (OSTI)

    Kouzes, Richard T.

    2009-05-01T23:59:59.000Z

    One of the main uses for 3He is in gas proportional counters for neutron detection. Radiation portal monitors deployed for homeland security and non-proliferation use such detectors. Other uses of 3He are for research detectors, commercial instruments, well logging detectors, dilution refrigerators, for targets or cooling in nuclear research, and for basic research in condensed matter physics. The US supply of 3He comes almost entirely from the decay of tritium used in nuclear weapons by the US and Russia. A few other countries contribute a small amount to the world’s 3He supply. Due to the large increase in use of 3He for homeland security, the supply has dwindled, and can no longer meet the demand. This white paper reviews the problems of supply, utilization, and alternatives.

  8. Effective contracts in supply chains

    E-Print Network [OSTI]

    Shum, Wanhang

    2007-01-01T23:59:59.000Z

    In the past decade, we have seen significant increase in the level of outsourcing in many industries. This increase in the level of outsourcing increases the importance of implementing effective contracts in supply chains. ...

  9. Grand Challenges and Opportunities Supply Chain Network Analysis to Design

    E-Print Network [OSTI]

    Boyer, Edmond

    International Conference on Network Games, Control, and Optimization Paris, France October 12-14, 2011 Anna and backbones for the production, distribution, and consumption of goods as well as services in our globalized of Supply Chains food and food products high tech products automotive energy (oil, electric power, etc

  10. Design of a 50-watt air supplied turbogenerator

    E-Print Network [OSTI]

    Jovanovic, Stevan, S.M. Massachusetts Institute of Technology

    2008-01-01T23:59:59.000Z

    This thesis presents the design of a high-pressure-ratio, low-flow turbogenerator with 50 W electrical power output, designed to operate from a 5-bar air supply. The research shows that a MEMS-based silicon turbine in ...

  11. THE ECONOMICS OF CONSERVED-ENERGY "SUPPLY" CURVES

    E-Print Network [OSTI]

    California at Berkeley. University of

    is part of the working papers series of the Program on Workable Energy Regulation (POWER). POWERPWP-028 THE ECONOMICS OF CONSERVED-ENERGY "SUPPLY" CURVES Steven Stoft April 1995 This paper is a program of the University of California Energy Institute, a multicampus research unit of the University

  12. Modeling Generator Power Plant Portfolios and Pollution Taxes in

    E-Print Network [OSTI]

    Nagurney, Anna

    Modeling Generator Power Plant Portfolios and Pollution Taxes in Electric Power Supply Chain-term solution (e.g.,are long-term solution (e.g., solar power and wind power (solar power and wind power Heavy user of fossil fuels:Heavy user of fossil fuels: Electric power industryElectric power industry

  13. Environmental decision making: supply-chain considerations

    E-Print Network [OSTI]

    Reich-Weiser, Corinne; Dornfeld, David

    2008-01-01T23:59:59.000Z

    manufacturing environmental impact and enable the reductionthe supply chain (3) environmental impact and cost must bethe supply chain’s environmental impact and flexibility (

  14. Supplying High-Quality, Raw Biomass

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Supplying High-Quality, Raw Biomass The building blocks to supply high-quality raw biomass start with harvesting and collection practices, product storage and recommendations of...

  15. Supply Voltage Degradation Aware Analytical Placement Andrew B. Kahng Bao Liu Qinke Wang

    E-Print Network [OSTI]

    Liu, Bao

    Supply Voltage Degradation Aware Analytical Placement Andrew B. Kahng Bao Liu Qinke Wang Computer@cs.ucsd.edu} Abstract Increasingly significant power/ground supply voltage degradation in nanometer VLSI designs leads to system per- formance degradation and even malfunction. Existing tech- niques focus on design

  16. Estimating business and residential water supply interruption losses from catastrophic events

    E-Print Network [OSTI]

    Sunding, David

    . In particular, studies have focused on water supply, electric power, and transportation infrastructure [Chang and spatial extent, water supply infrastructure in many urban areas is particularly vulnerable to interruption and residential lifeline users. As a result, the total economic losses caused by infrastructure damage may be much

  17. Optimize the Supply Air Temperature Reset Schedule for a Single-Duct VAV System

    E-Print Network [OSTI]

    Wei, G.; Claridge, D. E.; Liu, M.

    2000-01-01T23:59:59.000Z

    to electrical power, etc. The influence of those parameters on optimal supply air temperature reset schedules has been briefly evaIuated in this paper. System operators should keep these factors in mind when they develop the optimal supply air temperature...

  18. Petroleum supply monthly, July 1994

    SciTech Connect (OSTI)

    Not Available

    1994-07-26T23:59:59.000Z

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  19. Petroleum supply monthly, June 1994

    SciTech Connect (OSTI)

    Not Available

    1994-06-28T23:59:59.000Z

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  20. Petroleum supply monthly, September 1991

    SciTech Connect (OSTI)

    Not Available

    1991-09-30T23:59:59.000Z

    The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administrations for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics. 65 tabs.

  1. Petroleum supply monthly, January 1996

    SciTech Connect (OSTI)

    NONE

    1996-02-15T23:59:59.000Z

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  2. SCC The Strategic Computing Complex The Strategic Computing Complex (SCC) at the Los Alamos

    E-Print Network [OSTI]

    megawatts of power--more than the town of Los Alamos.The SCC utilizes rotary uninterruptible power supplies.This power runs the facility and supercomputers, as well as the building's cooling system.The computer room is air-cooled, where 84 air-conditioning work push 1.5 million cubic feet of chilled air from

  3. Trans-Atlantic Fuel Fabrication Security of Supply Program

    SciTech Connect (OSTI)

    Bobo Perez, Emilio I. [ENUSA Industrias Avanzadas, S.A., Santiago Rusinol 12, 28040 Madrid (Spain); Novo Sanjurjo, Manuel [CC.NN. Almaraz-Trillo, AIE, Avenida de Manoteras, 46 bis, Edificio Delta Norte, 3 planta 5a, 28050 - Madrid (Spain); Ferguson, Scott [Wolf Creek Nuclear Operating Corporation, Wolf Creek Generating Station, Post Office Box 411, Burlington, KS 66839 (United States); Feagin, Bob; Dwight, James [Westinghouse Electric Company LLC, P.O. Drawer R, Columbia, South Carolina 29250 (United States); Gonzalez Villegas, Roberto [ENUSA Industrias Avanzadas, S.A., Santiago Rusinol 12, 28040 Madrid (Spain)

    2007-07-01T23:59:59.000Z

    The present paper describes one of the latest initiatives put in place by the nuclear industry to secure the supply of nuclear fuel for LWR. The project presented here is focused on the manufacturing phase of the supply chain and is the result of a cooperation between US and Spanish entities - nuclear power plant as well as fuel manufacturers - with the added value of the participation of other facilities located in Europe. The main objectives, challenges and characteristics of the program are discussed as well as the expected results. (authors)

  4. Optimal Green Energy Utilization in MIMO Systems with Hybrid Energy Supplies

    E-Print Network [OSTI]

    1 Optimal Green Energy Utilization in MIMO Systems with Hybrid Energy Supplies Congshi Hu, Jie Gong, it is feasible for BSs to be powered by green energy, such as solar energy and wind energy. For instance

  5. Battery-Powered Digital CMOS Massoud Pedram

    E-Print Network [OSTI]

    Pedram, Massoud

    (submarines) Stationary batteries 250 Wh~5 MWh Emergency power supplies, local energy storage, remote relay1 Page 1 USC Low Power CAD Massoud Pedram Battery-Powered Digital CMOS Design Massoud Pedram Power CAD Massoud Pedram Motivation Extending the battery service life of battery-powered micro

  6. Fuel-cell based power generating system having power conditioning apparatus

    DOE Patents [OSTI]

    Mazumder, Sudip K. (Chicago, IL); Pradhan, Sanjaya K. (Des Plaines, IL)

    2010-10-05T23:59:59.000Z

    A power conditioner includes power converters for supplying power to a load, a set of selection switches corresponding to the power converters for selectively connecting the fuel-cell stack to the power converters, and another set of selection switches corresponding to the power converters for selectively connecting the battery to the power converters. The power conveners output combined power that substantially optimally meets a present demand of the load.

  7. Petroleum supply monthly, August 1994

    SciTech Connect (OSTI)

    Not Available

    1994-08-26T23:59:59.000Z

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  8. International Oil Supplies and Demands

    SciTech Connect (OSTI)

    Not Available

    1992-04-01T23:59:59.000Z

    The eleventh Energy Modeling Forum (EMF) working group met four times over the 1989--1990 period to compare alternative perspectives on international oil supplies and demands through 2010 and to discuss how alternative supply and demand trends influence the world's dependence upon Middle Eastern oil. Proprietors of eleven economic models of the world oil market used their respective models to simulate a dozen scenarios using standardized assumptions. From its inception, the study was not designed to focus on the short-run impacts of disruptions on oil markets. Nor did the working group attempt to provide a forecast or just a single view of the likely future path for oil prices. The model results guided the group's thinking about many important longer-run market relationships and helped to identify differences of opinion about future oil supplies, demands, and dependence.

  9. Petroleum supply monthly, July 1993

    SciTech Connect (OSTI)

    Not Available

    1993-07-29T23:59:59.000Z

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: Petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  10. Petroleum Supply Monthly, May 1985

    SciTech Connect (OSTI)

    Not Available

    1985-07-01T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products through May, 1985. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. This issue features a ''Mid-Year Petroleum Review'', beginning on page xiii and focusing on major petroleum supply developments in the first half of 1985 and the outlook for the remainder of the year. The article discusses changes in consumption, domestic crude oil production, refinery operations, foreign trade, stocks (including the Strategic Petroleum Reserve) and prices. 33 tabs.

  11. Petroleum supply monthly, July 1984

    SciTech Connect (OSTI)

    Not Available

    1984-09-01T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for July 1984. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. This issue also presents IEA's winter 1984-1985 distillate fuel outlook and an overview of distillate fuel oil. These articles focus on the respective roles of production, imports, and stocks in meeting distillage fuel oil demand. Regional supply patterns, especially for the East Coast are also discussed. 33 tables. (DMC)

  12. International Oil Supplies and Demands

    SciTech Connect (OSTI)

    Not Available

    1991-09-01T23:59:59.000Z

    The eleventh Energy Modeling Forum (EMF) working group met four times over the 1989--90 period to compare alternative perspectives on international oil supplies and demands through 2010 and to discuss how alternative supply and demand trends influence the world's dependence upon Middle Eastern oil. Proprietors of eleven economic models of the world oil market used their respective models to simulate a dozen scenarios using standardized assumptions. From its inception, the study was not designed to focus on the short-run impacts of disruptions on oil markets. Nor did the working group attempt to provide a forecast or just a single view of the likely future path for oil prices. The model results guided the group's thinking about many important longer-run market relationships and helped to identify differences of opinion about future oil supplies, demands, and dependence.

  13. Pool power control in remelting systems

    DOE Patents [OSTI]

    Williamson, Rodney L. (Albuquerque, NM); Melgaard, David K. (Albuquerque, NM); Beaman, Joseph J. (Austin, TX)

    2011-12-13T23:59:59.000Z

    An apparatus for and method of controlling a remelting furnace comprising adjusting current supplied to an electrode based upon a predetermined pool power reference value and adjusting the electrode drive speed based upon the predetermined pool power reference value.

  14. Microsoft PowerPoint - NRELFeb2009

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    y gy g 6 Solar power Beginning in 2004, RMOTC and NREL partnered to test the use of solar panels in the oil field. The panels supplied power to a fluid transfer pump used in...

  15. Modeling water use at thermoelectric power plants

    E-Print Network [OSTI]

    Rutberg, Michael J. (Michael Jacob)

    2012-01-01T23:59:59.000Z

    The withdrawal and consumption of water at thermoelectric power plants affects regional ecology and supply security of both water and electricity. The existing field data on US power plant water use, however, is of limited ...

  16. EIS-0076: Bonneville Power Administration Alumax

    Broader source: Energy.gov [DOE]

    The Bonneville Power Administration (BPA) developed this EIS for the proposed Alumax primary aluminum reduction plant to determine the environmental, economic and social impacts of plant construction, as well as potential power supply alternatives for BPA.

  17. Assessing Reliability in Energy Supply Systems

    E-Print Network [OSTI]

    McCarthy, Ryan; Ogden, Joan M.; Sperling, Dan

    2008-01-01T23:59:59.000Z

    total of 15 metrics. Pathway reliability General objectives Adequacy Security Functional zones Primary energy supply

  18. Assessing reliability in energy supply systems

    E-Print Network [OSTI]

    McCarthy, Ryan W.; Ogden, Joan M.; Sperling, Daniel

    2007-01-01T23:59:59.000Z

    total of 15 metrics. Pathway reliability General objectives Adequacy Security Functional zones Primary energy supply

  19. CALCULATING THE CARBON FOOTPRINT SUPPLY CHAIN FOR

    E-Print Network [OSTI]

    Su, Xiao

    CALCULATING THE CARBON FOOTPRINT SUPPLY CHAIN FOR THE SEMICONDUCTOR INDUSTRY By: Yasser Dessouky #12;Carbon Footprint Supply Chain Carbon Trust defines carbon footprint of a supply chain as follows: "The carbon footprint of a product is the carbon dioxide emitted across the supply chain for a single

  20. Petroleum supply monthly, January 1994

    SciTech Connect (OSTI)

    Not Available

    1994-01-01T23:59:59.000Z

    Data presented describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  1. Petroleum Supply Monthly, March 1985

    SciTech Connect (OSTI)

    Not Available

    1985-05-01T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for March 1985. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. 13 figs., 33 tabs.

  2. Petroleum Supply Monthly, April 1985

    SciTech Connect (OSTI)

    Not Available

    1985-06-01T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products through April, 1985. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks.

  3. Petroleum Supply Monthly, October 1984

    SciTech Connect (OSTI)

    Not Available

    1984-12-01T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for October 1984. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administraction for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks.

  4. Document Supply Services Quick Guide

    E-Print Network [OSTI]

    , phrase, ISBN/ISSN in the Search Term field (other options are available in the dropdown menu). Note1 Document Supply Services Quick Guide The DSS Portal makes requesting easy! Search for your item and password. If you are having difficulty please read the login help on the main DSS webpage. 2. Enter a word

  5. CMOS RF Power Amplifier Design for Wireless Communications

    E-Print Network [OSTI]

    FANG, Qiang

    2012-01-01T23:59:59.000Z

    conjugate (S22) match (solid curve) and power match (dashedSupply Linear RF Power Amplifier", IEEE J. Solid-State Circ.Fully-integrated CMOS Power Amplifiers", IEEE J. Solid-State

  6. Bonneville Power Administration Overview As of December 1, 2014

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    80% of BPA's total firm power supply is carbon emission-free hydroelectric power * BPA's grid provides about 75% of the bulk transmission capacity in the Region Bonneville Power...

  7. Petroleum supply monthly, March 1994

    SciTech Connect (OSTI)

    Not Available

    1994-03-30T23:59:59.000Z

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. Most time series include preliminary estimates for one month based on the Weekly Petroleum Supply Reporting System; statistics based on the most recent data from the Monthly Petroleum Supply Reporting System (MPSRS); and statistics published in prior issues of the PSM and PSA. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas -- the United States (50 States and the District of Columbia), five PAD Districts, and 12 Refining Districts. At the US and PAD District level, the total volume and the daily rate of activities are presented. The statistics are developed from monthly survey forms submitted by respondents to the EIA and from data provided from other sources.

  8. Petroleum supply monthly, June 1993

    SciTech Connect (OSTI)

    Not Available

    1993-06-28T23:59:59.000Z

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures ih the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. Most time series include preliminary estimates for one month based on the Weekly Petroleum Supply Reporting System; statistics based on the most recent data from the Monthly Petroleum Supply Reporting System (MPSRS); and statistics published in prior issues of the PSM and PSA. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas - - the United States (50 States and the District of Columbia), five PAD Districts, and 12 Refining Districts. At the US and PAD District level, the total volume and the daily rate of activities are presented. The statistics are developed from monthly survey forms submitted by respondents to the EIA and from data provided firom other sources.

  9. Quantitative assessment of proposals on assurance of nuclear fuel supply

    SciTech Connect (OSTI)

    Tanaka, T.; Kuno, Y.; Tanaka, S. [University of Tokyo, 7-3-1 Hongou, Bunkyou-ku, Tokyo 112-0005 (Japan)

    2013-07-01T23:59:59.000Z

    The assurance of nuclear fuel supply has the potential to contribute to balancing peaceful use of nuclear power and nuclear nonproliferation. 5 proposals which provide the backup supply of the enrichment service in case of supply disruption, are investigated in this study. We investigated the 20 NPT countries which are non-nuclear-weapon states and possess operable commercial LWRs in October 2012 as potential participants for each proposal. As a result of literature researching, we have extracted factors that can be considered as important for a country to participate or not participate in the assurance of nuclear fuel supply. Then we have computed incentive and disincentive parameters for each country. The results show that the participation expectancy decreases in the order of IAEA Fuel Bank proposal, Russian LEU Reserve proposal, AFS proposal, WNA proposal and 6-Country proposal. The 'IAEA fuel bank proposal' would be triggered in case of the supply disruption which cannot be solved by the market mechanism and bilateral agreements.

  10. Practitioner Perspectives Matter: Public Policy and Private Investment in the U.S. Electric Power Sector

    E-Print Network [OSTI]

    Barradale, Merrill Jones

    2010-01-01T23:59:59.000Z

    on U.S. Wind Power Installation, Cost, and Performanceon U.S. Wind Power Installation, Cost, and Performancenot returned). Higher wind supply costs; Greater reliance on

  11. A Tariff for Reactive Power

    SciTech Connect (OSTI)

    Kueck, John D [ORNL; Kirby, Brendan J [ORNL; Li, Fangxing [ORNL; Tufon, Christopher [Pacific Gas and Electric Company; Isemonger, Alan [California Independent System Operator

    2008-07-01T23:59:59.000Z

    Two kinds of power are required to operate an electric power system: real power, measured in watts, and reactive power, measured in volt-amperes reactive or VARs. Reactive power supply is one of a class of power system reliability services collectively known as ancillary services, and is essential for the reliable operation of the bulk power system. Reactive power flows when current leads or lags behind voltage. Typically, the current in a distribution system lags behind voltage because of inductive loads such as motors. Reactive power flow wastes energy and capacity and causes voltage droop. To correct lagging power flow, leading reactive power (current leading voltage) is supplied to bring the current into phase with voltage. When the current is in phase with voltage, there is a reduction in system losses, an increase in system capacity, and a rise in voltage. Reactive power can be supplied from either static or dynamic VAR sources. Static sources are typically transmission and distribution equipment, such as capacitors at substations, and their cost has historically been included in the revenue requirement of the transmission operator (TO), and recovered through cost-of-service rates. By contrast, dynamic sources are typically generators capable of producing variable levels of reactive power by automatically controlling the generator to regulate voltage. Transmission system devices such as synchronous condensers can also provide dynamic reactive power. A class of solid state devices (called flexible AC transmission system devices or FACTs) can provide dynamic reactive power. One specific device has the unfortunate name of static VAR compensator (SVC), where 'static' refers to the solid state nature of the device (it does not include rotating equipment) and not to the production of static reactive power. Dynamic sources at the distribution level, while more costly would be very useful in helping to regulate local voltage. Local voltage regulation would reduce system losses, increase circuit capacity, increase reliability, and improve efficiency. Reactive power is theoretically available from any inverter-based equipment such as photovoltaic (PV) systems, fuel cells, microturbines, and adjustable-speed drives. However, the installation is usually only economical if reactive power supply is considered during the design and construction phase. In this report, we find that if the inverters of PV systems or the generators of combined heat and power (CHP) systems were designed with capability to supply dynamic reactive power, they could do this quite economically. In fact, on an annualized basis, these inverters and generators may be able to supply dynamic reactive power for about $5 or $6 per kVAR. The savings from the local supply of dynamic reactive power would be in reduced losses, increased capacity, and decreased transmission congestion. The net savings are estimated to be about $7 per kVAR on an annualized basis for a hypothetical circuit. Thus the distribution company could economically purchase a dynamic reactive power service from customers for perhaps $6/kVAR. This practice would provide for better voltage regulation in the distribution system and would provide an alternate revenue source to help amortize the cost of PV and CHP installations. As distribution and transmission systems are operated under rising levels of stress, the value of local dynamic reactive supply is expected to grow. Also, large power inverters, in the range of 500 kW to 1 MW, are expected to decrease in cost as they become mass produced. This report provides one data point which shows that the local supply of dynamic reactive power is marginally profitable at present for a hypothetical circuit. We expect that the trends of growing power flow on the existing system and mass production of inverters for distributed energy devices will make the dynamic supply of reactive power from customers an integral component of economical and reliable system operation in the future.

  12. Petroluem Supply Monthly, May 1993

    SciTech Connect (OSTI)

    Not Available

    1993-06-04T23:59:59.000Z

    Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  13. Petroleum Supply Monthly, November 1984

    SciTech Connect (OSTI)

    Not Available

    1985-01-28T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for November 1984. Information on crude oil, gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Summary statistics include data from 1973 to 1984. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude oil, net receipts, crude losses, refinery inputs, exports, products supplied,and ending stocks. The focus article, US Petroleum Developments - - 1984., summarizes changes in consumption, refinery operations, petroleum stocks, imports, production and prices. The article includes an update on refinery closings.

  14. Petroleum Supply Monthly, January 1985

    SciTech Connect (OSTI)

    Not Available

    1985-03-01T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for January, 1985. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. This month's issue features Trends in Petroleum Product Consumption. This article describes the changing patterns of US petroleum product consumption in recent years, for the major projects and by end-use sectors.

  15. Petroleum Supply Monthly, December 1984

    SciTech Connect (OSTI)

    Not Available

    1985-02-01T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for December 1984. Information on crude oil, gasoline, distillate fuel oil, residual fuel oil, and liquefied petroleum gases are included. Summary statistics include data from 1973 through January 1985. Detailed statistics show production for the current month as well as the year-to-date. Data are also tubulated for the US Petroleum Administration for Defense (PAD) District which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude oil, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. The featured article, US Petroleum Import/Export Trends, highlights 1984 activities and discusses historical US trade patterns for crude oil and petroleum products. 12 figures, 33 tables.

  16. Petroleum Supply Monthly, July 1990

    SciTech Connect (OSTI)

    Not Available

    1990-09-28T23:59:59.000Z

    Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  17. Power Factor Reactive Power

    E-Print Network [OSTI]

    motor power: 117.7 V x 5.1 A = 600 W? = 0.6 kW? NOT the power measured by meter #12;Page 9 PSERC: displacement power factor: angle between voltage and current = 0 degrees pf = cos(0 degrees) = 1.0 true powerPage 1 PSERC Power Factor and Reactive Power Ward Jewell Wichita State University Power Systems

  18. Electronics Division Technical Note No. 189 File: \\\\EAGLE\\cv-cdl-sis\\Docs\\Rack\\SIS Mixer Bias Supply\\Simulation\\Report2.doc Page 1 of 5

    E-Print Network [OSTI]

    Groppi, Christopher

    1 to protect the mixer junction from static discharge1 . The mixers are powered by bias suppliesElectronics Division Technical Note No. 189 File: \\\\EAGLE\\cv-cdl-sis\\Docs\\Rack\\SIS Mixer Bias Supply\\Simulation\\Report2.doc Page 1 of 5 Stability Analysis of SIS Mixer Bias Supply with 1K Ohm

  19. Failure is an option Andrew Rice Sherif Akoush Andy Hopper

    E-Print Network [OSTI]

    Cambridge, University of

    by infrastructure systems such as Uninterruptible Power Supplies (UPSs) and cooling systems. The energy consump's power and cool- ing infrastructure can have a big impact on reducing overall energy costs. One means- tion in the US due to servers and associated cooling systems alone has been estimated at 1.2% of total

  20. Ris-R-1257(EN) Isolated Systems with Wind Power

    E-Print Network [OSTI]

    energy in isolated communities. So far most studies of isolated systems with wind power have been case and economical feasibility of isolated power supply systems with wind energy. General guidelines and checklists project costs 24 5.5.2 Cost of Energy, COE 25 5.5.3 Value of Energy, VOE 25 Primary power supply 25

  1. Charlotte Green Supply Chain: Residential Retrofitting | Department...

    Broader source: Energy.gov (indexed) [DOE]

    Charlotte Green Supply Chain: Residential Retrofitting Charlotte Green Supply Chain: Residential Retrofitting July 30, 2010 - 10:50am Addthis Joshua DeLung What does this mean for...

  2. An integrative framework for architecting supply chains

    E-Print Network [OSTI]

    Cela Díaz, Fernando

    2006-01-01T23:59:59.000Z

    This thesis explores the limitations of classic models of supply chain management, and proposes a new view based on the concept of value-driven supply chains, and a method of analysis and design based on the concepts of ...

  3. Supply chain management in the cement industry

    E-Print Network [OSTI]

    Agudelo, Isabel

    2009-01-01T23:59:59.000Z

    Traditionally supply chain management has played an operational role within cement and mineral extraction commodity companies. Recently, cost reduction projects have brought supply chain management into the limelight. In ...

  4. Loss of coordination in competitive supply chains

    E-Print Network [OSTI]

    Teo, Koon Soon

    2009-01-01T23:59:59.000Z

    The loss of coordination in supply chains quantifies the inefficiency (i.e. the loss of total profit) due to the presence of competition in the supply chain. In this thesis, we discuss four models: one model with multiple ...

  5. Accelerating the transformation of power systems

    E-Print Network [OSTI]

    Accelerating the transformation of power systems Introduction Flexibility of operation--the ability of a power system to respond to change in demand and supply--is a characteristic of all power systems. Flexibility is especially prized in twenty-first century power systems, with higher levels of grid

  6. Low Power Silicon Devices Dieter K. Schroder

    E-Print Network [OSTI]

    Schroder, Dieter K.

    dissipation, and 3. con- servation of power in desktop systems where a com- petitive life cycle cost-to-performance ratio demands low power for reduced power supply and cooling costs.3 Lower power consumption leads electronics where cooling in the unit is more difficult and batteries have limited lifetime. DRAM cir- cuits

  7. Agents on the Web Supply Chains

    E-Print Network [OSTI]

    Almor, Amit

    Agents on the Web Automating Supply Chains 90 JULY · AUGUST 2001 http://computer.org/internet/ 1089

  8. Coupling Renewable Energy Supply with Deferrable Demand

    E-Print Network [OSTI]

    Papavasiliou, Anthony

    2011-01-01T23:59:59.000Z

    Scale Renewable Energy Integration . . . . . . . . . . .Impacts of Renewable Energy Supply . . . . . . . . . . . . .1.3 Coupling Renewable Energy with Deferrable

  9. Supply Chain and Information Sciences Technology 2010

    E-Print Network [OSTI]

    Guiltinan, Mark

    Supply Chain and Information Sciences Technology 2010 Supply Chain and Information Systems Technology Minor SCIST Minor Application Department of Supply Chain & Information Systems College of Information Sciences and Technology Overview The minor in SCIST is structured to provide students not majoring

  10. Supply-side utility economics

    SciTech Connect (OSTI)

    Platt, H.D.

    1985-06-27T23:59:59.000Z

    This article makes two main points: that electricity is a necessary resource, and that utilities respond to incentives as do individuals. From them, the author deduces that the US will have a power shortage within the foreseeable future unless utility regulators begin to consider future power plant needs realistically.

  11. Sandia Energy - Sandia-Electric Power Research Institute Partnership...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CTRLBRD Inverter Control Board; CRTLSW Inverter Control Software; CPS Inverter Control Power Supply; CYL hydraulic cylinder; DAS Data Acquisition System; ECON ...

  12. "Annual Electric Power Industry Report (EIA-861 data file)

    U.S. Energy Information Administration (EIA) Indexed Site

    data updated Table 7. Electric Power Industry Emissions Estimates, 1990- 2012 - Total emission rates added Table 10. Supply and Disposition of Electricity, 1990- 2012 - Data issues...

  13. Wind Vision Chapter 2: Wind Power in the United States

    Broader source: Energy.gov (indexed) [DOE]

    M; Holtinnen, H.; Sder, L.; Clark, C.; Pineda, I. "Markets to Facilitate Wind and Solar Energy Integration in the Bulk Power Supply: An IEA Task 25 Collaboration."...

  14. Programmable Power Supplies PS2520G PS2521G

    E-Print Network [OSTI]

    Woodall, Jerry M.

    ) This fact sheet is one in a series containing information to help you select foods that provide adequate and potassium · Alcoholic beverages · Food safety What is "a good food source"? A good food source of folate at 180 micrograms per day for women 19 to 50 years of age and 200 micrograms for men 19 to 50 years

  15. Handling Food and Supplies during Power Loss (Spanish) 

    E-Print Network [OSTI]

    Schoessow, Courtney

    2007-10-08T23:59:59.000Z

    : http://AgriLifebookstore.org Los programas educativos de Texas AgriLife Extension Service est?n disponibles para todas las personas, sin distinci?n de raza, color, sexo, discapacidad, religi?n, edad u origen nacional. Emitido para el desarrollo del...

  16. Handling Food and Supplies during Power Loss (Spanish)

    E-Print Network [OSTI]

    Schoessow, Courtney

    2007-10-08T23:59:59.000Z

    : http://AgriLifebookstore.org Los programas educativos de Texas AgriLife Extension Service est?n disponibles para todas las personas, sin distinci?n de raza, color, sexo, discapacidad, religi?n, edad u origen nacional. Emitido para el desarrollo del...

  17. Nationwide: New Efficiency Standards for Power Supplies Anticipate...

    Office of Environmental Management (EM)

    energy bills of U.S. families and businesses by nearly 4 billion, and reduce carbon emissions by nearly 47 million metric tons (equivalent to the emissions produced by the annual...

  18. Nuclear energy is an important source of power, supplying 20

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    energy expansion by developing options to increase the energy extracted from nuclear fuel, improve waste management, and strengthen nuclear nonproliferation controls. To...

  19. Multimegawatt space nuclear power supply: Phase 1, Final report

    SciTech Connect (OSTI)

    Not Available

    1989-02-17T23:59:59.000Z

    The Phase 2 program objectives are to (1) demonstrate concept feasibility, (2) develop a preliminary design, and (3) complete Phase 3 engineering development and ground test plans. The approach to accomplish these objectives is to prove technical feasibility of our baseline design early in the program while maintaining flexibility to easily respond to changing requirements and advances in technology. This approach recognizes that technology is advancing rapidly while the operational phase MSNPS is 15 to 20 years in the future. This plan further recognizes that the weapons platform and Advanced Launch System (ALS) are in very early program definition stages; consequently, their requirements, interfaces, and technological basis will evolve. This document outlines the Phase 2 plan along with task scheduling of the various program aspects.

  20. Developing a power supply solution for a mobile robot

    E-Print Network [OSTI]

    Zachmann, Gabriel

    (Technical Informatics and Computer Systems) Prof. Dr. Gabriel Zachmann (Computer Graphics) Prof. Dr

  1. Correction Magnet Power Supplies for APS Machine Y. O. Kang

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Ton: (Ton the conduction time of both switches S 1 and S4) Figure 2 (a) shows the equivalent circuit when switches S 1 and S4 are turned ON. Then, we can write a differential...

  2. CEA ? External Power Supplies, CCE Overview and Update presentation...

    Broader source: Energy.gov (indexed) [DOE]

    & Publications AHAM - CCE Overview and Update, dated 06072011 NEMA Distribution Transformers, CCE Overview and Update presentation, dated 05242011 NEMA Lighting, CCE Overview...

  3. New Energy Efficiency Standards for External Power Supplies to...

    Energy Savers [EERE]

    on President Obama's State of the Union address, which called for reducing carbon pollution and helping communities move to greater energy efficiency, the Energy Department...

  4. Opticle fibre calibration system and adaptive power supply

    E-Print Network [OSTI]

    Cvach, J; Kovalcuk, M; Kvasnicka, J; Polak, I; Smolik, J

    2015-01-01T23:59:59.000Z

    We summarize the recent activity of our group in the calibration, monitoring and gain stabilization of photodetectors, primarily silicon photomultipliers, in calorimeters using scintillator as active medium. The task originally solved for the CALICE analog hadron calorimeter founds application in other experiments.

  5. Opticle fibre calibration system and adaptive power supply

    E-Print Network [OSTI]

    J. Cvach; M. Janata; M. Kovalcuk; J. Kvasnicka; I. Polak; J. Smolik

    2015-03-24T23:59:59.000Z

    We summarize the recent activity of our group in the calibration, monitoring and gain stabilization of photodetectors, primarily silicon photomultipliers, in calorimeters using scintillator as active medium. The task originally solved for the CALICE analog hadron calorimeter founds application in other experiments.

  6. Nationwide: New Efficiency Standards for Power Supplies Anticipate Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed offOCHCO2:Introduction toManagement ofConverDyn NOPRNancyNational SupplementalServices »Savings |

  7. Nuclear energy is an important source of power, supplying 20

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Science (SC)Integrated CodesTransparencyDOE Project TapsDOERecoveryNuclearLife Cycle

  8. Dishergarh Power Supply Company Ltd | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual SiteofEvaluating A Potential Microhydro SiteDaytonDestilariaDirectDirect GlobalDisenco

  9. Meeting on Battery Chargers and External Power Supplies | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the.pdfBreaking ofOil & GasTechnical PublicationsDepartmentEnergyEnergy on

  10. New Energy Efficiency Standards for External Power Supplies to Cut

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy China 2015of 2005 attheMohammed Khan -DepartmentDepartment of EnergyFY 2014

  11. Meeting on Battery Chargers and External Power Supplies | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment3311, 3312), OctoberMay 18-19, 2004 MeetingDepartment 1)Energy

  12. Reliant Energy Power Supply LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghuraji Agro Industries Pvt Ltd Jump to: navigation, searchRayreviewAl., 2005)Coastal Plains

  13. New Energy Efficiency Standards for External Power Supplies to Cut

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the.pdfBreaking ofOilNEW HAMPSHIREof Energy Investigates PortFreezers to Save on

  14. Petroleum supply monthly: December 1993

    SciTech Connect (OSTI)

    Not Available

    1993-12-01T23:59:59.000Z

    Data are presented which describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States. Data are presented in two sections: Summary Statistics, presenting a time series of selected petroleum data on a U.S. level, and Detailed Statistics, presenting statistics for the most current month available as well as year to date.

  15. Supply Stores | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed off Energy.gov. Are you sure you wantJoin us for|Idaho |Energy Supercomputers: ExtremeSupply

  16. A Thermally-Aware Methodology for Design-Specific Optimization of Supply and Threshold Voltages in Nanometer Scale ICs

    E-Print Network [OSTI]

    411 A Thermally-Aware Methodology for Design-Specific Optimization of Supply and Threshold Voltages and associated thermal effects have strong impact on the packaging, cooling costs, and reliability for deep submicron technologies [2-5]. For power-constrained applications, lowering supply voltage (Vdd) offers

  17. Power Network-on-Chip for Scalable Power Delivery Inna Vaisband and Eby G. Friedman

    E-Print Network [OSTI]

    Friedman, Eby G.

    Power Network-on-Chip for Scalable Power Delivery Inna Vaisband and Eby G. Friedman Department}@ece.rochester.edu Abstract--Delivering high quality power to the on-chip cir- cuitry with minimum energy loss is an essential component of integrated circuits. The quality of the power supply can be efficiently addressed with multiple

  18. Power Attack Resistant Cryptosystem Design: A Dynamic Voltage and Frequency Switching Approach

    E-Print Network [OSTI]

    Boyer, Edmond

    studied by several groups. Power attacks, which infer program behavior from observing power supply current (DPA), which identifies cryptographic keys by monitoring processor power supply current, is a very real analysis [7], power analysis [1], electromagnetic analysis [8] and fault induction [9]. Here, we are most

  19. Roadmap for Agriculture Biomass Feedstock Supply in the United States

    SciTech Connect (OSTI)

    J. Richard Hess; Thomas D. Foust; Reed Hoskinson; David Thompson

    2003-11-01T23:59:59.000Z

    The Biomass Research and Development Technical Advisory Committee established a goal that biomass will supply 5% of the nation’s power, 20% of its transportation fuels, and 25% of its chemicals by 2030. These combined goals are approximately equivalent to 30% of the country’s current petroleum consumption. The benefits of a robust biorefinery industry supplying this amount of domestically produced power, fuels, and products are considerable, including decreased demand for imported oil, revenue to the depressed agricultural industry, and revitalized rural economies. A consistent supply of highquality, low-cost feedstock is vital to achieving this goal. This biomass roadmap defines the research and development (R&D) path to supplying the feedstock needs of the biorefinery and to achieving the important national goals set for biomass. To meet these goals, the biorefinery industry must be more sustainable than the systems it will replace. Sustainability hinges on the economic profitability of all participants, on environmental impact of every step in the process, and on social impact of the product and its production. In early 2003, a series of colloquies were held to define and prioritize the R&D needs for supplying feedstock to the biorefinery in a sustainable manner. These colloquies involved participants and stakeholders in the feedstock supply chain, including growers, transporters, equipment manufacturers, and processors as well as environmental groups and others with a vested interest in ensuring the sustainability of the biorefinery. From this series of colloquies, four high-level strategic goals were set for the feedstock area: • Biomass Availability – By 2030, 1 billion dry tons of lignocellulosic feedstock is needed annually to achieve the power, fuel, and chemical production goals set by the Biomass Research and Development Technology Advisory Production Committee • Sustainability – Production and use of the 1 billion dry tons annually must be accomplished in a sustainable manner • Feedstock Infrastructure – An integrated feedstock supply system must be developed and implemented that can serve the feedstock needs of the biorefinery at the cost, quality, and consistency of the set targets • System Profitability – Economic profitability and sustainability need to be ensured for all required participants in the feedstock supply system. For each step in the biomass supply process—production, harvesting and collection, storage, preprocessing, system integration, and transportation—this roadmap addresses the current technical situations, performance targets, technical barriers, R&D needs, and R&D priorities to overcome technical barriers and achieve performance targets. Crop residue biomass is an attractive starting feedstock, which shows the best near-term promise as a biorefinery feedstock. Because crop residue is a by-product of grain production, it is an abundant, underutilized, and low cost biomass resource. Corn stover and cereal straw are the two most abundant crop residues available in the United States. Therefore, this roadmap focuses primarily on the R&D needed for using these biomass sources as viable biorefinery feedstocks. However, achieving the goal of 1 billion dry tons of lignocellulosic feedstock will require the use of other biomass sources such as dedicated energy crops. In the long term, the R&D needs identified in this roadmap will need to accommodate these other sources of biomass as well.

  20. Petroleum supply annual 1995: Volume 1

    SciTech Connect (OSTI)

    NONE

    1996-05-01T23:59:59.000Z

    The {ital Petroleum Supply Annual} contains information on supply and disposition of crude oil and petroleum products. It reflects data collected from the petroleum industry during 1995 through monthly surveys, and it is divided into 2 volumes. This volume contains three sections: summary statistics, detailed statistics, and selected refinery statistics, each with final annual data. (The other volume contains final statistics for each month and replaces data previously published in the {ital Petroleum Supply Monthly}).

  1. GI Self-Supply Pilot Overview

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    BPA TRANSMISSION SERVICES Transmission Wind Integration Systems Team GENERATION IMBALANCE SELF SUPPLY PILOT PROJECT OVERVIEW VERSION: 0.1 UPDATED: 7292009 giself-supplypilotov...

  2. Assessing reliability in energy supply systems

    E-Print Network [OSTI]

    McCarthy, Ryan W.; Ogden, Joan M.; Sperling, Daniel

    2007-01-01T23:59:59.000Z

    pathway supplying hydrogen via pipeline from a centralizedgas with pipeline distribution of hydrogen, and 2) on-sitehydrogen is transported to the refueling stations via pipeline

  3. Assessing Reliability in Energy Supply Systems

    E-Print Network [OSTI]

    McCarthy, Ryan; Ogden, Joan M.; Sperling, Dan

    2008-01-01T23:59:59.000Z

    pathway supplying hydrogen via pipeline from a centralizedgas with pipeline distribution of hydrogen, and 2) on-sitehydrogen is transported to the refueling stations via pipeline

  4. Assessing reliability in energy supply systems

    E-Print Network [OSTI]

    McCarthy, Ryan W.; Ogden, Joan M.; Sperling, Daniel

    2007-01-01T23:59:59.000Z

    liquefied natural gas (LNG) trading expected to increase insteam reformation production facility using imported LNG.The LNG supplies come primarily from Trinidad and Tobago,

  5. Assessing Reliability in Energy Supply Systems

    E-Print Network [OSTI]

    McCarthy, Ryan; Ogden, Joan M.; Sperling, Dan

    2008-01-01T23:59:59.000Z

    liquefied natural gas (LNG) trading expected to increase insteam reformation production facility using imported LNG.The LNG supplies come primarily from Trinidad and Tobago,

  6. AC system stability analysis and assessment for Shipboard Power Systems 

    E-Print Network [OSTI]

    Qi, Li

    2006-04-12T23:59:59.000Z

    The electric power systems in U.S. Navy ships supply energy to sophisticated systems for weapons, communications, navigation and operation. The reliability and survivability of a Shipboard Power System (SPS) are critical ...

  7. Power Conditioning and Control Applications for Energy Conservation

    E-Print Network [OSTI]

    Brushwood, J. S.

    1982-01-01T23:59:59.000Z

    Electrical power conditioning and control (PCC) systems are finding cost effective applications in AC motor drives, lamp ballasts and power supplies. Substantial system efficiency improvements are being realized when the appropriate PCC system...

  8. DOE Notice of Proposed Rulemaking to Amend the External Power...

    Office of Environmental Management (EM)

    Proposed Rulemaking to Amend the External Power Supply Test Procedure; Docket No. EERE-2014-BT-TP-0043 RIN 1904-AD36 DOE Notice of Proposed Rulemaking to Amend the External Power...

  9. AC system stability analysis and assessment for Shipboard Power Systems

    E-Print Network [OSTI]

    Qi, Li

    2006-04-12T23:59:59.000Z

    The electric power systems in U.S. Navy ships supply energy to sophisticated systems for weapons, communications, navigation and operation. The reliability and survivability of a Shipboard Power System (SPS) are critical to the mission of a Navy...

  10. Power throttling of collections of computing elements

    DOE Patents [OSTI]

    Bellofatto, Ralph E. (Ridgefield, CT); Coteus, Paul W. (Yorktown Heights, NY); Crumley, Paul G. (Yorktown Heights, NY); Gara, Alan G. (Mount Kidsco, NY); Giampapa, Mark E. (Irvington, NY); Gooding; Thomas M. (Rochester, MN); Haring, Rudolf A. (Cortlandt Manor, NY); Megerian, Mark G. (Rochester, MN); Ohmacht, Martin (Yorktown Heights, NY); Reed, Don D. (Mantorville, MN); Swetz, Richard A. (Mahopac, NY); Takken, Todd (Brewster, NY)

    2011-08-16T23:59:59.000Z

    An apparatus and method for controlling power usage in a computer includes a plurality of computers communicating with a local control device, and a power source supplying power to the local control device and the computer. A plurality of sensors communicate with the computer for ascertaining power usage of the computer, and a system control device communicates with the computer for controlling power usage of the computer.

  11. Certified Professional in Supply Management (CPSM) Review Series: Exam 2: Effective Supply Management Performance

    E-Print Network [OSTI]

    · Materials and Inventory Management · Organization/Department Assessment · Planning · Product and ServiceCertified Professional in Supply Management (CPSM) Review Series: Exam 2: Effective Supply Management Performance Dates: October 28, 2011 Location: Rutgers University­ Livingston Campus, Tillett Hall

  12. Local Safety Committee Engineering

    E-Print Network [OSTI]

    Saskatchewan, University of

    Minutes Local Safety Committee Name of Committee Engineering Worksite Mailing Address & Postal Code. Ventilation fume hoods V. Bendig and FMD report that an uninterrupted power supply will be attached to the ventilation control panel the week of Dec. 9. Action: T. Zintel and L. Harder will conduct a test the first

  13. Fuel cells as a backup energy source for high availability network servers

    E-Print Network [OSTI]

    Humphrey, Daniel Alan

    2008-10-10T23:59:59.000Z

    This thesis proposes an uninterruptible power supply, UPS for high availability servers with fuel cells as its back up energy source. The system comprises a DC to DC converter designed to accommodate the fuel cellâ s wide output voltage range. A...

  14. This document is a preprint of the paper: L. Meng, T. Dragicevic, J.M. Guerrero, and J.C Vasquez, "Optimization with system damping restoration for droop controlled dc-dc converters," in

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    , "Optimization with system damping restoration for droop controlled dc-dc converters," in Proc. IEEE Energy Restoration for Droop Controlled DC-DC Converters Lexuan Meng, Tomislav Dragicevic, Josep M. Guerrero, Juan C systems and uninterruptable power supply systems. Droop control along with virtual resistance (VR

  15. Fuzzy Logic-Based State-of-Health Determination of Lead Acid Batteries Pritpal Singh

    E-Print Network [OSTI]

    Singh, Pritpal

    Fuzzy Logic-Based State-of-Health Determination of Lead Acid Batteries Pritpal Singh Villanova) of uninterruptible power supply (UPS) batteries using impedance measurements has been demonstrated by several extracted equivalent circuit parameters to correlate with battery SOH. This is a computationally extensive

  16. Fuel cells as a backup energy source for high availability network servers 

    E-Print Network [OSTI]

    Humphrey, Daniel Alan

    2008-10-10T23:59:59.000Z

    This thesis proposes an uninterruptible power supply, UPS for high availability servers with fuel cells as its back up energy source. The system comprises a DC to DC converter designed to accommodate the fuel cellâ s wide output voltage range. A...

  17. Power Plant Power Plant

    E-Print Network [OSTI]

    Tingley, Joseph V.

    Basin Center for Geothermal Energy at University of Nevada, Reno (UNR) 2 Nevada Geodetic LaboratoryStillwater Power Plant Wabuska Power Plant Casa Diablo Power Plant Glass Mountain Geothermal Area Lassen Geothermal Area Coso Hot Springs Power Plants Lake City Geothermal Area Thermo Geothermal Area

  18. Supply Chain and Blade Manufacturing Considerations in the Global Wind Industry (Presentation)

    SciTech Connect (OSTI)

    James, T.; Goodrich, A.

    2013-12-01T23:59:59.000Z

    This briefing provides an overview of supply chain developments in the global wind industry and a detailed assessment of blade manufacturing considerations for U.S. end-markets. The report discusses the international trade flows of wind power equipment, blade manufacturing and logistical costs, and qualitative issues that often influence factory location decisions. To help guide policy and research and development strategy decisions, this report offers a comprehensive perspective of both quantitative and qualitative factors that affect selected supply chain developments in the growing wind power industry.

  19. Protective supplied breathing air garment

    DOE Patents [OSTI]

    Childers, E.L.; Hortenau, E.F. von.

    1984-07-10T23:59:59.000Z

    A breathing air garment is disclosed for isolating a wearer from hostile environments containing toxins or irritants includes a suit and a separate head protective enclosure or hood engaging a suit collar in sealing attachment. The hood and suit collar are cylindrically shaped and dimensioned to enable the wearer to withdraw his hands from the suit sleeves to perform manual tasks within the hood interior. Breathing air is supplied from an external air line with an air delivery hose attached to the hood interior. The hose feeds air into an annular halo-like fiber-filled plenum having spaced discharge orifices attached to the hood top wall. A plurality of air exhaust/check valves located at the suit extremities cooperate with the hood air delivery system to provide a cooling flow of circulating air from the hood throughout the suit interior. A suit entry seal provided on the suit rear torso panel permits access into the suit and is sealed with an adhesive sealing flap. 17 figs.

  20. Lead -- supply/demand outlook

    SciTech Connect (OSTI)

    Schnull, T. [Noranda, Inc., Toronto, Ontario (Canada)

    1999-03-01T23:59:59.000Z

    As Japan goes--so goes the world. That was the title of a recent lead article in The Economist that soberly discussed the potential of much more severe global economic problems occurring, if rapid and coordinated efforts were not made to stabilize the economic situation in Asia in general, and in Japan in particular. During the first 6 months of last year, commodity markets reacted violently to the spreading economic problems in Asia. More recent currency and financial problems in Russia have exacerbated an already unpleasant situation. One commodity after another--including oil, many of the agricultural commodities, and each of the base metals--have dropped sharply in price. Many are now trading at multiyear lows. Until there is an overall improvement in the outlook for these regions, sentiment will likely continue to be negative, and metals prices will remain under pressure. That being said, lead has maintained its value better than many other commodities during these difficult times, finding support in relatively strong fundamentals. The author takes a closer look at those supply and demand fundamentals, beginning with consumption.

  1. Multi-Project Baselines for Evaluation of Industrial Energy-Efficiency and Electric Power Projects

    E-Print Network [OSTI]

    2001-01-01T23:59:59.000Z

    and wind to meet the off grid supply. The future expansionagency for decentralized off-grid supply of power of 6 MW ofProject 5 is based on Off-grid Solar Home Systems. The aim

  2. Biomass Supply and Carbon Accounting for

    E-Print Network [OSTI]

    Biomass Supply and Carbon Accounting for Southeastern Forests February 2012 #12;This Biomass Supply and Carbon Accounting for Southeastern Forests study was conducted by the Biomass Energy Resource Center Biomass Energy Resource Center Kamalesh Doshi Biomass Energy Resource Center Hillary Emick Biomass Energy

  3. EXOTIC OPTIONS FOR INTERRUPTIBLE ELECTRICITY SUPPLY CONTRACTS

    E-Print Network [OSTI]

    with different strike prices. Such options allow hedging and valuation of supply curtailment risk, while demand side participation in the mitigation of supply shortages for energy and reserves. Newly curtailment can provide an efficient substitute for generation capacity in providing balancing energy

  4. Proposal for the Cryogenic Supply of a

    E-Print Network [OSTI]

    1 Proposal for the Cryogenic Supply of a Single TTF / FEL - Cryomodule Test Bench TESLA Report No supply are described. 1. Introduction For the time being, TTF- cryomodules can only be cold tested after will change. The quadrupoles will be cooled in the 2.0 K liquid bath instead by the 4.5K cooling circuit

  5. Transportation Energy: Supply, Demand and the Future

    E-Print Network [OSTI]

    Saldin, Dilano

    Transportation Energy: Supply, Demand and the Future http://www.uwm.edu/Dept/CUTS//2050/energy05 as a source of energy. Global supply and demand trends will have a profound impact on the ability to use our) Transportation energy demand in the U.S. has increased because of the greater use of less fuel efficient vehicles

  6. Optimal Trading Strategy Supply/Demand Dynamics

    E-Print Network [OSTI]

    Gabrieli, John

    prices through the changes in their supply/demand.2 Thus, to study how market participants trade can have interesting implications on the observed behavior of intraday volume, volatility and prices: November 15, 2004. This Draft: April 8, 2006 Abstract The supply/demand of a security in the market

  7. Supply Chain Management Faculty Brian Fugate

    E-Print Network [OSTI]

    University. He has worked in materials management professionally for over 10 years with high tech electronicsSupply Chain Management Faculty Brian Fugate Brian S. Fugate (Ph.D University of Tennessee) is an Associate Professor of Supply Chain Management at Colorado State University. Brian worked in logistics

  8. Supply Chain Networks, Electronic Commerce, and Supply Side and Demand Side Risk

    E-Print Network [OSTI]

    Nagurney, Anna

    Supply Chain Networks, Electronic Commerce, and Supply Side and Demand Side Risk Anna Nagurney as well as demand side risk are included in the formulation. The model consists of three tiers of decision chain network equilibrium model with electronic com- merce and with supply side and demand side risk

  9. Certified Professional in Supply Management (CPSM) & Certified in Supply Management (CSM) Exam Preparation Series

    E-Print Network [OSTI]

    Lin, Xiaodong

    -Taking Hints and Tips Exam 2 Content Forecasting Logistics Materials and Inventory Management OrganizationCertified Professional in Supply Management (CPSM) & Certified in Supply Management (CSM) Exam for member companies of the Rutgers Center for Supply Chain Management. $425 for non-members This one day

  10. Coal slurry fuel supply and purge system

    DOE Patents [OSTI]

    McDowell, Robert E. (Fairview, PA); Basic, Steven L. (Hornell, NY); Smith, Russel M. (North East, PA)

    1994-01-01T23:59:59.000Z

    A coal slurry fuel supply and purge system for a locomotive engines is disclosed which includes a slurry recirculation path, a stand-by path for circulating slurry during idle or states of the engine when slurry fuel in not required by the engine, and an engine header fluid path connected to the stand-by path, for supplying and purging slurry fuel to and from fuel injectors. A controller controls the actuation of valves to facilitate supply and purge of slurry to and from the fuel injectors. A method for supplying and purging coal slurry in a compression ignition engine is disclosed which includes controlling fluid flow devices and valves in a plurality of fluid paths to facilitate continuous slurry recirculation and supply and purge of or slurry based on the operating state of the engine.

  11. Renewable Energy Powered Membrane Technology. 1. Development and Characterization of a Photovoltaic Hybrid Membrane System 

    E-Print Network [OSTI]

    Schäfer, Andrea; Broeckmann, Andreas; Richards, Bryce

    2007-01-01T23:59:59.000Z

    the unavailability of power in many such situations, renewable energy is an obvious solution to power such systems. However, renewable energy is an intermittent power supply and with regards to the performance of intermittently operated desalination systems, only...

  12. A Better Steam Engine: Designing a Distributed Concentrating Solar Combined Heat and Power System

    E-Print Network [OSTI]

    Norwood, Zachary Mills

    2011-01-01T23:59:59.000Z

    solar CHP system supplying arbitrary heat and power outputs.e Electrical power output of system Q Solar CHP to PV yearlysolar Rankine CHP system, sized equally in terms of peak power output,

  13. HIGH STABILITY CURRENT SUPPLY FOR ELECTRON MICROSCOPY

    E-Print Network [OSTI]

    Motamedi, Maryam Melani

    2012-01-01T23:59:59.000Z

    the current regulator. The power losses through the powerFETs are (31): Power Loss = I drain V ds The drain current (by design to lower the power loss is the drain to source

  14. Emergency Food and Water Supplies

    E-Print Network [OSTI]

    Van Laanen, Peggy

    1999-05-14T23:59:59.000Z

    1 day. An appliance thermometer can help monitor the inside freezer tem per a- ture. Use of dry ice. Dry ice can be used to help maintain adequate freezer temperature if the power is out for more than one day. Use these precautions when using... dry ice. Use 3 pounds dry ice per cubic foot of freezer space. Avoid direct contact of dry ice with skin. Dry ice will burn skin and is not for consumption. Wrap dry ice in brown paper for longer storage and separate it from food with a piece...

  15. Sandia Energy - Manufacturing Supply Chain

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Scienceand RequirementsCoatingsUltra-High-VoltagePowerUpdates Techno-EconomicLaunchManufacturing

  16. CALCULATING THE CARBON FOOTPRINT SUPPLY CHAIN FOR THE

    E-Print Network [OSTI]

    Su, Xiao

    CALCULATING THE CARBON FOOTPRINT SUPPLY CHAIN FOR THE SEMICONDUCTOR INDUSTRY A LEARNING TOOL By a complete supply chain #12;Carbon Footprint Supply Chain Carbon Trust defines carbon footprint of a supply chain as follows: "The carbon footprint of a product is the carbon dioxide emitted across the supply

  17. Petroleum supply annual 1993. Volume 1

    SciTech Connect (OSTI)

    Not Available

    1994-06-01T23:59:59.000Z

    The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1993 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains four sections: Summary Statistics, Detailed Statistics, Refinery Capacity, and Oxygenate Capacity each with final annual data. The second volume contains final statistics for each month of 1993, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Below is a description of each section in Volume 1 of the PSA.

  18. Petroleum supply annual 1994. Volume 1

    SciTech Connect (OSTI)

    NONE

    1995-05-22T23:59:59.000Z

    The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1994 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains four sections: Summary Statistics, Detailed Statistics, Refinery Capacity, and Oxygenate Capacity each with final annual data. The second volume contains final statistics for each month of 1994, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Below is a description of each section in Volume 1 of the PSA.

  19. Petroleum supply annual, 1997. Volume 1

    SciTech Connect (OSTI)

    NONE

    1998-06-01T23:59:59.000Z

    The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1997 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Statistics; each with final annual data. The second volume contains final statistics for each month of 1997, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. 16 figs., 48 tabs.

  20. Power marketing and renewable energy

    SciTech Connect (OSTI)

    Fang, J.M.

    1997-09-01T23:59:59.000Z

    Power marketing refers to wholesale and retail transactions of electric power made by companies other than public power entities and the regulated utilities that own the generation and distribution lines. The growth in power marketing has been a major development in the electric power industry during the last few years, and power marketers are expected to realize even more market opportunities as electric industry deregulation proceeds from wholesale competition to retail competition. This Topical Issues Brief examines the nature of the power marketing business and its relationship with renewable power. The information presented is based on interviews conducted with nine power marketing companies, which accounted for almost 54% of total power sales by power marketers in 1995. These interviews provided information on various viewpoints of power marketers, their experience with renewables, and their respective outlooks for including renewables in their resource portfolios. Some basic differences exist between wholesale and retail competition that should be recognized when discussing power marketing and renewable power. At the wholesale level, the majority of power marketers stress the commodity nature of electricity. The primary criteria for developing resource portfolios are the same as those of their wholesale customers: the cost and reliability of power supplies. At the retail level, electricity may be viewed as a product that includes value-added characteristics or services determined by customer preferences.

  1. Using auxiliary gas power for CCS energy needs in retrofitted coal power plants

    E-Print Network [OSTI]

    Bashadi, Sarah O.

    Adding post-combustion capture technology to existing coal-fired power plants is being considered as a near-term option for mitigating CO[subscript 2] emissions. To supply the thermal energy needed for CO[subscript 2] ...

  2. Improving Process Control Immunity to Supply Voltage Sags in Petroleum and Chemical Industries

    E-Print Network [OSTI]

    Mansoor, A.; Dorr, D.; Olson, G.

    IMPROVING PROCESS CONTROL IMMUNITY TO SUPPLY VOLTAGE SAGS IN PETROLEUM AND CHEMICAL INDUSTRIES Douglas Dorr and Arshad Mansoor EPRI Power Electronics Applications Center Knoxville, TN ABSTRACT In the modem industrial facility, many... by EPRI's Power Quality Test Facility clearly shows that CVT's are an excellent solution for voltage sag problems when they are sized properly. The optimum sizing is achieved when the CVT is loaded to no more than about 40 Figure 3. Batteryless UPS...

  3. Segmentation strategies for managing retail supply chains

    E-Print Network [OSTI]

    Liang, Catherine G. (Catherine Gloria)

    2011-01-01T23:59:59.000Z

    High-technology manufacturing companies often face rapid price decline and capacity constraints. Especially in the retail side of the business where the supply chain is much longer and revenue is sometimes not recognized ...

  4. Advanced Supply System Validation Workshop Agenda

    Broader source: Energy.gov [DOE]

    List of Assumptions and Draft Workshop Agenda for the Advanced Supply System Validation Workshop, February 3-4, 2014, Golden, Colorado, from the U.S. Department of Energy's Bioenergy Technologies Office.

  5. Supply chain practices in the petroleum downstream

    E-Print Network [OSTI]

    Santos Manzano, Fidel

    2005-01-01T23:59:59.000Z

    This thesis studies current supply chain practices in the petroleum downstream industry, using ExxonMobil as a case study. Based on the analysis of the literature and the interaction with industry experts, this work describes ...

  6. Essays on Married Women Labor Supply

    E-Print Network [OSTI]

    Li, Xinrong

    2012-02-14T23:59:59.000Z

    One of the very interesting demographic features in the US over the last three decades of the 20th century is the increase of the married women labor force participation rate. Over the same period, estimated labor supply elasticity varies...

  7. An analysis of oil supply disruption scenarios

    E-Print Network [OSTI]

    Mork, Knut Anton

    1981-01-01T23:59:59.000Z

    This report brings the results of simulations of some oil supply disruptions on the M.I.T. Energy Laboratory Energy Macro Model. This model has previously been used to study the macroeconomic effects of the 1973-74 and ...

  8. Polynomial policies in supply chain networks

    E-Print Network [OSTI]

    He, Liwei

    2010-01-01T23:59:59.000Z

    This thesis aims to solve the periodic-reviewed inventory control problem in supply chain networks with uncertain demand so as to minimize the overall cost of the system over a fixed planning time horizon. In such problems, ...

  9. Returning Home After a Disaster: Supply List

    E-Print Network [OSTI]

    Norman, Lisa

    2005-09-30T23:59:59.000Z

    When you return home after a disaster, you will want to have sturdy shoes, proper tools, clothes and medications for several days, and a first-aid kit. This publication also includes a list of necessary cleaning supplies....

  10. Supplies Needed Polyester Fleece (13" x 23")

    E-Print Network [OSTI]

    Supplies Needed Polyester Fleece (13" x 23") Polyester Thread This one is easy. Really easy inclined, add a drawstring to the top and it will double as a hat. Pretty cool, eh? Texas 4-H Clothing

  11. Supply chain and the executive agenda

    E-Print Network [OSTI]

    Peruvankal, James Paul

    2011-01-01T23:59:59.000Z

    In recent years, supply chain pundits and consultants emphasized the importance of strategies such as just-in-time, lean manufacturing, off- shoring or frequent deliveries to retail outlets. However, with significant ...

  12. Global Energy: Supply, Demand, Consequences, Opportunities

    ScienceCinema (OSTI)

    Arun Majumdar

    2010-01-08T23:59:59.000Z

    July 29, 2008 Berkeley Lab lecture: Arun Majumdar, Director of the Environmental Energy Technologies Division, discusses current and future projections of economic growth, population, and global energy demand and supply, and explores the implications of these trends for the environment.

  13. Risk in the Global Supply Chain

    E-Print Network [OSTI]

    Datta, Shoumen

    2006-01-01T23:59:59.000Z

    Carbon footprints are not on the priority list of risk analysts in operations management for at least half or more of global businesses. What are the other risks in the global supply chain?

  14. Northeast Gasoline Supply Reserve | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    supplements the Northeast Home Heating Oil Reserve, a one million barrel supply of ultra-low sulfur diesel, which was used for the first time by first-responders and to fill...

  15. Competitive developments in the electric supply industry

    SciTech Connect (OSTI)

    Bruder, G.F.; Lively, M.

    1996-12-31T23:59:59.000Z

    Competition in the electric supply industry is outlined. The following topics are discussed: six impending major developments in the electric industry; recent and projected developments in the industry; where is the industry headed?; and what the future holds.

  16. Response to changes in demand/supply

    E-Print Network [OSTI]

    Response to changes in demand/supply through improved marketing 21.2 #12;#12;111 Impacts of changes operating by some Korean paper companies for acquiring needed pulpwood as a first step for the construction

  17. The supply chain response to environmental pressures

    E-Print Network [OSTI]

    Paquette, Julie Rebecca

    2006-01-01T23:59:59.000Z

    Understanding and shaping the relationship between supply chain management and the natural environment is critical not only to human health and the environment, but to the future success of business. While the cumulative ...

  18. RECYCLING: SUPPLY, ECONOMICS, ENVIRONMENT, AND TECHNOLOGY

    E-Print Network [OSTI]

    Abubakr, Said

    RECYCLING: SUPPLY, ECONOMICS, ENVIRONMENT, AND TECHNOLOGY Panel Discussion Roundtable Moderator: S, although higher market values for recyclable will certainly stimulate increased interest in collection in recycling and deinking technologies and process design among North American, European, and Pacific Rim

  19. Application of Flow Battery in Marine Current Turbine System for Daily Power Management

    E-Print Network [OSTI]

    Brest, Université de

    ) generation system highly attractive as an electricity supply source for coastal areas and remote islands large mismatch between MCT produced power and grid-side (or load-side) demanded power. This paper as a backup power supply source in case of low battery state of charge (SoC) caused by losses during long

  20. Pricing and Hedging Electricity Supply Contracts: a Case with Tolling Agreements

    E-Print Network [OSTI]

    Pricing and Hedging Electricity Supply Contracts: a Case with Tolling Agreements Shi-Jie Deng Email Customized electric power contracts catering to specific business and risk management needs have gained increasing popularity among large energy firms in the restructured electricity in- dustry. A tolling