National Library of Energy BETA

Sample records for unac pad counted

  1. Multiplicity Counting

    SciTech Connect (OSTI)

    Geist, William H.

    2015-12-01

    This set of slides begins by giving background and a review of neutron counting; three attributes of a verification item are discussed: 240Pueff mass; α, the ratio of (α,n) neutrons to spontaneous fission neutrons; and leakage multiplication. It then takes up neutron detector systems – theory & concepts (coincidence counting, moderation, die-away time); detector systems – some important details (deadtime, corrections); introduction to multiplicity counting; multiplicity electronics and example distributions; singles, doubles, and triples from measured multiplicity distributions; and the point model: multiplicity mathematics.

  2. Job Counting Guidelines

    Office of Environmental Management (EM)

    Definitions and Guidelines for Counting Monthly and Quarterly EM Recovery Act Full Time Equivalents (FTEs) and Cumulative Head-Count The following updated definitions and...

  3. Prices by Sales Type, PAD District, and Selected States

    U.S. Energy Information Administration (EIA) Indexed Site

    Type, PAD District, and Selected States 224 Energy Information Administration Petroleum Marketing Annual 1997 Table 39. No. 2 Distillate a Prices by Sales Type, PAD District, and...

  4. Prices by Sales Type, PAD District, and Selected States

    U.S. Energy Information Administration (EIA) Indexed Site

    Type, PAD District, and Selected States 224 Energy Information Administration Petroleum Marketing Annual 1996 Table 39. No. 2 Distillate a Prices by Sales Type, PAD District, and...

  5. Special Analysis: Naval Reactor Waste Disposal Pad

    SciTech Connect (OSTI)

    Cook, J.R.

    2003-03-31

    This report presents the results of a special study of the Naval Reactor Waste Disposal Pad located within the boundary of the E-Area Low-Level Waste Facility at the Savannah River Site.

  6. Thermal Neutron Detectors with Discrete Anode Pad Readout

    SciTech Connect (OSTI)

    Yu,B.; Schaknowski, N.A., Smith, G.C., DeGeronimo, G., Vernon, E.O.

    2008-10-19

    A new two-dimensional thermal neutron detector concept that is capable of very high rates is being developed. It is based on neutron conversion in {sup 3}He in an ionization chamber (unity gas gain) that uses only a cathode and anode plane; there is no additional electrode such as a Frisch grid. The cathode is simply the entrance window, and the anode plane is composed of discrete pads, each with their own readout electronics implemented via application specific integrated circuits. The aim is to provide a new generation of detectors with key characteristics that are superior to existing techniques, such as higher count rate capability, better stability, lower sensitivity to background radiation, and more flexible geometries. Such capabilities will improve the performance of neutron scattering instruments at major neutron user facilities. In this paper, we report on progress with the development of a prototype device that has 48 x 48 anode pads and a sensitive area of 24cm x 24cm.

  7. FC-PAD Organization and Activities | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    FC-PAD Organization and Activities FC-PAD Organization and Activities This document provides an in-depth description of the organization of the Fuel Cell Consortium for Performance and Durability (FC-PAD), including its scientific activities and six different thrust areas. FC-PAD Organization and Activities (4.08 MB) More Documents & Publications FCTO Consortia Overview (HyMARC and FC-PAD) Webinar FCTO Consortia Overview (HyMARC and FC-PAD) Webinar DOE Fuel Cell Pre-Solicitation Workshop -

  8. Verde iPad app | Open Energy Information

    Open Energy Info (EERE)

    iPad app An energy audit tool for the iPad the recommends the best places to upgrade to energy star products, as well as how much money and carbon you will save by doing so....

  9. Calibration Pad Assignments for Spectral Gamma (November 1985) | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Pad Assignments for Spectral Gamma (November 1985) Calibration Pad Assignments for Spectral Gamma (November 1985) Calibration Pad Assignments for Spectral Gamma (November 1985) Calibration Pad Assignments for Spectral Gamma (November 1985) (5.3 MB) More Documents & Publications Parameter Assignments for Spectral Gamma-Ray Borehole Calibration Models (April 1984) Field Calibration Facilities for Environmental Measurement of Radium, Thorium, and Potassium (October 2013) Grade

  10. Fast counting electronics for neutron coincidence counting

    DOE Patents [OSTI]

    Swansen, J.E.

    1985-03-05

    An amplifier-discriminator is tailored to output a very short pulse upon an above-threshold input from a detector which may be a /sup 3/He detector. The short pulse output is stretched and energizes a light emitting diode (LED) to provide a visual output of operation and pulse detection. The short pulse is further fed to a digital section for processing and possible ORing with other like generated pulses. Finally, the output (or ORed output) is fed to a derandomizing buffer which converts the rapidly and randomly occurring pulses into synchronized and periodically spaced-apart pulses for the accurate counting thereof. Provision is also made for the internal and external disabling of each individual channel of amplifier-discriminators in an ORed plurality of same.

  11. Fast counting electronics for neutron coincidence counting

    DOE Patents [OSTI]

    Swansen, James E.

    1987-01-01

    An amplifier-discriminator is tailored to output a very short pulse upon an above-threshold input from a detector which may be a .sup.3 He detector. The short pulse output is stretched and energizes a light emitting diode (LED) to provide a visual output of operation and pulse detection. The short pulse is further fed to a digital section for processing and possible ORing with other like generated pulses. Finally, the output (or ORed output ) is fed to a derandomizing buffer which converts the rapidly and randomly occurring pulses into synchronized and periodically spaced-apart pulses for the accurate counting thereof. Provision is also made for the internal and external disabling of each individual channel of amplifier-discriminators in an ORed plurality of same.

  12. LOW ENERGY COUNTING CHAMBERS

    DOE Patents [OSTI]

    Hayes, P.M.

    1960-02-16

    A beta particle counter adapted to use an end window made of polyethylene terephthalate was designed. The extreme thinness of the film results in a correspondingly high transmission of incident low-energy beta particles by the window. As a consequence, the counting efficiency of the present counter is over 40% greater than counters using conventional mica end windows.

  13. Pad printer for electronics. Final report

    SciTech Connect (OSTI)

    1998-05-01

    This is the Final report on DARPA-sponsored development Program Pad Printer for Electronics DE-FC04-95AL87486 which was initiated in February, 1995 and intended to run 24 months to February 1997. The Program has significant value to the Thick Film processing industry, an electronic manufacturing alternative for producing functional modules integrated at the multichip level. The result is highly reliable, high volumetric efficiency, subassemblies for military applications and for commercial applications in severe environments, such as automotive, portable communications, and bio-implantable devices. The program progressed quite satisfactorily through 19 months, when it encountered severe, non-technical, difficulties. Resolving these difficulties resulted in several months of delay in completing the Program, but resulted in only a trivial increase in total program cost and no increase in cost to the sponsor. The principle Objective of the Program was the development of a printing system -- machine and appropriate inks -- compatible with existing thick-film processing but offering a 5x improvement in line density. This objective has been met. The Pad Printer is capable of printing suitable inks in traces 25 g wide on 50g centers to a fired thickness of 3 {mu}; each of these parameters is roughly 1/5 the value of the current alternative, silk-screen printing. The available inks represent an assortment of conductor, dielectric, and insulator formulations and the knowledge developed permits extending this family of inks to new and diverse functional materials. An important secondary objective was maximum compatibility with existing Thick Film processing; the printer and ink systems may be substituted directly for the silk screen printers in existing processes. The Program reached or exceeded its other Technical Objectives in almost every case and, in those few instances where the objective was only partially met, work continues under private funding.

  14. Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    Type, PAD District, and Selected States Energy Information Administration Petroleum Marketing Annual 1996 233 Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District,...

  15. Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    Type, PAD District, and Selected States Energy Information Administration Petroleum Marketing Annual 1997 233 Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District,...

  16. Table 4. Estimation Results for PAD District Regions

    U.S. Energy Information Administration (EIA) Indexed Site

    Estimation Results for PAD District Regions Dependent Variable: D(RETPAD1) Dependent Variable: D(RETPAD2) Dependent Variable: D(RETPAD3) Dependent Variable: D(RETPAD4) Dependent...

  17. Prices by Sales Type, PAD District, and Selected States

    U.S. Energy Information Administration (EIA) Indexed Site

    78.5 48.8 See footnotes at end of table. 182 Energy Information AdministrationPetroleum Marketing Annual 1999 Table 39. No. 2 Distillate a Prices by Sales Type, PAD District, and...

  18. Prices by Sales Type, PAD District, and Selected States

    U.S. Energy Information Administration (EIA) Indexed Site

    76.6 45.7 See footnotes at end of table. 182 Energy Information AdministrationPetroleum Marketing Annual 1998 Table 39. No. 2 Distillate a Prices by Sales Type, PAD District, and...

  19. Prices by Sales Type, PAD District, and Selected States

    U.S. Energy Information Administration (EIA) Indexed Site

    52.1 See footnotes at end of table. 224 Energy Information Administration Petroleum Marketing Annual 1995 Table 39. No. 2 Distillate a Prices by Sales Type, PAD District, and...

  20. SEP Success Story: "Green Launching Pad" Supports Clean Energy...

    Broader source: Energy.gov (indexed) [DOE]

    John Lynch, and UNH President Mark Huddleston held at EnerTrac, Inc., in Hudson, NH. | Courtesy of University of New Hampshire Photographic Services Green Launching Pad 2.0 awards ...

  1. Pad polishing for rapid production of large flats

    SciTech Connect (OSTI)

    Berggren, R.R.; Schmell, R.A.

    1997-11-01

    Pad polishing is an efficient technique for polishing-out a ground surface and reaching a figure better than one wave, ready for completion with less than an hour on a planetary polisher. For the 350 mm square piece of BK-7, removal was one micrometer every 10 minutes. Polishing-out from a 5 micrometer grind took less than 3 hours, to a surface smoothness of one nm rms. Other tests verified that the pad leaves no unusual subsurface damage. Following completion on a pitch planetary polisher, surface finish is the same as obtained for conventional processing. Unlike pitch, the pad retains its surface figure, producing a uniform result when used on a production basis. Coupled with the speed of production and low capital cost of overarm machines, it provides a cost-effective approach.

  2. Exposure-rate calibration using large-area calibration pads

    SciTech Connect (OSTI)

    Novak, E.F.

    1988-09-01

    The US Department of Energy (DOE) Office of Remedial Action and Waste Technology established the Technical Measurements Center (TMC) at the DOE Grand Junction Projects Office (GJPO) in Grand Junction, Colorado, to standardize, calibrate, and compare measurements made in support of DOE remedial action programs. A set of large-area, radioelement-enriched concrete pads was constructed by the DOE in 1978 at the Walker Field Airport in Grand Junction for use as calibration standards for airborne gamma-ray spectrometer systems. The use of these pads was investigated by the TMC as potential calibration standards for portable scintillometers employed in measuring gamma-ray exposure rates at Uranium Mill Tailings Remedial Action (UMTRA) project sites. Data acquired on the pads using a pressurized ionization chamber (PIC) and three scintillometers are presented as an illustration of an instrumental calibration. Conclusions and recommended calibration procedures are discussed, based on the results of these data.

  3. Property:EditCount | Open Energy Information

    Open Energy Info (EERE)

    EditCount Jump to: navigation, search Property Name EditCount Property Type Number Description Number of user edits. Pages using the property "EditCount" Showing 25 pages using...

  4. V-141: HP ElitePad 900 Secure Boot Bug Lets Local Users Boot...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1: HP ElitePad 900 Secure Boot Bug Lets Local Users Boot to Other Operating Systems V-141: HP ElitePad 900 Secure Boot Bug Lets Local Users Boot to Other Operating Systems April...

  5. LINEAR COUNT-RATE METER

    DOE Patents [OSTI]

    Henry, J.J.

    1961-09-01

    A linear count-rate meter is designed to provide a highly linear output while receiving counting rates from one cycle per second to 100,000 cycles per second. Input pulses enter a linear discriminator and then are fed to a trigger circuit which produces positive pulses of uniform width and amplitude. The trigger circuit is connected to a one-shot multivibrator. The multivibrator output pulses have a selected width. Feedback means are provided for preventing transistor saturation in the multivibrator which improves the rise and decay times of the output pulses. The multivibrator is connected to a diode-switched, constant current metering circuit. A selected constant current is switched to an averaging circuit for each pulse received, and for a time determined by the received pulse width. The average output meter current is proportional to the product of the counting rate, the constant current, and the multivibrator output pulse width.

  6. FCTO Consortia Overview (HyMARC and FC-PAD) Webinar | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Consortia Overview (HyMARC and FC-PAD) Webinar FCTO Consortia Overview (HyMARC and FC-PAD) Webinar Access the recording and download the presentation slides from the Fuel Cell Technologies Office webinar "FCTO Consortia Overview (HyMARC and FC-PAD)" held on January 7, 2016. FCTO Consortia Overview (HyMARC and FC-PAD) Webinar Slides (7.43 MB) More Documents & Publications FC-PAD Organization and Activities Hydrogen Storage Lab PI Workshop: HyMARC and NREL-Led Characterization Effort

  7. Count-doubling time safety circuit

    DOE Patents [OSTI]

    Rusch, Gordon K.; Keefe, Donald J.; McDowell, William P.

    1981-01-01

    There is provided a nuclear reactor count-factor-increase time monitoring circuit which includes a pulse-type neutron detector, and means for counting the number of detected pulses during specific time periods. Counts are compared and the comparison is utilized to develop a reactor scram signal, if necessary.

  8. Table 42. Residual Fuel Oil Prices by PAD District and State

    Gasoline and Diesel Fuel Update (EIA)

    Information Administration Petroleum Marketing Annual 1995 245 Table 42. Residual Fuel Oil Prices by PAD District and State (Cents per Gallon Excluding Taxes) - Continued...

  9. Table 42. Residual Fuel Oil Prices by PAD District and State

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Information AdministrationPetroleum Marketing Annual 1998 203 Table 42. Residual Fuel Oil Prices by PAD District and State (Cents per Gallon Excluding Taxes) - Continued...

  10. "Green Launching Pad" Supports Clean Energy Small Businesses | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy "Green Launching Pad" Supports Clean Energy Small Businesses "Green Launching Pad" Supports Clean Energy Small Businesses May 24, 2012 - 2:01pm Addthis Green Launching Pad 2.0 awards ceremony with Secretary Chu, Gov. John Lynch, and UNH President Mark Huddleston held at EnerTrac, Inc., in Hudson, NH. | Courtesy of University of New Hampshire Photographic Services Green Launching Pad 2.0 awards ceremony with Secretary Chu, Gov. John Lynch, and UNH President Mark

  11. Table A1. Refiner/Reseller Motor Gasoline Prices by Grade, PAD...

    U.S. Energy Information Administration (EIA) Indexed Site

    Information Administration Petroleum Marketing Annual 1995 Table A1. RefinerReseller Motor Gasoline Prices by Grade, PAD District and State, 1984-Present (Cents per Gallon...

  12. Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    table. 56 Energy Information AdministrationPetroleum Marketing Annual 1998 Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  13. Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    table. 56 Energy Information AdministrationPetroleum Marketing Annual 1999 Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  14. Table A1. Refiner/Reseller Motor Gasoline Prices by Grade, PAD...

    U.S. Energy Information Administration (EIA) Indexed Site

    AdministrationPetroleum Marketing Annual 1999 401 Table A1. RefinerReseller Motor Gasoline Prices by Grade, PAD District and State, 1984-Present (Cents per Gallon...

  15. Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    table. 56 Energy Information Administration Petroleum Marketing Annual 1995 Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  16. Low Background Counting At SNOLAB

    SciTech Connect (OSTI)

    Lawson, Ian; Cleveland, Bruce [SNOLAB, 1039 Regional Rd 24, Lively, ON P3Y 1N2 (Canada)

    2011-04-27

    It is a continuous and ongoing effort to maintain radioactivity in materials and in the environment surrounding most underground experiments at very low levels. These low levels are required so that experiments can achieve the required detection sensitivities for the detection of low-energy neutrinos, searches for dark matter and neutrinoless double-beta decay. SNOLAB has several facilities which are used to determine these low background levels in the materials and the underground environment. This proceedings will describe the SNOLAB High Purity Germanium Detector which has been in continuous use for the past five years and give results of many of the items that have been counted over that period. Brief descriptions of SNOLAB's alpha-beta and electrostatic counters will be given, and the radon levels at SNOLAB will be discussed.

  17. Well coincidence counting and analysis

    SciTech Connect (OSTI)

    Lu, Ming-Shih; Teichmann, T.; Ceo, R.N.; Collins, L.L.

    1994-03-01

    In several recent papers a physical/mathematical model was developed to describe the nuclear multiplicative processes in samples containing fissile material from a general statistical viewpoint, starting with the basic underlying physical phenomena. The results of this model agreed with the established picture used in ``standard`` HLNCC (High Level Neutron Coincidence Counter) measurements, but considerably extended them, and allowed a more detailed interpretation of the underlying physical mechanisms and of the higher moments of the neutron counts. The present paper examines some recent measurements made at Y-12 (Oak Ridge) using the AWCC, in the light of this model. The results show internal consistency under a variety of conditions, and give good agreement between experiment and theory.

  18. Anomalous liquid scintillation counting of chromium-51

    SciTech Connect (OSTI)

    Charig, A.; Blake-Haskins, J.; Eigen, E.

    1985-12-01

    Unusual behavior of chromium-51 in liquid scintillation cocktail is described. Rapidly declining count rate is attributed to first-order binding of chromate to glass vials.

  19. Low Background Counting at LBNL

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Smith, A. R.; Thomas, K. J.; Norman, E. B.; Chan, Y. D.; Lesko, K. T.; Hurley, D. L.

    2015-03-24

    The Low Background Facility (LBF) at Lawrence Berkeley National Laboratory in Berkeley, California provides low background gamma spectroscopy services to a wide array of experiments and projects. The analysis of samples takes place within two unique facilities; locally within a carefully-constructed, low background cave and remotely at an underground location that historically has operated underground in Oroville, CA, but has recently been relocated to the Sanford Underground Research Facility (SURF) in Lead, SD. These facilities provide a variety of gamma spectroscopy services to low background experiments primarily in the form of passive material screening for primordial radioisotopes (U, Th, K)more » or common cosmogenic/anthropogenic products, as well as active screening via Neutron Activation Analysis for specific applications. The LBF also provides hosting services for general R&D testing in low background environments on the surface or underground for background testing of detector systems or similar prototyping. A general overview of the facilities, services, and sensitivities is presented. Recent activities and upgrades will also be presented, such as the completion of a 3π anticoincidence shield at the surface station and environmental monitoring of Fukushima fallout. The LBF is open to any users for counting services or collaboration on a wide variety of experiments and projects.« less

  20. Low Background Counting at LBNL

    SciTech Connect (OSTI)

    Smith, A. R.; Thomas, K. J.; Norman, E. B.; Chan, Y. D.; Lesko, K. T.; Hurley, D. L.

    2015-03-24

    The Low Background Facility (LBF) at Lawrence Berkeley National Laboratory in Berkeley, California provides low background gamma spectroscopy services to a wide array of experiments and projects. The analysis of samples takes place within two unique facilities; locally within a carefully-constructed, low background cave and remotely at an underground location that historically has operated underground in Oroville, CA, but has recently been relocated to the Sanford Underground Research Facility (SURF) in Lead, SD. These facilities provide a variety of gamma spectroscopy services to low background experiments primarily in the form of passive material screening for primordial radioisotopes (U, Th, K) or common cosmogenic/anthropogenic products, as well as active screening via Neutron Activation Analysis for specific applications. The LBF also provides hosting services for general R&D testing in low background environments on the surface or underground for background testing of detector systems or similar prototyping. A general overview of the facilities, services, and sensitivities is presented. Recent activities and upgrades will also be presented, such as the completion of a 3π anticoincidence shield at the surface station and environmental monitoring of Fukushima fallout. The LBF is open to any users for counting services or collaboration on a wide variety of experiments and projects.

  1. Historical Material Analysis of DC745U Pressure Pads

    SciTech Connect (OSTI)

    Ortiz-Acosta, Denisse

    2012-07-30

    As part of the Enhance Surveillance mission, it is the goal to provide suitable lifetime assessment of stockpile materials. This report is an accumulation of historical publication on the DC745U material and their findings. It is the intention that the B61 LEP program uses this collection of data to further develop their understanding and potential areas of study. DC745U is a commercially available silicone elastomer consisting of dimethyl, methyl-phenyl, and methyl-vinyl siloxane repeat units. Originally, this material was manufactured by Dow Corning as Silastic{reg_sign} DC745U at their manufacturing facility in Kendallville, IN. Recently, Dow Corning shifted this material to the Xiameter{reg_sign} brand product line. Currently, DC745U is available through Xiameter{reg_sign} or Dow Corning's distributor R. D. Abbott Company. DC745U is cured using 0.5 wt% vinyl-specific peroxide curing agent known as Luperox 101 or Varox DBPH-50. This silicone elastomer is used in numerous parts, including two major components (outer pressure pads and aft cap support) in the W80 and as pressure pads on the B61. DC745U is a proprietary formulation, thus Dow Corning provides limited information on its composition and properties. Based on past experience with Dow Corning, DC745U is at risk of formulation changes without notification to the costumer. A formulation change for DC745U may have a significant impact because the network structure is a key variable in determining material properties. The purpose of this report is to provide an overview of historical DC745U studies and identify gaps that need to be addressed in future work. Some of the previous studies include the following: 1. Spectroscopic characterization of raw gum stock. 2. Spectroscopic, thermal, and mechanical studies on cured DC745U. 3. Nuclear Magnetic Resonance (NMR) and solvent swelling studies on DC745U with different crosslink densities. 4. NMR, solvent swelling, thermal, and mechanical studies on thermally aged

  2. SEP Success Story: Green Launching Pad Taps Six More Companies for Take-off

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy Green Launching Pad Taps Six More Companies for Take-off SEP Success Story: Green Launching Pad Taps Six More Companies for Take-off April 29, 2011 - 9:58am Addthis Yesterday, U.S. Secretary of Energy Steven Chu joined New Hampshire Governor John Lynch and University of New Hampshire (UNH) President Mark W. Huddleston in announcing the six businesses selected to participate in the second round of the Green Launching Pad. Learn more. Addthis Related Articles Green

  3. Construction and characterization of the TL/TH thorium calibration pads

    SciTech Connect (OSTI)

    Steele, W.D.

    1987-09-01

    The Technical Measurements Center (TMC) was established and was tasked with developing and/or recommending measurement methods for use in support of remedial action programs. Since one aspect of this technical support is the provision of calibration facilities for standardization of field measurements, four sets of thorium-232 enriched pads (two pads per set) were constructed for use by remedial action contractors in calibrating portable field instruments that are used to make direct, in-situ measurements of radium-226, thorium-232, and potassium-40. This report presents the design, construction, and characterization data of the eight calibration pads. 17 refs., 8 figs., 15 tabs.

  4. FC-PAD: Fuel Cell Consortium for Performance and Durability | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy FC-PAD: Fuel Cell Consortium for Performance and Durability FC-PAD: Fuel Cell Consortium for Performance and Durability Illustration of the research consortia model showing a 'National Laboratory Core Team' as the central role with three sub-groups of University & Non-Profit, Industry, and National Lab contributing to the core. The Fuel Cell Consortium for Performance and Durability (FC-PAD) will aid in the understanding of-and lead to significant improvements in-fuel cell

  5. Webinar January 7: FCTO Consortia Overview Webinar (FC-PAD and HyMARC) |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy January 7: FCTO Consortia Overview Webinar (FC-PAD and HyMARC) Webinar January 7: FCTO Consortia Overview Webinar (FC-PAD and HyMARC) January 5, 2016 - 1:39pm Addthis The Fuel Cell Technologies Office will present a live webinar titled "FCTO Consortia Overview Webinar (FC-PAD and HyMARC)" on Thursday, January 7, from 2 to 3 p.m. Eastern Standard Time (EST). To accelerate the rate of progress in developing technologies to improve the performance and durability

  6. Table 3. Estimation Results for National and Sub-PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    Estimation Results for National and Sub-PAD District Regions Dependent Variable: D(RETUS) Dependent Variable: D(RETPAD1X) Dependent Variable: D(RETPAD1Y) Dependent Variable:...

  7. Webinar: FCTO Consortia Overview Webinar (FC-PAD and HyMARC)

    Broader source: Energy.gov [DOE]

    The Fuel Cell Technologies Office will present a live webinar titled “FCTO Consortia Overview Webinar (FC-PAD and HyMARC)” on Thursday, January 7, from 2 to 3 p.m. EST.

  8. Table 42. Residual Fuel Oil Prices by PAD District and State

    Gasoline and Diesel Fuel Update (EIA)

    55.1 47.1 W W 55.1 46.2 See footnotes at end of table. 42. Residual Fuel Oil Prices by PAD District and State Energy Information Administration Petroleum...

  9. Table 42. Residual Fuel Oil Prices by PAD District and State

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    45.5 49.2 W W 44.5 45.4 See footnotes at end of table. 42. Residual Fuel Oil Prices by PAD District and State Energy Information Administration Petroleum...

  10. Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    62.4 65.5 51.3 See footnotes at end of table. Energy Information AdministrationPetroleum Marketing Annual 1999 191 Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District,...

  11. Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    64.6 54.0 See footnotes at end of table. Energy Information Administration Petroleum Marketing Annual 1995 233 Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District,...

  12. Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    60.4 60.0 45.2 See footnotes at end of table. Energy Information AdministrationPetroleum Marketing Annual 1998 191 Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District,...

  13. SEP Success Story: "Green Launching Pad" Supports Clean Energy Small Businesses

    Broader source: Energy.gov [DOE]

    A commercialization partnership funded by the State Energy Program – known as the Green Launching Pad program -- is a joint effort by the New Hampshire Office of Energy and Planning and the University of New Hampshire. Learn more.

  14. Time Variant Floating Mean Counting Algorithm

    Energy Science and Technology Software Center (OSTI)

    1999-06-03

    This software was written to test a time variant floating mean counting algorithm. The algorithm was developed by Westinghouse Savannah River Company and a provisional patent has been filed on the algorithm. The test software was developed to work with the Val Tech model IVB prototype version II count rate meter hardware. The test software was used to verify the algorithm developed by WSRC could be correctly implemented with the vendor''s hardware.

  15. Next Generation Non-particulate Dry Nonwoven Pad for Chemical Warfare Agent Decontamination

    SciTech Connect (OSTI)

    Ramkumar, S S; Love, A; Sata, U R; Koester, C J; Smith, W J; Keating, G A; Hobbs, L; Cox, S B; Lagna, W M; Kendall, R J

    2008-05-01

    New, non-particulate decontamination materials promise to reduce both military and civilian casualties by enabling individuals to decontaminate themselves and their equipment within minutes of exposure to chemical warfare agents or other toxic materials. One of the most promising new materials has been developed using a needlepunching nonwoven process to construct a novel and non-particulate composite fabric of multiple layers, including an inner layer of activated carbon fabric, which is well-suited for the decontamination of both personnel and equipment. This paper describes the development of a composite nonwoven pad and compares efficacy test results for this pad with results from testing other decontamination systems. The efficacy of the dry nonwoven fabric pad was demonstrated specifically for decontamination of the chemical warfare blister agent bis(2-chloroethyl)sulfide (H or sulfur mustard). GC/MS results indicate that the composite fabric was capable of significantly reducing the vapor hazard from mustard liquid absorbed into the nonwoven dry fabric pad. The mustard adsorption efficiency of the nonwoven pad was significantly higher than particulate activated carbon (p=0.041) and was similar to the currently fielded US military M291 kit (p=0.952). The nonwoven pad has several advantages over other materials, especially its non-particulate, yet flexible, construction. This composite fabric was also shown to be chemically compatible with potential toxic and hazardous liquids, which span a range of hydrophilic and hydrophobic chemicals, including a concentrated acid, an organic solvent and a mild oxidant, bleach.

  16. FLOP Counts for "Small" Single-Node Miniapplication Tests

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    FLOP Counts for "Small" Single-Node Miniapplication Tests FLOP Counts for "Small" Single-Node Miniapplication Tests These data, obtained using the NERSC Hopper system, are provided...

  17. Photon-counting solid-state photomultiplier

    SciTech Connect (OSTI)

    Petroff, M.D.; Stapelbroek, M.G.

    1989-02-01

    The Solid-State Photomultiplier is a silicon device capable of continuous detection of individual photons in the wave length range from 0.4 to 28 ..mu..m. Operated with an applied bias near 7 volts the device responds to the absorption of an incident photon with a submicrosecond-rise-time current pulse with a narrow amplitude distribution well above the electronic readout noise level. Optimal photon-counting performance occurs between 6 and 10 K and for count rates less than 10/sup 10/ counts/s per cm/sup 2/ of detector area. A 60% counting quantum efficiency has been demonstrated at 20 ..mu..m, and near 60% was observed in the visible light region. The underlying mechanism involves extremely fast internal charge amplification by impact ionization of impurity-band electrons and results in a pulse for each photoelectrically or thermally induced free carrier. The thermally induced dark pulse rate at 7 K is sufficiently low that background limited detector performance is obtained at a background of less than 10/sup 6/ photons/cm/sup 2/s.

  18. Differential white cell count by centrifugal microfluidics.

    SciTech Connect (OSTI)

    Sommer, Gregory Jon; Tentori, Augusto M.; Schaff, Ulrich Y.

    2010-07-01

    We present a method for counting white blood cells that is uniquely compatible with centrifugation based microfluidics. Blood is deposited on top of one or more layers of density media within a microfluidic disk. Spinning the disk causes the cell populations within whole blood to settle through the media, reaching an equilibrium based on the density of each cell type. Separation and fluorescence measurement of cell types stained with a DNA dye is demonstrated using this technique. The integrated signal from bands of fluorescent microspheres is shown to be proportional to their initial concentration in suspension. Among the current generation of medical diagnostics are devices based on the principle of centrifuging a CD sized disk functionalized with microfluidics. These portable 'lab on a disk' devices are capable of conducting multiple assays directly from a blood sample, embodied by platforms developed by Gyros, Samsung, and Abaxis. [1,2] However, no centrifugal platform to date includes a differential white blood cell count, which is an important metric complimentary to diagnostic assays. Measuring the differential white blood cell count (the relative fraction of granulocytes, lymphocytes, and monocytes) is a standard medical diagnostic technique useful for identifying sepsis, leukemia, AIDS, radiation exposure, and a host of other conditions that affect the immune system. Several methods exist for measuring the relative white blood cell count including flow cytometry, electrical impedance, and visual identification from a stained drop of blood under a microscope. However, none of these methods is easily incorporated into a centrifugal microfluidic diagnostic platform.

  19. Construction and characterization of the RH/RL radium calibration pads

    SciTech Connect (OSTI)

    Steele, W.D.; Marutzky, S.J.; Dickerson, J.W.

    1989-01-01

    The US Department of Energy (DOE) Office of Remedial Action and Waste Technology has as one of its goals the standardization of field measurements made by its remedial action contractors throughout the country. In support of this goal, the Technical Measurements Center (TMC) was established at the DOE Grand Junction Projects Office (GJPO) Facility, and was tasked with developing and/or recommending measurement methods for use in support of remedial action programs. One aspect of this technical support is the provision of calibration facilities for standardization of field measurements. The report presents the results of the design, construction, and characterization of 14 calibration pads enriched in radium-226. The 14 pads comprise 7 sets with a high and low activity pad in each set. The pads are concrete cylinders, approximately 5 feet in diameter by 2 feet in height. They are intended for use in calibrating portable field instruments that are used by remedial action contractors to make direct, in situ measurements of radium-226, thorium-232, and potassium-40. 23 refs., 6 figs., 14 tabs.

  20. Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    82.4 77.1 68.9 62.6 71.6 92.3 89.9 82.6 72.7 - 78.2 See footnotes at end of table. 31. Motor Gasoline Prices by Grade, Sales Type, PAD District, and State 56 Energy Information...

  1. Table A1. Refiner/Reseller Motor Gasoline Prices by Grade, PAD...

    U.S. Energy Information Administration (EIA) Indexed Site

    71.6 92.3 78.2 101.8 83.6 87.5 74.7 See footnotes at end of table. A1. RefinerReseller Motor Gasoline Prices by Grade, PAD District, and State, 1984-Present 452 Energy Information...

  2. Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    82.5 75.1 68.6 62.0 70.7 92.7 90.7 81.5 72.8 - 78.0 See footnotes at end of table. 31. Motor Gasoline Prices by Grade, Sales Type, PAD District, and State 56 Energy Information...

  3. Alternative Fuels Data Center: Alternative Fueling Station Counts by State

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    Locate Stations Printable Version Share this resource Send a link to Alternative Fuels Data Center: Alternative Fueling Station Counts by State to someone by E-mail Share Alternative Fuels Data Center: Alternative Fueling Station Counts by State on Facebook Tweet about Alternative Fuels Data Center: Alternative Fueling Station Counts by State on Twitter Bookmark Alternative Fuels Data Center: Alternative Fueling Station Counts by State on Google Bookmark Alternative Fuels Data Center:

  4. Active neutron multiplicity counting of bulk uranium

    SciTech Connect (OSTI)

    Ensslin, N.; Krick, M.S.; Langner, D.G.; Miller, M.C. )

    1991-01-01

    This paper describes a new nondestructive assay technique being developed to assay bulk uranium containing kilogram quantities of {sup 235}U. The new technique uses neutron multiplicity analysis of data collected with a coincidence counter outfitted with AmLi neutron sources. The authors have calculated the expected neutron multiplicity count rate and assay precision for this technique and will report on its expected performance as a function of detector design characteristics, {sup 235}U sample mass, AmLi source strength, and source-to-sample coupling.

  5. Net Movements of Crude Oil and Petroleum Products by Pipeline, Tanker, Barge, and Rail Between PAD Districts, January 2014

    U.S. Energy Information Administration (EIA) Indexed Site

    January 2014 (Thousand Barrels) Commodity PAD District 1 PAD District 2 PAD District 3 Receipts Shipments Net Receipts Receipts Shipments Net Receipts Receipts Shipments Net Receipts Crude Oil 1 ................................................................ 11,209 1,213 9,996 35,554 35,363 190 23,680 28,598 -4,918 Petroleum Products 2 .............................................. 106,990 8,669 107,347 29,831 18,055 -6,599 16,594 124,991 -103,885 Pentanes Plus

  6. Low background counting techniques at SNOLAB

    SciTech Connect (OSTI)

    Lawson, Ian; Cleveland, Bruce [SNOLAB, 1039 Regional Rd 24, Lively, ON P3Y 1N2 (Canada)] [SNOLAB, 1039 Regional Rd 24, Lively, ON P3Y 1N2 (Canada)

    2013-08-08

    Many of the experiments currently searching for dark matter, studying properties of neutrinos or searching for neutrinoless double beta decay require very low levels of radioactive backgrounds both in their own construction materials and in the surrounding environment. These low background levels are required so that the experiments can achieve the required sensitivities for their searches. SNOLAB has several facilities which are used to directly measure these radioactive backgrounds. This proceedings will describe SNOLAB's High Purity Germanium Detectors, one of which has been in continuous use for the past seven years measuring materials for many experiments in operation or under construction at SNOLAB. A description of the characterisation of SNOLAB's new germanium well detector will be presented. In addition, brief descriptions of SNOLAB's alpha-beta and electrostatic counters will be presented and a description of SNOLAB's future low background counting laboratory will be given.

  7. L-connect routing of die surface pads to the die edge for stacking in a 3D array

    DOE Patents [OSTI]

    Petersen, Robert W.

    2000-01-01

    Integrated circuit chips and method of routing the interface pads from the face of the chip or die to one or more sidewall surfaces of the die. The interconnection is routed from the face of the die to one or more edges of the die, then routed over the edge of the die and onto the side surface. A new pad is then formed on the sidewall surface, which allows multiple die or chips to be stacked in a three-dimensional array, while enabling follow-on signal routing from the sidewall pads. The routing of the interconnects and formation of the sidewall pads can be carried out in an L-connect or L-shaped routing configuration, using a metalization process such as laser pantography.

  8. Absolute nuclear material assay using count distribution (LAMBDA) space

    DOE Patents [OSTI]

    Prasad, Mano K.; Snyderman, Neal J.; Rowland, Mark S.

    2015-12-01

    A method of absolute nuclear material assay of an unknown source comprising counting neutrons from the unknown source and providing an absolute nuclear material assay utilizing a model to optimally compare to the measured count distributions. In one embodiment, the step of providing an absolute nuclear material assay comprises utilizing a random sampling of analytically computed fission chain distributions to generate a continuous time-evolving sequence of event-counts by spreading the fission chain distribution in time.

  9. Absolute nuclear material assay using count distribution (LAMBDA) space

    DOE Patents [OSTI]

    Prasad, Manoj K.; Snyderman, Neal J.; Rowland, Mark S.

    2012-06-05

    A method of absolute nuclear material assay of an unknown source comprising counting neutrons from the unknown source and providing an absolute nuclear material assay utilizing a model to optimally compare to the measured count distributions. In one embodiment, the step of providing an absolute nuclear material assay comprises utilizing a random sampling of analytically computed fission chain distributions to generate a continuous time-evolving sequence of event-counts by spreading the fission chain distribution in time.

  10. Optical People Counting for Demand Controlled Ventilation: A...

    Office of Scientific and Technical Information (OSTI)

    of Counter Performance Citation Details In-Document Search Title: Optical People Counting for Demand Controlled Ventilation: A Pilot Study of Counter Performance This pilot ...

  11. Counting small RNA in disease-causing organisms

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    in disease-causing organisms Los Alamos researchers demonstrated improved technical methods capable of directly counting small RNA molecules in pathogenic (disease-causing)...

  12. When DNA Needs to Stand Up and Be Counted

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    biomolecules must be properly oriented to perform their biological function. In other words, the DNA literally must stand up to be counted. Understanding both the attachment...

  13. First AID (Atom counting for Isotopic Determination).

    SciTech Connect (OSTI)

    Roach, J. L.; Israel, K. M.; Steiner, R. E.; Duffy, C. J.; Roench, F. R.

    2002-01-01

    Los Alamos National Laboratory (LANL) has established an in vitro bioassay monitoring program in compliance with the requirements in the Code of Federal Regulations, 10 CFR 835, Occupational Radiation Protection. One aspect of this program involves monitoring plutonium levels in at-risk workers. High-risk workers are monitored using the ultra-sensitive Therrnal Ionization Mass Spectrometry (TIMS) technique to ensure compliance with DOE standards. TIMS is used to measure atom ratios of 239Pua nd 240Puw ith respect to a tracer isotope ('Pu). These ratios are then used to calculate the amount of 239Pu and 240Pup resent. This low-level atom counting technique allows the calculation of the concentration levels of 239Pu and 240Pu in urine for at risk workers. From these concentration levels, dose assessments can be made and worker exposure levels can be monitored. Detection limits for TIMS analysis are on the order of millions of atoms, which translates to activity levels of 150 aCi 239Pua nd 500 aCi for 240Pu. pCi for Our poster presentation will discuss the ultra-sensitive, low-level analytical technique used to measure plutonium isotopes and the data verification methods used for validating isotopic measurements.

  14. When DNA Needs to Stand Up and Be Counted

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    When DNA Needs to Stand Up and Be Counted When DNA Needs to Stand Up and Be Counted Print Wednesday, 31 May 2006 00:00 DNA microarrays are small metal, glass, or silicon chips covered with patterns of short single-stranded DNA (ssDNA). These "DNA chips" are revolutionizing biotechnology, allowing scientists to identify and count many DNA sequences simultaneously. They are the enabling technology for genomic-based medicine and are a critical component of advanced diagnostic systems for

  15. Galaxy number counts to second order and their bispectrum

    SciTech Connect (OSTI)

    Dio, Enea Di; Durrer, Ruth; Marozzi, Giovanni; Montanari, Francesco E-mail: Ruth.Durrer@unige.ch E-mail: Francesco.Montanari@unige.ch

    2014-12-01

    We determine the number counts to second order in cosmological perturbation theory in the Poisson gauge and allowing for anisotropic stress. The calculation is performed using an innovative approach based on the recently proposed ''geodesic light-cone'' gauge. This allows us to determine the number counts in a purely geometric way, without using Einstein's equation. The result is valid for general dark energy models and (most) modified gravity models. We then evaluate numerically some relevant contributions to the number counts bispectrum. In particular we consider the terms involving the density, redshift space distortion and lensing.

  16. Closure Report for Corrective Action Unit 224: Decon Pad and Septic Systems, Nevada Test Site, Nevada

    SciTech Connect (OSTI)

    NSTec Environmental Restoration

    2007-10-01

    Corrective Action Unit (CAU) 224 is located in Areas 02, 03, 05, 06, 11, and 23 of the Nevada Test Site, which is situated approximately 65 miles northwest of Las Vegas, Nevada. CAU 224 is listed in the Federal Facility Agreement and Consent Order (FFACO) of 1996 as Decon Pad and Septic Systems and is comprised of the following nine Corrective Action Sites (CASs): CAS 02-04-01, Septic Tank (Buried); CAS 03-05-01, Leachfield; CAS 05-04-01, Septic Tanks (4)/Discharge Area; CAS 06-03-01, Sewage Lagoons (3); CAS 06-05-01, Leachfield; CAS 06-17-04, Decon Pad and Wastewater Catch; CAS 06-23-01, Decon Pad Discharge Piping; CAS 11-04-01, Sewage Lagoon; and CAS 23-05-02, Leachfield. The Nevada Division of Environmental Protection (NDEP)-approved corrective action alternative for CASs 02-04-01, 03-05-01, 06-03-01, 11-04-01, and 23-05-02 is no further action. As a best management practice, the septic tanks and distribution box were removed from CASs 02-04-01 and 11-04-01 and disposed of as hydrocarbon waste. The NDEP-approved correction action alternative for CASs 05-04-01, 06-05-01, 06-17-04, and 06-23-01 is clean closure. Closure activities for these CASs included removing and disposing of radiologically and pesticide-impacted soil and debris. CAU 224 was closed in accordance with the NDEP-approved CAU 224 Corrective Action Plan (CAP). The closure activities specified in the CAP were based on the recommendations presented in the CAU 224 Corrective Action Decision Document (U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, 2005). This Closure Report documents CAU 224 closure activities. During closure activities, approximately 60 cubic yards (yd3) of mixed waste in the form of soil and debris; approximately 70 yd{sup 3} of sanitary waste in the form of soil, liquid from septic tanks, and concrete debris; approximately 10 yd{sup 3} of hazardous waste in the form of pesticide-impacted soil; approximately 0.5 yd{sup 3} of universal waste in

  17. Correlated neutron counting for the 21st century

    SciTech Connect (OSTI)

    Evans, Louise G

    2010-12-01

    Correlated neutron counting techniques, such as neutron coincidence and multiplicity counting, are widely employed at nuclear fuel cycle facilities for the accountancy of nuclear material such as plutonium. These techniques need to be improved and enhanced to meet the challenges of complex measurement items and future nuclear safeguards applications, for example; the non-destructive assay of spent nuclear fuel, high counting rate applications, small sample measurements, and Helium-3 replacement. At the same time simulation tools, used for the design of detection systems based on these techniques, are being developed in anticipation of future needs. This seminar will present the theory and current state of the practice of temporally correlated neutron counting. A range of future safeguards applications will then be presented in the context of research projects at Los Alamos National Laboratory.

  18. Multianode cylindrical proportional counter for high count rates

    DOE Patents [OSTI]

    Hanson, James A.; Kopp, Manfred K.

    1981-01-01

    A cylindrical, multiple-anode proportional counter is provided for counting of low-energy photons (<60 keV) at count rates of greater than 10.sup.5 counts/sec. A gas-filled proportional counter cylinder forming an outer cathode is provided with a central coaxially disposed inner cathode and a plurality of anode wires disposed in a cylindrical array in coaxial alignment with and between the inner and outer cathodes to form a virtual cylindrical anode coaxial with the inner and outer cathodes. The virtual cylindrical anode configuration improves the electron drift velocity by providing a more uniform field strength throughout the counter gas volume, thus decreasing the electron collection time following the detection of an ionizing event. This avoids pulse pile-up and coincidence losses at these high count rates. Conventional RC position encoding detection circuitry may be employed to extract the spatial information from the counter anodes.

  19. Multianode cylindrical proportional counter for high count rates

    DOE Patents [OSTI]

    Hanson, J.A.; Kopp, M.K.

    1980-05-23

    A cylindrical, multiple-anode proportional counter is provided for counting of low-energy photons (< 60 keV) at count rates of greater than 10/sup 5/ counts/sec. A gas-filled proportional counter cylinder forming an outer cathode is provided with a central coaxially disposed inner cathode and a plurality of anode wires disposed in a cylindrical array in coaxial alignment with and between the inner and outer cathodes to form a virtual cylindrical anode coaxial with the inner and outer cathodes. The virtual cylindrical anode configuration improves the electron drift velocity by providing a more uniform field strength throughout the counter gas volume, thus decreasing the electron collection time following the detection of an ionizing event. This avoids pulse pile-up and coincidence losses at these high count rates. Conventional RC position encoding detection circuitry may be employed to extract the spatial information from the counter anodes.

  20. Gathering total items count for pagination | OpenEI Community

    Open Energy Info (EERE)

    Gathering total items count for pagination Home > Groups > Utility Rate Hi I'm using the following base link plus some restrictions to sector, utility, and locations to poll for...

  1. When DNA Needs to Stand Up and Be Counted

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    stand up to be counted. Understanding both the attachment and orientation of DNA on gold surfaces was the goal of recent experiments performed at ALS Beamline 8.0.1 by an...

  2. When DNA Needs to Stand Up and Be Counted

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    When DNA Needs to Stand Up and Be Counted Print DNA microarrays are small metal, glass, or silicon chips covered with patterns of short single-stranded DNA (ssDNA). These "DNA chips" are revolutionizing biotechnology, allowing scientists to identify and count many DNA sequences simultaneously. They are the enabling technology for genomic-based medicine and are a critical component of advanced diagnostic systems for medical and homeland security applications. Like digital chips, DNA

  3. When DNA Needs to Stand Up and Be Counted

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    When DNA Needs to Stand Up and Be Counted Print DNA microarrays are small metal, glass, or silicon chips covered with patterns of short single-stranded DNA (ssDNA). These "DNA chips" are revolutionizing biotechnology, allowing scientists to identify and count many DNA sequences simultaneously. They are the enabling technology for genomic-based medicine and are a critical component of advanced diagnostic systems for medical and homeland security applications. Like digital chips, DNA

  4. Students Count -- From the Classroom to the Conference | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Count -- From the Classroom to the Conference Students Count -- From the Classroom to the Conference January 18, 2012 - 5:42pm Addthis Secretary Chu and former Governor of California Arnold Schwarzenegger speak with students at the 2011 Energy Innovation Summit. | Photo courtesy of ARPA-E. Secretary Chu and former Governor of California Arnold Schwarzenegger speak with students at the 2011 Energy Innovation Summit. | Photo courtesy of ARPA-E. Alexa McClanahan Communications Support

  5. When DNA Needs to Stand Up and Be Counted

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    When DNA Needs to Stand Up and Be Counted Print DNA microarrays are small metal, glass, or silicon chips covered with patterns of short single-stranded DNA (ssDNA). These "DNA chips" are revolutionizing biotechnology, allowing scientists to identify and count many DNA sequences simultaneously. They are the enabling technology for genomic-based medicine and are a critical component of advanced diagnostic systems for medical and homeland security applications. Like digital chips, DNA

  6. Counting Down to the Collegiate Wind Competition 2016 | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Counting Down to the Collegiate Wind Competition 2016 Counting Down to the Collegiate Wind Competition 2016 May 19, 2016 - 10:15am Addthis Competitors test their turbines in a wind tunnel at the Collegiate Wind Competition 2015, held at the National Renewable Energy Laboratory's National Wind Technology Center just south of Boulder, Colorado. (Photo by Dennis Schroeder / NREL) Competitors test their turbines in a wind tunnel at the Collegiate Wind Competition 2015, held at the

  7. Thermal neutron detection using a silicon pad detector and {sup 6}LiF removable converters

    SciTech Connect (OSTI)

    Barbagallo, Massimo; Cosentino, Luigi; Marchetta, Carmelo; Pappalardo, Alfio; Scire, Carlotta; Scire, Sergio; Schillaci, Maria; Vecchio, Gianfranco; Finocchiaro, Paolo; Forcina, Vittorio; Peerani, Paolo; Vaccaro, Stefano

    2013-03-15

    A semiconductor detector coupled with a neutron converter is a good candidate for neutron detection, especially for its compactness and reliability if compared with other devices, such as {sup 3}He tubes, even though its intrinsic efficiency is rather lower. In this paper we show a neutron detector design consisting of a 3 cm Multiplication-Sign 3 cm silicon pad detector coupled with one or two external {sup 6}LiF layers, enriched in {sup 6}Li at 95%, placed in contact with the Si active surfaces. This prototype, first characterized and tested at INFN Laboratori Nazionali del Sud and then at JRC Ispra, was successfully shown to detect thermal neutrons with the expected efficiency and an outstanding gamma rejection capability.

  8. Compensated count-rate circuit for radiation survey meter

    DOE Patents [OSTI]

    Todd, Richard A.

    1981-01-01

    A count-rate compensating circuit is provided which may be used in a portable Geiger-Mueller (G-M) survey meter to ideally compensate for counting loss errors in the G-M tube detector. In a G-M survey meter, wherein the pulse rate from the G-M tube is converted into a pulse rate current applied to a current meter calibrated to indicate dose rate, the compensated circuit generates and controls a reference voltage in response to the rate of pulses from the detector. This reference voltage is gated to the current-generating circuit at a rate identical to the rate of pulses coming from the detector so that the current flowing through the meter is varied in accordance with both the frequency and amplitude of the reference voltage pulses applied thereto so that the count rate is compensated ideally to indicate a true count rate within 1% up to a 50% duty cycle for the detector. A positive feedback circuit is used to control the reference voltage so that the meter output tracks true count rate indicative of the radiation dose rate.

  9. Photon counting spectroscopy as done with a Thomson scattering diagnostic

    SciTech Connect (OSTI)

    Den Hartog, D.J.; Ruppert, D.E.

    1993-11-01

    The measurement and reduction of photon counting spectral data is demonstrated within the context of a Thomson scattering diagnostic. This diagnostic contains a microchannel plate (MCP) photomultiplier tube (PMT) as the photon sensing device. The MCP PMT is not an ideal photon sensor, the loss of photoelectrons at the MCP input and the broad charge pulse distribution at the output add to the uncertainty in recorded data. Computer simulations are used to demonstrate an approach to quantification of this added uncertainty and to develop an understanding of its source; the methodology may be applicable to the development of an understanding of photon detectors other than an MCP PMT. Emphasis is placed on the Poisson statistical character of the data, because the assumption that a Gaussian probability distribution is a reasonable statistical description of photon counting data is often questionable. When the count rate is low, the product the possible number of photon counts and the probability of measurement of a single photon is usually not sufficiently large to justify Gaussian statistics. Rather, because probabilities of measurement are so low, the Poisson probability distribution best quantifies the inherent statistical fluctuations in such counting measurements. The method of maximum likelihood is applied to derive the Poisson statistics equivalent of {sub X}{sup 2}. A Poisson statistics based data fitting code is implemented using the Newton-Raphson method of multi-dimensional root finding; we also demonstrate an algorithm to estimate the uncertainties in derived quantities.

  10. Compensated count-rate circuit for radiation survey meter

    DOE Patents [OSTI]

    Todd, R.A.

    1980-05-12

    A count-rate compensating circuit is provided which may be used in a portable Geiger-Mueller (G-M) survey meter to ideally compensate for couting loss errors in the G-M tube detector. In a G-M survey meter, wherein the pulse rate from the G-M tube is converted into a pulse rate current applied to a current meter calibrated to indicate dose rate, the compensation circuit generates and controls a reference voltage in response to the rate of pulses from the detector. This reference voltage is gated to the current-generating circuit at a rate identical to the rate of pulses coming from the detector so that the current flowing through the meter is varied in accordance with both the frequency and amplitude of the reference voltage pulses applied thereto so that the count rate is compensated ideally to indicate a true count rate within 1% up to a 50% duty cycle for the detector. A positive feedback circuit is used to control the reference voltage so that the meter output tracks true count rate indicative of the radiation dose rate.

  11. MEMS packaging with etching and thinning of lid wafer to form lids and expose device wafer bond pads

    SciTech Connect (OSTI)

    Chanchani, Rajen; Nordquist, Christopher; Olsson, Roy H; Peterson, Tracy C; Shul, Randy J; Ahlers, Catalina; Plut, Thomas A; Patrizi, Gary A

    2013-12-03

    In wafer-level packaging of microelectromechanical (MEMS) devices a lid wafer is bonded to a MEMS wafer in a predermined aligned relationship. Portions of the lid wafer are removed to separate the lid wafer into lid portions that respectively correspond in alignment with MEMS devices on the MEMS wafer, and to expose areas of the MEMS wafer that respectively contain sets of bond pads respectively coupled to the MEMS devices.

  12. Acquisition Guide Chapters 4.1- Procurement and Assistance Data System (PADS) and 4.3- Requirements for the Industry Interactive Procurement System (IIPS)

    Broader source: Energy.gov [DOE]

    With the implementation of Strategic Integrated Procurement Enterprise System (STRIPES), Acquisition Guide Chapters 4.1 - Procurement and Assistance Data System (PADS) and 4.3 - Requirements for the Industry Interactive Procurement System (IIPS) are hereby rescinded.

  13. It's the little things that count | National Nuclear Security

    National Nuclear Security Administration (NNSA)

    Administration | (NNSA) It's the little things that count April 16, 2012 OAK RIDGE, Tenn. -- In just five months, the Jack Case Center at the National Nuclear Security Administration's Y-12 National Security Complex has not only achieved compliance with a national building standard for energy sustainability, but has also accomplished a 21.4 percent reduction in energy consumption. File It's the little things th

  14. Modeling patterns in count data using loglinear and related models

    SciTech Connect (OSTI)

    Atwood, C.L.

    1995-12-01

    This report explains the use of loglinear and logit models, for analyzing Poisson and binomial counts in the presence of explanatory variables. The explanatory variables may be unordered categorical variables or numerical variables, or both. The report shows how to construct models to fit data, and how to test whether a model is too simple or too complex. The appropriateness of the methods with small data sets is discussed. Several example analyses, using the SAS computer package, illustrate the methods.

  15. Development of Counted Single Donor Devices using in-situ Single...

    Office of Scientific and Technical Information (OSTI)

    Development of Counted Single Donor Devices using in-situ Single Ion Detectors on the SNL NanoImplanter. Citation Details In-Document Search Title: Development of Counted Single ...

  16. FTCP-08-001, Methodology for Counting TQP Personnel and Qualifications...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1, Methodology for Counting TQP Personnel and Qualifications FTCP-08-001, Methodology for Counting TQP Personnel and Qualifications FTCP Issue Paper: FTCP-08-001 Approved by FTCP, ...

  17. Learning How to Count: A High Multiplicity Search for the LHC...

    Office of Scientific and Technical Information (OSTI)

    Learning How to Count: A High Multiplicity Search for the LHC Citation Details In-Document Search Title: Learning How to Count: A High Multiplicity Search for the LHC Authors:...

  18. Neutron counting and gamma spectroscopy with PVT detectors.

    SciTech Connect (OSTI)

    Mitchell, Dean James; Brusseau, Charles A.

    2011-06-01

    Radiation portals normally incorporate a dedicated neutron counter and a gamma-ray detector with at least some spectroscopic capability. This paper describes the design and presents characterization data for a detection system called PVT-NG, which uses large polyvinyl toluene (PVT) detectors to monitor both types of radiation. The detector material is surrounded by polyvinyl chloride (PVC), which emits high-energy gamma rays following neutron capture reactions. Assessments based on high-energy gamma rays are well suited for the detection of neutron sources, particularly in border security applications, because few isotopes in the normal stream of commerce have significant gamma ray yields above 3 MeV. Therefore, an increased count rate for high-energy gamma rays is a strong indicator for the presence of a neutron source. The sensitivity of the PVT-NG sensor to bare {sup 252}Cf is 1.9 counts per second per nanogram (cps/ng) and the sensitivity for {sup 252}Cf surrounded by 2.5 cm of polyethylene is 2.3 cps/ng. The PVT-NG sensor is a proof-of-principal sensor that was not fully optimized. The neutron detector sensitivity could be improved, for instance, by using additional moderator. The PVT-NG detectors and associated electronics are designed to provide improved resolution, gain stability, and performance at high-count rates relative to PVT detectors in typical radiation portals. As well as addressing the needs for neutron detection, these characteristics are also desirable for analysis of the gamma-ray spectra. Accurate isotope identification results were obtained despite the common impression that the absence of photopeaks makes data collected by PVT detectors unsuitable for spectroscopic analysis. The PVT detectors in the PVT-NG unit are used for both gamma-ray and neutron detection, so the sensitive volume exceeds the volume of the detection elements in portals that use dedicated components to detect each type of radiation.

  19. Optimal gate-width setting for passive neutrons multiplicity counting

    SciTech Connect (OSTI)

    Croft, Stephen; Evans, Louise G; Schear, Melissa A

    2010-01-01

    When setting up a passive neutron coincidence counter it is natural to ask what coincidence gate settings should be used to optimize the counting precision. If the gate width is too short then signal is lost and the precision is compromised because in a given period only a few coincidence events will be observed. On the other hand if the gate is too large the signal will be maximized but it will also be compromised by the high level of random pile-up or Accidental coincidence events which must be subtracted. In the case of shift register electronics connected to an assay chamber with an exponential dieaway profile operating in the regime where the Accidentals rate dominates the Reals coincidence rate but where dead-time is not a concern, simple arguments allow one to show that the relative precision on the net Reals rate is minimized when the coincidence gate is set to about 1.2 times the lie dieaway time of the system. In this work we show that making the same assumptions it is easy to show that the relative precision on the Triples rates is also at a minimum when the relative precision of the Doubles (or Reals) is at a minimum. Although the analysis is straightforward to our knowledge such a discussion has not been documented in the literature before. Actual measurement systems do not always behave in the ideal we choose to model them. Fortunately however the variation in the relative precision as a function of gate width is rather flat for traditional safeguards counters and so the performance is somewhat forgiving of the exact choice. The derivation further serves to delineate the important parameters which determine the relative counting precision of the Doubles and Triples rates under the regime considered. To illustrate the similarities and differences we consider the relative standard deviation that might be anticipated for a passive correlation count of an axial section of a spent nuclear fuel assembly under practically achievable conditions.

  20. Los Alamos Middle School team wins regional MathCounts competition

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Los Alamos Middle School team wins Regional MathCounts competition Community Connections: Your link to news and opportunities from Los Alamos National Laboratory Latest Issue: September 1, 2016 all issues All Issues » submit Los Alamos Middle School wins regional MathCounts event Competes against 60 other middle schools for the title. March 1, 2013 Los Alamos Middle School won the regional MathCounts competition. Los Alamos Middle School won the regional MathCounts competition. Contacts Editor

  1. Metals processing control by counting molten metal droplets

    DOE Patents [OSTI]

    Schlienger, Eric; Robertson, Joanna M.; Melgaard, David; Shelmidine, Gregory J.; Van Den Avyle, James A.

    2000-01-01

    Apparatus and method for controlling metals processing (e.g., ESR) by melting a metal ingot and counting molten metal droplets during melting. An approximate amount of metal in each droplet is determined, and a melt rate is computed therefrom. Impedance of the melting circuit is monitored, such as by calculating by root mean square a voltage and current of the circuit and dividing the calculated current into the calculated voltage. Analysis of the impedance signal is performed to look for a trace characteristic of formation of a molten metal droplet, such as by examining skew rate, curvature, or a higher moment.

  2. Optical People Counting for Demand Controlled Ventilation: A Pilot Study of Counter Performance

    SciTech Connect (OSTI)

    Fisk, William J.; Sullivan, Douglas

    2009-12-26

    This pilot scale study evaluated the counting accuracy of two people counting systems that could be used in demand controlled ventilation systems to provide control signals for modulating outdoor air ventilation rates. The evaluations included controlled challenges of the people counting systems using pre-planned movements of occupants through doorways and evaluations of counting accuracies when naive occupants (i.e., occupants unaware of the counting systems) passed through the entrance doors of the building or room. The two people counting systems had high counting accuracy accuracies, with errors typically less than 10percent, for typical non-demanding counting events. However, counting errors were high in some highly challenging situations, such as multiple people passing simultaneously through a door. Counting errors, for at least one system, can be very high if people stand in the field of view of the sensor. Both counting system have limitations and would need to be used only at appropriate sites and where the demanding situations that led to counting errors were rare.

  3. Radiological Survey Tool Set for ArcGIS 8.3 and ArcPad 6.0

    SciTech Connect (OSTI)

    ROGER, COTTRELL

    2004-11-30

    The Radiological Control Operations (RCO) group at the Savannah River Site (SRS) is tasked with conducting routine surveys for the detection of radiological contaminants in the environment. The Radiological Survey Tool Set (RSTS) was developed by the Environmental & Geographic Information Systems (EGIS) group of SRS to assist RCO personnel in this survey process. The tool set consists of two major components. The first component is a custom extension for ArcGIS 8.3 that allows the user to interactively create a sampling plan prior to entering the field. Additionally, the extension allows the user to upload field-collected data to the GIS with post-processing functionality. The second component is a custom ArcPad 6.0 applet. This applet provides the user with navigational capabilities to a selected origin point with the help of Global Positioning Systems (GPS) technology, and the recording of the sample data results into a hand-held field computer via ArcPad 6.0 software.

  4. ,"Total Crude Oil and Petroleum Products Net Receipts by Pipeline, Tanker, Barge and Rail between PAD Districts"

    U.S. Energy Information Administration (EIA) Indexed Site

    Net Receipts by Pipeline, Tanker, Barge and Rail between PAD Districts" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description","# Of Series","Frequency","Latest Data for" ,"Data 1","Total Crude Oil and Petroleum Products Net Receipts by Pipeline, Tanker, Barge and Rail between PAD Districts",5,"Monthly","6/2016","1/15/1981" ,"Release

  5. Active Well Counting Using New PSD Plastic Detectors

    SciTech Connect (OSTI)

    Hausladen, Paul; Newby, Jason; McElroy, Robert Dennis

    2015-11-01

    This report presents results and analysis from a series of proof-of-concept measurements to assess the suitability of segmented detectors constructed from Eljen EJ-299-34 PSD-plastic scintillator with pulse-shape discrimination capability for the purposes of quantifying uranium via active neutron coincidence counting. Present quantification of bulk uranium materials for international safeguards and domestic materials control and accounting relies on active neutron coincidence counting systems, such as the Active Well Coincidence Counter (AWCC) and the Uranium Neutron Coincidence Collar (UNCL), that use moderated He-3 proportional counters along with necessarily low-intensity 241Am(Li) neutron sources. Scintillation-based fast-neutron detectors are a potentially superior technology to the existing AWCC and UNCL designs due to their spectroscopic capability and their inherently short neutron coincidence times that largely eliminate random coincidences and enable interrogation by stronger sources. One of the past impediments to the investigation and adoption of scintillation counters for the purpose of quantifying bulk uranium was the commercial availability of scintillators having the necessary neutron-gamma pulse-shape discrimination properties only as flammable liquids. Recently, Eljen EJ-299-34 PSD-plastic scintillator became commercially available. The present work is the first assessment of an array of PSD-plastic detectors for the purposes of quantifying bulk uranium. The detector panel used in the present work was originally built as the focal plane for a fast-neutron imager, but it was repurposed for the present investigation by construction of a stand to support the inner well of an AWCC immediately in front of the detector panel. The detector panel and data acquisition of this system are particularly well suited for performing active-well fast-neutron counting of LEU and HEU samples because the active detector volume is solid, the 241Am(Li) interrogating

  6. Doubles counting of highly multiplying items in reflective surroundings

    SciTech Connect (OSTI)

    Croft, Stephen; Evans, Louise G; Schear, Melissa A; Tobin, Stephen J

    2010-11-18

    When a neutrons are counted from a spontaneously fissile multiplying item in a reflecting environment the temporal behavior of the correlated signal following neutron birth is complex. At early times the signal is dominated by prompt fission events coming from spontaneous fission bursts and also from prompt fast-neutron induced fission events. At later times neutrons 'returning' from the surroundings induce fission and give rise to an additional chain of correlated events. The prompt and returning components probe the fissile and fertile constituents of the item in different ways and it is potentially beneficial to exploit this fact. In this work we look at how the two components can be represented using a linear combination of two simple functions. Fitting of the composite function to the capture time distribution represents one way of quantifying the proportion of each contribution. Another approach however is to use a dual shift register analysis where after each triggering event two coincidence gates are opened, one close to the trigger that responds preferentially to the prompt dynamics and one later in time which is more sensitive to the returning neutron induced events. To decide on the best gate positions and gate widths and also to estimate the counting precision we can use the analytical fit to work out the necessary gate utilization factors which are required in both these calculations. In this work, we develop the approach. Illustrative examples are given using spent Low Enriched Uranium (LEU) Pressurized light Water Reactor (LWR) fuel assemblies submersed in borated water and counted in a ring of {sup 3}He gas-filled proportional counters. In this case the prompt component is dominated by {sup 244}Cm spontaneous fission and induced fast neutron fission in for example {sup 238}U while the returning low energy neutrons induce fission mainly in the fissile nuclides such as {sup 239}Pu, {sup 241}Pu and {sup 235}U. One requirement is to calculate the Random

  7. Neutron multiplicity counting: Confidence intervals for reconstruction parameters

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Verbeke, Jerome M.

    2016-03-09

    From nuclear materials accountability to homeland security, the need for improved nuclear material detection, assay, and authentication has grown over the past decades. Starting in the 1940s, neutron multiplicity counting techniques have enabled quantitative evaluation of masses and multiplications of fissile materials. In this paper, we propose a new method to compute uncertainties on these parameters using a model-based sequential Bayesian processor, resulting in credible regions in the fissile material mass and multiplication space. These uncertainties will enable us to evaluate quantitatively proposed improvements to the theoretical fission chain model. Additionally, because the processor can calculate uncertainties in real time,more » it is a useful tool in applications such as portal monitoring: monitoring can stop as soon as a preset confidence of non-threat is reached.« less

  8. Status of in-plant neutron coincidence counting

    SciTech Connect (OSTI)

    Enssling, N.; Krick, M.; Menlove, H.; Stewart, J.

    1986-01-01

    Neutron coincidence counters are used in nuclear material processing plants to assay bulk quantities of plutonium or uranium. Passive assays of plutonium are often made with the High-Level Neutron Counter (HLNC or HLNC-II), the Dual-Range Coincidence Counter, or customized detector geometries. Active assays of uranium are often made with the Active Well Coincidence Counter or the Uranium Neutron Coincidence Collar. Modern counters may have flattened efficiency profiles, fast AMPTEK amplifier/discriminators mounted directly next to the /sup 3/He detection tubes, external background shields, or special sample-loading mechanisms. Typical counting times and accuracies that can be obtained for plutonium are summarized. If isotopic composition is known, large plutonium samples can be assayed in 100 to 200 s - comparable to the time requires to input sample data into the counter's calculator or computer.

  9. Working with SRNL - Our Facilities- Ultra Low-Level Underground Counting

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Facility Ultra Low-Level Underground Counting Facility Working with SRNL Our Facilities - Ultra Low-Level Underground Counting Facility The Ultra Low-Level Underground Counting Facility is the only facility of its kind in the country. This facility is located 50 feet below ground level, and has four-inch thick walls of pre-nuclear weapons era steel. This allows highly sensitive measurements of ultra-low amounts of environmental radioactivity, free from interference by background radiatio

  10. Cryogenic, high-resolution x-ray detector with high count rate capability

    DOE Patents [OSTI]

    Frank, Matthias; Mears, Carl A.; Labov, Simon E.; Hiller, Larry J.; Barfknecht, Andrew T.

    2003-03-04

    A cryogenic, high-resolution X-ray detector with high count rate capability has been invented. The new X-ray detector is based on superconducting tunnel junctions (STJs), and operates without thermal stabilization at or below 500 mK. The X-ray detector exhibits good resolution (.about.5-20 eV FWHM) for soft X-rays in the keV region, and is capable of counting at count rates of more than 20,000 counts per second (cps). Simple, FET-based charge amplifiers, current amplifiers, or conventional spectroscopy shaping amplifiers can provide the electronic readout of this X-ray detector.

  11. Modeling the Number of Ignitions Following an Earthquake: Developing Prediction Limits for Overdispersed Count Data

    Broader source: Energy.gov [DOE]

    Modeling the Number of Ignitions Following an Earthquake: Developing Prediction Limits for Overdispersed Count Data Elizabeth J. Kelly and Raymond N. Tell

  12. POST CLOSURE INSPECTION REPORT FOR CORRECTIVE ACTION UNIT 92: AREA 6 DECON PAD FACILITY, NEVADA TEST SITE NEVADA, FOR THE PERIOD JANUARY 2004 - DECEMBER 2004

    SciTech Connect (OSTI)

    BECHTEL NEVADA

    2005-03-01

    This Post-Closure Inspection Report provides an analysis and summary of inspections for Corrective Action Unit (CAU) 92, Area 6 Decon Pond Facility, Nevada Test Site, Nevada. CAU 92 was closed in accordance with the Resource Conservation and Recovery Act (RCRA) Part B Operational Permit (Nevada Division of Environmental Protection, 1995) and the Federal Facility Agreement and Consent Order of 1996 on May 11, 1999. CAU 92 consists of two Corrective Action Sites (CASs): CAS 06-04-01, Decon Pad oil/Water Separator; and CAS 06-05-02, Decontamination Pond (RCRA). Both CASs have use restrictions; however, only CAS 06-05-02, Decontamination Pond (RCRA), requires post-closure inspections. CAS 06-04-01, Decon Pad Oil/Water Separator, is located inside the fence at the Building 6-605 compound. This report covers the annual period January 2004 through December 2004.

  13. Evaluation of impact tests of solid steel billet onto concrete pads, and application to generic ISFSI storage cask for tipover and side drop

    SciTech Connect (OSTI)

    Witte, M.C.; Chen, T.F.; Murty, S.S.; Tang, D.T.; Mok, G.C.; Fischer, L.E.; Carlson, R.W.

    1997-05-01

    Twelve tests were performed at LLNL to assess loading conditions on a spent fuel casts for side drops, end drops and tipover events. The tests were performed with a 1/3-scale model concrete pad to benchmark the structural analysis code DYNA3D. The side drop and tipover test results are discussed in this report. The billet and test pad were modified with DYNA3D using material properties and techniques used in earlier tests. The peak or maximum deceleration test results were compared to the simulated analytical results. It was concluded that an analytical model based on DYNA3D code and has been adequately benchmarked for this type of application. A generic or represented cask was modified with the DYNA3D code and evaluated for ISFSI side drop and tipover events. The analytical method can be applied to similar casks to estimate impact loads on storage casks resulting from low-velocity side or tip impacts onto concrete storage pads.

  14. Engineering evaluation/cost analysis for the proposed removal of contaminated materials from pad 1 at the Elza Gate site, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Not Available

    1990-09-01

    This engineering evaluation/cost analysis (EE/CA) has been prepared in support of the proposed removal action for cleanup of radioactively contaminated concrete and soil beneath a building on privately owned commercial property in Oak Ridge, Tennessee. The property, known as the Elza Gate site, became contaminated with uranium-238, radium-226, thorium-232, thorium-230, and decay products as a result of the Manhattan Engineer District storing uranium ore and ore processing residues at the site in the early 1940s. The US Department of Energy (DOE) has responsibility for cleanup of the property under its Formerly Utilized Sites Remedial Action Program (FUSRAP). The DOE plans to remove the cracked and worn concrete pad and contaminated subsoil beneath the pad, after which the property owner/tenant will provide clean backfill and new concrete. Portions of the pad and subsoil are contaminated and, if stored or disposed of improperly, may represent a potential threat to public health or welfare and the environment. The EE/CA report is the appropriate documentation for the proposed removal action, as identified in guidance from the US Environmental Protection Agency. The objective of the EE/CA report, in addition to identifying the planned removal action, is to document the selection of response activities that will mitigate the potential for release of contaminants from the property into the environment and minimize the related threats to public health or welfare and the environment. 7 refs., 2 figs., 3 tabs.

  15. The IAEA neutron coincidence counting (INCC) and the DEMING least-squares fitting programs

    SciTech Connect (OSTI)

    Krick, M.S.; Harker, W.C.; Rinard, P.M.; Wenz, T.R.; Lewis, W.; Pham, P.; Ridder, P. de

    1998-12-01

    Two computer programs are described: (1) the INCC (IAEA or International Neutron Coincidence Counting) program and (2) the DEMING curve-fitting program. The INCC program is an IAEA version of the Los Alamos NCC (Neutron Coincidence Counting) code. The DEMING program is an upgrade of earlier Windows{reg_sign} and DOS codes with the same name. The versions described are INCC 3.00 and DEMING 1.11. The INCC and DEMING codes provide inspectors with the software support needed to perform calibration and verification measurements with all of the neutron coincidence counting systems used in IAEA inspections for the nondestructive assay of plutonium and uranium.

  16. The LANL C-NR counting room and fission product yields

    SciTech Connect (OSTI)

    Jackman, Kevin Richard

    2015-09-21

    This PowerPoint presentation focused on the following areas: LANL C-NR counting room; Fission product yields; Los Alamos Neutron wheel experiments; Recent experiments ad NCERC; and Post-detonation nuclear forensics

  17. Self-Calibrated Cluster Counts as a Probe of Primordial Non-Gaussianity

    SciTech Connect (OSTI)

    Oguri, Masamune; /KIPAC, Menlo Park

    2009-05-07

    We show that the ability to probe primordial non-Gaussianity with cluster counts is drastically improved by adding the excess variance of counts which contains information on the clustering. The conflicting dependences of changing the mass threshold and including primordial non-Gaussianity on the mass function and biasing indicate that the self-calibrated cluster counts well break the degeneracy between primordial non-Gaussianity and the observable-mass relation. Based on the Fisher matrix analysis, we show that the count variance improves constraints on f{sub NL} by more than an order of magnitude. It exhibits little degeneracy with dark energy equation of state. We forecast that upcoming Hyper Suprime-cam cluster surveys and Dark Energy Survey will constrain primordial non-Gaussianity at the level {sigma}(f{sub NL}) {approx} 8, which is competitive with forecasted constraints from next-generation cosmic microwave background experiments.

  18. U.S. oil production forecast update reflects lower rig count

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    U.S. oil production forecast update reflects lower rig count Lower oil prices and fewer rigs drilling for crude oil are expected to slow U.S. oil production growth this year and in ...

  19. Don't Count Your Ions Before They Dissociate | U.S. DOE Office...

    Office of Science (SC) Website

    Don't Count Your Ions Before They Dissociate Basic Energy Sciences (BES) BES Home About ... The green shading represents the 99.98% of the molecules that exist in a neutral, or ...

  20. Cosmic ray neutron background reduction using localized coincidence veto neutron counting

    DOE Patents [OSTI]

    Menlove, Howard O.; Bourret, Steven C.; Krick, Merlyn S.

    2002-01-01

    This invention relates to both the apparatus and method for increasing the sensitivity of measuring the amount of radioactive material in waste by reducing the interference caused by cosmic ray generated neutrons. The apparatus includes: (a) a plurality of neutron detectors, each of the detectors including means for generating a pulse in response to the detection of a neutron; and (b) means, coupled to each of the neutrons detectors, for counting only some of the pulses from each of the detectors, whether cosmic ray or fission generated. The means for counting includes a means that, after counting one of the pulses, vetos the counting of additional pulses for a prescribed period of time. The prescribed period of time is between 50 and 200 .mu.s. In the preferred embodiment the prescribed period of time is 128 .mu.s. The veto means can be an electronic circuit which includes a leading edge pulse generator which passes a pulse but blocks any subsequent pulse for a period of between 50 and 200 .mu.s. Alternately, the veto means is a software program which includes means for tagging each of the pulses from each of the detectors for both time and position, means for counting one of the pulses from a particular position, and means for rejecting those of the pulses which originate from the particular position and in a time interval on the order of the neutron die-away time in polyethylene or other shield material. The neutron detectors are grouped in pods, preferably at least 10. The apparatus also includes means for vetoing the counting of coincidence pulses from all of the detectors included in each of the pods which are adjacent to the pod which includes the detector which produced the pulse which was counted.

  1. Remaining Sites Verification Package for the 600-243 Petroleum-Contaminated Soil Bioremediation Pad, Waste Site Reclassification Form 2007-033

    SciTech Connect (OSTI)

    J. M. Capron

    2008-11-07

    The 600-243 waste site consisted of a bioremediation pad for petroleum-contaminated soils resulting from the 1100 Area Underground Storage Tank (UST) upgrades in 1994. In accordance with this evaluation, the verification sampling results support a reclassification of this site to Interim Closed Out. The results of verification sampling show that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also demonstrate that residual contaminant concentrations are protective of groundwater and the Columbia River.

  2. Class 1 Permit Modification Notification Addition of Structures within Technical Area 54, Area G, Pad 11, Dome 375 Los Alamos National Laboratory Hazardous Waste Facility Permit, July 2012

    SciTech Connect (OSTI)

    Vigil-Holterman, Luciana R.; Lechel, Robert A.

    2012-08-31

    The purpose of this letter is to notify the New Mexico Environment Department-Hazardous Waste Bureau (NMED-HWB) of a Class 1 Permit Modification to the Los Alamos National Laboratory (LANL) Hazardous Waste Facility Permit issued to the Department of Energy (DOE) and Los Alamos National Security, LLC (LANS) in November 2010. The modification adds structures to the container storage unit at Technical Area (TA) 54 Area G, Pad 11. Permit Section 3.1(3) requires that changes to the location of a structure that does not manage hazardous waste shall be changed within the Permit as a Class 1 modification without prior approval in accordance with Code of Federal Regulations, Title 40 (40 CFR), {section}270.42(a)(1). Structures have been added within Dome 375 located at TA-54, Area G, Pad 11 that will be used in support of waste management operations within Dome 375 and the modular panel containment structure located within Dome 375, but will not be used as waste management structures. The Class 1 Permit Modification revises Figure 36 in Attachment N, Figures; and Figure G.12-1 in Attachment G.12, Technical Area 54, Area G, Pad 11 Outdoor Container Storage Unit Closure Plan. Descriptions of the structures have also been added to Section A.4.2.9 in Attachment A, TA - Unit Descriptions; and Section 2.0 in Attachment G.12, Technical Area 54, Area G, Pad 11 Outdoor Container Storage Unit Closure Plan. Full description of the permit modification and the necessary changes are included in Enclosure 1. The modification has been prepared in accordance with 40 CFR {section}270.42(a)(l). This package includes this letter and an enclosure containing a description of the permit modification, text edits of the Permit sections, and the revised figures (collectively LA-UR-12-22808). Accordingly, a signed certification page is also enclosed. Three hard copies and one electronic copy of this submittal will be delivered to the NMED-HWB.

  3. FLOP Counts for "Small" Single-Node Miniapplication Tests

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    FLOP Counts for "Small" Single-Node Miniapplication Tests FLOP Counts for "Small" Single-Node Miniapplication Tests These data, obtained using the NERSC Hopper system, are provided for reference. Code MPI Tasks Threads Reference TFLOP Count Benchmark Time (seconds) # of iterations miniFE 144 1 5.05435E+12 130.2 (total program time) miniGhost 96 1 6.55500E+12 76.5 AMG 96 1 1.30418E+12 66.95 18 UMT 96 1 1.30211E+13 416.99 49 SNAP 96 1 5.84246E+11 15.37 3059 miniDFT 40 1

  4. Powered by NERSC, a Database of Billions of Genes and Counting!

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Powered by NERSC, a Database of Billions of Genes and Counting! Powered by NERSC, a Database of Billions of Genes and Counting! With More than a Billion Microbial genes, IMG/M Breaks a Record January 26, 2012 Linda Vu, lvu@lbl.gov, +1 510 495 2402 IMG/M team celebrates the recording of 1 billionth gene. Microbes are microscopic organisms that live in every nook and cranny of our planet. Without them, plants wouldn't grow, garbage wouldn't decay, humans wouldn't digest food, and there would

  5. Apparatus and method for temperature correction and expanded count rate of inorganic scintillation detectors

    DOE Patents [OSTI]

    Ianakiev, Kiril D.; Hsue, Sin Tao; Browne, Michael C.; Audia, Jeffrey M.

    2006-07-25

    The present invention includes an apparatus and corresponding method for temperature correction and count rate expansion of inorganic scintillation detectors. A temperature sensor is attached to an inorganic scintillation detector. The inorganic scintillation detector, due to interaction with incident radiation, creates light pulse signals. A photoreceiver processes the light pulse signals to current signals. Temperature correction circuitry that uses a fast light component signal, a slow light component signal, and the temperature signal from the temperature sensor to corrected an inorganic scintillation detector signal output and expanded the count rate.

  6. ULTRAVIOLET NUMBER COUNTS OF GALAXIES FROM SWIFT ULTRAVIOLET/OPTICAL TELESCOPE DEEP IMAGING OF THE CHANDRA DEEP FIELD SOUTH

    SciTech Connect (OSTI)

    Hoversten, E. A.; Gronwall, C.; Koch, T. S.; Roming, P. W. A.; Siegel, M. H.; Berk, D. E. Vanden; Breeveld, A. A.; Curran, P. A.; Still, M.

    2009-11-10

    Deep Swift UV/Optical Telescope (UVOT) imaging of the Chandra Deep Field South is used to measure galaxy number counts in three near-ultraviolet (NUV) filters (uvw2: 1928 A, uvm2: 2246 A, and uvw1: 2600 A) and the u band (3645 A). UVOT observations cover the break in the slope of the NUV number counts with greater precision than the number counts by the Hubble Space Telescope Space Telescope Imaging Spectrograph and the Galaxy Evolution Explorer, spanning a range 21 approx< m{sub AB} approx< 25. Model number counts confirm earlier investigations in favoring models with an evolving galaxy luminosity function.

  7. Calibration of the Accuscan II In Vivo System for Whole Body Counting

    SciTech Connect (OSTI)

    Orval R. Perry; David L. Georgeson

    2011-08-01

    This report describes the April 2011 calibration of the Accuscan II HpGe In Vivo system for whole body counting. The source used for the calibration was a NIST traceable BOMAB manufactured by DOE as INL2006 BOMAB containing Eu-154, Eu-155, Eu-152, Sb-125 and Y-88 with energies from 27 keV to 1836 keV with a reference date of 11/29/2006. The actual usable energy range was 86.5 keV to 1597 keV on 4/21/2011. The BOMAB was constructed inside the Accuscan II counting 'tub' in the order of legs, thighs, abdomen, thorax/arms, neck, and head. Each piece was taped to the backwall of the counter. The arms were taped to the thorax. The phantom was constructed between the v-ridges on the backwall of the Accuscan II counter. The energy and efficiency calibrations were performed using the INL2006 BOMAB. The calibrations were performed with the detectors in the scanning mode. This report includes an overview introduction and records for the energy/FWHM and efficiency calibration including performance verification and validation counting. The Accuscan II system was successfully calibrated for whole body counting and verified in accordance with ANSI/HPS N13.30-1996 criteria.

  8. Historical review of lung counting efficiencies for low energy photon emitters

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Jeffers, Karen L.; Hickman, David P.

    2014-03-01

    This publication reviews the measured efficiency and variability over time of a high purity planar germanium in vivo lung count system for multiple photon energies using increasingly thick overlays with the Lawrence Livermore Torso Phantom. Furthermore, the measured variations in efficiency are compared with the current requirement for in vivo bioassay performance as defined by the American National Standards Institute Standard.

  9. Corrective Action Decision Document/Closure Report for Corrective Action Unit 559: T Tunnel Compressor/Blower Pad, Nevada Test Site

    SciTech Connect (OSTI)

    NSTec Environmental Restoration

    2010-03-15

    This Corrective Action Decision Document (CADD)/Closure Report (CR) was prepared by the Defense Threat Reduction Agency (DTRA) for Corrective Action Unit (CAU) 559, T-Tunnel Compressor/Blower Pad. This CADD/CR is consistent with the requirements of the Federal Facility Agreement and Consent Order (FFACO) agreed to by the State of Nevada, the U.S. Department of Energy, and the U.S. Department of Defense. Corrective Action Unit 559 is comprised of one Corrective Action Site (CAS): • 12-25-13, Oil Stained Soil and Concrete The purpose of this CADD/CR is to provide justification and documentation supporting the recommendation for closure in place with use restrictions for CAU 559.

  10. A New Technique for Studying the Fano Factor And the Mean Energy Per Ion Pair in Counting Gases

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Panksky, A.; Breskin, A.; Chechik, R.

    1996-04-01

    A new method is presented for deriving the Fano factor and the mean energy per ion pair in the ultrasoft x-ray energy range. It is based on counting electrons deposited by a photon in a low-pressure gas, and is applicable for all counting gases. The energy dependence of these parameters for several hydrocarbons and gas mixtures is presented.

  11. Risk assessment of the retrieval of transuranic waste: Pads 1, 2, and 4, Technical Area-54, Area G, Los Alamos National Laboratory

    SciTech Connect (OSTI)

    Wilbert, K.A.; Lyon, B.F.; Hutchison, J.; Holmes, J.A.; Legg, J.L.; Simek, M.P.; Travis, C.C.; Wollert, D.A.

    1995-05-01

    The Risk Assessment for the Retrieval of Transuranic Waste is a comparative risk assessment of the potential adverse human health effects resulting from exposure to contaminants during retrieval and post-retrieval aboveground storage operations of post-1970 earthen-covered transuranic waste. Two alternatives are compared: (1) Immediate Retrieval and (2) Delayed Retrieval. Under the Immediate Retrieval Alternative, retrieval of the waste is assumed to begin immediately, Under the Delayed Retrieval Alternative, retrieval is delayed 10 years. The current risk assessment is on Pads 1, 2, and 4, at Technical Area-54, Area-G, Los Alamos National Laboratory (LANL). Risks are assessed independently for three scenarios: (1) incident-free retrieval operations, (2) incident-free storage operations, and (3) a drum failure analysis. The drum failure analysis evaluates container integrity under both alternatives and assesses the impacts of potential drum failures during retrieval operations. Risks associated with a series of drum failures are potentially severe for workers, off-site receptors, and general on-site employees if retrieval is delayed 10 years and administrative and engineering controls remain constant. Under the Delayed Retrieval Alternative, an average of 300 drums out of 16,647 are estimated to fail during retrieval operations due to general corrosion, while minimal drums are predicted to fail under the Immediate Retrieval Alternative. The results of the current study suggest that, based on risk, remediation of Pads 1, 2, and 4 at LANL should not be delayed. Although risks from incident-free operations in the Delayed Retrieval Alternative are low, risks due to corrosion and drum failures are potentially severe.

  12. Wedge sampling for computing clustering coefficients and triangle counts on large graphs

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Seshadhri, C.; Pinar, Ali; Kolda, Tamara G.

    2014-05-08

    Graphs are used to model interactions in a variety of contexts, and there is a growing need to quickly assess the structure of such graphs. Some of the most useful graph metrics are based on triangles, such as those measuring social cohesion. Despite the importance of these triadic measures, algorithms to compute them can be extremely expensive. We discuss the method of wedge sampling. This versatile technique allows for the fast and accurate approximation of various types of clustering coefficients and triangle counts. Furthermore, these techniques are extensible to counting directed triangles in digraphs. Our methods come with provable andmore » practical time-approximation tradeoffs for all computations. We provide extensive results that show our methods are orders of magnitude faster than the state of the art, while providing nearly the accuracy of full enumeration.« less

  13. $598,890 raised for northern New Mexico students, and counting...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    $598,890 raised Community Connections: Your link to news and opportunities from Los Alamos National Laboratory Latest Issue: September 1, 2016 all issues All Issues » submit $598,890 raised for northern New Mexico students, and counting... LAESF donations give scholars of all income levels access to higher education July 1, 2015 Celebrating a new record-breaking total for the Los Alamos Employees' Scholarship Fund are, from left, scholarship program chair Steven Girrens (Associate Director for

  14. Improving Neutron Measurement Capabilities; Expanding the Limits of Correlated Neutron Counting

    SciTech Connect (OSTI)

    Santi, Peter Angelo; Geist, William H.; Dougan, Arden

    2015-11-05

    A number of technical and practical limitations exist within the neutron correlated counting techniques used in safeguards, especially within the algorithms that are used to process and analyze the detected neutron signals. A multi-laboratory effort is underway to develop new and improved analysis and data processing algorithms based on fundamental physics principles to extract additional or more accurate information about nuclear material bearing items.

  15. Counts-in-Cylinders in the Sloan Digital Sky Survey with Comparisons to N-Body

    SciTech Connect (OSTI)

    Berrier, Heather D.; Barton, Elizabeth J.; Berrier, Joel C.; Bullock, James S.; Zentner, Andrew R.; Wechsler, Risa H. /KIPAC, Menlo Park /SLAC

    2010-12-16

    Environmental statistics provide a necessary means of comparing the properties of galaxies in different environments and a vital test of models of galaxy formation within the prevailing, hierarchical cosmological model. We explore counts-in-cylinders, a common statistic defined as the number of companions of a particular galaxy found within a given projected radius and redshift interval. Galaxy distributions with the same two-point correlation functions do not necessarily have the same companion count distributions. We use this statistic to examine the environments of galaxies in the Sloan Digital Sky Survey, Data Release 4. We also make preliminary comparisons to four models for the spatial distributions of galaxies, based on N-body simulations, and data from SDSS DR4 to study the utility of the counts-in-cylinders statistic. There is a very large scatter between the number of companions a galaxy has and the mass of its parent dark matter halo and the halo occupation, limiting the utility of this statistic for certain kinds of environmental studies. We also show that prevalent, empirical models of galaxy clustering that match observed two- and three-point clustering statistics well fail to reproduce some aspects of the observed distribution of counts-in-cylinders on 1, 3 and 6-h{sup -1}Mpc scales. All models that we explore underpredict the fraction of galaxies with few or no companions in 3 and 6-h{sup -1} Mpc cylinders. Roughly 7% of galaxies in the real universe are significantly more isolated within a 6 h{sup -1} Mpc cylinder than the galaxies in any of the models we use. Simple, phenomenological models that map galaxies to dark matter halos fail to reproduce high-order clustering statistics in low-density environments.

  16. Particle count monitoring of reverse osmosis water treatment for removal of low-level radionuclides

    SciTech Connect (OSTI)

    Moritz, E.J.; Hoffman, C.R.; Hergert, T.R.

    1995-03-01

    Laser diode particle counting technology and analytical measurements were used to evaluate a pilot-scale reverse osmosis (RO) water treatment system for removal of particulate matter and sub-picocurie low-level radionuclides. Stormwater mixed with Waste Water Treatment Plant (WWTP) effluent from the Rocky Flats Environmental Technology Site (RFETS), formerly a Department of Energy (DOE) nuclear weapons production facility, were treated. No chemical pretreatment of the water was utilized during this study. The treatment system was staged as follows: multimedia filtration, granular activated carbon adsorption, hollow tube ultrafiltration, and reverse osmosis membrane filtration. Various recovery rates and two RO membrane models were tested. Analytical measurements included total suspended solids (TSS), total dissolved solids (TDS), gross alpha ({alpha}) and gross beta ({beta}) activity, uranium isotopes {sup 233/234}U and {sup 238}U, plutonium {sup 239/240}Pu, and americium {sup 241}Am. Particle measurement between 1--150 microns ({mu}) included differential particle counts (DPC), and total particle counts (TPC) before and after treatment at various sampling points throughout the test. Performance testing showed this treatment system produced a high quality effluent in clarity and purity. Compared to raw water levels, TSS was reduced to below detection of 5 milligrams per liter (mg/L) and TDS reduced by 98%. Gross {alpha} was essentially removed 100%, and gross {beta} was reduced an average of 94%. Uranium activity was reduced by 99%. TPC between 1-150{mu} were reduced by an average 99.8% to less than 1,000 counts per milliliter (mL), similar in purity to a good drinking water treatment plant. Raw water levels of {sup 239/240}Pu and {sup 241}Am were below reliable quantitation limits and thus no removal efficiencies could be determined for these species.

  17. Cosmology Constraints from the Weak Lensing Peak Counts and the Power Spectrum in CFHTLenS

    SciTech Connect (OSTI)

    Liu, Jia; May, Morgan; Petri, Andrea; Haiman, Zoltan; Hui, Lam; Kratochvil, Jan M.

    2015-03-04

    Lensing peaks have been proposed as a useful statistic, containing cosmological information from non-Gaussianities that is inaccessible from traditional two-point statistics such as the power spectrum or two-point correlation functions. Here we examine constraints on cosmological parameters from weak lensing peak counts, using the publicly available data from the 154 deg2 CFHTLenS survey. We utilize a new suite of ray-tracing N-body simulations on a grid of 91 cosmological models, covering broad ranges of the three parameters Ωm, σ8, and w, and replicating the galaxy sky positions, redshifts, and shape noise in the CFHTLenS observations. We then build an emulator that interpolates the power spectrum and the peak counts to an accuracy of ≤ 5%, and compute the likelihood in the three-dimensional parameter space (Ωm, σ8, w) from both observables. We find that constraints from peak counts are comparable to those from the power spectrum, and somewhat tighter when different smoothing scales are combined. Neither observable can constrain w without external data. When the power spectrum and peak counts are combined, the area of the error “banana” in the (Ωm, σ8) plane reduces by a factor of ≈ two, compared to using the power spectrum alone. For a flat Λ cold dark matter model, combining both statistics, we obtain the constraint σ8m/0.27)0.63 = 0.85+0.03-0.03.

  18. Cosmology Constraints from the Weak Lensing Peak Counts and the Power Spectrum in CFHTLenS

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Liu, Jia; May, Morgan; Petri, Andrea; Haiman, Zoltan; Hui, Lam; Kratochvil, Jan M.

    2015-03-04

    Lensing peaks have been proposed as a useful statistic, containing cosmological information from non-Gaussianities that is inaccessible from traditional two-point statistics such as the power spectrum or two-point correlation functions. Here we examine constraints on cosmological parameters from weak lensing peak counts, using the publicly available data from the 154 deg2 CFHTLenS survey. We utilize a new suite of ray-tracing N-body simulations on a grid of 91 cosmological models, covering broad ranges of the three parameters Ωm, σ8, and w, and replicating the galaxy sky positions, redshifts, and shape noise in the CFHTLenS observations. We then build an emulator thatmore » interpolates the power spectrum and the peak counts to an accuracy of ≤ 5%, and compute the likelihood in the three-dimensional parameter space (Ωm, σ8, w) from both observables. We find that constraints from peak counts are comparable to those from the power spectrum, and somewhat tighter when different smoothing scales are combined. Neither observable can constrain w without external data. When the power spectrum and peak counts are combined, the area of the error “banana” in the (Ωm, σ8) plane reduces by a factor of ≈ two, compared to using the power spectrum alone. For a flat Λ cold dark matter model, combining both statistics, we obtain the constraint σ8(Ωm/0.27)0.63 = 0.85+0.03-0.03.« less

  19. Calibration of the Accuscan II In Vivo System for I-125 Thyroid Counting

    SciTech Connect (OSTI)

    Ovard R. Perry; David L. Georgeson

    2011-07-01

    This report describes the March 2011 calibration of the Accuscan II HpGe In Vivo system for I-125 thyroid counting. The source used for the calibration was a DOE manufactured Am-241/Eu-152 source contained in a 22 ml vial BEA Am-241/Eu-152 RMC II-1 with energies from 26 keV to 344 keV. The center of the detector housing was positioned 64 inches from the vault floor. This position places the approximate center line of the detector housing at the center line of the source in the phantom thyroid tube. The energy and efficiency calibration were performed using an RMC II phantom (Appendix J). Performance testing was conducted using source BEA Am-241/Eu-152 RMC II-1 and Validation testing was performed using an I-125 source in a 30 ml vial (I-125 BEA Thyroid 002) and an ANSI N44.3 phantom (Appendix I). This report includes an overview introduction and records for the energy/FWHM and efficiency calibration including performance verification and validation counting. The Accuscan II system was successfully calibrated for counting the thyroid for I-125 and verified in accordance with ANSI/HPS N13.30-1996 criteria.

  20. Calibration of the Accuscan II In Vivo System for I-131 Thyroid Counting

    SciTech Connect (OSTI)

    Orval R. Perry; David L. Georgeson

    2011-07-01

    This report describes the March 2011 calibration of the Accuscan II HpGe In Vivo system for I-131 thyroid counting. The source used for the calibration was an Analytics mixed gamma source 82834-121 distributed in an epoxy matrix in a Wheaton Liquid Scintillation Vial with energies from 88.0 keV to 1836.1 keV. The center of the detectors was position 64-feet from the vault floor. This position places the approximate center line of the detectors at the center line of the source in the thyroid tube. The calibration was performed using an RMC II phantom (Appendix J). Validation testing was performed using a Ba-133 source and an ANSI N44.3 Phantom (Appendix I). This report includes an overview introduction and records for the energy/FWHM and efficiency calibrations including verification counting. The Accuscan II system was successfully calibrated for counting the thyroid for I-131 and verified in accordance with ANSI/HPS N13.30-1996 criteria.

  1. The effect of deadtime and electronic transients on the predelay bias in neutron coincidence counting

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Croft, Stephen; Favalli, Andrea; Swinhoe, Martyn T.; Goddard, Braden; Stewart, Scott

    2016-01-13

    In neutron coincidence counting using the shift register autocorrelation technique, a predelay is inserted before the opening of the (R+A)-gate. Operationally the purpose of the predelay is to ensure that the (R+A)- and A-gates have matched effectiveness, otherwise a bias will result when the difference between the gates is used to calculate the accidentals corrected net reals coincidence rate. The necessity for the predelay was established experimentally in the early practical development and deployment of the coincidence counting method. The choice of predelay for a given detection system is usually made experimentally, but even today long standing traditional values (e.g.,more » 4.5 µs) are often used. This, at least in part, reflects the fact that a deep understanding of why a finite predelay setting is needed and how to control the underlying influences has not been fully worked out. We attempt, in this paper, to gain some insight into the problem. One aspect we consider is the slowing down, thermalization, and diffusion of neutrons in the detector moderator. The other is the influence of deadtime and electronic transients. These may be classified as non-ideal detector behaviors because they are not included in the conventional model used to interpret measurement data. From improved understanding of the effect of deadtime and electronic transients on the predelay bias in neutron coincidence counting, the performance of both future and current coincidence counters may be improved.« less

  2. Characterization of energy response for photon-counting detectors using x-ray fluorescence

    SciTech Connect (OSTI)

    Ding, Huanjun; Cho, Hyo-Min; Molloi, Sabee; Barber, William C.; Iwanczyk, Jan S.

    2014-12-15

    Purpose: To investigate the feasibility of characterizing a Si strip photon-counting detector using x-ray fluorescence. Methods: X-ray fluorescence was generated by using a pencil beam from a tungsten anode x-ray tube with 2 mm Al filtration. Spectra were acquired at 90 from the primary beam direction with an energy-resolved photon-counting detector based on an edge illuminated Si strip detector. The distances from the source to target and the target to detector were approximately 19 and 11 cm, respectively. Four different materials, containing silver (Ag), iodine (I), barium (Ba), and gadolinium (Gd), were placed in small plastic containers with a diameter of approximately 0.7 cm for x-ray fluorescence measurements. Linear regression analysis was performed to derive the gain and offset values for the correlation between the measured fluorescence peak center and the known fluorescence energies. The energy resolutions and charge-sharing fractions were also obtained from analytical fittings of the recorded fluorescence spectra. An analytical model, which employed four parameters that can be determined from the fluorescence calibration, was used to estimate the detector response function. Results: Strong fluorescence signals of all four target materials were recorded with the investigated geometry for the Si strip detector. The average gain and offset of all pixels for detector energy calibration were determined to be 6.95 mV/keV and ?66.33 mV, respectively. The detectors energy resolution remained at approximately 2.7 keV for low energies, and increased slightly at 45 keV. The average charge-sharing fraction was estimated to be 36% within the investigated energy range of 2045 keV. The simulated detector output based on the proposed response function agreed well with the experimental measurement. Conclusions: The performance of a spectral imaging system using energy-resolved photon-counting detectors is very dependent on the energy calibration of the detector. The

  3. The number counts and infrared backgrounds from infrared-bright galaxies

    SciTech Connect (OSTI)

    Hacking, P.B.; Soifer, B.T. California Institute of Technology, Pasadena )

    1991-02-01

    Extragalactic number counts and diffuse backgrounds at 25, 60, and 100 microns are predicted using new luminosity functions and improved spectral-energy distribution density functions derived from IRAS observations of nearby galaxies. Galaxies at redshifts z less than 3 that are like those in the local universe should produce a minimum diffuse background of 0.0085, 0.038, and 0.13 MJy/sr at 25, 60, and 100 microns, respectively. Models with significant luminosity evolution predict backgrounds about a factor of 4 greater than this minimum. 22 refs.

  4. Laboratory adds a sixth R&D 100 award to its 2009 count

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    R&D 100 awards Laboratory adds a sixth R&D 100 award to its 2009 count This year's awards bring the Los Alamos total to 113 since the Laboratory first entered the competition in 1978. November 4, 2009 Los Alamos National Laboratory sits on top of a once-remote mesa in northern New Mexico with the Jemez mountains as a backdrop to research and innovation covering multi-disciplines from bioscience, sustainable energy sources, to plasma physics and new materials. Los Alamos National

  5. Longitudinal Bunch Pattern Measurements through Single Photon Counting at SPEAR3

    SciTech Connect (OSTI)

    Wang, Hongyi; /UC, San Diego

    2012-09-07

    The Stanford Synchrotron Radiation Lightsource (SSRL), a division of SLAC National Accelerator Laboratory, is a synchrotron light source that provides x-rays for experimental use. As electrons are bent in the storage ring, they emit electromagnetic radiation. There are 372 different buckets which electrons can be loaded into. Different filling patterns produce different types of x-rays. What is the bunch pattern at a given time? Which filling pattern is better? Are there any flaws to the current injection system? These questions can be answered with this single photon counting experiment.

  6. Sequential data assimilation for single-molecule FRET photon-counting data

    SciTech Connect (OSTI)

    Matsunaga, Yasuhiro; Kidera, Akinori; Sugita, Yuji

    2015-06-07

    Data assimilation is a statistical method designed to improve the quality of numerical simulations in combination with real observations. Here, we develop a sequential data assimilation method that incorporates one-dimensional time-series data of smFRET (single-molecule Frster resonance energy transfer) photon-counting into conformational ensembles of biomolecules derived from replicated molecular dynamics (MD) simulations. A particle filter using a large number of replicated MD simulations with a likelihood function for smFRET photon-counting data is employed to screen the conformational ensembles that match the experimental data. We examine the performance of the method using emulated smFRET data and coarse-grained (CG) MD simulations of a dye-labeled polyproline-20. The method estimates the dynamics of the end-to-end distance from smFRET data as well as revealing that of latent conformational variables. The particle filter is also able to correct model parameter dependence in CG MD simulations. We discuss the applicability of the method to real experimental data for conformational dynamics of biomolecules.

  7. Liquid scintillation counting methodology for 99Tc analysis. A remedy for radiopharmaceutical waste

    SciTech Connect (OSTI)

    Khan, Mumtaz; Um, Wooyong

    2015-08-13

    This paper presents a new approach for liquid scintillation counting (LSC) analysis of single-radionuclide samples containing appreciable organic or inorganic quench. This work offers better analytical results than existing LSC methods for technetium-99 (99gTc) analysis with significant savings in analysis cost and time. The method was developed to quantify 99gTc in environmental liquid and urine samples using LSC. Method efficiency was measured in the presence of 1.9 to 11,900 ppm total dissolved solids. The quench curve was proved to be effective in the case of spiked 99gTc activity calculation for deionized water, tap water, groundwater, seawater, and urine samples. Counting efficiency was found to be 91.66% for Ultima Gold LLT (ULG-LLT) and Ultima Gold (ULG). Relative error in spiked 99gTc samples was ±3.98% in ULG and ULG-LLT cocktails. Minimum detectable activity was determined to be 25.3 mBq and 22.7 mBq for ULG-LLT and ULG cocktails, respectively. A pre-concentration factor of 1000 was achieved at 100°C for 100% chemical recovery.

  8. Association Between White Blood Cell Count Following Radiation Therapy With Radiation Pneumonitis in Non-Small Cell Lung Cancer

    SciTech Connect (OSTI)

    Tang, Chad; Gomez, Daniel R. [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Wang, Hongmei [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Department of Radiation Oncology, Nanfang Hospital, Southern Medical University, Guangzhou (China); Levy, Lawrence B. [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Zhuang, Yan [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Xu, Ting; Nguyen, Quynh; Komaki, Ritsuko [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Liao, Zhongxing, E-mail: zliao@mdanderson.org [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States)

    2014-02-01

    Purpose: Radiation pneumonitis (RP) is an inflammatory response to radiation therapy (RT). We assessed the association between RP and white blood cell (WBC) count, an established metric of systemic inflammation, after RT for non-small cell lung cancer. Methods and Materials: We retrospectively analyzed 366 patients with non-small cell lung cancer who received ?60 Gy as definitive therapy. The primary endpoint was whether WBC count after RT (defined as 2 weeks through 3 months after RT completion) was associated with grade ?3 or grade ?2 RP. Median lung volume receiving ?20 Gy (V{sub 20}) was 31%, and post-RT WBC counts ranged from 1.7 to 21.2 10{sup 3} WBCs/?L. Odds ratios (ORs) associating clinical variables and post-RT WBC counts with RP were calculated via logistic regression. A recursive-partitioning algorithm was used to define optimal post-RT WBC count cut points. Results: Post-RT WBC counts were significantly higher in patients with grade ?3 RP than without (P<.05). Optimal cut points for post-RT WBC count were found to be 7.4 and 8.0 10{sup 3}/?L for grade ?3 and ?2 RP, respectively. Univariate analysis revealed significant associations between post-RT WBC count and grade ?3 (n=46, OR=2.6, 95% confidence interval [CI] 1.4?4.9, P=.003) and grade ?2 RP (n=164, OR=2.0, 95% CI 1.2?3.4, P=.01). This association held in a stepwise multivariate regression. Of note, V{sub 20} was found to be significantly associated with grade ?2 RP (OR=2.2, 95% CI 1.2?3.4, P=.01) and trended toward significance for grade ?3 RP (OR=1.9, 95% CI 1.0-3.5, P=.06). Conclusions: Post-RT WBC counts were significantly and independently associated with RP and have potential utility as a diagnostic or predictive marker for this toxicity.

  9. Analysis of 161Tb by radiochemical separation and liquid scintillation counting

    SciTech Connect (OSTI)

    Jiang, J.; Davies, A.; Arrigo, L.; Friese, J.; Seiner, B. N.; Greenwood, L.; Finch, Z.

    2015-12-05

    The determination of 161Tb activity is problematic due to its very low fission yield, short half-life, and the complication of its gamma spectrum. At AWE, radiochemically purified 161Tb solution was measured on a PerkinElmer 1220 QuantulusTM Liquid Scintillation Spectrometer. Since there was no 161Tb certified standard solution available commercially, the counting efficiency was determined by the CIEMAT/NIST Efficiency Tracing method. The method was validated during a recent inter-laboratory comparison exercise involving the analysis of a uranium sample irradiated with thermal neutrons. Lastly, the measured 161Tb result was in excellent agreement with the result using gamma spectrometry and the result obtained by Pacific Northwest National Laboratory.

  10. Analysis of 161Tb by radiochemical separation and liquid scintillation counting

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Jiang, J.; Davies, A.; Arrigo, L.; Friese, J.; Seiner, B. N.; Greenwood, L.; Finch, Z.

    2015-12-05

    The determination of 161Tb activity is problematic due to its very low fission yield, short half-life, and the complication of its gamma spectrum. At AWE, radiochemically purified 161Tb solution was measured on a PerkinElmer 1220 QuantulusTM Liquid Scintillation Spectrometer. Since there was no 161Tb certified standard solution available commercially, the counting efficiency was determined by the CIEMAT/NIST Efficiency Tracing method. The method was validated during a recent inter-laboratory comparison exercise involving the analysis of a uranium sample irradiated with thermal neutrons. Lastly, the measured 161Tb result was in excellent agreement with the result using gamma spectrometry and the result obtainedmore » by Pacific Northwest National Laboratory.« less

  11. Full counting statistics of energy fluctuations in a driven quantum resonator

    SciTech Connect (OSTI)

    Clerk, A. A.

    2011-10-15

    We consider the statistics of time-integrated energy fluctuations of a driven bosonic single-mode resonator, as measured by a quantum nondemolition (QND) detector, using the standard Keldysh prescription to define higher moments. We find that, due to an effective cascading of fluctuations, these statistics are surprisingly nonclassical: the low-temperature, quantum probability distribution is not equivalent to the high-temperature classical distribution evaluated at some effective temperature. Moreover, for a sufficiently large drive detuning and low temperatures, the Keldysh-ordered quasiprobability distribution characterizing these fluctuations fails to be positive-definite; this is similar to the full counting statistics of charge in superconducting systems. We argue that this indicates a kind of nonclassical behavior akin to that tested by Leggett-Garg inequalities.

  12. On the single-photon-counting (SPC) modes of imaging using an XFEL source

    SciTech Connect (OSTI)

    Wang, Zhehui

    2015-12-14

    In this study, the requirements to achieve high detection efficiency (above 50%) and gigahertz (GHz) frame rate for the proposed 42-keV X-ray free-electron laser (XFEL) at Los Alamos are summarized. Direct detection scenarios using C (diamond), Si, Ge and GaAs semiconductor sensors are analyzed. Single-photon counting (SPC) mode and weak SPC mode using Si can potentially meet the efficiency and frame rate requirements and be useful to both photoelectric absorption and Compton physics as the photon energy increases. Multilayer three-dimensional (3D) detector architecture, as a possible means to realize SPC modes, is compared with the widely used two-dimensional (2D) hybrid planar electrode structure and 3D deeply entrenched electrode architecture. Demonstration of thin film cameras less than 100-μm thick with onboard thin ASICs could be an initial step to realize multilayer 3D detectors and SPC modes for XFELs.

  13. Measurement of uranium and plutonium in solid waste by passive photon or neutron counting and isotopic neutron source interrogation

    SciTech Connect (OSTI)

    Crane, T.W.

    1980-03-01

    A summary of the status and applicability of nondestructive assay (NDA) techniques for the measurement of uranium and plutonium in 55-gal barrels of solid waste is reported. The NDA techniques reviewed include passive gamma-ray and x-ray counting with scintillator, solid state, and proportional gas photon detectors, passive neutron counting, and active neutron interrogation with neutron and gamma-ray counting. The active neutron interrogation methods are limited to those employing isotopic neutron sources. Three generic neutron sources (alpha-n, photoneutron, and /sup 252/Cf) are considered. The neutron detectors reviewed for both prompt and delayed fission neutron detection with the above sources include thermal (/sup 3/He, /sup 10/BF/sub 3/) and recoil (/sup 4/He, CH/sub 4/) proportional gas detectors and liquid and plastic scintillator detectors. The instrument found to be best suited for low-level measurements (< 10 nCi/g) is the /sup 252/Cf Shuffler. The measurement technique consists of passive neutron counting followed by cyclic activation using a /sup 252/Cf source and delayed neutron counting with the source withdrawn. It is recommended that a waste assay station composed of a /sup 252/Cf Shuffler, a gamma-ray scanner, and a screening station be tested and evaluated at a nuclear waste site. 34 figures, 15 tables.

  14. Task-based weights for photon counting spectral x-ray imaging

    SciTech Connect (OSTI)

    Bornefalk, Hans

    2011-11-15

    Purpose: To develop a framework for taking the spatial frequency composition of an imaging task into account when determining optimal bin weight factors for photon counting energy sensitive x-ray systems. A second purpose of the investigation is to evaluate the possible improvement compared to using pixel based weights. Methods: The Fourier based approach of imaging performance and detectability index d' is applied to pulse height discriminating photon counting systems. The dependency of d' on the bin weight factors is made explicit, taking into account both differences in signal and noise transfer characteristics across bins and the spatial frequency dependency of interbin correlations from reabsorbed scatter. Using a simplified model of a specific silicon detector, d' values for a high and a low frequency imaging task are determined for optimal weights and compared to pixel based weights. Results: The method successfully identifies bins where a large point spread function degrades detection of high spatial frequency targets. The method is also successful in determining how to downweigh highly correlated bins. Quantitative predictions for the simplified silicon detector model indicate that improvements in the detectability index when applying task-based weights instead of pixel based weights are small for high frequency targets, but could be in excess of 10% for low frequency tasks where scatter-induced correlation otherwise degrade detectability. Conclusions: The proposed method makes the spatial frequency dependency of complex correlation structures between bins and their effect on the system detective quantum efficiency easier to analyze and allows optimizing bin weights for given imaging tasks. A potential increase in detectability of double digit percents in silicon detector systems operated at typical CT energies (100 kVp) merits further evaluation on a real system. The method is noted to be of higher relevance for silicon detectors than for cadmium (zink

  15. Hydrogen cluster/network in tobermorite as studied by multiple-quantum spin counting {sup 1}H NMR

    SciTech Connect (OSTI)

    Mogami, Yuuki; Yamazaki, Satoru; Matsuno, Shinya; Matsui, Kunio; Noda, Yasuto; Takegoshi, K.

    2014-12-15

    Proton multiple-quantum (MQ) spin-counting experiment has been employed to study arrangement of hydrogen atoms in 9 Å/11 Å natural/synthetic tobermorites. Even though all tobermorite samples give similar characterless, broad static-powder {sup 1}H NMR spectra, their MQ spin-counting spectra are markedly different; higher quanta in 11 Å tobermorite do not grow with the MQ excitation time, while those in 9 Å one do. A statistical analysis of the MQ results recently proposed [26] is applied to show that hydrogens align in 9 Å tobermorite one dimensionally, while in 11 Å tobermorite they exist as a cluster of 5–8 hydrogen atoms.

  16. 500-MHz x-ray counting with a Si-APD and a fast-pulse processing system

    SciTech Connect (OSTI)

    Kishimoto, Shunji; Taniguchi, Takashi; Tanaka, Manobu

    2010-06-23

    We introduce a counting system of up to 500 MHz for synchrotron x-ray high-rate measurements. A silicon avalanche photodiode detector was used in the counting system. The fast-pulse circuit of the amplifier was designed with hybrid ICs to prepare an ASIC system for a large-scale pixel array detector in near future. The fast amplifier consists of two cascading emitter-followers using 10-GHz band transistors. A count-rate of 3.25x10{sup 8} s{sup -1} was then achieved using the system for 8-keV x-rays. However, a baseline shift by adopting AC-coupling in the amplifier disturbed us to observe the maximum count of 4.49x10{sup 8} s{sup -1}, determined by electron-bunch filling into a ring accelerator. We also report that an amplifier with a baseline restorer was tested in order to keep the baseline level to be 0 V even at high input rates.

  17. Degree of polarization and source counts of faint radio sources from Stacking Polarized intensity

    SciTech Connect (OSTI)

    Stil, J. M.; George, S. J.; Keller, B. W.; Taylor, A. R.

    2014-06-01

    We present stacking polarized intensity as a means to study the polarization of sources that are too faint to be detected individually in surveys of polarized radio sources. Stacking offers not only high sensitivity to the median signal of a class of radio sources, but also avoids a detection threshold in polarized intensity, and therefore an arbitrary exclusion of sources with a low percentage of polarization. Correction for polarization bias is done through a Monte Carlo analysis and tested on a simulated survey. We show that the nonlinear relation between the real polarized signal and the detected signal requires knowledge of the shape of the distribution of fractional polarization, which we constrain using the ratio of the upper quartile to the lower quartile of the distribution of stacked polarized intensities. Stacking polarized intensity for NRAO VLA Sky Survey (NVSS) sources down to the detection limit in Stokes I, we find a gradual increase in median fractional polarization that is consistent with a trend that was noticed before for bright NVSS sources, but is much more gradual than found by previous deep surveys of radio polarization. Consequently, the polarized radio source counts derived from our stacking experiment predict fewer polarized radio sources for future surveys with the Square Kilometre Array and its pathfinders.

  18. Risk communication with Fukushima residents affected by the Fukushima Daiichi accident at whole-body counting

    SciTech Connect (OSTI)

    Gunji, I.; Furuno, A.; Yonezawa, R.; Sugiyama, K.

    2013-07-01

    After the Tokyo Electric Power Company (TEPCO) Fukushima Daiichi nuclear power plant accident, the Tokai Research and Development Center of the Japan Atomic Energy Agency (JAEA) have had direct dialogue as risk communication with Fukushima residents who underwent whole-body counting examination (WBC). The purpose of the risk communication was to exchange information and opinions about radiation in order to mitigate Fukushima residents' anxiety and stress. Two kinds of opinion surveys were performed: one survey evaluated residents' views of the nuclear accident itself and the second survey evaluated the management of WBC examination as well as the quality of JAEA's communication skills on risks. It appears that most Fukushima residents seem to have reduced their anxiety level after the direct dialogue. The results of the surveys show that Fukushima residents have the deepest anxiety and concern about their long-term health issues and that they harbor anger toward the government and TEPCO. On the other hand, many WBC patients and patients' relatives have expressed gratitude for help in reducing their feelings of anxiety.

  19. On the single-photon-counting (SPC) modes of imaging using an XFEL source

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Wang, Zhehui

    2015-12-14

    In this study, the requirements to achieve high detection efficiency (above 50%) and gigahertz (GHz) frame rate for the proposed 42-keV X-ray free-electron laser (XFEL) at Los Alamos are summarized. Direct detection scenarios using C (diamond), Si, Ge and GaAs semiconductor sensors are analyzed. Single-photon counting (SPC) mode and weak SPC mode using Si can potentially meet the efficiency and frame rate requirements and be useful to both photoelectric absorption and Compton physics as the photon energy increases. Multilayer three-dimensional (3D) detector architecture, as a possible means to realize SPC modes, is compared with the widely used two-dimensional (2D) hybridmore » planar electrode structure and 3D deeply entrenched electrode architecture. Demonstration of thin film cameras less than 100-μm thick with onboard thin ASICs could be an initial step to realize multilayer 3D detectors and SPC modes for XFELs.« less

  20. Implementation and Initial Testing of Advanced Processing and Analysis Algorithms for Correlated Neutron Counting

    SciTech Connect (OSTI)

    Santi, Peter Angelo; Cutler, Theresa Elizabeth; Favalli, Andrea; Koehler, Katrina Elizabeth; Henzl, Vladimir; Henzlova, Daniela; Parker, Robert Francis; Croft, Stephen

    2015-12-01

    In order to improve the accuracy and capabilities of neutron multiplicity counting, additional quantifiable information is needed in order to address the assumptions that are present in the point model. Extracting and utilizing higher order moments (Quads and Pents) from the neutron pulse train represents the most direct way of extracting additional information from the measurement data to allow for an improved determination of the physical properties of the item of interest. The extraction of higher order moments from a neutron pulse train required the development of advanced dead time correction algorithms which could correct for dead time effects in all of the measurement moments in a self-consistent manner. In addition, advanced analysis algorithms have been developed to address specific assumptions that are made within the current analysis model, namely that all neutrons are created at a single point within the item of interest, and that all neutrons that are produced within an item are created with the same energy distribution. This report will discuss the current status of implementation and initial testing of the advanced dead time correction and analysis algorithms that have been developed in an attempt to utilize higher order moments to improve the capabilities of correlated neutron measurement techniques.

  1. SEDS: THE SPITZER EXTENDED DEEP SURVEY. SURVEY DESIGN, PHOTOMETRY, AND DEEP IRAC SOURCE COUNTS

    SciTech Connect (OSTI)

    Ashby, M. L. N.; Willner, S. P.; Fazio, G. G.; Huang, J.-S.; Hernquist, L.; Hora, J. L.; Arendt, R.; Barmby, P.; Barro, G.; Faber, S.; Guhathakurta, P.; Bouwens, R.; Cattaneo, A.; Croton, D.; Dave, R.; Dunlop, J. S.; Egami, E.; Finlator, K.; Grogin, N. A.; and others

    2013-05-20

    The Spitzer Extended Deep Survey (SEDS) is a very deep infrared survey within five well-known extragalactic science fields: the UKIDSS Ultra-Deep Survey, the Extended Chandra Deep Field South, COSMOS, the Hubble Deep Field North, and the Extended Groth Strip. SEDS covers a total area of 1.46 deg{sup 2} to a depth of 26 AB mag (3{sigma}) in both of the warm Infrared Array Camera (IRAC) bands at 3.6 and 4.5 {mu}m. Because of its uniform depth of coverage in so many widely-separated fields, SEDS is subject to roughly 25% smaller errors due to cosmic variance than a single-field survey of the same size. SEDS was designed to detect and characterize galaxies from intermediate to high redshifts (z = 2-7) with a built-in means of assessing the impact of cosmic variance on the individual fields. Because the full SEDS depth was accumulated in at least three separate visits to each field, typically with six-month intervals between visits, SEDS also furnishes an opportunity to assess the infrared variability of faint objects. This paper describes the SEDS survey design, processing, and publicly-available data products. Deep IRAC counts for the more than 300,000 galaxies detected by SEDS are consistent with models based on known galaxy populations. Discrete IRAC sources contribute 5.6 {+-} 1.0 and 4.4 {+-} 0.8 nW m{sup -2} sr{sup -1} at 3.6 and 4.5 {mu}m to the diffuse cosmic infrared background (CIB). IRAC sources cannot contribute more than half of the total CIB flux estimated from DIRBE data. Barring an unexpected error in the DIRBE flux estimates, half the CIB flux must therefore come from a diffuse component.

  2. Recent Developments In Fast Neutron Detection And Multiplicity Counting With Verification With Liquid Scintillator

    SciTech Connect (OSTI)

    Nakae, L; Chapline, G; Glenn, A; Kerr, P; Kim, K; Ouedraogo, S; Prasad, M; Sheets, S; Snyderman, N; Verbeke, J; Wurtz, R

    2011-09-30

    For many years at LLNL, we have been developing time-correlated neutron detection techniques and algorithms for applications such as Arms Control, Threat Detection and Nuclear Material Assay. Many of our techniques have been developed specifically for the relatively low efficiency (a few percent) attainable by detector systems limited to man-portability. Historically, we used thermal neutron detectors (mainly {sup 3}He), taking advantage of the high thermal neutron interaction cross-sections. More recently, we have been investigating the use of fast neutron detection with liquid scintillators, inorganic crystals, and in the near future, pulse-shape discriminating plastics which respond over 1000 times faster (nanoseconds versus tens of microseconds) than thermal neutron detectors. Fast neutron detection offers considerable advantages, since the inherent nanosecond production time-scales of spontaneous fission and neutron-induced fission are preserved and measured instead of being lost by thermalization required for thermal neutron detectors. We are now applying fast neutron technology to the safeguards regime in the form of fast portable digital electronics as well as faster and less hazardous scintillator formulations. Faster detector response times and sensitivity to neutron momentum show promise for measuring, differentiating, and assaying samples that have modest to very high count rates, as well as mixed fission sources like Cm and Pu. We report on measured results with our existing liquid scintillator array, and progress on the design of a nuclear material assay system that incorporates fast neutron detection, including the surprising result that fast liquid scintillator detectors become competitive and even surpass the precision of {sup 3}He-based counters measuring correlated pairs in modest (kg) samples of plutonium.

  3. Separation and counting of single molecules through nanofluidics, programmable electrophoresis, and nanoelectrode-gated tunneling and dielectric detection

    DOE Patents [OSTI]

    Lee, James W.; Thundat, Thomas G.

    2006-04-25

    An apparatus for carrying out the separation, detection, and/or counting of single molecules at nanometer scale. Molecular separation is achieved by driving single molecules through a microfluidic or nanofluidic medium using programmable and coordinated electric fields. In various embodiments, the fluidic medium is a strip of hydrophilic material on nonconductive hydrophobic surface, a trough produced by parallel strips of hydrophobic nonconductive material on a hydrophilic base, or a covered passageway produced by parallel strips of hydrophobic nonconductive material on a hydrophilic base together with a nonconductive cover on the parallel strips of hydrophobic nonconductive material. The molecules are detected and counted using nanoelectrode-gated electron tunneling methods, dielectric monitoring, and other methods.

  4. Impact of sensitivity and throughput on optimum selection of a low-background alpha/beta gross counting system

    SciTech Connect (OSTI)

    Seymour, R.; Sergent, F.; Knight, K.; Kyker, B.

    1992-12-31

    Selection of the appropriate low-background counting system is determined by the laboratory`s measurement requirements including the radionuclide activities being measured, required sensitivity, sample volume, sample throughput, operator skill, automation, reporting requirements, budget, reliability, service, and upgrade capability. These requirements are ranked differently by each user. Nevertheless, any selection requires that the sensitivity and sample throughput be evaluated first because these parameters are instrument-specific, cannot be changed after the equipment is purchased and are easily quantified beforehand. Many of the other criteria are also related to sensitivity and affect the choice of instrument. Mathematical expressions, useful in evaluating sensitivity and throughput, are reviewed, extended, and applied to selecting a low-background alpha/beta counting system.

  5. SU-E-I-77: A Noise Reduction Technique for Energy-Resolved Photon-Counting Detectors

    SciTech Connect (OSTI)

    Lam Ng, A; Ding, H; Cho, H; Molloi, S

    2014-06-01

    Purpose: Finding the optimal energy threshold setting for an energy-resolved photon-counting detector has an important impact on the maximization of contrast-to-noise-ratio (CNR). We introduce a noise reduction method to enhance CNR by reducing the noise in each energy bin without altering the average gray levels in the projection and image domains. Methods: We simulated a four bin energy-resolved photon-counting detector based on Si with a 10 mm depth of interaction. TASMIP algorithm was used to simulate a spectrum of 65 kVp with 2.7 mm Al filter. A 13 mm PMMA phantom with hydroxyapatite and iodine at different concentrations (100, 200 and 300 mg/ml for HA, and 2, 4, and 8 mg/ml for Iodine) was used. Projection-based and Image-based energy weighting methods were used to generate weighted images. A reference low noise image was used for noise reduction purposes. A Gaussian-like weighting function which computes the similarity between pixels of interest was calculated from the reference image and implemented on a pixel by pixel basis for the noisy images. Results: CNR improvement compared to different methods (Charge-Integrated, Photon-Counting and Energy-Weighting) and after noise reduction was highly task-dependent. The CNR improvement with respect to the Charge-Integrated CNR for hydroxyapatite and iodine were 1.8 and 1.5, respectively. In each of the energy bins, the noise was reduced by approximately factor of two without altering their respective average gray levels. Conclusion: The proposed noise reduction technique for energy-resolved photon-counting detectors can significantly reduce image noise. This technique can be used as a compliment to the current energy-weighting methods in CNR optimization.

  6. MEASUREMENT OF RADIONUCLIDES USING ION CHROMATOGRAPHY AND FLOW-CELL SCINTILLATION COUNTING WITH PULSE SHAPE DISCRIMINATION

    SciTech Connect (OSTI)

    R. A. Fjeld; T.A. DeVol; J.D. Leyba

    2000-03-30

    Radiological characterization and monitoring is an important component of environmental management activities throughout the Department of Energy complex. Gamma-ray spectroscopy is the technology most often used for the detection of radionuclides. However, radionuclides which cannot easily be detected by gamma-ray spectroscopy, such as pure beta emitters and transuranics, pose special problems because their quantification generally requires labor intensive radiochemical separations procedures that are time consuming and impractical for field applications. This project focused on a technology for measuring transuranics and pure beta emitters relatively quickly and has the potential of being field deployable. The technology combines ion exchange liquid chromatography and on-line alpha/beta pulse shape discriminating scintillation counting to produce simultaneous alpha and beta chromatograms. The basic instrumentation upon which the project was based was purchased in the early 1990's. In its original commercial form, the instrumentation was capable of separating select activation/fission products in ionic forms from relatively pure aqueous samples. We subsequently developed the capability of separating and detecting actinides (thorium, uranium, neptunium, plutonium, americium, and curium) in less than 30 minutes (Reboul, 1993) and realized that the potential time savings over traditional radiochemical methods for isolating some of these radionuclides was significant. However, at that time, the technique had only been used for radionuclide concentrations that were considerably above environmental levels and for aqueous samples of relatively high chemical purity. For the technique to be useful in environmental applications, development work was needed in lowering detection limits; to be useful in applications involving non-aqueous matrices such as soils and sludges or complex aqueous matrices such as those encountered in waste samples, development work was needed in

  7. High quantum efficiency and low dark count rate in multi-layer superconducting nanowire single-photon detectors

    SciTech Connect (OSTI)

    Jafari Salim, A. Eftekharian, A.; Hamed Majedi, A.

    2014-02-07

    In this paper, we theoretically show that a multi-layer superconducting nanowire single-photon detector (SNSPD) is capable of approaching characteristics of an ideal SNSPD in terms of the quantum efficiency, dark count, and band-width. A multi-layer structure improves the performance in two ways. First, the potential barrier for thermally activated vortex crossing, which is the major source of dark counts and the reduction of the critical current in SNSPDs is elevated. In a multi-layer SNSPD, a vortex is made of 2D-pancake vortices that form a stack. It will be shown that the stack of pancake vortices effectively experiences a larger potential barrier compared to a vortex in a single-layer SNSPD. This leads to an increase in the experimental critical current as well as significant decrease in the dark count rate. In consequence, an increase in the quantum efficiency for photons of the same energy or an increase in the sensitivity to photons of lower energy is achieved. Second, a multi-layer structure improves the efficiency of single-photon absorption by increasing the effective optical thickness without compromising the single-photon sensitivity.

  8. Comparison of MCNP6 and experimental results for neutron counts, Rossi-{alpha}, and Feynman-{alpha} distributions

    SciTech Connect (OSTI)

    Talamo, A.; Gohar, Y.; Sadovich, S.; Kiyavitskaya, H.; Bournos, V.; Fokov, Y.; Routkovskaya, C.

    2013-07-01

    MCNP6, the general-purpose Monte Carlo N-Particle code, has the capability to perform time-dependent calculations by tracking the time interval between successive events of the neutron random walk. In fixed-source calculations for a subcritical assembly, the zero time value is assigned at the moment the neutron is emitted by the external neutron source. The PTRAC and F8 cards of MCNP allow to tally the time when a neutron is captured by {sup 3}He(n, p) reactions in the neutron detector. From this information, it is possible to build three different time distributions: neutron counts, Rossi-{alpha}, and Feynman-{alpha}. The neutron counts time distribution represents the number of neutrons captured as a function of time. The Rossi-a distribution represents the number of neutron pairs captured as a function of the time interval between two capture events. The Feynman-a distribution represents the variance-to-mean ratio, minus one, of the neutron counts array as a function of a fixed time interval. The MCNP6 results for these three time distributions have been compared with the experimental data of the YALINA Thermal facility and have been found to be in quite good agreement. (authors)

  9. The Design, Construction, and Initial Characterization of an Ultra-Low-Background Gas-Proportional Counting System

    SciTech Connect (OSTI)

    Seifert, Allen; Aalseth, Craig E.; Day, Anthony R.; Fuller, Erin S.; Hoppe, Eric W.; Keillor, Martin E.; Mace, Emily K.; Overman, Cory T.; Warren, Glen A.

    2013-05-01

    ABSTRACT Over the past several years, the Pacific Northwest National Laboratory (PNNL) has developed an ultra-low background proportional counter (ULBPC) technology. The resulting detector is the product of an effort to produce a low-background, physically robust gas proportional counter for applications like radon emanation measurements, groundwater tritium, and 37Ar. In order to fully take advantage of the inherent low-background properties designed into the ULBPC, a comparably low-background dedicated counting system is required. An ultra-low-background counting system (ULBCS) was recently built in the new shallow underground laboratory at PNNL. With a design depth of 30 meters water-equivalent, the shallow underground laboratory provides approximately 100x fewer fast neutrons and 6x fewer muons than a surface location. The ULBCS itself provides additional shielding in the form of active anti-cosmic veto (via 2-in. thick plastic scintillator paddles) and passive borated poly (1 in.), lead (6 in.), and copper (~3 in.) shielding. This work will provide details on PNNLs new shallow underground laboratory, examine the motivation for the design of the counting system, and provide results from the characterization of the ULBCS, including initial detector background.

  10. 235U Determination using In-Beam Delayed Neutron Counting Technique at the NRU Reactor

    SciTech Connect (OSTI)

    Andrews, M. T.; Bentoumi, G.; Corcoran, E. C.; Dimayuga, I.; Kelly, D. G.; Li, L.; Sur, B.; Rogge, R. B.

    2015-11-17

    This paper describes a collaborative effort that saw the Royal Military College of Canada (RMC)’s delayed neutron and gamma counting apparatus transported to Canadian Nuclear Laboratories (CNL) for use in the neutron beamline at the National Research Universal (NRU) reactor. Samples containing mg quantities of fissile material were re-interrogated, and their delayed neutron emissions measured. This collaboration offers significant advantages to previous delayed neutron research at both CNL and RMC. This paper details the determination of 235U content in enriched uranium via the assay of in-beam delayed neutron magnitudes and temporal behavior. 235U mass was determined with an average absolute error of ± 2.7 %. This error is lower than that obtained at RMCC for the assay of 235U content in aqueous solutions (3.6 %) using delayed neutron counting. Delayed neutron counting has been demonstrated to be a rapid, accurate, and precise method for special nuclear material detection and identification.

  11. Characteristic performance evaluation of a photon counting Si strip detector for low dose spectral breast CT imaging

    SciTech Connect (OSTI)

    Cho, Hyo-Min; Ding, Huanjun; Molloi, Sabee; Barber, William C.; Iwanczyk, Jan S.

    2014-09-15

    Purpose: The possible clinical applications which can be performed using a newly developed detector depend on the detector's characteristic performance in a number of metrics including the dynamic range, resolution, uniformity, and stability. The authors have evaluated a prototype energy resolved fast photon counting x-ray detector based on a silicon (Si) strip sensor used in an edge-on geometry with an application specific integrated circuit to record the number of x-rays and their energies at high flux and fast frame rates. The investigated detector was integrated with a dedicated breast spectral computed tomography (CT) system to make use of the detector's high spatial and energy resolution and low noise performance under conditions suitable for clinical breast imaging. The aim of this article is to investigate the intrinsic characteristics of the detector, in terms of maximum output count rate, spatial and energy resolution, and noise performance of the imaging system. Methods: The maximum output count rate was obtained with a 50 W x-ray tube with a maximum continuous output of 50 kVp at 1.0 mA. A{sup 109}Cd source, with a characteristic x-ray peak at 22 keV from Ag, was used to measure the energy resolution of the detector. The axial plane modulation transfer function (MTF) was measured using a 67 ?m diameter tungsten wire. The two-dimensional (2D) noise power spectrum (NPS) was measured using flat field images and noise equivalent quanta (NEQ) were calculated using the MTF and NPS results. The image quality parameters were studied as a function of various radiation doses and reconstruction filters. The one-dimensional (1D) NPS was used to investigate the effect of electronic noise elimination by varying the minimum energy threshold. Results: A maximum output count rate of 100 million counts per second per square millimeter (cps/mm{sup 2}) has been obtained (1 million cps per 100 100 ?m pixel). The electrical noise floor was less than 4 keV. The energy

  12. Low-noise low-jitter 32-pixels CMOS single-photon avalanche diodes array for single-photon counting from 300 nm to 900 nm

    SciTech Connect (OSTI)

    Scarcella, Carmelo; Tosi, Alberto Villa, Federica; Tisa, Simone; Zappa, Franco

    2013-12-15

    We developed a single-photon counting multichannel detection system, based on a monolithic linear array of 32 CMOS SPADs (Complementary Metal-Oxide-Semiconductor Single-Photon Avalanche Diodes). All channels achieve a timing resolution of 100 ps (full-width at half maximum) and a photon detection efficiency of 50% at 400 nm. Dark count rate is very low even at room temperature, being about 125 counts/s for 50 ?m active area diameter SPADs. Detection performance and microelectronic compactness of this CMOS SPAD array make it the best candidate for ultra-compact time-resolved spectrometers with single-photon sensitivity from 300 nm to 900 nm.

  13. A comparative analysis of OTF, NPS, and DQE in energy integrating and photon counting digital x-ray detectors

    SciTech Connect (OSTI)

    Acciavatti, Raymond J.; Maidment, Andrew D. A.

    2010-12-15

    Purpose: One of the benefits of photon counting (PC) detectors over energy integrating (EI) detectors is the absence of many additive noise sources, such as electronic noise and secondary quantum noise. The purpose of this work is to demonstrate that thresholding voltage gains to detect individual x rays actually generates an unexpected source of white noise in photon counters. Methods: To distinguish the two detector types, their point spread function (PSF) is interpreted differently. The PSF of the energy integrating detector is treated as a weighting function for counting x rays, while the PSF of the photon counting detector is interpreted as a probability. Although this model ignores some subtleties of real imaging systems, such as scatter and the energy-dependent amplification of secondary quanta in indirect-converting detectors, it is useful for demonstrating fundamental differences between the two detector types. From first principles, the optical transfer function (OTF) is calculated as the continuous Fourier transform of the PSF, the noise power spectra (NPS) is determined by the discrete space Fourier transform (DSFT) of the autocovariance of signal intensity, and the detective quantum efficiency (DQE) is found from combined knowledge of the OTF and NPS. To illustrate the calculation of the transfer functions, the PSF is modeled as the convolution of a Gaussian with the product of rect functions. The Gaussian reflects the blurring of the x-ray converter, while the rect functions model the sampling of the detector. Results: The transfer functions are first calculated assuming outside noise sources such as electronic noise and secondary quantum noise are negligible. It is demonstrated that while OTF is the same for two detector types possessing an equivalent PSF, a frequency-independent (i.e., ''white'') difference in their NPS exists such that NPS{sub PC}{>=}NPS{sub EI} and hence DQE{sub PC}{<=}DQE{sub EI}. The necessary and sufficient condition for

  14. A new method of passive counting of nuclear missile warheads -a white paper for the Defense Threat Reduction Agency

    SciTech Connect (OSTI)

    Morris, Christopher; Durham, J. Matthew; Guardincerri, Elena; Bacon, Jeffrey Darnell; Wang, Zhehui; Fellows, Shelby; Poulson, Daniel Cris; Plaud-Ramos, Kenie Omar; Daughton, Tess Marie; Johnson, Olivia Ruth

    2015-07-31

    Cosmic ray muon imaging has been studied for the past several years as a possible technique for nuclear warhead inspection and verification as part of the New Strategic Arms Reduction Treaty between the United States and the Russian Federation. The Los Alamos team has studied two different muon imaging methods for this application, using detectors on two sides and one side of the object of interest. In this report we present results obtained on single sided imaging of configurations aimed at demonstrating the potential of this technique for counting nuclear warheads in place with detectors above the closed hatch of a ballistic missile submarine.

  15. Characterizing energy dependence and count rate performance of a dual scintillator fiber-optic detector for computed tomography

    SciTech Connect (OSTI)

    Hoerner, Matthew R. Stepusin, Elliott J.; Hyer, Daniel E.; Hintenlang, David E.

    2015-03-15

    Purpose: Kilovoltage (kV) x-rays pose a significant challenge for radiation dosimetry. In the kV energy range, even small differences in material composition can result in significant variations in the absorbed energy between soft tissue and the detector. In addition, the use of electronic systems in light detection has demonstrated measurement losses at high photon fluence rates incident to the detector. This study investigated the feasibility of using a novel dual scintillator detector and whether its response to changes in beam energy from scatter and hardening is readily quantified. The detector incorporates a tissue-equivalent plastic scintillator and a gadolinium oxysulfide scintillator, which has a higher sensitivity to scatter x-rays. Methods: The detector was constructed by coupling two scintillators: (1) small cylindrical plastic scintillator, 500 μm in diameter and 2 mm in length, and (2) 100 micron sheet of gadolinium oxysulfide 500 μm in diameter, each to a 2 m long optical fiber, which acts as a light guide to transmit scintillation photons from the sensitive element to a photomultiplier tube. Count rate linearity data were obtained from a wide range of exposure rates delivered from a radiological x-ray tube by adjusting the tube current. The data were fitted to a nonparalyzable dead time model to characterize the time response. The true counting rate was related to the reference free air dose air rate measured with a 0.6 cm{sup 3} Radcal{sup ®} thimble chamber as described in AAPM Report No. 111. Secondary electron and photon spectra were evaluated using Monte Carlo techniques to analyze ionization quenching and photon energy-absorption characteristics from free-in-air and in phantom measurements. The depth/energy dependence of the detector was characterized using a computed tomography dose index QA phantom consisting of nested adult head and body segments. The phantom provided up to 32 cm of acrylic with a compatible 0.6 cm{sup 3} calibrated

  16. Faint submillimeter galaxies revealed by multifield deep ALMA observations: number counts, spatial clustering, and a dark submillimeter line emitter

    SciTech Connect (OSTI)

    Ono, Yoshiaki; Ouchi, Masami; Momose, Rieko; Kurono, Yasutaka

    2014-11-01

    We present the statistics of faint submillimeter/millimeter galaxies (SMGs) and serendipitous detections of a submillimeter/millimeter line emitter (SLE) with no multi-wavelength continuum counterpart revealed by the deep ALMA observations. We identify faint SMGs with flux densities of 0.1-1.0 mJy in the deep Band-6 and Band-7 maps of 10 independent fields that reduce cosmic variance effects. The differential number counts at 1.2 mm are found to increase with decreasing flux density down to 0.1 mJy. Our number counts indicate that the faint (0.1-1.0 mJy, or SFR{sub IR} ? 30-300 M {sub ?} yr{sup 1}) SMGs contribute nearly a half of the extragalactic background light (EBL), while the remaining half of the EBL is mostly contributed by very faint sources with flux densities of <0.1 mJy (SFR{sub IR} ? 30 M {sub ?} yr{sup 1}). We conduct counts-in-cells analysis with multifield ALMA data for the faint SMGs, and obtain a coarse estimate of galaxy bias, b {sub g} < 4. The galaxy bias suggests that the dark halo masses of the faint SMGs are ? 7 10{sup 12} M {sub ?}, which is smaller than those of bright (>1 mJy) SMGs, but consistent with abundant high-z star-forming populations, such as sBzKs, LBGs, and LAEs. Finally, we report the serendipitous detection of SLE-1, which has no continuum counterparts in our 1.2 mm-band or multi-wavelength images, including ultra deep HST/WFC3 and Spitzer data. The SLE has a significant line at 249.9 GHz with a signal-to-noise ratio of 7.1. If the SLE is not a spurious source made by the unknown systematic noise of ALMA, the strong upper limits of our multi-wavelength data suggest that the SLE would be a faint galaxy at z ? 6.

  17. A cascaded model of spectral distortions due to spectral response effects and pulse pileup effects in a photon-counting x-ray detector for CT

    SciTech Connect (OSTI)

    Cammin, Jochen E-mail: ktaguchi@jhmi.edu; Taguchi, Katsuyuki E-mail: ktaguchi@jhmi.edu; Xu, Jennifer; Barber, William C.; Iwanczyk, Jan S.; Hartsough, Neal E.

    2014-04-15

    Purpose: Energy discriminating, photon-counting detectors (PCDs) are an emerging technology for computed tomography (CT) with various potential benefits for clinical CT. The photon energies measured by PCDs can be distorted due to the interactions of a photon with the detector and the interaction of multiple coincident photons. These effects result in distorted recorded x-ray spectra which may lead to artifacts in reconstructed CT images and inaccuracies in tissue identification. Model-based compensation techniques have the potential to account for the distortion effects. This approach requires only a small number of parameters and is applicable to a wide range of spectra and count rates, but it needs an accurate model of the spectral distortions occurring in PCDs. The purpose of this study was to develop a model of those spectral distortions and to evaluate the model using a PCD (model DXMCT-1; DxRay, Inc., Northridge, CA) and various x-ray spectra in a wide range of count rates. Methods: The authors hypothesize that the complex phenomena of spectral distortions can be modeled by: (1) separating them into count-rate independent factors that we call the spectral response effects (SRE), and count-rate dependent factors that we call the pulse pileup effects (PPE), (2) developing separate models for SRE and PPE, and (3) cascading the SRE and PPE models into a combined SRE+PPE model that describes PCD distortions at both low and high count rates. The SRE model describes the probability distribution of the recorded spectrum, with a photo peak and a continuum tail, given the incident photon energy. Model parameters were obtained from calibration measurements with three radioisotopes and then interpolated linearly for other energies. The PPE model used was developed in the authors previous work [K. Taguchi et al., Modeling the performance of a photon counting x-ray detector for CT: Energy response and pulse pileup effects, Med. Phys. 38(2), 10891102 (2011)]. The

  18. Centroid Position as a Function of Total Counts in a Windowed CMOS Image of a Point Source

    SciTech Connect (OSTI)

    Wurtz, R E; Olivier, S; Riot, V; Hanold, B J; Figer, D F

    2010-05-27

    We obtained 960,200 22-by-22-pixel windowed images of a pinhole spot using the Teledyne H2RG CMOS detector with un-cooled SIDECAR readout. We performed an analysis to determine the precision we might expect in the position error signals to a telescope's guider system. We find that, under non-optimized operating conditions, the error in the computed centroid is strongly dependent on the total counts in the point image only below a certain threshold, approximately 50,000 photo-electrons. The LSST guider camera specification currently requires a 0.04 arcsecond error at 10 Hertz. Given the performance measured here, this specification can be delivered with a single star at 14th to 18th magnitude, depending on the passband.

  19. Free-running InGaAs single photon detector with 1 dark count per second at 10% efficiency

    SciTech Connect (OSTI)

    Korzh, B. Walenta, N.; Lunghi, T.; Gisin, N.; Zbinden, H.

    2014-02-24

    We present a free-running single photon detector for telecom wavelengths based on a negative feedback avalanche photodiode (NFAD). A dark count rate as low as 1?cps was obtained at a detection efficiency of 10%, with an afterpulse probability of 2.2% for 20??s of deadtime. This was achieved by using an active hold-off circuit and cooling the NFAD with a free-piston stirling cooler down to temperatures of ?110?C. We integrated two detectors into a practical, 625?MHz clocked quantum key distribution system. Stable, real-time key distribution in the presence of 30?dB channel loss was possible, yielding a secret key rate of 350?bps.

  20. Evaluation of two-stage system for neutron measurement aiming at increase in count rate at Japan Atomic Energy Agency-Fusion Neutronics Source

    SciTech Connect (OSTI)

    Shinohara, K. Ochiai, K.; Sukegawa, A.; Ishii, K.; Kitajima, S.; Baba, M.; Sasao, M.

    2014-11-15

    In order to increase the count rate capability of a neutron detection system as a whole, we propose a multi-stage neutron detection system. Experiments to test the effectiveness of this concept were carried out on Fusion Neutronics Source. Comparing four configurations of alignment, it was found that the influence of an anterior stage on a posterior stage was negligible for the pulse height distribution. The two-stage system using 25 mm thickness scintillator was about 1.65 times the count rate capability of a single detector system for d-D neutrons and was about 1.8 times the count rate capability for d-T neutrons. The results suggested that the concept of a multi-stage detection system will work in practice.

  1. HERSCHEL-ATLAS GALAXY COUNTS AND HIGH-REDSHIFT LUMINOSITY FUNCTIONS: THE FORMATION OF MASSIVE EARLY-TYPE GALAXIES

    SciTech Connect (OSTI)

    Lapi, A.; Gonzalez-Nuevo, J.; Fan, L.; Bressan, A.; De Zotti, G.; Danese, L.; Negrello, M.; Dunne, L.; Maddox, S.; Eales, S.; Auld, R.; Dariush, A.; Dye, S.; Baes, M.; Fritz, J.; Bonfield, D. G.; Buttiglione, S.; Cava, A.; Clements, D. L.; Cooray, A.

    2011-11-20

    Exploiting the Herschel Astrophysical Terahertz Large Area Survey Science Demonstration Phase survey data, we have determined the luminosity functions (LFs) at rest-frame wavelengths of 100 and 250 {mu}m and at several redshifts z {approx}> 1, for bright submillimeter galaxies with star formation rates (SFRs) {approx}> 100 M{sub Sun} yr{sup -1}. We find that the evolution of the comoving LF is strong up to z Almost-Equal-To 2.5, and slows down at higher redshifts. From the LFs and the information on halo masses inferred from clustering analysis, we derived an average relation between SFR and halo mass (and its scatter). We also infer that the timescale of the main episode of dust-enshrouded star formation in massive halos (M{sub H} {approx}> 3 Multiplication-Sign 10{sup 12} M{sub Sun }) amounts to {approx}7 Multiplication-Sign 10{sup 8} yr. Given the SFRs, which are in the range of 10{sup 2}-10{sup 3} M{sub Sun} yr{sup -1}, this timescale implies final stellar masses of the order of 10{sup 11}-10{sup 12} M{sub Sun }. The corresponding stellar mass function matches the observed mass function of passively evolving galaxies at z {approx}> 1. The comparison of the statistics for submillimeter and UV-selected galaxies suggests that the dust-free, UV bright phase is {approx}> 10{sup 2} times shorter than the submillimeter bright phase, implying that the dust must form soon after the onset of star formation. Using a single reference spectral energy distribution (SED; the one of the z Almost-Equal-To 2.3 galaxy SMM J2135-0102), our simple physical model is able to reproduce not only the LFs at different redshifts >1 but also the counts at wavelengths ranging from 250 {mu}m to Almost-Equal-To 1 mm. Owing to the steepness of the counts and their relatively broad frequency range, this result suggests that the dispersion of submillimeter SEDs of z > 1 galaxies around the reference one is rather small.

  2. ELLIPTICAL WEIGHTED HOLICs FOR WEAK LENSING SHEAR MEASUREMENT. III. THE EFFECT OF RANDOM COUNT NOISE ON IMAGE MOMENTS IN WEAK LENSING ANALYSIS

    SciTech Connect (OSTI)

    Okura, Yuki; Futamase, Toshifumi E-mail: tof@astr.tohoku.ac.jp

    2013-07-01

    This is the third paper on the improvement of systematic errors in weak lensing analysis using an elliptical weight function, referred to as E-HOLICs. In previous papers, we succeeded in avoiding errors that depend on the ellipticity of the background image. In this paper, we investigate the systematic error that depends on the signal-to-noise ratio of the background image. We find that the origin of this error is the random count noise that comes from the Poisson noise of sky counts. The random count noise makes additional moments and centroid shift error, and those first-order effects are canceled in averaging, but the second-order effects are not canceled. We derive the formulae that correct this systematic error due to the random count noise in measuring the moments and ellipticity of the background image. The correction formulae obtained are expressed as combinations of complex moments of the image, and thus can correct the systematic errors caused by each object. We test their validity using a simulated image and find that the systematic error becomes less than 1% in the measured ellipticity for objects with an IMCAT significance threshold of {nu} {approx} 11.7.

  3. An efficient parallel sampling technique for Multivariate Poisson-Lognormal model: Analysis with two crash count datasets

    SciTech Connect (OSTI)

    Zhan, Xianyuan; Aziz, H. M. Abdul; Ukkusuri, Satish V.

    2015-11-19

    Our study investigates the Multivariate Poisson-lognormal (MVPLN) model that jointly models crash frequency and severity accounting for correlations. The ordinary univariate count models analyze crashes of different severity level separately ignoring the correlations among severity levels. The MVPLN model is capable to incorporate the general correlation structure and takes account of the over dispersion in the data that leads to a superior data fitting. But, the traditional estimation approach for MVPLN model is computationally expensive, which often limits the use of MVPLN model in practice. In this work, a parallel sampling scheme is introduced to improve the original Markov Chain Monte Carlo (MCMC) estimation approach of the MVPLN model, which significantly reduces the model estimation time. Two MVPLN models are developed using the pedestrian vehicle crash data collected in New York City from 2002 to 2006, and the highway-injury data from Washington State (5-year data from 1990 to 1994) The Deviance Information Criteria (DIC) is used to evaluate the model fitting. The estimation results show that the MVPLN models provide a superior fit over univariate Poisson-lognormal (PLN), univariate Poisson, and Negative Binomial models. Moreover, the correlations among the latent effects of different severity levels are found significant in both datasets that justifies the importance of jointly modeling crash frequency and severity accounting for correlations.

  4. An efficient parallel sampling technique for Multivariate Poisson-Lognormal model: Analysis with two crash count datasets

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Zhan, Xianyuan; Aziz, H. M. Abdul; Ukkusuri, Satish V.

    2015-11-19

    Our study investigates the Multivariate Poisson-lognormal (MVPLN) model that jointly models crash frequency and severity accounting for correlations. The ordinary univariate count models analyze crashes of different severity level separately ignoring the correlations among severity levels. The MVPLN model is capable to incorporate the general correlation structure and takes account of the over dispersion in the data that leads to a superior data fitting. But, the traditional estimation approach for MVPLN model is computationally expensive, which often limits the use of MVPLN model in practice. In this work, a parallel sampling scheme is introduced to improve the original Markov Chainmore » Monte Carlo (MCMC) estimation approach of the MVPLN model, which significantly reduces the model estimation time. Two MVPLN models are developed using the pedestrian vehicle crash data collected in New York City from 2002 to 2006, and the highway-injury data from Washington State (5-year data from 1990 to 1994) The Deviance Information Criteria (DIC) is used to evaluate the model fitting. The estimation results show that the MVPLN models provide a superior fit over univariate Poisson-lognormal (PLN), univariate Poisson, and Negative Binomial models. Moreover, the correlations among the latent effects of different severity levels are found significant in both datasets that justifies the importance of jointly modeling crash frequency and severity accounting for correlations.« less

  5. Low-Intrusion Techniques and Sensitive Information Management for Warhead Counting and Verification: FY2011 Annual Report

    SciTech Connect (OSTI)

    Jarman, Kenneth D.; Robinson, Sean M.; McDonald, Benjamin S.; Gilbert, Andrew J.; Misner, Alex C.; Pitts, W. Karl; White, Timothy A.; Seifert, Allen; Miller, Erin A.

    2011-09-01

    Future arms control treaties may push nuclear weapons limits to unprecedented low levels and may entail precise counting of warheads as well as distinguishing between strategic and tactical nuclear weapons. Such advances will require assessment of form and function to confidently verify the presence or absence of nuclear warheads and/or their components. Imaging with penetrating radiation can provide such an assessment and could thus play a unique role in inspection scenarios. Yet many imaging capabilities have been viewed as too intrusive from the perspective of revealing weapon design details, and the potential for the release of sensitive information poses challenges in verification settings. A widely held perception is that verification through radiography requires images of sufficient quality that an expert (e.g., a trained inspector or an image-matching algorithm) can verify the presence or absence of components of a device. The concept of information barriers (IBs) has been established to prevent access to relevant weapon-design information by inspectors (or algorithms), and has, to date, limited the usefulness of radiographic inspection. The challenge of this project is to demonstrate that radiographic information can be used behind an IB to improve the capabilities of treaty-verification weapons-inspection systems.

  6. Full counting statistics as a probe of quantum coherence in a side-coupled double quantum dot system

    SciTech Connect (OSTI)

    Xue, Hai-Bin

    2013-12-15

    We study theoretically the full counting statistics of electron transport through side-coupled double quantum dot (QD) based on an efficient particle-number-resolved master equation. It is demonstrated that the high-order cumulants of transport current are more sensitive to the quantum coherence than the average current, which can be used to probe the quantum coherence of the considered double QD system. Especially, quantum coherence plays a crucial role in determining whether the super-Poissonian noise occurs in the weak inter-dot hopping coupling regime depending on the corresponding QD-lead coupling, and the corresponding values of super-Poissonian noise can be relatively enhanced when considering the spins of conduction electrons. Moreover, this super-Poissonian noise bias range depends on the singly-occupied eigenstates of the system, which thus suggests a tunable super-Poissonian noise device. The occurrence-mechanism of super-Poissonian noise can be understood in terms of the interplay of quantum coherence and effective competition between fast-and-slow transport channels. -- Highlights: The FCS can be used to probe the quantum coherence of side-coupled double QD system. Probing quantum coherence using FCS may permit experimental tests in the near future. The current noise characteristics depend on the quantum coherence of this QD system. The super-Poissonian noise can be enhanced when considering conduction electron spin. The side-coupled double QD system suggests a tunable super-Poissonian noise device.

  7. Event counting alpha detector

    DOE Patents [OSTI]

    Bolton, R.D.; MacArthur, D.W.

    1996-08-27

    An electrostatic detector is disclosed for atmospheric radon or other weak sources of alpha radiation. In one embodiment, nested enclosures are insulated from one another, open at the top, and have a high voltage pin inside and insulated from the inside enclosure. An electric field is produced between the pin and the inside enclosure. Air ions produced by collision with alpha particles inside the decay volume defined by the inside enclosure are attracted to the pin and the inner enclosure. With low alpha concentrations, individual alpha events can be measured to indicate the presence of radon or other alpha radiation. In another embodiment, an electrical field is produced between parallel plates which are insulated from a single decay cavity enclosure. 6 figs.

  8. Event counting alpha detector

    DOE Patents [OSTI]

    Bolton, Richard D.; MacArthur, Duncan W.

    1996-01-01

    An electrostatic detector for atmospheric radon or other weak sources of alpha radiation. In one embodiment, nested enclosures are insulated from one another, open at the top, and have a high voltage pin inside and insulated from the inside enclosure. An electric field is produced between the pin and the inside enclosure. Air ions produced by collision with alpha particles inside the decay volume defined by the inside enclosure are attracted to the pin and the inner enclosure. With low alpha concentrations, individual alpha events can be measured to indicate the presence of radon or other alpha radiation. In another embodiment, an electrical field is produced between parallel plates which are insulated from a single decay cavity enclosure.

  9. Counting paths in digraphs

    SciTech Connect (OSTI)

    Sullivan, Blair D; Seymour, Dr. Paul Douglas

    2010-01-01

    Say a digraph is k-free if it has no directed cycles of length at most k, for k {element_of} Z{sup +}. Thomasse conjectured that the number of induced 3-vertex directed paths in a simple 2-free digraph on n vertices is at most (n-1)n(n+1)/15. We present an unpublished result of Bondy proving there are at most 2n{sup 3}/25 such paths, and prove that for the class of circular interval digraphs, an upper bound of n{sup 3}/16 holds. We also study the problem of bounding the number of (non-induced) 4-vertex paths in 3-free digraphs. We show an upper bound of 4n{sup 4}/75 using Bondy's result for Thomasse's conjecture.

  10. Job Counting Guidelines

    Broader source: Energy.gov [DOE]

    The following updated definitions and guidelines are intended to provide EM Recovery Act sites with information to collect and report timely and accurate full‐time equivalent and cumulative head...

  11. Neutron Coincidence Counting Studies

    SciTech Connect (OSTI)

    Rogers, Jeremy L.; Ely, James H.; Kouzes, Richard T.; Lintereur, Azaree T.; Siciliano, Edward R.

    2012-08-31

    The efficiency comparison for measured and simulated responses of a 10B-lined proportional counter and a 3He proportional counter in a close, symmetrical geometry are presented. The measurement geometry was modeled in MCNPX to validate the methods used for simulating the response of both the 3He and 10B-lined tubes. The MCNPX models agree within 1% with the 3He tube measurements and within 3% for the 10B-lined tubes when a 0.75-µm boron-metal lining is used.

  12. Detection of illicit HEU production in gaseous centrifuge enrichment plants using neutron counting techniques on product cylinders

    SciTech Connect (OSTI)

    Freeman, Corey R; Geist, William H

    2010-01-01

    Innovative and novel safeguards approaches are needed for nuclear energy to meet global energy needs without the threat of nuclear weapons proliferation. Part of these efforts will include creating verification techniques that can monitor uranium enrichment facilities for illicit production of highly-enriched uranium (HEU). Passive nondestructive assay (NDA) techniques will be critical in preventing illicit HEU production because NDA offers the possibility of continuous and unattended monitoring capabilities with limited impact on facility operations. Gaseous centrifuge enrichment plants (GCEP) are commonly used to produce low-enriched uranium (LEU) for reactor fuel. In a GCEP, gaseous UF{sub 6} spins at high velocities in centrifuges to separate the molecules containing {sup 238}U from those containing the lighter {sup 235}U. Unfortunately, the process for creating LEU is inherently the same as HEU, creating a proliferation concern. Insuring that GCEPs are producing declared enrichments poses many difficult challenges. In a GCEP, large cascade halls operating thousands of centrifuges work together to enrich the uranium which makes effective monitoring of the cascade hall economically prohibitive and invasive to plant operations. However, the enriched uranium exiting the cascade hall fills product cylinders where the UF{sub 6} gas sublimes and condenses for easier storage and transportation. These product cylinders hold large quantities of enriched uranium, offering a strong signal for NDA measurement. Neutrons have a large penetrability through materials making their use advantageous compared to gamma techniques where the signal is easily attenuated. One proposed technique for detecting HEU production in a GCEP is using neutron coincidence counting at the product cylinder take off stations. This paper discusses findings from Monte Carlo N-Particle eXtended (MCNPX) code simulations that examine the feasibility of such a detector.

  13. CNTA_Well_Pad_restoration_ltr.pdf

    Office of Legacy Management (LM)

  14. FC-PAD Organization and Activities

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... electron microscopy (STEM) Atomic resolution imaging Electron Energy ... using electrochemical techniques X-ray absorption spectroscopy for catalyst ...

  15. Ideal-observer detectability in photon-counting differential phase-contrast imaging using a linear-systems approach

    SciTech Connect (OSTI)

    Fredenberg, Erik; Danielsson, Mats; Stayman, J. Webster; Siewerdsen, Jeffrey H.; Aslund, Magnus

    2012-09-15

    Purpose: To provide a cascaded-systems framework based on the noise-power spectrum (NPS), modulation transfer function (MTF), and noise-equivalent number of quanta (NEQ) for quantitative evaluation of differential phase-contrast imaging (Talbot interferometry) in relation to conventional absorption contrast under equal-dose, equal-geometry, and, to some extent, equal-photon-economy constraints. The focus is a geometry for photon-counting mammography. Methods: Phase-contrast imaging is a promising technology that may emerge as an alternative or adjunct to conventional absorption contrast. In particular, phase contrast may increase the signal-difference-to-noise ratio compared to absorption contrast because the difference in phase shift between soft-tissue structures is often substantially larger than the absorption difference. We have developed a comprehensive cascaded-systems framework to investigate Talbot interferometry, which is a technique for differential phase-contrast imaging. Analytical expressions for the MTF and NPS were derived to calculate the NEQ and a task-specific ideal-observer detectability index under assumptions of linearity and shift invariance. Talbot interferometry was compared to absorption contrast at equal dose, and using either a plane wave or a spherical wave in a conceivable mammography geometry. The impact of source size and spectrum bandwidth was included in the framework, and the trade-off with photon economy was investigated in some detail. Wave-propagation simulations were used to verify the analytical expressions and to generate example images. Results: Talbot interferometry inherently detects the differential of the phase, which led to a maximum in NEQ at high spatial frequencies, whereas the absorption-contrast NEQ decreased monotonically with frequency. Further, phase contrast detects differences in density rather than atomic number, and the optimal imaging energy was found to be a factor of 1.7 higher than for absorption

  16. Investigating the limits of PET/CT imaging at very low true count rates and high random fractions in ion-beam therapy monitoring

    SciTech Connect (OSTI)

    Kurz, Christopher Bauer, Julia; Conti, Maurizio; Guérin, Laura; Eriksson, Lars; Parodi, Katia

    2015-07-15

    Purpose: External beam radiotherapy with protons and heavier ions enables a tighter conformation of the applied dose to arbitrarily shaped tumor volumes with respect to photons, but is more sensitive to uncertainties in the radiotherapeutic treatment chain. Consequently, an independent verification of the applied treatment is highly desirable. For this purpose, the irradiation-induced β{sup +}-emitter distribution within the patient is detected shortly after irradiation by a commercial full-ring positron emission tomography/x-ray computed tomography (PET/CT) scanner installed next to the treatment rooms at the Heidelberg Ion-Beam Therapy Center (HIT). A major challenge to this approach is posed by the small number of detected coincidences. This contribution aims at characterizing the performance of the used PET/CT device and identifying the best-performing reconstruction algorithm under the particular statistical conditions of PET-based treatment monitoring. Moreover, this study addresses the impact of radiation background from the intrinsically radioactive lutetium-oxyorthosilicate (LSO)-based detectors at low counts. Methods: The authors have acquired 30 subsequent PET scans of a cylindrical phantom emulating a patientlike activity pattern and spanning the entire patient counting regime in terms of true coincidences and random fractions (RFs). Accuracy and precision of activity quantification, image noise, and geometrical fidelity of the scanner have been investigated for various reconstruction algorithms and settings in order to identify a practical, well-suited reconstruction scheme for PET-based treatment verification. Truncated listmode data have been utilized for separating the effects of small true count numbers and high RFs on the reconstructed images. A corresponding simulation study enabled extending the results to an even wider range of counting statistics and to additionally investigate the impact of scatter coincidences. Eventually, the recommended

  17. A Pixel Readout Chip in 40 nm CMOS Process for High Count Rate Imaging Systems with Minimization of Charge Sharing Effects

    SciTech Connect (OSTI)

    Maj, Piotr; Grybos, P.; Szczgiel, R.; Kmon, P.; Drozd, A.; Deptuch, G.

    2013-11-07

    We present a prototype chip in 40 nm CMOS technology for readout of hybrid pixel detector. The prototype chip has a matrix of 18x24 pixels with a pixel pitch of 100 ?m. It can operate both in single photon counting (SPC) mode and in C8P1 mode. In SPC the measured ENC is 84 e? rms (for the peaking time of 48 ns), while the effective offset spread is below 2 mV rms. In the C8P1 mode the chip reconstructs full charge deposited in the detector, even in the case of charge sharing, and it identifies a pixel with the largest charge deposition. The chip architecture and preliminary measurements are reported.

  18. Determination of total Pu content in a Spent Fuel Assembly by Measuring Passive Neutron Count rate and Multiplication with the Differential Die-Away Instrument

    SciTech Connect (OSTI)

    Henzl, Vladimir; Croft, Stephen; Swinhoe, Martyn T.; Tobin, Stephen J.

    2012-07-18

    A key objective of the Next Generation Safeguards Initiative (NGSI) is to evaluate and develop non-destructive assay (NDA) techniques to determine the elemental plutonium content in a commercial-grade nuclear spent fuel assembly (SFA) [1]. Within this framework, we investigate by simulation a novel analytical approach based on combined information from passive measurement of the total neutron count rate of a SFA and its multiplication determined by the active interrogation using an instrument based on a Differential Die-Away technique (DDA). We use detailed MCNPX simulations across an extensive set of SFA characteristics to establish the approach and demonstrate its robustness. It is predicted that Pu content can be determined by the proposed method to a few %.

  19. Direct Deposition of Microcolumnar Scintillator on CMOS SSPM Array: Toward a Photon Counting Detector for X-Ray/Gamma Ray Imaging

    SciTech Connect (OSTI)

    Prekas, G.; Breen, M.; Sabet, H.; Bhandari, H.; Derderian, G.; Robertson, F. Jr; Stapels, C. J.; Christian, J.; Cool, S.; Nagarkar, V. V.

    2011-12-13

    We are developing a modular, low-cost, photon-counting detector based on a scintillator coupled to a solid-state photodetector. A working prototype was successfully developed by depositing CsI:Tl directly onto a CMOS SSPM array designed by RMD and custom-fabricated by a commercial foundry. The device comprised a 6x6 array of 1.5x1.5 mm{sup 2} macro-pixels, each containing a 36x36 array of resistively coupled micro-pixels, that was subjected to vapor deposition of columnar CsI:Tl. Direct deposition eliminates the gap between the scintillator and SSPM and creates a better optical bond than does index-matching grease. This paper compares the performance of SSPMs with directly deposited CsI:Tl, in terms of signal-to-noise ratio and light spread, against devices using monolithic single crystals or pixelated single crystals coupled to the SSPM. Due to the reduction in light scattering and optical losses in the interface, the directly deposited CsI:Tl demonstrated significantly better position sensitivity, with at least a factor of 2 increase in SNR compared to a single crystal. These data indicate that a photodetector with substantially smaller macro-pixel dimensions than used here could be used to implement a low-energy X-ray/gamma-ray imaging and spectroscopy detector, particularly for applications where high resolution is of prime importance.

  20. Channel-capacity gain in entanglement-assisted communication protocols based exclusively on linear optics, single-photon inputs, and coincidence photon counting

    SciTech Connect (OSTI)

    Lougovski, P.; Uskov, D. B.

    2015-08-04

    Entanglement can effectively increase communication channel capacity as evidenced by dense coding that predicts a capacity gain of 1 bit when compared to entanglement-free protocols. However, dense coding relies on Bell states and when implemented using photons the capacity gain is bounded by 0.585 bits due to one's inability to discriminate between the four optically encoded Bell states. In this research we study the following question: Are there alternative entanglement-assisted protocols that rely only on linear optics, coincidence photon counting, and separable single-photon input states and at the same time provide a greater capacity gain than 0.585 bits? In this study, we show that besides the Bell states there is a class of bipartite four-mode two-photon entangled states that facilitate an increase in channel capacity. We also discuss how the proposed scheme can be generalized to the case of two-photon N-mode entangled states for N=6,8.

  1. Channel-capacity gain in entanglement-assisted communication protocols based exclusively on linear optics, single-photon inputs, and coincidence photon counting

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Lougovski, P.; Uskov, D. B.

    2015-08-04

    Entanglement can effectively increase communication channel capacity as evidenced by dense coding that predicts a capacity gain of 1 bit when compared to entanglement-free protocols. However, dense coding relies on Bell states and when implemented using photons the capacity gain is bounded by 0.585 bits due to one's inability to discriminate between the four optically encoded Bell states. In this research we study the following question: Are there alternative entanglement-assisted protocols that rely only on linear optics, coincidence photon counting, and separable single-photon input states and at the same time provide a greater capacity gain than 0.585 bits? In thismore » study, we show that besides the Bell states there is a class of bipartite four-mode two-photon entangled states that facilitate an increase in channel capacity. We also discuss how the proposed scheme can be generalized to the case of two-photon N-mode entangled states for N=6,8.« less

  2. ECUADOR: counting down the barrels

    SciTech Connect (OSTI)

    Not Available

    1983-02-09

    Within the world oil market, OPEC faces a reduced role as supplier and production/price dilemmas. One of its members, Ecuador, faces rapid drawdown of its reserves and ultimate loss of membership in the cartel. But Ecuador is tackling the problem by a variety of means and is still defending OPEC prices, as its OPEC Governor tells Energy Detente. The complete interview with Cesar Guerra Navarrete, the OPEC Governor is presented. The Energy Detente fuel price/tax series and the principal industrial fuel prices as of February 1983 are included for countries of the Eastern Hemisphere.

  3. Low Background Counting at LBNL

    Office of Scientific and Technical Information (OSTI)

    ... doi:10.1016Zj.phpro.2014.12.101 788 A.R. Smith et al. Physics Procedia 61 (2015) 787 - ... began in the summer of 1975 when A.R. Smith established contacts there with the ...

  4. Opcode counting for performance measurement

    DOE Patents [OSTI]

    Gara, Alan; Satterfield, David L.; Walkup, Robert E.

    2015-08-11

    Methods, systems and computer program products are disclosed for measuring a performance of a program running on a processing unit of a processing system. In one embodiment, the method comprises informing a logic unit of each instruction in the program that is executed by the processing unit, assigning a weight to each instruction, assigning the instructions to a plurality of groups, and analyzing the plurality of groups to measure one or more metrics. In one embodiment, each instruction includes an operating code portion, and the assigning includes assigning the instructions to the groups based on the operating code portions of the instructions. In an embodiment, each type of instruction is assigned to a respective one of the plurality of groups. These groups may be combined into a plurality of sets of the groups.

  5. Opcode counting for performance measurement

    DOE Patents [OSTI]

    Gara, Alan; Satterfield, David L; Walkup, Robert E

    2013-10-29

    Methods, systems and computer program products are disclosed for measuring a performance of a program running on a processing unit of a processing system. In one embodiment, the method comprises informing a logic unit of each instruction in the program that is executed by the processing unit, assigning a weight to each instruction, assigning the instructions to a plurality of groups, and analyzing the plurality of groups to measure one or more metrics. In one embodiment, each instruction includes an operating code portion, and the assigning includes assigning the instructions to the groups based on the operating code portions of the instructions. In an embodiment, each type of instruction is assigned to a respective one of the plurality of groups. These groups may be combined into a plurality of sets of the groups.

  6. Individual Radiological Protection Monitoring of Utrok Atoll Residents Based on Whole Body Counting of Cesium-137 (137Cs) and Plutonium Bioassay

    SciTech Connect (OSTI)

    Hamilton, T; Kehl, S; Brown, T; Martinelli, R; Hickman, D; Jue, T; Tumey, S; Langston, R

    2007-06-08

    This report contains individual radiological protection surveillance data developed during 2006 for adult members of a select group of families living on Utrok Atoll. These Group I volunteers all underwent a whole-body count to determine levels of internally deposited cesium-137 ({sup 137}Cs) and supplied a bioassay sample for analysis of plutonium isotopes. Measurement data were obtained and the results compared with an equivalent set of measurement data for {sup 137}Cs and plutonium isotopes from a second group of adult volunteers (Group II) who were long-term residents of Utrok Atoll. For the purposes of this comparison, Group II volunteers were considered representative of the general population on Utrok Atoll. The general aim of the study was to determine residual systemic burdens of fallout radionuclides in each volunteer group, develop data in response to addressing some specific concerns about the preferential uptake and potential health consequences of residual fallout radionuclides in Group I volunteers, and generally provide some perspective on the significance of radiation doses delivered to volunteers (and the general Utrok Atoll resident population) in terms of radiological protection standards and health risks. Based on dose estimates from measurements of internally deposited {sup 137}Cs and plutonium isotopes, the data and information developed in this report clearly show that neither volunteer group has acquired levels of internally deposited fallout radionuclides specific to nuclear weapons testing in the Marshall Islands that are likely to have any consequence on human health. Moreover, the dose estimates are well below radiological protection standards as prescribed by U.S. regulators and international agencies, and are very small when compared to doses from natural sources of radiation in the Marshall Islands and the threshold where radiation health effects could be either medically diagnosed in an individual or epidemiologically discerned in a

  7. What is the best method to fit time-resolved data? A comparison of the residual minimization and the maximum likelihood techniques as applied to experimental time-correlated, single-photon counting data

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Santra, Kalyan; Zhan, Jinchun; Song, Xueyu; Smith, Emily A.; Vaswani, Namrata; Petrich, Jacob W.

    2016-02-10

    The need for measuring fluorescence lifetimes of species in subdiffraction-limited volumes in, for example, stimulated emission depletion (STED) microscopy, entails the dual challenge of probing a small number of fluorophores and fitting the concomitant sparse data set to the appropriate excited-state decay function. This need has stimulated a further investigation into the relative merits of two fitting techniques commonly referred to as “residual minimization” (RM) and “maximum likelihood” (ML). Fluorescence decays of the well-characterized standard, rose bengal in methanol at room temperature (530 ± 10 ps), were acquired in a set of five experiments in which the total number ofmore » “photon counts” was approximately 20, 200, 1000, 3000, and 6000 and there were about 2–200 counts at the maxima of the respective decays. Each set of experiments was repeated 50 times to generate the appropriate statistics. Each of the 250 data sets was analyzed by ML and two different RM methods (differing in the weighting of residuals) using in-house routines and compared with a frequently used commercial RM routine. Convolution with a real instrument response function was always included in the fitting. While RM using Pearson’s weighting of residuals can recover the correct mean result with a total number of counts of 1000 or more, ML distinguishes itself by yielding, in all cases, the same mean lifetime within 2% of the accepted value. For 200 total counts and greater, ML always provides a standard deviation of <10% of the mean lifetime, and even at 20 total counts there is only 20% error in the mean lifetime. Here, the robustness of ML advocates its use for sparse data sets such as those acquired in some subdiffraction-limited microscopies, such as STED, and, more importantly, provides greater motivation for exploiting the time-resolved capacities of this technique to acquire and analyze fluorescence lifetime data.« less

  8. Working and Net Available Shell Storage Capacity as of September...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    for PAD District 2 and the U.S. total have been revised to correct a processing error that caused some capacity data to be double counted in the original release of this...

  9. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Rail between PAD Districts

  10. Monitoring of the Airport Calibration Pads at Walker Field, Grand...

    Broader source: Energy.gov (indexed) [DOE]

    More Documents & Publications Field Calibration Facilities for Environmental Measurement of Radium, Thorium, and Potassium (October 2013) UMTRCA Sites Fact Sheet Long-Term ...

  11. Exposure-Rate Calibration Using Large-Area Calibration Pads ...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Measurement of Radium, Thorium, and Potassium (October 2013) Field Calibration Facilities for Environmental Measurement of Radium, Thorium, and Potassium (June 1994) ...

  12. Paducah Site Annual Site Environmental Report PAD-REG-1021

    Office of Environmental Management (EM)

    ... Performance ...... 2-13 2.7 EMERGENCY PLANNING AND COMMUNITY RIGHT TO KNOW ACT AND ... Changes of particular importance are (1) increased the focus on human health problems ...

  13. Crude Oil and Petroleum Products Movements by Pipeline between PAD

    U.S. Energy Information Administration (EIA) Indexed Site

    Districts Product: Crude Oil and Petroleum Products Crude Oil Petroleum Products Pentanes Plus Liquefied Petroleum Gases Ethane/Ethylene Propane/Propylene Isobutane/Isobutylene Normal Butane/Butylene Motor Gasoline Blend. Comp. (MGBC) MGBC - Reformulated MGBC - Reformulated RBOB MGBC - RBOB for Blending w/ Alcohol* MGBC - Conventional MGBC - CBOB MGBC - Conventional GTAB MGBC - Conventional Other Renewable Fuels Renewable Diesel Fuel Finished Motor Gasoline Reformulated Gasoline Conventional

  14. SEP Success Story: Green Launching Pad Taps Six More Companies...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    April 29, 2011 - 9:58am Addthis Yesterday, U.S. Secretary of Energy Steven Chu joined New Hampshire Governor John Lynch and University of New Hampshire (UNH) President Mark W. ...

  15. Guidance on the Use of Hand-Held Survey Meters for radiological Triage: Time-Dependent Detector Count Rates Corresponding to 50, 250, and 500 mSv Effective Dose for Adult Males and Adult Females

    SciTech Connect (OSTI)

    Bolch, W.E.; Hurtado, J.L.; Lee, C.; Manger, Ryan P; Hertel, Nolan; Burgett, E.; Dickerson, W.

    2012-01-01

    In June 2006, the Radiation Studies Branch of the Centers for Disease Control and Prevention held a workshop to explore rapid methods of facilitating radiological triage of large numbers of potentially contaminated individuals following detonation of a radiological dispersal device. Two options were discussed. The first was the use of traditional gamma cameras in nuclear medicine departments operated as makeshift wholebody counters. Guidance on this approach is currently available from the CDC. This approach would be feasible if a manageable number of individuals were involved, transportation to the relevant hospitals was quickly provided, and the medical staff at each facility had been previously trained in this non-traditional use of their radiopharmaceutical imaging devices. If, however, substantially larger numbers of individuals (100 s to 1,000 s) needed radiological screening, other options must be given to first responders, first receivers, and health physicists providing medical management. In this study, the second option of the workshop was investigated by the use of commercially available portable survey meters (either NaI or GM based) for assessing potential ranges of effective dose (G50, 50Y250, 250Y500, and 9500 mSv). Two hybrid computational phantoms were used to model an adult male and an adult female subject internally contaminated with 241Am, 60Cs, 137Cs, 131I, or 192Ir following an acute inhalation or ingestion intake. As a function of time following the exposure, the net count rates corresponding to committed effective doses of 50, 250, and 500 mSv were estimated via Monte Carlo radiation transport simulation for each of four different detector types, positions, and screening distances. Measured net count rates can be compared to these values, and an assignment of one of four possible effective dose ranges could be made. The method implicitly assumes that all external contamination has been removed prior to screening and that the measurements be

  16. Opportunities for Decay Counting of Environmental Radioisotopes...

    Office of Scientific and Technical Information (OSTI)

    Close Cite: Bibtex Format Close 0 pages in this document matching the terms "" Search For Terms: Enter terms in the toolbar above to search the full text of this document for ...

  17. Two Million Smart Meters and Counting

    Office of Energy Efficiency and Renewable Energy (EERE)

    A major milestone towards the implementation of smart grid technologies, which an analysis found could reduce electricity use by more than four percent annually by 2030 –- that would mean consumers around the country would see savings of over $20 billion each year.

  18. Improving Photoelectron Counting and Particle Identification...

    Office of Scientific and Technical Information (OSTI)

    ; Gorel, P. ; Graham, K. ; Grace, E. ; Guerrero, N. ; Guiseppe, V. ; Hallin, A. L. ; Harvey, P. ; Hearns, C. ; Henning, R. ; Hime, Andrew ; Hofgartner, J. ; Jaditz, S. ; ...

  19. 2013 Feds Feed Families: Your Generosity Counts

    Broader source: Energy.gov [DOE]

    Federal employees are asked to help local food banks replenish supplies for the hungry during the summer months.

  20. Counting molecular-beam grown graphene layers

    SciTech Connect (OSTI)

    Plaut, Annette S.; Wurstbauer, Ulrich; Pinczuk, Aron; Department of Applied Physics and Applied Mathematics, Columbia University, New York, New York 10027 ; Garcia, Jorge M.; Pfeiffer, Loren N.

    2013-06-17

    We have used the ratio of the integrated intensity of graphene's Raman G peak to that of the silicon substrate's first-order optical phonon peak, accurately to determine the number of graphene layers across our molecular-beam (MB) grown graphene films. We find that these results agree well both, with those from our own exfoliated single and few-layer graphene flakes, and with the results of Koh et al.[ACS Nano 5, 269 (2011)]. We hence distinguish regions of single-, bi-, tri-, four-layer, etc., graphene, consecutively, as we scan coarsely across our MB-grown graphene. This is the first, but crucial, step to being able to grow, by such molecular-beam-techniques, a specified number of large-area graphene layers, to order.

  1. Counting graphene layers with very slow electrons

    SciTech Connect (OSTI)

    Frank, Lud?k; Mikmekov, Elika; Mllerov, Ilona; Lejeune, Michal

    2015-01-05

    The study aimed at collection of data regarding the transmissivity of freestanding graphene for electrons across their full energy scale down to the lowest energies. Here, we show that the electron transmissivity of graphene drops with the decreasing energy of the electrons and remains below 10% for energies below 30?eV, and that the slow electron transmissivity value is suitable for reliable determination of the number of graphene layers. Moreover, electrons incident below 50?eV release adsorbed hydrocarbon molecules and effectively clean graphene in contrast to faster electrons that decompose these molecules and create carbonaceous contamination.

  2. Count Directive No. Title OPI Approval Date

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Preservation Award | Department of Energy Council Honors Oak Ridge's EM Program with Prestigious Historic Preservation Award Council Honors Oak Ridge's EM Program with Prestigious Historic Preservation Award August 15, 2016 - 12:35pm Addthis Left to right, ACHP Chairman Milford Wayne Donaldson; Knox Heritage Executive Director Kim Trent; OREM Manager Sue Cange; and ACHP Expert Member Robert Stanton with the Chairman’s Award for Achievement in Historic Preservation. Left to right, ACHP

  3. Crude Oil Movements by Tanker, Pipeline, Barge and Rail between PAD

    U.S. Energy Information Administration (EIA) Indexed Site

    Districts 2010 2011 2012 2013 2014 2015 View History From PADD 1 to PADD 2 274 590 1,646 2,729 3,915 2,727 1981-2015 PADD 3 9,242 13,779 3,624 9,369 11,607 8,639 1981-2015 PADD 4 0 0 0 2013-2015 PADD 5 20 2011-2011 From PADD 2 to PADD 1 6,186 7,683 24,235 84,910 140,671 141,332 1981-2015 PADD 3 56,820 86,484 176,744 270,731 305,252 372,799 1981-2015 PADD 4 22,494 27,587 33,807 25,727 40,502 75,117 1981-2015 PADD 5 453 1,608 7,948 33,172 52,932 50,063 2010-2015 From PADD 3 to PADD 1 10,096

  4. Crude Oil Movements of Crude of by Rail between PAD Districts

    U.S. Energy Information Administration (EIA) Indexed Site

    Product: Crude Oil Fuel Ethanol Biodiesel Period-Unit: Monthly-Thousand Barrels Annual-Thousand Barrels Download Series History Download Series History Definitions, Sources & Notes ...

  5. Year Month U.S. Average PAD District I Average CT ME MA NH RI

    Gasoline and Diesel Fuel Update (EIA)

    1994 January ... 89.6 91.0 90.2 83.8 88.4 80.4 87.3 88.8 92.1 102.5 February ... 92.9 94.6 93.8 90.4 91.3 86.6 91.4 92.3 91.5 105.5...

  6. Year Month U.S. Average PAD District I Average CT ME MA NH RI

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    1993 January ... 94.3 95.7 94.9 85.2 94.0 87.1 91.7 93.4 91.2 105.2 February ... 94.6 95.9 96.2 85.4 94.4 86.9 91.8 93.3 90.8 106.8...

  7. Year Month U.S. Average PAD District I Average CT ME MA NH RI

    U.S. Energy Information Administration (EIA) Indexed Site

    1995 January ... 86.9 87.6 86.7 77.8 84.8 78.4 87.3 85.7 88.4 102.4 February ... 87.4 88.2 87.8 77.4 84.9 78.5 87.3 85.9 88.5 103.4...

  8. Year Month U.S. Average PAD District I Average CT ME MA NH RI

    Gasoline and Diesel Fuel Update (EIA)

    1996 January ... 94.6 96.1 94.5 93.0 92.0 89.1 94.9 92.6 94.7 111.7 February ... 95.9 97.5 96.2 93.2 93.8 90.8 95.6 93.7 94.4 112.9...

  9. Year Month U.S. Average PAD District I Average CT ME MA NH RI

    U.S. Energy Information Administration (EIA) Indexed Site

    1997 January ... 107.9 109.0 108.6 105.2 106.5 102.1 107.0 104.4 106.5 130.4 February ... 105.1 106.0 105.2 102.2 103.4 101.0 104.5...

  10. Construction of MV-6 Well Pad at the Central Nevada Test Area Completed

    Office of Energy Efficiency and Renewable Energy (EERE)

    A new groundwater monitoring/validation (MV) well was installed at the Central Nevada Test Area (CNTA) in September 2013. LM proposed this well to the Nevada Division of Environmental Protection ...

  11. Table 42. Residual Fuel Oil Prices by PAD District and State

    U.S. Energy Information Administration (EIA) Indexed Site

    33.7 27.5 25.9 23.4 28.0 25.3 February ... 31.8 22.3 24.8 21.6 26.9 21.8 March ... 32.8 27.0 26.7 24.2 28.5 25.3 April...

  12. Crude Oil Movements of Crude of by Rail between PAD Districts

    U.S. Energy Information Administration (EIA) Indexed Site

    2010 2011 2012 2013 2014 2015 View History From PADD 1 to PADD 2 0 0 0 0 0 0 2010-2015 ... See movements of crude oil by rail for movements by rail within PADDs and tofrom Canada. ...

  13. PAD: Polymer-Assisted Deposition of Metal-Oxide and Metal-Nitride...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    optics (e.g., lasers) Opto-electric materials and components Hardened coatings Microelectronics Patents and Patent Applications ID Number Title and Abstract Primary Lab Date...

  14. Crude Oil Movements by Tanker, Pipeline, Barge and Rail between PAD

    U.S. Energy Information Administration (EIA) Indexed Site

    Districts 15 90 125 91 76 73 1986-2016 PADD 3 201 104 0 18 21 38 1986-2016 PADD 4 0 0 2013-2016 PADD 5 2011-2011 From PADD 2 to PADD 1 8,614 6,677 7,556 4,377 6,185 4,536 1986-2016 PADD 3 30,165 26,514 32,150 33,114 29,021 29,329 1986-2016 PADD 4 6,943 7,365 7,150 6,217 6,776 7,264 1986-2016 PADD 5 3,894 3,511 4,977 4,079 3,875 3,824 2010-2016 From PADD 3 to PADD 1 1,388 1,128 509 2,281 1,560 1,318 1986-2016 PADD 2 19,539 17,229 17,509 22,895 27,473 26,217 1986-2016 PADD 4 0 0 0 0 0 0

  15. Crude Oil Movements of Crude of by Rail between PAD Districts

    U.S. Energy Information Administration (EIA) Indexed Site

    Jan-16 Feb-16 Mar-16 Apr-16 May-16 Jun-16 View History From PADD 1 to PADD 2 0 0 0 0 0 0 2010-2016 PADD 4 0 0 2013-2016 From PADD 2 to PADD 1 8,122 6,207 7,082 3,900 5,614 3,952 2010-2016 PADD 3 1,692 1,310 1,075 1,585 1,865 933 2010-2016 PADD 4 0 2012-2016 PADD 5 3,894 3,511 4,977 4,079 3,875 3,824 2010-2016 From PADD 3 to PADD 2 0 0 0 0 0 0 2010-2016 PADD 4 0 0 0 0 0 0 2010-2016 PADD 5 26 135 79 26 2012-2016 From PADD 4 to PADD 1 286 297 2013-2016 PADD 2 0 2012-2016 PADD 3 1,139 1,347 717 992

  16. Crude Oil Net Receipts by Pipeline, Tanker, Barge and Rail between PAD

    U.S. Energy Information Administration (EIA) Indexed Site

    Districts 9,972 7,611 8,237 6,549 7,648 5,743 1981-2016 Midwest (PADD 2) -13,182 -10,465 -17,452 -7,812 -1,468 -3,442 1981-2016 Gulf Coast (PADD 3) 11,024 9,848 15,079 9,293 2,343 3,768 1981-2016 Rocky Mountain (PADD 4) -11,794 -10,738 -10,920 -12,189 -12,399 -9,893 1986-2016 West Coast (PADD 5) 3,980 3,743 5,056 4,159 3,875 3,824

  17. Crude Oil and Petroleum Products Movements by Tanker and Barge between PAD

    U.S. Energy Information Administration (EIA) Indexed Site

    Districts Product: Crude Oil and Petroleum Products Crude Oil Petroleum Products Liquefied Petroleum Gases Propane/Propylene Unfinished Oils Motor Gasoline Blending Components MGBC - Reformulated MGBC - Reformulated RBOB MGBC - RBOB for Blending w/ Alcohol* MGBC - RBOB for Blending w/ Ether* MGBC - Reformulated GTAB* MGBC - Conventional MGBC - CBOB MGBC - Conventional GTAB MGBC - Conventional Other Renewable Fuels Fuel Ethanol Renewable Diesel Fuel Other Renewable Fuels Finished Motor

  18. Webinar January 7: FCTO Consortia Overview Webinar (FC-PAD and...

    Broader source: Energy.gov (indexed) [DOE]

    To accelerate the rate of progress in developing technologies to improve the performance and durability of proton exchange membrane (PEM) fuel cell systems and to develop advanced ...

  19. FCTO Consortia Overview (HyMARC and FC-PAD) Webinar

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Spectroscopy and Scattering: catalyst atomic structure and particle size Specialized ... Models Long-term durability testing X-ray tomography Optimize water and thermal ...

  20. Green Launching Pad Taps Six More Companies for Take-off | Department...

    Broader source: Energy.gov (indexed) [DOE]

    Brett Humble New Hampshire State Energy Program Project Officer Yesterday, U.S. Secretary of Energy Steven Chu joined New Hampshire Governor John Lynch and University of New ...

  1. Solar Decathlon Entry Uses iPad to Monitor Home | Department...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Relations Specialist, Office of Energy Efficiency & Renewable Energy How can I participate? ... Addthis Related Articles Team Austria of the Vienna Institute of Technology created an ...

  2. Nissan: ISO 50001 - What Counts! | Department of Energy

    Energy Savers [EERE]

    Nick Sinai About Us Nick Sinai - U.S. Deputy Chief Technology Officer, White House Office of Science and Technology Policy Nick Sinai is the U.S. Deputy CTO, White House Office of Science and Technology Policy and the former Energy and Environment Director for the Federal Communications Commission. Most Recent Expanded "Green Button" Will Reach Federal Agencies and More American Energy Consumers December 6 Green Button: Enabling Energy Innovation May 9 Better Building Federal Award

  3. When DNA Needs to Stand Up and Be Counted

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    scientists. Schematic of DNA structures in various conformations on a gold surface. Differences in overall structure and orientation are emphasized by color-coding of DNA...

  4. Abbreviated Total-Count Logging Procedures for Use in Remedial...

    Broader source: Energy.gov (indexed) [DOE]

    More Documents & Publications Field Calibration Facilities for Environmental Measurement of Radium, Thorium, and Potassium (October 2013) Gamma Survey of a Permeable Reactive ...

  5. Development of the SRS environmental counting laboratory gamma spectroscopy system

    SciTech Connect (OSTI)

    Filler, D.A.; Crandall, B.S.

    1996-12-31

    The Savannah River Site (SRS), one of several U.S. Department of Energy (DOE) facilities, produces nuclear materials for national defense and for other government and civilian uses. SRS ceased production of defense materials in 1988, and the site`s main activities now involve waste management and environmental restoration. These programs have generated extensive effluent monitoring and environmental surveillance programs for the Environmental Monitoring Section (EMS), which performs {approximately}105,000 radiological analyses on 30,000 samples a year. Gamma spectroscopy is performed on an estimated 10,000 samples annually. This report describes a program to develop and improve the EMS system.

  6. A New Shallow Underground Gas-Proportional Counting Lab - First...

    Office of Scientific and Technical Information (OSTI)

    obtain a copy of this journal article from the publisher. Find in Google Scholar Find in Google Scholar Search WorldCat Search WorldCat to find libraries that may hold this journal

  7. Particle Energy Spectrum, Revisited from a Counting Statistics Perspective

    SciTech Connect (OSTI)

    Yuan, D., Marks, D. G., Guss, P. P.

    2012-07-16

    This document is a slide show type presentation of a new covariance estimation for gamma spectra and neutron cross section.

  8. When DNA Needs to Stand Up and Be Counted

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Understanding both the attachment and orientation of DNA on gold surfaces was the goal of ... Schematic of DNA structures in various conformations on a gold surface. Differences in ...

  9. User:Nlangle/CategoryCounts | Open Energy Information

    Open Energy Info (EERE)

    Financial Organizations Total 138 Networking Organizations Total 98 Oil and Gas Total 23 Policy Organizations Total 123 Research Institutions Total 200 Govt Agencies Total 273...

  10. Maximum U.S. Active Seismic Crew Counts

    Gasoline and Diesel Fuel Update (EIA)

    Less electricity use this summer slightly offset by higher power costs The average U.S. household will use less electricity this summer than last summer because of expected cooler temperatures, but slightly higher electricity prices means summer power bills won't go down much. However, the outlook does vary across regions. Households in the South Atlantic states which includes Florida, Georgia, North Carolina, and Virginia will see the biggest savings. The average power bill in that region is

  11. Saving Energy in Altoona Where it Counts: City Lights | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    gives Altoona a much brighter appearance when the sun goes down.The city of Altoona, Pa. can trace 85 percent of its energy costs back to one area: lights. "Downtown sure looks ...

  12. Maximum U.S. Active Seismic Crew Counts

    Gasoline and Diesel Fuel Update (EIA)

    Marine Fuel Choice for Ocean- Going Vessels within Emissions Control Areas June 2015 Independent Statistics & Analysis www.eia.gov U.S. Department of Energy Washington, DC 20585 U.S. Energy Information Administration | Marine fuel choice for ocean going vessels within emissions control areas i This report was prepared by the U.S. Energy Information Administration (EIA), the statistical and analytical agency within the U.S. Department of Energy. By law, EIA's data, analyses, and forecasts are

  13. When DNA Needs to Stand Up and Be Counted

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DNA microarrays are small metal, glass, or silicon chips covered with patterns of short single-stranded DNA (ssDNA). These "DNA chips" are revolutionizing biotechnology, allowing ...

  14. 20,000 and Counting: Alternative Fueling and Charging Stations...

    Broader source: Energy.gov (indexed) [DOE]

    In addition, Clean Cities partners with a number of charging networks, including Blink and ChargePoint, to have their stations provide a daily feed to the Station Locator. This ...

  15. Counting small RNA in disease-causing organisms

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Counterterrorism A snapshot of NNSA's counterterrorism mission NNSA's mission of counterterrorism and counterproliferation is supported through innovative science and technology. Recently, Associate Administrator and Deputy Undersecretary for Counterterrorism and Counterproliferation Jay Tilden visited Oak Ridge National Laboratory (ORNL) and met with... Tilden appointed as Associate Administrator of Counterterrorism and Counterproliferation We are delighted to announce two key personnel

  16. CORRECTIVE ACTION PLAN FOR CORRECTIVE ACTION UNIT 224: DECON PAD AND SEPTIC SYSTEMS NEVADA TEST SITE, NEVADA

    SciTech Connect (OSTI)

    2006-07-01

    The purpose of this Corrective Action Plan is to provide the detailed scope of work required to implement the recommended corrective actions as specified in the approved CAU 224 CADD.

  17. untitled

    Gasoline and Diesel Fuel Update (EIA)

    Natural Gas Plant Net Production and Stocks of Petroleum Products by PAD and Refining Districts, 2014 (Thousand Barrels) Commodity Production PAD District 1 - East Coast PAD ...

  18. TABLE35.CHP:Corel VENTURA

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    ... Table 35. Net Movements of Crude Oil and Petroleum Products by Pipeline, Tanker, and Barge Between PAD Districts, PAD District I PAD District II Commodity Receipts Shipments Net ...

  19. TABLE14.CHP:Corel VENTURA

    Gasoline and Diesel Fuel Update (EIA)

    4. Production of Crude Oil by PAD District and State, January 1998 PAD District and State Total Daily Average (Thousand Barrels) PAD District I ......

  20. Microsoft Word - beam characterization and verification.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Beam Characterization and Verification Detector Components and Arrangement The beam uniformity and flux are determined using an array of five particle detectors. Each detector consists of Bicron BC-400 scintillator, a Bicron BC-634A optical coupling pad, a Hamamatsu R1635 photomultiplier tube, and a Hamamatsu E1761-04 tube base. Four of the detectors are fixed in position as show in Figure 1 and set up to measure beam particle counting rates continuously at four characteristic points, each 1.64

  1. Grade Assignments for Models Used for Calibration of Gross-Count...

    Broader source: Energy.gov (indexed) [DOE]

    Logging Methods for Exploration and Evaluation of Uranium Deposits (1967) Field Calibration Facilities for Environmental Measurement of Radium, Thorium, and Potassium (October 2013

  2. Point model equations for neutron correlation counting: Extension of Böhnel's equations to any order

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Favalli, Andrea; Croft, Stephen; Santi, Peter

    2015-06-15

    Various methods of autocorrelation neutron analysis may be used to extract information about a measurement item containing spontaneously fissioning material. The two predominant approaches being the time correlation analysis (that make use of a coincidence gate) methods of multiplicity shift register logic and Feynman sampling. The common feature is that the correlated nature of the pulse train can be described by a vector of reduced factorial multiplet rates. We call these singlets, doublets, triplets etc. Within the point reactor model the multiplet rates may be related to the properties of the item, the parameters of the detector, and basic nuclearmore » data constants by a series of coupled algebraic equations – the so called point model equations. Solving, or inverting, the point model equations using experimental calibration model parameters is how assays of unknown items is performed. Currently only the first three multiplets are routinely used. In this work we develop the point model equations to higher order multiplets using the probability generating functions approach combined with the general derivative chain rule, the so called Faà di Bruno Formula. Explicit expression up to 5th order are provided, as well the general iterative formula to calculate any order. This study represents the first necessary step towards determining if higher order multiplets can add value to nondestructive measurement practice for nuclear materials control and accountancy.« less

  3. ARM Research in the Equatorial Western Pacific: A Decade and Counting

    SciTech Connect (OSTI)

    Long, Charles N.; McFarlane, Sally A.; Del Genio, Anthony D.; Minnis, Patrick; Ackerman, Thomas P.; Mather, James H.; Comstock, Jennifer M.; Mace, Gerald G.; Jensen, Michael; Jakob, Christian

    2013-05-22

    The tropical western Pacific (TWP) is an important climatic region. Strong solar heating, warm sea surface temperatures and the annual progression of the Intertropical Convergence Zone (ITCZ) across this region generate abundant convective systems, which through their effects on the heat and water budgets have a profound impact on global climate and precipitation. To accurately represent tropical cloud systems in models, measurements of tropical clouds, the environment in which they reside, and their impact on the radiation and water budgets are needed. Because of the remote location, ground-based datasets of cloud, atmosphere, and radiation properties from the TWP region have traditionally come primarily from short-term field experiments. While providing extremely useful information on physical processes, these datasets are limited in statistical and climatological information because of their short duration. To provide long-term measurements of the surface radiation budget in the tropics, and the atmospheric properties that affect it, the Atmospheric Radiation Measurement program established a measurement site on Manus Island, Papua New Guinea in 1996 and on the island republic of Nauru in late 1998. These sites provide unique datasets available from more than 10 years of operation in the equatorial western Pacific on Manus and Nauru. We present examples of the scientific use of these datasets including characterization of cloud properties, analysis of cloud radiative forcing, model studies of tropical clouds and processes, and validation of satellite algorithms. We also note new instrumentation recently installed at the Manus site that will expand opportunities for tropical atmospheric science.

  4. U.S. Natural Gas Count of Underground Storage Capacity (Number...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 2013 413 412 417 419 419 419 419 419 419 419 419 419 2014 418 418 418 418 418 418 418 418 418 418 418 418 2015 418 417 417 417...

  5. Configurable memory system and method for providing atomic counting operations in a memory device

    DOE Patents [OSTI]

    Bellofatto, Ralph E.; Gara, Alan G.; Giampapa, Mark E.; Ohmacht, Martin

    2010-09-14

    A memory system and method for providing atomic memory-based counter operations to operating systems and applications that make most efficient use of counter-backing memory and virtual and physical address space, while simplifying operating system memory management, and enabling the counter-backing memory to be used for purposes other than counter-backing storage when desired. The encoding and address decoding enabled by the invention provides all this functionality through a combination of software and hardware.

  6. Modeling the Number of Ignitions Following an Earthquake: Developing Prediction Limits for Overdispersed Count Data

    Office of Environmental Management (EM)

    December 3, 2015 Mr. William Johnson President Mission Support Alliance, LLC 2490 Garlick Boulevard P.O. Box 650 Richland, Washington 99352 WEL-2015-07 Dear Mr. Johnson: The Office of Enterprise Assessments' Office of Enforcement has completed an evaluation of an incident involving a rigger injured during a crane re-spooling operation, as reported into the Department of Energy's (DOE) Occurrence Reporting and Processing System under EM-RL--MSC-FSS-2015-0002 on May 11, 2015. On May 1, 2015, a

  7. Opportunities for Decay Counting of Environmental Radioisotopes Using Ultra-low-background Detection Systems

    SciTech Connect (OSTI)

    Runkle, Robert C.; Aalseth, Craig E.; Bailey, Vanessa L.; Bonicalzi, Ricco; Moran, James J.; Seifert, Allen; Warren, Glen A.

    2012-08-01

    Executive Summary We present results from a scoping study whose intent was to define challenge measurements to be pursued on the Ultra-Sensitive Nuclear Measurements Initiative. Potential challenge measurements using new radiation detection technology in the shallow underground laboratory that would have substantial impact in environmental science were the focus of this study.

  8. Radon monitoring and early low background counting at the Sanford Underground Laboratory

    SciTech Connect (OSTI)

    Thomas, K.J.; Mei, D.M.; Heise, J.; Durben, D.; Salve, R.

    2010-09-01

    Radon detectors have been deployed underground at the Sanford Underground Laboratory at the site of the former Homestake Mine in Lead, SD. Currently, no radon mitigation measures are in place in the underground environment, and the continuing evolution of the facility ventilation systems has led to significant variations in early airborne radon concentrations. The average radon concentration measured near the primary ventilation intake for the 4850-ft level (Yates shaft) is 391 Bq/m{sup 3}, based on approximately 146 days of data. The corresponding average radon concentration near the other main ventilation intake for the 4850-ft level (Ross shaft) is 440 Bq/m{sup 3} based on approximately 350 days of data. Measurements have also been collected near the 1250-ft level Ross shaft, with average radon concentrations at 180 Bq/m{sup 3}. Secondary factors that may increase the baseline radon level underground include the presence of iron oxide and moisture, which are known to enhance radon emanation. The results of the current radon monitoring program will be used for the planning of future measurements and any potential optimization of ventilation parameters for the reduction of radon in relevant areas underground.

  9. Property:Geothermal/ProjectTypeTopic2Count | Open Energy Information

    Open Energy Info (EERE)

    + 0 + Geothermal Data Development, Collection, and Maintenance + 0 + Geothermal Energy Production from Low Temperature Resources, Coproduced Fluids from Oil and Gas Wells, and...

  10. Measurement of radionuclides using ion chromatography and flow-cell scintillation counting with pulse shape discrimination

    SciTech Connect (OSTI)

    DeVol, T.A.; Fjeld, R.A.

    1995-10-01

    The use of ion chromatography (IC) for radiochemical separations is a well established technique. IC is commonly used in routine environmental monitoring applications as well as in specialized research applications. Typical usage involves the separation of a single radionuclide from the non-radioactive constituents. During the past decade, a limited amount of research has been conducted using automated IC systems in actinide separation applications (e.g.). More recently, separation procedures for common non-gamma emitting activation and fission products were developed utilizing a high performance liquid chromatography (HPLC) system. In addition, a separation procedure for six common actinides has been developed using a HPLC system. These latter systems used on-line flow-cell detectors for quantification of the radioactive constituents of the effluent stream.

  11. Point model equations for neutron correlation counting: Extension of Böhnel's equations to any order

    SciTech Connect (OSTI)

    Favalli, Andrea; Croft, Stephen; Santi, Peter

    2015-06-15

    Various methods of autocorrelation neutron analysis may be used to extract information about a measurement item containing spontaneously fissioning material. The two predominant approaches being the time correlation analysis (that make use of a coincidence gate) methods of multiplicity shift register logic and Feynman sampling. The common feature is that the correlated nature of the pulse train can be described by a vector of reduced factorial multiplet rates. We call these singlets, doublets, triplets etc. Within the point reactor model the multiplet rates may be related to the properties of the item, the parameters of the detector, and basic nuclear data constants by a series of coupled algebraic equations – the so called point model equations. Solving, or inverting, the point model equations using experimental calibration model parameters is how assays of unknown items is performed. Currently only the first three multiplets are routinely used. In this work we develop the point model equations to higher order multiplets using the probability generating functions approach combined with the general derivative chain rule, the so called Faà di Bruno Formula. Explicit expression up to 5th order are provided, as well the general iterative formula to calculate any order. This study represents the first necessary step towards determining if higher order multiplets can add value to nondestructive measurement practice for nuclear materials control and accountancy.

  12. 20,000 and Counting: Alternative Fueling and Charging Stations Hit Major

    Broader source: Energy.gov (indexed) [DOE]

    Energy 179D commercial buildings energy efficiency tax deduction primarily enables building owners to claim a tax deduction for installing qualifying systems and buildings. Tenants may be eligible if they make construction expenditures. If the system or building is installed on federal, state, or local government property, the 179D tax deduction may be taken by the person primarily responsible for the system's design. The systems and buildings must have been placed in service by December 31,

  13. Counting Jobs and Economic Impacts from Distributed Wind in the United States (Poster)

    SciTech Connect (OSTI)

    Tegen, S.

    2014-05-01

    This conference poster describes the distributed wind Jobs and Economic Development Imapcts (JEDI) model. The goal of this work is to provide a model that estimates jobs and other economic effects associated with the domestic distributed wind industry. The distributed wind JEDI model is a free input-output model that estimates employment and other impacts resulting from an investment in distributed wind installations. Default inputs are from installers and industry experts and are based on existing projects. User input can be minimal (use defaults) or very detailed for more precise results. JEDI can help evaluate potential scenarios, current or future; inform stakeholders and decision-makers; assist businesses in evaluating economic development impacts and estimating jobs; assist government organizations with planning and evaluating and developing communities.

  14. Let us count the ways. We've built programs that reflect

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    We develop computational tools, algorithms and strategies to analyze, understand, create, design and build complex engineered, natural or human systems. Contact Mark Bryden,...

  15. Function point count adjustment by means of scaling touched function points

    SciTech Connect (OSTI)

    Bell, M.

    1997-11-01

    This report contains viewgraphs on the use of scaling touched function points to adjust function point analysis in determine the usefullness, productivity, and quality of software.

  16. Powered by NERSC, a Database of Billions of Genes and Counting...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    analysis of microbial communities sequenced by the ... With computing and storage support from the National Energy ... and Metagenome Super Program, the number and size of ...

  17. Learning How to Count: A High Multiplicity Search for the LHC...

    Office of Scientific and Technical Information (OSTI)

    ; Princeton, Inst. Advanced Study ; Jankowiak, Martin ; U. Heidelberg, ITP ; Wacker, Jay G. ; SLAC ; , Publication Date: 2014-05-01 OSTI Identifier: 1130358 Report Number(s):...

  18. Observed galaxy number counts on the lightcone up to second order: II. Derivation

    SciTech Connect (OSTI)

    Bertacca, Daniele; Maartens, Roy; Clarkson, Chris E-mail: roy.maartens@gmail.com

    2014-11-01

    We present a detailed derivation of the observed galaxy number over-density on cosmological scales up to second order in perturbation theory. We include all relativistic effects that arise from observing on the past lightcone. The derivation is in a general gauge, and applies to all dark energy models (including interacting dark energy) and to metric theories of modified gravity. The result will be important for accurate cosmological parameter estimation, including non-Gaussianity, since all projection effects need to be taken into account. It also offers the potential for new probes of General Relativity, dark energy and modified gravity. This paper accompanies Paper I which presents the key results for the concordance model in Poisson gauge.

  19. Observed galaxy number counts on the lightcone up to second order: I. Main result

    SciTech Connect (OSTI)

    Bertacca, Daniele; Maartens, Roy; Clarkson, Chris E-mail: roy.maartens@gmail.com

    2014-09-01

    We present the galaxy number overdensity up to second order in redshift space on cosmological scales for a concordance model. The result contains all general relativistic effects up to second order that arise from observing on the past light cone, including all redshift effects, lensing distortions from convergence and shear, and contributions from velocities, Sachs-Wolfe, integrated SW and time-delay terms. This result will be important for accurate calculation of the bias on estimates of non-Gaussianity and on precision parameter estimates, introduced by nonlinear projection effects.

  20. Development of Counted Single Donor Devices using in-situ Single...

    Office of Scientific and Technical Information (OSTI)

    Large gain Gain meaningless (digital signal) Single Ion Detection in Geiger ... far) GM ->high gain but provides digital signal (ion strike or no ion strike) ...

  1. U.S. Natural Gas Count of Underground Storage Capacity (Number of Elements)

    U.S. Energy Information Administration (EIA) Indexed Site

    Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1980's 394 1990's 392 387 388 389 397 403 406 418 410 413 2000's 413 418 407 391 393 394 397 400 401 409 2010's 411 410 414 419 418

  2. U.S. Natural Gas Count of Underground Storage Capacity (Number of Elements)

    U.S. Energy Information Administration (EIA) Indexed Site

    Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 2013 413 412 417 419 419 419 419 419 419 419 419 419 2014 418 418 418 418 418 418 418 418 418 418 418 418 2015 418 417 417 417 413 413 413 413 413 413 413 413 2016 413 413 413 413 415 415

  3. QUASAR-GALAXY CLUSTERING THROUGH PROJECTED GALAXY COUNTS AT z = 0.6-1.2

    SciTech Connect (OSTI)

    Zhang Shaohua; Zhou Hongyan; Wang Tinggui; Wang Huiyuan E-mail: twang@ustc.edu.cn

    2013-08-20

    We investigate the spatial clustering of galaxies around quasars at z = 0.6-1.2 using photometric data from Sloan Digital Sky Survey Stripe 82. The quasar and galaxy cross-correlation functions are measured through the projected galaxy number density n(r{sub p} ) on scales of 0.05 < r{sub p} < 20 h {sup -1} Mpc around quasars for a sample of 2300 quasars from Schneider et al. We detect strong clustering signals at all redshifts and find that the clustering amplitude increases significantly with redshift. We examine the dependence of quasar-galaxy clustering on quasar and galaxy properties and find that the clustering amplitude is significantly larger for quasars with more massive black holes or with bluer colors, while there is no dependence on quasar luminosity. We also show that quasars have a stronger correlation amplitude with blue galaxies than with red galaxies. We finally discuss the implications of our findings.

  4. Recovery of Depleted Uranium Fragments from Soil

    SciTech Connect (OSTI)

    Farr, C.P.; Alecksen, T.J.; Heronimus, R.S.; Simonds, M.H.; Farrar, D.R.; Baker, K.R.; Miller, M.L.

    2008-07-01

    A cost-effective method was demonstrated for recovering depleted uranium (DU) fragments from soil. A compacted clean soil pad was prepared adjacent to a pile of soil containing DU fragments. Soil from the contaminated pile was placed on the pad in three-inch lifts using conventional construction equipment. Each lift was scanned with an automatic scanning system consisting of an array of radiation detectors coupled to a detector positioning system. The data were downloaded into ArcGIS for data presentation. Areas of the pad exhibiting scaler counts above the decision level were identified as likely locations of DU fragments. The coordinates of these locations were downloaded into a PDA that was wirelessly connected to the positioning system. The PDA guided technicians to the locations where hand-held trowels and shovels were used to remove the fragments. After DU removal, the affected areas were re-scanned and the new data patched into the data base to replace the original data. This new data set along with soil sample results served as final status survey data. (authors)

  5. Resolution of Surveillance Report No. PAD-BDW-95-004 for suspect bolts installed in the 105 KW roof addition structure

    SciTech Connect (OSTI)

    Frier, W.A.

    1995-04-14

    A DOE RL surveillance determined that a test report (WHC-SD-NR-TRP-020) was less than adequate. As a result, WHC removed nine of the previous in-situ tested A325 suspect bolts and contracted with Koon-Hall Testing Corporation to perform hardness and tensile testing and chemical composition analysis of the removed bolts. WHC also contracted with ADVENT Engineering, Inc., to perform an evaluation of the Koon-Hall test results and to respond to the concerns identified in the DOE RL surveillance. The Koon-Hall Laboratory test results and the assessments strongly support the conclusion that the suspect bolts are indeed the equivalent of A325 high-strength, Type-1 bolts and have been properly heat-treated.

  6. Energy Information Administration/Petroleum Marketing Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    5 0 20 40 60 80 100 120 140 J F M A M J J A S O N D 1999 Cents per Gallon Excluding Taxes PAD District I PAD District II PAD District III PAD District IV PAD District V Figure 6....

  7. Energy Information Administration/Petroleum Marketing Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    5 0 20 40 60 80 100 120 J F M A M J J A S O N D 1998 Cents per Gallon Excluding Taxes PAD District I PAD District II PAD District III PAD District IV PAD District V Figure 6. U.S....

  8. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    0 50 100 150 200 250 300 J F M A M J J A S O N D 2005 Cents per Gallon Excluding Taxes PAD District I PAD District II PAD District III PAD District IV PAD District V Figure 6....

  9. X:\\L6046\\Data_Publication\\Pma\\current\\ventura\\pma.vp

    U.S. Energy Information Administration (EIA) Indexed Site

    5 0 20 40 60 80 100 120 140 160 180 J F M A M J J A S O N D 2001 Cents per Gallon Excluding Taxes PAD District I PAD District II PAD District III PAD District IV PAD District V...

  10. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    3 110 140 170 200 230 260 290 320 350 J F M A M J J A S O N D 2009 Cents per Gallon Excluding Taxes PAD District I PAD District II PAD District III PAD District IV PAD District V...

  11. X:\\L6046\\Data_Publication\\Pma\\current\\ventura\\pma.vp

    U.S. Energy Information Administration (EIA) Indexed Site

    5 0 20 40 60 80 100 120 140 160 180 J F M A M J J A S O N D 2003 Cents per Gallon Excluding Taxes PAD District I PAD District II PAD District III PAD District IV PAD District V...

  12. X:\\L6046\\Data_Publication\\Pma\\current\\ventura\\pma.vp

    U.S. Energy Information Administration (EIA) Indexed Site

    0 50 100 150 200 250 J F M A M J J A S O N D 2004 Cents per Gallon Excluding Taxes PAD District I PAD District II PAD District III PAD District IV PAD District V Figure 6. U.S....

  13. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    0 50 100 150 200 250 300 J F M A M J J A S O N D 2006 Cents per Gallon Excluding Taxes PAD District I PAD District II PAD District III PAD District IV PAD District V Figure 6....

  14. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    3 210 230 250 270 290 310 330 J F M A M J J A S O N D 2007 Cents per Gallon Excluding Taxes PAD District I PAD District II PAD District III PAD District IV PAD District V Figure 6....

  15. X:\\L6046\\Data_Publication\\Pma\\current\\ventura\\pma.vp

    U.S. Energy Information Administration (EIA) Indexed Site

    5 0 20 40 60 80 100 120 140 J F M A M J J A S O N D 2002 Cents per Gallon Excluding Taxes PAD District I PAD District II PAD District III PAD District IV PAD District V Figure 6....

  16. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    3 190 220 250 280 310 340 370 400 430 460 J F M A M J J A S O N D 2008 Cents per Gallon Excluding Taxes PAD District I PAD District II PAD District III PAD District IV PAD District...

  17. X:\\Data_Publication\\Pma\\current\\ventura\\pma00.vp

    U.S. Energy Information Administration (EIA) Indexed Site

    5 0 20 40 60 80 100 120 140 160 180 J F M A M J J A S O N D 2000 Cents per Gallon Excluding Taxes PAD District I PAD District II PAD District III PAD District IV PAD District V...

  18. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    9 Table 1A. Refiner Acquisition Cost of Crude Oil by PAD Districts (Dollars per Barrel) Year Month U.S. PAD District 1 PAD District 2 Domestic Imported Composite Domestic Imported...

  19. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    8 Table 1A. Refiner Acquisition Cost of Crude Oil by PAD Districts (Dollars per Barrel) Year Month U.S. PAD District 1 PAD District 2 Domestic Imported Composite Domestic Imported...

  20. TABLE14.CHP:Corel VENTURA

    Gasoline and Diesel Fuel Update (EIA)

    4. Production of Crude Oil by PAD District and State, January 1998 PAD District and State Total Daily Average (Thousand Barrels) PAD District I .......................................................................................... 824 27 Florida ................................................................................................. 523 17 New York ............................................................................................. 19 1 Pennsylvania

  1. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    Information AdministrationPetroleum Marketing Annual 2005 4 Table 1A. Refiner Acquisition Cost of Crude Oil by PAD Districts (Dollars per Barrel) - Continued Year Month PAD...

  2. Prime Contracts - Hanford Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Size To search the Procurement and Assistance Data System (PADS) for DOE awards via the web, go to PADS Online. Major Prime Contracts Computer Sciences Corporation (CSC) -...

  3. Geographic Area Month Sales to End Users Sales

    U.S. Energy Information Administration (EIA) Indexed Site

    Prices by Sales Type and PAD District Energy Information Administration Petroleum Marketing Annual 1997 221 Table 38. Propane (Consumer Grade) Prices by Sales Type and PAD...

  4. Geographic Area Month Sales to End Users Sales

    U.S. Energy Information Administration (EIA) Indexed Site

    Prices by Sales Type and PAD District Energy Information Administration Petroleum Marketing Annual 1996 221 Table 38. Propane (Consumer Grade) Prices by Sales Type and PAD...

  5. untitled

    Gasoline and Diesel Fuel Update (EIA)

    Residual Fuel Oil Prices by PAD District and State (Cents per Gallon Excluding Taxes) ... Annual 2009 201 Table 38. Residual Fuel Oil Prices by PAD District and State ...

  6. Total neutron-counting plutonium inventory measurement systems (PIMS) and their potential application to near real time materials accountancy (NRTMA)

    SciTech Connect (OSTI)

    Driscall, I.; Fox, G.H.; Orr, C.H.; Whitehouse, K.R. , Sellafield )

    1988-07-01

    A radiometric method of determining the inventory of an operating plutonium plant is described. An array of total neutron counters distributed across the plant is used to estimate hold-up at each plant item. Corrections for the sensitivity of detectors to plutonium in adjacent plant items are achieved through a matrix approach. This paper describes our experience in design, calibration and operation of a Plutonium Inventory Measurement System (PIMS) on an oxalate precipitation plutonium finishing line. Data from a recent trial of Near-Real-Time Materials Accounting (NRTMA) using the PIMS are presented and used to illustrate its present performance and problem areas. The reader is asked to consider what role PIMS might have in future accountancy systems.

  7. Use of the HPI Model 2080 pulsed neutron detector at the LANSCE complex - vulnerabilities and counting statistics

    SciTech Connect (OSTI)

    Jones, K.W.; Browman, A.

    1997-01-01

    The BPI Model 2080 Pulsed Neutron Detector has been used for over seven years as an area radiation monitor and dose limiter at the LANSCE accelerator complex. Operating experience and changing environments over this time have revealed several vulnerabilities (susceptibility to electrical noise, paralysis in high dose rate fields, etc.). Identified vulnerabilities have been connected; these modifications include component replacement and circuit design changes. The data and experiments leading to these modifications will be presented and discussed. Calibration of the instrument is performed in mixed static gamma and neutron source fields. The statistical characteristics of the Geiger-Muller tubes coupled with significantly different sensitivity to gamma and neutron doses require that careful attention be paid to acceptable fluctuations in dose rate over time during calibration. The performance of the instrument has been modeled using simple Poisson statistics and the operating characteristics of the Geiger-Muller tubes. The results are in excellent agreement with measurements. The analysis and comparison with experimental data will be presented.

  8. Identifying messaging completion in a parallel computer by checking for change in message received and transmitted count at each node

    DOE Patents [OSTI]

    Archer, Charles J.; Hardwick, Camesha R.; McCarthy, Patrick J.; Wallenfelt, Brian P.

    2009-06-23

    Methods, parallel computers, and products are provided for identifying messaging completion on a parallel computer. The parallel computer includes a plurality of compute nodes, the compute nodes coupled for data communications by at least two independent data communications networks including a binary tree data communications network optimal for collective operations that organizes the nodes as a tree and a torus data communications network optimal for point to point operations that organizes the nodes as a torus. Embodiments include reading all counters at each node of the torus data communications network; calculating at each node a current node value in dependence upon the values read from the counters at each node; and determining for all nodes whether the current node value for each node is the same as a previously calculated node value for each node. If the current node is the same as the previously calculated node value for all nodes of the torus data communications network, embodiments include determining that messaging is complete and if the current node is not the same as the previously calculated node value for all nodes of the torus data communications network, embodiments include determining that messaging is currently incomplete.

  9. The Use of Isotope Dilution Alpha Spectrometry and Liquid Scintillation Counting to Determine Radionuclides in Environmental Samples

    SciTech Connect (OSTI)

    Bylyku, Elida

    2009-04-19

    In Albania in recent years it has been of increasing interest to determine various pollutants in the environment and their possible effects on human health. The radiochemical procedure used to identify Pu, Am, U, Th, and Sr radioisotopes in soil, sediment, water, coal, and milk samples is described. The analysis is carried out in the presence of respective tracer solutions and combines the procedure for Pu analysis based on anion exchange, the selective method for Sr isolation based on extraction chromatography using Sr-Spec resin, and the application of the TRU-Spec column for separation of Am fraction. An acid digestion method has been applied for the decomposition of samples. The radiochemical procedure involves the separation of Pu from Th, Am, and Sr by anion exchange, followed by the preconcentration of Am and Sr by coprecipitation with calcium oxalate. Am is separated from Sr by extraction chromatography. Uranium is separated from the bulk elements by liquid-liquid extraction using UTEVA registered resin. Thin sources for alpha spectrometric measurements are prepared by microprecipitation with NdF3. Two International Atomic Energy Agency reference materials were analyzed in parallel with the samples.

  10. Low-Intrusion Techniques and Sensitive Information Management for Warhead Counting and Verification: FY2012 Annual Report

    SciTech Connect (OSTI)

    Jarman, Kenneth D.; McDonald, Benjamin S.; Robinson, Sean M.; Gilbert, Andrew J.; White, Timothy A.; Pitts, W. Karl; Misner, Alex C.; Seifert, Allen

    2012-11-01

    Progress in the second year of this project is described by the series of technical reports and manuscripts that make up the content of this report. These documents summarize successes in our goals to develop our robust image-hash templating and material-discrimination techniques and apply them to test image data.

  11. Determination of the 235U Mass and Enrichment within Small UF6 Cylinders via a Neutron Coincidence Well Counting System

    SciTech Connect (OSTI)

    McElroy, Robert Dennis; Croft, Dr. Stephen; Young, Brian M; Venkataraman, Ram

    2011-01-01

    The construction of three new uranium enrichment facilities in the United States has sparked renewed interest in the development and enhancement of methods to determine the enrichment and fissile mass content of UF6 cylinders. We describe the design and examine the expected performance of a UF6 bottle counter developed for the assay of Type 5A cylinders. The counter, as designed and subsequently constructed, is a tall passive neutron well counter with a clam-shell configuration and graphite end plugs operated in fast neutron mode. Factory performance against expectation is described. The relatively high detection efficiency and effectively 4 detection geometry provide a near-ideal measurement configuration, making the UF6 bottle counter a valuable tool for the evaluation of the neutron coincidence approach to UF6 cylinder assay. The impacts of non-uniform filling, voids, enrichment, and mixed enrichments are examined

  12. Five-element Johann-type x-ray emission spectrometer with a single-photon-counting pixel detector

    SciTech Connect (OSTI)

    Kleymenov, Evgeny; Bokhoven, Jeroen A. van; David, Christian; Janousch, Markus; Studer, Marco; Willimann, Markus; Bergamaschi, Anna; Henrich, Beat; Nachtegaal, Maarten; Glatzel, Pieter; Alonso-Mori, Roberto

    2011-06-15

    A Johann-type spectrometer with five spherically bent crystals and a pixel detector was constructed for a range of hard x-ray photon-in photon-out synchrotron techniques, covering a Bragg-angle range of 60 deg. - 88 deg. The spectrometer provides a sub emission line width energy resolution from sub-eV to a few eV and precise energy calibration, better than 1.5 eV for the full range of Bragg angles. The use of a pixel detector allows fast and easy optimization of the signal-to-background ratio. A concentration detection limit below 0.4 wt% was reached at the Cu K{alpha}{sub 1} line. The spectrometer is designed as a modular mobile device for easy integration in a multi-purpose hard x-ray synchrotron beamline, such as the SuperXAS beamline at the Swiss Light Source.

  13. Operation Greenhouse. Scientific Director's report of atomic weapon tests at Eniwetok, 1951. Annex 6. 6. Evaluation of filter material

    SciTech Connect (OSTI)

    Engquist, E,H.

    1985-04-01

    Four types of standard and developmental filter materials used in individual and collective-protective devices and one type of developmental filter material used for sampling of air for particulate matter were evaluated against the contamination produced by the detonation of an atomic bomb and present in the resulting radioactive cloud. These filter materials were evaluated in multilayer pads at the standard flow-rate conditions used by the Chemical Corps in evaluation studies of filter materials. This permitted correlation of results of laboratory data. Analysis of the materials was made by counting the gross beta activity collected on successive layers of the same filter material and the efficiency of the materials was calculated from the data obtained.

  14. Weekly Petroleum Status Report

    U.S. Energy Information Administration (EIA) Indexed Site

    Crude Stocks Figure 1. Stocks of Crude Oil by PAD District, January 2015 to Present

  15. X:\\L6046\\Data_Publication\\Pma\\current\\ventura\\pma.vp

    U.S. Energy Information Administration (EIA) Indexed Site

    and Residual Fuel Oils, by PAD District, 1983-Present . . . . . . . . . . 439 Figures 1. Crude Oil Prices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  16. --No Title--

    U.S. Energy Information Administration (EIA) Indexed Site

    Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon Excluding Taxes) - Continued ...

  17. --No Title--

    U.S. Energy Information Administration (EIA) Indexed Site

    Fuels, Propane, and Kerosene, by PAD District, 1983-Present (Cents per Gallon Excluding Taxes) - Continued ...

  18. --No Title--

    U.S. Energy Information Administration (EIA) Indexed Site

    and Residual Fuel Oils, by PAD District, 1983-Present (Cents per Gallon Excluding Taxes) - Continued ...

  19. Launching Green Entrepreneurship in New Hampshire

    Broader source: Energy.gov [DOE]

    Green Launching Pad initiative accelerates funding and expertise to grow environmentally-oriented businesses.

  20. --No Title--

    U.S. Energy Information Administration (EIA) Indexed Site

    || | ct II | PAD | | | | | | Year |(Conti-|Distri-| | | | | | Month | nued) | ct III| | | | | | ||Average|Average| ID...

  1. U.S. Downstream Charge Capacity of Operable Petroleum Refineries

    U.S. Energy Information Administration (EIA) Indexed Site

    Day, Except Where Noted) Area: U.S. PAD District 1 Delaware Florida Georgia Maryland New Jersey New York North Carolina Pennsylvania Virginia West Virginia PAD District 2 Illinois Indiana Kansas Kentucky Michigan Minnesota Missouri Nebraska North Dakota Ohio Oklahoma Tennessee Wisconsin PAD District 3 Alabama Arkansas Louisiana Mississippi New Mexico Texas PAD District 4 Colorado Montana Utah Wyoming PAD District 5 Alaska Arizona California Hawaii Nevada Oregon Washington Guam Puerto Rico Virgin

  2. U.S. Production Capacity of Operable Petroleum Refineries

    U.S. Energy Information Administration (EIA) Indexed Site

    Day, Except Where Noted) Area: U.S. PAD District 1 Delaware Florida Georgia Maryland New Jersey New York North Carolina Pennsylvania Virginia West Virginia PAD District 2 Illinois Indiana Kansas Kentucky Michigan Minnesota Missouri Nebraska North Dakota Ohio Oklahoma Tennessee Wisconsin PAD District 3 Alabama Arkansas Louisiana Mississippi New Mexico Texas PAD District 4 Colorado Montana Utah Wyoming PAD District 5 Alaska Arizona California Hawaii Nevada Oregon Washington Guam Puerto Rico Virgin

  3. tracc.anl.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    About TRACC Article Count: 10 TRACC Article Count: 22 CFD Article Count: 24 CSM Article Count: 15 TRAFFIC Article Count: 49 Collaboration Article Count: 4 Computing Article Count: 4 TRANSPORTATION RESEARCH Article Count: 2 Polaris Article Count: 2 Blog Article Count: 1

  4. TABLE15.CHP:Corel VENTURA

    Gasoline and Diesel Fuel Update (EIA)

    5. Natural Gas Plant Net Production and Stocks of Petroleum Products by PAD and Refining PAD District I PAD District II Commodity East Appalachian Minn., Wis., Okla., Kans., Coast No. 1 Total Ind., Ill., Ky. N. Dak., S. Dak. Mo. Total Net Production Net Production Stocks Stocks Districts, (Thousand Barrels) PAD District III PAD Dist. PAD Dist. Commodity IV V Texas La. Texas Gulf Gulf N. La., New U.S. Inland Coast Coast Ark. Mexico Total Rocky Mt. West Coast Total January 1998 Natural Gas Liquids

  5. Method of fabricating a solar cell array

    DOE Patents [OSTI]

    Lazzery, Angelo G.; Crouthamel, Marvin S.; Coyle, Peter J.

    1982-01-01

    A first set of pre-tabbed solar cells are assembled in a predetermined array with at least part of each tab facing upward, each tab being fixed to a bonding pad on one cell and abutting a bonding pad on an adjacent cell. The cells are held in place with a first vacuum support. The array is then inverted onto a second vacuum support which holds the tabs firmly against the cell pads they abut. The cells are exposed to radiation to melt and reflow the solder pads for bonding the tab portions not already fixed to bonding pads to these pads.

  6. In situ object counting system (ISOCSi3T{sup M}) technique: A cost-effective tool for NDA verification in IAEA Safeguards

    SciTech Connect (OSTI)

    Nizhnik, V.; Belian, A.; Shephard, A.; Lebrun, A.

    2011-07-01

    Nuclear material measurements using the ISOCS technique are playing an increasing role in IAEA verification activities. The ISOCS capabilities include: a high sensitivity to the presence of U and Pu; the ability to detect very small amounts of material; and the ability to measure items of different shapes and sizes. In addition, the numerical absolute efficiency calibration of a germanium detector used in the technique does not require any calibration standards or reference materials. The ISOCS modelling software performs an absolute efficiency calibration for items with various container shapes, container wall materials, material compositions, material fill-heights, U/Pu weight fractions and even heterogeneously distributed emitting materials. In a number of cases, some key parameters, such as the matrix density and U/Pu weight fraction, can be determined in addition to the emitting material mass and isotopic composition. These capabilities provide a verification solution suitable for a majority of cases where quantitative and isotopic analysis should be performed. Taking into account these advantages, the technique becomes a cost-effective solution for nuclear material non-destructive assay (NDA) verification. At present, the IAEA uses the ISOCS for a wide range of applications including the quantitative analysis of U scrap materials, U/Pu contaminated solid wastes, U fuel elements, U hold-up materials. Additionally, the ISOCS is also applied to some specific verification cases such as the measurement of PuBe neutron sources and the quantification of fission products in solid wastes. In reprocessing facilities with U/Pu waste compaction or facilities with item re-batching, the continuity-of-knowledge can be assured by applying either video surveillance systems together with seals (requiring attaching/detaching and verification activities for each seal) or verification of operator declarations using quantitative measurements for items selected on a random basis. In some cases, the first option is too expensive and places a high demand on inspector and operator time. Quantitative NDA based on the ISOCS technique verifies these materials and significantly decreases the resources required for assuring the continuity-of-knowledge. (authors)

  7. Experiments and Simulations of the Use of Time-Correlated Thermal Neutron Counting to Determine the Multiplication of an Assembly of Highly Enriched Uranium

    SciTech Connect (OSTI)

    David L. Chichester; Mathew T. Kinlaw; Scott M. Watson; Jeffrey M. Kalter; Eric C. Miller; William A. Noonan

    2014-11-01

    A series of experiments and numerical simulations using thermal-neutron time-correlated measurements has been performed to determine the neutron multiplication, M, of assemblies of highly enriched uranium available at Idaho National Laboratory. The experiments used up to 14.4 kg of highly-enriched uranium, including bare assemblies and assemblies reflected with high-density polyethylene, carbon steel, and tungsten. A small 252Cf source was used to initiate fission chains within the assembly. Both the experiments and the simulations used 6-channel and 8-channel detector systems, each consisting of 3He proportional counters moderated with polyethylene; data was recorded in list mode for analysis. 'True' multiplication values for each assembly were empirically derived using basic neutron production and loss values determined through simulation. A total of one-hundred and sixteen separate measurements were performed using fifty-seven unique measurement scenarios, the multiplication varied from 1.75 to 10.90. This paper presents the results of these comparisons and discusses differences among the various cases.

  8. Webpage Data 2014-05-06 1230-RogerNelsonVersion_rfk.xlsx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    H-7 Pad (0-2 cm) 6132014 Below MDC Below MDC H-7 Pad (0-2 cm) (Duplicate) 6132014 Below MDC Below MDC GPS Location 01 (0-2 cm) 3192014 Below MDC Below MDC GPS Location 02...

  9. Refinery Capacity Report

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Storage Capacity at Operable Refineries by PAD District as of January 1, 2006 PDF 9 Shell Storage Capacity at Operable Refineries by PAD District as of January 1, 2006 PDF 10...

  10. TABLE26.CHP:Corel VENTURA

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    6. Imports of Residual Fuel Oil by Sulfur Content and by PAD District and State of Entry, ... Residual Fuel Oil PAD District and State of Entry Less than 0.31 to Greater 0.31% 1.00% ...

  11. Microsoft Word - S03965_FINAL 2014_PLF M&M Plan.docx

    Office of Legacy Management (LM)

    ... Casing, Sch 40-PVC, 2 in. ID. Hydrated Bentonite Pellets Concrete Seal Concrete Pad Filter ... Casing, Sch 40-PVC, 2 in. ID. Hydrated Bentonite Pellets Concrete Seal Concrete Pad ...

  12. Wharf site.sdr

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SACR ANT Cement Pad ECOR 75 Ft from water edge 10 ft from low wall Front of container ANT van not on cement pad 245 mtr PWR DROP in red, 245 meters from west lot line

  13. untitled

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Crude Oil Prices Table 18. Domestic Crude Oil First Purchase Prices (Dollars per Barrel) Year Month U.S. Average PAD District I PAD District II U.S. Average Less AK North Slope ...

  14. Pixel Array Detector for Time-Resolved X-ray Science, September 1, 1997 - September 14, 2000

    SciTech Connect (OSTI)

    Gruner, Sol M.

    2000-11-07

    Progress on the design, fabrication, testing and assembly of two-layer Pixel Array Detectors (PADs) is described. The PADs are developed for challenging time-resolved X-ray imaging applications at synchrotron radiation X-ray sources.

  15. Petroleum Supply Annual 1998, Volume 2

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    by Pipeline Between PAD Districts PDF TXT 34 Movements of Crude Oil and Petroleum Products by Tanker and Barge Between PAD Districts PDF TXT 35 Net Movements of Crude Oil ...

  16. Petroleum Supply Annual 1997, Volume 1

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    ... by Pipeline Between PAD Districts PDF TXT 34 Movements of Crude Oil and Petroleum Products by Tanker and Barge Between PAD Districts PDF TXT 35 Net Movements of Crude Oil ...

  17. Microsoft Word - DOE-ID-INL-13-011.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Emissions - Fugitive dust may be generated during the installation of a concrete pad or placement of a pre-formed concrete pad and drilling. Also minor amounts of dust will occur...

  18. Electrical interconnect

    DOE Patents [OSTI]

    Frost, John S.; Brandt, Randolph J.; Hebert, Peter; Al Taher, Omar

    2015-10-06

    An interconnect includes a first set of connector pads, a second set of connector pads, and a continuous central portion. A first plurality of legs extends at a first angle from the continuous central portion. Each leg of the first plurality of legs is connected to a connector pad of a first set of connector pads. A second plurality of legs extends at a second angle from the continuous central portion. Each leg of the second plurality of legs is connected to a connector pad of the second set of connector pads. Gaps are defined between legs. The gaps enable movement of the first set of connector pads relative to the second set of connector pads.

  19. PPPL data may play role in first NASA space probe dedicated to...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    data may play role in first NASA space probe dedicated to magnetic reconnection By Raphael ... to the launch pad. (Photo by NASA) The Atlas V MMS rocket is rolled out to the launch pad. ...

  20. A3.

    U.S. Energy Information Administration (EIA) Indexed Site

    A3. RefinerReseller Prices of Distillate and Residual Fuel Oils, by PAD District, 1983-Present Table A3. RefinerReseller Prices of Distillate and Residual Fuel Oils, by PAD...

  1. Record of Decision for the Electrical Interconnection of the...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... A pad to support a construction crane is included in this area. Overall, the construction of crane pads and tower foundations would impact about 10.7 acres. * Individual step-up ...

  2. untitled

    Gasoline and Diesel Fuel Update (EIA)

    No. 2 Diesel Fuel Prices by Sales Type, PAD District, and Selected States a (Cents per ... Annual 2009 Table 36. No. 2 Diesel Fuel Prices by Sales Type, PAD District, and ...

  3. Inspection tester for explosives

    DOE Patents [OSTI]

    Haas, Jeffrey S.; Simpson, Randall L.; Satcher, Joe H.

    2007-11-13

    An inspection tester that can be used anywhere as a primary screening tool by non-technical personnel to determine whether a surface contains explosives. It includes a body with a sample pad. First and second explosives detecting reagent holders and dispensers are operatively connected to the body and the sample pad. The first and second explosives detecting reagent holders and dispensers are positioned to deliver the explosives detecting reagents to the sample pad. A is heater operatively connected to the sample pad.

  4. Inspection tester for explosives

    DOE Patents [OSTI]

    Haas, Jeffrey S.; Simpson, Randall L.; Satcher, Joe H.

    2010-10-05

    An inspection tester that can be used anywhere as a primary screening tool by non-technical personnel to determine whether a surface contains explosives. It includes a body with a sample pad. First and second explosives detecting reagent holders and dispensers are operatively connected to the body and the sample pad. The first and second explosives detecting reagent holders and dispensers are positioned to deliver the explosives detecting reagents to the sample pad. A is heater operatively connected to the sample pad.

  5. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    Commodity Motor Gasoline Motor Gasoline Blending Components Kerosene Reformulated Conventional Total Reformulated Conventional Total PAD District 1 ......

  6. Weekly Petroleum Status Report

    U.S. Energy Information Administration (EIA) Indexed Site

    7 Mogas Stocks Figure 2. Stocks of Total Motor Gasoline by PAD District, January 2015 to Present

  7. Weekly Petroleum Status Report

    U.S. Energy Information Administration (EIA) Indexed Site

    9 Distillate Stocks Figure 3. Stocks of Distillate Fuel Oil by PAD District, January 2015 to Present

  8. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    0 June 2016 Table 62. Net Movements of Crude Oil and Petroleum Products by Pipeline, Tanker, Barge and Rail Between PAD Districts, June 2016 (Thousand Barrels) Commodity PAD District 1 PAD District 2 PAD District 3 Receipts Shipments Net Receipts Receipts Shipments Net Receipts Receipts Shipments Net Receipts Crude Oil 1 ................................................................ 5,854 111 5,743 41,510 44,952 -3,442 31,303 27,535 3,768 Petroleum Products 2

  9. --No Title--

    U.S. Energy Information Administration (EIA) Indexed Site

    Prices by Sales Type, PAD District, and Selected States(2) (Cents per Gallon Excluding Taxes) - Continued | | | Sales to End...

  10. Photovoltaic Films - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Solar Photovoltaic Solar Photovoltaic Find More Like This Return to Search Photovoltaic Films Los Alamos National Laboratory Contact LANL About This Technology LANL&rsquo;s solar power portfolio includes a deposition process known as PAD. PAD eliminates the need for vacuum-based thin film equipment. LANL's solar power portfolio includes a deposition process known as PAD. PAD eliminates the need for vacuum-based thin film equipment. Technology Marketing SummaryThe rising total cost of energy

  11. Sampling device with a capped body and detachable handle

    DOE Patents [OSTI]

    Jezek, Gerd-Rainer

    2000-01-01

    The apparatus is a sampling device having a pad for sample collection, a body which supports the pad, a detachable handle connected to the body and a cap which encloses and retains the pad and body to protect the integrity of the sample.

  12. J F M A M J J A S O N D

    U.S. Energy Information Administration (EIA) Indexed Site

    995 Cents per Gallon Excluding Taxes P AD Distric t I P AD Distric t II PAD Distric t III P AD Distric t IV PAD Distric t V 6. U.S. No. 2 Distillate Prices to Residences by PAD...

  13. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    4.PDF Table 14. Production of Crude Oil by PAD District and State, January 2014 (Thousand Barrels) PAD District and State January 2014 Total Daily Average PAD District 1 ...................................................... 1,408 45 Florida ............................................................... 182 6 New York .......................................................... 28 1 Pennsylvania .................................................... 550 18 Virginia

  14. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    0.PDF Table 20. Blender Net Inputs of Petroleum Products by PAD Districts, January 2014 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Natural Gas Plant Liquids and Liquefied Refinery Gases ....................................................... 358 2 360 69 38 259 366 Pentanes Plus

  15. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    1 June 2016 Table 26. Production of Crude Oil by PAD District and State, June 2016 (Thousand Barrels) PAD District and State June 2016 January-June 2016 Total Daily Average Total Daily Average PAD District 1 ...................................................... 1,348 45 8,472 47 Florida ............................................................... 158 5 995 5 New York .......................................................... 23 1 139 1 Pennsylvania

  16. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    1 June 2016 Table 32. Blender Net Inputs of Petroleum Products by PAD District, June 2016 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Natural Gas Plant Liquids and Liquefied Refinery Gases ....................................................... 21 - 21 - 10 85 95 Pentanes Plus

  17. PCR amplification on microarrays of gel immobilized oligonucleotides

    DOE Patents [OSTI]

    Strizhkov, Boris; Tillib, Sergei; Mikhailovich, Vladimir; Mirzabekov, Andrei

    2003-11-04

    The invention relates two general methods for performing PCR amplification, combined with the detection and analysis of the PCR products on a microchip. In the first method, the amplification occurs both outside and within a plurality of gel pads on a microchip, with at least one oligonucleotide primer immobilized in a gel pad. In the second method, PCR amplification also takes place within gel pads on a microchip, but the pads are surrounded by a hydrophobic liquid such as that which separates the individual gel pads into environments which resemble micro-miniaturized test tubes.

  18. Personal annunciation device

    SciTech Connect (OSTI)

    Angelo, Peter; Younkin, James; DeMint, Paul

    2011-01-25

    A personal annunciation device (PAD) providing, in an area of interest, compensatory annunciation of the presence of an abnormal condition in a hazardous area and accountability of the user of the PAD. Compensatory annunciation supplements primary annunciation provided by an emergency notification system (ENS). A detection system detects an abnormal condition, and a wireless transmission system transmits a wireless transmission to the PAD. The PAD has a housing enclosing the components of the PAD including a communication module for receiving the wireless transmission, a power supply, processor, memory, annunciation system, and RFID module. The RFID module has an RFID receiver that listens for an RFID transmission from an RFID reader disposed in a portal of an area of interest. The PAD identifies the transmission and changes its operating state based on the transmission. The RFID readers recognize, record, and transmit the state of the PAD to a base station providing accountability of the wearer.

  19. Wireless power transfer system

    DOE Patents [OSTI]

    Wu, Hunter; Sealy, Kylee; Gilchrist, Aaron

    2016-02-23

    A system includes a first stage of an inductive power transfer system with an LCL load resonant converter with a switching section, an LCL tuning circuit, and a primary receiver pad. The IPT system includes a second stage with a secondary receiver pad, a secondary resonant circuit, a secondary rectification circuit, and a secondary decoupling converter. The secondary receiver pad connects to the secondary resonant circuit. The secondary resonant circuit connects to the secondary rectification circuit. The secondary rectification circuit connects to the secondary decoupling converter. The second stage connects to a load. The load includes an energy storage element. The second stage and load are located on a vehicle and the first stage is located at a fixed location. The primary receiver pad wirelessly transfers power to the secondary receiver pad across a gap when the vehicle positions the secondary receiver pad with respect to the primary receiver pad.

  20. Transient digitizer with displacement current samplers

    DOE Patents [OSTI]

    McEwan, Thomas E.

    1996-01-01

    A low component count, high speed sample gate, and digitizer architecture using the sample gates is based on use of a signal transmission line, a strobe transmission line and a plurality of sample gates connected to the sample transmission line at a plurality of positions. The sample gates include a strobe pickoff structure near the strobe transmission line which generates a charge displacement current in response to propagation of the strobe signal on the strobe transmission line sufficient to trigger the sample gate. The sample gate comprises a two-diode sampling bridge and is connected to a meandered signal transmission line at one end and to a charge-holding cap at the other. The common cathodes are reverse biased. A voltage step is propagated down the strobe transmission line. As the step propagates past a capacitive pickoff, displacement current i=c(dv/dT), flows into the cathodes, driving the bridge into conduction and thereby charging the charge-holding capacitor to a value related to the signal. A charge amplifier converts the charge on the charge-holding capacitor to an output voltage. The sampler is mounted on a printed circuit board, and the sample transmission line and strobe transmission line comprise coplanar microstrips formed on a surface of the substrate. Also, the strobe pickoff structure may comprise a planar pad adjacent the strobe transmission line on the printed circuit board.

  1. Transient digitizer with displacement current samplers

    DOE Patents [OSTI]

    McEwan, T.E.

    1996-05-21

    A low component count, high speed sample gate, and digitizer architecture using the sample gates is based on use of a signal transmission line, a strobe transmission line and a plurality of sample gates connected to the sample transmission line at a plurality of positions. The sample gates include a strobe pickoff structure near the strobe transmission line which generates a charge displacement current in response to propagation of the strobe signal on the strobe transmission line sufficient to trigger the sample gate. The sample gate comprises a two-diode sampling bridge and is connected to a meandered signal transmission line at one end and to a charge-holding cap at the other. The common cathodes are reverse biased. A voltage step is propagated down the strobe transmission line. As the step propagates past a capacitive pickoff, displacement current i=c(dv/dT), flows into the cathodes, driving the bridge into conduction and thereby charging the charge-holding capacitor to a value related to the signal. A charge amplifier converts the charge on the charge-holding capacitor to an output voltage. The sampler is mounted on a printed circuit board, and the sample transmission line and strobe transmission line comprise coplanar microstrips formed on a surface of the substrate. Also, the strobe pickoff structure may comprise a planar pad adjacent the strobe transmission line on the printed circuit board. 16 figs.

  2. Portable weighing system with alignment features

    DOE Patents [OSTI]

    Abercrombie, Robert Knox; Richardson, Gregory David; Scudiere, Matthew Bligh; Sheldon, Frederick T.

    2012-11-06

    A system for weighing a load is disclosed. The weighing system includes a pad having at least one transducer for weighing a load disposed on the pad. In some embodiments the pad has a plurality of foot members and the weighing system may include a plate that disposed underneath the pad for receiving the plurality of foot member and for aligning the foot members when the weighing system is installed. The weighing system may include a spacer disposed adjacent the pad and in some embodiments, a spacer anchor operatively secures the spacer to a support surface, such as a plate, a railway bed, or a roadway. In some embodiments the spacer anchor operatively secures both the spacer and the pad to a roadway.

  3. Protecting integrated circuits from excessive charge accumulation during plasma cleaning of multichip modules

    DOE Patents [OSTI]

    Rodenbeck, Christopher T; Girardi, Michael

    2015-04-21

    Internal nodes of a constituent integrated circuit (IC) package of a multichip module (MCM) are protected from excessive charge during plasma cleaning of the MCM. The protected nodes are coupled to an internal common node of the IC package by respectively associated discharge paths. The common node is connected to a bond pad of the IC package. During MCM assembly, and before plasma cleaning, this bond pad receives a wire bond to a ground bond pad on the MCM substrate.

  4. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    Refinery and Blender Net Input of Crude Oil and Petroleum Products by PAD and Refining Districts, 2014 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Crude Oil ................................................................. 365,138 31,715 396,853 819,971 168,460 297,342 1,285,773 Natural Gas Plant Liquids and Liquefied

  5. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    Refinery Net Input of Crude Oil and Petroleum Products by PAD and Refining Districts, 2014 (Thousand Barrels, Except Where Noted) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Crude Oil ................................................................. 365,138 31,715 396,853 819,971 168,460 297,342 1,285,773 Natural Gas Plant Liquids

  6. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    5.PDF Table 15. Natural Gas Plant Net Production and Stocks of Petroleum Products by PAD and Refining Districts, January 2014 (Thousand Barrels) Commodity Production PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Natural Gas Liquids ................................................ - 4,181 4,181 3,052 1,959 9,877 14,888 Pentanes Plus

  7. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    6.PDF Table 16. Refinery and Blender Net Input of Crude Oil and Petroleum Products by PAD and Refining Districts, January 2014 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Crude Oil ................................................................. 26,748 2,868 29,616 67,499 14,682 25,866 108,047 Natural Gas Plant Liquids

  8. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    7.PDF Table 17. Refinery and Blender Net Production of Finished Petroleum Products by PAD and Refining Districts, January 2014 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Liquefied Refinery Gases ......................................... 772 -22 750 1,555 -217 39 1,377 Ethane/Ethylene

  9. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    8.PDF Table 18. Refinery Net Input of Crude Oil and Petroleum Products by PAD and Refining Districts, January 2014 (Thousand Barrels, Except Where Noted) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Crude Oil ................................................................. 26,748 2,868 29,616 67,499 14,682 25,866 108,047 Natural Gas Plant

  10. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    9.PDF Table 19. Refinery Net Production of Finished Petroleum Products by PAD and Refining Districts, January 2014 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Liquefied Refinery Gases ......................................... 772 -22 750 1,555 -217 39 1,377 Ethane/Ethylene

  11. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    1.PDF Table 21. Blender Net Production of Petroleum Products by PAD Districts, January 2014 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Finished Motor Gasoline ........................................... 75,867 5,597 81,464 33,855 8,365 9,820 52,040 Reformulated ........................................................

  12. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    2.PDF Table 22. Refinery Stocks of Crude Oil and Petroleum Products by PAD and Refining Districts, January 2014 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Crude Oil ..................................................................... 7,495 446 7,941 9,590 1,697 1,988 13,275 Petroleum Products

  13. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    4.PDF Table 24. Imports of Residual Fuel Oil by Sulfur Content and by PAD District and State of Entry, January 2014 (Thousand Barrels) PAD District and State of Entry Residual Fuel Oil Less than 0.31 % sulfur 0.31 to 1.00 % sulfur Greater than 1.00 % sulfur Total PAD District 1 .......................................................... - 257 1,460 1,717 Connecticut ........................................................... - - - - Delaware

  14. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    2 June 2016 Table 27. Natural Gas Plant Net Production and Stocks of Petroleum Products by PAD and Refining Districts, June 2016 (Thousand Barrels) Commodity Production PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Natural Gas Plant Liquids ...................................... 14 9,851 9,865 6,063 6,470 12,522 25,055 Pentanes Plus

  15. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    3 June 2016 Table 28. Refinery and Blender Net Input of Crude Oil and Petroleum Products by PAD and Refining Districts, June 2016 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Crude Oil ................................................................. 30,787 2,981 33,768 70,174 15,135 25,170 110,479 Natural Gas Plant

  16. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    5 June 2016 Table 29. Refinery and Blender Net Production of Finished Petroleum Products by PAD and Refining Districts, June 2016 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Liquefied Refinery Gases ......................................... 1,589 55 1,644 4,843 625 783 6,251 Ethane/Ethylene

  17. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    7 June 2016 Table 30. Refinery Net Input of Crude Oil and Petroleum Products by PAD and Refining Districts, June 2016 (Thousand Barrels, Except Where Noted) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Crude Oil ................................................................. 30,787 2,981 33,768 70,174 15,135 25,170 110,479 Natural Gas

  18. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    9 June 2016 Table 31. Refinery Net Production of Finished Petroleum Products by PAD and Refining Districts, June 2016 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Liquefied Refinery Gases ......................................... 1,589 55 1,644 4,843 625 783 6,251 Ethane/Ethylene

  19. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    2 June 2016 Table 33. Blender Net Production of Petroleum Products by PAD District, June 2016 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Finished Motor Gasoline ........................................... 92,262 7,022 99,284 45,894 9,917 14,867 70,678 Reformulated

  20. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    3 June 2016 Table 34. Refinery Stocks of Crude Oil and Petroleum Products by PAD and Refining Districts, June 2016 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Crude Oil ..................................................................... 12,055 729 12,784 10,352 2,180 1,915 14,447 Petroleum Products

  1. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    6 June 2016 Table 36. Imports of Residual Fuel Oil by Sulfur Content and by PAD District and State of Entry, June 2016 (Thousand Barrels) PAD District and State of Entry Residual Fuel Oil Less than 0.31 % sulfur 0.31 to 1.00 % sulfur Greater than 1.00 % sulfur Total PAD District 1 .......................................................... 175 896 1,909 2,980 Connecticut ........................................................... - - - - Delaware

  2. Planar multi-electrode array sensor for localized electrochemical corrosion detection

    DOE Patents [OSTI]

    Tormoen, Garth William; Brossia, Christopher Sean

    2014-01-07

    A planarized type of coupled multi-electrode corrosion sensing device. Electrode pads are fabricated on a thin backing, such as a thin film. Each pad has an associated electrical lead for connection to auxiliary electronic circuitry, which may include a resistor associated with each electrical pad. The design permits the device to be easily placed in small crevices or under coatings such as paint.

  3. Clean Cities White Paper Template

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    iii CONTENTS ACKNOWLEDGEMENTS ...................................................................................................... v GLOSSARY ............................................................................................................................. vii 1 INTRODUCTION TO HYDRAULIC FRACTURING AND SHALE GAS PRODUCTION ....................................................................................................... 1 1.1 Road and Well Pad Construction

  4. TABLE52.CHP:Corel VENTURA

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    of Selected Petroleum Products by PAD a Distillate stocks located in the "Northeast Heating Oil Reserve" are not included. For details see Appendix E. W Withheld to avoid...

  5. X:\\L6046\\Data_Publication\\Pma\\current\\ventura\\pma.vp

    U.S. Energy Information Administration (EIA) Indexed Site

    1 Table 33. Oxygenated Motor Gasoline Prices by Grade, Sales Type, and PAD District (Cents per Gallon Excluding Taxes) Geographic Area Month Regular Midgrade Sales to End Users...

  6. TABLE12.CHP:Corel VENTURA

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    PAD District V-Supply, Disposition, and Ending Stocks of Crude Oil and Petroleum Products, January 1998 Crude Oil ...... 67,121 - 13,641 ...

  7. table04.chp:Corel VENTURA

    Gasoline and Diesel Fuel Update (EIA)

    PAD District I-Supply, Disposition, and Ending Stocks of Crude Oil and Petroleum Products, January 1998 Crude Oil ...... 824 - 53,357 -2,000 ...

  8. TABLE27.CHP:Corel VENTURA

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    7. Exports of Crude Oil and Petroleum Products by PAD District, January 1998 Crude Oil a ...... 0 1,168 0 0 5,978 ...

  9. TABLE33.CHP:Corel VENTURA

    Gasoline and Diesel Fuel Update (EIA)

    3. Movements of Crude Oil and Petroleum Products by Pipeline Between PAD Districts, January 1998 Crude Oil ...... 0 433 157 978 ...

  10. TABLE29.CHP:Corel VENTURA

    Gasoline and Diesel Fuel Update (EIA)

    9. Refinery Net Production of Finished Petroleum Products by PAD and Refining Districts, July 2004 Liquefied Refinery Gases ... 2,082 70...

  11. Petroleum supply monthly with data for January 1997

    SciTech Connect (OSTI)

    1997-03-01

    This report presents statistical data on production, imports, exports, PAD district movements, and inventories by the primary suppliers of petroleum products in the United States.

  12. X:\\Data_Publication\\Pma\\current\\ventura\\pma00.vp

    U.S. Energy Information Administration (EIA) Indexed Site

    Energy Information AdministrationPetroleum Marketing Annual 2000 Table 33. Oxygenated Motor Gasoline Prices by Grade, Sales Type, and PAD District (Cents per Gallon Excluding...

  13. Energy Information Administration / Petroleum Marketing Annual...

    U.S. Energy Information Administration (EIA) Indexed Site

    55 Energy Information Administration Petroleum Marketing Annual 1997 Prices of Petroleum Products Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District, and State...

  14. TABLE11.CHP:Corel VENTURA

    Gasoline and Diesel Fuel Update (EIA)

    (Thousand Barrels) Table 11. PAD District II-Year-to-Date Supply, Disposition, and Ending Stocks of Crude Oil and Petroleum January-July 2004 Products, Crude Oil...

  15. TABLE15.CHP:Corel VENTURA

    Gasoline and Diesel Fuel Update (EIA)

    Table 15. PAD District III-Year-to-Date Supply, Disposition, and Ending Stocks of Crude Oil and Petroleum (Thousand Barrels) January-July 2004 Products, Crude Oil...

  16. TABLE19.CHP:Corel VENTURA

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Table 19. PAD District IV-Year-to-Date Supply, Disposition, and Ending Stocks of Crude Oil and Petroleum (Thousand Barrels) January-July 2004 Products, Crude Oil...

  17. Table A2. Refiner/Reseller Prices of Aviation Fuels, Propane...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Marketing Annual 1999 421 Table A2. RefinerReseller Prices of Aviation Fuels, Propane, and Kerosene, by PAD District, 1983-Present (Cents per Gallon Excluding Taxes) -...

  18. Table 49. Prime Supplier Sales Volumes of Aviation Fuels, Propane...

    Gasoline and Diesel Fuel Update (EIA)

    See footnotes at end of table. 49. Prime Supplier Sales Volumes of Aviation Fuels, Propane, and Residual Fuel Oil by PAD District and State 386 Energy Information...

  19. Table 49. Prime Supplier Sales Volumes of Aviation Fuels, Propane...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Marketing Annual 1998 Table 49. Prime Supplier Sales Volumes of Aviation Fuels, Propane, and Residual Fuel Oil by PAD District and State (Thousand Gallons per Day) -...

  20. Table 49. Prime Supplier Sales Volumes of Aviation Fuels, Propane...

    U.S. Energy Information Administration (EIA) Indexed Site

    Marketing Annual 1995 Table 49. Prime Supplier Sales Volumes of Aviation Fuels, Propane, and Residual Fuel Oil by PAD District and State (Thousand Gallons per Day) -...

  1. Table A2. Refiner/Reseller Prices of Aviation Fuels, Propane...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Marketing Annual 1995 467 Table A2. RefinerReseller Prices of Aviation Fuels, Propane, and Kerosene, by PAD District, 1983-Present (Cents per Gallon Excluding Taxes) -...

  2. This Week In Petroleum Printer-Friendly Version

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    region (PAD District II) accounts for the highest concentration of consumers that use propane for heating in the nation, the South Atlantic and East South Central regions, as...

  3. Table 49. Prime Supplier Sales Volumes of Aviation Fuels, Propane...

    Gasoline and Diesel Fuel Update (EIA)

    Marketing Annual 1999 Table 49. Prime Supplier Sales Volumes of Aviation Fuels, Propane, and Residual Fuel Oil by PAD District and State (Thousand Gallons per Day) -...

  4. --No Title--

    U.S. Energy Information Administration (EIA) Indexed Site

    See footnotes at end of table. Table 1A. Refiner Acquisition Cost of Crude Oil by PAD Districts (Dollars per Barrel) - Continued...

  5. Fact Sheet: Energy Storage Testing and Validation (October 2012)

    Broader source: Energy.gov [DOE]

    At Sandia National Laboratories, the Energy Storage Analysis Laboratory, in conjunction with the Energy Storage Test Pad, provides independent testing and validation of electrical energy storage...

  6. TABLE32.CHP:Corel VENTURA

    Gasoline and Diesel Fuel Update (EIA)

    Imports of Residual Fuel Oil by Sulfur Content and by PAD District and State of Entry, Source: Energy Information Administration (EIA) Form EIA-814, "Monthly Imports Report." July...

  7. TABLE27.CHP:Corel VENTURA

    Gasoline and Diesel Fuel Update (EIA)

    Natural Gas Plant Net Production and Stocks of Petroleum Products by PAD and Refining Note: Refer to Appendix A for Refining District descriptions. Source: Energy Information...

  8. Microsoft Word - Inspection of TRUPACT-III Changes.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    such as removing a concrete pad, installing a hood ventilation system, bolting robot, bolt and coverlid rack, pallet dispenser, payload transfer station, and VOC monitoring ...

  9. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    on geothermal heat pumps, air source heat pumps, central air conditioning, a variety of dairy equipment, heat lamps and pads, equipment controls, recovery ventilators, circulation...

  10. X:\\Data_Publication\\Pma\\current\\ventura\\pma00.vp

    U.S. Energy Information Administration (EIA) Indexed Site

    by PAD District and State (Thousand Gallons per Day) - Continued Geographic Area Month Aviation Gasoline Naphtha- Type Jet Fuel Kerosene- Type Jet Fuel Propane (Consumer Grade)...

  11. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    by PAD District and State (Thousand Gallons per Day) - Continued Geographic Area Month Aviation Gasoline Kerosene-Type Jet Fuel Kerosene No. 1 Distillate Propane (Consumer...

  12. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    by PAD District and State (Thousand Gallons per Day) - Continued Geographic Area Month Aviation Gasoline Kerosene- Type Jet Fuel No. 4 Fuel Oil a Propane (Consumer Grade)...

  13. X:\\L6046\\Data_Publication\\Pma\\current\\ventura\\pma.vp

    U.S. Energy Information Administration (EIA) Indexed Site

    by PAD District and State (Thousand Gallons per Day) - Continued Geographic Area Month Aviation Gasoline Kerosene- Type Jet Fuel Propane (Consumer Grade) Residual Fuel Oil...

  14. X:\\L6046\\Data_Publication\\Pma\\current\\ventura\\pma.vp

    U.S. Energy Information Administration (EIA) Indexed Site

    by PAD District and State (Thousand Gallons per Day) - Continued Geographic Area Month Aviation Gasoline Kerosene-Type Jet Fuel Kerosene No. 1 Distillate Propane (Consumer...

  15. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    by PAD District and State (Thousand Gallons per Day) - Continued Geographic Area Month Aviation Gasoline Kerosene- Type Jet Fuel Propane (Consumer Grade) Residual Fuel Oil...

  16. X:\\L6046\\Data_Publication\\Pma\\current\\ventura\\pma.vp

    U.S. Energy Information Administration (EIA) Indexed Site

    by PAD District and State (Thousand Gallons per Day) - Continued Geographic Area Month Aviation Gasoline Naphtha- Type Jet Fuel Kerosene- Type Jet Fuel Propane (Consumer Grade)...

  17. Table 21. Domestic Crude Oil First Purchase Prices

    U.S. Energy Information Administration (EIA) Indexed Site

    Administration Petroleum Marketing Annual 1996 41 Table 21. Domestic Crude Oil First Purchase Prices (Dollars per Barrel) - Continued Year Month PAD District II...

  18. Table 21. Domestic Crude Oil First Purchase Prices

    U.S. Energy Information Administration (EIA) Indexed Site

    AdministrationPetroleum Marketing Annual 1998 41 Table 21. Domestic Crude Oil First Purchase Prices (Dollars per Barrel) - Continued Year Month PAD District II...

  19. Table 21. Domestic Crude Oil First Purchase Prices

    U.S. Energy Information Administration (EIA) Indexed Site

    Administration Petroleum Marketing Annual 1995 41 Table 21. Domestic Crude Oil First Purchase Prices (Dollars per Barrel) - Continued Year Month PAD District II...

  20. X:\\L6046\\Data_Publication\\Pma\\current\\ventura\\pma.vp

    U.S. Energy Information Administration (EIA) Indexed Site

    2 Table 33. Oxygenated Motor Gasoline Prices by Grade, Sales Type, and PAD District (Cents per Gallon Excluding Taxes) Geographic Area Month Regular Midgrade Sales to End Users...

  1. Crude Oil Prices Table 21. Domestic Crude Oil First Purchase...

    U.S. Energy Information Administration (EIA) Indexed Site

    Information Administration Petroleum Marketing Annual 1995 41 Table 21. Domestic Crude Oil First Purchase Prices (Dollars per Barrel) - Continued Year Month PAD District II...

  2. Crude Oil Prices

    U.S. Energy Information Administration (EIA) Indexed Site

    Information AdministrationPetroleum Marketing Annual 2001 41 Table 21. Domestic Crude Oil First Purchase Prices (Dollars per Barrel) - Continued Year Month PAD District II...

  3. Crude Oil Prices

    U.S. Energy Information Administration (EIA) Indexed Site

    Information AdministrationPetroleum Marketing Annual 1998 41 Table 21. Domestic Crude Oil First Purchase Prices (Dollars per Barrel) - Continued Year Month PAD District II...

  4. Crude Oil Prices

    U.S. Energy Information Administration (EIA) Indexed Site

    Information AdministrationPetroleum Marketing Annual 1999 41 Table 21. Domestic Crude Oil First Purchase Prices (Dollars per Barrel) - Continued Year Month PAD District II...

  5. NREL: Transportation Research - Vehicle Thermal Management Facilities

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    a test pad to conduct vehicle thermal soak testing and stationary heating, ventilation, and air conditioning (HVAC) load testing on light-, medium-, and heavy-duty vehicles. ...

  6. Workbook Contents

    U.S. Energy Information Administration (EIA) Indexed Site

    Net Receipts by Pipeline, Tanker, Barge and Rail between PAD Districts" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description"," Of...

  7. ,"Total Crude Oil and Petroleum Products Net Receipts by Pipeline...

    U.S. Energy Information Administration (EIA) Indexed Site

    Net Receipts by Pipeline, Tanker, Barge and Rail between PAD Districts" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description"," Of...

  8. Workbook Contents

    U.S. Energy Information Administration (EIA) Indexed Site

    Movements by Tanker, Pipeline, Barge and Rail between PAD Districts" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description"," Of Series","Frequency","La...

  9. Workbook Contents

    U.S. Energy Information Administration (EIA) Indexed Site

    Tanker, Pipeline, Barge and Rail between PAD Districts" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description"," Of Series","Frequency","Latest Data...

  10. Prime Supplier Sales Volumes of Distillate Fuel Oils and Kerosene...

    Gasoline and Diesel Fuel Update (EIA)

    Marketing Annual 1997 401 Table 50. Prime Supplier Sales Volumes of Distillate Fuel Oils and Kerosene by PAD District and State (Thousand Gallons per Day) - Continued...

  11. Table 46. Refiner No. 2 Distillate, Diesel Fuel, and Fuel Oil...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Petroleum Marketing Annual 1999 295 Table 46. Refiner No. 2 Distillate, Diesel Fuel, and Fuel Oil Volumes by PAD District and State (Thousand Gallons per Day) - Continued...

  12. Table 50. Prime Supplier Sales Volumes of Distillate Fuel Oils...

    U.S. Energy Information Administration (EIA) Indexed Site

    Marketing Annual 1999 359 Table 50. Prime Supplier Sales Volumes of Distillate Fuel Oils and Kerosene by PAD District and State (Thousand Gallons per Day) - Continued...

  13. DOE Fuel Cell Pre-Solicitation Workshop - Breakout Group 2: MEAs...

    Broader source: Energy.gov (indexed) [DOE]

    ...opmeacomponents.pdf (67.78 KB) More Documents & Publications Breakout Group 3: Water Management Breakout Group 2: Membrane Electrode Assemblies FC-PAD Organization and Activities

  14. Containment System Michael F

    Office of Scientific and Technical Information (OSTI)

    to reduce their liability, lower their insurance costs, or ... done on the same concrete pad which saves construction cost. ... Another innovation in rotational molded polyethylene is a ...

  15. --No Title--

    U.S. Energy Information Administration (EIA) Indexed Site

    See footnotes at end of table. Table 1A. Refiner Acquisition Cost of Crude Oil by PAD Districts (Dollars per Barrel) - Continued ...

  16. Program Update: 3rd Quarter 2013 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Community and Science; LM Completes Construction of Well Pad at CNTA; DOE Salute - Grand Junction, Colorado, Business Incubator of the Year; Replacement of Rocky Flats Water ...

  17. Working and Net Available Shell Storage Capacity

    U.S. Energy Information Administration (EIA) Indexed Site

    ... Source: Energy Information Administration, Form EIA-813 "Monthly Crude Oil Report", Form EIA-815 "Monthly Bulk Terminal and Blender Report" PAD Districts 1 EIAWorking and Net ...

  18. Personal Annunciation Device - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... of the PAD to a base station providing accountability of the wearer. Y-12 National Security Complex 01252011 Issued Technology Status Technology ID Development Stage ...

  19. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    Information AdministrationPetroleum Marketing Annual 2009 Table 18. Domestic Crude Oil First Purchase Prices (Dollars per Barrel) - Continued Year Month PAD District II...

  20. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    Information AdministrationPetroleum Marketing Annual 2008 Table 18. Domestic Crude Oil First Purchase Prices (Dollars per Barrel) - Continued Year Month PAD District II...

  1. Widget:DivContentWrapper | Open Energy Information

    Open Energy Info (EERE)

    div For example: Widget:DivContentWrapper | classui-corner-all | stylebackground-color: green; padding: 5px; color: white; | contentText Text Retrieved from "http:...

  2. 2010 New Fuel Cell Projects Meeting Agenda | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PDF icon 2010newfcmeetingagenda.pdf More Documents & Publications DOE 2010 Fuel Cell Pre-Solicitation Workshop Agenda Fuel Cell Bus Workshop FC-PAD Organization and Activities

  3. Durability Improvements Through Degradation Mechanism Studies...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PDF icon boruplanlkickoff.pdf More Documents & Publications FC-PAD Organization and Activities Fuel Cell Projects Kickoff Meeting The Science And Engineering of Duralbe Ultralow ...

  4. RAPID/Geothermal/Well Field/Oregon | Open Energy Information

    Open Energy Info (EERE)

    pipe, well pad, access road construction, etc). Local Well Field Process not available Policies & Regulations ORS 517 - Mining and Mining Claims ORS 522.135 Permit Time Limit...

  5. DOE/EA-2024

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... pads required for the diesel generators, breathing air compressor, and gas ... limit workplace atmospheric and drinking water concentrations of potentially hazardous chemicals. ...

  6. Petroleum Products Table 43. Refiner Motor Gasoline Volumes...

    U.S. Energy Information Administration (EIA) Indexed Site

    of table. 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State 262 Energy Information Administration Petroleum Marketing Annual 1997 Table 43....

  7. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    Table 39. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per Day) Geographic Area Month Regular Midgrade Sales to End Users...

  8. Petroleum Products Table 43. Refiner Motor Gasoline Volumes...

    U.S. Energy Information Administration (EIA) Indexed Site

    1995 Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per Day) - Continued Geographic Area Month Premium All Grades Sales...

  9. Petroleum Products Table 43. Refiner Motor Gasoline Volumes...

    U.S. Energy Information Administration (EIA) Indexed Site

    2000 Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per Day) - Continued Geographic Area Month Premium All Grades Sales...

  10. X:\\L6046\\Data_Publication\\Pma\\current\\ventura\\pma.vp

    U.S. Energy Information Administration (EIA) Indexed Site

    Table 39. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per Day) Geographic Area Month Regular Midgrade Sales to End Users...

  11. Petroleum Products Table 31. Motor Gasoline Prices by Grade...

    U.S. Energy Information Administration (EIA) Indexed Site

    Annual 1995 Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon Excluding Taxes) - Continued Geographic Area Month Premium All...

  12. Petroleum Products Table 31. Motor Gasoline Prices by Grade...

    U.S. Energy Information Administration (EIA) Indexed Site

    Annual 2000 Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon Excluding Taxes) - Continued Geographic Area Month Premium All...

  13. Petroleum Products Table 43. Refiner Motor Gasoline Volumes...

    U.S. Energy Information Administration (EIA) Indexed Site

    of table. 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State 262 Energy Information Administration Petroleum Marketing Annual 1996 Table 43....

  14. Petroleum Products Table 31. Motor Gasoline Prices by Grade...

    U.S. Energy Information Administration (EIA) Indexed Site

    at end of table. 31. Motor Gasoline Prices by Grade, Sales Type, PAD District, and State 56 Energy Information Administration Petroleum Marketing Annual 1996 Table 31. Motor...

  15. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per Day) Geographic Area Month Regular Midgrade Sales to End Users...

  16. untitled

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    of Aviation Fuels and Kerosene by PAD District and State (Cents per Gallon Excluding Taxes) - Continued Geographic Area Month Aviation Gasoline Kerosene-Type Jet Fuel Kerosene...

  17. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    Gasoline Prices by Grade, Sales Type, and PAD District (Cents per Gallon Excluding Taxes) Geographic Area Month Regular Midgrade Sales to End Users Sales for Resale Sales to...

  18. X:\\L6046\\Data_Publication\\Pma\\current\\ventura\\pma.vp

    U.S. Energy Information Administration (EIA) Indexed Site

    Gasoline Prices by Grade, Sales Type, and PAD District (Cents per Gallon Excluding Taxes) Geographic Area Month Regular Midgrade Sales to End Users Sales for Resale Sales to...

  19. Table 41. No. 2 Diesel Fuel Prices by Sulfur Content, Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    Content, Sales Type, and PAD District 242 Energy Information Administration Petroleum Marketing Annual 1997 Table 41. No. 2 Diesel Fuel Prices by Sulfur Content, Sales Type,...

  20. Table 41. No. 2 Diesel Fuel Prices by Sulfur Content, Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    Content, Sales Type, and PAD District 242 Energy Information Administration Petroleum Marketing Annual 1996 Table 41. No. 2 Diesel Fuel Prices by Sulfur Content, Sales Type,...

  1. PRELIMINARY SURVEY OF TEXAS CITY CHEMICALS, INC.

    Office of Legacy Management (LM)

    status of those facilities utilized under Atomic Energy Commission (AEC) contract during ... the pad was performed, consisting of gamma-ray exposure rate measurements made at a height ...

  2. --No Title--

    Gasoline and Diesel Fuel Update (EIA)

    PAD District 1 (East Coast) is composed of the following three subdistricts: Subdistrict 1A (New England): Connecticut, Maine, Massachusetts, New Hampshire, Rhode Island, Vermont. ...

  3. SEP Success Story: Launching Green Entrepreneurship in New Hampshire

    Office of Energy Efficiency and Renewable Energy (EERE)

    This summer, five green companies in New Hampshire are participating in an intensive business accelerator initiative called the Green Launching Pad (GLP). Learn more.

  4. U.S. Total Imports of Residual Fuel

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Area: U.S. Total PAD District 1 Connecticut Delaware Florida Georgia Maine Maryland Massachusetts New Hampshire New Jersey New York North Carolina Pennsylvania Rhode Island South ...

  5. vol2app.chp:Corel VENTURA

    Gasoline and Diesel Fuel Update (EIA)

    PAD District I East Coast: District of Columbia and the States of Maine, New Hampshire, Vermont, Massachusetts, Rhode Island, Connecticut, New Jersey, Delaware, Maryland, Virginia, ...

  6. U.S. Refinery, Bulk Terminal, and Natural Gas Plant Stocks of...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Area: U.S. PAD District 1 Connecticut Delaware District of Columbia Florida Georgia Maine Maryland Massachusetts New Hampshire New Jersey New York North Carolina Pennsylvania Rhode ...

  7. GREET Development and Applications for Life-Cycle Analysis of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... covering gasoline, diesel, jet fuel, LPG, etc. 14 PAD ... Fuel Cell Auxiliary MotorGenerator Controller Chassis Transmission Powertrain Body Lifetime VMT 160,000 mi Impacts ...

  8. untitled

    Gasoline and Diesel Fuel Update (EIA)

    Imports of Residual Fuel Oil by Sulfur Content and by PAD District and State of Entry, ... Source: Energy Information Administration (EIA) Form EIA-814, "Monthly Imports Report." U. ...

  9. Transportation and the 'Campus of the Future' (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2012-02-01

    Fact sheet on Vehicle Testing and Integration Facility, featuring the Vehicle Modification Facility, Vehicle Test Pad and RECharge Integrated Demonstration System.

  10. Table 34. Reformulated Motor Gasoline Prices by Grade, Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    Information AdministrationPetroleum Marketing Annual 1999 Table 34. Reformulated Motor Gasoline Prices by Grade, Sales Type, PAD District, and Selected States (Cents per...

  11. Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type...

    U.S. Energy Information Administration (EIA) Indexed Site

    Energy Information Administration Petroleum Marketing Annual 1995 Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  12. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    7 Table 33. Oxygenated Motor Gasoline Prices by Grade, Sales Type, and PAD District (Cents per Gallon Excluding Taxes) Geographic Area Month Regular Midgrade Sales to End Users...

  13. Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    250 Energy Information AdministrationPetroleum Marketing Annual 1999 Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales Type, PAD District, and State (Thousand Gallons...

  14. Table 32. Conventional Motor Gasoline Prices by Grade, Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    Information Administration Petroleum Marketing Annual 1995 Table 32. Conventional Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  15. Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    Energy Information Administration Petroleum Marketing Annual 1995 Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales Type, PAD District, and State (Thousand Gallons...

  16. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    221 Volumes of Petroleum Products Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per Day) Geographic Area Month Regular...

  17. Table 48. Prime Supplier Sales Volumes of Motor Gasoline by...

    U.S. Energy Information Administration (EIA) Indexed Site

    Petroleum Marketing Annual 1998 Table 48. Prime Supplier Sales Volumes of Motor Gasoline by Grade, Formulation, PAD District, and State (Thousand Gallons per Day) -...

  18. Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type...

    U.S. Energy Information Administration (EIA) Indexed Site

    134 Energy Information AdministrationPetroleum Marketing Annual 1998 Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  19. Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type...

    U.S. Energy Information Administration (EIA) Indexed Site

    134 Energy Information AdministrationPetroleum Marketing Annual 1999 Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  20. Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type...

    U.S. Energy Information Administration (EIA) Indexed Site

    220 Energy Information AdministrationPetroleum Marketing Annual 1998 Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per...

  1. Table 33. Oxygenated Motor Gasoline Prices by Grade, Sales Type...

    U.S. Energy Information Administration (EIA) Indexed Site

    - - - - - - - - - - - - See footnotes at end of table. 33. Oxygenated Motor Gasoline Prices by Grade, Sales Type, PAD District, and State 116 Energy Information...

  2. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    9 Volumes of Petroleum Products Table 39. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per Day) Geographic Area Month Regular...

  3. Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    - - - - W W - - - - - - See footnotes at end of table. 44. Refiner Motor Gasoline Volumes by Formulation, Sales Type, PAD District, and State 292 Energy...

  4. Table 48. Prime Supplier Sales Volumes of Motor Gasoline by...

    U.S. Energy Information Administration (EIA) Indexed Site

    Petroleum Marketing Annual 1999 Table 48. Prime Supplier Sales Volumes of Motor Gasoline by Grade, Formulation, PAD District, and State (Thousand Gallons per Day) -...

  5. Table 34. Reformulated Motor Gasoline Prices by Grade, Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    Information AdministrationPetroleum Marketing Annual 1998 Table 34. Reformulated Motor Gasoline Prices by Grade, Sales Type, PAD District, and Selected States (Cents per...

  6. Table 32. Conventional Motor Gasoline Prices by Grade, Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    - - - - W W - - - - - - See footnotes at end of table. 32. Conventional Motor Gasoline Prices by Grade, Sales Type, PAD District, and State 86 Energy Information...

  7. Table 48. Prime Supplier Sales Volumes of Motor Gasoline by...

    U.S. Energy Information Administration (EIA) Indexed Site

    Petroleum Marketing Annual 1995 Table 48. Prime Supplier Sales Volumes of Motor Gasoline by Grade, Formulation, PAD District, and State (Thousand Gallons per Day) -...

  8. Table 32. Conventional Motor Gasoline Prices by Grade, Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    - - - - 64.7 64.7 - - - - - - See footnotes at end of table. 32. Conventional Motor Gasoline Prices by Grade, Sales Type, PAD District, and State 86 Energy Information...

  9. Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    250 Energy Information AdministrationPetroleum Marketing Annual 1998 Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales Type, PAD District, and State (Thousand Gallons...

  10. Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type...

    U.S. Energy Information Administration (EIA) Indexed Site

    220 Energy Information AdministrationPetroleum Marketing Annual 1999 Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per...

  11. Table 34. Reformulated Motor Gasoline Prices by Grade, Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    Information Administration Petroleum Marketing Annual 1995 Table 34. Reformulated Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  12. Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type...

    U.S. Energy Information Administration (EIA) Indexed Site

    Energy Information Administration Petroleum Marketing Annual 1995 Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per...

  13. Table 32. Conventional Motor Gasoline Prices by Grade, Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    Information AdministrationPetroleum Marketing Annual 1998 Table 32. Conventional Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  14. Table 33. Oxygenated Motor Gasoline Prices by Grade, Sales Type...

    U.S. Energy Information Administration (EIA) Indexed Site

    Information Administration Petroleum Marketing Annual 1995 Table 33. Oxygenated Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  15. Glossary API Gravity: An

    U.S. Energy Information Administration (EIA) Indexed Site

    Florida, Georgia, North Carolina, South Carolina, Virginia, West Virginia. PAD District II: Illinois, Indiana, Iowa, Kansas, Kentucky, Michigan, Minnesota, Missouri, Nebraska,...

  16. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    Florida, Georgia, North Carolina, South Carolina, Virginia, West Virginia. PAD District II: Illinois, Indiana, Iowa, Kansas, Kentucky, Michigan, Minnesota, Missouri, Nebraska,...

  17. X:\\L6046\\Data_Publication\\Pma\\current\\ventura\\pma.vp

    U.S. Energy Information Administration (EIA) Indexed Site

    Florida, Georgia, North Carolina, South Carolina, Virginia, West Virginia. PAD District II: Illinois, Indiana, Iowa, Kansas, Kentucky, Michigan, Minnesota, Missouri, Nebraska,...

  18. TABLE15.CHP:Corel VENTURA

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    5. Natural Gas Plant Net Production and Stocks of Petroleum Products by PAD and Refining ... Report." 170 Table 15. Natural Gas Plant Net Production and Stocks of Petroleum ...

  19. Universal penetration test apparatus with fluid penetration sensor

    DOE Patents [OSTI]

    Johnson, P.W.; Stampfer, J.F.; Bradley, O.D.

    1999-02-02

    A universal penetration test apparatus is described for measuring resistance of a material to a challenge fluid. The apparatus includes a pad saturated with the challenge fluid. The apparatus includes a compression assembly for compressing the material between the pad and a compression member. The apparatus also includes a sensor mechanism for automatically detecting when the challenge fluid penetrates the material. 23 figs.

  20. Universal penetration test apparatus with fluid penetration sensor

    DOE Patents [OSTI]

    Johnson, Phillip W.; Stampfer, Joseph F.; Bradley, Orvil D.

    1999-01-01

    A universal penetration test apparatus for measuring resistance of a material to a challenge fluid. The apparatus includes a pad saturated with the challenge fluid. The apparatus includes a compression assembly for compressing the material between the pad and a compression member. The apparatus also includes a sensor mechanism for automatically detecting when the challenge fluid penetrates the material.