Sample records for ultra-low sulfur diesel

  1. Update on Transition to Ultra-Low-Sulfur Diesel Fuel (released in AEO2006)

    Reports and Publications (EIA)

    2006-01-01T23:59:59.000Z

    On November 8, 2005, the Environmental Protection Agency (EPA) Administrator signed a direct final rule that will shift the retail compliance date for offering ultra-low sulfur diesel (ULSD) for highway use from September 1, 2006, to October 15, 2006. The change will allow more time for retail outlets and terminals to comply with the new 15 parts per million (ppm) sulfur standard, providing time for entities in the diesel fuel distribution system to flush higher sulfur fuel out of the system during the transition. Terminals will have until September 1, 2006, to complete their transitions to ULSD. The previous deadline was July 15, 2006.

  2. Navy Mobility Fuels Forecasting System Phase 5 report: Impacts of ultra low sulfur diesel fuel production on Navy fuel availability

    SciTech Connect (OSTI)

    Hadder, G.R.; Das, S.; Lee, R.; Domingo, N.; Davis, R.M.

    1989-09-01T23:59:59.000Z

    Legislation for ultra low sulfur (ULS) diesel fuel, with a greatly reduced allowable sulfur content and a new limit on aromatics content, is expected to be in place by 1995. The ULS diesel fuel has been specified to satisfy national standards for particulate emissions from heavy-duty diesel engines. The economic and engineering models of the Navy Mobility Fuels Forecasting System have been used to study the impacts of ULS diesel fuel production on other refined petroleum products, with emphasis on the quality of Navy mobility fuels. The study predicts that to produce ULS diesel fuel, Gulf and West Coast refiners will have to invest about $4.4 billion in new processing capacity. Refiners will shift aromatics from No. 2 diesel fuel to jet fuel and to No. 2 fuel oil. Therefore, particulate emissions could be transferred from the nation's highways to the airways and to communities which use No. 2 fuel oil for residential and commercial heating. The study also predicts that there will be an increase in the aromatics content of domestically produced Navy JP-5 jet fuel and F-76 marine diesel fuel. The gum-forming tendencies of F-76 an F-77 burner fuel oil will increase in most cases. The freezing point of JP-5 will improve. There will be minor changes in the cost of JP-5, but sizable reductions in the cost of F-76 and F-77. 20 refs., 2 figs., 17 tabs.

  3. Full Useful Life (120,000 miles) Exhaust Emission Performance of a NOx Adsorber and Diesel Particle Filter Equipped Passenger Car and Medium-duty Engine in Conjunction with Ultra Low Sulfur Fuel (Presentation)

    SciTech Connect (OSTI)

    Thornton, M.; Tatur, M.; Tomazic, D.; Weber, P.; Webb, C.

    2005-08-25T23:59:59.000Z

    Discusses the full useful life exhaust emission performance of a NOx (nitrogen oxides) adsorber and diesel particle filter equipped light-duty and medium-duty engine using ultra low sulfur diesel fuel.

  4. Adaptive Injection Strategies (AIS) for Ultra-low Emissions Diesel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Injection Strategies (AIS) for Ultra-low Emissions Diesel Engines Adaptive Injection Strategies (AIS) for Ultra-low Emissions Diesel Engines Presentation given at the 2007 Diesel...

  5. Cost-benefit analysis of ultra-low sulfur jet fuel

    E-Print Network [OSTI]

    Kuhn, Stephen (Stephen Richard)

    2010-01-01T23:59:59.000Z

    The growth of aviation has spurred increased study of its environmental impacts and the possible mitigation thereof. One emissions reduction option is the introduction of an Ultra Low Sulfur (ULS) jet fuel standard for ...

  6. Ultra-Low Sulfur diesel Update & Future Light Duty Diesel

    Broader source: Energy.gov (indexed) [DOE]

    MARATHON PETROLEUM COMPANY LLC PARENT-MARATHON OIL COMPANY FIFTH LARGEST US REFINERY (OVER 1 MILLION BBLS OF CRUDE CAPACITY) MAJOR MARKETS IN MIDWEST AND SOUTHEAST ...

  7. Biodiesel Effects on Diesel Particle Filter Performance: Milestone Report

    SciTech Connect (OSTI)

    Williams, A.; McCormick, R. L.; Hayes, R.; Ireland, J.

    2006-03-01T23:59:59.000Z

    Research results on the performance of biodiesel and biodiesel blends with ultra-low sulfur diesel (ULSD) and a diesel particle filter (DPF).

  8. Effect of Biodiesel Blends on Diesel Particulate Filter Performance

    SciTech Connect (OSTI)

    Williams, A.; McCormick, R. L.; Hayes, R. R.; Ireland, J.; Fang, H. L.

    2006-11-01T23:59:59.000Z

    Presents results of tests of ultra-low sulfur diesel blended with soy-biodiesel at 5 percent using a Cummins ISB engine with a diesel particulate filter.

  9. Ultra-low Sulfur Reduction Emission Control Device/Development of an On-board Fuel Sulfur Trap

    SciTech Connect (OSTI)

    Rohrbach, Ron; Barron, Ann

    2008-07-31T23:59:59.000Z

    Honeywell has completed working on a multiyear program to develop and demonstrate proof-of-concept for an 'on-vehicle' desulfurization fuel filter for both light duty and heavy-duty diesel engines. Integration of the filter into the vehicle fuel system will reduce the adverse effects sulfur has on post combustion emission control devices such as NOx adsorbers. The NOx adsorber may be required to meet the proposed new EPA Tier II and '2007-Rule' emission standards. The proposed filter concept is based on Honeywell's reactive filtration technology and experience in liquids handling and conditioning. A regeneration and recycling plan for the spent filters was also examined. We have chosen to develop and demonstrate this technology based on criteria set forth for a heavy duty CIDI engine system because it represents a more challenging set of conditions of service intervals and overall fuel usage over light duty systems. In the second phase of the program a light duty diesel engine test was also demonstrated. Further, technology developed under this proposal would also have application for the use of liquid based fuels for fuel cell power generation. The program consisted of four phases. Phase I focused on developing a concept design and analysis and resolution of technical barriers concerning removal of sulfur-containing species in low sulfur fuels. In Phase II concentrated on prototype filter design and preparation followed by qualification testing of this component in a fuel line application. Phase III studied life cycle and regeneration options for the spent filter. Phase IV focused on efficacy and benefits in the desulfation steps of a NOx adsorber on both a heavy and light duty engine. The project team included a number of partners, with Honeywell International as the prime contractor. The partners include an emission control technology developer (Honeywell International), a fuel technology developer (Marathon Ashland Petroleum), a catalyst technology developer (Johnson Matthey), a CIDI engine manufacturer (Navistar Inc. (formerly International Truck & Engine Corporation) and Mack Trucks Inc.), and filter recycler (American Wastes Industries).

  10. ULTRA-LOW SULFUR REDUCTION EMISSION CONTROL DEVICE/DEVELOPMENT OF AN ON-BOARD FUEL SULFUR TRAP

    SciTech Connect (OSTI)

    Ron Rohrbach; Gary Zulauf; Tim Gavin

    2003-04-01T23:59:59.000Z

    Honeywell is actively working on a 3-year program to develop and demonstrate proof-of-concept for an ''on-vehicle'' desulfurization fuel filter for heavy-duty diesel engines. Integration of the filter into the vehicle fuel system will reduce the adverse effects sulfur has on post combustion emission control devices such as NO{sub x} adsorbers. The NO{sub x} adsorber may be required to meet the proposed new EPA Tier II and ''2007-Rule'' emission standards. The proposed filter concept is based on Honeywell's reactive filtration technology and experience in liquids handling and conditioning. A regeneration and recycling plan for the spent filters will also be examined. We have chosen to develop and demonstrate this technology based on criteria set forth for a heavy duty CIDI engine system because it represents a more challenging set of conditions of service intervals and overall fuel usage over light duty systems. It is anticipated that the technology developed for heavy-duty applications will be applicable to light-duty as well. Further, technology developed under this proposal would also have application for the use of liquid based fuels for fuel cell power generation. The program consists of four phases. Phase I will focus on developing a concept design and analysis and resolution of technical barriers concerning removal of sulfur-containing species in low sulfur fuels. In Phase II we will concentrate on prototype filter design and preparation followed by qualification testing of this component in a fuel line application. Phase III will study life cycle and regeneration options for the spent filter. Phase IV will focus on efficacy and life testing and component integration. The project team will include a number of partners, with Honeywell International as the prime contractor. The partners include an emission control technology developer (Honeywell International), a fuel technology developer (Marathon Ashland Petroleum), a catalyst technology developer (Johnson Matthey), a CIDI engine manufacturer (Mack Trucks Inc.), a filter recycler (American Wastes Industries), and a low-sulfur fuel supplier (Equilon, a joint venture between Shell and Texaco).

  11. Ultra-Low Sulfur diesel Update & Future Light Duty Diesel | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your DensityEnergy U.S.-China Electric Vehicle and BatteryUS-EU-Japan

  12. Sulfur Poisoning and Regeneration of NOx Storage-Reduction Cu/K2Ti2O5 Qiang Wang,*,

    E-Print Network [OSTI]

    Guo, John Zhanhu

    a maximum value of 15 ppm sulfur content in diesel fuel, and this ultra-low-sulfur fuel is expectedSulfur Poisoning and Regeneration of NOx Storage-Reduction Cu/K2Ti2O5 Catalyst Qiang Wang,*, Jiahua of sulfur has not been investigated. In this article, the sulfur poisoning of the NOx storage

  13. Diesel Emission Control -- Sulfur Effects (DECSE) Program; Phase I Interim Data Report No. 4: Diesel Particulate Filters -- Final Report

    SciTech Connect (OSTI)

    DOE; ORNL; NREL; EMA; MECA

    2000-01-15T23:59:59.000Z

    The Diesel Emission Control-Sulfur Effects (DECSE) is a joint government/industry program to determine the impact of diesel fuel sulfur levels on emission control systems whose use could lower emissions of nitrogen oxides (NOx) and particulate matter (PM) from on-highway trucks in the 2002--2004 model years. Phase 1 of the program was developed with the following objectives in mind: (1) evaluate the effects of varying the level of sulfur content in the fuel on the emission reduction performance of four emission control technologies; and (2) measure and compare the effects of up to 250 hours of aging on selected devices for multiple levels of fuel sulfur content. This is the fourth and final report for the DPF test program and covers the effect of diesel sulfur level on: a catalyzed diesel particulate filter (CDPF), and a continuously regenerating diesel particulate filter (CR-DPF).

  14. Table 41. No. 2 Diesel Fuel Prices by Sulfur Content, Sales...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    200 Energy Information AdministrationPetroleum Marketing Annual 1999 Table 41. No. 2 Diesel Fuel Prices by Sulfur Content, Sales Type, and PAD District (Cents per Gallon...

  15. Table 41. No. 2 Diesel Fuel Prices by Sulfur Content, Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    200 Energy Information AdministrationPetroleum Marketing Annual 1998 Table 41. No. 2 Diesel Fuel Prices by Sulfur Content, Sales Type, and PAD District (Cents per Gallon...

  16. Lubricant oil consumption effects on diesel exhaust ash emissions using a sulfur dioxide trace technique and thermogravimetry

    E-Print Network [OSTI]

    Plumley, Michael J

    2005-01-01T23:59:59.000Z

    A detailed experimental study was conducted targeting lubricant consumption effects on ,diesel exhaust ash levels using a model year 2002 5.9L diesel engine, high and low Sulfur commercial lubricants, and clean diesel ...

  17. Diesel Emission Control -- Sulfur Effects (DECSE) Program; Phase I Interim Date Report No. 3: Diesel Fuel Sulfur Effects on Particulate Matter Emissions

    SciTech Connect (OSTI)

    DOE; ORNL; NREL; EMA; MECA

    1999-11-15T23:59:59.000Z

    The Diesel Emission Control-Sulfur Effects (DECSE) is a joint government/industry program to determine the impact of diesel fuel sulfur levels on emission control systems whose use could lower emissions of nitrogen oxides (NO{sub x}) and particulate matter (PM) from on-highway trucks in the 2002--2004 model years. Phase 1 of the program was developed with the following objectives in mind: (1) evaluate the effects of varying the level of sulfur content in the fuel on the emission reduction performance of four emission control technologies; and (2) measure and compare the effects of up to 250 hours of aging on selected devices for multiple levels of fuel sulfur content. This interim report covers the effects of diesel fuel sulfur level on particulate matter emissions for four technologies.

  18. Tribological behavior of near-frictionless carbon coatings in high- and low-sulfur diesel fuels.

    SciTech Connect (OSTI)

    Alzoubi, M. F.; Ajayi, O. O.; Eryilmaz, O. L.; Ozturk, O.; Erdemir, A.; Fenske, G.

    2000-01-19T23:59:59.000Z

    The sulfur content in diesel fuel has a significant effect on diesel engine emissions, which are currently subject to environmental regulations. It has been observed that engine particulate and gaseous emissions are directly proportional to fuel sulfur content. With the introduction of low-sulfur fuels, significant reductions in emissions are expected. The process of sulfur reduction in petroleum-based diesel fuels also reduces the lubricity of the fuel, resulting in premature failure of fuel injectors. Thus, another means of preventing injector failures is needed for engines operating with low-sulfur diesel fuels. In this study, the authors evaluated a near-frictionless carbon (NFC) coating (developed at Argonne National Laboratory) as a possible solution to the problems associated with fuel injector failures in low-lubricity fuels. Tribological tests were conducted with NFC-coated and uncoated H13 and 52100 steels lubricated with high- and low- sulfur diesel fuels in a high-frequency reciprocating test machine. The test results showed that the NFC coatings reduced wear rates by a factor of 10 over those of uncoated steel surfaces. In low-sulfur diesel fuel, the reduction in wear rate was even greater (i.e., by a factor of 12 compared to that of uncoated test pairs), indicating that the NFC coating holds promise as a potential solution to wear problems associated with the use of low-lubricity diesel fuels.

  19. A Low-Carbon Fuel Standard for California, Part 1: Technical Analysis

    E-Print Network [OSTI]

    Farrell, Alexander E.; Sperling, Dan

    2007-01-01T23:59:59.000Z

    produced in CA Diesel Ultra-low-sulfur diesel produced in CAbelow) California ultra low sulfur diesel, pathway D2

  20. A Low-Carbon Fuel Standard for California Part 1: Technical Analysis

    E-Print Network [OSTI]

    2007-01-01T23:59:59.000Z

    produced in CA Diesel Ultra-low-sulfur diesel produced in CAbelow) California ultra low sulfur diesel, pathway D2

  1. Development of Ni-based Sulfur Resistant Catalyst for Diesel Reforming

    SciTech Connect (OSTI)

    Gunther Dieckmann

    2006-06-30T23:59:59.000Z

    In order for diesel fuel to be used in a solid oxide fuel cell auxiliary power unit, the diesel fuel must be reformed into hydrogen, carbon monoxide and carbon dioxide. One of the major problems facing catalytic reforming is that the level of sulfur found in low sulfur diesel can poison most catalysts. This report shows that a proprietary low cost Ni-based reforming catalyst can be used to reform a 7 and 50 ppm sulfur containing diesel fuel for over 500 hours of operation. Coking, which appears to be route of catalyst deactivation due to metal stripping, can be controlled by catalyst modifications, introduction of turbulence, and/or by application of an electromagnetic field with a frequency from {approx}50 kHz to 13.56 MHz with field strength greater than about 100 V/cm and more preferably greater about 500 V/cm.

  2. Analysis of Nitro-Polycyclic Aromatic Hydrocarbons in Conventional Diesel and Fischer--Tropsch Diesel Fuel Emissions Using Electron Monochromator-Mass Spectrometry

    SciTech Connect (OSTI)

    Havey, C. D.; McCormick, R. L.; Hayes, R. R.; Dane, A. J.; Voorhees, K. J.

    2006-01-01T23:59:59.000Z

    The presence of nitro-polycyclic aromatic hydrocarbons (NPAHs) in diesel fuel emissions has been studied for a number of years predominantly because of their contribution to the overall health and environmental risks associated with these emissions. Electron monochromator-mass spectrometry (EM-MS) is a highly selective and sensitive method for detection of NPAHs in complex matrixes, such as diesel emissions. Here, EM-MS was used to compare the levels of NPAHs in fuel emissions from conventional (petroleum) diesel, ultra-low sulfur/low-aromatic content diesel, Fischer-Tropsch synthetic diesel, and conventional diesel/synthetic diesel blend. The largest quantities of NPAHs were detected in the conventional diesel fuel emissions, while the ultra-low sulfur diesel and synthetic diesel fuel demonstrated a more than 50% reduction of NPAH quantities when compared to the conventional diesel fuel emissions. The emissions from the blend of conventional diesel with 30% synthetic diesel fuel also demonstrated a more than 30% reduction of the NPAH content when compared to the conventional diesel fuel emissions. In addition, a correlation was made between the aromatic content of the different fuel types and NPAH quantities and between the nitrogen oxides emissions from the different fuel types and NPAH quantities. The EM-MS system demonstrated high selectivity and sensitivity for detection of the NPAHs in the emissions with minimal sample cleanup required.

  3. Investigation of Solid Particle Number Measurement of Engine Emissions

    E-Print Network [OSTI]

    Zheng, Zhongqing

    2012-01-01T23:59:59.000Z

    of the testing. CARB Ultra Low Sulfur Diesel (ULSD) fuel (SResources Board (CARB) ultra low sulfur diesel (ULSD) fuel (

  4. Fast-regenerable sulfur dioxide adsorbents for diesel engine emission control

    DOE Patents [OSTI]

    Li, Liyu [Richland, WA; King, David L [Richland, WA

    2011-03-15T23:59:59.000Z

    Disclosed herein are sorbents and devices for controlling sulfur oxides emissions as well as systems including such sorbents and devices. Also disclosed are methods for making and using the disclosed sorbents, devices and systems. In one embodiment the disclosed sorbents can be conveniently regenerated, such as under normal exhaust stream from a combustion engine, particularly a diesel engine. Accordingly, also disclosed are combustion vehicles equipped with sulfur dioxide emission control devices.

  5. Neutron Imaging of Diesel Particulate Filters

    SciTech Connect (OSTI)

    Strzelec, Andrea [ORNL; Bilheux, Hassina Z [ORNL; FINNEY, Charles E A [ORNL; Daw, C Stuart [ORNL; Foster, Prof. Dave [University of Wisconsin; Rutland, Prof. Christopher J. [University of Wisconsin; Schillinger, Burkhard [FRM-II, Technische Universitaet Munchen; Schulz, Michael [FRM-II, Technische Universitaet Munchen

    2009-01-01T23:59:59.000Z

    This article presents nondestructive neutron computed tomography (nCT) measurements of Diesel Particulate Filters (DPFs) as a method to measure ash and soot loading in the filters. Uncatalyzed and unwashcoated 200cpsi cordierite DPFs exposed to 100% biodiesel (B100) exhaust and conventional ultra low sulfur 2007 certification diesel (ULSD) exhaust at one speed-load point (1500rpm, 2.6bar BMEP) are compared to a brand new (never exposed) filter. Precise structural information about the substrate as well as an attempt to quantify soot and ash loading in the channel of the DPF illustrates the potential strength of the neutron imaging technique.

  6. Near-frictionless carbon coatings for use in fuel injectors and pump systems operating with low-sulfur diesel fuels

    SciTech Connect (OSTI)

    Erdemir, A.; Ozturk, O.; Alzoubi, M.; Woodford, J.; Ajayi, L.; Fenske, G.

    2000-01-19T23:59:59.000Z

    While sulfur in diesel fuels helps reduce friction and prevents wear and galling in fuel pump and injector systems, it also creates environmental pollution in the form of hazardous particulates and SO{sub 2} emissions. The environmental concern is the driving force behind industry's efforts to come up with new alternative approaches to this problem. One such approach is to replace sulfur in diesel fuels with other chemicals that would maintain the antifriction and antiwear properties provided by sulfur in diesel fuels while at the same time reducing particulate emissions. A second alternative might be to surface-treat fuel injection parts (i.e., nitriding, carburizing, or coating the surfaces) to reduce or eliminate failures associated with the use of low-sulfur diesel fuels. This research explores the potential usefulness of a near-frictionless carbon (NFC) film developed at Argonne National Laboratory in alleviating the aforementioned problems. The lubricity of various diesel fuels (i.e., high-sulfur, 500 ppm; low sulfur, 140 ppm; ultra-clean, 3 ppm; and synthetic diesel or Fischer-Tropsch, zero sulfur) were tested by using both uncoated and NFC-coated 52100 steel specimens in a ball-on-three-disks and a high-frequency reciprocating wear-test rig. The test program was expanded to include some gasoline fuels as well (i.e., regular gasoline and indolene) to further substantiate the usefulness of the NFC coatings in low-sulfur gasoline environments. The results showed that the NFC coating was extremely effective in reducing wear and providing lubricity in low-sulfur or sulfur-free diesel and gasoline fuels. Specifically, depending on the wear test rig, test pair, and test media, the NFC films were able to reduce wear rates of balls and flats by factors of 8 to 83. These remarkable reductions in wear rates raise the prospect for using the ultra slick carbon coatings to alleviate problems that will be caused by the use of low sulfur diesel and gasoline fuels. Surfaces of the wear scars and tracks were characterized by optical and scanning electron microscopy, and by Raman spectroscopy.

  7. Multilayer Platform for Ultra-Low-Loss Waveguide Applications

    E-Print Network [OSTI]

    2012-01-01T23:59:59.000Z

    1, 2012 Multilayer Platform for Ultra-Low-Loss Waveguidepreviously demonstrated ultra-low-loss technologies. Groupet al. : MULTILAYER PLATFORM FOR ULTRA-LOW-LOSS WAVEGUIDE

  8. Ultra Low Power Bioelectronics Fundamentals, Biomedical Applications,

    E-Print Network [OSTI]

    Sarpeshkar, Rahul

    Ultra Low Power Bioelectronics Fundamentals, Biomedical Applications, and Bio-inspired Systems to articulate information-based principles for ultra-low-power design that apply to biology or to electronics of ultra- low-power electronics and bioelectronics is shown in the figure below. Engineering can aid

  9. A Lifecycle Emissions Model (LEM): Lifecycle Emissions from Transportation Fuels, Motor Vehicles, Transportation Modes, Electricity Use, Heating and Cooking Fuels, and Materials

    E-Print Network [OSTI]

    Delucchi, Mark

    2003-01-01T23:59:59.000Z

    S and a reference ultra-low-sulfur diesel (ULSD) with 5 ppmof the reference ultra-low-sulfur diesel (5 ppm). SF CD =diesel fuel (CD), ultra-low-sulfur diesel fuel (ULSD),

  10. Analytical Framework to Evaluate Emission Control Systems for Marine Engines

    E-Print Network [OSTI]

    Jayaram, Varalakshmi

    2010-01-01T23:59:59.000Z

    fueled with ultra low sulfur diesel, RME-diesel blends andengine fueled with ultra-low sulfur diesel fuel blended withMaterials B0 Ultra Low Sulfur Diesel B20 20% Biodiesel 80%

  11. Emissions of Transport Refrigeration Units with CARB Diesel, Gas-to-Liquid Diesel, and Emissions Control Devices

    SciTech Connect (OSTI)

    Barnitt, R. A.; Chernich, D.; Burnitzki, M.; Oshinuga, A.; Miyasato, M.; Lucht, E.; van der Merwe, D.; Schaberg, P.

    2010-05-01T23:59:59.000Z

    A novel in situ method was used to measure emissions and fuel consumption of transport refrigeration units (TRUs). The test matrix included two fuels, two exhaust configurations, and two TRU engine operating speeds. Test fuels were California ultra low sulfur diesel and gas-to-liquid (GTL) diesel. Exhaust configurations were a stock muffler and a Thermo King pDPF diesel particulate filter. The TRU engine operating speeds were high and low, controlled by the TRU user interface. Results indicate that GTL diesel fuel reduces all regulated emissions at high and low engine speeds. Application of a Thermo King pDPF reduced regulated emissions, sometimes almost entirely. The application of both GTL diesel and a Thermo King pDPF reduced regulated emissions at high engine speed, but showed an increase in oxides of nitrogen at low engine speed.

  12. Strategies and Technologies for Improving Air Quality Around Ports

    E-Print Network [OSTI]

    Khan, Mohammad Yusuf

    2013-01-01T23:59:59.000Z

    fueled by ultra-low sulfur diesel (ULSD) and operating on afrom burning ultra-low sulfur diesel (ULSD) to a 50/50 blendwhen switching from ultra-low sulfur diesel (ULSD) to A50.

  13. Emissions Benefits From Renewable Fuels and Other Alternatives for Heavy-Duty Vehicles

    E-Print Network [OSTI]

    Hajbabaei, Maryam

    2013-01-01T23:59:59.000Z

    with a 10% aromatic, ultra-low sulfur diesel fuel used inequivalent 10% aromatic ultra-low sulfur diesel fuel used inx emissions compared to ultra-low sulfur diesel fuel (ULSD).

  14. Strategies and Technologies for Improving Air Quality Around Ports

    E-Print Network [OSTI]

    Khan, Mohammad Yusuf

    2013-01-01T23:59:59.000Z

    profile from burning ultra-low sulfur diesel (ULSD) to awhen switching from ultra-low sulfur diesel (ULSD) to A50.emission profile burning ultra low sulfur diesel (ULSD) to a

  15. Renewable Diesel

    Broader source: Energy.gov (indexed) [DOE]

    Renewable Diesel Process Co-feed Renewable Oils to Diesel Hydrotreater 150-2400 psi Hydrogen, 600-800F Normal reaction is sulfur removal (HDS) At HDS Conditions Fat...

  16. Analytical Framework to Evaluate Emission Control Systems for Marine Engines

    E-Print Network [OSTI]

    Jayaram, Varalakshmi

    2010-01-01T23:59:59.000Z

    of Low Sulfur, Ultra Low Sulfur and Biodiesel Blends in a DIengine fueled with ultra low sulfur diesel, RME-dieselengine fueled with ultra-low sulfur diesel fuel blended with

  17. ULTRA-LOW-ENERGY HIGH-CURRENT ION SOURCE

    E-Print Network [OSTI]

    Anders, Andre

    2010-01-01T23:59:59.000Z

    a high current ion source for ultra-low energy ions has beenthe Department of Energy ULTRA-LOW-ENERGY HIGH-CURRENT IONedited by A. Anders. ULTRA-LOW-ENERGY HIGH-CURRENT ION

  18. Investigation of Solid Particle Number Measurement of Engine Emissions

    E-Print Network [OSTI]

    Zheng, Zhongqing

    2012-01-01T23:59:59.000Z

    the testing. CARB Ultra Low Sulfur Diesel (ULSD) fuel (S = 8Board (CARB) ultra low sulfur diesel (ULSD) fuel (S < 15

  19. Nanosegregated Cathode Catalysts with Ultra-Low Platinum Loading...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Nanosegregated Cathode Catalysts with Ultra-Low Platinum Loading Nanosegregated Cathode Catalysts with Ultra-Low Platinum Loading Presented at the Department of Energy Fuel Cell...

  20. Novel Ultra-Low-Energy Consumption Ultrasonic Clothes Dryer ...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Ultra-Low-Energy Consumption Ultrasonic Clothes Dryer Novel Ultra-Low-Energy Consumption Ultrasonic Clothes Dryer Preliminary measured drying time of fabric sample using ultrasonic...

  1. A Lifecycle Emissions Model (LEM): Lifecycle Emissions from Transportation Fuels, Motor Vehicles, Transportation Modes, Electricity Use, Heating and Cooking Fuels, and Materials

    E-Print Network [OSTI]

    Delucchi, Mark

    2003-01-01T23:59:59.000Z

    = distillate fuel; ULSD = ultra-low-sulfur distillate fuel;ppm S and a reference ultra-low-sulfur diesel (ULSD) with 5content of the reference ultra-low-sulfur diesel (5 ppm). SF

  2. Estimating Impacts of Diesel Fuel Reformulation with Vector-based Blending

    SciTech Connect (OSTI)

    Hadder, G.R.

    2003-01-23T23:59:59.000Z

    The Oak Ridge National Laboratory Refinery Yield Model has been used to study the refining cost, investment, and operating impacts of specifications for reformulated diesel fuel (RFD) produced in refineries of the U.S. Midwest in summer of year 2010. The study evaluates different diesel fuel reformulation investment pathways. The study also determines whether there are refinery economic benefits for producing an emissions reduction RFD (with flexibility for individual property values) compared to a vehicle performance RFD (with inflexible recipe values for individual properties). Results show that refining costs are lower with early notice of requirements for RFD. While advanced desulfurization technologies (with low hydrogen consumption and little effect on cetane quality and aromatics content) reduce the cost of ultra low sulfur diesel fuel, these technologies contribute to the increased costs of a delayed notice investment pathway compared to an early notice investment pathway for diesel fuel reformulation. With challenging RFD specifications, there is little refining benefit from producing emissions reduction RFD compared to vehicle performance RFD. As specifications become tighter, processing becomes more difficult, blendstock choices become more limited, and refinery benefits vanish for emissions reduction relative to vehicle performance specifications. Conversely, the emissions reduction specifications show increasing refinery benefits over vehicle performance specifications as specifications are relaxed, and alternative processing routes and blendstocks become available. In sensitivity cases, the refinery model is also used to examine the impact of RFD specifications on the economics of using Canadian synthetic crude oil. There is a sizeable increase in synthetic crude demand as ultra low sulfur diesel fuel displaces low sulfur diesel fuel, but this demand increase would be reversed by requirements for diesel fuel reformulation.

  3. Drive cycle analysis of butanol/diesel blends in a light-duty vehicle.

    SciTech Connect (OSTI)

    Miers, S. A.; Carlson, R. W.; McConnell, S. S.; Ng, H. K.; Wallner, T.; LeFeber, J.; Energy Systems; Esper Images Video & Multimedia

    2008-10-01T23:59:59.000Z

    The potential exists to displace a portion of the petroleum diesel demand with butanol and positively impact engine-out particulate matter. As a preliminary investigation, 20% and 40% by volume blends of butanol with ultra low sulfur diesel fuel were operated in a 1999 Mercedes Benz C220 turbo diesel vehicle (Euro III compliant). Cold and hot start urban as well as highway drive cycle tests were performed for the two blends of butanol and compared to diesel fuel. In addition, 35 MPH and 55 MPH steady-state tests were conducted under varying road loads for the two fuel blends. Exhaust gas emissions, fuel consumption, and intake and exhaust temperatures were acquired for each test condition. Filter smoke numbers were also acquired during the steady-state tests.

  4. The Engineering Meetings Board has approved this paper for publication. It has successfully completed SAE's peer review process under the supervision of the session organizer. This process requires a minimum of three (3) reviews by industry experts.

    E-Print Network [OSTI]

    Wu, Mingshen

    through the use of engine optimization, aftertreatment system integration, and ultra-low sulfur diesel

  5. Catalyzed Diesel Particulate Filter Performance in a Light-Duty Vehicle

    SciTech Connect (OSTI)

    Sluder, C.S.

    2001-04-23T23:59:59.000Z

    Light-duty chassis dynamometer driving cycle tests were conducted on a Mercedes A170 diesel vehicle with various sulfur-level fuels and exhaust emission control systems. Triplicate runs of a modified light-duty federal test procedure (FTP), US06 cycle, and SCO3 cycle were conducted with each exhaust configuration and fuel. Ultra-low sulfur (3-ppm) diesel fuel was doped to 30- and 150-ppm sulfur so that all other fuel properties remained the same. The fuels used in these experiments met the specifications of the fuels from the DECSE (Diesel Emission Control Sulfur Effects) program. Although the Mercedes A170 vehicle is not available in the US, its emissions in the as tested condition fell within the U.S. Tier 1 full useful life standards with the OEM catalysts installed. Tests with the OEM catalysts removed showed that the OEM catalysts reduced PM emissions from the engine-out condition by 30-40% but had negligible effects on NOx emissions. Fuel sulfur level had very little effect on th e OEM catalyst performance. A prototype catalyzed diesel particulate filter (CDPF) mounted in an underfloor configuration reduced particulate matter emissions by more than 90% compared to the factory emissions control system. The results show that the CDPF did not promote any significant amounts of SO{sub 2}-to-sulfate conversion during these light-duty drive cycles.

  6. Ultra-low field magnetic resonance using optically pumped noble gases and SQUID detection

    E-Print Network [OSTI]

    Wong-Foy, Annjoe G.

    2010-01-01T23:59:59.000Z

    Enhancement . . . . Ultra Low Field Xenon NMR ShowingIntroduction.. 4.2 Ultra Low FieldNuclear Polarization 5.10.3 Ultra Low Field Chemical Shift

  7. Ultra-Low Power Time Synchronization Using Passive Radio Receivers

    E-Print Network [OSTI]

    Amir, Yair

    Ultra-Low Power Time Synchronization Using Passive Radio Receivers Yin Chen Qiang Wang Marcus Chang. In this pa- per, we present an inexpensive and ultra-low power ( of elapsed seconds. The universal time sig- nal receiver combines an off-the-shelf radio chip with an ultra-low

  8. American Institute of Aeronautics and Astronautics Ultra Low Emissions Combustor

    E-Print Network [OSTI]

    Seitzman, Jerry M.

    1 American Institute of Aeronautics and Astronautics T Ultra Low Emissions Combustor with Non-premixed modes of combustion with ultra low NOx emissions. The combustor consists of a tube with open and closed low temperatures with ultra low NOx emission in the 1 ppm range and below. It is also shown

  9. Silicon on ultra-low-loss waveguide photonic integration platform

    E-Print Network [OSTI]

    Bauters, Jared; Davenport, Michael; Heck, Martijn; Doylend, Jonathan; Chen, Arnold; Fang, Alexander

    2013-01-01T23:59:59.000Z

    and J. E. Bowers, “Ultra-low-loss high-aspect-ratio Si 3 N 4and K. J. Vahala, “Ultra-low-loss optical delay line on aspiral is 78 mm long. 3. Ultra-low-loss waveguides with and

  10. Universal Hash Functions for Emerging Ultra-Low-Power Networks

    E-Print Network [OSTI]

    Universal Hash Functions for Emerging Ultra-Low-Power Networks Kaan Y¨uksel, Jens-Peter Kaps provable security in ultra-low-power applications such as the next generation self-powered sensor networks in ultra-low-power applications such as "Smart Dust" motes and RFIDs. By virtue of their security

  11. Ultra Low Power Electronics for Medicine Rahul Sarpeshkar

    E-Print Network [OSTI]

    Sarpeshkar, Rahul

    Ultra Low Power Electronics for Medicine Rahul Sarpeshkar Analog VLSI and Biological Systems Group on an implanted 100mAh rechargeable battery. Another example includes an ultra low power portable pulse oximeter monitoring. Medical applications in the future are likely to benefit greatly from ultra low power electronics

  12. AERODYNAMICS AND DESIGN FOR ULTRA-LOW REYNOLDS NUMBER FLIGHT

    E-Print Network [OSTI]

    Stanford University

    AERODYNAMICS AND DESIGN FOR ULTRA-LOW REYNOLDS NUMBER FLIGHT A DISSERTATION SUBMITTED at Reynolds numbers below 10,000, here termed ultra-low Reynolds numbers. The effects of airfoil geometry at ultra-low Reynolds numbers. To further explore this design space, the flow solver has been coupled

  13. Adaptive Injection Strategies (AIS) for Ultra-low Emissions Diesel...

    Broader source: Energy.gov (indexed) [DOE]

    * Motivation and background * Adaptive Injection Strategy (AIS) * Simulation and optimization - Two-Stage Combustion (TSC -- HCCI + Diffusion combustion) optimization using AIS...

  14. Environmental implications of trade liberalization on North American transport services: the case of the trucking sector

    E-Print Network [OSTI]

    Fernandez, Linda

    2010-01-01T23:59:59.000Z

    requires the use of ultra low-sulfur diesel, now required inthe shift toward ultra low-sulfur fuel. The nationwide plan

  15. InsideIllinoisFeb. 20, 2014 Vol. 33, No. 15

    E-Print Network [OSTI]

    Lewis, Jennifer

    in transportation fuels ­ diesel, for ex- ample ­ that can be blended with exist- ing ultra-low-sulfur diesels

  16. A NMR-Based Carbon-Type Analysis of Diesel Fuel Blends From Various Sources

    SciTech Connect (OSTI)

    Bays, J. Timothy; King, David L.

    2013-05-10T23:59:59.000Z

    In collaboration with participants of the Coordinating Research Council (CRC) Advanced Vehicle/Fuels/Lubricants (AVFL) Committee, and project AVFL-19, the characteristics of fuels from advanced and renewable sources were compared to commercial diesel fuels. The main objective of this study was to highlight similarities and differences among the fuel types, i.e. ULSD, renewables, and alternative fuels, and among fuels within the different fuel types. This report summarizes the carbon-type analysis from 1H and 13C{1H} nuclear magnetic resonance spectroscopy (NMR) of 14 diesel fuel samples. The diesel fuel samples come from diverse sources and include four commercial ultra-low sulfur diesel fuels (ULSD), one gas-to-liquid diesel fuel (GTL), six renewable diesel fuels (RD), two shale oil-derived diesel fuels, and one oil sands-derived diesel fuel. Overall, the fuels examined fall into two groups. The two shale oil-derived samples and the oil-sand-derived sample closely resemble the four commercial ultra-low sulfur diesels, with SO1 and SO2 most closely matched with ULSD1, ULSD2, and ULSD4, and OS1 most closely matched with ULSD3. As might be expected, the renewable diesel fuels, with the exception of RD3, do not resemble the ULSD fuels because of their very low aromatic content, but more closely resemble the gas-to-liquid sample (GTL) in this respect. RD3 is significantly different from the other renewable diesel fuels in that the aromatic content more closely resembles the ULSD fuels. Fused-ring aromatics are readily observable in the ULSD, SO, and OS samples, as well as RD3, and are noticeably absent in the remaining RD and GTL fuels. Finally, ULSD3 differs from the other ULSD fuels by having a significantly lower aromatic carbon content and higher cycloparaffinic carbon content. In addition to providing important comparative compositional information regarding the various diesel fuels, this report also provides important information about the capabilities of NMR spectroscopy for the detailed characterization and comparison of fuels and fuel blends.

  17. November 30, 2006 -TCAT to put six hybrid buses on the road Home News Opinion Accent Sports Click. Exclusively Online

    E-Print Network [OSTI]

    be using an ultra-low-sulfur diesel fuel that is being phased in nationally starting this fall. Sulfur

  18. Paper 2008-01-0434 Effects of Sulfur Level and Anisotropy of Sulfide Inclusions on

    E-Print Network [OSTI]

    Fatemi, Ali

    to fatigue strength, the high sulfur material had up to 25% lower fatigue strength than the ultra low sulfur, monotonic tensile and CVN impact behavior of SAE 4140 steel with high (0.077% S), low (0.012% S) and ultra low (0.004% S) sulfur contents at two hardness levels (40 HRC and 50 HRC). The longitudinally oriented

  19. Method to improve lubricity of low-sulfur diesel and gasoline fuels

    DOE Patents [OSTI]

    Erdemir, Ali

    2004-08-31T23:59:59.000Z

    A method for providing lubricity in fuels and lubricants includes adding a boron compound to a fuel or lubricant to provide a boron-containing fuel or lubricant. The fuel or lubricant may contain a boron compound at a concentration between about 30 ppm and about 3,000 ppm and a sulfur concentration of less than about 500 ppm. A method of powering an engine to minimize wear, by burning a fuel containing boron compounds. The boron compounds include compound that provide boric acid and/or BO.sub.3 ions or monomers to the fuel or lubricant.

  20. Effect of Biodiesel Blending on the Speciation of Soluble Organic Fraction from a Light Duty Diesel Engine

    SciTech Connect (OSTI)

    Strzelec, Andrea [ORNL] [ORNL; Storey, John Morse [ORNL] [ORNL; Lewis Sr, Samuel Arthur [ORNL] [ORNL; Daw, C Stuart [ORNL] [ORNL; Foster, Prof. Dave [University of Wisconsin] [University of Wisconsin; Rutland, Prof. Christopher J. [University of Wisconsin] [University of Wisconsin

    2010-01-01T23:59:59.000Z

    Soy methyl ester (SME) biodiesel was volumetrically blended with 2007 certification ultra low sulfur diesel (ULSD) fuel and run in a 1.7L direct-injection common rail diesel engine at one speed-load point (1500rpm, 2.6bar BMEP). Engine fueling rate and injection timing were adjusted to maintain a constant load, while particulate samples were collected in a diesel particulate filter (DPF) and with a dilution tunnel sampling train. The samples collected at these two locations were found to contain different levels of soluble organic fraction (SOF) and the different hydrocarbon species in the SOF. This observation indicates that traditional SOF measurements, in light of the specific sampling procedure used, may not be appropriate to DPF applications.

  1. Digital Bimodal Function: An Ultra-Low Energy Security Primitive

    E-Print Network [OSTI]

    Potkonjak, Miodrag

    Digital Bimodal Function: An Ultra-Low Energy Security Primitive Teng Xu, James B. Wendt function (DBF) that enables ultra low energy security protocols. DBF allows the computation of legitimate and energy expense. Our new approach is competitive with the energy efficiency of traditional security key

  2. Matched Public PUF: Ultra Low Energy Security Platform

    E-Print Network [OSTI]

    Potkonjak, Miodrag

    Matched Public PUF: Ultra Low Energy Security Platform Saro Meguerdichian and Miodrag Potkonjak that cannot be matched with any third such module. Each device enables rapid, low-energy computation of ultra Our strategic objective is to introduce concepts and a hard- ware platform that enable ultra low power

  3. One-dimensional ordering of ultra-low density ion beams in a storage ring

    E-Print Network [OSTI]

    Okamoto, H.; Okabe, K.; Yuri, Y.; Mohl, D.; Sessler, A.M.

    2004-01-01T23:59:59.000Z

    One-dimensional ordering of ultra-low density ion beams in ais applicable to an ultra-low density beam where collectiveabout 10 cm. In such an ultra-low density regime, no collec-

  4. Ultra-Low-Power Adder Stage Design for Exascale Floating Point Units

    E-Print Network [OSTI]

    Del Barrio, AA; Bagherzadeh, N; Hermida, R

    2014-01-01T23:59:59.000Z

    date: March 2014. Ultra-Low-Power Adder Stage Design fordate: March 2014. Ultra-Low-Power Adder Stage Design fordate: March 2014. Ultra-Low-Power Adder Stage Design for

  5. Development of a combustion technology for ultra-low emission (< 5 ppm nox) industrial burner

    E-Print Network [OSTI]

    Littlejohn, D.; Majeski, A.J.; Cheng, R.K.; Castaldini, C.

    2002-01-01T23:59:59.000Z

    Investigation of an Ultra-Low NO x Premixed CombustionInvestigation of an Ultra-Low NO x Premixed Combustioncombustion concept to achieve ultra-low emissions (NO x ? 2

  6. Ultra-low-loss high-aspect-ratio Si3N4 wavequides

    E-Print Network [OSTI]

    2011-01-01T23:59:59.000Z

    R. Gao, and A. Garito, “Ultra-Low-Loss Polymer Waveguides,”Ultra-low-loss high-aspect-ratio Si 3 N 4 waveguides Jaredan approach to make ultra-low-loss waveguides using stable

  7. Ultra-low field MRI of prostate cancer using SQUID detection

    E-Print Network [OSTI]

    Busch, Sarah Elizabeth

    2011-01-01T23:59:59.000Z

    coil. Chapter 3 3 Ultra low field MRI 3.1 Polarization TheUltra-low field MRI of prostate cancer using SQUID detectionSteven Conolly Spring 2011 Ultra-low field MRI of prostate

  8. Quadrature Rotating-Frame Gradient Fields for Ultra-Low Field Nuclear Magnetic Resonance and Imaging

    E-Print Network [OSTI]

    Bouchard, Louis-Serge

    2005-01-01T23:59:59.000Z

    Frame Gradient Fields For Ultra-Low Field Nuclear Magneticslow, as in the limit of ultra-low ?elds. In the ?rst case,B. Slice selection in ultra-low ?elds We ?rst examine the

  9. Electrical activation and spin coherence of ultra low dose antimony implants in silicon

    E-Print Network [OSTI]

    2005-01-01T23:59:59.000Z

    and spin coherence of ultra low dose antimony implants inClara, CA 95054 We implanted ultra low doses (0.2 to 2×10 11100 nm, corresponding to ultra low ion implantation doses of

  10. Diesel Fueled SOFC for Class 7/Class 8 On-Highway Truck Auxiliary Power

    SciTech Connect (OSTI)

    Vesely, Charles John-Paul [Cummins Power Generation; Fuchs, Benjamin S. [Cummins Power Generation; Booten, Chuck W. [Protonex Technology, LLC

    2010-03-31T23:59:59.000Z

    The following report documents the progress of the Cummins Power Generation (CPG) Diesel Fueled SOFC for Class 7/Class 8 On-Highway Truck Auxiliary Power (SOFC APU) development and final testing under the U.S. Department of Energy (DOE) Energy Efficiency and Renewable Energy (EERE) contract DE-FC36-04GO14318. This report overviews and summarizes CPG and partner development leading to successful demonstration of the SOFC APU objectives and significant progress towards SOFC commercialization. Significant SOFC APU Milestones: Demonstrated: Operation meeting SOFC APU requirements on commercial Ultra Low Sulfur Diesel (ULSD) fuel. SOFC systems operating on dry CPOX reformate. Successful start-up and shut-down of SOFC APU system without inert gas purge. Developed: Low cost balance of plant concepts and compatible systems designs. Identified low cost, high volume components for balance of plant systems. Demonstrated efficient SOFC output power conditioning. Demonstrated SOFC control strategies and tuning methods.

  11. Impact of Biodiesel on the Oxidation Kinetics and Morphology of Diesel Particulate

    SciTech Connect (OSTI)

    Strzelec, Andrea [ORNL] [ORNL; Toops, Todd J [ORNL] [ORNL; Daw, C Stuart [ORNL] [ORNL

    2011-01-01T23:59:59.000Z

    We compare the oxidation characteristics of four different diesel particulates generated with a modern light-duty engine. The four particulates represent engine fueling with conventional ultra-low sulfur diesel (ULSD), biodiesel, and two intermediate blends of these fuels. The comparisons discussed here are based on complementary measurements implemented in a laboratory micro-reactor, including temperature programmed desorption and oxidation, pulsed isothermal oxidation, and BET surface area. From these measurements we have derived models that are consistent with the observed oxidation reactivity differences. When accessible surface area effects are properly accounted for, the oxidation kinetics of the fixed carbon components were found to consistently exhibit an Arrhenius activation energy of 113 6 kJ/mol. Release of volatile carbon from the as-collected particulate appears to follow a temperaturedependent rate law.

  12. Field Demonstration of High Efficiency Ultra-Low-Temperature...

    Broader source: Energy.gov (indexed) [DOE]

    Ultra-low temperature laboratory freezers (ULTs) are some of the most energy-intensive pieces of equipment in a scientific research laboratory, yet there are several barriers to...

  13. Charge pumping techniques in ultra-low current transconductor design 

    E-Print Network [OSTI]

    Becker-Gomez, Adriana

    2002-01-01T23:59:59.000Z

    The purpose of this thesis is to introduce the use of interface-trap charge pumping devices (ITCP) in an analog application based in ultra-low-current transconductors. This application naturally exploits the continuous nature of the current...

  14. An Advanced Ultra-Low Temperature Scanning Probe Microscope

    E-Print Network [OSTI]

    An Advanced Ultra-Low Temperature Scanning Probe Microscope P R O J E C T L E A D E R : Joseph); Steven Blankenship, Alan Band (NIST) G O A L To develop an ultra-high vacuum, ultra-low temperature, high of subpicometer stability and can operate in ultra-high vacuum at 10 mK, and in magnetic fields up to 15 T

  15. Ultra-low velocities and Superplumes Garnero, Thorne, McNamara, Rost [2005

    E-Print Network [OSTI]

    Garnero, Ed

    Ultra-low velocities and Superplumes Garnero, Thorne, McNamara, Rost [2005] - 1- Fine-scale ultra-low, Arizona 85287-1404 USA Abstract. Ultra-low velocity layering at Earth's core-mantle boundary has now been in the overlying few hundred km of the mantle. Ultra-low velocity zones contain properties consistent with partial

  16. An Ultra-Low-Power Analog Memory System with an Adaptive Sampling Rate

    E-Print Network [OSTI]

    Graham, David W.

    An Ultra-Low-Power Analog Memory System with an Adaptive Sampling Rate Brandon M. Kelly, Brandon normally associated with sleep states in WSNs, we introduce an ultra-low-power analog memory buffer in which ultra- low-power operation is a necessity. In this paper, we propose an ultra-low-power analog mem

  17. Requirements for Emergency Generator Operation All Emergency Generators

    E-Print Network [OSTI]

    Lawson, Catherine L.

    .2% Sulfur or less) As of October 1, 2007 Ultra low Sulfur Diesel must be used (0.05% Sulfur or less be received from manufacturer and sent to REHS Diesel emergency Generators must use low Sulfur Diesel ( 0

  18. COMPARISON OF CLEAN DIESEL BUSES TO CNG BUSES

    SciTech Connect (OSTI)

    Lowell, D.; Parsley, W.; Bush,C; Zupo, D.

    2003-08-24T23:59:59.000Z

    Using previously published data on regulated and unregulated emissions, this paper will compare the environmental performance of current generation transit buses operated on compressed natural gas (CNG) to current generation transit buses operated on ultra low sulfur diesel fuel (ULSD) and incorporating diesel particulate filters (DPF). Unregulated emissions evaluated include toxic compounds associated with adverse health effects (carbonyl, PAH, NPAH, benzene) as well as PM particle count and size distribution. For all regulated and unregulated emissions, both technologies are shown to be comparable. DPF equipped diesel buses and CNG buses have virtually identical levels of PM mass emissions and particle number emissions. DPF-equipped diesel buses have lower HC and CO emissions and lower emissions of toxic substances such as benzene, carbonyls and PAHs than CNG buses. CNG buses have lower NOx emissions than DPF-equipped buses, though CNG bus NOx emissions are shown to be much more variable. In addition, this paper will compare the capital and operating costs of CNG and DPF-equipped buses. The cost comparison is primarily based on the experience of MTA New York City Transit in operating CNG buses since 1995 and DPF-equipped buses fueled with ULSD since 2001. Published data on the experience of other large transit agencies in operating CNG buses is used to validate the NYCT experience. The incremental cost (compared to ''baseline'' diesel) of operating a typical 200-bus depot is shown to be six times higher for CNG buses than for ''clean diesel'' buses. The contributors to this increased cost for CNG buses are almost equally split between increased capital costs for purchase of buses and installation of fueling infrastructure, and increased operating costs for purchase of fuel, bus maintenance, and fuel station maintenance.

  19. Low-voltage ultra-low-poweranalog IC design -djmamic translinearcircuits 1.3.1 1.3 Low-voltage ultra-low-power analog IC design

    E-Print Network [OSTI]

    Serdijn, Wouter A.

    Low-voltage ultra-low-poweranalog IC design -djmamic translinearcircuits 1.3.1 1.3 Low-voltage ultra-low-power analog IC design -dynamic translinear circuits 0 (rg G x m .- E . . . . . a r, a" P, 44' s" +N m - _ c o3 #12;Low-voltage ultra-low-power analog IC design -dynamic translinear circuits I

  20. 9th Diesel Engine Emissions Reduction (DEER) Workshop 2003

    SciTech Connect (OSTI)

    Kukla, P; Wright, J; Harris, G; Ball, A; Gu, F

    2003-08-24T23:59:59.000Z

    The PowerTrap{trademark} is a non-exhaust temperature dependent system that cannot become blocked and features a controlled regeneration process independent of the vehicle's drive cycle. The system has a low direct-current power source requirement available in both 12-volt and 24-volt configurations. The system is fully programmable, fully automated and includes Euro IV requirements of operation verification. The system has gained European component-type approval and has been tested with both on- road and off-road diesel fuel up to 2000 parts per million. The device is fail-safe: in the event of a device malfunction, it cannot affect the engine's performance. Accumulated mileage testing is in excess of 640,000 miles to date. Vehicles include London-type taxicabs (Euro 1 and 2), emergency service fire engines (Euro 1, 2, and 3), inner city buses, and light-duty locomotives. Independent test results by Shell Global Solutions have consistently demonstrated 85-99 percent reduction of ultrafines across the 7-35 nanometer size range using a scanning mobility particle sizer with both ultra-low sulfur diesel and off-road high-sulfur fuel.

  1. Spintronic switches for ultra low energy global interconnects

    SciTech Connect (OSTI)

    Sharad, Mrigank, E-mail: msharad@purdue.edu; Roy, Kaushik [School of Electrical and Computer Engineering, Purdue University, West Lafayette, Indiana 47907 (United States)

    2014-05-07T23:59:59.000Z

    We present ultra-low energy interconnect design using nano-scale spin-torque (ST) switches for global data-links. Emerging spin-torque phenomena can lead to ultra-low-voltage, high-speed current-mode magnetic-switches. ST-switches can simultaneously provide large trans-impedance gain by employing magnetic tunnel junctions, to convert current-mode signals into large-swing voltage levels. Such device-characteristics can be used in the design of energy-efficient current-mode global interconnects.

  2. SERVICE STATION INFORMATION There are 2 campus service stations for use by University of Michigan vehicles. The Baxter Road Service

    E-Print Network [OSTI]

    Kirschner, Denise

    to alternative fuel by refining our biodiesel fuel to Ultra Low Sulfur B20 biodiesel meeting 2009 diesel fuel

  3. Project Sponsor: Siemens Power GenerationUCI Combustion Laboratory www.ucicl.uci.edu

    E-Print Network [OSTI]

    Mease, Kenneth D.

    in ultra low sulfur diesel fuel (DF2), its discrete water droplet size distribution and the injection

  4. January2013Update Growing Together

    E-Print Network [OSTI]

    Kim, Philip

    , electric or ultra-low sulfur diesel fuel equipment, and the washing of truck undercarriages and wheels

  5. FUEL FORMULATION EFFECTS ON DIESEL FUEL INJECTION, COMBUSTION, EMISSIONS AND EMISSION CONTROL

    SciTech Connect (OSTI)

    Boehman, A; Alam, M; Song, J; Acharya, R; Szybist, J; Zello, V; Miller, K

    2003-08-24T23:59:59.000Z

    This paper describes work under a U.S. DOE sponsored Ultra Clean Fuels project entitled ''Ultra Clean Fuels from Natural Gas,'' Cooperative Agreement No. DE-FC26-01NT41098. In this study we have examined the incremental benefits of moving from low sulfur diesel fuel and ultra low sulfur diesel fuel to an ultra clean fuel, Fischer-Tropsch diesel fuel produced from natural gas. Blending with biodiesel, B100, was also considered. The impact of fuel formulation on fuel injection timing, bulk modulus of compressibility, in-cylinder combustion processes, gaseous and particulate emissions, DPF regeneration temperature and urea-SCR NOx control has been examined. The primary test engine is a 5.9L Cummins ISB, which has been instrumented for in-cylinder combustion analysis and in-cylinder visualization with an engine videoscope. A single-cylinder engine has also been used to examine in detail the impacts of fuel formulation on injection timing in a pump-line-nozzle fueling system, to assist in the interpretation of results from the ISB engine.

  6. Method for Determining Performance of Sulfur Oxide Adsorbents...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Method for Determining Performance of Sulfur Oxide Adsorbents for Diesel Emission Control Using Online Measurement of SO2 and Method for Determining Performance of Sulfur Oxide...

  7. 7 -29 nm 29 -56 nm 56 -95 nm Particlenumberconcentration(#cm-3

    E-Print Network [OSTI]

    Holmén, Britt A.

    Diesel Buses Using UltraUsing Ultra--low Sulfur Diesellow Sulfur Diesel Aura C. Dávila and Britt A.4 miles ·Average speed: 30 mph · Fuel: ·Ultra-low sulfur diesel (ULSD) ConclusionsConclusions ELPI. · Heavy-duty vehicles contribute one quarter of PM emissions from mobile sources.(1) · Using ultra-low

  8. High-Efficiency, Ultra-Low Emission Combustion in a Heavy-Duty...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency, Ultra-Low Emission Combustion in a Heavy-Duty Engine via Fuel Reactivity Control High-Efficiency, Ultra-Low Emission Combustion in a Heavy-Duty Engine via Fuel...

  9. Low-Temperature Combustion for High-Efficiency, Ultra-Low Emission...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Low-Temperature Combustion for High-Efficiency, Ultra-Low Emission Engines Low-Temperature Combustion for High-Efficiency, Ultra-Low Emission Engines Presentation given at DEER...

  10. Tracking deep mantle reservoirs with ultra-low velocity zones Allen K. McNamara a,

    E-Print Network [OSTI]

    Rhoads, James

    Tracking deep mantle reservoirs with ultra-low velocity zones Allen K. McNamara a, , Edward J, that directly overlies the core-mantle boundary (CMB). These regions have been dubbed Ultra-Low Velocity Zones. Introduction For over 15 yrs seismologists have mapped regions of ultra-low P- and S-wave velocities

  11. SAFETY EFFECTIVENESS OF STOP CONTROL AT ULTRA-LOW VOLUME UNPAVED INTERSECTIONS

    E-Print Network [OSTI]

    Carriquiry, Alicia

    SAFETY EFFECTIVENESS OF STOP CONTROL AT ULTRA-LOW VOLUME UNPAVED INTERSECTIONS Corresponding Author,494 #12;Souleyrette, Tenges, McDonald, Maze, Carriquiry 1 SAFETY EFFECTIVENESS OF STOP CONTROL AT ULTRA-LOW regression and hierarchical Poisson estimation. For ultra-low volume intersections, under 150 vehicles per

  12. Centralized Routing Protocol for Wireless Sensor Networks with Ultra Low Duty Cycle to Achieve Maximum Lifetime

    E-Print Network [OSTI]

    Bahk, Saewoong

    Centralized Routing Protocol for Wireless Sensor Networks with Ultra Low Duty Cycle to Achieve performance because most of them are designed without considering a ultra low duty cycled environment to improve a network lifetime and a routing maintenance cost. We explain the issues of a ultra low duty

  13. Challenge: Ultra-Low-Power Energy-Harvesting Active Networked Tags (EnHANTs)

    E-Print Network [OSTI]

    Zussman, Gil

    Challenge: Ultra-Low-Power Energy-Harvesting Active Networked Tags (EnHANTs) Maria Gorlatova, Peter posed by a new class of ultra-low-power devices referred to as Energy-Harvesting Ac- tive Networked Tags), and determining locations of disaster sur- vivors. Recent advances in ultra-low-power wireless communica- tions

  14. ULTRA LOW PRESSURE-DROP HELIUM-COOLED POROUS-TUNGSTEN PFC S. Sharafat1

    E-Print Network [OSTI]

    Ghoniem, Nasr M.

    ULTRA LOW PRESSURE-DROP HELIUM-COOLED POROUS-TUNGSTEN PFC S. Sharafat1 , A. Mills1 , D. Youchison2/s. Based on these impressive performance results, a unique and scalable heat exchanger channel with ultra-low and ultra low-pressure drop short flow-path (SOFIT) concept was designed. Typical pressure drops through

  15. Integrated Ultra-Low-Loss 4-Bit Tunable Delay for Broadband Phased Array Antenna Applications

    E-Print Network [OSTI]

    2013-01-01T23:59:59.000Z

    F. Bauters, et al. , “Ultra-low-loss high-aspect-ratio Si3N4JUNE 15, 2013 Integrated Ultra-Low-Loss 4-Bit Tunable Delaya 4-bit tunable delay in an ultra-low-loss Si 3 N 4 planar

  16. LP3853/LP3856 3A Fast Response Ultra Low Dropout Linear Regulators

    E-Print Network [OSTI]

    Berns, Hans-Gerd

    LP3853/LP3856 3A Fast Response Ultra Low Dropout Linear Regulators General Description The LP3853/LP3856 series of fast ultra low-dropout linear regulators operate from a +2.5V to +7.0V input supply. Wide range of preset output voltage options are available. These ultra low dropout linear regulators

  17. Suppressing Multi-Channel Ultra-Low-Field MRI Measurement Noise Using Data Consistency and Image

    E-Print Network [OSTI]

    Suppressing Multi-Channel Ultra-Low-Field MRI Measurement Noise Using Data Consistency and Image of Mathematics, National Taiwan University, Taipei, Taiwan, 4 Elekta Oy, Helsinki, Finland Abstract Ultra-low. (2013) Suppressing Multi-Channel Ultra-Low-Field MRI Measurement Noise Using Data Consistency and Image

  18. Aerodynamic Shape Optimization of Airfoils in Ultra-Low Reynolds Number Flow using

    E-Print Network [OSTI]

    Stanford University

    Aerodynamic Shape Optimization of Airfoils in Ultra-Low Reynolds Number Flow using Simultaneous;Aerodynamic Shape Optimization of Airfoils in Ultra-Low Reynolds Number Flow using Simultaneous Pseudo Abstract. The paper presents numerical results of optimized airfoils at ultra-low Reynolds numbers

  19. Fluctuation-induced dynamics of multiphase liquid jets with ultra-low interfacial tension

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Fluctuation-induced dynamics of multiphase liquid jets with ultra-low interfacial tension Alban with an ultra-low interfacial tension presents new opportunities to the control of flow morphologies perturbation; this demonstrates the importance of the inertial effects in flow control at ultra-low interfacial

  20. Energy Efficient Routing Protocol for Wireless Sensor Networks with Ultra Low Duty Cycle

    E-Print Network [OSTI]

    Bahk, Saewoong

    Energy Efficient Routing Protocol for Wireless Sensor Networks with Ultra Low Duty Cycle Wooguil of high energy consumption mainly caused by the clock drift in ultra low duty cycled environments because most of them are designed without considering ultra low duty cycled environments. To achieve

  1. An Ultra Low Power SIMD Processor for Wireless Devices , Sangwon Seo1

    E-Print Network [OSTI]

    Kambhampati, Subbarao

    An Ultra Low Power SIMD Processor for Wireless Devices Mark Woh1 , Sangwon Seo1 , Chaitali, Tempe, AZ {mwoh,swseo,mahlke,tnm}@umich.edu chaitali@asu.edu ABSTRACT This paper presents an ultra low executed. For ultra low power operation, we advocate operating the processor at near threshold volt- age

  2. Pipeline Strategy for Improving Optimal Energy Efficiency in Ultra-Low Voltage Design

    E-Print Network [OSTI]

    Kambhampati, Subbarao

    Pipeline Strategy for Improving Optimal Energy Efficiency in Ultra-Low Voltage Design Mingoo Seok for the ultra low voltage regime. Based on an analytical model and simulations, we propose a pipelining technique that provides higher energy effi- ciency and performance than conventional approaches to ultra low

  3. Effectiveness of Ultra-Low Volume Nighttime Applications of an Adulticide against Diurnal Aedes

    E-Print Network [OSTI]

    Effectiveness of Ultra-Low Volume Nighttime Applications of an Adulticide against Diurnal Aedes and dengue. Vector control programs rarely attempt to suppress this diurnal species with an ultra-low volume, Gaugler R, Fonseca DM (2012) Effectiveness of Ultra-Low Volume Nighttime Applications of an Adulticide

  4. Invited Paper Ultra-low-power Electronics for Non-invasive

    E-Print Network [OSTI]

    Sarpeshkar, Rahul

    Invited Paper Ultra-low-power Electronics for Non-invasive Medical Monitoring L. Turicchia1 , S on the monitoring of the heart--because of its importance--and we describe a micropower electrocardiograph, an ultra-low-power pulse oximeter, an ultra-low-power phonocardiograph, an integrated- circuit switched-capacitor model

  5. An Ultra Low Power CMOS pA/V Transconductor and its Application to Wavelet Filters

    E-Print Network [OSTI]

    Serdijn, Wouter A.

    An Ultra Low Power CMOS pA/V Transconductor and its Application to Wavelet Filters Peterson R topologies of ultra low-power CMOS triode transconductor are proposed. Its input transistors are kept with an extremely small transconductance gm is needed. This paper presents two topologies of ultra low

  6. Telos: Enabling Ultra-Low Power Wireless Research Joseph Polastre, Robert Szewczyk, and David Culler

    E-Print Network [OSTI]

    Culler, David E.

    Telos: Enabling Ultra-Low Power Wireless Research Joseph Polastre, Robert Szewczyk, and David,szewczyk,culler}@cs.berkeley.edu Abstract-- We present Telos, an ultra low power wireless sensor module ("mote") for research and 128kB of flash), extensive sensor interfaces (8 analog lines, several digital IO Fig. 1. Telos ultra-low

  7. Ultra-Low Power DLMS Adaptive Filter For Hearing Aid Applications

    E-Print Network [OSTI]

    Kim, Chris H.

    Ultra-Low Power DLMS Adaptive Filter For Hearing Aid Applications Hyung-il Kim Purdue University, USA +1-765-494-2361 kaushik@ecn.purdue.edu ABSTRACT We present an ultra-low power DLMS (delayed least suitable application areas for sub-threshold logic since ultra-low power consumption takes first priority

  8. An ultra-low voltage high gain operational transconductance amplifier for biomedical

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    An ultra-low voltage high gain operational transconductance amplifier for biomedical applications that work at ultra low voltage power supply. Moreover, low power dissipation is essential in these systems dissipation is also proposed in [5]. Differential pairs are commonly used as input stages, in an ultra-low

  9. An Ultra-Low-Power Human Body Motion Sensor Using Static Electric Field Sensing

    E-Print Network [OSTI]

    Hunt, Galen

    An Ultra-Low-Power Human Body Motion Sensor Using Static Electric Field Sensing Gabe Cohn1 an ultra-low-power method for pas- sively sensing body motion using static electric fields by measuring to infer the amount and type of body motion anywhere on the body and demonstrate an ultra-low-power motion

  10. Performance of plasma sputtered Fuel Cell electrodes with ultra-low Pt M. Cavarroca

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Performance of plasma sputtered Fuel Cell electrodes with ultra-low Pt loadings M. Cavarroca , A. Abstract Ultra-low Pt content PEMFC electrodes have been manufactured using magnetron co- sputtering cell; Plasma sputtering deposition; ultra low platinum loading * Corresponding author: Fax: +33 2 38 41

  11. Variation-aware Clock Network Design Methodology for Ultra-Low Voltage (ULV) Circuits

    E-Print Network [OSTI]

    Lim, Sung Kyu

    Variation-aware Clock Network Design Methodology for Ultra-Low Voltage (ULV) Circuits Xin Zhao networks for ultra-low voltage (ULV) circuits. We show that both clock slew and skew play important roles) at comparable or even higher Fmax compared with the existing methods. Keywords--clock network design, ultra-low

  12. Efficient Concomitant and Remanence Field Artifact Reduction in Ultra-Low-Field MRI Using a

    E-Print Network [OSTI]

    Efficient Concomitant and Remanence Field Artifact Reduction in Ultra-Low-Field MRI Using: For ultra-low-field MRI, the spatial-encoding mag- netic fields generated by gradient coils can have strong to pre-polarize magnetization can improve the signal-to-noise ratio of ultra- low-field MRI. Yet

  13. Ultra-Low Wearing Nanocomposites-How Low Can We Go? Angela Pitenis

    E-Print Network [OSTI]

    Roy, Subrata

    Ultra-Low Wearing Nanocomposites- How Low Can We Go? Angela Pitenis You know more about tribology), this new material, a nanocomposite, is able to achieve ultra-low wear (k~7x10-8 mm3 /(Nm)). This means limits of this ultra-low wearing nanocomposite. Our most recent experiments were conducted in a broad

  14. Bulk CMOS Device Optimization for High-Speed and Ultra-Low Power Operations

    E-Print Network [OSTI]

    Nyathi, Jabulani

    Bulk CMOS Device Optimization for High-Speed and Ultra-Low Power Operations Brent Bero and Jabulani- Interest in subthreshold design has increased due to the emergence of systems that require ultra-low power creating a clear divide between designing for high speed and ultra-low power. It might be beneficial

  15. A Hybrid Adiabatic Content Addressable Memory for Ultra Low-Power Applications

    E-Print Network [OSTI]

    Tessier, Russell

    A Hybrid Adiabatic Content Addressable Memory for Ultra Low-Power Applications Aiyappan Natarajan/write operation. The adiabatic CAM is suitable for ultra low-power, low per- formance applications such as smart, Performance Keywords Ultra-low power, Energy recovery, adiabatic switching 1. INTRODUCTION Content Addressable

  16. Environmental fate model for ultra-low-volume insecticide applications used for adult mosquito management

    E-Print Network [OSTI]

    Peterson, Robert K. D.

    Environmental fate model for ultra-low-volume insecticide applications used for adult mosquito T S No model can accurately predict deposition of insecticides applied with ultra-low-volume technology of insecticides. We develop a validated model to predict the deposition of insecticides after ultra-low

  17. Cryptography for Ultra-Low Power Devices Jens-Peter Kaps

    E-Print Network [OSTI]

    Cryptography for Ultra-Low Power Devices by Jens-Peter Kaps A Dissertation Submitted to the Faculty classify them as ultra-low power devices. Early sensor nodes used simple 8-bit microprocessors to implement of cryptographic algorithms tailored for ultra-low power applications. The goal of this dissertation is to de

  18. Heat capacity of adsorbed Helium-3 at ultra-low temperatures

    E-Print Network [OSTI]

    Boyer, Edmond

    Heat capacity of adsorbed Helium-3 at ultra-low temperatures J. Elbs, C. Winkelmann, Yu. M. Bunkov of monolayers of 3He adsorbed on the surface of a cell filled with superfluid 3He. We found that at ultra low in the limit of ultra low temperatures. 1. INTRODUCTION A closed cell with a small orifice, immersed

  19. An atom trap trace analysis (ATTA) system for measuring ultra-low contamination by krypton in

    E-Print Network [OSTI]

    Zelevinsky, Tanya

    An atom trap trace analysis (ATTA) system for measuring ultra-low contamination by krypton in xenon ultra-low contamination by krypton in xenon dark matter detectors Tae Hyun Yoon The XENON dark matter analysis (ATTA) device to detect the ultra-low kryp- ton concentration in the xenon target. This project

  20. Analysis, Design, and Testing of Airfoils for Use at Ultra-Low Reynolds Numbers

    E-Print Network [OSTI]

    Stanford University

    Analysis, Design, and Testing of Airfoils for Use at Ultra- Low Reynolds Numbers Peter J. Kunz Ilan M. Kroo Abstract: Advances in technology have begun to make ultra-low Reynolds number flight a real of the relevant aerodynamics. A reasonable starting point is the study of airfoil section aerodynamics at ultra-low

  1. Emissions From Various Biodiesel Sources Compared to a Range of Diesel Fuels in DPF Equipped Diesel Engines

    SciTech Connect (OSTI)

    Williams, A.; Burton, J.; Christensen, E.; McCormick, R. L.; Tester, J.

    2011-01-01T23:59:59.000Z

    The purpose of this study was to measure the impact of various sources of petroleum-based and bio-based diesel fuels on regulated emissions and fuel economy in diesel particulate filter (DPF) equipped diesel engines. Two model year 2008 diesel engines were tested with nine fuels including a certification ultra-low sulfur diesel (ULSD), local ULSD, high aromatic ULSD, low aromatic ULSD, and twenty percent blends of biodiesel derived from algae, camelina, soy, tallow, and yellow grease. Regulated emissions were measured over the heavy duty diesel transient test cycle. Measurements were also made of DPF-out particle size distribution and total particle count from a 13-mode steady state test using a fast mobility particle sizer. Test engines were a 2008 Cummins ISB and a 2008 International Maxx Force 10, both equipped with actively regenerated DPFs. Fuel consumption was roughly 2% greater over the transient test cycle for the B20 blends versus certification ULSD in both engines, consistent with the slightly lower energy content of biodiesel. Unlike studies conducted on older model engines, these engines equipped with diesel oxidation catalysts and DPFs showed small or no measurable fuel effect on the tailpipe emissions of total hydrocarbons (THC), carbon monoxide (CO) and particulate matter (PM). No differences in particle size distribution or total particle count were seen in a comparison of certification ULSD and B20 soy, with the exception of engine idling conditions where B20 produced a small reduction in the number of nucleation mode particles. In the Cummins engine, B20 prepared from algae, camelina, soy, and tallow resulted in an approximately 2.5% increase in nitrogen oxides (NO{sub x}) compared to the base fuel. The International engine demonstrated a higher degree of variability for NO{sub x} emissions, and fuel effects could not be resolved (p > 0.05). The group of petroleum diesel test fuels produced a range of NO{sub x} emissions very similar to that caused by blending of biodiesel. Test cycles where an active regeneration of the DPF occurred resulted in a nearly threefold increase in NO{sub x} emissions and a 15% increase in fuel consumption. The full quantification of DPF regeneration events further complicates the accurate calculation of fuel impacts on emissions and fuel consumption.

  2. Ultra-low-loss tapered optical fibers with minimal lengths

    E-Print Network [OSTI]

    Ryutaro Nagai; Takao Aoki

    2014-11-09T23:59:59.000Z

    We design and fabricate ultra-low-loss tapered optical fibers (TOFs) with minimal lengths. We first optimize variations of the torch scan length using the flame-brush method for fabricating TOFs with taper angles that satisfy the adiabaticity criteria. We accordingly fabricate TOFs with optimal shapes and compare their transmission to TOFs with a constant taper angle and TOFs with an exponential shape. The highest transmission measured for TOFs with an optimal shape is in excess of 99.7 % with a total TOF length of only 23 mm, whereas TOFs with a constant taper angle of 2 mrad reach 99.6 % transmission for a 63 mm TOF length.

  3. Cryostat for Ultra-low-energy Threshold Germanium Spectrometers

    SciTech Connect (OSTI)

    Aalseth, Craig E.; Bonicalzi, Ricco; Fast, James E.; Hossbach, Todd W.; Orrell, John L.; Overman, Cory T.; VanDevender, Brent A.

    2013-04-01T23:59:59.000Z

    Abstract: This paper presents progress on the development of a cryostat intended to improve upon the low-energy threshold (below 0.5 keV) of p-type point contact germanium gamma-ray spectrometers. Ultra-low energy thresholds are important in the detection of low-energy nuclear recoils, an event class relevant to both dark matter direct detection and measurement of coherent neutrino-nucleus scattering. The cryostat design, including a thermal and electrical-field model, is presented. A prototype cryostat has been assembled and data acquired to evaluate its vacuum and thermal performance.

  4. Cryostat for Ultra-low-energy Threshold Germanium Spectrometers

    E-Print Network [OSTI]

    Craig E. Aalseth; Ricco M. Bonicalzi; James E. Fast; Todd W. Hossbach; John L. Orrell; Cory T. Overman; Brent A. Vandevender

    2012-10-08T23:59:59.000Z

    This paper presents progress on the development of a cryostat intended to improve upon the low-energy threshold (below 0.5 keV) of p-type point contact germanium gamma-ray spectrometers. Ultra-low energy thresholds are important in the detection of low-energy nuclear recoils, an event class relevant to both dark matter direct detection and measurement of coherent neutrino-nucleus scattering. The cryostat design, including a thermal and electrical-field model, is given. A prototype cryostat has been assembled and data acquired to evaluate its vacuum and thermal performance.

  5. High Efficiency, Ultra-Low Emission, Integrated Process Heater System

    SciTech Connect (OSTI)

    Mason, Howard; Boral, Anindya; Chhotray, San; Martin, Matthew

    2006-06-19T23:59:59.000Z

    The team of TIAX LLC, ExxonMobil Research and Engineering Company, and Callidus Technologies, LLC conducted a six-year program to develop an ultra-low emission process heater burner and an advanced high efficiency heater design. This project addresses the critical need of process heater operators for reliable, economical emission reduction technologies to comply with stringent emission regulations, and for heater design alternatives that reduce process heater energy requirements without significant cost increase. The key project targets were NOx emissions of 10 ppm (@ 3% O2), and a heater thermal efficiency of 95 percent. The ultra low NOx burner was developed through a series of pilot-scale and field tests combined with computational fluid dynamic modeling to arrive at simultaneous low emissions and suitable flame shape and stability. Pilot scale tests were run at TIAX, at the 2 MMBtu/hr scale, and at Callidus at 8 MMBtu/hr. The full scale burner was installed on a 14 burner atmospheric pipestill furnace at an ExxonMobil refinery. A variety of burner configurations, gas tips and flame stabilizers were tested to determine the lowest emissions with acceptable flame shape and stability. The resulting NOx emissions were 22 ppm on average. Starting in 2001, Callidus commercialized the original ultra low NOx burner and made subsequent design improvements in a series of commercial burners evolving from the original concept and/or development. Emissions in the field with the ultra low-NOx burner over a broad spectrum of heater applications have varied from 5 ppm to 30 ppm depending on heater geometry, heater service, fuel and firing capacity. To date, 1550 of the original burners, and 2500 of subsequent generation burners have been sold by Callidus. The advanced heater design was developed by parametric evaluations of a variety of furnace and combustion air preheater configurations and technologies for enhancing convective and radiative heat transfer. The design evolution relied heavily on computational fluid dynamic predictions of design alternatives. The final design features modular separate radiant cells, each with one and two-side fired vertical tubes. The convection section configuration is vertical tube banks enclosed in the radiant channels. Commercial modular plate air preheaters are used. The predicted performance for the integrated advanced heater and Callidus burner is 95 percent efficiency with 9 ppm NOx emissions firing natural gas, and 12 ppm firing refinery gas. The total erected cost is less than a conventional heater with combustion air preheat.

  6. GRABGAM Analysis of Ultra-Low-Level HPGe Gamma Spectra

    SciTech Connect (OSTI)

    Winn, W.G.

    1999-07-28T23:59:59.000Z

    The GRABGAM code has been used successfully for ultra-low level HPGe gamma spectrometry analysis since its development in 1985 at Savannah River Technology Center (SRTC). Although numerous gamma analysis codes existed at that time, reviews of institutional and commercial codes indicated that none addressed all features that were desired by SRTC. Furthermore, it was recognized that development of an in-house code would better facilitate future evolution of the code to address SRTC needs based on experience with low-level spectra. GRABGAM derives its name from Gamma Ray Analysis BASIC Generated At MCA/PC.

  7. PPPL3161 Preprint Date: February 1996, UC420, 426, 427 Global Stability Study of the Ultra Low Aspect Ratio Tokamak,

    E-Print Network [OSTI]

    Low Aspect Ratio Tokamak, Global Stability Study of the Ultra Low Aspect Ratio Tokamak, Global Stability Study of the Ultra Low Aspect Ratio Tokamak, Global Stability Study of the Ultra Low Aspect Ratio Tokamak, Global Stability Study of the Ultra Low Aspect Ratio Tokamak, ULART ULART ULART ULART ULART M

  8. 2566 IEEE TRANSACTIONS ON NUCLEAR SCIENCE, VOL. 55, NO. 5, OCTOBER 2008 Virtual Colonoscopy Screening With Ultra Low-Dose

    E-Print Network [OSTI]

    Screening With Ultra Low-Dose CT and Less-Stressful Bowel Preparation: A Computer Simulation Study Jing Wang a simulation study to demonstrate a possible ultra low-dose CT technique for VC. The ultra low-dose abdominal by a filtered backprojection algorithm for the ultra low-dose CT im- ages. The patient-specific virtual colon

  9. PPPL-3161 -Preprint Date: February 1996, UC-420, 426, 427 Global Stability Study of the Ultra Low Aspect Ratio Tokamak,Global Stability Study of the Ultra Low Aspect Ratio Tokamak,Global Stability Study of the Ultra Low Aspect Ratio Tokamak,Global Stabili

    E-Print Network [OSTI]

    Low Aspect Ratio Tokamak,Global Stability Study of the Ultra Low Aspect Ratio Tokamak,Global Stability Study of the Ultra Low Aspect Ratio Tokamak,Global Stability Study of the Ultra Low Aspect Ratio Tokamak,Global Stability Study of the Ultra Low Aspect Ratio Tokamak, ULARTULARTULARTULARTULART M. Yamada1, A. Morita2, N

  10. Design Considerations for Large Mass Ultra-Low Background Experiments

    SciTech Connect (OSTI)

    Aguayo Navarrete, Estanislao; Reid, Douglas J.; Fast, James E.; Orrell, John L.

    2011-07-01T23:59:59.000Z

    Summary The objective of this document is to present the designers of the next generation of large-mass, ultra-low background experiments with lessons learned and design strategies from previous experimental work. Design issues divided by topic into mechanical, thermal and electrical requirements are addressed. Large mass low-background experiments have been recognized by the scientific community as appropriate tools to aid in the refinement of the standard model. The design of these experiments is very costly and a rigorous engineering review is required for their success. The extreme conditions that the components of the experiment must withstand (heavy shielding, vacuum/pressure and temperature gradients), in combination with unprecedented noise levels, necessitate engineering guidance to support quality construction and safe operating conditions. Physical properties and analytical results of typical construction materials are presented. Design considerations for achieving ultra-low-noise data acquisition systems are addressed. Five large-mass, low-background conceptual designs for the one-tonne scale germanium experiment are proposed and analyzed. The result is a series of recommendations for future experiments engineering and for the Majorana simulation task group to evaluate the different design approaches.

  11. BID MUST BE RECEIVED NO LATER THAN Please indicate: Minority Business

    E-Print Network [OSTI]

    Gering, Jon C.

    for unleaded gasoline and Number 2 Ultra Low Sulfur Diesel fuel (#2 Red Diesel) for use on their Grounds or decrease quantities. ESTIMATES: Grounds Unleaded Gasoline ­ 2,000 gallons Diesel, ultra low sulphur #2 Red gallons Diesel, ultra low sulphur #2 Red ­ 700 gallons Award will be made on an "all or none" or "item

  12. High-Efficiency, Ultra-Low Emission Combustion in a Heavy-Duty...

    Broader source: Energy.gov (indexed) [DOE]

    Efficiency, Ultra-Low Emission Combustion in a Heavy-Duty Engine via Fuel Reactivity Control Rolf D. Reitz, Reed Hanson, Derek Splitter, Sage Kokjohn Engine Research Center...

  13. Ultra-low density microcellular polymer foam and method

    DOE Patents [OSTI]

    Simandl, R.F.; Brown, J.D.

    1996-03-19T23:59:59.000Z

    An ultra-low density, microcellular open-celled polymer foam and a method for making such foam are disclosed. A polymer is dissolved in a heated solution consisting essentially of at least one solvent for the dissolution of the polymer in the heated solution and the phase inversion of the dissolved polymer to a liquid gel upon sufficient cooling of the heated solution. The heated solution is contained in a containment means provided with a nucleating promoting means having a relatively rough surface formed of fixed nucleating sites. The heated solution is cooled for a period of time sufficient to form a liquid gel of the polymer by phase inversion. From the gel, a porous foam having a density of less than about 12.0 mg/cm{sup 3} and open porosity provided by well interconnected strut morphology is formed.

  14. Ultra-Low Amplitude Cepheids in the Large Magellanic Cloud

    E-Print Network [OSTI]

    J. Robert Buchler; Peter R. Wood; Stefan Keller; Igor Soszynski

    2005-08-26T23:59:59.000Z

    The MACHO variables of LMC Field 77 that lie in the vicinity of the Cepheid instability strip are reexamined. Among the 144 variables that we identify as Cepheids we find 14 that have Fourier amplitudes ultra-low amplitude (ULA) Cepheids. The variability of these objects is verified by a comparison of the MACHO red with the MACHO blue lightcurves and with those of the corresponding OGLE LMC stars. The occurrence of ULA Cepheids is in agreement with theory. We have also discovered 2 low amplitude variables whose periods are about a factor of 5--6 smaller than those of F Cepheids of equal apparent magnitude. We suggest that these objects are Cepheids undergoing pulsations in a surface mode and that they belong to a novel class of Strange Cepheids (or Surface Mode Cepheids) whose existence was predicted by Buchler et al. (1997).

  15. Ultra-low density microcellular polymer foam and method

    DOE Patents [OSTI]

    Simandl, Ronald F. (Farragut, TN); Brown, John D. (Harriman, TN)

    1996-01-01T23:59:59.000Z

    An ultra-low density, microcellular open-celled polymer foam and a method for making such foam. A polymer is dissolved in a heated solution consisting essentially of at least one solvent for the dissolution of the polymer in the heated solution and the phase inversion of the dissolved polymer to a liquid gel upon sufficient cooling of the heated solution. The heated solution is contained in a containment means provided with a nucleating promoting means having a relatively rough surface formed of fixed nucleating sites. The heated solution is cooled for a period of time sufficient to form a liquid gel of the polymer by phase inversion. From the gel, a porous foam having a density of less than about 12.0 mg/cm.sup.3 and open porosity provided by well interconnected strut morphology is formed.

  16. Effect of E85 on RCCI Performance and Emissions on a Multi-Cylinder Light-Duty Diesel Engine - SAE World Congress

    SciTech Connect (OSTI)

    Curran, Scott [ORNL; Hanson, Reed M [ORNL; Wagner, Robert M [ORNL

    2012-01-01T23:59:59.000Z

    This paper investigates the effect of E85 on load expansion and FTP modal point emissions indices under reactivity controlled compression ignition (RCCI) operation on a light-duty multi-cylinder diesel engine. A General Motors (GM) 1.9L four-cylinder diesel engine with the stock compression ratio of 17.5:1, common rail diesel injection system, high-pressure exhaust gas recirculation (EGR) system and variable geometry turbocharger was modified to allow for port fuel injection with gasoline or E85. Controlling the fuel reactivity in-cylinder by the adjustment of the ratio of premixed low-reactivity fuel (gasoline or E85) to direct injected high reactivity fuel (diesel fuel) has been shown to extend the operating range of high-efficiency clean combustion (HECC) compared to the use of a single fuel alone as in homogeneous charge compression ignition (HCCI) or premixed charge compression ignition (PCCI). The effect of E85 on the Ad-hoc federal test procedure (FTP) modal points is explored along with the effect of load expansion through the light-duty diesel speed operating range. The Ad-hoc FTP modal points of 1500 rpm, 1.0bar brake mean effective pressure (BMEP); 1500rpm, 2.6bar BMEP; 2000rpm, 2.0bar BMEP; 2300rpm, 4.2bar BMEP; and 2600rpm, 8.8bar BMEP were explored. Previous results with 96 RON unleaded test gasoline (UTG-96) and ultra-low sulfur diesel (ULSD) showed that with stock hardware, the 2600rpm, 8.8bar BMEP modal point was not obtainable due to excessive cylinder pressure rise rate and unstable combustion both with and without the use of EGR. Brake thermal efficiency and emissions performance of RCCI operation with E85 and ULSD is explored and compared against conventional diesel combustion (CDC) and RCCI operation with UTG 96 and ULSD.

  17. Molecular Caulk: A Pore Sealing Technology for Ultra-low k Dielectrics Jay J. Senkevich1

    E-Print Network [OSTI]

    Wang, Gwo-Ching

    Molecular Caulk: A Pore Sealing Technology for Ultra-low k Dielectrics Jay J. Senkevich1 Washington Ave., Albany, NY 12222 Abstract Much effort has been undertaken to develop high performance ultra-low k ( 2.2) (ULK) dielectrics to improve the interconnect speed of ultra-large scale integrated devices

  18. 9 Ultra Low Temperature ADI 2 9.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

    E-Print Network [OSTI]

    Cambridge, University of

    Contents 9 Ultra Low Temperature ADI 2 9.1 Introduction;Chapter 9 Ultra Low Temperature ADI 9.1 Introduction It has been indicated that a family of austempered]. These steels contain high carbon silicon and manganese, and they are isothermally heat treated at very low

  19. Low Carbon Footprint and Ultra Low NOx Boilers through Efficiency Gain 

    E-Print Network [OSTI]

    Benz, R,; Staedter, M.

    2008-01-01T23:59:59.000Z

    Low Carbon Footprint and Ultra Low NOx Boilers through Efficiency Gain Robert Benz Marcel Staedter... Industrial Energy Technology Conference, New Orleans, LA, May 6-9, 2008. M. Staedter, R. Benz / Low Carbon, Ultra Low NOx through Efficiency Gain where y denotes the mole fraction of excess...

  20. Technical Reports Ultra-low Dose Lung CT Perfusion Regularized by

    E-Print Network [OSTI]

    Virginia Tech

    Technical Reports Ultra-low Dose Lung CT Perfusion Regularized by a Previous Scan1 Hengyong Yu, Ph­regularized reconstruction (PSRR) method was proposed to reduce radiation dose and applied to lung perfusion studies. Normal and ultra-low-dose lung computed tomographic perfusion studies were compared in terms of the estimation

  1. Ultra-low rare earth element content in accreted ice from sub-glacial Lake Vostok, Antarctica

    E-Print Network [OSTI]

    Howat, Ian M.

    Ultra-low rare earth element content in accreted ice from sub-glacial Lake Vostok, Antarctica Paolo. We suggest that such ultra-low concentrations are unlikely to be representative of the real REE

  2. Active and Passive Elec. Comp., September 2003, Vol. 26, pp. 151166 ULTRA-LOW TEMPERATURE COEFFICIENT OF

    E-Print Network [OSTI]

    Azad, Abdul-Majeed

    Active and Passive Elec. Comp., September 2003, Vol. 26, pp. 151­166 ULTRA-LOW TEMPERATURE that this material system possessed low dielectric constant and ultra-low temperature coefficient of capacitance (TCC

  3. Adaptive Injection Strategies (AIS) for Ultra-low Emissions Diesel Engines

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The Future of1 AAccelerated aging of1.1Energy DPF forWorkshopDepartment|

  4. Accelerating From vehicles on the road to the energy that powers

    E-Print Network [OSTI]

    Pennycook, Steve

    ultra-low sulfur diesel fuel rule ORNL and the National Renewable Energy Laboratory co-2 emis- sions levels with ultra-low sulfur diesel fuel. Power electronics and electric propulsion-led a comprehensive research and test program to determine the effects of diesel fuel sulfur on emissions and emission

  5. Life-Cycle Energy Demand of Computational Logic: From High-Performance 32nm CPU to Ultra-Low-Power 130nm MCU

    E-Print Network [OSTI]

    Bol, David; Boyd, Sarah; Dornfeld, David

    2011-01-01T23:59:59.000Z

    Performance 32 nm CPU to Ultra-Low-Power 130 nm MCU Davidboxes and smart phones to ultra-low-power 130 nm MCUs forthe energy demand for ultra-low-power MCUs is completely

  6. Analgesia, enhancement of spinal morphine antinociception, and inhibition of tolerance by ultra-low dose of the ?2A-adrenoceptor selective antagonist BRL44408

    E-Print Network [OSTI]

    2014-01-01T23:59:59.000Z

    Shen, K.F. , 1995. Ultra-low concentrations of naloxoneCahill, C.M. , 2010. Ultra-low dose naltrexone attenuatesand hyperalgesia by an ultra-low dose of the alpha-2-

  7. Life-Cycle Energy Demand of Computational Logic: From High-Performance 32nm CPU to Ultra-Low-Power 130nm MCU

    E-Print Network [OSTI]

    Bol, David; Boyd, Sarah; Dornfeld, David

    2011-01-01T23:59:59.000Z

    Performance 32 nm CPU to Ultra-Low-Power 130 nm MCU Davidboxes and smart phones to ultra-low-power 130 nm MCUs forthe energy demand for ultra-low-power MCUs is completely

  8. DOE Will Convert Northeast Home Heating Oil Reserve to Ultra Low Sulfur

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: Theof"WaveInteractionsMaterials | Department

  9. A Novel Si-Tunnel FET based SRAM Design for Ultra Low-Power 0.3V VDD Applications

    E-Print Network [OSTI]

    Yener, Aylin

    A Novel Si-Tunnel FET based SRAM Design for Ultra Low-Power 0.3V VDD Applications J. Singh, K-Band Tunnel Field Effect Transistors (TFETs) in SRAMs at ultra low supply voltages. The uni design using Si- TFETs for reliable operation with low leakage at ultra low voltages. We also demonstrate

  10. Characterization of oxygen and nitrogen rapid thermal annealing processes for ultra-low-k SiCOH films

    E-Print Network [OSTI]

    Boo, Jin-Hyo

    Characterization of oxygen and nitrogen rapid thermal annealing processes for ultra-low-k Si is suggested and characterized in this work for improvement of SiCOH ultra-low-k (k 2.4) film properties. Low is decreased, and the ultra-low-k films (k

  11. Chair for Computer Networks and Internet -Universitt Tbingen 1 ffor an open source, ultra low delay audio coding

    E-Print Network [OSTI]

    Carle, Georg

    an open source, ultra low delay audio coding Extending the packet loss concealment algorithm ITU G 711 A di 1 t f ll b d idthITU G.711 Appendix 1 to full bandwidth Comparing ultra low delay audio codecs SSummary Chair for Computer Networks and Internet - Universität Tübingen 2 #12;From speech to ultra-low

  12. MAC Design for Supporting Ultra Low Duty Cycle in Wireless Sensor Networks1 *Wooguil PakO

    E-Print Network [OSTI]

    Bahk, Saewoong

    MAC Design for Supporting Ultra Low Duty Cycle in Wireless Sensor Networks1 *Wooguil PakO , *Hyuk.1%). Our proposed U-MAC (Ultra low duty cycle MAC) protocol targets achieving low energy consumption under. In this paper, we propose a new MAC algorithm called U-MAC (Ultra low duty cycle MAC) that works effectively

  13. Trading off Reliability and Power-Consumption in Ultra-Low Power Systems Atul Maheshwari, Wayne Burleson and Russell Tessier

    E-Print Network [OSTI]

    Tessier, Russell

    Trading off Reliability and Power-Consumption in Ultra-Low Power Systems Atul Maheshwari, Wayne but also for ultra-low power consumption due to limited battery life. This paper explores architecture (Binary and Gray) we show that temporal re- dundancy is best suited for these ultra-low power and low

  14. Modeling the ratios of SKKS and SKS amplitudes with ultra-low velocity zones at the core-mantle boundary

    E-Print Network [OSTI]

    Ritsema, Jeroen

    Modeling the ratios of SKKS and SKS amplitudes with ultra-low velocity zones at the core of earthquakes in Indonesia. Modeling of SKKS/SKS indicate that Ultra-Low Velocity Zones (ULVZs), layers, and M. S. Thorne (2009), Modeling the ratios of SKKS and SKS amplitudes with ultra-low velocity zones

  15. Centralized route recovery based on multi-hop wakeup time estimation for wireless sensor networks with ultra low duty cycles

    E-Print Network [OSTI]

    Bahk, Saewoong

    with ultra low duty cycles Wooguil Pak, Saewoong Bahk Department of EECS & INMC, Seoul National University Keywords: Wireless sensor network Routing protocol Ultra low duty cycle Network lifetime Multi-hop wakeup time estimation to maximize the network lifetime of WSNs under ultra low duty cycles. It does not use

  16. Seismic structure and ultra-low velocity zones at the base of the Earth's mantle beneath Southeast Asia

    E-Print Network [OSTI]

    Wen, Lianxing

    Seismic structure and ultra-low velocity zones at the base of the Earth's mantle beneath Southeast t We constrain seismic structure and ultra-low velocity zones near the Earth's core-mantle boundary that the strong scatterers represent ultra-low velocity zones (ULVZs). We suggest that the seismic structure

  17. Ultra low resistance, non-alloyed ohmic contacts to n-InGaAs Ashish K. Baraskar1

    E-Print Network [OSTI]

    Rodwell, Mark J. W.

    Ultra low resistance, non-alloyed ohmic contacts to n-InGaAs Ashish K. Baraskar1 , Mark A. Wistey1 and fmax [1], [2]. Here we report the ultra-low specific contact resistivity (c) of non-alloyed in duration. These data indicate that the in-situ Mo gives ultra low Ohmic contacts, probably due

  18. Exhaust Gas Recirculation Cooler Fouling in Diesel Applications: Fundamental Studies Deposit Properties and Microstructure

    SciTech Connect (OSTI)

    Storey, John Morse [ORNL; Sluder, Scott [ORNL; Lance, Michael J [ORNL; Styles, Dan [Ford Motor Company; Simko, Steve [Ford Motor Company

    2013-01-01T23:59:59.000Z

    This paper reports on the results of experimental efforts aimed at improving the understanding of the mechanisms and conditions at play in the fouling of EGR coolers. An experimental apparatus was constructed to utilize simplified surrogate heat exchanger tubes in lieu of full-size heat exchangers. The use of these surrogate tubes allowed removal of the tubes after exposure to engine exhaust for study of the deposit layer and its properties. The exhaust used for fouling the surrogate tubes was produced using a modern medium-duty diesel engine fueled with both ultra-low sulfur diesel and biodiesel blends. At long exposure times, no significant difference in the fouling rate was observed between fuel types and HC levels. Surface coatings for the tubes were also evaluated to determine their impact on deposit growth. No surface treatment or coating produced a reduction in the fouling rate or any evidence of deposit removal. In addition, microstructural analysis of the fouling layers was performed using optical and electron microscopy in order to better understand the deposition mechanism. The experimental results are consistent with thermophoretic deposition for deposit formation, and van der Waals attraction between the deposit surface and exhaust-borne particulate.

  19. Ultra-low field nuclear magnetic resonance and magnetic resonance imaging to discriminate and identify materials

    DOE Patents [OSTI]

    Kraus, Robert H. (Los Alamos, NM); Matlashov, Andrei N. (Los Alamos, NM); Espy, Michelle A. (Los Alamos, NM); Volegov, Petr L. (Los Alamos, NM)

    2010-03-30T23:59:59.000Z

    An ultra-low magnetic field NMR system can non-invasively examine containers. Database matching techniques can then identify hazardous materials within the containers. Ultra-low field NMR systems are ideal for this purpose because they do not require large powerful magnets and because they can examine materials enclosed in conductive shells such as lead shells. The NMR examination technique can be combined with ultra-low field NMR imaging, where an NMR image is obtained and analyzed to identify target volumes. Spatial sensitivity encoding can also be used to identify target volumes. After the target volumes are identified the NMR measurement technique can be used to identify their contents.

  20. Methodology for Formulating Diesel Surrogate Fuels with Accurate Compositional, Ignition-Quality, and Volatility Characteristics

    SciTech Connect (OSTI)

    Mueller, C. J.; Cannella, W. J.; Bruno, T. J.; Bunting, B.; Dettman, H. D.; Franz, J. A.; Huber, M. L.; Natarajan, M.; Pitz, W. J.; Ratcliff, M. A.; Wright, K.

    2012-06-21T23:59:59.000Z

    In this study, a novel approach was developed to formulate surrogate fuels having characteristics that are representative of diesel fuels produced from real-world refinery streams. Because diesel fuels typically consist of hundreds of compounds, it is difficult to conclusively determine the effects of fuel composition on combustion properties. Surrogate fuels, being simpler representations of these practical fuels, are of interest because they can provide a better understanding of fundamental fuel-composition and property effects on combustion and emissions-formation processes in internal-combustion engines. In addition, the application of surrogate fuels in numerical simulations with accurate vaporization, mixing, and combustion models could revolutionize future engine designs by enabling computational optimization for evolving real fuels. Dependable computational design would not only improve engine function, it would do so at significant cost savings relative to current optimization strategies that rely on physical testing of hardware prototypes. The approach in this study utilized the state-of-the-art techniques of {sup 13}C and {sup 1}H nuclear magnetic resonance spectroscopy and the advanced distillation curve to characterize fuel composition and volatility, respectively. The ignition quality was quantified by the derived cetane number. Two well-characterized, ultra-low-sulfur No.2 diesel reference fuels produced from refinery streams were used as target fuels: a 2007 emissions certification fuel and a Coordinating Research Council (CRC) Fuels for Advanced Combustion Engines (FACE) diesel fuel. A surrogate was created for each target fuel by blending eight pure compounds. The known carbon bond types within the pure compounds, as well as models for the ignition qualities and volatilities of their mixtures, were used in a multiproperty regression algorithm to determine optimal surrogate formulations. The predicted and measured surrogate-fuel properties were quantitatively compared to the measured target-fuel properties, and good agreement was found.

  1. Soybean and Coconut Biodiesel Fuel Effects on Combustion Characteristics in a Light-Duty Diesel Engine

    SciTech Connect (OSTI)

    Han, Manbae [ORNL; Cho, Kukwon [ORNL; Sluder, Scott [ORNL; Wagner, Robert M [ORNL

    2008-01-01T23:59:59.000Z

    This study investigated the effects of soybean- and coconut-derived biodiesel fuels on combustion characteristics in a 1.7-liter direct injection, common rail diesel engine. Five sets of fuels were studied: 2007 ultra-low sulfur diesel (ULSD), 5% and 20% volumetric blends of soybean biodiesel with ULSD (soybean B5 and B20), and 5% and 20% volumetric blends of coconut biodiesel with ULSD (coconut B5 and B20). In conventional diesel combustion mode, particulate matter (PM) and nitrogen oxides (NO/dx) emissions were similar for all fuels studied except soybean B20. Soybean B20 produced the lowest PM but the highest NO/dx emissions. Compared with conventional diesel combustion mode, high efficiency clean combustion (HECC) mode, achieved by increased EGR and combustion phasing, significantly reduced both PM and NO/dx emissions for all fuels studied at the expense of higher hydrocarbon (HC) and carbon monoxide (CO) emissions and an increase in fuel consumption (less than 4%). ULSD, soybean B5, and coconut B5 showed no difference in exhaust emissions. However, PM emissions increased slightly for soybean B20 and coconut B20. NO/dx emissions increased significantly for soybean B20, while those for coconut B20 were comparable to ULSD. Differences in the chemical and physical properties of soybean and coconut biodiesel fuels compared with ULSD, such as higher fuel-borne oxygen, greater viscosity, and higher boiling temperatures, play a key role in combustion processes and, therefore, exhaust emissions. Furthermore, the highly unsaturated ester composition in soybean biodiesel can be another factor in the increase of NO/dx emissions.

  2. Well Performance Analysis for Low to Ultra-low Permeability Reservoir Systems 

    E-Print Network [OSTI]

    Ilk, Dilhan

    2010-10-12T23:59:59.000Z

    to evaluate well performance in unconventional (i.e., low to ultra-low permeability) reservoir systems. The specific tasks achieved in this work include the following: ? Integrated Diagnostics and Analysis of Production Data in Unconventional Reservoirs: We...

  3. PEM fuel cellstack development based on membrane-electrode assemblies of ultra-low platinum loadings

    SciTech Connect (OSTI)

    Zawodzinski, C.; Wilson, M.S.; Gottesfeld, S.

    1995-09-01T23:59:59.000Z

    Attempt is made to scale-up single cell technology, based on ultra-low platinum loadings, to develop a polymer electrolyte membrane fuel cell stack for stationary power generation.

  4. Vehicle Technologies Office Merit Review 2014: Thermally Stable Ultra-Low Temperature Oxidation Catalysts

    Broader source: Energy.gov [DOE]

    Presentation given by [company name] at 2014 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about thermally stable ultra-low...

  5. 8, 27152744, 2008 Nanoparticle

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    formation in the exhaust of vehicles running on ultra-low sulfur fuel Hua Du and Fangqun Yu Atmospheric regenerating diesel particle filters (CRDPFs) have to be employed5 on vehicles and fuel with ultra-low sulfur concentrations have also been detected for vehicles running on ultra-low sulfur fuel but without CRDPFs. The main

  6. Ultra Low NOx Catalytic Combustion for IGCC Power Plants

    SciTech Connect (OSTI)

    Shahrokh Etemad; Benjamin Baird; Sandeep Alavandi; William Pfefferle

    2008-03-31T23:59:59.000Z

    In order to meet DOE's goals of developing low-emissions coal-based power systems, PCI has further developed and adapted it's Rich-Catalytic Lean-burn (RCL{reg_sign}) catalytic reactor to a combustion system operating on syngas as a fuel. The technology offers ultra-low emissions without the cost of exhaust after-treatment, with high efficiency (avoidance of after-treatment losses and reduced diluent requirements), and with catalytically stabilized combustion which extends the lower Btu limit for syngas operation. Tests were performed in PCI's sub-scale high-pressure (10 atm) test rig, using a two-stage (catalytic then gas-phase) combustion process for syngas fuel. In this process, the first stage consists of a fuel-rich mixture reacting on a catalyst with final and excess combustion air used to cool the catalyst. The second stage is a gas-phase combustor, where the air used for cooling the catalyst mixes with the catalytic reactor effluent to provide for final gas-phase burnout and dilution to fuel-lean combustion products. During testing, operating with a simulated Tampa Electric's Polk Power Station syngas, the NOx emissions program goal of less than 0.03 lbs/MMBtu (6 ppm at 15% O{sub 2}) was met. NOx emissions were generally near 0.01 lbs/MMBtu (2 ppm at 15% O{sub 2}) (PCI's target) over a range on engine firing temperatures. In addition, low emissions were shown for alternative fuels including high hydrogen content refinery fuel gas and low BTU content Blast Furnace Gas (BFG). For the refinery fuel gas increased resistance to combustor flashback was achieved through preferential consumption of hydrogen in the catalytic bed. In the case of BFG, stable combustion for fuels as low as 88 BTU/ft{sup 3} was established and maintained without the need for using co-firing. This was achieved based on the upstream catalytic reaction delivering a hotter (and thus more reactive) product to the flame zone. The PCI catalytic reactor was also shown to be active in ammonia reduction in fuel allowing potential reductions in the burner NOx production. These reductions of NOx emissions and expanded alternative fuel capability make the rich catalytic combustor uniquely situated to provide reductions in capital costs through elimination of requirements for SCR, operating costs through reduction in need for NOx abating dilution, SCR operating costs, and need for co-firing fuels allowing use of lower value but more available fuels, and efficiency of an engine through reduction in dilution flows.

  7. Aftertreatment Technologies for Off-Highway Heavy-Duty Diesel Engines

    SciTech Connect (OSTI)

    Kass, M.D.

    2008-07-15T23:59:59.000Z

    The objective of this program was to explore a combination of advanced injection control and urea-selective catalytic reduction (SCR) to reduce the emissions of oxides of nitrogen (NOx) and particulate matter (PM) from a Tier 2 off-highway diesel engine to Tier 3 emission targets while maintaining fuel efficiency. The engine used in this investigation was a 2004 4.5L John Deere PowerTechTM; this engine was not equipped with exhaust gas recirculation (EGR). Under the original CRADA, the principal objective was to assess whether Tier 3 PM emission targets could be met solely by increasing the rail pressure. Although high rail pressure will lower the total PM emissions, it has a contrary effect to raise NOx emissions. To address this effect, a urea-SCR system was used to determine whether the enhanced NOx levels, associated with high rail pressure, could be reduced to Tier 3 levels. A key attraction for this approach is that it eliminates the need for a Diesel particulate filter (DPF) to remove PM emissions. The original CRADA effort was also performed using No.2 Diesel fuel having a maximum sulfur level of 500 ppm. After a few years, the CRADA scope was expanded to include exploration of advanced injection strategies to improve catalyst regeneration and to explore the influence of urea-SCR on PM formation. During this period the emission targets also shifted to meeting more stringent Tier 4 emissions for NOx and PM, and the fuel type was changed to ultra-low sulfur Diesel (ULSD) having a maximum sulfur concentration of 15 ppm. New discoveries were made regarding PM formation at high rail pressures and the influences of oxidation catalysts and urea-SCR catalysts. These results are expected to provide a pathway for lower PM and NOx emissions for both off- and on-highway applications. Industrial in-kind support was available throughout the project period. Review of the research results were carried out on a regular basis (annual reports and meetings) followed by suggestions for improvement in ongoing work and direction for future work. A significant portion of the industrial support was in the form of experimentation, data analysis, data exchange, and technical consultation.

  8. CRYOGENIC 1.5-4.5 GHz ULTRA LOW NOISE AMPLIFIER Niklas Wadefalk*, Anders Mellberg, Iltcho Angelov, Emmanuil Choumas**, Erik Kollberg,

    E-Print Network [OSTI]

    CRYOGENIC 1.5-4.5 GHz ULTRA LOW NOISE AMPLIFIER Niklas Wadefalk*, Anders Mellberg, Iltcho Angelov amplifiers with ultra-low noise and very low DC power dissipation. Amplifiers with ultra- low noise and low.5-4.5 GHz ULTRA LOW NOISE AMPLIFIER Niklas Wadefalk, Anders Mellberg, Iltcho Angelov, Emmanuil Choumas, Erik

  9. IEEE TRANSACTIONS ON MICROWAVE THEORY AND TECHNIQUES, VOL. 51, NO. 6, JUNE 2003 1705 Cryogenic Wide-Band Ultra-Low-Noise IF

    E-Print Network [OSTI]

    -Band Ultra-Low-Noise IF Amplifiers Operating at Ultra-Low DC Power Niklas Wadefalk, Anders Mellberg, Iltcho Identifier 10.1109/TMTT.2003.812570 ultra-low-noise and ultra-low dc power dissipation are of interest--This paper describes cryogenic broad-band ampli- fiers with very low power consumption and very low noise

  10. IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS--II: EXPRESS BRIEFS, VOL. 59, NO. 4, APRIL 2012 193 Universal Principles for Ultra Low Power

    E-Print Network [OSTI]

    Sarpeshkar, Rahul

    Universal Principles for Ultra Low Power and Energy Efficient Design Rahul Sarpeshkar, Senior Member, IEEE

  11. DEEP DESULFURIZATION OF DIESEL FUELS BY A NOVEL INTEGRATED APPROACH

    SciTech Connect (OSTI)

    Xiaoliang Ma; Michael Sprague; Lu Sun; Chunshan Song

    2002-10-01T23:59:59.000Z

    In order to reduce the sulfur level in liquid hydrocarbon fuels for environmental protection and fuel cell applications, deep desulfurization of a model diesel fuel and a real diesel fuel was conducted by our SARS (selective adsorption for removing sulfur) process using the adsorbent A-2. Effect of temperature on the desulfurization process was examined. Adsorption desulfurization at ambient temperature, 24 h{sup -1} of LHSV over A-2 is efficient to remove dibenzothiophene (DBT) in the model diesel fuel, but difficult to remove 4-methyldibenzothiophene (4-MDBT) and 4,6-dimethyl-dibenzothiophene (4,6-DMDBT). Adsorption desulfurization at 150 C over A-2 can efficiently remove DBT, 4-MDBT and 4,6-DMDBT in the model diesel fuel. The sulfur content in the model diesel fuel can be reduced to less than 1 ppmw at 150 C without using hydrogen gas. The adsorption capacity corresponding to the break-through point is 6.9 milligram of sulfur per gram of A-2 (mg-S/g-A-2), and the saturate capacity is 13.7 mg-S/g-A-2. Adsorption desulfurization of a commercial diesel fuel with a total sulfur level of 47 ppmw was also performed at ambient temperature and 24 h{sup -1} of LHSV over the adsorbent A-2. The results show that only part of the sulfur compounds existing in the low sulfur diesel can be removed by adsorption over A-2 at such operating conditions, because (1) the all sulfur compounds in the low sulfur diesel are the refractory sulfur compounds that have one or two alkyl groups at the 4- and/or 6-positions of DBT, which inhibit the approach of the sulfur atom to the adsorption site; (2) some compounds coexisting in the commercial low sulfur diesel probably inhibit the interaction between the sulfur compounds and the adsorbent. Further work in determining the optimum operating conditions and screening better adsorbent is desired.

  12. untitled

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    District (Cents per Gallon Excluding Taxes) - Continued Geographic Area Month Ultra Low-Sulfur Diesel Fuel Low-Sulfur Diesel Fuel Sales to End Users Sales for Resale Sales to End...

  13. Appendix D: FEDERAL EMERGENCY AUTHORITIES AND POLICY DIRECTIVES

    Office of Environmental Management (EM)

    Institute, 2013. Agency Waiver Used for Allows EPA 40 C.F.R. 80.510 and 80.520 Ultra-Low Sulfur Diesel Allows the use of higher sulfur diesel in older cars, generators,...

  14. Experimental Studies for CPF and SCR Model, Control System, and OBD Development for Engines Using Diesel and Biodiesel Fuels

    SciTech Connect (OSTI)

    Johnson, John; Naber, Jeffrey; Parker, Gordon; Yang, Song-Lin; Stevens, Andrews; Pihl, Josh

    2013-04-30T23:59:59.000Z

    The research carried out on this project developed experimentally validated Diesel Oxidation Catalyst (DOC), Diesel Particulate Filter (DPF), and Selective Catalytic Reduction (SCR) high?fidelity models that served as the basis for the reduced order models used for internal state estimation. The high?fidelity and reduced order/estimator codes were evaluated by the industrial partners with feedback to MTU that improved the codes. Ammonia, particulate matter (PM) mass retained, PM concentration, and NOX sensors were evaluated and used in conjunction with the estimator codes. The data collected from PM experiments were used to develop the PM kinetics using the high?fidelity DPF code for both NO2 assisted oxidation and thermal oxidation for Ultra Low Sulfur Fuel (ULSF), and B10 and B20 biodiesel fuels. Nine SAE papers were presented and this technology transfer process should provide the basis for industry to improve the OBD and control of urea injection and fuel injection for active regeneration of the PM in the DPF using the computational techniques developed. This knowledge will provide industry the ability to reduce the emissions and fuel consumption from vehicles in the field. Four MS and three PhD Mechanical Engineering students were supported on this project and their thesis research provided them with expertise in experimental, modeling, and controls in aftertreatment systems.

  15. untitled

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    to avoid disclosure of individual company data. Note: In January 2007, ultra low-sulfur diesel fuel was added. Source: Energy Information Administration Form EIA-782A,...

  16. President Requests $842.1 Million for Fossil Energy Programs...

    Energy Savers [EERE]

    commercial storage. In FY 2012, NEHHOR converted to a 1 million barrel configuration of Ultra Low Sulfur Diesel (ULSD) stored in the Northeast terminals, to meet new Northeast...

  17. Ultra-low power, Zeno effect based optical modulation in a degenerate V-system with a

    E-Print Network [OSTI]

    Shahriar, Selim

    Ultra-low power, Zeno effect based optical modulation in a degenerate V-system with a tapered nano@northwestern.edu Abstract: We demonstrate an ultra-low light level optical modulator using a tapered nano fiber embedded. For a control power of 40 nW and a signal power of 100 pW, we observe near 100% modulation. The ultra-low power

  18. Integrated production/use of ultra low-ash coal, premium liquids and clean char. Technical report, March 1, 1992--May 31, 1992

    SciTech Connect (OSTI)

    Kruse, C.W.; Carlson, S.L. [Illinois State Geological Survey, Champaign, IL (United States); Snoeyink, V.L.; Feizoulof, C.; Assanis, D.N.; Syrimis, M. [Illinois Univ., Urbana, IL (United States); Fatemi, S.M. [Amoco Research Center, Naperville, IL (United States)

    1992-10-01T23:59:59.000Z

    The first step in the envisioned integrated, multi-product approach for utilizing Illinois coal is the production of ultra low-ash coal. Subsequent steps would convert low-ash coal to high-value products through mild gasification, char activation, and oxidation reactions. Approximately eight pounds of low-ash coal has been obtained from the crude reactor slurry produced for us at the University of North Dakota Energy and Environmental Research Center (UNDEERC). After treatment to remove the remaining meta-cresol, this material will be subjected to mild gasification. Low-ash mild gasification char will be activated and a catalyst surface will be added by oxidation. A 20% coal: 80% diesel fuel slurry was tested in cylinder two of a two-cylinder, diesel engine after the necessary modifications in the engine`s fuel injection system were made. Four tests indicated that the coal successfully substitutes for diesel fuel in the slurry. The fuel burns in the cylinder, with slightly improved thermal and combustion efficiency. The tests were performed at 1800 rpm and 2200 rpm and 75% load. The change in the surface properties of Calgon F-400 commercial activated carbon caused by several treatments were examined by X-ray Photoelectron Spectroscopy (XPS).

  19. Nitrogen dioxide, sulfur dioxide, and ammonia detector for remote sensing of vehicle emissions

    E-Print Network [OSTI]

    Denver, University of

    with sulfuric and nitric acids formed from at- mospheric oxidations of sulfur dioxide SO2 and nitrogen oxides mobile sources comes from the combustion of sulfur compounds in fuel. The U.S. is in the process of reducing sulfur in fuel for all mobile sources. This process begins with ultralow sulfur on-road diesel

  20. Catalytic Combustion for Ultra-Low NOx Hydrogen Turbines

    SciTech Connect (OSTI)

    Etemad, Shahrokh; Baird, Benjamin; Alavandi, Sandeep

    2011-06-30T23:59:59.000Z

    Precision Combustion, Inc., (PCI) in close collaboration with Solar Turbines, Incorporated, has developed and demonstrated a combustion system for hydrogen fueled turbines that reduces NOx to low single digit level while maintaining or improving current levels of efficiency and eliminating emissions of carbon dioxide. Full scale Rich Catalytic Hydrogen (RCH1) injector was developed and successfully tested at Solar Turbines, Incorporated high pressure test facility demonstrating low single digit NOx emissions for hydrogen fuel in the range of 2200F-2750F. This development work was based on initial subscale development for faster turnaround and reduced cost. Subscale testing provided promising results for 42% and 52% H2 with NOx emissions of less than 2 ppm with improved flame stability. In addition, catalytic reactor element testing for substrate oxidation, thermal cyclic injector testing to simulate start-stop operation in a gas turbine environment, and steady state 15 atm. operation testing were performed successfully. The testing demonstrated stable and robust catalytic element component life for gas turbine conditions. The benefit of the catalytic hydrogen combustor technology includes capability of delivering near-zero NOx without costly post-combustion controls and without requirement for added sulfur control. In addition, reduced acoustics increase gas turbine component life. These advantages advances Department of Energy (DOE’s) objectives for achievement of low single digit NOx emissions, improvement in efficiency vs. postcombustion controls, fuel flexibility, a significant net reduction in Integrated Gasification Combined Cycle (IGCC) system net capital and operating costs, and a route to commercialization across the power generation field from micro turbines to industrial and utility turbines.

  1. High Performance Plasma Sputtered Fuel Cell Electrodes with Ultra Low catalytic metal Loadings

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    to be reached between 2010 and 2015 are clear: the catalyst of a fuel cell can cost no more than 4 per kilowatt1 High Performance Plasma Sputtered Fuel Cell Electrodes with Ultra Low catalytic metal Loadings C in plasma fuel cell deposition devices. Pt loadings lower than 0.01 mg cm-2 have been realized. The Pt

  2. High Performance Plasma Sputtered PdPt Fuel Cell Electrodes with Ultra Low Loading

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    : the catalyst of a fuel cell can cost no more than 5/3 per kilowatt [1]. If the catalyst is platinum (~40 g-1High Performance Plasma Sputtered PdPt Fuel Cell Electrodes with Ultra Low Loading M. Mougenot1, 2 potential for the fuel cell technology to overcome the upcoming energy and resources issues in our society

  3. Delayed Linear Expansion of Two Ultra-low Expansion Dental Stones 

    E-Print Network [OSTI]

    Oppedisano, Michael

    2013-12-20T23:59:59.000Z

    The purpose of this study was to measure the linear setting expansion of two ultra-low expansion dental stones used in definitive cast/ prosthesis fabrication which claim to have very low to no setting expansion. Five specimens of each material...

  4. High rate, long-distance quantum key distribution over 250km of ultra low loss fibres

    E-Print Network [OSTI]

    D. Stucki; N. Walenta; F. Vannel; R. T. Thew; N. Gisin; H. Zbinden; S. Gray; C. R. Towery; S. Ten

    2009-03-23T23:59:59.000Z

    We present a fully automated quantum key distribution prototype running at 625 MHz clock rate. Taking advantage of ultra low loss fibres and low-noise superconducting detectors, we can distribute 6,000 secret bits per second over 100 km and 15 bits per second over 250km.

  5. Delayed Linear Expansion of Two Ultra-low Expansion Dental Stones

    E-Print Network [OSTI]

    Oppedisano, Michael

    2013-12-20T23:59:59.000Z

    The purpose of this study was to measure the linear setting expansion of two ultra-low expansion dental stones used in definitive cast/ prosthesis fabrication which claim to have very low to no setting expansion. Five specimens of each material...

  6. Ultra-low repetition rate mode-locked fiber laser with high-energy pulses

    E-Print Network [OSTI]

    Kobtsev, Sergei M.

    to ultra-short record high-energy pulses out of laser oscillators," Phys. Lett. A 372, 3124­3128 (2008). 5Ultra-low repetition rate mode-locked fiber laser with high-energy pulses Sergey Kobtsev* , Sergey Kukarin, Yurii Fedotov Laser Systems Laboratory, Novosibirsk State University,Pirigova 2, Novosibirsk

  7. Ultra-Low Voltage VCO Design Using Schmitt Trigger on SOI

    E-Print Network [OSTI]

    Ayers, Joseph

    , and self-heating effect. In order to reduce this disadvantage, several techniques for body-contact haveUltra-Low Voltage VCO Design Using Schmitt Trigger on SOI Kyung Ki Kim Department of Electrical of Electrical and Computer Engineering Northeastern University Boston, U.S.A ybk@ece.neu.edu Young Jun Lee Next

  8. Development of Ultra-low Platinum Alloy C th d C t l t f PEM F l C ll

    E-Print Network [OSTI]

    Development of Ultra-low Platinum Alloy C th d C t l t f PEM F l C ll Cathode Catalyst for PEM Objectives · Ultra-low loading Pt catalyysts for oxygen reduction reaction with higgh activityyand ggoodg yg Definition ­ In Developing Low Loading Platinum Catalysts · C l PCatalyst Perfformance ¾ Platinum

  9. EVALUATION OF EFFICACY AND HUMAN HEALTH RISK OF AERIAL ULTRA-LOW VOLUME APPLICATIONS OF PYRETHRINS AND

    E-Print Network [OSTI]

    Peterson, Robert K. D.

    EVALUATION OF EFFICACY AND HUMAN HEALTH RISK OF AERIAL ULTRA-LOW VOLUME APPLICATIONS OF PYRETHRINS). A human health risk assessment conducted by Peterson et al. (2006) for truck-mounted ultra-low volume (ULV to epidemic levels and dispersed to all 58 counties in the state, and was associated with low

  10. A 65nm CMOS Ultra Low Power and Low Noise 131M Front-End Transimpedance Amplifier

    E-Print Network [OSTI]

    Ayers, Joseph

    A 65nm CMOS Ultra Low Power and Low Noise 131M Front-End Transimpedance Amplifier Jiaping Hu and simulation of a high-transimpedance gain, ultra low-power dissipation and low-noise CMOS front- end control [3]. However, it introduces design challenges in the form of trade-offs between noise, power

  11. Process simulation, integration and optimization of blending of petrodiesel with biodiesel 

    E-Print Network [OSTI]

    Wang, Ting

    2009-05-15T23:59:59.000Z

    With the increasing stringency on sulfur content in petrodiesel, there is a growing tendency of broader usage of ultra low sulfur diesel (ULSD) with sulfur content of 15 ppm. Refineries around the world should develop cost-effective and sustainable...

  12. Multi-Gate Modulation Doped In0.7Ga0.3As Quantum Well FET for Ultra Low Power Digital Logic

    E-Print Network [OSTI]

    Yener, Aylin

    Multi-Gate Modulation Doped In0.7Ga0.3As Quantum Well FET for Ultra Low Power Digital Logic L. LiuQFET is promising device architecture for future ultra low power information processing applications. Introduction for reconfigurable and ultra-low-power binary decision diagram (BDD) logic ECS Transactions, 35 (3) 311-317 (2011) 10

  13. A Baseband Ultra-Low Noise SiGe:C BiCMOS 0.25 m Amplifier And Its Application For

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    A Baseband Ultra-Low Noise SiGe:C BiCMOS 0.25 µm Amplifier And Its Application For An On-Chip Phase of an ultra-low noise operational amplifier is presented. Its applications are integrated low-frequency noise and ultra low input noise to achieve the required signal to noise ratio. In these instrumentation

  14. Ultra low-mass star and substellar formation in sigma Orionis

    E-Print Network [OSTI]

    J. A. Caballero

    2005-11-07T23:59:59.000Z

    The nearby young sigma Orionis cluster (~360 pc, ~3 Ma) is becoming one of the most important regions for the study of ultra low-mass star formation and its extension down to the mass regimes of the brown dwarfs and planetary-mass objects. Here, I introduce the sigma Orionis cluster and present three studies that the JOVIAN group is developing: a pilot programme of near-infrared adaptive-optics imaging, intermediate-resolution optical spectroscopy of a large sample of stars of the cluster and a study of the mass function down to the planetary-mass domain. This paper is a summary of the content of four posters that I presented in the Ultra low-mass star formation and evolution Workshop, as single author or on behalf of different collaborations.

  15. Diffuse Surface Scattering in the Plasmonic Resonances of Ultra-Low Electron Density Nanospheres

    E-Print Network [OSTI]

    Monreal, R Carmina; Apell, S Peter

    2015-01-01T23:59:59.000Z

    Localized surface plasmon resonances (LSPRs) have recently been identified in extremely diluted electron systems obtained by doping semiconductor quantum dots. Here we investigate the role that different surface effects, namely electronic spill-out and diffuse surface scattering, play in the optical properties of these ultra-low electron density nanosystems. Diffuse scattering originates from imperfections or roughness at a microscopic scale on the surface. Using an electromagnetic theory that describes this mechanism in conjunction with a dielectric function including the quantum size effect, we find that the LSPRs show an oscillatory behavior both in position and width for large particles and a strong blueshift in energy and an increased width for smaller radii, consistent with recent experimental results for photodoped ZnO nanocrystals. We thus show that the commonly ignored process of diffuse surface scattering is a more important mechanism affecting the plasmonic properties of ultra-low electron density ...

  16. Integrated production/use of ultra low-ash coal, premium liquids and clean char

    SciTech Connect (OSTI)

    Kruse, C.W.

    1991-01-01T23:59:59.000Z

    This integrated, multi-product approach for utilizing Illinois coal starts with the production of ultra low-ash coal and then converts it to high-vale, coal-derived, products. The ultra low-ash coal is produced by solubilizing coal in a phenolic solvent under ChemCoal{trademark} process conditions, separating the coal solution from insoluble ash, and then precipitating the clean coal by dilution of the solvent with methanol. Two major products, liquids and low-ash char, are then produced by mild gasification of the low-ash coal. The low ash-char is further upgraded to activated char, and/or an oxidized activated char which has catalytic properties. Characterization of products at each stage is part of this project.

  17. Ultra-low phase noise all-optical microwave generation setup based on commercial devices

    E-Print Network [OSTI]

    Didier, A; Grop, S; Dubois, B; Bigler, E; Rubiola, E; Lacroûte, C; Kersalé, Y

    2015-01-01T23:59:59.000Z

    In this paper, we present a very simple design based on commercial devices for the all-optical generation of ultra-low phase noise microwave signals. A commercial, fibered femtosecond laser is locked to a laser that is stabilized to a commercial ULE Fabry-Perot cavity. The 10 GHz microwave signal extracted from the femtosecond laser output exhibits a single sideband phase noise $\\mathcal{L}(f)=-104 \\ \\mathrm{dBc}/\\mathrm{Hz}$ at 1 Hz Fourier frequency, at the level of the best value obtained with such "microwave photonics" laboratory experiments \\cite{Fortier2011}. Close-to-the-carrier ultra-low phase noise microwave signals will now be available in laboratories outside the frequency metrology field, opening up new possibilities in various domains.

  18. Impact of picolitre droplets on superhydrophobic surfaces with ultra-low spreading ratios

    E-Print Network [OSTI]

    Brown, P.S.; Berson, A.; Talbot, E.L.; Wood, T.J.; Schofield, W.C.E.; Bain, C.D.; Badyal, J.P.S.

    2011-01-01T23:59:59.000Z

    :24 1 IMPACT OF PICOLITRE DROPLETS ON SUPERHYDROPHOBIC SURFACES WITH ULTRA-LOW SPREADING RATIOS P. S. Brown, A. Berson, E. L. Talbot, T. J. Wood, W. C. E. Schofield, C. D. Bain†, and J. P. S. Badyal†* Department of Chemistry Science... the dynamics of wetting to be precisely controlled. Final spreading ratios as low as 0.63 can be achieved. Comparison of the maximum spreading ratio and droplet oscillation frequencies with models described in the literature shows that both are found...

  19. CASCADES: An Ultra-Low-Background Germanium Crystal Array at Pacific Northwest National Laboratory

    SciTech Connect (OSTI)

    Keillor, M. E.; Aalseth, C. E.; Day, A. R.; Erikson, L. E.; Fast, J. E.; Glasgow, B. D.; Hoppe, E. W.; Hossbach, T. W.; Hyronimus, B. J.; Miley, H. S.; Myers, A. W.; Seifert, A.; Stavenger, T. J. [Pacific Northwest National Laboratory, P.O. Box 999, Richland, Washington 99352 (United States)

    2011-12-13T23:59:59.000Z

    State-of-the-art treaty verification techniques, environmental surveillance, and physics experiments require increased sensitivity for detecting and quantifying radionuclides of interest. This can be accomplished with new detector designs that establish high detection efficiency and reduced instrument backgrounds. Current research is producing an intrinsic germanium (HPGe) array designed for high detection efficiency, ultra-low-background performance, and sensitive {gamma}--{gamma} coincidence detection. The system design is optimized to accommodate filter paper samples, e.g. samples collected by the Radionuclide Aerosol Sampler/Analyzer. The system will provide high sensitivity for weak collections on atmospheric filter samples (e.g.<10{sup 5} fissions) as well as offering the potential to gather additional information from higher activity filters using gamma cascade coincidence detection. The first of two HPGe crystal arrays in ultra-low-background vacuum cryostats has been assembled, with the second in progress. Traditional methods for constructing ultra-low-background detectors were followed, including use of materials known to be low in radioactive contaminants, use of ultra-pure reagents, and clean room assembly. The cryostat is constructed mainly from copper electroformed into near-final geometry at Pacific Northwest National Laboratory. Details of the detector assembly and initial background and spectroscopic measurement results are presented; also a description of the custom analysis package used by this project is given.

  20. CASCADES: An Ultra-Low-Background Germanium Crystal Array at Pacific Northwest National Laboratory

    SciTech Connect (OSTI)

    Keillor, Martin E.; Aalseth, Craig E.; Day, Anthony R.; Erikson, Luke E.; Fast, James E.; Glasgow, Brian D.; Hoppe, Eric W.; Hossbach, Todd W.; Hyronimus, Brian J.; Miley, Harry S.; Myers, Allan W.; Seifert, Allen; Stavenger, Timothy J.

    2011-07-14T23:59:59.000Z

    State-of-the-art treaty verification techniques, environmental surveillance, and physics experiments require increased sensitivity for detecting and quantifying radionuclides of interest. This can be accomplished with new detector designs that establish high detection efficiency and reduced instrument backgrounds. Current research is producing an intrinsic germanium (HPGe) array designed for high detection efficiency, ultra-low-background performance, and sensitive {gamma}-{gamma} coincidence detection. The system design is optimized to accommodate filter paper samples, e.g., samples collected by the Radionuclide Aerosol Sampler/Analyzer. The system will provide high sensitivity for weak collections on atmospheric filter samples (e.g., < 10{sup 5} fissions), as well as offering the potential to gather additional information from higher activity filters using gamma cascade coincidence detection. The first of two HPGe crystal arrays in ultra-low-background vacuum cryostats has been assembled, with the second in progress. Traditional methods for constructing ultra-low-background detectors were followed, including use of materials known to be low in radioactive contaminants, use of ultra-pure reagents, and clean room assembly. The cryostat is constructed mainly from copper electroformed into near-final geometry at Pacific Northwest National Laboratory. Details of the detector assembly and initial background and spectroscopic measurement results are presented; also a description of the custom analysis package used by this project is given.

  1. Measurement of Untruncated Nuclear Spin Interactions via Zero- to Ultra-Low-Field Nuclear Magnetic Resonance

    E-Print Network [OSTI]

    John W. Blanchard; Tobias F. Sjolander; Jonathan P. King; Micah P. Ledbetter; Emma H. Levine; Vikram S. Bajaj; Dmitry Budker; Alexander Pines

    2015-07-09T23:59:59.000Z

    Zero- to ultra-low-field nuclear magnetic resonance (ZULF NMR) provides a new regime for the measurement of nuclear spin-spin interactions free from effects of large magnetic fields, such as truncation of terms that do not commute with the Zeeman Hamiltonian. One such interaction, the magnetic dipole-dipole coupling, is a valuable source of spatial information in NMR, though many terms are unobservable in high-field NMR, and the coupling averages to zero under isotropic molecular tumbling. Under partial alignment, this information is retained in the form of so-called residual dipolar couplings. We report zero- to ultra-low-field NMR measurements of residual dipolar couplings in acetonitrile-2-$^{13}$C aligned in stretched polyvinyl acetate gels. This represents the first investigation of dipolar couplings as a perturbation on the indirect spin-spin $J$-coupling in the absence of an applied magnetic field. As a consequence of working at zero magnetic field, we observe terms of the dipole-dipole coupling Hamiltonian that are invisible in conventional high-field NMR. This technique expands the capabilities of zero- to ultra-low-field NMR and may have applications in precision measurement of subtle physical interactions, chemical analysis, and characterization of local mesoscale structure in materials.

  2. Frey, H.C., H.W. Choi, and K. Kim, "Measurement of the Energy Use and Emissions of Passenger Rail Locomotives Using a Portable Emission Measurement System," Paper 2009-A-243-AWMA, Proceedings, 102nd Annual Conference and Exhibition,

    E-Print Network [OSTI]

    Frey, H. Christopher

    using ultra-low sulfur diesel (ULSD) fuel. In collaboration with the locomotive owner and operator for locomotives, and to characterize baseline emission rates for three selected locomotives operated on ultra low sulfur diesel. The selected locomotives are a GP40 and two F59s, owned and operated by the North Carolina

  3. Methodology for Formulating Diesel Surrogate Fuels with Accurate Compositional, Ignition-Quality, and Volatility Characteristics

    SciTech Connect (OSTI)

    Mueller, Charles J.; Cannella, William J.; Bruno, Thomas J.; Bunting, Bruce G.; Dettman, Heather; Franz, James A.; Huber, Marcia L.; Natarajan, Mani; Pitz, William J.; Ratcliff, Matthew A.; Wright, Ken

    2012-07-26T23:59:59.000Z

    In this study, a novel approach was developed to formulate surrogate fuels having characteristics that are representative of diesel fuels produced from real-world refinery streams. Because diesel fuels typically consist of hundreds of compounds, it is difficult to conclusively determine the effects of fuel composition on combustion properties. Surrogate fuels, being simpler representations of these practical fuels, are of interest because they can provide a better understanding of fundamental fuel-composition and property effects on combustion and emissions-formation processes in internal-combustion engines. In addition, the application of surrogate fuels in numerical simulations with accurate vaporization, mixing, and combustion models could revolutionize future engine designs by enabling computational optimization for evolving real fuels. Dependable computational design would not only improve engine function, it would do so at significant cost savings relative to current optimization strategies that rely on physical testing of hardware prototypes. The approach in this study utilized the stateof- the-art techniques of 13C and 1H nuclear magnetic resonance spectroscopy and the advanced distillation curve to characterize fuel composition and volatility, respectively. The ignition quality was quantified by the derived cetane number. Two wellcharacterized, ultra-low-sulfur #2 diesel reference fuels produced from refinery streams were used as target fuels: a 2007 emissions certification fuel and a Coordinating Research Council (CRC) Fuels for Advanced Combustion Engines (FACE) diesel fuel. A surrogate was created for each target fuel by blending eight pure compounds. The known carbon bond types within the pure compounds, as well as models for the ignition qualities and volatilities of their mixtures, were used in a multiproperty regression algorithm to determine optimal surrogate formulations. The predicted and measured surrogate-fuel properties were quantitatively compared to the measured target-fuel properties, and good agreement was found. This paper is dedicated to the memory of our friend and colleague Jim Franz. Funding for this research was provided by the U.S. Department of Energy (U.S. DOE) Office of Vehicle Technologies, and by the Coordinating Research Council (CRC) and the companies that employ the CRC members. The study was conducted under the auspices of CRC. The authors thank U.S. DOE program manager Kevin Stork for supporting the participation of the U.S. national laboratories in this study.

  4. Investigation of the Effects of Fuels and Aftertreatment Devices...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Matter Emissions from Catalyzed Trap-Equipped Heavy-duty Diesel Vehicles Operating on Ultra-low Sulfur EC-D Fuel ARB's Study of Emissions from Diesel and CNG Heavy-duty Transit...

  5. Jump Chaotic Behaviour of Ultra Low Loss Bulk Acoustic Wave Cavities

    E-Print Network [OSTI]

    Maxim Goryachev; Warrick G. Farr; Serge Galliou; Michael E. Tobar

    2014-06-16T23:59:59.000Z

    We demonstrate a previously unobserved nonlinear phenomenon in an ultra-low loss quartz Bulk Acoustic Wave cavity ($Q>3\\times10^9$), which only occurs below 20 milli-Kelvin in temperature and under relatively weak pumping. The phenomenon reveals the emergence of several stable equilibria (at least two foci and two nodes) and jumps between these quasi states at random times. The degree of this randomness as well as separations between levels can be controlled by the frequency of the incident carrier signal. It is demonstrated that the nature of the effect lays beyond the standard Duffing model.

  6. Ultra-low field nuclear magnetic resonance and magnetic resonance imaging to discriminate and identify materials

    SciTech Connect (OSTI)

    Matlashov, Andrei Nikolaevich; Urbaitis, Algis V.; Savukov, Igor Mykhaylovich; Espy, Michelle A.; Volegov, Petr Lvovich; Kraus, Jr., Robert Henry

    2013-03-05T23:59:59.000Z

    Method comprising obtaining an NMR measurement from a sample wherein an ultra-low field NMR system probes the sample and produces the NMR measurement and wherein a sampling temperature, prepolarizing field, and measurement field are known; detecting the NMR measurement by means of inductive coils; analyzing the NMR measurement to obtain at least one measurement feature wherein the measurement feature comprises T1, T2, T1.rho., or the frequency dependence thereof; and, searching for the at least one measurement feature within a database comprising NMR reference data for at least one material to determine if the sample comprises a material of interest.

  7. High excitation power photoluminescence studies of ultra-low density GaAs quantum dots

    SciTech Connect (OSTI)

    Sonnenberg, D.; Graf, A.; Paulava, V.; Heyn, Ch.; Hansen, W. [Institut für Angewandte Physik und Zentrum für Mikrostrukturforschung, Universität Hamburg, Jungiusstr. 11, 20355 Hamburg (Germany)

    2013-12-04T23:59:59.000Z

    We fabricate GaAs epitaxial quantum dots (QDs) by filling of self-organized nanoholes in AlGaAs. The QDs are fabricated under optimized process conditions and have ultra-low density in the 10{sup 6} cm{sup ?2} regime. At low excitation power the optical emission of single QDs exhibit sharp excitonic lines, which are attributed to the recombination of excitonic and biexcitonic states. High excitation power measurements reveal surprisingly broad emission lines from at least six QD shell states.

  8. Natural Theories of Ultra-Low Mass PNGB's: Axions and Quintessence

    E-Print Network [OSTI]

    Christopher T. Hill; Adam K. Leibovich

    2002-06-06T23:59:59.000Z

    We consider the Wilson Line PNGB which arises in a U(1)^N gauge theory, abstracted from a latticized, periodically compactified extra dimension U(1). Planck scale breaking of the PNGB's global symmetry is suppressed, providing natural candidates for the axion and quintessence. We construct an explicit model in which the axion may be viewed as the 5th component of the U(1)_Y gauge field in a 1+4 latticized periodically compactified extra dimension. We also construct a quintessence PNGB model where the ultra-low mass arises from Planck-scale suppressed physics itself.

  9. Measurements of ultra-low-energy electron scattering cross sections of atoms and molecules

    SciTech Connect (OSTI)

    Kitajima, M.; Shigemura, K.; Kurokawa, M. [Department of Chemistry, Tokyo Institute of Technology, 152-8551 Tokyo (Japan); Odagiri, T. [Department of Physics, Sophia University, 102-8554 Tokyo, Japan and Department of Chemistry, Tokyo Institute of Technology, 152-8551 Tokyo (Japan); Kato, H.; Hoshino, M.; Tanaka, H. [Department of Physics, Sophia University, 102-8554 Tokyo (Japan); Ito, K. [Photon Factory, Institute of Materials Structure Science, 305-0801 Tsukuba (Japan)

    2014-03-05T23:59:59.000Z

    A new experimental technique for the total cross section measurements of ultra-low energy electron collisions with atoms and molecules utilizing the synchrotron radiation is presented. The technique employs a combination of the penetrating field technique and the threshold photoionization of rare gas atoms using the synchrotron radiation as an electron source in order to produce a high resolution electron beam at very low energy. Absolute total cross sections for electron scattering from He, Ne, Ar, Kr, and Xe in the energy region from extremely low electron energy to 20 eV are presented.

  10. Specifications of the octupole magnets required for the ATF2 ultra-low ß* lattice

    SciTech Connect (OSTI)

    Marin, E.; /SLAC; Modena, M.; /CERN; Tauchi, T.; Terunuma, N.; /KEK, Tsukuba; Tomas, R.; /CERN; White, G.R.; /SLAC

    2014-05-28T23:59:59.000Z

    The Accelerator Test Facility 2 (ATF2) aims to test the novel chromaticity correction for higher chromaticity lattices as the one of CLIC. To this end the ATF2 ultra-low ß* lattice is designed to vertically focus the beam at the focal point or usually referred to as interaction point (IP), down to 23 nm. However when the measured multipole components of the ATF2 magnets are considered in the simulations, the evaluated spot sizes at the IP are well above the design value. The designed spot size is effectively recovered by inserting a pair of octupole magnets. In this note we address the technical specifications required for these octupole magnets.

  11. Ultra-Low-Energy Germanium Detector for Neutrino-Nucleus Coherent Scattering and Dark Matter Searches

    E-Print Network [OSTI]

    Henry T. Wong

    2008-03-01T23:59:59.000Z

    The status and plans of a research program on the development of ultra-low-energy germanium detectors with sub-keV sensitivities are reported. We survey the scientific goals which include the observation of neutrino-nucleus coherent scattering, the studies of neutrino magnetic moments, as well as the searches of WIMP dark matter. In particular, a threshold of 100-200 eV and a sub-keV background comparable to underground experiments were achieved with prototype detectors. New limits were set for WIMPs with mass between 3-6 GeV. The prospects of the realization of full-scale experiments are discussed.

  12. Coherent-feedback control strategy to suppress spontaneous switching in ultra-low power optical bistability

    E-Print Network [OSTI]

    Hideo Mabuchi

    2011-01-18T23:59:59.000Z

    An optical resonator with intracavity Kerr nonlinearity can exhibit dispersive bistability suitable for all-optical switching. With nanophotonic elements it may be possible to achieve attojoule switching energies, which would be very attractive for ultra-low power operation but potentially problematic because of quantum fluctuation-induced spontaneous switching. In this manuscript I derive a quantum-optical model of two Kerr-nonlinear ring resonators connected in a coherent feedback loop, and show via numerical simulation that a properly designed `controller' cavity can significantly reduce the spontaneous switching rate of a bistable `plant' cavity in a completely embedded and autonomous manner.

  13. The Majorana experiment: an ultra-low background search for neutrinoless double-beta decay

    E-Print Network [OSTI]

    D. G. Phillips II; E. Aguayo; F. T. Avignone III; H. O. Back; A. S. Barabash; M. Bergevin; F. E. Bertrand; M. Boswell; V. Brudanin; M. Busch; Y. -D. Chan; C. D. Christofferson; J. I. Collar; D. C. Combs; R. J. Cooper; J. A. Detwiler; P. J. Doe; Y. Efremenko; V. Egorov; H. Ejiri; S. R. Elliott; J. Esterline; J. E. Fast; N. Fields; P. Finnerty; F. M. Fraenkle; V. M. Gehman; G. K. Giovanetti; M. P. Green; V. E. Guiseppe; K. Gusey; A. L. Hallin; R. Hazama; R. Henning; A. Hime; E. W. Hoppe; M. Horton; S. Howard; M. A. Howe; R. A. Johnson; K. J. Keeter; C. Keller; M. F. Kidd; A. Knecht; O. Kochetov; S. I. Konovalov; R. T. Kouzes; B. LaFerriere; B. H. LaRoque; J. Leon; L. E. Leviner; J. C. Loach; S. MacMullin; M. G. Marino; R. D. Martin; D. -M. Mei; J. Merriman; M. L. Miller; L. Mizouni; M. Nomachi; J. L. Orrell; N. R. Overman; A. W. P. Poon; G. Perumpilly; G. Prior; D. C. Radford; K. Rielage; R. G. H. Robertson; M. C. Ronquest; A. G. Schubert; T. Shima; M. Shirchenko; K. J. Snavely; D. Steele; J. Strain; K. Thomas; V. Timkin; W. Tornow; I. Vanyushin; R. L. Varner; K. Vetter; K. Vorren; J. F. Wilkerson; B. A. Wolfe; E. Yakushev; A. R. Young; C. -H. Yu; V. Yumatov; C. Zhang

    2011-11-23T23:59:59.000Z

    The observation of neutrinoless double-beta decay would resolve the Majorana nature of the neutrino and could provide information on the absolute scale of the neutrino mass. The initial phase of the Majorana experiment, known as the Demonstrator, will house 40 kg of Ge in an ultra-low background shielded environment at the 4850' level of the Sanford Underground Laboratory in Lead, SD. The objective of the Demonstrator is to determine whether a future 1-tonne experiment can achieve a background goal of one count per tonne-year in a narrow region of interest around the 76Ge neutrinoless double-beta decay peak.

  14. The MAJORANA experiment: an ultra-low background search for neutrinoless double-beta decay

    SciTech Connect (OSTI)

    Phillips, D.; Aguayo Navarrete, Estanislao; Avignone, Frank T.; Back, Henning O.; Barabash, Alexander S.; Bergevin, M.; Bertrand, F.; Boswell, M.; Brudanin, V.; Busch, Matthew; Chan, Yuen-Dat; Christofferson, Cabot-Ann; Collar, J. I.; Combs, Dustin C.; Cooper, R. J.; Detwiler, Jason A.; Doe, Peter J.; Efremenko, Yuri; Egorov, Viatcheslav; Ejiri, H.; Elliott, Steven R.; Esterline, James H.; Fast, James E.; Fields, N.; Finnerty, P.; Fraenkle, Florian; Gehman, Victor; Giovanetti, G. K.; Green, Matthew P.; Guiseppe, Vincente; Gusey, K.; Hallin, A. L.; Hazama, R.; Henning, Reyco; Hime, Andrew; Hoppe, Eric W.; Horton, Mark; Howard, Stanley; Howe, M. A.; Johnson, R. A.; Keeter, K.; Keller, C.; Kidd, Mary; Knecht, A.; Kochetov, Oleg; Konovalov, S.; Kouzes, Richard T.; LaFerriere, Brian D.; LaRoque, B. H.; Leon, Jonathan D.; Leviner, L.; Loach, J. C.; MacMullin, S.; Marino, Michael G.; Martin, R. D.; Mei, Dong-Ming; Merriman, Jason H.; Miller, M. L.; Mizouni, Leila; Nomachi, Masaharu; Orrell, John L.; Overman, Nicole R.; Poon, Alan; Perumpilly, Gopakumar; Prior, Gersende; Radford, D. C.; Rielage, Keith; Robertson, R. G. H.; Ronquest, M. C.; Schubert, Alexis G.; Shima, T.; Shirchenko, M.; Snavely, Kyle J.; Steele, David; Strain, J.; Thomas, K.; Timkin, V.; Tornow, W.; Vanyushin, I.; Varner, R. L.; Vetter, Kai; Vorren, Kris R.; Wilkerson, J. F.; Wolfe, B. A.; Yakushev, E.; Young, A.; Yu, Chang-Hong; Yumatov, Vladimir; Zhang, C.

    2012-12-01T23:59:59.000Z

    The observation of neutrinoless double-beta decay would resolve the Majorana nature of the neutrino and could provide information on the absolute scale of the neutrino mass. The initial phase of the Majorana Experiment, known as the Demonstrator, will house 40 kg of Ge in an ultra-low background shielded environment at the 4850' level of the Sanford Underground Laboratory in Lead, SD. The objective of the Demonstrator is to validate whether a future 1-tonne experiment can achieve a background goal of one count per tonne-year in a narrow region of interest around the 76Ge neutrinoless double-beta decay peak.

  15. Jump chaotic behaviour of ultra low loss bulk acoustic wave cavities

    SciTech Connect (OSTI)

    Goryachev, Maxim, E-mail: maxim.goryachev@uwa.edu.au; Farr, Warrick G.; Tobar, Michael E. [ARC Centre of Excellence for Engineered Quantum Systems, University of Western Australia, 35 Stirling Highway, Crawley WA 6009 (Australia); Galliou, Serge [Department of Time and Frequency, FEMTO-ST Institute, ENSMM, 26 Chemin de l'Épitaphe 25000 Besançon (France)

    2014-08-11T23:59:59.000Z

    We demonstrate a previously unobserved nonlinear phenomenon in an ultra-low loss quartz bulk acoustic wave cavity (Q>3>10{sup 9}), which only occurs below 20 mK in temperature and under relatively weak pumping. The phenomenon reveals the emergence of several stable equilibria (at least two foci and two nodes) and jumps between these quasi states at random times. The degree of this randomness as well as separations between levels can be controlled by the frequency of the incident carrier signal. It is demonstrated that the nature of the effect lies beyond the standard Duffing model.

  16. A University Consortium on Low Temperature Combustion for High Efficiency, Ultra-Low Emission Engines

    SciTech Connect (OSTI)

    Dennis N. Assanis; Arvind Atreya; Jyh-Yuan Chen; Wai K. Cheng; Robert W. Dibble; Chris Edwards; Zoran S. Filipi; Christian Gerdes; Hong Im; George A. Lavoie; Margaret S. Wooldridge

    2009-12-31T23:59:59.000Z

    The objective of the University consortium was to investigate the fundamental processes that determine the practical boundaries of Low Temperature Combustion (LTC) engines and develop methods to extend those boundaries to improve the fuel economy of these engines, while operating with ultra low emissions. This work involved studies of thermal effects, thermal transients and engine management, internal mixing and stratification, and direct injection strategies for affecting combustion stability. This work also examined spark-assisted Homogenous Charge Compression Ignition (HCCI) and exhaust after-treatment so as to extend the range and maximize the benefit of Homogenous Charge Compression Ignition (HCCI)/ Partially Premixed Compression Ignition (PPCI) operation. In summary the overall goals were: ? Investigate the fundamental processes that determine the practical boundaries of Low Temperature Combustion (LTC) engines. ? Develop methods to extend LTC boundaries to improve the fuel economy of HCCI engines fueled on gasoline and alternative blends, while operating with ultra low emissions. ? Investigate alternate fuels, ignition and after-treatment for LTC and Partially Premixed compression Ignition (PPCI) engines.

  17. Low-noise pulsed pre-polarization magnet system for ultra-low field NMR

    SciTech Connect (OSTI)

    Sims, James R [Los Alamos National Laboratory; Schilling, Josef B [Los Alamos National Laboratory; Swenson, Charles A [Los Alamos National Laboratory; Gardner, David L [Los Alamos National Laboratory; Matlashov, Andrei N [Los Alamos National Laboratory; Ammerman, Curti N [Los Alamos National Laboratory

    2009-01-01T23:59:59.000Z

    A liquid cooled, pulsed electromagnet of solenoid configuration suitable for duty in an ultra-low field nuclear magnetic resonance system has been designed, fabricated and successfully operated. The magnet design minimizes Johnson noise, minimizes the hydrogen signal and incorporates minimal metal and no ferromagnetic materials. In addition, an acoustically quiet cooling system permitting 50% duty cycle operation was achieved by designing for single-phase, laminar flow, forced convection cooling. Winding, conductor splicing and epoxy impregnation techniques were successfully developed to produce a coil winding body with integral cooling passageways and adequate structural integrity. Issues of material compatibility, housing, coolant flow system and heat rejection system design will be discussed. Additionally, this pulsed electromagnet design has been extended to produce a boiling liquid cooled version in a paired solenoid configuration suitable for duty in an ultra-low field nuclear magnetic resonance system. This pair of liquid nitrogen cooled coils is currently being tested and commissioned. Issues of material compatibility, thermal insulation, thermal contraction, housing and coolant flow design are discussed.

  18. Calibration of an ultra-low-background proportional counter for measuring {sup 37}Ar

    SciTech Connect (OSTI)

    Seifert, A.; Aalseth, C. E.; Bonicalzi, R. M.; Bowyer, T. W.; Day, A. R.; Fuller, E. S.; Haas, D. A.; Hayes, J. C.; Hoppe, E. W.; Humble, P. H.; Keillor, M. E.; LaFerriere, B. D.; Mace, E. K.; McIntyre, J. I.; Merriman, J. H.; Miley, H. S.; Myers, A. W.; Orrell, J. L.; Overman, C. T.; Panisko, M. E. [Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington, 99352 (United States)] [Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington, 99352 (United States); and others

    2013-08-08T23:59:59.000Z

    An ultra-low-background proportional counter design has been developed at Pacific Northwest National Laboratory (PNNL) using clean materials, primarily electro-chemically-purified copper. This detector, along with an ultra-low-background counting system (ULBCS), was developed to complement a new shallow underground laboratory (30 meters water-equivalent) at PNNL. The ULBCS design includes passive neutron and gamma shielding, along with an active cosmic-veto system. This system provides a capability for making ultra-sensitive measurements to support applications like age-dating soil hydrocarbons with {sup 14}C/{sup 3}H, age-dating of groundwater with {sup 39}Ar, and soil-gas assay for {sup 37}Ar to support On-Site Inspection (OSI). On-Site Inspection is a key component of the verification regime for the Comprehensive Nuclear-Test-Ban Treaty (CTBT). Measurements of radionuclides created by an underground nuclear explosion are valuable signatures of a Treaty violation. For OSI, the 35-day half-life of {sup 37}Ar, produced from neutron interactions with calcium in soil, provides both high specific activity and sufficient time for inspection before decay limits sensitivity. This work describes the calibration techniques and analysis methods developed to enable quantitative measurements of {sup 37}Ar samples over a broad range of proportional counter operating pressures. These efforts, along with parallel work in progress on gas chemistry separation, are expected to provide a significant new capability for {sup 37}Ar soil gas background studies.

  19. Controlling Low-Rate Signal Path Microdischarge for an Ultra-Low-Background Proportional Counter

    SciTech Connect (OSTI)

    Mace, Emily K.; Aalseth, Craig E.; Bonicalzi, Ricco; Day, Anthony R.; Hoppe, Eric W.; Keillor, Martin E.; Myers, Allan W.; Overman, Cory T.; Seifert, Allen

    2013-05-01T23:59:59.000Z

    ABSTRACT Pacific Northwest National Laboratory (PNNL) has developed an ultra-low-background proportional counter (ULBPC) made of high purity copper. These detectors are part of an ultra-low-background counting system (ULBCS) in the newly constructed shallow underground laboratory at PNNL (at a depth of ~30 meters water-equivalent). To control backgrounds, the current preamplifier electronics are located outside the ULBCS shielding. Thus the signal from the detector travels through ~1 meter of cable and is potentially susceptible to high voltage microdischarge and other sources of electronic noise. Based on initial successful tests, commercial cables and connectors were used for this critical signal path. Subsequent testing across different batches of commercial cables and connectors, however, showed unwanted (but still low) rates of microdischarge noise. To control this noise source, two approaches were pursued: first, to carefully validate cables, connectors, and other commercial components in this critical signal path, making modifications where necessary; second, to develop a custom low-noise, low-background preamplifier that can be integrated with the ULBPC and thus remove most commercial components from the critical signal path. This integrated preamplifier approach is based on the Amptek A250 low-noise charge-integrating preamplifier module. The initial microdischarge signals observed are presented and characterized according to the suspected source. Each of the approaches for mitigation is described, and the results from both are compared with each other and with the original performance seen with commercial cables and connectors.

  20. Residual Dipolar Couplings in Zero-to-Ultra-Low-Field Nuclear Magnetic Resonance

    E-Print Network [OSTI]

    Blanchard, John W; King, Jonathan P; Ledbetter, Micah P; Levine, Emma H; Bajaj, Vikram S; Budker, Dmitry; Pines, Alexander

    2015-01-01T23:59:59.000Z

    Zero-to-ultra-low-field nuclear magnetic resonance (ZULF-NMR) provides a new regime for the measurement of nuclear spin-spin interactions free from effects of large magnetic fields, such as truncation of terms that do not commute with the Zeeman Hamiltonian. One such interaction, the magnetic dipole-dipole coupling, is a valuable source of spatial information in NMR, though many terms are unobservable in high-field NMR, and the interaction averages to zero under isotropic molecular tumbling. Under partial orientational ordering, this information is retained in the form of so-called residual dipolar couplings. We report zero-to-ultra-low-field NMR measurements of residual dipolar couplings in acetonitrile-2-$^{13}$C aligned in stretched polyvinyl acetate gels. This represents the first investigation of dipolar couplings as a perturbation on the indirect spin-spin $J$-coupling in the absence of an applied magnetic field. As a consequence of working at zero magnetic field, we observe terms of the dipole-dipole c...

  1. 156 IEEE MICROWAVE AND WIRELESS COMPONENTS LETTERS, VOL. 14, NO. 4, APRIL 2004 An Ultra-Low Power InAs/AlSb HEMT Ka-Band

    E-Print Network [OSTI]

    Rodwell, Mark J. W.

    156 IEEE MICROWAVE AND WIRELESS COMPONENTS LETTERS, VOL. 14, NO. 4, APRIL 2004 An Ultra-Low Power dc power dissipation of the ABCS LNA was an ultra-low 1.5 mW per stage, or 4.5 mW total. This is less amplifier, mil- limeter-waves. I. INTRODUCTION ULTRA-LOW power millimeter-wave low-noise am- plifiers (LP

  2. COST-EFFECTIVE CONTROL OF NOx WITH INTEGRATED ULTRA LOW-NOx BURNERS AND SNCR

    SciTech Connect (OSTI)

    Hamid Farzan

    2001-07-01T23:59:59.000Z

    Coal-fired electric utilities are facing a serious challenge with regards to curbing their NO{sub x} emissions. At issue are the NO{sub x} contributions to the acid rain, ground level ozone, and particulate matter formation. Substantial NO{sub x} control requirements could be imposed under the proposed Ozone Transport Rule, National Ambient Air Quality Standards, and New Source Performance Standards. McDermott Technology, Inc. (MTI), Babcock and Wilcox (B and W), and Fuel Tech are teaming to provide an integrated solution for NO{sub x} control. The system will be comprised of an ultra low-NO{sub x} pulverized coal (PC) burner technology plus a urea-based, selective non-catalytic reduction (SNCR) system. This system will be capable of meeting a target emission limit of 0.15 lb NO{sub x}/10{sup 6} Btu and target ammonia (NH3) slip level targeted below 5 ppmV for commercial units. Our approach combines the best available combustion and post-combustion NO{sub x} control technologies. More specifically, B and W's DRB-4Z TM ultra low-NO{sub x} PC burner technology will be combined with Fuel Tech's NO{sub x}OUT (SNCR) and NO{sub x}OUT Cascade (SNCR/SCR hybrid) systems and jointly evaluated and optimized in a state-of-the-art test facility at MTI. Although the NO{sub x}OUT Cascade (SNCR/SCR hybrid) system will not be tested directly in this program, its potential application for situations that require greater NO{sub x} reductions will be inferred from other measurements (i.e., SNCR NO{sub x} removal efficiency plus projected NO{sub x} reduction by the catalyst based on controlled ammonia slip). Our analysis shows that the integrated ultra low-NO{sub x} burner and SNCR system has the lowest cost when the burner emissions are 0.25 lb NO{sub x}/10{sup 6} Btu or less. At burner NO{sub x} emission level of 0.20 lb NO{sub x}/10{sup 6} Btu, the levelized cost per ton of NO{sub x} removed is 52% lower than the SCR cost.

  3. Exploring Low Emission Lubricants for Diesel Engines

    SciTech Connect (OSTI)

    Perez, J. M.

    2000-07-06T23:59:59.000Z

    A workshop to explore the technological issues involved with the removal of sulfur from lubricants and the development of low emission diesel engine oils was held in Scottsdale, Arizona, January 30 through February 1, 2000. It presented an overview of the current technology by means of panel discussions and technical presentations from industry, government, and academia.

  4. Ultra-low field NMR for detection and characterization of 235 UF6

    SciTech Connect (OSTI)

    Espy, Michelle A [Los Alamos National Laboratory; Magnelind, Per E [Los Alamos National Laboratory; Matlashov, Andrei N [Los Alamos National Laboratory; Urbaitis, Algis V [Los Alamos National Laboratory; Volegov, Petr L [Los Alamos National Laboratory

    2009-01-01T23:59:59.000Z

    We have demonstrated the first ultra-low field (ULF) nuclear magnetic resonance measurements of uranium hexafluoride (UF{sub 6}), both depleted and 70% enriched, which is used in the uranium enrichment process. A sensitive non-invasive detection system would have an important role in non-proliferation surveillance. A two-frequency technique was employed to remove the transients induced by rapidly switching off the 50 mT pre-polarization field. A mean transverse relaxation time T{sub 2} of 24 ms was estimated for the un-enriched UF{sub 6} sample measured at a mean temperature of 80 C. Nuclear magnetic resonance at ULF has several advantages including the ability to measure through metal, such as pipes, and simple magnetic field generation hardware. We present here recent data and discuss the potential for non-proliferation monitoring of enrichment and flow velocity.

  5. Ultra low energy results and their impact to dark matter and low energy neutrino physics

    E-Print Network [OSTI]

    E. Bougamont; P. Colas; J. Derre; I. Giomataris; G. Gerbier; M. Gros; P. Magnier; X. F. Navick; P. Salin; I. Savvidis; G. Tsiledakis; J. D. Vergados

    2010-10-20T23:59:59.000Z

    We present ultra low energy results taken with the novel Spherical Proportional Counter. The energy threshold has been pushed down to about 25 eV and single electrons are clearly collected and detected. To reach such performance low energy calibration systems have been successfully developed: - A pulsed UV lamp extracting photoelectrons from the inner surface of the detector - Various radioactive sources allowing low energy peaks through fluorescence processes. The bench mark result is the observation of a well resolved peak at 270 eV due to carbon fluorescence which is unique performance for such large-massive detector. It opens a new window in dark matter and low energy neutrino search and may allow detection of neutrinos from a nuclear reactor or from supernova via neutrino-nucleus elastic scattering

  6. Low energy conversion electron detection in superfluid He3 at ultra-low temperature

    E-Print Network [OSTI]

    E. Moulin; C. Winkelmann; J. F. Macias-Perez; Yu. M. Bunkov; H. Godfrin; D. Santos

    2005-04-12T23:59:59.000Z

    We report on the first results of the MACHe3 (MAtrix of Cells of Helium 3) prototype experiment concerning the measurement of low energy conversion electrons at ultra-low temperature. For the first time, the feasibility of the detection of low energy electrons is demonstrated in superfluid He3-B cooled down to 100 microK. Low energy electrons at 7.3 keV coming from the K shell conversion of the 14.4 keV nuclear transition of a low activity Co57 source are detected, opening the possibility to use a He3-based detector for the detection of Weakly Interacting Massive Particles (WIMPs) which are expected to release an amount of energy higher-bounded by 5.6 keV.

  7. Direct imaging of neural currents using ultra-low field magnetic resonance techniques

    DOE Patents [OSTI]

    Volegov, Petr L. (Los Alamos, NM); Matlashov, Andrei N. (Los Alamos, NM); Mosher, John C. (Los Alamos, NM); Espy, Michelle A. (Los Alamos, NM); Kraus, Jr., Robert H. (Los Alamos, NM)

    2009-08-11T23:59:59.000Z

    Using resonant interactions to directly and tomographically image neural activity in the human brain using magnetic resonance imaging (MRI) techniques at ultra-low field (ULF), the present inventors have established an approach that is sensitive to magnetic field distributions local to the spin population in cortex at the Larmor frequency of the measurement field. Because the Larmor frequency can be readily manipulated (through varying B.sub.m), one can also envision using ULF-DNI to image the frequency distribution of the local fields in cortex. Such information, taken together with simultaneous acquisition of MEG and ULF-NMR signals, enables non-invasive exploration of the correlation between local fields induced by neural activity in cortex and more `distant` measures of brain activity such as MEG and EEG.

  8. Ultra low-K shrinkage behavior when under electron beam in a scanning electron microscope

    SciTech Connect (OSTI)

    Lorut, F.; Imbert, G. [ST Microelectronics, 850 rue Jean Monnet, 38926 Crolles Cedex (France)] [ST Microelectronics, 850 rue Jean Monnet, 38926 Crolles Cedex (France); Roggero, A. [Centre National d'Etudes Spatiales, 18 Avenue Edouard Belin, 31400 Toulouse (France)] [Centre National d'Etudes Spatiales, 18 Avenue Edouard Belin, 31400 Toulouse (France)

    2013-08-28T23:59:59.000Z

    In this paper, we investigate the tendency of porous low-K dielectrics (also named Ultra Low-K, ULK) behavior to shrink when exposed to the electron beam of a scanning electron microscope. Various experimental electron beam conditions have been used for irradiating ULK thin films, and the resulting shrinkage has been measured through use of an atomic force microscope tool. We report the shrinkage to be a fast, cumulative, and dose dependent effect. Correlation of the shrinkage with incident electron beam energy loss has also been evidenced. The chemical modification of the ULK films within the interaction volume has been demonstrated, with a densification of the layer and a loss of carbon and hydrogen elements being observed.

  9. Gravity Control by means of Electromagnetic Field through Gas or Plasma at Ultra-Low Pressure

    E-Print Network [OSTI]

    Fran De Aquino

    2013-12-02T23:59:59.000Z

    It is shown that the gravity acceleration just above a chamber filled with gas or plasma at ultra-low pressure can be strongly reduced by applying an Extra Low-Frequency (ELF) electromagnetic field across the gas or the plasma. This Gravitational Shielding Effect is related to recent discovery of quantum correlation between gravitational mass and inertial mass. According to the theory samples hung above the gas or the plasma should exhibit a weight decrease when the frequency of the electromagnetic field is decreased or when the intensity of the electromagnetic field is increased. This Gravitational Shielding Effect is unprecedented in the literature and can not be understood in the framework of the General Relativity. From the technical point of view, there are several applications for this discovery; possibly it will change the paradigms of energy generation, transportation and telecommunications.

  10. A magnetically shielded room with ultra low residual field and gradient

    SciTech Connect (OSTI)

    Altarev, I.; Chesnevskaya, S.; Gutsmiedl, E.; Kuchler, F.; Lins, T.; Marino, M.; McAndrew, J.; Niessen, B.; Paul, S.; Petzoldt, G.; Singh, J.; Stoepler, R.; Stuiber, S.; Sturm, M.; Taubenheim, B. [Physikdepartment, Technische Universität München, D-85748 Garching (Germany); Babcock, E. [Jülich Center for Neutron Science, Lichtenbergstrasse 1, D-85748 Garching (Germany); Beck, D.; Sharma, S. [Physics Department, University of Illinois at Urbana-Champaign, Urbana, Illinois 61801 (United States); Burghoff, M.; Fan, I. [Physikalisch-Technische Bundesanstalt Berlin, D-10587 Berlin (Germany); and others

    2014-07-15T23:59:59.000Z

    A versatile and portable magnetically shielded room with a field of (700 ± 200) pT within a central volume of 1 m × 1 m × 1 m and a field gradient less than 300 pT/m, achieved without any external field stabilization or compensation, is described. This performance represents more than a hundredfold improvement of the state of the art for a two-layer magnetic shield and provides an environment suitable for a next generation of precision experiments in fundamental physics at low energies; in particular, searches for electric dipole moments of fundamental systems and tests of Lorentz-invariance based on spin-precession experiments. Studies of the residual fields and their sources enable improved design of future ultra-low gradient environments and experimental apparatus. This has implications for developments of magnetometry beyond the femto-Tesla scale in, for example, biomagnetism, geosciences, and security applications and in general low-field nuclear magnetic resonance (NMR) measurements.

  11. Ultra--low noise differential AC-coupled photodetector for sensitive pulse detection applications

    E-Print Network [OSTI]

    P. J. Windpassinger; M. Kubasik; M. Koschorreck; A. Boisen; N. Kjaergaard; E. S. Polzik; J. H. Mueller

    2009-03-19T23:59:59.000Z

    We report on the performance of ultra low noise differential photodetectors especially designed for probing of atomic ensembles with weak light pulses. The working principle of the detectors is described together with the analysis procedures employed to extract the photon shot noise of light pulses with $\\sim1 \\mu$s duration. As opposed to frequency response peaked detectors, our approach allows for broadband quantum noise measurements. The equivalent noise charge (ENC) for two different hardware approaches is evaluated to 280 and 340 electrons per pulse, respectively which corresponds to a dark noise equivalent photon number of $n_\\mathrm{3dB}=0.8\\cdot 10^5$ and $n_\\mathrm{3dB}=1.2\\cdot 10^5$ in the two approaches. Finally, we discuss the possibility of removing classical correlations in the output signal caused by detector imperfection by using double--correlated sampling methods.

  12. Method for fabricating an ultra-low expansion mask blank having a crystalline silicon layer

    DOE Patents [OSTI]

    Cardinale, Gregory F. (Oakland, CA)

    2002-01-01T23:59:59.000Z

    A method for fabricating masks for extreme ultraviolet lithography (EUVL) using Ultra-Low Expansion (ULE) substrates and crystalline silicon. ULE substrates are required for the necessary thermal management in EUVL mask blanks, and defect detection and classification have been obtained using crystalline silicon substrate materials. Thus, this method provides the advantages for both the ULE substrate and the crystalline silicon in an Extreme Ultra-Violet (EUV) mask blank. The method is carried out by bonding a crystalline silicon wafer or member to a ULE wafer or substrate and thinning the silicon to produce a 5-10 .mu.m thick crystalline silicon layer on the surface of the ULE substrate. The thinning of the crystalline silicon may be carried out, for example, by chemical mechanical polishing and if necessary or desired, oxidizing the silicon followed by etching to the desired thickness of the silicon.

  13. Prospects of cold dark matter searches with an ultra-low-energy germanium detector

    E-Print Network [OSTI]

    H. T. Wong

    2007-11-08T23:59:59.000Z

    The report describes the research program on the development of ultra-low-energy germanium detectors, with emphasis on WIMP dark matter searches. A threshold of 100 eV is achieved with a 20 g detector array, providing a unique probe to the low-mas WIMP. Present data at a surface laboratory is expected to give rise to comparable sensitivities with the existing limits at the $\\rm{5 - 10 GeV}$ WIMP-mass range. The projected parameter space to be probed with a full-scale, kilogram mass-range experiment is presented. Such a detector would also allow the studies of neutrino-nucleus coherent scattering and neutrino magnetic moments.

  14. Comparison of Simulated and Experimental Combustion of Biodiesel Blends in a Single Cylinder Diesel HCCI Engine

    SciTech Connect (OSTI)

    Szybist, James P [ORNL; McFarlane, Joanna [ORNL; Bunting, Bruce G [ORNL

    2007-01-01T23:59:59.000Z

    The effect of biodiesel content on homogeneous charge compression ignition (HCCI) engine performance has been investigated both experimentally and by computer simulation. Combustion experiments were performed in a single cylinder HCCI engine using blends of soy biodiesel in ultra low sulfur diesel, with concentrations ranging from 0 to 50 vol% and equivalence ratios ( ) from 0.38 to 0.48. Data from the engine tests included combustion analysis and exhaust composition analysis with standard gaseous emissions equipment. The engine utilized a custom port fuel injection strategy to provide highly premixed charges of fuel and air, making it possible to compare the results with single zone chemical kinetics simulations that were performed using CHEMKIN III, with a reaction set including 670 species and over 3000 reactions. The reaction mechanism incorporated equations for the combustion of a paraffinic fuel, n-heptane, and an oxygenated component, methyl butanoate, as well as reactions for the formation of NOx. The zero-dimensional model did a reasonably good job of predicting the HCCI combustion event, correctly predicting intake temperature effects on the phasing of both low temperature heat release (LTHR) and the main combustion event. It also did a good job of predicting the magnitude of LTHR. Differences between the simulation and experimental data included the dependence on biodiesel concentration and the duration of both LTHR and the main combustion event. The probable reasons for these differences are the changing derived cetane number (DCN) of the model fuel blend with biodiesel concentration, and the inability of the model to account for stratification of temperature and . The simulation also showed that concentrations of intermediate species produced during LTHR are dependent on the magnitude of LTHR, but otherwise the addition of biodiesel has no discernable effect.

  15. Repetitive Ultra-low Stress Induced Nanocrystallization in Amorphous Cu?Zr?Al Alloy Evidenced by in situ Nanoindentation 

    E-Print Network [OSTI]

    Liu, Y.; Jian, J.; Lee, J. H.; Wang, C.; Cao, Q. P.; Gutierrez, C.; Wang, H.; Jiang, J. Z.; Zhang, X.

    2014-05-12T23:59:59.000Z

    . In this study, we show, via in situ nanoindentation of amorphous Cu44Zr44Al12 alloy in a transmission electron microscope that the formation of nanocrystals occurred at an ultra-low stress of 0.25 GPa in the elastic deformation regime, accompanied by load...

  16. Ultra Low-Cost 3.2Gb/s Optical-Rate Reed Solomon Decoder IC Design

    E-Print Network [OSTI]

    Hung, Shih-Hao

    decoder by using a novel Just-in-Time Folding Modified Euclidean Algorithm (JIT-FMEA). The JIT- FMEA VLSI called Just-in-Time Folding Modified Euclidean Algorithm (JIT-FMEA), which can construes an ultra low of JIT-FMEA architecture can overcome the critical paths of the bottleneck in a RS decoding procedure

  17. DEVELOPMENT AND DEMONSTRATION OF AN ULTRA LOW NOx COMBUSTOR FOR GAS TURBINES

    SciTech Connect (OSTI)

    NEIL K. MCDOUGALD

    2005-04-30T23:59:59.000Z

    Alzeta Corporation has developed surface-stabilized fuel injectors for use with lean premixed combustors which provide extended turndown and ultra-low NOX emission performance. These injectors use a patented technique to form interacting radiant and blue-flame zones immediately above a selectively-perforated porous metal surface. This allows stable operation at low reaction temperatures. This technology is being commercialized under the product name nanoSTAR. Initial tests demonstrated low NOX emissions but, were limited by flashback failure of the injectors. The weld seams required to form cylindrical injectors from flat sheet material were identified as the cause of the failures. The approach for this project was to first develop new fabrication methods to produce injectors without weld seams, verify similar emissions performance to the original flat sheet material and then develop products for microturbines and small gas turbines along parallel development paths. A 37 month project was completed to develop and test a surface stabilized combustion system for gas turbine applications. New fabrication techniques developed removed a technological barrier to the success of the product by elimination of conductive weld seams from the injector surface. The injectors demonstrated ultra low emissions in rig tests conducted under gas turbine operating conditions. The ability for injectors to share a common combustion chamber allowing for deployment in annular combustion liner was also demonstrated. Some further development is required to resolve integration issues related to specific engine constraints, but the nanoSTAR technology has clearly demonstrated its low emissions potential. The overall project conclusions can be summarized: (1) A wet-laid casting method successfully eliminated weld seams from the injector surface without degrading performance. (2) Gas turbine cycle analysis identified several injector designs and control schemes to start and load engines using nanoSTAR technology. A mechanically simple single zone injector can be used in Solar Turbine's Taurus 60 engine. (3) Rig testing of single monolithic injectors demonstrated sub 3 ppmv NOX and sub 10 ppmv CO and UHC emissions (all corrected to 15% O2) at Taurus 60 full-load pressure and combustion air inlet temperature. (4) Testing of two nanoSTAR injectors in Solar Turbine's sector rig demonstrated the ability for injectors to survive when fired in close proximity at Taurus 60 full load pressure and combustion air inlet temperature. (5) Sector rig tests demonstrated emissions performance and range of operability consistent with single injector rig tests. Alzeta has committed to the commercialization of nanoSTAR injectors and has sufficient production capability to conclude development and meet initial demand.

  18. Effect of carbon coating on scuffing performance in diesel fuels

    SciTech Connect (OSTI)

    Ajayi, O. O.; Alzoubi, M. F.; Erdemir, A.; Fenske, G. R.

    2000-06-29T23:59:59.000Z

    Low-sulfur and low-aromatic diesel fuels are being introduced in order to reduce various types of emissions in diesel engines to levels in compliance with current and impending US federal regulations. The low lubricity of these fuels, however, poses major reliability and durability problems for fuel injection components that depend on diesel fuel for their lubrication. In the present study, the authors evaluated the scuff resistance of surfaces in regular diesel fuel containing 500 ppm sulfur and in Fischer-Tropsch synthetic diesel fuel containing no sulfur or aromatics. Tests were conducted with the high frequency reciprocating test rig (HFRR) using 52100 steel balls and H-13 tool-steel flats with and without Argonne's special carbon coatings. Test results showed that the sulfur-containing fuels provide about 20% higher scuffing resistance than does fuel without sulfur. Use of the carbon coating on the flat increased scuffing resistance in both regular and synthetic fuels by about ten times, as measured by the contact severity index at scuffing. Scuffing failure in tests conducted with coated surfaces did not occur until the coating had been removed by the two distinct mechanisms of spalling and wear.

  19. Infrared Spectroscopy of the Ultra Low Mass Binary Oph 162225-240515

    E-Print Network [OSTI]

    Alexis Brandeker; Ray Jayawardhana; Valentin D. Ivanov; Radostin Kurtev

    2006-10-19T23:59:59.000Z

    Binary properties are an important diagnostic of the star and brown dwarf formation processes. While wide binaries appear to be rare in the sub-stellar regime, recent observations have revealed Ophiuchus 162225-240515 (2MASS J16222521-2405139) as a likely young ultra-low-mass binary with an apparent separation of ~240 AU. Here, we present low-resolution near-infrared spectra of the pair from NTT/SOFI (R~600) and VLT/ISAAC (R~1400), covering the 1.0-2.5um spectral region. By comparing to model atmospheres from Chabrier & Baraffe and Burrows et al., we confirm the surface temperatures to be T_A = (2350+/-150) K and T_B = (2100+/-100) K for the two components of the binary, consistent with earlier estimates from optical spectra. Using gravity sensitive K I features, we find the surface gravity to be significantly lower than field dwarfs of the same spectral type, providing the best evidence so far that these objects are indeed young. However, we find that models are not sufficiently reliable to infer accurate ages/masses from surface gravity. Instead, we derive masses of M_A = 13 (+8/-4) M_J and M_B = 10 (+5/-4) M_J for the two objects using the well-constrained temperatures and assuming an age of 1-10 Myr, consistent with the full range of ages reported for the Oph region.

  20. An ultra low noise AC beam transformer for deceleration and diagnostics of low intensity beams

    E-Print Network [OSTI]

    González, C

    1999-01-01T23:59:59.000Z

    The design of a broad band ultra-low noise ferrite loaded AC beam transformer is presented. It is designed for use in the CERN Antiproton Decelerator (AD), where beams of a few 107 charges must be decelerated from 3.5 GeV/c to 100 MeV/c. It is used in the RF beam-phase loop, and for intensity and bunch shape measurements during deceleration. When the beam is debunched for cooling on magnetic flat tops, the pick-up is used for measurements of intensity and momentum distribution by means of longitudinal Schottky scans. When used as Schottky pick-up, the signal to noise ratio should be better by about 40 dB than the existing stripline based longitudinal Schottky pick-up. The integrated design of pick-up and associated low-noise amplifier is presented. The achieved noise performance of a few from 1 to 3 MHz is obtained by attaching a low-noise, high-impedance silicon JFET (junction field effect transistor) amplifier to a high-Q resonant ferrite loaded cavity, and then eliminating the resonant response by low-nois...

  1. Chemical reactions studied at ultra-low temperature in liquid helium clusters

    SciTech Connect (OSTI)

    Huisken, Friedrich; Krasnokutski, Serge A. [Laboratory Astrophysics Group of the Max Planck Institute for Astronomy at the University of Jena, Institute of Solid State Physics, Helmholtzweg 3, D-07743 Jena (Germany)

    2012-11-27T23:59:59.000Z

    Low-temperature reaction rates are important ingredients for astrophysical reaction networks modeling the formation of interstellar matter in molecular clouds. Unfortunately, such data is difficult to obtain by experimental means. In an attempt to study low-temperature reactions of astrophysical interest, we have investigated relevant reactions at ultralow temperature in liquid helium droplets. Being prepared by supersonic expansion of helium gas at high pressure through a nozzle into a vacuum, large helium clusters in the form of liquid droplets constitute nano-sized reaction vessels for the study of chemical reactions at ultra-low temperature. If the normal isotope {sup 4}He is used, the helium droplets are superfluid and characterized by a constant temperature of 0.37 K. Here we present results obtained for Mg, Al, and Si reacting with O{sub 2}. Mass spectrometry was employed to characterize the reaction products. As it may be difficult to distinguish between reactions occurring in the helium droplets before they are ionized and ion-molecule reactions taking place after the ionization, additional techniques were applied to ensure that the reactions actually occurred in the helium droplets. This information was provided by measuring the chemiluminescence light emitted by the products, the evaporation of helium atoms by the release of the reaction heat, or by laser-spectroscopic identification of the reactants and products.

  2. Progress on detection of liquid explosives using ultra-low field MRI

    SciTech Connect (OSTI)

    Espy, Michelle A [Los Alamos National Laboratory; Matlashov, Andrei N [Los Alamos National Laboratory; Volegov, Petr L [Los Alamos National Laboratory; Schuttz, Larry M [Los Alamos National Laboratory; Baguisa, Shermiyah [Los Alamos National Laboratory; Dunkerley, David [Los Alamos National Laboratory; Magnelind, Per [Los Alamos National Laboratory; Owens, Tuba [Los Alamos National Laboratory; Sandin, Henrik [Los Alamos National Laboratory; Urbaitis, Algis [Los Alamos National Laboratory

    2010-01-01T23:59:59.000Z

    Nuclear magnetic resonance (NMR) and magnetic resonance imaging (MRI) methods are widely used in medicine, chemistry and industry. Over the past several years there has been increasing interest in performing NMR and MRI in the ultra-low field (ULF) regime, with measurement field strengths of 10-100 microTesla and pre-polarization fields of 30-50 mTesla. The real-time signal-to-noise ratio for such measurements is about 100. Our group at LANL has built and demonstrated the performance of SQUID-based ULF NMR/MRI instrumentation for classification of materials and detection of liquid explosives via their relaxation properties measured at ULF, using T{sub 1}, and T{sub 2}, and T{sub 1} frequency dispersion. We are also beginning to investigate the performance of induction coils as sensors. Here we present recent progress on the applications of ULF MR to the detection of liquid explosives, in imaging and relaxometry.

  3. Kinetic Model Development for the Combustion of Particulate Matter from Conventional and Soy Methyl Ester Diesel Fuels

    SciTech Connect (OSTI)

    Strzelec, Andrea [ORNL

    2009-12-01T23:59:59.000Z

    The primary objective of this research has been to investigate how the oxidation characteristics of diesel particulate matter (PM) are affected by blending soy-based biodiesel fuel with conventional ultra low sulfur diesel (ULSD) fuel. PM produced in a light duty engine from different biodiesel-conventional fuel blends was subjected to a range of physical and chemical measurements in order to better understand the mechanisms by which fuel-related changes to oxidation reactivity are brought about. These observations were then incorporated into a kinetic model to predict PM oxidation. Nanostructure of the fixed carbon was investigated by HR-TEM and showed that particulates from biodiesel had a more open structure than particulates generated from conventional diesel fuel, which was confirmed by BET surface area measurements. Surface area evolution with extent of oxidation reaction was measured for PM from ULSD and biodiesel. Biodiesel particulate has a significantly larger surface area for the first 40% of conversion, at which point the samples become quite similar. Oxidation characteristics of nascent PM and the fixed carbon portion were measured by temperature programmed oxidation (TPO) and it was noted that increased biodiesel blending lowered the light-off temperature as well as the temperature where the peak rate of oxidation occurred. A shift in the oxidation profiles of all fuels was seen when the mobile carbon fraction was removed, leaving only the fixed carbon, however the trend in temperature advantage of the biofuel blending remained. The mobile carbon fraction was measured by temperature programmed desorption found to generally increase with increasing biodiesel blend level. The relative change in the light-off temperatures for the nascent and fixed carbon samples was found to be related to the fraction of mobile carbon. Effective Arrhenius parameters for fixed carbon oxidation were directly measured with isothermal, differential oxidation experiments. Normalizing the reaction rate to the total carbon surface area available for reaction allowed for the definition of a single reaction rate with constant activation energy (112.5 {+-} 5.8 kJ/mol) for the oxidation of PM, independent of its fuel source. A kinetic model incorporating the surface area dependence of fixed carbon oxidation rate and the impact of the mobile carbon fraction was constructed and validated against experimental data.

  4. Driving Down Diesel Emissions

    E-Print Network [OSTI]

    Harley, Robert

    2013-01-01T23:59:59.000Z

    is adapted from “Effects of Diesel Particle Filter Retro?tst’s official: exposure to diesel exhaust harms human health.its rankings, shifting diesel exhaust from a probable to a

  5. Reformulated diesel fuel

    DOE Patents [OSTI]

    McAdams, Hiramie T [Carrollton, IL; Crawford, Robert W [Tucson, AZ; Hadder, Gerald R [Oak Ridge, TN; McNutt, Barry D [Arlington, VA

    2006-03-28T23:59:59.000Z

    Reformulated diesel fuels for automotive diesel engines which meet the requirements of ASTM 975-02 and provide significantly reduced emissions of nitrogen oxides (NO.sub.x) and particulate matter (PM) relative to commercially available diesel fuels.

  6. SRC, SIA Tackle Ultra-Low Power SoC Design Challenges for 'Extreme... http://home.businesswire.com/portal/site/google/index.jsp?ndmViewId... 1 of 3 10/10/2006 11:19 PM

    E-Print Network [OSTI]

    Hempstead, Mark

    SRC, SIA Tackle Ultra-Low Power SoC Design Challenges for 'Extreme... http://home.businesswire Eastern Time SRC, SIA Tackle Ultra-Low Power SoC Design Challenges for `Extremely Scaled' Silicon via supply of talented design engineers." The Harvard entry, "Design and Implementation of an Ultra-Low

  7. EPA Diesel Update

    Broader source: Energy.gov (indexed) [DOE]

    EPA Diesel Update 2005 DEER Conference Bill Charmley EPAOffice of Transportation and Air Quality August 22, 2005 2 Overview * Implementation update on mobile source diesel...

  8. ATF2 ULTRA-LOW IP BETAS PROPOSAL R. Tomas, H. Braun, J.P. Delahaye, E. Marn, D. Schulte, F. Zimmermann, CERN

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    ATF2 ULTRA-LOW IP BETAS PROPOSAL R. Tom´as, H. Braun, J.P. Delahaye, E. Mar´n, D. Schulte, F at these ultra-low IP betas. INTRODUCTION ATF2 is a test facility with the aim of testing the FFS design that has Design 0.1 1.0 19000 ATF2 ultra-low Proposed 0.025 1.0 76000 CLIC 3TeV Design 0.09 3.5 63000 ILC Design 0

  9. DEEP DESULFURIZATION OF DIESEL FUELS BY A NOVEL INTEGRATED APPROACH

    SciTech Connect (OSTI)

    Xiaoliang Ma; Uday Turaga; Shingo Watanabe; Subramani Velu; Chunshan Song

    2004-05-01T23:59:59.000Z

    The overall objective of this project is to explore a new desulfurization system concept, which consists of efficient separation of the refractory sulfur compounds from diesel fuel by selective adsorption, and effective hydrodesulfurization of the concentrated fraction of the refractory sulfur compounds in diesel fuels. Our approaches focused on (1) selecting and developing new adsorbents for selective adsorption of sulfur or sulfur compounds in commercial diesel fuel; (2) conducting the adsorption desulfurization of model fuels and real diesel fuels by the selective-adsorption-for-removing-sulfur (PSUSARS) process over various developed adsorbents, and examining the adsorptive desulfurization performance of various adsorbents; (3) developing and evaluating the regeneration methods for various spent adsorbent; (4) developing new catalysts for hydrodesulfurization of the refractory sulfur existing in the commercial diesel fuel; (5) on the basis of the fundamental understanding of the adsorptive performance and regeneration natures of the adsorbents, further confirming and improving the conceptual design of the novel PSU-SARS process for deep desulfurization of diesel fuel Three types of adsorbents, the metal-chloride-based adsorbents, the activated nickel-based adsorbents and the metal-sulfide-based adsorbents, have been developed for selective adsorption desulfurization of liquid hydrocarbons. All of three types of the adsorbents exhibit the significant selectivity for sulfur compounds, including alkyl dibenzothiophenes (DBTs), in diesel fuel. Adsorption desulfurization of real diesel fuels (regular diesel fuel (DF), S: 325 ppmw; low sulfur diesel fuel (LSD-I), S: 47 ppmw) over the nickel-based adsorbents (A-2 and A-5) has been conducted at different conditions by using a flowing system. The adsorption capacity of DF over A-2 corresponding to an outlet sulfur level of 30 ppmw is 2.8 mg-S/g-A. The adsorption capacity of LSD-I over A-5 corresponding to the break-through point at 5.0 ppmw sulfur level is 0.35 mg-S/g-A. The spent A-5 can be regenerated by using H2 gas at a flowing rate of 40-50 ml/min, 500 C, and ambient pressure. Adsorption desulfurization of model diesel fuels over metal-sulfide-based adsorbents (A-6-1 and A-6-2) has been conducted at different temperatures to examine the capacity and selectivity of the adsorbents. A regeneration method for the spent metal-sulfide-based adsorbents has been developed. The spent A-6-1 can be easily regenerated by washing the spent adsorbent with a polar solvent followed by heating the adsorbent bed to remove the remainder solvent. Almost all adsorption capacity of the fresh A-6-1 can be recovered after the regeneration. On the other hand, a MCM-41-supported HDS catalyst was developed for deep desulfurization of the refractory sulfur compounds. The results show that the developed MCM-41-supported catalyst demonstrates consistently higher activity for the HDS of the refractory dibenzothiophenic sulfur compounds than the commercial catalyst. On the basis of the fundamental understanding of the adsorptive performance and regeneration natures of the adsorbents, the conceptual design of the novel PSU-SARS process for deep desulfurization of diesel fuel is confirmed and improved further.

  10. Effect of silicon on ultra-low temperature toughness of Nb–Ti microalloyed cryogenic pressure vessel steels

    SciTech Connect (OSTI)

    Qiu, J.A. [Hubei Collaborative Innovation Center for Advanced Steels, International Research Institute for Steel Technology, Wuhan University of Science and Technology, Wuhan 430081 (China); Wu, K.M., E-mail: wukaiming2000@yahoo.com [Hubei Collaborative Innovation Center for Advanced Steels, International Research Institute for Steel Technology, Wuhan University of Science and Technology, Wuhan 430081 (China); Li, J.H. [Hubei Collaborative Innovation Center for Advanced Steels, International Research Institute for Steel Technology, Wuhan University of Science and Technology, Wuhan 430081 (China); Research and Development Center of WISCO, Wuhan 430080 (China); Hodgson, P.D. [Hubei Collaborative Innovation Center for Advanced Steels, International Research Institute for Steel Technology, Wuhan University of Science and Technology, Wuhan 430081 (China); Institute for Frontier Materials, Deakin University, Geelong, Victoria 3220 (Australia); Hou, T.P. [Hubei Collaborative Innovation Center for Advanced Steels, International Research Institute for Steel Technology, Wuhan University of Science and Technology, Wuhan 430081 (China); Ding, Q.F. [Research and Development Center of WISCO, Wuhan 430080 (China)

    2013-09-15T23:59:59.000Z

    The effect of Si on the ultra-low temperature toughness of Nb–Ti microalloyed cryogenic pressure vessel steels was investigated by electron back-scattered diffraction and transmission electron microscope with energy dispersive spectroscopy. Equiaxed ferrite and bainite were obtained in the tempered steels with small Si additions. Nanosized Nb–Ti carbides (< 10 nm) were formed in the steel containing 0.05% Si, whereas much coarser carbides (> 30 nm) were found in the steel containing 0.47% Si. The ultra-low temperature toughness of the Nb–Ti microalloyed cryogenic pressure vessel steel was remarkably enhanced by the reduction in the Si content, which was attributed to the pre-existing iron carbide formation before the precipitation of nanosized Nb–Ti carbides during tempering. - Highlights: • Nanosized Nb-Ti carbides formed in the tempered steel with smaller Si addition. • Coarser Nb-Ti carbides formed in the tempered steel with more Si addition. • Pre-existing cememtites provide nucleation sites for Nb-Ti carbide precipitation. • Ultra-low temperature toughness was remarkably enhanced by Si content reduction.

  11. The Design of an Ultra-Low Background Thermosyphon for the Majorana Demonstrator

    SciTech Connect (OSTI)

    Aguayo Navarrete, Estanislao; Busch, Matthew; Daniels, Randy; Fast, James E.; Green, Matthew P.; Reid, Douglas J.

    2013-05-01T23:59:59.000Z

    The MAJORANA DEMONSTRATOR (MJD) is an ultra-low background neutrinoless double-beta decay (0???) experiment that will deploy up to 40 kg of high purity germanium detectors (HPGe). The goal of this experiment is to demonstrate the feasibility of building a detector array with less than 1 event/ton-year in a 4 keV region of interest around the 0??? signal. HPGe diodes, when used as ionizing radiation detectors, need to be maintained at a temperature close to that of liquid nitrogen (77 K). This work describes the R&D results of a cryogenic system capable of meeting the requirements of low background and the cooling capacity required to successfully operate such a detector system. The MJD germanium detector modules will operate at liquid nitrogen temperature to provide adequate cooling for a full range of HPGe impurity concentrations. This paper shows the experimental results obtained using a two-phase horizontal thermosyphon using liquid nitrogen as the MJD’s cooling system. The cold test shows that the proposed thermosyphon has sufficient cooling power to handle the heat load of an MJD module. Results for the temperature gradient across the thermosyphon, cooling capacity, and design considerations demonstrate that the thermosyphon can effectively remove the calculated heat load of each module of the experiment. The thermosyphon will be bolted to a cold plate from which detector strings will hang. The thermal conductivity of a mockup of the MJD bolted thermal joint is experimentally determined to be below 0.1 K/W.

  12. Educating Consumers: New Content on Diesel Vehicles, Diesel Exhaust...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Educating Consumers: New Content on Diesel Vehicles, Diesel Exhaust Fluid, and Selective Catalytic Reduction Technologies on the AFDC Educating Consumers: New Content on Diesel...

  13. Estimation of Cosmic Induced Contamination in Ultra-low Background Detector Materials

    SciTech Connect (OSTI)

    Aguayo Navarrete, Estanislao; Kouzes, Richard T.; Orrell, John L.; Berguson, Timothy J.; Greene, Austen T.

    2012-08-01T23:59:59.000Z

    Executive Summary This document presents the result of investigating a way to reliably determine cosmic induced backgrounds for ultra-low background materials. In particular, it focuses on those radioisotopes produced by the interactions with cosmic ray particles in the detector materials that act as a background for experiments looking for neutrinoless double beta decay. This investigation is motivated by the desire to determine background contributions from cosmic ray activation of the electroformed copper that is being used in the construction of the MAJORANA DEMONSTRATOR. The most important radioisotope produced in copper that contributes to the background budget is 60Co, which has the potential to deposit energy in the region of interest of this experiment. Cobalt-60 is produced via cosmic ray neutron collisions in the copper. This investigation aims to provide a method for determining whether or not the copper has been exposed to cosmic radiation beyond the threshold which the Majorana Project has established as the maximum exposure. This threshold is set by the Project as the expected contribution of this source of background to the overall background budget. One way to estimate cosmic ray neutron exposure of materials on the surface of the Earth is to relate it to the cosmic ray muon exposure. Muons are minimum-ionizing particles and the available technologies to detect muons are easier to implement than those to detect neutrons. We present the results of using a portable, ruggedized muon detector, the µ-Witness made by our research group, for determination of muon exposure of materials for the MAJORANA DEMONSTRATOR. From the muon flux measurement, this report presents a method to estimate equivalent sea-level exposure, and then infer the neutron exposure of the tracked material and thus the cosmogenic activation of the copper. This report combines measurements of the muon flux taken by the µ-Witness detector with Geant4 simulations in order to assure our understanding of the µ-Witness prototype. As a proof of concept, we present the results of using this detector with electroformed copper during its transport from Pacific Northwest National Laboratory, where the copper is grown, to the underground lab in Lead, South Dakota, where the experiment is being deployed. The development of a code to be used with the Majorana parts tracking database, designed to aid in estimating the cosmogenic activation, is also presented.

  14. untitled

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    2 Distillate + No. 4 Fuel Oil (published on Table 46). Note: In January 2007, ultra low-sulfur diesel fuel was added. Note: Totals may not equal the sum of the components due to...

  15. X:\\L6046\\Data_Publication\\Pma\\current\\ventura\\pma.vp

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    not equal the sum of the components due to rounding. Note: In January 2007, ultra low-sulfur diesel fuel was added. Source: Energy Information Administration Form EIA-782A,...

  16. untitled

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    are from the revised survey system and are consistent. Note: In January 2007, ultra low-sulfur diesel fuel was added. Sources: Energy Information Administration Forms EIA-782A,...

  17. untitled

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    not equal the sum of the components due to rounding. Note: In January 2007, ultra low-sulfur diesel fuel was added. Source: Energy Information Administration Form EIA-782A,...

  18. Concentrations and Size Distributions of Particulate Matter Emissions...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Matter Emissions from Catalyzed Trap-Equipped Heavy-duty Diesel Vehicles Operating on Ultra-low Sulfur EC-D Fuel Concentrations and Size Distributions of Particulate Matter...

  19. Northeast Gasoline Supply Reserve | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    supplements the Northeast Home Heating Oil Reserve, a one million barrel supply of ultra-low sulfur diesel, which was used for the first time by first-responders and to fill...

  20. FEATURE FOCUS: Fuels & Combustion a new dawn for

    E-Print Network [OSTI]

    economy, proponents say. Ultra-low sulfur fuel, set to become available in the United States in 2006's light-duty diesels are quiet and clean, and they provide excellent low-end torque and superior fuel

  1. History of Heating Oil Reserve Releases

    Broader source: Energy.gov [DOE]

    The Northeast Home Heating Oil Reserve (NEHHOR), a one million barrel supply of ultra low sulfur distillate (diesel), was created to build a buffer to allow commercial companies to compensate for...

  2. Comparing the Performance of SunDiesel and Conventional Diesel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    the Performance of SunDiesel and Conventional Diesel in a Light-Duty Vehicle and Engines Comparing the Performance of SunDiesel and Conventional Diesel in a Light-Duty Vehicle and...

  3. Design of Heat Exchanger for Heat Recovery in CHP Systems 

    E-Print Network [OSTI]

    Kozman, T. A.; Kaur, B.; Lee, J.

    2009-01-01T23:59:59.000Z

    monoxide by 70 percent, hydrocarbons by 60 percent, and particulate matter by 25 percent (Emissions Control : CHP Technologies Gulf Coast CHP 2007) when used with the ultra-low sulfur diesel (ULSD) fuel. Reductions are also significant with the use... are used only in conjunction with ultra-low sulfur diesel (ULSD) fuel. 3. Exhaust Gas Recirculation (EGR) ? They have a great potential for reducing NOx emissions. 4. Selective Catalytic Reduction (SCR) ? SCR cuts down high levels of NOx by reducing...

  4. Application methods and evaluations of ultra-low-volume sprays for controlling the bollworm, tobacco budworm and boll weevil 

    E-Print Network [OSTI]

    Nemec, Stanley Joseph

    1967-01-01T23:59:59.000Z

    Xgof e ~ ~ ~ ~ o e ~ F e o ~ The ultra-low volume methos of epplyieg insecticises proviaes egricxxlture sag puhiid health with 8 technique for the eppR. Ication oi' insecticides that presentlp appears to be as efficient 886 more edeoomicel then e... wes oh- teixxeg with technical ~thion upping bp aircraft at rates es low as 6 fluM ounces per cere. The ultra-los-volume msthog of s~ insedticQles has since ethueietel sxxch interest for possible uee in control of insects attaching msgr cxops...

  5. This article was published in an Elsevier journal. The attached copy is furnished to the author for non-commercial research and

    E-Print Network [OSTI]

    Azad, Abdul-Majeed

    refineries to produce ultra-low-sulfur diesel by allowing a maximum sulfur level of 15 ppm. Gasoline also://www.elsevier.com/copyright #12;Author's personal copy Development of ceria-supported sulfur tolerant nanocatalysts: Pd by steam reforming is attractive but poses great challenge since these fuels contain sulfur up to about

  6. Reactivity Controlled Compression Ignition (RCCI) Combustion on a Multi-Cylinder Light-Duty Diesel Engine

    SciTech Connect (OSTI)

    Curran, Scott [ORNL; Hanson, Reed M [ORNL; Wagner, Robert M [ORNL

    2012-01-01T23:59:59.000Z

    Reactivity controlled compression ignition is a low-temperature combustion technique that has been shown, both in computational fluid dynamics modeling and single-cylinder experiments, to obtain diesel-like efficiency or better with ultra-low nitrogen oxide and soot emissions, while operating primarily on gasoline-like fuels. This paper investigates reactivity controlled compression ignition operation on a four-cylinder light-duty diesel engine with production-viable hardware using conventional gasoline and diesel fuel. Experimental results are presented over a wide speed and load range using a systematic approach for achieving successful steady-state reactivity controlled compression ignition combustion. The results demonstrated diesel-like efficiency or better over the operating range explored with low engine-out nitrogen oxide and soot emissions. A peak brake thermal efficiency of 39.0% was demonstrated for 2600 r/min and 6.9 bar brake mean effective pressure with nitrogen oxide emissions reduced by an order of magnitude compared to conventional diesel combustion operation. Reactivity controlled compression ignition emissions and efficiency results are compared to conventional diesel combustion operation on the same engine.

  7. Digital Pulse-Shape Discrimination Applied to an Ultra-Low-Background Gas-Proportional Counting System: First Results

    SciTech Connect (OSTI)

    Aalseth, Craig E.; Day, Anthony R.; Fuller, Erin S.; Hoppe, Eric W.; Keillor, Martin E.; Mace, Emily K.; Myers, A. W.; Overman, Cory T.; Panisko, Mark E.; Seifert, Allen; Warren, Glen A.; Williams, Richard M.

    2013-05-01T23:59:59.000Z

    Abstract A new ultra-low-background proportional counter (ULBPC) design was recently developed at Pacific Northwest National Laboratory (PNNL). This design, along with an ultra-low-background counting system (ULBCS) which provides passive and active shielding with radon exclusion, has been developed to complement a new shallow underground laboratory (~30 meters water-equivalent) constructed at PNNL. After these steps to mitigate dominant backgrounds (cosmic rays, external gamma-rays, radioactivity in materials), remaining background events do not exclusively arise from ionization of the proportional counter gas. Digital pulse-shape discrimination (PSD) is thus employed to further improve measurement sensitivity. In this work, a template shape is generated for each individual sample measurement of interest, a "self-calibrating" template. Differences in event topology can also cause differences in pulse shape. In this work, the temporal region analyzed for each event is refined to maximize background discrimination while avoiding unwanted sensitivity to event topology. This digital PSD method is applied to sample and background data, and initial measurement results from a biofuel methane sample are presented in the context of low-background measurements currently being developed.

  8. DIESEL FUEL TANK FOUNDATIONS

    SciTech Connect (OSTI)

    M. Gomez

    1995-01-18T23:59:59.000Z

    The purpose of this analysis is to design structural foundations for the Diesel Fuel Tank and Fuel Pumps.

  9. 5/28/10 3:40 PMNSF Funds Ultra-Low Energy Circuits | The Fu Foundation School of Engineering & Applied Science -Columbia University Page 1 of 1http://www.engineering.columbia.edu/nsf-funds-microelectronic-systems-research

    E-Print Network [OSTI]

    Yang, Junfeng

    5/28/10 3:40 PMNSF Funds Ultra-Low Energy Circuits | The Fu Foundation School of Engineering://www.engineering.columbia.edu/nsf-funds-microelectronic-systems-research Columbia University Home Directory | Help NSF Funds Ultra-Low Energy Circuits (http://www.compeng.columbia.edu/) . The grant will fund their proposal to perform research in ultra low-power microelectronic systems, which

  10. * email: nidhi@ece.ucsb.edu phone: +1-805-893-3812 ext 202 Ultra-low contact resistance for Self-aligned HEMT structures on N-polar GaN by MBE

    E-Print Network [OSTI]

    Rodwell, Mark J. W.

    * email: nidhi@ece.ucsb.edu phone: +1-805-893-3812 ext 202 Ultra-low contact resistance for SelfN) are regrown to achieve ultra-low Ohmic contact resistance. All MBE regrowths were done on MOCVD GaN templates of InN. To summarize, ultra-low Ohmic contact resistance of 60 -µm was obtained for a self-aligned devi

  11. Diesel lube oils; Fourth dimension of diesel particulate control

    SciTech Connect (OSTI)

    Springer, K.J. (Southwest Research Institute, San Antonio, TX (US))

    1989-07-01T23:59:59.000Z

    Particulate emission control, for the HD diesel engine, has previously been considered a three-dimensional problem involving: combustion of the fuel by the engine, fuel modification, and exhaust aftertreatment. The lube oil contribution may be considered a fourth dimension of the problem. Historically, the heavy-duty engine manufacturer has met emission standards for smoke (1968 to present), CO, HC, and NOx (1974 to present) and particulates (1988 to present) through changes in engine design. This paper used the allocation method to estimate the reduction in lube oil consumption needed to meet 1991 and 1994 U.S. particulate emission standards. This analysis places the contribution of lube oil as a source of exhaust particulates into prospective with the contributions from fuel sulfur and fuel combustion. An emissions control strategy to meet future regulations is offered in which reductions from fuel modification, combustion improvement, reduced lube oil consumption, and exhaust particulate trap-catalysts are all involved.

  12. Optimal Deployment Plan of Emission Reduction Technologies for TxDOT's Construction Equipment

    E-Print Network [OSTI]

    Bari, Muhammad Ehsanul

    2010-10-12T23:59:59.000Z

    to trees, crops, plants, lakes, and animals. Therefore, air pollution is indeed a big concern for the environment (EPA 2008a). Impacts of Emissions Air pollution has significant health, environmental, and economic impacts. Inhaling polluted air... ............................................. 22 Fuel Technologies for Emissions Reductions ......................... 23 Low-Sulfur Diesel (LSD) and Ultra Low Sulfur Diesel (ULSD) ............................................................................. 23 Natural...

  13. THE FINAL SERIES OF OILS TESTED AS A POTENTIAL SOLUTION TO THE GALVESTON FERRY

    E-Print Network [OSTI]

    Texas at Austin, University of

    DOT) began using an ultra-low sulfur diesel fuel, Texas Low Emission Diesel (TxLED), in all of its diesel dithiophosphate (ZDP). This oil was chosen to examine the effects of a synthetic oil with a low ash content. EMD low-cost solution. Additionally, none of the GFO engines is still under warranty. Also, the oil

  14. Sulfuric acid-sulfur heat storage cycle

    DOE Patents [OSTI]

    Norman, John H. (LaJolla, CA)

    1983-12-20T23:59:59.000Z

    A method of storing heat is provided utilizing a chemical cycle which interconverts sulfuric acid and sulfur. The method can be used to levelize the energy obtained from intermittent heat sources, such as solar collectors. Dilute sulfuric acid is concentrated by evaporation of water, and the concentrated sulfuric acid is boiled and decomposed using intense heat from the heat source, forming sulfur dioxide and oxygen. The sulfur dioxide is reacted with water in a disproportionation reaction yielding dilute sulfuric acid, which is recycled, and elemental sulfur. The sulfur has substantial potential chemical energy and represents the storage of a significant portion of the energy obtained from the heat source. The sulfur is burned whenever required to release the stored energy. A particularly advantageous use of the heat storage method is in conjunction with a solar-powered facility which uses the Bunsen reaction in a water-splitting process. The energy storage method is used to levelize the availability of solar energy while some of the sulfur dioxide produced in the heat storage reactions is converted to sulfuric acid in the Bunsen reaction.

  15. Join Diesel: Concurrency Primitives for Diesel Peter-Michael Osera

    E-Print Network [OSTI]

    Plotkin, Joshua B.

    Join Diesel: Concurrency Primitives for Diesel Peter-Michael Osera psosera to the Diesel programming language, entitled Join Diesel. We describe the design decisions and trade-offs made in integrating these concurrency primitives into the Diesel language. We also give a typechecking algorithm

  16. First search for double beta decay of platinum by ultra-low background HP Ge gamma spectrometry

    E-Print Network [OSTI]

    P. Belli; R. Bernabei; F. Cappella; R. Cerulli; F. A. Danevich; A. Di Marco; A. Incicchitti; M. Laubenstein; S. S. Nagorny; S. Nisi; O. G. Polischuk; V. I. Tretyak

    2011-04-29T23:59:59.000Z

    A search for double beta processes in 190Pt and 198Pt was realized with the help of ultra-low background HP Ge 468 cm^3 gamma spectrometer in the underground Gran Sasso National Laboratories of the INFN (Italy). After 1815 h of data taking with 42.5 g platinum sample, T_{1/2} limits on 2beta processes in 190Pt (\\epsilon\\beta^+ and 2\\epsilon) have been established on the level of 10^{14}-10^{16} yr, 3 to 4 orders of magnitude higher than those known previously. In particular, a possible resonant double electron capture in 190Pt was restricted on the level of 2.9 \\times 10^{16} yr at 90% C.L. In addition, T_{1/2} limit on 2 beta^- decay of 198Pt (2\

  17. Plasticity and ultra-low stress induced twin boundary migration in nanotwinned Cu by in situ nanoindentation studies

    SciTech Connect (OSTI)

    Liu, Y.; Chen, Y. [Department of Materials Science and Engineering, Texas A and M University, College Station, Texas 77843 (United States); Jian, J. [Department of Electrical Engineering, Texas A and M University, College Station, Texas 77843 (United States); Wang, H. [Department of Materials Science and Engineering, Texas A and M University, College Station, Texas 77843 (United States); Department of Electrical Engineering, Texas A and M University, College Station, Texas 77843 (United States); Zhang, X., E-mail: zhangx@tamu.edu [Department of Materials Science and Engineering, Texas A and M University, College Station, Texas 77843 (United States); Department of Mechanical Engineering, Texas A and M University, College Station, Texas 77843 (United States)

    2014-06-09T23:59:59.000Z

    Nanotwinned metals have rare combinations of mechanical strength and ductility. Previous studies have shown that detwinning occurs in plastically deformed nanotwinned metals. Although molecular dynamics simulations have predicted that fine nanotwins can migrate at low stress, there is little in situ evidence to validate such predictions. Also it is unclear if detwinning occurs prior to or succeeding plastic yielding. Here, by using in situ nanoindentation in a transmission electron microscope, we show that a non-elastic detwinning process in nanotwinned Cu occurred at ultra-low indentation stress (0.1?GPa), well before the stress necessary for plastic yielding. Furthermore, the in situ nanoindentation technique allows us to differentiate dislocation-nucleation dominated microscopic yielding preceding macroscopic yielding manifested by dislocation-transmission through twin boundaries. This study thus provides further insights for understanding plasticity in nanotwinned metals at microscopic levels.

  18. First search for double beta decay of platinum by ultra-low background HP Ge gamma spectrometry

    E-Print Network [OSTI]

    Belli, P; Cappella, F; Cerulli, R; Danevich, F A; Di Marco, A; Incicchitti, A; Laubenstein, M; Nagorny, S S; Nisi, S; Polischuk, O G; Tretyak, V I

    2011-01-01T23:59:59.000Z

    A search for double beta processes in 190Pt and 198Pt was realized with the help of ultra-low background HP Ge 468 cm^3 gamma spectrometer in the underground Gran Sasso National Laboratories of the INFN (Italy). After 1815 h of data taking with 42.5 g platinum sample, T_{1/2} limits on 2beta processes in 190Pt (\\epsilon\\beta^+ and 2\\epsilon) have been established on the level of 10^{14}-10^{16} yr, 3 to 4 orders of magnitude higher than those known previously. In particular, a possible resonant double electron capture in 190Pt was restricted on the level of 2.9 \\times 10^{16} yr at 90% C.L. In addition, T_{1/2} limit on 2 beta^- decay of 198Pt (2\

  19. Regulation of Emissions from Stationary Diesel Engines (released in AEO2007)

    Reports and Publications (EIA)

    2007-01-01T23:59:59.000Z

    On July 11, 2006, the Environmental Protection Agency (EPA) issued regulations covering emissions from stationary diesel engines New Source Performance Standards that limit emissions of NOx, particulate matter, SO2, carbon monoxide, and hydrocarbons to the same levels required for nonroad diesel engines. The regulation affects new, modified, and reconstructed diesel engines. Beginning with model year 2007, engine manufacturers must specify that new engines less than 3,000 horsepower meet the same emissions standard as nonroad diesel engines. For engines greater than 3,000 horsepower, the standard will be fully effective in 2011. Stationary diesel engine fuel will also be subject to the same standard as nonroad diesel engine fuel, which reduces the sulfur content of the fuel to 500 parts per million by mid-2007 and 15 parts per million by mid-2010.

  20. ELECTRONIC FUEL INJECTION DIESEL LOCOMOTIVES

    E-Print Network [OSTI]

    Jagannatham, Aditya K.

    ELECTRONIC FUEL INJECTION FOR DIESEL LOCOMOTIVES 13 August, 2011 Diesel Loco Modernisation Works, Patiala #12;ELECTRONIC FUEL INJECTION FOR DIESEL LOCOMOTIVES A Milestone in Green Initiatives by Indian Diesel Locomotive equipped with "Electronic Fuel Injection (EFI)" was turned out by the Diesel Loco

  1. 1500 IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS--I: REGULAR PAPERS, VOL. 54, NO. 7, JULY 2007 An Ultra-Low-Power Long Range Battery/Passive

    E-Print Network [OSTI]

    Hochberg, Michael

    ); this novel dual passive and battery operation allays one of the major drawbacks of currently available active-power circuit design techniques. At 915 MHz, based on the experimentally measured tag impedance (92-j837 An Ultra-Low-Power Long Range Battery/Passive RFID Tag for UHF and Microwave Bands With a Current

  2. An Ultra Low Power System Architecture for Sensor Network Applications Mark Hempstead, Nikhil Tripathi, Patrick Mauro, Gu-Yeon Wei, David Brooks

    E-Print Network [OSTI]

    Hempstead, Mark

    An Ultra Low Power System Architecture for Sensor Network Applications Mark Hempstead, Nikhil" of this design space is a truly untethered device that operates off of energy scavenged from the ambient architecture. Our simulation results suggest one to two orders of magnitude reduction in power dissipation over

  3. Low emissions diesel fuel

    DOE Patents [OSTI]

    Compere, A.L.; Griffith, W.L.; Dorsey, G.F.; West, B.H.

    1998-05-05T23:59:59.000Z

    A method and matter of composition for controlling NO{sub x} emissions from existing diesel engines. The method is achieved by adding a small amount of material to the diesel fuel to decrease the amount of NO{sub x} produced during combustion. Specifically, small amounts, less than about 1%, of urea or a triazine compound (methylol melamines) are added to diesel fuel. Because urea and triazine compounds are generally insoluble in diesel fuel, microemulsion technology is used to suspend or dissolve the urea or triazine compound in the diesel fuel. A typical fuel formulation includes 5% t-butyl alcohol, 4.5% water, 0.5% urea or triazine compound, 9% oleic acid, and 1% ethanolamine. The subject invention provides improved emissions in heavy diesel engines without the need for major modifications.

  4. Low emissions diesel fuel

    DOE Patents [OSTI]

    Compere, Alicia L. (Knoxville, TN); Griffith, William L. (Oak Ridge, TN); Dorsey, George F. (Farragut, TN); West, Brian H. (Kingston, TN)

    1998-01-01T23:59:59.000Z

    A method and matter of composition for controlling NO.sub.x emissions from existing diesel engines. The method is achieved by adding a small amount of material to the diesel fuel to decrease the amount of NO.sub.x produced during combustion. Specifically, small amounts, less than about 1%, of urea or a triazine compound (methylol melamines) are added to diesel fuel. Because urea and triazine compounds are generally insoluble in diesel fuel, microemulsion technology is used to suspend or dissolve the urea or triazine compound in the diesel fuel. A typical fuel formulation includes 5% t-butyl alcohol, 4.5% water, 0.5% urea or triazine compound, 9% oleic acid, and 1% ethanolamine. The subject invention provides improved emissions in heavy diesel engines without the need for major modifications.

  5. Clean Air Nonroad Diesel Rule (released in AEO2005)

    Reports and Publications (EIA)

    2005-01-01T23:59:59.000Z

    On June 29, 2004, the Environmental Protection Agency issued a comprehensive final rule regulating emissions from nonroad diesel engines and sulfur content in nonroad diesel fuel. The nonroad fuel market makes up more than 18% of the total distillate pool. The rule applies to new equipment covering a broad range of engine sizes, power ratings, and equipment types. There are currently about 6 million pieces of nonroad equipment operating in the United States, and more than 650,000 new units are sold each year.

  6. Diesel prices decrease slightly

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel prices continueU.S. DieselDieselDiesel

  7. Diesel prices rise slightly

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel prices continueU.S.DieselDieselDiesel

  8. Ultra-Clean Diesel Fuel: U.S. Production and Distribution Capability

    SciTech Connect (OSTI)

    Hadder, G.R.

    2001-02-15T23:59:59.000Z

    Diesel engines have potential for use in a large number of future vehicles in the US. However, to achieve this potential, proponents of diesel engine technologies must solve diesel's pollution problems, including objectionable levels of emissions of particulates and oxides of nitrogen. To meet emissions reduction goals, diesel fuel quality improvements could enable diesel engines with advanced aftertreatment systems to achieve the necessary emissions performance. The diesel fuel would most likely have to be reformulated to be as clean as low sulfur gasoline. This report examines the small- and large-market extremes for introduction of ultra-clean diesel fuel in the US and concludes that petroleum refinery and distribution systems could produce adequate low sulfur blendstocks to satisfy small markets for low sulfur (30 parts per million) light duty diesel fuel, and deliver that fuel to retail consumers with only modest changes. Initially, there could be poor economic returns on under-utilized infrastructure investments. Subsequent growth in the diesel fuel market could be inconsistent with U.S. refinery configurations and economics. As diesel fuel volumes grow, the manufacturing cost may increase, depending upon how hydrodesulfurization technologies develop, whether significantly greater volumes of the diesel pool have to be desulfurized, to what degree other properties like aromatic levels have to be changed, and whether competitive fuel production technologies become economic. Low sulfur (10 parts per million) and low aromatics (10 volume percent) diesel fuel for the total market could require desulfurization, dearomatization, and hydrogen production investments amounting to a third of current refinery market value. The refinery capital cost component alone would be 3 cents per gallon of diesel fuel. Outside of refineries, the gas-to-liquids (GTL) plant investment cost would be 3 to 6 cents per gallon. With total projected investments of $11.8 billion (6 to 9 cents per gallon) for the U.S. Gulf Coast alone, financing, engineering, and construction and material availability are major issues that must be addressed, for both refinery and GTL investments.

  9. Diesel particles -a health hazard 1 Diesel particles

    E-Print Network [OSTI]

    Diesel particles - a health hazard 1 Diesel particles - a health hazard #12;The Danish Ecological Council - August 20042 Diesel particles - a health hazard ISBN: 87-89843-61-4 Text by: Christian Ege 33150777 Fax no.: +45 33150971 E-mail: info@ecocouncil.dk www.ecocouncil.dk #12;Diesel particles - a health

  10. The John Deere E diesel Test & Research Project

    SciTech Connect (OSTI)

    Fields, Nathan; Mitchell, William E.

    2008-09-23T23:59:59.000Z

    Three non-road Tier II emissions compliant diesel engines manufactured by John Deere were placed on a durability test plan of 2000 hours each at full load, rated speed (FLRS). The fuel was a blend of 10% fuel ethanol and 90% low sulfur #2 diesel fuel. Seven operational failures involving twenty seven fuel system components occurred prior to completion of the intended test plan. Regulated emissions measured prior to component failure indicated compliance to Tier II certification goals for the observed test experience. The program plan included operating three non-road Tier II diesel engines for 2000 hours each monitoring the regulated emissions at 500 hour intervals for changes/deterioration. The program was stopped prematurely due to number and frequency of injection system failures. The failures and weaknesses observed involved injector seat and valve wear, control solenoid material incompatibility, injector valve deposits and injector high pressure seal cavitation erosion. Future work should target an E diesel fuel standard that emphasizes minimum water content, stability, lubricity, cetane neutrality and oxidation resistance. Standards for fuel ethanol need to require water content no greater than the base diesel fuel standard. Lubricity bench test standards may need new development for E diesel.

  11. An ultra low-noise AC beam transformer and digital signal processing system for CERN's ELENA ring

    E-Print Network [OSTI]

    Angoletta, M E; Caspers, F; Federmann, S; Molendijk, J; Pedersen, F; Sanchez-Quesada, J

    2013-01-01T23:59:59.000Z

    CERN’s Extra Low ENergy Antiproton (ELENA) ring is a new synchrotron that will be commissioned in 2016 to further decelerate the antiprotons coming from CERN’s Antiproton Decelerator (AD). Essential longitudinal diagnostics required for commissioning and operation include the intensity measurement for bunched and debunched beams and the measurement of p/p for debunched beams to assess the electron cooling performance. The beam phase information is also needed by the Low-Level RF (LLRF) system. The baseline system for providing the required beam parameters and signals is based upon two ultra-low-noise AC beam transformers and associated digital signal processing. The AC beam transformers cover different frequency regions and are an adaptation to the ELENA layout of those used in the AD. Two AC beam transformers will also be installed in the extraction lines to provide beam intensity measurements. The digital signal processing will be carried out with the leadingedge hardware family used for ELENA’s L...

  12. DIESEL et CANCER Dominique Lafon

    E-Print Network [OSTI]

    Boyer, Edmond

    1/5 DIESEL et CANCER Dominique Lafon INERIS (*) De nombreuses questions se posent sur la toxicité des émissions des moteurs diesel. C'est un sujet qui a beaucoup préoccupé les scientifiques ces EMISSIONS DU DIESEL. Avant d'aborder la toxicité des émissions du diesel, un rappel de leur composition est

  13. Integrated production/use of ultra low-ash coal, premium liquids and clean char. [Quarterly] report, December 1, 1991--February 29, 1992

    SciTech Connect (OSTI)

    Kruse, C.W. [Illinois State Geological Survey, Champaign, IL (United States)

    1992-08-01T23:59:59.000Z

    The first step in the integrated, mufti-product approach for utilizing Illinois coal is the production of ultra low-ash coal. Subsequent steps convert low-ash coal to high-value, coal-derived, products. The ultra low-ash coal is produced by solubilizing coal in a phenolic solvent under ChemCoal{trademark} process conditions, separating the coal solution from insoluble ash, and then precipitating the clean coal by dilution of the solvent with methanol. Two major products, liquids and low-ash char, are then produced by mild gasification of the low-ash coal. The low ash-char is further upgraded to activated char, and/or an oxidized activated char which has catalytic properties. Characterization of products at each stage is part of this project.

  14. Integrated production/use of ultra low-ash coal, premium liquids and clean char. Technical report, September 1, 1991--November 30, 1991

    SciTech Connect (OSTI)

    Kruse, C.W.

    1991-12-31T23:59:59.000Z

    This integrated, multi-product approach for utilizing Illinois coal starts with the production of ultra low-ash coal and then converts it to high-vale, coal-derived, products. The ultra low-ash coal is produced by solubilizing coal in a phenolic solvent under ChemCoal{trademark} process conditions, separating the coal solution from insoluble ash, and then precipitating the clean coal by dilution of the solvent with methanol. Two major products, liquids and low-ash char, are then produced by mild gasification of the low-ash coal. The low ash-char is further upgraded to activated char, and/or an oxidized activated char which has catalytic properties. Characterization of products at each stage is part of this project.

  15. Conservation Research and Development/ New Ultra-Low Carbon High Strength Steels with Improved Bake Hardenability for Enhanced Stretch Formability and Dent Resistance

    SciTech Connect (OSTI)

    Anthony J. DeArdo; C. Isaac Garcia

    2003-12-15T23:59:59.000Z

    Conservation Research and Development/New Ultra-Low Carbon High Strength Steels with Improved Bake Hardenability for Enhanced Stretch Formability and Dent Resistance. The experimental work can be divided into four phases. In each phase, the materials were received or designed, processed and tested, to evaluate the BH increment or response, as a function of compositions and processing conditions. Microstructural characterization by various techniques was performed in order to gain insights into the mechanisms of flow stress increment by bake hardening.

  16. DEEP DESULFURIZATION OF DIESEL FUELS BY A NOVEL INTEGRATED APPROACH

    SciTech Connect (OSTI)

    Xiaoliang Ma; Lu Sun; Chunshan Song

    2001-09-01T23:59:59.000Z

    Due to the increasingly stricter regulations for deep reduction of fuel sulfur content, development of new deep desulfurization processes for liquid transport fuels has become one of the major challenges to the refining industry and to the production of hydrocarbon fuels for fuel cell applications. The sulfur compounds in the current transport fuels corresponding to the S level of 350-500 ppm account for only about 0.12-0.25 wt % of the fuel. The conventional hydrotreating approaches will need to increase catalyst bed volume at high-temperature and high-pressure conditions for treating 100 % of the whole fuel in order to convert the fuel mass of less than 0.25 wt %. In the present study, we are exploring a novel adsorption process for desulfurization at low temperatures, which can effectively reduce the sulfur content in gasoline, jet fuel and diesel fuel at low investment and operating cost to meet the needs for ultra-clean transportation fuels and for fuel cell applications. Some adsorbents were prepared in this study for selective adsorption of sulfur compounds in the fuels. The adsorption experiments were conducted by using a model fuel and real fuels. The results show that the adsorbent (A-1) with a transition metal compound has a significant selectivity for sulfur compounds with a saturated adsorption capacity of {approx}0.12 mol of sulfur compounds per mol of the metal compound. Most sulfur compounds existing in the current commercial gasoline, jet fuel and diesel fuel can be removed by the adsorption using adsorbent A-1. On the basis of the preliminary results, a novel concept for integrated process for deep desulfurization of liquid hydrocarbons was proposed.

  17. Diesel fuel additive

    SciTech Connect (OSTI)

    Carr, R.P.; Corpuz, M.Y.

    1987-04-28T23:59:59.000Z

    This patent describes an improved cold weather diesel fuel treatment of the type comprising the ingredients % by weight: wax crystal modifier 10 to 50%; sludge dispersant and stabilizer 1 to 10%; hydrocarbon solvent 15 to 40%; oil-soluble water solvent 15 to 40%. The ingredients comprise a low molecular weight organic compound containing from 1 to 3 structural units having formula: -CH/sub 2/CH/sub 2/O-. The improved cold weather diesel fuel treatment is capable of dispersing or dissolving water contained in diesel fuels.

  18. Diesel prices decrease

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel prices continue to increaseDieselDiesel

  19. Diesel prices decrease

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel prices continue toDiesel pricesDiesel

  20. Diesel prices increase

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel prices continueU.S.Diesel pricesDiesel

  1. Diesel prices increase nationally

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel prices continueU.S.DieselDiesel prices

  2. Diesel prices slightly increase

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel pricesDiesel prices slightlyDiesel prices

  3. An Ultra-Low Noise Telecom Wavelength Free Running Single Photon Detector Using Negative Feedback Avalanche Diode

    E-Print Network [OSTI]

    Zhizhong Yan; Deny R. Hamel; Aimee K. Heinrichs; Xudong Jiang; Mark A. Itzler; Thomas Jennewein

    2012-05-31T23:59:59.000Z

    It is challenging to implement genuine free running single photon detectors for the 1550 nm wavelength range with simultaneously high detection efficiency (DE), low dark noise, and good time resolution. We report a novel read out system for the signals from a negative feedback avalanche diode (NFAD) which allows useful operation of these devices at a temperature of 193 K and results in very low dark counts (~100 CPS), good time jitter (~30 ps), and good DE (~10%). We characterized two NFADs with a time correlation method using photons generated from weak coherent pulses (WCP) and photon pairs produced by spontaneous parametric down conversion (SPDC). The inferred detector efficiencies for both types of photon sources agree with each other. The best noise equivalent power of the device is estimated to be 8.1 x 10^(-18) W Hz^(-1/2), more than 10 times better than typical InP/InGaAs SPADs show in free running mode. The afterpulsing probability was found to be less than 0.1% per ns at the optimized operating point. In addition, we studied the performance of an entanglement-based quantum key distribution (QKD) using these detectors and develop a model for the quantum bit error rate (QBER) that incorporates the afterpulsing coefficients. We verified experimentally that using these NFADs it is feasible to implement QKD over 400 km of telecom fibre. Our NFAD photon detector system is very simple, and is well suited for single-photon applications where ultra-low noise and free-running operation is required, and some afterpulsing can be tolerated.

  4. Regional Transit Plan for the Central Texas State Planning Region

    E-Print Network [OSTI]

    Central Texas Regional Transportation Advisory Group

    . The areas HCTD serves are not non-attainment areas, and HCTD wants to be a part of the solution to keep the area as pollution free as possible. HCTD's efforts include: 1. Use of propane or Ultra Low Sulfur Diesel powered buses in its STS service 2. Use... of Ultra Low Sulfur Diesel fuel powered buses in its FRS service 3. Use of ULSD in all the service fleet that uses diesel fuel 4. Coordination of trips to use the Connector service route to minimize the number of vehicles needed for service to medical...

  5. Electrically-Assisted Diesel Particulate Filter Regeneration...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications Substrate Studies of an Electrically-Assisted Diesel Particulate Filter Electrically-Assisted Diesel Particulate Filter Regeneration...

  6. Preserving Diesel Exhaust Ultrafine (Nano-) Particulate Structure...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Preserving Diesel Exhaust Ultrafine (Nano-) Particulate Structure in Genotoxicity Studies to Support Engineering Development of Emission Controls Preserving Diesel Exhaust...

  7. Efficiency Considerations of Diesel Premixed Charge Compression...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency Considerations of Diesel Premixed Charge Compression Ignition Combustion Efficiency Considerations of Diesel Premixed Charge Compression Ignition Combustion Poster...

  8. CLEERS Activities: Diesel Soot Filter Characterization & NOx...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Activities: Diesel Soot Filter Characterization & NOx Control Fundamentals CLEERS Activities: Diesel Soot Filter Characterization & NOx Control Fundamentals 2009 DOE Hydrogen...

  9. [98e]-Catalytic reforming of gasoline and diesel fuel

    SciTech Connect (OSTI)

    Pereira, C.; Wilkenhoener, R.; Ahmed, S.; Krumpelt, M.

    2000-02-29T23:59:59.000Z

    Argonne National Laboratory is developing a fuel processor for converting liquid hydrocarbon fuels to a hydrogen-rich product suitable for a polymer electrolyte fuel cell stack. The processor uses an autothermal reformer to convert the feed to a mixture of hydrogen, carbon dioxide, carbon monoxide and water with trace quantities of other components. The carbon monoxide in the product gas is then converted to carbon dioxide in water-gas shift and preferential oxidation reactors. Fuels that have been tested include standard and low-sulfur gasoline and diesel fuel, and Fischer-Tropsch fuels. Iso-octane and n-hexadecane were also examined as surrogates for gasoline and diesel, respectively. Complete conversion of gasoline was achieved at 750 C in a microreactor over a novel catalyst developed at Argonne. Diesel fuel was completely converted at 850 C over this same catalyst. Product streams contained greater than 60% hydrogen on a dry, nitrogen-free basis with iso-octane, gasoline, and n-hexadecane. For a diesel fuel, product streams contained >50% hydrogen on a dry, nitrogen-free basis. The catalyst activity did not significantly decrease over >16 hours operation with the diesel fuel feed. Coke formation was not observed. The carbon monoxide fraction of the product gas could be reduced to as low as 1% on a dry, nitrogen-free basis when the water-gas shift reactors were used in tandem with the reformer.

  10. Liquid fuel reformer development: Autothermal reforming of Diesel fuel

    SciTech Connect (OSTI)

    Pereira, C.; Bae, J-M.; Ahmed, S.; Krumpelt, M.

    2000-07-24T23:59:59.000Z

    Argonne National Laboratory is developing a process to convert hydrocarbon fuels to clean hydrogen feeds for a polymer electrolyte fuel cell. The process incorporates an autothermal reforming catalyst that can process hydrocarbon feeds at lower temperatures than existing commercial catalysts. The authors have tested the catalyst with three diesel-type fuels: hexadecane, certified low-sulfur grade 1 diesel, and a standard grade 2 diesel. Hexadecane yielded products containing 60% hydrogen on a dry, nitrogen-free basis at 850 C, while maximum hydrogen product yields for the two diesel fuels were near 50%. Residual products in all cases included CO, CO{sub 2}, ethane, and methane. Further studies with grade 1 diesel showed improved conversion as the water:fuel ratio was increased from 1 to 2 at 850 C. Soot formation was reduced when the oxygen:carbon ratio was maintained at 1 at 850 C. There were no significant changes in hydrogen yield as the space velocity and the oxygen:fuel ratio were varied. Tests with a microchannel monolithic catalyst yielded similar or improved hydrogen levels at higher space velocities than with extruded pellets in a packed bed.

  11. Table 16. U.S. No. 2 Diesel Fuel Prices by Sales Type

    U.S. Energy Information Administration (EIA) Indexed Site

    ... 71.1 77.5 78.8 79.6 75.7 66.7 a Includes low-sulfur diesel fuel only. b All end-user sales not included in the other end-user categories shown,...

  12. Optimizing Low Temperature Diesel Combustion

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Diesel Consortium 2008 DOE Merit Review - UW-ERC 1 Optimizing Low Temperature Diesel Combustion Profs. Rolf Reitz, P. Farrell, D. Foster, J. Ghandhi, C. Rutland, S. Sanders Engine...

  13. The Development of a Hydrothermal Method for Slurry Feedstock Preparation for Gasification Technology

    E-Print Network [OSTI]

    He, Wei

    2011-01-01T23:59:59.000Z

    of low sulfur, ultra low sulfur and biodiesel blends in a DIbiofuels produced have ultra-low sulfur levels thanks to thefuels; 5. It contains ultra-low sulfur level and could meet

  14. Remote Sensing of Ammonia and Sulfur Dioxide from On-Road Light

    E-Print Network [OSTI]

    Denver, University of

    ) or directly through adsorbed nitrogen and hydrogen atoms (11, 12). Ammonia emissions from tunnel studies have mea- surements than all other data combined. Sulfur compounds in gasoline combust in the engine to help facilitate the stringent 2007 diesel engine emission requirements. These reductions

  15. Diesel lubrication and cooling systems

    SciTech Connect (OSTI)

    NONE

    1994-12-31T23:59:59.000Z

    The film describes the parts of diesel lubricating and cooling systems and how they work in relation to each other.

  16. Diesel lubrication and cooling systems

    SciTech Connect (OSTI)

    Not Available

    1994-01-01T23:59:59.000Z

    The film describes the parts of diesel lubricating and cooling systems and how they work in relation to each other.

  17. Future Sulfur Dioxide Emissions

    SciTech Connect (OSTI)

    Smith, Steven J.; Pitcher, Hugh M.; Wigley, Tom M.

    2005-12-01T23:59:59.000Z

    The importance of sulfur dioxide emissions for climate change is now established, although substantial uncertainties remain. This paper presents projections for future sulfur dioxide emissions using the MiniCAM integrated assessment model. A new income-based parameterization for future sulfur dioxide emissions controls is developed based on purchasing power parity (PPP) income estimates and historical trends related to the implementation of sulfur emissions limitations. This parameterization is then used to produce sulfur dioxide emissions trajectories for the set of scenarios developed for the Special Report on Emission Scenarios (SRES). We use the SRES methodology to produce harmonized SRES scenarios using the latest version of the MiniCAM model. The implications, and requirements, for IA modeling of sulfur dioxide emissions are discussed. We find that sulfur emissions eventually decline over the next century under a wide set of assumptions. These emission reductions result from a combination of emission controls, the adoption of advanced electric technologies, and a shift away from the direct end use of coal with increasing income levels. Only under a scenario where incomes in developing regions increase slowly do global emission levels remain at close to present levels over the next century. Under a climate policy that limits emissions of carbon dioxide, sulfur dioxide emissions fall in a relatively narrow range. In all cases, the relative climatic effect of sulfur dioxide emissions decreases dramatically to a point where sulfur dioxide is only a minor component of climate forcing by the end of the century. Ecological effects of sulfur dioxide, however, could be significant in some developing regions for many decades to come.

  18. ADVANCED SULFUR CONTROL CONCEPTS

    SciTech Connect (OSTI)

    Apostolos A. Nikolopoulos; Santosh K. Gangwal; William J. McMichael; Jeffrey W. Portzer

    2003-01-01T23:59:59.000Z

    Conventional sulfur removal in integrated gasification combined cycle (IGCC) power plants involves numerous steps: COS (carbonyl sulfide) hydrolysis, amine scrubbing/regeneration, Claus process, and tail-gas treatment. Advanced sulfur removal in IGCC systems involves typically the use of zinc oxide-based sorbents. The sulfides sorbent is regenerated using dilute air to produce a dilute SO{sub 2} (sulfur dioxide) tail gas. Under previous contracts the highly effective first generation Direct Sulfur Recovery Process (DSRP) for catalytic reduction of this SO{sub 2} tail gas to elemental sulfur was developed. This process is currently undergoing field-testing. In this project, advanced concepts were evaluated to reduce the number of unit operations in sulfur removal and recovery. Substantial effort was directed towards developing sorbents that could be directly regenerated to elemental sulfur in an Advanced Hot Gas Process (AHGP). Development of this process has been described in detail in Appendices A-F. RTI began the development of the Single-step Sulfur Recovery Process (SSRP) to eliminate the use of sorbents and multiple reactors in sulfur removal and recovery. This process showed promising preliminary results and thus further process development of AHGP was abandoned in favor of SSRP. The SSRP is a direct Claus process that consists of injecting SO{sub 2} directly into the quenched coal gas from a coal gasifier, and reacting the H{sub 2}S-SO{sub 2} mixture over a selective catalyst to both remove and recover sulfur in a single step. The process is conducted at gasifier pressure and 125 to 160 C. The proposed commercial embodiment of the SSRP involves a liquid phase of molten sulfur with dispersed catalyst in a slurry bubble-column reactor (SBCR).

  19. DIesel Emission Control Technology Developments

    Broader source: Energy.gov (indexed) [DOE]

    (in 2000) Trucks 700,000 Off-road equipment 500,000 Stationary and portable 65,000 Diesel PM Contribution to Risk 70% Diesel PM 3% 2% 3% 4% 8% 10% Diesel Exhaust PM10 (70%) 1,3...

  20. 217 km long distance photon-counting optical time-domain reflectometry based on ultra-low noise up-conversion single photon detector

    E-Print Network [OSTI]

    Guo-Liang Shentu; Qi-Chao Sun; Xiao Jiang; Xiao-Dong Wang; Jason S. Pelc; M. M. Fejer; Qiang Zhang; Jian-Wei Pan

    2013-08-05T23:59:59.000Z

    We demonstrate a photon-counting optical time-domain reflectometry with 42.19 dB dynamic range using an ultra-low noise up-conversion single photon detector. By employing the long wave pump technique and a volume Bragg grating, we reduce the noise of our up-conversion single photon detector, and achieve a noise equivalent power of -139.7 dBm/sqrt(Hz). We perform the OTDR experiments using a fiber of length 216.95 km, and show that our system can identify defects along the entire fiber length with a distance resolution better than 10 cm in a measurement time of 13 minutes.

  1. Ultra low noise YBa{sub 2}Cu{sub 3}O{sub 7??} nano superconducting quantum interference devices implementing nanowires

    SciTech Connect (OSTI)

    Arpaia, R. [Quantum Device Physics Laboratory, Department of Microtechnology and Nanoscience, Chalmers University of Technology, SE-41296 Göteborg (Sweden); CNR-SPIN, Dipartimento di Scienze Fisiche, Università degli Studi di Napoli “Federico II,” I-80125 Napoli (Italy); Arzeo, M.; Nawaz, S.; Charpentier, S.; Lombardi, F.; Bauch, T., E-mail: thilo.bauch@chalmers.se [Quantum Device Physics Laboratory, Department of Microtechnology and Nanoscience, Chalmers University of Technology, SE-41296 Göteborg (Sweden)

    2014-02-17T23:59:59.000Z

    We present results on ultra low noise YBa{sub 2}Cu{sub 3}O{sub 7–?} (YBCO) nano Superconducting QUantum Interference Devices (nanoSQUIDs). To realize such devices, we implemented high quality YBCO nanowires, working as weak links between two electrodes. We observe critical current modulation as a function of an externally applied magnetic field in the full temperature range below the transition temperature T{sub C}. The white flux noise below 1??{sub 0}/?(Hz) at T=8?K makes our nanoSQUIDs very attractive for the detection of small spin systems.

  2. Elemental sulfur recovery process

    DOE Patents [OSTI]

    Flytzani-Stephanopoulos, M.; Zhicheng Hu.

    1993-09-07T23:59:59.000Z

    An improved catalytic reduction process for the direct recovery of elemental sulfur from various SO[sub 2]-containing industrial gas streams. The catalytic process provides combined high activity and selectivity for the reduction of SO[sub 2] to elemental sulfur product with carbon monoxide or other reducing gases. The reaction of sulfur dioxide and reducing gas takes place over certain catalyst formulations based on cerium oxide. The process is a single-stage, catalytic sulfur recovery process in conjunction with regenerators, such as those used in dry, regenerative flue gas desulfurization or other processes, involving direct reduction of the SO[sub 2] in the regenerator off gas stream to elemental sulfur in the presence of a catalyst. 4 figures.

  3. Diesel prices decrease

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel prices continue to increaseDiesel

  4. Diesel prices decrease

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel prices continue toDiesel prices decrease

  5. Diesel prices decrease

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel prices continue toDiesel prices

  6. Diesel prices flat

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel prices continueU.S.Diesel prices flat The

  7. Diesel prices flat nationally

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel prices continueU.S.Diesel prices flat

  8. Diesel prices increase

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel prices continueU.S.Diesel prices

  9. Diesel prices slightly decrease

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel pricesDiesel prices slightly decrease The

  10. Diesel prices slightly decrease

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel pricesDiesel prices slightly decrease

  11. MATERIALS DEGRADATION ANALYSIS AND DEVELOPMENT TO ENABLE ULTRA LOW COST, WEB-PROCESSED WHITE P-OLED FOR SSL

    SciTech Connect (OSTI)

    DR. DEVIN MACKENZIE

    2011-12-13T23:59:59.000Z

    Progress over Phase II of DE-FG02-07ER86293 'Materials Degradation Analysis and Development to Enable Ultra Low Cost, Web-Processed White P-OLED for SSL' was initially rapid in terms of device performance improvements. We exceeded our device luminance lifetime goals for printed flexible white OLEDs as laid out in our project proposal. Our Phase II performance target was to demonstrate >1500 hours luminance lifetime at 100 Cd/m2 from a printed flexible device. We now have R&D devices well in excess of 8000 hrs lifetime at 100 Cd/m2, tested in air. We also were able to produce devices which met the voltage target of >1500 hours below 15V operation. After completing the initial performance milestones, we went on to focus on color-related degradation issues which were cited as important to commercialization of the technology by our manufacturing partners. We also put additional focus on cathode work as the active material development that occurred over the STTR time period required an adaptation of the cathode from the original cathode formulations which were developed based on previous generation active layer materials. We were able to improve compatibility of the cathode with some of the newer generation active layer materials and improve device yield and voltage behavior. An additional objective of the initial Phase II was to further develop the underlying manufacturing technology and real-life product specifications. This is a key requirement that must be met to ensure eventual commercialization of this DOE-funded technology. The link between commercial investment for full commercialization and R&D efforts in OLED solid State Lighting is often a large one. Add-Vision's lower cost, printed OLED manufacturing approach is an attraction, but close engagement with manufacturing partners and addressing customer specifications is a very important link. Manufacturing technology encompasses development of moisture reduction encapsulation technology, improved cost performance, and reductions in operating voltage through thinner and higher uniformity active device layers. We have now installed a pilot encapsulation system at AVI for controlled, high throughput lamination encapsulation of flexible OLEDs in a novel process. Along with this, we have developed, with our materials supply partners, adhesives, barrier films and other encapsulation materials and we are showing total air product lifetimes in the 2-4 years range from a process consistent with our throughput goals of {approx}1M device per month ({approx}30,000 sq. ft. of processed OLEDs). Within the last year of the project, we have been working to introduce the manufacturing improvements made in our LEP deposition and annealing process to our commercial partners. Based on the success of this, a pilot scale-up program was begun. During this process, Add-Vision was acquired by a strategic partner, in no small part, because of the promise of future success of the technology as evidenced by our commercial partners pilot scale-up plans. Overall, the performance, manufacturing and product work in this project has been successful. Additional analysis and device work at LBL has also shown a unique adhesion change with device bias stressing which may result from active layer polymer cross-linking during bias stressing of device. It was shown that even small bias stresses, as a fraction of a full device lifetime stress period, result in measurable chemical change in the device. Further work needs to be conducted to fully understand the chemical nature of this interaction. Elucidation of this effect would enable doped OLED formulation to be engineered to suppress this effect and further extend lifetimes and reduce voltage climb.

  12. Diesel Exhaust Emissions Control for Light-Duty Vehicles

    SciTech Connect (OSTI)

    Mital, R.; Li, J.; Huang, S. C.; Stroia, B. J.; Yu, R. C. (Cummins, Inc.); Anderson, J.A. (Argonne National Laboratory); Howden, Kenneth C. (U.S. Department of Energy)

    2003-03-01T23:59:59.000Z

    The objective of this paper is to present the results of diesel exhaust aftertreatment testing and analysis done under the FreedomCAR program. Nitrogen Oxides (NOx) adsorber technology was selected based on a previous investigation of various NOx aftertreatment technologies including non-thermal plasma, NOx adsorber and active lean NOx. Particulate Matter (PM) emissions were addressed by developing a catalyzed particulate filter. After various iterations of the catalyst formulation, the aftertreatment components were integrated and optimized for a light duty vehicle application. This compact exhaust aftertreatment system is dual leg and consists of a sulfur trap, NOx adsorbers, and catalyzed particulate filters (CPF). During regeneration, supplementary ARCO ECD low-sulfur diesel fuel is injected upstream of the adsorber and CPF in the exhaust. Steady state and transient emission test results with and without the exhaust aftertreatment system (EAS) are presented. Results of soot filter regeneration by injecting low-sulfur diesel fuel and slip of unregulated emissions, such as NH3, are discussed. Effects of adsorber size and bypass strategy on NOx conversion efficiency and fuel economy penalty are also presented in this paper. The results indicate that if the supplementary fuel injection is optimized, NH3 slip is negligible. During the FTP cycle, injection of low sulfur diesel fuel can create temperature exotherms high enough to regenerate a loaded CPF. With the optimized NOx adsorber regeneration strategies the fuel injection penalty can be reduced by 40 to 50%. Results for various other issues like low temperature light off, reductant optimization, exhaust sulfur management, system integration and design trade-off, are also presented and discussed in this paper. (SAE Paper SAE-2003-01-0041 © 2003 SAE International. This paper is published on this website with permission from SAE International. As a user of this website, you are permitted to view this paper on-line, download this pdf file and print one copy of this paper at no cost for your use only. The downloaded pdf file and printout of this SAE paper may not be copied, distributed or forwarded to others or for the use of others.)

  13. Diesel engine fuel systems

    SciTech Connect (OSTI)

    Not Available

    1994-01-01T23:59:59.000Z

    The film shows the basic structure of diesel systems, including the parts and operation of injectors and fuel pumps. It discusses Bosch, General Motors, and Excello Equipment. This title has been declared obsolete for use within the sponsoring agency, but may have content value for educational use.

  14. Diesel engine fuel systems

    SciTech Connect (OSTI)

    NONE

    1994-12-31T23:59:59.000Z

    The film shows the basic structure of diesel systems, including the parts and operation of injectors and fuel pumps. It discusses Bosch, General Motors, and Excello Equipment. This title has been declared obsolete for use within the sponsoring agency, but may have content value for educational use.

  15. Diesel Engine Idling Test

    SciTech Connect (OSTI)

    Larry Zirker; James Francfort; Jordon Fielding

    2006-02-01T23:59:59.000Z

    In support of the Department of Energy’s FreedomCAR and Vehicle Technology Program Office goal to minimize diesel engine idling and reduce the consumption of millions of gallons of diesel fuel consumed during heavy vehicle idling periods, the Idaho National Laboratory (INL) conducted tests to characterize diesel engine wear rates caused by extended periods of idling. INL idled two fleet buses equipped with Detroit Diesel Series 50 engines, each for 1,000 hours. Engine wear metals were characterized from weekly oil analysis samples and destructive filter analyses. Full-flow and the bypass filter cartridges were removed at four stages of the testing and sent to an oil analysis laboratory for destructive analysis to ascertain the metals captured in the filters and to establish wear rate trends. Weekly samples were sent to two independent oil analysis laboratories. Concurrent with the filter analysis, a comprehensive array of other laboratory tests ascertained the condition of the oil, wear particle types, and ferrous particles. Extensive ferrogram testing physically showed the concentration of iron particles and associated debris in the oil. The tests results did not show the dramatic results anticipated but did show wear trends. New West Technologies, LLC, a DOE support company, supplied technical support and data analysis throughout the idle test.

  16. DIESEL FUEL LUBRICATION

    SciTech Connect (OSTI)

    Qu, Jun [ORNL

    2012-01-01T23:59:59.000Z

    The diesel fuel injector and pump systems contain many sliding interfaces that rely for lubrication upon the fuels. The combination of the poor fuel lubricity and extremely tight geometric clearance between the plunger and bore makes the diesel fuel injector vulnerable to scuffing damage that severely limits the engine life. In order to meet the upcoming stricter diesel emission regulations and higher engine efficiency requirements, further fuel refinements that will result in even lower fuel lubricity due to the removal of essential lubricating compounds, more stringent operation conditions, and tighter geometric clearances are needed. These are expected to increase the scuffing and wear vulnerability of the diesel fuel injection and pump systems. In this chapter, two approaches are discussed to address this issue: (1) increasing fuel lubricity by introducing effective lubricity additives or alternative fuels, such as biodiesel, and (2) improving the fuel injector scuffing-resistance by using advanced materials and/or surface engineering processes. The developing status of the fuel modification approach is reviewed to cover topics including fuel lubricity origins, lubricity improvers, alternative fuels, and standard fuel lubricity tests. The discussion of the materials approach is focused on the methodology development for detection of the onset of scuffing and evaluation of the material scuffing characteristics.

  17. Diesel Engine Alternatives

    SciTech Connect (OSTI)

    Ryan, T

    2003-08-24T23:59:59.000Z

    There are basically three different modes of combustion possible for use in reciprocating engines. These include, diffusion burning, as occurs in current diesel engines, flame propagation combustion such as used in conventional SI engines, and homogeneous combustion such as is used in the SwRI HCCI engine. Diesel engines currently offer significant fuel consumption benefits relative to other powerplants for on and off road applications; however, costs and efficiency may become problems as the emissions standards become even more stringent. This presentation presents a discussion of the potentials of HCCI and flame propagation engines as alternatives to the diesel engines. It is suggested that as the emissions standards become more and more stringent, the advantages of the diesel may disappear. The potential for HCCI is limited by the availability of the appropriate fuel. The potential of flame propagation engines is limited by several factors including knock, EGR tolerance, high BMEP operation, and throttling. These limitations are discussed in the context of potential for improvement of the efficiency of the flame propagation engine.

  18. DSRP, direct sulfur production

    SciTech Connect (OSTI)

    McMichael, W.J.; Agarwal, S.K.; Jang, B.L.; Howe, G.B. [Research Triangle Institute, Research Triangle Park, NC (United States); Chen, D.H.; Hopper, J.R. [Lamar Univ., Beaumont, TX (United States)

    1993-06-01T23:59:59.000Z

    The objective of this work is to demonstrate on a bench-scale the Direct Sulfur Recovery Process (DSRP) for up to 99 percent or higher recovery of sulfur (as elemental sulfur) from regeneration off-gases and coal-gas produced in integrated gasification combined cycle (IGCC) power generating systems. Fundamental kinetic and thermodynamic studies will also be conducted to enable development of a model to predict DSRP performance in large-scale reactors and to shed light on the mechanism of DSRP reactions. The ultimate goal of the project is to advance the DSRP technology to the point where industry is willing to support its further development.

  19. Center for Diesel Research Potential Efficiency Improvement

    E-Print Network [OSTI]

    Minnesota, University of

    Center for Diesel Research Potential Efficiency Improvement by Accessory Load Reduction on Hybrid University of Minnesota Center for Diesel Research #12;Center for Diesel Research Acknowledgements · Jeff;Center for Diesel Research Transit Energy Use and Cost · 633 M gallons diesel used for US transit in 2010

  20. (Created 9/04; Revised 10/04, 7/06, 6/07, 8/09,11/11) UNL Environmental Health and Safety (402) 472-4925 http://ehs.unl.edu

    E-Print Network [OSTI]

    Farritor, Shane

    . · Generators are limited to using diesel fuel that contains 0.0015% (15 ppm) or less sulfur (Ultra Low Sulfur to demonstrate compliance with the sulfur limits. #12;(Created 9/04; Revised 10/04, 7/06, 6/07, 8/09,11/11) UNL fuel oil Yes Max gal/12 mo. #2 fuel oil Combined total of 950,000 714,000 Max sulfur #2 fuel oil 0

  1. Sulfur Dioxide Regulations (Ohio)

    Broader source: Energy.gov [DOE]

    This chapter of the law establishes that the Ohio Environmental Protection Agency provides sulfur dioxide emission limits for every county, as well as regulations for the emission, monitoring and...

  2. Systems and methods for controlling diesel engine emissions

    DOE Patents [OSTI]

    Webb, Cynthia Chaffin; Weber, Phillip Anthony; Khair, Magdi K.

    2004-06-01T23:59:59.000Z

    Systems and methods for controlling diesel engine emissions, including, for example, oxides of nitrogen emissions, particulate matter emissions, and the like. The emission control system according to this invention is provided in the exhaust passageway of a diesel engine and includes a catalyst-based particulate filter; and first and second lean NO.sub.x trap systems coupled to the catalyst-based particulate filter. The first and second lean NO.sub.x trap systems are arranged in a parallel flow configuration with each other. Each of the first and second lean NO.sub.x trap systems include a carbon monoxide generating catalyst device, a sulfur trap device, a lean NO.sub.x device, a supplemental fuel injector device, and a plurality of flow diverter devices.

  3. Liquid-Metal Electrode to Enable Ultra-Low Temperature Sodium-Beta Alumina Batteries for Renewable Energy Storage

    SciTech Connect (OSTI)

    Lu, Xiaochuan; Li, Guosheng; Kim, Jin Yong; Mei, Donghai; Lemmon, John P.; Sprenkle, Vincent L.; Liu, Jun

    2014-08-01T23:59:59.000Z

    Metal electrodes have a high capacity for energy storage but have found limited applications in batteries because of dendrite formation and other problems. In this paper, we report a new alloying strategy that can significantly reduce the melting temperature and improve wetting with the electrolyte to allow the use of liquid metal as anode in sodium-beta alumina batteries (NBBs) at much lower temperatures (e.g., 95 to 175°C). Commercial NBBs such as sodium-sulfur (Na-S) battery and sodium-metal halide (ZEBRA) batteries typically operate at relatively high temperatures (e.g., 300-350°C) due to poor wettability of sodium on the surface of ?"-Al2O3. Our combined experimental and computational studies suggest that Na-Cs alloy can replace pure sodium as the anode material, which provides a significant improvement in wettability, particularly at lower temperatures (i.e., <200°C). Single cells with the Na-Cs alloy anode exhibit excellent cycling life over those with pure sodium anode at 175 and 150°C. The cells can even operate at 95°C, which is below the melting temperature of pure sodium. These results demonstrate that NBB can be operated at ultra lower temperatures with successfully solving the wetting issue. This work also suggests a new strategy to use liquid metal as the electrode materials for advanced batteries that can avoid the intrinsic safety issues associated with dendrite formation on the anode.

  4. Diesel exhaust aftertreatment 1996

    SciTech Connect (OSTI)

    NONE

    1996-09-01T23:59:59.000Z

    The papers in this volume deal in the main with the two most common forms of aftertreatment technology. The first is the trap oxidizer, which is a system for trapping and filtering the particulate matter from the exhaust gas and periodically removing it by thermal oxidation. This process is commonly known as regeneration. The second is the diesel oxidation catalyst. Similar in many ways to the flow through a converter in passenger cars, it oxidizes the soluble organic fraction of the diesel exhaust as well as gaseous hydrocarbons and carbon monoxide. This catalyst is being used in production volumes in heavy duty trucks in the US beginning in 1994. Several papers in this volume deal with the development experience of this converter application. There also is included a series of papers by trap and filter manufacturers dealing with improved materials, making their devices more durable. Papers have been processed separately for inclusion on the data base.

  5. Sandia National Laboratories: Diesel Combustion

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Diesel Combustion Caterpillar, Sandia CRADA Opens Door to Multiple Research Projects On April 17, 2013, in Capabilities, Computational Modeling & Simulation, CRF, Materials...

  6. Diesel prices continue to increase

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavid TurnerExperimentalDieselDieselDieselDiesel

  7. Electrically-Assisted Diesel Particulate Filter Regeneration...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Evaluation pm041lance2011p.pdf More Documents & Publications Electrically-Assisted Diesel Particulate Filter Regeneration Substrate Studies of an Electrically-Assisted Diesel...

  8. Optimization of Advanced Diesel Engine Combustion Strategies...

    Broader source: Energy.gov (indexed) [DOE]

    Optimization of Advanced Diesel Engine Combustion Strategies Optimization of Advanced Diesel Engine Combustion Strategies 2010 DOE Vehicle Technologies and Hydrogen Programs Annual...

  9. Vehicle Technologies Office: AVTA - Diesel Internal Combusion...

    Energy Savers [EERE]

    Vehicle Technologies Office: AVTA - Diesel Internal Combusion Engine Vehicles Vehicle Technologies Office: AVTA - Diesel Internal Combusion Engine Vehicles The Advanced Vehicle...

  10. Type-I superconductor pick-up coil in superconducting quantum interference device-based ultra-low field nuclear magnetic resonance

    SciTech Connect (OSTI)

    Hwang, Seong-min, E-mail: smhwang@kriss.re.kr; Kim, Kiwoong; Kyu Yu, Kwon; Lee, Seong-Joo; Hyun Shim, Jeong [Korea Research Institute of Standards and Science, Daejeon 305-340 (Korea, Republic of); Körber, Rainer [Physikalisch-Technische Bundesanstalt (PTB), Abbestraße 2-12, 10587 Berlin (Germany); Magnicon GmbH, Division Berlin, Abbestraße 2-12, D-10587 Berlin (Germany); Burghoff, Martin [Physikalisch-Technische Bundesanstalt (PTB), Abbestraße 2-12, 10587 Berlin (Germany)

    2014-02-10T23:59:59.000Z

    In ultra-low field nuclear magnetic resonance (ULF-NMR) with strong prepolarization field (B{sub p}), type-II superconducting pick-up coils may be vulnerable to flux pinning from the strong B{sub p}. Pick-up coils made of NbTi, Nb, and Pb were evaluated in terms of acquired NMR signal quality. The type-II pick-up coils showed degraded signals above 61?mT maximum exposure, while the Pb pick-up coil exhibited no such degradation. Furthermore, a negative counter pulse following a strong B{sub p} was shown to follow magnetic hysteresis loop to unpin the trapped flux in the type-II pick-up coil and restore the NMR signal.

  11. Search for 2? decays of 96Ru and 104Ru by ultra-low background HPGe gamma spectrometry at LNGS: final results

    E-Print Network [OSTI]

    P. Belli; R. Bernabei; F. Cappella; R. Cerulli; F. A. Danevich; S. d'Angelo; A. Incicchitti; G. P. Kovtun; N. G. Kovtun; M. Laubenstein; D. V. Poda; O. G. Polischuk; A. P. Shcherban; D. A. Solopikhin; J. Suhonen; V. I. Tretyak

    2013-02-28T23:59:59.000Z

    An experiment to search for double beta decay processes in 96Ru and 104Ru, which are accompanied by gamma rays, has been realized in the underground Gran Sasso National Laboratories of the I.N.F.N. (Italy). Ruthenium samples with masses of about (0.5-0.7) kg were measured with the help of ultra-low background high purity Ge gamma ray spectrometry. After 2162 h of data taking the samples were deeply purified to reduce the internal contamination of 40K. The last part of the data has been accumulated over 5479 h. New improved half life limits on 2\\beta+/\\epsilon \\beta+/2\\epsilon\\ processes in 96Ru have been established on the level of 10^{20} yr, in particular for decays to the ground state of 96Mo: T1/2(2\

  12. Limits on Low-Mass WIMP Dark Matter with an Ultra-Low-Energy Germanium Detector at 220 eV Threshold

    E-Print Network [OSTI]

    Shin-Ted Lin; H. T. Wong; for the TEXONO Collaboration

    2008-10-20T23:59:59.000Z

    An energy threshold of (220$\\pm$10) eV was achieved at an efficiency of 50% with a four-channel ultra-low-energy germanium detector each with an active mass of 5 g\\cite{wimppaper}. This provides a unique probe to WIMP dark matter with mass below 10 GeV. With low background data taken at the Kuo-Sheng Laboratory, constraints on WIMPs in the galactic halo were derived. Both spin-independent WIMP-nucleon and spin-dependent WIMP-neutron bounds improve over previous results for WIMP mass between 3$-$6 GeV. These results, together with those on spin-dependent couplings, will be presented. Sensitivities for full-scale experiments were projected. This detector technique makes the unexplored sub-keV energy window accessible for new neutrino and dark matter experiments.

  13. Search for 2\\beta\\ decays of 96Ru and 104Ru by ultra-low background HPGe gamma spectrometry at LNGS: final results

    E-Print Network [OSTI]

    Belli, P; Cappella, F; Cerulli, R; Danevich, F A; d'Angelo, S; Incicchitti, A; Kovtun, G P; Kovtun, N G; Laubenstein, M; Poda, D V; Polischuk, O G; Shcherban, A P; Solopikhin, D A; Suhonen, J; Tretyak, V I

    2013-01-01T23:59:59.000Z

    An experiment to search for double beta decay processes in 96Ru and 104Ru, which are accompanied by gamma rays, has been realized in the underground Gran Sasso National Laboratories of the I.N.F.N. (Italy). Ruthenium samples with masses of about (0.5-0.7) kg were measured with the help of ultra-low background high purity Ge gamma ray spectrometry. After 2162 h of data taking the samples were deeply purified to reduce the internal contamination of 40K. The last part of the data has been accumulated over 5479 h. New improved half life limits on 2\\beta+/\\epsilon \\beta+/2\\epsilon\\ processes in 96Ru have been established on the level of 10^{20} yr, in particular for decays to the ground state of 96Mo: T1/2(2\

  14. Diesel fuel aromatic and cetane number effects on combustion and emissions from a prototype 1991 diesel engine

    SciTech Connect (OSTI)

    Sienicki, E.J.; Jass, R.E.; Slodowske, W.J.; McCarthy, C.I.; Krodel, A.L.

    1990-01-01T23:59:59.000Z

    This book reports on a prototype 1991-model diesel engine that was tested using EPA transient emissions procedures to determine the effect of fuel properties on combustion characteristics and exhaust emissions. The eleven test fuel set focused primarily on total aromatic content, multi-ring aromatic content, and cetane number, but other fuel variables were also studied. Hydrotreating was used to obtain reductions in fuel sulfur and aromatic content. Increasing cetane number and reducing aromatic content resulted in lower emissions of hydrocarbons and NO{sub x}. Particulate emission were best predicted by sulfur content, aromatic content and 90% distillation temperature. Multi-ring aromatics showed a greater significance that total aromatics on hydrocarbon and particulate emissions. combustion parameters were highly dependent on fuel cetane number.

  15. Catalyst for the reduction of sulfur dioxide to elemental sulfur

    DOE Patents [OSTI]

    Jin, Yun (Peking, CN); Yu, Qiquan (Peking, CN); Chang, Shih-Ger (El Cerrito, CA)

    1996-01-01T23:59:59.000Z

    The inventive catalysts allow for the reduction of sulfur dioxide to elemental sulfur in smokestack scrubber environments. The catalysts have a very high sulfur yield of over 90% and space velocity of 10,000 h.sup.-1. They also have the capacity to convert waste gases generated during the initial conversion into elemental sulfur. The catalysts have inexpensive components, and are inexpensive to produce. The net impact of the invention is to make this technology practically available to industrial applications.

  16. Impact of Fuel Metal Impurities on the Durability of a Light-Duty Diesel Aftertreatment System

    SciTech Connect (OSTI)

    Williams, A.; Burton, J.; McCormick, R. L.; Toops, T.; Wereszczak, A. A.; Fox, E. E.; Lance, M. J.; Cavataio, G.; Dobson, D.; Warner, J.; Brezny, R.; Nguyen, K.; Brookshear, D. W.

    2013-04-01T23:59:59.000Z

    Alkali and alkaline earth metal impurities found in diesel fuels are potential poisons for diesel exhaust catalysts. A set of diesel engine production exhaust systems was aged to 150,000 miles. These exhaust systems included a diesel oxidation catalyst, selective catalytic reduction (SCR) catalyst, and diesel particulate filter (DPF). Four separate exhaust systems were aged, each with a different fuel: ultralow sulfur diesel containing no measureable metals, B20 (a common biodiesel blend) containing sodium, B20 containing potassium, and B20 containing calcium, which were selected to simulate the maximum allowable levels in B100 according to ASTM D6751. Analysis included Federal Test Procedure emissions testing, bench-flow reactor testing of catalyst cores, electron probe microanalysis (EPMA), and measurement of thermo-mechanical properties of the DPFs. EPMA imaging found that the sodium and potassium penetrated into the washcoat, while calcium remained on the surface. Bench-flow reactor experiments were used to measure the standard nitrogen oxide (NOx) conversion, ammonia storage, and ammonia oxidation for each of the aged SCR catalysts. Vehicle emissions tests were conducted with each of the aged catalyst systems using a chassis dynamometer. The vehicle successfully passed the 0.2 gram/mile NOx emission standard with each of the four aged exhaust systems.

  17. Reformulated diesel fuel and method

    DOE Patents [OSTI]

    McAdams, Hiramie T [Carrollton, IL; Crawford, Robert W [Tucson, AZ; Hadder, Gerald R [Oak Ridge, TN; McNutt, Barry D [Arlington, VA

    2006-08-22T23:59:59.000Z

    A method for mathematically identifying at least one diesel fuel suitable for combustion in an automotive diesel engine with significantly reduced emissions and producible from known petroleum blendstocks using known refining processes, including the use of cetane additives (ignition improvers) and oxygenated compounds.

  18. "Performance, Emission and Particle distribution of Diesel Engines Fueled with Diesel-Dimethoxymethane (DMM) Blends"

    E-Print Network [OSTI]

    Xibin Wang "Performance, Emission and Particle distribution of Diesel Engines Fueled with Diesel-Dimethoxymethane (DMM) Blends" Abstract : Combustion, performance and emission were studied for DI diesel engine fuelled with DMM/diesel fuel blends for DMM content from 0 to 50%. Results showed that, for diesel engine with fuel

  19. Diesel prices decrease

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel prices continue to

  20. diesel.vp

    Gasoline and Diesel Fuel Update (EIA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 111 1,613 122 40 Buildingto17 34 44Year199873.4 66.1 56.2 50.4415 683 460. 58071Diesel Fuel Price

  1. Technical Challenges and Opportunities Light-Duty Diesel Engines...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Challenges and Opportunities Light-Duty Diesel Engines in North America Technical Challenges and Opportunities Light-Duty Diesel Engines in North America 2005 Diesel Engine...

  2. Glow Plug Integrated Piezo-Ceramic Combustion Sensor for Diesel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Glow Plug Integrated Piezo-Ceramic Combustion Sensor for Diesel Engines Glow Plug Integrated Piezo-Ceramic Combustion Sensor for Diesel Engines 2005 Diesel Engine Emissions...

  3. Technology Development for Light Duty High Efficient Diesel Engines...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Light Duty High Efficient Diesel Engines Technology Development for Light Duty High Efficient Diesel Engines Improve the efficiency of diesel engines for light duty applications...

  4. adicionado ao diesel: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    with diesel. Main focus of this research is to investigate the performance of diesel engine by injecting hydrogen peroxide as blends with diesel at 2%, 5% and 10 %...

  5. automotive diesel exhaust: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    with diesel. Main focus of this research is to investigate the performance of diesel engine by injecting hydrogen peroxide as blends with diesel at 2%, 5% and 10 %...

  6. advanced automotive diesel: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    with diesel. Main focus of this research is to investigate the performance of diesel engine by injecting hydrogen peroxide as blends with diesel at 2%, 5% and 10 %...

  7. agricultural diesel engine: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    with diesel. Main focus of this research is to investigate the performance of diesel engine by injecting hydrogen peroxide as blends with diesel at 2%, 5% and 10 %...

  8. adiabatic diesel engine: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    with diesel. Main focus of this research is to investigate the performance of diesel engine by injecting hydrogen peroxide as blends with diesel at 2%, 5% and 10 %...

  9. advanced diesel engine: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    with diesel. Main focus of this research is to investigate the performance of diesel engine by injecting hydrogen peroxide as blends with diesel at 2%, 5% and 10 %...

  10. auxiliary diesel units: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    with diesel. Main focus of this research is to investigate the performance of diesel engine by injecting hydrogen peroxide as blends with diesel at 2%, 5% and 10 %...

  11. adiabatic diesel engines: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    with diesel. Main focus of this research is to investigate the performance of diesel engine by injecting hydrogen peroxide as blends with diesel at 2%, 5% and 10 %...

  12. advanced diesel engines: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    with diesel. Main focus of this research is to investigate the performance of diesel engine by injecting hydrogen peroxide as blends with diesel at 2%, 5% and 10 %...

  13. Effects of an Accelerated Diesel Engine Replacement/Retrofit Program

    E-Print Network [OSTI]

    Millstein, Dev E.; Harley, Robert A

    2009-01-01T23:59:59.000Z

    Heavy-Duty Diesel Truck Emissions. Environ. Sci. Technol. ,reductions in diesel truck emissions are forecast to occurof NO 2 /NO x emissions from diesel trucks equipped with

  14. Optimization of an Advanced Passive/Active Diesel Emission Control...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    & Publications Diesel Particulate Filters and NO2 Emission Limits Active Diesel Emission Control Technology for Transport Refrigeration Units Active Diesel Emission Control Systems...

  15. EPA Clean Diesel Funding Assistance Program | Department of Energy

    Energy Savers [EERE]

    for projects to achieve significant reductions in diesel emissions in terms of tons of pollution produced by diesel engines and diesel emissions exposure, particularly from...

  16. Effects of an Accelerated Diesel Engine Replacement/Retrofit Program

    E-Print Network [OSTI]

    Millstein, Dev E.; Harley, Robert A

    2009-01-01T23:59:59.000Z

    and Cackette, T. A. , (2001). Diesel engines: environmentalfrom On-Road Gasoline and Diesel Vehicles. Atmos. Environ.emissions from gasoline- and diesel-powered motor vehicles.

  17. Value Analysis of Alternative Diesel Particulate Filter (DPF...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Value Analysis of Alternative Diesel Particulate Filter (DPF) Substrates for Future Diesel Aftertreatment Systems Value Analysis of Alternative Diesel Particulate Filter (DPF)...

  18. Future Diesel Engine Thermal Efficiency Improvement andn Emissions...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Diesel Engine Thermal Efficiency Improvement andn Emissions Control Technology Future Diesel Engine Thermal Efficiency Improvement andn Emissions Control Technology 2005 Diesel...

  19. Retrofit Diesel Emissions Control System Providing 50% NOxControl...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Diesel Emissions Control System Providing 50% NOxControl Retrofit Diesel Emissions Control System Providing 50% NOxControl 2005 Diesel Engine Emissions Reduction (DEER) Conference...

  20. Perspectives Regarding Diesel Engine Emissions Reduction in the...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Perspectives Regarding Diesel Engine Emissions Reduction in the Northeast Perspectives Regarding Diesel Engine Emissions Reduction in the Northeast 2004 Diesel Engine Emissions...

  1. Regulated Emissions from Diesel and Compressed Natural Gas Transit...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Emissions from Diesel and Compressed Natural Gas Transit Buses Regulated Emissions from Diesel and Compressed Natural Gas Transit Buses Poster presentaiton at the 2007 Diesel...

  2. Carbonyl Emissions from Gasoline and Diesel Motor Vehicles

    E-Print Network [OSTI]

    Jakober, Chris A.

    2008-01-01T23:59:59.000Z

    emissions from gasoline and diesel motor vehicles. Environ.of four dilutions of diesel engine exhaust for a subchronicautomobiles and heavy-duty diesel trucks. Environ. Sci.

  3. Alloy Foam Diesel Emissions Control School Bus Implementation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Alloy Foam Diesel Emissions Control School Bus Implementation Alloy Foam Diesel Emissions Control School Bus Implementation Poster presentation from the 2007 Diesel...

  4. Measurements of Diesel Truck Traffic Associated with Goods Movement

    E-Print Network [OSTI]

    Houston, Douglas; Krudysz, Margaret; Winer, Arthur

    2007-01-01T23:59:59.000Z

    Concentrations of PM2.5 and Diesel Exhaust Particles onPatterns of Measured Port Diesel Traffic. (a) Intersectionof particulate emissions from diesel engines: a review’, J.

  5. The 60% Efficient Diesel Engine: Probably, Possible, Or Just...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    The 60% Efficient Diesel Engine: Probably, Possible, Or Just a Fantasy? The 60% Efficient Diesel Engine: Probably, Possible, Or Just a Fantasy? 2005 Diesel Engine Emissions...

  6. Requirements-Driven Diesel Catalyzed Particulate Trap Design...

    Broader source: Energy.gov (indexed) [DOE]

    Requirements-Driven Diesel Catalyzed Particulate Trap Design and Optimization Requirements-Driven Diesel Catalyzed Particulate Trap Design and Optimization 2005 Diesel Engine...

  7. Nanomaterials: Organic and Inorganic for Next-Generation Diesel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Nanomaterials: Organic and Inorganic for Next-Generation Diesel Technologies Nanomaterials: Organic and Inorganic for Next-Generation Diesel Technologies 2007 Diesel...

  8. Diesel fuel to dc power: Navy & Marine Corps Applications

    SciTech Connect (OSTI)

    Bloomfield, D.P. [Analytic Power Corp., Boston, MA (United States)

    1996-12-31T23:59:59.000Z

    During the past year Analytic Power has tested fuel cell stacks and diesel fuel processors for US Navy and Marine Corps applications. The units are 10 kW demonstration power plants. The USN power plant was built to demonstrate the feasibility of diesel fueled PEM fuel cell power plants for 250 kW and 2.5 MW shipboard power systems. We designed and tested a ten cell, 1 kW USMC substack and fuel processor. The complete 10 kW prototype power plant, which has application to both power and hydrogen generation, is now under construction. The USN and USMC fuel cell stacks have been tested on both actual and simulated reformate. Analytic Power has accumulated operating experience with autothermal reforming based fuel processors operating on sulfur bearing diesel fuel, jet fuel, propane and natural gas. We have also completed the design and fabrication of an advanced regenerative ATR for the USMC. One of the significant problems with small fuel processors is heat loss which limits its ability to operate with the high steam to carbon ratios required for coke free high efficiency operation. The new USMC unit specifically addresses these heat transfer issues. The advances in the mill programs have been incorporated into Analytic Power`s commercial units which are now under test.

  9. Diesel prices continue to decrease

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavid TurnerExperimentalDiesel pricesDieselDiesel

  10. Diesel prices continue to increase

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavid TurnerExperimentalDieselDiesel pricesDiesel

  11. Diesel prices continue to increase

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavid TurnerExperimentalDieselDieselDiesel prices

  12. Diesel prices continue to increase

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavid TurnerExperimentalDieselDieselDiesel

  13. Diesel prices remain fairly stable

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel prices continueU.S.DieselDiesel

  14. Diesel prices slightly increase nationally

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel pricesDiesel prices slightlyDiesel

  15. Integrated production/use of ultra low-ash coal, premium liquids and clean char. Final technical report, September 1, 1991--August 31, 1992

    SciTech Connect (OSTI)

    Kruse, C.W.; Carlson, S.L. [Illinois State Geological Survey, Champaign, IL (United States); Snoeyink, V.L.; Feizoulof, C.; Assanis; Syrimis, M. [Illinois Univ., Urbana (United States); Fatemi, S.M. [Amoco, Naperville, IL (United States)

    1992-12-31T23:59:59.000Z

    The objective of this research is to invert the conventional scale of values for products of coal utilization processes by making coal chars (carbons) that, because of their unique properties, are the most valuable materials in the product slate. A unique type of coal-derived carbon studied in this project is oxidized activated coal char having both adsorptive and catalyst properties. Major program elements were (a) preparation and characterization of materials (b) characterization of carbons and catalyst testing (c) completion of diesel engine testing of low-ash coal and (d) initiation of a two-year adsorption study. Materials prepared were (a) two low-ash coal samples one via ChemCoal processing of IBC-109 and the other by acid dissolution of IBC-109`s mineral matter, (b) coal char (MG char), (c) activated low-ash carbon (AC), (d) oxidized activated carbon (OAC). Amoco continued its support with state-of-the art analytical capabilities and development of catalyst testing procedures. Diesel engine tests were made with low ash coal dispersed in diesel fuel at solid loadings of 20% and 35%. The slurry was successfully burned in cylinder 2 of a two-cylinder diesel engine, after modifications of the engine`s fuel injection system. The higher speed proved to be more favorable but the slurry burned with a slightly improved thermal and combustion efficiency at both speeds with respect to diesel fuel alone. Adsorption studies included preparation of seven base-line carbon samples and their characterization, including their N{sub 2} BET surface areas and apparent densities. Paranitrophenol (PNP) adsorption isotherms were determined for the six controls. Oxidation of carbon with nitric acid decreases activated carbon`s PNP adsorption capacity while air oxidation increases adsorption capacity.

  16. REVIEW OF DIESEL PARTICULATE MATTER SAMPLING METHODS Supplemental Report # 1

    E-Print Network [OSTI]

    Minnesota, University of

    REVIEW OF DIESEL PARTICULATE MATTER SAMPLING METHODS Supplemental Report # 1 DIESEL EXHAUST.D. and Megan Arnold University of Minnesota Department of Mechanical Engineering Center for Diesel Research....................................................................................... 3 Diesel aerosol size instrumentation............................................................ 4

  17. Development of an ultra-safe, ultra-low-emissions natural gas-fueled school bus: Phase 2, prototype hardware development

    SciTech Connect (OSTI)

    Kubesh, J. [Southwest Research Inst., San Antonio, TX (United States)

    1996-04-01T23:59:59.000Z

    This report summarizes work done on Phase 2, ``Prototype Hardware Development`` of Southwest Research Institute (SwRI) Project No. 03-6871, ``Development of an Ultra-Safe, Ultra-Low-Emissions Alternative-Fueled School Bus``. A prototype school bus was designed and constructed. This bus incorporated many new technologies to increase the safety of the bus passengers as well as pedestrians boarding and leaving the bus. These technologies emphasized increased visibility between the bus driver and pedestrians or vehicles, and included the use of high intensity discharge lighting, pedestrian and vehicle detection systems, and remote-mounted cameras. Passenger safety was also stressed, with the application of seat belts and improved emergency exits and lighting. A natural gas-fueled engine was developed for powering the bus. The development process focused primarily on improvements to the lean operation of the engine and control system advancements. The control system development included investigations into alternative control algorithms for steady-state and transient operation, various fuel metering devices, as well as new methods for wastegate control, knock and misfire detection, and catalyst monitoring. Both the vehicle and engine systems represent state-of-the-art technologies. Integration of the vehicle and engine is planned for the next phase of the project, followed by a demonstration test of the overall vehicle system.

  18. Ultra-low emittance beam generation using two-color ionization injection in a CO2 laser-driven plasma accelerator

    E-Print Network [OSTI]

    Schroeder, C B; Bulanov, S S; Chen, M; Esarey, E; Geddes, C G R; Vay, J -L; Yu, L -L; Leemans, W P

    2015-01-01T23:59:59.000Z

    Ultra-low emittance (tens of nm) beams can be generated in a plasma accelerator using ionization injection of electrons into a wakefield. An all-optical method of beam generation uses two laser pulses of different colors. A long-wavelength drive laser pulse (with a large ponderomotive force and small peak electric field) is used to excite a large wakefield without fully ionizing a gas, and a short-wavelength injection laser pulse (with a small ponderomotive force and large peak electric field), co-propagating and delayed with respect to the pump laser, to ionize a fraction of the remaining bound electrons at a trapped wake phase, generating an electron beam that is accelerated in the wake. The trapping condition, the ionized electron distribution, and the trapped bunch dynamics are discussed. Expressions for the beam transverse emittance, parallel and orthogonal to the ionization laser polarization, are presented. An example is shown using a 10-micron CO2 laser to drive the wake and a frequency-doubled Ti:Al2...

  19. Orbital effects of a monochromatic plane gravitational wave with ultra-low frequency incident on a gravitationally bound two-body system

    E-Print Network [OSTI]

    Lorenzo Iorio

    2014-09-12T23:59:59.000Z

    We analytically compute the long-term orbital variations of a test particle orbiting a central body acted upon by an incident monochromatic plane gravitational wave. We assume that the characteristic size of the perturbed two-body system is much smaller than the wavelength of the wave. Moreover, we also suppose that the wave's frequency is much smaller than the particle's orbital one. We make neither a priori assumptions about the direction of the wavevector nor on the orbital geometry of the planet. We find that, while the semi-major axis is left unaffected, the eccentricity, the inclination, the longitude of the ascending node, the longitude of pericenter and the mean anomaly undergo non-vanishing long-term changes. They are not secular trends because of the slow modulation introduced by the tidal matrix coefficients and by the orbital elements themselves. They could be useful to indepenedently constrain the ultra-low frequency waves which may have been indirectly detected in the BICEP2 experiment. Our calculation holds, in general, for any gravitationally bound two-body system whose characteristic frequency is much larger than the frequency of the external wave. It is also valid for a generic perturbation of tidal type with constant coefficients over timescales of the order of the orbital period of the perturbed particle.

  20. PARTICULATE CHARACTERIZATION AND ULTRA LOW-NOx BURNER FOR THE CONTROL OF NO{sub x} AND PM{sub 2.5} FOR COAL FIRED BOILERS

    SciTech Connect (OSTI)

    Ralph Bailey; Hamid Sarv; Jim Warchol; Debi Yurchison

    2001-09-30T23:59:59.000Z

    In response to the serious challenge facing coal-fired electric utilities with regards to curbing their NO{sub x} and fine particulate emissions, Babcock and Wilcox and McDermott Technology, Inc. conducted a project entitled, ''Particulate Characterization and Ultra Low-NO{sub x} Burner for the Control of NO{sub x} and PM{sub 2.5} for Coal Fired Boilers.'' The project included pilot-scale demonstration and characterization of technologies for removal of NO{sub x} and primary PM{sub 2.5} emissions. Burner development and PM{sub 2.5} characterization efforts were based on utilizing innovative concepts in combination with sound scientific and fundamental engineering principles and a state-of-the-art test facility. Approximately 1540 metric tonnes (1700 tons) of high-volatile Ohio bituminous coal were fired. Particulate sampling for PM{sub 2.5} emissions characterization was conducted in conjunction with burner testing. Based on modeling recommendations, a prototype ultra low-NO{sub x} burner was fabricated and tested at 100 million Btu/hr in the Babcock and Wilcox Clean Environment Development Facility. Firing the unstaged burner with a high-volatile bituminous Pittsburgh 8 coal at 100 million Btu/hr and 17% excess air achieved a NO{sub x} goal of 0.20 lb NO{sub 2}/million Btu with a fly ash loss on ignition (LOI) of 3.19% and burner pressure drop of 4.7 in H{sub 2}O for staged combustion. With the burner stoichiometry set at 0.88 and the overall combustion stoichiometry at 1.17, average NO{sub x} and LOI values were 0.14 lb NO{sub 2}/million Btu and 4.64% respectively. The burner was also tested with a high-volatile Mahoning 7 coal. Based on the results of this work, commercial demonstration is being pursued. Size classified fly ash samples representative of commercial low-NO{sub x} and ultra low-NO{sub x} combustion of Pittsburgh 8 coal were collected at the inlet and outlet of an ESP. The mass of size classified fly ash at the ESP outlet was sufficient to evaluate the particle size distribution, but was of insufficient size to permit reliable chemical analysis. The size classified fly ash from the inlet of the ESP was used for detailed chemical analyses. Chemical analyses of the fly ash samples from the ESP outlet using a high volume sampler were performed for comparison to the size classified results at the inlet. For all test conditions the particulate removal efficiency of the ESP exceeded 99.3% and emissions were less than the NSPS limits of {approx}48 mg/dscm. With constant combustion conditions, the removal efficiency of the ESP increased as the ESP voltage and Specific Collection Area (SCA) increased. The associated decrease in particle emissions occurred in size fractions both larger and smaller than 2.5 microns. For constant ESP voltage and SCA, the removal efficiency for the ultra low-NO{sub x} combustion ash (99.4-99.6%) was only slightly less than for the low-NO{sub x} combustion ash (99.7%). The decrease in removal efficiency was accompanied by a decrease in ESP current. The emission of PM{sub 2.5} from the ESP did not change significantly as a result of the change in combustion conditions. Most of the increase in emissions was in the size fraction greater than 2.5 microns, indicating particle re-entrainment. These results may be specific to the coal tested in this program. In general, the concentration of inorganic elements and trace species in the fly ash at the ESP inlet was dependent on the particle size fraction. The smallest particles tended to have higher concentrations of inorganic elements/trace species than larger particles. The concentration of most elements by particle size range was independent of combustion condition and the concentration of soluble ions in the fly ash showed little change with combustion condition when evaluated on a carbon free basis.

  1. Advanced Boost System Development for Diesel HCCI/LTC Application...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications Advanced Boost System Development for Diesel HCCILTC Application Advanced Boost System Development for Diesel HCCILTC Application...

  2. Simultaneous Efficiency, NOx, and Smoke Improvements through Diesel/Gasoline Dual-Fuel Operation in a Diesel Engine 

    E-Print Network [OSTI]

    Sun, Jiafeng

    2014-08-05T23:59:59.000Z

    Diesel/gasoline dual-fuel combustion uses both gasoline and diesel fuel in diesel engines to exploit their different reactivities. This operation combines the advantages of diesel fuel and gasoline while avoiding their disadvantages, attains...

  3. Catalyst for the reduction of sulfur dioxide to elemental sulfur

    DOE Patents [OSTI]

    Jin, Y.; Yu, Q.; Chang, S.G.

    1996-02-27T23:59:59.000Z

    The inventive catalysts allow for the reduction of sulfur dioxide to elemental sulfur in smokestack scrubber environments. The catalysts have a very high sulfur yield of over 90% and space velocity of 10,000 h{sup {minus}1}. They also have the capacity to convert waste gases generated during the initial conversion into elemental sulfur. The catalysts have inexpensive components, and are inexpensive to produce. The net impact of the invention is to make this technology practically available to industrial applications. 21 figs.

  4. BIODIESEL AS AN ALTERNATE FUEL FOR POLLUTION CONTROL IN DIESEL ENGINE

    E-Print Network [OSTI]

    Mr. Paresh K. Kasundra; Prof Ashish; V. Gohil

    Diesel vehicles are the major source for air pollution; there is great potential for global warming due to discharge of greenhouse gases like CO2 from vehicles. Many lung problems are connected with particulate matter emitted by diesel vehicle including dust, soot and smoke. People are exposed to pollution even as they talk or when stir up the dust when they walk. Biodiesel is a non-toxic, biodegradable and renewable fuel. Compared to diesel fuel, biodiesel produces no sulfur, no net carbon dioxide, less carbon monoxide and more oxygen. More free oxygen leads to the complete combustion and reduced emission. Overall biodiesel emissions are very less compared to diesel fuel emissions which is promising pollution free environment. Abundant source of vegetable oil in India and its ease of conversion to biodiesel help to save large expenditure done on import of petroleum products and economic growth of country. Biodiesel also generates huge rural employment and degraded lands can be restored due to plantation of oil plants which help in reducing pollution. Extensive research is going on in different countries on different types of vegetable oils like sunflower oil, karanj oil, linseed oil, soya been oil, palm oil, and many more, which can be used in those countries as per availability, our research is in progress on CNSL and its blend with diesel, research is going on in right direction and likely to get surprising

  5. Growing Together Columbia University's

    E-Print Network [OSTI]

    Yang, Junfeng

    . In addition, all construction equipment use air pollution control devices and Ultra-Low Sulfur Diesel (ULSD will revitalize the four former industrial blocks from 125th/129th to 133rd Street between Broadway and 12th. What to Expect Although contractors carefully stage construction activities to minimize disruption

  6. GTM RESEARCH DECEMBER 2009 COPYRIGHT 2009, GREENTECH MEDIA INC. ALL RIGHTS RESERVED

    E-Print Network [OSTI]

    Infrastructure Tax Credit 85 3.5.1.5 Ultra-low Sulfur Diesel (ULSD) 85 3.5.2 U.S Biodiesel Market Overview 85 3.5.3 Import Duty on Fuel Ethanol 37 2.5.4 California's Air Resource Board "Low Carbon Fuel Standard" 37 2

  7. Port Authority of Allegheny County: Green Facts Hybrid Buses

    E-Print Network [OSTI]

    Sibille, Etienne

    began using ultra-low sulfur diesel (ULSD) on select buses in April 2005, and went system-wide with ULSD in batteries when the vehicle is de-accelerating and at times of low engine load. This energy is used

  8. Performance Characterization of a Medium-Duty Diesel Engine with Bio-Diesel and Petroleum Diesel Fuels 

    E-Print Network [OSTI]

    Esquivel, Jason

    2010-01-16T23:59:59.000Z

    characterizes the performance of a medium-duty diesel engine fuelled with biodiesel and conventional diesel. The objective is accomplished by taking measurements of manifold pressure and temperature, fuel flow, air flow, and torque. The study first characterizes...

  9. Method of removing and recovering elemental sulfur from highly reducing gas streams containing sulfur gases

    DOE Patents [OSTI]

    Gangwal, Santosh K.; Nikolopoulos, Apostolos A.; Dorchak, Thomas P.; Dorchak, Mary Anne

    2005-11-08T23:59:59.000Z

    A method is provided for removal of sulfur gases and recovery of elemental sulfur from sulfur gas containing supply streams, such as syngas or coal gas, by contacting the supply stream with a catalyst, that is either an activated carbon or an oxide based catalyst, and an oxidant, such as sulfur dioxide, in a reaction medium such as molten sulfur, to convert the sulfur gases in the supply stream to elemental sulfur, and recovering the elemental sulfur by separation from the reaction medium.

  10. A NOVEL VAPOR-PHASE PROCESS FOR DEEP DESULFURIZATION OF NAPHTHA/DIESEL

    SciTech Connect (OSTI)

    B.S. Turk; R.P. Gupta; S.K. Gangwal

    2003-06-30T23:59:59.000Z

    Tier 2 regulations issued by the U.S. Environmental Protection Agency (EPA) require a substantial reduction in the sulfur content of gasoline. Similar regulations have been enacted for the sulfur level in on-road diesel and recently off-road diesel. The removal of this sulfur with existing and installed technology faces technical and economic challenges. These challenges created the opportunity for new emerging technologies. Research Triangle Institute (RTI) with subcontract support from Kellogg Brown & Root, Inc., (KBR) used this opportunity to develop RTI's transport reactor naphtha desulfurization (TReND) process. Starting with a simple conceptual process design and some laboratory results that showed promise, RTI initiated an accelerated research program for sorbent development, process development, and marketing and commercialization. Sorbent development has resulted in the identification of an active and attrition resistant sorbent that has been prepared in commercial equipment in 100 lb batches. Process development has demonstrated both the sulfur removal performance and regeneration potential of this sorbent. Process development has scaled up testing from small laboratory to pilot plant transport reactor testing. Testing in the transport reactor pilot plant has demonstrated the attrition resistance, selective sulfur removal activity, and regeneration activity of this sorbent material. Marketing and commercialization activities have shown with the existing information that the process has significant capital and operating cost benefits over existing and other emerging technologies. The market assessment and analysis provided valuable feedback about the testing and performance requirements for the technical development program. This market analysis also provided a list of potential candidates for hosting a demonstration unit. Although the narrow window of opportunity generated by the new sulfur regulations and the conservative nature of the refining industry slowed progress of the demonstration unit, negotiations with potential partners are proceeding for commercialization of this process.

  11. DIESEL/HEAVY The diesel/heavy equipment certificate offers training in maintenance

    E-Print Network [OSTI]

    Ickert-Bond, Steffi

    DIESEL/HEAVY EQUIPMENT The diesel/heavy equipment certificate offers training in maintenance and repair of heavy equipment and trucks. Students will learn to work on electrical and air systems, diesel · Small Engines · Automotive Maintenance · Welding · Training for entry level heavy diesel equipment

  12. On-Board Diesel & Hybrid Diesel-Electric Transit Bus PM

    E-Print Network [OSTI]

    Holmén, Britt A.

    On-Board Diesel & Hybrid Diesel-Electric Transit Bus PM Mass and Size-Resolved Number Emissions AND cost-effective ­ 2003 -- Purchase 2 hybrid diesel-electric buses ­ Emissions Testing ­ gases Particulate Mass -- filter #12;Motivation · Ultrafine (UF) particle health effects · Diesel vehicle exhaust

  13. BMW Diesel - Engine Concepts for Efficient Dynamics

    Broader source: Energy.gov (indexed) [DOE]

    "24 Hours of Nrburgring" 2001 - 2nd Gen. Common Rail (1600 bar) 2004 - Variable Twin Turbo - Diesel Particulate Filter of 2nd Gen. 1999 - First V8 Diesel Sedan in Premium...

  14. Advanced Technology Light Duty Diesel Aftertreatment System ...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Approach to Low Temperature NOx Emission Abatement Cummins' Next Generation Tier 2, Bin 2 Light Truck Diesel Engine ATP-LD; Cummins Next Generation Tier 2 Bin 2 Diesel Engine...

  15. Elastomer Compatibility Testing of Renewable Diesel Fuels

    SciTech Connect (OSTI)

    Frame, E.; McCormick, R. L.

    2005-11-01T23:59:59.000Z

    In this study, the integrity and performance of six elastomers were tested with ethanol-diesel and biodiesel fuel blends.

  16. Clean Coal Diesel Demonstration Project

    SciTech Connect (OSTI)

    Robert Wilson

    2006-10-31T23:59:59.000Z

    A Clean Coal Diesel project was undertaken to demonstrate a new Clean Coal Technology that offers technical, economic and environmental advantages over conventional power generating methods. This innovative technology (developed to the prototype stage in an earlier DOE project completed in 1992) enables utilization of pre-processed clean coal fuel in large-bore, medium-speed, diesel engines. The diesel engines are conventional modern engines in many respects, except they are specially fitted with hardened parts to be compatible with the traces of abrasive ash in the coal-slurry fuel. Industrial and Municipal power generating applications in the 10 to 100 megawatt size range are the target applications. There are hundreds of such reciprocating engine power-plants operating throughout the world today on natural gas and/or heavy fuel oil.

  17. An Experimental Investigation of Low Octane Gasoline in Diesel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Publications Use of Low Cetane Fuel to Enable Low Temperature Combustion High-Efficiency, Ultra-Low Emission Combustion in a Heavy-Duty Engine via Fuel Reactivity Control...

  18. Computational Fluid Dynamics Modeling of Diesel Engine Combustion...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Controlled Compression Ignition (RCCI) Combustion in a Light-Duty Engine High-Efficiency, Ultra-Low Emission Combustion in a Heavy-Duty Engine via Fuel Reactivity Control...

  19. Diesel prices continue to decrease

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavid TurnerExperimental CapabilitiesDieselDiesel

  20. Diesel prices continue to decrease

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavid TurnerExperimentalDiesel prices continueDiesel

  1. Diesel prices continue to decrease

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavid TurnerExperimentalDiesel pricesDiesel prices

  2. Diesel prices continue to decrease

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavid TurnerExperimentalDiesel pricesDiesel

  3. Diesel prices continue to fall

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavid TurnerExperimentalDieselDiesel prices

  4. Diesel prices continue to increase

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavid TurnerExperimentalDieselDiesel

  5. Diesel prices continue to increase

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel prices continue to increase TheDiesel

  6. Diesel prices continue to rise

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel prices continue to increaseDiesel prices

  7. Diesel prices slightly decrease nationally

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel pricesDiesel prices slightly

  8. Diesel prices up this week

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel pricesDiesel prices

  9. Biodiesel and Other Renewable Diesel Fuels

    SciTech Connect (OSTI)

    Not Available

    2006-11-01T23:59:59.000Z

    Present federal tax incentives apply to certain types of biomass-derived diesel fuels, which in energy policy and tax laws are described either as renewable diesel or biodiesel. To understand the distinctions between these diesel types it is necessary to understand the technologies used to produce them and the properties of the resulting products. This fact sheet contains definitions of renewable and biodiesel and discusses the processes used to convert biomass to diesel fuel and the properties of biodiesel and renewable diesel fuels.

  10. Physical properties of bio-diesel & Implications for use of bio-diesel in diesel engines

    SciTech Connect (OSTI)

    Chakravarthy, Veerathu K [ORNL; McFarlane, Joanna [ORNL; Daw, C Stuart [ORNL; Ra, Youngchul [ORNL; Griffin, Jelani K [ORNL; Reitz, Rolf [University of Wisconsin

    2008-01-01T23:59:59.000Z

    In this study we identify components of a typical biodiesel fuel and estimate both their individual and mixed thermo-physical and transport properties. We then use the estimated mixture properties in computational simulations to gauge the extent to which combustion is modified when biodiesel is substituted for conventional diesel fuel. Our simulation studies included both regular diesel combustion (DI) and premixed charge compression ignition (PCCI). Preliminary results indicate that biodiesel ignition is significantly delayed due to slower liquid evaporation, with the effects being more pronounced for DI than PCCI. The lower vapor pressure and higher liquid heat capacity of biodiesel are two key contributors to this slower rate of evaporation. Other physical properties are more similar between the two fuels, and their impacts are not clearly evident in the present study. Future studies of diesel combustion sensitivity to both physical and chemical properties of biodiesel are suggested.

  11. CORPORATE OVERVIEW AMEREN CORPORATION

    E-Print Network [OSTI]

    Subramanian, Venkat

    regional), distribution · Natural gas: sales, transmission & distribution · Sources: Hydro, Ultra-low-sulfur

  12. Coal-fired diesel generator

    SciTech Connect (OSTI)

    NONE

    1997-05-01T23:59:59.000Z

    The objective of the proposed project is to test the technical, environmental, and economic viability of a coal-fired diesel generator for producing electric power in small power generating markets. Coal for the diesel generator would be provided from existing supplies transported for use in the University`s power plant. A cleanup system would be installed for limiting gaseous and particulate emissions. Electricity and steam produced by the diesel generator would be used to supply the needs of the University. The proposed diesel generator and supporting facilities would occupy approximately 2 acres of land adjacent to existing coal- and oil-fired power plant and research laboratory buildings at the University of Alaska, Fairbanks. The environmental analysis identified that the most notable changes to result from the proposed project would occur in the following areas: power plant configuration at the University of Alaska, Fairbanks; air emissions, water use and discharge, and the quantity of solid waste for disposal; noise levels at the power plant site; and transportation of coal to the power plant. No substantive adverse impacts or environmental concerns were identified in analyzing the effects of these changes.

  13. Sugar yields from dilute sulfuric acid and sulfur dioxide pretreatments and subsequent enzymatic hydrolysis of switchgrass

    E-Print Network [OSTI]

    California at Riverside, University of

    Sugar yields from dilute sulfuric acid and sulfur dioxide pretreatments and subsequent enzymatic Dilute sulfuric acid Sulfur dioxide Biofuels Switchgrass a b s t r a c t Dacotah switchgrass was pretreated with sulfuric acid concentrations of 0.5, 1.0, and 2.0 wt.% at 140, 160, and 180 °C and with 1

  14. Graphene-sulfur nanocomposites for rechargeable lithium-sulfur battery electrodes

    SciTech Connect (OSTI)

    Liu, Jun; Lemmon, John P; Yang, Zhenguo; Cao, Yuiliang; Li, Xiaolin

    2014-06-17T23:59:59.000Z

    Rechargeable lithium-sulfur batteries having a cathode that includes a graphene-sulfur nanocomposite can exhibit improved characteristics. The graphene-sulfur nanocomposite can be characterized by graphene sheets with particles of sulfur adsorbed to the graphene sheets. The sulfur particles have an average diameter less than 50 nm..

  15. Sulfur-Free Selective Pulping

    E-Print Network [OSTI]

    Dimmel, D. R.; Bozell, J. J.

    A joint research effort is being conducted on ways to produce cost-effective pulping catalysts from lignin. This project addresses improving selectivities and reducing the levels of sulfur chemicals used in pulping. Improved selectivity means...

  16. Deep desulfurization of hydrocarbon fuels

    DOE Patents [OSTI]

    Song, Chunshan (State College, PA); Ma, Xiaoliang (State College, PA); Sprague, Michael J. (Calgary, CA); Subramani, Velu (State College, PA)

    2012-04-17T23:59:59.000Z

    The invention relates to processes for reducing the sulfur content in hydrocarbon fuels such as gasoline, diesel fuel and jet fuel. The invention provides a method and materials for producing ultra low sulfur content transportation fuels for motor vehicles as well as for applications such as fuel cells. The materials and method of the invention may be used at ambient or elevated temperatures and at ambient or elevated pressures without the need for hydrogen.

  17. Activity and structure of perovskites as diesel reforming catalysts for solid oxide fuel cells.

    SciTech Connect (OSTI)

    Liu, D.-J.; Krumpelt, M.; Chemical Engineering

    2005-01-01T23:59:59.000Z

    Recent progress in developing perovskite materials as more cost-effective catalysts in autothermal reforming (ATR) of diesel fuel to hydrogen-rich reformate for solid oxide fuel cell (SOFC) application is reported. Perovskite-type metal oxides with B sites partially exchanged by ruthenium were prepared and evaluated under ATR reaction conditions. The hydrogen yield, reforming efficiency, and CO{sub x} selectivity of these catalysts were investigated using diesel surrogate fuel with 50 ppm sulfur. The catalyst performances have approached or exceeded a benchmark, high-cost rhodium-based material. In parallel with the reactivity study, we also investigated the physical properties of B-site doped perovskites and their impact on the reforming performance using various characterization techniques such as BET, X-ray powder diffraction, temperature programmable reduction, scanning electron microscopy, and synchrotron X-ray absorption spectroscopy. We found that ruthenium is highly dispersed into perovskite lattice and its redox behavior is directly associated with reforming activity.

  18. An Enabling Study of Diesel Low-Temperautre Combustion via Adaptive...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications Boosted HCCI for High Power without Engine Knock, and with Ultra-Low NOX Emissions Low Temperature Combustion Demonstrator for High Efficiency Clean...

  19. Edinburgh Research Explorer Pulmonary diesel particulate increases susceptibility to

    E-Print Network [OSTI]

    Millar, Andrew J.

    Edinburgh Research Explorer Pulmonary diesel particulate increases susceptibility to myocardial, MR & Gray, GA 2014, 'Pulmonary diesel particulate increases susceptibility to myocardial ischemia. Pulmonary diesel particulate increases susceptibility to myocardial ischemia/reperfusion injury via

  20. A Comparison of Combustion and Emissions of Diesel Fuels and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    A Comparison of Combustion and Emissions of Diesel Fuels and Oxygenated Fuels in a Modern DI Diesel Engine A Comparison of Combustion and Emissions of Diesel Fuels and Oxygenated...

  1. Cutting NOx from Diesel Engines with Membrane-Generated Nitrogen...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Cutting NOx from Diesel Engines with Membrane-Generated Nitrogen-Enriched Air Cutting NOx from Diesel Engines with Membrane-Generated Nitrogen-Enriched Air 2005 Diesel Engine...

  2. REVIEW OF DIESEL PARTICULATE MATTER SAMPLING METHODS Supplemental Report # 2

    E-Print Network [OSTI]

    Minnesota, University of

    REVIEW OF DIESEL PARTICULATE MATTER SAMPLING METHODS Supplemental Report # 2 AEROSOL DYMAMICS Arnold University of Minnesota Department of Mechanical Engineering Center for Diesel Research................................................................................................. 3 Diesel aerosol composition and structure................................................... 3

  3. Selective catalytic reduction of sulfur dioxide to elemental sulfur

    SciTech Connect (OSTI)

    Liu, Wei; Flytzani-Stephanopoulos, M.; Sarofim, A.F.

    1992-01-01T23:59:59.000Z

    Elemental sulfur recovery from SO[sub 2]-containing gas streams is highly attractive as it produces a saleable. Product and no waste to dispose of. However, commercially available schemes are complex and involve multi-stage reactors, such as, most notably in the Resox (reduction of SO[sub 2] with coke) and Claus plants(reaction of SO[sub 2] with H[sub 2]S over catalyst). This project win investigate a cerium oxide catalyst for the single-stage selective reduction SO[sub 2] to elemental sulfur by a reductant, such as carbon monoxide. Cerium oxide has been identified as a superior catalyst for SO[sub 2] reduction by CO to elemental sulfur because of its high activity and high selectivity to sulfur over COS over a wide temperature range(400--650C). Kinetic and parametric studies of SO[sub 2] reduction planned over various CeO[sub 2]-formulations will provide the necessary basis for development of a simplified process, a single-stage elemental sulfur recovery scheme from variable concentration gas streams. A first apparent application is treatment of regenerator off-gases in power plants using regenerative flue gas desulfurization. Such a simple catalytic converter may offer the long-sought Claus-alternative'' for coal-fired power plant applications.

  4. KIVA Modeling to Support Diesel Combustion Research

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    DOE Merit Review KIVA Modeling to Support Diesel Combustion Research DOE Vehicle Technologies Program Annual Merit Review, FY2008 David Torres Los Alamos National Laboratory...

  5. Diesel Particulate Filtration (DPF) Technology: Success stories...

    Broader source: Energy.gov (indexed) [DOE]

    Diesel Particulate Filtration (DPF) Technology: Success stories at the High Temperature Materials Laboratory (HTML) User Program Dr. Amit Shyam, ORNL Sponsored by U.S. Department...

  6. Advanced Diesel Engine and Aftertreatment Technology Development...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Aftertreatment Technology Development for Tier 2 Emissions Advanced Diesel Engine and Aftertreatment Technology Development for Tier 2 Emissions 2003 DEER Conference...

  7. Diesel Particulate Filtration (DPF) Technology: Success stories...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Success stories at the High Temperature Materials Laboratory (HTML) User Program Diesel Particulate Filtration (DPF) Technology: Success stories at the High Temperature...

  8. Advanced Ceramic Filter For Diesel Emission Control

    Broader source: Energy.gov (indexed) [DOE]

    Diesel Emission Control Frank Mao, Cheng G. Li, Ravi Ramanathan Dow Automotive 3900 Automation Ave. Auburn Hills, MI 48326 9272004 DEER2004 2 Outline of Presentation Dow...

  9. Comparison of Conventional Diesel and Reactivity Controlled...

    Broader source: Energy.gov (indexed) [DOE]

    DEER 10182012 Comparison of Conventional Diesel and Reactivity Controlled Compression Ignition (RCCI) Combustion in a Light-Duty Engine Rolf D. Reitz and Sage L. Kokjohn Engine...

  10. Indiana: Improving Diesel Engine Performance for Trucks

    Office of Energy Efficiency and Renewable Energy (EERE)

    Cummins, the world's largest diesel engine manufacturer, received funds from EERE to research advanced engine technology for heavy-duty and light-duty vehicles.

  11. Tailored Acicular Mullite Substrates for Multifunctional Diesel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    deer09malanga.pdf More Documents & Publications Future Trends for DPFSCR On-Filter (SCRF) fundamental Modeling and Experimental Studies of Acicular Mullite Diesel Particulate...

  12. Multicylinder Diesel Engine Design for HCCI Operation

    Broader source: Energy.gov (indexed) [DOE]

    7 DEER Detroit August 12-16 Multicylinder Diesel Engine Design for HCCI operation William de Ojeda Phil Zoldak, Ral Espinoza, Raj Kumar, Chunyi Xia, Dan Cornelius International...

  13. Electrochemical NOx Sensor for Monitoring Diesel Emissions

    Broader source: Energy.gov (indexed) [DOE]

    oil consumption by about 1.5 million barrels per day. * Advantages of diesel technology: - Provides exceptional fuel economy - Completely compatible with biodiesel...

  14. BMW Diesel Engines - Dynamic, Efficient and Clean

    Broader source: Energy.gov (indexed) [DOE]

    Nrburgring 2001 - DI with 2nd generation Common Rail, 1600 bar 2004 - Variable Twin Turbo - Particulate filter 2nd generation 1999 - First V8 diesel with direct injection...

  15. Optimization of Advanced Diesel Engine Combustion Strategies

    Broader source: Energy.gov (indexed) [DOE]

    - UW-ERC 1 "University Research in Advanced Combustion and Emissions Control" Optimization of Advanced Diesel Engine Combustion Strategies Profs. Rolf Reitz, D. Foster, J....

  16. Low-Temperature Automotive Diesel Combustion

    Broader source: Energy.gov (indexed) [DOE]

    Automotive Diesel Combustion Light-Duty Combustion Experiments Paul Miles Sandia National Laboratories Light-Duty Combustion Modeling Rolf Reitz University of Wisconsin June 8,...

  17. Diesel prices top $4 per gallon

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel pricesDiesel prices slightlyDieselDiesel

  18. Diesel prices see slight drop

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management FermiDavidDiesel prices

  19. Adaptive Control to Improve Low Temperature Diesel Engine Combustion...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Control to Improve Low Temperature Diesel Engine Combustion Adaptive Control to Improve Low Temperature Diesel Engine Combustion Presentation given at DEER 2006, August 20-24,...

  20. Modeling Combustion Control for High Power Diesel Mode Switching...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Combustion Control for High Power Diesel Mode Switching Modeling Combustion Control for High Power Diesel Mode Switching Poster presentation given at the 16th Directions in...

  1. AVTA: 2009 Volkswagen Jetta TDI Diesel Downloadable Dynamometer...

    Energy Savers [EERE]

    09 Volkswagen Jetta TDI Diesel Downloadable Dynamometer Database Reports AVTA: 2009 Volkswagen Jetta TDI Diesel Downloadable Dynamometer Database Reports The Vehicle Technologies...

  2. AVTA: 2010 Volkswagon Golf Diesel Start-Stop Testing Results...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Volkswagon Golf Diesel Start-Stop Testing Results AVTA: 2010 Volkswagon Golf Diesel Start-Stop Testing Results The Vehicle Technologies Office's Advanced Vehicle Testing Activity...

  3. Global kinetics for a commercial diesel oxidation catalyst with...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    kinetics for a commercial diesel oxidation catalyst with two exhaust hydrocarbons Global kinetics for a commercial diesel oxidation catalyst with two exhaust hydrocarbons...

  4. Development of an Accelerated Ash-Loading Protocol for Diesel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    an Accelerated Ash-Loading Protocol for Diesel Particulate Filters Development of an Accelerated Ash-Loading Protocol for Diesel Particulate Filters Poster presentation at the 2007...

  5. Local Soot Loading Distribution in Cordierite Diesel Particulate...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Local Soot Loading Distribution in Cordierite Diesel Particulate Filters by Dynamic Neutron Radiography Local Soot Loading Distribution in Cordierite Diesel Particulate Filters by...

  6. Low-Temperature Diesel Combustion Cross-Cut Research

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Diesel Combustion Cross-Cut Research Low-Temperature Diesel Combustion Cross-Cut Research Lyle M. Pickett Combustion Research Facility Sandia National Laboratories Sponsor: DOEOVT...

  7. Oxygen-Enriched Combustion for Military Diesel Engine Generators...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Oxygen-Enriched Combustion for Military Diesel Engine Generators Oxygen-Enriched Combustion for Military Diesel Engine Generators Substantial increases in brake power and...

  8. Dilute Clean Diesel Combustion Achieves Low Emissions and High...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Dilute Clean Diesel Combustion Achieves Low Emissions and High Efficiency While Avoiding Control Problems of HCCI Dilute Clean Diesel Combustion Achieves Low Emissions and High...

  9. Complete Fuel Combustion for Diesel Engines Resulting in Greatly...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Complete Fuel Combustion for Diesel Engines Resulting in Greatly Reduced Emissions and Improved Fuel Efficiency Complete Fuel Combustion for Diesel Engines Resulting in Greatly...

  10. Low Temperature Combustion and Diesel Emission Reduction Research...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Diesel Emission Reduction Research Low Temperature Combustion and Diesel Emission Reduction Research Presentation given at DEER 2006, August 20-24, 2006, Detroit, Michigan....

  11. Hydrogen Assisted Diesel Combustion in a Common Rail Turbodiesel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Assisted Diesel Combustion in a Common Rail Turbodiesel Engine Hydrogen Assisted Diesel Combustion in a Common Rail Turbodiesel Engine This study measured the effects of hydrogen...

  12. Emissions and Durability of Underground Mining Diesel Particulate...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Durability of Underground Mining Diesel Particulate Filter Applications Emissions and Durability of Underground Mining Diesel Particulate Filter Applications Presentation given at...

  13. Durability of Diesel Engine Particulate Filters (Agreement ID...

    Broader source: Energy.gov (indexed) [DOE]

    Durability of Diesel Engine Particulate Filters (Agreement ID:10461) Durability of Diesel Engine Particulate Filters (Agreement ID:10461) 2013 DOE Hydrogen and Fuel Cells Program...

  14. Hydrogen Assisted Diesel Combustion in a Common Rail Turbodiesel...

    Broader source: Energy.gov (indexed) [DOE]

    Assisted Diesel Combustion in a Common Rail Turbodiesel Engine P-3 Hydrogen Assisted Diesel Combustion in a Common Rail Turbodiesel Engine P-3 Gregory Lilik, Jos Martn...

  15. Design Case Summary: Production of Gasoline and Diesel from Biomass...

    Energy Savers [EERE]

    Design Case Summary: Production of Gasoline and Diesel from Biomass via Fast Pyrolysis, Hydrotreating, and Hydrocracking Design Case Summary: Production of Gasoline and Diesel from...

  16. Production of Gasoline and Diesel from Biomass via Fast Pyrolysis...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Production of Gasoline and Diesel from Biomass via Fast Pyrolysis, Hydrotreating and Hydrocracking: A Design Case Production of Gasoline and Diesel from Biomass via Fast Pyrolysis,...

  17. Advanced Radio Frequency-Based Sensors for Monitoring Diesel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Radio Frequency-Based Sensors for Monitoring Diesel Particulate Filter Loading and Regeneration Advanced Radio Frequency-Based Sensors for Monitoring Diesel Particulate Filter...

  18. Update on Diesel Exhaust Emission Control Technology and Regulations...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Control Technology and Regulations Update on Diesel Exhaust Emission Control Technology and Regulations 2004 Diesel Engine Emissions Reduction (DEER) Conference Presentation:...

  19. Improvement and Simplification of Diesel Particulate Filter System...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Improvement and Simplification of Diesel Particulate Filter System using a Ceria-Based Fuel-Borne Catalyst in Serial Applications Improvement and Simplification of Diesel...

  20. Radio Frequency Diesel Particulate Filter Sensor Reduces Fuel...

    Office of Environmental Management (EM)

    Radio Frequency Diesel Particulate Filter Sensor Reduces Fuel Consumption, Wins R&D 100 Award Radio Frequency Diesel Particulate Filter Sensor Reduces Fuel Consumption, Wins R&D...

  1. Modeling of Diesel Exhaust Systems: A methodology to better simulate...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Diesel Exhaust Systems: A methodology to better simulate soot reactivity Modeling of Diesel Exhaust Systems: A methodology to better simulate soot reactivity Discussed...

  2. Combination of Diesel fuel system architectures and Ceria-based...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Diesel fuel system architectures and Ceria-based fuel-borne catalysts for improvement and simplification of the Diesel Particulate Filter System in serial applications...

  3. Simplification of Diesel Emission Control System Packaging Using...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Simplification of Diesel Emission Control System Packaging Using SCR Coated on DPF Simplification of Diesel Emission Control System Packaging Using SCR Coated on DPF Study...

  4. Recent Diesel Engine Emission Mitigation Activities of the Maritime...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Diesel Engine Emission Mitigation Activities of the Maritime Administration Energy Technologies Program Recent Diesel Engine Emission Mitigation Activities of the Maritime...

  5. 12TH DIESEL ENGINE-EFFICIENCY AND EMISSIONS RESEARCH CONFERENCE...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    2TH DIESEL ENGINE-EFFICIENCY AND EMISSIONS RESEARCH CONFERENCE (DEER 2006) PRESENTATIONS 12TH DIESEL ENGINE-EFFICIENCY AND EMISSIONS RESEARCH CONFERENCE (DEER 2006) PRESENTATIONS...

  6. New Cordierite Diesel Particulate Filters for Catalyzed and Non...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Cordierite Diesel Particulate Filters for Catalyzed and Non-Catalyzed Applications New Cordierite Diesel Particulate Filters for Catalyzed and Non-Catalyzed Applications 2003 DEER...

  7. Mixed-mode diesel HCCI with External Mixture Formation: Preliminary...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Mixed-mode diesel HCCI with External Mixture Formation: Preliminary Results Mixed-mode diesel HCCI with External Mixture Formation: Preliminary Results 2003 DEER Conference...

  8. Measurement of diesel solid nanoparticle emissions using a catalytic...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    diesel solid nanoparticle emissions using a catalytic stripper for comparison with Europe's PMP protocol Measurement of diesel solid nanoparticle emissions using a catalytic...

  9. Advances in Diesel Engine Technologies for European Passenger...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Diesel Engine Technologies for European Passenger Vehicles Advances in Diesel Engine Technologies for European Passenger Vehicles 2002 DEER Conference Presentation: Volkswagen AG...

  10. CARB Verification of Catalyzed Diesel Particulate Filters for...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    CARB Verification of Catalyzed Diesel Particulate Filters for Emergency Generator Sets CARB Verification of Catalyzed Diesel Particulate Filters for Emergency Generator Sets 2005...

  11. Load Expansion with Diesel/Gasoline RCCI for Improved Engine...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    with DieselGasoline RCCI for Improved Engine Efficiency and Emissions Load Expansion with DieselGasoline RCCI for Improved Engine Efficiency and Emissions This poster will...

  12. Comparison of Conventional Diesel and Reactivity Controlled Compressio...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Conventional Diesel and Reactivity Controlled Compression Ignition (RCCI) Combustion in a Light-Duty Engine Comparison of Conventional Diesel and Reactivity Controlled Compression...

  13. Ultra-Lite Diesel Particulate Filter Cartridge for Reduced Regeneratio...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Lite Diesel Particulate Filter Cartridge for Reduced Regeneration Time and Fuel Consumption Ultra-Lite Diesel Particulate Filter Cartridge for Reduced Regeneration Time and Fuel...

  14. Attaining Tier 2 Emissions Through Diesel Engine and Aftertreatment...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Attaining Tier 2 Emissions Through Diesel Engine and Aftertreatment Integration - Strategy and Experimental Results Attaining Tier 2 Emissions Through Diesel Engine and...

  15. Versatile Diesel Particulate Filter Cartridge Any Size, Any Shape...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Versatile Diesel Particulate Filter Cartridge Any Size, Any Shape Versatile Diesel Particulate Filter Cartridge Any Size, Any Shape Presentation given at DEER 2006, August 20-24,...

  16. Advanced Diesel Common Rail Injection System for Future Emission...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Common Rail Injection System for Future Emission Legislation Advanced Diesel Common Rail Injection System for Future Emission Legislation 2004 Diesel Engine Emissions Reduction...

  17. Heavy Truck Clean Diesel (HTCD) Program: 2007 Demonstration Truck...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Clean Diesel (HTCD) Program: 2007 Demonstration Truck Heavy Truck Clean Diesel (HTCD) Program: 2007 Demonstration Truck 2003 DEER Conference Presentation: Caterpillar Incorporated...

  18. Effects of Diesel Exhaust Emissions on Soot Oxidation and DPF...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Diesel Exhaust Emissions on Soot Oxidation and DPF Regeneration Effects of Diesel Exhaust Emissions on Soot Oxidation and DPF Regeneration DPF regeneration experiments verified the...

  19. Fuel Formulation Effects on Diesel Fuel Injection, Combustion...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Formulation Effects on Diesel Fuel Injection, Combustion, Emissions and Emission Control Fuel Formulation Effects on Diesel Fuel Injection, Combustion, Emissions and Emission...

  20. Microwave Regenerated DPF for Auxiliary Power Units and Diesel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Microwave Regenerated DPF for Auxiliary Power Units and Diesel Hybrid Vehicles Microwave Regenerated DPF for Auxiliary Power Units and Diesel Hybrid Vehicles Microwave regeneration...