Powered by Deep Web Technologies
Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Investigation of materials performances in high moisture environments including corrosive contaminants typical of those arising by using alternative fuels in gas turbines  

NLE Websites -- All DOE Office Websites (Extended Search)

materials performances in high moisture materials performances in high moisture environments including corrosive contaminants typical of those arising by using alternative fuels in gas turbines Gerald Meier, Frederick Pettit and Keeyoung Department of Materials Science and Engineering, Jung University of Pittsburgh Pittsburgh, PA 15260 Peer review Workshop III UTSR Project 04 01 SR116 October 18-20, 2005 Project Approach Task I Selection and Preparation of Specimens Task II Selection of Test Conditions Specimens : GTD111+CoNiCrAlY and Pt Aluminides, N5+Pt Aluminides Deposit : No Deposit, CaO, CaSO 4 , Na 2 SO 4 1150℃ Dry 1150℃ Wet 950℃ Wet 750℃ SO 3 950℃ Dry Selection of Test Temperature, T 1 , Gas Environment and Deposit Composition, D

2

Residential sidewall insulation case histories, including experiences and problems in the field application of loose fill  

SciTech Connect

An unbonded fiberglass loose-fill insulation was selected for this sidewall application study. The insert tube technique is described and the parameters that affect pneumatic application of the product are identified. The initial evaluation was conducted in the laboratory and included density and thermal testing. The laboratory results were then utilized in field studies. Ten homes with no sidewall insulation were retrofitted. Thermographic scans of sidewalls before and after retrofit confirmed the predicted reductions in heat loss based on calculation techniques given in the ASHRAE Handbook of Fundamentals. The improvement was further confirmed by comparing utility bills. Typical problems that occur while preparing a house for sidewall retrofit are discussed. The simple payback for typical houses is presented. Good correlation is shown between laboratory test results and field performance. Test data indicate that the application procedure used gave an effective R-value per product claim.

Infante, L.J.; Aller, P.F.; Fay, R.E.

1983-01-01T23:59:59.000Z

3

Greenhouse gases emissions accounting for typical sewage sludge digestion with energy utilization and residue land application in China  

Science Conference Proceedings (OSTI)

Highlights: Black-Right-Pointing-Pointer GHGs emissions from sludge digestion + residue land use in China were calculated. Black-Right-Pointing-Pointer The AD unit contributes more than 97% of total biogenic GHGs emissions. Black-Right-Pointing-Pointer AD with methane recovery is attractive for sludge GHGs emissions reduction. - Abstract: About 20 million tonnes of sludge (with 80% moisture content) is discharged by the sewage treatment plants per year in China, which, if not treated properly, can be a significant source of greenhouse gases (GHGs) emissions. Anaerobic digestion is a conventional sewage sludge treatment method and will continue to be one of the main technologies in the following years. This research has taken into consideration GHGs emissions from typical processes of sludge thickening + anaerobic digestion + dewatering + residue land application in China. Fossil CO{sub 2}, biogenic CO{sub 2}, CH{sub 4,} and avoided CO{sub 2} as the main objects is discussed respectively. The results show that the total CO{sub 2}-eq is about 1133 kg/t DM (including the biogenic CO{sub 2}), while the net CO{sub 2}-eq is about 372 kg/t DM (excluding the biogenic CO{sub 2}). An anaerobic digestion unit as the main GHGs emission source occupies more than 91% CO{sub 2}-eq of the whole process. The use of biogas is important for achieving carbon dioxide emission reductions, which could reach about 24% of the total CO{sub 2}-eq reduction.

Niu Dongjie, E-mail: niudongjie@tongji.edu.cn [Key Laboratory of Yangtze Aquatic Environment, Ministry of Education, College of Environmental Science and Engineering of Tongji University, 1239 Siping Road, Shanghai 200092 (China); UNEP-Tongji Institute of Environment for Sustainable Development, 1239 Siping Road, Shanghai 200092 (China); Huang Hui [Key Laboratory of Yangtze Aquatic Environment, Ministry of Education, College of Environmental Science and Engineering of Tongji University, 1239 Siping Road, Shanghai 200092 (China); Dai Xiaohu [Key Laboratory of Yangtze Aquatic Environment, Ministry of Education, College of Environmental Science and Engineering of Tongji University, 1239 Siping Road, Shanghai 200092 (China); National Engineering Research Center for Urban Pollution Control, Shanghai 200092 (China); Zhao Youcai [Key Laboratory of Yangtze Aquatic Environment, Ministry of Education, College of Environmental Science and Engineering of Tongji University, 1239 Siping Road, Shanghai 200092 (China)

2013-01-15T23:59:59.000Z

4

Microwave technology for waste management applications including disposition of electronic circuitry  

SciTech Connect

Microwave technology is being developed nationally and internationally for a variety of environmental remediation purposes. These efforts include treatment and destruction of a vast array of gaseous, liquid and solid hazardous wastes as well as subsequent immobilization of selected components. Microwave technology provides an important contribution to an arsenal of existing remediation methods that are designed to protect the public and environment from undesirable consequences of hazardous materials. Applications of microwave energy for environmental remediation will be discussed. Emphasized will be a newly developed microwave process designed to treat discarded electronic circuitry and reclaim the precious metals within for reuse.

Wicks, G.G. [Westinghouse Savannah River Co., Aiken, SC (United States); Clark, D.E.; Schulz, R.L.; Folz, D.C. [Univ. of Florida, Gainesville, FL (United States)

1995-09-01T23:59:59.000Z

5

Abstract-A hybrid cascaded multilevel inverter application for renewable energy resources including a reconfiguration  

E-Print Network (OSTI)

, micro-turbine, wind turbine and fuel cell put forward many promising applications with high efficiency, a high power converter (about 100 kW) with high quality output voltage waveform, high efficiency (PowerSim) and Simulink/MATLAB are used to simulate the circuit operation and control signal. A 3-kW

Tolbert, Leon M.

6

Application of exterior complex scaling to positron-hydrogencollisions including rearrangement  

SciTech Connect

The first application of an exterior complex scaling method to an atomic scattering problem with distinct rearrangement channels is reported. Calculations are performed for positron-hydrogen collisions in an s-wave model employing an electron-positron potential of V{sub 12} = -(8+(r{sub 1}-r{sub 2}){sup 2}){sup 1/2}, using the time-independent propagating exterior complex scaling (PECS) method. This potential has the correct long-range Coulomb tail of the full problem and the results demonstrate that ECS-based methods can accurately calculate scattering, ionization and positronium formation cross sections in this three-body rearrangement collision.

Bartlett, Philip L.; Stelbovics, Andris T.; Rescigno, Thomas N.; McCurdy, C. William

2007-12-06T23:59:59.000Z

7

Resonance Evaluation of 48Ti Including Covariance for Criticality Safety Applications  

Science Conference Proceedings (OSTI)

In this work we report the methodology and the results of an evaluation carried out for 48Ti in the resolved resonance region for applications in criticality safety calculations. The evaluation was performed using the computer code SAMMY with the reduced R-matrix Reich-Moore formalism. The Bayes scheme was utilized for fitting the experimental data. New transmission and capture data were essential in the evaluation process. A complete set of resonance parameters was obtained in the energy region from thermal to 400 keV. In addition to the resonance parameters, a resonance parameter covariance matrix was also obtained. The impact of the new resonance parameter evaluation in benchmark calculations, as well as the uncertainty, was verified.

Leal, Luiz C [ORNL; Guber, Klaus H [ORNL; Arbanas, Goran [ORNL; Wiarda, Dorothea [ORNL; Koehler, Paul Edward [ORNL; Kahler, A. [Los Alamos National Laboratory (LANL)

2011-01-01T23:59:59.000Z

8

Nuclear Maintenance Applications Center: Motor Management Guide Supporting Plant License Renewal Including Environmental Qualification Considerations  

Science Conference Proceedings (OSTI)

This report was developed by the Electric Power Research Institutes Large Electric Motor Users Group Information Working Group, which includes motor engineers, motor specialist consultants, and vendors. Environmental qualification (EQ) program owners were also involved in the development of this report. This report addresses the most important elements of a sound motor management program to support an informed decision on motor preservation and motor life extension. Motor life extensions of ...

2013-06-07T23:59:59.000Z

9

UCSC EMPLOYEE HOUSING APARTMENTS APPLICATION Rental rates include: rent, refuse collection, common area utilities, groundskeeping services, and repairs and  

E-Print Network (OSTI)

UCSC EMPLOYEE HOUSING APARTMENTS APPLICATION Rental rates include: rent, refuse collection, common. Tenants pay for their own utilities (i.e., electricity, gas, water, telephone and cable services). A $750 for current rental rates): 1 bedroom 1 bdrm deluxe 2 bdrm/1 bath 2 bdrm/2 bath) If you are interested in a two

California at Santa Cruz, University of

10

Applications  

Science Conference Proceedings (OSTI)

Table 6   Typical applications of duplex stainless steels...salt evaporation equipment, desalination plants, geothermal

11

Omega-3 Oils: Applications in Functional FoodsChapter 3 Fish Sources of Various Lipids Including n-3 Polyunsaturated Fatty Acids and Their Dietary Effects  

Science Conference Proceedings (OSTI)

Omega-3 Oils: Applications in Functional Foods Chapter 3 Fish Sources of Various Lipids Including n-3 Polyunsaturated Fatty Acids and Their Dietary Effects Health Nutrition Biochemistry eChapters Health - Nutrition - Biochemistry 448930

12

FORMALISM FOR INCLUSION OF MEASURED REACTION CROSS SECTIONS IN STELLAR RATES INCLUDING UNCERTAINTIES AND ITS APPLICATION TO NEUTRON CAPTURE IN THE s-PROCESS  

Science Conference Proceedings (OSTI)

A general formalism to include experimental reaction cross sections into calculations of stellar rates is presented. It also allows us to assess the maximally possible reduction of uncertainties in the stellar rates by experiments. As an example for the application of the procedure, stellar neutron capture reactivities from KADoNiS v0.3 are revised and the remaining uncertainties shown. Many of the uncertainties in the stellar rates are larger than those obtained experimentally. This has important consequences for s-process models and the interpretation of meteoritic data because it allows the rates of some reactions to vary within a larger range than previously assumed.

Rauscher, Thomas [Department of Physics, University of Basel, CH-4056 Basel (Switzerland)

2012-08-10T23:59:59.000Z

13

A generalized window energy rating system for typical office buildings  

Science Conference Proceedings (OSTI)

Detailed computer simulation programs require lengthy inputs, and cannot directly provide an insight to relationship between the window energy performance and the key window design parameters. Hence, several window energy rating systems (WERS) for residential houses and small buildings have been developed in different countries. Many studies showed that utilization of daylight through elaborate design and operation of windows leads to significant energy savings in both cooling and lighting in office buildings. However, the current WERSs do not consider daylighting effect, while most of daylighting analyses do not take into account the influence of convective and infiltration heat gains. Therefore, a generalized WERS for typical office buildings has been presented, which takes all primary influence factors into account. The model includes embodied and operation energy uses and savings by a window to fully reflect interactions among the influence parameters. Reference locations selected for artificial lighting and glare control in the current common simulation practice may cause uncompromised conflicts, which could result in over- or under-estimated energy performance. Widely used computer programs, DOE2 and ADELINE, for hourly daylighting and cooling simulations have their own weaknesses, which may result in unrealistic or inaccurate results. An approach is also presented for taking the advantages of the both programs and avoiding their weaknesses. The model and approach have been applied to a typical office building of Hong Kong as an example to demonstrate how a WERS in a particular location can be established and how well the model can work. The energy effect of window properties, window-to-wall ratio (WWR), building orientation and lighting control strategies have been analyzed, and can be indicated by the localized WERS. An application example also demonstrates that the algebraic WERS derived from simulation results can be easily used for the optimal design of windows in buildings similar to the typical buildings. (author)

Tian, Cheng; Chen, Tingyao; Yang, Hongxing; Chung, Tse-ming [Research Center for Building Environmental Engineering, Department of Building Services Engineering, The Hong Kong Polytechnic University, Hong Kong (China)

2010-07-15T23:59:59.000Z

14

High Temperature Superconductors: From Delivery to Applications (Presentation from 2011 Ernest Orlando Lawrence Award-winner, Dr. Amit Goyal, and including introduction by Energy Secretary, Dr. Steven Chu)  

Science Conference Proceedings (OSTI)

Dr. Amit Goyal, a high temperature superconductivity (HTS) researcher at Oak Ridge National Laboratory, was named a 2011 winner of the Department of Energy's Ernest Orlando Lawrence Award honoring U.S. scientists and engineers for exceptional contributions in research and development supporting DOE and its mission. Winner of the award in the inaugural category of Energy Science and Innovation, Dr. Goyal was cited for his work in 'pioneering research and transformative contributions to the field of applied high temperature superconductivity, including fundamental materials science advances and technical innovations enabling large-scale applications of these novel materials.' Following his basic research in grain-to-grain supercurrent transport, Dr. Goyal focused his energy in transitioning this fundamental understanding into cutting-edge technologies. Under OE sponsorship, Dr. Goyal co-invented the Rolling Assisted Bi-Axially Textured Substrate technology (RABiTS) that is used as a substrate for second generation HTS wires. OE support also led to the invention of Structural Single Crystal Faceted Fiber Substrate (SSIFFS) and the 3-D Self Assembly of Nanodot Columns. These inventions and associated R&D resulted in 7 R&D 100 Awards including the 2010 R&D Magazine's Innovator of the Year Award, 3 Federal Laboratory Consortium Excellence in Technology Transfer National Awards, a DOE Energy100 Award and many others. As a world authority on HTS materials, Dr. Goyal has presented OE-sponsored results in more than 150 invited talks, co-authored more than 350 papers and is a fellow of 7 professional societies.

Goyal, Amit (Oak Ridge National Laboratory)

2012-05-22T23:59:59.000Z

15

Signatures of Heating and Cooling Energy Consumption for Typical AHUs  

E-Print Network (OSTI)

An analysis is performed to investigate the signatures of different parameters on the heating and cooling energy consumption of typical air handling units (AHUs). The results are presented in graphic format. HVAC simulation engineers can use these graphs to make quick and rational decisions during the model calibration, identify faulty parameters, and develop optimized operation and control schedules. An application example is given as well in the paper.

Wei, G.; Liu, M.; Claridge, D. E.

1998-01-01T23:59:59.000Z

16

Annotated compilation of the sources of information related to the usage of electricity in non-industrial applications. [Includes about 400 abstracts and glossary  

SciTech Connect

This report presents a thorough compilation of the sources of information related to the usage of electricity in non-industrial applications, as available in the open literature and from the U.S. electrical power industry. The report's scope encompasses all aspects of: electric load management; end use; and the various methods of acquisition, analysis and implementation of electricity usage data. There are over 400 abstracts; 156 from the Load Research Committee of Association of Edison Illuminating Companies (LRC/AEIC) reports and 264 from the open literature. The abstracts over references containing over 12,000 pages plus about 2,500 references and 6,200 graphs and tables pertinent to electricity usage in non-industrial applications. In addition to the LRC/AEIC abstracts, this document identifies over 100 sources of directly relevant information (in contrast to general interest sources and material of secondary relevance).

1978-07-01T23:59:59.000Z

17

The contact-temperature ignition (CTI) criteria for propagating chemical reactions including the effect of moisture and application to Hanford waste  

SciTech Connect

To assure the continued absence of uncontrolled condensed-phase chemical reactions in connection with the Hanford waste materials, efforts have been underway including both theoretical and experimental investigations to clarify the requirements for such reactions. This document defines the differences and requirements for homogeneous runaway and propagating chemical reactions incuding a discussion of general contact-temperature ignition (CTI) condition for propagating reactions that include the effect of moisture. The CTI condition implies that the contact temperature or interface temperature between reacted and unreacted materials must exceed the ignition temperature and is compared to experimental data including both synthetic ferrocyanide and surrogate organic materials. In all cases, the occurrences of ignition accompanied by self-propagating reactions are consistent with the theoretical anticipations of the CTI condition.

Cash, R.J.

1995-09-27T23:59:59.000Z

18

Energy conservation in typical Asian countries  

SciTech Connect

Various policies and programs have been created to promote energy conservation in Asia. Energy conservation centers, energy conservation standards and labeling, commercial building codes, industrial energy use regulations, and utility demand-side management (DSM) are but a few of them. This article attempts to analyze the roles of these different policies and programs in seven typical Asian countries: China, Indonesia, Japan, Pakistan, South Korea, the Philippines, and Thailand. The conclusions show that the two most important features behind the success policies and programs are (1) government policy support and (2) long-run self-sustainability of financial support to the programs.

Yang, M. [International Inst. for Energy Conservation, Bangkok (Thailand); Rumsey, P. [Supersymmetry USA, Berkeley, CA (United States)

1997-06-01T23:59:59.000Z

19

SPECIAL ACQUISITION REQUIREMENTS ? TYPICAL ISSUES ASSOCIATED...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

(iii) Approving any contractual documents, to include documents defining requirements, incentive plans, and evaluation criteria (iv) Awarding contracts (v) Administering...

20

Application Of A New Semi-Empirical Model For Forming Limit Prediction Of Sheet Material Including Superposed Loads Of Bending And Shearing  

Science Conference Proceedings (OSTI)

The use of lightweight materials offers substantial strength and weight advantages in car body design. Unfortunately such kinds of sheet material are more susceptible to wrinkling, spring back and fracture during press shop operations. For characterization of capability of sheet material dedicated to deep drawing processes in the automotive industry, mainly Forming Limit Diagrams (FLD) are used. However, new investigations at the Institute for Metal Forming Technology have shown that High Strength Steel Sheet Material and Aluminum Alloys show increased formability in case of bending loads are superposed to stretching loads. Likewise, by superposing shearing on in plane uniaxial or biaxial tension formability changes because of materials crystallographic texture. Such mixed stress and strain conditions including bending and shearing effects can occur in deep-drawing processes of complex car body parts as well as subsequent forming operations like flanging. But changes in formability cannot be described by using the conventional FLC. Hence, for purpose of improvement of failure prediction in numerical simulation codes significant failure criteria for these strain conditions are missing. Considering such aspects in defining suitable failure criteria which is easy to implement into FEA a new semi-empirical model has been developed considering the effect of bending and shearing in sheet metals formability. This failure criterion consists of the combination of the so called cFLC (combined Forming Limit Curve), which considers superposed bending load conditions and the SFLC (Shear Forming Limit Curve), which again includes the effect of shearing on sheet metal's formability.

Held, Christian [Hochschul Institute Neckarsulm, Gottlieb-Daimler-Strasse 40, 74172 Neckarsulm (Germany); Liewald, Mathias; Schleich, Ralf [Institute for Metal Forming Technology, Universitaet Stuttgart, Stuttgart (Germany); Sindel, Manfred [AUDI AG, Neckarsulm (Germany)

2010-06-15T23:59:59.000Z

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Production and Handling Slide 42: Typical Depleted Cylinder Storage...  

NLE Websites -- All DOE Office Websites (Extended Search)

Typical Depleted Cylinder Storage Yard Skip Presentation Navigation First Slide Previous Slide Next Slide Last Presentation Table of Contents Typical Depleted Cylinder Storage Yard...

22

Examples of management applications that include ocean  

E-Print Network (OSTI)

Changes timing of discharge-related lifecycle, changes food availability, alters sediment and organic 3 0 2 3 Blackfoot (BFT) 2 3 3 2 3 3 Goose (GSE) 3 3 3 0 3 3 Idaho Falls (IFA) 3 3 3 0 3 3 Lower was restricted to Idaho, so the watersheds that cross state boundaries are assessed only for the Idaho portion

23

Applications  

Science Conference Proceedings (OSTI)

Table 1   Typical properties of common roll welded clad laminates...31 (a) 40 (a) Typically used for commutators in electric motors,

24

Determination of selected elements in SRM 1548a typical diet  

Science Conference Proceedings (OSTI)

Neutron activation analysis (NAA), including instrumental NAA (INAA) and radiochemical NAA, is one of the primary analytical techniques used for the certification of elemental content in biological standard reference materials (SRMs) at the National Institute of Standards and Technology (NIST). SRM 1548a, which is a freeze-dried mixture of typical diet composite based on foods consumed in the United States was analyzed for aluminum, calcium, chlorine, potassium, manganese, and sodium by INAA. This analysis is a part of an ongoing effort to improve the quality of the SRMs by understanding and minimizing all known sources of errors or interferences in NAA. To perform highly accurate INAA, the system was calibrated using multiple primary standards. Homogeneity was also measured for these six elements in 12 samples of SRM 1548a in 250-mg sample sizes. The control samples were used to internally evaluate and cross-check the NAA method.

Tandon, L. [North American Scientific, North Hollywood, CA (United States); Garrity, K.M.; Becker, D.A. [National Inst. of Standards and Technology, Gaithersburg, MD (United States)

1996-12-31T23:59:59.000Z

25

Foodservice Equipment Applications Handbook  

Science Conference Proceedings (OSTI)

A typical foodservice operation may spend 75 percent or more of its energy dollar to provide lighting, refrigeration, ventilation, and miscellaneous end uses. Performance characteristics and operational advantages make electricity an excellent option for powering major cooking equipment. This handbook describes the six most common types of major cooking appliances--griddles, fryers, broilers, ovens, ranges, and kettles--including typical applications and industry purchasing trends. Such information will ...

1996-03-26T23:59:59.000Z

26

How much electricity does a typical nuclear power plant generate ...  

U.S. Energy Information Administration (EIA)

How much electricity does a typical nuclear power plant generate? ... tariff, and demand charge data? How is electricity used in U.S. homes?

27

An Integrated Strategy for Whole Ecological Utilization of Typical ...  

Science Conference Proceedings (OSTI)

... of typical industrial solid wastes, such as titanium-bearing blast furnace slag, high-silicon iron tailing and boron-enriched slag as well as oil shale.

28

Nuclear outages back within typical range since July following ...  

U.S. Energy Information Administration (EIA)

U.S. nuclear generator outages were above the levels of the previous four years in the second quarter of 2011 but have returned to more typical ...

29

Typicality ranking via semi-supervised multiple-instance learning  

Science Conference Proceedings (OSTI)

Most of the existing methods for natural scene categorization only consider whether a sample is relevant or irrelevant to a particular concept. However, for the samples relevant to a certain concept, their typicalities or relevancy scores to the concept ... Keywords: multiple-instance learning, natural scene categorization, semi-supervised learning, typicality ranking

Jinhui Tang; Xian-Sheng Hua; Guo-Jun Qi; Xiuqing Wu

2007-09-01T23:59:59.000Z

30

Energy Use Savings for a Typical New Residential Dwelling Unit...  

NLE Websites -- All DOE Office Websites (Extended Search)

PNNL-88603 Prepared for the U.S. Department of Energy under Contract DE-AC05-76RL01830 Energy Use Savings for a Typical New Residential Dwelling Unit Based on the 2009 and 2012...

31

Energy-Efficient Lighting The typical American family spends more  

E-Print Network (OSTI)

fluorescent light bulbs (CFLs) saves you money in the long run with lower energy bills. CFLs are significant Typical incandescent 75-watt light bulb Compact Fluorescent 18-watt light bulb Purchase cost $0.60 $ 5 that incandescent bulbs use becomes heat while only 10 percent becomes light. CFLs create less heat because more

32

Maximum Photovoltaic Penetration Levels on Typical Distribution Feeders: Preprint  

DOE Green Energy (OSTI)

This paper presents simulation results for a taxonomy of typical distribution feeders with various levels of photovoltaic (PV) penetration. For each of the 16 feeders simulated, the maximum PV penetration that did not result in steady-state voltage or current violation is presented for several PV location scenarios: clustered near the feeder source, clustered near the midpoint of the feeder, clustered near the end of the feeder, randomly located, and evenly distributed. In addition, the maximum level of PV is presented for single, large PV systems at each location. Maximum PV penetration was determined by requiring that feeder voltages stay within ANSI Range A and that feeder currents stay within the ranges determined by overcurrent protection devices. Simulations were run in GridLAB-D using hourly time steps over a year with randomized load profiles based on utility data and typical meteorological year weather data. For 86% of the cases simulated, maximum PV penetration was at least 30% of peak load.

Hoke, A.; Butler, R.; Hambrick, J.; Kroposki, B.

2012-07-01T23:59:59.000Z

33

Is the Sun Embedded in a Typical Interstellar Cloud?  

E-Print Network (OSTI)

The physical properties and kinematics of the partially ionized interstellar material near the Sun are typical of warm diffuse clouds in the solar vicinity. The interstellar magnetic field at the heliosphere and the kinematics of nearby clouds are naturally explained in terms of the S1 superbubble shell. The interstellar radiation field at the Sun appears to be harder than the field ionizing ambient diffuse gas, which may be a consequence of the low opacity of the tiny cloud surrounding the heliosphere. The spatial context of the Local Bubble is consistent with our location in the Orion spur.

P. C. Frisch

2008-04-23T23:59:59.000Z

34

Meteorology: typical meteorological data for selected stations in Ghana  

Open Energy Info (EERE)

data for selected stations in Ghana data for selected stations in Ghana from NREL Dataset Summary Description (Abstract): Each TMY is a data set of hourly values of solar radiation and meteorological elements for a 1-year period. Solar radiation is modeled using the NREL METSTAT model, with surface observed cloud cover being the principal model input. The container file contains one TMY file for each selected station in the region, plus documentation files and a TMY data reader file for use with Microsoft Excel. (Purpose): Simulations> (Supplemental Information): A TMY consists of months selected from individual years and concatenated to form a complete year. The intended use is for computer simulations of solar energy conversion systems and building systems. Because of the selection criteria, these TMYs are not appropriate for simulations of wind energy conversion systems. A TMY provides a standard for hourly data for solar radiation and other meteorological elements that permit performance comparisons of system types and configurations for one or more locations. A TMY is not necessarily a good indicator of conditions over the next year, or even the next 5 years. Rather, it represents conditions judged to be typical over a long period of time, such as 30 years. Because they represent typical rather than extreme conditions, they are not suited for designing systems and their components to meet the worst-case conditions occurring at a location.

35

Meteorology: typical meteorological year data for selected stations in Sri  

Open Energy Info (EERE)

Sri Sri Lanka from NREL Dataset Summary Description (Abstract): A data set of hourly values of solar radiation and meteorological elements for a 1-year period. (Purpose): Simulations (Supplemental Information): A TMY consists of months selected from individual years and concatenated to form a complete year. The intended use is for computer simulations of solar energy conversion systems and building systems. Because of the selection criteria, these TMYs are not appropriate for simulations of wind energy conversion systems. A TMY provides a standard for hourly data for solar radiation and other meteorological elements that permit performance comparisons of system types and configurations for one or more locations. A TMY is not necessarily a good indicator of conditions over the next year, or even the next 5 years. Rather, it represents conditions judged to be typical over a long period of time, such as 30 years. Because they represent typical rather than extreme conditions, they are not suited for designing systems and their components to meet the worst-case conditions occurring at a location.

36

Meteorology: typical meteorological year data for selected stations in  

Open Energy Info (EERE)

Kenya from NREL Kenya from NREL Dataset Summary Description (Abstract): Each TMY is a data set of hourly values of solar radiation and meteorological elements for a 1-year period. Solar radiation is modeled using the NREL METSTAT model, with surface observed cloud cover being the principal model input. The container file contains one TMY file for each selected station in the region, plus documentation files and a TMY data reader file for use with Microsoft Excel. (Purpose): Simulations (Supplemental Information): A TMY consists of months selected from individual years and concatenated to form a complete year. The intended use is for computer simulations of solar energy conversion systems and building systems. Because of the selection criteria, these TMYs are not appropriate for simulations of wind energy conversion systems. A TMY provides a standard for hourly data for solar radiation and other meteorological elements that permit performance comparisons of system types and configurations for one or more locations. A TMY is not necessarily a good indicator of conditions over the next year, or even the next 5 years. Rather, it represents conditions judged to be typical over a long period of time, such as 30 years. Because they represent typical rather than extreme conditions, they are not suited for designing systems and their components to meet the worst-case conditions occurring at a location.

37

Meteorology: typical meteorological year data for selected stations in  

Open Energy Info (EERE)

Ethiopia from NREL Ethiopia from NREL Dataset Summary Description (Abstract): Each TMY is a data set of hourly values of solar radiation and meteorological elements for a 1-year period. Solar radiation is modeled using the NREL METSTAT model, with surface observed cloud cover being the principal model input. The container file contains one TMY file for each selected station in the region, plus documentation files and a TMY data reader file for use with Microsoft Excel. (Purpose): Simulations (Supplemental Information): A TMY consists of months selected from individual years and concatenated to form a complete year. The intended use is for computer simulations of solar energy conversion systems and building systems. Because of the selection criteria, these TMYs are not appropriate for simulations of wind energy conversion systems. A TMY provides a standard for hourly data for solar radiation and other meteorological elements that permit performance comparisons of system types and configurations for one or more locations. A TMY is not necessarily a good indicator of conditions over the next year, or even the next 5 years. Rather, it represents conditions judged to be typical over a long period of time, such as 30 years. Because they represent typical rather than extreme conditions, they are not suited for designing systems and their components to meet the worst-case conditions

38

Meteorology: typical meteorological year data for selected stations in  

Open Energy Info (EERE)

Brazil from NREL Brazil from NREL Dataset Summary Description (Abstract): Each TMY is a data set of hourly values of solar radiation and meteorological elements for a 1-year period. Solar radiation is modeled using the NREL METSTAT model, with surface observed cloud cover being the principal model input. The container file contains one TMY file for each selected station in the region, plus documentation files and a TMY data reader file for use with Microsoft Excel. (Purpose): Simulations (Supplemental Information): A TMY consists of months selected from individual years and concatenated to form a complete year. The intended use is for computer simulations of solar energy conversion systems and building systems. Because of the selection criteria, these TMYs are not appropriate for simulations of wind energy conversion systems. A TMY provides a standard for hourly data for solar radiation and other meteorological elements that permit performance comparisons of system types and configurations for one or more locations. A TMY is not necessarily a good indicator of conditions over the next year, or even the next 5 years. Rather, it represents conditions judged to be typical over a long period of time, such as 30 years. Because they represent typical rather than extreme conditions, they are not suited for designing systems and their components to meet the worst-case conditions occurring at a location.

39

Meteorology: typical meteorological year data for selected stations in  

Open Energy Info (EERE)

Nepal from NREL Nepal from NREL Dataset Summary Description (Abstract): Each TMY is a data set of hourly values of solar radiation and meteorological elements for a 1-year period. Solar radiation is modeled using the NREL METSTAT model, with surface observed cloud cover being the principal model input. The container file contains one TMY file for each selected station in the region, plus documentation files and a TMY data reader file for use with Microsoft Excel. (Purpose): Simulations (Supplemental Information): A TMY consists of months selected from individual years and concatenated to form a complete year. The intended use is for computer simulations of solar energy conversion systems and building systems. Because of the selection criteria, these TMYs are not appropriate for simulations of wind energy conversion systems. A TMY provides a standard for hourly data for solar radiation and other meteorological elements that permit performance comparisons of system types and configurations for one or more locations. A TMY is not necessarily a good indicator of conditions over the next year, or even the next 5 years. Rather, it represents conditions judged to be typical over a long period of time, such as 30 years. Because they represent typical rather than extreme conditions, they are not suited for designing systems and their components to meet the worst-case conditions occurring at a location.

40

Applications  

Science Conference Proceedings (OSTI)

Table 3   Wear-, erosion-, and corrosion-resistance applications of CVD...against neutron radiation

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

The Sun. A typical star in the solar neighborhood?  

E-Print Network (OSTI)

The Sun is used as the fundamental standard in chemical abundance studies, thus it is important to know whether the solar abundance pattern is representative of the solar neighborhood. Albeit at low precision (0.05 - 0.10 dex) the Sun seems to be a typical solar-metallicity disk star, at high precision (0.01 dex) its abundance pattern seems abnormal when compared to solar twins. The Sun shows a deficiency of refractory elements that could be due to the formation of terrestrial planets. The formation of giant planets may also introduce a signature in the chemical composition of stars. We discuss both planet signatures and also the enhancement of neutron-capture elements in the solar twin 18 Sco.

Melendez, Jorge

2013-01-01T23:59:59.000Z

42

Predicting aerodynamic characteristic of typical wind turbine airfoils using CFD  

DOE Green Energy (OSTI)

An investigation was conducted into the capabilities and accuracy of a representative computational fluid dynamics code to predict the flow field and aerodynamic characteristics of typical wind-turbine airfoils. Comparisons of the computed pressure and aerodynamic coefficients were made with wind tunnel data. This work highlights two areas in CFD that require further investigation and development in order to enable accurate numerical simulations of flow about current generation wind-turbine airfoils: transition prediction and turbulence modeling. The results show that the laminar-to turbulent transition point must be modeled correctly to get accurate simulations for attached flow. Calculations also show that the standard turbulence model used in most commercial CFD codes, the k-e model, is not appropriate at angles of attack with flow separation. 14 refs., 28 figs., 4 tabs.

Wolfe, W.P. [Sandia National Labs., Albuquerque, NM (United States); Ochs, S.S. [Iowa State Univ., Ames, IA (United States). Aerospace Engineering Dept.

1997-09-01T23:59:59.000Z

43

Security Implications of Typical Grid Computing Usage Scenarios  

SciTech Connect

A Computational Grid is a collection of heterogeneous computers and resources spread across multiple administrative domains with the intent of providing users uniform access to these resources. There are many ways to access the resources of a Computational Grid, each with unique security requirements and implications for both the resource user and the resource provider. A comprehensive set of Grid usage scenarios are presented and analyzed with regard to security requirements such as authentication, authorization, integrity, and confidentiality. The main value of these scenarios and the associated security discussions are to provide a library of situations against which an application designer can match, thereby facilitating security-aware application use and development from the initial stages of the application design and invocation. A broader goal of these scenarios are to increase the awareness of security issues in Grid Computing.

Humphrey, Marty; Thompson, Mary R.

2001-06-05T23:59:59.000Z

44

Nuclear reactor shield including magnesium oxide  

DOE Patents (OSTI)

An improvement in nuclear reactor shielding of a type used in reactor applications involving significant amounts of fast neutron flux, the reactor shielding including means providing structural support, neutron moderator material, neutron absorber material and other components as described below, wherein at least a portion of the neutron moderator material is magnesium in the form of magnesium oxide either alone or in combination with other moderator materials such as graphite and iron.

Rouse, Carl A. (Del Mar, CA); Simnad, Massoud T. (La Jolla, CA)

1981-01-01T23:59:59.000Z

45

Applications  

Science Conference Proceedings (OSTI)

Table 8   Major markets for ABS products...Market category Applications ABS grades Major appliances Refrigerator door and food liners; crisper pans;

46

Applications  

Science Conference Proceedings (OSTI)

Table 5   Selected applications for wrought aluminum alloys...vehicles, trucks and trailers 3105 Residential siding, mobile homes, rain-carrying goods,

47

Numerical simulations for a typical train fire in china  

Science Conference Proceedings (OSTI)

Railway is the key transport means in China including the Mainland, Taiwan, and Hong Kong. Consequent to so many big arson and accidental fires in the public transport systems including trains and buses, fire safety in passenger trains is a concern. ...

W. K. Chow; K. C. Lam; N. K. Fong; S. S. Li; Y. Gao

2011-01-01T23:59:59.000Z

48

Stocks of Total Crude Oil and Petroleum Products (Including SPR)  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Stocks include those ...

49

Representing and reasoning on typicality in formal ontologies  

Science Conference Proceedings (OSTI)

The problem of concept representation is relevant for many subfields of cognitive research, including psychology, philosophy and artificial intelligence. In particular, in recent years, it received great attention within knowledge representation, because ... Keywords: knowledge engineering, knowledge representation, ontologies, reasoning

Marcello Frixione; Antonio Lieto

2011-09-01T23:59:59.000Z

50

Appendix F Cultural Resources, Including  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Appendix F Appendix F Cultural Resources, Including Section 106 Consultation STATE OF CALIFORNIA - THE RESOURCES AGENCY EDMUND G. BROWN, JR., Governor OFFICE OF HISTORIC PRESERVATION DEPARTMENT OF PARKS AND RECREATION 1725 23 rd Street, Suite 100 SACRAMENTO, CA 95816-7100 (916) 445-7000 Fax: (916) 445-7053 calshpo@parks.ca.gov www.ohp.parks.ca.gov June 14, 2011 Reply in Reference To: DOE110407A Angela Colamaria Loan Programs Office Environmental Compliance Division Department of Energy 1000 Independence Ave SW, LP-10 Washington, DC 20585 Re: Topaz Solar Farm, San Luis Obispo County, California Dear Ms. Colamaria: Thank you for seeking my consultation regarding the above noted undertaking. Pursuant to 36 CFR Part 800 (as amended 8-05-04) regulations implementing Section

51

Superabrasive Applications  

Science Conference Proceedings (OSTI)

Table 2   Typical applications of superabrasives...airports, highways Mining products Stone, shale, rock Drilling Precision grinding wheels Carbide Tool production and resharpening; wear parts and

52

Countries Gasoline Prices Including Taxes  

Gasoline and Diesel Fuel Update (EIA)

Countries (U.S. dollars per gallon, including taxes) Countries (U.S. dollars per gallon, including taxes) Date Belgium France Germany Italy Netherlands UK US 01/13/14 7.83 7.76 7.90 8.91 8.76 8.11 3.68 01/06/14 8.00 7.78 7.94 8.92 8.74 8.09 3.69 12/30/13 NA NA NA NA NA NA 3.68 12/23/13 NA NA NA NA NA NA 3.63 12/16/13 7.86 7.79 8.05 9.00 8.78 8.08 3.61 12/9/13 7.95 7.81 8.14 8.99 8.80 8.12 3.63 12/2/13 7.91 7.68 8.07 8.85 8.68 8.08 3.64 11/25/13 7.69 7.61 8.07 8.77 8.63 7.97 3.65 11/18/13 7.99 7.54 8.00 8.70 8.57 7.92 3.57 11/11/13 7.63 7.44 7.79 8.63 8.46 7.85 3.55 11/4/13 7.70 7.51 7.98 8.70 8.59 7.86 3.61 10/28/13 8.02 7.74 8.08 8.96 8.79 8.04 3.64 10/21/13 7.91 7.71 8.11 8.94 8.80 8.05 3.70 10/14/13 7.88 7.62 8.05 8.87 8.74 7.97 3.69

53

Applications  

Science Conference Proceedings (OSTI)

Table 2   Applications for titanium and titanium alloys...for FGD units, nuclear waste disposal Geothermal energy Heat exchangers, evaporators, condensers, tubes Marine engineering Shipbuilding Heat exchangers, condensers, piping

54

Applications  

Science Conference Proceedings (OSTI)

Table 2   Examples of applications and parts made with vacuum infusion...small aircraft Industrial Fan blades, part for fish counting unit, toilet bowl, oil

55

Applications  

Science Conference Proceedings (OSTI)

Table 6 Selected applications for aluminum casting alloys...gears; jet engine compressor cases 356.0 Sand: flywheel castings; automotive transmission cases; oil pans; pump bodies. Permanent: machine tool parts;

56

Applications  

Science Conference Proceedings (OSTI)

Table 1   Application of sintered stainless steels...316L Photographic equipment 316L Cam cleats 304L Dishwasher components 304L Can opener gears 410L...

57

Applications:  

NLE Websites -- All DOE Office Websites (Extended Search)

Applications: Applications: ● Telecommunications: cell / smartphone; multi-party secure phone calls; videoconferencing; Voice over IP (VoIP) ● Banking and financial transactions: ATM, debit / credit card and e-Commerce ● e-Business; e-gaming; e-books; e-music; e-movies; e-gambling ● Wireless internet ● Electronic voting ● Facility and vehicle access ● Information exchange for government/defense

58

Applications  

Science Conference Proceedings (OSTI)

...Another rapidly growing market segment is the wind power generation group of components including bearings, tower connector flanges, and electrical generator parts....

59

Assessment of speciation techniques including the application of photoacoustic spectroscopy  

Science Conference Proceedings (OSTI)

This document describes laboratory experiments that compare chromatographic and spectroscopic methods for rapidly characterizing ionic species in detail. These techniques were tested on various radioactive ion systems to develop a rapid, accurate approach to site characterization for use with Remedial Action Programs. Promising techniques were evaluated. 9 refs., 16 figs., 2 tabs.

Bucher, J.; Gehmecker, H.; Edelstein, N.

1985-08-01T23:59:59.000Z

60

Applications  

Science Conference Proceedings (OSTI)

Table 3   Major application areas of porous P/M materials...refining Semiconductor Particle removal process gas Bulk gas delivery systems Purifier media retainers Analysis instruments Gas/liquid chromatography Gas sampling Sensor protection Chemical processing Catalyst recovery Process gases and liquids Fluid-bed reactor products Mineral processing Coal,...

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Applications  

Science Conference Proceedings (OSTI)

Table 3   Some applications of investment casting...Electrical equipment Electronics, radar Guns and small armaments Hand tools Jewelry Machine tools Materials handling equipment Metal working equipment Oil well drilling and auxiliary equipment Optical equipment Packaging equipment Pneumatic and hydraulic systems Prosthetic appliances Pumps Sports gear...

62

Applications  

Science Conference Proceedings (OSTI)

Table 1   Commercial applications of refractory metals and alloys by industry...Rhenium, W-Re Process industries Heating and cooling coils Tantalum, Ta-Nb Shell and tube heat exchangers Tantalum Condensers Tantalum Tantalum-clad steel vessels Tantalum Distillation towers Tantalum Valves for hot sulfuric acid service Molybdenum, tantalum, Ta-Nb Expansion joints (bellows) Tantalum...

63

Applications  

Science Conference Proceedings (OSTI)

Table 9   Applications of various polymers...bins 767 aircraft acoustical tile 767 and other Boeing aircraft brackets Airbus A320 bulk cargo floor sandwich structural panels Airbus A330-340 lower wing fairings A3XX main stair case (developmental) Beluga heavy-duty entrance floor panels Dornier 328 landing flap ribs Dornier 328 ice protection...

64

Learning Outcomes Department of Chemistry and Biochemistry: Biochemistry Major (typical electives)  

E-Print Network (OSTI)

foundations in the fundamentals and applications of current chemical theories for the physical world. B. Use graphing 100A 105A Characterize reaction kinetics in a laboratory 100A 105A Measure chemical equilibria the factors affecting the rate of a chemical reaction, including temperature. Analyze kinetic data

Gleeson, Joseph G.

65

Radiation Shielding Applications  

NLE Websites -- All DOE Office Websites (Extended Search)

Shielding Radiation Shielding Applications Heavy concrete is standard concrete in which conventional aggregate (typically gravel) is replaced with aggregate composed of a dense...

66

Applications of Zinc  

Science Conference Proceedings (OSTI)

Table 1   Typical applications of zinc-coated steel products...galvanized Various alloys Structural steel for power generating plants, petrochemical

67

Industrial and Commercial Heat Pump Applications in the United States  

E-Print Network (OSTI)

The energy crisis of 1973 accelerated the development of large-scale heat pumps in the United States. Since that time, the commercial, institutional, and industrial applications of heat pumps for waste heat recovery have expanded. This paper reviews the trends in heat pump cycle developments and discusses both the closed vapor compression cycle and refrigerants most commonly used and the open-cycle mechanical vapor compression heat pumps. Waste heat sources, heat loads served by heat pumps--and typical applications using heat pumps for large-scale space heating, domestic water heating, and industrial process water heating-- are discussed. Typical installations include commercial applications in hotels, high-rise apartments and condominiums, and office buildings. Institutional installations discussed include hospitals, universities, wastewater treatment plants, and airport terminals. Industrial applications largely center on food processing industries, feedwater heating, metal fabricating, and other industries. Reference is also made to other applications and alternative energy sources now gaining acceptance, including groundwater/geothermal water.

Niess, R. C.

1986-06-01T23:59:59.000Z

68

Top-k typicality queries and efficient query answering methods on large databases  

Science Conference Proceedings (OSTI)

Finding typical instances is an effective approach to understand and analyze large data sets. In this paper, we apply the idea of typicality analysis from psychology and cognitive science to database query answering, and study the novel problem of answering ... Keywords: Efficient query answering, Top-k query, Typicality analysis

Ming Hua; Jian Pei; Ada W. Fu; Xuemin Lin; Ho-Fung Leung

2009-06-01T23:59:59.000Z

69

Science Accelerator content now includes multimedia  

Office of Scientific and Technical Information (OSTI)

Science Accelerator content now includes multimedia Science Accelerator has expanded its suite of collections to include ScienceCinema, which contains videos produced by the U.S....

70

A study of the effects of well and fracture design in a typical Marcellus shale well.  

E-Print Network (OSTI)

??The problem with typical Marcellus shale wells is the lack of information that has beenaccumulated and the amount of information that is commercially available to (more)

Schweitzer, Ross T.

2009-01-01T23:59:59.000Z

71

Petroleum Gasoline & Distillate Needs Including the Energy ...  

U.S. Energy Information Administration (EIA)

Home > Petroleum > Analysis > Petroleum Gasoline & Distillate Needs Including the Energy Independence and Security Act (EISA) ...

72

Petroleum Gasoline & Distillate Needs Including the Energy ...  

U.S. Energy Information Administration (EIA)

Petroleum Gasoline & Distillate Needs Including the Energy Independence and Security Act (EISA) Impacts

73

Impact of Alternative Energy Prices, Tenure Arrangements and Irrigation Technologies on a Typical Texas High Plains Farm  

E-Print Network (OSTI)

Irrigation is a major contributing factor in crop production on the Texas High Plains. It is responsible for greatly increasing crop production and farm income for the region. Two factors, a declining groundwater supply and increasing production costs, are of primary concern because they impact on farm operations and producer economic viability. A recursive linear programming model for a typical Texas High Plains irrigated farm was developed to evaluate expected impact of price changes, tenure and new technology. The model includes a Fortran sub-routine that adjusts irrigation factors each year based on the linear programming solution of the previous year. After calculating new pumping energy requirements, well yield, and pumping lift, the Fortran component updates the linear programming model. This procedure continues automatically to the end of a specified planning period or to economic exhaustion of the groundwater, whichever occurs first. Static applications of the model, in a deep water situation, showed that a natural gas price increase from $1.50 to $2.20 per thousand cubic feet (mcf) would result in reductions in irrigation levels. Irrigation was terminated when the price of natural gas reached about $7.00 per mcf. In a shallow water situation, much higher natural gas prices were reached ($3.60 per mcf) before short-run adjustments in farm organization began to occur. Under furrow irrigation, irrigation was terminated when the natural gas price reached $7.00 per mcf. Increased natural gas prices impact heavily on returns above variable costs (up to 15 percent reductions) for a 60 percent natural gas price increase. The effects of rising natural gas prices over a longer period of time were more significant. Annual returns (above variable and fixed costs) were reduced by as much as 30 percent, and the present value of returns to water was reduced by as much as 80 percent as the natural gas price was increased annually by $0.25 per mcf (from $1.50 per mcf). The economic life of deep groundwater was shortened by as much as 18 years. Renter-operators are even more vulnerable to rising natural gas prices than are owner-operators. With rising natural gas prices, profitability over time for the renter is low. As natural gas prices continue to increase, the greater will be the incentives for renter-operators to seek more favorable rental terms such as a sharing of irrigation costs. With the problem of a declining groundwater supply and rising natural gas prices, an economic incentive exists for producers to find new technologies that will enable them to make more efficient use of remaining groundwater and of natural gas. Substantial economic gains appear feasible through improved pump efficiency. Increasing pump efficiency from 50 to 75 percent will not increase the economic life of the water supply, but can improve farm profits over time; e.g., the present value of groundwater was increased 33 percent for a typical farm with an aquifer containing 250 feet of saturated thickness and 15 percent for 75 feet of saturated thickness. Improved irrigation distribution systems can help conserve water and reduce irrigation costs. Results indicate that irrigation can be extended by 11 or more years with 50 percent improved distribution efficiency. In addition, the increase in present value of groundwater on the 1.69 million irrigated acres of the Texas High Plains was estimated to be $995 million with 50 percent improved efficiency. Limitations in borrowing can substantially reduce annual net returns. This analysis suggests that the farmer can economically justify very high costs of borrowing rather than a limitation of funds available for operating expenses.

Petty, J. A.; Lacewell, R. D.; Hardin, D. C.; Whitson, R. E.

1980-05-01T23:59:59.000Z

74

Major initiatives in materials research at Western include  

E-Print Network (OSTI)

in nuclear reactors; and a third in Engineering- J. Jiang, supported by UNENE, working on control in the theory of condensed matter, including its applications to polymers, optical, electronic, and magnetic NSERC Industrial Research Chairs who together make Western a leading university in nuclear power

Christensen, Dan

75

Electrochemical system including lamella settler crystallizer  

DOE Patents (OSTI)

A crystallizer which incorporates a lamella settler and which is particularly applicable for use in batteries and power cells for electric vehicles or stationary applications. The lamella settler can be utilized for coarse particle separation or for agglomeration, and is particularly applicable to aluminum-air batteries or power cells for solving the hydrargillite (aluminum-hydroxide) removal problems from such batteries. This invention provides the advantages of very low energy consumption, turbulence, shear, cost and maintenance. Thus, due to the low shear and low turbulence of this invention, it is particularly effective in the control of aluminum hydroxide particle size distribution in the various sections of an aluminum-air system, as will as in other elecrochemical systems requiring separation for phases of different densities.

Maimoni, Arturo (Orinda, CA)

1988-01-01T23:59:59.000Z

76

Guide to natural gas cogeneration. [Glossary included  

SciTech Connect

Guide to natural gas cogeneration is the most extensive reference ever written on the engineering and economic aspects of gas fired cogeneration systems. Forty-one chapters cover equipment considerations and applications for gas engines, gas turbines, stem engines, electrical switchgear, and packaged systems. The text is thoroughly illustrated with case studies for both commercial and industrial applications of all sizes, as well as for packaged systems for restaurants and hospitals. A special chapter illustrates market opportunities and keys to successful development. Separate abstracts of most chapters and several appendices have been prepared.

Hay, N.E. (ed.)

1988-01-01T23:59:59.000Z

77

To Look or Not to Look? Typical and Atypical Development of Oculomotor Control  

Science Conference Proceedings (OSTI)

The ability to inhibit saccades toward suddenly appearing peripheral stimuli (prosaccades) and direct them to contralateral locations instead (antisaccades) is a crucial marker of eye movement control. Typically developing infants as young as 4-month-olds ...

Gaia Scerif; Annette Karmiloff-smith; Ruth Campos; Mayada Elsabbagh; Jon Driver; Kim Cornish

2005-04-01T23:59:59.000Z

78

cDNA encoding a polypeptide including a hevein sequence  

DOE Patents (OSTI)

A cDNA clone (HEV1) encoding hevein was isolated via polymerase chain reaction (PCR) using mixed oligonucleotides corresponding to two regions of hevein as primers and a Hevea brasiliensis latex cDNA library as a template. HEV1 is 1018 nucleotides long and includes an open reading frame of 204 amino acids. The deduced amino acid sequence contains a pu GOVERNMENT RIGHTS This application was funded under Department of Energy Contract DE-AC02-76ER01338. The U.S. Government has certain rights under this application and any patent issuing thereon.

Raikhel, Natasha V. (Okemos, MI); Broekaert, Willem F. (Dilbeek, BE); Chua, Nam-Hai (Scarsdale, NY); Kush, Anil (New York, NY)

1993-02-16T23:59:59.000Z

79

Gas storage materials, including hydrogen storage materials  

DOE Patents (OSTI)

A material for the storage and release of gases comprises a plurality of hollow elements, each hollow element comprising a porous wall enclosing an interior cavity, the interior cavity including structures of a solid-state storage material. In particular examples, the storage material is a hydrogen storage material such as a solid state hydride. An improved method for forming such materials includes the solution diffusion of a storage material solution through a porous wall of a hollow element into an interior cavity.

Mohtadi, Rana F; Wicks, George G; Heung, Leung K; Nakamura, Kenji

2013-02-19T23:59:59.000Z

80

Intentionally Including - Engaging Minorities in Physics Careers |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Intentionally Including - Engaging Minorities in Physics Careers Intentionally Including - Engaging Minorities in Physics Careers Intentionally Including - Engaging Minorities in Physics Careers April 24, 2013 - 4:37pm Addthis Joining Director Dot Harris (second from left) were Marlene Kaplan, the Deputy Director of Education and director of EPP, National Oceanic and Atmospheric Administration, Claudia Rankins, a Program Officer with the National Science Foundation and Jim Stith, the past Vice-President of the American Institute of Physics Resources. Joining Director Dot Harris (second from left) were Marlene Kaplan, the Deputy Director of Education and director of EPP, National Oceanic and Atmospheric Administration, Claudia Rankins, a Program Officer with the National Science Foundation and Jim Stith, the past Vice-President of the

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Transmission line including support means with barriers  

DOE Patents (OSTI)

A gas insulated transmission line includes an elongated outer sheath, a plurality of inner conductors disposed within and extending along the outer sheath, and an insulating gas which electrically insulates the inner conductors from the outer sheath. A support insulator insulatably supports the inner conductors within the outer sheath, with the support insulator comprising a main body portion including a plurality of legs extending to the outer sheath, and barrier portions which extend between the legs. The barrier portions have openings therein adjacent the main body portion through which the inner conductors extend.

Cookson, Alan H. (Pittsburgh, PA)

1982-01-01T23:59:59.000Z

82

Photo of the Week: Not Your Typical Jet Engine | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Not Your Typical Jet Engine Not Your Typical Jet Engine Photo of the Week: Not Your Typical Jet Engine November 23, 2012 - 11:57am Addthis As part of the Aircraft Nuclear Propulsion Program, the U.S. conducted extensive research showing that nuclear fission could power an aircraft. The research involved a series of Heat Transfer Reactor Experiments (HTREs), which tested if different types of jet engines could be run by nuclear power. In 1955, however, the project was cancelled, and a safe, operational prototype aircraft was never developed. In this 1988 photo, the two HTRE reactors are shown in transport to Idaho National Laboratory's EBR-1 visitor center, where they remain today. | Photo courtesy of Idaho National Laboratory. As part of the Aircraft Nuclear Propulsion Program, the U.S. conducted

83

DISASTER POLICY Including Extreme Emergent Situations (EES)  

E-Print Network (OSTI)

on the ACGME website with information relating to the ACGME response to the disaster. 3. The University-specific Program Requirements. Defined Responsibilities Following the Declaration of a Disaster or Extreme EmergentPage 123 DISASTER POLICY Including Extreme Emergent Situations (EES) The University of Connecticut

Oliver, Douglas L.

84

Buildings Included on EMS Reports"  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Office of Legacy Management Office of Legacy Management Buildings Included on EMS Reports" "Site","Property Name","Property ID","GSF","Incl. in Water Baseline (CY2007)","Water Baseline (sq. ft.)","Water CY2008 (sq. ft.)","Water CY2009 (sq. ft.)","Water Notes","Incl. in Energy Baseline (CY2003)","Energy Baseline (sq. ft.)","CY2008 Energy (sq. ft.)","CY2009 Energy (sq. ft.)","Energy Notes","Included as Existing Building","CY2008 Existing Building (sq. ft.)","Reason for Building Exclusion" "Column Totals",,"Totals",115139,,10579,10579,22512,,,3183365,26374,115374,,,99476 "Durango, CO, Disposal/Processing Site","STORAGE SHED","DUD-BLDG-STORSHED",100,"no",,,,,"no",,,,"OSF","no",,"Less than 5,000 GSF"

85

Power generation method including membrane separation  

SciTech Connect

A method for generating electric power, such as at, or close to, natural gas fields. The method includes conditioning natural gas containing C.sub.3+ hydrocarbons and/or acid gas by means of a membrane separation step. This step creates a leaner, sweeter, drier gas, which is then used as combustion fuel to run a turbine, which is in turn used for power generation.

Lokhandwala, Kaaeid A. (Union City, CA)

2000-01-01T23:59:59.000Z

86

Electric power monthly, September 1990. [Glossary included  

SciTech Connect

The purpose of this report is to provide energy decision makers with accurate and timely information that may be used in forming various perspectives on electric issues. The power plants considered include coal, petroleum, natural gas, hydroelectric, and nuclear power plants. Data are presented for power generation, fuel consumption, fuel receipts and cost, sales of electricity, and unusual occurrences at power plants. Data are compared at the national, Census division, and state levels. 4 figs., 52 tabs. (CK)

1990-12-17T23:59:59.000Z

87

BS in General Science, with various specializations possible Typical Program of Study1 4 year  

E-Print Network (OSTI)

BS in General Science, with various specializations possible Typical Program of Study1 ­ 4 year Fall Quarter Winter Quarter Spring Quarter Freshman Science (5) Science (5) Science (5) Math (5) Math (5) Core (5) Core (5)2 Core (5) Core (5) Sophomore Science (5) Science (5) Science (5) Science (5

Carter, John

88

A single TLD dose algorithm to satisfy federal standards and typical field conditions  

Science Conference Proceedings (OSTI)

Modern whole-body dosimeters are often required to accurately measure the absorbed dose in a wide range of radiation fields. While programs are commonly developed around the fields tested as part of the National Voluntary Accreditation Program (NVLAP), the actual fields of application may be significantly different. Dose algorithms designed to meet the NVLAP standard, which emphasizes photons and high-energy beta radiation, may not be capable of the beta-energy discrimination necessary for accurate assessment of absorbed dose in the work environment. To address this problem, some processors use one algorithm for NVLAP testing and one or more different algorithms for the work environments. After several years of experience with a multiple algorithm approach, the Dosimetry Services Group of Yankee Atomic Electric Company (YAEC) developed a one-algorithm system for use with a four-element TLD badge using Li2B4O7 and CaSO4 phosphors. The design of the dosimeter allows the measurement of the effective energies of both photon and beta components of the radiation field, resulting in excellent mixed-field capability. The algorithm was successfully tested in all of the NVLAP photon and beta fields, as well as several non-NVLAP fields representative of the work environment. The work environment fields, including low- and medium-energy beta radiation and mixed fields of low-energy photons and beta particles, are often more demanding than the NVLAP fields. This paper discusses the development of the algorithm as well as some results of the system testing including: mixed-field irradiations, angular response, and a unique test to demonstrate the stability of the algorithm. An analysis of the uncertainty of the reported doses under various irradiation conditions is also presented.

Stanford, N.; McCurdy, D.E. (Yankee Atomic Electric Company, Bolton, MA (USA))

1990-06-01T23:59:59.000Z

89

Addressing questions about including environmental effects in the DMSO HLA  

SciTech Connect

The Defense Modeling and Simulation Office (DMSO) is developing a High Level Architecture (HLA) to support the DOD Modeling and Simulation (M and S) community. Many, if not all, of the simulations involve the environment in some fashion. In some applications, the simulation takes place in an acknowledged environment without any environmental functionality being taken into account. The Joint Training Federation Prototype (JTFp) is one of several prototype efforts that have been created to provide a test of the DMSO HLA. In addition to addressing the applicability of the HLA to a training community, the JTFp is also one of two prototype efforts that is explicitly including environmental effects in their simulation effort. These two prototyping efforts are examining the issues associated with the inclusion of the environment in an HLA federation. In deciding whether or not to include an environmental federation in the JTFp effort, a number of questions have been raised about the environment and the HLA. These questions have raised the issue of incompatibility between the environment and the HLA and also shown that there is something unique about including the environment in simulations. The purpose of this White Paper, which was developed with inputs from the National Air and Space [Warfare] Model Program among others, is to address the various questions that have been posed about including environmental effects in an HLA simulation.

Hummel, J.R.

1996-10-01T23:59:59.000Z

90

Stocks of Crude Oil (Including SPR) - U.S. Energy Information ...  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Stocks include those ...

91

Thermovoltaic semiconductor device including a plasma filter  

DOE Patents (OSTI)

A thermovoltaic energy conversion device and related method for converting thermal energy into an electrical potential. An interference filter is provided on a semiconductor thermovoltaic cell to pre-filter black body radiation. The semiconductor thermovoltaic cell includes a P/N junction supported on a substrate which converts incident thermal energy below the semiconductor junction band gap into electrical potential. The semiconductor substrate is doped to provide a plasma filter which reflects back energy having a wavelength which is above the band gap and which is ineffectively filtered by the interference filter, through the P/N junction to the source of radiation thereby avoiding parasitic absorption of the unusable portion of the thermal radiation energy.

Baldasaro, Paul F. (Clifton Park, NY)

1999-01-01T23:59:59.000Z

92

Commercial Building Profiles

This dataset includes simulation...  

Open Energy Info (EERE)

number in public use datasets. Three modeling scenarios are available: existing stock (with 2003 historical weather), stock as if rebuilt new (with typical weather), and...

93

The Particle Adventure | How do we interpret our data? | Typical detector  

NLE Websites -- All DOE Office Websites (Extended Search)

Typical detector components Typical detector components The reason that detectors are divided into many components is that each component tests for a special set of particle properties. These components are stacked so that all particles will go through the different layers sequentially. A particle will not be evident until it either interacts with the detector in a measurable fashion, or decays into detectable particles. The interaction of various particles with the different components of a detector: *Neutrinos are not shown on this chart because they rarely interact with matter, and can only be detected by missing matter and energy. Just so you know, the pion ( ) is a charged meson.* A few important things to note: Charged particles, like electrons and protons, are detected both in the tracking chamber and the electromagnetic calorimeter.

94

Models of Procyon A including seismic constraints  

E-Print Network (OSTI)

Detailed models of Procyon A based on new asteroseismic measurements by Eggenberger et al (2004) have been computed using the Geneva evolution code including shellular rotation and atomic diffusion. By combining all non-asteroseismic observables now available for Procyon A with these seismological data, we find that the observed mean large spacing of 55.5 +- 0.5 uHz favours a mass of 1.497 M_sol for Procyon A. We also determine the following global parameters of Procyon A: an age of t=1.72 +- 0.30 Gyr, an initial helium mass fraction Y_i=0.290 +- 0.010, a nearly solar initial metallicity (Z/X)_i=0.0234 +- 0.0015 and a mixing-length parameter alpha=1.75 +- 0.40. Moreover, we show that the effects of rotation on the inner structure of the star may be revealed by asteroseismic observations if frequencies can be determined with a high precision. Existing seismological data of Procyon A are unfortunately not accurate enough to really test these differences in the input physics of our models.

P. Eggenberger; F. Carrier; F. Bouchy

2005-01-14T23:59:59.000Z

95

Electra-optical device including a nitrogen containing electrolyte  

DOE Patents (OSTI)

Described is a thin-film battery, especially a thin-film microbattery, and a method for making same having application as a backup or primary integrated power source for electronic devices. The battery includes a novel electrolyte which is electrochemically stable and does not react with the lithium anode and a novel vanadium oxide cathode. Configured as a microbattery, the battery can be fabricated directly onto a semiconductor chip, onto the semiconductor die or onto any portion of the chip carrier. The battery can be fabricated to any specified size or shape to meet the requirements of a particular application. The battery is fabricated of solid state materials and is capable of operation between {minus}15 C and 150 C.

Bates, J.B.; Dudney, N.J.; Gruzalski, G.R.; Luck, C.F.

1995-10-03T23:59:59.000Z

96

Electra-optical device including a nitrogen containing electrolyte  

SciTech Connect

Described is a thin-film battery, especially a thin-film microbattery, and a method for making same having application as a backup or primary integrated power source for electronic devices. The battery includes a novel electrolyte which is electrochemically stable and does not react with the lithium anode and a novel vanadium oxide cathode Configured as a microbattery, the battery can be fabricated directly onto a semiconductor chip, onto the semiconductor die or onto any portion of the chip carrier. The battery can be fabricated to any specified size or shape to meet the requirements of a particular application. The battery is fabricated of solid state materials and is capable of operation between -15.degree. C. and 150.degree. C.

Bates, John B. (Oak Ridge, TN); Dudney, Nancy J. (Knoxville, TN); Gruzalski, Greg R. (Oak Ridge, TN); Luck, Christopher F. (Knoxville, TN)

1995-01-01T23:59:59.000Z

97

Evaluation of the typical meteorological years for solar heating and cooling system studies. Final report  

DOE Green Energy (OSTI)

This report is a summary of an evaluation of the weather data set, generated at Sandia Laboratories, known as the Typical Meteorological Year (TMY) Data. The purpose of the evaluation is to determine how well the TMY data represent actual long-term weather data in affecting the performance of solar heating and cooling systems. The two data sets are compared through detailed SHAC simulation.

Freeman, T. L.

1979-12-01T23:59:59.000Z

98

Estimating solar access of typical residential rooftops: A case study in San Jose, CA  

E-Print Network (OSTI)

the 14 th European Photovoltaic Solar Energy Conference androoftop solar-energy systems, including photovoltaic panelsrooftop solar-energy systems, including photovoltaic panels

Levinson, Ronnen M

2008-01-01T23:59:59.000Z

99

Designers of embedded processors have typically optimized for low power con-  

E-Print Network (OSTI)

those of vector architectures for supercomputing. The vector state includes a vector register file (VRF

Kozyrakis, Christos

100

IMS applications analysis  

SciTech Connect

This report examines the market potential of a miniature, hand-held Ion Mobility Spectrometer. Military and civilian markets are discussed, as well as applications in a variety of diverse fields. The strengths and weaknesses of competing technologies are discussed. An extensive Ion Mobility Spectrometry (IMS) bibliography is included. The conclusions drawn from this study are: (1) There are a number of competing technologies that are capable of detecting explosives, drugs, biological, or chemical agents. The IMS system currently represents the best available compromise regarding sensitivity, specificity, and portability. (2) The military market is not as large as the commercial market, but the military services are more likely to invest R and D funds in the system. (3) Military applications should be addressed before commercial applications are addressed. (4) There is potentially a large commercial market for rugged, hand-held Ion Mobility Spectrometer systems. Commercial users typically do not invest R and D funds in this type of equipment rather, they wait for off-the-shelf availability.

RODACY,PHILIP J.; REBER,STEPHEN D.; SIMONSON,ROBERT J.; HANCE,BRADLEY G.

2000-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

LANL application communication patterns  

SciTech Connect

This brief presentation describes the communication patterns used by a set of unclassified applications developed at Los Alamos National Laboratory: XNobel/XRAGE/RAGE/SAGE, Krak, Sweep3D, and Partisn. It mentions which processes communicate with which other processes, whether the application is typically run in a strong-scaling mode or a weak-scaling mode, what message sizes are commonly used, and how the application's performance changes at scale.

Pakiin, Scott [Los Alamos National Laboratory

2011-01-10T23:59:59.000Z

102

Process Applications  

Science Conference Proceedings (OSTI)

...flash-welding applications include: Chain links Transmission bands Automotive flywheel ring gears Strips that are joined for continuous processing lines Wire and bar drawing operations for continuous stamping press

103

Water is used for many purposes, includ-ing growing crops, producing copper,  

E-Print Network (OSTI)

WATER USES Water is used for many purposes, includ- ing growing crops, producing copper, generating electricity, watering lawns, keeping clean, drinking and recreation. Bal- ancing the water budget comes down of the water budget. Reducing demand involves re- ducing how much water each person uses, lim- iting the number

104

Typical Consultants/Vendors used by EOTA for Subject Matter Expert and  

NLE Websites -- All DOE Office Websites (Extended Search)

Consultants/Vendors used by EOTA for Subject Matter Expert and Consultants/Vendors used by EOTA for Subject Matter Expert and operatioal support Typical Consultants/Vendors used by EOTA for Subject Matter Expert and operatioal support Vendor's Name Contact/Rep Address Work Phone 615 Music Productions, Inc. Steve Hayes or Laura Palmer 1030 16th Ave. South, Nashville, TN 37212 616-244-6515 Adams, James F. James Adams 1217 Brookshire Dr., Bedford, TX 76021 214-674-6868 Adobe Systems Inc. N/A 2750 Barrett Lakes Blvd., Kennesaw, GA 30144 800-833-6687 Atlantech Resellers Inc, DBA CablesAndKits.com Craig Haynie 4555 Atwater Ct Ste ! Buford, GA 21075 877-633-2629 Albuquerque Printing Co Albert Padilla 3838 Bogan Ave.NE, Albq. 87109 505-872-2200 AlphaTRAC, Inc. John Ciolek 8670 Wolff Ct Ste 120 Westminster, CO 80031 303-428-5670 Amazon.com CSR

105

Hydraulically actuated fuel injector including a pilot operated spool valve assembly and hydraulic system using same  

DOE Patents (OSTI)

The present invention relates to hydraulic systems including hydraulically actuated fuel injectors that have a pilot operated spool valve assembly. One class of hydraulically actuated fuel injectors includes a solenoid driven pilot valve that controls the initiation of the injection event. However, during cold start conditions, hydraulic fluid, typically engine lubricating oil, is particularly viscous and is often difficult to displace through the relatively small drain path that is defined past the pilot valve member. Because the spool valve typically responds slower than expected during cold start due to the difficulty in displacing the relatively viscous oil, accurate start of injection timing can be difficult to achieve. There also exists a greater difficulty in reaching the higher end of the cold operating speed range. Therefore, the present invention utilizes a fluid evacuation valve to aid in displacement of the relatively viscous oil during cold start conditions.

Shafer, Scott F. (Morton, IL)

2002-01-01T23:59:59.000Z

106

Office of Legacy Management Buildings Included on EMS Reports...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Office of Legacy Management Buildings Included on EMS Reports Office of Legacy Management Buildings Included on EMS Reports Office of Legacy Management Buildings Included on EMS...

107

Passive gust load alleviation through bend-twist coupling of composite beams on typical commercial airplane wings  

E-Print Network (OSTI)

The effects of bend-twist coupling on typical commercial airplane wings are evaluated. An analytical formulation of the orthotropic box beam bending stiffness matrix is derived by combining Euler-Bernoulli beam theory and ...

Gauthier Perron, Sbastien

2012-01-01T23:59:59.000Z

108

cDNA encoding a polypeptide including a hevein sequence  

DOE Patents (OSTI)

A cDNA clone (HEV1) encoding hevein was isolated via polymerase chain reaction (PCR) using mixed oligonucleotides corresponding to two regions of hevein as primers and a Hevea brasiliensis latex cDNA library as a template. HEV1 is 1018 nucleotides long and includes an open reading frame of 204 amino acids. The deduced amino acid sequence contains a putative signal sequence of 17 amino acid residues followed by a 187 amino acid polypeptide. The amino-terminal region (43 amino acids) is identical to hevein and shows homology to several chitin-binding proteins and to the amino-termini of wound-induced genes in potato and poplar. The carboxyl-terminal portion of the polypeptide (144 amino acids) is 74--79% homologous to the carboxyl-terminal region of wound-inducible genes of potato. Wounding, as well as application of the plant hormones abscisic acid and ethylene, resulted in accumulation of hevein transcripts in leaves, stems and latex, but not in roots, as shown by using the cDNA as a probe. A fusion protein was produced in E. coli from the protein of the present invention and maltose binding protein produced by the E. coli. 12 figs.

Raikhel, N.V.; Broekaert, W.F.; Chua, N.H.; Kush, A.

1999-05-04T23:59:59.000Z

109

CDNA encoding a polypeptide including a hevein sequence  

DOE Patents (OSTI)

A cDNA clone (HEV1) encoding hevein was isolated via polymerase chain reaction (PCR) using mixed oligonucleotides corresponding to two regions of hevein as primers and a Hevea brasiliensis latex cDNA library as a template. HEV1 is 1018 nucleotides long and includes an open reading frame of 204 amino acids. The deduced amino acid sequence contains a putative signal sequence of 17 amino acid residues followed by a 187 amino acid polypeptide. The amino-terminal region (43 amino acids) is identical to hevein and shows homology to several chitin-binding proteins and to the amino-termini of wound-induced genes in potato and poplar. The carboxyl-terminal portion of the polypeptide (144 amino acids) is 74-79% homologous to the carboxyl-terminal region of wound-inducible genes of potato. Wounding, as well as application of the plant hormones abscisic acid and ethylene, resulted in accumulation of hevein transcripts in leaves, stems and latex, but not in roots, as shown by using the cDNA as a probe. A fusion protein was produced in E. coli from the protein of the present invention and maltose binding protein produced by the E. coli.

Raikhel, Natasha V. (Okemos, MI); Broekaert, Willem F. (Dilbeek, BE); Chua, Nam-Hai (Scarsdale, NY); Kush, Anil (New York, NY)

1995-03-21T23:59:59.000Z

110

cDNA encoding a polypeptide including a hevein sequence  

DOE Patents (OSTI)

A cDNA clone (HEV1) encoding hevein was isolated via polymerase chain reaction (PCR) using mixed oligonucleotides corresponding to two regions of hevein as primers and a Hevea brasiliensis latex cDNA library as a template. HEV1 is 1018 nucleotides long and includes an open reading frame of 204 amino acids. The deduced amino acid sequence contains a putative signal sequence of 17 amino acid residues followed by a 187 amino acid polypeptide. The amino-terminal region (43 amino acids) is identical to hevein and shows homology to several chitin-binding proteins and to the amino-termini of wound-induced genes in potato and poplar. The carboxyl-terminal portion of the polypeptide (144 amino acids) is 74-79% homologous to the carboxyl-terminal region of wound-inducible genes of potato. Wounding, as well as application of the plant hormones abscisic acid and ethylene, resulted in accumulation of hevein transcripts in leaves, stems and latex, but not in roots, as shown by using the cDNA as a probe. A fusion protein was produced in E. coli from the protein of the present invention and maltose binding protein produced by the E. coli.

Raikhel, Natasha V. (Okemos, MI); Broekaert, Willem F. (Dilbeek, BE); Chua, Nam-Hai (Scarsdale, NY); Kush, Anil (New York, NY)

1999-05-04T23:59:59.000Z

111

cDNA encoding a polypeptide including a hevein sequence  

DOE Patents (OSTI)

A cDNA clone (HEV1) encoding hevein was isolated via polymerase chain reaction (PCR) using mixed oligonucleotides corresponding to two regions of hevein as primers and a Hevea brasiliensis latex cDNA library as a template. HEV1 is 1,018 nucleotides long and includes an open reading frame of 204 amino acids. The deduced amino acid sequence contains a putative signal sequence of 17 amino acid residues followed by a 187 amino acid polypeptide. The amino-terminal region (43 amino acids) is identical to hevein and shows homology to several chitin-binding proteins and to the amino-termini of wound-induced genes in potato and poplar. The carboxyl-terminal portion of the polypeptide (144 amino acids) is 74--79% homologous to the carboxyl-terminal region of wound-inducible genes of potato. Wounding, as well as application of the plant hormones abscisic acid and ethylene, resulted in accumulation of hevein transcripts in leaves, stems and latex, but not in roots, as shown by using the cDNA as a probe. A fusion protein was produced in E. coli from the protein of the present invention and maltose binding protein produced by the E. coli. 11 figures.

Raikhel, N.V.; Broekaert, W.F.; Chua, N.H.; Kush, A.

1995-03-21T23:59:59.000Z

112

Gas reactor international cooperative program. HTR-synfuel application assessment  

SciTech Connect

This study assesses the technical, environmental and economic factors affecting the application of the High Temperature Gas-Cooled Thermal Reactor (HTR) to: synthetic fuel production; and displacement of fossil fuels in other industrial and chemical processes. Synthetic fuel application considered include coal gasification, direct coal liquefaction, oil shale processing, and the upgrading of syncrude to motor fuel. A wide range of other industrial heat applications was also considered, with emphasis on the use of the closed-loop thermochemical energy pipeline to supply heat to dispersed industrial users. In this application syngas (H/sub 2/ +CO/sub 2/) is produced at the central station HTR by steam reforming and the gas is piped to individual methanators where typically 1000/sup 0/F steam is generated at the industrial user sites. The products of methanation (CH/sub 4/ + H/sub 2/O) are piped back to the reformer at the central station HTR.

1979-09-01T23:59:59.000Z

113

Performance Considerations for Alternatives to 3He-Based Neutron Counters for Safeguards Applications  

Science Conference Proceedings (OSTI)

Worldwide, significant effort has been expended to develop replacement technologies for 3He-filled proportional counters used as neutron detectors and employed extensively in applications as diverse as Homeland Security portal monitoring to fundamental scientific research. Far less attention has been paid to the specific needs of safeguards measurement systems to meet mission objectives such as international obligations under the Nuclear Non-Proliferation Treaty. The measurement configuration, operational environments, and performance requirements for the typical safeguards assay system are sufficiently different from those of other applications that the new generation of neutron detectors is not generally suitable for use in demanding safeguards applications. To illustrate the performance needs for any viable replacement neutron detector technology, the operational constraints for several typical safeguards measurement systems are considered. Key attributes include achieving adequate efficiency per unit volume and minimal parasitic losses, along with gamma-ray immunity in a unit with high reliability and low maintenance.

McElroy, Robert Dennis [ORNL; Croft, Dr. Stephen [Los Alamos National Laboratory (LANL); Young, Brian M [Canberra Industries, Inc., Meriden, CT

2011-01-01T23:59:59.000Z

114

Design and manufacture of a rear driveline package including limited slip differential for Formula SAE applications  

E-Print Network (OSTI)

This document describes the design and manufacture of a lightweight rear driveline package for a Formula SAE race car. The design focuses on all components needed to transfer power from the chain driven Honda CBR600 F4i ...

Yazicioglu, Tolga T

2008-01-01T23:59:59.000Z

115

Investigation of performance improvements including application of inlet guide vanes to a cross-flow fan .  

E-Print Network (OSTI)

??The inherent characteristics of a cross-flow fan allowing for easy thrust vectoring as well as potential airfoil boundary layer control make it an attractive propulsive (more)

Cordero, Samuel F.

2009-01-01T23:59:59.000Z

116

"Heat Resistant Alloys," in MMPDS-01 includes tensile data ...  

Science Conference Proceedings (OSTI)

The latest handbook on superalloys, The Superalloys: Fundamentals and Applications, by Roger C. Reed of the University of Birmingham4 is now available from...

117

Percentage of Total Natural Gas Commercial Deliveries included in ...  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Prices are in ...

118

Percentage of Total Natural Gas Residential Deliveries included...  

Gasoline and Diesel Fuel Update (EIA)

City Gate Price Residential Price Percentage of Total Residential Deliveries included in Prices Commercial Price Percentage of Total Commercial Deliveries included in Prices...

119

Property:Number of Plants included in Capacity Estimate | Open...  

Open Energy Info (EERE)

of Plants included in Capacity Estimate Jump to: navigation, search Property Name Number of Plants included in Capacity Estimate Property Type Number Retrieved from "http:...

120

Estimating solar access of typical residential rooftops: A case study in San Jose, CA  

DOE Green Energy (OSTI)

Shadows cast by trees and buildings can limit the solar access of rooftop solar-energy systems, including photovoltaic panels and thermal collectors. This study characterizes rooftop shading in a residential neighborhood of San Jose, CA, one of four regions analyzed in a wider study of the solar access of California homes.High-resolution orthophotos and LiDAR (Light Detection And Ranging) measurements of surface height were used to create a digital elevation model of all trees and buildings in a 4 km2 residential neighborhood. Hourly shading of roofing planes (the flat elements of roofs) was computed geometrically from the digital elevation model. Parcel boundaries were used to determine the extent to which roofing planes were shaded by trees and buildings in neighboring parcels.In the year in which surface heights were measured (2005), shadows from all sources ("total shading") reduced the insolation received by S-, SW-, and W-facing residential roofing planes in the study area by 13 - 16percent. Shadows cast by trees and buildings in neighboring parcels reduced insolation by no more than 2percent. After 30 years of simulated maximal tree growth, annual total shading increased to 19 - 22percent, and annual extraparcel shading increased to 3 - 4percent.

Levinson, Ronnen M.; Gupta, Smita; Akbari, Hashem; Pomerantz, Melvin

2008-03-03T23:59:59.000Z

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Natural Gas Deliveries to Commercial Consumers (Including Vehicle ...  

U.S. Energy Information Administration (EIA)

Natural Gas Deliveries to Commercial Consumers (Including Vehicle Fuel through 1996) in Wisconsin (Million Cubic Feet)

122

Applications of Probabilistic Risk Assessment  

SciTech Connect

This report provides a summary of potential and actual applications of Probabilistic Risk Assessment (PRA) technology and insights. Individual applications are derived from the experiences of a number of US nuclear utilities. This report identifies numerous applications of PRA techniques beyond those typically associated with PRAs. In addition, believing that the future use of PRA techniques should not be limited to those of the past, areas of plant operations, maintenance, and financial resource allocation are discussed. 9 refs., 3 tabs.

Burns, K.J.; Chapman, J.R.; Follen, S.M.; O'Regan, P.J. (Yankee Atomic Electric Co., Bolton, MA (USA))

1991-05-01T23:59:59.000Z

123

Simulation of Control Options for HVAC Management of a Typical Office Julien CAILLET julien.caillet@mines-paristech.fr  

E-Print Network (OSTI)

Simulation of Control Options for HVAC Management of a Typical Office Building. Julien CAILLET thermal comfort and to reduce energy consumption of buildings. Among defect correction, HVAC control appears as a way of significant improvement. HVAC control is examined by using a dynamic simulation

Paris-Sud XI, Université de

124

Application Acceleration  

NLE Websites -- All DOE Office Websites (Extended Search)

Acceleration Acceleration on Current and Future Cray Platforms Alice Koniges, Robert Preissl, Jihan Kim, Lawrence Berkeley National Laboratory David Eder, Aaron Fisher, Nathan Masters, Velimir Mlaker, Lawrence Livermore National Laboratory Stephane Ethier, Weixing Wang, Princeton Plasma Physics Laboratory Martin Head-Gordon, University of California, Berkeley and Nathan Wichmann, Cray Inc. ABSTRACT: Application codes in a variety of areas are being updated for performance on the latest architectures. We describe current bottlenecks and performance improvement areas for applications including plasma physics, chemistry related to carbon capture and sequestration, and material science. We include a variety of methods including advanced hybrid parallelization using multi-threaded MPI, GPU acceleration, libraries and auto- parallelization compilers. KEYWORDS: hybrid

125

Improving target acquisition in Web applications with link prediction  

E-Print Network (OSTI)

Web application users spend considerable time clicking on hyperlinks and buttons to complete frequent tasks. Individual application developers can optimize their interfaces to improve typical usage; however, no single task ...

Hanna, Roger B

2007-01-01T23:59:59.000Z

126

Energetics of a Symmetric Circulation Including Momentum Constraints  

Science Conference Proceedings (OSTI)

A theory of available potential energy (APE) for symmetric circulations, which includes momentum constraints, is presented. The theory is a generalization of the classical theory of APE, which includes only thermal constraints on the circulation. ...

Sorin Codoban; Theodore G. Shepherd

2003-08-01T23:59:59.000Z

127

Guam Refinery Thermal Cracking/Other (including Gas Oil ...  

U.S. Energy Information Administration (EIA)

Guam Refinery Thermal Cracking/Other (including Gas Oil) Downstream Charge Capacity as of January 1 (Barrels per Stream Day)

128

Scheduling optimization of a real flexible job shop including side ...  

E-Print Network (OSTI)

Aug 19, 2013 ... including side constraints regarding preventive maintenance, fixture availabil- ...... Engineering and Engineering Management, pp. 787791.

129

Physics Applications  

NLE Websites -- All DOE Office Websites (Extended Search)

Applications Applications Technetium-99m radioisotope generator developed at Brookhaven. Numerous physics-related programs at Brookhaven have yielded major advances in medicine and various technologies. Brookhaven's nuclear medicine program, which began in the 1950s, uses the Brookhaven Linac Isotope Producer to make radioisotopes for nuclear medicine diagnostics and treatment throughout the world. Today, more than 85 percent of all imaging examinations worldwide use one of the radioisotopes developed at Brookhaven. At Brookhaven's Center for Translational Neuroimaging, researchers can peer into a living brain through the use of various imaging modalities, including positron emission tomography (PET), magnetic resonance imaging (MRI), and optical imaging. Such research has led to a new understanding of

130

Underwater Gliders: Recent Developments and Future Applications  

E-Print Network (OSTI)

Underwater Gliders: Recent Developments and Future Applications (Invited Paper) R. Bachmayer, N underwater vehicles, and in particular au- tonomous underwater gliders, represent a rapidly maturing of an underwater glider system for propulsion, control, communication and sensing. A typical glider operation

Leonard, Naomi

131

Application of computer blast modeling to oil shale mining  

SciTech Connect

In recent years there has been considerable interest in the development of computer models to describe rock fragmentation by blasting. The interest for this work has come primarily for application to large scale coal or mineral surface mines. However, the basic models developed for these applications are equally applicable for examining typical underground oil shale operations. Models that can predict blasting results starting from first principles can impact room and pillar mining in a number of ways including optimizing round design, control of particle size, evaluation of new explosives, minimizing pillar damage, and developing blasting schemes that can be used in conjunction with continuous miners. In this study, the authors explore how these codes can be used to model the blasting geometry encountered in room and pillar mining operations.

Hommert, P.J.; Preece, D.S.; Thorne, B.J. (Sandia National Labs., Albuquerque, NM (USA))

1989-01-01T23:59:59.000Z

132

A Flux Parameterization Including the Effects of Capillary Waves and Sea State  

Science Conference Proceedings (OSTI)

An airsea interaction model that includes turbulent transport due to capillary waves (surface ripples) is developed. The model differs from others in that the physical premises are applicable to low wind speeds (10-m wind speed, U10 < 5 m s?1) ...

Mark A. Bourassa; Dayton G. Vincent; W. L. Wood

1999-05-01T23:59:59.000Z

133

Block-structured adaptive mesh refinement - theory, implementation and application  

SciTech Connect

Structured adaptive mesh refinement (SAMR) techniques can enable cutting-edge simulations of problems governed by conservation laws. Focusing on the strictly hyperbolic case, these notes explain all algorithmic and mathematical details of a technically relevant implementation tailored for distributed memory computers. An overview of the background of commonly used finite volume discretizations for gas dynamics is included and typical benchmarks to quantify accuracy and performance of the dynamically adaptive code are discussed. Large-scale simulations of shock-induced realistic combustion in non-Cartesian geometry and shock-driven fluid-structure interaction with fully coupled dynamic boundary motion demonstrate the applicability of the discussed techniques for complex scenarios.

Deiterding, Ralf [ORNL

2011-01-01T23:59:59.000Z

134

Asymptotic of the largest and typical dimensions of isotypic components of tensor representations of the symmetric group  

E-Print Network (OSTI)

Vershik and Kerov in \\cite{VK85} gave asymptotical bounds for the maximal and typical dimensions of the irreducible representations of the symmetric group. It was conjectured by Grigori Olshanski that the maximal and typical dimensions of the isotypical components of the representations in the base of Schur-Weyl duality accept similar asymptotical bounds. Using the method of Vershik and Kerov the conjecture of Grigori Olshanski is proven in this paper. More precisely, consider the tensor representation of the symmetric group on $N$ letters on the space $(C^r)^{\\tensor N}$. The isotypical components of this representation are parametrized by Young diagrams with $N$ cells and at most $r$ rows, and the relative dimensions of these components give rise to a measure on the set of such Young diagrams. Philippe Biane in \\cite{Biane2001} found the limit shape of a typical Young diagram with respect to this measure in the limit when $N$ grows and $\\sqrt{N}/r$ converges to a constant. By showing that this limit shape i...

Mkrtchyan, Sevak

2010-01-01T23:59:59.000Z

135

Percentage of Total Natural Gas Industrial Deliveries included...  

U.S. Energy Information Administration (EIA) Indexed Site

Pipeline and Distribution Use Price City Gate Price Residential Price Percentage of Total Residential Deliveries included in Prices Commercial Price Percentage of Total Commercial...

136

Natural Gas Delivered to Consumers in California (Including ...  

U.S. Energy Information Administration (EIA)

Natural Gas Delivered to Consumers in California (Including Vehicle Fuel) (Million Cubic Feet) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec; ...

137

FAQ 23-How much depleted uranium -- including depleted uranium...  

NLE Websites -- All DOE Office Websites (Extended Search)

is stored in the United States? How much depleted uranium -- including depleted uranium hexafluoride -- is stored in the United States? In addition to the depleted uranium stored...

138

Electrical machines and assemblies including a yokeless stator ...  

Wind Energy; Partners (27) Visual Patent Search; Success Stories; News; Events; Electrical machines and assemblies including a yokeless stator with modular lamination ...

139

U.S. Refinery Thermal Cracking, Other (including Gas Oil ...  

U.S. Energy Information Administration (EIA)

U.S. Refinery Thermal Cracking, Other (including Gas Oil) Downstream Charge Capacity as of January 1 (Barrels per Stream Day)

140

[Article 1 of 7: Motivates and Includes the Consumer  

NLE Websites -- All DOE Office Websites (Extended Search)

will be diverse and widespread, including renewables, distributed generation, and energy storage. And they will increase rapidly all along the value chain, from suppliers to...

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Including Retro-Commissioning in Federal Energy Savings Performance...  

NLE Websites -- All DOE Office Websites (Extended Search)

11.2 Retro-Cx in Federal ESPCs Including Retro-Commissioning In Federal Energy Saving Performance Contracts Retro-commissioning generally reduces operating and maintenance costs,...

142

PLOT: A UNIX PROGRAM FOR INCLUDING GRAPHICS IN DOCUMENTS  

E-Print Network (OSTI)

simple, easy-to-read graphics language designed specificallyPROGRAM FOR INCLUDING GRAPHICS IN DOCUMENTS Pavel Curtismeanings as in the GRAFPAC graphics system. Definl. ~ tions

Curtis, Pavel

2013-01-01T23:59:59.000Z

143

Natural Gas Deliveries to Commercial Consumers (Including Vehicle...  

Gasoline and Diesel Fuel Update (EIA)

Natural Gas Deliveries to Commercial Consumers (Including Vehicle Fuel through 1996) in South Dakota (Million Cubic Feet) Natural Gas Deliveries to Commercial Consumers...

144

Natural Gas Delivered to Consumers in South Dakota (Including...  

Gasoline and Diesel Fuel Update (EIA)

History: Monthly Annual Download Data (XLS File) Natural Gas Delivered to Consumers in South Dakota (Including Vehicle Fuel) (Million Cubic Feet) Natural Gas Delivered to...

145

The Organic Rankine Cycle System, Its Application to Extract Energy From Low Temperature Waste Heat  

E-Print Network (OSTI)

The conservation of energy by its recovery from low temperature waste heat is of increasing importance in today's world energy crisis. The Organic Rankine Cycle is a cost efficient and proven method of converting low temperature (200-400o F) waste heat to mechanical and/or electrical energy. Applying the Organic Rankine Cycle technology to typical liquid and mixed component condensing streams is described using actual examples. Selection of the organic working fluid is explored. The Rankine Cycle efficiency is directly dependent upon the temperature difference between its evaporating and condensing phases. The evaporating level is set by the heat source; therefore, to maximize efficiency, it is essential to obtain the lowest condensing temperature practical. Various condensing schemes are discussed emphasizing methods of optimizing the net output of the total system. Several Organic Rankine Cycle commercial applications are summarized with experience and general performance given. The economics and optimization techniques in typical applications including multiple heat sources are discussed.

Sawyer, R. H.; Ichikawa, S.

1980-01-01T23:59:59.000Z

146

Solar Energy Education. Reader, Part II. Sun story. [Includes glossary  

DOE Green Energy (OSTI)

Magazine articles which focus on the subject of solar energy are presented. The booklet prepared is the second of a four part series of the Solar Energy Reader. Excerpts from the magazines include the history of solar energy, mythology and tales, and selected poetry on the sun. A glossary of energy related terms is included. (BCS)

Not Available

1981-05-01T23:59:59.000Z

147

Energy Transitions: A Systems Approach Including Marcellus Shale Gas Development  

E-Print Network (OSTI)

Energy Transitions: A Systems Approach Including Marcellus Shale Gas Development A Report: A Systems Approach Including Marcellus Shale Gas Development Executive Summary In the 21st century new we focused on the case of un- conventional natural gas recovery from the Marcellus shale In addition

Walter, M.Todd

148

Energy Transitions: A Systems Approach Including Marcellus Shale Gas Development  

E-Print Network (OSTI)

Energy Transitions: A Systems Approach Including Marcellus Shale Gas Development A Report Transitions: A Systems Approach Including Marcellus Shale Gas Development Executive Summary In the 21st the Marcellus shale In addition to the specific questions identified for the case of Marcellus shale gas in New

Angenent, Lars T.

149

1) What are the current and future communications needs of utilities, including  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

(1) What are the current and future communications needs of utilities, including for the (1) What are the current and future communications needs of utilities, including for the deployment of new Smart Grid applications, and how are these needs being met? The current communication needs of SCE include: telephony, data, video, voice dispatch, mobile data, grid monitoring, grid control, tele-protection, customer communication, load management, automated meter reading, and collaboration capabilities ranging from virtual meetings to e-learning. SCE is using a combination of private, leased, and shared telecommunication networks to support these requirements. Those applications that require high availability, low latency, and stringent security rely on a private telecommunications network (SCEnet). A combination of transport media are

150

What To Include In The Whistleblower Complaint? | National Nuclear Security  

National Nuclear Security Administration (NNSA)

To Include In The Whistleblower Complaint? | National Nuclear Security To Include In The Whistleblower Complaint? | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Continuing Management Reform Countering Nuclear Terrorism About Us Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Media Room Congressional Testimony Fact Sheets Newsletters Press Releases Speeches Events Social Media Video Gallery Photo Gallery NNSA Archive Federal Employment Apply for Our Jobs Our Jobs Working at NNSA Blog What To Include In The Whistleblower Complaint? Home > About Us > Our Operations > Management and Budget > Whistleblower Program > What To Include In The Whistleblower Complaint? What To Include In The Whistleblower Complaint?

151

T-603: Mac OS X Includes Some Invalid Comodo Certificates | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

03: Mac OS X Includes Some Invalid Comodo Certificates 03: Mac OS X Includes Some Invalid Comodo Certificates T-603: Mac OS X Includes Some Invalid Comodo Certificates April 15, 2011 - 1:46am Addthis PROBLEM: Mac OS X Includes Some Invalid Comodo Certificates PLATFORM: For Mac OS X Server v10.5.8, Mac OS X v10.5.8, Mac OS X v10.6.7 and Mac OS X Server v10.6.7 ABSTRACT: The operating system includes some invalid certificates. The vulnerability is due to the invalid certificates and not the operating system itself. Other browsers, applications, and operating systems are affected. reference LINKS: SecurityTracker Alert ID: 1025362 APPLE-SA-2011-04-14-4 Security Update 2011-002 Apple Support Downloads IMPACT ASSESSMENT: High Discussion: A partner of Comodo with Registration Authority capabilities suffered an internal security breach and the attacker caused seven certificates to be

152

Including uncertainty in hazard analysis through fuzzy measures  

Science Conference Proceedings (OSTI)

This paper presents a method for capturing the uncertainty expressed by an Hazard Analysis (HA) expert team when estimating the frequencies and consequences of accident sequences and provides a sound mathematical framework for propagating this uncertainty to the risk estimates for these accident sequences. The uncertainty is readily expressed as distributions that can visually aid the analyst in determining the extent and source of risk uncertainty in HA accident sequences. The results also can be expressed as single statistics of the distribution in a manner analogous to expressing a probabilistic distribution as a point-value statistic such as a mean or median. The study discussed here used data collected during the elicitation portion of an HA on a high-level waste transfer process to demonstrate the techniques for capturing uncertainty. These data came from observations of the uncertainty that HA team members expressed in assigning frequencies and consequences to accident sequences during an actual HA. This uncertainty was captured and manipulated using ideas from possibility theory. The result of this study is a practical method for displaying and assessing the uncertainty in the HA team estimates of the frequency and consequences for accident sequences. This uncertainty provides potentially valuable information about accident sequences that typically is lost in the HA process.

Bott, T.F.; Eisenhawer, S.W.

1997-12-01T23:59:59.000Z

153

U-182: Microsoft Windows Includes Some Invalid Certificates | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

82: Microsoft Windows Includes Some Invalid Certificates 82: Microsoft Windows Includes Some Invalid Certificates U-182: Microsoft Windows Includes Some Invalid Certificates June 4, 2012 - 7:00am Addthis PROBLEM: A vulnerability was reported in Microsoft Windows. A remote user may be able to spoof code signing signatures. PLATFORM: Version(s): XP SP3, 2003 SP2, Vista SP2, 2008 SP2, 7 SP1, 2008 R2 SP1; and prior service packs ABSTRACT: The operating system includes some invalid intermediate certificates. The vulnerability is due to the certificate authorities and not the operating system itself. Reference Links: Security tracker ID 1027114 GENERIC-MAP-NOMATCH Vendor Advisory IMPACT ASSESSMENT: High Discussion: The invalid certificates and their thumbprints are: Microsoft Enforced Licensing Intermediate PCA: 2a 83 e9 02 05 91 a5 5f c6

154

Removal of mineral matter including pyrite from coal  

SciTech Connect

Mineral matter, including pyrite, is removed from coal by treatment of the coal with aqueous alkali at a temperature of about 175.degree. to 350.degree. C, followed by acidification with strong acid.

Reggel, Leslie (Pittsburgh, PA); Raymond, Raphael (Bethel Park, PA); Blaustein, Bernard D. (Pittsburgh, PA)

1976-11-23T23:59:59.000Z

155

Free Energy Efficiency Kit includes CFL light bulbs,  

E-Print Network (OSTI)

Free Energy Efficiency Kit Kit includes CFL light bulbs, spray foam, low-flow shower head, and more i ci e n cy On Thursday, March 31st New River Light & Power will sponsor a seminar that is designed

Rose, Annkatrin

156

Characterizations of Aircraft Icing Environments that Include Supercooled Large Drops  

Science Conference Proceedings (OSTI)

Measurements of aircraft icing environments that include supercooled large drops (SLD) greater than 50 ?m in diameter have been made during 38 research flights. These flights were conducted during the First and Third Canadian Freezing Drizzle ...

Stewart G. Cober; George A. Isaac; J. Walter Strapp

2001-11-01T23:59:59.000Z

157

Including costs of supply chain risk in strategic sourcing decisions  

E-Print Network (OSTI)

Cost evaluations do not always include the costs associated with risks when organizations make strategic sourcing decisions. This research was conducted to establish and quantify the impact of risks and risk-related costs ...

Jain, Avani

2009-01-01T23:59:59.000Z

158

Including Atmospheric Layers in Vegetation and Urban Offline Surface Schemes  

Science Conference Proceedings (OSTI)

A formulation to include prognostic atmospheric layers in offline surface schemes is derived from atmospheric equations. Whereas multilayer schemes developed previously need a complex coupling between atmospheric-model levels and surface-scheme ...

Valry Masson; Yann Seity

2009-07-01T23:59:59.000Z

159

Percentage of Total Natural Gas Commercial Deliveries included in Prices  

Gasoline and Diesel Fuel Update (EIA)

City Gate Price Residential Price Percentage of Total Residential Deliveries included in Prices Commercial Price Percentage of Total Commercial Deliveries included in Prices Industrial Price Percentage of Total Industrial Deliveries included in Prices Electric Power Price Period: Monthly Annual City Gate Price Residential Price Percentage of Total Residential Deliveries included in Prices Commercial Price Percentage of Total Commercial Deliveries included in Prices Industrial Price Percentage of Total Industrial Deliveries included in Prices Electric Power Price Period: Monthly Annual Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes Show Data By: Data Series Area May-13 Jun-13 Jul-13 Aug-13 Sep-13 Oct-13 View History U.S. 63.3 59.3 57.9 57.0 57.4 61.3 1983-2013 Alabama 71.7 71.0 68.5 68.2 68.4 66.7 1989-2013 Alaska 94.1 91.6 91.1 91.0 92.3 92.6 1989-2013 Arizona 84.0 83.0 81.6 80.3 82.8 82.7 1989-2013 Arkansas 37.8 28.3 28.1 28.6 26.7 28.0 1989-2013

160

Percentage of Total Natural Gas Industrial Deliveries included in Prices  

Gasoline and Diesel Fuel Update (EIA)

City Gate Price Residential Price Percentage of Total Residential Deliveries included in Prices Commercial Price Percentage of Total Commercial Deliveries included in Prices Industrial Price Percentage of Total Industrial Deliveries included in Prices Electric Power Price Period: Monthly Annual City Gate Price Residential Price Percentage of Total Residential Deliveries included in Prices Commercial Price Percentage of Total Commercial Deliveries included in Prices Industrial Price Percentage of Total Industrial Deliveries included in Prices Electric Power Price Period: Monthly Annual Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes Show Data By: Data Series Area May-13 Jun-13 Jul-13 Aug-13 Sep-13 Oct-13 View History U.S. 16.5 16.3 16.0 16.2 16.6 16.9 2001-2013 Alabama 22.1 21.7 21.6 22.8 22.0 22.7 2001-2013 Alaska 100.0 100.0 100.0 100.0 100.0 100.0 2001-2013 Arizona 13.4 15.7 15.3 13.8 13.7 13.9 2001-2013 Arkansas 1.7 1.4 1.2 1.4 1.3 1.5 2001-2013

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Contaminant distributions at typical U.S. uranium milling facilities and their effect on remedial action decisions  

SciTech Connect

Past operations at uranium processing sites throughout the US have resulted in local contamination of soils and ground water by radionuclides, toxic metals, or both. Understanding the origin of contamination and how the constituents are distributed is a basic element for planning remedial action decisions. This report describes the radiological and nonradiological species found in ground water at a typical US uranium milling facility. The report will provide the audience with an understanding of the vast spectrum of contaminants that must be controlled in planning solutions to the long-term management of these waste materials.

Hamp, S. [USDOE Albuquerque Operations Office, NM (United States). Uranium Mill Tailings Remedial Action Project Office; Jackson, T.J. [Geraghty and Miller, Inc., Albuquerque, NM (United States); Dotson, P.W. [Roy F. Weston, Inc., Albuquerque, NM (United States)

1995-03-01T23:59:59.000Z

162

The test data challenge for database-driven applications  

Science Conference Proceedings (OSTI)

Business applications rely typically on databases for storing and processing their data (database-driven applications, or DBAPs). Testing DBAPs requires testing the application logic plus the interaction between the application logic and the database. ... Keywords: databases, information systems, test coverage, test data, testing

Klaus Haller

2010-06-01T23:59:59.000Z

163

CALTECH CORE-COLLAPSE PROJECT (CCCP) OBSERVATIONS OF TYPE IIn SUPERNOVAE: TYPICAL PROPERTIES AND IMPLICATIONS FOR THEIR PROGENITOR STARS  

SciTech Connect

Type IIn supernovae (SNe IIn) are rare events, constituting only a few percent of all core-collapse SNe, and the current sample of well-observed SNe IIn is small. Here, we study the four SNe IIn observed by the Caltech Core-Collapse Project (CCCP). The CCCP SN sample is unbiased to the extent that object selection was not influenced by target SN properties. Therefore, these events are representative of the observed population of SNe IIn. We find that a narrow P-Cygni profile in the hydrogen Balmer lines appears to be a ubiquitous feature of SNe IIn. Our light curves show a relatively long rise time (>20 days) followed by a slow decline stage (0.01-0.15 mag day{sup -1}), and a typical V-band peak magnitude of M{sub V} = -18.4 {+-} 1.0 mag. We measure the progenitor star wind velocities (600-1400 km s{sup -1}) for the SNe in our sample and derive pre-explosion mass-loss rates (0.026-0.12 M{sub Sun} yr{sup -1}). We compile similar data for SNe IIn from the literature and discuss our results in the context of this larger sample. Our results indicate that typical SNe IIn arise from progenitor stars that undergo luminous-blue-variable-like mass loss shortly before they explode.

Kiewe, Michael; Gal-Yam, Avishay; Arcavi, Iair [Benoziyo Center for Astrophysics, Faculty of Physics, Weizmann Institute of Science, Rehovot 76100 (Israel); Leonard, Douglas C.; Emilio Enriquez, J. [Department of Astronomy, San Diego State University, San Diego, CA 92182 (United States); Bradley Cenko, S. [Department of Astronomy, University of California, Berkeley, CA 94720-3411 (United States); Fox, Derek B. [Department of Astronomy and Astrophysics, 525 Davey Laboratory, Pennsylvania State University, University Park, PA 16802 (United States); Moon, Dae-Sik [Department of Astronomy and Astrophysics, University of Toronto, Toronto, ON M5S 3H4 (Canada); Sand, David J.; Soderberg, Alicia M., E-mail: avishay.gal-yam@weizmann.ac.il [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, Cambridge, MA 02138 (United States)

2012-01-01T23:59:59.000Z

164

Introduction to Small-Scale Photovoltaic Systems (Including RETScreen Case  

Open Energy Info (EERE)

Introduction to Small-Scale Photovoltaic Systems (Including RETScreen Case Introduction to Small-Scale Photovoltaic Systems (Including RETScreen Case Study) (Webinar) Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Introduction to Small-Scale Photovoltaic Systems (Including RETScreen Case Study) (Webinar) Focus Area: Solar Topics: Market Analysis Website: www.leonardo-energy.org/webinar-introduction-small-scale-photovoltaic- Equivalent URI: cleanenergysolutions.org/content/introduction-small-scale-photovoltaic Language: English Policies: Deployment Programs DeploymentPrograms: Project Development This video teaches the viewer about photovoltaic arrays and RETscreen's photovoltaic module, which can be used to project the cost and production of an array. An example case study was

165

projects are valued at approximately $67 million (including $15 million  

NLE Websites -- All DOE Office Websites (Extended Search)

projects are valued at approximately $67 million (including $15 million projects are valued at approximately $67 million (including $15 million in non-Federal cost sharing) over four years. The overall goal of the research is to develop carbon dioxide (CO 2 ) capture and separation technologies that can achieve at least 90 percent CO 2 removal at no more than a 35 percent increase in the cost of electricity. The projects, managed by FE's National Energy Technology Laboratory (NETL), include: (1) Linde, LLC, which will use a post-combustion capture technology incorporating BASF's novel amine-based process at a 1-megawatt electric (MWe) equivalent slipstream pilot plant at the National Carbon Capture Center (NCCC) (DOE contribution: $15 million); (2) Neumann Systems Group, Inc., which will design, construct, and test a patented NeuStreamTM absorber at the Colorado

166

Honda Smart Home to Include Berkeley Lab Ventilation Controller  

NLE Websites -- All DOE Office Websites (Extended Search)

Honda Smart Home to Include Berkeley Lab Ventilation Controller Honda Smart Home to Include Berkeley Lab Ventilation Controller Honda smart home October 2013 October-November Special Focus: Energy Efficiency, Buildings, and the Electric Grid Honda Motor Company Inc is proceeding with plans to build a Smart Home in Davis, California, to demonstrate the latest in renewable energy technologies and energy efficiency. The home is expected to produce more energy than is consumed, demonstrating how the goal of "zero net energy" can be met in the near term future. A ventilation controller developed by researchers at Berkeley Lab's Environmental Energy Technologies Division (EETD) will be included in the smart home. EETD is currently working with the developers of the home control system to integrate its control algorithms.

167

DOE Revises its NEPA Regulations, Including Categorical Exclusions |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Revises its NEPA Regulations, Including Categorical Exclusions Revises its NEPA Regulations, Including Categorical Exclusions DOE Revises its NEPA Regulations, Including Categorical Exclusions September 30, 2011 - 2:30pm Addthis On September 27, 2011, the Department of Energy (DOE) approved revisions to its National Environmental Policy Act (NEPA) regulations, and on September 28th, submitted the revisions to the Federal Register. The final regulations, which become effective 30 days after publication in the Federal Register, are the culmination of a 2-year process to review and update DOE's NEPA implementing procedures. This process involved internal evaluation, public participation, and Council on Environmental Quality (CEQ) review. The revisions are designed to focus Departmental resources on projects with the potential for significant environmental impact, to better

168

Solar Energy Education. Renewable energy: a background text. [Includes glossary  

SciTech Connect

Some of the most common forms of renewable energy are presented in this textbook for students. The topics include solar energy, wind power hydroelectric power, biomass ocean thermal energy, and tidal and geothermal energy. The main emphasis of the text is on the sun and the solar energy that it yields. Discussions on the sun's composition and the relationship between the earth, sun and atmosphere are provided. Insolation, active and passive solar systems, and solar collectors are the subtopics included under solar energy. (BCS)

1985-01-01T23:59:59.000Z

169

Thin film solar cell including a spatially modulated intrinsic layer  

SciTech Connect

One or more thin film solar cells in which the intrinsic layer of substantially amorphous semiconductor alloy material thereof includes at least a first band gap portion and a narrower band gap portion. The band gap of the intrinsic layer is spatially graded through a portion of the bulk thickness, said graded portion including a region removed from the intrinsic layer-dopant layer interfaces. The band gap of the intrinsic layer is always less than the band gap of the doped layers. The gradation of the intrinsic layer is effected such that the open circuit voltage and/or the fill factor of the one or plural solar cell structure is enhanced.

Guha, Subhendu (Troy, MI); Yang, Chi-Chung (Troy, MI); Ovshinsky, Stanford R. (Bloomfield Hills, MI)

1989-03-28T23:59:59.000Z

170

Solar Energy Education. Renewable energy: a background text. [Includes glossary  

DOE Green Energy (OSTI)

Some of the most common forms of renewable energy are presented in this textbook for students. The topics include solar energy, wind power hydroelectric power, biomass ocean thermal energy, and tidal and geothermal energy. The main emphasis of the text is on the sun and the solar energy that it yields. Discussions on the sun's composition and the relationship between the earth, sun and atmosphere are provided. Insolation, active and passive solar systems, and solar collectors are the subtopics included under solar energy. (BCS)

Not Available

1985-01-01T23:59:59.000Z

171

cDNA encoding a polypeptide including a hevein sequence  

DOE Patents (OSTI)

A cDNA clone (HEV1) encoding hevein was isolated via polymerase chain reaction (PCR) using mixed oligonucleotides corresponding to two regions of hevein as primers and a Hevea brasiliensis latex cDNA library as a template. HEV1 is 1,018 nucleotides long and includes an open reading frame of 204 amino acids.

Raikhel, N.V.; Broekaert, W.F.; Namhai Chua; Kush, A.

1993-02-16T23:59:59.000Z

172

Thermal Unit Commitment Including Optimal AC Power Flow Constraints  

E-Print Network (OSTI)

Thermal Unit Commitment Including Optimal AC Power Flow Constraints Carlos Murillo{Sanchez Robert J algorithm for unit commitment that employs a Lagrange relaxation technique with a new augmentation. This framework allows the possibility of committing units that are required for the VArs that they can produce

173

Method for including operation and maintenance costs in the economic analysis of active solar energy systems  

DOE Green Energy (OSTI)

For a developing technology such as solar energy, the costs for operation and maintenance (O and M) can be substantial. In the past, most economic analyses included these costs by simply assuming that an annual cost will be incurred that is proportional to the initial cost of the system. However, in assessing the economics of new systems proposed for further research and development, such a simplification can obscure the issues. For example, when the typical method for including O and M costs in an economic analysis is used, the O and M costs associated with a newly developed, more reliable, and slightly more expensive controller will be assumed to increase - an obvious inconsistency. The method presented in this report replaces this simplistic approach with a representation of the O and M costs that explicitly accounts for the uncertainties and risks inherent in the operation of any equipment. A detailed description of the data inputs required by the method is included as well as a summary of data sources and an example of the method as applied to an active solar heating system.

Short, W.D.

1986-08-01T23:59:59.000Z

174

DOE Considers Natural Gas Utility Service Options: Proposal Includes  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Considers Natural Gas Utility Service Options: Proposal Considers Natural Gas Utility Service Options: Proposal Includes 30-mile Natural Gas Pipeline from Pasco to Hanford DOE Considers Natural Gas Utility Service Options: Proposal Includes 30-mile Natural Gas Pipeline from Pasco to Hanford January 23, 2012 - 12:00pm Addthis Media Contacts Cameron Hardy, DOE , (509) 376-5365, Cameron.Hardy@rl.doe.gov RICHLAND, WASH. - The U.S. Department of Energy (DOE) is considering natural gas transportation and distribution requirements to support the Waste Treatment Plant (WTP) and evaporator operations at the Hanford Site in southeastern Washington State. DOE awarded a task order worth up to $5 million to the local, licensed supplier of natural gas in the Hanford area, Cascade Natural Gas Corporation (Cascade). Cascade will support DOE and its Environmental

175

Italy (including San Marino) Fossil-Fuel CO2 Emissions  

NLE Websites -- All DOE Office Websites (Extended Search)

Western Europe » Italy Western Europe » Italy (including San Marino) Italy (including San Marino) Fossil-Fuel CO2 Emissions Graph graphic Graphics Data graphic Data Trends As occurred in many industrialized nations, CO2 emissions from Italy rose steeply since the late 1940's until the growth was abruptly terminated in 1974. Since 1974, emissions from liquid fuels have vacillated, dropping from 76% to 46% of a static but varying total. Significant increases in natural gas consumption have compensated for the drop in oil consumption. In 2008, 35.8% of Italy's fossil-fuel CO2 emissions were due to natural gas consumption. Coal usage grew steadily until 1985 when CO2 emissions from coal consumption reached 16 million metric tons of carbon. Not until 2004 did coal usage exceed 1985 levels and now accounts for 13.9% of Italy's

176

Coordination). Participants include representatives from Balancing Authorities (BAs), Reliability  

E-Print Network (OSTI)

The MRO Subject Matter Expert Team is an industry stakeholder group which includes subject matter experts from MRO member organizations in various technical areas. Any materials, guidance, and views from stakeholder groups are meant to be helpful to industry participants; but should not be considered approved or endorsed by MRO staff or its board of directors unless specified. Page | 2 Disclaimer The Midwest Reliability Organization (MRO) Standards Committee (SC) is committed to providing training and non-binding guidance to industry stakeholders regarding existing and emerging Reliability Standards. Any materials, including presentations, were developed through the MRO SC by Subject Matter Experts (SMEs) from member organizations within the MRO region. In 2012, SMEs in the field of System Operator Communications were brought together to prepare a guide for complying with NERC Reliability Standard COM-002-2 (Communications and

Will Behnke; Alliant Energy; Jacalynn Bentz; Great River Energy; Marie Knox Miso; Jacalynn Bentz; Marie Knox; Terry Harbour

2013-01-01T23:59:59.000Z

177

Flicker Performance of Modern Lighting Technologies including Impacts of Dimmers  

Science Conference Proceedings (OSTI)

The existing industry standards on flicker measurement and assessment are based on the response of general purpose incandescent lamps. However, worldwide these lamps are being replaced with more energy efficient lamps including Compact Fluorescent Lamps (CFLs) and Light emitting Diode (LED) lamps. In order to keep the flicker standards relevant, the industry standard bodies on the subject are in need of the evidence that compares the flicker performance of new lighting ...

2012-12-12T23:59:59.000Z

178

Conversion of geothermal waste to commercial products including silica  

DOE Patents (OSTI)

A process for the treatment of geothermal residue includes contacting the pigmented amorphous silica-containing component with a depigmenting reagent one or more times to depigment the silica and produce a mixture containing depigmented amorphous silica and depigmenting reagent containing pigment material; separating the depigmented amorphous silica and from the depigmenting reagent to yield depigmented amorphous silica. Before or after the depigmenting contacting, the geothermal residue or depigmented silica can be treated with a metal solubilizing agent to produce another mixture containing pigmented or unpigmented amorphous silica-containing component and a solubilized metal-containing component; separating these components from each other to produce an amorphous silica product substantially devoid of metals and at least partially devoid of pigment. The amorphous silica product can be neutralized and thereafter dried at a temperature from about 25.degree. C. to 300.degree. C. The morphology of the silica product can be varied through the process conditions including sequence contacting steps, pH of depigmenting reagent, neutralization and drying conditions to tailor the amorphous silica for commercial use in products including filler for paint, paper, rubber and polymers, and chromatographic material.

Premuzic, Eugene T. (East Moriches, NY); Lin, Mow S. (Rocky Point, NY)

2003-01-01T23:59:59.000Z

179

Multi-processor including data flow accelerator module  

DOE Patents (OSTI)

An accelerator module for a data flow computer includes an intelligent memory. The module is added to a multiprocessor arrangement and uses a shared tagged memory architecture in the data flow computer. The intelligent memory module assigns locations for holding data values in correspondence with arcs leading to a node in a data dependency graph. Each primitive computation is associated with a corresponding memory cell, including a number of slots for operands needed to execute a primitive computation, a primitive identifying pointer, and linking slots for distributing the result of the cell computation to other cells requiring that result as an operand. Circuitry is provided for utilizing tag bits to determine automatically when all operands required by a processor are available and for scheduling the primitive for execution in a queue. Each memory cell of the module may be associated with any of the primitives, and the particular primitive to be executed by the processor associated with the cell is identified by providing an index, such as the cell number for the primitive, to the primitive lookup table of starting addresses. The module thus serves to perform functions previously performed by a number of sections of data flow architectures and coexists with conventional shared memory therein. A multiprocessing system including the module operates in a hybrid mode, wherein the same processing modules are used to perform some processing in a sequential mode, under immediate control of an operating system, while performing other processing in a data flow mode.

Davidson, George S. (Albuquerque, NM); Pierce, Paul E. (Albuquerque, NM)

1990-01-01T23:59:59.000Z

180

Global Analysis of Solar Neutrino Oscillations Including SNO CC Measurement  

E-Print Network (OSTI)

For active and sterile neutrinos, we present the globally allowed solutions for two neutrino oscillations. We include the SNO CC measurement and all other relevant solar neutrino and reactor data. Five active neutrino oscillation solutions (LMA, LOW, SMA, VAC, and Just So2) are currently allowed at 3 sigma; three sterile neutrino solutions (Just So2, SMA, and VAC) are allowed at 3 sigma. The goodness of fit is satisfactory for all eight solutions. We also investigate the robustness of the allowed solutions by carrying out global analyses with and without: 1) imposing solar model constraints on the 8B neutrino flux, 2) including the Super-Kamiokande spectral energy distribution and day-night data, 3) including a continuous mixture of active and sterile neutrinos, 4) using an enhanced CC cross section for deuterium (due to radiative corrections), and 5) a optimistic, hypothetical reduction by a factor of three of the error of the SNO CC rate. For every analysis strategy used in this paper, the most favored solutions all involve large mixing angles: LMA, LOW, or VAC. The favored solutions are robust, but the presence at 3 sigma of individual sterile solutions and the active Just So2 solution is sensitive to the analysis assumptions.

John N. Bahcall; M. C. Gonzalez-Garcia; Carlos Pena-Garay

2001-06-25T23:59:59.000Z

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Life cycle support for sensor network applications  

Science Conference Proceedings (OSTI)

Developing applications for sensor networks is a challenging task. Most programming systems narrowly focus on programming issues while ignoring that programming represents only a tiny fraction of the typical life cycle of an application. Furthermore, ... Keywords: assessment, middleware, sensor networks, separation of concerns, software engineering

Urs Bischoff; Gerd Kortuem

2007-11-01T23:59:59.000Z

182

Information regarding previous INCITE awards including selected highlights  

Office of Science (SC) Website

Information regarding previous INCITE awards including selected highlights Advanced Scientific Computing Research (ASCR) ASCR Home About Research Facilities Accessing ASCR Supercomputers Oak Ridge Leadership Computing Facility (OLCF) Argonne Leadership Computing Facility (ALCF) National Energy Research Scientific Computing Center (NERSC) Energy Sciences Network (ESnet) Research & Evaluation Prototypes (REP) Innovative & Novel Computational Impact on Theory and Experiment (INCITE) ASCR Leadership Computing Challenge (ALCC) Science Highlights Benefits of ASCR Funding Opportunities Advanced Scientific Computing Advisory Committee (ASCAC) News & Resources Contact Information Advanced Scientific Computing Research U.S. Department of Energy SC-21/Germantown Building

183

Composite armor, armor system and vehicle including armor system  

DOE Patents (OSTI)

Composite armor panels are disclosed. Each panel comprises a plurality of functional layers comprising at least an outermost layer, an intermediate layer and a base layer. An armor system incorporating armor panels is also disclosed. Armor panels are mounted on carriages movably secured to adjacent rails of a rail system. Each panel may be moved on its associated rail and into partially overlapping relationship with another panel on an adjacent rail for protection against incoming ordnance from various directions. The rail system may be configured as at least a part of a ring, and be disposed about a hatch on a vehicle. Vehicles including an armor system are also disclosed.

Chu, Henry S.; Jones, Warren F.; Lacy, Jeffrey M.; Thinnes, Gary L.

2013-01-01T23:59:59.000Z

184

Composite material including nanocrystals and methods of making  

DOE Patents (OSTI)

Temperature-sensing compositions can include an inorganic material, such as a semiconductor nanocrystal. The nanocrystal can be a dependable and accurate indicator of temperature. The intensity of emission of the nanocrystal varies with temperature and can be highly sensitive to surface temperature. The nanocrystals can be processed with a binder to form a matrix, which can be varied by altering the chemical nature of the surface of the nanocrystal. A nanocrystal with a compatibilizing outer layer can be incorporated into a coating formulation and retain its temperature sensitive emissive properties

Bawendi, Moungi G. (Boston, MA); Sundar, Vikram C. (New York, NY)

2008-02-05T23:59:59.000Z

185

Wind energy applications guide  

DOE Green Energy (OSTI)

The brochure is an introduction to various wind power applications for locations with underdeveloped transmission systems, from remote water pumping to village electrification. It includes an introductory section on wind energy, including wind power basics and system components and then provides examples of applications, including water pumping, stand-alone systems for home and business, systems for community centers, schools, and health clinics, and examples in the industrial area. There is also a page of contacts, plus two specific example applications for a wind-diesel system for a remote station in Antarctica and one on wind-diesel village electrification in Russia.

anon.

2001-01-01T23:59:59.000Z

186

Community Assessment Tool for Public Health Emergencies Including Pandemic Influenza  

SciTech Connect

The Community Assessment Tool (CAT) for Public Health Emergencies Including Pandemic Influenza (hereafter referred to as the CAT) was developed as a result of feedback received from several communities. These communities participated in workshops focused on influenza pandemic planning and response. The 2008 through 2011 workshops were sponsored by the Centers for Disease Control and Prevention (CDC). Feedback during those workshops indicated the need for a tool that a community can use to assess its readiness for a disaster - readiness from a total healthcare perspective, not just hospitals, but the whole healthcare system. The CAT intends to do just that - help strengthen existing preparedness plans by allowing the healthcare system and other agencies to work together during an influenza pandemic. It helps reveal each core agency partners (sectors) capabilities and resources, and highlights cases of the same vendors being used for resource supplies (e.g., personal protective equipment [PPE] and oxygen) by the partners (e.g., public health departments, clinics, or hospitals). The CAT also addresses gaps in the community's capabilities or potential shortages in resources. This tool has been reviewed by a variety of key subject matter experts from federal, state, and local agencies and organizations. It also has been piloted with various communities that consist of different population sizes, to include large urban to small rural communities.

ORAU's Oak Ridge Institute for Science Education (HCTT-CHE)

2011-04-14T23:59:59.000Z

187

Community Assessment Tool for Public Health Emergencies Including Pandemic Influenza  

SciTech Connect

The Community Assessment Tool (CAT) for Public Health Emergencies Including Pandemic Influenza (hereafter referred to as the CAT) was developed as a result of feedback received from several communities. These communities participated in workshops focused on influenza pandemic planning and response. The 2008 through 2011 workshops were sponsored by the Centers for Disease Control and Prevention (CDC). Feedback during those workshops indicated the need for a tool that a community can use to assess its readiness for a disaster - readiness from a total healthcare perspective, not just hospitals, but the whole healthcare system. The CAT intends to do just that - help strengthen existing preparedness plans by allowing the healthcare system and other agencies to work together during an influenza pandemic. It helps reveal each core agency partners (sectors) capabilities and resources, and highlights cases of the same vendors being used for resource supplies (e.g., personal protective equipment [PPE] and oxygen) by the partners (e.g., public health departments, clinics, or hospitals). The CAT also addresses gaps in the community's capabilities or potential shortages in resources. This tool has been reviewed by a variety of key subject matter experts from federal, state, and local agencies and organizations. It also has been piloted with various communities that consist of different population sizes, to include large urban to small rural communities.

ORAU' s Oak Ridge Institute for Science Education (HCTT-CHE)

2011-04-14T23:59:59.000Z

188

Introduction to Small-Scale Wind Energy Systems (Including RETScreen Case  

Open Energy Info (EERE)

Introduction to Small-Scale Wind Energy Systems (Including RETScreen Case Introduction to Small-Scale Wind Energy Systems (Including RETScreen Case Study) (Webinar) Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Introduction to Small-Scale Wind Energy Systems (Including RETScreen Case Study) (Webinar) Focus Area: Renewable Energy Topics: System & Application Design Website: www.leonardo-energy.org/webinar-introduction-small-scale-wind-energy-s Equivalent URI: cleanenergysolutions.org/content/introduction-small-scale-wind-energy- Language: English Policies: Deployment Programs DeploymentPrograms: Project Development This video teaches the viewer about wind turbines and RETscreen's wind module, which can be used to project the cost and production of a wind

189

Notices ROUTINE USES OF RECORDS MAINTAINED IN THE SYSTEM, INCLUDING  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

83 Federal Register 83 Federal Register / Vol. 78, No. 51 / Friday, March 15, 2013 / Notices ROUTINE USES OF RECORDS MAINTAINED IN THE SYSTEM, INCLUDING CATEGORIES OF USERS AND THE PURPOSES OF SUCH USES: The Department may disclose information contained in a record in this system of records under the routine uses listed in this system of records without the consent of the individual if the disclosure is compatible with the purposes for which the record was collected. These disclosures may be made on a case-by-case basis or, if the Department has complied with the computer matching requirements of the Privacy Act of 1974, as amended (Privacy Act), under a computer matching agreement. Any disclosure of individually identifiable information from a record in this system must also comply with the requirements of section

190

Copper laser modulator driving assembly including a magnetic compression laser  

DOE Patents (OSTI)

A laser modulator (10) having a low voltage assembly (12) with a plurality of low voltage modules (14) with first stage magnetic compression circuits (20) and magnetic assist inductors (28) with a common core (91), such that timing of the first stage magnetic switches (30b) is thereby synchronized. A bipolar second stage of magnetic compression (42) is coupled to the low voltage modules (14) through a bipolar pulse transformer (36) and a third stage of magnetic compression (44) is directly coupled to the second stage of magnetic compression (42). The low voltage assembly (12) includes pressurized boxes (117) for improving voltage standoff between the primary winding assemblies (34) and secondary winding (40) contained therein.

Cook, Edward G. (Livermore, CA); Birx, Daniel L. (Oakley, CA); Ball, Don G. (Livermore, CA)

1994-01-01T23:59:59.000Z

191

[Article 1 of 7: Motivates and Includes the Consumer]  

NLE Websites -- All DOE Office Websites (Extended Search)

2 of 7: Research on the Characteristics of a Modern Grid by the NETL 2 of 7: Research on the Characteristics of a Modern Grid by the NETL Modern Grid Strategy Team Accommodates All Generation and Storage Options Last month we presented the first Principal Characteristic of a Modern Grid, "Motivates and Includes the Consumer". This month we present a second characteristic, "Accommodates All Generation and Storage Options". This characteristic will fundamentally transition today's grid from a centralized model for generation to one that also has a more balanced contribution from decentralized generation and storage. This characteristic, along with the other six, define a Modern Grid that will power the 21 st Century economy. For a more detailed discussion on "Accommodates All Generation and Storage Options", please see:

192

Search for Earth-like planets includes LANL star analysis  

NLE Websites -- All DOE Office Websites (Extended Search)

Search for earth-like planets Search for earth-like planets Search for Earth-like planets includes LANL star analysis The mission will not only be able to search for planets around other stars, but also yield new insights into the parent stars themselves. March 6, 2009 Los Alamos National Laboratory sits on top of a once-remote mesa in northern New Mexico with the Jemez mountains as a backdrop to research and innovation covering multi-disciplines from bioscience, sustainable energy sources, to plasma physics and new materials. Los Alamos National Laboratory sits on top of a once-remote mesa in northern New Mexico with the Jemez mountains as a backdrop to research and innovation covering multi-disciplines from bioscience, sustainable energy sources, to plasma physics and new materials.

193

Dye laser amplifier including a specifically designed diffuser assembly  

SciTech Connect

A large (high flow rate) dye laser amplifier in which a continuous replened supply of dye is excited by a first light beam, specifically a copper vapor laser beam, in order to amplify the intensity of a second different light beam, specifically a dye beam, passing through the dye is disclosed herein. This amplifier includes a dye cell defining a dye chamber through which a continuous stream of dye is caused to pass at a relatively high flow rate and a specifically designed diffuser assembly for slowing down the flow of dye while, at the same time, assuring that as the dye stream flows through the diffuser assembly it does so in a stable manner.

Davin, James (Gilroy, CA); Johnston, James P. (Stanford, CA)

1992-01-01T23:59:59.000Z

194

Hydraulic engine valve actuation system including independent feedback control  

DOE Patents (OSTI)

A hydraulic valve actuation assembly may include a housing, a piston, a supply control valve, a closing control valve, and an opening control valve. The housing may define a first fluid chamber, a second fluid chamber, and a third fluid chamber. The piston may be axially secured to an engine valve and located within the first, second and third fluid chambers. The supply control valve may control a hydraulic fluid supply to the piston. The closing control valve may be located between the supply control valve and the second fluid chamber and may control fluid flow from the second fluid chamber to the supply control valve. The opening control valve may be located between the supply control valve and the second fluid chamber and may control fluid flow from the supply control valve to the second fluid chamber.

Marriott, Craig D

2013-06-04T23:59:59.000Z

195

A thermovoltaic semiconductor device including a plasma filter  

DOE Patents (OSTI)

A thermovoltaic energy conversion device and related method for converting thermal energy into an electrical potential are disclosed. An interference filter is provided on a semiconductor thermovoltaic cell to pre-filter black body radiation. The semiconductor thermovoltaic cell includes a P/N junction supported on a substrate which converts incident thermal energy below the semiconductor junction band gap into electrical potential. The semiconductor substrate is doped to provide a plasma filter which reflects back energy having a wavelength which is above the band gap and which is ineffectively filtered by the interference filter, through the P/N junction to the source of radiation thereby avoiding parasitic absorption of the unusable portion of the thermal radiation energy.

Baldasaro, Paul F.

1997-12-01T23:59:59.000Z

196

ERIP application instructions  

SciTech Connect

This report provides background information and instructions to assist applicants in writing Energy-Related Inventions Program (ERIP) applications. Initial feedback fro usage for the new instructions shows that the best instructions would not be read and followed by all applicants. Applications from more than thirty applicants who have received the new instructions indicated that few had read the instructions. Based on this feedback, the instructions have been further revised to include a title page and table of contents. A warning was also added to advise applicants of the potential penalty of delayed review if these instructions are not followed. This revision was intended to address the possibility that some applicants did not see or bother to follow the instructions which followed the background information about ERIP. Included are two examples of ERIP applications which have been prepared for handout at workshops or mailing to applicants. Writing of example applications was time consuming and more difficult than expected for several reasons: (1) Full disclosures can be lengthy, very detailed, and technical. This contrasts with the desire to prepare examples which are comparatively short and easy for the non-technical person to read. (2) Disclosures contain confidential information which should not be published. (3) It is difficult to imagine that applicants will study examples when they do not bother to read the basic instructions.

Watt, D.M.

1992-01-02T23:59:59.000Z

197

Extractant composition including crown ether and calixarene extractants  

SciTech Connect

An extractant composition comprising a mixed extractant solvent consisting of calix[4] arene-bis-(tert-octylbenzo)-crown-6 ("BOBCalixC6"), 4',4',(5')-di-(t-butyldicyclo-hexano)-18-crown-6 ("DtBu18C6"), and at least one modifier dissolved in a diluent. The DtBu18C6 may be present at from approximately 0.01M to approximately 0.4M, such as at from approximately 0.086 M to approximately 0.108 M. The modifier may be 1-(2,2,3,3-tetrafluoropropoxy)-3-(4-sec-butylphenoxy)-2-propanol ("Cs-7SB") and may be present at from approximately 0.01M to approximately 0.8M. In one embodiment, the mixed extractant solvent includes approximately 0.15M DtBu18C6, approximately 0.007M BOBCalixC6, and approximately 0.75M Cs-7SB modifier dissolved in an isoparaffinic hydrocarbon diluent. The extractant composition further comprises an aqueous phase. The mixed extractant solvent may be used to remove cesium and strontium from the aqueous phase.

Meikrantz, David H. (Idaho Falls, ID); Todd, Terry A. (Aberdeen, ID); Riddle, Catherine L. (Idaho Falls, ID); Law, Jack D. (Pocalello, ID); Peterman, Dean R. (Idaho Falls, ID); Mincher, Bruce J. (Idaho Falls, ID); McGrath, Christopher A. (Blackfoot, ID); Baker, John D. (Blackfoot, ID)

2009-04-28T23:59:59.000Z

198

Analysis of 70 Ophiuchi AB including seismic constraints  

E-Print Network (OSTI)

The analysis of solar-like oscillations for stars belonging to a binary system provides a unique opportunity to probe the internal stellar structure and to test our knowledge of stellar physics. Such oscillations have been recently observed and characterized for the A component of the 70 Ophiuchi system. A model of 70 Ophiuchi AB that correctly reproduces all observational constraints available for both stars is determined. An age of 6.2 +- 1.0 Gyr is found with an initial helium mass fraction Y_i=0.266 +- 0.015 and an initial metallicity (Z/X)_i=0.0300 +- 0.0025 when atomic diffusion is included and a solar value of the mixing-length parameter assumed. A precise and independent determination of the value of the mixing-length parameter needed to model 70 Oph A requires accurate measurement of the mean small separation, which is not available yet. Current asteroseismic observations, however, suggest that the value of the mixing-length parameter of 70 Oph A is lower or equal to the solar calibrated value. The e...

Eggenberger, P; Carrier, F; Fernandes, J; Santos, N C

2008-01-01T23:59:59.000Z

199

Analysis of alpha Centauri AB including seismic constraints  

E-Print Network (OSTI)

Detailed models of alpha Cen A and B based on new seismological data for alpha Cen B by Carrier & Bourban (2003) have been computed using the Geneva evolution code including atomic diffusion. Taking into account the numerous observational constraints now available for the alpha Cen system, we find a stellar model which is in good agreement with the astrometric, photometric, spectroscopic and asteroseismic data. The global parameters of the alpha Cen system are now firmly constrained to an age of t=6.52+-0.30 Gyr, an initial helium mass fraction Y_i=0.275+-0.010 and an initial metallicity (Z/X)_i=0.0434+-0.0020. Thanks to these numerous observational constraints, we confirm that the mixing-length parameter alpha of the B component is larger than the one of the A component, as already suggested by many authors (Noels et al. 1991, Fernandes & Neuforge 1995 and Guenther & Demarque 2000): alpha_B is about 8% larger than alpha_A (alpha_A=1.83+-0.10 and alpha_B=1.97+-0.10). Moreover, we show that asteroseismic measurements enable to determine the radii of both stars with a very high precision (errors smaller than 0.3%). The radii deduced from seismological data are compatible with the new interferometric results of Kervella et al. (2003) even if they are slightly larger than the interferometric radii (differences smaller than 1%).

P. Eggenberger; C. Charbonnel; S. Talon; G. Meynet; A. Maeder; F. Carrier; G. Bourban

2004-01-29T23:59:59.000Z

200

Analysis of 70 Ophiuchi AB including seismic constraints  

E-Print Network (OSTI)

The analysis of solar-like oscillations for stars belonging to a binary system provides a unique opportunity to probe the internal stellar structure and to test our knowledge of stellar physics. Such oscillations have been recently observed and characterized for the A component of the 70 Ophiuchi system. A model of 70 Ophiuchi AB that correctly reproduces all observational constraints available for both stars is determined. An age of 6.2 +- 1.0 Gyr is found with an initial helium mass fraction Y_i=0.266 +- 0.015 and an initial metallicity (Z/X)_i=0.0300 +- 0.0025 when atomic diffusion is included and a solar value of the mixing-length parameter assumed. A precise and independent determination of the value of the mixing-length parameter needed to model 70 Oph A requires accurate measurement of the mean small separation, which is not available yet. Current asteroseismic observations, however, suggest that the value of the mixing-length parameter of 70 Oph A is lower or equal to the solar calibrated value. The effects of atomic diffusion and of the choice of the adopted solar mixture were also studied. We also tested and compared the theoretical tools used for the modeling of stars for which p-modes frequencies are detected by performing this analysis with three different stellar evolution codes and two different calibration methods. We found that the different evolution codes and calibration methods we used led to perfectly coherent results.

P. Eggenberger; A. Miglio; F. Carrier; J. Fernandes; N. C. Santos

2008-02-25T23:59:59.000Z

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Interim performance criteria for photovoltaic energy systems. [Glossary included  

DOE Green Energy (OSTI)

This document is a response to the Photovoltaic Research, Development, and Demonstration Act of 1978 (P.L. 95-590) which required the generation of performance criteria for photovoltaic energy systems. Since the document is evolutionary and will be updated, the term interim is used. More than 50 experts in the photovoltaic field have contributed in the writing and review of the 179 performance criteria listed in this document. The performance criteria address characteristics of present-day photovoltaic systems that are of interest to manufacturers, government agencies, purchasers, and all others interested in various aspects of photovoltaic system performance and safety. The performance criteria apply to the system as a whole and to its possible subsystems: array, power conditioning, monitor and control, storage, cabling, and power distribution. They are further categorized according to the following performance attributes: electrical, thermal, mechanical/structural, safety, durability/reliability, installation/operation/maintenance, and building/site. Each criterion contains a statement of expected performance (nonprescriptive), a method of evaluation, and a commentary with further information or justification. Over 50 references for background information are also given. A glossary with definitions relevant to photovoltaic systems and a section on test methods are presented in the appendices. Twenty test methods are included to measure performance characteristics of the subsystem elements. These test methods and other parts of the document will be expanded or revised as future experience and needs dictate.

DeBlasio, R.; Forman, S.; Hogan, S.; Nuss, G.; Post, H.; Ross, R.; Schafft, H.

1980-12-01T23:59:59.000Z

202

Community Assessment Tool for Public Health Emergencies Including Pandemic Influenza  

SciTech Connect

The Community Assessment Tool (CAT) for Public Health Emergencies Including Pandemic Influenza (hereafter referred to as the CAT) was developed as a result of feedback received from several communities. These communities participated in workshops focused on influenza pandemic planning and response. The 2008 through 2011 workshops were sponsored by the Centers for Disease Control and Prevention (CDC). Feedback during those workshops indicated the need for a tool that a community can use to assess its readiness for a disasterreadiness from a total healthcare perspective, not just hospitals, but the whole healthcare system. The CAT intends to do just thathelp strengthen existing preparedness plans by allowing the healthcare system and other agencies to work together during an influenza pandemic. It helps reveal each core agency partners' (sectors) capabilities and resources, and highlights cases of the same vendors being used for resource supplies (e.g., personal protective equipment [PPE] and oxygen) by the partners (e.g., public health departments, clinics, or hospitals). The CAT also addresses gaps in the community's capabilities or potential shortages in resources. While the purpose of the CAT is to further prepare the community for an influenza pandemic, its framework is an extension of the traditional all-hazards approach to planning and preparedness. As such, the information gathered by the tool is useful in preparation for most widespread public health emergencies. This tool is primarily intended for use by those involved in healthcare emergency preparedness (e.g., community planners, community disaster preparedness coordinators, 9-1-1 directors, hospital emergency preparedness coordinators). It is divided into sections based on the core agency partners, which may be involved in the community's influenza pandemic influenza response.

HCTT-CHE

2011-04-14T23:59:59.000Z

203

Community Assessment Tool for Public Health Emergencies Including Pandemic Influenza  

SciTech Connect

The Community Assessment Tool (CAT) for Public Health Emergencies Including Pandemic Influenza (hereafter referred to as the CAT) was developed as a result of feedback received from several communities. These communities participated in workshops focused on influenza pandemic planning and response. The 2008 through 2011 workshops were sponsored by the Centers for Disease Control and Prevention (CDC). Feedback during those workshops indicated the need for a tool that a community can use to assess its readiness for a disasterreadiness from a total healthcare perspective, not just hospitals, but the whole healthcare system. The CAT intends to do just thathelp strengthen existing preparedness plans by allowing the healthcare system and other agencies to work together during an influenza pandemic. It helps reveal each core agency partners' (sectors) capabilities and resources, and highlights cases of the same vendors being used for resource supplies (e.g., personal protective equipment [PPE] and oxygen) by the partners (e.g., public health departments, clinics, or hospitals). The CAT also addresses gaps in the community's capabilities or potential shortages in resources. While the purpose of the CAT is to further prepare the community for an influenza pandemic, its framework is an extension of the traditional all-hazards approach to planning and preparedness. As such, the information gathered by the tool is useful in preparation for most widespread public health emergencies. This tool is primarily intended for use by those involved in healthcare emergency preparedness (e.g., community planners, community disaster preparedness coordinators, 9-1-1 directors, hospital emergency preparedness coordinators). It is divided into sections based on the core agency partners, which may be involved in the community's influenza pandemic influenza response.

HCTT-CHE

2011-04-14T23:59:59.000Z

204

Application Surveillance and Success Stories of Synchrophasors  

Science Conference Proceedings (OSTI)

This report is an overview of the status of the use of synchrophasor data in the development of new applications and improvements to existing applications. It includes a technology review and industry experiences with implementation of synchrophasor data enhanced applications.

2010-12-22T23:59:59.000Z

205

Balance of Plant Needs and Integration of Stack Components for Stationary Power and CHP Applications  

NLE Websites -- All DOE Office Websites (Extended Search)

Balance of Plant Needs and Balance of Plant Needs and Integration of Stack Components for Stationary Power and CHP Applications Applications Chris Ainscough P.E. Chief Engineer - PowerEdge Nuvera Fuel Cells cainscough@nuvera.com Background  Experience integrating systems based on fuel cells and reformers.  Applications include vehicles, combined heat and power (CHP), industrial plants, and forklifts. Who Needs Balance of Plant?  "...an electric generator that has no moving parts...This elegant device is called a fuel cell." Skerrett, P. J. "Fuel Cell Update." Popular Science. June 1993:89. print. No Moving Parts Except These  The typical fluid components in a PEM CHP system based on steam/methane reformer technology. (in red) SWITCH STACK PRV

206

APPLICATION NOTE 4393 Selecting HB LED Drivers for Automotive Lighting Applications  

E-Print Network (OSTI)

Abstract: This application note provides an overview of HB LED driver selection criteria for automotive lighting applications. It reviews HB LED driver topologies and recommends configurations for various automotive lighting applications, including interior lighting, exterior lighting, and display backlighting.

Brian Hedayati

2009-01-01T23:59:59.000Z

207

HTS applications  

E-Print Network (OSTI)

Superconductivity has found many attractive applications in medicine, science, power systems, engineering, transport and electronics. One of the most prominent applications of superconductivity are superconducting magnets e.g. MRI magnets, NMR magnets, accelerator magnets, and magnets for fusion; most applications still use low temperature superconductors. Since the discovery of high temperature superconductivity (HTS) in 1986 there has been a tremendous progress in R&D of HTS material, wires and applications. Especially for power system applications, HTS offers considerable economic benefits. Many HTS demonstrator or prototype applications have been built and successfully tested, and some HTS applications like cables and superconducting fault current limiters seem very close to commercialisation. This paper gives an overview about the present and future HTS applications in power applications, high field magnets and current leads. In addition results of the Forschungszentrum Karlsruhe program to develop H...

Noe, M; Fietz, W H; Goldacker, W; Schneider, Th

2009-01-01T23:59:59.000Z

208

DEVELOPMENT OF PLASTICITY MODEL USING NON ASSOCIATED FLOW RULE FOR HCP MATERIALS INCLUDING ZIRCONIUM FOR NUCLEAR APPLICATIONS  

SciTech Connect

In this report (prepared in collaboration with Prof. Jeong Whan Yoon, Deakin University, Melbourne, Australia) a research effort was made to develop a non associated flow rule for zirconium. Since Zr is a hexagonally close packed (hcp) material, it is impossible to describe its plastic response under arbitrary loading conditions with any associated flow rule (e.g. von Mises). As a result of strong tension compression asymmetry of the yield stress and anisotropy, zirconium displays plastic behavior that requires a more sophisticated approach. Consequently, a new general asymmetric yield function has been developed which accommodates mathematically the four directional anisotropies along 0 degrees, 45 degrees, 90 degrees, and biaxial, under tension and compression. Stress anisotropy has been completely decoupled from the r value by using non associated flow plasticity, where yield function and plastic potential have been treated separately to take care of stress and r value directionalities, respectively. This theoretical development has been verified using Zr alloys at room temperature as an example as these materials have very strong SD (Strength Differential) effect. The proposed yield function reasonably well models the evolution of yield surfaces for a zirconium clock rolled plate during in plane and through thickness compression. It has been found that this function can predict both tension and compression asymmetry mathematically without any numerical tolerance and shows the significant improvement compared to any reported functions. Finally, in the end of the report, a program of further research is outlined aimed at constructing tensorial relationships for the temperature and fluence dependent creep surfaces for Zr, Zircaloy 2, and Zircaloy 4.

Michael V. Glazoff; Jeong-Whan Yoon

2013-08-01T23:59:59.000Z

209

Application of Pinch Technology in Refinery Retrofits  

E-Print Network (OSTI)

This paper reviews the application of pinch technology in the identification of the most attractive retrofit prospects in typical refineries. In the first part of the paper, methodology is described to identify attractive inter-unit heat integration opportunities as well as attractive process-utility system integration (co-generation). An example of an atmospheric pipestill-alkylation unit integration evaluation is given using both composite stream and Grand composite stream methods. In the second part of the paper, the application of pinch technology in a typical intra-unit heat integration problem is given. It is explained how inefficiencies in an APS crude preheat train are identified, and a typical small retrofit project is described.

Thomas, W. R.; Siegell, J. H.; Sideropoulos, T.; Robertson, J. L.; Papoulias, S. A.

1987-09-01T23:59:59.000Z

210

MAAP4 Applications Guidance  

Science Conference Proceedings (OSTI)

The existing Modular Accident Analysis Program Version 4 (MAAP4) documentation consists of the MAAP4 User's Manual, the MAAP4 user's guides for input preparation, and transmittal documents that describe individual revisions. These components contain detailed information on the mechanics of running the code as well as detailed descriptions of the individual models, but they do not include specific applications guidance. This applications guidance document is intended to fill that gap by providing sufficie...

2010-07-30T23:59:59.000Z

211

Applications of coatings in coal-fired energy systems  

SciTech Connect

Corrosion and erosion of metallic structural materials at elevated temperatures in complex multicomponent gas environments that include particulates are potential problems in many fossil energy systems, especially those using coal as a feedstock. The use of appropriate corrosion-resistant coatings on metallic components offers an avenue to minimize material degradation and extend component life. The purpose of this paper is to review the current status of coating performance in environments typical of pulverized-coal-fired boilers, coal gasification, fluidized-bed combustion, and gas turbines. The paper discusses the complexity of environments in different systems and the coating requirements for acceptable performance. Examples illustrate the morphology and corrosion/erosion performance of coating/structural alloy combinations exposed in some of these systems. La addition, future research and development needs are discussed for coating applications in several coal-fired systems.

Natesan, K.

1992-03-01T23:59:59.000Z

212

PDF Application  

Science Conference Proceedings (OSTI)

?Computer Applications and Process Control. ?Copper Nickel and Cobalt ... ? Iron and Steel. ?Joining. ?Lead Zinc and Tin. ?Lightweight Materials.

213

Cathodic Protection System Application and Maintenance Guide  

Science Conference Proceedings (OSTI)

Typically, cathodic protection system equipment includes rectifiers, anodes, anode junction boxes, reference cells (electrodes), and test stations. The scope of this guide includes addressing the maintenance and testing of the system, its components, and providing appropriate recommendations. These recommendations will provide the basis for a suitable preventive (PM) and predictive (PdM) maintenance program.

2005-12-23T23:59:59.000Z

214

Technologies Applications  

E-Print Network (OSTI)

evaporation systems n Potential mining applications (produced water) nIndustry applications for which silicaLicensable Technologies Applications: n Cooling tower systems n Water treatment systems n Water needed n Decreases the amount of makeup water and subsequent discharged water (blowdown) n Enables

215

Energy Use Savings for a Typical New Residential Dwelling Unit Based on the 2009 and 2012 IECC as Compared to the 2006 IECC  

Science Conference Proceedings (OSTI)

The 2009 and 2012 International Energy Conservation Codes (IECC) require a substantial improvement in energy efficiency compared to the 2006 IECC. This report averages the energy use savings for a typical new residential dwelling unit based on the 2009 and 2012 IECC compared to the 2006 IECC. Results are reported by the eight climate zones in the IECC and for the national average.

Lucas, Robert G.; Mendon, Vrushali V.; Goel, Supriya

2012-06-01T23:59:59.000Z

216

Performance measurement of magnetohydrodynamic code for space plasma on typical scalar-type supercomputer systems with a large number of cores  

Science Conference Proceedings (OSTI)

The computational performance of magnetohydrodynamic (MHD) code is evaluated on two typical scalar-type supercomputer systems. We have carried out performance tuning of a three-dimensional MHD code for space plasma simulations on the HA8000 (with 8192 ... Keywords: magnetohydrodynamics simulation, parallel computing, performance evaluation, scalar massively computer system

Keiichiro Fukazawa; Takayuki Umeda

2012-08-01T23:59:59.000Z

217

Nowadays, a large spectrum of knowledge is required from PhD students working within the area of Energy Conversion Systems. Nevertheless, typical PhD  

E-Print Network (OSTI)

of Energy Conversion Systems. Nevertheless, typical PhD comptetences are often restricted to their fieldTech Summer School « Integrated Approach to Energy Systems » is to make up for those lacks, bring out the main challenges and provide methodological approaches to address multi-disciplinary energy-related challenges

218

Transportation Applications  

DOE Green Energy (OSTI)

The purpose of this project is to systematically identify and examine possible near and long-term ecological and environmental effects from the production of hydrogen from various energy sources based on the DOE hydrogen production strategy and the use of that hydrogen in transportation applications. This project uses state-of-the-art numerical modeling tools of the environment and energy system emissions in combination with relevant new and prior measurements and other analyses to assess the understanding of the potential ecological and environmental impacts from hydrogen market penetration. H2 technology options and market penetration scenarios will be evaluated using energy-technology-economics models as well as atmospheric trace gas projections based on the IPCC SRES scenarios including the decline in halocarbons due to the Montreal Protocol. Specifically we investigate the impact of hydrogen releases on the oxidative capacity of the atmosphere, the long-term stability of the ozone layer due to changes in hydrogen emissions, the impact of hydrogen emissions and resulting concentrations on climate, the impact on microbial ecosystems involved in hydrogen uptake, and criteria pollutants emitted from distributed and centralized hydrogen production pathways and their impacts on human health, air quality, ecosystems, and structures under different penetration scenarios

Wuebbles, D.J.; Dubey, M.K., Edmonds, J.; Layzell, D.; Olsen, S.; Rahn, T.; Rocket, A.; Wang, D.; Jia, W.

2010-06-01T23:59:59.000Z

219

RELAP5-3D Code Includes Athena Features and Models  

DOE Green Energy (OSTI)

Version 2.3 of the RELAP5-3D computer program includes all features and models previously available only in the ATHENA version of the code. These include the addition of new working fluids (i.e., ammonia, blood, carbon dioxide, glycerol, helium, hydrogen, lead-bismuth, lithium, lithium-lead, nitrogen, potassium, sodium, and sodium-potassium) and a magnetohydrodynamic model that expands the capability of the code to model many more thermal-hydraulic systems. In addition to the new working fluids along with the standard working fluid water, one or more noncondensable gases (e.g., air, argon, carbon dioxide, carbon monoxide, helium, hydrogen, krypton, nitrogen, oxygen, sf6, xenon) can be specified as part of the vapor/gas phase of the working fluid. These noncondensable gases were in previous versions of RELAP5- 3D. Recently four molten salts have been added as working fluids to RELAP5-3D Version 2.4, which has had limited release. These molten salts will be in RELAP5-3D Version 2.5, which will have a general release like RELAP5-3D Version 2.3. Applications that use these new features and models are discussed in this paper.

Richard A. Riemke; Cliff B. Davis; Richard R. Schultz

2006-07-01T23:59:59.000Z

220

Transportation R and D included in thermal and mechanical sciences program  

Science Conference Proceedings (OSTI)

Argonne National Laboratory is a multiprogram research and development laboratory operated by The University of Chicago for the US Department of Energy. At Argonne, applied research in thermal and mechanical sciences is performed within the Thermal and Mechanical Sciences Section of the Energy Technology Division. Current program areas include compact evaporators and condensers for the process and transportation industries, ice slurries for district cooling, advanced fluids for improved heat transfer and reduced pressure drop, flow-induced vibration and flow distribution in shell-and-tube heat exchangers, and dynamics and control of maglev systems. In general, the objective of the research is to extend the technology base in each of these areas and to facilitate its application in solving problems of importance to US industries and utilities. This is accomplished by developing validated design correlations and predictive methods. The staff of the Thermal and Mechanical Sciences Section have extensive experimental and analytical experience in heat transfer, multiphase flow, structural dynamics and control, fluid-structure interaction, transient flow and mixing, thermally driven flows, and flow visualization using ultra-high-speed video. Large, general-purpose test facilities and smaller, single-purpose test apparatuses are available for experiments and component design evaluation. A world-class capability in the study of flow-induced vibrations exists within the Section. Individual fact sheets, describing currently active research program areas, related facilities, and listing, as a contact, the principal investigator, are included.

NONE

1995-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

PETSc: Applications  

NLE Websites -- All DOE Office Websites (Extended Search)

Applications and Publications Applications and Publications Home Download Features Documentation Applications/Publications Prizes Industrial/DOE sites DOE CSGF users Miscellaneous External Software Developers Site These are publications on application simulations developed by PETSc users. Please send us information about your publications, petsc-maint@mcs.anl.gov. How to cite PETSc in your publications. See Acknowledgments for software packages that PETSc uses. PETSc has been used for modeling in all of these areas: Acoustics, Aerodynamics, Air Pollution, Arterial Flow, Bone Fractures, Brain Surgery, Cancer Surgery, Cancer Treatment, Carbon Sequestration, Cardiology, Cells, CFD, Combustion, Concrete, Corrosion, Data Mining, Dentistry, Earth Quakes, Economics, Fission, Fusion, Glaciers, Ground Water Flow, Linguistics,

222

Application: Electronics  

Science Conference Proceedings (OSTI)

Application: Electronics. ... Suppression of Electrical Cable Fires: Development of a Standard PVC Cable Fire Test for ISO 14520-1.. Robin, ML ...

2011-12-22T23:59:59.000Z

223

Application Form  

Science Conference Proceedings (OSTI)

ELIGIBILITY REQUIREMENTS. The application ... Note: Applying for the travel award does not enter your abstract into the TMS Conference Management System.

224

brochure application  

Science Conference Proceedings (OSTI)

Magnetohydrodynamics. 19. Measurement Techniques for Pot Analysis ... Country ... Be sure to note your personal topics of interest on the application because...

225

Neutron sources and applications  

Science Conference Proceedings (OSTI)

Review of Neutron Sources and Applications was held at Oak Brook, Illinois, during September 8--10, 1992. This review involved some 70 national and international experts in different areas of neutron research, sources, and applications. Separate working groups were asked to (1) review the current status of advanced research reactors and spallation sources; and (2) provide an update on scientific, technological, and medical applications, including neutron scattering research in a number of disciplines, isotope production, materials irradiation, and other important uses of neutron sources such as materials analysis and fundamental neutron physics. This report summarizes the findings and conclusions of the different working groups involved in the review, and contains some of the best current expertise on neutron sources and applications.

Price, D.L. [ed.] [Argonne National Lab., IL (United States); Rush, J.J. [ed.] [National Inst. of Standards and Technology, Gaithersburg, MD (United States)

1994-01-01T23:59:59.000Z

226

ARM: Surface Radiation Measurement Quality Control testing, including climatologically configurable limits  

DOE Data Explorer (OSTI)

Surface Radiation Measurement Quality Control testing, including climatologically configurable limits

Gary Hodges; Tom Stoffel; Mark Kutchenreiter; Bev Kay; Aron Habte; Michael Ritsche; Victor Morris; Mary Anderberg

227

cDNA encoding a polypeptide including a hev ein sequence  

DOE Patents (OSTI)

A cDNA clone (HEV1) encoding hevein was isolated via polymerase chain reaction (PCR) using mixed oligonucleotides corresponding to two regions of hevein as primers and a Hevea brasiliensis latex cDNA library as a template. HEV1 is 1018 nucleotides long and includes an open reading frame of 204 amino acids. The deduced amino acid sequence contains a putative signal sequence of 17 amino acid residues followed by a 187 amino acid polypeptide. The amino-terminal region (43 amino acids) is identical to hevein and shows homology to several chitin-binding proteins and to the amino-termini of wound-induced genes in potato and poplar. The carboxyl-terminal portion of the polypeptide (144 amino acids) is 74-79% homologous to the carboxyl-terminal region of wound-inducible genes of potato. Wounding, as well as application of the plant hormones abscisic acid and ethylene, resulted in accumulation of hevein transcripts in leaves, stems and latex, but not in roots, as shown by using the cDNA as a probe. A fusion protein was produced in E. coli from the protein of the present invention and maltose binding protein produced by the E. coli.

Raikhel, Natasha V. (Okemos, MI); Broekaert, Willem F. (Dilbeek, BE); Chua, Nam-Hai (Scarsdale, NY); Kush, Anil (New York, NY)

2000-07-04T23:59:59.000Z

228

The potential for microtechnology applications in energy systems: Results of an experts workshop  

SciTech Connect

Microscale technologies, or microelectromechanical systems (MEMS), are currently under development in the United States and abroad. Examples include microsensors, microactuators (including micromotors), and microscale heat exchangers. Typically, microscale devices have features ranging in size from a few microns to several millimeters, with fabrication methods adapted from those developed for the semiconductor industry. Microtechnologies are already being commercialized; initial markets include the biomedical and transportation industries. Applications are being developed in other industries as well. Researchers at the Pacific Northwest Laboratory (PNL) hypothesize that a significant number of energy applications are possible. These applications range from environmental sensors that support enhanced control of building (or room) temperature and ventilation to microscale heat pumps and microscale heat engines that could collectively provide for kilowatt quantities of energy conversion. If efficient versions of these devices are developed, they could significantly advance the commercialization of distributed energy conversion systems, thereby reducing the energy losses associated with energy distribution. Based upon the potential for energy savings, the U.S. Department of Energy (DOE) Office of Building Technologies (OBT) has proposed a new initiative in energy systems miniaturization. The program would focus on the development of microtechnologies for the manufactured housing sector and would begin in either FY 1997 or FY 1998, ramping up to $5 million per year investment by FY 2001.

NONE

1995-02-01T23:59:59.000Z

229

Computer applications: a service course  

Science Conference Proceedings (OSTI)

A paperless computer applications course, which is driven by an online syllabus is described. Students demo their work on the computer rather than hand in paper assignments. Several advanced topics are included to challenge the students and downloads ... Keywords: computer applications, data duplication, paperless

Abdul Sattar; Torben Lorenzen

2007-12-01T23:59:59.000Z

230

High power battery test methods for hybrid vehicle applications  

DOE Green Energy (OSTI)

Commonly used EV battery tests are not very suitable for testing hybrid vehicle batteries, which may be primarily intended to supply vehicle acceleration power. The capacity of hybrid vehicle batteries will be relatively small, they will typically operate over a restricted range of states-of-charge, and they may seldom if ever be fully recharged. Further, hybrid propulsion system designs will commonly impose a higher regeneration content than is typical for electric vehicles. New test methods have been developed for use in characterizing battery performance and life for hybrid vehicle use. The procedures described in this paper were developed from the requirements of the government-industry cooperative Partnership for A New Generation of Vehicles (PNGV) program; however, they are expected to have broad application to the testing of energy storage devices for hybrid vehicles. The most important performance measure for a high power battery is its pulse power capability as a function of state-of-charge for both discharge and regeneration pulses. It is also important to characterize cycle life, although the {open_quote}cycles{close_quote} involved are quite different from the conventional full-discharge, full-recharge cycle commonly used for EV batteries, This paper illustrates in detail several test profiles which have been selected for PNGV battery testing, along with some sample results and lessons learned to date from the use of these test profiles. The relationship between the PNGV energy storage requirements and these tests is described so that application of the test methods can be made to other hybrid vehicle performance requirements as well. The resulting test procedures can be used to characterize the pulse power capability of high power energy storage devices including batteries and ultracapacitors, as well as the life expectancy of such devices, for either power assist or dual mode hybrid propulsion system designs.

Hunt, G.L.; Haskins, H.; Heinrich, B.; Sutula, R.

1997-11-01T23:59:59.000Z

231

MTC envelope: defining the capability of large scale computers in the context of parallel scripting applications  

Science Conference Proceedings (OSTI)

Many scientific applications can be efficiently expressed with the parallel scripting (many-task computing, MTC) paradigm. These applications are typically composed of several stages of computation, with tasks in different stages coupled by a shared ... Keywords: MTC, distributed file system, parallel scripting application, performance measurements

Zhao Zhang; Daniel S. Katz; Michael Wilde; Justin M. Wozniak; Ian Foster

2013-06-01T23:59:59.000Z

232

Extended three-dimensional ADCIRC hydrodynamic model to include baroclinic flow and sediment transport  

E-Print Network (OSTI)

The objective of this research is to identify the circulation patterns of the water and sediment fluxes in coastal and estuarine zones, where the shoaling processes correlate with tide generating flow patterns. The research provides a better understanding of the characteristics of spatial and temporal variability of currents. An important deviation from previous research is the inclusion of the baroclinic term, which becomes very important in density driven flows. The understanding of this process provides a basis for determining how the water circulation three-dimensionally controls the hydrodynamics of the system and ultimately transports the suspended and soluble materials due to combined currents and waves. A three-dimensional circulation model is used to calculate the water circulation. The model is based on the three-dimensional (3D) version of Advanced Circulation (AD-CIRC) Hydrodynamic Model with extending the Sediment Transport module. The model is based on the finite element method on unstructured grids. The output of the hydrody-namic model is used to estimate spatial and temporal advections, dispersions and bottom shear stress for the erosion, suspension, deposition and transport of sediment. The model development includes extending the existing three-dimensional (3D) ADCIRC Model with (1) baroclinic forcing term and (2) transport module of suspended and soluble materials. The transport module covers the erosion, material suspension and deposition processes for both cohesive and non-cohesive type sediments. The inclusion of the baroclinic demonstrates the potential of over or underpredicting the total net transport of suspended cohesive sediment under influence of currents. The model provides less than 6% error of theoretical mass conservation for eroded, suspended and deposited sediment material. The inclusion of the baroclinic term in stratified water demonstrates the prevailing longshore sediment transport. It is shown that the model has an application to the transport of the cohesive sediments from the mouth of the Mississippi River along the north shore of the Gulf of Mexico towards and along the Texas coast. The model is also applicable to determine the design erosion thickness of a cap for isolating contaminated dredged material and to evaluate the appro-priate grain size of cap sediments to minimize the erosion.

Pandoe, Wahyu Widodo

2003-05-01T23:59:59.000Z

233

Solar application in Tunisia  

SciTech Connect

Various solar applications were constructed in Tunisia during a program sponsored by the Save the Children Federation. The solar applications were constructed in three community schools, a community wool workshop, a new prototype low income residence, an office, and several residences; solar water heating installations were also built. A modified Trombe wall was constructed partially with metal, thermal mass, and direct gain in a school. The low income residence was equipped with a Trombe wall, a roof overhang, and insulation. Passive solar water heating installations included a mini solar pond and a bottom loading batch water heater. The people and culture of Tunisia are discussed and appropriate technology for the country is reviewed.

Hopman, F.

1979-12-01T23:59:59.000Z

234

Services + Components = Data Intensive Scientific Workflow Applications with MeDICi  

Science Conference Proceedings (OSTI)

Scientific applications are often structured as workflows that execute a series of distributed software modules to analyze large data sets. Such workflows are typically constructed using general-purpose scripting languages to coordinate the execution ... Keywords: components, middleware, services, workflow

Ian Gorton; Jared Chase; Adam Wynne; Justin Almquist; Alan Chappell

2009-06-01T23:59:59.000Z

235

Industrial Applications  

Science Conference Proceedings (OSTI)

Table 2   Frequently used rubber linings in other industries...Application Lining Power industry Scrubber towers Blended chlorobutyl Limestone slurry tanks Blended chlorobutyl Slurry piping Blended chlorobutyl 60 Shore A hardness natural rubber Seawater cooling water

236

Ultrasonics: Fundamentals, Technologies, and Applications  

Science Conference Proceedings (OSTI)

This is a new edition of a bestselling industry reference. Discusses the science, technology, and applications of low and high power ultrasonics, including industrial implementations and medical uses. Reviews the basic equations of acoustics, starting from basic wave equations and their applications. New material on property determination, inspection of metals (NDT) and non-metals, imaging, process monitoring and control. Expanded discussion of transducers, transducer wave-fields, scattering, attenuation and measurement systems and models. New material that discusses high power ultrasonics - in particular using mechanical effects and sonochemistry, including applications to nano-materials. Examines diagnosis, therapy, and surgery from a technology and medical physics perspective.

Ensminger, Dale; Bond, Leonard J.

2011-09-17T23:59:59.000Z

237

SYNTHESIS OF PYRAZINES INCLUDING 2,6-DIAMINOPYRAZINE-1-OXIDE (DAPO ...  

Pagoria, Philip F. (Livermore, CA), Zhang, Mao Xi (Mountain House, CA) Application Number: 12/ 426,774: Filed: April 20, 2009: Government Interests:

238

Reliability evaluation of electric power system including wind power and energy storage .  

E-Print Network (OSTI)

??Global environmental concerns associated with conventional energy generation have led to the rapid growth of wind energy applications in electric power systems. Growing demand for (more)

Hu, Po

2009-01-01T23:59:59.000Z

239

Efficient Evaluation of Doubly Periodic Green Functions in 3D Scattering, Including Wood Anomaly Frequencies  

E-Print Network (OSTI)

We present efficient methods for computing wave scattering by diffraction gratings that exhibit two-dimensional periodicity in three dimensional (3D) space. Applications include scattering in acoustics, electromagnetics and elasticity. Our approach uses boundary-integral equations. The quasi-periodic Green function is a doubly infinite sum of scaled 3D free-space outgoing Helmholtz Green functions. Their source points are located at the nodes of a periodicity lattice of the grating. For efficient numerical computation of the lattice sum, we employ a smooth truncation. Super-algebraic convergence to the Green function is achieved as the truncation radius increases, except at frequency-wavenumber pairs at which a Rayleigh wave is at exactly grazing incidence to the grating. At these "Wood frequencies", the term in the Fourier series representation of the Green function that corresponds to the grazing Rayleigh wave acquires an infinite coefficient and the lattice sum blows up. At Wood frequencies, we modify the Green function by adding two types of terms to it. The first type adds weighted spatial shifts of the Green function to itself with singularities below the grating; this yields algebraic convergence. The second-type terms are quasi-periodic plane wave solutions of the Helmholtz equation. They reinstate (with controlled coefficients) the grazing modes, effectively eliminated by the terms of first type. These modes are needed in the Green function for guaranteeing the well-posedness of the boundary-integral equation that yields the scattered field. We apply this approach to acoustic scattering by a doubly periodic 2D grating near and at Wood frequencies and scattering by a doubly periodic array of scatterers away from Wood frequencies.

Oscar P. Bruno; Stephen P. Shipman; Catalin Turc; Stephanos Venakides

2013-07-04T23:59:59.000Z

240

Corrugated pipe adhesive applicator apparatus  

DOE Patents (OSTI)

Apparatus for coating selected portions of the troughs of a corrugated pipe with an adhesive includes a support disposed within the pipe with a reservoir containing the adhesive disposed on the support. A pump, including a spout, is utilized for supplying the adhesive from the reservoir to a trough of the pipe. A rotatable applicator is supported on the support and contacts the trough of the pipe. The applicator itself is sized so as to fit within the trough, and contacts the adhesive in the trough and spreads the adhesive in the trough upon rotation. A trough shield, supported by the support and disposed in the path of rotation of the applicator, is utilized to prevent the applicator from contacting selected portions of the trough. A locator head is also disposed on the support and provides a way for aligning the spout, the applicator, and the trough shield with the trough. 4 figs.

Shirey, R.A.

1983-06-14T23:59:59.000Z

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Corrugated pipe adhesive applicator apparatus  

DOE Patents (OSTI)

Apparatus for coating selected portions of the troughs of a corrugated pipe within an adhesive includes a support disposed within the pipe with a reservoir containing the adhesive disposed on the support. A pump, including a spout, is utilized for supplying the adhesive from the reservoir to a trough of the pipe. A rotatable applicator is supported on the support and contacts the trough of the pipe. The applicator itself is sized so as to fit within the trough, and contacts the adhesive in the trough and spreads the adhesive in the trough upon rotation. A trough shield, supported by the support and disposed in the path of rotation of the applicator, is utilized to prevent the applicator from contacting selected portions of the trough. A locator head is also disposed on the support and provides a way for aligning the spout, the applicator, and the trough shield with the trough.

Shirey, Ray A. (North Grafton, MA)

1983-06-14T23:59:59.000Z

242

DOE Order 440. 1 B: Worker Protection Program for DOE (Including...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0. 1 B: Worker Protection Program for DOE (Including NNSA) Federal Employees DOE Order 440. 1 B: Worker Protection Program for DOE (Including NNSA) Federal Employees Stakeholders:...

243

NERSC Applications Software  

NLE Websites -- All DOE Office Websites (Extended Search)

For Users Software Applications Applications List of Applications List of math, chemistry and materials science software installed at NERSC. Mathematical Applications...

244

Composite materials and bodies including silicon carbide and titanium diboride and methods of forming same  

DOE Patents (OSTI)

Methods of forming composite materials include coating particles of titanium dioxide with a substance including boron (e.g., boron carbide) and a substance including carbon, and reacting the titanium dioxide with the substance including boron and the substance including carbon to form titanium diboride. The methods may be used to form ceramic composite bodies and materials, such as, for example, a ceramic composite body or material including silicon carbide and titanium diboride. Such bodies and materials may be used as armor bodies and armor materials. Such methods may include forming a green body and sintering the green body to a desirable final density. Green bodies formed in accordance with such methods may include particles comprising titanium dioxide and a coating at least partially covering exterior surfaces thereof, the coating comprising a substance including boron (e.g., boron carbide) and a substance including carbon.

Lillo, Thomas M.; Chu, Henry S.; Harrison, William M.; Bailey, Derek

2013-01-22T23:59:59.000Z

245

Applicant Organization: | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Applicant Organization: Applicant Organization: Applicant Organization: More Documents & Publications BlueFire Ethanol, Inc. Applicant Organization: Applicant Organization:...

246

Impacts of Static Pressure Reset on VAV System Air Leakage, Fan Power and Thermal Energy - Part 2: Case Demonstration for a Typical Climate System  

E-Print Network (OSTI)

In Part 1 of this paper, the theoretical models, integrating the fan airflow, fan head, air leakage factors, are developed to analyze the impacts of the static pressure reset on both pressure dependent and pressure independent terminal boxes. In this part, a simulated air handling unit (AHU) system in Omaha NE is used to demonstrate the energy savings performance in one typical climate year. This AHU system has a static pressure reset system and two constant static pressure systems, one having pressure dependent terminal boxes and one having pressure independent terminal boxes. These simulated systems were compared mainly on the basis of fan power energy consumption and thermal energy consumption in totally a year. The example presents a good agreement with the theoretical model and simulation results. It was also shown that static pressure reset provides a promising and challenging way for the energy performance in VAV system.

Liu, M.; Zheng, K.; Wu, L.; Wang, Z.; Johnson, C.

2007-01-01T23:59:59.000Z

247

Data requirements for intermediate energy nuclear applications  

SciTech Connect

Several applications that include spallation neutron sources, space radiation effects, biomedical isotope production, accelerator shielding and radiation therapy make use of intermediate energy nuclear data extending to several GeV. The overlapping data needs of these applications are discussed in terms of what projectiles, targets and reactions are of interest. Included is a discussion of what is generally known about these data and what is needed to facilitate their use in intermediate energy applications. 40 refs., 2 figs., 2 tabs.

Pearlstein, S.

1990-01-01T23:59:59.000Z

248

Investigation on Electrohydraulic Servovalve through a Finite ...  

Science Conference Proceedings (OSTI)

Typical applications include aerospace, robotic manipulators, motion simulators, injection molding, CNC machines and material testing machines.

249

Remote System Technologies for Deactivating Hanford Hot Cells (for WM'03 - abstract included)  

Science Conference Proceedings (OSTI)

Remote system technologies are being deployed by Fluor Hanford to help accelerate the deactivation of highly-radioactive hot cell facilities. This paper highlights the application of several remotely deployed technologies enabling the deactivation tasks.

BERLIN, G.T.

2003-01-28T23:59:59.000Z

250

DOT Motor-fuel use statistics summary to 1995 The data included...  

Open Energy Info (EERE)

Motor-fuel use statistics summary to 1995 The data included in this submission is United States Department of Transportation (DOT) data up to 1995. The data includes motor-fuel...

251

Molecular Dynamics Model of Ultraviolet Matrix-Assisted Laser Desorption/Ionization Including Ionization Processes  

E-Print Network (OSTI)

Molecular Dynamics Model of Ultraviolet Matrix-Assisted Laser Desorption/Ionization Including A molecular dynamics model of UV-MALDI including ionization processes is presented. In addition/desorption of molecular systems, it includes radiative and nonradiative decay, exciton hopping, two pooling processes

Zhigilei, Leonid V.

252

Ridefinders Application  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

23 23 (05-92) Ridefinders Application Please submit this application to the U.S. Department of Energy (DOE) Employee Transportation Coordinator, Room 7A-156, Forrestal. U.S. Department of Energy Privacy Act Statement Check all transportation options which interest you: Carpool: Driver Share Driving Rider Vanpool: Driver Share Driving Rider Do you wish to meet your pool in your neighborhood? No (If no, see Alternate Pickup Locations below.) Yes Participation in the Federal Facility Ridesharing Program is voluntary and a private accommodation of employees rather than a Federal activity. Ridefinders Network will observe Privacy Act requirements because participation requires solicitation of personal information. The information collected will be used to maintain an accurate database of those individuals participating in the program and to provide individual ridematch lists

253

The Edwards School of Business is once again taking proposals for consulting projects to be completed by MBA students. Accepted projects will cost $2,500 depending on scope, plus expenses, which typically run between $500  

E-Print Network (OSTI)

to be completed by MBA students. Accepted projects will cost $2,500 depending on scope, plus expenses, whichThe Edwards School of Business is once again taking proposals for consulting projects typically run between $500 and $1,000. Though you are not limited to these, typically projects fall within

Saskatchewan, University of

254

Photovoltaic Device Including A Boron Doping Profile In An I-Type Layer  

DOE Patents (OSTI)

A photovoltaic cell for use in a single junction or multijunction photovoltaic device, which includes a p-type layer of a semiconductor compound including silicon, an i-type layer of an amorphous semiconductor compound including silicon, and an n-type layer of a semiconductor compound including silicon formed on the i-type layer. The i-type layer including an undoped first sublayer formed on the p-type layer, and a boron-doped second sublayer formed on the first sublayer.

Yang, Liyou (Lawrenceville, NJ)

1993-10-26T23:59:59.000Z

255

Topology, Design, Analysis, and Thermal Management of Power Electronics for Hybrid Electric Vehicle Applications  

DOE Green Energy (OSTI)

Power electronics circuits play an important role in the success of electric, hybrid and fuel cell vehicles. Typical power electronics circuits in hybrid vehicles include electric motor drive circuits and DC/DC converter circuits. Conventional circuit topologies, such as buck converters, voltage source inverters and bidirectional boost converters are challenged by system cost, efficiency, controllability, thermal management, voltage and current capability, and packaging issues. Novel topologies, such as isolated bidirectional DC/DC converters, multilevel converters, and Z-source inverters, offer potential improvement to hybrid vehicle system performance, extended controllability and power capabilities. This paper gives an overview of the topologies, design, and thermal management, and control of power electronics circuits in hybrid vehicle applications.

Mi, C.; Peng, F. Z.; Kelly, K. J.; O'Keefe, M.; Hassani, V.

2008-01-01T23:59:59.000Z

256

Digital control systems in nuclear power plants: Failure information, modeling concepts, and applications. Revision 1  

SciTech Connect

This report briefly describes some current applications of advanced computerized digital display and control systems at US commercial nuclear power plants and presents the results of a literature search that was made to gather information on the reliability of these systems. Both hardware and software reliability were addressed in this review. Only limited failure rate information was found, with the chemical process industry being the primary source of information on hardware failure rates and expert opinion the primary source for software failure rates. Safety-grade digital control systems are typically installed on a functional like-for-like basis, replacing older analog systems without substantially changing interactions with other plant systems. Future work includes performing a limited probabilistic risk assessment of a representative DCS to assess its risk significance.

Galyean, W.J.

1993-06-23T23:59:59.000Z

257

Wireless Power May Cut the Cord for Plug-In Devices, Including Cars1 by Will Ferguson for National Geographic News, abbreviated2  

E-Print Network (OSTI)

Wireless Power May Cut the Cord for Plug-In Devices, Including Cars1 by Will Ferguson for National no power cord, a car fueled by a cordless panel in the floor:4 In a nondescript building just outside Boston, these and other applications of wireless electricity signal a future with fewer snaking5 cables.6

South Bohemia, University of

258

Battery Life Prediction Method for Hybrid Power Applications: Preprint  

Science Conference Proceedings (OSTI)

Batteries in hybrid power applications that include intermittent generators, such as wind turbines, experience a very irregular pattern of charge and discharge cycles. Because battery life is dependent on both depth and rate of discharge (and other factors such as temperature, charging strategy, etc.), estimating battery life and optimally sizing batteries for hybrid systems is difficult. Typically, manufacturers give battery life data, if at all, as cycles to failure versus depth of discharge, where all discharge cycles are assumed to be under conditions of constant temperature, current, and depth of discharge. Use of such information directly can lead to gross errors in battery lifetime estimation under actual operating conditions, which may result in either a higher system cost than necessary or an undersized battery bank prone to early failure. Even so, most current battery life estimation algorithms consider only the effect of depth of discharge on cycle life. This paper will discuss a new battery life prediction method, developed to investigate the effects of two primary determinants of battery life in hybrid power applications, varying depths of discharge and varying rates of discharge. A significant feature of the model is that it bases its analysis on battery performance and cycle life data provided by the manufacturer, supplemented by a limited amount of empirical test data, eliminating the need for an electrochemical model of the battery. It performs the analysis for a user-prescribed discharge profile consisting of a series of discharge events of specified average current and duration. Sample analyses are presented to show how the method can be used to select the most economical battery type and size for a given hybrid power system application.

Drouilhet, S.; Johnson, B. L.

1997-01-01T23:59:59.000Z

259

DOE Order 440. 1 B: Worker Protection Program for DOE (Including NNSA)  

NLE Websites -- All DOE Office Websites (Extended Search)

0. 1 B: Worker Protection Program for DOE (Including 0. 1 B: Worker Protection Program for DOE (Including NNSA) Federal Employees DOE Order 440. 1 B: Worker Protection Program for DOE (Including NNSA) Federal Employees Stakeholders: DOE and NNSA employees Scope: DOE Order 440.1 B establishes the framework for an effective worker protection program that will reduce or prevent injuries, illnesses, and accidental losses by providing Department of Energy, including National Nuclear Security Administration (NNSA), Federal workers with a safe and healthful workplace. Summary: Among the requirements of DOE Order 440.1 B, the Department must provide its employees, including NNSA, a number of protections relating to whistle blowing guidelines. The relevant section of requirements includes: 4. REQUIREMENTS. DOE elements must:

260

Photovoltaic module kit including connector assembly for non-penetrating array installation  

Science Conference Proceedings (OSTI)

A PV module kit for non-penetrating rooftop installation, including a plurality of PV modules and a plurality of connectors. Each of the PV modules includes a PV laminate and a frame forming a mounting region assembled thereto. The connectors include a male connector having a male fastener extending from a head, and a female connector having a female fastener assembled within a head. The heads are entirely formed of plastic. The kit provides a mounted array state including a junction at which the mounting region of at least two of the PV modules are aligned and interconnected by engagement of the male connector with the female connector. The so-formed junction is substantially electrically insulated. The plurality of connectors can further include a spacer connector including a head forming a bore sized to slidably receive the male fastener, with all of the connector heads being identical.

Botkin, Jonathan (El Cerrito, CA); Graves, Simon (Berkeley, CA); Danning, Matt (Oakland, CA); Culligan, Matthew (Berkeley, CA)

2011-11-22T23:59:59.000Z

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Photovoltaic module kit including connector assembly for non-penetrating array installation  

DOE Patents (OSTI)

A PV module kit for non-penetrating rooftop installation, including a plurality of PV modules and a plurality of connectors. Each of the PV modules includes a PV laminate and a frame forming a mounting region assembled thereto. The connectors include a male connector having a male fastener extending from a head, and a female connector having a female fastener assembled within a head. The heads are entirely formed of plastic. The kit provides a mounted array state including a junction at which the mounting region of at least two of the PV modules are aligned and interconnected by engagement of the male connector with the female connector. The so-formed junction is substantially electrically insulated. The plurality of connectors can further include a spacer connector including a head forming a bore sized to slidably receive the male fastener, with all of the connector heads being identical.

Botkin, Jonathan; Graves, Simon; Danning, Matt; Culligan, Matthew

2012-10-23T23:59:59.000Z

262

NREL/Ventyx Utility Rates: What is included? | OpenEI Community  

Open Energy Info (EERE)

NREL/Ventyx Utility Rates: What is included? NREL/Ventyx Utility Rates: What is included? Home > Groups > Utility Rate Does anyone know what pieces of electric rates are included in the NREL/Ventyx database of rates by utility, i.e. is it supply only or does the file include supply, transmission & distribution costs? Thanks! Submitted by Vbugnion on 27 February, 2013 - 16:25 1 answer Points: 1 Hi Vbugnion, Just to clarify, you're not asking about the OpenEI utility rates, but rather the Ventyx rates found here: http://developer.nrel.gov/doc/api/georeserv/service/utility_rates If so, then the Ventyx rates do include all bundled rates (which includes supply, trans, and distr costs). However, there's a small but non-zero possibility that a few energy-only or delivery-only rates may not have been cleaned

263

Multi-objective design and optimization of district energy systems including polygeneration energy conversion technologies.  

E-Print Network (OSTI)

??In the present context of finding ways to decrease CO2 emissions linked with human activity, district energy systems including polygeneration energy conversion technologies are likely (more)

Weber, Cline Isabelle

2008-01-01T23:59:59.000Z

264

Petroleum Gasoline & Distillate Needs Including the Energy Independence and Security Act (EISA) Impacts  

Reports and Publications (EIA)

This presentation describes the projections for petroleum-based gasoline and distillate in the Update AEO 2008, which includes the impacts of the Energy Independence and Security Act.

Information Center

2008-03-11T23:59:59.000Z

265

ORISE: REAC/TS Symposium to include sessions on the Fukushima...  

NLE Websites -- All DOE Office Websites (Extended Search)

MEDIA ADVISORY: REACTS International Symposium to include sessions on the Fukushima crisis FOR IMMEDIATE RELEASE Aug. 31, 2011 FY11-42 Who: Radiation Emergency Assistance Center...

266

Comparative chloroplast genomics: Analyses including new sequences from the angiosperms Nuphar advena and Ranunculus macranthus  

E-Print Network (OSTI)

to other angiosperms. BMC Genomics 2006, 7:61. 20.history of chloroplast genomics. Photosynth Res 2003, 76:Comparative chloroplast genomics: Analyses including new

2007-01-01T23:59:59.000Z

267

Fast and Accurate Simulation of Biomonitoring Applications on a Wireless Body Area Network  

E-Print Network (OSTI)

to calculate the energy consumption. 2) Simulator Accuracy: To compare the measured and simulated power usage that the BAN simulator can predict the energy usage of the application rather accurately. In addition (BAN) provide a convenient platform for health monitoring. A typical biomonitoring application running

Plotkin, Joshua B.

268

Multi-Criteria Scheduling of Pipeline Workflows (and Application To the JPEG Encoder)  

Science Conference Proceedings (OSTI)

Mapping workflow applications onto parallel platforms is a challenging problem, even for simple application patterns such as pipeline graphs. Several antagonist criteria should be optimized, such as throughput and latency (or a combination). A typical ... Keywords: JPEG encode pipeline, algorithmic skeletons, complexity results, heterogeneous platforms, heuristics, multi-criteria optimization, pipeline

Anne Benoit; Harald Kosch; Veronika Rehn-Sonigo; Yves Robert

2009-05-01T23:59:59.000Z

269

PPasteurized (Includes provisions from the Grade "A" Condensed and Dry Milk Products  

E-Print Network (OSTI)

control legislation; and to encourage the application of uniform enforcement procedures through for information or advice on proper legal procedures, such as the recording and advertising of the Ordinance after unenforceable. In order to promote uniformity, it is recommended that all of the Administrative Procedures

Keinan, Alon

270

FINANCIAL AID Financial Aid programs, including scholarships, grants, loans, and work-study, will be  

E-Print Network (OSTI)

available to students. All financial aid programs will adhere to the guidelines, procedures and standards of the funding agency and will incorporate federal, state and other applicable regulatory requirements. The Superintendent/President shall assure that satisfactory academic progress standards for all participants in Title IV of the Higher Education Act are established, publicized and applied. Reference:

unknown authors

2002-01-01T23:59:59.000Z

271

PRA insights applicable to the design of the Broad Applications Test Reactor  

SciTech Connect

Design insights applicable to the design of a new Broad Applications Test Reactor (BATR), being studied at Idaho National Engineering Laboratory, are summarized. Sources of design insights include past probabilistic risk assessments and related studies for department of Energy-owned Class A reactors and for commercial reactors. The report includes a preliminary risk allocation scheme for the BATR.

Khericha, S.T.; Reilly, H.J.

1993-01-01T23:59:59.000Z

272

Property:Number of Plants Included in Planned Estimate | Open Energy  

Open Energy Info (EERE)

Plants Included in Planned Estimate Plants Included in Planned Estimate Jump to: navigation, search Property Name Number of Plants Included in Planned Estimate Property Type String Description Number of plants included in the estimate of planned capacity per GEA Pages using the property "Number of Plants Included in Planned Estimate" Showing 21 pages using this property. A Alaska Geothermal Region + 3 + C Cascades Geothermal Region + 1 + Central Nevada Seismic Zone Geothermal Region + 4 + G Gulf of California Rift Zone Geothermal Region + 7 + H Hawaii Geothermal Region + 1 + Holocene Magmatic Geothermal Region + 4 + I Idaho Batholith Geothermal Region + 1 + N Northern Basin and Range Geothermal Region + 9 + Northern Rockies Geothermal Region + 0 + Northwest Basin and Range Geothermal Region + 6 +

273

Systems including catalysts in porous zeolite materials within a reactor for use in synthesizing hydrocarbons  

Science Conference Proceedings (OSTI)

Catalytic structures include a catalytic material disposed within a zeolite material. The catalytic material may be capable of catalyzing a formation of methanol from carbon monoxide and/or carbon dioxide, and the zeolite material may be capable of catalyzing a formation of hydrocarbon molecules from methanol. The catalytic material may include copper and zinc oxide. The zeolite material may include a first plurality of pores substantially defined by a crystal structure of the zeolite material and a second plurality of pores dispersed throughout the zeolite material. Systems for synthesizing hydrocarbon molecules also include catalytic structures. Methods for synthesizing hydrocarbon molecules include contacting hydrogen and at least one of carbon monoxide and carbon dioxide with such catalytic structures. Catalytic structures are fabricated by forming a zeolite material at least partially around a template structure, removing the template structure, and introducing a catalytic material into the zeolite material.

Rolllins, Harry W. (Idaho Falls, ID); Petkovic, Lucia M. (Idaho Falls, ID); Ginosar, Daniel M. (Idaho Falls, ID)

2012-07-24T23:59:59.000Z

274

Systems and strippable coatings for decontaminating structures that include porous material  

SciTech Connect

Methods of removing contaminant matter from porous materials include applying a polymer material to a contaminated surface, irradiating the contaminated surface to cause redistribution of contaminant matter, and removing at least a portion of the polymer material from the surface. Systems for decontaminating a contaminated structure comprising porous material include a radiation device configured to emit electromagnetic radiation toward a surface of a structure, and at least one spray device configured to apply a capture material onto the surface of the structure. Polymer materials that can be used in such methods and systems include polyphosphazine-based polymer materials having polyphosphazine backbone segments and side chain groups that include selected functional groups. The selected functional groups may include iminos, oximes, carboxylates, sulfonates, .beta.-diketones, phosphine sulfides, phosphates, phosphites, phosphonates, phosphinates, phosphine oxides, monothio phosphinic acids, and dithio phosphinic acids.

Fox, Robert V. (Idaho Falls, ID); Avci, Recep (Bozeman, MT); Groenewold, Gary S. (Idaho Falls, ID)

2011-12-06T23:59:59.000Z

275

Physical and Chemical Applications  

NLE Websites -- All DOE Office Websites (Extended Search)

data image data image Physical and Chemical Applications Research in this area includes: Chemical analysis (femtosecond laser ablation). Advanced sensors (laser ultrasonics). Advanced materials and nanotechnology for clean energy- hydrogen storage, nanostructured organic light-emitting diodes, nanowires, and nanoparticles). Photons to fuels (biosynthetic pathways for generating hydrocarbon biofuels in photosynthetic organisms). Advanced Sensor Development Sensor-based control of industrial processes can help companies: Decrease production costs; Reduce waste of raw materials on manufacturing lines; Lower manufacturing downtime from equipment maintenance; Increase the energy efficiency of manufacturing processes; Detect equipment failure early, before it becomes a major liability;

276

Non-personnel OMB A-21 Exceptions Direct Charging to Federal Projects Direct charging costs to federal grants which are typically considered F&A may be  

E-Print Network (OSTI)

are met. These conditions include: 1. items are required by the projects scope of work 2. costs can be specifically and easily identified to this project 3. the number and/or cost of the items needed is clearly use on a project, charges may be allowable as direct costs if appropriately justified. Office supplies

Hall, Daniel

277

Assessment of instrumentation needs for advanced coal power plant applications: Final report  

DOE Green Energy (OSTI)

The purpose of this study was to identify contaminants, identify instrumentation needs, assess available instrumentation and identify instruments that should be developed for controlling and monitoring gas streams encountered in the following power plants: Integrated Gasification Combined Cycle, Pressurized Fluidized Bed Combustion, and Gasification Molten Carbonate Fuel Cell. Emphasis was placed on hot gas cleanup system gas stream analysis, and included process control, research and environmental monitoring needs. Commercial process analyzers, typical of those currently used for process control purposes, were reviewed for the purpose of indicating commercial status. No instrument selection guidelines were found which were capable of replacing user interaction with the process analyzer vendors. This study leads to the following conclusions: available process analyzers for coal-derived gas cleanup applications satisfy current power system process control and regulatory requirements, but they are troublesome to maintain; commercial gas conditioning systems and in situ analyzers continue to be unavailable for hot gas cleanup applications; many research-oriented gas stream characterization and toxicity assessment needs can not be met by commercially available process analyzers; and greater emphasis should be placed on instrumentation and control system planning for future power plant applications. Analyzers for specific compounds are not recommended other than those needed for current process control purposes. Instead, some generally useful on-line laser-based and inductively coupled plasma methods are recommended for further development because of their potential for use in present hot gas cleanup research and future optimization, component protection and regulation compliance activities. 48 refs., 21 figs., 26 tabs.

Nelson, E.T.; Fischer, W.H.; Lipka, J.V.; Rutkowski, M.D.; Zaharchuk, R.

1987-10-01T23:59:59.000Z

278

NIST Laser Applications Group Homepage  

Science Conference Proceedings (OSTI)

Laser Applications Group. Welcome. The Laser Applications Group advances laser technology for applications in optical ...

2012-05-10T23:59:59.000Z

279

Initial Business Case Analysis of Two Integrated Heat Pump HVAC Systems for Near-Zero-Energy Homes - Update to Include Evaluation of Impact of Including a Humidifier Option  

SciTech Connect

The long range strategic goal of the Department of Energy's Building Technologies (DOE/BT) Program is to create, by 2020, technologies and design approaches that enable the construction of net-zero energy homes at low incremental cost (DOE/BT 2005). A net zero energy home (NZEH) is a residential building with greatly reduced needs for energy through efficiency gains, with the balance of energy needs supplied by renewable technologies. While initially focused on new construction, these technologies and design approaches are intended to have application to buildings constructed before 2020 as well resulting in substantial reduction in energy use for all building types and ages. DOE/BT's Emerging Technologies (ET) team is working to support this strategic goal by identifying and developing advanced heating, ventilating, air-conditioning, and water heating (HVAC/WH) technology options applicable to NZEHs. In FY05 ORNL conducted an initial Stage 1 (Applied Research) scoping assessment of HVAC/WH systems options for future NZEHs to help DOE/BT identify and prioritize alternative approaches for further development. Eleven system concepts with central air distribution ducting and nine multi-zone systems were selected and their annual and peak demand performance estimated for five locations: Atlanta (mixed-humid), Houston (hot-humid), Phoenix (hot-dry), San Francisco (marine), and Chicago (cold). Performance was estimated by simulating the systems using the TRNSYS simulation engine (Solar Energy Laboratory et al. 2006) in two 1800-ft{sup 2} houses--a Building America (BA) benchmark house and a prototype NZEH taken from BEopt results at the take-off (or crossover) point (i.e., a house incorporating those design features such that further progress towards ZEH is through the addition of photovoltaic power sources, as determined by current BEopt analyses conducted by NREL). Results were summarized in a project report, HVAC Equipment Design options for Near-Zero-Energy Homes--A Stage 2 Scoping Assessment, ORNL/TM-2005/194 (Baxter 2005). The 2005 study report describes the HVAC options considered, the ranking criteria used, and the system rankings by priority. In 2006, the two top-ranked options from the 2005 study, air-source and ground-source versions of a centrally ducted integrated heat pump (IHP) system, were subjected to an initial business case study. The IHPs were subjected to a more rigorous hourly-based assessment of their performance potential compared to a baseline suite of equipment of legally minimum efficiency that provided the same heating, cooling, water heating, demand dehumidification, and ventilation services as the IHPs. Results were summarized in a project report, Initial Business Case Analysis of Two Integrated Heat Pump HVAC Systems for Near-Zero-Energy Homes, ORNL/TM-2006/130 (Baxter 2006a). The present report is an update to that document which summarizes results of an analysis of the impact of adding a humidifier to the HVAC system to maintain minimum levels of space relative humidity (RH) in winter. The space RH in winter has direct impact on occupant comfort and on control of dust mites, many types of disease bacteria, and 'dry air' electric shocks. Chapter 8 in ASHRAE's 2005 Handbook of Fundamentals (HOF) suggests a 30% lower limit on RH for indoor temperatures in the range of {approx}68-69F based on comfort (ASHRAE 2005). Table 3 in chapter 9 of the same reference suggests a 30-55% RH range for winter as established by a Canadian study of exposure limits for residential indoor environments (EHD 1987). Harriman, et al (2001) note that for RH levels of 35% or higher, electrostatic shocks are minimized and that dust mites cannot live at RH levels below 40%. They also indicate that many disease bacteria life spans are minimized when space RH is held within a 30-60% range. From the foregoing it is reasonable to assume that a winter space RH range of 30-40% would be an acceptable compromise between comfort considerations and limitation of growth rates for dust mites and many bacteria. In addition it reports som

Baxter, Van D [ORNL

2007-02-01T23:59:59.000Z

280

Standard Test Method for Application and Analysis of Solid State Track Recorder (SSTR) Monitors for Reactor Surveillance, E706(IIIB)  

E-Print Network (OSTI)

1.1 This test method describes the use of solid-state track recorders (SSTRs) for neutron dosimetry in light-water reactor (LWR) applications. These applications extend from low neutron fluence to high neutron fluence, including high power pressure vessel surveillance and test reactor irradiations as well as low power benchmark field measurement. (1) This test method replaces Method E 418. This test method is more detailed and special attention is given to the use of state-of-the-art manual and automated track counting methods to attain high absolute accuracies. In-situ dosimetry in actual high fluence-high temperature LWR applications is emphasized. 1.2 This test method includes SSTR analysis by both manual and automated methods. To attain a desired accuracy, the track scanning method selected places limits on the allowable track density. Typically good results are obtained in the range of 5 to 800 000 tracks/cm2 and accurate results at higher track densities have been demonstrated for some cases. (2) Trac...

American Society for Testing and Materials. Philadelphia

2003-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Inducing Order from Disordered Copolymers: On Demand Generation of Triblock Morphologies Including Networks  

Science Conference Proceedings (OSTI)

Disordered block copolymers are generally impractical in nanopatterning applications due to their inability to self-assemble into well-defined nanostructures. However, inducing order in low molecular weight disordered systems permits the design of periodic structures with smaller characteristic sizes. Here, we have induced nanoscale phase separation from disordered triblock copolymer melts to form well-ordered lamellae, hexagonally packed cylinders, and a triply periodic gyroid network structure, using a copolymer/homopolymer blending approach, which incorporates constituent homopolymers into selective block domains. This versatile blending approach allows one to precisely target multiple nanostructures from a single disordered material and can be applied to a wide variety of triblock copolymer systems for nanotemplating and nanoscale separation applications requiring nanoscale feature sizes and/or high areal feature densities.

Tureau, Mava S.; Kuan, Wei-Fan; Rong, Lixia; Hsiao, Benjamin S.; Epps, III, Thomas H. (Delaware); (SUNYB)

2012-10-26T23:59:59.000Z

282

Energy Department Expands Gas Gouging Reporting System to Include 1-800  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Expands Gas Gouging Reporting System to Include Expands Gas Gouging Reporting System to Include 1-800 Number: 1-800-244-3301 Energy Department Expands Gas Gouging Reporting System to Include 1-800 Number: 1-800-244-3301 September 6, 2005 - 9:50am Addthis Washington, DC - Energy Secretary Samuel W. Bodman announced today that the Department of Energy has expanded its gas gouging reporting system to include a toll-free telephone hotline. The hotline is available to American consumers starting today. "While we've largely seen the best of American generosity and unity throughout the recovery effort, we recognize that there are some bad actors that may try to take advantage of the situation. Consumers are our first line of defense in guarding against gas price gouging. I can assure you, our Administration - from the President down - takes this issue very

283

RECOMMENDATIONS TO INCLUDE IN CALIFORNIA ENERGY COMMISSION'S 2009 INTEGRATED ENERGY POLICY REPORT (IEPR)  

E-Print Network (OSTI)

RECOMMENDATIONS TO INCLUDE IN CALIFORNIA ENERGY COMMISSION'S 2009 INTEGRATED ENERGY POLICY REPORT solutions. Overview Past Energy Commission Integrated Energy Policy Reports (IEPRs) have recognized (IEPR) Submitted By: Steven Weissman Associate Director Center for Law, Energy and the Environment

Kammen, Daniel M.

284

On a Three Step Model of Anaerobic Digestion Including the Hydrolysis of  

E-Print Network (OSTI)

On a Three Step Model of Anaerobic Digestion Including the Hydrolysis of Particulate Matter R degradation, chemostat, models, growth rate, equilibrium, bistability. 1. INTRODUCTION Anaerobic digestion, the anaerobic digestion is generally considered as a three step process: hydrolysis and liquefaction

Paris-Sud XI, Université de

285

Numerical simulation of ECRIPAC plasma behaviour with Vlasov equations including electron and ion collective effects  

E-Print Network (OSTI)

976 Numerical simulation of ECRIPAC plasma behaviour with Vlasov equations including electron of 4 MeV energy with very short pulses. (`ompared to ISlectron Ring Accelerators, ECRIPAC presents

Paris-Sud XI, Université de

286

Automated solar collector installation design including ability to define heterogeneous design preferences  

DOE Patents (OSTI)

Embodiments may include systems and methods to create and edit a representation of a worksite, to create various data objects, to classify such objects as various types of pre-defined "features" with attendant properties and layout constraints. As part of or in addition to classification, an embodiment may include systems and methods to create, associate, and edit intrinsic and extrinsic properties to these objects. A design engine may apply of design rules to the features described above to generate one or more solar collectors installation design alternatives, including generation of on-screen and/or paper representations of the physical layout or arrangement of the one or more design alternatives. Embodiments may also include definition of one or more design apertures, each of which may correspond to boundaries in which solar collector layouts should comply with distinct sets of user-defined design preferences. Distinct apertures may provide heterogeneous regions of collector layout according to the user-defined design preferences.

Wayne, Gary; Frumkin, Alexander; Zaydman, Michael; Lehman, Scott; Brenner, Jules

2013-01-08T23:59:59.000Z

287

Code Thrust 1400 Aeronautical/Astronautical Engineering (including Aerodynamics, Aerospace Engineering, and Space Technology)  

E-Print Network (OSTI)

Sciences (including Clinical/Medical Laboratory Technologies, Communication Disorders Sciences and Services, Gerontology, Health and Medical Administrative Services, Other Health Professions and Related Services, Environmental health, Geotechnical, Hydraulic, Hydrologic, Sanitary, Structural, and Transportation) 1404

Alabama in Huntsville, University of

288

Light reflecting apparatus including a multi-aberration light reflecting surface  

DOE Patents (OSTI)

A light reflecting apparatus including a multi-aberration bendable light reflecting surface is disclosed herein. This apparatus includes a structural assembly comprised of a rectangular plate which is resiliently bendable, to a limited extent, and which has a front side defining the multi-aberration light reflecting surface and an opposite back side, and a plurality of straight leg members rigidly connected with the back side of the plate and extending rearwardly therefrom. The apparatus also includes a number of different adjustment mechanisms, each of which is connected with specific ones of the leg members. These mechanisms are adjustably movable in different ways for applying corresponding forces to the leg members in order to bend the rectangular plate and light reflecting surface into different predetermined curvatures and which specifically include quadratic and cubic curvatures corresponding to different optical aberrations.

Sawicki, Richard H. (Pleasanton, CA); Sweatt, William (Livermore, CA)

1987-01-01T23:59:59.000Z

289

Modification of the Khler Equation to Include Soluble Trace Gases and Slightly Soluble Substances  

Science Conference Proceedings (OSTI)

A generalized reformulation of the Khler theory to include the effect of soluble gases and slightly soluble aerosol substances is presented. A single equation is derived that takes into account 1) the Kelvin effect; 2) the Raoult effect caused ...

Ari Laaksonen; Pekka Korhonen; Markku Kulmala; Robert J. Charlson

1998-03-01T23:59:59.000Z

290

A New Bulk Microphysical Scheme That Includes Riming Intensity and Temperature-Dependent Ice Characteristics  

Science Conference Proceedings (OSTI)

A new bulk microphysical parameterization (BMP) scheme is presented that includes a diagnosed riming intensity and its impact on ice characteristics. As a result, the new scheme represents a continuous spectrum from pristine ice particles to ...

Yanluan Lin; Brian A. Colle

2011-03-01T23:59:59.000Z

291

Modeling and Controller Design of a Wind Energy Conversion System Including a Matrix Converter.  

E-Print Network (OSTI)

??In this thesis, a grid-connected wind-energy converter system including a matrix converter is proposed. The matrix converter, as a power electronic converter, is used to (more)

Barakati, Seyed Masoud

2008-01-01T23:59:59.000Z

292

Including Surface Kinetic Effects in Simple Models of Ice Vapor Diffusion  

Science Conference Proceedings (OSTI)

A model for kinetically-limited vapor growth and aspect ratio evolution of atmospheric single ice crystals is presented. The method is based on the adaptive habit model of Chen and Lamb (1994), but is modified to include the deposition ...

Chengzhu Zhang; Jerry Y. Harrington

293

A Simple Model of Abyssal Circulation, Including Effects of Wind, Buoyancy and Topography  

Science Conference Proceedings (OSTI)

We examine problems of steady abyssal circulation using an inviscid planetary geostrophic layered model. The model includes an active wind-driven upper layer and arbitrary topography; forcing is in the form of specified interlayer mass fluxes ...

Susan L. Hautala; Stephen C. Riser

1989-05-01T23:59:59.000Z

294

Options for Removing Multiple Pollutants Including CO2 at Existing Coal-Fired Power Plants  

Science Conference Proceedings (OSTI)

This report is a technical review of the fuel changes and technology options for existing coal-fired power plants in response to potential new requirements for increasingly stringent multi-pollutant air emissions reductions, possibly including carbon dioxide (CO2). Preliminary costing of the major options is included. A database of the U.S. coal-fired power plants has been developed for further, more specific analyses.

2002-10-08T23:59:59.000Z

295

Heat Pipes: An Industrial Application  

E-Print Network (OSTI)

This paper reviews the basics of heat pipe exchangers. Included are how they are constructed, how they operate, where they have application, and various aspects of evaluating a potential application. After discussing the technical aspects of heat pipe exchangers, an industrial case history is presented. The case history involves a retrofit project which added heat pipes to five natural draft process heaters with a combined heat duty of 150 M Btu/hr. A heat recovery of 15 M Btu/hr has resulted from the flue gas/combustion air interchange. The paper will include design considerations, and operating and maintenance history since early 1980. A second application for heat pipes with a 12 M Btu/hr duty installed in 1983 will also be discussed.

Murray, F.

1984-01-01T23:59:59.000Z

296

FieldOffice Project # Applicant  

E-Print Network (OSTI)

....................................................................................106 Appendix F: Solar Thermal and Photovoltaic (PV) Applications for Site Operations at Tuba City, Arizona and technologies addressed in the report include concentrating solar power (CSP), photovoltaics (PV), and wind-plate, Nonconcentrating PV Systems In a fixed flat-plate, nonconcentrating PV system, the solar modules are fixed so

Laughlin, Robert B.

297

Biobased Surfactants and Detergents: Synthesis, Properties, and Applications  

Science Conference Proceedings (OSTI)

This must-have book covers biosurfactants: synthesis and applications. Contents include how to reduce manufacturing and purification costs, impurities, and by-products. Biobased Surfactants and Detergents: Synthesis, Properties, and Applications Hardback

298

Fuel cell market applications  

DOE Green Energy (OSTI)

This is a review of the US (and international) fuel cell development for the stationary power generation market. Besides DOE, GRI, and EPRI sponsorship, the US fuel cell program has over 40% cost-sharing from the private sector. Support is provided by user groups with over 75 utility and other end-user members. Objectives are to develop and demonstrate cost-effective fuel cell power generation which can initially be commercialized into various market applications using natural gas fuel by the year 2000. Types of fuel cells being developed include PAFC (phosphoric acid), MCFC (molten carbonate), and SOFC (solid oxide); status of each is reported. Potential international applications are reviewed also. Fuel cells are viewed as a force in dispersed power generation, distributed power, cogeneration, and deregulated industry. Specific fuel cell attributes are discussed: Fuel cells promise to be one of the most reliable power sources; they are now being used in critical uninterruptible power systems. They need hydrogen which can be generated internally from natural gas, coal gas, methanol landfill gas, or other fuels containing hydrocarbons. Finally, fuel cell development and market applications in Japan are reviewed briefly.

Williams, M.C.

1995-12-31T23:59:59.000Z

299

Development of Low Cost Sensors for Hydrogen Safety Applications  

SciTech Connect

We are developing rugged and reliable hydrogen safety sensors that can be easily manufactured. Potential applications also require an inexpensive sensor that can be easily deployed. Automotive applications demand low cost, while personnel safety applications emphasize light-weight, battery-operated, and wearable sensors. Our current efforts involve developing and optimizing sensor materials for stability and compatibility with typical thick-film manufacturing processes. We are also tailoring the sensor design and size along with various packaging and communication schemes for optimal acceptance by end users.

Hoffheins, B.S.; Holmes, W., Jr.; Lauf, R.J.; Maxey, L.C.; Salter, C.; Walker, D.

1999-04-07T23:59:59.000Z

300

Surety applications in transportation  

Science Conference Proceedings (OSTI)

Infrastructure surety can make a valuable contribution to the transportation engineering industry. The lessons learned at Sandia National Laboratories in developing surety principles and technologies for the nuclear weapons complex and the nuclear power industry hold direct applications to the safety, security, and reliability of the critical infrastructure. This presentation introduces the concepts of infrastructure surety, including identification of the normal, abnormal, and malevolent threats to the transportation infrastructure. National problems are identified and examples of failures and successes in response to environmental loads and other structural and systemic vulnerabilities are presented. The infrastructure surety principles developed at Sandia National Laboratories are described. Currently available technologies including (a) three-dimensional computer-assisted drawing packages interactively combined with virtual reality systems, (b) the complex calculational and computational modeling and code-coupling capabilities associated with the new generation of supercomputers, and (c) risk-management methodologies with application to solving the national problems associated with threats to the critical transportation infrastructure are discussed.

Matalucci, R.V.; Miyoshi, D.S.

1998-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

The Human Bathtub: Safety and Risk Predictions Including the Dynamic Probability of Operator Errors  

SciTech Connect

Reactor safety and risk are dominated by the potential and major contribution for human error in the design, operation, control, management, regulation and maintenance of the plant, and hence to all accidents. Given the possibility of accidents and errors, now we need to determine the outcome (error) probability, or the chance of failure. Conventionally, reliability engineering is associated with the failure rate of components, or systems, or mechanisms, not of human beings in and interacting with a technological system. The probability of failure requires a prior knowledge of the total number of outcomes, which for any predictive purposes we do not know or have. Analysis of failure rates due to human error and the rate of learning allow a new determination of the dynamic human error rate in technological systems, consistent with and derived from the available world data. The basis for the analysis is the 'learning hypothesis' that humans learn from experience, and consequently the accumulated experience defines the failure rate. A new 'best' equation has been derived for the human error, outcome or failure rate, which allows for calculation and prediction of the probability of human error. We also provide comparisons to the empirical Weibull parameter fitting used in and by conventional reliability engineering and probabilistic safety analysis methods. These new analyses show that arbitrary Weibull fitting parameters and typical empirical hazard function techniques cannot be used to predict the dynamics of human errors and outcomes in the presence of learning. Comparisons of these new insights show agreement with human error data from the world's commercial airlines, the two shuttle failures, and from nuclear plant operator actions and transient control behavior observed in transients in both plants and simulators. The results demonstrate that the human error probability (HEP) is dynamic, and that it may be predicted using the learning hypothesis and the minimum failure rate, and can be utilized for probabilistic risk analysis purposes. (authors)

Duffey, Romney B. [Atomic Energy of Canada, Ltd., 2251 Speakman Drive, Mississauga, ON, L5K 1B2 (Canada); Saull, John W. [International Federation of Airwothiness, 14 Railway Approach, East Grinstead, West Sussex, RH19 1BP (United Kingdom)

2006-07-01T23:59:59.000Z

302

Development of Commodity Grade, Lower Cost Carbon Fiber - Commercial Applications  

SciTech Connect

In pursuit of the goal to produce ultra-lightweight fuel efficient vehicles, there has been great excitement during the last few years about the potential for using carbon fiber reinforced composites in high volume applications. Currently, the greatest hurdle that inhibits wider implementation of carbon fiber composites in transportation is the high cost of the fiber when compared to other candidate materials. As part of the United States Department of Energy s FreedomCAR initiative, significant research is being conducted to develop lower cost, high volume technologies for producing carbon fiber. This paper will highlight the on-going research in this area. Through Department of Energy (DOE) sponsorship, Oak Ridge National Laboratory (ORNL) and its partners have been working with the US Automotive Composites Consortium (ACC) to develop technologies that would enable the production of carbon fiber at 5-7 dollars per pound. Achievement of this cost goal would allow the introduction of carbon fiber based composites into a greater number of applications for future vehicles. The approach has necessitated the development of both alternative precursors and more efficient production methods. Alternative precursors under investigation include textile grade polyacrylonitrile (PAN) fibers and fibers from lignin-based feedstocks. Previously, as part of the research program, Hexcel Corporation developed the science necessary to allow textile grade PAN to be used as a precursor rather than typical carbon fiber grade precursors. Efforts are also underway to develop carbon fiber precursors from lignin-based feedstocks. ORNL and its partners are working on this effort with domestic pulp and paper producers. In terms of alternative production methods, ORNL has developed a microwave-based carbonization unit that can process pre-oxidized fiber at over 200 inches per minute. ORNL has also developed a new method of high speed oxidation and a new method for precursor stabilization. Additionally, novel methods of activating carbon fiber surfaces have been developed which allow atomic oxygen concentrations as high as 25-30% to be achieved rather than the more typical 4-8% achieved by the standard industrial ozone treatment.

Warren, Charles David [ORNL; Paulauskas, Felix L [ORNL; Baker, Frederick S [ORNL; Eberle, Cliff [ORNL; Naskar, Amit K [ORNL

2009-01-01T23:59:59.000Z

303

Transfer function identification in power system applications  

Science Conference Proceedings (OSTI)

This paper presents an introduction to concepts and applications of transfer function identification in power systems. The paper begins with a brief introduction to transfer function identification methods using least-squares approaches and then discusses applications which include SVC's, model validation applications, and software validation. A comparison is also made between eigenvalues obtained from transfer function identification and small signal analysis. Methods for testing the validity of identified transfer functions are also discussed.

Smith, J.R.; Fatehi, F.; Woods, C.S. (Montana State Univ., Bozeman, MT (United States)); Hauer, J.F. (Bonneville Power Administration, Portland, OR (United States)); Trudnowski, D.J. (Battelle Pacific Northwest Labs., Richland, WA (United States))

1993-08-01T23:59:59.000Z

304

Order Module--DOE O 440.1B, WORKER PROTECTION PROGRAM FOR DOE (INCLUDING  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Order Module--DOE O 440.1B, WORKER PROTECTION PROGRAM FOR DOE Order Module--DOE O 440.1B, WORKER PROTECTION PROGRAM FOR DOE (INCLUDING NNSA) FEDERAL EMPLOYEES Order Module--DOE O 440.1B, WORKER PROTECTION PROGRAM FOR DOE (INCLUDING NNSA) FEDERAL EMPLOYEES The familiar level of this module is divided into two sections. In the first section, we will discuss the objective, requirements, and the responsibilities assigned to the heads of field elements. In the second section, we will discuss the content of attachment 1, Functional Area Requirements. We have provided examples and a practice to help familiarize you with the material. The practice will also help prepare you for the criterion test. DOE Order Self Study Modules - DOE O 440.1B, Worker Protection Management for DOE (Including the National Nuclear Security Administration) Federal

305

C3E also includes a network of leaders from the public, private, non-profit  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

C3E also includes a network of leaders from the public, private, non-profit, C3E also includes a network of leaders from the public, private, non-profit, and academic sectors who support advocacy, research, scholarships, hands-on training, funding, and networking opportunities to prepare and inspire young women to enter and thrive in STEM fields. C3E Network participants have pledged many types of commitments, from highlighting female role models to creating hands-on activities for young girls. Ongoing activities include: * Filming and featuring women in clean energy fields on online / TV outlets (Earth Day Network); * Designing pilot projects and expanding Young Women's Conferences at DOE's

306

Including Alternative Resources in State Renewable Portfolio Standards: Current Design and Implementation Experience  

NLE Websites -- All DOE Office Websites (Extended Search)

Including Alternative Resources Including Alternative Resources in State Renewable Portfolio Standards: Current Design and Implementation Experience Jenny Heeter and Lori Bird Technical Report NREL/TP-6A20-55979 November 2012 NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency & Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. National Renewable Energy Laboratory 15013 Denver West Parkway Golden, Colorado 80401 303-275-3000 * www.nrel.gov Contract No. DE-AC36-08GO28308 Including Alternative Resources in State Renewable Portfolio Standards: Current Design and Implementation Experience Jenny Heeter and Lori Bird Prepared under Task No. SAO9.3110

307

The American Recovery and Reinvestment Act Includes $4.5 billion for the  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

The American Recovery and Reinvestment Act Includes $4.5 billion The American Recovery and Reinvestment Act Includes $4.5 billion for the Office of Electricity Delivery and Energy Reliability The American Recovery and Reinvestment Act Includes $4.5 billion for the Office of Electricity Delivery and Energy Reliability February 25, 2009 - 4:52pm Addthis President Barack Obama signed into law the American Recovery and Reinvestment Act of 2009 (P.L.111-5). The $787 billion economic recovery package represents the largest and most ambitious effort to stimulate the economy in United States history. The Department of Energy (DOE) will be responsible for implementing over $38 billion of the $787 billion package. Of the DOE total, $4.5 Billion is allotted to the Office of Electricity Delivery and Energy Reliability. As outlined in the legislation, these funds are an investment in a

308

Order Module--DOE O 440.1B, WORKER PROTECTION PROGRAM FOR DOE (INCLUDING  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

40.1B, WORKER PROTECTION PROGRAM FOR DOE 40.1B, WORKER PROTECTION PROGRAM FOR DOE (INCLUDING NNSA) FEDERAL EMPLOYEES Order Module--DOE O 440.1B, WORKER PROTECTION PROGRAM FOR DOE (INCLUDING NNSA) FEDERAL EMPLOYEES The familiar level of this module is divided into two sections. In the first section, we will discuss the objective, requirements, and the responsibilities assigned to the heads of field elements. In the second section, we will discuss the content of attachment 1, Functional Area Requirements. We have provided examples and a practice to help familiarize you with the material. The practice will also help prepare you for the criterion test. DOE Order Self Study Modules - DOE O 440.1B, Worker Protection Management for DOE (Including the National Nuclear Security Administration) Federal Employees

309

Sol-Gel Fundamentals and Applications  

Science Conference Proceedings (OSTI)

October 20, 2010 ... This lecture presents an overview of most recent biological applications .... Remarkable findings of these studies included the discovery of an evaporation-rate singularity at the steady-state drying line during deposition, the

310

Alloy Groupings by Application or Major Characteristic  

Science Conference Proceedings (OSTI)

...Missile bodies Missile fins Aircraft pylons Aircraft canopies Wing flaps Speed brakes Hatch covers Hydraulic pumps Automotive suspension systems and cross-members Fuel pumps Brake valves Armored cupolas Aerospace structural parts Applications include:...

311

Real-World Applications of Multiobjective Optimization  

Science Conference Proceedings (OSTI)

This chapter presents a number of illustrative case studies of a wide range of applications of multiobjective optimization methods, in areas ranging from engineering design to medical treatments. The methods used include both conventional mathematical ...

Theodor Stewart; Oliver Bandte; Heinrich Braun; Nirupam Chakraborti; Matthias Ehrgott; Mathias Gbelt; Yaochu Jin; Hirotaka Nakayama; Silvia Poles; Danilo Stefano

2008-10-01T23:59:59.000Z

312

An Assimilated Dataset for Earth Science Applications  

Science Conference Proceedings (OSTI)

The Data Assimilation Office at NASA's Goddard Space Flight Center is currently producing a multiyear gridded global atmospheric dataset for use in climate research, including tropospheric chemistry applications. The data, which are being made ...

Siegfried D. Schubert; Richard B. Rood; James Pfaendtner

1993-12-01T23:59:59.000Z

313

Insolation resource assessment program plan. Fiscal year 1979--Fiscal year 1981. [Includes glossary  

SciTech Connect

The purpose of the Insolation Resource Assessment Program is to collect, standardize, certify, process,, and archive geophysical data for solar energy applications. The principal solar parameters to be measured are global, direct, diffuse and total radiation on an inclined surface. The measurement of the spectral distribution of solar radiation is also important to the development of several technologies. The aim of many of the completed, current, and planned projects presented in the IRAP Plan is to improve solar data collection methods and procedures and to refine solar radiation forecasting capabilities.

1979-01-01T23:59:59.000Z

314

Fourier and Cauchy-Stieltjes transforms of power laws including stable distributions  

E-Print Network (OSTI)

We introduce a class of probability measures whose densities near infinity are mixtures of Pareto distributions. This class can be characterized by the Fourier transform which has a power series expansion including real powers, not only integer powers. This class includes stable distributions in probability and also non-commutative probability theories. We also characterize the class in terms of the Cauchy-Stieltjes transform and the Voiculescu transform. If the stability index is greater than one, stable distributions in probability theory do not belong to that class, while they do in non-commutative probability.

Takahiro Hasebe

2011-07-20T23:59:59.000Z

315

Prototype solar heating and cooling systems, including potable hot water. Quarterly report  

DOE Green Energy (OSTI)

The progress made in the development, delivery and support of two prototype solar heating and cooling systems including potable hot water is reported. The system consists of the following subsystems: collector, auxiliary heating, potable hot water, storage, control, transport, and government-furnished site data acquisition. Included is a comparison of the proposed Solaron-Heat Pump and Solaron-Desiccant Heating and Cooling Systems, Installation Drawings, data on the Akron House at Akron, Ohio, and other program activities from July 1, 1977 through November 9, 1977.

Not Available

1977-12-01T23:59:59.000Z

316

Combinatorial evaluation of systems including decomposition of a system representation into fundamental cycles  

DOE Patents (OSTI)

One embodiment of the present invention includes a computer operable to represent a physical system with a graphical data structure corresponding to a matroid. The graphical data structure corresponds to a number of vertices and a number of edges that each correspond to two of the vertices. The computer is further operable to define a closed pathway arrangement with the graphical data structure and identify each different one of a number of fundamental cycles by evaluating a different respective one of the edges with a spanning tree representation. The fundamental cycles each include three or more of the vertices.

Oliveira, Joseph S. (Richland, WA); Jones-Oliveira, Janet B. (Richland, WA); Bailey, Colin G. (Wellington, NZ); Gull, Dean W. (Seattle, WA)

2008-07-01T23:59:59.000Z

317

FOMGT 456 -Management Science Applications Spring 2000  

E-Print Network (OSTI)

that are covered include: integer and nonlinear programming, basic network models and programming, inventory theory to be Covered 1. Review of linear programming Supplementary papers and videos, which illustrate applications of integer programming Supplemental paper and video, which illustrates an application to operations

Nagurney, Anna

318

Robust, accurate, and non-contacting vibration measurement systems: Summary of comparison measurements of the robust laser interferometer and typical accelerometer systems. Volume 1  

Science Conference Proceedings (OSTI)

Epoch Engineering, Incorporated (EEI) has completed a series of vibration measurements comparing their newly-developed Robust Laser Interferometer (RLI) with accelerometer-based instrumentation systems. EEI has successfully demonstrated, on several pieces of commonplace machinery, that non-contact, line-of-sight measurements are practical and yield results equal to or, in some cases, better than customary field implementations of accelerometers. The demonstration included analysis and comparison of such phenomena as nonlinearity, transverse sensitivity, harmonics, and signal-to-noise ratio. Fast Fourier Transformations were performed on the accelerometer and the laser system outputs to provide a comparison basis. The RLI was demonstrated, within the limits of the task, to be a viable, line-of-sight, non-contact alternative to accelerometer systems. Several different kinds of machinery were instrumented and compared, including a small pump, a gear-driven cement mixer, a rotor kit, and two small fans. Known machinery vibration sources were verified and RLI system output file formats were verified to be compatible with commercial computer programs used for vibration monitoring and trend analysis. The RLI was also observed to be less subject to electromagnetic interference (EMI) and more capable at very low frequencies.

Goodenow, T.C.; Shipman, R.L.; Holland, H.M. [Epoch Engineering, Inc., Gaithersburg, MD (United States)

1995-06-01T23:59:59.000Z

319

Robust, accurate, and non-contacting vibration measurement systems: Supplemental appendices presenting comparison measurements of the robust laser interferometer and typical accelerometer systems. Volume 2  

Science Conference Proceedings (OSTI)

Epoch Engineering, Incorporated (EEI) has completed a series of vibration measurements comparing their newly-developed Robust Laser Interferometer (RLI) with accelerometer-based instrumentation systems. EEI has successfully demonstrated, on several pieces of commonplace machinery, that non-contact, line-of-sight measurements are practical and yield results equal to or, in some cases, better than customary field implementations of accelerometers. The demonstration included analysis and comparison of such phenomena as nonlinearity, transverse sensitivity, harmonics, and signal-to-noise ratio. Fast Fourier Transformations were performed on the accelerometer and the laser system outputs to provide a comparison basis. The RLI was demonstrated, within the limits o the task, to be a viable, line-of-sight, non-contact alternative to accelerometer systems. Several different kinds of machinery were instrumented and. compared, including a small pump, a gear-driven cement mixer, a rotor kit, and two small fans. Known machinery vibration sources were verified and RLI system output file formats were verified to be compatible with commercial computer programs used for vibration monitoring and trend analysis. The RLI was also observed to be less subject to electromagnetic interference (EMI) and more capable at very low frequencies. This document, Volume 2, provides the appendices to this report.

Goodenow, T.C.; Shipman, R.L.; Holland, H.M. [Epoch Engineering, Inc., Gaithersburg, MD (United States)

1995-06-01T23:59:59.000Z

320

Performance of Trasuranic-Loaded Fully Ceramic Micro-Encapsulated Fuel in LWRs Interim Report, Including Void Reactivity Evaluation  

Science Conference Proceedings (OSTI)

The current focus of the Deep Burn Project is on once-through burning of transuranice (TRU) in light water reactors (LWRs). The fuel form is called Fully-Ceramic Micro-encapsulated (FCM) fuel, a concept that borrows the tri-isotropic (TRISO) fuel particle design from high-temperature reactor technology. In the Deep Burn LWR (DB-LWR) concept, these fuel particles would be pressed into compacts using SiC matrix material and loaded into fuel pins for use in conventional LWRs. The TRU loading comes from the spent fuel of a conventional LWR after 5 years of cooling. Unit cell calculations have been performed using the DRAGON-4 code in order assess the physics attributes of TRU-only FCM fuel in an LWR lattice. Depletion calculations assuming an infinite lattice condition were performed with calculations of various reactivity coefficients performed at each step. Unit cells containing typical UO2 and MOX fuel were analyzed in the same way to provide a baseline against which to compare the TRU-only FCM fuel. Loading of TRU-only FCM fuel into a pin without significant quantities of uranium challenges the design from the standpoint of several key reactivity parameters, particularly void reactivity, and to some degree, the Doppler coefficient. These unit cells, while providing an indication of how a whole core of similar fuel would behave, also provide information of how individual pins of TRU-only FCM fuel would influence the reactivity behavior of a heterogeneous assembly. If these FCM fuel pins are included in a heterogeneous assembly with LEU fuel pins, the overall reactivity behavior would be dominated by the uranium pins while attractive TRU destruction performance of the TRU-only FCM fuel pins may be preserved. A configuration such as this would be similar to CONFU assemblies analyzed in previous studies. Analogous to the plutonium content limits imposed on MOX fuel, some amount of TRU-only FCM pins in an otherwise-uranium fuel assembly may give acceptable reactivity performance. Assembly calculations will be performed in future work to explore the design options for heterogeneous assemblies of this type and their impact on reactivity coefficients.

Michael A. Pope; Brian Boer; Gilles Youinou; Abderrafi M. Ougouag

2011-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Process for removing and detoxifying cadmium from scrap metal including mixed waste  

SciTech Connect

Cadmium-bearing scrap from nuclear applications, such as neutron shielding and reactor control and safety rods, must usually be handled as mixed waste since it is radioactive and the cadmium in it is both leachable and highly toxic. Removing the cadmium from this scrap, and converting it to a nonleachable and minimally radioactive form, would greatly simplify disposal or recycling. A process now under development will do this by shredding the scrap; leaching it with reagents which selectively dissolve out the cadmium; reprecipitating the cadmium as its highly insoluble sulfide; then fusing the sulfide into a glassy matrix to bring its leachability below EPA limits before disposal. Alternatively, the cadmium may be recovered for reuse. A particular advantage of the process is that all reagents (except the glass frit) can easily be recovered and reused in a nearly closed cycle, minimizing the risk of radioactive release. The process does not harm common metals such as aluminum, iron and stainless steel, and is also applicable to non-nuclear cadmium-bearing scrap such as nickel-cadmium batteries.

Kronberg, J.W.

1994-07-01T23:59:59.000Z

322

Prototype solar heating and cooling systems including potable hot water. Quarterly reports  

DOE Green Energy (OSTI)

The activities conducted by Solaron Corporation from November 1977 through September 1978 are summarized and the progress made in the development, delivery and support of two prototype solar heating and cooling systems including potable hot water is covered. The system consists of the following subsystems: solar collector, auxiliary heating, potable hot water, storage, control, transport, and government-furnished site data acquisition.

Williamson, R.

1978-10-01T23:59:59.000Z

323

Solar Energy Education. Industrial arts: teacher's guide. Field test edition. [Includes glossary  

SciTech Connect

An instructional aid is presented which integrates the subject of solar energy into the classroom study of industrial arts. This guide for teachers was produced in addition to the student activities book for industrial arts by the USDOE Solar Energy Education. A glossary of solar energy terms is included. (BCS)

1981-05-01T23:59:59.000Z

324

ECOVILLAGE FACTS The complex includes 50 apartments (18 original and 32 new)  

E-Print Network (OSTI)

, community gatherings o Kitchen o Playroom o Dryers for Ecovillage residents o Solar water heater o Solar of the Ecovillage apartments include: o solar tubes and compact fluorescent lighting o low-flow toilets College-harvested wood o natural building techniques o a composting toilet o a net-metering solar electric

Baltisberger, Jay H.

325

Solar Energy Education. Home economics: teacher's guide. Field test edition. [Includes glossary  

SciTech Connect

An instructional aid is provided for home economics teachers who wish to integrate the subject of solar energy into their classroom activities. This teacher's guide was produced along with the student activities book for home economics by the US Department of Energy Solar Energy Education. A glossary of solar energy terms is included. (BCS)

1981-06-01T23:59:59.000Z

326

Method of preparing a negative electrode including lithium alloy for use within a secondary electrochemical cell  

DOE Patents (OSTI)

A negative electrode that includes a lithium alloy as active material is prepared by briefly submerging a porous, electrically conductive substrate within a melt of the alloy. Prior to solidification, excess melt can be removed by vibrating or otherwise manipulating the filled substrate to expose interstitial surfaces. Electrodes of such as solid lithium-aluminum filled within a substrate of metal foam are provided.

Tomczuk, Zygmunt (Palos Hills, IL); Olszanski, Theodore W. (Roselle, IL); Battles, James E. (Oak Forest, IL)

1977-03-08T23:59:59.000Z

327

Postgraduate Handbook Courses, programs and any arrangements for programs including staff  

E-Print Network (OSTI)

corn oil; Camelina oil. One of the following: Trans-Esterification, Esterification, Hydrotreating-process renewable biomass and petroleum. 5 POTENTIALLY RELEVANT I Naphtha, LPG Camelina oil Hydrotreating 5 including peat, dung, plant-oils, bees wax, rendered animal fats, draft animals, natural derived sources

Benatallah, Boualem

328

Solar Energy Education. Industrial arts: teacher's guide. Field test edition. [Includes glossary  

DOE Green Energy (OSTI)

An instructional aid is presented which integrates the subject of solar energy into the classroom study of industrial arts. This guide for teachers was produced in addition to the student activities book for industrial arts by the USDOE Solar Energy Education. A glossary of solar energy terms is included. (BCS)

Not Available

1981-05-01T23:59:59.000Z

329

QUALITATIVE PROPERTIES OF A 3-STEPS MODEL OF ANAEROBIC DIGESTION INCLUDING HYDROLYSIS OF PARTICULATE MATTER  

E-Print Network (OSTI)

QUALITATIVE PROPERTIES OF A 3-STEPS MODEL OF ANAEROBIC DIGESTION INCLUDING HYDROLYSIS-SupAgro MISTEA, 2 p. Viala 34060 Montpellier, France, fekih@supagro.inra.fr Introduction. Anaerobic digestion, the anaerobic digestion is generally considered as a three step process: hydrolysis and liquefaction

Paris-Sud XI, Université de

330

ON THE STANDARD METABOLIC RATES OF TROPICAL TUNAS, INCLUDING THE EFFECf OF BODY SIZE AND  

E-Print Network (OSTI)

ON THE STANDARD METABOLIC RATES OF TROPICAL TUNAS, INCLUDING THE EFFECf OF BODY SIZE AND ACUTE. This study was undertaken to obtain these data for the tropical tuna species, yellowfin tuna, Tkunnl tuna, KatsltWOO1t8 pelamis, previously published. The effect of acute temperature change on the SMR

331

Faddeev-type calculations of few-body nuclear reactions including Coulomb interaction  

E-Print Network (OSTI)

The method of screening and renormalization is used to include the Coulomb interaction between the charged particles in the description of few-body nuclear reactions. Calculations are done in the framework of Faddeev-type equations in momentum-space. The reliability of the method is demonstrated. The Coulomb effect on observables is discussed.

A. Deltuva

2008-10-24T23:59:59.000Z

332

Process, including PSA and membrane separation, for separating hydrogen from hydrocarbons  

DOE Patents (OSTI)

An improved process for separating hydrogen from hydrocarbons. The process includes a pressure swing adsorption step, a compression/cooling step and a membrane separation step. The membrane step relies on achieving a methane/hydrogen selectivity of at least about 2.5 under the conditions of the process.

Baker, Richard W. (Palo Alto, CA); Lokhandwala, Kaaeid A. (Union City, CA); He, Zhenjie (Fremont, CA); Pinnau, Ingo (Palo Alto, CA)

2001-01-01T23:59:59.000Z

333

CHEMICAL WASTE RECYCLING PROGRAM EMPTY CHEMICAL BOTTLES: which include all glass, plastic and metal bottles that  

E-Print Network (OSTI)

CHEMICAL WASTE RECYCLING PROGRAM EMPTY CHEMICAL BOTTLES: which include all glass, plastic and metal bottles that previously contained chemicals (hazardous or non-hazardous) are collected by CWS for recycling. Bottles should be dry and empty without chemical residue. Rinse and collect rinsate in chemical

Ungerleider, Leslie G.

334

Selecting Optional Fees Optional fees include meal plans, money on Tigerstripe, and a TAPS yearbook. All  

E-Print Network (OSTI)

supports all of the services at Redfern and includes: · Professional services of primary health care on pharmaceuticals, psychological testing, laboratory and x- ray services. · After Hours Nursewise telephone service. http://sisweb.clemson.edu/ Health Fee Policy University policy requires all students registered for six

Bolding, M. Chad

335

Solar water heater installation guidelines. A manual for homeowners and professionals. [Includes glossary  

SciTech Connect

The guidelines include detailed diagrams, a selected glossary, a bibliography of books and manuals which might prove useful and a checklist which should be used during and after the installation. The guidelines explain generally how to install a liquid solar hot water heater, but not a specific system. The following are covered: collector location, collector installation, plumbing, solar storage tanks, electrical, and insulation. (MHR)

1978-04-01T23:59:59.000Z

336

Solar Energy Education. Home economics: teacher's guide. Field test edition. [Includes glossary  

DOE Green Energy (OSTI)

An instructional aid is provided for home economics teachers who wish to integrate the subject of solar energy into their classroom activities. This teacher's guide was produced along with the student activities book for home economics by the US Department of Energy Solar Energy Education. A glossary of solar energy terms is included. (BCS)

Not Available

1981-06-01T23:59:59.000Z

337

Prototype solar heating and cooling systems including potable hot water. Quarterly reports, November 1976--June 1977  

DOE Green Energy (OSTI)

This report covers the progress made in the development, delivery and support of two prototype solar heating and cooling systems including potable hot water. The system consists of the following subsystems: collector, auxiliary heating, potable hot water, storage, control, transport, and government-furnished site data acquisition.

Not Available

1978-12-01T23:59:59.000Z

338

THERMOMECHANICS OF PV MODULES INCLUDING THE VISCOELASTICITY OF EVA Ulrich Eitner1,  

E-Print Network (OSTI)

in the cell distance is 170µm. Keywords: PV module, Encapsulation, Simulation, Reliability, Mechanics 1THERMOMECHANICS OF PV MODULES INCLUDING THE VISCOELASTICITY OF EVA Ulrich Eitner1, *, Matthias by a comparison to displacement experiments where the thermomechanical deformation of solar cells in a PV laminate

339

Seismic fracture analysis of concrete gravity dams including dam-reservoir interaction  

Science Conference Proceedings (OSTI)

In this study, the seismic fracture response of concrete gravity dams is investigated with considering the effects of dam-reservoir interaction. A co-axial rotating crack model (CRCM), which includes the strain softening behavior, is selected for concrete ... Keywords: Concrete gravity dam, Dam-reservoir interaction, Non-linear analysis, Seismic fracture

Yusuf Calayir; Muhammet Karaton

2005-07-01T23:59:59.000Z

340

Security and Access Policy Security of and access to campus facilities, including campus residences  

E-Print Network (OSTI)

Security and Access Policy Security of and access to campus facilities, including campus residences facilities. Residence halls are secured 24 hours a day. Over extended breaks, the doors of all residence halls will be secured around the clock. Some facilities may have individual hours, which may vary

Escher, Christine

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

The Fuels and Lubricants Research Division of Southwest Research includes extensive engines, fuels and lubricants research,  

E-Print Network (OSTI)

Caterpillar 1K Lubricant Test This test evaluates the piston deposits, liner wear, and oil consumption and oil consumption. The test is proposed for inclusion in the PC-10 category. Mack T8/T8A/T8E Lubricant of Mack engine oil specification EON+ 03, CI-4+ and will be included in PC-10. Mack T12 Lubricant Test

Chapman, Clark R.

342

ELECTRIC PROPULSION APPLICATIONS FOR SNAP SYSTEMS  

SciTech Connect

The application of SNAP systems to electric propulsion was investigated. A review is given of the basic analysis involved in establishing optimum power levels and payload capabilities for electric spacecraft, and several typical missions are analyzed to determine the usefulness of the SNAP systems which are under development or systems which are based on the current SNAP technology. In general, it is found that SNAP power units in the range of 60 to 180 kw offer significant mission capability when used in conjunction with initial spacecraft weights of about 10,000 lb in a low-level orbit. (auth)

Morse, C.J.

1962-04-01T23:59:59.000Z

343

A model for the directional distribution of the diffuse sky radiance with an application to a CPC collector  

SciTech Connect

The development of a new, semi-empirical model for the directional distribution of the diffuse radiance is reported. The proposed regression-type model, with the form of its base functions obtained from physical principles, is based on a combination of the purely physical reasoning approach and the purely empirical approach. Direct multiple-scattering calculations are circumvented through the use of the method of successive orders of scattering. The model is calibrated for the mean diffuse radiance estimated under all sky conditions reported in a large and comprehensive diffuse radiance data set. It is found that only a small increase in accuracy is gained by including higher orders of scattering, and this increase does not justify the complexity of the resulting model. Therefore, the single scattering approximation is recommended. The use of the model is illustrated in a typical application, in which the fraction of diffuse radiation intercepted by the receive of a compound parabolic concentrator is computed.

Siala, F.M.F. (Center for Solar Energy Studies, Tripoli (Libya)); Hooper, F.C. (Univ. of Toronto, Ontario (Canada))

1990-01-01T23:59:59.000Z

344

Design Concept and Application of Small Nuclear Power Reactor  

Science Conference Proceedings (OSTI)

The outline of the recent design concepts and those features of the small nuclear power rector are described, including specifications, present design status, application and so on.

Minato, Akio [CRIEPI, Central Research Institute of Electric Power Industry, Tokyo (Japan); Sekimoto, Hiroshi [Center for Research into Innovative Nuclear Energy Systems (CRINES) Tokyo Institute of Technology 2-12-1, Ookayama, Meguro-ku, Tokyo, 152-8550 (Japan)

2009-03-31T23:59:59.000Z

345

6.013 Electromagnetics and Applications, Fall 2002  

E-Print Network (OSTI)

Electromagnetic phenomena are explored in modern applications including wireless communications, circuits, computer interconnects and peripherals, optical fiber links and components, microwave communications and radar, ...

Staelin, David H.

346

Bayesian Statistics and Its Application to Quantitative Trait Loci Mapping.  

E-Print Network (OSTI)

??Quantitative trait loci (QTL) mapping is one of the applications of statistics in genetics.This dissertation focuses two problems on QTL mapping which include a newpermutation (more)

Che, Xiaohong

2011-01-01T23:59:59.000Z

347

Anniversary Scholarship Application Form  

E-Print Network (OSTI)

at the University of Cambridge should complete the application form below and send it to The Pakistan Application Pakistan. Pakistan nationals who attend schools outside Pakistan are not eligible. 2. Applicants must complete the scholarship application form should be submitted to: The Pakistan Application Centre Cambridge

Travis, Adrian

348

Evaluation of Trenchless Installation Technology for Radioactive Wastewater Piping Applications  

SciTech Connect

The U.S. Department of Energy (DOE) Office of Environmental Management (EM) cleanup mission at Oak Ridge National Laboratory (ORNL) includes dispositioning facilities, contaminated legacy materials/waste, and contamination sources and remediation of soil under facilities, groundwater, and surface water to support final Records of Decision (RODs). The Integrated Facilities Disposition Project (IFDP) is a roughly $15B project for completion of the EM mission at Oak Ridge, with a project duration of up to 35 years. The IFDP Mission Need Statement - Critical Decision-0 (CD-0) - was approved by DOE in July 2007, and the IFDP Alternative Selection and Cost Range - Critical Decision-1 (CD-1) - was approved in November 2008. The IFDP scope includes reconfiguration of waste collection and treatment systems as needed to complete the IFDP remediation and decontamination and decommissioning (D&D) missions in a safe and cost-effective manner while maintaining compliance with all governing regulations and bodies and preserving the support of continuing operations at ORNL. A step in the CD-1 approval process included an external technical review (ETR) of technical approaches proposed in the CD-1 document related to the facility reconfiguration for the ORNL radioactive waste and liquid low-level waste management systems. The ETR team recommended that the IFDP team consider the use of trenchless technologies for installing pipelines underground in and around contaminated sites as part of the alternatives evaluations required in support of the CD-2 process. The team specifically recommended evaluating trenchless technologies for installing new pipes in existing underground pipelines as an alternative to conventional open trench installation methods. Potential benefits could include reduction in project costs, less costly underground piping, fewer disruptions of ongoing and surface activities, and lower risk for workers. While trenchless technologies have been used extensively in the sanitary sewer and natural gas pipeline industries, they have been used far less in contaminated environments. Although trenchless technologies have been used at ORNL in limited applications to install new potable water and gas lines, the technologies have not been used in radioactive applications. This study evaluates the technical risks, benefits, and economics for installing gravity drained and pressurized piping using trenchless technologies compared to conventional installation methods for radioactive applications under ORNL geological conditions. A range of trenchless installation technologies was reviewed for this report for general applicability for replacing existing contaminated piping and/or installing new pipelines in potentially contaminated areas. Installation methods that were determined to have potential for use in typical ORNL contaminated environments were then evaluated in more detail for three specific ORNL applications. Each feasible alternative was evaluated against the baseline conventional open trench installation method using weighted criteria in the areas of environment, safety, and health (ES&H); project cost and schedule; and technical operability. The formulation of alternatives for evaluation, the development of selection criteria, and the scoring of alternatives were performed by ORNL staff with input from vendors and consultants. A description of the evaluation methodology and the evaluation results are documented in the following sections of this report.

Robinson, Sharon M [ORNL; Jubin, Robert Thomas [ORNL; Patton, Bradley D [ORNL; Sullivan, Nicholas M [ORNL; Bugbee, Kathy P [ORNL

2009-09-01T23:59:59.000Z

349

Calculation of two-phase dispersed droplet-in-vapor flows including normal shock waves  

DOE Green Energy (OSTI)

A method for calculating quasi-one-dimensional, steady-state, two-phase dispersed droplet-in-vapor flow has been developed. The technique is applicable to both subsonic and supersonic single component flow in which normal shock waves may occur, and is the basis for a two-dimensional model. The flow is assumed to be inviscid except for droplet drag. Temperature and pressure equilibrium between phases is assumed, although this is not a requirement of the technique. Example calculations of flow in one-dimensional nozzles with and without normal shocks are given and compared with experimentally measured pressure profiles for both low quality and high quality two-phase steam/water flow.

Comfort, W.J.; Alger, T.W.; Giedt, W.H.; Crowe, C.T.

1976-07-28T23:59:59.000Z

350

Design, Fabrication and Characterization of a Piezoelectric Microgenerator Including a Power Management Circuit  

E-Print Network (OSTI)

We report in this paper the design, fabrication and experimental characterization of a piezoelectric MEMS microgenerator. This device scavenges the energy of ambient mechanical vibrations characterized by frequencies in the range of 1 kHz. This component is made with Aluminum Nitride thin film deposited with a CMOS compatible process. Moreover we analyze two possible solutions for the signal rectification: a discrete doubler-rectifier and a full custom power management circuit. The ASIC developed for this application takes advantage of diodes with very low threshold voltage and therefore allows the conversion of extremely low input voltages corresponding to very weak input accelerations. The volume of the proposed generator is inferior to 1mm3 and the generated powers are in the range of 1$\\mu$W. This system is intended to supply power to autonomous wireless sensor nodes.

Marzencki, M; Basrour, S

2008-01-01T23:59:59.000Z

351

DESIGN, FABRICATION AND CHARACTERIZATION OF A PIEZOELECTRIC MICROGENERATOR INCLUDING A POWER MANAGEMENT CIRCUIT  

E-Print Network (OSTI)

We report in this paper the design, fabrication and experimental characterization of a piezoelectric MEMS microgenerator. This device scavenges the energy of ambient mechanical vibrations characterized by frequencies in the range of 1 kHz. This component is made with Aluminum Nitride thin film deposited with a CMOS compatible process. Moreover we analyze two possible solutions for the signal rectification: a discrete doubler-rectifier and a full custom power management circuit. The ASIC developed for this application takes advantage of diodes with very low threshold voltage and therefore allows the conversion of extremely low input voltages corresponding to very weak input accelerations. The volume of the proposed generator is inferior to 1mm 3 and the generated powers are in the range of 1W. This system is intended to supply power to autonomous wireless sensor nodes. 1.

M. Marzencki; Y. Ammar; S. Basrour

2008-01-01T23:59:59.000Z

352

Method for pulse control in a laser including a stimulated brillouin scattering mirror system  

DOE Patents (OSTI)

A laser system, such as a master oscillator/power amplifier system, comprises a gain medium and a stimulated Brillouin scattering SBS mirror system. The SBS mirror system includes an in situ filtered SBS medium that comprises a compound having a small negative non-linear index of refraction, such as a perfluoro compound. An SBS relay telescope having a telescope focal point includes a baffle at the telescope focal point which blocks off angle beams. A beam splitter is placed between the SBS mirror system and the SBS relay telescope, directing a fraction of the beam to an alternate beam path for an alignment fiducial. The SBS mirror system has a collimated SBS cell and a focused SBS cell. An adjustable attenuator is placed between the collimated SBS cell and the focused SBS cell, by which pulse width of the reflected beam can be adjusted.

Dane, C. Brent (Livermore, CA); Hackel, Lloyd (Livermore, CA); Harris, Fritz B. (Rocklin, CA)

2007-10-23T23:59:59.000Z

353

Policy Flash 2013-49 Updating Reporting Requirement Checklist including the  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Policy Flash 2013-49 Updating Reporting Requirement Checklist Policy Flash 2013-49 Updating Reporting Requirement Checklist including the research performance progress report Policy Flash 2013-49 Updating Reporting Requirement Checklist including the research performance progress report Questions concerning this policy flash should be directed to Ellen Colligan, of the Contract and Financial Assistance Policy Division, Office of Contract Management, Office of Acquisition and Project Management at (202) 287-1776, Ellen.colligan@hq.doe.gov Policy Flash 2013-49.pdf Attch_FA_RepReqChecklist_COMBINED_FINAL_4-23-13 (3).pdf More Documents & Publications ATTACHMENT FLASH 2011-46(6) Federal Assistance Reporting Checklist and Instructions for Projects Federal Assistance Reporting Checklist and Instructions for RD&D Projects

354

" Row: End Uses;" " Column: Energy Sources, including Net Electricity;"  

U.S. Energy Information Administration (EIA) Indexed Site

5 End Uses of Fuel Consumption, 2010;" 5 End Uses of Fuel Consumption, 2010;" " Level: National and Regional Data; " " Row: End Uses;" " Column: Energy Sources, including Net Electricity;" " Unit: Physical Units or Btu." " "," ",," ","Distillate"," "," ","Coal"," " " ",,,,"Fuel Oil",,,"(excluding Coal" " "," ","Net","Residual","and","Natural Gas(c)","LPG and","Coke and Breeze)"," " " ","Total","Electricity(a)","Fuel Oil","Diesel Fuel(b)","(billion","NGL(d)","(million","Other(e)"

355

" Row: End Uses;" " Column: Energy Sources, including Net Electricity;"  

U.S. Energy Information Administration (EIA) Indexed Site

5 End Uses of Fuel Consumption, 2002;" 5 End Uses of Fuel Consumption, 2002;" " Level: National and Regional Data; " " Row: End Uses;" " Column: Energy Sources, including Net Electricity;" " Unit: Physical Units or Btu." " "," ",," ","Distillate"," "," ",," "," " " ",,,,"Fuel Oil",,,"Coal" " "," ","Net","Residual","and","Natural ","LPG and","(excluding Coal"," ","RSE" " ","Total","Electricity(a)","Fuel Oil","Diesel Fuel(b)","Gas(c)","NGL(d)","Coke and Breeze)","Other(e)","Row"

356

" Row: End Uses;" " Column: Energy Sources, including Net Electricity;"  

U.S. Energy Information Administration (EIA) Indexed Site

6 End Uses of Fuel Consumption, 2010;" 6 End Uses of Fuel Consumption, 2010;" " Level: National and Regional Data; " " Row: End Uses;" " Column: Energy Sources, including Net Electricity;" " Unit: Trillion Btu." " "," ",," ","Distillate"," "," ",," " " ",,,,"Fuel Oil",,,"Coal" " "," ","Net","Residual","and",,"LPG and","(excluding Coal"," " "End Use","Total","Electricity(a)","Fuel Oil","Diesel Fuel(b)","Natural Gas(c)","NGL(d)","Coke and Breeze)","Other(e)"

357

" Row: End Uses;" " Column: Energy Sources, including Net Electricity;"  

U.S. Energy Information Administration (EIA) Indexed Site

6 End Uses of Fuel Consumption, 2002;" 6 End Uses of Fuel Consumption, 2002;" " Level: National and Regional Data; " " Row: End Uses;" " Column: Energy Sources, including Net Electricity;" " Unit: Trillion Btu." " "," ",," ","Distillate"," "," ",," "," " " ",,,,"Fuel Oil",,,"Coal",,"RSE" " "," ","Net","Residual","and","Natural ","LPG and","(excluding Coal"," ","Row" "End Use","Total","Electricity(a)","Fuel Oil","Diesel Fuel(b)","Gas(c)","NGL(d)","Coke and Breeze)","Other(e)","Factors"

358

" Row: End Uses;" " Column: Energy Sources, including Net Electricity;"  

U.S. Energy Information Administration (EIA) Indexed Site

6 End Uses of Fuel Consumption, 2006;" 6 End Uses of Fuel Consumption, 2006;" " Level: National and Regional Data; " " Row: End Uses;" " Column: Energy Sources, including Net Electricity;" " Unit: Trillion Btu." " "," ",," ","Distillate"," "," ",," " " ",,,,"Fuel Oil",,,"Coal" " "," ","Net","Residual","and",,"LPG and","(excluding Coal"," " "End Use","Total","Electricity(a)","Fuel Oil","Diesel Fuel(b)","Natural Gas(c)","NGL(d)","Coke and Breeze)","Other(e)"

359

" Row: End Uses;" " Column: Energy Sources, including Net Electricity;"  

U.S. Energy Information Administration (EIA) Indexed Site

1. End Uses of Fuel Consumption, 1998;" 1. End Uses of Fuel Consumption, 1998;" " Level: National and Regional Data; " " Row: End Uses;" " Column: Energy Sources, including Net Electricity;" " Unit: Physical Units or Btu." " "," ",," ","Distillate"," "," ","Coal"," "," " " ",,,,"Fuel Oil",,,"(excluding Coal" " "," ","Net","Residual","and","Natural Gas(c)","LPG and","Coke and Breeze)"," ","RSE" " ","Total","Electricity(a)","Fuel Oil","Diesel Fuel(b)","(billion","NGL(d)","(million","Other(e)","Row"

360

" Row: End Uses;" " Column: Energy Sources, including Net Electricity;"  

U.S. Energy Information Administration (EIA) Indexed Site

2. End Uses of Fuel Consumption, 1998;" 2. End Uses of Fuel Consumption, 1998;" " Level: National and Regional Data; " " Row: End Uses;" " Column: Energy Sources, including Net Electricity;" " Unit: Trillion Btu." " "," ",," ","Distillate"," "," ",," "," " " ",,,,"Fuel Oil",,,"Coal",,"RSE" " "," ","Net","Residual","and",,"LPG and","(excluding Coal"," ","Row" "End Use","Total","Electricity(a)","Fuel Oil","Diesel Fuel(b)","Natural Gas(c)","NGL(d)","Coke and Breeze)","Other(e)","Factors"

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

2008 CIM-XML Interoperability Including CIM-Based Tools Test  

Science Conference Proceedings (OSTI)

EPRI Initiatives have produced a number of drafts that have now become International Electrotechnical Commission (IEC) standards, including the Common Information Model (CIM) and the Generic Interface Definition (GID) specifications. These standards provide the basis for model-driven information exchange both within and between control centers and other systems in utility operations across the enterprise. Previous interoperability tests validated the use and acceptance of the CIM standard translated into...

2008-12-04T23:59:59.000Z

362

Method of preparing a negative electrode including lithium alloy for use within a secondary electrochemical cell  

DOE Patents (OSTI)

A negative electrode that includes a lithium alloy as active material is prepared by briefly submerging a porous, electrically conductive substrate within a melt of the alloy. Prior to solidification, excess melt can be removed by vibrating or otherwise manipulating the filled substrate to expose interstitial surfaces. Electrodes of such a solid lithium--aluminum filled within a substrate of metal foam are provided. 1 figure, 1 table.

Tomczuk, Z.; Olszanski, W.; Battles, J.E.

1975-12-09T23:59:59.000Z

363

Impact of supersonic and subsonic aircraft on ozone: Including heterogeneous chemical reaction mechanisms  

Science Conference Proceedings (OSTI)

Preliminary calculations suggest that heterogeneous reactions are important in calculating the impact on ozone from emissions of trace gases from aircraft fleets. In this study, three heterogeneous chemical processes that occur on background sulfuric acid aerosols are included and their effects on O{sub 3}, NO{sub x}, Cl{sub x}, HCl, N{sub 2}O{sub 5}, ClONO{sub 2} are calculated.

Kinnison, D.E.; Wuebbles, D.J.

1992-07-05T23:59:59.000Z

364

" Row: End Uses;" " Column: Energy Sources, including Net Electricity;"  

U.S. Energy Information Administration (EIA) Indexed Site

5 End Uses of Fuel Consumption, 2006;" 5 End Uses of Fuel Consumption, 2006;" " Level: National and Regional Data; " " Row: End Uses;" " Column: Energy Sources, including Net Electricity;" " Unit: Physical Units or Btu." " "," ",," ","Distillate"," "," ","Coal"," " " ",,,,"Fuel Oil",,,"(excluding Coal" " "," ","Net","Residual","and","Natural Gas(c)","LPG and","Coke and Breeze)"," " " ","Total","Electricity(a)","Fuel Oil","Diesel Fuel(b)","(billion","NGL(d)","(million","Other(e)"

365

Method and system including a double rotary kiln pyrolysis or gasification of waste material  

DOE Patents (OSTI)

A method of destructively distilling an organic material in particulate form wherein the particulates are introduced through an inlet into one end of an inner rotating kiln ganged to and coaxial with an outer rotating kiln. The inner and outer kilns define a cylindrical annular space with the inlet being positioned in registry with the axis of rotation of the ganged kilns. During operation, the temperature of the wall of the inner rotary kiln at the inlet is not less than about 500.degree. C. to heat the particulate material to a temperature in the range of from about 200.degree. C. to about 900.degree. C. in a pyrolyzing atmosphere to reduce the particulate material as it moves from the one end toward the other end. The reduced particulates including char are transferred to the annular space between the inner and the outer rotating kilns near the other end of the inner rotating kiln and moved longitudinally in the annular space from near the other end toward the one end in the presence of oxygen to combust the char at an elevated temperature to produce a waste material including ash. Also, heat is provided which is transferred to the inner kiln. The waste material including ash leaves the outer rotating kiln near the one end and the pyrolysis vapor leaves through the particulate material inlet.

McIntosh, Michael J. (Bolingbrook, IL); Arzoumanidis, Gregory G. (Naperville, IL)

1997-01-01T23:59:59.000Z

366

Method and system including a double rotary kiln pyrolysis or gasification of waste material  

DOE Patents (OSTI)

A method is described for destructively distilling an organic material in particulate form wherein the particulates are introduced through an inlet into one end of an inner rotating kiln ganged to and coaxial with an outer rotating kiln. The inner and outer kilns define a cylindrical annular space with the inlet being positioned in registry with the axis of rotation of the ganged kilns. During operation, the temperature of the wall of the inner rotary kiln at the inlet is not less than about 500 C to heat the particulate material to a temperature in the range of from about 200 C to about 900 C in a pyrolyzing atmosphere to reduce the particulate material as it moves from the one end toward the other end. The reduced particulates including char are transferred to the annular space between the inner and the outer rotating kilns near the other end of the inner rotating kiln and moved longitudinally in the annular space from near the other end toward the one end in the presence of oxygen to combust the char at an elevated temperature to produce a waste material including ash. Also, heat is provided which is transferred to the inner kiln. The waste material including ash leaves the outer rotating kiln near the one end and the pyrolysis vapor leaves through the particulate material inlet. 5 figs.

McIntosh, M.J.; Arzoumanidis, G.G.

1997-09-02T23:59:59.000Z

367

A method and system including a double rotary kiln pyrolysis or gasification of waste material  

DOE Patents (OSTI)

A method is described for destructively distilling an organic material in particulate form wherein the particulates are introduced through an inlet into one end of an inner rotating kiln ganged to and coaxial with an outer rotating kiln. The inner and outer kilns define a cylindrical annular space with the inlet being positioned in registry with the axis of rotation of the ganged kilns. During operation, the temperature of the wall of the inner rotary kiln at the inlet is not less than about 500 C to heat the particulate material to a temperature in the range of from about 200 C to about 900 C in a pyrolyzing atmosphere to reduce the particulate material as it moves from the one end toward the other end. The reduced particulates including char are transferred to the annular space between the inner and the outer rotating kilns near the other end of the inner rotating kiln and moved longitudinally in the annular space from near the other end toward the one end in the presence of oxygen to combust the char at an elevated temperature to produce a waste material including ash. Also, heat is provided which is transferred to the inner kiln. The waste material including ash leaves the outer rotating kiln near the one end and the pyrolysis vapor leaves through the particulate material inlet.

McIntosh, M.J.; Arzoumanidis, G.G.

1995-12-31T23:59:59.000Z

368

Microelectromechanical accelerometer with resonance-cancelling control circuit including an idle state  

DOE Patents (OSTI)

A digital feedback control circuit is disclosed for use in an accelerometer (e.g. a microelectromechanical accelerometer). The digital feedback control circuit, which periodically re-centers a proof mass in response to a sensed acceleration, is based on a sigma-delta (.SIGMA..DELTA.) configuration that includes a notch filter (e.g. a digital switched-capacitor filter) for rejecting signals due to mechanical resonances of the proof mass and further includes a comparator (e.g. a three-level comparator). The comparator generates one of three possible feedback states, with two of the feedback states acting to re-center the proof mass when that is needed, and with a third feedback state being an "idle" state which does not act to move the proof mass when no re-centering is needed. Additionally, the digital feedback control system includes an auto-zero trim capability for calibration of the accelerometer for accurate sensing of acceleration. The digital feedback control circuit can be fabricated using complementary metal-oxide semiconductor (CMOS) technology, bi-CMOS technology or bipolar technology and used in single- and dual-proof-mass accelerometers.

Chu, Dahlon D. (Albuquerque, NM); Thelen, Jr., Donald C. (Bozeman, MT); Campbell, David V. (Albuquerque, NM)

2001-01-01T23:59:59.000Z

369

Swozzle based burner tube premixer including inlet air conditioner for low emissions combustion  

DOE Patents (OSTI)

A burner for use in a combustion system of a heavy-duty industrial gas turbine includes a fuel/air premixer having an air inlet, a fuel inlet, and an annular mixing passage. The fuel/air premixer mixes fuel and air into a uniform mixture for injection into a combustor reaction zone. The burner also includes an inlet flow conditioner disposed at the air inlet of the fuel/air premixer for controlling a radial and circumferential distribution of incoming air. The pattern of perforations in the inlet flow conditioner is designed such that a uniform air flow distribution is produced at the swirler inlet annulus in both the radial and circumference directions. The premixer includes a swozzle assembly having a series of preferably air foil shaped turning vanes that impart swirl to the airflow entering via the inlet flow conditioner. Each air foil contains internal fuel flow passages that introduce natural gas fuel into the air stream via fuel metering holes that pass through the walls of the air foil shaped turning vanes. By injecting fuel in this manner, an aerodynamically clean flow field is maintained throughout the premixer. By injecting fuel via two separate passages, the fuel/air mixture strength distribution can be controlled in the radial direction to obtain optimum radial concentration profiles for control of emissions, lean blow outs, and combustion driven dynamic pressure activity as machine and combustor load are varied.

Tuthill, Richard Sterling (Bolton, CT); Bechtel, II, William Theodore (Scotia, NY); Benoit, Jeffrey Arthur (Scotia, NY); Black, Stephen Hugh (Duanesburg, NY); Bland, Robert James (Clifton Park, NY); DeLeonardo, Guy Wayne (Scotia, NY); Meyer, Stefan Martin (Troy, NY); Taura, Joseph Charles (Clifton Park, NY); Battaglioli, John Luigi (Glenville, NY)

2002-01-01T23:59:59.000Z

370

10 November 1998 Standard Applications  

E-Print Network (OSTI)

external sources, such as EPICS, VxWorks, Tcl/Tk, Interviews, and so forth. These are typically not locally

371

Renewable Energy for Water Pumping Applications In Rural Villages; Period of Performance: April 1, 2001--September 1, 2001  

DOE Green Energy (OSTI)

This report introduces conventional and renewable energy sources for water pumping applications in rural villages by reviewing the technologies and illustrating typical applications. As energy sources for water pumping, the report discusses diesel/gasoline/kerosene engines, grid power supplies, traditional windmills, electrical wind turbines, and PV.

Argaw, N.; Foster, R.; Ellis, A.

2003-07-01T23:59:59.000Z

372

Synthesis, Properties and Applications  

Science Conference Proceedings (OSTI)

Jul 15, 2013 ... Applications of nanomaterials in energy harvesting, energy storage and energy delivery. Applications to biological and chemical sensing and...

373

Postdoc Application Process  

NLE Websites -- All DOE Office Websites (Extended Search)

Program Application Process Postdoc Application Process Point your career towards LANL: work with the best minds on the planet in an inclusive environment that is rich in...

374

Approved Chemist Application 2012  

Science Conference Proceedings (OSTI)

APPROVED CHEMIST APPLICATION 1. Name of Applicant 2. Company 3. Address 4. Analyst Number (2011) 5. City 6. State 7. Postal Code

375

An Evaluation of Partitioners for Parallel SAMR Applications  

Science Conference Proceedings (OSTI)

This paper presents an experimental evaluation of a suite of dynamic partitioning/load-balancing techniques for adaptive grid hierarchies that underlie parallel structured adaptive mesh refinement applications. Partitioners evaluated include those included ...

Sumir Chandra; Manish Parashar

2001-08-01T23:59:59.000Z

376

Elastic theory of low-dimensional continua and its applications in bio- and nano-structures  

E-Print Network (OSTI)

This review presents the elastic theory of low-dimensional (one- and two-dimensional) continua and its applications in bio- and nano-structures. First, the curve and surface theory, as the geometric representation of the low-dimensional continua, is briefly described through Cartan moving frame method. The elastic theory of Kirchhoff rod, Helfrich rod, bending-soften rod, fluid membrane, and solid shell is revisited. Secondly, the application and availability of the elastic theory of low-dimensional continua in bio-structures, including short DNA rings, lipid membranes, and cell membranes, are discussed. The kink stability of short DNA rings is addressed by using the theory of Kirchhoff rod, Helfrich rod, and bending-soften rod. The lipid membranes obey the theory of fluid membrane. A cell membrane is simplified as a composite shell of lipid bilayer and membrane skeleton, which is a little similar to the solid shell. It is found that the membrane skeleton enhances highly the mechanical stability of cell membranes. Thirdly, the application and availability of the elastic theory of low-dimensional continua in nano-structures, including graphene and carbon nanotubes, are discussed. A revised Lenosky lattice model is proposed based on the local density approximation. Its continuum form up to the second order terms of curvatures and strains is the same as the free energy of 2D solid shells. Several typical mechanical properties of carbon nanotubes are revisited and investigated based on this continuum form. It is possible to avoid introducing the controversial concepts, the Young's modulus and thickness of graphene and single-walled carbon nanotubes, with this continuum form.

Z. C. Tu; Z. C. Ou-Yang

2007-06-01T23:59:59.000Z

377

Resilience: Theory and Application.  

SciTech Connect

There is strong agreement among policymakers, practitioners, and academic researchers that the concept of resilience must play a major role in assessing the extent to which various entities - critical infrastructure owners and operators, communities, regions, and the Nation - are prepared to respond to and recover from the full range of threats they face. Despite this agreement, consensus regarding important issues, such as how resilience should be defined, assessed, and measured, is lacking. The analysis presented here is part of a broader research effort to develop and implement assessments of resilience at the asset/facility and community/regional levels. The literature contains various definitions of resilience. Some studies have defined resilience as the ability of an entity to recover, or 'bounce back,' from the adverse effects of a natural or manmade threat. Such a definition assumes that actions taken prior to the occurrence of an adverse event - actions typically associated with resistance and anticipation - are not properly included as determinants of resilience. Other analyses, in contrast, include one or more of these actions in their definitions. To accommodate these different definitions, we recognize a subset of resistance- and anticipation-related actions that are taken based on the assumption that an adverse event is going to occur. Such actions are in the domain of resilience because they reduce both the immediate and longer-term adverse consequences that result from an adverse event. Recognizing resistance- and anticipation-related actions that take the adverse event as a given accommodates the set of resilience-related actions in a clear-cut manner. With these considerations in mind, resilience can be defined as: 'the ability of an entity - e.g., asset, organization, community, region - to anticipate, resist, absorb, respond to, adapt to, and recover from a disturbance.' Because critical infrastructure resilience is important both in its own right and because of its implications for community/regional resilience, it is especially important to develop a sound methodology for assessing resilience at the asset/facility level. This objective will be accomplished by collecting data on four broadly defined groups of resilience-enhancing measures: preparedness, mitigation measures, response capabilities, and recovery mechanisms. Table ES-1 illustrates how the six components that define resilience are connected to the actions that enhance the capacity of an entity to be resilient. The relationships illustrated in Table ES-1 provide the framework for developing a survey instrument that will be used to elicit the information required to assess resilience at the asset/facility level. The resilience of a community/region is a function of the resilience of its subsystems, including its critical infrastructures, economy, civil society, governance (including emergency services), and supply chains/dependencies. The number and complexity of these subsystems will make the measurement of resilience more challenging as we move from individual assets/facilities to the community/regional level (where critical infrastructure resilience is only one component). Specific challenges include uncertainty about relationships (e.g., the composition of specific supply chains), data gaps, and time and budget constraints that prevent collection of all of the information needed to construct a comprehensive assessment of the resilience of a specific community or region. These challenges can be addressed, at least partially, by adopting a 'systems approach' to the assessment of resilience. In a systems approach, the extent to which the analysis addresses the resilience of the individual subsystems can vary. Specifically, high-level systems analysis can be used to identify the most important lower-level systems. In turn, within the most important lower-level systems, site assessment data should be collected only on the most critical asset-level components about which the least is known. Implementation of the strategies outlined here to as

Carlson, J.L.; Haffenden, R.A.; Bassett, G.W.; Buehring, W.A.; Collins, M.J., III; Folga, S.M.; Petit, F.D.; Phillips, J.A.; Verner, D.R.; Whitfield, R.G. (Decision and Information Sciences)

2012-02-03T23:59:59.000Z

378

X-ray Thomson scattering for partially ionized plasmas including the effect of bound levels  

E-Print Network (OSTI)

X-ray Thomson scattering is being developed as a method to measure the temperature, electron density, and ionization state of high energy density plasmas such as those used in inertial confinement fusion. Most experiments are currently done at large laser facilities that can create bright X-ray sources, however the advent of the X-ray free electron laser (X-FEL) provides a new bright source to use in these experiments. One challenge with X-ray Thomson scattering experiments is understanding how to model the scattering for partially ionized plasmas in order to include the contributions of the bound electrons in the scattered intensity. In this work we take the existing models of Thomson scattering that include elastic ion-ion scattering and the electron-electron plasmon scattering and add the contribution of the bound electrons in the partially ionized plasmas. We validated our model by analyzing existing beryllium experimental data. We then consider several higher Z materials such as Cr and predict the existe...

Nilsen, J; Cheng, K T

2013-01-01T23:59:59.000Z

379

Segmented instrumentation tube including a locking sleeve for interlocking the segments of the instrumentation tube  

DOE Patents (OSTI)

Segmented instrumentation tube including a locking sleeve for interlocking the segments of the instrumentation tube, so that the threaded ends of the instrumentation tube do not unthread when subjected to vibration, such an instrumentation tube being suitable for use in a nuclear reactor pressure vessel. The instrumentation tube has a first member having a threaded end portion that has a plurality of first holes circumferentially around the outside surface thereof. The instrumentation tube also has a second member having a threaded end portion that has a plurality of second holes circumferentially around the outside surface thereof. The threads of the second member are caused to threadably engage the threads of the first member for defining a threaded joint therebetween. A sleeve having an inside surface surrounds the end portion of the first member and the end portion of the second member and thus surrounds the threaded joint. The sleeve includes a plurality of first projections and second projections that outwardly extend from the inside surface to engage the first holes and the second holes, respectively. The outside surface of the sleeve is crimped or swaged at the locations of the first projections and second projections such that the first projections and the second projections engage their respective holes. In this manner, independent rotation of the first member with respect to the second member is prevented, so that the instrumentation tube will not unthread at its threaded joint.

Obermeyer, Franklin D. (Pensacola, FL)

1993-01-01T23:59:59.000Z

380

An Evaluation of Molten-Salt Power Towers Including Results of the Solar Two Project  

DOE Green Energy (OSTI)

This report utilizes the results of the Solar Two project, as well as continuing technology development, to update the technical and economic status of molten-salt power towers. The report starts with an overview of power tower technology, including the progression from Solar One to the Solar Two project. This discussion is followed by a review of the Solar Two project--what was planned, what actually occurred, what was learned, and what was accomplished. The third section presents preliminary information regarding the likely configuration of the next molten-salt power tower plant. This section draws on Solar Two experience as well as results of continuing power tower development efforts conducted jointly by industry and Sandia National Laboratories. The fourth section details the expected performance and cost goals for the first commercial molten-salt power tower plant and includes a comparison of the commercial performance goals to the actual performance at Solar One and Solar Two. The final section summarizes the successes of Solar Two and the current technology development activities. The data collected from the Solar Two project suggest that the electricity cost goals established for power towers are reasonable and can be achieved with some simple design improvements.

REILLY, HUGH E.; KOLB, GREGORY J.

2001-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Segmented instrumentation tube including a locking sleeve for interlocking the segments of the instrumentation tube  

DOE Patents (OSTI)

Segmented instrumentation tube including a locking sleeve for interlocking the segments of the instrumentation tube, so that the threaded ends of the instrumentation tube do not unthread when subjected to vibration, such an instrumentation tube being suitable for use in a nuclear reactor pressure vessel. The instrumentation tube has a first member having a threaded end portion that has a plurality of first holes circumferentially around the outside surface thereof. The instrumentation tube also has a second member having a threaded end portion that has a plurality of second holes circumferentially around the outside surface thereof. The threads of the second member are caused to threadably engage the threads of the first member for defining a threaded joint there between. A sleeve having an inside surface surrounds the end portion of the first member and the end portion of the second member and thus surrounds the threaded joint. The sleeve includes a plurality of first projections and second projections that outwardly extend from the inside surface to engage the first holes and the second holes, respectively. The outside surface of the sleeve is crimped or swaged at the locations of the first projections and second projections such that the first projections and the second projections engage their respective holes. In this manner, independent rotation of the first member with respect to the second member is prevented, so that the instrumentation tube will not unthread at its threaded joint. 10 figures.

Obermeyer, F.D.

1993-11-16T23:59:59.000Z

382

Dye laser amplifier including an improved window configuration for its dye beam  

DOE Patents (OSTI)

A dye laser amplifier in which a continuously replenished supply of dye is excited with a first light beam in order to amplify the intensity of a second different light beam passing therethrough is disclosed herein. This amplifier includes a cell though which a continuous stream of the dye is caused to pass, and means for directing the first beam into the cell while the second beam is directed into and through the same cell. There is also disclosed herein a specific improvement to this amplifier which resides in the use of a pair of particularly configured windows through which the second beam passes along fixed paths as the second beam enters and exits the dye cell. Each of these windows has a relatively thick main section which is substantially larger in dimensions transverse to its beam path than the cross section of the second beam itself, whereby to add structural integrity to the overall window. At the same time, the latter includes a second section which is disposed entirely within the confines of the main section and through which the second beam is intended to pass in its entirety. This second section is made substantially thinner than the main section in order to reduce optical distortion as the second beam passes therethrough.

O' Neil, Richard W. (Pleasanton, CA); Davin, James M. (Livermore, CA)

1992-01-01T23:59:59.000Z

383

Dye laser amplifier including an improved window configuration for its dye beam  

DOE Patents (OSTI)

A dye laser amplifier in which a continuously replenished supply of dye is excited with a first light beam in order to amplify the intensity of a second different light beam passing therethrough is disclosed herein. This amplifier includes a cell though which a continuous stream of the dye is caused to pass, and means for directing the first beam into the cell while the second beam is directed into and through the same cell. There is also disclosed herein a specific improvement to this amplifier which resides in the use of a pair of particularly configured windows through which the second beam passes along fixed paths as the second beam enters and exits the dye cell. Each of these windows has a relatively thick main section which is substantially larger in dimensions transverse to its beam path than the cross section of the second beam itself, whereby to add structural integrity to the overall window. At the same time, the latter includes a second section which is disposed entirely within the confines of the main section and through which the second beam is intended to pass in its entirety. This second section is made substantially thinner than the main section in order to reduce optical distortion as the second beam passes therethrough. 4 figs.

O' Neil, R.W.; Davin, J.M.

1992-12-01T23:59:59.000Z

384

Applications of Commercial Heat Pump Water Heaters in Hot, Humid Climates  

E-Print Network (OSTI)

Heat pump water heaters can provide high-efficiency water heating and supplemental space cooling and dehumidification in commercial buildings throughout the United States. They are particularly attractive in hot, humid areas where cooling loads are high and the cooling season is long. Because commercial kitchens and laundry facilities have simultaneous water heating and cooling needs, they are excellent applications for heat pump water heaters. Typical heat pump water heaters (HPWHs) operate at an annual coefficient of performance (COP) of approximately 3.0 for water heating alone. Space conditioning benefits of about 0.67 Btu are delivered at no additional cost for each Btu of water heating output. In situations in which this cooling output is valued, the dual thermal outputs for heating and cooling make heat pump water heaters particularly attractive. The comfort value of added cooling in overheated facilities and the resulting increase in employee and customer satisfaction are frequently cited as additional benefits. This paper describes currently available heat pump water heating equipment and offers guidelines for successful applications in commercial facilities. The results of field test programs involving more than 100 units in Alabama, Georgia, Mississippi, Tennessee, South Carolina, and other areas are incorporated. Initial conclusions are drawn from a reliability database, and interviews with utility applications specialists and manufacturers are discussed. Design tools are reviewed, including a new comprehensive computer simulation model. Emphasis is placed on identifying sound candidates for installations and on application and design considerations. A brief survey is provided of environmental implications of heat pump water heaters and new developments in heat pump water heater equipment.

Johnson, K. F.; Shedd, A. C.

1992-05-01T23:59:59.000Z

385

Benefit/cost comparisons of SMES in system-specific application scenarios  

DOE Green Energy (OSTI)

The inherently high storage efficiency, instantaneous dispatch capability and multi-function uses of superconducting magnetic energy storage (SMES) are attributes that give it the potential for widespread application in the electric utility industry. Opportunities appear to exist where SMES at a given location could provide multiple benefits either simultaneously or sequentially as system conditions dictate. These benefits, including diurnal storage and system stability and dynamic control enhancement, increase the application potential of SMES to a larger number of opportunities than might be justified by the value of its diurnal storage capability alone. However, the benefits an individual utility may realize from SMES applications are strongly influenced by the characteristics of the utility system, the location of the SMES unit and the timing of its installation in the system. Such benefits are typically not evaluated adequately in generic studies. This paper summarizes results of case studies performed by Pacific Northwest Laboratory (PNL) with funding provided by the Bonneville Power Administration (BPA) and the Electric Power Research Institute (EPRI). The derivation of SMES benefits and costs are described and benefit/cost (B/C) ratios are compared in system-specific scenarios of interest to BPA. Results of using the DYNASTORE production cost model show the sensitivity of B/C ratios to SMES capacity and power and to the forecast system load. Intermediate-size SMES applications which primarily provide system stability and dynamic control enhancement are reviewed. The potential for SMES to levelize the output of a wind energy complex is also assessed. Most of the cases show SMES to provide a positive net benefit with the additional, sometimes surprising indication, that B/C ratios and net present worth of intermediate-size units can exceed those of larger systems.

De Steese, J.G.; Dagle, J.E.; Kreid, D.K. [Pacific Northwest Lab., Richland, WA (United States); Haner, J.M.; Myers, W.E. [Bonneville Power Administration, Portland, OR (United States)

1992-09-01T23:59:59.000Z

386

Industrial Applications of Renewable Resources  

Science Conference Proceedings (OSTI)

Archive of Industrial Applications of Renewable Resources Industrial Applications of Renewable Resources Cincinnati, Ohio, USA Industrial Applications of Renewable Resources ...

387

Improving scalability of Bag-of-Tasks applications running on master-slave platforms  

Science Conference Proceedings (OSTI)

Bag-of-Tasks applications are parallel applications composed of independent tasks. Examples of Bag-of-Tasks (BoT) applications include Monte Carlo simulations, massive searches (such as key breaking), image manipulation applications and data mining algorithms. ... Keywords: Bag-of-Tasks applications, Master-slave platforms, Scalability analysis

Fabr?cio A. B. da Silva; Hermes Senger

2009-02-01T23:59:59.000Z

388

High-temperature superconductor current leads for electric utility SMES applications  

DOE Green Energy (OSTI)

Current leads that utilize high-temperature superconductors (HTSS) to deliver power to devices operating at liquid helium temperature have the potential to reduce refrigeration requirements to levels significantly below those achievable with conventional leads. As part of the US Department of Energy`s Superconductivity Technology Program, Argonne National Laboratory and two industrial partners are developing HTS current leads for application to superconducting magnetic energy storage (SMES) systems. Superconductivity, Inc. (SI) is a supplier of micro-SMES systems for power-quality applications. A typical SI SMES system has an 0.3-kWh energy capacity and operates at currents up to 1.2 k.A. The Babcock & Wilcox Company (B&W) is engaged in a project to design, build, and demonstrate a midsized SMES system. The B&W system has an 0.5-MWh energy capacity and operates at currents up to 16 kA. Details of the lead designs. including materials, configuration and performance predictions. are presented.

Niemann, R.C.; Cha, Y.S.; Hull, J.R. [Argonne National Lab., IL (United States); Buckles, W.E.; Weber, B.R. [Superconductivity, Inc., Madison, WI (United States); Dixon, K.D.; Rey, C.M. [Babcock and Wilcox Company, Lynchburg, VA (United States). Naval Nuclear Fuel Div.

1995-07-01T23:59:59.000Z

389

Electric Field Induced Rotation of Polymer Cholesteric Liquid Crystal Flakes: Mechanisms and Applications  

DOE Green Energy (OSTI)

Electric fields can induce motion of polymer cholesteric liquid crystal (pCLC) flakes suspended in a fluid medium. The platelet-shaped pCLC flakes with a Grandjean texture show strong selective reflection when lying flat in the plane of a conventional cell. As their orientation with respect to normally incident light changes, their selective reflection color shifts toward the blue and diminishes until the flakes are no longer easily visible beyond 7-12{sup o} of rotation. Reproducibility and control of motion has been observed in moderately conductive host fluid. Flakes in such hosts do not respond to a DC electric field, but they rotate 90{sup o} in an AC field within a given frequency band. The response times and frequency regions for motion depend partially on the field magnitude, the dielectric properties of the host fluid and the flake geometry. We observe flakes reorienting in less than 500 ms in an electric field of 0.17 Vrms/mm, while subsecond reorientation is seen in fields as low as 5 x 10-2 Vrms/mm. This response time is comparable with typical electronic-paper applications, but with a significantly lower electric field. Displays using pCLC flakes would not require backlighting, sheet polarizers, color filters or alignment layers. Numerous additional applications for pCLC flakes are envisioned, including filters, polarizers, and spatial light modulators.

Kosc, T. Z.; Marshall, K. L.; Jacobs, S. D.; Lambropoulous, J. C.

2002-12-31T23:59:59.000Z

390

Level: National and Regional Data; Row: End Uses; Column: Energy Sources, including Net Demand for Electricity;  

U.S. Energy Information Administration (EIA) Indexed Site

7 End Uses of Fuel Consumption, 2006; 7 End Uses of Fuel Consumption, 2006; Level: National and Regional Data; Row: End Uses; Column: Energy Sources, including Net Demand for Electricity; Unit: Physical Units or Btu. Distillate Coal Fuel Oil (excluding Coal Net Demand Residual and Natural Gas(c) LPG and Coke and Breeze) for Electricity(a) Fuel Oil Diesel Fuel(b) (billion NGL(d) (million End Use (million kWh) (million bbl) (million bbl) cu ft) (million bbl) short tons) Total United States TOTAL FUEL CONSUMPTION 977,338 40 22 5,357 21 46 Indirect Uses-Boiler Fuel 24,584 21 4 2,059 2 25 Conventional Boiler Use 24,584 11 3 1,245 2 6 CHP and/or Cogeneration Process 0 10 1 814 * 19 Direct Uses-Total Process 773,574 10 9 2,709 10 19 Process Heating

391

Level: National and Regional Data; Row: End Uses; Column: Energy Sources, including Net Electricity;  

U.S. Energy Information Administration (EIA) Indexed Site

5 End Uses of Fuel Consumption, 2006; 5 End Uses of Fuel Consumption, 2006; Level: National and Regional Data; Row: End Uses; Column: Energy Sources, including Net Electricity; Unit: Physical Units or Btu. Distillate Coal Fuel Oil (excluding Coal Net Residual and Natural Gas(c) LPG and Coke and Breeze) Total Electricity(a) Fuel Oil Diesel Fuel(b) (billion NGL(d) (million Other(e) End Use (trillion Btu) (million kWh) (million bbl) (million bbl) cu ft) (million bbl) short tons) (trillion Btu) Total United States TOTAL FUEL CONSUMPTION 15,658 835,382 40 22 5,357 21 46 5,820 Indirect Uses-Boiler Fuel -- 12,109 21 4 2,059 2 25 -- Conventional Boiler Use 12,109 11 3 1,245 2 6 CHP and/or Cogeneration Process 0 10 1 814 * 19 Direct Uses-Total Process

392

Including Alternative Resources in State Renewable Portfolio Standards: Current Design and Implementation Experience  

SciTech Connect

Currently, 29 states, the District of Columbia, and Puerto Rico have instituted a renewable portfolio standard (RPS). An RPS sets a minimum threshold for how much renewable energy must be generated in a given year. Each state policy is unique, varying in percentage targets, timetables, and eligible resources. This paper examines state experience with implementing renewable portfolio standards that include energy efficiency, thermal resources, and non-renewable energy and explores compliance experience, costs, and how states evaluate, measure, and verify energy efficiency and convert thermal energy. It aims to gain insights from the experience of states for possible federal clean energy policy as well as to share experience and lessons for state RPS implementation.

Heeter, J.; Bird, L.

2012-11-01T23:59:59.000Z

393

Level: National and Regional Data; Row: End Uses; Column: Energy Sources, including Net Electricity;  

U.S. Energy Information Administration (EIA) Indexed Site

6 End Uses of Fuel Consumption, 2006; 6 End Uses of Fuel Consumption, 2006; Level: National and Regional Data; Row: End Uses; Column: Energy Sources, including Net Electricity; Unit: Trillion Btu. Distillate Fuel Oil Coal Net Residual and LPG and (excluding Coal End Use Total Electricity(a) Fuel Oil Diesel Fuel(b) Natural Gas(c) NGL(d) Coke and Breeze) Other(e) Total United States TOTAL FUEL CONSUMPTION 15,658 2,850 251 129 5,512 79 1,016 5,820 Indirect Uses-Boiler Fue -- 41 133 23 2,119 8 547 -- Conventional Boiler Use 41 71 17 1,281 8 129 CHP and/or Cogeneration Process 0 62 6 838 1 417 Direct Uses-Total Process -- 2,244 62 52 2,788 39 412 -- Process Heating -- 346 59 19 2,487 32 345 -- Process Cooling and Refrigeration -- 206 * 1 32 * * -- Machine Drive

394

Level: National Data; Row: End Uses within NAICS Codes; Column: Energy Sources, including Net Electricity;  

U.S. Energy Information Administration (EIA) Indexed Site

2 End Uses of Fuel Consumption, 2006; 2 End Uses of Fuel Consumption, 2006; Level: National Data; Row: End Uses within NAICS Codes; Column: Energy Sources, including Net Electricity; Unit: Trillion Btu. Distillate Fuel Oil Coal NAICS Net Residual and LPG and (excluding Coal Code(a) End Use Total Electricity(b) Fuel Oil Diesel Fuel(c) Natural Gas(d) NGL(e) Coke and Breeze) Other(f) Total United States 311 - 339 ALL MANUFACTURING INDUSTRIES TOTAL FUEL CONSUMPTION 15,658 2,850 251 129 5,512 79 1,016 5,820 Indirect Uses-Boiler Fuel -- 41 133 23 2,119 8 547 -- Conventional Boiler Use -- 41 71 17 1,281 8 129 -- CHP and/or Cogeneration Process -- -- 62 6 838 1 417 -- Direct Uses-Total Process -- 2,244 62 52 2,788 39 412 -- Process Heating -- 346 59 19 2,487

395

Level: National and Regional Data; Row: End Uses; Column: Energy Sources, including Net Demand for Electricity;  

U.S. Energy Information Administration (EIA) Indexed Site

Next MECS will be conducted in 2010 Table 5.8 End Uses of Fuel Consumption, 2006; Level: National and Regional Data; Row: End Uses; Column: Energy Sources, including Net Demand for Electricity; Unit: Trillion Btu. Distillate Fuel Oil Coal Net Demand Residual and LPG and (excluding Coal End Use for Electricity(a) Fuel Oil Diesel Fuel(b) Natural Gas(c) NGL(d) Coke and Breeze) Total United States TOTAL FUEL CONSUMPTION 3,335 251 129 5,512 79 1,016 Indirect Uses-Boiler Fuel 84 133 23 2,119 8 547 Conventional Boiler Use 84 71 17 1,281 8 129 CHP and/or Cogeneration Process 0 62 6 838 1 417 Direct Uses-Total Process 2,639 62 52 2,788 39 412 Process Heating 379 59 19 2,487 32 345 Process Cooling and Refrigeration

396

Level: National Data; Row: End Uses within NAICS Codes; Column: Energy Sources, including Net Electricity;  

U.S. Energy Information Administration (EIA) Indexed Site

1 End Uses of Fuel Consumption, 2006; 1 End Uses of Fuel Consumption, 2006; Level: National Data; Row: End Uses within NAICS Codes; Column: Energy Sources, including Net Electricity; Unit: Physical Units or Btu. Distillate Coal Fuel Oil (excluding Coal Net Residual and Natural Gas(d) LPG and Coke and Breeze) NAICS Total Electricity(b) Fuel Oil Diesel Fuel(c) (billion NGL(e) (million Other(f) Code(a) End Use (trillion Btu) (million kWh) (million bbl) (million bbl) cu ft) (million bbl) short tons) (trillion Btu) Total United States 311 - 339 ALL MANUFACTURING INDUSTRIES TOTAL FUEL CONSUMPTION 15,658 835,382 40 22 5,357 21 46 5,820 Indirect Uses-Boiler Fuel -- 12,109 21 4 2,059 2 25 -- Conventional Boiler Use -- 12,109 11 3 1,245 2 6 -- CHP and/or Cogeneration Process

397

Theory, design, and operation of liquid metal fast breeder reactors, including operational health physics  

SciTech Connect

A comprehensive evaluation was conducted of the radiation protection practices and programs at prototype LMFBRs with long operational experience. Installations evaluated were the Fast Flux Test Facility (FFTF), Richland, Washington; Experimental Breeder Reactor II (EBR-II), Idaho Falls, Idaho; Prototype Fast Reactor (PFR) Dounreay, Scotland; Phenix, Marcoule, France; and Kompakte Natriumgekuhlte Kernreak Toranlange (KNK II), Karlsruhe, Federal Republic of Germany. The evaluation included external and internal exposure control, respiratory protection procedures, radiation surveillance practices, radioactive waste management, and engineering controls for confining radiation contamination. The theory, design, and operating experience at LMFBRs is described. Aspects of LMFBR health physics different from the LWR experience in the United States are identified. Suggestions are made for modifications to the NRC Standard Review Plan based on the differences.

Adams, S.R.

1985-10-01T23:59:59.000Z

398

Including the Effects of Electronic Excitations and Electron-Phonon Coupling in Cascade Simulations  

SciTech Connect

Radiation damage has traditionally been modeled using cascade simulations however such simulations generally neglect the effects of electron-ion interactions, which may be significant in high energy cascades. A model has been developed which includes the effects of electronic stopping and electron-phonon coupling in Molecular Dynamics simulations by means of an inhomogeneous Langevin thermostat. The energy lost by the atoms to electronic excitations is gained by the electronic system and the energy evolution of the electronic system is modeled by the heat diffusion equation. Energy is exchanged between the electronic system and the atoms in the Molecular Dynamics simulation by means of a Langevin thermostat, the temperature of which is the local electronic temperature. The model is applied to a 10 keV cascade simulation for Fe. (authors)

Duffy, Dorothy [Physics and Astronomy, UCL, London (United Kingdom)]|[EURATOM/UKAEA Fusion Association, Culham Science Centre, Oxfordshire (United Kingdom); Rutherford, Alexis [Physics and Astronomy, UCL, London (United Kingdom)

2008-07-01T23:59:59.000Z

399

Dispersion in a thermal plasma including arbitrary degeneracy and quantum recoil  

Science Conference Proceedings (OSTI)

The longitudinal response function for a thermal electron gas is calculated including two quantum effects exactly, degeneracy, and the quantum recoil. The Fermi-Dirac distribution is expanded in powers of a parameter that is small in the nondegenerate limit and the response function is evaluated in terms of the conventional plasma dispersion function to arbitrary order in this parameter. The infinite sum is performed in terms of polylogarithms in the long-wavelength and quasistatic limits, giving results that apply for arbitrary degeneracy. The results are applied to the dispersion relations for Langmuir waves and to screening, reproducing known results in the nondegenerate and completely degenerate limits, and generalizing them to arbitrary degeneracy.

Melrose, D. B. [School of Physics, University of Sydney, New South Wales 2006 (Australia); Mushtaq, A. [School of Physics, University of Sydney, New South Wales 2006 (Australia); Theoretical Plasma Physics Division, PINSTECH, Nilore, 44000 Islamabad (Pakistan)

2010-11-15T23:59:59.000Z

400

Engine including hydraulically actuated valvetrain and method of valve overlap control  

DOE Patents (OSTI)

An exhaust valve control method may include displacing an exhaust valve in communication with the combustion chamber of an engine to an open position using a hydraulic exhaust valve actuation system and returning the exhaust valve to a closed position using the hydraulic exhaust valve actuation assembly. During closing, the exhaust valve may be displaced for a first duration from the open position to an intermediate closing position at a first velocity by operating the hydraulic exhaust valve actuation assembly in a first mode. The exhaust valve may be displaced for a second duration greater than the first duration from the intermediate closing position to a fully closed position at a second velocity at least eighty percent less than the first velocity by operating the hydraulic exhaust valve actuation assembly in a second mode.

Cowgill, Joel (White Lake, MI)

2012-05-08T23:59:59.000Z

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Flexible barrier film, method of forming same, and organic electronic device including same  

DOE Patents (OSTI)

A flexible barrier film has a thickness of from greater than zero to less than 5,000 nanometers and a water vapor transmission rate of no more than 1.times.10.sup.-2 g/m.sup.2/day at 22.degree. C. and 47% relative humidity. The flexible barrier film is formed from a composition, which comprises a multi-functional acrylate. The composition further comprises the reaction product of an alkoxy-functional organometallic compound and an alkoxy-functional organosilicon compound. A method of forming the flexible barrier film includes the steps of disposing the composition on a substrate and curing the composition to form the flexible barrier film. The flexible barrier film may be utilized in organic electronic devices.

Blizzard, John; Tonge, James Steven; Weidner, William Kenneth

2013-03-26T23:59:59.000Z

402

A high liquid yield process for retorting various organic materials including oil shale  

DOE Patents (OSTI)

This invention is a continuous retorting process for various high molecular weight organic materials, including oil shale, that yields an enhanced output of liquid product. The organic material, mineral matter, and an acidic catalyst, that appreciably adsorbs alkenes on surface sites at prescribed temperatures, are mixed and introduced into a pyrolyzer. A circulating stream of olefin enriched pyrolysis gas is continuously swept through the organic material and catalyst, whereupon, as the result of pyrolysis, the enhanced liquid product output is provided. Mixed spent organic material, mineral matter, and cool catalyst are continuously withdrawn from the pyrolyzer. Combustion of the spent organic material and mineral matter serves to reheat the catalyst. Olefin depleted pyrolysis gas, from the pyrolyzer, is enriched in olefins and recycled into the pyrolyzer. The reheated acidic catalyst is separated from the mineral matter and again mixed with fresh organic material, to maintain the continuously cyclic process. 2 figs.

Coburn, T.T.

1988-07-26T23:59:59.000Z

403

High liquid yield process for retorting various organic materials including oil shale  

DOE Patents (OSTI)

This invention is a continuous retorting process for various high molecular weight organic materials, including oil shale, that yields an enhanced output of liquid product. The organic material, mineral matter, and an acidic catalyst, that appreciably adsorbs alkenes on surface sites at prescribed temperatures, are mixed and introduced into a pyrolyzer. A circulating stream of olefin enriched pyrolysis gas is continuously swept through the organic material and catalyst, whereupon, as the result of pyrolysis, the enhanced liquid product output is provided. Mixed spent organic material, mineral matter, and cool catalyst are continuously withdrawn from the pyrolyzer. Combustion of the spent organic material and mineral matter serves to reheat the catalyst. Olefin depleted pyrolysis gas, from the pyrolyzer, is enriched in olefins and recycled into the pyrolyzer. The reheated acidic catalyst is separated from the mineral matter and again mixed with fresh organic material, to maintain the continuously cyclic process.

Coburn, Thomas T. (Livermore, CA)

1990-01-01T23:59:59.000Z

404

Estimating parameters of coalescing compact binaries with a detector network including LIGO Australia  

E-Print Network (OSTI)

One of the goals of gravitational-wave astronomy is simultaneous detection of gravitational-wave signals from merging compact-object binaries and the electromagnetic transients from these mergers. With the next generation of advanced ground-based gravitational wave detectors under construction, we examine the benefits of the proposed extension of the detector network to include a fourth site in Australia in addition to the network of Hanford, Livingston and Cascina sites. Using Bayesian parameter-estimation analyses of simulated gravitational-wave signals from a range of coalescing-binary locations and orientations, we study the improvement in parameter estimation. We find that an Australian detector can break degeneracies in several parameters; in particular, the localization of the source on the sky is improved by a factor of ~4, with more modest improvements in distance and binary inclination estimates. This enhanced ability to localize sources on the sky will be crucial in any search for electromagnetic c...

Aylott, Benjamin; Kalogera, Vassiliki; Mandel, Ilya; Raymond, Vivien; Rodriguez, Carl; van der Sluys, Marc; Vecchio, Alberto; Veitch, John

2011-01-01T23:59:59.000Z

405

The Food Crises: A quantitative model of food prices including speculators and ethanol conversion  

E-Print Network (OSTI)

Recent increases in basic food prices are severely impacting vulnerable populations worldwide. Proposed causes such as shortages of grain due to adverse weather, increasing meat consumption in China and India, conversion of corn to ethanol in the US, and investor speculation on commodity markets lead to widely differing implications for policy. A lack of clarity about which factors are responsible reinforces policy inaction. Here, for the first time, we construct a dynamic model that quantitatively agrees with food prices. The results show that the dominant causes of price increases are investor speculation and ethanol conversion. Models that just treat supply and demand are not consistent with the actual price dynamics. The two sharp peaks in 2007/2008 and 2010/2011 are specifically due to investor speculation, while an underlying upward trend is due to increasing demand from ethanol conversion. The model includes investor trend following as well as shifting between commodities, equities and bonds to take ad...

Lagi, Marco; Bertrand, Karla Z; Bar-Yam, Yaneer

2011-01-01T23:59:59.000Z

406

Dye laser amplifier including a low turbulence, stagnation-free dye flow configuration  

DOE Patents (OSTI)

A large (high flow rate) dye laser amplifier in which a continuous replenished supply of dye is excited by a first light beam, specifically a copper vapor laser beam, in order to amplify the intensity of a second different light beam, specifically a dye beam, passing through the dye is disclosed herein. This amplifier includes a dye cell defining a dye chamber through which a continuous stream of dye is caused to pass at a flow rate of for example 30 gallons/minute, a specifically designed support vessel for containing the dye cell and a screen device for insuring that the dye stream passes into the dye cell in a substantially turbulent free, stagnation-free manner.

Davin, James (Gilroy, CA)

1992-01-01T23:59:59.000Z

407

Solar photovoltaics for development applications  

DOE Green Energy (OSTI)

This document introduces photovoltaic technology to individuals and groups specializing in development activities. Examples of actual installations illustrate the many services supplied by photovoltaic systems in development applications, including water pumping, lighting, health care, refrigeration, communications, and a variety of productive uses. The various aspects of the technology are explored to help potential users evaluate whether photovoltaics can assist them in achieving their organizational goals. Basic system design, financing techniques, and the importance of infrastructure are included, along with additional sources of information and major US photovoltaic system suppliers.

Shepperd, L.W. [Florida Solar Energy Center, Cape Canaveral, FL (United States)] [Florida Solar Energy Center, Cape Canaveral, FL (United States); Richards, E.H. [Sandia National Labs., Albuquerque, NM (United States)] [Sandia National Labs., Albuquerque, NM (United States)

1993-08-01T23:59:59.000Z

408

Nonleptonic two-body B decays including axial-vector mesons in the final state  

SciTech Connect

We present a systematic study of exclusive charmless nonleptonic two-body B decays including axial-vector mesons in the final state. We calculate branching ratios of B{yields}PA, VA, and AA decays, where A, V, and P denote an axial vector, a vector, and a pseudoscalar meson, respectively. We assume a naive factorization hypothesis and use the improved version of the nonrelativistic Isgur-Scora-Grinstein-Wise quark model for form factors in B{yields}A transitions. We include contributions that arise from the effective {delta}B=1 weak Hamiltonian H{sub eff}. The respective factorized amplitudes of these decays are explicitly shown and their penguin contributions are classified. We find that decays B{sup -}{yields}a{sub 1}{sup 0}{pi}{sup -}, B{sup 0}{yields}a{sub 1}{sup {+-}}{pi}{sup {+-}}, B{sup -}{yields}a{sub 1}{sup -}K{sup 0}, B{sup 0}{yields}a{sub 1}{sup +}K{sup -}, B{sup 0}{yields}f{sub 1}K{sup 0}, B{sup -}{yields}f{sub 1}K{sup -}, B{sup -}{yields}K{sub 1}{sup -}(1400){eta}{sup (')}, B{sup -}{yields}b{sub 1}{sup -}K{sup 0}, and B{sup 0}{yields}b{sub 1}{sup +}{pi}{sup -}(K{sup -}) have branching ratios of the order of 10{sup -5}. We also study the dependence of branching ratios for B{yields}K{sub 1}P(V,A) decays [K{sub 1}=K{sub 1}(1270), K{sub 1}(1400)] with respect to the mixing angle between K{sub 1A} and K{sub 1B}.

Calderon, G.; Munoz, J. H.; Vera, C. E. [Facultad de Ingenieria Mecanica y Electrica, Universidad Autonoma de Coahuila, CP 27000, Torreon, Coahuila (Mexico); Departamento de Fisica, Universidad del Tolima, Apartado Aereo 546, Ibague (Colombia)

2007-11-01T23:59:59.000Z

409

Including realistic tidal deformations in binary black-hole initial data  

E-Print Network (OSTI)

A shortcoming of current binary black-hole initial data is the generation of spurious gravitational radiation, so-called junk radiation, when they are evolved. This problem is a consequence of an oversimplified modeling of the binary's physics in the initial data. Since junk radiation is not astrophysically realistic, it contaminates the actual waveforms of interest and poses a numerical nuisance. The work here presents a further step towards mitigating and understanding the origin of this issue, by incorporating post-Newtonian results in the construction of constraint-satisfying binary black-hole initial data. Here we focus on including realistic tidal deformations of the black holes in the initial data, by building on the method of superposing suitably chosen black hole metrics to compute the conformal data. We describe the details of our initial data for an equal-mass and nonspinning binary, compute the subsequent relaxation of horizon quantities in evolutions, and quantify the amount of junk radiation that is generated. These results are contrasted with those obtained with the most common choice of conformally flat (CF) initial data, as well as superposed Kerr-Schild (SKS) initial data. We find that when realistic tidal deformations are included, the early transients in the horizon geometries are significantly reduced, along with smaller deviations in the relaxed black hole masses and spins from their starting values. Likewise, the junk radiation content in the $l=2$ modes is reduced by a factor of $\\sim$1.7 relative to CF initial data, but only by a factor of $\\sim$1.2 relative to SKS initial data. More prominently, the junk radiation content in the $3\\leq l\\leq8$ modes is reduced by a factor of $\\sim$5 relative to CF initial data, and by a factor of $\\sim$2.4 relative to SKS initial data.

Tony Chu

2013-10-29T23:59:59.000Z

410

RDI's Wisdom Way Solar Village Final Report: Includes Utility Bill Analysis of Occupied Homes  

SciTech Connect

In 2010, Rural Development, Inc. (RDI) completed construction of Wisdom Way Solar Village (WWSV), a community of ten duplexes (20 homes) in Greenfield, MA. RDI was committed to very low energy use from the beginning of the design process throughout construction. Key features include: 1. Careful site plan so that all homes have solar access (for active and passive); 2. Cellulose insulation providing R-40 walls, R-50 ceiling, and R-40 floors; 3. Triple-pane windows; 4. Airtight construction (~0.1 CFM50/ft2 enclosure area); 5. Solar water heating systems with tankless, gas, auxiliary heaters; 6. PV systems (2.8 or 3.4kWSTC); 7. 2-4 bedrooms, 1,100-1,700 ft2. The design heating loads in the homes were so small that each home is heated with a single, sealed-combustion, natural gas room heater. The cost savings from the simple HVAC systems made possible the tremendous investments in the homes' envelopes. The Consortium for Advanced Residential Buildings (CARB) monitored temperatures and comfort in several homes during the winter of 2009-2010. In the Spring of 2011, CARB obtained utility bill information from 13 occupied homes. Because of efficient lights, appliances, and conscientious home occupants, the energy generated by the solar electric systems exceeded the electric energy used in most homes. Most homes, in fact, had a net credit from the electric utility over the course of a year. On the natural gas side, total gas costs averaged $377 per year (for heating, water heating, cooking, and clothes drying). Total energy costs were even less - $337 per year, including all utility fees. The highest annual energy bill for any home evaluated was $458; the lowest was $171.

Robb Aldrich, Steven Winter Associates

2011-07-01T23:59:59.000Z

411

Multimedia Resources, including the CMS Eye, from the Compact Muon Solenoid (CMS) Experiment at CERN  

DOE Data Explorer (OSTI)

The Compact Muon Solenoid (CMS) experiment is one of two large general-purpose particle physics detectors built on the proton-proton Large Hadron Collider (LHC) at CERN in Switzerland and France. The CMS detector is located in an underground cavern at Cessy in France. The CMS detector will study many aspects of proton collisions at 14 TeV, the center-of-mass energy of the LHC particle accelerator. [from http://en.wikipedia.org/wiki/Compact_Muon_Solenoid]

The US CMS collaboration, with 48 institutions, 420 Ph.D. physicists, over 100 graduate students, and nearly 200 engineers, technicians, and computer scientists is the largest national group in the CMS collaboration. US groups have made significant contributions to nearly every aspect of the detector throughout all phases including construction, installation and preparation for data-taking. The US collaboration also made major contributions to the construction and operation of the computing facilities needed to analyze the unprecedented amount of data to be generated by CMS. This work includes the software that allows physicists to operate the CMS detector, reconstruct the data, analyze it and extract new physics.

The CMS media website from CERN provides images, videos, presentations, and the CMS Eye, a system of webcams looking into the underground cavern at Cessy, into the control room, and even out of the window of the control room at the village of Cessy and the Jura Mountains. Many event displays are available in the image collections, as well as the CMS Photo Book covering 1998 2008 when CMS was being assembled, installed, and commissioned.

US-LHC and the International CMS Collaboration

412

Solid-State Transfer Switch Technology and Application Update  

Science Conference Proceedings (OSTI)

Static transfer switches are used to switch between multiple voltage sources. Most legacy transfer switches typically use electromechanical devices, and some use thyristors. The advent of advanced high-voltage power semiconductors has allowed the realization of solid-state transfer switches (SSTS) that can seamlessly transfer between switches to provide high-quality uninterrupted power. Although a few legacy applications have been reported, SSTS could have an important role to play in alternating-current...

2010-12-31T23:59:59.000Z

413

Distribution Applications of the Asset and Risk Management (ARM) Workstation  

Science Conference Proceedings (OSTI)

Significant opportunities exist to improve maintenance, operation, and asset utilization of distribution systems and equipment. To improve the reactive (run-to-failure) maintenance practices typically employed today, a key hurdle to overcome is the lack of needed distribution system and equipment data. This report describes approaches that enable utilities to overcome this hurdle, reduce maintenance costs, and improve operations using current and planned distribution applications of the Asset and Risk Ma...

2004-12-13T23:59:59.000Z

414

Study on drywell cooler applicability to severe accident management  

SciTech Connect

This paper concerns applicability of drywell cooler (DWC) heat removal under severe accident condition in BWR plants. Newly developed heat removal models based on DWC heat removal experiments were built into the MAAP3 code. And then, two types of Japanese BWR were selected to evaluate DWC heat removal performance under typical severe accident scenarios. According to the results of the evaluation, DWC delays or prevents containment failure or venting. (authors)

Nakagawa, Takahiro [Information and manufacturing systems division, Toshiba Plant Systems and Services Corporation, 8, Shinsugita-cho, Isogo-ku, Yokohama, 235-8523 (Japan); Akinaga, Makoto [Power and Industrial Systems R and D Center, Toshiba Corporation, 4-1 Ukishima-cho, Kawasaki-ku, Kawasaki, 210-0862 (Japan); Hamazaki, Ryoichi [Isogo Nuclear Engineering Center, Toshiba Corporation, 8, Shinsugita-cho, Isogo-ku, Yokohama, 235-8523 (Japan); Matsuo, Toshihiro [Nuclear Power Engineering Department, Tokyo Electric Power Company, 1-3 Uchisaiwai-cho 1-chome, Chiyoda-ku, Tokyo 100-0011 (Japan); Hashimoto, Kouji [Nuclear Plant Engineering Department, HITACHI, Ltd., 1-1, Saiwai-cho, 3-chome, Hitachi-shi, Ibaraki-ken, 317-8511 (Japan)

2004-07-01T23:59:59.000Z

415

NEW GUN CAPABILITY WITH INTERCHANGABLE BARRELS TO INVESTIGATE LOW VELOCITY IMPACT REGIMES AT THE LAWRENCE LIVERMORE NATIONAL LABORATORY HIGH EXPLOSIVES APPLICATIONS FACILITY  

SciTech Connect

A new gas gun capability is being activated at Lawrence Livermore National Laboratories located in the High Explosives Applications Facility (HEAF). The single stage light gas (dry air, nitrogen, or helium) gun has interchangeable barrels ranging from 25.4 mm to 76.2 mm in diameter with 1.8 meters in length and is being fabricated by Physics Applications, Inc. Because it is being used for safety studies involving explosives, the gun is planned for operation inside a large enclosed firing tank, with typical velocities planned in the range of 10-300 m/s. Three applications planned for this gun include: low velocity impact of detonator or detonator/booster assemblies with various projectile shapes, the Steven Impact test that involves impact initiation of a cased explosive target, and the Taylor impact test using a cylindrical explosive sample impacted onto a rigid anvil for fracture studies of energetic materials. A highlight of the gun features, outline on work in progress for implementing this capability, and discussion of the planned areas of research will be included.

Vandersall, K S; Behn, A; Gresshoff, M; Jr., L F; Chiao, P I

2009-09-16T23:59:59.000Z

416

Reducing power consumption during execution of an application on a plurality of compute nodes  

DOE Patents (OSTI)

Methods, apparatus, and products are disclosed for reducing power consumption during execution of an application on a plurality of compute nodes that include: executing, by each compute node, an application, the application including power consumption directives corresponding to one or more portions of the application; identifying, by each compute node, the power consumption directives included within the application during execution of the portions of the application corresponding to those identified power consumption directives; and reducing power, by each compute node, to one or more components of that compute node according to the identified power consumption directives during execution of the portions of the application corresponding to those identified power consumption directives.

Archer, Charles J. (Rochester, MN); Blocksome, Michael A. (Rochester, MN); Peters, Amanda E. (Rochester, MN); Ratterman, Joseph D. (Rochester, MN); Smith, Brian E. (Rochester, MN)

2012-06-05T23:59:59.000Z

417

Assessment of the Potential for the Direct Application of Renewable Resources. Staff Issue Paper  

DOE Green Energy (OSTI)

This issue paper is intended to take a general look at the direct application of renewable resources. The focus of the paper is to provide background information on what is currently known about these resources. The Council is interested in comments to supplement the information discussed in this paper. Perhaps more importantly, the Council is looking for recommendations on how to treat these resources in the next power plan. The Council is faced with at least two important questions related to this issue. First, should the Council attempt to develop detailed supply curves for these resources? Second, should programs be developed to encourage the acquisition of these resources? The direct application of renewable resources is generally defined as the use of a renewable resource such as solar, hydro, wind, geothermal and biomass for the direct reduction of electrical energy use by a consumer. While there have been previous staff analysis of these resources they have not been explicitly treated in previous power plans. Given the renewed emphasis on evaluating the environmental consequences of resource development, these relatively benign resources merit further analysis. This paper will provide the basis for treatment of direct application of renewable resources in the 1990 Power Plan. Most of these resources tend to be site specific and typically require large collection areas to capture a significant amount of energy. Because of high fixed installation costs, they also tend to be most cost effective with higher usage. These characteristics generally prevent widespread regional application and limit the size of any particular resource. Early programs designed to encourage these resources focused on individual end use applications. However, given the unique characteristics of these resources, it is likely that future programs will treat these resources as one option among several conservation measures applied to a given end use or sector. Several of the direct application of renewable resources appear cost effective today or are close enough to justify further analysis. Examples include solar domestic water heating, passive solar heating east of the cascades, geothermal heating systems and daylighting in commercial buildings. This paper will examine these uses of direct application of renewable resources as well as others in detail and will provide recommendations for treatment in the 1990 Power Plan.

None

1989-10-16T23:59:59.000Z

418

Decision Applications: D, Decision Applications: LANL  

NLE Websites -- All DOE Office Websites (Extended Search)

Decision Applications Division Systems Engineering and Integration, D-3 Energy and Infrastructure Analysis, D-4 Nuclear Design and Risk Analysis, D-5 Risk Analysis and Decision...

419

Fuel Cell Systems for Portable, Backup, and UPS Applications  

NLE Websites -- All DOE Office Websites (Extended Search)

U.S. Federal Agency Purchasing Managers Federal Agency Purchasing Managers Fuel Cell Systems for Portable, Backup and UPS Fuel Cell Systems for Portable, Backup and UPS Applications Applications Eric Simpkins, USFCC President Eric Simpkins, USFCC President Vice President, IdaTech, LLC Vice President, IdaTech, LLC Washington, DC Washington, DC April 26, 2007 April 26, 2007 Definitions Introduction What's Available & How Used Typical Operation & Maintenance Time: Order to Site Installation Pricing Summary 1 i l Megawatts l backup, cogeneration, trigeneration Material handling et. al. Micro & Man-Portable * Less Than 100 Watts * Consumer electronics, defense (solder power), speciality appl cations Portable, Backup, APU * 100 Watts to 15 Kilowatts * Battery rep

420

Introduction to plunger lift: applications, advantages and limitations  

Science Conference Proceedings (OSTI)

This study discusses the principle of plunger lift and its possible applications. Typical applications are (1) removal of liquids from gas wells, (2) hi-ratio oil well production, (3) paraffin and hydrate control, and (4) increased efficiency of intermittent gas lift wells. Some advantages of this system are low initial cost, very little maintenance, and that there is no external source of energy required in most cases. Limitations such as mechanical conditions, gas and liquid volumes and depths also are discussed. There is a brief section concerning the various types of equipment available.

Beauregard, E.; Ferguson, P.L.

1981-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Expanded rock blast modeling capabilities of DMC{_}BLAST, including buffer blasting  

SciTech Connect

A discrete element computer program named DMC{_}BLAST (Distinct Motion Code) has been under development since 1987 for modeling rock blasting. This program employs explicit time integration and uses spherical or cylindrical elements that are represented as circles in 2-D. DMC{_}BLAST calculations compare favorably with data from actual bench blasts. The blast modeling capabilities of DMC{_}BLAST have been expanded to include independently dipping geologic layers, top surface, bottom surface and pit floor. The pit can also now be defined using coordinates based on the toe of the bench. A method for modeling decked explosives has been developed which allows accurate treatment of the inert materials (stemming) in the explosive column and approximate treatment of different explosives in the same blasthole. A DMC{_}BLAST user can specify decking through a specific geologic layer with either inert material or a different explosive. Another new feature of DMC{_}BLAST is specification of an uplift angle which is the angle between the normal to the blasthole and a vector defining the direction of explosive loading on particles adjacent to the blasthole. A buffer (choke) blast capability has been added for situations where previously blasted material is adjacent to the free face of the bench preventing any significant lateral motion during the blast.

Preece, D.S. [Sandia National Labs., Albuquerque, NM (United States); Tidman, J.P.; Chung, S.H. [ICI Explosives (Canada)

1996-12-31T23:59:59.000Z

422

Casting Apparatus Including A Gas Driven Molten Metal Injector And Method  

DOE Patents (OSTI)

The casting apparatus (50) includes a holding vessel (10) for containing a supply of molten metal (12) and a casting mold (52) located above the holding vessel (10) and having a casting cavity (54). A molten metal injector (14) extends into the holding vessel (10) and is at least partially immersed in the molten metal (12) in the holding vessel (10). The molten metal injector (14) is in fluid communication with the casting cavity (54). The molten metal injector (14) has an injector body (16) defining an inlet opening (24) for receiving molten metal into the injector body (16). A gas pressurization source (38) is in fluid communication with the injector body (16) for cyclically pressurizing the injector body (16) and inducing molten metal to flow from the injector body (16) to the casting cavity (54). An inlet valve (42) is located in the inlet opening (24) in the injector body (16) for filling molten metal into the injector body (16). The inlet valve (42) is configured to prevent outflow of molten metal from the injector body (16) during pressurization and permit inflow of molten metal into the injector body (16) after pressurization. The inlet valve (42) has an inlet valve actuator (44) located above the surface of the supply of molten metal (12) and is operatively connected to the inlet valve (42) for operating the inlet valve (42) between open and closed positions.

Meyer, Thomas N. (Murrysville, PA)

2004-06-01T23:59:59.000Z

423

Funding for state, city, and county governments in the state includes:  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

NE Nebraska Total Sum City, County, and SEO Allocations NE Nebraska Total Sum City, County, and SEO Allocations All $18,810,300 NE Nebraska State Energy Office $9,593,500 NE Bellevue City $194,200 NE Fremont City $106,400 NE Grand Island City $199,000 NE Hastings City $109,900 NE Kearney City $131,100 NE Lincoln City $2,401,000 NE Norfolk City $101,500 NE North Platte City $105,300 NE Omaha City $4,331,500 NE Papillion City $91,300 NE Cass County $99,900 NE Dakota County $87,300 NE Dawson County $106,300 NE Douglas County $255,800 NE Gage County $98,000 NE Lancaster County $110,300 NE Platte County $139,200 NE Sarpy County $312,600 NE Saunders County $80,600 NE Scotts Bluff County $155,600 In addition, today's announcement includes funding for the following Tribal

424

Funding for state, city, and county governments in the state includes:  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

NM New Mexico Total Sum City, County, and SEO NM New Mexico Total Sum City, County, and SEO Allocations All $20,608,300 NM New Mexico State Energy Office $9,593,500 NM Alamogordo City $147,700 NM Albuquerque City $5,051,200 NM Carlsbad City $107,800 NM Clovis City $139,800 NM Farmington City $191,800 NM Hobbs City $128,700 NM Las Cruces City $888,000 NM Rio Rancho City $697,000 NM Roswell City $195,500 NM Santa Fe City $781,600 NM Bernalillo County $459,500 NM Dona Ana County $446,900 NM Grant County $126,400 NM McKinley County $299,600 NM Rio Arriba County $166,500 NM San Juan County $329,400 NM Sandoval County $169,500 NM Santa Fe County $264,000 NM Taos County $134,100 NM Valencia County $289,800 In addition, today's announcement includes funding for the following Tribal

425

Funding for state, city, and county governments in the state includes:  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

NV NV Nevada Total Sum City, County, and SEO Allocations All $31,983,500 NV Nevada State Energy Office $9,593,500 NV Boulder City City $61,600 NV Carson City City $538,900 NV Elko City $76,500 NV Fernley City $52,000 NV Henderson City $2,237,000 NV Las Vegas City $5,449,200 NV Mesquite City $69,900 NV North Las Vegas City $1,907,400 NV Reno City $2,142,800 NV Sparks City $840,000 NV Churchill County $104,900 NV Clark County $7,663,500 NV Douglas County $195,000 NV Elko County $123,600 NV Humboldt County $75,600 NV Lyon County $165,200 NV Nye County $185,700 NV Pershing County $50,000 NV Washoe County $401,200 NV White Pine County $50,000 In addition, today's announcement includes funding for the following Tribal

426

Information management for global environmental change, including the Carbon Dioxide Information Analysis Center  

Science Conference Proceedings (OSTI)

The issue of global change is international in scope. A body of international organizations oversees the worldwide coordination of research and policy initiatives. In the US the National Science and Technology Council (NSTC) was established in November of 1993 to provide coordination of science, space, and technology policies throughout the federal government. NSTC is organized into nine proposed committees. The Committee on Environmental and Natural Resources (CERN) oversees the US Department of Energy`s Global Change Research Program (USGCRP). As part of the USGCRP, the US Department of Energy`s Global Change Research Program aims to improve the understanding of Earth systems and to strengthen the scientific basis for the evaluation of policy and government action in response to potential global environmental changes. This paper examines the information and data management roles of several international and national programs, including Oak Ridge National Laboratory`s (ORNL`s) global change information programs. An emphasis will be placed on the Carbon Dioxide Information Analysis Center (CDIAC), which also serves as the World Data Center-A for Atmospheric Trace Gases.

Stoss, F.W. [Oak Ridge National Lab., TN (United States). Carbon Dioxide Information Analysis Center

1994-06-01T23:59:59.000Z

427

Magnetohydrodynamic Simulations of the Formation of Cold Fronts in Clusters of Galaxies including Heat Conduction  

E-Print Network (OSTI)

Recent Chandra observations of clusters of galaxies revealed the existence of a sharp ridge in the X-ray surface brightness where the temperature drops across the front. This front is called the cold front. We present the results of two-dimensional magnetohydrodynamic simulations of the time evolution of a dense subcluster plasma moving in a cluster of galaxies. Anisotropic heat conduction along the magnetic field lines is included. In the models without magnetic fields, the numerical results indicate that the heat conduction from the hot ambient plasma heats the cold dense plasma of the subcluster and diffuses out the cold front. When magnetic fields exist in a cluster of galaxies, however, cold fronts can be maintained because the heat conduction across the magnetic field lines is suppressed. We found that, even when the magnetic fields in a cluster of galaxies are disordered, heat conduction across the front is restricted because the magnetic field lines are stretched along the front. Numerical results reproduced the X-ray intensity distribution observed in the A3667 cluster of galaxies.

Naoki Asai; Naoya Fukuda; Ryoji Matsumoto

2004-04-07T23:59:59.000Z

428

Solar energy collector including a weightless balloon with sun tracking means  

DOE Patents (OSTI)

A solar energy collector having a weightless balloon, the balloon including a transparent polyvinylfluoride hemisphere reinforced with a mesh of ropes secured to its outside surface, and a laminated reflector hemisphere, the inner layer being clear and aluminized on its outside surface and the outer layer being opaque, the balloon being inflated with lighter-than-air gas. A heat collection probe extends into the balloon along the focus of reflection of the reflective hemisphere for conducting coolant into and out of the balloon. The probe is mounted on apparatus for keeping the probe aligned with the sun's path, the apparatus being founded in the earth for withstanding wind pressure on the balloon. The balloon is lashed to the probe by ropes adhered to the outer surface of the balloon for withstanding wind pressures of 100 miles per hour. Preferably, the coolant is liquid sodium-potassium eutectic alloy which will not normally freeze at night in the temperate zones, and when heated to 4,000.degree. R exerts a pressure of only a few atmospheres.

Hall, Frederick F. (2452 Villaneuva Way, Mountain View, CA 94040)

1978-01-01T23:59:59.000Z

429

High accuracy power spectra including baryonic physics in dynamical Dark Energy models  

E-Print Network (OSTI)

The next generation mass probes will obtain information on non--linear power spectra P(k,z) and their evolution, allowing us to investigate the nature of Dark Energy. To exploit such data we need high precision simulations, extending at least up to scales of k\\simeq 10 h^-1 Mpc, where the effects of baryons can no longer be neglected. In this paper, we present a series of large scale hydrodynamical simulations for LCDM and dynamical Dark Energy (dDE) models, in which the equation of state parameter is z-dependent. The simulations include gas cooling, star formation and Supernovae feedback. They closely approximate the observed star formation rate and the observationally derived star/Dark Matter mass ratio in collapsed systems. Baryon dynamics cause spectral shifts exceeding 1% at k > 2-3 hMpc^-1 compared to pure n-body simulations in the LCDM simulations. This agrees with previous studies, although we find a smaller effect (~50%) on the power spectrum amplitude at higher k's. dDE exhibits similar behavior, ev...

Casarini, Luciano; Bonometto, Silvio A; Stinson, Greg S

2010-01-01T23:59:59.000Z

430

QCD Equation of State From a Chiral Hadronic Model Including Quark Degrees of Freedom  

E-Print Network (OSTI)

This work presents an effective model for strongly interacting matter and the QCD equation of state (EoS). The model includes both hadron and quark degrees of freedom and takes into account the transition of chiral symmetry restoration as well as the deconfinement phase transition. At low temperatures $T$ and baryonic densities $\\rho_B$ a hadron resonance gas is described using a SU(3)-flavor sigma-omega model and a quark phase is introduced in analogy to PNJL models for higher $T$ and $\\rho_B$. In this way, the correct asymptotic degrees of freedom are used in a wide range of $T$ and $\\rho_B$. Here, results of this model concerning the chiral and deconfinement phase transitions and thermodynamic model properties are presented. Large hadron resonance multiplicities in the transition region emphasize the importance of heavy-mass resonance states in this region and their impact on the chiral transition behavior. The resulting phase diagram of QCD matter at small chemical potentials is in line with latest lattice QCD and thermal model results.

Philip Rau; Jan Steinheimer; Stefan Schramm; Horst Stcker

2013-06-14T23:59:59.000Z

431

Estimating parameters of coalescing compact binaries with a detector network including LIGO Australia  

E-Print Network (OSTI)

One of the goals of gravitational-wave astronomy is simultaneous detection of gravitational-wave signals from merging compact-object binaries and the electromagnetic transients from these mergers. With the next generation of advanced ground-based gravitational wave detectors under construction, we examine the benefits of the proposed extension of the detector network to include a fourth site in Australia in addition to the network of Hanford, Livingston and Cascina sites. Using Bayesian parameter-estimation analyses of simulated gravitational-wave signals from a range of coalescing-binary locations and orientations, we study the improvement in parameter estimation. We find that an Australian detector can break degeneracies in several parameters; in particular, the localization of the source on the sky is improved by a factor of ~4, with more modest improvements in distance and binary inclination estimates. This enhanced ability to localize sources on the sky will be crucial in any search for electromagnetic counterparts to detected gravitational-wave signals.

Benjamin Aylott; Benjamin Farr; Vassiliki Kalogera; Ilya Mandel; Vivien Raymond; Carl Rodriguez; Marc van der Sluys; Alberto Vecchio; John Veitch

2011-06-13T23:59:59.000Z

432

Applying environmental externalities to US Clean Coal Technologies for Asia. [Including external environmental costs  

SciTech Connect

The United States is well positioned to play an expanding role in meeting the energy technology demands of the Asian Pacific Basin, including Indonesia, Thailand, and the Republic of China (ROC-Taiwan). The US Department of Energy Clean Coal Technology (CCT) Demonstration Program provides a proving ground for innovative coal-related technologies that can be applied domestically and abroad. These innovative US CCTs are expected to satisfy increasingly stringent environmental requirements while substantially improving power generation efficiencies. They should also provide distinct advantages over conventional pulverized coal-fired combustors. Finally, they are expected to be competitive with other energy options currently being considered in the region. This paper presents potential technology scenarios for Indonesia, Thailand, and the ROC-Taiwan and considers an environmental cost-benefit approach employing a newly developed method of applying environmental externalities. Results suggest that the economic benefits from increased emission control can indeed be quantified and used in cost-benefit comparisons, and that US CCTs can be very cost effective in reducing emissions.

Szpunar, C.B.; Gillette, J.L.

1993-01-01T23:59:59.000Z

433

RDI's Wisdom Way Solar Village Final Report: Includes Utility Bill Analysis of Occupied Homes  

DOE Green Energy (OSTI)

7. 2-4 bedrooms, 1,100-1,700 ft2. The design heating loads in the homes were so small that each home is heated with a single, sealed-combustion, natural gas room heater. The cost savings from the simple HVAC systems made possible the tremendous investments in the homes' envelopes. The Consortium for Advanced Residential Buildings (CARB) monitored temperatures and comfort in several homes during the winter of 2009-2010. In the Spring of 2011, CARB obtained utility bill information from 13 occupied homes. Because of efficient lights, appliances, and conscientious home occupants, the energy generated by the solar electric systems exceeded the electric energy used in most homes. Most homes, in fact, had a net credit from the electric utility over the course of a year. On the natural gas side, total gas costs averaged $377 per year (for heating, water heating, cooking, and clothes drying). Total energy costs were even less - $337 per year, including all utility fees. The highest annual energy bill for any home evaluated was $458; the lowest was $171.

Robb Aldrich, Steven Winter Associates

2011-07-01T23:59:59.000Z

434

SEARCHING FOR EXTRATERRESTRIAL INTELLIGENCE SIGNALS IN ASTRONOMICAL SPECTRA, INCLUDING EXISTING DATA  

Science Conference Proceedings (OSTI)

The main purpose of this article is to make astronomers aware that Searches for Extraterrestrial Intelligence (SETIs) can be carried out by analyzing standard astronomical spectra, including those they have already taken. Simplicity is the outstanding advantage of a search in spectra. The spectra can be analyzed by simple eye inspection or a few lines of code that uses Fourier transform software. Theory, confirmed by published experiments, shows that periodic signals in spectra can be easily generated by sending light pulses separated by constant time intervals. While part of this article, like all articles on SETIs, is highly speculative the basic physics is sound. In particular, technology now available on Earth could be used to send signals having the required energy to be detected at a target located 1000 lt-yr away. Extraterrestrial Intelligence (ETI) could use these signals to make us aware of their existence. For an ETI, the technique would also have the advantage that the signals could be detected both in spectra and searches for intensity pulses like those currently carried out on Earth.

Borra, Ermanno F., E-mail: borra@phy.ulaval.ca [Centre d'Optique, Photonique et Laser, Departement de Physique, Universite Laval, Quebec G1 K 7P4 (Canada)

2012-12-01T23:59:59.000Z

435

A Case for Including Atmospheric Thermodynamic Variables in Wind Turbine Fatigue Loading Parameter Identification  

DOE Green Energy (OSTI)

This paper makes the case for establishing efficient predictor variables for atmospheric thermodynamics that can be used to statistically correlate the fatigue accumulation seen on wind turbines. Recently, two approaches to this issue have been reported. One uses multiple linear-regression analysis to establish the relative causality between a number of predictors related to the turbulent inflow and turbine loads. The other approach, using many of the same predictors, applies the technique of principal component analysis. An examination of the ensemble of predictor variables revealed that they were all kinematic in nature; i.e., they were only related to the description of the velocity field. Boundary-layer turbulence dynamics depends upon a description of the thermal field and its interaction with the velocity distribution. We used a series of measurements taken within a multi-row wind farm to demonstrate the need to include atmospheric thermodynamic variables as well as velocity-related ones in the search for efficient turbulence loading predictors in various turbine-operating environments. Our results show that a combination of vertical stability and hub-height mean shearing stress variables meet this need over a period of 10 minutes.

Kelley, N. D.

1999-08-02T23:59:59.000Z

436

Funding for state, city, and county governments in the state includes:  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

MT MT Montana Total Sum City, County, and SEO Allocations All $13,971,000 MT Montana State Energy Office $9,593,500 MT Anaconda-Deer Lodge City $50,000 MT Billings City $1,003,000 MT Bozeman City $175,500 MT Butte-Silver Bow City $138,700 MT Great Falls City $570,100 MT Havre City $50,000 MT Helena City $138,600 MT Kalispell City $96,700 MT Miles City City $50,000 MT Missoula City $680,400 MT Cascade County $94,400 MT Flathead County $274,200 MT Gallatin County $198,700 MT Lake County $119,500 MT Lewis and Clark County $120,400 MT Lincoln County $80,000 MT Missoula County $151,000 MT Park County $67,100 MT Ravalli County $167,400 MT Yellowstone County $151,800 In addition, today's announcement includes funding for the following Tribal

437

Thermoelectric material including a multiple transition metal-doped type I clathrate crystal structure  

DOE Patents (OSTI)

A thermoelectric material includes a multiple transition metal-doped type I clathrate crystal structure having the formula A.sub.8TM.sub.y.sub.1.sup.1TM.sub.y.sub.2.sup.2 . . . TM.sub.y.sub.n.sup.nM.sub.zX.sub.46-y.sub.1.sub.-y.sub.2.sub.- . . . -y.sub.n.sub.-z. In the formula, A is selected from the group consisting of barium, strontium, and europium; X is selected from the group consisting of silicon, germanium, and tin; M is selected from the group consisting of aluminum, gallium, and indium; TM.sup.1, TM.sup.2, and TM.sup.n are independently selected from the group consisting of 3d, 4d, and 5d transition metals; and y.sub.1, y.sub.2, y.sub.n and Z are actual compositions of TM.sup.1, TM.sup.2, TM.sup.n, and M, respectively. The actual compositions are based upon nominal compositions derived from the following equation: z=8q.sub.A-|.DELTA.q.sub.1|y.sub.1-|.DELTA.q.sub.2|y.sub.2- . . . -|.DELTA.q.sub.n|y.sub.n, wherein q.sub.A is a charge state of A, and wherein .DELTA.q.sub.1, .DELTA.q.sub.2, .DELTA.q.sub.n are, respectively, the nominal charge state of the first, second, and n-th TM.

Yang, Jihui (Lakeshore, CA); Shi, Xun (Troy, MI); Bai, Shengqiang (Shanghai, CN); Zhang, Wenqing (Shanghai, CN); Chen, Lidong (Shanghai, CN); Yang, Jiong (Shanghai, CN)

2012-01-17T23:59:59.000Z

438

Control System Applicable Use Assessment of the Secure Computing Corporation - Secure Firewall (Sidewinder)  

Science Conference Proceedings (OSTI)

Battelles National Security & Defense objective is, applying unmatched expertise and unique facilities to deliver homeland security solutions. From detection and protection against weapons of mass destruction to emergency preparedness/response and protection of critical infrastructure, we are working with industry and government to integrate policy, operational, technological, and logistical parameters that will secure a safe future. In an ongoing effort to meet this mission, engagements with industry that are intended to improve operational and technical attributes of commercial solutions that are related to national security initiatives are necessary. This necessity will ensure that capabilities for protecting critical infrastructure assets are considered by commercial entities in their development, design, and deployment lifecycles thus addressing the alignment of identified deficiencies and improvements needed to support national cyber security initiatives. The Secure Firewall (Sidewinder) appliance by Secure Computing was assessed for applicable use in critical infrastructure control system environments, such as electric power, nuclear and other facilities containing critical systems that require augmented protection from cyber threat. The testing was performed in the Pacific Northwest National Laboratorys (PNNL) Electric Infrastructure Operations Center (EIOC). The Secure Firewall was tested in a network configuration that emulates a typical control center network and then evaluated. A number of observations and recommendations are included in this report relating to features currently included in the Secure Firewall that support critical infrastructure security needs.

Hadley, Mark D.; Clements, Samuel L.

2009-01-01T23:59:59.000Z

439

Typical Generator for Proximity Fuse - Exhibits: Jacob ...  

Science Conference Proceedings (OSTI)

... 1942. Rabinow designed the proximity fuse's power supply. He used a small windmill at the nose of the fuse to drive a small generator. ...

2005-09-06T23:59:59.000Z

440

Block IV solar cell module design and test specification for Intermediate Load Center applications  

DOE Green Energy (OSTI)

Requirements are established for performance of terrestial solar cell modules intended for use in various test applications typically characterized as Intermediate Load Centers. During the 1979 to 1980 time period, such applications are expected to be in the 20 kilowatt to 500 kilowatt size range. In addition to module design and performance requirements, a series of characterization and qualification tests necessary to certify the module design for production, and the necessary performance tests for acceptance of modules are also specified.

Not Available

1978-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Biological Applications Illustrating Linear  

E-Print Network (OSTI)

and is a subtractive mode (pigments absorb light rather) starting with white paper. Black ink (K) is also required. #12 different colors? Would it help if we added more colors? Could we do with fewer colors? Why do we typically and intensities of those colors created by light on a white screen. Vector: A spotlight that creates exactly

Walton, Brian

442

ADVANCED POWER SYSTEMS - ASH BEHAVIOR IN POWER SYSTEMS. INCLUDES THE SEMIANNUAL REPORT FOR THE PERIOD JANUARY 01, 1998 - JUNE 30, 1998.  

SciTech Connect

The overall goal of this initiative is to develop fundamental knowledge of ash behavior in power systems for the purpose of increasing power production efficiency, reducing operation and maintenance costs, and reducing greenhouse gas emissions into the atmosphere. The specific objectives of this initiative focus primarily on ash behavior related to advanced power systems and include the following: Determine the current status of the fundamental ash interactions and deposition formation mechanisms as already reported through previous or ongoing projects at the EERC or in the literature; Determine sintering mechanisms for temperatures and particle compositions that are less well known and remain for the most part undetermined; Identify the relationship between the temperature of critical viscosity (T{sub cv}) as measured in a viscometer and the crystallization occurring in the melt; Perform a literature search on the use of heated-stage microscopy (HSM) for examining in situ ash-sintering phenomena and then validate the use of HSM in the determination of viscosity in spherical ash particles; Ascertain the formation and stability of specific mineral or amorphous phases in deposits typical of advanced power systems; and Evaluate corrosion for alloys being used in supercritical combustion systems.

1998-09-01T23:59:59.000Z

443

A simple model of impact dynamics in many dimensional systems, with applications to heat exchangers  

E-Print Network (OSTI)

A simple model of impact dynamics in many dimensional systems, with applications to heat exchangers present a simple hybrid model of impact dynamics in heat exchangers. The method, based on graph theory and experimental evidence. 1 Introduction A heat exchanger typically consists of a large number of thin pipes

Bristol, University of

444

Reconstruction of hillslope and valley paleotopography by application of a geomorphic model  

Science Conference Proceedings (OSTI)

Many applications in geology require estimation of the depth and thickness of lithologic layers based on limited observations. The boundaries of such layers are typically estimated using Kriging or other estimation methods that produce smooth surfaces. ... Keywords: Draining, Fractal, Groundwater, Interpolation, Paleotopography, Spline

Michael L. Coleman; Jeffrey D. Niemann; Elaine P. Jacobs

2009-09-01T23:59:59.000Z

445

Fair scheduling of bag-of-tasks applications using distributed Lagrangian optimization  

Science Conference Proceedings (OSTI)

Large scale distributed systems typically comprise hundreds to millions of entities (applications, users, companies, universities) that have only a partial view of resources (computers, communication links). How to fairly and efficiently share such resources ... Keywords: Distributed scheduling, Grid computing, Lagrangian optimization, Steady-state scheduling

Rmi Bertin, Sascha Hunold, Arnaud Legrand, Corinne Touati

2014-01-01T23:59:59.000Z

446

Design of Individuation PDC Bit and its Application in Santanghu Basin Vocanics  

Science Conference Proceedings (OSTI)

Niudong and Malang area in Santanghu Basin is a typical reservoir of volcanics, there are basalt layers with the thickness from hundreds to thousands meters under Permian, so the drill ability of which was bad, choice of bit was limited, and the drilling ... Keywords: Drillability, Individuation PDC Bit, Optimization Design, Test Application

Wei Zhongliang; Guo Lichun

2011-01-01T23:59:59.000Z

447

Hardware acceleration of JPEG2000 image compression for low-power embedded applications  

Science Conference Proceedings (OSTI)

JPEG2000 is ideal as the next-generation still image compression standard, and it is expected to replace JPEG for embedded applications such as digital cameras. These typically require low-power operation, so by combining a low-power microprocessor with ... Keywords: EBCOT, JPEG2000, SoC, SoPC, embedded systems, image compression

Darren Freeman; Greg Knowles

2003-02-01T23:59:59.000Z

448

NDU Application for 2013  

Energy.gov (U.S. Department of Energy (DOE))

The 2013 NDU Application is an application package that must be completed to attend the National Security Studies Program. This program is designed to prepare future leaders of civilian agencies...

449

Application: Cold Climate  

Science Conference Proceedings (OSTI)

*. Bookmark and Share. Application: Cold Climate. Fire Suppression in Cold Climates: A Technical Review.. Catchpole, DV; 2000. ...

2011-12-22T23:59:59.000Z

450

Properties and Applications  

Science Conference Proceedings (OSTI)

...Powder Metallurgy Refractory Metals, Powder Metal Technologies and Applications, Vol 7, ASM Handbook, ASM International, 1998, p 903??913...

451

License Renewal Application PREFACE  

E-Print Network (OSTI)

The following describes the information location, layout, and editorial conventions in the Beaver Valley Power Station (BVPS) License Renewal Application (hereinafter referred to as this application or the application). Abbreviated names and acronyms used throughout the application are defined at the end of this preface. Commonly understood terms (such as U.S.) and terms used only in referenced document numbers may not be identified in this table. Regulatory documents such as NUREG-1801, Generic Aging Lessons Learned (GALL) Report,

Beaver Valley; Power Station

2007-01-01T23:59:59.000Z

452

Products and Applications  

Science Conference Proceedings (OSTI)

...lead consumed in the United States is used for battery applications. A lead-acid battery consists of a

453

Small Wind Turbine Testing and Applications Development  

Science Conference Proceedings (OSTI)

Small wind turbines offer a promising alternative for many remote electrical uses where there is a good wind resource. The National Wind Technology Center (NWTC) of the National Renewable Energy Laboratory helps further the role that small turbines can play in supplying remote power needs. The NWTC tests and develops new applications for small turbines. The NWTC also develops components used in conjunction with wind turbines for various applications. This paper describes wind energy research at the NWTC for applications including battery charging stations, water desalination/purification, and health clinics. Development of data acquisition systems and tests on small turbines are also described.

Corbus, D.; Baring-Gould, I.; Drouilhet, S.; Gevorgian, V.; Jimenez, T.; Newcomb, C.; Flowers, L.

1999-09-14T23:59:59.000Z

454

The CUNY Energy Institute Electrical Energy Storage Development for Grid Applications  

Science Conference Proceedings (OSTI)

1. Project Objectives The objectives of the project are to elucidate science issues intrinsic to high energy density electricity storage (battery) systems for smart-grid applications, research improvements in such systems to enable scale-up to grid-scale and demonstrate a large 200 kWh battery to facilitate transfer of the technology to industry. 2. Background Complex and difficult to control interfacial phenomena are intrinsic to high energy density electrical energy storage systems, since they are typically operated far from equilibrium. One example of such phenomena is the formation of dendrites. Such dendrites occur on battery electrodes as they cycle, and can lead to internal short circuits, reducing cycle life. An improved understanding of the formation of dendrites and their control can improve the cycle life and safety of many energy storage systems, including rechargeable lithium and zinc batteries. Another area where improved understanding is desirable is the application of ionic liquids as electrolytes in energy storage systems. An ionic liquid is typically thought of as a material that is fully ionized (consisting only of anions and cations) and is fluid at or near room temperature. Some features of ionic liquids include a generally high thermal stability (up to 450 C), a high electrochemical window (up to 6 V) and relatively high intrinsic conductivities. Such features make them attractive as battery or capacitor electrolytes, and may enable batteries which are safer (due to the good thermal stability) and of much higher energy density (due to the higher voltage electrode materials which may be employed) than state of the art secondary (rechargeable) batteries. Of particular interest is the use of such liquids as electrolytes in metal air batteries, where energy densities on the order of 1-2,000 Wh / kg are possible; this is 5-10 times that of existing state of the art lithium battery technology. The Energy Institute has been engaged in the development of flow-assisted nickel zinc battery technology. This technology has the promise of enabling low-cost (batteries have only demonstrated about 400 cycles to failure.

Banerjee, Sanjoy

2013-03-31T23:59:59.000Z

455

The CUNY Energy Institute Electrical Energy Storage Development for Grid Applications  

SciTech Connect

1. Project Objectives The objectives of the project are to elucidate science issues intrinsic to high energy density electricity storage (battery) systems for smart-grid applications, research improvements in such systems to enable scale-up to grid-scale and demonstrate a large 200 kWh battery to facilitate transfer of the technology to industry. 2. Background Complex and difficult to control interfacial phenomena are intrinsic to high energy density electrical energy storage systems, since they are typically operated far from equilibrium. One example of such phenomena is the formation of dendrites. Such dendrites occur on battery electrodes as they cycle, and can lead to internal short circuits, reducing cycle life. An improved understanding of the formation of dendrites and their control can improve the cycle life and safety of many energy storage systems, including rechargeable lithium and zinc batteries. Another area where improved understanding is desirable is the application of ionic liquids as electrolytes in energy storage systems. An ionic liquid is typically thought of as a material that is fully ionized (consisting only of anions and cations) and is fluid at or near room temperature. Some features of ionic liquids include a generally high thermal stability (up to 450 C), a high electrochemical window (up to 6 V) and relatively high intrinsic conductivities. Such features make them attractive as battery or capacitor electrolytes, and may enable batteries which are safer (due to the good thermal stability) and of much higher energy density (due to the higher voltage electrode materials which may be employed) than state of the art secondary (rechargeable) batteries. Of particular interest is the use of such liquids as electrolytes in metal air batteries, where energy densities on the order of 1-2,000 Wh / kg are possible; this is 5-10 times that of existing state of the art lithium battery technology. The Energy Institute has been engaged in the development of flow-assisted nickel zinc battery technology. This technology has the promise of enabling low-cost (<$250 / kWh) energy storage, while overcoming the historical poor cycle-life drawback. To date, the results have been promising, with a cycle life of 1,500 cycles demonstrated in small laboratory cells an improvement of approximately 400%. Prior state of the art nickel zinc batteries have only demonstrated about 400 cycles to failure.

Banerjee, Sanjoy

2013-03-31T23:59:59.000Z

456

Bulk Formulation of the Heat and Water Vapor Fluxes at the AirSea Interface, Including Nonmolecular Contributions  

Science Conference Proceedings (OSTI)

Accurate prediction of the airsea sensible and latent heat fluxes is vital for nearly all applications of atmosphere and ocean models. Existing theories of heat transfer over rough surfaces provide a starting point, but they seem incomplete ...

James A. Mueller; Fabrice Veron

2010-01-01T23:59:59.000Z

457

Some new applications of supercapacitors in power electronic systems  

E-Print Network (OSTI)

This thesis explores some new applications in power electronics for supercapacitors. This involves the design and development of dc-dc converters to interface the supercapacitor banks with the rest of the power electronic system. Two applications for supercapacitors are proposed and analyzed. The first application is aimed at high power applications such as motor drives. The proposed approach compensates the effect of voltage sags in the dc link of typical adjustable speed drives, thus reducing speed fluctuations in the motor and eliminating the possibility of nuisance tripping on the drive control board. The second approach presented in this thesis explores the use of supercapacitors to extend run-time for mobile devices such as laptop computers and hand held devices. Three possible approaches are explored: a) Supercapacitors connected directly across the battery; b) Battery-inductor-supercapacitor connection; and c) Supercapacitor, and battery connected via a DC-DC converter. Analytical models, simulation and experimental results on a typical laptop computer are presented.

Palma Fanjul, Leonardo Manuel

2003-08-01T23:59:59.000Z

458

LENS repair and modification of metal NW components:materials and applications guide.  

DOE Green Energy (OSTI)

Laser Engineered Net Shaping{trademark} (LENS{reg_sign}) is a unique, layer additive, metal manufacturing technique that offers the ability to create fully dense metal features and components directly from a computer solid model. LENS offers opportunities to repair and modify components by adding features to existing geometry, refilling holes, repairing weld lips, and many other potential applications. The material deposited has good mechanical properties with strengths typically slightly higher that wrought material due to grain refinement from a quickly cooling weld pool. The result is a material with properties similar to cold worked material, but without the loss in ductility traditionally seen with such treatments. Furthermore, 304L LENS material exhibits good corrosion resistance and hydrogen compatibility. This report gives a background of the LENS process including materials analysis addressing the requirements of a number of different applications. Suggestions are given to aid both the product engineer and the process engineer in the successful utilization of LENS for their applications. The results of testing on interface strength, machinability, weldability, corrosion resistance, geometric effects, heat treatment, and repair strategy testing are all included. Finally, the qualification of the LENS process is briefly discussed to give the user confidence in selecting LENS as the process of choice for high rigor applications. The testing showed LENS components to have capability in repair/modification applications requiring complex castings (W80-3 D-Bottle bracket), thin wall parts requiring metal to be rebuilt onto the part (W87 Firing Set Housing and Y-12 Test Rings), the filling of counterbores for use in reservoir reclamation welding (SRNL hydrogen compatibility study) and the repair of surface defects on pressure vessels (SRNL gas bottle repair). The material is machinable, as testing has shown that LENS deposited material machines similar to that of welded metal. Tool wear is slightly higher in LENS material than in wrought material, but not so much that one would be concerned with increased tooling cost. The LENS process achieved process qualification for the AY1E0125 D-Bottle Bracket from the W80-3 LEP program, and in the effort, also underwent testing in weapons environments. These tests included structural dynamic response testing and drop testing. The LENS deposited parts were compared in these tests with conventionally machined parts and showed equivalency to such an extent that the parts were accepted for use in parallel path subsystem-level weapon environment testing. The evaluation of LENS has shown that the process can be a viable option when either complete metal parts are needed or existing metal parts require modification or repair. The LENS Qualification Technology Investment team successfully investigated new applications for the LENS process and showed that it has great applicability across the Nuclear Weapons Complex as well as in other high rigor applications.

Smugeresky, John E. (Sandia National Laboratories, Livermore, CA); Gill, David Dennis; Oberhaus, Jason (BWXT Y-12); Adams, Thad (Savannah River National Laboratory); VanCamp, Chad (Kansas City Plant)

2006-11-01T23:59:59.000Z

459

User's Manual for the FEHM Application-A Finite-Element Heat- and Mass-Transfer Code  

DOE Green Energy (OSTI)

This document is a manual for the use of the FEHM application, a finite-element heat- and mass-transfer computer code that can simulate nonisothermal multiphase multicomponent flow in porous media. The use of this code is applicable to natural-state studies of geothermal systems and groundwater flow. A primary use of the FEHM application will be to assist in the understanding of flow fields and mass transport in the saturated and unsaturated zones below the proposed Yucca Mountain nuclear waste repository in Nevada. The equations of heat and mass transfer for multiphase flow in porous and permeable media are solved in the FEHM application by using the finite-element method. The permeability and porosity of the medium are allowed to depend on pressure and temperature. The code also has provisions for movable air and water phases and noncoupled tracers; that is, tracer solutions that do not affect the heat- and mass-transfer solutions. The tracers can be passive or reactive. The code can simulate two-dimensional, two-dimensional radial, or three-dimensional geometries. In fact, FEHM is capable of describing flow that is dominated in many areas by fracture and fault flow, including the inherently three-dimensional flow that results from permeation to and from faults and fractures. The code can handle coupled heat and mass-transfer effects, such as boiling, dryout, and condensation that can occur in the near-field region surrounding the potential repository and the natural convection that occurs through Yucca Mountain due to seasonal temperature changes. The code is also capable of incorporating the various adsorption mechanisms, ranging from simple linear relations to nonlinear isotherms, needed to describe the very complex transport processes at Yucca Mountain. This report outlines the uses and capabilities of the FEHM application, initialization of code variables, restart procedures, and error processing. The report describes all the data files, the input data, including individual input records or parameters, and the various output files. The system interface is described, including the software environment and installation instructions. Examples illustrating various aspects of the code are sprinkled throughout the report, and the final section demonstrates how to construct an input file, shows typical code execution, and gives three examples: heat conduction in a square, a reactive-transport problem, and Problem 5, Case of the DOE Code Comparison Project.

George A. Zyvoloski; Bruce A. Robinson; Zora V. Dash; Lynn L. Trease

1997-07-07T23:59:59.000Z

460

Wisconsin #include gcc  

E-Print Network (OSTI)

_time.tv_sec = current_time.tv_sec + 2; /* convert from micro to nano */ timeout_time.tv_nsec = current_time.tv_usec

Liblit, Ben

Note: This page contains sample records for the topic "typical applications include" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Laser Applications in Metal Surface Hardening  

E-Print Network (OSTI)

The acceptance of C02 lasers in industry to provide surface hardening is an established fact. Applications number in the hundreds in such diverse fields as automotive, office machines, air compressors, jet engines, military, paper converting, personal products, printing, plastics, forestry, mining, drilling, etc. Many specific examples are discussed with emphasis on why lasers were chosen and what significant economies in power consumption were realized. In one well-documented case, power consumption is shown to have dropped to 0.29% of the level for the previously used hardening process. The wear and fatigue characteristics of laser-hardened surfaces are reviewed. Reference is made to the operating principles of medium to high-power carbon-dioxide lasers. Typical examples are given of other laser processes such as welding, cutting, vaporizing, drilling, scribing, machining, etc.

Eckersley, J. S.

1982-01-01T23:59:59.000Z

462

Relaying and Controls for Generator Applications  

E-Print Network (OSTI)

In today's competitive marketplace, many electrical energy consumers are encouraged to enter into interruptible or cogeneration contracts by their electrical utility. Interruptible contracts provide year-round cost savings for the consumer, and defer costly infrastructure expansion for the utility. In some cases, existing generators and controls can be upgraded or modified for paralleling with the utility. In new installations, there are literally dozens of options available for generator operation. This paper provides an overview of generators, relaying and controls. Typical operational procedures are discussed to provide a framework for optimizing generator performance. Additionally, methods of providing electrical protection and control for generators are discussed for small and large generator applications at low and medium voltages. Note: The views expressed in this paper do not necessarily represent the views of the United States of America, the U. S. Department of Justice, or the Federal Bureau of Prisons.

Massey, G. W.

2000-04-01T23:59:59.000Z

463

Quantum technology and its applications  

Science Conference Proceedings (OSTI)

Quantum states of matter can be exploited as high performance sensors for measuring time, gravity, rotation, and electromagnetic fields, and quantum states of light provide powerful new tools for imaging and communication. Much attention is being paid to the ultimate limits of this quantum technology. For example, it has already been shown that exotic quantum states can be used to measure or image with higher precision or higher resolution or lower radiated power than any conventional technologies, and proof-of-principle experiments demonstrating measurement precision below the standard quantum limit (shot noise) are just starting to appear. However, quantum technologies have another powerful advantage beyond pure sensing performance that may turn out to be more important in practical applications: the potential for building devices with lower size/weight/power (SWaP) and cost requirements than existing instruments. The organizers of Quantum Technology Applications Workshop (QTAW) have several goals: (1) Bring together sponsors, researchers, engineers and end users to help build a stronger quantum technology community; (2) Identify how quantum systems might improve the performance of practical devices in the near- to mid-term; and (3) Identify applications for which more long term investment is necessary to realize improved performance for realistic applications. To realize these goals, the QTAW II workshop included fifty scientists, engineers, managers and sponsors from academia, national laboratories, government and the private-sector. The agenda included twelve presentations, a panel discussion, several breaks for informal exchanges, and a written survey of participants. Topics included photon sources, optics and detectors, squeezed light, matter waves, atomic clocks and atom magnetometry. Corresponding applications included communication, imaging, optical interferometry, navigation, gravimetry, geodesy, biomagnetism, and explosives detection. Participants considered the physics and engineering of quantum and conventional technologies, and how quantum techniques could (or could not) overcome limitations of conventional systems. They identified several auxiliary technologies that needed to be further developed in order to make quantum technology more accessible. Much of the discussion also focused on specific applications of quantum technology and how to push the technology into broader communities, which would in turn identify new uses of the technology. Since our main interest is practical improvement of devices and techniques, we take a liberal definition of 'quantum technology': a system that utilizes preparation and measurement of a well-defined coherent quantum state. This nomenclature encompasses features broader than entanglement, squeezing or quantum correlations, which are often more difficult to utilize outside of a laboratory environment. Still, some applications discussed in the workshop do take advantage of these 'quantum-enhanced' features. They build on the more established quantum technologies that are amenable to manipulation at the quantum level, such as atom magnetometers and atomic clocks. Understanding and developing those technologies through traditional engineering will clarify where quantum-enhanced features can be used most effectively, in addition to providing end users with improved devices in the near-term.

Boshier, Malcolm [Los Alamos National Laboratory; Berkeland, Dana [USG; Govindan, Tr [ARO; Abo - Shaeer, Jamil [DARPA

2010-12-10T23:59:59.000Z

464

TMS 2011: Exhibitor Details  

Science Conference Proceedings (OSTI)

Typical applications include Aluminium smelting, Refineries (esp. HF Alkylation), Petrochemical and Chemical Plants, Gas Production and Processing, Green...

465

Modeling, Simulation, Ceramics, and Chemical Processing  

Science Conference Proceedings (OSTI)

Mar 3, 2011 ... Typical applications include aerospace, robotic manipulators, motion simulators, injection molding, CNC machines and material testing...

466

Technical applications of aerogels  

SciTech Connect

Aerogel materials posses such a wide variety of exceptional properties that a striking number of applications have developed for them. Many of the commercial applications of aerogels such as catalysts, thermal insulation, windows, and particle detectors are still under development and new application as have been publicized since the ISA4 Conference in 1994: e.g.; supercapacitors, insulation for heat storage in automobiles, electrodes for capacitive deionization, etc. More applications are evolving as the scientific and engineering community becomes familiar with the unusual and exceptional physical properties of aerogels, there are also scientific and technical application, as well. This paper discusses a variety of applications under development at Lawrence Livermore National Laboratory for which several types of aerogels are formed in custom sizes and shapes. Particular discussions will focus on the uses of aerogels for physics experiments which rely on the exceptional, sometimes unique, properties of aerogels.

Hrubesh, L.W.

1997-08-18T23:59:59.000Z

467

NIST Laser Applications Staff Directory  

Science Conference Proceedings (OSTI)

Laser Applications Staff Directory. Staff. Name, Position, Office Phone. ... Contact. Laser Applications Group Keith Lykke, Group Leader. ...

2012-11-26T23:59:59.000Z

468

Laser Application for Material Processing  

Science Conference Proceedings (OSTI)

Oct 10, 2012 ... Advanced Materials, Processes and Applications for Additive Manufacturing: Laser Application for Material Processing Program Organizers:...

469

Amended Application for Presidential Permit OE Docket No: PP-371 Northern  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

LLC LLC Amended Application for Presidential Permit OE Docket No: PP-371 Northern Pass Transmission LLC Northern Pass Transmission LLC (Northern Pass) has submitted an amended application for a Presidential permit to construct, operate, maintain, and connect an electric transmission line across the United States border with Canada. Amended Application of Northern Pass Transmission LLC for Presidential Permit Exhibit 1 - Opinion of Counsel Exhibit 2 - General Area Map of Proposed Route Exhibit 3 - Diagrams of Cross-Section of Underground Cables Exhibit 4 - Drawings of Typical Structure Configurations Exhibit 5 - Chart of Proposed Structure Heights Exhibit 6 - Drawing of Typical Converter Terminal Exhibit 7 - General Area Map of North Section Exhibit 8 - General Area Map of Central Section

470

New Combined FAC Application  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Washington, DC 20585 MEMORANDUM FOR SITE ACQUISITION CAREER MANAGER FROM: SUBJECT: Application for In accordance with DOE Order 361.1B, paragraph 4.B, I hereby request the subject certification, for which I completed the applicable education, experience and training standards as documented below. 1. E-mail address: Duty station: 2. Previous certification (attached): Date last issued or renewed: 3. Education (FAC-C applications only): Bachelor's degree OR 24 semester hours among these disciplines: accounting, law, business,

471

CIM Application Integration  

Science Conference Proceedings (OSTI)

The EPRI Common Information Model (CIM) has been used as the basis or schema for implementing a real-time relational database in the CIM Application Integration Project. The CIM relational database is implemented in a normalized form so that it can support a complete range of utility transmission, generation, distribution, substation, and asset management applications. The objective of this document is to provide a final report on the CIM Application Integration Project.

2004-02-02T23:59:59.000Z

472

Program Review - Geothermal Exploration and Assessment Technology Program; Including a Report of the Reservoir Engineering Technical Advisory Group  

DOE Green Energy (OSTI)

In 1978, The Division of Geothermal Energy of the Department of Energy established the Geothermal Exploration and Assessment Technology Program. The purpose of this program is to ''provide assistance to the Nation's industrial community by helping to remove technical and associated economic barriers which presently inhibit efforts to bring geothermal electric power production and direct heat application on line''. In the near term this involves the adaptation of exploration and assessment techniques from the mineral and petroleum industry to geothermal applications. In the near to far term it involves the development of new technology which will improve the cost effectiveness of geothermal exploration.

Nielson, Dennis L., ed.

1979-12-01T23:59:59.000Z

473

Electrochemical Approaches to PV Busbar Application  

DOE Green Energy (OSTI)

Busbars are an integral component of any thin-film photovoltaic module and must be easy and quick to apply by PV manufacturers, as well as provide long-term reliability in deployed modules. Potential reliability issues include loss of adhesion and delamination, chemical instability under current collection conditions (electromigration or corrosion), compatibility of material and application method with subsequent encapsulation steps. Several new and novel busbar materials and application methods have been explored, including adhering metal busbars with various one- and two-part conductive epoxies or conductive adhesive films, ultrasonic bonding of metal busbar strips, and bonding of busbar strips using low-temperature solders. The most promising approach to date has been the direct application of metal busbars via various electrochemical techniques, which offers a variety of distinct advantages.

Pankow, J. W.

2005-01-01T23:59:59.000Z

474

License Application Guidelines  

market, and describe how the funding will be obtained. LICENSE APPLICATION GUIDELINES 6. ... Key events that have led to your companys current position in the

475

Welding Technologies and Applications  

Science Conference Proceedings (OSTI)

Oct 20, 2011 ... Joining of Advanced and Specialty Materials (JASM XIII): Welding Technologies and Applications Sponsored by: MS&T Organization Program...

476

Design Competition Application (PDF)  

Science Conference Proceedings (OSTI)

economics of the product in terms of costs and potential revenue ... Deadline: Applications and project reports must be received by TMS before December 15.

477

Chemistry Applications at NERSC  

NLE Websites -- All DOE Office Websites (Extended Search)

Chemistry Chemistry Applications Gaussian 09 Gaussian 09 is a connected series of programs for performing semi-empirical, density functional theory and ab initio molecular orbital...

478

Computer Applications & Process Control  

Science Conference Proceedings (OSTI)

[valSummaryfrmSearchResults]. Item 1. Topic: Computer Applications & Process Control. Sort by: Title, Author, Publisher, Product Type, In Stock, Date Published...

479

Applications of Sputtered Films  

Science Conference Proceedings (OSTI)

...circuits Thin-film lasers Memory devices High-temperature superconductors A variety of sputtering techniques can be used in most applications,

480

Medium energy nuclear data for applications  

SciTech Connect

The types of medium energy nuclear data required for applications are discussed. Features of analysis tools, consisting of both detailed nuclear model codes and simple formulas based on nuclear systematics are presented. The activities of the Medium Energy Nuclear Data Working Group (MENDWG) are described including the recent benchmark comparison of nuclear model codes. 40 refs., 7 figs.

Pearlstein, S.

1988-01-01T23:59:59.000Z