National Library of Energy BETA

Sample records for trade mark manufacturer

  1. Measurement of high energy x-ray beam penumbra with Gafchromic trade mark sign EBT radiochromic film

    SciTech Connect (OSTI)

    Cheung Tsang; Butson, Martin J.; Yu, Peter K. N.

    2006-08-15

    High energy x-ray beam penumbra are measured using Gafchromic trade mark sign EBT film. Gafchromic trade mark sign EBT, due to its limited energy dependence and high spatial resolution provide a high level of accuracy for dose assessment in penumbral regions. The spatial resolution of film detector systems is normally limited by the scanning resolution of the densitometer. Penumbral widths (80%/20%) measured at D{sub max} were found to be 2.8, 3.0, 3.2, and 3.4 mm ({+-}0.2 mm) using 5, 10, 20, and 30 cm square field sizes, respectively, for a 6 MV linear accelerator produced x-ray beam. This is compared to 3.2 mm{+-}0.2 mm (Kodak EDR2) and 3.6 mm{+-}0.2 mm (Kodak X-Omat V) at 10 cmx10 cm measured using radiographic film. Using a zero volume extrapolation technique for ionization chamber measurements, the 10 cmx10 cm field penumbra at D{sub max} was measured to be 3.1 mm, a close match to Gafchromic trade mark sign EBT results. Penumbral measurements can also be made at other depths, including the surface, as the film does not suffer significantly from dosimetric variations caused by changing x-ray energy spectra. Gafchromic trade mark sign EBT film provides an adequate measure of penumbral dose for high energy x-ray beams.

  2. Feasibility study for integrated solar cell manufacture in Russia. Export trade information

    SciTech Connect (OSTI)

    1998-07-01

    This report, conducted by Global Photovoltaic Specialists, Inc., was funded by the US Trade and Development Agency. The study concerns the techno-economic feasibility of fully integrated photovoltaic manufacture in Russia. In addition to the executive summary, the study consists of the following: (1) background of the project; (2) world market study; (3) technology prospects; (4) techno-economic feasibility-proprietary deleted; (5) financial-proprietary deleted; (6) conclusions and recommendations; (7) references; (8) bibliography.

  3. A Preclinical Study of the Safety and Efficacy of Occlusin Trade-Mark-Sign 500 Artificial Embolization Device in Sheep

    SciTech Connect (OSTI)

    Owen, Richard J.; Nation, Patrick N.; Polakowski, Robert; Biliske, Jennifer A.; Tiege, Paul B.

    2012-06-15

    Introduction: This study evaluated the safety, effectiveness, and biodegradation of a new embolic agent, Occlusin Trade-Mark-Sign 503 Artificial Embolization Device (OCL 503). The agent consists of biodegradable poly-lactic-co-glycolic acid microspheres (150-212 {mu}m) coated with type I bovine collagen and was compared with Embosphere{sup Registered-Sign} Microspheres (300-500 {mu}m) in this controlled study of uterine artery embolization (UAE) in sheep. Methods: Unilateral UAE was performed in 32 adult ewes randomly assigned. Vessels were embolized to effective stasis. The cohort was divided into four groups, which were sacrificed at 1, 3, 6, and 12 months. Results: Both agents were 100% effective in achieving stasis. At 6 months, all OCL 503-treated arteries were occluded, the microspheres degraded with time, and at 12 months all four animals examined demonstrated recanalization. OCL 503 was found in the untreated uterine artery in one animal with no other evidence of non target embolization. In the Embosphere-treated group, all vessels remained occluded and microspheres were detected in the contralateral uterine artery in 6 of 15 examined vessels and in 10 vaginal, 2 ovarian, and 1 vesical artery. No procedural-related complications were seen in either group. Conclusions: OCL 503 is as effective an embolic agent as Embosphere{sup Registered-Sign} Microspheres when embolizing ovine uterine arteries and resorbs with time, allowing recanalization of the treated arteries. No device-related issues or adverse events were observed.

  4. Manufacturing

    Energy Savers [EERE]

    Than $2 Billion in Energy Costs; Program Expands to Help America's Water Systems | Department of Energy Manufacturers in U.S. Energy Department's Better Plants Program Save More Than $2 Billion in Energy Costs; Program Expands to Help America's Water Systems Manufacturers in U.S. Energy Department's Better Plants Program Save More Than $2 Billion in Energy Costs; Program Expands to Help America's Water Systems September 30, 2015 - 9:03am Addthis NEWS MEDIA CONTACT (202) 586-4940

  5. Micro Power Trading Co | Open Energy Information

    Open Energy Info (EERE)

    Micro Power Trading Co Jump to: navigation, search Name: Micro Power Trading Co Place: Singapore Product: Silicon ingots manufacturer. References: Micro Power Trading Co1 This...

  6. Mark Johnson | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Mark Johnson About Us Mark Johnson - Advanced Manufacturing Office Director Mark Johnson, Ph.D., serves as the Director of the Advanced Manufacturing Office (AMO) in the Office of Energy Efficiency and Renewable Energy (EERE). AMO is focused on creating a fertile innovation environment for advanced manufacturing, enabling vigorous domestic development of new energy-efficient manufacturing processes and materials technologies to reduce the energy intensity and life-cycle energy consumption of

  7. Solar Trade Corporation STC | Open Energy Information

    Open Energy Info (EERE)

    Trade Corporation STC Jump to: navigation, search Name: Solar Trade Corporation (STC) Place: Lowell, Massachusetts Zip: 01851-4519 Sector: Solar Product: US manufacturer of solar...

  8. Comparison of the Epson Expression 1680 flatbed and the Vidar VXR-16 Dosimetry PRO trade mark sign film scanners for use in IMRT dosimetry using Gafchromic and radiographic film

    SciTech Connect (OSTI)

    Wilcox, Ellen; Daskalov, George; Nedialkova, Lucy

    2007-01-15

    Intensity-modulated radiotherapy (IMRT) treatment plan verification is often done using Kodak EDR2 film and a Vidar Dosimetry PRO trade mark sign film digitizer. However, since many hospitals are moving towards a filmless environment, access to a film processor may not be available. Therefore, we have investigated a newly available Gafchromic[reg] EBT film for IMRT dosimetry. Planar IMRT dose distributions are delivered to both EBT and EDR2 film and scanned with the Vidar VXR-16 as well as an Epson Expression 1680 flatbed scanner. The measured dose distributions are then compared to those calculated with a Pinnacle treatment planning system. The IMRT treatments consisted of 7-9 6 MV beams for treatment of prostate, head and neck, and a few other sites. The films were analyzed using FilmQA trade mark sign (3cognition LLC) software. Comparisons between measured and calculated dose distributions are reported as dose difference (DD) (pixels within {+-}5%), distance to agreement (DTA) (3 mm), as well as gamma values ({gamma}) (dose={+-}3%, dist.=2 mm). Using EDR2 with the Vidar scanner is an established technique and agreement between calculated and measured dose distributions was better than 90% in all indices (DD, DTA, and {gamma}). However, agreement with calculations deteriorated reaching the lower 80% for EBT film scans with the Vidar scanner in logarithmic mode. The EBT Vidar scans obtained in linear mode showed an improved agreement to the upper 80% range, but artifacts were still observed across the scan. These artifacts were very distinct in all EBT scans and can be attributed to the way the film is transported through the scanner. In the Epson scanner both films are rigidly immobilized and the light source scans over the film. It was found that the Epson scanner performed equally well with both types of film giving agreement to better than 90% in all indices.

  9. Mark Bowers

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mark Bowers A Can-Do Attitude about Life Mark Bowers, optics manager and sailing enthusiast, is shown sailing in the San Francisco Bay. It is quickly clear that Mark Bowers, optical systems project associate manager, loves learning and sharing knowledge with others, both on and off the job. His enthusiasm allows him to enliven even typically dull events such as weekly safety meetings. Knowing that the best way to encourage attendance and disseminate important information at the weekly meetings

  10. Mark Herrmann

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mark Herrmann Mark Herrmann Director, National Ignition Facility NIF Director Mark Herrmann came to LLNL in October 2014 from Sandia National Laboratories, where he served as director of the Pulsed Power Sciences Center. As the NIF Director, Herrmann works closely with the leadership of the National Nuclear Security Administration's Stockpile Stewardship Program (SSP) across the weapons complex including the national Inertial Confinement Fusion (ICF) Program, as well as the National Security

  11. AMO Director Mark Johnson Moderates Panel at American Energy...

    Office of Environmental Management (EM)

    Director Mark Johnson Moderates Panel at American Energy & Manufacturing Competitiveness (AEMC) Northeast Regional Summit AMO Director Mark Johnson Moderates Panel at American ...

  12. Oak Ridge Centers for Manufacturing Technology - The Manufacturing...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The Manufacturing Skills Campus Another of the inputs came from Garry Whitley, President of the Atomic Trades and Labor Council, since retired. Garry and I have worked together...

  13. Oak Ridge Centers for Manufacturing Technology ? The Manufacturing...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The Manufacturing Skills Campus Another of the inputs came from Garry Whitley, President of the Atomic Trades and Labor Council, since retired. Garry and I have worked together...

  14. Mark Lausten

    Broader source: Energy.gov [DOE]

    Mark is a registered professional engineer with a background in the power industry engineering, procurement, and construction. He began work for the Solar Energy Technologies Office in 2007, focusing on market barriers to large-scale solar deployment. Now working on the SunShot Initiative team, he has watched the state of the concentrating solar power (CSP) market change from nearly barren to flourishing.

  15. ZYGO Mark Ivxp Interferometer

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ZYGO Mark Ivxp Interferometer Back to Equipment

  16. AMO Director Mark Johnson Moderates Panel at American Energy &

    Office of Environmental Management (EM)

    Manufacturing Competitiveness (AEMC) Northeast Regional Summit | Department of Energy Director Mark Johnson Moderates Panel at American Energy & Manufacturing Competitiveness (AEMC) Northeast Regional Summit AMO Director Mark Johnson Moderates Panel at American Energy & Manufacturing Competitiveness (AEMC) Northeast Regional Summit May 17, 2016 - 1:00pm Addthis From left to right: Moderator Mark Johnson, panelists Dr. Craig Blue, Dean Jones, John Milton-Benoit, Jeffrey Wilcox, and

  17. Mark Holecek | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Mark Holecek Manager - Kansas City Field Office Mark Holecek Mark Holecek serves as the Manager for the National Nuclear Security Administration's (NNSA) Kansas City Field Office (KCFO). In this position, he has day-to-day responsibility for NNSA operations under the Kansas City Plant contract. This includes operations in Kansas City, Albuquerque, Los Alamos, and Ft. Chaffee and covers a diverse set of manufacturing and procurement activities for NNSA and national security customers. Products

  18. Agenda: Fiber Reinforced Polymer Composite Manufacturing Workshop

    Energy Savers [EERE]

    Advanced Manufacturing Office (AMO) manufacturing.energy.gov 3 Morning Agenda 9:00am - 9:05am Welcome Mark Johnson Director, Advanced Manufacturing Office 9:05am - 9:20am Clean Energy Manufacturing Initiative David Danielson Assistant Secretary Energy Efficiency and Renewable Energy 9:20am - 9:50am Advanced Manufacturing Office Overview and Review of RFI Results Mark Johnson Director, Advanced Manufacturing Office 9:50am - 10:30am Panel Discussion: DOE Perspectives Mark Shuart, Advanced

  19. Additive Manufacturing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MST » MST Research Programs » Additive Manufacturing Additive Manufacturing A method allowing unparalleled manufacturing control, data visualization, and high-value parts repair. Through additive manufacturing, Los Alamos is developing materials for the future. Taking complex manufacturing challenges from design to fabrication. A science and engineering approach for additive manufacturing solutions. Get Expertise John Carpenter Technical Staff Member Metallurgy Email Division Leader Materials

  20. Trade Adjustment Assistance Community College and Career Training Grant

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Program (TAACCCT) Energy and Manufacturing Awards and Topics List | Department of Energy Trade Adjustment Assistance Community College and Career Training Grant Program (TAACCCT) Energy and Manufacturing Awards and Topics List Trade Adjustment Assistance Community College and Career Training Grant Program (TAACCCT) Energy and Manufacturing Awards and Topics List View a list of all current Trade Adjustment Assistance Community College and Career Training (TAACCCT) grant program awards

  1. Trade Adjustment Assistance Community College and Career Training...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Career Training Grant Program (TAACCCT) Energy and Manufacturing Awards and Topics List Trade Adjustment Assistance Community College and Career Training Grant Program ...

  2. Additive Manufacturing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    manufacturing and national security To realize additive manufacturing's potential as a disruptive technology for Los Alamos National Laboratory's national security missions,...

  3. Manufacturing Innovation Institute for Smart Manufacturing: Advanced...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Manufacturing Innovation Institute for Smart Manufacturing: Advanced Sensors, Controls, Platforms, and Modeling for Manufacturing Manufacturing Innovation Institute for Smart ...

  4. Mark R. Lochbaum

    Broader source: Energy.gov [DOE]

    Mark Lochbaum is a Lead Small Business Specialist with Office of Small and Disadvantaged Business Utilization.Prior to joining the U.S. Department of Energy, Mark worked at the U.S. Department of...

  5. Method of intrinsic marking

    DOE Patents [OSTI]

    Adams, David P; McDonald, Joel Patrick; Jared, Bradley Howell; Hodges, V. Carter; Hirschfeld, Deidre; Blair, Dianna S

    2014-04-01

    A method of pulsed laser intrinsic marking can provide a unique identifier to detect tampering or counterfeiting.

  6. Howard S. Marks

    Broader source: Energy.gov [DOE]

    Howard Marks is a Program Analyst with the Office of Energy Efficiency and Renewable Energy's Biomass Program.

  7. mark | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Ames Laboratory Profile Mark Gordon Associate Chemical & Biological Sciences 201 Spedding ... Group Ames Laboratory Research Projects: Chemical Physics TheoreticalComputational Tools ...

  8. NREL: Energy Analysis - Mark Ruth

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mark Ruth Photo of Mark Ruth. Mark Ruth is the principal project lead of the Strategic Energy Analysis Center. Principal Project Lead - Integrated Energy System Model On staff...

  9. 2012 Solid-State Lighting Manufacturing R&D Workshop Presentations...

    Energy Savers [EERE]

    Mark Hand, Acuity Brands Lighting Perspective on Manufacturing the L Prize Award Winning LED Bulb Craig Fenske, Philips Lighting Systems and Controls Trends in Manufacturable ...

  10. 2014 Solid-State Lighting Manufacturing R&D Workshop Presentations...

    Energy Savers [EERE]

    for Lighting Mark Hand, Acuity Brands Panel: U.S. Manufacturing Status and Trends ... Bland, SB Consulting LED Track Session Panel: Advances in Manufacturing and Application ...

  11. Congressman Mark Takai

    Broader source: Energy.gov [DOE]

    Mark Takai was born and raised on Oahu, Hawaii. He was a 20 year member of the Hawaii State House of Representatives before being elected to Congress. He represented the district of Aiea/Pearl City...

  12. CMPC Marking Resource

    Broader source: Energy.gov (indexed) [DOE]

    All documents containing Nuclear Weapon Data that wereare originated in the DOE or NNSA and transmitted to the DoD, must also be marked Critical Nuclear Weapon Design...

  13. Manufacturing Glossary

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Energy Efficiency Web Site. If you need assistance in viewing this page, please call (202) 586-8800 Home > Energy Users > Energy Efficiency Page > Glossary for the Manufacturing...

  14. Manufacturing technologies

    SciTech Connect (OSTI)

    1995-09-01

    The Manufacturing Technologies Center is an integral part of Sandia National Laboratories, a multiprogram engineering and science laboratory, operated for the Department of Energy (DOE) with major facilities at Albuquerque, New Mexico, and Livermore, California. Our Center is at the core of Sandia`s Advanced Manufacturing effort which spans the entire product realization process.

  15. Sustainable Manufacturing

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Principal Investigator (Presenter): Dr. Troy D. Marusich , CTO Washington, D.C. May 6-7, 2014 Third Wave Systems Inc. U.S. DOE Advanced Manufacturing Office Peer Review Meeting ...

  16. Innovative Manufacturing Initiative Recognition Day, Advanced Manufacturing

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Office (AMO) | Department of Energy Day, Advanced Manufacturing Office (AMO) Innovative Manufacturing Initiative Recognition Day, Advanced Manufacturing Office (AMO) PDF icon imi_recogitionday_leo_june2012.pdf More Documents & Publications Innovative Manufacturing Initiative Recognition Day Advanced Manufacturing Office Overview Unlocking the Potential of Additive Manufacturing in the Fuel Cells Industry

  17. U.S. Advanced Manufacturing and Clean Energy Technology Challenges

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    U.S. Advanced Manufacturing and Clean Energy Technology Challenges May 6, 2014 AMO Peer Review Mark Johnson Director Advanced Manufacturing Office www.manufacturing.energy.gov This presentation does not contain any proprietary, confidential, or otherwise restricted information. 2 Outline * Big Picture on Manufacturing in US * Focus on Advanced Manufacturing * AMO Organization * Technical Assistance * R&D Facilities * R&D Projects * Goals for Meeting 3 Products invented here, now made

  18. Welcome! Presentation: Fiber Reinforced Polymer Composite Manufacturing Workshop

    Energy Savers [EERE]

    5 | Energy Efficiency and Renewable Energy eere.energy.gov Mark Johnson Director Advanced Manufacturing Office manufacturing.energy.gov Breakout Instructions January 13, 2014 Advanced Manufacturing Office (AMO) manufacturing.energy.gov 6 Breakout Objectives Let's dig deeper: * Manufacturing Process Technologies - Blue Teams A and B (e.g. lay-up techniques, out of the autoclave, novel cure techniques, resin infusion, pultrusion, SMC, tooling, machining) * Enabling Technologies and Approaches -

  19. Manufacturing Innovation Institute for Smart Manufacturing: Advanced

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Sensors, Controls, Platforms, and Modeling for Manufacturing | Department of Energy Manufacturing Innovation Institute for Smart Manufacturing: Advanced Sensors, Controls, Platforms, and Modeling for Manufacturing Manufacturing Innovation Institute for Smart Manufacturing: Advanced Sensors, Controls, Platforms, and Modeling for Manufacturing September 23, 2015 - 2:38pm Addthis Posted Date: Sep 15, 2015 Original Closing Date for Applications: Jan 29, 2016 A mandatory Concept Paper is due

  20. Mark F. Davis | Bioenergy | NREL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mark D. Mitchell About Us Mark D. Mitchell - Communications Support Contractor to ARPA-E Mark Mitchell is a Communications Support Contractor to ARPA-E. Most Recent ARPA-E Celebrates Five Years of Changing What's Possible April 28 Energy Innovators to Convene for 2014 ARPA-E Summit February 20 Interview with ARPA-E: The Future of Semiconductors February 4

    F. Davis Mark F. Davis Acting Center Director, Biosciences Mark.Davis@nrel.gov | 303-384-6140 Research Interests Dr. Mark Davis is serving

  1. Mark R. Nimlos | Bioenergy | NREL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mark R. Lochbaum About Us Mark R. Lochbaum - Lead Small Business Specialist Mark R. Lochbaum Mark Lochbaum is a Lead Small Business Specialist with Office of Small and Disadvantaged Business Utilization. Prior to joining the U.S. Department of Energy, Mark worked at the U.S. Department of Veterans Affairs (VA) as a Contracting Officer. There, he procured a wide variety of items and services in support of the VA mission, with a primary focus on small business acquisitions. Mark holds a Masters of

  2. additive manufacturing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    additive manufacturing - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management Programs Advanced

  3. Green Manufacturing

    SciTech Connect (OSTI)

    Patten, John

    2013-12-31

    Green Manufacturing Initiative (GMI): The initiative provides a conduit between the university and industry to facilitate cooperative research programs of mutual interest to support green (sustainable) goals and efforts. In addition to the operational savings that greener practices can bring, emerging market demands and governmental regulations are making the move to sustainable manufacturing a necessity for success. The funding supports collaborative activities among universities such as the University of Michigan, Michigan State University and Purdue University and among 40 companies to enhance economic and workforce development and provide the potential of technology transfer. WMU participants in the GMI activities included 20 faculty, over 25 students and many staff from across the College of Engineering and Applied Sciences; the College of Arts and Sciences' departments of Chemistry, Physics, Biology and Geology; the College of Business; the Environmental Research Institute; and the Environmental Studies Program. Many outside organizations also contribute to the GMI's success, including Southwest Michigan First; The Right Place of Grand Rapids, MI; Michigan Department of Environmental Quality; the Michigan Department of Energy, Labor and Economic Growth; and the Michigan Manufacturers Technical Center.

  4. DOE Warns Manufacturers Who Submitted Incomplete Certification Reports

    Broader source: Energy.gov [DOE]

    Washington, DC - The Department of Energy’s Office of General Counsel has sent warning letters to 9 manufacturers or trade associations that submitted incomplete energy-efficiency test data to...

  5. Fuel Cell Manufacturing: American Energy and Manufacturing Competitive...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fuel Cell Manufacturing: American Energy and Manufacturing Competitiveness Summit Fuel Cell Manufacturing: American Energy and Manufacturing Competitiveness Summit Presentation on ...

  6. Advanced Manufacturing Office: Smart Manufacturing Industry Day...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Smart Manufacturing is a network data-driven process that combines innovative automation ... Smart Manufacturing is a network data-driven process that combines innovative automation ...

  7. ALL GRADE 5 AND GRADE 8 FASTENERS WHICH DO NOT BEAR ANY MANUFACTURERS'

    Energy Savers [EERE]

    ALL GRADE 5 AND GRADE 8 FASTENERS WHICH DO NOT BEAR ANY MANUFACTURERS' HEADMARKS Grade 5 Grade 8 GRADE 5 FASTENERS WITH THE FOLLOWING MANUFACTURERS' HEADMARKS: GRADE 8 FASTENERS WITH THE FOLLOWING MANUFACTURERS' HEADMARKS: MARK KS MARK J (CA TW JP YU) (Greater than 1/2 inch dia) MARK A NF H M MS Hollow Triangle E MARK KS RT FM KY J UNY A KS RT KY J UNY NF H M MS E FM GRADE 8.2 FASTENERS WITH THE FOLLOWING HEADMARKS: MARK KS KS J KS GRADE A325 FASTENERS WITH THE FOLLOWING HEADMARKS: MARK A325 KS

  8. Mark Gilbertson | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Gilbertson About Us Mark Gilbertson - Deputy Assistant Secretary, Site Restoration for Environmental Management Photo of Mark Gilbertson Mr. Mark Gilbertson is currently the Deputy Assistant Secretary (DAS) for Site Restoration within the Office of Environmental Management (EM). He is leading the organization responsible for the remediation of the environmental legacy resulting from five decades of nuclear weapons development and Government-sponsored nuclear energy research. Integral to that

  9. Mark Whitney | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Whitney About Us Mark Whitney - Principal Deputy Assistant Secretary for Environmental Management Mark Whitney Mr. Mark Whitney was named Principal Deputy Assistant Secretary for the U.S. Department of Energy (DOE) Office of Environmental Management (EM) in May 2014. A member of the U.S. Senior Executive Service for more than nine years, Mr. Whitney joined DOE in 2005 and has served EM and the National Nuclear Security Administration. Mr. Whitney has held several key DOE positions in which he

  10. Solar Manufacturing Projects | Department of Energy

    Energy Savers [EERE]

    Solar Manufacturing Projects Solar Manufacturing Projects Solar Manufacturing Projects Solar Manufacturing Projects Solar Manufacturing Projects Solar Manufacturing Projects SOLAR ...

  11. DOE and Federal Energy and Manufacturing Workforce Programs and

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Infrastructure Location List | Department of Energy DOE and Federal Energy and Manufacturing Workforce Programs and Infrastructure Location List DOE and Federal Energy and Manufacturing Workforce Programs and Infrastructure Location List View a list of DOE and federal workforce programs and infrastructure, cataloged by city and state. This list contains most of the programs included in our Energy & Manufacturing Topics list and Trade Adjustment Assistance Community College and Career

  12. Manufacturing Demonstration Facility

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ORNL is managed by UT-Battelle for the US Department of Energy Manufacturing Demonstration Facility DOE Advanced Manufacturing Office Merit Review Craig Blue Director, Manufacturing Demonstration Facility Energy and Environmental Sciences Directorate May 6-7, 2014 Washington, DC This presentation does not include proprietary, confidential, or otherwise restricted information. Outline * Manufacturing Demonstration Facility * Impacts with Industry - Metal additive manufacturing - Polymer additive

  13. WIPP_Marks_12_Years

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Marks 12 Years of Operations CARLSBAD, N.M., March 28, 2011 - On Saturday, March 26, 2011, ... It has now been 12 years since WIPP received its first shipment of transuranic (TRU) ...

  14. Mark A. McCall

    Broader source: Energy.gov [DOE]

    [[{"type":"media","view_mode":"media_large","fid":"964941","attributes":{"alt":"Mark McCall_Headshot_August 2015.jpg","class":"media-image caption","height":"480","style":"width: 384px; height:...

  15. Mark Higgins | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Higgins About Us Mark Higgins - Operations Supervisor, Wind & Water Power Technologies Office Mark Higgins is the Operations Supervisor for the Wind & Water Power Technologies Office. Most Recent Keeping America Competitive: Bringing Down the Cost of Small Wind Turbines January 23 Innovative Deepwater Platform Aims to Harness Offshore Wind and Wave Power March 28 Mt. Wachusett Community College Makes Huge Investment in Wind Power March 1

  16. The Advanced Manufacturing Partnership and the Advanced Manufacturing...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    The Advanced Manufacturing Partnership and the Advanced Manufacturing National Program Office The Advanced Manufacturing Partnership and the Advanced Manufacturing National Program ...

  17. Manufacturing Demonstration Facility

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    to develop broad dissemination of additive manufacturing Industry Collaborations * ... 5 DOE-AMO 2015 Peer Review Understanding Additive Manufacturing Mainstream applications ...

  18. Next Generation Manufacturing Processes

    Broader source: Energy.gov [DOE]

    New process technologies can rejuvenate U.S. manufacturing. Novel processing concepts can open pathways to double net energy productivity, enabling rapid manufacture of energy-efficient, high...

  19. HPC4Manufacturing

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Lab capabilities Manufacturing domain expertise National mission and guidance Bringing HPC to U.S. Manufacturers Energy Efficient Processes Energy Efficient Products...

  20. Mark Mathias > General Motors - Fuel Cell Research > Scientific Advisory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mark Holecek Manager - Kansas City Field Office Mark Holecek Mark Holecek serves as the Manager for the National Nuclear Security Administration's (NNSA) Kansas City Field Office (KCFO). In this position, he has day-to-day responsibility for NNSA operations under the Kansas City Plant contract. This includes operations in Kansas City, Albuquerque, Los Alamos, and Ft. Chaffee and covers a diverse set of manufacturing and procurement activities for NNSA and national security customers. Products

  1. Carbon Trading Protocols for Geologic Sequestration

    SciTech Connect (OSTI)

    Hoversten, Shanna

    2008-08-07

    Carbon capture and storage (CCS) could become an instrumental part of a future carbon trading system in the US. If the US starts operating an emissions trading scheme (ETS) similar to that of the European Union's then limits on CO{sub 2} emissions will be conservative in the beginning stages. The government will most likely start by distributing most credits for free; these free credits are called allowances. The US may follow the model of the EU ETS, which during the first five-year phase distributed 95% of the credits for free, bringing that level down to 90% for the second five-year phase. As the number of free allowances declines, companies will be forced to purchase an increasing number of credits at government auction, or else obtain them from companies selling surplus credits. In addition to reducing the number of credits allocated for free, with each subsequent trading period the number of overall credits released into the market will decline in an effort to gradually reduce overall emissions. Companies may face financial difficulty as the value of credits continues to rise due to the reduction of the number of credits available in the market each trading period. Governments operating emissions trading systems face the challenge of achieving CO{sub 2} emissions targets without placing such a financial burden on their companies that the country's economy is markedly affected.

  2. MEMORANDUM FOR NEPA FILE FROM: MARK LUSK NEPA DOCUMENT MANAGER

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    February 11, 2011 MEMORANDUM FOR NEPA FILE FROM: MARK LUSK NEPA DOCUMENT MANAGER SUBJECT: Supplement Analysis for the Saft America, Inc. Electric Drive Vehicle Battery and Component Manufacturing Initiative Application, Jacksonville, Florida (DOE/EA-1711) UNew InformationU : Proposed Minor Change to Saft America, Inc. Proposed Project U LocationU : Saft America, Inc. Plant at the Cecil Commerce Center, near Jacksonville, Florida, in Duval County UProposed ByU : Saft America, Inc. 1. U

  3. Advanced Manufacturing Technician

    Broader source: Energy.gov [DOE]

    Alternate Title(s):Manufacturing Production Technician; Electro-Mechanical Technician; Electronics Maintenance Technician  

  4. Advanced Manufacturing Office News

    SciTech Connect (OSTI)

    2013-08-08

    News stories about advanced manufacturing, events, and office accomplishments. Subscribe to receive updates.

  5. World Trade Organization | Open Energy Information

    Open Energy Info (EERE)

    of the WTO's agreed rules for trade in goods, trade in services, and trade-related intellectual property rights monitoring and reviewing the trade policies of our members,...

  6. Manufacturing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Science & Innovation » Energy Efficiency » Manufacturing Manufacturing Additive manufacturing, also know as 3D printing, has helped spark a creative manufacturing renaissance, allowing companies to create products in new ways while also reducing material waste, saving energy and shortening the time needed to bring products to market. Learn more about this game-changing technology. Manufacturing is the lifeblood of the American economy -- providing jobs for hard working American families

  7. Manufacturing Supply Chain

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Administration (EIA) ‹ Consumption & Efficiency Manufacturing Energy Consumption Survey (MECS) Glossary › FAQS › Overview Data 2010 2006 2002 1998 1994 1991 Archive Analysis & Projections Cost of Natural Gas Used in Manufacturing Sector Has Fallen Graph showing Cost of Natural Gas Used in Manufacturing Sector Has Fallen Source: U.S. Energy Information Administration, Manufacturing Energy Consumption Survey (MECS) 1998-2010, September 6, 2013. New 2010 Manufacturing Energy

  8. Congressional House Senate Current Request Marks Marks Approp

    Energy Savers [EERE]

    2 FY 2012 FY 2012 FY 2012 ($ in thousands) Congressional House Senate Current Request Marks Marks Approp FOSSIL ENERGY R&D Coal 291,358 289,415 291,358 359,320 Natural Gas Technologies 0 15,000 0 14,575 Unconventional Fossil Energy Technologies 0 0 0 4,858 Program Direction 159,233 120,847 151,729 119,929 Plant & Capital Equipment 16,794 16,794 16,794 16,794 Environmental Restoration 7,897 7,897 7,897 7,897 Special Recruitment Program 700 700 700 700 Subtotal, Fossil Energy R&D

  9. Part IV: Section D - Packaging and Marking

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PART I SECTION D PACKAGING AND MARKING DE-AC36-08GO28308 Modification M901 Section D - Page ii PART I SECTION D PACKAGING AND MARKING TABLE OF CONTENTS D.1 Packaging 1 D.2 Marking ...

  10. Mark Jankowski: Minnesota Pollution Control Agency

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mark Jankowski: Minnesota Pollution Control Agency Alumni Link: Opportunities, News and ... Latest Issue:September 2015 all issues All Issues submit Mark Jankowski: Minnesota ...

  11. Mark Henson | Photosynthetic Antenna Research Center

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mark Henson February 16, 2012 Mark Henson "Modeling the Production of Microalgal Biodiesel" Published: February 16, 2012 Event Information can be found HERE E An error occurred....

  12. Signature of Mark Holecek Signature of Mark Holecek Signature of Ralph B Tennants II

    National Nuclear Security Administration (NNSA)

    Mark Holecek Signature of Mark Holecek Signature of Ralph B Tennants II Signature of Ralph B Tennants II

  13. Energy Use in Manufacturing

    Reports and Publications (EIA)

    2006-01-01

    This report addresses both manufacturing energy consumption and characteristics of the manufacturing economy related to energy consumption. In addition, special sections on fuel switching capacity and energy-management activities between 1998 and 2002 are also featured in this report.

  14. Manufacturing Day 2015

    Broader source: Energy.gov [DOE]

    All over the country, manufacturing companies and other organizations are preparing to host an anticipated 400,000 people who want to experience U.S. manufacturing up close and in person. On...

  15. NREL: Innovation Impact - Manufacturing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Manufacturing Menu Home Home Solar Solar Wind Wind Analysis Analysis Bioenergy Bioenergy Buildings Buildings Transportation Transportation Manufacturing Manufacturing Energy Systems Integration Energy Systems Integration Increasing U.S. Market Share in Solar Photovoltaic Manufacturing Close From 2000 to 2010, global shipments of solar cells and modules grew 53%, a wave that China and Taiwan rode to increase their combined market share from less than 2% to 54%. Meanwhile, U.S. market share

  16. Manufacturing Innovation Topics Workshop

    Broader source: Energy.gov [DOE]

    The Advanced Manufacturing Office (AMO) and the Office of the Secretary of Defense Manufacturing Technology Program (OSD ManTech) will host a workshop to discuss AMO's recent Request for Information (RFI) on Clean Energy Manufacturing Topic Areas as well as the recent areas of interest announced by OSD ManTech for a new Manufacturing Innovation Institute on October 8-9, 2014 in Fort Worth, TX.

  17. Bio-Manufacturing: A Strategic clean energy manufacturing opportunity...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Bio-Manufacturing: A Strategic clean energy manufacturing opportunity Bio-Manufacturing: A ... Volume 1, No.2 NRELDOE EERE QCMetrology Workshop - EERE Fuel Cell Technologies Office ...

  18. The Mark III vertex chamber

    SciTech Connect (OSTI)

    Adler, J.; Bolton, T.; Bunnell, K.; Cassell, R.; Cheu, E.; Freese, T.; Grab, C.; Mazaheri, G.; Mir, R.; Odian, A.

    1987-07-01

    The design and construction of the new Mark III vertex chamber is described. Initial tests with cosmic rays prove the ability of track reconstruction and yield triplet resolutions below 50 ..mu..m at 3 atm using argon/ethane (50:50). Also performed are studies using a prototype of a pressurized wire vertex chamber with 8 mm diameter straw geometry. Spatial resolution of 35mm was obtained using dimethyl ether (DME) at 1 atm and 30 ..mu..m using argon/ethane (50/50 mixture) at 4 atm. Preliminary studies indicate the DME to adversely affect such materials as aluminized Mylar and Delrin.

  19. Los Alamos National Laboratory marks

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    marks 20 years without full-scale nuclear testing September 26, 2012 LOS ALAMOS, New Mexico, Sept. 26, 2012-Two decades ago the last full-scale underground test of a nuclear weapon was conducted by Los Alamos National Laboratory at the Nevada Test Site. The test, code named "Divider," was detonated on Sept. 23, 1992 as the last of an eight-test series called "Julin." The test had an announced yield less than the equivalent of 20,000 tons of TNT. The purpose of the test, also

  20. Semantic Web for Manufacturing Web Services

    SciTech Connect (OSTI)

    Kulvatunyou, Boonserm; Ivezic, Nenad

    2002-06-01

    As markets become unexpectedly turbulent with a shortened product life cycle and a power shift towards buyers, the need for methods to rapidly and cost-effectively develop products, production facilities and supporting software is becoming urgent. The use of a virtual enterprise plays a vital role in surviving turbulent markets. However, its success requires reliable and large-scale interoperation among trading partners via a semantic web of trading partners' services whose properties, capabilities, and interfaces are encoded in an unambiguous as well as computer-understandable form. This paper demonstrates a promising approach to integration and interoperation between a design house and a manufacturer by developing semantic web services for business and engineering transactions. To this end, detailed activity and information flow diagrams are developed, in which the two trading partners exchange messages and documents. The properties and capabilities of the manufacturer sites are defined using DARPA Agent Markup Language (DAML) ontology definition language. The prototype development of semantic webs shows that enterprises can widely interoperate in an unambiguous and autonomous manner; hence, virtual enterprise is realizable at a low cost.

  1. Fuel Cell Manufacturing: American Energy and Manufacturing Competitiveness Summit

    Broader source: Energy.gov [DOE]

    Presentation on fuel cell manufacturing by Sunita Satyapal at the American Energy and Manufacturing Competitiveness Summit on December 12, 2013.

  2. QER- Comment of Mark Ladd

    Broader source: Energy.gov [DOE]

    Pleases count me in as a very concerned and upset constituant of Conway , Ma. The proposed TNG pipeline through our town , or any town for that matter is sucker punch in the face for all of us. I am very disappointed with Deval Patrick's decision to support a multi billionaire from Houston to jeopordize everyone in the pipeline's path and beyond. This pipeline is a such a bad idea that it could actually be pushed down people's throats because it's so unthinkably bad, surly some government official would protect us from it !!!!! WRONG , big corporations rule everywhere , even in the town I love so much .I do not support this ridiculous project for so many reasons , I truly don't know where to start. Please reject this pipeline. Mark Ladd

  3. A Semantic Web Service and Simulation Framework to Intelligent Distributed Manufacturing

    SciTech Connect (OSTI)

    Son, Young Jun; Kulvatunyou, Boonserm; Cho, Hyunbo; Feng, Shaw

    2005-11-01

    To cope with today's fluctuating markets, a virtual enterprise (VE) concept can be employed to achieve the cooperation among independently operating enterprises. The success of VE depends on reliable interoperation among trading partners. This paper proposes a framework based on semantic web of manufacturing and simulation services to enable business and engineering collaborations between VE partners, particularly a design house and manufacturing suppliers.

  4. Additive Manufacturing: Going Mainstream

    Broader source: Energy.gov [DOE]

    Additive manufacturing, or 3D printing, is receiving attention from media, investment communities and governments around the world transforming it from obscurity to something to be talked about.

  5. Manufacturing R&D

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    such as metrology and quality control standards, modeling and simulation tools ... the establishment of a robust, domestic hydrogen and fuel cell manufacturing industry. ...

  6. Manufacturing | Department of Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    in the production of clean energy technologies like electric vehicles, LED bulbs and solar panels. The Department is also working with manufacturers to increase their energy...

  7. Contribution to Nanotechnology Manufacturing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    50 award for directed assembly September 3, 2008 Contribution to Nanotechnology Manufacturing LOS ALAMOS, New Mexico, September 3, 2008-A team of scientists spanning three...

  8. Roll to Roll Manufacturing

    SciTech Connect (OSTI)

    Daniel, Claus

    2015-06-09

    ORNL researchers are developing roll to roll technologies for manufacturing, automotive, and clean energy applications in collaboration with industry partners such as Eastman Kodak.

  9. Mark Vermilyea | Inventors | GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mark Vermilyea Mark Vermilyea Mechanical Engineer Composites Click to email this to a friend (Opens in new window) Share on Facebook (Opens in new window) Click to share (Opens in new window) Click to share on LinkedIn (Opens in new window) Click to share on Tumblr (Opens in new window) "I enjoy the technical and interpersonal challenges of working across research and development teams to solve complicated interdisciplinary problems." -Mark Vermilyea Mark's view of the future? It

  10. Clean Energy Manufacturing Initiative

    SciTech Connect (OSTI)

    2013-04-01

    The initiative will strategically focus and rally EEREs clean energy technology offices and Advanced Manufacturing Office around the urgent competitive opportunity for the United States to be the leader in the clean energy manufacturing industries and jobs of today and tomorrow.

  11. International Trade of Biofuels (Brochure)

    SciTech Connect (OSTI)

    Not Available

    2013-05-01

    In recent years, the production and trade of biofuels has increased to meet global demand for renewable fuels. Ethanol and biodiesel contribute much of this trade because they are the most established biofuels. Their growth has been aided through a variety of policies, especially in the European Union, Brazil, and the United States, but ethanol trade and production have faced more targeted policies and tariffs than biodiesel. This fact sheet contains a summary of the trade of biofuels among nations, including historical data on production, consumption, and trade.

  12. Manufacturing Energy and Carbon Footprint

    Energy Savers [EERE]

    ORNL is managed by UT-Battelle for the US Department of Energy Manufacturing Demonstration Facility DOE Advanced Manufacturing Office Merit Review Craig Blue Director, Manufacturing Demonstration Facility Energy and Environmental Sciences Directorate May 6-7, 2014 Washington, DC This presentation does not include proprietary, confidential, or otherwise restricted information. Outline * Manufacturing Demonstration Facility * Impacts with Industry - Metal additive manufacturing - Polymer additive

  13. The Advanced Manufacturing Partnership and the Advanced Manufacturing

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    National Program Office | Department of Energy The Advanced Manufacturing Partnership and the Advanced Manufacturing National Program Office The Advanced Manufacturing Partnership and the Advanced Manufacturing National Program Office This presentation describes the Advanced Manufacturing Partnership from its beginning as a recommendation of the President's Council of Advisers on Science and Technology to its development and organization. PDF icon The Advanced Manufacturing Partnership and

  14. Bio-Manufacturing: A Strategic clean energy manufacturing opportunity |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Bio-Manufacturing: A Strategic clean energy manufacturing opportunity Bio-Manufacturing: A Strategic clean energy manufacturing opportunity Breakout Session 1: New Developments and Hot Topics Session 1-A: Biomass and the U.S. Competitive Advantages for Manufacturing Clean Energy Products Libby Wayman, Director, EERE Clean Energy Manufacturing Initiative PDF icon b13_wayman_1-a.pdf More Documents & Publications Amped Up! Volume 1, No.2 NREL/DOE EERE QC/Metrology

  15. Renewable Energy Manufacturing Program

    Broader source: Energy.gov [DOE]

    Note: The initial application deadline for the Renewable Energy Manufacturing Program is June 30, 2016. Applications will be accepted following that date only if there are remaining funds available...

  16. NREL: Innovation Impact - Manufacturing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Buildings Menu Home Home Solar Solar Wind Wind Analysis Analysis Bioenergy Bioenergy Buildings Buildings Transportation Transportation Manufacturing Manufacturing Energy Systems Integration Energy Systems Integration Buildings Use 40% of U.S. Energy Close Americans spend $400 billion annually to power homes and commercial buildings. An estimated $80 billion could be saved through energy efficiency. Close NREL's net-zero-energy Research Support Facility employs cutting-edge energy efficiency

  17. Additive Manufacturing Technology Assessment

    Energy Savers [EERE]

    of Energy Additive Manufacturing Meets the Critical Materials Shortage Additive Manufacturing Meets the Critical Materials Shortage April 9, 2014 - 11:15am Addthis Green light reflection from a low-oxygen environment, 3D-printer laser deposition of metal powder alloys. | Photo courtesy of Critical Materials Institute, Ames Laboratory Green light reflection from a low-oxygen environment, 3D-printer laser deposition of metal powder alloys. | Photo courtesy of Critical Materials Institute, Ames

  18. Innovative Manufacturing Initiative Project Selections

    Broader source: Energy.gov [DOE]

    The Department announced nearly $23 million for 12 projects across the country to advance technologies aimed at helping American manufacturers dramatically increase the energy efficiency of their manufacturing facilities, lower costs, and develop new manufacturing technologies.

  19. EA-319-A Fortis Energy Marketing & Trading GP (BNP Paribas Energy Trading

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    GP) | Department of Energy -A Fortis Energy Marketing & Trading GP (BNP Paribas Energy Trading GP) EA-319-A Fortis Energy Marketing & Trading GP (BNP Paribas Energy Trading GP) Order authorizing Fortis Energy Marketing & Trading GP (BNP Paribas Energy Trading GP) to export electric energy to Canada PDF icon EA-319-A Fortis Energy Marketing & Trading GP (BNP Paribas Energy Trading GP) More Documents & Publications EA-319 Fortis Energy Marketing & Trading GP Listing of

  20. Laser Manufacturing | GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Home > Impact > Advanced Laser Manufacturing Tools Deliver Higher Performance Click to ... Advanced Laser Manufacturing Tools Deliver Higher Performance In a research lab looking ...

  1. The Clean Energy Manufacturing Initiative

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    THE OPPORTUNITY OF CLEAN ENERGY MANUFACTURING By 2030, the global market for new energy ... and domestic energy resources in manufacturing represents important opportunities for ...

  2. Innovative Manufacturing Initiative Recognition Day

    Broader source: Energy.gov [DOE]

    The Innovative Manufacturing Initiative (IMI) Recognition Day (held in Washington, DC on June 20, 2012) showcased IMI projects selected by the Energy Department to help American manufacturers...

  3. Manufacturing Consumption of Energy 1994

    U.S. Energy Information Administration (EIA) Indexed Site

    (MECS) > MECS 1994 Combined Consumption and Fuel Switching Manufacturing Energy Consumption Survey 1994 (Combined Consumption and Fuel Switching) Manufacturing Energy Consumption...

  4. Advanced Materials Manufacturing (AMM) Session

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Advanced Manufacturing Office (AMO) manufacturing.energy.gov 2 WELCOME & THANK YOU from your friendly support staff: Eric Miller, David Forrest, Fred Crowson, Jessica Savell... ...

  5. Innovative Manufacturing Initiative Recognition Day, Advanced...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications Innovative Manufacturing Initiative Recognition Day Advanced Manufacturing Office Overview Unlocking the Potential of Additive Manufacturing in the ...

  6. Energy Prices, Power, and Trade

    U.S. Energy Information Administration (EIA) Indexed Site

    Energy Prices, Power, and Trade for The Energy Council March 5, 2016 | Washington, D.C. by Adam Sieminski, Administrator U.S. Energy Information Administration Energy Markets Update 2 The Energy Council | Energy Prices, Power, and Trade March 5, 2016 $/b Continued robust supply and increasingly weak economic demand continue to pressure crude prices downward Source: EIA, Bloomberg 3 The Energy Council | Energy Prices, Power, and Trade March 5, 2016 $/MMbtu billion cubic feet Resilient production

  7. Career Map: Trade Worker | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Trade Worker Career Map: Trade Worker A trade worker inside a large wind component. Trade Worker Position Title Trade Worker Alternate Title(s) Iron Worker, Rigger, Rodbuster, Cement Mason, Crane Operator, Electrician Education & Training Level Bachelor's degree generally not expected. Some training preferred. Electricians require formal training. Education & Training Level Description Trade workers often learn informally on the job. Other positions may learn their trade through a formal

  8. Mark D. Mitchell | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    D. Mitchell About Us Mark D. Mitchell - Communications Support Contractor to ARPA-E Mark Mitchell is a Communications Support Contractor to ARPA-E. Most Recent ARPA-E Celebrates Five Years of Changing What's Possible April 28 Energy Innovators to Convene for 2014 ARPA-E Summit February 20 Interview with ARPA-E: The Future of Semiconductors February

  9. RANDOM PULSE GENERATOR PRODUCING FIDUCIAL MARKS

    DOE Patents [OSTI]

    Nielsen, W.F.

    1960-02-01

    The apparatus for automatically applying a fiducial marking, having a nonrepetitive pattern, to a plurality of simultaneously made records comprises, in series, a bypass filter, a trigger circuit, and a pulse generator, with printing means connected to and controlled by the pulse generator for simultaneously making the visible fiducial marks on a plurality of simultaneously produced records.

  10. Manufacturing Laboratory (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2011-10-01

    This fact sheet describes the purpose, lab specifications, applications scenarios, and information on how to partner with NREL's Manufacturing Laboratory at the Energy Systems Integration Facility. The Manufacturing Laboratory at NREL's Energy Systems Integration Facility (ESIF) focuses on developing methods and technologies that will assist manufacturers of hydrogen and fuel cell technologies, as well as other renewable energy technologies, to scale up their manufacturing capabilities to volumes that meet DOE and industry targets. Specifically, the manufacturing activity is currently focused on developing and validating quality control techniques to assist manufacturers of low temperature and high temperature fuel cells in the transition from low to high volume production methods for cells and stacks. Capabilities include initial proof-of-concept studies through prototype system development and in-line validation. Existing diagnostic capabilities address a wide range of materials, including polymer films, carbon and catalyst coatings, carbon fiber papers and wovens, and multi-layer assemblies of these materials, as well as ceramic-based materials in pre- or post-fired forms. Work leading to the development of non-contact, non-destructive techniques to measure critical dimensional and functional properties of fuel cell and other materials, and validation of those techniques on the continuous processing line. This work will be supported by materials provided by our partners. Looking forward, the equipment in the laboratory is set up to be modified and extended to provide processing capabilities such as coating, casting, and deposition of functional layers, as well as associated processes such as drying or curing. In addition, continuous processes are used for components of organic and thin film photovoltaics (PV) as well as battery technologies, so synergies with these important areas will be explored.

  11. Advanced Manufacture of Reflectors

    Broader source: Energy.gov [DOE]

    The Advance Manufacture of Reflectors fact sheet describes a SunShot Initiative project being conducted research team led by the University of Arizona, which is working to develop a novel method for shaping float glass. The technique developed by this research team can drastically reduce the time required for the shaping step. By enabling mass production of solar concentrating mirrors at high speed, this project should lead to improved performance and as much as a 40% reduction in manufacturing costs for reflectors made in very high volume.

  12. Energy Department Helps Manufacturers of Small and Mid-Size Wind Turbines

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Meet Certification Requirements | Department of Energy Helps Manufacturers of Small and Mid-Size Wind Turbines Meet Certification Requirements Energy Department Helps Manufacturers of Small and Mid-Size Wind Turbines Meet Certification Requirements October 1, 2015 - 1:04pm Addthis Energy Department Helps Manufacturers of Small and Mid-Size Wind Turbines Meet Certification Requirements Mark Higgins Operations Supervisor, Wind & Water Power Technologies Office On October 1, the Energy

  13. Manufacturing Innovation in the DOE

    Energy Savers [EERE]

    October 2012 | Department of Energy Definitions and Assumptions, October 2012 Manufacturing Energy and Carbon Footprint Definitions and Assumptions, October 2012 PDF icon footprints_assumptions_definitions_2012.pdf More Documents & Publications Understanding Manufacturing Energy and Carbon Footprints, October 2012 2010 Manufacturing Energy and Carbon Footprints: Definitions and Assumptions U.S. Manufacturing Energy Use and Greenhouse Gas Emissions Analysis

    References Manufacturing

  14. Drug development and manufacturing

    DOE Patents [OSTI]

    Warner, Benjamin P.; McCleskey, T. Mark; Burrell, Anthony K.

    2015-10-13

    X-ray fluorescence (XRF) spectrometry has been used for detecting binding events and measuring binding selectivities between chemicals and receptors. XRF may also be used for estimating the therapeutic index of a chemical, for estimating the binding selectivity of a chemical versus chemical analogs, for measuring post-translational modifications of proteins, and for drug manufacturing.

  15. Mark R Fahey | Argonne Leadership Computing Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    R Fahey Director of Operations Mark Fahey Argonne National Laboratory 9700 S. Cass Avenue Bldg. 240 / Rm. 2120 Argonne, IL 60439 630-252-1932 mfahey@anl.gov

  16. SolidMarks | Open Energy Information

    Open Energy Info (EERE)

    Product: German project developer found by IdeemaSun and MAGE Solar to develop solar parks across Europe. References: SolidMarks1 This article is a stub. You can help OpenEI...

  17. Trading Emissions PLC | Open Energy Information

    Open Energy Info (EERE)

    Trading Emissions PLC Jump to: navigation, search Name: Trading Emissions PLC Place: London, United Kingdom Zip: EC2N 4AW Product: Trading Emissions PLC is an investment fund...

  18. C Trade Ltd | Open Energy Information

    Open Energy Info (EERE)

    Trade Ltd Jump to: navigation, search Name: C Trade Ltd Place: Tuscon, Arizona Zip: 85718 3223 Sector: Carbon, Renewable Energy Product: C Trade is a carbon management company with...

  19. Clean Energy Manufacturing Initiative Midwest Regional Summit...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Breakout Session Summary More Documents & Publications Fiber Reinforced Polymer Composite Manufacturing Workshop Multimaterial Joining Workshop Manufacturing ...

  20. Eiko Trading Corporation | Open Energy Information

    Open Energy Info (EERE)

    Trading Corporation Jump to: navigation, search Name: Eiko Trading Corporation Place: Japan Sector: Solar Product: Eiko develops solar pv projects in Japan and is expected to...

  1. International Trade of Biofuels (Brochure), Energy Analysis,...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and trade of biofuels have increased to meet global demand for renewable fuels. Ethanol and biodiesel contribute much of this trade because they are the most established...

  2. Differences between nonprecipitating tropical and trade wind...

    Office of Scientific and Technical Information (OSTI)

    and trade wind marine shallow cumuli This content will become publicly available on November 13, 2016 Title: Differences between nonprecipitating tropical and trade wind marine ...

  3. Steinbeis Technology Transfer Centre for Emissions Trading |...

    Open Energy Info (EERE)

    Steinbeis Technology Transfer Centre for Emissions Trading Jump to: navigation, search Name: Steinbeis Technology Transfer Centre for Emissions Trading Place: Augsburg, Bavaria,...

  4. Hydrogen Delivery Infrastructure Analysis, Options and Trade...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Analysis, Options and Trade-offs, Transition and Long-term Hydrogen Delivery Infrastructure Analysis, Options and Trade-offs, Transition and Long-term Presentation on Hydrogen ...

  5. The Advanced Manufacturing Partnership and the Advanced Manufacturing...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    engineering and mathematics (STEM) education ... manufacturing from university spinouts & licensing * ... * High school teaching and learning models must be adapted ...

  6. National Electrical Manufacturers Association

    Energy Savers [EERE]

    July 24, 2014 VIA EMAIL TO: Regulatory.Review@hq.doe.gov Steven Croley, General Counsel Office of the General Counsel U.S. Department of Energy 1000 Independence Avenue SW., Washington, DC 20585 NEMA Comments on DOE Reducing Regulatory Burden RFI 79 Fed.Reg. 28518 (July 3, 2014) Dear Mr. Croley, The National Electrical Manufacturers Association (NEMA) thanks you for the opportunity to provide comments on the Department of Energy's efforts to make its regulatory program more effective and less

  7. Manufactured Homes Tool

    Energy Science and Technology Software Center (OSTI)

    2005-03-09

    The MH Tool software is designed to evaluate existing and new manufactured homes for structural adequacy in high winds. Users define design elements of a manufactured home and then select the hazard(s) for analysis. MH Tool then calculates and reports structural analysis results for the specified design and hazard Method of Solution: Design engineers input information (geometries, materials, etc.) describing the structure of a manufactured home, from which the software automatically creates a mathematical model.more » Windows, doors, and interior walls can be added to the initial design. HUD Code loads (wind, snow loads, interior live loads, etc.) are automatically applied. A finite element analysis is automatically performed using a third party solver to find forces and stresses throughout the structure. The designer may then employ components of strength (and cost) most appropriate for the loads that must be carried at each location, and then re-run the analysis for verification. If forces and stresses are still within tolerable limits (such as the HUD requirements), construction costs would be reduced without sacrificing quality.« less

  8. Fuel Oil Use in Manufacturing

    U.S. Energy Information Administration (EIA) Indexed Site

    logo Return to: Manufacturing Home Page Fuel Oil Facts Oil Price Effect Fuel Switching Actual Fuel Switching Storage Capacity Fuel Oil Use in Manufacturing Why Look at Fuel Oil?...

  9. Additive Manufacturing for Fuel Cells

    Broader source: Energy.gov [DOE]

    Blake Marshall, AMO's lead for Additive Manufacturing Technologies, will provide an overview of current R&D activities in additive manufacturing and its application to fuel cell prototyping and...

  10. Laser Manufacturing | GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Laser Manufacturing at GE Global Research Click to email this to a friend (Opens in new ... Laser Manufacturing at GE Global Research Learn how laser sintering, an additive laser ...

  11. Energy 101: Clean Energy Manufacturing

    SciTech Connect (OSTI)

    2015-07-09

    Most of us have a basic understanding of manufacturing. It's how we convert raw materials, components, and parts into finished goods that meet our essential needs and make our lives easier. But what about clean energy manufacturing? Clean energy and advanced manufacturing have the potential to rejuvenate the U.S. manufacturing industry and open pathways to increased American competitiveness. Watch this video to learn more about this exciting movement and to see some of these innovations in action.

  12. NREL: Energy Analysis - Manufacturing Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Recent Publications "Economic Measurements of Polysilicon for the Photovoltaic Industry: Market Competition and Manufacturing Competitiveness" IEEE Journal of Photovoltaics Supply Chain and Blade Manufacturing Considerations in the Global Wind Industry Economic Development Impact of 1,000 MW of Wind Energy in Texas Manufacturing Analysis With world-class manufacturing analysis capabilities, NREL analyzes clean energy industry trends; cost, price, and performance trends; market and

  13. ITP Nanomanufacturing: Nanomanufacturing Portfolio: Manufacturing...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Portfolio: Manufacturing Processes and Applications to Accelerate Commercial Use of Nanomaterials, January 2011 ITP Nanomanufacturing: Nanomanufacturing Portfolio: ...

  14. Energy 101: Clean Energy Manufacturing

    Broader source: Energy.gov [DOE]

    Most of us have a basic understanding of manufacturing. It's how we convert raw materials, components, and parts into finished goods that meet our essential needs and make our lives easier. But what about clean energy manufacturing? Clean energy and advanced manufacturing have the potential to rejuvenate the U.S. manufacturing industry and open pathways to increased American competitiveness. Watch this video to learn more about this exciting movement and to see some of these innovations in action.

  15. Revolutionizing Manufacturing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Engineering, and Mathematics -- education outreach at the Energy Department's ... National Network for Manufacturing Innovation pilot announcement. | Photo courtesy of ...

  16. Out of bounds additive manufacturing

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Holshouser, Chris; Newell, Clint; Palas, Sid; Love, Lonnie J.; Kunc, Vlastimil; Lind, Randall F.; Lloyd, Peter D.; Rowe, John C.; Blue, Craig A.; Duty, Chad E.; et al

    2013-03-01

    Lockheed Martin and Oak Ridge National Laboratory are working on an additive manufacturing system capable of manufacturing components measured not in terms of inches or feet, but multiple yards in all dimensions with the potential to manufacture parts that are completely unbounded in size.

  17. Out of Bounds Additive Manufacturing

    SciTech Connect (OSTI)

    Holshouser, Chris [Lockheed Martin Corporation; Newell, Clint [Lockheed Martin Corporation; Palas, Sid [Lockheed Martin Corporation; Love, Lonnie J [ORNL; Kunc, Vlastimil [ORNL; Lind, Randall F [ORNL; Lloyd, Peter D [ORNL; Rowe, John C [ORNL; Blue, Craig A [ORNL; Duty, Chad E [ORNL; Peter, William H [ORNL; Dehoff, Ryan R [ORNL

    2013-01-01

    Lockheed Martin and Oak Ridge National Laboratory are working on an additive manufacturing (AM) system capable of manufacturing components measured not in terms of inches or feet, but multiple yards in all dimensions with the potential to manufacture parts that are completely unbounded in size.

  18. MECS 2006 - All Manufacturing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    All Manufacturing MECS 2006 - All Manufacturing Manufacturing Energy and Carbon Footprint - Sector: All Manufacturing (NAICS 31-33) with Total Energy Input, October 2012 (MECS 2006) All available footprints and supporting documents Manufacturing Energy and Carbon Footprint PDF icon All Manufacturing (NAICS 31-33) More Documents & Publications All Manufacturing (2010 MECS) MECS 2006 - Alumina and Aluminum MECS 2006 - Cement

  19. Advanced Manufacturing Office (Formerly Industrial Technologies Program) |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Manufacturing Office (Formerly Industrial Technologies Program) Advanced Manufacturing Office (Formerly Industrial Technologies Program) Presented at the NREL Hydrogen and Fuel Cell Manufacturing R&D Workshop in Washington, DC, August 11-12, 2011. PDF icon DOE's Advanced Manufacturing Office More Documents & Publications Innovative Manufacturing Initiative Recognition Day Manufacturing Demonstration Facilities Workshop Agenda, March 2012 Advanced Manufacturing

  20. All Manufacturing (2010 MECS) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    All Manufacturing (2010 MECS) All Manufacturing (2010 MECS) Manufacturing Energy and Carbon Footprint for All Manufacturing Sector (NAICS 31-33) Energy use data source: 2010 EIA MECS (with adjustments) Footprint Last Revised: June 2015 View footprints for other sectors here. Manufacturing Energy and Carbon Footprint PDF icon All Manufacturing More Documents & Publications MECS 2006 - All Manufacturing Cement (2010 MECS) Chemicals (2010 MECS) Manufacturing Energy Sankey Diagrams Manufacturing

  1. Manufacturing Energy Consumption Survey (MECS) - Analysis & Projection...

    Gasoline and Diesel Fuel Update (EIA)

    Manufacturing Energy Consumption Data Show Large Reductions in Both Manufacturing Energy Use and the Energy Intensity of Manufacturing Activity between 2002 and 2010 MECS 2010 - ...

  2. Manufacturing Energy Consumption Survey (MECS) - Analysis & Projection...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    That increase in supply has in turn lowered the price of natural gas to manufacturers Manufacturing Energy Consumption Data Show Large Reductions in Both Manufacturing Energy Use ...

  3. clean energy manufacturing | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Clean Energy Manufacturing Initiative The Clean Energy Manufacturing Initiative is a strategic integration and commitment of manufacturing efforts across the DOE Office of Energy...

  4. Additive Manufacturing: Pursuing the Promise | Department of...

    Broader source: Energy.gov (indexed) [DOE]

    Fact sheet overviewing additive manufacturing techniques that are projected to exert a profound impact on manufacturing. Additive Manufacturing: Pursuing the Promise More Documents...

  5. FHP Manufacturing Company Geothermal | Open Energy Information

    Open Energy Info (EERE)

    FHP Manufacturing Company Geothermal Jump to: navigation, search Name: FHP Manufacturing Company: Geothermal Place: Florida Sector: Geothermal energy Product: FHP Manufacturing...

  6. Teksun PV Manufacturing Inc | Open Energy Information

    Open Energy Info (EERE)

    Teksun PV Manufacturing Inc Jump to: navigation, search Logo: Teksun PV Manufacturing Inc Name: Teksun PV Manufacturing Inc Address: 401 Congress Ave Place: Austin, Texas Zip:...

  7. Secure Manufacturing | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Secure Manufacturing Secure Manufacturing The depth and breadth of Y-12's manufacturing capabilities and expertise enable Y-12 to address current and emerging national security...

  8. WORKSHOP: SUSTAINABILITY IN MANUFACTURING AGENDA AND OVERVIEW...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    WORKSHOP: SUSTAINABILITY IN MANUFACTURING AGENDA AND OVERVIEW WORKSHOP: SUSTAINABILITY IN MANUFACTURING AGENDA AND OVERVIEW PDF icon Sustainable Manufacturing Workshop Agenda.pdf ...

  9. Semantic Web Service Framework to Intelligent Distributed Manufacturing

    SciTech Connect (OSTI)

    Kulvatunyou, Boonserm

    2005-12-01

    As markets become unexpectedly turbulent with a shortened product life cycle and a power shift towards buyers, the need for methods to develop products, production facilities, and supporting software rapidly and cost-effectively is becoming urgent. The use of a loosely integrated virtual enterprise based framework holds the potential of surviving changing market needs. However, its success requires reliable and large-scale interoperation among trading partners via a semantic web of trading partners services whose properties, capabilities, and interfaces are encoded in an unambiguous as well as computer-understandable form. This paper demonstrates a promising approach to integration and interoperation between a design house and a manufacturer that may or may not have prior relationship by developing semantic web services for business and engineering transactions. To this end, detailed activity and information flow diagrams are developed, in which the two trading partners exchange messages and documents. The properties and capabilities of the manufacturer sites are defined using DARPA Agent Markup Language (DAML) ontology definition language. The prototype development of semantic webs shows that enterprises can interoperate widely in an unambiguous and autonomous manner. This contributes towards the realization of virtual enterprises at a low cost.

  10. NREL: Photovoltaics Research - Mark Campanelli, Ph.D.

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mark Campanelli, Ph.D. Postdoctoral Researcher 303-384-6469 Mark.Campanelli@nrel.gov Mark Campanelli graduated with a master's degree and a doctorate in mathematics from Montana...

  11. Mark R. Hahn of the Richland Operations Office presented 2014...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Mark R. Hahn of the Richland Operations Office presented 2014 Safety System Oversight Annual Award Mark R. Hahn of the Richland Operations Office presented 2014 Safety System ...

  12. Mark Richey Woodworking Wind Farm | Open Energy Information

    Open Energy Info (EERE)

    Mark Richey Woodworking Energy Purchaser Mark Richey Woodworking Location Newburyport MA Coordinates 42.80211, -70.880604 Show Map Loading map... "minzoom":false,"mappingse...

  13. Wind Manufacturing Facilities | Department of Energy

    Energy Savers [EERE]

    Manufacturing Facilities Wind Manufacturing Facilities Wind Manufacturing Facilities America's wind energy industry supports a growing domestic industrial base. Check out this map to find manufacturing facilities in your state

  14. Y-12 Construction hits one million-hour mark without a lost-time accident |

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Y-12 National Security Complex Construction hits one ... Y-12 Construction hits one million-hour mark without a lost-time accident Posted: August 30, 2012 - 5:30pm The B&W Y-12 Direct-Hire Construction team has worked one million hours, covering a 633-day period, without a lost-time injury. Some 285 people including building trade crafts, non-manual staff and escorts worked without a lost-time accident during this period. The Construction team's last lost workday was in September 2010. A

  15. Plumbing Manufacturer's Institute Ex Parte Communication Regarding...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Plumbing Manufacturer's Institute Ex Parte Communication Regarding Showerheads Plumbing Manufacturer's Institute Ex Parte Communication Regarding Showerheads Letter to Department ...

  16. INDUSTRIAL SCALE DEMONSTRATION OF SMART MANUFACTURING ACHIEVING...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    INDUSTRIAL SCALE DEMONSTRATION OF SMART MANUFACTURING ACHIEVING TRANSFORMATIONAL ENERGY PRODUCTIVITY GAINS INDUSTRIAL SCALE DEMONSTRATION OF SMART MANUFACTURING ACHIEVING ...

  17. Nakagawa Electric Machinery Manufacturer | Open Energy Information

    Open Energy Info (EERE)

    navigation, search Name: Nakagawa Electric Machinery Manufacturer Place: Saku, Nagano, Japan Product: A company engages in electrical equipment manufacture. Coordinates:...

  18. ITP Nanomanufacturing: Manufacturing of Surfaces with Nanoscale...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Manufacturing of Surfaces with Nanoscale and Microscale Features ITP Nanomanufacturing: Manufacturing of Surfaces with Nanoscale and Microscale Features PDF icon...

  19. Clean Energy Manufacturing Innovation Institute for Composites...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Clean Energy Manufacturing Innovation Institute for Composites Materials and Structures Clean Energy Manufacturing Innovation Institute for Composites Materials and Structures ...

  20. Advanced Battery Manufacturing Facilities and Equipment Program...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications Advanced Battery Manufacturing Facilities and Equipment Program Advanced Battery Manufacturing Facilities and Equipment Program Fact ...

  1. American Energy and Manufacturing Competitiveness Summit Introduction...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Addthis Description Introduction video for the American Energy and Manufacturing ... for the American Energy and Manufacturing Competetitiveness Summit Introduction video. ...

  2. Advanced Manufacturing Office (Formerly Industrial Technologies...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Manufacturing Office (Formerly Industrial Technologies Program) Advanced Manufacturing Office (Formerly Industrial Technologies Program) Presented at the NREL Hydrogen and Fuel ...

  3. Semiconductor Manufacturing International Corp SMIC | Open Energy...

    Open Energy Info (EERE)

    Manufacturing International Corp SMIC Jump to: navigation, search Name: Semiconductor Manufacturing International Corp (SMIC) Place: Shanghai, Shanghai Municipality, China Zip:...

  4. Identification marking by means of laser peening

    DOE Patents [OSTI]

    Hackel, Lloyd A.; Dane, C. Brent; Harris, Fritz

    2002-01-01

    The invention is a method and apparatus for marking components by inducing a shock wave on the surface that results in an indented (strained) layer and a residual compressive stress in the surface layer. One embodiment of the laser peenmarking system rapidly imprints, with single laser pulses, a complete identification code or three-dimensional pattern and leaves the surface in a state of deep residual compressive stress. A state of compressive stress in parts made of metal or other materials is highly desirable to make them resistant to fatigue failure and stress corrosion cracking. This process employs a laser peening system and beam spatial modulation hardware or imaging technology that can be setup to impress full three dimensional patterns into metal surfaces at the pulse rate of the laser, a rate that is at least an order of magnitude faster than competing marking technologies.

  5. Manufacturing consumption of energy 1994

    SciTech Connect (OSTI)

    1997-12-01

    This report provides estimates on energy consumption in the manufacturing sector of the U.S. economy based on data from the Manufacturing Energy Consumption Survey. The sample used in this report represented about 250,000 of the largest manufacturing establishments which account for approximately 98 percent of U.S. economic output from manufacturing, and an expected similar proportion of manufacturing energy use. The amount of energy use was collected for all operations of each establishment surveyed. Highlights of the report include profiles for the four major energy-consuming industries (petroleum refining, chemical, paper, and primary metal industries), and an analysis of the effects of changes in the natural gas and electricity markets on the manufacturing sector. Seven appendices are included to provide detailed background information. 10 figs., 51 tabs.

  6. Mr. Mark Jackson Aluminum Company of America

    Office of Legacy Management (LM)

    _ of Energy Washington, DC 20565 Mr. Mark Jackson Aluminum Company of America 100 Technical Drive Alcoa Center, Pennsylvania 15069-0001 Dear Mr. Jackson: At,the request of the U.S. Department of Energy and with the consent of your company, Oak Ridge National Laboratory performed a radiological survey of the former ALCOA Research Labo,ratory at 600 Freeport Road in New Kensington, Pennsylvania. Three copies of the radiological survey report are enclosed for your information and use. An additional

  7. Geothermal Heat Pumps are Scoring High Marks

    SciTech Connect (OSTI)

    2000-08-01

    Geothermal Energy Program Office of Geothermal and Wind Technologies Geothermal Heat Pumps are Scoring High Marks Geothermal heat pumps, one of the clean energy technology stars Geothermal heat pumps (GHPs) are one of the most cost-effective heating, cooling, and water heating systems available for both residential and commercial buildings. GHPs extract heat from the ground during the heating season and discharge waste heat to the ground during the cooling season. The U.S. Environmental Protecti

  8. clean energy manufacturing | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Clean Energy Manufacturing Initiative The Clean Energy Manufacturing Initiative is a strategic integration and commitment of manufacturing efforts across the DOE Office of Energy Efficiency & Renewable Energy's (EERE's) clean energy technology offices and Advanced Manufacturing Office, focusing on American competitiveness in clean energy manufacturing. Clean Energy Manufacturing Initiative: http://www1.eere.energy.gov/energymanufacturing

  9. Advanced Manufacturing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Advanced Manufacturing Advanced Manufacturing EERE leads a robust network of researchers and other partners to continually develop cost-effective energy-saving solutions that help make our country run better through increased efficiency — promoting better plants, manufacturing processes, and products; more efficient new homes and improved older homes; and other solutions to enhance the buildings in which we work, shop, and lead our everyday lives. EERE leads a robust network of researchers

  10. Transformational Manufacturing | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Transformational Manufacturing Argonne's new Advanced Battery Materials Synthesis and Manufacturing R&D Program focuses on scalable process R&D to produce advanced battery materials in sufficient quantity for industrial testing. The U.S. manufacturing industry consumes more than 30 quadrillion Btu of energy per year, directly employs about 12 million people and generates another 7 million jobs in related businesses. Argonne is working with industry to develop innovative and

  11. Manufacturing consumption of energy 1991

    SciTech Connect (OSTI)

    Not Available

    1994-12-01

    This report provides estimates on energy consumption in the manufacturing sector of the US economy. These estimates are based on data from the 1991 Manufacturing Energy Consumption Survey (MECS). This survey--administered by the Energy End Use and Integrated Statistics Division, Office of Energy Markets and End Use, Energy Information Administration (EIA)--is the most comprehensive source of national-level data on energy-related information for the manufacturing industries.

  12. NREL: Energy Systems Integration - Manufacturing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Manufacturing Manufacturing capabilities at NREL support the production of components for fuel cells and electrochemical cells and the development of methods and technologies that will assist manufacturers of hydrogen and fuel cell technologies, as well as other renewable energy technologies, to scale up their production to meet national goals. Fuel cells cleanly and efficiently convert hydrogen into electricity through an electrochemical process. Fuel cells offer promise in a wide range of

  13. Manufacturing Consumption of Energy 1994

    U.S. Energy Information Administration (EIA) Indexed Site

    Detailed Tables 28 Energy Information AdministrationManufacturing Consumption of Energy 1994 1. In previous MECS, the term "primary energy" was used to denote the "first use" of...

  14. Manufacturing Consumption of Energy 1994

    U.S. Energy Information Administration (EIA) Indexed Site

    energy data used in this report do not reflect adjustments for losses in electricity generation or transmission. 1 The manufacturing sector is composed of establishments classified...

  15. Manufacturing Spotlight: Boosting American Competitiveness

    Broader source: Energy.gov [DOE]

    Find out how the Energy Department is helping bring new clean energy technologies to the marketplace and make manufacturing processes more energy efficient.

  16. The Clean Energy Manufacturing Initiative

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... projects that reduce the cost and risk of commercializing new technologies or ... manufacturing, data management, and operation of complex energy and communication systems. ...

  17. Manufacturing Consumption of Energy 1994

    U.S. Energy Information Administration (EIA) Indexed Site

    the CM, the ASM contains two components. The first component is the mail portion, a probability sample of manufacturing establishments selected from the list of establishments...

  18. The Clean Energy Manufacturing Initiative

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    by ensuring critical feedback from the production phase to invention and discovery. Additive manufacturing is just one of several technologies advanced by the Energy...

  19. Manufacturing Consumption of Energy 1994

    U.S. Energy Information Administration (EIA) Indexed Site

    Natural Gas to Residual Fuel Oil, by Industry Group and Selected Industries, 1994 369 Energy Information AdministrationManufacturing Consumption of Energy 1994 SIC Residual...

  20. High Pressure Hydrogen Tank Manufacturing

    Broader source: Energy.gov [DOE]

    Presented at the NREL Hydrogen and Fuel Cell Manufacturing R&D Workshop in Washington, DC, August 11-12, 2011.

  1. Electrolyzer Manufacturing Progress and Challenges

    Broader source: Energy.gov [DOE]

    Presented at the NREL Hydrogen and Fuel Cell Manufacturing R&D Workshop in Washington, DC, August 11-12, 2011.

  2. Manufacturing Fuel Cell Manhattan Project

    Broader source: Energy.gov [DOE]

    Presented at the NREL Hydrogen and Fuel Cell Manufacturing R&D Workshop in Washington, DC, August 11-12, 2011.

  3. Presentation, Marking OUO Documents - June 2014 | Department of Energy

    Energy Savers [EERE]

    Presentation, Marking OUO Documents - June 2014 Presentation, Marking OUO Documents - June 2014 June 2014 This presentation is solely on how to mark documents containing OUO information. PDF icon Presentation, Marking OUO Documents - June 2014 More Documents & Publications Briefing, DOE's Official Use Only Program - June 2014 Briefing, For Persons With Access to UCNI - June 2014 Briefing, Reviewing Official's UCNI Training

  4. EA-365 Centre Land Trading Limited | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Centre Land Trading Limited EA-365 Centre Land Trading Limited Order Authorizing Centre Land Trading Limited to export electric energy to Canada PDF icon EA-365 Centre Land ...

  5. EA-278 Direct Commodities Trading Inc | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Direct Commodities Trading Inc EA-278 Direct Commodities Trading Inc Order authorizing Direct Commodities Trading Inc to export electric energy to Canada. PDF icon OE-278 Direct ...

  6. EA-191-C Sempra Energy Trading Corporation | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    C Sempra Energy Trading Corporation EA-191-C Sempra Energy Trading Corporation Order authorizing Sempra Energy Trading Corporation to export electric energy to Canada. PDF icon ...

  7. EA-319 Fortis Energy Marketing & Trading GP | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fortis Energy Marketing & Trading GP EA-319 Fortis Energy Marketing & Trading GP Order authorizing Fortis Energy Marketing & Trading GP to export electric energy to Canada PDF ...

  8. EA-223-A CMS Marketing, Services and Trading Company | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    -A CMS Marketing, Services and Trading Company EA-223-A CMS Marketing, Services and Trading Company Order authorizing CMS Marketing, Services and Trading Company to export electric ...

  9. EA-223 CMS Marketing, Services and Trading Company | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    3 CMS Marketing, Services and Trading Company EA-223 CMS Marketing, Services and Trading Company Order authorizing CMS Marketing, Services and Trading Company to export electric ...

  10. EA-191-B Sempra Energy Trading Corporation | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    B Sempra Energy Trading Corporation EA-191-B Sempra Energy Trading Corporation Order authorizing Sempra Energy Trading Corporation to export electric energy to Canada. PDF icon ...

  11. EA-191 Sempra Energy Trading Corporation | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Sempra Energy Trading Corporation EA-191 Sempra Energy Trading Corporation Order authorizing Sempra Energy Trading Corporation to export electric energy to Canada. PDF icon EA-191 ...

  12. EA-191-D Sempra Energy Trading Corporation | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    D Sempra Energy Trading Corporation EA-191-D Sempra Energy Trading Corporation Order authorizing Sempra Energy Trading Corporation to export electric energy to Canada. PDF icon ...

  13. EA-191-A Sempra Energy Trading Corporation | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    -A Sempra Energy Trading Corporation EA-191-A Sempra Energy Trading Corporation Order authorizing Sempra Energy Trading Corporation to export electric energy to Canada. PDF icon ...

  14. Beijing EEDT Technology Trade Co Ltd | Open Energy Information

    Open Energy Info (EERE)

    EEDT Technology Trade Co Ltd Jump to: navigation, search Name: Beijing EEDT Technology & Trade Co Ltd Place: Beijing, China Sector: Carbon Product: Beijing EEDT Technology & Trade...

  15. SBIR and Global Trade Summit Presentation | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SBIR and Global Trade Summit Presentation SBIR and Global Trade Summit Presentation Presentation from the July 26, 2012 trade summit in Uncasville, Connecticut, presented by the ...

  16. EA-176 Sempra Energy Trading Corporation | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    EA-176 Sempra Energy Trading Corporation Order authorizing Sempra Energy Trading Corporation to export electric energy to Mexico. PDF icon EA-176 Sempra Energy Trading Corporation ...

  17. EA-176-A Sempra Energy Trading Corporation | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    EA-176-A Sempra Energy Trading Corporation Order authorizing Sempra Energy Trading Corporation to export electric energy to Mexico. PDF icon EA-176-A Sempra Energy Trading ...

  18. Green Hercules Trading Ltd | Open Energy Information

    Open Energy Info (EERE)

    Hercules Trading Ltd Jump to: navigation, search Name: Green Hercules Trading Ltd. Place: London, Greater London, United Kingdom Zip: EC2V 8BB Sector: Carbon Product: London-based...

  19. Biodiesel Energy Trading Limited | Open Energy Information

    Open Energy Info (EERE)

    Limited Jump to: navigation, search Name: Biodiesel Energy Trading Limited Place: London, United Kingdom Zip: W1J 8DY Product: London-based company focused on trading of biodiesel....

  20. Cinergy Capital & Trading, Inc | Open Energy Information

    Open Energy Info (EERE)

    Cinergy Capital & Trading, Inc Jump to: navigation, search Name: Cinergy Capital & Trading, Inc Place: Indiana Phone Number: (704) 382-3747 or (513) 287-2226 or (317) 838-1338...

  1. Emissions trading: principles and practice. 2nd

    SciTech Connect (OSTI)

    Tietenberg, T.H.

    2006-02-15

    The author demonstrates how emissions trading became an attractive alternative to command-and-control policies that would have required the EPA to disallow the opening of new plants in the middle of the recession-burdened 1970s. His examination of the evolution of this system includes, among other applications, the largest multinational trading system ever conceived, the European Union's Greenhouse Gas Emission Trading Scheme (EUETG), and the use of emissions trading in the Kyoto Protocol.

  2. International Bioenergy Trade | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    International Bioenergy Trade International Bioenergy Trade Chris Wright, INL, presentation at the December 5, 2012, Biomass Program-hosted International Webinar on international bioenergy trade. PDF icon wright_2012_webinar.pdf More Documents & Publications 2015 Peer Review Presentations-Biochemical Conversion 2015 Peer Review Report 2013 Peer Review Presentations-Feedstock Supply and Logistics

  3. Advanced Manufacture of Reflectors

    SciTech Connect (OSTI)

    Angel, Roger

    2014-12-17

    The main project objective has been to develop an advanced gravity sag method for molding large glass solar reflectors with either line or point focus, and with long or short focal length. The method involves taking standard sized squares of glass, 1.65 m x 1.65 m, and shaping them by gravity sag into precision steel molds. The method is designed for high volume manufacture when incorporated into a production line with separate pre-heating and cooling. The performance objectives for the self-supporting glass mirrors made by this project include mirror optical accuracy of 2 mrad root mean square (RMS), requiring surface slope errors <1 mrad rms, a target not met by current production of solar reflectors. Our objective also included development of new methods for rapidly shaping glass mirrors and coating them for higher reflectivity and soil resistance. Reflectivity of 95% for a glass mirror with anti-soil coating was targeted, compared to the present ~94% with no anti-soil coating. Our mirror cost objective is ~$20/m2 in 2020, a significant reduction compared to the present ~$35/m2 for solar trough mirrors produced for trough solar plants. During the first year a custom batch furnace was built to develop the method with high power radiative heating to simulate transfer of glass into a hot slumping zone in a production line. To preserve the original high polish of the float glass on both front and back surfaces, as required for a second surface mirror, the mold surface is machined to the required shape as grooves which intersect the glass at cusps, reducing the mold contact area to significantly less than 1%. The mold surface is gold-plated to reflect thermal radiation. Optical metrology of glass replicas made with the system has been carried out with a novel, custom-built test system. This test provides collimated, vertically-oriented parallel beams from a linear array of co-aligned lasers translated in a perpendicular direction across the reflector. Deviations of each reflected beam from the paraboloid focus give a direct measure of surface slope error. Key findings • A gravity sag method for large (2.5 m2) second surface glass solar reflectors has been developed and demonstrated to a uniquely high level of accuracy. Mirror surface slope accuracy of 0.65 mrad in one dimension, 0.85 mrad in 2 dimensions (point focus) has been demonstrated by commercial partner REhnu using this process. This accuracy exceeds by a factor of two current solar reflector accuracy. Our replicas meet the Sunshot accuracy objective of 2 mrad optical, which requires better than 1 mrad rms slope error. • Point-focus as well as line-focus mirrors have been demonstrated at 1.65 m x 1.65 m square – a unique capability. • The new process using simple molds is economical. The molds for the 1.65 m square reflectors are bent and machined steel plates on a counter-weighted flotation support. To minimize thermal coupling by radiative heat transfer, the mold surface is grooved and gilded. The molds are simple to manufacture, and have minimal thermal stresses and distortion in use. Lapping and bending techniques have been developed to obtain better than 1 mrad rms surface mold accuracy. Float glass is sagged into the molds by rapid radiative heating, using a custom high power (350 kW) furnace. The method of manufacture is well suited for small as well as large volume production, and as it requires little capital investment and no high technology, it could be used anywhere in the world to make solar concentrating reflectors. • A novel slope metrology method for full 1.65 aperture has been demonstrated, with 25 mm resolution across the face of the replicas. The method is null and therefore inherently accurate: it can easily be reproduced without high-tech equipment and does not need sophisticated calibration. We find by cross calibration with reference trough reflectors from RioGlass that our null-test laser system yields a measurement accuracy better than 0.4 mrad rms slope error. Our system is inexpensive and could have broad application for test and alignment of trough or dish reflectors. • Ten full size (2.5 m2) cylindrically curved reflectors, molded in 950 seconds and measured with the laser test facility, show shape repeatability to 0.5 mrad rms. These replicas met the Phase I Go/No-Go targets for speed (1000 sec), accuracy (< 5 mrad) and reproducibility (< 2 mrad). • Our research and tests show that the hoped-for improvements in mirror reflectivity achievable with titania antisoil coatings are not very effective in dry climates and are therefore unlikely to be economically worthwhile, and that glass with iron in the Fe+3 state to achieve very low absorption cannot be made economically by the float process.

  4. EA-211-A DTE Energy Trading, Inc | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    A DTE Energy Trading, Inc EA-211-A DTE Energy Trading, Inc Order authorizing DTE Energy Trading, Inc to export electric energy to Canada. PDF icon EA-211-A DTE Energy Trading, Inc ...

  5. EA-211 DTE Energy Trading, Inc | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    DTE Energy Trading, Inc EA-211 DTE Energy Trading, Inc Order authorizing DTE Energy Trading, Inc to export electric energy to Canada. PDF icon EA-211 DTE Energy Trading, Inc More ...

  6. EA-211-B DTE Energy Trading, Inc | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    B DTE Energy Trading, Inc EA-211-B DTE Energy Trading, Inc Order authorizing DTE Energy Trading, Inc to export electric energy to Canada. PDF icon EA-211-B DTE Energy Trading, Inc ...

  7. Manufacturers' View on Benchmarking and Disclosure

    U.S. Energy Information Administration (EIA) Indexed Site

    Association of Electrical and Medical Imaging Equipment Manufacturers Manufacturing Solutions for Energy Efficiency in Buildings Patrick Hughes Policy Director, High Performance Buildings National Electrical Manufacturers Association The Association of Electrical and Medical Imaging Equipment Manufacturers What is NEMA? The Association of Electrical Equipment and Medical Imaging Manufacturers Which policies encourage energy efficiency in buildings? Energy Savings Performance Contracts Tax

  8. Manufacturing serendipity: Chicago Innovation Exchange enhancing regional

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Association of Electrical and Medical Imaging Equipment Manufacturers Manufacturing Solutions for Energy Efficiency in Buildings Patrick Hughes Policy Director, High Performance Buildings National Electrical Manufacturers Association The Association of Electrical and Medical Imaging Equipment Manufacturers What is NEMA? The Association of Electrical Equipment and Medical Imaging Manufacturers Which policies encourage energy efficiency in buildings? Energy Savings Performance Contracts Tax

  9. Advanced Technology Vehicles Manufacturing Incentive Program | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Technology Vehicles Manufacturing Incentive Program Advanced Technology Vehicles Manufacturing Incentive Program A fact sheet detailling the advanced technology vehicles manufacturing incentive program. PDF icon Advanced Technology Vehicles Manufacturing Incentive Program More Documents & Publications Advanced Technology Vehicles Manufacturing Incentive Program MEMA: Comments MEMA: Letter

  10. Draft framework for watershed-based trading

    SciTech Connect (OSTI)

    1996-05-30

    Effluent trading is an innovative way for water quality agencies and community stakeholders to develop common-sense, cost-effective solutions for water quality problems in their watersheds. Trading can allow communities to grow and prosper while retaining their commitment to water quality. The bulk of this framework discusses effluent trading in watersheds. Remaining sections discuss transactions that, while not technically fulfilling the definition of `effluent` trade, do involve the exchange of valued water quality or other ecological improvements between partners responding to market initiatives. This document therefore includes activities such as trades within a facility (intra-plant trading) and wetland mitigation banking, effluent trading/watersheds/watershed management/water quality protection/water quality management.

  11. Manufacturing Consumption of Energy 1994

    U.S. Energy Information Administration (EIA) Indexed Site

    2(94) Distribution Category UC-950 Manufacturing Consumption of Energy 1994 December 1997 Energy Information Administration Office of Energy Markets and End Use U.S. Department of...

  12. Alternative Energy Manufacturing Tax Credit

    Broader source: Energy.gov [DOE]

    The Alternative Energy Manufacturing Tax Credit is a nonrefundable tax credit for up to 100% of new state tax revenues (including state, corporate, sales, and withholding taxes) over the life of a...

  13. 2014 Manufacturing Energy Consumption Survey

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    U S C E N S U S B U R E A U 2014 Manufacturing Energy Consumption Survey Sponsored by the Energy Information Administration U.S. Department of Energy Administered and Compiled by ...

  14. Manufacturing means jobs ? Mike Arms

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Manufacturing Means Jobs - Mike Arms Mike Arms and I usually meet and say hello at the East Tennessee Economic Council meetings each Friday morning at 7:30 a.m. This unique meeting...

  15. CFL Manufacturers: ENERGY STAR Letters

    Broader source: Energy.gov [DOE]

    DOE issued letters to 25 manufacturers of compact fluorescent lamps (CFLs) involving various models after PEARL Cycle 9 testing indicated that the models do not meet the ENERGY STAR specification and, therefore, are disqualified from the ENERGY STAR Program.

  16. Innovative Manufacturing Initiative Recognition Day

    Broader source: Energy.gov [DOE]

    The Innovative Manufacturing Initiative (IMI) Recognition Day (held in Washington, DC on June 20, 2012) showcased IMI projects selected by the Energy Department to help American manufacturers dramatically increase the energy efficiency of their operations and reduce costs. Each project will advance transformational technologies and materials that can benefit a broad cross-section of the domestic economy. This event created a platform for inter-agency and industry networking and also raised awareness among congressional staff and private investors.

  17. The President's Manufacturing Initiative | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Presentation prepared by Dale Hall for the Roadmap Workshop on Manufacturing R&D for the ... Manufacturing National Program Office Roadmap on Manufacturing R&D for the Hydrogen ...

  18. Advanced Manufacturing Office Overview | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Office Overview Advanced Manufacturing Office Overview PDF icon mw_rf_workshop_july2012.pdf More Documents & Publications Microwave and Radio Frequency Workshop Manufacturing Demonstration Facility Workshop Microwave (MW) and Radio Frequency (RF) as Enabling Technologies for Advanced Manufacturing

  19. EA-155 ProMark | Department of Energy

    Energy Savers [EERE]

    Order authorizing ProMark Energy, Inc to export electric energy to Canada. PDF icon EA-155 ProMark More Documents & Publications EA-196-A Minnesota Power, Sales EA-220-A NRG Power ...

  20. Mark Elless, Ph.D. | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Mark Elless, Ph.D. About Us Mark Elless, Ph.D. - Technology Manager, Bioenergy Technologies Office Most Recent Biofuels and Barbecue Chips: Small Business Develops Process to Create Versatile Chemicals May 16

  1. Security Policy, CMPC Marking Resource | Department of Energy

    Energy Savers [EERE]

    Security Policy, CMPC Marking Resource Security Policy, CMPC Marking Resource January 2015 Examples illustrate markings for matter that contains classified information. A strong and cohesive information security program is integral to national security. The U.S. Government requires certain information to be maintained in confidence to protect our citizens, democratic institutions, and activities within the international security community. Marking notifies holders of classified matter of the

  2. Summary, UCNI Document Markings - November 2011 | Department of Energy

    Energy Savers [EERE]

    Summary, UCNI Document Markings - November 2011 Summary, UCNI Document Markings - November 2011 November 2011 A brief summary on Marking UCNI Documents and Material. Once an UCNI Reviewing Official has determined that a document or material contains UCNI, the document or material must be marked to ensure its protection. First, though, it is important to understand what constitutes a document and material as defined in 10 CFR 1017.4. Document means the physical medium on or in which information

  3. 2014 Manufacturing Energy and Carbon Footprints: Scope

    Energy Savers [EERE]

    Scope The energy and carbon footprint analysis examines fifteen individual manufacturing sectors that together consume 95% of U.S. manufacturing primary energy consumption and ...

  4. Upcoming Clean Energy Manufacturing Initiative (CEMI) Southeast...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Upcoming Clean Energy Manufacturing Initiative (CEMI) Southeast Regional Summit on July 9 in Atlanta, GA Upcoming Clean Energy Manufacturing Initiative (CEMI) Southeast Regional ...

  5. Additive Manufacturing Meets the Critical Materials Shortage

    Broader source: Energy.gov [DOE]

    Find out how the Energy Department's Advanced Manufacturing Office is working to address potential shortages of critical materials through additive manufacturing, or 3D printing.

  6. Energy Intensity Indicators: Manufacturing Energy Intensity

    Broader source: Energy.gov [DOE]

    The manufacturing sector comprises 18 industry sectors, generally defined at the three-digit level of the North American Industrial Classification System (NAICS). The manufacturing energy data...

  7. Miraial formerly Kakizaki Manufacturing | Open Energy Information

    Open Energy Info (EERE)

    to: navigation, search Name: Miraial (formerly Kakizaki Manufacturing) Place: Tokyo, Japan Zip: 171-0021 Product: Manufacturer of wafer handling products and other components...

  8. Energy Department Invests in Innovative Manufacturing Technologies...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    in Innovative Manufacturing Technologies Energy Department Invests in Innovative Manufacturing Technologies June 13, 2012 - 12:00am Addthis The Energy Department announced on June...

  9. Manufacturing Institutes Exhibit American Innovation at Hannover...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Manufacturing Institutes Exhibit American Innovation at Hannover Messe Manufacturing Institutes Exhibit American Innovation at Hannover Messe April 25, 2016 - 4:30pm Addthis The ...

  10. Industrial Scale Demonstration of Smart Manufacturing Achieving...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    unit processes, smart manufacturing (SM) systems that ... A smart system that not only sought to recover waste heat, ... is based on current manufacturing and IT industry standards. ...

  11. Advanced Battery Manufacturing Facilities and Equipment Program...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications Advanced Battery Manufacturing Facilities and Equipment Program Advanced Battery Manufacturing Facilities and Equipment Program AVTA: 2010 Honda Civic ...

  12. American Wind Manufacturing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    American Wind Manufacturing Addthis 1 of 9 Nordex USA -- a global manufacturer of wind turbines -- delivered and installed turbine components for the Power County Wind...

  13. National Network for Manufacturing Innovation: A Preliminary...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Network for Manufacturing Innovation: A Preliminary Design National Network for Manufacturing Innovation: A Preliminary Design The Federal investment in the National Network for ...

  14. China Shandong Penglai Electric Power Equipment Manufacturing...

    Open Energy Info (EERE)

    Penglai Electric Power Equipment Manufacturing Jump to: navigation, search Name: China Shandong Penglai Electric Power Equipment Manufacturing Place: Penglai, Shandong Province,...

  15. National Electrical Manufacturers Association (NEMA) Response...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Electrical Manufacturers Association (NEMA) Response to Smart Grid RFI National Electrical Manufacturers Association (NEMA) Response to Smart Grid RFI The National Electrical ...

  16. Advanced Qualification of Additive Manufacturing Workshop

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Additive Manufacturing Workshop Poster Abstract Submission - deadline July 10, 2015 Advanced Qualification of Additive Manufacturing Materials using in situ sensors, diagnostics...

  17. FY 2008 Honeywell Federal Manufacturing & Technologies, LLC,...

    National Nuclear Security Administration (NNSA)

    FY 2008 Honeywell Federal Manufacturing & Technologies, LLC, PER Summary SUMMARY OF FY 2008 HONEYWELL FEDERAL MANUFACTURING & TECHNOLOGIES, LLC, AWARD FEE DETERMINATION Total ...

  18. FY 2010 Honeywell Federal Manufacturing & Technologies, LLC,...

    National Nuclear Security Administration (NNSA)

    FY 2010 Honeywell Federal Manufacturing & Technologies, LLC, PER Summary SUMMARY OF FY 2010 HONEYWELL FEDERAL MANUFACTURING & TECHNOLOGIES, LLC, AWARD FEE DETERMINATION Total ...

  19. FY 2009 Honeywell Federal Manufacturing & Technologies, LLC,...

    National Nuclear Security Administration (NNSA)

    FY 2009 Honeywell Federal Manufacturing & Technologies, LLC, PER Summary SUMMARY OF FY 2009 HONEYWELL FEDERAL MANUFACTURING & TECHNOLOGIES, LLC, AWARD FEE DETERMINATION Total ...

  20. FY 2006 Honeywell Federal Manufacturing & Technologies, LLC,...

    National Nuclear Security Administration (NNSA)

    FY 2006 Honeywell Federal Manufacturing & Technologies, LLC, PER Summary SUMMARY OF FY 2006 HONEYWELL FEDERAL MANUFACTURING & TECHNOLOGIES, LLC, AWARD FEE DETERMINATION Total ...

  1. FY 2007 Honeywell Federal Manufacturing & Technologies, LLC,...

    National Nuclear Security Administration (NNSA)

    FY 2007 Honeywell Federal Manufacturing & Technologies, LLC, PER Summary SUMMARY OF FY 2007 HONEYWELL FEDERAL MANUFACTURING & TECHNOLOGIES, LLC, AWARD FEE DETERMINATION Total ...

  2. FY 2011 Honeywell Federal Manufacturing & Technologies, LLC,...

    National Nuclear Security Administration (NNSA)

    FY 2011 Honeywell Federal Manufacturing & Technologies, LLC, PER Summary SUMMARY OF FY 2011 HONEYWELL FEDERAL MANUFACTURING & TECHNOLOGIES, LLC, AWARD FEE DETERMINATION Total ...

  3. Manufacturing Barriers to High Temperature PEM Commercialization...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Barriers to High Temperature PEM Commercialization Manufacturing Barriers to High Temperature PEM Commercialization Presented at the NREL Hydrogen and Fuel Cell Manufacturing R&D ...

  4. Manufacturing Demonstration Facilities Workshop Agenda, March...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Manufacturing Demonstration Facilities Workshop Marriott Springhill Suites O'Hare - Chicago, IL March 12, 2012 Objectives Introduce the manufacturing community to the U.S. DOE ...

  5. Understanding Manufacturing Energy and Carbon Footprints, October...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Documents & Publications Understanding the 2010 Manufacturing Energy and Carbon Footprints U.S. Manufacturing Energy Use and Greenhouse Gas Emissions Analysis MECS 2006 - Cement

  6. Oak Ridge Centers for Manufacturing Technology - Partnership...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Impact on the Semiconductor Industry, part 2 The Oak Ridge Centers for Manufacturing Technology in partnership with SEMATECH (Semiconductor Manufacturing TECHnology) had...

  7. Clean Energy Manufacturing Initiative Southeast Regional Summit...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Clean Energy Manufacturing Initiative Southeast Regional Summit Clean Energy Manufacturing Initiative Southeast Regional Summit July 9, 2015 8:30AM to 6:00PM EDT Renaissance...

  8. Batteries - Materials Processing and Manufacturing Breakout session

    Broader source: Energy.gov (indexed) [DOE]

    the Other Technical Areas Being Discussed * Li metal manufacturing * Variability in cell manufacturing -intrinsic reduction and aging differences in pack? * Understanding of...

  9. Processing and Manufacturing Equipment | Open Energy Information

    Open Energy Info (EERE)

    Processing and Manufacturing Equipment Jump to: navigation, search TODO: Add description List of Processing and Manufacturing Equipment Incentives Retrieved from "http:...

  10. Technologies Enabling Agile Manufacturing (TEAM) ? an ORCMT...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Technologies Enabling Agile Manufacturing (TEAM) - An ORCMT success story Technologies Enabling Agile Manufacturing (TEAM) was one of the larger programs to come from the...

  11. Bio Solutions Manufacturing Inc | Open Energy Information

    Open Energy Info (EERE)

    Solutions Manufacturing Inc Jump to: navigation, search Name: Bio Solutions Manufacturing Inc Place: Las Vegas, Nevada Zip: 89103 Product: Waste-to-energy bioremediation developer....

  12. DOE - Office of Legacy Management -- Manufacturing Laboratories...

    Office of Legacy Management (LM)

    Manufacturing Laboratories Inc - MA 0-04 FUSRAP Considered Sites Site: MANUFACTURING LABORATORIES, INC. (MA.0-04 ) Eliminated from further consideration under FUSRAP Designated...

  13. Chung Hsin Electric Machinery Manufacturing Corporation CHEM...

    Open Energy Info (EERE)

    Chung Hsin Electric Machinery Manufacturing Corporation CHEM Jump to: navigation, search Name: Chung Hsin Electric & Machinery Manufacturing Corporation (CHEM) Place: Taoyuan...

  14. Leitner Shriram Manufacturing Ltd | Open Energy Information

    Open Energy Info (EERE)

    Manufacturing Ltd Jump to: navigation, search Name: Leitner Shriram Manufacturing Ltd Place: Chennai, Tamil Nadu, India Zip: 600095 Sector: Wind energy Product: Chennai-based JV...

  15. advanced manufacturing office | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Advanced Manufacturing Office The U.S. Department of Energy (DOE) funds the research, development, and demonstration of highly efficient and innovative manufacturing technologies....

  16. Advanced Qualification of Additive Manufacturing Materials Workshop

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Advanced Qualification of Additive Manufacturing Materials Workshop Advanced Qualification of Additive Manufacturing Materials Workshop WHEN: Jul 20, 2015 8:30 AM - Jul 21, 2015...

  17. Aurora Photovoltaics Manufacturing | Open Energy Information

    Open Energy Info (EERE)

    Photovoltaics Manufacturing Jump to: navigation, search Name: Aurora Photovoltaics Manufacturing Place: Lawrenceville, New Jersey Zip: 8648 Sector: Solar Product: A subsidiary of...

  18. Industrial Activities at DOE: Efficiency, Manufacturing, Process...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PDF icon Industrial Activities at DOE: Efficiency, Manufacturing, Process, and Materials R&D More Documents & Publications Fiber Reinforced Polymer Composite Manufacturing Workshop ...

  19. Wind Energy & Manufacturing | Open Energy Information

    Open Energy Info (EERE)

    Wind Energy & Manufacturing Jump to: navigation, search Blades manufactured at Gamesa's factory in Ebensburg, Pennsylvania, will be delivered to wind farms across the United...

  20. Manufacturing Consumption of Energy 1991--Combined Consumption...

    U.S. Energy Information Administration (EIA) Indexed Site

    call 202-586-8800 for help. Return to Energy Information Administration Home Page. Home > Energy Users > Manufacturing > Consumption and Fuel Switching Manufacturing Consumption of...

  1. Stronger Manufacturers' Energy Efficiency Standards for Residential...

    Energy Savers [EERE]

    Stronger Manufacturers' Energy Efficiency Standards for Residential Air Conditioners Go Into Effect Today Stronger Manufacturers' Energy Efficiency Standards for Residential Air ...

  2. Clean Energy Manufacturing Initiative Events | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Initiative Events Clean Energy Manufacturing Initiative Events

  3. Worldwide Energy and Manufacturing USA Inc formerly Worldwide...

    Open Energy Info (EERE)

    and Manufacturing USA Inc formerly Worldwide Manufacturing USA Jump to: navigation, search Name: Worldwide Energy and Manufacturing USA Inc (formerly Worldwide Manufacturing USA)...

  4. Supply Chain and Blade Manufacturing Considerations in the Global Wind Industry (Presentation)

    SciTech Connect (OSTI)

    James, T.; Goodrich, A.

    2013-12-01

    This briefing provides an overview of supply chain developments in the global wind industry and a detailed assessment of blade manufacturing considerations for U.S. end-markets. The report discusses the international trade flows of wind power equipment, blade manufacturing and logistical costs, and qualitative issues that often influence factory location decisions. To help guide policy and research and development strategy decisions, this report offers a comprehensive perspective of both quantitative and qualitative factors that affect selected supply chain developments in the growing wind power industry.

  5. Congressional House Senate Request Marks Marks FOSSIL ENERGY R&D

    Energy Savers [EERE]

    3 FY 2013 FY 2013 ($ in thousands) Congressional House Senate Request Marks Marks FOSSIL ENERGY R&D Coal 275,869 384,294 301,622 Natural Gas Technologies 17,000 17,000 22,000 Unconventional Fossil Energy Technologies 0 25,000 5,000 Program Direction 115,753 115,753 120,000 Plant & Capital Equipment 13,294 13,294 13,294 Environmental Restoration 5,897 5,897 5,897 Special Recruitment Program 700 700 700 Subtotal, Fossil Energy R&D 428,513 561,938 468,513 Use of prior year balances

  6. Photovoltaic manufacturing technology, Phase 1

    SciTech Connect (OSTI)

    Not Available

    1992-10-01

    This report describes subcontracted research by the Chronar Corporation, prepared by Advanced Photovoltaic Systems, Inc. (APS) for Phase 1 of the Photovoltaic Manufacturing Technology Development project. Amorphous silicon is chosen as the PV technology that Chronar Corporation and APS believe offers the greatest potential for manufacturing improvements, which, in turn, will result in significant cost reductions and performance improvements in photovoltaic products. The APS Eureka'' facility was chosen as the manufacturing system that can offer the possibility of achieving these production enhancements. The relationship of the Eureka'' facility to Chronar's batch'' plants is discussed. Five key areas are also identified that could meet the objectives of manufacturing potential that could lead to improved performance, reduced manufacturing costs, and significantly increased production. The projected long-term potential benefits of these areas are discussed, as well as problems that may impede the achievement of the hoped-for developments. A significant number of the problems discussed are of a generic nature and could be of general interest to the industry. The final section of this document addresses the cost and time estimates for achieving the solutions to the problems discussed earlier. Emphasis is placed on the number, type, and cost of the human resources required for the project.

  7. Clean Tech Trade Alliance | Open Energy Information

    Open Energy Info (EERE)

    30351,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":"" Hide Map References: Clean Tech Trade Alliance Web Site1 This article is a stub. You can help...

  8. Multilateral, regional and bilateral energy trade governance

    SciTech Connect (OSTI)

    Leal-Arcas, Rafael; Grasso, Costantino; Rios, Juan Alemany )

    2014-12-01

    The current international energy trade governance system is fragmented and multi-layered. Streamlining it for greater legal cohesiveness and international political and economic cooperation would promote global energy security. The current article explores three levels of energy trade governance: multilateral, regional and bilateral. Most energy-rich countries are part of the multilateral trading system, which is institutionalized by the World Trade Organization (WTO). The article analyzes the multilateral energy trade governance system by focusing on the WTO and energy transportation issues. Regionally, the article focuses on five major regional agreements and their energy-related aspects and examines the various causes that explain the proliferation of regional trade agreements, their compatibility with WTO law, and then provides several examples of regional energy trade governance throughout the world. When it comes to bilateral energy trade governance, this article only addresses the European Union’s (EU) bilateral energy trade relations. The article explores ways in which gaps could be filled and overlaps eliminated whilst remaining true to the high-level normative framework, concentrating on those measures that would enhance EU energy security.

  9. Carbon Trade Ltd | Open Energy Information

    Open Energy Info (EERE)

    Ltd Jump to: navigation, search Name: Carbon Trade Ltd Place: Scotland, United Kingdom Zip: ML12 6HW Product: Scotland-based landfill gas project developer. References: Carbon...

  10. International Centre for Trade and Sustainable Development |...

    Open Energy Info (EERE)

    Development Jump to: navigation, search Name: International Centre for Trade and Sustainable Development Address: International Environment House 2 Chemin de Balexert 7-9...

  11. Metrology for Fuel Cell Manufacturing

    SciTech Connect (OSTI)

    Stocker, Michael; Stanfield, Eric

    2015-02-04

    The project was divided into three subprojects. The first subproject is Fuel Cell Manufacturing Variability and Its Impact on Performance. The objective was to determine if flow field channel dimensional variability has an impact on fuel cell performance. The second subproject is Non-contact Sensor Evaluation for Bipolar Plate Manufacturing Process Control and Smart Assembly of Fuel Cell Stacks. The objective was to enable cost reduction in the manufacture of fuel cell plates by providing a rapid non-contact measurement system for in-line process control. The third subproject is Optical Scatterfield Metrology for Online Catalyst Coating Inspection of PEM Soft Goods. The objective was to evaluate the suitability of Optical Scatterfield Microscopy as a viable measurement tool for in situ process control of catalyst coatings.

  12. Oak Ridge Manufacturing Demonstration Facility (MDF)

    Broader source: Energy.gov [DOE]

    The Manufacturing Demonstration Facility (MDF) is a collabora­tive manufacturing community that shares a common RD&D infrastructure. This shared infrastructure provides affordable access to advanced physical and virtual tools for rapidly demonstrating new manufacturing technologies and optimizing critical processes. Oak Ridge National Laboratory is home to AMO's MDF focused on Additive Manufacturing and Low-cost Carbon Fiber.

  13. Manufacturing Demonstration Facilities Workshop Agenda, March 2012

    Broader source: Energy.gov [DOE]

    Agenda for the Manufacturing Demonstration Facilities Workshop on March 12, 2012 outlining objectives and times

  14. Method for manufacturing glass frit

    DOE Patents [OSTI]

    Budrick, Ronald G.; King, Frank T.; Nolen, Jr., Robert L.; Solomon, David E.

    1977-01-01

    A method of manufacturing a glass frit for use in the manufacture of uniform glass microspheres to serve as containers for laser fusion fuel to be exposed to laser energy which includes the formation of a glass gel which is then dried, pulverized, and very accurately sized to particles in a range of, for example, 125 to 149 micrometers. The particles contain an occluded material such as urea which expands when heated. The sized particles are washed, dried, and subjected to heat to control the moisture content prior to being introduced into a system to form microspheres.

  15. Manufacturing Energy and Carbon Footprints (2006 MECS)

    Broader source: Energy.gov [DOE]

    Energy and Carbon Footprints provide a mapping of energy from supply to end use in manufacturing. They show us where energy is used and lost—and where greenhouse gases (GHGs) are emitted. Footprints are available below for 15 manufacturing sectors (representing 94% of all manufacturing energy use) and for U.S. manufacturing as a whole. Analysis of these footprints is also available in the U.S. Manufacturing Energy Use and Greenhouse Gas Emissions Analysis report.

  16. Manufacturing Success Stories | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Efficiency » Manufacturing Success Stories Manufacturing Success Stories RSS The Office of Energy Efficiency and Renewable Energy's (EERE) successes in developing technologies and processes for more efficient energy management systems create big opportunities for energy savings and new jobs in manufacturing. Explore EERE's manufacturing success stories below. November 17, 2015 Manufacturing Success Stories EERE Success Story-ORNL Unveils 3D-Printed Home and Vehicle with the Unique

  17. White House Announces Eighth Manufacturing Innovation Institute |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy White House Announces Eighth Manufacturing Innovation Institute White House Announces Eighth Manufacturing Innovation Institute April 6, 2016 - 4:49pm Addthis On Thursday, April 1, the White House announced a new institute which will focus on revolutionary fibers and textile manufacturing. This new institute is the eighth manufacturing hub to be awarded as part of the National Network for Manufacturing Innovation (NNMI). Collectively, the federal government's commitment

  18. Clean Energy Manufacturing Initiative | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Manufacturing Initiative Clean Energy Manufacturing Initiative Clean Energy Manufacturing Initiative Industrial Efficiency and Energy Productivity Video Clean Energy Manufacturing Initiative Industrial Efficiency and Energy Productivity Video Industrial efficiency and low-cost energy resources are key components to increasing U.S. energy productivity and makes the U.S. manufacturing sector more competitive. Companies find a competitive advantage in implementing efficiency technologies and

  19. Explore Careers in Manufacturing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Manufacturing Explore Careers in Manufacturing The Advanced Manufacturing Office (AMO) invests in public-private research and development partnerships and encourages a culture of continuous improvement in corporate energy management to bring about a transformation in U.S. manufacturing. The Advanced Manufacturing Office (AMO) invests in public-private research and development partnerships and encourages a culture of continuous improvement in corporate energy management to bring about a

  20. Next Generation Manufacturing Processes | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Research & Development Projects » Next Generation Manufacturing Processes Next Generation Manufacturing Processes New process technologies can rejuvenate U.S. manufacturing. Novel processing concepts can open pathways to double net energy productivity, enabling rapid manufacture of energy-efficient, high-quality products at competitive cost. Four process technology areas are expected to generate large energy, carbon, and economic benefits across the manufacturing sector. Click the areas

  1. Solar Manufacturing Technology | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technology to Market » Solar Manufacturing Technology Solar Manufacturing Technology The SunShot Solar Manufacturing Technology (SolarMat) program funds the development of innovative manufacturing technologies that can achieve a significant market impact in one to four years. Launched in September 2013, the SolarMat program is supporting five projects working in two topic areas: photovoltaics (PV) and concentrating solar power (CSP). Both topics focus on driving down the cost of manufacturing

  2. Heat treating of manufactured components

    DOE Patents [OSTI]

    Ripley, Edward B.

    2012-05-22

    An apparatus for heat treating manufactured components using microwave energy and microwave susceptor material is disclosed. The system typically includes an insulating vessel placed within a microwave applicator chamber. A moderating material is positioned inside the insulating vessel so that a substantial portion of the exterior surface of each component for heat treating is in contact with the moderating material.

  3. Solar Thermal Collector Manufacturing Activities

    Gasoline and Diesel Fuel Update (EIA)

    6 Number of companies expecting to introduce new solar new solar thermal collector products in 2010 Low-Temperature Collectors 4 Medium-Temperature Collectors 16 High-Temperature Collectors 11 Noncollector Components 12 Form EIA-63A, "Annual Solar Thermal Collector Manufacturers Survey." New Product Type Number of Companies Source: U.S. Energy Information Administration,

  4. Process for manufacturing multilayer capacitors

    DOE Patents [OSTI]

    Lauf, Robert J.; Holcombe, Cressie E.; Dykes, Norman L.

    1996-01-01

    The invention is directed to a method of manufacture of multilayer electrical components, especially capacitors, and components made by such a method. High capacitance dielectric materials and low cost metallizations layered with such dielectrics may be fabricated as multilayer electrical components by sintering the metallizations and the dielectrics during the fabrication process by application of microwave radiation.

  5. Process for manufacturing multilayer capacitors

    DOE Patents [OSTI]

    Lauf, R.J.; Holcombe, C.E.; Dykes, N.L.

    1996-01-02

    The invention is directed to a method of manufacture of multilayer electrical components, especially capacitors, and components made by such a method. High capacitance dielectric materials and low cost metallizations layered with such dielectrics may be fabricated as multilayer electrical components by sintering the metallizations and the dielectrics during the fabrication process by application of microwave radiation. 4 figs.

  6. Meeting Summary, Credit Trading Work Group

    SciTech Connect (OSTI)

    Kevin Bryan

    2000-12-07

    OAK-B135 Credit Trading Work Group Meeting Summary. The purpose of the meeting is to: (1) Provide an opportunity for NWCC Work Group Members, NWCC Members, and invited expert participants to hear an overview of the draft NWCC Credit Trading Report and to critically review and discuss the report's recommendations and principles. (2) Hear presentations from several perspectives of other experts on credit trading which provide: (a) a brief summary of credit trading activities they are involved in, and (b) critical responses to the NWCC draft report. (3) Identify how the report can be improved at the big picture level. Attempt to resolve issues or concerns if necessary. (4) Discuss the recommendations and credit trading principles in detail and attempt to reach consensus on these sections for presentation to the NWCC. (5) Discuss if any of the outreach and communication recommendations in the report should be conducted by the NWCC.

  7. Second Anniversary of Northeast Blackout Marked with Progress | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Anniversary of Northeast Blackout Marked with Progress Second Anniversary of Northeast Blackout Marked with Progress August 12, 2005 - 2:41pm Addthis Electric Reliability Standards Made Clearer and Enforceable WASHINGTON, DC - Secretary of Energy Samuel W. Bodman today marked the second anniversary of the Northeast blackout during which 50 million Americans lost electricity by highlighting important progress that has been made to make North American electricity grids more reliable.

  8. EA-319-A Fortis Energy Marketing & Trading GP (BNP Paribas Energy...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    -A Fortis Energy Marketing & Trading GP (BNP Paribas Energy Trading GP) EA-319-A Fortis Energy Marketing & Trading GP (BNP Paribas Energy Trading GP) Order authorizing Fortis ...

  9. Additive Manufacturing: Pursuing the Promise | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Additive Manufacturing: Pursuing the Promise Additive Manufacturing: Pursuing the Promise Fact sheet overviewing additive manufacturing techniques that are projected to exert a profound impact on manufacturing. PDF icon Additive Manufacturing: Pursuing the Promise More Documents & Publications QTR Webinar: Chapter 8 - Industry and Manufacturing WORKSHOP: SUSTAINABILITY IN MANUFACTURING, JANUARY 6-7 Unlocking the Potential of Additive Manufacturing in the Fuel Cells Industry

  10. Manipulative Virtual Tools for Tool Mark Characterization | The...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Manipulative Virtual Tools for Tool Mark Characterization FWPProject Description: The goal of this project is to develop a methodology whereby a three-dimensional (3-D) computer...

  11. Manipulative Virtual Tools for Tool Mark Characterization | The...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Manipulative Virtual Tools for Tool Mark Characterization DESCRIPTION: The goal of this project is to develop a methodology whereby a three-dimensional (3-D) computer simulation of...

  12. Written Statement of Mark Whitney Acting Assistant Secretary...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Mark Whitney Acting Assistant Secretary for Environmental Management United States Department of Energy Before the Subcommittee on Strategic Forces Committee on Armed Services ...

  13. Moab Marks 6-Million-Ton Cleanup Milestone

    Broader source: Energy.gov [DOE]

    MOAB, Utah – 6,000,000 is a big number, and it marks a significant cleanup milestone in the Beehive State.

  14. Sandia's Distributed Energy Lab Marks FY15 Accomplishments, Adds...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Distributed Energy Lab Marks FY15 Accomplishments, Adds New Capabilities - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate ...

  15. Sandia Energy - Mark Boslough Featured in NOVA Special about...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    in NOVA Special about the Chelyabinsk Meteor Scientist Mark Boslough (Discrete Mathematics and Complex Systems Dept.) was featured in NOVA's special program "Meteor Strike,"...

  16. Written Statement of Mark Whitney Acting Assistant Secretary...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Acting Assistant Secretary for Environmental Management United States Department of Energy ... Written Statement of Mark Whitney Acting Assistant Secretary for Environmental ...

  17. Testimony of Mark Whitney Acting Assistant Secretary for Environmental...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Acting Assistant Secretary for Environmental Management U.S. Department of Energy Before ... Testimony of Mark Whitney Acting Assistant Secretary for Environmental Management U.S. ...

  18. Advanced Manufacturing Office FY 2017 Budget At-A-Glance

    Broader source: Energy.gov [DOE]

    The Advanced Manufacturing Office (AMO) brings together manufacturers, research institutions, suppliers, and universities to investigate manufacturing processes, information, and materials technologies critical to advance domestic manufacturing of clean energy products, and to support energy productivity across the entire manufacturing sector.

  19. EA-367 EDF Trading North America, LLC | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    7 EDF Trading North America, LLC EA-367 EDF Trading North America, LLC Order authorizing EDF Trading North America, LLC to export electric energy to Canada PDF icon EA-367 EDF ...

  20. EA-208 Williams Energy Marketing and Trading Company | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Trading Company More Documents & Publications EA-184 Morgan Stanley Capital Group Inc. EA-166 Duke Energy Trading and Marketing, L.L.C EA-167 PG&E Energy Trading-Power, L.P...

  1. EA-211-C DTE Energy Trading, Inc | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    C DTE Energy Trading, Inc EA-211-C DTE Energy Trading, Inc Order authorizing DTE Energy Trading to export electric energy to Canada. PDF icon EA-211-C DTE.pdf More Documents & ...

  2. CIAM Puresky Carbon Trading Ltd | Open Energy Information

    Open Energy Info (EERE)

    CIAM Puresky Carbon Trading Ltd Jump to: navigation, search Name: CIAM-Puresky Carbon Trading Ltd Place: Shenzhen, China Product: Shenzhen-based JV providing a trading platform for...

  3. EA-373 EDF Trading North America, LLC | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    EA-373 EDF Trading North America, LLC Order authorizong EDF Trading North America, LLCto exprto electric energy to Mexico. PDF icon EA-373 EDF Trading North America, LLC More ...

  4. Manufacturing

    Office of Environmental Management (EM)

    ... (waste and waste water management) and emerged 201 as a field in response to concern over widespread environmental quality degradation from water and air 202 pollution impacts. ...

  5. DOE Proposes New Rules to Protect Trade Secrets and Confidential...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Proposes New Rules to Protect Trade Secrets and Confidential Business Information DOE Proposes New Rules to Protect Trade Secrets and Confidential Business Information March 8,...

  6. EA-223 CMS Marketing, Services and Trading Company | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Trading Company to export electric energy to Canada. EA-223 CMS Marketing, Services and Trading Company More Documents & Publications EA-232 OGE Energy Resources Inc EA-249...

  7. International Ethanol Trade Association IETHA | Open Energy Informatio...

    Open Energy Info (EERE)

    Trade Association IETHA Jump to: navigation, search Name: International Ethanol Trade Association (IETHA) Place: Sao Paulo, Sao Paulo, Brazil Product: Association of 48 globally...

  8. UK Department of Trade and Industry Renewables Group | Open Energy...

    Open Energy Info (EERE)

    Trade and Industry Renewables Group Jump to: navigation, search Name: UK Department of Trade and Industry Renewables Group Place: London, United Kingdom Sector: Renewable Energy...

  9. PSEG Energy Resources and Trade | Open Energy Information

    Open Energy Info (EERE)

    Energy Resources and Trade Jump to: navigation, search Name: PSEG Energy Resources and Trade Place: New Jersey Phone Number: 1-800-436-7734 Website: pseg.comfamilypower...

  10. Hunan Yongzhou Hengli Economy Trade Investment Co Ltd | Open...

    Open Energy Info (EERE)

    Yongzhou Hengli Economy Trade Investment Co Ltd Jump to: navigation, search Name: Hunan Yongzhou Hengli Economy&Trade Investment Co.,Ltd Place: Yongzhou, Hunan Province, China Zip:...

  11. Yingjiang County Mingliang Trading Co Ltd | Open Energy Information

    Open Energy Info (EERE)

    Mingliang Trading Co Ltd Jump to: navigation, search Name: Yingjiang County Mingliang Trading Co., Ltd. Place: Dohong Dai-Jingpo Autonomous Prefecture, Yunnan Province, China Zip:...

  12. Sempra Energy Trading Corp (Washington) | Open Energy Information

    Open Energy Info (EERE)

    Sempra Energy Trading Corp (Washington) Jump to: navigation, search Name: Sempra Energy Trading Corp Place: Washington Phone Number: (877) SEMPRA1 Website: www.sempra.com Twitter:...

  13. High Performance Home Cost Performance Trade-Offs: Production...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    High Performance Home Cost Performance Trade-Offs: Production Builders - Building America Top Innovation High Performance Home Cost Performance Trade-Offs: Production Builders - ...

  14. Engaging Efficiency First Chapters and Other Trade Associations...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency First Chapters and Other Trade Associations in Energy Efficiency Programs Engaging Efficiency First Chapters and Other Trade Associations in Energy Efficiency Programs ...

  15. Aid for Trade and Climate Change Financing Mechanisms | Open...

    Open Energy Info (EERE)

    Aid for Trade and Climate Change Financing Mechanisms Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Aid for Trade and Climate Change Financing Mechanisms: Best...

  16. Shanghai Fan Qie Trading Ltd | Open Energy Information

    Open Energy Info (EERE)

    Shanghai Fan Qie Trading Ltd Place: Shanghai Municipality, China Sector: Solar Product: Solar panel wholesaler and system integrator. References: Shanghai Fan Qie Trading Ltd1...

  17. Federal Energy Management Trade Show | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Federal Energy Management Trade Show Federal Energy Management Trade Show Addthis 1 of 4 Timothy Unruh, Program Manager for the Office of Energy Efficiency and Renewable Energy...

  18. DayStar Solar LLC formerly International Energy Trading LLC ...

    Open Energy Info (EERE)

    LLC formerly International Energy Trading LLC Jump to: navigation, search Name: DayStar Solar LLC (formerly International Energy Trading LLC) Place: Grass Valley, California Zip:...

  19. EA-208 Williams Energy Marketing and Trading Company | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Order authorizing Williams Energy Marketing and Trading Company to export electric energy to Mexico. PDF icon EA-208 Williams Energy Marketing and Trading Company More Documents & ...

  20. EA-178-B Edison Mission Marketing & Trading, Inc | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Order authorizing Edison Mission Marketing & Trading, Inc to export electric energy to Mexico. PDF icon EA-178-B Edison Mission Marketing & Trading, Inc More Documents & ...

  1. Additive Manufacturing: Technology and Applications

    Energy Savers [EERE]

    Lower energy intensity: These techniques save energy by eliminating production steps, using substantially less material, enabling reuse of by-products, and producing lighter products. Remanufacturing parts through advanced additive manufacturing and surface treatment processes can also return end-of-life products to as-new condition, 1 using only 2-25% of the energy required to make new parts. 2 * Less waste: Building objects up layer by layer, instead of traditional machining processes that

  2. Geothermal Heat Pump Manufacturing Activities

    Gasoline and Diesel Fuel Update (EIA)

    0 Geothermal heat pump domestic shipments by customer type, 2008 and 2009 (rated capacity in tons) Customer 2008 2009 Exporter - - Wholesale Distributor 184,869 173,065 Retail Distributor 1,256 10,463 Installer 160,084 154,321 End-User 413 840 U.S. Total 346,622 338,689 - = No data reported. Source: U.S. Energy Information Administration (EIA), Form EIA-902, "Annual Geothermal Heat Pump Manufacturers Survey

  3. Geothermal Heat Pump Manufacturing Activities

    Gasoline and Diesel Fuel Update (EIA)

    5 Companies involved in geothermal heat pump activities by type, 2008 and 2009 Type of Activity 2008 2009 Geothermal Heat Pump or System Design 17 17 Prototype Geothermal Heat Pump Development 12 13 Prototype Systems Geothermal Development 5 7 Wholesale Distribution 15 18 Retail Distribution 3 3 Installation 4 3 Manufacture of System Components 3 4 Source: U.S. Energy Information Administration (EIA), Form EIA-902, "Annual Geothermal

  4. Solar Thermal Collector Manufacturing Activities

    Gasoline and Diesel Fuel Update (EIA)

    5 Shipments of complete solar thermal collector systems, 2008 and 2009 Shipment Information 2008 2009 Complete Collector Systems Shipped 63,961 75,066 Thousand Square Feet 4,058 5,995 Percent of Total Shipments 24 43 Number of Companies 46 62 Revenue of Systems (Thousand Dollars) 47,523 159,085 Source: U.S. Energy Information Administration, Form EIA-63A, "Annual Solar Thermal Collector Manufacturers Survey."

  5. Solar Thermal Collector Manufacturing Activities

    Gasoline and Diesel Fuel Update (EIA)

    9 Companies involved in solar thermal collector related activities by type, 2008 and 2009 Type of Activity 2008 2009 Collector or System Design 45 59 Prototype Collector Development 27 27 Prototype System Development 23 23 Wholesale Distribution 58 61 Retail Distribution 29 31 Installation 21 27 Noncollector System Component Manufacture 26 32 Source: U.S. Energy Information Administration, Form EIA-63A, "Annual Solar Thermal

  6. Solar Thermal Collector Manufacturing Activities

    Gasoline and Diesel Fuel Update (EIA)

    0 Soloar-related sales as a percentage of total company sales revenue, 2008 and 2009 2008 2009 90-100 49 56 50-89 9 7 10-49 7 12 Less than 10 9 13 U.S. Total 74 88 Percent of Total Sales Revenue Number of Companies Source: U.S. Energy Information Administration, Form EIA-63A, "Annual Solar Thermal Collector Manufacturers Survey."

  7. Manufacturing of Plutonium Tensile Specimens

    SciTech Connect (OSTI)

    Knapp, Cameron M

    2012-08-01

    Details workflow conducted to manufacture high density alpha Plutonium tensile specimens to support Los Alamos National Laboratory's science campaigns. Introduces topics including the metallurgical challenge of Plutonium and the use of high performance super-computing to drive design. Addresses the utilization of Abaqus finite element analysis, programmable computer numerical controlled (CNC) machining, as well as glove box ergonomics and safety in order to design a process that will yield high quality Plutonium tensile specimens.

  8. Construction on Pantex High Explosives Pressing Facility Reaches 85% Mark |

    National Nuclear Security Administration (NNSA)

    National Nuclear Security Administration Construction on Pantex High Explosives Pressing Facility Reaches 85% Mark January 03, 2014 Work on the National Nuclear Security Administration's (NNSA) High Explosives Pressing Facility at its Pantex Plant, located near Amarillo, Texas, this month passed the 85 percent construction completion mark and is on schedule and under budget. File 2014-01-03 NPO HEPF

  9. Heat Management Strategy Trade Study

    SciTech Connect (OSTI)

    Nick Soelberg; Steve Priebe; Dirk Gombert; Ted Bauer

    2009-09-01

    This Heat Management Trade Study was performed in 2008-2009 to expand on prior studies in continued efforts to analyze and evaluate options for cost-effectively managing SNF reprocessing wastes. The primary objective was to develop a simplified cost/benefit evaluation for spent nuclear fuel (SNF) reprocessing that combines the characteristics of the waste generated through reprocessing with the impacts of the waste on heating the repository. Under consideration were age of the SNF prior to reprocessing, plutonium and minor actinide (MA) separation from the spent fuel for recycle, fuel value of the recycled Pu and MA, age of the remaining spent fuel waste prior to emplacement in the repository, length of time that active ventilation is employed in the repository, and elemental concentration and heat limits for acceptable glass waste form durability. A secondary objective was to identify and qualitatively analyze remaining issues such as (a) impacts of aging SNF prior to reprocessing on the fuel value of the recovered fissile materials, and (b) impact of reprocessing on the dose risk as developed in the Yucca Mountain Total System Performance Assessment (TSPA). Results of this study can be used to evaluate different options for managing decay heat in waste streams from spent nuclear fuel.

  10. Artisan Manufacturing: Order (2010-CW-0712)

    Broader source: Energy.gov [DOE]

    DOE ordered Artisan Manufacturing Company, Inc., to pay a $5,000 civil penalty after finding Artisan Manufacturing had failed to certify that certain models of faucets comply with the applicable water conservation standard.

  11. Advanced Methods for Manufacturing Newslettter- Issue 3

    Broader source: Energy.gov [DOE]

    The Advanced Methods for Manufacturing newsletter includes information about selected projects pertaining to additive manufacturing, concrete technologies, welding innovations and imaging techniques for design reconstruction currently funded by the Department of Energy's Office of Nuclear Energy.

  12. Refrigerator Manufacturers: Order (2013-CE-5341)

    Broader source: Energy.gov [DOE]

    DOE ordered Refrigerator Manufacturers, LLC to pay a $8,000 civil penalty after finding Refrigerator Manufacturers had failed to certify that certain models of walk-in cooler and freezer components comply with the applicable energy conservation standards.

  13. USA Manufacturing: Order (2013-CE-5336)

    Broader source: Energy.gov [DOE]

    DOE ordered USA Manufacturing to pay a $8,000 civil penalty after finding USA Manufacturing had failed to certify that certain models of walk-in cooler and freezer components comply with the applicable energy conservation standards.

  14. Clean Energy Manufacturing Initiative: Technology Research and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Its Advanced Natural Gas Systems Manufacturing Initiative's R&D is helping U.S. manufacturers take advantage of this lower-priced fuel by modernizing the nations natural gas ...

  15. National Manufacturing Day | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    anticipated 400,000 people who want to experience U.S. manufacturing up close and in person. On October 2, the U.S. Department of Commerce's fourth annual Manufacturing Day will...

  16. QTR Webinar: Chapter 8- Industry and Manufacturing

    Broader source: Energy.gov [DOE]

    The DOE EERE Advanced Manufacturing Office hosted a QTR webinar to obtain input from Leaders in Academia, Industry, and Government on Chapter 8, Industry and Manufacturing, and the associated Technology Assessments.

  17. Imperial Manufacturing: Order (2013-CE-5322)

    Broader source: Energy.gov [DOE]

    DOE ordered Imperial Manufacturing, Inc. to pay a $8,000 civil penalty after finding Imperial Manufacturing had failed to certify that certain models of walk-in cooler and freezer components comply with the applicable energy conservation standards.

  18. Clean Energy Manufacturing Incentive Grant Program

    Office of Energy Efficiency and Renewable Energy (EERE)

    "Clean energy manufacturer" is defined as a biofuel producer, a manufacturer of renewable energy or nuclear equipment/products, or "products used for energy conservation, storage, or grid efficie...

  19. AMO Hosted Workshop on Composite Manufacturing

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy's Advanced Manufacturing Office will host a workshop on Fiber Reinforced Polymer Composite Manufacturing on January 13, 2014 at the Hilton Crystal City in Arlington, VA.

  20. Goodman Manufacturing: Order (2012-CE-1509)

    Broader source: Energy.gov [DOE]

    DOE ordered Goodman Manufacturing Company L.P. to pay an $8,000 civil penalty after finding Goodman Manufacturing had failed to certify that certain room air conditioners comply with the applicable energy conservation standard.

  1. Goodman Manufacturing: Proposed Penalty (2011-SE-4301)

    Broader source: Energy.gov [DOE]

    DOE alleged in a Notice of Proposed Civil Penalty that Goodman Manufacturing manufactured and distributed noncompliant basic model CPC180* commercial package air conditioners in the U.S.

  2. Energy & Manufacturing Workforce Training Topics List - Version...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    & Manufacturing Workforce Training Topics List - Version 1.7 (02.11.14) Energy & Manufacturing Workforce Training Topics List - Version 1.7 (02.11.14) View this searchable list of ...

  3. FACT SHEET: 48C MANUFACTURING TAX CREDITS

    Broader source: Energy.gov [DOE]

    The Advanced Energy Manufacturing Tax Credit Program is helping build a robust U.S. manufacturing capacity to supply clean energy projects with American-made parts and equipment. On February 7,...

  4. Summit Manufacturing: Case Closure (2010-SE-0303)

    Broader source: Energy.gov [DOE]

    DOE closed this case against Summit Manufacturing, Inc. without civil penalty after Summit Manufacturing provided information that the non-compliant products were not sold in the United States.

  5. Advanced Manufacturing Office | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Advanced Manufacturing Office NOTICE OF INTENT: Clean Energy Manufacturing Innovation Institute for Reducing Energy of Materials And Decreasing Emissions in M NOTICE OF INTENT: Clean Energy Manufacturing Innovation Institute for Reducing Energy of Materials And Decreasing Emissions in M The Energy Department intends to issue a Funding Opportunity Announcement for approximately $70 million entitled "Clean Energy Manufacturing Innovation Institute for Reducing EMbodied-energy And Decreasing

  6. Clean Energy Manufacturing Initiative | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Clean Energy Manufacturing Initiative AEMC Northeast Regional Summit AEMC Northeast Regional Summit On May 12, 2016, join Assistant Secretary Dr. Dave Danielson for an unforgettable dialogue on advances and obstacles in clean energy manufacturing in the northeast and across the nation. Read more Funding Opportunity: High-Performance Computing for Manufacturing Funding Opportunity: High-Performance Computing for Manufacturing The Energy Department announced up to $3 million in funding for

  7. advanced manufacturing office | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Advanced Manufacturing Office The U.S. Department of Energy (DOE) funds the research, development, and demonstration of highly efficient and innovative manufacturing technologies. DOE has supported the development of more than 250 energy-saving industrial technologies that have been commercialized since 1976. DOE is also working to create a network of Manufacturing Innovation Institutes, each of which will create collaborative communities to target a unique technology in advanced manufacturing.

  8. Advanced Manufacturing Initiative Improves Turbine Blade Productivity |

    Energy Savers [EERE]

    Department of Energy Advanced Manufacturing Initiative Improves Turbine Blade Productivity Advanced Manufacturing Initiative Improves Turbine Blade Productivity May 20, 2011 - 2:56pm Addthis This is an excerpt from the Second Quarter 2011 edition of the Wind Program R&D Newsletter. The Advanced Manufacturing Initiative (AMI) at DOE's Sandia National Laboratories is working with industry to improve manufacturing processes and create U.S. jobs by improving labor productivity in wind

  9. Clean Energy Manufacturing Initiative Industrial Efficiency and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Industrial Efficiency and Energy Productivity Video Clean Energy Manufacturing Initiative Industrial Efficiency and Energy Productivity Video Addthis Description Industrial ...

  10. Partnering for Clean Energy Manufacturing Competitiveness

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Libby Wayman Director, Clean Energy Manufacturing Initiative Partnering for Clean Energy Manufacturing Competitiveness 2 Mission: To create American leadership in the global transition to a clean energy economy 1) High-Impact Research, Development, and Demonstration to Make Clean Energy as Affordable and Convenient as Traditional Forms of Energy 2) Breaking Down Barriers to Market Entry 3 Coordination of Clean Energy Manufacturing in EERE Coordination for: * Clean Energy Manufacturing Strategies

  11. Manufacturing Demonstration Facilities Workshop, March 12, 2012

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... public sectors) National PolicySecurity Objectives * ... Approach: * Provide manufacturers and product developers ... Plan * Financial Sustainability * Intellectual Property ...

  12. Clean Energy Manufacturing Analysis Center Webinar

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy offers a webinar to address clean energy manufacturing on April 5. Register today!

  13. Clean Energy Manufacturing Innovation Institute for Composite...

    Broader source: Energy.gov (indexed) [DOE]

    and Fuel Cell Technologies Research, Development, and Demonstrations Funding Opportunity Announcement Webinar Slides Fiber Reinforced Polymer Composite Manufacturing Workshop

  14. Manufacturing Demonstration Facilities Workshop, March 12, 2012 |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Demonstration Facilities Workshop, March 12, 2012 Manufacturing Demonstration Facilities Workshop, March 12, 2012 PDF icon mdf_workshop_presentation_march2012.pdf More Documents & Publications Manufacturing Demonstration Facility Workshop Microwave and Radio Frequency Workshop Microwave (MW) and Radio Frequency (RF) as Enabling Technologies for Advanced Manufacturing

  15. Manufacturing Demonstration Facility Workshop | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Demonstration Facility Workshop Manufacturing Demonstration Facility Workshop March 12, 2012 The Manufacturing Demonstration Facility Workshop (held in Chicago, IL, on March 12, 2012, and simultaneously broadcast as a webinar) invited stakeholders to discuss key foundational aspects of planning a series of Manufacturing Demonstration Facilities (MDFs). MDFs will create a collaborative, shared infrastructure around targeted technical areas that will develop, use, and promote energy efficient,

  16. Clean Energy Manufacturing Initiative Midwest Regional Summit:

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Lightweighting Breakout Session Summary | Department of Energy Clean Energy Manufacturing Initiative Midwest Regional Summit: Lightweighting Breakout Session Summary Clean Energy Manufacturing Initiative Midwest Regional Summit: Lightweighting Breakout Session Summary Clean Energy Manufacturing Initiative Midwest Regional Summit: Lightweighting Breakout Session Summary June 21, 2013 PDF icon Lightweighting Breakout Session Summary More Documents & Publications Fiber Reinforced Polymer

  17. Trade My Food | Open Energy Information

    Open Energy Info (EERE)

    search for food they would like to trade for. Example: Alicia grows parsley, Bob is a fisherman. Alicia wants some fish. Bob wants some parsley. They find each other on...

  18. Electric trade in the United States 1994

    SciTech Connect (OSTI)

    1998-08-01

    Wholesale trade in electricity plays an important role for the US electric utility industry. Wholesale, or bulk power, transactions allow electric utilities to reduce power costs, increase power supply options, and improve reliability. In 1994, the wholesale trade market totaled 1.9 trillion kilowatthours, about 66% of total sales to ultimate consumers. This publication, Electric Trade in the United States 1994 (ELECTRA), is the fifth in a series of reports on wholesale power transactions prepared by the Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA). The electric trade data are published biennially. The first report presented 1986 data, and this report provides information on the electric power industry during 1994.

  19. Clean Air Trade Inc | Open Energy Information

    Open Energy Info (EERE)

    a company specialising in CER purchase as well as project development and investment in clean energy. References: Clean Air Trade Inc1 This article is a stub. You can help OpenEI...

  20. MANUFACTURING CALIFORNIA LAWRENCE BERKELEY LAB POC David Chen

    Energy Savers [EERE]

    MANUFACTURING CALIFORNIA LAWRENCE BERKELEY LAB POC David Chen Telephone (510) 486-4506 Email dtchen@lbl.gov Industrial Gas Manufacturing 325120 All Other Basic Inorganic Chemical Manufacturing 325188 Plastics Material and Resin Manufacturing 325211 Explosives Manufacturing 325920 All Other Plastics Product Manufacturing 326199 Nonferrous Metal (except Copper and Aluminum) Rolling, Drawing, and Extruding 331491 Fabricated Structural Metal Manufacturing 332312 Metal Tank (Heavy Gauge)

  1. Manufacturing Demonstration Facility Workshop Videos | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Manufacturing Demonstration Facility Workshop Videos Manufacturing Demonstration Facility Workshop Videos Dr. Leo Christodoulou, Program Manager, EERE Advanced Manufacturing Office, and Mike Molnar, Chief Manufacturing Officer, National Institute of Standards & Technology, speaking at the Manufacturing Demonstration Facility Workshop held in Chicago, Illinois Dr. Leo Christodoulou, Program Manager, EERE Advanced Manufacturing Office speaking at the Manufacturing Demonstration Facility

  2. Electric trade in the United States, 1996

    SciTech Connect (OSTI)

    1998-12-01

    Wholesale trade in electricity plays an important role for the US electric utility industry. Wholesale, or bulk power, transactions allow electric utilities to reduce power costs, increase power supply options, and improve reliability. In 1996, the wholesale trade market totaled 2.3 trillion kilowatthours, over 73% of total sales to ultimate consumers. This publication, Electric Trade in the United States 1996 (ELECTRA), is the sixth in a series of reports on wholesale power transactions prepared by the Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA). The electric trade data are published biennially. The first report presented 1986 data, and this report provides information on the electric power industry during 1996. The electric trade data collected and presented in this report furnish important information on the wholesale structure found within the US electric power industry. The patterns of interutility trade in the report support analyses of wholesale power transactions and provide input for a broader understanding of bulk power market issues that define the emerging national electric energy policies. The report includes information on the quantity of power purchased, sold, exchanged, and wheeled; the geographical locations of transactions and ownership classes involved; and the revenues and costs. 1 fig., 43 tabs.

  3. Ohio Advanced Energy Manufacturing Center

    SciTech Connect (OSTI)

    Kimberly Gibson; Mark Norfolk

    2012-07-30

    The program goal of the Ohio Advanced Energy Manufacturing Center (OAEMC) is to support advanced energy manufacturing and to create responsive manufacturing clusters that will support the production of advanced energy and energy-efficient products to help ensure the nation's energy and environmental security. This goal cuts across a number of existing industry segments critical to the nation's future. Many of the advanced energy businesses are starting to make the transition from technology development to commercial production. Historically, this transition from laboratory prototypes through initial production for early adopters to full production for mass markets has taken several years. Developing and implementing manufacturing technology to enable production at a price point the market will accept is a key step. Since these start-up operations are configured to advance the technology readiness of the core energy technology, they have neither the expertise nor the resources to address manufacturing readiness issues they encounter as the technology advances toward market entry. Given the economic realities of today's business environment, finding ways to accelerate this transition can make the difference between success and failure for a new product or business. The advanced energy industry touches a wide range of industry segments that are not accustomed to working together in complex supply chains to serve large markets such as automotive and construction. During its first three years, the Center has catalyzed the communication between companies and industry groups that serve the wide range of advanced energy markets. The Center has also found areas of common concern, and worked to help companies address these concerns on a segment or industry basis rather than having each company work to solve common problems individually. EWI worked with three industries through public-private partnerships to sew together disparate segments helping to promote overall industry health. To aid the overall advanced energy industry, EWI developed and launched an Ohio chapter of the non-profit Advanced Energy Economy. In this venture, Ohio joins with six other states including Colorado, Connecticut, Illinois, Maine, Massachusetts, New Hampshire, Rhode Island and Vermont to help promote technologies that deliver energy that is affordable, abundant and secure. In a more specific arena, EWI's advanced energy group collaborated with the EWI-run Nuclear Fabrication Consortium to promote the nuclear supply chain. Through this project EWI has helped bring the supply chain up to date for the upcoming period of construction, and assisted them in understanding the demands for the next generation of facilities now being designed. In a more targeted manner, EWI worked with 115 individual advanced energy companies that are attempting to bring new technology to market. First, these interactions helped EWI develop an awareness of issues common to companies in different advanced energy sectors. By identifying and addressing common issues, EWI helps companies bring technology to market sooner and at a lower cost. These visits also helped EWI develop a picture of industry capability. This helped EWI provide companies with contacts that can supply commercial solutions to their new product development challenges. By providing assistance in developing supply chain partnerships, EWI helped companies bring their technology to market faster and at a lower cost than they might have been able to do by themselves. Finally, at the most granular level EWI performed dedicated research and development on new manufacturing processes for advanced energy. During discussions with companies participating in advanced energy markets, several technology issues that cut across market segments were identified. To address some of these issues, three crosscutting technology development projects were initiated and completed with Center support. This included reversible welds for batteries and high temperature heat exchangers. It also included a novel advanced weld trainer that EWI has recently commercialized.

  4. DOE Logo, Seal and Word Mark | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Graphics » DOE Logo, Seal and Word Mark DOE Logo, Seal and Word Mark The DOE logo, seal, and word mark are official graphical identifiers of the U.S. Department of Energy and are meant for official use only, to represent the Department's official position. They may be used to recognize funding or official support by the Department if the usage has proper qualifying language to explain its presence on non-DOE materials and it is reviewed and explicitly approved by the Department. They cannot be

  5. Manufacturing method of photonic crystal

    DOE Patents [OSTI]

    Park, In Sung; Lee, Tae Ho; Ahn, Jin Ho; Biswas, Rana; Constant, Kristen P.; Ho, Kai-Ming; Lee, Jae-Hwang

    2013-01-29

    A manufacturing method of a photonic crystal is provided. In the method, a high-refractive-index material is conformally deposited on an exposed portion of a periodic template composed of a low-refractive-index material by an atomic layer deposition process so that a difference in refractive indices or dielectric constants between the template and adjacent air becomes greater, which makes it possible to form a three-dimensional photonic crystal having a superior photonic bandgap. Herein, the three-dimensional structure may be prepared by a layer-by-layer method.

  6. Method for manufacturing magnetohydrodynamic electrodes

    DOE Patents [OSTI]

    Killpatrick, D.H.; Thresh, H.R.

    1980-06-24

    A method of manufacturing electrodes for use in a magnetohydrodynamic (MHD) generator is described comprising the steps of preparing a billet having a core of a first metal, a tubular sleeve of a second metal, and an outer sheath of an extrusile metal; evacuating the space between the parts of the assembled billet; extruding the billet; and removing the outer jacket. The extruded bar may be made into electrodes by cutting and bending to the shape required for an MHD channel frame. The method forms a bond between the first metal of the core and the second metal of the sleeve strong enough to withstand a hot and corrosive environment.

  7. Geothermal Heat Pump Manufacturing Activities

    Gasoline and Diesel Fuel Update (EIA)

    9 Distribution of U.S. geothermal heat pump imports by country of origin, 2008 and 2009 (rated capacity in tons) Asia China 86 250 100.00 Total 86 250 100.00 U.S. Total 86 250 100.00 Region/Country 2008 2009 Percent of U.S. Imports 2009 Note: Totals may not equal sum of components due to independent rounding. Source: U.S. Energy Information Administration (EIA), Form EIA-902, "Annual Geothermal Heat Pump Manufacturers Survey

  8. Solar Thermal Collector Manufacturing Activities

    Gasoline and Diesel Fuel Update (EIA)

    1 Distribution of domestic solar thermal collector shipments (thousand square feet) 2008 2009 Wholesale Distributors 8,680 4,063 Retail Distributors 3,997 5,739 Exporters 368 346 Installers 948 939 End Users 723 1,134 U.S. Total 14,716 12,221 Customer Type Shipments Notes: Totals may not equal sum of components due to independent rounding. U.S. total includes territories. Source: U.S. Energy Information Administration, Form EIA-63A, "Annual Solar Thermal Collector Manufacturers Survey

  9. Solar Thermal Collector Manufacturing Activities

    Gasoline and Diesel Fuel Update (EIA)

    4 Average thermal performance rating of solar thermal collectors by type shipped in 2009 (Btu per square foot per day) Low- High Temperature Temperature Liquid/air Parabolic Year Metallic and Nonmetallic Air ICS/Thermosi phon Flat-Plate (Pumped) Evaculated Tube Concentrator Paraboloic Dish/Trough 2009 1,139 971 913 981 973 2,196 1,262 Source: U.S. Energy Information Administration, Form EIA-63A, "Annual Solar Thermal Collector Manufacturers Survey." Medium-Temperature Type Liquid

  10. Process for manufacturing tantalum capacitors

    DOE Patents [OSTI]

    Lauf, R.J.; Holcombe, C.E.; Dykes, N.L.

    1993-02-02

    A process for manufacturing tantalum capacitors in which microwave energy is used to sinter a tantalum powder compact in order to achieve higher surface area and improved dielectric strength. The process comprises cold pressing tantalum powder with organic binders and lubricants to form a porous compact. After removal of the organics, the tantalum compact is heated to 1,300 to 2,000 C by applying microwave radiation. Said compact is then anodized to form a dielectric oxide layer and infiltrated with a conductive material such as MnO[sub 2]. Wire leads are then attached to form a capacitor to said capacitor is hermetically packaged to form the finished product.

  11. Process for manufacturing tantalum capacitors

    DOE Patents [OSTI]

    Lauf, Robert J.; Holcombe, Cressie E.; Dykes, Norman L.

    1993-01-01

    A process for manufacturing tantalum capacitors in which microwave energy is used to sinter a tantalum powder compact in order to achieve higher surface area and improved dielectric strength. The process comprises cold pressing tantalum powder with organic binders and lubricants to form a porous compact. After removal of the organics, the tantalum compact is heated to 1300.degree. to 2000.degree. C. by applying microwave radiation. Said compact is then anodized to form a dielectric oxide layer and infiltrated with a conductive material such as MnO.sub.2. Wire leads are then attached to form a capacitor to said capacitor is hermetically packaged to form the finished product.

  12. Method for automatically evaluating a transition from a batch manufacturing technique to a lean manufacturing technique

    DOE Patents [OSTI]

    Ivezic, Nenad; Potok, Thomas E.

    2003-09-30

    A method for automatically evaluating a manufacturing technique comprises the steps of: receiving from a user manufacturing process step parameters characterizing a manufacturing process; accepting from the user a selection for an analysis of a particular lean manufacturing technique; automatically compiling process step data for each process step in the manufacturing process; automatically calculating process metrics from a summation of the compiled process step data for each process step; and, presenting the automatically calculated process metrics to the user. A method for evaluating a transition from a batch manufacturing technique to a lean manufacturing technique can comprise the steps of: collecting manufacturing process step characterization parameters; selecting a lean manufacturing technique for analysis; communicating the selected lean manufacturing technique and the manufacturing process step characterization parameters to an automatic manufacturing technique evaluation engine having a mathematical model for generating manufacturing technique evaluation data; and, using the lean manufacturing technique evaluation data to determine whether to transition from an existing manufacturing technique to the selected lean manufacturing technique.

  13. Manufacturing Energy Consumption Survey (MECS) - U.S. Energy...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Residential - RECS Transportation DOE Uses MECS Data Manufacturing Energy and Carbon Footprints Associated Analysis Manufacturing Energy Sankey Diagrams Manufacturing Energy Flows ...

  14. SunShot Photovoltaic Manufacturing Initiative | Department of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technology to Market SunShot Photovoltaic Manufacturing Initiative SunShot Photovoltaic Manufacturing Initiative The SunShot Photovoltaic Manufacturing Initiative (PVMI) invests ...

  15. Webtrends Archives by Fiscal Year - Advanced Manufacturing Office...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Advanced Manufacturing Office Webtrends Archives by Fiscal Year - Advanced Manufacturing Office From the EERE Web Statistics Archive: Advanced Manufacturing Office, Webtrends ...

  16. $23.5 Million Investment in Innovative Manufacturing Projects...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    23.5 Million Investment in Innovative Manufacturing Projects Supports the New Clean Energy Manufacturing Initiative 23.5 Million Investment in Innovative Manufacturing Projects ...

  17. Notice of Intent (NOI): Clean Energy Manufacturing Innovation...

    Broader source: Energy.gov (indexed) [DOE]

    Energy Manufacturing Innovation Institute on Smart Manufacturing: Advanced Sensors, Controls, Platforms, and Modeling for Manufacturing" (DE-FOA-0001263). This is a Notice of...

  18. 1991 Manufacturing Consumption of Energy 1991 Executive Summary

    U.S. Energy Information Administration (EIA) Indexed Site

    Summary The Manufacturing Consumption of Energy 1991 report presents statistics about the energy consumption of the manufacturing sector, based on the 1991 Manufacturing Energy...

  19. Phase plate technology for laser marking of magnetic discs

    DOE Patents [OSTI]

    Neuman, B.; Honig, J.; Hackel, L.; Dane, C.B.; Dixit, S.

    1998-10-27

    An advanced design for a phase plate enables the distribution of spots in arbitrarily shaped patterns with very high uniformity and with a continuously or near-continuously varying phase pattern. A continuous phase pattern eliminates large phase jumps typically expected in a grating that provides arbitrary shapes. Large phase jumps increase scattered light outside of the desired pattern, reduce efficiency and can make the grating difficult to manufacture. When manufacturing capabilities preclude producing a fully continuous grating, the present design can be easily adapted to minimize manufacturing errors and maintain high efficiencies. This continuous grating is significantly more efficient than previously described Dammann gratings, offers much more flexibility in generating spot patterns and is easier to manufacture and replicate than a multi-level phase grating. 3 figs.

  20. Phase plate technology for laser marking of magnetic discs

    DOE Patents [OSTI]

    Neuman, Bill; Honig, John; Hackel, Lloyd; Dane, C. Brent; Dixit, Shamasundar

    1998-01-01

    An advanced design for a phase plate enables the distribution of spots in arbitrarily shaped patterns with very high uniformity and with a continuously or near-continuously varying phase pattern. A continuous phase pattern eliminates large phase jumps typically expected in a grating that provides arbitrary shapes. Large phase jumps increase scattered light outside of the desired pattern, reduce efficiency and can make the grating difficult to manufacture. When manufacturing capabilities preclude producing a fully continuous grating, the present design can be easily adapted to minimize manufacturing errors and maintain high efficiencies. This continuous grating is significantly more efficient than previously described Dammann gratings, offers much more flexibility in generating spot patterns and is easier to manufacture and replicate than a multi-level phase grating.

  1. Additive manufacturing of hybrid circuits

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Bell, Nelson S.; Sarobol, Pylin; Cook, Adam; Clem, Paul G.; Keicher, David M.; Hirschfeld, Deidre; Hall, Aaron Christopher

    2016-03-26

    There is a rising interest in developing functional electronics using additively manufactured components. Considerations in materials selection and pathways to forming hybrid circuits and devices must demonstrate useful electronic function; must enable integration; and must complement the complex shape, low cost, high volume, and high functionality of structural but generally electronically passive additively manufactured components. This article reviews several emerging technologies being used in industry and research/development to provide integration advantages of fabricating multilayer hybrid circuits or devices. First, we review a maskless, noncontact, direct write (DW) technology that excels in the deposition of metallic colloid inks for electrical interconnects.more » Second, we review a complementary technology, aerosol deposition (AD), which excels in the deposition of metallic and ceramic powder as consolidated, thick conformal coatings and is additionally patternable through masking. As a result, we show examples of hybrid circuits/devices integrated beyond 2-D planes, using combinations of DW or AD processes and conventional, established processes.« less

  2. FIA-15-0044- In the Matter of Mark Krebs

    Broader source: Energy.gov [DOE]

    On August 18, 2015, OHA (OHA) denied a FOIA Appeal filed by Mark Krebs from a determination issued to him by the DOE Office of Information Resources. In the Appeal, the Appellant challenged the...

  3. How is a Document Containing OUO Marked? | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    with "Document(s) transmitted contain(s) OUO information". (DOE M 471.3-1, Admin Chg 1, Chapter I, 3f.) Marking e-mail: If the e-mail contains OUO information, the first line of ...

  4. ProForce marks 65 years protecting Sandia resources, facilities...

    National Nuclear Security Administration (NNSA)

    ProForce marks 65 years protecting Sandia resources, facilities, people Monday, October ... Over the past 65 years, the force has changed in size and structure but its mission has ...

  5. West Valley Demolition Marks Important Accomplishment for EM

    Broader source: Energy.gov [DOE]

    WEST VALLEY, N.Y. – EM marked one of its most significant achievements at the West Valley Demonstration Project (WVDP) with the completion of the site’s first nuclear facility demolition this spring.

  6. TBU-0002- In the Matter of Mark J. Chugg

    Broader source: Energy.gov [DOE]

    Mark J. Chugg, a former employee of Bechtel BWXT Idaho (BWXT), a Department of Energy (DOE) contractor, appeals the dismissal of his whistleblower complaint filed under 10 C.F.R. Part 708, the DOE...

  7. Testimony of Mark Whitney Principal Deputy Assistant Secretary...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and the Economy House Energy and Commerce Committee Disposal of Low-Level Radioactive Waste and Greater-Than-Class C Waste Testimony of Mark Whitney Principal Deputy Assistant ...

  8. Richland Operations Office FY 14/15 Funding Marks

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Office FY 1415 Funding Marks PBS PBS Title FY 2014 Omnibus (Enacted) FY 2015 President's Budget FY 2015 Omnibus Allocation RL-0011 NM Stabilization and Disposition - PFP 142,670...

  9. Utility of Big Area Additive Manufacturing (BAAM) For The Rapid Manufacture

    Office of Scientific and Technical Information (OSTI)

    of Customized Electric Vehicles (Technical Report) | SciTech Connect Utility of Big Area Additive Manufacturing (BAAM) For The Rapid Manufacture of Customized Electric Vehicles Citation Details In-Document Search Title: Utility of Big Area Additive Manufacturing (BAAM) For The Rapid Manufacture of Customized Electric Vehicles This Oak Ridge National Laboratory (ORNL) Manufacturing Development Facility (MDF) technical collaboration project was conducted in two phases as a CRADA with Local

  10. Green Racing Marks Its 25th Competition | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Racing Marks Its 25th Competition Green Racing Marks Its 25th Competition September 13, 2011 - 5:21pm Addthis One of the competitors from the Michelin Green X Challenge takes center stage outside the National Press Club. | Photo courtesy of Green Racing. One of the competitors from the Michelin Green X Challenge takes center stage outside the National Press Club. | Photo courtesy of Green Racing. Lee Slezak Vehicle Systems and Testing Manager The Green Racing program, a motorsports competition

  11. Simultaneous neuron- and astrocyte-specific fluorescent marking (Journal

    Office of Scientific and Technical Information (OSTI)

    Article) | SciTech Connect Simultaneous neuron- and astrocyte-specific fluorescent marking Citation Details In-Document Search Title: Simultaneous neuron- and astrocyte-specific fluorescent marking Systematic and simultaneous analysis of multiple cell types in the brain is becoming important, but such tools have not yet been adequately developed. Here, we aimed to generate a method for the specific fluorescent labeling of neurons and astrocytes, two major cell types in the brain, and we have

  12. DOE Marks First Anniversary of EPAct & Releases National Electric

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Transmission Congestion Study | Department of Energy First Anniversary of EPAct & Releases National Electric Transmission Congestion Study DOE Marks First Anniversary of EPAct & Releases National Electric Transmission Congestion Study August 8, 2006 - 8:43am Addthis WASHINGTON, DC - U.S. Department of Energy (DOE) Secretary Samuel W. Bodman today marked the one-year anniversary of President Bush's signing of the Energy Policy Act of 2005 (EPAct), highlighting its progress in

  13. Savannah River Site Marks Waste Processing Milestone with Melter's

    Energy Savers [EERE]

    2,000th Waste Canister | Department of Energy Marks Waste Processing Milestone with Melter's 2,000th Waste Canister Savannah River Site Marks Waste Processing Milestone with Melter's 2,000th Waste Canister February 1, 2012 - 12:00pm Addthis A Savannah River Remediation employee uses a manipulator located inside a shielded enclosure at the Defense Waste Processing Facility, where a melter pours molten glass into a canister. A Savannah River Remediation employee uses a manipulator located

  14. Ribbon cutting marks chemistry laboratory upgrades at Northern New Mexico

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    College Ribbon cutting marks chemistry laboratory upgrades at Northern New Mexico College Community Connections: Your link to news and opportunities from Los Alamos National Laboratory Latest Issue:May 2016 all issues All Issues » submit Ribbon cutting marks chemistry laboratory upgrades at Northern New Mexico College Los Alamos National Security, LLC provides support November 1, 2013 Ribbon cutting at Northern New Mexico College As others look on, Northern New Mexico College President

  15. Fluor Paducah Deactivation Project Marks 2 Million Safe Work Hours |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Fluor Paducah Deactivation Project Marks 2 Million Safe Work Hours Fluor Paducah Deactivation Project Marks 2 Million Safe Work Hours March 31, 2016 - 12:05pm Addthis Fluor maintenance mechanic Robert Fulton lifts equipment at the C-337 former uranium enrichment process building at EM’s Paducah Site. Fluor maintenance mechanic Robert Fulton lifts equipment at the C-337 former uranium enrichment process building at EM's Paducah Site. Dale Bristoe and Kelly Robinson

  16. DOE Marks Major Milestone with Startup of Recovery Act Demonstration

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Project | Department of Energy Marks Major Milestone with Startup of Recovery Act Demonstration Project DOE Marks Major Milestone with Startup of Recovery Act Demonstration Project April 9, 2014 - 10:36am Addthis News Media Contact 202-586-4940 Editor's Note: This post has been updated as of April 11, 2014. TAMPA, FL. - Today, the Department of Energy joined RTI International and Tampa Electric Company (TECO) to celebrate the successful startup of a pilot project to demonstrate a warm gas

  17. Construction on Pantex High Explosives Pressing Facility Reaches 85% Mark |

    National Nuclear Security Administration (NNSA)

    National Nuclear Security Administration Construction on Pantex High Explosives Pressing Facility Reaches 85% Mark December 16, 2013 WASHINGTON, D.C. - Work on the National Nuclear Security Administration's (NNSA) High Explosives Pressing Facility at its Pantex Plant, located near Amarillo, Texas, this month passed the 85 percent construction completion mark and is on schedule and under budget. The new 45,000 square-foot state-of-the-art facility will provide safer, more reliable production

  18. Anniversary of Fire, Radiological Events Marks Major Progress at WIPP

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    February 12, 2016 Anniversary of Fire, Radiological Events Marks Major Progress at WIPP February 2016 marks two years since the underground fire and radiological release events forced the temporary closure of the Department of Energy's (DOE) Waste Isolation Pilot Plant (WIPP), near Carlsbad, New Mexico. Since that time much progress has been made in the recovery of the underground including mine stability and habitability, initial panel closure, radiological risk remediation and the addition of

  19. Joint Trade Mission to China | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Joint Trade Mission to China Joint Trade Mission to China Trade Mission Begins Trade Mission Begins The joint trade mission began in Beijing, and will also make stops in Shanghai and Guangzhou. Read more Green Buildings Green Buildings How American Businesses are leading the way in green building technology in Shanghai and around the world. Read more Top 3 Things Top 3 Things Deputy Secretary Sherwood-Randall spoke at Microsoft's Beijing Campus. These were the top 3 things from her speech. Read

  20. Manufactured caverns in carbonate rock

    DOE Patents [OSTI]

    Bruce, David A.; Falta, Ronald W.; Castle, James W.; Murdoch, Lawrence C.

    2007-01-02

    Disclosed is a process for manufacturing underground caverns suitable in one embodiment for storage of large volumes of gaseous or liquid materials. The method is an acid dissolution process that can be utilized to form caverns in carbonate rock formations. The caverns can be used to store large quantities of materials near transportation facilities or destination markets. The caverns can be used for storage of materials including fossil fuels, such as natural gas, refined products formed from fossil fuels, or waste materials, such as hazardous waste materials. The caverns can also be utilized for applications involving human access such as recreation or research. The method can also be utilized to form calcium chloride as a by-product of the cavern formation process.

  1. Means of manufacturing annular arrays

    DOE Patents [OSTI]

    Day, R.A.

    1985-10-10

    A method is described for manufacturing an annular acoustic transducer array from a plate of transducer material, which enables production of precision aligned arrays at low cost. The circular plate is sawed along at least two lines that are radial to the axis of the plate. At steps along each radial cut, the plate is rotated first in one direction and then in an opposite direction by a predetermined angle such as slightly less than 90/sup 0/. The cuts result in the forming of several largely ring-shaped lands, each largely ring-shaped land being joined to the other rings of different radii by thin portions of the plate, and each ring being cut into segments. The bridges that join different rings hold the transducer together until it can be mounted on a lens.

  2. Method for manufacturing magnetohydrodynamic electrodes

    DOE Patents [OSTI]

    Killpatrick, Don H.; Thresh, Henry R.

    1982-01-01

    A method of manufacturing electrodes for use in a magnetohydrodynamic (MHD) generator comprising the steps of preparing a billet having a core 10 of a first metal, a tubular sleeve 12 of a second metal, and an outer sheath 14, 16, 18 of an extrusile metal; evacuating the space between the parts of the assembled billet; extruding the billet; and removing the outer jacket 14. The extruded bar may be made into electrodes by cutting and bending to the shape required for an MDH channel frame. The method forms a bond between the first metal of the core 10 and the second metal of the sleeve 12 strong enough to withstand a hot and corrosive environment.

  3. Wind Turbine Manufacturing Process Monitoring

    SciTech Connect (OSTI)

    Waseem Faidi; Chris Nafis; Shatil Sinha; Chandra Yerramalli; Anthony Waas; Suresh Advani; John Gangloff; Pavel Simacek

    2012-04-26

    To develop a practical inline inspection that could be used in combination with automated composite material placement equipment to economically manufacture high performance and reliable carbon composite wind turbine blade spar caps. The approach technical feasibility and cost benefit will be assessed to provide a solid basis for further development and implementation in the wind turbine industry. The program is focused on the following technology development: (1) Develop in-line monitoring methods, using optical metrology and ultrasound inspection, and perform a demonstration in the lab. This includes development of the approach and performing appropriate demonstration in the lab; (2) Develop methods to predict composite strength reduction due to defects; and (3) Develop process models to predict defects from leading indicators found in the uncured composites.

  4. USCAR LEP ESST Advanced Manufacturing

    SciTech Connect (OSTI)

    Lazarus, L.J.

    2000-09-25

    The objective of this task was to provide processing information data summaries on powder metallurgy (PM) alloys that meet the partner requirements for the production of low mass, highly accurate, near-net-shape powertrain components. This required modification to existing ISO machinability test procedures and development of a new drilling test procedure. These summaries could then be presented in a web page format. When combined with information generated from the USCAR CRADA this would allow chemical, metallurgical, and machining data on PM alloys to be available to all engineering and manufacturing personnel that have access to in-house networks. The web page format also allows for the additions of other wrought materials, making this a valuable tool to the technical staffs.

  5. Notice of Intent (NOI): Clean Energy Manufacturing Innovation Institute on

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Smart Manufacturing: Advanced Sensors, Controls, Platforms and Modeling for Manufacturing | Department of Energy Clean Energy Manufacturing Innovation Institute on Smart Manufacturing: Advanced Sensors, Controls, Platforms and Modeling for Manufacturing Notice of Intent (NOI): Clean Energy Manufacturing Innovation Institute on Smart Manufacturing: Advanced Sensors, Controls, Platforms and Modeling for Manufacturing December 11, 2014 - 11:30am Addthis The purpose of this Notice of Intent is

  6. Manufacturing Energy and Carbon Footprint Definitions and Assumptions...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Definitions and Assumptions, October 2012 Manufacturing Energy and Carbon Footprint ... More Documents & Publications Understanding Manufacturing Energy and Carbon Footprints, ...

  7. Advanced manufacturing: Technology and international competitiveness

    SciTech Connect (OSTI)

    Tesar, A.

    1995-02-01

    Dramatic changes in the competitiveness of German and Japanese manufacturing have been most evident since 1988. All three countries are now facing similar challenges, and these challenges are clearly observed in human capital issues. Our comparison of human capital issues in German, Japanese, and US manufacturing leads us to the following key judgments: Manufacturing workforces are undergoing significant changes due to advanced manufacturing technologies. As companies are forced to develop and apply these technologies, the constituency of the manufacturing workforce (especially educational requirements, contingent labor, job content, and continuing knowledge development) is being dramatically and irreversibly altered. The new workforce requirements which result due to advanced manufacturing require a higher level of worker sophistication and responsibility.

  8. Changing Global Petroleum Product Trade Flows

    U.S. Energy Information Administration (EIA) Indexed Site

    OECD/IEA 2014 © OECD/IEA 2014 Antoine Halff 2014 EIA Energy Conference Changing Global Petroleum Product Trade Flows Washington, DC July 14, 2014 © OECD/IEA 2014 Crude trade shifts further east  Asia imports increase by 2.6 mb/d to 22.1 mb, or 65% of the international crude market Crude Exports in 2019 and Growth in 2013-19 for Key Trade Routes 1 (million barrels per day) 0.2 0.3 (0) 2.0 (0.2) (-0.6) 4.1 (-0.6) 0.1 (-0.7) 3.1 1.2 (0.3) 1.0 (+0.1) -0.6 2.2 1.8 (+0.8) (-0.6) 1.1 (+0.3) Red

  9. Advanced Technology Vehicles Manufacturing Loan Program | Department of

    Energy Savers [EERE]

    of Energy Technology Vehicles Manufacturing Incentive Program Advanced Technology Vehicles Manufacturing Incentive Program A fact sheet detailling the advanced technology vehicles manufacturing incentive program. PDF icon Advanced Technology Vehicles Manufacturing Incentive Program More Documents & Publications Advanced Technology Vehicles Manufacturing Incentive Program MEMA: Comments MEMA: Letter Energy

    Technology Vehicles Manufacturing Loan Program Advanced Technology Vehicles

  10. Clean Energy Manufacturing Initiative: Increasing American Competitiveness

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Through Innovation | Department of Energy Manufacturing Initiative: Increasing American Competitiveness Through Innovation Clean Energy Manufacturing Initiative: Increasing American Competitiveness Through Innovation March 31, 2014 - 8:45pm Addthis Watch the video above to find out how private and public partnerships are critical to addressing the nation's energy challenges and expanding our clean energy economy. Manufacturing is making a resurgence in America. Companies such as Whirlpool -

  11. Clean Energy Manufacturing Reports | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Reports Clean Energy Manufacturing Reports The Clean Energy Manufacturing Initiative develops competitiveness analysis and strategies that inform R&D investments and other efforts needed to address key barriers to growing U.S. clean energy manufacturing competitiveness. This unprecedented competitiveness analysis evaluates the costs of producing clean energy products in the U.S. compared to competitor nations to understand factory location decisions and identify key drivers to U.S. clean

  12. Clean Energy Manufacturing Resources - Technology Feasibility | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Feasibility Clean Energy Manufacturing Resources - Technology Feasibility Clean Energy Manufacturing Resources - Technology Feasibility Find resources to help you evaluate the feasibility of your idea for a new clean energy technology or product. For determining feasibility, areas to consider include U.S. Department of Energy (DOE) priorities, licensing, R&D funding, and strategic project partnerships. For more resources, see the Clean Energy Manufacturing Federal Resource

  13. FACTSHEET: Next Generation Power Electronics Manufacturing Innovation

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Institute | Department of Energy Next Generation Power Electronics Manufacturing Innovation Institute FACTSHEET: Next Generation Power Electronics Manufacturing Innovation Institute January 15, 2014 - 9:20am Addthis The Obama Administration today announces the selection of North Carolina State University to lead a public-private manufacturing innovation institute for next generation power electronics. Supported by a $70 million Energy Department investment over five years as well as a

  14. National Electrical Manufacturers Association Comment | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Comment National Electrical Manufacturers Association Comment The National Electrical Manufacturers Association (NEMA) appreciates the opportunity to provide the attached comments on the Request for Information to Reduce Regulatory Burden as announced in the U.S. Federal Register Vol. 80, No. 127, beginning on page 38019. PDF icon Regulatory Burden RFI NEMA Comments regarding small motor regulations 17July2015 v5_1 More Documents & Publications National Electrical Manufacturers

  15. Advanced Blade Manufacturing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Blade Manufacturing Advanced Blade Manufacturing While the blades of a turbine may be one of the most recognizable features of any wind installation, they also represent one of the largest physical challenges in the manufacturing process. Turbine blades can reach up to 75 meters (250 feet) in length, and will continue to increase in size as the demand for renewable energy grows and as wind turbines are deployed offshore. Because of their size and aerodynamic complexity, wind turbine blades are

  16. Advanced Drivetrain Manufacturing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Drivetrain Manufacturing Advanced Drivetrain Manufacturing The U.S. Department of Energy (DOE) supports advanced manufacturing techniques that are leading to the "next-generation" of more reliable, affordable, and efficient wind turbine drivetrains. As turbines continue to increase in size, each and every component must also be scaled to meet the demands for renewable energy. What is the Drivetrain? The drivetrain of a wind turbine is composed of the gearbox and the generator, the

  17. Articles about Manufacturing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Manufacturing Articles about Manufacturing RSS Below are stories about manufacturing featured by the U.S. Department of Energy (DOE) Wind Program. September 17, 2015 Statistics Show Bearing Problems Cause the Majority of Wind Turbine Gearbox Failures In the past, the wind energy industry has been relatively conservative in terms of data sharing, especially with the general public, which has inhibited the research community's efforts to identify and mitigate the premature failures of wind turbine

  18. Agenda Advanced Methods for Manufacturing Workshop

    Energy Savers [EERE]

    Agenda Advanced Methods for Manufacturing Workshop September 29, 2015 Lockheed Martin 2021 Crystal Drive Arlington, Virginia 8:30 Safety, Security and Housekeeping Dr. Scott Anderson 8:45 - 10:45 2012 Projects, 30 minutes with questions Lockheed Martin - Direct manufacturing of Nuclear Power components EPRI - Innovative Manufacturing Process for Nuclear power Plant Components Purdue - Modular Connection Technologies for SC Walls INL - Monitoring and Control of Hybrid Laser-GMAW Process 10:45 -

  19. Project Profile: Improved Large Aperture Collector Manufacturing |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Concentrating Solar Power » Project Profile: Improved Large Aperture Collector Manufacturing Project Profile: Improved Large Aperture Collector Manufacturing Abengoa logo -- This project is inactive -- Abengoa Solar, under the Solar Manufacturing Technology (SolarMat) program, will be investigating the use of an automotive-style high-rate fabrication and automated assembly techniques to achieve a substantial reduction in the deployment cost of their new SpaceTube

  20. Revitalizing American Manufacturing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Revitalizing American Manufacturing Revitalizing American Manufacturing September 13, 2010 - 5:30pm Addthis A123 Systems' President David Vieau speaks with Energy Secretary Steven Chu and Michigan Governor Jennifer Granholm at the opening of their Livonia, MI plant. The plant will develop and manufacture advanced batteries systems for electric vehicles. | Department of Energy Photo | A123 Systems' President David Vieau speaks with Energy Secretary Steven Chu and Michigan Governor Jennifer

  1. Working with SRNL - The Advanced Manufacturing Collaborative

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4/2016 SEARCH SRNL GO The Advanced Manufacturing Collaborative Academia Government Industry AMC Leadership Contact AMC Home SRNL Home Working with SRNL The Advanced Manufacturing Collaborative For over 50 years, the Savannah River National Laboratory (SRNL) has been providing the science behind nuclear chemical manufacturing at the Savannah River Site (SRS), a sprawling nuclear complex that was once part of our nation's Cold War. Time has changed the mission at SRS from nuclear production for

  2. Advanced Qualification of Additive Manufacturing Workshop

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Additive Manufacturing Workshop Advanced Qualification of Additive Manufacturing Materials (AM) Workshop Our goal is to define opportunities and research gaps within additive manufacturing (AM) and to engage the broader scientific/engineering community to discuss future research directions. thumbnail of thumbnail of Contact Institute Director Dr. Alexander V. Balatsky Institute for Materials Science (505) 665-0077 Email Deputy Director Dr. Jennifer S. Martinez Institute for Materials Science

  3. Cincinnati Big Area Additive Manufacturing (BAAM)

    SciTech Connect (OSTI)

    Duty, Chad E.; Love, Lonnie J.

    2015-03-04

    Oak Ridge National Laboratory (ORNL) worked with Cincinnati Incorporated (CI) to demonstrate Big Area Additive Manufacturing which increases the speed of the additive manufacturing (AM) process by over 1000X, increases the size of parts by over 10X and shows a cost reduction of over 100X. ORNL worked with CI to transition the Big Area Additive Manufacturing (BAAM) technology from a proof-of-principle (TRL 2-3) demonstration to a prototype product stage (TRL 7-8).

  4. Canister storage building trade study. Final report

    SciTech Connect (OSTI)

    Swenson, C.E.

    1995-05-01

    This study was performed to evaluate the impact of several technical issues related to the usage of the Canister Storage Building (CSB) to safely stage and store N-Reactor spent fuel currently located at K-Basin 100KW and 100KE. Each technical issue formed the basis for an individual trade study used to develop the ROM cost and schedule estimates. The study used concept 2D from the Fluor prepared ``Staging and Storage Facility (SSF) Feasibility Report`` as the basis for development of the individual trade studies.

  5. International Trade of Wood Pellets (Brochure)

    SciTech Connect (OSTI)

    Not Available

    2013-05-01

    The production of wood pellets has increased dramatically in recent years due in large part to aggressive emissions policy in the European Union; the main markets that currently supply the European market are North America and Russia. However, current market circumstances and trade dynamics could change depending on the development of emerging markets, foreign exchange rates, and the evolution of carbon policies. This fact sheet outlines the existing and potential participants in the wood pellets market, along with historical data on production, trade, and prices.

  6. Changing Global Petroleum Product Trade Flows

    U.S. Energy Information Administration (EIA) Indexed Site

    Changing Global Petroleum Product Trade Flows For U.S. Energy Information Administration Conference July 14, 2014 | Washington, D.C. By Susan Grissom, U.S. Energy Information Administration In 2011, the U.S. became a net exporter of petroleum products Changing Global Petroleum Product Trade Flows, EIA Conference 2014 2 U.S. petroleum product imports and exports million barrels per day Source: EIA, Annual Energy Outlook 2014 Early Release -4 -3 -2 -1 0 1 2 3 4 1950 1960 1970 1980 1990 2000 2010

  7. Performance, Market and Manufacturing Constraints relevant to...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Performance, Market and Manufacturing Constraints relevant to the Industrialization of Thermoelectric Devices Market pricing of thermoelectric raw materials and processing, cost of ...

  8. National Network for Manufacturing Innovation: A Preliminary...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Resnick, Ralph, National Center for Manufacturing Sciences Rochester Regional Photonics Cluster Ruen Blanchard, Sarah, ASERTTI Salay, David, Ohio Aerospace Institute NAT I O NA L N ...

  9. Solar Manufacturing Technology 2 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    with Flextronics International USA, to deploy a fully integrated solar glass coating manufacturing line ... total energy yields from these panels enabling a significant reduction ...

  10. Integrated Design and Manufacturing of Thermoelectric Generator...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Thermoelectric Generator Using Thermal Spray Integrated Design and Manufacturing of Thermoelectric Generator Using Thermal Spray Presents progress in cost-effective thermoelectric ...

  11. PRESENTATION: BRIEFING ON CLEAN ENERGY MANUFACTURING

    Broader source: Energy.gov [DOE]

    A briefing to the Secretary's Energy Advisory Board on the clean energy manufacturing delivered by David Danielson, Assistant Secretary for Energy Efficiency and Renewable Energy.

  12. Fiber Reinforced Polymer Composite Manufacturing Workshop

    Broader source: Energy.gov [DOE]

    A workshop on Fiber Reinforced Polymer (FRP) Composite Manufacturing (held January 13, 2014, in Arlington, VA) brought together stakeholders from industry and academia to discuss manufacturing of composites. The workshop explored emerging FRP composite market applications in clean energy and barriers to the development and widespread commercial use of these lightweight, high-strength and high-stiffness materials. Improving the manufacturing speed and quality-and reducing their manufacturing costs-could accelerate their use in automotive, wind, compressed gas storage and other clean energy and industrial applications.

  13. Solid Oxide Fuel Cell Manufacturing Overview

    Broader source: Energy.gov [DOE]

    Presented at the NREL Hydrogen and Fuel Cell Manufacturing R&D Workshop in Washington, DC, August 11-12, 2011.

  14. Manufacturing Ecosystems and Keystone Technologies (Text Version)

    Broader source: Energy.gov [DOE]

    This is a text version of the Manufacturing Ecosystems and Keystone Technologies video, originally presented on March 12, 2012 at the MDF Workshop held in Chicago, Illinois.

  15. Dispatchable Distributed Generation: Manufacturing's Role in...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Manufacturing Presentation.pdf PDF icon Adams ERCOTDOE DER.PDF PDF icon WASHOM Austin ... 10 2016.pdf More Documents & Publications R&D For Dispatchable Distributed Energy ...

  16. Lessons Learned from the Photovoltaic Manufacturing Technology...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... yet be poised for actual manufacturing, to enter the field. ... in their technologies in terms of conversion efficiencies ... programmatic decisions and search for ways to minimize ...

  17. Clean Energy Manufacturing Initiative: Increasing American Competitive...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    These include: The SunShot Initiative's efforts to improve manufacturing of solar energy systems; The Wind Program's work on taller wind energy towers; and The Vehicle Technologies ...

  18. Solid State Lighting LED Manufacturing Roundtable Summary

    SciTech Connect (OSTI)

    none,

    2010-03-31

    Summary of a meeting of LED experts to develop proposed priority tasks for the Manufacturing R&D initiative, including task descriptions, discussion points, recommendations, and presentation highlights.

  19. LightManufacturing | Open Energy Information

    Open Energy Info (EERE)

    greenhouse gas emissions resulting from rotational molding. 6 Unlike concentrated solar power firms which focus on utility-scale electric production 7 , LightManufacturing...

  20. 2014 American Energy & Manufacturing Competitiveness Summit in...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Summit. Image: John Harrington, Council on Competitiveness 6 of 10 Local Motors CEO Jay Rogers demonstrates the 3D-printed car during the American Energy & Manufacturing...

  1. Microstructural Properties of Gamma Titanium Aluminide Manufactured...

    Office of Scientific and Technical Information (OSTI)

    COMPOUNDS In recent years, Electron Beam Melting (EBM) has matured as a technology for additive manufacturing of dense metal parts. The parts are built by additive consolidation...

  2. Clean Energy Manufacturing Initiative: Technology Research and...

    Energy Savers [EERE]

    manufacturers take advantage of this lower-priced fuel by modernizing the nations natural gas transmission and distribution systems and improving natural gas system efficiency....

  3. Solutia: Massachusetts Chemical Manufacturer Uses SECURE Methodology...

    Broader source: Energy.gov (indexed) [DOE]

    conducted at the Solutia Inc. chemical production facility in Springfield, Massachusetts. ... PDF icon Solutia: Massachusetts Chemical Manufacturer Uses SECURE Methodology to Identify ...

  4. Advanced Battery Manufacturing Facilities and Equipment Program...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Equipment Program Advanced Battery Manufacturing Facilities and Equipment Program AVTA: 2010 Honda Civic HEV with Experimental Ultra Lead Acid Battery Testing Results

  5. Microstructural Properties of Gamma Titanium Aluminide Manufactured...

    Office of Scientific and Technical Information (OSTI)

    Country of Publication: United States Language: English Subject: 36 MATERIALS SCIENCE; 71 ... GRAIN SIZE; MANUFACTURING; OXYGEN; TESTING; TITANIUM; TITANIUM COMPOUNDS Word Cloud ...

  6. Energy-Related Carbon Emissions in Manufacturing

    Reports and Publications (EIA)

    2000-01-01

    Energy-related carbon emissions in manufacturing analysis and issues related to the energy use, energy efficiency, and carbon emission indicators.

  7. 2014 Manufacturing Energy and Carbon Footprints: Definitions...

    Broader source: Energy.gov (indexed) [DOE]

    Definitions and Assumptions A number of key terms are used to interpret the manufacturing energy and carbon footprints. The terms associated with the energy footprint analysis are ...

  8. American Energy and Manufacturing Competitiveness Summit

    Broader source: Energy.gov [DOE]

    The American Energy and Manufacturing Competitiveness Summit will bring together leaders and perspectives from industry, government, academia, national laboratories, labor, and policy organizations...

  9. Smart Manufacturing Innovation Institute: Overview, Goals and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... o A manufacturing platform architecture, based on an open-standards, open- ... facilities Transition Plan o Sustainability plan for the proposed Institute past ...

  10. EI Summary of All Manufacturing SIC

    U.S. Energy Information Administration (EIA) Indexed Site

    try... Energy Consumption Use of Energy Electricity Manufacturing Floorspace Prices Energy Storage Energy and Operating Ratios Energy-Management Activities Technology...

  11. Advanced Manufacturing Office and Potential Technologies for...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    sustainability is improved in the making, use, and full lifecycle of the product made. ... Manufacturing Policy & DOE's Role * DOE ... End & What are the Metrics for This ...

  12. Advanced Manufacturing Office Small Business Innovation Research...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Manufacturing Office Small Business Innovation Research Small Business Technology ... in thermal and degradation resistance, high-performance, and lower-cost for energy systems. ...

  13. Manufacturing Success Stories | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Advanced Manufacturing Office; John Dennis, Mayor of West Lafayette; Mitch Daniels, President of Purdue University; R. Byron Pipes, John Leighton Bray Distinguished...

  14. 2010 Manufacturing Energy and Carbon Footprints: Definitions...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (MECS 2010) More Documents & Publications U.S. Manufacturing Energy Use and Greenhouse Gas Emissions Analysis MECS 2006 - Computer, Electronics and Appliances MECS 2006 - Cement

  15. Oak Ridge Centers for Manufacturing Technology - Partnership...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    with some of the people who experienced the Oak Ridge Centers for Manufacturing Technology firsthand. Here is his introduction followed by the first of three letters...

  16. FACTSHEET: Next Generation Power Electronics Manufacturing Innovation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    manufacturing innovation institute for next ... 70 million in non-federal cost-share, the institute will ... - ultimately helping to lower the cost of electricity and ...

  17. Low Energy Ion Implantationin Semiconductor Manufacturing | U...

    Office of Science (SC) Website

    Low Energy Ion Implantation in Semiconductor Manufacturing Nuclear Physics (NP) NP Home ... Contact Information Nuclear Physics U.S. Department of Energy SC-26Germantown Building ...

  18. Manufacturing Energy and Carbon Footprint References

    Broader source: Energy.gov (indexed) [DOE]

    References AMO (Advanced Manufacturing Office), EERE (Energy Efficiency and Renewable Energy). 2012. Consider Installing High-Pressure Boilers with Backpressure Turbine-Generators. ...

  19. Battery Manufacturing Processes Improved by Johnson Controls...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Johnson Controls Project Improving battery manufacturing processes can help make plug-in electric vehicles more affordable and convenient. This will help meet the government's EV...

  20. Oak Ridge Centers for Manufacturing Technology ? testimonials

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    testimonials The first testimonial for the successful Oak Ridge Centers for Manufacturing Technology came from Mitchell Burnett. Mitch was among the first hourly paid employees, an...

  1. Advanced Manufacturing Office | Department of Energy

    Energy Savers [EERE]

    Advanced Manufacturing Office ISO 50001SEP Pilot Program - Applications Due 182016 ISO 50001SEP Pilot Program - Applications Due 182016 The U.S. DOE invites applications for...

  2. Fiber Reinforced Polymer Composite Manufacturing Workshop | Department...

    Broader source: Energy.gov (indexed) [DOE]

    A workshop on Fiber Reinforced Polymer (FRP) Composite Manufacturing (held January 13, 2014, in Arlington, VA) brought together stakeholders from industry and academia to discuss...

  3. Institute for Advanced Composites Manufacturing Innovation Holds...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... of Energy Advanced Manufacturing Office; John Dennis, Mayor of West Lafayette; Mitch Daniels, President of Purdue University; R. Byron Pipes, John Leighton Bray Distinguished ...

  4. 2015 American Energy and Manufacturing Competitiveness Summit

    Broader source: Energy.gov [DOE]

    The 2015 American Energy & Manufacturing Competitiveness (AEMC) Summit is a gathering of preeminent leaders from industry, academia, labor, the national laboratories, government and media to:

  5. Manufacturing Barriers to High Temperature PEM Commercialization

    Broader source: Energy.gov [DOE]

    Presented at the NREL Hydrogen and Fuel Cell Manufacturing R&D Workshop in Washington, DC, August 11-12, 2011.

  6. Bandwidth Study U.S. Chemical Manufacturing

    Broader source: Energy.gov [DOE]

    Energy bandwidth studies of U.S. manufacturing sectors can serve as foundational references in framing the range (or bandwidth) of potential energy savings opportunities. This bandwidth study...

  7. Derived Annual Estimates of Manufacturing Energy Consumption...

    U.S. Energy Information Administration (EIA) Indexed Site

    > Derived Annual Estimates - Executive Summary Derived Annual Estimates of Manufacturing Energy Consumption, 1974-1988 Figure showing Derived Estimates Executive Summary This...

  8. Composite Tube Trailer Design/Manufacturing Needs

    Broader source: Energy.gov [DOE]

    Presented at the NREL Hydrogen and Fuel Cell Manufacturing R&D Workshop in Washington, DC, August 11-12, 2011.

  9. Low Temperature PEM Fuel Cell Manufacturing Needs

    Broader source: Energy.gov [DOE]

    Presented at the NREL Hydrogen and Fuel Cell Manufacturing R&D Workshop in Washington, DC, August 11-12, 2011.

  10. Electric Drive Component Manufacturing Facilities | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Electric Drive Component Manufacturing Facilities Technology Roadmap Analysis 2013: Assessing Automotive Technology R&D Relevant to DOE Power Electronics Cost Targets Advanced ...

  11. Welcome and Advanced Manufacturing Partnership (Text Version)

    Broader source: Energy.gov [DOE]

    This is a text version of the Welcome and Advanced Manufacturing Partnership video, originally presented on March 12, 2012 at the MDF Workshop held in Chicago, Illinois.

  12. Energy futures: Trading opportunities for the 1990s

    SciTech Connect (OSTI)

    Treat, J.E.

    1990-01-01

    This volume contains an edited collection of views from practitioners in the rapidly growing area of energy futures and options trading, a major element of risk management. Four chapters are devoted to Trading Theories and Strategies. This section is aimed at the specialist in energy, rather than finance. The complexities of options trading are described in another chapter. The remaining sections of this book present a variety of topics in this field including Natural Gas Trading and Futures, Energy Futures and Options Trading, and Accounting, Taxation and Internal Control. The book is a good introduction and reference to the mechanics and institutions of energy futures contracts and trading.

  13. Westinghouse receives high marks for management, operation of WIPP

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Receives High Marks For Management, Operation of WIPP CARLSBAD, N.M., January 11, 2000 - The Westinghouse Waste Isolation Division (WID) received high marks from the U.S. Department of Energy (DOE) for its management and operation of the Waste Isolation Pilot Plant (WIPP) in fiscal year 1999. For the 12-month performance evaluation period from October 1, 1998 through September 30, 1999, Westinghouse received 94.9 of a possible 100 points. The DOE considers a score of 86 to 95 as good. A score

  14. Diesel prices dip below the 4 dollar mark

    U.S. Energy Information Administration (EIA) Indexed Site

    Diesel prices dip below the 4 dollar mark The U.S. average retail price for on-highway diesel fuel dipped below the 4-dollar mark for the first time since late January to $3.99 a gallon on Monday. That's down 1.3 cents from a week ago, based on the weekly price survey by the U.S. Energy Information Administration. Diesel prices were highest in the New England region at 4.15 a gallon, down 2.3 cents from a week ago. Prices were lowest in the Gulf Coast region at 3.92 a gallon, down 2 cents. This

  15. SRS Recovery Act Program Reaches $1 Billion Mark: Investments Accelerate

    Energy Savers [EERE]

    Cleanup; Support Jobs, Training and Local Economy | Department of Energy Recovery Act Program Reaches $1 Billion Mark: Investments Accelerate Cleanup; Support Jobs, Training and Local Economy SRS Recovery Act Program Reaches $1 Billion Mark: Investments Accelerate Cleanup; Support Jobs, Training and Local Economy March 2, 2011 - 12:00pm Addthis Media Contacts Jim Giusti, DOE (803) 952-7697 james-r.giusti@srs.gov Paivi Nettamo, SRNS (803) 292-2484 paivi.nettamo@srs.gov John Lindsay, SRR (803)

  16. Caribbean LNG project marks progress; LNG tanker launched

    SciTech Connect (OSTI)

    1997-10-20

    World LNG trade continues to expand as construction of a major LNG project in the Caribbean hits full stride this fall and another LNG carrier was launched earlier this year. Engineering is nearly complete and construction is nearing midway on Trinidad`s Atlantic LNG. In Japan, NKK Corp. launched another LNG tanker that employs the membrane-storage system. The 50-mile pipeline to move natural gas to the Atlantic LNG facility is also on track for completion by October 1998.

  17. Electric trade in the United States 1992

    SciTech Connect (OSTI)

    Not Available

    1994-09-01

    This publication, Electric Trade in the US 1992 (ELECTRA), is the fourth in a series of reports on wholesale power transactions prepared by the Electric Data Systems Branch, Survey Management Division, Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA). The electric trade data are published biennially. The first report presented 1986 data, and this report provides information on the electric power industry during 1992. The electric trade data collected and presented in this report furnish important information on the wholesale structure found within the US electric power industry. The patterns of interutility trade in the report support analyses of wholesale power transactions and provide input for a broader understanding of bulk power market issues that define the emerging national electric energy policies. The report includes information on the quantity of power purchased, sold, exchanged, and wheeled; the geographical locations of transactions and ownership classes involved; and the revenues and costs. Information on the physical transmission system are being included for the first time in this publication. Transmission data covering investor-owned electric utilities were shifted from the Financial Statistics of Selected Investor-Owned Electric Utilities to the ELECTRA publication. Some of the prominent features of this year`s report include information and data not published before on transmission lines for publicly owned utilities and transmission lines added during 1992 by investor-owned electric utilities.

  18. Smart Manufacturing Institute Industry Day Workshop Proceedings

    Broader source: Energy.gov [DOE]

    AMO hosted an Industry Day workshop to explain the concept, vision, and technology needs associated with support for a Clean Energy Manufacturing Innovation Institute on Smart Manufacturing. The workshop was held on February 25, 2015 at the Georgia Tech Hotel & Conference Center in Atlanta, GA.

  19. Clean Energy Manufacturing Resources - Technology Maturation | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Maturation Clean Energy Manufacturing Resources - Technology Maturation Clean Energy Manufacturing Resources - Technology Maturation Find resources to help you commercialize and market your clean energy technology or product. For technology maturation, areas to consider include regulations and standards; exporting; product testing or demonstration; energy-efficient product qualifications; and energy efficiency and performance improvements for plants. For more resources, see the

  20. ITP Nanomanufacturing: Nanomanufacturing Portfolio: Manufacturing Processes

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Applications to Accelerate Commercial Use of Nanomaterials, January 2011 | Department of Energy Nanomanufacturing: Nanomanufacturing Portfolio: Manufacturing Processes and Applications to Accelerate Commercial Use of Nanomaterials, January 2011 ITP Nanomanufacturing: Nanomanufacturing Portfolio: Manufacturing Processes and Applications to Accelerate Commercial Use of Nanomaterials, January 2011 PDF icon nanomanufacturing_portfolio.pdf More Documents & Publications Sustainable

  1. Innovative Manufacturing Initiative Recognition Day - Final Participant

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Listing | Department of Energy Day - Final Participant Listing Innovative Manufacturing Initiative Recognition Day - Final Participant Listing PDF icon imi_recogitionday_participants.pdf More Documents & Publications Innovative Manufacturing Initiative Recognition Day 2015 AMO Peer Review Agenda CX-100154 Categorical Exclusion Determination

  2. Duracold Refrigeration Manufacturing: Order (2013-CE-5342)

    Broader source: Energy.gov [DOE]

    DOE ordered Duracold Refrigeration Manufacturing Company, LLC to pay a $8,000 civil penalty after finding Duracold Refrigeration Manufacturing had failed to certify that certain models of walk-in cooler and freezer components comply with the applicable energy conservation standards.

  3. Clean Energy Manufacturing Analysis Center (CEMAC)

    SciTech Connect (OSTI)

    2015-12-01

    The U.S. Department of Energy's Clean Energy Manufacturing Analysis Center (CEMAC) provides objective analysis and up-to-date data on global supply chains and manufacturing of clean energy technologies. Policymakers and industry leaders seek CEMAC insights to inform choices to promote economic growth and the transition to a clean energy economy.

  4. Photonic crystal scintillators and methods of manufacture

    DOE Patents [OSTI]

    Torres, Ricardo D.; Sexton, Lindsay T.; Fuentes, Roderick E.; Cortes-Concepcion, Jose

    2015-08-11

    Photonic crystal scintillators and their methods of manufacture are provided. Exemplary methods of manufacture include using a highly-ordered porous anodic alumina membrane as a pattern transfer mask for either the etching of underlying material or for the deposition of additional material onto the surface of a scintillator. Exemplary detectors utilizing such photonic crystal scintillators are also provided.

  5. additive manufacturing | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Home additive manufacturing LLNL researchers outline what happens during metal 3D printing, enhancing confidence From left, Lawrence Livermore National Laboratory researchers Ibo Matthews, a principal investigator leading the lab's effort on the joint open source software project; Wayne King, director of the Accelerated Certification of Additively Manufactured Metals Initiative; and Gabe Guss, engineering...

  6. EA-250 PSEG Energy Resources & Trade LLC | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PDF icon EA-250 PSEG Energy Resources & Trade LLC More Documents & Publications Ea-168-A PG&E Energy Trading-Power, L.P EA-196-A Minnesota Power, Sales EA-220-A NRG Power ...

  7. SPR Awards Exchange Contract to Shell Trading | Department of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Awards Exchange Contract to Shell Trading SPR Awards Exchange Contract to Shell Trading May 10, 2007 - 12:55pm Addthis Deliveries to Begin in August WASHINGTON, DC - The U.S. ...

  8. EA-365-A Centre Lane Trading Limited | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    -A Centre Lane Trading Limited EA-365-A Centre Lane Trading Limited Order authorizing CLT to export electric energy to Canada. PDF icon EA-365-A Centre Lane (CN).pdf More Documents ...

  9. Vis Nova Trading GmbH | Open Energy Information

    Open Energy Info (EERE)

    Nova Trading GmbH Jump to: navigation, search Name: Vis Nova Trading GmbH Place: Bremen, Germany Zip: 28217 Product: Germany-based producer and trader of wood pellets....

  10. Small Business Award to Sage Energy Trading Download | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Award to Sage Energy Trading Download Small Business Award to Sage Energy Trading Download View official release document by clicking the link below. PDF icon Small-Business-Award-...

  11. Clean Energy Manufacturing Funding Opportunities | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Funding Opportunities Clean Energy Manufacturing Funding Opportunities To accomplish the goals of the Clean Energy Manufacturing Initiative (CEMI), the U.S. Department of Energy (DOE) supports increased funding for manufacturing research and development across the board, specifically with the goal of growing the clean energy manufacturing industry in the United States. Examples include: Photo of carbon fiber rolls being manufactured. Solar Manufacturing Technology Solar Manufacturing Technology

  12. Understanding the 2014 Manufacturing Energy and Carbon Footprints

    Energy Savers [EERE]

    Understanding the 2010 Manufacturing Energy and Carbon Footprints The Manufacturing Energy and Carbon Footprints map energy use and combustion greenhouse gas (GHG) emissions from energy supply to end use. Footprints are published for 15 manufacturing sectors (representing 95% of all manufacturing energy use and 94% of U.S. manufacturing combustion GHG emissions) and for U.S. manufacturing as a whole (NAICS 31 - 33). These sectors are described in more detail in the document 2010 Manufacturing

  13. Static Sankey Diagram Full Sector Manufacturing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Full Sector Manufacturing Static Sankey Diagram Full Sector Manufacturing The U.S. Manufacturing Sector Static Sankey diagram shows how total primary energy is used by U.S. manufacturing plants. Click on the Onsite Generation, Process Energy or Nonprocess Energy thumbnails below the diagram to see further detail on energy flows in manufacturing. Also, see the Dynamic Manufacturing Energy Sankey Tool to pan, zoom, and customize the manufacturing Sankey data and compare energy consumption across

  14. Manufacturing fuel-switching capability, 1988

    SciTech Connect (OSTI)

    Not Available

    1991-09-01

    Historically, about one-third of all energy consumed in the United States has been used by manufacturers. About one-quarter of manufacturing energy is used as feedstocks and raw material inputs that are converted into nonenergy products; the remainder is used for its energy content. During 1988, the most recent year for which data are available, manufacturers consumed 15.5 quadrillion British thermal units (Btu) of energy to produce heat and power and to generate electricity. The manufacturing sector also has widespread capabilities to switch from one fuel to another for either economic or emergency reasons. There are numerous ways to define fuel switching. For the purposes of the Manufacturing Energy Consumption Survey (MECS), fuel switching is defined as the capability to substitute one energy source for another within 30 days with no significant modifications to the fuel-consuming equipment, while keeping production constant. Fuel-switching capability allows manufacturers substantial flexibility in choosing their mix of energy sources. The consumption of a given energy source can be maximized if all possible switching into that energy source takes place. The estimates in this report are based on data collected on the 1988 Manufacturing Energy Consumption Survey (MECS), Forms 846 (A through C). The EIA conducts this national sample survey of manufacturing energy consumption on a triennial basis. The MECS is the only comprehensive source of national-level data on energy-related information for the manufacturing industries. The MECS was first conducted in 1986 to collect data for 1985. This report presents information on the fuel-switching capabilities of manufacturers in 1988. This report is the second of a series based on the 1988 MECS. 8 figs., 31 tabs.

  15. DOE GC Joins Customs Service Trade Data System to Strengthen...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of its energy conservation regulations thus ensuring that foreign manufacturers have to follow the same rules as domestic manufacturers. DOE and Customs are also working to...

  16. Political Economy of Brazilian foreign policy: nuclear energy, trade, and Itaipu

    SciTech Connect (OSTI)

    Soares de Lima, M.R.

    1986-01-01

    This dissertation advances an analytical framework intended to account for the international strategies of semi-peripheral countries: those industrialized Third World countries able to manufacture and export industrial goods. The empirical validation of the proposed framework was assessed through five case studies of Brazil's conduct in the following issue areas: nuclear energy, trade, and hydroelectric development of the Parana River Basin. A free-rider strategy was observed in the case of the nonproliferation regime. The decision to attain nuclear self sufficiency through the 1975 agreement with West Germany conforms to what was defined as unilateral behavior. Brazil's activism on behalf of Third World demands in North South negotiations as they impinge upon trade matters was accounted for in terms of the existence of private gains accruing from participation in that collective endeavor. Compliance with a regime's rules resulting from the use or threat of use of coercion was observed in the case of multilateral trade negotiations. The last case study examines a pattern of behavior defined as a hegemonic. In the development of a regime for the utilization of the Parana River Basin's hydroelectric potential, Brazil provided positive incentives to its junior partner (Paraguay) and negative inducements to the uncooperative partner (Argentina).

  17. North America: Regulation of International Electricity Trade | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy America: Regulation of International Electricity Trade North America: Regulation of International Electricity Trade North America: Regulation of International Electricity Trade prepared by North American Energy Working Group on December 2002. PDF icon North America: Regulation of International Electricity Trade More Documents & Publications Regulatory Side-by-Side Governing Permitting of Cross-Border Electricity Transmission Facilities Between the United States and Canada Guide

  18. Utility of Big Area Additive Manufacturing (BAAM) For The Rapid Manufacture of Customized Electric Vehicles

    SciTech Connect (OSTI)

    Love, Lonnie J.

    2015-08-01

    This Oak Ridge National Laboratory (ORNL) Manufacturing Development Facility (MDF) technical collaboration project was conducted in two phases as a CRADA with Local Motors Inc. Phase 1 was previously reported as Advanced Manufacturing of Complex Cyber Mechanical Devices through Community Engagement and Micro-manufacturing and demonstrated the integration of components onto a prototype body part for a vehicle. Phase 2 was reported as Utility of Big Area Additive Manufacturing (BAAM) for the Rapid Manufacture of Customized Electric Vehicles and demonstrated the high profile live printing of an all-electric vehicle using ONRL s Big Area Additive Manufacturing (BAAM) technology. This demonstration generated considerable national attention and successfully demonstrated the capabilities of the BAAM system as developed by ORNL and Cincinnati, Inc. and the feasibility of additive manufacturing of a full scale electric vehicle as envisioned by the CRADA partner Local Motors, Inc.

  19. DOE CMPC Marking Resource | OSTI, US Dept of Energy, Office of...

    Office of Scientific and Technical Information (OSTI)

    CMPC Marking Resource Printer-friendly version Printer-friendly version Document Info Available Downloads for this Document: applicationpdf icon OSTI Copy of DOE CMPC Marking ...

  20. A National Strategic Plan For Advanced Manufacturing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    A National Strategic Plan For Advanced Manufacturing A National Strategic Plan For Advanced Manufacturing PDF icon nstc_feb2012.pdf More Documents & Publications Report to the President on Ensuring American Leadership in Advanced Manufacturing National Network for Manufacturing Innovation: A Preliminary Design National Network for Manufacturing Innovation: A Preliminary Design