National Library of Energy BETA

Sample records for tracking-flat plate thin-film

  1. Annual collectible energy of a two-axis tracking flat-plate solar collector

    SciTech Connect (OSTI)

    Attalage, R.A.; Reddy, T.A. )

    1992-01-01

    A correlation for annual collectible energy of a two-axis tracking flat-plate solar collector has been developed using simulated results based on typical meteorological year (TMY) data for 26 US locations. A preliminary validation of this correlation has been carried out with data from four Australian locations. With the advent of increasing interest in photovoltaic systems, there are a number of advantages of using a two-axis flat-plate collector. Since the tracking system is generally much cheaper than the collector panel, such a mode permits the incident solar radiation to be collected more efficiently. Incidence angle effects are minimized and, moreover, contrary to concentrating collectors, such a mode enables both the diffuse and beam components of solar radiation to be collected. In tropical locations where the diffuse fraction is generally high, this may be a great advantage. The objective of this study was to develop a correlation for the annual collectible energy of a two-axis tracking flat-plate collector.

  2. Thin-film flat-plate solar collectors for low-cost manufacture and installation

    SciTech Connect (OSTI)

    Andrews, J.W.; Wilhelm, W.G.

    1980-03-01

    A flat-plate solar energy collector design using thin-film plastics in both the absorber and glazing is described. The design approach proceeded in two steps. First, cost constraints on solar collectors were determined using reasonable economic projections. Second, engineering was applied only to those ideas which had hope of falling within those cost boundaries. The use of thin-film plastics appeared most attractive according to these criteria. The nature of the marketing and distribution network can be expected to have a strong impact on the final installed cost of the collector; the proposed design has characteristics which could make possible a reduced price markup.

  3. Effects of low temperature annealing on the adhesion of electroless plated copper thin films in TiN deposited silicon integrated circuit substrates 

    E-Print Network [OSTI]

    Tate, Adam Timothy

    2013-02-22

    ], (These tests have been used to determine the adhesion of a variety of materials, not only thin films. ) While many tests exist and have been employed to make qualitative comparisons of adhesion strengths, little quantitative data on thin fil adhesion... It has been demonstrated that an anneal following metal deposition results in improved adhesion of the metal thin film to the substrate [2]. Both low temperature and high temperature anneals can be performed to improve the adhesion of a copper fil...

  4. Thin film hydrogen sensor

    DOE Patents [OSTI]

    Cheng, Y.T.; Poli, A.A.; Meltser, M.A.

    1999-03-23

    A thin film hydrogen sensor includes a substantially flat ceramic substrate with first and second planar sides and a first substrate end opposite a second substrate end; a thin film temperature responsive resistor on the first planar side of the substrate proximate to the first substrate end; a thin film hydrogen responsive metal resistor on the first planar side of the substrate proximate to the fist substrate end and proximate to the temperature responsive resistor; and a heater on the second planar side of the substrate proximate to the first end. 5 figs.

  5. Thin film hydrogen sensor

    DOE Patents [OSTI]

    Cheng, Yang-Tse (Rochester Hills, MI); Poli, Andrea A. (Livonia, MI); Meltser, Mark Alexander (Pittsford, NY)

    1999-01-01

    A thin film hydrogen sensor, includes: a substantially flat ceramic substrate with first and second planar sides and a first substrate end opposite a second substrate end; a thin film temperature responsive resistor on the first planar side of the substrate proximate to the first substrate end; a thin film hydrogen responsive metal resistor on the first planar side of the substrate proximate to the fist substrate end and proximate to the temperature responsive resistor; and a heater on the second planar side of the substrate proximate to the first end.

  6. Multifunctional thin film surface

    DOE Patents [OSTI]

    Brozik, Susan M.; Harper, Jason C.; Polsky, Ronen; Wheeler, David R.; Arango, Dulce C.; Dirk, Shawn M.

    2015-10-13

    A thin film with multiple binding functionality can be prepared on an electrode surface via consecutive electroreduction of two or more aryl-onium salts with different functional groups. This versatile and simple method for forming multifunctional surfaces provides an effective means for immobilization of diverse molecules at close proximities. The multifunctional thin film has applications in bioelectronics, molecular electronics, clinical diagnostics, and chemical and biological sensing.

  7. Synthesis and characterization of high power LiFePO4/C nano-plate thin films Nan Zhou a,b

    E-Print Network [OSTI]

    Cao, Guozhong

    years to accommodate our increasingly mobile and technology driven society [1]. These batteries exhibit of Applied Chemistry, Beijing Institute of Petrochemical Technology, Beijing 102617, China a r t i c l e i n battery Solvothermal growth Nano-carbon coating a b s t r a c t Tunable LiFePO4/C thin films demonstrating

  8. NMR characterization of thin films

    DOE Patents [OSTI]

    Gerald, II, Rex E. (Brookfield, IL); Klingler, Robert J. (Glenview, IL); Rathke, Jerome W. (Homer Glen, IL); Diaz, Rocio (Chicago, IL); Vukovic, Lela (Westchester, IL)

    2008-11-25

    A method, apparatus, and system for characterizing thin film materials. The method, apparatus, and system includes a container for receiving a starting material, applying a gravitational force, a magnetic force, and an electric force or combinations thereof to at least the starting material, forming a thin film material, sensing an NMR signal from the thin film material and analyzing the NMR signal to characterize the thin film of material.

  9. NMR characterization of thin films

    DOE Patents [OSTI]

    Gerald II, Rex E.; Klingler, Robert J.; Rathke, Jerome W.; Diaz, Rocio; Vukovic, Lela

    2010-06-15

    A method, apparatus, and system for characterizing thin film materials. The method, apparatus, and system includes a container for receiving a starting material, applying a gravitational force, a magnetic force, and an electric force or combinations thereof to at least the starting material, forming a thin film material, sensing an NMR signal from the thin film material and analyzing the NMR signal to characterize the thin film of material.

  10. Epitaxial thin films

    DOE Patents [OSTI]

    Hunt, Andrew Tye; Deshpande, Girish; Lin, Wen-Yi; Jan, Tzyy-Jiuan

    2006-04-25

    Epitatial thin films for use as buffer layers for high temperature superconductors, electrolytes in solid oxide fuel cells (SOFC), gas separation membranes or dielectric material in electronic devices, are disclosed. By using CCVD, CACVD or any other suitable deposition process, epitaxial films having pore-free, ideal grain boundaries, and dense structure can be formed. Several different types of materials are disclosed for use as buffer layers in high temperature superconductors. In addition, the use of epitaxial thin films for electrolytes and electrode formation in SOFCs results in densification for pore-free and ideal gain boundary/interface microstructure. Gas separation membranes for the production of oxygen and hydrogen are also disclosed. These semipermeable membranes are formed by high-quality, dense, gas-tight, pinhole free sub-micro scale layers of mixed-conducting oxides on porous ceramic substrates. Epitaxial thin films as dielectric material in capacitors are also taught herein. Capacitors are utilized according to their capacitance values which are dependent on their physical structure and dielectric permittivity. The epitaxial thin films of the current invention form low-loss dielectric layers with extremely high permittivity. This high permittivity allows for the formation of capacitors that can have their capacitance adjusted by applying a DC bias between their electrodes.

  11. Thin film photovoltaic cell

    DOE Patents [OSTI]

    Meakin, John D. (Newark, DE); Bragagnolo, Julio (Newark, DE)

    1982-01-01

    A thin film photovoltaic cell having a transparent electrical contact and an opaque electrical contact with a pair of semiconductors therebetween includes utilizing one of the electrical contacts as a substrate and wherein the inner surface thereof is modified by microroughening while being macro-planar.

  12. Thin film superconductor magnetic bearings

    DOE Patents [OSTI]

    Weinberger, Bernard R. (Avon, CT)

    1995-12-26

    A superconductor magnetic bearing includes a shaft (10) that is subject to a load (L) and rotatable around an axis of rotation, a magnet (12) mounted to the shaft, and a stator (14) in proximity to the shaft. The stator (14) has a superconductor thin film assembly (16) positioned to interact with the magnet (12) to produce a levitation force on the shaft (10) that supports the load (L). The thin film assembly (16) includes at least two superconductor thin films (18) and at least one substrate (20). Each thin film (18) is positioned on a substrate (20) and all the thin films are positioned such that an applied magnetic field from the magnet (12) passes through all the thin films. A similar bearing in which the thin film assembly (16) is mounted on the shaft (10) and the magnet (12) is part of the stator (14) also can be constructed.

  13. Modeling and control of thin film surface morphology: application to thin film solar cells

    E-Print Network [OSTI]

    Huang, Jianqiao

    2012-01-01

    151 Two-stage thin film deposition process15 Description of thin film depositionProcess Model . . . . 54 Porous Thin-Film Deposition Process

  14. Laser Induced Breakdown Spectroscopy and Applications Toward Thin Film Analysis

    E-Print Network [OSTI]

    Owens, Travis Nathan

    2011-01-01

    Organic Thin Films 4.1 Introduction . . . . . . . . . . . .T iO 2 thin films. . . . . . . . . . . . . . . . . . . . .properties of the organic thin films. . . . . . . . .

  15. Thin film composite electrolyte

    DOE Patents [OSTI]

    Schucker, Robert C. (The Woodlands, TX)

    2007-08-14

    The invention is a thin film composite solid (and a means for making such) suitable for use as an electrolyte, having a first layer of a dense, non-porous conductive material; a second layer of a porous ionic conductive material; and a third layer of a dense non-porous conductive material, wherein the second layer has a Coefficient of thermal expansion within 5% of the coefficient of thermal expansion of the first and third layers.

  16. Thin film photovoltaic device

    DOE Patents [OSTI]

    Catalano, A.W.; Bhushan, M.

    1982-08-03

    A thin film photovoltaic solar cell which utilizes a zinc phosphide semiconductor is of the homojunction type comprising an n-type conductivity region forming an electrical junction with a p-type region, both regions consisting essentially of the same semiconductor material. The n-type region is formed by treating zinc phosphide with an extrinsic dopant such as magnesium. The semiconductor is formed on a multilayer substrate which acts as an opaque contact. Various transparent contacts may be used, including a thin metal film of the same chemical composition as the n-type dopant or conductive oxides or metal grids. 5 figs.

  17. Thin film hydrogen sensor

    DOE Patents [OSTI]

    Lauf, Robert J. (Oak Ridge, TN); Hoffheins, Barbara S. (Knoxville, TN); Fleming, Pamela H. (Oak Ridge, TN)

    1994-01-01

    A hydrogen sensor element comprises an essentially inert, electrically-insulating substrate having a thin-film metallization deposited thereon which forms at least two resistors on the substrate. The metallization comprises a layer of Pd or a Pd alloy for sensing hydrogen and an underlying intermediate metal layer for providing enhanced adhesion of the metallization to the substrate. An essentially inert, electrically insulating, hydrogen impermeable passivation layer covers at least one of the resistors, and at least one of the resistors is left uncovered. The difference in electrical resistances of the covered resistor and the uncovered resistor is related to hydrogen concentration in a gas to which the sensor element is exposed.

  18. Thin film photovoltaic device

    DOE Patents [OSTI]

    Catalano, Anthony W. (Wilmington, DE); Bhushan, Manjul (Wilmington, DE)

    1982-01-01

    A thin film photovoltaic solar cell which utilizes a zinc phosphide semiconductor is of the homojunction type comprising an n-type conductivity region forming an electrical junction with a p-type region, both regions consisting essentially of the same semiconductor material. The n-type region is formed by treating zinc phosphide with an extrinsic dopant such as magnesium. The semiconductor is formed on a multilayer substrate which acts as an opaque contact. Various transparent contacts may be used, including a thin metal film of the same chemical composition as the n-type dopant or conductive oxides or metal grids.

  19. Thin film ion conducting coating

    DOE Patents [OSTI]

    Goldner, Ronald B. (Lexington, MA); Haas, Terry (Sudbury, MA); Wong, Kwok-Keung (Watertown, MA); Seward, George (Arlington, MA)

    1989-01-01

    Durable thin film ion conducting coatings are formed on a transparent glass substrate by the controlled deposition of the mixed oxides of lithium:tantalum or lithium:niobium. The coatings provide durable ion transport sources for thin film solid state storage batteries and electrochromic energy conservation devices.

  20. Thin film hydrogen sensor

    DOE Patents [OSTI]

    Lauf, R.J.; Hoffheins, B.S.; Fleming, P.H.

    1994-11-22

    A hydrogen sensor element comprises an essentially inert, electrically-insulating substrate having a thin-film metallization deposited thereon which forms at least two resistors on the substrate. The metallization comprises a layer of Pd or a Pd alloy for sensing hydrogen and an underlying intermediate metal layer for providing enhanced adhesion of the metallization to the substrate. An essentially inert, electrically insulating, hydrogen impermeable passivation layer covers at least one of the resistors, and at least one of the resistors is left uncovered. The difference in electrical resistances of the covered resistor and the uncovered resistor is related to hydrogen concentration in a gas to which the sensor element is exposed. 6 figs.

  1. Vertically Aligned Nanocomposite Thin Films 

    E-Print Network [OSTI]

    Bi, Zhenxing

    2012-07-16

    and epitaxial growth ability on given substrates. In the present work, we investigated unique epitaxial two-phase VAN (BiFeO3)x:(Sm2O3)1-x and (La0.7Sr0.3MnO3)x:(Mn3O4)1-x thin film systems by pulsed laser deposition. These VAN thin films exhibit a highly...

  2. Modeling and control of thin film surface morphology: application to thin film solar cells

    E-Print Network [OSTI]

    Huang, Jianqiao

    2012-01-01

    of a p-i-n thin-film solar cell with front transparent con-for thin-film a-si:h solar cells. Progress in Photovoltaics,in thin-film silicon solar cells. Optics Communications,

  3. Modeling and control of thin film surface morphology: application to thin film solar cells

    E-Print Network [OSTI]

    Huang, Jianqiao

    2012-01-01

    microcrystalline silicon thin films and solar cells. Journalof a p-i-n thin-film solar cell with front transparent con-microcrystalline silicon thin film solar cells. Solar Energy

  4. Low work function, stable thin films

    DOE Patents [OSTI]

    Dinh, Long N. (Concord, CA); McLean, II, William (Oakland, CA); Balooch, Mehdi (Berkeley, CA); Fehring, Jr., Edward J. (Dublin, CA); Schildbach, Marcus A. (Livermore, CA)

    2000-01-01

    Generation of low work function, stable compound thin films by laser ablation. Compound thin films with low work function can be synthesized by simultaneously laser ablating silicon, for example, and thermal evaporating an alkali metal into an oxygen environment. For example, the compound thin film may be composed of Si/Cs/O. The work functions of the thin films can be varied by changing the silicon/alkali metal/oxygen ratio. Low work functions of the compound thin films deposited on silicon substrates were confirmed by ultraviolet photoelectron spectroscopy (UPS). The compound thin films are stable up to 500.degree. C. as measured by x-ray photoelectron spectroscopy (XPS). Tests have established that for certain chemical compositions and annealing temperatures of the compound thin films, negative electron affinity (NEA) was detected. The low work function, stable compound thin films can be utilized in solar cells, field emission flat panel displays, electron guns, and cold cathode electron guns.

  5. Thin film-coated polymer webs

    DOE Patents [OSTI]

    Wenz, Robert P. (Cottage Grove, MN); Weber, Michael F. (Shoreview, MN); Arudi, Ravindra L. (Woodbury, MN)

    1992-02-04

    The present invention relates to thin film-coated polymer webs, and more particularly to thin film electronic devices supported upon a polymer web, wherein the polymer web is treated with a purifying amount of electron beam radiation.

  6. Semiconductor-nanocrystal/conjugated polymer thin films

    DOE Patents [OSTI]

    Alivisatos, A. Paul (Oakland, CA); Dittmer, Janke J. (Munich, DE); Huynh, Wendy U. (Munich, DE); Milliron, Delia (Berkeley, CA)

    2010-08-17

    The invention described herein provides for thin films and methods of making comprising inorganic semiconductor-nanocrystals dispersed in semiconducting-polymers in high loading amounts. The invention also describes photovoltaic devices incorporating the thin films.

  7. Laser damage resistance of hafnia thin films deposited by electron beam deposition, reactive low voltage ion plating, and dual ion beam sputtering

    SciTech Connect (OSTI)

    Gallais, Laurent; Capoulade, Jeremie; Natoli, Jean-Yves; Commandre, Mireille; Cathelinaud, Michel; Koc, Cian; Lequime, Michel

    2008-05-01

    A comparative study is made of the laser damage resistance of hafnia coatings deposited on fused silica substrates with different technologies: electron beam deposition (from Hf or HfO2 starting material), reactive low voltage ion plating, and dual ion beam sputtering.The laser damage thresholds of these coatings are determined at 1064 and 355 nm using a nanosecond pulsed YAG laser and a one-on-one test procedure. The results are associated with a complete characterization of the samples: refractive index n measured by spectrophotometry, extinction coefficient k measured by photothermal deflection, and roughness measured by atomic force microscopy.

  8. Microstructural characterization of a thin film ZrN diffusion barrier in an As-fabricated U–7Mo/Al matrix dispersion fuel plate

    SciTech Connect (OSTI)

    Keiser, Dennis D.; Perez, Emmanuel; Wiencek, Tom; Leenaers, Ann; Van den Berghe, Sven

    2015-03-01

    The United States High Performance Research Reactor Fuel Development program is developing low enriched uranium fuels for application in research and test reactors. One concept utilizes U–7 wt.% Mo (U–7Mo) fuel particles dispersed in Al matrix, where the fuel particles are coated with a 1 ?m-thick ZrN coating. The ZrN serves as a diffusion barrier to eliminate a deleterious reaction that can occur between U–7Mo and Al when a dispersion fuel is irradiated under aggressive reactor conditions. To investigate the final microstructure of a physically-vapor-deposited ZrN coating in a dispersion fuel plate after it was fabricated using a rolling process, characterization samples were taken from a fuel plate that was fabricated at 500 °C using ZrN-coated U–7Mo particles, Al matrix and AA6061 cladding. Scanning electron and transmission electron microscopy analysis were performed. Data from these analyses will be used to support future microstructural examinations of irradiated fuel plates, in terms of understanding the effects of irradiation on the ZrN microstructure, and to determine the role of diffusion barrier microstructure in eliminating fuel/matrix interactions during irradiation. The as-fabricated coating was determined to be cubic-ZrN (cF8) phase. It exhibited a columnar microstructure comprised of nanometer-sized grains and a region of relatively high porosity, mainly near the Al matrix. Small impurity-containing phases were observed at the U–7Mo/ZrN interface, and no interaction zone was observed at the ZrN/Al interface. The bonding between the U–7Mo and ZrN appeared to be mechanical in nature. A relatively high level of oxygen was observed in the ZrN coating, extending from the Al matrix in the ZrN coating in decreasing concentration. The above microstructural characteristics are discussed in terms of what may be most optimal for a diffusion barrier in a dispersion fuel plate application.

  9. Modeling and control of thin film surface morphology: application to thin film solar cells

    E-Print Network [OSTI]

    Huang, Jianqiao

    2012-01-01

    Solar Energy Materials and Solar Cells, 86:207–216, 2005. [silicon thin films and solar cells. Journal of Appliedof a p-i-n thin-film solar cell with front transparent con-

  10. Polycrystalline Thin Film Solar Cell Technologies: Preprint

    SciTech Connect (OSTI)

    Ullal, H. S.

    2008-12-01

    Rapid progress is being made by CdTe and CIGS-based thin-film PV technologies in entering commercial markets.

  11. Thin film buried anode battery

    DOE Patents [OSTI]

    Lee, Se-Hee (Lakewood, CO); Tracy, C. Edwin (Golden, CO); Liu, Ping (Denver, CO)

    2009-12-15

    A reverse configuration, lithium thin film battery (300) having a buried lithium anode layer (305) and process for making the same. The present invention is formed from a precursor composite structure (200) made by depositing electrolyte layer (204) onto substrate (201), followed by sequential depositions of cathode layer (203) and current collector (202) on the electrolyte layer. The precursor is subjected to an activation step, wherein a buried lithium anode layer (305) is formed via electroplating a lithium anode layer at the interface of substrate (201) and electrolyte film (204). The electroplating is accomplished by applying a current between anode current collector (201) and cathode current collector (202).

  12. Thin Film Encapsulation Methods for Large Area MEMS Packaging

    E-Print Network [OSTI]

    Mahajerin, Armon

    2012-01-01

    P. J. French, “Robust Wafer-Level Thin-Film Encapsulation ofThe Elastic Properties of Thin- Film Silicon Nitride,” IEEELPCVD Silicon Nitride Thin Films at Cryogenic Temperatures,”

  13. Material Development for Highly Processable Thin Film Solar Cells

    E-Print Network [OSTI]

    Bob, Brion

    2014-01-01

    Structuring of Thin-film Solar Cells with a Single Laser1. Background on Thin Film Solar Cells and TransparentCuIn(Se,S)2 thin film solar cells: Secondary phases and

  14. Creating CZTS Thin Films Via Stacked Metallic CVD and Sulfurization

    E-Print Network [OSTI]

    Bielecki, Anthony

    2013-01-01

    Katagiri, Cu2ZnSnS4 thin film solar cells, Thin Solid FilmsIndium Galenide Films Thin-film solar cells are created bycandidate for thin- film solar cells. CIGS solar cell

  15. Molecular solution processing of metal chalcogenide thin film solar cells

    E-Print Network [OSTI]

    Yang, Wenbing

    2013-01-01

    to High-Efficiency CZTSSe Thin-film Solar Cells, Proc. IEEEMetal chalcogenide-based thin film solar cells are currentlyof metal chalcogenide thin film solar cells A dissertation

  16. Thin films of mixed metal compounds

    DOE Patents [OSTI]

    Mickelsen, Reid A. (Bellevue, WA); Chen, Wen S. (Seattle, WA)

    1985-01-01

    A compositionally uniform thin film of a mixed metal compound is formed by simultaneously evaporating a first metal compound and a second metal compound from independent sources. The mean free path between the vapor particles is reduced by a gas and the mixed vapors are deposited uniformly. The invention finds particular utility in forming thin film heterojunction solar cells.

  17. Atomistic surface erosion and thin film growth modelled over...

    Office of Scientific and Technical Information (OSTI)

    Atomistic surface erosion and thin film growth modelled over realistic time scales Citation Details In-Document Search Title: Atomistic surface erosion and thin film growth...

  18. Institute of Photo Electronic Thin Film Devices and Technology...

    Open Energy Info (EERE)

    Institute of Photo Electronic Thin Film Devices and Technology of Nankai University Jump to: navigation, search Name: Institute of Photo-Electronic Thin Film Devices and Technology...

  19. Solvothermal Thin Film Deposition of Electron Blocking Layers...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Solvothermal Thin Film Deposition of Electron Blocking Layers Home > Research > ANSER Research Highlights > Solvothermal Thin Film Deposition of Electron Blocking Layers...

  20. High Temperature Thin Film Polymer Dielectric Based Capacitors...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Temperature Thin Film Polymer Dielectric Based Capacitors for HEV Power Electronic Systems High Temperature Thin Film Polymer Dielectric Based Capacitors for HEV Power Electronic...

  1. A Sensitivity Analysis of a Thin Film Conductivity Estimation...

    Office of Scientific and Technical Information (OSTI)

    Conference: A Sensitivity Analysis of a Thin Film Conductivity Estimation Method Citation Details In-Document Search Title: A Sensitivity Analysis of a Thin Film Conductivity...

  2. Multilayer Thin-Film Thermoelectric Materials for Vehicle Applications...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Multilayer Thin-Film Thermoelectric Materials for Vehicle Applications Multilayer Thin-Film Thermoelectric Materials for Vehicle Applications 2004 Diesel Engine Emissions Reduction...

  3. Semiconductor-nanocrystal/conjugated polymer thin films (Patent...

    Office of Scientific and Technical Information (OSTI)

    Semiconductor-nanocrystalconjugated polymer thin films Citation Details In-Document Search Title: Semiconductor-nanocrystalconjugated polymer thin films You are accessing a...

  4. Zinc oxide thin film acoustic sensor

    SciTech Connect (OSTI)

    Mohammed, Ali Jasim; Salih, Wafaa Mahdi; Hassan, Marwa Abdul Muhsien; Nusseif, Asmaa Deiaa; Kadhum, Haider Abdullah [Department of Physics , College of Science, Al-Mustansiriyah University, Baghdad (Iraq); Mansour, Hazim Louis [Department of Physics , College of Education, Al-Mustansiriyah University, Baghdad (Iraq)

    2013-12-16

    This paper reports the implementation of (750 nm) thickness of Zinc Oxide (ZnO) thin film for the piezoelectric pressure sensors. The film was prepared and deposited employing the spray pyrolysis technique. XRD results show that the growth preferred orientation is the (002) plane. A polycrystalline thin film (close to mono crystallite like) was obtained. Depending on the Scanning Electron Microscopy photogram, the film homogeneity and thickness were shown. The resonance frequency measured (about 19 kHz) and the damping coefficient was calculated and its value was found to be about (2.5538), the thin film be haves as homogeneous for under and over damped. The thin film pressure sensing was approximately exponentially related with frequency, the thin film was observed to has a good response for mechanical stresses also it is a good material for the piezoelectric properties.

  5. Shielding superconductors with thin films

    E-Print Network [OSTI]

    Posen, Sam; Catelani, Gianluigi; Liepe, Matthias U; Sethna, James P

    2015-01-01

    Determining the optimal arrangement of superconducting layers to withstand large amplitude AC magnetic fields is important for certain applications such as superconducting radiofrequency cavities. In this paper, we evaluate the shielding potential of the superconducting film/insulating film/superconductor (SIS') structure, a configuration that could provide benefits in screening large AC magnetic fields. After establishing that for high frequency magnetic fields, flux penetration must be avoided, the superheating field of the structure is calculated in the London limit both numerically and, for thin films, analytically. For intermediate film thicknesses and realistic material parameters we also solve numerically the Ginzburg-Landau equations. It is shown that a small enhancement of the superheating field is possible, on the order of a few percent, for the SIS' structure relative to a bulk superconductor of the film material, if the materials and thicknesses are chosen appropriately.

  6. Structural characterization of thin film photonic crystals

    SciTech Connect (OSTI)

    Subramania, G.; Biswas, R.; Constant, K.; Sigalas, M. M.; Ho, K. M.

    2001-06-15

    We quantitatively analyze the structure of thin film inverse-opal photonic crystals composed of ordered arrays of air pores in a background of titania. Ordering of the sphere template and introduction of the titania background were performed simultaneously in the thin film photonic crystals. Nondestructive optical measurements of backfilling with high refractive index liquids, angle-resolved reflectivity, and optical spectroscopy were combined with band-structure calculations. The analysis reveals a thin film photonic crystal structure with a very high filling fraction (92{endash}94%) of air and a substantial compression along the c axis ({similar_to}22{endash}25%).

  7. Permanent laser conditioning of thin film optical materials

    DOE Patents [OSTI]

    Wolfe, C.R.; Kozlowski, M.R.; Campbell, J.H.; Staggs, M.; Rainer, F.

    1995-12-05

    The invention comprises a method for producing optical thin films with a high laser damage threshold and the resulting thin films. The laser damage threshold of the thin films is permanently increased by irradiating the thin films with a fluence below an unconditioned laser damage threshold. 9 figs.

  8. Permanent laser conditioning of thin film optical materials

    DOE Patents [OSTI]

    Wolfe, C. Robert (Palo Alto, CA); Kozlowski, Mark R. (Pleasanton, CA); Campbell, John H. (Livermore, CA); Staggs, Michael (Tracy, CA); Rainer, Frank (Livermore, CA)

    1995-01-01

    The invention comprises a method for producing optical thin films with a high laser damage threshold and the resulting thin films. The laser damage threshold of the thin films is permanently increased by irradiating the thin films with a fluence below an unconditioned laser damage threshold.

  9. Durham Workshop, Dec 2005Durham Workshop, Dec 2005 Thin Film Metrology UsingThin Film Metrology Using

    E-Print Network [OSTI]

    Greenaway, Alan

    Durham Workshop, Dec 2005Durham Workshop, Dec 2005 Thin Film Metrology UsingThin Film Metrology Modelling to investigate level of aberrations introduced by thin film structure.introduced by thin film Solar Cells Reflectors Solar Cell Covers Security UV Protection Anti-static Gas Temperature Pressure

  10. Nanomechanical properties of hydrated organic thin films

    E-Print Network [OSTI]

    Choi, Jae Hyeok

    2007-01-01

    Hydrated organic thin films are biological or synthetic molecularly thin coatings which impart a particular functionality to an underlying substrate and which have discrete water molecules associated with them. Such films ...

  11. Thin film production method and apparatus

    DOE Patents [OSTI]

    Loutfy, Raouf O. (Tucson, AZ); Moravsky, Alexander P. (Tucson, AZ); Hassen, Charles N. (Tucson, AZ)

    2010-08-10

    A method for forming a thin film material which comprises depositing solid particles from a flowing suspension or aerosol onto a filter and next adhering the solid particles to a second substrate using an adhesive.

  12. Polycrystalline Thin-Film Multijunction Solar Cells

    SciTech Connect (OSTI)

    Noufi, R.; Wu, X.; Abu-Shama, J.; Ramanathan, K; Dhere, R.; Zhou, J.; Coutts, T.; Contreras, M.; Gessert, T.; Ward, J. S.

    2005-11-01

    We present a digest of our research on the thin-film material components that comprise the top and bottom cells of three different material systems and the tandem devices constructed from them.

  13. A thin film transistor driven microchannel device 

    E-Print Network [OSTI]

    Lee, Hyun Ho

    2005-02-17

    THIN FILM TRANSISTOR DRIVEN MICROCHANNEL DEVICE FOR PROTEIN AND DNA ELECTROPHORESIS A Dissertation by HYUN HO LEE Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements... for the degree of DOCTOR OF PHILOSOPHY December 2004 Major Subject: Chemical Engineering A THIN FILM TRANSISTOR DRIVEN MICROCHANNEL DEVICE FOR PROTEIN AND DNA ELECTROPHORESIS A Dissertation by HYUN HO LEE Submitted to Texas A...

  14. Fully Solution-Processed Copper Chalcopyrite Thin Film Solar Cells: Materials Chemistry, Processing, and Device Physics

    E-Print Network [OSTI]

    Chung, Choong-Heui

    2012-01-01

    CuIn(Se,S) 2 thin film solar cells: secondary phaseChalcopyrite Thin Film Solar Cells: Materials Chemistry,Chalcopyrite Thin Film Solar Cells: Materials Chemistry,

  15. Ambient pressure process for preparing aerogel thin films reliquified sols useful in preparing aerogel thin films

    DOE Patents [OSTI]

    Brinker, Charles Jeffrey (Albuquerque, NM); Prakash, Sai Sivasankaran (Minneapolis, MN)

    1999-01-01

    A method for preparing aerogel thin films by an ambient-pressure, continuous process. The method of this invention obviates the use of an autoclave and is amenable to the formation of thin films by operations such as dip coating. The method is less energy intensive and less dangerous than conventional supercritical aerogel processing techniques.

  16. The interplay between spatially separated ferromagnetic and superconducting thin films 

    E-Print Network [OSTI]

    Sullivan, Isaac John

    2013-02-22

    characterized. 26 CHAPTER III THE SC/FM THIN FILM MULTILAYER The fabrication and characterization of the SC/FM film couples comprised the most de- manding and arduous work during the tenure of my thesis project. Many special parts were designed... EXPERIMENTAL DETAILS A. Ferromagnetic Thin Films 1. Film Preparation 2. Film Characterization B. Superconducting Thin Films 1. Film Preparation III THE SC/FM THIN FILM MULTILAYER . A. SC/FM Thin Film Multilayer Preparation B. SC/FM Thin Film Multilayer...

  17. Sputter deposition for multi-component thin films

    DOE Patents [OSTI]

    Krauss, A.R.; Auciello, O.

    1990-05-08

    Ion beam sputter-induced deposition using a single ion beam and a multicomponent target is capable of reproducibly producing thin films of arbitrary composition, including those which are close to stoichiometry. Using a quartz crystal deposition monitor and a computer controlled, well-focused ion beam, this sputter-deposition approach is capable of producing metal oxide superconductors and semiconductors of the superlattice type such as GaAs-AlGaAs as well as layered metal/oxide/semiconductor/superconductor structures. By programming the dwell time for each target according to the known sputtering yield and desired layer thickness for each material, it is possible to deposit composite films from a well-controlled sub-monolayer up to thicknesses determined only by the available deposition time. In one embodiment, an ion beam is sequentially directed via a set of X-Y electrostatic deflection plates onto three or more different element or compound targets which are constituents of the desired film. In another embodiment, the ion beam is directed through an aperture in the deposition plate and is displaced under computer control to provide a high degree of control over the deposited layer. In yet another embodiment, a single fixed ion beam is directed onto a plurality of sputter targets in a sequential manner where the targets are each moved in alignment with the beam under computer control in forming a multilayer thin film. This controlled sputter-deposition approach may also be used with laser and electron beams. 10 figs.

  18. Sputter deposition for multi-component thin films

    DOE Patents [OSTI]

    Krauss, Alan R. (Plainfield, IL); Auciello, Orlando (Cary, NC)

    1990-01-01

    Ion beam sputter-induced deposition using a single ion beam and a multicomponent target is capable of reproducibly producing thin films of arbitrary composition, including those which are close to stoichiometry. Using a quartz crystal deposition monitor and a computer controlled, well-focused ion beam, this sputter-deposition approach is capable of producing metal oxide superconductors and semiconductors of the superlattice type such as GaAs-AlGaAs as well as layered metal/oxide/semiconductor/superconductor structures. By programming the dwell time for each target according to the known sputtering yield and desired layer thickness for each material, it is possible to deposit composite films from a well-controlled sub-monolayer up to thicknesses determined only by the available deposition time. In one embodiment, an ion beam is sequentially directed via a set of X-Y electrostatic deflection plates onto three or more different element or compound targets which are constituents of the desired film. In another embodiment, the ion beam is directed through an aperture in the deposition plate and is displaced under computer control to provide a high degree of control over the deposited layer. In yet another embodiment, a single fixed ion beam is directed onto a plurality of sputter targets in a sequential manner where the targets are each moved in alignment with the beam under computer control in forming a multilayer thin film. This controlled sputter-deposition approach may also be used with laser and electron beams.

  19. Thin film absorber for a solar collector

    DOE Patents [OSTI]

    Wilhelm, William G. (Cutchogue, NY)

    1985-01-01

    This invention pertains to energy absorbers for solar collectors, and more particularly to high performance thin film absorbers. The solar collectors comprising the absorber of this invention overcome several problems seen in current systems, such as excessive hardware, high cost and unreliability. In the preferred form, the apparatus features a substantially rigid planar frame with a thin film window bonded to one planar side of the frame. An absorber in accordance with the present invention is comprised of two thin film layers that are sealed perimetrically. In a preferred embodiment, thin film layers are formed from a metal/plastic laminate. The layers define a fluid-tight planar envelope of large surface area to volume through which a heat transfer fluid flows. The absorber is bonded to the other planar side of the frame. The thin film construction of the absorber assures substantially full envelope wetting and thus good efficiency. The window and absorber films stress the frame adding to the overall strength of the collector.

  20. Thin film dielectric composite materials

    SciTech Connect (OSTI)

    Jia, Quanxi; Gibbons, Brady J.; Findikoglu, Alp T.; Park, Bae Ho

    2002-01-01

    A dielectric composite material comprising at least two crystal phases of different components with TiO.sub.2 as a first component and a material selected from the group consisting of Ba.sub.1-x Sr.sub.x TiO.sub.3 where x is from 0.3 to 0.7, Pb.sub.1-x Ca.sub.x TiO.sub.3 where x is from 0.4 to 0.7, Sr.sub.1-x Pb.sub.x TiO.sub.3 where x is from 0.2 to 0.4, Ba.sub.1-x Cd.sub.x TiO.sub.3 where x is from 0.02 to 0.1, BaTi.sub.1-x Zr.sub.x O.sub.3 where x is from 0.2 to 0.3, BaTi.sub.1-x Sn.sub.x O.sub.3 where x is from 0.15 to 0.3, BaTi.sub.1-x Hf.sub.x O.sub.3 where x is from 0.24 to 0.3, Pb.sub.1-1.3x La.sub.x TiO.sub.3+0.2x where x is from 0.23 to 0.3, (BaTiO.sub.3).sub.x (PbFeo.sub.0.5 Nb.sub.0.5 O.sub.3).sub.1-x where x is from 0.75 to 0.9, (PbTiO.sub.3).sub.- (PbCo.sub.0.5 W.sub.0.5 O.sub.3).sub.1-x where x is from 0.1 to 0.45, (PbTiO.sub.3).sub.x (PbMg.sub.0.5 W.sub.0.5 O.sub.3).sub.1-x where x is from 0.2 to 0.4, and (PbTiO.sub.3).sub.x (PbFe.sub.0.5 Ta.sub.0.5 O.sub.3).sub.1-x where x is from 0 to 0.2, as the second component is described. The dielectric composite material can be formed as a thin film upon suitable substrates.

  1. Tungsten-doped thin film materials

    DOE Patents [OSTI]

    Xiang, Xiao-Dong; Chang, Hauyee; Gao, Chen; Takeuchi, Ichiro; Schultz, Peter G.

    2003-12-09

    A dielectric thin film material for high frequency use, including use as a capacitor, and having a low dielectric loss factor is provided, the film comprising a composition of tungsten-doped barium strontium titanate of the general formula (Ba.sub.x Sr.sub.1-x)TiO.sub.3, where X is between about 0.5 and about 1.0. Also provided is a method for making a dielectric thin film of the general formula (Ba.sub.x Sr.sub.1-x)TiO.sub.3 and doped with W, where X is between about 0.5 and about 1.0, a substrate is provided, TiO.sub.2, the W dopant, Ba, and optionally Sr are deposited on the substrate, and the substrate containing TiO.sub.2, the W dopant, Ba, and optionally Sr is heated to form a low loss dielectric thin film.

  2. Mesoscale morphologies in polymer thin films.

    SciTech Connect (OSTI)

    Ramanathan, M.; Darling, S. B. (Center for Nanoscale Materials)

    2011-06-01

    In the midst of an exciting era of polymer nanoscience, where the development of materials and understanding of properties at the nanoscale remain a major R&D endeavor, there are several exciting phenomena that have been reported at the mesoscale (approximately an order of magnitude larger than the nanoscale). In this review article, we focus on mesoscale morphologies in polymer thin films from the viewpoint of origination of structure formation, structure development and the interaction forces that govern these morphologies. Mesoscale morphologies, including dendrites, holes, spherulites, fractals and honeycomb structures have been observed in thin films of homopolymer, copolymer, blends and composites. Following a largely phenomenological level of description, we review the kinetic and thermodynamic aspects of mesostructure formation outlining some of the key mechanisms at play. We also discuss various strategies to direct, limit, or inhibit the appearance of mesostructures in polymer thin films as well as an outlook toward potential areas of growth in this field of research.

  3. Thin Film Transistors On Plastic Substrates

    DOE Patents [OSTI]

    Carey, Paul G. (Mountain View, CA); Smith, Patrick M. (San Ramon, CA); Sigmon, Thomas W. (Portola Valley, CA); Aceves, Randy C. (Livermore, CA)

    2004-01-20

    A process for formation of thin film transistors (TFTs) on plastic substrates replaces standard thin film transistor fabrication techniques, and uses sufficiently lower processing temperatures so that inexpensive plastic substrates may be used in place of standard glass, quartz, and silicon wafer-based substrates. The silicon based thin film transistor produced by the process includes a low temperature substrate incapable of withstanding sustained processing temperatures greater than about 250.degree. C., an insulating layer on the substrate, a layer of silicon on the insulating layer having sections of doped silicon, undoped silicon, and poly-silicon, a gate dielectric layer on the layer of silicon, a layer of gate metal on the dielectric layer, a layer of oxide on sections of the layer of silicon and the layer of gate metal, and metal contacts on sections of the layer of silicon and layer of gate metal defining source, gate, and drain contacts, and interconnects.

  4. Vibration welding system with thin film sensor

    DOE Patents [OSTI]

    Cai, Wayne W; Abell, Jeffrey A; Li, Xiaochun; Choi, Hongseok; Zhao, Jingzhou

    2014-03-18

    A vibration welding system includes an anvil, a welding horn, a thin film sensor, and a process controller. The anvil and horn include working surfaces that contact a work piece during the welding process. The sensor measures a control value at the working surface. The measured control value is transmitted to the controller, which controls the system in part using the measured control value. The thin film sensor may include a plurality of thermopiles and thermocouples which collectively measure temperature and heat flux at the working surface. A method includes providing a welder device with a slot adjacent to a working surface of the welder device, inserting the thin film sensor into the slot, and using the sensor to measure a control value at the working surface. A process controller then controls the vibration welding system in part using the measured control value.

  5. Piezoreslstive graphite/polyimide thin films for micromachining applications

    E-Print Network [OSTI]

    Piezoreslstive graphite/polyimide thin films for micromachining applications A. Bruno Frazier) In this work, graphite/polyimide composite thin films are introduced and characterized for micromachining tetracarboxylic dianhydride+xydianiline/metaphenylene diamine polyimide matrix. The resultant material represents

  6. Creating CZTS Thin Films Via Stacked Metallic CVD and Sulfurization

    E-Print Network [OSTI]

    Bielecki, Anthony

    2013-01-01

    film solar cells. CIGS solar cell efficiencies have beenCIGS, making it a favorable choice for thin-film solar cells.thin film solar cell [3]. However, use of CIGS has a number

  7. Polymer-Metal Nanocomposites via Polymer Thin Film

    E-Print Network [OSTI]

    Shyamasundar, R.K.

    Polymer-Metal Nanocomposites via Polymer Thin Film T. P. Radhakrishnan School of Chemistry, University of Hyderabad Polymer-metal nanocomposite thin films are versatile materials that not only Chemistry Inside a Polymer Thin Film P. Radhakrishnan School of Chemistry, University of Hyderabad metal

  8. Environmental Aspects of Thin Film Module Production and Product Lifetime

    E-Print Network [OSTI]

    Bergman, Keren

    Impact #12;3 Thin-Film PV -The Triangle of SuccessThin-Film PV -The Triangle of Success Low Cost of Thin Film Module Production and Product Lifetime Vasilis Fthenakis PV Environmental Research Center@bnl.gov web: www.pv.bnl.gov www.clca.columbia.edu #12;2 PV Sustainability CriteriaPV Sustainability Criteria

  9. Modeling and control of thin film surface morphology: application to thin film solar cells

    E-Print Network [OSTI]

    Huang, Jianqiao

    2012-01-01

    Solar Energy Materials and Solar Cells, 86:207–216, 2005. [silicon thin films and solar cells. Journal of Appliedtrapping in nanostructured solar cells. ACS Nano, 5:10055–

  10. Modeling and control of thin film surface morphology: application to thin film solar cells

    E-Print Network [OSTI]

    Huang, Jianqiao

    2012-01-01

    modeling of ? -Si : H solar cells with rough interfaces:of a p-i-n thin-film solar cell with front transparent con-amorphous-silicon-based P-I-N solar cells deposited on rough

  11. Flexoelectricity in barium strontium titanate thin film

    SciTech Connect (OSTI)

    Kwon, Seol Ryung; Huang, Wenbin; Yuan, Fuh-Gwo; Jiang, Xiaoning, E-mail: xjiang5@ncsu.edu [Department of Mechanical and Aerospace Engineering, North Carolina State University, Raleigh, North Carolina 27695 (United States); Shu, Longlong [Department of Mechanical and Aerospace Engineering, North Carolina State University, Raleigh, North Carolina 27695 (United States); Electronic Materials Research Laboratory, International Center for Dielectric Research, Xi'an Jiao Tong University, Xi'an, Shaanxi 710049 (China); Maria, Jon-Paul [Department of Material Science and Engineering, North Carolina State University, Raleigh, North Carolina 27695 (United States)

    2014-10-06

    Flexoelectricity, the linear coupling between the strain gradient and the induced electric polarization, has been intensively studied as an alternative to piezoelectricity. Especially, it is of interest to develop flexoelectric devices on micro/nano scales due to the inherent scaling effect of flexoelectric effect. Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} thin film with a thickness of 130?nm was fabricated on a silicon wafer using a RF magnetron sputtering process. The flexoelectric coefficients of the prepared thin films were determined experimentally. It was revealed that the thin films possessed a transverse flexoelectric coefficient of 24.5??C/m at Curie temperature (?28?°C) and 17.44??C/m at 41?°C. The measured flexoelectric coefficients are comparable to that of bulk BST ceramics, which are reported to be 10–100??C/m. This result suggests that the flexoelectric thin film structures can be effectively used for micro/nano-sensing devices.

  12. ORIGINAL PAPER Nanocrystalline Diamond Thin Films Synthesis

    E-Print Network [OSTI]

    Qin, Qinghua

    -CVD, and Meng [13] prepared NCD thin film on cemented carbide using a high extended DC arc plasma process substrate using direct current plasma jet chemical vapor deposition. A special cooling system was designed of Physics, Australian National University, Canberra, ACT 0200, Australia 123 Plasma Chem Plasma Process

  13. Thin film hydrous metal oxide catalysts

    DOE Patents [OSTI]

    Dosch, Robert G. (Albuquerque, NM); Stephens, Howard P. (Albuquerque, NM)

    1995-01-01

    Thin film (<100 nm) hydrous metal oxide catalysts are prepared by 1) synthesis of a hydrous metal oxide, 2) deposition of the hydrous metal oxide upon an inert support surface, 3) ion exchange with catalytically active metals, and 4) activating the hydrous metal oxide catalysts.

  14. Magnetic/metallic thin films and nanostructures

    E-Print Network [OSTI]

    Lewis, Robert Michael

    examples. During the past decade applications of nano-scale magnetic devices to data storage have hadMagnetic/metallic thin films and nanostructures The College of William and MarY;'l Virginia http://www.as.wm.cdu/Faculty/Lukaszcw.html It is widely believed that revolutionary progress can be made as materials and devices are developed to operate

  15. Thin film flow over substrates with topography P.H. Gaskell, Y.-Y. Koh, P.K. Jimack*, M. Sellier, H.M. Thompson and M.C.T. Wilson

    E-Print Network [OSTI]

    Jimack, Peter

    117 Thin film flow over substrates with topography P.H. Gaskell, Y.-Y. Koh, P.K. Jimack*, M, as it encounters well-defined topography, S(X,Y). It builds on, extends and complements the recent experimental on the substrate. Figure 1: A sketch of a thin film flow down an inclined plate featuring a topography

  16. Thin film photovoltaic panel and method

    DOE Patents [OSTI]

    Ackerman, Bruce (El Paso, TX); Albright, Scot P. (El Paso, TX); Jordan, John F. (El Paso, TX)

    1991-06-11

    A thin film photovoltaic panel includes a backcap for protecting the active components of the photovoltaic cells from adverse environmental elements. A spacing between the backcap and a top electrode layer is preferably filled with a desiccant to further reduce water vapor contamination of the environment surrounding the photovoltaic cells. The contamination of the spacing between the backcap and the cells may be further reduced by passing a selected gas through the spacing subsequent to sealing the backcap to the base of the photovoltaic panels, and once purged this spacing may be filled with an inert gas. The techniques of the present invention are preferably applied to thin film photovoltaic panels each formed from a plurality of photovoltaic cells arranged on a vitreous substrate. The stability of photovoltaic conversion efficiency remains relatively high during the life of the photovoltaic panel, and the cost of manufacturing highly efficient panels with such improved stability is significantly reduced.

  17. Multiferroic oxide thin films and heterostructures

    SciTech Connect (OSTI)

    Lu, Chengliang E-mail: Tao.Wu@kaust.edu.sa; Hu, Weijin; Wu, Tom E-mail: Tao.Wu@kaust.edu.sa; Tian, Yufeng

    2015-06-15

    Multiferroic materials promise a tantalizing perspective of novel applications in next-generation electronic, memory, and energy harvesting technologies, and at the same time they also represent a grand scientific challenge on understanding complex solid state systems with strong correlations between multiple degrees of freedom. In this review, we highlight the opportunities and obstacles in growing multiferroic thin films with chemical and structural integrity and integrating them in functional devices. Besides the magnetoelectric effect, multiferroics exhibit excellent resistant switching and photovoltaic properties, and there are plenty opportunities for them to integrate with other ferromagnetic and superconducting materials. The challenges include, but not limited, defect-related leakage in thin films, weak magnetism, and poor control on interface coupling. Although our focuses are Bi-based perovskites and rare earth manganites, the insights are also applicable to other multiferroic materials. We will also review some examples of multiferroic applications in spintronics, memory, and photovoltaic devices.

  18. Electrostatic thin film chemical and biological sensor

    DOE Patents [OSTI]

    Prelas, Mark A. (Columbia, MO); Ghosh, Tushar K. (Columbia, MO); Tompson, Jr., Robert V. (Columbia, MO); Viswanath, Dabir (Columbia, MO); Loyalka, Sudarshan K. (Columbia, MO)

    2010-01-19

    A chemical and biological agent sensor includes an electrostatic thin film supported by a substrate. The film includes an electrostatic charged surface to attract predetermined biological and chemical agents of interest. A charge collector associated with said electrostatic thin film collects charge associated with surface defects in the electrostatic film induced by the predetermined biological and chemical agents of interest. A preferred sensing system includes a charge based deep level transient spectroscopy system to read out charges from the film and match responses to data sets regarding the agents of interest. A method for sensing biological and chemical agents includes providing a thin sensing film having a predetermined electrostatic charge. The film is exposed to an environment suspected of containing the biological and chemical agents. Quantum surface effects on the film are measured. Biological and/or chemical agents can be detected, identified and quantified based on the measured quantum surface effects.

  19. Preparation of thin film high temperature superconductors

    SciTech Connect (OSTI)

    VenKatesan, X.X.T.; Li, Q.; Findikoglu, A.; Hemmick, D. . Dept. of Physics); Wu, X.D. ); Inam, A.; Chang, C.C.; Ramesh, R.; Hwang, D.M.; Ravi, T.S.; Etemad, S.; Martinez, J.A.; Wilkens, B. )

    1991-03-01

    This paper addresses fundamental issues in preparing high quality high T{sub c} YBa{sub 2}Cu{sub 3}O{sub 7{minus}x} thin films. The techniques of inverted cylindrical magnetron sputtering and pulsed laser deposition are chosen as successful examples to illustrate how the key problems can be solved. The fabrication of YBa{sub 2}Cu{sub 3}O{sub 7{minus}x}/PrBa{sub 2}Cu{sub 3}O{sub 7{minus}x} superlattices where superconductivity in a single unit cell layer of YBa{sub 2}Cu{sub 3}O{sub 7{minus}x} was observed demonstrates the state of the art of thin film deposition of high T{sub c} materials. Systematic variations of the deposition parameters result in changes of superconducting and structural properties of the films that correlate with their microwave and infrared characteristics.

  20. Substrate heater for thin film deposition

    DOE Patents [OSTI]

    Foltyn, Steve R. (111 Beryl St., Los Alamos, NM 87544)

    1996-01-01

    A substrate heater for thin film deposition of metallic oxides upon a target substrate configured as a disk including means for supporting in a predetermined location a target substrate configured as a disk, means for rotating the target substrate within the support means, means for heating the target substrate within the support means, the heating means about the support means and including a pair of heating elements with one heater element situated on each side of the predetermined location for the target substrate, with one heater element defining an opening through which desired coating material can enter for thin film deposition and with the heating means including an opening slot through which the target substrate can be entered into the support means, and, optionally a means for thermal shielding of the heating means from surrounding environment is disclosed.

  1. Superconducting thin films on potassium tantalate substrates

    DOE Patents [OSTI]

    Feenstra, Roeland (Oak Ridge, TN); Boatner, Lynn A. (Oak Ridge, TN)

    1992-01-01

    A superconductive system for the lossless transmission of electrical current comprising a thin film of superconducting material Y.sub.1 Ba.sub.2 Cu.sub.3 O.sub.7-x epitaxially deposited upon a KTaO.sub.3 substrate. The KTaO.sub.3 is an improved substrate over those of the prior art since the it exhibits small lattice constant mismatch and does not chemically react with the superconducting film.

  2. Packaging material for thin film lithium batteries

    DOE Patents [OSTI]

    Bates, John B. (116 Baltimore Dr., Oak Ridge, TN 37830); Dudney, Nancy J. (11634 S. Monticello Rd., Knoxville, TN 37922); Weatherspoon, Kim A. (223 Wadsworth Pl., Oak Ridge, TN 37830)

    1996-01-01

    A thin film battery including components which are capable of reacting upon exposure to air and water vapor incorporates a packaging system which provides a barrier against the penetration of air and water vapor. The packaging system includes a protective sheath overlying and coating the battery components and can be comprised of an overlayer including metal, ceramic, a ceramic-metal combination, a parylene-metal combination, a parylene-ceramic combination or a parylene-metal-ceramic combination.

  3. Measuring the thermal boundary conductance between graphite and thin film by time-domain thermoreflectance

    E-Print Network [OSTI]

    Maruyama, Shigeo

    Variable Delay CCD Detector Aperture /2 plate Optical Isolator Electro-Optic Modulator Pump Beam Probe Beam in this study: (a) sectional view; and (b) TBC model. Probe HOPG Al thin film Pump z dHOPG dAlkAl kHOPG DAl()sinh( )sinh( 1 )cosh( f M f qdqdkq qd kq qd f (2) Volumetric heat capacity [106 Jm-3 K-1 ] Thermal

  4. Band Gap Energy of Chalcopyrite Thin Film Solar Cell Absorbers Determined by Soft X-Ray Emission and Absorption Spectroscopy

    E-Print Network [OSTI]

    Bar, M.

    2010-01-01

    OF CHALCOPYRITE THIN FILM SOLAR CELL ABSORBERS DETERMINED BYchalcopyrite thin film solar cell absorbers significantlyof chalcopyrite thin film solar cell absorbers. excitation

  5. Overview and Challenges of Thin Film Solar Electric Technologies

    SciTech Connect (OSTI)

    Ullal, H. S.

    2008-12-01

    In this paper, we report on the significant progress made worldwide by thin-film solar cells, namely, amorphous silicon (a-Si), cadmium telluride (CdTe), and copper indium gallium diselenide (CIGS). Thin-film photovoltaic (PV) technology status is also discussed in detail. In addition, R&D and technology challenges in all three areas are elucidated. The worldwide estimated projection for thin-film PV technology production capacity announcements are estimated at more than 5000 MW by 2010.

  6. Creating CZTS Thin Films Via Stacked Metallic CVD and Sulfurization

    E-Print Network [OSTI]

    Bielecki, Anthony

    2013-01-01

    Research, Thin-Film Photovoltaic (PV) Cells Market Analysiscost of photovoltaic systems (such as solar cells) due tosolar cells are created by depositing layers of photovoltaic

  7. Rechargeable thin film battery and method for making the same

    DOE Patents [OSTI]

    Goldner, Ronald B.; Liu, Te-Yang; Goldner, Mark A.; Gerouki, Alexandra; Haas, Terry E.

    2006-01-03

    A rechargeable, stackable, thin film, solid-state lithium electrochemical cell, thin film lithium battery and method for making the same is disclosed. The cell and battery provide for a variety configurations, voltage and current capacities. An innovative low temperature ion beam assisted deposition method for fabricating thin film, solid-state anodes, cathodes and electrolytes is disclosed wherein a source of energetic ions and evaporants combine to form thin film cell components having preferred crystallinity, structure and orientation. The disclosed batteries are particularly useful as power sources for portable electronic devices and electric vehicle applications where high energy density, high reversible charge capacity, high discharge current and long battery lifetimes are required.

  8. Tax Credits Give Thin-Film Solar a Big Boost

    Office of Energy Efficiency and Renewable Energy (EERE)

    California company will expand its capacity to make its thin-film solar panels by more than ten times, thanks to two Recovery Act tax credits.

  9. Fast lithium-ion conducting thin film electrolytes integrated...

    Office of Scientific and Technical Information (OSTI)

    Fast lithium-ion conducting thin film electrolytes integrated directly on flexible substrates for high power solid-state batteries. Citation Details In-Document Search Title: Fast...

  10. Production and characterization of thin film group IIIB, IVB...

    Office of Scientific and Technical Information (OSTI)

    Production and characterization of thin film group IIIB, IVB and rare earth hydrides by reactive evaporation Citation Details In-Document Search Title: Production and...

  11. Orientational Analysis of Molecules in Thin Films | Stanford...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    crucial if an epitaxial or even crystalline organic growth is desired, if such thin film should serve as template or anchoring unit for further depositiongrowth in a...

  12. Molecular solution processing of metal chalcogenide thin film solar cells

    E-Print Network [OSTI]

    Yang, Wenbing

    2013-01-01

    for further improvement on CZTS solar cells efficiency.improvement. Figure 6.1 Efficiency progress for hydrazine solution processing CIGS and CZTS thin film solar cells

  13. Graphene as tunable contact for high performance thin film transistor

    E-Print Network [OSTI]

    Liu, Yuan

    2015-01-01

    64 Figure 4-5. Air stability of a planar PCBM thin filmfilm. . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . .obtained by annealing 8-nm thick gold thin film. . . . .

  14. Uncooled thin film pyroelectric IR detector with aerogel thermal isolation

    DOE Patents [OSTI]

    Ruffner, Judith A. (Albuquerque, NM); Bullington, Jeff A. (Albuquerque, NM); Clem, Paul G. (Albuquerque, NM); Warren, William L. (Albuquerque, NM); Brinker, C. Jeffrey (Albuquerque, NM); Tuttle, Bruce A. (Albuquerque, NM); Schwartz, Robert W. (Seneca, SC)

    1999-01-01

    A monolithic infrared detector structure which allows integration of pyroelectric thin films atop low thermal conductivity aerogel thin films. The structure comprises, from bottom to top, a substrate, an aerogel insulating layer, a lower electrode, a pyroelectric layer, and an upper electrode layer capped by a blacking layer. The aerogel can offer thermal conductivity less than that of air, while providing a much stronger monolithic alternative to cantilevered or suspended air-gap structures for pyroelectric thin film pixel arrays. Pb(Zr.sub.0.4 Ti.sub.0.6)O.sub.3 thin films deposited on these structures displayed viable pyroelectric properties, while processed at 550.degree. C.

  15. Fabrication of Microporous Thin Films from Polyelectrolyte Multilayers

    E-Print Network [OSTI]

    Barrett, Christopher

    , are established biomaterials finding application as drug delivery systems, enteric coatings for drugs, dental and biomaterial applications. Introduction The fabrication of polyelectrolyte multilayer thin films has received

  16. Thermoelectric effect in very thin film Pt/Au thermocouples

    E-Print Network [OSTI]

    Salvadori, M.C.; Vaz, A.R.; Teixeira, F.S.; Cattani, M.; Brown, I.G.

    2006-01-01

    TABLE I. Measured thermoelectric power S for samples ofThermoelectric effect in very thin film Pt/Au thermocouplesthickness dependence of the thermoelectric power of Pt films

  17. Development of a cell culture surface conversion technique using alginate thin film for evaluating effect upon cellular differentiation

    SciTech Connect (OSTI)

    Nakashima, Y.; Tsusu, K.; Minami, K.; Nakanishi, Y.

    2014-06-15

    Here, we sought to develop a cell culture surface conversion technique that would not damage living cells. An alginate thin film, formed on a glass plate by spin coating of sodium alginate solution and dipping into calcium chloride solution, was used to inhibit adhesion of cells. The film could be removed by ethylenediaminetetraacetate (EDTA) at any time during cell culture, permitting observation of cellular responses to conversion of the culture surface in real time. Additionally, we demonstrated the validity of the alginate thin film coating method and the performance of the film. The thickness of the alginate thin film was controlled by varying the rotation speed during spin coating. Moreover, the alginate thin film completely inhibited the adhesion of cultured cells to the culture surface, irrespective of the thickness of the film. When the alginate thin film was removed from the culture surface by EDTA, the cultured cells adhered to the culture surface, and their morphology changed. Finally, we achieved effective differentiation of C2C12 myoblasts into myotube cells by cell culture on the convertible culture surface, demonstrating the utility of our novel technique.

  18. Innovative Thin Films LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIXsource History View NewGuam:on Openei |sourceAndInformation ReeseInnovativeThin Films

  19. Tuning the Magnetic and Electronic Properties of FexSi1-x Thin Films for Spintronics

    E-Print Network [OSTI]

    Karel, Julie Elizabeth

    2012-01-01

    x Si 1-x Thin Films for Spintronics By Julie Elizabeth Karelx Si 1-x Thin Films for Spintronics Copyright 2012 by Juliex Si 1-x Thin Films for Spintronics by Julie Elizabeth Karel

  20. Quantification of thin film crystallographic orientation using X-ray diffraction with an area detector

    E-Print Network [OSTI]

    Baker, Jessica L

    2010-01-01

    properties of Au thin films by X?ray diffraction and in in  polythiophene thin?film transistors.  Nat Mater 2006, copper  phthalocyanine thin films evaporated on amorphous 

  1. The Effects of Non-Uniform Electronic Properties on Thin Film Photovoltaics

    E-Print Network [OSTI]

    Brown, Gregory Ferguson

    2011-01-01

    Intensity  in  Thin  Film  Solar  Cells   3.2.1   U.  Rau,  EL)  Intensity   in  Thin  Film  Solar  Cells   3.3  properties  of  thin  film  solar  cell   absorbers,  with  

  2. Accounting for Localized Defects in the Optoelectronic Design of Thin-Film Solar Cells

    E-Print Network [OSTI]

    Deceglie, Michael G.

    2014-01-01

    trapping in silicon thin film solar cells," Solar Energy,textured surfaces in thin-film solar cells," Opt. Express,Design of Plasmonic Thin-Film Solar Cells with Broadband

  3. Thin-film chip-to-substrate interconnect and methods for making same

    DOE Patents [OSTI]

    Tuckerman, David B. (Livermore, CA)

    1991-01-01

    Integrated circuit chips are electrically connected to a silica wafer interconnection substrate. Thin film wiring is fabricated down bevelled edges of the chips. A subtractive wire fabrication method uses a series of masks and etching steps to form wires in a metal layer. An additive method direct laser writes or deposits very thin metal lines which can then be plated up to form wires. A quasi-additive or subtractive/additive method forms a pattern of trenches to expose a metal surface which can nucleate subsequent electrolytic deposition of wires. Low inductance interconnections on a 25 micron pitch (1600 wires on a 1 cm square chip) can be produced. The thin film hybrid interconnect eliminates solder joints or welds, and minimizes the levels of metallization. Advantages include good electrical properties, very high wiring density, excellent backside contact, compactness, and high thermal and mechanical reliability.

  4. Rechargeable thin-film lithium batteries

    SciTech Connect (OSTI)

    Bates, J.B.; Gruzalski, G.R.; Dudney, N.J.; Luck, C.F.; Yu, X.

    1993-09-01

    Rechargeable thin-film batteries consisting of lithium metal anodes, an amorphous inorganic electrolyte, and cathodes of lithium intercalation compounds have been fabricated and characterized. These include Li-TiS{sub 2}, Li-V{sub 2}O{sub 5}, and Li-Li{sub x}Mn{sub 2}O{sub 4} cells with open circuit voltages at full charge of about 2.5 V, 3.7 V, and 4.2 V, respectively. The realization of these robust cells, which can be cycled thousands of times, was possible because of the stability of the amorphous lithium electrolyte, lithium phosphorus oxynitride. This material has a typical composition of Li{sub 2.9}PO{sub 3.3}N{sub 0.46}and a conductivity at 25 C of 2 {mu}S/cm. The thin-film cells have been cycled at 100% depth of discharge using current densities of 5 to 100 {mu}A/cm{sup 2}. Over most of the charge-discharge range, the internal resistance appears to be dominated by the cathode, and the major source of the resistance is the diffusion of Li{sup +} ions from the electrolyte into the cathode. Chemical diffusion coefficients were determined from ac impedance measurements.

  5. VACUUM PUMPING STUDY OF TITANIUM-ZIRCONIUM-VANADIUM THIN FILMS*

    E-Print Network [OSTI]

    ERL 03-8 VACUUM PUMPING STUDY OF TITANIUM-ZIRCONIUM-VANADIUM THIN FILMS* Yulin Li# and Simon Ho, LEPP, Cornell University, Ithaca, NY 14853, USA Abstract* Vacuum pumping via non-evaporable getter (NEG) thin film deposited directly onto the interior of a vacuum chamber is a novel way to achieve extreme

  6. Multilayer thin-film coatings for optical communication systems

    E-Print Network [OSTI]

    Miller, David A. B.

    Multilayer thin-film coatings for optical communication systems Martina Gerken Lichttechnisches-film coatings for optical communication systems are reviewed. Particular emphasis is given to thin-film designs with dispersion related to the photonic crystal superprism effect. A single dispersive coating may be used

  7. A survey of thin-film solar photovoltaic industry & technologies

    E-Print Network [OSTI]

    Grama, Sorin

    2007-01-01

    A new type of solar cell technology using so-called thin-film solar photovoltaic material has the potential to make a great impact on our lives. Because it uses very little or no silicon at all, thin- film (TF) solar ...

  8. Photochemical Pattern Transfer and Enhancement of Thin Film Silica

    E-Print Network [OSTI]

    Parikh, Atul N.

    Photochemical Pattern Transfer and Enhancement of Thin Film Silica Mesophases Andrew M. Dattelbaum chemical treatment of the film can selectively remove the mesostructured regions, leading to patterned, hydrophobicity, and structural morphology of the mesoscopic thin film material on a wide range of substrates

  9. Fracture patterns in thin films and multilayers Alex A. Volinsky

    E-Print Network [OSTI]

    Volinsky, Alex A.

    Fracture patterns in thin films and multilayers Alex A. Volinsky University of South Florida, excessive residual and externally applied stresses cause film fracture. In the case of tensile stress is the key for causing thin film fracture, either in tension, or compression, it is the influence

  10. Accounting for Localized Defects in the Optoelectronic Design of Thin-Film Solar Cells

    E-Print Network [OSTI]

    Deceglie, Michael G.

    2014-01-01

    in ultrathin plasmonic solar cells," Optics Express, vol.Bailat, "Thin-film silicon solar cell technology," Progresstrapping in silicon thin film solar cells," Solar Energy,

  11. The Electrodeless Discharge Lamps Coated with the Titania Thin Film for Photocatalysis in a Microwave Field

    E-Print Network [OSTI]

    Cirkva, Vladimir

    The Electrodeless Discharge Lamps Coated with the Titania Thin Film for Photocatalysis assisted photocatalysis using TiO2 thin films has been examined. Several factors influencing

  12. Stress Evolution Behavior in CoCrPt Alloy Thin Films with varying Pt Concentration

    E-Print Network [OSTI]

    Im, M.-Y.

    2009-01-01

    Stress Evolution Behavior in CoCrPt Alloy Thin Films withmagnetic recording media is to investigate growth stress,since stress inevitably generated during thin film

  13. TEM characterization of nanodiamond thin films.

    SciTech Connect (OSTI)

    Qin, L.-C.; Zhou, D.; Krauss, A. R.; Gruen, D. M.; Chemistry

    1998-05-01

    The microstructure of thin films grown by microwave plasma-enhanced chemical vapor deposition (MPCVD) from fullerene C{sub 60} precursors has been characterized by scanning electron microscopy (SEM), selected-area electron diffraction (SAED), bright-field electron microscopy, high-resolution electron microscopy (HREM), and parallel electron energy loss spectroscopy (PEELS). The films are composed of nanosize crystallites of diamond, and no graphitic or amorphous phases were observed. The diamond crystallite size measured from lattice images shows that most grains range between 3-5 nm, reflecting a gamma distribution. SAED gave no evidence of either sp2-bonded glassy carbon or sp3-bonded diamondlike amorphous carbon. The sp2-bonded configuration found in PEELS was attributed to grain boundary carbon atoms, which constitute 5-10% of the total. Occasionally observed larger diamond grains tend to be highly faulted.

  14. Thin Film Femtosecond Laser Damage Competition

    SciTech Connect (OSTI)

    Stolz, C J; Ristau, D; Turowski, M; Blaschke, H

    2009-11-14

    In order to determine the current status of thin film laser resistance within the private, academic, and government sectors, a damage competition was started at the 2008 Boulder Damage Symposium. This damage competition allows a direct comparison of the current state of the art of high laser resistance coatings since they are tested using the same damage test setup and the same protocol. In 2009 a high reflector coating was selected at a wavelength of 786 nm at normal incidence at a pulse length of 180 femtoseconds. A double blind test assured sample and submitter anonymity so only a summary of the results are presented here. In addition to the laser resistance results, details of deposition processes, coating materials and layer count, and spectral results will also be shared.

  15. Glow discharge plasma deposition of thin films

    DOE Patents [OSTI]

    Weakliem, Herbert A. (Pennington, NJ); Vossen, Jr., John L. (Bridgewater, NJ)

    1984-05-29

    A glow discharge plasma reactor for deposition of thin films from a reactive RF glow discharge is provided with a screen positioned between the walls of the chamber and the cathode to confine the glow discharge region to within the region defined by the screen and the cathode. A substrate for receiving deposition material from a reactive gas is positioned outside the screened region. The screen is electrically connected to the system ground to thereby serve as the anode of the system. The energy of the reactive gas species is reduced as they diffuse through the screen to the substrate. Reactive gas is conducted directly into the glow discharge region through a centrally positioned distribution head to reduce contamination effects otherwise caused by secondary reaction products and impurities deposited on the reactor walls.

  16. Thin films of mixed metal compounds

    DOE Patents [OSTI]

    Mickelsen, R.A.; Chen, W.S.

    1985-06-11

    Disclosed is a thin film heterojunction solar cell, said heterojunction comprising a p-type I-III-IV[sub 2] chalcopyrite substrate and an overlying layer of an n-type ternary mixed metal compound wherein said ternary mixed metal compound is applied to said substrate by introducing the vapor of a first metal compound to a vessel containing said substrate from a first vapor source while simultaneously introducing a vapor of a second metal compound from a second vapor source of said vessel, said first and second metals comprising the metal components of said mixed metal compound; independently controlling the vaporization rate of said first and second vapor sources; reducing the mean free path between vapor particles in said vessel, said gas being present in an amount sufficient to induce homogeneity of said vapor mixture; and depositing said mixed metal compound on said substrate in the form of a uniform composition polycrystalline mixed metal compound. 5 figs.

  17. Rechargeable thin-film electrochemical generator

    DOE Patents [OSTI]

    Rouillard, Roger (Beloeil, CA); Domroese, Michael K. (South St. Paul, MN); Hoffman, Joseph A. (Minneapolis, MN); Lindeman, David D. (Hudson, WI); Noel, Joseph-Robert-Gaetan (St-Hubert, CA); Radewald, Vern E. (Austin, TX); Ranger, Michel (Lachine, CA); Sudano, Anthony (Laval, CA); Trice, Jennifer L. (Eagan, MN); Turgeon, Thomas A. (Fridley, MN)

    2000-09-15

    An improved electrochemical generator is disclosed. The electrochemical generator includes a thin-film electrochemical cell which is maintained in a state of compression through use of an internal or an external pressure apparatus. A thermal conductor, which is connected to at least one of the positive or negative contacts of the cell, conducts current into and out of the cell and also conducts thermal energy between the cell and thermally conductive, electrically resistive material disposed on a vessel wall adjacent the conductor. The thermally conductive, electrically resistive material may include an anodized coating or a thin sheet of a plastic, mineral-based material or conductive polymer material. The thermal conductor is fabricated to include a resilient portion which expands and contracts to maintain mechanical contact between the cell and the thermally conductive material in the presence of relative movement between the cell and the wall structure. The electrochemical generator may be disposed in a hermetically sealed housing.

  18. The state of the art of thin-film photovoltaics

    SciTech Connect (OSTI)

    Surek, T.

    1993-10-01

    Thin-film photovoltaic technologies, based on materials such as amorphous or polycrystalline silicon, copper indium diselenide, cadmium telluride, and gallium arsenide, offer the potential for significantly reducing the cost of electricity generated by photovoltaics. The significant progress in the technologies, from the laboratory to the marketplace, is reviewed. The common concerns and questions raised about thin films are addressed. Based on the progress to date and the potential of these technologies, along with continuing investments by the private sector to commercialize the technologies, one can conclude that thin-film PV will provide a competitive alternative for large-scale power generation in the future.

  19. STRESS-INDUCED PERIODIC FRACTURE PATTERNS IN THIN FILMS Alex A. Volinsky1

    E-Print Network [OSTI]

    Volinsky, Alex A.

    STRESS-INDUCED PERIODIC FRACTURE PATTERNS IN THIN FILMS Alex A. Volinsky1 , Neville R. Moody2 applied stresses in thin films can cause film fracture. In the case of compressive stress thin film stress a network of through- thickness cracks forms in thin films. Excessive biaxial residual stress

  20. Multimonth controlled small molecule release from biodegradable thin films

    E-Print Network [OSTI]

    Hammond, Paula T.

    Long-term, localized delivery of small molecules from a biodegradable thin film is challenging owing to their low molecular weight and poor charge density. Accomplishing highly extended controlled release can facilitate ...

  1. Molecular solution processing of metal chalcogenide thin film solar cells

    E-Print Network [OSTI]

    Yang, Wenbing

    2013-01-01

    S. Guha, High-Efficiency Cu2ZnSnSe4 Solar Cells with a TiNfurther improvement on CZTS solar cells efficiency. Finally,Route to High-Efficiency CZTSSe Thin-film Solar Cells, Proc.

  2. Enabling integration of vapor-deposited polymer thin films

    E-Print Network [OSTI]

    Petruczok, Christy D. (Christy Danielle)

    2014-01-01

    Initiated Chemical Vapor Deposition (iCVD) is a versatile, one-step process for synthesizing conformal and functional polymer thin films on a variety of substrates. This thesis emphasizes the development of tools to further ...

  3. MICROSTRUCTURE AND MECHANICAL PROPERTIES OF ELECTROPLATED Cu THIN FILMS

    E-Print Network [OSTI]

    Volinsky, Alex A.

    MICROSTRUCTURE AND MECHANICAL PROPERTIES OF ELECTROPLATED Cu THIN FILMS A.A. Volinsky* , J. Vella microns were electroplated on top of the adhesion-promoting barrier layers on single crystal silicon

  4. The macroscopic delamination of thin films from elastic substrates

    E-Print Network [OSTI]

    Reis, Pedro Miguel

    The wrinkling and delamination of stiff thin films adhered to a polymer substrate have important applications in “flexible electronics.” The resulting periodic structures, when used for circuitry, have remarkable mechanical ...

  5. Guided Self-Assembly of Gold Thin Films

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Guided Self-Assembly of Gold Thin Films Print Nanoparticles-man-made atoms with unique optical, electrical, and mechanical properties-have become key components in many fields of...

  6. Fluorination of amorphous thin-film materials with xenon fluoride

    DOE Patents [OSTI]

    Weil, R.B.

    1987-05-01

    A method is disclosed for producing fluorine-containing amorphous semiconductor material, preferably comprising amorphous silicon. The method includes depositing amorphous thin-film material onto a substrate while introducing xenon fluoride during the film deposition process.

  7. Initiated chemical vapor deposition of functional polyacrylic thin films

    E-Print Network [OSTI]

    Mao, Yu, 1975-

    2005-01-01

    Initiated chemical vapor deposition (iCVD) was explored as a novel method for synthesis of functional polyacrylic thin films. The process introduces a peroxide initiator, which can be decomposed at low temperatures (<200?C) ...

  8. Method for making surfactant-templated thin films

    DOE Patents [OSTI]

    Brinker, C. Jeffrey (Albuquerque, NM); Lu, Yunfeng (New Orleans, LA); Fan, Hong You (Albuquerque, NM)

    2010-08-31

    An evaporation-induced self-assembly method to prepare a porous, surfactant-templated, thin film by mixing a silica sol, a solvent, a surfactant, and an interstitial compound, evaporating a portion of the solvent to form a liquid, crystalline thin film mesophase material, and then removal of the surfactant template. Coating onto a substrate produces a thin film with the interstitial compound either covalently bonded to the internal surfaces of the ordered or disordered mesostructure framework or physically entrapped within the ordered or disordered mesostructured framework. Particles can be formed by aerosol processing or spray drying rather than coating onto a substrate. The selection of the interstitial compound provides a means for developing thin films for applications including membranes, sensors, low dielectric constant films, photonic materials and optical hosts.

  9. Chemical vapor deposition of organosilicon and sacrificial polymer thin films

    E-Print Network [OSTI]

    Casserly, Thomas Bryan

    2005-01-01

    Chemical vapor deposition (CVD) produced films for a wide array of applications from a variety of organosilicon and organic precursors. The structure and properties of thin films were controlled by varying processing ...

  10. Direct printing of lead zirconate titanate thin films

    E-Print Network [OSTI]

    Bathurst, Stephen, 1980-

    2008-01-01

    Thus far, use of lead zirconate titanate (PZT) in MEMS has been limited due to the lack of process compatibility with existing MEMS manufacturing techniques. Direct printing of thin films eliminates the need for photolithographic ...

  11. Functionalized multilayer thin films for protection against acutely toxic agents

    E-Print Network [OSTI]

    Krogman, Kevin Christopher

    2009-01-01

    The recently developed practice of spraying polyelectrolyte solutions onto a substrate in order to construct thin films via the Layer-by-Layer (LbL) technique has been further investigated and extended. In this process a ...

  12. Optical and Structural Characterizations of Tin Phthalocvanine Thin Films

    SciTech Connect (OSTI)

    Cherian, Regimol C.; Menon, C. S. [School of Pure and Applied Physics, Mahatma Gandhi University Priyadarshini Hills P.O., Kottayam-686560, Kerala (India)

    2008-04-23

    Phthalocyanines are today regarded as optical materials, which applies to organic dye lasers. The analysis of the optical properties of these thin films enforces the application in the field of thin film optics. Tin phthalocyanine (SnPc) thin films used for the characterization studies are prepared by thermal evaporation technique. The variation of optical band gap with irradiation of heat radiation and post deposition heat treatment are studied from the absorption spectra. Structural properties have been analyzed using the X-ray diffractogram of SnPc powder and thin films. The structure is identified as monoclinic with a = 12.132 A, b = 8.712 A, c = 10.806 A and {beta} = 108.85 deg. The grain size increases with increase of annealing temperature. The SEM images show a rough corrugated surface. Due to heat treatment, crystallites grow into bigger size.

  13. Efficient light trapping structure in thin film silicon solar cells

    E-Print Network [OSTI]

    Sheng, Xing

    Thin film silicon solar cells are believed to be promising candidates for continuing cost reduction in photovoltaic panels because silicon usage could be greatly reduced. Since silicon is an indirect bandgap semiconductor, ...

  14. Properties and sensor performance of zinc oxide thin films

    E-Print Network [OSTI]

    Min, Yongki, 1965-

    2003-01-01

    Reactively sputtered ZnO thin film gas sensors were fabricated onto Si wafers. The atmosphere dependent electrical response of the ZnO micro arrays was examined. The effects of processing conditions on the properties and ...

  15. TiNi-based thin films for MEMS applications

    E-Print Network [OSTI]

    Fu, Yongqing

    In this paper, some critical issues and problems in the development of TiNi thin films were discussed, including preparation and characterization considerations, residual stress and adhesion, frequency improvement, fatigue ...

  16. Functionality Tuning in Vertically Aligned Nanocomposite Thin Films 

    E-Print Network [OSTI]

    Chen, Aiping

    2013-04-04

    Vertically aligned nanocomposite (VAN) oxide thin films are unique nanostructures with two-phase self-assembled, heteroepitaxially grown on single-crystal substrates. Both phases tend to grow vertically and simultaneously ...

  17. Nanostructured thin films for solid oxide fuel cells 

    E-Print Network [OSTI]

    Yoon, Jongsik

    2009-05-15

    The goals of this work were to synthesize high performance perovskite based thin film solid oxide fuel cell (TF-SOFC) cathodes by pulsed laser deposition (PLD), to study the structural, electrical and electrochemical properties of these cathodes...

  18. Antimony-Doped Tin(II) Sulfide Thin Films

    E-Print Network [OSTI]

    Chakraborty, Rupak

    Thin-film solar cells made from earth-abundant, inexpensive, and nontoxic materials are needed to replace the current technologies whose widespread use is limited by their use of scarce, costly, and toxic elements. Tin ...

  19. June 26, 2000 1 Fracture in Thin Films

    E-Print Network [OSTI]

    Suo, Zhigang

    in many technologies. Examples include zirconia coatings as thermal barriers on superalloys in enginesJune 26, 2000 1 Fracture in Thin Films Z. Suo Mechanical and Aerospace Engineering Department

  20. Self-Assembling Process for Fabricating Tailored Thin Films

    ScienceCinema (OSTI)

    None

    2010-01-08

    A simple, economical nanotechnology coating process that enables the development of nanoparticle thin films with architectures and properties unattainable by any other processing method. 2007 R&D 100 winner (SAND2007-1878P)

  1. Self-Assembling Process for Fabricating Tailored Thin Films

    ScienceCinema (OSTI)

    Sandia

    2009-09-01

    A simple, economical nanotechnology coating process that enables the development of nanoparticle thin films with architectures and properties unattainable by any other processing method. 2007 R&D 100 winner (SAND2007-1878P)

  2. Modeling of thin-film solar thermoelectric generators

    E-Print Network [OSTI]

    Weinstein, Lee Adragon

    Recent advances in solar thermoelectric generator (STEG) performance have raised their prospect as a potential technology to convert solar energy into electricity. This paper presents an analysis of thin-film STEGs. ...

  3. Sol-gel-derived Epitaxial Nanocomposite Thin Films with Large...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Sol-gel-derived Epitaxial Nanocomposite Thin Films with Large Sharp Magnetoelectric Effect Home Author: B. Liu, T. Sun, J. He, V. P. Dravid Year: 2010 Abstract: Nanostructures of...

  4. Simple flash evaporator for making thin films of compounds

    SciTech Connect (OSTI)

    Hemanadhan, M.; Bapanayya, Ch.; Agarwal, S. C. [Department of Physics, Indian Institute of Technology, Kanpur 208016 (India)

    2010-07-15

    A simple and compact arrangement for flash evaporation is described. It uses a cell phone vibrator for powder dispensing that can be incorporated into a vacuum deposition chamber without any major alterations. The performance of the flash evaporation system is checked by making thin films of the optical memory chalcogenide glass Ge{sub 2}Sb{sub 2}Te{sub 5} (GST). Energy dispersive x-ray analysis shows that the flash evaporation preserves the stoichiometry in thin films.

  5. Oxynitride Thin Film Barriers for PV Packaging

    SciTech Connect (OSTI)

    Glick, S. H.; delCueto, J. A.; Terwilliger, K. M.; Jorgensen, G. J.; Pankow, J. W.; Keyes, B. M.; Gedvilas, L. M.; Pern, F. J.

    2005-11-01

    Dielectric thin-film barrier and adhesion-promoting layers consisting of silicon oxynitride materials (SiOxNy, with various stoichiometry) were investigated. For process development, films were applied to glass (TCO, conductive SnO2:F; or soda-lime), polymer (PET, polyethylene terephthalate), aluminized soda-lime glass, or PV cell (a-Si, CIGS) substrates. Design strategy employed de-minimus hazard criteria to facilitate industrial adoption and reduce implementation costs for PV manufacturers or suppliers. A restricted process window was explored using dilute compressed gases (3% silane, 14% nitrous oxide, 23% oxygen) in nitrogen (or former mixtures, and 11.45% oxygen mix in helium and/or 99.999% helium dilution) with a worst-case flammable and non-corrosive hazard classification. Method employed low radio frequency (RF) power, less than or equal to 3 milliwatts per cm2, and low substrate temperatures, less than or equal to 100 deg C, over deposition areas less than or equal to 1000 cm2. Select material properties for barrier film thickness (profilometer), composition (XPS/FTIR), optical (refractive index, %T and %R), mechanical peel strength and WVTR barrier performance are presented.

  6. Transparent conducting thin films for spacecraft applications

    SciTech Connect (OSTI)

    Perez-Davis, M.E.; Malave-Sanabria, T.; Hambourger, P.; Rutledge, S.K.; Roig, D.; Degroh, K.K.; Hung, C.

    1994-01-01

    Transparent conductive thin films are required for a variety of optoelectronic applications: automotive and aircraft windows, and solar cells for space applications. Transparent conductive coatings of indium-tin-oxide (ITO)-magnesium fluoride (MgF2) and aluminum doped zinc oxide (AZO) at several dopant levels are investigated for electrical resistivity (sheet resistance), carrier concentration, optical properties, and atomic oxygen durability. The sheet resistance values of ITO-MgF2 range from 10[sup 2] to 10[sup 11] ohms/square, with transmittance of 75 to 86 percent. The AZO films sheet resistances range from 10[sup 7] to 10[sup 11] ohms/square with transmittances from 84 to 91 percent. It was found that in general, with respect to the optical properties, the zinc oxide (ZnO), AZO, and the high MgF2 content ITO-MgF2 samples, were all durable to atomic oxygen plasma, while the low MgF2 content of ITO-MgF2 samples were not durable to atomic oxygen plasma exposure.

  7. Thin film deposition by electric and magnetic crossed-field diode sputtering

    DOE Patents [OSTI]

    Welch, Kimo M. (Mountain View, CA)

    1980-01-01

    Applying a thin film coating to the surface of a workpiece, in particular, applying a coating of titanium nitride to a klystron window by means of a crossed-field diode sputtering array. The array is comprised of a cohesive group of numerous small hollow electrically conducting cylinders and is mounted so that the open ends of the cylinders on one side of the group are adjacent a titanium cathode plate. The workpiece is mounted so as to face the open ends of the other side of the group. A magnetic field is applied to the array so as to be coaxial with the cylinders and a potential is applied across the cylinders and the cathode plate, the cylinders as an anode being positive with respect to the cathode plate. The cylinders, the cathode plate and the workpiece are situated in an atmosphere of nitrogen which becomes ionized such as by field emission because of the electric field between the cylinders and cathode plate, thereby establishing an anode-cathode discharge that results in sputtering of the titanium plate. The sputtered titanium coats the workpiece and chemically combines with the nitrogen to form a titanium nitride coating on the workpiece. Gas pressure, gas mixtures, cathode material composition, voltages applied to the cathode and anode, the magnetic field, cathode, anode and workpiece spacing, and the aspect ratio (ratio of length to inner diameter) of the anode cylinders, all may be controlled to provide consistent optimum thin film coatings of various compositions and thicknesses. Another facet of the disclosure is the coating of microwave components per se with titanium nitride to reduce multipactoring under operating conditions of the components.

  8. Structure and properties of nanocrystalline ZrN{sub x}O{sub y} thin films: Effect of the oxygen content and film thickness

    SciTech Connect (OSTI)

    Lan, Kuan-Che; Hunag, Jia-Hong; Ai, Chi-Fong; Yu, Ge-Ping [Department of Engineering and System Science, National Tsing Hua University, 101 Kuang Fu Rd., Sec. 2, Hsinchu, 300 Taiwan (China); Institute of Nuclear Energy Research, Atomic Energy Council, Taoyuan, 325 Taiwan (China); Department of Engineering and System Science, National Tsing Hua University, 101 Kuang Fu Rd., Sec. 2, Hsinchu, 300 Taiwan (China) and Institute of Nuclear Engineering and Science, 101 Kuang Fu Rd., Sec. 2, Hsinchu, 300 Taiwan (China)

    2011-05-15

    The main objective of this study was to investigate the structure and properties of ZrN{sub x}O{sub y} thin films associated with oxygen content and film thickness. ZrN{sub x}O{sub y} thin films were deposited using hollow cathode discharge ion plating on Si (100) substrate. The thickness of ZrN{sub x}O{sub y} films increased with increasing oxygen flow rate, ranging from 143 to 894 nm. Phase separation from ZrN{sub x}O{sub y} to ZrN and monoclinic ZrO{sub 2} (m-ZrO{sub 2}) was observed by x-ray diffraction (XRD). The electrical and mechanical properties were influenced by the film thickness and the amount of separated phase, m-ZrO{sub 2}. ZrN{sub x}O{sub y} thin films with smaller thickness or deposited at higher O{sub 2} flow rate were found to have higher electrical resistivity. Hardness of the ZrN{sub x}O{sub y} thin films increased with increasing thickness, which could be related to microstructure change of the thin films. Residual stress of the ZrN phase in the ZrN{sub x}O{sub y} thin films, measured using the modified sin{sup 2} {psi} XRD method, decreased with increasing oxygen flow rate. The thickness dependence of the residual stress in ZrN was different with different oxygen flow rates. The average residual stress of the ZrN{sub x}O{sub y} thin films also decreased with increasing oxygen flow rate and the stress did not showed significant dependence on the film thickness.

  9. Nitrogen doped zinc oxide thin film

    SciTech Connect (OSTI)

    Li, Sonny X.

    2003-12-15

    To summarize, polycrystalline ZnO thin films were grown by reactive sputtering. Nitrogen was introduced into the films by reactive sputtering in an NO{sub 2} plasma or by N{sup +} implantation. All ZnO films grown show n-type conductivity. In unintentionally doped ZnO films, the n-type conductivities are attributed to Zn{sub i}, a native shallow donor. In NO{sub 2}-grown ZnO films, the n-type conductivity is attributed to (N{sub 2}){sub O}, a shallow double donor. In NO{sub 2}-grown ZnO films, 0.3 atomic % nitrogen was found to exist in the form of N{sub 2}O and N{sub 2}. Upon annealing, N{sub 2}O decomposes into N{sub 2} and O{sub 2}. In furnace-annealed samples N{sub 2} redistributes diffusively and forms gaseous N{sub 2} bubbles in the films. Unintentionally doped ZnO films were grown at different oxygen partial pressures. Zni was found to form even at oxygen-rich condition and led to n-type conductivity. N{sup +} implantation into unintentionally doped ZnO film deteriorates the crystallinity and optical properties and leads to higher electron concentration. The free electrons in the implanted films are attributed to the defects introduced by implantation and formation of (N{sub 2}){sub O} and Zni. Although today there is still no reliable means to produce good quality, stable p-type ZnO material, ZnO remains an attractive material with potential for high performance short wavelength optoelectronic devices. One may argue that gallium nitride was in a similar situation a decade ago. Although we did not obtain any p-type conductivity, we hope our research will provide a valuable reference to the literature.

  10. Chapter 1. Introduction to Thin Film Technologygy Thin films are deposited onto bulk materials (substrates) to achieveThin films are deposited onto bulk materials (substrates) to achieve

    E-Print Network [OSTI]

    Wang, Jianfang

    parts TiN coatings on cutting tools Offer hardness, low friction, and a chemical barrier to alloying on this system. #12;Thin films for multiple properties Cr coatings on automobile parts TiN coatings on cutting tools Impart hardness, metallic luster, and protection against ultraviolet light. Cr coatings on plastic

  11. Thin Film Packaging Solutions for High Efficiency OLED Lighting Products

    SciTech Connect (OSTI)

    None

    2008-06-30

    The objective of the 'Thin Film Packaging Solutions for High Efficiency OLED Lighting Products' project is to demonstrate thin film packaging solutions based on SiC hermetic coatings that, when applied to glass and plastic substrates, support OLED lighting devices by providing longer life with greater efficiency at lower cost than is currently available. Phase I Objective: Demonstrate thin film encapsulated working phosphorescent OLED devices on optical glass with lifetime of 1,000 hour life, CRI greater than 75, and 15 lm/W. Phase II Objective: Demonstrate thin film encapsulated working phosphorescent OLED devices on plastic or glass composite with 25 lm/W, 5,000 hours life, and CRI greater than 80. Phase III Objective: Demonstrate 2 x 2 ft{sup 2} thin film encapsulated working phosphorescent OLED with 40 lm/W, 10,000 hour life, and CRI greater than 85. This report details the efforts of Phase III (Budget Period Three), a fourteen month collaborative effort that focused on optimization of high-efficiency phosphorescent OLED devices and thin-film encapsulation of said devices. The report further details the conclusions and recommendations of the project team that have foundation in all three budget periods for the program. During the conduct of the Thin Film Packaging Solutions for High Efficiency OLED Lighting Products program, including budget period three, the project team completed and delivered the following achievements: (1) a three-year marketing effort that characterized the near-term and longer-term OLED market, identified customer and consumer lighting needs, and suggested prototype product concepts and niche OLED applications lighting that will give rise to broader market acceptance as a source for wide area illumination and energy conservation; (2) a thin film encapsulation technology with a lifetime of nearly 15,000 hours, tested by calcium coupons, while stored at 16 C and 40% relative humidity ('RH'). This encapsulation technology was characterized as having less than 10% change in transmission during the 15,000 hour test period; (3) demonstrated thin film encapsulation of a phosphorescent OLED device with 1,500 hours of lifetime at 60 C and 80% RH; (4) demonstrated that a thin film laminate encapsulation, in addition to the direct thin film deposition process, of a polymer OLED device was another feasible packaging strategy for OLED lighting. The thin film laminate strategy was developed to mitigate defects, demonstrate roll-to-roll process capability for high volume throughput (reduce costs) and to support a potential commercial pathway that is less dependent upon integrated manufacturing since the laminate could be sold as a rolled good; (5) demonstrated that low cost 'blue' glass substrates could be coated with a siloxane barrier layer for planarization and ion-protection and used in the fabrication of a polymer OLED lighting device. This study further demonstrated that the substrate cost has potential for huge cost reductions from the white borosilicate glass substrate currently used by the OLED lighting industry; (6) delivered four-square feet of white phosphorescent OLED technology, including novel high efficiency devices with 82 CRI, greater than 50 lm/W efficiency, and more than 1,000 hours lifetime in a product concept model shelf; (7) presented and or published more than twenty internal studies (for private use), three external presentations (OLED workshop-for public use), and five technology-related external presentations (industry conferences-for public use); and (8) issued five patent applications, which are in various maturity stages at time of publication. Delivery of thin film encapsulated white phosphorescent OLED lighting technology remains a challenging technical achievement, and it seems that commercial availability of thin, bright, white OLED light that meets market requirements will continue to require research and development effort. However, there will be glass encapsulated white OLED lighting products commercialized in niche markets during the 2008 calendar year. This commercializ

  12. Thin-film absorber for a solar collector

    SciTech Connect (OSTI)

    Wilhelm, W.G.

    1982-02-09

    This invention pertains to energy absorbers for solar collectors, and more particularly to high performance thin film absorbers. The solar collectors comprising the absorber of this invention overcome several problems seen in current systems, such as excessive hardware, high cost and unreliability. In the preferred form, the apparatus features a substantially rigid planar frame with a thin film window bonded to one planar side of the frame. An absorber in accordance with the present invention is comprised of two thin film layers that are sealed perimetrically. In a preferred embodiment, thin film layers are formed from a metal/plastic laminate. The layers define a fluid-tight planar envelope of large surface area to volume through which a heat transfer fluid flows. The absorber is bonded to the other planar side of the frame. The thin film construction of the absorber assures substantially full envelope wetting and thus good efficiency. The window and absorber films stress the frame adding to the overall strength of the collector.

  13. Uncooled thin film pyroelectric IR detector with aerogel thermal isolation

    SciTech Connect (OSTI)

    Ruffner, J.A.; Clem, P.G.; Tuttle, B.A. [and others

    1998-01-01

    Uncooled pyroelectric IR imaging systems, such as night vision goggles, offer important strategic advantages in battlefield scenarios and reconnaissance surveys. Until now, the current technology for fabricating these devices has been limited by low throughput and high cost which ultimately limit the availability of these sensor devices. We have developed and fabricated an alternative design for pyroelectric IR imaging sensors that utilizes a multilayered thin film deposition scheme to create a monolithic thin film imaging element on an active silicon substrate for the first time. This approach combines a thin film pyroelectric imaging element with a thermally insulating SiO{sub 2} aerogel thin film to produce a new type of uncooled IR sensor that offers significantly higher thermal, spatial, and temporal resolutions at a substantially lower cost per unit. This report describes the deposition, characterization and optimization of the aerogel thermal isolation layer and an appropriate pyroelectric imaging element. It also describes the overall integration of these components along with the appropriate planarization, etch stop, adhesion, electrode, and blacking agent thin film layers into a monolithic structure. 19 refs., 8 figs., 6 tabs.

  14. Low Temperature Chemical Vapor Deposition Of Thin Film Magnets

    DOE Patents [OSTI]

    Miller, Joel S. (Salt Lake City, UT); Pokhodnya, Kostyantyn I. (Salt Lake City, UT)

    2003-12-09

    A thin-film magnet formed from a gas-phase reaction of tetracyanoetheylene (TCNE) OR (TCNQ), 7,7,8,8-tetracyano-P-quinodimethane, and a vanadium-containing compound such as vanadium hexcarbonyl (V(CO).sub.6) and bis(benzene)vanalium (V(C.sub.6 H.sub.6).sub.2) and a process of forming a magnetic thin film upon at least one substrate by chemical vapor deposition (CVD) at a process temperature not exceeding approximately 90.degree. C. and in the absence of a solvent. The magnetic thin film is particularly suitable for being disposed upon rigid or flexible substrates at temperatures in the range of 40.degree. C. and 70.degree. C. The present invention exhibits air-stable characteristics and qualities and is particularly suitable for providing being disposed upon a wide variety of substrates.

  15. Shape variation of micelles in polymer thin films

    SciTech Connect (OSTI)

    Zhou, Jiajia Shi, An-Chang

    2014-01-14

    The equilibrium properties of block copolymer micelles confined in polymer thin films are investigated using self-consistent field theory. The theory is based on a model system consisting of AB diblock copolymers and A homopolymers. Two different methods, based on the radius of gyration tensor and the spherical harmonics expansion, are used to characterize the micellar shape. The results reveal that the morphology of micelles in thin films depends on the thickness of the thin films and the selectivity of the confining surfaces. For spherical (cylindrical) micelles, the spherical (cylindrical) symmetry is broken by the presence of the one-dimensional confinement, whereas the top-down symmetry is broken by the selectivity of the confining surfaces. Morphological transitions from spherical or cylindrical micelles to cylinders or lamella are predicted when the film thickness approaches the micellar size.

  16. Properties of zirconia thin films deposited by laser ablation

    SciTech Connect (OSTI)

    Cancea, V. N.; Filipescu, M.; Colceag, D.; Dinescu, M.; Mustaciosu, C.

    2013-11-13

    Zirconia thin films have been deposited by laser ablation of a ceramic ZrO{sub 2} target in vacuum or in oxygen background at 0.01 mbar. The laser beam generated by an ArF laser (?=193 nm, ?=40 Hz) has been focalized on the target through a spherical lens at an incident angle of 45°. The laser fluence has been established to a value from 2.0 to 3.4 Jcm{sup ?2}. A silicon (100) substrate has been placed parallel to the target, at a distance of 4 cm, and subsequently has been heated to temperatures ranging between 300 °C and 600 °C. Thin films morphology has been characterized by atomic force microscopy and secondary ion mass spectrometry. Biocompatibility of these thin films has been assessed by studying the cell attachment of L929 mouse fibroblasts.

  17. Fabrication of polycrystalline thin films by pulsed laser processing

    DOE Patents [OSTI]

    Mitlitsky, Fred (Livermore, CA); Truher, Joel B. (San Rafael, CA); Kaschmitter, James L. (Pleasanton, CA); Colella, Nicholas J. (Livermore, CA)

    1998-02-03

    A method for fabricating polycrystalline thin films on low-temperature (or high-temperature) substrates which uses processing temperatures that are low enough to avoid damage to the substrate, and then transiently heating select layers of the thin films with at least one pulse of a laser or other homogenized beam source. The pulse length is selected so that the layers of interest are transiently heated to a temperature which allows recrystallization and/or dopant activation while maintaining the substrate at a temperature which is sufficiently low to avoid damage to the substrate. This method is particularly applicable in the fabrication of solar cells.

  18. Fabrication of polycrystalline thin films by pulsed laser processing

    DOE Patents [OSTI]

    Mitlitsky, F.; Truher, J.B.; Kaschmitter, J.L.; Colella, N.J.

    1998-02-03

    A method is disclosed for fabricating polycrystalline thin films on low-temperature (or high-temperature) substrates which uses processing temperatures that are low enough to avoid damage to the substrate, and then transiently heating select layers of the thin films with at least one pulse of a laser or other homogenized beam source. The pulse length is selected so that the layers of interest are transiently heated to a temperature which allows recrystallization and/or dopant activation while maintaining the substrate at a temperature which is sufficiently low to avoid damage to the substrate. This method is particularly applicable in the fabrication of solar cells. 1 fig.

  19. Method of improving field emission characteristics of diamond thin films

    DOE Patents [OSTI]

    Krauss, Alan R. (Naperville, IL); Gruen, Dieter M. (Downer Grove, IL)

    1999-01-01

    A method of preparing diamond thin films with improved field emission properties. The method includes preparing a diamond thin film on a substrate, such as Mo, W, Si and Ni. An atmosphere of hydrogen (molecular or atomic) can be provided above the already deposited film to form absorbed hydrogen to reduce the work function and enhance field emission properties of the diamond film. In addition, hydrogen can be absorbed on intergranular surfaces to enhance electrical conductivity of the diamond film. The treated diamond film can be part of a microtip array in a flat panel display.

  20. Effect of current injection into thin-film Josephson junctions

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Kogan, V. G.; Mints, R. G.

    2014-11-11

    New thin-film Josephson junctions have recently been tested in which the current injected into one of the junction banks governs Josephson phenomena. One thus can continuously manage the phase distribution at the junction by changing the injected current. Our method of calculating the distribution of injected currents is also proposed for a half-infinite thin-film strip with source-sink points at arbitrary positions at the film edges. The strip width W is assumed small relative to ?=2?2/d;? is the bulk London penetration depth of the film material and d is the film thickness.

  1. Large area quantitative analysis of nanostructured thin-films

    E-Print Network [OSTI]

    Sliz, Rafal; Eneh, Chibuzor; Suzuki, Yuji; Czajkowski, Jakub; Fabritius, Tapio; Kathirgamanathan, Poopathy; Nathan, Arokia; Myllyla, Risto; Jabbour, Ghassan

    2015-01-09

    of SEM images of quantum dots and InP nanostructured thin-films are provided in the supple- mentary information. 3 Results 3.1 Physical Characterization The AFM and XRD techniques were used to verify the sur- face morphology and provide the reference... research subject for their high applicability in optoelectronics22–24. In addi- tion, self-assembled gold quantum dots and InP-based nanos- tructures were examined. Prior to the analysis, ZnO fabricated thin-films were additionally characterized with AFM...

  2. Method of improving field emission characteristics of diamond thin films

    DOE Patents [OSTI]

    Krauss, A.R.; Gruen, D.M.

    1999-05-11

    A method of preparing diamond thin films with improved field emission properties is disclosed. The method includes preparing a diamond thin film on a substrate, such as Mo, W, Si and Ni. An atmosphere of hydrogen (molecular or atomic) can be provided above the already deposited film to form absorbed hydrogen to reduce the work function and enhance field emission properties of the diamond film. In addition, hydrogen can be absorbed on intergranular surfaces to enhance electrical conductivity of the diamond film. The treated diamond film can be part of a microtip array in a flat panel display. 3 figs.

  3. Mode Splitting for Efficient Plasmoinc Thin-film Solar Cell

    E-Print Network [OSTI]

    Li, Tong; Jiang, Chun

    2010-01-01

    We propose an efficient plasmonic structure consisting of metal strips and thin-film silicon for solar energy absorption. We numerically demonstrate the absorption enhancement in symmetrical structure based on the mode coupling between the localized plasmonic mode in Ag strip pair and the excited waveguide mode in silicon slab. Then we explore the method of symmetry-breaking to excite the dark modes that can further enhance the absorption ability. We compare our structure with bare thin-film Si solar cell, and results show that the integrated quantum efficiency is improved by nearly 90% in such thin geometry. It is a promising way for the solar cell.

  4. Transparent and conductive indium doped cadmium oxide thin films prepared by pulsed filtered cathodic arc deposition

    E-Print Network [OSTI]

    Zhu, Yuankun

    2014-01-01

    7. Optical bandgap of the doped CdO thin films as a functionelectrical properties of In-doped CdO thin films fabricatedand transparent Ti-doped CdO films by pulsed laser

  5. Generation of low work function, stable compound thin films by laser ablation

    DOE Patents [OSTI]

    Dinh, Long N. (Concord, CA); McLean, II, William (Oakland, CA); Balooch, Mehdi (Berkeley, CA); Fehring, Jr., Edward J. (Dublin, CA); Schildbach, Marcus A. (Livermore, CA)

    2001-01-01

    Generation of low work function, stable compound thin films by laser ablation. Compound thin films with low work function can be synthesized by simultaneously laser ablating silicon, for example, and thermal evaporating an alkali metal into an oxygen environment. For example, the compound thin film may be composed of Si/Cs/O. The work functions of the thin films can be varied by changing the silicon/alkali metal/oxygen ratio. Low work functions of the compound thin films deposited on silicon substrates were confirmed by ultraviolet photoelectron spectroscopy (UPS). The compound thin films are stable up to 500.degree. C. as measured by x-ray photoelectron spectroscopy (XPS). Tests have established that for certain chemical compositions and annealing temperatures of the compound thin films, negative electron affinity (NEA) was detected. The low work function, stable compound thin films can be utilized in solar cells, field emission flat panel displays, electron guns, and cold cathode electron guns.

  6. The development of a thin-film rollforming process for pharmaceutical continuous manufacturing

    E-Print Network [OSTI]

    Slaughter, Ryan (Ryan R.)

    2013-01-01

    In this thesis, a continuous rollforming process for the folding of thin-films was proposed and studied as a key step in the continuous manufacturing of pharmaceutical tablets. HPMC and PEG based polymeric thin-films were ...

  7. Accounting for Localized Defects in the Optoelectronic Design of Thin-Film Solar Cells

    E-Print Network [OSTI]

    Deceglie, Michael G.

    2014-01-01

    W. Prather, "Thin film solar cell design based on photonicH. A. Atwater, "Design of nanostructured solar cells usingBrongersma, "Design of Plasmonic Thin-Film Solar Cells with

  8. PID Failure of c-Si and Thin-Film Modules and Possible Correlation...

    Energy Savers [EERE]

    PID Failure of c-Si and Thin-Film Modules and Possible Correlation with Leakage Currents PID Failure of c-Si and Thin-Film Modules and Possible Correlation with Leakage Currents...

  9. Electron-beam-evaporated thin films of hafnium dioxide for fabricating...

    Office of Scientific and Technical Information (OSTI)

    complementary metal-oxide semiconductor (CMOS) integrated circuits using this HfO2 thin film as the gate oxide. The authors analyzed the thin films using high-resolution...

  10. Cathodic ALD V2O5 thin films for high-rate electrochemical energy...

    Office of Scientific and Technical Information (OSTI)

    Cathodic ALD V2O5 thin films for high-rate electrochemical energy storage Citation Details In-Document Search Title: Cathodic ALD V2O5 thin films for high-rate electrochemical...

  11. Layer-by-Layer Assembly of Clay-filled Polymer Nanocomposite Thin Films 

    E-Print Network [OSTI]

    Jang, Woo-Sik

    2010-01-14

    robotic dipping system, for the preparation of these thin films, was built. The robot alternately dips a substrate into aqueous mixtures with rinsing and drying in between. Thin films of sodium montmorillonite clay and cationic polymer were grown...

  12. Characterization of Zirconium Phosphate/Polycation Thin Films Grown by Sequential Adsorption Reactions

    E-Print Network [OSTI]

    Characterization of Zirconium Phosphate/Polycation Thin Films Grown by Sequential Adsorption Received April 7, 1997X Monolayer and multilayer thin films consisting of anionic R-zirconium phosphate (R

  13. Engineering Al-based Thin Film Materials for Power Devices and Energy Storage Applications

    E-Print Network [OSTI]

    Perng, Ya-Chuan

    2012-01-01

    O Thin Films as a Solid Electrolyte for 3D Microbatteries,”Li 0.5 La 0.5 )TiO 3 solid electrolyte thin films grown byIonic conductivity in solid electrolytes based on lithium

  14. High efficiency thin film silicon solar cells with novel light trapping : principle, design and processing

    E-Print Network [OSTI]

    Zeng, Lirong, Ph. D. Massachusetts Institute of Technology

    2008-01-01

    One major efficiency limiting factor in thin film solar cells is weak absorption of long wavelength photons due to the limited optical path length imposed by the thin film thickness. This is especially severe in Si because ...

  15. Junction Evolution During Fabrication of CdS/CdTe Thin-film PV Solar Cells (Presentation)

    SciTech Connect (OSTI)

    Gessert, T. A.

    2010-09-01

    Discussion of the formation of CdTe thin-film PV junctions and optimization of CdTe thin-film PV solar cells.

  16. Dissolution dynamics of thin films measured by optical reflectance Christian Punckt and Ilhan A. Aksaya

    E-Print Network [OSTI]

    Aksay, Ilhan A.

    of copper thin films on gold substrates in a mild hydrochloric acid solution. Due to its simplicity, our of corrosion rates of thin films are in high demand for the quan- tification of material degradation measurement of dissolution rates of galvanically corrod- ing copper thin films based on bright field optical

  17. Performance predictions for monolithic, thin-film CdTe/Ge tandem solar cells

    E-Print Network [OSTI]

    Pulfrey, David L.

    Performance predictions for monolithic, thin-film CdTe/Ge tandem solar cells D.L. Pulfrey*, J. Dell): pulfrey@ece.ubc.ca ABSTRACT Cadmium telluride thin-film solar cells are now commercially available be attainable. 1. INTRODUCTION Thin film solar cells based on polycrystalline CdTe have been investigated

  18. EARTH ABUNDANT MATERIALS FOR HIGH EFFICIENCY HETEROJUNCTION THIN FILM SOLAR CELLS

    E-Print Network [OSTI]

    Ceder, Gerbrand

    materials for thin film solar cells such as CdTe and CIGS suffer from concerns over resource scarcity (eEARTH ABUNDANT MATERIALS FOR HIGH EFFICIENCY HETEROJUNCTION THIN FILM SOLAR CELLS Yun Seog Lee 1 conversion efficiencies should be increased. In terms of reducing module cost, thin film solar cells

  19. DETERMINING OPTICAL CONSTANTS OF URANIUM NITRIDE THIN FILMS IN THE EXTREME

    E-Print Network [OSTI]

    Hart, Gus

    deposition and characterization of reactively-sputtered uranium nitride thin films. I also report opticalDETERMINING OPTICAL CONSTANTS OF URANIUM NITRIDE THIN FILMS IN THE EXTREME ULTRAVIOLET (1.6-35 NM.1 Application 1 1.2 Optical Constants 2 1.3 Project Focus 7 2 Uranium Nitride Thin Films 8 2.1 Sputtering 8 2

  20. Small-scale thin film experiments provide models for large-scale engineering applications

    E-Print Network [OSTI]

    Reis, Pedro Miguel

    Small-scale thin film experiments provide models for large-scale engineering applicationsMIT's Department of Civil and Environmental Engineering · http://cee.mit.edu Delamination occurs in a thin film blisters occur in a predictable manner. Photo / Donna Coveney, MIT PROBLEM Thin films are omnipresent

  1. Physics of thin-film ferroelectric oxides DPMC, University of Geneva, CH-1211, Geneva 4, Switzerland

    E-Print Network [OSTI]

    Wu, Zhigang

    Physics of thin-film ferroelectric oxides M. Dawber* DPMC, University of Geneva, CH-1211, Geneva 4 of thin-film ferroelectric oxides, the strongest emphasis being on those aspects particular to ferroelectrics in thin-film form. The authors introduce the current state of development in the application

  2. Barium ferrite thin film media with perpendicular c-axis orientation and small grain size

    E-Print Network [OSTI]

    Laughlin, David E.

    Barium ferrite thin film media with perpendicular c-axis orientation and small grain size Zailong, Carnegie Mellon University, Pittsburgh, Pennsylvania 15213 Barium ferrite thin films with perpendicular c conditions. The c-axis orientation of barium ferrite thin films is most sensitive to the oxygen partial

  3. DISSERTATION ELECTRON-REFLECTOR STRATEGY FOR CdTe THIN-FILM SOLAR CELLS

    E-Print Network [OSTI]

    Sites, James R.

    DISSERTATION ELECTRON-REFLECTOR STRATEGY FOR CdTe THIN-FILM SOLAR CELLS Submitted by Kuo-Jui Hsiao ELECTRON- REFLECTOR STRATEGY FOR CdTe THIN-FILM SOLAR CELLS BE ACCEPTED AS FULFILLING IN PART REQUIREMENTS-FILM SOLAR CELLS The CdTe thin-film solar cell has a large absorption coefficient and high theoretical

  4. Femtosecond laser ablation of indium tin-oxide narrow grooves for thin film solar cells

    E-Print Network [OSTI]

    Van Stryland, Eric

    Femtosecond laser ablation of indium tin-oxide narrow grooves for thin film solar cells Qiumei Bian in the fabrication and assembly of thin film solar cells. Using a femtosecond (fs) laser, we selectively removed a unique scheme to ablate the indium tin-oxide layer for the fabrication of thin film solar cells

  5. Microwave plasma assisted supersonic gas jet deposition of thin film materials

    DOE Patents [OSTI]

    Schmitt, III, Jerome J. (New Haven, CT); Halpern, Bret L. (Bethany, CT)

    1993-01-01

    An apparatus for fabricating thin film materials utilizing high speed gas dynamics relies on supersonic free jets of carrier gas to transport depositing vapor species generated in a microwave discharge to the surface of a prepared substrate where the vapor deposits to form a thin film. The present invention generates high rates of deposition and thin films of unforeseen high quality at low temperatures.

  6. Metal-black scattering centers to enhance light harvesting by thin-film solar cells

    E-Print Network [OSTI]

    Peale, Robert E.

    Metal-black scattering centers to enhance light harvesting by thin-film solar cells Deep Panjwania as scattering centers to increase the effective optical thickness of thin-film solar cells. The particular type. Gold-black was deposited on commercial thin-film solar cells using a thermal evaporator in nitrogen

  7. Predictive Modeling for Glass-Side Laser Scribing of Thin Film Photovoltaic Cells

    E-Print Network [OSTI]

    Yao, Y. Lawrence

    :F, CdTe, solar cell INTRODUCTION Thin-film solar cell is a promising technology to achieve substrates. Cadmium telluride (CdTe) is the dominant thin film solar cell material in recent years because manufacturing processes in the fabrication of thin film solar cells is monolithic cell isolation and series

  8. CARRIER COLLECTION IN THIN-FILM CDTE SOLAR CELLS: THEORY AND EXPERIMENT

    E-Print Network [OSTI]

    CARRIER COLLECTION IN THIN-FILM CDTE SOLAR CELLS: THEORY AND EXPERIMENT A.E. Delahoy, Z. Cheng different wavelengths. Keywords: CdTe, thin film solar cell, modeling 1 INTRODUCTION Traditional Si p, Jsc, is independent of voltage, i.e. superposition holds. Thin film CdTe solar cells deviate from

  9. Enhanced efficiency of thin film solar cells using a shifted dual grating plasmonic structure

    E-Print Network [OSTI]

    Levy, Uriel

    Enhanced efficiency of thin film solar cells using a shifted dual grating plasmonic structure Ronen, "Light absorption enhancement in thin-film solar cells using whispering gallery modes in dielectric in thin film solar cells," Appl. Phys. Lett. 99(13), 131114 (2011). 10. H. R. Stuart and D. G. Hall

  10. Light trapping in thin-film solar cells with randomly rough and hybrid

    E-Print Network [OSTI]

    Light trapping in thin-film solar cells with randomly rough and hybrid textures Piotr Kowalczewski. M. Smets, and M. Zeman, "Plasmonic light trapping in thin-film silicon solar cells with improved Lambertian limits in thin film silicon solar cells with 1D and 2D periodic patterns," Opt. Express 20, A224­A

  11. Engineering Gaussian disorder at rough interfaces for light trapping in thin-film solar cells

    E-Print Network [OSTI]

    Engineering Gaussian disorder at rough interfaces for light trapping in thin-film solar cells Piotr A theoretical study of randomly rough interfaces to obtain light trapping in thin-film silicon solar cells of thin-film solar cells. © 2012 Optical Society of America OCIS codes: 040.5350, 050.1950. Reducing

  12. LBIC ANALYSIS OF THIN-FILM POLYCRYSTALLINE SOLAR CELLS James R. Sites and Timothy J. Nagle

    E-Print Network [OSTI]

    Sites, James R.

    LBIC ANALYSIS OF THIN-FILM POLYCRYSTALLINE SOLAR CELLS James R. Sites and Timothy J. Nagle Physics response map, was developed and used to map defects in thin-film solar cells [4]. Improvements to the two) measurements are providing a direct link between the spatial non-uniformities inherent in thin-film

  13. LOSS ANALYSIS OF BACK-CONTACT BACK-JUNCTION THIN-FILM MONOCRYSTALLINE SILICON SOLAR CELLS

    E-Print Network [OSTI]

    LOSS ANALYSIS OF BACK-CONTACT BACK-JUNCTION THIN-FILM MONOCRYSTALLINE SILICON SOLAR CELLS F. Haase losses in back-contact back- junction monocrystalline thin-film silicon solar cells. The cells are made for back-contact back- junction (BC BJ) monocrystalline thin-film silicon solar cells using the PSI process

  14. Light trapping in thin-film solar cells via scattering by nanostructured antireflection coatings

    E-Print Network [OSTI]

    Yu, Edward T.

    Light trapping in thin-film solar cells via scattering by nanostructured antireflection coatings X://jap.aip.org/authors #12;Light trapping in thin-film solar cells via scattering by nanostructured antireflection coatings X of nanostructured TiO2 layers fabricated on thin-film solar cells to provide, simultaneously, both antireflection

  15. Mechanics of thin-film transistors and solar cells on flexible substrates

    E-Print Network [OSTI]

    Suo, Zhigang

    Mechanics of thin-film transistors and solar cells on flexible substrates Helena Gleskova a,*, I be minimized throughout the fab- rication process. Amorphous silicon thin-film transistors and solar cells rights reserved. Keywords: Amorphous silicon; Thin-film transistor; Solar cell; Flexible electronics 1

  16. Dielectric back scattering patterns for light trapping in thin-film Si solar cells

    E-Print Network [OSTI]

    Polman, Albert

    Dielectric back scattering patterns for light trapping in thin-film Si solar cells M. van Lare,1 of dielectric and metallic backscattering patterns in thin-film a-Si:H solar cells. We compare devices for Light Trapping in Thin-Film Silicon Solar Cells", in Proceedings of the 23rd European Photovoltaic Solar

  17. Light trapping regimes in thin-film silicon solar cells with a photonic pattern

    E-Print Network [OSTI]

    Light trapping regimes in thin-film silicon solar cells with a photonic pattern Simone Zanotto a theoretical study of crystalline and amorphous silicon thin-film solar cells with a periodic pattern on a sub. Poortmans and V. Arkhipov (editors), Thin Film Solar Cells (Wiley, Chichester 2006). 4. P. W¨urfel, Physics

  18. BACK CONTACT MONOCRYSTALLINE THIN-FILM SILICON SOLAR CELLS FROM THE POROUS SILICON PROCESS

    E-Print Network [OSTI]

    BACK CONTACT MONOCRYSTALLINE THIN-FILM SILICON SOLAR CELLS FROM THE POROUS SILICON PROCESS F. Haase contact cells. Kraiem et al [7] made a back contact thin film monocrystalline solar cell with cell), Am Ohrberg 1, D-31860 Emmerthal, Germany ABSTRACT We develop a back contact monocrystalline thin-film

  19. ENGINEERED SUBSTRATES FOR THIN-FILM SOLAR CELLS: SCATTERING PROPERTIES OF 1D ROUGHNESS

    E-Print Network [OSTI]

    ENGINEERED SUBSTRATES FOR THIN-FILM SOLAR CELLS: SCATTERING PROPERTIES OF 1D ROUGHNESS S. Del Sorbo, Optical Properties, Substrates, Texturisation, Thin Film Solar Cells 1 MOTIVATION OF THIS WORK The aim of thin film technology is to reduce both the electrical transport losses in the bulk region of a solar

  20. Preparation and characterization of TL-based superconducting thin films 

    E-Print Network [OSTI]

    Wang, Pingshu

    1995-01-01

    A simple method for growth of Tl-based superconducting thin films is described. In this method, the precursor was prepared in a vacuum chamber by deposition of Ba, Ca and Cu metals or a Ba-Ca alloy and Cu metal. The precursor was then oxidized...

  1. Atomic layer deposition of superparamagnetic and ferrimagnetic magnetite thin films

    SciTech Connect (OSTI)

    Zhang, Yijun; Liu, Ming E-mail: wren@mail.xjtu.edu.cn Ren, Wei E-mail: wren@mail.xjtu.edu.cn; Zhang, Yuepeng; Chen, Xing; Ye, Zuo-Guang E-mail: wren@mail.xjtu.edu.cn

    2015-05-07

    One of the key challenges in realizing superparamagnetism in magnetic thin films lies in finding a low-energy growth way to create sufficiently small grains and magnetic domains which allow the magnetization to randomly and rapidly reverse. In this work, well-defined superparamagnetic and ferrimagnetic Fe{sub 3}O{sub 4} thin films are successfully prepared using atomic layer deposition technique by finely controlling the growth condition and post-annealing process. As-grown Fe{sub 3}O{sub 4} thin films exhibit a conformal surface and poly-crystalline nature with an average grain size of 7?nm, resulting in a superparamagnetic behavior with a blocking temperature of 210?K. After post-annealing in H{sub 2}/Ar at 400?°C, the as-grown ??Fe{sub 2}O{sub 3} sample is reduced to Fe{sub 3}O{sub 4} phase, exhibiting a ferrimagnetic ordering and distinct magnetic shape anisotropy. Atomic layer deposition of magnetite thin films with well-controlled morphology and magnetic properties provides great opportunities for integrating with other order parameters to realize magnetic nano-devices with potential applications in spintronics, electronics, and bio-applications.

  2. RF sputtered piezoelectric zinc oxide thin film for transducer applications

    E-Print Network [OSTI]

    Tang, William C

    parameters that could influence the quality of the resulting films include RF power, the ratio of argon depen- dency of the c-axis zinc oxide growth in radio-frequency sputtering system. Different deposition on the piezoelectric and crystalline qualities of the ZnO thin films. Experimental results showed that the multilayer

  3. Crystalline Thin Films Formed by Supramolecular Assembly for

    E-Print Network [OSTI]

    Gao, Hongjun

    Crystalline Thin Films Formed by Supramolecular Assembly for Ultrahigh-Density Data Storage with crystalline materials.[9] In contrast with small-mole- cule materials, supramolecular materials, which combine the benefits of polymers with those of organic crystalline systems, have been considered a promising medium

  4. Stress and Moisture Effects on Thin Film Buckling Delamination

    E-Print Network [OSTI]

    Volinsky, Alex A.

    ­2 GPa compres- sive residual stresses were sputter deposited on top of thin (below 100 nm) copperStress and Moisture Effects on Thin Film Buckling Delamination P. Waters & A.A. Volinsky Received, commonly called telephone cords, shown in Fig. 2 for the 1 2m W film on top of a 20 nm diamond-like carbon

  5. Synthesis and Characterization of Functional Nanostructured Zinc Oxide Thin Films

    E-Print Network [OSTI]

    Chow, Lee

    .1149/1.2357098, copyright The Electrochemical Society 65 #12;66 reduced environmental impact and a minimum undesirable inter-temperature thin film growth technique has been developed to fabricate a new generation of smart and functional and structural requirements of their applications in gas sensors and solar cells. The rapid photothermal

  6. Long-wave instabilities and saturation in thin film equations

    E-Print Network [OSTI]

    Pugh, Mary

    to shorter wavelengths which then dissipate the energy. The nonlinearity in the KS equation is advective.2) The equation arises as an interface model in bio-fluids [15], solar convec- tion [19], and binary alloys [48Long-wave instabilities and saturation in thin film equations A. L. Bertozzi Department

  7. Longwave instabilities and saturation in thin film equations

    E-Print Network [OSTI]

    Pugh, Mary

    then dissipate the energy. The nonlinearity in the KS equation is advective, and a#ects the dy­ namics di.2) The equation arises as an interface model in bio­fluids [15], solar convec­ tion [19], and binary alloys [48Long­wave instabilities and saturation in thin film equations A. L. Bertozzi Department

  8. Perovskite phase thin films and method of making

    DOE Patents [OSTI]

    Boyle, Timothy J. (Albuquerque, NM); Rodriguez, Mark A. (Albuquerque, NM)

    2000-01-01

    The present invention comprises perovskite-phase thin films, of the general formula A.sub.x B.sub.y O.sub.3 on a substrate, wherein A is selected from beryllium, magnesium, calcium, strontium, and barium or a combination thereof; B is selected from niobium and tantalum or a combination thereof; and x and y are mole fractions between approximately 0.8 and 1.2. More particularly, A is strontium or barium or a combination thereof and B is niobium or tantalum or a combination thereof. Also provided is a method of making a perovskite-phase thin film, comprising combining at least one element-A-containing compound, wherein A is selected from beryllium, magnesium, calcium, strontium or barium, with at least one element-B-containing compound, wherein B niobium or tantalum, to form a solution; adding a solvent to said solution to form another solution; spin-coating the solution onto a substrate to form a thin film; and heating the film to form the perovskite-phase thin film.

  9. Communications to the Editor Thin-Film Differential Scanning

    E-Print Network [OSTI]

    Allen, Leslie H.

    -mail: L-ALLEN9@uiuc.edu. Figure 1. MEMS-based calorimetric sensor for TDSC (not to scale). Volume 35. In this paper we demonstrate a recently developed MEMS-based thin-film differential scanning calorimetry (TDSC a microfabricated sensor shown in Figure 1 as a calorimetric cell. The sensor consists of a Si3Nx membrane supported

  10. Enhanced Superconducting Properties of Iron Chalcogenide Thin Films 

    E-Print Network [OSTI]

    Chen, Li

    2013-07-26

    phase have been studied and correlated with the superconducting properties. Second, we reported our initial attempt on introducing the flux pinning centers into FeSe_0.5Te_0.5 thin films either under a controlled oxygen atmosphere or with a thin CeO_2...

  11. Progress in High-Performance PV: Polycrystalline Thin-Film Tandem Cells

    SciTech Connect (OSTI)

    Symko-Davies, M.

    2004-08-01

    The High-Performance Photovoltaic (HiPerf PV) Project was initiated by the U.S. Department of Energy to substantially increase the viability of PV for cost-competitive applications. The goal is that PV will contribute significantly to the U.S. and world energy supply and environmental enhancement in the 21st century. The HiPerf PV Project aims at exploring the ultimate performance limits of existing PV technologies, approximately doubling their sunlight-to-electricity conversion efficiencies during its course, to accelerate and enhance their impact in the marketplace. To accomplish this, the National Center for Photovoltaics (NCPV) directs in-house and subcontracted research in high-performance polycrystalline thin-film and multijunction concentrator devices. This paper will describe progress of the subcontractor and in-house R&D on critical pathways for a PV technology having a high potential to reach cost-competitiveness goals: 25%-efficient, low-cost polycrystalline thin-film tandems for large-area, flat-plate modules.

  12. The influence of thermal treatment on the preparation of PMN and PMN-PT thin films

    SciTech Connect (OSTI)

    Spagnol, P.D.; Valadares, L.F.; Varela, J.A.; Bertochi, M.A.Z

    2003-03-15

    Ferroelectric thin films belong to a class of materials with great technological importance in optic fibers, microelectromechanical systems, and microprocessors and computers memories. The (1-x)PbMg{sub 1/3}Nb{sub 2/3}O{sub 3}(x)PbTiO{sub 3} (PMN-PT) thin films, with x=0, 0.1, 0.35 and 0.5, were prepared by Pechini's process and deposited by spin-coating on Si(100), Pt/Ti/SiO{sub 2}/Si(100) and quartz substrates. The goal of the present paper is to verify the thermal treatment influence on the perovskite phase formation, which is desirable for these applications. The phase formation was analyzed by X-ray diffraction. The film's surface was characterized by atomic force microscopy to analyze the roughness and the homogeneity. The results of this study indicate that the optimum conditions for obtaining the perovskite phase using a Pt/Ti/SiO{sub 2}/Si(100) substrate, were drying each deposited layer at 140 deg. C (heating plate), and a final thermal treatment at 600 deg. C for 3 h in a closed system with a lead-rich atmosphere.

  13. Abstract--In this paper, the propagation characteristics of an enhanced-thickness magnetic nanoparticle thin film are

    E-Print Network [OSTI]

    Tentzeris, Manos

    nanoparticle thin film are investigated on high resistivity silicon substrate (10,000 ohm-cm) for the first time up to 60 GHz. Contrary to other thin films, this nanoparticle thin film can achieve a thickness up to several hundred nanometers, even to micron. The enhanced thickness of this thin film is achieved

  14. Thin film photovoltaic device and process of manufacture

    DOE Patents [OSTI]

    Albright, Scot P. (Lakewood, CO); Chamberlin, Rhodes (El Paso, TX)

    1999-02-09

    Provided is a thin film photovoltaic device and a method of manufacturing the device. The thin film photovoltaic device comprises a film layer having particles which are smaller than about 30 microns in size held in an electrically insulating matrix material to reduce the potential for electrical shorting through the film layer. The film layer may be provided by depositing preformed particles onto a surrogate substrate and binding the particles in a film-forming matrix material to form a flexible sheet with the film layer. The flexible sheet may be separated from the surrogate substrate and cut into flexible strips. A plurality of the flexible strips may be located adjacent to and supported by a common supporting substrate to form a photovoltaic module having a plurality of electrically interconnected photovoltaic cells.

  15. Thin film photovoltaic device and process of manufacture

    DOE Patents [OSTI]

    Albright, Scot P. (Lakewood, CO); Chamberlin, Rhodes (El Paso, TX)

    1997-10-07

    Provided is a thin film photovoltaic device and a method of manufacturing the device. The thin film photovoltaic device comprises a film layer having particles which are smaller than about 30 microns in size held in an electrically insulating matrix material to reduce the potential for electrical shorting through the film layer. The film layer may be provided by depositing preformed particles onto a surrogate substrate and binding the particles in a film-forming matrix material to form a flexible sheet with the film layer. The flexible sheet may be separated from the surrogate substrate and cut into flexible strips. A plurality of the flexible strips may be located adjacent to and supported by a common supporting substrate to form a photovoltaic module having a plurality of electrically interconnected photovoltaic cells.

  16. Thin-Film Reliability Trends Toward Improved Stability: Preprint

    SciTech Connect (OSTI)

    Jordan, D. C.; Kurtz, S. R.

    2011-07-01

    Long-term, stable performance of photovoltaic (PV) modules will be increasingly important to their successful penetration of the power grid. This paper summarizes more than 150 thin-film and more than 1700 silicon PV degradation rates (Rd) quoted in publications for locations worldwide. Partitioning the literature results by technology and date of installation statistical analysis shows an improvement in degradation rate especially for thin-film technologies in the last decade. A CIGS array deployed at NREL for more than 5 years that appears to be stable supports the literature trends. Indoor and outdoor data indicate undetectable change in performance (0.2+/-0.2 %/yr). One module shows signs of slight degradation from what appears to be an initial manufacturing defect, however it has not affected the overall system performance.

  17. Eddy Current Testing for Detecting Small Defects in Thin Films

    SciTech Connect (OSTI)

    Obeid, Simon; Tranjan, Farid M. [Electrical and Computer Engineering Department, UNCC (United States); Dogaru, Teodor [Albany Instruments, 426-O Barton Creek, Charlotte, NC 28262 (United States)

    2007-03-21

    Presented here is a technique of using Eddy Current based Giant Magneto-Resistance sensor (GMR) to detect surface and sub-layered minute defects in thin films. For surface crack detection, a measurement was performed on a copper metallization of 5-10 microns thick. It was done by scanning the GMR sensor on the surface of the wafer that had two scratches of 0.2 mm, and 2.5 mm in length respectively. In another experiment, metal coatings were deposited over the layers containing five defects with known lengths such that the defects were invisible from the surface. The limit of detection (resolution), in terms of defect size, of the GMR high-resolution Eddy Current probe was studied using this sample. Applications of Eddy Current testing include detecting defects in thin film metallic layers, and quality control of metallization layers on silicon wafers for integrated circuits manufacturing.

  18. Thin film battery and method for making same

    DOE Patents [OSTI]

    Bates, John B. (Oak Ridge, TN); Dudney, Nancy J. (Knoxville, TN); Gruzalski, Greg R. (Oak Ridge, TN); Luck, Christopher F. (Knoxville, TN)

    1994-01-01

    Described is a thin-film battery, especially a thin-film microbattery, and a method for making same having application as a backup or primary integrated power source for electronic devices. The battery includes a novel electrolyte which is electrochemically stable and does not react with the lithium anode and a novel vanadium oxide cathode Configured as a microbattery, the battery can be fabricated directly onto a semiconductor chip, onto the semiconductor die or onto any portion of the chip carrier. The battery can be fabricated to any specified size or shape to meet the requirements of a particular application. The battery is fabricated of solid state materials and is capable of operation between -15.degree. C. and 150.degree. C.

  19. Characterization of Thin Films by XAFS: Application to Spintronics Materials

    SciTech Connect (OSTI)

    Heald, Steve M.; Kaspar, Tiffany C.; Droubay, Timothy C.; Chambers, Scott A.

    2009-10-25

    X-ray absorption fine structure (XAFS) has proven very valuable in characterizing thin films. This is illustrated with some examples from the area of diluted magnetic semiconductor (DMS) materials for spintronics applications. A promising route to DMS materials is doping of oxides such as TiO2 and ZnO with magnetic atoms such as Co. These can be grown as epitaxial thin films on various substrates. XAFS is especially valuable for characterizing the dopant atoms. The near edge region is sensitive to the symmetry of the bonding and valence of the dopants, and the extended XAFS can determine the details of the lattice site. XAFS is also valuable for detecting metallic nanoparticles. These can be difficult to detect by other methods, and can give a spurious magnetic signal. The power of XAFS is illustrated by examples from studies on Co doped ZnO films.

  20. Thin film photovoltaic device and process of manufacture

    DOE Patents [OSTI]

    Albright, S.P.; Chamberlin, R.

    1999-02-09

    Provided is a thin film photovoltaic device and a method of manufacturing the device. The thin film photovoltaic device comprises a film layer having particles which are smaller than about 30 microns in size held in an electrically insulating matrix material to reduce the potential for electrical shorting through the film layer. The film layer may be provided by depositing preformed particles onto a surrogate substrate and binding the particles in a film-forming matrix material to form a flexible sheet with the film layer. The flexible sheet may be separated from the surrogate substrate and cut into flexible strips. A plurality of the flexible strips may be located adjacent to and supported by a common supporting substrate to form a photovoltaic module having a plurality of electrically interconnected photovoltaic cells. 13 figs.

  1. Thin film photovoltaic device and process of manufacture

    DOE Patents [OSTI]

    Albright, S.P.; Chamberlin, R.

    1997-10-07

    Provided is a thin film photovoltaic device and a method of manufacturing the device. The thin film photovoltaic device comprises a film layer having particles which are smaller than about 30 microns in size held in an electrically insulating matrix material to reduce the potential for electrical shorting through the film layer. The film layer may be provided by depositing preformed particles onto a surrogate substrate and binding the particles in a film-forming matrix material to form a flexible sheet with the film layer. The flexible sheet may be separated from the surrogate substrate and cut into flexible strips. A plurality of the flexible strips may be located adjacent to and supported by a common supporting substrate to form a photovoltaic module having a plurality of electrically interconnected photovoltaic cells. 13 figs.

  2. Thin film battery and method for making same

    DOE Patents [OSTI]

    Bates, J.B.; Dudney, N.J.; Gruzalski, G.R.; Luck, C.F.

    1994-08-16

    Described is a thin-film battery, especially a thin-film microbattery, and a method for making same having application as a backup or primary integrated power source for electronic devices. The battery includes a novel electrolyte which is electrochemically stable and does not react with the lithium anode and a novel vanadium oxide cathode. Configured as a microbattery, the battery can be fabricated directly onto a semiconductor chip, onto the semiconductor die or onto any portion of the chip carrier. The battery can be fabricated to any specified size or shape to meet the requirements of a particular application. The battery is fabricated of solid state materials and is capable of operation between [minus]15 C and 150 C. 9 figs.

  3. Method for formation of thin film transistors on plastic substrates

    DOE Patents [OSTI]

    Carey, P.G.; Smith, P.M.; Sigmon, T.W.; Aceves, R.C.

    1998-10-06

    A process for formation of thin film transistors (TFTs) on plastic substrates replaces standard thin film transistor fabrication techniques, and uses sufficiently lower processing temperatures so that inexpensive plastic substrates may be used in place of standard glass, quartz, and silicon wafer-based substrates. The process relies on techniques for depositing semiconductors, dielectrics, and metals at low temperatures; crystallizing and doping semiconductor layers in the TFT with a pulsed energy source; and creating top-gate self-aligned as well as back-gate TFT structures. The process enables the fabrication of amorphous and polycrystalline channel silicon TFTs at temperatures sufficiently low to prevent damage to plastic substrates. The process has use in large area low cost electronics, such as flat panel displays and portable electronics. 5 figs.

  4. Method for formation of thin film transistors on plastic substrates

    DOE Patents [OSTI]

    Carey, Paul G. (Mountain View, CA); Smith, Patrick M. (San Ramon, CA); Sigmon, Thomas W. (Portola Valley, CA); Aceves, Randy C. (Livermore, CA)

    1998-10-06

    A process for formation of thin film transistors (TFTs) on plastic substrates replaces standard thin film transistor fabrication techniques, and uses sufficiently lower processing temperatures so that inexpensive plastic substrates may be used in place of standard glass, quartz, and silicon wafer-based substrates. The process relies on techniques for depositing semiconductors, dielectrics, and metals at low temperatures; crystallizing and doping semiconductor layers in the TFT with a pulsed energy source; and creating top-gate self-aligned as well as back-gate TFT structures. The process enables the fabrication of amorphous and polycrystalline channel silicon TFTs at temperatures sufficiently low to prevent damage to plastic substrates. The process has use in large area low cost electronics, such as flat panel displays and portable electronics.

  5. TI--CR--AL--O thin film resistors

    DOE Patents [OSTI]

    Jankowski, Alan F. (Livermore, CA); Schmid, Anthony P. (Solana Beach, CA)

    2000-01-01

    Thin films of Ti--Cr--Al--O are used as a resistor material. The films are rf sputter deposited from ceramic targets using a reactive working gas mixture of Ar and O.sub.2. Resistivity values from 10.sup.4 to 10.sup.10 Ohm-cm have been measured for Ti--Cr--Al--O film <1 .mu.m thick. The film resistivity can be discretely selected through control of the target composition and the deposition parameters. The application of Ti--Cr--Al--O as a thin film resistor has been found to be thermodynamically stable, unlike other metal-oxide films. The Ti--Cr--Al--O film can be used as a vertical or lateral resistor, for example, as a layer beneath a field emission cathode in a flat panel display; or used to control surface emissivity, for example, as a coating on an insulating material such as vertical wall supports in flat panel displays.

  6. Status of High Performance PV: Polycrystalline Thin-Film Tandems

    SciTech Connect (OSTI)

    Symko-Davies, M.

    2005-02-01

    The High-Performance Photovoltaic (HiPerf PV) Project was initiated by the U.S. Department of Energy to substantially increase the viability of photovoltaics (PV) for cost-competitive applications so that PV can contribute significantly to our energy supply and our environment. The HiPerf PV Project aims at exploring the ultimate performance limits of existing PV technologies, approximately doubling their sunlight-to-electricity conversion efficiencies during its course. This work includes bringing thin-film cells and modules toward 25% and 20% efficiencies, respectively, and developing multijunction concentrator cells and modules able to convert more than one-third of the sun's energy to electricity (i.e., 33% efficiency). This paper will address recent accomplishments of the NREL in-house research effort involving polycrystalline thin-film tandems, as well as the research efforts under way in the subcontracted area.

  7. Preparation of LiMn{sub 2}O{sub 4} cathode thin films for thin film lithium secondary batteries by a mist CVD process

    SciTech Connect (OSTI)

    Tadanaga, Kiyoharu, E-mail: tadanaga@chem.osakafu-u.ac.jp [Department of Applied Chemistry, Graduate School of Engineering, Osaka Prefecture University, Sakai, Osaka, 599-8531 (Japan); Yamaguchi, Akihiro; Sakuda, Atsushi; Hayashi, Akitoshi; Tatsumisago, Masahiro [Department of Applied Chemistry, Graduate School of Engineering, Osaka Prefecture University, Sakai, Osaka, 599-8531 (Japan); Duran, Alicia; Aparacio, Mario [Instituto de Cerámica y Vidrio, Consejo Superior de Investigaciones Científicas, Kelsen 5 (Campus de Cantoblanco), Madrid, 28049 (Spain)

    2014-05-01

    Highlights: • LiMn{sub 2}O{sub 4} thin films were prepared by using the mist CVD process. • An aqueous solution of lithium and manganese acetates is used for the precursor solution. • The cell with the LiMn{sub 2}O{sub 4} thin films exhibited a capacity of about 80 mAh/g. • The cell showed good cycling performance during 10 cycles. - Abstract: LiMn{sub 2}O{sub 4} cathode thin films for thin film lithium secondary batteries were prepared by using so-called the “mist CVD process”, employing an aqueous solution of lithium acetate and manganese acetate, as the source of Li and Mn, respectively. The aqueous solution of starting materials was ultrasonically atomized to form mist particles, and mists were transferred by nitrogen gas to silica glass substrate to form thin films. FE-SEM observation revealed that thin films obtained by this process were dense and smooth, and thin films with a thickness of about 750 nm were obtained. The electrochemical cell with the thin films obtained by sintering at 700 °C exhibited a capacity of about 80 mAh/g, and the cell showed good cycling performance during 10 cycles.

  8. Synthesis of thin films and materials utilizing a gaseous catalyst

    DOE Patents [OSTI]

    Morse, Daniel E; Schwenzer, Birgit; Gomm, John R; Roth, Kristian M; Heiken, Brandon; Brutchey, Richard

    2013-10-29

    A method for the fabrication of nanostructured semiconducting, photoconductive, photovoltaic, optoelectronic and electrical battery thin films and materials at low temperature, with no molecular template and no organic contaminants. High-quality metal oxide semiconductor, photovoltaic and optoelectronic materials can be fabricated with nanometer-scale dimensions and high dopant densities through the use of low-temperature biologically inspired synthesis routes, without the use of any biological or biochemical templates.

  9. Substrates suitable for deposition of superconducting thin films

    DOE Patents [OSTI]

    Feenstra, Roeland (Oak Ridge, TN); Boatner, Lynn A. (Oak Ridge, TN)

    1993-01-01

    A superconducting system for the lossless transmission of electrical current comprising a thin film of superconducting material Y.sub.1 Ba.sub.2 Cu.sub.3 O.sub.7-x epitaxially deposited upon a KTaO.sub.3 substrate. The KTaO.sub.3 is an improved substrate over those of the prior art since the it exhibits small lattice constant mismatch and does not chemically react with the superconducting film.

  10. A comparison of thick film and thin film traffic stripes 

    E-Print Network [OSTI]

    Keese, Charles J

    1952-01-01

    of this thesis. CONTESTS Introduction ~ ~ ~ ~ ~ 1 Scope and Obfectives Method of Conducting Road Service Tests ~ ~ ~ ~ ~ ~ ~ ~ 7 ~ ~ ~ ~ ~ ~ ~ ~ ~ 8 PART I A Comparison of Paint Films of Various Thicknesses . . . . . . . . ~ ~, ~, ~ 72 App1ioation... of Test Stripes . Results of Thiokness Tests . 13 19 Conclusions 2$ PART II A Comparison of Various Thick Film and Thin Film Traffic Stripes. 26 Paint Stripes Over Adhesive Films Rosin Striping Compounds. . . + ~ . , ~ 29 ~ ~ ~ Preforsmd Plastic...

  11. Preparation of redox polymer cathodes for thin film rechargeable batteries

    DOE Patents [OSTI]

    Skotheim, T.A.; Lee, H.S.; Okamoto, Yoshiyuki.

    1994-11-08

    The present invention relates to the manufacture of thin film solid state electrochemical devices using composite cathodes comprising a redox polymer capable of undergoing oxidation and reduction, a polymer solid electrolyte and conducting carbon. The polymeric cathode material is formed as a composite of radiation crosslinked polymer electrolytes and radiation crosslinked redox polymers based on polysiloxane backbones with attached organosulfur side groups capable of forming sulfur-sulfur bonds during electrochemical oxidation.

  12. Fabrication and testing of thermoelectric thin film devices

    SciTech Connect (OSTI)

    Wagner, A.V.; Foreman, R.J.; Summers, L.J.; Barbee, T.W. Jr.; Farmer, J.C. [Lawrence Livermore National Lab., CA (United States). Chemistry and Materials Science Dept.

    1996-03-01

    Two thin-film thermoelectric devices are experimentally demonstrated. The relevant thermal loads on the cold junction of these devices are determined. The analytical form of the equation that describes the thermal loading of the device enables one to model the performance based on the independently measured electronic properties of the films forming the devices. This model elucidates which parameters determine device performance, and how they can be used to maximize performance.

  13. Experimental thin film deposition and surface analysis techniques

    SciTech Connect (OSTI)

    Collins, W.E.; Rambabu, B.

    1986-01-01

    An attempt has been made to present some of the thin-film deposition and surface analysis techniques which may be useful in growing superionic conducting materials. Emphasis is made on the importance of being careful in selecting process parameters and materials in order to produce films with properties outlined in this article. Also, special care should be given to proper consideration of grain boundary effects.

  14. Thin film composition with biological substance and method of making

    DOE Patents [OSTI]

    Campbell, Allison A. (Kennewick, WA); Song, Lin (Richland, WA)

    1999-01-01

    The invention provides a thin-film composition comprising an underlying substrate of a first material including a plurality of attachment sites; a plurality of functional groups chemically attached to the attachment sites of the underlying substrate; and a thin film of a second material deposited onto the attachment sites of the underlying substrate, and a biologically active substance deposited with the thin-film. Preferably the functional groups are attached to a self assembling monolayer attached to the underlying substrate. Preferred functional groups attached to the underlying substrate are chosen from the group consisting of carboxylates, sulfonates, phosphates, optionally substituted, linear or cyclo, alkyl, alkene, alkyne, aryl, alkylaryl, amine, hydroxyl, thiol, silyl, phosphoryl, cyano, metallocenyl, carbonyl, and polyphosphate. Preferred materials for the underlying substrate are selected from the group consisting of a metal, a metal alloy, a plastic, a polymer, a proteic film, a membrane, a glass or a ceramic. The second material is selected from the group consisting of inorganic crystalline structures, inorganic amorphus structures, organic crystalline structures, and organic amorphus structures. Preferred second materials are phosphates, especially calcium phosphates and most particularly calcium apatite. The biologically active molecule is a protein, peptide, DNA segment, RNA segment, nucleotide, polynucleotide, nucleoside, antibiotic, antimicrobal, radioisotope, chelated radioisotope, chelated metal, metal salt, anti-inflamatory, steriod, nonsteriod anti-inflammatory, analgesic, antihistamine, receptor binding agent, or chemotherapeutic agent, or other biologically active material. Preferably the biologically active molecule is an osteogenic factor the compositions listed above.

  15. Thin film composition with biological substance and method of making

    SciTech Connect (OSTI)

    Campbell, A.A.; Song, L.

    1999-09-28

    The invention provides a thin-film composition comprising an underlying substrate of a first material including a plurality of attachment sites; a plurality of functional groups chemically attached to the attachment sites of the underlying substrate; and a thin film of a second material deposited onto the attachment sites of the underlying substrate, and a biologically active substance deposited with the thin-film. Preferably the functional groups are attached to a self assembling monolayer attached to the underlying substrate. Preferred functional groups attached to the underlying substrate are chosen from the group consisting of carboxylates, sulfonates, phosphates, optionally substituted, linear or cyclo, alkyl, alkene, alkyne, aryl, alkylaryl, amine, hydroxyl, thiol, silyl, phosphoryl, cyano, metallocenyl, carbonyl, and polyphosphate. Preferred materials for the underlying substrate are selected from the group consisting of a metal, a metal alloy, a plastic, a polymer, a proteic film, a membrane, a glass or a ceramic. The second material is selected from the group consisting of inorganic crystalline structures, inorganic amorphous structures, organic crystalline structures, and organic amorphous structures. Preferred second materials are phosphates, especially calcium phosphates and most particularly calcium apatite. The biologically active molecule is a protein, peptide, DNA segment, RNA segment, nucleotide, polynucleotide, nucleoside, antibiotic, antimicrobial, radioisotope, chelated radioisotope, chelated metal, metal salt, anti-inflammatory, steroid, nonsteroid anti-inflammatory, analgesic, antihistamine, receptor binding agent, or chemotherapeutic agent, or other biologically active material. Preferably the biologically active molecule is an osteogenic factor consisting of the compositions listed above.

  16. Geometric shape control of thin film ferroelectrics and resulting structures

    DOE Patents [OSTI]

    McKee, Rodney A. (Kingston, TN); Walker, Frederick J. (Oak Ridge, TN)

    2000-01-01

    A monolithic crystalline structure and a method of making involves a semiconductor substrate, such as silicon, and a ferroelectric film, such as BaTiO.sub.3, overlying the surface of the substrate wherein the atomic layers of the ferroelectric film directly overlie the surface of the substrate. By controlling the geometry of the ferroelectric thin film, either during build-up of the thin film or through appropriate treatment of the thin film adjacent the boundary thereof, the in-plane tensile strain within the ferroelectric film is relieved to the extent necessary to permit the ferroelectric film to be poled out-of-plane, thereby effecting in-plane switching of the polarization of the underlying substrate material. The method of the invention includes the steps involved in effecting a discontinuity of the mechanical restraint at the boundary of the ferroelectric film atop the semiconductor substrate by, for example, either removing material from a ferroelectric film which has already been built upon the substrate, building up a ferroelectric film upon the substrate in a mesa-shaped geometry or inducing the discontinuity at the boundary by ion beam deposition techniques.

  17. MEMS-based thin-film fuel cells

    DOE Patents [OSTI]

    Jankowksi, Alan F.; Morse, Jeffrey D.

    2003-10-28

    A micro-electro-mechanical systems (MEMS) based thin-film fuel cells for electrical power applications. The MEMS-based fuel cell may be of a solid oxide type (SOFC), a solid polymer type (SPFC), or a proton exchange membrane type (PEMFC), and each fuel cell basically consists of an anode and a cathode separated by an electrolyte layer. Additionally catalyst layers can also separate the electrodes (cathode and anode) from the electrolyte. Gas manifolds are utilized to transport the fuel and oxidant to each cell and provide a path for exhaust gases. The electrical current generated from each cell is drawn away with an interconnect and support structure integrated with the gas manifold. The fuel cells utilize integrated resistive heaters for efficient heating of the materials. By combining MEMS technology with thin-film deposition technology, thin-film fuel cells having microflow channels and full-integrated circuitry can be produced that will lower the operating temperature an will yield an order of magnitude greater power density than the currently known fuel cells.

  18. Deuterium phase behavior in thin-film Pd

    SciTech Connect (OSTI)

    Munter, A.E.; Heuser, B.J.

    1998-07-01

    The absorption of deuterium from the gas phase into two Pd thin films 668 {Angstrom} and 1207 {Angstrom} thick was measured at room temperature with {ital in situ} neutron reflectometry. Room-temperature solubility isothermal curves, out-of-plane film expansion, and deuterium depth profiles were determined from fits to the neutron reflectivity data. The measurements demonstrate that the deuterium solubility behavior, both in solid solution and within the two-phase region, is strongly perturbed by the thin-film geometry, consistent with previous solubility measurements in the published literature. The phase behavior investigated here was observed to depend on film thickness and on deuterium cycling through the two-phase region. The 668-{Angstrom} film exhibited the greatest initial phase perturbation and most significant changes upon cycling. Upon repeated cycling, both films approach nearly identical deuterium isothermal solubility and out-of-plane expansion behaviors. The observed equilibrium out-of-plane expansion behavior was consistent with the films expanding under an in-plane clamping constraint imposed by the substrate. The effect of this substrate constraining force is to amplify the out-of-plane expansion beyond that expected in bulk Pd. Taken together, these measurements implicate the film/substrate interfacial clamping interaction as the origin of the perturbed hydrogen phase behavior in thin-film geometry. {copyright} {ital 1998} {ital The American Physical Society}

  19. Methods for fabricating thin film III-V compound solar cell

    DOE Patents [OSTI]

    Pan, Noren; Hillier, Glen; Vu, Duy Phach; Tatavarti, Rao; Youtsey, Christopher; McCallum, David; Martin, Genevieve

    2011-08-09

    The present invention utilizes epitaxial lift-off in which a sacrificial layer is included in the epitaxial growth between the substrate and a thin film III-V compound solar cell. To provide support for the thin film III-V compound solar cell in absence of the substrate, a backing layer is applied to a surface of the thin film III-V compound solar cell before it is separated from the substrate. To separate the thin film III-V compound solar cell from the substrate, the sacrificial layer is removed as part of the epitaxial lift-off. Once the substrate is separated from the thin film III-V compound solar cell, the substrate may then be reused in the formation of another thin film III-V compound solar cell.

  20. May 2003 NREL/CP-520-33933 Amorphous and Thin-Film

    E-Print Network [OSTI]

    Deng, Xunming

    May 2003 · NREL/CP-520-33933 Amorphous and Thin-Film Silicon B.P. Nelson, H.A. Atwater, B. von and Thin-Film Silicon Brent P. Nelson,1 Harry A. Atwater,2 Bolko von Roedern,1 Jeff Yang,3 Paul Sims,4 in the Amorphous and Thin-Film Silicon session at the National Center for Photovoltaics and Solar Program Review

  1. Deployable telescope having a thin-film mirror and metering structure

    DOE Patents [OSTI]

    Krumel, Leslie J. (Cedar Crest, NM); Martin, Jeffrey W. (Albuquerque, NM)

    2010-08-24

    A deployable thin-film mirror telescope comprises a base structure and a metering structure. The base structure houses a thin-film mirror, which can be rolled for stowage and unrolled for deployment. The metering structure is coupled to the base structure and can be folded for stowage and unfolded for deployment. In the deployed state, the unrolled thin-film mirror forms a primary minor for the telescope and the unfolded metering structure positions a secondary minor for the telescope.

  2. p-Doping limit and donor compensation in CdTe polycrystalline thin film solar cells

    E-Print Network [OSTI]

    p-Doping limit and donor compensation in CdTe polycrystalline thin film solar cells Ken K. Chin n substitution of Cd CuCd 0=À #12; #12; play critical roles in p-doping of CdTe in CdS/CdTe thin film solar cells in Fig. 1. As for the CdTe polycrystalline thin film in a CdS/CdTe solar cell, it is still being debated

  3. An approach to simultaneously test multiple devices for high-throughput production of thin film electronics

    E-Print Network [OSTI]

    Kumar, A.; Flewitt, A. J.

    2015-07-28

    of transparent flexible thin-film transistors using amorphous oxide semiconductors.,” Nature, vol. 432, no. 7016, pp. 488–492, 2004. [2] E. Fortunato, P. Barquinha, and R. Martins, “Oxide semiconductor thin-film transistors: a review of recent advances... , M. Lavine, and R. Coontz, “Looking Beyond Silicon,” Science, vol. 327, no. 5973. pp. 1595–1595, 2010. [6] A. J. Flewitt, “Hydrogenated Amorphous Silicon Thin Film Transistors (a Si:H TFTs),” Handbook of Visual Display Technology-Springer, 2012...

  4. Microwave plasma assisted supersonic gas jet deposition of thin film materials

    DOE Patents [OSTI]

    Schmitt, J.J. III; Halpern, B.L.

    1993-10-26

    An apparatus for fabricating thin film materials utilizing high speed gas dynamics relies on supersonic free jets of carrier gas to transport depositing vapor species generated in a microwave discharge to the surface of a prepared substrate where the vapor deposits to form a thin film. The present invention generates high rates of deposition and thin films of unforeseen high quality at low temperatures. 5 figures.

  5. DISSERTATION DEVICE PHYSICS OF Cu(In,Ga)Se2 THIN-FILM SOLAR CELLS

    E-Print Network [OSTI]

    Sites, James R.

    OF Cu(In,Ga)Se2 THIN-FILM SOLAR CELLS Thin-film solar cells have the potential to be an important contributor to the global energy demand by the mid-21st-century. Cu(In,Ga)Se2 (CIGS) solar cells, which haveDISSERTATION DEVICE PHYSICS OF Cu(In,Ga)Se2 THIN-FILM SOLAR CELLS Submitted by Markus Gloeckler

  6. Electrochromism vs. the Bugs:DevelopingWO3 Thin Film Windows...

    Office of Scientific and Technical Information (OSTI)

    Electrochromism vs. the Bugs:DevelopingWO3 Thin Film Windows toControl Photoactive Biological Systems. Citation Details In-Document Search Title: Electrochromism vs. the...

  7. Nonlinear optical characterization of ZnS thin film synthesized by chemical spray pyrolysis method

    SciTech Connect (OSTI)

    G, Sreeja V; Anila, E. I., E-mail: anilaei@gmail.com; R, Reshmi, E-mail: anilaei@gmail.com; John, Manu Punnan, E-mail: anilaei@gmail.com [Optolectronic and Nanomaterials Research Laboratory, Department of Physics, Union Christian College, Aluva-683 102, Kerala (India); V, Sabitha P; Radhakrishnan, P. [International School of Photonics, CUSAT, Cochin-22 (India)

    2014-10-15

    ZnS thin film was prepared by Chemical Spray Pyrolysis (CSP) method. The sample was characterized by X-ray diffraction method and Z scan technique. XRD pattern showed that ZnS thin film has hexagonal structure with an average size of about 5.6nm. The nonlinear optical properties of ZnS thin film was studied by open aperture Z-Scan technique using Q-switched Nd-Yag Laser at 532nm. The Z-scan plot showed that the investigated ZnS thin film has saturable absorption behavior. The nonlinear absorption coefficient and saturation intensity were also estimated.

  8. Investigation of the optical properties of MoS{sub 2} thin films...

    Office of Scientific and Technical Information (OSTI)

    ellipsometry Spectroscopic ellipsometry (SE) characterization of layered transition metal dichalcogenide (TMD) thin films grown by vapor phase sulfurization is reported. By...

  9. Durable silver thin film coating for diffraction gratings

    DOE Patents [OSTI]

    Wolfe, Jesse D. (Discovery Bay, CA); Britten, Jerald A. (Oakley, CA); Komashko, Aleksey M. (San Diego, CA)

    2006-05-30

    A durable silver film thin film coated non-planar optical element has been developed to replace Gold as a material for fabricating such devices. Such a coating and resultant optical element has an increased efficiency and is resistant to tarnishing, can be easily stripped and re-deposited without modifying underlying grating structure, improves the throughput and power loading of short pulse compressor designs for ultra-fast laser systems, and can be utilized in variety of optical and spectrophotometric systems, particularly high-end spectrometers that require maximized efficiency.

  10. Thin film solar cell including a spatially modulated intrinsic layer

    DOE Patents [OSTI]

    Guha, Subhendu (Troy, MI); Yang, Chi-Chung (Troy, MI); Ovshinsky, Stanford R. (Bloomfield Hills, MI)

    1989-03-28

    One or more thin film solar cells in which the intrinsic layer of substantially amorphous semiconductor alloy material thereof includes at least a first band gap portion and a narrower band gap portion. The band gap of the intrinsic layer is spatially graded through a portion of the bulk thickness, said graded portion including a region removed from the intrinsic layer-dopant layer interfaces. The band gap of the intrinsic layer is always less than the band gap of the doped layers. The gradation of the intrinsic layer is effected such that the open circuit voltage and/or the fill factor of the one or plural solar cell structure is enhanced.

  11. High-temperature superconducting thin-film-based electronic devices

    SciTech Connect (OSTI)

    Wu, X.D; Finokoglu, A.; Hawley, M.; Jia, Q.; Mitchell, T.; Mueller, F.; Reagor, D.; Tesmer, J.

    1996-09-01

    This the final report of a one-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The project involved optimization of processing of Y123 and Tl-2212 thin films deposited on novel substrates for advanced electronic devices. The Y123 films are the basis for development of Josephson Junctions to be utilized in magnetic sensors. Microwave cavities based on the Tl-2212 films are the basis for subsequent applications as communication antennas and transmitters in satellites.

  12. Thin film superconductors and process for making same

    DOE Patents [OSTI]

    Nigrey, P.J.

    1988-01-21

    A process for the preparation of oxide superconductors from high-viscosity non-aqueous solution is described. Solutions of lanthanide nitrates, alkaline earth nitrates and copper nitrates in a 1:2:3 stoichiometric ratio, when added to ethylene glycol containing citric acid solutions, have been used to prepare highly viscous non-aqueous solutions of metal mixed nitrates-citrates. Thin films of these compositions are produced when a layer of the viscous solution is formed on a substrate and subjected to thermal decomposition.

  13. Thin-Film Material Science and Processing | Materials Science | NREL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power AdministrationRobust,Field-effectWorking With U.S.Week DayDr. JeffreyThermalš ÐÓÔÑ ÒØ ÓworkThin-Film

  14. Study of plasma enhanced chemical vapor deposition of boron-doped hydrogenated amorphous silicon thin films and the application to p-channel thin film transistor 

    E-Print Network [OSTI]

    Nominanda, Helinda

    2004-01-01

    The material and process characteristics of boron doped hydrogenated amorphous silicon (a-Si:H) thin film deposited by plasma enhanced chemical vapor deposition technique (PECVD) have been studied. The goal is to apply the high quality films...

  15. Thin film cadmium telluride and zinc phosphide solar cells

    SciTech Connect (OSTI)

    Chu, T.

    1984-10-01

    This report describes research performed from June 1982 to October 1983 on the deposition of cadmium telluride films by direct combination of the cadmium and tellurium vapor on foreign substrates. Nearly stoichiometric p-type cadmium telluride films and arsenic-doped p-type films have been prepared reproducibly. Major efforts were directed to the deposition and characterization of heterojunction window materials, indium tin oxide, fluorine-doped tin oxide, cadmium oxide, and zinc oxide. A number of heterojunction solar cells were prepared, and the best thin-film ITO/CdTe solar cells had an AMl efficiency of about 7.2%. Zinc phosphide films were deposited on W/steel substrates by the reaction of zinc and phosphine in a hydrogen flow. Films without intentional doping had an electrical resistivity on the order of 10/sup 6/ ohm-cm, and this resistivity may be reduced to about 5 x 10/sup 4/ ohm-cm by adding hydrogen chloride or hydrogen bromide to the reaction mixture. Lower resistivity films were deposited by adding a controlled amount of silver nitrate solution on to the substrate surface. Major efforts were directed to the deposition of low-resistivity zinc selenide in order to prepare ZnSe/An/sub 3/P/sub 2/ heterojunction thin-film solar cells. However, zinc selenide films deposited by vacuum evaporation and chemical vapor deposition techniques were all of high resistivity.

  16. Silicon Oxynitride Thin Film Barriers for PV Packaging (Poster)

    SciTech Connect (OSTI)

    del Cueto, J. A.; Glick, S. H.; Terwilliger, K. M.; Jorgensen, G. J.; Pankow, J. W.; Keyes, B. M.; Gedvilas, L. M.; Pern, F. J.

    2006-10-03

    Dielectric, adhesion-promoting, moisture barriers comprised of silicon oxynitride thin film materials (SiOxNy with various material stoichiometric compositions x,y) were applied to: 1) bare and pre-coated soda-lime silicate glass (coated with transparent conductive oxide SnO2:F and/or aluminum), and polymer substrates (polyethylene terephthalate, PET, or polyethylene napthalate, PEN); plus 2) pre- deposited photovoltaic (PV) cells and mini-modules consisting of amorphous silicon (a-Si) and copper indium gallium diselenide (CIGS) thin-film PV technologies. We used plasma enhanced chemical vapor deposition (PECVD) process with dilute silane, nitrogen, and nitrous oxide/oxygen gas mixtures in a low-power (< or = 10 milliW per cm2) RF discharge at ~ 0.2 Torr pressure, and low substrate temperatures < or = 100(degrees)C, over deposition areas ~ 1000 cm2. Barrier properties of the resulting PV cells and coated-glass packaging structures were studied with subsequent stressing in damp-heat exposure at 85(degrees)C/85% RH. Preliminary results on PV cells and coated glass indicate the palpable benefits of the barriers in mitigating moisture intrusion and degradation of the underlying structures using SiOxNy coatings with thicknesses in the range of 100-200 nm.

  17. Comparative study of the mechanical properties of nanostructured thin films on stretchable substrates

    SciTech Connect (OSTI)

    Djaziri, S. [Max-Planck-Institut für Eisenforschung GmbH, Max-Planck-Straße 1, 40237 Düsseldorf (Germany); Institut P' (UPR 3346 CNRS), Université de Poitiers, ENSMA, Bd Pierre et Marie Curie, 86962 Futuroscope Cedex (France); Renault, P.-O.; Le Bourhis, E.; Goudeau, Ph., E-mail: Philippe.goudeau@univ-poitiers.fr [Institut P' (UPR 3346 CNRS), Université de Poitiers, ENSMA, Bd Pierre et Marie Curie, 86962 Futuroscope Cedex (France); Faurie, D. [LSPM, (UPR 3407 CNRS), Université Paris 13, Institut Galilée, 99 avenue Jean-Baptiste Clément, 93430 Villetaneuse (France); Geandier, G. [Institut Jean Lamour (UMR 3079 CNRS), Université de Lorraine, Parc de Saurupt, CS 50840, 54011 NANCY Cedex (France); Mocuta, C.; Thiaudière, D. [Synchrotron SOLEIL, L'Orme des Merisiers, Saint-Aubin, BP 48, 91192 Gif-sur-Yvette Cedex (France)

    2014-09-07

    Comparative studies of the mechanical behavior between copper, tungsten, and W/Cu nanocomposite based on copper dispersoïd thin films were performed under in-situ controlled tensile equi-biaxial loadings using both synchrotron X-ray diffraction and digital image correlation techniques. The films first deform elastically with the lattice strain equal to the true strain given by digital image correlation measurements. The Cu single thin film intrinsic elastic limit of 0.27% is determined below the apparent elastic limit of W and W/Cu nanocomposite thin films, 0.30% and 0.49%, respectively. This difference is found to be driven by the existence of as-deposited residual stresses. Above the elastic limit on the lattice strain-true strain curves, we discriminate two different behaviors presumably footprints of plasticity and fracture. The Cu thin film shows a large transition domain (0.60% true strain range) to a plateau with a smooth evolution of the curve which is associated to peak broadening. In contrast, W and W/Cu nanocomposite thin films show a less smooth and reduced transition domain (0.30% true strain range) to a plateau with no peak broadening. These observations indicate that copper thin film shows some ductility while tungsten/copper nanocomposites thin films are brittle. Fracture resistance of W/Cu nanocomposite thin film is improved thanks to the high compressive residual stress and the elimination of the metastable ?-W phase.

  18. Effects of Process Conditions on Properties of Electroplated Ni Thin Films for Microsystem Applications

    E-Print Network [OSTI]

    Fleck, Norman A.

    Effects of Process Conditions on Properties of Electroplated Ni Thin Films for Microsystem, Southampton SO17 1QJ, United Kingdom The properties of electroplated Ni thin films have been systematically, micromotors, and pneumatic actuators.3-11 Ni and NiFe are the electroplated metals most commonly used for MEMS

  19. Ambient induced degradation and chemically activated recovery in copper phthalocyanine thin film transistors

    E-Print Network [OSTI]

    Kummel, Andrew C.

    Ambient induced degradation and chemically activated recovery in copper phthalocyanine thin film 2009 The electrical degradation aging of copper phthalocyanine CuPc organic thin film transistors OTFTs of Physics. DOI: 10.1063/1.3159885 I. INTRODUCTION The recent demand for low cost, versatile electronic de

  20. Focused ion beam specimen preparation for electron holography of electrically biased thin film solar cells

    E-Print Network [OSTI]

    Dunin-Borkowski, Rafal E.

    solar cells M. Duchamp1 , M. den Hertog2 , R. Imlau1 , C. B. Boothroyd1 , A. Kovács1 , A. H. Tavabi1, biased TEM specimen, thin film solar cell, FIB Thin films of hydrogenated Si (Si:H) can be used as active absorber layers in solar cells deposited on low cost substrates using plasma-enhanced chemical vapour

  1. Dual gratings for enhanced light trapping in thin-film solar cells

    E-Print Network [OSTI]

    Dual gratings for enhanced light trapping in thin-film solar cells by a layer-transfer technique, Ireland * christian.schuster@york.ac.uk Abstract: Thin film solar cells benefit significantly from, "Progress and outlook for high-efficiency crystalline silicon solar cells," Sol. Energy Mater. Sol. Cells 65

  2. Plasticity contributions to interface adhesion in thin-film interconnect structures

    E-Print Network [OSTI]

    Vainchtein, Anna

    Plasticity contributions to interface adhesion in thin-film interconnect structures Michael Lanea of plasticity in thin copper layers on the interface fracture resistance in thin-film interconnect structures yield properties together with a plastic flow model for the metal layers were used to predict

  3. Optimization of the absorption efficiency of an amorphous-silicon thin-film tandem solar cell

    E-Print Network [OSTI]

    to bring down the cost of photovoltaic (PV) solar cells has gained huge momentum, and many strategiesOptimization of the absorption efficiency of an amorphous-silicon thin-film tandem solar cell-wave approach was used to compute the plane-wave absorptance of a thin-film tandem solar cell with a metallic

  4. Optimization and Characterization of RF Sputtered Piezoelectric Zinc Oxide Thin Film for

    E-Print Network [OSTI]

    Tang, William C

    Oxide (ZnO) thin films had been found to have unique piezoelectric effect for the applicationsOptimization and Characterization of RF Sputtered Piezoelectric Zinc Oxide Thin Film for Transducer Applications Yu-Hsiang Hsu, John Lin, and William C. Tang* Department of Biomedical Engineering University

  5. Thin-Film Active Nano-PWAS for Structural Health Monitoring , Victor Giurgiutiu1

    E-Print Network [OSTI]

    Giurgiutiu, Victor

    Thin-Film Active Nano-PWAS for Structural Health Monitoring Bin Lin1 , Victor Giurgiutiu1 , Amar S 3 University of Texas Arlington, Arlington, TX 76019 ABSTRACT Structural health monitoring (SHM is to develop the fabrication and optimum design of thin-film nano-PWAS for structural health monitoring

  6. THIN-FILM FLOWS WITH WALL SLIP: AN ASYMPTOTIC ANALYSIS OF HIGHER ORDER GLACIER FLOW MODELS

    E-Print Network [OSTI]

    Fournier, John J.F.

    THIN-FILM FLOWS WITH WALL SLIP: AN ASYMPTOTIC ANALYSIS OF HIGHER ORDER GLACIER FLOW MODELS, Cambridge, CB3 0ET, UK) [Received 6 January 2009. Revise 6 November 2009] Summary Free-surface thin film of the flow. Conversely, membrane or `free film' models are appropriate in situations where there is rapid

  7. Organic thin film devices with stabilized threshold voltage and mobility, and method for preparing the devices

    DOE Patents [OSTI]

    Nastasi, Michael Anthony; Wang, Yongqiang; Fraboni, Beatrice; Cosseddu, Piero; Bonfiglio, Annalisa

    2013-06-11

    Organic thin film devices that included an organic thin film subjected to a selected dose of a selected energy of ions exhibited a stabilized mobility (.mu.) and threshold voltage (VT), a decrease in contact resistance R.sub.C, and an extended operational lifetime that did not degrade after 2000 hours of operation in the air.

  8. Conductive polymer/fullerene blend thin films with honeycomb framework for transparent photovoltaic application

    DOE Patents [OSTI]

    Cotlet, Mircea; Wang, Hsing-Lin; Tsai, Hsinhan; Xu, Zhihua

    2015-04-21

    Optoelectronic devices and thin-film semiconductor compositions and methods for making same are disclosed. The methods provide for the synthesis of the disclosed composition. The thin-film semiconductor compositions disclosed herein have a unique configuration that exhibits efficient photo-induced charge transfer and high transparency to visible light.

  9. DISSERTATION ANALYSIS OF IMPACT OF NON-UNIFORMITIES ON THIN-FILM SOLAR CELLS

    E-Print Network [OSTI]

    Sites, James R.

    DISSERTATION ANALYSIS OF IMPACT OF NON-UNIFORMITIES ON THIN-FILM SOLAR CELLS AND MODULES WITH 2-D-FILM SOLAR CELLS AND MODULES WITH 2-D SIMULATIONS BE ACCEPTED AS FULFILLING IN PART REQUIREMENTS-UNIFORMITIES ON THIN-FILM SOLAR CELLS AND MODULES WITH 2-D SIMULATIONS Clean and environmentally friendly photovoltaic

  10. Configuration Optimization of a Nanosphere Array on Top of a Thin Film Solar Cell

    E-Print Network [OSTI]

    Grandidier, Jonathan

    Configuration Optimization of a Nanosphere Array on Top of a Thin Film Solar Cell J. Grandidier photocurrent of the solar cell. On a typical thin film amorphous silicon solar cell, a parametric analysis of SiO2 spheres directly placed on top of a-Si [1] and gallium arsenide (GaAs) [3] solar cells. We

  11. Computational analysis of thin film InGaAs/GaAs quantum well solar cells with

    E-Print Network [OSTI]

    Yu, Edward T.

    Computational analysis of thin film InGaAs/GaAs quantum well solar cells with back side light, Austin, TX 78758, USA * ety@ece.utexas.edu Abstract: Simulations of thin film (~2.5 µm thick) InGaAs/GaAs. Roberts, G. Hill, and C. Calder, "Progress in quantum well solar cells," Thin Solid Films 511­512, 76

  12. Semiconductor heterostructures and optimization of light-trapping structures for efficient thin-film solar cells

    E-Print Network [OSTI]

    Yu, Edward T.

    and optimization of light-trapping structures for efficient thin-film solar cells Claiborne O McPheeters1 , Dongzhi elements are integrated for light trapping. Measurements and simulations of GaAs solar cells with less than in their performance. Keywords: quantum-well, quantum-dot, scattering, diffraction, thin-film, GaAs, InAs, photovoltaic

  13. The peeling behavior of thin films with finite bending stiffness and the implications on gecko adhesion

    E-Print Network [OSTI]

    . This paper assesses the influence of the bending stiffness on thin film peeling and argues that detailedThe peeling behavior of thin films with finite bending stiffness and the implications on gecko the bending stiffness of the spatula has a strong influence on the peeling force which is neglected

  14. Bending tests of carbon nanotube thin-film transistors on flexible Daniel Pham1

    E-Print Network [OSTI]

    Chen, Ray

    Bending tests of carbon nanotube thin-film transistors on flexible substrate Daniel Pham1 , Harish, San Marcos, TX 78666. ABSTRACT Bending tests of carbon nanotube thin-film transistors on flexible substrate have been characterized in this paper. The device channel consisting of dense, aligned, 99% pure

  15. Mixed-mode interfacial adhesive strength of a thin film on an anisotropic substrate

    E-Print Network [OSTI]

    Sottos, Nancy R.

    Mixed-mode interfacial adhesive strength of a thin film on an anisotropic substrate Rajesh Kiteya adhesion strength between a gold (Au) thin film and an anisotropic passivated silicon (Si) substrate delamination remain a major reliability concern as interfacial properties, in particular interfacial adhesion

  16. Growth and characterization of aligned carbon nanotubes from patterned nickel nanodots and uniform thin films

    E-Print Network [OSTI]

    Reed, Mark

    Growth and characterization of aligned carbon nanotubes from patterned nickel nanodots and uniform nanotubes grown on patterned nickel nanodots and uniform thin films by plasma-enhanced chemical vapor on patterned nickel nanodots and uniform thin films is different. During growth of carbon nanotubes, a nickel

  17. Role of oxide thickening in fatigue crack initiation in LIGA nickel MEMS thin films

    E-Print Network [OSTI]

    Shan, Wanliang

    Role of oxide thickening in fatigue crack initiation in LIGA nickel MEMS thin films W.L. Shan a 2012 Accepted 16 October 2012 Available online 24 October 2012 Keywords: LIGA Ni MEMS thin films Oxide micro-electro-mechanical-systems (MEMS) structures. & 2012 Elsevier B.V. All rights reserved. 1

  18. Fracture toughness of polycrystalline silicon carbide thin films J. J. Bellante and H. Kahn

    E-Print Network [OSTI]

    Ballarini, Roberto

    Fracture toughness of polycrystalline silicon carbide thin films J. J. Bellante and H. Kahn online 11 February 2005 Thin film polycrystalline silicon carbide poly-SiC doubly clamped microtensile reported, including pressure sensors,2,3 bolometers,4 resonators,5,6 and fuel atomizers;7 these were

  19. Study of lithium diffusion in RF sputtered Nickel/Vanadium mixed oxides thin films

    E-Print Network [OSTI]

    Artuso, Florinda

    Study of lithium diffusion in RF sputtered NickelÁ/Vanadium mixed oxides thin films F. Artuso a lithium insertion inside RF sputtered Ni/V mixed oxides thin films have been investigated employing, showed three steps clearly involved in the intercalation mechanism of lithium in the oxide films: (i

  20. Thin-film Lithium Niobate Contour-mode Resonators Renyuan Wang and Sunil A. Bhave

    E-Print Network [OSTI]

    Afshari, Ehsan

    Thin-film Lithium Niobate Contour-mode Resonators Renyuan Wang and Sunil A. Bhave School Micro Devices, Inc. Greensboro, North Carolina, USA Abstract--This paper presents Lithium Niobate (LN this platform, we demonstrate, on a black Y136 cut Lithium Niobate thin-film, one-port high-order width

  1. Photonic light trapping and electrical transport in thin-film silicon solar cells

    E-Print Network [OSTI]

    Photonic light trapping and electrical transport in thin-film silicon solar cells Lucio Claudio Keywords: Thin-film solar cells Light trapping Photonic structures Carrier collection Electro-optical simulations Surface recombination a b s t r a c t Efficient solar cells require both strong absorption

  2. METAL BLACKS AS SCATTERING CENTERS TO INCREASE THE EFFICIENCY OF THIN FILM SOLAR CELLS

    E-Print Network [OSTI]

    Peale, Robert E.

    METAL BLACKS AS SCATTERING CENTERS TO INCREASE THE EFFICIENCY OF THIN FILM SOLAR CELLS by DEEP R surface of thin-film solar cells to improve efficiency. The principle is that scattering, which film solar cell. The particular types of particles investigated here are known as "metal-black", well

  3. Bill Shafarman 1 May 15, 2013 Thin Film Photovoltaics Research at the

    E-Print Network [OSTI]

    Firestone, Jeremy

    Bill Shafarman 1 May 15, 2013 Thin Film Photovoltaics Research at the Institute of Energy of Photovoltaics 2. IEC: History and Capabilities 3. Current Research at IEC #12;Bill Shafarman 2 May 15, 2013 Concentrators #12;Bill Shafarman 5 May 15, 2013 Thin Film Photovoltaics Potential for low cost PV using " a

  4. Study of the thin-film palladium/hydrogen system by an optical transmittance method

    E-Print Network [OSTI]

    Mandelis, Andreas

    Study of the thin-film palladium/hydrogen system by an optical transmittance method Jose A. Garcia, Canada Received 22 March 1996; accepted for publication 21 August 1996 The thin-film palladium/hydrogen Laboratory and Center for Hydrogen and Electrochemical Studies (CHES), University of Toronto, Toronto M5S 3G8

  5. Resonant cavity enhanced light harvesting in flexible thin-film organic solar cells

    E-Print Network [OSTI]

    Fan, Shanhui

    Resonant cavity enhanced light harvesting in flexible thin-film organic solar cells Nicholas P of solar energy conversion be- cause they use thin films of photoactive material and can be manufactured and photocurrent in flexible organic solar cells. We demonstrate that this enhancement is attributed to a broadband

  6. Molecular Dynamics Simulation of Thin Films with Rough and Asymmetric Interfaces

    E-Print Network [OSTI]

    Walker, D. Greg

    Molecular Dynamics Simulation of Thin Films with Rough and Asymmetric Interfaces N.A. Roberts with the use of interfaces and shows that pristine, imperfect and asymmetric interfaces in thin films can interface whose features are of the order of the phonon wavelength. At a constant temperature difference

  7. Investigation of Solar Energy Transfer through Plasmonic Au Nanoparticle-doped Sol-derived TiO? Thin Films in Photocatalysis and Photovoltaics /

    E-Print Network [OSTI]

    Zelinski, Andrew

    2013-01-01

    TiO 2 Thin Films in Photocatalysis and Photovoltaics ATiO 2 Thin Films in Photocatalysis and Photovoltaics by

  8. Low-cost solar flat-plate-collector development

    SciTech Connect (OSTI)

    Wilhelm, W.G.

    1981-01-01

    Cost goals were developed for the collector which led to the rejection of conventional approaches and to the exploration of thin-film technology. A thin-film sola absorber suited for high-speed continous-roll manufacture at low cost was designed. The absorber comprises two sheets of aluminum-foil/polymeric-material laminate bonded together at intervals to form channels with water as the heat transfer fluid. Several flat-plate panels were fabricated and tested. (MHR)

  9. Analytical model for the optical functions of amorphous semiconductors from the near-infrared to ultraviolet: Applications in thin film

    E-Print Network [OSTI]

    Deng, Xunming

    -infrared to ultraviolet: Applications in thin film photovoltaics A. S. Ferlauto, G. M. Ferreira, J. M. Pearce, C. R. Wronski, and R. W. Collinsa) Department of Physics, Materials Research Institute, and Center for Thin Film, it has numerous applications in the analysis and simulation of thin film a-Si:H based p-i-n and n

  10. High Efficiency Thin Film CdTe and a-Si Based Solar Cells Annual Technical Report for the Period

    E-Print Network [OSTI]

    Deng, Xunming

    High Efficiency Thin Film CdTe and a-Si Based Solar Cells Annual Technical Report for the Period This report covers the second year of this subcontract for research on high efficiency CdTe-based thin-film solar cells and on high efficiency a-Si-based thin-film solar cells. The effort on CdTe- based materials

  11. Universality of non-Ohmic shunt leakage in thin-film solar cells S. Dongaonkar,1,a

    E-Print Network [OSTI]

    Alam, Muhammad A.

    Universality of non-Ohmic shunt leakage in thin-film solar cells S. Dongaonkar,1,a J. D. Servaites thin-film solar cell types: hydrogenated amorphous silicon a-Si:H p-i-n cells, organic bulk understanding of thin film solar cell device physics, including important module performance variability issues

  12. Improved red-response in thin film a-Si:H solar cells with soft-imprinted plasmonic back reflectors

    E-Print Network [OSTI]

    Polman, Albert

    Improved red-response in thin film a-Si:H solar cells with soft-imprinted plasmonic back reflectors is a critical component of solar cell development. In typical thin film cells the thickness of the absorbing of photovoltaic power. Thin film Si solar cells using hydrogenated amorphous Si a-Si:H and nano- crystalline Si nc

  13. Mode coupling by plasmonic surface scatterers in thin-film silicon solar cells M. van Lare,1

    E-Print Network [OSTI]

    Polman, Albert

    Mode coupling by plasmonic surface scatterers in thin-film silicon solar cells M. van Lare,1 F a completed thin-film a-Si:H solar cell. Current-voltage measurements show a photocurrent enhancement of 10 of Physics. [http://dx.doi.org/10.1063/1.4767997] Thin-film solar cells offer the potential of high photovol

  14. EFFECT OF HYDROGEN ON SURFACE TEXTURING AND CRYSTALLIZATION ON A-SI:H THIN FILM IRRADIATED BY EXCIMER LASER

    E-Print Network [OSTI]

    Yao, Y. Lawrence

    -Si:H thin film solar cell applications. Introduction Many industrial solar cells in use today use bulk and instability, thin-film a- Si:H solar cells require a highly efficient light-trapping design to absorb cell applications. In this study, hydrogenated and dehydrogenated amorphous silicon thin films

  15. Studies of thin film hydrogenated silicon solar cells using electron energy-loss spectroscopy in the transmission electron microscope

    E-Print Network [OSTI]

    Dunin-Borkowski, Rafal E.

    Studies of thin film hydrogenated silicon solar cells using electron energy-loss spectroscopy (TEM) to study n-i-p thin film Si solar cells grown on steel foil or glass substrates. For a solar cell experiment, we study the chemical compositions of defective regions in thin film Si solar cells using energy

  16. CRYSTALLINE SILICON THIN-FILM SOLAR CELLS FROM THE POROUS SILICON PROCESS APPLYING CONVECTION ASSISTED CHEMICAL VAPOR DEPOSITION

    E-Print Network [OSTI]

    CRYSTALLINE SILICON THIN-FILM SOLAR CELLS FROM THE POROUS SILICON PROCESS APPLYING CONVECTION for the first time to monocrystalline Si thin-film solar cells from the porous silicon (PSI) layer transfer for manufacturing high efficiency silicon thin-film solar cells. Industrially feasible epitaxy systems therefore

  17. Transparent electrode requirements for thin film solar cell modules Michael W. Rowell and Michael D. McGehee*

    E-Print Network [OSTI]

    McGehee, Michael

    Transparent electrode requirements for thin film solar cell modules Michael W. Rowell and Michael D The transparent conductor (TC) layer in thin film solar cell modules has a significant impact on the power to replace conducting oxides in this geometry. Thin film solar cell modules can be manufactured either

  18. Enhancement of optical absorption in thin-film organic solar cells through the excitation of plasmonic modes in metallic gratings

    E-Print Network [OSTI]

    Fan, Shanhui

    Enhancement of optical absorption in thin-film organic solar cells through the excitation.1063/1.3377791 Thin-film organic solar cells OSCs are a promising candidate for low-cost energy conversion.1­6 However 2010 We theoretically investigate the enhancement of optical absorption in thin-film organic solar

  19. Electrodeposition of Zn based nanostructure thin films for photovoltaic applications

    SciTech Connect (OSTI)

    Al-Bat’hi, S. A. M.

    2015-03-30

    We present here a systematic study on the synthesis thin films of various ZnO, CdO, Zn{sub x}Cd{sub 1-x} (O) and ZnTe nanostructures by electrodeposition technique with ZnCl{sub 2,} CdCl{sub 2} and ZnSO{sub 4} solution as starting reactant. Several reaction parameters were examined to develop an optimal procedure for controlling the size, shape, and surface morphology of the nanostructure. The results showed that the morphology of the products can be carefully controlled through adjusting the concentration of the electrolyte. The products present well shaped Nanorods arrays at specific concentration and temperature. UV-VIS spectroscopy and X-ray diffraction results show that the product presents good crystallinity. A possible formation process has been proposed.

  20. Optical limiting effects in nanostructured silicon carbide thin films

    SciTech Connect (OSTI)

    Borshch, A A; Starkov, V N; Volkov, V I; Rudenko, V I; Boyarchuk, A Yu; Semenov, A V

    2013-12-31

    We present the results of experiments on the interaction of nanosecond laser radiation at 532 and 1064 nm with nanostructured silicon carbide thin films of different polytypes. We have found the effect of optical intensity limiting at both wavelengths. The intensity of optical limiting at ? = 532 nm (I{sub cl} ? 10{sup 6} W cm{sup -2}) is shown to be an order of magnitude less than that at ? = 1064 nm (I{sub cl} ? 10{sup 7} W cm{sup -2}). We discuss the nature of the nonlinearity, leading to the optical limiting effect. We have proposed a method for determining the amount of linear and two-photon absorption in material media. (nonlinear optical phenomena)

  1. The electron beam hole drilling of silicon nitride thin films

    SciTech Connect (OSTI)

    Howitt, D. G.; Chen, S. J.; Gierhart, B. C.; Smith, R. L.; Collins, S. D.

    2008-01-15

    The mechanism by which an intense electron beam can produce holes in thin films of silicon nitride has been investigated using a combination of in situ electron energy loss spectrometry and electron microscopy imaging. A brief review of electron beam interactions that lead to material loss in different materials is also presented. The loss of nitrogen and silicon decreases with decreasing beam energy and although still observable at a beam energy of 150 keV ceases completely at 120 keV. The linear behavior of the loss rate coupled with the energy dependency indicates that the process is primarily one of direct displacement, involving the sputtering of atoms from the back surface of the specimen with the rate controlling mechanism being the loss of nitrogen.

  2. MultiLayer solid electrolyte for lithium thin film batteries

    DOE Patents [OSTI]

    Lee, Se -Hee; Tracy, C. Edwin; Pitts, John Roland; Liu, Ping

    2015-07-28

    A lithium metal thin-film battery composite structure is provided that includes a combination of a thin, stable, solid electrolyte layer [18] such as Lipon, designed in use to be in contact with a lithium metal anode layer; and a rapid-deposit solid electrolyte layer [16] such as LiAlF.sub.4 in contact with the thin, stable, solid electrolyte layer [18]. Batteries made up of or containing these structures are more efficient to produce than other lithium metal batteries that use only a single solid electrolyte. They are also more resistant to stress and strain than batteries made using layers of only the stable, solid electrolyte materials. Furthermore, lithium anode batteries as disclosed herein are useful as rechargeable batteries.

  3. Thermoelectric effect in very thin film Pt/Au thermocouples

    SciTech Connect (OSTI)

    Salvadori, M.C.; Vaz, A.R.; Teixeira, F.S.; Cattani, M.; Brown,I.G.

    2006-01-10

    The thickness dependence of the thermoelectric power of Pt films of variable thickness on a reference Au film has been determined for the case when the Pt film thickness, t, is not large compared to the charge carrier mean free path, {ell}, that is, t/{ell}. Pt film thicknesses down to 2.2 nm were investigated. We find that {Delta}S{sub F} = S{sub B}-S{sub F} (where S{sub B} and S{sub F} are the thermopowers of the Pt bulk and film, respectively) does not vary linearly as 1/t as is the case for thin film thermocouples when the film thickness is large compared to the charge carrier mean free path.

  4. Origin of superstructures in (double) perovskite thin films

    SciTech Connect (OSTI)

    Shabadi, V. Major, M.; Komissinskiy, P.; Vafaee, M.; Radetinac, A.; Baghaie Yazdi, M.; Donner, W.; Alff, L.

    2014-09-21

    We have investigated the origin of superstructure peaks as observed by X-ray diffraction of multiferroic Bi(Fe{sub 0.5}Cr{sub 0.5})O{sub 3} thin films grown by pulsed laser deposition on single crystal SrTiO{sub 3} substrates. The photon energy dependence of the contrast between the atomic scattering factors of Fe and Cr is used to rule out a chemically ordered double perovskite Bi{sub 2}FeCrO{sub 6} (BFCO). Structural calculations suggest that the experimentally observed superstructure occurs due to unequal cation displacements along the pseudo-cubic [111] direction that mimic the unit cell of the chemically ordered compound. This result helps to clarify discrepancies in the correlations of structural and magnetic order reported for Bi{sub 2}FeCrO{sub 6}. The observation of a superstructure in itself is not a sufficient proof of chemical order in double perovskites.

  5. Characterization on RF magnetron sputtered niobium pentoxide thin films

    SciTech Connect (OSTI)

    Usha, N. [Department of Physics, Alagappa University, Karaikudi - 630 004 (India); Sivakumar, R., E-mail: krsivakumar1979@yahoo.com [Directorate of Distance Education, Alagappa University, Karaikudi - 630 004 (India); Sanjeeviraja, C. [Department of Physics, Alagappa Chettiar College of Engineering and Technology, Karaikudi - 630 004 (India)

    2014-10-15

    Niobium pentoxide (Nb{sub 2}O{sub 5}) thin films with amorphous nature were deposited on microscopic glass substrates at 100°C by rf magnetron sputtering technique. The effect of rf power on the structural, morphological, optical, and vibrational properties of Nb{sub 2}O{sub 5} films have been investigated. Optical study shows the maximum average transmittance of about 87% and the optical energy band gap (indirect allowed) changes between 3.70 eV and 3.47 eV. AFM result indicates the smooth surface nature of the samples. Photoluminescence measurement showed the better optical quality of the deposited films. Raman spectra show the LO-TO splitting of Nb-O stretching of Nb{sub 2}O{sub 5} films.

  6. Studies on nickel-tungsten oxide thin films

    SciTech Connect (OSTI)

    Usha, K. S. [Department of Physics, Alagappa University, Karaikudi - 630 004 (India); Sivakumar, R., E-mail: krsivakumar1979@yahoo.com [Directorate of Distance Education, Alagappa University, Karaikudi - 630 004 (India); Sanjeeviraja, C. [Department of Physics, Alagappa Chettiar College of Engineering and Technology, Karaikudi - 630 004 (India)

    2014-10-15

    Nickel-Tungsten oxide (95:5) thin films were prepared by rf sputtering at 200W rf power with various substrate temperatures. X-ray diffraction study reveals the amorphous nature of films. The substrate temperature induced decrease in energy band gap with a maximum transmittance of 71%1 was observed. The Micro-Raman study shows broad peaks at 560 cm{sup ?1} and 1100 cm{sup ?1} correspond to Ni-O vibration and the peak at 860 cm{sup ?1} can be assigned to the vibration of W-O-W bond. Photoluminescence spectra show two peaks centered on 420 nm and 485 nm corresponding to the band edge emission and vacancies created due to the addition of tungsten, respectively.

  7. Method for making thick and/or thin film

    DOE Patents [OSTI]

    Pham, Ai Quoc; Glass, Robert S.

    2004-11-02

    A method to make thick or thin films a very low cost. The method is generally similar to the conventional tape casting techniques while being more flexible and versatile. The invention involves preparing a slip (solution) of desired material and including solvents such as ethanol and an appropriate dispersant to prevent agglomeration. The slip is then sprayed on a substrate to be coated using an atomizer which spreads the slip in a fine mist. Upon hitting the substrate, the solvent evaporates, leaving a green tape containing the powder and other additives, whereafter the tape may be punctured, cut, and heated for the desired application. The tape thickness can vary from about 1 .mu.m upward.

  8. Long-laser-pulse method of producing thin films

    DOE Patents [OSTI]

    Balooch, Mehdi (Berkeley, CA); Olander, Donald K. (Berkeley, CA); Russo, Richard E. (Walnut Creek, CA)

    1991-01-01

    A method of depositing thin films by means of laser vaporization employs a long-pulse laser (Nd-glass of about one millisecond duration) with a peak power density typically in the range 10.sup.5 -10.sup.6 W/cm.sup.2. The method may be used to produce high T.sub.c superconducting films of perovskite material. In one embodiment, a few hundred nanometers thick film of YBa.sub.2 Cu.sub.3 O.sub.7-x is produced on a SrTiO.sub.3 crystal substrate in one or two pulses. In situ-recrystallization and post-annealing, both at elevated temperature and in the presence of an oxidizing agen The invention described herein arose in the course of, or under, Contract No. DE-C03-76SF0098 between the United States Department of Energy and the University of California.

  9. Equiatomic CoPt thin films with extremely high coercivity

    SciTech Connect (OSTI)

    Varghese, Binni; Piramanayagam, S. N. Yang, Yi; Kai Wong, Seng; Khume Tan, Hang; Kiat Lee, Wee; Okamoto, Iwao

    2014-05-07

    In this paper, magnetic and structural properties of near-equiatomic CoPt thin films, which exhibited a high coercivity in the film-normal direction—suitable for perpendicular magnetic recording media applications—are reported. The films exhibited a larger coercivity of about 6.5 kOe at 8?nm. The coercivity showed a monotonous decrease as the film thickness was increased. The transmission electron microscopy images indicated that the as fabricated CoPt film generally consists of a stack of magnetically hard hexagonal-close-packed phase, followed by stacking faults and face-centred-cubic phase. The thickness dependent magnetic properties are explained on the basis of exchange-coupled composite media. Epitaxial growth on Ru layers is a possible factor leading to the unusual observation of magnetically hard hcp-phase at high concentrations of Pt.

  10. Room-temperature magnetoelectric multiferroic thin films and applications thereof

    DOE Patents [OSTI]

    Katiyar, Ram S; Kuman, Ashok; Scott, James F.

    2014-08-12

    The invention provides a novel class of room-temperature, single-phase, magnetoelectric multiferroic (PbFe.sub.0.67W.sub.0.33O.sub.3).sub.x (PbZr.sub.0.53Ti.sub.0.47O.sub.3).sub.1-x (0.2.ltoreq.x.ltoreq.0.8) (PFW.sub.x-PZT.sub.1-x) thin films that exhibit high dielectric constants, high polarization, weak saturation magnetization, broad dielectric temperature peak, high-frequency dispersion, low dielectric loss and low leakage current. These properties render them to be suitable candidates for room-temperature multiferroic devices. Methods of preparation are also provided.

  11. Naphthacene Based Organic Thin Film Transistor With Rare Earth Oxide

    SciTech Connect (OSTI)

    Konwar, K. [Department of Physics, Digboi College, Digboi-786171, Assam (India); Baishya, B. [Department of Physics, Dibrugarh University, Dibrugarh-786004, Assam (India)

    2010-12-01

    Naphthacene based organic thin film transistors (OTFTs) have been fabricated using La{sub 2}O{sub 3}, as the gate insulator. All the OTFTs have been fabricated by the process of thermal evaporation in vacuum on perfectly cleaned glass substrates with aluminium as source-drain and gate electrodes. The naphthacene film morphology on the glass substrate has been studied by XRD and found to be polycrystalline in nature. The field effect mobility, output resistance, amplification factor, transconductance and gain bandwidth product of the OTFTs have been calculated by using theoretical TFT model. The highest value of field effect mobility is found to be 0.07x10{sup -3} cm{sup 2}V{sup -1}s{sup -1} for the devices annealed in vacuum at 90 deg. C for 5 hours.

  12. Microstructure of amorphous indium oxide and tin oxide thin films

    SciTech Connect (OSTI)

    Rauf, I.A.; Brown, L.M. (Univ. of Cambridge (United Kingdom))

    1994-03-15

    Indium oxide, tin oxide, and some other doped and undoped oxide semiconductors show an interesting and technologically important combination of properties. They have high luminous transparency, good electrical conductivity and high infrared reflectivity. Numerous techniques for depositing these materials have been developed and have undergone a number of changes during last two decades. An understanding of the basic physics of these materials has begun to dawn. Most of the literature on transparent conducting oxides consists of studying the dependence of the properties on the composition, preparation conditions, such as deposition rate, substrate temperature or post-deposition heat treatment. In this paper the authors have employed the transmission electron microscopy to study the microstructure of reactively evaporated, electron beam evaporated, ion-beam sputtered amorphous indium oxide and reactively evaporated amorphous tin oxide thin films. These films, which have received little attention in the past, can have enormous potential as transparent conductive coatings on heat-sensitive substrates and inexpensive solar cells.

  13. Ultra-high current density thin-film Si diode

    DOE Patents [OSTI]

    Wang; Qi (Littleton, CO)

    2008-04-22

    A combination of a thin-film .mu.c-Si and a-Si:H containing diode structure characterized by an ultra-high current density that exceeds 1000 A/cm.sup.2, comprising: a substrate; a bottom metal layer disposed on the substrate; an n-layer of .mu.c-Si deposited the bottom metal layer; an i-layer of .mu.c-Si deposited on the n-layer; a buffer layer of a-Si:H deposited on the i-layer, a p-layer of .mu.c-Si deposited on the buffer layer; and a top metal layer deposited on the p-layer.

  14. Photoconductivity in reactively evaporated copper indium selenide thin films

    SciTech Connect (OSTI)

    Urmila, K. S., E-mail: urmilaks7@gmail.com; Asokan, T. Namitha, E-mail: urmilaks7@gmail.com; Pradeep, B., E-mail: urmilaks7@gmail.com [Solid State Physics Laboratory, Cochin University of Science and Technology, Kochi, Kerala (India); Jacob, Rajani; Philip, Rachel Reena [Thin Film Research Laboratory, Union Christian College, Aluva, Kerala (India)

    2014-01-28

    Copper indium selenide thin films of composition CuInSe{sub 2} with thickness of the order of 130 nm are deposited on glass substrate at a temperature of 423 ±5 K and pressure of 10{sup ?5} mbar using reactive evaporation, a variant of Gunther's three temperature method with high purity Copper (99.999%), Indium (99.999%) and Selenium (99.99%) as the elemental starting materials. X-ray diffraction (XRD) studies shows that the films are polycrystalline in nature having preferred orientation of grains along the (112) plane. The structural type of the film is found to be tetragonal with particle size of the order of 32 nm. The structural parameters such as lattice constant, particle size, dislocation density, number of crystallites per unit area and strain in the film are also evaluated. The surface morphology of CuInSe{sub 2} films are studied using 2D and 3D atomic force microscopy to estimate the grain size and surface roughness respectively. Analysis of the absorption spectrum of the film recorded using UV-Vis-NIR Spectrophotometer in the wavelength range from 2500 nm to cutoff revealed that the film possess a direct allowed transition with a band gap of 1.05 eV and a high value of absorption coefficient (?) of 10{sup 6} cm{sup ?1} at 570 nm. Photoconductivity at room temperature is measured after illuminating the film with an FSH lamp (82 V, 300 W). Optical absorption studies in conjunction with the good photoconductivity of the prepared p-type CuInSe{sub 2} thin films indicate its suitability in photovoltaic applications.

  15. Fundamentals of polycrystalline thin film materials and devices

    SciTech Connect (OSTI)

    Baron, B.N.; Birkmire, R.W.; Phillips, J.E.; Shafarman, W.N.; Hegedus, S.S.; McCandless, B.E. (Delaware Univ., Newark, DE (USA). Inst. of Energy Conversion)

    1991-01-01

    This report presents the results of a one-year research program on polycrystalline thin-film solar cells. The research was conducted to better understand the limitations and potential of solar cells using CuInSe{sub 2} and CdTe by systematically investigating the fundamental relationships linking material processing, material properties, and device behavior. By selenizing Cu and In layers, we fabricated device-quality CuInSe{sub 2} thin films and demonstrated a CuInSe{sub 2} solar cell with 7% efficiency. We added Ga, to increase the band gap of CuInSe{sub 2} devices to increase the open-circuit voltage to 0.55 V. We fabricated and analyzed Cu(InGa)Se{sub 2}/CuInSe{sub 2} devices to demonstrate the potential for combining the benefits of higher V{sub oc} while retaining the current-generating capacity of CuInSe{sub 2}. We fabricated an innovative superstrate device design with more than 5% efficiency, as well as a bifacial spectral-response technique for determining the electron diffusion length and optical absorption coefficient of CuInSe{sub 2} in an operational cell. The diffusion length was found to be greater than 1 {mu}m. We qualitatively modeled the effect of reducing heat treatments in hydrogen and oxidizing treatments in air on the I-V behavior of CuInSe{sub 2} devices. We also investigated post-deposition heat treatments and chemical processing and used them to fabricate a 9.6%-efficient CdTe/CdS solar cell using physical vapor deposition.

  16. Amorphous semiconducting and conducting transparent metal oxide thin films and production thereof

    DOE Patents [OSTI]

    Perkins, John (Boulder, CO); Van Hest, Marinus Franciscus Antonius Maria (Lakewood, CO); Ginley, David (Evergreen, CO); Taylor, Matthew (Golden, CO); Neuman, George A. (Holland, MI); Luten, Henry A. (Holland, MI); Forgette, Jeffrey A. (Hudsonville, MI); Anderson, John S. (Holland, MI)

    2010-07-13

    Metal oxide thin films and production thereof are disclosed. An exemplary method of producing a metal oxide thin film may comprise introducing at least two metallic elements and oxygen into a process chamber to form a metal oxide. The method may also comprise depositing the metal oxide on a substrate in the process chamber. The method may also comprise simultaneously controlling a ratio of the at least two metallic elements and a stoichiometry of the oxygen during deposition. Exemplary amorphous metal oxide thin films produced according to the methods herein may exhibit highly transparent properties, highly conductive properties, and/or other opto-electronic properties.

  17. Silicon-integrated thin-film structure for electro-optic applications

    DOE Patents [OSTI]

    McKee, Rodney A. (Kingston, TN); Walker, Frederick Joseph (Oak Ridge, TN)

    2000-01-01

    A crystalline thin-film structure suited for use in any of an number of electro-optic applications, such as a phase modulator or a component of an interferometer, includes a semiconductor substrate of silicon and a ferroelectric, optically-clear thin film of the perovskite BaTiO.sub.3 overlying the surface of the silicon substrate. The BaTiO.sub.3 thin film is characterized in that substantially all of the dipole moments associated with the ferroelectric film are arranged substantially parallel to the surface of the substrate to enhance the electro-optic qualities of the film.

  18. High-field magnets using high-critical-temperature superconducting thin films

    DOE Patents [OSTI]

    Mitlitsky, F.; Hoard, R.W.

    1994-05-10

    High-field magnets fabricated from high-critical-temperature superconducting ceramic (HTSC) thin films which can generate fields greater than 4 Tesla are disclosed. The high-field magnets are made of stackable disk-shaped substrates coated with HTSC thin films, and involves maximizing the critical current density, superconducting film thickness, number of superconducting layers per substrate, substrate diameter, and number of substrates while minimizing substrate thickness. The HTSC thin films are deposited on one or both sides of the substrates in a spiral configuration with variable line widths to increase the field. 4 figures.

  19. High-field magnets using high-critical-temperature superconducting thin films

    DOE Patents [OSTI]

    Mitlitsky, Fred (Livermore, CA); Hoard, Ronald W. (Livermore, CA)

    1994-01-01

    High-field magnets fabricated from high-critical-temperature superconducting ceramic (HTSC) thin films which can generate fields greater than 4 Tesla. The high-field magnets are made of stackable disk-shaped substrates coated with HTSC thin films, and involves maximizing the critical current density, superconducting film thickness, number of superconducting layers per substrate, substrate diameter, and number of substrates while minimizing substrate thickness. The HTSC thin films are deposited on one or both sides of the substrates in a spiral configuration with variable line widths to increase the field.

  20. TRANSMISSION ELECTRON MICROSCOPY OF THE TEXTURED SILVER BACK REFLECTOR OF A THIN FILM SILICON SOLAR CELL: FROM CRYSTALLOGRAPHY TO OPTICAL ABSORPTION

    E-Print Network [OSTI]

    Dunin-Borkowski, Rafal E.

    in amorphous, microcrystalline and micromorph thin-film Si solar cells is an important and active field-reflector of thin-film Si solar cells. 1 INTRODUCTION The study of light trapping in thin-film Si solar cells for an optimized back reflector structure in a microcrystalline thin film Si solar cell, when compared with the use

  1. Photoluminescence-based quality control for thin film absorber layers of photovoltaic devices

    DOE Patents [OSTI]

    Repins, Ingrid L.; Kuciauskas, Darius

    2015-07-07

    A time-resolved photoluminescence-based system providing quality control during manufacture of thin film absorber layers for photovoltaic devices. The system includes a laser generating excitation beams and an optical fiber with an end used both for directing each excitation beam onto a thin film absorber layer and for collecting photoluminescence from the absorber layer. The system includes a processor determining a quality control parameter such as minority carrier lifetime of the thin film absorber layer based on the collected photoluminescence. In some implementations, the laser is a low power, pulsed diode laser having photon energy at least great enough to excite electron hole pairs in the thin film absorber layer. The scattered light may be filterable from the collected photoluminescence, and the system may include a dichroic beam splitter and a filter that transmit the photoluminescence and remove scattered laser light prior to delivery to a photodetector and a digital oscilloscope.

  2. Interaction of stress and magnetic properties in patterned copper-nickel-copper thin films

    E-Print Network [OSTI]

    Friend, Elizabeth, Ph. D. Massachusetts Institute of Technology

    2007-01-01

    In recent years, the epitaxial Cu/Ni/Cu thin film system has been extensively studied, due to its wide range of perpendicular magnetization. It has proved to be a model system to explore the interactions of strain, surface ...

  3. Antimicrobial Activity of Cationic Antiseptics in Layer-by-Layer Thin Film Assemblies 

    E-Print Network [OSTI]

    Dvoracek, Charlene M.

    2010-07-14

    Layer-by-layer (LbL) assembly has proven to be a powerful technique for assembling thin films with a variety of properties including electrochromic, molecular sensing, oxygen barrier, and antimicrobial. LbL involves the deposition of alternating...

  4. Nanocrystallization of LiCoO2 Cathodes for Thin Film Batteries Utilizing Pulse Thermal Processing

    SciTech Connect (OSTI)

    2009-04-01

    This factsheet describes a study whose focus is on the nanocrystallization of the LiCoO2 cathode thin films on polyimide substrates and evaluate the microstructural evolution and resistance as a function of PTP processing conditions.

  5. Evaluation on the thin-film phase change material-based technologies

    E-Print Network [OSTI]

    Guo, Qiang, M. Eng. Massachusetts Institute of Technology

    2006-01-01

    Two potential applications of thin film phase-change materials are considered, non-volatile electronic memories and MEMS (Micro-Electro-Mechanical Systems) actuators. The markets for those two applications are fast growing ...

  6. Thin Film Solar Cells with Light Trapping Transparent Conducting Oxide Layer 

    E-Print Network [OSTI]

    Lu, Tianlin

    2012-07-16

    Thin film solar cells, if film thickness is thinner than the optical absorption length, typically give lower cell performance. For the thinner structure, electric current loss due to light penetration can offset the electric ...

  7. Integration of pentacene-based thin film transistors via photolithography for low and high voltage applications

    E-Print Network [OSTI]

    Smith, Melissa Alyson

    2012-01-01

    An organic thin film transistor (OTFT) technology platform has been developed for flexible integrated circuits applications. OTFT performance is tuned by engineering the dielectric constant of the gate insulator and the ...

  8. Superconducting thin films of (100) and (111) oriented indium doped topological crystalline insulator SnTe

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Si, W.; Zhang, C.; Wu, L.; Ozaki, T.; Gu, G.; Li, Q.

    2015-09-01

    Recent discovery of the topological crystalline insulator SnTe has triggered a search for topological superconductors, which have potential application to topological quantum computing. The present work reports on the superconducting properties of indium doped SnTe thin films. The (100) and (111) oriented thin films were epitaxially grown by pulsed-laser deposition on (100) and (111) BaF2 crystalline substrates respectively. The onset superconducting transition temperatures are about 3.8 K for (100) and 3.6 K for (111) orientations, slightly lower than that of the bulk. Magneto-resistive measurements indicate that these thin films may have upper critical fields higher than that of the bulk.more »With large surface-to-bulk ratio, superconducting indium doped SnTe thin films provide a rich platform for the study of topological superconductivity and potential device applications based on topological superconductors.« less

  9. Characterization of the viscoelastic properties of thin-film materials using dynamic-mechanical testing techniques 

    E-Print Network [OSTI]

    Biskup, Bruce Allen

    1994-01-01

    An investigation into the use of dynamic mechanical analysis to characterize the viscoelastic properties of thin film materials is presented. The methodology was investigated using polyethylene films used on high altitude research balloons. Time...

  10. Optimization-based design of surface textures for thin-film Si solar cells

    E-Print Network [OSTI]

    Sheng, Xing

    We numerically investigate the light-absorption behavior of thin-film silicon for normal-incident light, using surface textures to enhance absorption. We consider a variety of texture designs, such as simple periodic ...

  11. Engineering broadband and anisotropic photoluminescence emission from rare earth doped tellurite thin film photonic crystals

    E-Print Network [OSTI]

    Vanhoutte, Michiel

    Broadband and anisotropic light emission from rare-earth doped tellurite thin films is demonstrated using Er[superscript 3+]-TeO[subscript 2] photonic crystals (PhCs). By adjusting the PhC parameters, photoluminescent light ...

  12. Thin film lithium-based batteries and electrochromic devices fabricated with nanocomposite electrode materials

    DOE Patents [OSTI]

    Gillaspie, Dane T; Lee, Se-Hee; Tracy, C. Edwin; Pitts, John Roland

    2014-02-04

    Thin-film lithium-based batteries and electrochromic devices (10) are fabricated with positive electrodes (12) comprising a nanocomposite material composed of lithiated metal oxide nanoparticles (40) dispersed in a matrix composed of lithium tungsten oxide.

  13. Title of Document: MULTIPLEXED CHEMICAL SENSING AND THIN FILM METROLOGY IN

    E-Print Network [OSTI]

    Anlage, Steven

    ABSTRACT Title of Document: MULTIPLEXED CHEMICAL SENSING AND THIN FILM METROLOGY IN PROGRAMMABLE proven valuable in understanding and controlling chemical processes used in semiconductor fabrication. Given the complexity of spatial distributions of fluid flow, thermal, and chemical parameters

  14. Near-infrared photodetector consisting of J-aggregating cyanine dye and metal oxide thin films

    E-Print Network [OSTI]

    Osedach, Timothy P.

    We demonstrate a near-infrared photodetector that consists of a thin film of the J-aggregating cyanine dye, U3, and transparent metal-oxide charge transport layers. The high absorption coefficient of the U3 film, combined ...

  15. The bias-stress effect in pentacene organic thin-film transistors

    E-Print Network [OSTI]

    Ryu, Kyungbum

    2010-01-01

    Organic thin-film transistors (OTFTs) are promising for flexible large-area electronics. However, the bias-stress effect (BSE) in OTFTs causes operational instability that limits the usefulness of the OTFT technology in a ...

  16. Light trapping and electrical transport in thin-film solar cells with randomly rough textures

    E-Print Network [OSTI]

    Yet, the central problem of thin-film photovoltaics is to capture and absorb sunlight in a thin active for photovoltaic applica- tions as intrinsically broadband scatterers. In this work, we use rigorous electro

  17. Magneto-optical and multiferroic oxide thin films, integrated nonreciprocal photonic devices and multiferroic memory devices

    E-Print Network [OSTI]

    Onbas??l?, Mehmet Cengiz

    2015-01-01

    Complex oxide thin films offer unique functionalities which can potentially extend the utility of current storage, processing and optical isolator technologies. In this thesis, we present three categories of studies on ...

  18. Water, salt water and alkaline solution uptake in epoxy thin films

    E-Print Network [OSTI]

    Scott, P.; Lees, Janet M.

    2013-05-10

    type and temperature, are explored. Experimental results, where the solution uptake in desiccated (D) or undesiccated (U) thin films of a commercially available epoxy matrix subjected to water (W), salt water (SW), or alkali concrete pore solution (CPS...

  19. Femtosecond pump-probe studies of reduced graphene oxide thin films

    E-Print Network [OSTI]

    Ruzicka, Brian Andrew; Werake, Lalani Kumari; Zhao, Hui; Wang, Shuai; Loh, Kian Ping

    2010-04-01

    The dynamics of photocarriers in reduced graphene oxide thin films is studied by using ultrafast pump-probe spectroscopy. Time dependent differential transmissions are measured with sample temperatures ranging from 9 to 300 K. At each sample...

  20. Sponsored by Nanotechnology Seminar Program Electronics on Anything: How Thin Film

    E-Print Network [OSTI]

    Fisher, Frank

    including electronically active and flexible materials. Our group has been working on the hybrid integrationSponsored by Nanotechnology Seminar Program Electronics on Anything: How Thin Film Electronics University ABSTRACT: Silicon electronics have revolutionized the processing and handling of information

  1. Micro/nano devices fabricated from Cu-Hf thin films

    DOE Patents [OSTI]

    Luber, Erik J; Ophus, Colin; Mitlin, David; Olsen, Brian; Harrower, Christopher; Radmilovi, Velimir

    2013-06-04

    An all-metal microdevice or nanodevice such as an atomic force microscope probe is manufactured from a copper-hafnium alloy thin film having an x-ray amorphous microstructure.

  2. Nonequilibrium superconducting thin films with sub-gap and pair-breaking photon illumination

    E-Print Network [OSTI]

    Guruswamy, T.; Goldie, D. J.; Withington, S.

    2015-04-08

    We calculate nonequilibrium quasiparticle and phonon distributions for a number of widely-used low transition temperature thin-film superconductors under constant, uniform illumination by sub-gap probe and pair-breaking signal photons simultaneously...

  3. Mechanisms of Zinc Oxide Nanocrystalline Thin Film Formation by Thermal Degradation of Metal-Loaded Hydrogels

    E-Print Network [OSTI]

    electrode in flat- panel displays,1 solar cells, and thin-film transistors.2,3 Other recent reports account as a short-range probe to investigate the first stages of nucleation and the following development of Zn

  4. Layer-by-Layer Assembly of a pH-Responsive and Electrochromic Thin Film

    E-Print Network [OSTI]

    Schmidt, Daniel J.

    This article summarizes an experiment on thin-film fabrication with layer-by-layer assembly that is appropriate for undergraduate laboratory courses. The purpose of this experiment is to teach students about self-assembly ...

  5. Preparation of W-Ta thin-film thermocouple on diamond anvil cell...

    Office of Scientific and Technical Information (OSTI)

    Preparation of W-Ta thin-film thermocouple on diamond anvil cell for in-situ temperature measurement under high pressure Citation Details In-Document Search Title: Preparation of...

  6. Experimental modeling of intergranular exchange coupling for perpendicular thin film media

    E-Print Network [OSTI]

    Laughlin, David E.

    does exist in the CoCrPt-oxide layer of present perpendicular thin film media, especially for media to quantitatively determine the ferromagnetic ex- change coupling through an oxide layer as a function of ox- ide

  7. Analysis of potential applications for the templated dewetting of metal thin films

    E-Print Network [OSTI]

    Frantzeskakis, Emmanouil

    2005-01-01

    Thin films have a high surface-to-volume ratio and are therefore usually morphologically unstable. They tend to reduce their surface energy through transport of mass by diffusion. As a result, they decay into a collection ...

  8. Earth abundant materials for high efficiency heterojunction thin film solar cells

    E-Print Network [OSTI]

    Buonassisi, Tonio

    We investigate earth abundant materials for thin-film solar cells that can meet tens of terawatts level deployment potential. Candidate materials are identified by combinatorial search, large-scale electronic structure ...

  9. Integrated photonic structures for light trapping in thin-film Si solar cells

    E-Print Network [OSTI]

    Sheng, Xing

    We explore the mechanisms for an efficient light trapping structure for thin-film silicon solar cells. The design combines a distributed Bragg reflector (DBR) and periodic gratings. Using photonic band theories and numerical ...

  10. Anti-reflection zinc oxide nanocones for higher efficiency thin-film silicon solar cells

    E-Print Network [OSTI]

    Mailoa, Jonathan P

    2012-01-01

    Thin film silicon solar cells, which are commonly made from microcrystalline silicon ([mu]c-Si) or amorphous silicon (a-Si), have been considered inexpensive alternatives to thick polycrystalline silicon (polysilicon) solar ...

  11. CIGS Thin-Film Solar Cell Research at NREL: FY04 Results and...

    Office of Scientific and Technical Information (OSTI)

    No. DE-AC36-99-GO10337 Conference Paper NRELCP-520-37020 January 2005 CIGS Thin-Film Solar Cell Research at NREL: FY04 Results and Accomplishments K. Ramanathan, R.N....

  12. Intermixing at the absorber-buffer layer interface in thin-film...

    Office of Scientific and Technical Information (OSTI)

    Intermixing at the absorber-buffer layer interface in thin-film solar cells: The electronic effects of point defects in Cu(In,Ga)(Se,S)sub 2 and Cusub 2ZnSn(Se,S)sub 4...

  13. Efficiency calculations of thin-film GaAs solar cells on Si substrates

    SciTech Connect (OSTI)

    Yamaguchi, M.; Amano, C.

    1985-11-01

    Dislocation effect upon the efficiency of single-crystal thin-film AlGaAs-GaAs heteroface solar cells on Si substrates is analyzed. Solar-cell properties are calculated based on a simple model; in the model, dislocations act as recombination centers to reduce the minority-carrier diffusion length in each layer and increase the space-charge layer recombination current. Numerical analysis is also carried out to optimize thin-film AlGaAs-GaAs heteroface solar-cell structures. The fabrication of thin-film AlGaAs-GaAs heteroface solar cells with a practical efficiency larger than 18% on Si substrates appears possible if the dislocation density in the thin-film GaAs layer is less than 10/sup 6/ cm/sup -2/.

  14. Apparatus for making cathodo- and photo- luminescent measurements of thin film phosphors 

    E-Print Network [OSTI]

    Babuchna, Paul Michael

    1998-01-01

    the understanding of the thin film phosphor, tungsten doped zinc oxide. Principally, a vacuum system is constructed and provides for both photo-and cathode-phosphor excitations. A measurement capability is then included. Finally, additions are mentioned...

  15. Scanning tunneling microscopic studies of SiO2 thin film supported metal nano-clusters 

    E-Print Network [OSTI]

    Min, Byoung Koun

    2005-11-01

    This dissertation is focused on understanding heterogeneous metal catalysts supported on oxides using a model catalyst system of SiO2 thin film supported metal nano-clusters. The primary technique applied to this study is scanning tunneling...

  16. Materials properties of pharmaceutical formulations for thin-film-tablet continuous manufacturing

    E-Print Network [OSTI]

    Barcena, Jose R. (Jose Roberto)

    2012-01-01

    The development of manufacturing tablets in a continuous way has been possible greatly to the fabrication of polymer based thin-films. It is estimated that the pharmaceutical industry loses as much as a 25% on revenues ...

  17. Electrodynamic Properties of Single-Crystal and Thin-Film Strontium Titanate

    SciTech Connect (OSTI)

    Findikoglu, A.T.; Jia, Q.; Reagor, D.W.; Kwon, C.; Rasmussen, K.O.

    1999-05-13

    The authors present a comparative study of broadband electrodynamic properties of coplanar waveguides made from nonlinear dielectric single-crystal and thin-film SrTiO{sub 3} (STO) with high-temperature superconducting thin-film YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} electrodes. The waveguides that use single-crystal STO exhibit a monotonic increase in refractive index, dielectric nonlinearity, and dissipation with decreasing temperature (from 80 K to 20 K), whereas those based on thin-film STO show similar but weaker effects with increasing temperature. Under dc bias, both types of waveguides show reduced refractive index, but dissipation increases in the case of single-crystal STO, while it decreases in the case of STO thin-films.

  18. Evaluation of polyelectrolyte multilayer thin-film coated microneedle arrays for transcutaneous vaccine delivery

    E-Print Network [OSTI]

    Fung, Peter W. (Peter Waitak)

    2011-01-01

    The skin is an ideal organ for the safe and convenient delivery of vaccines, small molecules, and other biologics. Members of the Irvine and Hammond groups have developed a polyelectrolyte multilayer thin film-coated ...

  19. Engineering Al-based Thin Film Materials for Power Devices and Energy Storage Applications

    E-Print Network [OSTI]

    Perng, Ya-Chuan

    2012-01-01

    and J. P. Chang, “Atomic layer deposition of Pb(Zr, Ti)O xfilms deposited by atomic layer deposition on 4H-SiC,” Appl.AlN Thin Films by Atomic Layer Deposition on Wide Bandgap

  20. A Review of Thin Film Crystalline Silicon for Solar Cell Applications. Part 1 : Native Substrates.

    E-Print Network [OSTI]

    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 5.5 Epilift process - Centre for Sustainable Energy Systems, ANU Systems Engineering Department, The Australian National University, ACT 0200, Australia. Email : michelleA Review of Thin Film Crystalline Silicon for Solar Cell Applications. Part 1 : Native Substrates

  1. Bi-Sr-Ca-Cu-O thin films grown by flash evaporation and pulsed laser deposition 

    E-Print Network [OSTI]

    Ganapathy Subramanian, Santhana

    2004-09-30

    -phase 2212 films were grown on a MgO substrate using the pulsed laser deposition technique from commercially available 2212 powder. The effect of annealing on the thin films was also studied....

  2. Technological assessment of light-trapping technology for thin-film Si solar cell

    E-Print Network [OSTI]

    Susantyoko, Rahmat Agung

    2009-01-01

    The proposed light trapping technology of Distributed Bragg Reflector (DBR) with Diffraction Grating (DG) and Anti-Reflection Coating (ARC) for thin film Si solar cell was analyzed from the technology, market, and ...

  3. Defect engineering of cuprous oxide thin-films for photovoltaic applications

    E-Print Network [OSTI]

    Lee, Yun Seog

    2013-01-01

    Thin-film solar cells are promising for renewable-energy applications due to their low material usage and inexpensive manufacturing potential, making them compatible with terawatts-level deployment. Cuprous oxide (Cu?O) ...

  4. Solid state thin film battery having a high temperature lithium alloy anode

    DOE Patents [OSTI]

    Hobson, David O. (Oak Ridge, TN)

    1998-01-01

    An improved rechargeable thin-film lithium battery involves the provision of a higher melting temperature lithium anode. Lithium is alloyed with a suitable solute element to elevate the melting point of the anode to withstand moderately elevated temperatures.

  5. A dual-laser interferometry system for thin film measurements in thermal vapor deposition applications

    E-Print Network [OSTI]

    Yin, Allen Shiping

    2012-01-01

    Lithography processes harnessing the phase change of the chemically inert carbon dioxide as a resist have been shown as a possible alternative to patterning thin film organic semiconductors and metals. The ability to control ...

  6. Amorphous Si Thin Film Based Photocathodes with High Photovoltage for Efficient Hydrogen Production

    E-Print Network [OSTI]

    Javey, Ali

    Amorphous Si Thin Film Based Photocathodes with High Photovoltage for Efficient Hydrogen Production for solar hydrogen production. With platinum as prototypical cocatalyst, a photocurrent onset potential of 0 for solar hydrogen production. KEYWORDS: Water splitting, hydrogen production, photochemistry, high

  7. Design and modeling of a PZT thin film based piezoelectric micromachined ultrasonic transducer (PMUT)

    E-Print Network [OSTI]

    Smyth, Katherine Marie

    2012-01-01

    The design and modelling framework for a piezoelectric micromachined ultrasonic transducer (PMUT) based on the piezoelectric thin film deposition of lead zirconate titanate (PZT) is defined. Through high frequency vibration ...

  8. Role of Polycrystalline Thin-Film PV Technologies in Competitive PV Module Markets: Preprint

    SciTech Connect (OSTI)

    von Roedern, B.; Ullal, H. S.

    2008-05-01

    This paper discusses the developments in thin-film PV technologies and provides an outlook on future commercial module efficiencies achievable based on today's knowledge about champion cell performance.

  9. Enhanced absorption of thin-film photovoltaic cells using an optical cavity

    E-Print Network [OSTI]

    Hsu, Wei-Chun

    We show via numerical simulations that the absorption and solar energy conversion efficiency of a thin-film photovoltaic (PV) cell can be significantly enhanced by embedding it into an optical cavity. A reflective ...

  10. Surface spectroscopic characterization of oxide thin films and bimetallic model catalysts 

    E-Print Network [OSTI]

    Wei, Tao

    2009-05-15

    Oxide thin films and bimetallic model catalysts have been studied using metastable impact electron spectroscopy (MIES), ultraviolet photoelectron spectroscopy (UPS), low energy ion scattering spectroscopy (LEISS), X – ray photoelectron spectroscopy...

  11. Volumetric plasmonic resonator architecture for thin-film solar cells Mustafa Akin Sefunc,a

    E-Print Network [OSTI]

    Demir, Hilmi Volkan

    Volumetric plasmonic resonator architecture for thin-film solar cells Mustafa Akin Sefunc,a Ali; published online 4 March 2011 We propose and demonstrate a design concept of volumetric plasmonic resonators

  12. Formation of thin film Tl-based high-Tc? superconducting oxides from amorphous alloy precursors 

    E-Print Network [OSTI]

    Williams, John Charles

    1991-01-01

    FORMATION OF THIN FILM Tl-BASED HIGH-Tc SUPERCONDUCTING OXIDES FROM AMORPHOUS ALLOY PRECURSORS A Thesis JOHN CHARLES WILLIAMS Submitted to the Once of Graduate Studies of Texas A&M University in partial fulfillment of the requirements... for the degree of MASTER OF SCIENCE December 1991 Major Subject: Physics FORMATION OF THIN FILM Tl BASED HIGH Tc SUPERCONDUCTING OXIDES FROM AMORPHOUS ALLOY PRECURSORS A Thesis JOHN CHARLES WILLIAMS Approved as to style and content by: Donald G. Naugle...

  13. Thin-film Sb2Se3 photovoltaics with oriented one-dimensional ribbons and benign

    E-Print Network [OSTI]

    Sargent, Edward H. "Ted"

    to the substrate, and produced Sb2Se3 thin-film solar cells with a certified device efficiency of 5.6%. Our results are one of the major limiting factors for high-efficiency thin-film solar cells. We began with first cells based on inorganic absorbers, such as Si, GaAs, CdTe and Cu(In,Ga)Se2, permit a high device

  14. Two-photon induced fabrication of gold microstructures in polystyrene sulfonate thin films using a ruthenium(II) dye as photoinitiator

    SciTech Connect (OSTI)

    Vurth, Laeticia; Baldeck, Patrice; Stephan, Olivier [Laboratoire de Spectrometrie Physique, Universite Joseph Fourier, CNRS (UMR 5588), BP 87, 38402 Saint Martin d'heres Cedex (France); Vitrant, Guy [Institut Microelectronique Electromagnetisme et Photonique, ENSERG-INPG, CNRS (UMR 5130), BP 257, 38016 Grenoble Cedex 1 (France)

    2008-04-28

    Gold microstructures are produced with a femtosecond laser in thin films of a polystyrene sulfonate matrix containing gold ions. Two-photon induced metal reduction is obtained by addition of 0.1 wt % of ruthenium(II)tris(bipyridine) in the formulation. Laser power is reduced to 5 mW, thereby limiting thermal effects. Lines of typically 150 nm heights and 1 {mu}m widths are fabricated as well as freestanding bidimensional structures. An additional electroless plating step produces gold structures with conductivities only ten times smaller than the bulk metal.

  15. Free-Space Time-Domain Method for Measuring Thin Film Dielectric Properties

    DOE Patents [OSTI]

    Li, Ming; Zhang, Xi-Cheng; Cho, Gyu Cheon

    2000-05-02

    A non-contact method for determining the index of refraction or dielectric constant of a thin film on a substrate at a desired frequency in the GHz to THz range having a corresponding wavelength larger than the thickness of the thin film (which may be only a few microns). The method comprises impinging the desired-frequency beam in free space upon the thin film on the substrate and measuring the measured phase change and the measured field reflectance from the reflected beam for a plurality of incident angles over a range of angles that includes the Brewster's angle for the thin film. The index of refraction for the thin film is determined by applying Fresnel equations to iteratively calculate a calculated phase change and a calculated field reflectance at each of the plurality of incident angles, and selecting the index of refraction that provides the best mathematical curve fit with both the dataset of measured phase changes and the dataset of measured field reflectances for each incident angle. The dielectric constant for the thin film can be calculated as the index of refraction squared.

  16. Electron-beam-evaporated thin films of hafnium dioxide for fabricating electronic devices

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Xiao, Zhigang; Kisslinger, Kim

    2015-06-17

    Thin films of hafnium dioxide (HfO2) are widely used as the gate oxide in fabricating integrated circuits because of their high dielectric constants. In this paper, the authors report the growth of thin films of HfO2 using e-beam evaporation, and the fabrication of complementary metal-oxide semiconductor (CMOS) integrated circuits using this HfO2 thin film as the gate oxide. The authors analyzed the thin films using high-resolution transmission electron microscopy and electron diffraction, thereby demonstrating that the e-beam-evaporation-grown HfO2 film has a polycrystalline structure and forms an excellent interface with silicon. Accordingly, we fabricated 31-stage CMOS ring oscillator to test themore »quality of the HfO2 thin film as the gate oxide, and obtained excellent rail-to-rail oscillation waveforms from it, denoting that the HfO2 thin film functioned very well as the gate oxide.« less

  17. Wake and wave resistance on viscous thin films

    E-Print Network [OSTI]

    Ledesma-Alonso, René; Salez, Thomas; Raphaël, Elie

    2015-01-01

    The effect of an external pressure disturbance, being displaced with a constant speed along the free surface of a viscous thin film, is studied theoretically in the lubrication approximation in one- and two-dimensional geometries. In the comoving frame, the imposed pressure field creates a stationary deformation of the interface - a wake - that spatially vanishes in the far region. The shape of the wake and the way it vanishes depend on both the speed and size of the external source and the properties of the film. The wave resistance, namely the force that has to be externally furnished in order to maintain the wake, is analysed in details. For finite-size pressure disturbances, it increases with the speed, up to a certain transition value above which a monotonic decrease occurs. The role of the horizontal extent of the pressure field is studied as well, revealing that for a smaller disturbance the latter transition occurs at higher speed. Eventually, for a Dirac pressure source, the wave resistance either sa...

  18. 2010 Thin Film & Small Scale Mechanical Behavior Gordon Research Conference

    SciTech Connect (OSTI)

    Dr. Thomas Balk

    2010-07-30

    Over the past decades, it has been well established that the mechanical behavior of materials changes when they are confined geometrically at least in one dimension to small scale. It is the aim of the 2010 Gordon Conference on 'Thin Film and Small Scale Mechanical Behavior' to discuss cutting-edge research on elastic, plastic and time-dependent deformation as well as degradation mechanisms like fracture, fatigue and wear at small scales. As in the past, the conference will benefit from contributions from fundamental studies of physical mechanisms linked to material science and engineering reaching towards application in modern applications ranging from optical and microelectronic devices and nano- or micro-electrical mechanical systems to devices for energy production and storage. The conference will feature entirely new testing methodologies and in situ measurements as well as recent progress in atomistic and micromechanical modeling. Particularly, emerging topics in the area of energy conversion and storage, such as material for batteries will be highlighted. The study of small-scale mechanical phenomena in systems related to energy production, conversion or storage offer an enticing opportunity to materials scientists, who can provide new insight and investigate these phenomena with methods that have not previously been exploited.

  19. Highly textured oxypnictide superconducting thin films on metal substrates

    SciTech Connect (OSTI)

    Iida, Kazumasa, E-mail: iida@nuap.nagoya-u.ac.jp; Kurth, Fritz; Grinenko, Vadim; Hänisch, Jens [Institute for Metallic Materials, IFW Dresden, D-01171 Dresden (Germany); Chihara, Masashi; Sumiya, Naoki; Hatano, Takafumi; Ikuta, Hiroshi [Department of Crystalline Materials Science, Nagoya University, Chikusa, Nagoya 464-8603 (Japan); Ichinose, Ataru; Tsukada, Ichiro [Central Research Institute of Electric Power Industry, 2-6-1 Nagasaka, Yokosuka, Kanagawa 240-0196 (Japan); Matias, Vladimir [iBeam Materials, Inc., 2778A Agua Fria Street, Santa Fe, New Mexico 87507 (United States); Holzapfel, Bernhard [Institute for Technical Physics, Karlsruhe Institute of Technology, Hermann von Helmholtz-Platz 1, D-76344 Eggenstein-Leopoldshafen (Germany)

    2014-10-27

    Highly textured NdFeAs(O,F) thin films have been grown on ion beam assisted deposition-MgO/Y{sub 2}O{sub 3}/Hastelloy substrates by molecular beam epitaxy. The oxypnictide coated conductors showed a superconducting transition temperature (T{sub c}) of 43?K with a self-field critical current density (J{sub c}) of 7.0×10{sup 4}?A/cm{sup 2} at 5?K, more than 20 times higher than powder-in-tube processed SmFeAs(O,F) wires. Albeit higher T{sub c} as well as better crystalline quality than Co-doped BaFe{sub 2}As{sub 2} coated conductors, in-field J{sub c} of NdFeAs(O,F) was lower than that of Co-doped BaFe{sub 2}As{sub 2}. These results suggest that grain boundaries in oxypnictides reduce J{sub c} significantly compared to that in Co-doped BaFe{sub 2}As{sub 2} and, hence biaxial texture is necessary for high J{sub c.}.

  20. Scaling law analysis of paraffin thin films on different surfaces

    SciTech Connect (OSTI)

    Dotto, M. E. R.; Camargo, S. S. Jr. [Engenharia Metalurgica e de Materials, Universidade Federal do Rio de Janeiro, Cx. Postal 68505, Rio de Janeiro, RJ, CEP 21945-970 (Brazil)

    2010-01-15

    The dynamics of paraffin deposit formation on different surfaces was analyzed based on scaling laws. Carbon-based films were deposited onto silicon (Si) and stainless steel substrates from methane (CH{sub 4}) gas using radio frequency plasma enhanced chemical vapor deposition. The different substrates were characterized with respect to their surface energy by contact angle measurements, surface roughness, and morphology. Paraffin thin films were obtained by the casting technique and were subsequently characterized by an atomic force microscope in noncontact mode. The results indicate that the morphology of paraffin deposits is strongly influenced by substrates used. Scaling laws analysis for coated substrates present two distinct dynamics: a local roughness exponent ({alpha}{sub local}) associated to short-range surface correlations and a global roughness exponent ({alpha}{sub global}) associated to long-range surface correlations. The local dynamics is described by the Wolf-Villain model, and a global dynamics is described by the Kardar-Parisi-Zhang model. A local correlation length (L{sub local}) defines the transition between the local and global dynamics with L{sub local} approximately 700 nm in accordance with the spacing of planes measured from atomic force micrographs. For uncoated substrates, the growth dynamics is related to Edwards-Wilkinson model.

  1. Residual ferroelectricity in barium strontium titanate thin film tunable dielectrics

    SciTech Connect (OSTI)

    Garten, L. M., E-mail: lmg309@psu.edu; Trolier-McKinstry, S. [Department of Materials Science and Engineering and Materials Research Institute, The Pennsylvania State University, University Park, Pennsylvania 16802 (United States); Lam, P.; Harris, D.; Maria, J.-P. [Department of Materials Science and Engineering, North Carolina State University, Raleigh, North Carolina 27607 (United States)

    2014-07-28

    Loss reduction is critical to develop Ba{sub 1?x}Sr{sub x}TiO{sub 3} thin film tunable microwave dielectric components and dielectric energy storage devices. The presence of ferroelectricity, and hence the domain wall contributions to dielectric loss, will degrade the tunable performance in the microwave region. In this work, residual ferroelectricity—a persistent ferroelectric response above the global phase transition temperature—was characterized in tunable dielectrics using Rayleigh analysis. Chemical solution deposited Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} films, with relative tunabilities of 86% over 250?kV/cm at 100?kHz, demonstrated residual ferroelectricity 65?°C above the ostensible paraelectric transition temperature. Frequency dispersion observed in the dielectric temperature response was consistent with the presence of nanopolar regions as one source of residual ferroelectricity. The application of AC electric field for the Rayleigh analysis of these samples led to a doubling of the dielectric loss for fields over 10?kV/cm at room temperature.

  2. Hydrogen adsorption in thin films of Prussian blue analogue

    SciTech Connect (OSTI)

    Yang, Dali [Los Alamos National Laboratory; Ding, Vivian [Los Alamos National Laboratory; Luo, Junhua [Los Alamos National Laboratory; Currier, Robert P [Los Alamos National Laboratory; Obrey, Steve [Los Alamos National Laboratory; Zhao, Yusheng [Los Alamos National Laboratory

    2008-01-01

    Quartz crystal microbalance with dissipation (QCM-D) measurement was used to investigate the kinetics of the molecular hydrogen adsorption into thin films of prussian blue analogues - Cu{sub 3}[Co(CN){sub 6}]{sub 2} at ambient conditions. Although the equilibrium adsorption seems to be independent of the thickness, the adsorption rate substantially decreases with the thickness of the films. In addition, the reversibility of H{sub 2} adsorption into the Cu{sub 3}[Co(CN){sub 6}]{sub 2} films was investigated. The results indicate that the Cu{sub 3}[Co(CN){sub 6}]{sub 2} maily interacts with H{sub 2} molecules physically. The highest H{sub 2} uptake by the Cu{sub 3}[Co(CN){sub 6}]{sub 2} films is obtained when the gas phase is stagnant inside the testing cell. However, the unusual high H{sub 2} uptake obtained from the QCM-D measurement makes us question how reliable this analytic methodology is.

  3. Nanopatterning of ultrananocrystalline diamond thin films via block copolymer lithography.

    SciTech Connect (OSTI)

    Ramanathan, M.; Darling, S. B.; Sumant, A. V.; Auciello, O.

    2010-07-01

    Nanopatterning of diamond surfaces is critical for the development of diamond-based microelectromechanical system/nanoelectromechanical system (MEMS/NEMS), such as resonators or switches. Micro-/nanopatterning of diamond materials is typically done using photolithography or electron beam lithography combined with reactive ion etching (RIE). In this work, we demonstrate a simple process, block copolymer (BCP) lithography, for nanopatterning of ultrananocrystalline diamond (UNCD) films to produce nanostructures suitable for the fabrication of NEMS based on UNCD. In BCP lithography, nanoscale self-assembled polymeric domains serve as an etch mask for pattern transfer. The authors used thin films of a cylinder-forming organic-inorganic BCP, poly(styrene-block-ferrocenyldimethylsilane), PS-b-PFS, as an etch mask on the surface of UNCD films. Orientational control of the etch masking cylindrical PFS blocks is achieved by manipulating the polymer film thickness in concert with the annealing treatment. We have observed that the surface roughness of UNCD layers plays an important role in transferring the pattern. Oxygen RIE was used to etch the exposed areas of the UNCD film underneath the BCP. Arrays of both UNCD posts and wirelike structures have been created using the same starting polymeric materials as the etch mask.

  4. Thin-film fiber optic hydrogen and temperature sensor system

    DOE Patents [OSTI]

    Nave, S.E.

    1998-07-21

    The invention discloses a sensor probe device for monitoring of hydrogen gas concentrations and temperatures by the same sensor probe. The sensor probe is constructed using thin-film deposition methods for the placement of a multitude of layers of materials sensitive to hydrogen concentrations and temperature on the end of a light transparent lens located within the sensor probe. The end of the lens within the sensor probe contains a lens containing a layer of hydrogen permeable material which excludes other reactive gases, a layer of reflective metal material that forms a metal hydride upon absorbing hydrogen, and a layer of semi-conducting solid that is transparent above a temperature dependent minimum wavelength for temperature detection. The three layers of materials are located at the distal end of the lens located within the sensor probe. The lens focuses light generated by broad-band light generator and connected by fiber-optics to the sensor probe, onto a reflective metal material layer, which passes through the semi-conducting solid layer, onto two optical fibers located at the base of the sensor probe. The reflected light is transmitted over fiber optic cables to a spectrometer and system controller. The absence of electrical signals and electrical wires in the sensor probe provides for an elimination of the potential for spark sources when monitoring in hydrogen rich environments, and provides a sensor free from electrical interferences. 3 figs.

  5. Ultrafast transient reflectance of epitaxial semiconducting perovskite thin films

    SciTech Connect (OSTI)

    Smolin, S. Y.; Guglietta, G. W.; Baxter, J. B. E-mail: smay@coe.drexel.edu; Scafetta, M. D.; May, S. J. E-mail: smay@coe.drexel.edu

    2014-07-14

    Ultrafast pump-probe transient reflectance (TR) spectroscopy was used to study carrier dynamics in an epitaxial perovskite oxide thin film of LaFeO{sub 3} (LFO) with a thickness of 40 unit cells (16?nm) grown by molecular beam epitaxy on (LaAlO{sub 3}){sub 0.3}(Sr{sub 2}AlTaO{sub 6}){sub 0.7} (LSAT). TR spectroscopy shows two negative transients in reflectance with local maxima at ?2.5?eV and ?3.5?eV which correspond to two optical transitions in LFO as determined by ellipsometry. The kinetics at these transients were best fit with an exponential decay model with fast (5–40 ps), medium (?200 ps), and slow (??3?ns) components that we attribute mainly to recombination of photoexcited carriers. Moreover, these reflectance transients did not completely decay within the observable time window, indicating that ?10% of photoexcited carriers exist for at least 3?ns. This work illustrates that TR spectroscopy can be performed on thin (<20?nm) epitaxial oxide films to provide a quantitative understanding of recombination lifetimes, which are important parameters for the potential utilization of perovskite films in photovoltaic and photocatalytic applications.

  6. Thin-film fiber optic hydrogen and temperature sensor system

    DOE Patents [OSTI]

    Nave, Stanley E. (Evans, GA)

    1998-01-01

    The invention discloses a sensor probe device for monitoring of hydrogen gas concentrations and temperatures by the same sensor probe. The sensor probe is constructed using thin-film deposition methods for the placement of a multitude of layers of materials sensitive to hydrogen concentrations and temperature on the end of a light transparent lens located within the sensor probe. The end of the lens within the sensor probe contains a lens containing a layer of hydrogen permeable material which excludes other reactive gases, a layer of reflective metal material that forms a metal hydride upon absorbing hydrogen, and a layer of semi-conducting solid that is transparent above a temperature dependent minimum wavelength for temperature detection. The three layers of materials are located at the distal end of the lens located within the sensor probe. The lens focuses light generated by broad-band light generator and connected by fiber-optics to the sensor probe, onto a reflective metal material layer, which passes through the semi-conducting solid layer, onto two optical fibers located at the base of the sensor probe. The reflected light is transmitted over fiberoptic cables to a spectrometer and system controller. The absence of electrical signals and electrical wires in the sensor probe provides for an elimination of the potential for spark sources when monitoring in hydrogen rich environments, and provides a sensor free from electrical interferences.

  7. Method for bonding thin film thermocouples to ceramics

    DOE Patents [OSTI]

    Kreider, Kenneth G. (Potomac, MD)

    1993-01-01

    A method is provided for adhering a thin film metal thermocouple to a ceramic substrate used in an environment up to 700 degrees Centigrade, such as at a cylinder of an internal combustion engine. The method includes the steps of: depositing a thin layer of a reactive metal on a clean ceramic substrate; and depositing thin layers of platinum and a platinum-10% rhodium alloy forming the respective legs of the thermocouple on the reactive metal layer. The reactive metal layer serves as a bond coat between the thin noble metal thermocouple layers and the ceramic substrate. The thin layers of noble metal are in the range of 1-4 micrometers thick. Preferably, the ceramic substrate is selected from the group consisting of alumina and partially stabilized zirconia. Preferably, the thin layer of reactive metal is in the range of 0.015-0.030 micrometers (15-30 nanometers) thick. The preferred reactive metal is chromium. Other reactive metals may be titanium or zirconium. The thin layer of reactive metal may be deposited by sputtering in ultra high purity argon in a vacuum of approximately 2 milliTorr (0.3 Pascals).

  8. Dissociation of dilute immiscible copper alloy thin films

    SciTech Connect (OSTI)

    Barmak, K.; Lucadamo, G. A.; Cabral, C. Jr.; Lavoie, C.; Harper, J. M. E.

    2000-03-01

    The dissociation behavior of dilute, immiscible Cu-alloy thin films is found to fall into three broad categories that correlate most closely with the form of the Cu-rich end of the binary alloy phase diagrams. Available thermodynamic and tracer diffusion data shed further light on alloy behavior. Eight alloying elements were selected for these studies, with five elements from groups 5 and 6, two from group 8, and one from group 11 of the periodic table. They are respectively V, Nb, Ta, Cr, Mo, Fe, Ru, and Ag. The progress of precipitation in approximately 500-nm-thick alloy films, containing 2.5-3.8 at. % solute, was followed with in situ resistance and stress measurements as well as with in situ synchrotron x-ray diffraction. In addition, texture analysis and transmission electron microscopy were used to investigate the evolution of microstructure and texture of Cu(Ta) and Cu(Ag). For all eight alloys, dissociation occurred upon heating, with the rejection of solute and evolution of microstructure often occurring in multiple steps that range over several hundred degrees between approximately 100 and 900 degree sign C. However, in most cases, substantial reductions in resistivity of the films took place below 400 degree sign C, at temperatures of interest to copper metallization schemes for silicon chip technology. (c) 2000 American Institute of Physics.

  9. Ambipolar charge transport in microcrystalline silicon thin-film transistors

    SciTech Connect (OSTI)

    Knipp, Dietmar; Marinkovic, M.; Chan, Kah-Yoong; Gordijn, Aad; Stiebig, Helmut

    2011-01-15

    Hydrogenated microcrystalline silicon ({mu}c-Si:H) is a promising candidate for thin-film transistors (TFTs) in large-area electronics due to high electron and hole charge carrier mobilities. We report on ambipolar TFTs based on {mu}c-Si:H prepared by plasma-enhanced chemical vapor deposition at temperatures compatible with flexible substrates. Electrons and holes are directly injected into the {mu}c-Si:H channel via chromium drain and source contacts. The TFTs exhibit electron and hole charge carrier mobilities of 30-50 cm{sup 2}/V s and 10-15 cm{sup 2}/V s, respectively. In this work, the electrical characteristics of the ambipolar {mu}c-Si:H TFTs are described by a simple analytical model that takes the ambipolar charge transport into account. The analytical expressions are used to model the transfer curves, the potential and the net surface charge along the channel of the TFTs. The electrical model provides insights into the electronic transport of ambipolar {mu}c-Si:H TFTs.

  10. High Efficiency Thin Film CdTe and a-Si Based Solar Cells Final Technical Report for the Period

    E-Print Network [OSTI]

    Deng, Xunming

    High Efficiency Thin Film CdTe and a-Si Based Solar Cells Final Technical Report for the PeriodTe-based thin-film solar cells and on high efficiency a-Si-based thin-film solar cells. Phases I and II have-SiGe bottom cells. · Studied the sputter deposition of ITO films for the top electrode on a-Si cells and found

  11. Nitrogen-doped cuprous oxide as a p-type hole-transporting layer in thin-film solar cells

    E-Print Network [OSTI]

    Nitrogen-doped cuprous oxide as a p-type hole- transporting layer in thin-film solar cells Yun Seog-transparent tunnel junction to a back-contact. We fabricate Cu2O-based heterojunction thin-film solar cells-factor and power conversion efficiency of the solar cells. Cu2O:N thin-films may also be useful in other

  12. Growth and Oxidation of Thin Film Al(2)Cu

    SciTech Connect (OSTI)

    SON,KYUNG-AH; MISSERT,NANCY A.; BARBOUR,J. CHARLES; HREN,J.J.; COPELAND,ROBERT GUILD; MINOR,KENNETH G.

    2000-01-18

    Al{sub 2}Cu thin films ({approx} 382 nm) are fabricated by melting and resolidifying Al/Cu bilayers in the presence of a {micro} 3 nm Al{sub 2}O{sub 3} passivating layer. X-ray Photoelectron Spectroscopy (XPS) measures a 1.0 eV shift of the Cu2p{sub 3/2} peak and a 1.6 eV shift of the valence band relative to metallic Cu upon Al{sub 2}Cu formation. Scanning Electron microscopy (SEM) and Electron Back-Scattered Diffraction (EBSD) show that the Al{sub 2}Cu film is composed of 30-70 {micro}m wide and 10-25 mm long cellular grains with (110) orientation. The atomic composition of the film as estimated by Energy Dispersive Spectroscopy (EDS) is 67 {+-} 2% Al and 33 {+-} 2% Cu. XPS scans of Al{sub 2}O{sub 3}/Al{sub 2}Cu taken before and after air exposure indicate that the upper Al{sub 2}Cu layers undergo further oxidation to Al{sub 2}O{sub 3} even in the presence of {approx} 5 nm Al{sub 2}O{sub 3}. The majority of Cu produced from oxidation is believed to migrate below the Al{sub 2}O{sub 3} layers, based upon the lack of evidence for metallic Cu in the XPS scans. In contrast to Al/Cu passivated with Al{sub 2}O{sub 3}, melting/resolidifying the Al/Cu bilayer without Al{sub 2}O{sub 3} results in phase-segregated dendritic film growth.

  13. Low Cost Thin Film Building-Integrated Photovoltaic Systems

    SciTech Connect (OSTI)

    Dr. Subhendu Guha; Dr. Jeff Yang

    2012-05-25

    The goal of the program is to develop 'LOW COST THIN FILM BUILDING-INTEGRATED PV SYSTEMS'. Major focus was on developing low cost solution for the commercial BIPV and rooftop PV market and meet DOE LCOE goal for the commercial market segment of 9-12 cents/kWh for 2010 and 6-8 cents/kWh for 2015. We achieved the 2010 goal and were on track to achieve the 2015 goal. The program consists of five major tasks: (1) modules; (2) inverters and BOS; (3) systems engineering and integration; (4) deployment; and (5) project management and TPP collaborative activities. We successfully crossed all stage gates and surpassed all milestones. We proudly achieved world record stable efficiencies in small area cells (12.56% for 1cm2) and large area encapsulated modules (11.3% for 800 cm2) using a triple-junction amorphous silicon/nanocrystalline silicon/nanocrystalline silicon structure, confirmed by the National Renewable Energy Laboratory. We collaborated with two inverter companies, Solectria and PV Powered, and significantly reduced inverter cost. We collaborated with three universities (Syracuse University, University of Oregon, and Colorado School of Mines) and National Renewable Energy Laboratory, and improved understanding on nanocrystalline material properties and light trapping techniques. We jointly published 50 technical papers in peer-reviewed journals and International Conference Proceedings. We installed two 75kW roof-top systems, one in Florida and another in New Jersey demonstrating innovative designs. The systems performed satisfactorily meeting/exceeding estimated kWh/kW performance. The 50/50 cost shared program was a great success and received excellent comments from DOE Manager and Technical Monitor in the Final Review.

  14. PROJECT PROFILE: High-resolution Investigations of Transport Limiting Defects and Interfaces in Thin-Film Photovoltaic Devices

    Broader source: Energy.gov [DOE]

    This project will develop the capability of high-resolution transport imaging in photovoltaic (PV) devices, which is useful for improving polycrystalline thin-film PV materials.

  15. Effect of deposition times on structure of Ga-doped ZnO thin films as humidity sensor

    SciTech Connect (OSTI)

    Khalid, Faridzatul Shahira; Awang, Rozidawati [School of Applied Physics, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia)

    2014-09-03

    Gallium doped zinc oxide (GZO) has good electrical property. It is widely used as transparent electrode in photovoltaic devices, and sensing element in gas and pressure sensors. GZO thin film was prepared using magnetron sputtering. Film deposition times were set at 10, 15, 20, 25 and 30 minutes to get samples of different thickness. X-ray diffraction (XRD) was used to determine the structure of GZO thin films. Structure for GZO thin film is hexagonal wurtzite structure. Morphology and thickness of GZO thin films was observed from FESEM micrographs. Grain size and thickness of thin films improved with increasing deposition times. However, increasing the thickness of thin films occur below 25 minutes only. Electrical properties of GZO thin films were studied using a four-point probe technique. The changes in the structure of the thin films lead to the changed of their electrical properties resulting in the reduction of the film resistance. These thin films properties significantly implying the potential application of the sample as a humidity sensor.

  16. Magnetoelectric coupling of multiferroic chromium doped barium titanate thin film probed by magneto-impedance spectroscopy

    SciTech Connect (OSTI)

    Shah, Jyoti Kotnala, Ravinder K. E-mail: rkkotnala@gmail.com

    2014-04-07

    Thin film of BaTiO{sub 3} doped with 0.1?at.?% Cr (Cr:BTO) has been prepared by pulsed laser deposition technique. Film was deposited on Pt/SrTiO{sub 3} substrate at 500?°C in 50 mTorr Oxygen gas pressure using KrF (298 nm) laser. Polycrystalline growth of single phase Cr:BTO thin film has been confirmed by grazing angle X-ray diffraction. Cr:BTO film exhibited remnant polarization 6.4??C/cm{sup 2} and 0.79?MV/cm coercivity. Magnetization measurement of Cr:BTO film showed magnetic moment 12 emu/cc. Formation of weakly magnetic domains has been captured by magnetic force microscopy. Theoretical impedance equation fitted to experimental data in Cole-Cole plot for thin film in presence of transverse magnetic field resolved the increase in grain capacitance from 4.58?×?10{sup ?12} to 5.4?×?10{sup ?11}?F. Film exhibited high value 137?mV/cm-Oe magneto-electric (ME) coupling coefficient at room temperature. The high value of ME coupling obtained can reduce the typical processing steps involved in multilayer deposition to obtain multiferrocity in thin film. Barium titanate being best ferroelectric material has been tailored to be multiferroic by non ferromagnetic element, Cr, doping in thin film form opens an avenue for more stable and reliable spintronic material for low power magnetoelectric random excess memory applications.

  17. Structural and optical properties of DC reactive magnetron sputtered zinc aluminum oxide thin films

    SciTech Connect (OSTI)

    Kumar, B. Rajesh; Rao, T. Subba

    2014-10-15

    Highly transparent conductive Zinc Aluminum Oxide (ZAO) thin films have been deposited on glass substrates using DC reactive magnetron sputtering method. The thin films were deposited at 200 °C and post-deposition annealing from 15 to 90 min. XRD patterns of ZAO films exhibit only (0 0 2) diffraction peak, indicating that they have c-axis preferred orientation perpendicular to the substrate. Scanning electron microscopy (SEM) is used to study the surface morphology of the films. The grain size obtained from SEM images of ZAO thin films are found to be in the range of 20 - 26 nm. The minimum resistivity of 1.74 × 10{sup ?4} ? cm and an average transmittance of 92% are obtained for the thin film post annealed for 30 min. The optical band gap of ZAO thin films increased from 3.49 to 3.60 eV with the increase of annealing time due to Burstein-Moss effect. The optical constants refractive index (n) and extinction coefficient (k) were also determined from the optical transmission spectra.

  18. Studies on optoelectronic properties of DC reactive magnetron sputtered CdTe thin films

    SciTech Connect (OSTI)

    Kumar, B. Rajesh, E-mail: rajphyind@gmail.com [Department of Physics, Sri Venkateswara University, Tirupati - 517 502, A.P, India and Department of Physics, Sri Krishnadevaraya University, Anantapur - 515 003, A.P (India); Hymavathi, B.; Rao, T. Subba [Department of Physics, Sri Krishnadevaraya University, Anantapur - 515 003, A.P (India)

    2014-01-28

    Cadmium telluride continues to be a leading candidate for the development of cost effective photovoltaics for terrestrial applications. In the present work two individual metallic targets of Cd and Te were used for the deposition of CdTe thin films on mica substrates from room temperature to 300 °C by DC reactive magnetron sputtering method. XRD patterns of CdTe thin films deposited on mica substrates exhibit peaks at 2? = 27.7°, 46.1° and 54.6°, which corresponds to reflection on (1 1 1), (2 2 0) and (3 1 1) planes of CdTe cubic structure. The intensities of XRD patterns increases with the increase of substrate temperature upto 150 °C and then it decreases at higher substrate temperatures. The conductivity of CdTe thin films measured from four probe method increases with the increase of substrate temperature. The activation energies (?E) are found to be decrease with the increase of substrate temperature. The optical transmittance spectra of CdTe thin films deposited on mica have a clear interference pattern in the longer wavelength region. The films have good transparency (T > 85 %) exhibiting interference pattern in the spectral region between 1200 – 2500 nm. The optical band gap of CdTe thin films are found to be in the range of 1.48 – 1.57. The refractive index, n decreases with the increase of wavelength, ?. The value of n and k increases with the increase of substrate temperature.

  19. Femtosecond laser ablation-based mass spectrometry. An ideal tool for stoichiometric analysis of thin films

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    LaHaye, Nicole L.; Kurian, Jose; Diwakar, Prasoon K.; Alff, Lambert; Harilal, Sivanandan S.

    2015-08-19

    An accurate and routinely available method for stoichiometric analysis of thin films is a desideratum of modern materials science where a material’s properties depend sensitively on elemental composition. We thoroughly investigated femtosecond laser ablation-inductively coupled plasma-mass spectrometry (fs-LA-ICP-MS) as an analytical technique for determination of the stoichiometry of thin films down to the nanometer scale. The use of femtosecond laser ablation allows for precise removal of material with high spatial and depth resolution that can be coupled to an ICP-MS to obtain elemental and isotopic information. We used molecular beam epitaxy-grown thin films of LaPd(x)Sb2 and T´-La2CuO4 to demonstrate themore »capacity of fs-LA-ICP-MS for stoichiometric analysis and the spatial and depth resolution of the technique. Here we demonstrate that the stoichiometric information of thin films with a thickness of ~10 nm or lower can be determined. Furthermore, our results indicate that fs-LA-ICP-MS provides precise information on the thin film-substrate interface and is able to detect the interdiffusion of cations.« less

  20. Method for producing textured substrates for thin-film photovoltaic cells

    DOE Patents [OSTI]

    Lauf, Robert J. (Oak Ridge, TN)

    1994-01-01

    The invention pertains to the production of ceramic substrates used in the manufacture of thin-film photovoltaic cells used for directly converting solar energy to electrical energy. Elongated ribbon-like sheets of substrate precursor containing a mixture of ceramic particulates, a binder, and a plasticizer are formed and then while green provided with a mechanically textured surface region used for supporting the thin film semiconductor of the photovoltaic cell when the sheets of the substrate precursor are subsequently cut into substrate-sized shapes and then sintered. The textured surface pattern on the substrate provides enhanced light trapping and collection for substantially increasing the solar energy conversion efficiency of thin-film photovoltaic cells.

  1. Method for producing textured substrates for thin-film photovoltaic cells

    DOE Patents [OSTI]

    Lauf, Robert J. (Oak Ridge, TN)

    1996-01-01

    The invention pertains to the production of ceramic substrates used in the manufacture of thin-film photovoltaic cells used for directly converting solar energy to electrical energy. Elongated ribbon-like sheets of substrate precursor containing a mixture of ceramic particulates, a binder, and a plasticizer are formed and then while green provided with a mechanically textured surface region used for supporting the thin film semiconductor of the photovoltaic cell when the sheets of the substrate precursor are subsequently cut into substrate-sized shapes and then sintered. The textured surface pattern on the substrate provides enhanced light trapping and collection for substantially increasing the, solar energy conversion efficiency of thin-film photovoltaic cells.

  2. Impact of strain on electronic defects in (Mg,Zn)O thin films

    SciTech Connect (OSTI)

    Schmidt, Florian Müller, Stefan; Wenckstern, Holger von; Benndorf, Gabriele; Pickenhain, Rainer; Grundmann, Marius

    2014-09-14

    We have investigated the impact of strain on the incorporation and the properties of extended and point defects in (Mg,Zn)O thin films by means of photoluminescence, X-ray diffraction, deep-level transient spectroscopy (DLTS), and deep-level optical spectroscopy. The recombination line Y?, previously detected in ZnO thin films grown on an Al-doped ZnO buffer layer and attributed to tensile strain, was exclusively found in (Mg,Zn)O samples being under tensile strain and is absent in relaxed or compressively strained thin films. Furthermore a structural defect E3´ can be detected via DLTS measurements and is only incorporated in tensile strained samples. Finally it is shown that the omnipresent deep-level E3 in ZnO can only be optically recharged in relaxed ZnO samples.

  3. Tunable electrical conductivity in oriented thin films of tetrathiafulvalene-based covalent organic framework

    SciTech Connect (OSTI)

    Cai, SL; Zhang, YB; Pun, AB; He, B; Yang, JH; Toma, FM; Sharp, ID; Yaghi, OM; Fan, J; Zheng, SR; Zhang, WG; Liu, Y

    2014-09-16

    Despite the high charge-carrier mobility in covalent organic frameworks (COFs), the low intrinsic conductivity and poor solution processability still impose a great challenge for their applications in flexible electronics. We report the growth of oriented thin films of a tetrathiafulvalene-based COF (TTF-COF) and its tunable doping. The porous structure of the crystalline TTF-COF thin film allows the diffusion of dopants such as I-2 and tetracyanoquinodimethane (TCNQ) for redox reactions, while the closely packed 2D grid sheets facilitate the cross-layer delocalization of thus-formed TTF radical cations to generate more conductive mixed-valence TTF species, as is verified by UV-vis-NIR and electron paramagnetic resonance spectra. Conductivity as high as 0.28 S m(-1) is observed for the doped COF thin films, which is three orders of magnitude higher than that of the pristine film and is among the highest for COF materials.

  4. Influence of hydrogen and hydrogen/methane plasmas on AlN thin films

    SciTech Connect (OSTI)

    Pobedinskas, P. Hardy, A.; Van Bael, M. K.; Haenen, K.; Degutis, G.; Dexters, W.

    2014-02-24

    Polycrystalline aluminum nitride (AlN) thin films are exposed to hydrogen and hydrogen/methane plasmas at different conditions. The latter plays an indispensable role in the subsequent deposition of nanocrystalline diamond thin films on AlN. The changes of AlN properties are investigated by means of Fourier transform infrared (FTIR) and Raman spectroscopies as well as atomic force microscopy. The E{sub 1}(TO) and E{sub 2}{sup 2} phonon mode frequencies blue-shift after the exposure to plasmas. The damping constant of E{sub 1}(TO) phonon, calculated from FTIR transmission spectra using the factorized model of a damped oscillator, and the width of E{sub 2}{sup 2} peak in Raman spectra decrease with increasing substrate temperature till the decomposition of AlN thin film becomes notable. It is proven that these changes are driven by the plasmas as annealing in vacuum does not induce them.

  5. Method for producing textured substrates for thin-film photovoltaic cells

    DOE Patents [OSTI]

    Lauf, R.J.

    1994-04-26

    The invention pertains to the production of ceramic substrates used in the manufacture of thin-film photovoltaic cells used for directly converting solar energy to electrical energy. Elongated ribbon-like sheets of substrate precursor containing a mixture of ceramic particulates, a binder, and a plasticizer are formed and then while green provided with a mechanically textured surface region used for supporting the thin film semiconductor of the photovoltaic cell when the sheets of the substrate precursor are subsequently cut into substrate-sized shapes and then sintered. The textured surface pattern on the substrate provides enhanced light trapping and collection for substantially increasing the solar energy conversion efficiency of thin-film photovoltaic cells. 4 figures.

  6. Method for producing textured substrates for thin-film photovoltaic cells

    DOE Patents [OSTI]

    Lauf, R.J.

    1996-04-02

    The invention pertains to the production of ceramic substrates used in the manufacture of thin-film photovoltaic cells used for directly converting solar energy to electrical energy. Elongated ribbon-like sheets of substrate precursor containing a mixture of ceramic particulates, a binder, and a plasticizer are formed and then while green provided with a mechanically textured surface region used for supporting the thin film semiconductor of the photovoltaic cell when the sheets of the substrate precursor are subsequently cut into substrate-sized shapes and then sintered. The textured surface pattern on the substrate provides enhanced light trapping and collection for substantially increasing the, solar energy conversion efficiency of thin-film photovoltaic cells. 4 figs.

  7. Flexible cadmium telluride thin films grown on electron-beam-irradiated graphene/thin glass substrates

    SciTech Connect (OSTI)

    Seo, Won-Oh; Kim, Jihyun, E-mail: hyunhyun7@korea.ac.kr [Department of Chemical and Biological Engineering, Korea University, Anam-dong, Sungbuk-gu, Seoul 136-713 (Korea, Republic of); Koo, Yong Hwan; Kim, Byungnam; Lee, Byung Cheol [Radiation Integrated System Research Division, Korea Atomic Energy Research Institute (KAERI), Daejeon 305-353 (Korea, Republic of); Kim, Donghwan [Department of Materials Science and Engineering, Korea University, Seoul 136-701 (Korea, Republic of)

    2014-08-25

    We demonstrate the close-spaced sublimation growth of polycrystalline cadmium telluride (CdTe) thin films on a flexible graphene electrode/thin glass substrate structure. Prior to the growth of CdTe films, chemical-vapor-deposited graphene was transferred onto a flexible glass substrate and subjected to electron-beam irradiation at an energy of 0.2?MeV in order to intentionally introduce the defects into it in a controlled manner. Micro-Raman spectroscopy and sheet resistance measurements were employed to monitor the damage and disorder in the electron-beam irradiated graphene layers. The morphology and optical properties of the CdTe thin films deposited on a graphene/flexible glass substrate were systematically characterized. The integration of the defective graphene layers with a flexible glass substrate can be a useful platform to grow various thin-film structures for flexible electronic and optoelectronic devices.

  8. Efficiency considerations for polycrystalline GaAs thin-film solar cells

    SciTech Connect (OSTI)

    Yamaguchi, M.; Itoh, Y.

    1986-07-01

    The effect of grain boundaries upon the efficiency of polycrystalline GaAs thin-film solar cells is analyzed. Solar-cell properties are calculated on a simple model where grain boundaries act as recombination centers to reduce the minority-carrier diffusion length in the solar cell's active layer and increase the space-charge layer recombination current. An effective diffusion length is expressed in terms of grain size, allowing the calculation of short-circuit current density and open-circuit voltage. Excellent agreement is obtained between theory and experiment. The fabrication of thin-film GaAs solar cells with an efficiency greater than 18% appears to be possible if the grain size in the thin-film GaAs layer with thickness of 3 ..mu..m is larger than 1000 ..mu..m.

  9. Engineering Gilbert damping by dilute Gd doping in soft magnetic Fe thin films

    SciTech Connect (OSTI)

    Zhang, W. Jiang, S.; Sun, L.; Wang, Y. K.; Zhai, Y.; Wong, P. K. J.; Wang, K.; Jong, M. P. de; Wiel, W. G. van der; Laan, G. van der

    2014-05-07

    By analyzing the ferromagnetic resonance linewidth, we show that the Gilbert damping constant in soft magnetic Fe thin films can be enhanced by ?6 times with Gd doping of up to 20%. At the same time, the magnetic easy axis remains in the film plane while the coercivity is strongly reduced after Gd inclusion. X-ray magnetic circular dichroism measurements reveal a strong increase in the orbital-to-spin moment ratio of Fe with increasing Gd concentration, in full agreement with the increase in the Gilbert damping obtained for these thin films. Combined with x-ray diffraction and vibrating sample magnetometry, the results demonstrate that the FeGd thin films with dilute Gd doping of up to 20% are promising candidates for spin-transfer-torque applications in soft magnetic devices, in which an enhanced damping is required.

  10. Modulated IR radiometry for determining thermal properties and basic characteristics of titanium thin films

    SciTech Connect (OSTI)

    Apreutesei, Mihai; Lopes, Claudia; Vaz, Filipe; Macedo, Francisco; Borges, Joel

    2014-07-01

    Titanium thin films of different thicknesses were prepared by direct current magnetron sputtering to study modulated infrared (IR) radiometry as a tool for analyzing film thickness. Thickness was varied by regularly increasing the deposition time, keeping all the other deposition parameters constant. The influence of film thickness on morphological, structural, and electrical properties of the titanium coatings also was investigated. The experimental results revealed a systematic grain growth with increasing film thickness, along with enhanced film crystallinity, which led to increased electrical conductivity. Using the results obtained by modulated IR radiometry, the thickness of each thin film was calculated. These thickness values were then compared with the coating thickness measurements obtained by scanning electron microscopy. The values confirmed the reliability of modulated IR radiometry as an analysis tool for thin films and coatings, and for determining thicknesses in the micrometer range, in particular.

  11. Molybdenum as a contact material in zinc tin oxide thin film transistors

    SciTech Connect (OSTI)

    Hu, W.; Peterson, R. L., E-mail: blpeters@umich.edu [Department of Electrical Engineering and Computer Science, University of Michigan, Ann Arbor, Michigan 48109-2122 (United States)

    2014-05-12

    Amorphous oxide semiconductors are of increasing interest for a variety of thin film electronics applications. Here, the contact properties of different source/drain electrode materials to solution-processed amorphous zinc tin oxide (ZTO) thin-film transistors are studied using the transmission line method. The width-normalized contact resistance between ZTO and sputtered molybdenum is measured to be 8.7 ?-cm, which is 10, 20, and 600 times smaller than that of gold/titanium, indium tin oxide, and evaporated molybdenum electrodes, respectively. The superior contact formed using sputtered molybdenum is due to a favorable work function lineup, an insulator-free interface, bombardment of ZTO during molybdenum sputtering, and trap-assisted tunneling. The transfer length of the sputtered molybdenum/ZTO contact is 0.34??m, opening the door to future radio-frequency sub-micron molybdenum/ZTO thin film transistors.

  12. Numerical study of The Remittances of Axially Excited Chiral Sculptured Zirconia Thin Films

    E-Print Network [OSTI]

    Babaei, Ferydon; 10.1080/09500340701836997

    2009-01-01

    The transmission and reflection spectra from a right-handed chiral sculptured zirconia thin film are calculated using the coupled wave theory and the Bruggeman homogenization formalism in conjunction with the experimental data for the relative dielectric constant of zirconia thin film. The dielectric dispersion function effect on these spectra appeared in wavelengths shorter than the Bragg wavelength. In wavelengths larger than the Bragg wavelength, the dispersion of the dielectric function can be ignored. The results achieved in this work are consistent with the experimental data (Wu et al. (2000)). A shift towards shorter wavelengths is observed for the Bragg peak with increasing the void fraction, which is in agreement with the theoretical work of Lakhtakia (2000). Sorge et al. (2006) also found this effect in their experimental results on TiO2 chiral thin films, while they also found that unlike our results the intensity of the reflectance of the Bragg peak decreases with increasing the void fraction. Thi...

  13. Evaporation system and method for gas jet deposition of thin film materials

    DOE Patents [OSTI]

    Schmitt, Jerome J. (New Haven, CT); Halpern, Bret L. (Bethany, CT)

    1994-01-01

    A method and apparatus for depositing thin films of materials such as metals, oxides and nitrides at low temperature relies on a supersonic free jet of inert carrier gas to transport vapor species generated from an evaporation source to the surface of a substrate. Film deposition vapors are generated from solid film precursor materials, including those in the form of wires or powders. The vapor from these sources is carried downstream in a low pressure supersonic jet of inert gas to the surface of a substrate where the vapors deposit to form a thin film. A reactant gas can be introduced into the gas jet to form a reaction product with the evaporated material. The substrate can be moved from the gas jet past a gas jet containing a reactant gas in which a discharge has been generated, the speed of movement being sufficient to form a thin film which is chemically composed of the evaporated material and reactant gases.

  14. Enhanced Efficiency of Light-Trapping Nanoantenna Arrays for Thin Film Solar Cells

    E-Print Network [OSTI]

    Simovski, Constantin R; Voroshilov, Pavel M; Guzhva, Michael E; Belov, Pavel A; Kivshar, Yuri S

    2013-01-01

    We suggest a novel concept of efficient light-trapping structures for thin-film solar cells based on arrays of planar nanoantennas operating far from plasmonic resonances. The operation principle of our structures relies on the excitation of chessboard-like collective modes of the nanoantenna arrays with the field localized between the neighboring metal elements. We demonstrated theoretically substantial enhancement of solar-cell short-circuit current by the designed light-trapping structure in the whole spectrum range of the solar-cell operation compared to conventional structures employing anti-reflecting coating. Our approach provides a general background for a design of different types of efficient broadband light-trapping structures for thin-film solar-cell technologically compatible with large-area thin-film fabrication techniques.

  15. Micropatterned lead zirconium titanate thin films J.S. Vartulia)

    E-Print Network [OSTI]

    Aksay, Ilhan A.

    was trapezoidlike. Single perovskite PZT grains that formed during annealing at 600­700 °C completely filled isopropoxide were used as the starting materials. Substrates used included silver tape, stainless steel plate

  16. Deposition and characterization of molybdenum thin films using dc-plasma magnetron sputtering

    SciTech Connect (OSTI)

    Khan, Majid, E-mail: majids@hotmail.com [National University of Sciences and Technology, School of Chemical and Materials Engineering (Pakistan); Islam, Mohammad, E-mail: mohammad.islam@gmail.com [King Saud University, Center of Excellence for Research in Engineering Materials, Advanced Manufacturing Institute (Saudi Arabia)

    2013-12-15

    Molebdenum (Mo) thin films were deposited on well-cleaned soda-lime glass substrates using DC-plasma magnetron sputtering. In the design of experiment deposition was optimized for maximum beneficial characteristics by monitoring effect of process variables such as deposition power (100–200 W). Their electrical, structural and morphological properties were analyzed to study the effect of these variables. The electrical resistivity of Mo thin films could be reduced by increasing deposition power. Within the range of analyzed deposition power, Mo thin films showed a mono crystalline nature and the crystallites were found to have an orientation along [110] direction. The surface morphology of thin films showed that a highly dense micro structure has been obtained. The surface roughness of films increased with deposition power. The adhesion of Mo thin films could be improved by increasing the deposition power. Atomic force microscopy was used for the topographical study of the films and to determine the roughness of the films. X-ray diffractrometer and scanning electron microscopy analysis were used to investigate the crystallinity and surface morphology of the films. Hall effect measurement system was used to find resistivity, carrier mobility and carrier density of deposited films. The adhesion test was performed using scotch hatch tape adhesion test. Mo thin films prepared at deposition power of 200 W, substrate temperature of 23°C and Ar pressure of 0.0123 mbar exhibited a mono crystalline structure with an orientation along (110) direction, thickness of ?550 nm and electrical resistivity value of 0.57 × 10{sup ?4} ? cm.

  17. PHOTOCATALYTIC GENERATION OF DISSOLVED OXYGEN AND OXYHEMOGLOBIN IN WHOLE BLOOD BASED ON THE INDIRECT INTERACTION OF UV LIGHT WITH A SEMICONDUCTING TITANIUM DIOXIDE THIN FILM

    SciTech Connect (OSTI)

    Gilbert, Richard J.; Carleton, Linda M.; Dasse, Kurt A.; Martin, Peter M.; Williford, Rick E.; Monzyk, Bruce F.

    2007-10-01

    Most current artificial lung technologies require the delivery of oxygen to the blood via permeable hollow fibers, depending on membrane diffusivity and differential partial pressure to drive gas exchange. We have identified an alternative approach in which dissolved oxygen (DO) is generated directly from the water content of blood through the indirect interaction of UV light with a semi-conducting titanium dioxide thin film. This reaction is promoted by photon absorption and displacement of electrons from the photoactive film, and yields a cascading displacement of electron “holes” to the aqueous interface resulting in the oxidation of water molecules to form DO. Anatase TiO2 (photocatalyst) and ITO (electrically conductive and light transparent) coatings were deposited onto quartz flow-cell plates by DC reactive magnetron sputtering. The crystal structure of the films was evaluated by grazing incidence X-Ray Diffraction (GIXRD), which confirmed that the primary crystal phase of the TiO2 thin film was anatase with a probable rutile secondary phase. Surface topology and roughness were determined by atomic force microscopy, demonstrating a stochastically uniform array of nanocrystallites. UV illumination of the titanium dioxide thin film through the quartz/ITO surface resulted in the rapid increase of DO and oxyhemoglobin in adjacent flowing blood on the opposite TiO2 surface at a rate of 1.28 x 10-5 mmol O2/sec. The rate of oxyhemoglobin generation was linearly proportional to residence time adjacent to the photoactive surface in a flow-through test cell under steady-state conditions. Preliminary biocompatibility for the proposed photocatalytic effect on whole blood demonstrated no increase in the rate of hemolysis or generation of toxic byproducts of photo-oxidation. These results demonstrate the feasibility and safety of employing optoelectronic mechanisms to promote oxygenation of hemoglobin in whole blood, and provide substantiation for the use of this technology as a mechanism for artificial respiratory support.

  18. Influence of sputtering power on the optical properties of ITO thin films

    SciTech Connect (OSTI)

    K, Aijo John; M, Deepak, E-mail: manju.thankamoni@gmail.com; T, Manju, E-mail: manju.thankamoni@gmail.com [Department of Physics, Sree Sankara College, Kalady P. O., Ernakulam Dist., Kerala (India); Kumar, Vineetha V. [Dept. of Physics, K. E. College, Mannanam, Kottayam Dist., Kerala (India)

    2014-10-15

    Tin doped indium oxide films are widely used in transparent conducting coatings such as flat panel displays, crystal displays and in optical devices such as solar cells and organic light emitting diodes due to the high electrical resistivity and optical transparency in the visible region of solar spectrum. The deposition parameters have a commendable influence on the optical and electrical properties of the thin films. In this study, ITO thin films were prepared by RF magnetron sputtering. The properties of the films prepared under varying sputtering power were compared using UV- visible spectrophotometry. Effect of sputtering power on the energy band gap, absorption coefficient and refractive index are investigated.

  19. Method of preparing high-temperature-stable thin-film resistors

    DOE Patents [OSTI]

    Raymond, L.S.

    1980-11-12

    A chemical vapor deposition method for manufacturing tungsten-silicide thin-film resistors of predetermined bulk resistivity and temperature coefficient of resistance (TCR) is disclosed. Gaseous compounds of tungsten and silicon are decomposed on a hot substrate to deposit a thin-film of tungsten-silicide. The TCR of the film is determined by the crystallinity of the grain structure, which is controlled by the temperature of deposition and the tungsten to silicon ratio. The bulk resistivity is determined by the tungsten to silicon ratio. Manipulation of the fabrication parameters allows for sensitive control of the properties of the resistor.

  20. Synthesis and characterization of SnO{sub 2} thin films doped with Fe to 10%

    SciTech Connect (OSTI)

    López, E.; Marín, J.; Osorio, J.

    2014-05-15

    Appropriate conditions for SnO{sub 2} powder synthesis doped with iron to 10% by using sol-gel route are found. The powders obtained have been analyzed by means of analytic spectroscopic techniques: Raman, Mössbauer, diffuse reflectance, Fourier transform infrared, and X-ray diffraction. Sn{sub 0.9}Fe{sub 0.1}O{sub 2} thin films deposited by AC magnetron sputtering on silicon substrates are obtained and characterized. A crystal structure rutile-type was found for thin films.

  1. Structural and optical studies on AgSbSe{sub 2} thin films

    SciTech Connect (OSTI)

    Asokan, T. Namitha; Urmila, K. S.; Pradeep, B. [Solid State Physics Laboratory, Department of Physics, Cochin University of Science and Technology, Kochi- 22, Kerala (India)

    2014-01-28

    AgSbSe{sub 2} semiconducting thin films are successfully deposited using reactive evaporation technique at a substrate temperature of 398K. X-ray diffraction studies reveal that the films are polycrystalline in nature. The structural parameters such as average particle size, dislocation density, and number of crystallites per unit have been evaluated. Atomic Force Microscopy is used to study the topographic characteristics of the film including the grain size and surface roughness. The silver antimony selenide thin films have high absorption coefficient of about 10{sup 5} cm{sup ?1} and it has an indirect band gap of 0.64eV.

  2. Process for forming epitaxial perovskite thin film layers using halide precursors

    DOE Patents [OSTI]

    Clem, Paul G. (Albuquerque, NM); Rodriguez, Mark A. (Albuquerque, NM); Voigt, James A. (Corrales, NM); Ashley, Carol S. (Albuquerque, NM)

    2001-01-01

    A process for forming an epitaxial perovskite-phase thin film on a substrate. This thin film can act as a buffer layer between a Ni substrate and a YBa.sub.2 Cu.sub.3 O.sub.7-x superconductor layer. The process utilizes alkali or alkaline metal acetates dissolved in halogenated organic acid along with titanium isopropoxide to dip or spin-coat the substrate which is then heated to about 700.degree. C. in an inert gas atmosphere to form the epitaxial film on the substrate. The YBCO superconductor can then be deposited on the layer formed by this invention.

  3. Young's modulus of electroplated Ni thin film for MEMS applications J.K. Luoa,*, A.J. Flewitta

    E-Print Network [OSTI]

    Fleck, Norman A.

    to a less dense coating. D 2004 Elsevier B.V. All rights reserved. Keywords: Young's modulus; ElectroplatedYoung's modulus of electroplated Ni thin film for MEMS applications J.K. Luoa,*, A.J. Flewitta , S online 28 April 2004 Abstract The Young's modulus of an electroplated nickel (Ni) thin film suitable

  4. Effects of residual stress on the thin-film elastic moduli calculated from surface acoustic wave spectroscopy experimentsB

    E-Print Network [OSTI]

    Effects of residual stress on the thin-film elastic moduli calculated from surface acoustic wave stress affects the values of thin-film elastic moduli determined from surface acoustic wave spectroscopy surface acoustic wave measurements may be analyzed to obtain additional information about the mechanical

  5. Effect of varying material anisotropy on critical current anistropy in vicinal YBa2Cu3O7-delta thin films

    E-Print Network [OSTI]

    Durrell, John H; Roessler, Roman; Delmare, Marie-Pierre; Pedarnig, Johannes; Baeuerle, Dieter; Evetts, Jan E

    2003-01-01

    on fully oxygenated and de-oxygenated YBa$_2$Cu$_3$O$_{7-\\delta}$ thin films and optimally oxygenated Y$_{0.75}$Ca$_{0.2}$Ba$_2$Cu$_3$O$_{7-\\delta}$ thin films. The films were grown on 10$^{\\circ}$ mis-cut SrTiO$_3$ substrates to enable the intrinsic vortex...

  6. Electron energy-loss spectroscopy of boron-doped layers in amorphous thin film silicon solar cells

    E-Print Network [OSTI]

    Dunin-Borkowski, Rafal E.

    Electron energy-loss spectroscopy of boron-doped layers in amorphous thin film silicon solar cells. de Bariloche, Argentina 3 ECN Solar Energy, High Tech Campus, Building 5, 5656 AE Eindhoven energy-loss spectroscopy (EELS) is used to study p-doped layers in n-i-p amorphous thin film Si solar

  7. The Roles of Cu Impurity States in CdTe Thin Film Solar Cells Ken K. Chin1

    E-Print Network [OSTI]

    as commercially successful, second generation thin film photovoltaic (PV) products, at a production cost of $0 PV technologies, such as Cu(In,Ga)Se2 (CIGS), which has a lower theoretical limit ~26% but a higher involves Cu impurities. The CdTe thin film uses low cost 5N tellurium, which, either as a byproduct

  8. Effect of Shunts on Thin-Film CdTe Module Performance. Galymzhan T. Koishiyev, James R. Sites

    E-Print Network [OSTI]

    Sites, James R.

    -film module. A numerical estimate of module-efficiency loss in the worst-case scenario due to shunts-film modules have now been on the market for more than two decades, and the minimization of loss mechanisms design and geometry of most thin- film modules is essentially the same. A typical thin-film module

  9. June 1983 / Vol. 8, No. 6 / OPTICS LETTERS 295 Coherent anti-Stokes Raman scattering in thin-film dielectric

    E-Print Network [OSTI]

    Sipe,J. E.

    June 1983 / Vol. 8, No. 6 / OPTICS LETTERS 295 Coherent anti-Stokes Raman scattering in thin-film analyze coherent anti-Stokes Raman scattering in thin-film dielectric waveguides. Extraordinarily large enhancements can be obtained in films and at surfaces by coupling externally incident radiation fields to local

  10. Atomic layer deposition of Zn(O,S) thin films with tunable electrical properties by oxygen annealing

    E-Print Network [OSTI]

    properties to further improve the performance of thin-film solar cells using earth- abundant and non) is one of the most reliable materials used in thin-film solar cells, but currently the most efficient CIGS-based solar cells use CdS,1,2 a toxic material, as an n-type buffer layer between the p-type CIGS

  11. HIGH EFFICIENCY CdTe/CdS THIN FILM SOLAR CELLS WITH A NOVEL BACK-CONTACT Nicola Romeoa

    E-Print Network [OSTI]

    Romeo, Alessandro

    HIGH EFFICIENCY CdTe/CdS THIN FILM SOLAR CELLS WITH A NOVEL BACK-CONTACT Nicola Romeoa , Alessio in the fabrication of high efficiency CdTe/CdS thin film solar cells. Usually, it is done first by etching the CdTe/CdS structure causing shunt paths by segregating into the grain boundaries or lowering the cell efficiency

  12. Rapid Deposition Technology Holds the Key for the World's Largest Manufacturer of Thin-Film Solar Modules (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2013-08-01

    First Solar, Inc. has been collaborating with NREL since 1991, advancing its thin-film cadmium telluride solar technology to grow from a startup company to become one of the world's largest manufacturers of solar modules, and the world's largest manufacturer of thin-film solar modules.

  13. Towards high efficiency thin-film crystalline silicon solar cells: The roles of light trapping and non-radiative recombinations

    E-Print Network [OSTI]

    important evaluation criterion for photovoltaic (PV) technology. Therefore, research on novel structuresTowards high efficiency thin-film crystalline silicon solar cells: The roles of light trapping February 2014; published online 3 March 2014) Thin-film solar cells based on silicon have emerged

  14. Anode-supported thin-film fuel cells operated in a single chamber configuration 2T-I-12

    E-Print Network [OSTI]

    Haile, Sossina M.

    on the anode, producing a complex response in fuel cell power output. Under optimized gas compositions and flowAnode-supported thin-film fuel cells operated in a single chamber configuration 2T-I-12 Zongping of anode-supported, thin-film, single chamber fuel cells (SCFCs) have been investigated. Cells, in which Ni

  15. Probing the adhesion of submicron thin films fabricated on a polymer substrate via nano-transfer printing

    E-Print Network [OSTI]

    Li, Teng

    Probing the adhesion of submicron thin films fabricated on a polymer substrate via nano- transfer.1088/0960-1317/22/9/095002 Probing the adhesion of submicron thin films fabricated on a polymer substrate via nano-transfer printing/095002 Abstract Determining the interfacial adhesion of ultrathin functional films in micro

  16. Sputtered Molybdenum Bilayer Back Contact for Copper Indium Diselenide-Based Polycrystalline Thin-Film Solar Cells

    E-Print Network [OSTI]

    Scofield, John H.

    -of-the-art polycrystalline copper indium gallium diselenide solar cells with good results. Thin Solid Films, 260 (1), pp. 26), have emerged as promising polycrystalline thin-film semiconductors for solar cell absorber layers.2 polycrystalline thin-film photovoltaic (PV) technology. 3 Solar cells fabricated at the National Renewable Energy

  17. Electrochromic Behavior in Flexible WO3 and Prussian Blue Thin Films for Use in Ski Goggle Lenses

    E-Print Network [OSTI]

    Sparks, Taylor D.

    Electrochromic Behavior in Flexible WO3 and Prussian Blue Thin Films for Use in Ski Goggle Lenses electrodeposited Prussian blue (PB) and sputtered WO3 thin films on ITO coated PET substrates 3. Films were to intercalate with the crystal structure of the electrochromic layer. This reaction for WO3 is as follows: WO3

  18. An analysis of the x-ray linear dichroism spectrum for NiO thin films grown on vicinal Ag(001)

    E-Print Network [OSTI]

    Wu, Y.Z.

    2008-01-01

    dichroism spectrum for NiO thin films grown on vicinal Ag(Antiferromagnetic (AFM) NiO thin films are grown epitaxiallyXLD). We find that the NiO AFM spin exhibits an in- plane

  19. Magneto-optical characterizations of FeTe???Se??? thin films with critical current density over 1 MA/cm²

    SciTech Connect (OSTI)

    Sun, Yue; Li, Qiang; Tsuchiya, Yuji; Pyon, Sunseng; Tamegai, Tsuyoshi; Zhang, Cheng; Ozaki, Toshinori

    2015-01-01

    We performed magneto-optical (MO) measurements on FeTe???Se??? thin films grown on LaAlO? (LAO) and Yttria-stabilized zirconia (YSZ) single-crystalline substrates. These thin films show superconducting transition temperature Tc ~19 K, 4 K higher than the bulk sample. Typical roof-top patterns can be observed in the MO images of thin films grown on LAO and YSZ, from which a large and homogeneous critical current density Jc ~ 3 - 4 x 10? A/cm² at 5 K was obtained. Magnetic flux penetration measurement reveals that the current is almost isotropically distributed in the two thin films. Compared with bulk crystals, FeTe???Se??? thin film demonstrates not only higher Tc, but also much larger Jc, which is attractive for applications.

  20. Magneto-optical characterizations of FeTe???Se??? thin films with critical current density over 1 MA/cm²

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Sun, Yue; Li, Qiang; Tsuchiya, Yuji; Pyon, Sunseng; Tamegai, Tsuyoshi; Zhang, Cheng; Ozaki, Toshinori

    2014-12-03

    We performed magneto-optical (MO) measurements on FeTe???Se??? thin films grown on LaAlO? (LAO) and Yttria-stabilized zirconia (YSZ) single-crystalline substrates. These thin films show superconducting transition temperature Tc ~19 K, 4 K higher than the bulk sample. Typical roof-top patterns can be observed in the MO images of thin films grown on LAO and YSZ, from which a large and homogeneous critical current density Jc ~ 3 - 4 x 10? A/cm² at 5 K was obtained. In this study, magnetic flux penetration measurement reveals that the current is almost isotropically distributed in the two thin films. Compared with bulk crystals,more »FeTe???Se??? thin film demonstrates not only higher Tc, but also much larger Jc, which is attractive for applications.« less

  1. Thin Film Materials and Processing Techniques for a Next Generation Photovoltaic Device: Cooperative Research and Development Final Report, CRADA Number CRD-12-470

    SciTech Connect (OSTI)

    van Hest, M.

    2013-08-01

    This research extends thin film materials and processes relevant to the development and production of a next generation photovoltaic device.

  2. Light trapping and electrical transport in thin-film solar cells with randomly rough Piotr Kowalczewski, Angelo Bozzola, Marco Liscidini, and Lucio Claudio Andreani

    E-Print Network [OSTI]

    Light trapping and electrical transport in thin-film solar cells with randomly rough textures Piotr solar cells J. Appl. Phys. 105, 094511 (2009); 10.1063/1.3108689 Local versus global absorption in thin-film in thin-film solar cells with randomly rough textures Piotr Kowalczewski,a) Angelo Bozzola, Marco

  3. Response to "Comment on `Towards high efficiency thin-film crystalline silicon solar cells: The roles of light trapping and non-radiative recombinations'" [J. Appl. Phys. 117,

    E-Print Network [OSTI]

    Response to "Comment on `Towards high efficiency thin-film crystalline silicon solar cells high efficiency thin-film crystalline silicon solar cells: The roles of light trapping and non.1063/1.4905182 Towards high efficiency thin-film crystalline silicon solar cells: The roles of light trapping and non

  4. Bandgap-Graded Cu2Zn(Sn1-xGex)S4 Thin-Film Solar Cells Derived from Metal Chalcogenide Complex Ligand Capped Nanocrystals

    E-Print Network [OSTI]

    Cao, Guozhong

    Bandgap-Graded Cu2Zn(Sn1-xGex)S4 Thin-Film Solar Cells Derived from Metal Chalcogenide ComplexS) thin-film solar cells based on metal chalcogenide complex (MCC) ligand capped nanocrystals (NCs attention as a promising absorber material in thin film-solar cells due to its abundance and nontoxicity

  5. DISORDER ENGINEERING FOR LIGHT-TRAPPING IN THIN-FILM SOLAR CELLS P. Kowalczewski, M. Liscidini, and L.C. Andreani

    E-Print Network [OSTI]

    DISORDER ENGINEERING FOR LIGHT-TRAPPING IN THIN-FILM SOLAR CELLS P. Kowalczewski, M. Liscidini: In this work we focus on randomly rough textures for light-trapping in thin-film silicon solar cells. We use light management is a key to achieve high efficiency thin-film solar cells, and a wide variety of light

  6. Size effects on the onset of plastic deformation during nanoindentation of thin films and patterned lines

    E-Print Network [OSTI]

    Van Vliet, Krystyn J.

    Size effects on the onset of plastic deformation during nanoindentation of thin films and patterned; accepted 13 August 2003 Plastic deformation of materials exhibits a strong size dependence when, particularly the transition from elastic to plastic deformation and the early stages of plastic deformation. We

  7. Design, fabrication, packaging and testing of thin film thermocouples for boiling studies 

    E-Print Network [OSTI]

    Sinha, Nipun

    2009-06-02

    Used for Both The Layers of Photolithography ............ ................................................................... 38 2.21 Reactive Ion Etcher Used for Oxygen Plasma Cleaning................... 40 2.22 Metal Evaporator Used... .................................................. 56 3.3 Picture of the Wedge, Spool and Sample Holder for the Wire Bonding Apparatus............ ................................................................ 59 3.4 Two Methods of Resistance Arc Welding for Thin Film Thermocouples...

  8. Investigation of defects in In–Ga–Zn oxide thin film using electron spin resonance signals

    SciTech Connect (OSTI)

    Nonaka, Yusuke; Kurosawa, Yoichi; Komatsu, Yoshihiro; Ishihara, Noritaka; Oota, Masashi; Nakashima, Motoki; Hirohashi, Takuya; Takahashi, Masahiro; Yamazaki, Shunpei; Obonai, Toshimitsu; Hosaka, Yasuharu; Koezuka, Junichi; Yamauchi, Jun

    2014-04-28

    In–Ga–Zn oxide (IGZO) is a next-generation semiconductor material seen as an alternative to silicon. Despite the importance of the controllability of characteristics and the reliability of devices, defects in IGZO have not been fully understood. We investigated defects in IGZO thin films using electron spin resonance (ESR) spectroscopy. In as-sputtered IGZO thin films, we observed an ESR signal which had a g-value of g?=?2.010, and the signal was found to disappear under thermal treatment. Annealing in a reductive atmosphere, such as N{sub 2} atmosphere, generated an ESR signal with g?=?1.932 in IGZO thin films. The temperature dependence of the latter signal suggests that the signal is induced by delocalized unpaired electrons (i.e., conduction electrons). In fact, a comparison between the conductivity and ESR signal intensity revealed that the signal's intensity is related to the number of conduction electrons in the IGZO thin film. The signal's intensity did not increase with oxygen vacancy alone but also with increases in both oxygen vacancy and hydrogen concentration. In addition, first-principle calculation suggests that the conduction electrons in IGZO may be generated by defects that occur when hydrogen atoms are inserted into oxygen vacancies.

  9. Orogenic movement mechanism for the formation of symmetrical relief features in copper nitride thin films

    E-Print Network [OSTI]

    Zexian, Cao

    Orogenic movement mechanism for the formation of symmetrical relief features in copper nitride thin heterogeneity, etc. In preparing thin films of the thermally unstable copper nitride Cu3N, growth proceeds-gap semiconduc- tors such as SiC and GaN that are expected to operate at temperatures over 300 °C demand both

  10. Determination of pore-size distribution in low-dielectric thin films D. W. Gidleya)

    E-Print Network [OSTI]

    Gidley, David

    -size distribution on pore shape/dimensionality and sample temperature is predicted using a simple quantum mechanicalDetermination of pore-size distribution in low-dielectric thin films D. W. Gidleya) and W. E. Frieze Department of Physics, University of Michigan, Ann Arbor, Michigan 48109 T. L. Dull, J. Sun, and A

  11. SUPERCONDUCTING PROPERTIES OF ALUMINIUM THIN FILMS AFTER ION IMPLANTATION AT LIQUID HELIUM TEMPERATURES (*)

    E-Print Network [OSTI]

    Boyer, Edmond

    L-271 SUPERCONDUCTING PROPERTIES OF ALUMINIUM THIN FILMS AFTER ION IMPLANTATION AT LIQUID HELIUM concentration near AlH2. It is well-known [1] that the superconducting transition temperature Tc of metals as in the electronic density of states N(O) at the Fermi surface. In the case of weak-coupling superconductors

  12. Epitaxial ternary nitride thin films prepared by a chemical solution method

    SciTech Connect (OSTI)

    Luo, Hongmei [Los Alamos National Laboratory; Feldmann, David M [Los Alamos National Laboratory; Wang, Haiyan [TEXAS A& M; Bi, Zhenxing [TEXAS A& M

    2008-01-01

    It is indispensable to use thin films for many technological applications. This is the first report of epitaxial growth of ternary nitride AMN2 films. Epitaxial tetragonal SrTiN2 films have been successfully prepared by a chemical solution approach, polymer-assisted deposition. The structural, electrical, and optical properties of the films are also investigated.

  13. Method and apparatus for increasing the durability and yield of thin film photovoltaic devices

    DOE Patents [OSTI]

    Phillips, James E. (Newark, DE); Lasswell, Patrick G. (Newark, DE)

    1987-01-01

    Thin film photovoltaic cells having a pair of semiconductor layers between an opaque and a transparent electrical contact are manufactured in a method which includes the step of scanning one of the semiconductor layers to determine the location of any possible shorting defect. Upon the detection of such defect, the defect is eliminated to increase the durability and yield of the photovoltaic device.

  14. Stabilizing Graphitic Thin Films of Wurtzite Materials by Epitaxial Strain Dangxin Wu,1

    E-Print Network [OSTI]

    Simons, Jack

    numbers: 81.15.Aa, 64.70.Nd, 68.35.BÀ, 73.20.At Modern materials growth and synthesis technology have allowed the creation of materials that do not exist in nature. Epitaxial growth of thin films, one such technology, creates novel materials by employing two mechanisms: (1) grow thermodynamically metastable thin

  15. Low emissivity high-temperature tantalum thin film coatings for silicon Veronika Rinnerbauer,a)

    E-Print Network [OSTI]

    Low emissivity high-temperature tantalum thin film coatings for silicon devices Veronika) The authors study the use of thin ($230 nm) tantalum (Ta) layers on silicon (Si) as a low emissivity (high to achieve such a coating are low emissivity in the near infrared and superior thermal stability at high

  16. Beta (?) tungsten thin films: Structure, electron transport, and giant spin Hall effect

    SciTech Connect (OSTI)

    Hao, Qiang; Chen, Wenzhe; Xiao, Gang

    2015-05-04

    We use a simple magnetron sputtering process to fabricate beta (?) tungsten thin films, which are capable of generating giant spin Hall effect. As-deposited thin films are always in the metastable ?-W phase from 3.0 to 26.7?nm. The ?-W phase remains intact below a critical thickness of 22.1?nm even after magnetic thermal annealing at 280?°C, which is required to induce perpendicular magnetic anisotropy (PMA) in a layered structure of ?-W/Co{sub 40}Fe{sub 40}B{sub 20}/MgO. Intensive annealing transforms the thicker films (>22.1?nm) into the stable ?-W phase. We analyze the structure and grain size of both ?- and ?-W thin films. Electron transport in terms of resistivity and normal Hall effect is studied over a broad temperature range of 10?K to at least 300?K on all samples. Very low switching current densities are achieved in ?-W/Co{sub 40}Fe{sub 40}B{sub 20}/MgO with PMA. These basic properties reveal useful behaviors in ?-W thin films, making them technologically promising for spintronic magnetic random access memories and spin-logic devices.

  17. Time-Resolved Magnetic Flux and AC-Current Distributions in Superconducting YBCO Thin Films and

    E-Print Network [OSTI]

    Shaw, Leah B.

    Time-Resolved Magnetic Flux and AC-Current Distributions in Superconducting YBCO Thin Films on superconductors. The high time and spatial resolutions of the measurements also offer good quantitative data analysis of the MO images. Y Ba2Cu3O7-8 (YBCO) was discovered as a high-temperature superconductor (HTSC

  18. Angular behavior of the absorption limit in thin film silicon solar cells

    E-Print Network [OSTI]

    Naqavi, Ali; Söderström, Karin; Battaglia, Corsin; Paeder, Vincent; Scharf, Toralf; Herzig, Hans Peter; Ballif, Christophe

    2013-01-01

    We investigate the angular behavior of the upper bound of absorption provided by the guided modes in thin film solar cells. We show that the 4n^2 limit can be potentially exceeded in a wide angular and wavelength range using two-dimensional periodic thin film structures. Two models are used to estimate the absorption enhancement; in the first one, we apply the periodicity condition along the thickness of the thin film structure but in the second one, we consider imperfect confinement of the wave to the device. To extract the guided modes, we use an automatized procedure which is established in this work. Through examples, we show that from the optical point of view, thin film structures have a high potential to be improved by changing their shape. Also, we discuss the nature of different optical resonances which can be potentially used to enhance light trapping in the solar cell. We investigate the two different polarization directions for one-dimensional gratings and we show that the transverse magnetic pola...

  19. Diffusion of indium and gallium in Cu(In,Ga)Se2 thin film solar cells

    E-Print Network [OSTI]

    Rockett, Angus

    Diffusion of indium and gallium in Cu(In,Ga)Se2 thin film solar cells O. Lundberga,*, J. Lua , A conversion efficiency of solar cells made from this material [1]. One of the special qualities of the CIGS improve the solar cell performance. In many of the different CIGS fabrication techniques, an in depth

  20. Homogeneous, dual layer, solid state, thin film deposition for structural and/or electrochemical characteristics

    DOE Patents [OSTI]

    Pitts, J. Roland; Lee, Se-Hee; Tracy, C. Edwin; Li, Wenming

    2014-04-08

    Solid state, thin film, electrochemical devices (10) and methods of making the same are disclosed. An exemplary device 10 includes at least one electrode (14) and an electrolyte (16) deposited on the electrode (14). The electrolyte (16) includes at least two homogenous layers of discrete physical properties. The two homogenous layers comprise a first dense layer (15) and a second porous layer (16).

  1. Optically activated sub-millimeter dielectric relaxation in amorphous thin film silicon at room temperature

    SciTech Connect (OSTI)

    Rahman, Rezwanur; Ohno, Tim R.; Taylor, P. C.; Scales, John A.

    2014-05-05

    Knowing the frequency-dependent photo-induced complex conductivity of thin films is useful in the design of photovoltaics and other semi-conductor devices. For example, annealing in the far-infrared could in principle be tailored to the specific dielectric properties of a particular sample. The frequency dependence of the conductivity (whether dark or photo-induced) also gives insight into the effective dimensionality of thin films (via the phonon density of states) as well as the presence (or absence) of free carriers, dopants, defects, etc. Ultimately, our goal is to make low-noise, phase-sensitive room temperature measurements of the frequency-dependent conductivity of thin films from microwave frequencies into the far-infrared; covering, the frequency range from ionic and dipole relaxation to atomic and electronic processes. To this end, we have developed a high-Q (quality factor) open cavity resonator capable of resolving the complex conductivity of sub-micron films in the range of 100–350?GHz (0.1–0.35 THz, or 0.4–1?meV). In this paper, we use a low-power green laser to excite bound charges in high-resistivity amorphous silicon thin film. Even at room temperature, we can resolve both the dark conductivity and photo-induced changes associated with dielectric relaxation and possibly some small portion of free carriers.

  2. Bendable single crystal silicon thin film transistors formed by printing on plastic substrates

    E-Print Network [OSTI]

    Rogers, John A.

    Bendable single crystal silicon thin film transistors formed by printing on plastic substrates E on plastic substrates using an efficient dry transfer printing technique. In these devices, free standing-Si is then transferred, to a specific location and with a controlled orientation, onto a thin plastic sheet

  3. EVOLUTION AND REGULARITY RESULTS FOR EPITAXIALLY STRAINED THIN FILMS AND MATERIAL VOIDS

    E-Print Network [OSTI]

    Segatti, Antonio

    EVOLUTION AND REGULARITY RESULTS FOR EPITAXIALLY STRAINED THIN FILMS AND MATERIAL VOIDS PAOLO PIOVANO Abstract. We consider free boundary problems that model the evolution of interfaces, and the surface energy, which has a stabilizing effect. First, we introduce the evolution equation with curvature

  4. Growth of macroscopic-area single crystal polyacene thin films on arbitrary substrates

    E-Print Network [OSTI]

    Headrick, Randall L.

    University, Ithaca, New York 14853, USA 3) Cornell High Energy Synchrotron Source, Ithaca New York, 14853 an alternative approach borrowed from recent research on the crystallization of synthetic spheres from Figure 2). The (001) surface has the lowest free energy, and as a result, when a thin film of anthracene

  5. Low cost and high performance light trapping structure for thin-film solar cells

    E-Print Network [OSTI]

    Wang, DongLin; Su, Gang

    2015-01-01

    Nano-scaled dielectric and metallic structures are popular light tapping structures in thin-film solar cells. However, a large parasitic absorption in those structures is unavoidable. Most schemes based on such structures also involve the textured active layers that may bring undesirable degradation of the material quality. Here we propose a novel and cheap light trapping structure based on the prism structured SiO2 for thin-film solar cells, and a flat active layer is introduced purposefully. Such a light trapping structure is imposed by the geometrical shape optimization to gain the best optical benefit. By examining our scheme, it is disclosed that the conversion efficiency of the flat a-Si:H thin-film solar cell can be promoted to exceed the currently certified highest value. As the cost of SiO2-based light trapping structure is much cheaper and easier to fabricate than other materials, this proposal would have essential impact and wide applications in thin-film solar cells.

  6. Photon-Electron Harvesting in Thin-Film Flexible Solar Cells

    E-Print Network [OSTI]

    Wu, Shin-Tson

    ) Dr. Debashis Chanda's Group Cost effective and high efficiency solar cells are important in orderPhoton-Electron Harvesting in Thin-Film Flexible Solar Cells Javaneh Boroumand (12:00 PM ­ 12:30 PM-crystalline silicon (c- Si) remained number one material of choice for harnessing solar energy due to natural

  7. PV prospects: thinPV prospects: thin--film cellsfilm cells Si cell costs

    E-Print Network [OSTI]

    Pulfrey, David L.

    1 PV prospects: thinPV prospects: thin--film cellsfilm cells LECTURE 8 · Si cell costs · optimizing://www.solarbuzz.com/Moduleprices.htm #12;6 Cost of PV modulesCost of PV modules The lowest retail price for a multicrystalline silicon

  8. Analysis of a compressed thin film bonded to a compliant substrate: the energy scaling law

    E-Print Network [OSTI]

    of Mathematical Sciences, New York University, kohn@cims.nyu.edu Department of Mathematics, UniversityAnalysis of a compressed thin film bonded to a compliant substrate: the energy scaling law Robert V energy, i.e. the membrane and bending energy of the film plus the elastic energy of the substrate

  9. Solid state thin film battery having a high temperature lithium alloy anode

    DOE Patents [OSTI]

    Hobson, D.O.

    1998-01-06

    An improved rechargeable thin-film lithium battery involves the provision of a higher melting temperature lithium anode. Lithium is alloyed with a suitable solute element to elevate the melting point of the anode to withstand moderately elevated temperatures. 2 figs.

  10. A study of plasma modification of low k polyimide thin film 

    E-Print Network [OSTI]

    Chung, Taewoo

    2002-01-01

    . The effect of post metal annealing and a SiN[x] barrier layer between metal and polyimide on the properties of the polyimide film was studied. Plasma-modified, low k (dielectric constant), polyimide thin film has been studied for the future interlayer...

  11. Electron cyclotron wave resonance plasma assisted deposition of cubic boron nitride thin films

    E-Print Network [OSTI]

    Zexian, Cao

    Electron cyclotron wave resonance plasma assisted deposition of cubic boron nitride thin films Z. X-pressure plasma source. The electron-cyclotron-wave resonance ECWR plasma served both to sputter the hBN target the high-resolution TEM image and the arc pattern of the 111 reflection from selected-area electron

  12. Thin film growth and characterization of Potassium-Tantalate-Niobate room temperature ferroelectric 

    E-Print Network [OSTI]

    Muntha, Nageswara Rao Venkat

    1995-01-01

    as electro-optical and nonlinear optical coefficients can be observed. Bulk KTN single crystals synthesized from high temperature melts have limited device utility due to the occurence of lamellar growth, twins, etc. For these reasons thin films of KTN find...

  13. Measuring Thickness Changes in Thin Films Due to Chemical Reaction by Monitoring the Surface

    E-Print Network [OSTI]

    Rutenberg, Andrew

    to the study of lithium-ion batteries. Recently metallic alloys M ~M Si, Sn, Al, etc.! have been proposed force microscope, expansion and contraction, Li-ion battery, surface roughness, thin film thickness as possible negative electrode materials for lithium-ion bat- teries ~Yang et al., 1996; Idota et al., 1997

  14. Growth of nano-and microcrystalline silicon thin films at low temperature by pulsed electron deposition

    E-Print Network [OSTI]

    Zexian, Cao

    in a multi-junction design [4]. The solar cells based on nanocrystalline silicon (nc-Si) films have now in electronic and optoelectronic devices, particularly in the fabrication of solar cells. Noticeably, thin-film silicon solar cells take a larger market share than the single- and polycrystalline silicon solar cells

  15. Layer-by-layer assembly of electrically conductive polymer thin films 

    E-Print Network [OSTI]

    Jan, Chien Sy Jason

    2007-09-17

    Layer-by-layer (LbL) assembly was used to produce highly conductive thin films with carbon black (CB) and polyelectrolytes. The effects of sonication and pHadjustment of the deposition mixtures on the conductivity and transparency of deposited films...

  16. Fully Printed, High Performance Carbon Nanotube Thin-Film Transistors on Flexible Substrates

    E-Print Network [OSTI]

    Javey, Ali

    range of large-area electronic applications based on carbon nanotube networks. KEYWORDS: Flexible using SWNT TFTs has been shown.1,5,7,8 In order to enable the use of flexible electronics for largeFully Printed, High Performance Carbon Nanotube Thin-Film Transistors on Flexible Substrates Pak

  17. Thin film electronic devices with conductive and transparent gas and moisture permeation barriers

    DOE Patents [OSTI]

    Simpson, Lin Jay

    2013-12-17

    A thin film stack (100, 200) is provided for use in electronic devices such as photovoltaic devices. The stack (100, 200) may be integrated with a substrate (110) such as a light transmitting/transmissive layer. A electrical conductor layer (120, 220) is formed on a surface of the substrate (110) or device layer such as a transparent conducting (TC) material layer (120,220) with pin holes or defects (224) caused by manufacturing. The stack (100) includes a thin film (130, 230) of metal that acts as a barrier for environmental contaminants (226, 228). The metal thin film (130,230) is deposited on the conductor layer (120, 220) and formed from a self-healing metal such as a metal that forms self-terminating oxides. A permeation plug or block (236) is formed in or adjacent to the thin film (130, 230) of metal at or proximate to the pin holes (224) to block further permeation of contaminants through the pin holes (224).

  18. Activated Charcoal Based Diffusive Gradients in Thin Films for in Situ Monitoring of Bisphenols in Waters

    E-Print Network [OSTI]

    Ma, Lena

    Activated Charcoal Based Diffusive Gradients in Thin Films for in Situ Monitoring of Bisphenols, Gainesville, Florida 32611, United States *S Supporting Information ABSTRACT: Widespread use of bisphenols monitoring of BPs in waters. Endocrine-disrupting chemicals, including bisphenols (BPs), are widely used

  19. Method of forming particulate materials for thin-film solar cells

    DOE Patents [OSTI]

    Eberspacher, Chris; Pauls, Karen Lea

    2004-11-23

    A method for preparing particulate materials useful in fabricating thin-film solar cells is disclosed. Particulate materials is prepared by the method include for example materials comprising copper and indium and/or gallium in the form of single-phase, mixed-metal oxide particulates; multi-phase, mixed-metal particulates comprising a metal oxide; and multinary metal particulates.

  20. In situ Raman spectroscopy of lanthanum-strontium-cobaltite thin films

    E-Print Network [OSTI]

    Breucop, Justin Daniel

    2012-01-01

    Raman spectroscopy is used to probe the structural change of Lanthanum Strontium Cobaltite (La1.xSrxCoO 3 -8) thin films across change in composition (0%-60% strontium) and temperature (30*C-520°C). Raman shift peaks were ...

  1. PREFERENTIAL OXIDATION OF CARBON MONOXIDE IN A THIN-FILM CATALYTIC MICROREACTOR: ADVANTAGES AND LIMITATIONS

    E-Print Network [OSTI]

    Besser, Ronald S.

    PREFERENTIAL OXIDATION OF CARBON MONOXIDE IN A THIN-FILM CATALYTIC MICROREACTOR: ADVANTAGES stream after hydrocarbon fuel reforming and water-gas-shift reactions. This process, referred to as CO intermediate, which enhances the catalytic activity at temperatures below 200°C. With the same catalyst system

  2. Near perfect solar absorption in ultra-thin-film GaAs photonic crystals

    E-Print Network [OSTI]

    John, Sajeev

    Near perfect solar absorption in ultra-thin-film GaAs photonic crystals Sergey Eyderman,*a Alexei voltage of GaAs solar cells. The current world record for high efficiency solar cells is held by thin ultra-thin (GaAs in low-cost solar cells. However, this reduction in the volume

  3. Atomic hydrogen interactions with amorphous carbon thin films Bhavin N. Jariwala,1

    E-Print Network [OSTI]

    Ciobanu, Cristian

    Atomic hydrogen interactions with amorphous carbon thin films Bhavin N. Jariwala,1 Cristian V-scale interactions of H atoms with hydrogenated amorphous carbon a-C:H films were identified using molecular dynamics through a detailed analysis of the MD trajectories. The MD simulations showed that hydrogenation occurs

  4. Identification, Characterization, and Implications of Shadow Degradation in Thin Film Solar Cells

    E-Print Network [OSTI]

    Alam, Muhammad A.

    cells [4]. The problem of shadowing of solar panels has been studied for quite some time; however of a solar cell, showing the dark and light current components. (b) The series connection in a solar panelIdentification, Characterization, and Implications of Shadow Degradation in Thin Film Solar Cells

  5. Photochemical template removal and spatial patterning of zeolite MFI thin films using UV/ozone treatment

    E-Print Network [OSTI]

    Parikh, Atul N.

    Photochemical template removal and spatial patterning of zeolite MFI thin films using UV/ozone (structure code: MFI) following a previously published procedure. The films were illuminated using an ozone. Results presented here indicate that the UV/ozone treatment under nominally room temperature conditions

  6. Analytica Chimica Acta 573574 (2006) 913 Metal oxide thin films as sensing layers for ozone detection

    E-Print Network [OSTI]

    2006-01-01

    Analytica Chimica Acta 573­574 (2006) 9­13 Metal oxide thin films as sensing layers for ozone. Their structural, electrical and ozone sensing properties were analyzed. Structural investigations carried out with ultraviolet light and subsequent oxidation in ozone atmosphere at room temperature. © 2006 Elsevier B.V. All

  7. Reduced Order Based Compensator Control of Thin Film Growth in a CVD Reactor

    E-Print Network [OSTI]

    of the electrical/optical properties and the reliability of wide bandgap semiconductor devices and circuits, material scientists and physicists at North Carolina State University, to integrate new intelligent deposition (CVD) is an important industrial technique used to grow thin films with certain desired properties

  8. Electrical and optical properties of sputtered amorphous vanadium oxide thin films

    SciTech Connect (OSTI)

    Podraza, N. J. [Department of Physics and Astronomy, University of Toledo, Toledo, Ohio 43606 (United States); Gauntt, B. D. [Materials Characterization Department, Sandia National Laboratories, Albuquerque, New Mexico 87185 (United States); Motyka, M. A.; Horn, M. W. [Department of Engineering Science and Mechanics, Pennsylvania State University, University Park, Pennsylvania 16802 (United States); Dickey, E. C. [Department of Materials Science and Engineering, North Carolina State University, Raleigh, North Carolina 27695 (United States)

    2012-04-01

    Amorphous vanadium oxide (VO{sub x}) is a component found in composite nanocrystalline VO{sub x} thin films. These types of composite films are used as thermistors in pulsed biased uncooled infrared imaging devices when containing face centered cubic vanadium monoxide phase crystallites, and substantial fractions of amorphous material in the composite are necessary to optimize device electrical properties. Similarly, optoelectronic devices exploiting the metal-to-semiconductor transition contain the room-temperature monoclinic or high-temperature (>68 deg. C) rutile vanadium dioxide phase. Thin films of VO{sub x} exhibiting the metal-to-semiconductor transition are typically polycrystalline or nanocrystalline, implying that significant amounts of disordered, amorphous material is present at grain boundaries or surrounding the crystallites and can impact the overall optical or electronic properties of the film. The performance of thin film material for either application depends on both the nature of the crystalline and amorphous components, and in this work we seek to isolate and study amorphous VO{sub x}. VO{sub x} thin films were deposited by pulsed dc reactive magnetron sputtering to produce amorphous materials with oxygen contents {>=}2, which were characterized electrically by temperature dependent current-voltage measurements and optically characterized by spectroscopic ellipsometry. Film resistivity, thermal activation energy, and complex dielectric function spectra from 0.75 to 6.0 eV were used to identify the impact of microstructural variations including composition and density.

  9. Enhanced optical absorption in nanopatterned silicon thin films with a nano-cone-hole

    E-Print Network [OSTI]

    Demir, Hilmi Volkan

    .6845, 040.5350. The silicon solar cell is presently dominating the solar cell market, owing to its abundant supply, nearly ideal band gap, and mature fabrication process. Most commer- cial silicon solar cells is consumed, leading to a higher cost for the final product [1]. The thin film silicon solar cell

  10. Scanning Tunneling Microscopy Studies of Metal Clusters Supported on Graphene and Silica Thin Film 

    E-Print Network [OSTI]

    Zhou, Zihao

    2012-10-19

    reveal that the geometric and/or electronic structure of graphene can be adjusted correspondingly. In the study of the silica thin film system, the structure of silica was carefully investigated and our STM images favor for the [SiO4] cluster model...

  11. Epitaxial growth of highly conductive RuO{sub 2} thin films on (100) Si

    SciTech Connect (OSTI)

    Jia, Q.X.; Song, S.G.; Wu, X.D.; Cho, J.H.; Foltyn, S.R.; Findikoglu, A.T.; Smith, J.L.

    1996-02-01

    Conductive RuO{sub 2} thin films have been heteroepitaxially grown by pulsed laser deposition on Si substrates with yttria-stabilized zirconia (YSZ) buffer layers. The RuO{sub 2} thin films deposited under optimized processing conditions are {ital a}-axis oriented normal to the Si substrate surface with a high degree of in-plane alignment with the major axes of the (100) Si substrate. Cross-sectional transmission electron microscopy analysis on the RuO{sub 2}/YSZ/Si multilayer shows an atomically sharp interface between the RuO{sub 2} and the YSZ. Electrical measurements show that the crystalline RuO{sub 2} thin films are metallic over a temperature range from 4.2 to 300 K and are highly conductive with a room-temperature resistivity of 37{plus_minus}2 {mu}{Omega}cm. The residual resistance ratio ({ital R}{sub 300K}/{ital R}{sub 4.2K}) above 5 for our RuO{sub 2} thin films is the highest ever reported for such films on Si substrates. {copyright} {ital 1996 American Institute of Physics.}

  12. Optical properties of Al2O3 thin films grown by atomic layer deposition

    E-Print Network [OSTI]

    Avrutsky, Ivan

    Optical properties of Al2O3 thin films grown by atomic layer deposition Pradeep Kumar,1, * Monika K); published 25 September 2009 We employed the atomic layer deposition technique to grow Al2O3 films fabricated by atomic layer deposition. © 2009 Optical Society of America OCIS codes: 310.6860, 310.2790, 160

  13. Stress effects in sol-gel derived ferroelectric thin films L. Lian and N. R. Sottosa)

    E-Print Network [OSTI]

    Sottos, Nancy R.

    Stress effects in sol-gel derived ferroelectric thin films L. Lian and N. R. Sottosa) Department 26 August 2003; accepted 19 October 2003 Residual stress development during processing of sol investigates the effects of stress on field-induced polarization switching in ferroelectric Pb Zr0.52Ti0.48)O3

  14. Modeling the Early Stages of Thin Film Formation by Energetic Atom Deposition

    E-Print Network [OSTI]

    Ghoniem, Nasr M.

    .M. GHONIEM The early stages of thin film formation are described by a simple hybrid model that couples a set action of a number of unique atomic processes (sputtering, implantation, nucleation, heating system to condense superthermal free particles on a host material. Ion-beam deposition systems deposit

  15. Improvements in Processing and Stretchability of Super Gas Barrier Multilayer Thin Films 

    E-Print Network [OSTI]

    Xiang, Fangming

    2015-03-31

    parameter. A 7-bilayer PEI/PAA thin film assembled using optimized spraying parameters exhibited better gas barrier than a dip-coated multilayer prepared using the same deposition time for each layer. These findings pave the way for using the LbL technique...

  16. Metal Oxide Thin Films Deposited from Metal Organic Precursors in Supercritical CO2 Solutions

    E-Print Network [OSTI]

    Gougousi, Theodosia

    Metal Oxide Thin Films Deposited from Metal Organic Precursors in Supercritical CO2 Solutions and oxidizing agents are delivered in liquid and supercritical CO2. A cyclic deposition process is presented properties of supercritical CO2 can aid in the delivery of precursors and in the removal of byproducts

  17. ORAL REFERENCE: ICF100572OR FIDUCIAL MARKS AS MEASURES OF THIN FILM

    E-Print Network [OSTI]

    Volinsky, Alex A.

    ORAL REFERENCE: ICF100572OR FIDUCIAL MARKS AS MEASURES OF THIN FILM CRACK ARREST TOUGHNESS Alex A presented in the paper. KEYWORDS Fiducial marks, adhesion, fracture, delamination, crack arrest, crack tip). This technique was shown to work with ductile metallic films (Al, Cu, Au, Cr) [2, 4-9, 15], ceramic (Ta2N) [10

  18. Technical Note Fiducial marks as measures of thin film crack arrest toughness

    E-Print Network [OSTI]

    Volinsky, Alex A.

    Technical Note Fiducial marks as measures of thin film crack arrest toughness Alex A. Volinsky a Published by Elsevier Science Ltd. Keywords: Fiducial marks; Adhesion; Fracture; Delamination; Crack arrest). This technique was shown to work with ductile metallic films (Al, Cu, Au, Cr) [2,4­9,15], ceramic (Ta2N) [10

  19. Investigation of the formation of nanostructures on silicon thin films by excimer laser irradiation

    E-Print Network [OSTI]

    Chaudhary, Vipin

    Investigation of the formation of nanostructures on silicon thin films by excimer laser irradiation-pulse excimer laser irradiation. The fabricated structures have heights of about 1 m and apical radii on an insulator substrate is irradiated in air environment with a single 25ns pulse from a KrF excimer laser

  20. Grain growth in ZrFe thin films during in situ ion irradiation in a TEM

    E-Print Network [OSTI]

    Motta, Arthur T.

    Grain growth in Zr­Fe thin films during in situ ion irradiation in a TEM D. Kaoumi a,*, A.T. Motta Laboratory, Argonne, IL 060493, USA Available online 2 November 2005 Abstract In situ ion-beam irradiation was used to study irradiation induced grain growth in co-sputter-deposited Zr/xFe (0% 6 x 6 4