National Library of Energy BETA

Sample records for tires iii super

  1. Burning tires for fuel and tire pyrolysis: air implications

    SciTech Connect (OSTI)

    Clark, C.; Meardon, K.; Russell, D.

    1991-12-01

    The document was developed in response to increasing inquiries into the environmental impacts of burning waste tires in process equipment. The document provides information on the use of whole, scrap tires and tire-derived-fuel (TDF) as combustion fuel and on the pyrolysis of scrap tires. The use of whole tires and TDF as a primary fuel is discussed for dedicated tire-to-energy facilities. The use of whole tires and TDF as a supplemental fuel is discussed for cement manufacturing plants, electric utilities, pulp and paper mills, and other industrial processes. The focus of the document is on the impact of burning whole tires and TDF on air emissions. Test data are presented and, in most instances, compared with emissions under baseline conditions (no tires or TDF in the fuel). The control devices used in these industries are discussed and, where possible, their effectiveness in controlling emissions from the burning of whole tires or TDF is described. In addition, the report provides information on the processes themselves that use whole tires or TDF, the modifications to the processes that allowed the use of whole tires or TDF, and the operational experiences of several facilities using whole tires or TDF. The economic feasibility of using whole tires and TDF for the surveyed industries is discussed. Finally, contacts for State waste tire programs are presented.

  2. Waste tire recycling by pyrolysis

    SciTech Connect (OSTI)

    Not Available

    1992-10-01

    This project examines the City of New Orleans' waste tire problem. Louisiana State law, as of January 1, 1991, prohibits the knowing disposal of whole waste tires in landfills. Presently, the numerous waste tire stockpiles in New Orleans range in size from tens to hundreds of tires. New Orleans' waste tire problem will continue to increase until legal disposal facilities are made accessible and a waste tire tracking and regulatory system with enforcement provisions is in place. Tires purchased outside of the city of New Orleans may be discarded within the city's limits; therefore, as a practical matter this study analyzes the impact stemming from the entire New Orleans metropolitan area. Pyrolysis mass recovery (PMR), a tire reclamation process which produces gas, oil, carbon black and steel, is the primary focus of this report. The technical, legal and environmental aspects of various alternative technologies are examined. The feasibility of locating a hypothetical PMR operation within the city of New Orleans is analyzed based on the current economic, regulatory, and environmental climate in Louisiana. A thorough analysis of active, abandoned, and proposed Pyrolysis operations (both national and international) was conducted as part of this project. Siting a PMR plant in New Orleans at the present time is technically feasible and could solve the city's waste tire problem. Pending state legislation could improve the city's ability to guarantee a long term supply of waste tires to any large scale tire reclamation or recycling operation, but the local market for PMR end products is undefined.

  3. Tire deflation device

    DOE Patents [OSTI]

    Barker, Stacey G. (Idaho Falls, ID) [Idaho Falls, ID

    2010-01-05

    A tire deflation device includes (1) a component having a plurality of bores, (2) a plurality of spikes removably insertable into the plurality of bores and (3) a keeper within each among the plurality of bores, the keeper being configured to contact a sidewall surface of a spike among the plurality of spikes and to exert force upon the sidewall surface. In an embodiment, the tire deflation device includes (a) a component including a bore in a material, the bore including a receiving region, a sidewall surface and a base surface, (b) a channel extending from the sidewall surface into the material, (c) a keeper having a first section housed within the channel and a second section which extends past the sidewall surface into the receiving region, and (d) a spike removably insertable into the bore.

  4. Photochemistry in terrestrial exoplanet atmospheres. III. Photochemistry and thermochemistry in thick atmospheres on super Earths and mini Neptunes

    SciTech Connect (OSTI)

    Hu, Renyu; Seager, Sara

    2014-03-20

    Some super Earths and mini Neptunes will likely have thick atmospheres that are not H{sub 2}-dominated. We have developed a photochemistry-thermochemistry kinetic-transport model for exploring the compositions of thick atmospheres on super Earths and mini Neptunes, applicable for both H{sub 2}-dominated atmospheres and non-H{sub 2}-dominated atmospheres. Using this model to study thick atmospheres for wide ranges of temperatures and elemental abundances, we classify them into hydrogen-rich atmospheres, water-rich atmospheres, oxygen-rich atmospheres, and hydrocarbon-rich atmospheres. We find that carbon has to be in the form of CO{sub 2} rather than CH{sub 4} or CO in a H{sub 2}-depleted water-dominated thick atmosphere and that the preferred loss of light elements from an oxygen-poor carbon-rich atmosphere leads to the formation of unsaturated hydrocarbons (C{sub 2}H{sub 2} and C{sub 2}H{sub 4}). We apply our self-consistent atmosphere models to compute spectra and diagnostic features for known transiting low-mass exoplanets GJ 1214 b, HD 97658 b, and 55 Cnc e. For GJ 1214 b, we find that (1) C{sub 2}H{sub 2} features at 1.0 and 1.5 ?m in transmission and C{sub 2}H{sub 2} and C{sub 2}H{sub 4} features at 9-14 ?m in thermal emission are diagnostic for hydrocarbon-rich atmospheres; (2) a detection of water-vapor features and a confirmation of the nonexistence of methane features would provide sufficient evidence for a water-dominated atmosphere. In general, our simulations show that chemical stability has to be taken into account when interpreting the spectrum of a super Earth/mini Neptune. Water-dominated atmospheres only exist for carbon to oxygen ratios much lower than the solar ratio, suggesting that this kind of atmospheres could be rare.

  5. Waste tire recycling by pyrolysis

    SciTech Connect (OSTI)

    Not Available

    1992-10-01

    This project examines the City of New Orleans` waste tire problem. Louisiana State law, as of January 1, 1991, prohibits the knowing disposal of whole waste tires in landfills. Presently, the numerous waste tire stockpiles in New Orleans range in size from tens to hundreds of tires. New Orleans` waste tire problem will continue to increase until legal disposal facilities are made accessible and a waste tire tracking and regulatory system with enforcement provisions is in place. Tires purchased outside of the city of New Orleans may be discarded within the city`s limits; therefore, as a practical matter this study analyzes the impact stemming from the entire New Orleans metropolitan area. Pyrolysis mass recovery (PMR), a tire reclamation process which produces gas, oil, carbon black and steel, is the primary focus of this report. The technical, legal and environmental aspects of various alternative technologies are examined. The feasibility of locating a hypothetical PMR operation within the city of New Orleans is analyzed based on the current economic, regulatory, and environmental climate in Louisiana. A thorough analysis of active, abandoned, and proposed Pyrolysis operations (both national and international) was conducted as part of this project. Siting a PMR plant in New Orleans at the present time is technically feasible and could solve the city`s waste tire problem. Pending state legislation could improve the city`s ability to guarantee a long term supply of waste tires to any large scale tire reclamation or recycling operation, but the local market for PMR end products is undefined.

  6. III

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    III .. III A HIGH RESOLUTION STUDY OF ISOBARIC ANAL.OGUE STATES IN 41K AND 23 Na by George A lbert Keyworth II Department of Physics Duke University A dissertation submitted in partial fulfillment of the requirements for the degree of Doctor of Philosophy in the Department of Physics in the Graduate School of Arts and Sciences of Duke University 1968 I I I I I I I I I I I I I I I I I I I A HIGH RESOLUTION STUDY OF ISOBARIC ANALOGUE STATES IN 41 K - AND 23 Na ,. by George Albert Keyworth II

  7. Scrap tires: a resource and technology evaluation of tire pyrolysis and other selected alternate technologies

    SciTech Connect (OSTI)

    Dodds, J.; Domenico, W.F.; Evans, D.R.; Fish, L.W.; Lassahn, P.L.; Toth, W.J.

    1983-11-01

    The results of a technical and economic evaluation of scrap tire pyrolysis are presented and some other alternative uses for scrap tires are discussed. A scrap tire, by definition in this report, is one for which there is no economic end use. Information is presented on the scrap tire resource, pyrolysis processes, pyrolysis products (char, oil, and gas), markets for these products, and the economics of tire pyrolysis. A discussion is presented on alternative ideas for using scrap tires as an energy resource.

  8. New Tire Technologies Can Improve Fuel Efficiency by More Than...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    by More Than 5% New Tire Technologies Can Improve Fuel Efficiency by More Than 5% Cooper Tire recently developed concept tires that can improve fuel efficiency by 5.5%,...

  9. Alternative Fuels Data Center: Low Rolling Resistance Tires

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    Low Rolling Resistance Tires to someone by E-mail Share Alternative Fuels Data Center: Low Rolling Resistance Tires on Facebook Tweet about Alternative Fuels Data Center: Low Rolling Resistance Tires on Twitter Bookmark Alternative Fuels Data Center: Low Rolling Resistance Tires on Google Bookmark Alternative Fuels Data Center: Low Rolling Resistance Tires on Delicious Rank Alternative Fuels Data Center: Low Rolling Resistance Tires on Digg Find More places to share Alternative Fuels Data

  10. Tire with outer groove containing bonded tube

    DOE Patents [OSTI]

    Welter, Carolin Anna; Chandra, Dinesh; Benedict, Robert Leon

    2016-02-16

    The invention relates generally to a pneumatic rubber tire which contains an outer, annular, circular groove which contains a flexible tube bonded to the walls of the groove.

  11. Vacuum pyrolysis of used tires

    SciTech Connect (OSTI)

    Roy, C.; Darmstadt, H.; Benallal, B.; Chaala, A.; Schwerdtfeger, A.E.

    1995-11-01

    The vacuum pyrolysis of used tires enables the recovery of useful products, such as pyrolytic oil and pyrolytic carbon black (CB{sub P}). The light part of the pyrolytic oil contains dl-limonene which has a high price on the market. The naphtha fraction can be used as a high octane number component for gasoline. The middle distillate demonstrated mechanical and lubricating properties similar to those of the commercial aromatic oil Dutrex R 729. The heavy oil was tested as a feedstock for the production of needle coke. It was found that the surface morphology of CB{sub P} produced by vacuum pyrolysis resembles that of commercial carbon black. The CB{sub P} contains a higher concentration of inorganic compounds (especially ZnO and S) than commercial carbon black. The pyrolysis process feasibility looks promising. One old tire can generate upon vacuum pyrolysis, incomes of at least $2.25 US with a potential of up to $4.83 US/tire upon further product improvement. The process has been licensed to McDermott Marketing Servicing Inc. (Houston) for its exploitation in the US.

  12. Scrap tire utilization via surface modification

    SciTech Connect (OSTI)

    Bauman, B.D. )

    1990-01-01

    Air Products and Chemicals, Inc. is developing a novel approach to reusing scrap tire rubber, which will be described in this presentation. In addition to consuming scrap tires, this technology represents a new approach to material engineering. Furthermore, this method of rubber recycle is most efficient in terms of energy recovery. 4 figs.

  13. Scrap tire management in the mid south region

    SciTech Connect (OSTI)

    Blumenthal, M.

    1996-08-01

    The Scrap Tire Management Council (STMC) is a North American tire manufacturer-sponsored advocacy organization, created to identify and promote environmentally and economically sound markets for scrap tires. This presentation gives a national overview of the scrap tire situation, and focuses on the Tennessee and Mid-south region. National generation rates and markets for scrap tires are discussed, and markets for scrap tires are described. The major markets identified are fuel, rubber products, and civil engineering applications. Three technologies that may have an impact on scrap tire recycling are discussed: pyrolysis, gasification, and devulcanization.

  14. Scrap tire pyrolysis: Experiment and modelling

    SciTech Connect (OSTI)

    Napoli, A.; Soudais, Y.; Lecomte, D.; Castillo, S.

    1997-12-01

    Pyrolysis of waste, usually organic solids like tires, plastics or composite materials, is an alternative thermal waste treatment technology. Three main physical and chemical mechanisms - i.e.: chemical kinetics, internal heat transfer and external heat transfer - have to be considered when modelling the degradation of solid waste particles. Because of the lack of physical properties for wastes most of the models described in the literature use basic data obtained on the pyrolysis of coal, wood and biomass. In this work, the authors report basic information on the thermal degradation of tire samples at small scale: Thermogravimetric analyser (TGA) and differential scanning calorimeter (DSC), as well as direct and indirect measurements of thermal and physical properties (thermal conductivity of the tire and of the char, porosity, density, specific heat). Pyrolysis experiments on tire samples are performed in an imaging furnace. The experimental results are compared to theoretical values deduced from models that take into account physical property measurements.

  15. THE PHOTOECCENTRIC EFFECT AND PROTO-HOT JUPITERS. III. A PAUCITY OF PROTO-HOT JUPITERS ON SUPER-ECCENTRIC ORBITS

    SciTech Connect (OSTI)

    Dawson, Rebekah I.; Murray-Clay, Ruth A.; Johnson, John Asher

    2015-01-10

    Gas giant planets orbiting within 0.1 AU of their host stars are unlikely to have formed in situ and are evidence for planetary migration. It is debated whether the typical hot Jupiter smoothly migrated inward from its formation location through the proto-planetary disk, or was perturbed by another body onto a highly eccentric orbit, which tidal dissipation subsequently shrank and circularized during close stellar passages. Socrates and collaborators predicted that the latter model should produce a population of super-eccentric proto-hot Jupiters readily observable by Kepler. We find a paucity of such planets in the Kepler sample, which is inconsistent with the theoretical prediction with 96.9% confidence. Observational effects are unlikely to explain this discrepancy. We find that the fraction of hot Jupiters with an orbital period P > 3days produced by the star-planet Kozai mechanism does not exceed (at two-sigma) 44%. Our results may indicate that disk migration is the dominant channel for producing hot Jupiters with P > 3days. Alternatively, the typical hot Jupiter may have been perturbed to a high eccentricity by interactions with a planetary rather than stellar companion, and began tidal circularization much interior to 1 AU after multiple scatterings. A final alternative is that early in the tidal circularization process at high eccentricities tidal circularization occurs much more rapidly than later in the process at low eccentricities, although this is contrary to current tidal theories.

  16. Improving Vehicle Fuel Efficiency Through Tire Design, Materials...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    To develop a new class of tires in the replacement market that improves fuel efficiency by a minimum of 3% and reduces overall tire weight by 20%. This presentation does...

  17. Tire gassification and combustion system

    SciTech Connect (OSTI)

    Nance, D.; Towne, G.A.

    1992-04-07

    This patent describes a system for disposing of a material such as vehicle tires and similar substantially organic matter and generating useful heat therefrom. It comprises gasification means for holding an amount of the material to be disposed while the material is allowed to partially combust and for containing combustible gas produced thereby, the gasification means comprising a substantially air tight gasification chamber having at least one access way for inserting the material therein; inlet means for receiving a controlled amount of oxygen containing gas into the gasification means, the inlet means comprising a tuyere disposed in the air tight gasification chamber and a blower connected to the tuyere; removal means for removing the combustible gas from the gasification means, the removal means comprising a gas outlet located above the tuyere in the gasification chamber such that substantially amounts of the combustible gases produced by the partially combusted material exits through the gas outlet; primary combustion means for receiving and mixing the combustible gas removed from the gasification means with an oxygen containing gas and burning the combustible gas; and means for directing the combustion products to a heat utilizing device.

  18. Materials Approach to Fuel Efficient Tires

    SciTech Connect (OSTI)

    Votruba-Drzal, Peter; Kornish, Brian

    2015-06-30

    The objective of this project was to design, develop, and demonstrate fuel efficient and safety regulation compliant tire filler and barrier coating technologies that will improve overall fuel efficiency by at least 2%. The program developed and validated two complementary approaches to improving fuel efficiency through tire improvements. The first technology was a modified silica-based product that is 15% lower in cost and/or enables a 10% improvement in tread wear while maintaining the already demonstrated minimum of 2% improvement in average fuel efficiency. The second technology was a barrier coating with reduced oxygen transmission rate compared to the state-of-the-art halobutyl rubber inner liners that will provide extended placarded tire pressure retention at significantly reduced material usage. A lower-permeance, thinner inner liner coating which retains tire pressure was expected to deliver the additional 2% reduction in fleet fuel consumption. From the 2006 Transportation Research Board Report1, a 10 percent reduction in rolling resistance can reduce consumer fuel expenditures by 1 to 2 percent for typical vehicles. This savings is equivalent to 6 to 12 gallons per year. A 1 psi drop in inflation pressure increases the tire's rolling resistance by about 1.4 percent.

  19. Tire Development for Effective Transportation and Utilization of Used Tires, CRADA 01-N044, Final Report

    SciTech Connect (OSTI)

    Susan M. Maley

    2004-03-31

    Scrap tires represent a significant disposal and recycling challenge for the United States. Over 280 million tires are generated on an annual basis, and several states have large stockpiles or abandoned tire piles that are slated for remediation. While most states have programs to address the accumulation and generation of scrap tires, most of these states struggle with creating and sustaining recycling or beneficial end use markets. One of the major issues with market development has been the costs associated with transporting and processing the tires into material for recycling or disposal. According to a report by the Rubber Manufactures Association tire-derived fuel (TDF) represents the largest market for scrap tires, and approximately 115 million tires were consumed in 2001 as TDF (U.S. Scrap Tire Markets, 2001, December 2002, www.rma.org/scraptires). This market is supported primarily by cement kilns, followed by various industries including companies that operate utility and industrial boilers. However the use of TDF has not increased and the amount of TDF used by boiler operators has declined. The work completed through this cooperative research and development agreement (CRADA) has shown the potential of a mobile tire shredding unit to economically produce TDF and to provide an alterative low cost fuel to suitable coal-fired power systems. This novel system addresses the economic barriers by processing the tires at the retailer, thereby eliminating the costs associated with hauling whole tires. The equipment incorporated into the design allow for small 1-inch chunks of TDF to be produced in a timely fashion. The TDF can then be co-fired with coal in suitable combustion systems, such as a fluidized bed. Proper use of TDF has been shown to boost efficiency and reduce emissions from power generation systems, which is beneficial to coal utilization in existing power plants. Since the original scope of work outlined in the CRADA could not be completed because

  20. Passive tire pressure sensor and method

    DOE Patents [OSTI]

    Pfeifer, Kent Bryant; Williams, Robert Leslie; Waldschmidt, Robert Lee; Morgan, Catherine Hook

    2006-08-29

    A surface acoustic wave device includes a micro-machined pressure transducer for monitoring tire pressure. The device is configured having a micro-machined cavity that is sealed with a flexible conductive membrane. When an external tire pressure equivalent to the cavity pressure is detected, the membrane makes contact with ridges on the backside of the surface acoustic wave device. The ridges are electrically connected to conductive fingers of the device. When the detected pressure is correct, selected fingers on the device will be grounded producing patterned acoustic reflections to an impulse RF signal. When the external tire pressure is less than the cavity reference pressure, a reduced reflected signal to the receiver results. The sensor may further be constructed so as to identify itself by a unique reflected identification pulse series.

  1. Passive tire pressure sensor and method

    DOE Patents [OSTI]

    Pfeifer, Kent Bryant; Williams, Robert Leslie; Waldschmidt, Robert Lee; Morgan, Catherine Hook

    2007-09-04

    A surface acoustic wave device includes a micro-machined pressure transducer for monitoring tire pressure. The device is configured having a micro-machined cavity that is sealed with a flexible conductive membrane. When an external tire pressure equivalent to the cavity pressure is detected, the membrane makes contact with ridges on the backside of the surface acoustic wave device. The ridges are electrically connected to conductive fingers of the device. When the detected pressure is correct, selected fingers on the device will be grounded producing patterned acoustic reflections to an impulse RF signal. When the external tire pressure is less than the cavity reference pressure, a reduced reflected signal to the receiver results. The sensor may further be constructed so as to identify itself by a unique reflected identification pulse series.

  2. Improving Vehicle Fuel Efficiency Through Tire Design, Materials...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    3 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review ... More Documents & Publications Improving Vehicle Fuel Efficiency Through Tire Design, ...

  3. Improving Vehicle Fuel Efficiency Through Tire Design, Materials...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    2 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review ... More Documents & Publications Improving Vehicle Fuel Efficiency Through Tire Design, ...

  4. Goodyear Tire Plant Gains Traction on Energy Savings After Completing...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Goodyear operates more than 60 facilities in 26 countries, including the Union City, Tennessee, plant pictured above. Goodyear Tire Plant Gains Traction on Energy Savings After ...

  5. Passive tire pressure sensor and method (Patent) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Title: Passive tire pressure sensor and method A surface acoustic wave device includes a micro-machined pressure transducer for monitoring tire pressure. The device is configured ...

  6. Super Boiler Update

    SciTech Connect (OSTI)

    2007-10-01

    This presentation from the 2007 American Boiler Manufacturers Association Manufacturers Conference provides an update of the First Generation Super Boiler.

  7. An unresolved riddle: Tire chips, two roadbeds, and spontaneous reactions

    SciTech Connect (OSTI)

    Nightingale, D.E.B.; Green, W.P.

    1997-12-31

    Experience with road fills in Washington State constructed with thick layers of tire chips spontaneously burning has led to a decrease in tire chip use nationally. The field measurements and samples taken indicate that a pyrolitic reaction occurred at two roadfill sites in Washington State based on a comparison to know pyrolytic reactions in controlled settings. Pyrolysis in roadbeds containing tire chips is a new phenomena previously only found in open piles of processed tire chips. Because water and nutrients were introduced, iron oxidation, microbial digestion, and chemical oxidation are possible factors contributing to the pyrolytic reactions at the two Washington State sites. A new heat ignition theory from Japanese experiments suggests a theoretical answer to practical design depth limits in roadbeds and tire chip piles may be climate (air temperature) and depth dependent.

  8. Reprocessing of used tires into activated carbon and other products

    SciTech Connect (OSTI)

    Teng, H.; Serio, M.A.; Wojtowicz, M.A.; Bassilakis, R.; Solomon, P.R.

    1995-09-01

    Landfilling used tires which are generated each year in the US is increasingly becoming an unacceptable solution. A better approach, from an environmental and economic standpoint, is to thermally reprocess the tires into valuable products such as activated carbon, other solid carbon forms (carbon black, graphite, and carbon fibers), and liquid fuels. In this study, high surface area activated carbons (> 800 m{sup 2}/g solid product) were produced in relatively high yields by pyrolysis of tires at up to 900 C, followed by activation in CO{sub 2} at the same temperature. The surface areas of these materials are comparable with those of commercial activated carbons. The efficiency of the activation process (gain in specific surface area/loss in mass) was greatest (up to 138 m{sup 2}/g original tire) when large pieces of tire material were used ({approximately} 170 mg). Oxygen pretreatment of tires was found to enhance both the yield and the surface area of the carbon product. High-pressure treatment of tires at low temperatures (< 400 C) is an alternative approach if the recovery of carbon black or fuel oils is the primary objective.

  9. Fluidized-bed combustion of scrap tires: Technical note

    SciTech Connect (OSTI)

    Shang, J.Y.; Mei, J.S.; Notestein, J.E.

    1981-10-01

    An introduction to fluidized-bed combustion (FBC) is presented in Section 2.0. Based on this discussion of its technical development, FBC is then presented as a means of scrap tire disposal. In Section 3.0, scrap tire disposal is reviewed in the categories of (1) physical applications, (2) chemical applications, (3) pyrolysis, and (4) incineration for thermal energy recovery. Scrap tire disposal is reviewed on the basis of (1) environmental acceptability, (2) conservation of resources, (3) impact on existing industries, (4) operational feasibility, and (5) special features. The focus of this report is the fluidized-bed incineration of scrap tires for thermal energy recovery. The factors that affect scrap tire combustion are discussed in Section 4.0. These factors are (1) agitation, (2) temperature, (3) excess air, (4) residence time, (5) feed uniformity, (6) solid waste handling, and (7) pollutants emission control. In reviewing these incineration processes, (1) fuel flexibility, (2) environmental acceptability, (3) combustion efficiency, and (4) operational reliability are discussed. The results from a tire incineration experiment conducted at the Morgantown Energy Technology Center are presented in Section 5.0, and a conceptual fluidized-bed combustor is discussed in Section 6.0. Future considerations in the FBC of scrap tires are discussed in Section 7.0. 8 refs., 6 figs., 6 tabs.

  10. Goodyear Tire Plant Gains Traction on Energy Savings After Completing...

    Broader source: Energy.gov (indexed) [DOE]

    describes how the Goodyear Tire Plant saved approximately 93,000 MMBtu and 875,000 annually after increasing steam system energy efficiency in their Union City, Tennessee, plant. ...

  11. Super-Heavy Element Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Targets for Super-Heavy Element Research Presented at International Workshop on Super-Heavy Element Research SHE-15 J. B. Roberto Oak Ridge National Laboratory Oak Ridge,...

  12. Super recycled water: quenching computers

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Super recycled water: quenching computers Super recycled water: quenching computers New facility and methods support conserving water and creating recycled products. Using reverse ...

  13. Firm eyes savings from tires-to-fuel system

    SciTech Connect (OSTI)

    Barber, J.

    1983-01-31

    A $600,000 pyrolysis system to convert tire scraps into methane will eliminate a tire retreading company's landfill and boiler fuel costs and achieve a five-year payback. The process also yields steel belts, fibers, and carbon black byproducts that can be sold for additional revenue. Heat from the hot exhaust gases will be recycled to the combustion chamber. A 10% federal energy tax credit and a 10% investment tax credit lowered the capital costs for $480,000. (DCK)

  14. Recovery of commercially valuable products from scrap tires

    SciTech Connect (OSTI)

    Roy, C.

    1993-07-20

    A process is described for producing carbon black by vacuum pyrolysis of used rubber tires, which comprises pyrolysing used rubber tire material at a temperature in the range of about 490 C to about 510 C under an absolute pressure of less than about 5 kPa, and recovering a solid carbonaceous material containing carbon black having an iodine adsorption number of about 130 to about 150 mg/g.

  15. Waste tires as auxiliary fuel for cement kilns

    SciTech Connect (OSTI)

    Dodds, J.

    1987-01-01

    The subject I have been asked to speak about is the utilization of scrap tires as an auxiliary fuel for cement kilns. My experience with scrap tires began five years ago when we performed a technical and economic evaluation for tire pyrolysis. I work for the Idaho National Engineering Laboratory which is supported by the Department of Energy. My interest in scrap tires continued; in 1984 the Department of Energy and the Portland Cement Association jointly sponsored a conference on the utilization of scrap tires in cement kilns. Most of my remarks today are based upon that conference along with some current information in the US. Mr. Sladek requested that I speak on the combustion process, the progress to date, and the factors that impede or encourage implementation of using scrap tires in cement kilns. For discussion purposes it would help if we had a common understanding of the cement manufacturing process. Cement is made by heating a mixture of finely ground limestone and silica from clay or sand to about 1450/degree/C in a large rotating kiln. The heat causes the limestone to decarbonate and subsequently react with the silica to form calcium silicates. 5 figs.

  16. SuperNEMO status

    SciTech Connect (OSTI)

    Chapon, A. [Universite de Caen Basse-Normandie, ENSICAEN, LPC Caen, UMR 6534, 6 boulevard du Marechal Juin, 14050 CAEN Cedex (France); Collaboration: SUPERNEMO Collaboration

    2011-12-16

    The SuperNEMO experiment aims to reach a sensitivity up to 10{sup 26} years on the half-life of neutrinoless double beta decay. The SuperNEMO project strongly inherits from the previous Nemo3 experiment. It will consist of a ''tracko-calo'' modular detector with at least 100 kg of betabeta isotope. The current status of the main R and D tasks will be presented: enrichment and production of source foils, radiopurity control, tracker and calorimeter.

  17. Goodyear Testing Self-Inflating Tire Systems in U.S. Trucking Fleets

    Broader source: Energy.gov [DOE]

    The Goodyear Tire & Rubber Company is demonstrating its award-winning self-inflating tires by testing the Air Maintenance Technology (AMT) on U.S. trucking fleets. Goodyear has received...

  18. Fact #763: January 21, 2013 Eighty-four Percent of Scrapped Tires...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Ground rubber, which is used for sports surfacing, asphalt, playgrounds, and other molded ... U.S. Scrap Tire Uses, 2009 Market Tons (Thousands) Tire-derived Fuel 2,084.8 Ground Rubber ...

  19. EERE Success Story-Goodyear Testing Self-Inflating Tire Systems in U.S.

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Trucking Fleets | Department of Energy Goodyear Testing Self-Inflating Tire Systems in U.S. Trucking Fleets EERE Success Story-Goodyear Testing Self-Inflating Tire Systems in U.S. Trucking Fleets April 7, 2015 - 4:52pm Addthis This graphic shows how Goodyear's new Air Maintenance Technology -- also called the self-regulating tire -- works. | Graphic courtesy of Goodyear. This graphic shows how Goodyear's new Air Maintenance Technology -- also called the self-regulating tire -- works. |

  20. 54.5 MPG and Beyond: New Tire Technology Pumps Up Fuel Savings | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy New Tire Technology Pumps Up Fuel Savings 54.5 MPG and Beyond: New Tire Technology Pumps Up Fuel Savings December 12, 2012 - 10:30am Addthis This graphic shows how Goodyear's new Air Maintenance Technology -- also called the self-regulating tire -- works. | Graphic courtesy of Goodyear. This graphic shows how Goodyear's new Air Maintenance Technology -- also called the self-regulating tire -- works. | Graphic courtesy of Goodyear. Rebecca Matulka Rebecca Matulka Former Digital

  1. EERE Energy Impacts: Self-Inflating Tires Could Save You Money on Gas, Improve Driving Safety

    Broader source: Energy.gov [DOE]

    The self-regulating tire system that the Goodyear Tire & Rubber Company has developed with funding from the Office of Energy Efficiency and Renewable Energy (EERE) uses a new technology called Air Maintenance Technology (AMT) that automatically manages air pressure in tires, so you don't have to.

  2. Disposal techniques with energy recovery for scrapped vehicle tires

    SciTech Connect (OSTI)

    Sladek, T.A.; Demos, E.K.

    1987-06-01

    The scrap tire disposal problem is serious and widespread. However there are a number of promising management options, especially using the rubber as a supplemental fuel for existing combustors. The most cost-effective approach to dealing with Denver's tire stockpile appears to be shredding to a coarse size range, storing the shreds in a secure area, and marketing the rubber to nearby cement kilns, lime kilns, and boilers. This interim step would greatly reduce the volume of the pile, facilitate the Superfund evaluation, reduce fire and disease hazards, and simplify subsequent materials handling. Further processing to obtain rubber chips or crumbs may also be practical. However the industry and the markets would have to emerge over time. New power plants or pyrolysis facilities would be impeded by the low energy prices in Denver and the need for elaborate pollution controls. Landfilling could be considered as a last resort. Landfilling costs would be minimized if the tires are shredded. Chapter 2 discusses the tire disposal problem and the general options for tire management. Chapter 3 describes the methodology used to analyze Denver's situation and presents the results and conclusions obtained. This includes evaluation of strategies to implement the more promising resource recovery options in the Denver area. Chapter 4 summarizes the lessons learned and identifies impediments and uncertainties that need to be addressed in any future studies. The Appendix contains additional acknowledgments, a list of references, definitions for the acronyms and units used in the text, the agenda for the tire workshop, and a brief description of a stockpile fire near Denver in June 1987. 111 refs., 6 tabs.

  3. Vacuum pyrolyzed tire oil as a coal solvent

    SciTech Connect (OSTI)

    Orr, E.C.; Shi, Y.; Ji, Q.

    1995-12-31

    Coal liquefaction is highly dependent upon the type of coal liquefaction solvent used. The solvent must readily solubilize the coal and must act as an effective hydrogen donor or shuttler. Oil derived from the vacuum pyrolysis of used rubber tires has recently been used as a coal solvent with good conversion of coal to liquids in a hydrogen atmosphere. All experiments were completed in shaken tubing reactors at 450{degrees}C utilizing a bituminous coal. Results show the effectiveness of the pyrolyzed tire oil as a coal liquefaction solvent depends upon hydrogen pressure. Electron probe microanalysis data reveal good dispersion of the molybdenum catalyst in coal particles taken from liquefaction experiments.

  4. Combustion and inorganic emissions of ground waste tires

    SciTech Connect (OSTI)

    Levendis, Y.A.; Atal, A.; Steciak, J.

    1995-12-31

    An experimental study was undertaken to assess the combustion characteristics and emissions of SO{sub 2}, NO{sub x} and CO{sub 2} gases from ground waste tires. Results were contrasted with those obtained from burning pulverized coal. Laboratory bench-scale experiments were conducted in a drop-tube, laminar-flow furnace, in air at fuel-lean conditions, at gas temperatures ranging from 1300 K to 1600 K. Two particle size cuts were burned from both materials, 75-90 {mu}m and 180-212 {mu}m. Blends of coal and tire particles, at equal weight ratios, were also burned. Pyrometric and cinematographic observations revealed that the coal particles exhibited distinct volatile and char combustion phases, while tire particles exhibited a distinct primary volatile phase followed by a char combustion phase, which was accompanied by burning of secondary pyrolysis products. SO{sub 2} emissions of burning ground tires increased from 160 to 500 ppm as the temperature increased from 1300 K to 1600 K. Combustion of coal produced SO{sub 2} emissions in the neighborhood of 200-300 ppm (corresponding to 40 to 60 wt% of its sulfur content) independent of the gas temperature. The blend of coal and tire particles (equal mass ratios) exhibited SO{sub 2} values which fell in between the above. NO{sub x} emissions were constant at approximately 175 ppm for tire crumb (corresponding to approximately 45 wt% of its fuel nitrogen content) and 625 ppm for coal (corresponding to 55 wt% of its fuel nitrogen content) in the temperature range studied. CO{sub 2} emissions from tire were 8-9 molar %, while for coal particles they were 5-7 molar %; the upper limits corresponded to approximately 100% combustion efficiency. As a means to reduce the SO{sub 2} emissions, pulverized coal and tire crumb were fluidized together with particles of a calcium bearing sorbent - calcium magnesium acetate (CMA). CMA has been identified as an effective SO{sub 2} scrubbing agent in previous studies.

  5. EERE Success Story-New Tire Technologies Can Improve Fuel Efficiency by

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Than 5% | Department of Energy New Tire Technologies Can Improve Fuel Efficiency by More Than 5% EERE Success Story-New Tire Technologies Can Improve Fuel Efficiency by More Than 5% January 15, 2016 - 10:17am Addthis EERE Success Story—New Tire Technologies Can Improve Fuel Efficiency by More Than 5% EERE Success Story—New Tire Technologies Can Improve Fuel Efficiency by More Than 5% EERE Success Story-New Tire Technologies Can Improve Fuel Efficiency by More Than 5% EERE

  6. Super recycled water: quenching computers

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Super recycled water: quenching computers Super recycled water: quenching computers New facility and methods support conserving water and creating recycled products. Using reverse osmosis to "super purify" water allows the system to reuse water and cool down our powerful yet thirsty computers. January 30, 2014 Super recycled water: quenching computers LANL's Sanitary Effluent Reclamation Facility, key to reducing the Lab's discharge of liquid. Millions of gallons of industrial

  7. The use of scrap tires in rotary cement kilns

    SciTech Connect (OSTI)

    Blumenthal, M.

    1996-12-31

    The use of scrap tires as a supplemental fuel in the United States Portland cement industry has increased significantly in the past six years. In 1990, there were two kilns using tire-derived fuel (TDF), today 30 kilns use TDF. The outlook for continued and expanded use of TDF in the U.S. cement industry should be considered favorable, with 15 kilns conducting tests to determine TDF`s applicability or in the permitting process. The Council`s estimates are that by the end of 1996, the cement industry could be consuming some 75-100 million of the 253 million annually generated scrap tires in the United States. This level of TDF usage will make the cement industry the largest market segments for scrap tires in the United States. While the long-term outlook is at present positive, there are a series of factors that have, and will likely continue to adversely impact the near-term usage of TDF. These issues, as well as the factors that are likely to positively impact the cement kiln TDF market are the subject of this presentation.

  8. Demonstration of improved vehicle fuel efficiency through innovative tire design, materials, and weight reduction technologies

    SciTech Connect (OSTI)

    Donley, Tim

    2014-12-31

    Cooper completed an investigation into new tire technology using a novel approach to develop and demonstrate a new class of fuel efficient tires using innovative materials technology and tire design concepts. The objective of this work was to develop a new class of fuel efficient tires, focused on the “replacement market” that would improve overall passenger vehicle fuel efficiency by 3% while lowering the overall tire weight by 20%. A further goal of this project was to accomplish the objectives while maintaining the traction and wear performance of the control tire. This program was designed to build on what has already been accomplished in the tire industry for rolling resistance based on the knowledge and general principles developed over the past decades. Cooper’s CS4 (Figure #1) premium broadline tire was chosen as the control tire for this program. For Cooper to achieve the goals of this project, the development of multiple technologies was necessary. Six technologies were chosen that are not currently being used in the tire industry at any significant level, but that showed excellent prospects in preliminary research. This development was divided into two phases. Phase I investigated six different technologies as individual components. Phase II then took a holistic approach by combining all the technologies that showed positive results during phase one development.

  9. Method for recycling tires and similarly compounded materials to recover usable constituents

    SciTech Connect (OSTI)

    Letsch, W.

    1980-12-23

    A processing plant and method are described for processing scrap tires and similar materials containing a mixture of technical rubber, scrap metal and tire cord in which the plant is essentially vehicular and thus eliminates the necessity of hauling accumulated tires long distances with the accompanying costs. The plant includes means for directing mixed tire sizes to a cyrogenic section where the technical rubber is reduced to a sufficient temperature making it brittle so that initial separation of reusable technical rubber is accomplished; the plant is operated essentially on the reusable by-products of pyrolytic reduction of the tires so that hydrocarbons and heated gas are utilized and additional commercial by-products such as commercial soots, metal and tire beads are obtained.

  10. Numerical model for the vacuum pyrolysis of scrap tires in batch reactors

    SciTech Connect (OSTI)

    Yang, J.; Tanguy, P.A.; Roy, C.

    1995-06-01

    A quantitative model for scrap tire pyrolysis in a batch scale reactor developed comprises the following basic phenomena: conduction inside tire particles; conduction, convection, and radiation between the feedstock particles or between the fluids and the particles; tire pyrolysis reaction; exothermicity and endothermicity caused by tire decomposition and volatilization; and the variation of the composition and the thermal properties of tire particles. This model was used to predict the transient temperature and density distributions in the bed of particles, the volatile product evolution rate, the mass change, the energy consumption during the pyrolysis process, and the pressure history in a tire pyrolysis reactor with a load of 1 kg. The model predictions agree well with independent experimental data.

  11. Evaluation of synergy in tire rubber-coal coprocessing

    SciTech Connect (OSTI)

    Mastral, A.M.; Mayoral, M.C.; Murillo, R.; Callen, M.; Garcia, T.; Tejero, M.P.; Torres, N.

    1998-09-01

    The tire rubber-coal synergy is evaluated through the different roles that rubber can have in coprocessing systems. For that, two different experimental designs were used: a swept fixed-bed reactor and tubing bomb minireactors. In this way, coal was coprocessed with rubber liquids from rubber pyrolysis and rubber hydrogenation, in a hydrogen atmosphere at 400 C. Coal was mixed as well with rubber in different proportions and hydrogenated at 375, 400, and 425 C, and oils obtained were characterized by thin-layer chromatography to obtain hydrocarbon type composition. Rubber behavior was compared to each of the main components of tires, and all the results indicated that the slight synergy found can be due to the small free radicals from vulcanized rubber decomposition, which are able to stabilize coal radicals to light products.

  12. Scrap tire recycling: Promising high value applications. Final report

    SciTech Connect (OSTI)

    Bauman, B.D.; Leskovyansky, P.J.; Drela, H.

    1993-11-01

    Surface modification of scrap tire rubber (rubber particles treated with chlorine gas) show promise for ameliorating the scrap tire problem (the treated rubber can be used as a component in high- performance, expensive polymer systems). The process has been proven in Phase I. Phase II covers market/applications, process development (Forberg-design mixer reactor was chosen), plant design, capital cost estimate, economics environmental/safety/health, and energy impact. Almost of the small amount of chlorine is consumed. The capital costs for a rubber particle treatment facility are attractive, being at least two orders of magnitude less than that of facilities for making new polymer materials. Large volume markets using treated rubber are needed. The amount of scrap rubber available is small compared to the polymers available for replacement. 7 tabs, 16 figs.

  13. General Davis kicks the tires on a Safeguards Transporter | National

    National Nuclear Security Administration (NNSA)

    Nuclear Security Administration | (NNSA) General Davis kicks the tires on a Safeguards Transporter Tuesday, October 6, 2015 - 8:43am NNSA Blog Brigadier General Stephen L. Davis, NNSA's Acting Deputy Administrator for Defense Programs, gets a lesson on how to drive a Safeguards Transporter during a recent visit to the Office of Secure Transportation (OST) headquarters in Albuquerque, New Mexico. OST is responsible for transporting nuclear weapons, components and special nuclear materials to

  14. EERE Success Story-Goodyear Testing Self-Inflating Tire Systems...

    Office of Environmental Management (EM)

    new Air Maintenance Technology -- also called the self-regulating tire -- works. | Graphic courtesy of Goodyear. This graphic shows how Goodyear's new Air Maintenance Technology ...

  15. Fact #763: January 21, 2013 Eighty-four Percent of Scrapped Tires Are

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Recycled | Department of Energy 3: January 21, 2013 Eighty-four Percent of Scrapped Tires Are Recycled Fact #763: January 21, 2013 Eighty-four Percent of Scrapped Tires Are Recycled There were 263 million tires scrapped in 2009 (latest available data) which amounts to more than 4.7 million tons of waste. Fortunately, 84% of that waste was recycled. Most of the recycled tires were used to make fuel for industries such as pulp and paper mills, cement kilns, and electric utilities. Ground

  16. Characterization of chars from coal-tire copyrolysis

    SciTech Connect (OSTI)

    Mastral, A.M.; Callen, M.S.; Murillo, R.; Alvarez, R.; Clemente, C.

    1999-07-01

    The objective of this work is the characterization of the solid conversion product from coal-tire copyrolysis because, nowadays, any new process should be faced without resolving the problem of the subproducts generated. A low-rank coal and a nonspecific mixture of scrap automotive tires, 50/50 w/w, have been coprocessed at 400 C for 30 min at different H{sub 2} pressures and atmospheres. Once the most valuable conversion products, the liquids, were recovered by tetrahydrofuran extraction, a complementary battery of analytical techniques was applied to characterize the solids or chars, looking for their possible use. {sup 13}C nuclear magnetic resonance, infrared, immediate and ultimate analyses, ASA, and scanning electron microscopy-energy-dispersive X-ray spectrometry were performed on them. By X-ray diffractometry the presence of sphalerite, pyrrhotite, and anhydrite was detected. Thermogravimetric studies demonstrated that the combustion induction temperature is 400 C. Char combustion tests at 900 C with discussion of NO{sub x}, SO{sub x}, and polycyclic aromatic hydrocarbon emissions are included. Mineral matter behaves as if only coal is processed with the Zn exception, from ZnO in the tire, which is converted into ZnS. It is shown that the char organic component has a higher aromaticity than the one from coal.

  17. Vehicle Technologies Office 2013 Merit Review: A System for Automatically Maintaining Pressure in a Commercial Truck Tire

    Broader source: Energy.gov [DOE]

    A presentation given by PPG during the 2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting on a system for automatically maintaining tire pressure in commercial truck tires.

  18. SuperBulbs Inc | Open Energy Information

    Open Energy Info (EERE)

    SuperBulbs, Inc. Place: Rewood City, California Zip: 94065 Product: California-based LED manufacturer and technology developer. References: SuperBulbs, Inc.1 This article is...

  19. SuperB Progress Report: Detector

    SciTech Connect (OSTI)

    Grauges, E.; Donvito, G.; Spinoso, V.; Manghisoni, M.; Re, V.; Traversi, G.; Eigen, G.; Fehlker, D.; Helleve, L.; Carbone, A.; Di Sipio, R.; Gabrielli, A.; Galli, D.; Giorgi, F.; Marconi, U.; Perazzini, S.; Sbarra, C.; Vagnoni, V.; Valentinetti, S.; Villa, M.; Zoccoli, A.; /INFN, Bologna /Bologna U. /Caltech /Carleton U. /Cincinnati U. /INFN, CNAF /INFN, Ferrara /Ferrara U. /UC, Irvine /Taras Shevchenko U. /Orsay, LAL /LBL, Berkeley /UC, Berkeley /Frascati /INFN, Legnaro /Orsay, IPN /Maryland U. /McGill U. /INFN, Milan /Milan U. /INFN, Naples /Naples U. /Novosibirsk, IYF /INFN, Padua /Padua U. /INFN, Pavia /Pavia U. /INFN, Perugia /Perugia U. /INFN, Perugia /Caltech /INFN, Pisa /Pisa U. /Pisa, Scuola Normale Superiore /PNL, Richland /Queen Mary, U. of London /Rutherford /INFN, Rome /Rome U. /INFN, Rome2 /Rome U.,Tor Vergata /INFN, Rome3 /Rome III U. /SLAC /Tel Aviv U. /INFN, Turin /Turin U. /INFN, Padua /Trento U. /INFN, Trieste /Trieste U. /TRIUMF /British Columbia U. /Montreal U. /Victoria U.

    2012-02-14

    This report describes the present status of the detector design for SuperB. It is one of four separate progress reports that, taken collectively, describe progress made on the SuperB Project since the publication of the SuperB Conceptual Design Report in 2007 and the Proceedings of SuperB Workshop VI in Valencia in 2008.

  20. EIS-0138: Superconducting Super Collider

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy developed this EIS to analyze the potential environmental impacts of constructing the Superconducting Super Collider, a large proton accelerator, at each of seven alternative locations.

  1. Pyrolysis of scrap tires: Can it be profitable?

    SciTech Connect (OSTI)

    Wojtowicz, M.A.; Serio, M.A.

    1996-10-01

    Pyrolysis--the thermal degradation in the absence of oxygen--is one way to reprocess scrap tires. The products are fuel gas, oils, and a solid residue (char), which contains appreciable quantities of mineral matter and low-grade carbon black. The three products have comparable yields by weight. The two most important factors affecting process economics are the tipping fees charged for tire disposal and the selling prices of the products. Selling prices of the products yield low returns because of the low market value of the fuels and the low quality of the recovered char or carbon black. Therefore, to obtain a positive cash flow, it would be desirable to develop a process based on the recovery of value-added products such as high-grade carbon black, activated carbon, or valuable chemicals (e.g., benzene, toluene, and xylene). The authors believe that significant improvement in the economics can be accomplished by upgrading the primary pyrolysis products to secondary products of higher value.

  2. SuperTurbocharger | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SuperTurbocharger SuperTurbocharger Efficiency improvement, power increase, and throttle response achieved by SuperTurbocharger on a natural gas bus engine is presented. deer08_vandyne.pdf (1.09 MB) More Documents & Publications Achieving and Demonstrating Vehicle Technologies Engine Fuel Efficiency Milestones Cummins SuperTruck Program - Technology and System Level Demonstration of Highly Efficient and Clean, Diesel Powered Class 8 Trucks Cummins SuperTruck Program - Technology and System

  3. Chemi-microbial processing of waste tire rubber: A project overview

    SciTech Connect (OSTI)

    Romine, R.A.; Snowden-Swan, L.

    1993-12-01

    PNL is developing a method to use thiophillic microorganisms to devulcanize (biodesulfurize) the surface of ground rubber particles, which will improve the bonding and adhesion of the ground tire rubber into the virgin tire rubber matrix. The Chemi-microbial processing approach, introduced in this paper, is targeted at alleviating the waste tire problem in an environmentally conscious manner; it may also be applied to improve asphaltic materials and rubber and polymeric wastes to facilite their recycling. This paper outlines the logic and technical methods that will be used.

  4. Vacuum pyrolyzed tire oil as a coal solvent

    SciTech Connect (OSTI)

    Orr, E.C.; Shi, Yanlong; Ji, Qin; Anderson, L.L.; Eyring, E.M.

    1995-12-31

    Recent interest in coprocessing coal with hydrogen rich waste materials in order to produce liquid transportation fuels has given rise to interesting twists on standard coal liquefaction. In general, coprocessing coal with a waste material has been approached with the idea that the waste material would be mixed with the coal under liquefaction conditions with little or no preliminary processing of the waste material other than shredding into smaller size particles. Mixing the waste material with the coal would occur in the primary stage of liquefaction. The primary stage would accomplish the dissolution of the coal and breakdown of the waste material. The products would then be introduced into the secondary stage where upgrading of product would occur. This paper describes the usefulness of oil derived from pyrolysis of waste rubber tires as a reactant in coal coprocessing or coal liquefaction.

  5. Optimization of scrap tire pyrolysis using a continuous-feed steam environment

    SciTech Connect (OSTI)

    Burrell, T.W.; Frank, S.R.; Rich, M.L.

    1995-12-01

    Estimates of the generation of scrap tires produced in the United States are on the order of 2 million tons per year. Although these tires contain a high percentage of useful hydrocarbons, steel and carbon black, approximately 70% are not effectively recycled. Recently, pyrolytic recycling of scrap tire (thermal decomposition in the absence of O{sub 2}) is receiving renewed interest because of its ability to produce valuable hydrocarbon products. We have developed a process which permits a continuous feed processing of scrap tires in a non-combustible stream environment. This system utilizes a soft seal system that operates at atmospheric pressures while minimizing any fugitive emissions. This process increases the efficiency and control of present approaches by lowering the energy requirements while maximizing the collection of valuable products. Initial bench-scale results will be presented.

  6. Pyrolysis of scrap tires and conversion of chars to activated carbon

    SciTech Connect (OSTI)

    Merchant, A.A.; Petrich, M.A. . Dept. of Chemical Engineering)

    1993-08-01

    The primary objective of this work was to demonstrate the conversion of scrap tires to activated carbon. The authors have been successful in this endeavor, producing carbons with surface areas greater than 500 m[sup 2]/g and significant micropore volumes. Tire shreddings were pyrolyzed in batch reactors, and the pyrolysis chars activated by reaction with superheated steam. Solid products of pyrolysis and activation were studied with nitrogen adsorption techniques. They find that the porosity development during steam activation of tire pyrolysis char is similar to that reported for various other chars. A maximum in micropore volume is observed as a function of conversion, but the total surface area increases monotonically with conversion. They suggest that the activation process consists of micropore formation, followed by pore enlargement. The process conditions used in this study are a good starting point from which to optimize a process to convert tires to activated carbon.

  7. Formation of dl-limonene in used tire vacuum pyrolysis oils. [dipentene

    SciTech Connect (OSTI)

    Pakdel, H.; Roy, C.; Aubin, H.; Jean, G. ); Coulombe, S. )

    1991-09-01

    Tire recycling has become an important environmental issue recently due to the huge piles of tires that threaten the environment. Thermal decomposition of tire, a synthetic rubber material, enables the recovery of carbon black and liquid hydrocarbon oils. Both have potential economic values. Pyrolysis oils obtained under vacuum conditions contain a significant portion of a volatile, naptha-like fraction with an octane number similar to petroleum naphtha fraction, in addition, contains approximately 15% limonene. Potential applications of vacuum pyrolysis oil and carbon black have been investigated. However, the process economics is greatly influenced by the quality of the oil and carbon black products. This paper discusses limonene formation during used tire vacuum pyrolysis and its postulated reaction mechanism. The limonene separation method from pyrolysis oil, as well as its purification in laboratory scale, and structural characterization are discussed. Large-scale limonene separation and purification is under investigation.

  8. Fact #826: June 23, 2014 The Effect of Tire Pressure on Fuel Economy

    Broader source: Energy.gov [DOE]

    Researchers at Oak Ridge National Laboratory recently conducted a study that measured the effect of tire pressure on fuel economy at speeds ranging from 40 to 80 miles per hour. The figure below...

  9. Goodyear Tire Plant Gains Traction on Energy Savings After Completing Save Energy Now Assessment

    Broader source: Energy.gov [DOE]

    is case study describes how the Goodyear Tire Plant saved approximately 93,000 MMBtu and $875,000 annually after increasing steam system energy efficiency in their Union City, Tennessee, plant.

  10. EERE Success Story-New Tire Technologies Can Improve Fuel Efficiency...

    Office of Environmental Management (EM)

    tires that can improve fuel efficiency by 5.5%, supported by a project from the EERE Vehicle Technologies Office (VTO). ... Licensed for Use in Fuel Cell Hybrid Advanced Vehicles ...

  11. Goodyear Testing Self-Inflating Tire Systems in U.S. Trucking...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    fuel economy 2-3 percent, this innovative technology will help save nearly 1.2 billion gallons of petroleum that experts estimate are wasted each year due to underinflated tires. ...

  12. Vacuum pyrolysis of waste tires with basic additives

    SciTech Connect (OSTI)

    Zhang Xinghua; Wang Tiejun Ma Longlong; Chang Jie

    2008-11-15

    Granules of waste tires were pyrolyzed under vacuum (3.5-10 kPa) conditions, and the effects of temperature and basic additives (Na{sub 2}CO{sub 3}, NaOH) on the properties of pyrolysis were thoroughly investigated. It was obvious that with or without basic additives, pyrolysis oil yield increased gradually to a maximum and subsequently decreased with a temperature increase from 450 deg. C to 600 deg. C, irrespective of the addition of basic additives to the reactor. The addition of NaOH facilitated pyrolysis dramatically, as a maximal pyrolysis oil yield of about 48 wt% was achieved at 550 deg. C without the addition of basic additives, while a maximal pyrolysis oil yield of about 50 wt% was achieved at 480 deg. C by adding 3 wt% (w/w, powder/waste tire granules) of NaOH powder. The composition analysis of pyrolytic naphtha (i.b.p. (initial boiling point) {approx}205 deg. C) distilled from pyrolysis oil showed that more dl-limonene was obtained with basic additives and the maximal content of dl-limonene in pyrolysis oil was 12.39 wt%, which is a valuable and widely-used fine chemical. However, no improvement in pyrolysis was observed with Na{sub 2}CO{sub 3} addition. Pyrolysis gas was mainly composed of H{sub 2}, CO, CH{sub 4}, CO{sub 2}, C{sub 2}H{sub 4} and C{sub 2}H{sub 6}. Pyrolytic char had a surface area comparable to commercial carbon black, but its proportion of ash (above 11.5 wt%) was much higher.

  13. SOWFA + Super Controller User's Manual

    SciTech Connect (OSTI)

    Fleming, P.; Gebraad, P.; Churchfield, M.; Lee, S.; Johnson, K.; Michalakes, J.; van Wingerden, J. W.; Moriarty, P.

    2013-08-01

    SOWFA + Super Controller is a modification of the NREL's SOWFA tool which allows for a user to apply multiturbine or centralized wind plant control algorithms within the high-fidelity SOWFA simulation environment. The tool is currently a branch of the main SOWFA program, but will one day will be merged into a single version. This manual introduces the tool and provides examples such that a user can implement their own super controller and set up and run simulations. The manual only discusses enough about SOWFA itself to allow for the customization of controllers and running of simulations, and details of SOWFA itself are reported elsewhere Churchfield and Lee (2013); Churchfield et al. (2012). SOWFA + Super Controller, and this manual, are in alpha mode.

  14. Microsoft Word - Final Scientific - Technical Report_DE-EE0005390_Cooper_Tire_Submitted

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Final Scientific/Technical Report Federal Agency: U.S. DOE/NETL Award No.: DE-EE0005390 Project Title: Demonstration of improved vehicle fuel efficiency through innovative tire design, materials, and weight reduction technologies PD/PI: Tim Donley, Lead Engineer Consortium/Teaming Members: NREL tmdonley@coopertire.com Phone: 419-429-7229 Submission Date: March 31, 2015 DUNS Number: 005037601 Recipient Organization: Cooper Tire & Rubber Company 701 Lima Ave. Findlay, OH 45840 Project/Grant

  15. Improving Vehicle Fuel Efficiency Through Tire Design, Materials, and Reduced Weight

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Vehicle Fuel Efficiency Through Tire Design, Materials, and Reduced Weight PI: Tim Donley Cooper Tire & Rubber Company June 19, 2014 This presentation does not contain any proprietary, confidential, or otherwise restricted information. Project ID: VSS083 Overview Timeline * Project start date: Oct. 1, 2011 * Project end date: Sept. 30, 2014 * Project complete: 85% Barriers 1) Cost / Premium Product 2) Manufacturability Budget * Total project funding: $3,679,309 - DOE share: $1,500,000 -

  16. SECTION III

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    West Virginia Smart Grid Implementation Plan Revision 1 August 20, 2009 DOE/NETL-2009/1386 West Virginia Smart Grid Implementation Plan 20 August 2009 Revision 1 Submitted to: The Honorable Joe Manchin III, Governor, State of West Virginia Submitted by: West Virginia Division of Energy National Energy Technology Laboratory US DOE Office of Electricity Delivery and Energy Reliability Research and Development Solutions (RDS) Allegheny Power American Electric Power West Virginia University

  17. PART III

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Contract No. DE-AC02-09CH11466 Section J TOC i PART III List of Documents, Exhibits and Other Attachments Section J - List of Attachments Table of Contents Attachment No: Attachment: J.1 Appendix A - Advance Understandings on Human Resources J.2 Appendix B - Performance and Evaluation Measurement Plan J.3 Appendix C - Special Financial Institution Account Agreement J.4 Appendix D - Budget Program J.5 Appendix E - PPPL DOE (Lessee) Ingrants J.6 Appendix F - Contractor Resources, Commitments and

  18. SuperNEMO Project Status

    SciTech Connect (OSTI)

    Chauveau, E. [Universite de Bordeaux, Centre d'Etudes Nucleaires de Bordeaux Gradignan, UMR 5797, F-33175 Gradignan (France) and CNRS/IN2P3, Centre d'Etudes Nucleaires de Bordeaux Gradignan, UMR 5797, F-33175 Gradignan (France)

    2009-11-09

    The SuperNEMO experiment aims to reach a sensitivity up to 10{sup 26} years on the half-life of neutrinoless double beta decay. The chosen way is to build a 'tracko-calo' detector with at least 100 kg of betabeta isotope. The current status of the main R and D tasks will be presented: enrichment and production of source foil, radiopurity control, tracker and calorimeter.

  19. Pyrolysis kinetics of scrap tire rubbers. 1: Using DTG and TGA

    SciTech Connect (OSTI)

    Kim, S.; Park, J.K.; Chun, H.D.

    1995-07-01

    Tire pyrolysis kinetics was investigated to explore an economically viable design for the pyrolysis process. Derivative thermogravimetry (DTG) and thermogravimetric analysis (TGA) were found to provide valuable information on pyrolysis kinetics and mechanisms of a heterogeneous compound like scrap tire rubbers. Kinetic parameters of each compositional compound were obtained by analyzing DTG and TGA results with a series of mathematical methods proposed in this study. The pyrolysis kinetics of the scrap tire rubbers tested was well accounted for by the first-order irreversible independent reactions of three compositional compounds. The sidewall and tread rubber exhibited different thermal degradation patterns, suggesting a compositional difference between them. Isothermal pyrolysis results showed that the sidewall rubber would hardly be degraded at low temperature regions (<600 K), whereas it would be more rapidly degraded than the tread rubber at higher temperatures ({>=}746 K). Because of the shorter pyrolysis time, the higher isothermal pyrolysis temperature appeared to be more economically favorable.

  20. Evaluation of products recovered from scrap tires for use as asphalt modifiers

    SciTech Connect (OSTI)

    McKay, J.

    1992-05-01

    Western Research Institute performed rheological tests and water sensitivity tests on asphalt cements that had been modified with carbonous residues obtained from the pyrolysis of scrap tires and waste motor oil. These tests are part of an ongoing program at the University of Wyoming Chemical Engineering Department to evaluate, as asphalt additives, solid carbonous products recovered from the scrap tire and waste motor oil pyrolysis experiments conducted at the University. The tests showed that carbonous residues increased the viscosity and decreased the elasticity of AC-10 and AC-20 asphalts. The tests also indicatedthat asphalt cements modified with carbonous residues were less sensitive to water damage and age embrittlement than unmodified asphalt cements.

  1. Extraction and identification of fillers and pigments from pyrolyzed rubber and tire samples

    SciTech Connect (OSTI)

    Sadhukhan, P.; Zimmerman, J.B.

    1996-12-31

    Rubber stocks, specially tires, are composed of natural rubber and synthetic polymers and also of several compounding ingredients, such as carbon black, silica, zinc oxide etc. These are generally mixed and vulcanized with additional curing agents, mainly organic in nature, to achieve certain {open_quotes}designing properties{close_quotes} including wear, traction, rolling resistance and handling of tires. Considerable importance is, therefore, attached both by the manufacturers and their competitors to be able to extract, identify and characterize various types of fillers and pigments. Several analytical procedures have been in use to extract, preferentially, these fillers and pigments and subsequently identify and characterize them under a transmission electron microscope.

  2. Super Wi-Fi is Super for Energy Too | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Wi-Fi is Super for Energy Too Super Wi-Fi is Super for Energy Too September 24, 2010 - 11:45am Addthis Super Wi-Fi is Super for Energy Too Nick Sinai U.S. Deputy Chief Technology Officer, White House Office of Science and Technology Policy What does this mean for me? By integrating broadband into the emerging Smart Grid, consumers will have revolutionized communication with their utility -- they will have detailed information on their energy use that will help inform them how they can save on

  3. Tailored Recovery of Carbons from Waste Tires for Enhanced Performance as Anodes in Lithium-ion Batteries

    SciTech Connect (OSTI)

    Naskar, Amit K; Bi,; Saha, Dipendu; Chi, Miaofang; Bridges, Craig A; Paranthaman, Mariappan Parans

    2014-01-01

    Morphologically tailored pyrolysis-recovered carbon black is utilized in lithium-ion batteries as a potential solution for adding value to waste tire-rubber-derived materials. Micronized tire rubber was digested in a hot oleum bath to yield a sulfonated rubber slurry that was then filtered, washed, and compressed into a solid cake. Carbon was recovered from the modified rubber cake by pyrolysis in a nitrogen atmosphere. The chemical pretreatment of rubber produced a carbon monolith with higher yield than that from the control (a fluffy tire-rubber-derived carbon black). The carbon monolith showed a very small volume fraction of pores of widths 3 4 nm, reduced specific surface area, and an ordered assembly of graphitic domains. Electrochemical studies on the recovered-carbon-based anode revealed an improved Li-ion battery performance with higher reversible capacity than that of commercial carbon materials. Anodes made with a sulfonated tire-rubber-derived carbon and a control tire-rubber-derived carbon, respectively, exhibited an initial coulombic efficiency of 80% and 45%, respectively. The reversible capacity of the cell with the sulfonated carbon as anode was 400 mAh/g after 100 cycles, with nearly 100% coulombic efficiency. Our success in producing higher performance carbon material from waste tire rubber for potential use in energy storage applications adds a new avenue to tire rubber recycling.

  4. Tire-derived carbon composite anodes for sodium-ion batteries

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Li, Yunchao; Paranthaman, M. Parans; Akato, Kokouvi; Naskar, Amit K.; Levine, Alan M.; Lee, Richard J.; Kim, Sang-Ok; Zhang, Jinshui; Dai, Sheng; Manthiram, Arumugam

    2016-04-04

    We report that hard-carbon materials are considered as one of the most promising anodes for the emerging sodium-ion batteries. Here, we report a low-cost, scalable waste tire-derived carbon as an anode for sodium-ion batteries (SIBs). The tire-derived carbons obtained by pyrolyzing the acid-treated tire at 1100 °C, 1400 °C and 1600 °C show capacities of 179, 185 and 203 mAh g-1, respectively, after 100 cycles at a current density of 20 mA g-1 in sodium-ion batteries with good electrochemical stability. The portion of the low-voltage plateau region in the charge-discharge curves increases as the heat-treatment temperature increases. The low-voltage plateaumore » is beneficial to enhance the energy density of the full cell. However, this plateau suffers rapid capacity fade at higher current densities. This study provides a new pathway for inexpensive, environmentally benign and value-added waste tire-derived products towards large-scale energy storage applications.« less

  5. Volvo SuperTruck - Powertrain Technologies for Efficiency Improvement...

    Broader source: Energy.gov (indexed) [DOE]

    More Documents & Publications Volvo SuperTruck - Powertrain Technologies for Efficiency Improvement Vehicle Technologies Office Merit Review 2015: Volvo SuperTruck - Powertrain ...

  6. Vehicle Technologies Office Merit Review 2015: Cummins SuperTruck...

    Broader source: Energy.gov (indexed) [DOE]

    Peer Evaluation Meeting about Cummins SuperTruck program technology and system level ... Vehicle Technologies Office Merit Review 2015: Volvo SuperTruck - Powertrain Technologies ...

  7. Super- and sub-Einstein intrinsic viscosities of spherical nanoparticl...

    Office of Scientific and Technical Information (OSTI)

    Super- and sub-Einstein intrinsic viscosities of spherical nanoparticles in concentrated low molecular weight polymer solutions Citation Details In-Document Search Title: Super- ...

  8. Evaluation of the Super ESPC Program: Level 2 -- Recalculated...

    Office of Scientific and Technical Information (OSTI)

    Management Program's Super Energy Savings Performance Contract (Super ESPC) Program. ... that are established in the project contract as those to be used by the ESCO to ...

  9. Vehicle Technologies Office Merit Review 2015: Volvo SuperTruck...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SuperTruck - Powertrain Technologies for Efficiency Improvement Vehicle Technologies Office Merit Review 2015: Volvo SuperTruck - Powertrain Technologies for Efficiency Improvement...

  10. Ending Aging in Super Glassy Polymer Membranes

    SciTech Connect (OSTI)

    Lau, CH; Nguyen, PT; Hill, MR; Thornton, AW; Konstas, K; Doherty, CM; Mulder, RJ; Bourgeois, L; Liu, ACY; Sprouster, DJ; Sullivan, JP; Bastow, TJ; Hill, AJ; Gin, DL; Noble, RD

    2014-04-16

    Aging in super glassy polymers such as poly(trimethylsilylpropyne) (PTMSP), poly(4-methyl-2-pentyne) (PMP), and polymers with intrinsic microporosity (PIM-1) reduces gas permeabilities and limits their application as gas-separation membranes. While super glassy polymers are initially very porous, and ultra-permeable, they quickly pack into a denser phase becoming less porous and permeable. This age-old problem has been solved by adding an ultraporous additive that maintains the low density, porous, initial stage of super glassy polymers through absorbing a portion of the polymer chains within its pores thereby holding the chains in their open position. This result is the first time that aging in super glassy polymers is inhibited whilst maintaining enhanced CO2 permeability for one year and improving CO2/N-2 selectivity. This approach could allow super glassy polymers to be revisited for commercial application in gas separations.

  11. SuperTruck Team Achieves 115% Freight Efficiency Improvement...

    Energy Savers [EERE]

    low-rolling resistance tires, a long-haul hybrid system, and engine waste heat recovery. Many of the technologies build on VTO's research in a number of areas such as...

  12. Vehicle Technologies Office Merit Review 2014: Improving Vehicle Fuel Efficiency Through Tire Design, Materials, and Reduced Weight

    Broader source: Energy.gov [DOE]

    Presentation given by Cooper Tire at 2014 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about improving vehicle fuel efficiency...

  13. SuperB Progress Report for Physics

    SciTech Connect (OSTI)

    O'Leary, B.; Matias, J.; Ramon, M.; Pous, E.; De Fazio, F.; Palano, A.; Eigen, G.; Asgeirsson, D.; Cheng, C.H.; Chivukula, A.; Echenard, B.; Hitlin, D.G.; Porter, F.; Rakitin, A.; Heinemeyer, S.; McElrath, B.; Andreassen, R.; Meadows, B.; Sokoloff, M.; Blanke, M.; Lesiak, T.; /Cracow, INP /DESY /Zurich, ETH /INFN, Ferrara /Frascati /INFN, Genoa /Glasgow U. /Indiana U. /Mainz U., Inst. Phys. /Karlsruhe, Inst. Technol. /KEK, Tsukuba /LBL, Berkeley /UC, Berkeley /Lisbon, IST /Ljubljana U. /Madrid, Autonoma U. /Maryland U. /MIT /INFN, Milan /McGill U. /Munich, Tech. U. /Notre Dame U. /PNL, Richland /INFN, Padua /Paris U., VI-VII /Orsay, LAL /Orsay, LPT /INFN, Pavia /INFN, Perugia /INFN, Pisa /Queen Mary, U. of London /Regensburg U. /Republica U., Montevideo /Frascati /INFN, Rome /INFN, Rome /INFN, Rome /Rutherford /Sassari U. /Siegen U. /SLAC /Southern Methodist U. /Tel Aviv U. /Tohoku U. /INFN, Turin /INFN, Trieste /Uppsala U. /Valencia U., IFIC /Victoria U. /Wayne State U. /Wisconsin U., Madison

    2012-02-14

    SuperB is a high luminosity e{sup +}e{sup -} collider that will be able to indirectly probe new physics at energy scales far beyond the reach of any man made accelerator planned or in existence. Just as detailed understanding of the Standard Model of particle physics was developed from stringent constraints imposed by flavour changing processes between quarks, the detailed structure of any new physics is severely constrained by flavour processes. In order to elucidate this structure it is necessary to perform a number of complementary studies of a set of golden channels. With these measurements in hand, the pattern of deviations from the Standard Model behavior can be used as a test of the structure of new physics. If new physics is found at the LHC, then the many golden measurements from SuperB will help decode the subtle nature of the new physics. However if no new particles are found at the LHC, SuperB will be able to search for new physics at energy scales up to 10-100 TeV. In either scenario, flavour physics measurements that can be made at SuperB play a pivotal role in understanding the nature of physics beyond the Standard Model. Examples for using the interplay between measurements to discriminate New Physics models are discussed in this document. SuperB is a Super Flavour Factory, in addition to studying large samples of B{sub u,d,s}, D and {tau} decays, SuperB has a broad physics programme that includes spectroscopy both in terms of the Standard Model and exotica, and precision measurements of sin{sup 2} {theta}{sub W}. In addition to performing CP violation measurements at the {Upsilon}(4S) and {phi}(3770), SuperB will test CPT in these systems, and lepton universality in a number of different processes. The multitude of rare decay measurements possible at SuperB can be used to constrain scenarios of physics beyond the Standard Model. In terms of other precision tests of the Standard Model, this experiment will be able to perform precision over

  14. DOE Subpoenas Maker of Super Power Showerhead

    Broader source: Energy.gov [DOE]

    Yesterday, the Department of Energy’s Office of Enforcement issued a subpoena to Richard Graham of Long Beach, California seeking water efficiency information and sales records for the “Super Power...

  15. Wave transmission and mooring-force characteristics of pipe-tire floating breakwaters

    SciTech Connect (OSTI)

    Harms, Volker W.; Westerink, Joannes J.

    1980-10-01

    The results are presented of a series of prototype scale tests of a floating breakwater that incorporates massive cylindrical members (steel or concrete pipes, telephone poles, etc.) in a matrix of scrap truck or automobile tires, referred to as the Pipe-Tire Breakwater (PT-Breakwater). Tests were conducted in the large wave tank at the US Army Coastal Engineering Research Center (CERC). Breakwater modules were preassembled at SUNY in Buffalo, New York, and then transported to CERC by truck, where final assembly on location was again performed by SUNY personnel. Wave-tank tests were conducted jointly by CERC and SUNY personnel. A series of wave-tank experiments and mooring system load-deflection tests were performed, and are described. Wave-transmission and mooring-load characteristics, based on 402 separate tests, were established and are reported. (LCL)

  16. SUPER-B LATTICE STUDIES

    SciTech Connect (OSTI)

    Biagini, M.E.; Raimondi, P.; Piminov, P.; Sinyatkin, S.; Nosochkov, Y.; Wittmer, W.; /SLAC

    2010-08-25

    The SuperB asymmetric e{sup +}e{sup -} collider is designed for 10{sup 36} cm{sup -2} s{sup -1} luminosity and beam energies of 6.7 and 4.18 GeV for e{sup +} and e{sup -} respectively. The High and Low Energy Rings (HER and LER) have one Interaction Point (IP) with 66 mrad crossing angle. The 1258 m rings fit to the INFN-LNF site at Frascati. The ring emittance is minimized for the high luminosity. The Final Focus (FF) chromaticity correction is optimized for maximum transverse acceptance and energy bandwidth. Included Crab Waist sextupoles suppress betatron resonances induced in the collisions with a large Piwinski angle. The LER Spin Rotator sections provide longitudinally polarized electron beam at the IP. The lattice is flexible for tuning the machine parameters and compatible with reusing the PEP-II magnets, RF cavities and other components. Details of the lattice design are presented.

  17. Super-B Project Overview

    SciTech Connect (OSTI)

    Biagini, M.E.; Boni, R.; Boscolo, M.; Demma, T.; Drago, A.; Guiducci, S.; Raimondi, P.; Tomassini, S.; Zobov, M.; Bertsche, K.; Donald, M.; Nosochkov, Y.; Novokhatski, A.; Seeman, J.; Sullivan, M.; Yocky, G.; Wienands, U.; Wittmer, W.; Koop, I.; Levichev, E.; Nikitin, S.; /Novosibirsk, IYF /KEK, Tsukuba /Pisa U. /CERN

    2010-08-26

    The SuperB project aims at the construction of an asymmetric very high luminosity B-Factory on the Frascati/Tor Vergata (Italy) area, providing a uniquely sensitive probe of New Physics in the flavour sector of the Standard Model. The luminosity goal of 10{sup 36} cm{sup -2} s{sup -1} can be reached with a new collision scheme with 'large Piwinski angle' (LPA) and the use of 'crab waist sextupoles' (CW). A LPA&CW Interaction Region (IR) has been successfully tested at the DA{Phi}NE {Phi}-Factory at LNF-Frascati in 2008. The LPA&CW scheme, together with very low {beta}*, will allow for operation with relatively low beam currents and reasonable bunch length, comparable to those of PEP-II and KEKB. In the High Energy Ring (HER), two spin rotators will bring longitudinally polarized beams into collision at the IP. The lattice has been designed with a very low intrinsic emittance and is quite compact, less than 2 km long. The tight focusing requires the final doublet quadrupoles to be very close to the IP and very compact. A Conceptual Design Report was published in March 2007, and beam dynamics and collective effects R&D studies are in progress in order to publish a Technical Design Report by the end of 2010.

  18. Thermal plasma pyrolysis of used old tires for production of syngas

    SciTech Connect (OSTI)

    Chang, J.S.; Gu, B.W.; Looy, P.C.; Chu, F.Y.; Simpson, C.J.

    1996-08-01

    Thermal plasma pyrolysis of used tires for the production of syngaswas investigated experimentally and the following conclusions wereobtained: 1. A series of experiments have shown that tire waste can bepyrolyzed in a plasma reactor to produce combustible gas, such asC{sub 2}H{sub 2}, CH{sub 4}, C{sub 2}H{sub 4}, H{sub 2}, CO. The combustion heat value of the produced gas is about 4-7 MJ/m{sup 3}, which is higher than that of blast furnace gas and reforming gas from coals. 2. Zinc oxidecan be captured during pyrolysis by both high temperature filters andlow temperature filters in the quenching chamber. The pollution gases,such as SO{sub 2} and NO{sub x}, are at relatively low levels, about 100-300ppm. 3. Increasing the tire injection quantity will increase theconcentration of hydrocarbons, increase the combustion heat of thepyrolysis product, and decrease the concentration of metal oxide. Withsteam injection, it produced a large quantity of hydrogen and carbonmonoxide with lower concentrations of C{sub 2}H{sub 2}. The combustion heatis slightly lower with steam injection than that without it. 4. Neitherpolychlorinated biphenyls (PCBs) nor p-aminohippuric acid (PAH) weredetected in the ashes. 8 refs., 11 figs., 4 tabs.

  19. WCI-III

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    WCI-III Texas A&M University College Station, TX February 12-16, 2005 WCI-III Steering Committee Philippe Chomaz Francesca Gulminelli Joe Natowitz Sherry Yennello

  20. Searching for New Physics at SuperB - The Super Flavor Factory

    ScienceCinema (OSTI)

    Hiltin, David [Caltech, Pasadena, California, United States

    2010-01-08

    SuperB ? a Super Flavor Factory, an electron-positron collider with a luminosity of 1036 cm-2 s-1, can conduct conduct unique sensitive searches for New Physics effects such as lepton flavor violation and new sources of CP violation in the quark and lepton sectors.

  1. Ashtabula III | Open Energy Information

    Open Energy Info (EERE)

    III Jump to: navigation, search Name Ashtabula III Facility Ashtabula III Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Developer NextEra Energy...

  2. Background considerations for SuperCDMS

    SciTech Connect (OSTI)

    Cooley, J.; Collaboration: SuperCDMS Collaboration

    2013-08-08

    Rejection and protection from background is a key issue for the next generation SuperCDMS SNOLAB experiment that will have a cross-section sensitivity of better than 8 × 10{sup −46} cm{sup 2} for spin-independent WIMP-nucleon interactions. This paper presents the details of the methods used to reject electromagnetic backgrounds using the new iZIP detectors that are currently operated in the Soudan Underground Laboratory, MN and the methods the collaboration is investigating to protect against neutron background in the next generation SuperCDMS experiment.

  3. Super-collimation by axisymmetric photonic crystals

    SciTech Connect (OSTI)

    Purlys, V.; Gailevi?ius, D.; Peckus, M.; Gadonas, R.; Maigyte, L.; Staliunas, K.

    2014-06-02

    We propose and experimentally show the mechanism of beam super-collimation by axisymmetric photonic crystals, specifically by periodic (in propagation direction) structure of layers of concentric rings. The physical mechanism behind the effect is an inverse scattering cascade of diffracted wave components back into on- and near-axis angular field components, resulting in substantial enhancement of intensity of these components. We explore the super-collimation by numerical calculations and prove it experimentally. We demonstrate experimentally the axial field enhancement up to 7 times in terms of field intensity.

  4. Vehicle Technologies Office Merit Review 2014: SuperTruck Program...

    Broader source: Energy.gov (indexed) [DOE]

    about SuperTruck Program: Engine Project Review. ace058singh2014o.pdf (1.9 MB) More Documents & Publications Vehicle Technologies Office Merit Review 2015: SuperTruck ...

  5. Vehicle Technologies Office Merit Review 2015: Volvo SuperTruck...

    Energy Savers [EERE]

    Volvo SuperTruck Vehicle Technologies Office Merit Review 2015: Volvo SuperTruck Presentation given by Volvo Trucks at 2015 DOE Hydrogen and Fuel Cells Program and Vehicle ...

  6. Vehicle Technologies Office Merit Review 2015: SuperTruck Program...

    Broader source: Energy.gov (indexed) [DOE]

    about SuperTruck program: engine project review. ace058singh2015o.pdf (2.57 MB) More Documents & Publications Vehicle Technologies Office Merit Review 2014: SuperTruck ...

  7. Super Energy Saver Heat Pump - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Find More Like This Return to Search Super Energy Saver Heat Pump Oak Ridge National ... and coupled them to residential heat pumps, inventing a super energy saver heat pump. ...

  8. Top-secret super-secure vault declassified

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Top-secret super-secure vault declassified Top-secret super-secure vault declassified Located in Los Alamos canyon at Technical Area 41, the Tunnel Vault was built between 1948 and ...

  9. Super Duty Diesel Truck with NOx Aftertreatment | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Super Duty Diesel Truck with NOx Aftertreatment Super Duty Diesel Truck with NOx Aftertreatment A profile of a Ford-Energy Department program to develop a three-stage aftertreatment technology, which cleans the vehicle exhaust emissions. This profile is part of the U.S. Drive 2011 Accomplishment Report. U.S. DRIVE Highlights of Technical Accomplishments 2011: Super Duty Diesel Truck with NOx Aftertreatment (246.82 KB) More Documents & Publications Development of the 2011MY Ford Super Duty

  10. Super Truck -- 50% Improvement In Class 8 Freight Efficiency | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Super Truck -- 50% Improvement In Class 8 Freight Efficiency Super Truck -- 50% Improvement In Class 8 Freight Efficiency Presents first year highlights from Detroit Diesel Corporation and Daimler Trucks, NA joint SuperTruck engine and vehicle project to demonstrate a 50 percent freight efficiency improvement deer11_sisken.pdf (2.17 MB) More Documents & Publications Super Truck Program: Engine Project Review High-Efficiency Engine Technologies Session Introduction Roadmapping

  11. Volvo Super Truck Overview and Approach | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Volvo Super Truck Overview and Approach Volvo Super Truck Overview and Approach Provides overview and discusses approach of the Volvo Super Truck Team to develop a number of advanced technologies to significantly improve freight efficiency of long-haul trucks deer11_amar.pdf (936.68 KB) More Documents & Publications Impact of Vehicle Efficiency Improvements on Powertrain Design Vehicle Technologies Office Merit Review 2016: Volvo SuperTruck - Powertrain Technologies for Efficiency

  12. III-Nitride Nanowires

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy Frontier Research Centers: Solid-State Lighting Science Center for Frontiers of ... III-Nitride Nanowires HomeEnergy ResearchEFRCsSolid-State Lighting Science EFRC...

  13. SECTION III: NUCLEAR THEORY

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the phase-space integral ...III-1 I. S. Towner and J. C. Hardy The evaluation of V ud , experiment and theory ......

  14. DOE, Texas settle super(conducting) differences

    SciTech Connect (OSTI)

    Crawford, M.

    1994-08-02

    The US DOE agreed to pay over $200 million in cash and transfer $510 million in property to Texas to settle the state`s claims against the federal government for cancellation of the Superconducting Super Collider. This article discusses the settlement and its history and what will be done with the facilities.

  15. Waste tire derived carbon-polymer composite paper as pseudocapacitive electrode with long cycle life

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Boota, M.; Paranthaman, Mariappan Parans; Naskar, Amit K.; Gogotsi, Yury; Li, Yunchao; Akato, Kokouvi

    2015-09-25

    Recycling hazardous wastes to produce value-added products is becoming essential for the sustainable progress of our society. Herein, highly porous carbon (1625 m2/g–1) is synthesized using waste tires as the precursor and used as supercapacitor electrode. The narrow pore size distribution (PSD) and high surface area led to a good charge storage capacity, especially when used as a three-dimensional nanoscaffold to polymerize polyaniline (PANI/TC). The composite film was highly flexible, conductive and exhibited a capacitance of 480 F/g–1 at 1 mV/s–1 with excellent capacitance retention up to 98% after 10,000 charge/discharge cycles. The high capacitance and long cycle life weremore » ascribed to the short diffusional paths, uniform PANI coating and tight confinement of the PANI in the inner pores of the tire-derived carbon via - interactions, which minimized the degradation of the PANI upon cycling. Here, we anticipate that the same strategy can be applied to deposit other pseudocapacitive materials with low-cost TC to achieve even higher electrochemical performance and longer cycle life, a key challenge for redox active polymers.« less

  16. Pyrolysis of tire rubber: Porosity and adsorption characteristics of the pyrolytic chars

    SciTech Connect (OSTI)

    Miguel, G.S.; Fowler, G.D.; Sollars, C.J.

    1998-06-01

    Tire rubber has been pyrolyzed at various temperatures under a nitrogen atmosphere. The resulting chars have been analyzed for their porosity using nitrogen gas adsorption and for their aqueous adsorption characteristics using phenol, methylene blue, and the reactive dyes Procion Turquoise H-A and Procion Red H-E3B. Nitrogen adsorption isotherms were modeled to the BET and Dubinin-Astakhov (DA) equations to determine effective surface areas, mesopore volumes, and micropore volumes. Results showed that pyrolysis of tire rubber was essentially complete at 500 C and resulted in a char yield of approximately 42 wt%. Pyrolytic chars exhibited BET surface areas up to 85 m{sup 2}/g and micropore volumes up to 0.04 mL/g. Owing to their poorly developed micropore structure, the pyrolytic chars exhibited limited aqueous adsorption capacity for compounds of small molecular weight, such as phenol. However, the chars possessed significantly greater adsorption capacity for species of large molecular weight which was attributed to the presence of large mesopore volumes (up to 0.19 mL/g).

  17. Reduction of carbon content in waste-tire combustion ashes by bio-thermal treatment

    SciTech Connect (OSTI)

    Chen, C.C.; Lee, W.J.; Shih, S.I.; Mou, J.L.

    2009-07-01

    Application of bio-catalyst (NOE-7F) in thermal treatment can adequately dispose dark-black fly ashes from co-combustion of both waste tires and coal. After thermal treatment of fly ashes by adding 10% NOE-7F, the carbon contents reduced by 37.6% and the weight losses increased by 405%, compared with the fly ashes without mixing with NOE-7F. The combustion behaviors of wasted tires combustion fly ashes with NOE-7F were also investigated by both thermogravimetric analysis (TGA) and differential thermal analysis (DTA). The results verify that NOE-7F has positive effects on the combustion of residual carbon and toxic polycyclic aromatic hydrocarbons (PAHs) enhance the energy release and reduce the toxicity during the process of thermal treatment. Furthermore, using NOE-7F to dispose high-carbon content fly ashes did improve the compressive strength of fly ashes and concrete mixtures. Therefore, NOE-7F is a promising additive which could decrease treatment cost of high-carbon content fly ashes and reduce the amount of survival toxic PAHs.

  18. Waste tire derived carbon-polymer composite paper as pseudocapacitive electrode with long cycle life

    SciTech Connect (OSTI)

    Boota, M.; Paranthaman, Mariappan Parans; Naskar, Amit K.; Gogotsi, Yury; Li, Yunchao; Akato, Kokouvi

    2015-09-25

    Recycling hazardous wastes to produce value-added products is becoming essential for the sustainable progress of our society. Herein, highly porous carbon (1625 m2/g–1) is synthesized using waste tires as the precursor and used as supercapacitor electrode. The narrow pore size distribution (PSD) and high surface area led to a good charge storage capacity, especially when used as a three-dimensional nanoscaffold to polymerize polyaniline (PANI/TC). The composite film was highly flexible, conductive and exhibited a capacitance of 480 F/g–1 at 1 mV/s–1 with excellent capacitance retention up to 98% after 10,000 charge/discharge cycles. The high capacitance and long cycle life were ascribed to the short diffusional paths, uniform PANI coating and tight confinement of the PANI in the inner pores of the tire-derived carbon via - interactions, which minimized the degradation of the PANI upon cycling. Here, we anticipate that the same strategy can be applied to deposit other pseudocapacitive materials with low-cost TC to achieve even higher electrochemical performance and longer cycle life, a key challenge for redox active polymers.

  19. Synchrotron Light Options at Super-B

    SciTech Connect (OSTI)

    Wittmer, Walter

    2012-04-27

    Super-B is a planned asymmetric high luminosity e{sup +}e{sup -} collider at the {Upsilon}(4S) resonance as PEP-II and KEKB, to be built in Italy. The Super-B High (HER, 7 GeV) and Low (LER, 4 GeV) Energy beams characteristics are comparable to NSLS-II and other state of the art synchrotron light sources. This suggests the use of this facility, either parasitically or in dedicated runs, as light source. In this paper we compare the characteristics of the synchrotron light generated at Super-B with existing, in construction and proposed facilities. We investigate different schemes to incorporate the generation of synchrotron radiation in the collider lattice design and look at different beam line layouts for users. In the past high energy particle colliders were designed to collide as many particle as possible. This was done by maximizing the beam current, using relative large emittances and squeezing the beam at the interaction point. During the operation of PEP II the limits of both raising the beam currents and squeezing the beam were experienced. Therefore the optics was modified to lower emittance. The successful test of the 'large Piwinski angle' and crab waist scheme, with extremely low design emittances, at the DAPHNE collider at Frascati made it the design choice for Super-B. Both HER and LER have been designed to meet these requirements and the design parameters relevant to our study, are shown in Table 1. As comparison the design parameters from NSLS II and other state of the art synchrotron light sources have been added to this table. From these parameters it is obvious that synchrotron radiation generated from both HER and LER is comparable to this last generation sources.

  20. Super Separator | Princeton Plasma Physics Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Super Separator February 12, 2013 Tweet Widget Google Plus One Share on Facebook Superior separation of nuclear waste: This advanced centrifuge under development at PPPL can deliver faster, more efficient and more economical separation of nuclear waste than standard centrifuges permit. The device, seen here in a PPPL-produced video, does not rotate as a rigid body, as standard centrifuges do. Instead, the inner cylinder rotates independently of the outer cylinder, creating a fluid flow known as

  1. Super-radiance and open quantum systems

    SciTech Connect (OSTI)

    Volya, Alexander [Department of Physics, Florida State University, Tallahassee, FL 32306-4350 (United States); Zelevinsky, Vladimir [NSCL, Michigan State University, East Lansing, MI 48824-1321 (United States); Department of Physics and Astronomy, Michigan State University, East Lansing, MI 48824-1321 (United States)

    2005-07-08

    Quantum wires, loosely bound nuclei, molecules in chemical reactions and exotic narrow pentaquark states are different examples of open quantum mesoscopic systems. The coupling with and through continuum is their common feature. We discuss general properties of quantum systems in the regime of strong continuum coupling, when the mechanism of Dicke super-radiance changes intrinsic dynamics, signatures of quantum chaos, lifetime of unstable states and reaction cross sections. The examples are shown for various areas of mesoscopic physics.

  2. Increasing Biofuel Deployment through Renewable Super Premium

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Demonstration & Market Transformation Platform Tim Theiss, ORNL Bob McCormick, NREL Jeongwoo Han, ANL Increasing Biofuel Deployment through Renewable Super Premium 2015 Bioenergy Technologies Office Peer Review March 23, 2015 2 | Bioenergy Technologies Office Project Goals are Aligned with DMT & BETO Goals 2025 CAFE Standards (U.S. EPA and U.S. NHTSA standards) FUEL ECONOMY STANDARDS 70% NO x & PM, 85% NMOG < 10 ppm sulfur in gasoline (U.S. EPA Tier 3 regulations) EMISSIONS

  3. Recent results from Super-Kamiokande

    SciTech Connect (OSTI)

    Himmel, Alexander; Collaboration: Super-Kamiokande Collaboration

    2014-06-24

    The Super-Kamiokande experiment has collected more than 11 live-years of atmospheric neutrino data. Atmospheric neutrinos cover a wide phase space in both energy and distance travelled, the parameters relevant for studying neutrino oscillations. We present here recent measurements of the three-flavor neutrino oscillation parameters using this atmospheric neutrino data, as well as new limits on mixing with a fourth sterile neutrino state.

  4. Vibration Budget for SuperB

    SciTech Connect (OSTI)

    Bertsche, K; Wittmer, W.; Bolzon, B.; Brunetti, L.; Jeremie, A.; Esposito, M.; Tomassini, S.; /Frascati

    2011-04-05

    We present a vibration budget for the SuperB accelerator. We include ground motion data, motion sensitivity of machine components, and beam feedback system requirements. The SuperB accelerator design attains at least 50 times higher than current B-factories due to smaller beam sizes and a crabbed waist crossing angle scheme at the IP (interaction point). The beam size (1{sigma}) at the IP will be about 10 {micro}m (horizontal) by 40 nm (vertical). These small beam sizes will make the luminosity very sensitive to mechanical vibration and electrical noise. Relative vertical misalignment of the two beams at the IP by only 8 nm will result in a 1% reduction in luminosity. The corresponding horizontal alignment tolerance of is 250x looser (2 {micro}m). The vertical beam angle at the IP for a 1% luminosity loss is fairly loose at 200 {micro}rad, and the horizontal beam angle tolerance is looser still. We will focus on vertical beam position at the IP, since this presents the greatest alignment challenge. The values presented here are for a closed orbit with tunes near a half-integer in the SuperB v.12 lattice.

  5. SECTION III: NUCLEAR THEORY

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Heavy quark three-body collisional energy loss in quark-gluon plasma...... III-1 C. M. Ko and Wei Liu Elliptic flow of deuterons in relativistic heavy ion ...

  6. SECTION III: NUCLEAR THEORY

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ...III-1 A.M. Mukhamedzhanov, V.Z. Goldberg, G. Rogachev, E. Johnson, S. Brown, K. Kemper, A. Momotyuk, and B. Roeder The Trojan Horse Method: an Indirect Technique...

  7. Part III The President

    Broader source: Energy.gov (indexed) [DOE]

    III The President Executive Order 13653-Preparing the United States for the Impacts of Climate Change VerDate Mar<15>2010 17:41 Nov 05, 2013 Jkt 226001 PO 00000 Frm 00001 Fmt 4717...

  8. Validation of the U.S. NRC coupled code system TRITON/TRACE/PARCS with the special power excursion reactor test III (SPERT III)

    SciTech Connect (OSTI)

    Wang, R. C.; Xu, Y.; Downar, T.; Hudson, N.

    2012-07-01

    The Special Power Excursion Reactor Test III (SPERT III) was a series of reactivity insertion experiments conducted in the 1950's. This paper describes the validation of the U.S. NRC Coupled Code system TRITON/PARCS/TRACE to simulate reactivity insertion accidents (RIA) by using several of the SPERT III tests. The work here used the SPERT III E-core configuration tests in which the RIA was initiated by ejecting a control rod. The resulting super-prompt reactivity excursion and negative reactivity feedback produced the familiar bell shaped power increase and decrease. The energy deposition during such a power peak has important safety consequences and provides validation basis for core coupled multi-physics codes. The transients of five separate tests are used to benchmark the PARCS/TRACE coupled code. The models were thoroughly validated using the original experiment documentation. (authors)

  9. Worker exposure to chemical agents in the manufacture of rubber tires and tubes: particulates

    SciTech Connect (OSTI)

    Williams, T.M.; Harris, R.L.; Arp, E.W.; Symons, M.J.; Van Ert, M.D.

    1980-03-01

    The Occupational Health Studies Group industrial hygiene studies at a group of 14 tire and tube manufacturing plants chosen to represent a cross-section of the industry include numerous evaluations of potential exposure to airborne particulate matter. Results of these environmental particulate sampling studies are reported by plant and by occupational groups within plants. High volume, open face and cyclone samplers were employed to evaluate both personnel and area particulate concentrations. The concentrations of particulates yielded by high volume and open face total particulate samplers are compared with those of comparison samples of respirable material. Personnel samples of particulates are compared with general air samples taken in the same work area. An overall review and comparison is given of particulate exposures to workers in various occupational title groups where particulate materials are released to the air from processes or operations.

  10. Feasibility study for thermal treatment of solid tire wastes in Bangladesh by using pyrolysis technology

    SciTech Connect (OSTI)

    Islam, M.R.; Joardder, M.U.H.; Hasan, S.M.; Takai, K.; Haniu, H.

    2011-09-15

    In this study on the basis of lab data and available resources in Bangladesh, feasibility study has been carried out for pyrolysis process converting solid tire wastes into pyrolysis oils, solid char and gases. The process considered for detailed analysis was fixed-bed fire-tube heating pyrolysis reactor system. The comparative techno-economic assessment was carried out in US$ for three different sizes plants: medium commercial scale (144 tons/day), small commercial scale (36 tons/day), pilot scale (3.6 tons/day). The assessment showed that medium commercial scale plant was economically feasible, with the lowest unit production cost than small commercial and pilot scale plants for the production of crude pyrolysis oil that could be used as boiler fuel oil and for the production of upgraded liquid-products.

  11. Base Technology and Tools for Super Critical Reservoir | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Base Technology and Tools for Super Critical Reservoir Base Technology and Tools for Super Critical Reservoir Project objective: Develop building blocks necessary for robust tools that can operate in supercritical environments. high_henfling_super_critical_reservoir.pdf (305.92 KB) More Documents & Publications track 3: enhanced geothermal systems (EGS) | geothermal 2015 peer review Development of a HT Seismic Tool Harsh Environment Silicon Carbide Sensor Technology for Geothermal

  12. Vehicle Technologies Office Merit Review 2015: Volvo SuperTruck -

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Powertrain Technologies for Efficiency Improvement | Department of Energy SuperTruck - Powertrain Technologies for Efficiency Improvement Vehicle Technologies Office Merit Review 2015: Volvo SuperTruck - Powertrain Technologies for Efficiency Improvement Presentation given by Volvo at 2015 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about Volvo SuperTruck - powertrain technologies for efficiency improvement.

  13. Convection feedbacks in a super-parameterization GCM

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Convection feedbacks in a super-parameterization GCM Luo, Zhengzhao (Johnny) Colorado State University Stephens, Graeme Colorado State University Category: Modeling Both the Colorado State University (CSU) and Goddard super-parameterization GCM (SP-GCM) simulate a super-active Asian summer monsoon with unrealistically enhanced levels of precipitation. The underlying physical mechanism for this monsoon bias in the CSU SP-GCM is shown to involve enhanced convection-wind-evaporation feedbacks. The

  14. Super Wind Project Pvt Ltd | Open Energy Information

    Open Energy Info (EERE)

    Project Pvt Ltd Jump to: navigation, search Name: Super Wind Project Pvt. Ltd. Place: Pune, Maharashtra, India Zip: 411001 Sector: Wind energy Product: Pune-based wind project...

  15. Task Order Price Evaluation Worksheet for SUPER ESPC

    Broader source: Energy.gov [DOE]

    Document provides a worksheet for evaluating price for a task order as part of a Super Energy Savings Performance Contract (ESPC).

  16. Super Bowl of Energy: Solar Smashes Records | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Super Bowl of Energy: Solar Smashes Records Super Bowl of Energy: Solar Smashes Records February 3, 2014 - 5:45pm Addthis MetLife Stadium, the site of yesterday's Super Bowl, features a ring of 1,350 solar panels that can generate 350,000 kilowatt hours of electricity annually. The number of jobs in the U.S. solar energy industry equates to nearly double the amount of seats in the stadium. Picture courtesy NRG Solar, LLC MetLife Stadium, the site of yesterday's Super Bowl, features a ring of

  17. Cummins SuperTruck Program - Technology and System Level Demonstration...

    Broader source: Energy.gov (indexed) [DOE]

    More Documents & Publications Cummins SuperTruck Program - Technology and System Level Demonstration of Highly Efficient and Clean, Diesel Powered Class 8 Trucks Supertruck ...

  18. SuperTruck Team Achieves 115% Freight Efficiency Improvement...

    Broader source: Energy.gov (indexed) [DOE]

    While the original SuperTruck goal was to improve freight efficiency by 50 percent compared to a baseline vehicle, Daimler Trucks North America (DTNA) announced that their ...

  19. A young person's view of the Superconducting Super Collider

    SciTech Connect (OSTI)

    Moya, A.

    1990-08-01

    This report gives a simple description of the Superconducting Super Collider, how it works, and what it is used for. (LSP)

  20. Application of Super-Hydrophobic Coating for Enhanced Water Repellency...

    Office of Scientific and Technical Information (OSTI)

    for Enhanced Water Repellency of Ballistic Fabric Citation Details In-Document Search Title: Application of Super-Hydrophobic Coating for Enhanced Water Repellency of ...

  1. Second Generation Super Boiler Technology for Watertube Boilers

    SciTech Connect (OSTI)

    2007-07-01

    This factsheet describes a research project to develop a high-pressure watertube boiler system that incorporates and improves upon the capabilities of the firetube Super Boiler system.

  2. Vehicle Technologies Office Merit Review 2014: Cummins SuperTruck...

    Energy Savers [EERE]

    Cummins SuperTruck Program Technology and System Level Demonstration of Highly Efficient ... Program Technology and System Level Demonstration of Highly Efficient and Clean, Diesel ...

  3. Vehicle Technologies Office Merit Review 2015: Volvo SuperTruck |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy SuperTruck Vehicle Technologies Office Merit Review 2015: Volvo SuperTruck Presentation given by Volvo Trucks at 2015 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about Volvo SuperTruck. vss081_amar_2015_o.pdf (2.12 MB) More Documents & Publications SuperTruck … Development and Demonstration of a Fuel-Efficient Class 8 Tractor & Trailer Vehicle Technologies Office Merit Review 2015: Volvo

  4. III-V-N materials for super high-efficiency multijunction solar cells

    SciTech Connect (OSTI)

    Yamaguchi, Masafumi; Bouzazi, Boussairi; Suzuki, Hidetoshi; Ikeda, Kazuma; Kojima, Nobuaki; Ohshita, Yoshio

    2012-10-06

    We have been studying concentrator multi-junction solar cells under Japanese Innovative Photovoltaic R and D program since FY2008. InGaAsN is one of appropriate materials for 4-or 5-junction solar cell configuration because this material can be lattice-matched to GaAs and Ge substrates. However, present InGaAsN single-junction solar cells have been inefficient because of low minority-carrier lifetime due to N-related recombination centers and low carrier mobility due to alloy scattering and non-homogeneity of N. This paper presents our major results in the understanding of majority and minority carrier traps in GaAsN grown by chemical beam epitaxy and their relationships with the poor electrical properties of the materials.

  5. Fusion Power Demonstration III

    SciTech Connect (OSTI)

    Lee, J.D.

    1985-07-01

    This is the third in the series of reports covering the Fusion Power Demonstration (FPD) design study. This volume considers the FPD-III configuration that incorporates an octopole end plug. As compared with the quadrupole end-plugged designs of FPD-I and FPD-II, this octopole configuration reduces the number of end cell magnets and shortens the minimum ignition length of the central cell. The end-cell plasma length is also reduced, which in turn reduces the size and cost of the end cell magnets and shielding. As a contiuation in the series of documents covering the FPD, this report does not stand alone as a design description of FPD-III. Design details of FPD-III subsystems that do not differ significantly from those of the FPD-II configuration are not duplicated in this report.

  6. The Super-B Project Accelerator Status

    SciTech Connect (OSTI)

    Biagini, M.E.; Alesini, D.; Boni, R.; Boscolo, M.; Demma, T.; Drago, A.; Esposito, M.; Guiducci, S.; Marcellini, F.; Mazzitelli, G.; Preger, M.; Raimondi, P.; Sanelli, C.; Serio, M.; Stecchi, A.; Stella, A.; Tomassini, S.; Zobov, M.; Bertsche, K.; Brachmann, A.; Cai, Y.; /SLAC /Novosibirsk, IYF /Annecy, LAPP /LPSC, Grenoble /Orsay, LAL /Saclay /Pisa U. /CERN

    2011-08-17

    The SuperB project is an international effort aiming at building in Italy a very high luminosity e{sup +}e{sup -} (10{sup 36} cm{sup -2} sec{sup -1}) asymmetric collider at the Y(4S) energy in the CM. The accelerator design has been extensively studied and changed during the past year. The present design, based on the new collision scheme, with large Piwinski angle and the use of 'crab waist' sextupoles already successfully tested at the DA{Phi}NE {Phi}-Factory at LNF Frascati, provides larger flexibility, better dynamic aperture and spin manipulation sections in the Low Energy Ring (LER) for longitudinal polarization of the electron beam at the Interaction Point (IP). The Interaction Region (IR) has been further optimized in terms of apertures and reduced backgrounds in the detector. The injector complex design has been also updated. A summary of the project status will be presented in this paper. The SuperB collider can reach a peak luminosity of 10{sup 36} cm{sup -2} sec{sup -1} with beam currents and bunch lengths similar to those of the past and present e{sup +}e{sup -} Factories, through the use of smaller emittances and new scheme of crossing angle collision. The beams are stored in two rings at 6.7 GeV (HER) and 4.2 GeV (LER). Unique features of the project are the polarization of the electron beam in the LER and the possibility to decrease the energies for running at the {tau}/charm threshold. The option to reuse the PEP-II B-Factory (SLAC) hardware will allow reducing costs. The SuperB facility will require a big complex of civil infrastructure. The main construction, which will house the final part of the LINAC, the injection lines, the damping rings, and the storage rings, will be mainly underground. Two sites have been considered: the campus of Tor Vergata University near Frascati, and the INFN Frascati Laboratory. No decision has been made yet. A footprint of the possible SuperB layout on the LNF area is shown in Fig. 1.

  7. From super beams to neutrino factories

    SciTech Connect (OSTI)

    Bross, Alan; /Fermilab

    2009-11-01

    The Neutrino Factory, which produces an extremely intense source of flavor-tagged neutrinos from muon decays in a storage ring, arguably gives the best physics reach for CP violation, as well as virtually all parameters in the neutrino oscillation parameter space. I will briefly describe the physics capabilities of the baseline Neutrino Factory as compared to other possible future facilities ({beta}-beam and super-beam facilities), give an overview of the accelerator complex and describe in detail the current international R&D program.

  8. Production of super-smooth articles

    DOE Patents [OSTI]

    Duchane, David V.

    1983-01-01

    Super-smooth rounded or formed articles made of thermoplastic materials including various poly(methyl methacrylate) or acrylonitrile-butadiene-styrene copolymers are produced by immersing the articles into a bath, the composition of which is slowly changed with time. The starting composition of the bath is made up of at least one solvent for the polymer and a diluent made up of at least one nonsolvent for the polymer and optional materials which are soluble in the bath. The resulting extremely smooth articles are useful as mandrels for laser fusion and should be useful for a wide variety of other purposes, for example lenses.

  9. NEMO 3 And SuperNEMO

    SciTech Connect (OSTI)

    Sutton, C. Sean [Mount Holyoke College, South Hadley, Massachusetts 01075 (United States)

    2006-11-17

    The NEMO 3 double beta decay detector has been running since February 2003. The first runs identified an unexpected abundance of radon within the detector. The successful solution to this problem is presented here. No evidence of neutrinoless double beta decay has been observed. The current limits are T{sub (1/2)}{sup 0{nu}} ({sup 100}Mo) > 5.8 x 10{sup 23}y and T{sub (1/2)}{sup 0{nu}} ({sup 82}Se) > 2.1 x 10{sup 23}y. The anticipated limits on neutrinoless double beta decay in five years for NEMO 3 are also presented. The design criterion for the next generation detector, SuperNEMO, are spelled out with restrictions on its resolution and radiopurity. The intended sensitivity for SuperNEMO, is to reach 1 to 2 x 1026y or an effective neutrino mass of 50 meV in 10 years, so as to probe the inverted neutrino mass hierarchy.

  10. EIS-0138-S: Superconducting Super Collider, Supplemental, Waxahatchie, Texas

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy developed this supplementary statement to analyze the environmental impacts of design modifications to the Superconducting Super Collider that were made following the publication of the Record of Decision that selected Ellis County, Texas, as the location of the laboratory facility. This statement supplements DOE/EIS-0138, Superconducting Super Collider.

  11. TEM study of PM2.5 emitted from coal and tire combustion in a thermal power station

    SciTech Connect (OSTI)

    Reto Giere; Mark Blackford; Katherine Smith

    2006-10-15

    The research presented here was conducted within the scope of an experiment investigating technical feasibility and environmental impacts of tire combustion in a coal-fired power station. Previous work has shown that combustion of a coal + tire blend rather than pure coal increased bulk emissions of various elements (e.g., Zn, As, Sb, Pb). The aim of this study is to characterize the chemical and structural properties of emitted single particles with dimensions <2.5 {mu}m (PM2.5). This transmission electron microscope (TEM)-based study revealed that, in addition to phases typical of coal fly ash (e.g., aluminum-silicate glass, mullite), the emitted PM2.5 contains amorphous selenium particles and three types of crystalline metal sulfates never reported before from stack emissions. Anglesite, PbSO{sub 4}, is ubiquitous in the PM2.5 derived from both fuels and contains nearly all Pb present in the PM. Gunningite, ZnSO{sub 4}H{sub 2}O, is the main host for Zn and only occurs in the PM derived from the coal + tire blend, whereas yavapaiite, KFe{sup 3+}(SO{sub 4}){sub 2}, is present only when pure coal was combusted. It is concluded that these metal sulfates precipitated from the flue gas may be globally abundant aerosols and have, through hydration or dissolution, a major environmental and health impact. 66 refs., 2 figs., 1 tab.

  12. Recycling of rubber tires in electric arc furnace steelmaking: simultaneous combustion of metallurgical coke and rubber tyres blends

    SciTech Connect (OSTI)

    Magdalena Zaharia; Veena Sahajwalla; Byong-Chul Kim; Rita Khanna; N. Saha-Chaudhury; Paul O'Kane; Jonathan Dicker; Catherine Skidmore; David Knights

    2009-05-15

    The present study investigates the effect of addition of waste rubber tires on the combustion behavior of its blends with coke for carbon injection in electric arc furnace steelmaking. Waste rubber tires were mixed in different proportions with metallurgical coke (MC) (10:90, 20:80, 30:70) for combustion and pyrolysis at 1473 K in a drop tube furnace (DTF) and thermogravimetric analyzer (TGA), respectively. Under experimental conditions most of the rubber blends indicated higher combustion efficiencies compared to those of the constituent coke. In the early stage of combustion the weight loss rate of the blends is much faster compared to that of the raw coke due to the higher volatile yield of rubber. The presence of rubber in the blends may have had an impact upon the structure during the release and combustion of their high volatile matter (VM) and hence increased char burnout. Measurements of micropore surface area and bulk density of the chars collected after combustion support the higher combustion efficiency of the blends in comparison to coke alone. The surface morphology of the 30% rubber blend revealed pores in the residual char that might be attributed to volatile evolution during high temperature reaction in oxygen atmosphere. Physical properties and VM appear to have a major effect upon the measured combustion efficiency of rubber blends. The study demonstrates that waste rubber tires can be successfully co-injected with metallurgical coke in electric arc furnace steelmaking process to provide additional energy from combustion. 44 refs., 11 figs., 2 tabs.

  13. SuperTruck … Development and Demonstration of a Fuel-Efficient...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications SuperTruck Development and Demonstration of a Fuel-Efficient Class 8 Tractor & Trailer SuperTruck Development and Demonstration of a ...

  14. Crystal Structure of a Super Leucine Zipper an Extended Two-Stranded Super Long Coiled Coil

    SciTech Connect (OSTI)

    J Diao

    2011-12-31

    Coiled coil is a ubiquitous structural motif in proteins, with two to seven alpha helices coiled together like the strands of a rope, and coiled coil folding and assembly is not completely understood. A GCN4 leucine zipper mutant with four mutations of K3A, D7A, Y17W, and H18N has been designed, and the crystal structure has been determined at 1.6 {angstrom} resolution. The peptide monomer shows a helix trunk with short curved N- and C-termini. In the crystal, two monomers cross in 35{sup o} and form an X-shaped dimer, and each X-shaped dimer is welded into the next one through sticky hydrophobic ends, thus forming an extended two-stranded, parallel, super long coiled coil rather than a discrete, two-helix coiled coil of the wild-type GCN4 leucine zipper. Leucine residues appear at every seventh position in the super long coiled coil, suggesting that it is an extended super leucine zipper. Compared to the wild-type leucine zipper, the N-terminus of the mutant has a dramatic conformational change and the C-terminus has one more residue Glu 32 determined. The mutant X-shaped dimer has a large crossing angle of 35{sup o} instead of 18{sup o} in the wild-type dimer. The results show a novel assembly mode and oligomeric state of coiled coil, and demonstrate that mutations may affect folding and assembly of the overall coiled coil. Analysis of the formation mechanism of the super long coiled coil may help understand and design self-assembling protein fibers.

  15. George F. Smoot III

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    George F. Smoot III About the Lab Our Vision Lab Leadership History Nobelists Visit ⇒ Navigate Section About the Lab Our Vision Lab Leadership History Nobelists Visit smoot 2006 Nobel Prize for Physics * October 3, 2006 Press Conference (Video) * Bibliography of Dr. Smoot's Works * October 3, 2006 Press Conference (Video) The October 3, 2006 press conference at Berkeley Lab introducing its newest Nobel Prize winner, George Smoot, to a throng of visiting media is available for viewing online.

  16. III-Nitride Nanowires

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    III-Nitride Nanowires - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Energy Defense Waste Management Programs Advanced

  17. Iii;.} An Ann

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Iii;.} An Ann otated Bibli ography of the Red - Coc kaded Woodpecker bv * Jerom e A. Jack son A Publi cati on of the Sava nnah River Plonl Notional En... ironmentol Research Pork PrOQ rom United Stales Dep ortment of Ene r gy An Annotated Bibliography of the Red-Cockaded Woodpecker, Picoides borealis Jerome A. Jackson Department of Biological Sciences Mississippi State University Mississippi State, Mississippi A Publication of the Savannah River National Environmental Research Park Prepared

  18. Part III - Section J

    National Nuclear Security Administration (NNSA)

    Corporation Contract No. DE-AC04-94AL85000 Modification No. 585 Attachment 2 Page 1 of 5 Part III - Section J Appendix G List of Applicable Directives and NNSA Policy Letters In addition to the list of applicable directives referenced below, the contractor shall also comply with supplementary directives (e.g., manuals), which are invoked by a Contractor Requirements Document (CRD) attached to a directive referenced below. This List excludes directives that have been granted an exemption from the

  19. Part III - Section J

    National Nuclear Security Administration (NNSA)

    M280 Attachment 1 Page 1 of 5 Part III - Section J Appendix G List of Applicable Directives and NNSA Policy Letters In addition to the list of applicable directives referenced below, the contractor shall also comply with supplementary directives (e.g., manuals), which are invoked by a Contractor Requirements Document (CRD) attached to a directive referenced below. DIRECTIVE NUMBER DATE DOE DIRECTIVE TITLE APPH Chapter X Revision 10 09/08/98 Accounting Practices & Procedures Handbook Chapter

  20. THE BNL SUPER NEUTRINO BEAM PROJECT.

    SciTech Connect (OSTI)

    RAPARIA,D.

    2005-01-26

    BNL plans to create a very long base line super neutrino beam facility by upgrading the AGS from the current 0.14 MW to 1.0 MW and beyond. The proposed facility consists of three major components. First is a 1.5 GeV superconducting linac to replace the booster as injector for the AGS, second is the performance upgrade of the AGS itself for higher intensity and repetition rate, and finally is the target and horn system for the neutrino production. The major contribution for the higher power is from the increase of the repetition rate of the AGS from 0.3 Hz to 2.5 Hz, with moderate increase from the intensity. The accelerator design considerations to achieve high intensity and low losses for the new linac and the AGS will be presented. The target and horn design for high power operation and easy maintenance will also be covered.

  1. Carbon Film Electrodes For Super Capacitor Applications

    DOE Patents [OSTI]

    Tan, Ming X.

    1999-07-20

    A method for treating an organic polymer material, preferably a vinylidene chloride/vinyl chloride copolymer (Saran) to produce a flat sheet of carbon film material having a high surface area (.apprxeq.1000 m.sup.2 /g) suitable as an electrode material for super capacitor applications. The method comprises heating a vinylidene chloride/vinyl chloride copolymer film disposed between two spaced apart graphite or ceramic plates to a first temperature of about 160.degree. C. for about 14 hours to form a stabilized vinylidene chloride/vinyl chloride polymer film, thereafter heating the stabilized film to a second temperature of about 750.degree. C. in an inert atmosphere for about one hour to form a carbon film; and finally activating the carbon film to increase the surface area by heating the carbon film in an oxidizing atmosphere to a temperature of at least 750-850.degree. C. for between 1-6 hours.

  2. Plutonium (III) and uranium (III) nitrile complexes

    SciTech Connect (OSTI)

    Enriquez, A. E.; Matonic, J. H.; Scott, B. L.; Neu, M. P.

    2002-01-01

    Iodine oxidation of uranium and plutonium metals in tetrahydrofuran and pyridine form AnI{sub 3}(THF){sub 4} and AnI{sub 3}(py){sub 4} (An = Pu, U). These compounds represent convenient entries Into solution An(III) chemistry in organic solvents. Extensions of the actinide metal oxidation methodology in nitrile solvents by I{sub 2}, AgPF{sub 6}, and TIPF{sub 6} are presented here. Treatment of Pu{sup 0} in acetonitrile with iodine yields a putative PuI{sub 3}(NCMe){sub x} intermediate which can be trapped with the tripodal nitrogen donor ligand tpza (tpza = (tris[(2-pyrazinyl)methyl]amine)) and forms the eight-coordinate complex (tpza)PuI{sub 3}(NCMe). Treatment of excess U{sup 0} metal by iodine in acetonitrile afforded a brown crystalline mixed valence complex, [U(NCMe){sub 9}][UI{sub 6}][I], instead of UI{sub 3}(NCMe){sub 4}. The analogous reaction in bezonitrile forms red crystalline UI{sub 4}(NCPh){sub 4}. In contrast, treatment of UI{sub 3}(THF){sub 4} with excess acetonitrile cleanly generates [U(NCMe){sub 9}][I]{sub 3}. Oxidation of Pu{sup 0} by either TI(I) or Ag(I) hexafluorophosphate salts generates a nine-coordinate homoleptic acetonitrile adduct [Pu(NCMe){sub 9}][PF{sub 6}]{sub 3}. Attempts to oxidize U{sub 0} with these salts were unsuccessful.

  3. Windy Flats Phase III | Open Energy Information

    Open Energy Info (EERE)

    Phase III Jump to: navigation, search Name Windy Flats Phase III Facility Windy Flats Phase III Sector Wind energy Facility Type Commercial Scale Wind Facility Status Proposed...

  4. Superfund Record of Decision (EPA Region 3): Rhinehart Tire Fire Dump, Operable Unit 2, Winchester, VA. (Second remedial action), September 1992

    SciTech Connect (OSTI)

    Not Available

    1992-09-29

    The Rhinehart Tire Fire Dump site is located in a 22-acre drainage area of a sparsely populated rural area in western Frederick County, Virginia. Surface water runoff flows into a north-south tributary that discharges to Hogue Creek, which is 4,000 feet downstream. Bedrock is noted to be highly fractured, and the ground water flow in the overburden aquifer is toward Massey Run. From 1972 to 1983, the site owner conducted a tire disposal operation, which consisted of transporting discarded tires from various locations and storing them on a 5-acre wooded slope behind his home. An estimated 5 to 7 million tires that had been accumulated caught on fire in October 1983 and burned until July 1984. As a result of the fire, a free-flowing oily-tar, which contained anthracene, benzene, cadmium, chromium, ethylbenzene, napthalene, nickel, pyrene, toluene, and zinc, began to seep out of the tire pile into Massey Run and on to Hogue Creek.

  5. INFOGRAPHIC: How SuperTruck is Making Heavy Duty Vehicles More Efficient

    Broader source: Energy.gov [DOE]

    How the Energy Department's SuperTruck initiative is making America's heavy duty trucks more sustainable.

  6. Development of the conventional facilities of the Superconducting Super Collider. Revision 1

    SciTech Connect (OSTI)

    Toohig, T.E.

    1994-02-01

    This report discusses an overview of the construction of facilities at the Superconducting Super Collider.

  7. SPIDERS Phase III

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SPIDERS Phase III John Bothof Burns & McDonnell Definition The U.S. Department of Energy's official definition of a microgrid is "a group of interconnected loads and distributed energy resources within clearly defined electrical boundaries that acts as a single controllable entity with respect to the grid [and can] connect and disconnect from the grid to enable it to operate in both grid-connected or island-mode." Definition The U.S. Department of Energy's official definition of a

  8. Mr. Andrew Wallo, III

    Office of Legacy Management (LM)

    ,- -.-=* Stub 4000. ,955 L' EnJan: Plaza. 5. W.. Wahington. D. C. 20021. T&phone: (20.2) 188.6000 7117-03.87.cdy.02 13 January 1987 Mr. Andrew Wallo, III Division of Facility & Site Decommissioning Projects U.S. Department of E,nergy Germantown, Maryland 20545 Dear Mr. Wallo: CONTACT REPORT - DISCUSSIONS WITH MR. WILLIAM A. HOOPER MANAGER, PLANT ENGINEERING, ALLIED BENDIX AEROSPACE SECTOR TETERBORO, NEW JERSEY Per your request, the undersigned contacted Mr. William A. Hooper on 8 January

  9. SECTION III. NUCLEAR THEORY

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    III. NUCLEAR THEORY Microscopic Description of Excitation of Isoscalar Giant Dipole Resonance in 28Si and 208Pb A. Kolomiets, O. Pochivalov and S. Shlomo Microscopic Description of Excitation of Isoscalar Giant Quadrupole Resonances in 28Si, 40Ca, 58Ni, and 116Sn by Inelastic Scattering of 240 MeV α-particles A. Kolomiets, O. Pochivalov and S. Shlomo Microscopic Description of Excitation of Isoscalar Giant Monopole Resonance in 58Ni by Inelastic Scattering of 240 MeV α-particles A. Kolomiets,

  10. Super Hydro Electric Pvt Ltd | Open Energy Information

    Open Energy Info (EERE)

    Electric Pvt Ltd Jump to: navigation, search Name: Super Hydro Electric Pvt. Ltd. Place: New Delhi, Delhi (NCT), India Zip: 1100024 Sector: Hydro Product: Delhi-based small hydro...

  11. EERE Success Story-SuperTruck Initiative Partner Improves Class...

    Office of Environmental Management (EM)

    ... INFOGRAPHIC: How SuperTruck is Making Heavy Duty Vehicles More Efficient As part of the 21st Century Truck Partnership, the Army will demonstrate technology that converts waste ...

  12. Green Supers Graduate Prepared to Make NYC More Energy Efficient

    Broader source: Energy.gov [DOE]

    Secretary Chu delivered the graduation address for the Green Supers program in New York City. The 40-hour program teaches building superintendents everything they need to know about green building operations and maintenance.

  13. Super Bowl of Energy: Solar Smashes Records | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Addthis MetLife Stadium, the site of yesterday's Super Bowl, features a ring of 1,350 solar panels that can generate 350,000 kilowatt hours of electricity annually. The number of ...

  14. Northwest students battle wits at Super Bowl of Science?

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    BPA, 503-230-7536 or Mike Hansen, BPA, 503-230-4328 media line 503-230-5131 Northwest students battle wits at "Super Bowl of Science" BPA sponsors the 21 st annual Regional Science...

  15. A braided monoidal category for free super-bosons

    SciTech Connect (OSTI)

    Runkel, Ingo

    2014-04-15

    The chiral conformal field theory of free super-bosons is generated by weight one currents whose mode algebra is the affinisation of an abelian Lie super-algebra h with non-degenerate super-symmetric pairing. The mode algebras of a single free boson and of a single pair of symplectic fermions arise for even|odd dimension 1|0 and 0|2 of h, respectively. In this paper, the representations of the untwisted mode algebra of free super-bosons are equipped with a tensor product, a braiding, and an associator. In the symplectic fermion case, i.e., if h is purely odd, the braided monoidal structure is extended to representations of the Z/2Z-twisted mode algebra. The tensor product is obtained by computing spaces of vertex operators. The braiding and associator are determined by explicit calculations from three- and four-point conformal blocks.

  16. POPULATION III HYPERNOVAE

    SciTech Connect (OSTI)

    Smidt, Joseph; Whalen, Daniel J.; Wiggins, Brandon K.; Even, Wesley; Fryer, Chris L.; Johnson, Jarrett L.

    2014-12-20

    Population III supernovae have been of growing interest of late for their potential to directly probe the properties of the first stars, particularly the most energetic events that are visible near the edge of the observable universe. Until now, hypernovae, the unusually energetic Type Ib/c supernovae that are sometimes associated with gamma-ray bursts, have been overlooked as cosmic beacons at the highest redshifts. In this, the latest of a series of studies on Population III supernovae, we present numerical simulations of 25-50 M {sub ☉} hypernovae and their light curves done with the Los Alamos RAGE and SPECTRUM codes. We find that they will be visible at z = 10-15 to the James Webb Space Telescope and z = 4-5 to the Wide-Field Infrared Survey Telescope, tracing star formation rates in the first galaxies and at the end of cosmological reionization. If, however, the hypernova crashes into a dense shell ejected by its progenitor, it is expected that a superluminous event will occur that may be seen at z ∼ 20 in the first generation of stars.

  17. Health assessment for Rhinehart (Aka Winchester) Tire Fire National Priorities List (NPL) Site, Frederick County, Virginia, Region 3. CERCLIS No. VAD980831796. Final report

    SciTech Connect (OSTI)

    Not Available

    1989-04-17

    The Rhinehart (aka Winchester) Tire Fire Site is located near the town of Winchester in Frederick County, Virginia. In October 1983, a fire was started in the tires disposed of on the site. Hot oil was released from the melting and pyrolysis of the tires. This oil made its way to Massey Run, a nearby surface water body. The fire was brought under control within a few days, but continued to smolder for six months. The migration of the oil and the residue from the fire have contaminated the site. The site is of potential public health concern because of the risk to human health resulting from possible exposure to hazardous substances at concentrations that may result in adverse human health effects. Human exposure to heavy metals, polynuclear aromatic hydrocarbons and volatile organic compounds may occur via ingestion, inhalation and dermal absorption of contaminated groundwater, surface water, sediments and soils.

  18. Super Cool Appliance Design Wins Student Competition | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Super Cool Appliance Design Wins Student Competition Super Cool Appliance Design Wins Student Competition August 23, 2012 - 2:44pm Addthis The winners of the Max Tech and Beyond competition -- a team of University of Maryland students -- designed and built a prototype for a wall unit air conditioner that showed more than 30 percent energy savings when tested in a lab. | Photo courtesy of Yunho Hwang, University of Maryland. The winners of the Max Tech and Beyond competition -- a team of

  19. Regulatory and Commercial Barriers to Introduction of Renewable Super

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Premium | Department of Energy Regulatory and Commercial Barriers to Introduction of Renewable Super Premium Regulatory and Commercial Barriers to Introduction of Renewable Super Premium Breakout Session 2: Frontiers and Horizons Session 2-B: End Use and Fuel Certification Robert McCormick, Principal Engineer in Fuels Performance, National Renewable Energy Laboratory b13_mccormick_2-b.pdf (974.85 KB) More Documents & Publications The Impact of Low Octane Hydrocarbon Blending Streams on

  20. Super Truck Program: Engine Project Review | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    of Energy Presents first year highlights from Detroit Diesel Corporation and Daimler Trucks, NA joint SuperTruck engine and vehicle project to demonstrate a 50 percent freight efficiency improvement deer11_sisken.pdf (2.17 MB) More Documents & Publications Super Truck Program: Engine Project Review High-Efficiency Engine Technologies Session Introduction Roadmapping Engine Technology for Post-2020 Heavy Duty Vehicles

    1 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies

  1. Optical data transmission at the superconducting super collider

    SciTech Connect (OSTI)

    Leskovar, B.

    1989-04-01

    Digital and analog data transmissions via fiber optics for the Superconducting Super Collider have been investigated. The state of the art of optical transmitters, low loss fiber waveguides, receivers and associated electronics components are reviewed and summarized. Emphasis is placed on the effects of the radiation environment on the performance of an optical data transmission system components. Also, the performance of candidate components of the wide band digital and analog transmission systems intended for deployment in the Superconducting Super Collider Detector is discussed.

  2. THE ALBEDOS OF KEPLER'S CLOSE-IN SUPER-EARTHS

    SciTech Connect (OSTI)

    Demory, Brice-Olivier

    2014-07-01

    Exoplanet research focusing on the characterization of super-Earths is currently limited to the handful of targets orbiting bright stars that are amenable to detailed study. This Letter proposes to look at alternative avenues to probe the surface and atmospheric properties of this category of planets, known to be ubiquitous in our galaxy. I conduct Markov Chain Monte Carlo light-curves analyses for 97 Kepler close-in R{sub P} ? 2.0 R {sub ?} super-Earth candidates with the aim of detecting their occultations at visible wavelengths. Brightness temperatures and geometric albedos in the Kepler bandpass are constrained for 27 super-Earth candidates. A hierarchical Bayesian modeling approach is then employed to characterize the population-level reflective properties of these close-in super-Earths. I find median geometric albedos A{sub g} in the Kepler bandpass ranging between 0.16 and 0.30, once decontaminated from thermal emission. These super-Earth geometric albedos are statistically larger than for hot Jupiters, which have medians A{sub g} ranging between 0.06 and 0.11. A subset of objects, including Kepler-10b, exhibit significantly larger albedos (A{sub g} ? 0.4). I argue that a better understanding of the incidence of stellar irradation on planetary surface and atmospheric processes is key to explain the diversity in albedos observed for close-in super-Earths.

  3. Super-resolution with a positive epsilon multi-quantum-well super-lens

    SciTech Connect (OSTI)

    Bak, A. O.; Giannini, V.; Maier, S. A.; Phillips, C. C.

    2013-12-23

    We design an anisotropic and dichroic quantum metamaterial that is able to achieve super-resolution without the need for a negative permittivity. When exploring the parameters of the structure, we take into account the limits of semiconductor fabrication technology based on quantum well stacks. By heavily doping the structure with free electrons, we infer an anisotropic effective medium with a prolate ellipsoid dispersion curve which allows for near-diffractionless propagation of light (similar to an epsilon-near-zero hyperbolic lens). This, coupled with low absorption, allows us to resolve images at the sub-wavelength scale at distances 6?times greater than equivalent natural materials.

  4. THE BNL SUPER NEUTRINO BEAM PROJECT

    SciTech Connect (OSTI)

    WENG,W-T.; RAPARIA,D.

    2004-12-02

    To determine the neutrino mixing amplitudes and phase accurately, as well as the CP violation parameters, a very long base line super neutrino beam facility is needed. This is possible due to the long distance and wideband nature of the neutrino beam for the observation of several oscillations from one species of the neutrino to the other [1,2]. BNL plans to upgrade the AGS proton beam from the current 0.14 MW to higher than 1.0 MW and beyond for such a neutrino facility which consists of three major subsystems. First is a 1.5 GeV superconducting linac to replace the booster as injector for the AGS, second is the performance upgrade for the AGS itself for the higher intensity and repetition rate, and finally is target and horn system for the neutrino production. The major contribution for the higher power is from the increase of the repetition rate of the AGS form 0.3 Hz to 2.5 Hz, with moderate increase from the intensity [3]. The design consideration to achieve high intensity and low losses for the linac and the AGS will be reviewed. The target horn design for high power operation and easy maintenance will also be presented.

  5. SuperB Progress Report for Accelerator

    SciTech Connect (OSTI)

    Biagini, M.E.; Boni, R.; Boscolo, M.; Buonomo, B.; Demma, T.; Drago, A.; Esposito, M.; Guiducci, S.; Mazzitelli, G.; Pellegrino, L.; Preger, M.A.; Raimondi, P.; Ricci, R.; Rotundo, U.; Sanelli, C.; Serio, M.; Stella, A.; Tomassini, S.; Zobov, M.; Bertsche, K.; Brachman, A.; /SLAC /Novosibirsk, IYF /INFN, Pisa /Pisa U. /Orsay, LAL /Annecy, LAPP /LPSC, Grenoble /IRFU, SPP, Saclay /DESY /Cockroft Inst. Accel. Sci. Tech. /U. Liverpool /CERN

    2012-02-14

    This report details the progress made in by the SuperB Project in the area of the Collider since the publication of the SuperB Conceptual Design Report in 2007 and the Proceedings of SuperB Workshop VI in Valencia in 2008. With this document we propose a new electron positron colliding beam accelerator to be built in Italy to study flavor physics in the B-meson system at an energy of 10 GeV in the center-of-mass. This facility is called a high luminosity B-factory with a project name 'SuperB'. This project builds on a long history of successful e+e- colliders built around the world, as illustrated in Figure 1.1. The key advances in the design of this accelerator come from recent successes at the DAFNE collider at INFN in Frascati, Italy, at PEP-II at SLAC in California, USA, and at KEKB at KEK in Tsukuba Japan, and from new concepts in beam manipulation at the interaction region (IP) called 'crab waist'. This new collider comprises of two colliding beam rings, one at 4.2 GeV and one at 6.7 GeV, a common interaction region, a new injection system at full beam energies, and one of the two beams longitudinally polarized at the IP. Most of the new accelerator techniques needed for this collider have been achieved at other recently completed accelerators including the new PETRA-3 light source at DESY in Hamburg (Germany) and the upgraded DAFNE collider at the INFN laboratory at Frascati (Italy), or during design studies of CLIC or the International Linear Collider (ILC). The project is to be designed and constructed by a worldwide collaboration of accelerator and engineering staff along with ties to industry. To save significant construction costs, many components from the PEP-II collider at SLAC will be recycled and used in this new accelerator. The interaction region will be designed in collaboration with the particle physics detector to guarantee successful mutual use. The accelerator collaboration will consist of several groups at present universities and national

  6. SuperB: A High-Luminosity Asymmetric e+e- Super Flavor Factory

    SciTech Connect (OSTI)

    Bona, M.; /et al.

    2007-05-18

    We discuss herein the exciting physics program that can be accomplished with a very large sample of heavy quark and heavy lepton decays produced in the very clean environment of an e{sup +}e{sup -} collider; a program complementary to that of an experiment such as LHCb at a hadronic machine. It then presents the conceptual design of a new type of e{sup +}e{sup -} collider that produces a nearly two-order-of-magnitude increase in luminosity over the current generation of asymmetric B Factories. The key idea is the use of low emittance beams produced in an accelerator lattice derived from the ILC Damping Ring Design, together with a new collision region, again with roots in the ILC final focus design, but with important new concepts developed in this design effort. Remarkably, SuperB produces this very large improvement in luminosity with circulating currents and wallplug power similar to those of the current B Factories. There is clear synergy with ILC R&D; design efforts have already influenced one another, and many aspects of the ILC Damping Rings and Final Focus would be operationally tested at SuperB. Finally, the design of an appropriate detector, based on an upgrade of BABAR as an example, is discussed in some detail. A preliminary cost estimate is presented, as is an example construction timeline.

  7. Fuel Economy and Emissions Effects of Low Tire Pressure, Open Windows, Roof Top and Hitch-Mounted Cargo, and Trailer

    SciTech Connect (OSTI)

    Thomas, John F; Huff, Shean P; West, Brian H

    2014-01-01

    To quantify the fuel economy (FE) effect of some common vehicle accessories or alterations, a compact passenger sedan and a sport utility vehicle (SUV) were subjected to SAE J2263 coastdown procedures. Coastdowns were conducted with low tire pressure, all windows open, with a roof top or hitch-mounted cargo carrier, and with the SUV pulling an enclosed cargo trailer. From these coastdowns, vehicle dynamometer coefficients were developed which enabled the execution of vehicle dynamometer experiments to determine the effect of these changes on vehicle FE and emissions over standard drive cycles and at steady highway speeds. The FE penalty associated with the rooftop cargo box mounted on the compact sedan was as high as 25-27% at higher speeds, where the aerodynamic drag is most pronounced. For both vehicles, use of a hitch mounted cargo tray carrying a similar load resulted in very small FE penalties, unlike the rooftop cargo box. The results for the SUV pulling a 3500 pound enclosed cargo trailer were rather dramatic, resulting in FE penalties ranging from 30%, for the city cycle, to 50% at 80 mph, at which point significant CO generation indicated protective enrichment due to high load. Low tire pressure cases resulted in negligible to 10% FE penalty depending on the specific case and test point. Driving with all four windows open decreased FE by 4-8.5% for the compact sedan, and 1-4% for the SUV.

  8. Oblique reconstructions in tomosynthesis. II. Super-resolution

    SciTech Connect (OSTI)

    Acciavatti, Raymond J.; Maidment, Andrew D. A.

    2013-11-15

    Purpose: In tomosynthesis, super-resolution has been demonstrated using reconstruction planes parallel to the detector. Super-resolution allows for subpixel resolution relative to the detector. The purpose of this work is to develop an analytical model that generalizes super-resolution to oblique reconstruction planes.Methods: In a digital tomosynthesis system, a sinusoidal test object is modeled along oblique angles (i.e., pitches) relative to the plane of the detector in a 3D divergent-beam acquisition geometry. To investigate the potential for super-resolution, the input frequency is specified to be greater than the alias frequency of the detector. Reconstructions are evaluated in an oblique plane along the extent of the object using simple backprojection (SBP) and filtered backprojection (FBP). By comparing the amplitude of the reconstruction against the attenuation coefficient of the object at various frequencies, the modulation transfer function (MTF) is calculated to determine whether modulation is within detectable limits for super-resolution. For experimental validation of super-resolution, a goniometry stand was used to orient a bar pattern phantom along various pitches relative to the breast support in a commercial digital breast tomosynthesis system.Results: Using theoretical modeling, it is shown that a single projection image cannot resolve a sine input whose frequency exceeds the detector alias frequency. The high frequency input is correctly visualized in SBP or FBP reconstruction using a slice along the pitch of the object. The Fourier transform of this reconstructed slice is maximized at the input frequency as proof that the object is resolved. Consistent with the theoretical results, experimental images of a bar pattern phantom showed super-resolution in oblique reconstructions. At various pitches, the highest frequency with detectable modulation was determined by visual inspection of the bar patterns. The dependency of the highest detectable

  9. Method and apparatus for connecting high voltage leads to a high temperature super-conducting transformer

    DOE Patents [OSTI]

    Golner, Thomas M.; Mehta, Shirish P.

    2005-07-26

    A method and apparatus for connecting high voltage leads to a super-conducting transformer is provided that includes a first super-conducting coil set, a second super-conducting coil set, and a third super-conducting coil set. The first, second and third super-conducting coil sets are connected via an insulated interconnect system that includes insulated conductors and insulated connectors that are utilized to connect the first, second, and third super-conducting coil sets to the high voltage leads.

  10. Development of asphalts and pavements using recycled tire rubber. Phase 1, Technical feasibility. Technical progress report, September 1, 1994--August 31, 1995

    SciTech Connect (OSTI)

    Bullin, J.A.; Davison, R.R.; Glover, C.J.

    1996-06-01

    About 285 million tires are discarded every year; less than 100 million are currently being recycled, with the rest being placed in landfills and other waste sites. A solution to reduce the littering of the environment is to use ground tire rubber in road construction. Currently, about 27 million tons of asphalt are used each year in road construction and maintenance of the country`s 2 million miles of roads. If all of the waste tire rubber could be combined with asphalt in road construction, it would displace less than 6% of the total asphalt used each year, yet could save about 60 trillion Btus annually. Purpose of this project is to provide data needed to optimize the performance of rubber-asphalt concretes. The first phase is to develop asphalts and recycling agents tailored for compatibility with ground tire rubber. Chapter 2 presents results on Laboratory Testing and Evaluation: fractionate asphalt material, reblending for aromatic asphalts, verifying optimal curing parameters, aging of blends, and measuring ductilities of asphalt-rubber binders. Chapter 3 focuses on Evaluating Mixture Characteristics (modified binders). Chapter 4 covers Adhesion Test Development (water susceptibility is also covered). The final chapter focuses on the Performance/Economic Update and Commercialization Plan.

  11. Actinide targets for the synthesis of super-heavy elements

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Roberto, J.; Alexander, Charles W.; Boll, Rose Ann; Ezold, Julie G.; Felker, Leslie Kevin; Rykaczewski, Krzysztof Piotr; Hogle, Susan L.

    2015-06-18

    Since 2000, six new super-heavy elements with atomic numbers 113 through 118 have been synthesized in hot fusion reactions of 48Ca beams on actinide targets. These target materials, including 242Pu, 244Pu, 243Am, 245Cm, 248Cm, 249Cf, and 249Bk, are available in very limited quantities and require specialized production and processing facilities resident in only a few research centers worldwide. This report describes the production and chemical processing of heavy actinide materials for super-heavy element research, current availabilities of these materials, and related target fabrication techniques. The impact of actinide materials in super-heavy element discovery is reviewed, and strategies for enhancing themore » production of rare actinides including 249Bk, 251Cf, and 254Es are described.« less

  12. Actinide targets for the synthesis of super-heavy elements

    SciTech Connect (OSTI)

    Roberto, J.; Alexander, Charles W.; Boll, Rose Ann; Ezold, Julie G.; Felker, Leslie Kevin; Rykaczewski, Krzysztof Piotr; Hogle, Susan L.

    2015-06-18

    Since 2000, six new super-heavy elements with atomic numbers 113 through 118 have been synthesized in hot fusion reactions of 48Ca beams on actinide targets. These target materials, including 242Pu, 244Pu, 243Am, 245Cm, 248Cm, 249Cf, and 249Bk, are available in very limited quantities and require specialized production and processing facilities resident in only a few research centers worldwide. This report describes the production and chemical processing of heavy actinide materials for super-heavy element research, current availabilities of these materials, and related target fabrication techniques. The impact of actinide materials in super-heavy element discovery is reviewed, and strategies for enhancing the production of rare actinides including 249Bk, 251Cf, and 254Es are described.

  13. Experimental study of the proposed super-thermal-conductor: BAs

    SciTech Connect (OSTI)

    Lv, Bing; Lan, Yucheng; Zhang, Qian; Ren, Zhifeng E-mail: cwchu@uh.edu; Wang, Xiqu; Jacobson, Allan J.; Hu, Yongjie; Chen, Gang; Broido, David; Chu, Ching-Wu E-mail: cwchu@uh.edu

    2015-02-16

    Recent calculations predict a super-thermal-conductivity of ∼2000 Wm{sup −1} K{sup −1}, comparable to that of diamond, in cubic boron arsenide (BAs) crystals, which may offer inexpensive insulators with super-thermal-conductivity for microelectronic device applications. We have synthesized and characterized single crystals of BAs with a zinc blende cubic structure and lattice parameters of a = 4.7830(7) Å. A relatively high thermal conductivity of ∼200 Wm{sup −1} K{sup −1} is obtained, close to those of best non-carbon crystal insulators, such as SiC, although still an order of magnitude smaller than the value predicted. Based on our XPS, X-ray single crystal diffraction, and Raman scattering results, steps to achieve the predicted super-thermal conductivity in BAs are proposed.

  14. An overview of SuperLU: Algorithms, implementation, and userinterface

    SciTech Connect (OSTI)

    Li, Xiaoye S.

    2003-09-30

    We give an overview of the algorithms, design philosophy,and implementation techniques in the software SuperLU, for solving sparseunsymmetric linear systems. In particular, we highlight the differencesbetween the sequential SuperLU (including its multithreaded extension)and parallel SuperLU_DIST. These include the numerical pivoting strategy,the ordering strategy for preserving sparsity, the ordering in which theupdating tasks are performed, the numerical kernel, and theparallelization strategy. Because of the scalability concern, theparallel code is drastically different from the sequential one. Wedescribe the user interfaces ofthe libraries, and illustrate how to usethe libraries most efficiently depending on some matrix characteristics.Finally, we give some examples of how the solver has been used inlarge-scale scientific applications, and the performance.

  15. TRANSITION CROSSING FOR THE BNL SUPER NEUTRINO BEAM FACILITY.

    SciTech Connect (OSTI)

    WEI,J.TSOUPAS,N.

    2004-07-05

    The super neutrino beam facility proposed at the Brookhaven National Laboratory requires proton beams to cross the transition energy in the AGS to reach 1 MW beam power at top energy. High intensity beams are accelerated at a fast repetition rate. Upon transition crossing, such high intensity bunches of large momentum spreads suffer from strong nonlinear chromatic effects and self-field effects. Using theoretical and experimental methods, we determine the impact of these effects and the effectiveness of transition-jump compensation schemes, and determine the optimum crossing scenario for the super neutrino beam facility.

  16. Super Water-Repellant Coatings Can Now Take the Pressure | U...

    Office of Science (SC) Website

    Super Water-Repellant Coatings Can Now Take the Pressure Basic Energy Sciences (BES) BES ... Super Water-Repellant Coatings Can Now Take the Pressure Careful tuning of a surface at ...

  17. Non-uniform Aging on Super Duty Diesel Truck Aged Urea Cu/Zeolite...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Aging on Super Duty Diesel Truck Aged Urea CuZeolite SCR Catalysts Non-uniform Aging on Super Duty Diesel Truck Aged Urea CuZeolite SCR Catalysts CuZeolite SCR catalysts aged ...

  18. Intense Super-radiant X-rays from a Compact Source using a Nanocathode...

    Office of Scientific and Technical Information (OSTI)

    Intense Super-radiant X-rays from a Compact Source using a Nanocathode Array and Emittance Exchange Citation Details In-Document Search Title: Intense Super-radiant X-rays from a ...

  19. SuperTruck … Development and Demonstration of a Fuel-Efficient...

    Energy Savers [EERE]

    SuperTruck Development and Demonstration of a Fuel-Efficient Class 8 Tractor & Trailer SuperTruck Development and Demonstration of a Fuel-Efficient Class 8 Tractor & Trailer ...

  20. Shiloh III | Open Energy Information

    Open Energy Info (EERE)

    Shiloh III Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner enXco Developer EnXco Energy Purchaser Pacific Gas & Electric Co Location...

  1. Daimler's SuperTruck Program; 50% Brake Thermal Efficiency | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Daimler's SuperTruck Program; 50% Brake Thermal Efficiency Daimler's SuperTruck Program; 50% Brake Thermal Efficiency Presents highlights of engine and vehicle advances made, and progress towards achieving aggressive goals deer12_sisken.pdf (2.38 MB) More Documents & Publications Vehicle Technologies Office Merit Review 2015: SuperTruck Program: Engine Project Review SuperTruck Program: Engine Project Review Supertruck - Improving Transportation Efficiency through Integrated

  2. Argonne OutLoud: Rise of the Super Smart Supercomputer (March 14, 2013) |

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Argonne National Laboratory Rise of the Super Smart Supercomputer (March 14, 2013) Share Pete Beckman

  3. DOE Announces $80 Million in Funding to Increase SuperTruck Efficiency |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Announces $80 Million in Funding to Increase SuperTruck Efficiency DOE Announces $80 Million in Funding to Increase SuperTruck Efficiency March 1, 2016 - 2:59pm Addthis News release from the Department of Energy WASHINGTON - Building on the notable successes of the SuperTruck initiative, Deputy Assistant Secretary for Transportation Reuben Sarkar today announced SuperTruck II, an $80 million funding opportunity, subject to congressional appropriations, for research,

  4. Super_Prompt Crit excursions in Sph Geometry

    Energy Science and Technology Software Center (OSTI)

    2000-03-17

    AX-TNT solves (a) the coupled hydrodynamic, thermodynamical neutronic equations which describe a spherical, super prompt critical reactor system during an excursion. (b) the coupled equations of motion, and ideal gas equation of state for the detonation of a spherical charge in a gas.

  5. Computer protection plan for the Superconducing Super Collider Laboratory

    SciTech Connect (OSTI)

    Hunter, S.

    1992-04-15

    The purpose of this document is to describe the current unclassified computer security program practices, Policies and procedures for the Superconducting Super Collider Laboratory (SSCL). This document includes or references all related policies and procedures currently implemented throughout the SSCL. The document includes security practices which are planned when the facility is fully operational.

  6. Super Boiler: First Generation, Ultra-High Efficiency Firetube Boiler

    SciTech Connect (OSTI)

    2006-06-01

    This factsheet describes a research project whose goal is to develop and demonstrate a first-generation ultra-high-efficiency, ultra-low emissions, compact gas-fired package boiler (Super Boiler), and formulate a long-range RD&D plan for advanced boiler technology out to the year 2020.

  7. Nitriding of super alloys for enhancing physical properties

    DOE Patents [OSTI]

    Purohit, A.

    1984-06-25

    The invention teaches the improvement of certain super alloys by exposing the alloy to an atmosphere of elemental nitrogen at elevated temperatures in excess of 750/sup 0/C but less than 1150/sup 0/C for an extended duration, viz., by nitriding the surface of the alloy, to establish barrier nitrides of the order of 25 to 100 micrometers thickness. These barrier

  8. Superconducting Super Collider Magnet System requirements. Revision A

    SciTech Connect (OSTI)

    1986-10-23

    This report discusses the Superconducting Super Collider magnet system requirements when the following categories: Functions; operational performance requirements; system configuration and essential features; structural requirements; availability/reliability; instrumentation and control requirements; design life; environment; maintenance requirements; interface systems; quality assurance; safety; and applicable codes and standards.

  9. Cosmic super-strings and Kaluza-Klein modes

    SciTech Connect (OSTI)

    Dufaux, Jean-Franois

    2012-09-01

    Cosmic super-strings interact generically with a tower of relatively light and/or strongly coupled Kaluza-Klein (KK) modes associated with the geometry of the internal space. In this paper, we study the production of spin-2 KK particles by cusps on loops of cosmic F- and D-strings. We consider cosmic super-strings localized either at the bottom of a warped throat or in a flat internal space with large volume. The total energy emitted by cusps in KK modes is comparable in both cases, although the number of produced KK modes may differ significantly. We then show that KK emission is constrained by the photo-dissociation of light elements and by observations of the diffuse gamma ray background. We show that this rules out regions of the parameter space of cosmic super-strings that are complementary to the regions that can be probed by current and upcoming gravitational wave experiments. KK modes are also expected to play an important role in the friction-dominated epoch of cosmic super-string evolution.

  10. Statistical properties of super-hot solar flares

    SciTech Connect (OSTI)

    Caspi, Amir; Krucker, Sm; Lin, R. P.

    2014-01-20

    We use Reuven Ramaty High Energy Solar Spectroscopic Imager (RHESSI) high-resolution imaging and spectroscopy observations from ?6 to 100 keV to determine the statistical relationships between measured parameters (temperature, emission measure, etc.) of hot, thermal plasma in 37 intense (GOES M- and X-class) solar flares. The RHESSI data, most sensitive to the hottest flare plasmas, reveal a strong correlation between the maximum achieved temperature and the flare GOES class, such that 'super-hot' temperatures >30 MK are achieved almost exclusively by X-class events; the observed correlation differs significantly from that of GOES-derived temperatures, and from previous studies. A nearly ubiquitous association with high emission measures, electron densities, and instantaneous thermal energies suggests that super-hot plasmas are physically distinct from cooler, ?10-20 MK GOES plasmas, and that they require substantially greater energy input during the flare. High thermal energy densities suggest that super-hot flares require strong coronal magnetic fields, exceeding ?100 G, and that both the plasma ? and volume filling factor f cannot be much less than unity in the super-hot region.

  11. Observation of super-resolution in digital breast tomosynthesis

    SciTech Connect (OSTI)

    Acciavatti, Raymond J.; Maidment, Andrew D. A.

    2012-12-15

    Purpose: Digital breast tomosynthesis (DBT) is a 3D x-ray imaging modality in which tomographic sections of the breast are generated from a limited range of tube angles. Because oblique x-ray incidence shifts the image of an object in subpixel detector element increments with each increasing projection angle, it is demonstrated that DBT is capable of super-resolution (i.e., subpixel resolution). Methods: By convention, DBT reconstructions are performed on planes parallel to the breast support at various depths of the breast volume. In order for resolution in each reconstructed slice to be comparable to the detector, the pixel size should match that of the detector elements; hence, the highest frequency that can be resolved in the plane of reconstruction is the alias frequency of the detector. This study considers reconstruction grids with much smaller pixelation to visualize higher frequencies. For analytical proof of super-resolution, a theoretical framework is developed in which the reconstruction of a high frequency sinusoidal input is calculated using both simple backprojection (SBP) and filtered backprojection. To study the frequency spectrum of the reconstruction, its Fourier transform is also determined. The experimental feasibility of super-resolution was investigated by acquiring images of a bar pattern phantom with frequencies higher than the detector alias frequency. Results: Using analytical modeling, it is shown that the central projection cannot resolve frequencies exceeding the detector alias frequency. The Fourier transform of the central projection is maximized at a lower frequency than the input as evidence of aliasing. By contrast, SBP reconstruction can resolve the input, and its Fourier transform is correctly maximized at the input frequency. Incorporating filters into the reconstruction smoothens pixelation artifacts in the spatial domain and reduces spectral leakage in the Fourier domain. It is also demonstrated that the existence of super

  12. Photo of the Week: Inside the Super HILAC | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Super HILAC Photo of the Week: Inside the Super HILAC August 29, 2013 - 2:55pm Addthis Super HILAC (Super Heavy Ion Linear Accelerator) was one of the first particle accelerators that could accelerate heavier elements to “atom-smashing” speeds. The device was built in 1972 and played a significant role in four decades of scientific research at Lawrence Berkeley National Laboratory. In addition to being the launchpad for a variety of major experiments, the Super HILAC was crucial in the

  13. Hybrid (particle in cell-fluid) simulation of ion-acoustic soliton generation including super-thermal and trapped electrons

    SciTech Connect (OSTI)

    Nopoush, M.; Abbasi, H.

    2011-08-15

    The present paper is devoted to the simulation of the nonlinear disintegration of a localized perturbation into an ion-acoustic soliton in a plasma. Recently, this problem was studied by a simple model [H. Abbasi et al., Plasma Phys. Controlled Fusion 50, 095007 (2008)]. The main assumptions were (i) in the electron velocity distribution function (DF), the ion-acoustic soliton velocity was neglected in comparison to the electron thermal velocity, (ii) on the ion-acoustic evolution time-scale, the electron velocity DF was assumed to be stationary, and (iii) the calculation was restricted to the small amplitude case. In order to generalize the model, one has to consider the evolution of the electron velocity DF for finite amplitudes. For this purpose, a one dimensional electrostatic hybrid code, particle in cell (PIC)-fluid, was designed. It simulates the electrons dynamics by the PIC method and the cold ions dynamics by the fluid equations. The plasma contains a population of super-thermal electrons and, therefore, a Lorentzian (kappa) velocity DF is used to model the high energy tail in the electron velocity DF. Electron trapping is included in the simulation in view of their nonlinear resonant interaction with the localized perturbation. A Gaussian initial perturbation is used to model the localized perturbation. The influence of both the trapped and the super-thermal electrons on this process is studied and compared with the previous model.

  14. Acetylene from the co-pyrolysis of biomass and waste tires or coal in the H{sub 2}/Ar plasma

    SciTech Connect (OSTI)

    Bao, W.; Cao, Q.; Lv, Y.; Chang, L.

    2008-07-01

    Acetylene from carbon-containing materials via plasma pyrolysis is not only simple but also environmentally friendly. In this article, the acetylene produced from co-pyrolyzing biomass with waste tire or coal under the conditions of H{sub 2}/Ar DC arc plasma jet was investigated. The experimental results showed that the co-pyrolysis of mixture with biomass and waste tire or coal can improve largely the acetylene relative volume fraction (RVF) in gaseous products and the corresponding yield of acetylene. The change trends for the acetylene yield of plasma pyrolysis from mixture with raw sample properties were the same as relevant RVF. But the yield change trend with feeding rate is different from its RVF. The effects of the feeding rate of raw materials and the electric current of plasmatron on acetylene formation are also discussed.

  15. Longitudinal Beam Stability in the SUPER B-FACTORY

    SciTech Connect (OSTI)

    Novokhatski, A.; Zobov, M.; /Frascati

    2009-07-06

    We give an overview of wake fields and impedances in a proposed Super B project, which is based on extremely low emittance beams colliding at a large angle with a crab waist transformation. Understanding the effects that wake fields have on the beam is critical for a successful machine operation. We use our combined experience from the operation of the SLAC B-factory and DA{Phi}NE {Phi}-factory to eliminate strong HOM sources and minimize the chamber impedance in the Super B design. Based on a detailed study of the wake fields in this design we have developed a quasi-Green's function for the entire ring that is used to study bunch lengthening and beam stability. In particular, we check the stability threshold using numerical solutions of the Fokker-Plank equation. We also make a comparison of numerical simulations with the bunch lengthening data in the B- factory.

  16. Presentations to the SuperHILAC Program Advisory Committee

    SciTech Connect (OSTI)

    McDonald, R.J.

    1987-09-01

    This paper contains viewgraphs on the SuperHILAC. The topics of these viewgraphs are: light charged particle emission as a probe of heavy-ion reactions; correlated charged-changing interactions and x-ray emission in ion-atom collisions; progress report on Sassy II and new nuclear chemistry experiments at the SuperHILAC; precision x-ray spectroscopy of heavy ions; 180/sup 0/-correlated equal energy photons from 5.9 MeV/N U + Th collisions; research statement of excited states of monatomic and molecular systems; search for entrance-channel effects in the production of superdeformed nuclei; present and future research with OASIS; relaxation mechanisms in damped heavy-ion reactions; excitation energy division and nucleon transfer; test of QED and relativistic effects for strongly-bound electrons; heavy-ion Coulomb excitation and transfer reactions as probes of nuclear structure; and preliminary design of the Dilepton spectrometer.

  17. Wake Fields in the Super B Factory Interaction Region

    SciTech Connect (OSTI)

    Weathersby, Stephen; Novokhatski, Alexander; /SLAC

    2011-06-02

    The geometry of storage ring collider interaction regions present an impedance to beam fields resulting in the generation of additional electromagnetic fields (higher order modes or wake fields) which affect the beam energy and trajectory. These affects are computed for the Super B interaction region by evaluating longitudinal loss factors and averaged transverse kicks for short range wake fields. Results indicate at least a factor of 2 lower wake field power generation in comparison with the interaction region geometry of the PEP-II B-factory collider. Wake field reduction is a consderation in the Super B design. Transverse kicks are consistent with an attractive potential from the crotch nearest the beam trajectory. The longitudinal loss factor scales as the -2.5 power of the bunch length. A factor of 60 loss factor reduction is possible with crotch geometry based on an intersecting tubes model.

  18. Spontaneous supersymmetry breaking in two dimensional lattice super QCD

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Catterall, Simon; Veernala, Aarti

    2015-10-02

    We report on a non-perturbative study of two dimensional N=(2,2) super QCD. Our lattice formulation retains a single exact supersymmetry at non-zero lattice spacing, and contains Nf fermions in the fundamental representation of a U(Nc) gauge group. The lattice action we employ contains an additional Fayet-Iliopoulos term which is also invariant under the exact lattice supersymmetry. This work constitutes the first numerical study of this theory which serves as a toy model for understanding some of the issues that are expected to arise in four dimensional super QCD. As a result, we present evidence that the exact supersymmetry breaks spontaneouslymore » when Nf < Nc in agreement with theoretical expectations.« less

  19. Spontaneous supersymmetry breaking in two dimensional lattice super QCD

    SciTech Connect (OSTI)

    Catterall, Simon; Veernala, Aarti

    2015-10-02

    We report on a non-perturbative study of two dimensional N=(2,2) super QCD. Our lattice formulation retains a single exact supersymmetry at non-zero lattice spacing, and contains Nf fermions in the fundamental representation of a U(Nc) gauge group. The lattice action we employ contains an additional Fayet-Iliopoulos term which is also invariant under the exact lattice supersymmetry. This work constitutes the first numerical study of this theory which serves as a toy model for understanding some of the issues that are expected to arise in four dimensional super QCD. As a result, we present evidence that the exact supersymmetry breaks spontaneously when Nf < Nc in agreement with theoretical expectations.

  20. An active metallic nanomatryushka with two similar super-resonances

    SciTech Connect (OSTI)

    Wu, D. J.; Cheng, Y.; Wu, X. W.; Liu, X. J.

    2014-07-07

    The optical properties of a simple metallic nanomatryushka (nanosphere-in-a-nanoshell) with gain have been investigated theoretically. The spaser (surface plasmon amplification by stimulated emission of radiation) phenomena can be observed at two critical wavelengths in the active metallic nanomatryushkas. With increasing the gain coefficient of the middle layer, a similar super surface plasmon (SP) resonance is first found at the ???|? mode of the active nanoparticles and then breaks down. With further increasing the gain coefficient, another similar super-resonance occurs at the ???|? mode. The near-field enhancements in the active nanomatryushkas also have been greatly amplified at the critical wavelengths for ???|? and ???|? modes. It is further found that the amplifications of SPs in the active AgSiO?Au nanoshell are strongest in four kinds of nanoshells and hence the largest near fields. The giant near-field enhancement can greatly enhance the Raman excitation and emission.

  1. High speed data transmission at the Superconducting Super Collider

    SciTech Connect (OSTI)

    Leskovar, B.

    1990-04-01

    High speed data transmission using fiber optics in the data acquisition system of the Superconducting Super Collider has been investigated. Emphasis is placed on the high speed data transmission system overview, the local data network and on subassemblies, such as optical transmitters and receivers. Also, the performance of candidate subassemblies having a low power dissipation for the data acquisition system is discussed. 14 refs., 5 figs.

  2. Cummins SuperTruck Program - Technology Demonstration of Highly Efficient

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Clean, Diesel Powered Class 8 Trucks | Department of Energy Demonstration of Highly Efficient Clean, Diesel Powered Class 8 Trucks Cummins SuperTruck Program - Technology Demonstration of Highly Efficient Clean, Diesel Powered Class 8 Trucks Low temperature combustion at part load combined with diffusion controlled combustion at higher loads, and robust control system dynamically adjusting engine operation, maximize engine efficiency while meeting tailpipe emissions standards

  3. IdentityMap Visualization of the Super Identity Model

    SciTech Connect (OSTI)

    2015-04-15

    The Super Identity Model is a collaboration with six United Kingdom universities to develop use cases used to piece together a person's identity across biological, cyber, psychological, and biographical domains. PNNL visualized the model in a web-based application called IdentityMap. This is the first step in a promising new field of research. Interested future collaborators are welcome to find out more by emailing superid@pnnl.gov.

  4. Title III hazardous air pollutants

    SciTech Connect (OSTI)

    Todd, R.

    1995-12-31

    The author presents an overview of the key provisions of Title III of the Clean Air Act Amendments of 1990. The key provisions include the following: 112(b) -- 189 Hazardous Air Pollutants (HAP); 112(a) -- Major Source: 10 TPY/25 TPY; 112(d) -- Application of MACT; 112(g) -- Modifications; 112(I) -- State Program; 112(j) -- The Hammer; and 112(r) -- Accidental Release Provisions.

  5. WCI-III Workshop Recap

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    WCI-III Recap Workshop Information Program Schedule Registration List Announcement Letter Tentative Outline for Book Steering Committee Presentation Files (Power Point or PDF) Saturday (Morning, Afternoon) Sunday (Morning, Afternoon) Monday (Morning, Afternoon) Tuesday (Morning, Afternoon) Wednesday (Morning, Afternoon) Misc. Pictures

  6. The SuperB Accelerator: Overview and Lattice Studies

    SciTech Connect (OSTI)

    Biagini, M.E.; Boni, R.; Boscolo, M.; Drago, A.; Guiducci, S.; Preger, M.; Raimondi, P.; Tomassini, S.; Vaccarezza, C.; Zobov, M.; Cai, Y.; Fisher, A.; Heifets, S.; Novokhatski, A.; Pivi, M.T.; Seeman, J.; Sullivan, M.; Wienands, U.; Paoloni, E.; Marchiori, G.; Koop, I.; /Novosibirsk, IYF /Daresbury /LBL, Berkeley /CERN /Orsay, LAL /KEK, Tsukuba

    2011-11-22

    SuperB aims at the construction of a very high luminosity (10{sup 36} cm{sup -2} s{sup -1}) asymmetric e{sup +}e{sup -} Flavour Factory, with possible location at the campus of the University of Rome Tor Vergata, near the INFN Frascati National Laboratory. In this paper the basic principles of the design and details on the lattice are given. SuperB is a new machine that can exploit novel very promising design approaches: (1) large Piwinski angle scheme will allow for peak luminosity of the order of 10{sup 36} cm{sup -2} s{sup -1}, well beyond the current state-of-the-art, without a significant increase in beam currents or shorter bunch lengths; (2) 'crab waist' sextupoles will be used for suppression of dangerous resonances; (3) the low beam currents design presents reduced detector and background problems, and affordable operating costs; (4) a polarized electron beam can produce polarized {tau} leptons, opening an entirely new realm of exploration in lepton flavor physics. SuperB studies are already proving useful to the accelerator and particle physics communities. The principle of operation is being tested at DAFNE. The baseline lattice, based on the reuse of all PEP-II hardware, fits in the Tor Vergata University campus site, near Frascati. A CDR is being reviewed by an International Review Committee, chaired by J. Dainton (UK). A Technical Design Report will be prepared to be ready by beginning of 2010.

  7. Audit of controls over Superconducting Super Collider Laboratory subcontractor expenditures

    SciTech Connect (OSTI)

    Not Available

    1993-10-22

    In January 1989 the Department of Energy contracted with Universities Research Association, Inc. to design, construct, manage, operate, and maintain the Superconducting Super Collider Laboratory. Through Fiscal Year 1992, costs for subcontractor goods and services accounted for about 75 percent of the Superconducting Super Collider Laboratory expenditures. The Office of Inspector General evaluated the adequacy of controls in place to ensure that subcontractor costs were reasonable, as required by the contract. The following conclusions were drawn from the audit. The Superconducting Super Collider Laboratory did not consistently exercise prudent business judgment in making subcontractor expenditures. As a result, $60 million in expenditures already made and $128 million planned with commercial subcontractors were, in the authors opinion, unnecessary, excessive, or represented uncontrolled growth. The audit also found inadequate justifications, accountability, and cost controls over $143 million in expenditures made and $47 million planned with other Department of Energy laboratories. Improvements were needed in subcontract administration and internal controls, including appropriate audit coverage of the subcontracts. In addition, Department of Energy guidance concerning procurement actions between the laboratories needed to be established.

  8. VHTR Prismatic Super Lattice Model for Equilibrium Fuel Cycle Analysis

    SciTech Connect (OSTI)

    G. S. Chang

    2006-09-01

    The advanced Very High Temperature gas-cooled Reactor (VHTR), which is currently being developed, achieves simplification of safety through reliance on innovative features and passive systems. One of the VHTRs innovative features is the reliance on ceramic-coated fuel particles to retain the fission products under extreme accident conditions. The effect of the random fuel kernel distribution in the fuel prismatic block is addressed through the use of the Dancoff correction factor in the resonance treatment. However, if the fuel kernels are not perfect black absorbers, the Dancoff correction factor is a function of burnup and fuel kernel packing factor, which requires that the Dancoff correction factor be updated during Equilibrium Fuel Cycle (EqFC) analysis. An advanced Kernel-by-Kernel (K-b-K) hexagonal super lattice model can be used to address and update the burnup dependent Dancoff effect during the EqFC analysis. The developed Prismatic Super Homogeneous Lattice Model (PSHLM) is verified by comparing the calculated burnup characteristics of the double-heterogeneous Prismatic Super Kernel-by-Kernel Lattice Model (PSK-b-KLM). This paper summarizes and compares the PSHLM and PSK-b-KLM burnup analysis study and results. This paper also discusses the coupling of a Monte-Carlo code with fuel depletion and buildup code, which provides the fuel burnup analysis tool used to produce the results of the VHTR EqFC burnup analysis.

  9. Linear relationship between water wetting behavior and microscopic interactions of super-hydrophilic surfaces

    SciTech Connect (OSTI)

    Liu, Jian; Guo, Pan; University of Chinese Academy of Sciences, Beijing 100049 ; Wang, Chunlei; Shi, Guosheng Fang, Haiping

    2013-12-21

    Using molecular dynamics simulations, we show a fine linear relationship between surface energies and microscopic Lennard-Jones parameters of super-hydrophilic surfaces. The linear slope of the super-hydrophilic surfaces is consistent with the linear slope of the super-hydrophobic, hydrophobic, and hydrophilic surfaces where stable water droplets can stand, indicating that there is a universal linear behavior of the surface energies with the water-surface van der Waals interaction that extends from the super-hydrophobic to super-hydrophilic surfaces. Moreover, we find that the linear relationship exists for various substrate types, and the linear slopes of these different types of substrates are dependent on the surface atom density, i.e., higher surface atom densities correspond to larger linear slopes. These results enrich our understanding of water behavior on solid surfaces, especially the water wetting behaviors on uncharged super-hydrophilic metal surfaces.

  10. NIF Title III engineering plan

    SciTech Connect (OSTI)

    Deis, G

    1998-06-01

    The purpose of this document is to define the work that must be accomplished by the NIF Project during Title III Engineering. This definition is intended to be sufficiently detailed to provide a framework for yearly planning, to clearly identify the specific deliverables so that the Project teams can focus on them, and to provide a common set of objectives and processes across the Project. This plan has been preceded by similar documents for Title I and Title II design and complements the Site Management Plan, the Project Control Manual, the Quality Assurance Program Plan, the RM Parsons NIF Title III Configuration Control Plan, the Integrated Project Schedule, the Preliminary Safety Analysis Report, the Configuration Management Plan, and the Transition Plan.

  11. Altech III (b) | Open Energy Information

    Open Energy Info (EERE)

    b) Jump to: navigation, search Name Altech III (b) Facility Altech III Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner SeaWest Developer...

  12. GRED III Phase II | Open Energy Information

    Open Energy Info (EERE)

    2010 DOI Not Provided Check for DOI availability: http:crossref.org Online Internet link for GRED III Phase II Citation Bernie Karl. 2010. GRED III Phase II. p....

  13. Pulmonary function and symptoms of Nigerian workers exposed to carbon black in dry cell battery and tire factories

    SciTech Connect (OSTI)

    Oleru, U.G.; Elegbeleye, O.O.; Enu, C.C.; Olumide, Y.M.

    1983-02-01

    The pulmonary function and symptoms of 125 workers exposed to carbon black in dry cell battery and tire manufacturing plants were investigated. There was no significant difference in the pulmonary function of the subjects in the two plants. There was good agreement in the symptoms reported in the two different factories: cough with phlegm production, tiredness, chest pain, catarrh, headache, and skin irritation. The symptoms also corroborate those reported in the few studies on the pulmonary effects of carbon black. The suspended particulate levels in the dry cell battery plant ranged from 25 to 34 mg/m/sup 3/ and the subjects with the highest probable exposure level had the most impaired pulmonary function. The pulmonary function of the exposed subjects was significantly lower than that of a control, nonindustrially exposed population. The drop in the lung function from the expected value per year of age was relatively constant for all the study subgroups but the drop per year of duration of employment was more severe in the earlier years of employment. This study has underscored the need for occupational health regulations in the industries of developing countries.

  14. William A. Goddard III - JCAP

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    william a. goddard iii Principal Investigator Email: wag@wag.caltech.edu Dr. Goddard is a pioneer in developing methods for quantum mechanics (QM), force fields, molecular dynamics (MD), and Monte Carlo predictions on chemical and materials systems and is actively involved in applying these methods to ceramics, semiconductors, superconductors, thermoelectrics, metal alloys, polymers, proteins, nuclei acids, Pharma ligands, nanotechnology, and energetic materials. He uses QM methods to determine

  15. Thomas Francis Miller III - JCAP

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    THOMAS FRANCIS MILLER III Principal Investigator Email: tfm@caltech.edu Dr. Miller's research group develops theoretical and computational methods to understand a variety of molecular processes, including enzyme catalysis, solar-energy conversion, dendrite formation in lithium batteries, and the dynamics of soft matter and biological systems. An important aspect of this challenge is that many systems exhibit dynamics that couple vastly different timescales and lengthscales. A primary goal of

  16. SUPPLEMENT III REGARDING APPLICATION SUBMISSION

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    III REGARDING APPLICATION SUBMISSION SCHEDULE FOR: ADVANCED NUCLEAR ENERGY PROJECTS U.S. Department of Energy Loan Programs Office (As of January 19, 2016) THIRD SUPPLEMENT TO LOAN GUARANTEE SOLICITATION ANNOUNCEMENT FEDERAL LOAN GUARANTEES FOR ADVANCED NUCLEAR ENERGY PROJECTS Solicitation Number: DE-SOL- DE-SOL-0007791 OMB Control Number: 1910-5134; OMB Expiration Date 11/30/2016 Announcement Type: Supplemental Supplement Date: January 19, 2016 The above-referenced Loan Guarantee Solicitation

  17. Joel W. Ager III - JCAP

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    w. ager iii Principal Investigator Email: jwager@lbl.gov Dr. Ager's research interests include the fundamental electronic and transport characteristics of photovoltaic materials, development of new photoanodes and photocathodes based on abundant elements for solar fuels production, and the development of new oxide- and sulfide-based transparent conductors. In JCAP, Dr. Ager is investigating interactions of carbon-based supports with CO2-reduction electrocatalysts. His group is studying

  18. Registration List - WCI-III

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    WCI-III Registration List Sandro Barlini, INFN - Laboratori Nazionali di Legnaro Wolfgang Bauer, Michigan State Aldo Bonasera, Laboratorio Nazionale del Sud, INFN Alexander Botvina, Institute for Nuclear Research RAS, Moscow Kyrill Bugaev, Lawrence Berkeley National Laboratory Xavier Campi, LPTMS Abdou Chbihi, GANIL Philippe Chomaz, GANIL Marco Cinausero, INFN Laboratori Nazionali di Legnaro Gianluca Colo', Dipartimento di Fisica Romualdo deSouza, Indiana University/IUCF Massimo Di Toro,

  19. U.S. Department of Energy and SuperPower, Inc. Increase Energy Efficiency

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    in the Nation's Electric Grid | Department of Energy SuperPower, Inc. Increase Energy Efficiency in the Nation's Electric Grid U.S. Department of Energy and SuperPower, Inc. Increase Energy Efficiency in the Nation's Electric Grid February 21, 2008 - 11:29am Addthis $27 Million Project Demonstrates Advanced Superconductivity Technology ALBANY, NY- The U.S. Department of Energy (DOE) and SuperPower, Inc. today commemorated the Albany High-Temperature Superconducting (HTS) Cable Project, the

  20. U.S. Department of Energy and SuperPower, Inc. Increase Energy Efficiency

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    in the Nation's Electric Grid | Department of Energy and SuperPower, Inc. Increase Energy Efficiency in the Nation's Electric Grid U.S. Department of Energy and SuperPower, Inc. Increase Energy Efficiency in the Nation's Electric Grid February 21, 2008 - 11:46am Addthis $27 Million Project Demonstrates Advanced Superconductivity Technology ALBANY, NY- The U.S. Department of Energy (DOE) and SuperPower, Inc. today commemorated the Albany High-Temperature Superconducting (HTS) Cable Project,

  1. High Efficient Clean Combustion for SuperTruck | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    High Efficient Clean Combustion for SuperTruck High Efficient Clean Combustion for SuperTruck Presentation given at the 16th Directions in Engine-Efficiency and Emissions Research (DEER) Conference in Detroit, MI, September 27-30, 2010. deer10_stanton.pdf (1.76 MB) More Documents & Publications Supertruck technologies for 55% thermal efficiency and 68% freight efficiency Cummins SuperTruck Program - Technology Demonstration of Highly Efficient Clean, Diesel Powered Class 8 Trucks Technology

  2. Point spread function of the optical needle super-oscillatory lens

    SciTech Connect (OSTI)

    Roy, Tapashree; Rogers, Edward T. F.; Yuan, Guanghui; Zheludev, Nikolay I.

    2014-06-09

    Super-oscillatory optical lenses are known to achieve sub-wavelength focusing. In this paper, we analyse the imaging capabilities of a super-oscillatory lens by studying its point spread function. We experimentally demonstrate that a super-oscillatory lens can generate a point spread function 24% smaller than that dictated by the diffraction limit and has an effective numerical aperture of 1.31 in air. The object-image linear displacement property of these lenses is also investigated.

  3. John H. Hale III | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    John H. Hale III About Us John H. Hale III - Director, Office of Small and Disadvantaged Business Utilization John H. Hale III Career Highlights Hale is the former Deputy Associate Administrator for the Office of Capital Access at the U.S. Small Business Administration (SBA). In that role, he managed the agency's operations and initiatives designed to enhance customer service for its internal and external stakeholders. John Hale III is the Director of the Office of Small and Disadvantaged

  4. SuperTruck Team Achieves 115% Freight Efficiency Improvement in Class 8

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Long-Haul Truck | Department of Energy SuperTruck Team Achieves 115% Freight Efficiency Improvement in Class 8 Long-Haul Truck SuperTruck Team Achieves 115% Freight Efficiency Improvement in Class 8 Long-Haul Truck April 2, 2015 - 10:49am Addthis SuperTruck Team Achieves 115% Freight Efficiency Improvement in Class 8 Long-Haul Truck Last week, the Vehicle Technologies Office's (VTO) SuperTruck project broke another record in efficiency for Class 8 tractor-trailers. While the original

  5. SuperTruck … Development and Demonstration of a Fuel-Efficient...

    Broader source: Energy.gov (indexed) [DOE]

    More Documents & Publications SuperTruck Development and Demonstration of a Fuel-Efficient Class 8 Tractor & Trailer Supertruck - Development and Demonstration of a ...

  6. U.S. Department of Energy and SuperPower, Inc. Increase Energy...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    The U.S. Department of Energy (DOE) and SuperPower, Inc. today commemorated the Albany ... More Documents & Publications Albany HTS Power Cable Superconductivity Program Overview ...

  7. A Carbon Flux Super Site. New Insights and InnovativeAtmosphere...

    Office of Scientific and Technical Information (OSTI)

    A Carbon Flux Super Site. New Insights and Innovative Atmosphere-Terrestrial Carbon Exchange Measurements and Modeling Citation Details In-Document Search Title: A Carbon Flux ...

  8. Video: SuperTruck Barreling Down the Road of Sustainability | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy SuperTruck Barreling Down the Road of Sustainability Video: SuperTruck Barreling Down the Road of Sustainability May 14, 2015 - 4:30pm Addthis New Energy 101 video shows how the Energy Department's SuperTruck initiative is making Class 8 trucks more fuel efficient and less expensive to operate. | Office of Energy Efficiency and Renewable Energy video. Paul Lester Paul Lester Digital Content Specialist, Office of Public Affairs KEY FACTS SuperTruck initiative helping make Class 8

  9. SuperTruck Making Leaps in Fuel Efficiency | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SuperTruck Making Leaps in Fuel Efficiency SuperTruck Making Leaps in Fuel Efficiency February 26, 2014 - 12:00am Addthis Pedestrians passing by the Energy Department headquarters in Washington, D.C., on February 19 saw quite a strange sight - an ultra-modern 18-wheeler, Class 8 tractor-trailer parked outside the headquarters building. This is no ordinary truck - €it' s called a SuperTruck, a demonstration vehicle that is part of the Energy Department's SuperTruck initiative. This program's

  10. PIK M.S. Onegin Petersburg Nuclear Physics Institute 2015 Super...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    isotopes production in high-flux reactor PIK M.S. Onegin Petersburg Nuclear Physics Institute 2015 Super Heavy Elements Symposium Reactor PIK 2011 - Criticality reached 2013 - ...

  11. U.S. Department of Energy and SuperPower, Inc. Increase Energy Efficiency

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    in the Nation's Electric Grid | Department of Energy and SuperPower, Inc. Increase Energy Efficiency in the Nation's Electric Grid U.S. Department of Energy and SuperPower, Inc. Increase Energy Efficiency in the Nation's Electric Grid The U.S. Department of Energy (DOE) and SuperPower, Inc. today commemorated the Albany High-Temperature Superconducting (HTS) Cable Project, the world's first use of second-generation HTS wire on the grid. U.S. Department of Energy and SuperPower, Inc. Increase

  12. Synchrotron X-ray Studies of Super-critical Carbon Dioxide /...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Synchrotron X-ray Studies of Super-critical Carbon Dioxide Reservoir Rock Interfaces Project obectives: Utilize synchrotron X-ray measurements, to monitor all aspects of atomic ...

  13. Kotzebue Wind Project Phase II & III | Open Energy Information

    Open Energy Info (EERE)

    II & III Jump to: navigation, search Name Kotzebue Wind Project Phase II & III Facility Kotzebue Wind Project Phase II & III Sector Wind energy Facility Type Commercial Scale Wind...

  14. Mountain View Power Partners III Wind Farm | Open Energy Information

    Open Energy Info (EERE)

    III Wind Farm Jump to: navigation, search Name Mountain View Power Partners III Wind Farm Facility Mountain View Power Partners III Sector Wind energy Facility Type Commercial...

  15. PROJECT SELECTIONS FOR DOE PHASE III XLERATOR SMALL BUSINESS...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PROJECT SELECTIONS FOR DOE PHASE III XLERATOR SMALL BUSINESS PROGRAM PROJECT SELECTIONS FOR DOE PHASE III XLERATOR SMALL BUSINESS PROGRAM PDF icon SBIRPhaseIII.pdf More Documents...

  16. New Low Emittance Lattice for the Super-B Accelerator

    SciTech Connect (OSTI)

    Biagini, M.E.; Boscolo, M.; Raimondi, P.; Tomassini, S.; Zobov, M.; Seeman, J.; Sullivan, M.; Wienands, U.; Wittmer, W.; Bettoni, S.; Paoloni, E.; Bogomyagkov, A.; Koop, I.; Levichev, E.; Nikitin, S.; Piminov, P.; Shatilov, D.; /Novosibirsk, IYF

    2011-10-21

    New low emittance lattices have been designed for the asymmetric SuperB accelerator, aiming at a luminosity of 10{sup 36} cm{sup -2} s{sup -1}. Main optics features are two alternating arc cells with different horizontal phase advance, decreasing beam emittance and allowing at the same time for easy chromaticity correction in the arcs. Emittance can be further reduced by a factor of two for luminosity upgrade. Spin rotation schemes for the e{sup -} beam have been studied to provide longitudinal polarization at the IP, and implementation into the lattice is in progress.

  17. Marketing manufactured housing under the ''Super Good Cents'' Program

    SciTech Connect (OSTI)

    Mohler, B.L.; Smith, S.A.

    1986-01-01

    The objective of this study is to propose a strategy for including manufactured housing (MH) in Bonneville Power Administration's Super Good Cents (SGC) Program. This report presents information on the site-built SGC program, the characterization of MH consumers, the options for including MH in the SGC program, and the recommendations for including MHs in the SGC program. The purposed strategy for including MHs in the SGC program is designed to reduce risks to manufacturers and dealers, stimulate demand, and allow for maximum flexibility.

  18. Nitriding of super alloys for enhancing physical properties

    DOE Patents [OSTI]

    Purohit, Ankur

    1986-01-01

    The invention teaches the improvement of certain super alloys by exposing the alloy to an atmosphere of elemental nitrogen at elevated temperatures in excess of 750.degree. C. but less than 1150.degree. C. for an extended duration, viz., by nitriding the surface of the alloy, to establish barrier nitrides of the order of 25-100 micrometers thickness. These barrier nitrides appear to shield the available oxidizing metallic species of the alloy for up to a sixfold improved resistance against oxidation and also appear to impede egress of surface dislocations for increased fatigue and creep strengths.

  19. Control Surveys for Underground Construction of the Superconducting Super Collider

    SciTech Connect (OSTI)

    Greening, W.J.Trevor; Robinson, Gregory L.; Robbins, Jeffrey S.; Ruland, Robert E.; /SLAC

    2005-08-16

    Particular care had to be taken in the design and implementation of the geodetic control systems for the Superconducting Super Collider (SSC) due to stringent accuracy requirements, the demanding tunneling schedule, long duration and large size of the construction effort of the project. The surveying requirements and the design and implementation of the surface and underground control scheme for the precise location of facilities which include approximately 120 km of bored tunnel are discussed. The methodology used for the densification of the surface control networks, the technique used for the transfer of horizontal and vertical control into the underground facilities, and the control traverse scheme employed in the tunnels is described.

  20. The Next Generation Microlensing Search: SuperMacho

    SciTech Connect (OSTI)

    Drake, A; Cook, K; Hiriart, R; Keller, S; Miknaitis, G; Nilolaev, S; Olsen, K; Prochter, G; Rest, A; Schmidt, B; Smith, C; Stubbs, C; Suntzeff, N; Welch, D; Becker, A; Clocchiati, A; Covarrubias, R

    2003-10-27

    Past microlensing experiments such as the MACHO project have discovered the presence of a larger than expected number of microlensing events toward the Large Magellanic Cloud (LMC). These events could represent a large fraction of the dark matter in the halo of our Galaxy, if they are indeed due to halo lenses. However the locations of most of the lenses are poorly defined. The SuperMacho project will detect and follow up {approx}60 microlensing events exhibiting special properties due to binarity, etc., will allow us to better determine the location and nature of the lenses causing the LMC microlensing events.

  1. The Mark III vertex chamber

    SciTech Connect (OSTI)

    Adler, J.; Bolton, T.; Bunnell, K.; Cassell, R.; Cheu, E.; Freese, T.; Grab, C.; Mazaheri, G.; Mir, R.; Odian, A.

    1987-07-01

    The design and construction of the new Mark III vertex chamber is described. Initial tests with cosmic rays prove the ability of track reconstruction and yield triplet resolutions below 50 ..mu..m at 3 atm using argon/ethane (50:50). Also performed are studies using a prototype of a pressurized wire vertex chamber with 8 mm diameter straw geometry. Spatial resolution of 35mm was obtained using dimethyl ether (DME) at 1 atm and 30 ..mu..m using argon/ethane (50/50 mixture) at 4 atm. Preliminary studies indicate the DME to adversely affect such materials as aluminized Mylar and Delrin.

  2. III. Waiver of Proposed Rulemaking

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    82 Federal Register / Vol. 77, No. 241 / Friday, December 14, 2012 / Rules and Regulations technical errors in § 447.400(a) and § 447.405 listed on page 66701. One correction ensures consistency between two sentences in the same paragraph and the other restores text inadvertently omitted from the final rule that had been included in the May 11, 2012 notice of proposed rulemaking (77 FR 27671) on pages 26789-90. Thus, we are correcting page 66701 to reflect the correct information. III. Waiver

  3. Conditions for super-adiabatic droplet growth after entrainment mixing

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Yang, Fan; Shaw, Raymond; Xue, Huiwen

    2016-07-29

    Cloud droplet response to entrainment and mixing between a cloud and its environment is considered, accounting for subsequent droplet growth during adiabatic ascent following a mixing event. The vertical profile for liquid water mixing ratio after a mixing event is derived analytically, allowing the reduction to be predicted from the mixing fraction and from the temperature and humidity for both the cloud and environment. It is derived for the limit of homogeneous mixing. The expression leads to a critical height above the mixing level: at the critical height the cloud droplet radius is the same for both mixed and unmixedmore » parcels, and the critical height is independent of the updraft velocity and mixing fraction. Cloud droplets in a mixed parcel are larger than in an unmixed parcel above the critical height, which we refer to as the “super-adiabatic” growth region. Analytical results are confirmed with a bin microphysics cloud model. Using the model, we explore the effects of updraft velocity, aerosol source in the environmental air, and polydisperse cloud droplets. Results show that the mixed parcel is more likely to reach the super-adiabatic growth region when the environmental air is humid and clean. It is also confirmed that the analytical predictions are matched by the volume-mean cloud droplet radius for polydisperse size distributions. The findings have implications for the origin of large cloud droplets that may contribute to onset of collision–coalescence in warm clouds.« less

  4. One pass core design of a super fast reactor

    SciTech Connect (OSTI)

    Liu, Qingjie; Oka, Yoshiaki

    2013-07-01

    One pass core design for Supercritical-pressure light water-cooled fast reactor (Super FR) is proposed. The whole core is cooled with upward flow in one through flow pattern like PWR. Compared with the previous two pass core design; this new flow pattern can significantly simplify the core concept. Upper core structure, coolant flow scheme as well as refueling procedure are as simple as in PWR. In one pass core design, supercritical-pressure water is at approximately 25.0 MPa and enters the core at 280 C. degrees and is heated up in one through flow pattern upwardly to the average outlet temperature of 500 C. degrees. Great density change in vertical direction can cause significant axial power offset during the cycle. Meanwhile, Pu accumulated in the UO{sub 2} fuel blanket assemblies also introduces great power increase during cycle, which requires large amount of flow for heat removal and makes the outlet temperature of blanket low at the beginning of equilibrium cycle (BOEC). To deal with these issues, some MOX fuel is applied in the bottom region of the blanket assembly. This can help to mitigate the power change in blanket due to Pu accumulation and to increase the outlet temperature of the blanket during cycle. Neutron transport and thermohydraulics coupled calculation shows that this design can satisfy the requirement in the Super FR principle for both 500 C. degrees outlet temperature and negative coolant void reactivity. (authors)

  5. ON THE VIGOR OF MANTLE CONVECTION IN SUPER-EARTHS

    SciTech Connect (OSTI)

    Miyagoshi, Takehiro; Tachinami, Chihiro; Kameyama, Masanori; Ogawa, Masaki E-mail: ctchnm.geo@gmail.com E-mail: cmaogawa@mail.ecc.u-tokyo.ac.jp

    2014-01-01

    Numerical models are presented to clarify how adiabatic compression affects thermal convection in the mantle of super-Earths tentimes the Earth's mass. The viscosity strongly depends on temperature, and the Rayleigh number is much higher than that of the Earth's mantle. The strong effect of adiabatic compression reduces the activity of mantle convection; hot plumes ascending from the bottom of the mantle lose their thermal buoyancy in the middle of the mantle owing to adiabatic decompression, and do not reach the surface. A thick lithosphere, as thick as 0.1times the depth of the mantle, develops along the surface boundary, and the efficiency of convective heat transport measured by the Nusselt number is reduced by a factor of about four compared with the Nusselt number for thermal convection of incompressible fluid. The strong effect of adiabatic decompression is likely to inhibit hot spot volcanism on the surface and is also likely to affect the thermal history of the mantle, and hence, the generation of magnetic field in super-Earths.

  6. Low-background tracker development for SuperNEMO

    SciTech Connect (OSTI)

    Mott, James [University College London, London, WC1E 6BT (United Kingdom)] [University College London, London, WC1E 6BT (United Kingdom); Collaboration: SuperNEMO Collaboration; and others

    2013-08-08

    The SuperNEMO experiment will search for neutrinoless double beta decay (0???) with a target sensitivity of T{sub 1/2}(0?) > 10{sup 26} years, corresponding to an effective neutrino mass of 50-100 meV. At its heart there is a low-background gaseous tracking detector which allows for extremely efficient background rejection and, if 0??? is observed, may provide important insights into the mechanism via which it may be mediated. Radon inside the tracker, which can mimic rare ?? events, is one of the most dangerous backgrounds for SuperNEMO. To reach the target sensitivity the radon concentration inside the tracking volume must be < 0.15 mBq/m{sup 3}. To reach this challengingly-low level of radon, a considerable program of R and D has been undertaken. This includes automation of the tracker-wiring process, development of a dedicated setup to measure radon diffusion and a 'radon concentration line' which will be able to measure levels of radon in the ?Bq/m{sup 3} range.

  7. Testing and Characterization of SuperCDMS Dark Matter Detectors

    SciTech Connect (OSTI)

    Shank, Benjamin

    2014-05-01

    The Cryogenic Dark Matter Search (SuperCDMS) relies on collection of phonons and charge carriers in semiconductors held at tens of milliKelvin as handles for detection of Weakly Interacting Massive Particles (WIMPs). This thesis begins with a brief overview of the direct dark matter search (Chapter 1) and SuperCDMS detectors (Chapter 2). In Chapter 3, a 3He evaporative refrigerator facility is described. Results from experiments performed in-house at Stanford to measure carrier transport in high-purity germanium (HPGe) crystals operated at sub-Kelvin temperatures are presented in Chapter 4. Finally, in Chapter 5 a new numerical model and a time-domain optimal filtering technique are presented, both developed for use with superconducting Transition Edge Sensors (TESs), that provide excellent event reconstruction for single particle interactions in detectors read out with superconducting W-TESs coupled to energy-collecting films of Al. This thesis is not intended to be read straight through. For those new to CDMS or dark matter searches, the first two chapters are meant to be a gentle introduction for experimentalists. They are by no means exhaustive. The remaining chapters each stand alone, with different audiences.

  8. Implementing mitigative actions on the Superconducting Super Collider project

    SciTech Connect (OSTI)

    Sands, T.L. )

    1993-01-01

    The Super Collider is the first project for which a Mitigation Action Plan (MAP) was prepared under a DOE Order that became effective in 1990. The policy requires a MAP for any project where environmental findings were predicated on taking mitigative actions. The MAP must be approved prior to the start of preliminary design and thus cannot be site or facility-specific because the requisite level of detail would not be available. This gap is filled by a series of environmental compliance plans (ECP) that are prepared by the architect-engineer/constructions manager under the direction of the DOE Management and Operations Contractor for the Super Collider. A given ECP identifies the environmental protection measures applicable to the respective contract package. The designated design team uses the ECP as one of its requirements documents and the environmental staff uses it during design reviews to verify compliance with the MAP. Site audits and monitoring data are used to document compliance and verify the effectiveness of mitigative actions, or identify required corrective actions. The applicability of this process to other projects falling within the scope of the National Environmental Policy Act is discussed.

  9. Denver SuperShuttle CNG Fleet Evaluation; Evaluacion de la flotilla de GNC de la empresa SuperShuttle de Denver

    SciTech Connect (OSTI)

    LaRocque, T.

    2001-10-01

    A description of a joint effort between Denver SuperShuttle, the Gas Research Institute (GRI) and DOE that evaluated two types of bi-fuel and compressed natural gas.

  10. SuperShuttle CNG Fleet Study Summary; Resumen de Estuidio de la Flotilla de GNC de la Empresa SuperShuttle

    SciTech Connect (OSTI)

    Eudy, L.

    2001-10-01

    An account of the successful use of alternative fuels in a fleet of SuperShuttle passenger vans, which offer shared-rides between Boulder and Denver International Airport.

  11. DOE/NNSA perspective safeguard by design: GEN III/III+ light water reactors and beyond

    SciTech Connect (OSTI)

    Pan, Paul Y

    2010-12-10

    An overview of key issues relevant to safeguards by design (SBD) for GEN III/IV nuclear reactors is provided. Lessons learned from construction of typical GEN III+ water reactors with respect to SBD are highlighted. Details of SBD for safeguards guidance development for GEN III/III+ light water reactors are developed and reported. This paper also identifies technical challenges to extend SBD including proliferation resistance methodologies to other GEN III/III+ reactors (except HWRs) and GEN IV reactors because of their immaturity in designs.

  12. GRED III Phase II | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    III Phase II GRED III Phase II Engineered Geothermal Systems, Low Temp, Exploration Demonstration Projects. Project objectives: To gain a better understanding of the geothermal reservoir at Chena Hot Springs Resort in Alaska; Test and document the reliability of previous predictions as to the nature of the reservoir. egs_karl_gred_3_phase_2.pdf (601.26 KB) More Documents & Publications Fairbanks Geothermal Energy Project GRED Drilling Award … GRED III Phase II; 2010 Geothermal Technology

  13. Kotzebue Wind Project III | Open Energy Information

    Open Energy Info (EERE)

    Kotzebue Wind Project III Facility Kotzebue Wind Project Sector Wind energy Facility Type Small Scale Wind Facility Status In Service Owner Kotzebue Elec. Assoc. Developer Kotzebue...

  14. Low Emittance Tuning Studies for SuperB

    SciTech Connect (OSTI)

    Liuzzo, Simone; Biagini, Maria; Raimondi, Pantaleo; Donald, Martin; /SLAC

    2012-07-06

    SuperB[1] is an international project for an asymmetric 2 rings collider at the B mesons cm energy to be built in the Rome area in Italy. The two rings will have very small beam sizes at the Interaction Point and very small emittances, similar to the Linear Collider Damping Rings ones. In particular, the ultra low vertical emittances, 7 pm in the LER and 4 pm in the HER, need a careful study of the misalignment errors effects on the machine performances. Studies on the closed orbit, vertical dispersion and coupling corrections have been carried out in order to specify the maximum allowed errors and to provide a procedure for emittance tuning. A new tool which combines MADX and Matlab routines has been developed, allowing for both corrections and tuning. Results of these studies are presented.

  15. Longitudinal Bunch Position Control for the Super-B Accelerator

    SciTech Connect (OSTI)

    Bertsche, Kirk; Rivetta, Claudio; Sullivam, Michael K.; Drago, Alessandro; /Frascati

    2009-05-15

    The use of normal conducting cavities and an ion-clearing gap will cause a significant RF accelerating voltage gap transient and longitudinal phase shift of the individual bunches along the bunch train in both rings of the SuperB accelerator. Small relative centroid position shifts between bunches of the colliding beams will have a large adverse impact on the luminosity due to the small {beta}*{sub y} at the interaction point (IP). We investigate the possibility of minimizing the relative longitudinal position shift between bunches by reducing the gap transient in each ring and matching the longitudinal bunch positions of the two rings at the IP using feedback/feedforward techniques in the LLRF. The analysis is conducted assuming maximum use of the klystron power installed in the system.

  16. An Improved Design for a Super-B Interaction Region

    SciTech Connect (OSTI)

    Sullivan, M.K.; Seeman, J.; Wienands, U.; Bettoni, S.; Biagini, M.E.; Raimondi, P.; Paoloni, E.; /INFN, Pisa

    2008-07-25

    We present an improved design for a Super-B interaction region. The new design attempts to minimize the bending of the two colliding beams which results from shared magnetic elements near the Interaction Point (IP). The total crossing angle at the IP is increased from 34 mrad to 50 mrad and the distance from the IP to the first quadrupole is increased. Although the two beams still travel through this shared magnet, these changes allow for a new magnetic field design with a septum which gives the magnet two magnetic centers. This greatly reduces the beam bending from this shared quadrupole and thereby reduces the radiative bhabha background for the detector as well as any beam emittance growth from the bending. We describe the new design for the interaction region.

  17. SEARCH FOR NEW PHYSICS AT A SUPER-B FACTORY.

    SciTech Connect (OSTI)

    BROWDER,T.E.; SONI,A.

    2004-01-05

    The importance of a Super-B Factory in the search for New Physics, in particular, due to CP-od phase(s) from physics beyond the Standard Model is surveyed. The first point to emphasize is that we know now how to directly measure all three angles of the unitarity triangle very cleanly, i. e. without theoretical assumptions with irreducible theory error {le} 1%; however this requires much more luminosity than is currently available at B-factories. Direct searches via penguin-dominated hadronic modes as well as radiative, pair-leptonic and semi-leptonic decays are also discussed. Null tests of the SM are stressed as these will play a crucial role especially if the effects of BSM phase(s) on B-physics are small.

  18. Super Efficient Refrigerator Program (SERP) evaluation. Volume 1: Process evaluation

    SciTech Connect (OSTI)

    Sandahl, L.J.; Ledbetter, M.R.; Chin, R.I.; Lewis, K.S.; Norling, J.M.

    1996-01-01

    The Pacific Northwest National Laboratory (PNNL) conducted this study for the US Department of Energy (DOE) as part of the Super Efficient Refrigerator Program (SERP) Evaluation. This report documents the SERP formation and implementation process, and identifies preliminary program administration and implementation issues. The findings are based primarily on interviews with those familiar with the program, such as utilities, appliance manufacturers, and SERP administrators. These interviews occurred primarily between March and April 1995, when SERP was in the early stages of program implementation. A forthcoming report will estimate the preliminary impacts of SERP within the industry and marketplace. Both studies were funded by DOE at the request of SERP Inc., which sought a third-party evaluation of its program.

  19. Super-Joule heating in graphene and silver nanowire network

    SciTech Connect (OSTI)

    Maize, Kerry; Das, Suprem R.; Sadeque, Sajia; Mohammed, Amr M. S.; Shakouri, Ali E-mail: alam@purdue.edu; Janes, David B.; Alam, Muhammad A. E-mail: alam@purdue.edu

    2015-04-06

    Transistors, sensors, and transparent conductors based on randomly assembled nanowire networks rely on multi-component percolation for unique and distinctive applications in flexible electronics, biochemical sensing, and solar cells. While conduction models for 1-D and 1-D/2-D networks have been developed, typically assuming linear electronic transport and self-heating, the model has not been validated by direct high-resolution characterization of coupled electronic pathways and thermal response. In this letter, we show the occurrence of nonlinear super-Joule self-heating at the transport bottlenecks in networks of silver nanowires and silver nanowire/single layer graphene hybrid using high resolution thermoreflectance (TR) imaging. TR images at the microscopic self-heating hotspots within nanowire network and nanowire/graphene hybrid network devices with submicron spatial resolution are used to infer electrical current pathways. The results encourage a fundamental reevaluation of transport models for network-based percolating conductors.

  20. Analytical SuperSTEM for extraterrestrial materials research

    SciTech Connect (OSTI)

    Bradley, J P; Dai, Z R

    2009-09-08

    Electron-beam studies of extraterrestrial materials with significantly improved spatial resolution, energy resolution and sensitivity are enabled using a 300 keV SuperSTEM scanning transmission electron microscope with a monochromator and two spherical aberration correctors. The improved technical capabilities enable analyses previously not possible. Mineral structures can be directly imaged and analyzed with single-atomic-column resolution, liquids and implanted gases can be detected, and UV-VIS optical properties can be measured. Detection limits for minor/trace elements in thin (<100 nm thick) specimens are improved such that quantitative measurements of some extend to the sub-500 ppm level. Electron energy-loss spectroscopy (EELS) can be carried out with 0.10-0.20 eV energy resolution and atomic-scale spatial resolution such that variations in oxidation state from one atomic column to another can be detected. Petrographic mapping is extended down to the atomic scale using energy-dispersive x-ray spectroscopy (EDS) and energy-filtered transmission electron microscopy (EFTEM) imaging. Technical capabilities and examples of the applications of SuperSTEM to extraterrestrial materials are presented, including the UV spectral properties and organic carbon K-edge fine structure of carbonaceous matter in interplanetary dust particles (IDPs), x-ray elemental maps showing the nanometer-scale distribution of carbon within GEMS (glass with embedded metal and sulfides), the first detection and quantification of trace Ti in GEMS using EDS, and detection of molecular H{sub 2}O in vesicles and implanted H{sub 2} and He in irradiated mineral and glass grains.

  1. Characterization of microstructure and texture across dissimilar super duplex/austenitic stainless steel weldment joint by super duplex filler metal

    SciTech Connect (OSTI)

    Eghlimi, Abbas; Shamanian, Morteza; Eskandarian, Masoomeh; Zabolian, Azam; Szpunar, Jerzy A.

    2015-08-15

    In the present paper, microstructural changes across an as-welded dissimilar austenitic/duplex stainless steel couple welded by a super duplex stainless steel filler metal using gas tungsten arc welding process is characterized with optical microscopy and electron back-scattered diffraction techniques. Accordingly, variations of microstructure, texture, and grain boundary character distribution of base metals, heat affected zones, and weld metal were investigated. The results showed that the weld metal, which was composed of Widmanstätten austenite side-plates and allotriomorphic grain boundary austenite morphologies, had the weakest texture and was dominated by low angle boundaries. The welding process increased the ferrite content but decreased the texture intensity at the heat affected zone of the super duplex stainless steel base metal. In addition, through partial ferritization, it changed the morphology of elongated grains of the rolled microstructure to twinned partially transformed austenite plateaus scattered between ferrite textured colonies. However, the texture of the austenitic stainless steel heat affected zone was strengthened via encouraging recrystallization and formation of annealing twins. At both interfaces, an increase in the special character coincident site lattice boundaries of the primary phase as well as a strong texture with <100> orientation, mainly of Goss component, was observed. - Graphical abstract: Display Omitted - Highlights: • Weld metal showed local orientation at microscale but random texture at macroscale. • Intensification of <100> orientated grains was observed adjacent to the fusion lines. • The austenite texture was weaker than that of the ferrite in all duplex regions. • Welding caused twinned partially transformed austenites to form at SDSS HAZ. • At both interfaces, the ratio of special CSL boundaries of the primary phase increased.

  2. Preparation of III-V semiconductor nanocrystals

    DOE Patents [OSTI]

    Alivisatos, A.P.; Olshavsky, M.A.

    1996-04-09

    Nanometer-scale crystals of III-V semiconductors are disclosed. They are prepared by reacting a group III metal source with a group V anion source in a liquid phase at elevated temperature in the presence of a crystallite growth terminator such as pyridine or quinoline. 4 figs.

  3. Preparation of III-V semiconductor nanocrystals

    DOE Patents [OSTI]

    Alivisatos, A. Paul; Olshavsky, Michael A.

    1996-01-01

    Nanometer-scale crystals of III-V semiconductors are disclosed, They are prepared by reacting a group III metal source with a group V anion source in a liquid phase at elevated temperature in the presence of a crystallite growth terminator such as pyridine or quinoline.

  4. SuperTruck … Development and Demonstration of a Fuel-Efficient Class 8

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Tractor & Trailer | Department of Energy SuperTruck … Development and Demonstration of a Fuel-Efficient Class 8 Tractor & Trailer SuperTruck … Development and Demonstration of a Fuel-Efficient Class 8 Tractor & Trailer 2012 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting vss064_jadin_2012_o.pdf (2.16 MB) More Documents & Publications SuperTruck … Development and Demonstration of a Fuel-Efficient Class 8

  5. Non-uniform Aging on Super Duty Diesel Truck Aged Urea Cu/Zeolite SCR

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Catalysts | Department of Energy uniform Aging on Super Duty Diesel Truck Aged Urea Cu/Zeolite SCR Catalysts Non-uniform Aging on Super Duty Diesel Truck Aged Urea Cu/Zeolite SCR Catalysts Cu/Zeolite SCR catalysts aged for 50k miles on a Super Duty diesel truck deer10_cheng.pdf (950.84 KB) More Documents & Publications Deactivation Mechanisms of Base Metal/Zeolite Urea Selective Catalytic Reduction Materials, and Development of Zeolite-Based Hydrocarbon Adsorber Materials Deactivation

  6. EERE Success Story-SuperTruck Initiative Partner Improves Class 8 Truck

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency by 115% | Department of Energy SuperTruck Initiative Partner Improves Class 8 Truck Efficiency by 115% EERE Success Story-SuperTruck Initiative Partner Improves Class 8 Truck Efficiency by 115% June 23, 2015 - 3:21pm Addthis EERE Success Story—SuperTruck Initiative Partner Improves Class 8 Truck Efficiency by 115% With help from the Energy Department, Class 8 trucks recently hit a record of 12 miles per gallon (mpg) freight efficiency. This milestone is actually a 115%

  7. SuperTruck … Development and Demonstration of a Fuel-Efficient Class 8

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Tractor & Trailer | Department of Energy 3 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting vss064_oehlerking_2013_o.pdf (2.41 MB) More Documents & Publications SuperTruck … Development and Demonstration of a Fuel-Efficient Class 8 Tractor & Trailer SuperTruck … Development and Demonstration of a Fuel-Efficient Class 8 Tractor & Trailer Vehicle Technologies Office Merit Review 2015: SuperTruck - Development

  8. Vids4Grids: Smart Meters and Super Cables | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Vids4Grids: Smart Meters and Super Cables Vids4Grids: Smart Meters and Super Cables March 14, 2011 - 4:46pm Addthis This episode of Vids 4 Grids will take us to Itron's smart meter factory in West Union, SC where we will learn the role smart meters play in the Smart Grid. Deborah J. Buterbaugh Energy Project Specialist at National Energy Technology Laboratory What does this mean for me? Smart meters allow consumers to get real time information about their energy usage. Super cables help provide

  9. L Prize(tm): The Race for Super Efficient Light Bulbs | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    L Prize(tm): The Race for Super Efficient Light Bulbs L Prize(tm): The Race for Super Efficient Light Bulbs This September 23, 2008 webcast provided an overview of the Bright Tomorrow Lighting Prize (L Prize) technology competition. The L Prize calls for super-efficient SSL products to replace two of the most common light bulbs used today: the 60-watt incandescent and the PAR-38 halogen reflector. Kelly Gordon, Pacific Northwest National Laboratory, kicked off the webcast with an overview of the

  10. PROJECT SELECTIONS FOR DOE PHASE III XLERATOR SMALL BUSINESS PROGRAM |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy PROJECT SELECTIONS FOR DOE PHASE III XLERATOR SMALL BUSINESS PROGRAM PROJECT SELECTIONS FOR DOE PHASE III XLERATOR SMALL BUSINESS PROGRAM SBIR_Phase_III.pdf (228.04 KB) More Documents & Publications SBIR_Phase_III.pdf PROJECT SELECTIONS FOR DOE PHASE III XLERATOR SMALL BUSINESS PROGRAM - pg 3 Albany HTS Power Cable

  11. Vehicle Technologies Office Merit Review 2014: SuperTruck Program: Engine Project Review

    Broader source: Energy.gov [DOE]

    Presentation given by Detroit Diesel Corporation at 2014 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about SuperTruck Program...

  12. Vehicle Technologies Office Merit Review 2014: Volvo SuperTruck- Powertrain Technologies for Efficiency Improvement

    Broader source: Energy.gov [DOE]

    Presentation given by Volvo at 2014 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about Volvo SuperTruck powertrain...

  13. Princeton and PPPL projects selected to run on super-powerful...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Princeton and PPPL projects selected to run on super-powerful computer to be delivered to Oak Ridge Leadership Computing Facility By John Greenwald June 1, 2015 Tweet Widget Google...

  14. Vehicle Technologies Office Merit Review 2015: SuperTruck Program: Engine Project Review

    Broader source: Energy.gov [DOE]

    Presentation given by Detroit Diesel at 2015 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about SuperTruck program: engine...

  15. Super-Poissonian Statistics of Photon Emission from Single CdSe...

    Office of Scientific and Technical Information (OSTI)

    Title: Super-Poissonian Statistics of Photon Emission from Single CdSe-CdS Core-Shell Nanocrystals Coupled to Metal Nanostructures Authors: Park, Young-Shin ; Ghosh, Yagnaseni ; ...

  16. A New Interaction Region Design for the Super-B Factory

    SciTech Connect (OSTI)

    Sullivan, Michael; Bertsche, Kirk; Bettoni, Simona; Paoloni, Eugenio; Raimondi, Pantaleo; Vobly, Pavel; /Novosibirsk, IYF

    2012-07-06

    A final focus magnet design that uses super-ferric magnets is introduced for the SuperB interaction region. The baseline design has air-core super-conducting quadrupoles. This idea instead uses super-conducting wire in an iron yoke. The iron is in the shape of a Panofsky quadrupole and this allows two quadrupoles to be side-by-side with no intervening iron as long as the gradients of the two quads are equal. This feature allows us to move in as close as possible to the collision point and minimize the beta functions in the interaction region. The superferric design has advantages as well as drawbacks and we will discuss these in the paper.

  17. Evaluation of a 1000 MW Commercial Ultra Super-Critical Coal Boiler |

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Argonne Leadership Computing Facility prediction of instantaneous O2 mass fraction in a hypothetical commercial scale 1000 MW, Ultra Super-Critical (USC) coal boiler Large eddy simulation prediction of instantaneous O2 mass fraction in a hypothetical commercial scale 1000 MW, Ultra Super-Critical (USC) coal boiler. Simulation results may suggest new design features that can have an impact on the operation of current and next-generation USC boilers. Carbon Capture Multi-Disciplinary

  18. Vehicle Technologies Office Issues Notice of Intent for SuperTruck II

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Funding Opportunity Announcement | Department of Energy SuperTruck II Funding Opportunity Announcement Vehicle Technologies Office Issues Notice of Intent for SuperTruck II Funding Opportunity Announcement February 10, 2016 - 10:40am Addthis The Vehicle Technologies Office (VTO) has issued a Notice of Intent (No. DE-FOA-0001447) to make interested parties aware of its plan to issue a Funding Opportunity Announcement entitled "Advanced Systems Level Technology Development, Integration

  19. Vehicle Technologies Office Merit Review 2014: Cummins SuperTruck Program

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technology and System Level Demonstration of Highly Efficient and Clean, Diesel Powered Class 8 Trucks | Department of Energy Cummins SuperTruck Program Technology and System Level Demonstration of Highly Efficient and Clean, Diesel Powered Class 8 Trucks Vehicle Technologies Office Merit Review 2014: Cummins SuperTruck Program Technology and System Level Demonstration of Highly Efficient and Clean, Diesel Powered Class 8 Trucks Presentation given by Cummins Inc. at 2014 DOE Hydrogen and

  20. Development and Demonstration of a Fuel-Efficient HD Engine (DOE SuperTruck

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Program) | Department of Energy Engine (DOE SuperTruck Program) Development and Demonstration of a Fuel-Efficient HD Engine (DOE SuperTruck Program) Discusses engine efficiency contributions of enhanced fuel injection rematched to new piston geometry, improved charge air system, revised base engine components reduce friction and turbocompounding. deer11_deojeda.pdf (2.06 MB) More Documents & Publications Development and Demonstration of a Fuel-Efficient HD Engine

  1. Catalyst Cartography: 3D Super-Resolution Mapping of Catalytic Activity |

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The Ames Laboratory Catalyst Cartography: 3D Super-Resolution Mapping of Catalytic Activity Thanks to a groundbreaking new method, scientists have created the first 3D super-resolution maps of catalytic activity on an individual catalytic nanoparticle while reactions are occurring. Catalysts are used in manufacturing everything from stain remover to rocket fuel; they make production more efficient by facilitating chemical reactions. Each catalyst being studied is only about 200 nanometers in

  2. High-pressure science gets super-sized | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    High-pressure science gets super-sized By Tona Kunz * October 23, 2012 Tweet EmailPrint ARGONNE, Ill. - The study of materials at extreme conditions took a giant leap forward with the discovery of a way to generate super high pressures without using shock waves whose accompanying heat turns solids to liquid. This discovery will allow scientists for the first time to reach static pressure levels exceeding four million atmospheres, a high-pressure environment where new unique compounds could be

  3. Synchrotron X-ray Studies of Super-critical Carbon Dioxide / Reservoir Rock

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Interfaces | Department of Energy Synchrotron X-ray Studies of Super-critical Carbon Dioxide / Reservoir Rock Interfaces Synchrotron X-ray Studies of Super-critical Carbon Dioxide / Reservoir Rock Interfaces Project obectives: Utilize synchrotron X-ray measurements, to monitor all aspects of atomic to nanoscale structural changes resulting from chemical interactions of scCO2-H2O binary fluids with rocks under environments directly relevant to EGS. chemistry_you_synchrotron_studies.pdf (1.84

  4. Vehicle Technologies Office Merit Review 2015: Cummins SuperTruck Program

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technology and System Level Demonstration of Highly Efficient and Clean, Diesel Powered Class 8 Trucks | Department of Energy Cummins SuperTruck Program Technology and System Level Demonstration of Highly Efficient and Clean, Diesel Powered Class 8 Trucks Vehicle Technologies Office Merit Review 2015: Cummins SuperTruck Program Technology and System Level Demonstration of Highly Efficient and Clean, Diesel Powered Class 8 Trucks Presentation given by Cummins at 2015 DOE Hydrogen and Fuel

  5. Multi-pulse operation of a super-radiant backward-wave oscillator

    SciTech Connect (OSTI)

    Bandurkin, I. V.; Savilov, A. V.

    2014-08-15

    Theory of a backward-wave electron oscillator operating in the non-stationary regime of super-radiation of short powerful rf pulses is developed. It is shown that there exist multi-frequency regimes of generation of either two-peak or three-peak output signal with different characteristic frequencies in every peak. The use of such regimes allows increasing the duration, the peak power, and the total energy of the output super-radiation rf pulse.

  6. Solid-immersion fluorescence microscopy with increased emission and super resolution

    SciTech Connect (OSTI)

    Liau, Z. L.; Porter, J. M.; Liau, A. A.; Chen, J. J.; Salmon, W. C.; Sheu, S. S.

    2015-01-07

    We investigate solid-immersion fluorescence microscopy suitable for super-resolution nanotechnology and biological imaging, and have observed limit of resolution as small as 15?nm with microspheres, mitochondria, and chromatin fibers. We have further observed that fluorescence efficiency increases with excitation power density, implicating appreciable stimulated emission and increased resolution. We discuss potential advantages of the solid-immersion microscopy, including combined use with previously established super-resolution techniques for reaching deeper beyond the conventional diffraction limit.

  7. Photodetectors using III-V nitrides

    DOE Patents [OSTI]

    Moustakas, T.D.; Misra, M.

    1997-10-14

    A photodetector using a III-V nitride and having predetermined electrical properties is disclosed. The photodetector includes a substrate with interdigitated electrodes formed on its surface. The substrate has a sapphire base layer, a buffer layer formed from a III-V nitride and a single crystal III-V nitride film. The three layers are formed by electron cyclotron resonance microwave plasma-assisted molecular beam epitaxy (ECR-assisted MBE). Use of the ECR-assisted MBE process allows control and predetermination of the electrical properties of the photodetector. 24 figs.

  8. Photodetectors using III-V nitrides

    DOE Patents [OSTI]

    Moustakas, Theodore D.; Misra, Mira

    1997-01-01

    A photodetector using a III-V nitride and having predetermined electrical properties is disclosed. The photodetector includes a substrate with interdigitated electrodes formed on its surface. The substrate has a sapphire base layer, a buffer layer formed from a III-V nitride and a single crystal III-V nitride film. The three layers are formed by electron cyclotron resonance microwave plasma-assisted molecular beam epitaxy (ECR-assisted MBE). Use of the ECR-assisted MBE process allows control and predetermination of the electrical properties of the photodetector.

  9. Terrestrial planet formation in the presence of migrating super-Earths

    SciTech Connect (OSTI)

    Izidoro, Andr; Morbidelli, Alessandro; Raymond, Sean N. E-mail: morbidelli@oca.eu

    2014-10-10

    Super-Earths with orbital periods less than 100 days are extremely abundant around Sun-like stars. It is unlikely that these planets formed at their current locations. Rather, they likely formed at large distances from the star and subsequently migrated inward. Here we use N-body simulations to study the effect of super-Earths on the accretion of rocky planets. In our simulations, one or more super-Earths migrate inward through a disk of planetary embryos and planetesimals embedded in a gaseous disk. We tested a wide range of migration speeds and configurations. Fast-migrating super-Earths (?{sub mig} ? 0.01-0.1 Myr) only have a modest effect on the protoplanetary embryos and planetesimals. Sufficient material survives to form rocky, Earth-like planets on orbits exterior to the super-Earths'. In contrast, slowly migrating super-Earths shepherd rocky material interior to their orbits and strongly deplete the terrestrial planet-forming zone. In this situation any Earth-sized planets in the habitable zone are extremely volatile-rich and are therefore probably not Earth-like.

  10. Status of the Super-B factory Design

    SciTech Connect (OSTI)

    Wittmer, W.; Bertsche, K.; Chao, A.; Novokhatski, A.; Nosochkov, Y.; Seeman, J.; Sullivan, M.K.; Wienands, U.; Weathersby, S.; Bogomyagkov, A.V.; Levichev, E.; Nikitin, S.; Piminov, P.; Shatilov, D.; Sinyatkin, S.; Vobly, P.; Okunev, I.N.; Bolzon, B.; Brunetti, L.; Jeremie, A.; Biagini, M.E.; /Frascati /INFN, Pisa /Pisa U. /INFN, Genoa /Genoa U. /CERN /Orsay, LAL /LPSC, Grenoble /Saclay

    2012-05-18

    The SuperB international team continues to optimize the design of an electron-positron collider, which will allow the enhanced study of the origins of flavor physics. The project combines the best features of a linear collider (high single-collision luminosity) and a storage-ring collider (high repetition rate), bringing together all accelerator physics aspects to make a very high luminosity of 10{sup 36} cm{sup -2} sec{sup -1}. This asymmetric-energy collider with a polarized electron beam will produce hundreds of millions of B-mesons at the Y(4S) resonance. The present design is based on extremely low emittance beams colliding at a large Piwinski angle to allow very low {beta}{sub y} without the need for ultra short bunches. Use of crab-waist sextupoles will enhance the luminosity, suppressing dangerous resonances and allowing for a higher beam-beam parameter. The project has flexible beam parameters, improved dynamic aperture, and spin-rotators in the Low Energy Ring for longitudinal polarization of the electron beam at the Interaction Point. Optimized for best colliding-beam performance, the facility may also provide high-brightness photon beams for synchrotron radiation applications.

  11. A super-cusp divertor configuration for tokamaks

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Ryutov, D. D.

    2015-08-26

    Our study demonstrates a remarkable flexibility of advanced divertor configurations created with the remote poloidal field coils. The emphasis here is on the configurations with three poloidal field nulls in the divertor area. We are seeking the structures where all three nulls lie on the same separatrix, thereby creating two zones of a very strong flux expansion, as envisaged in the concept of Takase’s cusp divertor. It turns out that the set of remote coils can produce a cusp divertor, with additional advantages of: (i) a large stand-off distance between the divertor and the coils and (ii) a thorough controlmore » that these coils exert over the fine features of the configuration. In reference to these additional favourable properties acquired by the cusp divertor, the resulting configuration could be called ‘a super-cusp’. General geometrical features of the three-null configurations produced by remote coils are described. Furthermore, issues on the way to practical applications include the need for a more sophisticated control system and possible constraints related to excessively high currents in the divertor coils.« less

  12. SuperShuttle CNG Fleet Evaluation--Final Report

    SciTech Connect (OSTI)

    Eudy, L.

    2000-12-07

    The mission of the US Department of Energy's Office of Transportation Technologies is to promote the development and deployment of transportation technologies that reduce US dependence on foreign oil, while helping to improve the nation's air quality and promoting US competitiveness. In support of this mission, DOE has directed the National Renewable Energy Laboratory to conduct projects to evaluate the performance and acceptability of alternative fuel vehicles. NREL has undertaken several fleet study projects, which seek to provide objective real-world fleet experiences with AFVs. For this type of study we collect, analyze, and report on operational, cost, emissions, and performance data from AFVs being driven in a fleet application. The primary purpose of such studies is to make real-world information on AFVs available to fleet managers and other potential AFV purchasers. For this project, data was collected from 13 passenger vans operating in the Boulder/Denver, Colorado area. The study vehicles were all 1999 Ford E-350 passenger vans based at SuperShuttle's Boulder location. Five of the vans were dedicated CNG, five were bi-fuel CNG/gasoline, and three were standard gasoline vans that were used for comparison.

  13. The versatile link, a common project for super-LHC

    SciTech Connect (OSTI)

    Amaral, Luis; Dris, Stefanos; Gerardin, Alexandre; Huffman, Todd; Issever, Cigdem; Pacheco, Alberto Jimenez; Jones, Mark; Kwan, Simon; Lee, Shih-Chang; Lian, Zhijun; Liu, Tiankuan; /CERN /Oxford U. /Fermilab /Taipei, Computing Ctr. /Southern Methodist U.

    2009-07-01

    Radiation tolerant, high speed optoelectronic data transmission links are fundamental building blocks in today's large scale High Energy Physics (HEP) detectors, as exemplified by the four experiments currently under commissioning at the Large Hadron Collider (LHC), see for example. New experiments or upgrades will impose even more stringent demands on these systems from the point of view of performance and radiation tolerance. This can already be seen from the developments underway for the Super Large Hadron Collider (SLHC) project, a proposed upgrade to the LHC aiming at increasing the luminosity of the machine by factor of 10 to 10{sup 35} cm{sup -2}s{sup -1}, and thus providing a better chance to see rare processes and improving statistically marginal measurements. In the past, specific data transmission links have been independently developed by each LHC experiment for data acquisition (DAQ), detector control as well as trigger and timing distribution (TTC). This was justified by the different types of applications being targeted as well as by technological limitations preventing one single solution from fitting all requirements. However with today's maturity of optoelectronic and CMOS technologies it is possible to envisage the development of a general purpose optical link which can cover most transmission applications: a Versatile Link. Such an approach has the clear advantage of concentrating the development effort on one single project targeting an optical link whose final functionality will only result from the topology and configuration settings adopted.

  14. DETECTION OF THERMAL EMISSION FROM A SUPER-EARTH

    SciTech Connect (OSTI)

    Demory, Brice-Olivier; Seager, Sara; Benneke, Bjoern; Gillon, Michaeel; Deming, Drake; Jackson, Brian

    2012-06-01

    We report on the detection of infrared light from the super-Earth 55 Cnc e, based on four occultations obtained with Warm Spitzer at 4.5 {mu}m. Our data analysis consists of a two-part process. In a first step, we perform individual analyses of each data set and compare several baseline models to optimally account for the systematics affecting each light curve. We apply independent photometric correction techniques, including polynomial detrending and pixel mapping, that yield consistent results at the 1{sigma} level. In a second step, we perform a global Markov Chain Monte Carlo analysis, including all four data sets that yield an occultation depth of 131 {+-} 28 ppm, translating to a brightness temperature of 2360 {+-} 300 K in the IRAC 4.5 {mu}m channel. This occultation depth suggests a low Bond albedo coupled to an inefficient heat transport from the planetary day side to the night side, or else possibly that the 4.5 {mu}m observations probe atmospheric layers that are hotter than the maximum equilibrium temperature (i.e., a thermal inversion layer or a deep hot layer). The measured occultation phase and duration are consistent with a circular orbit and improves the 3{sigma} upper limit on 55 Cnc e's orbital eccentricity from 0.25 to 0.06.

  15. Development of Erbia-bearing Super High Burnup Fuel

    SciTech Connect (OSTI)

    Akio, Yamamoto; Toshikazu, Takeda; Hironobu, Unesaki; Masaaki, Mori; Masatoshi Yamasaki

    2006-07-01

    In this paper, concept and development plan of the Erbia (Er{sub 2}O{sub 3})-bearing super high burnup (Er-SHB) fuel for LWRs are described. In order to reduce the number of spent fuel assemblies, utilization of high burnup fuels with higher uranium enrichment is effective. However, the upper limitation of enrichment for LWR fuels is 5 wt% and current advanced fuel assemblies for LWRs are already reaching this limit. Though various efforts to overcome the 5 wt% enrichment limit have been undergoing, it will require considerable cost that may offset the economic benefit of high burnup fuels. We are proposing another pathway. By adding low content ({>=}0.2 wt%) of Erbia in all UO{sub 2} powder, reactivity of high enrichment (>5 wt%) fuel is suppressed under that of current fuel assemblies, i.e. we leverage the negative reactivity credit of Erbia. Since Erbia is mixed into UO{sub 2} powder just after the re-conversion, we can avoid most of the criticality safety issues appearing in the front-end stream. Namely, major improvements and re-licensing for equipments in transportation, storage and fabrication process will not be necessary. Therefore, the Er-SHB fuel will significantly contribute to reduction of fuel cycle cost. (authors)

  16. The first tunnel section of the Superconducting Super Collider project

    SciTech Connect (OSTI)

    Lundin, T.K.; Laughton, C.; Nelson, P.P.

    1990-11-01

    The Superconducting Super Collider (SSC) project will be constructed for the United States Department of Energy at a competitively-selected site in Ellis County, Texas, about 30 mile (50 km) south of the central business district of Dallas. The injector system and main collider ring will be housed in 70 mile (110 km) of tunnel, and the project will include additional shafts and underground enclosures with clear spans up to 30 ft (10 m) at depths of more than 250 ft (75 m). The first tunnel segment to be designed and constructed will include approximately 5.9 mile (9.4 km) of 12 ft (3.7 m) finished internal diameter tunnel, four shafts up to 55 ft (16.8 m) diameter, and various connecting tunnels and adits. Construction will be in weak rock lithologies, including mudstones, marls, and chalks with compressive strengths typically between 300 and 2500 psi (2.0 and 17.2 MPa). Design is underway, with an expected bid date before the end of 1990, and with start of construction following in the spring of 1991. 7 refs., 8 figs., 1 tab.

  17. COLLISIONAL STRIPPING AND DISRUPTION OF SUPER-EARTHS

    SciTech Connect (OSTI)

    Marcus, Robert A.; Sasselov, Dimitar; Hernquist, Lars; Stewart, Sarah T.

    2009-08-01

    The final stage of planet formation is dominated by collisions between planetary embryos. The dynamics of this stage determine the orbital configuration and the mass and composition of planets in the system. In the solar system, late giant impacts have been proposed for Mercury, Earth, Mars, and Pluto. In the case of Mercury, this giant impact may have significantly altered the bulk composition of the planet. Here we present the results of smoothed particle hydrodynamics simulations of high-velocity (up to {approx}5v {sub esc}) collisions between 1 and 10 M {sub +} planets of initially terrestrial composition to investigate the end stages of formation of extrasolar super-Earths. As found in previous simulations of collisions between smaller bodies, when collision energies exceed simple merging, giant impacts are divided into two regimes: (1) disruption and (2) hit-and-run (a grazing inelastic collision and projectile escape). Disruption occurs when the impact parameter is near zero, when the projectile mass is small compared to the target, or at extremely high velocities. In the disruption regime, we derive the criteria for catastrophic disruption (when half the total colliding mass is lost), the transition energy between accretion and erosion, and a scaling law for the change in bulk composition (iron-to-silicate ratio) resulting from collisional stripping of a mantle.

  18. A super-cusp divertor configuration for tokamaks

    SciTech Connect (OSTI)

    Ryutov, D. D.

    2015-10-19

    Our study demonstrates a remarkable flexibility of advanced divertor configurations created with the remote poloidal field coils. The emphasis here is on the configurations with three poloidal field nulls in the divertor area. We are seeking the structures where all three nulls lie on the same separatrix, thereby creating two zones of a very strong flux expansion, as envisaged in the concept of Takases cusp divertor. It turns out that the set of remote coils can produce a cusp divertor, with additional advantages of: (i) a large stand-off distance between the divertor and the coils and (ii) a thorough control that these coils exert over the fine features of the configuration. In reference to these additional favourable properties acquired by the cusp divertor, the resulting configuration could be called a super-cusp. General geometrical features of the three-null configurations produced by remote coils are described. Issues on the way to practical applications include the need for a more sophisticated control system and possible constraints related to excessively high currents in the divertor coils.

  19. Complexation of N4-Tetradentate Ligands with Nd(III) and Am(III)

    SciTech Connect (OSTI)

    Ogden, Mark D.; Sinkov, Sergey I.; Meier, G. Patrick; Lumetta, Gregg J.; Nash, Kenneth L.

    2012-12-06

    To improve understanding of aza-complexants in trivalent actinidelanthanide separations, a series of tetradentate N-donor ligands have been synthesized and their complexation of americium(III) and neodymium(III) investigated by UVvisible spectrophotometry in methanolic solutions. The six pyridine/alkyl amine/imine ligands are N,N0-bis(2-methylpyridyl)-1,2-diaminoethane, N,N0-bis(2-methylpyridyl)-1,3-diaminopropane, trans-N,N-bis(2-pyridylmethyl)-1,2-diaminocyclohexane (BPMDAC), N,N-bis(2-pyridylmethyl)piperazine, N,N-bis-[pyridin-2-ylmethylene]ethane-1,2-diamine, and trans-N,Nbis-([pyridin-2-ylmethylene]-cyclohexane-1,2-diamine. Each ligand has two pyridine groups and two aliphatic amine/imine N-donor atoms arranged with different degrees of preorganization and structural backbone rigidity. Conditional stability constants for the complexes of Am(III) and Nd(III) by these ligands establish the selectivity patterns. The overall selectivity of Am(III) over Nd(III) is similar to that reported for the terdentate bis(dialkyltriazinyl)pyridine molecules. The cyclohexane amine derivative (BPMDAC) is the strongest complexant and shows the highest selectivity for Am(III) over Nd(III) while the imines appear to prefer a bridging arrangement between two cations. These results suggest that this series of ligands could be employed to develop an enhanced actinide(III) lanthanide(III) separation system.

  20. Multijunction III-V Photovoltaics Research

    Broader source: Energy.gov [DOE]

    DOE invests in multijunction III-V solar cell research to drive down the costs of the materials, manufacturing, tracking techniques, and concentration methods used with this technology. Below is a...

  1. Panel Session III: Innovation and Coordination

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Lessons Learned for Hydrogen Panel Session III: Innovation Panel Session III: Innovation and Coordination and Coordination ______________________________ Stefan Unnasch Life Cycle Associates 3 April 2008 2 Hydrogen Vision Life Cycle Associates 3 Hydrogen Infrastructure Today Life Cycle Associates Source: Weinert, J. X., et al.. (2005). CA Hydrogen Highway Network Blueprint Plan, Economics Report 4 Innovation and Coordination Life Cycle Associates Innovation Coordination ☯ Slow Fast Cars Codes

  2. Jack R. Ferrell III | Bioenergy | NREL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Jack R. Ferrell III Jack R. Ferrell III Research Engineer Jack.Ferrell@nrel.gov | 303-384-7777 Research Interests Jack Ferrell works in the Thermochemical Catalysis Research and Development (R&D) group and manages tasks on analytical standardization for pyrolysis oil and on kinetic and hydrodynamic modeling of biomass-to-biofuels processes. Research interests include: Standardization of analytical techniques for the analysis of bio-oils Electrochemical upgrading of biomass-derived

  3. Isolation and microbial reduction of Fe(III) phyllosilicates...

    Office of Scientific and Technical Information (OSTI)

    Isolation and microbial reduction of Fe(III) phyllosilicates from subsurface sediments Citation Details In-Document Search Title: Isolation and microbial reduction of Fe(III) ...

  4. Klondike III II Wind Farm | Open Energy Information

    Open Energy Info (EERE)

    II Wind Farm Jump to: navigation, search Name Klondike III II Wind Farm Facility Klondike III Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service...

  5. Lamar Wind Energy Project III | Open Energy Information

    Open Energy Info (EERE)

    III Jump to: navigation, search Name Lamar Wind Energy Project III Facility Lamar Wind Energy Project Sector Wind energy Facility Type Commercial Scale Wind Facility Status In...

  6. Medicine Bow Wind Farm III | Open Energy Information

    Open Energy Info (EERE)

    III Jump to: navigation, search Name Medicine Bow Wind Farm III Facility Medicine Bow Sector Wind energy Facility Type Small Scale Wind Facility Status In Service Owner Platte...

  7. Design of Integrated III-Nitride/Non-III-Nitride Tandem Photovoltaic Devices

    SciTech Connect (OSTI)

    Toledo, N. G.; Friedman, D.J.; Farrell, R. M.; Perl, E. E.; Lin, C. T.; Bowers, J. E.; Speck, J. S.; Mishra, U. K.

    2012-03-01

    The integration of III-nitride and non-III-nitride materials for tandem solar cell applications can improve the efficiency of the photovoltaic device due to the added power contributed by the III-nitride top cell to that of high-efficiency multi-junction non-III-nitride solar cells if the device components are properly designed and optimized. The proposed tandem solar cell is comprised of a III-nitride top cell bonded to a non-III-nitride, series-constrained, multi-junction subcell. The top cell is electrically isolated, but optically coupled to the underlying subcell. The use of a III-nitride top cell is potentially beneficial when the top junction of a stand-alone non-III-nitride subcell generates more photocurrent than the limiting current of the non-III-nitride subcell. Light producing this excess current can either be redirected to the III-nitride top cell through high energy photon absorption, redirected to the lower junctions through layer thickness optimization, or a combination of both, resulting in improved total efficiency. When the non-III-nitride cell's top junction is the limiting junction, the minimum power conversion efficiency that the III-nitride top cell must contribute should compensate for the spectrum filtered from the multi-junction subcell for this design to be useful. As the III-nitride absorption edge wavelength, {lambda}{sub N}, increases, the performance of the multi-junction subcell decreases due to spectral filtering. In the most common spectra of interest (AM1.5G, AM1.5 D, and AM0), the technology to grow InGaN cells with {lambda}{sub N}<520 nm is found to be sufficient for III-nitride top cell applications. The external quantum efficiency performance, however, of state-of-the-art InGaN solar cells still needs to be improved. The effects of surface/interface reflections are also presented. The management of these reflection issues determines the feasibility of the integrated III-nitride/non-III-nitride design to improve overall cell

  8. TRUPACT-III Content Codes (TRUCON-III), Revision 2, July 2012

    Office of Environmental Management (EM)

    WIPP 11-3458 Rev. 2 TRUPACT-III CONTENT CODES (TRUCON-III) Revision 2 July 2012 This document supersedes DOE/WIPP 10-3458, Revision 1 DOE/WIPP 11-3458 Rev. 2 TRUPACT-III CONTENT CODES (TRUCON-III) Revision 2 July 2012 Approved by: [Signature on File] Date:_ 12 July 2012 _ J. R. Stroble, Director, Office of the National TRU Program DOE/WIPP 11-3458 Rev. 2, July 2012 3 This document has been submitted as required to: U.S. Department of Energy Office of Scientific and Technical Information PO Box

  9. A SUPER-EARTH TRANSITING A NAKED-EYE STAR

    SciTech Connect (OSTI)

    Winn, Joshua N.; Matthews, Jaymie M.; Kallinger, Thomas; Dragomir, Diana; Dawson, Rebekah I.; Holman, Matthew J.; Sasselov, Dimitar; Fabrycky, Daniel; Guenther, David B.; Moffat, Anthony F. J.; Rowe, Jason F.; Rucinski, Slavek

    2011-08-10

    We have detected transits of the innermost planet 'e' orbiting 55 Cnc (V = 6.0), based on two weeks of nearly continuous photometric monitoring with the MOST space telescope. The transits occur with the period (0.74 days) and phase that had been predicted by Dawson and Fabrycky, and with the expected duration and depth for the crossing of a Sun-like star by a hot super-Earth. Assuming the star's mass and radius to be 0.963{sup +0.051}{sub -0.029} M{sub sun} and 0.943 {+-} 0.010 R{sub sun}, the planet's mass, radius, and mean density are 8.63 {+-} 0.35 M{sub +}, 2.00 {+-} 0.14 R{sub +}, and 5.9{sup +1.5}{sub -1.1} g cm{sup -3}, respectively. The mean density is comparable to that of Earth, despite the greater mass and consequently greater compression of the interior of 55 Cnc e. This suggests a rock-iron composition supplemented by a significant mass of water, gas, or other light elements. Outside of transits, we detected a sinusoidal signal resembling the expected signal due to the changing illuminated phase of the planet, but with a full range (168 {+-} 70 ppm) too large to be reflected light or thermal emission. This signal has no straightforward interpretation and should be checked with further observations. The host star of 55 Cnc e is brighter than that of any other known transiting planet, which will facilitate future investigations.

  10. Super Boiler 2nd Generation Technology for Watertube Boilers

    SciTech Connect (OSTI)

    Mr. David Cygan; Dr. Joseph Rabovitser

    2012-03-31

    This report describes Phase I of a proposed two phase project to develop and demonstrate an advanced industrial watertube boiler system with the capability of reaching 94% (HHV) fuel-to-steam efficiency and emissions below 2 ppmv NOx, 2 ppmv CO, and 1 ppmv VOC on natural gas fuel. The boiler design would have the capability to produce >1500 F, >1500 psig superheated steam, burn multiple fuels, and will be 50% smaller/lighter than currently available watertube boilers of similar capacity. This project is built upon the successful Super Boiler project at GTI. In that project that employed a unique two-staged intercooled combustion system and an innovative heat recovery system to reduce NOx to below 5 ppmv and demonstrated fuel-to-steam efficiency of 94% (HHV). This project was carried out under the leadership of GTI with project partners Cleaver-Brooks, Inc., Nebraska Boiler, a Division of Cleaver-Brooks, and Media and Process Technology Inc., and project advisors Georgia Institute of Technology, Alstom Power Inc., Pacific Northwest National Laboratory and Oak Ridge National Laboratory. Phase I of efforts focused on developing 2nd generation boiler concepts and performance modeling; incorporating multi-fuel (natural gas and oil) capabilities; assessing heat recovery, heat transfer and steam superheating approaches; and developing the overall conceptual engineering boiler design. Based on our analysis, the 2nd generation Industrial Watertube Boiler when developed and commercialized, could potentially save 265 trillion Btu and $1.6 billion in fuel costs across U.S. industry through increased efficiency. Its ultra-clean combustion could eliminate 57,000 tons of NOx, 460,000 tons of CO, and 8.8 million tons of CO2 annually from the atmosphere. Reduction in boiler size will bring cost-effective package boilers into a size range previously dominated by more expensive field-erected boilers, benefiting manufacturers and end users through lower capital costs.

  11. Vadose Zone Soil Moisture Wicking Using Super Absorbent Polymers

    SciTech Connect (OSTI)

    Oostrom, Martinus; Smoot, Katherine V.; Wietsma, Thomas W.; Truex, Michael J.; Benecke, Mark W.; Chronister, Glen B.

    2012-11-19

    Super-absorbent polymers (SAPs) have the potential to remove water and associated contaminants from unsaturated sediments in the field. Column and flow cell experiment were conducted to test the ability of four types of SAPs to remove water from unsaturated porous media. Column experiments, with emplacement of a layer of polymer on top of unsaturated porous media, showed the ability of the SAPs to extract up to 80% of the initially emplaced water against gravity into the sorbent over periods up to four weeks. In column experiments where the sorbent was emplaced between layers of unsaturated porous media, gel formation was observed at both the sorbent-porous medium interfaces. The extraction percentages over four weeks of contact time were similar for both column configurations and no obvious differences were observed for the four tested SAPs. Two different flow cells were used to test the wicking behavior of SAPs in two dimensions using three configurations. The largest removal percentages occurred for the horizontal sorbent layer configuration which has the largest sorbent-porous medium interfacial area. In a larger flow cell, a woven nylon sock was packed with sorbent and subsequently placed between perforated metal plates, mimicking a well configuration. After one week of contact time the sock was removed and replaced by a fresh sock. The results of this experiment showed that the sorbent was able to continuously extract water from the porous media, although the rate decreased over time. The declining yield during both periods is associated with the sharp reduction in water saturation and relative permeability near the sorbent. It was also observed that the capillary pressure continued to increase over the total contact time of 14 days, indicating that the sorbent remained active over that period. This work has demonstrated the potential of soil moisture wicking using SAPs at the proof-of-principle level.

  12. NEAR-INFRARED DETECTION OF A SUPER-THIN DISK IN NGC 891

    SciTech Connect (OSTI)

    Schechtman-Rook, Andrew; Bershady, Matthew A.

    2013-08-10

    We probe the disk structure of the nearby, massive, edge-on spiral galaxy NGC 891 with subarcsecond resolution JHK{sub s}-band images covering {approx} {+-}10 kpc in radius and {+-}5 kpc in height. We measure intrinsic surface brightness (SB) profiles using realistic attenuation corrections constrained from near- and mid-infrared (Spitzer) color maps and three-dimensional Monte Carlo radiative-transfer models. In addition to the well-known thin and thick disks, a super-thin disk with 60-80 pc scale-height-comparable to the star-forming disk of the Milky Way-is visibly evident and required to fit the attenuation-corrected light distribution. Asymmetries in the super-thin disk light profile are indicative of young, hot stars producing regions of excess luminosity and bluer (attenuation-corrected) near-infrared color. To fit the inner regions of NGC 891, these disks must be truncated within {approx}3 kpc, with almost all their luminosity redistributed in a bar-like structure 50% thicker than the thin disk. There appears to be no classical bulge but rather a nuclear continuation of the super-thin disk. The super-thin, thin, thick, and bar components contribute roughly 30%, 42%, 13%, and 15% (respectively) to the total K{sub s}-band luminosity. Disk axial ratios (length/height) decrease from 30 to 3 from super-thin to thick components. Both exponential and sech{sup 2} vertical SB profiles fit the data equally well. We find that the super-thin disk is significantly brighter in the K{sub s}-band than typically assumed in integrated spectral energy distribution models of NGC 891: it appears that in these models the excess flux, likely produced by young stars in the super-thin disk, has been mistakenly attributed to the thin disk.

  13. New Mexico cloud super cooled liquid water survey final report 2009.

    SciTech Connect (OSTI)

    Beavis, Nick; Roskovensky, John K.; Ivey, Mark D.

    2010-02-01

    Los Alamos and Sandia National Laboratories are partners in an effort to survey the super-cooled liquid water in clouds over the state of New Mexico in a project sponsored by the New Mexico Small Business Assistance Program. This report summarizes the scientific work performed at Sandia National Laboratories during the 2009. In this second year of the project a practical methodology for estimating cloud super-cooled liquid water was created. This was accomplished through the analysis of certain MODIS sensor satellite derived cloud products and vetted parameterizations techniques. A software code was developed to analyze multiple cases automatically. The eighty-one storm events identified in the previous year effort from 2006-2007 were again the focus. Six derived MODIS products were obtained first through careful MODIS image evaluation. Both cloud and clear-sky properties from this dataset were determined over New Mexico. Sensitivity studies were performed that identified the parameters which most influenced the estimation of cloud super-cooled liquid water. Limited validation was undertaken to ensure the soundness of the cloud super-cooled estimates. Finally, a path forward was formulized to insure the successful completion of the initial scientific goals which include analyzing different of annual datasets, validation of the developed algorithm, and the creation of a user-friendly and interactive tool for estimating cloud super-cooled liquid water.

  14. The superTIGER instrument: Measurement of elemental abundances of ultra-heavy galactic cosmic rays

    SciTech Connect (OSTI)

    Binns, W. R.; Bose, R. G.; Braun, D. L.; Dowkontt, P. F.; Israel, M. H.; Moore, P.; Murphy, R. P.; Olevitch, M. A.; Rauch, B. F.; Brandt, T. J.; Daniels, W. M.; Fitzsimmons, S. P.; Hahne, D. J.; Hams, T.; Link, J. T.; Mitchell, J. W.; Sakai, K.; and others

    2014-06-10

    The SuperTIGER (Super Trans-Iron Galactic Element Recorder) instrument was developed to measure the abundances of galactic cosmic-ray elements from {sub 10}Ne to {sub 40}Zr with individual element resolution and the high statistics needed to test models of cosmic-ray origins. SuperTIGER also makes exploratory measurements of the abundances of elements with 40 < Z ≤ 60 and measures the energy spectra of the more abundant elements for Z ≤ 30 from about 0.8 to 10 GeV/nucleon. This instrument is an enlarged and higher resolution version of the earlier TIGER instrument. It was designed to provide the largest geometric acceptance possible and to reach as high an altitude as possible, flying on a standard long-duration 1.11 million m{sup 3} balloon. SuperTIGER was launched from Williams Field, McMurdo Station, Antarctica, on 2012 December 8, and made about 2.7 revolutions around the South Pole in 55 days of flight, returning data on over 50 × 10{sup 6} cosmic-ray nuclei with Z ≥ 10, including ∼1300 with Z > 29 and ∼60 with Z > 49. Here, we describe the instrument, the methods of charge identification employed, the SuperTIGER balloon flight, and the instrument performance.

  15. SBIR_Phase_III.pdf | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SBIR_Phase_III.pdf SBIR_Phase_III.pdf (228.04 KB) More Documents & Publications PROJECT SELECTIONS FOR DOE PHASE III XLERATOR SMALL BUSINESS PROGRAM - pg 3 PROJECT SELECTIONS FOR DOE PHASE III XLERATOR SMALL BUSINESS PROGRAM Albany HTS Power Cable

  16. Molten-Salt-Based Growth of Group III Nitrides

    DOE Patents [OSTI]

    Waldrip, Karen E.; Tsao, Jeffrey Y.; Kerley, Thomas M.

    2008-10-14

    A method for growing Group III nitride materials using a molten halide salt as a solvent to solubilize the Group-III ions and nitride ions that react to form the Group III nitride material. The concentration of at least one of the nitride ion or Group III cation is determined by electrochemical generation of the ions.

  17. Final Report: Super Instruction Architecture for Scalable Parallel Computations

    SciTech Connect (OSTI)

    Sanders, Beverly Ann; Bartlett, Rodney; Deumens, Erik

    2013-12-23

    The most advanced methods for reliable and accurate computation of the electronic structure of molecular and nano systems are the coupled-cluster techniques. These high-accuracy methods help us to understand, for example, how biological enzymes operate and contribute to the design of new organic explosives. The ACES III software provides a modern, high-performance implementation of these methods optimized for high performance parallel computer systems, ranging from small clusters typical in individual research groups, through larger clusters available in campus and regional computer centers, all the way to high-end petascale systems at national labs, including exploiting GPUs if available. This project enhanced the ACESIII software package and used it to study interesting scientific problems.

  18. Doublet III neutral beam power system

    SciTech Connect (OSTI)

    Nerem, A.; Beal, J.W.; Colleraine, A.P.; LeVine, F.H.; Pipkins, J.F.; Remsen, D.B. Jr.; Tooker, J.F.; Varga, H.J.; Franck, J.V.

    1981-01-01

    The Doublet III neutral beam power system supplies pulsed power to the neutral beam injectors for plasma heating experiments on the Doublet III tokamak. The power supply system is connected to an ion source where the power is converted to an 80 kV, 80A, 0.5 sec beam of hydrogen ions at maximum power output. These energetic ions undergo partial neutralization via charge exchange in the beamline. The energetic neutral hydrogen atoms pass through the Doublet III toroidal and poloidal magnet fields and deposit their energy in the confined plasma. The unneutralized ions are deflected into a water-cooled dump. The entire system is interfaced through the neutral beam computer instrumentation and control system.

  19. Analysis of Godiva-IV delayed-critical and static super-prompt-critical conditions

    SciTech Connect (OSTI)

    Mosteller, Russell D; Goda, Joetta M

    2009-01-01

    Super-prompt-critical burst experiments were conducted on the Godiva-IV assembly at Los Alamos National Laboratory from the 1960s through 2005. Detailed and simplified benchmark models have been constructed for four delayed-critical experiments and for the static phase of a super-prompt-critical burst experiment. In addition, a two-dimensional cylindrical model has been developed for the super-prompt-critical condition. Criticality calculations have been performed for all of those models with four modern nuclear data libraries: ENDFIB-VI, ENDF/8-VII.0, JEFF-3.1 , and JENDL-3.3. Overall, JENDL-3.3 produces the best agreement with the reference values for k{sub eff}.

  20. SUPER-CRITICAL GROWTH OF MASSIVE BLACK HOLES FROM STELLAR-MASS SEEDS

    SciTech Connect (OSTI)

    Madau, Piero; Haardt, Francesco; Dotti, Massimo

    2014-04-01

    We consider super-critical accretion with angular momentum onto stellar-mass black holes as a possible mechanism for growing billion-solar-mass black holes from light seeds at early times. We use the radiatively inefficient ''slim disk'' solutionadvective, optically thick flows that generalize the standard geometrically thin disk modelto show how mildly super-Eddington intermittent accretion may significantly ease the problem of assembling the first massive black holes when the universe was less than 0.8Gyr old. Because of the low radiative efficiencies of slim disks around non-rotating as well as rapidly rotating black holes, the mass e-folding timescale in this regime is nearly independent of the spin parameter. The conditions that may lead to super-critical growth in the early universe are briefly discussed.

  1. SuperB Bunch-By-Bunch Feedback R&D

    SciTech Connect (OSTI)

    Drago, A.; Beretta, M.; Bertsche, K.; Novokhatski, A.; Migliorati, M.; /Rome U.

    2011-08-12

    The SuperB project has the goal to build in Italy, in the Frascati or Tor Vergata area, an asymmetric e{sup +}/e{sup -} Super Flavor Factory to achieve a peak luminosity > 10**36 cm{sup -2} s{sup -1}. The SuperB design is based on collisions with extremely low vertical emittance beams and high beam currents. A source of emittance growth comes from the bunch by bunch feedback systems producing high power correction signals to damp the beams. To limit any undesirable effect, a large R&D program is in progress, partially funded by the INFN Fifth National Scientific Committee through the SFEED (SuperB Feedback) project approved within the 2010 budget. The SuperB project [1] has the goal to build in Italy, in the Frascati or Tor Vergata area, an asymmetric e{sup +}/e{sup -} Super Flavor Factory to achieve a peak luminosity > 10**36 cm{sup -2} s{sup -1}. In the last and current years, the machine layout has been deeply modified, in particular the main rings are now shorter and an option with high currents has been foreseen. In the fig.1 the new SuperB layout is shown. From bunch-by-bunch feedback point of view, the simultaneous presence in the machine parameters, of very low emittance, of the order of 5-10 pm in the vertical plane, and very high currents, at level of 4 Ampere for the Low Energy Ring, asks for designing very carefully the bunch-by-bunch feedback systems. The parameter list is presented in Fig. 2. The bunch-by-bunch feedback design must take care of the risky and exciting challenges proposed in the SuperB specifications, but it should consider also some other important aspects: flexibility in terms of being able to cope to unexpected beam behaviours [2], [3] legacy of previous version experience [4], [5] and internal powerful diagnostics [6] as in the systems previously used in PEP-II and DAFNE [7].

  2. SuperTruck Making Leaps in Fuel Efficiency | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SuperTruck Making Leaps in Fuel Efficiency SuperTruck Making Leaps in Fuel Efficiency February 19, 2014 - 12:37pm Addthis This Class 8 tractor-trailer by heavy-duty manufacturers Cummins and Peterbilt reaches more than 10 miles per gallon under real world driving conditions. The truck was on display at the Energy Department today. | Photo by <a href="http://www.energy.gov/contributors/sarah-gerrity">Sarah Gerrity</a>, Energy Department This Class 8 tractor-trailer by

  3. Super-radiance in the sodium resonance lines from sodium iodide arc lamps

    SciTech Connect (OSTI)

    Karabourniotis, D.; Drakakis, E.

    2010-08-09

    Super-radiance observed within the centers of the sodium resonance D lines emitted by arc lamps containing sodium iodide as additive in a high-pressure mercury plasma environment was studied by high-resolution emission spectroscopy. The spectral radiance of these self-reversed lines including super-radiance was simulated by considering a local enhancement of the source function due to the presence of an additional source of radiation near the arc wall. Causes of this hitherto unrecognized source of radiation are given.

  4. 5 Super-Sized Solar Projects Transforming the Clean Energy Landscape |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Super-Sized Solar Projects Transforming the Clean Energy Landscape 5 Super-Sized Solar Projects Transforming the Clean Energy Landscape April 8, 2013 - 4:00pm Addthis The California Valley Solar Ranch has a capacity of 250 MW -- enough energy to power the equivalent of every home in San Luis Obispo County. | Photo courtesy of SunPower. The California Valley Solar Ranch has a capacity of 250 MW -- enough energy to power the equivalent of every home in San Luis Obispo

  5. Sub-to super-ambient temperature programmable microfabricated gas chromatography column

    DOE Patents [OSTI]

    Robinson, Alex L.; Anderson, Lawrence F.

    2004-03-16

    A sub- to super-ambient temperature programmable microfabricated gas chromatography column enables more efficient chemical separation of chemical analytes in a gas mixture by combining a thermoelectric cooler and temperature sensing on the microfabricated column. Sub-ambient temperature programming enables the efficient separation of volatile organic compounds and super-ambient temperature programming enables the elution of less volatile analytes within a reasonable time. The small heat capacity and thermal isolation of the microfabricated column improves the thermal time response and power consumption, both important factors for portable microanalytical systems.

  6. Fabrication of super-hydrophobic surfaces on aluminum alloy substrates by RF-sputtered polytetrafluoroethylene coatings

    SciTech Connect (OSTI)

    Wang, Yang; Liu, Xiao Wei; Zhang, Hai Feng Zhou, Zhi Ping

    2014-03-15

    In this work, we present a method of fabricating super-hydrophobic surface on aluminum alloy substrate. The etching of aluminum surfaces has been performed using Beck's dislocation etchant for different time to create micrometer-sized irregular steps. An optimised etching time of 50 s is found to be essential before polytetrafluoroethylene (PTFE) coating, to obtain a highest water contact angle of 1652 with a lowest contact angle hysteresis as low as 52. The presence of patterned microstructure as revealed by scanning electron microscopy (SEM) together with the low surface energy ultrathin RF-sputtered PTFE films renders the aluminum alloy surfaces highly super-hydrophobic.

  7. Photodetectors using III-V nitrides

    DOE Patents [OSTI]

    Moustakas, Theodore D.

    1998-01-01

    A bandpass photodetector using a III-V nitride and having predetermined electrical properties. The bandpass photodetector detects electromagnetic radiation between a lower transition wavelength and an upper transition wavelength. That detector comprises two low pass photodetectors. The response of the two low pass photodetectors is subtracted to yield a response signal.

  8. Photodetectors using III-V nitrides

    DOE Patents [OSTI]

    Moustakas, T.D.

    1998-12-08

    A bandpass photodetector using a III-V nitride and having predetermined electrical properties is disclosed. The bandpass photodetector detects electromagnetic radiation between a lower transition wavelength and an upper transition wavelength. That detector comprises two low pass photodetectors. The response of the two low pass photodetectors is subtracted to yield a response signal. 24 figs.

  9. DESIGNING AND OPPORTUNITY FUEL WITH BIOMASS AND TIRE-DERIVED FUEL FOR COFIRING AT WILLOW ISLAND GENERATING STATION AND COFIRING SAWDUST WITH COAL AT ALBRIGHT GENERATING STATION

    SciTech Connect (OSTI)

    K. Payette; D. Tillman

    2004-06-01

    During the period July 1, 2000-March 31, 2004, Allegheny Energy Supply Co., LLC (Allegheny) conducted an extensive demonstration of woody biomass cofiring at its Willow Island and Albright Generating Stations. This demonstration, cofunded by USDOE and Allegheny, and supported by the Biomass Interest Group (BIG) of EPRI, evaluated the impacts of sawdust cofiring in both cyclone boilers and tangentially-fired pulverized coal boilers. The cofiring in the cyclone boiler--Willow Island Generating Station Unit No.2--evaluated the impacts of sawdust alone, and sawdust blended with tire-derived fuel. The biomass was blended with the coal on its way to the combustion system. The cofiring in the pulverized coal boiler--Albright Generating Station--evaluated the impact of cofiring on emissions of oxides of nitrogen (NO{sub x}) when the sawdust was injected separately into the furnace. The demonstration of woody biomass cofiring involved design, construction, and testing at each site. The results addressed impacts associated with operational issues--capacity, efficiency, and operability--as well as formation and control of airborne emissions such as NO{sub x}, sulfur dioxide (SO{sub 2}2), opacity, and mercury. The results of this extensive program are detailed in this report.

  10. Summary audit report on lessons learned from the Superconducting Super Collider Project

    SciTech Connect (OSTI)

    1996-04-23

    In October 1993, the Congress decided to terminate the Superconducting Super Collider (SSC) project after expending about $1.57 billion on the project. While both internal and external factors contributed to the demise of the project, its cancellation offers the Department a unique opportunity to analyze what went wrong, correct the mistakes, and apply the lessons learned to future large-scale projects.

  11. Cryogenic systems for the HEB accelerator of the Superconducting Super Collider

    SciTech Connect (OSTI)

    Abramovich, S.; Yuecel, A.

    1994-07-01

    This report discusses the following topics related to the Superconducting Super Collider: Cryogenic system -- general requirements; cryogenic system components; heat load budgets and refrigeration plant capacities; flow and thermal characteristics; process descriptions; cryogenic control instrumentation and value engineering trade-offs.

  12. Muon simulations for Super-Kamiokande, KamLAND, and CHOOZ

    SciTech Connect (OSTI)

    Tang, Alfred; Horton-Smith, Glenn; Kudryavtsev, Vitaly A.; Tonazzo, Alessandra

    2006-09-01

    Muon backgrounds at Super-Kamiokande, KamLAND, and CHOOZ are calculated using MUSIC. A modified version of the Gaisser sea-level muon distribution and a well-tested Monte Carlo integration method are introduced. Average muon energy, flux, and rate are tabulated. Plots of average energy and angular distributions are given. Implications for muon tracker design in future experiments are discussed.

  13. Contracting practices for the underground construction of the Superconducting Super Collider

    SciTech Connect (OSTI)

    Not Available

    1989-01-01

    This report was prepared by a specially appointed committee under the auspices of the National Academy of Sciences/National Research Council to address contracting and associated management issues essential to the successful execution of underground construction for the Superconducting Super Collider.

  14. Physical meaning of gauge and super-gauge in general-relativistic field theories

    SciTech Connect (OSTI)

    Treder, H.

    1985-05-01

    The physical meaning of gauge groups in bimetrical, Riemannian, and Hermitian theories of gravitation is discussed. In Hermitian relativity, Einstein's A-invariance means a super-gauge group which characterizes the Einstein-Schroedinger equations as the only nondegenerate general-relativistic field theory.

  15. Brookhaven National Laboratory - OU III VOC | Department of Energy

    Office of Environmental Management (EM)

    III VOC Brookhaven National Laboratory - OU III VOC January 1, 2014 - 12:00pm Addthis US ... InstallationName, State: Brookhaven National Laboratory Responsible DOE Office: Office of ...

  16. Microsoft Word - SECARB Phase III CO2 sequestration Final EA...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Phase III Early Test March 2009 U.S. DEPARTMENT OF ENERGY NATIONAL ENERGY TECHNOLOGY LABORATORY U.S. Department of Energy SECARB Phase III Early Test National Energy ...

  17. Implementation of Division D, Titles III and V, and Division...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and guidance for Division D, Titles III and V, and Division E, Title VII of the ... Implementation of Division D, Titles III and V, and Division E, Title VII of the ...

  18. Integrated Biorefinery Research Facility (IBRF I-II) (Post CD...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Integrated Biorefinery Research Facility (IBRF I-II) (Post CD-4), EERE, Aug 2011 Integrated Biorefinery Research Facility (IBRF I-II) (Post CD-4), EERE, Aug 2011 PDF icon 000521 & ...

  19. PROJECT SELECTIONS FOR DOE PHASE III XLERATOR SMALL BUSINESS...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PROJECT SELECTIONS FOR DOE PHASE III XLERATOR SMALL BUSINESS PROGRAM - pg 3 PROJECT SELECTIONS FOR DOE PHASE III XLERATOR SMALL BUSINESS PROGRAM - pg 3 PDF icon sbirphase3pg3.pdf...

  20. M r. Andrew Wallo, III, NE-23

    Office of Legacy Management (LM)

    300.955 L*Enfom Plaza, S. Iv.. Washrhington. D.C. 200242174, Tekphonc (202) 7117-03.87.cdy.43 23 September 1987 M r. Andrew Wallo, III, NE-23 Division of Facility & Site Deconnnissioning Projects U.S. Department of Energy Germantown, Maryland 20545 Dear M r. Wallo: ELIMINATION RECOMMENDATION -- COLLEGES AND UNIVERSITIES The attached elimination recommendation was prepared in accordi with your suggestion during our meeting on 22 September. The reconu includes 26 colleges and universities

  1. J. Taylor Childers III | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    J. Taylor Childers III Assistant Physicist Education 2002 - 2007 University of Minnesota, PhD. in Physics 1998 - 2002 University of Kentucky, BS. in Physics Experience 2013 - present Assistant Physicist at Argonne National Lab, Chicago, IL, USA 2011 - 2013 Fellow at CERN, Geneva, Switzerland 2007 - 2011 Postdoctoral Researcher at Heidelberg University, Heidelberg, Germany Summary of Research I am an Assistant Physicist at Argonne National Laboratory in Chicago, USA. As a member of ATLAS, I am

  2. III. PROGRAM-SPECIFIC COMPLIANCE SUPPLEMENTS

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    III. PROGRAM-SPECIFIC COMPLIANCE SUPPLEMENTS For fiscal year 2010, no DOE programs have compliance requirements that are distinct from the general compliance requirements included in Part II of this guidance (General Compliance Supplement). Therefore, audits of recipients and subrecipients with fiscal years ending in 2010 should be conducted in accordance with the compliance requirements included in Part II of this guidance. For fiscal years subsequent to 2010, program-specific compliance

  3. Chapter III: Modernizing the Electric Grid

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    3-34 QER Report: Energy Transmission, Storage, and Distribution Infrastructure | April 2015 Chapter III: Modernizing the Electric Grid QER Report: Energy Transmission, Storage, and Distribution Infrastructure | April 2015 4-1 Chapter IV This chapter addresses the role of infrastructure in ensuring U.S. energy security in a global marketplace. It first describes the evolution of the concept of U.S. energy security in response to interconnected global energy markets. It then discusses the security

  4. Microsoft Word - AR OU III April 09 subject.doc

    Office of Legacy Management (LM)

    Administrative Record, Monticello Mill Tailings Site Operable Unit III, Subject Index April 2009 File Index: MRAP 1.11 page 1 of 10 Administrative Record for the U.S. Department of Energy Monticello Mill Tailings Site (MMTS), Operable Unit III (OU III), Monticello Ground Water Remedial Action Project (MSGRAP) Monticello, Utah Subject Index Note: This Administrative Record contains documents specifically relevant to Operable Unit III leading up to the Record of Decision in October 2004. Later

  5. Raft River III Geothermal Project | Open Energy Information

    Open Energy Info (EERE)

    Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Development Project: Raft River III Geothermal Project Project Location Information Coordinates...

  6. Title III of the Omnibus Appropriations Act | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    III of the Omnibus Appropriations Act Title III of the Omnibus Appropriations Act Title III of the Omnibus Appropriations Act (1.28 MB) More Documents & Publications American Recovery and Reinvestment Act of 2009 Section 129 of the Consolidated Security, Disaster Assistance, and Continuing Appropriations Act Methane Hydrate Research and Development Act of 2000

  7. SuperShuttle CNG Fleet Study Summary: Clean Cities Alternative Fuel Information Series, Alternative Fuel Case Study

    SciTech Connect (OSTI)

    Eudy, L.

    2001-03-05

    An account of the successful use of alternative fuels in a fleet of SuperShuttle passenger vans, which offer shared-rides between Boulder and Denver International Airport.

  8. Mr. Andrew Wallo, III, NE-23

    Office of Legacy Management (LM)

    300, 955 L'E~~MI Phm.SW.:. Washin@on. LX. 200242174, T~kphonc(202)48ll. 5 7117-03.87.cdy.43 23 September 1987 cA Mr. Andrew Wallo, III, NE-23 Division of Facility & Site Decommissioning Projects U.S. Department of Energy Germantown, Maryland 20545 Dear Mr. Wallo: ELIMINATION RECOMMENDATION -- COLLEGES AND UNIVERSITIES M/).0-05 pl 0.0% The attached elimination recommendation was prepared in accordance ML.05 with your suggestion during our meeting on 22 September. The recommendation flD.o-02

  9. Mr. Andrew Wallo, III, NE-23

    Office of Legacy Management (LM)

    9% L'Enfam Plaza, S, W.. Warhin@on, D.C. 2002ijl74j Tekphow (202) 488ddO 7117-03.87.cdy.'i3 23 September 1967 ~ s ~ Mr. Andrew Wallo, III, NE-23 Oivision of Facility & Site Decommissioning Projects U.S. Department of Energy Germantown, Maryland 20545 Dear Mr. Wallo: ELIMINATION RECOMMENDATION -- COLLEGES AND IJNIVFRSITIES , The attached elimination reconnnendation was prepar!ad in accordance with your suggestion during our meeting on 22 September! The recommendation includes 26 colleges and

  10. Mr. Andrew Wallo, III, NE-23

    Office of Legacy Management (LM)

    suite 7900,955 L%l/onr Plaza, S. W., Washingion, D.C. 20024.?174,, Telephone: (202) 488.~ Mr. Andrew Wallo, III, NE-23 Division of Facility & Site Decommissioning Projects U.S. Department of Energy Germantown, Maryland 20545 7117~03.87.dy.43 23 September 1987 I j / Dear Mr. Wallo: I ELIMINATION RECOMMENDATION -- COLLEGES AND UN&ITIES I . The attached elimination recommendation was prepared in accordance with your suggestion during our meeting on 22 September!. The recommend includes 26

  11. Proceedings: Substation equipment diagnostics conference III. Proceedings

    SciTech Connect (OSTI)

    1996-03-01

    This Substation Equipment Diagnostics Conference III was held to review the status of transmission substation diagnostics by EPRI, as well as that of the universities, manufacturers, testing organizations, and other researchers. The papers presented were organized under three categories of diagnostics: Transformers, Miscellaneous Equipment, and Systems. A reception on the evening of the first day of the Conference provided an opportunity for the researchers, utilities and manufacturers to display their equipment for the attendees. Separate abstracts have been indexed into the database for articles from this conference.

  12. Consent Order of Dismissal, Section III

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 SRR-ESH-2013-00054 Revision 1 August 28, 2013 Page 1 of 6 Consent Order of Dismissal, Section III.7 Z-Area Saltstone Disposal Facility Permit General Condition B.5.a-h Information Permit Condition Requirement Estimated Value Updated Value Comments B.5 a) Cumulative process volume of salt waste disposed to date Not Applicable 7,845 kgals Vault 4, Cells B, D, E, F, H, J, K, L SDU 2, Cells 2A and 2B b) Process volume of saltstone grout disposed and vault/disposal unit location (including cell

  13. Consent Order of Dismissal, Section III

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 SRR-ESH-2014-00039 Revision 1 August 28, 2014 Page 1 of 6 Z-Area Saltstone Disposal Facility Permit General Condition B.5.a-h Information and Consent Order of Dismissal, Section III.7 Permit Condition Requirement Estimated Value Updated Value Comments B.5 a) Cumulative process volume of salt waste disposed to date Not Applicable 8,770 kgals Vault 4, Cells B, D, E, F, H, J, K, L SDU 2, Cells 2A and 2B SDU 5, Cell 5B b) Process volume of saltstone grout disposed and vault/disposal unit location

  14. Consent Order of Dismissal, Section III

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 SRR-ESH-2014-00076 Revision 1 Posted Date: December 2, 2014 Page 1 of 6 Z-Area Saltstone Disposal Facility Permit General Condition B.5.a-h Information and Consent Order of Dismissal, Section III.7 Permit Condition Requirement Estimated Value Updated Value Comments B.5 a) Cumulative process volume of salt waste disposed to date Not Applicable 9,066 kgal Vault 4, Cells B, D, E, F, H, J, K, L SDU 2, Cells 2A and 2B SDU 5, Cell 5B b) Process volume of saltstone grout disposed and vault/disposal

  15. Consent Order of Dismissal, Section III

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 SRR-ESH-2015-00014 Revision 1 Posted Date: May 29, 2015 Page 1 of 6 Z-Area Saltstone Disposal Facility Permit General Condition B.5.a-h Information and Consent Order of Dismissal, Section III.7 Permit Condition Requirement Estimated Value Updated Value Comments B.5 a) Cumulative process volume of salt waste disposed to date Not Applicable 9,894 kgal Vault 4, Cells B, D, E, F, H, J, K, L SDU 2, Cells 2A and 2B SDU 5, Cell 5B b) Process volume of saltstone grout disposed and vault/disposal unit

  16. Consent Order of Dismissal, Section III

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 SRR-ESH-2015-00110 Revision 1 Post Date: February 29, 2016 Page 1 of 6 Z-Area Saltstone Disposal Facility Permit General Condition B.5.a-h Information and Consent Order of Dismissal, Section III.7 Permit Condition Requirement Estimated Value Updated Value Comments B.5 a) Cumulative process volume of salt waste disposed to date Not Applicable 10, 722 kgal Vault 4, Cells B, D, E, F, H, J, K, L SDU 2, Cells 2A and 2B SDU 5, Cells 5A and 5B b) Process volume of saltstone grout disposed and

  17. Consent Order of Dismissal, Section III

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 SRR-ESH-2016-00025 Revision 1 Post Date: May 27, 2016 Page 1 of 6 Z-Area Saltstone Disposal Facility Permit General Condition B.5.a-h Information and Consent Order of Dismissal, Section III.7 Permit Condition Requirement Estimated Value Updated Value Comments B.5 a) Cumulative process volume of salt waste disposed to date Not Applicable 10, 744 kgal SDU 4, Cells B, D, E, F, H, J, K, L SDU 2, Cells A and B SDU 5, Cells A and B b) Process volume of saltstone grout disposed and vault/disposal

  18. Consent Order of Dismissal, Section III

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6 SRR-ESH-2016-00052 Revision 1 Post Date: August 26, 2016 Page 1 of 6 Z-Area Saltstone Disposal Facility Permit General Condition B.5.a-h Information and Consent Order of Dismissal, Section III.7 Permit Condition Requirement Estimated Value Updated Value Comments B.5 a) Cumulative process volume of salt waste disposed to date Not Applicable 11,143 kgal SDU 4, Cells B, D, E, F, H, J, K, L SDU 2, Cells A and B SDU 5, Cells A and B b) Process volume of saltstone grout disposed and vault/disposal

  19. Consent Order of Dismissal, Section III

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6 SRR-ESH-2016-00068 Revision 0 Post Date: August 26, 2016 Page 1 of 6 Z-Area Saltstone Disposal Facility Permit General Condition B.5.a-h Information and Consent Order of Dismissal, Section III.7 Permit Condition Requirement Estimated Value Updated Value Comments B.5 a) Cumulative process volume of salt waste disposed to date Not Applicable 11,610 kgal SDU 4, Cells B, D, E, F, H, J, K, L SDU 2, Cells A and B SDU 5, Cells A and B b) Process volume of saltstone grout disposed and vault/disposal

  20. Consent Order of Dismissal, Section III

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 SRR-ESH-2015-00052 Revision 1 Post Date: August 28, 2015 Page 1 of 6 Z-Area Saltstone Disposal Facility Permit General Condition B.5.a-h Information and Consent Order of Dismissal, Section III.7 Permit Condition Requirement Estimated Value Updated Value Comments B.5 a) Cumulative process volume of salt waste disposed to date Not Applicable 9,948 kgal Vault 4, Cells B, D, E, F, H, J, K, L SDU 2, Cells 2A and 2B SDU 5, Cell 5B b) Process volume of saltstone grout disposed and vault/disposal unit

  1. CA Mr. Andrew Wallo, III, NE-23

    Office of Legacy Management (LM)

    ?9OQ, 95.5 L'E&nt Plaza, SW.. W.ashin@.m, D.C. 20024.2174, Tekphone: (202) 488AQOO 7117-03.B7.cdy.43 23 September 1987 CA Mr. Andrew Wallo, III, NE-23 Division of Facility & Site Decommissioning Projects U.S. Oepartment of Energy Germantown, Maryland 20545 Dear Mr. Wallo: ELIMINATION RECOMMENDATION -- COLLEGES AND UNIVERSITIES zh/ ! o-01 lM!tl5 ML)!o-05 PI 77!0> The attached elimination recoannendation was prepared in accordance . -1 rlL.0~ with your suggestion during our meeting on

  2. Proteome of Geobacter sulfurreducens grown with Fe(III) oxide or Fe(III) citrate as the electron acceptor.

    SciTech Connect (OSTI)

    Ding, Y-H R.; Hixson, Kim K.; Aklujkar, Ma; Lipton, Mary S.; Smith, Richard D.; Lovley, Derek R.; Mester, Tunde

    2008-12-01

    e(III) oxides are the most abundant source of reducible Fe(III) by microorganisms in most soils and sediments, yet few studies on the physiology of Fe(III)-reducing microorganisms during growth on Fe(III) oxide have been conducted because of the technical difficulties in working with cell growth and harvest in the presence of Fe(III) oxides. Geobacter sulfurreducens is a representative of the Geobacter species that predominate in a variety of subsurface environments in which Fe(III) oxide is important. In order to better understand the physiology of Geobacter species during growth on Fe(III) oxide, the proteome of G. sulfurreducens grown on Fe(III) oxide was compared with the proteome of cells grown with soluble Fe(III) citrate. Two-dimensional polyacrylamide gel electrophoresis (2-D PAGE) revealed 19 proteins that were more abundant during growth on Fe(III) oxide than on soluble Fe(III). These included proteins related to protein synthesis, electron transfer and energy production, oxidative stress, protein folding, outer membrane proteins, nitrogen metabolism and hypothetical proteins. Further analysis of the proteome with the accurate mass and time (AMT) tag method revealed additional proteins associated with growth on Fe(III) oxide. These included the outer-membrane c-type cytochrome, OmcS and OmcG, which genetic studies have suggested are required for Fe(III) oxide reduction. Furthermore, several other cytochromes, as yet unstudied, were detected to be significantly up regulated during growth on Fe(III) oxide and other proteins of unknown function were more abundant during growth on Fe(III) oxide than on soluble Fe(III). PilA, the structural protein for pili, which is required for Fe(III) oxide reduction, and other pilin-associated proteins were also more abundant during growth on Fe(III) oxide. Confirmation of the differential expression of proteins known to be important in Fe(III) oxide reduction was observed, and an additional number of previously

  3. Touschek Background and Lifetime Studies for the SuperB Factory

    SciTech Connect (OSTI)

    Boscolo, M.; Biagini, M.; Raimondi, P.; Sullivan, M.; Paoloni, E.; /INFN, Pisa

    2010-08-26

    The novel crab waist collision scheme under test at the DA{Phi}NE Frascati {Phi}-factory finds its natural application to the SuperB project, the asymmetric e{sup +}e{sup -} flavour factory at very high luminosity with relatively low beam currents and reduced backgrounds. The SuperB accelerator design requires a careful choice of beam parameters to reach a good trade-off between different effects. We present here simulation results for the Touschek backgrounds and lifetime obtained for both the low and high energy rings for different machine designs. A first set of horizontal collimators has been studied to stop Touschek particles. A study of the distributions of the Touschek particle losses at the interaction region into the detectors for further investigations is underway.

  4. SUPER-FOCUS: A tool for agile functional analysis of shotgun metagenomic data

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Silva, Genivaldo Gueiros Z.; Green, Kevin T.; Dutilh, Bas E.; Edwards, Robert A.

    2015-10-09

    Analyzing the functional profile of a microbial community from unannotated shotgun sequencing reads is one of the important goals in metagenomics. Functional profiling has valuable applications in biological research because it identifies the abundances of the functional genes of the organisms present in the original sample, answering the question what they can do. Currently, available tools do not scale well with increasing data volumes, which is important because both the number and lengths of the reads produced by sequencing platforms keep increasing. Here, we introduce SUPER-FOCUS, SUbsystems Profile by databasE Reduction using FOCUS, an agile homology-based approach using a reducedmore » reference database to report the subsystems present in metagenomic datasets and profile their abundances. We tested SUPER-FOCUS with over 70 real metagenomes, the results showing that it accurately predicts the subsystems present in the profiled microbial communities, and is up to 1000 times faster than other tools.« less

  5. Super-radiant backward-wave oscillators with enhanced power conversion

    SciTech Connect (OSTI)

    Rostov, V. V.; Savilov, A. V.

    2013-02-15

    We propose a method for a very significant increase of the peak power of a backward-wave electron oscillator operating in the non-stationary regime of the super-radiation of short rf pulses. This method is based on sectioning: a regular self-oscillator section is supported with a section providing amplification of the super-radiant pulse. Profiling of a resonant parameter in the amplifying section is used to avoid the parasitic self-excitation and to increase the efficiency of the electron-wave interaction. In such systems, the conversion factor (the ratio between the rf pulse power and the electron beam power) can achieve a few hundred percent.

  6. Fabrication of optical multilayer for two-color phase plate in super-resolution microscope

    SciTech Connect (OSTI)

    Iketaki, Yoshinori; Kitagawa, Katsuichi; Hidaka, Kohjiro; Kato, Naoki; Hirabayashi, Akira; Bokor, Nandor

    2014-07-15

    In super-resolution microscopy based on fluorescence depletion, the two-color phase plate (TPP) is an indispensable optical element, which can independently control the phase shifts for two beams of different color, i.e., the pump and erase beams. By controlling a phase shift of the erase beam through the TPP, the erase beam can be modulated into a doughnut shape, while the pump beam maintains the initial Gaussian shape. To obtain a reliable optical multiplayer (ML) for the TPP, we designed a ML with only two optical layers by performing numerical optimization. The measured phase shifts generated by the fabricated ML using interferometry correspond to the design values. The beam profiles in the focal plane are also consistent with theoretical results. Although the fabricated ML consists of only two optical layers, the ML can provide a suitable phase modulation function for the TPP in a practical super-resolution microscope.

  7. SuperTruck … Development and Demonstration of a Fuel-Efficient Class 8 Tractor & Trailer

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technologies 1 SuperTruck - Development and Demonstration of a Fuel Efficient Class 8 Tractor & Trailer DE-EE0003303 This presentation does not contain any proprietary, confidential, or otherwise restricted information SuperTruck - Development and Demonstration of a Fuel-Efficient Class 8 Tractor & Trailer Vehicle Systems DOE Contract: DE-EE0003303 NETL Project Manager: Ralph Nine Program Investigator : Dennis W. Jadin, Navistar DOE MERIT REVIEW WASHINGTON, D.C. May 17th, 2012 National

  8. Atomic-scale observation of parallel development of super elasticity and reversible plasticity in GaAs nanowires

    SciTech Connect (OSTI)

    Bao, Peite; Du, Sichao; Zheng, Rongkun; Wang, Yanbo; Liao, Xiaozhou; Cui, Xiangyuan; Yen, Hung-Wei; Kong Yeoh, Wai; Ringer, Simon P.; Gao, Qiang; Hoe Tan, H.; Jagadish, Chennupati; Liu, Hongwei; Zou, Jin

    2014-01-13

    We report the atomic-scale observation of parallel development of super elasticity and reversible dislocation-based plasticity from an early stage of bending deformation until fracture in GaAs nanowires. While this phenomenon is in sharp contrast to the textbook knowledge, it is expected to occur widely in nanostructures. This work indicates that the super recoverable deformation in nanomaterials is not simple elastic or reversible plastic deformation in nature, but the coupling of both.

  9. Space-Charge Effects in the Super B-Factory LER

    SciTech Connect (OSTI)

    Venturini, Marco

    2007-01-31

    Space-charge effects in the low-energy ring of the proposedSuper-B Factory are studied using a weak-strong model of dynamics asimplemented in the code Marylie/Impact (MLI). The impact of space chargeappears noticeable but our results suggest the existence of workableregions of the tune space where the design emittance is minimallyaffected. However, additional studies are recommended to fullysubstantiate this conclusion.

  10. Increasing Biofuel Deployment and Utilization through Development of Renewable Super Premium: Infrastructure Assessment

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    Increasing Biofuel Deployment and Utilization through Development of Renewable Super Premium: Infrastructure Assessment K. Moriarty National Renewable Energy Laboratory M. Kass and T. Theiss Oak Ridge National Laboratory Technical Report NREL/TP-5400-61684 November 2014 NREL is a national laboratory of the U.S. Department of Energy Office of Energy Efficiency & Renewable Energy Operated by the Alliance for Sustainable Energy, LLC This report is available at no cost from the National

  11. High-Efficiency Retrofit Lessons for Retail from a SuperTarget: Preprint

    SciTech Connect (OSTI)

    Langner, R.; Deru, M.; Hirsch, A.; Williams, S.

    2013-02-01

    The National Renewable Energy Laboratory partnered with Target under the Commercial Building Program to design and implement a retrofit of a SuperTarget in Thornton, CO. The result was a retrofit design that predicted 37% energy savings over ASHRAE Standard 90.1-2004, and 29% compared to existing (pre-retrofit) store consumption. The largest savings came from energy efficient lighting, energy efficient cooling systems, improved refrigeration, and better control of plug loads.

  12. A new high nitrogen super austenitic stainless steel with improved structure stability and corrosion resistance properties

    SciTech Connect (OSTI)

    Gagnepain, J.C.; Charles, J.; Coudreuse, L.; Bonnefois, B.

    1996-11-01

    A new highly alloyed (Cr, Mo, W, N) super austenitic grade has been developed. This grade offers high mechanical properties combined with excellent corrosion resistance in chloride acid media. This grade is particularly designed for applications in chloride, oxidizing acid media encountered in the chemical, transportation, pollution control, offshore and pulp and paper industries. Mechanical properties, corrosion resistance and weldability of this grade are presented and compared to that of other stainless steels and nickel base alloys.

  13. Highly Selective Membranes For The Separation Of Organic Vapors Using Super-Glassy Polymers

    DOE Patents [OSTI]

    Pinnau, Ingo; Lokhandwala, Kaaeid; Nguyen, Phuong; Segelke, Scott

    1997-11-18

    A process for separating hydrocarbon gases of low boiling point, particularly methane, ethane and ethylene, from nitrogen. The process is performed using a membrane made from a super-glassy material. The gases to be separated are mixed with a condensable gas, such as a C.sub.3+ hydrocarbon. In the presence of the condensable gas, improved selectivity for the low-boiling-point hydrocarbon gas over nitrogen is achieved.

  14. Method of Preparing Super-Concentrated Jets From Dense Aerosol Suspensions

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ----- Inventor(s): Michael J. Hay, Ernest J. Valeo, and Nathaniel J. Fisch | Princeton Plasma Physics Lab Method of Preparing Super-Concentrated Jets From Dense Aerosol Suspensions ----- Inventor(s): Michael J. Hay, Ernest J. Valeo, and Nathaniel J. Fisch This is improvement in aerodynamic focusing of dilute aerosol suspensions. All previous work on this subject has ignored the effect of the particle inertia in the design of the focusing nozzle. This Invention describes a nozzle design that

  15. HIGH ENERGY PULSED POWER SYSTEM FOR AGS SUPER NEUTRINO FOCUSING HORN.

    SciTech Connect (OSTI)

    ZHANG, S.Y.; SANDBERG, J.; WENG, W.-T.

    2005-05-16

    This paper present a preliminary design of a 300 kA, 2.5 Hz pulsed power system. This system will drive the focusing horn of proposed Brookhaven AGS Neutrino Super Beam Facility for Very Long Baseline Neutrino Oscillation Experiment. The peak output power of the horn pulsed power system will reach Giga-watts, and the upgraded AGS will be capable of delivering 1 MW in beam power.

  16. SuperTruck … Development and Demonstration of a Fuel-Efficient Class 8

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Tractor & Trailer | Department of Energy 1 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program Annual Merit Review and Peer Evaluation vss064_jadin_2011_o.pdf (1020.57 KB) More Documents & Publications SuperTruck … Development and Demonstration of a Fuel-Efficient Class 8 Tractor & Trailer Supertruck - Development and Demonstration of a Fuel-Efficient Class 8 Tractor & Trailer Supertruck - Development and Demonstration of a Fuel-Efficient Class 8 Tractor

  17. Experimental Ion Exchange Column With SuperLig 639 And Simulant Formulation

    SciTech Connect (OSTI)

    Morse, Megan; Nash, C.

    2013-08-26

    SuperLig639 ion exchange resin was tested as a retrieval mechanism for pertechnetate, through decontamination of a perrhenate spiked 5M Simple Average Na{sup +} Mass Based Simulant. Testing included batch contacts and a three-column ion exchange campaign. A decontamination of perrhenate exceeding 99% from the liquid feed was demonstrated. Analysis of the first formulation of a SBS/WESP simulant found unexpectedly low concentrations of soluble aluminum. Follow-on work will complete the formulation.

  18. Princeton and PPPL projects selected to run on super-powerful computer to

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    be delivered to Oak Ridge Leadership Computing Facility | Princeton Plasma Physics Lab Princeton and PPPL projects selected to run on super-powerful computer to be delivered to Oak Ridge Leadership Computing Facility By John Greenwald June 1, 2015 Tweet Widget Google Plus One Share on Facebook Computer simulation and visualization of edge turbulence in a fusion plasma. (Simulation: Seung-Hoe Ku/PPPL. Visualization: David Pugmire/ORNL) Computer simulation and visualization of edge turbulence

  19. Princeton and PPPL projects selected to run on super-powerful computer to

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    be delivered to Oak Ridge Leadership Computing Facility | Princeton Plasma Physics Lab Princeton and PPPL projects selected to run on super-powerful computer to be delivered to Oak Ridge Leadership Computing Facility By John Greenwald June 1, 2015 Tweet Widget Google Plus One Share on Facebook Computer simulation and visualization of edge turbulence in a fusion plasma. (Simulation: Seung-Hoe Ku/PPPL. Visualization: David Pugmire/ORNL) Computer simulation and visualization of edge turbulence

  20. SOWFA Super-Controller: A High-Fidelity Tool for Evaluating Wind Plant Control Approaches

    SciTech Connect (OSTI)

    Fleming, P.; Gebraad, P.; van Wingerden, J. W.; Lee, S.; Churchfield, M.; Scholbrock, A.; Michalakes, J.; Johnson, K.; Moriarty, P.

    2013-01-01

    This paper presents a new tool for testing wind plant controllers in the Simulator for Offshore Wind Farm Applications (SOWFA). SOWFA is a high-fidelity simulator for the interaction between wind turbine dynamics and the fluid flow in a wind plant. The new super-controller testing environment in SOWFA allows for the implementation of the majority of the wind plant control strategies proposed in the literature.

  1. A Spitzer search for transits of radial velocity detected super-Earths

    SciTech Connect (OSTI)

    Kammer, J. A.; Knutson, H. A.; Desert, J.-M.; Howard, A. W.; Laughlin, G. P.; Fortney, J. J.; Deming, D.; Todorov, K. O.; Agol, E.; Burrows, A.; Showman, A. P.; Lewis, N. K.

    2014-02-01

    Unlike hot Jupiters or other gas giants, super-Earths are expected to have a wide variety of compositions, ranging from terrestrial bodies like our own to more gaseous planets like Neptune. Observations of transiting systems, which allow us to directly measure planet masses and radii and constrain atmospheric properties, are key to understanding the compositional diversity of the planets in this mass range. Although Kepler has discovered hundreds of transiting super-Earth candidates over the past 4 yr, the majority of these planets orbit stars that are too far away and too faint to allow for detailed atmospheric characterization and reliable mass estimates. Ground-based transit surveys focus on much brighter stars, but most lack the sensitivity to detect planets in this size range. One way to get around the difficulty of finding these smaller planets in transit is to start by choosing targets that are already known to host super-Earth sized bodies detected using the radial velocity (RV) technique. Here we present results from a Spitzer program to observe six of the most favorable RV-detected super-Earth systems, including HD 1461, HD 7924, HD 156668, HIP 57274, and GJ 876. We find no evidence for transits in any of their 4.5 ?m flux light curves, and place limits on the allowed transit depths and corresponding planet radii that rule out even the most dense and iron-rich compositions for these objects. We also observed HD 97658, but the observation window was based on a possible ground-based transit detection that was later ruled out; thus the window did not include the predicted time for the transit detection recently made by the Microvariability and Oscillations of Stars space telescope.

  2. Extraction Based on in situ Formation of Dithiocarbamate for Separation of Am(III) from Ln(III)

    SciTech Connect (OSTI)

    Miyashita, Sunao; Yanaga, Makoto; Okuno, Kenji; Suganuma, Hideo; Satoh, Isamu

    2007-07-01

    A new solvent extraction technique based on in situ extractant formation of dithiocarbamate derivatives was constructed for the purpose of separation of Am(III) from Ln(III). Ammonium salts of dithiocarbamate in this technique are formed during the extraction course by the reaction between secondary amines and carbon disulfide in organic phase. The effects of substituent of secondary amines against the behavior of in situ formation of dithiocarbamate and the distribution behaviors of Am(III) and Ln(III)(especially Eu(III)) into nitrobenzene phase using in situ formation of dithiocarbamate were investigated. It was revealed that amines containing substituent in {alpha} position of amine were not suited that for in situ extractant formation method. The values of separation factor of Am(III)/Eu(III) >10{sup 4} were obtained by the new method using five di-substituted amines/CS{sub 2}/nitrobenzene system. (authors)

  3. Burst wait time simulation of CALIBAN reactor at delayed super-critical state

    SciTech Connect (OSTI)

    Humbert, P.; Authier, N.; Richard, B.; Grivot, P.; Casoli, P.

    2012-07-01

    In the past, the super prompt critical wait time probability distribution was measured on CALIBAN fast burst reactor [4]. Afterwards, these experiments were simulated with a very good agreement by solving the non-extinction probability equation [5]. Recently, the burst wait time probability distribution has been measured at CEA-Valduc on CALIBAN at different delayed super-critical states [6]. However, in the delayed super-critical case the non-extinction probability does not give access to the wait time distribution. In this case it is necessary to compute the time dependent evolution of the full neutron count number probability distribution. In this paper we present the point model deterministic method used to calculate the probability distribution of the wait time before a prescribed count level taking into account prompt neutrons and delayed neutron precursors. This method is based on the solution of the time dependent adjoint Kolmogorov master equations for the number of detections using the generating function methodology [8,9,10] and inverse discrete Fourier transforms. The obtained results are then compared to the measurements and Monte-Carlo calculations based on the algorithm presented in [7]. (authors)

  4. Exploration of the Super H-mode regime on DIII-D and potential advantages for burning plasma devices

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Solomon, W. M.; Snyder, P. B.; Bortolon, A.; Burrell, K. H.; Garofalo, A. M.; Grierson, B. A.; Groebner, R. J.; Loarte, A.; Leonard, A. W.; Meneghini, O.; et al

    2016-03-25

    In a new high pedestal regime ("Super H-mode") we predicted and accessed DIII-D. Super H-mode was first achieved on DIII-D using a quiescent H-mode edge, enabling a smooth trajectory through pedestal parameter space. By exploiting Super H-mode, it has been possible to access high pedestal pressures at high normalized densities. And while elimination of Edge localized modes (ELMs) is beneficial for Super H-mode, it may not be a requirement, as recent experiments have maintained high pedestals with ELMs triggered by lithium granule injection. Simulations using TGLF for core transport and the EPED model for the pedestal find that ITER canmore » benefit from the improved performance associated with Super H-mode, with increased values of fusion power and gain possible. In similar studies demonstrate that the Super H-mode pedestal can be advantageous for a steady-state power plant, by providing a path to increasing the bootstrap current while simultaneously reducing the demands on the core physics performance.« less

  5. Sloan Digital Sky Survey III (SDSS-III), Data Release 8

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Building on the legacy of the Sloan Digital Sky Survey (SDSS) and SDSS-II, the SDSS-III Collaboration is working to map the Milky Way, search for extrasolar planets, and solve the mystery of dark energy. SDSS-III's first release, Data Release 8 (DR8), became available in the first half of 2012. DR8 contains all the images ever taken by the SDSS telescope. Together, these images make up the largest color image of the sky ever made. A version of the DR8 image is shown to the right. DR8 also includes measurements for nearly 500 million stars, galaxies, and quasars, and spectra for nearly two million. All of DR8's images, spectra, and measurements are available to anyone online. You can browse through sky images, look up data for individual objects, or search for objects anywhere using any criteria. SDSS-III will collect data from 2008 to 2014, using the 2.5-meter telescope at Apache Point Observatory. SDSS-III consists of four surveys, each focused on a different scientific theme. These four surveys are: 1) Baryon Oscillation Spectroscopic Survey (BOSS); 2) SEGUE-2 (Sloan Extension for Galactic Understanding and Exploration); 3) The APO Galactic Evolution Experiment (APOGEE); and 4) The Multi-object APO Radial Velocity Exoplanet Large-area Survey (MARVELS). [Copied with edits from http://www.sdss3.org/index.php

  6. Title III of the Defense Production Act | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Title III of the Defense Production Act Title III of the Defense Production Act Matthew Seaford presentation on Title III of the Defense Production Act at the Industry Roundtable. 2_seaford_roundtable.pdf (1.21 MB) More Documents & Publications A National Strategic Plan For Advanced Manufacturing Market Drivers for Biofuels Networking and Information Technology Research and Development Supplement to the President's Budget (February 2010)

  7. Neptunium Binding Kinetics with Arsenazo(III)

    SciTech Connect (OSTI)

    Leigh R. Martin; Aaron T. Johnson; Stephen P. Mezyk

    2014-08-01

    This document has been prepared to meet FCR&D level 2 milestone M2FT-14IN0304021, Report on the results of actinide binding kinetics with aqueous phase complexants This work was carried out under the auspices of the Thermodynamics and Kinetics of Advanced Separations Systems FCR&D work package. The report details kinetics experiments that were performed to measure rates of aqueous phase complexation for pentavalent neptunium with the chromotropic dye Arsenazo III (AAIII). The studies performed were designed to determine how pH, ionic strength and AAIII concentration may affect the rate of the reaction. A brief comparison with hexavalent neptunium is also made. It was identified that as pH was increased the rate of reaction also increased, however increasing the ionic strength and concentration of AAIII had the opposite effect. Interestingly, the rate of reaction of Np(VI) with AAIII was found to be slower than that of the Np(V) reaction.

  8. Chena Hot Springs GRED III Project: Final Report Geology, Petrology...

    Open Energy Info (EERE)

    Springs GRED III Project: Final Report Geology, Petrology, Geochemistry, Hydrothermal Alteration, and Fluid Analyses Jump to: navigation, search OpenEI Reference LibraryAdd to...

  9. III-Nitride Nanowires: Emerging Materials for Lighting and Energy...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    III-Nitride Nanowires: Emerging Materials for Lighting and Energy Applications March 20, ... Wang is a Challenge Leader in the Solid State Lighting Science Energy Frontier Research ...

  10. Interfacial Chemistry of III-V Semiconductors for Photoelectrochemical...

    Office of Scientific and Technical Information (OSTI)

    Photoelectrochemical Water Splitting Citation Details In-Document Search Title: Interfacial Chemistry of III-V Semiconductors for Photoelectrochemical Water Splitting Authors: ...

  11. The coyote universe III: simulation suite and precision emulator...

    Office of Scientific and Technical Information (OSTI)

    simulation suite and precision emulator for the nonlinear matter power spectrum Citation Details In-Document Search Title: The coyote universe III: simulation suite and ...

  12. Dr. Calvin O. Butts, III | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Calvin O. Butts, III About Us Dr. Calvin O. Butts, III - President, State University of New York (SUNY) College at Old Westbury Dr. Calvin O. Butts, III Dr. Calvin O. Butts, III, is President of State University of New York, College at Old Westbury and Pastor of the renowned Abyssinian Baptist Church in New York City. Regularly sought by leaders in politics, business, and the media for his insight and opinions, he has had a pervasive impact across his career on such wide-ranging issues as

  13. Interfacial Chemistry of III-V Semiconductors for Photoelectrochemical...

    Office of Scientific and Technical Information (OSTI)

    Photoelectrochemical Water Splitting Citation Details In-Document Search Title: Interfacial Chemistry of III-V Semiconductors for Photoelectrochemical Water Splitting You are ...

  14. SDSS-III: Massive Spectroscopic Surveys of the Distant Universe...

    Office of Scientific and Technical Information (OSTI)

    Massive Spectroscopic Surveys of the Distant Universe, the Milky Way Galaxy, and Extra-Solar Planetary Systems Citation Details In-Document Search Title: SDSS-III: Massive...

  15. NEPA Implementation Procedures: Appendices I, II, and III | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Implementation Procedures: Appendices I, II, and III NEPA Implementation Procedures: ... agency compliance with the National Environmental Policy Act and the CEQ's regulations. ...

  16. On the origin of super-hot electrons from intense laser interactions with solid targets having moderate scale length preformed plasmas

    SciTech Connect (OSTI)

    Krygier, A. G.; Schumacher, D. W.; Freeman, R. R.

    2014-02-15

    We use particle-in-cell modeling to identify the acceleration mechanism responsible for the observed generation of super-hot electrons in ultra-intense laser-plasma interactions with solid targets with pre-formed plasma. We identify several features of direct laser acceleration that drive the generation of super-hot electrons. We find that, in this regime, electrons that become super-hot are primarily injected by a looping mechanism that we call loop-injected direct acceleration.

  17. Water cycling between ocean and mantle: Super-earths need not be waterworlds

    SciTech Connect (OSTI)

    Cowan, Nicolas B.; Abbot, Dorian S.

    2014-01-20

    Large terrestrial planets are expected to have muted topography and deep oceans, implying that most super-Earths should be entirely covered in water, so-called waterworlds. This is important because waterworlds lack a silicate weathering thermostat so their climate is predicted to be less stable than that of planets with exposed continents. In other words, the continuously habitable zone for waterworlds is much narrower than for Earth-like planets. A planet's water is partitioned, however, between a surface reservoir, the ocean, and an interior reservoir, the mantle. Plate tectonics transports water between these reservoirs on geological timescales. Degassing of melt at mid-ocean ridges and serpentinization of oceanic crust depend negatively and positively on seafloor pressure, respectively, providing a stabilizing feedback on long-term ocean volume. Motivated by Earth's approximately steady-state deep water cycle, we develop a two-box model of the hydrosphere and derive steady-state solutions to the water partitioning on terrestrial planets. Critically, hydrostatic seafloor pressure is proportional to surface gravity, so super-Earths with a deep water cycle will tend to store more water in the mantle. We conclude that a tectonically active terrestrial planet of any mass can maintain exposed continents if its water mass fraction is less than ∼0.2%, dramatically increasing the odds that super-Earths are habitable. The greatest source of uncertainty in our study is Earth's current mantle water inventory: the greater its value, the more robust planets are to inundation. Lastly, we discuss how future missions can test our hypothesis by mapping the oceans and continents of massive terrestrial planets.

  18. Super-Grid Modeling of the Elastic Wave Equation in Semi-Bounded Domains

    SciTech Connect (OSTI)

    Petersson, N. Anders; Sjögreen, Björn

    2014-10-01

    Abstract

    We develop a super-grid modeling technique for solving the elastic wave equation in semi-bounded two- and three-dimensional spatial domains. In this method, waves are slowed down and dissipated in sponge layers near the far-field boundaries. Mathematically, this is equivalent to a coordinate mapping that transforms a very large physical domain to a significantly smaller computational domain, where the elastic wave equation is solved numerically on a regular grid. To damp out waves that become poorly resolved because of the coordinate mapping, a high order artificial dissipation operator is added in layers near the boundaries of the computational domain. We prove by energy estimates that the super-grid modeling leads to a stable numerical method with decreasing energy, which is valid for heterogeneous material properties and a free surface boundary condition on one side of the domain. Our spatial discretization is based on a fourth order accurate finite difference method, which satisfies the principle of summation by parts. We show that the discrete energy estimate holds also when a centered finite difference stencil is combined with homogeneous Dirichlet conditions at several ghost points outside of the far-field boundaries. Therefore, the coefficients in the finite difference stencils need only be boundary modified near the free surface. This allows for improved computational efficiency and significant simplifications of the implementation of the proposed method in multi-dimensional domains. Numerical experiments in three space dimensions show that the modeling error from truncating the domain can be made very small by choosing a sufficiently wide super-grid damping layer. The numerical accuracy is first evaluated against analytical solutions of Lamb’s problem, where fourth order accuracy is observed with a sixth order artificial dissipation. We then use successive grid refinements to study the numerical accuracy in the more

  19. A plausible (overlooked) super-luminous supernova in the Sloan digital sky survey stripe 82 data

    SciTech Connect (OSTI)

    Kostrzewa-Rutkowska, Zuzanna; Koz?owski, Szymon; Wyrzykowski, ?ukasz; Djorgovski, S. George; Mahabal, Ashish A.; Glikman, Eilat; Koposov, Sergey E-mail: simkoz@astrouw.edu.pl

    2013-12-01

    We present the discovery of a plausible super-luminous supernova (SLSN), found in the archival data of Sloan Digital Sky Survey (SDSS) Stripe 82, called PSN 000123+000504. The supernova (SN) peaked at m {sub g} < 19.4 mag in the second half of 2005 September, but was missed by the real-time SN hunt. The observed part of the light curve (17 epochs) showed that the rise to the maximum took over 30 days, while the decline time lasted at least 70 days (observed frame), closely resembling other SLSNe of SN 2007bi type. The spectrum of the host galaxy reveals a redshift of z = 0.281 and the distance modulus of ? = 40.77 mag. Combining this information with the SDSS photometry, we found the host galaxy to be an LMC-like irregular dwarf galaxy with an absolute magnitude of M{sub B} = 18.2 0.2 mag and an oxygen abundance of 12+log?[O/H]=8.30.2; hence, the SN peaked at M {sub g} < 21.3 mag. Our SLSN follows the relation for the most energetic/super-luminous SNe exploding in low-metallicity environments, but we found no clear evidence for SLSNe to explode in low-luminosity (dwarf) galaxies only. The available information on the PSN 000123+000504 light curve suggests the magnetar-powered model as a likely scenario of this event. This SLSN is a new addition to a quickly growing family of super-luminous SNe.

  20. A SUPER-EDDINGTON WIND SCENARIO FOR THE PROGENITORS OF TYPE Ia SUPERNOVAE

    SciTech Connect (OSTI)

    Ma, Xin; Chen, Xuefei; Chen, Hai-liang; Han, Zhanwen; Denissenkov, Pavel A. E-mail: cxf@ynao.ac.cn

    2013-12-01

    The accretion of hydrogen-rich material on to carbon-oxygen white dwarfs (CO WDs) is crucial for understanding Type Ia supernova (SN Ia) from the single-degenerate model, but this process has not been well understood due to the numerical difficulties in treating H and He flashes during the accretion. For CO WD masses from 0.5 to 1.378 M {sub ?} and accretion rates in the range from 10{sup 8} to 10{sup 5} M {sub ?} yr{sup 1}, we simulated the accretion of solar-composition material on to CO WDs using the state-of-the-art stellar evolution code of MESA. For comparison with steady-state models, we first ignored the contribution from nuclear burning to the luminosity when determining the Eddington accretion rate, and found that the properties of H burning in our accreting CO WD models are similar to those from the steady-state models, except that the critical accretion rates at which the WDs turn into red giants or H-shell flashes occur on their surfaces are slightly higher than those from the steady-state models. However, the super-Eddington wind is triggered at much lower accretion rates than previously thought, when the contribution of nuclear burning to the total luminosity is included. This super-Eddington wind naturally prevents the CO WDs with high accretion rates from becoming red giants, thus presenting an alternative to the optically thick wind proposed by Hachisu etal. Furthermore, the super-Eddington wind works in low-metallicity environments, which may explain SNe Ia observed at high redshifts.

  1. Hubble space telescope near-ir transmission spectroscopy of the super-Earth HD 97658B

    SciTech Connect (OSTI)

    Knutson, Heather A.; Dragomir, Diana; Kreidberg, Laura; Bean, Jacob L.; Kempton, Eliza M.-R.; McCullough, P. R.; Fortney, Jonathan J.; Gillon, Michael; Homeier, Derek; Howard, Andrew W.

    2014-10-20

    Recent results from the Kepler mission indicate that super-Earths (planets with masses between 1-10 times that of the Earth) are the most common kind of planet around nearby Sun-like stars. These planets have no direct solar system analogue, and are currently one of the least well-understood classes of extrasolar planets. Many super-Earths have average densities that are consistent with a broad range of bulk compositions, including both water-dominated worlds and rocky planets covered by a thick hydrogen and helium atmosphere. Measurements of the transmission spectra of these planets offer the opportunity to resolve this degeneracy by directly constraining the scale heights and corresponding mean molecular weights of their atmospheres. We present Hubble Space Telescope near-infrared spectroscopy of two transits of the newly discovered transiting super-Earth HD 97658b. We use the Wide Field Camera 3's (WFC3) scanning mode to measure the wavelength-dependent transit depth in 30 individual bandpasses. Our averaged differential transmission spectrum has a median 1? uncertainty of 23 ppm in individual bins, making this the most precise observation of an exoplanetary transmission spectrum obtained with WFC3 to date. Our data are inconsistent with a cloud-free solar metallicity atmosphere at the 10? level. They are consistent at the 0.4? level with a flat line model, as well as effectively flat models corresponding to a metal-rich atmosphere or a solar metallicity atmosphere with a cloud or haze layer located at pressures of 10 mbar or higher.

  2. CONVERSION EXTRACTION DESULFURIZATION (CED) PHASE III

    SciTech Connect (OSTI)

    James Boltz

    2005-03-01

    This project was undertaken to refine the Conversion Extraction Desulfurization (CED) technology to efficiently and economically remove sulfur from diesel fuel to levels below 15-ppm. CED is considered a generic term covering all desulfurization processes that involve oxidation and extraction. The CED process first extracts a fraction of the sulfur from the diesel, then selectively oxidizes the remaining sulfur compounds, and finally extracts these oxidized materials. The Department of Energy (DOE) awarded Petro Star Inc. a contract to fund Phase III of the CED process development. Phase III consisted of testing a continuous-flow process, optimization of the process steps, design of a pilot plant, and completion of a market study for licensing the process. Petro Star and the Degussa Corporation in coordination with Koch Modular Process Systems (KMPS) tested six key process steps in a 7.6-centimeter (cm) (3.0-inch) inside diameter (ID) column at gas oil feed rates of 7.8 to 93.3 liters per hour (l/h) (2.1 to 24.6 gallons per hour). The team verified the technical feasibility with respect to hydraulics for each unit operation tested and successfully demonstrated pre-extraction and solvent recovery distillation. Test operations conducted at KMPS demonstrated that the oxidation reaction converted a maximum of 97% of the thiophenes. The CED Process Development Team demonstrated that CED technology is capable of reducing the sulfur content of light atmospheric gas oil from 5,000-ppm to less than 15-ppm within the laboratory scale. In continuous flow trials, the CED process consistently produced fuel with approximately 20-ppm of sulfur. The process economics study calculated an estimated process cost of $5.70 per product barrel. The Kline Company performed a marketing study to evaluate the possibility of licensing the CED technology. Kline concluded that only 13 refineries harbored opportunity for the CED process. The Kline study and the research team's discussions with

  3. Ultrafast spectroscopy of super high frequency mechanical modes of doubly clamped beams

    SciTech Connect (OSTI)

    Ristow, Oliver; Merklein, Moritz; Grossmann, Martin; Hettich, Mike; Schubert, Martin; Bruchhausen, Axel; Scheer, Elke; Dekorsy, Thomas; Barretto, Elaine C. S.; Grebing, Jochen; Erbe, Artur; Mounier, Denis; Gusev, Vitalyi

    2013-12-02

    We use ultrafast pump-probe spectroscopy to study the mechanical vibrations in the time domain of doubly clamped silicon nitride beams. Beams with two different clamping conditions are investigated. Finite element method calculations are performed to analyse the mode spectra of both structures. By calculating the strain integral on the surface of the resonators, we are able to reproduce the effect of the detection mechanism and identify all the measured modes. We show that our spectroscopy technique combined with our modelling tools allow the investigation of several different modes in the super high frequency range (3-30?GHz) and above, bringing more information about the vibration modes of nanomechanical resonators.

  4. Development of the SSC (Superconducting Super Collider) trim coil beam tube assembly

    SciTech Connect (OSTI)

    Skaritka, J.; Kelly, E.; Schneider, W.; Shutt, R.; Thompson, P.; Wanderer, P.; Willen, E.; Bintinger, D.; Coluccio, R.; Schieber, L.

    1987-01-01

    The Superconducting Super Collider uses approx. =9600 dipole magnets. The magnets have been carefully designed to exhibit minimal magnetic field harmonics. However, because of superconductor magnetization effects, iron saturation and conductor/coil positioning errors, certain harmonic errors are possible and must be corrected by use of multipole correctors called trim coils. For the most efficient use of axial space in the magnet, and lowest possible current, a distributed internal correction coil design is planned. The trim coil assembly is secured to the beam tube, a uhv tube with special strength, size, conductivity and vacuum. The report details the SSC trim coil/beam tube assembly specifications, history, and ongoing development.

  5. Qualification of welded super 13%Cr martensitic stainless steels for sour service applications

    SciTech Connect (OSTI)

    Enerhaug, J.; Eliassen, S.L.; Kvaale, P.E.

    1997-08-01

    A test program has been carried out to qualify welded super 13%Cr stainless steels for sour service applications. The test program included weldability trials, weld simulations, mechanical testing and corrosion testing of 13%Cr steels from five different steel mills. Two of the tested steels have been qualified for use as flowline materials in some parts of new sour service fields. The result shows excellent weldability properties and acceptable corrosion properties. Post weld heat treatment (PWHT) of the welds improved the resistance towards sulfide stress corrosion cracking significantly.

  6. 'Exotic' material is like a switch when super thin > Archived News Stories

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    > The Energy Materials Center at Cornell 'Exotic' material is like a switch when super thin April 17th, 2014 › By Anne Ju Hanfei Wei An artist's rendering of the thickness-driven, metal-insulator transition in sub-nanometer films of a lanthanum nickelate. Nickel atoms are shown in gold, oxygen atoms in white, and lanthanum atoms in red, and metallicity is achieved in going from two to three atomic layers. Ever-shrinking electronic devices could get down to atomic dimensions with the

  7. The Super Efficient Refrigerator Program: Case study of a Golden Carrot program

    SciTech Connect (OSTI)

    Eckert, J B

    1995-07-01

    The work in this report was conducted by the Analytic Studies Division (ASD) of the National Renewable Energy Laboratory (NREL) for the U.S. Department of Energy Office of Energy Efficiency and Renewable Energy, Office of Building Technologies. This case study describes the development and implementation of the Super Efficient Refrigerator Program (SERP), which awarded $30 million to the refrigerator manufacturer that developed and commercialized a refrigerator that exceeded 1993 federal efficiency standards by at least 25%. The program was funded by 24 public and private utilities. As the first Golden Carrot program to be implemented in the United States, SERP was studied as an example for future `market-pull` efforts.

  8. Spectral Modeling of Scintillator for the NEMO-3 and SuperNEMO Detectors

    SciTech Connect (OSTI)

    A. J. Caffrey; J. J. Horkley

    2011-01-01

    We have constructed a GEANT4-based detailed softwaremodel of photon transport in plastic scintillator blocks and have used it to study the NEMO-3 and SuperNEMO calorimeters employed in experiments designed to search for neutrinoless double beta decay. We compare our simulations to measurements using conversion electrons from a calibration source of 207Bi and show that the agreement is improved if wavelength-dependent properties of the calorimeter are taken into account. In this article, we briefly describe our modeling approach and results of our studies.

  9. Thermal conductance measurements of bolted copper joints for SuperCDMS

    SciTech Connect (OSTI)

    Schmitt, R. L.; Tatkowski, G; Ruschman, M.; Golwala, S.; Kellaris, N.; Daal, M.; Hall, J.; Hoppe, E. W.

    2015-05-22

    Joint thermal conductance testing has been undertaken for bolted copper to copper connections from 60 mK to 26 K. This testing was performed to validate an initial design basis for the SuperCDMS experiment, where a dilution refrigerator will be coupled to a cryostat via multiple bolted connections. Copper used during testing was either gold plated or passivated with citric acid to prevent surface oxidation. Results obtained are well fit by a power law regression of joint thermal conductance to temperature and match well with data collected during a literature review.

  10. Super Bowl City Leads on Energy Efficient Forefront | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Bowl City Leads on Energy Efficient Forefront Super Bowl City Leads on Energy Efficient Forefront February 2, 2013 - 11:30am Addthis New Orleans' Mercedes-Benz Superdome features more than 26,000 LED lights on the building's exterior. The system uses only 10 kilowatts of electricity, equivalent to powering a small home. | Photo courtesy of SMG. New Orleans' Mercedes-Benz Superdome features more than 26,000 LED lights on the building's exterior. The system uses only 10 kilowatts of electricity,

  11. Final Report - The Decline and Fall of the Superconducting Super Collider

    SciTech Connect (OSTI)

    RIORDAN, MICHAEL

    2011-11-29

    In October 1993 the US Congress terminated the Superconducting Super Collider — at the time the largest pure-science project ever attempted, with a total cost estimated to exceed $10 billion. It was a stunning loss for the US highenergy physics community, which until that moment had perched for decades at the pinnacle of American science. Ever since 1993, this once-dominant scientific community has been in gradual decline. With the 2010 startup of research on the CERN Large Hadron Collider and the 2011 shutdown of the Fermilab Tevatron, world leadership in elementary-particle physics has crossed the Atlantic and returned to Europe.

  12. HOM Calculations of New RF Cavities for Super B-Factory

    SciTech Connect (OSTI)

    Novokhatski, A.

    2004-11-01

    High average HOM power generated by beams in a vacuum chamber of electron-positron colliders can limit achievement of high currents. It is of great concern for future super B-factories of very high luminosity, obtained from high beam current and short bunch length. We can minimize the HOM power by choosing the right RF cavity shape. Here we present results of computer spectrum analyses of different kind of cavities, which are already used or can be used in B-factories.

  13. Gluon scattering in N=4 super-Yang-Mills theory fromweak to strong coupling

    SciTech Connect (OSTI)

    Dixon, Lance J.; /SLAC

    2008-03-25

    I describe some recent developments in the understanding of gluon scattering amplitudes in N = 4 super-Yang-Mills theory in the large-N{sub c} limit. These amplitudes can be computed to high orders in the weak coupling expansion, and also now at strong coupling using the AdS/CFT correspondence. They hold the promise of being solvable to all orders in the gauge coupling, with the help of techniques based on integrability. They are intimately related to expectation values for polygonal Wilson loops composed of light-like segments.

  14. Classification of generalized quantum statistics associated with the exceptional Lie (super)algebras

    SciTech Connect (OSTI)

    Stoilova, N. I.; Jeugt, J. van der

    2007-04-15

    Generalized quantum statistics (GQS) associated with a Lie algebra or Lie superalgebra extends the notion of para-Bose or para-Fermi statistics. Such GQS have been classified for all classical simple Lie algebras and basic classical Lie superalgebras. In the current paper we finalize this classification for all exceptional Lie algebras and superalgebras. Since the definition of GQS is closely related to a certain Z grading of the Lie (super)algebra G, our classification reproduces some known Z gradings of exceptional Lie algebras. For exceptional Lie superalgebras such a classification of Z gradings has not been given before.

  15. Structural performance of the first SSC (Superconducting Super Collider) Design B dipole magnet

    SciTech Connect (OSTI)

    Nicol, T.H.

    1989-09-01

    The first Design B Superconducting Super Collider (SSC) dipole magnet has been successfully tested. This magnet was heavily instrumented with temperature and strain gage sensors in order to evaluate its adherence to design constraints and design calculations. The instrumentation and associated data acquisition system allowed monitoring of the magnet during cooldown, warmup, and quench testing. This paper will focus on the results obtained from structural measurements on the suspension system during normal and rapid cooldowns and during quench studies at full magnet current. 4 refs., 9 figs.

  16. Thermal conductance measurements of bolted copper joints for SuperCDMS

    SciTech Connect (OSTI)

    Schmitt, R.; Tatkowski, Greg; Ruschman, M.; Golwala, S. R.; Kellaris, N.; Daal, M.; Hall, Jeter C.; Hoppe, Eric W.

    2015-09-01

    Joint thermal conductance testing has been undertaken for bolted copper to copper connections from 60 mK to 26 K. This testing was performed to validate an initial design basis for the SuperCDMS experiment, where a dilution refrigerator will be coupled to a cryostat via multiple bolted connections. Copper used during testing was either gold plated or passivated with citric acid to prevent surface oxidation. Results obtained are well fit by a power law regression of joint thermal conductance to temperature and match well with data collected during a literature review.

  17. Coordinate-Space Hartree-Fock-Bogoliubov Solvers for Super fluid Fermi

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Systems in Large Boxes | Argonne Leadership Computing Facility Coordinate-Space Hartree-Fock-Bogoliubov Solvers for Super fluid Fermi Systems in Large Boxes Authors: Pei, J.C., Fann, G.I., Harrison, R.J., Nazarewicz, W., Hill, J., Galindo, D., Jia, J. The self-consistent Hartree-Fock-Bogoliubov problem in large boxes can be solved accurately in the coordinate space with the recently developed solvers HFB-AX (2D) and MADNESS-HFB (3D). This is essential for the description of superfluid Fermi

  18. Random matrix theory for mixed regular-chaotic dynamics in the super-extensive regime

    SciTech Connect (OSTI)

    El-Hady, A. Abd; Abul-Magd, A. Y.

    2011-10-27

    We apply Tsallis's q-indexed nonextensive entropy to formulate a random matrix theory (RMT), which may be suitable for systems with mixed regular-chaotic dynamics. We consider the super-extensive regime of q<1. We obtain analytical expressions for the level-spacing distributions, which are strictly valid for 2 X2 random-matrix ensembles, as usually done in the standard RMT. We compare the results with spacing distributions, numerically calculated for random matrix ensembles describing a harmonic oscillator perturbed by Gaussian orthogonal and unitary ensembles.

  19. Magnetic Fields in Population III Star Formation

    SciTech Connect (OSTI)

    Turk, Matthew J.; Oishi, Jeffrey S.; Abel, Tom; Bryan, Greg

    2012-02-22

    We study the buildup of magnetic fields during the formation of Population III star-forming regions, by conducting cosmological simulations from realistic initial conditions and varying the Jeans resolution. To investigate this in detail, we start simulations from identical initial conditions, mandating 16, 32 and 64 zones per Jeans length, and studied the variation in their magnetic field amplification. We find that, while compression results in some amplification, turbulent velocity fluctuations driven by the collapse can further amplify an initially weak seed field via dynamo action, provided there is sufficient numerical resolution to capture vortical motions (we find this requirement to be 64 zones per Jeans length, slightly larger than, but consistent with previous work run with more idealized collapse scenarios). We explore saturation of amplification of the magnetic field, which could potentially become dynamically important in subsequent, fully-resolved calculations. We have also identified a relatively surprising phenomena that is purely hydrodynamic: the higher-resolved simulations possess substantially different characteristics, including higher infall-velocity, increased temperatures inside 1000 AU, and decreased molecular hydrogen content in the innermost region. Furthermore, we find that disk formation is suppressed in higher-resolution calculations, at least at the times that we can follow the calculation. We discuss the effect this may have on the buildup of disks over the accretion history of the first clump to form as well as the potential for gravitational instabilities to develop and induce fragmentation.

  20. MIGRATION AND GROWTH OF PROTOPLANETARY EMBRYOS. II. EMERGENCE OF PROTO-GAS-GIANT CORES VERSUS SUPER EARTH PROGENITORS

    SciTech Connect (OSTI)

    Liu, Beibei; Zhang, Xiaojia; Lin, Douglas N. C.; Aarseth, Sverre J.

    2015-01-01

    Nearly 15%-20% of solar type stars contain one or more gas giant planets. According to the core-accretion scenario, the acquisition of their gaseous envelope must be preceded by the formation of super-critical cores with masses 10times or larger than that of the Earth. It is natural to link the formation probability of gas giant planets with the supply of gases and solids in their natal disks. However, a much richer population of super Earths suggests that (1) there is no shortage of planetary building block material, (2) a gas giant's growth barrier is probably associated with whether it can merge into super-critical cores, and (3) super Earths are probably failed cores that did not attain sufficient mass to initiate efficient accretion of gas before it is severely depleted. Here we construct a model based on the hypothesis that protoplanetary embryos migrated extensively before they were assembled into bona fide planets. We construct a Hermite-Embryo code based on a unified viscous-irradiation disk model and a prescription for the embryo-disk tidal interaction. This code is used to simulate the convergent migration of embryos, and their close encounters and coagulation. Around the progenitors of solar-type stars, the progenitor super-critical-mass cores of gas giant planets primarily form in protostellar disks with relatively high (? 10{sup 7} M {sub ?} yr{sup 1}) mass accretion rates, whereas systems of super Earths (failed cores) are more likely to emerge out of natal disks with modest mass accretion rates, due to the mean motion resonance barrier and retention efficiency.

  1. The SuperB Project: Accelerator Status and R&D

    SciTech Connect (OSTI)

    Biagini, M.E.; Boni, R.; Boscolo, M.; Buonomo, B.; Demma, T.; Drago, A.; Guiducci, S.; Liuzzo, S.; Mazzitelli, G.; Pellegrino, L.; Preger, M.A.; Raimondi, P.; Ricci, R.; Rotundo, U.; Sanelli, C.; Stecchi, A.; Serio, M.; Stella, A.; Tomassini, S.; Zobov, M.; Bini, S.; /Frascati /Orsay, LAL /SLAC /Novosibirsk, IYF /Pisa U. /INFN, Pisa /INFN, Pisa /Pisa U. /Orsay, LAL /Annecy, LAPP /LPSC, Grenoble /DAPNIA, Saclay /PSI, Villigen /CERN /Beijing, Inst. High Energy Phys.

    2012-04-27

    The SuperB collider project has been recently approved by the Italian Government as part of the National Research Plan. SuperB is a high luminosity (10{sup 36} cm{sup -2} s{sup -1}) asymmetric e{sup +}e{sup -} collider at the {Upsilon}(4S) energy. The design is based on a 'large Piwinski angle and Crab Waist' scheme already successfully tested at the DAPHNE {Phi}-Factory in Frascati, Italy. The project combines the challenges of high luminosity colliders and state-of-the-art synchrotron light sources, such as two beams (e{sup +} at 6.7, HER, and e{sup -} at 4.2 GeV, LER) with extremely low emittances and small beam sizes at the Interaction Point. As unique features, the electron beam will be longitudinally polarized at the IP and the rings will be able to ramp down to collide at the {tau}/charm energy threshold with a luminosity of 10{sup 35} cm{sup -2} s{sup -1}. The relatively low beam currents (about 2 A) will allow for low running (power) costs compared to similar machines. The insertion of beam lines for synchrotron radiation (SR) users is the latest feature included in the design. The lattice has been recently modified to accommodate insertion devices for X-rays production.

  2. Welding and weldability of directionally solidified single crystal nickel-base super-alloys

    SciTech Connect (OSTI)

    vitek, j.m.

    1996-09-01

    The objective of this CRADA project was to investigate the weldability of polycrystalline, directionally-solidified, and single-crystal, nickel-base super-alloys. These materials are used extensively in turbine engine components. The ability to weld these materials is highly desirable in that it would greatly facilitate component fabrication. Welding of these materials would also have the potential benefit of allowing for the repair of cracked or worn components. Specifically, the program had four objectives: (1) to evaluate the weldability of nickel-base super-alloys; (2) to characterize the solidification microstructure of the welds; (3) to evaluate the phase stability of the weldments during exposure to service conditions; and (4) to determine the mechanical properties of the welds. Westinghouse Electric Corporation was to supply material for the program, in both as-case and heat-treated form. This was to include commercially available as well as experimental alloys developed at Westinghouse. ORNL was to perform weldability tests on the materials using a variety of welding procedures.

  3. MM-Estimator and Adjusted Super Smoother based Simultaneous Prediction Confedenc

    Energy Science and Technology Software Center (OSTI)

    2002-07-19

    A Novel Application of Regression Analysis (MM-Estimator) with Simultaneous Prediction Confidence Intervals are proposed to detect up- or down-regulated genes, which are outliers in scatter plots based on log-transformed red (Cy5 fluorescent dye) versus green (Cy3 fluorescent Dye) intensities. Advantages of the application: 1) Robust and Resistant MM-Estimator is a Reliable Method to Build Linear Regression In the presence of Outliers, 2) Exploratory Data Analysis Tools (Boxplots, Averaged Shifted Histograms, Quantile-Quantile Normal Plots and Scattermore » Plots) are Unsed to Test Visually underlying assumptions of linearity and Contaminated Normality in Microarray data), 3) Simultaneous prediction confidence intervals (SPCIs) Guarantee a desired confidence level across the whole range of the data points used for the scatter plots. Results of the outlier detection procedure is a set of significantly differentially expressed genes extracted from the employed microarray data set. A scatter plot smoother (super smoother or locally weighted regression) is used to quantify heteroscendasticity is residual variance (Commonly takes place in lower and higher intensity areas). The set of differentially expressed genes is quantified using interval estimates for P-values as a probabilistic measure of being outlier by chance. Monte Carlo simultations are used to adjust super smoother-based SPCIs.her.« less

  4. Further Progress on a Design for a Super-B Interaction Region

    SciTech Connect (OSTI)

    Sullivan, M; Bertsche, K.; Seeman, J.; Wienands, U.; Biagini, M.E.; Raimondi, P.; Paoloni, E.; Bettoni, S.; /CERN

    2009-05-20

    We present an improved design for a SuperB interaction region. The new design minimizes local bending of the two colliding beams by separating all beam magnetic elements near the Interaction Point (IP). The total crossing angle at the IP is increased from 48 mrad to 60 mrad. The first magnetic element is a six slice Permanent Magnet (PM) quadrupole with an elliptical aperture allowing us to increase the vertical space for the beam. This magnet starts 36 cm from the Interaction Point (IP). This magnet is only seen by the Low-Energy Beam (LEB), the High-Energy Beam (HEB) has a drift space at this location. This allows the preliminary focusing of the LEB which has a smaller beta y* at the IP than the HEB. The rest of the final focusing for both beams is achieved by two super-conducting side-by-side quadrupoles (QD0 and QF1). These sets of magnets are enclosed in a warm bore cryostat located behind the PM quadrupole for the LEB. We describe this design for the interaction region.

  5. Development of a super high speed motor-generator and controller

    SciTech Connect (OSTI)

    Hong, Do-Kwan Ahn, Min-Hyuk; Joo, Dae-Suk; Woo, Byung-Chul; Koo, Dae-Hyun

    2014-05-07

    To develop a super high speed motor-generator, it is essential to deal with magnetic analysis, dynamic analysis, and experimental evaluation of the heart of the MTG (Microturbine Generator) system, the motor-generator. An amorphous core is applied to a stator core for reduction of iron loss at high speed, and the motor-generator is analyzed with considerations focused on magnetic losses and the statistical optimum design. The performance of the amorphous core is validated by the analysis and experiment by back-to-back tests considering the AC load. Rotor dynamics is performed for dynamic stability at high speed using transient analysis orbit diagrams and compared with the experimental results. The simulation results of the generator are compared with the experiment. Also a super high speed controller of the MTG system is developed using a sensorless algorithm, power stack, gate driver, digital signal processing, analog circuit, and radiation heat design. Based on these results, a high speed motor-generator and controller are successfully developed.

  6. Measurement of SQUID noise levels for SuperCDMS SNOLAB detectors - Final Paper

    SciTech Connect (OSTI)

    Lee, Maxwell

    2015-08-27

    SuperCDMS SNOLAB is a second generation direct dark matter search. In the SuperCDMS SNOLAB experiment, detectors are able to pick up from signals from dark matter nuclear recoil interactions which occur inside the bulk of the detectors. These interactions produce both phonon and charge signals. HEMTs read out charge signals whereas TES are used to detect phonon signals which are then read out by SQUID amplifiers. SQUID amplifiers must add negligible noise to the TES intrinsic noise which has been previously measured and is approximately 50pA/√Hz down to 100Hz for ease of signal distinguishability in dark matter nuclear interactions. The intrinsic noise level of the SQUID was tested in the SLAC 300mK fridge and determined to provide adequately low levels of noise with a floor of approximately 3pA/√Hz. Furthermore, a 10x amplifier was tested for addition of extraneous noise. This noise was investigated with and without this amplifier, and it was found that it did not add a significant amount of noise to the intrinsic SQUID noise.

  7. Super massive black hole in galactic nuclei with tidal disruption of stars

    SciTech Connect (OSTI)

    Zhong, Shiyan; Berczik, Peter; Spurzem, Rainer

    2014-09-10

    Tidal disruption of stars by super massive central black holes from dense star clusters is modeled by high-accuracy direct N-body simulation. The time evolution of the stellar tidal disruption rate, the effect of tidal disruption on the stellar density profile, and, for the first time, the detailed origin of tidally disrupted stars are carefully examined and compared with classic papers in the field. Up to 128k particles are used in simulation to model the star cluster around a super massive black hole, and we use the particle number and the tidal radius of the black hole as free parameters for a scaling analysis. The transition from full to empty loss-cone is analyzed in our data, and the tidal disruption rate scales with the particle number, N, in the expected way for both cases. For the first time in numerical simulations (under certain conditions) we can support the concept of a critical radius of Frank and Rees, which claims that most stars are tidally accreted on highly eccentric orbits originating from regions far outside the tidal radius. Due to the consumption of stars moving on radial orbits, a velocity anisotropy is found inside the cluster. Finally we estimate the real galactic center based on our simulation results and the scaling analysis.

  8. SuperIdentity: Fusion of Identity across Real and Cyber Domains

    SciTech Connect (OSTI)

    Black, Sue; Creese, Sadie; Guest, Richard; Pike, William A.; Saxby, Steven; Stanton Fraser, Danae; Stevenage, Sarah; Whitty, Monica

    2012-04-23

    Under both benign and malign circumstances, people now manage a spectrum of identities across both real-world and cyber domains. Our belief, however, is that all these instances ultimately track back for an individual to reflect a single 'SuperIdentity'. This paper outlines the assumptions underpinning the SuperIdentity Project, describing the innovative use of data fusion to incorporate novel real-world and cyber cues into a rich framework appropriate for modern identity. The proposed combinatorial model will support a robust identification or authentication decision, with confidence indexed both by the level of trust in data provenance, and the diagnosticity of the identity factors being used. Additionally, the exploration of correlations between factors may underpin the more intelligent use of identity information so that known information may be used to predict previously hidden information. With modern living supporting the 'distribution of identity' across real and cyber domains, and with criminal elements operating in increasingly sophisticated ways in the hinterland between the two, this approach is suggested as a way forwards, and is discussed in terms of its impact on privacy, security, and the detection of threat.

  9. Analytical model for CMB temperature angular power spectrum from cosmic (super-)strings

    SciTech Connect (OSTI)

    Yamauchi, Daisuke; Yoo, Chul-Moon; Sasaki, Misao; Takahashi, Keitaro; Sendouda, Yuuiti

    2010-09-15

    We present a new analytical method to calculate the small angle cosmic microwave background (CMB) temperature angular power spectrum due to cosmic (super-)string segments. In particular, using our method, we clarify the dependence on the intercommuting probability P. We find that the power spectrum is dominated by Poisson-distributed string segments. The power spectrum for a general value of P has a plateau on large angular scales and shows a power-law decrease on small angular scales. The resulting spectrum in the case of conventional cosmic strings is in very good agreement with the numerical result obtained by Fraisse et al.. Then we estimate the upper bound on the dimensionless tension of the string for various values of P by assuming that the fraction of the CMB power spectrum due to cosmic (super-)strings is less than ten percent at various angular scales up to l=2000. We find that the amplitude of the spectrum increases as the intercommuting probability. As a consequence, strings with smaller intercommuting probabilities are found to be more tightly constrained.

  10. Gj 832c: A super-Earth in the habitable zone

    SciTech Connect (OSTI)

    Wittenmyer, Robert A.; Horner, Jonathan; Tinney, C. G.; Marshall, J. P.; Bailey, J.; Salter, G. S.; Wright, D.; Tuomi, Mikko; Jones, H. R. A.; Butler, R. P.; Arriagada, P.; Anglada-Escudé, Guillem; Carter, B. D.; O'Toole, S. J.; Crane, J. D.; Schectman, S. A.; Thompson, I.; Minniti, D.; Jenkins, J. S.; Diaz, M.

    2014-08-20

    We report the detection of GJ 832c, a super-Earth orbiting near the inner edge of the habitable zone of GJ 832, an M dwarf previously known to host a Jupiter analog in a nearly circular 9.4 yr orbit. The combination of precise radial-velocity measurements from three telescopes reveals the presence of a planet with a period of 35.68 ± 0.03 days and minimum mass (m sin i) of 5.4 ± 1.0 Earth masses. GJ 832c moves on a low-eccentricity orbit (e = 0.18 ± 0.13) toward the inner edge of the habitable zone. However, given the large mass of the planet, it seems likely that it would possess a massive atmosphere, which may well render the planet inhospitable. Indeed, it is perhaps more likely that GJ 832c is a 'super-Venus', featuring significant greenhouse forcing. With an outer giant planet and an interior, potentially rocky planet, the GJ 832 planetary system can be thought of as a miniature version of our own solar system.

  11. GROUND-BASED TRANSIT OBSERVATIONS OF THE SUPER-EARTH 55 Cnc e

    SciTech Connect (OSTI)

    De Mooij, E. J. W.; Lpez-Morales, M.; Karjalainen, R.; Hrudkova, M.; Jayawardhana, Ray

    2014-12-20

    We report the first ground-based detections of the shallow transit of the super-Earth exoplanet 55Cnce using a 2 m class telescope. Using differential spectrophotometry, we observed one transit in 2013 and another in 2014, with average spectral resolutions of ?700 and ?250, spanning the Johnson BVR photometric bands. We find a white light planet-to-star radius ratio of 0.0190{sub ?0.0027}{sup +0.0023} from the 2013 observations and 0.0200{sub ?0.0018}{sup +0.0017} from the 2014 observations. The two data sets combined result in a radius ratio of 0.0198{sub ?0.0014}{sup +0.0013}. These values are all in agreement with previous space-based results. Scintillation noise in the data prevents us from placing strong constraints on the presence of an extended hydrogen-rich atmosphere. Nevertheless, our detections of 55Cnce in transit demonstrate that moderate-sized telescopes on the ground will be capable of routine follow-up observations of super-Earth candidates discovered by the Transiting Exoplanet Survey Satellite around bright stars. We expect it also will be possible to place constraints on the atmospheric characteristics of those planets by devising observational strategies to minimize scintillation noise.

  12. A NEW LARGE SUPER-FAST ROTATOR: (335433) 2005 UW163

    SciTech Connect (OSTI)

    Chang, Chan-Kao; Lin, Hsing-Wen; Ip, Wing-Huen; Waszczak, Adam; Prince, Thomas A.; Kulkarni, Shrinivas R.; Laher, Russ; Surace, Jason

    2014-08-20

    Asteroids of size larger than 150m generally do not have rotation periods smaller than 2.2 hr. This spin cutoff is believed to be due to the gravitationally bound rubble-pile structures of the asteroids. Rotation with periods exceeding this critical value will cause asteroid breakup. Up until now, only one object, 2001 OE84, has been found to be an exception to this spin cutoff. We report the discovery of a new super-fast rotator, (335433) 2005 UW163, spinning with a period of 1.290 hr and a light curve variation of r' ? 0.8mag from the observations made at the P48 telescope and the P200 telescope of the Palomar Observatory. Its H{sub r{sup ?}}=17.690.27mag and multi-band colors (i.e., g' r' = 0.68 0.03mag, r' i' = 0.19 0.02mag and SDSS i z = 0.45mag) show it is a V-type asteroid with a diameter of 0.6 + 0.3/ 0.2 km. This indicates (335433) 2005 UW163 is a super-fast rotator beyond the regime of the small monolithic asteroid.

  13. Adsorptive separation of rhodium(III) using Fe(III)-templated oxine type of chemically modified chitosan

    SciTech Connect (OSTI)

    Alam, M.S.; Inoue, Katsutoshi; Yoshizuka, Kazuharu; Ishibashi, Hideaki

    1998-03-01

    The oxine type of chemically modified chitosan was prepared by the template crosslinking method using Fe(III) as a template ion. Batchwise adsorption of rhodium(III) on this chemically modified chitosan was examined from chloride media in the absence and presence of a large amount of tin(II). It was observed that the Fe(III)-templated oxine type of chemically modified chitosan shows better performance for rhodium adsorption than that of the original chitosan. When Sn(II) is absent from the solution, Rh(III) is hardly adsorbed on the modified chitosan and the order of selectivity of the adsorption of Rh(III), Pt(IV), and Cu(II) was found to be Pt(IV) > Cu(II) {approx} Rh(III). On the other hand, adsorption of rhodium is significantly increased in the presence of Sn(II) and the selectivity order of the adsorption was drastically changed to Rh(III) > Pt(IV) {much_gt} Cu(II), which ensures selective separation of Rh(III) from their mixture. Adsorption of Rh(III) increases with an increase in the concentration of Sn(II) in the aqueous solution, and maximum adsorption is achieved at a molar ratio, [Sn]/[Rh], of >6. The adsorption of Rh(III) decreases at a high concentration of hydrochloric acid. The maximum adsorption capacity was evaluated to be 0.92 mol/kg-dry adsorbent. Stripping tests of rhodium from the loaded chemically modified chitosan were carried out using different kinds of stripping agents containing some oxidizing agent. The maximum stripping of rhodium under these experimental conditions was found to be 72.5% by a single contact with 0.5 M HCl + 8 M HNO{sub 3}.

  14. Kicking the Tires | Jefferson Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    been doing and would like to do on superconducting radiofrequency cavities, on electron guns and on cryogenic engineering for the ILC. The team also provided a tour, which was...

  15. Studies on design of a process for organo-refining of coal to obtain super clean coal

    SciTech Connect (OSTI)

    Sharma, C.S.; Sharma, D.K.

    1999-08-01

    Organo-refining of coal results in refining the coal to obtain super clean coal and residual coal. Super clean coal may be used to obtain value added chemicals, products, and cleaner fuels from coal. In the present work, studies on the design of a semicontinuous process for organo-refining of one ton of coal have been made. The results are reported. This is only a cursory attempt for the design, and further studies may be required for designing this process for use in the development of a scaled-up process of organo-refining of coal.

  16. Maximum mass of stable magnetized highly super-Chandrasekhar white dwarfs: stable solutions with varying magnetic fields

    SciTech Connect (OSTI)

    Das, Upasana; Mukhopadhyay, Banibrata E-mail: bm@physics.iisc.ernet.in

    2014-06-01

    We address the issue of stability of recently proposed significantly super-Chandrasekhar white dwarfs. We present stable solutions of magnetostatic equilibrium models for super-Chandrasekhar white dwarfs pertaining to various magnetic field profiles. This has been obtained by self-consistently including the effects of the magnetic pressure gradient and total magnetic density in a general relativistic framework. We estimate that the maximum stable mass of magnetized white dwarfs could be more than 3 solar mass. This is very useful to explain peculiar, overluminous type Ia supernovae which do not conform to the traditional Chandrasekhar mass-limit.

  17. Super Boiler: Packed Media/Transport Membrane Boiler Development and Demonstration

    SciTech Connect (OSTI)

    Liss, William E; Cygan, David F

    2013-04-17

    Gas Technology Institute (GTI) and Cleaver-Brooks developed a new gas-fired steam generation system the Super Boiler for increased energy efficiency, reduced equipment size, and reduced emissions. The system consists of a firetube boiler with a unique staged furnace design, a two-stage burner system with engineered internal recirculation and inter-stage cooling integral to the boiler, unique convective pass design with extended internal surfaces for enhanced heat transfer, and a novel integrated heat recovery system to extract maximum energy from the flue gas. With these combined innovations, the Super Boiler technical goals were set at 94% HHV fuel efficiency, operation on natural gas with <5 ppmv NOx (referenced to 3%O2), and 50% smaller than conventional boilers of similar steam output. To demonstrate these technical goals, the project culminated in the industrial demonstration of this new high-efficiency technology on a 300 HP boiler at Clement Pappas, a juice bottler located in Ontario, California. The Super Boiler combustion system is based on two stage combustion which combines air staging, internal flue gas recirculation, inter-stage cooling, and unique fuel-air mixing technology to achieve low emissions rather than external flue gas recirculation which is most commonly used today. The two-stage combustion provides lower emissions because of the integrated design of the boiler and combustion system which permit precise control of peak flame temperatures in both primary and secondary stages of combustion. To reduce equipment size, the Super Boiler's dual furnace design increases radiant heat transfer to the furnace walls, allowing shorter overall furnace length, and also employs convective tubes with extended surfaces that increase heat transfer by up to 18-fold compared to conventional bare tubes. In this way, a two-pass boiler can achieve the same efficiency as a traditional three or four-pass firetube boiler design. The Super Boiler is consequently up to

  18. Luminescent cyclometallated iridium(III) complexes having acetylide ligands

    DOE Patents [OSTI]

    Thompson, Mark E.; Bossi, Alberto; Djurovich, Peter Ivan

    2014-09-02

    The present invention relates to phosphorescent (triplet-emitting) organometallic materials. The phosphorescent materials of the present invention comprise Ir(III)cyclometallated alkynyl complexes for use as triplet light-emitting materials. The Ir(III)cyclometallated alkynyl complexes comprise at least one cyclometallating ligand and at least one alkynyl ligand bonded to the iridium. Also provided is an organic light emitting device comprising an anode, a cathode and an emissive layer between the anode and the cathode, wherein the emissive layer comprises a Ir(III)cyclometallated alkynyl complex as a triplet emitting material.

  19. High efficiency III-nitride light-emitting diodes

    DOE Patents [OSTI]

    Crawford, Mary; Koleske, Daniel; Cho, Jaehee; Zhu, Di; Noemaun, Ahmed; Schubert, Martin F; Schubert, E. Fred

    2013-05-28

    Tailored doping of barrier layers enables balancing of the radiative recombination among the multiple-quantum-wells in III-Nitride light-emitting diodes. This tailored doping enables more symmetric carrier transport and uniform carrier distribution which help to reduce electron leakage and thus reduce the efficiency droop in high-power III-Nitride LEDs. Mitigation of the efficiency droop in III-Nitride LEDs may enable the pervasive market penetration of solid-state-lighting technologies in high-power lighting and illumination.

  20. Inductrack III configuration--a maglev system for high loads

    SciTech Connect (OSTI)

    Post, Richard F

    2013-11-12

    Inductrack III configurations are suited for use in transporting heavy freight loads. Inductrack III addresses a problem associated with the cantilevered track of the Inductrack II configuration. The use of a cantilevered track could present mechanical design problems in attempting to achieve a strong enough track system such that it would be capable of supporting very heavy loads. In Inductrack III, the levitating portion of the track can be supported uniformly from below, as the levitating Halbach array used on the moving vehicle is a single-sided one, thus does not require the cantilevered track as employed in Inductrack II.

  1. III-V Growth on Silicon Toward a Multijunction Cell

    SciTech Connect (OSTI)

    Geisz, J.; Olson, J.; McMahon, W.; Friedman, D.; Kibbler, A.; Kramer, C.; Young, M.; Duda, A.; Ward, S.; Ptak, A.; Kurtz, S.; Wanlass, M.; Ahrenkiel, P.; Jiang, C. S.; Moutinho, H.; Norman, A.; Jones, K.; Romero, M.; Reedy, B.

    2005-11-01

    A III-V on Si multijunction solar cell promises high efficiency at relatively low cost. The challenges to epitaxial growth of high-quality III-Vs on Si, though, are extensive. Lattice-matched (LM) dilute-nitride GaNPAs solar cells have been grown on Si, but their performance is limited by defects related to the nitrogen. Advances in the growth of lattice-mismatched (LMM) materials make more traditional III-Vs, such as GaInP and GaAsP, very attractive for use in multijunction solar cells on silicon.

  2. Inductrack III configuration--a maglev system for high loads

    DOE Patents [OSTI]

    Post, Richard F

    2015-03-24

    Inductrack III configurations are suited for use in transporting heavy freight loads. Inductrack III addresses a problem associated with the cantilevered track of the Inductrack II configuration. The use of a cantilevered track could present mechanical design problems in attempting to achieve a strong enough track system such that it would be capable of supporting very heavy loads. In Inductrack III, the levitating portion of the track can be supported uniformly from below, as the levitating Halbach array used on the moving vehicle is a single-sided one, thus does not require the cantilevered track as employed in Inductrack II.

  3. The Preparation of an Ultrastable Mesoporous Cr(III)-MOF via...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Abstract: Kinetic labilization of the Fe(III)-O coordination bond in a mesoporous metal-organic framework, PCN-333-Fe(III), is realized by the reduction of Fe(III) by Cr(II). The ...

  4. Evaluation of the Super ESPC Program: Level 2 -- Recalculated Cost Savings

    SciTech Connect (OSTI)

    Shonder, John A; Hughes, Patrick

    2009-04-01

    This report presents the results of Level 2 of a three-tiered evaluation of the U.S. Department of Energy Federal Energy Management Program's Super Energy Savings Performance Contract (Super ESPC) Program. Level 1 of the analysis studied all of the Super ESPC projects for which at least one Annual Measurement & Verification (M&V) Report had been produced by April 2006. For those 102 projects in aggregate, we found that the value of cost savings reported by the energy service company (ESCO) in the Annual M&V Reports was 108% of the cost savings guaranteed in the contracts. We also compared estimated energy savings (which are not guaranteed, but are the basis for the guaranteed cost savings) to the energy savings reported by the ESCO in the Annual M&V Report. In aggregate, reported energy savings were 99.8% of estimated energy savings on the basis of site energy, or 102% of estimated energy savings based on source energy. Level 2 focused on a random sample of 27 projects taken from the 102 Super ESPC projects studied in Level 1. The objectives were, for each project in the sample, to: repeat the calculations of the annual energy and cost savings in the most recent Annual M&V Report to validate the ESCO's results or correct any errors, and recalculate the value of the reported energy, water, and operations and maintenance (O&M) savings using actual utility prices paid at the project site instead of the 'contract' energy prices - the prices that are established in the project contract as those to be used by the ESCO to calculate the annual cost savings, which determine whether the guarantee has been met. Level 3 analysis will be conducted on three to five projects from the Level 2 sample that meet validity criteria for whole-building or whole-facility data analysis. This effort will verify energy and cost savings using statistical analysis of actual utility use, cost, and weather data. This approach, which can only be used for projects meeting particular validity

  5. Extended Deterrence, Nuclear Proliferation, and START III

    SciTech Connect (OSTI)

    Speed, R.D.

    2000-06-20

    Early in the Cold War, the United States adopted a policy of ''extended nuclear deterrence'' to protect its allies by threatening a nuclear strike against any state that attacks these allies. This threat can (in principle) be used to try to deter an enemy attack using conventional weapons or one using nuclear, chemical, or biological weapons. The credibility of a nuclear threat has long been subject to debate and is dependent on many complex geopolitical factors, not the least of which is the military capabilities of the opposing sides. The ending of the Cold War has led to a significant decrease in the number of strategic nuclear weapons deployed by the United States and Russia. START II, which was recently ratified by the Russian Duma, will (if implemented) reduce the number deployed strategic nuclear weapons on each side to 3500, compared to a level of over 11,000 at the end of the Cold War in 1991. The tentative limit established by Presidents Clinton and Yeltsin for START III would reduce the strategic force level to 2000-2500. However, the Russians (along with a number of arms control advocates) now argue that the level should be reduced even further--to 1500 warheads or less. The conventional view is that ''deep cuts'' in nuclear weapons are necessary to discourage nuclear proliferation. Thus, as part of the bargain to get the non-nuclear states to agree to the renewal of the Nuclear Non-Proliferation Treaty, the United States pledged to work towards greater reductions in strategic forces. Without movement in the direction of deep cuts, it is thought by many analysts that some countries may decide to build their own nuclear weapons. Indeed, this was part of the rationale India used to justify its own nuclear weapons program. However, there is also some concern that deep cuts (to 1500 or lower) in the U.S. strategic nuclear arsenal could have the opposite effect. The fear is that such cuts might undermine extended deterrence and cause a crisis in confidence

  6. QER- Comment of William Smith III

    Broader source: Energy.gov [DOE]

    ://www.rmi.org/Knowledge-Center/Library/E05-14_NuclearPowerEconomics.... If you have not yet done so, I strongly urge you to contact the Rocky Mountain Institute and contract with them for their advice in consulting on the Quadrennial Energy Review. Sincerely, William Wharton Smith III

  7. Monticello Mill Tailings Site Operable Unit III Annual Groundwater...

    Office of Legacy Management (LM)

    ... of a buried water pipeline to an existing solar evaporation pond for water treatment. ... the Abajo Mountains, U.S. Department of Energy Monticello Mill Tailings Site OU III ...

  8. EIS-0374: Klondike III/ Bigelow Canyon Wind Integration Project, OR

    Broader source: Energy.gov [DOE]

    This EIS analyzes BPA's decision to approve an interconnection requested by PPM Energy, Inc. (PPM) to integrate electrical power from their proposed Klondike III Wind roject (Wind Project) into the Federal Columbia River Transmission System (FCRTS).

  9. TOTAL SES SL EJ//EK EN IV EN III

    National Nuclear Security Administration (NNSA)

    SL EJEK EN IV EN III NN (Engineering) NQ (ProfTechAdmin) NU (TechAdminSupport) RETIREMENT ELIGIBLE TO RETIRE IMMEDIATELY 11 13.9% ELIGIBLE TO RETIRE BY 3272014 29 36.7%...

  10. Microsoft Word - FINAL Class 1 Revise TRUPACT-III Management...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... A.1 A-4 A-3 Item 1 Description: Revise the language in Attachment A1, "Container Storage," Section A1-1c(1) "TRUPACT-III Management" to address manual bolt removal from the ...

  11. III-V High-Efficiency Multijunction Photovoltaics (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2011-06-01

    Capabilities fact sheet that includes scope, core competencies and capabilities, and contact/web information for III-V High-Efficiency Multijunction Photovoltaics at the National Center for Photovoltaics.

  12. Proceedings of the Fermilab III Instabilities Workshop, held...

    Office of Scientific and Technical Information (OSTI)

    Title: Proceedings of the Fermilab III Instabilities Workshop, held at Fermilab June 25-29, 1990 Authors: Peggs, Stephen ; Harvey, M. Publication Date: 1990-08-01 OSTI Identifier: ...

  13. Utility-Interconnected Photovoltaic Systems STEVENS III,JOHN...

    Office of Scientific and Technical Information (OSTI)

    STEVENS III,JOHN W.; BONN,RUSSELL H.; GINN,JERRY W.; GONZALEZ,SIGIFREDO; KERN,GREG 14 SOLAR ENERGY; 24 POWER TRANSMISSION AND DISTRIBUTION; INTERCONNECTED POWER SYSTEMS;...

  14. Reactivity of Chromium(III) Nutritional Supplements in Biological...

    Office of Scientific and Technical Information (OSTI)

    Reactivities of Cr(III) complexes used in nutritional formulations, including Cr3O(OCOEt)6(OH2)3+ (A), Cr(pic)3 (pic) 2-pyridinecarboxylato(-) (B), and trans-CrCl2(OH2)4+ ...

  15. NREL: Photovoltaics Research - III-V Multijunction Materials and Devices

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    R&D III-V Multijunction Materials and Devices R&D NREL has a strong research capability in III-V multijunction photovoltaic (PV) cells. The inverted metamorphic multijunction (IMM) technology, which is fundamentally a new technology path with breakthrough performance and cost advantages, is a particular focus. We invented and first demonstrated the IMM solar cell and introduced it to the PV industry. Our scientists earlier invented and demonstrated the first-ever multijunction PV

  16. Table III: Technical Targets for Catalyst Coated Membranes (CCMs):

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Stationary | Department of Energy III: Technical Targets for Catalyst Coated Membranes (CCMs): Stationary Table III: Technical Targets for Catalyst Coated Membranes (CCMs): Stationary Technical targets for CCMs in stationary applications defined by the High Temperature Working Group (February 2003). technical_targets_ccms_stat.pdf (93.65 KB) More Documents & Publications R&D Plan for the High Temperature Membrane Working Group Table I: Technical Targets for Catalyst Coated Membranes

  17. III-Nitride Nanowires: Emerging Materials for Lighting and Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Applications | MIT-Harvard Center for Excitonics III-Nitride Nanowires: Emerging Materials for Lighting and Energy Applications March 20, 2012 at 3pm/36-428 George T. Wang Advanced Materials Science, Sandia National Laboratories Wang001_000 Abstract: Nanowires based on the III nitride (AlGaInN) materials system have attracted attention as potential nanoscale building blocks in LEDs, lasers, sensors, photovoltaics, and high power and high speed electronics. Compared to planar films,

  18. III-V/Si Wafer Bonding Using Transparent, Conductive Oxide Interlayers...

    Office of Scientific and Technical Information (OSTI)

    III-VSi Wafer Bonding Using Transparent, Conductive Oxide Interlayers; Article No. 263904 Citation Details In-Document Search Title: III-VSi Wafer Bonding Using Transparent, ...

  19. GRED Drilling Award … GRED III Phase II; 2010 Geothermal Technology...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Drilling Award GRED III Phase II; 2010 Geothermal Technology Program Peer Review Report GRED Drilling Award GRED III Phase II; 2010 Geothermal Technology Program Peer Review ...

  20. Search for proton decay via p??K+ using 260 kilotonyear data of Super-Kamiokande

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Abe, K.; Hayato, Y.; Iyogi, K.; Kameda, J.; Miura, M.; Moriyama, S.; Nakahata, M.; Nakayama, S.; Wendell, R.?A.; Sekiya, H.; et al

    2014-10-14

    We have searched for proton decay via p??K+ using Super-Kamiokande data from April 1996 to February 2013, 260 kilotonyear exposure in total. No evidence for this proton decay mode is found. A lower limit of the proton lifetime is set to ?/B(p??K+)>5.91033 years at 90% confidence level.

  1. Detecting breast microcalcifications using super-resolution and wave-equation ultrasound imaging: a numerical phantom study

    SciTech Connect (OSTI)

    Huang, Lianjie; Simonetti, Francesco; Huthwaite, Peter; Rosenberg, Robert; Williamson, Michael

    2010-01-01

    Ultrasound image resolution and quality need to be significantly improved for breast microcalcification detection. Super-resolution imaging with the factorization method has recently been developed as a promising tool to break through the resolution limit of conventional imaging. In addition, wave-equation reflection imaging has become an effective method to reduce image speckles by properly handling ultrasound scattering/diffraction from breast heterogeneities during image reconstruction. We explore the capabilities of a novel super-resolution ultrasound imaging method and a wave-equation reflection imaging scheme for detecting breast microcalcifications. Super-resolution imaging uses the singular value decomposition and a factorization scheme to achieve an image resolution that is not possible for conventional ultrasound imaging. Wave-equation reflection imaging employs a solution to the acoustic-wave equation in heterogeneous media to backpropagate ultrasound scattering/diffraction waves to scatters and form images of heterogeneities. We construct numerical breast phantoms using in vivo breast images, and use a finite-difference wave-equation scheme to generate ultrasound data scattered from inclusions that mimic microcalcifications. We demonstrate that microcalcifications can be detected at full spatial resolution using the super-resolution ultrasound imaging and wave-equation reflection imaging methods.

  2. Search for proton decay via p→νK+ using 260 kiloton·year data of Super-Kamiokande

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Abe, K.; Hayato, Y.; Iyogi, K.; Kameda, J.; Miura, M.; Moriyama, S.; Nakahata, M.; Nakayama, S.; Wendell, R. A.; Sekiya, H.; et al

    2014-10-14

    We have searched for proton decay via p→νK+ using Super-Kamiokande data from April 1996 to February 2013, 260 kiloton•year exposure in total. No evidence for this proton decay mode is found. A lower limit of the proton lifetime is set to τ/B(p→νK+)>5.9×1033 years at 90% confidence level.

  3. Project of a Super Charm-Tau factory at the Budker Institute of Nuclear Physics in Novosibirsk

    SciTech Connect (OSTI)

    Bondar, A. E.

    2013-09-15

    A project of a Super Charm-Tau factory is being developed at the Budker Institute of Nuclear Physics (Siberian Branch, Russian Academy of Sciences) in Novosibirsk. The electron-positron collider to be employed will operate at c.m. energies in the range between 2 and 5 GeV at an unprecedentedly high luminosity of 10{sup 35} cm{sup -2} s{sup -1} with a longitudinal electron polarization at the beam-interaction point. The main objective of experiments at the Super Charm-Tau factory is to study processes involving the production and properties of charmed quarks and tau leptons. A high luminosity of this setup will make it possible to obtain a statistical data sample that will be three to four orders of magnitude vaster than that from any other experiment performed thus far. Experiments at this setup are assumed to be sensitive to effects of new physics beyond the Standard Model. Investigations to be carried out at the Super-Charm-Tau factory will supplement future experiments at Super-B factories under construction in Italy and in Japan.

  4. A POSSIBLE EVOLUTIONARY SCENARIO OF HIGHLY MAGNETIZED SUPER-CHANDRASEKHAR WHITE DWARFS: PROGENITORS OF PECULIAR TYPE Ia SUPERNOVAE

    SciTech Connect (OSTI)

    Das, Upasana; Mukhopadhyay, Banibrata; Rao, A. R. E-mail: bm@physics.iisc.ernet.in

    2013-04-10

    Several recently discovered peculiar Type Ia supernovae seem to demand an altogether new formation theory that might help explain the puzzling dissimilarities between them and the standard Type Ia supernovae. The most striking aspect of the observational analysis is the necessity of invoking super-Chandrasekhar white dwarfs having masses {approx}2.1-2.8 M{sub Sun }, M{sub Sun} being the mass of Sun, as their most probable progenitors. Strongly magnetized white dwarfs having super-Chandrasekhar masses have already been established as potential candidates for the progenitors of peculiar Type Ia supernovae. Owing to the Landau quantization of the underlying electron degenerate gas, theoretical results yielded the observationally inferred mass range. Here, we sketch a possible evolutionary scenario by which super-Chandrasekhar white dwarfs could be formed by accretion on to a commonly observed magnetized white dwarf, invoking the phenomenon of flux freezing. This opens multiple possible evolution scenarios ending in supernova explosions of super-Chandrasekhar white dwarfs having masses within the range stated above. We point out that our proposal has observational support, such as the recent discovery of a large number of magnetized white dwarfs by the Sloan Digital Sky Survey.

  5. VOLATILE TRANSPORT INSIDE SUPER-EARTHS BY ENTRAPMENT IN THE WATER-ICE MATRIX

    SciTech Connect (OSTI)

    Levi, A.; Podolak, M.; Sasselov, D.

    2013-05-20

    Whether volatiles can be entrapped in a background matrix composing planetary envelopes and be dragged via convection to the surface is a key question in understanding atmospheric fluxes, cycles, and composition. In this paper, we consider super-Earths with an extensive water mantle (i.e., water planets), and the possibility of entrapment of methane in their extensive water-ice envelopes. We adopt the theory developed by van der Waals and Platteeuw for modeling solid solutions, often used for modeling clathrate hydrates, and modify it in order to estimate the thermodynamic stability field of a new phase called methane filled ice Ih. We find that in comparison to water ice VII the filled ice Ih structure may be stable not only at the high pressures but also at the high temperatures expected at the core-water mantle transition boundary of water planets.

  6. Qualification of welded super 13%Cr martensitic stainless steels for the Sgard field

    SciTech Connect (OSTI)

    Enerhaug, J.; Kvaale, P.E.; Bjordal, M.; Drugli, J.M.; Rogne, T.

    1999-11-01

    A test program was conducted to qualify welded super 13%Cr (S13%Cr) stainless steel for the Asgard Field, a mildly sour service. The test program involved girth welding, optimization of post weld heat treatment (PWHT) cycles, assessment of mechanical properties, examination of low cycle fatigue testing, and different corrosion testing and evaluation of S13%Cr steels from three different steel mills. The alloy with 0.015%C max, 11.9%Cr min, 2.4%Mo min and 6.O%Ni min, has been qualified for use as flowline material in the actual field. The results show acceptable weldability and corrosion properties. Post weld heat treatment (PWHT) of the welds improved the resistance against sulfide stress corrosion cracking.

  7. Comparison between beamforming and super resolution imaging algorithms for non-destructive evaluation

    SciTech Connect (OSTI)

    Fan, Chengguang; Drinkwater, Bruce W.

    2014-02-18

    In this paper the performance of total focusing method is compared with the widely used time-reversal MUSIC super resolution technique. The algorithms are tested with simulated and experimental ultrasonic array data, each containing different noise levels. The simulated time domain signals allow the effects of array geometry, frequency, scatterer location, scatterer size, scatterer separation and random noise to be carefully controlled. The performance of the imaging algorithms is evaluated in terms of resolution and sensitivity to random noise. It is shown that for the low noise situation, time-reversal MUSIC provides enhanced lateral resolution when compared to the total focusing method. However, for higher noise levels, the total focusing method shows robustness, whilst the performance of time-reversal MUSIC is significantly degraded.

  8. Super Energy Efficiency Design (S.E.E.D.) Home Evaluation

    SciTech Connect (OSTI)

    German, A.; Dakin, B.; Backman, C.; Weitzel, E.; Springer, D.

    2012-12-01

    This report describes the results of evaluation by the Alliance for Residential Building Innovation (ARBI) Building America team of the 'Super Energy Efficient Design' (S.E.E.D) home, a 1,935 sq. ft., single-story spec home located in Tucson, AZ. This prototype design was developed with the goal of providing an exceptionally energy efficient yet affordable home and includes numerous aggressive energy features intended to significantly reduce heating and cooling loads such as structural insulated panel (SIP) walls and roof, high performance windows, an ERV, an air-to-water heat pump with mixed-mode radiant and forced air delivery, solar water heating, and rooftop PV. Source energy savings are estimated at 45% over the Building America B10 Benchmark. System commissioning, short term testing, long term monitoring and detailed analysis of results was conducted to identify the performance attributes and cost effectiveness of the whole house measure package.

  9. Design of an accelerating cavity for the Superconducting Super Collider Low-Energy Booster

    SciTech Connect (OSTI)

    Friedrichs, C.C.; Walling, L. ); Campbell, B.M. )

    1991-01-01

    This paper presents the history and current status of the design of the accelerator cavity to be incorporated into the Low-Energy Booster (LEB) of the Superconducting Super Collider (SSC). The LEB is a proton synchrotron, 540 meters in circumference, and having 108 buckets around the ring. Acceleration programs, each 50 msec long, take place at a rate of 10 per second. The beta change of the particles from injection to extraction is from 0.8 to 0.997. Since the rf excitation frequency must track beta, the rf frequency must shift from 47.5 to 60 MHz over the 50-msec acceleration program. The cavity will use ferrite in a perpendicular control bias mode to effect the require tuning. 4 refs., 1 fig.

  10. Virtual and super - virtual refraction method: Application to synthetic data and 2012 of Karangsambung survey data

    SciTech Connect (OSTI)

    Nugraha, Andri Dian; Adisatrio, Philipus Ronnie

    2013-09-09

    Seismic refraction survey is one of geophysical method useful for imaging earth interior, definitely for imaging near surface. One of the common problems in seismic refraction survey is weak amplitude due to attenuations at far offset. This phenomenon will make it difficult to pick first refraction arrival, hence make it challenging to produce the near surface image. Seismic interferometry is a new technique to manipulate seismic trace for obtaining Green's function from a pair of receiver. One of its uses is for improving first refraction arrival quality at far offset. This research shows that we could estimate physical properties such as seismic velocity and thickness from virtual refraction processing. Also, virtual refraction could enhance the far offset signal amplitude since there is stacking procedure involved in it. Our results show super - virtual refraction processing produces seismic image which has higher signal-to-noise ratio than its raw seismic image. In the end, the numbers of reliable first arrival picks are also increased.

  11. Super-Planckian far-zone thermal emission from asymmetric hyperbolic metamaterials

    SciTech Connect (OSTI)

    Nefedov, Igor S.; Melnikov, Leonid A.

    2014-10-20

    We demonstrate the production of strong directive thermal emissions in the far-field zone of asymmetric hyperbolic metamaterials (AHMs), exceeding that predicted by Planck's limit. Asymmetry is inherent to the uniaxial medium, where the optical axis is tilted with respect to medium interfaces. The use of AHMs is shown to enhance the free-space coupling efficiency of thermally radiated waves, resulting in Super-Planckian far-field thermal emission in certain directions. This effect is impossible in usual hyperbolic materials because emission of high density of states (DOS) photons into vacuum with smaller DOS is preserved by the total internal reflection. Different plasmonic metamaterials are proposed for realizing AHM media; the thermal emission from a AHM, based on a grapheme multilayer structure, is presented, as an example.

  12. Analysis of Superconducting Dipole Coil of 11 GeV Super High Momentum Spectrometer

    SciTech Connect (OSTI)

    Sun, Eric; Cheng, Gary; Lassiter, Steve R.; Brindza, Paul D.; Fowler, Michael J.

    2015-06-01

    Jefferson Lab is constructing five Super High Momentum Spectrometer (SHMS) superconducting magnets for the 12 GeV Upgrade. This paper reports measured coil material properties and the results of the extensive finite element analysis (FEA) for the dipole coil. To properly define the smeared orthotropic material of the coil, a detailed coil model is set up to compute material parameters because not all parameters were measured. Stress and strain acceptance criteria are discussed. Eight load steps are defined. The preheat temperature of the force collar is optimized under two loading scenarios so that the positive pressure between the inner coil and central spacer is maintained while there is not too much squeeze to the coil.

  13. X-RAY EMISSION FROM THE SUPER-EARTH HOST GJ 1214

    SciTech Connect (OSTI)

    Lalitha, S.; Singh, K. P.; Poppenhaeger, K.; Czesla, S.; Schmitt, J. H. M. M.

    2014-07-20

    Stellar activity can produce large amounts of high-energy radiation, which is absorbed by the planetary atmosphere leading to irradiation-driven mass loss. We present the detection and an investigation of high-energy emission in a transiting super-Earth host system, GJ 1214, based on XMM-Newton observations. We derive an X-ray luminosity of L{sub X} = 7.4 10{sup 25}ergs{sup 1} and a corresponding activity level of log (L{sub X} /L {sub bol}) ? 5.3. Further, we determine a coronal temperature of about ?3.5MK, which is typical for coronal emission of moderately active low-mass stars. We estimate that GJ 1214 b evaporates at a rate of 1.3 10{sup 10}gs{sup 1} and has lost a total of ?2-5.6 M {sub ?}.

  14. Facile method to stain the bacterial cell surface for super-resolution fluorescence microscopy

    SciTech Connect (OSTI)

    Gunsolus, Ian L.; Hu, Dehong; Mihai, Cosmin; Lohse, Samuel E.; Lee, Chang-Soo; Torelli, Marco; Hamers, Robert J.; Murphy, Catherine; Orr, Galya; Haynes, Christy L.

    2014-01-01

    A method to fluorescently stain the surfaces of both Gram-negative and Gram-positive bacterial cells compatible with super-resolution fluorescence microscopy is presented. This method utilizes a commercially-available fluorescent probe to label primary amines at the surface of the cell. We demonstrate efficient staining of two bacterial strains, the Gram-negative Shewanella oneidensis MR-1 and the Gram-positive Bacillus subtilis 168. Using structured illumination microscopy and stochastic optical reconstruction microscopy, which require high quantum yield or specialized dyes, we show that this staining method may be used to resolve the bacterial cell surface with sub-diffraction-limited resolution. We further use this method to identify localization patterns of nanomaterials, specifically cadmium selenide quantum dots, following interaction with bacterial cells.

  15. Terahertz generation by mixing of two super-Gaussian laser beams in collisional plasma

    SciTech Connect (OSTI)

    Singh, Divya; Malik, Hitendra K. E-mail: hkmalik@physics.iitd.ac.in

    2014-08-15

    Considering a realistic situation, where electron-neutral collisions persist in plasma, analytical calculations are carried out for the Terahertz (THz) radiation generation by beating of two Super-Gaussian (SG) lasers of index p. The competency of these lasers over Gaussian lasers is discussed in detail with respect to the effects of collision and beam width on the THz field amplitude and efficiency of the mechanism. A critical transverse distance of the peak of the THz field is defined that shows a dependence on the index of SG lasers. Although electron-neutral collisions and larger beam width lead to the drastic reduction in the THz field when the SG lasers are used in the plasma, the efficiency of the mechanism remains much larger than the case of Gaussian lasers. Moreover, the higher index SG lasers produce stronger and focused THz radiation.

  16. Super Energy Efficient Design (S.E.E.D.) Home Evaluation

    SciTech Connect (OSTI)

    German, A.; Dakin, B.; Backman, C.; Weitzel, E.; Springer, D.

    2012-12-01

    This report describes the results of evaluation by the Alliance for Residential Building Innovation (ARBI) Building America team of the “Super Energy Efficient Design” (S.E.E.D) home, a 1,935 sq. ft., single-story spec home located in Tucson, AZ. This prototype design was developed with the goal of providing an exceptionally energy efficient yet affordable home and includes numerous aggressive energy features intended to significantly reduce heating and cooling loads such as structural insulated panel (SIP) walls and roof, high performance windows, an ERV, an air-to-water heat pump with mixed-mode radiant and forced air delivery, solar water heating, and rooftop PV. Source energy savings are estimated at 45% over the Building America B10 Benchmark. System commissioning, short term testing, long term monitoring and detailed analysis of results was conducted to identify the performance attributes and cost effectiveness of the whole house measure package.

  17. SuperLU{_}DIST: A scalable distributed-memory sparse direct solver for unsymmetric linear systems

    SciTech Connect (OSTI)

    Li, Xiaoye S.; Demmel, James W.

    2002-03-27

    In this paper, we present the main algorithmic features in the software package SuperLU{_}DIST, a distributed-memory sparse direct solver for large sets of linear equations. We give in detail our parallelization strategies, with focus on scalability issues, and demonstrate the parallel performance and scalability on current machines. The solver is based on sparse Gaussian elimination, with an innovative static pivoting strategy proposed earlier by the authors. The main advantage of static pivoting over classical partial pivoting is that it permits a priori determination of data structures and communication pattern for sparse Gaussian elimination, which makes it more scalable on distributed memory machines. Based on this a priori knowledge, we designed highly parallel and scalable algorithms for both LU decomposition and triangular solve and we show that they are suitable for large-scale distributed memory machines.

  18. SWIFT X-RAY OBSERVATIONS OF CLASSICAL NOVAE. II. THE SUPER SOFT SOURCE SAMPLE

    SciTech Connect (OSTI)

    Schwarz, Greg J.; Ness, Jan-Uwe; Osborne, J. P.; Page, K. L.; Evans, P. A.; Beardmore, A. P.; Walter, Frederick M.; Andrew Helton, L.; Woodward, Charles E.; Bode, Mike; Starrfield, Sumner; Drake, Jeremy J.

    2011-12-01

    The Swift gamma-ray burst satellite is an excellent facility for studying novae. Its rapid response time and sensitive X-ray detector provides an unparalleled opportunity to investigate the previously poorly sampled evolution of novae in the X-ray regime. This paper presents Swift observations of 52 Galactic/Magellanic Cloud novae. We included the X-Ray Telescope (0.3-10 keV) instrument count rates and the UltraViolet and Optical Telescope (1700-8000 A) filter photometry. Also included in the analysis are the publicly available pointed observations of 10 additional novae the X-ray archives. This is the largest X-ray sample of Galactic/Magellanic Cloud novae yet assembled and consists of 26 novae with Super Soft X-ray emission, 19 from Swift observations. The data set shows that the faster novae have an early hard X-ray phase that is usually missing in slower novae. The Super Soft X-ray phase occurs earlier and does not last as long in fast novae compared to slower novae. All the Swift novae with sufficient observations show that novae are highly variable with rapid variability and different periodicities. In the majority of cases, nuclear burning ceases less than three years after the outburst begins. Previous relationships, such as the nuclear burning duration versus t{sub 2} or the expansion velocity of the eject and nuclear burning duration versus the orbital period, are shown to be poorly correlated with the full sample indicating that additional factors beyond the white dwarf mass and binary separation play important roles in the evolution of a nova outburst. Finally, we confirm two optical phenomena that are correlated with strong, soft X-ray emission which can be used to further increase the efficiency of X-ray campaigns.

  19. A three-dimensional view of the thermal structure in a super-penumbral canopy

    SciTech Connect (OSTI)

    Beck, C.; Choudhary, D. P.; Rezaei, R.

    2014-06-20

    We investigate the three-dimensional (3D) thermal topology in a super-penumbral canopy of an active region (AR). We derive temperature stratifications in the AR by an inversion of the Ca II IR line at 854.2 nm, assuming local thermal equilibrium. We find that about half of the radially oriented fibrils in the super-penumbral canopy form short, low-lying (h < 1 Mm) loops in the 3D temperature cube. These closed loops connect from bright grains in or close to the penumbra to the photosphere a few Mms away from the sunspot. The other half of the fibrils monotonically rise with distance from the sunspot. Many of the fibrils show a central dark core and two lateral brightenings in line-core intensity images. The corresponding velocity image shows fibrils that are as wide as the fibrils seen in intensity without a lateral substructure. Additionally, we study a feature from a different class of structures without prominent mass flows. Its 3D topology is formed by two parallel, closed loops that connect patches of opposite polarity. We present evidence that the inverse Evershed flow into the sunspot in the lower chromosphere is the consequence of siphon flows along short loops that connect photospheric foot points. The dark-cored structure of the chromospheric fibrils cannot have a convective origin because of their location above regular granulation. The dark core most likely results from an opacity difference between the central axis and the lateral edges caused by the significant flow speed along the fibrils.

  20. Complexation of Curium(III) with DTPA at 10–70 °C: Comparison with Eu(III)–DTPA in Thermodynamics, Luminescence, and Coordination Modes

    SciTech Connect (OSTI)

    Tian, Guoxin; Zhang, Zhiyong; Martin, Leigh R.; Rao, Linfeng

    2015-02-16

    Separation of trivalent actinides (An(III)) from trivalent lanthanides (Ln(III)) is a challenging task because of their nearly identical chemical properties. Diethylenetriaminepentaacetate (DTPA), a key reagent used in the TALSPEAK process that effectively separates An(III) from Ln(III), is believed to play a critical role in the An(III)/Ln(III) separation. However, the underlying principles for the separation based on the difference in the complexation of DTPA with An(III) and Ln(III) remain unclear. In this work, the complexation of DTPA with Cm(III) at 10-70 ºC was investigated by spectrophotometry, luminescence spectroscopy, and microcalorimetry, in conjunction with computational methods. The binding strength, the enthalpy of complexation, the coordination modes, and the luminescence properties are compared between the Cm(III)-DTPA and Eu(III)-DTPA systems. The experimental and computational data have demonstrated that the difference between Cm(III) and Eu(III) in the binding strength with DTPA can be attributed to the stronger covalence bonding between Cm(III) and the nitrogen donors of DTPA.