Sample records for tinted window glass

  1. Dynamics of window glass fracture in explosions

    SciTech Connect (OSTI)

    Beauchamp, E.K.; Matalucci, R.V.

    1998-05-01T23:59:59.000Z

    An exploratory study was conducted under the Architectural Surety Program to examine the possibility of modifying fracture of glass in the shock-wave environment associated with terrorist bombings. The intent was to explore strategies to reduce the number and severity of injuries resulting from those attacks. The study consisted of a series of three experiments at the Energetic Materials Research and Testing Center (EMRTC) of the New Mexico Institute of Mining and Technology at Socorro, NM, in which annealed and tempered glass sheets were exposed to blast waves at several different levels of overpressure and specific impulse. A preliminary assessment of the response of tempered glass to the blast environment suggested that inducing early failure would result in lowering fragment velocity as well as reducing the loading from the window to the structure. To test that possibility, two different and novel procedures (indentation flaws and spot annealing) were used to reduce the failure strength of the tempered glass while maintaining its ability to fracture into small cube-shaped fragments. Each experiment involved a comparison of the performance of four sheets of glass with different treatments.

  2. High Reliability R-10 Windows Using Vacuum Insulating Glass Units

    SciTech Connect (OSTI)

    Stark, David

    2012-08-16T23:59:59.000Z

    The objective of this effort was for EverSealed Windows (“EverSealed” or “ESW”) to design, assemble, thermally and environmentally test and demonstrate a Vacuum Insulating Glass Unit (“VIGU” or “VIG”) that would enable a whole window to meet or exceed the an R-10 insulating value (U-factor ? 0.1). To produce a VIGU that could withstand any North American environment, ESW believed it needed to design, produce and use a flexible edge seal system. This is because a rigid edge seal, used by all other know VIG producers and developers, limits the size and/or thermal environment of the VIG to where the unit is not practical for typical IG sizes and cannot withstand severe outdoor environments. The rigid-sealed VIG’s use would be limited to mild climates where it would not have a reasonable economic payback when compared to traditional double-pane or triple-pane IGs. ESW’s goals, in addition to achieving a sufficiently high R-value to enable a whole window to achieve R-10, included creating a VIG design that could be produced for a cost equal to or lower than a traditional triple-pane IG (low-e, argon filled). ESW achieved these goals. EverSealed produced, tested and demonstrated a flexible edge-seal VIG that had an R-13 insulating value and the edge-seal system durability to operate reliably for at least 40 years in the harshest climates of North America.

  3. Development of a design procedure for architectural laminated glass window units

    E-Print Network [OSTI]

    Dice, Jeffrey Aaron

    1992-01-01T23:59:59.000Z

    DEVELOPMENT OF A DESIGN PROCEDURE FOR ARCHITECTURAL LAMINATED GLASS WINDOW UNITS A Thesis by JEFFREY AARON DICE Submitted to the Office of Graduate Studies of Texas ARM University in partial fulfillment of the requirements for the degree... of MASTER OF SCIENCE December 1992 Major Subject: Civil Engineering DEVELOPMENT OF A DESIGN PROCEDURE FOR ARCHITECTURAL LAMINATED GLASS WINDOW UNITS A Thesis by JEFFREY AARON DICE Approved as to style and content by: . L n Beason (Chair o Committee...

  4. Window Spacers and Edge Seals in Insulating Glass Units: A State-of-the-Art

    E-Print Network [OSTI]

    carbon dioxide (CO2) emissions in buildings is by increasing the thermal performance of their envelopes. Gustavsen Norwegian University of Science and Technology Windows and Envelope Materials Group Building), Windows & Envelope Materials Group, Berkeley, CA 94720- 8134, USA Abstract Insulating glass (IG) units

  5. Demonstration with Energy and Daylighting Assessment of Sunlight Responsive Thermochromic (SRT) Window Systems

    SciTech Connect (OSTI)

    Broekhuis, Michael; Liposcak, Curtis; Witte, Michael; Henninger, Robert; Zhou, Xiaohui; Petzen, George; Buchanan, Michael; Kumar, Sneh

    2012-03-31T23:59:59.000Z

    Pleotint, LLC was able to successfully extrude thermochromic interlayer for use in the fenestration industry. Pleotint has developed a thermochromic sytem that requires two thermochromic colors to make a neutral color when in the tinted state. These two colors were assembled into a single interlayer called a tri-layer prelam by Crown Operations for use in the glass lamination industry. Various locations, orientations, and constructions of thermochromic windows were studied with funds from this contract. Locations included Australia, California, Costa Rica, Indiana, Iowa, Mexico. Installed orientations included vertical and skylight glazing applications. Various constructions included monolithic, double pane, triple pane constructions. A daylighting study was conducted at LinEl Signature. LinEl Signature has a conference room with a sylight roof system that has a west orientation. The existing LinEl Signature conference room had constant tint 40% VLT transparent skylights. Irradiance meters were installed on the interior and exterior sides of a constant tint skylight. After a month and a half of data collection, the irradiance meters were removed and the constant tint skylights were replaced with Pleotint thermochromic skylight windows. The irradiance meters were reinstalled in the same locations and irradiance data was collected. Both data sets were compared. The data showed that there was a linear relationship with exterior and interior irradiance for the existing constant tint skylights. The thermochromic skylights have a non-linear relationship. The thermochromic skylights were able to limit the amount of irradiance that passed through the thermochromic skylight. A second study of the LinEl Signature conference was performed using EnergyPlus to calculate the amount of Illuminance that passed through constant tint skylights as compared to thermochromic skylights. The constant tint skylights transmitted Illuminance is 2.8 times higher than the thermochromic skylights during the months of May, June, July, August and 1.9 times higher than the thermochromic skylight during the months of March, April, September, October. Calculated illuminance levels were much more consistent as compared to the existing constant tint skylights installed at LinEl Signature. This allows for a more comfortable interior space in regard to glare discomfort and interior lighting control. Lawrence Berkeley National Laboratory was contracted to characterize the performance of the thermochromic interlayer and thermochromic window systems. Thermochromic interlayer was characterized with spectrometer equipment. The thermochromic window systems were characterized using LBNL’s Advanced Window Test Facility. A copy of the report can be found in the Appendix. Iowa State University was contracted to compare thermochromic window technology to constant tint technology. Iowa State University conducted the testing at the Energy Resource Station (ERS). The ERS has the ability to simultaneously test side-by-side competing building technologies. The building is equipped with two identical air handling units, each with its own dedicated and identical chiller. One air handling unit supplies the four test rooms designated as the A rooms and the other unit serves the four test rooms designated as the B rooms. There is one A test room and one B test rooms arranged as pairs in a side-by-side design with each pair having a different exposure. There is a pair of test rooms that face the south, an east and west facing pair. Each of the test rooms is a mirror image of its match with identical construction. The rooms are unoccupied; however, the capability to impose false loads on the rooms exists. The false loads and room lighting can be scheduled to simulate various usage patterns. A copy of the report can be found in the Appendix. GARD Analytics was contracted to compare EnergyPlus building simulations to the data recorded at the Iowa ERS. The goal of this research was to validate the building simulation software developed by the US Department of Energy. EnergyPlus is

  6. Sugar Land Facility Lighting and Window Tinting Upgrades

    E-Print Network [OSTI]

    Mesenbrink, C.

    Nalco/Exxon Energy Chemicals, L.P. (NEEC) is a global chemical company that creates and produces specialty chemicals for the Petroleum/Chemical industry. Although NEEC has facilities located around the globe, it's Corporate Administration Offices...

  7. NREL Electrochromic Window Research Wins Award

    ScienceCinema (OSTI)

    None

    2013-05-29T23:59:59.000Z

    Winners of the CO-LABS Governor's Award for High-Impact Research in Energy Efficiency, Dr. Satyen Deb at the U.S. Department of Energy's National Renewable Energy Laboratory (NREL) discovered that a small electrical charge can change the opacity of tungsten oxide from clear to tinted. He, Dr. Dane Gillaspie, and their fellow scientists at NREL then applied this knowledge to develop and transfer the technologies required to construct an electrochromic window, which can switch between clear and heavily tinted states. Electrochromic windows allow natural light in while adding tint to reduce summer heat and glare, and going clear to allow sunlight through in the winter. Broad adaptation of these windows could reduce US total energy use by four percent and reduce building cooling loads by 20%, much of this during expensive peak hours. Windows based on these discoveries are now being installed worldwide.

  8. Window Spacers and Edge Seals in Insulating Glass Units: A State-of-the-Art Review and Future Perspectives

    SciTech Connect (OSTI)

    SINTEF Building and Infrastructure; Norwegian University of Science and Technology (NTNU); Bergh, Sofie Van Den; Hart, Robert; Jelle, Bjrn Petter; Gustavsen, Arild

    2013-01-31T23:59:59.000Z

    Insulating glass (IG) units typically consist of multiple glass panes that are sealed and held together structurally along their perimeters. This report describes a study of edge seals in IG units. First, we summarize the components, requirements, and desired properties of edge construction in IG units, based on a survey of the available literature. Second, we review commercially available window edge seals and describe their properties, to provide an easily accessible reference for research and commercial purposes. Finally, based on the literature survey and review of current commercial edge seal systems, we identify research opportunities for future edge seal improvements and solutions.

  9. AN ENERGY EFFICIENT WINDOW SYSTEM FINAL REPORT.

    E-Print Network [OSTI]

    Authors, Various

    2011-01-01T23:59:59.000Z

    for a variety of glass window films and so provides thetesting metallized mylar window films. They involve exposingconsumers to install window film products. The rigid sheet

  10. The ultra-thin solar cells that could generate power through windows

    E-Print Network [OSTI]

    Rogers, John A.

    The ultra-thin solar cells that could generate power through windows By Claire Bates Last updated, generating enough electricity to power the GPS or air conditioning. Solar cells, which convert solar energy into tinted windows Page 1 of 3The ultra-thin solar cells that could generate power through windows | Mail

  11. Window shopping

    SciTech Connect (OSTI)

    Best, D.

    1990-03-01T23:59:59.000Z

    The author addresses the energy efficiency of windows and describes changes and new products available in this consumer information article. Experiments currently being done by Lawrence Berkeley Laboratory (LBL), Bonneville Power Authority and the Washington State Energy Office show that some of these superwindows collect more energy from the sun than they let escape from inside the home. One type of window in current production is the low-E (low-emissivity) and the IGUs (insulated glass units). Low-E techniques include glazing of the glass with various materials including polyester and metallic coatings. Other measures include filling the airspace in double pane windows with argon, aerogel or by creating a vacuum in the airspace. Another factor the author considers is ultraviolet light protection.

  12. Zero Energy Windows

    SciTech Connect (OSTI)

    Arasteh, Dariush; Selkowitz, Steve; Apte, Josh; LaFrance, Marc

    2006-05-17T23:59:59.000Z

    Windows in the U.S. consume 30 percent of building heating and cooling energy, representing an annual impact of 4.1 quadrillion BTU (quads) of primary energy. Windows have an even larger impact on peak energy demand and on occupant comfort. An additional 1 quad of lighting energy could be saved if buildings employed effective daylighting strategies. The ENERGY STAR{reg_sign} program has made standard windows significantly more efficient. However, even if all windows in the stock were replaced with today's efficient products, window energy consumption would still be approximately 2 quads. However, windows can be ''net energy gainers'' or ''zero-energy'' products. Highly insulating products in heating applications can admit more useful solar gain than the conductive energy lost through them. Dynamic glazings can modulate solar gains to minimize cooling energy needs and, in commercial buildings, allow daylighting to offset lighting requirements. The needed solutions vary with building type and climate. Developing this next generation of zero-energy windows will provide products for both existing buildings undergoing window replacements and products which are expected to be contributors to zero-energy buildings. This paper defines the requirements for zero-energy windows. The technical potentials in terms of national energy savings and the research and development (R&D) status of the following technologies are presented: (1) Highly insulating systems with U-factors of 0.1 Btu/hr-ft{sup 2}-F; (2) Dynamic windows: glazings that modulate transmittance (i.e., change from clear to tinted and/or reflective) in response to climate conditions; and (3) Integrated facades for commercial buildings to control/ redirect daylight. Market transformation policies to promote these technologies as they emerge into the marketplace are then described.

  13. Laser sealed vacuum insulation window

    DOE Patents [OSTI]

    Benson, David K. (Golden, CO); Tracy, C. Edwin (Golden, CO)

    1987-01-01T23:59:59.000Z

    A laser sealed evacuated window panel is comprised of two glass panes held spaced apart in relation to each other by a plurality of spherical glass beads and glass welded around the edges to provide an evacuated space between the glass panes that is completely glass sealed from the exterior. The glass welded edge seal is obtained by welding the edges of the glass panes together with a laser beam while the glass panes and bead spacers are positioned in a vacuum furnace and heated to the annealing point of the glass to avoid stress fracture in the area of the glass weld. The laser welding in the furnace can be directed around the perimeter of the glass panel by a combination of rotating the glass panel and linearly translating or aiming the laser with a relay mirror.

  14. Adaptive Liquid Crystal Windows

    SciTech Connect (OSTI)

    Taheri, Bahman; Bodnar, Volodymyr

    2011-12-31T23:59:59.000Z

    Energy consumption by private and commercial sectors in the U.S. has steadily grown over the last decade. The uncertainty in future availability of imported oil, on which the energy consumption relies strongly, resulted in a dramatic increase in the cost of energy. About 20% of this consumption are used to heat and cool houses and commercial buildings. To reduce dependence on the foreign oil and cut down emission of greenhouse gases, it is necessary to eliminate losses and reduce total energy consumption by buildings. To achieve this goal it is necessary to redefine the role of the conventional windows. At a minimum, windows should stop being a source for energy loss. Ideally, windows should become a source of energy, providing net gain to reduce energy used to heat and cool homes. It is possible to have a net energy gain from a window if its light transmission can be dynamically altered, ideally electronically without the need of operator assistance, providing optimal control of the solar gain that varies with season and climate in the U.S. In addition, the window must not require power from the building for operation. Resolution of this problem is a societal challenge and of national interest and will have a broad global impact. For this purpose, the year-round, allclimate window solution to provide an electronically variable solar heat gain coefficient (SHGC) with a wide dynamic range is needed. AlphaMicron, Inc. (AMI) developed and manufactured 1ft × 1ft prototype panels for the world’s first auto-adjusting Adaptive Liquid Crystal Windows (ALCWs) that can operate from sunlight without the need for external power source and demonstrate an electronically adjustable SHGC. This novel windows are based on AlphaMicron’s patented e-Tint® technology, a guesthost liquid crystal system implemented on flexible, optically clear plastic films. This technology is suitable both for OEM and aftermarket (retro-fitting) lamination to new and existing windows. Low level of power consumption by ALCWs allows for on-board power electronics for automatic matching of transmission through windows to varying climate conditions without drawing the power from the power grid. ALCWs are capable of transmitting more sunlight in winters to assist in heating and less sunlight in summers to minimize overheating. As such, they can change the window from being a source of energy loss to a source of energy gain. In addition, the scalable AMI’s roll-to-roll process, proved by making 1ft × 1ftALCW prototype panels, allows for cost-effective production of large-scale window panels along with capability to change easily their color and shape. In addition to architectural glazing in houses and commercial buildings, ALCWs can be used in other applications where control of sunlight is needed, such as green houses, used by commercial produce growers and botanical gardens, cars, aircrafts, etc.

  15. THE IMPACT OF A TANK 40H DECANT ON THE PROJECTED OPERATING WINDOWS FOR SB4 AND GLASS SELECTION STRATEGY IN SUPPORT OF THE VARIABILITY STUDY

    SciTech Connect (OSTI)

    Raszewski, F; Tommy Edwards, T; David Peeler, D

    2008-02-07T23:59:59.000Z

    The Liquid Waste Organization (LWO) has requested that the Savannah River National Laboratory (SRNL) to assess the impact of a 100K gallon decant volume from Tank 40H on the existing sludge-only Sludge Batch 4 (SB4)-Frit 510 flowsheet and the coupled operations flowsheet (SB4 with the Actinide Removal Process (ARP)). Another potential SB4 flowsheet modification of interest includes the addition of 3 wt% sodium (on a calcined oxide basis) to a decanted sludge-only or coupled operations flowsheet. These potential SB4 flowsheet modifications could result in significant compositional shifts to the SB4 system. This paper study provides an assessment of the impact of these compositional changes to the projected glass operating windows and to the variability study for the Frit 510-SB4 system. The influence of the compositional changes on melt rate was not assessed in this study nor was it requested. Nominal Stage paper study assessments were completed using the projected compositions for the various flowsheet options coupled with Frit 510 (i.e., variation was not applied to the sludge and frit compositions). In order to gain insight into the impacts of sludge variation and/or frit variation (due to the procurement specifications) on the projected operating windows, three versions of the Variation Stage assessment were performed: (1) the traditional Variation Stage assessment in which the nominal Frit 510 composition was coupled with the extreme vertices (EVs) of each sludge, (2) an assessment of the impact of possible frit variation (within the accepted frit specification tolerances) on each nominal SB4 option, and (3) an assessment of the impact of possible variation in the Frit 510 composition due to the vendor's acceptance specifications coupled with the EVs of each sludge case. The results of the Nominal Stage assessment indicate very little difference among the various flowsheet options. All of the flowsheets provide DWPF with the possibility of targeting waste loadings (WLs) from the low 30s to the low 40s with Frit 510. In general, the Tank 40H decant has a slight negative impact on the operating window, but DWPF still has the ability to target current WLs (34%) and higher WLs if needed. While the decant does not affect practical WL targets in DWPF, melt rate could be reduced due to the lower Na{sub 2}O content. If true, the addition of 3 wt% Na{sub 2}O to the glass system may regain melt rate, assuming that the source of alkali is independent of the impact on melt rate. Coupled operations with Frit 510 via the addition of ARP to the decanted SB4 flowsheet also appears to be viable based on the projected operating windows. The addition of both ARP and 3 wt% Na{sub 2}O to a decanted Tank 40H sludge may be problematic using Frit 510. Although the Nominal Stage assessments provide reasonable operating windows for the SB4 flowsheets being considered with Frit 510, introduction of potential sludge and/or frit compositional variation does have a negative impact. The magnitude of the impact on the projected operating windows is dependent on the specific flowsheet options as well as the applied variation. The results of the traditional Variation Stage assessments indicate that the three proposed Tank 40H decanted flowsheet options (Case No.2--100K gallon decant, Case No.3--100K gallon decant and 3 wt% Na{sub 2}O addition and Case No.4--100K gallon decant and ARP) demonstrate a relatively high degree of robustness to possible sludge variation over WLs of interest with Frit 510. However, the case where the addition of both ARP and 3 wt% Na{sub 2}O is considered was problematic during the traditional Variation Stage assessment. The impact of coupling the frit specifications with the nominal SB4 flowsheet options on the projected operating windows is highly dependent on whether the upper WLs are low viscosity or liquidus temperature limited in the Nominal Stage assessments. Systems that are liquidus temperature limited exhibit a high degree of robustness to the applied frit and sludge variation, while those that are low viscosity li

  16. ENERGY EFFICIENT WINDOWS PROGRAM. CHAPTER FROM THE ENERGY AND ENVIRONMENT DIVISION ANNUAL REPORT 1979

    E-Print Network [OSTI]

    Berman, S.

    2013-01-01T23:59:59.000Z

    Replacing window glass with a thin plastic film coated to beof windows can be improved with the use of thin-film coat-windows, the coating can be deposited directly on glass or on plastic films

  17. Laser sealed vacuum insulating window

    DOE Patents [OSTI]

    Benson, D.K.; Tracy, C.E.

    1985-08-19T23:59:59.000Z

    A laser sealed evacuated window panel is comprised of two glass panes held spaced apart in relation to each other by a plurality of spherical glass beads and glass welded around the edges to provide an evacuated space between the glass panes that is completely glass sealed from the exterior. The glass welded edge seal is obtained by welding the edges of the glass panes together with a laser beam while the glass panes and bead spacers are positioned in a vacuum furnace and heated to the annealing point of the glass to avoid stress fracture in the area of the glass weld. The laser welding in the furnace can be directed around the perimeter of the galss panel by a combination of rotating the glass panel and linearly translating or aiming the laser with a relay mirror.

  18. A Design Guide for Early-Market Electrochromic Windows

    SciTech Connect (OSTI)

    Lee, Eleanor S.; Selkowitz, Stephen E.; Clear, Robert D.; DiBartolomeo, Dennis L.; Klems, Joseph H.; Fernandes, Luis L.; Ward, GregJ.; Inkarojrit, Vorapat; Yazdanian, Mehry

    2006-05-01T23:59:59.000Z

    Switchable variable-tint electrochromic (EC) windows preserve view out while modulating transmitted light, glare, and solar heat gains. Consumers will require objective information on the risks and benefits of this emerging technology as it enters the market in 2006. This guide provides such information and data derived from a wide variety of simulations, laboratory tests, and a 2.5-year field test of prototype large-area EC windows evaluated under outdoor sun and sky conditions. This design guide is provided to architects, engineers, building owners, and others interested in electrochromic windows. The design guide provides basic information about what is an electrochromic window, what it looks like, how fast does it switch, and what current product offerings are. The guide also provides information on performance benefits if more mature product offerings were available.

  19. Industrial Risks and Land use Planning Study of blast window resistance

    E-Print Network [OSTI]

    Boyer, Edmond

    glasses with or without anti-explosion film, laminated glasses...), mobile frames or window locking a short time (inferior to 10 ms). Coevert and al. [5] also studied security window film and insulating/16/4 with Insulating glass fabricated with laminated glass (a) Figure 4: (a) security window film, (c) · The behaviour

  20. Window-closing safety system

    DOE Patents [OSTI]

    McEwan, Thomas E. (Livermore, CA)

    1997-01-01T23:59:59.000Z

    A safety device includes a wire loop embedded in the glass of a passenger car window and routed near the closing leading-edge of the window. The wire loop carries microwave pulses around the loop to and from a transceiver with separate output and input ports. An evanescent field only and inch or two in radius is created along the wire loop by the pulses. Just about any object coming within the evanescent field will dramatically reduce the energy of the microwave pulses received back by the transceiver. Such a loss in energy is interpreted as a closing area blockage, and electrical interlocks are provided to halt or reverse a power window motor that is actively trying to close the window.

  1. Window-closing safety system

    DOE Patents [OSTI]

    McEwan, T.E.

    1997-08-26T23:59:59.000Z

    A safety device includes a wire loop embedded in the glass of a passenger car window and routed near the closing leading-edge of the window. The wire loop carries microwave pulses around the loop to and from a transceiver with separate output and input ports. An evanescent field only an inch or two in radius is created along the wire loop by the pulses. Just about any object coming within the evanescent field will dramatically reduce the energy of the microwave pulses received back by the transceiver. Such a loss in energy is interpreted as a closing area blockage, and electrical interlocks are provided to halt or reverse a power window motor that is actively trying to close the window. 5 figs.

  2. Advancement of Electrochromic Windows

    E-Print Network [OSTI]

    2006-01-01T23:59:59.000Z

    Guide for Early-Market Electrochromic Windows. LBNL-59950.Guide for Early-Market Electrochromic Windows Attachment 17:electrochromic prototype windows that were deemed sufficiently mature for market

  3. Zero Energy Windows

    E-Print Network [OSTI]

    Arasteh, Dariush; Selkowitz, Steve; Apte, Josh; LaFrance, Marc

    2006-01-01T23:59:59.000Z

    Energy Performance of Electrochromic Windows Controlled for2006). Advancement of Electrochromic Windows, CaliforniaSavings Potential of Electrochromic Windows in the U.S.

  4. Residential Windows and Window Coverings: A Detailed View of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Residential Windows and Window Coverings: A Detailed View of the Installed Base and User Behavior Residential Windows and Window Coverings: A Detailed View of the Installed Base...

  5. Advancement of Electrochromic Windows

    E-Print Network [OSTI]

    2006-01-01T23:59:59.000Z

    of a thin-film ceramic electrochromic window: Field studyof a Thin-Film Ceramic Electrochromic Window: Field StudyEC window product characteristics The EC is a thin-film WO3-

  6. Advancement of Electrochromic Windows

    E-Print Network [OSTI]

    2006-01-01T23:59:59.000Z

    Guide for Early-Market Electrochromic Windows. LBNL-59950.Granqvist, C.G. 2000. "Electrochromic Tungsten Oxide Films:the performance of the electrochromic windows. Proceedings

  7. Beautify Your Windows and Glass Walls.

    E-Print Network [OSTI]

    Tompkins, Charlotte

    1961-01-01T23:59:59.000Z

    -utside? How do your dqkrie outside of your house? 2 IlnKY color affect , Coloor, De~kn and Tex When choosing draperies to har- monize with a room, consider the room, proportions, exposure, view, walls, floors, furnishings, accessories...

  8. Method of making an integral window hermetic fiber optic component

    DOE Patents [OSTI]

    Dalton, Rick D. (Miamisburg, OH); Kramer, Daniel P. (Centerville, OH); Massey, Richard T. (Hamilton, OH); Waker, Damon A. (Bellbrook, OH)

    1996-11-12T23:59:59.000Z

    In the fabrication of igniters, actuators, detonators, and other pyrotechnic devices to be activated by a laser beam, an integral optical glass window is formed by placing a preform in the structural member of the device and then melting the glass and sealing it in place by heating at a temperature between the ceramming temperature of the glass and the melting point of the metal, followed by rapid furnace cooling to avoid devitrification. No other sealing material is needed to achieve hermeticity. A preferred embodiment of this type of device is fabricated by allowing the molten glass to flow further and form a plano-convex lens integral with and at the bottom of the window. The lens functions to decrease the beam divergence caused by refraction of the laser light passing through the window when the device is fired by means of a laser beam.

  9. Method of making an integral window hermetic fiber optic component

    DOE Patents [OSTI]

    Dalton, R.D.; Kramer, D.P.; Massey, R.T.; Waker, D.A.

    1996-11-12T23:59:59.000Z

    In the fabrication of igniters, actuators, detonators, and other pyrotechnic devices to be activated by a laser beam, an integral optical glass window is formed by placing a preform in the structural member of the device and then melting the glass and sealing it in place by heating at a temperature between the ceramming temperature of the glass and the melting point of the metal, followed by rapid furnace cooling to avoid devitrification. No other sealing material is needed to achieve hermeticity. A preferred embodiment of this type of device is fabricated by allowing the molten glass to flow further and form a plano-convex lens integral with and at the bottom of the window. The lens functions to decrease the beam divergence caused by refraction of the laser light passing through the window when the device is fired by means of a laser beam. 9 figs.

  10. Solar optical materials for innovative window design

    SciTech Connect (OSTI)

    Lampert, C.M.

    1982-08-01T23:59:59.000Z

    New and innovative optical materials and coatings can greatly improve the efficiency of window energy systems. These potential materials and coatings increase energy efficiency by reducing radiative losses in the infrared, or reducing visible reflection losses or controlling overheating due to solar gain. Current progress in heat mirror coatings for glass and polymeric substrates is presented. Highly doped semiconducting oxides and metal/dielectric interference coatings are reviewed. Physical and optical properties are outlined for antireflection films and transparent aerogel insulation media. The potential for optical switching films as window elements includes discussions of electrochromic, photochromic and other physical switching processes.

  11. Efficient Windows Collaborative

    SciTech Connect (OSTI)

    Nils Petermann

    2010-02-28T23:59:59.000Z

    The project goals covered both the residential and commercial windows markets and involved a range of audiences such as window manufacturers, builders, homeowners, design professionals, utilities, and public agencies. Essential goals included: (1) Creation of 'Master Toolkits' of information that integrate diverse tools, rating systems, and incentive programs, customized for key audiences such as window manufacturers, design professionals, and utility programs. (2) Delivery of education and outreach programs to multiple audiences through conference presentations, publication of articles for builders and other industry professionals, and targeted dissemination of efficient window curricula to professionals and students. (3) Design and implementation of mechanisms to encourage and track sales of more efficient products through the existing Window Products Database as an incentive for manufacturers to improve products and participate in programs such as NFRC and ENERGY STAR. (4) Development of utility incentive programs to promote more efficient residential and commercial windows. Partnership with regional and local entities on the development of programs and customized information to move the market toward the highest performing products. An overarching project goal was to ensure that different audiences adopt and use the developed information, design and promotion tools and thus increase the market penetration of energy efficient fenestration products. In particular, a crucial success criterion was to move gas and electric utilities to increase the promotion of energy efficient windows through demand side management programs as an important step toward increasing the market share of energy efficient windows.

  12. Windows technology assessment

    SciTech Connect (OSTI)

    Baron, J.J.

    1995-10-01T23:59:59.000Z

    This assessment estimates that energy loss through windows is approximately 15 percent of all the energy used for space heating and cooling in residential and commercial buildings in New York State. The rule of thumb for the nation as a whole is about 25 percent. The difference may reflect a traditional assumption of single-pane windows while this assessment analyzed installed window types in the region. Based on the often-quoted assumption, in the United States some 3.5 quadrillion British thermal units (Btu) of primary energy, costing some $20 billion, is annually consumed as a result of energy lost through windows. According to this assessment, in New York State, the energy lost due to heat loss through windows is approximately 80 trillion Btu at an annual cost of approximately $1 billion.

  13. The Efficient Windows Collaborative

    SciTech Connect (OSTI)

    Petermann, Nils

    2006-03-31T23:59:59.000Z

    The Efficient Windows Collaborative (EWC) is a coalition of manufacturers, component suppliers, government agencies, research institutions, and others who partner to expand the market for energy efficient window products. Funded through a cooperative agreement with the U.S. Department of Energy, the EWC provides education, communication and outreach in order to transform the residential window market to 70% energy efficient products by 2005. Implementation of the EWC is managed by the Alliance to Save Energy, with support from the University of Minnesota and Lawrence Berkeley National Laboratory.

  14. Subject Responses to Electrochromic Windows

    E-Print Network [OSTI]

    Clear, Robert; Inkarojrit, Vorapat; Lee, Eleanor

    2006-01-01T23:59:59.000Z

    Visual quality assessment of electrochromic and conventionalissues for large-area electrochromic windows in commercialOffice worker preferences of electrochromic windows: a pilot

  15. CH7 Windows Introduction

    E-Print Network [OSTI]

    Collette. SĂ©bastien

    4 Server · Account lockout security ­ Protection contre les attaques sur les mots de passe Windows NT 4 Server · Account lockout security ­ Protection contre les attaques sur les mots de passe

  16. Superconducting radiofrequency window assembly

    DOE Patents [OSTI]

    Phillips, H.L.; Elliott, T.S.

    1997-03-11T23:59:59.000Z

    The present invention is a superconducting radiofrequency window assembly for use in an electron beam accelerator. The srf window assembly has a superconducting metal-ceramic design. The srf window assembly comprises a superconducting frame, a ceramic plate having a superconducting metallized area, and a superconducting eyelet for sealing plate into frame. The plate is brazed to eyelet which is then electron beam welded to frame. A method for providing a ceramic object mounted in a metal member to withstand cryogenic temperatures is also provided. The method involves a new metallization process for coating a selected area of a ceramic object with a thin film of a superconducting material. Finally, a method for assembling an electron beam accelerator cavity utilizing the srf window assembly is provided. The procedure is carried out within an ultra clean room to minimize exposure to particulates which adversely affect the performance of the cavity within the electron beam accelerator. 11 figs.

  17. Superconductive radiofrequency window assembly

    DOE Patents [OSTI]

    Phillips, H.L.; Elliott, T.S.

    1998-05-19T23:59:59.000Z

    The present invention is a superconducting radiofrequency window assembly for use in an electron beam accelerator. The SRF window assembly has a superconducting metal-ceramic design. The SRF window assembly comprises a superconducting frame, a ceramic plate having a superconducting metallized area, and a superconducting eyelet for sealing plate into frame. The plate is brazed to eyelet which is then electron beam welded to frame. A method for providing a ceramic object mounted in a metal member to withstand cryogenic temperatures is also provided. The method involves a new metallization process for coating a selected area of a ceramic object with a thin film of a superconducting material. Finally, a method for assembling an electron beam accelerator cavity utilizing the SRF window assembly is provided. The procedure is carried out within an ultra clean room to minimize exposure to particulates which adversely affect the performance of the cavity within the electron beam accelerator. 11 figs.

  18. High Performance Window Retrofit

    SciTech Connect (OSTI)

    Shrestha, Som S [ORNL; Hun, Diana E [ORNL; Desjarlais, Andre Omer [ORNL

    2013-12-01T23:59:59.000Z

    The US Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy (EERE) and Traco partnered to develop high-performance windows for commercial building that are cost-effective. The main performance requirement for these windows was that they needed to have an R-value of at least 5 ft2 F h/Btu. This project seeks to quantify the potential energy savings from installing these windows in commercial buildings that are at least 20 years old. To this end, we are conducting evaluations at a two-story test facility that is representative of a commercial building from the 1980s, and are gathering measurements on the performance of its windows before and after double-pane, clear-glazed units are upgraded with R5 windows. Additionally, we will use these data to calibrate EnergyPlus models that we will allow us to extrapolate results to other climates. Findings from this project will provide empirical data on the benefits from high-performance windows, which will help promote their adoption in new and existing commercial buildings. This report describes the experimental setup, and includes some of the field and simulation results.

  19. The Window Market in Texas: Opportunities for Energy Savings and Demand Reduction

    E-Print Network [OSTI]

    Zarnikau, J.; Campbell, L.

    2002-01-01T23:59:59.000Z

    The use of high performance windows represents a promising opportunity to reduce energy consumption and summer electrical demand in homes and commercial buildings in Texas and neighboring states. While low-e glass coatings and other energy...

  20. E-Print Network 3.0 - alumino-borosilicate glass developed Sample...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Qub Summary: represents development in glass science. It has led to the recognition of self-organization in disordered... Reversibility window in as-quenched Ge-As-S glasses E. C...

  1. Silver nanowire transparent electrodes for liquid crystal-based smart windows

    E-Print Network [OSTI]

    Goldthorpe, Irene

    privacy glass or as energy saving windows through the modulation of solar heat gain [1,3,4]. The operating sheet resistance, and low-cost. While the benefits of increased transparency and low-cost are obvious Polymer dispersed liquid crystal Smart window a b s t r a c t A significant manufacturing cost of polymer

  2. Windows XP - LPR Printing

    E-Print Network [OSTI]

    dbrown

    2004-07-27T23:59:59.000Z

    To print to the math department printers in Windows XP, “Print Services for Unix” must be ... Page 3 ... The wizard will proceed to install "Print Services for Unix". ... Email systems@math.purdue.edu if you need assistance. D. Brown. 7/26/04.

  3. Superconducting radiofrequency window assembly

    DOE Patents [OSTI]

    Phillips, Harry L. (Seaford, VA); Elliott, Thomas S. (Yorktown, VA)

    1997-01-01T23:59:59.000Z

    The present invention is a superconducting radiofrequency window assembly for use in an electron beam accelerator. The srf window assembly (20) has a superconducting metal-ceramic design. The srf window assembly (20) comprises a superconducting frame (30), a ceramic plate (40) having a superconducting metallized area, and a superconducting eyelet (50) for sealing plate (40) into frame (30). The plate (40) is brazed to eyelet (50) which is then electron beam welded to frame (30). A method for providing a ceramic object mounted in a metal member to withstand cryogenic temperatures is also provided. The method involves a new metallization process for coating a selected area of a ceramic object with a thin film of a superconducting material. Finally, a method for assembling an electron beam accelerator cavity utilizing the srf window assembly is provided. The procedure is carried out within an ultra clean room to minimize exposure to particulates which adversely affect the performance of the cavity within the electron beam accelerator.

  4. Superconductive radiofrequency window assembly

    DOE Patents [OSTI]

    Phillips, Harry Lawrence (Seaford, VA); Elliott, Thomas S. (Yorktown, VA)

    1998-01-01T23:59:59.000Z

    The present invention is a superconducting radiofrequency window assembly for use in an electron beam accelerator. The srf window assembly (20) has a superconducting metal-ceramic design. The srf window assembly (20) comprises a superconducting frame (30), a ceramic plate (40) having a superconducting metallized area, and a superconducting eyelet (50) for sealing plate (40) into frame (30). The plate (40) is brazed to eyelet (50) which is then electron beam welded to frame (30). A method for providing a ceramic object mounted in a metal member to withstand cryogenic temperatures is also provided. The method involves a new metallization process for coating a selected area of a ceramic object with a thin film of a superconducting material. Finally, a method for assembling an electron beam accelerator cavity utilizing the srf window assembly is provided. The procedure is carried out within an ultra clean room to minimize exposure to particulates which adversely affect the performance of the cavity within the electron beam accelerator.

  5. Windows and lighting program

    SciTech Connect (OSTI)

    Not Available

    1990-06-01T23:59:59.000Z

    More than 30% of all energy use in buildings is attributable to two sources: windows and lighting. Together they account for annual consumer energy expenditures of more than $50 billion. Each affects not only energy use by other major building systems, but also comfort and productivity -- factors that influence building economics far more than does direct energy consumption alone. Windows play a unique role in the building envelope, physically separating the conditioned space from the world outside without sacrificing vital visual contact. Throughout the indoor environment, lighting systems facilitate a variety of tasks associated with a wide range of visual requirements while defining the luminous qualities of the indoor environment. Windows and lighting are thus essential components of any comprehensive building science program. Despite important achievements in reducing building energy consumption over the past decade, significant additional savings are still possible. These will come from two complementary strategies: (1) improve building designs so that they effectively apply existing technologies and extend the market penetration of these technologies; and (2) develop advanced technologies that increase the savings potential of each application. Both the Windows and Daylighting Group and the Lighting System Research Group have made substantial contributions in each of these areas, and continue to do so through the ongoing research summarized here. 23 refs., 16 figs.

  6. Carbon smackdown: smart windows

    ScienceCinema (OSTI)

    Delia Milliron

    2010-09-01T23:59:59.000Z

    August 3, 2010 Berkeley Lab talk: In the fourth of five Carbon Smackdown matches, Berkeley Lab researchers Delia Milliron of the Materials Sciences Division and Stephen Selkowitz of the Environmental Energy Technologies Division talk about their work on energy-saving smart windows.

  7. Zero Energy Windows

    E-Print Network [OSTI]

    Arasteh, Dariush; Selkowitz, Steve; Apte, Josh; LaFrance, Marc

    2006-01-01T23:59:59.000Z

    impact of 4.1 quadrillion BTU (quads) of primary energy 1 .systems with U-factors of 0.1 Btu/hr-ft˛-°F Dynamic windows:for 1 quadrillion (10 15 ) Btu = 1.056 EJ. percent (Apte,

  8. ridescent butterfly scales are visually stunning structures that reflect highly sat-

    E-Print Network [OSTI]

    Johnsen, Sönke

    in spectrum and intensity. Coloured light from thin-film irides- cence, as in the iridescent members and visible light, were polariza- tion-neutral, isotropic colourless plastic and grey-tinted window glass above the window was counted by eye over a 10-min period for the depolarized and control conditions

  9. Localised mobilisation of metals, as measured by diffusive gradients in thin-films, in soil historically treated with sewage sludge

    E-Print Network [OSTI]

    Ma, Lena

    in spectrum and intensity. Coloured light from thin-film irides- cence, as in the iridescent members and visible light, were polariza- tion-neutral, isotropic colourless plastic and grey-tinted window glass above the window was counted by eye over a 10-min period for the depolarized and control conditions

  10. The Window Strategy with Options

    E-Print Network [OSTI]

    McCorkle, Dean; Amosson, Stephen H.; Fausett, Marvin

    1999-06-23T23:59:59.000Z

    The window strategy is one of several marketing strategies using futures and options to establish a floor price and allow for upside price potential. It also reduces option premium costs. This publication discusses how the window strategy works...

  11. Performance Criteria for Residential Zero Energy Windows

    E-Print Network [OSTI]

    Arasteh, Dariush; Goudey, Howdy; Huang, Joe; Kohler, Christian; Mitchell, Robin

    2006-01-01T23:59:59.000Z

    neutral energy impact of windows (energy consumption of buildingneutral energy impact of windows (energy consumption of buildingneutral energy impact of windows (energy consumption of building

  12. A Review of Electrochromic Window Performance Factors

    E-Print Network [OSTI]

    Selkowitz Ed, S.E.

    2010-01-01T23:59:59.000Z

    ratio of 0.30. The electrochromic windows were controlled toProceedings. A Review of Electrochromic Window Performanceand economic benefits of electrochromic smart windows,"

  13. THERMAL PERFORMANCE OF INSULATING WINDOW SYSTEMS

    E-Print Network [OSTI]

    Selkowitz, Stephen E.

    2011-01-01T23:59:59.000Z

    these windows incorporating hear mirror films are staticS. , "Thin Film Coatings for Energy Efficient Windows", LBLglazed windows with single and double plastic film inserts

  14. Energy Efficient Electrochromic Windows Incorporating Ionic Liquids

    SciTech Connect (OSTI)

    Cheri Boykin; James Finley; Donald Anthony; Julianna Knowles; Richard Markovic; Michael Buchanan; Mary Ann Fuhry; Lisa Perrine

    2008-11-30T23:59:59.000Z

    One approach to increasing the energy efficiency of windows is to control the amount of solar radiation transmitted through a window by using electrochromic technology. What is unique about this project is that the electrochromic is based on the reduction/oxidation reactions of cathodic and anodic organic semi-conducting polymers using room temperature ionic liquids as ion transport electrolytes. It is believed that these types of coatings would be a lower cost alternative to traditional all inorganic thin film based electrochromic technologies. Although there are patents1 based on the proposed technology, it has never been reduced to practice and thoroughly evaluated (i.e. durability and performance) in a window application. We demonstrate that by using organic semi-conductive polymers, specific bands of the solar spectrum (specifically visible and near infrared) can be targeted for electrochemical variable transmittance responsiveness. In addition, when the technology is incorporated into an insulating glass unit, the energy parameters such as the solar heat gain coefficient and the light to solar gain ratio are improved over that of a typical insulating glass unit comprised of glass with a low emissivity coating. A minimum of {approx}0.02 quads of energy savings per year with a reduction of carbon emissions for electricity of {approx}320 MKg/yr benefit is achieved over that of a typical insulating glass unit including a double silver low-E coating. Note that these values include a penalty in the heating season. If this penalty is removed (i.e. in southern climates or commercial structures where cooling is predominate year-round) a maximum energy savings of {approx}0.05 quad per year and {approx}801 MKg/yr can be achieved over that of a typical insulating glass unit including a double silver low-E coating. In its current state, the technology is not durable enough for an exterior window application. The primary downfall is that the redox chemistry fails to recover to a bleached state upon exposure to heat and solar radiation while being cycled over time from the bleached to the dark state. Most likely the polymers are undergoing degradation reactions which are accelerated by heat and solar exposure while in either the reduced or oxidized states and the performance of the polymers is greatly reduced over time. For this technology to succeed in an exterior window application, there needs to be more work done to understand the degradation of the polymers under real-life application conditions such as elevated temperatures and solar exposure so that recommendations for improvements in to the overall system can be made. This will be the key to utilizing this type of technology in any future real-life applications.

  15. Design and prototype of a partial window replacement to improve the energy efficiency of 90-year-old MIT buildings

    E-Print Network [OSTI]

    Chen, YunJa

    2007-01-01T23:59:59.000Z

    The existing windows of the 90-year-old buildings on the main MIT campus are not energy efficient and compromise comfort levels. The single panes of glass allow too much heat transfer and solar heat gain. In addition, the ...

  16. Window Replacement, Rehabilitation, & Repair Guides - Building...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Window Replacement, Rehabilitation, & Repair Guides - Building America Top Innovation Window Replacement, Rehabilitation, & Repair Guides - Building America Top Innovation Effec...

  17. Windows | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of InspectorConcentrating SolarElectric Coop,SaveWhiskey Flats Geothermal Areaarticle is a stub.Wind)WindWindows

  18. Window Daylighting Demo

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy Usage »of| Department ofDepartment ofAnnouncementAugust 30,PowerJuneenabledandWindow

  19. Subject Responses to Electrochromic Windows

    SciTech Connect (OSTI)

    Clear, Robert; Inkarojrit, Vorapat; Lee, Eleanor

    2006-03-03T23:59:59.000Z

    Forty-three subjects worked in a private office with switchable electrochromic windows, manually-operated Venetian blinds, and dimmable fluorescent lights. The electrochromic window had a visible transmittance range of approximately 3-60%. Analysis of subject responses and physical data collected during the work sessions showed that the electrochromic windows reduced the incidence of glare compared to working under a fixed transmittance (60%) condition. Subjects used the Venetian blinds less often and preferred the variable transmittance condition, but used slightly more electric lighting with it than they did when window transmittance was fixed.

  20. A window on urban sustainability

    SciTech Connect (OSTI)

    Stigt, Rien van, E-mail: rien.vanstigt@hu.nl [Research Center for Technology and Innovation, Utrecht University of Applied Sciences, P.O. Box 182, 3500 AD Utrecht (Netherlands); Driessen, Peter P.J., E-mail: p.driessen@uu.nl [Copernicus Institute of Sustainable Development, Faculty of Geosciences, Utrecht University, P.O. Box 80.115, 3508 TC Utrecht (Netherlands); Spit, Tejo J.M., E-mail: T.J.M.Spit@uu.nl [Department of Human Geography and Spatial Planning, Faculty of Geosciences, Utrecht University, P.O. Box 80.115, 3508 TC Utrecht (Netherlands)

    2013-09-15T23:59:59.000Z

    Sustainable urban development requires the integration of environmental interests in urban planning. Although various methods of environmental assessment have been developed, plan outcomes are often disappointing due to the complex nature of decision-making in urban planning, which takes place in multiple arenas within multiple policy networks involving diverse stakeholders. We argue that the concept of ‘decision windows’ can structure this seemingly chaotic chain of interrelated decisions. First, explicitly considering the dynamics of the decision-making process, we further conceptualized decision windows as moments in an intricate web of substantively connected deliberative processes where issues are reframed within a decision-making arena, and interests may be linked within and across arenas. Adopting this perspective in two case studies, we then explored how decision windows arise, which factors determine their effectiveness and how their occurrence can be influenced so as to arrive at more sustainable solutions. We conclude that the integration of environmental interests in urban planning is highly dependent on the ability of the professionals involved to recognize and manipulate decision windows. Finally, we explore how decision windows may be opened. -- Highlights: • Decision-making about sustainable urban development occurs in networks. • The concept of ‘decision windows’ was further elaborated. • Decision windows help understand how environmental interests enter decision-making. • Decision windows can, to some extent, be influenced.

  1. Evaluation of Low-E Storm Windows in the PNNL Lab Homes

    SciTech Connect (OSTI)

    Knox, Jake R.; Widder, Sarah H.

    2014-05-31T23:59:59.000Z

    This study examines the performance of exterior and interior low-e storm panels with a controlled whole home experimental design using PNNL's Lab Homes. Summing the estimated annual average heating and cooling savings, the installation of low-e storm panels resulted in approximately 10% annual energy savings. The results of the experiment will be used to determine and validate performance of low-e storm windows over double pane clear glass windows in a whole home setting.

  2. Test for Modeling Windows in DOE 2.1E for Comparing the Window Library with the Shading Coefficient Method for a Single-Family Residence in Texas

    E-Print Network [OSTI]

    Kim, S.; Haberl, J. S.

    2008-07-18T23:59:59.000Z

    . The window simulation tests are performed using single-pane, double-pane, and low-e glass on two standard DOE 2.1E single-family house models: 1) the model which has the R-value for wall, roof and floor according to 2000 IECC (Quick Wall), and 2) the model...

  3. Establishment of a Rating Program for Pre- and Post-Fabricated Windows

    SciTech Connect (OSTI)

    Parker, Graham B.; Mapes, Terry S.; Shah, B.; Bloyd, Cary N.

    2011-08-01T23:59:59.000Z

    This document was prepared to support the Smart Buildings-Material Testing and Rating Centres (SB-2) activity of the Asia-Pacific Economic Cooperation (APEC) Energy Smart Communities Initiative (ESCI). The ESCI was put forward by APEC Leaders at the 2010 meeting in Japan. APEC is the premier forum for facilitating economic growth, cooperation, trade and investment in the Asia-Pacific region. This document addresses the testing and certification of building products and equipment to support building energy codes, focusing specifically on energy-efficient factory-built windows. It sets forth a proposed structure for an APEC economy to establish a testing, rating, certification, and labeling program for efficient factory-built windows. In the context of this document, efficient windows would be windows made with insulating glass (IG) and an efficient frame assembly. The minimum efficiency metric (or thermal performance) for these windows is not quantified in this document and would generally be established by a governmental agency.

  4. High-Efficiency Window Air Conditioners - Building America Top...

    Broader source: Energy.gov (indexed) [DOE]

    Window Air Conditioners - Building America Top Innovation This photo shows a window air conditioning unit in place in a window frame. Window air conditioners are inexpensive,...

  5. Key Elements of and Materials Performance Targets for Highly Insulating Window Frames

    SciTech Connect (OSTI)

    Gustavsen, Arild; Grynning, Steinar; Arasteh, Dariush; Jelle, Bjorn Petter; Goudey, Howdy

    2011-03-28T23:59:59.000Z

    The thermal performance of windows is important for energy efficient buildings. Windows typically account for about 30-50 percent of the transmission losses though the building envelope, even if their area fraction of the envelope is far less. The reason for this can be found by comparing the thermal transmittance (U-factor) of windows to the U-factor of their opaque counterparts (wall, roof and floor constructions). In well insulated buildings the U-factor of walls, roofs an floors can be between 0.1-0.2 W/(m2K). The best windows have U-values of about 0.7-1.0. It is therefore obvious that the U-factor of windows needs to be reduced, even though looking at the whole energy balance for windows (i.e. solar gains minus transmission losses) makes the picture more complex.In high performance windows the frame design and material use is of utmost importance, as the frame performance is usually the limiting factor for reducing the total window U-factor further. This paper describes simulation studies analyzing the effects on frame and edge-of-glass U-factors of different surface emissivities as well as frame material and spacer conductivities. The goal of this work is to define materials research targets for window frame components that will result in better frame thermal performance than is exhibited by the best products available on the market today.

  6. Transparency: it's not just for windows

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    for windows Transparency: it's not just for windows Los Alamos National Laboratory's database of environmental monitoring data is now directly viewable by the public. March 20,...

  7. Applicability of Solar Airflow Windows

    E-Print Network [OSTI]

    Hamed, M. S.; Friedrich, K.; Razaqpur, G.; Foo, S.

    2010-01-01T23:59:59.000Z

    Accurate prediction of the performance of Solar Air Windows (SAWs) operating in various climates under real conditions has not been investigated. This paper reports the results of numerical simulations of SAWs carried out using ANSYS-CFX considering...

  8. Close Window MARCH 3, 2003

    E-Print Network [OSTI]

    Close Window MARCH 3, 2003 DEVELOPMENTS TO WATCH Killing Superbugs from Within A common moth may the surface of a flat, thin-film mirror. But these deformable mirror lenses are small--only a few inches

  9. CMU-ITC-86-045 , Windowing

    E-Print Network [OSTI]

    on window-manager style graphics systems using the Tek termi- nals, inspired by some film Alan Kay showedCMU-ITC-86-045 , Windowing Systems , Implementations #12;#12;Window System Implementations Denver ABSTRACT Notes for a course given at the 1986 Winter Usenix meeting in Denver, CO. It covers window systems

  10. Extending the X Window System

    SciTech Connect (OSTI)

    Brenkosh, J.P.

    1993-12-23T23:59:59.000Z

    The X Window System was originally developed in 1984 at Massachusetts Institute of Technology. It provides client-server computing functionality and also facilitates the establishment of a distributed computing environment. Since its inception the X Window System has undergone many enhancements. Despite these enhancements there will always be a functionality desired in the standard released version of X that is not supported or commercially or academically available. The developers of the X Window System have designed it in such a way that it is possible to add functionality that is not included in the standard release. This is called an extension. Extensions are one method used to develop a customized version of the X Window System to support a specialized application. This report presents the mechanics of adding an extension and examines a particular extension that was developed at Sandia National Laboratories to support data compression in X Windows which was one aspect of the Desktop Video and Collaborative Engineering Laboratory Directed Research and Development (LDRD).

  11. Field Evaluation of Highly Insulating Windows in the Lab Homes: Winter Experiment

    SciTech Connect (OSTI)

    Parker, Graham B.; Widder, Sarah H.; Bauman, Nathan N.

    2012-06-01T23:59:59.000Z

    This field evaluation of highly insulating windows was undertaken in a matched pair of 'Lab Homes' located on the Pacific Northwest National Laboratory (PNNL) campus during the 2012 winter heating season. Improving the insulation and solar heat gain characteristics of a home's windows has the potential to significantly improve the home's building envelope and overall thermal performance by reducing heat loss (in the winter), and cooling loss and solar heat gain (in the summer) through the windows. A high quality installation and/or window retrofit will also minimize or reduce air leakage through the window cavity and thus also contribute to reduced heat loss in the winter and cooling loss in the summer. These improvements all contribute to decreasing overall annual home energy use. Occupant comfort (non-quantifiable) can also be increased by minimizing or eliminating the cold 'draft' (temperature) many residents experience at or near window surfaces that are at a noticeably lower temperature than the room air temperature. Lastly, although not measured in this experiment, highly insulating windows (triple-pane in this experiment) also have the potential to significantly reduce the noise transmittance through windows compared to standard double-pane windows. The metered data taken in the Lab Homes and data analysis presented here represent 70 days of data taken during the 2012 heating season. As such, the savings from highly insulating windows in the experimental home (Lab Home B) compared to the standard double-pane clear glass windows in the baseline home (Lab Home A) are only a portion of the energy savings expected from a year-long experiment that would include a cooling season. The cooling season experiment will take place in the homes in the summer of 2012, and results of that experiment will be reported in a subsequent report available to all stakeholders.

  12. Expert Meeting Report: Windows Options for New and Existing Homes

    SciTech Connect (OSTI)

    Ojczyk, C.; Carmody, J.; Haglund, K.

    2013-05-01T23:59:59.000Z

    The NorthernSTAR Building America Partnership held an Expert Meeting on Windows Options for New and Existing Homes on November 14, 2011 at the Nolte Building on the campus of the University of Minnesota in Minneapolis, MN. Featured speakers included John Carmody and Pat Huelman of the University of Minnesota, Charlie Curcija of Lawrence Berkeley National Laboratory, Jim Larson of Cardinal Glass Industries, Peter Yost of Building Green, Peter Baker of Building Science Corporation, and Theresa Weston of Du Pont Innovations. Audience participation was actively encouraged during each presentation to uncover need and promote dialog among researchers and industry professionals.

  13. Tips: Windows | Department of Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas ConchasPassiveSubmittedStatusButler Tina Butler Tina-Butler.jpgLightingWindows Tips: Windows

  14. Research Needs: Glass Solar Reflectance and Vinyl Siding

    SciTech Connect (OSTI)

    Hart, Robert; Curcija, Charlie; Arasteh, Dariush; Goudey, Howdy; Kohler, Christian; Selkowitz, Stephen

    2011-07-07T23:59:59.000Z

    The subject of glass solar reflectance and its contribution to permanent vinyl siding distortion has not been extensively studied, and some phenomena are not yet well understood. This white paper presents what is known regarding the issue and identifies where more research is needed. Three primary topics are discussed: environmental factors that control the transfer of heat to and from the siding surface; vinyl siding properties that may affect heat build-up and permanent distortion; and factors that determine the properties of reflected solar radiation from glass surfaces, including insulating window glass. Further research is needed to fully characterize the conditions associated with siding distortion, the scope of the problem, physical properties of vinyl siding, insulating window glass reflection characteristics, and possible mitigation or prevention strategies.

  15. Thermal Performance Impacts of Center-of-Glass Deflections in Installed Insulating

    E-Print Network [OSTI]

    LBNL-5800E Thermal Performance Impacts of Center-of- Glass Deflections in Installed Insulating Laboratory Windows and Envelope Materials Group Building Technology and Urban Systems Department: temperature difference Thermal Performance Impacts of Center-of-Glass Deflections in Installed Insulating

  16. Rolling, Rolling, Rolling: Roller Window Shades | Department...

    Broader source: Energy.gov (indexed) [DOE]

    anyway, even if our windows were of the highest efficiency. One of my colleagues in a solar energy group I belonged to was a distributor of a high R-value quilted roller window...

  17. AIR LEAKAGE OF NEWLY INSTALLED RESIDENTIAL WINDOWS

    E-Print Network [OSTI]

    Weidt, John

    2013-01-01T23:59:59.000Z

    Tables 2.0.2a 2.0.2b PAGE Air Leakage Through Sash/FrameOperation Types . . . . . Air Leakage of Installed WindowsComparison of Window Types Air Leakage Performance of

  18. IT Administrator's Guide to Using Windows Vista

    E-Print Network [OSTI]

    Narasayya, Vivek

    IT Administrator's Guide to Using Windows Vista® for Sustainable IT Success Published: February Administrator's Guide to Using Windows Vista for Sustainable IT Success Contents Executive Summary ................................................................................................ 3 Sustainable IT Goals

  19. RUGGED CERAMIC WINDOW FOR RF APPLICATIONS

    SciTech Connect (OSTI)

    MIKE NEUBAUER

    2012-11-01T23:59:59.000Z

    High-current RF cavities that are needed for many accelerator applications are often limited by the power transmission capability of the pressure barriers (windows) that separate the cavity from the power source. Most efforts to improve RF window design have focused on alumina ceramic, the most popular historical choice, and have not taken advantage of new materials. Alternative window materials have been investigated using a novel Merit Factor comparison and likely candidates have been tested for the material properties which will enable construction in the self-matched window configuration. Window assemblies have also been modeled and fabricated using compressed window techniques which have proven to increase the power handling capability of waveguide windows. Candidate materials have been chosen to be used in fabricating a window for high power testing at Thomas Jefferson National Accelerator Facility.

  20. An analysis of residential window waterproofing systems

    E-Print Network [OSTI]

    Parsons, Austin, 1959-

    2004-01-01T23:59:59.000Z

    The prevalence of vinyl nail-on windows in the North American new home construction market has prompted ASTM International to write ASTM E2112-01 "Standard Practice for Installation of Exterior Windows, Doors and Skylights". ...

  1. Simulating Complex Window Systems using BSDF Data

    E-Print Network [OSTI]

    Konstantoglou, Maria

    2011-01-01T23:59:59.000Z

    Daylighting, Design tools and methods INTRODUCTION Simulations enable designers and engineers to evaluate and select the best available window solutions

  2. A Design Guide for Early-Market Electrochromic Windows

    E-Print Network [OSTI]

    2006-01-01T23:59:59.000Z

    Guide for Early-Market Electrochromic Windows. CaliforniaGuide for Early-Market Electrochromic Windows. CaliforniaGUIDE FOR EARLY-MARKET ELECTROCHROMIC WINDOWS Prepared For:

  3. A Design Guide for Early-Market Electrochromic Windows

    E-Print Network [OSTI]

    2006-01-01T23:59:59.000Z

    Office worker preferences of electrochromic windows: a pilotDetails for an Electrochromic Window Wall Attached arethe performance of the electrochromic windows. Proceedings

  4. Windows and Building Envelope Research and Development Roadmap...

    Broader source: Energy.gov (indexed) [DOE]

    Windows and Building Envelope Research and Development Roadmap Windows and Building Envelope Research and Development Roadmap Cover of windows and envelope report, depicting a...

  5. Highly Insulating Residential Windows Using Smart Automated Shading...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Highly Insulating Residential Windows Using Smart Automated Shading Highly Insulating Residential Windows Using Smart Automated Shading Addthis 1 of 3 Residential Smart Window with...

  6. Performance Criteria for Residential Zero Energy Windows

    E-Print Network [OSTI]

    Arasteh, Dariush; Goudey, Howdy; Huang, Joe; Kohler, Christian; Mitchell, Robin

    2006-01-01T23:59:59.000Z

    energy use data were collected for each city, to provide information regarding the predominant glass area

  7. Rigid thin windows for vacuum applications

    DOE Patents [OSTI]

    Meyer, Glenn Allyn (Danville, CA); Ciarlo, Dino R. (Livermore, CA); Myers, Booth Richard (Livermore, CA); Chen, Hao-Lin (Lafayette, CA); Wakalopulos, George (Pacific Palisades, CA)

    1999-01-01T23:59:59.000Z

    A thin window that stands off atmospheric pressure is fabricated using photolithographic and wet chemical etching techniques and comprises at least two layers: an etch stop layer and a protective barrier layer. The window structure also comprises a series of support ribs running the width of the window. The windows are typically made of boron-doped silicon and silicon nitride and are useful in instruments such as electron beam guns and x-ray detectors. In an electron beam gun, the window does not impede the electrons and has demonstrated outstanding gun performance and survivability during the gun tube manufacturing process.

  8. CRYSTALLIZATION IN MULTICOMPONENT GLASSES

    SciTech Connect (OSTI)

    KRUGER AA; HRMA PR

    2009-10-08T23:59:59.000Z

    In glass processing situations involving glass crystallization, various crystalline forms nucleate, grow, and dissolve, typically in a nonuniform temperature field of molten glass subjected to convection. Nuclear waste glasses are remarkable examples of multicomponent vitrified mixtures involving partial crystallization. In the glass melter, crystals form and dissolve during batch-to-glass conversion, melter processing, and product cooling. Crystals often agglomerate and sink, and they may settle at the melter bottom. Within the body of cooling glass, multiple phases crystallize in a non-uniform time-dependent temperature field. Self-organizing periodic distribution (the Liesegnang effect) is common. Various crystallization phenomena that occur in glass making are reviewed.

  9. Window Types | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy UsageAUDITVehiclesTankless or Demand-TypeWelcome toFarm Growth Through theofWindow

  10. Stanek Windows | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia:FAQ < RAPID Jump to:Seadov Pty Ltd JumpGTZHolland,0162112°,St. Charles isStallings,StandardizedStanek Windows

  11. Glass-silicon column

    DOE Patents [OSTI]

    Yu, Conrad M.

    2003-12-30T23:59:59.000Z

    A glass-silicon column that can operate in temperature variations between room temperature and about 450.degree. C. The glass-silicon column includes large area glass, such as a thin Corning 7740 boron-silicate glass bonded to a silicon wafer, with an electrode embedded in or mounted on glass of the column, and with a self alignment silicon post/glass hole structure. The glass/silicon components are bonded, for example be anodic bonding. In one embodiment, the column includes two outer layers of silicon each bonded to an inner layer of glass, with an electrode imbedded between the layers of glass, and with at least one self alignment hole and post arrangement. The electrode functions as a column heater, and one glass/silicon component is provided with a number of flow channels adjacent the bonded surfaces.

  12. Hybrid window layer for photovoltaic cells

    DOE Patents [OSTI]

    Deng, Xunming (Syvania, OH); Liao, Xianbo (Toledo, OH); Du, Wenhui (Toledo, OH)

    2011-10-04T23:59:59.000Z

    A novel photovoltaic solar cell and method of making the same are disclosed. The solar cell includes: at least one absorber layer which could either be a lightly doped layer or an undoped layer, and at least a doped window-layers which comprise at least two sub-window-layers. The first sub-window-layer, which is next to the absorber-layer, is deposited to form desirable junction with the absorber-layer. The second sub-window-layer, which is next to the first sub-window-layer, but not in direct contact with the absorber-layer, is deposited in order to have transmission higher than the first-sub-window-layer.

  13. Hybrid window layer for photovoltaic cells

    DOE Patents [OSTI]

    Deng, Xunming (Syvania, OH)

    2010-02-23T23:59:59.000Z

    A novel photovoltaic solar cell and method of making the same are disclosed. The solar cell includes: at least one absorber layer which could either be a lightly doped layer or an undoped layer, and at least a doped window-layers which comprise at least two sub-window-layers. The first sub-window-layer, which is next to the absorber-layer, is deposited to form desirable junction with the absorber-layer. The second sub-window-layer, which is next to the first sub-window-layer, but not in direct contact with the absorber-layer, is deposited in order to have transmission higher than the first-sub-window-layer.

  14. Hybrid window layer for photovoltaic cells

    DOE Patents [OSTI]

    Deng, Xunming (Sylvania, OH); Liao, Xianbo (Toledo, OH); Du, Wenhui (Toledo, OH)

    2011-02-01T23:59:59.000Z

    A novel photovoltaic solar cell and method of making the same are disclosed. The solar cell includes: at least one absorber layer which could either be a lightly doped layer or an undoped layer, and at least a doped window-layers which comprise at least two sub-window-layers. The first sub-window-layer, which is next to the absorber-layer, is deposited to form desirable junction with the absorber-layer. The second sub-window-layer, which is next to the first sub-window-layer, but not in direct contact with the absorber-layer, is deposited in order to have transmission higher than the first-sub-window-layer.

  15. THERMAL PERFORMANCE OF INSULATING WINDOW SYSTEMS

    E-Print Network [OSTI]

    Selkowitz, Stephen E.

    2011-01-01T23:59:59.000Z

    Efficient Use of Energy, New York (1975). Glaser, V.H.J. , "Energy Transport Control in Window Systems", Report ETR-1277-2, Stony Brook, New York, (

  16. A Review of Electrochromic Window Performance Factors

    E-Print Network [OSTI]

    Selkowitz Ed, S.E.

    2010-01-01T23:59:59.000Z

    influence the market acceptance of electrochromic windowsfor the eventual market success of electrochromic windows inearly niche market might consist of adding an electrochromic

  17. Measure Guideline: Window Repair, Rehabilitation, and Replacement

    SciTech Connect (OSTI)

    Baker, P.

    2012-12-01T23:59:59.000Z

    This measure guideline provides information and guidance on rehabilitating, retrofitting, and replacing existing window assemblies in residential construction. The intent is to provide information regarding means and methods to improve the energy and comfort performance of existing wood window assemblies in a way that takes into consideration component durability, in-service operation, and long term performance of the strategies.

  18. Windows Enterprise Design Master Directory Sources

    E-Print Network [OSTI]

    Mayfield, John

    Windows Enterprise Design Master Directory Sources April 2, 2014 Active Directory information be to use a Microsoft "Outlook" email client to query Active Directory for someone with a certain "last name in Windows Active Directory. It is important the information correctly reflects your current name

  19. Solar Window Technology for BIPV or

    E-Print Network [OSTI]

    Painter, Kevin

    Solar Window Technology for BIPV or BAPV Energy Systems Problem this technology solves: Using of Solar energy considerably, photovoltaic or PV material is still a major $ cost/unit of energy produced a novel high efficiency concentrator design, this static "Solar Window" system is such that it allows

  20. ITP Glass: Industrial Glass Bandwidth Analysis Final Report,...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy and Environmental Profile of the U.S. Glass Industry; April, 2002 ITP Glass: Glass Industry Technology Roadmap; April 2002 ITP Glass: A Clear Vision for a Bright Future...

  1. ITP Glass: Glass Industry of the Future: Energy and Environmental...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Glass Industry of the Future: Energy and Environmental Profile of the U.S. Glass Industry; April, 2002 ITP Glass: Glass Industry of the Future: Energy and Environmental Profile of...

  2. Electrochromic windows for commercial buildings: Monitored results from a full-scale testbed

    E-Print Network [OSTI]

    Lee, Eleanor S.; DiBartolomeo, Dennis L.; Selkowitz, Stephen E.

    2000-01-01T23:59:59.000Z

    lifetime prediction of electrochromic windows for buildingsenergy performance of electrochromic windows. ” Proceedingsin the Proceedings. Electrochromic Windows for Commercial

  3. Lighting energy savings potential of split-pane electrochromic windows controlled for daylighting with visual comfort

    E-Print Network [OSTI]

    Fernandes, Luis

    2014-01-01T23:59:59.000Z

    Energy Performance of Electrochromic Windows Controlled forenergy performance of electrochromic windows. Proceedingssignal for daylight (electrochromic window, no overhang).

  4. Window Manufacturer Sees Business Surge As Weatherization Supplier...

    Broader source: Energy.gov (indexed) [DOE]

    of the aluminum windows they're replacing - the U-value is the measure of the rate of heat loss or gain through a window. The lower the U-value, the better a window's...

  5. U-028: Microsoft Windows win32k.sys TrueType Font Parsing Vulnerabilit...

    Broader source: Energy.gov (indexed) [DOE]

    Parsing Vulnerability. PLATFORM: Microsoft Windows 7 Microsoft Windows Server 2003 Datacenter Edition Microsoft Windows Server 2003 Enterprise Edition Microsoft Windows Server...

  6. Effects of Overhangs on the Performance of Electrochromic Windows

    E-Print Network [OSTI]

    Tavil, Aslihan; Lee, Eleanor S.

    2005-01-01T23:59:59.000Z

    issues for large-area electrochromic windows in commercialenergy performance of electrochromic windows controlled forwindows.lbl.gov/comm_perf/Electrochromic/ Winkelmann, F.C. ,

  7. June 1998Program Description Windows and Daylighting Group

    E-Print Network [OSTI]

    June 1998Program Description THERM 2.0 Windows and Daylighting Group Building Technologies, and Dariush Arasteh Windows and Daylighting Group Building Technologies Department Environmental Energy

  8. Assessment of Energy Impact of Window Technologies for Commercial Buildings

    E-Print Network [OSTI]

    Hong, Tianzhen

    2014-01-01T23:59:59.000Z

    1.2 quads. Future window technologies offer energy savingsImpact of Window Technologies for Commercial BuildingsEnvironmental Energy Technologies Division October 2009 This

  9. 700 MHz window R & D at LBNL

    E-Print Network [OSTI]

    Rimmer, R.A.; Koehler, G.; Saleh, T.; Weidenbach, R.

    2000-01-01T23:59:59.000Z

    LBNL-47939 LAUR 01-2574 CBP tech230 700 MHz Window R&D at LBNL R. Rimmer, G. Koehler, T.describes the R&D activities at LBNL under contract # 06261-

  10. Occupant Response to Window Control Signaling Systems

    E-Print Network [OSTI]

    Ackerly, Katherine

    2012-01-01T23:59:59.000Z

    my window it will waste energy.  Even so I open the windowthe windown wouldn’t waste energy. ” MS Thesis, Dept. ofthe potential for energy waste and balancing issues.  

  11. Electrochromic sun control coverings for windows

    SciTech Connect (OSTI)

    Benson, D K; Tracy, C E

    1990-04-01T23:59:59.000Z

    The 2 billion square meters (m{sup 2}) of building windows in the United States cause a national energy drain almost as large as the energy supply of the Alaskan oil pipeline. Unlike the pipeline, the drain of energy through windows will continue well into the 21st century. A part of this energy drain is due to unwanted sun gain through windows. This is a problem throughout the country in commercial buildings because they generally require air conditioning even in cold climates. New commercial windows create an additional 1600 MW demand for peak electric power in the United States each year. Sun control films, widely used in new windows and as retrofits to old windows, help to mitigate this problem. However, conventional, static solar control films also block sunlight when it is wanted for warmth and daylighting. New electrochromic, switchable, sun-gain-control films now under development will provide more nearly optimal and automatic sun control for added comfort, decreased building operating expense, and greater energy saving. Switchable, electrochromic films can be deposited on polymers at high speeds by plasma enhanced chemical vapor deposition (PECVD) in a process that may be suitable for roll coating. This paper describes the electrochromic coatings and the PECVD processes, and speculates about their adaptability to high-speed roll coating. 8 refs., 3 figs.

  12. Transforming the market for residential windows: design considerations for DOE's Efficient Window Collaborative

    SciTech Connect (OSTI)

    Eto, J.; Arasteh, D.; Selkowitz, S.

    1998-08-01T23:59:59.000Z

    Market adoption of recent, commercially available technological advances that improve the energy performance of windows will lead to immediate economic and energy savings benefits to the nation. This paper is a scoping study intended to inform the design of a major DOE initiative to accelerate market adoption of these windows in the residential sector. We describe the structure of the US residential window market and the interests of the various market players. We then briefly review five recent market transformation initiatives. Finally, we summarize our findings in a list of considerations we believe will be important for the DOE's initiative to transform the US residential window market.

  13. Assessment of Energy Impact of Window Technologies for Commercial Buildings

    E-Print Network [OSTI]

    Hong, Tianzhen

    2014-01-01T23:59:59.000Z

    electrochromic windows were technically successful, but it will take a number of years for significant market

  14. Diamond turning of glass

    SciTech Connect (OSTI)

    Blackley, W.S.; Scattergood, R.O.

    1988-12-01T23:59:59.000Z

    A new research initiative will be undertaken to investigate the critical cutting depth concepts for single point diamond turning of brittle, amorphous materials. Inorganic glasses and a brittle, thermoset polymer (organic glass) are the principal candidate materials. Interrupted cutting tests similar to those done in earlier research are Ge and Si crystals will be made to obtain critical depth values as a function of machining parameters. The results will provide systematic data with which to assess machining performance on glasses and amorphous materials

  15. Cosmic Microwave Background Anisotropy Window Functions Revisited

    E-Print Network [OSTI]

    Lloyd Knox

    1999-09-28T23:59:59.000Z

    The primary results of most observations of cosmic microwave background (CMB) anisotropy are estimates of the angular power spectrum averaged through some broad band, called band-powers. These estimates are in turn what are used to produce constraints on cosmological parameters due to all CMB observations. Essential to this estimation of cosmological parameters is the calculation of the expected band-power for a given experiment, given a theoretical power spectrum. Here we derive the "band power" window function which should be used for this calculation, and point out that it is not equivalent to the window function used to calculate the variance. This important distinction has been absent from much of the literature: the variance window function is often used as the band-power window function. We discuss the validity of this assumed equivalence, the role of window functions for experiments that constrain the power in {\\it multiple} bands, and summarize a prescription for reporting experimental results. The analysis methods detailed here are applied in a companion paper to three years of data from the Medium Scale Anisotropy Measurement.

  16. Rare Earth Phosphate Glass and Glass-Ceramic Proton Conductors

    E-Print Network [OSTI]

    De Jonghe, Lutgard C.

    2010-01-01T23:59:59.000Z

    300-500°C. Doping rare earth phosphate glasses with Ce, andRare Earth Phosphate Glass and Glass-Ceramic Protonconductivity of alkaline-earth doped rare earth phosphate

  17. Empirical assessment of a prismatic daylight-redirecting window film in a full-scale office testbed

    SciTech Connect (OSTI)

    Thanachareonkit, Anothai; Lee, Eleanor S.; McNeil, Andrew

    2013-08-31T23:59:59.000Z

    Daylight redirecting systems with vertical windows have the potential to offset lighting energy use in deep perimeter zones. Microstructured prismatic window films can be manufactured using low-cost, roll-to-roll fabrication methods and adhered to the inside surface of existing windows as a retrofit measure or installed as a replacement insulating glass unit in the clerestory portion of the window wall. A clear film patterned with linear, 50-250 micrometer high, four-sided asymmetrical prisms was fabricated and installed in the south-facing, clerestory low-e, clear glazed windows of a full-scale testbed facility. Views through the film were distorted. The film was evaluated in a sunny climate over a two-year period to gauge daylighting and visual comfort performance. The daylighting aperture was small (window-towall ratio of 0.18) and the lower windows were blocked off to isolate the evaluation to the window film. Workplane illuminance measurements were made in the 4.6 m (15 ft) deep room furnished as a private office. Analysis of discomfort glare was conducted using high dynamic range imaging coupled with the evalglare software tool, which computes the daylight glare probability and other metrics used to evaluate visual discomfort. The window film was found to result in perceptible levels of discomfort glare on clear sunny days from the most conservative view point in the rear of the room looking toward the window. Daylight illuminance levels at the rear of the room were significantly increased above the reference window condition, which was defined as the same glazed clerestory window but with an interior Venetian blind (slat angle set to the cut-off angle), for the equinox to winter solstice period on clear sunny days. For partly cloudy and overcast sky conditions, daylight levels were improved slightly. To reduce glare, the daylighting film was coupled with a diffusing film in an insulating glazing unit. The diffusing film retained the directionality of the redirected light spreading it within a small range of outgoing angles. This solution was found to reduce glare to imperceptible levels while retaining for the most part the illuminance levels achieved solely by the daylighting film.

  18. Apparatus for insulating windows and the like

    DOE Patents [OSTI]

    Mitchell, Robert A. (R.D. #1, Box 462-A, Voorheesville, NY 12186)

    1984-01-01T23:59:59.000Z

    Apparatus for insulating window openings through walls and the like includes a thermal shutter, a rail for mounting the shutter adjacent to the window opening and a coupling for connecting the shutter to the rail. The thermal shutter includes an insulated panel adhered to frame members which surround the periphery of the panel. The frame members include a hard portion for providing the frame and a soft portion for providing a seal with that portion of the wall adjacent to the periphery of the opening. The coupling means is preferably integral with the attachment rail. According to a preferred embodiment, the coupling means includes a continuous hinge of reduced thickness. The thermal shutter can be permanently attached, hinged, bi-folded, or sliding with respect to the window and wall. A distribution method is to market the apparatus in "kit" form.

  19. Energy-Efficient Windows | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"ClickPipelinesProvedDecember 2005DepartmentDecember 2011District |Department ofEnergy andWindowWindows

  20. Defense HLW Glass Degradation Model

    SciTech Connect (OSTI)

    D. Strachan

    2004-10-20T23:59:59.000Z

    The purpose of this report is to document the development of a model for calculating the release rate for radionuclides and other key elements from high-level radioactive waste (HLW) glasses under exposure conditions relevant to the performance of the repository. Several glass compositions are planned for the repository, some of which have yet to be identified (i.e., glasses from Hanford and Idaho National Engineering and Environmental Laboratory). The mechanism for glass dissolution is the same for these glasses and the glasses yet to be developed for the disposal of DOE wastes. All of these glasses will be of a quality consistent with the glasses used to develop this report.

  1. The Current T2K Beam Window

    E-Print Network [OSTI]

    McDonald, Kirk

    Downstream Helium velocity 5 m/s Heat transfer coefficient 150 W/m2K #12;Helium flow grooves He in He out at KEK (via Oak Ridge via PSI). #12;Assembled Window #12;Remote Handling #12;Remote handling Monitor Chamber (Canada) Target Station (Japan) #12;Remote installation #12;Stress analysis and upgrade potential

  2. Occupant Response to Window Control Signaling Systems

    E-Print Network [OSTI]

    Ackerly, Katherine

    2012-01-01T23:59:59.000Z

    preventing energy waste during the red light mode is a moregreen lights was installed to help avoid energy waste, or inlight means that energy is being used to modify the temparature inside and therefore if I open my window it will waste energy.  

  3. Baseline LAW Glass Formulation Testing

    SciTech Connect (OSTI)

    Kruger, Albert A. [USDOE Office of River Protection, Richland, WA (United States); Mooers, Cavin [The Catholic University of America, Washington, DC (United States). Vitreous State Lab.; Bazemore, Gina [The Catholic University of America, Washington, DC (United States). Vitreous State Lab; Pegg, Ian L. [The Catholic University of America, Washington, DC (United States). Vitreous State Lab; Hight, Kenneth [The Catholic University of America, Washington, DC (United States). Vitreous State Lab; Lai, Shan Tao [The Catholic University of America, Washington, DC (United States). Vitreous State Lab; Buechele, Andrew [The Catholic University of America, Washington, DC (United States). Vitreous State Lab; Rielley, Elizabeth [The Catholic University of America, Washington, DC (United States). Vitreous State Lab; Gan, Hao [The Catholic University of America, Washington, DC (United States). Vitreous State Lab; Muller, Isabelle S. [The Catholic University of America, Washington, DC (United States). Vitreous State Lab; Cecil, Richard [The Catholic University of America, Washington, DC (United States). Vitreous State Lab

    2013-06-13T23:59:59.000Z

    The major objective of the baseline glass formulation work was to develop and select glass formulations that are compliant with contractual and processing requirements for each of the LAW waste streams. Other objectives of the work included preparation and characterization of glasses with respect to the properties of interest, optimization of sulfate loading in the glasses, evaluation of ability to achieve waste loading limits, testing to demonstrate compatibility of glass melts with melter materials of construction, development of glass formulations to support ILAW qualification activities, and identification of glass formulation issues with respect to contract specifications and processing requirements.

  4. Highly Insulating Residential Windows Using Smart Automated Shading...

    Office of Environmental Management (EM)

    The windows will function autonomously and in a networked configuration. Project Impact LBNL is aiming toward a mature market cost increment of 12ft2 of window. LBNL will also...

  5. Energy Efficiency Hits from the Doors (and Windows) | Department...

    Broader source: Energy.gov (indexed) [DOE]

    Energy Efficiency Hits from the Doors (and Windows) Energy Efficiency Hits from the Doors (and Windows) December 5, 2011 - 5:31am Addthis Ernie Tucker Editor, National Renewable...

  6. Modeling Windows in Energy Plus with Simple Performance Indices

    E-Print Network [OSTI]

    Arasteh, Dariush

    2010-01-01T23:59:59.000Z

    that window U-factors include the interior and exterior filmwindows however, Steps 1 and 5 which use interior filmthese film coefficients to a resistance for the solid window

  7. Infrared Thermography Measurements of Window Thermal Test Specimen Surface Temperatures

    E-Print Network [OSTI]

    Infrared Thermography Measurements of Window Thermal Test Specimen Surface Temperatures Brent T Temperatures of Window Specimens: Infrared Thermography Laboratory Measurements Brent T. Griffith1 , Howdy and cold sides, respectively. Surface temperature maps were compiled using an infrared thermographic system

  8. Metallic glass composition

    DOE Patents [OSTI]

    Kroeger, Donald M. (Knoxville, TN); Koch, Carl C. (Raleigh, NC)

    1986-01-01T23:59:59.000Z

    A metallic glass alloy that is either iron-based or nickel-based or based on a mixture of iron and nickel, containing lesser amounts of elements selected from the group boron, silicon carbon and phosphorous to which is added an amount of a ductility enhancing element selected from the group cerium, lanthanum, praseodymium and neodymium sufficient to increase ductility of the metallic glass upon annealing.

  9. Window and Envelope Technologies Overview - 2014 BTO Peer Review...

    Energy Savers [EERE]

    Research and Development Roadmap: Windows and Building Envelope Research & Development Roadmap: Emerging Water Heating Technologies Research & Development Roadmap: Emerging HVAC...

  10. The Impact of Overhang Design on the Performance of Electrochromic Windows

    E-Print Network [OSTI]

    Tavil, Aslihan; Lee, Eleanor S.

    2005-01-01T23:59:59.000Z

    Issues for Large-area Electrochromic Windows in CommercialAnalysis of Prototype Electrochromic Windows”, ASHRAEon the Performance of Electrochromic Windows Asilhan Tavil

  11. The energy-savings potential of electrochromic windows in the US commercial buildings sector

    E-Print Network [OSTI]

    Lee, Eleanor; Yazdanian, Mehry; Selkowitz, Stephen

    2004-01-01T23:59:59.000Z

    Alone Photovoltaic-Powered Electrochromic Smart Window.Subject responses to electrochromic windows. To be publishedAnalysis of Prototype Electrochromic Windows, ASHRAE

  12. End User Impacts of Automated Electrochromic Windows in a Pilot Retrofit Application

    E-Print Network [OSTI]

    Lee, Eleanor S.

    2014-01-01T23:59:59.000Z

    2006. Advancement of electrochromic windows: Final report.User Impacts of Automated Electrochromic Windows in a Pilotenergy performance of electrochromic windows controlled for

  13. AEROSPACE TECHNOLOGY REVIEW FOR LBL WINDOW/PASSIVE SOLAR PROGRAM FINAL REPORT

    E-Print Network [OSTI]

    Viswanathan, R.

    2011-01-01T23:59:59.000Z

    TI Reflective Solar Control Film on Windows Gains AcceptancelReflective Solar Control Film on Windows Gains Acceptance",optical window shutter, the cholesteric liquid crystal film

  14. Performance Criteria for Residential Zero Energy Windows

    SciTech Connect (OSTI)

    Arasteh, Dariush; Goudey, Howdy; Huang, Joe; Kohler, Christian; Mitchell, Robin

    2006-10-09T23:59:59.000Z

    This paper shows that the energy requirements for today's typical efficient window products (i.e. ENERGY STAR{trademark} products) are significant when compared to the needs of Zero Energy Homes (ZEHs). Through the use of whole house energy modeling, typical efficient products are evaluated in five US climates and compared against the requirements for ZEHs. Products which meet these needs are defined as a function of climate. In heating dominated climates, windows with U-factors of 0.10 Btu/hr-ft{sup 2}-F (0.57 W/m{sup 2}-K) will become energy neutral. In mixed heating/cooling climates a low U-factor is not as significant as the ability to modulate from high SHGCs (heating season) to low SHGCs (cooling season).

  15. End User Impacts of Automated Electrochromic Windows in a Pilot

    E-Print Network [OSTI]

    LBNL-6027E End User Impacts of Automated Electrochromic Windows in a Pilot Retrofit Application E Electrochromic Windows in a Pilot Retrofit Application Eleanor S. Lee1 Abstract , Erin S. Claybaugh Building Independence Avenue, S.W., Washington, DC 20585 USA Automated electrochromic (EC) windows, advanced thermally

  16. DWPF GLASS BEADS AND GLASS FRIT TRANSPORT DEMONSTRATION

    SciTech Connect (OSTI)

    Adamson, D; Bradley Pickenheim, B

    2008-11-24T23:59:59.000Z

    DWPF is considering replacing irregularly shaped glass frit with spherical glass beads in the Slurry Mix Evaporator (SME) process to decrease the yield stress of the melter feed (a non-Newtonian Bingham Plastic). Pilot-scale testing was conducted on spherical glass beads and glass frit to determine how well the glass beads would transfer when compared to the glass frit. Process Engineering Development designed and constructed the test apparatus to aid in the understanding and impacts that spherical glass beads may have on the existing DWPF Frit Transfer System. Testing was conducted to determine if the lines would plug with the glass beads and the glass frit slurry and what is required to unplug the lines. The flow loop consisted of vertical and horizontal runs of clear PVC piping, similar in geometry to the existing system. Two different batches of glass slurry were tested: a batch of 50 wt% spherical glass beads and a batch of 50 wt% glass frit in process water. No chemicals such as formic acid was used in slurry, only water and glass formers. The glass beads used for this testing were commercially available borosilicate glass of mesh size -100+200. The glass frit was Frit 418 obtained from DWPF and is nominally -45+200 mesh. The spherical glass beads did not have a negative impact on the frit transfer system. The transferring of the spherical glass beads was much easier than the glass frit. It was difficult to create a plug with glass bead slurry in the pilot transfer system. When a small plug occurred from setting overnight with the spherical glass beads, the plug was easy to displace using only the pump. In the case of creating a man made plug in a vertical line, by filling the line with spherical glass beads and allowing the slurry to settle for days, the plug was easy to remove by using flush water. The glass frit proved to be much more difficult to transfer when compared to the spherical glass beads. The glass frit impacted the transfer system to the point that the test apparatus had to be disassembled to dislodge the plugs created in the system.

  17. Glass matrix armor

    DOE Patents [OSTI]

    Calkins, Noel C. (Los Alamos, NM)

    1991-01-01T23:59:59.000Z

    An armor system which utilizes glass. A plurality of constraint cells are mounted on a surface of a substrate, which is metal armor plate or a similar tough material, such that the cells almost completely cover the surface of the substrate. Each constraint cell has a projectile-receiving wall parallel to the substrate surface and has sides which are perpendicular to and surround the perimeter of the receiving wall. The cells are mounted such that, in one embodiment, the substrate surface serves as a sixth side or closure for each cell. Each cell has inside of it a plate, termed the front plate, which is parallel to and in contact with substantially all of the inside surface of the receiving wall. The balance of each cell is completely filled with a projectile-abrading material consisting of glass and a ceramic material and, in certain embodiments, a polymeric material. The glass may be in monolithic form or particles of ceramic may be dispersed in a glass matrix. The ceramic material may be in monolithic form or may be in the form of particles dispersed in glass or dispersed in said polymer.

  18. Energy Saving Glass Lamination via Selective Radio Frequency Heating

    SciTech Connect (OSTI)

    Allan, Shawn M.

    2012-02-27T23:59:59.000Z

    This project focused on advancing radio-frequency (RF) lamination technology closer to commercial implementation, in order to reduce the energy intensity of glass lamination by up to 90%. Lamination comprises a wide range of products including autoglass, architectural safety and innovative design glass, transparent armor (e.g. bullet proof glass), smart glass, mirrors, and encapsulation of photovoltaics. Lamination is also the fastest growing segment of glass manufacturing, with photovoltaics, architectural needs, and an anticipated transition to laminated side windows in vehicles. The state-of-the-art for glass lamination is to use autoclaves, which apply heat and uniform gas pressure to bond the laminates over the course of 1 to 18 hours. Laminates consist of layers of glass or other materials bonded with vinyl or urethane interlayers. In autoclaving, significant heat energy is lost heating the chamber, pressurized air, glass racks, and the glass. In RF lamination, the heat is generated directly in the vinyl interlayer, causing it to heat and melt quickly, in just 1 to 10 minutes, without significantly heating the glass or the equipment. The main purpose of this project was to provide evidence that low energy, rapid RF lamination quality met the same standards as conventionally autoclaved windows. The development of concepts for laminating curved glass with RF lamination was a major goal. Other primary goals included developing a stronger understanding of the lamination product markets described above, and to refine the potential benefits of commercial implementation. The scope of the project was to complete implementation concept studies in preparation for continuation into advanced development, pilot studies, and commercial implementation. The project consisted of 6 main tasks. The first dealt with lamination with poly-vinyl butyral (PVB) interlayers, which prior work had shown difficulties in achieving good quality laminates, working with Pilkington North America. The second task dealt with a study of current lamination processes in the various laminate industries, and development of concepts for integrating RF lamination into new or existing processes. The third task explored the use of a non-destructive technique for analyzing laminate adhesion with the University of Illinois at Urbana-Champaign. The fourth task focused on developing concepts for curved glass lamination using RF lamination. The fifth and sixth tasks together comprised an analysis of laminate product markets, ranking for applicability and commercialization potential, and the development of commercialization strategies for those products. In addition, throughout the project as new experimental data and conventional process data were obtained, the benefits analysis of RF lamination was refined. The goals of the project described above were achieved, positioning RF lamination for the next stage growth envisioned in the original Industrial Grand Challenge proposal. Working with Pilkington North America, lamination of flat autoglass with PVB was achieved, meeting all 16 stringent industry tests. In particular, PVB laminates made with RF lamination passed environmental tests including the high temperature, 120 C bake test, without significant formation of bubbles (defects). The adhesion of PVB to glass was measured using the pummel method. Adhesion values ranging from 1 to 7 out of 10 were obtained. The significant process parameters affecting the environmental and adhesion performance were identified through a designed experiment. Pre-lamination process variables including PVB storage humidity and the de-airing process (vacuum or nip rolling) were significant, as well as the level of pressure applied to the laminate during the RF process. Analysis of manufacturing with RF lamination equipment, based on the processes developed indicated that 3 RF presses could replace a typical auto-industry autoclave to achieve equal or greater throughput with possibly less capital cost and smaller footprint. Concepts for curved lamination identifying castable molds for

  19. Energy Saving Glass Lamination via Selective Radio Frequency Heating

    SciTech Connect (OSTI)

    Allan, Shawn M.; Baranova, Inessa; Poley, Joseph; Reis, Henrique

    2012-02-27T23:59:59.000Z

    This project focused on advancing radio-frequency (RF) lamination technology closer to commercial implementation, in order to reduce the energy intensity of glass lamination by up to 90%. Lamination comprises a wide range of products including autoglass, architectural safety and innovative design glass, transparent armor (e.g. bullet proof glass), smart glass, mirrors, and encapsulation of photovoltaics. Lamination is also the fastest growing segment of glass manufacturing, with photovoltaics, architectural needs, and an anticipated transition to laminated side windows in vehicles. The state-of-the-art for glass lamination is to use autoclaves, which apply heat and uniform gas pressure to bond the laminates over the course of 1 to 18 hours. Laminates consist of layers of glass or other materials bonded with vinyl or urethane interlayers. In autoclaving, significant heat energy is lost heating the chamber, pressurized air, glass racks, and the glass. In RF lamination, the heat is generated directly in the vinyl interlayer, causing it to heat and melt quickly, in just 1 to 10 minutes, without significantly heating the glass or the equipment. The main purpose of this project was to provide evidence that low energy, rapid RF lamination quality met the same standards as conventionally autoclaved windows. The development of concepts for laminating curved glass with RF lamination was a major goal. Other primary goals included developing a stronger understanding of the lamination product markets described above, and to refine the potential benefits of commercial implementation. The scope of the project was to complete implementation concept studies in preparation for continuation into advanced development, pilot studies, and commercial implementation. The project consisted of 6 main tasks. The first dealt with lamination with poly-vinyl butyral (PVB) interlayers, which prior work had shown difficulties in achieving good quality laminates, working with Pilkington North America. The second task dealt with a study of current lamination processes in the various laminate industries, and development of concepts for integrating RF lamination into new or existing processes. The third task explored the use of a non-destructive technique for analyzing laminate adhesion with the University of Illinois at Urbana-Champaign. The fourth task focused on developing concepts for curved glass lamination using RF lamination. The fifth and sixth tasks together comprised an analysis of laminate product markets, ranking for applicability and commercialization potential, and the development of commercialization strategies for those products. In addition, throughout the project as new experimental data and conventional process data were obtained, the benefits analysis of RF lamination was refined. The goals of the project described above were achieved, positioning RF lamination for the next stage growth envisioned in the original Industrial Grand Challenge proposal. Working with Pilkington North America, lamination of flat autoglass with PVB was achieved, meeting all 16 stringent industry tests. In particular, PVB laminates made with RF lamination passed environmental tests including the high temperature, 120 ���°C bake test, without significant formation of bubbles (defects). The adhesion of PVB to glass was measured using the pummel method. Adhesion values ranging from 1 to 7 out of 10 were obtained. The significant process parameters affecting the environmental and adhesion performance were identified through a designed experiment. Pre-lamination process variables including PVB storage humidity and the de-airing process (vacuum or nip rolling) were significant, as well as the level of pressure applied to the laminate during the RF process. Analysis of manufacturing with RF lamination equipment, based on the processes developed indicated that 3 RF presses could replace a typical auto-industry autoclave to achieve equal or greater throughput with possibly less capital cost and smaller footprint. Concepts for curved lamination id

  20. Energy Efficiency and Conservation Block Grant Program

    Broader source: Energy.gov (indexed) [DOE]

    Description Energy efficiency retrofits: 1) replacement of chillers and upgrade of HVAC ducts at the Law Enforcement Center; 2) window tinting and insulation at the Planning...

  1. Monitored Energy Performance of Electrochromic Windows Controlled for Daylight and Visual Comfort

    E-Print Network [OSTI]

    Lee, Eleanor S.; DiBartolomeo, Dennis L.; Klems, Joseph; Yazdanian, Mehry; Selkowitz, Stephen E.

    2005-01-01T23:59:59.000Z

    absorptive electrochromic (EC) windows tested were market-electrochromic windows that were deemed sufficiently mature for market

  2. Monitored Energy Performance of Electrochromic Windows Controlled for Daylight and Visual Comfort

    E-Print Network [OSTI]

    Lee, Eleanor S.; DiBartolomeo, Dennis L.; Klems, Joseph; Yazdanian, Mehry; Selkowitz, Stephen E.

    2005-01-01T23:59:59.000Z

    Subject responses to electrochromic windows. Submitted toin a full-scale electrochromic window testbed. Technicaloptimization of electrochromic operations for occupant

  3. List of Windows Incentives | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision hasInformation Earth's Heat JumpInc Place:KeystoneSolarList ofPassiveMachine ControlsWindows

  4. Effect of furnace atmosphere on E-glass foaming

    SciTech Connect (OSTI)

    Kim, Dong-Sang; Dutton, Bryan C.; Hrma, Pavel R.; Pilon, Laurent

    2006-12-01T23:59:59.000Z

    The effect of furnace atmosphere on E-glass foaming generated in crucible has been studied with a specific goal to understand the impact of increased water content on foaming in oxy-fired furnaces. E-glass foams were generated in a fused-quartz crucible located in a quartz window furnace equipped with video recording. The present study showed that humidity in the furnace atmosphere destabilizes foam, while other gases have little effect on foam stability. This study suggests that the higher foaming in oxy-fired furnace compared to air-fired is caused by the effect of water on early sulfate decomposition, promoting more efficient refining gas generation from sulfate (known as “dilution effect”).

  5. Developing Low-Conductance Window Frames: Capabilities and Limitations of Current Window Heat Transfer Design Tools

    E-Print Network [OSTI]

    Transfer Design Tools Arild Gustavsen1,* , Dariush Arasteh2 , Bjørn Petter Jelle3,4 , Charlie Curcija5-conductance window frames requires accurate simulation tools for product research and development. Based and develop recommendation for inclusion into the design fenestration tools. 3. Assess existing correlations

  6. The Color Glass Condensate

    E-Print Network [OSTI]

    F. Gelis; E. Iancu; J. Jalilian-Marian; R. Venugopalan

    2010-02-01T23:59:59.000Z

    We provide a broad overview of the theoretical status and phenomenological applications of the Color Glass Condensate effective field theory describing universal properties of saturated gluons in hadron wavefunctions that are extracted from deeply inelastic scattering and hadron-hadron collision experiments at high energies.

  7. Measure Guideline: Energy-Efficient Window Performance and Selection

    SciTech Connect (OSTI)

    Carmody, J.; Haglund, K.

    2012-11-01T23:59:59.000Z

    This document provides guidelines for the selection of energy-efficient windows in new and existing residential construction in all US climate zones. It includes information on window products, their attributes and performance. It provides cost/benefit information on window energy savings as well as information on non-energy benefits such as thermal comfort and reduced HVAC demands. The document also provides information on energy impacts of design decisions such as window orientation, total glazing area and shading devices and conditions. Information on resources for proper window installation is included as well. This document is for builders, homeowners, designers and anyone making decisions about selecting energy efficient window. It is intended to complement other Building America information and efforts.

  8. Stand-alone photovoltaic (PV) powered electrochromic window

    DOE Patents [OSTI]

    Benson, David K. (Golden, CO); Crandall, Richard S. (Boulder, CO); Deb, Satyendra K. (Boulder, CO); Stone, Jack L. (Lakewood, CO)

    1995-01-01T23:59:59.000Z

    A variable transmittance double pane window includes an electrochromic material that has been deposited on one pane of the window in conjunction with an array of photovoltaic cells deposited along an edge of the pane to produce the required electric power necessary to vary the effective transmittance of the window. A battery is placed in a parallel fashion to the array of photovoltaic cells to allow the user the ability to manually override the system when a desired transmittance is desired.

  9. Stand-alone photovoltaic (PV) powered electrochromic window

    DOE Patents [OSTI]

    Benson, D.K.; Crandall, R.S.; Deb, S.K.; Stone, J.L.

    1995-01-24T23:59:59.000Z

    A variable transmittance double pane window includes an electrochromic material that has been deposited on one pane of the window in conjunction with an array of photovoltaic cells deposited along an edge of the pane to produce the required electric power necessary to vary the effective transmittance of the window. A battery is placed in a parallel fashion to the array of photovoltaic cells to allow the user the ability to manually override the system when a desired transmittance is desired. 11 figures.

  10. Production of glass or glass-ceramic to metal seals with the application of pressure

    DOE Patents [OSTI]

    Kelly, Michael D. (West Alexandria, OH); Kramer, Daniel P. (Dayton, OH)

    1987-11-10T23:59:59.000Z

    In a process for preparing a glass or glass-ceramic to metal seal comprising contacting the glass with the metal and heat-treating the glass and metal under conditions whereby the glass to metal seal is effected and, optionally, the glass is converted to a glass-ceramic, an improvement comprises carrying out the heat-treating step using hot isostatic pressing.

  11. Production of glass or glass-ceramic to metal seals with the application of pressure

    DOE Patents [OSTI]

    Kelly, M.D.; Kramer, D.P.

    1985-01-04T23:59:59.000Z

    In a process for preparing a glass or glass-ceramic to metal seal comprising contacting the glass with the metal and heat-treating the glass and metal under conditions whereby the glass to metal seal is effected and, optionally, the glass is converted to a glass-ceramic, an improvement comprises carrying out the heat-treating step using hot isostatic pressing.

  12. Highly Insulating Windows Volume Purchase Program Final Report

    SciTech Connect (OSTI)

    Parker, Graham B.; Mapes, Terry S.; Zalis, WJ

    2013-02-01T23:59:59.000Z

    This report summarizes the Highly Insulating Windows Volume Purchase Program, conduced by PNNL for DOE-BTP, including a summary of outcomes and lessons learned.

  13. A Design Guide for Early-Market Electrochromic Windows

    E-Print Network [OSTI]

    2006-01-01T23:59:59.000Z

    of a thin-film ceramic electrochromic window: Field studywindows in a bleached state (left) or colored state (right). Electrochromic coatings (EC) are switchable thin-film

  14. The robust vehicle routing problem with time windows

    E-Print Network [OSTI]

    Agostinho Agra

    2012-10-02T23:59:59.000Z

    Oct 2, 2012 ... Abstract: This paper addresses the robust vehicle routing problem with time windows. We are motivated by a problem that arises in maritime ...

  15. Robust Inventory Routing with Flexible Time Window Allocation

    E-Print Network [OSTI]

    Chengliang Zhang

    2015-01-15T23:59:59.000Z

    Jan 15, 2015 ... Abstract: This paper studies a robust maritime inventory routing problem with time windows and stochastic travel times. One of the novelties of ...

  16. Impacts of Operating Hardware on Window Thermal Performance

    E-Print Network [OSTI]

    Hart, Robert

    2014-01-01T23:59:59.000Z

    and Renewable Energy, Office of Building Technology,Building Technologies Program of the U.S. Department ofproject ”Improved Window Technologies for Energy Efficient

  17. Isocurvature forecast in the anthropic axion window

    E-Print Network [OSTI]

    J. Hamann; S. Hannestad; G. G. Raffelt; Y. Y. Y. Wong

    2009-06-16T23:59:59.000Z

    We explore the cosmological sensitivity to the amplitude of isocurvature fluctuations that would be caused by axions in the "anthropic window" where the axion decay constant f_a >> 10^12 GeV and the initial misalignment angle Theta_i << 1. In a minimal Lambda-CDM cosmology extended with subdominant scale-invariant isocurvature fluctuations, existing data constrain the isocurvature fraction to alpha < 0.09 at 95% C.L. If no signal shows up, Planck can improve this constraint to 0.042 while an ultimate CMB probe limited only by cosmic variance in both temperature and E-polarisation can reach 0.017, about a factor of five better than the current limit. In the parameter space of f_a and H_I (Hubble parameter during inflation) we identify a small region where axion detection remains within the reach of realistic cosmological probes.

  18. MAVIS III -- A Windows 95/NT Upgrade

    SciTech Connect (OSTI)

    Hardwick, M.F. [Sandia National Labs., Livermore, CA (United States). GTS Engineering Dept.

    1997-12-01T23:59:59.000Z

    MAVIS (Modeling and Analysis of Explosive Valve Interactions) is a computer program that simulates operation of explosively actuated valve. MAVIS was originally written in Fortran in the mid 1970`s and was primarily run on the Sandia Vax computers in use through the early 1990`s. During the mid to late 1980`s MAVIS was upgraded to include the effects of plastic deformation and it became MAVIS II. When the Vax computers were retired, the Gas Transfer System (GTS) Development Department ported the code to the Macintosh and PC platforms, where it ran as a simple console application. All graphical output was lost during these ports. GTS code developers recently completed an upgrade that provides a Windows 95/NT MAVIS application and restores all of the original graphical output. This upgrade is called MAVIS III version 1.0. This report serves both as a user`s manual for MAVIS III v 1.0 and as a general software development reference.

  19. Managing coherence via put/get windows

    DOE Patents [OSTI]

    Blumrich, Matthias A. (Ridgefield, CT); Chen, Dong (Croton on Hudson, NY); Coteus, Paul W. (Yorktown Heights, NY); Gara, Alan G. (Mount Kisco, NY); Giampapa, Mark E. (Irvington, NY); Heidelberger, Philip (Cortlandt Manor, NY); Hoenicke, Dirk (Ossining, NY); Ohmacht, Martin (Yorktown Heights, NY)

    2011-01-11T23:59:59.000Z

    A method and apparatus for managing coherence between two processors of a two processor node of a multi-processor computer system. Generally the present invention relates to a software algorithm that simplifies and significantly speeds the management of cache coherence in a message passing parallel computer, and to hardware apparatus that assists this cache coherence algorithm. The software algorithm uses the opening and closing of put/get windows to coordinate the activated required to achieve cache coherence. The hardware apparatus may be an extension to the hardware address decode, that creates, in the physical memory address space of the node, an area of virtual memory that (a) does not actually exist, and (b) is therefore able to respond instantly to read and write requests from the processing elements.

  20. Simulating Complex Window Systems using BSDF Data

    SciTech Connect (OSTI)

    Konstantoglou, Maria; Jonsson, Jacob; Lee, Eleanor

    2009-06-22T23:59:59.000Z

    Nowadays, virtual models are commonly used to evaluate the performance of conventional window systems. Complex fenestration systems can be difficult to simulate accurately not only because of their geometry but also because of their optical properties that scatter light in an unpredictable manner. Bi-directional Scattering Distribution Functions (BSDF) have recently been developed based on a mixture of measurements and modelling to characterize the optics of such systems. This paper describes the workflow needed to create then use these BSDF datasets in the Radiance lighting simulation software. Limited comparisons are made between visualizations produced using the standard ray-tracing method, the BSDF method, and that taken in a full-scale outdoor mockup.

  1. Porting salinas to the windows platform.

    SciTech Connect (OSTI)

    Reese, Garth M.; Wilson, Christopher Riley

    2006-06-01T23:59:59.000Z

    The ASC program has enabled significant development of high end engineering applications on massively parallel machines. There is a great benefit in providing these applications on the desktop of the analysts and designers, at least insofar as the small models may be run on these platforms, thus providing a tool set that spans the application needs. This effort documents the work of porting Salinas to the WINDOWS{trademark} platform. Selection of the tools required to compile, link, test and run Salinas in this environment is discussed. Significant problems encountered along the way are listed along with an estimation of the overall cost of the port. This report may serve as a baseline for streamlining further porting activities with other ASC codes.

  2. Managing coherence via put/get windows

    DOE Patents [OSTI]

    Blumrich, Matthias A. (Ridgefield, CT); Chen, Dong (Croton on Hudson, NY); Coteus, Paul W. (Yorktown Heights, NY); Gara, Alan G. (Mount Kisco, NY); Giampapa, Mark E. (Irvington, NY); Heidelberger, Philip (Cortlandt Manor, NY); Hoenicke, Dirk (Ossining, NY); Ohmacht, Martin (Yorktown Heights, NY)

    2012-02-21T23:59:59.000Z

    A method and apparatus for managing coherence between two processors of a two processor node of a multi-processor computer system. Generally the present invention relates to a software algorithm that simplifies and significantly speeds the management of cache coherence in a message passing parallel computer, and to hardware apparatus that assists this cache coherence algorithm. The software algorithm uses the opening and closing of put/get windows to coordinate the activated required to achieve cache coherence. The hardware apparatus may be an extension to the hardware address decode, that creates, in the physical memory address space of the node, an area of virtual memory that (a) does not actually exist, and (b) is therefore able to respond instantly to read and write requests from the processing elements.

  3. INTEGRATED ENERGY EFFICIENT WINDOW-WALL SYSTEMS

    SciTech Connect (OSTI)

    Michael Arney, Ph.D.

    2002-12-31T23:59:59.000Z

    The building industry faces the challenge of reducing energy use while simultaneously improving construction methods and marketability. This paper describes the first phase of a project to address these concerns by designing an Integrated Window Wall System (IWWS) that can be commercialized. This work builds on previous research conducted during the 1990's by Lawrence Berkeley national Laboratories (LBNL). During this phase, the objective was to identify appropriate technologies, problems and issues and develop a number of design concepts. Four design concepts were developed into prototypes and preliminary energy analyses were conducted Three of these concepts (the foam wall, steel wall, and stiffened plate designs) showed particular potential for meeting the project objectives and will be continued into a second phase where one or two of the systems will be brought closer to commercialization.

  4. Analytical Plan for Roman Glasses

    SciTech Connect (OSTI)

    Strachan, Denis M.; Buck, Edgar C.; Mueller, Karl T.; Schwantes, Jon M.; Olszta, Matthew J.; Thevuthasan, Suntharampillai; Heeren, Ronald M.

    2011-01-01T23:59:59.000Z

    Roman glasses that have been in the sea or underground for about 1800 years can serve as the independent “experiment” that is needed for validation of codes and models that are used in performance assessment. Two sets of Roman-era glasses have been obtained for this purpose. One set comes from the sunken vessel the Iulia Felix; the second from recently excavated glasses from a Roman villa in Aquileia, Italy. The specimens contain glass artifacts and attached sediment or soil. In the case of the Iulia Felix glasses quite a lot of analytical work has been completed at the University of Padova, but from an archaeological perspective. The glasses from Aquileia have not been so carefully analyzed, but they are similar to other Roman glasses. Both glass and sediment or soil need to be analyzed and are the subject of this analytical plan. The glasses need to be analyzed with the goal of validating the model used to describe glass dissolution. The sediment and soil need to be analyzed to determine the profile of elements released from the glass. This latter need represents a significant analytical challenge because of the trace quantities that need to be analyzed. Both pieces of information will yield important information useful in the validation of the glass dissolution model and the chemical transport code(s) used to determine the migration of elements once released from the glass. In this plan, we outline the analytical techniques that should be useful in obtaining the needed information and suggest a useful starting point for this analytical effort.

  5. Radiation-transparent windows, method for imaging fluid transfers

    DOE Patents [OSTI]

    Shu, Deming (Darien, IL); Wang, Jin (Burr Ridge, IL)

    2011-07-26T23:59:59.000Z

    A thin, x-ray-transparent window system for environmental chambers involving pneumatic pressures above 40 bar is presented. The window allows for x-ray access to such phenomena as fuel sprays injected into a pressurized chamber that mimics realistic internal combustion engine cylinder operating conditions.

  6. Avalanches through windows: Multiscale visualization in magnetic thin films

    E-Print Network [OSTI]

    Sethna, James P.

    Avalanches through windows: Multiscale visualization in magnetic thin films Alessandro Magni, Cornell University, Ithaca, NY 14853-2501 Abstract--The dynamics of domain walls motion in thin films dynamics, but are strongly dependent on the size of the windows chosen. Here we investigate how to properly

  7. Benefits of Windows Small Business Server Code Name "Aurora"

    E-Print Network [OSTI]

    Hunt, Galen

    Benefits of Windows Small Business Server Code Name "Aurora" includes: Daily automatic backups Business Server Code Name "Aurora" provides an easy-to-use solution ideal for first server small businesses with up to 25 users, Windows Small Business Server Code Name "Aurora" provides a cost-effective and easy

  8. Validation of the Window Model of the Modelica Buildings Library

    E-Print Network [OSTI]

    LBNL-5735E Validation of the Window Model of the Modelica Buildings Library Thierry Stephane MODEL OF THE MODELICA BUILDINGS LIBRARY Thierry Stephane Nouidui, Michael Wetter, and Wangda Zuo the validation of the window model of the free open-source Modelica Buildings library. This paper starts

  9. Budget Windows, Sunsets and Fiscal Control Alan J. Auerbach

    E-Print Network [OSTI]

    Sadoulet, Elisabeth

    Budget Windows, Sunsets and Fiscal Control Alan J. Auerbach University of California, Berkeley have struggled to find the right method of controlling public spending and budget deficits. In recent years, the United States has evaluated policy changes using a ten-year budget window. The use of a multi

  10. Boron nitride protective coating of beryllium window surfaces

    SciTech Connect (OSTI)

    Gmuer, N.F.

    1991-12-01T23:59:59.000Z

    The use of beryllium windows on white synchrotron radiation beamlines is constrained by the fact that the downstream surfaces of these windows should not be exposed to ambient atmosphere. They should, rather, be protected by a tail-piece under vacuum or containing helium atmosphere. This tailpiece is typically capped by Kapton (3M Corporation, St. Paul, MN) or aluminum foil. The reason for such an arrangement is due to the health risk associated with contaminants (BeO) which from on the exposed beryllium window surfaces and due to possible loss of integrity of the windows. Such a tail-piece may, however, add unwanted complications to the beamline in the form of vacuum pumps or helium supplies and their related monitoring systems. The Kapton windows may burn through in the case of high intensity beams and lower energy radiation may be absorbed in the case of aluminum foil windows. A more ideal situation would be to provide a coating for the exposed beryllium window surface, sealing it off from the atmosphere, thus preventing contamination and/or degradation of the window, and eliminating the need for helium or vacuum equipment.

  11. Lighting energy savings potential of split-pane electrochromic windows controlled for daylighting with visual comfort

    SciTech Connect (OSTI)

    Software, Anyhere; Fernandes, Luis; Lee, Eleanor; Ward, Greg

    2013-03-15T23:59:59.000Z

    A simulation study was conducted to evaluate lighting energy savings of split-pane electrochromic (EC) windows controlled to satisfy key visual comfort parameters. Using the Radiance lighting simulation software, interior illuminance and luminance levels were computed for a south-facing private office illuminated by a window split into two independently-controlled EC panes. The transmittance of these was optimized hourly for a workplane illuminance target while meeting visual comfort constraints, using a least-squares algorithm with linear inequality constraints. Blinds were successively deployed until visual comfort criteria were satisfied. The energy performance of electrochromics proved to be highly dependent on how blinds were controlled. With hourly blind position adjustments, electrochromics showed significantly higher (62percent and 53percent, respectively without and with overhang) lighting energy consumption than clear glass. With a control algorithm designed to better approximate realistic manual control by an occupant, electrochromics achieved significant savings (48percent and 37percent, respectively without and with overhang). In all cases, energy consumption decreased when the workplace illuminance target was increased. In addition, the fraction of time during which the occupant had an unobstructed view of the outside was significantly greater with electrochromics: 10 months out of the year versus a handful of days for the reference case.

  12. Mixed polyanion glass cathodes: Iron phosphate vanadate glasses

    SciTech Connect (OSTI)

    Kercher, Andrew K [ORNL; Ramey, Joanne Oxendine [ORNL; Carroll, Kyler J [Massachusetts Institute of Technology (MIT); Kiggans Jr, James O [ORNL; Veith, Gabriel M [ORNL; Meisner, Roberta [Oak Ridge National Laboratory (ORNL); Boatner, Lynn A [ORNL; Dudney, Nancy J [ORNL

    2014-01-01T23:59:59.000Z

    Mixed polyanion (MP) glasses have been investigated for use as cathodes in lithium ion batteries. MP glass cathodes are similar in composition to theoretically promising crystalline polyanionic (CP) cathodes (e.g., lithium cobalt phosphate, lithium manganese silicate), but with proper polyanion substitution, they can be designed to overcome the key shortcomings of CP cathodes, such as poor electrical conductivity and irreversible phase changes. Iron phosphate/vanadate glasses were chosen as a first demonstration of the MP glass concept. Polyanion substitution with vanadate was shown to improve the intercalation capacity of an iron phosphate glass from almost zero to full theoretical capacity. In addition, the MP glass cathodes also exhibited an unexpected second high-capacity electrochemical reaction. X-ray absorption near-edge structure (XANES) and x-ray diffraction (XRD) of cathodes from cells having different states of charge suggested that this second electrochemical reaction is a glass-state conversion reaction. With a first demonstration established, MP glass materials utilizing an intercalation and/or glass-state conversion reaction are promising candidates for future high-energy cathode research.

  13. Demographic Window, H. G. Muller et al. 1 Demographic Window to Aging in the Wild: Constructing Life

    E-Print Network [OSTI]

    MĂĽller, Hans-Georg

    Demographic Window, H. G. M¨uller et al. 1 Demographic Window to Aging in the Wild: Constructing for wild populations. A demographic key identity is established that leads to a method whereby age identity is established for the continuous case where the survival schedule of the wild population

  14. Compositional threshold for Nuclear Waste Glass Durability

    SciTech Connect (OSTI)

    Kruger, Albert A. [Pacific Northwest National Lab., Richland, WA (United States); Farooqi, Rahmatullah [Pohang Univ. of Science and Technology, (Korea, Republic of); Hrma, Pavel R. [Pacific Northwest National Lab., Richland, WA (United States), Pohang Univ. of Science and Technology, (Korea, Republic of)

    2013-04-24T23:59:59.000Z

    Within the composition space of glasses, a distinct threshold appears to exist that separates "good" glasses, i.e., those which are sufficiently durable, from "bad" glasses of a low durability. The objective of our research is to clarify the origin of this threshold by exploring the relationship between glass composition, glass structure and chemical durability around the threshold region.

  15. Glass rupture disk

    DOE Patents [OSTI]

    Glass, S. Jill (Albuquerque, NM); Nicolaysen, Scott D. (Albuquerque, NM); Beauchamp, Edwin K. (Albuquerque, NM)

    2002-01-01T23:59:59.000Z

    A frangible rupture disk and mounting apparatus for use in blocking fluid flow, generally in a fluid conducting conduit such as a well casing, a well tubing string or other conduits within subterranean boreholes. The disk can also be utilized in above-surface pipes or tanks where temporary and controllable fluid blockage is required. The frangible rupture disk is made from a pre-stressed glass with controllable rupture properties wherein the strength distribution has a standard deviation less than approximately 5% from the mean strength. The frangible rupture disk has controllable operating pressures and rupture pressures.

  16. Glass | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in3.pdf Flash2006-53.pdf0.pdfCostAnalysis GeothermalEnergy GeothermalGetGlass and

  17. POROUS WALL, HOLLOW GLASS MICROSPHERES

    SciTech Connect (OSTI)

    Sexton, W.

    2012-06-30T23:59:59.000Z

    Hollow Glass Microspheres (HGM) is not a new technology. All one has to do is go to the internet and Google{trademark} HGM. Anyone can buy HGM and they have a wide variety of uses. HGM are usually between 1 to 100 microns in diameter, although their size can range from 100 nanometers to 5 millimeters in diameter. HGM are used as lightweight filler in composite materials such as syntactic foam and lightweight concrete. In 1968 a patent was issued to W. Beck of the 3M{trademark} Company for 'Glass Bubbles Prepared by Reheating Solid Glass Particles'. In 1983 P. Howell was issued a patent for 'Glass Bubbles of Increased Collapse Strength' and in 1988 H. Marshall was issued a patent for 'Glass Microbubbles'. Now Google{trademark}, Porous Wall, Hollow Glass Microspheres (PW-HGMs), the key words here are Porous Wall. Almost every article has its beginning with the research done at the Savannah River National Laboratory (SRNL). The Savannah River Site (SRS) where SRNL is located has a long and successful history of working with hydrogen and its isotopes for national security, energy, waste management and environmental remediation applications. This includes more than 30 years of experience developing, processing, and implementing special ceramics, including glasses for a variety of Department of Energy (DOE) missions. In the case of glasses, SRS and SRNL have been involved in both the science and engineering of vitreous or glass based systems. As a part of this glass experience and expertise, SRNL has developed a number of niches in the glass arena, one of which is the development of porous glass systems for a variety of applications. These porous glass systems include sol gel glasses, which include both xerogels and aerogels, as well as phase separated glass compositions, that can be subsequently treated to produce another unique type of porosity within the glass forms. The porous glasses can increase the surface area compared to 'normal glasses of a 1 to 2 order of magnitude, which can result in unique properties in areas such as hydrogen storage, gas transport, gas separations and purifications, sensors, global warming applications, new drug delivery systems and so on. One of the most interesting porous glass products that SRNL has developed and patented is Porous Wall, Hollow Glass Microspheres (PW-HGMs) that are being studied for many different applications. The European Patent Office (EPO) just recently notified SRS that the continuation-in-part patent application for the PW-HGMs has been accepted. The original patent, which was granted by the EPO on June 2, 2010, was validated in France, Germany and the United Kingdom. The microspheres produced are generally in the range of 2 to 100 microns, with a 1 to 2 micron wall. What makes the SRNL microspheres unique from all others is that the team in Figure 1 has found a way to induce and control porosity through the thin walls on a scale of 100 to 3000 {angstrom}. This is what makes the SRNL HW-HGMs one-of-a-kind, and is responsible for many of their unique properties and potential for various applications, including those in tritium storage, gas separations, H-storage for vehicles, and even a variety of new medical applications in the areas of drug delivery and MRI contrast agents. SRNL Hollow Glass Microspheres, and subsequent, Porous Wall, Hollow Glass Microspheres are fabricated using a flame former apparatus. Figure 2 is a schematic of the apparatus.

  18. Empirical assessment of a prismatic daylight-redirecting window film in a full-scale office testbed

    E-Print Network [OSTI]

    Thanachareonkit, Anothai

    2014-01-01T23:59:59.000Z

    of a microstructured prismatic window film in deep open plandaylight- redirecting window film in a full-scale officedaylight- redirecting window film in a full-scale office

  19. Experimental evaluation of the in-plane seismic behavior of store-front window systems

    E-Print Network [OSTI]

    Eva, Charles Almond

    2009-01-01T23:59:59.000Z

    was conducted. The window film (WF) series included 5’x5’damage states. When the window film is attached using theThe safety aspects of window film were very evident during

  20. U-032: Microsoft Security Bulletin Windows TCP/IP MS11-083 -...

    Broader source: Energy.gov (indexed) [DOE]

    Server 2003 Service Pack 2 Windows Server 2003 x64 Edition Service Pack 2 Active Directory Windows Server 2003 with SP2 for Itanium-based Systems Windows Vista Service Pack 2...

  1. Experimental and Numerical Examination of the Thermal Transmittance of High Performance Window Frames

    E-Print Network [OSTI]

    Gustavsen Ph.D., Arild

    2010-01-01T23:59:59.000Z

    windows are often called passive -house wind ows, as windowse window frames, like passive-house windows. In this p aperare supposed to satisfy the Passive house requirements of

  2. Aspects of the mechanics of metallic glasses

    E-Print Network [OSTI]

    Henann, David Lee

    2011-01-01T23:59:59.000Z

    Metallic glasses are amorphous materials that possess unique mechanical properties, such as high tensile strengths and good fracture toughnesses. Also, since they are amorphous, metallic glasses exhibit a glass transition, ...

  3. Ultra high vacuum broad band high power microwave window

    DOE Patents [OSTI]

    Nguyen-Tuong, Viet (Seaford, VA); Dylla, III, Henry Frederick (Yorktown, VA)

    1997-01-01T23:59:59.000Z

    An improved high vacuum microwave window has been developed that utilizes high density polyethylene coated on two sides with SiOx, SiNx, or a combination of the two. The resultant low dielectric and low loss tangent window creates a low outgassing, low permeation seal through which broad band, high power microwave energy may be passed. No matching device is necessary and the sealing technique is simple. The features of the window are broad band transmission, ultra-high vacuum compatibility with a simple sealing technique, low voltage standing wave ratio, high power transmission and low cost.

  4. Ultra high vacuum broad band high power microwave window

    DOE Patents [OSTI]

    Nguyen-Tuong, V.; Dylla, H.F. III

    1997-11-04T23:59:59.000Z

    An improved high vacuum microwave window has been developed that utilizes high density polyethylene coated on two sides with SiOx, SiNx, or a combination of the two. The resultant low dielectric and low loss tangent window creates a low outgassing, low permeation seal through which broad band, high power microwave energy may be passed. No matching device is necessary and the sealing technique is simple. The features of the window are broad band transmission, ultra-high vacuum compatibility with a simple sealing technique, low voltage standing wave ratio, high power transmission and low cost. 5 figs.

  5. Method of determining glass durability

    DOE Patents [OSTI]

    Jantzen, Carol Maryanne (Aiken, SC); Pickett, John Butler (Aiken, SC); Brown, Kevin George (Augusta, GA); Edwards, Thomas Barry (Aiken, SC)

    1998-01-01T23:59:59.000Z

    A process for determining one or more leachate concentrations of one or more components of a glass composition in an aqueous solution of the glass composition by identifying the components of the glass composition, including associated oxides, determining a preliminary glass dissolution estimator, .DELTA.G.sub.p, based upon the free energies of hydration for the component reactant species, determining an accelerated glass dissolution function, .DELTA.G.sub.a, based upon the free energy associated with weak acid dissociation, .DELTA.G.sub.a.sup.WA, and accelerated matrix dissolution at high pH, .DELTA.G.sub.a.sup.SB associated with solution strong base formation, and determining a final hydration free energy, .DELTA.G.sub.f. This final hydration free energy is then used to determine leachate concentrations for elements of interest using a regression analysis and the formula log.sub.10 (N C.sub.i (g/L))=a.sub.i +b.sub.i .DELTA.G.sub.f. The present invention also includes a method to determine whether a particular glass to be produced will be homogeneous or phase separated. The present invention is also directed to methods of monitoring and controlling processes for making glass using these determinations to modify the feedstock materials until a desired glass durability and homogeneity is obtained.

  6. Method of determining glass durability

    DOE Patents [OSTI]

    Jantzen, C.M.; Pickett, J.B.; Brown, K.G.; Edwards, T.B.

    1998-12-08T23:59:59.000Z

    A process is described for determining one or more leachate concentrations of one or more components of a glass composition in an aqueous solution of the glass composition by identifying the components of the glass composition, including associated oxides, determining a preliminary glass dissolution estimator, {Delta}G{sub p}, based upon the free energies of hydration for the component reactant species, determining an accelerated glass dissolution function, {Delta}G{sub a}, based upon the free energy associated with weak acid dissociation, {Delta}G{sub a}{sup WA}, and accelerated matrix dissolution at high pH, {Delta}G{sub a}{sup SB} associated with solution strong base formation, and determining a final hydration free energy, {Delta}G{sub f}. This final hydration free energy is then used to determine leachate concentrations for elements of interest using a regression analysis and the formula log{sub 10}(N C{sub i}(g/L))=a{sub i} + b{sub i}{Delta}G{sub f}. The present invention also includes a method to determine whether a particular glass to be produced will be homogeneous or phase separated. The present invention is also directed to methods of monitoring and controlling processes for making glass using these determinations to modify the feedstock materials until a desired glass durability and homogeneity is obtained. 4 figs.

  7. Laboratory Waste Disposal HAZARDOUS GLASS

    E-Print Network [OSTI]

    Sheridan, Jennifer

    of in normal trash containers. Pasteur pipettes Other pipettes and tips (glass or plastic) Slides and cover bodies (without needles) Container: Sturdy and leakproof with Hazardous Glass label. Either: Plastic resistant, leakproof plastic carboy with green sharps label. Do not fill these containers completely. Leave

  8. Refractory Glass Seals for SOFC

    SciTech Connect (OSTI)

    Chou, Y. S.; Stevenson, Jeffry W.

    2011-07-01T23:59:59.000Z

    One of the critical challenges facing planar solid oxide fuel cell (SOFC) technology is the need for reliable sealing technology. Seals must exhibit long-term stability and mechanical integrity in the high temperature SOFC environment during normal and transient operation. Several different approaches for sealing SOFC stacks are under development, including glass or glass-ceramic seals, metallic brazes, and compressive seals. Among glass seals, rigid glass-ceramics, self-healing glass, and composite glass approaches have been investigated under the SECA Core Technology Program. The U.S. Department of Energy's Pacific Northwest National Laboratory (PNNL) has developed the refractory glass approach in light of the fact that higher sealing temperatures (e.g., 930-1000 degrees C) may enhance the ultimate in-service bulk strength and electrical conductivity of contact materials, as well as the bonding strength between contact materials and adjacent SOFC components, such as interconnect coatings and electrodes. This report summarizes the thermal, chemical, mechanical, and electrical properties of the refractory sealing glass.

  9. Photo of the Week: The First Energy-Efficient Dual-Paned Windows...

    Broader source: Energy.gov (indexed) [DOE]

    Lab helped develop the first energy-efficient dual-paned windows, now used in buildings and homes worldwide for billions of dollars in energy savings. Current windows...

  10. State-of-the-Art Highly Insulating Window Frames - Research and Market Review

    E-Print Network [OSTI]

    Gustavsen, Arild

    2008-01-01T23:59:59.000Z

    through vacuum and electrochromic vacuum glazed windows,technologies, such as an electrochromic vacuum glazedof rebate depth on an electrochromic vacuum glazed window.

  11. Monitored Energy Performance of Electrochromic Windows Controlled for Daylight and Visual Comfort

    E-Print Network [OSTI]

    Lee, Eleanor S.; DiBartolomeo, Dennis L.; Klems, Joseph; Yazdanian, Mehry; Selkowitz, Stephen E.

    2005-01-01T23:59:59.000Z

    Windows Controlled for Daylight and Visual Comfort Eleanorof means to bring in daylight while minimizing window glare.was controlled to admit daylight while the lower zone was

  12. Glass science tutorial: Lecture No. 7, Waste glass technology for Hanford

    SciTech Connect (OSTI)

    Kruger, A.A.

    1995-07-01T23:59:59.000Z

    This paper presents the details of the waste glass tutorial session that was held to promote knowledge of waste glass technology and how this can be used at the Hanford Reservation. Topics discussed include: glass properties; statistical approach to glass development; processing properties of nuclear waste glass; glass composition and the effects of composition on durability; model comparisons of free energy of hydration; LLW glass structure; glass crystallization; amorphous phase separation; corrosion of refractories and electrodes in waste glass melters; and glass formulation for maximum waste loading.

  13. Bioactive Glass Scaffolds for Bone Regeneration

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    glass, adding ions to impart specific properties, enables them to manage the degradation rate of the glass, creating attractive and compliant scaffold materials. A variety...

  14. Switchable window based on electrochromic polymers Chunye Xu,a)

    E-Print Network [OSTI]

    Taya, Minoru

    Switchable window based on electrochromic polymers Chunye Xu,a) Lu Liu, Susan E. Legenski, Dai Ning March 2004) A large contrast ratio (> 60%) and rapid switching (0.3­1 s) electrochromic (EC) polymer

  15. Hydrogen Safety Project: Chemical analysis support task. Window ``E`` analyses

    SciTech Connect (OSTI)

    Jones, T.E.; Campbell, J.A.; Hoppe, E.W.; Greenwood, L.R.; Gillespie, B.M.

    1992-09-01T23:59:59.000Z

    Core samples taken from tank 101-SY at Hanford during ``window E`` were analyzed for organic and radiochemical constituents by staff of the Analytical Chemistry Laboratory at Pacific Northwest Laboratory. Westinghouse Hanford company submitted these samples to the laboratory.

  16. Building America Expert Meeting: Windows Options for New and...

    Broader source: Energy.gov (indexed) [DOE]

    The NorthernSTAR Building America Partnership held an Expert Meeting on Windows Options for New and Existing Homes on November 14, 2011 at the Nolte Building on the campus of the...

  17. Pennsylvania: New Series of Windows Has Potential to Save Energy...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    windows such as the OptiQ(tm) provide commercial building owners and operators with more energy efficient options to reduce heating and cooling expenses. The introduction of the...

  18. Performance Testing of Window Installation and Flashing Details

    E-Print Network [OSTI]

    Weston, T. A.; Herrin, J.

    2002-01-01T23:59:59.000Z

    and proposed installation practices incorporating new flashing materials. This paper focuses specifically on the installation practices relating to windows with mounting fins or flanges. REVIEW OF CURRENT PRACTICES AND ATTITUDES Interviews with builders... into two categories based on the how the flashing and the rough opening is treated. g167g32 2-Dimensional Methods: using flashing to extend protection around the perimeter of the window flanges on to the face of the sheathing, and g167g32 3...

  19. Improving the thermal performance of the US residential window stock

    SciTech Connect (OSTI)

    Brown, R.E.; Arasteh, D.K.; Eto, J.H.

    1992-05-01T23:59:59.000Z

    Windows have typically been the least efficient thermal component in the residential envelope, but technology advances over the past decade have helped to dramatically improve the energy efficiency of window products. While the thermal performance of these advanced technology windows can be easily characterized for a particular building application, few precise estimates exist of their aggregate impact on national or regional energy use. Policy-makers, utilities, researchers and the fenestration industry must better understand these products` ultimate conservation potential in order to determine the value of developing new products and initiating programs to accelerate their market acceptance. This paper presents a method to estimate the conservation potential of advanced window technologies, combining elements of two well-known modeling paradigms: supply curves of conserved energy and residential end-use forecasting. The unique features include: detailed descriptions of the housing stock by region and vintage, state-of-the-art thermal descriptions of window technologies, and incorporation of market effects to calculate achievable conservation potential and timing. We demonstrate the methodology by comparing, for all new houses built between 1990 and 2010, the conservation potential of very efficient, high R-value ``superwindows`` in the North Central federal region and spectrally-selective low-emissivity (moderate Revalue and solar transmittance) windows in California.

  20. Performance of a multifunctional PV/T hybrid solar window

    SciTech Connect (OSTI)

    Davidsson, Henrik; Perers, Bengt; Karlsson, Bjoern [Energy and Building Design, Lund University, P.O. Box 118, SE 221 00 Lund (Sweden)

    2010-03-15T23:59:59.000Z

    A building-integrated multifunctional PV/T solar window has been developed and evaluated. It is constructed of PV cells laminated on solar absorbers placed in a window behind the glazing. To reduce the cost of the solar electricity, tiltable reflectors have been introduced in the construction to focus radiation onto the solar cells. The reflectors render the possibility of controlling the amount of radiation transmitted into the building. The insulated reflectors also reduce the thermal losses through the window. A model for simulation of the electric and hot water production was developed. The model can perform yearly energy simulations where different features such as shading of the cells or effects of the glazing can be included or excluded. The simulation can be run with the reflectors in an active, up right, position or in a passive, horizontal, position. The simulation program was calibrated against measurements on a prototype solar window placed in Lund in the south of Sweden and against a solar window built into a single family house, Solgaarden, in Aelvkarleoe in the central part of Sweden. The results from the simulation shows that the solar window annually produces about 35% more electric energy per unit cell area compared to a vertical flat PV module. (author)

  1. Fracture mechanics of cellular glass

    SciTech Connect (OSTI)

    Zwissler, J.G.; Adams, M.A.

    1981-02-01T23:59:59.000Z

    Cellular glasses are prime candidate materials for the structural substrate of mirrored glass for solar concentrator reflecting panels. These materials are brittle, however, and susceptible to mechanical failure from slow crack growth caused by a stress corrosion mechanism. The results are detailed of one part of a program established to develop improved cellular glasses and to characterize the behavior of these and commercially available materials. Commercial and developmental cellular glasses were tested and analyzed using standard testing techniques and models developed from linear fracture mechanics. Two models describing the fracture behavior of these materials are developed. Slow crack growth behavior in cellular glass was found to be more complex than that encountered in dense glasses or ceramics. The crack velocity was found to be strongly dependent upon water vapor transport to the tip of the moving crack. The existence of a static fatigue limit was not conclusively established, however, it is speculated that slow crack growth behavior in Region I may be slower, by orders of magnitude, than that found in dense glasses.

  2. Highly Insulating Windows with a U-value less than 0.6 W/m2K

    SciTech Connect (OSTI)

    Wendell Rhine; Ying Tang; Wenting Dong; Roxana Trifu; Reduane Begag

    2008-11-30T23:59:59.000Z

    U.S. households rely primarily on three sources of energy: natural gas, electricity, and fuel oil. In the past several decades, electricity consumption by households has grown dramatically, and a significant portion of electricity used in homes is for lighting. Lighting includes both indoor and outdoor lighting and is found in virtually every household in the United States. In 2001, according to the US Energy Information Administration, lighting accounted for 101 billion kWh (8.8 percent) of U.S. household electricity use. Incandescent lamps, which are commonly found in households, are highly inefficient sources of light because about 90 percent of the energy used is lost as heat. For that reason, lighting has been one focus area to increase the efficiency of household electricity consumption. Windows have several functions, and one of the main functions is to provide a view to the outside. Daylighting is another one of windows main functions and determines the distribution of daylight to a space. Daylighting windows do not need to be transparent, and a translucent daylighting window is sufficient, and often desired, to diffuse the light and make the space more environmentally pleasing. In homes, skylights are one source of daylighting, but skylights are not very energy efficient and are inseparably linked to solar heat gain. In some climates, added solar heat gains from daylighting may be welcome; but in other climates, heat gain must be controlled. More energy efficient skylights and daylighting solutions, in general, are desired and can be designed by insulating them with aerogels. Aerogels are a highly insulating and transparent material in its pure form. The overall objective for this project was to prepare an economical, translucent, fiber-reinforced aerogel insulation material for daylighting applications that is durable for manufacturing purposes. This advanced insulation material will increase the thermal performance of daylighting windows, while satisfying constraints such as durability, cost, user acceptance, size limits, and environmental safety concerns. The energy efficient daylighting window will consist of a translucent and resilient aerogel panel sandwiched between glass panes in double glazed windows. Compared to the best windows available today, the double glazed translucent windows with 1/2-inch aerogel inserts will have a U-value of 1.2 W/m{sup 2} K (0.211 BTU/ft{sup 2} h F) without any coating or low conductivity fill gases. These windows will be more effective than the windows with an Energy Star rating of U-2 W/m{sup 2} K and could be made even more efficient by using low-e coated glass glazings and inert gas fills. This report summarizes the work accomplished on Cooperative Agreement DE-FC26-03NT41950. During this project, Aspen Aerogels made transparent and translucent aerogels from TMOS and TEOS. We characterized the transparency of the aerogels, reinforced the transparent aerogels with fibers and prepared large translucent aerogel panels and blankets. We also conducted an initial market study for energy efficient translucent windows. A lab-scale process was developed that could be scaled-up to manufacture blankets of these translucent aerogels. The large blankets prepared were used to fabricate prototype translucent windows and skylights. The primary goal of this project was to develop transparent, resilient, hydrophobic silica aerogels that have low thermal conductivities (R-10/inch) to be used to produce aerogel insulated double-glazing windows with a U value of 0.6 W/m{sup 2}K. To meet this objective we developed a process and equipment to produce blankets of translucent, hydrophobic aerogel. We focused on silica, organically-modified silica aerogels (Ormosils), and fiber reinforced silica aerogels due to the appreciable expertise in silica sol-gel processing available with the personnel at Aspen Aerogels, and also due to the quantity of knowledge available in the scientific literature. The project was conducted in three budget periods, herein called BP1, BP2 and BP3.

  3. Matlab for PhD students Basics 1 WS 2010/11 Matlab windows

    E-Print Network [OSTI]

    Kretzberg, Jutta

    Matlab for PhD students ­ Basics 1 ­ WS 2010/11 Matlab windows The matlab desktop can be edited and brought back with the "Desktop" menu, the windows can be docked and undocked from the main Matlab window -> Default · Command window o Issues commands to Matlab for processing o >> means that Matlab is ready

  4. Corrosion of Partially Crystallized Glasses

    SciTech Connect (OSTI)

    Hrma, Pavel R.; Riley, Brian J.; Vienna, John D.

    2002-05-21T23:59:59.000Z

    Using existing data on corrosion of partially crystallized, simulated, high-level waste glasses, coefficients were introduced to evaluate the cumulative influence of secondary effects, such as residual stresses or concentration gradients on product consistency test response. As compared to predictions based solely on residual glass composition effects, the results showed that cristobalite, eucryptite, and nepheline had a higher-than-predicted impact on glass corrosion, while the effects of baddeleyite, hematite, calcium-zirconium silicate, and zircon were close to those predicted. The effects of acmite and lithium silicate were opposite to those expected based on their compositions. The analysis revealed important limitations of the databases currently available. Better understanding of corrosion phenomena will require quantitative composition data, microscopic characterization of pristine and corroded surfaces, and long-term tests with glass coupons or monoliths.

  5. Glass Membrane For Controlled Diffusion Of Gases

    DOE Patents [OSTI]

    Shelby, James E. (Alfred Station, NY); Kenyon, Brian E. (Pittsburgh, PA)

    2001-05-15T23:59:59.000Z

    A glass structure for controlled permeability of gases includes a glass vessel. The glass vessel has walls and a hollow center for receiving a gas. The glass vessel contains a metal oxide dopant formed with at least one metal selected from the group consisting of transition metals and rare earth metals for controlling diffusion of the gas through the walls of the glass vessel. The vessel releases the gas through its walls upon exposure to a radiation source.

  6. BNFL Report Glass Formers Characterization

    SciTech Connect (OSTI)

    Schumacher, R.F.

    2000-07-27T23:59:59.000Z

    The objective of this task was to obtain powder property data on candidate glass former materials, sufficient to guide conceptual design and estimate the cost of glass former handling facilities as requested under Part B1 of BNFL Technical and Development Support. Twenty-nine glass forming materials were selected and obtained from vendors for the characterization of their physical properties, durability in caustic solution, and powder flow characteristics. A glass former was selected based on the characterization for each of the ten oxide classes required for Envelope A, B, and C mixtures. Three blends (A, B, and C) were prepared based on formulations provided by Vitreous State Laboratory and evaluated with the same methods employed for the glass formers. The properties obtained are presented in a series of attached Tables. It was determined that five of the ten glass formers, (kyanite, iron oxide, titania, zircon, and zinc oxide) have the potential to cause some level of solids f low problems. In addition, all of the blends may require consideration for their handling. A number of engineering considerations and recommendations were prepared based on the experimental findings, experience, and other process considerations. Recommendations for future testing are included. In conjunction with future work, it is recommended that a professional consultant be engaged to guide and assist with testing and design input.

  7. BNFL Report Glass Formers Characterization

    SciTech Connect (OSTI)

    Schumacher, R.F.

    2000-07-27T23:59:59.000Z

    The objective of this task was to obtain powder property data on candidate glass former materials, sufficient to guide conceptual design and estimate the cost of glass former handling facilities as requested under Part B1 of BNFL Technical and Development Support. Twenty-nine glass forming materials were selected and obtained from vendors for the characterization of their physical properties, durability in caustic solution, and powder flow characteristics. A glass former was selected based on the characterization for each of the ten oxide classes required for Envelope A, B, and C mixtures. Three blends (A, B, and C) were prepared based on formulations provided by Vitreous State Laboratory and evaluated with the same methods employed for the glass formers. The properties obtained are presented in a series of attached Tables. It was determined that five of the ten glass formers, (kyanite, iron oxide, titania, zircon, and zinc oxide) have the potential to cause some level of solids f low problems. The problems might include arching or ratholing in the silo/hopper. In addition, all of the blends may require consideration for their handling.

  8. Assessment of Environmentally Friendly Refrigerants for Window Air Conditioners

    SciTech Connect (OSTI)

    Bansal, Pradeep [ORNL] [ORNL; Shen, Bo [ORNL] [ORNL

    2014-01-01T23:59:59.000Z

    This paper presents technical assessment of environmentally friendly refrigerants for window air conditioners that currently use refrigerant R410A for residential and commercial applications. The alternative refrigerants that are studied for its replacement include R32, R600a, R290, R1234yf, R1234ze and a mixture of R32 (90% molar concentration) and R125 (10% molar concentration). Baseline experiments were performed on a window unit charged with R410A. The ORNL Heat Pump Design Model was calibrated with the baseline data and was used to assess the comparative performance of the WAC with alternative refrigerants. The paper discusses the advantages and disadvantages of each refrigerants and their suitability for window air conditioners.

  9. Application issues for large-area electrochromic windows incommercial buildings

    SciTech Connect (OSTI)

    Lee, Eleanor S.; DiBartolomeo, D.L.

    2000-05-01T23:59:59.000Z

    Projections of performance from small-area devices to large-area windows and enterprise marketing have created high expectations for electrochromic glazings. As a result, this paper seeks to precipitate an objective dialog between material scientists and building-application scientists to determine whether actual large-area electrochromic devices will result in significant performance benefits and what material improvements are needed, if any, to make electrochromics more practical for commercial building applications. Few in-situ tests have been conducted with large-area electrochromic windows applied in buildings. This study presents monitored results from a full-scale field test of large-area electrochromic windows to illustrate how this technology will perform in commercial buildings. The visible transmittance (Tv) of the installed electrochromic ranged from 0.11 to 0.38. The data are limited to the winter period for a south-east-facing window. The effect of actual device performance on lighting energy use, direct sun control, discomfort glare, and interior illumination is discussed. No mechanical system loads were monitored. These data demonstrate the use of electrochromics in a moderate climate and focus on the most restrictive visual task: computer use in offices. Through this small demonstration, we were able to determine that electrochromic windows can indeed provide unmitigated transparent views and a level of dynamic illumination control never before seen in architectural glazing materials. Daily lighting energy use was 6-24 percent less compared to the 11 percent-glazing, with improved interior brightness levels. Daily lighting energy use was 3 percent less to 13 percent more compared to the 38 percent-glazing, with improved window brightness control. The electrochromic window may not be able to fulfill both energy-efficiency and visual comfort objectives when low winter direct sun is present, particularly for computer tasks using cathode-ray tube (CRT) displays. However, window and architectural design as well as electrochromic control options are suggested as methods to broaden the applicability of electrochromics for commercial buildings. Without further modification, its applicability is expected to be limited during cold winter periods due to its slow switching speed.

  10. Optimized ECR plasma apparatus with varied microwave window thickness

    DOE Patents [OSTI]

    Berry, L.A.

    1995-11-14T23:59:59.000Z

    The present invention describes a technique to control the radial profile of microwave power in an ECR plasma discharge. In order to provide for a uniform plasma density to a specimen, uniform energy absorption by the plasma is desired. By controlling the radial profile of the microwave power transmitted through the microwave window of a reactor, the profile of the transmitted energy to the plasma can be controlled in order to have uniform energy absorption by the plasma. An advantage of controlling the profile using the window transmission characteristics is that variations to the radial profile of microwave power can be made without changing the microwave coupler or reactor design. 9 figs.

  11. HLW Glass Studies: Development of Crystal-Tolerant HLW Glasses

    SciTech Connect (OSTI)

    Matyas, Josef; Huckleberry, Adam R.; Rodriguez, Carmen P.; Lang, Jesse B.; Owen, Antionette T.; Kruger, Albert A.

    2012-04-02T23:59:59.000Z

    In our study, a series of lab-scale crucible tests were performed on designed glasses of different compositions to further investigate and simulate the effect of Cr, Ni, Fe, Al, Li, and RuO2 on the accumulation rate of spinel crystals in the glass discharge riser of the HLW melter. The experimental data were used to expand the compositional region covered by an empirical model developed previously (Matyáš et al. 2010b), improving its predictive performance. We also investigated the mechanism for agglomeration of particles and impact of agglomerates on accumulation rate. In addition, the TL was measured as a function of temperature and composition.

  12. Glass and Glass Products (2010 MECS) | Department of Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation ProposedUsingFun with Big Sky LearningGet Assistance GetGiant ProteaseGlass and Glass Products

  13. Polycrystalline CdTe Solar Cells on Buffered Commercial TCO-Coated Glass with Efficiencies Above 15%

    SciTech Connect (OSTI)

    Banai, R.; Blissett, C.; Buurma, C.; Colegrove, E.; Bechmann, P.; Ellsworth, J.; Morley, M.; Barnes, S.; Lennon, C.; Gilmore, C.; Dhere, R.; Bergeson, J.; Scott, M.; Gessert, T.

    2011-01-01T23:59:59.000Z

    EPIR Technologies, Inc. reports the production of thin film polycrystalline CdTe devices with National Renewable Energy Laboratory (NREL)-verified efficiencies above 15%. While previous reporting of high efficiency poly-CdTe solar cells utilized high-temperature technical glass, EPIR's cells were produced on commercially-available conductive glass. The devices exhibit fill factors up to 77% and short-circuit current densities around 24 mA/cm{sup 2}. EPIR developed a robust process for producing thin film CdTe solar cells through implementation of a high resistivity SnO{sub 2} buffer layer and optimization of the CdS window layer thickness. The effects of the high resistivity buffer layer on device performance were investigated, demonstrating improved overall performance and yield. To our knowledge, these are among the highest efficiencies yet reported and NREL-verified for a thin film CdTe solar cell fabricated using commercial conductive glass.

  14. Covered Product Category: Residential Windows, Doors, and Skylights

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance across a variety of product categories, including residential windows, doors, and skylights, which are an ENERGY STAR-qualified product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  15. Laboratory Performance Testing of Residential Window Air Conditioners

    SciTech Connect (OSTI)

    Winkler, J.; Booten, C.; Christensen, D.; Tomerlin, J.

    2013-03-01T23:59:59.000Z

    Window air conditioners are the dominant cooling product for residences, in terms of annual unit sales. They are inexpensive, portable and can be installed by the owner. For this reason, they are an attractive solution for supplemental cooling, for retrofitting air conditioning into a home which lacks ductwork, and for renters. Window air conditioners for sale in the United States are required to meet very modest minimum efficiency standards. Four window air conditioners' performance were tested in the Advanced HVAC Systems Laboratory on NREL's campus in Golden, CO. In order to separate and study the refrigerant system's performance, the unit's internal leakage pathways, the unit's fanforced ventilation, and the leakage around the unit resulting from installation in a window, a series of tests were devised that focused on each aspect of the unit's performance. These tests were designed to develop a detailed performance map to determine whole-house performance in different climates. Even though the test regimen deviated thoroughly from the industry-standard ratings test, the results permit simple calculation of an estimated rating for both capacity and efficiency that would result from a standard ratings test. Using this calculation method, it was found that the three new air conditioners' measured performance was consistent with their ratings. This method also permits calculation of equivalent SEER for the test articles. Performance datasets were developed across a broad range of indoor and outdoor operating conditions, and used them to generate performance maps.

  16. Energy Gaining Windows for Residential Buildings Jesper Kragh, Assistant Professor,

    E-Print Network [OSTI]

    season. It is assumed that in northern cold climates all of the solar gain during the heating season can profiles, solar gain, net energy gain, low energy houses SUMMARY: This paper presents some of the research buildings. The net energy gain of windows is the solar gain minus the heat loss integrated over the heating

  17. Intermittent and sustained periodic windows in networked chaotic Rössler oscillators

    SciTech Connect (OSTI)

    He, Zhiwei; Sun, Yong [Wuhan Center for Magnetic Resonance, State Key Laboratory of Magnetic Resonance and Atomic and Molecular Physics, Wuhan Institute of Physics and Mathematics, Chinese Academy of Sciences, Wuhan 430071 (China) [Wuhan Center for Magnetic Resonance, State Key Laboratory of Magnetic Resonance and Atomic and Molecular Physics, Wuhan Institute of Physics and Mathematics, Chinese Academy of Sciences, Wuhan 430071 (China); University of the Chinese Academy of Sciences, Beijing 100049 (China); Zhan, Meng, E-mail: zhanmeng@wipm.ac.cn [Wuhan Center for Magnetic Resonance, State Key Laboratory of Magnetic Resonance and Atomic and Molecular Physics, Wuhan Institute of Physics and Mathematics, Chinese Academy of Sciences, Wuhan 430071 (China)] [Wuhan Center for Magnetic Resonance, State Key Laboratory of Magnetic Resonance and Atomic and Molecular Physics, Wuhan Institute of Physics and Mathematics, Chinese Academy of Sciences, Wuhan 430071 (China)

    2013-12-15T23:59:59.000Z

    Route to chaos (or periodicity) in dynamical systems is one of fundamental problems. Here, dynamical behaviors of coupled chaotic Rössler oscillators on complex networks are investigated and two different types of periodic windows with the variation of coupling strength are found. Under a moderate coupling, the periodic window is intermittent, and the attractors within the window extremely sensitively depend on the initial conditions, coupling parameter, and topology of the network. Therefore, after adding or removing one edge of network, the periodic attractor can be destroyed and substituted by a chaotic one, or vice versa. In contrast, under an extremely weak coupling, another type of periodic window appears, which insensitively depends on the initial conditions, coupling parameter, and network. It is sustained and unchanged for different types of network structure. It is also found that the phase differences of the oscillators are almost discrete and randomly distributed except that directly linked oscillators more likely have different phases. These dynamical behaviors have also been generally observed in other networked chaotic oscillators.

  18. Dell recommends Windows 7. Students get the best price

    E-Print Network [OSTI]

    Almor, Amit

    Dell recommends Windows® 7. Students get the best price on consumer PCs from Dell* If you find a better price on your day of purchase, contact a Dell University specialist and we will beat that price come in small packages. DellTM XPSTM 14z Dell University Price$ 99999 ® 7 Home Premium VV Get

  19. Windows on Computer Science Department of Computer and Information Science

    E-Print Network [OSTI]

    Fang, Shiaofen

    1 CSCI 120 Windows on Computer Science Department of Computer and Information Science IUPUI What is Computer Science? Is Computer Science the study of computers (Building computers, and writing computer programs) ? Computer Science is no more about computers than astronomy is about telescopes, or biology

  20. The In uence of Windowing on Time Delay Estimates

    E-Print Network [OSTI]

    Maryland at College Park, University of

    'Ruanaidh Siemens Corporate Research 755 College Road East Princeton , NJ 08540 rvbalan,rosca,rickard,oruanaidh@scr.siemens of frequencies. Such a relation holds true when the Fourier transform is used to go into the frequency domain. However, in practice, one has to use the windowed Fourier transform to obtain the frequency domain

  1. The Influence of Windowing on Time Delay Estimates

    E-Print Network [OSTI]

    Balan, Radu V.

    O'Ruanaidh Siemens Corporate Research 755 College Road East Princeton , NJ 08540 rvbalan,rosca,rickard,oruanaidh@scr.siemens of frequencies. Such a relation holds true when the Fourier transform is used to go into the frequency domain. However, in practice, one has to use the windowed Fourier transform to obtain the frequency domain

  2. Instruction-Window Power Reduction Using Data Dependence Metric

    E-Print Network [OSTI]

    Lee, Hsien-Hsin "Sean"

    power savings, and with an average performance loss of a very modest 1.9%. I. INTRODUCTION NewInstruction-Window Power Reduction Using Data Dependence Metric Ziad Youssfi and Michael Shanblatt Department of Electrical and Computer Engineering Michigan State University East Lansing, MI 48824 ziad

  3. OPERATING TEMPERATURE WINDOWS FOR FUSION REACTOR STRUCTURAL MATERIALS

    E-Print Network [OSTI]

    California at Los Angeles, University of

    OPERATING TEMPERATURE WINDOWS FOR FUSION REACTOR STRUCTURAL MATERIALS S.J. Zinkle1 and N.M. Ghoniem reactor structural materials: four reduced-activation structural materials (oxide-dispersion- strengthened operating temperature limit of structural materials is determined by one of four factors, all of which

  4. DO NOT INCLUDE: flatten cardboard staples, tape & envelope windows ok

    E-Print Network [OSTI]

    Wolfe, Patrick J.

    / bottles Metal items other than cans/foil Napkins Paper towels Plastic bags Plastic films Plastic utensilsDO NOT INCLUDE: flatten cardboard staples, tape & envelope windows ok Aerosol cans Books Bottle, PDAs, inkjet cartridges, CFL bulbs (cushioned, sealed in plastic) computers, printers, printer

  5. EMC PERSPECTIVE: THE POWER OF WINDOWS SERVER 2012 AND EMC

    E-Print Network [OSTI]

    Chaudhuri, Surajit

    EMC PERSPECTIVE: THE POWER OF WINDOWS SERVER 2012 AND EMC INFRASTRUCTURE FOR MICROSOFT PRIVATE and storage optimization features of intelligent storage arrays, such as the EMC® Symmetrix® VMAX® storage family, the EMC® VNX® series, and the EMC® Isilon® scale-out NAS family. With new technologies

  6. Thermal and Structural Analysis of Targets and Windows

    E-Print Network [OSTI]

    McDonald, Kirk

    Thermal and Structural Analysis of Targets and Windows Materials, Irradiation Data and Fracture) = EDD/Cp Applied Thermal Stress Pa CTE*E*DeltaT Thermal Resistance Rts=UTS/(CTE*E *DeltaT) Thermal Shock 1147 1.16E+09 0.984 7445 Candidate Materials - Young's Modulus, UTS, Delta T, Thermal Stress

  7. T-547: Microsoft Windows Human Interface Device (HID) Vulnerability

    Broader source: Energy.gov [DOE]

    Microsoft Windows does not properly warn the user before enabling additional Human Interface Device (HID) functionality over USB, which allows user-assisted attackers to execute arbitrary programs via crafted USB data, as demonstrated by keyboard and mouse data sent by malware on a Smartphone that the user connected to the computer.

  8. Internet Explorer 7 on Windows Vista: Obtaining MIT Certificates

    E-Print Network [OSTI]

    Barton, Paul I.

    : A separate certificate password is not necessary for IE7 on Vista; the certificate is protected by your web services at MIT with IE7 on Windows Vista, three types of MIT web certificates are needed: · MIT servers · MIT Client Certificate, needed in IE7 on Vista to generate the personal certificate · MIT

  9. Effect of furnace atmosphere on E-glass foaming

    E-Print Network [OSTI]

    Kim, D. S.; Dutton, Bryan C.; Hrma, Pavel R.; Pilon, Laurent

    2006-01-01T23:59:59.000Z

    oxy-fired furnaces. E-glass foams were generated in a fused-81.05.K 1. Introduction Glass foams generated in glass-that the stability of E-glass foam decreased with increasing

  10. Structure glass technology : systems and applications

    E-Print Network [OSTI]

    Leitch, Katherine K. (Katherine Kristen)

    2005-01-01T23:59:59.000Z

    Glass cannot compete with steel in terms of strength or durability, but it is the only structural material that offers the highly sought after qualities of translucency and transparency. The use of glass has evolved from ...

  11. The Huge, Blue, Jesus Glass Statue

    E-Print Network [OSTI]

    Robbins, Joanna

    2013-01-01T23:59:59.000Z

    Later, I found a huge, blue, glass statue of Jesus stuffedOF CALIFORNIA RIVERSIDE The Huge, Blue, Jesus Glass Statue Aeyes as RED And wrote down BLUE for your hair. I had to fix

  12. Heating-induced glass-glass and glass-liquid transformations in computer simulations of water

    SciTech Connect (OSTI)

    Chiu, Janet; Giovambattista, Nicolas [Department of Physics, Brooklyn College of the City University of New York, Brooklyn, New York 11210 (United States)] [Department of Physics, Brooklyn College of the City University of New York, Brooklyn, New York 11210 (United States); Starr, Francis W. [Department of Physics, Wesleyan University, Middletown, Connecticut 06459 (United States)] [Department of Physics, Wesleyan University, Middletown, Connecticut 06459 (United States)

    2014-03-21T23:59:59.000Z

    Water exists in at least two families of glassy states, broadly categorized as the low-density (LDA) and high-density amorphous ice (HDA). Remarkably, LDA and HDA can be reversibly interconverted via appropriate thermodynamic paths, such as isothermal compression and isobaric heating, exhibiting first-order-like phase transitions. We perform out-of-equilibrium molecular dynamics simulations of glassy water using the ST2 model to study the evolution of LDA and HDA upon isobaric heating. Depending on pressure, glass-to-glass, glass-to-crystal, glass-to-vapor, as well as glass-to-liquid transformations are found. Specifically, heating LDA results in the following transformations, with increasing heating pressures: (i) LDA-to-vapor (sublimation), (ii) LDA-to-liquid (glass transition), (iii) LDA-to-HDA-to-liquid, (iv) LDA-to-HDA-to-liquid-to-crystal, and (v) LDA-to-HDA-to-crystal. Similarly, heating HDA results in the following transformations, with decreasing heating pressures: (a) HDA-to-crystal, (b) HDA-to-liquid-to-crystal, (c) HDA-to-liquid (glass transition), (d) HDA-to-LDA-to-liquid, and (e) HDA-to-LDA-to-vapor. A more complex sequence may be possible using lower heating rates. For each of these transformations, we determine the corresponding transformation temperature as function of pressure, and provide a P-T “phase diagram” for glassy water based on isobaric heating. Our results for isobaric heating dovetail with the LDA-HDA transformations reported for ST2 glassy water based on isothermal compression/decompression processes [Chiu et al., J. Chem. Phys. 139, 184504 (2013)]. The resulting phase diagram is consistent with the liquid-liquid phase transition hypothesis. At the same time, the glass phase diagram is sensitive to sample preparation, such as heating or compression rates. Interestingly, at least for the rates explored, our results suggest that the LDA-to-liquid (HDA-to-liquid) and LDA-to-HDA (HDA-to-LDA) transformation lines on heating are related, both being associated with the limit of kinetic stability of LDA (HDA)

  13. Classification of oxide glasses: A polarizability approach

    SciTech Connect (OSTI)

    Dimitrov, Vesselin [Department of Silicate Technology, University of Chemical Technology and Metallurgy, 8 Kl. Ohridski Blvd., Sofia 1756 (Bulgaria); Komatsu, Takayuki [Department of Chemistry, The Nagaoka University of Technology, 1603-1 Kamitomioka-cho, Nagaoka-shi, Niigata-ken 940-2188 (Japan)]. E-mail: komatsu@chem.nagaokaut.ac.jp

    2005-03-15T23:59:59.000Z

    A classification of binary oxide glasses has been proposed taking into account the values obtained on their refractive index-based oxide ion polarizability {alpha}{sub O2-}(n{sub 0}), optical basicity {lambda}(n{sub 0}), metallization criterion M(n{sub 0}), interaction parameter A(n{sub 0}), and ion's effective charges as well as O1s and metal binding energies determined by XPS. Four groups of oxide glasses have been established: glasses formed by two glass-forming acidic oxides; glasses formed by glass-forming acidic oxide and modifier's basic oxide; glasses formed by glass-forming acidic and conditional glass-forming basic oxide; glasses formed by two basic oxides. The role of electronic ion polarizability in chemical bonding of oxide glasses has been also estimated. Good agreement has been found with the previous results concerning classification of simple oxides. The results obtained probably provide good basis for prediction of type of bonding in oxide glasses on the basis of refractive index as well as for prediction of new nonlinear optical materials.

  14. The corrosion behavior of DWPF glasses

    SciTech Connect (OSTI)

    Ebert, W.L.; Bates, J.K. [Argonne National Lab., IL (United States). Chemical Technology Div.

    1995-06-01T23:59:59.000Z

    The authors analyzed the corroded surfaces of reference glasses developed for the Defense Waste Processing Facility (DWPF) to characterize their corrosion behavior. The corrosion mechanism of nuclear waste glasses must be known in order to provide source terms describing radionuclide release for performance assessment calculations. Different DWPF reference glasses were corroded under conditions that highlighted various aspects of the corrosion process and led to different extents of corrosion. The glasses corroded by similar mechanisms, and a phenomenological description of their corrosion behavior is presented here. The initial leaching of soluble glass components results in the formation of an amorphous gel layer on the glass surface. The gel layer is a transient phase that transforms into a layer of clay crystallites, which equilibrates with the solution as corrosion continues. The clay layer does not act as a barrier to either water penetration or glass dissolution, which continues beneath it, and may eventually separate from the glass. Solubility limits for glass components may be established by the eventual precipitation of secondary phases; thus, corrosion of the glass becomes controlled by the chemical equilibrium between the solution and the assemblage of secondary phases. In effect, the solution is an intermediate phase through which the glass transforms to an energetically more favorable assemblage of phases. Implications regarding the prediction of long-term glass corrosion behavior are discussed.

  15. DURABLE GLASS FOR THOUSANDS OF YEARS

    SciTech Connect (OSTI)

    Jantzen, C.

    2009-12-04T23:59:59.000Z

    The durability of natural glasses on geological time scales and ancient glasses for thousands of years is well documented. The necessity to predict the durability of high level nuclear waste (HLW) glasses on extended time scales has led to various thermodynamic and kinetic approaches. Advances in the measurement of medium range order (MRO) in glasses has led to the understanding that the molecular structure of a glass, and thus the glass composition, controls the glass durability by establishing the distribution of ion exchange sites, hydrolysis sites, and the access of water to those sites. During the early stages of glass dissolution, a 'gel' layer resembling a membrane forms through which ions exchange between the glass and the leachant. The hydrated gel layer exhibits acid/base properties which are manifested as the pH dependence of the thickness and nature of the gel layer. The gel layer ages into clay or zeolite minerals by Ostwald ripening. Zeolite mineral assemblages (higher pH and Al{sup 3+} rich glasses) may cause the dissolution rate to increase which is undesirable for long-term performance of glass in the environment. Thermodynamic and structural approaches to the prediction of glass durability are compared versus Ostwald ripening.

  16. Identifying the Bose glass phase

    E-Print Network [OSTI]

    R. Pugatch; N. Bar-gill; N. Katz; E. Rowen; N. Davidson

    2006-07-28T23:59:59.000Z

    Introducing disorder into the Bose-Hubbard model at integer fillings leads to a Bose glass phase, along with the Mott insulator and superfluid phases. We suggest a new order parameter: the determinant of the one body density matrix, which is nonzero only within the Mott-insulator phase. Alongside the superfluid fraction, it is then possible to distinguish the three phases. The Bose glass phase is the only phase which has vanishing determinant and superfluid fraction. The vanishing of the determinant in the Bose glass phase occurs due to the partial fragmentation of the condensate into localized fragments, each with zero superfluid response, which implies the presence of unoccupied sites and hence the presence of lines of zeros in the one body density matrix. In the superfluid phase, the determinant vanish for another reason - due to the macroscopic occupation of a single particle state. Finally, we suggest the enhancement of the three body decay rate in the Bose glass phase, as an experimental indicator for the presence of localized fragments.

  17. Experimental evaluation of 350 MHz RF accelerator windows for the low energy demonstration accelerator

    SciTech Connect (OSTI)

    Cummings, K.; Rees, D.; Roybal, W. [and others

    1997-09-01T23:59:59.000Z

    Radio frequency (RF) windows are historically a point where failure occurs in input power couplers for accelerators. To obtain a reliable, high-power, 350 MHz RF window for the Low Energy Demonstration Accelerator (LEDA) project of the Accelerator Production of Tritium program, RF windows prototypes from different vendors were tested. Experiments were performed to evaluate the RF windows by the vendors to select a window for the LEDA project. The Communications and Power, Inc. (CPI) windows were conditioned to 445 kW in roughly 15 hours. At 445 kW a window failed, and the cause of the failure will be presented. The English Electronic Valve, Inc. (EEV) windows were conditioned to 944 kW in 26 hours and then tested at 944 kW for 4 hours with no indication of problems.

  18. Design of an energy efficient and economical actuator for automobile windows

    E-Print Network [OSTI]

    Durand, Keith (Keith V.)

    2007-01-01T23:59:59.000Z

    This thesis describes the design and analysis of an efficient, yet low cost, drum driven window actuation system for an automotive power window. The design uses a novel approach that involves using cables to both actuate ...

  19. Building America Webinar: Low-E Storms: The Next Big Thing in Window Retrofits

    Broader source: Energy.gov [DOE]

    This Building America webinar presented a new and improved low-e storm window that boasts a combination of curb appeal and energy efficiency, all for a fraction of the cost of window replacement, on Sept. 9, 2014.

  20. Key Elements of and Materials Performance Targets for Highly Insulating Window Frames

    E-Print Network [OSTI]

    Gustavsen, Arild

    2012-01-01T23:59:59.000Z

    in light green. 2.5 Window Frame E (PVC) Window frame Eis polyvinyl chloride (PVC). We performed calculations forspacer = 0.25?0.1 W/(mK) ? pvc = 0.9 W/(mK), ? eff. ,spacer

  1. How Do You Use Daylighting While Reducing Excess Heat from Windows...

    Broader source: Energy.gov (indexed) [DOE]

    through these windows in the summer. How do you use daylighting while reducing excess heat from windows? Each Thursday, you have the chance to share your thoughts on a question...

  2. Window-Related Energy Consumption in the US Residential and Commercial Building Stock

    E-Print Network [OSTI]

    Apte, Joshua; Arasteh, Dariush

    2008-01-01T23:59:59.000Z

    Building Heating Loads (Trillion BTU/yr) Total BuildingCooling Loads (Trillion BTU/yr) Non. Wind Infilt SHGC Wind.Energy Consumption (Trillion BTU/yr) Area, Window Window

  3. Window Spacers and Edge Seals in Insulating Glass Units: A State-of-the-Art Review and Future Perspectives

    E-Print Network [OSTI]

    Bergh, Sofie Van Den

    2014-01-01T23:59:59.000Z

    International) AG, TruSeal Technologies Edgetech GlasslamSeals, Science and Technology of Building Seals, Sealants,of Canada, Construction Technology Update no. 58 (2003) 1-4.

  4. Installation of Window Air Conditioners Page 1 of 2 Virginia Polytechnic Institute and State University No. 5705 Rev.: 3

    E-Print Network [OSTI]

    Buehrer, R. Michael

    Installation of Window Air Conditioners Page 1 of 2 Virginia Polytechnic Institute and State __________________________________________________________________________________ Subject: Installation of Window Air Conditioners........................................................................................................................................1 1. Purpose To define a policy for installation of window air conditioners that avoids exterior

  5. Integrated self-cleaning window assembly for optical transmission in combustion environments

    DOE Patents [OSTI]

    Kass, Michael D [Oak Ridge, TN

    2007-07-24T23:59:59.000Z

    An integrated window design for optical transmission in combustion environments is described. The invention consists of an integrated optical window design that prevents and removes the accumulation of carbon-based particulate matter and gaseous hydrocarbons through a combination of heat and catalysis. These windows will enable established optical technologies to be applied to combustion environments and their exhaust systems.

  6. Completed April 30, 2004. LBNL-54966. The Energy-Savings Potential of Electrochromic Windows

    E-Print Network [OSTI]

    % market penetration level in that year. Keywords: Building energy-efficiency, electrochromic windows1 Completed April 30, 2004. LBNL-54966. The Energy-Savings Potential of Electrochromic Windows Road, Berkeley, CA 94720, USA Abstract Switchable electrochromic (EC) windows have been projected

  7. Lighting energy savings potential of split-pane electrochromic windows controlled for

    E-Print Network [OSTI]

    LBNL-6152E Lighting energy savings potential of split- pane electrochromic windows controlled potential of split-pane electrochromic windows controlled for daylighting with visual comfort L was conducted to evaluate lighting energy savings of split-pane electrochromic (EC) windows controlled

  8. A First-Generation Prototype Dynamic Residential Window Christian Kohler, Howdy Goudey, and Dariush Arasteh

    E-Print Network [OSTI]

    October 26, 2004 Abstract We present the concept for a "smart" highly efficient dynamic window in residential buildings. We describe a prototype dynamic window that relies on an internal shade, which deploys technology have significantly reduced window-related energy use and peak demand in residential buildings

  9. Analysis of a Fabric/Desiccant Window Cavity Dehumidifier

    E-Print Network [OSTI]

    Hunn, B. D.; Grasso, M. M.; Vadlamani, V.

    1994-01-01T23:59:59.000Z

    design of such a system was developed and modeled to determine its performance under typical load and weather conditions. The design includes a moving fabric/desiccant belt installed in a window cavity, cwpled with a regenerative heat exchanger, which... energy, but could be supplied by an auxiliary source. A regenerative heat exchanger exmts heat from the hot exhaust of the dehumidification channel and preheats the incoming regeneration air slream. This system can be conf~gured to process two...

  10. Pressurized heat treatment of glass ceramic

    DOE Patents [OSTI]

    Kramer, D.P.

    1984-04-19T23:59:59.000Z

    A method of producing a glass-ceramic having a specified thermal expansion value is disclosed. The method includes the step of pressurizing the parent glass material to a predetermined pressure during heat treatment so that the glass-ceramic produced has a specified thermal expansion value. Preferably, the glass-ceramic material is isostatically pressed. A method for forming a strong glass-ceramic to metal seal is also disclosed in which the glass-ceramic is fabricated to have a thermal expansion value equal to that of the metal. The determination of the thermal expansion value of a parent glass material placed in a high-temperature environment is also used to determine the pressure in the environment.

  11. Durability of Silicate Glasses: An Historical Approach

    SciTech Connect (OSTI)

    Farges, Francois; /Museum Natl. Hist. Natur. /Stanford U., Geo. Environ. Sci.; Etcheverry, Marie-Pierre; /Marne la Vallee U.; Haddi, Amine; /Marne la Valle U.; Trocellier,; /Saclay; Curti, Enzo; /PSI, Villigen; Brown, Gordon E., Jr.; /SLAC, SSRL

    2007-01-02T23:59:59.000Z

    We present a short review of current theories of glass weathering, including glass dissolution, and hydrolysis of nuclear waste glasses, and leaching of historical glasses from an XAFS perspective. The results of various laboratory leaching experiments at different timescales (30 days to 12 years) are compared with results for historical glasses that were weathered by atmospheric gases and soil waters over 500 to 3000 years. Good agreement is found between laboratory experiments and slowly leached historical glasses, with a strong enrichment of metals at the water/gel interface. Depending on the nature of the transition elements originally dissolved in the melt, increasing elemental distributions are expected to increase with time for a given glass durability context.

  12. Development of a cooled microwave window. CRADA final report for CRADA Number Y-1293-0200

    SciTech Connect (OSTI)

    Bell, G.L.; Bigelow, T.S.; Leitch, R.M.; Berry, L.A. [Lockheed Martin Energy Systems, Inc., Oak Ridge, TN (United States); Holber, W.M. [Applied Science and Technology, Inc., Woburn, MA (United States)

    1995-04-06T23:59:59.000Z

    The objective of this Cooperative Research and Development project (CRADA) was to generate a new design for a microwave vacuum window to be used with ASTeX Corporation plasma processing equipment. This vacuum window allows transmission of microwave power from an input waveguide into a vacuum chamber for creation of plasma using the electron cyclotron resonance process. Requirements for the window design are: higher power capability, improved resistance to chemical attack, and physical compatibility with previous window models. In these applications, a significant portion of the input power is deposited in the window by plasma bombardment so the window must remove a great deal of heat to remain at a reliable operating temperature. A power level increase from 1.5 kW to 5 kW is desired by ASTeX for the new window which must have {approximately} 120 mm diameter and be compatible with existing hardware. New applications for these processing systems are being developed by ASTeX; these require the use of highly reactive fluorine plasmas which can rapidly etch some window materials. Therefore, the use of a fluorine compatible window ceramic is required. Two new window designs were investigated using advanced window-modeling techniques and low-power laboratory testing. It was determined that both concepts were capable of operating at significantly higher power levels than present commercial windows and would meet the CRADA design objectives. The compatibility of the window materials considered with fluorine plasmas are believed to be acceptable. ASTeX has a continuing interest in pursuing these window designs and will likely begin manufacturing design work of the improved design in the near future. There will also be a continuing effort to keep AlN ceramic manufacturers interested in improving the quality of large AlN disks. Additional window tests and development work could be performed by ORNL/MMES if a suitable funding source is available.

  13. Lid heater for glass melter

    DOE Patents [OSTI]

    Phillips, Terrance D. (617 Chestnut Ct., Aiken, SC 29803)

    1993-01-01T23:59:59.000Z

    A glass melter having a lid electrode for heating the glass melt radiantly. The electrode comprises a series of INCONEL 690 tubes running above the melt across the melter interior and through the melter walls and having nickel cores inside the tubes beginning where the tubes leave the melter interior and nickel connectors to connect the tubes electrically in series. An applied voltage causes the tubes to generate heat of electrical resistance for melting frit injected onto the melt. The cores limit heat generated as the current passes through the walls of the melter. Nickel bus connection to the electrical power supply minimizes heat transfer away from the melter that would occur if standard copper or water-cooled copper connections were used between the supply and the INCONEL 690 heating tubes.

  14. Lid heater for glass melter

    DOE Patents [OSTI]

    Phillips, T.D.

    1993-12-14T23:59:59.000Z

    A glass melter having a lid electrode for heating the glass melt radiantly. The electrode comprises a series of INCONEL 690 tubes running above the melt across the melter interior and through the melter walls and having nickel cores inside the tubes beginning where the tubes leave the melter interior and nickel connectors to connect the tubes electrically in series. An applied voltage causes the tubes to generate heat of electrical resistance for melting frit injected onto the melt. The cores limit heat generated as the current passes through the walls of the melter. Nickel bus connection to the electrical power supply minimizes heat transfer away from the melter that would occur if standard copper or water-cooled copper connections were used between the supply and the INCONEL 690 heating tubes. 3 figures.

  15. Melter Glass Removal and Dismantlement

    SciTech Connect (OSTI)

    Richardson, BS

    2000-10-31T23:59:59.000Z

    The U.S. Department of Energy (DOE) has been using vitrification processes to convert high-level radioactive waste forms into a stable glass for disposal in waste repositories. Vitrification facilities at the Savannah River Site (SRS) and at the West Valley Demonstration Project (WVDP) are converting liquid high-level waste (HLW) by combining it with a glass-forming media to form a borosilicate glass, which will ensure safe long-term storage. Large, slurry fed melters, which are used for this process, were anticipated to have a finite life (on the order of two to three years) at which time they would have to be replaced using remote methods because of the high radiation fields. In actuality the melters useable life spans have, to date, exceeded original life-span estimates. Initial plans called for the removal of failed melters by placing the melter assembly into a container and storing the assembly in a concrete vault on the vitrification plant site pending size-reduction, segregation, containerization, and shipment to appropriate storage facilities. Separate facilities for the processing of the failed melters currently do not exist. Options for handling these melters include (1) locating a facility to conduct the size-reduction, characterization, and containerization as originally planned; (2) long-term storing or disposing of the complete melter assembly; and (3) attempting to refurbish the melter and to reuse the melter assembly. The focus of this report is to look at methods and issues pertinent to size-reduction and/or melter refurbishment in particular, removing the glass as a part of a refurbishment or to reduce contamination levels (thus allowing for disposal of a greater proportion of the melter as low level waste).

  16. Building America's Low-e Storm Window Adoption Program Plan (FY2014)

    SciTech Connect (OSTI)

    Cort, Katherine A.

    2013-12-23T23:59:59.000Z

    Low emissivity (low-e) storm windows/panels appear to hold promise for effectively reducing existing home heating, ventilation, and air-conditioning (HVAC) consumption. Due to the affordability of low-e storm windows and the large numbers of existing homes that have low-performing single-pane or double-pane clear windows, a tremendous opportunity exists to provide energy savings by transforming the low-e storm window market and increasing market adoption. This report outlines U.S. Department of Energy (DOE) Building America’s planned market transformation activities in support of low-e storm window adoption during fiscal year (FY) 2014.

  17. Movable insulation. A guide to reducing heating and cooling losses through the windows in your home

    SciTech Connect (OSTI)

    Langdon, W.K.

    1980-01-01T23:59:59.000Z

    A typical house loses 25 to 30% of its heat through windows, and a house with large windows may lose as much as 50%. Numerous movable-insulation systems that will cut the heat loss through windows in half are described. Chapters are: The Energy-Responsive Dwelling, Past to Present; Window Heat Losses and Gains; Enhanced Glazing Systems; Choosing a Window-Insulation Design for Your Home; Pop-In Shutters; Thermal Curtains - Blankets that Fold; Thermal Shades - Blankets that Roll; Thermal Shutters and Folding Screens; Insulation Between Glazing and Interior Louvers; Exterior Hinged and Sliding Shutters; Sun-Shading Screens; Exterior Roll Shutters; Shutters for Skylights; Shutters for Clerestory Windows; Interior Greenhouse Insulation Systems; Exterior Insulation for Greenhouses; Movable Insulation to Assist Passive Space Heating; and Movable Insulation to Assist Solar Water Heaters. Appendices include the following: insulated shade and shutter construction; the economics of window insulation; movable insulation products, hardware, and components; further technical information; and design sources. (MCW)

  18. The Impact Of The MCU Life Extension Solvent On Sludge Batch 8 Projected Operating Windows

    SciTech Connect (OSTI)

    Peeler, D. K.; Edwards, T. B.; Stone, M. E.

    2013-08-14T23:59:59.000Z

    As a part of the Actinide Removal Process (ARP)/Modular Caustic Side Solvent Extraction Unit (MCU) Life Extension Project, a next generation solvent (NGS) and a new strip acid will be deployed. The strip acid will be changed from dilute nitric acid to dilute boric acid (0.01 M). Because of these changes, experimental testing or evaluations with the next generation solvent are required to determine the impact of these changes (if any) to Chemical Process Cell (CPC) activities, glass formulation strategies, and melter operations at the Defense Waste Processing Facility (DWPF). The introduction of the dilute (0.01M) boric acid stream into the DWPF flowsheet has a potential impact on glass formulation and frit development efforts since B2O3 is a major oxide in frits developed for DWPF. Prior knowledge of this stream can be accounted for during frit development efforts but that was not the case for Sludge Batch 8 (SB8). Frit 803 has already been recommended and procured for SB8 processing; altering the frit to account for the incoming boron from the strip effluent (SE) is not an option for SB8. Therefore, the operational robustness of Frit 803 to the introduction of SE including its compositional tolerances (i.e., up to 0.0125M boric acid) is of interest and was the focus of this study. The primary question to be addressed in the current study was: What is the impact (if any) on the projected operating windows for the Frit 803 – SB8 flowsheet to additions of B2O3 from the SE in the Sludge Receipt and Adjustment Tank (SRAT)? More specifically, will Frit 803 be robust to the potential compositional changes occurring in the SRAT due to sludge variation, varying additions of ARP and/or the introduction of SE by providing access to waste loadings (WLs) of interest to DWPF? The Measurement Acceptability Region (MAR) results indicate there is very little, if any, impact on the projected operating windows for the Frit 803 – SB8 system regardless of the presence or absence of ARP and SE (up to 2 wt% B2O3 contained in the SRAT and up to 2000 gallons of ARP). It should be noted that 0.95 wt% B2O3 is the nominal projected concentration in the SRAT based on a 0.0125M boric acid flowsheet with 70,000 liters of SE being added to the SRAT. The impact on CPC processing of a 0.01M boric acid solution for elution of cesium during Modular Caustic Side Solvent Extraction Unit (MCU) processing has previously been evaluated by the Savannah River National Laboratory (SRNL). Increasing the acid strength to 0.0125M boric acid to account for variations in the boric acid strength has been reviewed versus the previous evaluation. The amount of acid from the boric acid represented approximately 5% of the total acid during the previous evaluation. An increase from 0.01 to 0.0125M boric acid represents a change of approximately 1.3% which is well within the error of the acid calculation. Therefore, no significant changes to CPC processing (hydrogen generation, metal solubilities, rheological properties, REDOX control, etc.) are expected from an increase in allowable boric acid concentration from 0.01M to 0.0125M.

  19. Theoretical Predictions and Experimental Assessments of the Performance of Alumina RF Windows

    SciTech Connect (OSTI)

    Karen Ann Cummings

    1998-07-01T23:59:59.000Z

    Radio frequency (RF) windows are the most likely place for catastrophic failure to occur in input power couplers for particle accelerators. Reliable RF windows are essential for the success of the Accelerator Production of Tritium (APT) program because there are over 1000 windows on the accelerator, and it takes more than one day to recover from a window failure. The goals of this research are to analytically predict the lifetime of the windows, to develop a conditioning procedure, and to evaluate the performance of the RF windows. The analytical goal is to predict the lifetime of the windows. The probability of failure is predicted by the combination of a finite element model of the window, Weibull probabilistic analysis, and fracture mechanics. The window assembly is modeled in a finite element electromagnetic code in order to calculate the electric fields in the window. The geometry (i.e. mesh) and electric fields are input into a translator program to generate the mesh and boundary conditions for a finite element thermal structural code. The temperatures and stresses are determined in the thermal/structural code. The geometry and thermal structural results are input into another translator program to generate an input file for the reliability code. Material, geometry and service data are also input into the reliability code. To obtain accurate Weibull and fatigue data for the analytical model, four point bend tests were done. The analytical model is validated by comparing the measurements to the calculations. The lifetime of the windows is then determined using the reliability code. The analytical model shows the window has a good thermal mechanical design and that fast fracture is unlikely to occur below a power level of 9 Mw. The experimental goal is to develop a conditioning procedure and evaluate the performance of RF windows. During the experimental evaluation, much was learned about processing of the windows to improve the RF performance. Methods of processing included grit blasting and using various coatings.

  20. Current status of the GLASS code

    SciTech Connect (OSTI)

    Hootman, H.E. (Westinghouse Savannah River Co., Aiken, SC (United States)); Honeck, H.C. (Computer Application Technology, Inc., Aiken, SC (United States))

    1991-01-01T23:59:59.000Z

    This paper summarizes the current status of the Generalized Lattice Analysis SubSystem (GLASS) computer code and its supporting cross section libraries. GLASS was developed at the Savannah River Site (SRS) in the early 1970's. The GLASS code has been instrumental in supporting safe Heavy Water Reactor (HWR) operations and predicting material production at SRS for more than 20 years. The Department of Energy Office of New Production Reactors (ONPR) program has chosen to use the GLASS code for the design of the HWR option of the New Production Reactor (NPR). A substantial body of validation calculations have been performed and additional validation calculations will be performed to qualify the new GLASS multigroup cross section libraries derived from the ENDF/B-5 and 6 nuclear data files. Several improvements to the code are in progress. Many other improvements are planned to bring GLASS up to modern physics and compute technology.

  1. Current status of the GLASS code

    SciTech Connect (OSTI)

    Hootman, H.E. [Westinghouse Savannah River Co., Aiken, SC (United States); Honeck, H.C. [Computer Application Technology, Inc., Aiken, SC (United States)

    1991-12-31T23:59:59.000Z

    This paper summarizes the current status of the Generalized Lattice Analysis SubSystem (GLASS) computer code and its supporting cross section libraries. GLASS was developed at the Savannah River Site (SRS) in the early 1970`s. The GLASS code has been instrumental in supporting safe Heavy Water Reactor (HWR) operations and predicting material production at SRS for more than 20 years. The Department of Energy Office of New Production Reactors (ONPR) program has chosen to use the GLASS code for the design of the HWR option of the New Production Reactor (NPR). A substantial body of validation calculations have been performed and additional validation calculations will be performed to qualify the new GLASS multigroup cross section libraries derived from the ENDF/B-5 and 6 nuclear data files. Several improvements to the code are in progress. Many other improvements are planned to bring GLASS up to modern physics and compute technology.

  2. Reactive cluster model of metallic glasses

    SciTech Connect (OSTI)

    Jones, Travis E. [Molecular Theory Group, Colorado School of Mines, Golden, Colorado 80401 (United States) [Molecular Theory Group, Colorado School of Mines, Golden, Colorado 80401 (United States); School of Physics, The University of Sydney, Sydney, New South Wales 2006 (Australia); Miorelli, Jonathan; Eberhart, Mark E. [Molecular Theory Group, Colorado School of Mines, Golden, Colorado 80401 (United States)] [Molecular Theory Group, Colorado School of Mines, Golden, Colorado 80401 (United States)

    2014-02-28T23:59:59.000Z

    Though discovered more than a half century ago metallic glasses remain a scientific enigma. Unlike crystalline metals, characterized by short, medium, and long-range order, in metallic glasses short and medium-range order persist, though long-range order is absent. This fact has prompted research to develop structural descriptions of metallic glasses. Among these are cluster-based models that attribute amorphous structure to the existence of clusters that are incommensurate with crystalline periodicity. Not addressed, however, are the chemical factors stabilizing these clusters and promoting their interconnections. We have found that glass formers are characterized by a rich cluster chemistry that above the glass transformation temperature promotes exchange as well as static and vibronic sharing of atoms between clusters. The vibronic mechanism induces correlated motions between neighboring clusters and we hypothesize that the distance over which these motions are correlated mediates metallic glass stability and influences critical cooling rates.

  3. Glass Property Data and Models for Estimating High-Level Waste Glass Volume

    SciTech Connect (OSTI)

    Vienna, John D.; Fluegel, Alexander; Kim, Dong-Sang; Hrma, Pavel R.

    2009-10-05T23:59:59.000Z

    This report describes recent efforts to develop glass property models that can be used to help estimate the volume of high-level waste (HLW) glass that will result from vitrification of Hanford tank waste. The compositions of acceptable and processable HLW glasses need to be optimized to minimize the waste-form volume and, hence, to save cost. A database of properties and associated compositions for simulated waste glasses was collected for developing property-composition models. This database, although not comprehensive, represents a large fraction of data on waste-glass compositions and properties that were available at the time of this report. Glass property-composition models were fit to subsets of the database for several key glass properties. These models apply to a significantly broader composition space than those previously publised. These models should be considered for interim use in calculating properties of Hanford waste glasses.

  4. Process for preparing improved silvered glass mirrors

    DOE Patents [OSTI]

    Buckwalter, C.Q. Jr.

    1980-01-28T23:59:59.000Z

    Glass mirrors having improved weathering properties are prepared by an improvement in the process for making the mirrors. The glass surface after it has been cleaned but before it is silvered, is contacted with a solution of lanthanide rare earths in addition to a sensitization solution of tin or palladium. The addition of the rare earths produces a mirror which has increased resistance to delamination of the silver from the glass surface in the presence of water.

  5. Feasibility study of broadband efficient ''water window'' source

    SciTech Connect (OSTI)

    Higashiguchi, Takeshi; Yugami, Noboru [Department of Advanced Interdisciplinary Sciences, Center for Optical Research and Education (CORE), and Optical Technology Innovation Center (OpTIC), Utsunomiya University, Yoto 7-1-2, Utsunomiya, Tochigi 321-8585 (Japan); Japan Science and Technology Agency, CREST, 4-1-8 Honcho, Kanagawa, Saitama 332-0012 (Japan); Otsuka, Takamitsu [Department of Advanced Interdisciplinary Sciences, Center for Optical Research and Education (CORE), and Optical Technology Innovation Center (OpTIC), Utsunomiya University, Yoto 7-1-2, Utsunomiya, Tochigi 321-8585 (Japan); Jiang Weihua [Department of Electrical Engineering, Nagaoka University of Technology, Kami-tomiokamachi 1603-1, Nagaoka, Niigata 940-2188 (Japan); Endo, Akira [Research Institute for Science and Engineering, Waseda University, Okubo 3-4-1, Shinjuku, Tokyo 169-8555 (Japan); Li Bowen; Dunne, Padraig; O'Sullivan, Gerry [School of Physics, University College Dublin, Belfield, Dublin 4 (Ireland)

    2012-01-02T23:59:59.000Z

    We demonstrate a table-top broadband emission water window source based on laser-produced high-Z plasmas. Resonance emission from multiply charged ions merges to produce intense unresolved transition arrays (UTAs) in the 2-4 nm region, extending below the carbon K edge (4.37 nm). Arrays resulting from n=4-n=4 transitions are overlaid with n=4-n=5 emission and shift to shorter wavelength with increasing atomic number. An outline of a microscope design for single-shot live cell imaging is proposed based on a bismuth plasma UTA source, coupled to multilayer mirror optics.

  6. Mickey Leland Energy Fellowship Report: Development of Advanced Window Coatings

    SciTech Connect (OSTI)

    Bolton, Ladena A.; Alvine, Kyle J.; Schemer-Kohrn, Alan L.

    2014-08-05T23:59:59.000Z

    Advanced fenestration technologies for light and thermal management in building applications are of great recent research interest for improvements in energy efficiency. Of these technologies, there is specific interest in advanced window coating technologies that have tailored control over the visible and infrared (IR) scattering into a room for both static and dynamic applications. Recently, PNNL has investigated novel subwavelength nanostructured coatings for both daylighting, and IR thermal management applications. Such coatings rese still in the early stages and additional research is needed in terms of scalable manufacturing. This project investigates aspects of a potential new methodology for low-cost scalable manufacture of said subwavelength coatings.

  7. Atmospheric Condensation Potential of Windows in Hot, Humid Climates

    E-Print Network [OSTI]

    El Diasty, R.; Budaiwi, I.

    . REFERENCES I. Wilson, A.G., 1973, " Condensation on Inside Window Surfaces," Canadian Building Di~esl, vol. 137, no. 2, pp 4.1-4.4. 2. DUll, G.S., 1979, " Condensation in Allics: Are Vapour Ilarriers Really the_answer? ,", Energy and Iluildings, vol. I... and Buildinl; Materials. vol. 3, no. 3, pp 135 -139 . 9. EI Diasty, R., Budaiwi, I., 1989, " Prediction of Mass Condensation Rate for Gas-Vapour Mixture Dominated by a Non-Condensable Gas," 12th Canadian Congress of ADDlied Mechanics, vol.2, pp 734 ?735...

  8. Energy-Efficient Window Treatments | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"ClickPipelinesProvedDecember 2005DepartmentDecember 2011District |Department ofEnergy andWindow

  9. Expert Meeting Report: Windows Options for New and Existing Homes

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of Inspector General Office of Audit|Department of Energy56Executive Summit onTransforming Existing Windows

  10. Denaturing Urea PAGE -Large Gel Preparation of Glass Plates

    E-Print Network [OSTI]

    Aris, John P.

    for short glass plate. Wear gloves. 3. Place long glass plate on 2 foam rectangles. Set up spacers and short32 Denaturing Urea PAGE - Large Gel Preparation of Glass Plates 1. Clean glass plates and comb pipette, add 5 drops of dichlorodimethylsilane (Aldrich D6,082-6) to 5 mls of acetone in diposable glass

  11. Compliant Glass Seals for SOFC Stacks

    SciTech Connect (OSTI)

    Chou, Y. S.; Choi, Jung-Pyung; Xu, Wei; Stephens, Elizabeth V.; Koeppel, Brian J.; Stevenson, Jeffry W.; Lara-Curzio, Edgar

    2014-04-01T23:59:59.000Z

    This report summarizes results from experimental and modeling studies performed by participants in the Solid-State Energy Conversion Alliance (SECA) Core Technology Program, which indicate that compliant glass-based seals offer a number of potential advantages over conventional seals based on de-vitrifying glasses, including reduced stresses during stack operation and thermal cycling, and the ability to heal micro-damage induced during thermal cycling. The properties and composition of glasses developed and/or investigated in these studies are reported, along with results from long-term (up to 5,800h) evaluations of seals based on a compliant glass containing ceramic particles or ceramic fibers.

  12. Introduction and Motivation Structural Model for Laminated Glass Beams Conclusions and Outlook of Laminated Glass Structures

    E-Print Network [OSTI]

    Components of Crystalline Solar Modules back sheet or glass encapsulant electrical conductor crystalline solar cells encapsulant front glass Reference: Schulze, S.-H.; Pander, M.; Naumenko, K.; Altenbach, H and Motivation Components of Thin Film Solar Modules back sheet or glass encapsulant electrical conductor thin

  13. Affordable Window Insulation with R-10/inch Rating

    SciTech Connect (OSTI)

    Jenifer Marchesi Redouane Begag; Je Kyun Lee; Danny Ou; Jong Ho Sonn; George Gould; Wendell Rhine

    2004-10-15T23:59:59.000Z

    During the performance of contract DE-FC26-00-NT40998, entitled ''Affordable Window Insulation with R-10/inch Value'', research was conducted at Aspen Aerogels, Inc. to develop new transparent aerogel materials suitable for window insulation applications. The project requirements were to develop a formulation or multiple formulations that have high transparency (85-90%) in the visible region, are hydrophobic (will not opacify with exposure to water vapor or liquid), and have at least 2% resiliency (interpreted as recoverable 2% strain and better than 5% strain to failure in compression). Results from an unrelated project showed that silica aerogels covalently bonded to organic polymers exhibit excellent mechanical properties. At the outset of this project, we believed that such a route is the best to improve mechanical properties. We have applied Design of Experiment (DOE) techniques to optimize formulations including both silica aerogels and organically modified silica aerogels (''Ormosils''). We used these DOE results to optimize formulations around the local/global optimization points. This report documents that we succeeded in developing a number of formulations that meet all of the stated criteria. We successfully developed formulations utilizing a two-step approach where the first step involves acid catalyzed hydrolysis and the second step involves base catalyzed condensation to make the gels. The gels were dried using supercritical CO{sub 2} and we were able to make 1 foot x 1 foot x 0.5 inch panels that met the criteria established.

  14. Glass Concrete Thin Sheets Reinforced with Prestressed Aramid Fabrics

    E-Print Network [OSTI]

    Meyer, Christian

    Glass Concrete Thin Sheets Reinforced with Prestressed Aramid Fabrics Gregor Vilkner Submitted Glass Concrete Thin Sheets Reinforced with Prestressed Aramid Fabrics Gregor Vilkner Thin sheet concrete presented in this work explored the possibilities of prestressing thin sheet glass concrete products

  15. SRNL POROUS WALL GLASS MICROSPHERES

    SciTech Connect (OSTI)

    Wicks, G; Leung Heung, L; Ray Schumacher, R

    2008-04-15T23:59:59.000Z

    The Savannah River National Laboratory (SRNL) has developed a new medium for storage of hydrogen and other gases. This involves fabrication of thin, Porous Walled, Hollow Glass Microspheres (PW-HGMs), with diameters generally in the range of 1 to several hundred microns. What is unique about the glass microballons is that porosity has been induced and controlled within the thin, one micron thick walls, on the scale of 10 to several thousand Angstroms. This porosity results in interesting properties including the ability to use these channels to fill the microballons with special absorbents and other materials, thus providing a contained environment even for reactive species. Gases can now enter the microspheres and be retained on the absorbents, resulting in solid-state and contained storage of even reactive species. Also, the porosity can be altered and controlled in various ways, and even used to filter mixed gas streams within a system. SRNL is involved in about a half dozen different programs involving these PW-HGMs and an overview of some of these activities and results emerging are presented.

  16. High Performance X-Ray Transmission Windows Based on Graphenic Carbon

    E-Print Network [OSTI]

    Huebner, Sebastian; Kapser, Stefan; Pahlke, Andreas; Kreupl, Franz

    2015-01-01T23:59:59.000Z

    A novel x-ray transmission window based on graphenic carbon has been developed with superior performance compared to beryllium transmission windows that are currently used in the field. Graphenic carbon in combination with an integrated silicon frame allows for a window design which does not use a mechanical support grid or additional light blocking layers. Compared to beryllium, the novel x-ray transmission window exhibits an improved transmission in the low energy region ($0.1 hbox{keV}-3 hbox{keV}$ ) while demonstrating excellent mechanical stability, as well as light and vacuum tightness. Therefore, the newly established graphenic carbon window, can replace beryllium in x-ray transmission windows with a nontoxic and abundant material. Index terms: Beryllium, Carbon, Graphene, Thin films, X-ray applications, X-ray detectors

  17. Window-Related Energy Consumption in the US Residential andCommercial Building Stock

    SciTech Connect (OSTI)

    Apte, Joshua; Arasteh, Dariush

    2006-06-16T23:59:59.000Z

    We present a simple spreadsheet-based tool for estimating window-related energy consumption in the United States. Using available data on the properties of the installed US window stock, we estimate that windows are responsible for 2.15 quadrillion Btu (Quads) of heating energy consumption and 1.48 Quads of cooling energy consumption annually. We develop estimates of average U-factor and SHGC for current window sales. We estimate that a complete replacement of the installed window stock with these products would result in energy savings of approximately 1.2 quads. We demonstrate that future window technologies offer energy savings potentials of up to 3.9 Quads.

  18. Sealing glasses for titanium and titanium alloys

    DOE Patents [OSTI]

    Brow, R.K.; Watkins, R.D.

    1988-01-21T23:59:59.000Z

    Glass compositions containing CaO, Al/sub 2/O/sub 3/, B/sub 2/O/sub 3/, SrO and BaO of various combinations of mole % are provided. These compositions are capable of forming stable glass-to-metal seals with titanium and titanium alloys, for use in components such as seals for battery headers.

  19. Sealing glasses for titanium and titanium alloys

    DOE Patents [OSTI]

    Brow, Richard K. (Albuquerque, NM); Watkins, Randall D. (Albuquerque, NM)

    1992-01-01T23:59:59.000Z

    Glass compositions containing CaO, Al.sub.2 O.sub.3, B.sub.2 O.sub.3, SrO and BaO of various combinations of mole % are provided. These compositions are capable of forming stable glass-to-metal seals with titanium and titanium alloys, for use in components such as seals for battery headers.

  20. Monitoring and analyzing waste glass compositions

    DOE Patents [OSTI]

    Schumacher, R.F.

    1994-03-01T23:59:59.000Z

    A device and method are described for determining the viscosity of a fluid, preferably molten glass. The apparatus and method use the velocity of rising bubbles, preferably helium bubbles, within the molten glass to determine the viscosity of the molten glass. The bubbles are released from a tube positioned below the surface of the molten glass so that the bubbles pass successively between two sets of electrodes, one above the other, that are continuously monitoring the conductivity of the molten glass. The measured conductivity will change as a bubble passes between the electrodes enabling an accurate determination of when a bubble has passed between the electrodes. The velocity of rising bubbles can be determined from the time interval between a change in conductivity of the first electrode pair and the second, upper electrode pair. The velocity of the rise of the bubbles in the glass melt is used in conjunction with other physical characteristics, obtained by known methods, to determine the viscosity of the glass melt fluid and, hence, glass quality. 2 figures.

  1. Radiation Induced Nanocrystal Formation in Metallic Glasses

    E-Print Network [OSTI]

    Carter, Jesse

    2010-01-14T23:59:59.000Z

    The irradiation of metallic glasses to induce nanocrystallization was studied in two metallic glass compositions, Cu50Zr45Ti5 and Zr55Cu30Al10Ni5. Atomic mobility was described using a model based on localized excess free volume due to displace...

  2. Eyeglass lens made of glass (radiopaque)

    E-Print Network [OSTI]

    Fig. 9-1 Eyeglass lens made of glass (radiopaque) and frame made of metal (radiopaque). #12;Fig. 9-2 Eyeglass lens made of glass (radiopaque) and frame made of plastic (radiolucent). #12;Fig. 9-3 Metal frame of eyeglasses (radiopaque). The eyeglass lens is made of plastic (radiolucent). #12;Fig. 9-4 Cotton roll

  3. Viscous Glass Sealants for SOFC Applications

    SciTech Connect (OSTI)

    Scott Misture

    2012-09-30T23:59:59.000Z

    Two series of silicate glasses that contain gallium as the primary critical component have been identified and optimized for viscous sealing of solid oxide fuel cells operating from 650 to 850°C. Both series of glass sealants crystallize partially upon heat treatment and yield multiphase microstructures that allow viscous flow at temperatures as low as 650°C. A fully amorphous sealant was also developed by isolating, synthesizing and testing a silicate glass of the same composition as the remnant glassy phase in one of the two glass series. Of ~40 glasses tested for longer than 500 hours, a set of 5 glasses has been further tested for up to 1000h in air, wet hydrogen, and against both yttria-stabilized zirconia and aluminized stainless steel. In some cases the testing times reached 2000h. The reactivity testing has provided new insight into the effects of Y, Zr, and Al on bulk and surface crystallization in boro-gallio-silicate glasses, and demonstrated that at least 5 of the newly-developed glasses are viable viscous sealants.

  4. Hydrofluoric acid-resistant composite window and method for its fabrication

    DOE Patents [OSTI]

    Ostenak, C.A.; Mackay, H.A.

    1985-07-18T23:59:59.000Z

    A hydrofluoric acid-resistant composite window and method for its fabrication are disclosed. The composite window comprises a window having first and second sides. The first side is oriented towards an environment containing hydrofluoric acid. An adhesive is applied to the first side. A layer of transparent hydrofluoric acid-resistant material, such as Mylar, is applied to the adhesive and completely covers the first side. The adhesive is then cured.

  5. Glass heat pipe evacuated tube solar collector

    DOE Patents [OSTI]

    McConnell, Robert D. (Lakewood, CO); Vansant, James H. (Tracy, CA)

    1984-01-01T23:59:59.000Z

    A glass heat pipe is adapted for use as a solar energy absorber in an evacuated tube solar collector and for transferring the absorbed solar energy to a working fluid medium or heat sink for storage or practical use. A capillary wick is formed of granular glass particles fused together by heat on the inside surface of the heat pipe with a water glass binder solution to enhance capillary drive distribution of the thermal transfer fluid in the heat pipe throughout the entire inside surface of the evaporator portion of the heat pipe. Selective coatings are used on the heat pipe surface to maximize solar absorption and minimize energy radiation, and the glass wick can alternatively be fabricated with granular particles of black glass or obsidian.

  6. Gaseous Sulfate Solubility in Glass: Experimental Method

    SciTech Connect (OSTI)

    Bliss, Mary

    2013-11-30T23:59:59.000Z

    Sulfate solubility in glass is a key parameter in many commercial glasses and nuclear waste glasses. This report summarizes key publications specific to sulfate solubility experimental methods and the underlying physical chemistry calculations. The published methods and experimental data are used to verify the calculations in this report and are expanded to a range of current technical interest. The calculations and experimental methods described in this report will guide several experiments on sulfate solubility and saturation for the Hanford Waste Treatment Plant Enhanced Waste Glass Models effort. There are several tables of sulfate gas equilibrium values at high temperature to guide experimental gas mixing and to achieve desired SO3 levels. This report also describes the necessary equipment and best practices to perform sulfate saturation experiments for molten glasses. Results and findings will be published when experimental work is finished and this report is validated from the data obtained.

  7. Heat capacity at the glass transition

    E-Print Network [OSTI]

    Kostya Trachenko; Vadim Brazhkin

    2010-07-13T23:59:59.000Z

    A fundamental problem of glass transition is to explain the jump of heat capacity at the glass transition temperature $T_g$ without asserting the existence of a distinct solid glass phase. This problem is also common to other disordered systems, including spin glasses. We propose that if $T_g$ is defined as the temperature at which the liquid stops relaxing at the experimental time scale, the jump of heat capacity at $T_g$ follows as a necessary consequence due to the change of system's elastic, vibrational and thermal properties. In this picture, we discuss time-dependent effects of glass transition, and identify three distinct regimes of relaxation. Our approach explains widely observed logarithmic increase of $T_g$ with the quench rate and the correlation of heat capacity jump with liquid fragility.

  8. A consortium approach to glass furnace modeling.

    SciTech Connect (OSTI)

    Chang, S.-L.; Golchert, B.; Petrick, M.

    1999-04-20T23:59:59.000Z

    Using computational fluid dynamics to model a glass furnace is a difficult task for any one glass company, laboratory, or university to accomplish. The task of building a computational model of the furnace requires knowledge and experience in modeling two dissimilar regimes (the combustion space and the liquid glass bath), along with the skill necessary to couple these two regimes. Also, a detailed set of experimental data is needed in order to evaluate the output of the code to ensure that the code is providing proper results. Since all these diverse skills are not present in any one research institution, a consortium was formed between Argonne National Laboratory, Purdue University, Mississippi State University, and five glass companies in order to marshal these skills into one three-year program. The objective of this program is to develop a fully coupled, validated simulation of a glass melting furnace that may be used by industry to optimize the performance of existing furnaces.

  9. Titanium sealing glasses and seals formed therefrom

    DOE Patents [OSTI]

    Brow, R.K.; McCollister, H.L.; Phifer, C.C.; Day, D.E.

    1997-12-02T23:59:59.000Z

    Alkaline-earth lanthanoborate sealing-glass compositions containing CaO, La{sub 2}O{sub 3}, B{sub 2}O{sub 3}, TiO{sub 2} and Al{sub 2}O{sub 3} in various combinations of mole-% are provided. These sealing-glass compositions are useful for forming hermetic glass-to-metal seals with titanium and titanium alloys that have a high aqueous durability for component or device applications requiring exposure to moisture, water or body fluids. Particular applications of the titanium sealing-glass compositions include forming glass-to-metal seals for lithium batteries and implanted biomedical devices (e.g. batteries, pacemakers, defibrillators, pumps). 2 figs.

  10. Titanium sealing glasses and seals formed therefrom

    DOE Patents [OSTI]

    Brow, Richard K. (Albuquerque, NM); McCollister, Howard L. (Albuquerque, NM); Phifer, Carol C. (Albuquerque, NM); Day, Delbert E. (Rolla, MO)

    1997-01-01T23:59:59.000Z

    Alkaline-earth lanthanoborate sealing-glass compositions containing CaO, La.sub.2 O.sub.3, B.sub.2 O.sub.3, TiO.sub.2 and Al.sub.2 O.sub.3 in various combinations of mole-% are provided. These sealing-glass compositions are useful for forming hermetic glass-to-metal seals with titanium and titanium alloys that have a high aqueous durability for component or device applications requiring exposure to moisture, water or body fluids. Particular applications of the titanium sealing-glass compositions include forming glass-to-metal seals for lithium batteries and implanted biomedical devices (e.g. batteries, pacemakers, defibrillators, pumps).

  11. Bioactive glass coatings for orthopedic metallic implants

    SciTech Connect (OSTI)

    Lopez-Esteban, Sonia; Saiz, Eduardo; Fujino, Sigheru; Oku, Takeo; Suganuma, Katsuaki; Tomsia, Antoni P.

    2003-06-30T23:59:59.000Z

    The objective of this work is to develop bioactive glass coatings for metallic orthopedic implants. A new family of glasses in the SiO2-Na2O-K2O-CaO-MgO-P2O5 system has been synthesized and characterized. The glass properties (thermal expansion, softening and transformation temperatures, density and hardness) are in line with the predictions of established empirical models. The optimized firing conditions to fabricate coatings on Ti-based and Co-Cr alloys have been determined and related to the glass properties and the interfacial reactions. Excellent adhesion to alloys has been achieved through the formation of 100-200 nm thick interfacial layers (Ti5Si3 on Ti-based alloys and CrOx on Co-Cr). Finally, glass coatings, approximately 100 mu m thick, have been fabricated onto commercial Ti alloy-based dental implants.

  12. Purged window apparatus. [On-line spectroscopic analysis of gas flow systems

    DOE Patents [OSTI]

    Ballard, E.O.

    1982-04-05T23:59:59.000Z

    A purged window apparatus is described which utilizes tangentially injected heated purge gases in the vicinity of electromagnetic radiation transmitting windows and a tapered external mounting tube to accelerate these gases to provide a vortex flow on the window surface and a turbulent flow throughout the mounting tube thereby preventing backstreaming of flowing gases under investigation in a chamber to which a plurality of similar purged apparatus is attached with the consequent result that spectroscopic analyses can be undertaken for lengthy periods without the necessity of interrupting the flow for cleaning or replacing the windows due to contamination.

  13. Application issues for large-area electrochromic windows in commercial buildings

    E-Print Network [OSTI]

    Lee, Eleanor S.; DiBartolomeo, D.L.

    2000-01-01T23:59:59.000Z

    Handbook of inorganic electrochromic materials. 1995.R. Sullivan. A Review of Electrochromic Window Performancetime of large-scale electrochromic devices. In Large-Area

  14. T-573: Windows Remote Desktop Client DLL Loading Error Lets Remote Users Execute Arbitrary Code

    Broader source: Energy.gov [DOE]

    A vulnerability was reported in Windows Remote Desktop Client. A remote user can cause arbitrary code to be executed on the target user's system.

  15. Window-Related Energy Consumption in the US Residential and Commercial Building Stock

    E-Print Network [OSTI]

    Apte, Joshua; Arasteh, Dariush

    2008-01-01T23:59:59.000Z

    2001). "Residential Energy Consumption Survey." 2006, fromCommercial Building Energy Consumption Survey." from http://Scale window-related energy consumption to account for new

  16. Smarter Smart Windows | U.S. DOE Office of Science (SC)

    Office of Science (SC) Website

    Smarter Smart Windows Basic Energy Sciences (BES) BES Home About Research Facilities Science Highlights Benefits of BES Funding Opportunities Basic Energy Sciences Advisory...

  17. E-Print Network 3.0 - affordable window insulation Sample Search...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of the UK Forestry Commission Collection: Renewable Energy 5 Renovating Residential HVAC Systems HVAC Systems Summary: windows. Add ceilingwallfloor insulation. 2 Ducts moved...

  18. U-225: Citrix Access Gateway Plug-in for Windows nsepacom ActiveX...

    Broader source: Energy.gov (indexed) [DOE]

    in Citrix Access Gateway Plug-in for Windows can be exploited by malicious people to compromise a user's system. reference LINKS: Citrix Knowledge Center Secunia...

  19. Building Scientific Workflows for Earth System Modelling with Windows Workflow Foundation

    E-Print Network [OSTI]

    Building Scientific Workflows for Earth System Modelling with Windows Workflow Foundation Matthew J developed a framework for the composition, execution and management of integrated Earth system models

  20. Apparatus for preventing particle deposition from process streams on optical access windows

    DOE Patents [OSTI]

    Logan, Ronald G. (Fredericksburg, VA); Grimm, Ulrich (Morgantown, WV)

    1993-01-01T23:59:59.000Z

    An electrostatic precipitator is disposed inside and around the periphery of the window of a viewing port communicating with a housing through which a particle-laden gas stream is being passed. The precipitator includes a pair of electrodes around the periphery of the window, spaced apart and connected to a unidirectional voltage source. Application of high voltage from the source to the electrodes causes air molecules in the gas stream to become ionized, attaching to solid particles and causing them to be deposited on a collector electrode. This prevents the particles from being deposited on the window and keeps the window clean for viewing and making optical measurements.

  1. U< I 7 jjORNLCON-3S) EXPERIMENTAL ANALYSIS OF A WINDOW

    E-Print Network [OSTI]

    Oak Ridge National Laboratory

    UAIR CONDITIONER OAK RIDGE WITH NATIONAL R-22. #12;ORNUCON-389 EXPERIMENTAL ANALYSIS OF A WINDOW AIR CONDITIONER WITH R-22 AND ZEOTROPIC MIXTURE OF R

  2. andesitic glass comparison: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    applications. - Int. J. Solids & Struct. 49 and Motivation Components of Thin Film Solar Modules back sheet or glass encapsulant electrical conductor thin 59 Glass Forming...

  3. ajakirja stained glass: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    applications. - Int. J. Solids & Struct. 49 and Motivation Components of Thin Film Solar Modules back sheet or glass encapsulant electrical conductor thin 122 Glass Forming...

  4. Glass-like thermal conductivity in high efficiency thermoelectric...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Glass-like thermal conductivity in high efficiency thermoelectric materials Glass-like thermal conductivity in high efficiency thermoelectric materials Discusses strategies to...

  5. Photovoltaic Powering And Control System For Electrochromic Windows

    DOE Patents [OSTI]

    Schulz, Stephen C. (Tewksbury, MA); Michalski, Lech A. (Pennington, NJ); Volltrauer, Hermann N. (Englishtown, NJ); Van Dine, John E. (Faribault, MN)

    2000-04-25T23:59:59.000Z

    A sealed insulated glass unit is provided with an electrochromic device for modulating light passing through the unit. The electrochromic device is controlled from outside the unit by a remote control electrically unconnected to the device. Circuitry within the unit may be magnetically controlled from outside. The electrochromic device is powered by a photovoltaic cells. The photovoltaic cells may be positioned so that at least a part of the light incident on the cell passes through the electrochromic device, providing a form of feedback control. A variable resistance placed in parallel with the electrochromic element is used to control the response of the electrochromic element to changes in output of the photovoltaic cell.

  6. Water Window Ptychographic Imaging with Characterized Coherent X-rays

    E-Print Network [OSTI]

    Rose, Max; Dzhigaev, Dmitry; Gorobtsov, Oleg; Senkbeil, Tobias; von Gundlach, Andreas; Gorniak, Thomas; Shabalin, Anatoly; Viefhaus, Jens; Rosenhahn, Axel; Vartanyants, Ivan

    2015-01-01T23:59:59.000Z

    We report on a ptychographical coherent diffractive imaging experiment in the water window with focused soft X-rays at $500~\\mathrm{eV}$. An X-ray beam with high degree of coherence was selected for ptychography at the P04 beamline of the PETRA III synchrotron radiation source. We measured the beam coherence with the newly developed non-redundant array method. A pinhole $2.6~\\mathrm{\\mu m}$ in size selected the coherent part of the beam and was used for ptychographic measurements of a lithographically manufactured test sample and fossil diatom. The achieved resolution was $53~\\mathrm{nm}$ for the test sample and only limited by the size of the detector. The diatom was imaged at a resolution better than $90~\\mathrm{nm}$.

  7. Vacuum chamber with a supersonic-flow aerodynamic window

    DOE Patents [OSTI]

    Hanson, C.L.

    1980-10-14T23:59:59.000Z

    A supersonic flow aerodynamic window is disclosed whereby a steam ejector situated in a primary chamber at vacuum exhausts superheated steam toward an orifice to a region of higher pressure, creating a barrier to the gas in the region of higher pressure which attempts to enter through the orifice. In a mixing chamber outside and in fluid communication with the primary chamber, superheated steam and gas are combined into a mixture which then enters the primary chamber through the orifice. At the point of impact of the ejector/superheated steam and the incoming gas/superheated steam mixture, a barrier is created to the gas attempting to enter the ejector chamber. This barrier, coupled with suitable vacuum pumping means and cooling means, serves to keep the steam ejector and primary chamber at a negative pressure, even though the primary chamber has an orifice to a region of higher pressure.

  8. Vacuum chamber with a supersonic flow aerodynamic window

    DOE Patents [OSTI]

    Hanson, Clark L. (Livermore, CA)

    1982-01-01T23:59:59.000Z

    A supersonic flow aerodynamic window, whereby a steam ejector situated in a primary chamber at vacuum exhausts superheated steam toward an orifice to a region of higher pressure, creating a barrier to the gas in the region of higher pressure which attempts to enter through the orifice. In a mixing chamber outside and in fluid communication with the primary chamber, superheated steam and gas are combined into a mixture which then enters the primary chamber through the orifice. At the point of impact of the ejector/superheated steam and the incoming gas/superheated steam mixture, a barrier is created to the gas attempting to enter the ejector chamber. This barrier, coupled with suitable vacuum pumping means and cooling means, serves to keep the steam ejector and primary chamber at a negative pressure, even though the primary chamber has an orifice to a region of higher pressure.

  9. Chromogenic switchable glazing: Towards the development of the smart window

    SciTech Connect (OSTI)

    Lampert, C.M.

    1995-06-01T23:59:59.000Z

    The science and technology of chromogenic materials for switchable glazings in building applications is discussed. These glazings can be used for dynamic control of solar and visible energy. Currently many researchers and engineers are involved with the development of products in this field. A summary of activities in Japan, Europe, Australia, USA and Canada is made. The activities of the International Energy Agency are included. Both non-electrically activated and electrically activated glazings are discussed. Technologies covered in the first category are photochromics, and thermochromics and thermotropics. A discussion of electrically activated chromogenic glazings includes dispersed liquid crystals, dispersed particles and electrochromics. A selection of device structures and performance characteristics are compared. A discussion of transparent conductors is presented. Technical issues concerning large-area development of smart windows are discussed.

  10. Glass for sealing lithium cells

    DOE Patents [OSTI]

    Leedecke, C.J.

    1981-08-28T23:59:59.000Z

    Glass compositions resistant to corrosion by lithium cell electrolyte and having an expansion coefficient of 45 to 85 x 10/sup -70/C/sup -1/ have been made with SiO/sub 2/, 25 to 55% by weight; B/sub 2/O/sub 3/, 5 to 12%; Al/sub 2/O/sub 3/, 12 to 35%; CaO, 5 to 15%; MgO, 5 to 15%; SrO, 0 to 10%; and La/sub 2/O/sub 3/, 0 to 5%. Preferred compositions within that range contain 3 to 8% SrO and 0.5 to 2.5% La/sub 2/O/sub 3/.

  11. Solid oxide fuel cell having a glass composite seal

    DOE Patents [OSTI]

    De Rose, Anthony J.; Mukerjee, Subhasish; Haltiner, Jr., Karl Jacob

    2013-04-16T23:59:59.000Z

    A solid oxide fuel cell stack having a plurality of cassettes and a glass composite seal disposed between the sealing surfaces of adjacent cassettes, thereby joining the cassettes and providing a hermetic seal therebetween. The glass composite seal includes an alkaline earth aluminosilicate (AEAS) glass disposed about a viscous glass such that the AEAS glass retains the viscous glass in a predetermined position between the first and second sealing surfaces. The AEAS glass provides geometric stability to the glass composite seal to maintain the proper distance between the adjacent cassettes while the viscous glass provides for a compliant and self-healing seal. The glass composite seal may include fibers, powders, and/or beads of zirconium oxide, aluminum oxide, yttria-stabilized zirconia (YSZ), or mixtures thereof, to enhance the desirable properties of the glass composite seal.

  12. The energy-savings potential of electrochromic windows in the UScommercial buildings sector

    SciTech Connect (OSTI)

    Lee, Eleanor; Yazdanian, Mehry; Selkowitz, Stephen

    2004-04-30T23:59:59.000Z

    Switchable electrochromic (EC) windows have been projected to significantly reduce the energy use of buildings nationwide. This study quantifies the potential impact of electrochromic windows on US primary energy use in the commercial building sector and also provides a broader database of energy use and peak demand savings for perimeter zones than that given in previous LBNL simulation studies. The DOE-2.1E building simulation program was used to predict the annual energy use of a three-story prototypical commercial office building located in five US climates and 16 California climate zones. The energy performance of an electrochromic window controlled to maintain daylight illuminance at a prescribed setpoint level is compared to conventional and the best available commercial windows as well as windows defined by the ASHRAE 90.1-1999 and California Title 24-2005 Prescriptive Standards. Perimeter zone energy use and peak demand savings data by orientation, window size, and climate are given for windows with interior shading, attached shading, and horizon obstructions (to simulate an urban environment). Perimeter zone primary energy use is reduced by 10-20% in east, south, and west zones in most climates if the commercial building has a large window-to-wall area ratio of 0.60 compared to a spectrally selective low-e window with daylighting controls and no interior or exterior shading. Peak demand for the same condition is reduced by 20-30%. The emerging electrochromic window with daylighting controls is projected to save approximately 91.5-97.3 10{sup 12} Btu in the year 2030 compared to a spectrally selective low-E window with manually-controlled interior shades and no daylighting controls if it reaches a 40% market penetration level in that year.

  13. HGMS: Glasses and Nanocomposites for Hydrogen Storage.

    SciTech Connect (OSTI)

    Lipinska, Kris [PI] [PI; Hemmers, Oliver

    2013-02-17T23:59:59.000Z

    The primary goal of this project is to fabricate and investigate different glass systems and glass-derived nanocrystalline composite materials. These glass-based, two-phased materials will contain nanocrystals that can attract hydrogen and be of potential interest as hydrogen storage media. The glass materials with intrinsic void spaces that are able to precipitate functional nanocrystals capable to attract hydrogen are of particular interest. Proposed previously, but never practically implemented, one of promising concepts for storing hydrogen are micro-containers built of glass and shaped into hollow microspheres. The project expanded this concept to the exploration of glass-derived nanocrystalline composites as potential hydrogen storage media. It is known that the most desirable materials for hydrogen storage do not interact chemically with hydrogen and possess a high surface area to host substantial amounts of hydrogen. Glasses are built of disordered networks with ample void spaces that make them permeable to hydrogen even at room temperature. Glass-derived nanocrystalline composites (two-phased materials), combination of glasses (networks with ample voids) and functional nanocrystals (capable to attract hydrogen), appear to be promising candidates for hydrogen storage media. Key advantages of glass materials include simplicity of preparation, flexibility of composition, chemical durability, non-toxicity and mechanical strength, as well as low production costs and environmental friendliness. This project encompasses a fundamental research into physics and chemistry of glasses and nanocrystalline composite materials, derived from glass. Studies are aimed to answer questions essential for considering glass-based materials and composites as potential hydrogen storage media. Of particular interest are two-phased materials that combine glasses with intrinsic voids spaces for physisorption of hydrogen and nanocrystals capable of chemisorption. This project does not directly address any hydrogen storage technical barriers or targets in terms of numbers. Specifically, hydrogen sorption and desorption tests or kinetics measurements were not part of the project scope. However, the insights gained from these studies could help to answer fundamental questions necessary for considering glass-based materials as hydrogen storage media and could be applied indirectly towards the DOE hydrogen storage technical targets such as system weight and volume, system cost and energy density. Such questions are: Can specific macro-crystals, proven to attract hydrogen when in a macroscopic form (bulk), be nucleated in glass matrices as nanocrystals to create two-phased materials? What are suitable compositions that enable to synthetize glass-based, two-phase materials with nanocrystals that can attract hydrogen via surface or bulk interactions? What are the limits of controlling the microstructure of these materials, especially limits for nanocrystals density and size? Finally, from a technological point of view, the fabrication of glass-derived nanocomposites that we explore is a very simple, fast and inexpensive process that does not require costly or specialized equipment which is an important factor for practical applications.

  14. Energy implications of glass-container recycling

    SciTech Connect (OSTI)

    Gaines, L.L.; Mintz, M.M. [Argonne National Lab., IL (United States)] [Argonne National Lab., IL (United States)

    1994-03-01T23:59:59.000Z

    This report addresses the question of whether glass-container recycling actually saves energy. Glass-container production in 1991 was 10{sup 7} tons, with cullet making up about 30% of the input to manufacture. Two-thirds of the cullet is postconsumer waste; the remainder is in-house scrap (rejects). Most of the glass recycled is made into new containers. Total primary energy consumption includes direct process-energy use by the industry (adjusted to account for the efficiency of fuel production) plus fuel and raw-material transportation and production energies; the grand total for 1991 is estimated to be about 168 {times} 10{sup 12} Btu. The total primary energy use decreases as the percent of glass recycled rises, but the maximum energy saved is only about 13%. If distance to the landfill is kept fixed and that to the recovery facility multiplied by about eight, to 100 mi, a break-even point is reached, and recycling saves no energy. Previous work has shown that to save energy when using glass bottles, reuse is the clear choice. Recycling of glass does not save much energy or valuable raw material and does not reduce air or water pollution significantly. The most important impacts are the small reduction of waste sent to the landfill and increased production rates at glass plants.

  15. Dynamics and rheology of active glasses

    E-Print Network [OSTI]

    T. F. F. Farage; J. M. Brader

    2014-03-07T23:59:59.000Z

    Within the framework of mode-coupling theory, we present a simple model for describing dense assemblies of active (self-propelled) spherical colloidal particles. For isotropic suspensions, we demonstrate that the glass transition is shifted to higher volume fraction by the addition of activity, in agreement with recent Brownian dynamics simulations. Activity-induced changes in the static structure factor of the fluid are predicted. The mechanical response of an active glass to applied strain is shown to be softer than the corresponding passive glass; both the nonergodicity parameter and the yield stress reduce with increasing activity.

  16. TTUS FP&C Design & Building Standards Division 8 Doors & Windows

    E-Print Network [OSTI]

    Gelfond, Michael

    8 ­ Doors & Windows General Energy conservation and sustainable design must be given thorough with State Energy Code and ASHRAE 90.1. Energy Efficient Exterior Openings shall comply with minimumTTUS FP&C Design & Building Standards Division 8 ­ Doors & Windows Page 1 of 11 Division

  17. Reliability Assessment of Mass-Market Software: Insights from Windows Vista

    E-Print Network [OSTI]

    Khambatt, Mujtaba

    Reliability Assessment of Mass-Market Software: Insights from Windows Vista® Paul Luo Li, Mingtian Ni, Song Xue, Joseph P. Mullally, Mario Garzia, Mujtaba Khambatti Microsoft Windows Reliability Team One Microsoft Way Redmond, WA USA Paul.Li@Microsoft.com Abstract Assessing the reliability of mass

  18. Design Windows for a He Cooled Fusion Reactor* Dai-Kai Sze and Ahmed Hassanein

    E-Print Network [OSTI]

    Harilal, S. S.

    Design Windows for a He Cooled Fusion Reactor* Dai-Kai Sze and Ahmed Hassanein Argonne National Laboratory 9700 South Cass Avenue, Argonne, IL 60439 EQUATIONDERIVATION ABSTRACT A design window concept is developed for a He-cooled fusion reactor blanket and divertor design. This concept allows study

  19. Author's personal copy The time dependent vehicle routing problem with time windows

    E-Print Network [OSTI]

    Bertini, Robert L.

    : (a) formulate a time dependent vehicle routing problem with a general cost function and time windowAuthor's personal copy The time dependent vehicle routing problem with time windows: Benchmark College of Engineering and Computer Science, PO Box 0751, Portland State University, Portland, OR 97207

  20. Plasmonic Metamaterials and Nanocomposites with the Narrow Transparency Window Effect in Broad Extinction Spectra

    E-Print Network [OSTI]

    Demir, Hilmi Volkan

    Plasmonic Metamaterials and Nanocomposites with the Narrow Transparency Window Effect in Broad from 400 nm to 5 m but exhibit a narrow transparency window centered at a given wavelength. The main be designed as a solution, nanocomposite film or metastructure. The principle of the formation

  1. Daylighting control performance of a thin-film ceramic electrochromic window: field study results

    E-Print Network [OSTI]

    1 Daylighting control performance of a thin-film ceramic electrochromic window: field study results of this emerging technology. Keywords: Building energy-efficiency; Electrochromic windows; Daylighting; Control switched across their dynamic range and could be fully integrated into a complete daylight, glare

  2. Empirical assessment of a prismatic daylight-redirecting window film in a full-scale office

    E-Print Network [OSTI]

    LBNL-6496E Empirical assessment of a prismatic daylight- redirecting window film in a full in Leukos, the journal of the IESNA. Empirical assessment of a prismatic daylight- redirecting window film Laboratory, Mailstop 90-3111, 1 Cyclotron Road, Berkeley, CA 94720 USA Abstract Daylight redirecting systems

  3. Three-tank hoist scheduling problem with unbounded or zero-width processing windows

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Three-tank hoist scheduling problem with unbounded or zero-width processing windows Fabien Mangione, the products are transferred in successive tanks by a hoist. Moreover, each processing time is nested between of identical parts in a balanced three-tank line. We prove that for zero-width or unbounded processing windows

  4. SLUDGE BATCH 7B GLASS VARIABILITY STUDY

    SciTech Connect (OSTI)

    Johnson, F.; Edwards, T.

    2011-10-25T23:59:59.000Z

    The Defense Waste Processing Facility (DWPF) is preparing to initiate processing Sludge Batch 7b (SB7b). In support of the upcoming processing, the Savannah River National Laboratory (SRNL) provided a recommendation to utilize Frits 418 with a 6% Na{sub 2}O addition (26 wt% Na{sub 2}O in sludge) and 702 with a 4% Na{sub 2}O addition (24 wt% Na{sub 2}O in sludge) to process SB7b. This recommendation was based on assessments of the compositional projections for SB7b available at the time from the Savannah River Remediation (SRR). To support qualification of SB7b, SRNL executed a variability study to assess the applicability of the current durability models for SB7b. The durability models were assessed over the expected composition range of SB7b, including potential caustic additions, combined with Frits 702 and 418 over a 32-40% waste loading (WL) range. Thirty four glasses were selected based on Frits 418 and 702 coupled with the sludge projections with an additional 4-6% Na{sub 2}O to reflect the potential caustic addition. Six of these glasses, based on average nominal sludge compositions including the appropriate caustic addition, were developed for both Frit 418 and Frit 702 at 32, 36 and 40% WL to provide coverage in the center of the anticipated SB7b glass region. All glasses were fabricated and characterized using chemical composition analysis, X-ray diffraction (XRD) and the Product Consistency Test (PCT). To comply with the DWPF Glass Product Control Program, a total of thirty four glasses were fabricated to assess the applicability of the current DWPF PCCS durability models. Based on the measured PCT response, all of the glasses were acceptable with respect to the Environmental Assessment (EA) benchmark glass regardless of thermal history. The NL[B] values of the SB7b variability study glasses were less than 1.99 g/L as compared to 16.695 g/L for EA. A small number of the D-optimally selected 'outer layer' extreme vertices (EV) glasses were not predictable using the current Product Composition Control System (PCCS) models for durability, but were acceptable compared to the EA glass when tested. These glasses fell outside of the lower 95% confidence band, which demonstrates conservatism in the model. A few of the glasses fell outside of the upper 95% confidence band; however, these particular glasses have normalized release values that were much lower than the values of EA and should be of no practical concern. Per the requirements of the DWPF Glass Product Control Program, the PCCS durability models have been shown to be applicable to the SB7b sludge system with a range of Na{sub 2}O concentrations blended with Frits 418 or 702. PCT results from the glasses fabricated as part of the variability study were shown to be predictable by the current DWPF PCCS models and/or acceptable with respect to the EA benchmark glass regardless of thermal history or compositional view.

  5. Method of fabricating a microelectronic device package with an integral window

    DOE Patents [OSTI]

    Peterson, Kenneth A. (Albuquerque, NM); Watson, Robert D. (Tijeras, NM)

    2003-01-01T23:59:59.000Z

    A method of fabricating a microelectronic device package with an integral window for providing optical access through an aperture in the package. The package is made of a multilayered insulating material, e.g., a low-temperature cofired ceramic (LTCC) or high-temperature cofired ceramic (HTCC). The window is inserted in-between personalized layers of ceramic green tape during stackup and registration. Then, during baking and firing, the integral window is simultaneously bonded to the sintered ceramic layers of the densified package. Next, the microelectronic device is flip-chip bonded to cofired thick-film metallized traces on the package, where the light-sensitive side is optically accessible through the window. Finally, a cover lid is attached to the opposite side of the package. The result is a compact, low-profile package, flip-chip bonded, hermetically-sealed package having an integral window.

  6. Mechanical Research and Development of monocrystalline silicon neutron beam window for CSNS

    E-Print Network [OSTI]

    Zhou Liang; Qu Hua-Min

    2014-11-24T23:59:59.000Z

    The monocrystalline silicon neutron beam window is one of the key components of neutron spectrometers and thin circular plate.Monocrystalline silicon is a brittle material and its strength is not constant but is consistent with the Weibull distribution. The window is designed not simply through the average strength, but according to the survival rate. Bending deformation is the main form of the window, so dangerous parts of the neutron beam window is stress-linearized to the combination of membrane stress and bending stress. According to the Weibull distribution of bending strength of monocrystalline silicon based on a large number of experimental data, finally the optimized neutron beam window is 1.5mm thick. Its survival rate is 0.9994 and its transmittance is 0.98447; it meets both physical requirements and the mechanical strength.

  7. Performance Analysis of Contention Window Cheating Misbehaviors in Mobile Ad Hoc Networks

    E-Print Network [OSTI]

    Kalaiarasi, R; Pari, S Neelavathy; Sridharan, D

    2010-01-01T23:59:59.000Z

    Mobile Ad Hoc Network (MANET) is a collection of nodes that can be rapidly deployed as a multi-hop network without the aid of any centralized administration. Misbehavior is challenged by bandwidth and energy efficient medium access control and fair share of throughput. Node misbehavior plays an important role in MANET. In this survey, few of the contention window misbehavior is reviewed and compared. The contention window cheating either minimizes the active communication of the network or reduces bandwidth utilization of a particular node. The classification presented is in no case unique but summarizes the chief characteristics of many published proposals for contention window cheating. After getting insight into the different contention window misbehavior, few of the enhancements that can be done to improve the existing contention window are suggested. The purpose of this paper is to facilitate the research efforts in combining the existing solutions to offer more efficient methods to reduce contention win...

  8. Glass/polymer composites and methods of making

    DOE Patents [OSTI]

    Samuels, W. D. (Richland, WA); Exarhos, Gregory J. (Richland, WA)

    1995-01-01T23:59:59.000Z

    The present invention relates to new glass/polymer composites and methods for making them. More specifically, the invention is glass/polymer composites having phases that are at the molecular level and thereby practicably indistinguishable. The invention further discloses making molecular phase glass/polymer composites by mixing a glass and a polymer in a compatible solvent.

  9. Glass bead micromodel study of solute transport

    E-Print Network [OSTI]

    Fedirchuk, Paula Diane

    1995-01-01T23:59:59.000Z

    This study presents the quantification of glass bead micromodel experiments through a combination of computational modeling and experimental analysis. The computational model simulates two-dimensional solute flow through porous media using a finite...

  10. Neutron Brillouin scattering in a metallic glass

    SciTech Connect (OSTI)

    Suck, J.B. (Kernforschungszentrum Karlsruhe GmbH (Germany). Inst. fuer Nukleare Festkoerperphysik); Egelstaff, P.A. (Guelph Univ., ON (Canada). Dept. of Physics); Robinson, R.A.; Sivia, D.S. (Los Alamos National Lab., NM (United States)); Taylor, A.D. (Rutherford Appleton Lab., Chilton (United Kingdom))

    1991-01-01T23:59:59.000Z

    The dispersion of collective modes in a metallic glass (Mg{sub 70}Zn{sub 30}) measured earlier at the thermal neutron time-of-flight spectrometer IN4 of the HFR of the ILL could be extended towards lower momentum transfers down to the first pseudo-Brillouin zone for the first time. This extension to momentum transfer not accessible up to now was possible using the highly resolving time-of-flight spectrometer HET of the new spallation source ISIS. In the region of overlap the two parts of the dispersion determined with different samples of the same metallic glass on different instruments agree very well. Also the earlier discrepancies with the dispersion determined for this metallic glass from a computer simulation could be nearly completely eliminated due to a more recent and more complete investigations of this glass.

  11. Preparation of fullerene/glass composites

    DOE Patents [OSTI]

    Mattes, B.R.; McBranch, D.W.; Robinson, J.M.; Koskelo, A.C.; Love, S.P.

    1995-05-30T23:59:59.000Z

    Synthesis of fullerene/glass composites is described. A direct method for preparing solid solutions of C{sub 60} in silicon dioxide (SiO{sub 2}) glass matrices by means of sol-gel chemistry is described. In order to produce highly concentrated fullerene-sol-gel-composites it is necessary to increase the solubility of these ``guests`` in a delivery solvent which is compatible with the starter sol (receiving solvent). Sonication results in aggregate disruption by treatment with high frequency sound waves, thereby accelerating the rate of hydrolysis of the alkoxide precursor, and the solution process for the C{sub 60}. Depending upon the preparative procedure, C{sub 60} dispersed within the glass matrix as microcrystalline domains, or dispersed as true molecular solutions of C{sub 60} in a solid glass matrix, is generated by the present method.

  12. Measurement of DWPF glass viscosity - Final Report

    SciTech Connect (OSTI)

    Harbour, J.R.

    2000-02-17T23:59:59.000Z

    This report details the results of a scoping study funded by the Defense Waste Processing Facility (DWPF) for the measurement of melt viscosities for simulated glasses representative of Macrobatch 2 (Tank 42/51 feed).

  13. Energy Assessment Protocol for Glass Furnaces

    E-Print Network [OSTI]

    Plodinec, M. J.; Kauffman, B. M.; Norton, O. P.; Richards, C.; Connors, J.; Wishnick, D.

    2005-01-01T23:59:59.000Z

    The Department of Energy funded development of a methodology that could be used by glass producers to increase furnace efficiency, and that could serve as a model for other energy-intensive industries. Accordingly, a team comprising PPG Industries...

  14. Tiny Glass Bubbles With Big Potential

    Broader source: Energy.gov [DOE]

    If these glass microspheres' walls could talk…They would explain how their tiny pores allow the potential for handling, storing and transporting a variety of materials, including drugs that have...

  15. Preparation of fullerene/glass composites

    DOE Patents [OSTI]

    Mattes, Benjamin R. (Santa Fe, NM); McBranch, Duncan W. (Santa Fe, NM); Robinson, Jeanne M. (Los Alamos, NM); Koskelo, Aaron C. (Los Alamos, NM); Love, Steven P. (Los Alamos, NM)

    1995-01-01T23:59:59.000Z

    Synthesis of fullerene/glass composites. A direct method for preparing solid solutions of C.sub.60 in silicon dioxide (SiO.sub.2) glass matrices by means of sol-gel chemistry is described. In order to produce highly concentrated fullerene-sol-gel-composites it is necessary to increase the solubility of these "guests" in a delivery solvent which is compatible with the starter sol (receiving solvent). Sonication results in aggregate disruption by treatment with high frequency sound waves, thereby accelerating the rate of hydrolysis of the alkoxide precursor, and the solution process for the C.sub.60. Depending upon the preparative procedure, C.sub.60 dispersed within the glass matrix as microcrystalline domains, or dispersed as true molecular solutions of C.sub.60 in a solid glass matrix, is generated by the present method.

  16. High expansion, lithium corrosion resistant sealing glasses

    DOE Patents [OSTI]

    Brow, Richard K. (Albuquerque, NM); Watkins, Randall D. (Albuquerque, NM)

    1991-01-01T23:59:59.000Z

    Glass compositions containing CaO, Al.sub.2 O.sub.3, B.sub.2 O.sub.3, SrO and BaO in various combinations of mole % are provided. These compositions are capable of forming stable glass-to-metal seals with pin materials of 446 Stainless Steel and Alloy-52 rather than molybdenum, for use in harsh chemical environments, specifically in lithium batteries.

  17. High expansion, lithium corrosion resistant sealing glasses

    DOE Patents [OSTI]

    Brow, R.K.; Watkins, R.D.

    1991-06-04T23:59:59.000Z

    Glass compositions containing CaO, Al[sub 2]O[sub 3], B[sub 2]O[sub 3], SrO and BaO in various combinations of mole % are provided. These compositions are capable of forming stable glass-to-metal seals with pin materials of 446 Stainless Steel and Alloy-52 rather than molybdenum, for use in harsh chemical environments, specifically in lithium batteries.

  18. MECS 2006 - Glass | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion | Department of Energy Low-Temperature CombustionGlass MECS 2006 - Glass Manufacturing

  19. ICG 2000 Amsterdam Glass in the new Millennium Absorption Spectra of Iron and Water in Silicate Glasses

    E-Print Network [OSTI]

    Glebov, Leon

    ICG 2000 Amsterdam ­ Glass in the new Millennium Absorption Spectra of Iron and Water in Silicate of the absorption spectrum of silicate glasses and determination of absolute concentrations of ferric, ferrous of silicate glass. 2. Experimental The same glass samples were used in this work as were described in [3, 4

  20. Sealed glass coating of high temperature ceramic superconductors

    DOE Patents [OSTI]

    Wu, Weite (Tainan, TW); Chu, Cha Y. (Garnerville, NY); Goretta, Kenneth C. (Downers Grove, IL); Routbort, Jules L. (Darien, IL)

    1995-01-01T23:59:59.000Z

    A method and article of manufacture of a lead oxide based glass coating on a high temperature superconductor. The method includes preparing a dispersion of glass powders in a solution, applying the dispersion to the superconductor, drying the dispersion before applying another coating and heating the glass powder dispersion at temperatures below oxygen diffusion onset and above the glass melting point to form a continuous glass coating on the superconductor to establish compressive stresses which enhance the fracture strength of the superconductor.

  1. Hysteretic Optimization For Spin Glasses

    E-Print Network [OSTI]

    B. Goncalves; S. Boettcher

    2007-12-10T23:59:59.000Z

    The recently proposed Hysteretic Optimization (HO) procedure is applied to the 1D Ising spin chain with long range interactions. To study its effectiveness, the quality of ground state energies found as a function of the distance dependence exponent, $\\sigma$, is assessed. It is found that the transition from an infinite-range to a long-range interaction at $\\sigma=0.5$ is accompanied by a sharp decrease in the performance . The transition is signaled by a change in the scaling behavior of the average avalanche size observed during the hysteresis process. This indicates that HO requires the system to be infinite-range, with a high degree of interconnectivity between variables leading to large avalanches, in order to function properly. An analysis of the way auto-correlations evolve during the optimization procedure confirm that the search of phase space is less efficient, with the system becoming effectively stuck in suboptimal configurations much earlier. These observations explain the poor performance that HO obtained for the Edwards-Anderson spin glass on finite-dimensional lattices, and suggest that its usefulness might be limited in many combinatorial optimization problems.

  2. Glass produced by underground nuclear explosions. [Rainier

    SciTech Connect (OSTI)

    Schwartz, L.; Piwinskii, A.; Ryerson, F.; Tewes, H.; Beiriger, W.

    1983-01-01T23:59:59.000Z

    Detonation of an underground nuclear explosive produces a strong shock wave which propagates spherically outward, vaporizing the explosive and nearby rock and melting, the surrounding rock. The vaporized material expands adiabatically, forming a cavity. As the energy is dissipated during the cavity formation process, the explosive and rock debris condense and mix with the melted rock. The melt flows to the bottom of the cavity where it is quenched by fractured rock fragments falling from above as the cavity collapses. Measurements indicate that about 740 tonnes of rock and/or soil are melted for every kiloton (10/sup 12/ calories) of explosive energy, or about 25% of the explosive energy goes to melting rock. The resulting glass composition reflects the composition of the unaltered rock with explosive debris. The appearance ranges from white pumice to dense, dark lava. The bulk composition and color vary with the amount of explosive iron incorporated into the glass. The refractory explosion products are mixed with the solidified melt, although the degree of mixing is variable. Electron microprobe studies of glasses produced by Rainier in welded tuff have produced the following results: glasses are dehydrated relative to the host media, glasses are extremely heterogeneous on a 20 ..mu..m scale, a ubiquitous feature is the presence of dark marble-cake regions in the glass, which were locally enriched in iron and may be related to the debris, optically amorphous regions provide evidence of shock melting, only limited major element redistribution and homogenization occur within the cavity.

  3. State-of-the-Art Highly Insulating Window Frames - Research and Market Review

    SciTech Connect (OSTI)

    Gustavsen, Arild; Jelle, Bjorn Petter; Arasteh, Dariush; Kohler, Christian

    2007-01-01T23:59:59.000Z

    This document reports the findings of a market and research review related to state-of-the-art highly insulating window frames. The market review focuses on window frames that satisfy the Passivhaus requirements (window U-value less or equal to 0.8 W/m{sup 2}K ), while other examples are also given in order to show the variety of materials and solutions that may be used for constructing window frames with a low thermal transmittance (U-value). The market search shows that several combinations of materials are used in order to obtain window frames with a low U-value. The most common insulating material seems to be Polyurethane (PUR), which is used together with most of the common structural materials such as wood, aluminum, and PVC. The frame research review also shows examples of window frames developed in order to increase the energy efficiency of the frames and the glazings which the frames are to be used together with. The authors find that two main tracks are used in searching for better solutions. The first one is to minimize the heat losses through the frame itself. The result is that conductive materials are replaced by highly thermal insulating materials and air cavities. The other option is to reduce the window frame area to a minimum, which is done by focusing on the net energy gain by the entire window (frame, spacer and glazing). Literature shows that a window with a higher U-value may give a net energy gain to a building that is higher than a window with a smaller U-value. The net energy gain is calculated by subtracting the transmission losses through the window from the solar energy passing through the windows. The net energy gain depends on frame versus glazing area, solar factor, solar irradiance, calculation period and U-value. The frame research review also discusses heat transfer modeling issues related to window frames. Thermal performance increasing measures, surface modeling, and frame cavity modeling are among the topics discussed. The review shows that the current knowledge gives the basis for improving the calculation procedures in the calculation standards. At the same time it is room for improvement within some areas, e.g. to fully understand the natural convection effects inside irregular vertical frame cavities (jambs) and ventilated frame cavities.

  4. To be submitted to Solar Energy. Daylight performance of a microstructured prismatic window film in deep open

    E-Print Network [OSTI]

    To be submitted to Solar Energy. Daylight performance of a microstructured prismatic window film Systems Department, Environmental Energy Technologies Division, Lawrence Berkeley National Laboratory with vertical windows have the potential to offset lighting energy use in deep perimeter zones

  5. Two-Dimensional Computational Fluid Dynamics and Conduction Simulations of Heat Transfer in Horizontal Window Frames with Internal Cavities

    E-Print Network [OSTI]

    Gustavsen, Arlid

    2008-01-01T23:59:59.000Z

    window frames; To the left, a PVC window frame (S1) and toaluminum frame, S3 (left) and PVC frame, S4 (right) Figuremade of polyvinyl chloride (PVC) and two of aluminum. For

  6. Natural glass analogues to alteration of nuclear waste glass: A review and recommendations for further study

    SciTech Connect (OSTI)

    McKenzie, W.F.

    1990-01-01T23:59:59.000Z

    The purpose of this report is to review previous work on the weathering of natural glasses; and to make recommendations for further work with respect to studying the alteration of natural glasses as it relates quantifying rates of dissolution. the first task was greatly simplified by the published papers of Jercinovic and Ewing (1987) and Byers, Jercinovic, and Ewing (1987). The second task is obviously the more difficult of the two and the author makes no claim of completeness in this regard. Glasses weather in the natural environment by reacting with aqueous solutions producing a rind of secondary solid phases. It had been proposed by some workers that the thickness of this rind is a function of the age of the glass and thus could be used to estimate glass dissolution rates. However, Jercinovic and Ewing (1987) point out that in general the rind thickness does not correlate with the age of the glass owing to the differences in time of contact with the solution compared to the actual age of the sample. It should be noted that the rate of glass dissolution is also a function of the composition of both the glass and the solution, and the temperature. Quantification of the effects of these parameters (as well as time of contact with the aqueous phase and flow rates) would thus permit a prediction of the consequences of glass-fluid interactions under varying environmental conditions. Defense high- level nuclear waste (DHLW), consisting primarily of liquid and sludge, will be encapsulated by and dispersed in a borosilicate glass before permanent storage in a HLW repository. This glass containing the DHLW serves to dilute the radionuclides and to retard their dispersion into the environment. 318 refs.

  7. Text-Alternative Version of Building America Webinar: Low-e Storms: The Next "Big Thing" in Window Retrofits

    Broader source: Energy.gov [DOE]

    Low-e Storms:  The Next “Big Thing” in Window RetrofitsOfficial Webinar Transcript (September 9, 2014)

  8. Engineering Glass Passivation Layers -Model Results

    SciTech Connect (OSTI)

    Skorski, Daniel C.; Ryan, Joseph V.; Strachan, Denis M.; Lepry, William C.

    2011-08-08T23:59:59.000Z

    The immobilization of radioactive waste into glass waste forms is a baseline process of nuclear waste management not only in the United States, but worldwide. The rate of radionuclide release from these glasses is a critical measure of the quality of the waste form. Over long-term tests and using extrapolations of ancient analogues, it has been shown that well designed glasses exhibit a dissolution rate that quickly decreases to a slow residual rate for the lifetime of the glass. The mechanistic cause of this decreased corrosion rate is a subject of debate, with one of the major theories suggesting that the decrease is caused by the formation of corrosion products in such a manner as to present a diffusion barrier on the surface of the glass. Although there is much evidence of this type of mechanism, there has been no attempt to engineer the effect to maximize the passivating qualities of the corrosion products. This study represents the first attempt to engineer the creation of passivating phases on the surface of glasses. Our approach utilizes interactions between the dissolving glass and elements from the disposal environment to create impermeable capping layers. By drawing from other corrosion studies in areas where passivation layers have been successfully engineered to protect the bulk material, we present here a report on mineral phases that are likely have a morphological tendency to encrust the surface of the glass. Our modeling has focused on using the AFCI glass system in a carbonate, sulfate, and phosphate rich environment. We evaluate the minerals predicted to form to determine the likelihood of the formation of a protective layer on the surface of the glass. We have also modeled individual ions in solutions vs. pH and the addition of aluminum and silicon. These results allow us to understand the pH and ion concentration dependence of mineral formation. We have determined that iron minerals are likely to form a complete incrustation layer and we plan to look more closely at Vivianite [Fe3(PO4)2-8(H2O)] and Siderite [FeCO3] in the next stage of the project.

  9. Design of an Aluminum Proton Beam Window for the Spallation Neutron Source

    SciTech Connect (OSTI)

    Janney, Jim G [ORNL; McClintock, David A [ORNL

    2012-01-01T23:59:59.000Z

    An aluminum proton beam window design is being considered at the Spallation Neutron Source primarily to increase the lifetime of the window, with secondary advantages of higher beam transport efficiency and lower activation. The window separates the core vessel, the location of the mercury target, from the vacuum of the accelerator, while withstanding the pass through of a proton beam of up to 2 MW with 1.0 GeV proton energy. The current aluminum alloy being investigated for the window material is 6061-T651 due to its combination of high strength, high thermal conductivity, and good resistance to aqueous corrosion, as well as demonstrated dependability in previous high-radiation environments. The window design will feature a thin plate with closely spaced cross drilled cooling holes. An analytical approach was used to optimize the dimensions of the window before finite element analysis was used to simulate temperature profiles and stress fields resulting from thermal and static pressure loading. The resulting maximum temperature of 60 C and Von Mises stress of 71 MPa are very low compared to allowables for Al 6061-T651. A significant challenge in designing an aluminum proton beam window for SNS is integrating the window with the current 316L SS shield blocks. Explosion bonding was chosen as a joining technique because of the large bonding area required. A test program has commenced to prove explosion bonding can produce a robust vacuum joint. Pending successful explosion bond testing, the aluminum proton beam window design will be proven acceptable for service in the Spallation Neutron Source.

  10. Mechanical property evaluation of porous 13-93 Bioactive Glass and GL1550 Borate Glass 3D scaffolds D. Li, A. Scully, and T. M. G. Chu

    E-Print Network [OSTI]

    Zhou, Yaoqi

    Mechanical property evaluation of porous 13-93 Bioactive Glass and GL1550 Borate Glass 3D scaffolds-glass (A) and GL1550 borate bioactive-glass (B) powders, at different sintering temperatures, and with (failure, Pb) of scaffolds made from 13-93 bioactive- glass and GL1550 bioactive-glass powders are compared

  11. Submitted to Energy and Buildings February 23, 2005 and accepted for publication March 1, 2006. Subject responses to electrochromic windows

    E-Print Network [OSTI]

    . LBNL-57125 Subject responses to electrochromic windows R.D. Clear* , V. Inkarojrit, E.S. Lee Building in a private office with switchable electrochromic windows, manually- operated Venetian blinds, and dimmable fluorescent lights. The electrochromic window had a visible transmittance range of approximately 3

  12. An Insulating Glass Knowledge Base

    SciTech Connect (OSTI)

    Michael L. Doll; Gerald Hendrickson; Gerard Lagos; Russell Pylkki; Chris Christensen; Charlie Cureija

    2005-08-01T23:59:59.000Z

    This report will discuss issues relevant to Insulating Glass (IG) durability performance by presenting the observations and developed conclusions in a logical sequential format. This concluding effort discusses Phase II activities and focuses on beginning to quantifying IG durability issues while continuing the approach presented in the Phase I activities (Appendix 1) which discuss a qualitative assessment of durability issues. Phase II developed a focus around two specific IG design classes previously presented in Phase I of this project. The typical box spacer and thermoplastic spacer design including their Failure Modes and Effect Analysis (FMEA) and Fault Tree diagrams were chosen to address two currently used IG design options with varying components and failure modes. The system failures occur due to failures of components or their interfaces. Efforts to begin quantifying the durability issues focused on the development and delivery of an included computer based IG durability simulation program. The focus/effort to deliver the foundation for a comprehensive IG durability simulation tool is necessary to address advancements needed to meet current and future building envelope energy performance goals. This need is based upon the current lack of IG field failure data and the lengthy field observation time necessary for this data collection. Ultimately, the simulation program is intended to be used by designers throughout the current and future industry supply chain. Its use is intended to advance IG durability as expectations grow around energy conservation and with the growth of embedded technologies as required to meet energy needs. In addition the tool has the immediate benefit of providing insight for research and improvement prioritization. Included in the simulation model presentation are elements and/or methods to address IG materials, design, process, quality, induced stress (environmental and other factors), validation, etc. In addition, acquired data is presented in support of project and model assumptions. Finally, current and suggested testing protocol and procedure for future model validation and IG physical testing are discussed.

  13. Glass science tutorial: Lecture No. 4, commercial glass melting and associated air emission issues

    SciTech Connect (OSTI)

    Kruger, A.A.

    1995-01-01T23:59:59.000Z

    This document serves as a manual for a workshop on commercial glass melting and associated air emission issues. Areas covered include: An overview of the glass industry; Furnace design and construction practices; Melting furnace operation; Energy input methods and controls; Air legislation and regulations; Soda lime emission mechanisms; and, Post furnace emission controls. Supporting papers are also included.

  14. Side-by-Side Field Evaluation of Highly Insulating Windows in the PNNL Lab Homes

    SciTech Connect (OSTI)

    Widder, Sarah H.; Parker, Graham B.; Baechler, Michael C.; Bauman, Nathan N.

    2012-08-01T23:59:59.000Z

    To examine the energy, air leakage, and thermal performance of highly insulating windows, a field evaluation was undertaken in a matched pair of all-electric, factory-built “Lab Homes” located on the Pacific Northwest National Laboratory (PNNL) campus in Richland, Washington. The “baseline” Lab Home B was retrofitted with “standard” double-pane clear aluminum-frame slider windows and patio doors, while the “experimental” Lab Home A was retrofitted with Jeld-Wen® triple-pane vinyl-frame slider windows and patio doors with a U-factor of 0.2 and solar heat gain coefficient of 0.19. To assess the window, the building shell air leakage, energy use, and interior temperatures of each home were compared during the 2012 winter heating and summer cooling seasons. The measured energy savings in Lab Home B averaged 5,821 watt-hours per day (Wh/day) during the heating season and 6,518 Wh/day during the cooling season. The overall whole-house energy savings of Lab Home B compared to Lab Home A are 11.6% ± 1.53% for the heating season and 18.4 ± 2.06% for the cooling season for identical occupancy conditions with no window coverings deployed. Extrapolating these energy savings numbers based on typical average heating degree days and cooling degree days per year yields an estimated annual energy savings of 12.2%, or 1,784 kWh/yr. The data suggest that highly insulating windows are an effective energy-saving measure that should be considered for high-performance new homes and in existing retrofits. However, the cost effectiveness of the measure, as determined by the simple payback period, suggests that highly insulating window costs continue to make windows difficult to justify on a cost basis alone. Additional reductions in costs via improvements in manufacturing and/or market penetration that continue to drive down costs will make highly insulating windows much more viable as a cost-effective energy efficiency measure. This study also illustrates that highly insulating windows have important impacts on peak load, occupant comfort, and condensation potential, which are not captured in the energy savings calculation. More consistent and uniform interior temperature distributions suggest that highly insulated windows, as part of a high performance building envelope, may enable more centralized duct design and downsized HVAC systems. Shorter, more centralized duct systems and smaller HVAC systems to yield additional cost savings, making highly insulating windows more cost effective as part of a package of new construction or retrofit measures which achieve significant reductions in home energy use.

  15. Magnetic behavior of erbium-zinc-borate glasses and glass ceramics

    SciTech Connect (OSTI)

    Borodi, G. [National Institute for Research and Development of Isotopic and Molecular Technologies, 65-103 Donath, 400293 Cluj-Napoca (Romania)] [National Institute for Research and Development of Isotopic and Molecular Technologies, 65-103 Donath, 400293 Cluj-Napoca (Romania); Pascuta, P.; Bosca, M.; Pop, V. [Technical University, 28 Memorandumului, 400114 Cluj-Napoca (Romania)] [Technical University, 28 Memorandumului, 400114 Cluj-Napoca (Romania); Stefan, R. [Agricultural Science and Veterinary Medicine University, 3-5 Calea Manastur, 400372 Cluj-Napoca (Romania)] [Agricultural Science and Veterinary Medicine University, 3-5 Calea Manastur, 400372 Cluj-Napoca (Romania); Tetean, R. [Babes-Bolyai University, 1 Mihail Kogalniceanu, Faculty of Physics, 400084 Cluj Napoca (Romania)] [Babes-Bolyai University, 1 Mihail Kogalniceanu, Faculty of Physics, 400084 Cluj Napoca (Romania); Radulescu, D. [University of Medicine and Pharmacy Iuliu Hatieganu, 8 Victor Babes, 400012 Cluj-Napoca (Romania)] [University of Medicine and Pharmacy Iuliu Hatieganu, 8 Victor Babes, 400012 Cluj-Napoca (Romania)

    2013-11-13T23:59:59.000Z

    Glasses of the system (Er{sub 2}O{sub 3}){sub x}?(B{sub 2}O{sub 3}){sub (60?x)}?(ZnO){sub 40} (3 ? x ? 15 mol%) were prepared by conventional melt quenching and subsequently converted to glass ceramics by heat treatment of glass samples at 860 °C for 2 h. The magnetic behaviour of the studied glasses and glass ceramics were investigated using a vibrating sample magnetometer (VSM) and a Faraday-type magnetic balance. Magnetic data show that erbium ions are involved in negative superexchange interactions in all the investigated samples, being antiferromagnetically coupled. For all studied samples the experimental values obtained for the effective magnetic moments are lower than the value corresponding to free Er{sup 3+} ions and decrease with the increasing of Er{sub 2}O{sub 3} content. The decrease is more pronounced in heat treated samples than untreated ones.

  16. Transport properties of lithium- lead-vanadium-telluride glass and glass ceramics

    SciTech Connect (OSTI)

    Sathish, M., E-mail: sathishphy79@gmail.com [Department of Physics, GOVT first grade College, Doddaballapur-561203 (India); Eraiah, B., E-mail: eraiah@rediffmail.com [Department of Physics, Bangalore University, Bangalore-560056, India (India)

    2014-04-24T23:59:59.000Z

    Glasses with the chemical composition 35Li{sub 2}O-(45-x)V{sub 2}O{sub 5?}20PbO-xTeO{sub 2} (where x = 2.5, 5, 7.5, 10, 15 mol %) have prepared by conventional melt quenching method. The electrical conductivity of Li{sup +} ion conducting lead vanadium telluride glass samples has been carried out both as a function of temperature and frequency in the temperature range 503K-563K and over frequencies 40 Hz to 10 MHz. The electronic conduction has been observed in the present systems. When these samples annealed around 400°C for 2hour become the glass ceramic, which also shows increase tendency of conductivity. SEM confines glass and glass ceramic nature of the prepared samples.

  17. Vacuum fusion bonding of glass plates

    DOE Patents [OSTI]

    Swierkowski, Steve P. (Livermore, CA); Davidson, James C. (Livermore, CA); Balch, Joseph W. (Livermore, CA)

    2001-01-01T23:59:59.000Z

    An improved apparatus and method for vacuum fusion bonding of large, patterned glass plates. One or both glass plates are patterned with etched features such as microstructure capillaries and a vacuum pumpout moat, with one plate having at least one hole therethrough for communication with a vacuum pumpout fixture. High accuracy alignment of the plates is accomplished by a temporary clamping fixture until the start of the fusion bonding heat cycle. A complete, void-free fusion bond of seamless, full-strength quality is obtained through the plates; because the glass is heated well into its softening point and because of a large, distributed force that is developed that presses the two plates together from the difference in pressure between the furnace ambient (high pressure) and the channeling and microstructures in the plates (low pressure) due to the vacuum drawn. The apparatus and method may be used to fabricate microcapillary arrays for chemical electrophoresis; for example, any apparatus using a network of microfluidic channels embedded between plates of glass or similar moderate melting point substrates with a gradual softening point curve, or for assembly of glass-based substrates onto larger substrates, such as in flat panel display systems.

  18. Vacuum fusion bonding of glass plates

    DOE Patents [OSTI]

    Swierkowski, Steve P. (Livermore, CA); Davidson, James C. (Livermore, CA); Balch, Joseph W. (Livermore, CA)

    2000-01-01T23:59:59.000Z

    An improved apparatus and method for vacuum fusion bonding of large, patterned glass plates. One or both glass plates are patterned with etched features such as microstructure capillaries and a vacuum pumpout moat, with one plate having at least one hole therethrough for communication with a vacuum pumpout fixture. High accuracy alignment of the plates is accomplished by a temporary clamping fixture until the start of the fusion bonding heat cycle. A complete, void-free fusion bond of seamless, full-strength quality is obtained through the plates; because the glass is heated well into its softening point and because of a large, distributed force that is developed that presses the two plates together from the difference in pressure between the furnace ambient (high pressure) and the channeling and microstructures in the plates (low pressure) due to the vacuum drawn. The apparatus and method may be used to fabricate microcapillary arrays for chemical electrophoresis; for example, any apparatus using a network of microfluidic channels embedded between plates of glass or similar moderate melting point substrates with a gradual softening point curve, or for assembly of glass-based substrates onto larger substrates, such as in flat panel display systems.

  19. Sealing glasses for titanium and titanium alloys

    DOE Patents [OSTI]

    Brow, Richard K. (Albuquerque, NM); McCollister, Howard L. (Albuquerque, NM); Phifer, Carol C. (Albuquerque, NM); Day, Delbert E. (Rolla, MO)

    1997-01-01T23:59:59.000Z

    Barium lanthanoborate sealing-glass compositions are provided comprising various combinations (in terms of mole-%) of boron oxide (B.sub.2 O.sub.3), barium oxide (BaO), lanthanum oxide (La.sub.2 O.sub.3), and at least one other oxide selected from the group consisting of aluminum oxide (Al.sub.2 O.sub.3), calcium oxide (CaO), lithium oxide (Li.sub.2 O), sodium oxide (Na.sub.2 O), silicon dioxide (SiO.sub.2), or titanium dioxide (TiO.sub.2). These sealing-glass compositions are useful for forming hermetic glass-to-metal seals with titanium and titanium alloys having an improved aqueous durability and favorable sealing characteristics. Examples of the sealing-glass compositions are provided having coefficients of thermal expansion about that of titanium or titanium alloys, and with sealing temperatures less than about 900.degree. C., and generally about 700.degree.-800.degree. C. The barium lanthanoborate sealing-glass compositions are useful for components and devices requiring prolonged exposure to moisture or water, and for implanted biomedical devices (e.g. batteries, pacemakers, defibrillators, pumps).

  20. Sealing glasses for titanium and titanium alloys

    DOE Patents [OSTI]

    Brow, R.K.; McCollister, H.L.; Phifer, C.C.; Day, D.E.

    1997-07-15T23:59:59.000Z

    Barium lanthanoborate sealing-glass compositions are provided comprising various combinations (in terms of mole-%) of boron oxide (B{sub 2}O{sub 3}), barium oxide (BaO), lanthanum oxide (La{sub 2}O{sub 3}), and at least one other oxide selected from the group consisting of aluminum oxide (Al{sub 2}O{sub 3}), calcium oxide (CaO), lithium oxide (Li{sub 2}O), sodium oxide (Na{sub 2}O), silicon dioxide (SiO{sub 2}), or titanium dioxide (TiO{sub 2}). These sealing-glass compositions are useful for forming hermetic glass-to-metal seals with titanium and titanium alloys having an improved aqueous durability and favorable sealing characteristics. Examples of the sealing-glass compositions are provided having coefficients of thermal expansion about that of titanium or titanium alloys, and with sealing temperatures less than about 900 C, and generally about 700--800 C. The barium lanthanoborate sealing-glass compositions are useful for components and devices requiring prolonged exposure to moisture or water, and for implanted biomedical devices (e.g. batteries, pacemakers, defibrillators, pumps). 1 fig.

  1. Retention of Halogens in Waste Glass

    SciTech Connect (OSTI)

    Hrma, Pavel R.

    2010-05-01T23:59:59.000Z

    In spite of their potential roles as melting rate accelerators and foam breakers, halogens are generally viewed as troublesome components for glass processing. Of five halogens, F, Cl, Br, I, and At, all but At may occur in nuclear waste. A nuclear waste feed may contain up to 10 g of F, 4 g of Cl, and ?100 mg of Br and I per kg of glass. The main concern is halogen volatility, producing hazardous fumes and particulates, and the radioactive iodine 129 isotope of 1.7x10^7-year half life. Because F and Cl are soluble in oxide glasses and tend to precipitate on cooling, they can be retained in the waste glass in the form of dissolved constituents or as dispersed crystalline inclusions. This report compiles known halogen-retention data in both high-level waste (HLW) and low-activity waste (LAW) glasses. Because of its radioactivity, the main focus is on I. Available data on F and Cl were compiled for comparison. Though Br is present in nuclear wastes, it is usually ignored; no data on Br retention were found.

  2. Analysis of oil-pipeline distribution of multiple products subject to delivery time-windows

    E-Print Network [OSTI]

    Jittamai, Phongchai

    2006-04-12T23:59:59.000Z

    This dissertation defines the operational problems of, and develops solution methodologies for, a distribution of multiple products into oil pipeline subject to delivery time-windows constraints. A multiple-product oil pipeline is a pipeline system...

  3. Galadriel: A Display List-Based Window Manager Graphics Workstation Division

    E-Print Network [OSTI]

    Lewis, Robert R.

    to a VAX (780) running an internal Tek version of (relatively standard) 4.2bsd UNIX. So far, it's been'' is about as close as we could come to a mythological ``window manager''. VAX and VT100 are trademarks

  4. Playing in the X-Games Window on the Extreme Universe

    E-Print Network [OSTI]

    Playing in the X-Games Window on the Extreme Universe Yucca Mountain The Unseen Scholars 1663 LOS, TECHNOLOGY, AND ENGINEERING 2 8 20 Trident MAJOR PLAYER IN THE X-GAMES OF CONTEMPORARY SCIENCE Yucca Mountain

  5. Electrochromic windows for commercial buildings: Monitored results from a full-scale testbed

    E-Print Network [OSTI]

    Lee, Eleanor S.; DiBartolomeo, Dennis L.; Selkowitz, Stephen E.

    2000-01-01T23:59:59.000Z

    electrochromic window products will appear on the market.market and technology assessments apply conventional life-cycle cost analysis methods to determine the viability of electrochromicmarket assessments have been conducted by industry, but this information remains proprietary. Electrochromic

  6. Thin Metal Oxide Films to Modify a Window Layer in CdTe-Based...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    for Improved Performance. Thin Metal Oxide Films to Modify a Window Layer in CdTe-Based Solar Cells for Improved Performance. Abstract: We report on CdSCdTe photovoltaic devices...

  7. Drafty Windows: Is it Better to Insulate or Replace Them? | Department...

    Broader source: Energy.gov (indexed) [DOE]

    expensive method is a simple window insulation kit, which includes a large sheet of plastic and double-sided tape; the most expensive (and most efficient) method is to replace...

  8. Low-e Storm Windows: Market Assessment and Pathways to Market Transformation

    SciTech Connect (OSTI)

    Cort, Katherine A.

    2013-06-08T23:59:59.000Z

    Field studies sponsored by the U.S. Department of Energy (DOE) have shown that the use of low-e storm windows can lead to significant heating and cooling energy savings in residential homes. This study examines the market for low-e storm windows based on market data, case studies, and recent experience with weatherization deployment programs. It uses information from interviews conducted with DOE researchers and industry partners involved in case studies and early deployment efforts related to low-e storm windows. In addition, this study examines potential barriers to market acceptance, assesses the market and energy savings potential, and identifies opportunities to transform the market for low-e storm windows and overcome market adoption barriers.

  9. Evaluation of NTE Windows and a Work-Based Method to Determine...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and a Work-Based Method to Determine In-Use Emissions of a Heavy-Duty Diesel Engine Evaluation of NTE Windows and a Work-Based Method to Determine In-Use Emissions of a...

  10. Window-Related Energy Consumption in the US Residential and Commercial Building Stock

    E-Print Network [OSTI]

    Apte, Joshua; Arasteh, Dariush

    2008-01-01T23:59:59.000Z

    window related primary energy consumption of the US building= 1.056 EJ. “Primary” energy consumption includes a site-to-the amount of primary energy consumption required by space

  11. Copper Doped GaAs Infrared Filter for the 8-13 m Atmospheric Window

    E-Print Network [OSTI]

    Peale, Robert E.

    regions of interest, such as atmospheric transmission windows. Filters exclude solar or thermal photonsCdTe is typically melt grown in a high temperature furnace. All three elements in this alloy are toxic. Stability

  12. Design and validation of an air window for a molten salt solar thermal receiver

    E-Print Network [OSTI]

    Paxson, Adam Taylor

    2009-01-01T23:59:59.000Z

    This thesis contributes to the development of Concentrating Solar Power (CSP) receivers and focuses on the design of an efficient aperture. An air window is proposed for use as the aperture of a CSP molten salt receiver ...

  13. Building America Webinar: Low-E Storms: The Next Big Thing in Window Retrofits

    Broader source: Energy.gov [DOE]

    Until recently, energy-efficient window retrofit options have largely been limited to repair or replacement; leaving the homeowner to decide between affordability and deeper energy savings.  A new...

  14. State-of-the-Art Highly Insulating Window Frames - Research and Market Review

    E-Print Network [OSTI]

    Gustavsen, Arild

    2008-01-01T23:59:59.000Z

    analysis investigation of a PVC window frame naturally agedThermix / TGI-wave 1.23 x 1.48 PVC profile with PUR (? =TOPLINE Plus Rahmenmaterial: PVC- Profile, Kammern mit PU

  15. [send to printer] [close this window] What's Happening from Environmental Building News

    E-Print Network [OSTI]

    [send to printer] [close this window] What's Happening from Environmental Building News July 1-by-step move toward the goals of Architecture 2030's "2030 Challenge" to eliminate fossil-fuel use in all new

  16. The development and evaluation of a neutron window filter facility utilizing the TAMU NSC TRIGA reactor

    E-Print Network [OSTI]

    Harding, Patricia Colleen

    2012-06-07T23:59:59.000Z

    THE DEVELOPMENT AND EVALUATION OF A NEUTRON WINDOW FILTER FACILITY UTILIZING THE TAMU NSC TRIGA REACTOR A Thesis by PATRICIA COLLEEN HARDING Submitted to the Graduate College of Texas AAM University in partial fulfillment of the requirement... for the degree of MASTER OF SCIENCE December 1982 Major Subject: Nuclear Engineering THE DEVELOPMENT AND EVALUATION OF A NEUTRON WINDOW FILTER FACILITY UTILIZING THE TAMU NSC TRIGA REACTOR A Thesis by PATRICIA COLLEEN HARDING Approved as to style...

  17. Sensitivity analysis of window characteristics and their interactions on thermal performance in residential buildings

    E-Print Network [OSTI]

    George, Julie N

    1996-01-01T23:59:59.000Z

    acheived during daytime heating hours contribute to energy conservation by reducing the amount of auxiliary heat required to keep the interior temperatures at the desired levels (Balcomb et al. 1984). Proper utilization of solar heat gains should... in the thermal mass will be released to keep the building warm (Balcomb et al. 1984). Proper shading of windows can also greatly affect their thermal performance. Windows with properly designed shading and orientation supply a major portion of a buildings...

  18. Wetting of metals and glasses on Mo

    SciTech Connect (OSTI)

    Saiz, Eduardo; Tomsia, Antoni P.; Saiz, Eduardo; Lopez-Esteban, Sonia; Benhassine, Mehdi; de Coninck, Joel; Rauch, Nicole; Ruehle, Manfred

    2008-01-08T23:59:59.000Z

    The wetting of low melting point metals and Si-Ca-Al-Ti-O glasses on molybdenum has been investigated. The selected metals (Au, Cu, Ag) form a simple eutectic with Mo. Metal spreading occurs under nonreactive conditions without interdiffusion or ridge formation. The metals exhibit low (non-zero) contact angles on Mo but this requires temperatures higher than 1100 C in reducing atmospheres in order to eliminate a layer of adsorbed impurities on the molybdenum surface. By controlling the oxygen activity in the furnace, glass spreading can take place under reactive or nonreactive conditions. We have found that in the glass/Mo system the contact angle does not decrease under reactive conditions. In all cases, adsorption from the liquid seems to accelerate the diffusivity on the free molybdenum surface.

  19. Irradiation effects on borosilicate waste glasses

    SciTech Connect (OSTI)

    Roberts, F.P.

    1980-06-01T23:59:59.000Z

    The effects of alpha decay on five borosilicate glasses containing simulated nuclear high-level waste oxides were studied. Irradiations carried out at room temperature were achieved by incorporating 1 to 8 wt % /sup 244/Cm/sub 2/O/sub 3/ in the glasses. Density changes and stored-energy build-up saturated at doses less than 2 x 10/sup 21/ alpha decays/kg. Damage manifested by stored energy was completely annealed at 633/sup 0/K. Positive and negative density changes were observed which never exceeded 1%. Irradiation had very little effect on mechanical strength or on chemical durability as measured by aqueous leach rates. Also, no effects were observed on the microstructure for vitreous waste glasses, although radiation-induced microcracking could be achieved on specimens that had been devitrified prior to irradiation.

  20. Glass/ceramic coatings for implants

    SciTech Connect (OSTI)

    Tomsia, Antoni P. (Pinole, CA); Saiz, Eduardo (Berkeley, CA); Gomez-Vega, Jose M. (Nagoya, JP); Marshall, Sally J. (Larkspur, CA); Marshall, Grayson W. (Larkspur, CA)

    2011-09-06T23:59:59.000Z

    Glass coatings on metals including Ti, Ti6A14V and CrCo were prepared for use as implants. The composition of the glasses was tailored to match the thermal expansion of the substrate metal. By controlling the firing atmosphere, time, and temperature, it was possible to control the reactivity between the glass and the alloy and to fabricate coatings (25-150 .mu.m thick) with excellent adhesion to the substrate. The optimum firing temperatures ranged between 800 and 840.degree. C. at times up to 1 min in air or 15 min in N.sub.2. The same basic technique was used to create multilayered coatings with concentration gradients of hydroxyapatite (HA) particles and SiO.sub.2.

  1. Glass Frit Clumping And Dusting

    SciTech Connect (OSTI)

    Steimke, J. L.

    2013-09-26T23:59:59.000Z

    DWPF mixes a slurry of glass frit (Frit 418) and dilute (1.5 wt%) formic acid solution with high level waste in the Slurry Mix Evaporator (SME). There would be advantages to introducing the frit in a non-slurry form to minimize water addition to the SME, however, adding completely dry frit has the potential to generate dust which could clog filters or condensers. Prior testing with another type of frit, Frit 320, and using a minimal amount of water reduced dust generation, however, the formation of hard clumps was observed. To examine options and behavior, a TTQAP [McCabe and Stone, 2013] was written to initiate tests that would address these concerns. Tests were conducted with four types of glass frit; Frit 320, DWPF Frit 418, Bekeson Frit 418 and Multi-Aspirator Frit 418. The last two frits are chemically identical to DWPF Frit 418 but smaller particles were removed by the respective vendors. Test results on Frit Clumping and Dusting are provided in this report. This report addresses the following seven questions. Short answers are provided below with more detailed answers to follow. 1. Will the addition of a small amount of water, 1.5 wt%, to dry DWPF Frit 418 greatly reduce the dust generation during handling at DWPF? a. Yes, a small scale test showed that adding a little water to the frit greatly reduced dust generation during handling. 2. Will the addition of small amounts of water to the frit cause clumping that will impair frit handling at DWPF? a. No, not with Frit 418. Although clumps were observed to form when 1.5 wt% water was mixed with DWPF Frit 418, then compressed and air-dried overnight, the clumps were easily crushed and did not form the hardened material noted when Frit 320 was tested. 3. What is the measured size distribution of dust generated when dry frit is handled? (This affects the feasibility and choice of processing equipment for removing the dust generating fraction of the frit before it is added to the SME.) a. The size distribution for the dust removed from fresh DWPF Frit 418 while it was being shaken in a small scale LabRAM test was measured. The median size on a volume basis was 7.6 ?m and 90% of the frit particles were between 1.6 and 28 ?m. The mass of dust collected using this test protocol was much less than 1% of the original frit. 4. Can the dust be removed in a small number of processing steps and without the larger frit particles continuing to spall additional dust sized particles? a. Test results using a LabRAM were inconclusive. The LaRAM performs less efficient particle size separation than the equipment used by Bekeson and Multi-Aspirator. 5. What particle size of frit is expected to create a dust problem? a. The original criterion for creating a dusting problem was those particle sizes that were readily suspended when being shaken. For that criterion calculations and Microtrac size analyses indicated that particles smaller than 37 ?m are likely dust generators. Subsequently a more sophisticated criterion for dust problem was considered, particle sizes that would become suspended in the air flow patterns inside the SME and possibly plug the condenser. That size may be larger than 37 ?m but has not yet been determined. 6. If particles smaller than 37 ?m are removed will bulk dust generation be eliminated? a. Video-taped tests were performed using three gallons each of three types of frit 418, DWPF frit, Bekeson frit and Multi-Aspirator frit. Frit was poured through air from a height of approximately eight feet into a container half filled with water. Pouring Bekeson frit or Multi-Aspirator frit generated markedly less visible dust, but there was still a significant amount, which still has the potential of causing a dust problem. 7. Can completely dry frit be poured into the SME without having dust plug the condenser at the top of the vessel? a. Because of the complexity of air currents inside the SME and the difficulty of defensible size scaling a more prototypical test will be required to answer this question. We recommend construction of a full scale

  2. Characterization of Energy Savings and Thermal Comfort Improvements Derived from Using Interior Storm Windows

    SciTech Connect (OSTI)

    Knox, Jake R.; Widder, Sarah H.

    2013-09-30T23:59:59.000Z

    This field study of a single historic home in Seattle, WA documents the performance of Indow Windows’s interior storm window inserts. Energy use and the temperature profile of the house were monitored before and after the installation of the window inserts and changes in the two recorded metrics were examined. Using the defined analysis approach, it was determined that the interior storm windows produced a 22% reduction of the HVAC energy bill and had an undetermined effect on the thermal comfort in the house. Although there was no measurable changes in the thermal comfort of the house, the occupant noted the house to be “warmer in the winter and cooler in the summer” and that the “temperatures are more even (throughout the house).” The interior storm windows were found to be not cost effective, largely due to the retrofits completed on its heating system. However, if the economic analysis was conducted based on the old heating system, a 72% efficient oil fired furnace, the Indow Windows proved to be economical and had a simple payback period of 9.0 years.

  3. High Power RF Tests on WR650 Pre-Stressed Planar Windows

    SciTech Connect (OSTI)

    Stirbet, Mircea [JLAB; Davis, G. Kirk [JLAB; Elliott, Thomas S. [JLAB; King, Larry [JLAB; Powers, Thomas J. [JLAB; Rimmer, Robert A. [JLAB; Walker, Richard L. [JLAB

    2009-11-01T23:59:59.000Z

    A new planar, ceramic window intended to be used with WR650 waveguide fundamental power couplers at 1300 MHz or 1500 MHz has been developed. It is based on the pre-stressed planar window concept tested in PEP II and LEDA. A test stand that made use of the 100kW CW 1500 MHz RF system in the JLAB FEL was commissioned and used to apply up to 80 kW traveling wave (TW)to the windows. Two different types of RF windows (brazed and diffusion bonded ceramics) with design specification of 50 kW CW in TW mode were successfully tested both as a gas barrier (intended to operate up to 2 psi) and as a vacuum barrier. The vacuum windows were able to maintain UHV quality vacuum and were successfully operated in the 10{sup -9} mbar range. An overview of the pre-stressed power windows, RF test stand, procedures and RF power testing results will be presented.

  4. Apparatus and method for in-situ cleaning of resist outgassing windows

    DOE Patents [OSTI]

    Klebanoff, Leonard E. (San Ramon, CA); Haney, Steven J. (Tracy, CA)

    2001-01-01T23:59:59.000Z

    An apparatus and method for in-situ cleaning of resist outgassing windows. The apparatus includes a chamber located in a structure, with the chamber having an outgassing window to be cleaned positioned in alignment with a slot in the chamber, whereby radiation energy passes through the window, the chamber, and the slot onto a resist-coated wafer mounted in the structure. The chamber is connected to a gas supply and the structure is connected to a vacuum pump. Within the chamber are two cylindrical sector electrodes and a filament is electrically connected to one sector electrode and a power supply. In a first cleaning method the sector electrodes are maintained at the same voltage, the filament is unheated, the chamber is filled with argon (Ar) gas under pressure, and the window is maintained at a zero voltage, whereby Ar ions are accelerated onto the window surface, sputtering away carbon deposits that build up as a result of resist outgassing. A second cleaning method is similar except oxygen gas (O.sub.2) is admitted to the chamber instead of Ar. These two methods can be carried out during lithographic operation. A third method, carried out during a maintenance period, involves admitting CO.sub.2 into the chamber, heating the filament to a point of thermionic emission, the sector electrodes are at different voltages, excited CO.sub.2 gas molecules are created which impact the carbon contamination on the window, and gasify it, producing CO gaseous products that are pumped away.

  5. PLUTONIUM SOLUBILITY IN HIGH-LEVEL WASTE ALKALI BOROSILICATE GLASS

    SciTech Connect (OSTI)

    Marra, J.; Crawford, C.; Fox, K.; Bibler, N.

    2011-01-04T23:59:59.000Z

    The solubility of plutonium in a Sludge Batch 6 (SB6) reference glass and the effect of incorporation of Pu in the glass on specific glass properties were evaluated. A Pu loading of 1 wt % in glass was studied. Prior to actual plutonium glass testing, surrogate testing (using Hf as a surrogate for Pu) was conducted to evaluate the homogeneity of significant quantities of Hf (Pu) in the glass, determine the most appropriate methods to evaluate homogeneity for Pu glass testing, and to evaluate the impact of Hf loading in the glass on select glass properties. Surrogate testing was conducted using Hf to represent between 0 and 1 wt % Pu in glass on an equivalent molar basis. A Pu loading of 1 wt % in glass translated to {approx}18 kg Pu per Defense Waste Processing Facility (DWPF) canister, or about 10X the current allowed limit per the Waste Acceptance Product Specifications (2500 g/m{sup 3} of glass or about 1700 g/canister) and about 30X the current allowable concentration based on the fissile material concentration limit referenced in the Yucca Mountain Project License Application (897 g/m{sup 3}3 of glass or about 600 g Pu/canister). Based on historical process throughput data, this level was considered to represent a reasonable upper bound for Pu loading based on the ability to provide Pu containing feed to the DWPF. The task elements included evaluating the distribution of Pu in the glass (e.g. homogeneity), evaluating crystallization within the glass, evaluating select glass properties (with surrogates), and evaluating durability using the Product Consistency Test -- Method A (PCT-A). The behavior of Pu in the melter was evaluated using paper studies and corresponding analyses of DWPF melter pour samples.The results of the testing indicated that at 1 wt % Pu in the glass, the Pu was homogeneously distributed and did not result in any formation of plutonium-containing crystalline phases as long as the glass was prepared under 'well-mixed' conditions. The incorporation of 1 wt % Pu in the glass did not adversely impact glass viscosity (as assessed using Hf surrogate) or glass durability. Finally, evaluation of DWPF glass pour samples that had Pu concentrations below the 897 g/m{sup 3} limit showed that Pu concentrations in the glass pour stream were close to targeted compositions in the melter feed indicating that Pu neither volatilized from the melt nor stratified in the melter when processed in the DWPF melter.

  6. Towards modeling gadolinium-lead-borate glasses

    SciTech Connect (OSTI)

    Rada, S., E-mail: Simona.Rada@phys.utcluj.ro [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania); Ristoiu, T. [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania)] [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania); Rada, M. [Department of Mechatronic, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania)] [Department of Mechatronic, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania); Coroiu, I. [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania)] [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania); Maties, V. [Department of Mechatronic, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania)] [Department of Mechatronic, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania); Culea, E. [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania)] [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania)

    2010-01-15T23:59:59.000Z

    Infrared spectra of gadolinium-lead-borate glasses of the xGd{sub 2}O{sub 3}.(100 - x)[3B{sub 2}O{sub 3}.PbO] system, where x = 0, 5, 10, 15, 25, 35 and 50 mol.%, have been recorded to explore the role of content of gadolinium ions behaving as glass modifier. The FTIR spectroscopy data for the xGd{sub 2}O{sub 3}.(1 - x)[3B{sub 2}O{sub 3}.PbO] glasses show the structural role of lead ions as a network-formers and of the gadolinium ions network modifiers. Adding of the rare earth ion up to 35 mol.% into the glass matrix, the IR bands characteristic to the studied glasses become sharper and more pronounced. Structural changes, as recognized by analyzing band shapes of IR spectra, revealed that Gd{sub 2}O{sub 3} causes a change from the continuous borate network to the continuous lead-borate network interconnected through Pb-O-B and B-O-B bridges and the transformation of some tetrahedral [BO{sub 4}] units into trigonal [BO{sub 3}] units. Then, gadolinium ions have affinity towards [BO{sub 3}] structural units which contain non-bridging oxygens necessary for the charge compensation because the more electronegative [BO{sub 3}] structural units were implied in the formation of B-O-Gd bonds and the transformation of glass network into a glass ceramic. We propose a possible structural model of building blocks for the formation of continuous random 3B{sub 2}O{sub 3}.PbO network glass used by density functional theory (DFT) calculations. DFT calculations show that lead atoms occupy three different sites in the proposed model. The first is coordinated with six oxygen atoms forming distorted octahedral geometries. The second lead atom has an octahedral oxygen environment and the five longer Pb-O bonds are considered as participating in the metal coordination scheme. The third lead atom has ionic character. In agreement with the results offered by the experimental FTIR data, the theoretical IR data confirm that our proposed structure is highly possible.

  7. Development of a Procedure to Evaluate the Shear Modulus of Laminated Glass Interlayers

    E-Print Network [OSTI]

    Brackin, Michael S.

    2010-07-14T23:59:59.000Z

    Laminated glass is comprised of multiple glass plates coupled together in a sandwich construction through the use of a polymorphous interlayer that acts as a bonding agent between the glass plates. Laminated glass offers several advantages over...

  8. Heavy Metals in Glass Beads Used in Pavement Markings

    E-Print Network [OSTI]

    Mangalgiri, Kiranmayi

    2012-07-16T23:59:59.000Z

    Pavement markings are vital for safely navigating roadways. The nighttime visibility of pavement markings is enhanced by addition of retroreflective glass beads, most of which are made from recycled glass. Concern has been raised over the presence...

  9. Combustion Technology Development for an Advanced Glass Melting System

    E-Print Network [OSTI]

    Stickler, D. B.; Westra, L.; Woodroffe, J.; Jeong, K. M.; Donaldson, L. W.

    Concept feasibility of an innovative technology for glass production has recently been demonstrated. It is based on suspension heating of the glass-forming batch minerals while entrained in a combustion flow of preheated air and natural gas...

  10. Structure and magnetic properties of vanadiumsodium silicate glasses

    E-Print Network [OSTI]

    Mekki, Abdelkarim

    Structure and magnetic properties of vanadium­sodium silicate glasses A. Mekki a,*, G.D. Khattak Received 4 April 2002 Abstract Vanadium­sodium silicate glasses with the chemical composition [ðV2O5�x(Na2O) atoms in the silicate glasses. The fraction of NBO, determined from these spectra is found to increase

  11. Optical absorption and ionization of silicate glasses Leonid B. Glebov

    E-Print Network [OSTI]

    Glebov, Leon

    Optical absorption and ionization of silicate glasses Leonid B. Glebov School of Optics and hydroxyl), and induced (color centers) absorption of multicomponent silicate glasses in UV, visible-photon ionization was detected in alkaline-silicate glasses exposed to high-power laser radiation in nano

  12. DWPF Glass Melter Technology Manual: Volume 3

    SciTech Connect (OSTI)

    Iverson, D.C.

    1993-12-31T23:59:59.000Z

    This document details information about the design of a glass melter to be used at the Defense Waste Processing Facility located at the Savannah River Site. Topics discussed include: Information collected during testing, equipment, materials, design basis, feed tubes, and an evaluation of the performance of various components. Information is conveyed using many diagrams and photographs.

  13. Equilibrium ultrastable glasses produced by random pinning

    E-Print Network [OSTI]

    Glen M Hocky; Ludovic Berthier; David R. Reichman

    2014-12-08T23:59:59.000Z

    Ultrastable glasses have risen to prominence due to their potentially useful material properties and the tantalizing possibility of a general method of preparation via vapor deposition. Despite the importance of this novel class of amorphous materials, numerical studies have been scarce because achieving ultrastability in atomistic simulations is an enormous challenge. Here we bypass this difficulty and establish that randomly pinning the position of a small fraction of particles inside an equilibrated supercooled liquid generates ultrastable configurations at essentially no numerical cost, while avoiding undesired structural changes due to the preparation protocol. Building on the analogy with vapor-deposited ultrastable glasses, we study the melting kinetics of these configurations following a sudden temperature jump into the liquid phase. In homogeneous geometries, we find that enhanced kinetic stability is accompanied by large scale dynamic heterogeneity, while a competition between homogeneous and heterogeneous melting is observed when a liquid boundary invades the glass at constant velocity. Our work demonstrates the feasibility of large-scale, atomistically resolved, and experimentally relevant simulations of the kinetics of ultrastable glasses.

  14. Erbium concentration dependent absorbance in tellurite glass

    SciTech Connect (OSTI)

    Sazali, E. S., E-mail: mdsupar@utm; Rohani, M. S., E-mail: mdsupar@utm; Sahar, M. R., E-mail: mdsupar@utm; Arifin, R., E-mail: mdsupar@utm; Ghoshal, S. K., E-mail: mdsupar@utm; Hamzah, K., E-mail: mdsupar@utm [Advanced Optical Material Research Group, Department of Physics, Faculty of Science, Universiti Teknologi Malaysia, 81310, Skudai, Johor Bahru, Johor (Malaysia)

    2014-09-25T23:59:59.000Z

    Enhancing the optical absorption cross-section in topically important rare earth doped tellurite glasses is challenging for photonic devices. Controlled synthesis and detailed characterizations of the optical properties of these glasses are important for the optimization. The influence of varying concentration of Er{sup 3+} ions on the absorbance characteristics of lead tellurite glasses synthesized via melt-quenching technique are investigated. The UV-Vis absorption spectra exhibits six prominent peaks centered at 490, 526, 652, 800, 982 and 1520 nm ascribed to the transitions in erbium ion from the ground state to the excited states {sup 4}F{sub 7/2}, {sup 2}H{sub 11/2}, {sup 4}F{sub 9/2}, {sup 4}I{sub 9/2}, {sup 2}H{sub 11/2} and {sup 4}I{sub 13/2}, respectively. The results are analyzed by means of optical band gap E{sub g} and Urbach energy E{sub u}. The values of the energy band gap are found decreased from 2.82 to 2.51 eV and the Urbach energy increased from 0.15 to 0.24 eV with the increase of the Er{sub 2}O{sub 3} concentration from 0 to 1.5 mol%. The excellent absorbance of the prepared tellurite glasses makes them suitable for fabricating solid state lasers.

  15. Mössbauer study of conductive oxide glass

    SciTech Connect (OSTI)

    Matsuda, Koken; Kubuki, Shiro [Tokyo Metropolitan University, Hachi-Oji, Tokyo 192-0397 (Japan); Nishida, Tetsuaki, E-mail: nishida@fuk.kindai.ac.jp [Kinki University, Iizuka, Fukuoka 820-8555 (Japan)

    2014-10-27T23:59:59.000Z

    Heat treatment of barium iron vanadate glass, BaO?Fe{sub 2}O{sub 3}?V{sub 2}O{sub 5}, at temperatures higher than crystallization temperature causes a marked decrease in resistivity (?) from several M?cm to several ?cm. {sup 57}Fe Mössbauer spectrum of heat-treated vanadate glass shows a marked decrease in quadrupole splitting (?) of Fe{sup III}, reflecting a structural relaxation, i.e., an increased symmetry of 'distorted' FeO{sub 4} and VO{sub 4} tetrahedra which are connected to each other by sharing corner oxygen atoms. Structural relaxation of 3D-network of vanadate glass accompanies a decrease in the activation energy for the conduction, reflecting a decreased energy gap between the donor level and conduction band. A marked increase in the conductivity was observed in CuO- or Cu{sub 2}O-containing barium iron vanadate glass after heat treatment at 450 °C for 30 min or more. 'n-type semiconductor model combined with small polaron hopping theory' was proposed in order to explain the high conductivity.

  16. DWPF Glass Melter Technology Manual: Volume 4

    SciTech Connect (OSTI)

    Iverson, D.C.

    1993-12-31T23:59:59.000Z

    This document details information about the design of a glass melter to be used at the Defense Waste Processing Facility located at the Savannah River Plant. Information contained in this document consists solely of a machine drawing and parts list and purchase orders with specifications of equipment used in the development of the melter.

  17. Blocking effect of crystal–glass interface in lanthanum doped barium strontium titanate glass–ceramics

    SciTech Connect (OSTI)

    Wang, Xiangrong [Beijing Fine Ceramics Laboratory, State Key Laboratory of New Ceramics and Fine Processing, Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China); Zhang, Yong, E-mail: yzhang@tsinghua.edu.cn [Beijing Fine Ceramics Laboratory, State Key Laboratory of New Ceramics and Fine Processing, Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China); Baturin, Ivan [Ferroelectric Laboratory, Institute of Natural Science, Ural Federal University, Ekaterinburg 620000 (Russian Federation); Liang, Tongxiang [Beijing Fine Ceramics Laboratory, State Key Laboratory of New Ceramics and Fine Processing, Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China)

    2013-10-15T23:59:59.000Z

    Graphical abstract: The blocking effect of the crystal–glass interface on the carrier transport behavior in the lanthanum doped barium strontium titanate glass–ceramics: preparation and characterization. - Highlights: • La{sub 2}O{sub 3} addition promotes the crystallization of the major crystalline phase. • The Z? and M? peaks exist a significant mismatch for 0.5 mol% La{sub 2}O{sub 3} addition. • The Z? and M? peaks separate obviously for 1.0 mol% La{sub 2}O{sub 3} addition. • Crystallite impedance decreases while crystal–glass interface impedance increases. • La{sub 2}O{sub 3} addition increases blocking factor of the crystal–glass interface. - Abstract: The microstructures and dielectric properties in La{sub 2}O{sub 3}-doped barium strontium titanate glass–ceramics have been investigated by scanning electron microscopy (SEM) and impedance spectroscopy. SEM analysis indicated that La{sub 2}O{sub 3} additive decreases the average crystallite size. Impedance spectroscopy revealed that the positions of Z? and M? peaks are close for undoped samples. When La{sub 2}O{sub 3} concentration is 0.5 mol%, the Z? and M? peaks show a significant mismatch. Furthermore, these peaks separate obviously for 1.0 mol% La{sub 2}O{sub 3} addition. With increasing La{sub 2}O{sub 3} concentration, the contribution of the crystallite impedance becomes smaller, while the contribution of the crystal–glass interface impedance becomes larger. More interestingly, it was found that La{sub 2}O{sub 3} additive increases blocking factor of the crystal–glass interface in the temperature range of 250–450 °C. This may be attributed to a decrease of activation energy of the crystallite and an increase of the crystal–glass interface area.

  18. The development of design factors for heat-strengthened and tempered glass based on the glass failure prediction model

    E-Print Network [OSTI]

    Oakes, Timothy Andrew

    1991-01-01T23:59:59.000Z

    of the interior. According to ASTM, the residual surface compression of tempered glass is defined to have a value of 10, 000 psi (68. 95 MPa) while heat-strengthened glass has residual compressive stresses greater than 3, 500 psi (24. 13 MPa) but less than 10..., 000 psi (68. 95 MPa) (ASTM, 1989). These residual surface compressive stresses must be overcome by mechanical stresses before the glass surfaces experience tension. Hence heat-strengthened and tempered glass are considerably stronger than annealed...

  19. Glasstech. Ber. Glass Sci. Technol. 75 C2 (2002) 1 Linear and Nonlinear Photoionization of Silicate Glasses

    E-Print Network [OSTI]

    Glebov, Leon

    Glasstech. Ber. Glass Sci. Technol. 75 C2 (2002) 1 Linear and Nonlinear Photoionization of Silicate, photoinduced phenomena, and laser-induced damage of silicate glasses. The discussion will be concentrated devices, such as alkaline-silicate, sodium-calcium-silicate, borosilicate, and lead- silicate glasses

  20. Energy Efficient Glass Melting - The Next Generation Melter

    SciTech Connect (OSTI)

    David Rue

    2008-03-01T23:59:59.000Z

    The objective of this project is to demonstrate a high intensity glass melter, based on the submerged combustion melting technology. This melter will serve as the melting and homogenization section of a segmented, lower-capital cost, energy-efficient Next Generation Glass Melting System (NGMS). After this project, the melter will be ready to move toward commercial trials for some glasses needing little refining (fiberglass, etc.). For other glasses, a second project Phase or glass industry research is anticipated to develop the fining stage of the NGMS process.

  1. Rapid process for producing transparent, monolithic porous glass

    DOE Patents [OSTI]

    Coronado, Paul R. (Livermore, CA)

    2006-02-14T23:59:59.000Z

    A process for making transparent porous glass monoliths from gels. The glass is produced much faster and in much larger sizes than present technology for making porous glass. The process reduces the cost of making large porous glass monoliths because: 1) the process does not require solvent exchange nor additives to the gel to increase the drying rates, 2) only moderate temperatures and pressures are used so relatively inexpensive equipment is needed, an 3) net-shape glass monoliths are possible using this process. The process depends on the use of temperature to control the partial pressure of the gel solvent in a closed vessel, resulting in controlled shrinking during drying.

  2. Sealed glass coating of high temperature ceramic superconductors

    DOE Patents [OSTI]

    Wu, W.; Chu, C.Y.; Goretta, K.C.; Routbort, J.L.

    1995-05-02T23:59:59.000Z

    A method and article of manufacture of a lead oxide based glass coating on a high temperature superconductor is disclosed. The method includes preparing a dispersion of glass powders in a solution, applying the dispersion to the superconductor, drying the dispersion before applying another coating and heating the glass powder dispersion at temperatures below oxygen diffusion onset and above the glass melting point to form a continuous glass coating on the superconductor to establish compressive stresses which enhance the fracture strength of the superconductor. 8 figs.

  3. An Experimental and Analytical Evaluation of Wall And Window Retrofit Configurations: Supporting the Residential Retrofit Best Practices Guide

    SciTech Connect (OSTI)

    Stovall, Therese K [ORNL; Petrie, Thomas [ORNL; Kosny, Jan [ORNL; Childs, Phillip W [ORNL; Atchley, Jerald Allen [ORNL; Hulvey, Kimberly D [ORNL

    2007-11-01T23:59:59.000Z

    A Retrofit Best Practices Guide was developed to encourage homeowners to consider energy conservation issues whenever they modify their siding or windows. In support of this guide, an experimental program was implemented to measure the performance of a number of possible wall siding and window retrofit configurations. Both thermal and air-leakage measurements were made for a 2.4 x 2.4 m (8 x 8 ft) wall section with and without a 0.9 x 1.2 m (3 x 4 ft) window. The windows tested were previously well-characterized at a dedicated window test facility. A computer model was also used to provide information for the Best Practices Guide. The experimental data for walls and windows were used in conjunction with this model to estimate the total annual energy savings for several typical houses in a number of different locations.

  4. DEVELOPMENT OF GLASS MATRICES FOR HLW RADIOACTIVE WASTES

    SciTech Connect (OSTI)

    Jantzen, C.

    2010-03-18T23:59:59.000Z

    Vitrification is currently the most widely used technology for the treatment of high level radioactive wastes (HLW) throughout the world. Most of the nations that have generated HLW are immobilizing in either borosilicate glass or phosphate glass. One of the primary reasons that glass has become the most widely used immobilization media is the relative simplicity of the vitrification process, e.g. melt waste plus glass forming frit additives and cast. A second reason that glass has become widely used for HLW is that the short range order (SRO) and medium range order (MRO) found in glass atomistically bonds the radionuclides and governs the melt properties such as viscosity, resistivity, sulphate solubility. The molecular structure of glass controls contaminant/radionuclide release by establishing the distribution of ion exchange sites, hydrolysis sites, and the access of water to those sites. The molecular structure is flexible and hence accounts for the flexibility of glass formulations to waste variability. Nuclear waste glasses melt between 1050-1150 C which minimizes the volatility of radioactive components such as Tc{sup 99}, Cs{sup 137}, and I{sup 129}. Nuclear waste glasses have good long term stability including irradiation resistance. Process control models based on the molecular structure of glass have been mechanistically derived and have been demonstrated to be accurate enough to control the world's largest HLW Joule heated ceramic melter in the US since 1996 at 95% confidence.

  5. Ammonia-treated phosphate glasses useful for sealing to metals

    DOE Patents [OSTI]

    Brow, R.K.; Day, D.E.

    1991-09-03T23:59:59.000Z

    A method of improving surface-dependent properties of phosphate glass such as durability and wear resistance without significantly affecting its thermal expansion coefficient is provided which comprises annealing the glass in a dry ammonia atmosphere at temperatures approximating the transition temperature of the glass. The ammonia annealing treatment of the present invention is carried out for a time sufficient to allow incorporation of a thin layer of nitrogen into the surface of the phosphate glass, and the treatment improves the durability of the glass without the reduction in the thermal expansion coefficient that has restricted the effectiveness of prior ammonia treatments. The improved phosphate glass resulting from this method is superior in wear resistance, yet maintains suitable thermal expansion properties so that it may be used effectively in a variety of applications requiring hermetic glass-metal seals.

  6. System and method for glass processing and temperature sensing

    DOE Patents [OSTI]

    Shepard, Chester L.; Cannon, Bret D.; Khaleel, Mohammad A.

    2004-09-28T23:59:59.000Z

    Techniques for measuring the temperature at various locations through the thickness of glass products and to control the glass processing operation with the sensed temperature information are disclosed. Fluorescence emission of iron or cerium in glass is excited and imaged onto segmented detectors. Spatially resolved temperature data are obtained through correlation of the detected photoluminescence signal with location within the glass. In one form the detected photoluminescence is compared to detected scattered excitation light to determine temperature. Stress information is obtained from the time history of the temperature profile data and used to evaluate the quality of processed glass. A heating or cooling rate of the glass is also controlled to maintain a predetermined desired temperature profile in the glass.

  7. Low melting high lithia glass compositions and methods

    DOE Patents [OSTI]

    Jantzen, Carol M.; Pickett, John B.; Cicero-Herman, Connie A.; Marra, James C.

    2003-09-23T23:59:59.000Z

    The invention relates to methods of vitrifying waste and for lowering the melting point of glass forming systems by including lithia formers in the glass forming composition in significant amounts, typically from about 0.16 wt % to about 11 wt %, based on the total glass forming oxides. The lithia is typically included as a replacement for alkali oxide glass formers that would normally be present in a particular glass forming system. Replacement can occur on a mole percent or weight percent basis, and typically results in a composition wherein lithia forms about 10 wt % to about 100 wt % of the alkali oxide glass formers present in the composition. The present invention also relates to the high lithia glass compositions formed by these methods. The invention is useful for stabilization of numerous types of waste materials, including aqueous waste uranium oxides The decrease in melting point achieved by the present invention desirably prevents volatilization of hazardous or radioactive species during vitrification.

  8. Glass transition and crystallization kinetics of a barium borosilicate glass by a non-isothermal method

    SciTech Connect (OSTI)

    Lopes, Andreia A. S.; Soares, Roque S.; Lima, Maria M. A.; Monteiro, Regina C. C., E-mail: rcm@fct.unl.pt [Department of Materials Science, CENIMAT/I3N, Faculty of Sciences and Technology, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal)

    2014-01-28T23:59:59.000Z

    The glass transition and crystallization kinetics of a glass with a molar composition 60BaO-30B{sub 2}O{sub 3}-10SiO{sub 2} were investigated by differential scanning calorimetry (DSC) under non-isothermal conditions. DSC curves exhibited an endothermic peak associated with the glass transition and two partially overlapped exothermic peaks associated with the crystallization of the glass. The dependence of the glass transition temperature (T{sub g}) and of the maximum crystallization temperature (T{sub p}) on the heating rate was used to determine the activation energy associated with the glass transition (E{sub g}), the activation energy for crystallization (E{sub c}), and the Avrami exponent (n). X-ray diffraction (XRD) revealed that barium borate (?-BaB{sub 2}O{sub 4}) was the first crystalline phase to be formed followed by the formation of barium silicate (Ba{sub 5}Si{sub 8}O{sub 21}). The variations of activation energy for crystallization and of Avrami exponent with the fraction of crystallization (?) were also examined. When the crystallization fraction (?) increased from 0.1 to 0.9, the value of local activation energy (E{sub c}(?)) decreased from 554 to 458?kJ/mol for the first exothermic peak and from 1104 to 831?kJ/mol for the second exothermic peak. The value determined for the Avrami exponent was near 2 indicating a similar one-dimensional crystallization mechanism for both crystalline phases. This was confirmed by the morphological studies performed by scanning electron microscopy (SEM) on glass samples heat-treated at the first and at the second crystallization temperatures.

  9. Database of Low-e Storm Window Energy Performance across U.S. Climate Zones

    SciTech Connect (OSTI)

    Culp, Thomas D.; Cort, Katherine A.

    2014-09-04T23:59:59.000Z

    This is an update of a report that describes process, assumptions, and modeling results produced Create a Database of U.S. Climate-Based Analysis for Low-E Storm Windows. The scope of the overall effort is to develop a database of energy savings and cost effectiveness of low-E storm windows in residential homes across a broad range of U.S. climates using the National Energy Audit Tool (NEAT) and RESFEN model calculations. This report includes a summary of the results, NEAT and RESFEN background, methodology, and input assumptions, and an appendix with detailed results and assumptions by cliamte zone.

  10. Loose abrasive slurries for optical glass lapping

    SciTech Connect (OSTI)

    Neauport, Jerome; Destribats, Julie; Maunier, Cedric; Ambard, Chrystel; Cormont, Philippe; Pintault, B.; Rondeau, Olivier

    2010-10-20T23:59:59.000Z

    Loose abrasive lapping is widely used to prepare optical glass before its final polishing. We carried out a comparison of 20 different slurries from four different vendors. Slurry particle sizes and morphologies were measured. Fused silica samples were lapped with these different slurries on a single side polishing machine and characterized in terms of surface roughness and depth of subsurface damage (SSD). Effects of load, rotation speed, and slurry concentration during lapping on roughness, material removal rate, and SSD were investigated.

  11. DWPF Glass Melter Technology Manual: Volume 1

    SciTech Connect (OSTI)

    Iverson, D.C.

    1993-12-31T23:59:59.000Z

    This document details information about the design of a glass melter to be used at the Defense Waste Processing Facility located at the Savannah River Site. Topics include: melter overview, design basis, materials, vessel configuration, insulation, refractory configuration, electrical isolation, electrodes, riser and pour spout heater design, dome heaters, feed tubes, drain valves, differential pressure pouring, and melter test results. Information is conveyed using many diagrams and photographs.

  12. Overview of Energy Efficiency for Glass Furnace

    E-Print Network [OSTI]

    Banerjee, Rangan

    ,Particulates (Environmental norms) Global competitiveness #12;3 April, 2006 4Source: www.oilnergy.com Crude Oil Price #12;3 April, 2006 5 Natural Gas Price Source: www.oilnergy.com #12;3 April, 2006 6 Carbon Dioxide Endothermic heat of reaction Glass enthalpy at outlet of tank 1886 From temperature of 20 oC to 1500 oC Batch

  13. Glass Property Models and Constraints for Estimating the Glass to be Produced at Hanford by Implementing Current Advanced Glass Formulation Efforts

    SciTech Connect (OSTI)

    Vienna, John D.; Kim, Dong-Sang; Skorski, Daniel C.; Matyas, Josef

    2013-07-31T23:59:59.000Z

    Recent glass formulation and melter testing data have suggested that significant increases in waste loading in HLW and LAW glasses are possible over current system planning estimates. The data (although limited in some cases) were evaluated to determine a set of constraints and models that could be used to estimate the maximum loading of specific waste compositions in glass. It is recommended that these models and constraints be used to estimate the likely HLW and LAW glass volumes that would result if the current glass formulation studies are successfully completed. It is recognized that some of the models are preliminary in nature and will change in the coming years. Plus the models do not currently address the prediction uncertainties that would be needed before they could be used in plant operations. The models and constraints are only meant to give an indication of rough glass volumes and are not intended to be used in plant operation or waste form qualification activities. A current research program is in place to develop the data, models, and uncertainty descriptions for that purpose. A fundamental tenet underlying the research reported in this document is to try to be less conservative than previous studies when developing constraints for estimating the glass to be produced by implementing current advanced glass formulation efforts. The less conservative approach documented herein should allow for the estimate of glass masses that may be realized if the current efforts in advanced glass formulations are completed over the coming years and are as successful as early indications suggest they may be. Because of this approach there is an unquantifiable uncertainty in the ultimate glass volume projections due to model prediction uncertainties that has to be considered along with other system uncertainties such as waste compositions and amounts to be immobilized, split factors between LAW and HLW, etc.

  14. Glazing materials for solar and architectural applications. Final report

    SciTech Connect (OSTI)

    Lampert, C.M. [ed.

    1994-09-01T23:59:59.000Z

    This report summarizes five collaborative research projects on glazings performed by participants in Subtask C of IEA Solar Heating and Cooling Programme (SHC) Task 10, Materials Research and Testing. The projects include materials characterization, optical and thermal measurements, and durability testing of several types of new glazings Three studies were completed on electrochromic and dispersed liquid crystals for smart windows, and two were completed for low-E coatings and transparent insulation materials for more conventional window and wall applications. In the area of optical switching materials for smart windows, the group developed more uniform characterization parameters that are useful to determine lifetime and performance of electrochromics. The detailed optical properties of an Asahi (Japan) prototype electrochromic window were measured in several laboratories. A one square meter array of prototype devices was tested outdoors and demonstrated significant cooling savings compared to tinted static glazing. Three dispersed liquid crystal window devices from Taliq (USA) were evaluated. In the off state, these liquid crystal windows scatter light greatly. When a voltage of about 100 V ac is applied, these windows become transparent. Undyed devices reduce total visible light transmittance by only .25 when switched, but this can be increased to .50 with the use of dyed liquid crystals. A wide range of solar-optical and emittance measurements were made on low-E coated glass and plastic. Samples of pyrolytic tin oxide from Ford glass (USA) and multilayer metal-dielectric coatings from Interpane (Germany) and Southwall (USA) were evaluated. In addition to optical characterization, the samples were exposure-tested in Switzerland. The thermal and optimal properties of two different types of transparent insulation materials were measured.

  15. Print this article Close This Window EU OKs India joining ITER nuclear reactor project

    E-Print Network [OSTI]

    Print this article Close This Window EU OKs India joining ITER nuclear reactor project Fri Dec 2-billion-euro project to build an experimental nuclear fusion reactor that in the long-run could provide virtually unlimited, cheap and clean energy. The EU's willingness to work with India on a civil nuclear

  16. Benefits of the International Residential Code's Maximum Solar heat Gain Coefficient Requirement for Windows

    E-Print Network [OSTI]

    Stone, G. A.; DeVito, E. M.; Nease, N. H.

    2002-01-01T23:59:59.000Z

    Texas adopted in its residential building energy code a maximum 0.40 solar heat gain coefficient (SHGC) for fenestration (e.g., windows, glazed doors and skylights)-a critical driver of cooling energy use, comfort and peak demand. An analysis...

  17. Combining MetaHeuristics to Effectively Solve the Vehicle Routing Problems with Time Windows

    E-Print Network [OSTI]

    Tam, Vincent W. L.

    ' requests with the minimal operational cost as usually measured by the number of vehicles used multiplied1 Combining Meta­Heuristics to Effectively Solve the Vehicle Routing Problems with Time Windows Engineering, The University of Hong Kong Pokfulam Road, Hong Kong. Department of Computer Science National

  18. Functional genomics as a window on radiation stress signaling Sally A Amundson*,1

    E-Print Network [OSTI]

    Functional genomics as a window on radiation stress signaling Sally A Amundson*,1 , Michael Bittner 20892, USA; 2 National Human Genome Research Institute, National Institutes of Health, Bethesda, MD before the completion of the human genome draft sequence, a number of techniques for genomic expression

  19. Boot Camp: System Requirements for Microsoft Windows Last Modified: June 17, 2008

    E-Print Network [OSTI]

    Papautsky, Ian

    Boot Camp: System Requirements for Microsoft Windows · Last Modified: June 17, 2008 · Article: HT1899 · Old Article: 306538 Summary Apple's Boot Camp software, included with Mac OS X 10.5 Leopard. System requirements To use Boot Camp with Mac OS X 10.5 you need the following: · An Intel-based Mac

  20. REAL-TIME DISPATCHING OF GUIDED AND UNGUIDED AUTOMOBILE SERVICE UNITS WITH SOFT TIME WINDOWS

    E-Print Network [OSTI]

    Krumke, Sven O.

    REAL-TIME DISPATCHING OF GUIDED AND UNGUIDED AUTOMOBILE SERVICE UNITS WITH SOFT TIME WINDOWS SVEN O that are no worse than 1% from optimum on state-of-the-art personal computers. 1. INTRODUCTION The German Automobile Association ADAC (Allgemeiner Deutscher Automobil- Club), the second largest automobile club worldwide

  1. REALTIME DISPATCHING OF GUIDED AND UNGUIDED AUTOMOBILE SERVICE UNITS WITH SOFT TIME WINDOWS

    E-Print Network [OSTI]

    Krumke, Sven O.

    REAL­TIME DISPATCHING OF GUIDED AND UNGUIDED AUTOMOBILE SERVICE UNITS WITH SOFT TIME WINDOWS SVEN O that are no worse than 1% from optimum on state­of­the­art personal computers. 1. INTRODUCTION The German Automobile Association ADAC (Allgemeiner Deutscher Automobil­ Club), the second largest automobile club worldwide

  2. Public release date: 6-Dec-2010 [ Print | E-mail | Share ] [ Close Window

    E-Print Network [OSTI]

    Espinosa, Horacio D.

    Public release date: 6-Dec-2010 [ Print | E-mail | Share ] [ Close Window ] Contact: Kyle Delaney k ubiquitously used metal, thin-film electrodes. The Northwestern University group in collaboration with SANDIA-like carbon electrodes rather than metal thin films and found a dramatic improvement in device robustness

  3. Dynamic Adaptation of Joint Transmission Power and Contention Window in VANET

    E-Print Network [OSTI]

    Weigle, Michele

    of transmission power is crucial. We propose to decrease the transmission power for high vehicle density or high penetration ratio and increase the transmission power for lower vehicle density or penetration ratioDynamic Adaptation of Joint Transmission Power and Contention Window in VANET 1 Danda B. Rawat, 2

  4. Two-Dimensional Computational Fluid Dynamics and Conduction Simulations of Heat Transfer in Window Frames

    E-Print Network [OSTI]

    1 Two-Dimensional Computational Fluid Dynamics and Conduction Simulations of Heat Transfer Arasteh and Dragan Curcija ABSTRACT Accurately analyzing heat transfer in window frame cavities radiation heat-transfer effects.) We examine three representative complex cavity cross-section profiles

  5. The Analysis and Design of Windowed Fourier Frame based Multiple Description Source Coding Schemes \\Lambda

    E-Print Network [OSTI]

    Balan, Radu V.

    transform. For the optimal windows, explicit representation formulas are obtained and non transform, redundant sets Acknowledgments The authors wish to thank the anonymous referees, no.7, November 2000, pp. 2491--2536 y current address: Siemens Corporate Research, 755 College Road

  6. The composite face illusion: A whole window into our understanding of holistic face perception

    E-Print Network [OSTI]

    Rossion, Bruno

    The composite face illusion: A whole window into our understanding of holistic face perception when the bottom halves are spatially offset: The composite face effect. This composite face paradigm our understanding of holistic face perception. Finally, I explain how this standard composite face

  7. High Accuracy 65nm OPC Verification: Full Process Window Model vs. Critical Failure ORC

    E-Print Network [OSTI]

    Boyer, Edmond

    High Accuracy 65nm OPC Verification: Full Process Window Model vs. Critical Failure ORC Amandine of Mask Rule Checking (MRC) and Optical Rule Checking (ORC) have become indispensable tools for ensuring, a technique known as Critical Failure ORC (CFORC) was introduced that uses optical parameters from aerial

  8. Lyman Maynard Stowe Library 1 of 5 PDA Troubleshooting Shots 2006 Install (Windows Mobile 5)

    E-Print Network [OSTI]

    Kim, Duck O.

    Lyman Maynard Stowe Library 1 of 5 PDA Troubleshooting Shots 2006 Install (Windows Mobile 5) Step 1: StrongARM Processor for Pocket PC 2003 and later o Under Pocket PC Mobile 5.0 Shots 2006 CAB File ­ locate and download (save) the file: Shots 2006 Mobile 5.0 CAB Need Help? CEC 679-8870 #12;Lyman Maynard

  9. Matching the waveform and the temporal window in the creation of experimental signals

    E-Print Network [OSTI]

    to a discrete-frequency representation in which the Fourier transform of the windowed signal preserves" wherein the power spectrum acquires power outside the frequency band of the original waveform. The spectrum be- comes a continuum with all frequencies, inside and outside the waveform band, represented more

  10. Fast and accurate direct MDCT to DFT conversion with arbitrary window functions

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 Fast and accurate direct MDCT to DFT conversion with arbitrary window functions Shuhua Zhang* and Laurent Girin Abstract--In this paper, we propose a method for direct con- version of MDCT coefficients of the MDCT-to- DFT conversion matrices into a Toeplitz part plus a Hankel part. The latter is split

  11. Journal of Biomedical Optics 16(2), 028004 (February 2011) Improving the therapeutic window of retinal

    E-Print Network [OSTI]

    Palanker, Daniel

    by coupling a 532-nm laser into a 200-m core multimode optical fiber at a 4­7 deg angle to normal incidenceJournal of Biomedical Optics 16(2), 028004 (February 2011) Improving the therapeutic window approaches toward increasing TW are investigated: (a) decreasing the central irradiance of the laser beam

  12. Calculation program for design of windows in residential buildings Ins Palma Santos and Svend Svendsen*

    E-Print Network [OSTI]

    sustainable buildings at the Department of Civil Engineering at the Technical University of Denmark1 Calculation program for design of windows in residential buildings InĂŞs Palma Santos and Svend Svendsen* Department of Civil Engineering, Brovej, Building 118, Technical University of Denmark, DK-2800

  13. A MODEL FOR THE FLEET SIZING OF DEMAND RESPONSIVE TRANSPORTATION SERVICES WITH TIME WINDOWS

    E-Print Network [OSTI]

    Dessouky, Maged

    A MODEL FOR THE FLEET SIZING OF DEMAND RESPONSIVE TRANSPORTATION SERVICES WITH TIME WINDOWS Marco a demand responsive transit service with a predetermined quality for the user in terms of waiting time models; Continuous approximation models; Paratransit services; Demand responsive transit systems. #12;3 1

  14. Planck 2015 results. IV. Low Frequency Instrument beams and window functions

    E-Print Network [OSTI]

    Ade, P A R; Ashdown, M; Aumont, J; Baccigalupi, C; Banday, A J; Barreiro, R B; Bartolo, N; Battaner, E; Benabed, K; Benoît, A; Benoit-Lévy, A; Bernard, J -P; Bersanelli, M; Bielewicz, P; Bonaldi, A; Bonavera, L; Bond, J R; Borrill, J; Bouchet, F R; Bucher, M; Burigana, C; Butler, R C; Calabrese, E; Cardoso, J -F; Catalano, A; Chamballu, A; Christensen, P R; Colombi, S; Colombo, L P L; Crill, B P; Curto, A; Cuttaia, F; Danese, L; Davies, R D; Davis, R J; de Bernardis, P; de Rosa, A; de Zotti, G; Delabrouille, J; Dickinson, C; Diego, J M; Dole, H; Donzelli, S; Doré, O; Douspis, M; Ducout, A; Dupac, X; Efstathiou, G; Elsner, F; Enßlin, T A; Eriksen, H K; Fergusson, J; Finelli, F; Forni, O; Frailis, M; Franceschi, E; Frejsel, A; Galeotta, S; Galli, S; Ganga, K; Giard, M; Giraud-Héraud, Y; Gjerlřw, E; González-Nuevo, J; Górski, K M; Gratton, S; Gregorio, A; Gruppuso, A; Hansen, F K; Hanson, D; Harrison, D L; Henrot-Versillé, S; Herranz, D; Hildebrandt, S R; Hivon, E; Hobson, M; Holmes, W A; Hornstrup, A; Hovest, W; Huffenberger, K M; Hurier, G; Jaffe, A H; Jaffe, T R; Juvela, M; Keihänen, E; Keskitalo, R; Kiiveri, K; Kisner, T S; Knoche, J; Kunz, M; Kurki-Suonio, H; Lähteenmäki, A; Lamarre, J -M; Lasenby, A; Lattanzi, M; Lawrence, C R; Leahy, J P; Leonardi, R; Lesgourgues, J; Levrier, F; Liguori, M; Lilje, P B; Linden-Vřrnle, M; Lindholm, V; López-Caniego, M; Lubin, P M; Macías-Pérez, J F; Maggio, G; Maino, D; Mandolesi, N; Mangilli, A; Martin, P G; Martínez-González, E; Masi, S; Matarrese, S; Mazzotta, P; McGehee, P; Meinhold, P R; Melchiorri, A; Mendes, L; Mennella, A; Migliaccio, M; Mitra, S; Montier, L; Morgante, G; Mortlock, D; Moss, A; Munshi, D; Murphy, J A; Naselsky, P; Nati, F; Natoli, P; Netterfield, C B; Nřrgaard-Nielsen, H U; Novikov, D; Novikov, I; Paci, F; Pagano, L; Paoletti, D; Partridge, B; Pasian, F; Patanchon, G; Pearson, T J; Perdereau, O; Perotto, L; Perrotta, F; Pettorino, V; Piacentini, F; Pierpaoli, E; Pietrobon, D; Pointecouteau, E; Polenta, G; Pratt, G W; Prézeau, G; Prunet, S; Puget, J -L; Rachen, J P; Rebolo, R; Reinecke, M; Remazeilles, M; Renzi, A; Rocha, G; Rosset, C; Rossetti, M; Roudier, G; Rubińo-Martín, J A; Rusholme, B; Sandri, M; Santos, D; Savelainen, M; Scott, D; Seiffert, M D; Shellard, E P S; Spencer, L D; Stolyarov, V; Sutton, D; Suur-Uski, A -S; Sygnet, J -F; Tauber, J A; Terenzi, L; Toffolatti, L; Tomasi, M; Tristram, M; Tucci, M; Tuovinen, J; Umana, G; Valenziano, L; Valiviita, J; Van Tent, B; Vassallo, T; Vielva, P; Villa, F; Wade, L A; Wandelt, B D; Watson, R; Wehus, I K; Yvon, D; Zacchei, A; Zonca, A

    2015-01-01T23:59:59.000Z

    This paper presents the characterization of the in-flight beams, the beam window functions, and the associated uncertainties for the Planck Low Frequency Instrument (LFI). The structure of the paper is similar to that presented in the 2013 Planck release; the main differences concern the beam normalization and the delivery of the window functions to be used for polarization analysis. The in-flight assessment of the LFI main beams relies on measurements performed during observations of Jupiter. By stacking data from seven Jupiter transits, the main beam profiles are measured down to -25 dB at 30 and 44 GHz, and down to -30 dB at 70 GHz. The agreement between the simulated beams and the measured beams is confirmed to be better than 1% at each LFI frequency band (within the 20 dB contour from the peak, the rms values are: 0.1% at 30 and 70 GHz; 0.2% at 44 GHz). Simulated polarized beams are used for the computation of the effective beam window functions. The error budget for the window functions is estimated fro...

  15. Service quality planning for freight distribution with time windows in large networks

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    as a quality factor of the service, since its nature and configuration also affects the total transportation1 Service quality planning for freight distribution with time windows in large networks Francesco introduces a methodology whose aim is to evaluate how the quality of a freight distribution service with time

  16. ADAPTIVE BLIND DECONVOLUTION OF LINEAR CHANNELS USING RENYI'S ENTROPY WITH PARZEN WINDOW ESTIMATION

    E-Print Network [OSTI]

    Slatton, Clint

    ADAPTIVE BLIND DECONVOLUTION OF LINEAR CHANNELS USING RENYI'S ENTROPY WITH PARZEN WINDOW ESTIMATION of Cantabria, Santander, Spain Abstract. Blind deconvolution of linear channels is a fundamental signal, as a criterion for blind deconvolution of linear channels. Comparisons between maximum and minimum entropy

  17. 1488 IEEE TRANSACTIONS ON COMMUNICATIONS, VOL. 49, NO. 8, AUGUST 2001 An Overlapping Window Decorrelating Multiuser

    E-Print Network [OSTI]

    Lu, Wu-Sheng

    1488 IEEE TRANSACTIONS ON COMMUNICATIONS, VOL. 49, NO. 8, AUGUST 2001 An Overlapping Window, University of Victoria, Victoria, BC V8W 3P6, Canada. He is now wit PMC-Sierrra Corporation, Burnaby, BC V5A of Electrical and Computer Engineering, University of Victoria, Victoria, BC V8W 3P6, Canada (e-mail: wslu

  18. NCEP Products Available to Distribute to CONDUIT High-Resolution Window Forecast System (HIRESW) Full

    E-Print Network [OSTI]

    NCEP Products Available to Distribute to CONDUIT Phase 1 High-Resolution Window Forecast System Ocean Forecast System (RTOFS) Full Description Product Location The RTOFS for the North Atlantic resolution nest Hurricane Weather Research and Forecast (HWRF) system Full Description Product Location (hwrf

  19. IEA-SHC Task 27: Environmental Performance Assessment of glazing and windows: context, overview, main concerns

    E-Print Network [OSTI]

    IEA-SHC Task 27: Environmental Performance Assessment of glazing and windows: context, overview and objectives, and most often of limited use in other contexts. A short review of the studies already performed the work undertaken within the programme of IEA/SHCP/Task 27, which will be presented in the third part

  20. Analysis of the Double Window in Saving Energy and Economical Efficiency in Nanjing in the Winter

    E-Print Network [OSTI]

    Zhang, Y.; He, J.; Gao, S.

    2006-01-01T23:59:59.000Z

    steel window can save energy by 37.68% is reached. As part of the economical efficiency analysis, an investment payback period is analyzed using the methods of static state and dynamic state. The analysis shows that by using single frame-double plastic...

  1. Energy performance of a dual airflow window under different climates Jingshu Wei1

    E-Print Network [OSTI]

    Chen, Qingyan "Yan"

    great po tential in conserving energy in buildings and provide fresh air to improve indoor air qua lity in fi ve different climate zones in China. The energy used by the apartment with blinds windows and low-e and by buildings in China acco unts for nearly 30 % o f the total primary energy and HVAC syste ms use 55

  2. Public release date: 19-Feb-2005 [ Print Article | E-mail Article | Close Window

    E-Print Network [OSTI]

    Hutchings, Jeffrey A.

    Rosenberg of the University of New Hampshire and a member of the U.S. Commission on Ocean Policy, and Jeremy Marine Fisheries Service, Andy Rosenberg has faced the difficult realities of implementing new fisheriesPublic release date: 19-Feb-2005 [ Print Article | E-mail Article | Close Window ] Contact: Jessica

  3. Close this window print this page MATSUSHITA BATTERY DEVELOPS NEW MICRO FUEL CELL

    E-Print Network [OSTI]

    to miniaturize the system, improve the reliability and reduce the cost. Notes and Technology Details 1. Fuel cellClose this window print this page MATSUSHITA BATTERY DEVELOPS NEW MICRO FUEL CELL TECHNOLOGY for fuel cells powering portable devices that makes it possible to reduce the size of the fuel cell to one

  4. Citations and renewal: A window into public and private patent value

    E-Print Network [OSTI]

    Sekhon, Jasjeet S.

    1 DRAFT Citations and renewal: A window into public and private patent value Alan C. Marco Deputy Chief Economist US Patent and Trademark Office1 24 February 2012 Abstract Using historical information on patent citations and patent maintenance in the US, I investigate the informational content provided

  5. THz detection of small molecule vapors in the atmospheric transmission windows

    E-Print Network [OSTI]

    Oklahoma State University

    transmission windows. We investigate two types of apparatus. In the first type the THz beam propagates along is controlled to simulate dry or humid conditions. In the second apparatus the THz beam propagates over a much brightness temperature spectra at near-millimeter and submillimeter wavelengths with a Fourier-transform

  6. THERM 5.2 / WINDOW 5.2 NFRC Simulation Manual

    E-Print Network [OSTI]

    of California. Ernest Orlando Lawrence Berkeley National Laboratory is an equal opportunity employer. #12;LBNLTHERM 5.2 / WINDOW 5.2 NFRC Simulation Manual Lawrence Berkeley National Laboratory JULY 2006 #12 Division Lawrence Berkeley National Laboratory Berkeley, California 94720 http

  7. Occupant Response to Window Control Signaling Systems; Appendix C: Mixed-mode Signal Case Study Summary

    E-Print Network [OSTI]

    Ackerly, Katie; Brager, Gail

    2011-01-01T23:59:59.000Z

    preventing energy waste during the red light mode is a moregreen lights was installed to help avoid energy waste, or inlight means that energy is being used to modify the temparature inside and therefore if I open my window it will waste energy.  

  8. Integrated Scheduling Using Rendezvous Window and Sniff Mode for Wireless Personal Area Networks

    E-Print Network [OSTI]

    Lee, Tae-Jin

    by connecting many light-weight personal devices such as PDAs, mobile phones, and media players. UWB (Ultra WideIntegrated Scheduling Using Rendezvous Window and Sniff Mode for Wireless Personal Area Networks and in a piconet level as well as power saving, which is desired for wireless personal area network systems. 1

  9. An empirical study of a full-scale polymer thermochromic window and its implications

    E-Print Network [OSTI]

    on material science development objectives Eleanor S. Lee Lawrence Berkeley National Laboratory Xiufeng Pang window and its implications on material science development objectives Eleanor S.Lee* Abstract , Xiufeng Pang, Sabine Hoffmann, C. Howdy Goudey, Anothai Thanachareonkit Building Technology and Urban Systems

  10. EMPIRICAL MODEL FOR FORMULATION OF CRYSTAL-TOLERANT HLW GLASSES

    SciTech Connect (OSTI)

    KRUGER AA; MATYAS J; HUCKLEBERRY AR; VIENNA JD; RODRIGUEZ CA

    2012-03-07T23:59:59.000Z

    Historically, high-level waste (HLW) glasses have been formulated with a low liquideus temperature (T{sub L}), or temperature at which the equilibrium fraction of spinel crystals in the melt is below 1 vol % (T{sub 0.01}), nominally below 1050 C. These constraints cannot prevent the accumulation of large spinel crystals in considerably cooler regions ({approx} 850 C) of the glass discharge riser during melter idling and significantly limit the waste loading, which is reflected in a high volume of waste glass, and would result in high capital, production, and disposal costs. A developed empirical model predicts crystal accumulation in the riser of the melter as a function of concentration of spinel-forming components in glass, and thereby provides guidance in formulating crystal-tolerant glasses that would allow high waste loadings by keeping the spinel crystals small and therefore suspended in the glass.

  11. Indentation size effect and the plastic compressibility of glass

    SciTech Connect (OSTI)

    Smedskjaer, Morten M., E-mail: mos@bio.aau.dk [Section of Chemistry, Aalborg University, 9000 Aalborg (Denmark)

    2014-06-23T23:59:59.000Z

    Oxide glasses exhibit significant densification under an applied isostatic pressure at the glass transition temperature. The glass compressibility is correlated with the chemical composition and atomic packing density, e.g., borate glasses with planar triangular BO{sub 3} units are more disposed for densification than silicate glasses with tetrahedral units. We here show that there is a direct relation between the plastic compressibility following hot isostatic compression and the extent of the indentation size effect (ISE), which is the decrease of hardness with indentation load exhibited by most materials. This could suggest that the ISE is correlated with indentation-induced shear bands, which should form in greater density when the glass network is more adaptable to volume changes through structural and topological rearrangements under an applied pressure.

  12. A New Optically Reflective Thin Layer Electrode (ORTLE) Window: Gold on a Thin Porous Alumina Film Used to Observe the

    E-Print Network [OSTI]

    Myrick, Michael Lenn

    the electrode face and a window behind it. The electrode is created by thin-film deposition of gold ontoFull Paper A New Optically Reflective Thin Layer Electrode (ORTLE) Window: Gold on a Thin Porous Alumina Film Used to Observe the Onset of Water Reduction Paul G. Miney, Maria V. Schiza, Michael L

  13. Figure 1. HomeWindow showing the energy usage of several monitors, displays, and computers with colored

    E-Print Network [OSTI]

    Greenberg, Saul

    Figure 1. HomeWindow showing the energy usage of several monitors, displays, and computers with colored auras. Red is high usage while green is low usage. HomeWindow: An Augmented Reality Domestic that reflects its current and historical energy use. Categories and Subject Descriptors H.5.2 [Information

  14. OPTIMIZATION OF GaN WINDOW LAYER FOR InGaN SOLAR CELLS USING POLARIZATION EFFECT

    E-Print Network [OSTI]

    Honsberg, Christiana

    on the design of wide-band gap GaN window layers for InGaN solar cells. Window layers serve to passivate the top into account during design of the solar cell to improve its collection efficiency. Previously, we have. The present work is a subset of the design optimization process for such solar cells, where we focus

  15. Where are Functions in PRISM 11.5.10? File Edit View Folder Tools Inquire Window Help

    E-Print Network [OSTI]

    Sibille, Etienne

    Where are Functions in PRISM 11.5.10? File Edit View Folder Tools Inquire Window Help New Help Desk ­ 412624help Switch Responsibility #12; Undo Typing Show Navigator New Acceptances View Lines Cascade Window Help Open Cut Zoom Open

  16. Method for forming glass-to-metal seals

    DOE Patents [OSTI]

    Kramer, Daniel P. (Dayton, OH); Massey, Richard T. (Hamilton, OH)

    1986-01-01T23:59:59.000Z

    A method for forming a glass-to-metal seal in which the glass has a higher melting point than the metal. The molten glass is vacuum injection molded onto the metal, thus melting a very thin layer of the surface of the metal long enough to form a seal, but not long enough to cause a distortion in the shape of the metal component.

  17. The use of glass matrices for solidification of radioactive wastes

    SciTech Connect (OSTI)

    Gromov, V.V.; Minaev, A.A. [Russian Academy of Sciences, Moscow (Russian Federation). Inst. of Physical Chemistry

    1993-12-31T23:59:59.000Z

    The physico-chemical aspects of the solidification of nuclear wastes have been studied at the Institute of Physical Chemistry of the Russian Academy of Sciences for a number of years. This method is viewed as the most reliable method of storage of nuclear wastes. Various glass systems have been studied, including phosphate, borosilicate glasses etc. The data obtained allow optimal glass compositions to be chosen for solidification of various nuclear wastes.

  18. Formulation and Characterization of Waste Glasses with Varying Processing Temperature

    SciTech Connect (OSTI)

    Kim, Dong-Sang; Schweiger, M. J.; Rodriguez, Carmen P.; Lepry, William C.; Lang, Jesse B.; Crum, Jarrod V.; Vienna, John D.; Johnson, Fabienne; Marra, James C.; Peeler, David K.

    2011-10-17T23:59:59.000Z

    This report documents the preliminary results of glass formulation and characterization accomplished within the finished scope of the EM-31 technology development tasks for WP-4 and WP-5, including WP-4.1.2: Glass Formulation for Next Generation Melter, WP-5.1.2.3: Systematic Glass Studies, and WP-5.1.2.4: Glass Formulation for Specific Wastes. This report also presents the suggested studies for eventual restart of these tasks. The initial glass formulation efforts for the cold crucible induction melter (CCIM), operating at {approx}1200 C, with selected HLW (AZ-101) and LAW (AN-105) successfully developed glasses with significant increase of waste loading compared to that is likely to be achieved based on expected reference WTP formulations. Three glasses formulated for AZ-101HLW and one glass for AN-105 LAW were selected for the initial CCIM demonstration melter tests. Melter tests were not performed within the finished scope of the WP-4.1.2 task. Glass formulations for CCIM were expanded to cover additional HLWs that have high potential to successfully demonstrate the unique advantages of the CCIM technologies based on projected composition of Hanford wastes. However, only the preliminary scoping tests were completed with selected wastes within the finished scope. Advanced glass formulations for the reference WTP melter, operating at {approx}1200 C, were initiated with selected specific wastes to determine the estimated maximum waste loading. The incomplete results from these initial formulation efforts are summarized. For systematic glass studies, a test matrix of 32 high-aluminum glasses was completed based on a new method developed in this study.

  19. Method and apparatus for removing and preventing window deposition during photochemical vapor deposition (photo-CVD) processes

    DOE Patents [OSTI]

    Tsuo, S.; Langford, A.A.

    1989-03-28T23:59:59.000Z

    Unwanted build-up of the film deposited on the transparent light-transmitting window of a photochemical vacuum deposition (photo-CVD) chamber is eliminated by flowing an etchant into the part of the photolysis region in the chamber immediately adjacent the window and remote from the substrate and from the process gas inlet. The respective flows of the etchant and the process gas are balanced to confine the etchant reaction to the part of the photolysis region proximate to the window and remote from the substrate. The etchant is preferably one that etches film deposit on the window, does not etch or affect the window itself, and does not produce reaction by-products that are deleterious to either the desired film deposited on the substrate or to the photolysis reaction adjacent the substrate. 3 figs.

  20. Method and apparatus for removing and preventing window deposition during photochemical vapor deposition (photo-CVD) processes

    DOE Patents [OSTI]

    Tsuo, Simon (Lakewood, CO); Langford, Alison A. (Boulder, CO)

    1989-01-01T23:59:59.000Z

    Unwanted build-up of the film deposited on the transparent light-transmitting window of a photochemical vacuum deposition (photo-CVD) chamber is eliminated by flowing an etchant into the part of the photolysis region in the chamber immediately adjacent the window and remote from the substrate and from the process gas inlet. The respective flows of the etchant and the process gas are balanced to confine the etchant reaction to the part of the photolysis region proximate to the window and remote from the substrate. The etchant is preferably one that etches film deposit on the window, does not etch or affect the window itself, and does not produce reaction by-products that are deleterious to either the desired film deposited on the substrate or to the photolysis reaction adjacent the substrate.

  1. China Glass Solar aka CG Solar formerly Weihai Bluestar Terra...

    Open Energy Info (EERE)

    Solar aka CG Solar formerly Weihai Bluestar Terra Photovoltaic Co Ltd Jump to: navigation, search Name: China Glass Solar (aka CG Solar, formerly Weihai Bluestar Terra Photovoltaic...

  2. Controlled permeation of hydrogen through glass. Final report

    SciTech Connect (OSTI)

    Halvorson, T. [Praxair, Inc., Tonawanda, NY (United States); Shelby, J.E. Jr. [Alfred Univ., NY (United States). Glass Science Lab.

    1998-03-01T23:59:59.000Z

    Storing hydrogen inside of hollow glass spheres requires that the gas permeate through the glass walls. Hydrogen permeation through glass is relatively slow and the time to charge a sphere or bed of spheres is dependent on many factors. Permeation processes are strongly temperature dependent with behavior that follows an Arrhenius function., Rate is also dependent on the pressure drop driving force across a membrane wall and inversely proportional to thickness. Once filled, glass spheres will immediately begin to leak once the pressure driving force is reversed. Practical systems would take advantage of the fact that keeping the glass at ambient temperatures can minimize outboard leakage even with significant internal pressures. If hydrogen could be loaded and unloaded from glass microspheres with significantly less energy and particularly at near ambient temperature, some of the key barriers to commercializing this storage concept would be broken and further system engineering efforts may make this approach cost-effective. There were two key objectives for this effort. The first was to evaluate the application of hollow glass microspheres for merchant hydrogen storage and distribution and then determine the hydrogen permeation performance required for practical commercial use. The second objective was to identify, through a series of fundamental experiments, a low energy, low temperature field effect that could significantly enhance hydrogen permeation through glass without application of heat. If such an effect could be found, hollow glass microspheres could be much more attractive for hydrogen storage or possibly gas separation applications.

  3. Welding/sealing glass-enclosed space in a vacuum

    DOE Patents [OSTI]

    Tracy, C. Edwin (Golden, CO); Benson, David K. (Golden, CO)

    1996-01-01T23:59:59.000Z

    A method of welding and sealing the edges of two juxtaposed glass sheets together to seal a vacuum space between the sheets comprises the steps of positioning a radiation absorbant material, such as FeO, VO.sub.2, or NiO, between the radiation transmissive glass sheets adjacent the edges and then irradiating the absorbant material, preferably with a laser beam, through at least one of the glass sheets. Heat produced by the absorbed radiation in the absorbant material melts glass in the portions of both glass sheets that are adjacent the absorbant material, and the melted glass from both sheets flows together to create the weld when the melted glass cools and hardens. The absorbant material can be dissolved and diffused into the melted glass to the extent that it no longer absorbs enough energy to keep the glass melted, thus, with appropriate proportioning of absorbant material to source energy power and welding heat needed, the process can be made self-stopping.

  4. Poisson's Ratio and the Densification of Glass under High Pressure

    SciTech Connect (OSTI)

    Rouxel, T.; Ji, H. [Applied Mechanics Laboratory of the University of Rennes 1, LARMAUR, Universite de Rennes 1, Campus de Beaulieu, 35042 Rennes cedex (France); Hammouda, T. [Laboratoire Magmas et Volcans, CNRS-OPG , Universite Blaise Pascal, 5 rue Kessler, 63038 Clermont-Ferrand cedex (France); Moreac, A. [IPR, CNRS-Universite de Rennes 1, Campus de Beaulieu, 35042 Rennes cedex (France)

    2008-06-06T23:59:59.000Z

    Because of a relatively low atomic packing density, (C{sub g}) glasses experience significant densification under high hydrostatic pressure. Poisson's ratio ({nu}) is correlated to C{sub g} and typically varies from 0.15 for glasses with low C{sub g} such as amorphous silica to 0.38 for close-packed atomic networks such as in bulk metallic glasses. Pressure experiments were conducted up to 25 GPa at 293 K on silica, soda-lime-silica, chalcogenide, and bulk metallic glasses. We show from these high-pressure data that there is a direct correlation between {nu} and the maximum post-decompression density change.

  5. Method of processing ``BPS`` glass ceramic and seals made therewith

    DOE Patents [OSTI]

    Reed, S.T.; Stone, R.G.; McCollister, H.L.; Wengert, P.R.

    1998-10-13T23:59:59.000Z

    A glass ceramic composition, a glass ceramic-to-metal seal, and more specifically a hermetic glass ceramic-to-metal seal prepared by subjecting a glass composition comprising, by weight percent, SiO{sub 2} (65--80%), LiO{sub 2} (8--16%), Al{sub 2}O{sub 3} (2--8%), K{sub 2}O (1--8%), P{sub 2}O{sub 5} (1--5%), B{sub 2}O{sub 3} (0.5--7%), and ZnO (0--5%) to the following processing steps: (1) heating the glass composition in a belt furnace to a temperature sufficient to melt the glass and crystallize lithium phosphate, (2) holding at a temperature and for a time sufficient to create cristobalite nuclei, (3) cooling at a controlled rate and to a temperature to cause crystallization of lithium silicates and growth of cristobalite, and (4) still further cooling in stages to ambient temperature. This process produces a glass ceramic whose high coefficient of thermal expansion (up to 200{times}10{sup {minus}7} in/in/C) permits the fabrication of glass ceramic-to-metal seals, and particularly hermetic glass ceramic seals to nickel-based and stainless steel alloys and copper. 5 figs.

  6. Method of processing "BPS" glass ceramic and seals made therewith

    DOE Patents [OSTI]

    Reed, Scott T. (Albuquerque, NM); Stone, Ronald G. (Albuquerque, NM); McCollister, Howard L. (Albuquerque, NM); Wengert, deceased, Paul R. (late of Albuquerque, NM)

    1998-01-01T23:59:59.000Z

    A glass ceramic composition, a glass ceramic-to-metal seal, and more specifically a hermetic glass ceramic-to-metal seal prepared by subjecting a glass composition comprising, by weight percent, SiO.sub.2 (65-80%), LiO.sub.2 (8-16%), Al.sub.2 O.sub.3 (2-8%), K.sub.2 O (1-8%), P.sub.2 O.sub.5 (1-5%), B.sub.2 O.sub.3 (0.5-7%), and ZnO (0-5%) to the following processing steps: 1) heating the glass composition in a belt furnace to a temperature sufficient to melt the glass and crystallize lithium phosphate, 2) holding at a temperature and for a time sufficient to create cristobalite nuclei, 3) cooling at a controlled rate and to a temperature to cause crystallization of lithium silicates and growth of cristobalite, and 4) still further cooling in stages to ambient temperature. This process produces a glass ceramic whose high coefficient of thermal expansion (up to 200.times.10.sup.-7 in/in/.degree.C.) permits the fabrication of glass ceramic-to-metal seals, and particularly hermetic glass ceramic seals to nickel-based and stainless steel alloys and copper.

  7. From local to global ground states in Ising spin glasses

    E-Print Network [OSTI]

    Ilia Zintchenko; Matthew B. Hastings; Matthias Troyer

    2015-01-09T23:59:59.000Z

    We consider whether it is possible to find ground states of frustrated spin systems by solving them locally. Using spin glass physics and Imry-Ma arguments in addition to numerical benchmarks we quantify the power of such local solution methods and show that for the average low-dimensional spin glass problem outside the spin- glass phase the exact ground state can be found in polynomial time. In the second part we present a heuristic, general-purpose hierarchical approach which for spin glasses on chimera graphs and lattices in two and three dimensions outperforms, to our knowledge, any other solver currently around, with significantly better scaling performance than simulated annealing.

  8. Welding/sealing glass-enclosed space in a vacuum

    DOE Patents [OSTI]

    Tracy, C.E.; Benson, D.K.

    1996-02-06T23:59:59.000Z

    A method of welding and sealing the edges of two juxtaposed glass sheets together to seal a vacuum space between the sheets comprises the steps of positioning a radiation absorbent material, such as FeO, VO{sub 2}, or NiO, between the radiation transmissive glass sheets adjacent the edges and then irradiating the absorbent material, preferably with a laser beam, through at least one of the glass sheets. Heat produced by the absorbed radiation in the absorbent material melts glass in the portions of both glass sheets that are adjacent the absorbent material, and the melted glass from both sheets flows together to create the weld when the melted glass cools and hardens. The absorbent material can be dissolved and diffused into the melted glass to the extent that it no longer absorbs enough energy to keep the glass melted, thus, with appropriate proportioning of absorbent material to source energy power and welding heat needed, the process can be made self-stopping. 8 figs.

  9. Metal and Glass Manufacturers Reduce Costs by Increasing Energy...

    Broader source: Energy.gov (indexed) [DOE]

    in Process Heating Systems Process heating plays a key role in producing steel, aluminum, and glass and in manufacturing products made from these materials. Faced with...

  10. Alkali-lead-iron phosphate glass and associated method

    DOE Patents [OSTI]

    Boatner, L.A.; Sales, B.C.; Franco, S.C.S.

    1994-03-29T23:59:59.000Z

    A glass composition and method of preparation utilizes a mixture consisting of phosphorus oxide within the range of about 40 to 49 molar percent, lead oxide within the range of about 10 to 25 molar percent, iron oxide within the range of about 10 to 17 molar percent and an alkali oxide within the range of about 23 to 30 molar percent. The glass resulting from the melting and subsequent solidifying of the mixture possesses a high degree of durability and a coefficient of thermal expansion as high as that of any of a number of metals. Such features render this glass highly desirable in glass-to-metal seal applications. 6 figures.

  11. Alkali-lead-iron phosphate glass and associated method

    DOE Patents [OSTI]

    Boatner, Lynn A. (Oak Ridge, TN); Sales, Brian C. (Knoxville, TN); Franco, Sofia C. S. (Santafe de Bogota, CO)

    1994-01-01T23:59:59.000Z

    A glass composition and method of preparation utilizes a mixture consisting of phosphorus oxide within the range of about 40 to 49 molar percent, lead oxide within the range of about 10 to 25 molar percent, iron oxide within the range of about 10 to 17 molar percent and an alkali oxide within the range of about 23 to 30 molar percent. The glass resulting from the melting and subsequent solidifying of the mixture possesses a high degree of durability and a coefficient of thermal expansion as high as that of any of a number of metals. Such features render this glass highly desirable in glass-to-metal seal applications.

  12. alternatives glass jars: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Small amounts). When looking at the cost effectiveness of recycling versus waste to landfill, it's worth bearing Melham, Tom 100 Overview of Energy Efficiency for Glass...

  13. Potential for energy conservation in the glass industry

    SciTech Connect (OSTI)

    Garrett-Price, B.A.; Fassbender, A.G.; Bruno, G.A.

    1986-06-01T23:59:59.000Z

    While the glass industry (flat glass, container glass, pressed and blown glass, and insulation fiber glass) has reduced its specific energy use (Btu/ton) by almost 30% since 1972, significant potential for further reduction still remains. State-of-the-art technologies are available which could lead to incremental improvements in glass industry energy productivity; however, these technologies must compete for capital with projects undertaken for other reasons (e.g., capacity expansion, equipment rebuild, labor cost reduction, product quality improvement, or compliance with environmental, health or safety regulations). Narrowing profit margins in the large tonnage segments of the glass industry in recent years and the fact that energy costs represent less than 25% of the value added in glass manufacture have combined to impede the widespread adoption of many state-of-the-art conservation technologies. Savings in energy costs alone have not provided the incentive to justify the capital expenditures required to realize the energy savings. Beyond implementation of state-of-the-art technologies, significant potential energy savings could accrue from advanced technologies which represent a radical departure from current glass making technology. Long-term research and development (R and D) programs, which address the technical and economic barriers associated with advanced, energy-conserving technologies, offer the opportunity to realize this energy-saving potential.

  14. aging colloidal glass: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Matter (arXiv) Summary: We use confocal microscopy to directly visualize the dynamics of aging colloidal glasses. We prepare a colloidal suspension at high density, a...

  15. Thermal Predictions of the Cooling of Waste Glass Canisters

    SciTech Connect (OSTI)

    Donna Post Guillen

    2014-11-01T23:59:59.000Z

    Radioactive liquid waste from five decades of weapons production is slated for vitrification at the Hanford site. The waste will be mixed with glass forming additives and heated to a high temperature, then poured into canisters within a pour cave where the glass will cool and solidify into a stable waste form for disposal. Computer simulations were performed to predict the heat rejected from the canisters and the temperatures within the glass during cooling. Four different waste glass compositions with different thermophysical properties were evaluated. Canister centerline temperatures and the total amount of heat transfer from the canisters to the surrounding air are reported.

  16. Research Needs: Glass Solar Reflectance and Vinyl Siding

    E-Print Network [OSTI]

    Hart, Robert

    2012-01-01T23:59:59.000Z

    properties of reflected solar radiation from glass surfaces,transfer at the siding surface. Direct solar radiation tosiding, reflected solar radiation from nearby surfaces,

  17. Molten Glass for Thermal Storage: Advanced Molten Glass for Heat Transfer and Thermal Energy Storage

    SciTech Connect (OSTI)

    None

    2012-01-01T23:59:59.000Z

    HEATS Project: Halotechnics is developing a high-temperature thermal energy storage system using a new thermal-storage and heat-transfer material: earth-abundant and low-melting-point molten glass. Heat storage materials are critical to the energy storage process. In solar thermal storage systems, heat can be stored in these materials during the day and released at night—when the sun is not out—to drive a turbine and produce electricity. In nuclear storage systems, heat can be stored in these materials at night and released to produce electricity during daytime peak-demand hours. Halotechnics new thermal storage material targets a price that is potentially cheaper than the molten salt used in most commercial solar thermal storage systems today. It is also extremely stable at temperatures up to 1200°C—hundreds of degrees hotter than the highest temperature molten salt can handle. Being able to function at high temperatures will significantly increase the efficiency of turning heat into electricity. Halotechnics is developing a scalable system to pump, heat, store, and discharge the molten glass. The company is leveraging technology used in the modern glass industry, which has decades of experience handling molten glass.

  18. The Conservation of Seventeenth Century Archaeological Glass

    E-Print Network [OSTI]

    Arcak, Cory

    2010-10-12T23:59:59.000Z

    . These materials are melted together in a heat resistant container or crucible. Once melted to the consistency of a molten liquid, the material is either cast, poured into a mold or is blown. Glass blowing is accomplished by gathering the molten material onto a... the materials and manipulate the molten mass through the various stages of glassmaking. Alkalis commonly used for glassmaking are derived from the ashes of plants and trees and are referred to as soda ash (sodium carbonate) and potash (potassium carbonate...

  19. Bioactive Glass Scaffolds for Bone Regeneration

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth (AOD)ProductssondeadjustsondeadjustAboutScienceCareers Apply for aCould WorkVehicles andBioactive Glass

  20. Analysis and Research on the Thermal Properties of Energy-efficient Building Glass: A Case Study in PVB Laminated Glass

    E-Print Network [OSTI]

    Chen, Z.; Meng, Q.

    2006-01-01T23:59:59.000Z

    , are analyzed. The methods on usage of energy-saving glass are promoted based on the differences of their thermal properties. Meanwhile, a new kind of glass?PVB laminated glass (Fig.1), is introduced. Fl at cl ear gl ass 0. 05mmLOWE coati ng Fl at cl ear g... lass 3 mm( 5 mm) 0. 38mmPVB 3 mm( 5 mm) 0. 38mmPVB Fig. 1 Structure of PVB laminated glass ICEBO2006, Shenzhen, China Envelope Technologies for Building Energy Efficiency, Vol.II-4-5 2. EVALUATION STANDARDS OF SOLAR-OPTICAL PROPERTY The main...

  1. Synthesis of nanocrystals in KNb(Ge,Si)O{sub 5} glasses and chemical etching of nanocrystallized glass fibers

    SciTech Connect (OSTI)

    Enomoto, Itaru [Department of Materials Science and Technology, Nagaoka University of Technology, 1603-1 Kamitomioka-cho, Nagaoka 940-2188 (Japan); Benino, Yasuhiko [Department of Materials Science and Technology, Nagaoka University of Technology, 1603-1 Kamitomioka-cho, Nagaoka 940-2188 (Japan); Fujiwara, Takumi [Department of Materials Science and Technology, Nagaoka University of Technology, 1603-1 Kamitomioka-cho, Nagaoka 940-2188 (Japan); Komatsu, Takayuki [Department of Materials Science and Technology, Nagaoka University of Technology, 1603-1 Kamitomioka-cho, Nagaoka 940-2188 (Japan)]. E-mail: komatsu@chem.nagaokaut.ac.jp

    2006-06-15T23:59:59.000Z

    The nanocrystallization behavior of 25K{sub 2}O-25Nb{sub 2}O{sub 5}-(50-x)GeO{sub 2}-xSiO{sub 2} glasses with x=0,25,and50 (i.e., KNb(Ge,Si)O{sub 5} glasses) and the chemical etching behavior of transparent nanocrystallized glass fibers have been examined. All glasses show nanocrystallization, and the degree of transparency of the glasses studied depends on the heat treatment temperature. Transparent nanocrystallized glasses can be obtained if the glasses are heat treated at the first crystallization peak temperature. Transparent nanocrystallized glass fibers with a diameter of about 100{mu}m in 25K{sub 2}O-25Nb{sub 2}O{sub 5}-50GeO{sub 2} are fabricated, and fibers with sharpened tips (e.g., the taper length is about 450{mu}m and the tip angle is about 12{sup o}) are obtained using a meniscus chemical etching method, in which etching solutions of 10wt%-HF/hexane and 10M-NaOH/hexane are used. Although the tip (aperture size) has not a nanoscaled size, the present study suggests that KNb(Ge,Si)O{sub 5} nanocrystallized glass fibers have a potential for new near-field optical fiber probes with high refractive indices of around n=1.8 and high dielectric constants of around {epsilon}=58 (1kHz, room temperature)

  2. Optical Basicity and Nepheline Crystallization in High Alumina Glasses

    SciTech Connect (OSTI)

    Rodriguez, Carmen P.; McCloy, John S.; Schweiger, M. J.; Crum, Jarrod V.; Winschell, Abigail E.

    2011-02-25T23:59:59.000Z

    The purpose of this study was to find compositions that increase waste loading of high-alumina wastes beyond what is currently acceptable while avoiding crystallization of nepheline (NaAlSiO4) on slow cooling. Nepheline crystallization has been shown to have a large impact on the chemical durability of high-level waste glasses. It was hypothesized that there would be some composition regions where high-alumina would not result in nepheline crystal production, compositions not currently allowed by the nepheline discriminator. Optical basicity (OB) and the nepheline discriminator (ND) are two ways of describing a given complex glass composition. This report presents the theoretical and experimental basis for these models. They are being studied together in a quadrant system as metrics to explore nepheline crystallization and chemical durability as a function of waste glass composition. These metrics were calculated for glasses with existing data and also for theoretical glasses to explore nepheline formation in Quadrant IV (passes OB metric but fails ND metric), where glasses are presumed to have good chemical durability. Several of these compositions were chosen, and glasses were made to fill poorly represented regions in Quadrant IV. To evaluate nepheline formation and chemical durability of these glasses, quantitative X-ray diffraction (XRD) analysis and the Product Consistency Test were conducted. A large amount of quantitative XRD data is collected here, both from new glasses and from glasses of previous studies that had not previously performed quantitative XRD on the phase assemblage. Appendix A critically discusses a large dataset to be considered for future quantitative studies on nepheline formation in glass. Appendix B provides a theoretical justification for choice of the oxide coefficients used to compute the OB criterion for nepheline formation.

  3. Energy Data Sourcebook for the U.S. Residential Sector

    E-Print Network [OSTI]

    Wenzel, T.P.

    2010-01-01T23:59:59.000Z

    80%glass, low emissivity film Wood Frame Window, 80%glass,low emissivity film, argon fill Wood Frame Window, 80%glass,

  4. Graded index antireflective coatings for glass : final report, September 1978 - February 1982

    E-Print Network [OSTI]

    Haggerty, John Scarseth

    1983-01-01T23:59:59.000Z

    Glass compositions and process conditions by which broad band gradedindex antreflective films can be produced on glass surfaces have been developed. The end use for the treated glass sheet is as cover plates for flat plate ...

  5. The effect of temperature on the bending of laminated glass beams

    E-Print Network [OSTI]

    Edel, Matthew Thomas

    1997-01-01T23:59:59.000Z

    Laminated glass is comprised of multiple plates of glass bonded together with polymorphous interlayers. The interest in the use of architectural laminated glass in the construction industry has increased due to its possible advantages over...

  6. Initial Examination of Low Velocity Sphere Impact of Glass Ceramics

    SciTech Connect (OSTI)

    Morrissey, Timothy G [ORNL; Fox, Ethan E [ORNL; Wereszczak, Andrew A [ORNL; Ferber, Mattison K [ORNL

    2012-06-01T23:59:59.000Z

    This report summarizes US Army TARDEC sponsored work at Oak Ridge National Laboratory (ORNL) involving low velocity (< 30 m/s or < 65 mph) sphere impact testing of two materials from the lithium aluminosilicate family reinforced with different amounts of ceramic particulate, i.e., glass-ceramic materials, SCHOTT Resistan{trademark}-G1 and SCHOTT Resistan{trademark}-L. Both materials are provided by SCHOTT Glass (Duryea, PA). This work is a follow-up to similar sphere impact studies completed by the authors on PPG's Starphire{reg_sign} soda-lime silicate glass and SCHOTT BOROFLOAT{reg_sign} borosilicate glass. A gas gun or a sphere-drop test setup was used to produce controlled velocity delivery of silicon nitride (Si{sub 3}N{sub 4}) spheres against the glass ceramic tile targets. Minimum impact velocities to initiate fracture in the glass-ceramics were measured and interpreted in context to the kinetic energy of impact and the elastic property mismatch between sphere and target material. Quasistatic spherical indentation was also performed on both glass ceramics and their contact damage responses were compared to those of soda-lime silicate and borosilicate glasses. Lastly, variability of contact damage response was assessed by performing spherical indentation testing across the area of an entire glass ceramic tile. The primary observations from this low velocity (< 30 m/s or < 65 mph) testing were: (1) Resistan{trademark}-L glass ceramic required the highest velocity of sphere impact for damage to initiate. Starphire{reg_sign} soda-lime silicate glass was second best, then Resistan{trademark}-G1 glass ceramic, and then BOROFLOAT{reg_sign} borosilicate glass. (2) Glass-ceramic Resistan{trademark}-L also required the largest force to initiate ring crack from quasi-static indentation. That ranking was followed, in descending order, by Starphire{reg_sign} soda-lime silicate glass, Resistan{trademark}-G1 glass ceramic, and BOROFLOAT{reg_sign} borosilicate glass. (3) Spheres with a lower elastic modulus require less force to initiate fracture in Resistan{trademark}-G1 from quasi-static spherical indentation. This indicates that friction is affecting ring crack initiation in Resistan{trademark}-G1. Friction also affected ring crack initiation in Starphire{reg_sign} soda-lime silicate and BOROFLOAT{reg_sign} borosilicate glasses. Among these three materials, friction was the most pronounced (largest slope in the RCIF-elastic modulus graph) in the Starphire{reg_sign} and least pronounced in the BOROFLOAT{reg_sign}. The reason for this is not understood, but differences in deformation behavior under high contact stresses could be a cause or contributor to this. (4) The force necessary to initiate contact-induced fracture is higher under dynamic conditions than it is under quasi-static conditions in Resistan{trademark}-L and Resistan{trademark}-G1 glass ceramics. This is a trend observed too in Starphire{reg_sign} and BOROFLOAT{reg_sign}. (5) There is a subtle indication there was intra-tile differences in spherical indentation-induced ring crack initiation forces. This is not a material property nor is it exclusive to glass-ceramic Resistan{trademark}-G1 glass ceramic, rather, it is a statistical mechanical response to an accumulated history of processing and handling of that specific tile.

  7. Americium/curium extraction from a lanthanide borosilicate glass

    SciTech Connect (OSTI)

    Rudisill, T.S.; Pareizs, J.M.; Ramsey, W.G.

    1996-12-01T23:59:59.000Z

    A solution containing kilogram quantities of highly radioactive isotopes of americium and curium (Am/Cm) and lanthanide fission products is currently stored in a process tank at the Department of Energy`s Savannah River Site (SRS). This tank and its vital support systems are old, subject to deterioration, and prone to possible leakage. For this reason, a program has been initiated to stabilize this material as a lanthanide borosilicate (LBS) glass. The Am/Cm has commercial value and is desired for use by the heavy isotope programs at the Oak Ridge National Laboratory (ORNL). A recovery flowsheet was demonstrated using a curium containing glass to extract the Am/Cm from the glass matrix. The procedure involved grinding the glass to less than 200 mesh and dissolving in concentrated nitric acid at 110 {degrees}C. Under these conditions, the dissolution was essentially 100% after 2 hours except for the insoluble silicon. Using a nonradioactive surrogate, the expected glass dissolution rate during Am/Cm recovery was bracketed by using both static and agitated conditions. The measured rates, 0.0082 and 0.040 g/hr.sq cm, were used to develop a predictive model for the time required to dissolve a spherical glass particle in terms of the glass density, particle size, and measured rate. The calculated dissolution time was in agreement with the experimental observation that the curium glass dissolution was complete in less than 2 hrs.

  8. Thermodynamics and Universality for Mean Field Quantum Spin Glasses

    E-Print Network [OSTI]

    Nick Crawford

    2006-10-13T23:59:59.000Z

    We study aspects of the thermodynamics of quantum versions of spin glasses. By means of the Lie-Trotter formula for exponential sums of operators, we adapt methods used to analyze classical spin glass models to answer analogous questions about quantum models.

  9. production under ionizing radiation in aluminoborosilicate glasses by EPR spectroscopy.

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 Ti3+ production under ionizing radiation in aluminoborosilicate glasses by EPR spectroscopy. P irradiation of Ti4+ ions in aluminoborosilicate glasses have been studied by EPR spectroscopy at 20 K of the Ti3+ ion EPR spectra has shown three different Ti3+ environment attributed to one [VI] Ti3+ and two

  10. Assessment, development, and testing of glass for blast environments.

    SciTech Connect (OSTI)

    Glass, Sarah Jill

    2003-06-01T23:59:59.000Z

    Glass can have lethal effects including fatalities and injuries when it breaks and then flies through the air under blast loading (''the glass problem''). One goal of this program was to assess the glass problem and solutions being pursued to mitigate it. One solution to the problem is the development of new glass technology that allows the strength and fragmentation to be controlled or selected depending on the blast performance specifications. For example the glass could be weak and fail, or it could be strong and survive, but it must perform reliably. Also, once it fails it should produce fragments of a controlled size. Under certain circumstances it may be beneficial to have very small fragments, in others it may be beneficial to have large fragments that stay together. The second goal of this program was to evaluate the performance (strength, reliability, and fragmentation) of Engineered Stress Profile (ESP) glass under different loading conditions. These included pseudo-static strength and pressure tests and free-field blast tests. The ultimate goal was to provide engineers and architects with a glass whose behavior under blast loading is less lethal. A near-term benefit is a new approach for improving the reliability of glass and modifying its fracture behavior.

  11. Non-photorealistic Rendering of Images as Evolutionary Stained Glass

    E-Print Network [OSTI]

    Ashlock, Dan

    Non-photorealistic Rendering of Images as Evolutionary Stained Glass Daniel Ashlock Mathematics-photorealistic rendering is a broad class of tech- niques for creating art from digital pictures. One or more digital to that in the tile. Tile boundaries are rendered black, providing the "lead" enclosing the stained glass panes

  12. Heterogeneous cavitation in liquid helium 4 near a glass plate

    E-Print Network [OSTI]

    Caupin, Frédéric

    Heterogeneous cavitation in liquid helium 4 near a glass plate X. Chavanne, S. Balibar and F wave to study cavitation, i.e. the nucleation of bubbles, in liquid helium 4 near a clean glass plate and threshold pressures in the range 0 to -3 bar, significantly less negative than for homogeneous cavitation

  13. Department of Electrical Engineering Spring 2011 Glass Block Solar Collector

    E-Print Network [OSTI]

    Demirel, Melik C.

    to the sponsor. The collector incorporated a solar panel that charged a battery unit. The battery poweredPENNSTATE Department of Electrical Engineering Spring 2011 Glass Block Solar Collector Overview Pittsburgh Corning, a leading manufacturer of architectural glass blocks, wanted to incorporate a solar

  14. Integrated Disposal Facility FY 2012 Glass Testing Summary Report

    SciTech Connect (OSTI)

    Pierce, Eric M.; Kerisit, Sebastien N.; Krogstad, Eirik J.; Burton, Sarah D.; Bjornstad, Bruce N.; Freedman, Vicky L.; Cantrell, Kirk J.; Snyder, Michelle MV; Crum, Jarrod V.; Westsik, Joseph H.

    2013-03-29T23:59:59.000Z

    PNNL is conducting work to provide the technical basis for estimating radionuclide release from the engineered portion of the disposal facility for Hanford immobilized low-activity waste (ILAW). Before the ILAW can be disposed, DOE must conduct a performance assessment (PA) for the Integrated Disposal Facility (IDF) that describes the long-term impacts of the disposal facility on public health and environmental resources. As part of the ILAW glass testing program, PNNL is implementing a strategy, consisting of experimentation and modeling, to provide the technical basis for estimating radionuclide release from the glass waste form in support of future IDF PAs. Key activities in FY12 include upgrading the STOMP/eSTOMP codes to do near-field modeling, geochemical modeling of PCT tests to determine the reaction network to be used in the STOMP codes, conducting PUF tests on selected glasses to simulate and accelerate glass weathering, developing a Monte Carlo simulation tool to predict the characteristics of the weathered glass reaction layer as a function of glass composition, and characterizing glasses and soil samples exhumed from an 8-year lysimeter test. The purpose of this report is to summarize the progress made in fiscal year (FY) 2012 and the first quarter of FY 2013 toward implementing the strategy with the goal of developing an understanding of the long-term corrosion behavior of LAW glasses.

  15. Widening the Axion Window via Kinetic and St\\"uckelberg Mixings

    E-Print Network [OSTI]

    Shiu, Gary; Ye, Fang

    2015-01-01T23:59:59.000Z

    We point out that kinetic and St\\"uckelberg mixings that are generically present in the low energy effective action of axions can significantly widen the window of axion decay constants. We show that an effective super-Planckian decay constant can be obtained even when the axion kinetic matrix has only sub-Planckian entries. Our minimal model involves only two axions, a St\\"uckelberg U(1) and a modest rank instanton generating non-Abelian group. Below the mass of the St\\"uckelberg U(1), there is only a single axion with a non-perturbatively generated potential. In contrast to previous approaches, the enhancement of the axion decay constant is not tied to the number of degrees of freedom introduced. We also discuss how kinetic mixings can lower the decay constant to the desired axion dark matter window. String theory embeddings of this scenario and their phenomenological features are briefly discussed.

  16. THE PLASMA WINDOW: A WINDOWLESS HIGH PRESSURE VACUUM INTERFACE FOR VARIOUS ACCELERATOR APPLICATIONS.

    SciTech Connect (OSTI)

    HERSHCOVITCH,A.I.; JOHNSON,E.D.; LANZA,R.C.

    1999-03-29T23:59:59.000Z

    The Plasma Window is a stabilized plasma arc used as an interface between accelerator vacuum and pressurized targets. There is no solid material introduced into the beam and thus it is also capable of transmitting particle beams and electromagnetic radiation with low loss and of sustaining high beam currents without damage. Measurements on a prototype system with a 3 mm diameter opening have shown that pressure differences of more than 2.5 atmospheres can be sustained with an input pressure of {approx} 10{sup -6} Torr. The system is capable of scaling to higher-pressure differences and larger apertures. Various plasma window applications for synchrotron light sources, high power lasers, internal targets, high current accelerators such as the HAWK, ATW, APT, DARHT, spallation sources, as well as for a number of commercial applications, will be discussed.

  17. Foreground Removal vs. Foreground Avoidance: Contamination of the EoR Window

    E-Print Network [OSTI]

    Chapman, Emma; Abdalla, Filipe

    2014-01-01T23:59:59.000Z

    The removal of the Galactic and extragalactic foregrounds remains a major challenge for those wishing to make a detection of the Epoch of Reionization 21-cm signal. Multiple methods of modelling these foregrounds with varying levels of assumption have been trialled and shown promising recoveries on simulated data. Recently however there has been increased discussion of using the expected shape of the foregrounds in Fourier space to define an EoR window free of foreground contamination. By carrying out analysis within this window only, one can avoid the foregrounds and any statistical bias they might introduce. In this paper we discuss the advantages and disadvantages of both foreground removal and foreground avoidance. We create a series of simulations with noise levels in line with both current and future experiments and compare the recovered statistical cosmological signal from both methods. We also relax the assumption that the foregrounds are smooth by introducing a Gaussian random factor along the line-o...

  18. Renewable Electric Plant Information System user interface manual: Paradox 7 Runtime for Windows

    SciTech Connect (OSTI)

    NONE

    1996-11-01T23:59:59.000Z

    The Renewable Electric Plant Information System (REPiS) is a comprehensive database with detailed information on grid-connected renewable electric plants in the US. The current version, REPiS3 beta, was developed in Paradox for Windows. The user interface (UI) was developed to facilitate easy access to information in the database, without the need to have, or know how to use, Paradox for Windows. The UI is designed to provide quick responses to commonly requested sorts of the database. A quick perusal of this manual will familiarize one with the functions of the UI and will make use of the system easier. There are six parts to this manual: (1) Quick Start: Instructions for Users Familiar with Database Applications; (2) Getting Started: The Installation Process; (3) Choosing the Appropriate Report; (4) Using the User Interface; (5) Troubleshooting; (6) Appendices A and B.

  19. Analysis of tritium extraction from liquid lithium by permeation window and solid gettering processes

    SciTech Connect (OSTI)

    Takeda, T. [Japan Atomic Energy Research Inst., Ibaraki-ken (Japan); Ying, A.Y.; Abdou, M.A. [Univ. of California, Los Angeles, CA (United States)

    1994-12-31T23:59:59.000Z

    Tritium recovery from liquid lithium at low concentration is an important problem for liquid metal breeder-blanket in a fusion reactor. Previous studies have identified tritium recovery methods including molten salt extraction, gettering recovery, permeation window, and vacuum distillation. In this paper, the authors focus on the numerical studies on tritium extraction by permeation window and gettering processes. These studies include for example: dynamic tritium concentration variation along the flow direction, tritium inventory distributions in the permeator and getter bed, along with the effect of dispersion on extraction efficiency. Using a model description makes it possible to determine functional dependence and provide insight into the interrelationships of the various operating conditions and material properties which may affect the behavior of tritium in the material. Clearly, reliable material properties (such as diffusivity, solubility, etc.) are essential for realistic evaluations.

  20. Property Data for Simulated Americium/Curium Glasses

    SciTech Connect (OSTI)

    Riley, B.J.; Smith, D.E.; Peeler, D.K.; Reamer, I.A.; Vienna, J.D.; Schweiger, M.J.

    1999-10-20T23:59:59.000Z

    The authors studied the properties of mixed lanthanide-alumino-borosilicate glasses. Fifty-five glasses were designed to augment a previous, Phase I, study by systematically varying the composition of Ln{sub 2}O{sub 3} and the concentrations of Ln{sub 2}O{sub 3}, SiO{sub 2}, B{sub 2}O{sub 3}, Al{sub 2}O{sub 3}, and SrO in glass. These glasses were designed and fabricated at the Savannah River Technology Center and tested at the Pacific Northwest National Laboratory. The properties measured include the high-temperature viscosity ({eta}) as a function of temperature (T) and the liquidus temperature (T{sub L}) of Phase II test glasses.