Powered by Deep Web Technologies
Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Variable-delay feedback control of unstable steady states in retarded time-delayed systems  

E-Print Network (OSTI)

We study the stability of unstable steady states in scalar retarded time-delayed systems subjected to a variable-delay feedback control. The important aspect of such a control problem is that time-delayed systems are already infinite-dimensional before the delayed feedback control is turned on. When the frequency of the modulation is large compared to the system's dynamics, the analytic approach consists of relating the stability properties of the resulting variable-delay system with those of an analogous distributed delay system. Otherwise, the stability domains are obtained by a numerical integration of the linearized variable-delay system. The analysis shows that the control domains are significantly larger than those in the usual time-delayed feedback control, and that the complexity of the domain structure depends on the form and the frequency of the delay modulation.

Aleksandar Gjurchinovski; Viktor Urumov

2010-07-06T23:59:59.000Z

2

Impact of retarded spark timing on engine combustion, hydrocarbon emissions, and fast catalyst light-off  

E-Print Network (OSTI)

An experimental study was performed to determine the effects of substantial spark retard on engine combustion, hydrocarbon (HC) emissions, feed gas enthalpy, and catalyst light-off. Engine experiments were conducted at ...

Hallgren, Brian E. (Brian Eric), 1976-

2005-01-01T23:59:59.000Z

3

Mental retardation, hereditary?  

NLE Websites -- All DOE Office Websites (Extended Search)

Mental retardation, hereditary? Mental retardation, hereditary? Name: Karthikk Status: N/A Age: N/A Location: N/A Country: N/A Date: N/A Question: If a mentally retarded couple had a child, would it be mentally retarded? Replies: Karthikk, Just a short answer. The likelihood you ask about would vary according to what type of mental retardation is present in each of the parents. Some (probably most) forms of mental retardation are genetic in nature and therefore would be inheritable. There are of course cases where non-mentally retarded parents produce a child which is mentally retarded. These cases occur through errors in either production of the sex cells, possibly due to exposure to radiation, for example, or in errors in cell division leading up to and through conception. A good deal of research is currently underway mapping the human chromosomes. I would suspect in the not-so-distant future, an exact answer could be given to your question by looking at the chromosomes of the parents and producing at least a statistical prediction of heritable mental retardation.

4

Effects of the Sun's time-retarded gravitational field on the orbital motions of Mercury and Halley's Comet  

E-Print Network (OSTI)

The neoclassical causal version for Newton's acausal gravitational theory explains exactly the anomalous speed-changes observed for six Earth flybys and an anomalous lunar orbital speed-change (arXiv:1105.3857v10). This article estimates the effects of the neoclassical causal theory on the orbital motions of two objects revolving around the Sun, Mercury and Halley's Comet. The change in the period for Mercury is predicted to be about +1.86 ms per year, and the predicted change in the angle for perihelion is -0.032 arc seconds per century, for which the magnitude is negligible compared with the relativistic advance of +43 arc seconds per century. The period for Halley's Comet, 75.3 years, is predicted to decrease by about 10 minutes. Therefore, the neoclassical causal theory does not conflict with general relativity theory, and it is not the cause for a delay of one or two weeks in the return time of Halley's Comet.

J. C. Hafele

2011-11-28T23:59:59.000Z

5

Novel additives to retard permeable flow  

Science Conference Proceedings (OSTI)

Low concentrations of surfactant and cosolute in water, can selectively retard permeable flow in high permeability rocks compared to low permeability ones. This represents a way forward for more efficient areal sweep efficiency when water flooding a reservoir during improved oil recovery. (author)

Golombok, Michael [Shell Exploration and Production, Kessler Park 1, 2288 GS Rijswijk (Netherlands); Department of Mechanical Engineering, Technische Universiteit Eindhoven, 5600 MB Eindhoven (Netherlands); Crane, Carel; Ineke, Erik; Welling, Marco [Shell Exploration and Production, Kessler Park 1, 2288 GS Rijswijk (Netherlands); Harris, Jon [Shell Exploration and Production, Kessler Park 1, 2288 GS Rijswijk (Netherlands); Shell UK Ltd., North Anderson Drive, Aberdeen, AB15 6BL (United Kingdom)

2008-09-15T23:59:59.000Z

6

Quantum mechanics of time travel through post-selected teleportation  

E-Print Network (OSTI)

This paper discusses the quantum mechanics of closed-timelike curves (CTCs) and of other potential methods for time travel. We analyze a specific proposal for such quantum time travel, the quantum description of CTCs based ...

Maccone, Lorenzo

7

Supplier selection and performance evaluation in just-in-time production environments  

Science Conference Proceedings (OSTI)

The purpose of this paper is to aid just-in-time (JIT) manufacturers in selecting the most appropriate suppliers and in evaluating supplier performance. Many manufacturers employ the JIT philosophy in order to be more competitive in today's global market. ... Keywords: Just-in-time production, Neural network, Supplier performance evaluation, Supplier selection

Asl? Aksoy; Nursel Öztürk

2011-05-01T23:59:59.000Z

8

Energy Aware Dynamic Voltage and Frequency Selection for Real-Time Systems with Energy Harvesting  

E-Print Network (OSTI)

Energy Aware Dynamic Voltage and Frequency Selection for Real-Time Systems with Energy Harvesting}@binghamton.edu Abstract In this paper, an energy aware dynamic voltage and frequency selection (EA-DVFS) algorithm energy and the harvested energy in a future duration. Specifically, if the system has sufficient energy

Qiu, Qinru

9

Real-time timbral organisation: Selecting samples based upon similarity1  

Science Conference Proceedings (OSTI)

A comparison is made between two systems of real-time sample selection using timbral proximity that has relevance for live performance. Sound files in large sample libraries are analysed for audio features (amplitude RMS, spectral centroid, spectral ...

Arne Eigenfeldt; Philippe Pasquier

2010-08-01T23:59:59.000Z

10

Polyolefin-based flame retardant material  

Disclosure Number 200902239 Technology Summary ... Invention discloses a method to produce flame retardant fibers from neat and recycled ...

11

Environmentally Benign Flame Retardant Nanocoatings for Fabric  

E-Print Network (OSTI)

A variety of materials were used to fabricate nanocoatings using layer-by-layer (LbL) assembly to reduce the flammability of cotton fabric. The most effective brominated flame retardants have raised concerns related to their toxicity and environmental impact, which has created a need for alternative flame retardant chemistries and approaches. Polymer nanocomposites typically exhibit reduced mass loss and heat release rates, along with anti-dripping behavior, all of which are believed to be due to the formation of a barrier surface layer. Despite these benefits, the viscosity and modulus of the final polymeric material is often altered, making industrial processing difficult. These challenges inspired the use of LbL assembly to create densely layered nanocomposites in an effort to produce more flame-retardant coatings. Laponite and montmorillonite (MMT) clay were paired with branched poly(ethylenimine) to create thin film assemblies that can be tailored by changing pH and concentration of aqueous deposition mixtures. Both films can be grown linearly as a function of layers deposited, and they contained at least 70 wt percent of clay. When applying these films to cotton fabric, the individual fibers are uniformly coated and the fabric has significant char left after burning. MMT-coated fabric exhibits reduced total heat release, suggesting a protective ceramic surface layer is created. Small molecule, POSS-based LbL thin films were also successfully deposited on cotton fabric. With less than 8 wt percent added to the total fabric weight, more than 12 wt percent char remained after microscale combustion calorimetry. Furthermore, afterglow time was reduced and the fabric weave structure and shape of the individual fibers were highly preserved following vertical flame testing. A silica-like sheath was formed after burning that protected the fibers. Finally, the first intumescent LbL assembly was deposited on cotton fabric. SEM images show significant bubble formation on fibers, coated with a 0.5 wt percent PAAm/1 wt percent PSP coating after burning. In several instances, a direct flame on the fabric was extinguished. The peak HRR and THR of coated fabric has 30 percent and 65 percent reduction, respectively, compared to the uncoated control fabric. These anti-flammable nanocoatings provide a relatively environmentally-friendly alternative for protecting fabrics, such as cotton, and lay the groundwork for rendering many other complex substrates (e.g., foam) flame-retardant without altering their processing and desirable mechanical behavior.

Li, Yu-Chin

2011-05-01T23:59:59.000Z

12

A Real-Time Database QoS-aware Service Selection Protocol for MANET  

E-Print Network (OSTI)

The real-time database service selection depends typically to the system stability in order to handle the time-constrained transactions within their deadline. However, applying the real-time database system in the mobile ad hoc networks requires considering the mobile nodes limited capacities. In this paper, we propose cross-layer service selection which combines performance metrics measured in the real-time database system to those used by the routing protocol in order to make the best selection decision. It ensures both timeliness and energy efficiency by avoiding low-power and busy service provider node. A multicast packet is used in order to reduce the transmission cost and network load when sending the same packet to multiple service providers. In this paper, we evaluate the performance of our proposed protocol. Simulation results, using the Network Simulator NS2, improve that the protocol decreases the deadline miss ratio of packets, increases the service availability and reduces the service response ti...

Rekik, Jihen Drira; Ghezala, Henda Ben

2011-01-01T23:59:59.000Z

13

Sept. 2009 Fire Retardants Workshop Agenda and ...  

Science Conference Proceedings (OSTI)

... The role of NIOSH in protecting the on-the-job health of fire ... Life Cycle Analysis of Fire Retardants, Dr. Margaret Simonson McNamee, Research ...

2011-11-16T23:59:59.000Z

14

Halogen Free Flame Retardant for ABS Composite with Oxides ...  

Science Conference Proceedings (OSTI)

The irrevocable finality from flame retardant is fires protection to help safeguard of ... the oxides particles on obtain the ABS with halogen free flame retardant.

15

String deformations induced by retardation effects  

E-Print Network (OSTI)

The rotating string model is an effective model of mesons, in which the quark and the antiquark are linked by a straight string. We previously developed a new framework to include the retardation effects in the rotating string model, but the string was still kept straight. We now go a step further and show that the retardation effects cause a small deviation of the string from the straight line. We first give general arguments constraining the string shape. Then, we find analytical and numerical solutions for the string deformation induced by retardation effects. We finally discuss the influence of the curved string on the energy spectrum of the model.

F. Buisseret; V. Mathieu; C. Semay

2006-05-30T23:59:59.000Z

16

Plant Support Engineering: Utility Selective Leaching One-Time Inspection Needs  

Science Conference Proceedings (OSTI)

The selective leaching process involves the preferential removal of one of the alloying elements from an alloy material, resulting in a significant reduction in material strength. The most common examples are dezincification (the selective removal of zinc from brass alloys) and graphitization (the selective removal of iron from cast iron). Because selective leaching generally does not result in a change in the dimensions of a component and may occur without visible signs, it can be difficult to detect.

2007-12-18T23:59:59.000Z

17

On The Toxicity of Flame Retardants in Buildings and What Can Be Done About  

NLE Websites -- All DOE Office Websites (Extended Search)

On The Toxicity of Flame Retardants in Buildings and What Can Be Done About On The Toxicity of Flame Retardants in Buildings and What Can Be Done About It Speaker(s): Arlene Blum Date: November 3, 2010 - 12:00pm Location: 90-3122 Seminar Host/Point of Contact: William Fisk Polystyrene, polyisocyanurate, and polyurethane are insulation materials that increase energy efficiency and whose use in buildings, especially energy efficient buildings, is growing rapidly. At the same time, the flame retardants currently in use with these materials are often chemicals that are known to be toxic or have not been adequately evaluated for their impact on human health and the environment. For example, all polystyrene foam insulation used in buildings is treated with HBCD, a persistent, bioaccumulative, and toxic flame retardant. The impacts of exposure to

18

Site selectivity in the reaction of Si(111)-(7 times 7) with Si sub 2 H sub 6  

SciTech Connect

We find that the reaction of disilane with the Si(111)-(7{times}7) surface shows strong site selectivity. The reaction involves the fission of the Si-Si bond of Si{sub 2}H{sub 6} even at low temperatures and occurs preferentially at rest-atom sites of the 7{times}7 surface. The reaction of the products of the thermal dissociation of the surface-bound SiH{sub x} groups with surface dangling-bond sites is also site selective. We propose mechanisms to explain the above observations.

Avouris, Ph.; Bozso, F. (T. J. Watson Research Center, Yorktown Heights, NY (USA))

1990-03-22T23:59:59.000Z

19

Energy aware dynamic voltage and frequency selection for real-time systems with energy harvesting  

Science Conference Proceedings (OSTI)

In this paper, an energy aware dynamic voltage and frequency selection (EA-DVFS) algorithm is proposed. The EA-DVFS algorithm adjusts the processor's behavior depending on the summation of the stored energy and the harvested energy in a future duration. ...

Shaobo Liu; Qinru Qiu; Qing Wu

2008-03-01T23:59:59.000Z

20

Off-line test selection with test purposes for non-deterministic timed automata  

Science Conference Proceedings (OSTI)

This paper proposes novel off-line test generation techniques for non-deterministic timed automata with inputs and outputs (TAIOs) in the formal framework of the tioco conformance theory. In this context, a first problem is the determinization of TAIOs, ... Keywords: approximate determinization, conformance testing, game, partial observability, test purpose, timed automata, urgency

Nathalie Bertrand; Thierry Jéron; Amélie Stainer; Moez Krichen

2011-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Spacetime nonlocality and retardation in relativistic heavy-ion collisions  

SciTech Connect

We discuss the exact numerical solution of the classical relativistic equations of motion for a Lagrangian corresponding to point nucleons interacting with massive scalar and vector meson fields. The equations of motion contain both external retarded Lorentz forces and radiation-reaction forces; the latter involve nonlocal terms that depend upon the past history of the nucleon in addition to terms analogous to those of classical electrodynamics. The resulting microscopic many-body approach to relativistic heavy-ion collisions is manifestly Lorentz covariant and allows for nonequilibrium phenomena, interactions with correlated clusters of nucleons, and particle production. For point nucleons, the asymptotic behavior of nucleonic motion prior to the collision is exponential, with a range in proper time of approximately 0.5 fm. However, this behavior is altered by the finite nucleon size, whose effect we are currently incorporating into our equations of motion. The spacetime nonlocality and retardation that will be present in the solutions of these equations may be responsible for significant collective effects in relativstic heavy-ion collisions. 11 refs., 3 figs.

Bush, B.W.; Nix, J.R.; Sierk, A.J.

1991-01-01T23:59:59.000Z

22

Discrete-Time Block Models for Transmission Line Channels: Static and Doubly Selective Cases  

E-Print Network (OSTI)

Most methodologies for modeling Transmission Line (TL) based channels define the input-output relationship in the frequency domain (FD) and handle the TL resorting to a two-port network (2PN) formalism. These techniques have not yet been formally mapped into a discrete-time (DT) block model, which is useful to simulate and estimate the channel response as well as to design optimal precoding strategies. TL methods also fall short when they are applied to Time Varying (TV) systems, such as the power line channel. The objective of this paper is to establish if and how one can introduce a DT block model for the Power Line Channel. We prove that it is possible to use Lifting and Trailing Zeros (L&TZ) techniques to derive a DT block model that maps the TL-based input-output description directly in the time domain (TD) block channel model. More specifically, we find an interesting relationship between the elements of an ABCD matrix, defined in the FD, and filtering kernels that allow an elegant representation of...

Galli, Stefano

2011-01-01T23:59:59.000Z

23

CITRIC ACID AS A SET RETARDER FOR CALCIUM ALUMINATE PHOSPHATE CEMENTS.  

DOE Green Energy (OSTI)

Citric acid added as set retarder significantly contributed to enhancing the setting temperature and to extending the thickening time of a calcium aluminate phosphate (CaP) geothermal cement slurry consisting of calcium aluminate cement (CAC) as the base reactant and sodium polyphosphate (NaP) solution as the acid reactant. The set-retarding activity of citric acid was due to the uptake of Ca{sup 2+} ions from the CAC by carboxylic acid groups within the citric acid. This uptake led to the precipitation of a Ca-complexed carboxylate compound as a set-retarding barrier layer on the CAC grains' surfaces. However, this barrier layer was vulnerable to disintegration by the attack of free Ca{sup 2+} ions from CAC, and also to degradation at elevated temperature, thereby promoting the generation of exothermic energy from acid-base reactions between the CAC and NaP after the barrier was broken. The exothermic reaction energy that was promoted in this way minimized the loss in strength of the citric acid-retarded cement. The phase composition assembled in both retarded and non-retarded cements after autoclaving at 180 C encompassed three reaction products, hydroxyapatite (HOAp), hydrogrossular and boehmite, which are responsible for strengthening the autoclaved cement. The first two reaction products were susceptible to reactions with sulfuric acid and sodium sulfate to form crystalline bassanite scale as the corrosion product. The boehmite phase possessed a great resistance to acid and sulfate. Although the bassanite scales clinging to the cement's surfaces were the major factor governing the loss in weight, they served in protecting the cement from further acid- and sulfate-corrosion until their spallation eventually occurred. Nevertheless, the repetitive processes of HOAp and hydrogrossular {yields} bassanite {yields} spallation played an important role in extending the useful lifetime of CaP cement in a low pH environment at 180 C.

SUGAMA,T.; BROTHERS, L.E.

2005-01-01T23:59:59.000Z

24

Fire Retardants and their Potential Impact on Fire Fighter ...  

Science Conference Proceedings (OSTI)

... containing products currently (and for the foreseeable future) in homes where fires ... Risk-based analysis of the value of fire retardant chemicals; A ...

2011-11-16T23:59:59.000Z

25

Development and testing of flame retardant additives and polymers.  

E-Print Network (OSTI)

??The first chapter examines the non-halogenated flame retardant additives. The synthesis and blending of these various boron compounds are discussed and the blending of these… (more)

Jurs, Joshua Lewis

2004-01-01T23:59:59.000Z

26

Real Time Selective Harmonic Minimization for Multilevel Inverters Connected to Solar Panels Using Artificial Neural Network Angle Generation  

SciTech Connect

This work approximates the selective harmonic elimination problem using artificial neural networks (ANNs) to generate the switching angles in an 11-level full-bridge cascade inverter powered by five varying dc input sources. Each of the five full bridges of the cascade inverter was connected to a separate 195-W solar panel. The angles were chosen such that the fundamental was kept constant and the low-order harmonics were minimized or eliminated. A nondeterministic method is used to solve the system for the angles and to obtain the data set for the ANN training. The method also provides a set of acceptable solutions in the space where solutions do not exist by analytical methods. The trained ANN is a suitable tool that brings a small generalization effect on the angles' precision and is able to perform in real time (50-/60-Hz time window).

Tolbert, Leon M [ORNL; Ozpineci, Burak [ORNL; Filho, Faete [ORNL; Cao, Yue [ORNL

2011-01-01T23:59:59.000Z

27

Corporate Social Responsibility Practices and Financial Performance over Time for Selected U.S. Corporations  

E-Print Network (OSTI)

Corporate social responsibility (CSR) is a subject long debated since the 1930s, but the premises of the topic in regards to the what, how, why, and to whom it should be remain in question. The relation between CSR and corporate financial performance (CFP) has emerged at the forefront of this debate, particularly within the last 30 years, yet no unified theory has been reached. Other scholars interested in CSR have criticized the emphasis on CFP as a means of economic justification for what they believe to be a broader social issue, and have attempted to redirect the focus in CSR research to include other motivations and outcomes associated with organizational stakeholders other than shareholders. Using a descriptive and instrumental stakeholder theory approach, the focus of the current study was to explore CSR practices in both a dependent and independent sense. These theoretical underpinnings reflect stakeholder management decisions based on organizational characteristics, and the strategic management of various organizational stakeholders, respectively. The study population consisted of a diverse array of 353 U.S.- based corporations, 80 percent from the Fortune 500. Data included eleven corporate classification variables that represented organizations’ geographical location, industry, executive leadership dimensions, and financial health. It also included six CFP variables that represented accounting and market-based measures, and seven CSR variables that represented the key organizational stakeholders of the local community and environment, employees, and customers. The corporate classification variables were utilized to assess CSR performances, while CFP was assessed by analyzing differences among levels of the CSR practices. These assessments were performed for organizations for the twelve years within 1991-2002. Several results that assisted in informing descriptive and instrumental stakeholder theory were produced through the examination of previously used and under-explored variables. Specifically, the study results included new insights regarding how several organizational characteristics related to their CSR practices. Study findings provided elaboration regarding how performance differences in seven key CSR categories affected six representative accounting and market-based measures of corporate financial performance. Implications for practice for organizational decision-makers are provided along with detailed information pertaining to how, with inferences as to why, firms engage in CSR. Additionally, associated financial outcomes from different levels of CSR implementation are reported. Key findings from the study were that the CSR practices regarding employees and the environment remained stable over the twelve-year time period. Additionally, organizations’ geographical location, financial health, and corporate leadership dimensions had an impact on CSR practices for various stakeholder groups, with the exception of employees. A high level of investment in CSR for certain stakeholder groups did not produce the best financial outcomes in all cases; however, organizations that emphasized CSR in the categories relative to the community and its employees outperformed others with respect to certain financial performance measures.

Phelan Ribera, Kelli Catherine

2010-08-01T23:59:59.000Z

28

Carbohydrate derivedpseudolignin can retard cellulose biological conversion  

NLE Websites -- All DOE Office Websites (Extended Search)

Carbohydrate Carbohydrate Derived-Pseudo-Lignin Can Retard Cellulose Biological Conversion Rajeev Kumar, 1,2,3 Fan Hu, 3,4 Poulomi Sannigrahi, 3,4 Seokwon Jung, 3,4 Arthur J. Ragauskas, 3,4 Charles E. Wyman 1,2,3 1 Center for Environmental Research and Technology, Bourns College of Engineering, 1084 Columbia Avenue, Riverside, California 92507; telephone: 951-781-5668; fax: 951-781-5790; e-mail: rajeev.dartmouth@gmail.com 2 Department of Chemical and Environmental Engineering, Bourns College of Engineering, 446 Winston Chung Hall, 900 University Avenue, Riverside, California 92507 3 BioEnergy Science Center (BESC), Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831-6422 4 School of Chemistry and Biochemistry, Georgia Institute of Technology, Atlanta, Georgia ABSTRACT: Dilute acid as well as water only (hydrother- mal) pretreatments often lead to a significant

29

HLYWD: a program for post-processing data files to generate selected plots or time-lapse graphics  

SciTech Connect

The program HLYWD is a post-processor of output files generated by large plasma simulation computations or of data files containing a time sequence of plasma diagnostics. It is intended to be used in a production mode for either type of application; i.e., it allows one to generate along with the graphics sequence, segments containing title, credits to those who performed the work, text to describe the graphics, and acknowledgement of funding agency. The current version is designed to generate 3D plots and allows one to select type of display (linear or semi-log scales), choice of normalization of function values for display purposes, viewing perspective, and an option to allow continuous rotations of surfaces. This program was developed with the intention of being relatively easy to use, reasonably flexible, and requiring a minimum investment of the user's time. It uses the TV80 library of graphics software and ORDERLIB system software on the CDC 7600 at the National Magnetic Fusion Energy Computing Center at Lawrence Livermore Laboratory in California.

Munro, J.K. Jr.

1980-05-01T23:59:59.000Z

30

The view-selection problem has an exponential-time lower bound for conjunctive queries and views  

Science Conference Proceedings (OSTI)

The view-selection problem is to design and materialize a set of views over a database schema, such that the choice of views minimizes the cost of evaluating the selected workload of queries, and the combined size of the materialized views does not exceed ...

Rada Chirkova

2002-06-01T23:59:59.000Z

31

Extracting Unique Information from High-Resolution Forecast Models: Monitoring Selected Fields and Phenomena Every Time Step  

Science Conference Proceedings (OSTI)

A new strategy for generating and presenting model diagnostic fields from convection-allowing forecast models is introduced. The fields are produced by computing temporal-maximum values for selected diagnostics at each horizontal grid point ...

John S. Kain; Scott R. Dembek; Steven J. Weiss; Jonathan L. Case; Jason J. Levit; Ryan A. Sobash

2010-10-01T23:59:59.000Z

32

A MULTIPLE-ITEM MULTIPLE-CONSTRAINT INVENTORY OPTIMIZATION AND SUPPLIER SELECTION MODEL UNDER LEAD TIME DEMAND UNCERTAINTY.  

E-Print Network (OSTI)

??The objective of this thesis is to solve a multiple-item, one-retailer inventory control and supplier selection problem with multiple constraints and uncertainties. For each item,… (more)

Zhu, Rongjia

2009-01-01T23:59:59.000Z

33

Children's residential exposures to flame retardants, pesticides and pesticide degradation products, and the relationship of pesticides with autonomic nervous system functioning  

E-Print Network (OSTI)

diphenyl ethers: a flame-retardant additive in severaldiphenyl ether (PBDE) flame retardants. Neurotoxicology. 28,diphenyl ethers: a flame-retardant additive in several

Quiros Alcala, Lesliam

2010-01-01T23:59:59.000Z

34

Durable and Non-Toxic Topical Flame Retardants for Cotton and Cotton Blends.  

E-Print Network (OSTI)

??Flame retardant chemicals were used as topical finishes on cotton and cotton blended fabric. Comparison of flame resistance and durability of non-bromine/non-antimony flame retardants were… (more)

Mathews, Marc Christopher

2008-01-01T23:59:59.000Z

35

Real time selective harmonic minimization for multilevel inverters using genetic algorithm and artifical neural network angle generation  

Science Conference Proceedings (OSTI)

The work developed here proposes a methodology for calculating switching angles for varying DC sources in a multilevel cascaded H-bridges converter. In this approach the required fundamental is achieved, the lower harmonics are minimized, and the system can be implemented in real time with low memory requirements. Genetic algorithm (GA) is the stochastic search method to find the solution for the set of equations where the input voltages are the known variables and the switching angles are the unknown variables. With the dataset generated by GA, an artificial neural network (ANN) is trained to store the solutions without excessive memory storage requirements. This trained ANN then senses the voltage of each cell and produces the switching angles in order to regulate the fundamental at 120 V and eliminate or minimize the low order harmonics while operating in real time.

Filho, Faete J [ORNL; Tolbert, Leon M [ORNL; Ozpineci, Burak [ORNL

2012-01-01T23:59:59.000Z

36

A low-voltage retarding-field Mott polarimeter for photocathode characterization  

E-Print Network (OSTI)

Nuclear physics experiments at Thomas Jefferson National Accelerator Facility's CEBAF rely on high polarization electron beams. We describe a recently commissioned system for prequalifying and studying photocathodes for CEBAF with a load-locked, low-voltage polarized electron source coupled to a compact retarding-field Mott polarimeter. The polarimeter uses simplified electrode structures and operates from 5 to 30 kV. The effective Sherman function for this device has been calibrated by comparison with the CEBAF 5 MeV Mott polarimeter. For elastic scattering from a thick gold target at 20 keV, the effective Sherman function is 0.201(5). Its maximum efficiency at 20 keV, defined as the detected count rate divided by the incident particle current, is 5.4(2) x 10-4, yielding a figure-of-merit, or analyzing power squared times efficiency, of 1.0(1) x 10-5. The operating parameters of this new polarimeter design are compared to previously published data for other compact Mott polarimeters of the retarding-field type.

James L. McCarter; Marcy L. Stutzman; Kenneth W. Trantham; Tyler G. Anderson; April M. Cook; Timothy J. Gay

2010-03-29T23:59:59.000Z

37

Flame retardant finishing for cotton using a hydroxy-functional organophosphorus oligomer.  

E-Print Network (OSTI)

??New durable flame retardant finishing systems based on a hydroxy-functional organophosphorus oligomer (HFPO) and a bonding agent have been developed for cotton. In this research,… (more)

Wu, Weidong

2004-01-01T23:59:59.000Z

38

Retarded Green's Function Of A Vainshtein System And Galileon Waves  

E-Print Network (OSTI)

Motivated by the desire to test modified gravity theories exhibiting the Vainshtein mechanism, we solve in various physically relevant limits, the retarded Galileon Green's function (for the cubic theory) about a background sourced by a massive spherically symmetric static body. The static limit of our result will aid us, in a forthcoming paper, in understanding the impact of Galileon fields on the problem of motion in the solar system. In this paper, we employ this retarded Green's function to investigate the emission of Galileon radiation generated by the motion of matter lying deep within the Vainshtein radius r_v of the central object: acoustic waves vibrating on its surface, and the motion of compact bodies gravitationally bound to it. If \\lambda is the typical wavelength of the emitted radiation, and r_0 is the typical distance of the source from the central mass, with r_0 radiation rate is suppressed by the ratio (r_v/\\lambda)^{-3/2} at the monopole and dipole orders at high frequencies r_v/\\lambda >> 1. However, at high enough multipole order, the radiation rate is enhanced by powers of r_v/r_0. At low frequencies r_v/\\lambda << 1, and when the motion is non-relativistic, Galileon waves yield a comparable rate for the monopole and dipole terms, and are amplified by powers of the ratio r_v/r_0 for the higher multipoles.

Yi-Zen Chu; Mark Trodden

2012-10-24T23:59:59.000Z

39

Hybrid quadrupole mass filter/quadrupole ion trap/time-of-flight-mass spectrometer for infrared multiple photon dissociation spectroscopy of mass-selected ions  

Science Conference Proceedings (OSTI)

We present a laboratory-constructed mass spectrometer optimized for recording infrared multiple photon dissociation (IRMPD) spectra of mass-selected ions using a benchtop tunable infrared optical parametric oscillator/amplifier (OPO/A). The instrument is equipped with two ionization sources, an electrospray ionization source, as well as an electron ionization source for troubleshooting. This hybrid mass spectrometer is composed of a quadrupole mass filter for mass selection, a reduced pressure ({approx}10{sup -5} Torr) quadrupole ion trap (QIT) for OPO irradiation, and a reflectron time-of-flight drift tube for detecting the remaining precursor and photofragment ions. A helium gas pulse is introduced into the QIT to temporarily increase the pressure and hence enhance the trapping efficiency of axially injected ions. After a brief pump-down delay, the compact ion cloud is subjected to the focused output from the continuous wave OPO. In a recent study, we implemented this setup in the study of protonated tryptophan, TrpH{sup +}, as well as collision-induced dissociation products of this protonated amino acid [W. K. Mino, Jr., K. Gulyuz, D. Wang, C. N. Stedwell, and N. C. Polfer, J. Phys. Chem. Lett. 2, 299 (2011)]. Here, we give a more detailed account on the figures of merit of such IRMPD experiments. The appreciable photodissociation yields in these measurements demonstrate that IRMPD spectroscopy of covalently bound ions can be routinely carried out using benchtop OPO setups.

Gulyuz, Kerim; Stedwell, Corey N.; Wang Da; Polfer, Nick C. [Department of Chemistry, University of Florida, P.O. Box 117200, Gainesville, Florida 32611 (United States)

2011-05-15T23:59:59.000Z

40

Kinetics of HEX-BCC Transition in a Triblock Copolymer in a Selective Solvent: Time Resolved Small Angle X-ray Scattering Measurements and Model Calculations  

E-Print Network (OSTI)

Time-resolved small angle x-ray scattering (SAXS) was used to examine the kinetics of the transition from HEX cylinders to BCC spheres at various temperatures in poly(styrene-b- ethylene-co-butylene-b-styrene) (SEBS) in mineral oil, a selective solvent for the middle EB block. Temperature-ramp SAXS and rheology measurements show the HEX to BCC order-order transition (OOT) at ~127 oC and order-disorder transition (ODT) at ~180 oC. We also observed the metastability limit of HEX in BCC with a spinodal temperature, Ts ~ 150 oC. The OOT exhibits 3 stages and occurs via a nucleation and growth mechanism when the final temperature Tf peak into two peaks when the cylinder spacing and modulation wavelength are incommensurate predicted by the model is confirmed by analysis of the SAXS data.

Minghai Li; Yongsheng Liu; Huifen Nie; Rama Bansil; Milos Steinhart

2007-10-24T23:59:59.000Z

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Method for producing flame retardant porous products and products produced thereby  

DOE Patents (OSTI)

A method for fire retarding porous products used for thermal energy storage and products produced thereby is provided. The method includes treating the surface of the phase change material-containing porous products with a urea fire-retarding agent. Upon exposure to a flame, the urea forms an adduct with the phase change material which will not sustain combustion (is self-extinguishing) in air. No halogens or metal oxides are contained in the fire retardant, so no potentially noxious halide smoke or fumes are emitted if the product is continuously exposed to a flame. 1 fig.

Salyer, I.O.

1998-08-04T23:59:59.000Z

42

Method for producing flame retardant porous products and products produced thereby  

DOE Green Energy (OSTI)

A method for fire retarding porous products used for thermal energy storage and products produced thereby is provided. The method includes treating the surface of the phase change material-containing porous products with a urea fire-retarding agent. Upon exposure to a flame, the urea forms an adduct with the phase change material which will not sustain combustion (is self-extinguishing) in air. No halogens or metal oxides are contained in the fire retardant, so no potentially noxious halide smoke or fumes are emitted if the product is continuously exposed to a flame.

Salyer, Ival O. (Dayton, OH)

1998-08-04T23:59:59.000Z

43

Method for Producing Flame Retardant Porous Products and Products Produced Thereby  

DOE Patents (OSTI)

A method for fire retarding porous products used for thermal energy storage and products produced thereby is provided. The method includes treating the surface of the phase change material-containing porous products with a urea fire-retarding agent. Upon exposure to a flame, the urea forms an adduct with the phase change material which will not sustain combustion (is self-extinguishing) in air. No halogens or metal oxides are contained in the fire retardant, so no potentially noxious halide smoke or fumes are emitted if the product is continuously exposed to a flame.

Salyer, Ival O. (Dayton, OH)

1998-08-04T23:59:59.000Z

44

Selected References  

Science Conference Proceedings (OSTI)

...T.C. Fowler, Value Analysis in Materials Selection and Design, Materials Selection and Design, Vol 20, ASM Handbook,

45

An In-depth Investigation of an Aluminum Chloride Retarded Mud Acid System on Sandstone Reservoirs  

E-Print Network (OSTI)

Sandstone acidizing using mud acid is a quick and complex process where dissolution and precipitation occur simultaneously. Retarded mud acids are less reactive with the rock reducing the reaction rate hence increased penetration into the formation to remove deep damage. To understand thoroughly the retarded mud acid system, an in-depth investigation of the reaction of HF (hydrofluoric) and H2SiF6 (fluorosilic acid) with alumino silicates and the retarded system is undertaken using coreflood analysis and mineralogy analysis using the inductively coupled plasma. Coreflood analysis is used to understand and investigate the permeability changes in the sandstone rock as the retarded mud acid is injected at different conditions and the inductively coupled plasma (ICP) is used to investigate the effluent samples from the coreflood analysis to properly understand this system. Several issues that have not been addressed previously in literature are identified and discussed, including an optimum flowrate when sandstone is acidized, by acidizing the sandstone rock with a retarded acid system at various flowrates and determining the initial and final permeabilities. Also investigated is the retarded acids compatibility with ferric iron and a comparison of the retarded acid system to regular acid to consequently enable a thorough understanding of the retarded mud acid system using aluminum chloride (AlRMHF). Based on the work done, it is found that the absence of a hydrochloric (HCl) preflush is very detrimental to the sandstone core as calcium fluoride is precipitated and the retarded acid system is found to be compatible with iron(III) as an impurity. The regular acid (RMHF) dissolves considerably more silicon and produces more fines than the AlRMHF. 1cc/min is found to be the optimum flowrate when a sandstone core is acidized with AlRMHF. At this low flowrate, less silicon is dissolved, more aluminum is seen in the effluent and more calcium is dissolved. The retarded aluminum acid system considerably reduces the rate of reaction as evidenced in the dissolution reaction when compared to a regular mud acid system. This reduced rate of reaction implies deeper acid penetration and ultimately deeper damage removal.

Aneto, Nnenna

2012-05-01T23:59:59.000Z

46

Building America Top Innovations Hall of Fame Profile … Vapor Retarder Classification  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2006 the IRC has permitted Class III 2006 the IRC has permitted Class III vapor retarders like latex paint (see list above) in all climate zones under certain conditions thanks to research by Building America teams. Air-tight and well-insulated homes have little or no tolerance for drying if they get wet; moisture control is critical. That's why Building America research establishing vapor retarder classifications and their appropriate applications has been instrumental in the market transformation to high-performance homes. As buildings have gotten tighter over the past several decades, questions about vapor retarders and vapor barriers have confounded builders and code developers. Vapor barriers have traditionally been installed on the warm in winter side of the wall assembly in an attempt to keep interior moisture from entering the wall cavity

47

Evaluating transport coefficients in real time thermal field theory  

E-Print Network (OSTI)

Transport coefficients in a hadronic gas have been calculated earlier in the imaginary time formulation of thermal field theory. The steps involved are to relate the defining retarded correlation function to the corresponding time-ordered one and to evaluate the latter in the conventional perturbation expansion. Here we carry out both the steps in the real time formulation.

S. Mallik; Sourav Sarkar

2012-11-12T23:59:59.000Z

48

Novel Coatings Show Great Promise as Flame Retardants in ...  

Science Conference Proceedings (OSTI)

... treatment has the potential to deliver a low flammability PUF without major change to the foam manufacturing process, thus saving time and money. ...

2011-08-02T23:59:59.000Z

49

Study of fire retardant behavior of carbon nanotube membranes and carbon nanofiber paper in carbon fiber  

E-Print Network (OSTI)

Study of fire retardant behavior of carbon nanotube membranes and carbon nanofiber paper in carbon Accepted 14 January 2010 Available online 20 January 2010 A B S T R A C T Single-walled carbon nanotube (SWCNT) and multi-walled carbon nanotube (MWCNT) membranes (buckypaper) and carbon nanofiber (CNF) paper

Das, Suman

50

Gridded retarding pressure sensor for ion and neutral particle analysis in flowing plasmas  

E-Print Network (OSTI)

configuration can be used to measure the ion energy distribution. Preliminary data from this probe were takenGridded retarding pressure sensor for ion and neutral particle analysis in flowing plasmas Lyon B. Kinga) and Alec D. Gallimoreb) Plasmadynamics and Electric Propulsion Laboratory, Department

King, Lyon B.

51

Salt Selected (FINAL)  

NLE Websites -- All DOE Office Websites (Extended Search)

WHY SALT WAS SELECTED AS A DISPOSAL MEDIUM WHY SALT WAS SELECTED AS A DISPOSAL MEDIUM Waste Isolation Pilot Plant U.S. Department Of Energy Government officials and scientists chose the Waste Isolation Pilot Plant (WIPP) site through a selection process that started in the 1950s. At that time, the National Academy of Sciences conducted a nationwide search for geological formations stable enough to contain radioactive wastes for thousands of years. In 1955, after extensive

52

Role of retardation in 3-D relativistic equations  

E-Print Network (OSTI)

Equal-time Green's function is used to derive a three-dimensional integral equation from the Bethe-Salpeter equation. The resultant equation, in the absence of anti-particles, is identical to the use of time-ordered diagrams, and has been used within the framework of $\\phi^2\\sigma$ coupling to study the role of energy dependence and non-locality when the two-body potential is the sum of $\\sigma$-exchange and crossed $\\sigma$ exchange. The results show that non-locality and energy dependence make a substantial contribution to both the on-shell and off-shell amplitudes.

A. D. Lahiff; I. R. Afnan

1997-08-20T23:59:59.000Z

53

Author Select  

Office of Scientific and Technical Information (OSTI)

Author Select Last Name First Name search Type in a name, or the first few letters of a name, in one or both of appropriate search boxes above and select "Go". An attempt will be...

54

Select Publications  

NLE Websites -- All DOE Office Websites (Extended Search)

Dosanjh » Select Dosanjh » Select Publications Select Publications Sort by: Date | Author | Type 2013 Richard A. Barrett, Shekhar Borkar, Sudip S. Dosanjh, Simon D. Hammond, Michael A. Heroux, X. Sharon Hu, Justin Luitjens, Steven G. Parker, John Shalf, Li Tang, "On the Role of Co-design in High Performance Computing", Transition of HPC Towards Exascale Computing, E.H. D'Hollander et. al (Eds.), IOS Press, 2013, ( November 1, 2013) Download File: Codesign-Paper.pdf (pdf: 867 KB) Rolf Riesen, Sudip Dosanjh, Larry Kaplan, "The ExaChallenge Symposium", IBM Research Paper, August 26, 2013, Download File: ExaChallenge2012.pdf (pdf: 1.4 MB) S. Dosanjh, R. Barrett, D. Doerfler, S. Hammond, K. Hemmert, M. Heroux, P. Lin, K. Pedretti, A. Rodrigues, T. Trucano, J.Juitjens, "Exascale Design

55

Selected References  

Science Conference Proceedings (OSTI)

...R. Hirsch, Exploring Color Photography, 3rd ed., McGraw-Hill, Times Mirror Higher Education Group, 1997...

56

Development of flame retardant PV module encapsulants: Volume 1. Final report  

DOE Green Energy (OSTI)

This Phase 1 final report covers the work performed by Springborn Testing and Research, Inc., for the period October 1, 1997 to June 30, 1998 under the Department of Energy Cooperative Agreement Number DE-FC36-97GO10255, entitled Development of Flame Retardant PV Module Encapsulants. While use of roof-mounted arrays has always been an attractive means of deploying PV, only within recent years have such building integrated concepts (BIPV) found renewed interest among module makers and end-users. Prior to building integrated and rooftop applications, flammability requirements for modules have not been a great industry concern. However, with growing interest in BIPV and the requirement for building code requirements for commercial and industrial structures, flammability issues have become a barrier to entry for many module constructions into this potentially huge domestic market for PV. The overall goal of the 3 phase PV BONUS two project is to develop and commercialize a line of fire retardant encapsulation materials to serve the emerging building integrated and building mounted PV market. The objectives of the Phase 1 effort are limited to concept development and business planning activities.

Galica, J.P.

1998-06-01T23:59:59.000Z

57

Preliminary measurement of time-dependent B{sub d}{sup 0}-B{sub d}{sup 0} mixing using topology and charge selected semi-leptonic B decays  

SciTech Connect

The time dependence of B{sub d}{sup 0}-B{sub d}{sup 0} mixing has been measured using a sample of 150,000 hadronic Z{sup 0} decays collected by the SLD experiment at the SLC between 1993 and 1995. The analysis identifies the semileptonic decays of B mesons with high (p, p{sub t}) leptons and reconstructs the B meson decay length and charge by vertexing the lepton with a partially reconstructed D meson. Vertex charge is used to enrich the selection of neutral over charged B mesons. This method results in a sample of 581 neutral decays with high charge purity. The B candidate is tagged at production with a combined tag that exploits the large polarized b forward-backward asymmetry in conjunction with the opposite hemisphere b jet charge. The final state is tagged by the sign of the high (p, p{sub t}) lepton. From their preliminary analysis the authors find a mass difference between the two B{sub d}{sup 0} mass eigenstates of, {Delta}m{sub d} = 0.452 {+-} 0.074(stat) {+-} 0.049(syst) ps{sup {minus}1}.

NONE

1996-07-01T23:59:59.000Z

58

Layer-by-Layer Nanocoatings with Flame Retardant and Oxygen Barrier Properties: Moving Toward Renewable Systems  

E-Print Network (OSTI)

Numerous studies have focused on enhancing the flame retardant behavior of cotton and polyurethane foam. Some of the most commonly used treatments (e.g., brominated compounds) have raised concerns with regard to toxicity and environmental persistence. These concerns have led to significant research into the use of alternative approaches, including polymer nanocomposites prepared from more environmentally benign nanoparticles. These particles migrate to the surface from the bulk during fire exposure to form a barrier on the surface that protects the underlying polymer. This theory of fire suppression in bulk nanocomposites inspired the use of layer-by-layer (LbL) assembly to create nanocoatings in an effort to produce more effective and environmentally-benign flame retardant treatments. Negatively charged silica nanoparticles of two different sizes were paired with either positively charged silica or cationic polyethylenimine (PEI) to create thin film assemblies. When applying these films to cotton fabric, all coated fabrics retained their weave structure after being exposed to a vertical flame test, while uncoated cotton was completely destroyed. Micro combustion calorimetry confirmed that coated fabrics exhibited a reduced peak heat release rate, by as much as 20% relative to the uncoated control. Even so, this treatment would not pass the standard UL94 vertical flame test, necessitating a more effective treatment. Positively- charged chitosan (CH) was paired with montmorillonite (MMT) clay to create a renewable flame retardant nanocoating for polyurethane foam. This coating system completely stops the melting of a flexible polyurethane foam when exposed to direct flame from a butane torch, with just 10 bilayers (~ 30 nm thick). The same coated foam exhibited a reduced peak heat release rate, by as much as 52%, relative to the uncoated control. This same nanobrick wall coating is able to impart gas barrier to permeate plastic film. Multilayered thin films were assembled with "green" food contact approved materials (i.e., chitosan, polyacrylic acid (PAA) and montmorillonite clay). Only ten CH-PAA-CH-MMT quadlayers (~90 nm thick) cause polylactic acid (PLA) film to behave like PET in terms of oxygen barrier. A thirty bilayer CH-MMT assembly (~100 nm thick) on PLA exhibits an oxygen transmission rate (OTR) below the detection limit of commercial instrumentation (<= 0.005 cm^3/(m^2*day*atm)). This is the same recipe used to impart flame retardant behavior to foam, but it did not provide effective FR to cotton fabric, so a very different recipe was used. Thin films of fully renewable electrolytes, chitosan and phytic acid (PA), were deposited on cotton fabric in an effort to reduce flammability through an intumescent effect. Altering the pH of aqueous deposition solutions modifies the composition of the final nanocoating. Fabrics coated with highest PA content multilayers completely extinguished the flame and reduced peak heat release (pkHRR) and total heat release of 60% and 76%, respectively. This superior performance is believed to be due to high phosphorus content that enhances the intumescent behavior of these nanocoatings.

Laufer, Galina 1985-

2012-12-01T23:59:59.000Z

59

Source Selection Guide  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Source Selection Source Selection Overview This chapter provides guidance to the acquisition team on conducting source selection in accordance with Part 15 of the Federal Acquisition Regulation (FAR). Background The mid 1990's was a time of significant change in many areas of procurement, particularly in the introduction of new tools and processes that help the procurement professional better meet the needs of demanding customers. The passage of the Federal Acquisition Streamlining Act in 1994 and the Federal Acquisition Reform Act in 1995 , coupled with Government-wide and Department of Energy (DOE) contract reform efforts not only changed traditional procurement processes but also changed the role of the procurement professional. No longer are procurement

60

Mass-resolved retarding field energy analyzer and its measurement of ion energy distribution in helicon plasma  

E-Print Network (OSTI)

Mass-resolved retarding field energy analyzer and its measurement of ion energy distribution) are measured at rf power of 1000 W. The results show that the fairly broad energy distributions of different analyzer; Ion energy distribution; Helicon plasma 1. Introduction It is well recognized that ion

Zexian, Cao

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

/select/modify/life  

Science Conference Proceedings (OSTI)

... OOF: Finite Element Analysis of Microstructures. Table of Contents, /select/modify/life, OOF home. Prev, ... select/modify/life. /select ...

2013-08-23T23:59:59.000Z

62

ATRX ADD domain links an atypical histone methylation recognition mechanism to human mental-retardation syndrome  

SciTech Connect

ATR-X (alpha-thalassemia/mental retardation, X-linked) syndrome is a human congenital disorder that causes severe intellectual disabilities. Mutations in the ATRX gene, which encodes an ATP-dependent chromatin-remodeler, are responsible for the syndrome. Approximately 50% of the missense mutations in affected persons are clustered in a cysteine-rich domain termed ADD (ATRX-DNMT3-DNMT3L, ADD{sub ATRX}), whose function has remained elusive. Here we identify ADD{sub ATRX} as a previously unknown histone H3-binding module, whose binding is promoted by lysine 9 trimethylation (H3K9me3) but inhibited by lysine 4 trimethylation (H3K4me3). The cocrystal structure of ADD{sub ATRX} bound to H3{sub 1-15}K9me3 peptide reveals an atypical composite H3K9me3-binding pocket, which is distinct from the conventional trimethyllysine-binding aromatic cage. Notably, H3K9me3-pocket mutants and ATR-X syndrome mutants are defective in both H3K9me3 binding and localization at pericentromeric heterochromatin; thus, we have discovered a unique histone-recognition mechanism underlying the ATR-X etiology.

Iwase, Shigeki; Xiang, Bin; Ghosh, Sharmistha; Ren, Ting; Lewis, Peter W.; Cochrane, Jesse C.; Allis, C. David; Picketts, David J.; Patel, Dinshaw J.; Li, Haitao; Shi, Yang (Harvard-Med); (Ottawa Hosp.); (MSKCC); (Rockefeller); (CH-Boston); (Tsinghua); (Mass. Gen. Hosp.)

2011-07-19T23:59:59.000Z

63

ATRX ADD Domain Links an Atypical Histone Methylation Recognition Mechanism to Human Mental-Retardation Syndrome  

SciTech Connect

ATR-X (alpha-thalassemia/mental retardation, X-linked) syndrome is a human congenital disorder that causes severe intellectual disabilities. Mutations in the ATRX gene, which encodes an ATP-dependent chromatin-remodeler, are responsible for the syndrome. Approximately 50% of the missense mutations in affected persons are clustered in a cysteine-rich domain termed ADD (ATRX-DNMT3-DNMT3L, ADD{sub ATRX}), whose function has remained elusive. Here we identify ADD{sub ATRX} as a previously unknown histone H3-binding module, whose binding is promoted by lysine 9 trimethylation (H3K9me3) but inhibited by lysine 4 trimethylation (H3K4me3). The cocrystal structure of ADD{sub ATRX} bound to H3{sub 1-15}K9me3 peptide reveals an atypical composite H3K9me3-binding pocket, which is distinct from the conventional trimethyllysine-binding aromatic cage. Notably, H3K9me3-pocket mutants and ATR-X syndrome mutants are defective in both H3K9me3 binding and localization at pericentromeric heterochromatin; thus, we have discovered a unique histone-recognition mechanism underlying the ATR-X etiology.

S Iwase; B Xiang; S Ghosh; T Ren; P Lewis; J Cochrane; C Allis; D Picketts; D Patel; et al.

2011-12-31T23:59:59.000Z

64

Scanning retarding field analyzer for plasma profile measurements in the boundary of the Alcator C-Mod tokamak  

SciTech Connect

A new Retarding Field Analyzer (RFA) head has been created for the outer-midplane scanning probe system on the Alcator C-Mod tokamak. The new probe head contains back-to-back retarding field analyzers aligned with the local magnetic field. One faces 'upstream' into the field-aligned plasma flow and the other faces 'downstream' away from the flow. The RFA was created primarily to benchmark ion temperature measurements of an ion sensitive probe; it may also be used to interrogate electrons. However, its construction is robust enough to be used to measure ion and electron temperatures up to the last-closed flux surface in C-Mod. A RFA probe of identical design has been attached to the side of a limiter to explore direct changes to the boundary plasma due to lower hybrid heating and current drive. Design of the high heat flux (>100 MW/m{sup 2}) handling probe and initial results are presented.

Brunner, D.; LaBombard, B.; Ochoukov, R.; Whyte, D. [MIT PSFC Cambridge, Massachusetts 02139 (United States)

2013-03-15T23:59:59.000Z

65

Polybrominated diphenyl ethers (PBDEs) in leachates from selected landfill sites in South Africa  

Science Conference Proceedings (OSTI)

The last few decades have seen dramatic growth in the scale of production and the use of polybrominated diphenyl ethers (PBDEs) as flame retardants. Consequently, PBDEs such as BDE -28, -47, -66, -71, -75, -77, -85, -99, -100, -119, -138, -153, -154, and -183 have been detected in various environmental matrices. Generally, in South Africa, once the products containing these chemicals have outlived their usefulness, they are discarded into landfill sites. Consequently, the levels of PBDEs in leachates from landfill sites may give an indication of the general exposure and use of these compounds. The present study was aimed at determining the occurrence and concentrations of most common PBDEs in leachates from selected landfill sites. The extraction capacities of the solvents were also tested. Spiked landfill leachate samples were used for the recovery tests. Separation and determination of the PBDE congeners were carried out with a gas chromatograph equipped with Ni{sup 63} electron capture detector. The mean percentage recoveries ranged from 63% to 108% (n = 3) for landfill leachate samples with petroleum ether giving the highest percentage extraction. The mean concentrations of PBDEs obtained ranged from ND to 2670 pg l{sup -1}, ND to 6638 pg l{sup -1}, ND to 7230 pg l{sup -1}, 41 to 4009 pg l{sup -1}, 90 to 9793 pg l{sup -1} for the Garankuwa, Hatherly, Kwaggarsrand, Soshanguve and Temba landfill sites, respectively. Also BDE -28, -47, -71 and BDE-77 were detected in the leachate samples from all the landfill sites; and all the congeners were detected in two of the oldest landfill sites. The peak concentrations were recorded for BDE-47 at three sites and BDE-71 and BDE-75 at two sites. The highest concentration, 9793 {+-} 1.5 pg l{sup -1}, was obtained for the Temba landfill site with the highest BOD value. This may suggest some influence of organics on the level of PBDEs. Considering the leaching characteristics of brominated flame retardants, there is a high possibility that with time these compounds may infiltrate into the groundwater around the sites since most of the sites are not adequately lined.

Odusanya, David O. [Department of Environmental, Water and Earth Sciences, Faculty of Science, Tshwane University of Technology, Private Bag X680, 175 Nelson Mandela Drive, Arcadia, Pretoria 0001 (South Africa); Okonkwo, Jonathan O. [Department of Environmental, Water and Earth Sciences, Faculty of Science, Tshwane University of Technology, Private Bag X680, 175 Nelson Mandela Drive, Arcadia, Pretoria 0001 (South Africa)], E-mail: OkonkwoOJ@tut.ac.za; Botha, Ben [Department of Environmental, Water and Earth Sciences, Faculty of Science, Tshwane University of Technology, Private Bag X680, 175 Nelson Mandela Drive, Arcadia, Pretoria 0001 (South Africa)

2009-01-15T23:59:59.000Z

66

Metric Selection for Ecosystem Restoration  

E-Print Network (OSTI)

managers identify the best metrics to evaluate and select the recommended restoration plan, monitor and assess progress toward achieving project objectives, and, if necessary, inform adaptive management decisions. Performance metrics, or measurable system components used to estimate and track the state of critical aspects of the project, are often the basis for project decision making and furthering scientific understanding. As such, ecosystem restoration planners should take time to carefully select an appropriate and effective metric set. To help planners with this task, this technical note accomplishes the following: 1. Reviews current USACE ecosystem restoration planning and monitoring policy, regulations and guidelines. 2. Explains the importance of metric selection and its roles during planning and post-construction monitoring and assessment. 3. Reviews common options for identifying and selecting metrics including conceptual modeling, historical precedence, and best professional judgment. 4. Presents two metric evaluation methods, screening and multi-criteria decision analysis. 5. Discusses metric application to ecosystem restoration project planning and monitoring.

Matteo Convertino; Kelsie Baker; Connie Lu; John T. Vogel; Kyle Mckay; Igor Linkov

2013-01-01T23:59:59.000Z

67

Managing time  

Science Conference Proceedings (OSTI)

Professionals overwhelmed with information glut can find hope from new insights about time management.

Peter J. Denning

2011-03-01T23:59:59.000Z

68

Source Selection Guide | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Source Selection Guide Source Selection Guide Source Selection Guide More Documents & Publications Source Selection Guide Source Selection Guide Source Selection...

69

Entropic Time  

Science Conference Proceedings (OSTI)

The formulation of quantum mechanics within the framework of entropic dynamics includes several new elements. In this paper we concentrate on one of them: the implications for the theory of time. Entropic time is introduced as a book-keeping device to keep track of the accumulation of changes. One new feature is that, unlike other concepts of time appearing in the so-called fundamental laws of physics, entropic time incorporates a natural distinction between past and future.

Caticha, Ariel [Department of Physics, University at Albany-SUNY, Albany, NY 12222 (United States)

2011-03-14T23:59:59.000Z

70

Randomized selection on the GPU  

SciTech Connect

We implement here a fast and memory-sparing probabilistic top N selection algorithm on the GPU. To our knowledge, this is the first direct selection in the literature for the GPU. The algorithm proceeds via a probabilistic-guess-and-chcck process searching for the Nth element. It always gives a correct result and always terminates. The use of randomization reduces the amount of data that needs heavy processing, and so reduces the average time required for the algorithm. Probabilistic Las Vegas algorithms of this kind are a form of stochastic optimization and can be well suited to more general parallel processors with limited amounts of fast memory.

Monroe, Laura Marie [Los Alamos National Laboratory; Wendelberger, Joanne R [Los Alamos National Laboratory; Michalak, Sarah E [Los Alamos National Laboratory

2011-01-13T23:59:59.000Z

71

Source Selection | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Source Selection Source Selection Source SelectionSource Selection Boards Source Evaluation Board (SEB) Monthly Status Reporting Requirement (pdf) Source Evaluation Board (SEB)...

72

ARPA-E Project Selections  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

NEUP Project Selections NEUP Project Selections September 21, 2011 These projects have been selected for negotiation of awards; final award amounts may vary. Lead Research University Grant Amount Lead University Location (City, State) Project Description 1) Integrated Research Project Awards Texas A&M University $4,500,000 College Station, TX Researchers will receive $4.5 million over the next three years to research aging of used nuclear fuel and canisters that are stored for an extended period of time. Partners include Boise State University, North Carolina State University, the University of Florida, the University of Illinois-Urbana Champaign, the University of Wisconsin-Madison, Savannah River National Laboratory and Pacific Northwest National Laboratory.

73

Solar selective coatings  

DOE Green Energy (OSTI)

The definition, fabrication, and specification of solar selective absorber surfaces are discussed. Also, the nature of solar radiation and thermal radiation in relation to selective surfaces is considered. (WHK)

Mattox, D. M.

1977-01-01T23:59:59.000Z

74

TIMING APPARATUS  

DOE Patents (OSTI)

The timing device comprises an escapement wheel and pallet, a spring drive to rotate the escapement wheel to a zero position, means to wind the pretensioned spring proportional to the desired signal time, and a cam mechanism to control an electrical signal switch by energizing the switch when the spring has been wound to the desired position, and deenergizing it when it reaches the zero position. This device produces an accurately timed signal variably witain the control of the operator.

Bennett, A.E.; Geisow, J.C.H.

1956-04-17T23:59:59.000Z

75

Quantum tunneling time  

E-Print Network (OSTI)

A simple model of a quantum clock is applied to the old and controversial problem of how long a particle takes to tunnel through a quantum barrier. The model I employ has the advantage of yielding sensible results for energy eigenstates, and does not require the use of time-dependant wave packets. Although the treatment does not forbid superluminal tunneling velocities, there is no implication of faster-than-light signaling because only the transit duration is measurable, not the absolute time of transit. A comparison is given with the weak-measurement post-selection calculations of Steinberg.

P. C. W. Davies

2004-03-01T23:59:59.000Z

76

Interpreting a conformally flat pure radiation space-time  

E-Print Network (OSTI)

A physical interpretation is presented of the general class of conformally flat pure radiation metrics that has recently been identified by Edgar and Ludwig. It is shown that, at least in the weak field limit, successive wave surfaces can be represented as null (half) hyperplanes rolled around a two-dimensional null cone. In the impulsive limit, the solution reduces to a pp-wave whose direction of propagation depends on retarded time. In the general case, there is a coordinate singularity which corresponds to an envelope of the wave surfaces. The global structure is discussed and a possible vacuum extension through the envelope is proposed.

J. B. Griffiths; J. Podolsky

1998-08-24T23:59:59.000Z

77

Managed Pressure Drilling Candidate Selection  

E-Print Network (OSTI)

Managed Pressure Drilling now at the pinnacle of the 'Oil Well Drilling' evolution tree, has itself been coined in 2003. It is an umbrella term for a few new drilling techniques and some preexisting drilling techniques, all of them aiming to solve several drilling problems, including non-productive time and/or drilling flat time issues. These techniques, now sub-classifications of Managed Pressure Drilling, are referred to as 'Variations' and 'Methods' of Managed Pressure Drilling. Although using Managed Pressure Drilling for drilling wells has several benefits, not all wells that seem a potential candidate for Managed Pressure Drilling, need Managed Pressure Drilling. The drilling industry has numerous simulators and software models to perform drilling hydraulics calculations and simulations. Most of them are designed for conventional well hydraulics, while some can perform Underbalanced Drilling calculations, and a select few can perform Managed Pressure Drilling calculations. Most of the few available Managed Pressure Drilling models are modified Underbalanced Drilling versions that fit Managed Pressure Drilling needs. However, none of them focus on Managed Pressure Drilling and its candidate selection alone. An 'Managed Pressure Drilling Candidate Selection Model and software' that can act as a preliminary screen to determine the utility of Managed Pressure Drilling for potential candidate wells are developed as a part of this research dissertation. The model and a flow diagram identify the key steps in candidate selection. The software performs the basic hydraulic calculations and provides useful results in the form of tables, plots and graphs that would help in making better engineering decisions. An additional Managed Pressure Drilling worldwide wells database with basic information on a few Managed Pressure Drilling projects has also been compiled that can act as a basic guide on the Managed Pressure Drilling variation and project frequencies and aid in Managed Pressure Drilling candidate selection.

Nauduri, Anantha S.

2009-05-01T23:59:59.000Z

78

Bayesian Variable Selection for Nowcasting Economic Time Series  

E-Print Network (OSTI)

motivation Want to use Google Trends data to nowcast economic series unemployment may be predicted by "job;Avoid spurious regression How to control for trend and seasonality? Build a model for the predictable-chosen contemporaneous regressors from Google Trends non-seasonal AR1: yt = a1yt-1 + bxt + et seasonal AR1: yt = a1yt-1

Varian, Hal R.

79

RISQ - Query Selection Criteria  

Science Conference Proceedings (OSTI)

Figure 2 - RISQ Search. ... Selected Taxonomy Terms. Threat Analysis. ... To define a custom keyword: Enter the keyword in text form in the box to the left. ...

80

2008 present Publications (selection)  

E-Print Network (OSTI)

. Mathias Wegner, Kiel Professor Stefan Michel, Lausanne Patent applications (selection) Media Cosmopolitan http://scentoflove.com/i/file/media/cosmopolitan_0710.pdf http://www.trendhunter.com

Wegner, Mathias

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Baldrige Examiner Selection  

Science Conference Proceedings (OSTI)

... Examiner SelectionWhat Do Examiners Do? ... leadership; strategic planning; customer service, human resource, and ... a board member does not meet ...

2013-01-29T23:59:59.000Z

82

VARIABLE TIME-INTERVAL GENERATOR  

DOE Patents (OSTI)

This patent relates to a pulse generator and more particularly to a time interval generator wherein the time interval between pulses is precisely determined. The variable time generator comprises two oscillators with one having a variable frequency output and the other a fixed frequency output. A frequency divider is connected to the variable oscillator for dividing its frequency by a selected factor and a counter is used for counting the periods of the fixed oscillator occurring during a cycle of the divided frequency of the variable oscillator. This defines the period of the variable oscillator in terms of that of the fixed oscillator. A circuit is provided for selecting as a time interval a predetermined number of periods of the variable oscillator. The output of the generator consists of a first pulse produced by a trigger circuit at the start of the time interval and a second pulse marking the end of the time interval produced by the same trigger circuit.

Gross, J.E.

1959-10-31T23:59:59.000Z

83

Digital time delay  

DOE Patents (OSTI)

Method and apparatus are provided for generating an output pulse following a trigger pulse at a time delay interval preset with a resolution which is high relative to a low resolution available from supplied clock pulses. A first lumped constant delay provides a first output signal at predetermined interpolation intervals corresponding to the desired high resolution time interval. Latching circuits latch the high resolution data to form a first synchronizing data set. A selected time interval has been preset to internal counters and corrected for circuit propagation delay times having the same order of magnitude as the desired high resolution. Internal system clock pulses count down the counters to generate an internal pulse delayed by an internal which is functionally related to the preset time interval. A second LCD corrects the internal signal with the high resolution time delay. A second internal pulse is then applied to a third LCD to generate a second set of synchronizing data which is complementary with the first set of synchronizing data for presentation to logic circuits. The logic circuits further delay the internal output signal with the internal pulses. The final delayed output signal thereafter enables the output pulse generator to produce the desired output pulse at the preset time delay interval following input of the trigger pulse.

Martin, A.D.

1986-05-09T23:59:59.000Z

84

Digestion time  

NLE Websites -- All DOE Office Websites (Extended Search)

Digestion time Digestion time Name: Don Mancosh Location: N/A Country: N/A Date: N/A Question: I have always given the rule of thumb in class that material we eat is with us for about 24 hours before exiting the body. The question arises about the time value of liquids. Getting a big coke prior to a 3 hour drive generally means that there will be a stop along the way. Is there a generalization made about liquids in the body similar to the one for solid food? Replies: A physician would give a better answer, but I hazard this: the only liquids which people consume (deliberately) in significant quantities are water, ethyl alcohol and various oils. Water and alcohol are absorbed on a time scale of seconds to minutes through the mouth, stomach and digestive tract. The oils are huge molecules, so I'd guess like any other greasy food they get absorbed in the upper digestive tract. Some of them, perhaps the longest and most nonpolar, are not absorbed at all --- cf. the old-time remedy of mineral oil for constipation --- so there should be some average time-before-what's-left-is-excreted such as you're looking for, and my (wild) guess is that it would not differ substantially from that for food. You can define an average lifetime in the body for alcohol, since the natural level is zero. Rough guidelines are widespread in the context of drunk driving laws. But this is not really possible for water. One's body is normally full up to the brim with water, and there's no way for the body to distinguish between water molecules recently absorbed and molecules that've been moping around since the Beatles split up. Thus the water entering the toilet bowl after the pit stop is not in general the same water as was in the big coke. If you were to consider for water just the average time between drinking and peeing, it would seem to depend strongly on how well hydrated the body was before the drink, and how much was drunk. During sustained heavy exertion in the sun and dry air one can easily drink a pint of water an hour without peeing at all. On the other hand, if one is willing to drink enough water fast enough, so as to establish a high excess of body water one can pee 8 ounces 15 minutes or less after drinking 8 ounces.

85

Selectable fragmentation warhead  

DOE Patents (OSTI)

This report discusses a selectable fragmentation warhead which is capable of producing a predetermined number of fragments from a metal plate, and accelerating the fragments toward a target. A first explosive located adjacent to the plate is detonated at selected number of points by laser-driven slapper detonators. In one embodiment, a smoother-disk and a second explosive, located adjacent to the first explosive, serve to increase acceleration of the fragments toward a target. The ability to produce a selected number of fragments allows for effective destruction of a chosen target.

Bryan, C.S.; Paisley, D.L.; Montoya, N.I.; Stahl, D.B.

1992-12-31T23:59:59.000Z

86

A statistical analysis of systematic errors in temperature and ram velocity estimates from satellite-borne retarding potential analyzers  

SciTech Connect

The use of biased grids as energy filters for charged particles is common in satellite-borne instruments such as a planar retarding potential analyzer (RPA). Planar RPAs are currently flown on missions such as the Communications/Navigation Outage Forecast System and the Defense Meteorological Satellites Program to obtain estimates of geophysical parameters including ion velocity and temperature. It has been shown previously that the use of biased grids in such instruments creates a nonuniform potential in the grid plane, which leads to inherent errors in the inferred parameters. A simulation of ion interactions with various configurations of biased grids has been developed using a commercial finite-element analysis software package. Using a statistical approach, the simulation calculates collected flux from Maxwellian ion distributions with three-dimensional drift relative to the instrument. Perturbations in the performance of flight instrumentation relative to expectations from the idealized RPA flux equation are discussed. Both single grid and dual-grid systems are modeled to investigate design considerations. Relative errors in the inferred parameters for each geometry are characterized as functions of ion temperature and drift velocity.

Klenzing, J. H.; Earle, G. D.; Heelis, R. A.; Coley, W. R. [William B. Hanson Center for Space Sciences, University of Texas at Dallas, 800 W. Campbell Rd. WT15, Richardson, Texas 75080 (United States)

2009-05-15T23:59:59.000Z

87

Dynamic Selection of Software Components in the Face of Changing  

E-Print Network (OSTI)

Dynamic Selection of Software Components in the Face of Changing Requirements Salah Merad, Rogério Science, Claremont Tower, Claremont Road, Newcastle upon Tyne, NE1 7RU, UK #12;1 Dynamic Selection having a specific profile, and a decision maker that selects the best component subject to the time

Newcastle upon Tyne, University of

88

A Cautionary Tale of Caterpillars and Selectional Interference  

E-Print Network (OSTI)

A Cautionary Tale of Caterpillars and Selectional Interference W. Garrett Mitchener December 14-trivial. In laboratory experiments by Nijhout and in computer simulations, one can selectively breed caterpillars based experiments and computer simulations yield striking complexity. Selecting for size and time simultaneously

Mitchener, W. Garrett

89

SOAJ Search : Your Selections  

Office of Scientific and Technical Information (OSTI)

Your Selections Back To Previous Page Selections - of First Page Previous Page Next Page Last Page Back To Previous Page You have 0 selections. Click the checkboxes clipping.addClipping on the results or alert results pages to add to your selections. U.S. Department of Energy Office of Scientific and Technical Information Website Policies/Important Links Science Accelerator science.gov WorldWideScience.org U.S. Department of Energy Office of Science Email Results Use this form to email your search results * Email this to: * Your Name: Comments: URL only?: Number of results: 10 20 50 100 200 All Email Format: HTML TEXT * Required field Print Results Use this form to print results. The page of currently displayed results. The entire list of clipped results. The first

90

Supplier Selection Management Process  

NLE Websites -- All DOE Office Websites (Extended Search)

ADMP-002 Vendor Selection and Management Process 11_0203 1 of 9 ADMP-002 Vendor Selection and Management Process 11_0203 1 of 9 EOTA - Business Process Document Title: Vendor Selection and Management Process Document Number: ADMP-002 Rev. 11_0203 Document Owner: Elizabeth Sousa Backup Owner: Melissa Otero Approver(s): Melissa Otero Parent Document: Q-001, Quality Manual Notify of Changes: EOTA Employees Referenced Document(s): ADMF-009 Vendor Audit Plan, ADMF-010 Vendor Audit Checklist, ADMF-011 Vendor Audit Report, ADMF-015 Vendor Evaluation Record, ADMP-001 Procurement Process, ADMF-016 EOTA Vendor List, REG-003 Record Register ADMP-002 Vendor Selection and Management Process 11_0203 2 of 9 Revision History: Rev. Description of Change A Initial Release 08_1110 Added verbiage and reference for ADMF-016, EOTA Vendor List to process.

91

Science Accelerator : Your Selections  

NLE Websites -- All DOE Office Websites (Extended Search)

Your Selections Back To Previous Page Selections - of First Page Previous Page Next Page Last Page Back To Previous Page You have 0 selections. Click the checkboxes clipping.addClipping on the results or alert results pages to add to your selections. Some links on this page may take you to non-federal websites. Their policies may differ from this site. U.S. Department of Energy U.S. Department of Energy Office of Science Office of Scientific and Technical Information Website Policies/Important Links Science Accelerator science.gov WorldWideScience.org Deep Web Technologies Email Results Use this form to email your search results * Email this to: * Your Name: Comments: URL only?: Number of results: 10 20 50 100 200 All Email Format: HTML TEXT * Required field Print Results

92

TAC KBP Entity Selection  

Science Conference Proceedings (OSTI)

... A few terms related to Entity Selection tend to overlap in ... that you want to search for, and hit enter. The search will result in a list of documents that ...

2012-10-17T23:59:59.000Z

93

Solar selective absorption coatings  

DOE Patents (OSTI)

A new class of solar selective absorption coatings are disclosed. These coatings comprise a structured metallic overlayer such that the overlayer has a sub-micron structure designed to efficiently absorb solar radiation, while retaining low thermal emissivity for infrared thermal radiation. A sol-gel layer protects the structured metallic overlayer from mechanical, thermal, and environmental degradation. Processes for producing such solar selective absorption coatings are also disclosed.

Mahoney, Alan R. (Albuquerque, NM); Reed, Scott T. (Albuquerque, NM); Ashley, Carol S. (Albuquerque, NM); Martinez, F. Edward (Horseheads, NY)

2004-08-31T23:59:59.000Z

94

Solar selective absorption coatings  

DOE Patents (OSTI)

A new class of solar selective absorption coatings are disclosed. These coatings comprise a structured metallic overlayer such that the overlayer has a sub-micron structure designed to efficiently absorb solar radiation, while retaining low thermal emissivity for infrared thermal radiation. A sol-gel layer protects the structured metallic overlayer from mechanical, thermal, and environmental degradation. Processes for producing such solar selective absorption coatings are also disclosed.

Mahoney, Alan R. (Albuquerque, NM); Reed, Scott T. (Albuquerque, NM); Ashley, Carol S. (Albuquerque, NM); Martinez, F. Edward (Horseheads, NY)

2003-10-14T23:59:59.000Z

95

Time Brightness  

NLE Websites -- All DOE Office Websites (Extended Search)

Perlmutter, et al., in Thermonuclear Supernovae, NATO ASI, v. 486 (1997) Perlmutter, et al., in Thermonuclear Supernovae, NATO ASI, v. 486 (1997) Cosmology from . . . Time Brightness ... . . . 50-100 Fields Lunar Calendar Scheduled Follow-Up Imaging at Hubble, Cerro Tololo, WIYN, Isaac Newton Scheduled Follow-Up Spectroscopy at Keck Almost 1000 Galaxies per Field RESULT: ~24 Type Ia supernovae discovered while still brightening, at new moon Berkeley Lab Keck WIYN Cerro Tololo Isaac Newton Hubble Strategy We developed a strategy to guarantee a group of supernova discoveries on a certain date. Just after a new moon, we observe some 50 to 100 high-galactic lattitute fields-each containing almost a thousand high-redshift galaxies-in two nights on the Cerro Tololo 4-meter telescope with Tyson & Bernstein's wide-field camera. We return three weeks later to observe the same

96

Spectrally selective glazings  

SciTech Connect

Spectrally selective glazing is window glass that permits some portions of the solar spectrum to enter a building while blocking others. This high-performance glazing admits as much daylight as possible while preventing transmission of as much solar heat as possible. By controlling solar heat gains in summer, preventing loss of interior heat in winter, and allowing occupants to reduce electric lighting use by making maximum use of daylight, spectrally selective glazing significantly reduces building energy consumption and peak demand. Because new spectrally selective glazings can have a virtually clear appearance, they admit more daylight and permit much brighter, more open views to the outside while still providing the solar control of the dark, reflective energy-efficient glass of the past. This Federal Technology Alert provides detailed information and procedures for Federal energy managers to consider spectrally selective glazings. The principle of spectrally selective glazings is explained. Benefits related to energy efficiency and other architectural criteria are delineated. Guidelines are provided for appropriate application of spectrally selective glazing, and step-by-step instructions are given for estimating energy savings. Case studies are also presented to illustrate actual costs and energy savings. Current manufacturers, technology users, and references for further reading are included for users who have questions not fully addressed here.

NONE

1998-08-01T23:59:59.000Z

97

High Selectivity Oxygen Delignification  

DOE Green Energy (OSTI)

Project Objective: The objectives of this project are as follows: (1) Examine the physical and chemical characteristics of a partner mill pre- and post-oxygen delignified pulp and compare them to lab generated oxygen delignified pulps; (2) Apply the chemical selectivity enhancement system to the partner pre-oxygen delignified pulps under mill conditions (with and without any predetermined amounts of carryover) to determine how efficiently viscosity is preserved, how well selectivity is enhanced, if strength is improved, measure any yield differences and/or bleachability differences; and (3) Initiate a mill scale oxygen delignification run using the selectivity enhancement agent, collect the mill data, analyze it, and propose any future plans for implementation.

Lucian A. Lucia

2005-11-15T23:59:59.000Z

98

Prediction of the Environmental Mobility of Arsenic: Selection and Use of Partitioning Coefficients  

Science Conference Proceedings (OSTI)

Arsenic migration is slower than water movement in groundwater environments. As a result, prediction of groundwater arsenic migration requires knowledge of the difference in these transport rates -- defined as the retardation factor. A crucial part of the definition of the retardation factor is the partition coefficient, Kd. Because retardation is a required input for contaminant transport calculations and modeling, Kd must be known, assumed, or estimated to predict retardation. Two fundamental approache...

2002-11-01T23:59:59.000Z

99

Generic selections of subexpressions  

Science Conference Proceedings (OSTI)

Tools for computer languages need position information: compilers for providing better error messages, structure editors for mapping between structural and textual views, and debuggers for navigating through a term, for instance. Manually adding position ... Keywords: datatype-generic programming, haskell, selections

Martijn Van Steenbergen; José Pedro Magalhães; Johan Jeuring

2010-09-01T23:59:59.000Z

100

Industrial Carbon Capture Project Selections  

Energy.gov (U.S. Department of Energy (DOE))

Industrial Carbon Capture Project SelectionsSeptember 2, 2010These projects have been selected for negotiation of awards; final award amounts may vary.

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Flame Retardant Polymer Formulations  

Science Conference Proceedings (OSTI)

... 43% 21% 8% 5% 23% Western Europe Plastic Materials Demand by Segments 2007 ... Lubricants: improvement in processing, release properties ...

2011-11-16T23:59:59.000Z

102

Methods of Materials Selection  

Science Conference Proceedings (OSTI)

Table 7   Performance indices...after specified time C p ρ/λ Thermal storage: maximize energy storage for given

103

Selected State Legislation and  

Gasoline and Diesel Fuel Update (EIA)

and and Selected State Legislation and Regulation in the Annual Energy Outlook Energy Information Administration/Assumptions to the Annual Energy Outlook 2007 156 Appendix A: Handling of Federal and Selected State Legislation and Regulation in the Annual Energy Outlook Legislation Brief Description AEO Handling Basis Residential Sector A. National Appliance Energy Conservation Act of 1987 Requires Secretary of Energy to set minimum efficiency standards for 10 appliance categories. Included for categories represented in the AEO residential sector forecast. a. Room Air Conditioners Current standard of 9.8 EER Federal Register Notice of Final Rulemaking. b. Other Air Conditioners (<5.4 tons) Current standard 10 SEET for central air conditioners and heat

104

Selected State Legislation and  

Gasoline and Diesel Fuel Update (EIA)

and and Selected State Legislation and Regulation in the Annual Energy Outlook U. S. Energy Information Administration/Assumptions to the Annual Energy Outlook 2009 173 Appendix A: Handling of Federal and Selected State Legislation and Regulation in the Annual Energy Outlook Legislation Brief Description AEO Handling Ba sis Residential Sector A. National Appliance Energy Conservation Act of 1987 Requires Secretary of Energy to set minimum efficiency standards for 10 appliance categories. Included for categories represented in the AEO residential sector forecast. a. Room Air Conditioners Current standard of 9.8 EER Federal Register Notice of Final Rulemaking. b. Other Air Conditioners (<5.4 tons) Current standard 10 SEET for central air conditioners and heat

105

Glove Selection Guideline  

NLE Websites -- All DOE Office Websites (Extended Search)

Glove Selection Guideline Glove Selection Guideline Skin contact is a potential source of exposure to toxic materials; it is important that the proper steps be taken to prevent such contact. Most accidents involving hands and arms can be classified under four main hazard categories: chemicals, abrasions, cutting, and heat. There are gloves available that can protect workers from any of these individual hazards or any combination thereof. Gloves should be replaced periodically, depending on frequency of use and permeability to the substance(s) handled. Gloves overtly contaminated should be rinsed and then carefully removed after use. Gloves should also be worn whenever it is necessary to handle rough or sharp-edged objects, and very hot or very cold materials. The type of glove materials to be used in these situations include leather, welder’s gloves,

106

Microsoft Word - Site Selection  

NLE Websites -- All DOE Office Websites (Extended Search)

Selection Selection One of the very first tasks of General Leslie Groves and the Manhattan Project in early 1943 was to locate and acquire sites in the United States where uranium and plutonium could be produced, as well as a site where the atomic bomb actually would be constructed. Production of uranium and plutonium required vast amounts of power. Thus, Oak Ridge, Tennessee, and Hanford, Washington, were chosen because of proximity to major rivers. Oak Ridge could draw on the power of the hydroelectric plants on the Tennessee River. Hanford could use the power from the Columbia River. The cold waters of the Columbia also could be used to cool the plutonium production reactors at Hanford. A third site, with

107

Ion-Selective Membrane Electrodes  

Science Conference Proceedings (OSTI)

...R.A. Durst, Ion-Selective Electrodes, Special Publication 314, National Bureau of Standards, 1969...

108

Chiller Selection: CFC Update  

Science Conference Proceedings (OSTI)

This CFC Update examines the decision factors used in selecting the most cost-effective chiller. The growing concern with emissions contributing to ozone depletion, global warming, and air pollution must be considered. Recent chlorofluorocarbon (CFC) and hydrochlorofluorocarbon (HCFC) phaseout schedules are causing some building owners to consider gas-fired chillers in place of electric chillers. The gas-fired chillers provide cooling without using ozone-depleting refrigerants, and also reduce electric d...

1997-11-04T23:59:59.000Z

109

Selective ion source  

DOE Patents (OSTI)

A ion source is described wherein selected ions maybe extracted to the exclusion of unwanted ion species of higher ionization potential. Also described is a method of producing selected ions from a compound, such as P.sup.+ from PH.sub.3. The invention comprises a plasma chamber, an electron source, a means for introducing a gas to be ionized by electrons from the electron source, means for limiting electron energy from the electron source to a value between the ionization energy of the selected ion species and the greater ionization energy of an unwanted ion specie, and means for extracting the target ion specie from the plasma chamber. In one embodiment, the electrons are generated in a plasma cathode chamber immediately adjacent to the plasma chamber. A small extractor draws the electrons from the plasma cathode chamber into the relatively positive plasma chamber. The energy of the electrons extracted in this manner is easily controlled. The invention is particularly useful for doping silicon with P.sup.+, AS.sup.+, and B.sup.+ without the problematic presence of hydrogen, helium, water, or carbon oxide ions. Doped silicon is important for manufacture of semiconductors and semiconductor devices.

Leung, Ka-Ngo (Hercules, CA)

1996-01-01T23:59:59.000Z

110

Hydrogen-selective membrane  

DOE Patents (OSTI)

A hydrogen-selective membrane comprises a tubular porous ceramic support having a palladium metal layer deposited on an inside surface of the ceramic support. The thickness of the palladium layer is greater than about 10 {micro}m but typically less than about 20 {micro}m. The hydrogen permeation rate of the membrane is greater than about 1.0 moles/m{sup 2} s at a temperature of greater than about 500 C and a transmembrane pressure difference of about 1,500 kPa. Moreover, the hydrogen-to-nitrogen selectivity is greater than about 600 at a temperature of greater than about 500 C and a transmembrane pressure of about 700 kPa. Hydrogen can be separated from a mixture of gases using the membrane. The method may include the step of heating the mixture of gases to a temperature of greater than about 400 C and less than about 1000 C before the step of flowing the mixture of gases past the membrane. The mixture of gases may include ammonia. The ammonia typically is decomposed to provide nitrogen and hydrogen using a catalyst such as nickel. The catalyst may be placed inside the tubular ceramic support. The mixture of gases may be supplied by an industrial process such as the mixture of exhaust gases from the IGCC process. 9 figs.

Collins, J.P.; Way, J.D.

1997-07-29T23:59:59.000Z

111

Hydrogen-Selective Membrane  

SciTech Connect

A hydrogen-selective membrane comprises a tubular porous ceramic support having a palladium metal layer deposited on an inside surface of the ceramic support. The thickness of the palladium layer is greater than about 10 .mu.m but typically less than about 20 .mu.m. The hydrogen permeation rate of the membrane is greater than about 1.0 moles/m.sup.2.s at a temperature of greater than about 500.degree. C. and a transmembrane pressure difference of about 1,500 kPa. Moreover, the hydrogen-to-nitrogen selectivity is greater than about 600 at a temperature of greater than about 500.degree. C. and a transmembrane pressure of about 700 kPa. Hydrogen can be separated from a mixture of gases using the membrane. The method may include the step of heating the mixture of gases to a temperature of greater than about 400.degree. C. and less than about 1000.degree. C. before the step of flowing the mixture of gases past the membrane. The mixture of gases may include ammonia. The ammonia typically is decomposed to provide nitrogen and hydrogen using a catalyst such as nickel. The catalyst may be placed inside the tubular ceramic support. The mixture of gases may be supplied by an industrial process such as the mixture of exhaust gases from the IGCC process.

Collins, John P. (Boulder, CO); Way, J. Douglas (Boulder, CO)

1995-09-19T23:59:59.000Z

112

Hydrogen-selective membrane  

DOE Patents (OSTI)

A hydrogen-selective membrane comprises a tubular porous ceramic support having a palladium metal layer deposited on an inside surface of the ceramic support. The thickness of the palladium layer is greater than about 10 .mu.m but typically less than about 20 .mu.m. The hydrogen permeation rate of the membrane is greater than about 1.0 moles/m.sup.2. s at a temperature of greater than about 500.degree. C. and a transmembrane pressure difference of about 1,500 kPa. Moreover, the hydrogen-to-nitrogen selectivity is greater than about 600 at a temperature of greater than about 500.degree. C. and a transmembrane pressure of about 700 kPa. Hydrogen can be separated from a mixture of gases using the membrane. The method may include the step of heating the mixture of gases to a temperature of greater than about 400.degree. C. and less than about 1000.degree. C. before the step of flowing the mixture of gases past the membrane. The mixture of gases may include ammonia. The ammonia typically is decomposed to provide nitrogen and hydrogen using a catalyst such as nickel. The catalyst may be placed inside the tubular ceramic support. The mixture of gases may be supplied by an industrial process such as the mixture of exhaust gases from the IGCC process.

Collins, John P. (Boulder, CO); Way, J. Douglas (Boulder, CO)

1997-01-01T23:59:59.000Z

113

Hydrogen-selective membrane  

DOE Patents (OSTI)

A hydrogen-selective membrane comprises a tubular porous ceramic support having a palladium metal layer deposited on an inside surface of the ceramic support. The thickness of the palladium layer is greater than about 10 {micro}m but typically less than about 20 {micro}m. The hydrogen permeation rate of the membrane is greater than about 1.0 moles/m{sup 2}s at a temperature of greater than about 500 C and a transmembrane pressure difference of about 1,500 kPa. Moreover, the hydrogen-to-nitrogen selectivity is greater than about 600 at a temperature of greater than about 500 C and a transmembrane pressure of about 700 kPa. Hydrogen can be separated from a mixture of gases using the membrane. The method may include the step of heating the mixture of gases to a temperature of greater than about 400 C and less than about 1000 C before the step of flowing the mixture of gases past the membrane. The mixture of gases may include ammonia. The ammonia typically is decomposed to provide nitrogen and hydrogen using a catalyst such as nickel. The catalyst may be placed inside the tubular ceramic support. The mixture of gases may be supplied by an industrial process such as the mixture of exhaust gases from the IGCC process. 9 figs.

Collins, J.P.; Way, J.D.

1995-09-19T23:59:59.000Z

114

Range Selectivity Estimation for Continuous Attributes  

E-Print Network (OSTI)

Many commercial database systems maintain histograms to efficiently estimate query selectivities as part of query optimization. Most work on histogram design is implicitly geared towards discrete or categorical attribute value domains. In this paper, we consider approaches that are better suited for the continuous valued attributes commonly found in scientific and statistical databases. We propose two methods based on spline functions for estimating the selectivity of range queries over univariate and multivariate data. These methods are more accurate than histograms. As the results from our experiments on both real and synthetic data sets demonstrate, the proposed methods achieved substantially better (up to 5.5 times) estimation error than the state-of-the-art histograms, at exactly the same storage space and with comparable CPU runtime overhead; moreover, the superiority of the proposed spline methods is amplified when applied to multivariate data. 1 Introduction Selectivity esti...

Flip Korn; Theodore Johnson; H. V. Jagadish

1999-01-01T23:59:59.000Z

115

Query Selectivity Estimation for Uncertain Data  

E-Print Network (OSTI)

Abstract. Applications requiring the handling of uncertain data have led to the development of database management systems extending the scope of relational databases to include uncertain (probabilistic) data as a native data type. New automatic query optimizations having the ability to estimate the cost of execution of a given query plan, as available in existing databases, need to be developed. For probabilistic data this involves providing selectivity estimations that can handle multiple values for each attribute and also new query types with threshold values. This paper presents novel selectivity estimation functions for uncertain data and shows how these functions can be integrated into PostgreSQL to achieve query optimization for probabilistic queries over uncertain data. The proposed methods are able to handle both attribute- and tuple-uncertainty. Our experimental results show that our algorithms are efficient and give good selectivity estimates with low space-time overhead. 1

Sarvjeet Singh; Chris Mayfield; Rahul Shah; Sunil Prabhakar; Susanne Hambrusch

2008-01-01T23:59:59.000Z

116

Minimising the delta test for variable selection in regression problems  

Science Conference Proceedings (OSTI)

The problem of selecting an adequate set of variables from a given data set of a sampled function becomes crucial by the time of designing the model that will approximate it. Several approaches have been presented in the literature although recent studies ... Keywords: FBS, GAs, delta test, forward-backward search, genetic algorithms, hybrid algorithms, parallel architectures, regression problems, tabu search, variable selection

Alberto Guillen; Dusan Sovilj; Amaury Lendasse; Fernando Mateo; Ignacio Rojas

2008-03-01T23:59:59.000Z

117

Selected State Legislation and  

Gasoline and Diesel Fuel Update (EIA)

170 170 Energy Information Administration/Assumptions to the Annual Energy Outlook 2009 Appendix A: Handling of Federal and Selected State Legislation and Regulation in the Annual Energy Outlook Legislation Brief Description AEO Handling Basis Residential Sector A. National Appliance Energy Conservation Act of 1987 Requires Secretary of Energy to set minimum efficiency standards for 10 appliance categories. Included for categories represented in the AEO residential sector forecast. a. Room Air Conditioners Current standard of 9.8 EER Federal Register Notice of Final Rulemaking. b. Other Air Conditioners (<5.4 tons) Current standard 10 SEET for central air conditioners and heat pumps, increasing to 13 SEER in 2006. Federal Register Notice of Final Rulemaking.

118

Selective Enumeration A Formal Definition  

E-Print Network (OSTI)

Selective Enumeration A Formal Definition Craig A. Damon January, 1998 CMU­CS­98­104 School, specification checking, constraint satisfaction. #12; Abstract Selective enumeration is a method for reducing. This paper gives a formal definition of selective enumeration and using that definition, proves soundness

119

Minimum Description Length Model Selection  

E-Print Network (OSTI)

Minimum Description Length Model Selection Problems and Extensions Steven de Rooij #12;#12;Minimum Description Length Model Selection Problems and Extensions #12;ILLC Dissertation Series DS-2008-07 For further-mail: illc@science.uva.nl homepage: http://www.illc.uva.nl/ #12;Minimum Description Length Model Selection

120

Selective Enumeration Craig A. Damon  

E-Print Network (OSTI)

Selective Enumeration Craig A. Damon July 2000 CMU­CS­00­151 School of Computer Science Computer; iii Abstract Selective enumeration is an approach to pruning search trees with the goal of preventing tractable. This dissertation demonstrates that selective enumeration enables an analysis of formal

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Analyzing Regression Test Selection Techniques  

Science Conference Proceedings (OSTI)

Abstract¿Regression testing is a necessary but expensive maintenance activity aimed at showing that code has not been adversely affected by changes. Regression test selection techniques reuse tests from an existing test suite to test a modified program. ... Keywords: Software maintenance, regression testing, selective retest, regression test selection.

Gregg Rothermel; Mary Jean Harrold

1996-08-01T23:59:59.000Z

122

Livermore retiree selected as finalist in international contest...  

National Nuclear Security Administration (NNSA)

students. And now his time has paid off. He has been selected as a finalist in the 2013 Flame Challenge, an international contest that asks scientists to communicate complex...

123

Hybridization and Selective Release of DNA Microarrays  

SciTech Connect

DNA microarrays contain sequence specific probes arrayed in distinct spots numbering from 10,000 to over 1,000,000, depending on the platform. This tremendous degree of multiplexing gives microarrays great potential for environmental background sampling, broad-spectrum clinical monitoring, and continuous biological threat detection. In practice, their use in these applications is not common due to limited information content, long processing times, and high cost. The work focused on characterizing the phenomena of microarray hybridization and selective release that will allow these limitations to be addressed. This will revolutionize the ways that microarrays can be used for LLNL's Global Security missions. The goals of this project were two-fold: automated faster hybridizations and selective release of hybridized features. The first study area involves hybridization kinetics and mass-transfer effects. the standard hybridization protocol uses an overnight incubation to achieve the best possible signal for any sample type, as well as for convenience in manual processing. There is potential to significantly shorten this time based on better understanding and control of the rate-limiting processes and knowledge of the progress of the hybridization. In the hybridization work, a custom microarray flow cell was used to manipulate the chemical and thermal environment of the array and autonomously image the changes over time during hybridization. The second study area is selective release. Microarrays easily generate hybridization patterns and signatures, but there is still an unmet need for methodologies enabling rapid and selective analysis of these patterns and signatures. Detailed analysis of individual spots by subsequent sequencing could potentially yield significant information for rapidly mutating and emerging (or deliberately engineered) pathogens. In the selective release work, optical energy deposition with coherent light quickly provides the thermal energy to single spots to release hybridized DNA. This work leverages LLNL expertise in optics, microfluids, and bioinformatics.

Beer, N R; Baker, B; Piggott, T; Maberry, S; Hara, C M; DeOtte, J; Benett, W; Mukerjee, E; Dzenitis, J; Wheeler, E K

2011-11-29T23:59:59.000Z

124

Selective methane oxidation over promoted oxide catalysts  

DOE Green Energy (OSTI)

Objective was to selectively oxidize methane to C{sub 2} hydrocarbons and to oxygenates, in particular formaldehyde and methanol, in high space time yields under relatively mild reaction conditions. Results in this document are reported under the headings: methane oxidation over silica, methane oxidation over Sr/La{sub 2}O{sub 3} catalysts, and oxidative coupling of methane over sulfate-doped Sr/La{sub 2}O{sub 3} catalysts. 24 refs, 10 figs, 4 tabs.

Klier, K.; Herman, R.G.

1993-12-31T23:59:59.000Z

125

Monitoring Selective Logging in Tropical Evergreen Forests Using Landsat: Multitemporal Regional Analyses in Mato Grosso, Brazil  

Science Conference Proceedings (OSTI)

Selective logging degrades tropical forests. Logging operations vary in timing, location, and intensity. Evidence of this land use is rapidly obscured by forest regeneration and ongoing deforestation. A detailed study of selective logging ...

Eraldo A. T. Matricardi; David L. Skole; Mark A. Cochrane; Jiaguo Qi; Walter Chomentowski

2005-11-01T23:59:59.000Z

126

Reduction in maximum time uncertainty of paired time signals  

DOE Patents (OSTI)

Reduction in the maximum time uncertainty (t/sub max/ - t/sub min/) of a series of paired time signals t/sub 1/ and t/sub 2/ varying between two input terminals and representative of a series of single events where t/sub 1/ less than or equal to t/sub 2/ and t/sub 1/ + t/sub 2/ equals a constant, is carried out with a circuit utilizing a combination of OR and AND gates as signal selecting means and one or more time delays to increase the minimum value (t/sub min/) of the first signal t/sub 1/ closer to t/sub max/ and thereby reduce the difference. The circuit may utilize a plurality of stages to reduce the uncertainty by factors of 20 to 800.

Theodosiou, G.E.; Dawson, J.W.

1981-02-11T23:59:59.000Z

127

Selecting the right flowmeter  

Science Conference Proceedings (OSTI)

The miles of piping found in chemical process and utility areas are visible evidence of the importance of moving fluids safely and efficiently in the ongoing quest to improve unit operations. The measurement and control of fluid flow offers often-unrecognized opportunities for improvement, not just in process control, but in the utilization of total plant assets. Potential benefits include improved quality, throughput and uptime, and reduced costs. Innovations in flowmeter technology, driven by the recent shift from analog to microprocessor-based digital circuitry, have dramatically increased the quantity and value of the data provided by flowmeters. The ability to use this information for control purposes will be further facilitated by the advent of the Fieldbus protocol, which will allow instruments to communicate directly with each other, permitting true decentralized, digital control. This article offers an evaluation process to help you narrow down your options. First, the author identifies the many factors affecting the selection of flowmeters for different types of service, then they review various concepts of flow measurement and many of the factors that influence fluid flow. Several of the most common technologies, including the newest developments, will be discussed along with their advantages and limitations. Finally, they look at how the communication and computing advances taking place in field devices will impact the ability to manage plant assets for the continuous improvement of quality, uptime, throughput, safety and return-on-investment.

Pomroy, J. [Fisher-Rosemount, Eden Prairie, MN (United States). Rosemount Measurement Div.

1996-05-01T23:59:59.000Z

128

Neutrino mass sensitivity by MAC-E-Filter based time-of-flight spectroscopy with the example of KATRIN  

E-Print Network (OSTI)

The KATRIN experiment aims at a measurement of the neutrino mass with a 90 % C.L. sensitivity of 0.2 eV/c$^2$ by measuring the endpoint region of the tritium $\\beta$ decay spectrum from a windowless gaseous molecular tritium source using an integrating spectrometer of the MAC-E-Filter type. We discuss the idea of using the MAC-E-Filter in a time-of-flight mode (MAC-E-TOF) in which the neutrino mass is determined by a measurement of the electron time-of-flight (TOF) spectrum that depends on the neutrino mass. MAC-E-TOF spectroscopy here is a very sensitive method since the $\\beta$-electrons are slowed down to distinguishable velocities by the MAC-E-Filter. Their velocity depends strongly on their surplus energy above the electric retarding potential. Using MAC-E-TOF, a statistical sensitivity gain is expected. Because a small number of retarding-potential settings is sufficient for a complete measurement, in contrast to about 40 different retarding potentials used in the standard MAC-E-Filter mode, there is a gain in measurement time and hence statistical power. The improvement of the statistical uncertainty of the squared neutrino mass has been determined by Monte Carlo simulation to be a factor 5 for an ideal case neglecting background and timing uncertainty. Additionally, two scenarios to determine the time-of-flight of the $\\beta$-electrons are discussed, which use the KATRIN detector for creating the stop signal and different methods for obtaining a start signal. These comprise the hypothetical case of an `electron tagger' which detects passing electrons with minimal interference and the more realistic case of `gated filtering', where the electron flux is periodically cut off by pulsing the pre-spectrometer potential.

Nicholas Steinbrink; Volker Hannen; Eric L. Martin; R. G. Hamish Robertson; Michael Zacher; Christian Weinheimer

2013-08-02T23:59:59.000Z

129

Neutrino mass sensitivity by MAC-E-Filter based time-of-flight spectroscopy with the example of KATRIN  

E-Print Network (OSTI)

The KArlsruhe TRItium Neutrino (KATRIN) experiment aims at a measurement of the neutrino mass with a 90 % confidence limit (C.L.) sensitivity of 0.2 eV/c$^2$ by measuring the endpoint region of the tritium $\\beta$ decay spectrum from a windowless gaseous molecular tritium source using an integrating spectrometer of the MAC-E-Filter type. We discuss the idea of using the MAC-E-Filter in a time-of-flight mode (MAC-E-TOF) in which the neutrino mass is determined by a measurement of the electron time-of-flight (TOF) spectrum that depends on the neutrino mass. MAC-E-TOF spectroscopy here is a very sensitive method since the $\\beta$-electrons are slowed down to distinguishable velocities by the MAC-E-Filter. Their velocity depends strongly on their surplus energy above the electric retarding potential. Using MAC-E-TOF, a statistical sensitivity gain is expected. Because a small number of retarding-potential settings is sufficient for a complete measurement, in contrast to about 40 different retarding potentials used in the standard MAC-E-Filter mode, there is a gain in measurement time and hence statistical power. The improvement of the statistical uncertainty of the squared neutrino mass has been determined by Monte Carlo simulation to be a factor 5 for an ideal case neglecting background and timing uncertainty. Additionally, two scenarios to determine the time-of-flight of the $\\beta$-electrons are discussed, which use the KATRIN detector for creating the stop signal and different methods for obtaining a start signal. These comprise the hypothetical case of an `electron tagger' which detects passing electrons with minimal interference and the more realistic case of `gated filtering', where the electron flux is periodically cut off by pulsing the pre-spectrometer potential.

Nicholas Steinbrink; Volker Hannen; Eric L. Martin; R. G. Hamish Robertson; Michael Zacher; Christian Weinheimer

2013-08-02T23:59:59.000Z

130

2002 HBCU Selections.doc  

NLE Websites -- All DOE Office Websites (Extended Search)

seeks to select a proper transportation phase that meets the requirement of both increase of absorption rate and transportation of CO2 into the carrying phase. DOE share:...

131

CQ - Code selection through query.  

E-Print Network (OSTI)

??This thesis proposes a query language for code selection. It is designed to work on virtual machine based languages and is intended to be used… (more)

ZENZARO, SIMONE

2010-01-01T23:59:59.000Z

132

Time and Frequency Portal  

Science Conference Proceedings (OSTI)

NIST Home > Time and Frequency Portal. Time and Frequency Portal. Programs and Projects. CODATA values of the fundamental constants ...

2013-06-27T23:59:59.000Z

133

Time Series and Forecasting  

Science Conference Proceedings (OSTI)

Time Series and Forecasting. Leigh, Stefan and Perlman, S. (1991). "An Index for Comovement of Time Sequences With ...

134

Site Selection Process | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Site Selection Process Site Selection Process SiteSelectionProcess.pdf More Documents & Publications dgappendices.pdf REAL ESTATE PROCESS OPAM Policy Acquisition Guides...

135

Manufacturing technology selection: a supply chain perspective.  

E-Print Network (OSTI)

??This thesis describes a technology selection framework for manufacturing technology selection. Technology selection has been identified as a major area of decision making in a… (more)

Farooq, Sami

2007-01-01T23:59:59.000Z

136

Comonotonic approximations for optimal portfolio selection problems  

E-Print Network (OSTI)

We investigate multiperiod portfolio selection problems in a Black & Scholes type market where a basket of 1 riskfree and m risky securities are traded continuously. We look for the optimal allocation of wealth within the class of ’constant mix ’ portfolios. First, we consider the portfolio selection problem of a decision maker who invests money at predetermined points in time in order to obtain a target capital at the end of the time period under consideration. A second problem concerns a decision maker who invests some amount of money (the initial wealth or provision) in order to be able to fullfil a series of future consumptions or payment obligations. Several optimality criteria and their interpretation within Yaari’s dual theory of choice under risk are presented. For both selection problems, we propose accurate approximations based on the concept of comonotonicity, as studied in Dhaene, Denuit, Goovaerts, Kaas & Vyncke (2002 a,b). Our analytical approach avoids simulation, and hence reduces the computing effort drastically. 1

J. Dhaene; S. Vanduffel; M. J. Goovaerts; R. Kaas; D. Vyncke

2005-01-01T23:59:59.000Z

137

The Nature and Origin of Time-asymmetric Spacetime Structures  

E-Print Network (OSTI)

Time-asymmetric spacetime structures, in particular those representing black holes and the expansion of the universe, are intimately related to other arrows of time, such as the second law and the retardation of radiation. The nature of the quantum arrow, often attributed to a collapse of the wave function, is essential, in particular, for understanding the much discussed "black hole information loss paradox". This paradox assumes a new form and can possibly be avoided in a consistent causal treatment that may be able to avoid horizons and singularities. The master arrow that would combine all arrows of time does not have to be identified with a direction of the formal time parameter that serves to formulate the dynamics as a succession of global states (a trajectory in configuration or Hilbert space). It may even change direction with respect to a fundamental physical clock such as the cosmic expansion parameter if this was formally extended either into a future contraction era or to negative "pre-big-bang" values.

H. D. Zeh

2010-12-21T23:59:59.000Z

138

Selecting windows for energy efficiency  

SciTech Connect

New window technologies have increased energy benefits and comfort, and have provided more practical options for consumers. This selection guide will help homeowners, architects, and builders take advantage of the expanding window market. The guide contains three sections: an explanation of energy-related window characteristics, a discussion of window energy performance ratings, and a convenient checklist for window selection.

1997-05-01T23:59:59.000Z

139

Real-time MSE measurements for current profile control on KSTAR  

SciTech Connect

To step up from current day fusion experiments to power producing fusion reactors, it is necessary to control long pulse, burning plasmas. Stability and confinement properties of tokamak fusion reactors are determined by the current or q profile. In order to control the q profile, it is necessary to measure it in real-time. A real-time motional Stark effect diagnostic is being developed at Korean Superconducting Tokamak for Advanced Research for this purpose. This paper focuses on 3 topics important for real-time measurements: minimize the use of ad hoc parameters, minimize external influences and a robust and fast analysis algorithm. Specifically, we have looked into extracting the retardance of the photo-elastic modulators from the signal itself, minimizing the influence of overlapping beam spectra by optimizing the optical filter design and a multi-channel, multiharmonic phase locking algorithm.

De Bock, M. F. M.; Aussems, D.; Huijgen, R.; Scheffer, M. [Eindhoven University of Technology, Eindhoven (Netherlands); Chung, J. [National Fusion Research Institute, Daejeon (Korea, Republic of)

2012-10-15T23:59:59.000Z

140

ARPA-E Project Selections  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Project Selections Project Selections September 23, 2010 These projects have been selected for negotiation of awards; final award amounts may vary. Lead Research Organization (Partner Organizations) Amount Lead Organization Location (City, State) Technology Focus - Application: Project Title Project Description 1) Innovative Cybersecurity Solutions Grid Protection Alliance (University of Illinois, Pacific Northwest National Laboratory, PJM Interconnection, AREVA T&D) $3,215,000 Chattanooga, TN SIEGate: Secure Information Exchange for Electric Grid Operations The Grid Protection Alliance will research, develop, and commercialize a Secure Information Exchange Gateway (SIEGate) that provides secure communication of data between control centers.

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Classical and dominance-based rough sets in the search for genes under balancing selection  

Science Conference Proceedings (OSTI)

Since the time of Kimura’s theory of neutral evolution at molecular level the search for genes under natural selection is one of the crucial problems in population genetics. There exists quite a number of statistical tests designed for it, however, ... Keywords: ATM, BLM, RECQL, WRN, balancing selection, classical rough sets approach, dominance-based rough sets approach, natural selection, neutrality tests

Krzysztof A. Cyran

2010-01-01T23:59:59.000Z

142

Operation and Maintenance Guidelines for Selective Catalytic Reduction Systems  

Science Conference Proceedings (OSTI)

Timely and proper execution of operation and maintenance (O&M) activities may be a key factor in ensuring the successful function of selective catalytic reduction (SCR) systems. This report serves as the 2012 update of EPRI’s Operation and Maintenance Guidelines for Selective Catalytic Reduction Systems, originally published in 2001 and updated annually. New and revised content this year includes: 1) recent developments in in situ NOx analyzers, including a ...

2012-12-05T23:59:59.000Z

143

Measured Performance of Selective Glazings  

NLE Websites -- All DOE Office Websites (Extended Search)

Measured Performance of Selective Glazings Measured Performance of Selective Glazings Title Measured Performance of Selective Glazings Publication Type Conference Paper LBNL Report Number LBL-37747 Year of Publication 1995 Authors Klems, Joseph H., Mehry Yazdanian, and Guy O. Kelley Conference Name Thermal Performance of the Exterior Envelopes of Buildings VI Conference Date Published 12/1995 Conference Location Clearwater Beach, FL Call Number LBL-37747 Abstract Measurements of the net heat flow through four selective glazings in comparison with clear double glazing under late summer outdoor conditions are presented. The solar heat gain coefficient (SHGC) for each glazing is extracted from the data and shown to be angle-dependent. Good agreement is found between measured properties and calculations with WINDOW 4.1.

144

Maps of Selected State Subdivisions  

Gasoline and Diesel Fuel Update (EIA)

Crude Oil, Natural Gas, and Natural Gas Liquids Proved Reserves Summary Maps of Selected State Subdivisions Map 1: Alaska Map 2: California Map 3: Louisiana Map 4: New Mexico Map...

145

Select Solar | Open Energy Information  

Open Energy Info (EERE)

Select Solar Select Solar Jump to: navigation, search Logo: Select Solar Name Select Solar Address Unit 5 Blakehill Business Park Chelworth Road Cricklade SN6 6JD Place Cricklade, United Kingdom Sector Solar Year founded 2002 Phone number 0845 0031353 Website http://www.selectsolar.co.uk/ Coordinates 51.6393949°, -1.8573671° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":51.6393949,"lon":-1.8573671,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

146

Hydrogen Selective Exfoliated Zeolite Membranes  

NLE Websites -- All DOE Office Websites (Extended Search)

Hydrogen Selective Exfoliated Zeolite Hydrogen Selective Exfoliated Zeolite Membranes Background An important component of the Department of Energy (DOE) Carbon Sequestration Program is the development of carbon capture technologies for power systems. Capturing carbon dioxide (CO 2 ) from mixed-gas streams is a first and critical step in carbon sequestration. To be technically and economically viable, a successful separation method must be applicable to industrially relevant gas streams at realistic

147

Compiling for time predictability  

Science Conference Proceedings (OSTI)

Within the T-CREST project we work on hardware/software architectures and code-generation strategies for time-predictable embedded and cyber-physical systems. In this paper we present the single-path code generation approach that we plan to explore and ... Keywords: compilers, real-time systems, time predictability, worst-case execution-time analysis

Peter Puschner; Raimund Kirner; Benedikt Huber; Daniel Prokesch

2012-09-01T23:59:59.000Z

148

Certifying execution time  

Science Conference Proceedings (OSTI)

In this paper we present the framework Abstraction-Carrying CodE Platform for Timing validation (ACCEPT), designed for timing analysis of embedded real-time systems using the worst-case execution time (WCET) as the safety parameter. In the context ...

Vítor Rodrigues; João Pedro Pedroso; Mário Florido; Simão Melo de Sousa

2011-05-01T23:59:59.000Z

149

Time-Resolved  

NLE Websites -- All DOE Office Websites (Extended Search)

Time-Resolved Time-Resolved Time-Resolved Print Of the four fundamental parameters that we use to perceive the physical world (energy, momentum, position, and time) three correspond to the three broad categories of synchrotron experimental measurement techniques: spectroscopy (energy), scattering (momentum), and imaging (position). The fourth parameter-time-can in principle be applied to all the techniques. At the ALS, many experiments can be carried out in real time, with data being recorded from the same sample as it changes over time. Some time-resolved experiments take advantage of the pulsed nature of the ALS's synchrotron radiation, which, like a strobe light, can capture a series of "snapshots" of a process that, when viewed sequentially, show us how a given process evolves over time. Other experiments simply require two pulses: one to "pump" energy into the sample system and a second to probe the system's excited state.

150

General Transformations of Space and Time according to Aether Theory  

E-Print Network (OSTI)

Assuming the existence of a preferred aether frame and the anisotropy of the one-way speed of light in platforms different from the aether frame, we derive the space and time transformations relative to bodies moving in any direction of space and not only in the direction of the common x-axis of the co-ordinate systems under consideration. Taking for granted length contraction and clock retardation, we show that the experimental space-time transformations result from measurement distortions due to the fact that the length of the rods and the frequency of the clocks, used for the measure, do not have a constant value as a result of their motion through the aether, and because the standard synchronization procedures are affected by a synchronism discrepancy effect. When the motion of bodies is aligned along the common x-axis, the transformations assume the same mathematical form as the conventional transformations. However, their meaning is quite different because they have been derived on the basis of very different assumptions, and they arise from the measurement distortions mentioned above. Therefore they conceal hidden variables which are the true transformations.

Joseph Levy

2010-03-09T23:59:59.000Z

151

Method for discriminative particle selection  

DOE Patents (OSTI)

The invention is a method and means for separating ions or providing an ion beam. The invention generates ions of the isotopes to be separated, and then provides a traveling electric potential hill created by a sequential series of quasi static electric potential hills. By regulating the velocity and potential amplitude of the traveling electric potential hill ionized isotopes are selectively positively or negatively accelerated. Since the ionized isotopes have differing final velocities, the isotopes may be collected separately or used to produce an ion beam of a selected isotope.

Post, Richard F. (Walnut Creek, CA)

1992-01-01T23:59:59.000Z

152

The Economics of Cogeneration Selection  

E-Print Network (OSTI)

The design and choice of a specific cogeneration system is a process of selecting and deciding from numerous alternatives, including the option not to cogenerate. The final system specification is in reality the result of an extensive tradeoff analysis. The reason for performing a thorough tradeoff analysis is to design a cogeneration system that will meet or surpass stated technical, operational and economic criteria. This paper outlines the steps necessary to select the preferred cogeneration system through the use of standard economic evaluation techniques.

Fisk, R. W.; Hall, E. W.; Sweeney, J. H.

1985-05-01T23:59:59.000Z

153

Managing time, part 2  

Science Conference Proceedings (OSTI)

Masterful time management means not just tracking of messages in your personal environment, but managing your coordination network with others.

Peter J. Denning; Ritu Raj

2011-09-01T23:59:59.000Z

154

FREQUENCY AND TIME  

Science Conference Proceedings (OSTI)

... STRATWARM observed and FLARES expected ... observed and PROTON FLARE expected (- - ) STRATWARM ... time of observed solar or geophysical ...

2003-01-30T23:59:59.000Z

155

QuickTime VR  

Science Conference Proceedings (OSTI)

QuickTime VR. Christine Piatko and Sandy Ressler. ... Sandy Ressler's Office. Plant Floor of Black & Decker in Fayetteville NC. ...

156

FINAL REPORT SELECTION OF RADIONUCLIDES FOR  

E-Print Network (OSTI)

FINAL REPORT SELECTION OF RADIONUCLIDES FOR INCLUSION IN DOSE RECONSTRUCTIONS AT IDAHO NATIONAL Author: David C. Kocher SENES Oak Ridge, Inc. July 2005 #12;Selection of Radionuclides July 2005..................................................................................2 3.0 Selection of Radionuclides by Screening

157

Timed Property Sequence Chart  

Science Conference Proceedings (OSTI)

Property Sequence Chart (PSC) is a novel scenario-based notation, which has been recently proposed to represent temporal properties of concurrent systems. This language balances expressive power and simplicity of use. However, the current version of ... Keywords: Property Sequence Chart, Real-time specification patterns, Timed Property Sequence Chart, Timing properties

Pengcheng Zhang; Bixin Li; Lars Grunske

2010-03-01T23:59:59.000Z

158

Noncommutative Two Time Physics  

E-Print Network (OSTI)

We present a classical formalism describing two-time physics with Abelian canonical gauge field backgrounds. The formalism can be used as a starting point for the construction of an interacting quantized two-time physics theory in a noncommutative soace-time.

W. Chagas-Filho

2006-04-03T23:59:59.000Z

159

Ambient noise levels and reverberation times in Mississippi school rooms  

Science Conference Proceedings (OSTI)

Nine elementary school classrooms at three Mississippi public schools were selected at random for noise and reverberation time measures to monitor voluntary compliance with ANSI standard S12.60-2002 (Acoustical Performance Criteria

Edward L. Goshorn; Brett E. Kemker

2012-01-01T23:59:59.000Z

160

On the signal bounding problem in timing analysis  

Science Conference Proceedings (OSTI)

In this paper, we study the propagation of slew dependent bounding signals and the corresponding slew problem in static timing analysis. The selection of slew from the latest arriving signal, a commonly used strategy, may violate the rule of monotonic ...

Jin Fuw Lee; D. L. Ostapko; Jeffery Soreff; C. K. Wong

2001-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Quantum Operation Time Reversal  

E-Print Network (OSTI)

The dynamics of an open quantum system can be described by a quantum operation, a linear, complete positive map of operators. Here, I exhibit a compact expression for the time reversal of a quantum operation, which is closely analogous to the time reversal of a classical Markov transition matrix. Since open quantum dynamics are stochastic, and not, in general, deterministic, the time reversal is not, in general, an inversion of the dynamics. Rather, the system relaxes towards equilibrium in both the forward and reverse time directions. The probability of a quantum trajectory and the conjugate, time reversed trajectory are related by the heat exchanged with the environment.

Crooks, Gavin E

2007-01-01T23:59:59.000Z

162

Quantum Operation Time Reversal  

E-Print Network (OSTI)

The dynamics of an open quantum system can be described by a quantum operation, a linear, complete positive map of operators. Here, I exhibit a compact expression for the time reversal of a quantum operation, which is closely analogous to the time reversal of a classical Markov transition matrix. Since open quantum dynamics are stochastic, and not, in general, deterministic, the time reversal is not, in general, an inversion of the dynamics. Rather, the system relaxes towards equilibrium in both the forward and reverse time directions. The probability of a quantum trajectory and the conjugate, time reversed trajectory are related by the heat exchanged with the environment.

Gavin E. Crooks

2007-06-26T23:59:59.000Z

163

Selecting a new water heater  

SciTech Connect

This fact sheet describes the types of water heaters available (storage water heaters, demand water heaters, heat pump water heaters, tankless coil and indirect water heaters, and solar water heaters). The criteria for selection are discussed. These are capacity, efficiency rating, and cost. A resource list is provided for further information.

NONE

1995-03-01T23:59:59.000Z

164

Preparation of gas selective membranes  

DOE Patents (OSTI)

Gas separation membranes which possess improved characteristics as exemplified by selectivity and flux may be prepared by coating a porous organic polymer support with a solution or emulsion of a plasticizer and an organic polymer, said coating being effected at subatmospheric pressures in order to increase the penetration depth of the coating material.

Kulprathipanja, S.; Kulkarni, S.S.; Funk, E.W.

1988-06-14T23:59:59.000Z

165

Our Process of Paper Selection - CECM  

E-Print Network (OSTI)

Each of the papers in this volume has been selected because the authors are ` well-known', and their reputation was a significant factor in this selection process.

166

Small businesses selected for nuclear waste services  

NLE Websites -- All DOE Office Websites (Extended Search)

Small businesses selected for nuclear waste services Small businesses selected for nuclear waste clean-up services Northern New Mexico businesses compete for up to 200 million in...

167

On the Time Times Temperature Bound  

E-Print Network (OSTI)

Recently Hod proposes a lower bound on the relaxation time of a perturbed thermodynamic system. For gravitational systems this bound transforms into a condition on the fundamental quasinormal frequency. We test the bound in some spacetimes whose quasinormal frequencies are calculated exactly, as the three-dimensional BTZ black hole, the D-dimensional de Sitter spacetime, and the D-dimensional Nariai spacetime. We find that for some of these spacetimes their fundamental quasinormal frequencies do not satisfy the bound proposed by Hod.

A. Lopez-Ortega

2010-06-28T23:59:59.000Z

168

A shader based adaptation of selected sixteenth century maps  

E-Print Network (OSTI)

This research develops a technique focused on shading and texturing, with an emphasis on line work and color, to emulate the unique qualities of copperplate line-engraving from 16th century cartography. A visual analysis of selected maps determines the defining characteristics adapted for three-dimensional computer generated environments. The resulting work is presented in a short time-based animation.

Haque, Shaila Sabrina

2008-05-01T23:59:59.000Z

169

Recycling and Disposal of Spent Selective Catalytic Reduction Catalyst  

Science Conference Proceedings (OSTI)

Selective catalytic reduction (SCR) technology has become widespread within the utility industry as a means of controlling emissions of nitrogen oxides (NOx). The technology uses a solid catalyst that deactivates over time; and thus significant volumes of catalyst will need regeneration, recycle, or disposal. This study examined issues related to spent catalyst recycle and disposal.

2003-11-12T23:59:59.000Z

170

What Time is It?  

Science Conference Proceedings (OSTI)

... These are sometimes marketed as "atomic clocks", but ... problems include incorrectly setting your local time zone on the clock, batteries that need ...

2011-01-19T23:59:59.000Z

171

Carlsbad Field Office Manager Selected  

NLE Websites -- All DOE Office Websites (Extended Search)

Carlsbad Field Office Manager Selected CARLSBAD, N.M., November 10, 2011 - The U.S. Department of Energy's (DOE) Richland Operations Office (RL) Assistant Manager for the River Corridor Joe Franco was selected as Manager for the Carlsbad Field Office (CBFO), which oversees the Waste Isolation Pilot Plant (WIPP). CBFO Deputy Manager Ed Ziemianski has been acting in the CBFO Manager's position for the past year and will continue to serve as Deputy Manager. In operation since 1999, WIPP is a DOE facility designed to safely isolate defense-related transuranic (TRU) waste from people and the environment. Since 2006, Franco was responsible for cleanup and restoration of the 220 square miles of the

172

JGI - Len Pennacchio - Select Publications  

NLE Websites -- All DOE Office Websites (Extended Search)

Len Pennacchio - Select Publications Len Pennacchio - Select Publications Graduate Studies Pennacchio, L. A., Lehesjoki, A.-E., Stone, N. E., Willour, V., Virtaneva, K., Miao, J., D'Amato, E., Ramirez, L., Faham, M., Koskiniemi, M., Warrington, J., Norio, R., A., de la Chapelle, A., Cox, D. R. and Myers, R. M. 1996. Mutations in the gene encoding cystatin B in Progressive Myoclonus Epilepsy (EPM1). Science 271(5256): 1731-1734. Virtaneva, K., D'Amato, E., Miao, J., Koskiniemi, M., Norio, R., Avanzini, G., Franceschetti, S., Michelucci, R., Tassinari, C. A., Omer, S., Pennacchio, L. A., Myers, R. M., Dieguez-Lucena, J. L., Krahe, R., de la Chapelle, A., and Lehesjoki, A.-E. 1997. Unstable minisatellite expansion causing recessive myoclonus epilepsy (EPM1). Nature Genetics 15(4): 393-396. Pennacchio, L. A., Bouley, D. M., Higgins, K. M., Scott, M. P., Noebels, J.

173

Selection Criteria for Demonstration Projects  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Selection Criteria: Selection Criteria: Energy Savings: * If a building were to apply this technology, how much energy could it save compared to a "typical" existing building? How much energy could it save compared to a typical "new" building built to the latest (IECC 2007) code? Provide references, calculations, and documentation. * If the technology is a drop-in replacement, how much energy could it save compared to "typical" new equipment? Provide references, calculations, and documentation. Market & Job Creation Potential: * What is the market potential for this technology? * What types of buildings is this technology best suited for? What types of buildings is this technology ill-suited for? * How many US buildings that could potentially benefit from/utilize this technology? What % of U.S.

174

Selective methane oxidation over promoted oxide catalysts  

DOE Green Energy (OSTI)

Principal accomplishments have been achieved in all three areas of selective catalytic oxidation of methane that have been pursued in this research project. These accomplishments are centered on the development of catalyst systems that produce high space time yields of C{sub 2} hydrocarbon products, formaldehyde, and methanol from methane/air mixtures at moderate temperatures and at ambient pressure. The accomplishments can be summarized as the following: the SO{sub 4}{sup 2{minus}}/SrO/La{sub 2}O{sub 3} catalyst developed here has been further optimized to produce 2 kg of C{sub 2} hydrocarbons/kg catalyst/hr at 550C; V{sub 2}O{sub 5}SiO{sub 2} catalysts have been prepared that produce up to 1.5 kg formaldehyde/kg catalyst/hr at 630C with CO{sub 2} selectivities; and a novel dual bed catalyst system has been designed and tested that produces over 100 g methanol/kg catalyst/hr at 600C.

Klier, K.; Herman, R.G.

1995-06-01T23:59:59.000Z

175

Selective poly-N-substituted glycine antibiotics  

DOE Patents (OSTI)

Antimicrobial peptoid compounds and related compositions as can be used against bacteria effectively and selectively.

Barron, Annelise E; Czyzewski, Ann M; Dohm, Michelle T; Miller, Tyler M; Zuckermann, Tyler M; Patch, James A; Chongsiriwatana, Nathaniel P

2013-05-21T23:59:59.000Z

176

Stereo matching via selective multiple windows  

E-Print Network (OSTI)

Window-based correlation algorithms are widely used for stereo matching due to their computational efficiency as compared to global algorithms. In this paper, a multiple window correlation algorithm for stereo matching is presented which addresses the problems associated with a fixed window size. The developed algorithm differs from the previous multiple window algorithms by introducing a reliability test to select the most reliable window among multiple windows of increasing sizes. This ensures that at least one window is large enough to cover a region of adequate intensity variations while at the same time small enough to cover a constant depth region. A recursive computation procedure is also used to allow a computationally efficient implementation of the algorithm. The outcome obtained from a standard set of images with known disparity maps shows that the generated disparity maps are more accurate as compared to two popular stereo matching local algorithms.

Satyajit Anil Adhyapak; Nasser Kehtarnavaz; Mihai Nadin

2007-01-01T23:59:59.000Z

177

TIME CALIBRATED OSCILLOSCOPE SWEEP  

DOE Patents (OSTI)

The time calibrator of an electric signal displayed on an oscilloscope is described. In contrast to the conventional technique of using time-calibrated divisions on the face of the oscilloscope, this invention provides means for directly superimposing equal time spaced markers upon a signal displayed upon an oscilloscope. More explicitly, the present invention includes generally a generator for developing a linear saw-tooth voltage and a circuit for combining a high-frequency sinusoidal voltage of a suitable amplitude and frequency with the saw-tooth voltage to produce a resultant sweep deflection voltage having a wave shape which is substantially linear with respect to time between equal time spaced incremental plateau regions occurring once each cycle of the sinusoidal voltage. The foregoing sweep voltage when applied to the horizontal deflection plates in combination with a signal to be observed applied to the vertical deflection plates of a cathode ray oscilloscope produces an image on the viewing screen which is essentially a display of the signal to be observed with respect to time. Intensified spots, or certain other conspicuous indications corresponding to the equal time spaced plateau regions of said sweep voltage, appear superimposed upon said displayed signal, which indications are therefore suitable for direct time calibration purposes.

Owren, H.M.; Johnson, B.M.; Smith, V.L.

1958-04-22T23:59:59.000Z

178

Semantics, experience and time  

Science Conference Proceedings (OSTI)

The computational hypothesis, with its inherent representationalism, and the dynamical hypothesis, with its apparent absence of representations and its commitment to continuous time, stand at an impasse. It is unclear how the dynamical stance can handle ... Keywords: Computation, Experience, Invariance, Semantics, Situatedness, Time

Stephen E. Robbins

2002-09-01T23:59:59.000Z

179

Real-time shading  

Science Conference Proceedings (OSTI)

Real-time procedural shading was once seen as a distant dream. When the first version of this course was offered four years ago, real-time shading was possible, but only with one-of-a-kind hardware or by combining the effects of tens to hundreds of rendering ...

Marc Olano; Kurt Akeley; John C. Hart; Wolfgang Heidrich; Michael McCool; Jason L. Mitchell; Randi Rost

2004-08-01T23:59:59.000Z

180

TIMING OF SHOCK WAVES  

DOE Patents (OSTI)

This patent relates to means for ascertaining the instant of arrival of a shock wave in an exploslve charge and apparatus utilizing this means to coordinate the timing of two operations involving a short lnterval of time. A pair of spaced electrodes are inserted along the line of an explosive train with a voltage applied there-across which is insufficient to cause discharge. When it is desired to initiate operation of a device at the time the explosive shock wave reaches a particular point on the explosive line, the device having an inherent time delay, the electrodes are located ahead of the point such that the ionization of the area between the electrodes caused by the traveling explosive shock wave sends a signal to initiate operation of the device to cause it to operate at the proper time. The operated device may be photographic equipment consisting of an x-ray illuminating tube.

Tuck, J.L.

1955-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Criteria and techniques for field characterization and modeling related to selecting and evaluating performance of LILW disposal sites  

E-Print Network (OSTI)

short-lived and long-lived radionuclides) is to use disposalresult in the escape of radionuclides from the disposedand for retarding radionuclides that could potentially

Faybishenko, Boris; Witherspoon, Paul A.

2008-01-01T23:59:59.000Z

182

Criteria and techniques for field characterization and modelingrelated to selecting and evaluating performance of LILW disposalsites  

SciTech Connect

Argentina is faced with the challenging problem ofdeveloping technology for near-surface disposal and isolation of low- andintermediate-level radioactive waste (LILW). The preferred option fordisposal of LILW (including both relatively short-lived and long-livedradionuclides) is to use disposal facilities that arenear-surface--either above or below ground level [IAEA, 1985; 2001a;2004]. How individual components of a waste disposal system perform(including waste forms, waste containers, engineered barriers and hostenvironment) will determine system safety and the safety of thesurrounding environment [IAEA, 1999]. The lack of appropriate engineeringfor the backfill, and for the selection of sealing and covering materialsfor trenches, vaults, and ditches, could result in the escape ofradionuclides from the disposed wastes [IAEA, 1994a; 2001b]. Therefore,assessment and design of backfill, barriers, and cover materials are veryimportant, both for preventing invasion of water into the disposalsystem, and for retarding radionuclides that could potentially migratefrom the system into the atmosphere or groundwater [IAEA, 1982; 1994b;2001a].

Faybishenko, Boris; Witherspoon, Paul A.

2007-01-12T23:59:59.000Z

183

Axial Tomography from Digitized Real Time Radiography  

DOE R&D Accomplishments (OSTI)

Axial tomography from digitized real time radiographs provides a useful tool for industrial radiography and tomography. The components of this system are: x-ray source, image intensifier, video camera, video line extractor and digitizer, data storage and reconstruction computers. With this system it is possible to view a two dimensional x-ray image in real time at each angle of rotation and select the tomography plane of interest by choosing which video line to digitize. The digitization of a video line requires less than a second making data acquisition relatively short. Further improvements on this system are planned and initial results are reported.

Zolnay, A. S.; McDonald, W. M.; Doupont, P. A.; McKinney, R. L.; Lee, M. M.

1985-01-18T23:59:59.000Z

184

Axial tomography from digitized real time radiography  

SciTech Connect

Axial tomography from digitized real time radiographs provides a useful tool for industrial radiography and tomography. The components of this system are: x-ray source, image intensifier, video camera, video line extractor and digitizer, data storage and reconstruction computers. With this system it is possible to view a two dimensional x-ray image in real time at each angle of rotation and select the tomography plane of interest by choosing which video line to digitize. The digitization of a video line requires less than a second making data acquisition relatively short. Further improvements on this system are planned and initial results are reported.

Zolnay, A.S.; McDonald, W.M.; Doupont, P.A.; McKinney, R.L.; Lee, M.M.

1985-01-18T23:59:59.000Z

185

Environment Induced Time Arrow  

E-Print Network (OSTI)

The spread of the time arrows from the environment to an observed subsystem is followed within a harmonic model. A similarity is pointed out between irreversibility and a phase with spontaneously broken symmetry. The causal structure of interaction might be lost in the irreversible case, as well. The Closed Time Path formalism is developed for classical systems and shown to handle the time arrow problem in a clear and flexible manner. The quantum case is considered, as well, and the common origin of irreversibility and decoherence is pointed out.

Janos Polonyi

2012-06-25T23:59:59.000Z

186

VARIABLE TIME DELAY MEANS  

DOE Patents (OSTI)

An electrically variable time delay line is described which may be readily controlled simuitaneously with variable impedance matching means coupied thereto such that reflections are prevented. Broadly, the delay line includes a signal winding about a magnetic core whose permeability is electrically variable. Inasmuch as the inductance of the line varies directly with the permeability, the time delay and characteristic impedance of the line both vary as the square root of the permeability. Consequently, impedance matching means may be varied similariy and simultaneously w:th the electrically variable permeability to match the line impedance over the entire range of time delay whereby reflections are prevented.

Clemensen, R.E.

1959-11-01T23:59:59.000Z

187

Time, energy & form  

E-Print Network (OSTI)

Physical manifestations of time occur in natural forms of all sizes. Architectural form serves as shelter while providing a built envelope of human life, simultaneously influencing and influenced by energetic activities ...

McInnis, Martha Jane

1982-01-01T23:59:59.000Z

188

Dogs and Time  

NLE Websites -- All DOE Office Websites (Extended Search)

Question: I travel often and worry how leaving for long periods of time (and boarding my dog) will affect her. I wouldn't think that dogs could understand the concept of...

189

Wood Use Across Time  

E-Print Network (OSTI)

?Forest products history and use ?Forest resource- the big picture ?Consumption- the big picture ?Trends forest products industry ? pulp & paper ? solid woodBack in Time ?1492 ? Columbus sailed the ocean blue! ? wood use- fuelwood American Indians ?1634: Jean Nicolet

Scott Bowe; United States Wood Use

2005-01-01T23:59:59.000Z

190

Technical Talks Timing  

NLE Websites -- All DOE Office Websites (Extended Search)

Talks Timing The technical talks should last a maximum of 15 minutes with 5 minutes for set-up and 5 minutes for Q&A. No teamgroup presentations are allowed. The objective of...

191

Solid-State Lighting: DOE Selections  

NLE Websites -- All DOE Office Websites (Extended Search)

Financial Financial Opportunities Printable Version Share this resource Send a link to Solid-State Lighting: DOE Selections to someone by E-mail Share Solid-State Lighting: DOE Selections on Facebook Tweet about Solid-State Lighting: DOE Selections on Twitter Bookmark Solid-State Lighting: DOE Selections on Google Bookmark Solid-State Lighting: DOE Selections on Delicious Rank Solid-State Lighting: DOE Selections on Digg Find More places to share Solid-State Lighting: DOE Selections on AddThis.com... Current Opportunities DOE Selections Related Opportunities DOE Selections The U.S. Department of Energy awards research grants targeting advances in solid-state lighting. The following links provide information on the recipients of these grants and summaries of the research projects they are

192

Maps of Selected State Subdivisions  

U.S. Energy Information Administration (EIA) Indexed Site

Crude Oil, Natural Gas, and Natural Gas Liquids Crude Oil, Natural Gas, and Natural Gas Liquids Proved Reserves Summary Maps of Selected State Subdivisions Map 1: Alaska Map 2: California Map 3: Louisiana Map 4: New Mexico Map 5: Texas Map 6: Western Planning Area, Gulf of Mexico Map 7: Central Planning Area, Gulf of Mexico Map 8: Eastern Planning Area, Gulf of Mexico Map 1: Alaska AK 50 - North Onshore and Offshore AK 10 - South Onshore AK 05 - South State Offshore AK 00 - South Federal Offshore Map 2: California CA 50 - Coastal Region Onshore CA 90 - Los Angeles Basin Onshore CA 10 - San Joaquin Basin Onshore

193

Guidelines for Selecting Cool Roofs  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

BUILDING TECHNOLOGIES PROGRAM BUILDING TECHNOLOGIES PROGRAM Guidelines for Selecting Cool Roofs July 2010 V. 1.2 Prepared by the Fraunhofer Center for Sustainable Energy Systems for the U.S. Department of Energy Building Technologies Program and Oak Ridge National Laboratory under contract DE-AC05-00OR22725. Additional technical support provided by Lawrence Berkeley National Laboratory and the Federal Energy Management Program. Authors: Bryan Urban and Kurt Roth, Ph.D. ii Table of Contents Introduction ..................................................................................................................................... 3 Why Use Cool Roofs .............................................................................................................. 3

194

Valve selection handbook. Third edition  

Science Conference Proceedings (OSTI)

This book covers the fundamentals of value construction and application, and analyzes the different hazards and requirements of all types of industrial fluid flow situations. This book expands the coverage of pressure relief valves and rupture discs. It includes a new section on damping valve chatter, which is a serious problem in installations such as atomic power plants where valve chatter could have catastrophic consequences to the safety of the plant. There is also new information on performance of spring-loaded pressure relief valves and a closer examination of valve selection with respect to rupture discs and explosion venting.

Zappe, R.W. (ICI Australia Operations Pty. Ltd. (AU))

1991-01-01T23:59:59.000Z

195

Adaptive time-frequency analysis based on autoregressive modeling  

Science Conference Proceedings (OSTI)

A new adaptive method for discrete time-frequency analysis based on autoregressive (AR) modeling is introduced. The performance of AR modeling often depends upon a good selection of the model order. The predictive least squares (PLS) principle of Rissanen ... Keywords: Adaptive filters, Autoregressive modeling, Least squares methods, Model order, Time-frequency analysis

Antonio H. Costa; Stephan Hengstler

2011-04-01T23:59:59.000Z

196

Matching customer requests to service offerings in real-time  

Science Conference Proceedings (OSTI)

Classic request-response Service-oriented architecture (SOA) has reached a level of maturity where SOA inspired extensions are enabling new and creative domains like the Internet of Things, real-time business or real-time Web. These new domains impose ... Keywords: SOA, complex event processing, mediation, nonfunctional properties, service selection

Marcel Tilly; Stephan Reiff-Marganiec

2011-03-01T23:59:59.000Z

197

High temperature size selective membranes  

DOE Green Energy (OSTI)

The objective of this research is to develop a high temperature size selective membrane capable of separating gas mixture components from each other based on molecular size, using a molecular sieving mechanism. The authors are evaluating two concepts: a composite of a carbon molecular sieve (CMS) with a tightly defined pore size distribution between 3 and 4 {angstrom}, and a microporous supporting matrix which provides mechanical strength and resistance to thermal degradation, and a sandwich of a CMS film between the porous supports. The high temperature membranes the authors are developing can be used to replace the current low-temperature unit operations for separating gaseous mixtures, especially hydrogen, from the products of the water gas shift reaction at high temperatures. Membranes that have a high selectivity and have both thermal and chemical stability would improve substantially the economics of the coal gasification process. These membranes can also improve other industrial processes such as the ammonia production and oil reform processes where hydrogen separation is crucial. Results of tests on a supported membrane and an unsupported carbon film are presented.

Yates, S.F.; Zhou, S.J.; Anderson, D.J.; Til, A.E. van

1994-10-01T23:59:59.000Z

198

DOE Selects Contractor for Depleted Hexafluoride Conversion Project Support  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE Selects Contractor for Depleted Hexafluoride Conversion Project DOE Selects Contractor for Depleted Hexafluoride Conversion Project Support DOE Selects Contractor for Depleted Hexafluoride Conversion Project Support March 25, 2013 - 12:00pm Addthis Media Contact Bill Taylor, 803-952-8564 Bill.Taylor@srs.gov Cincinnati - The U.S. Department of Energy (DOE) today awarded a competitive small business task order to Navarro Research and Engineering Inc. of Oak Ridge, Tennessee. The award is a $22 million, time and materials task order with a three-year performance period and two one-year extension options. Navarro Research and Engineering Inc. will provide engineering and operations technical support services to the DOE Portsmouth Paducah Project Office (PPPO) in Lexington, Kentucky and the Depleted Uranium Hexafluoride (DUF6) Conversion Project in Paducah, Kentucky and Portsmouth, Ohio.

199

Content selection from semantic web data  

Science Conference Proceedings (OSTI)

So far, there has been little success in Natural Language Generation in coming up with general models of the content selection process. Nonetheless, there has been some work on content selection that employ Machine learning or heuristic search. On the ...

Nadjet Bouayad-Agha; Gerard Casamayor; Leo Wanner; Chris Mellish

2012-05-01T23:59:59.000Z

200

NSIT Computer Time Services: Internet Time Service (ITS) ...  

Science Conference Proceedings (OSTI)

Page 1. NIST Special Publication 250-59 NIST Computer Time Services: Internet Time Service (ITS), Automated Computer Time Service (ACTS), ...

2012-09-16T23:59:59.000Z

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

SelectUSA 2013 Investment Summit  

Science Conference Proceedings (OSTI)

... Gaithersburg, MD 20899-4800. susa-summit-vertical. SelectUSA 2013 Investment Summit. October 31- November 1, 2013 ...

2013-08-16T23:59:59.000Z

202

Select an Energy-Efficient Centrifugal Pump  

SciTech Connect

BestPractices Program tip sheet discussing pumping system efficiency by selecting an energy-efficient centrifugal pump.

2005-10-01T23:59:59.000Z

203

Origin of Mutations Under Selection: The Adaptive  

E-Print Network (OSTI)

Origin of Mutations Under Selection: The Adaptive Mutation Controversy John R. Roth,1 Elisabeth 2006 by Annual Reviews. All rights reserved 0066-4227/06/1013-0477$20.00 Key Words natural selection Growth under selection causes new genotypes to predominate in a population. It is difficult to determine

California at Davis, University of

204

Brief Contributions________________________________________________________________________________ Optimal Selective Huffman Coding  

E-Print Network (OSTI)

________________________________________________________________________________ Optimal Selective Huffman Coding for Test-Data Compression Xrysovalantis Kavousianos, Member, IEEE, Emmanouil Kalligeros, Member, IEEE, and Dimitris Nikolos, Member, IEEE Abstract--Selective Huffman coding are also verified experimentally. Index Terms--Embedded testing techniques, IP cores, selective Huffman

Kavousianos, Xrysovalantis

205

Ambiguity in portfolio selection Georg Pflug  

E-Print Network (OSTI)

Ambiguity in portfolio selection Georg Pflug David Wozabal Abstract In this paper, we consider- cess, not just a single optimization task. It comprises of the selection of a statistical model the ambiguity in choosing the probability model and therefore is robust in following sense: The selected

Pflug, Georg

206

SELECTED BIBLIOGRAPHY ON APPLICATIONS OF ELECTRICTY  

E-Print Network (OSTI)

SELECTED BIBLIOGRAPHY ON APPLICATIONS OF ELECTRICTY IN FISHERY SCIENCE Marine Biological Laboratory, Director SELECTED BIBLIOGRAPHY ON THE APPLICATIONS OF ELECTRICITY IN FISHERY SCIENCE by Vernon C. Applegate Acknowledgments 55 #12;SELECTED BIBLIOGRAPHY ON THE APPLICATIONS OF ELECTRICITY IN FISHERY SCIENCE Applications

207

Studies on selection of controlled variables  

E-Print Network (OSTI)

Studies on selection of controlled variables by Vidar Alstad A Thesis Submitted for the Degree. Thus, the selection of controlled variables integrates the optimization and the control layer. Selecting the right controlled variables can be of paramount importance. Many chem­ ical processes

Skogestad, Sigurd

208

Studies on selection of controlled variables  

E-Print Network (OSTI)

Studies on selection of controlled variables by Vidar Alstad A Thesis Submitted for the Degree. Thus, the selection of controlled variables integrates the optimization and the control layer. Selecting the right controlled variables can be of paramount importance. Many chem- ical processes

Skogestad, Sigurd

209

Model selection for Gaussian regression with  

E-Print Network (OSTI)

Model selection for Gaussian regression with random design Lucien Birg´e Universit´e Paris VI and U of the L2-distance allows to recover the usual rates and to perform model selection in great generality 62G07. Key words and phrases. Random design regression, model selection, Hellinger distance, minimax

Université Pierre-et-Marie-Curie, Paris 6

210

Optimal Adaptive Waveform Selection for Target Tracking  

E-Print Network (OSTI)

Optimal Adaptive Waveform Selection for Target Tracking Barbara La Scala Mohammad Rezaeian Bill algorithms. This paper describes an optimal adaptive waveform selection algorithm for target tracking. An adap- tive scheduling algorithm that selects the waveforms to be used in future epochs based on current

Rezaeian, Mohammad-Jafar

211

Adaptive sampling for Bayesian variable selection  

E-Print Network (OSTI)

Adaptive sampling for Bayesian variable selection DAVID J. NOTT Department of Statistics for variable selection and for dealing with model un- certainty have become increasingly popular in recent consider adaptive Markov chain Monte Carlo schemes for Bayesian variable selection in Gaussian linear

Blennerhassett, Peter

212

Selective inductive powering system for paper computing  

Science Conference Proceedings (OSTI)

We present a method of selective wireless power transferring for paper computing. The novelty of this method lies in the power transmitter can be controlled to selectively activate different receivers in the context of wireless power transferring with ... Keywords: paper computing, selective wireless power

Kening Zhu; Hideaki Nii; Owen Noel Newton Fernando; Adrian David Cheok

2011-11-01T23:59:59.000Z

213

MIS-based sensors with hydrogen selectivity  

DOE Patents (OSTI)

The invention provides hydrogen selective metal-insulator-semiconductor sensors which include a layer of hydrogen selective material. The hydrogen selective material can be polyimide layer having a thickness between 200 and 800 nm. Suitable polyimide materials include reaction products of benzophenone tetracarboxylic dianhydride 4,4-oxydianiline m-phenylene diamine and other structurally similar materials.

Li; ,Dongmei (Boulder, CO); Medlin, J. William (Boulder, CO); McDaniel, Anthony H. (Livermore, CA); Bastasz, Robert J. (Livermore, CA)

2008-03-11T23:59:59.000Z

214

Probabilistic timed behavior trees  

Science Conference Proceedings (OSTI)

The Behavior Tree notation has been developed as a method for systematically and traceably capturing user requirements. In this paper we extend the notation with probabilistic behaviour, so that reliability, performance, and other dependability properties ... Keywords: behavior trees, model checking, probabilities, timed automata

Robert Colvin; Lars Grunske; Kirsten Winter

2007-07-01T23:59:59.000Z

215

Surface Soil Changes Following Selective Logging in an Eastern Amazon Forest  

Science Conference Proceedings (OSTI)

In the Brazilian Amazon, selective logging is second only to forest conversion in its extent. Conversion to pasture or agriculture tends to reduce soil nutrients and site productivity over time unless fertilizers are added. Logging removes ...

Lydia P. Olander; Mercedes M. Bustamante; Gregory P. Asner; Everaldo Telles; Zayra Prado; Plínio B. Camargo

2005-04-01T23:59:59.000Z

216

Genepool Time Heatmaps  

NLE Websites -- All DOE Office Websites (Extended Search)

Genepool Time Heatmaps Genepool Time Heatmaps Heatmap of Time and Slots Requested vs Time Waited (in hours) | Queue: All | Last 7 Days Time Requested Slots 1wk Job Count Longest Wait 1 23.0 (233) 0.37 (1819) 27.54 (49888) 5.85 (124593) 1.23 (39835) 0.34 (732) 0 0.4 (224) 0.02 (1) 217325 538.96 2 0 0.01 (19) 2.54 (78) 0.2 (140) 0.99 (2683) 0 0 0 0 2920 9.1 4 0.08 (1) 0 2.82 (141) 0.36 (143) 1.07 (12) 0.06 (5) 0.01 (5) 0.06 (1) 1.3 (5) 313 20.48 6 0.01 (2) 0 0.09 (32) 0.07 (1) 0 0 0 0 0 35 1.22 8 0.04 (24) 4.32 (7423) 5.31 (1999) 0.53 (316) 13.14 (2486) 0.01 (2) 1.21 (88) 1.3 (34) 8.33 (68) 12440 46.16 10 0 0 0 0 0 0 0 8.56 (1) 0 1 8.56 16 0 0 0 0.03 (1) 0 0 0 0 0 1 0.03 24 0 0 0 0 0 0 0 0 0.01 (1) 1 0.01 32 0 0 0 0.04 (14) 0 0 0 0.01 (6) 0 20 0.26

217

Chameleon: adaptive selection of collections  

Science Conference Proceedings (OSTI)

Languages such as Java and C#, as well as scripting languages like Python, and Ruby, make extensive use of Collection classes. A collection implementation represents a fixed choice in the dimensions of operation time, space utilization, and synchronization. ... Keywords: bloat, collections, java, semantic profiler

Ohad Shacham; Martin Vechev; Eran Yahav

2009-06-01T23:59:59.000Z

218

Meteorology: typical meteorological data for selected stations in Ghana  

Open Energy Info (EERE)

data for selected stations in Ghana data for selected stations in Ghana from NREL Dataset Summary Description (Abstract): Each TMY is a data set of hourly values of solar radiation and meteorological elements for a 1-year period. Solar radiation is modeled using the NREL METSTAT model, with surface observed cloud cover being the principal model input. The container file contains one TMY file for each selected station in the region, plus documentation files and a TMY data reader file for use with Microsoft Excel. (Purpose): Simulations> (Supplemental Information): A TMY consists of months selected from individual years and concatenated to form a complete year. The intended use is for computer simulations of solar energy conversion systems and building systems. Because of the selection criteria, these TMYs are not appropriate for simulations of wind energy conversion systems. A TMY provides a standard for hourly data for solar radiation and other meteorological elements that permit performance comparisons of system types and configurations for one or more locations. A TMY is not necessarily a good indicator of conditions over the next year, or even the next 5 years. Rather, it represents conditions judged to be typical over a long period of time, such as 30 years. Because they represent typical rather than extreme conditions, they are not suited for designing systems and their components to meet the worst-case conditions occurring at a location.

219

A Selective Survey of the Finite-Difference Time-Domain Literature  

E-Print Network (OSTI)

the U.S. EPA eGrid database [12], and appropriate regional fuel prices as in [13], we construct a pure economic dispatch. We use average CO2 equivalent emissions data from the eGrid database.S. Environmental Protection Agency eGRID Emissions & Generation Resource Integrated Database, eGRID2006 Version 1

Schneider, John B.

220

Is it time to rethink SO{sub 2} control technology selection?  

Science Conference Proceedings (OSTI)

The article traces the history of flue gas desulfurization (FGD) systems in power plants in the USA following the 1990 Clean Air Act which divided boilers into Phase I (larger SO{sub 2} emitters) and Phase II units. The Clean Air Interstate Rule (CAIR) will soon require emission control on smaller boilers burning low and medium-sulfur coal. Today the systems of choice are dry FGD systems for low sulfur coals and greater than wet LSFO. (limestone forced oxidation systems) for coal with sulfur content about 2%. Demand for wet FGD coupled with tighter regulations has led to significant cost increases in LSFO. technology. 4 refs., 2 figs.

Dickerman, J.; Swell, M. [Chemical Lime (United States)

2007-11-15T23:59:59.000Z

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Software Selection for Reliability Optimization using Time Series Analysis and Machine Learning  

E-Print Network (OSTI)

Difference and ACF of “ACF and PACF of residuals of “4: Difference of “Data1”. The ACF (Autocorrelation Function)

Mu, Yali

2013-01-01T23:59:59.000Z

222

Study of energy conservation in selected institutions of higher education  

SciTech Connect

The purpose of this study was to determine the relationship between 1) energy usage and number of full-time-equivalent students and 2) energy usage and twenty-two selected energy savings measures incorporated by the Illinois public universities in fiscal years 1976 and 1980. The study culminated in the evaluation of the statistical significance and positive or negative relationships of the data through use of the Spearman rho correlation formula. The conclusions of this study were that there was a positive relationship between decreased 1) energy usage and numbers of full-time-equivalent students and decreased 2) energy usage and twenty-two selected energy-savings measures incorporated by the Illinois public universities in fiscal years 1976 and 1980.

Pavlisin, M.

1983-01-01T23:59:59.000Z

223

Timed fast charger  

Science Conference Proceedings (OSTI)

In a charger for rechargeable electrochemical cells, a transformer charging circuit supplies a charging current to the battery at a fast charge rate for a predetermined time followed by a continuous slow charge rate. A normally closed automatic reset thermostat in series with the rectifier diodes in the charging circuit, and thermally coupled to them, opens after a period of time, dependent upon the heat generated by the rectifier diodes and upon the thermal mass of the thermostat and diodes, and terminates the fast charge current. A resistor, shunted across the thermostat and thermally coupled to it, establishes a slow charge rate current path when the thermostat opens. Heat generated in the resistor causes the thermostat to remain open as long as the battery is connected and ac power is supplied to the transformer primary winding.

Mullersman, F.H.

1981-10-27T23:59:59.000Z

224

Internet Topology over Time  

E-Print Network (OSTI)

There are few studies that look closely at how the topology of the Internet evolves over time; most focus on snapshots taken at a particular point in time. In this paper, we investigate the evolution of the topology of the Autonomous Systems graph of the Internet, examining how eight commonly-used topological measures change from January 2002 to January 2010. We find that the distributions of most of the measures remain unchanged, except for average path length and clustering coefficient. The average path length has slowly and steadily increased since 2005 and the average clustering coefficient has steadily declined. We hypothesize that these changes are due to changes in peering policies as the Internet evolves. We also investigate a surprising feature, namely that the maximum degree has changed little, an aspect that cannot be captured without modeling link deletion. Our results suggest that evaluating models of the Internet graph by comparing steady-state generated topologies to snapshots of the real data ...

Edwards, Benjamin; Stelle, George; Forrest, Stephanie

2012-01-01T23:59:59.000Z

225

Space Time Matter inflation  

E-Print Network (OSTI)

We study a model of power-law inflationary inflation using the Space-Time-Matter (STM) theory of gravity for a five dimensional (5D) canonical metric that describes an apparent vacuum. In this approach the expansion is governed by a single scalar (neutral) quantum field. In particular, we study the case where the power of expansion of the universe is $p \\gg 1$. This kind of model is more successful than others in accounting for galaxy formation.

Mariano Anabitarte; Mauricio Bellini

2005-08-31T23:59:59.000Z

226

TIME DOMAIN MULTIPLE QUANTUM NMR  

E-Print Network (OSTI)

Comparison with Single Quantum NMR C. Frequency Selectiveli, A. Bax, "Two Dimensional NMR" , Delft University Press,G. Bodenhausen, Prog. in NMR Spec. A. Pines, D. Wemmer, J.

Weitekamp, D.P.

2008-01-01T23:59:59.000Z

227

Material selection for electrooptic deflectors  

SciTech Connect

The selection of a material for a practical device is generally guided by a number of criteria, including cost, size, difficulty of fabrication, durability, driver requirements, and system constraints. A quantitative analysis can usually be made for comparison, or a figure of merit can be computed. In the case of materials for electrooptical (EO) devices the choice is often made based on the availability of materials meeting some minimum system requirement. For fast EO deflectors, where a large number of resolvable spots is required, the choice of materials is quite limited. A model of just such a device is proposed; it is based on the resolution of 400 spots and reasonable boundary conditions. The model predicts that to be successful, an EO material must be chosen that has a linear EO coefficient (r/sub 33/) of at least 336 pm/V. A survey was conducted of the EO materials which are generally available. Based on the model and the survey, Czochralski crystal growth of strontium barium niobate (SBN:60) is recommended. Although SBN:60 does not have the largest EO coefficient, it may be the easiest to grow in the required size and optical quality, thus satisfying the availability criterion. It should be borne in mind that many materials may be grown by this technique and there are many new and potential applications for EO materials. 92 refs., 18 figs., 14 tabs.

Not Available

1988-09-01T23:59:59.000Z

228

Enhancing evolutionary instance selection algorithms by means of fuzzy rough set based feature selection  

Science Conference Proceedings (OSTI)

In recent years, fuzzy rough set theory has emerged as a suitable tool for performing feature selection. Fuzzy rough feature selection enables us to analyze the discernibility of the attributes, highlighting the most attractive features in the construction ... Keywords: Evolutionary algorithms, Feature selection, Instance selection, Nearest neighbor, Rough sets

Joaquín Derrac; Chris Cornelis; Salvador García; Francisco Herrera

2012-03-01T23:59:59.000Z

229

QUADRENNIAL MCNP TIMING STUDY  

Science Conference Proceedings (OSTI)

The Los Alamos National Laboratory Monte Carlo N-Particle radiation transport code, MCNP, is widely used around the world for many radiation protection and shielding applications. As a well-known standard it is also an excellent vehicle for assessing the relative performance of scientific computing platforms. Every three-to-four years a new version of MCNP is released internationally by the Radiation Safety Information Computational Center (RSICC) in Oak Ridge, Tennessee. For each of the past few releases, we have also done a timing study to assess the progress of scientific computing platforms and software. These quadrennial timing studies are valuable to the radiation protection and shielding community because (a) they are performed by a recognized scientific team, not a computer vendor, (b) they use an internationally recognized code for radiation protection and shielding calculations, (c) they are eminently reproducible since the code and the test problems are internationally distributed. Further, if one has a computer platform, operating system, or compiler not presented in our results, its performance is directly comparable to the ones we report because it can use the same code, data, and test problems as we used. Our results, using a single processor per platform, indicate that hardware advances during the past three years have improved performance by less than a factor of two and software improvements have had a marginal effect on performance. The most significant impacts on performance have resulted from developments in multiprocessing and multitasking. The other most significant advance in the last three years has been the accelerated improvements in personal computers. In the last timing study, the tested personal computer was approximately a factor of four slower that the fastest machine tested, a DEC Alphastation 500. In the present study, the fastest PC tested was less than a factor of two slower than the fastest platform, which is a Compaq (previously DEC) Alpha XP1000.

E. C. SELCOW; B. D. LANSRUD

2000-09-01T23:59:59.000Z

230

Exploiting VERITAS Timing Information  

E-Print Network (OSTI)

The 499 pixel photomultiplier cameras of the VERITAS gamma ray telescopes are instrumented with 500MHz sampling Flash ADCs. This paper describes a preliminary investigation of the best methods by which to exploit this information so as to optimize the signal-to-noise ratio for the detection of Cherenkov light pulses. The FADCs also provide unprecedented resolution for the study of the timing characteristics of Cherenkov images of cosmic-ray and gamma-ray air showers. This capability is discussed, together with the implications for gamma-hadron separation.

J. Holder; for the VERITAS Collaboration

2005-07-19T23:59:59.000Z

231

Heat Recovery Steam Generator Materials Selection Guideline  

Science Conference Proceedings (OSTI)

A considerable number of failures have occurred over the past decade in heat recovery steam generators (HRSGs). Many of these failures are attributed to poor design, improper operation, poor fabrication, or poor installation practices, but a number of them are attributed directly to improper material selection. In March 2004, the Electric Power Research Institute (EPRI) published the first heat recovery steam generator materials selection and repair guidelines (HRSG Material Selection and Repair Guidelin...

2010-12-19T23:59:59.000Z

232

Physical Properties Data Center Selected Data...  

NLE Websites -- All DOE Office Websites (Extended Search)

Physical Properties Data Center Selected Data Sets and Data Collections Complete data set listings available through each individual data center. For more information about NASA's...

233

SELECTIVE ABSORBER COATED FOILS FOR SOLAR COLLECTORS  

E-Print Network (OSTI)

of the University of California, nor any of their employees,of the University of California. The views and opinions ofof the University of California. SELECTIVE ABSORBER COATED

Lampert, Carl M.

2013-01-01T23:59:59.000Z

234

Automated fenestration selection based on lighting performance...  

NLE Websites -- All DOE Office Websites (Extended Search)

i.e., aims at automated selection of fenestration systems that best meet specific lighting performance goals. The new method is based on manipulation of matrices that represent...

235

Available Technologies: High Selectivity Peptides for Cancer ...  

Biofuels; Biotechnology & Medicine. Diagnostics and Therapeutics; Medical Devices; ... Rac1b: A Highly Selective Marker and Target for Cancer, IB-2167 ;

236

Produced by Selective Electron Beam Melting  

Science Conference Proceedings (OSTI)

The development of processing TiAl by additive manufacturing by using the selective electron beam melting (SEBM) provides a new approach to reach near

237

The Velocity-Selecting Cerenkov Counter  

E-Print Network (OSTI)

BAFFLE VELOCITY - SELECTING CERENKOV COUNTER (C 2) FiJI. 1velocity-selectinp: Cerenkov counter. ueaL-31;S CYLINDRICA~

Chamberlain, Owen; Weigand, Clyde

1956-01-01T23:59:59.000Z

238

Information Resources: Successful Selection of LED Streetlight...  

NLE Websites -- All DOE Office Websites (Extended Search)

Successful Selection of LED Streetlight Luminaires: Optimizing Illumination and Economic Performance This March 6, 2013 webcast reviewed the factors involved in successful...

239

Selective Ion Source for Semiconductor Devices  

Berkeley National Laboratory's new selective ion source produces a beam of boron, arsenic or phosphorus ions from plasma that is essentially free of ...

240

Solar Selective Absorption Coatings - Energy Innovation Portal  

Sandia has developed a new class of solar selective absorber coatings that significantly improve the thermal conversion efficiency of solar units by reducing ...

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Solar selective absorption coatings - Energy Innovation Portal  

A new class of solar selective absorption coatings are disclosed. These coatings comprise a structured metallic overlayer such that the overlayer has a sub-micron ...

242

Geothermal: Sponsored by OSTI -- Selected bibliography: cost...  

Office of Scientific and Technical Information (OSTI)

Selected bibliography: cost and energy savings of conservation and renewable energy technologies Geothermal Technologies Legacy Collection HelpFAQ | Site Map | Contact Us | Admin...

243

Good Timing: NIST/CU Collaboration Adds Timing Capability ...  

Science Conference Proceedings (OSTI)

... With the added capability to track the timing of dynamic biochemical reactions, cell ... to measure sensor signals at two points in time at a rate of up to ...

2012-02-07T23:59:59.000Z

244

A Time Bucket Formulation for the TSP with Time Windows  

E-Print Network (OSTI)

Nov 10, 2009 ... The Traveling Salesman Problem with Time Windows (TSPTW) is the problem of finding a ... To obtain a good partition of the time windows, we.

245

NEUP Project Selections_September212011_IRP and Infrastructure...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

NEUP Project SelectionsSeptember212011IRP and Infrastructure Improvements NEUP Project SelectionsSeptember212011IRP and Infrastructure Improvements Projects selections for NEUP...

246

Local Energy Assurance Planning: Map of Selected Cities | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Selected Cities Local Energy Assurance Planning: Map of Selected Cities Map of the United States showing the location and population size of cities selected for Local Energy...

247

Rapid emission angle selection for rotating-shield brachytherapy  

SciTech Connect

Purpose: The authors present a rapid emission angle selection (REAS) method that enables the efficient selection of the azimuthal shield angle for rotating shield brachytherapy (RSBT). The REAS method produces a Pareto curve from which a potential RSBT user can select a treatment plan that balances the tradeoff between delivery time and tumor dose conformity. Methods: Two cervical cancer patients were considered as test cases for the REAS method. The RSBT source considered was a Xoft Axxent{sup TM} electronic brachytherapy source, partially shielded with 0.5 mm of tungsten, which traveled inside a tandem intrauterine applicator. Three anchor RSBT plans were generated for each case using dose-volume optimization, with azimuthal shield emission angles of 90 Degree-Sign , 180 Degree-Sign , and 270 Degree-Sign . The REAS method converts the anchor plans to treatment plans for all possible emission angles by combining neighboring beamlets to form beamlets for larger emission angles. Treatment plans based on exhaustive dose-volume optimization (ERVO) and exhaustive surface optimization (ERSO) were also generated for both cases. Uniform dwell-time scaling was applied to all plans such that that high-risk clinical target volume D{sub 90} was maximized without violating the D{sub 2cc} tolerances of the rectum, bladder, and sigmoid colon. Results: By choosing three azimuthal emission angles out of 32 potential angles, the REAS method performs about 10 times faster than the ERVO method. By setting D{sub 90} to 85-100 Gy{sub 10}, the delivery times used by REAS generated plans are 21.0% and 19.5% less than exhaustive surface optimized plans used by the two clinical cases. By setting the delivery time budget to 5-25 and 10-30 min/fx, respectively, for two the cases, the D{sub 90} contributions for REAS are improved by 5.8% and 5.1% compared to the ERSO plans. The ranges used in this comparison were selected in order to keep both D{sub 90} and the delivery time within acceptable limits. Conclusions: The REAS method enables efficient RSBT treatment planning and delivery and provides treatment plans with comparable quality to those generated by exhaustive replanning with dose-volume optimization.

Liu, Yunlong [Department of Electrical and Computer Engineering, University of Iowa, 4016 Seamans Center, Iowa City, Iowa 52242 (United States); Flynn, Ryan T.; Kim, Yusung; Bhatia, Sudershan K.; Sun, Wenqing [Department of Radiation Oncology, University of Iowa, 200 Hawkins Drive, Iowa City, Iowa 52242 (United States); Yang Wenjun [Department of Biomedical Engineering, University of Iowa, 1402 Seamans Center for the Engineering Arts and Sciences, Iowa City, Iowa 52242 (United States); Wu Xiaodong [Department of Electrical and Computer Engineering, University of Iowa, 4016 Seamans Center, Iowa City, Iowa 52242 and Department of Radiation Oncology, University of Iowa, 200 Hawkins Drive, Iowa City, Iowa 52242 (United States)

2013-05-15T23:59:59.000Z

248

The Heliosphere in Time  

E-Print Network (OSTI)

Because of the dynamic nature of the interstellar medium, the Sun should have encountered a variety of different interstellar environments in its lifetime. As the solar wind interacts with the surrounding interstellar medium to form a heliosphere, different heliosphere shapes, sizes, and particle contents result from the different environments. Some of the large possible interstellar parameter space (density, velocity, temperature) is explored here with the help of global heliosphere models, and the features in the resulting heliospheres are compared and discussed. The heliospheric size, expressed as distance of the nose of the heliopause to the Sun, is set by the solar wind - interstellar pressure balance, even for extreme cases. Other heliospheric boundary locations and neutral particle results correlate with the interstellar parameters as well. If the H0 clouds identified in the Millennium Arecibo survey are typical of clouds encountered by the Sun, then the Sun spends ~99.4% of the time in warm low density ISM, where the typical upwind heliosphere radii are up to two orders of magnitude larger than at present.

H. -R. Müller; P. C. Frisch; B. D. Fields; G. P. Zank

2008-10-02T23:59:59.000Z

249

Graduate Health Insurance Selection/Reporting Information and Directions Please read this information carefully  

E-Print Network (OSTI)

in Massachusetts. It is your responsibility to carefully evaluate your insurance plan for adequacy before reportingGraduate Health Insurance Selection/Reporting Information and Directions Please read Insurance Plan (QSHIP) or to report your comparable health insurance coverage. All full time and ¾ time

Snider, Barry B.

250

Symbolic Test Selection Based on Approximate Analysis  

E-Print Network (OSTI)

Symbolic Test Selection Based on Approximate Analysis Bertrand Jeannet, Thierry J´eron, Vlad Rusu}@irisa.fr Abstract. This paper addresses the problem of generating symbolic test cases for testing the conformance. The challenge we consider is the selection of test cases according to a test purpose, which is here a set

Paris-Sud XI, Université de

251

Negative selection algorithms without generating detectors  

Science Conference Proceedings (OSTI)

Negative selection algorithms are immune-inspired classifiers that are trained on negative examples only. Classification is performed by generating detectors that match none of the negative examples, and these detectors are then matched against ... Keywords: artificial immune systems, consistent learning, negative selection

Maciej Li?kiewicz; Johannes Textor

2010-07-01T23:59:59.000Z

252

Space-Conditioning System Selection Guide  

Science Conference Proceedings (OSTI)

This handbook represents a single-source guide to the selection of space-conditioning equipment for commercial facilities. Written for the utility marketing representative, it provides information on these topics: heating, cooling, ventilation, and dehumidification requirements of commercial buildings; customer needs when selecting a space-conditioning system; and, the options among energy-efficient electric space-conditioning systems for commercial buildings.

1994-01-22T23:59:59.000Z

253

Cloud service selection based on variability modeling  

Science Conference Proceedings (OSTI)

The selection among Cloud services is a recent problem in research and practice. The diversity of decision-relevant criteria, configurability of Cloud services and the need to involve human decision-makers require holistic support through models, methodologies ... Keywords: cloud service selection, decision-making, feature modeling, variability modeling

Erik Wittern; Jörn Kuhlenkamp; Michael Menzel

2012-11-01T23:59:59.000Z

254

Liquid Biofuels Strategies and Policies in selected  

E-Print Network (OSTI)

June 2011 Liquid Biofuels Strategies and Policies in selected African Countries A review of some of the challenges, activities and policy options for liquid biofuels Prepared for PISCES by Practical Action Biofuels Strategies and Policies in selected African Countries Although this research is funded by DFID

255

Selective purge for hydrogenation reactor recycle loop  

SciTech Connect

Processes and apparatus for providing improved contaminant removal and hydrogen recovery in hydrogenation reactors, particularly in refineries and petrochemical plants. The improved contaminant removal is achieved by selective purging, by passing gases in the hydrogenation reactor recycle loop or purge stream across membranes selective in favor of the contaminant over hydrogen.

Baker, Richard W. (Palo Alto, CA); Lokhandwala, Kaaeid A. (Union City, CA)

2001-01-01T23:59:59.000Z

256

On selecting Gabor features for biometric authentication  

Science Conference Proceedings (OSTI)

We describe a Gabor feature selection technique that allows us to develop a fast and robust Gabor-feature based biometric system. Existing Gabor based methods use a huge number of Gabor features to represent the patterns. Our experiments on different ... Keywords: Gabor features, automated identification, biometrics, ear authentication, equal error rate, feature selection, finger authentication

Loris Nanni; Alessandra Lumini

2009-04-01T23:59:59.000Z

257

Project Selection by Constrained Fuzzy AHP  

Science Conference Proceedings (OSTI)

The selection of a project among a set of possible alternatives is a difficult task decision makers have to face. Difficulties in selecting a project arise because of the different goals involved and because of the large number of attributes to consider. ... Keywords: AHP, decision analysis, fuzzy sets

Mario Enea; Tommaso Piazza

2004-03-01T23:59:59.000Z

258

Scale selection for supervised image segmentation  

Science Conference Proceedings (OSTI)

Finding the right scales for feature extraction is crucial for supervised image segmentation based on pixel classification. There are many scale selection methods in the literature; among them the one proposed by Lindeberg is widely used for image structures ... Keywords: Image segmentation, Max rule, Scale selection, Scale space theory, Supervised learning

Yan Li; David M. J. Tax; Marco Loog

2012-12-01T23:59:59.000Z

259

NIST Time Scale Data Archive  

Science Conference Proceedings (OSTI)

NIST Time Scale Data Archive. ... The AT1 scale is run in real time using data from an ensemble of cesium standards and hydrogen masers. ...

2013-08-07T23:59:59.000Z

260

Time and Frequency Division Homepage  

Science Conference Proceedings (OSTI)

... Controlled ClocksTelephone TimeDivision HistoryFrequently Asked Questions (FAQ)Time and Frequency from A to Z: An illustrated glossaryA Walk ...

2013-12-27T23:59:59.000Z

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Time dependent Directional Profit Model for Financial Time Series Forecasting  

E-Print Network (OSTI)

Time dependent Directional Profit Model for Financial Time Series Forecasting Jingtao YAO Chew Lim@comp.nus.edu.sg Abstract Goodness­of­fit is the most popular criterion for neural network time series forecasting. In the context of financial time series forecasting, we are not only concerned at how good the forecasts fit

Yao, JingTao

262

CCPI Round 2 Selections | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CCPI Round 2 Selections CCPI Round 2 Selections CCPI Round 2 Selections In October 2004, the U.S. Department of Energy announced its second round of project selections in the Clean Coal Power Initiative (CCPI). CCPI is a $2 billion, 10-year program to develop and demonstrate a new generation of power plant technologies. These power plants will be fueled by coal, the nation's most used fuel for electric power generation, but will achieve substantially reduced emissions of sulfur, nitrogen and mercury compounds. Some of the projects also will significantly lessen the release of carbon dioxide, a greenhouse gas. The following projects were selected from 13 proposals in the 2nd round of competition for joint government-industry financing: Location of Peabody Mustang Clean Coal Project Peabody Mustang Clean Coal

263

Variable selection in nonparametric additive models  

E-Print Network (OSTI)

We consider a nonparametric additive model of a conditional mean function in which the number of variables and additive components may be larger than the sample size but the number of nonzero additive components is "small" relative to the sample size. The statistical problem is to determine which additive components are nonzero. The additive components are approximated by truncated series expansions with B-spline bases. With this approximation, the problem of component selection becomes that of selecting the groups of coefficients in the expansion. We apply the adaptive group Lasso to select nonzero components, using the group Lasso to obtain an initial estimator and reduce the dimension of the problem. We give conditions under which the group Lasso selects a model whose number of components is comparable with the underlying model, and the adaptive group Lasso selects the nonzero components correctly with probability approaching one as the sample size increases and achieves the optimal rate of convergence. Th...

Huang, Jian; Wei, Fengrong; 10.1214/09-AOS781

2010-01-01T23:59:59.000Z

264

Biofuel Feedstock Assessment For Selected Countries  

SciTech Connect

Findings from biofuel feedstock production assessments and projections of future supply are presented and discussed. The report aims to improve capabilities to assess the degree to which imported biofuel could contribute to meeting future U.S. targets to reduce dependence on imported oil. The study scope was focused to meet time and resource requirements. A screening process identified Argentina, Brazil, Canada, China, Colombia, India, Mexico, and the Caribbean Basin Initiative (CBI) region for initial analysis, given their likely role in future feedstock supply relevant to U.S. markets. Supply curves for selected feedstocks in these countries are projected for 2012, 2017 and 2027. The supply functions, along with calculations to reflect estimated supplies available for export and/or biofuel production, were provided to DOE for use in a broader energy market allocation study. Potential cellulosic supplies from crop and forestry residues and perennials were also estimated for 2017 and 2027. The analysis identified capacity to potentially double or triple feedstock production by 2017 in some cases. A majority of supply growth is derived from increasing the area cultivated (especially sugarcane in Brazil). This is supplemented by improving yields and farming practices. Most future supplies of corn and wheat are projected to be allocated to food and feed. Larger shares of future supplies of sugarcane, soybean and palm oil production will be available for export or biofuel. National policies are catalyzing investments in biofuel industries to meet targets for fuel blending that generally fall in the 5-10% range. Social and environmental concerns associated with rapid expansion of feedstock production are considered. If the 2017 projected feedstock supply calculated as 'available' for export or biofuel were converted to fuel, it would represent the equivalent of about 38 billion gallons of gasoline. Sugarcane and bagasse dominate the available supply, representing 64% of the total. Among the nations studied, Brazil is the source of about two-thirds of available supplies, followed distantly by Argentina (12%), India and the CBI region.

Kline, Keith L [ORNL; Oladosu, Gbadebo A [ORNL; Wolfe, Amy K [ORNL; Perlack, Robert D [ORNL; Dale, Virginia H [ORNL

2008-02-01T23:59:59.000Z

265

Biofuel Feedstock Assessment for Selected Countries  

DOE Green Energy (OSTI)

Findings from biofuel feedstock production assessments and projections of future supply are presented and discussed. The report aims to improve capabilities to assess the degree to which imported biofuel could contribute to meeting future U.S. targets to reduce dependence on imported oil. The study scope was focused to meet time and resource requirements. A screening process identified Argentina, Brazil, Canada, China, Colombia, India, Mexico, and the Caribbean Basin Initiative (CBI) region for initial analysis, given their likely role in future feedstock supply relevant to U.S. markets. Supply curves for selected feedstocks in these countries are projected for 2012, 2017 and 2027. The supply functions, along with calculations to reflect estimated supplies available for export and/or biofuel production, were provided to DOE for use in a broader energy market allocation study. Potential cellulosic supplies from crop and forestry residues and perennials were also estimated for 2017 and 2027. The analysis identified capacity to potentially double or triple feedstock production by 2017 in some cases. A majority of supply growth is derived from increasing the area cultivated (especially sugarcane in Brazil). This is supplemented by improving yields and farming practices. Most future supplies of corn and wheat are projected to be allocated to food and feed. Larger shares of future supplies of sugarcane, soybean and palm oil production will be available for export or biofuel. National policies are catalyzing investments in biofuel industries to meet targets for fuel blending that generally fall in the 5-10% range. Social and environmental concerns associated with rapid expansion of feedstock production are considered. If the 2017 projected feedstock supply calculated as ‘available’ for export or biofuel were converted to fuel, it would represent the equivalent of about 38 billion gallons of gasoline. Sugarcane and bagasse dominate the available supply, representing 64% of the total. Among the nations studied, Brazil is the source of about two-thirds of available supplies, followed distantly by Argentina (12%), India and the CBI region.

Kline, K.L.; Oladosu, G.A.; Wolfe, A.K.; Perlack, R.D.; Dale, V.H.

2008-02-18T23:59:59.000Z

266

NETL: News Release - Projects Selected to Advance Innovative Materials for  

NLE Websites -- All DOE Office Websites (Extended Search)

14, 2010 14, 2010 Projects Selected to Advance Innovative Materials for Fossil Energy Power Systems Washington, D.C. - Four projects that will develop capabilities for designing sophisticated materials that can withstand the harsh environments of advanced fossil energy power systems have been selected by the U.S. Department of Energy. The projects will develop computational capabilities for designing materials with unique thermal, chemical and mechanical properties necessary for withstanding the high temperatures and extreme environments of advanced energy systems. These innovative systems are both fuel efficient and produce lower amounts of emissions, including carbon dioxide for permanent storage. An effective way to accelerate research is to use advances in materials simulations and high performance computing and communications to guide experiments. Concurrent with the continuing drive to reduce costs and design cycle time in the manufacture of power plant equipment is an increase in the need for more materials property data demonstrating sufficient performance.

267

DOE Selects Lawrence Livermore National Security, LLC to Manage its  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Lawrence Livermore National Security, LLC to Manage its Lawrence Livermore National Security, LLC to Manage its Lawrence Livermore National Laboratory DOE Selects Lawrence Livermore National Security, LLC to Manage its Lawrence Livermore National Laboratory May 8, 2007 - 12:45pm Addthis WASHINGTON, DC - The U.S. Department of Energy (DOE) today announced that Lawrence Livermore National Security, LLC (LLNS) has been selected to be the management and operating contractor for DOE's National Nuclear Security Administration's (NNSA) Lawrence Livermore National Laboratory in California. "Livermore National Laboratory is a critical part of our nuclear weapons complex and has been for the last 55 years," Secretary Bodman said. "For the first time since the beginning of the laboratory a new contractor is

268

Inside: Instruction selection/identification & design exploration for extensible processors  

E-Print Network (OSTI)

This paper presents the INSIDE system that rapidly searches the design space for extensible processors, given area and performance constraints of an embedded application, while minimizing the design turn-around-time. Our system consists of a) a methodology to determine which code segments are most suited for implementation as a set of extensible instructions, b) a heuristic algorithm to select pre-configured extensible processors as well as extensible instructions (library), and c) an estimation tool which rapidly estimates the performance of an application on a generated extensible processor. By selecting the right combination of a processor core plus extensible instructions, we achieve a performance increase on average of 2.03x (up to 7x) compared to the base processor core at a minimum hardware overhead of 25 % on average. 1.

Newton Cheung; Sri Parameswaran; Jörg Henkel

2002-01-01T23:59:59.000Z

269

Time Spectral Analysis of Midlatitude Disturbances in the Martian Atmosphere  

Science Conference Proceedings (OSTI)

The nature of the synoptic period variations in the Viking 2 pressure, wind and temperature data is investigated, using time-spectral and cross-spectral analysis, for selected portions of the Mars fall, winter and spring seasons. Estimates of the ...

Jeffrey R. Barnes

1980-09-01T23:59:59.000Z

270

New tensioning equipment saves critical path time in nuclear outage  

SciTech Connect

This article examines the selection and application of new tensioning equipment for TVA`s Browns Ferry Nuclear Plant. The new device would reduce refueling outage time and radiation exposure, and require fewer personnel to operate. Results of the equipment performance during the refueling outage and problems encountered and resolved are described.

NONE

1995-10-01T23:59:59.000Z

271

Analyses of Inhomogeneities in Radiosonde Temperature and Humidity Time Series  

Science Conference Proceedings (OSTI)

Twice daily radiosonde data from selected stations in the United States (period 1948 to 1990) and China (period 1958 to 1990) were sorted into time series. These stations have one sounding taken in darkness and the other in sunlight. The analysis ...

Panmao Zhai; Robert E. Eskridge

1996-04-01T23:59:59.000Z

272

Bayesian selection of non faulty sensors (SYS 6)  

E-Print Network (OSTI)

for Embedded Networked Sensing Bayesian Selection of non -Use MAP to select the Bayesian optimal sensor subset We

Kevin Ni; Greg Pottie

2006-01-01T23:59:59.000Z

273

Run-time optimization of adaptive irregular applications  

E-Print Network (OSTI)

Compared to traditional compile-time optimization, run-time optimization could o?er signi?cant performance improvements when parallelizing and optimizing adaptive irregular applications, because it performs program analysis and adaptive optimizations during program execution. Run-time techniques can succeed where static techniques fail because they exploit the characteristics of input data, programs' dynamic behaviors, and the underneath execution environment. When optimizing adaptive irregular applications for parallel execution, a common observation is that the effectiveness of the optimizing transformations depends on programs' input data and their dynamic phases. This dissertation presents a set of run-time optimization techniques that match the characteristics of programs' dynamic memory access patterns and the appropriate optimization (parallelization) transformations. First, we present a general adaptive algorithm selection framework to automatically and adaptively select at run-time the best performing, functionally equivalent algorithm for each of its execution instances. The selection process is based on off-line automatically generated prediction models and characteristics (collected and analyzed dynamically) of the algorithm's input data, In this dissertation, we specialize this framework for automatic selection of reduction algorithms. In this research, we have identi?ed a small set of machine independent high-level characterization parameters and then we deployed an off-line, systematic experiment process to generate prediction models. These models, in turn, match the parameters to the best optimization transformations for a given machine. The technique has been evaluated thoroughly in terms of applications, platforms, and programs' dynamic behaviors. Speci?cally, for the reduction algorithm selection, the selected performance is within 2% of optimal performance and on average is 60% better than "Replicated Buffer," the default parallel reduction algorithm speci?ed by OpenMP standard. To reduce the overhead of speculative run-time parallelization, we have developed an adaptive run-time parallelization technique that dynamically chooses effcient shadow structures to record a program's dynamic memory access patterns for parallelization. This technique complements the original speculative run-time parallelization technique, the LRPD test, in parallelizing loops with sparse memory accesses. The techniques presented in this dissertation have been implemented in an optimizing research compiler and can be viewed as effective building blocks for comprehensive run-time optimization systems, e.g., feedback-directed optimization systems and dynamic compilation systems.

Yu, Hao

2004-08-01T23:59:59.000Z

274

Process for selecting engineering tools : applied to selecting a SysML tool.  

SciTech Connect

Process for Selecting Engineering Tools outlines the process and tools used to select a SysML (Systems Modeling Language) tool. The process is general in nature and users could use the process to select most engineering tools and software applications.

De Spain, Mark J.; Post, Debra S. (Sandia National Laboratories, Livermore, CA); Taylor, Jeffrey L.; De Jong, Kent

2011-02-01T23:59:59.000Z

275

Selected Guidance & Requirements | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Selected Guidance & Requirements Selected Guidance & Requirements Selected Guidance & Requirements This page contains the most requested NEPA guidance and requirement documents and those most often recommended by the Office of NEPA Policy and Compliance. Documents are listed by agency, in reverse chronological order. More extensive collections of documents are available on the individual pages for Guidance and Requirements pages. Requirements - Statutes National Environmental Policy Act of 1969 Environmental Quality Improvement Act of 1970 Clean Air Act, Section 309 Guidance - Council on Environmental Quality NEPA at 19: A Primer on an "Old" Law with Solutions to New Problems 40 Most Asked Questions Concerning CEQ's NEPA Regulations Guidance - Department of Energy DOE, NEPA, and You

276

Selective catalyst reduction light-off strategy  

Science Conference Proceedings (OSTI)

An emissions control system includes a temperature determination module and an emissions control module. The temperature determination module determines a first temperature of a heater element of a diesel particulate filter (DPF) assembly in an exhaust system and determines a second temperature of a catalyst of the DPF assembly. The emissions control module selectively activates the heater element, selectively initiates a predefined combustion process in an engine based upon the first temperature, and selectively starts a reductant injection process based upon the second temperature.

Gonze, Eugene V [Pinckney, MI

2011-10-18T23:59:59.000Z

277

Bandlet Image Estimation with Model Selection  

E-Print Network (OSTI)

A new estimator is introduced to reduce white noise added to images having a geometrical regularity. This estimator projects the observations on orthogonal bandlet vectors selected in a dictionary of orthonormal bases. It is proved that the resulting risk is quasi asymptotically minimax for geometrically regular images. This paper is also a tutorial on estimation with general dictionary of orthogonal bases, through model selection. It explains how to build a thresholding estimator in a adaptively chosen ``best'' basis and gives a simple proof of its performance with the model selection approach of Barron, Birge and Massart

Dossal, Charles; Mallat, Stéphane

2008-01-01T23:59:59.000Z

278

Commissioning of the ATLAS Muon Trigger Selection  

E-Print Network (OSTI)

The performance of the three-level ATLAS muon trigger as evaluated by using LHC data is presented. Events have been selected by using only the hardware-based Level-1 trigger in order to commission and to subsequently enable the (software-based) selections of the High Level Trigger. Studies aiming at selecting prompt muons from J/{\\psi} and at reducing non prompt muon contamination have been performed. A brief overview on how the muon triggers evolve with increasing luminosity is given.

Musto, Elisa

2010-01-01T23:59:59.000Z

279

Commissioning of the ATLAS Muon Trigger Selection  

E-Print Network (OSTI)

The performance of the three-level ATLAS muon trigger as evaluated by using LHC data is presented. Events have been selected by using only the hardware-based Level-1 trigger in order to commission and to subsequently enable the (software-based) selections of the High Level Trigger. Studies aiming at selecting prompt muons from J/{\\psi} and at reducing non prompt muon contamination have been performed. A brief overview on how the muon triggers evolve with increasing luminosity is given.

Elisa Musto

2010-09-30T23:59:59.000Z

280

First-passage-time problems in time-aware networks  

E-Print Network (OSTI)

First passage time or the first time that a stochastic process crosses a boundary is a random variable whose probability distribution is sought in engineering, statistics, finance, and other disciplines. The probability ...

Suwansantisuk, Watcharapan, 1978-

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

NIST: A Walk Through Time - The "Atomic Age" of Time ...  

Science Conference Proceedings (OSTI)

... Transportation, communication, financial transactions, manufacturing, electric power and many ... The next generation of time standards is presently ...

2010-10-05T23:59:59.000Z

282

E-print Network : Your Selections  

Office of Scientific and Technical Information (OSTI)

Your Selections Back To Previous Page Selections - of First Page Previous Page Next Page Last Page Back To Previous Page You have 0 selections. Click the checkboxes clipping.addClipping on the results or alert results pages to add to your selections. Some links on this page may take you to non-federal websites. Their policies may differ from this site. U.S. Department of Energy U.S. Department of Energy Office of Science Office of Scientific and Technical Information Website Policies/Important Links Science Accelerator science.gov WorldWideScience.org Deep Web Technologies Email Results Use this form to email your search results * Email this to: * Your Name: Comments: URL only?: Number of results: 10 20 50 100 200 All Email Format: HTML TEXT * Required field Print Results

283

Selected AI-Related Dissertations Bibliography  

Science Conference Proceedings (OSTI)

The following are citations selected by title and abstract as being related to AI, resulting from a computer search, using BRS Information Technologies, of the Dissertation Abstracts Online database produced by University Microfilms International (UMI).The ...

Bob Krovetz; Susanne M. Humphrey

1991-07-01T23:59:59.000Z

284

National Library of Energy : Your Selections  

Office of Scientific and Technical Information (OSTI)

Your Selections Back To Previous Page Selections - of First Page Previous Page Next Page Last Page Back To Previous Page You have 0 selections. Click the checkboxes clipping.addClipping on the results or alert results pages to add to your selections. USDOE U.S. Department of Energy Office of Science Some links on this page may take you to non-federal websites. Their policies may differ from this site. Website Policies and Important Links Search capabilities provided by DOE/OSTI Deep Web Technologies Email Results Use this form to email your search results * Email this to: * Your Name: Comments: URL only?: Number of results: 10 20 50 100 200 All Email Format: HTML TEXT * Required field Print Results Use this form to print results. The page of currently displayed results.

285

Selected M-Related Dissertations Bibliography  

Science Conference Proceedings (OSTI)

The following are citations selected by title and abstract as being related to AI, resulting from a computer search, using BRS Information Technologies, of the Dissertation Abstracts Online data-base produced by University Microfilms International (UMI). ...

Susanne M. Humphrey; Bob Krovetz

1990-11-01T23:59:59.000Z

286

Sexual selection of co-operation  

Science Conference Proceedings (OSTI)

Advocates of sexual selection theory have argued that various male traits, such as male co-operative behavior towards females, can evolve through female preference for mating with those males who possess that trait. This paper reports on the results ...

M. Afzal Upal

2003-07-01T23:59:59.000Z

287

System architecture analysis and selection under uncertainty  

E-Print Network (OSTI)

A system architecture analysis and selection methodology is presented that builds on the Multidisciplinary Analysis and Optimization framework. It addresses a need and opportunity to extend the MAO techniques to include a ...

Smaling, Rudolf M

2005-01-01T23:59:59.000Z

288

Econometric structural models : a model selection approach.  

E-Print Network (OSTI)

??Using a model selection approach, this thesis proposes a constructive data-and-theory-combined procedure to identify model structures in the framework of a linear simultaneous equations system… (more)

Chen, Pu

2002-01-01T23:59:59.000Z

289

Selected M-Related Dissertations Bibliography  

Science Conference Proceedings (OSTI)

The following are citations selected by title and abstract as being related to AI, resulting from a computer search, using DIALOG Information Services, of the Dissertation Abstracts Online database produced by University Microfilms International (UMI). ...

Susanne M. Humphrey; Bob Krovetz

1990-10-01T23:59:59.000Z

290

Microgrid Selection and Operation for Commercial  

E-Print Network (OSTI)

LBNL-313E Microgrid Selection and Operation for Commercial Buildings in California and New York---GGGrrriiiddd CCCooonnnfffeeerrreeennnccceee,,, GGGlllyyyfffaaadddaaa,,, GGGrrreeeeeeccceee,,, 222999­­­333000 MMMaaayyy 222000000888 Microgrid

291

Release Time Scheduling and Hub Location for Next-Day Delivery  

Science Conference Proceedings (OSTI)

Inspired by a real-life problem faced by one of the largest ground-based cargo companies of Turkey, the current study introduces a new facet to the hub location literature. The release time scheduling and hub location problem aims to select a specified ... Keywords: cargo delivery, hub location, release times, time definite delivery, valid inequalities

Hande Yaman; Oya Ekin Karasan; Bahar Y. Kara

2012-07-01T23:59:59.000Z

292

Review of Selected Home Energy Auditing Tools  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

REVIEW OF SELECTED HOME REVIEW OF SELECTED HOME ENERGY AUDITING TOOLS In Support of the Development of a National Building Performance Assessment and Rating Program Prepared for: The U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy Prepared by: SENTECH, Inc. (now part of SRA International, Inc.) November 2, 2010 TABLE OF CONTENTS TABLE OF CONTENTS ....................................................................................................... 2 1. EXECUTIVE SUMMARY .......................................................................................... 3 2. INTRODUCTION ............................................................................................................. 4 3. ENERGY AUDIT TOOL TYPES ................................................................................. 5

293

Heat Recovery Steam Generator Materials Selection Guideline  

Science Conference Proceedings (OSTI)

Materials selection is both an art and a science. There is no single material that is the optimal choice for a given application. For example, subtle changes such as the design, fabrication, and quality control specification for a high-pressure superheater (HPSH) tube-to-header connection can alter the choice of the optimal tube material. Minor changes to the component's operating environment can also alter the materials selection choice. What was an ideal tube material in a baseloaded heat recovery stea...

2011-12-21T23:59:59.000Z

294

Drug delivery from hydrophobic-modified mesoporous silicas: Control via modification level and site-selective modification  

SciTech Connect

Dimethylsilyl (DMS) modified mesoporous silicas were successfully prepared via co-condensation and post-grafting modification methods. The post-grafting modification was carried out by the reaction of the as-synthesized MCM-41 material (before CTAB removal) with diethoxydimethylsinale (DEDMS). N{sub 2} adsorption-desorption and {sup 29}Si MAS NMR characterization demonstrated that different amount of DMS groups were successfully incorporated into the co-condensation modified samples, and the functional DMS groups were placed selectively on the pore openings and external pore surfaces in the post-grafting modified samples. Subsequently, the controlled drug delivery properties from the resulting DMS-modified mesoporous silicas were investigated in detail. The drug adsorption experiments showed that the adsorption capacities were mainly depended on the content of silanol group (CSG) in the corresponding carriers. The in vitro tests exhibited that the incorporation of DMS groups greatly retarded the ibuprofen release rate. Moreover, the ibuprofen release profiles could be well modulated by varying DMS modification levels and site-selective distribution of functional groups in mesoporous carriers. - The distribution of DMS groups on the pore surfaces of the mesostructures strongly affects the drug release rate. The P-M41-1 and the P-M41-2 possess the close DMS modification levels as the C-M41-10, but the ibuprofen release rates from the P-M41-1 and P-M41-2 are much slower than that from the C-M41-10.

Tang Qunli, E-mail: tangqunli@hnu.c [College of Materials Science and Engineering, and Center for High-Resolution Electron Microscopy, Hunan University, Changsha 410082 (China); State Key Laboratory of Coal Conversion, Institute of Coal Chemistry, Chinese Academy of Sciences, Taiyuan 030001 (China); Chen Yuxi; Chen Jianghua; Li Jin [College of Materials Science and Engineering, and Center for High-Resolution Electron Microscopy, Hunan University, Changsha 410082 (China); Xu Yao; Wu Dong; Sun Yuhan [State Key Laboratory of Coal Conversion, Institute of Coal Chemistry, Chinese Academy of Sciences, Taiyuan 030001 (China)

2010-01-15T23:59:59.000Z

295

A high dimensional delay selection for the reconstruction of proper phase space with cross auto-correlation  

Science Conference Proceedings (OSTI)

For the purpose of phase space reconstruction from nonlinear time series, delay selection is one of the most vital criteria. This is normally done by using a general measure viz., mutual information (MI). However, in that case, the delay selection is ... Keywords: Cross auto-correlation, Dynamical system, Phase space reconstructions, Shape distortion measure

Sanjay Kumar Palit, Sayan Mukherjee, D. K. Bhattacharya

2013-08-01T23:59:59.000Z

296

Descriptions of Past Research in Program 80: New Combustion Turbine/Combined-Cycle Plant Design and Technology Selection  

Science Conference Proceedings (OSTI)

BackgroundAt a time when the power industry needs to meet growing demand and capacity requirements, informed decisions on gas turbine selection and plant designs are especially important. Technology selection impacts efficiency, emissions, availability, maintainability, and durability. Flexible operational capabilities are needed for plant dispatch, and planners need to understand upcoming trends and potential improvements for future growth.The Electric Power ...

2012-09-19T23:59:59.000Z

297

PHYSICAL REVIEW A 86, 023402 (2012) Dissociation dynamics of diatomic molecules in intense laser fields: A scheme for the selection  

E-Print Network (OSTI)

fields: A scheme for the selection of relevant adiabatic potential curves M. Magrakvelidze,1 C. M. Aikens of the molecular ion. For H2 + , the dissociative wave packet emerges mainly on the repulsive |2pu state, while times in a given electronic state serve as a first criterion for selecting relevant potential curves

Thumm, Uwe

298

Meteorology: typical meteorological year data for selected stations in  

Open Energy Info (EERE)

Kenya from NREL Kenya from NREL Dataset Summary Description (Abstract): Each TMY is a data set of hourly values of solar radiation and meteorological elements for a 1-year period. Solar radiation is modeled using the NREL METSTAT model, with surface observed cloud cover being the principal model input. The container file contains one TMY file for each selected station in the region, plus documentation files and a TMY data reader file for use with Microsoft Excel. (Purpose): Simulations (Supplemental Information): A TMY consists of months selected from individual years and concatenated to form a complete year. The intended use is for computer simulations of solar energy conversion systems and building systems. Because of the selection criteria, these TMYs are not appropriate for simulations of wind energy conversion systems. A TMY provides a standard for hourly data for solar radiation and other meteorological elements that permit performance comparisons of system types and configurations for one or more locations. A TMY is not necessarily a good indicator of conditions over the next year, or even the next 5 years. Rather, it represents conditions judged to be typical over a long period of time, such as 30 years. Because they represent typical rather than extreme conditions, they are not suited for designing systems and their components to meet the worst-case conditions occurring at a location.

299

Meteorology: typical meteorological year data for selected stations in  

Open Energy Info (EERE)

Ethiopia from NREL Ethiopia from NREL Dataset Summary Description (Abstract): Each TMY is a data set of hourly values of solar radiation and meteorological elements for a 1-year period. Solar radiation is modeled using the NREL METSTAT model, with surface observed cloud cover being the principal model input. The container file contains one TMY file for each selected station in the region, plus documentation files and a TMY data reader file for use with Microsoft Excel. (Purpose): Simulations (Supplemental Information): A TMY consists of months selected from individual years and concatenated to form a complete year. The intended use is for computer simulations of solar energy conversion systems and building systems. Because of the selection criteria, these TMYs are not appropriate for simulations of wind energy conversion systems. A TMY provides a standard for hourly data for solar radiation and other meteorological elements that permit performance comparisons of system types and configurations for one or more locations. A TMY is not necessarily a good indicator of conditions over the next year, or even the next 5 years. Rather, it represents conditions judged to be typical over a long period of time, such as 30 years. Because they represent typical rather than extreme conditions, they are not suited for designing systems and their components to meet the worst-case conditions

300

Meteorology: typical meteorological year data for selected stations in  

Open Energy Info (EERE)

Brazil from NREL Brazil from NREL Dataset Summary Description (Abstract): Each TMY is a data set of hourly values of solar radiation and meteorological elements for a 1-year period. Solar radiation is modeled using the NREL METSTAT model, with surface observed cloud cover being the principal model input. The container file contains one TMY file for each selected station in the region, plus documentation files and a TMY data reader file for use with Microsoft Excel. (Purpose): Simulations (Supplemental Information): A TMY consists of months selected from individual years and concatenated to form a complete year. The intended use is for computer simulations of solar energy conversion systems and building systems. Because of the selection criteria, these TMYs are not appropriate for simulations of wind energy conversion systems. A TMY provides a standard for hourly data for solar radiation and other meteorological elements that permit performance comparisons of system types and configurations for one or more locations. A TMY is not necessarily a good indicator of conditions over the next year, or even the next 5 years. Rather, it represents conditions judged to be typical over a long period of time, such as 30 years. Because they represent typical rather than extreme conditions, they are not suited for designing systems and their components to meet the worst-case conditions occurring at a location.

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Meteorology: typical meteorological year data for selected stations in  

Open Energy Info (EERE)

Nepal from NREL Nepal from NREL Dataset Summary Description (Abstract): Each TMY is a data set of hourly values of solar radiation and meteorological elements for a 1-year period. Solar radiation is modeled using the NREL METSTAT model, with surface observed cloud cover being the principal model input. The container file contains one TMY file for each selected station in the region, plus documentation files and a TMY data reader file for use with Microsoft Excel. (Purpose): Simulations (Supplemental Information): A TMY consists of months selected from individual years and concatenated to form a complete year. The intended use is for computer simulations of solar energy conversion systems and building systems. Because of the selection criteria, these TMYs are not appropriate for simulations of wind energy conversion systems. A TMY provides a standard for hourly data for solar radiation and other meteorological elements that permit performance comparisons of system types and configurations for one or more locations. A TMY is not necessarily a good indicator of conditions over the next year, or even the next 5 years. Rather, it represents conditions judged to be typical over a long period of time, such as 30 years. Because they represent typical rather than extreme conditions, they are not suited for designing systems and their components to meet the worst-case conditions occurring at a location.

302

Biofuel Feedstock Assessment For Selected Countries  

SciTech Connect

Findings from biofuel feedstock production assessments and projections of future supply are presented and discussed. The report aims to improve capabilities to assess the degree to which imported biofuel could contribute to meeting future U.S. targets to reduce dependence on imported oil. The study scope was focused to meet time and resource requirements. A screening process identified Argentina, Brazil, Canada, China, Colombia, India, Mexico, and the Caribbean Basin Initiative (CBI) region for initial analysis, given their likely role in future feedstock supply relevant to U.S. markets. Supply curves for selected feedstocks in these countries are projected for 2012, 2017 and 2027. The supply functions, along with calculations to reflect estimated supplies available for export and/or biofuel production, were provided to DOE for use in a broader energy market allocation study. Potential cellulosic supplies from crop and forestry residues and perennials were also estimated for 2017 and 2027. The analysis identified capacity to potentially double or triple feedstock production by 2017 in some cases. A majority of supply growth is derived from increasing the area cultivated (especially sugarcane in Brazil). This is supplemented by improving yields and farming practices. Most future supplies of corn and wheat are projected to be allocated to food and feed. Larger shares of future supplies of sugarcane, soybean and palm oil production will be available for export or biofuel. National policies are catalyzing investments in biofuel industries to meet targets for fuel blending that generally fall in the 5-10% range. Social and environmental concerns associated with rapid expansion of feedstock production are considered. If the 2017 projected feedstock supply calculated as 'available' for export or biofuel were converted to fuel, it would represent the equivalent of about 38 billion gallons of gasoline. Sugarcane and bagasse dominate the available supply, representing 64% of the total. Among the nations studied, Brazil is the source of about two-thirds of available supplies, followed distantly by Argentina (12%), India and the CBI region.

Kline, Keith L [ORNL; Oladosu, Gbadebo A [ORNL; Wolfe, Amy K [ORNL; Perlack, Robert D [ORNL; Dale, Virginia H [ORNL

2008-02-01T23:59:59.000Z

303

PEP-II injection timing and controls  

SciTech Connect

Hardware has been built and software written and incorporated in the existing SLC accelerator control system to control injection of beam pulses from the accelerator into the PEP-II storage rings currently under construction. Hardware includes a CAMAC module to delay the machine timing fiducial in order that a beam pulse extracted from a damping ring will be injected into a selected group of four 476 MHz buckets in a PEP-II ring. Further timing control is accomplished by shifting the phase of the bunches stored in the damping rings before extraction while leaving the phase of the PEP-II stored beam unchanged. The software which drives timing devices on a pulse-to-pulse basis relies on a dedicated communication link on which one scheduling microprocessor broadcasts a 128-bit message to all distributed control microprocessors at 360 Hz. PEP-II injection will be driven by the scheduling microprocessor according to lists specifying bucket numbers in arbitrary order, and according to scheduling constraints maximizing the useful beam delivered to the SLC collider currently in operation. These lists will be generated by a microprocessor monitoring the current stored per bucket in each of the PEP-II rings.

Bharadwaj, V.; Browne, M.; Crane, M.; Gromme, T.; Himel, T.; Ross, M.; Stanek, M. [Stanford Linear Accelerator Center, Menlo Park, CA (United States); Ronan, M. [Lawrence Berkeley National Lab., CA (United States)

1997-07-01T23:59:59.000Z

304

NIST Time Scale Data Archive  

Science Conference Proceedings (OSTI)

NIST Time Scale Data Archive. Updated monthly. Return to Archive index Leap second and UT1-UTC information. This page ...

2013-08-07T23:59:59.000Z

305

Personalised time-dependent learning  

Science Conference Proceedings (OSTI)

Time-dependent instruction appears to shape next-generation learning systems, where the value of instruction is as important as the time it takes to learn. The ability to grasp the exact knowledge required to accomplish a specific task, in the ... Keywords: adaptive learning, authoring tools, knowledge management, learning granularity, learning objects, learning resources, learning technology, learning web, ontology, personalised learning, semantic web, time constraints, time-dependent learning, timeliness

R. Benlamri; Y. Atif; J. Berri

2009-04-01T23:59:59.000Z

306

Timing-Driven Partial Scan  

Science Conference Proceedings (OSTI)

We present a partial scan approach, which aims at reducing both area overhead and performance degradation caused by test logic. Given a target speed and an initial design that meets the target, the algorithm selects a minimum set of scan flip-flops, ... Keywords: Test algorithms, partial scan, test synthesis, design for test

Jing-yang Jou; Kwang-ting (tim) Cheng

1995-12-01T23:59:59.000Z

307

The LCLS Timing Event System  

Science Conference Proceedings (OSTI)

The Linac Coherent Light Source requires precision timing trigger signals for various accelerator diagnostics and controls at SLAC-NAL. A new timing system has been developed that meets these requirements. This system is based on COTS hardware with a mixture of custom-designed units. An added challenge has been the requirement that the LCLS Timing System must co-exist and 'know' about the existing SLC Timing System. This paper describes the architecture, construction and performance of the LCLS timing event system.

Dusatko, John; Allison, S.; Browne, M.; Krejcik, P.; /SLAC

2012-07-23T23:59:59.000Z

308

Time  

NLE Websites -- All DOE Office Websites (Extended Search)

Judges 9:00- 9:25 Materials Science Mathew Cherukara Shock Induced Chemistry of NiAl Nano-Composites Chen, X. Gyrya, V. 9:25- 9:50 Materials Science Christian Sorensen Explosive...

309

The Selection Function of SZ Cluster Surveys  

E-Print Network (OSTI)

We study the nature of cluster selection in Sunyaev-Zel'dovich (SZ) surveys, focusing on single frequency observations and using Monte Carlo simulations incorporating instrumental effects, primary cosmic microwave background (CMB) anisotropies and extragalactic point sources. Clusters are extracted from simulated maps with an optimal, multi-scale matched filter. We introduce a general definition for the survey selection function that provides a useful link between an observational catalog and theoretical predictions. The selection function defined over the observed quantities of flux and angular size is independent of cluster physics and cosmology, and thus provides a useful characterization of a survey. Selection expressed in terms of cluster mass and redshift, on the other hand, depends on both cosmology and cluster physics. We demonstrate that SZ catalogs are not simply flux limited, and illustrate how incorrect modeling of the selection function leads to biased estimates of cosmological parameters. The fact that SZ catalogs are not flux limited complicates survey ``calibration'' by requiring more detailed information on the relation between cluster observables and cluster mass.

J. -B. Melin; J. G. Bartlett; J. Delabrouille

2004-09-23T23:59:59.000Z

310

All Time, All the Time: Improving NIST Radio  

Science Conference Proceedings (OSTI)

... need for manual adjustments when Daylight Saving Time begins and ends, and allowing automatic resetting of clocks following a power outage.

2011-10-06T23:59:59.000Z

311

A Time Bucket Formulation for the TSP with Time Windows  

E-Print Network (OSTI)

Nov 5, 2009 ... Abstract: The Traveling Salesman Problem with Time Windows (TSPTW) is the problem of finding a minimum-cost path visiting a set of cities ...

312

NIST: A Walk Through Time - World Time Scales  

Science Conference Proceedings (OSTI)

... A Walk Through Time - Home Page ... and technologists recognized the inadequacy of timekeeping based on the motion of the Earth, which fluctuates ...

2010-10-05T23:59:59.000Z

313

Intrinsic and Cosmological Signatures in Gamma-Ray Burst Time Profiles: Time Dilation  

E-Print Network (OSTI)

The time profiles of many gamma-ray bursts consist of distinct pulses, which offers the possibility of characterizing the temporal structure of these bursts using a relatively small set of pulse shape parameters. We have used a pulse decomposition procedure to analyze the Time-to-Spill (TTS) data for all bursts observed by BATSE up through trigger number 2000, in all energy channels for which TTS data is available. We obtain amplitude, rise and decay timescales, a pulse shape parameter, and the fluences of individual pulses in all of the bursts. We investigate the correlations between brightness measures (amplitude and fluence) and timescale measures (pulse width and separation) which may result from cosmological time dilation of bursts, or from intrinsic properties of burst sources or from selection effects. The effects of selection biases are evaluated through simulations. The correlations between these parameters among pulses within individual bursts give a measure of the intrinsic effects while the correlations among bursts could result both from intrinsic and cosmological effects. We find that timescales tend to be shorter in bursts with higher peak fluxes, as expected from cosmological time dilation effects, but also find that there are non-cosmological effects contributing to this inverse correlation. We find that timescales tend to be longer in bursts with higher total fluences, contrary to what is expected from cosmological effects. We also find that peak fluxes and total fluences of bursts are uncorrelated, indicating that they cannot both be good distance indicators for bursts. Subject headings: gamma rays: bursts—cosmology: theory

Andrew Lee; Elliott D. Bloom; Vahé Petrosian

2000-01-01T23:59:59.000Z

314

ENSEMBLE VARIABILITY OF NEAR-INFRARED-SELECTED ACTIVE GALACTIC NUCLEI  

Science Conference Proceedings (OSTI)

We present the properties of the ensemble variability V for nearly 5000 near-infrared active galactic nuclei (AGNs) selected from the catalog of Quasars and Active Galactic Nuclei (13th Edition) and the SDSS-DR7 quasar catalog. From three near-infrared point source catalogs, namely, Two Micron All Sky Survey (2MASS), Deep Near Infrared Survey (DENIS), and UKIDSS/LAS catalogs, we extract 2MASS-DENIS and 2MASS-UKIDSS counterparts for cataloged AGNs by cross-identification between catalogs. We further select variable AGNs based on an optimal criterion for selecting the variable sources. The sample objects are divided into subsets according to whether near-infrared light originates by optical emission or by near-infrared emission in the rest frame; and we examine the correlations of the ensemble variability with the rest-frame wavelength, redshift, luminosity, and rest-frame time lag. In addition, we also examine the correlations of variability amplitude with optical variability, radio intensity, and radio-to-optical flux ratio. The rest-frame optical variability of our samples shows negative correlations with luminosity and positive correlations with rest-frame time lag (i.e., the structure function, SF), and this result is consistent with previous analyses. However, no well-known negative correlation exists between the rest-frame wavelength and optical variability. This inconsistency might be due to a biased sampling of high-redshift AGNs. Near-infrared variability in the rest frame is anticorrelated with the rest-frame wavelength, which is consistent with previous suggestions. However, correlations of near-infrared variability with luminosity and rest-frame time lag are the opposite of these correlations of the optical variability; that is, the near-infrared variability is positively correlated with luminosity but negatively correlated with the rest-frame time lag. Because these trends are qualitatively consistent with the properties of radio-loud quasars reported by some previous studies, most of our sample objects are probably radio-loud quasars. Finally, we also discuss the negative correlations seen in the near-infrared SFs.

Kouzuma, S. [School of International Liberal Studies, Chukyo University, Toyota 470-0393 (Japan); Yamaoka, H., E-mail: skouzuma@lets.chukyo-u.ac.jp, E-mail: yamaoka@phys.kyushu-u.ac.jp [Department of Physics, Kyushu University, Fukuoka 812-8581 (Japan)

2012-03-01T23:59:59.000Z

315

A method for discriminative particle selection  

DOE Patents (OSTI)

The invention is a method and means for separating ions or providing an ion beam. The invention generates ions of the isotopes to be separated, and then provides a traveling electric potential hill created by a sequential series of quasi static electric potential hills. By regulating the velocity and potential amplitude of the traveling electric potential hill ionized isotopes are selectively positively or negatively accelerated. Since the ionized isotopes have differing final velocities, the isotopes may be collected separately or used to produce an ion beam of a selected isotope.

Post, R.F.

1990-10-05T23:59:59.000Z

316

Thermophotovoltaic emitter material selection and design  

DOE Green Energy (OSTI)

Thermophotovoltaics (TPV) is a potentially attractive direct energy conversion technology. It reduces the need for complex machinery with moving parts and maintenance. TPV generators can be run from a variety of heat sources including waste heat for smaller scale operations. The US Naval Academy`s goal was to build a small experimental thermophotovoltaic generator powered by combustion gases from a General Electric T-58 helicopter gas turbine. The design of the generator imposes material limitations that directly affect emitter and structural materials selection. This paper details emitter material goals and requirements, and the methods used to select suitable candidate emitter materials for further testing.

Saxton, P.C.; Moran, A.L.; Harper, M.J.; Lindler, K.W. [Naval Academy, Annapolis, MD (United States)

1997-07-01T23:59:59.000Z

317

Selective Sorbents For Purification Of Hydrocarbons  

DOE Patents (OSTI)

A method for removing thiophene and thiophene compounds from liquid fuel includes contacting the liquid fuel with an adsorbent which preferentially adsorbs the thiophene and thiophene compounds. The adsorption takes place at a selected temperature and pressure, thereby producing a non-adsorbed component and a thiophene/thiophene compound-rich adsorbed component. The adsorbent includes either a metal or a metal ion that is adapted to form p-complexation bonds with the thiophene and/or thiophene compounds, and the preferential adsorption occurs by p-complexation. A further method includes selective removal of aromatic compounds from a mixture of aromatic and aliphatic compounds.

Yang, Ralph T. (Ann Arbor, MI); Yang, Frances H. (Ann Arbor, MI); Takahashi, Akira (Yoko-Machi, JP); Hernandez-Maldonado, Arturo J. (Ann Arbor, MI)

2006-04-18T23:59:59.000Z

318

Appendix: Selected Answers Section 1.2  

E-Print Network (OSTI)

Appendix: Selected Answers Chapter 1 Section 1.2 1.2.1 (a) 5/6. (b) 1. (c) 1/2. 1.2.4 No. 1.2.8 No/4. 1.6.3 limn P(An) = P(A) = P(S) = 1. 1 #12;2 APPENDIX: SELECTED ANSWERS Chapter 2 Section 2.1 2.1.1(a Negative Binomial(r + s, ) . Section 2.4 2.4.1 (a) P(U 0) = 0. (b) P(U = 1/2) = 0. (c) P(U

Rosenthal, Jeffrey S.

319

Time-lock Puzzles and Timed-release Crypto  

Science Conference Proceedings (OSTI)

Our motivation is the notion of ``timed-release crypto,'''' where the goal is to encrypt a message so that it can not be decrypted by anyone, not even the sender, until a pre-determined amount of time has passed. The goal is to ``send information into ...

R. L. Rivest; A. Shamir; D. A. Wagner

1996-02-01T23:59:59.000Z

320

Reactor control rod timing system  

DOE Patents (OSTI)

A fluid driven jet-edge whistle timing system for control rods of a nuclear reactor for producing real-time detection of the timing of each control rod in its scram operation. An important parameter in reactor safety, particularly for liquid metal fast breeder reactors (LMFBR), is the time deviation between the time the control rod is released and the time the rod actually reaches the down position. The whistle has a nearly pure tone signal with center frequency (above 100 kHz) far above the frequency band in which the energy of the background noise is concentrated. Each control rod can be fitted with a whistle with a different frequency so that there is no ambiguity in differentiating the signal from each control rod.

Wu, Peter T. K. (Clifton Park, NY)

1982-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Essays in time and risk  

E-Print Network (OSTI)

lists yield systematically higher discount rates and utilityList methodology: identifying time preferences with MPLs and utilityrisk price list to inform curvature of the utility function

Sprenger, Charles

2011-01-01T23:59:59.000Z

322

Time-critical information services  

Science Conference Proceedings (OSTI)

Emergency medical services have never been more ready for the implementation of time-critical interorganizational information services for the public good.

Thomas A. Horan; Benjamin L. Schooley

2007-03-01T23:59:59.000Z

323

Time and Frequency Users Manual  

Science Conference Proceedings (OSTI)

... 9 TERMS USED 11 ... 135 GLOSSARY 137 INDEX ... The OIL INDUSTRY needs accurate timing to help automate oil well drilling, especially offshore. ...

2002-01-02T23:59:59.000Z

324

Automated Computer Time Service (ACTS)  

Science Conference Proceedings (OSTI)

... provided since 1988 for users who need to synchronize computer clocks to ... For computers with Internet access, the Internet Time Service should be ...

2013-02-22T23:59:59.000Z

325

Real time wind turbine simulator.  

E-Print Network (OSTI)

??A novel dynamic real-time wind turbine simulator (WTS) is developed in this thesis, which is capable of reproducing dynamic behavior of real wind turbine. The… (more)

Gong, Bing

2007-01-01T23:59:59.000Z

326

Multi-objective semi-supervised feature selection and model selection based on Pearson's correlation coefficient  

Science Conference Proceedings (OSTI)

This paper presents a Semi-Supervised Feature Selection Method based on a univariate relevance measure applied to a multiobjective approach of the problem. Along the process of decision of the optimal solution within Pareto-optimal set, atempting to ... Keywords: Pearson, feature selection, relief, semi-supervised

Frederico Coelho; Antonio Padua Braga; Michel Verleysen

2010-11-01T23:59:59.000Z

327

A Simulator for Timed CSP  

E-Print Network (OSTI)

Time is an integral aspect of computer systems. It is essential for modelling a system’s performance, but may also affect its safety or security. Timed CSP [Sch00] conservatively extends the process algebra CSP with timed primitives, where real numbers ? 0 model how time passes with reference to a single, conceptually global, clock. While there have been approaches for model checking Timed CSP ([Sch00, DHSZ06]), to the best of our knowledge we are the first to present a simulator for Timed CSP. Here, we restrict time to rational values only. Theoretically, this limits the expressibility of the language. Practically, this limitation turns out to be negligible (for instance all examples of Schneider’s book [Sch00] can be dealt with in our simulator). The simulator is the outcome of an undergraduate project at Swansea University [Dra11]. Our Timed CSP simulator extends the open source tool ProB [Leu]. ProB’s CSP simulator works as follows: The CSP specification is analyzed by a parser (written in Haskell) and translated to a representation in Prolog. A CSP Interpreter (in Prolog) stores the “firing rules” of CSP’s operational semantics. The Simulator (also in Prolog) determines the actions available and the resultant states. A GUI (written in Tcl/Tk) allows the user to interact with the Simulator. Timed CSP is closed under rational time [DNR11]. Consider, for example, the following firing rule ( t ? stands for a timed transition of duration t): P d? ? P ? (P ?d Q) d?

Marc Dragon; Andy Gimblett; Markus Roggenbach; Jens Bendisposto; Cliff Jones; Michael Leuschel; Er Romanovsky; Tiziana Margaria; Julia Padberg; Gabriele Taentzer; Marc Dragon; Andy Gimblett; Markus Roggenbach

2011-01-01T23:59:59.000Z

328

Selective flotation of inorganic sulfides from coal  

DOE Patents (OSTI)

Pyritic sulfur is removed from coal or other carbonaceous material through the use of humic acid as a coal flotation depressant. Following the removal of coarse pyrite, the carbonaceous material is blended with humic acid, a pyrite flotation collector and a frothing agent within a flotation cell to selectively float pyritic sulfur leaving clean coal as an underflow.

Miller, Kenneth J. (Floreffe, PA); Wen, Wu-Wey (Murrysville, PA)

1989-01-01T23:59:59.000Z

329

Selective epitaxy using the GILD process  

DOE Patents (OSTI)

The present invention comprises a method of selective epitaxy on a semiconductor substrate. The present invention provides a method of selectively forming high quality, thin GeSi layers in a silicon circuit, and a method for fabricating smaller semiconductor chips with a greater yield (more error free chips) at a lower cost. The method comprises forming an upper layer over a substrate, and depositing a reflectivity mask which is then removed over selected sections. Using a laser to melt the unmasked sections of the upper layer, the semiconductor material in the upper layer is heated and diffused into the substrate semiconductor material. By varying the amount of laser radiation, the epitaxial layer is formed to a controlled depth which may be very thin. When cooled, a single crystal epitaxial layer is formed over the patterned substrate. The present invention provides the ability to selectively grow layers of mixed semiconductors over patterned substrates such as a layer of Ge{sub x}Si{sub 1-x} grown over silicon. Such a process may be used to manufacture small transistors that have a narrow base, heavy doping, and high gain. The narrowness allows a faster transistor, and the heavy doping reduces the resistance of the narrow layer. The process does not require high temperature annealing; therefore materials such as aluminum can be used. Furthermore, the process may be used to fabricate diodes that have a high reverse breakdown voltage and a low reverse leakage current.

Weiner, K.H.

1990-12-31T23:59:59.000Z

330

Annual Operation of Selective Catalytic Reduction Systems  

Science Conference Proceedings (OSTI)

In 2009, many coal-fired generating units equipped with selective catalytic reduction (SCR) systems for nitrogen oxide (NOX) control will convert from seasonal to annual SCR operation. This report provides guidelines on how to prepare for annual operation. It focuses on existing experience with annual operation, catalyst management strategy, equipment reliability, cold weather issues, low load and cycling operation, and risk assessment.

2007-12-18T23:59:59.000Z

331

Selective spatio-temporal interest points  

Science Conference Proceedings (OSTI)

Recent progress in the field of human action recognition points towards the use of Spatio-Temporal Interest Points (STIPs) for local descriptor-based recognition strategies. In this paper, we present a novel approach for robust and selective STIP detection, ... Keywords: Action recognition, Bag-of-words, Complex scenes, Local descriptors, Multiple actors, Spatio-temporal interest points, Support vector machines

Bhaskar Chakraborty; Michael B. Holte; Thomas B. Moeslund; Jordi Gonzílez

2012-03-01T23:59:59.000Z

332

Acridine-intercalator based hypoxia selective cytotoxins  

DOE Patents (OSTI)

Hypoxia selective cytotoxins of the general formula STR1 wherein n is from 1 to 5, and NO[sub 2] is in at least one of the 2, 4 or 5-positions of the imidazole are developed. Such compounds have utility as radiosensitizers and chemosensitizers. 9 figs.

Papadopoulou-Rosenzweig, M.; Bloomer, W.D.

1994-03-15T23:59:59.000Z

333

Ligand iron catalysts for selective hydrogenation  

SciTech Connect

Disclosed are iron ligand catalysts for selective hydrogenation of aldehydes, ketones and imines. A catalyst such as dicarbonyl iron hydride hydroxycyclopentadiene) complex uses the OH on the five member ring and hydrogen linked to the iron to facilitate hydrogenation reactions, particularly in the presence of hydrogen gas.

Casey, Charles P. (Madison, WI); Guan, Hairong (Cincinnati, OH)

2010-11-16T23:59:59.000Z

334

Color selective photodetector and methods of making  

DOE Patents (OSTI)

A photoelectric device, such as a photodetector, can include a semiconductor nanowire electrostatically associated with a J-aggregate. The J-aggregate can facilitate absorption of a desired wavelength of light, and the semiconductor nanowire can facilitate charge transport. The color of light detected by the device can be chosen by selecting a J-aggregate with a corresponding peak absorption wavelength.

Walker, Brian J.; Dorn, August; Bulovic, Vladimir; Bawendi, Moungi G.

2013-03-19T23:59:59.000Z

335

Best routes selection in international intermodal networks  

Science Conference Proceedings (OSTI)

This study focuses on one of the intermodal operational issues: how to select best routes for shipments through the international intermodal network. International intermodal routing is complicated by three important characteristics: (1) multiple objectives; ... Keywords: Economies of scale, Intermodal, Multicommodity, Multiobjective

Tsung-Sheng Chang

2008-09-01T23:59:59.000Z

336

Path selection in multi-layer networks  

Science Conference Proceedings (OSTI)

Multi-layer networks are computer networks where the configuration of the network can be changed dynamically at multiple layers. However, in practice, technologies at different layers may be incompatible to each other, which necessitates a careful choice ... Keywords: Multi-layer network, Network description, Path selection

Fernando Kuipers; Freek Dijkstra

2009-01-01T23:59:59.000Z

337

2001 Workshop on Selective Catalytic Reduction  

Science Conference Proceedings (OSTI)

Approximately 100,000 megawatts of coal-fired capacity in the United States will employ selective catalytic reduction (SCR) for the control of nitrogen oxides (NOx) emissions by 2004. The 2001 Workshop on SCR, held in Baltimore, Maryland, provided a forum for discussion of current SCR issues.

2002-02-04T23:59:59.000Z

338

Selective flotation of inorganic sulfides from coal  

DOE Patents (OSTI)

Pyritic sulfur is removed from coal or other carbonaceous material through the use of humic acid as a coal flotation depressant. Following the removal of coarse pyrite, the carbonaceous material is blended with humic acid, a pyrite flotation collector and a frothing agent within a flotation cell to selectively float pyritic sulfur leaving clean coal as an underflow. 1 fig., 2 tabs.

Miller, K.J.; Wen, Wu-Wey

1988-05-31T23:59:59.000Z

339

Moving and Marking Selected Messages Shortcut Action  

E-Print Network (OSTI)

:amy OR lee From either Amy or Lee - (hyphen) Exclude terms from search subject:order ­new Subject contains Messages List Shortcut Action x Select message Enter or o Open currently focused message ( ) Shift + o Open + Enter Send the message Ctrl + s Save the message as a draft y or e Archive message (y removes label when

Hu, Jie

340

ALICE Trigger and Event Selection QA  

E-Print Network (OSTI)

I will present the last nine weeks of work on building a class that efficiently produces trending physics selection of various trigger classes for the purposes of quality assurance. This class is easily generalizable and will be used for live monitoring via a webpage.

CERN. Geneva

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Report on HVAC Option Selections for a Relocatable Classroom...  

NLE Websites -- All DOE Office Websites (Extended Search)

Report on HVAC Option Selections for a Relocatable Classroom Energy and Indoor Environmental Quality Field Study Title Report on HVAC Option Selections for a Relocatable Classroom...

342

Projects Selected for Funding Under the Joint NYSERDA / DOE Energy...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Projects Selected for Funding Under the Joint NYSERDA DOE Energy Storage Initiative Projects Selected for Funding Under the Joint NYSERDA DOE Energy Storage Initiative New York...

343

NETL: News Release -Four Minority Universities Selected for Fossil...  

NLE Websites -- All DOE Office Websites (Extended Search)

Four Minority Universities Selected for Fossil Energy Research Grants WASHINGTON, DC - The Department of Energy has selected four universities to receive grants under the...

344

DOE Office of Nuclear Energy Transportation Planning, Route Selection...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Office of Nuclear Energy Transportation Planning, Route Selection, and Rail Issues DOE Office of Nuclear Energy Transportation Planning, Route Selection, and Rail Issues...

345

Analysis and Selection of Analytical Tools to Assess National...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

and Selection of Analytical Tools to Assess National-Interest Transmission Bottlenecks Final Report Analysis and Selection of Analytical Tools to Assess National-Interest...

346

Hydrochemistry of selected parameters at the Raft River KGRA...  

Open Energy Info (EERE)

Hydrochemistry of selected parameters at the Raft River KGRA, Cassia County, Idaho Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Report: Hydrochemistry of selected...

347

Los Alamos National Laboratory selects three small businesses...  

NLE Websites -- All DOE Office Websites (Extended Search)

Three small businesses selected for environmental work Los Alamos National Laboratory selects three small businesses for environmental work The companies chosen are Terranear PMC,...

348

Los Alamos National Laboratory Selects Three Small Businesses...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Los Alamos National Laboratory Selects Three Small Businesses for Environmental Work Los Alamos National Laboratory Selects Three Small Businesses for Environmental Work September...

349

Los Alamos National Laboratory selects three small businesses...  

NLE Websites -- All DOE Office Websites (Extended Search)

LANL selects three small businesses for environmental work Los Alamos National Laboratory selects three small businesses for environmental work The companies chosen are Terranear...

350

NNSA selects Consolidated Nuclear Security, LLC to manage the...  

NLE Websites -- All DOE Office Websites (Extended Search)

selects Consolidated ... NNSA selects Consolidated Nuclear Security, LLC to manage the consolidated contract for Nuclear Production Operations Posted: January 8, 2013 - 1:20pm In a...

351

Solid-State Lighting Recovery Act Award Selections | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Solid-State Lighting Recovery Act Award Selections Solid-State Lighting Recovery Act Award Selections A chart highlighting core technology research projects and product development...

352

Solid-State Lighting: Successful Selection of LED Streetlight...  

NLE Websites -- All DOE Office Websites (Extended Search)

Successful Selection of LED Streetlight Luminaires: Optimizing Illumination and Economic Performance to someone by E-mail Share Solid-State Lighting: Successful Selection of LED...

353

Recovery Act Selections for Smart Grid Investment Grant Awards...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Selections for Smart Grid Investment Grant Awards- By Category Updated July 2010 Recovery Act Selections for Smart Grid Investment Grant Awards- By Category Updated July 2010 A...

354

Recovery Act Selections for Smart Grid Investment Grant Awards...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Category Updated November 2011 Recovery Act Selections for Smart Grid Investment Grant Awards - By Category Updated November 2011 List of selections for the Smart Grid Investment...

355

Recovery Act Selections for Smart Grid Investment Grant Awards...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

State - Updated November 2011 Recovery Act Selections for Smart Grid Investment Grant Awards - By State - Updated November 2011 List of selections for the Smart Grid Investment...

356

The Measurement of the Moisture Concentration of Selected Test...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

The Measurement of the Moisture Concentration of Selected Test Model Ore Zones (April 1977) The Measurement of the Moisture Concentration of Selected Test Model Ore Zones (April...

357

AUDIT OF SELECTED GOVERNMENT-FUNDEDGRANTS AND CONTRACTSAT PRINCETON...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

AUDIT OF SELECTED GOVERNMENT-FUNDEDGRANTS AND CONTRACTSAT PRINCETON UNIVERSITYERS, ER-B-98-04 AUDIT OF SELECTED GOVERNMENT-FUNDEDGRANTS AND CONTRACTSAT PRINCETON UNIVERSITYERS,...

358

Recovery Act Selections for Smart Grid Invesment Grant Awards...  

NLE Websites -- All DOE Office Websites (Extended Search)

Recovery Act Selections for Smart Grid Invesment Grant Awards- By Category Updated July 2010 Recovery Act Selections for Smart Grid Invesment Grant Awards- By Category Updated July...

359

Review of Selected Elements of Emergency Management at the Oak...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

OVERSIGHT REVIEW OF SELECTED ELEMENTS OF EMERGENCY MANAGEMENT AT THE OAK RIDGE NATIONAL LABORATORY July 2011 i INDEPENDENT OVERSIGHT REVIEW OF SELECTED ELEMENTS OF EMERGENCY...

360

Review of Selected Elements of Emergency Management at the Oak...  

NLE Websites -- All DOE Office Websites (Extended Search)

INDEPENDENT OVERSIGHT REVIEW OF SELECTED ELEMENTS OF EMERGENCY MANAGEMENT AT THE OAK RIDGE NATIONAL LABORATORY July 2011 i INDEPENDENT OVERSIGHT REVIEW OF SELECTED ELEMENTS OF...

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Smart Grid Investment Grant (SGIG) Recipient Workshop: From Selection...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Selection to Award, Successfully Navigating the Negotiations Process, November 19, 2009 Smart Grid Investment Grant (SGIG) Recipient Workshop: From Selection to Award,...

362

Pre- and post-selected quantum states: density matrices, tomography, and Kraus operators  

E-Print Network (OSTI)

We present a general formalism for charecterizing 2-time quantum states, describing pre- and post-selected quantum systems. The most general 2-time state is characterized by a `density vector' that is independent of measurements performed between the preparation and post-selection. We provide a method for performing tomography of an unknown 2-time density vector. This procedure, which cannot be implemented by weak or projective measurements, brings new insight to the fundamental role played by Kraus operators in quantum measurements. Finally, after showing that general states and measurements are isomorphic, we show that any measurement on a 2-time state can be mapped to a measurement on a preselected bipartite state.

Ralph Silva; Yelena Guryanova; Nicolas Brunner; Noah Linden; Anthony J. Short; Sandu Popescu

2013-08-09T23:59:59.000Z

363

DATA QUALITY OBJECTIVES FOR SELECTING WASTE SAMPLES FOR THE BENCH STEAM REFORMER TEST  

SciTech Connect

This document describes the data quality objectives to select archived samples located at the 222-S Laboratory for Fluid Bed Steam Reformer testing. The type, quantity and quality of the data required to select the samples for Fluid Bed Steam Reformer testing are discussed. In order to maximize the efficiency and minimize the time to treat Hanford tank waste in the Waste Treatment and Immobilization Plant, additional treatment processes may be required. One of the potential treatment processes is the fluid bed steam reformer (FBSR). A determination of the adequacy of the FBSR process to treat Hanford tank waste is required. The initial step in determining the adequacy of the FBSR process is to select archived waste samples from the 222-S Laboratory that will be used to test the FBSR process. Analyses of the selected samples will be required to confirm the samples meet the testing criteria.

BANNING DL

2010-08-03T23:59:59.000Z

364

Commissioning of the ATLAS Trigger Event Selection with Single?Beam and Cosmic Rays  

E-Print Network (OSTI)

ATLAS is one of the two general?purpose detectors at the Large Hadron Collider (LHC). The trigger system needs to efficiently reject a huge rate of background events and still select potentially interesting ones with good efficiency. After a first processing level using custom electronics, the trigger event selection is made by the High Level Trigger (HLT) system, implemented in software. To reduce the processing time to manageable levels, the HLT uses seeded, step?wise and fast selection algorithms, aiming at the earliest possible rejection of background events. The ATLAS trigger event selection is based on the reconstruction of potentially interesting physical objects like electrons, muons, jets etc. The recent LHC startup and short single?beam run provided the first test of the trigger system against real data. Following this period, ATLAS continued to collect cosmic?ray events for detector alignment and calibration purposes. Both running periods provided very important data to commission the trigg...

Urquijo, P; The ATLAS collaboration

2009-01-01T23:59:59.000Z

365

Electric Time in Quantum Cosmology  

E-Print Network (OSTI)

Effective quantum cosmology is formulated with a realistic global internal time given by the electric vector potential. New possibilities for the quantum behavior of space-time are found, and the high-density regime is shown to be very sensitive to the specific form of state realized.

Stephon Alexander; Martin Bojowald; Antonino Marciano; David Simpson

2012-12-10T23:59:59.000Z

366

Time-Constrained Loop Pipelining  

Science Conference Proceedings (OSTI)

This paper addresses the problem of Time-Constrained Loop Pipelining, i.e. given a fixed throughput, finding a schedule of a loop which minimizes resource requirements. This paper proposes a methodology, called TCLP, based on dividing the problem into ... Keywords: loop pipelining, scheduling, timing and resource contraints, register optimization

Fermin Sanchez

1995-12-01T23:59:59.000Z

367

Beam Time Allocation Committee (BAC)  

NLE Websites -- All DOE Office Websites (Extended Search)

Time Allocation Committee (BAC) Time Allocation Committee (BAC) Charter Purpose: Allocates general user beam time by instrument to promote diverse and high- impact science and a broad-based user community to meet DOE and NSSD goals. Participants: BAC Chair (appointed by NSSD Director), Instrument Group Leaders, User Office Schedule: Tied to proposal calls - expected to meet at least 2 times/year with meetings scheduled about 6 weeks after the proposal call has closed and at least 1 month prior to scheduled operations. Process: 1. Instrument Group Leaders (with group members): a. Confirm feasibility (equipment requirements and instrument capabilities) and safe operations b. Review amount of beam time requested and adjust as needed with consideration for instrument and sample environment availability.

368

Review and selection of unsaturated flow models  

SciTech Connect

Since the 1960`s, ground-water flow models have been used for analysis of water resources problems. In the 1970`s, emphasis began to shift to analysis of waste management problems. This shift in emphasis was largely brought about by site selection activities for geologic repositories for disposal of high-level radioactive wastes. Model development during the 1970`s and well into the 1980`s focused primarily on saturated ground-water flow because geologic repositories in salt, basalt, granite, shale, and tuff were envisioned to be below the water table. Selection of the unsaturated zone at Yucca Mountain, Nevada, for potential disposal of waste began to shift model development toward unsaturated flow models. Under the US Department of Energy (DOE), the Civilian Radioactive Waste Management System Management and Operating Contractor (CRWMS M&O) has the responsibility to review, evaluate, and document existing computer models; to conduct performance assessments; and to develop performance assessment models, where necessary. This document describes the CRWMS M&O approach to model review and evaluation (Chapter 2), and the requirements for unsaturated flow models which are the bases for selection from among the current models (Chapter 3). Chapter 4 identifies existing models, and their characteristics. Through a detailed examination of characteristics, Chapter 5 presents the selection of models for testing. Chapter 6 discusses the testing and verification of selected models. Chapters 7 and 8 give conclusions and make recommendations, respectively. Chapter 9 records the major references for each of the models reviewed. Appendix A, a collection of technical reviews for each model, contains a more complete list of references. Finally, Appendix B characterizes the problems used for model testing.

Reeves, M.; Baker, N.A.; Duguid, J.O. [INTERA, Inc., Las Vegas, NV (United States)

1994-04-04T23:59:59.000Z

369

Finding patterns in timed data with spike timing dependent plasticity  

E-Print Network (OSTI)

My research focuses on finding patterns in events - in sequences of data that happen over time. It takes inspiration from a neuroscience phenomena believed to be deeply involved in learning. I propose a machine learning ...

Oliveira, Alexandre (Alexandre S.)

2012-01-01T23:59:59.000Z

370

Criteria for Selection of Seed Motions to Envelop Design Response Spectra  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Selection of Seed Selection of Seed Motions to Envelop Design Response Spectra DOE Natural Phenomena Hazards Workshop October 25, 2011 Michael Costantino, Thomas Houston, Greg Mertz, Andrew Maham CJCAssociates Introduction * Recently, CJC&A has performed several studies regarding seed record selection used in the development of acceleration time histories for input into seismic analyses. - Primary issue - how does the seed record affect computed structural response. * This presentation is the result of two publications, as well as insights developed from the following DOE projects: - SSI analysis of the Uranium Processing Facility (Y12) - Probabilistic SSI analysis of PF4 (LANL) - Preliminary SSI analysis of CMRR (LANL) 2 CJCAssociates Background * Current design procedures used to develop synthetic time histories for the

371

Selection of 3013 Containers for Field Surveillance  

SciTech Connect

This report revises and combines three earlier reports dealing with the binning, statistical sampling, and sample selection of 3013 containers for field surveillance. It includes changes to the binning specification resulting from completion of the Savannah River Site packaging campaign and new information from the shelf-life program and field surveillance activities. The revised bin assignments result in changes to the random sample specification. These changes are necessary to meet the statistical requirements of the surveillance program. This report will be reviewed regularly and revised as needed. Section 1 of this report summarizes the results of an extensive effort to assign all of the current and projected 3013 containers in the Department of Energy (DOE) inventory to one of three bins (Innocuous, Pressure and Corrosion, or Pressure) based on potential failure mechanisms. Grouping containers into bins provides a framework to make a statistical selection of individual containers from the entire population for destructive and nondestructive field surveillance. The binning process consisted of three main steps. First, the packaged containers were binned using information in the Integrated Surveillance Program database and a decision tree. The second task was to assign those containers that could not be binned using the decision tree to a specific bin using container-by-container engineering review. The final task was to evaluate containers not yet packaged and assign them to bins using process knowledge. The technical basis for the decisions made during the binning process is included in Section 1. A composite decision tree and a summary table show all of the containers projected to be in the DOE inventory at the conclusion of packaging at all sites. Decision trees that provide an overview of the binning process and logic are included for each site. Section 2 of this report describes the approach to the statistical selection of containers for surveillance and consists of a revision of the earlier statistical sampling report. The requirement of 99.9% probability of observing at least one of the worst 5% (99.9/5%) of the containers with a potential for degradation is used to determine the number of containers in the random sample for the Pressure and Corrosion and the Pressure bins. Sampling requirements for the Innocuous bin are not based on the 99.9/5% requirement; rather, they are based on evaluating the assumption of no significant degradation of, or variability between, containers relative to corrosion or pressure generation within the Innocuous bin population as valid. Section 3 of this report focuses on the actual selection of 3013 containers for surveillance. Surveillance containers are identified by the year that the surveillance should be performed. In addition to the randomly selected containers, containers were selected from the entire population, based on engineering judgment for each of these years. The judgmental sampling targets containers with the greatest potential for gas generation and/or corrosion. The factors used for judgmental sample selection are documented in this section. A more detailed discussion of the FY 2005 sample selection process is contained in the previous FY 2005 sample selection report.

Larry Peppers, Elizabeth Kelly, James McClard, Gary Friday, Theodore Venetz, and Jerry Stakebade

2007-01-01T23:59:59.000Z

372

Selective ensemble extreme learning machine modeling of effluent quality in wastewater treatment plants  

Science Conference Proceedings (OSTI)

Real-time and reliable measurements of the effluent quality are essential to improve operating efficiency and reduce energy consumption for the wastewater treatment process. Due to the low accuracy and unstable performance of the traditional effluent ... Keywords: Wastewater treatment process, effluent quality prediction, extreme learning machine, genetic algorithm, selective ensemble model

Li-Jie Zhao; Tian-You Chai; De-Cheng Yuan

2012-12-01T23:59:59.000Z

373

Selections: internet voting with over-the-shoulder coercion-resistance  

Science Conference Proceedings (OSTI)

We present Selections, a new cryptographic voting protocol that is end-to-end verifiable and suitable for Internet voting. After a one-time in-person registration, voters can cast ballots in an arbitrary number of elections. We say a system provides ...

Jeremy Clark; Urs Hengartner

2011-02-01T23:59:59.000Z

374

QoS-Driven web services selection in autonomic grid environments  

Science Conference Proceedings (OSTI)

In the Service Oriented Architecture (SOA) complex applications can be described as business processes from independently developed services that can be selected at run time on the basis of the provided Quality of Service (QoS) However, QoS requirements ...

Danilo Ardagna; Gabriele Giunta; Nunzio Ingraffia; Raffaela Mirandola; Barbara Pernici

2006-10-01T23:59:59.000Z

375

Charging station selection optimization for plug-in electric vehicles: An oligopolistic game-theoretic framework  

Science Conference Proceedings (OSTI)

In this paper, we describe a framework for the selection of the best charging station when plug-in electric vehicles (PEV) need to recharge their batteries, while at the same time the power utilities, which own the charging stations (CS), optimize their ...

J. Joaquin Escudero-Garzas; Gonzalo Seco-Granados

2012-01-01T23:59:59.000Z

376

Selection of power plant elements for future space electric power systems  

SciTech Connect

A study on the type of nuclear reactor power plants that should be developed for future space missions is described. After careful consideration of power plant configuration weights, sizes, reliabilities, safety, development cost and time, the configuration selected to be pursued was a heat-pipe reactor design with thermoelectric converters and heat-pipe radiator.

Buden, D.

1979-01-01T23:59:59.000Z

377

EVALUATION AND SELECTION OF 99TC GETTERS FOR SEQUESTRATION OF LIQUID SECONDARY WASTE RESULTING FROM VITRIFICATION OF RADIOACTIVE WASTE FROM HANFORD  

Science Conference Proceedings (OSTI)

Getters are most commonly inorganic materials that selectively adsorb radionuclide and metallic contaminants. Typically, these materials have been deployed in two different modes to immobilize and retard contaminant release from monolithic waste forms. One mode is to first use getters to selectively scavenge the radionuclide of interest from a liquid waste stream, and then incorporate the radionuclide-loaded getters in cementitious or other monolithic waste forms. The other mode consists of mixing getters and liquid waste together during formulation of monolithic waste forms. Desirable characteristics for a getter material include, (1) specific adsorption of radionuclide of interest and very high selectivity toward radionuclides of concern in concentrations that would be several orders of magnitude less than the concentrations of competing anions and cations, (2) adsorption capacity that should be sufficient for the mass and volume of the material that will be deployed to be within practicable limits, (3) long-term adsorption and retention of radionuclide, (4) sufficient physical and chemical stability that its radionuclide retention performance will not degrade significantly during the designed life span of the waste form, (5) chemical stability under the range of Eh, pH, and solution conditions that exist in the waste form environment, and (6) should not adversely affect chemical and physical integrity of waste forms. We conducted a literature review to identify getters that are suitable for effectively sequestering 99Tc in monolithic waste forms that are being evaluated for stabilizing secondary liquid waste streams resulting from treatment and vitrification of radioactive tank wastes at Hanford. As a result of this review, we identified a set of getters that warrant further evaluation for this specific application.

Mattigod, Shas V.; Westsik, Joseph H.

2011-03-31T23:59:59.000Z

378

Upgrade of NSLS timing system  

SciTech Connect

We report on the progress of the new NSLS timing system. There are three types of requirements for NSLS timing system: clocks, synchronization and trigger circuits. All ring revolution frequency clocks are generated using ECL and high speed TTL logic. The synchronization circuits allows to fill both storage rings with any bunch pattern. The triggers are generated by using commercially available digital delay generators. The delay unit`s outputs are ultrastable, with a resolution of 5 ps, and are programmed by computer via IEEE 488 interface. The block diagrams, description of all major timing components and the present status are provided in this paper.

Singh, O.; Ramamoorthy, S.; Sheehan, J.; Smith, J.

1995-05-01T23:59:59.000Z

379

MCS Division researchers awarded INCITE supercomputing time | Argonne  

NLE Websites -- All DOE Office Websites (Extended Search)

awarded INCITE supercomputing time awarded INCITE supercomputing time November 21, 2013 Tweet EmailPrint Three researchers in the Mathematics and Computer Science Division at Argonne lead projects that have been awarded a total of 285 million hours of computing time on the U.S. Department of Energy (DOE) leadership-class computing facilities. Using the computer allotments, the researchers will conduct advanced simulation and analysis and will develop scalable system software needed to fully utilize the power of leadership-class computing facilities. The projects, selected competitively based on their potential to advance scientific discovery, were awarded the supercomputer time through the DOE Innovative and Novel Computational Impact on Theory and Experiment (INCITE) program. Salman Habib, a senior physicist and computational scientist and member of

380

Fragment-based Time-dependent Density-functional Theory  

E-Print Network (OSTI)

Using the Runge-Gross theorem that establishes the foundation of Time-dependent Density Functional Theory (TDDFT) we prove that for a given electronic Hamiltonian, choice of initial state, and choice of fragmentation, there is a unique single-particle potential (dubbed time-dependent partition potential) which, when added to each of the pre-selected fragment potentials, forces the fragment densities to evolve in such a way that their sum equals the exact molecular density at all times. This uniqueness theorem suggests new ways of computing time-dependent properties of electronic systems via fragment-TDDFT calculations. We derive a formally exact relationship between the partition potential and the total density, and illustrate our approach on a simple model system for binary fragmentation in a laser field.

Mosquera, Martin A; Wasserman, Adam

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Timing matters: Lessons From The CA Literature On Updating  

E-Print Network (OSTI)

In the present article we emphasize the importance of modeling time in the context of agent-based models. To this end, we present a (selective) survey of the Cellular Automata-literature on updating and draw parallels to the issue of agent activation in agent-based models. By means of two simple models, Schelling's segregation model and Epstein's demographic prisoner's dilemma we investigate the influence of choosing different regimes of agent activation. Our experiments indicate that timing is not a critical issue for very simple models but bears huge influence on model behavior and results as soon as the degree of complexity increases only so slightly. After a brief review of the way commonly used ABM simulation environments handle the issue of timing, we draw some tentative conclusions about the importance of timing and the need for more research towards that direction, similar to the concerted effort on updating in cellular automata.

Radax, Wolfgang

2010-01-01T23:59:59.000Z

382

Silicon photomultiplier timing performance study  

E-Print Network (OSTI)

Many characteristics of Silicon Photomultipliers can be tuned with temperature and operation voltage. We present preliminary results of a study of the effect of these two operation parameters on the time resolution of large active area Multi-Pixel Photon Counters (MPPCs) manufactured by Hamamatsu. Measurements at -10 C, 0 C, and 10 C at different bias voltages were performed. The time resolution is best at low temperature and high over-voltage. Most significant improvements can be achieved in cases with low number of fired pixels (40 pixels) the effect of temperature and operation voltage becomes smaller. The timing performance still improves with decreasing temperature (~ factor of 2) but it hardly depends on the operation voltage. The study shows, that especially in applications where only few photons are available for detection a careful optimization of temperature and operation voltage are advisable to obtain optimum timing results with the MPPC.

Gama Ahmed; Paul Bühler; Johann Marton; Ken Suzuki

2010-06-21T23:59:59.000Z

383

Logarithmic time parallel Bayesian inference  

Science Conference Proceedings (OSTI)

I present a parallel algorithm for exact probabilistic inference in Bayesian networks. For polytree networks with n variables, the worstcase time complexity is O(logn) on a CREW PRAM (concurrent-read, exclusive-write parallel random-access ...

David M. Pennock

1998-07-01T23:59:59.000Z

384

The structure of cosmic time  

E-Print Network (OSTI)

Following the approach of Julien Lesgourgues [1], we analyze the mathematical structure of the time co-ordinate of present day cosmological models, where these models include a cosmological constant term to account for the observed acceleration of the universe [2], [3]: we find that in all cases, except for a set of measure zero in the parameter space, the time is given by an (abelian) integral on a torus; the imaginary period of this integral then gives a natural periodicity in imaginary time for the universe; following Stephen Hawking [4], [5], this periodicity may be interpreted either as giving a fundamental mass scale for the universe, or (using Planck’s constant) a fundamental temperature, or both. The precise structure that emerges suggests that the structure of time can be regarded as an order parameter arising perhaps in a phase transition in the early universe; one might hope that this structure

George Sparling

2006-01-01T23:59:59.000Z

385

A real time priority scheduler  

Science Conference Proceedings (OSTI)

The real time priority scheduler reported herein evolved from a design effort to provide software aids for handling the interrupts that occur in hybrid computation. Since these interrupts are both internal and external (i.e., generated internal and external ...

Karl Ramsay; Jon C. Strauss

1966-01-01T23:59:59.000Z

386

Time-Constrained Loop Pipelining  

E-Print Network (OSTI)

This paper addresses the problem of Time-Constrained Loop Pipelining, i.e. given a fixed throughput, finding a schedule of a loop which minimizes resource requirements. We propose a methodology, called TCLP, based on dividing the problem into two simpler and independent tasks: retiming and scheduling. TCLP explores different sets of resources, searchingfor a maximum resource utilization. This reduces area requirements. After a minimum set of resourceshas been found, the execution throughput is increased and the number of registers required by the loop schedule is reduced. TCLP attempts to generate a schedule which minimizes cost in time and area (resources and registers). The results show that TCLP obtains optimal schedules in most cases. 1 Introduction This paper presents TCLP, a methodology to solve TimeConstrained Loop Pipelining. TCLP is NP-complete [3]. Two types of timing constraints (TCs) have been considered in the literature: local TCs to specify minimum and/or maximum TCs ...

Fermn Sanchez; Jordi Cortadella

1995-01-01T23:59:59.000Z

387

No Evidence of Time Dilation in Gamma-Ray Burst Data  

E-Print Network (OSTI)

Gamma-Ray Bursts have been observed out to very high redshifts and provide time measures that are directly related to intrinsic time scales of the burst. Einstein's theory of relativity is quite definite that if the universe is expanding then the observed duration of these measures will increase with redshift. Thus gamma-ray burst measures should show a time dilation proportional to redshift. An analysis of gamma-ray burst data shows that the hypothesis of time dilation is rejected with a probability of 4.4$\\times10^{-6}$ for redshifts out to z=6.6. Traditionally the lack of an apparent time dilation has been explained by an inverse correlation between luminosity and time measures together with strong luminosity selection as a function of redshift. It is shown that the inverse correlation between luminosity and some time measures is confirmed, but using concordance cosmology strong luminosity selection cannot be achieved. It may be possible to explain the apparent lack of time dilation with a combination of gamma-ray burst selection, some luminosity evolution and some time measure evolution. But this requires a remarkable coincidence in order to produce the apparent lack of time dilation. However the data are consistent with a static cosmology in a non-expanding universe.

David F. Crawford

2009-01-27T23:59:59.000Z

388

Discrete space-time symmetries  

SciTech Connect

Symmetries have always fascinated human beings; they are found in nature, art, and architecture. Physicists, like other scientists have often used symmetries as a basis of their understanding of nature. When the dynamics is unknown, symmetries serve to delineate and define it. When the dynamics is known, symmetries are used to study structure. These two lectures review the theory and present understanding and status of two discrete space-time symmetries,, namely parity (P) and time reversal (T).

Henley, E.M.

1992-12-31T23:59:59.000Z

389

Discrete space-time symmetries  

SciTech Connect

Symmetries have always fascinated human beings; they are found in nature, art, and architecture. Physicists, like other scientists have often used symmetries as a basis of their understanding of nature. When the dynamics is unknown, symmetries serve to delineate and define it. When the dynamics is known, symmetries are used to study structure. These two lectures review the theory and present understanding and status of two discrete space-time symmetries,, namely parity (P) and time reversal (T).

Henley, E.M.

1992-01-01T23:59:59.000Z

390

NETL: Hydrogen Selective Exfoliated Zeolite Membranes  

NLE Websites -- All DOE Office Websites (Extended Search)

Hydrogen Selective Exfoliated Zeolite Membranes Hydrogen Selective Exfoliated Zeolite Membranes Project No.: DE-FE0001322 The University of Minnesota is developing a technically and economically viable membrane for carbon dioxide (CO2) separation from typical water-gas-shift (WGS) mixture feeds. The goal of this project is to further develop recently developed membrane technology based on exfoliated zeolite coatings as components for carbon capture in integrated gasification combined cycle plants. These membranes have the potential to contribute to carbon capture by high-temperature separation of hydrogen from CO2 and other gases present in shifted synthesis gas. Molecular sieve membrane for the pre-combustion capture of CO2. Molecular sieve membrane for the pre-combustion capture of CO2. Related Papers and Publications:

391

Fluidized bed selective pyrolysis of coal  

DOE Patents (OSTI)

The present invention discloses a process for the pyrolysis of coal which comprises the effective utilization of two zonal inclined fluidized beds, where said zones can be selectively controlled as to temperature and heating rate. The first zonal inclined fluidized bed serves as a dryer for crushed coal and additionally is controlled to selectively pyrolyze said coal producing substantially carbon dioxide for recycle use. The second zonal inclined fluidized bed further pyrolyses the coal to gaseous, liquid and char products under controlled temperature and heating rate zones designed to economically integrate the product mix. The gas and liquid products are recovered from the gaseous effluent stream while the char which remains can be further treated or utilized in a subsequent process step. 9 figs.

Shang, J.Y.; Cha, C.Y.; Merriam, N.W.

1992-12-15T23:59:59.000Z

392

Fluidized bed selective pyrolysis of coal  

SciTech Connect

The present invention discloses a process for the pyrolysis of coal which comprises the effective utilization of two zonal inclined fluidized beds, where said zones can be selectively controlled as to temperature and heating rate. The first zonal inclined fluidized bed serves as a dryer for crushed coal and additionally is controlled to selectively pyrolyze said coal producing substantially carbon dioxide for recycle use. The second zonal inclined fluidized bed further pyrolyzes the coal to gaseous, liquid and char products under controlled temperature and heating rate zones designed to economically integrate the product mix. The gas and liquid products are recovered from the gaseous effluent stream while the char which remains can be further treated or utilized in a subsequent process step.

Shang, Jer Y. (McLean, VA); Cha, Chang Y. (Golden, CO); Merriam, Norman W. (Laramie, WY)

1992-01-01T23:59:59.000Z

393

Meteorology: typical meteorological year data for selected stations in Sri  

Open Energy Info (EERE)

Sri Sri Lanka from NREL Dataset Summary Description (Abstract): A data set of hourly values of solar radiation and meteorological elements for a 1-year period. (Purpose): Simulations (Supplemental Information): A TMY consists of months selected from individual years and concatenated to form a complete year. The intended use is for computer simulations of solar energy conversion systems and building systems. Because of the selection criteria, these TMYs are not appropriate for simulations of wind energy conversion systems. A TMY provides a standard for hourly data for solar radiation and other meteorological elements that permit performance comparisons of system types and configurations for one or more locations. A TMY is not necessarily a good indicator of conditions over the next year, or even the next 5 years. Rather, it represents conditions judged to be typical over a long period of time, such as 30 years. Because they represent typical rather than extreme conditions, they are not suited for designing systems and their components to meet the worst-case conditions occurring at a location.

394

Selectivity Estimation for Spatio-Temporal Queries to Moving Objects  

E-Print Network (OSTI)

omni@islab.kaist.ac.kr chungcw@cs.kaist.ac.kr Divisionof ComputerScience Department of Electrical of selection queries: one for historical positions of moving objects and the other for future positions the selection query efficiently, an accu- rate estimation of the selectivity is required. The selectivity

Chung, Chin-Wan

395

Customized BGP Route Selection Using BGP/MPLS VPNs  

E-Print Network (OSTI)

Customized route selection mechanisms at ASBR Use Virtual Routing and Forwarding (VRF) instances to build

Bonaventure, Olivier

396

Effective Tag Set Selection in Chinese Word Segmentation  

E-Print Network (OSTI)

Effective Tag Set Selection in Chinese Word Segmentation via Conditional Random Field Modeling Hai that we consider both feature template selection and tag set selection, instead of feature template as different tag sets are selected. Based on the proposed method, our system gives the state

397

A mutation-selection model with recombination for general genotypes  

E-Print Network (OSTI)

A mutation-selection model with recombination for general genotypes Steven N. Evans David II: Polynomial selective costs 9 1.4. Example III: Demographic selective costs 10 1.5. Comments selective cost 23 3.3. Fr´echet derivatives 26 3.4. Existence of equilibria via perturbation 27 3.5. Concave

Evans, Steven N.

398

Selecting and Evaluating Indicators for the California Current  

E-Print Network (OSTI)

Selecting and Evaluating Indicators for the California Current Selecting Ecosystem Indicators Goals Will Determine the Suite of Indicators It is a significant challenge to select a suite-lived, slow growing fish with a K-selected life history (MacArthur and Wilson 1967, Moyle 2002). Mature

399

NEUP Project Selections_September212011_IRP and Infrastructure Improvements  

Energy.gov (U.S. Department of Energy (DOE))

Projects selections for NEUP 2011 under Integrated Research Projects and University Research Infrastructure Improvements.

400

Database - Selective Catalytic Reduction Catalyst Deactivation Rates  

Science Conference Proceedings (OSTI)

Selective catalytic reduction (SCR) catalyst deactivation is a critical parameter controlling to a large extent achievable catalyst life, as well as overall SCR system performance. Accurate assessment and prediction of catalyst deactivation is required to adequately manage reactor potential. EPRI has on-going efforts underway aimed at better understanding the factors that affect catalyst deactivation, especially as a function of fuel, boiler design, and boiler operating conditions, in hopes of ...

2013-11-06T23:59:59.000Z

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Interfacial phenomena on selected cathode materials  

DOE Green Energy (OSTI)

We have carried out a series of surface studies of selected cathode materials. Instrumental techniques such as Raman microscopy, surface enhanced Raman spectroscopy (SERS), and atomic force microscopy were used to investigate the cathode surfaces. The goal of this study was to identify detrimental processes which occur at the electrode/electrolyte interface and can lead to electrode degradation and failure during cycling and/or storage at elevated temperatures.

Kostecki, Robert; Matsuo, Yoshiaki; McLarnon, Frank

2001-06-22T23:59:59.000Z

402

Selected papers for global `95 concerning plutonium  

SciTech Connect

This report contains selected papers from the Global `95 Conference ``Evaluation of Emerging Nuclear Fuel Cycle Systems,`` held in Versailles, Sept. 11-14, 1995. The 11 papers in Part I are from ``Benefits and Risks of Reprocessing`` sessions. The 7 papers in Part II are some of the more interesting poster papers that relate to the use of Pu for power generation. Finally, the 3 papers are on the topic of management and disposition of Pu from retired nuclear weapons.

Sutcliffe, W.G. [ed.

1996-06-14T23:59:59.000Z

403

Guiding Architects in Selecting Architectural Evolution Alternatives  

SciTech Connect

Although there exist methods and tools to support architecture evolution, the derivation and evaluation of alternative evolution paths are realized manually. In this paper, we introduce an approach, where architecture specification is converted to a graph representation. Based on this representation, we automatically generate possible evolution paths, evalute quality attributes for different architecture configurations, and optimize the selection of a particular path accordingly. We illustrate our approach by modeling the software architecture evolution of a crisis management system.

Ciraci, Selim; Sozer, Hasan; Aksit, Mehmet

2011-09-09T23:59:59.000Z

404

The Lake Baikal neutrino experiment: selected results  

E-Print Network (OSTI)

We review the present status of the lake Baikal Neutrino Experiment and present selected physical results gained with the consequetive stages of the stepwise increasing detector: from NT-36 to NT-96. Results cover atmospheric muons, neutrino events, very high energy neutrinos, search for neutrino events from WIMP annihilation, search for magnetic monopoles and environmental studies. We also describe an air Cherenkov array developed for the study of angular resolution of NT-200.

BAIKAL Collaboration; V. Balkanov

2000-01-10T23:59:59.000Z

405

2006 Workshop on Selective Catalytic Reduction  

Science Conference Proceedings (OSTI)

EPRI held the 2006 Workshop on Selective Catalytic Reduction (SCR) on October 31 November 2, 2006 at the Dearborn Inn in Dearborn, Michigan and at DTE Energy's Monroe Station. Post-Combustion NOX Control Program members, invited speakers, and EPRI staff participated in this two and a half day event. The workshop agenda was comprised of twenty-seven presentations, two panel discussions, and a plant tour. Operating experience reports on SCR systems at Baldwin, Bowen, Bull Run, Crist, Cumberland, Gaston, Go...

2007-03-07T23:59:59.000Z

406

http://ukpmc.ac.uk select `Submit  

E-Print Network (OSTI)

NCBI Bibliography'. #12;run a search for your articles on PubMed ­ either by entering your own terms or by using a suggested search 5 `Add from PubMed' tab This tab enables you to run a search on PubMed ­ either by using the free-text search box, or by choosing a suggested search ­ to find your publications. #12;select `Add

Newcastle upon Tyne, University of

407

Approximate k-NN delta test minimization method using genetic algorithms: Application to time series  

Science Conference Proceedings (OSTI)

In many real world problems, the existence of irrelevant input variables (features) hinders the predictive quality of the models used to estimate the output variables. In particular, time series prediction often involves building large regressors of ... Keywords: Approximate k-nearest neighbors, Delta test, Genetic algorithm, Time series, Variable projection, Variable scaling, Variable selection

Fernando Mateo; Dušan Sovilj; Rafael Gadea

2010-06-01T23:59:59.000Z

408

Discovery of temporal variation of arsenic in a historical blackfoot disease territory by time series analysis  

Science Conference Proceedings (OSTI)

Time series analysis is useful tool for extracting interesting pattern from ordered sequence of observations. The Chianan Blackfoot disease region was selected as study area, and the monitoring data of arsenic in groundwater during the period of 2003 ... Keywords: arsenic, data mining, groundwater management, time series analysis, water quality

Jan-Yee Lee; Ting-Nien Wu

2009-08-01T23:59:59.000Z

409

Discovery of Temporal Variation of Arsenic in a Historical Blackfoot Disease Territory by Time Series Analysis  

Science Conference Proceedings (OSTI)

Time series analysis is useful tool for extracting interesting pattern from ordered sequence of observations. The Chianan Blackfoot disease region was selected as study area, and the monitoring data of arsenic in groundwater during the period of 2003 ... Keywords: groundwater management, data mining, time series analysis, arsenic, water quality

Jan-Yee Lee; Ting-Nien Wu

2009-08-01T23:59:59.000Z

410

FINAL Combined SGIG Selections - By State for Press -5.xls  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

d d RECOVERY ACT SELECTIONS FOR SMART GRID INVESTMENT GRANT AWARDS - BY STATE HQ State HQ City Name of Awardee Brief Project Description Recovery Act Funding Total Project Value Including Cost Share Map of Project Coverage Area AL Birmingham Southern Company Services, Inc. Deploy five integrated smart grid techology systems that enhance energy efficiency, cyber security, distribution an transmission line automation, and smart power substations that will reduce energy load and save money for consumers. Will also benefit customers in FL, GA, MS, NC and SC. $164,527,160 $330,130,432 Coverage Map Alabama Total $164,527,160 $330,130,432 AR Forrest City Woodruff Electric Install smart meters for more than 13,000 electric cooperative customers that will provide time-of-use data,

411

DOE Selects Contractor for Depleted Hexafluoride Conversion Project Support  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Contractor for Depleted Hexafluoride Conversion Project Contractor for Depleted Hexafluoride Conversion Project Support DOE Selects Contractor for Depleted Hexafluoride Conversion Project Support March 25, 2013 - 12:00pm Addthis Media Contact Bill Taylor, 803-952-8564 Bill.Taylor@srs.gov Cincinnati - The U.S. Department of Energy (DOE) today awarded a competitive small business task order to Navarro Research and Engineering Inc. of Oak Ridge, Tennessee. The award is a $22 million, time and materials task order with a three-year performance period and two one-year extension options. Navarro Research and Engineering Inc. will provide engineering and operations technical support services to the DOE Portsmouth Paducah Project Office (PPPO) in Lexington, Kentucky and the Depleted Uranium Hexafluoride (DUF6) Conversion Project in Paducah, Kentucky and Portsmouth, Ohio.

412

Software evaluation and selection: an evaluation and selection methodology for discrete-event simulation software  

Science Conference Proceedings (OSTI)

For large international companies with their own simulation team it is often hard to select new discrete event simulation software. Often, preferences and application areas between countries differ, and simulation software already in use influences the ...

Tamrat W. Tewoldeberhan; Alexander Verbraeck; Edwin Valentin; Gilles Bardonnet

2002-12-01T23:59:59.000Z

413

" Energy Sources by Industry Group, Selected Industries, and Selected"  

U.S. Energy Information Administration (EIA) Indexed Site

5. Capability to Switch from Distillate Fuel Oil to Alternative" 5. Capability to Switch from Distillate Fuel Oil to Alternative" " Energy Sources by Industry Group, Selected Industries, and Selected" " Characteristics, 1991" " (Estimates in Thousand Barrels)" ,," Distillate Fuel Oil ",,," Alternative Types of Energy(b)" ,,"-","-","-------------","-","-","-","-","-","-","-","RSE" ,,"Total"," ","Not","Electricity","Natural","Residual",,,"Coal Coke",,"Row" ,,"Consumed(c)","Switchable","Switchable","Receipts(d)","Gas","Fuel Oil","Coal","LPG","and Breeze","Other(e)","Factors"

414

" Sources by Industry Group, Selected Industries, and Selected Characteristics,"  

U.S. Energy Information Administration (EIA) Indexed Site

3. Capability to Switch from Electricity to Alternative Energy" 3. Capability to Switch from Electricity to Alternative Energy" " Sources by Industry Group, Selected Industries, and Selected Characteristics," 1991 " (Estimates in Million Kilowatthours)" ,," Electricity Receipts",,," Alternative Types of Energy(b)" ,,"-","-","-----------","-","-","-","-","-","-","-" ,,,,,,,,,,"Coal",,"RSE" ,,"Total"," ","Not","Natural","Distillate","Residual",,,"Coke and",,"Row" ,,"Receipts(c)","Switchable","Switchable","Gas","Fuel Oil","Fuel Oil","Coal","LPG","Breeze","Other(d)","Factors"," "

415

" Sources by Industry Group, Selected Industries, and Selected Characteristics,"  

U.S. Energy Information Administration (EIA) Indexed Site

6. Capability to Switch from Residual Fuel Oil to Alternative Energy" 6. Capability to Switch from Residual Fuel Oil to Alternative Energy" " Sources by Industry Group, Selected Industries, and Selected Characteristics," 1991 " (Estimates in Thousand Barrels)" ,," Residual Fuel Oil",,," Alternative Types of Energy(b)" ," ","-","-","-------------","-","-","-","-","-","-","-","RSE" ,,"Total",,"Not","Electricity","Natural","Distillate",,,"Coal Coke",,"Row" ,,"Consumed(c)","Switchable","Switchable","Receipts(d)","Gas","Fuel Oil","Coal","LPG","and Breeze","Other(e)","Factors"

416

" Sources by Industry Group, Selected Industries, and Selected Characteristics,"  

U.S. Energy Information Administration (EIA) Indexed Site

4. Capability to Switch from Natural Gas to Alternative Energy" 4. Capability to Switch from Natural Gas to Alternative Energy" " Sources by Industry Group, Selected Industries, and Selected Characteristics," 1991 " (Estimates in Billion Cubic Feet)" ,," Natural Gas",,," Alternative Types of Energy(b)" ,,"-","-","-------------","-","-","-","-","-","-","-","RSE" ,,"Total"," ","Not","Electricity","Distillate","Residual",,,"Coal Coke",,"Row" ,,"Consumed(c)","Switchable","Switchable","Receipts(d)","Fuel Oil","Fuel Oil","Coal","LPG","and Breeze","Other(e)","Factors"

417

Selection of actinide chemical analogues for WIPP tests  

Science Conference Proceedings (OSTI)

The Department of Energy must demonstrate the effectiveness of the Waste Isolation Pilot Plant (WIPP) as a permanent repository for the disposal of transuranic (TRU) waste. Performance assessments of the WIPP require that estimates of the transportability and outcome of the radionuclides (actinides) be determined from disposal rooms that may become either partially or completely filled with brine. Federal regulations limit the amount of radioactivity that may be unintentionally released to the accessible environment by any mechanism during the post closure phase up to 10,000 years. Thermodynamic models have been developed to predict the concentrations of actinides in the WIPP disposal rooms under various situations and chemical conditions. These models are based on empirical and theoretical projections of the chemistry that might be present in and around the disposal room zone for both near and long-term periods. The actinides that are known to be present in the TRU wastes (and are included in the model) are Th, U, Np, Pu, and Am. Knowledge of the chemistry that might occur in the disposal rooms when the waste comes in contact with brine is important in understanding the range of oxidation states that might be present under different conditions. There is a need to establish the mechanisms and resultant rate of transport, migration, or effective retardation of actinides beyond the disposal rooms to the boundary of the accessible environment. The influence of the bulk salt rock, clay sediments and other geologic matrices on the transport behavior of actinides must be determined to establish the overall performance and capability of the WIPP in isolating waste from the environment. Tests to determine the capabilities of the WIPP geologic formations in retarding actinide species in several projected oxidation states would provide a means to demonstrate the effectiveness of the WIPP in retaining TRU wastes.

Villarreal, R.; Spall, D.

1995-07-05T23:59:59.000Z

418

Tough Times for the Muskrats  

NLE Websites -- All DOE Office Websites (Extended Search)

Tough Times for the Muskrats Tough Times for the Muskrats Nature Bulletin No. 3 February 24, 1945 Forest Preserve District of Cook County Clayton F Smith, President Roberts Mann, Superintendent of Conservation TOUGH TIMES FOR THE MUSKRATS This has been a sorry year for the muskrats. The long drought, last summer and fall, dried up many of the smaller marshes and ponds where they had been living and forced them to migrate overland to new homes. Many undoubtedly were killed while enroute by mink, hawks, or dogs. Even the larger marshes and ponds were made smaller and more shallow by the drought and now this severe winter, with its long, bitter cold, has caused many of them to freeze solid to the very bottom; thus sealing the muskrats up in their lodges and preventing them from swimming around under the ice to get food.

419

May 2008 Y-12 Times  

NLE Websites -- All DOE Office Websites (Extended Search)

5 5 May 2008 www.y12.doe.gov/news/times.php P.O. Box 2009 Oak Ridge, TN 37831-8245 Managing Editor Melissa Leinart 865-574-1621 (6ml) Associate Editors Amy Alley Heidi Spurling Layout/Design Lisa Harris Contributors Ellen Boatner Ken Davis Kathy Fahey Stuart Hames Sharon McConathy Patrick McCoy I N S I D E Page 3 Fire department members come to the rescue Page 4 Driving green to protect our natural resources Page 5 73s: Best regards from Y-12's hams Page8 What's the secret? Mary Murray Brett Pate Ray Smith Donna Watson Bill Wilburn Lisa Xiques times times the B&W Technical Services Y-12, LLC, a partnership between Babcock & Wilcox Technical Services Group Inc. and Bechtel National Inc., operates the Y-12 National Security Complex. When you see information regarding the recent Voluntary Separation Payment

420

Dielectric Analog Space-Times  

E-Print Network (OSTI)

We generalize the notion of a dielectric analog Schwarzschild black hole model to analog models of arbitrary space-times; in particular, the approach is not restricted to static space-times. This is done by establishing a correspondence between electrodynamics on a curved, vacuum manifold, with electrodynamics in a general linear dielectric residing in Minkowski space-time. The mapping is not unique, allowing for some freedom in the specification of equivalent materials, which could be useful for exploiting recent developments in the production of metamaterials. Some examples are considered, with special attention paid to the dielectric analog of the exterior Kerr geometry, which is found to be reproducible with regular, linear, dielectrics.

Robert T. Thompson; Jörg Frauendiener

2010-10-08T23:59:59.000Z

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Time-Off Awards Scale  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

/1/2010 /1/2010 TIME OFF AWARD SCALE The following chart is recommended and should be used unless another time-off award scale has been adopted by the servicing human resources office. TIME OFF SCALE VALUE OF THE EMPLOYEE'S CONTRIBUTION HOURS TO BE AWARDED MODERATE - A contribution to a product, program or service to the public which is of sufficient value to merit formal recognition. Beneficial change or modification of operating principles or procedures. 1 - 10 Hours SUBSTANTIAL - An important contribution to the value of a product, activity, program or service to the public. Significant change or modification or operating principles or procedures. 11 - 20 Hours HIGH - A significant contribution to the value of a product, activity, program or service to

422

PRECISION TIME-DELAY CIRCUIT  

DOE Patents (OSTI)

A tine-delay circuit which produces a delay time in d. The circuit a capacitor, an te back resistance, connected serially with the anode of the diode going to ground. At the start of the time delay a negative stepfunction is applied to the series circuit and initiates a half-cycle transient oscillatory voltage terminated by a transient oscillatory voltage of substantially higher frequency. The output of the delay circuit is taken at the junction of the inductor and diode where a sudden voltage rise appears after the initiation of the higher frequency transient oscillations.

Creveling, R.

1959-03-17T23:59:59.000Z

423

Alternative Fuels Data Center: Smithtown Selects CNG to Cut Refuse  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Smithtown Selects CNG Smithtown Selects CNG to Cut Refuse Collection Costs to someone by E-mail Share Alternative Fuels Data Center: Smithtown Selects CNG to Cut Refuse Collection Costs on Facebook Tweet about Alternative Fuels Data Center: Smithtown Selects CNG to Cut Refuse Collection Costs on Twitter Bookmark Alternative Fuels Data Center: Smithtown Selects CNG to Cut Refuse Collection Costs on Google Bookmark Alternative Fuels Data Center: Smithtown Selects CNG to Cut Refuse Collection Costs on Delicious Rank Alternative Fuels Data Center: Smithtown Selects CNG to Cut Refuse Collection Costs on Digg Find More places to share Alternative Fuels Data Center: Smithtown Selects CNG to Cut Refuse Collection Costs on AddThis.com... April 7, 2011 Smithtown Selects CNG to Cut Refuse Collection Costs

424

ARM - Selected Science Team Proposals - FY 1995  

NLE Websites -- All DOE Office Websites (Extended Search)

5 5 Science Research Themes Research Highlights Journal Articles Collaborations Atmospheric System Research (ASR) ARM Science Team Meetings User Meetings Annual Meetings of the Atmospheric System Research (ASR) Science Team and Fall Working Groups Accomplishments Read about the 20 years of accomplishments (PDF, 696KB) from the ARM Program and user facility. Performance Metrics ASR Metrics 2009 2008 2007 2006 Selected Science Team Proposals - FY 1995 Dr. R. Nelson Byrne, SAIC: "Evolution of a New GCM-Capable Stochastic Cloud/Radiation Parameterization Using ARM Data - Phase II" Dr. Steven J. Ghan, Pacific Northwest National Laboratory: "Parameterization of Convective Cloud Coverage in GCMs" Dr. George Golitsyn, Russian Academy of Sciences, Institute of

425

Corrosion reference for geothermal downhole materials selection  

DOE Green Energy (OSTI)

Geothermal downhole conditions that may affect the performance and reliability of selected materials and components used in the drilling, completion, logging, and production of geothermal wells are reviewed. The results of specific research and development efforts aimed at improvement of materials and components for downhole contact with the hostile physicochemical conditions of the geothermal reservoir are discussed. Materials and components covered are tubular goods, stainless steels and non-ferrous metals for high-temperature downhole service, cements for high-temperature geothermal wells, high-temperature elastomers, drilling and completion tools, logging tools, and downhole pumps. (MHR)

Ellis, P.F. II, Smith, C.C.; Keeney, R.C.; Kirk, D.K.; Conover, M.F.

1983-03-01T23:59:59.000Z

426

Aspects of model selection in multivariate analyses  

Science Conference Proceedings (OSTI)

Analysis of data sets that involve large numbers of variables usually entails some type of model fitting and data reduction. In regression problems, a fitted model that is obtained by a selection process can be difficult to evaluate because of optimism induced by the choice mechanism. Problems in areas such as discriminant analysis, calibration, and the like often lead to similar difficulties. The preceeding sections reviewed some of the general ideas behind assessment of regression-type predictors and illustrated how they can be easily incorporated into a standard data analysis.

Picard, R.

1982-01-01T23:59:59.000Z

427

2002 Workshop on Selective Catalytic Reduction  

Science Conference Proceedings (OSTI)

Approximately 100,000 MW of coal-fired generating capacity in the United States will be equipped with selective catalytic reduction (SCR) systems to meet the nitrogen oxides (NOx) limits of the state implementation plan (SIP) call. Approximately 20,000 MW of capacity was expected to go into operation in 2002. Added to early SCR adopters in prior years, about 25 percent of the planned inventory is presently operable. Since 1999, EPRI has organized annual SCR workshops to discuss key issues and development...

2003-01-30T23:59:59.000Z

428

2003 Workshop on Selective Catalytic Reduction  

Science Conference Proceedings (OSTI)

Approximately 105,000 MW of coal-fired generating capacity in the United States will be equipped with selective catalytic reduction (SCR) systems to meet the nitrogen oxide (NOx) limits of the state implementation plan (SIP). Power producers placed approximately 40,000 MW of capacity into operation in 2003. Combined with early SCR adopters from prior years, about 65 percent of the planned inventory is presently operable. Since 1999, EPRI has organized and held annual SCR workshops to discuss key issues a...

2004-02-09T23:59:59.000Z

429

Bayesian model selection and isocurvature perturbations  

E-Print Network (OSTI)

Present cosmological data are well explained assuming purely adiabatic perturbations, but an admixture of isocurvature perturbations is also permitted. We use a Bayesian framework to compare the performance of cosmological models including isocurvature modes with the purely adiabatic case; this framework automatically and consistently penalizes models which use more parameters to fit the data. We compute the Bayesian evidence for fits to a dataset comprised of WMAP and other microwave anisotropy data, the galaxy power spectrum from 2dFGRS and SDSS, and Type Ia supernovae luminosity distances. We find that Bayesian model selection favours the purely adiabatic models, but so far only at low significance.

Maria Beltran; Juan Garcia-Bellido; Julien Lesgourgues; Andrew R Liddle; Anze Slosar

2005-01-24T23:59:59.000Z

430

Time of flight mass spectrometer  

DOE Patents (OSTI)

A time-of-flight mass spectrometer is described in which ions are desorbed from a sample by nuclear fission fragments, such that desorption occurs at the surface of the sample impinged upon by the fission fragments. This configuration allows for the sample to be of any thickness, and eliminates the need for complicated sample preparation.

Ulbricht, Jr., William H. (Arvada, CO)

1984-01-01T23:59:59.000Z

431

The TESLA Time Projection Chamber  

E-Print Network (OSTI)

A large Time Projection Chamber is proposed as part of the tracking system for a detector at the TESLA electron positron linear collider. Different ongoing R&D studies are reviewed, stressing progress made on a new type readout technique based on Micro-Pattern Gas Detectors.

Nabil Ghodbane

2002-12-12T23:59:59.000Z

432

Waste to Energy Time Activities  

E-Print Network (OSTI)

SEMINAR Waste to Energy Time Activities 9:30-9:40 Brief introduction of participants 9:40-10:10 Presentation of Dr. Kalogirou, "Waste to Energy: An Integral Part of Worldwide Sustainable Waste Management" 10. Sofia Bethanis, "Production of synthetic aggregates for use in structural concrete from waste to energy

Columbia University

433

Vocal Timing in the Bat  

E-Print Network (OSTI)

Bats are social organisms that live in large colonies. However, reliance upon echolocation in order to hunt and navigate, means that bats also face pressing acoustic challenges due to overlap with surrounding noise. Bats also possess fine control over the properties of their echolocation pulses. This study's goal was to determine how bats are able to effectively function in large groups despite the interfering noise generated by conspecifics. Mexican free-tailed bats (Tadarida brasiliensis) were exposed to both artificially generated interfering noises and noise generated by conspecifics, and the temporal characteristics of their resulting echolocation calls were analyzed. In addition, bats were given injections of dopaminergic and serotonergic drugs, in an effort to determine which monoamine(s) were capable of altering vocal motor timing and to determine which regions of the brain play a role in regulating the timing of echolocation. I hypothesized that bats would alter the timing of emission of their own echolocation pulses in response to noise, and that drugs affecting the 5HT2A receptor would shift the timing of emission of echolocation pulses. The first part of this dissertation describes a novel temporal alteration behavior that occurs in response to artificially generated intermittent noise, and is characterized by a period of pulse suppression followed by a gradual return to normal call rates. Bats alter the timing of emission of their echolocation pulses to avoid overlap with noise and call within silent periods. The second part of this study investigated whether dopamine or serotonin, or both, could alter the timing of this vocal behavior. The results of this study were inconclusive, although I found some evidence that 5HT2A agonists can produce faster responses. Finally, I show that echolocating bats suppress pulse emission in nearby conspecifics. The resulting decrease in call rate leads to an overall increase in information throughput. This study also demonstrates that bats respond to continuous noise by increasing their call rate, and that the switch between the responses to intermittent noise and continuous noise occurs at a duty cycle of 50% or higher. Overall, this dissertation establishes that bats alter the timing of emission of their echolocation calls in response to noise, and that these mechanisms may be regulated by serotoninergic mechanisms.

Jarvis, Jenna N

2013-05-01T23:59:59.000Z

434

Using quantiles in ranking and selection procedures  

Science Conference Proceedings (OSTI)

A useful performance measure on which to compare manufacturing systems is a quantile of the cycle time distribution. Unfortunately, aside from order statistic estimates, which can require significant data storage, the distribution of quantile estimates ...

Jennifer M. Bekki; John W. Fowler; Gerald T. Mackulak; Barry L. Nelson

2007-12-01T23:59:59.000Z

435

Predictable real-time software synthesis  

Science Conference Proceedings (OSTI)

Formal theories for real-time systems (such as timed process algebra, timed automata and timed petri nets) have gained great success in the modeling of concurrent timing behavior and in the analysis of real-time properties. However, due to the ineliminable ... Keywords: Formal methods, Program synthesis, Real-time systems

Jinfeng Huang; Jeroen Voeten; Henk Corporaal

2007-08-01T23:59:59.000Z

436

Determination of time zero from a charged particle detector  

DOE Patents (OSTI)

A method, system and computer program is used to determine a linear track having a good fit to a most likely or expected path of charged particle passing through a charged particle detector having a plurality of drift cells. Hit signals from the charged particle detector are associated with a particular charged particle track. An initial estimate of time zero is made from these hit signals and linear tracks are then fit to drift radii for each particular time-zero estimate. The linear track having the best fit is then searched and selected and errors in fit and tracking parameters computed. The use of large and expensive fast detectors needed to time zero in the charged particle detectors can be avoided by adopting this method and system.

Green, Jesse Andrew (Los Alamos, NM)

2011-03-15T23:59:59.000Z

437

Flame Retardant Exposure Linked to House Dust  

Science Conference Proceedings (OSTI)

... dwelling or the number of foam cushions or appliances, but smaller dwellings tended ... In particular, the authors note that small children are more ...

2010-10-05T23:59:59.000Z

438

Life Cycle Assessment of Fire Retardants  

Science Conference Proceedings (OSTI)

... Recycling processes Production of primary product Production of primary product Use of primary product ... Hydro Nuclear Crude oil Coal Natural gas ...

2011-11-16T23:59:59.000Z

439

Flame Retardant Materials - Oak Ridge National Laboratory  

replace steel and other metals in automotive and aircraft parts, thus saving weight and fuel. ... industry friendly • Cost-effective Potential Applications

440

Project: Advanced Gas-Phase Fire Retardants  

Science Conference Proceedings (OSTI)

... at understanding the condensed-phase chemistry related to ... Center) on the fundamental mechanisms of ... for the SFPE Handbook: Chemical Kinetics ...

2012-12-31T23:59:59.000Z

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Flame retardant mechanism of polyamide 6–clay ...  

Science Conference Proceedings (OSTI)

... a nitrogen atmos- phere over a temperature range which is close to the ... sample was observed giving it the appearance of a highly viscous mound. ...

2004-06-22T23:59:59.000Z

442

On Forward-in-Time Differencing for Fluids: Stopping Criteria for Iterative Solutions of Anelastic Pressure Equations  

Science Conference Proceedings (OSTI)

In this note, the authors address the practical issue of selecting appropriate stopping criteria for iterative solutions to the elliptic pressure equation arising in nonoscillatory, forward-in-time Eulerian and semi-Lagrangian anelastic fluid ...

Piotr K. Smolarkiewicz; Vanda Grubis?i?; Len G. Margolin

1997-04-01T23:59:59.000Z

443

Mar_13Times.indd  

NLE Websites -- All DOE Office Websites (Extended Search)

MARCH 2013 MARCH 2013 inside this issue ... FIRP draws to a close Page 2 Reminisce: Y-12 turns 70 Page 4 Russia's secret city Page 5 Development retools its CONOPS Page 6 ... and other Y-12 news Miss an issue? Find us online, http://www.y12.doe.gov/news/times.php MISSION, cont. on pg. 2 The National Nuclear Security Administration's Performance Evaluation Report for B&W Y-12, released Feb. 11, gave "Very Good" ratings to B&W Y-12 in areas related to all three core missions: maintaining the nuclear weapons stockpile, powering the nuclear Navy and nonproliferation. The report evaluates B&W Y-12's performance based on the Performance Evaluation Plan approved at the beginning of fi scal 2012. Programs The Y-12 Times highlighted the success of fi

444

High resolution time interval meter  

DOE Patents (OSTI)

Method and apparatus are provided for measuring the time interval between two events to a higher resolution than reliability available from conventional circuits and component. An internal clock pulse is provided at a frequency compatible with conventional component operating frequencies for reliable operation. Lumped constant delay circuits are provided for generating outputs at delay intervals corresponding to the desired high resolution. An initiation START pulse is input to generate first high resolution data. A termination STOP pulse is input to generate second high resolution data. Internal counters count at the low frequency internal clock pulse rate between the START and STOP pulses. The first and second high resolution data are logically combined to directly provide high resolution data to one counter and correct the count in the low resolution counter to obtain a high resolution time interval measurement.

Martin, A.D.

1986-05-09T23:59:59.000Z

445

Time-parareal parallel in time integrator solver for time-dependent neutron diffusion equation  

E-Print Network (OSTI)

-dependent spatial flux distribution in nuclear reactor is required for nuclear safety and design. The motivation present a time-parallel algorithm that simulate the kinetic of neutron2 in a nuclear reactor. We consider engine behavior and in particular its energy4 production.5 The flux distribution on the nuclear reactor

446

Why Time is Future Oriented  

E-Print Network (OSTI)

We assume that the universe consists of clusters which in turns have sub-clusters and the sub-clusters have sub-subclusters and so on. Confining to three-dimensional space, it is shown that the universe is expanding if entropy of the universe increases. It is also shown that clocks slow down when time progresses towards future. Our model also justifies the big bang theory.

Shahid N. Afridi; M. Khalid Khan

2004-12-09T23:59:59.000Z

447

Time and Frequency Division - 1997 Technical Highlights  

Science Conference Proceedings (OSTI)

... have locked a microwave source to the ions' ground state hyperfine ... pseudo-random GPS clock variations associated with Selective Availability ( ...

448

Test methods for selection of materials of construction for high-level radioactive waste vitrification. Revision  

Science Conference Proceedings (OSTI)

Candidate materials of construction were evaluated for a facility at the Department of Energy's Savannah River Plant to vitrify high-level radioactive waste. Limited operating experience was available under the corrosive conditions of the complex vitrification process. The objective of the testing program was to provide a high degree of assurance that equipment will meet or exceed design lifetimes. To meet this objective in reasonable time and minimum cost, a program was designed consisting of a combination of coupon immersion and electrochemical laboratory tests and pilot-scale tests. Stainless steels and nickel-based alloys were tested. Alloys that were most resistant to general and local attack contained nickel, molybdenum (>9%), and chromium (where Cr + Mo > 30%). Alloy C-276 was selected as the reference material for process equipment. Stellite 6 was selected for abrasive service in the presence of formic acid. Alloy 690 and ALLCORR were selected for specific applications.

Bickford, D F; Corbett, R A; Morrison, W S

1986-01-01T23:59:59.000Z

449

New methods for detecting lineage-specific selection  

Science Conference Proceedings (OSTI)

So far, most methods for identifying sequences under selection based on comparative sequence data have either assumed selectional pressures are the same across all branches of a phylogeny, or have focused on changes in specific lineages of interest. ...

Adam Siepel; Katherine S. Pollard; David Haussler

2006-04-01T23:59:59.000Z

450

Selecting a New Water Heater | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

Selecting a New Water Heater Selecting a New Water Heater August 29, 2012 - 7:30pm Addthis Water heater testing facility at Oak Ridge National Laboratory. Water heater testing...

451

FutureGen Industrial Alliance Announces Carbon Storage Site Selection...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

FutureGen Industrial Alliance Announces Carbon Storage Site Selection Process for FutureGen 2.0 FutureGen Industrial Alliance Announces Carbon Storage Site Selection Process for...

452

Tool selectivity in left occipitotemporal cortex develops without vision  

Science Conference Proceedings (OSTI)

Previous studies have provided evidence for a tool-selective region in left lateral occipitotemporal cortex LOTC. This region responds selectively to pictures of tools and to characteristic visual tool motion. The present human fMRI study tested whether ...

Marius V. Peelen; Stefania Bracci; Xueming Lu; Chenxi He; Alfonso Caramazza; Yanchao Bi

2013-08-01T23:59:59.000Z

453

Profilio Selection Using the Adelais Multiobjective Linear Programming System  

Science Conference Proceedings (OSTI)

The ADELAIS (Aide à la DEcision pour systèmes Linéaires multicritères par AIde à la Structuration des préférences), multiobjective linear programming system is proposed as a decision tool for the selection ... Keywords: ADELAIS, portfolio analysis, portfolio selection

C. Zopounidis; D. K. Despotis; I. Kamaratou

1998-06-01T23:59:59.000Z

454

Pavan Balaji selected as TEDxMidwest Emerging Leader | Argonne...  

NLE Websites -- All DOE Office Websites (Extended Search)

selected as TEDxMidwest Emerging Leader May 14, 2013 Tweet EmailPrint Pavan Balaji, a computer scientist in Argonne's Mathematics and Computer Science Division, was selected as a...

455

Does Private Selection Improve the Accuracy of Arbitrators' Decisions?  

E-Print Network (OSTI)

would distort less. Does there exist an equilibrium in whichDoes Private Selection Improve the Accuracy of Arbitrators’problem of biased selection does not address the strategic

Klement, Alon; Neeman, Zvika

2009-01-01T23:59:59.000Z

456

An algorithm for a selective nearest neighbor decision rule (Corresp.)  

Science Conference Proceedings (OSTI)

A procedure is introduced to approximate nearest neighbor (INN) decision boundaries. The algorithm produces a selective subset of the original data so that 1) the subset is consistent, 2) the distance between any sample and its nearest selective neighbor ...

G. Ritter; H. Woodruff; S. Lowry; T. Isenhour

1975-11-01T23:59:59.000Z

457

A Bayesian Approach to Predictor Selection for Seasonal Streamflow Forecasting  

Science Conference Proceedings (OSTI)

Statistical methods commonly used for forecasting climate and streamflows require the selection of appropriate predictors. Poorly designed predictor selection procedures can result in poor forecasts for independent events. This paper introduces a ...

David E. Robertson; Q. J. Wang

2012-02-01T23:59:59.000Z

458

Analytic Controllability of Time-Dependent Quantum Control Systems  

E-Print Network (OSTI)

The question of controllability is investigated for a quantum control system in which the Hamiltonian operator components carry explicit time dependence which is not under the control of an external agent. We consider the general situation in which the state moves in an infinite-dimensional Hilbert space, a drift term is present, and the operators driving the state evolution may be unbounded. However, considerations are restricted by the assumption that there exists an analytic domain, dense in the state space, on which solutions of the controlled Schrodinger equation may be expressed globally in exponential form. The issue of controllability then naturally focuses on the ability to steer the quantum state on a finite-dimensional submanifold of the unit sphere in Hilbert space -- and thus on analytic controllability. A relatively straightforward strategy allows the extension of Lie-algebraic conditions for strong analytic controllability derived earlier for the simpler, time-independent system in which the drift Hamiltonian and the interaction Hamiltonia have no intrinsic time dependence. Enlarging the state space by one dimension corresponding to the time variable, we construct an augmented control system that can be treated as time-independent. Methods developed by Kunita can then be implemented to establish controllability conditions for the one-dimension-reduced system defined by the original time-dependent Schrodinger control problem. The applicability of the resulting theorem is illustrated with selected examples.

Chunhua Lan; Tzyh-Jong Tarn; Quo-Shin Chi; John W. Clark

2004-09-22T23:59:59.000Z

459

General Interest NIST Time and Frequency Publications  

Science Conference Proceedings (OSTI)

... Time and Frequency Users Manual A detailed ... Fundamentals of Time and Frequency An overview of ... Lombardi, The Mechatronics Handbook, 2001. ...

2012-01-31T23:59:59.000Z

460

Anchorless Selective Laser Melting, a Method for the Removal of ...  

Science Conference Proceedings (OSTI)

About this Abstract. Meeting, Materials Science & Technology 2012. Symposium, Additive Manufacturing of Metals. Presentation Title, Anchorless Selective ...

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

NIST ICDB: Select Countries from which to Download ...  

Science Conference Proceedings (OSTI)

... Select Countries for Document Download for Electricity & Magnetism. Below is an alphabetical list of all of the countries ...

462

Microstructure of Titanium Alloy Prepared by Selective Laser Melting ...  

Science Conference Proceedings (OSTI)

Symposium, Solidification in Additive Manufacturing. Presentation Title, Microstructure of Titanium Alloy Prepared by Selective Laser Melting in Vacuum.

463

Sustainability Study in Selective Laser Sintering – An Energy ...  

Science Conference Proceedings (OSTI)

Presentation Title, Sustainability Study in Selective Laser Sintering – An Energy ... 2010 Vittorio de Nora Award Winner: Designing Crushing and Grinding ...

464

NNSA Announces Selection of Centers of Excellence for Academic...  

NLE Websites -- All DOE Office Websites (Extended Search)

Announces Selection of Centers of Excellence for Academic Computational Science Partnerships | National Nuclear Security Administration Our Mission Managing the Stockpile...

465

CNST High School Intern Parakh Jain Selected as Semifinalist ...  

Science Conference Proceedings (OSTI)

CNST High School Intern Parakh Jain Selected as Semifinalist in Intel Science Talent Search. For Immediate Release: January 31, 2011. ...

2011-01-31T23:59:59.000Z

466

Uranium Metal Analysis via Selective Dissolution  

DOE Green Energy (OSTI)

Uranium metal, which is present in sludge held in the Hanford Site K West Basin, can create hazardous hydrogen atmospheres during sludge handling, immobilization, or subsequent transport and storage operations by its oxidation/corrosion in water. A thorough knowledge of the uranium metal concentration in sludge therefore is essential to successful sludge management and waste process design. The goal of this work was to establish a rapid routine analytical method to determine uranium metal concentrations as low as 0.03 wt% in sludge even in the presence of up to 1000-fold higher total uranium concentrations (i.e., up to 30 wt% and more uranium) for samples to be taken during the upcoming sludge characterization campaign and in future analyses for sludge handling and processing. This report describes the experiments and results obtained in developing the selective dissolution technique to determine uranium metal concentration in K Basin sludge.

Delegard, Calvin H.; Sinkov, Sergey I.; Schmidt, Andrew J.; Chenault, Jeffrey W.

2008-09-10T23:59:59.000Z

467

Optimal Portfolio Selection Under Concave Price Impact  

SciTech Connect

In this paper we study an optimal portfolio selection problem under instantaneous price impact. Based on some empirical analysis in the literature, we model such impact as a concave function of the trading size when the trading size is small. The price impact can be thought of as either a liquidity cost or a transaction cost, but the concavity nature of the cost leads to some fundamental difference from those in the existing literature. We show that the problem can be reduced to an impulse control problem, but without fixed cost, and that the value function is a viscosity solution to a special type of Quasi-Variational Inequality (QVI). We also prove directly (without using the solution to the QVI) that the optimal strategy exists and more importantly, despite the absence of a fixed cost, it is still in a 'piecewise constant' form, reflecting a more practical perspective.

Ma Jin, E-mail: jinma@usc.edu [University of Southern California, Department of Mathematics (United States); Song Qingshuo, E-mail: songe.qingshuo@cityu.edu.hk [City University of Hong Kong, Department of Mathematics (Hong Kong); Xu Jing, E-mail: xujing8023@yahoo.com.cn [Chongqing University, School of Economics and Business Administration (China); Zhang Jianfeng, E-mail: jianfenz@usc.edu [University of Southern California, Department of Mathematics (United States)

2013-06-15T23:59:59.000Z

468

Information criteria for astrophysical model selection  

E-Print Network (OSTI)

Model selection is the problem of distinguishing competing models, perhaps featuring different numbers of parameters. The statistics literature contains two distinct sets of tools, those based on information theory such as the Akaike Information Criterion (AIC), and those on Bayesian inference such as the Bayesian evidence and Bayesian Information Criterion (BIC). The Deviance Information Criterion combines ideas from both heritages; it is readily computed from Monte Carlo posterior samples and, unlike the AIC and BIC, allows for parameter degeneracy. I describe the properties of the information criteria, and as an example compute them from WMAP3 data for several cosmological models. I find that at present the information theory and Bayesian approaches give significantly different conclusions from that data.

Andrew R Liddle

2007-01-04T23:59:59.000Z

469

Selected Isotopes for Optimized Fuel Assembly Tags  

SciTech Connect

In support of our ongoing signatures project we present information on 3 isotopes selected for possible application in optimized tags that could be applied to fuel assemblies to provide an objective measure of burnup. 1. Important factors for an optimized tag are compatibility with the reactor environment (corrosion resistance), low radioactive activation, at least 2 stable isotopes, moderate neutron absorption cross-section, which gives significant changes in isotope ratios over typical fuel assembly irradiation levels, and ease of measurement in the SIMS machine 2. From the candidate isotopes presented in the 3rd FY 08 Quarterly Report, the most promising appear to be Titanium, Hafnium, and Platinum. The other candidate isotopes (Iron, Tungsten, exhibited inadequate corrosion resistance and/or had neutron capture cross-sections either too high or too low for the burnup range of interest.

Gerlach, David C.; Mitchell, Mark R.; Reid, Bruce D.; Gesh, Christopher J.; Hurley, David E.

2008-10-01T23:59:59.000Z

470

Scintillating 99Tc Selective Ion Exchange Resins  

Science Conference Proceedings (OSTI)

Scintillating technetium (99Tc) selective ion exchange resins have been developed and evaluated for equilibrium capacities and detection efficiencies. These resins can be utilized for the in-situ concentration and detection of low levels of pertechnetate anions (99TcO4-) in natural waters. Three different polystyrene type resin support materials were impregnated with varying amounts of tricaprylmethylammonium chloride (Aliquat 336) extractant, several different scintillating fluors and wavelength shifters. The prepared resins were contacted batch-wise to equilibrium over a wide range of 99TcO4- concentrations in natural water. The measured capacities were used to develop Langmuir adsorption isotherms for each resin. 99Tc detection efficiencies were determined and up to 71.4 ± 2.6% was achieved with some resins. The results demonstrate that a low level detection limit for 99TcO4- in natural waters can be realized.

Mitchell Greenhalgh; Richard D. Tillotson

2012-07-01T23:59:59.000Z

471

A Spintronic Semiconductor with Selectable Charge Carriers  

NLE Websites -- All DOE Office Websites (Extended Search)

A Spintronic Semiconductor with Selectable Charge Carriers Print A Spintronic Semiconductor with Selectable Charge Carriers Print Accentuating the Positive (or the Negative) Spintronics-a type of electronics that makes use of electron spin as well as charge-is already here to a certain extent. The discovery of giant magnetoresistance, a spin-based effect, has revolutionized the information storage industry. Beyond this, however, scientists envision the possibility of combining storage and processing functions in one integrated system. In electronics, processing is done using semiconductor materials like silicon and germanium that have the requisite properties to perform logical operations with both electrons (negative n-type charge carriers) and holes (positive p-type charge carriers). Thus, a spintronically desirable semiconductor would simultaneously have discrete spin-up and spin-down states as well as both positive and negative charge carriers. Strategies for developing spintronic semiconductors have been based on surface doping or on alloying, both of which have drawbacks such as chemical instability or reduced mobility. In BiTeI, however, electron and hole conduction is achieved without modifying the ideal crystal structure. One of the things discovered by Crepaldi et al. was that the electronic band structure of BiTeI bends in different ways near the surface depending on which layer is on top. That, in turn, means that the Fermi level (which determines a material's conductivity) can be located in either the valence band (for positive charge carriers) or the conduction band (for negative charge carriers). With techniques such as molecular-beam epitaxy and chemical vapor deposition, it is realistic to consider that regions with opposite band bending could be patterned on a substrate, opening new possibilities for the manipulation of spin-polarized states.

472

A Spintronic Semiconductor with Selectable Charge Carriers  

NLE Websites -- All DOE Office Websites (Extended Search)

A Spintronic Semiconductor with Selectable Charge Carriers Print A Spintronic Semiconductor with Selectable Charge Carriers Print Accentuating the Positive (or the Negative) Spintronics-a type of electronics that makes use of electron spin as well as charge-is already here to a certain extent. The discovery of giant magnetoresistance, a spin-based effect, has revolutionized the information storage industry. Beyond this, however, scientists envision the possibility of combining storage and processing functions in one integrated system. In electronics, processing is done using semiconductor materials like silicon and germanium that have the requisite properties to perform logical operations with both electrons (negative n-type charge carriers) and holes (positive p-type charge carriers). Thus, a spintronically desirable semiconductor would simultaneously have discrete spin-up and spin-down states as well as both positive and negative charge carriers. Strategies for developing spintronic semiconductors have been based on surface doping or on alloying, both of which have drawbacks such as chemical instability or reduced mobility. In BiTeI, however, electron and hole conduction is achieved without modifying the ideal crystal structure. One of the things discovered by Crepaldi et al. was that the electronic band structure of BiTeI bends in different ways near the surface depending on which layer is on top. That, in turn, means that the Fermi level (which determines a material's conductivity) can be located in either the valence band (for positive charge carriers) or the conduction band (for negative charge carriers). With techniques such as molecular-beam epitaxy and chemical vapor deposition, it is realistic to consider that regions with opposite band bending could be patterned on a substrate, opening new possibilities for the manipulation of spin-polarized states.

473

A Spintronic Semiconductor with Selectable Charge Carriers  

NLE Websites -- All DOE Office Websites (Extended Search)

A Spintronic Semiconductor with Selectable Charge Carriers Print A Spintronic Semiconductor with Selectable Charge Carriers Print Accentuating the Positive (or the Negative) Spintronics-a type of electronics that makes use of electron spin as well as charge-is already here to a certain extent. The discovery of giant magnetoresistance, a spin-based effect, has revolutionized the information storage industry. Beyond this, however, scientists envision the possibility of combining storage and processing functions in one integrated system. In electronics, processing is done using semiconductor materials like silicon and germanium that have the requisite properties to perform logical operations with both electrons (negative n-type charge carriers) and holes (positive p-type charge carriers). Thus, a spintronically desirable semiconductor would simultaneously have discrete spin-up and spin-down states as well as both positive and negative charge carriers. Strategies for developing spintronic semiconductors have been based on surface doping or on alloying, both of which have drawbacks such as chemical instability or reduced mobility. In BiTeI, however, electron and hole conduction is achieved without modifying the ideal crystal structure. One of the things discovered by Crepaldi et al. was that the electronic band structure of BiTeI bends in different ways near the surface depending on which layer is on top. That, in turn, means that the Fermi level (which determines a material's conductivity) can be located in either the valence band (for positive charge carriers) or the conduction band (for negative charge carriers). With techniques such as molecular-beam epitaxy and chemical vapor deposition, it is realistic to consider that regions with opposite band bending could be patterned on a substrate, opening new possibilities for the manipulation of spin-polarized states.

474

A Spintronic Semiconductor with Selectable Charge Carriers  

NLE Websites -- All DOE Office Websites (Extended Search)

A Spintronic Semiconductor with Selectable Charge Carriers Print A Spintronic Semiconductor with Selectable Charge Carriers Print Accentuating the Positive (or the Negative) Spintronics-a type of electronics that makes use of electron spin as well as charge-is already here to a certain extent. The discovery of giant magnetoresistance, a spin-based effect, has revolutionized the information storage industry. Beyond this, however, scientists envision the possibility of combining storage and processing functions in one integrated system. In electronics, processing is done using semiconductor materials like silicon and germanium that have the requisite properties to perform logical operations with both electrons (negative n-type charge carriers) and holes (positive p-type charge carriers). Thus, a spintronically desirable semiconductor would simultaneously have discrete spin-up and spin-down states as well as both positive and negative charge carriers. Strategies for developing spintronic semiconductors have been based on surface doping or on alloying, both of which have drawbacks such as chemical instability or reduced mobility. In BiTeI, however, electron and hole conduction is achieved without modifying the ideal crystal structure. One of the things discovered by Crepaldi et al. was that the electronic band structure of BiTeI bends in different ways near the surface depending on which layer is on top. That, in turn, means that the Fermi level (which determines a material's conductivity) can be located in either the valence band (for positive charge carriers) or the conduction band (for negative charge carriers). With techniques such as molecular-beam epitaxy and chemical vapor deposition, it is realistic to consider that regions with opposite band bending could be patterned on a substrate, opening new possibilities for the manipulation of spin-polarized states.

475

Selection of non-adsorbing alkali components  

Science Conference Proceedings (OSTI)

This project consists of three phases of laboratory experimental study. In phase I (screening), eight candidate materials, 304SS (serves as a base material for comparison), Hastelloy C-276, Hastelloy X, Haynes No. 188, Allonized 304SS, Pt-coated 304SS, and ceramic-coated 304SS, will be subjected to atmospheric TGA study under the simulated PFBC (oxidizing) environment with and without alkali vapor doping. Each candidate material will be evaluated for its resistance toward alkali-vapor capture. In addition, a post-test metallographic characterization of the sample will be performed to obtain a better understanding of the alkali capture mechanism and material behavior. The material(s) with little or no alkali-vapor adsorption will be selected as the promising material(s) for the Phase II study. In Phase II, the promising material(s) will be further tested in the TGA under elevated pressure to simulate the PFBC environment (in terms of temperature, pressure, and gas composition). The effect of pressure on the extent of alkali-vapor adsorption will be evaluated, and the test samples will be metallographically characterized. The most promising candidate material(s) will be identified and recommended for further tesfing in the actual PFBC environment. In Phase III, four materials will be selected from the eight candidate materials screened in the PFBC environment and will be evaluated for their alkali-vapor capture by atmospheric TGA under the coal gasification fuel gas (reducing) environment. The tested samples will also be metallographically characterized. The most promising material(s) will be identified and recommended for further testing in the actual coal gasification environment.

Lee, S.H.D.; Natesan, K.; Swift, W.M.

1992-11-01T23:59:59.000Z

476

Selection of non-adsorbing alkali components  

Science Conference Proceedings (OSTI)

This project consists of three phases of laboratory experimental study. In phase I (screening), eight candidate materials, 304SS (serves as a base material for comparison), Hastelloy C-276, Hastelloy X, Haynes No. 188, Allonized 304SS, Pt-coated 304SS, and ceramic-coated 304SS, will be subjected to atmospheric TGA study under the simulated PFBC (oxidizing) environment with and without alkali vapor doping. Each candidate material will be evaluated for its resistance toward alkali-vapor capture. In addition, a post-test metallographic characterization of the sample will be performed to obtain a better understanding of the alkali capture mechanism and material behavior. The material(s) with little or no alkali-vapor adsorption will be selected as the promising material(s) for the Phase II study. In Phase II, the promising material(s) will be further tested in the TGA under elevated pressure to simulate the PFBC environment (in terms of temperature, pressure, and gas composition). The effect of pressure on the extent of alkali-vapor adsorption will be evaluated, and the test samples will be metallographically characterized. The most promising candidate material(s) will be identified and recommended for further tesfing in the actual PFBC environment. In Phase III, four materials will be selected from the eight candidate materials screened in the PFBC environment and will be evaluated for their alkali-vapor capture by atmospheric TGA under the coal gasification fuel gas (reducing) environment. The tested samples will also be metallographically characterized. The most promising material(s) will be identified and recommended for further testing in the actual coal gasification environment.

Lee, S.H.D.; Natesan, K.; Swift, W.M.

1992-01-01T23:59:59.000Z

477

A Spintronic Semiconductor with Selectable Charge Carriers  

NLE Websites -- All DOE Office Websites (Extended Search)

A Spintronic Semiconductor with Selectable Charge Carriers Print A Spintronic Semiconductor with Selectable Charge Carriers Print Accentuating the Positive (or the Negative) Spintronics-a type of electronics that makes use of electron spin as well as charge-is already here to a certain extent. The discovery of giant magnetoresistance, a spin-based effect, has revolutionized the information storage industry. Beyond this, however, scientists envision the possibility of combining storage and processing functions in one integrated system. In electronics, processing is done using semiconductor materials like silicon and germanium that have the requisite properties to perform logical operations with both electrons (negative n-type charge carriers) and holes (positive p-type charge carriers). Thus, a spintronically desirable semiconductor would simultaneously have discrete spin-up and spin-down states as well as both positive and negative charge carriers. Strategies for developing spintronic semiconductors have been based on surface doping or on alloying, both of which have drawbacks such as chemical instability or reduced mobility. In BiTeI, however, electron and hole conduction is achieved without modifying the ideal crystal structure. One of the things discovered by Crepaldi et al. was that the electronic band structure of BiTeI bends in different ways near the surface depending on which layer is on top. That, in turn, means that the Fermi level (which determines a material's conductivity) can be located in either the valence band (for positive charge carriers) or the conduction band (for negative charge carriers). With techniques such as molecular-beam epitaxy and chemical vapor deposition, it is realistic to consider that regions with opposite band bending could be patterned on a substrate, opening new possibilities for the manipulation of spin-polarized states.

478

A Spintronic Semiconductor with Selectable Charge Carriers  

NLE Websites -- All DOE Office Websites (Extended Search)

A Spintronic Semiconductor with Selectable Charge Carriers Print A Spintronic Semiconductor with Selectable Charge Carriers Print Accentuating the Positive (or the Negative) Spintronics-a type of electronics that makes use of electron spin as well as charge-is already here to a certain extent. The discovery of giant magnetoresistance, a spin-based effect, has revolutionized the information storage industry. Beyond this, however, scientists envision the possibility of combining storage and processing functions in one integrated system. In electronics, processing is done using semiconductor materials like silicon and germanium that have the requisite properties to perform logical operations with both electrons (negative n-type charge carriers) and holes (positive p-type charge carriers). Thus, a spintronically desirable semiconductor would simultaneously have discrete spin-up and spin-down states as well as both positive and negative charge carriers. Strategies for developing spintronic semiconductors have been based on surface doping or on alloying, both of which have drawbacks such as chemical instability or reduced mobility. In BiTeI, however, electron and hole conduction is achieved without modifying the ideal crystal structure. One of the things discovered by Crepaldi et al. was that the electronic band structure of BiTeI bends in different ways near the surface depending on which layer is on top. That, in turn, means that the Fermi level (which determines a material's conductivity) can be located in either the valence band (for positive charge carriers) or the conduction band (for negative charge carriers). With techniques such as molecular-beam epitaxy and chemical vapor deposition, it is realistic to consider that regions with opposite band bending could be patterned on a substrate, opening new possibilities for the manipulation of spin-polarized states.

479

An R&D Project Management and Selection System for the Utilization Technology Branch, Division of Geothermal Energy, Volume III - Project Selection Procedure and Benefit/Cost Analysis  

DOE Green Energy (OSTI)

This report in three volumes describes an R and D project management and selection system developed for the Utilization Technology Branch of the Division of Geothermal Energy, Department of Energy. The proposed project management system (PMS) consists of a project data system (PDS) and a project selection procedure (PSP). The project data system consists of a series of project data forms and project status logs, and descriptions of information pathways. The PDS emphasizes timely monitoring of the technical and financial progress of projects, maintenance of the history of the project and rapid access to project information to facilitate responsive reporting to DGE and DOE Upper Management. The project selection procedure emphasizes a R and D product-oriented approach to benefit/cost analysis of individual projects. The report includes: (a) a description of the system, and recommendations for its implementation, (b) the PDS forms and explanation of their use, (c) a glossary of terms for use on the forms, (d) a description of the benefit/cost approach, (e) a data base for estimating R and D benefits, and (f) examples of test applications of the system to nine current DGE projects. This volume describes a proposed procedure for R and D project selection. The benefit/cost analysis part of the procedure estimates financial savings expected to result from the commercial use of hardware or process products of R and D. Savings are estimated with respect to the geothermal power plants expected to come on line between 1978 and 2000.

Dhillon, Harpal S.; Entingh, Daniel J.

1978-05-01T23:59:59.000Z

480

Selection based heuristics for the non-unique oligonucleotide probe selection problem in microarray design  

Science Conference Proceedings (OSTI)

In order to accurately measure the gene expression levels in microarray experiments, it is crucial to design unique, highly specific and highly sensitive oligonucleotide probes for the identification of biological agents such as genes in a sample. Unique ... Keywords: Coverage, Heuristic, Microarray, Probe, Selection, Separation

Alioune Ngom; Luis Rueda; Lili Wang; Robin Gras

2010-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "timing retard selective" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

" Row: Selected SIC Codes; Column: Energy Sources;"  

U.S. Energy Information Administration (EIA) Indexed Site

S5.1. Selected Byproducts in Fuel Consumption, 1998;" S5.1. Selected Byproducts in Fuel Consumption, 1998;" " Level: National Data; " " Row: Selected SIC Codes; Column: Energy Sources;" " Unit: Trillion Btu." " "," "," "," "," "," "," "," ","Waste"," ",," " " "," "," ","Blast"," "," ","Pulping Liquor"," ","Oils/Tars","RSE" "SIC"," "," ","Furnace/Coke"," ","Petroleum","or","Wood Chips,","and Waste","Row"

482

Selective thermal and photooxidation of hydrocarbons in zeolites by oxygen  

DOE Patents (OSTI)

A process for selective thermal oxidation or photooxidation of hydrocarbons adsorbed onto zeolite matrices. A highly selective thermal oxidation and photooxidation of unsubstituted or alkyl substituted alkanes, alkenes, aromatics and cycloalkyls in solvent free zeolites under dark thermal conditions or under irradiation with visible light. The process oxidizes hydrocarbons almost completely selectively without substantial production of byproducts.

Frei, Heinz (Berkeley, CA); Blatter, Fritz (Basel, CH); Sun, Hai (Saint Charles, MO)

1999-01-01T23:59:59.000Z

483

Selective thermal and photooxidation of hydrocarbons in zeolites by oxygen  

DOE Patents (OSTI)

A process for a combined selective thermal oxidation and photooxidation of hydrocarbons adsorbed onto zeolite matrices. A highly combined selective thermal oxidation and photooxidation of unsubstituted or alkyl substituted alkanes, alkenes, aromatics and cycloalkyls in solvent free zeolites under dark thermal conditions or under irradiation with visible light. The process oxidizes hydrocarbons almost completely selectively without substantial production of byproducts.

Frei, Heinz (Berkeley, CA); Blatter, Fritz (Basel, CH); Sun, Hai (Saint Charles, MO)

2001-01-01T23:59:59.000Z

484

Selective thermal oxidation of hydrocarbons in zeolites by oxygen  

DOE Patents (OSTI)

A process for selective thermal oxidation of hydrocarbons adsorbed onto zeolite matrices. A highly selective thermal oxidation of unsubstituted or alkyl substituted alkanes, alkenes, aromatics and cycloalkyls is carried out in solvent free zeolites under dark thermal conditions. The process oxidizes hydrocarbons almost completely selectively without substantial production of byproducts.

Frei, Heinz (Berkeley, CA); Blatter, Fritz (Basel, CH); Sun, Hai (Saint Charles, MO)

2000-01-01T23:59:59.000Z

485

A multicriteria methodology for equity selection using financial analysis  

Science Conference Proceedings (OSTI)

In this article we present a multiple criteria methodology for supporting decisions that concern the selection of equities, on the basis of financial analysis. The ELECTRE Tri outranking classification method is employed for selecting the attractive ... Keywords: Equity portfolio selection, Financial analysis, Multiple criteria decision making

Panagiotis Xidonas; George Mavrotas; John Psarras

2009-12-01T23:59:59.000Z

486

A Heuristic for Clock Selection in High-Level Synthesis  

Science Conference Proceedings (OSTI)

Clock selection has a significant impact on the performance and quality of designs in high-level synthesis. In most synthesis systems, a convenient value of the clock is chosen or exact (and expensive) methods have been used for clock selection. This ... Keywords: high-level synthesis, clock selection, graph structure, design space exploration, heuristics

J. Ramanujam; Sandeep Deshpande; Jinpyo Hong; Mahmut Kandemir

2002-01-01T23:59:59.000Z

487

HASE: A Hybrid Approach to Selectivity Estimation for Conjunctive Predicates  

E-Print Network (OSTI)

be the conjuncts of predicates in which attributes in U are involved. Then the selectivity s U of PU canHASE: A Hybrid Approach to Selectivity Estimation for Conjunctive Predicates Xiaohui Yu 1 , Nick, Canada calisto@ca.ibm.com Abstract. Current methods for selectivity estimation fall into two broad

Yu, Xiaohui

488

HASE: A Hybrid Approach to Selectivity Estimation for Conjunctive Predicates  

E-Print Network (OSTI)

. Then the selectivity sU of PU can be estimated based on the synopsis on U. We augment the auxiliary vector xjHASE: A Hybrid Approach to Selectivity Estimation for Conjunctive Predicates Xiaohui Yu1 , Nick, Canada calisto@ca.ibm.com Abstract. Current methods for selectivity estimation fall into two broad

Yu, Xiaohui

489

SELECTIVE MECHANISMS FOR COMPLEX VISUAL PATTERNS REVEALED BY ADAPTATION  

E-Print Network (OSTI)

part of a separate system). Olzak and Thomas (1999) suggest a model for a pu- tative plaid-form-selectiveSELECTIVE MECHANISMS FOR COMPLEX VISUAL PATTERNS REVEALED BY ADAPTATION J. W. PEIRCE* AND L. J that humans have neural mech- anisms selectively tuned to simple patterns of particular spa- tial frequencies

Nottingham, University of

490

Minimizing Bank Selection Instructions for Partitioned Memory Architectures  

E-Print Network (OSTI)

selection instructions. The main idea is that we introduce two controlling variables Pu and Qu for every upon exit. Depending on the values of Pu and Qu we insert bank selection instructions according is performed. Other- 5 #12;wise they return the cost cu of a bank selection instruction. n-costu(Pu) = ( cu

Burgstaller, Bernd

491

Semiparametric Bayesian Analysis of Selection Models Jaeyong Lee  

E-Print Network (OSTI)

Semiparametric Bayesian Analysis of Selection Models Jaeyong Lee National Institute of Statistical Science James O. Berger Duke University Abstract Selection models are appropriate when a datum x enters it to be of some particular functional form. By introducing latent variables related to the selection mechanism

Berger, Jim

492

Approximating Selective Sweeps by Richard Durrett and Jason Schweinsberg  

E-Print Network (OSTI)

Approximating Selective Sweeps by Richard Durrett and Jason Schweinsberg Dept. of Math, Cornell U of selective sweeps on genealogies. However, most subsequent work has simplified their approach by assuming that the impact of a selective sweep can be accurately approximated by a random partition created by a stick

Durrett, Richard

493

Bayesian Variable Selection and the Swendsen-Wang Algorithm  

E-Print Network (OSTI)

Bayesian Variable Selection and the Swendsen-Wang Algorithm David J. NOTT and Peter J. GREEN improvements in Markov chain Monte Carlo sampling algorithms for Bayesian variable selection. Currently used, this excludes the ith predictor from the model. The problem of variable selection is to decide which predictors

Green, Peter

494

SELECTING A CONSULTANT IN THE RESOURCE RECOVERY FIELD  

E-Print Network (OSTI)

SELECTING A CONSULTANT IN THE RESOURCE RECOVERY FIELD HENRY V. TEASE Combustion Engineering, Inc. Windsor, Connecticut ABSTRACT This paper outlines a set of criteria which can be used to select used to select a construc tion manager for a large resource recovery project. BACKGROUND Interest

Columbia University

495

-lookdown model with selection B. Bah and E. Pardoux  

E-Print Network (OSTI)

-lookdown model with selection B. Bah and E. Pardoux March 8, 2013 Abstract The goal of this paper is to study the lookdown model with selection in the case of a population containing two types of individuals "- lookdown model with selection". When the measure gives no mass to 0, we show that the proportion of one

Pardoux, Etienne

496

Bayesian variable selection and the Swendsen-Wang algorithm  

E-Print Network (OSTI)

Bayesian variable selection and the Swendsen-Wang algorithm David J. Nott1 and Peter J. Green2 1 motivated improvements in Markov chain Monte Carlo sampling algorithms for Bayesian variable selection. Traditional sampling al- gorithms for Bayesian variable selection may perform poorly when there are severe

Barber, Stuart

497

A methodology for the selection and optimisation of  

E-Print Network (OSTI)

A methodology for the selection and optimisation of countermeasure strategies G. M. COX, N. M. J the selection of sustainable, long-term management and restoration strategies for radioactively contaminated dose received by the population. The countermeasures selected, and their level of implementation, can

Crout, Neil

498

Optimal selection of robots by using distance based approach method  

Science Conference Proceedings (OSTI)

A deterministic quantitative model based on Distance Based Approach (DBA) method has been developed for evaluation, selection and ranking of robots, which is a concept hitherto not employed in selection problem of this kind. As a significant development ... Keywords: Distance based approach, Optimized selection, Ranking, Robots

Rishi Kumar; R. K. Garg

2010-10-01T23:59:59.000Z

499

Selective thermal and photooxidation of hydrocarbons in zeolites by oxygen  

DOE Patents (OSTI)

A process is described for selective thermal oxidation or photooxidation of hydrocarbons adsorbed onto zeolite matrices. A highly selective thermal oxidation and photooxidation of unsubstituted or alkyl substituted alkanes, alkenes, aromatics and cycloalkyls in solvent free zeolites under dark thermal conditions or under irradiation with visible light. The process oxidizes hydrocarbons almost completely selectively without substantial production of byproducts. 19 figs.

Frei, H.; Blatter, F.; Sun, H.

1999-06-22T23:59:59.000Z

500

Real time infrared aerosol analyzer  

DOE Patents (OSTI)

Apparatus for analyzing aerosols in essentially real time includes a virtual impactor which separates coarse particles from fine and ultrafine particles in an aerosol sample. The coarse and ultrafine particles are captured in PTFE filters, and the fine particles impact onto an internal light reflection element. The composition and quantity of the particles on the PTFE filter and on the internal reflection element are measured by alternately passing infrared light through the filter and the internal light reflection element, and analyzing the light through infrared spectrophotometry to identify the particles in the sample.

Johnson, Stanley A. (Countryside, IL); Reedy, Gerald T. (Bourbonnais, IL); Kumar, Romesh (Naperville, IL)

1990-01-01T23:59:59.000Z