National Library of Energy BETA

Sample records for ti ma te

  1. MA.+'

    Office of Legacy Management (LM)

    MA.+' t -@ . ;' OAK RIDGE NATIONAL LABORATORY i OPtRATED BY MARTIN MARIETTA ENERGY SYSTEMS, INC. FOR THE UNITE0 STATES DEPARTMENT OF ENERGY ,,y , - IhI of ORNLTM-10053 RESULTS OF ...

  2. Resonance photoelectron spectroscopy of TiX{sub 2} (X = S, Se, Te) titanium dichalcogenides

    SciTech Connect (OSTI)

    Shkvarin, A. S. Yarmoshenko, Yu. M.; Skorikov, N. A.; Yablonskikh, M. V.; Merentsov, A. I.; Shkvarina, E. G.; Titov, A. N.

    2012-11-15

    The photoelectron valence band spectra of TiS{sub 2}, TiSe{sub 2}, and TiTe{sub 2} dichalcogenides are investigated in the Ti 2p-3d resonance regime. Resonance bands in the vicinity of the Fermi energy are found for TiS{sub 2} and TiTe{sub 2}. The nature of these bands is analyzed based on model calculations of the density of electronic states in TiS{sub 2}, TiSe{sub 2}, and TiTe{sub 2} compounds intercalated by titanium atoms. Analysis of experimental data and their comparison with model calculations showed that these bands have different origins. It is found that the resonance enhancement of an additional band observed in TiS{sub 2} is explained by self-intercalation by titanium during the synthesis of this compound. The resonance enhancement in TiTe{sub 2} is caused by occupation of the 3d band in Ti.

  3. Effects of Cu Diffusion from ZnTe:Cu/Ti Contacts on Carrier Lifetime of CdS/CdTe Thin Film Solar Cells: Preprint

    SciTech Connect (OSTI)

    Gessert, T. A.; Metzger, W. K.; Asher, S. E.; Young, M. R.; Johnston, S.; Dhere, R. G.; Duda, A.

    2008-05-01

    We study the performance of CdS/CdTe thin film PV devices processed with a ZnTe:Cu/Ti contact to investigate how carrier lifetime in the CdTe layer is affected by Cu diffusion from the contact.

  4. MA AP MA MA MA AP AP MA MA MA AP AP

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AP MA MA MA AP AP MA MA MA AP AP low low low AP MA Run PAMM AP Low alpha University Holidays APPAMM Spear Down Hrs S 30 31 S 30 5260 832 6092 2013 2014 Scheduled Hours Users...

  5. Electronic structure of titanium dichalcogenides TiX{sub 2} (X = S, Se, Te)

    SciTech Connect (OSTI)

    Shkvarin, A. S. Yarmoshenko, Yu. M.; Skorikov, N. A.; Yablonskikh, M. V.; Merentsov, A. I.; Shkvarina, E. G.; Titov, A. N.

    2012-01-15

    The electronic structure and the chemical bond in titanium dichalcogenides TiX{sub 2} (X = S, Se, Te), which are promising electrode materials for lithium batteries, are studied experimentally and theoretically. It is found that the X-ray photoelectron spectra of the valence bands and the core levels of titanium and its X-ray L{sub 2,3} absorption spectra demonstrate a change in the ionic and covalent components of the chemical bond in these compounds. The densities of states in these compounds are calculated by the full-potential augmented-plane-wave method, and multiplet calculations of the X-ray L{sub 2,3} absorption spectra of titanium are performed. It is shown that, in the row TiS{sub 2}-TiSe{sub 2}-TiTe{sub 2}, the covalence increases, the ionicity of the chemical bond decreases, and the effect of the crystal field of a ligand is weakened.

  6. Magneto-optical characterizations of FeTe???Se??? thin films with critical current density over 1 MA/cm

    SciTech Connect (OSTI)

    Sun, Yue; Li, Qiang; Tsuchiya, Yuji; Pyon, Sunseng; Tamegai, Tsuyoshi; Zhang, Cheng; Ozaki, Toshinori

    2015-01-01

    We performed magneto-optical (MO) measurements on FeTe???Se??? thin films grown on LaAlO? (LAO) and Yttria-stabilized zirconia (YSZ) single-crystalline substrates. These thin films show superconducting transition temperature Tc ~19 K, 4 K higher than the bulk sample. Typical roof-top patterns can be observed in the MO images of thin films grown on LAO and YSZ, from which a large and homogeneous critical current density Jc ~ 3 - 4 x 10? A/cm at 5 K was obtained. Magnetic flux penetration measurement reveals that the current is almost isotropically distributed in the two thin films. Compared with bulk crystals, FeTe???Se??? thin film demonstrates not only higher Tc, but also much larger Jc, which is attractive for applications.

  7. High thermal stability Sb{sub 3}Te-TiN{sub 2} material for phase change memory application

    SciTech Connect (OSTI)

    Ji, Xinglong; Zhou, Wangyang; Wu, Liangcai Zhu, Min; Rao, Feng; Song, Zhitang; Cao, Liangliang; Feng, Songlin

    2015-01-12

    For phase change memory (PCM) applications, it has been widely accepted that δ phase Sb-Te has fast operation speed and good phase stability. However, the fast growth crystallization mechanism will cause poor amorphous phase stability and overlarge grain size. We introduce TiN{sub 2} into δ phase Sb-Te (Sb{sub 3}Te) to enhance the amorphous thermal stability and refine the grain size. With TiN{sub 2} incorporating, the temperature for 10-year data retention increases from 79 °C to 124 °C. And the grain size decreases to dozens of nanometers scale. Based on X-ray photoelectron spectroscopy and transmission electron microscopy results, we knew that nitrogen atoms bond with titanium, forming disorder region at the grain boundary of Sb{sub 3}Te-TiN{sub 2} (STTN). Thus, STTN has a quite different crystallization mechanism from Sb{sub 3}Te. Furthermore, PCM device based on STTN can realize reversible phase change under 20 ns electrical pulse.

  8. MA AP MA MA MA AP AP MA MA MA AP AP

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AP MA MA MA AP AP MA MA MA AP AP low low low AP MA Run PAMM / AP Low alpha University Holidays AP/PAMM Spear Down Hrs S 30 31 S 30 5260 832 6092 2013 2014 Scheduled Hours Users Total 29 31 30 29 31 30 F 31 28 29 30 T 31 28 27 29 28 30 30 27 29 W 30 29 26 29 27 31 28 AP T 29 26 29 27 AP PAMM 30 28 25 31 28 26 30 27 30 28 26 M 28 25 29 27 24 30 27 25 29 26 S 27 24 28 26 23 27 29 26 24 28 25 S 26 23 28 26 24 23 27 25 28 28 25 25 22 27 24 25 23 F 25 26 24 21 27 24 22 26 23 22 27 T 24 21 20 24 22 21

  9. Te

    U.S. Energy Information Administration (EIA) Indexed Site

    N u n a v u t O n t a r i o A l b e r t a Te x a s N o r t h w e s t Te r r i t o r i e s ... M o n t a n a U t a h I d a h o C a l i f o r n i a N e v a d a O r e g o n A r i z o n a ...

  10. MA MA AP

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MA AP low low low MA Run PAMM / AP Low alpha University Holidays AP/PAMM Spear Down Oct Nov S Apr May Jun Jul Aug Sep 7/17/2015 SPEAR OPERATING SCHEDULE 2015-2016 2015 2016 Oct Nov Dec Jan Feb Mar S 1 1 2 1 4 1 M 2 1 2 1 T 3 1 3 PAMM 1 2 2 3 6 3 W 4 2 3 AP AP 5 2 1 3 2 4 F 2 6 4 1 5 2 4 3 T 1 5 3 5 2 7 4 3 1 5 4 1 6 4 1 5 8 5 S 4 8 2 6 3 2 7 4 2 6 5 S 3 7 6 5 3 7 6 3 8 6 3 7 4 8 7 M 5 9 7 4 9 10 7 AP PAMM PAMM PAMM PAMM 4 8 5 4 9 6 8 AP 5 9 6 5 AP 10 7 5 9 AP 8 6 10 9 13 W 7 11 9 11 T 6 10 8 12

  11. Te

    U.S. Energy Information Administration (EIA) Indexed Site

    D u N o r d - O u e s t Te r r e - N e u v e - e t - L a b r a d o r Q u b e c l e - d u - P r i n c e - d o u a r d N o u v e l l e - c o s s e N o u v e a u - B r u n ...

  12. Mechanisms of charge transport in anisotype n-TiO{sub 2}/p-CdTe heterojunctions

    SciTech Connect (OSTI)

    Brus, V. V.; Ilashchuk, M. I.; Kovalyuk, Z. D.; Maryanchuk, P. D.; Ulyanytsky, K. S.; Gritsyuk, B. N.

    2011-08-15

    Surface-barrier anisotype n-TiO{sub 2}/p-CdTe heterojunctions are fabricated by depositing thin titanium-dioxide films on a freshly cleaved surface of single-crystalline cadmium-telluride wafers by reactive magnetron sputtering. It is established that the electric current through the heterojunctions under investigation is formed by generation-recombination processes in the space-charge region via a deep energy level and tunneling through the potential barrier. The depth and nature of the impurity centers involved in the charge transport are determined.

  13. Topological crystalline insulator Pb{sub x}Sn{sub 1-x}Te thin films on SrTiO{sub 3} (001) with tunable Fermi levels

    SciTech Connect (OSTI)

    Guo, Hua; Liu, Jun-Wei; Wang, Zhen-Yu; Wu, Rui; Ji, Shuai-Hua; Duan, Wen-Hui; Chen, Xi Xue, Qi-Kun; Yan, Chen-Hui; Zhang, Zhi-Dong; Wang, Li-Li; He, Ke; Ma, Xu-Cun

    2014-05-01

    In this letter, we report a systematic study of topological crystalline insulator Pb{sub x}Sn{sub 1-x}Te (0 < x < 1) thin films grown by molecular beam epitaxy on SrTiO{sub 3}(001). Two domains of Pb{sub x}Sn{sub 1-x}Te thin films with intersecting angle of ? ? 45 were confirmed by reflection high energy diffraction, scanning tunneling microscopy, and angle-resolved photoemission spectroscopy (ARPES). ARPES study of Pb{sub x}Sn{sub 1-x}Te thin films demonstrated that the Fermi level of PbTe could be tuned by altering the temperature of substrate whereas SnTe cannot. An M-shaped valance band structure was observed only in SnTe but PbTe is in a topological trivial state with a large gap. In addition, co-evaporation of SnTe and PbTe results in an equivalent variation of Pb concentration as well as the Fermi level of Pb{sub x}Sn{sub 1-x}Te thin films.

  14. Tammy Ma

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tammy Ma Drawn to Science and Giving Back Tammy Ma Tammy Ma We sat down with Dr. Tammy Ma, an experimental physicist at the National Ignition Facility, to talk about what motivates her, why she loves science, her belief in giving back, and advice for younger scientists. Motivation and work ethic My mother, unfortunately, didn't get the chance to finish high school or go to college because she emigrated to Canada as a teenager. So it's always been instilled in both me and my younger brother that

  15. Ma Philippine

    Office of Scientific and Technical Information (OSTI)

    - . . . . . . . . . . . . . . . - . . . . . . . . . . . . . -. . . . . . . . . . 4 . Na . Ma Philippine 4 I s Sea PHILIPPINES 7 ; : : ' - ,. * . DE89 007772 PHILIPPINES Asia Pacific Energy Series Country Report DISCLAIMER This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsi-

  16. Ookie Ma | Department of Energy

    Energy Savers [EERE]

    Ookie Ma About Us Ookie Ma - Policy and Analysis Portfolio Manager, Office of Energy Efficiency and Renewable Energy Most Recent Natural Gas: Lifting Mileage Higher and Higher ...

  17. MaRIE Presentations

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Challenge of Dynamic Mesoscale Imaging (Conference) | SciTech Connect Conference: MaRIE 1.0: The Matter-Radiation Interactions in Extremes Project, and the Challenge of Dynamic Mesoscale Imaging Citation Details In-Document Search Title: MaRIE 1.0: The Matter-Radiation Interactions in Extremes Project, and the Challenge of Dynamic Mesoscale Imaging The Matter-Radiation Interactions in Extremes project will build the experimental facility for the time-dependent control of dynamic material

  18. Ma_1995.pdf

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    (Technical Report) | SciTech Connect Technical Report: MaRIE: A facility for time-dependent materials science at the mesoscale Citation Details In-Document Search Title: MaRIE: A facility for time-dependent materials science at the mesoscale Authors: Barnes, Cris William [1] ; Kippen, Karen Elizabeth [1] + Show Author Affiliations Los Alamos National Laboratory Publication Date: 2015-02-11 OSTI Identifier: 1170260 Report Number(s): LA-UR-15-20995 DOE Contract Number: AC52-06NA25396 Resource

  19. DOE/MA-0518

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MA-0518 Origins of the Nevada Test Site United States Department of Energy Terrence R. Fehner F. G. Gosling History Division Executive Secretariat Management and Administration Department of Energy December 2000 Acknowledgments Origins of the Nevada Test Site was written in conjunction with the 50th anniversary commemoration of the Nevada Test Site. The history was released at the official celebration held in Las Vegas, Nevada, on December 18, 2000, fifty years after President Harry S. Truman

  20. US NE MA Site Consumption

    U.S. Energy Information Administration (EIA) Indexed Site

    NE MA Site Consumption million Btu $0 $500 $1,000 $1,500 $2,000 $2,500 $3,000 US NE MA Expenditures dollars ALL ENERGY average per household (excl. transportation) 0 2,000 4,000 6,000 8,000 10,000 12,000 US NE MA Site Consumption kilowatthours $0 $250 $500 $750 $1,000 $1,250 $1,500 US NE MA Expenditures dollars ELECTRICITY ONLY average per household * Massachusetts households use 109 million Btu of energy per home, 22% more than the U.S. average. * The higher than average site consumption

  1. CAES MaCS Home

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    cross-cutting capabilities that support the Center for Advanced Energy Studies' (CAES) mission in multiple initiative areas. MaCS is largely made possible through its...

  2. MA Mortenson | Open Energy Information

    Open Energy Info (EERE)

    Name: MA Mortenson Place: Minnesota Zip: 55440-0710 Sector: Solar, Wind energy Product: Construction and building firm active in the installation of wind and solar farms....

  3. Discovery and utilization of sorghum genes (Ma5/Ma6)

    DOE Patents [OSTI]

    Mullet, John E; Rooney, William L; Klein, Patricia E; Morishige, Daryl; Murphy, Rebecca; Brady, Jeff A

    2012-11-13

    Methods and composition for the production of non-flowering or late flowering sorghum hybrid. For example, in certain aspects methods for use of molecular markers that constitute the Ma5/Ma6 pathway to modulate photoperiod sensitivity are described. The invention allows the production of plants having improved productivity and biomass generation.

  4. DOE - Office of Legacy Management -- Beverly MA Site - MA 04

    Office of Legacy Management (LM)

    This site is managed by the U.S. Department of Energy Office of Legacy Management. MA.04-1 - DOE Memorandum; Voigt to LaGrone; Subject: Designation of Sites for Remedial Action - ...

  5. MA Org Chart, November 16, 2015

    Broader source: Energy.gov (indexed) [DOE]

    of Staff MA-80 Office of the Ombudsman Rita R. Franklin, Director November 2015 Adrian Collins, Dep. Director MA-50 Office of Asset Management Carmelo Melendez, Director MA-40...

  6. MA Org Chart, August 13, 2015

    Broader source: Energy.gov (indexed) [DOE]

    of Staff MA-80 Office of the Ombudsman Rita R. Franklin, Director August 2015 Adrian Collins, Dep. Director MA-50 Office of Asset Management Carmelo Melendez, Director MA-40...

  7. MA Org Chart, March 22, 2016

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Management MA-1 Ingrid Kolb, Director Laurie Morman, Chief of Staff Office of Resource Management and Planning MA-1.1 Marilyn Dillon, Director Sandra Hersh, Dep. Director Office of Scheduling and Advance Charles Quintero, Director MA-10 MA-70 Office of Executive Secretariat Amy B. Demagistris, Deputy Director Office of Policy Analysis Michael Coogan Office of Correspondence Management Steven Johnsen MA-72 Administration, MIS, and Executive Commitments Group Shena Kennerly MA-74 Office of History

  8. MA Org Chart, January 5, 2016

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Director Office of Scheduling and Advance Charles Quintero, Director MA-10 MA-70 Office of ... Information Technology Program Emily Stanton Chris Morris, FOIA Officer Vacant Office of ...

  9. Scaling of X pinches from 1 MA to 6 MA.

    SciTech Connect (OSTI)

    Bland, Simon Nicholas; McBride, Ryan D.; Wenger, David Franklin; Sinars, Daniel Brian; Chittenden, Jeremy Paul; Pikuz, Sergei A.; Harding, Eric; Jennings, Christopher A.; Ampleford, David J.; Yu, Edmund P.; Cuneo, Michael Edward; Shelkovenko, Tatiana A.; Hansen, Stephanie B.

    2010-09-01

    This final report for Project 117863 summarizes progress made toward understanding how X-pinch load designs scale to high currents. The X-pinch load geometry was conceived in 1982 as a method to study the formation and properties of bright x-ray spots in z-pinch plasmas. X-pinch plasmas driven by 0.2 MA currents were found to have source sizes of 1 micron, temperatures >1 keV, lifetimes of 10-100 ps, and densities >0.1 times solid density. These conditions are believed to result from the direct magnetic compression of matter. Physical models that capture the behavior of 0.2 MA X pinches predict more extreme parameters at currents >1 MA. This project developed load designs for up to 6 MA on the SATURN facility and attempted to measure the resulting plasma parameters. Source sizes of 5-8 microns were observed in some cases along with evidence for high temperatures (several keV) and short time durations (<500 ps).

  10. Xuedan Ma | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Xuedan Ma Assistant Scientist Education Ph.D. University of Hamburg Postdoc experience Center for Integrated Nanotechnologies, Sandia National Laboratories, 2015-2016 Center for Integrated Nanotechnologies, Los Alamos National Laboratories, 2012-2015 Research Summary Quantum optics of semiconductor nanomaterials Temperature dependent single molecule/particle optical spectroscopy and imaging Plasmonic and dielectric metamaterials; nanophotonics and nano-optics Biological imaging and sensing;

  11. LAMPF TO MaRIE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    LAMPF TO MaRIE Los Alamos National Laboratory - 70 Years of Science and Beyond E X P E R I M E N T A L P H Y S I C A L S C I E N C E S Through the science of making, measuring, and modeling, the people of Los Alamos National Laboratory discover breakthrough solutions to the most pressing national security challenges. PEOPLE BEHIND THE SCIENCE AND TECHNOLOGY LOS ALAMOS MILESTONES THE EVOLUTION OF LOS ALAMOS SIGNATURE FACILITIES EXPERTISE AND ACHIEVEMENTS IN MAKING, MEASURING, AND MODELING This

  12. Effect of the top electrode materials on the resistive switching characteristics of TiO{sub 2} thin film

    SciTech Connect (OSTI)

    Oh, Sang Chul; Jung, Ho Yong; Lee, Heon

    2011-06-15

    Various metals, such as Pt, stainless steel (SUS), Al, Ni, and Ti, were used as a top electrode (TE) to evaluate the dependency of the resistive switching characteristics on the TE of the metal/TiO{sub 2}/Pt structure. The variation of the chemical composition of TiO{sub 2} in the metal/TiO{sub 2}/Pt structure before and after switching was examined to identify the factors affecting the resistive switching characteristics of the samples with various TE materials. In the case of TE/TiO{sub 2}/Pt structures showing unstable resistive switching behavior, e.g., those with the Al, Ni, and Ti TEs, secondary ion mass spectrometry revealed an increase in the oxygen concentration at the interface area between the TE metal and TiO{sub 2}. This suggests that the oxidation reaction at the interface between the TE metal and TiO{sub 2} might cause the TE/TiO{sub 2}/Pt structure to exhibit unstable resistive switching characteristics. According to these results, the oxidation reaction at the interface between the metal TE and TiO{sub 2} thin film is a primary factor affecting the resistive switching characteristics of TiO{sub 2}-based Resistive Random Access Memory devices.

  13. Johnston LFG (MA RPS Biomass Facility | Open Energy Information

    Open Energy Info (EERE)

    LFG (MA RPS Biomass Facility Jump to: navigation, search Name Johnston LFG (MA RPS Biomass Facility Facility Johnston LFG (MA RPS Sector Biomass Facility Type Landfill Gas Location...

  14. THE EXECUTIVE SECRETARIAT, MA-70 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    THE EXECUTIVE SECRETARIAT, MA-70 THE EXECUTIVE SECRETARIAT, MA-70 Organization chart for the Office of the Executive Secretariat, MA-70 PDF icon Office of the Executive Secretariat ...

  15. MA-60 Org chart | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Updated August 12, 2015 OAM Org Chart (MA-60) v18.pptx More Documents & Publications Office of Management Organization Chart Office of International Affairs Org Chart Policy Flash...

  16. InThrMa | Open Energy Information

    Open Energy Info (EERE)

    Softwaremodeling tools User Interface: Website, Mobile Device Website: www.inthrma.com Web Application Link: www.inthrma.com Cost: Paid Language: English InThrMa Screenshot...

  17. DOE - Office of Legacy Management -- Tracerlab Inc - MA 11

    Office of Legacy Management (LM)

    and cesium blocks during the early 1950s. MA.11-1 MA.11-3 Site Disposition: Eliminated - NRC licensed MA.11-2 MA.11-3 Radioactive Materials Handled: Yes Primary Radioactive...

  18. DOE - Office of Legacy Management -- Shpack Landfill - MA 06

    Office of Legacy Management (LM)

    Shpack Landfill - MA 06 FUSRAP Considered Sites Shpack Landfill, NY Alternate Name(s): Attleboro, MA Metals and Controls Site Norton Landfill area MA.06-2 MA.06-3 Location: 68 Union Road, Norton, Massachusetts MA.06-2 Historical Operations: No AEC activities were conducted on site. Contamination was suspected from disposal of materials containing uranium and zirconium ash. MA.06-2 MA.06-3 Eligibility Determination: Eligible MA.06-1 Radiological Survey(s): Assessment Surveys MA.06-4 MA.06-5

  19. 125Te NMR chemical-shift trends in PbTeGeTe and PbTeSnTe alloys

    SciTech Connect (OSTI)

    Njegic, Bosiljka; Levin, Evgenii M.; Schmidt-Rohr, Klaus

    2013-10-08

    Complex tellurides, such as doped PbTe, GeTe, and their alloys, are among the best thermoelectric materials. Knowledge of the change in 125Te NMR chemical shift due to bonding to dopant or solute atoms is useful for determination of phase composition, peak assignment, and analysis of local bonding. We have measured the 125Te NMR chemical shifts in PbTe-based alloys, Pb1?xGexTe and Pb1?xSnxTe, which have a rocksalt-like structure, and analyzed their trends. For low x, several peaks are resolved in the 22-kHz MAS 125Te NMR spectra. A simple linear trend in chemical shifts with the number of Pb neighbors is observed. No evidence of a proposed ferroelectric displacement of Ge atoms in a cubic PbTe matrix is detected at low Ge concentrations. The observed chemical shift trends are compared with the results of DFT calculations, which confirm the linear dependence on the composition of the first-neighbor shell. The data enable determination of the composition of various phases in multiphase telluride materials. They also provide estimates of the 125Te chemical shifts of GeTe and SnTe (+970 and +400150 ppm, respectively, from PbTe), which are otherwise difficult to access due to Knight shifts of many hundreds of ppm in neat GeTe and SnTe.

  20. DOE - Office of Legacy Management -- National Fireworks Ordnance Corp - MA

    Office of Legacy Management (LM)

    13 Fireworks Ordnance Corp - MA 13 FUSRAP Considered Sites Site: NATIONAL FIREWORKS ORDNANCE CORP (MA.13) Eliminated from consideration under FUSRAP Designated Name: Not Designated Alternate Name: American Potash and Chemical Corporation MA.13-3 Location: West Hanover , Massachusetts MA.13-1 Evaluation Year: 1991 MA.13-1 Site Operations: Performed bench scale research and development on uranium forming during the 1960s. MA.13-2 MA.13-3 Site Disposition: Eliminated - Potential for

  1. DOE - Office of Legacy Management -- Heald Machine Co - MA 15

    Office of Legacy Management (LM)

    Location: Worcester , Massachusetts MA.15-1 Evaluation Year: 1994 MA.15-2 MA.15-3 Site Operations: Research and development on uranium slug drilling machines in the early 1960s. ...

  2. DOE - Office of Legacy Management -- Norton Co - MA 12

    Office of Legacy Management (LM)

    MA.12-3 Site Operations: Manufactured refractory products using thorium and uranium metal. ... Radioactive Materials Handled: Uranium, Thorium MA.12-4 MA.12-5 Radiological Survey(s): ...

  3. PARS II Enhancements - Igor Pedan, MA-63 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Enhancements - Igor Pedan, MA-63 PARS II Enhancements - Igor Pedan, MA-63 2014 DOE Project Management Workshop PDF icon 28PedanPARSII Enhancements.pdf More Documents & ...

  4. El Ma Electronic Machining srl | Open Energy Information

    Open Energy Info (EERE)

    Ma Electronic Machining srl Jump to: navigation, search Name: El.Ma. Electronic Machining srl Place: Riva del Garda (TN), Italy Zip: 38066 Sector: Hydro, Hydrogen, Solar, Wind...

  5. MaRIE: An experimental facility concept revolutionizing materials...

    Office of Scientific and Technical Information (OSTI)

    MaRIE: An experimental facility concept revolutionizing materials in extremes Citation Details In-Document Search Title: MaRIE: An experimental facility concept revolutionizing...

  6. MaRIE theory, modeling and computation roadmap executive summary...

    Office of Scientific and Technical Information (OSTI)

    Conference: MaRIE theory, modeling and computation roadmap executive summary Citation Details In-Document Search Title: MaRIE theory, modeling and computation roadmap executive ...

  7. DOE - Office of Legacy Management -- Englehard Industries - MA...

    Office of Legacy Management (LM)

    operations - uranium metal - under AEC license. MA.0-03-1 Site Disposition: Eliminated - NRC licensed MA.0-03-1 Radioactive Materials Handled: Yes Primary Radioactive Materials...

  8. MaRIE Undulator & XFEL Systems

    SciTech Connect (OSTI)

    Nguyen, Dinh Cong; Marksteiner, Quinn R.; Anisimov, Petr Mikhaylovich; Buechler, Cynthia Eileen

    2015-03-23

    The 22 slides in this presentation treat the subject under the following headings: MaRIE XFEL Performance Parameters, Input Electron Beam Parameters, Undulator Design, Genesis Simulations, Risks, and Summary It is concluded that time-dependent Genesis simulations show the MaRIE XFEL can deliver the number of photons within the required bandwidth, provided a number of assumptions are met; the highest risks are associated with the electron beam driving the XFEL undulator; and risks associated with the undulator and/or distributed seeding technique may be evaluated or retired by performing early validation experiments.

  9. UCRL-MA-110662 PT I U

    Office of Scientific and Technical Information (OSTI)

    MA-110662 PT I U b EQ3/6, A Software Package for Geochemical Modeling of Aqueous Systems: Package Overview and Installation Guide (Version 7.0) . Thomas J. Wolery September 14,1992 DISCLAIMER This document wasprepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor the University of California nor any of their employees, makes any warranty, express or implied, or assumes any legal liabdity or responsibility for the accuracy,

  10. SE-MA-NO Electric Coop | Open Energy Information

    Open Energy Info (EERE)

    SE-MA-NO Electric Coop Jump to: navigation, search Name: SE-MA-NO Electric Coop Place: Missouri Phone Number: (417) 924-3291 Website: www.semano.com Facebook: https:...

  11. DOE - Office of Legacy Management -- Watertown Arsenal - MA 02

    Office of Legacy Management (LM)

    to Jascewsky; M.I.T. Contract Information October 18, 1976 MA.02-5 - DOE Memorandum; Wilson to Bearse; Samples of Chattanooga Shale for M.I.T.; August 26, 1949 MA.02-6 - DOE ...

  12. DOE - Office of Legacy Management -- Woburn Landfill - MA 07

    Office of Legacy Management (LM)

    Operations: The National Lead Company, Inc. disposed of approximately fifty 55-gallon drums of low grade uranium ore in at this site in 1960. MA.07-2 MA.07-4 Site Disposition:...

  13. Office of Information Resources (MA-90) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Resources (MA-90) Office of Information Resources (MA-90) Freedom of Information 2007 Annual Report PDF icon Office of Information Resources (MA-90) More Documents & Publications ANNUAL FOIA REPORT FOR 2009 U.S. Department of Energy 2008 Annual FOIA Report Microsoft Word - 2005 FOIA ANNUAL REPORT.doc

  14. Identification and characterization of novel NuMA isoforms

    SciTech Connect (OSTI)

    Wu, Jin; Xu, Zhe; He, Dacheng; Lu, Guanting

    2014-11-21

    Highlights: Seven NuMA isoforms generated by alternative splicing were categorized into 3 groups: long, middle and short. Both exons 15 and 16 in long NuMA were hotspot for alternative splicing. Lower expression of short NuMA was observed in cancer cells compared with nonneoplastic controls. Distinct localization pattern of short isoforms indicated different function from that of long and middle NuMA. - Abstract: The large nuclear mitotic apparatus (NuMA) has been investigated for over 30 years with functions related to the formation and maintenance of mitotic spindle poles during mitosis. However, the existence and functions of NuMA isoforms generated by alternative splicing remains unclear. In the present work, we show that at least seven NuMA isoforms (categorized into long, middle and short groups) generated by alternative splicing from a common NuMA mRNA precursor were discovered in HeLa cells and these isoforms differ mainly at the carboxyl terminus and the coiled-coil domains. Two hotspot exons with molecular mass of 3366-nt and 42-nt tend to be spliced during alternative splicing in long and middle groups. Furthermore, full-length coding sequences of long and middle NuMA obtained by using fusion PCR were constructed into GFP-tagged vector to illustrate their cellular localization. Long NuMA mainly localized in the nucleus with absence from nucleoli during interphase and translocated to the spindle poles in mitosis. Middle NuMA displayed the similar cell cycle-dependent distribution pattern as long NuMA. However, expression of NuMA short isoforms revealed a distinct subcellular localization. Short NuMA were present in the cytosol during the whole cycle, without colocalization with mitotic apparatus. These results have allowed us tentatively to explore a new research direction for NuMAs various functions.

  15. The 300 mA SRF ERL

    SciTech Connect (OSTI)

    Ben-Zvi, Ilan

    2013-11-07

    Energy Recovery Linacs (ERL) are important for a variety of applications, from high-power Free-Electron Lasers (FEL) to polarized-electron polarized-proton colliders. The ERL current is arguably the most important characteristic of ERLs for such applications. With that in mind, the Collider-Accelerator Department at Brookhaven National Laboratory embarked on the development of a 300 mA ERL to serve as an R and D test-bed for high-current ERL technologies. These include high-current, extremely well damped superconducting accelerating cavities, high-current superconducting laser-photocathode electron guns and high quantum-efficiency photocathodes. In this presentation I will cover these ERL related developments.

  16. Radiation Protection Instrument Manual, Revision 1, PNL-MA-562

    SciTech Connect (OSTI)

    Johnson, Michelle Lynn

    2009-09-23

    PNL-MA-562 This manual provides specific information for operating and using portable radiological monitoring instruments available for use on the Hanford Site.

  17. DOE - Office of Legacy Management -- Fenwal Inc - MA 14

    Office of Legacy Management (LM)

    Ashland, Massachusetts, February 1, 1967; February 9, 1968 MA.14-2 - DOE Memorandum; Williams to The File; Subject: Elimination of the Sites from the Formerly Utilized Sites...

  18. EDeMa (Smart Grid Project) | Open Energy Information

    Open Energy Info (EERE)

    Jump to: navigation, search Project Name EDeMa Country Germany Headquarters Location Mlheim, Germany Coordinates 51.427074, 6.886492 Loading map... "minzoom":false,"mapping...

  19. MHK Projects/GCK Technology Merrimack River Amesbury MA US |...

    Open Energy Info (EERE)

    Merrimack River Amesbury MA US < MHK Projects Jump to: navigation, search << Return to the MHK database homepage Loading map... "minzoom":false,"mappingservice":"googlemaps3","typ...

  20. MaRIE: An experimental facility concept revolutionizing materials...

    Office of Scientific and Technical Information (OSTI)

    concept revolutionizing materials in extremes Citation Details In-Document Search Title: MaRIE: An experimental facility concept revolutionizing materials in extremes Authors: ...

  1. ORISE "AK RlDGE lNSTlT"TE FOR SCIENCE AND EDUCATION

    Office of Legacy Management (LM)

    ti,;;; il.,. (' . d ORISE "AK RlDGE lNSTlT"TE FOR SCIENCE AND EDUCATION August 1,200l Robert Atkin U.S. Department of Energy Oak Ridge Operations Office P.O. Box 2001 Oak Ridge, ...

  2. Neutron capture of /sup 122/Te, /sup 123/Te, /sup 124/Te, /sup 125/Te, and /sup 126/Te

    SciTech Connect (OSTI)

    Macklin, R.L.; Winters, R.R.

    1989-07-01

    Isotopically enriched samples of the tellurium isotopes from mass 122 to mass 126 were used to measure neutron capture in the energy range 2.6 keV to 600 keV at the Oak Ridge Electron Linear Accelerator pulsed neutron source. Starting at 2.6 keV, over 200 Breit-Wigner resonances for each isotope were used to describe the capture data. Least-squares adjustment gave parameters and their uncertainties for a total of 1659 resonances. Capture cross sections averaged over Maxwellian neutron distributions with temperatures ranging from kT = 5 keV to kT = 100 keV were derived for comparison with stellar nucleosynthesis calculations. For the three isotopes shielded from the astrophysical r-process, /sup 122/Te, /sup 123/Te and /sup 124/Te at kT = 30 keV the respective values were (280 /plus minus/ 10) mb, (819 /plus minus/ 30) mb and (154 /plus minus/ 6) mb. The corresponding products of cross section and solar system abundance are nearly equal in close agreement with s-process nucleosynthesis calculations. 26 refs., 8 figs., 10 tabs.

  3. TE Connectivity Finds Answers in Tomography

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    TE Connectivity Finds Answers in Tomography TE Connectivity Finds Answers in Tomography Print Thursday, 22 August 2013 10:50 TE Connectivity is a world leader in connectivity-the...

  4. DOE - Office of Legacy Management -- Nuclear Metals Inc - MA...

    Office of Legacy Management (LM)

    (AEC); Subject: Program for Uranium Recovery; October 11, 1956. 2 pages MA.09-3 - DuPont Letter to H. L. Kilburn (AEC); Subject: Research Programs in Support of Savannah ...

  5. Price of Everett, MA Natural Gas LNG Imports from Australia ...

    U.S. Energy Information Administration (EIA) Indexed Site

    Australia (Dollars per Thousand Cubic Feet) Price of Everett, MA Natural Gas LNG Imports from Australia (Dollars per Thousand Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 ...

  6. MaRIE theory, modeling and computation roadmap executive summary...

    Office of Scientific and Technical Information (OSTI)

    executive summary describe in detail for each of these areas the current state of the art, the gaps that exist and the road map to MaRIE and beyond. Here we integrate the...

  7. Market Acceptance of Advanced Automotive Technologies (MA3T) Model

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Acceptance of Advanced Automotive Technologies (MA3T) Model (Oak Ridge National Laboratory) Objectives Forecasts sales of competing vehicle technologies among consumer segments. Analyzes how technology, infrastructure, consumer behavior, and policy affect sales of new technologies and determines the resulting societal, environmental and economic impacts. Key Attributes & Strengths MA3T can be used to investigate the societal benefits, costs, and employment impacts of market transitions

  8. A new 40 MA ranchero explosive pulsed power system

    SciTech Connect (OSTI)

    Goforth, James; Herrera, Dennis; Oona, Hank; Torres, David; Atchison, W L; Colgate, S A; Griego, J R; Guzik, J; Holtkamp, D B; Idzorek, G; Kaul, A; Kirkpatrick, R C; Menikoff, R; Reardon, P T; Reinovsky, R E; Rousculp, C L; Sgro, A G; Tabaka, L J; Tierney, T E; Watt, R G

    2009-01-01

    We are developing a new high explosive pulsed power (HEPP) system based on the 1.4 m long Ranchero generator which was developed in 1999 for driving solid density z-pinch loads. The new application requires approximately 40 MA to implode similar liners, but the liners cannot tolerate the 65 {micro}s, 3 MA current pulse associated with delivering the initial magnetic flux to the 200 nH generator. To circumvent this problem, we have designed a system with an internal start switch and four explosively formed fuse (EFF) opening switches. The integral start switch is installed between the output glide plane and the armature. It functions in the same manner as a standard input crowbar switch when armature motion begins, but initially isolates the load. The circuit is completed during the flux loading phase using post hole convolutes. Each convolute attaches the inner (coaxial) output transmission line to the outside of the outer coax through a penetration of the outer coaxial line. The attachment is made with the conductor of an EFF at each location. The EFFs conduct 0.75 MA each, and are actuated just after the internal start switch connects to the load. EFFs operating at these parameters have been tested in the past. The post hole convolutes must withstand as much as 80 kV at peak dl/dt during the Ranchero load current pulse. We describe the design of this new HEPP system in detail, and give the experimental results available at conference time. In addition, we discuss the work we are doing to test the upper current limits of a single standard size Ranchero module. Calculations have suggested that the generator could function at up to {approx}120 MA, the rule of thumb we follow (1 MA/cm) suggests 90 MA, and simple flux compression calculations, along with the {approx}4 MA seed current available from our capacitor bank, suggests 118 MA is the currently available upper limit.

  9. Dual Phase Li4 Ti5O12TiO2 Nanowire Arrays As Integrated Anodes For High-rate Lithium-ion Batteries

    SciTech Connect (OSTI)

    Liao, Jin; Chabot, Victor; Gu, Meng; Wang, Chong M.; Xiao, Xingcheng; Chen, Zhongwei

    2014-08-19

    Lithium titanate (Li4Ti5O12) is well known as a zero strain material inherently, which provides excellent long cycle stability as a negative electrode for lithium ion batteries. However, the low specific capacity (175 mA h g?1) limits it to power batteries although the low electrical conductivity is another intrinsic issue need to be solved. In this work, we developed a facile hydrothermal and ion-exchange route to synthesize the self-supported dual-phase Li4Ti5O12TiO2 nanowire arrays to further improve its capacity as well as rate capability. The ratio of Li4Ti5O12 to TiO2 in the dual phase Li4Ti5O12TiO2 nanowire is around 2:1. The introduction of TiO2 into Li4Ti5O12 increases the specific capacity. More importantly, by interface design, it creates a dual-phase nanostructure with high grain boundary density that facilitates both electron and Li ion transport. Compared with phase-pure nanowire Li4Ti5O12 and TiO2 nanaowire arrays, the dual-phase nanowire electrode yielded superior rate capability (135.5 at 5 C, 129.4 at 10 C, 120.2 at 20 C and 115.5 mA h g?1 at 30 C). In-situ transmission electron microscope clearly shows the near zero deformation of the dual phase structure, which explains its excellent cycle stability.

  10. DOE - Office of Legacy Management -- Tufts College - MA 0-05

    Office of Legacy Management (LM)

    Tufts College - MA 0-05 FUSRAP Considered Sites Site: TUFTS COLLEGE ( MA.0-05 ) Eliminated from further consideration under FUSRAP Designated Name: Not Designated Alternate Name: None Location: Medford , Massachusetts MA.0-05-1 Evaluation Year: 1987 MA.0-05-1 Site Operations: Research and development using only small quantities of radioactive material. MA.0-05-1 Site Disposition: Eliminated - Potential for contamination considered remote based on limited quantities of material handled MA.0-05-1

  11. Climate Action Champions: Boston, MA | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Boston, MA Climate Action Champions: Boston, MA Boston is the largest city in New England and one of the oldest in the United States. Home to sixty colleges and universities, world-renowned medical facilities, nationally competitive professional sports teams, and thriving music and arts scene, Boston is a cultural hub and leader in innovation. | Photo courtesy of the City of Boston. Boston is the largest city in New England and one of the oldest in the United States. Home to sixty colleges and

  12. Search for new particles decaying to diject in 7 TeV proton-proton collisions at CMS

    SciTech Connect (OSTI)

    Ozturk, Sertac; /Cukurova U.

    2011-03-01

    This thesis presents a measurement of the dijet invariant mass spectrum and search for new particles decaying to dijets at CMS in 7 TeV pp collisions using data corresponding to an integrated luminosity of 2.875 pb{sup -1}. The measured dijet mass distribution is compared to QCD prediction from PYTHIA . It is required the pseudorapidity separation of the two jets to satisfy |Dh| < 1.3 with each jet inside the region of |{eta}| < 2.5. The observed dijet mass spectrum is fitted by a smooth function to search for dijet resonances. Since there is no evidence for dijet resonances, the upper limits at 95% Confidence Level (C.L.) on the resonance cross section are set. These generic cross section limits are compared with theoretical predictions for the cross section for several models of new particles: string resonances, axigluons, colorons, excited quarks, E{sub 6} diquarks, Randall-Sundrum gravitons, W' and Z'. It is excluded at 95% C.L. string resonances in the mass range 0.50 < M(S) < 2.50 TeV, excited quarks in the mass range 0.50 < M(q*) < 1.58 TeV, axigluons and colorons in the mass ranges 0.50 < M(A) < 1.17 TeV and 1.47 < M(A) < 1.52 TeV, and E{sub 6} diquarks in the mass ranges 0.50 < M(D) < 0.58 TeV, 0.97 < M(D) < 1.08 TeV, and 1.45 < M(D) < 1.60 TeV. These exclusions extend previously published limits on all models.

  13. Experimental determination of valence band offset at PbTe/CdTe(111)

    Office of Scientific and Technical Information (OSTI)

    heterojunction interface by x-ray photoelectron spectroscopy (Journal Article) | SciTech Connect Experimental determination of valence band offset at PbTe/CdTe(111) heterojunction interface by x-ray photoelectron spectroscopy Citation Details In-Document Search Title: Experimental determination of valence band offset at PbTe/CdTe(111) heterojunction interface by x-ray photoelectron spectroscopy Lattice-matched PbTe/CdTe(111) heterojunction interfaces were studied using x-ray photoelectron

  14. TE Connectivity Finds Answers in Tomography

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    TE Connectivity Finds Answers in Tomography TE Connectivity Finds Answers in Tomography Print Thursday, 22 August 2013 10:50 TE Connectivity is a world leader in connectivity-the $13 billion global company designs and manufactures more than 500,000 different electronic connectivity products for the automotive, energy, industrial, broadband communications, consumer device, healthcare, aerospace, and defense industries. TE Connectivity has a long-standing commitment to innovation and engineering

  15. TE Connectivity Finds Answers in Tomography

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    TE Connectivity Finds Answers in Tomography TE Connectivity Finds Answers in Tomography Print Thursday, 22 August 2013 10:50 TE Connectivity is a world leader in connectivity-the $13 billion global company designs and manufactures more than 500,000 different electronic connectivity products for the automotive, energy, industrial, broadband communications, consumer device, healthcare, aerospace, and defense industries. TE Connectivity has a long-standing commitment to innovation and engineering

  16. DOE - Office of Legacy Management -- Reed Rolled Thread Co - MA 18

    Office of Legacy Management (LM)

    Reed Rolled Thread Co - MA 18 FUSRAP Considered Sites Site: REED ROLLED THREAD CO. (MA.18 ) Eliminated from consideration under FUSRAP Designated Name: Not Designated Alternate Name: Reed Rolled Thread and Die Co MA.18-1 Location: Worcester , Massachusetts MA.18-3 Evaluation Year: 1990 MA.18-2 MA.18-3 Site Operations: Thread rolling of a test lot of 1500 SRO slugs were planned for this site on September 14 and 15, 1955. There is no indication that the operation was actually conducted at this

  17. MaRIE: Probing Dynamic Processes in Soft Materials Using Advanced...

    Office of Scientific and Technical Information (OSTI)

    MaRIE: Probing Dynamic Processes in Soft Materials Using Advanced Light Sources Citation Details In-Document Search Title: MaRIE: Probing Dynamic Processes in Soft Materials Using ...

  18. MaRIE: Probing Dynamic Processes in Soft Materials Using Advanced...

    Office of Scientific and Technical Information (OSTI)

    Los Alamos National Laboratory has developed a concept for a new research facility, MaRIE: Matter-Radiation Interactions in Extremes. The key motivation for MaRIE is to develop new ...

  19. MaRIE 1.0: The Matter-Radiation Interactions in Extremes Project...

    Office of Scientific and Technical Information (OSTI)

    MaRIE 1.0: The Matter-Radiation Interactions in Extremes Project, and the Challenge of Dynamic Mesoscale Imaging Citation Details In-Document Search Title: MaRIE 1.0: The Matter-Ra...

  20. MaRIE 1.0 -- The Matter-Radiation Interactions in Extremes Project...

    Office of Scientific and Technical Information (OSTI)

    MaRIE 1.0 -- The Matter-Radiation Interactions in Extremes Project: Accelerating Qualification, Certification, and Assessment Citation Details In-Document Search Title: MaRIE 1.0 ...

  1. Roadmap to MaRIE January 2015 (Technical Report) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Roadmap to MaRIE January 2015 Citation Details In-Document Search Title: Roadmap to MaRIE January 2015 You are accessing a document from the Department of Energy's (DOE) SciTech ...

  2. Roadmap to MaRIE November 2015 (Technical Report) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Technical Report: Roadmap to MaRIE November 2015 Citation Details In-Document Search Title: Roadmap to MaRIE November 2015 You are accessing a document from the Department of ...

  3. Roadmap to MaRIE August 2015 (Technical Report) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Roadmap to MaRIE August 2015 Citation Details In-Document Search Title: Roadmap to MaRIE August 2015 You are accessing a document from the Department of Energy's (DOE) SciTech ...

  4. Roadmap to MaRIE May 2015 (Technical Report) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Technical Report: Roadmap to MaRIE May 2015 Citation Details In-Document Search Title: Roadmap to MaRIE May 2015 You are accessing a document from the Department of Energy's ...

  5. Roadmap to MaRIE (Technical Report) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Technical Report: Roadmap to MaRIE Citation Details In-Document Search Title: Roadmap to MaRIE You are accessing a document from the Department of Energy's (DOE) SciTech ...

  6. Roadmap to MaRIE March 2015 (Technical Report) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Technical Report: Roadmap to MaRIE March 2015 Citation Details In-Document Search Title: Roadmap to MaRIE March 2015 You are accessing a document from the Department of Energy's ...

  7. Business System Clause - Berta Schreiber, Dir, Office of Policy (MA-61) |

    Energy Savers [EERE]

    Department of Energy Business System Clause - Berta Schreiber, Dir, Office of Policy (MA-61) Business System Clause - Berta Schreiber, Dir, Office of Policy (MA-61) 2014 DOE Project Management Workshop PDF icon Business System Clause - Berta Schreiber, Dir, Office of Policy (MA-61) More Documents & Publications Agenda Agenda_2015 APM Workshop_Final Acquisition Letter No. AL 2013-11

  8. Science and Technology of the 10-MA Spherical Tori

    SciTech Connect (OSTI)

    Peng, Y-K.M.

    1999-11-14

    The Spherical Torus (ST) configuration has recently emerged as an example of confinement concept innovation that enables attractive steps in the development of fusion energy. The scientific potential for the ST has been indicated by recent encouraging results from START,2 CDX-U, and HIT. The scientific principles for the D-fueled ST will soon be tested by NSTX (National Spherical Torus Experiment3) in the U.S. and MAST (Mega-Amp Spherical Tokamak4) in the U.K. at the level of l-2 MA in plasma current. More recently, interest has grown in the U.S. in the possibility of near-term ST fusion burn devices at the level of 10 MA in plasma current. The missions for these devices would be to test burning plasma performance in a small, pulsed D-T-fueled ST (i.e., DTST) and to develop fusion energy technologies in a small steady state ST-based Volume Neutron Source (VNS). This paper reports the results of analysis of the key science and technology issues for these devices.

  9. HNF-SD-WM-TI-740, Rev. OA

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    84045. HNF-SD-WM-TI-740, Rev. OA Standard Inventories of Chemicals and Radionuclides in Hanford Site Ta nk Wastes M. J. Kupfer, A. L. Boldt, B. A. Higley, K. M. Hodgson, L. W. Shelton, B. C. Simpson, and R. A. Watrous (LMHC); M. 0. LeClair (SAIC); G. 1. Borsheim (BA); R. T. Winward (MA); R. M. Orme (NHC); N. 6. Colton (PNNL); S. 1. Lambert and D. E. Place (SESC); and W. W. SchulZ (W 2 S) Lockheed Martin Hanford Corporation, Richland, WA 99352 U.S. Department of Energy Contract DE-AC06-96RL13200

  10. HNF-SD-WM-TI-740, Rev. OC

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    84047 HNF-SD-WM-TI-740, Rev. OC Standard Inventories of Chemicals and Radionuclides in Hanford Site Tank Wastes M. J. Kupfer, A. L. Boldt, K. N. Hodgson, L. W. Shelton, B. C. Simpson, and R. A. Watrous (LMHC); M. D. LeClair (SAIC); G. 1. Borsheim (BA); R. T. Winward (MA); B. A. Higley and R. M. Orme (NHC); N. G. Colton (PNNL); S. L. Lambert and D. E. Place (Cogema); and W. W. Schulz (112S) Lockheed Martin Hanford Corporation, Richland, WA 99352 U.S. Department of Energy Contract

  11. A=16Al (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    93TI07) (Not observed) See (1986AN07

  12. A=16Mg (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    93TI07) (Not observed) See (1986AN07

  13. A=16Na (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    93TI07) (Not observed) See (1986AN07

  14. A=16Si (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    93TI07) (Not observed) See (1986AN07

  15. A=19Be (1995TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    95TI07) (Not observed) See (1983ANZQ

  16. A=19He (1995TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    95TI07) (Not observed) See (1983ANZQ

  17. A=19Li (1995TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    95TI07) (Not observed) See (1983ANZQ

  18. DOE - Office of Legacy Management -- E B Badger - MA 0-01

    Office of Legacy Management (LM)

    B Badger - MA 0-01 FUSRAP Considered Sites Site: E.B. Badger (MA.0-01 ) Eliminated from further consideration under FUSRAP Designated Name: Not Designated Alternate Name: None Location: 75 Pitts Street , Boston , Massachusetts MA.0-01-1 Evaluation Year: 1987 MA.0-01-2 Site Operations: Construction contractor during the mid-1940s; constructed facility to refine pitchblende ore and produce feed materials at another location. MA.0-01-2 Site Disposition: Eliminated - No indication of radioactive

  19. Recycling of CdTe photovoltaic waste

    DOE Patents [OSTI]

    Goozner, Robert E.; Long, Mark O.; Drinkard, Jr., William F.

    1999-01-01

    A method for extracting and reclaiming metals from scrap CdTe photovoltaic cells and manufacturing waste by leaching the waste with a leaching solution comprising nitric acid and water, skimming any plastic material from the top of the leaching solution, separating the glass substrate from the liquid leachate and electrolyzing the leachate to separate Cd from Te, wherein the Te is deposits onto a cathode while the Cd remains in solution.

  20. Everett, MA Liquefied Natural Gas Total Imports (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Total Imports (Million Cubic Feet) Everett, MA Liquefied Natural Gas Total Imports (Million Cubic Feet) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 2013 2,583 2,728 2014 5,470 3,783 2,334 2,806 2,175 3,311 1,567 2,871 2,505 2,003 2015 7,729 7,623 5,521 1,673 2,557 7,133 8,237 2,563 2,653 1,541 2,452 2016 10,633 8,593 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date:

  1. TE Connectivity Finds Answers in Tomography

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    healthcare, aerospace, and defense industries. TE Connectivity has a long-standing commitment to innovation and engineering excellence. Their products help address challenges...

  2. Te

    U.S. Energy Information Administration (EIA) Indexed Site

    U t a h I d a h o C a l i f o r n i a N e v a d a O r e g o n A r i z o n a I o w a K a n s a s C o l o r a d o W y o m i n g S o n o r a N e w M e x i c o M i n n e s o t a N e b ...

  3. Te

    U.S. Energy Information Administration (EIA) Indexed Site

    ... Incluye tecnologas de almacenamiento de energa, vapor comprado, calor residual no atribuido directamente a una fuente de combustible y combustibles derivados de llantas. ...

  4. Te

    U.S. Energy Information Administration (EIA) Indexed Site

    ... Refining Company Lp 31 Countrymark Cooperative Inc 66 Marathon Petroleum Co Lp 101 Santa Maria Refining Company 136 Western Refining Southwest Inc 32 Cross Oil Refining & ...

  5. CdTe devices and method of manufacturing same

    DOE Patents [OSTI]

    Gessert, Timothy A.; Noufi, Rommel; Dhere, Ramesh G.; Albin, David S.; Barnes, Teresa; Burst, James; Duenow, Joel N.; Reese, Matthew

    2015-09-29

    A method of producing polycrystalline CdTe materials and devices that incorporate the polycrystalline CdTe materials are provided. In particular, a method of producing polycrystalline p-doped CdTe thin films for use in CdTe solar cells in which the CdTe thin films possess enhanced acceptor densities and minority carrier lifetimes, resulting in enhanced efficiency of the solar cells containing the CdTe material are provided.

  6. Development of a Hydronic Rooftop Unit-HyPak-MA

    SciTech Connect (OSTI)

    Eric Lee; Mark Berman

    2009-11-14

    The majority of U.S. commercial floor space is cooled by rooftop HVAC units (RTUs). RTU popularity derives chiefly from their low initial cost and relative ease of service access without disturbing building occupants. Unfortunately, current RTUs are inherently inefficient due to a combination of characteristics that unnecessarily increase cooling loads and energy use. 36% percent of annual U.S. energy, and two-thirds of electricity, is consumed in and by buildings. Commercial buildings consume approximately 4.2 quads of energy each year at a cost of $230 billion per year, with HVAC equipment consuming 1.2 quads of electricity. More than half of all U.S. commercial floor space is cooled by packaged HVAC units, most of which are rooftop units (RTUs). Inefficient RTUs create an estimated 3.5% of U.S. CO{sub 2} emissions, thus contributing significantly to global warming5. Also, RTUs often fail to maintain adequate ventilation air and air filtration, reducing indoor air quality. This is the second HyPak project to be supported by DOE through NETL. The prior project, referred to as HyPak-1 in this report, had two rounds of prototype fabrication and testing as well as computer modeling and market research. The HyPak-1 prototypes demonstrated the high performance capabilities of the HyPak concept, but made it clear that further development was required to reduce heat exchanger cost and improve system reliability before HyPak commercialization can commence. The HyPak-1 prototypes were limited to about 25% ventilation air fraction, limiting performance and marketability. The current project is intended to develop a 'mixed-air' product that is capable of full 0-100% modulation in ventilation air fraction, hence it was referred to as HyPak-MA in the proposal. (For simplicity, the -MA has been dropped when referencing the current project.) The objective of the HyPak Project is to design, develop and test a hydronic RTU that provides a quantum improvement over conventional RTU performance. Our proposal targeted 60% and 50% reduction in electrical energy use by the HyPak RTU for dry and humid climates, respectively, when compared with a conventional unit, and reduction in peak energy consumption of 50% and 33% respectively. In addition to performance targets, our goal is to develop a production-ready design with durability, reliability and maintainability similar to air-cooled packaged equipment, and that can be commercialized immediately following the conclusion of this project.

  7. Microstructural study and densification analysis of hot work tool steel matrix composites reinforced with TiB{sub 2} particles

    SciTech Connect (OSTI)

    Fedrizzi, A.; Pellizzari, M.; Zadra, M.; Marin, E.

    2013-12-15

    Hot work tool steels are characterized by good toughness and high hot hardness but are less wear resistant than other tooling materials, such as high speed steel. Metal matrix composites show improved tribological behavior, but not much work has been done in the field of hot work tool steels. In this paper TiB{sub 2}-reinforced hot work tool steel matrix composites were produced by spark plasma sintering (SPS). Mechanical alloying (MA) was proposed as a suited process to improve the composite microstructure. Density measurements and microstructure confirmed that MA promotes sintering and produces a fine and homogeneous dispersion of reinforcing particles. X-ray diffraction patterns of the sintered composites highlighted the formation of equilibrium Fe{sub 2}B and TiC, as predicted by thermodynamic calculations using Thermo-Calc software. Scanning electron microscopy as well as scanning Kelvin probe force microscopy highlighted the reaction of the steel matrix with TiB{sub 2} particles, showing the formation of a reaction layer at the TiB{sub 2}-steel interface. Phase investigations pointed out that TiB{sub 2} is not chemically stable in steel matrix because of the presence of carbon even during short time SPS. - Highlights: TiB{sub 2} reinforced steel matrix composites were produced by spark plasma sintering. TiB{sub 2} was successfully dispersed in the steel matrix by mechanical alloying. Steel and TiB{sub 2} react during sintering forming equilibrium Fe{sub 2}B and TiC. The new phases were investigated by means of AFM, Volta potential and XRD analyses.

  8. High performance Zintl phase TE materials with embedded nanoparticles...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Zintl phase TE materials with embedded nanoparticles High performance Zintl phase TE materials with embedded nanoparticles Performance of zintl phase thermoelectric ...

  9. Hanford External Dosimetry Technical Basis Manual PNL-MA-842

    SciTech Connect (OSTI)

    Rathbone, Bruce A.

    2005-02-25

    The Hanford External Dosimetry Technical Basis Manual PNL-MA-842 documents the design and implementation of the external dosimetry system used at Hanford. The manual describes the dosimeter design, processing protocols, dose calculation methodology, radiation fields encountered, dosimeter response characteristics, limitations of dosimeter design under field conditions, and makes recommendations for effective use of the dosimeters in the field. The manual describes the technical basis for the dosimetry system in a manner intended to help ensure defensibility of the dose of record at Hanford and to demonstrate compliance with 10 CFR 835, DOELAP, DOE-RL, ORP, PNSO, and Hanford contractor requirements. The dosimetry system is operated by PNNL’s Hanford External Dosimetry Program which provides dosimetry services to all Hanford contractors. The primary users of this manual are DOE and DOE contractors at Hanford using the dosimetry services of PNNL. Development and maintenance of this manual is funded directly by DOE and DOE contractors. Its contents have been reviewed and approved by DOE and DOE contractors at Hanford through the Hanford Personnel Dosimetry Advisory Committee which is chartered and chaired by DOE-RL and serves as means of coordinating dosimetry practices across contractors at Hanford. This manual was established in 1996. Since inception, it has been revised many times and maintained by PNNL as a controlled document with controlled distribution. Rev. 0 marks the first revision to be released through PNNL’s Electronic Records & Information Capture Architecture (ERICA) database.

  10. Model for Analysis of Energy Demand (MAED-2) | Open Energy Information

    Open Energy Info (EERE)

    demand based on medium- to long-term scenarios of socio-economic, technological and demographic developments. " References "MAED 2" Retrieved from "http:en.openei.orgw...

  11. MaRIE: Probing Dynamic Processes in Soft Materials Using Advanced Light

    Office of Scientific and Technical Information (OSTI)

    Sources (Technical Report) | SciTech Connect MaRIE: Probing Dynamic Processes in Soft Materials Using Advanced Light Sources Citation Details In-Document Search Title: MaRIE: Probing Dynamic Processes in Soft Materials Using Advanced Light Sources Los Alamos National Laboratory has developed a concept for a new research facility, MaRIE: Matter-Radiation Interactions in Extremes. The key motivation for MaRIE is to develop new experimental capabilities needed to fill the existing gaps in our

  12. A rational minor actinide (MA) recycling concept based on innovative oxide fuel with high AM content

    SciTech Connect (OSTI)

    Tanaka, Kenya; Sato, Isamu; Ishii, Tetsuya; Yoshimochi, Hiroshi; Asaga, Takeo; Kurosaki, Ken

    2007-07-01

    A rational MA recycle concept based on high Am content fuel has been proposed. A design study of an Am- MOX fabrication plant, which is a key facility for the MA recycle concept, has been done and the facility concept was clarified from the viewpoint of basic process viability. Preliminary cost estimation suggested that the total construction cost of the MA recycle facilities including Am-MOX, Np-MOX and MA recovery could be comparable with that of the large scale LWR-MOX fabrication plant required for plutonium in LWR fuel cycle. (authors)

  13. EDeMa (Smart Grid Project) (Krefeld, Germany) | Open Energy Informatio...

    Open Energy Info (EERE)

    (Krefeld, Germany) Jump to: navigation, search Project Name EDeMa Country Germany Headquarters Location Krefeld, Germany Coordinates 50.652943, 6.339111 Loading map......

  14. 2.8-Ma Ash-Flow Caldera At Chegem River In The Northern Caucasus...

    Open Energy Info (EERE)

    .8-Ma Ash-Flow Caldera At Chegem River In The Northern Caucasus Mountains (Russia), Contemporaneous Granites, And Associated Ore Deposits Jump to: navigation, search OpenEI...

  15. DOE - Office of Legacy Management -- C G Sargent and Sons - MA...

    Office of Legacy Management (LM)

    Site Operations: Conducted extruder and drying tests with thorium in the late 1960s. ... Primary Radioactive Materials Handled: Thorium MA.17-3 Radiological Survey(s): Yes - ...

  16. Hanford External Dosimetry Technical Basis Manual PNL-MA-842

    SciTech Connect (OSTI)

    Rathbone, Bruce A.

    2009-08-28

    The Hanford External Dosimetry Technical Basis Manual PNL-MA-842 documents the design and implementation of the external dosimetry system used at Hanford. The manual describes the dosimeter design, processing protocols, dose calculation methodology, radiation fields encountered, dosimeter response characteristics, limitations of dosimeter design under field conditions, and makes recommendations for effective use of the dosimeters in the field. The manual describes the technical basis for the dosimetry system in a manner intended to help ensure defensibility of the dose of record at Hanford and to demonstrate compliance with 10 CFR 835, DOELAP, DOE-RL, ORP, PNSO, and Hanford contractor requirements. The dosimetry system is operated by PNNL’s Hanford External Dosimetry Program (HEDP) which provides dosimetry services to all Hanford contractors. The primary users of this manual are DOE and DOE contractors at Hanford using the dosimetry services of PNNL. Development and maintenance of this manual is funded directly by DOE and DOE contractors. Its contents have been reviewed and approved by DOE and DOE contractors at Hanford through the Hanford Personnel Dosimetry Advisory Committee (HPDAC) which is chartered and chaired by DOE-RL and serves as means of coordinating dosimetry practices across contractors at Hanford. This manual was established in 1996. Since inception, it has been revised many times and maintained by PNNL as a controlled document with controlled distribution. The first revision to be released through PNNL’s Electronic Records & Information Capture Architecture (ERICA) database was designated Revision 0. Revision numbers that are whole numbers reflect major revisions typically involving changes to all chapters in the document. Revision numbers that include a decimal fraction reflect minor revisions, usually restricted to selected chapters or selected pages in the document.

  17. Recycling of CdTe photovoltaic waste

    DOE Patents [OSTI]

    Goozner, Robert E.; Long, Mark O.; Drinkard, Jr., William F.

    1999-04-27

    A method for extracting and reclaiming metals from scrap CdTe photovoltaic cells and manufacturing waste by leaching the metals in dilute nitric acid, leaching the waste with a leaching solution comprising nitric acid and water, skimming any plastic material from the top of the leaching solution, separating the glass substrate from the liquid leachate, adding a calcium containing base to the leachate to precipitate Cd and Te, separating the precipitated Cd and Te from the leachate, and recovering the calcium-containing base.

  18. Recycling of CdTe photovoltaic waste

    DOE Patents [OSTI]

    Goozner, R.E.; Long, M.O.; Drinkard, W.F. Jr.

    1999-04-27

    A method for extracting and reclaiming metals from scrap CdTe photovoltaic cells and manufacturing waste by leaching the metals in dilute nitric acid, leaching the waste with a leaching solution comprising nitric acid and water, skimming any plastic material from the top of the leaching solution, separating the glass substrate from the liquid leachate, adding a calcium containing base to the leachate to precipitate Cd and Te, separating the precipitated Cd and Te from the leachate, and recovering the calcium-containing base. 3 figs.

  19. Effect of mechanical alloying synthesis process on the dielectric properties of (Bi{sub 0.5}Na{sub 0.5}){sub 0.94}Ba{sub 0.06}TiO{sub 3} piezoceramics

    SciTech Connect (OSTI)

    Ghazanfari, Mohammad Reza; Amini, Rasool; Shams, Seyyedeh Fatemeh; Alizadeh, Morteza; Ardakani, Hamed Ahmadi

    2015-08-15

    Highlights: • MA samples show higher dielectric permittivity and Curie temperature. • In MA samples, dielectric loss is almost 27% less than conventional ones. • In MA samples, sintering time and temperature are lower than conventional ones. • In MA samples, particle morphology is more homogeneous conventional ones. • In MA samples, crystallite size is smaller conventional ones. - Abstract: In present work, in order to study the effects of synthesis techniques on dielectric properties, the BNBT lead-free piezoceramics with (Bi{sub 0.5}Na{sub 0.5}){sub 0.94}Ba{sub 0.06}TiO{sub 3} stoichiometry (called as BNBT6) were synthesized by mechanical alloying (MA) and conventional mixed oxides methods. The structural, microstructural, and dielectric properties were carried out by X-ray diffractometer (XRD), scanning electron microscope (SEM), and impedance analyzer LCR meter, respectively. Based on results, the density of MA samples is considerably higher than conventional samples owning to smaller particles size and more uniformity of particle shape of MA samples. Moreover, the dielectric properties of MA samples are comparatively improved in which the dielectric loss of these samples is almost 27% less than conventional ones. Furthermore, MA samples exhibit obviously higher dielectric permittivity and Curie temperature compared to the conventional samples.

  20. Thermodynamic and Transport Properties of YTe3, LaTe3 and CeTe3

    SciTech Connect (OSTI)

    Ru, N.

    2011-08-19

    Measurements of heat capacity, susceptibility, and electrical resistivity are presented for single crystals of the charge density wave compounds YTe{sub 3}, LaTe{sub 3}, and CeTe{sub 3}. The materials are metallic to low temperatures, but have a small density of states due to the charge density wave gapping large portions of the Fermi surface. CeTe{sub 3} is found to be a weak Kondo lattice, with an antiferromagnetic ground state and T{sub N} = 2.8 K. The electrical resistivity of all three compounds is highly anisotropic, confirming the weak dispersion perpendicular to Te planes predicted by band structure calculations.

  1. Hanford External Dosimetry Technical Basis Manual PNL-MA-842

    SciTech Connect (OSTI)

    Rathbone, Bruce A.

    2011-04-04

    The Hanford External Dosimetry Technical Basis Manual PNL-MA-842 documents the design and implementation of the external dosimetry system used at the U.S. Department of Energy (DOE) Hanford site. The manual describes the dosimeter design, processing protocols, dose calculation methodology, radiation fields encountered, dosimeter response characteristics, limitations of dosimeter design under field conditions, and makes recommendations for effective use of the dosimeters in the field. The manual describes the technical basis for the dosimetry system in a manner intended to help ensure defensibility of the dose of record at Hanford and to demonstrate compliance with requirements of 10 CFR 835, the DOE Laboratory Accreditation Program, the DOE Richland Operations Office, DOE Office of River Protection, DOE Pacific Northwest Office of Science, and Hanford’s DOE contractors. The dosimetry system is operated by the Pacific Northwest National Laboratory (PNNL) Hanford External Dosimetry Program which provides dosimetry services to PNNL and all Hanford contractors. The primary users of this manual are DOE and DOE contractors at Hanford using the dosimetry services of PNNL. Development and maintenance of this manual is funded directly by DOE and DOE contractors. Its contents have been reviewed and approved by DOE and DOE contractors at Hanford through the Hanford Personnel Dosimetry Advisory Committee which is chartered and chaired by DOE-RL and serves as means of coordinating dosimetry practices across contractors at Hanford. This manual was established in 1996. Since its inception, it has been revised many times and maintained by PNNL as a controlled document with controlled distribution. The first revision to be released through PNNL’s Electronic Records & Information Capture Architecture database was designated Revision 0. Revision numbers that are whole numbers reflect major revisions typically involving significant changes to all chapters in the document. Revision numbers that include a decimal fraction reflect minor revisions, usually restricted to selected chapters or selected pages in the document. Maintenance and distribution of controlled hard copies of the manual by PNNL was discontinued beginning with Revision 0.2.

  2. Hanford External Dosimetry Technical Basis Manual PNL-MA-842

    SciTech Connect (OSTI)

    Rathbone, Bruce A.

    2007-03-12

    The Hanford External Dosimetry Technical Basis Manual PNL-MA-842 documents the design and implementation of the external dosimetry system used at Hanford. The manual describes the dosimeter design, processing protocols, dose calculation methodology, radiation fields encountered, dosimeter response characteristics, limitations of dosimeter design under field conditions, and makes recommendations for effective use of the dosimeters in the field. The manual describes the technical basis for the dosimetry system in a manner intended to help ensure defensibility of the dose of record at Hanford and to demonstrate compliance with 10 CFR 835, DOELAP, DOE-RL, ORP, PNSO, and Hanford contractor requirements. The dosimetry system is operated by PNNL’s Hanford External Dosimetry Program (HEDP) which provides dosimetry services to all Hanford contractors. The primary users of this manual are DOE and DOE contractors at Hanford using the dosimetry services of PNNL. Development and maintenance of this manual is funded directly by DOE and DOE contractors. Its contents have been reviewed and approved by DOE and DOE contractors at Hanford through the Hanford Personnel Dosimetry Advisory Committee (HPDAC) which is chartered and chaired by DOE-RL and serves as means of coordinating dosimetry practices across contractors at Hanford. This manual was established in 1996. Since inception, it has been revised many times and maintained by PNNL as a controlled document with controlled distribution. Rev. 0 marks the first revision to be released through PNNL’s Electronic Records & Information Capture Architecture (ERICA) database. Revision numbers that are whole numbers reflect major revisions typically involving changes to all chapters in the document. Revision numbers that include a decimal fraction reflect minor revisions, usually restricted to selected chapters or selected pages in the document. Revision Log: Rev. 0 (2/25/2005) Major revision and expansion. Rev. 0.1 (3/12/2007) Minor revision. Updated Chapters 5, 6 and 9 to reflect change in default ring calibration factor used in HEDP dose calculation software. Factor changed from 1.5 to 2.0 beginning January 1, 2007. Pages on which changes were made are as follows: 5.23, 5.69, 5.78, 5.80, 5.82, 6.3, 6.5, 6.29, 9.2.

  3. Hanford External Dosimetry Technical Basis Manual PNL-MA-842

    SciTech Connect (OSTI)

    Rathbone, Bruce A.

    2010-04-01

    The Hanford External Dosimetry Technical Basis Manual PNL-MA-842 documents the design and implementation of the external dosimetry system used at the U.S. Department of Energy (DOE) Hanford site. The manual describes the dosimeter design, processing protocols, dose calculation methodology, radiation fields encountered, dosimeter response characteristics, limitations of dosimeter design under field conditions, and makes recommendations for effective use of the dosimeters in the field. The manual describes the technical basis for the dosimetry system in a manner intended to help ensure defensibility of the dose of record at Hanford and to demonstrate compliance with requirements of 10 CFR 835, the DOE Laboratory Accreditation Program, the DOE Richland Operations Office, DOE Office of River Protection, DOE Pacific Northwest Office of Science, and Hanford’s DOE contractors. The dosimetry system is operated by the Pacific Northwest National Laboratory (PNNL) Hanford External Dosimetry Program which provides dosimetry services to PNNL and all Hanford contractors. The primary users of this manual are DOE and DOE contractors at Hanford using the dosimetry services of PNNL. Development and maintenance of this manual is funded directly by DOE and DOE contractors. Its contents have been reviewed and approved by DOE and DOE contractors at Hanford through the Hanford Personnel Dosimetry Advisory Committee which is chartered and chaired by DOE-RL and serves as means of coordinating dosimetry practices across contractors at Hanford. This manual was established in 1996. Since its inception, it has been revised many times and maintained by PNNL as a controlled document with controlled distribution. The first revision to be released through PNNL’s Electronic Records & Information Capture Architecture database was designated Revision 0. Revision numbers that are whole numbers reflect major revisions typically involving significant changes to all chapters in the document. Revision numbers that include a decimal fraction reflect minor revisions, usually restricted to selected chapters or selected pages in the document. Maintenance and distribution of controlled hard copies of the manual by PNNL was discontinued beginning with Revision 0.2.

  4. GaTe semiconductor for radiation detection

    DOE Patents [OSTI]

    Payne, Stephen A.; Burger, Arnold; Mandal, Krishna C.

    2009-06-23

    GaTe semiconductor is used as a room-temperature radiation detector. GaTe has useful properties for radiation detectors: ideal bandgap, favorable mobilities, low melting point (no evaporation), non-hygroscopic nature, and availability of high-purity starting materials. The detector can be used, e.g., for detection of illicit nuclear weapons and radiological dispersed devices at ports of entry, in cities, and off shore and for determination of medical isotopes present in a patient.

  5. Post-Growth Annealing of Bridgman-grown CdZnTe and CdMnTe Crystals for

    Office of Scientific and Technical Information (OSTI)

    Room-temperature Nuclear Radiation Detectors (Journal Article) | SciTech Connect Post-Growth Annealing of Bridgman-grown CdZnTe and CdMnTe Crystals for Room-temperature Nuclear Radiation Detectors Citation Details In-Document Search Title: Post-Growth Annealing of Bridgman-grown CdZnTe and CdMnTe Crystals for Room-temperature Nuclear Radiation Detectors Bridgman-grown cadmium zinc telluride (CdZnTe or CZT) and cadmium manganese telluride (CdMnTe or CMT) crystals often have Te inclusions that

  6. Hanford External Dosimetry Technical Basis Manual PNL-MA-842

    SciTech Connect (OSTI)

    Rathbone, Bruce A.

    2010-01-01

    The Hanford External Dosimetry Technical Basis Manual PNL-MA-842 documents the design and implementation of the external dosimetry system used at Hanford. The manual describes the dosimeter design, processing protocols, dose calculation methodology, radiation fields encountered, dosimeter response characteristics, limitations of dosimeter design under field conditions, and makes recommendations for effective use of the dosimeters in the field. The manual describes the technical basis for the dosimetry system in a manner intended to help ensure defensibility of the dose of record at Hanford and to demonstrate compliance with 10 CFR 835, DOELAP, DOE-RL, ORP, PNSO, and Hanford contractor requirements. The dosimetry system is operated by PNNL’s Hanford External Dosimetry Program (HEDP) which provides dosimetry services to all Hanford contractors. The primary users of this manual are DOE and DOE contractors at Hanford using the dosimetry services of PNNL. Development and maintenance of this manual is funded directly by DOE and DOE contractors. Its contents have been reviewed and approved by DOE and DOE contractors at Hanford through the Hanford Personnel Dosimetry Advisory Committee (HPDAC) which is chartered and chaired by DOE-RL and serves as means of coordinating dosimetry practices across contractors at Hanford. This manual was established in 1996. Since its inception, it has been revised many times and maintained by PNNL as a controlled document with controlled distribution. The first revision to be released through PNNL’s Electronic Records & Information Capture Architecture (ERICA) database was designated Revision 0. Revision numbers that are whole numbers reflect major revisions typically involving significant changes to all chapters in the document. Revision numbers that include a decimal fraction reflect minor revisions, usually restricted to selected chapters or selected pages in the document. Maintenance and distribution of controlled hard copies of the manual by PNNL was discontinued beginning with Revision 0.2. Revision Log: Rev. 0 (2/25/2005) Major revision and expansion. Rev. 0.1 (3/12/2007) Updated Chapters 5, 6 and 9 to reflect change in default ring calibration factor used in HEDP dose calculation software. Factor changed from 1.5 to 2.0 beginning January 1, 2007. Pages on which changes were made are as follows: 5.23, 5.69, 5.78, 5.80, 5.82, 6.3, 6.5, 6.29, and 9.2. Rev 0.2 (8/28/2009) Updated Chapters 3, 5, 6, 8 and 9. Chapters 6 and 8 were significantly expanded. References in the Preface and Chapters 1, 2, 4, and 7 were updated to reflect updates to DOE documents. Approved by HPDAC on 6/2/2009. Rev 1.0 (1/1/2010) Major revision. Updated all chapters to reflect the Hanford site wide implementation on January 1, 2010 of new DOE requirements for occupational radiation protection. The new requirements are given in the June 8, 2007 amendment to 10 CFR 835 Occupational Radiation Protection (Federal Register, June 8, 2007. Title 10 Part 835. U.S., Code of Federal Regulations, Vol. 72, No. 110, 31904-31941). Revision 1.0 to the manual replaces ICRP 26 dosimetry concepts and terminology with ICRP 60 dosimetry concepts and terminology and replaces external dose conversion factors from ICRP 51 with those from ICRP 74 for use in measurement of operational quantities with dosimeters. Descriptions of dose algorithms and dosimeter response characteristics, and field performance were updated to reflect changes in the neutron quality factors used in the measurement of operational quantities.

  7. QER SECOND INSTALLMENT REGIONAL MEETING--BOSTON, MA | Department of Energy

    Energy Savers [EERE]

    QER SECOND INSTALLMENT REGIONAL MEETING--BOSTON, MA QER SECOND INSTALLMENT REGIONAL MEETING--BOSTON, MA MEETING DATE AND LOCATION Friday, April 15, 2016 Doors open: 8:30 AM; Program begins: 9:30 AM Marriott Long Wharf (Salons D, E, F, L) 296 State Street Boston, MA 02109 Watch the meeting live here. MEETING INFORMATION The U.S. Department of Energy Secretary Ernest Moniz and Dr. John P. Holdren, Director of the White House Office of Science will host a public stakeholder meeting on the second

  8. Efficiency, Cost and Weight Trade-off in TE Power Generation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    TE Materials with Embedded Particles High performance Zintl phase TE materials with embedded nanoparticles High performance Zintl phase TE materials with embedded nanoparticles

  9. MaRIE 1.0: A briefing to Katherine Richardson-McDaniel, Staff...

    Office of Scientific and Technical Information (OSTI)

    Richardson-McDaniel, Staff Member for U. S. Senator Martin Heinrich (D-NM) Citation Details In-Document Search Title: MaRIE 1.0: A briefing to Katherine Richardson-McDaniel, ...

  10. COLLOQUIUM: The MaRIE (Matter-Radiation Interactions in Extremes...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    January 27, 2016, 4:15pm to 5:30pm Colloquia MBG Auditorium COLLOQUIUM: The MaRIE (Matter-Radiation Interactions in Extremes) Project Dr. Cris Barnes Los Alamos National Laboratory...

  11. MaRIE 1.0: The Matter-Radiation Interactions in Extremes Project...

    Office of Scientific and Technical Information (OSTI)

    An x-ray free electron laser at up to 42-keV fundamental energy and with photon pulses down to sub-nanosecond spacing, MaRIE 1.0 is designed to meet the challenges of ...

  12. Desert Peak to Humboldt House and Winnemucca, in: Lane, M.A....

    Open Energy Info (EERE)

    to Humboldt House and Winnemucca, in: Lane, M.A., (ed) Nevada geothermal areas: Desert Peak, Humboldt House, Beoware: Guidebook for field trip Jump to: navigation, search OpenEI...

  13. A=10F (2004TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2004TI06) (Not illustrated) Not observed: see (1979AJ01). See also (1988AJ01

  14. A=10Ne (2004TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2004TI06) (Not illustrated) Not observed: see (1979AJ01). See also (1988AJ01

  15. A=10O (2004TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2004TI06) (Not illustrated) Not observed: see (1979AJ01). See also (1988AJ01

  16. A=17Al (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Al (1993TI07) (Not observed) See (1983ANZQ, 1988WA18, 1992AV03).

  17. A=17He (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    93TI07) (Not illustrated) Not observed: see (1986AJ04, 1988POZS

  18. A=17Li (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    93TI07) (Not illustrated) Not observed: see (1986AJ04, 1988POZS

  19. A=17Mg (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mg (1993TI07) (Not observed) See (1983ANZQ, 1988WA18, 1992AV03).

  20. A=17P (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    93TI07) (Not observed) See (1983ANZQ, 1988WA18, 1992AV03

  1. A=17Si (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Si (1993TI07) (Not observed) See (1983ANZQ, 1988WA18, 1992AV03).

  2. A=18He (1995TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    95TI07) (Not illustrated) Not observed: See (1982AV1A, 1983ANZQ

  3. A=20Al, etc. (1998TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    98TI06) (Not observed) See (1972AJ02, 1983ANZQ, 1986AN07

  4. A=20Be (1998TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    98TI06) (Not observed) See (1977CE05, 1983ANZQ, 1986AN07, 1987SIZX

  5. A=20n (1998TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    98TI06) (Not observed) See (1977CE05, 1983ANZQ, 1986AN07, 1987SIZX

  6. MaRIE 1.0 -- The Matter-Radiation Interactions in Extremes Project:

    Office of Scientific and Technical Information (OSTI)

    Accelerating Qualification, Certification, and Assessment (Technical Report) | SciTech Connect MaRIE 1.0 -- The Matter-Radiation Interactions in Extremes Project: Accelerating Qualification, Certification, and Assessment Citation Details In-Document Search Title: MaRIE 1.0 -- The Matter-Radiation Interactions in Extremes Project: Accelerating Qualification, Certification, and Assessment Authors: Barnes, Cris William [1] + Show Author Affiliations Los Alamos National Laboratory Publication

  7. Determination of CdTe bulk carrier lifetime and interface recombination velocity of CdTe/MgCdTe double heterostructures grown by molecular beam epitaxy

    SciTech Connect (OSTI)

    Zhao, Xin-Hao; Campbell, Calli M.; DiNezza, Michael J.; Liu, Shi; Zhao, Yuan; Zhang, Yong-Hang

    2014-12-22

    The bulk Shockley-Read-Hall carrier lifetime of CdTe and interface recombination velocity at the CdTe/Mg{sub 0.24}Cd{sub 0.76}Te heterointerface are estimated to be around 0.5??s and (4.7??0.4)??10{sup 2?}cm/s, respectively, using time-resolved photoluminescence (PL) measurements. Four CdTe/MgCdTe double heterostructures (DHs) with varying CdTe layer thicknesses were grown on nearly lattice-matched InSb (001) substrates using molecular beam epitaxy. The longest lifetime of 179?ns is observed in the DH with a 2??m thick CdTe layer. It is also shown that the photon recycling effect has a strong influence on the bulk radiative lifetime, and the reabsorption process affects the measured PL spectrum shape and intensity.

  8. Post-Growth Annealing of Bridgman-grown CdZnTe and CdMnTe Crystals...

    Office of Scientific and Technical Information (OSTI)

    temperature gradient, we observed the migration of Te inclusions from a low-temperature ... These results show that the migration, diffusion, and reaction of Te with Cd in the matrix ...

  9. Materials Data on K4(TiTe3)3 (SG:14) by Materials Project

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Kristin Persson

    2015-03-09

    Computed materials data using density functional theory calculations. These calculations determine the electronic structure of bulk materials by solving approximations to the Schrodinger equation. For more information, see https://materialsproject.org/docs/calculations

  10. Effect and optimization of CdS/CdTe interdiffusion on CdTe electrical properties and CdS/CdTe cell performance

    SciTech Connect (OSTI)

    Song, W.; Mao, D.; Kaydanov, V.; Ohno, T.R.; Trefny, J.V.; Levi, D.H.; Johnston, S. McCandless, B.E.

    1999-03-01

    We have investigated the effect of the CdS/CdTe interdiffusion on the properties of the CdTe films and the CdS/CdTe cell performance. Sulfur (S) diffusion into the CdTe films leads to a decreased defect density in the films, improvement of cell performance, and possibly to the increase of the carrier lifetime in the films. Cell performance is improved with the increase of the amount of S in the CdTe films. S diffusion into CdTe also deteriorates the uniformity of the CdS window layers, resulting in worse cell performance. Based on this study, we propose a processing method to improve cell performance. {copyright} {ital 1999 American Institute of Physics.}

  11. MaRIE: A Presentation to the Science Campaigns Round Robin (Conference) |

    Office of Scientific and Technical Information (OSTI)

    SciTech Connect Conference: MaRIE: A Presentation to the Science Campaigns Round Robin Citation Details In-Document Search Title: MaRIE: A Presentation to the Science Campaigns Round Robin Authors: Stevens, Michael Francis [1] ; Barnes, Cris William [1] + Show Author Affiliations Los Alamos National Laboratory Publication Date: 2014-10-14 OSTI Identifier: 1159570 Report Number(s): LA-UR-14-27998 DOE Contract Number: AC52-06NA25396 Resource Type: Conference Resource Relation: Conference: 2014

  12. MaRIE: A facility for time-dependent materials science at the mesoscale

    Office of Scientific and Technical Information (OSTI)

    (Technical Report) | SciTech Connect MaRIE: A facility for time-dependent materials science at the mesoscale Citation Details In-Document Search Title: MaRIE: A facility for time-dependent materials science at the mesoscale Authors: Barnes, Cris William [1] ; Kippen, Karen Elizabeth [1] + Show Author Affiliations Los Alamos National Laboratory Publication Date: 2015-02-11 OSTI Identifier: 1170260 Report Number(s): LA-UR-15-20995 DOE Contract Number: AC52-06NA25396 Resource Type: Technical

  13. EERE Success Story-MA3T Model Application at ORNL Assesses the Future of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fuel Cell Markets | Department of Energy MA3T Model Application at ORNL Assesses the Future of Fuel Cell Markets EERE Success Story-MA3T Model Application at ORNL Assesses the Future of Fuel Cell Markets July 26, 2013 - 12:00am Addthis Leveraging funding from the Fuel Cell Technologies Office, Oak Ridge National Lab (ORNL) has developed a model for simulating the market potential of fuel cell electric vehicles (FCEV) and challenges to achieving success over time, including competition with

  14. Roadmap to MaRIE (Technical Report) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    MaRIE Citation Details In-Document Search Title: Roadmap to MaRIE Authors: Barnes, Cris William [1] + Show Author Affiliations Los Alamos National Laboratory Publication Date: 2014-11-05 OSTI Identifier: 1163634 Report Number(s): LA-UR-14-28624 DOE Contract Number: AC52-06NA25396 Resource Type: Technical Report Research Org: Los Alamos National Laboratory (LANL) Sponsoring Org: DOE/LANL Country of Publication: United States Language: English Subject: Materials Science(36); Nuclear Physics &

  15. Roadmap to MaRIE January 2015 (Technical Report) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    MaRIE January 2015 Citation Details In-Document Search Title: Roadmap to MaRIE January 2015 Authors: Barnes, Cris William [1] + Show Author Affiliations Los Alamos National Laboratory Publication Date: 2015-01-15 OSTI Identifier: 1167483 Report Number(s): LA-UR-15-20265 DOE Contract Number: AC52-06NA25396 Resource Type: Technical Report Research Org: Los Alamos National Laboratory (LANL) Sponsoring Org: DOE/LANL Country of Publication: United States Language: English Subject: Materials

  16. Roadmap to MaRIE November 2015 (Technical Report) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    November 2015 Citation Details In-Document Search Title: Roadmap to MaRIE November 2015 This report describes MaRIE experimental facility in the November 2015 issue of their Science and Technology newsletter. Authors: Barnes, Cris William [1] + Show Author Affiliations Los Alamos National Lab. (LANL), Los Alamos, NM (United States) Publication Date: 2015-11-23 OSTI Identifier: 1226892 Report Number(s): LA-UR--15-29090 DOE Contract Number: AC52-06NA25396 Resource Type: Technical Report Research

  17. New chalcogenide glasses in the CdTe-AgI-As{sub 2}Te{sub 3} system

    SciTech Connect (OSTI)

    Kassem, M.; Le Coq, D.; Boidin, R.; Bychkov, E.; ULCO, LPCA, EA 4493, F-59140 Dunkerque

    2012-02-15

    Highlights: Black-Right-Pointing-Pointer Determination of the glass-forming region in the pseudo-ternary CdTe-AgI-As{sub 2}Te{sub 3} system. Black-Right-Pointing-Pointer Characterization of macroscopic properties of the new CdTe-AgI-As{sub 2}Te{sub 3} glasses. Black-Right-Pointing-Pointer Characterization of the total conductivity of CdTe-AgI-As{sub 2}Te{sub 3} glasses. Black-Right-Pointing-Pointer Comparison between the selenide and telluride equivalent systems. -- Abstract: Chalcogenide glasses in the pseudo-ternary CdTe-AgI-As{sub 2}Te{sub 3} system were synthesized and the glass-forming range was determined. The maximum content of CdTe in this glass system was found to be equal to 15 mol.%. The macroscopic characterizations of samples have consisted in Differential Scanning Calorimetry, density, and X-ray diffraction measurements. The cadmium telluride addition does not generate any significant change in the glass transition temperature but the resistance of binary AgI-As{sub 2}Te{sub 3} glasses towards crystallisation is estimated to be decreasing on the base of {Delta}T = T{sub x} - T{sub g} parameter. The total electrical conductivity {sigma} was measured by complex impedance spectroscopy. First, the CdTe additions in the (AgI){sub 0.5}(As{sub 2}Te{sub 3}){sub 0.5} host glass, (CdTe){sub x}(AgI){sub 0.5-x/2}(As{sub 2}Te{sub 3}){sub 0.5-x/2} lead to a conductivity decrease at x {<=} 0.05. Then, the behaviour is reversed at 0.05 {<=} x {<=} 0.15. The obtained results are discussed by comparison with the equivalent selenide system.

  18. A=20He (1998TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    He (1998TI06) (Not observed) See (1977CE05, 1983ANZQ, 1986AN07, 1987SIZX).

  19. A=20Li (1998TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Li (1998TI06) (Not observed) See (1977CE05, 1983ANZQ, 1986AN07, 1987SIZX).

  20. A=5n (2002TI10)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2002TI10) (Not illustrated) See also the A = 5 introductory discussion titled A = 5 resonance parameters.

  1. MA.2

    Office of Legacy Management (LM)

    C o m m ission in the early years of nuclear energy development to determine whether they need remedial action and whether the Department has authority to perform such action. ...

  2. OVERVIEW OF THE SDSS-IV MaNGA SURVEY: MAPPING NEARBY GALAXIES...

    Office of Scientific and Technical Information (OSTI)

    2000. With a typical integration time of 3 hr, MaNGA reaches a target r-band signal-to-noise ratio of 4-8 (sup -1 per 2'' fiber) at 23 AB mag arcsecsup -2, which is typical...

  3. New compact hohlraum configuration research at the 1.7 MA Z-pinch generator

    SciTech Connect (OSTI)

    Kantsyrev, V. L. Shrestha, I. K.; Esaulov, A. A.; Safronova, A. S.; Shlyaptseva, V. V.; Osborne, G. C.; Astanovitsky, A. L.; Weller, M. E.; Stafford, A.; Schultz, K. A.; Cooper, M. C.; Chuvatin, A. S.; Rudakov, L. I.; Velikovich, A. L.; Cuneo, M. E.; Jones, B.; Vesey, R. A.

    2014-12-15

    A new compact Z-pinch x-ray hohlraum design with parallel-driven x-ray sources was experimentally demonstrated in a full configuration with a central target and tailored shine shields (to provide a symmetric temperature distribution on the target) at the 1.7 MA Zebra generator. This presentation reports on the joint success of two independent lines of research. One of these was the development of new sources – planar wire arrays (PWAs). PWAs turned out to be a prolific radiator. Another success was the drastic improvement in energy efficiency of pulsed-power systems, such as the Load Current Multiplier (LCM). The Zebra/LCM generator almost doubled the plasma load current to 1.7 MA. The two above-mentioned innovative approaches were used in combination to produce a new compact hohlraum design for ICF, as jointly proposed by SNL and UNR. Good agreement between simulated and measured radiation temperature of the central target is shown. Experimental comparison of PWAs with planar foil liners (PFL) - another viable alternative to wire array loads at multi-MA generators show promising data. Results of research at the University of Nevada Reno allowed for the study of hohlraum coupling physics at University-scale generators. The advantages of new hohlraum design applications for multi-MA facilities with W or Au double PWAs or PFL x-ray sources are discussed.

  4. redMaGiC. Selecting Luminous Red Galaxies from the DES Science Verification Data

    SciTech Connect (OSTI)

    Rozo, E.

    2015-07-20

    We introduce redMaGiC, an automated algorithm for selecting Luminous Red Galaxies (LRGs). The algorithm was developed to minimize photometric redshift uncertainties in photometric large-scale structure studies. redMaGiC achieves this by self-training the color-cuts necessary to produce a luminosity-thresholded LRG sam- ple of constant comoving density. Additionally, we demonstrate that redMaGiC photo-zs are very nearly as accurate as the best machine-learning based methods, yet they require minimal spectroscopic training, do not suffer from extrapolation biases, and are very nearly Gaussian. We apply our algorithm to Dark Energy Survey (DES) Science Verification (SV) data to produce a redMaGiC catalog sampling the redshift range z ? [0.2,0.8]. Our fiducial sample has a comoving space density of 10-3 (h-1Mpc)-3, and a median photo-z bias (zspec zphoto) and scatter (?z=(1 + z)) of 0.005 and 0.017 respectively.The corresponding 5? outlier fraction is 1.4%. We also test our algorithm with Sloan Digital Sky Survey (SDSS) Data Release 8 (DR8) and Stripe 82 data, and discuss how spectroscopic training can be used to control photo-z biases at the 0.1% level.

  5. Development of ITER 15 MA ELMy H-mode Inductive Scenario

    SciTech Connect (OSTI)

    Kessel, C. E.; Campbell, D.; Gribov, Y.; Saibene, G.; Ambrosino, G.; Casper, T.; Cavinato, M.; Fujieda, H.; Hawryluk, R.; Horton, L. D.; Kavin, A.; Kharyrutdinov, R.; Koechl, F.; Leuer, J.; Loarte, A.; Lomas, P. J.; Luce, T.; Lukash, V.; Mattei, M.; Nunes, I.; Parail, V.; Polevoi, A.; Portone, A.; Sartori, R.; Sips, A. C.C.; Thomas, P. R.; Welander, A.; Wesley, J.

    2008-10-16

    The poloidal field (PF) coil system on ITER, which provides both feedforward and feedback control of plasma position, shape, and current, is a critical element for achieving mission performance. Analysis of PF capabilities has focused on the 15 MA Q = 10 scenario with a 300-500 s flattop burn phase. The operating space available for the 15 MA ELMy H-mode plasma discharges in ITER and upgrades to the PF coils or associated systems to establish confidence that ITER mission objectives can be reached have been identified. Time dependent self-consistent free-boundary calculations were performed to examine the impact of plasma variability, discharge programming, and plasma disturbances. Based on these calculations a new reference scenario was developed based upon a large bore initial plasma, early divertor transition, low level heating in L-mode, and a late H-mode onset. Equilibrium analyses for this scenario indicate that the original PF coil limitations do not allow low li (<0.8) operation or lower flux states, and the flattop burn durations were predicted to be less than the desired 400 s. This finding motivates the expansion of the operating space, considering several upgrade options to the PF coils. Analysis was also carried out to examine the feedback current reserve required in the CS and PF coils during a series of disturbances and a feasibility assessment of the 17 MA scenario was undertaken. Results of the studies show that the new scenario and modified PF system will allow a wide range of 15 MA 300-500 s operation and more limited but finite 17 MA operation.

  6. Luminosity goals for a 100-TeV pp collider

    SciTech Connect (OSTI)

    Hinchliffe, Ian; Kotwal, Ashutosh; Mangano, Michelangelo L.; Quigg, Chris; Wang, Lian-Tao

    2015-04-23

    We consider diverse examples of science goals that provide a framework to assess luminosity goals for a future 100-TeV proton-proton collider.

  7. Luminosity goals for a 100-TeV pp collider

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Hinchliffe, Ian; Kotwal, Ashutosh; Mangano, Michelangelo L.; Quigg, Chris; Wang, Lian-Tao

    2015-08-20

    We consider diverse examples of science goals that provide a framework to assess luminosity goals for a future 100-TeV proton-proton collider.

  8. High Performance Zintl Phase TE Materials with Embedded Particles...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Presents results from embedding nanoparticles in magnesium silicide alloy matrix ... Zintl Phase Materials with Embedded Nanoparticles High performance Zintl phase TE ...

  9. Structure of Oxide Nanoparticles in Fe-16Cr MA/ODS Ferritic Steel

    SciTech Connect (OSTI)

    Hsiung, L; Fluss, M; Kimura, A

    2010-04-06

    Oxide nanoparticles in Fe-16Cr ODS ferritic steel fabricated by mechanical alloying (MA) method have been examined using high-resolution transmission electron microscopy (HRTEM) techniques. A partial crystallization of oxide nanoparticles was frequently observed in as-fabricated ODS steel. The crystal structure of crystalline oxide particles is identified to be mainly Y{sub 4}Al{sub 2}O{sub 9} (YAM) with a monoclinic structure. Large nanoparticles with a diameter larger than 20 nm tend to be incoherent and have a nearly spherical shape, whereas small nanoparticles with a diameter smaller than 10 nm tend to be coherent or semi-coherent and have faceted boundaries. The oxide nanoparticles become fully crystallized after prolonged annealing at 900 C. These results lead us to propose a three-stage formation mechanism of oxide nanoparticles in MA/ODS steels.

  10. Towards a 100mA Superconducting RF Photoinjector for BERLinPro

    SciTech Connect (OSTI)

    Neumann, Axel; Anders, W.; Burrill, Andrew; Jankowiak, Andreas; Kamps, T.; Knobloch, Jens; Kugeler, Oliver; Lauinger, P.; Matveenko, A.N.; Schmeisser, M.; Volker, J.; Ciovati, Gianluigi; Kneisel, Peter; Nietubyc, R.; Schubert, S.G.; Smedley, John; Sekutowicz, Jacek; Volkov, V.; Will, I.; Zaplatin, Evgeny

    2013-09-01

    For BERLinPro, a 100 mA CW-driven SRF energy recovery linac demonstrator facility, HZB needs to develop a photo-injector superconducting cavity which delivers a at least 1mm*mr emittance beam at high average current. To address these challenges of producing a high peak brightness beam at high repetition rate, at first HZB tested a fully superconducting injector with a lead cathode*,followed now by the design of a SC cavity allowing operation up to 4 mA using CW-modified TTF-III couplers and inserting a normal conducting high quantum efficiency cathode using the HZDR-style insert scheme. This talk will present the latest results and an overview of the measurements with the lead cathode cavity and will describe the design and optimization process, the first production results of the current design and an outlook to the further development steps towards the full power version.

  11. Copper migration in CdTe heterojunction solar cells

    SciTech Connect (OSTI)

    Chou, H.C.; Rohatgi, A.; Jokerst, N.M.; Thomas, E.W.; Kamra, S.

    1996-07-01

    CdTe solar cells were fabricated by depositing a Au/Cu contact with Cu thickness in the range of 50 to 150A on polycrystalline CdTe/CdS/SnO{sub 2} glass structures. The increase in Cu thickness improves ohmic contact and reduces series resistance (R{sub s}), but the excess Cu tends to diffuse into CdTe and lower shunt resistance (R{sub sh}) and cell performance. Light I-V and secondary ion mass spectroscopy (SIMS) measurements were performed to understand the correlations between the Cu contact thickness, the extent of Cu incorporation in the CdTe cells, and its impact on the cell performance. The CdTe/CdS/SnO{sub 2} glass, CdTe/CdS/GaAs, and CdTe/GaAs structures were prepared in an attempt to achieve CdTe films with different degrees of crystallinity and grain size. A large grain polycrystalline CdTe thin film solar cell was obtained for the first time by selective etching the GaAs substrate coupled with the film transfer onto a glass substrate. SIMS measurement showed that poor crystallinity and smaller grain size of the CdTe film promotes Cu diffusion and decreases the cell performance. Therefore, grain boundaries are the main conduits for Cu migration and larger CdTe grain size or alternate method of contact formation can mitigate the adverse effect of Cu and improve the cell performance. 15 refs., 1 fig.,6 tabs.

  12. redMaPPer. I. Algorithm and SDSS DR8 catalog

    SciTech Connect (OSTI)

    Rykoff, E. S.; Rozo, E.; Reddick, R.; Wechsler, R. H.; Busha, M. T.; Cunha, C. E.; Finoguenov, A.; Evrard, A.; Koester, B. P.; Hao, J.; Nord, B.; Leauthaud, A.; Pierre, M.; Sadibekova, T.; Sheldon, E. S.

    2014-04-20

    We describe redMaPPer, a new red sequence cluster finder specifically designed to make optimal use of ongoing and near-future large photometric surveys. The algorithm has multiple attractive features: (1) it can iteratively self-train the red sequence model based on a minimal spectroscopic training sample, an important feature for high-redshift surveys. (2) It can handle complex masks with varying depth. (3) It produces cluster-appropriate random points to enable large-scale structure studies. (4) All clusters are assigned a full redshift probability distribution P(z). (5) Similarly, clusters can have multiple candidate central galaxies, each with corresponding centering probabilities. (6) The algorithm is parallel and numerically efficient: it can run a Dark Energy Survey-like catalog in ?500 CPU hours. (7) The algorithm exhibits excellent photometric redshift performance, the richness estimates are tightly correlated with external mass proxies, and the completeness and purity of the corresponding catalogs are superb. We apply the redMaPPer algorithm to ?10, 000 deg{sup 2} of SDSS DR8 data and present the resulting catalog of ?25,000 clusters over the redshift range z in [0.08, 0.55]. The redMaPPer photometric redshifts are nearly Gaussian, with a scatter ? {sub z} ? 0.006 at z ? 0.1, increasing to ? {sub z} ? 0.02 at z ? 0.5 due to increased photometric noise near the survey limit. The median value for |?z|/(1 + z) for the full sample is 0.006. The incidence of projection effects is low (?5%). Detailed performance comparisons of the redMaPPer DR8 cluster catalog to X-ray and Sunyaev-Zel'dovich catalogs are presented in a companion paper.

  13. DOE Zero Energy Ready Home Case Study 2013: Transformation, Inc., Production House, Devens, MA

    Energy Savers [EERE]

    Production House Devens, MA BUILDING TECHNOLOGIES OFFICE The U.S. Department of Energy invites home builders across the country to meet the extraordinary levels of excellence and quality specified in DOE's Zero Energy Ready Home program (formerly known as Challenge Home). Every DOE Zero Energy Ready Home starts with ENERGY STAR for Homes Version 3 for an energy-efficient home built on a solid foundation of building science research. Advanced technologies are designed in to give you superior

  14. Roadmap to MaRIE May 2015 (Technical Report) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    May 2015 Citation Details In-Document Search Title: Roadmap to MaRIE May 2015 Los Alamos National Laboratory (LANL) hosted the Stewardship Science Academic Programs Symposium, which is designed to foster relationships among young scientists, sponsors and the National Nuclear Security Administration national laboratories. The event highlights much of the work done by prominent scientists and allows attendees to view the multiple on site facilities at LANL. Authors: Barnes, Cris William [1] + Show

  15. DOE Zero Energy Ready Home Case Study: Transformation Inc., Production House, Devens, MA

    Broader source: Energy.gov [DOE]

    Case study of a DOE Zero Energy Ready Home in Devens, MA, that scored HERS 35 without PV or HERS -37 with PV. This 2,508-square-foot custom home has R-46 double-stud walls with open-cell spray foam, a vented attic with R-67 blown cellulose, plus R-10 rigid XPS under the slab, R-20 closed-cell spray foam on basement walls, triple-pane windows, and one mini-split ductless heat pump.

  16. Best Practices Case Study: Rural Development, Inc., Wisdom Way Solar Village, Greenfield, MA

    SciTech Connect (OSTI)

    2010-12-01

    Wisdom Way Solar Village is an appropriate moniker for the 20-unit community of energy-efficient duplexes in Greenfield, MA. The homes meet the requirements of the U.S. Department of Energys Builders Challenge, achieving HERS scores of 8 to 18 by packing energy efficiency features into the compact, heavily insulated homes and adding solar water heating and photovoltaics on top, to net home owners energy cost savings of at least $2,500 per year per home.

  17. An Overview of the MaRIE X-FEL and Electron Radiography LINAC RF Systems

    SciTech Connect (OSTI)

    Bradley, Joseph Thomas III; Rees, Daniel Earl; Scheinker, Alexander; Sheffield, Richard L.

    2015-05-04

    The purpose of the Matter-Radiation Interactions in Extremes (MaRIE) facility at Los Alamos National Laboratory is to investigate the performance limits of materials in extreme environments. The MaRIE facility will utilize a 12 GeV linac to drive an X-ray Free-Electron Laser (FEL). Most of the same linac will also be used to perform electron radiography. The main linac is driven by two shorter linacs; one short linac optimized for X-FEL pulses and one for electron radiography. The RF systems have historically been the one of the largest single component costs of a linac. We will describe the details of the different types of RF systems required by each part of the linacs. Starting with the High Power RF system, we will present our methodology for the choice of RF system peak power and pulselength with respect to klystron parameters, modulator parameters, performance requirements and relative costs. We will also present an overview of the Low Level RF systems that are proposed for MaRIE and briefly describe their use with some proposed control schemes.

  18. High performance Zintl phase TE materials with embedded nanoparticles |

    Broader source: Energy.gov (indexed) [DOE]

    Department of Energy Performance of zintl phase thermoelectric materials with embedded particles are evaluated PDF icon shakouri.pdf More Documents & Publications High performance Zintl phase TE materials with embedded nanoparticles High Performance Zintl Phase TE Materials with Embedded Particles Thermoelectrics Partnership: High Performance Thermoelectric Waste Heat Recovery System Based on Zintl Phase Materials with Embedded Nanoparticles

  19. A=6He (2002TI10)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    E(6He) 151 MeV. DWBA analysis suggests a spectroscopic factor of 1 for the di-neutron cluster. (1998TE1D, 1998TE03). Measurements at Ecm 11.6 and 15.9 MeV (1999RA15) also...

  20. ETA-NAC007 - Control of Measuring and Test Equipment (M&TE)

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Control of Measuring and Test Equipment (M&TE) Prepared by Electric Transportation ... of calibration standards and Measuring and Test Equipment (M&TE) used for measuring, ...

  1. ETA-UAC07 - Control of Measuring and Test Equipment (M&TE)

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    "Control of Measuring and Test Equipment (M&TE)" Prepared by Electric Transportation ... of calibration standards and Measuring and Test Equipment (M&TE) used for measuring, ...

  2. Thermoelectric device including an alloy of GeTe and AgSbTe as the P-type element

    DOE Patents [OSTI]

    Skrabek, Emanuel Andrew; Trimmer, Donald Smith

    1976-01-01

    Improved alloys suitable for thermoelectric applications and having the general formula: (AgSbTe.sub.2).sub.1.sub.-x + (GeTe).sub.x wherein x has a value of about 0.80 and 0.85, have been found to possess unexpectedly high thermoelectric properties such as efficiency index, as well as other improved physical properties.

  3. On the possibility of neutron generation in an imploding TiD{sub 2} puff Z pinch

    SciTech Connect (OSTI)

    Baksht, Rina B.; Tel-Aviv University, Tel Aviv ; Oreshkin, Vladimir I.; Tomsk Polytechnic University, Tomsk ; Rousskikh, Alexander G.

    2013-08-15

    Simulation of implosion of a TiD{sub 2} puff Z pinch is reported. The Z pinch is supposed to be produced by the plasma flow generated by a vacuum arc, as described by Rousskikh et al.[Phys. Plasmas 18, 092707 (2011)]. To simulate the implosion, a one-dimensional two-temperature radiative magnetohydrodynamics code was used. The simulation has shown that neutrons are generated during the implosion of a TiD{sub 2} puff Z pinch due to thermalization of the pinch plasma stagnated on axis. It has been shown that the necessary condition for neutron generation is that the ion temperature must be substantially higher than the electron temperature. For a pinch current of 1 MA, the predicted yield of 'thermal' neutrons is 2.5 10{sup 9} neutrons/shot.

  4. Multiband Te p Based Superconductivity of Ta4Pd3Te16

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Singh, David J.

    2014-10-06

    We recently discovered that Ta4Pd3Te16 is a superconductor that has been suggested to be an unconventional superconductor near magnetism. Here, we report electronic structure calculations showing that despite the layered crystal structure the material is an anisotropic three-dimensional (3D) metal. The Fermi surface contains prominent one-dimensional (1D) and two-dimensional (2D) features, including nested 1D sheets, a 2D cylindrical section, and a 3D sheet. Moreover, the electronic states that make up the Fermi surface are mostly derived from Te p states with small Ta d and Pd d contributions. This places the compound far from magnetic instabilities. The results are discussedmore » in terms of multiband superconductivity.« less

  5. A=16Li (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Li (1993TI07) (Not illustrated) This nucleus has not been observed. Shell model studies (1988POZS) are used to predict J and the magnetic dipole moment....

  6. A=16He (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    93TI07) (Not illustrated) This nucleus has not been observed. See (1982AV1A, 1983ANZQ, 1986AJ04

  7. A=19Mg (1995TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mg (1995TI07) (Not observed) See (1987AJ02) and (1987GU1K, 1987PO01, 1993HI08

  8. OVERVIEW OF THE SDSS-IV MaNGA SURVEY: MAPPING NEARBY GALAXIES AT APACHE POINT OBSERVATORY

    SciTech Connect (OSTI)

    Bundy, Kevin; Bershady, Matthew A.; Wake, David A.; Tremonti, Christy; Diamond-Stanic, Aleksandar M.; Law, David R.; Cherinka, Brian; Yan, Renbin; Snchez-Gallego, Jos R.; Drory, Niv; MacDonald, Nicholas; Weijmans, Anne-Marie; Thomas, Daniel; Masters, Karen; Coccato, Lodovico; Aragn-Salamanca, Alfonso; Avila-Reese, Vladimir; Badenes, Carles; Falcn-Barroso, Jsus; Belfiore, Francesco; and others

    2015-01-01

    We present an overview of a new integral field spectroscopic survey called MaNGA (Mapping Nearby Galaxies at Apache Point Observatory), one of three core programs in the fourth-generation Sloan Digital Sky Survey (SDSS-IV) that began on 2014 July 1. MaNGA will investigate the internal kinematic structure and composition of gas and stars in an unprecedented sample of 10,000 nearby galaxies. We summarize essential characteristics of the instrument and survey design in the context of MaNGA's key science goals and present prototype observations to demonstrate MaNGA's scientific potential. MaNGA employs dithered observations with 17 fiber-bundle integral field units that vary in diameter from 12'' (19 fibers) to 32'' (127 fibers). Two dual-channel spectrographs provide simultaneous wavelength coverage over 3600-10300 at R ? 2000. With a typical integration time of 3 hr, MaNGA reaches a target r-band signal-to-noise ratio of 4-8 ({sup 1} per 2'' fiber) at 23 AB mag arcsec{sup 2}, which is typical for the outskirts of MaNGA galaxies. Targets are selected with M {sub *} ? 10{sup 9} M {sub ?} using SDSS-I redshifts and i-band luminosity to achieve uniform radial coverage in terms of the effective radius, an approximately flat distribution in stellar mass, and a sample spanning a wide range of environments. Analysis of our prototype observations demonstrates MaNGA's ability to probe gas ionization, shed light on recent star formation and quenching, enable dynamical modeling, decompose constituent components, and map the composition of stellar populations. MaNGA's spatially resolved spectra will enable an unprecedented study of the astrophysics of nearby galaxies in the coming 6yr.

  9. Use of separate ZnTe interface layers to form ohmic contacts to p-CdTe films

    DOE Patents [OSTI]

    Gessert, T.A.

    1999-06-01

    A method of is disclosed improving electrical contact to a thin film of a p-type tellurium-containing II-VI semiconductor comprising: depositing a first undoped layer of ZnTe on a thin film of p-type tellurium containing II-VI semiconductor with material properties selected to limit the formation of potential barriers at the interface between the p-CdTe and the undoped layer, to a thickness sufficient to control diffusion of the metallic-doped ZnTe into the p-type tellurium-containing II-VI semiconductor, but thin enough to minimize affects of series resistance; depositing a second heavy doped p-type ZnTe layer to the first layer using an appropriate dopant; and depositing an appropriate metal onto the outer-most surface of the doped ZnTe layer for connecting an external electrical conductor to an ohmic contact. 11 figs.

  10. Use of separate ZnTe interface layers to form OHMIC contacts to p-CdTe films

    DOE Patents [OSTI]

    Gessert, Timothy A.

    1999-01-01

    A method of improving electrical contact to a thin film of a p-type tellurium-containing II-VI semiconductor comprising: depositing a first undoped layer of ZnTe on a thin film of p-type tellurium containing II-VI semiconductor with material properties selected to limit the formation of potential barriers at the interface between the p-CdTe and the undoped layer, to a thickness sufficient to control diffusion of the metallic-doped ZnTe into the p-type tellurim-containing II-VI semiconductor, but thin enough to minimize affects of series resistance; depositing a second heavy doped p-type ZnTe layer to the first layer using an appropriate dopant; and depositing an appropriate metal onto the outer-most surface of the doped ZnTe layer for connecting an external electrical conductor to an ohmic contact.

  11. MaRIE 1.0: A briefing to Katherine Richardson-McDaniel, Staff Member for U.

    Office of Scientific and Technical Information (OSTI)

    S. Senator Martin Heinrich (D-NM) (Technical Report) | SciTech Connect MaRIE 1.0: A briefing to Katherine Richardson-McDaniel, Staff Member for U. S. Senator Martin Heinrich (D-NM) Citation Details In-Document Search Title: MaRIE 1.0: A briefing to Katherine Richardson-McDaniel, Staff Member for U. S. Senator Martin Heinrich (D-NM) At the request of Katherine Richardson-McDaniel, Staff Member to U.S. Senator Martin Heinrich (D-NM), a high-level briefing was requested about MaRIE 1.0, the

  12. Hard X-ray emission and {sup 44}Ti line features of the Tycho supernova remnant

    SciTech Connect (OSTI)

    Wang, Wei [National Astronomical Observatories, Chinese Academy of Sciences, 20A Datun Road, Chaoyang District, Beijing 100012 (China); Li, Zhuo, E-mail: wangwei@bao.ac.cn, E-mail: zhuo.li@pku.edu.cn [Department of Astronomy and Kavli Institute for Astronomy and Astrophysics, Peking University, Beijing 100871 (China)

    2014-07-10

    A deep hard X-ray survey of the International Gamma-Ray Astrophysics Laboratory (INTEGRAL) satellite has detected for the first time non-thermal emission up to 90 keV in the Tycho supernova (SN) remnant. Its 3-100 keV spectrum is fitted with a thermal bremsstrahlung of kT ? 0.81 0.45 keV plus a power-law model of ? ? 3.01 0.16. Based on diffusive shock acceleration theory, this non-thermal emission, together with radio measurements, implies that the Tycho remnant may not accelerate protons up to >PeV but to hundreds TeV. Only heavier nuclei may be accelerated to the cosmic ray spectral 'knee'. In addition, using INTEGRAL, we search for soft gamma-ray lines at 67.9 and 78.4 keV that come from the decay of radioactive {sup 44}Ti in the Tycho remnant. A bump feature in the 60-90 keV energy band, potentially associated with the {sup 44}Ti line emission, is found with a marginal significance level of ?2.6?. The corresponding 3? upper limit on the {sup 44}Ti line flux amounts to 1.5 10{sup 5} photon cm{sup 2} s{sup 1}. Implications on the progenitor of the Tycho SN, considered to be a Type Ia SN prototype, are discussed.

  13. Electrochemically deposited BiTe-based nanowires for thermoelectric applications

    SciTech Connect (OSTI)

    Ng, Inn-Khuan; Kok, Kuan-Ying; Rahman, Che Zuraini Che Ab; Saidin, Nur Ubaidah; Ilias, Suhaila Hani; Choo, Thye-Foo

    2014-02-12

    Nanostructured materials systems such as thin-films and nanowires (NWs) are promising for thermoelectric power generation and refrigeration compared to traditional counterparts in bulk, due to their enhanced thermoelectric figures-of-merit. BiTe and its derivative compounds, in particular, are well-known for their near-room temperature thermoelectric performance. In this work, both the binary and ternary BiTe-based nanowires namely, BiTe and BiSbTe, were synthesized using template-assisted electrodeposition. Diameters of the nanowires were controlled by the pore sizes of the anodised alumina (AAO) templates used. Systematic study on the compositional change as a function of applied potential was carried out via Linear Sweep Voltanmetry (LSV). Chemical compositions of the nanowires were studied using Energy Dispersive X-ray Spectrometry (EDXS) and their microstructures evaluated using diffraction and imaging techniques. Results from chemical analysis on the nanowires indicated that while the Sb content in BiSbTe nanowires increased with more negative deposition potentials, the formation of Te{sup 0} and Bi{sub 2}Te{sub 3} were favorable at more positive potentials.

  14. Price of Everett, MA Natural Gas LNG Imports from Algeria (Dollars per

    U.S. Energy Information Administration (EIA) Indexed Site

    Thousand Cubic Feet) Algeria (Dollars per Thousand Cubic Feet) Price of Everett, MA Natural Gas LNG Imports from Algeria (Dollars per Thousand Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1990's 2.56 2000's 3.48 4.82 3.77 -- -- -- -- - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date: 5/31/2016 Referring Pages: U.S. Price of Liquefied

  15. Price of Everett, MA Natural Gas LNG Imports from Egypt (Nominal Dollars

    U.S. Energy Information Administration (EIA) Indexed Site

    per Thousand Cubic Feet) Egypt (Nominal Dollars per Thousand Cubic Feet) Price of Everett, MA Natural Gas LNG Imports from Egypt (Nominal Dollars per Thousand Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 2000's -- -- 5.58 2010's 7.29 -- -- -- -- - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date: 5/31/2016 Referring Pages: U.S. Price

  16. Roadmap to MaRIE August 2015 (Technical Report) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    August 2015 Citation Details In-Document Search Title: Roadmap to MaRIE August 2015 Authors: Barnes, Cris William [1] + Show Author Affiliations Los Alamos National Lab. (LANL), Los Alamos, NM (United States) Publication Date: 2015-08-12 OSTI Identifier: 1211579 Report Number(s): LA-UR--15-26381 DOE Contract Number: AC52-06NA25396 Resource Type: Technical Report Research Org: Los Alamos National Lab. (LANL), Los Alamos, NM (United States) Sponsoring Org: USDOE Country of Publication: United

  17. Roadmap to MaRIE March 2015 (Technical Report) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    March 2015 Citation Details In-Document Search Title: Roadmap to MaRIE March 2015 Authors: Barnes, Cris William [1] + Show Author Affiliations Los Alamos National Lab. (LANL), Los Alamos, NM (United States) Publication Date: 2015-03-30 OSTI Identifier: 1177179 Report Number(s): LA-UR--15-22270 DOE Contract Number: AC52-06NA25396 Resource Type: Technical Report Research Org: Los Alamos National Laboratory (LANL), Los Alamos, NM (United States) Sponsoring Org: USDOE Country of Publication: United

  18. An Analysis of Wind Power Development in the Town of Hull, MA

    SciTech Connect (OSTI)

    Adams, Christopher

    2013-06-30

    Over the past three decades the Town of Hull, MA has solidified its place in U.S. wind energy history through its leadership in community-based generation. This is illustrated by its commissioning of the first commercial-scale wind turbine on the Atlantic coastline, the first suburban-sited turbine in the continental United States, pursuit of community-based offshore wind, and its push toward creating an energy independent community. The town's history and demographics are briefly outlined, followed by experience in projects to provide wind power, including pre-construction and feasibility efforts, financial aspects, and market/industry factors.

  19. Vehicle Technologies Office Merit Review 2015: MA3T—Modeling Vehicle Market Dynamics with Consumer Segmentation

    Broader source: Energy.gov [DOE]

    Presentation given by Oak Ridge National Laboratory at 2015 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about MA3T—modeling...

  20. Process Development for High Voc CdTe Solar Cells

    SciTech Connect (OSTI)

    Ferekides, C. S.; Morel, D. L.

    2011-05-01

    This is a cumulative and final report for Phases I, II and III of this NREL funded project (subcontract # XXL-5-44205-10). The main research activities of this project focused on the open-circuit voltage of the CdTe thin film solar cells. Although, thin film CdTe continues to be one of the leading materials for large-scale cost-effective production of photovoltaics, the efficiency of the CdTe solar cells have been stagnant for the last few years. This report describes and summarizes the results for this 3-year research project.

  1. Elemental characterization of LL-MA radioactive waste packages with the associated particle technique

    SciTech Connect (OSTI)

    Perot, B.; Carasco, C.; Toure, M.; El Kanawati, W.; Eleon, C.

    2011-07-01

    The French Alternative Energies and Atomic Energy Commission (CEA) and National Radioactive Waste Management Agency (ANDRA) are conducting an R and D program to improve the characterization of long-lived and medium activity (LL-MA) radioactive waste packages with analytical methods and with non-destructive nuclear measurements. This paper concerns fast neutron interrogation with the associated particle technique (APT), which brings 3D information about the waste material composition. The characterization of volume elements filled with iron, water, aluminium, and PVC in bituminized and fibre concrete LL-MA waste packages has been investigated with MCNP [1] and MODAR data analysis software [2]. APT provides usable information about major elements presents in the volumes of interest. However, neutron scattering on hydrogen nuclei spreads the tagged neutron beam out of the targeted volume towards surrounding materials, reducing spatial selectivity. Simulation shows that small less than 1 L targets can be characterised up to the half-radius of a 225 L bituminized drum, the matrix of which is very rich in hydrogen. Deeper characterization in concrete is possible but limited by counting statistics due to photon attenuation in this dense matrix and, unless large inspection volumes are considered, by the lack of spatial selectivity of the tagged neutron beam due to neutron scattering. (authors)

  2. Native defects in MBE-grown CdTe

    SciTech Connect (OSTI)

    Olender, Karolina; Wosinski, Tadeusz; Makosa, Andrzej; Tkaczyk, Zbigniew; Kolkovsky, Valery; Karczewski, Grzegorz

    2013-12-04

    Deep-level traps in both n- and p-type CdTe layers, grown by molecular-beam epitaxy on GaAs substrates, have been investigated by means of deep-level transient spectroscopy (DLTS). Four of the traps revealed in the DLTS spectra, which displayed exponential kinetics for capture of charge carriers into the trap states, have been assigned to native point defects: Cd interstitial, Cd vacancy, Te antisite defect and a complex formed of the Te antisite and Cd vacancy. Three further traps, displaying logarithmic capture kinetics, have been ascribed to electron states of treading dislocations generated at the mismatched interface with the substrate and propagated through the CdTe layer.

  3. Extreme solid state refrigeration using nanostructured Bi-Te alloys.

    SciTech Connect (OSTI)

    Lima Sharma, Ana L.; Spataru, Dan Catalin; Medlin, Douglas L.; Sharma, Peter Anand; Morales, Alfredo Martin

    2009-09-01

    Materials are desperately needed for cryogenic solid state refrigeration. We have investigated nanostructured Bi-Te alloys for their potential use in Ettingshausen refrigeration to liquid nitrogen temperatures. These alloys form alternating layers of Bi{sub 2} and Bi{sub 2}Te{sub 3} blocks in equilibrium. The composition Bi{sub 4}Te{sub 3} was identified as having the greatest potential for having a high Ettingshausen figure of merit. Both single crystal and polycrystalline forms of this material were synthesized. After evaluating the Ettingshausen figure of merit for a large, high quality polycrystal, we simulated the limits of practical refrigeration in this material from 200 to 77 K using a simple device model. The band structure was also computed and compared to experiments. We discuss the crystal growth, transport physics, and practical refrigeration potential of Bi-Te alloys.

  4. Summary of the TeV33 working group

    SciTech Connect (OSTI)

    Bagley, P.P.; Bieniosek, F.M.; Colestock, P.

    1996-10-01

    This summary of the TeV33 working group at Snowmass reports on work in the areas of Tevatron store parameters, the beam-beam interaction, Main Injector intensity (slip stacking), antiproton production, and electron cooling.

  5. PVA TePla AG | Open Energy Information

    Open Energy Info (EERE)

    search Name: PVA TePla AG Place: Asslar, Germany Zip: 35614 Product: Supplier of plants and equipment for vacuum systems, crystal-growing systems and plasma systems, some of...

  6. Substrate CdTe Efficiency Improvements - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Substrate CdTe Efficiency Improvements National Renewable Energy Laboratory Contact NREL About This Technology Publications: PDF Document Publication 11-28PCT Application as-published (984 KB) Technology Marketing Summary Thin film solar cells have been the focus of many research facilities in recent years that are working to decrease manufacturing costs and increase cell efficiency. Cadmium telluride (CdTe) has been well recognized as a promising photovoltaic material for thin film solar cells

  7. Phonon self-energy and origin of anomalous neutron scattering spectra in SnTe and PbTe thermoelectrics

    SciTech Connect (OSTI)

    Li, Chen [ORNL] [ORNL; Ma, Jie [ORNL] [ORNL; May, Andrew F [ORNL] [ORNL; Cao, Huibo [ORNL] [ORNL; Christianson, Andrew D [ORNL] [ORNL; Ehlers, Georg [ORNL] [ORNL; Singh, David J [ORNL] [ORNL; Sales, Brian C [ORNL] [ORNL; Delaire, Olivier A [ORNL] [ORNL

    2014-01-01

    The anharmonic lattice dynamics of rock-salt thermoelectric compounds SnTe and PbTe are investigated with inelastic neutron scattering (INS) and first-principles calculations. The experiments show that, surprisingly, although SnTe is closer to the ferroelectric instability, phonon spectra in PbTe exhibit a more anharmonic character. This behavior is reproduced in first-principles calculations of the temperature-dependent phonon self-energy. Our simulations reveal how the nesting of phonon dispersions induces prominent features in the self-energy, which account for the measured INS spectra and their temperature dependence. We establish that the phase-space for three-phonon scattering processes, rather than just the proximity to the lattice instability, is the mechanism determining the complex spectrum of the transverse-optical ferroelectric mode.

  8. The permeation behavior of deuterium through 1Cr18Ni9Ti stainless steel with TiN+TiC-TiN multiple films

    SciTech Connect (OSTI)

    Xiong, Y.; Song, J.; Luo, D.; Lei, Q.; Chen, C.

    2015-03-15

    The prevention of tritium losses via permeation through structure components is an important issue in fusion technology. The production of thin layers on materials with low diffusivity and/or low surface recombination constants (so-called permeation barriers) seems to be the most practical method to reduce or hinder the permeation of tritium through materials. TiN+TiC+TiN multiple films are deposited on the surface of 1Cr18Ni9Ti stainless steel by ion-beam assisted deposition technology. The characteristics of films are tested by XPS ASEM and XRD, which shows that the film are compact and uniform with a thickness of about 15 μm, and have a good adherence with the substrate below 773 K. The diffraction peaks in the XRD patterns for TiC and TiN are broadened, implying that the multiple films are deposited on the surface of 1Cr18Ni9Ti stainless steel. Meanwhile, the C-H bonded CH{sub 4}-appears in the infrared spectra of multiple films, suggesting that the CH{sub 4}- is in a static state, so hydrogen atom cannot migrate from the site bonded with carbon to a neighboring site. The measured deuterium permeability in 1Cr18Ni9Ti stainless steel coated with multiple films is 2-3 orders of magnitude lower than that of pure 1Cr18Ni9Ti stainless steel substrate from 473 K to 773 K. However, this barrier is partly destroyed above 773 K.

  9. Everett, MA Liquefied Natural Gas Imports From Yemen (Million Cubic Feet)

    U.S. Energy Information Administration (EIA) Indexed Site

    Imports From Yemen (Million Cubic Feet) Everett, MA Liquefied Natural Gas Imports From Yemen (Million Cubic Feet) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 2011 2,688 5,591 5,465 2,843 5,608 2,865 5,622 5,537 5,424 2012 2,805 2,765 2,721 2,589 2,899 2,837 2013 2,728 2,763 2,806 2,728 2014 2,329 2,806 2,871 2015 2,234 2,373 2,834 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next

  10. Everett, MA Natural Gas Liquefied Natural Gas Imports from Trinidad and

    U.S. Energy Information Administration (EIA) Indexed Site

    Tobago (Million Cubic Feet) Liquefied Natural Gas Imports from Trinidad and Tobago (Million Cubic Feet) Everett, MA Natural Gas Liquefied Natural Gas Imports from Trinidad and Tobago (Million Cubic Feet) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 2011 10,240 11,488 7,086 8,271 8,126 8,150 7,731 7,870 5,199 5,520 9,264 4,691 2012 9,482 8,458 7,661 1,447 4,940 5,465 6,646 10,377 5,634 4,748 2,553 2,581 2013 5,126 5,003 4,629 5,171 5,626 5,173 8,023 5,961 2,995 2,674 2,583 2014 3,141

  11. Ion-induced swelling of ODS ferritic alloy MA957 tubing to 500 dpa

    SciTech Connect (OSTI)

    Toloczko, Mychailo B.; Garner, F. A.; Voyevodin, V.; Bryk, V. V.; Borodin, O. V.; Melnichenko, V. V.; Kalchenko, A. S.

    2014-10-01

    In order to study the potential swelling behavior of the ODS ferritic alloy MA957 at very high dpa levels, specimens were prepared from pressurized tubes that were unirradiated archives of tubes previously irradiated in FFTF to doses as high at 110 dpa. These unirradiated specimens were irradiated with 1.8 MeV Cr+ ions to doses ranging from 100 to 500 dpa and examined by transmission electron microscopy. No coinjection of helium or hydrogen was employed. It was shown that compared to several ferritic/martensitic steels irradiated in the same facility, these tubes were rather resistant to void swelling, reaching a maximum value of only 4.5% at 500 dpa and 450°C. In this fine-grained material, the distribution of swelling was strongly influenced by the presence of void denuded zones along the grain boundaries.

  12. ?ot8rh QI ahnloal Corporation In Hart IUnover, Ma86rohusett8,

    Office of Legacy Management (LM)

    GE 1 ;" qr)-1 s?llq ' p raspy.. c" ifa K. mris I talked with Hr. Wllllm cIF(Iy, Metrllurgist, Wnlon CarbId@ Nuclear cOrp8ny, 08k B&t&$@, Tenne66ee, on April 26, 1961. He informed me th&t the #rtioMl Northern birislon, Ame~ic6.n ?ot8rh QI ahnloal Corporation In Hart IUnover, Ma86rohusett8, la pePfopn1~ lo8lve forming studier for the. ilnion olo)w Wuolem Conpmy "p l7?JHa). The work at National Northern l#rirc.- alon ir under the 6upenl6lon of Ehsll Phillpohuc4~, v of

  13. Larger sized wire arrays on 1.5 MA Z-pinch generator

    SciTech Connect (OSTI)

    Safronova, A. S. Kantsyrev, V. L. Weller, M. E. Shlyaptseva, V. V. Shrestha, I. K. Esaulov, A. A. Stafford, A.; Chuvatin, A. S.; Coverdale, C. A.; Jones, B.

    2014-12-15

    Experiments on the UNR Zebra generator with Load Current Multiplier (LCM) allow for implosions of larger sized wire array loads than at standard current of 1 MA. Advantages of larger sized planar wire array implosions include enhanced energy coupling to plasmas, better diagnostic access to observable plasma regions, and more complex geometries of the wire loads. The experiments with larger sized wire arrays were performed on 1.5 MA Zebra with LCM (the anode-cathode gap was 1 cm, which is half the gap used in the standard mode). In particular, larger sized multi-planar wire arrays had two outer wire planes from mid-atomic-number wires to create a global magnetic field (gmf) and plasma flow between them. A modified central plane with a few Al wires at the edges was put in the middle between outer planes to influence gmf and to create Al plasma flow in the perpendicular direction (to the outer arrays plasma flow). Such modified plane has different number of empty slots: it was increased from 6 up to 10, hence increasing the gap inside the middle plane from 4.9 to 7.7 mm, respectively. Such load configuration allows for more independent study of the flows of L-shell mid-atomic-number plasma (between the outer planes) and K-shell Al plasma (which first fills the gap between the edge wires along the middle plane) and their radiation in space and time. We demonstrate that such configuration produces higher linear radiation yield and electron temperatures as well as advantages of better diagnostics access to observable plasma regions and how the load geometry (size of the gap in the middle plane) influences K-shell Al radiation. In particular, K-shell Al radiation was delayed compared to L-shell mid-atomic-number radiation when the gap in the middle plane was large enough (when the number of empty slots was increased up to ten)

  14. Influence of Mn concentration on magnetic topological insulator MnxBi2−xTe3 thin-film Hall-effect sensor

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Ni, Y.; Zhang, Z.; Nlebedim, I. C.; Hadimani, R. L.; Jiles, D. C.

    2015-06-11

    Hall-effect (HE) sensors based on high-quality Mn-doped Bi2Te3 topological insulator (TI) thin films have been systematically studied in this paper. Improvement of Hall sensitivity is found after doping the magnetic element Mn into Bi2Te3. The sensors with low Mn concentrations, MnxBi2-xTe3, x = 0.01 and 0.08 show the linear behavior of Hall resistance with sensitivity about 5 Ω/T. And their Hall sensitivity shows weak dependence on temperature. For sensors with high Mn concentration (x = 0.23), the Hall resistance with respect to magnetic field shows a hysteretic behavior. Moreover, its sensitivity shows almost eight times as high as that ofmore »the HE sensors with low Mn concentration. The highest sensitivity can reach 43 Ω/T at very low magnetic field. This increase of Hall sensitivity is caused by the occurrence of anomalous HE (AHE) after ferromagnetic phase transition. Our work indicates that the magnetic-element-doped TIs with AHE are good candidates for HE sensors.« less

  15. Influence of Mn concentration on magnetic topological insulator MnxBi2−xTe3 thin-film Hall-effect sensor

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Ni, Y.; Zhang, Z.; Nlebedim, I. C.; Hadimani, R. L.; Jiles, D. C.

    2015-06-11

    Hall-effect (HE) sensors based on high-quality Mn-doped Bi2Te3 topological insulator (TI) thin films have been systematically studied in this paper. Improvement of Hall sensitivity is found after doping the magnetic element Mn into Bi2Te3. The sensors with low Mn concentrations, MnxBi2-xTe3, x = 0.01 and 0.08 show the linear behavior of Hall resistance with sensitivity about 5 Ω/T. And their Hall sensitivity shows weak dependence on temperature. For sensors with high Mn concentration (x = 0.23), the Hall resistance with respect to magnetic field shows a hysteretic behavior. Moreover, its sensitivity shows almost eight times as high as that ofmore » the HE sensors with low Mn concentration. The highest sensitivity can reach 43 Ω/T at very low magnetic field. This increase of Hall sensitivity is caused by the occurrence of anomalous HE (AHE) after ferromagnetic phase transition. Our work indicates that the magnetic-element-doped TIs with AHE are good candidates for HE sensors.« less

  16. Ti Leggett | Argonne Leadership Computing Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Ti Leggett Deputy Project Directcor & Deputy Director of Operations Argonne National Laboratory 9700 S. Cass Avenue Building 240 - Room 3132 Argonne, IL 60439 630-252-1937 tleggett

  17. A=18Li (1995TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Li (1995TI07) (Not illustrated) 18Li has not been observed. Shell model calculations described in (1988POZS) predict the ground-state magentic dipole moment and charge and matter...

  18. A=8Be (2004TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2004TI06) (See Energy Level Diagrams for 8Be) GENERAL: References to articles on general properties of 8Be published since the previous review (1988AJ01) are grouped into...

  19. A=10B (2004TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2004TI06) (See Energy Level Diagrams for 10B) GENERAL: References to articles on general properties of 10B published since the previous review (1988AJ01) are grouped into...

  20. A=7Be (2002TI10)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2002TI10) (See Energy Level Diagrams for 7Be) GENERAL: References to articles on general properties of 7Be published since the previous review (1988AJ01) are grouped into...

  1. A=8He (2004TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2004TI06) (See Energy Level Diagrams for 8He) GENERAL: References to articles on general properties of 8He published since the previous review (1988AJ01) are grouped into...

  2. A=9C (2004TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2004TI06) (See Energy Level Diagrams for 9C) GENERAL: References to articles on general properties of 9C published since the previous review (1988AJ01) are grouped into categories...

  3. A=7He (2002TI10)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2002TI10) (See Energy Level Diagrams for 7He) GENERAL: References to articles on general properties of 7He published since the previous review (1988AJ01) are grouped into...

  4. A=9Be (2004TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2004TI06) (See Energy Level Diagrams for 9Be) GENERAL: References to articles on general properties of 9Be published since the previous review (1988AJ01) are grouped into...

  5. A=10C (2004TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2004TI06) (See Energy Level Diagrams for 10C) GENERAL: References to articles on general properties of 10C published since the previous review (1988AJ01) are grouped into...

  6. A=8B (2004TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2004TI06) (See Energy Level Diagrams for 8B) GENERAL: References to articles on general properties of 8B published since the previous review (1988AJ01) are grouped into categories...

  7. A=10N (2004TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2004TI06) (Not illustrated) GENERAL: References to articles on general properties of 10N published since the previous review (1988AJ01) are grouped into categories and listed,...

  8. A=10Li (2004TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2004TI06) (See Energy Level Diagrams for 10Li) GENERAL: References to articles on general properties of 10Li published since the previous review (1988AJ01) are grouped into...

  9. A=6Be (2002TI10)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2002TI10) (See Energy Level Diagrams for 6Be) GENERAL: References to articles on general properties of 6Be published since the previous review (1988AJ01) are grouped into...

  10. A=9He (2004TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2004TI06) (See the Isobar Diagram for 9He) GENERAL: References to articles on general properties of 9He published since the previous review (1988AJ01) are grouped into categories...

  11. A=5Li (2002TI10)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2002TI10) (See Energy Level Diagrams for 5Li) GENERAL: References to articles on general properties of 5Li published since the previous review (1988AJ01) are grouped into...

  12. A=9Li (2004TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2004TI06) (See Energy Level Diagrams for 9Li) GENERAL: References to articles on general properties of 9Li published since the previous review (1988AJ01) are grouped into...

  13. A=9B (2004TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2004TI06) (See Energy Level Diagrams for 9B) GENERAL: References to articles on general properties of 9B published since the previous review (1988AJ01) are grouped into categories...

  14. A=10He (2004TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2004TI06) (See Energy Level Diagrams for 10He) GENERAL: References to articles on general properties of 10He published since the previous review (1988AJ01) are grouped into...

  15. A=18Mg, etc. (1995TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    95TI07) (Not observed) See (1986AN07) and (1983ANZQ). See also the results of calculations of β+/electron capture half lives for neutron deficient nuclei in (1993HI08

  16. A=6B (2002TI10)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2002TI10) (Not illustrated) Not observed: see ( 1984AJ01, 1989GR06 [6Li(π+, π-) at Eπ+ = 180, 240 MeV], 1993PO11 [properties of exotic light nuclei]) (1998SU18

  17. A=6C (2002TI10)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2002TI10) (Not illustrated) Not observed: see (1979AJ01, 1984AJ01, 1989GR06 [6Li(π+, π-) at Eπ+ = 180, 240 MeV], 1993PO11 [properties of exotic light nuclei]) (1998SU18

  18. A=9N (2004TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2004TI06) (Not illustrated) Not observed: see (1988AJ01). Mass excesses of 46.56 and 46.40 MeV have been estimated from two different mass formulae (2000PO32). 9N would then be...

  19. TiBor Skin - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Advanced Materials Advanced Materials Find More Like This Return to Search TiBor Skin Y-12 National Security Complex Contact Y12 About This Technology Publications: PDF Document Publication Fact Sheet (336 KB) PDF Document Publication Presentation (400 KB) PDF Document Publication Patent Application Publication (2,825 KB) Technology Marketing Summary Y-12 invites interested companies to license its patent-pending method known as TiBor Skin. This two-part technology enables creation and

  20. Heterojunctions of model CdTe/CdSe mixtures

    SciTech Connect (OSTI)

    van Swol, Frank; Zhou, Xiaowang W.; Challa, Sivakumar R.; Martin, James E.

    2015-03-18

    We report on the strain behavior of compound mixtures of model group IIVI semiconductors. We use the StillingerWeber Hamiltonian that we recently introduced, specifically developed to model binary mixtures of group IIVI compounds such as CdTe and CdSe. We also employ molecular dynamics simulations to examine the behavior of thin sheets of material, bilayers of CdTe and CdSe. The lattice mismatch between the two compounds leads to a strong bending of the entire sheet, with about a 0.5 to 1 deflection between neighboring planes. To further analyze bilayer bending, we introduce a simple one-dimensional model and use energy minimization to find the angle of deflection. The analysis is equivalent to a least-squares straight line fit. We consider the effects of bilayers which are asymmetric with respect to the thickness of the CdTe and CdSe parts. We thus learn that the bending can be subdivided into four kinds depending on the compressive/tensile nature of each outer plane of the sheet. We use this approach to directly compare our findings with experimental results on the bending of CdTe/CdSe rods. To reduce the effects of the lattice mismatch we explore diffuse interfaces, where we mix (i.e. alloy) Te and Se, and estimate the strain response.

  1. Heterojunctions of model CdTe/CdSe mixtures

    SciTech Connect (OSTI)

    van Swol, Frank; Zhou, Xiaowang W.; Challa, Sivakumar R.; Martin, James E.

    2015-03-18

    We report on the strain behavior of compound mixtures of model group II-VI semiconductors. We use the Stillinger-Weber Hamiltonian that we recently introduced, specifically developed to model binary mixtures of group II-VI compounds such as CdTe and CdSe. We also employ molecular dynamics simulations to examine the behavior of thin sheets of material, bilayers of CdTe and CdSe. The lattice mismatch between the two compounds leads to a strong bending of the entire sheet, with about a 0.5 to 1° deflection between neighboring planes. To further analyze bilayer bending, we introduce a simple one-dimensional model and use energy minimization to find the angle of deflection. The analysis is equivalent to a least-squares straight line fit. We consider the effects of bilayers which are asymmetric with respect to the thickness of the CdTe and CdSe parts. We thus learn that the bending can be subdivided into four kinds depending on the compressive/tensile nature of each outer plane of the sheet. We use this approach to directly compare our findings with experimental results on the bending of CdTe/CdSe rods. To reduce the effects of the lattice mismatch we explore diffuse interfaces, where we mix (i.e. alloy) Te and Se, and estimate the strain response.

  2. Heterojunctions of model CdTe/CdSe mixtures

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    van Swol, Frank; Zhou, Xiaowang W.; Challa, Sivakumar R.; Martin, James E.

    2015-03-18

    We report on the strain behavior of compound mixtures of model group II-VI semiconductors. We use the Stillinger-Weber Hamiltonian that we recently introduced, specifically developed to model binary mixtures of group II-VI compounds such as CdTe and CdSe. We also employ molecular dynamics simulations to examine the behavior of thin sheets of material, bilayers of CdTe and CdSe. The lattice mismatch between the two compounds leads to a strong bending of the entire sheet, with about a 0.5 to 1° deflection between neighboring planes. To further analyze bilayer bending, we introduce a simple one-dimensional model and use energy minimization tomore » find the angle of deflection. The analysis is equivalent to a least-squares straight line fit. We consider the effects of bilayers which are asymmetric with respect to the thickness of the CdTe and CdSe parts. We thus learn that the bending can be subdivided into four kinds depending on the compressive/tensile nature of each outer plane of the sheet. We use this approach to directly compare our findings with experimental results on the bending of CdTe/CdSe rods. To reduce the effects of the lattice mismatch we explore diffuse interfaces, where we mix (i.e. alloy) Te and Se, and estimate the strain response.« less

  3. Instability of Hydrogenated TiO2

    SciTech Connect (OSTI)

    Nandasiri, Manjula I.; Shutthanandan, V.; Manandhar, Sandeep; Schwarz, Ashleigh M.; Oxenford, Lucas S.; Kennedy, John V.; Thevuthasan, Suntharampillai; Henderson, Michael A.

    2015-11-06

    Hydrogenated TiO2 (H-TiO2) is toted as a viable visible light photocatalyst. We report a systematic study on the thermal stability of H-implanted TiO2 using X-ray photoelectron spectroscopy (XPS), ultraviolet photoelectron spectroscopy (UPS), Rutherford backscattering spectrometry (RBS) and nuclear reaction analysis (NRA). Protons (40 keV) implanted at a ~2 atom % level within a ~120 nm wide profile of rutile TiO2(110) were situated ~300 nm below the surface. NRA revealed that this H-profile broadened preferentially toward the surface after annealing at 373 K, dissipated out of the crystal into vacuum at 473 K, and was absent within the beam sampling depth (~800 nm) at 523 K. Photoemission showed that the surface was reduced in concert with these changes. Similar anneals had no effect on pristine TiO2(110). The facile bulk diffusivity of H in rutile, as well as its activity toward interfacial reduction, significantly limits the utilization of H-TiO2 as a photocatalyst. This work was supported by the US Department of Energy, Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences & Biosciences. Pacific Northwest National Laboratory (PNNL) is a multiprogram national laboratory operated for DOE by Battelle. The research was performed using the Environmental Molecular Sciences Laboratory (EMSL), a national scientific user facility sponsored by the Department of Energy's Office of Biological and Environmental Research and located at Pacific Northwest National Laboratory.

  4. Imaging dirac-mass disorder from magnetic dopant-atoms in the ferromagnetic topological insulator Crx(Bi?.?Sb?.?)??xTe?

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Lee, Inhee; Kim, Chung Koo; Lee, Jinho; Billinge, Simon J. L.; Zhong, Ruidan D.; Schneeloch, John A.; Liu, Tiansheng S.; Valla, Tonica; Tranquada, John M.; Gu, Genda; et al

    2015-01-20

    To achieve and use the most exotic electronic phenomena predicted for the surface states of 3D topological insulators (TIs), it is necessary to open a Dirac-mass gap in their spectrum by breaking time-reversal symmetry. Use of magnetic dopant atoms to generate a ferromagnetic state is the most widely applied approach. However, it is unknown how the spatial arrangements of the magnetic dopant atoms influence the Dirac-mass gap at the atomic scale or, conversely, whether the ferromagnetic interactions between dopant atoms are influenced by the topological surface states. Here we image the locations of the magnetic (Cr) dopant atoms in themoreferromagnetic TI Cr?.??(Bi?.?Sb?.?)?.??Te?. Simultaneous visualization of the Dirac-mass gap ?(r) reveals its intense disorder, which we demonstrate is directly related to fluctuations in n(r), the Cr atom areal density in the termination layer. We find the relationship of surface-state Fermi wavevectors to the anisotropic structure of ?(r) not inconsistent with predictions for surface ferromagnetism mediated by those states. Moreover, despite the intense Dirac-mass disorder, the anticipated relationship ?(r)?n(r) is confirmed throughout and exhibits an electrondopant interaction energy J* = 145 meVnm. These observations reveal how magnetic dopant atoms actually generate the TI mass gap locally and that, to achieve the novel physics expected of time-reversal symmetry breaking TI materials, control of the resulting Dirac-mass gap disorder will be essential.less

  5. The half-life of {sup 131g,m}Te

    SciTech Connect (OSTI)

    Ruivo, J. C.; Zamboni, C. B.; Oliveira, J. R. B.; Heder Medina, Nilberto

    2013-05-06

    In this work, the half-lives of {sup 131m}Te and {sup 131g}Te were measured. Radioactive sources of {sup 131}Te were obtained using the {sup 130}Te(n,{gamma}){sup 131}Te nuclear reaction. These nuclear parameters have been determined with a better confidence and accuracy than previously available: 18.89 {+-} 0.11 min and 33.18 {+-} 0.13 h, respectively. These results are quite helpful for new calculations that attempt to describe the low-lying levels in {sup 131}I from the decay of {sup 131g,m}Te.

  6. Growth, steady-state, and time-resolved photoluminescence study of CdTe/MgCdTe double heterostructures on InSb substrates using molecular beam epitaxy

    SciTech Connect (OSTI)

    DiNezza, Michael J.; Liu, Shi; Kirk, Alexander P.; Zhang, Yong-Hang; School of Electrical, Computer and Energy Engineering, Arizona State University, Tempe, Arizona 85287 ; Zhao, Xin-Hao; School for Engineering of Matter, Transport and Energy, Arizona State University, Tempe, Arizona 85287

    2013-11-04

    CdTe/MgCdTe double heterostructures (DHs) are grown on InSb substrates using molecular beam epitaxy and reveal strong photoluminescence with over double the intensity of a GaAs/AlGaAs DH with an identical layer structure design grown on GaAs. Time-resolved photoluminescence of the CdTe/MgCdTe DH gives a Shockley-Read-Hall recombination lifetime of 86 ns, which is more than one order of magnitude longer than that of typical polycrystalline CdTe films. These findings indicate that monocrystalline CdTe/MgCdTe DHs effectively reduce surface recombination, have limited nonradiative interface recombination, and are promising for solar cells that could reach power conversion efficiencies similar to that of GaAs.

  7. Current enhancement of CdTe-based solar cells

    SciTech Connect (OSTI)

    Paudel, Naba R.; Poplawsky, Jonathan D.; More, Karren Leslie; Yan, Yanfa

    2015-07-30

    We report on the realization of CdTe solar cell photocurrent enhancement using an n-type CdSe heterojunction partner sputtered on commercial SnO2/SnO2:F coated soda-lime glass substrates. With high-temperature close-space sublimation CdTe deposition followed by CdCl2 activation, this thin-film stack allows for substantial interdiffusion at the CdSe/CdTe interface facilitating a CdSexTe1-x alloy formation. The bowing effect causes a reduced optical bandgap of the alloyed absorber layer and, therefore, leads to current enhancement in the long-wavelength region and a decrease in open-circuit voltage (VOC). To overcome the VOC loss and maintain a high short-circuit current (JSC), the CdTe cell configuration has been modified using combined CdS:O/CdSe window layers. The new device structure has demonstrated enhanced collection from both short-and long-wavelength regions as well as a VOC improvement. With an optimized synthesis process, a small-area cell using CdS:O/CdSe window layer showed an efficiency of 15.2% with a VOC of 831 mV, a JSC of 26.3 mA/cm2, and a fill factor of 69.5%, measured under an AM1.5 illumination without antireflection coating. Furthermore, the results provide new directions for further improvement of CdTe-based solar cells.

  8. Current enhancement of CdTe-based solar cells

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Paudel, Naba R.; Poplawsky, Jonathan D.; More, Karren Leslie; Yan, Yanfa

    2015-07-30

    We report on the realization of CdTe solar cell photocurrent enhancement using an n-type CdSe heterojunction partner sputtered on commercial SnO2/SnO2:F coated soda-lime glass substrates. With high-temperature close-space sublimation CdTe deposition followed by CdCl2 activation, this thin-film stack allows for substantial interdiffusion at the CdSe/CdTe interface facilitating a CdSexTe1-x alloy formation. The bowing effect causes a reduced optical bandgap of the alloyed absorber layer and, therefore, leads to current enhancement in the long-wavelength region and a decrease in open-circuit voltage (VOC). To overcome the VOC loss and maintain a high short-circuit current (JSC), the CdTe cell configuration has been modifiedmore » using combined CdS:O/CdSe window layers. The new device structure has demonstrated enhanced collection from both short-and long-wavelength regions as well as a VOC improvement. With an optimized synthesis process, a small-area cell using CdS:O/CdSe window layer showed an efficiency of 15.2% with a VOC of 831 mV, a JSC of 26.3 mA/cm2, and a fill factor of 69.5%, measured under an AM1.5 illumination without antireflection coating. Furthermore, the results provide new directions for further improvement of CdTe-based solar cells.« less

  9. Early time studies of cylindrical liner implosions at 1 MA on COBRA

    SciTech Connect (OSTI)

    Atoyan, L. Byvank, T. Cahill, A. D. Hoyt, C. L. Grouchy, P. W. L. de Potter, W. M. Kusse, B. R. Hammer, D. A.

    2014-12-15

    Tests of the magnetized liner inertial fusion (MagLIF) concept will make use of the 27 MA Z machine at Sandia National Laboratories, Albuquerque, to implode a cylindrical metal liner to compress and heat preheated, magnetized plasma contained within it. While most pulsed power machines produce much lower currents than the Z-machine, there are issues that can still be addressed on smaller scale facilities. Recent work on the Cornell Beam Research Accelerator (COBRA) has made use of 10 mm long and 4 mm diameter metal liners having different wall thicknesses to study the initiation of plasma on the liner’s surface as well as axial magnetic field compression [P.-A. Gourdain et al., Nucl. Fusion 53, 083006 (2013)]. This report presents experimental results with non-imploding liners, investigating the impact the liner’s surface structure has on initiation and ablation. Extreme ultraviolet (XUV) imaging and optical 12 frame camera imaging were used to observe and assess emission non-uniformities as they developed. Axial and side-on interferometry was used to determine the distribution of plasma near the liner surface, including the impact of non-uniformities during the plasma initiation and ablation phases of the experiments.

  10. CsBi4Te6: A High-Performance Thermoelectric Material for Low...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    thermoelectric properties of CsBi(4)Te(6) appear to match or exceed those of Bi(2-x)Sb(x)Te(3-y)Se(y) alloys. URL: Link to article - National Center for Biotechnology Information

  11. Resonant Level Enhancement of the Thermoelectric Power of Bi2Te3...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Resonant Level Enhancement of the Thermoelectric Power of Bi2Te3 with Tin Resonant Level Enhancement of the Thermoelectric Power of Bi2Te3 with Tin Application to practical p-type...

  12. Energy Sources for Yotta-TeV Iceberg Showers (Conference) | SciTech...

    Office of Scientific and Technical Information (OSTI)

    Energy Sources for Yotta-TeV Iceberg Showers Citation Details In-Document Search Title: Energy Sources for Yotta-TeV Iceberg Showers You are accessing a document from the ...

  13. ETA-HAC07 - Control of Measuring and Test Equipment (M&TE)

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Control of Measuring and Test Equipment (M&TE) Prepared by Electric Transportation ... The objective of this procedure is to assure that Measuring and Test Equipment (M&TE) used ...

  14. ETA-HIAC07 - Control of Measuring and Test Equipment (M&TE)

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Control of Measuring and Test Equipment (M&TE) Prepared by Electric Transportation ... The objective of this procedure is to assure that Measuring and Test Equipment (M&TE) used ...

  15. Probing TeV physics in the structure of the neutron (Technical...

    Office of Scientific and Technical Information (OSTI)

    Probing TeV physics in the structure of the neutron Citation Details In-Document Search Title: Probing TeV physics in the structure of the neutron You are accessing a document ...

  16. CdTe Thin Film Solar Cells and Modules Tutorial; NREL (National Renewable Energy Laboratory)

    SciTech Connect (OSTI)

    Albin, David S.

    2015-06-13

    This is a tutorial presented at the 42nd IEEE Photovoltaics Specialists Conference to cover the introduction, background, and updates on CdTe cell and module technology, including CdTe cell and module structure and fabrication.

  17. Probing TeV physics in the structure of the neutron (Technical...

    Office of Scientific and Technical Information (OSTI)

    Technical Report: Probing TeV physics in the structure of the neutron Citation Details In-Document Search Title: Probing TeV physics in the structure of the neutron Authors: Gupta, ...

  18. Pressure-induced Phase Transition in Thiol-capped CdTe Nanoparticles

    SciTech Connect (OSTI)

    Wu, F; Zaug, J; Young, C; Zhang, J Z

    2006-11-29

    Phase transitions for CdTe nanoparticles (NPs) under high pressure up to 37.0 GPa have been studied using fluorescence measurements. The phase transition from cinnarbar to rocksalt phase has been observed in CdTe NPs solution at 5.8 GPa, which is much higher than the phase transition pressure of bulk CdTe (3.8 GPa) and that of CdTe NPs in solid form (0.8 GPa). CdTe NPs solution therefore shows elevated phase transition pressure and enhanced stability against pressure compared with bulk CdTe and CdTe NPs in solid forms. The enhanced stability of CdTe NPs solution has been attributed to possible shape change in the phase transition and/or inhomogeneous strains in nanoparticle solutions.

  19. Facile method for synthesis of TiO{sub 2} film and its application in high efficiency dye sensitized-solar cell (DSSC)

    SciTech Connect (OSTI)

    Widiyandari, Hendri Gunawan, S. K.V.; Suseno, Jatmiko Endro; Purwanto, Agus; Diharjo, Kuncoro

    2014-02-24

    Dye-sensitized solar cells (DSSC) is a device which converts a solar energy to electrical energy. Different with semiconductor thin film based solar cell, DSSC utilize the sensitized-dye to absorb the photon and semiconductor such as titanium dioxide (TiO{sub 2}) and zinc oxide (ZnO) as a working electrode photoanode. In this report, the preparation of TiO{sub 2} film using a facile method of spray deposition and its application in DSSC have been presented. TiO{sub 2} photoanode was synthesized by growing the droplet of titanium tetraisopropoxide diluted in acid solution on the substrate of conductive glass flourine-doped tin oxide (FTO) with variation of precursor volume. DSSC was assemblied by sandwiching both of photoanode electrode and platinum counter electrode subsequently filling the area between these electrodes with triodine/iodine electrolite solution as redox pairs. The characterization of the as prepared DSSC using solar simulator (AM 1.5G, 100 mW/cm{sup 2}) and I-V source meter Keithley 2400 showed that the performance of DSSC was affected by the precursor volume.. The overall conversion efficiency of DSSC using the optimum TiO{sub 2} film was about 1.97% with the open circuit voltage (V{sub oc}) of 0.73 V, short circuit current density (J{sub sc}) of 4.61 mA and fill factor (FF) of 0.58.

  20. Junction Evolution During Fabrication of CdS/CdTe Thin-film PV Solar Cells (Presentation)

    SciTech Connect (OSTI)

    Gessert, T. A.

    2010-09-01

    Discussion of the formation of CdTe thin-film PV junctions and optimization of CdTe thin-film PV solar cells.

  1. TeVeS gets caught on caustics

    SciTech Connect (OSTI)

    Contaldi, Carlo R.; Wiseman, Toby; Withers, Benjamin

    2008-08-15

    TeVeS uses a dynamical vector field with timelike unit-norm constraint to specify a preferred local frame. When matter moves slowly in this frame--the so-called quasistatic regime--modified Newtonian dynamics results. Theories with such vectors (such as Einstein-Aether) are prone to the vector dynamics forming singularities that render their classical evolution problematic. Here, we analyze the dynamics of the vector in TeVeS in various situations. We begin by analytically showing that the vacuum solution of TeVeS forms caustic singularities under a large class of physically reasonably initial perturbations. This shows the classical evolution of TeVeS appears problematic in the absence of matter. We then consider matter by investigating black hole solutions. We find large classes of new black hole solutions with static geometries, where the curves generated by the vector field are attracted to the black hole and may form caustics. We go on to consider the full dynamics with matter by numerically simulating, assuming spherical symmetry, the gravitational collapse of a scalar, and the evolution of an initially nearly static boson star. We find that in both cases our initial data evolves so that the vector field develops caustic singularities on a time scale of order the gravitational in-fall time. Having shown singularity formation is generic with or without matter, Bekenstein's original formulation of TeVeS appears dynamically problematic. We argue that by modifying the vector field kinetic terms to the more general form used by Einstein-Aether, this problem may be avoided.

  2. Morphology, deformation, and defect structures of TiCr{sub 2} in Ti-Cr alloys

    SciTech Connect (OSTI)

    Chen, K.C.; Allen, S.M.; Livingston, J.D.

    1992-12-31

    The morphologies and defect structures of TiCr{sub 2} in several Ti-Cr alloys have been examined by optical metallography, x-ray diffraction, and transmission electron microscopy (TEM), in order to explore the room-temperature deformability of the Laves phase TiCr{sub 2}. The morphology of the Laves phase was found to be dependent upon alloy composition and annealing temperature. Samples deformed by compression have also been studied using TEM. Comparisons of microstructures before and after deformation suggest an increase in twin, stacking fault, and dislocation density within the Laves phase, indicating some but not extensive room-temperature deformability.

  3. Reverse Monte Carlo simulation of Se{sub 80}Te{sub 20} and Se{sub 80}Te{sub 15}Sb{sub 5} glasses

    SciTech Connect (OSTI)

    Abdel-Baset, A. M.; Rashad, M.; Moharram, A. H.

    2013-12-16

    Two-dimensional Monte Carlo of the total pair distribution functions g(r) is determined for Se{sub 80}Te{sub 20} and Se{sub 80}Te{sub 15}Sb{sub 5} alloys, and then it used to assemble the three-dimensional atomic configurations using the reverse Monte Carlo simulation. The partial pair distribution functions g{sub ij}(r) indicate that the basic structure unit in the Se{sub 80}Te{sub 15}Sb{sub 5} glass is di-antimony tri-selenide units connected together through Se-Se and Se-Te chain. The structure of Se{sub 80}Te{sub 20} alloys is a chain of Se-Te and Se-Se in addition to some rings of Se atoms.

  4. Carrier-Controlled Ferromagnetism in SrTiO3

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Moetakef, Pouya; Williams, James R.; Ouellette, Daniel G.; Kajdos, Adam P.; Goldhaber-Gordon, David; Allen, S. James; Stemmer, Susanne

    2012-06-27

    Magnetotransport and superconducting properties are investigated for uniformly La-doped SrTiO3 films and GdTiO3/SrTiO3 heterostructures, respectively. GdTiO3/SrTiO3 interfaces exhibit a high-density 2D electron gas on the SrTiO3 side of the interface, while, for the SrTiO3 films, carriers are provided by the dopant atoms. Both types of samples exhibit ferromagnetism at low temperatures, as evidenced by a hysteresis in the magnetoresistance. For the uniformly doped SrTiO3 films, the Curie temperature is found to increase with doping and to coexist with superconductivity for carrier concentrations on the high-density side of the superconducting dome. The Curie temperature of the GdTiO3/SrTiO3 heterostructures scales with themore » thickness of the SrTiO3 quantum well. The results are used to construct a stability diagram for the ferromagnetic and superconducting phases of SrTiO3.« less

  5. Superconducting Bi2Te: Pressure-induced universality in the (Bi2)m(Bi2Te3)n series

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Stillwell, Ryan L.; Jeffries, Jason R.; Jenei, Zsolt; Weir, Samuel T.; Vohra, Yogesh K.

    2016-03-09

    Using high-pressure magnetotransport techniques we have discovered superconductivity in Bi2Te, a member of the infinitely adaptive (Bi2)m(Bi2Te3)n series, whose end members, Bi and Bi2Te3, can be tuned to display topological surface states or superconductivity. Bi2Te has a maximum Tc = 8.6 K at P = 14.5 GPa and goes through multiple high pressure phase transitions, ultimately collapsing into a bcc structure that suggests a universal behavior across the series. High-pressure magnetoresistance and Hall measurements suggest a semi-metal to metal transition near 5.4 GPa, which accompanies the hexagonal to intermediate phase transition seen via x-ray diffraction measurements. In addition, the linearitymore » of Hc2 (T) exceeds the Werthamer-Helfand-Hohenberg limit, even in the extreme spin-orbit scattering limit, yet is consistent with other strong spin-orbit materials. Furthermore, considering these results in combination with similar reports on strong spin-orbit scattering materials seen in the literature, we suggest the need for a new theory that can address the unconventional nature of their superconducting states.« less

  6. Surfactant-Free Synthesis of Bi?Te?-Te Micro-Nano Heterostructure with Enhanced Thermoelectric Figure of Merit

    SciTech Connect (OSTI)

    Zhang, Yichi; Wang, Heng; Kraemer, Stephan; Shi, Yifeng; Zhang, Fan; Snedaker, Matt; Ding, Kunlun; Moskovits, Martin; Snyder, G. Jeffrey; Stucky, Galen D.

    2011-01-01

    An ideal thermoelectric material would be a semiconductor with high electrical conductivity and relatively low thermal conductivity: an electron crystal, phonon glass. Introducing nanoscale heterostructures into the bulk TE matrix is one way of achieving this intuitively anomalous electron/phonon transport behavior. The heterostructured interfaces are expected to play a significant role in phonon scattering to reduce thermal conductivity and in the energy-dependent scattering of electrical carriers to improve the Seebeck coefficient. A nanoparticle building block assembly approach is plausible to fabricate three-dimensional heterostructured materials on a bulk commercial scale. However, a key problem in applying this strategy is the possible negative impact on TE performance of organic residue from the nanoparticle capping ligands. Herein, we report a wet chemical, surfactant-free, low-temperature, and easily up-scalable strategy for the synthesis of nanoscale heterophase Bi?Te?-Te via a galvanic replacement reaction. The micro-nano heterostructured material is fabricated bottom-up, by mixing the heterophase with commercial Bi?Te?. This unique structure shows an enhanced zT value of ~0.4 at room temperature. This heterostructure has one of the highest figures of merit among bismuth telluride systems yet achieved by a wet chemical bottom-up assembly. In addition, it shows a 40% enhancement of the figure of merit over our lab-made material without nanoscale heterostructures. This enhancement is mainly due to the decrease in the thermal conductivity while maintaining the power factor. Overall, this cost-efficient and room-temperature synthesis methodology provides the potential for further improvement and large-scale thermoelectric applications.

  7. Giant persistent photoconductivity in BaTiO{sub 3}/TiO{sub 2} heterostructures

    SciTech Connect (OSTI)

    Plodinec, Milivoj; anti?, Ana; Gajovi?, Andreja; Zavanik, Janez; ?eh, Miran

    2014-10-13

    The persistent photoconductivity (PPC) effect in nanotube arrays of barium titanate and TiO{sub 2} (BTO/TiO{sub 2}NT) was studied at room temperature under daylight illumination. The BTO/TiO{sub 2}NT heterostructures exhibited a giant PPC effect that was six orders of magnitude higher than the dark conductivity, followed by a slow relaxation for 3 h. The PPC in this material was explained by the existence of defects at the surfaces and the interfaces of the investigated heterostructures. The sample was prepared using a two-step synthesis: the anodization of a Ti-foil and a subsequent hydrothermal synthesis. The structural and electrical characteristics were studied by micro-Raman spectroscopy, field-emission-gun scanning electron microscopy, and impedance spectroscopy.

  8. Irradiation Creep and Swelling from 400 C to 600 C of the Oxide Dispersion Strengthened Ferritic Alloy MA957

    SciTech Connect (OSTI)

    Toloczko, Mychailo B.; Gelles, David S.; Garner, Francis A.; Kurtz, Richard J.; Abe, Katsunori

    2004-04-24

    Recently, there has been a growing interest in the use of oxide dispersion strengthened (ODS) ferritic steels for fusion reactor applications. As part of an extensive study performed at PNNL on the ODS steel MA957 [1], irradiation creep tests were performed on pressurized tubes made from MA957 by two different methods. The tubes were made either by gun drilling alone or by a combination of rod drawing and gun drilling. The different fabrication methods were explored because ODS steels have been difficult to form. The pressurized tubes were irradiated in the Fast Flux Test Facility (FFTF) to doses ranging from 40 dpa to 110 dpa at temperatures ranging from 400 C to 600 C. The effective stresses resulting from the pressurization of the tubes ranged from 0 MPa to 175 MPa.

  9. Characterization of Residual Stress as a Function of Friction Stir Welding Parameters in Oxide Dispersion Strengthened (ODS) Steel MA956

    SciTech Connect (OSTI)

    Brewer, Luke N.; Bennett, Martin S.; Baker, B. W.; Payzant, E. Andrew; Kolbus, Lindsay M.

    2015-09-08

    This article characterizes the residual stresses generated by friction stir welding of oxide dispersion strengthened steel MA956 over a series of welding conditions. A plate of MA956 steel was friction stir welded at three conditions: 500 rpm/25 millimeters per minute (mmpm), 400 rpm/50 mmpm and 400 rpm/100 mmpm. The residual stresses across these welds were measured using both x-ray and neutron diffraction techniques. Longitudinal residual stresses up to eighty percent of the yield strength were observed for the 400 rpm/100 mmpm condition. Increasing the traverse rate while holding the rotational speed fixed increased the residual stress levels in the stir zone and at the stir zone-thermomechanically affected zone interface. The stress profiles displayed the characteristic M shape, and the asymmetry between advancing and retreating stress peaks was limited, occurring mainly on the root side of the weld. The large magnitude of the stresses was maintained throughout the thickness of the plates.

  10. A=20B (1998TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of 20B is predicted to be 69.08 MeV (1974TH01). 20B is then unstable with respect to breakup into 19B + n by 0.9 MeV: see 19B in (1995TI07) and (1978AJ03, 1983ANZQ) and see the...

  11. A=18C (1995TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of the 48Ca(18O, 18C)48Ti reaction. 18C is then bound by 4.188 MeV with respect to breakup into 17C + n. See also (1982FI10, 1987AJ02, 1992WA22). 1. 18C(-)18N Qm 11.807 The...

  12. A=18Na (1995TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    95TI07) (Not observed) 18Na has not been observed; its atomic mass excess has been estimated to be 25.32 MeV (1993AU05); it is then unbound with respect to proton emission by 1.6 MeV: see (1978AJ03). See also (1986AN07) and (1983ANZQ

  13. A=5Be (2002TI10)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2002TI10) (See the Isobar Diagram for 5Be) See also the A = 5 introductory discussion titled A = 5 resonance parameters. The absence of any group structure in the neutron spectrum in the reaction 3He(3He, n)5Be at E(3He) = 18.0 to 26.0 MeV indicates that 5Beg.s

  14. The corrosivity and passivity of sputtered Mg-Ti alloys

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Song, Guang -Ling; Unocic, Kinga A.; Meyer, III, Harry M.; Cakmak, Ercan; Brady, Michael P.; Gannon, Paul E.; Himmer, Phil; Andrews, Quinn

    2015-11-30

    Our study explored the possibility of forming a “stainless” Mg–Ti alloy. The electrochemical behavior of magnetron-sputtered Mg–Ti alloys was measured in a NaCl solution, and the surface films on the alloys were examined by XPS, SEM and TEM. Increased corrosion resistance was observed with increased Ti content in the sputtered Mg–Ti alloys, but passive-like behavior was not reached until the Ti level (atomic %) was higher than the Mg level. Moreover, the surface film that formed on sputtered Mg–Ti based alloys in NaCl solution was thick, discontinuous and non-protective, whereas a thin, continuous and protective Mg and Ti oxide filmmore » was formed on a sputtered Ti–Mg based alloy.« less

  15. The corrosivity and passivity of sputtered Mg-Ti alloys

    SciTech Connect (OSTI)

    Song, Guang -Ling; Unocic, Kinga A.; Meyer, III, Harry M.; Cakmak, Ercan; Brady, Michael P.; Gannon, Paul E.; Himmer, Phil; Andrews, Quinn

    2015-11-30

    Our study explored the possibility of forming a “stainless” Mg–Ti alloy. The electrochemical behavior of magnetron-sputtered Mg–Ti alloys was measured in a NaCl solution, and the surface films on the alloys were examined by XPS, SEM and TEM. Increased corrosion resistance was observed with increased Ti content in the sputtered Mg–Ti alloys, but passive-like behavior was not reached until the Ti level (atomic %) was higher than the Mg level. Moreover, the surface film that formed on sputtered Mg–Ti based alloys in NaCl solution was thick, discontinuous and non-protective, whereas a thin, continuous and protective Mg and Ti oxide film was formed on a sputtered Ti–Mg based alloy.

  16. Structural characterization of the FeTiO{sub 3}-MnTiO{sub 3} solid solution

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect Structural characterization of the FeTiO{sub 3}-MnTiO{sub 3} solid solution Citation Details In-Document Search Title: Structural characterization of the FeTiO{sub 3}-MnTiO{sub 3} solid solution We have synthesized the (Mn{sub 1-x}Fe{sub x})TiO{sub 3} (0.0{<=}x{<=}1.0) solid solution compounds by high-temperature sintered methods, and characterized their crystal structures by combining X-ray diffraction, Moessbauer spectroscopy and Raman

  17. Diameter dependent thermoelectric properties of individual SnTe nanowires

    SciTech Connect (OSTI)

    Xu, E. Z.; Li, Z.; Martinez, J. A.; Sinitsyn, N.; Htoon, H.; Li, Nan; Swartzentruber, B.; Hollingsworth, J. A.; Wang, Jian; Zhang, S. X.

    2015-01-15

    The lead-free compound tin telluride (SnTe) has recently been suggested to be a potentially promising thermoelectric material because of its similar electronic band structure as the well-known lead telluride. Here we report on the first thermoelectric study of individual single crystalline SnTe nanowires (NWs) with different diameters ranging from ~200 to ~1000 nm. Measurements of thermopower S, electrical conductivity σ, and thermal conductivity κ were carried out on the same nanowires over a temperature range of 25 - 300 K. While σ does not show a strong diameter dependence, the thermopower increases by a factor of 2 when the nanowire diameter is decreased from 1000 nm to 200 nm. The thermal conductivities of the measured NWs are only about half of that of the bulk SnTe, which may arise from the enhanced phonon-grain boundary and phonon-defect scatterings. Temperature dependent figure-of-merit ZT was determined and the maximum value at room temperature is ~3 times higher than what was obtained in bulk samples of comparable carrier density.

  18. Diameter dependent thermoelectric properties of individual SnTe nanowires

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Xu, E. Z.; Li, Z.; Martinez, J. A.; Sinitsyn, N.; Htoon, H.; Li, Nan; Swartzentruber, B.; Hollingsworth, J. A.; Wang, Jian; Zhang, S. X.

    2015-01-15

    The lead-free compound tin telluride (SnTe) has recently been suggested to be a potentially promising thermoelectric material because of its similar electronic band structure as the well-known lead telluride. Here we report on the first thermoelectric study of individual single crystalline SnTe nanowires (NWs) with different diameters ranging from ~200 to ~1000 nm. Measurements of thermopower S, electrical conductivity σ, and thermal conductivity κ were carried out on the same nanowires over a temperature range of 25 - 300 K. While σ does not show a strong diameter dependence, the thermopower increases by a factor of 2 when the nanowiremore » diameter is decreased from 1000 nm to 200 nm. The thermal conductivities of the measured NWs are only about half of that of the bulk SnTe, which may arise from the enhanced phonon-grain boundary and phonon-defect scatterings. Temperature dependent figure-of-merit ZT was determined and the maximum value at room temperature is ~3 times higher than what was obtained in bulk samples of comparable carrier density.« less

  19. Quantum oscillations in a two-dimensional electron gas at the rocksalt/zincblende interface of PbTe/CdTe (111) heterostructures.

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Zhang, Bingpo; Lu, Ping; Liu, Henan; Jiao, Lin; Ye, Zhenyu; Jaime, M.; Balakirev, F. F.; Yuan, Huiqiu; Wu, Huizhen; Pan, Wei; et al

    2015-06-05

    Quantum oscillations are observed in the 2DEG system at the interface of novel heterostructures, PbTe/CdTe (111), with nearly identical lattice parameters (aPbTe = 0.6462 nm, aCdTe = 0.648 nm) but very different lattice structures (PbTe: rock salt, CdTe: zinc blende). The 2DEG formation mechanism, a mismatch in the bonding configurations of the valence electrons at the interface, is uniquely different from the other known 2DEG systems. The aberration-corrected scanning transmission electron microscope (AC-STEM) characterization indicates an abrupt interface without cation interdiffusion due to a large miscibility gap between the two constituent materials. As a result, electronic transport measurements under magneticmore » field up to 60 T, with the observation of Landau level filling factor ν = 1, unambiguously reveal a π Berry phase, suggesting the Dirac Fermion nature of the 2DEG at the heterostructure interface, and the PbTe/CdTe heterostructure being a new candidate for 2D topological crystalline insulators.« less

  20. Quantum oscillations in a two-dimensional electron gas at the rocksalt/zincblende interface of PbTe/CdTe (111) heterostructures.

    SciTech Connect (OSTI)

    Zhang, Bingpo; Lu, Ping; Liu, Henan; Jiao, Lin; Ye, Zhenyu; Jaime, M.; Balakirev, F. F.; Yuan, Huiqiu; Wu, Huizhen; Pan, Wei; Zhang, Yong

    2015-06-05

    Quantum oscillations are observed in the 2DEG system at the interface of novel heterostructures, PbTe/CdTe (111), with nearly identical lattice parameters (aPbTe = 0.6462 nm, aCdTe = 0.648 nm) but very different lattice structures (PbTe: rock salt, CdTe: zinc blende). The 2DEG formation mechanism, a mismatch in the bonding configurations of the valence electrons at the interface, is uniquely different from the other known 2DEG systems. The aberration-corrected scanning transmission electron microscope (AC-STEM) characterization indicates an abrupt interface without cation interdiffusion due to a large miscibility gap between the two constituent materials. As a result, electronic transport measurements under magnetic field up to 60 T, with the observation of Landau level filling factor ν = 1, unambiguously reveal a π Berry phase, suggesting the Dirac Fermion nature of the 2DEG at the heterostructure interface, and the PbTe/CdTe heterostructure being a new candidate for 2D topological crystalline insulators.

  1. Effect of neutron irradiation on defect evolution in Ti3SiC2 and Ti2AlC

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Tallman, Darin J.; He, Lingfeng; Garcia-Diaz, Brenda L.; Hoffman, Elizabeth N.; Kohse, Gordon; Sindelar, Robert L.; Barsoum, Michel W.

    2015-10-23

    Here, we report on the characterization of defects formed in polycrystalline Ti3SiC2 and Ti2AlC samples exposed to neutron irradiation – up to 0.1 displacements per atom (dpa) at 350 ± 40 °C or 695 ± 25 °C, and up to 0.4 dpa at 350 ± 40 °C. Black spots are observed in both Ti3SiC2 and Ti2AlC after irradiation to both 0.1 and 0.4 dpa at 350 °C. After irradiation to 0.1 dpa at 695 °C, small basal dislocation loops, with a Burgers vector of b = 1/2 [0001] are observed in both materials. At 9 ± 3 and 10 ±more » 5 nm, the loop diameters in the Ti3SiC2 and Ti2AlC samples, respectively, were comparable. At 1 × 1023 loops/m3, the dislocation loop density in Ti2AlC was ≈1.5 orders of magnitude greater than in Ti3SiC2, at 3 x 1021 loops/m3. After irradiation at 350 °C, extensive microcracking was observed in Ti2AlC, but not in Ti3SiC2. The room temperature electrical resistivities increased as a function of neutron dose for all samples tested, and appear to saturate in the case of Ti3SiC2. The MAX phases are unequivocally more neutron radiation tolerant than the impurity phases TiC and Al2O3. Based on these results, Ti3SiC2 appears to be a more promising MAX phase candidate for high temperature nuclear applications than Ti2AlC.« less

  2. Dynamic conductivity of the bulk states of n-type HgTe/CdTe quantum well topological insulator

    SciTech Connect (OSTI)

    Chen, Qinjun; Sanderson, Matthew; Cao, J. C.; Zhang, Chao

    2014-11-17

    We theoretically studied the frequency-dependent current response of the bulk state of topological insulator HgTe/CdTe quantum well. The optical conductivity is mainly due to the inter-band process at high frequencies. At low frequencies, intra-band process dominates with a dramatic drop to near zero before the inter-band contribution takes over. The conductivity decreases with temperature at low temperature and increases with temperature at high temperature. The transport scattering rate has an opposite frequency dependence in the low and high temperature regime. The different frequency dependence is due to the interplay of the carrier-impurity scattering and carrier population near the Fermi surface.

  3. Structural and Morphological Difference Between Ti/TiN/TiCN Coatings Grown in Multilayer and Graded Form

    SciTech Connect (OSTI)

    Restrepo, E.; Baena, A.; Agudelo, C.; Castillo, H.; Devia, A.; Marino, A.

    2006-12-04

    Thin films can be grown in super-lattice, multilayers and graded form, having each one advantages and disadvantages. The difference between multilayer and graded coatings is the interface. In multilayers the interface is abrupt and in graded coatings it is diffuse. The interface influences many chemical and physical properties of the materials, and its choice depends on the application. Graded coatings have the advantage of having gradual properties such as thermal expansion coefficient and lattice parameter, avoiding adherence problems due to good match between their component materials. In this work the comparison between some properties of coatings grown as multilayer and graded is performed. The materials are produced using the sputtering DC technique because of its facility to control the deposition parameters and generate a slow growth. The target is a disc of titanium and the samples are made of stainless steel 304. The working gases are argon, nitrogen and methane, which are mixed according to the material to be produced, i.e. Ti layer is grown with argon, the TiN film is produced with a mixture of argon and nitrogen, and the TiCN material is obtained mixing argon, nitrogen and methane. These materials are characterized with AFM in order to determine grain size and with XPS studying the chemical composition and performing depth profiles.

  4. Post-Growth Annealing of Bridgman-grown CdZnTe and CdMnTe Crystals for Room-temperature Nuclear Radiation Detectors

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Egarievwe, Stephen U.; Yang, Ge; Egarievwe, Alexander; Okwechime, Ifechukwude O.; Gray, Justin; Hales, Zaveon M.; Hossain, Anwar; Camarda, Guiseppe S.; Bolotnikov, Aleksey E.; James, Ralph B.

    2015-02-11

    Bridgman-grown cadmium zinc telluride (CdZnTe or CZT) and cadmium manganese telluride (CdMnTe or CMT) crystals often have Te inclusions that limit their performances as X-ray- and gamma-ray-detectors. We present here the results of post-growth thermal annealing aimed at reducing and eliminating Te inclusions in them. In a 2D analysis, we observed that the sizes of the Te inclusions declined to 92% during a 60-h annealing of CZT at 510 °C under Cd vapor. Further, tellurium inclusions were eliminated completely in CMT samples annealed at 570 °C in Cd vapor for 26 h, whilst their electrical resistivity fell by an ordermore » of 102. During the temperature-gradient annealing of CMT at 730 °C and an 18 °C/cm temperature gradient for 18 h in a vacuum of 10-5 mbar, we observed the diffusion of Te from the sample, causing a reduction in size of the Te inclusions. For CZT samples annealed at 700 °C in a 10 °C/cm temperature gradient, we observed the migration of Te inclusions from a low-temperature region to a high one at 0.022 μm/s. During the temperature-gradient annealing of CZT in a vacuum of 10-5 mbar at 570 °C and 30 °C/cm for 18 h, some Te inclusions moved toward the high-temperature side of the wafer, while other inclusions of the same size, i.e., 10 µm in diameter, remained in the same position. These results show that the migration, diffusion, and reaction of Te with Cd in the matrix of CZT- and CMT-wafers are complex phenomena that depend on certain conditions.« less

  5. Polytypism, polymorphism, and superconductivity in TaSe2–xTex

    SciTech Connect (OSTI)

    Luo, Huixia; Xie, Weiwei; Tao, Jing; Inoue, Hiroyuki; Gyenis, András; Krizan, Jason W.; Yazdani, Ali; Zhu, Yimei; Cava, Robert Joseph

    2015-03-03

    Polymorphism in materials often leads to significantly different physical properties - the rutile and anatase polymorphs of TiO₂ are a prime example. Polytypism is a special type of polymorphism, occurring in layered materials when the geometry of a repeating structural layer is maintained but the layer stacking sequence of the overall crystal structure can be varied; SiC is an example of a material with many polytypes. Although polymorphs can have radically different physical properties, it is much rarer for polytypism to impact physical properties in a dramatic fashion. Here we study the effects of polytypism and polymorphism on the superconductivity of TaSe₂, one of the archetypal members of the large family of layered dichalcogenides. We show that it is possible to access 2 stable polytypes and 2 stable polymorphs in the TaSe2-xTex solid solution, and find that the 3R polytype shows a superconducting transition temperature that is between 6 and 17 times higher than that of the much more commonly found 2H polytype. Thus, the reason for this dramatic change is not apparent, but we propose that it arises either from a remarkable dependence of Tc on subtle differences in the characteristics of the single layers present, or from a surprising effect of the layer stacking sequence on electronic properties that instead are expected to be dominated by the properties of a single layer in materials of this kind.

  6. A W' boson near 2 TeV: Predictions for run 2 of the LHC

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Dobrescu, Bogdan A.; Liu, Zhen

    2015-11-20

    We present a renormalizable theory that includes a W' boson of mass in the 1.8–2 TeV range, which may explain the excess events reported by the ATLAS Collaboration in a WZ final state, and by the CMS Collaboration in e+e– jj, Wh0, and jj final states. The W' boson couples to right-handed quarks and leptons, including Dirac neutrinos with TeV-scale masses. This theory predicts a Z' boson of mass in the 3.4–4.5 TeV range. The cross section times branching fractions for the narrow Z' dijet and dilepton peaks at the 13 TeV LHC are 10 and 0.6 fb, respectively, formore » MZ'=3.4 TeV, and an order of magnitude smaller for MZ'=4.5 TeV.« less

  7. Charge transfer and mobility enhancement at CdO/SnTe heterointerfaces

    SciTech Connect (OSTI)

    Nishitani, Junichi; Yu, Kin Man; Walukiewicz, Wladek

    2014-09-29

    We report a study of the effects of charge transfer on electrical properties of CdO/SnTe heterostructures. A series of structures with variable SnTe thicknesses were deposited by RF magnetron sputtering. Because of an extreme type III band offset with the valence band edge of SnTe located at 1.5?eV above the conduction band edge of CdO, a large charge transfer is expected at the interface of the CdO/SnTe heterostructure. The electrical properties of the heterostructures are analyzed using a multilayer charge transport model. The analysis indicates a large 4-fold enhancement of the CdO electron mobility at the interface with SnTe. The mobility enhancement is attributed to reduction of the charge center scattering through neutralization of the donor-like defects responsible for the Fermi level pinning at the CdO/SnTe interface.

  8. The Effect of Structural Vacancies on the Thermoelectric Properties of (Cu2Te)1-x(Ga2Te3)x

    SciTech Connect (OSTI)

    Ye, Zuxin; Cho, Jung Y; Tessema, Misle; Salvador, James R.; Waldo, Richard; Wang, Hsin; Cai, Wei

    2013-01-01

    We have studied the effects of structural vacancies on the thermoelectric properties of the ternary compounds (Cu2Te)1-x(Ga2Te3)x (x = 0.5, 0.55, 0.571, 0.6, 0.625, 0.667 and 0.75), which are solid solutions found in the pseudo-binary phase diagram for Cu2Te and Ga2Te3. This system possesses tunable structural vacancy concentrations. The x= 0.5 phase, CuGaTe2, is nominally devoid of structural vacancies, while the rest of the compounds contain varying amounts of these features, and the volume density of vacancies increases with Ga2Te3 content. The sample with x = 0.5, 0.55, 0.571, 0.6, 0.625 crystallize in the chalcopyrite structure while the x = 0.667 and 0.75 adopt the Ga2Te3 defect zinc blende structure. Strong scattering of heat carrying phonons by structural defects, leads to the reduction of thermal conductivity, which is beneficial to the thermoelectric performance of materials. On the other hand, these defects also scatter charge carriers and reduce the electrical conductivity. All the samples investigated are p-type semiconductors as inferred by the signs of their respective Hall (RH) and Seebeck (S) coefficients. The structural vacancies were found to scatter phonons strongly, while a combination of increased carrier concentration, and vacancies decreases the Hall mobility ( H), degrading the overall thermoelectric performance. The room temperature H drops from 90 cm2/V s for CuGaTe2 to 13 cm2/V s in Cu9Ga11Te21 and 4.6 cm2/V s in CuGa3Te5. The low temperature thermal conductivity decreases significantly with higher Ga2Te3 concentrations (higher vacancy concentration) due to increased point defect scattering which dominate thermal resistance terms. At high temperatures, the dependence of thermal conductivity on the Ga2Te3 content is less significant. The presence of strong Umklapp scattering leads to low thermal conductivity at high temperatures for all samples investigated. The highest ZT among the samples in this study was found for the defect-free CuGaTe2 with ZT ~ 1.0 at 840K.

  9. Photoluminescence Imaging of Large-Grain CdTe for Grain Boundary

    Office of Scientific and Technical Information (OSTI)

    Characterization (Conference) | SciTech Connect Photoluminescence Imaging of Large-Grain CdTe for Grain Boundary Characterization Citation Details In-Document Search Title: Photoluminescence Imaging of Large-Grain CdTe for Grain Boundary Characterization In this work, we use photoluminescence (PL) imaging to characterize CdTe grain boundary recombination. We use a silicon megapixel camera and green (532 nm) laser diodes for excitation. A microscope objective lens system is used for high

  10. Component Overpressure Growth and Characterization of High Resistivity CdTe

    Office of Scientific and Technical Information (OSTI)

    Crystals for Radiation Detectors (Journal Article) | SciTech Connect Component Overpressure Growth and Characterization of High Resistivity CdTe Crystals for Radiation Detectors Citation Details In-Document Search Title: Component Overpressure Growth and Characterization of High Resistivity CdTe Crystals for Radiation Detectors Spectrometer-grade CdTe single crystals with resistivities higher than 10{sup 9} {Omega} cm have been grown by the modified Bridgman method using zone-refined

  11. High Efficiency Single Crystal CdTe Solar Cells: November 19, 2009 - January 31, 2011

    SciTech Connect (OSTI)

    Carmody, M.; Gilmore, A.

    2011-05-01

    The goal of the program was to develop single crystal CdTe-based top cells grown on Si solar cells as a platform for the subsequent manufacture of high efficiency tandem cells for CPV applications. The keys to both the single junction and the tandem junction cell architectures are the ability to grow high quality single-crystal CdTe and CdZnTe layers on p-type Si substrates, to dope the CdTe and CdZnTe controllably, both n and p-type, and to make low resistance ohmic front and back contacts. EPIR demonstrated the consistent MBE growth of CdTe/Si and CdZnTe/Si having high crystalline quality despite very large lattice mismatches; epitaxial CdTe/Si and CdZnTe/Si consistently showed state-of-the-art electron mobilities and good hole mobilities; bulk minority carrier recombination lifetimes of unintentionally p-doped CdTe and CdZnTe grown by MBE on Si were demonstrated to be consistently of order 100 ns or longer; desired n- and p-doping levels were achieved; solar cell series specific resistances <10 ?-cm2 were achieved; A single-junction solar cell having a state-of-the-art value of Voc and a unverified 16.4% efficiency was fabricated from CdZnTe having a 1.80 eV bandgap, ideal for the top junction in a tandem cell with a Si bottom junction.

  12. Microstructure and Thermoelectric Properties of Mechanically Robust PbTe-Si

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Eutectic Composites | Energy Frontier Research Centers Microstructure and Thermoelectric Properties of Mechanically Robust PbTe-Si Eutectic Composites Home Author: J. R. Sootsman, J. He, V. P. Dravid, S. Ballikaya, D. Vermeulen, C. Uher, M. G. Kanatzidis Year: 2010 Abstract: The microstructure and thermoelectric properties of the PbTe-Si eutectic system are presented in detail. When rapidly quenched from the melt this system yields materials with thermoelectric properties similar to PbTe

  13. A Review Corrosion of TI Grade 7 and Other TI Alloys in Nuclear Waste Repository Environments

    SciTech Connect (OSTI)

    F. Hua; K. Mon; P. Pasupathi; G. Gordon

    2004-05-11

    Titanium alloy degradation modes are reviewed in relation to their performance in repository environments. General corrosion, localized corrosion, stress corrosion cracking, hydrogen induced cracking, microbially influenced corrosion, and radiation-assisted corrosion of Ti alloys are considered. With respect to the Ti Grade 7 drip shields selected for emplacement in the repository at Yucca Mountain, general corrosion, hydrogen induced cracking, and radiation-assisted corrosion will not lead to failure within the 10,000 year regulatory period; stress corrosion cracking (in the absence of disruptive events) is of no consequence to barrier performance; and localized corrosion and microbially influenced corrosion are not expected to occur. To facilitate the discussion, Ti Grades 2, 5, 7, 9, 11, 12, 16, 17, 18, and 24 are included in this review.

  14. Nature of Transactions (TI) Code | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Nature of Transactions (TI) Code U.S. Department of Energy / U.S. Nuclear Regulatory Commission Nuclear Materials Management & Safeguards System Nature of Transactions (TI) Code* Nature of Transactions (TI) Code* Code: Description: A Initiates lease and financial responsibility of DOE-owned material B Transfer of lease and financial responsiblity of DOE-owned material C Transfer of DOE-owned material with no change in lease or financial responsibility D Return to DOE for credit under DOE

  15. High Efficiency CdTe and CIGS Thin Film Solar Cells: Highlights...

    Office of Scientific and Technical Information (OSTI)

    High Efficiency CdTe and CIGS Thin Film Solar Cells: Highlights of the Technologies Challenges Acknowledgement: Work performed at NREL for US DOE under contract No....

  16. Analysis of Surface Chemistry and Detector Performance of Chemically Process CdZnTe crystals

    SciTech Connect (OSTI)

    HOSSAIN A.; Yang, G.; Sutton, J.; Zergaw, T.; Babalola, O. S.; Bolotnikov, A. E.; Camarda. ZG. S.; Gul, R.; Roy, U. N., and James, R. B.

    2015-10-05

    The goal is to produce non-conductive smooth surfaces for fabricating low-noise and high-efficiency CdZnTe devices.

  17. Nanoscale imaging of photocurrent and efficiency in CdTe solar...

    Office of Scientific and Technical Information (OSTI)

    cells The local collection characteristics of grain interiors and grain boundaries in thin film CdTe polycrystalline solar cells are investigated using scanning photocurrent...

  18. Characterization and Analysis of CIGS and CdTE Solar Cells: December 2004 - July 2008

    SciTech Connect (OSTI)

    Sites, J. R.

    2009-01-01

    The work reported here embodies a device-physics approach based on careful measurement and interpretation of data from CIGS and CdTe solar cells.

  19. Scandium resonant impurity level in PbTe

    SciTech Connect (OSTI)

    Skipetrov, E. P. Skipetrova, L. A.; Knotko, A. V.; Slynko, E. I.; Slynko, V. E.

    2014-04-07

    We synthesize a scandium-doped PbTe single-crystal ingot and investigate the phase and the elemental composition as well as galvanomagnetic properties of Pb{sub 1-y}Sc{sub y}Te alloys in weak magnetic fields (4.2?K???T???300?K, B???0.07?T) upon varying the scandium content (y???0.02). We find that all investigated samples are single-phase and n-type. The distribution of scandium impurities along the axis of the ingot is estimated to be exponential. An increase of scandium impurity content leads to a monotonous growth of the free electron concentration by four orders of magnitude (approximately from 10{sup 16}?cm{sup ?3} to 10{sup 20}?cm{sup ?3}). In heavily doped alloys (y?>?0.01), the free electron concentration at the liquid-helium temperature tends to saturation, indicating the pinning of the Fermi energy by the scandium resonant impurity level located on the background of the conduction band. Using the two-band Kane and six-band Dimmock dispersion relations for IV-VI semiconductors, dependences of the Fermi energy measured from the bottom of the conduction band E{sub c} on the scandium impurity content are calculated and the energy of the resonant scandium level is estimated to be E{sub Sc}???E{sub c}?+?280?meV. Diagrams of electronic structure rearrangement of Pb{sub 1-y}Sc{sub y}Te alloys upon doping are proposed.

  20. Thermoelastic Analysis of a Vibrating TiB/Ti Cantilever Beam Using Differential Thermography

    SciTech Connect (OSTI)

    Byrd, Larry; Wyen, Travis; Byrd, Alex

    2008-02-15

    Differential thermography has been used to detect the fluctuating temperatures due the thermoelastic effect for a number of years. This paper examines functionally graded TiB/Ti cantilever beams excited on an electromechanical shaker in fully reversed bending. Finite difference analysis of specimens was used to look at the effect of heat conduction, convection and the fundamental frequency on the surface temperature distribution and compared to experimental data. The thermoelastic effect was also used to detect cracking and the stress field at the tip of the fixture during fatigue.

  1. Ab initio Study of He Stability in hcp-Ti

    SciTech Connect (OSTI)

    Dai, Yunya; Yang, Li; Peng, SM; Long, XG; Gao, Fei; Zu, Xiaotao T.

    2010-12-20

    The stability of He in hcp-Ti was studied using ab initio method based on density functional theory. The results indicate that a single He atom prefers to occupy the tetrahedral site rather than the octahedral site. The interaction of He defects with Ti atoms has been used to explain the relative stabilities of He point defects in hcp-Ti. The relative stability of He defects in hcp-Ti is useful for He clustering and bubble nucleation in metal tritides, which provides the basis for development of improved atomistic models.

  2. Cathodic cage plasma deposition of TiN and TiO{sub 2} thin films on silicon substrates

    SciTech Connect (OSTI)

    Sousa, Romulo R. M. de; Sato, Patricia S.; Nascente, Pedro A. P.; Viana, Bartolomeu C.; Alves, Clodomiro; Nishimoto, Akio

    2015-07-15

    Cathodic cage plasma deposition (CCPD) was used for growing titanium nitride (TiN) and titanium dioxide (TiO{sub 2}) thin films on silicon substrates. The main advantages of the CCPD technique are the uniformity, tridimensionality, and high rate of the film deposition that occurs at higher pressures, lower temperatures, and lower treatment times than those used in conventional nitriding treatments. In this work, the influence of the temperature and gas atmosphere upon the characteristics of the deposited films was investigated. The TiN and TiO{sub 2} thin films were characterized by x-ray diffraction, scanning electron microscopy, and Raman spectroscopy to analyze their chemical, structural, and morphological characteristics, and the combination of these results indicates that the low-cost CCPD technique can be used to produce even and highly crystalline TiN and TiO{sub 2} films.

  3. High-Efficiency, Commercial Ready CdTe Solar Cells

    SciTech Connect (OSTI)

    Sites, James R.

    2015-11-19

    Colorado State’s F-PACE project explored several ways to increase the efficiency of CdTe solar cells and to better understand the device physics of those cells under study. Increases in voltage, current, and fill factor resulted in efficiencies above 17%. The three project tasks and additional studies are described in detail in the final report. Most cells studied were fabricated at Colorado State using an industry-compatible single-vacuum closed-space-sublimation (CSS) chamber for deposition of the key semiconductor layers. Additionally, some cells were supplied by First Solar for comparison purposes, and a small number of modules were supplied by Abound Solar.

  4. Mr. John E. Kieling, Chief Hazardous Was te Bureau

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    John E. Kieling, Chief Hazardous Was te Bureau Depa rtment of Energy Carlsbad Field Office P. O. Box 3090 Carlsbad , New Mexico 88221 NOV 0 5 2013 New Mexico Environment Department 2905 Rodeo Park Drive East. Building 1 Santa Fe, New Mexico 87505-6303 Subject: Panel 6 Closure and Final Waste Emplacement Notifications Dear Mr. Kieling : The purpose of this leiter is 1 0 notify th e New Mexico Environment Department (NMEO) that the Permittees intend to commence closure of Hazardous Waste Disposa

  5. Characterization of Residual Stress as a Function of Friction Stir Welding Parameters in Oxide Dispersion Strengthened (ODS) Steel MA956

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Brewer, Luke N.; Bennett, Martin S.; Baker, B. W.; Payzant, E. Andrew; Kolbus, Lindsay M.

    2015-09-08

    This article characterizes the residual stresses generated by friction stir welding of oxide dispersion strengthened steel MA956 over a series of welding conditions. A plate of MA956 steel was friction stir welded at three conditions: 500 rpm/25 millimeters per minute (mmpm), 400 rpm/50 mmpm and 400 rpm/100 mmpm. The residual stresses across these welds were measured using both x-ray and neutron diffraction techniques. Longitudinal residual stresses up to eighty percent of the yield strength were observed for the 400 rpm/100 mmpm condition. Increasing the traverse rate while holding the rotational speed fixed increased the residual stress levels in the stirmore » zone and at the stir zone-thermomechanically affected zone interface. The stress profiles displayed the characteristic M shape, and the asymmetry between advancing and retreating stress peaks was limited, occurring mainly on the root side of the weld. The large magnitude of the stresses was maintained throughout the thickness of the plates.« less

  6. Magnetic Hardening of CeFe11Ti and the Effect of TiC Addition (Journal

    Office of Scientific and Technical Information (OSTI)

    Article) | SciTech Connect Magnetic Hardening of CeFe11Ti and the Effect of TiC Addition Citation Details In-Document Search Title: Magnetic Hardening of CeFe11Ti and the Effect of TiC Addition Authors: Zhou, Chen ; Haddad, Daad ; Kukreja, Ratandeep S. ; Pinkerton, Frederick E. ; Sun, Kewei ; Kramer, M. J. Publication Date: 2015-04-01 OSTI Identifier: 1221660 Report Number(s): IS-J 8423 Journal ID: ISSN 0018-9464 DOE Contract Number: AC02-07CH11358; 0472-1526 Resource Type: Journal Article

  7. Role of double Ti O 2 layers at the interface of FeSe/ SrTi O 3

    Office of Scientific and Technical Information (OSTI)

    superconductors (Journal Article) | SciTech Connect SciTech Connect Search Results Journal Article: Role of double Ti O 2 layers at the interface of FeSe/ SrTi O 3 superconductors Citation Details In-Document Search This content will become publicly available on May 16, 2017 Title: Role of double Ti O 2 layers at the interface of FeSe/ SrTi O 3 superconductors Authors: Zou, Ke ; Mandal, Subhasish ; Albright, Stephen D. ; Peng, Rui ; Pu, Yujia ; Kumah, Divine ; Lau, Claudia ; Simon, Georg H.

  8. Role of double Ti O 2 layers at the interface of FeSe/ SrTi O 3

    Office of Scientific and Technical Information (OSTI)

    superconductors (Journal Article) | DOE PAGES Publisher's Accepted Manuscript: Role of double Ti O 2 layers at the interface of FeSe/ SrTi O 3 superconductors This content will become publicly available on May 16, 2017 « Prev Next » Title: Role of double Ti O 2 layers at the interface of FeSe/ SrTi O 3 superconductors Authors: Zou, Ke ; Mandal, Subhasish ; Albright, Stephen D. ; Peng, Rui ; Pu, Yujia ; Kumah, Divine ; Lau, Claudia ; Simon, Georg H. ; Dagdeviren, Omur E. ; He, Xi ;

  9. High-performance symmetric sodium-ion batteries using a new, bipolar O3-type material, Na 0.8 Ni 0.4 Ti 0.6 O 2

    SciTech Connect (OSTI)

    Guo, Shaohua; Yu, Haijun; Liu, Pan; Ren, Yang; Zhang, Tao; Chen, Mingwei; Ishida, Masayoshi; Zhou, Haoshen

    2015-01-01

    Based on low-cost and rich resources, sodium-ion batteries have been regarded as a promising candidate for next-generation energy storage batteries in the large-scale energy applications of renewable energy and smart grids. However, there are some critical drawbacks limiting its application, such as safety and stability problems. In this work, a stable symmetric sodium-ion battery based on the bipolar, active O3-type material, Na0.8Ni0.4Ti0.6O2, is developed. This bipolar material shows a typical O3-type layered structure, containing two electrochemically active transition metals with redox couples of Ni4+/Ni2+ and Ti4+/Ti3+, respectively. This Na0.8Ni0.4Ti0.6O2-based symmetric cell exhibits a high average voltage of 2.8 V, a reversible discharge capacity of 85 mA h g(-1), 75% capacity retention after 150 cycles and good rate capability. This full symmetric cell will greatly contribute to the development of room-temperature sodium-ion batteries with a view towards safety, low cost and long life, and it will stimulate further research on symmetric cells using the same active materials as both cathode and anode.

  10. Structure-Curie temperature relationships in BaTiO 3 -based ferroelect...

    Office of Scientific and Technical Information (OSTI)

    ferroelectric perovskites: Anomalous behavior of ( Ba , Cd ) TiO 3 from DFT, ... ferroelectric perovskites: Anomalous behavior of ( Ba , Cd ) TiO 3 from DFT, ...

  11. Influence of carbon content on the copper-telluride phase formation and on the resistive switching behavior of carbon alloyed Cu-Te conductive bridge random access memory cells

    SciTech Connect (OSTI)

    Devulder, Wouter De Schutter, Bob; Detavernier, Christophe; Opsomer, Karl; Franquet, Alexis; Meersschaut, Johan; Muller, Robert; Van Elshocht, Sven; Jurczak, Malgorzata; Goux, Ludovic; Belmonte, Attilio

    2014-02-07

    In this paper, we investigate the influence of the carbon content on the Cu-Te phase formation and on the resistive switching behavior in carbon alloyed Cu{sub 0.6}Te{sub 0.4} based conductive bridge random access memory (CBRAM) cells. Carbon alloying of copper-tellurium inhibits the crystallization, while attractive switching behavior is preserved when using the material as Cu-supply layer in CBRAM cells. The phase formation is first investigated in a combinatorial way. With increasing carbon content, an enlargement of the temperature window in which the material stays amorphous was observed. Moreover, if crystalline phases are formed, subsequent phase transformations are inhibited. The electrical switching behavior of memory cells with different carbon contents is then investigated by implementing them in 580 μm diameter dot TiN/Cu{sub 0.6}Te{sub 0.4}-C/Al{sub 2}O{sub 3}/Si memory cells. Reliable switching behavior is observed for carbon contents up to 40 at. %, with a resistive window of more than 2 orders of magnitude, whereas for 50 at. % carbon, a higher current in the off state and only a small resistive window are present after repeated cycling. This degradation can be ascribed to the higher thermal and lower drift contribution to the reset operation due to a lower Cu affinity towards the supply layer, leading cycle-after-cycle to an increasing amount of Cu in the switching layer, which contributes to the current. The thermal diffusion of Cu into Al{sub 2}O{sub 3} under annealing also gives an indication of the Cu affinity of the source layer. Time of flight secondary ion mass spectroscopy was used to investigate this migration depth in Al{sub 2}O{sub 3} before and after annealing, showing a higher Cu, Te, and C migration for high carbon contents.

  12. Extending Higgs inflation with TeV scale new physics

    SciTech Connect (OSTI)

    He, Hong-Jian; Xianyu, Zhong-Zhi E-mail: xianyuzhongzhi@gmail.com

    2014-10-01

    Higgs inflation is among the most economical and predictive inflation models, although the original Higgs inflation requires tuning the Higgs or top mass away from its current experimental value by more than 2? deviations, and generally gives a negligible tensor-to-scalar ratio r?10{sup -3} (if away from the vicinity of critical point). In this work, we construct a minimal extension of Higgs inflation, by adding only two new weak-singlet particles at TeV scale, a vector-quark T and a real scalar S. The presence of singlets (T,S) significantly impact the renormalization group running of the Higgs boson self-coupling. With this, our model provides a wider range of the tensor-to-scalar ratio r=O(0.1)-O(10{sup -3}), consistent with the favored r values by either BICEP2 or Planck data, while keeping the successful prediction of the spectral index n{sub s}?0.96. It allows the Higgs and top masses to fully fit the collider measurements. We also discuss implications for searching the predicted TeV-scale vector-quark T and scalar S at the LHC and future high energy pp colliders.

  13. Extending Higgs inflation with TeV scale new physics

    SciTech Connect (OSTI)

    He, Hong-Jian; Xianyu, Zhong-Zhi

    2014-10-10

    Higgs inflation is among the most economical and predictive inflation models, although the original Higgs inflation requires tuning the Higgs or top mass away from its current experimental value by more than 2σ deviations, and generally gives a negligible tensor-to-scalar ratio r∼10{sup −3} (if away from the vicinity of critical point). In this work, we construct a minimal extension of Higgs inflation, by adding only two new weak-singlet particles at TeV scale, a vector-quark T and a real scalar S . The presence of singlets (T, S) significantly impact the renormalization group running of the Higgs boson self-coupling. With this, our model provides a wider range of the tensor-to-scalar ratio r=O(0.1)−O(10{sup −3}) , consistent with the favored r values by either BICEP2 or Planck data, while keeping the successful prediction of the spectral index n{sub s}≃0.96 . It allows the Higgs and top masses to fully fit the collider measurements. We also discuss implications for searching the predicted TeV-scale vector-quark T and scalar S at the LHC and future high energy pp colliders.

  14. Purification of CdZnTe by Electromigration

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Kim, K.; Kim, Sangsu; Hong, Jinki; Lee, Jinseo; Hong, Taekwon; Bolotnikov, A. E.; Camarda, G. S.; James, R. B.

    2015-04-14

    Electro-migration of ionized/electrically active impurities in CdZnTe (CZT) was successfully demonstrated at elevated temperature with an electric field of 20 V/mm. Copper, which exists in positively charged states, electro-migrated at a speed of 15 lm/h in an electric field of 20 V/mm. A notable variation in impurity concentration along the growth direction with the segregation tendency of the impurities was observed in an electro-migrated CZT boule. Notably, both Ga and Fe, which exist in positively charged states, exhibited the opposite distribution to that of their segregation tendency in Cd(Zn)Te. Furthermore, a CZT detector fabricated from the middle portion of themore » electromigrated CZT boule showed an improved mobility-lifetime product of 0.91 10-2 cm2 /V, compared to that of 1.4 10-3 cm2 /V, observed in an as-grown (non-electro-migrated) CZT detector. The optimum radiation detector material would have minimum concentration of deep traps required for compensation.« less

  15. Thermodynamic properties of model CdTe/CdSe mixtures

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    van Swol, Frank; Zhou, Xiaowang W.; Challa, Sivakumar R.; Martin, James E.

    2015-02-20

    We report on the thermodynamic properties of binary compound mixtures of model groups II–VI semiconductors. We use the recently introduced Stillinger–Weber Hamiltonian to model binary mixtures of CdTe and CdSe. We use molecular dynamics simulations to calculate the volume and enthalpy of mixing as a function of mole fraction. The lattice parameter of the mixture closely follows Vegard's law: a linear relation. This implies that the excess volume is a cubic function of mole fraction. A connection is made with hard sphere models of mixed fcc and zincblende structures. We found that the potential energy exhibits a positive deviation frommore » ideal soluton behaviour; the excess enthalpy is nearly independent of temperatures studied (300 and 533 K) and is well described by a simple cubic function of the mole fraction. Using a regular solution approach (combining non-ideal behaviour for the enthalpy with ideal solution behaviour for the entropy of mixing), we arrive at the Gibbs free energy of the mixture. The Gibbs free energy results indicate that the CdTe and CdSe mixtures exhibit phase separation. The upper consolute temperature is found to be 335 K. Finally, we provide the surface energy as a function of composition. Moreover, it roughly follows ideal solution theory, but with a negative deviation (negative excess surface energy). This indicates that alloying increases the stability, even for nano-particles.« less

  16. Advanced CdTe Photovoltaic Technology: September 2007 - March 2009

    SciTech Connect (OSTI)

    Barth, K.

    2011-05-01

    During the last eighteen months, Abound Solar (formerly AVA Solar) has enjoyed significant success under the SAI program. During this time, a fully automated manufacturing line has been developed, fabricated and commissioned in Longmont, Colorado. The facility is fully integrated, converting glass and semiconductor materials into complete modules beneath its roof. At capacity, a glass panel will enter the factory every 10 seconds and emerge as a completed module two hours later. This facility is currently undergoing trials in preparation for large volume production of 120 x 60 cm thin film CdTe modules. Preceding the development of the large volume manufacturing capability, Abound Solar demonstrated long duration processing with excellent materials utilization for the manufacture of high efficiency 42 cm square modules. Abound Solar prototype modules have been measured with over 9% aperture area efficiency by NREL. Abound Solar demonstrated the ability to produce modules at industry leading low costs to NREL representatives. Costing models show manufacturing costs below $1/Watt and capital equipment costs below $1.50 per watt of annual manufacturing capacity. Under this SAI program, Abound Solar supported a significant research and development program at Colorado State University. The CSU team continues to make progress on device and materials analysis. Modeling for increased device performance and the effects of processing conditions on properties of CdTe PV were investigated.

  17. Equation of State Model Quality Study for Ti and Ti64.

    SciTech Connect (OSTI)

    Wills, Ann Elisabet; Sanchez, Jason James

    2015-02-01

    Titanium and the titanium alloy Ti64 (6% aluminum, 4% vanadium and the balance ti- tanium) are materials used in many technologically important applications. To be able to computationally investigate and design these applications, accurate Equations of State (EOS) are needed and in many cases also additional constitutive relations. This report describes what data is available for constructing EOS for these two materials, and also describes some references giving data for stress-strain constitutive models. We also give some suggestions for projects to achieve improved EOS and constitutive models. In an appendix, we present a study of the 'cloud formation' issue observed in the ALEGRA code. This issue was one of the motivating factors for this literature search of available data for constructing improved EOS for Ti and Ti64. However, the study shows that the cloud formation issue is only marginally connected to the quality of the EOS, and, in fact, is a physical behavior of the system in question. We give some suggestions for settings in, and improvements of, the ALEGRA code to address this computational di culty.

  18. Photoconductivity of CdTe Nanocrystal-Based Thin Films. Te2- Ligands Lead To Charge Carrier Diffusion Lengths Over 2 Micrometers

    SciTech Connect (OSTI)

    Crisp, Ryan W.; Callahan, Rebecca; Reid, Obadiah G.; Dolzhnikov, Dmitriy S.; Talapin, Dmitri V.; Rumbles, Garry; Luther, Joseph M.; Kopidakis, Nikos

    2015-11-16

    We report on photoconductivity of films of CdTe nanocrystals (NCs) using time-resolved microwave photoconductivity (TRMC). Spherical and tetrapodal CdTe NCs with tunable size-dependent properties are studied as a function of surface ligand (including inorganic molecular chalcogenide species) and annealing temperature. Relatively high carrier mobility is measured for films of sintered tetrapod NCs (4 cm2/(V s)). Our TRMC findings show that Te2- capped CdTe NCs show a marked improvement in carrier mobility (11 cm2/(V s)), indicating that NC surface termination can be altered to play a crucial role in charge-carrier mobility even after the NC solids are sintered into bulk films.

  19. A=19B (1995TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    95TI07) (Not illustrated) 19B has been observed in the bombardment of Be by 12 MeV/A 56Fe ions (1984MU27) and in the fragmentation of 44 MeV/A 40Ar (1988GU1A) and 55 MeV/A 48Ca (1991MU19). See also (1989DE52). The mass excess adopted by (1993AU05) is 59.360 ± 0.400 MeV. Shell model predictions for low-lying levels are discussed in (1992WA22). See also (1989PO1K, 1990LO11

  20. A=20N (1998TI06)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    98TI06) (Not illustrated) 20N is particle stable. Its atomic mass excess is 21.770 ± 0.050 MeV (1995AU04). It has been observed in heavy-ion transfer (1989OR03) and projectile fragmentation reactions (1987GI05, 1988DUZT, 1988MU08, 1990MU06, 1991OR01) and in target fragmentation reactions (1988WO09, 1991RE02, 1993WOZZ). See also the review (1988VI1D). Mass measurements were reported in (1987GI05, 1988WO09, 1989OR03, 1991OR01, 1993WOZZ). Nuclear matter rms radii have been derived from

  1. A=3Li (1987TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1987TI07) GENERAL: The previous compilation (1975FI08) listed a small number of references reporting on the four reactions discussed below. Only one of the experiments cited contained any evidence for a 3p resonance, and the discussion suggested that the observed enhancement in 3He(p, n) was more likely a final state interaction. In the work reported since (1975FI08) and listed below, only (1974POZN) contains any mention of the tri-proton, and no evidence for its existence was observed. 1. 2H(p,

  2. A=6n (2002TI10)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2002TI10) (Not illustrated) 6n has not been observed. See (1979AJ01, 1988AJ01) and references cited there. More recently (1990AL40) reports a search for 6n in a 14C(7Li, 6n) activation experiment at E(7Li) = 82 MeV. No evidence for 6n was obtained. The method of angular potential functions was used by (1989GO18) in a calculation of the properties of multi-neutron systems which indicated that these systems have no bound states. The ground state energy of a six-neutron drop has been computed with

  3. Fabrication and Physics of CdTe Devices by Sputtering: Final Report, 1 March 2005 - 30 November 2008

    SciTech Connect (OSTI)

    Compaan, A.; Collins, R.; Karpov, V.; Giolando, D.

    2009-04-01

    Work to understand CdS/CdTe solar cell device physics; increase magnetron sputtering rate (while keeping high device quality); reduce thickness of CdTe layers (while keeping voltage and fill factor).

  4. Growth of CdTe thin films on graphene by close-spaced sublimation method

    SciTech Connect (OSTI)

    Jung, Younghun; Yang, Gwangseok; Kim, Jihyun, E-mail: hyunhyun7@korea.ac.kr [Department of Chemical and Biological Engineering, Korea University, Seoul 136-701 (Korea, Republic of)] [Department of Chemical and Biological Engineering, Korea University, Seoul 136-701 (Korea, Republic of); Chun, Seungju; Kim, Donghwan [Department of Materials Science and Engineering, Korea University, Seoul 136-701 (Korea, Republic of)] [Department of Materials Science and Engineering, Korea University, Seoul 136-701 (Korea, Republic of)

    2013-12-02

    CdTe thin films grown on bi-layer graphene were demonstrated by using the close-spaced sublimation method, where CdTe was selectively grown on the graphene. The density of the CdTe domains was increased with increasing the number of the defective sites in the graphene, which was controlled by the duration of UV exposure. The CdTe growth rate on the bi-layer graphene electrodes was 400?nm/min with a bandgap energy of 1.451.49?eV. Scanning electron microscopy, micro-Raman spectroscopy, micro-photoluminescence, and X-ray diffraction technique were used to confirm the high quality of the CdTe thin films grown on the graphene electrodes.

  5. Ba{sub 2}TeO: A new layered oxytelluride

    SciTech Connect (OSTI)

    Besara, T.; Ramirez, D.; Sun, J.; Whalen, J.B.; Tokumoto, T.D.; McGill, S.A.; Singh, D.J.; Siegrist, T.

    2015-02-15

    Single crystals of the new semiconducting oxytelluride phase, Ba{sub 2}TeO, were synthesized from barium oxide powder and elemental tellurium in a molten barium metal flux. Ba{sub 2}TeO crystallizes in tetragonal symmetry with space group P4/nmm (#129), a=5.0337(1) Å, c=9.9437(4) Å, Z=2. The crystals were characterized by single crystal x-ray diffraction, heat capacity and optical measurements. The optical measurements along with electronic band structure calculations indicate semiconductor behavior with a band gap of 2.93 eV. Resistivity measurements show that Ba{sub 2}TeO is highly insulating. - Graphical abstract: Starting from a simple stacking of rocksalt layers, the final structure of Ba{sub 2}TeO can be obtained by accommodation of structural strain via atom displacements. Density of states calculations and optical absorbance measurements show that Ba{sub 2}TeO has a band gap of 2.93 eV, indicative of semiconductor behavior. - Highlights: • Single crystal synthesis of a new layered oxytelluride, Ba{sub 2}TeO. • The structure features inverse PbO-type BaO layers and NaCl-type BaTe layers. • Optical absorbance show Ba{sub 2}TeO to be a semiconductor with a 2.93 eV gap. • Density of states indicate a small hybridization between Te 5p and Ba 5d states. • The BaTe (BaO) layers dominate the heat capacity at low (high) temperatures.

  6. Fabrication of TiO{sub 2} Thick Film for Photocatalyst from Commercial TiO{sub 2} Powder

    SciTech Connect (OSTI)

    Asteti, S. Fuji; Syarif, D. Gustaman

    2008-03-17

    Photocatalytic activity of TiO{sub 2} thick film ceramics made of commercial TiO{sub 2} powder has been studied. The TiO{sub 2} powder was nano sized one that was derived from dried TiO{sub 2} suspension. The TiO{sub 2} suspension was made by pouring some blended commercial TiO{sub 2} powder into some amount of water. The paste of TiO{sub 2} was made by mixing the nano sized TiO{sub 2} powder with organic vehicle and glass frit. The paste was spread on a glass substrate. The paste was dried at 100 deg. C and heated at different temperatures (400 deg. C and 500 deg. C) for 60 minutes to produce thick film ceramics. The photocatalytic activity of these films was evaluated by measuring the concentration of a solution of methylene blue where the thick films were inside after being illuminated by UV light at various periods of times. The initial concentration of the methylene blue solution was 5 ppm. Structural analyses were carried out by X-ray diffraction (XRD). The XRD analyses showed that the produced thick film ceramic had mainly crystal structure of anatase. According to the photocatalytical data, it was known that the produced thick film ceramics were photocatalyst which were capable of decomposing an organic compound such as the methylene blue.

  7. Electrostatic carrier doping of GdTiO{sub 3}/SrTiO{sub 3} interfaces

    SciTech Connect (OSTI)

    Moetakef, Pouya; Cain, Tyler A.; Zhang, Jack Y.; Janotti, Anderson; Van de Walle, Chris G.; Stemmer, Susanne; Ouellette, Daniel G.; Allen, S. James; Klenov, Dmitri O.; Rajan, Siddharth

    2011-12-05

    Heterostructures and superlattices consisting of a prototype Mott insulator, GdTiO{sub 3}, and the band insulator SrTiO{sub 3} are grown by molecular beam epitaxy and show intrinsic electronic reconstruction, approximately 1/2 electron per surface unit cell at each GdTiO{sub 3}/SrTiO{sub 3} interface. The sheet carrier densities in all structures containing more than one unit cell of SrTiO{sub 3} are independent of layer thicknesses and growth sequences, indicating that the mobile carriers are in a high concentration, two-dimensional electron gas bound to the interface. These carrier densities closely meet the electrostatic requirements for compensating the fixed charge at these polar interfaces. Based on the experimental results, insights into interfacial band alignments, charge distribution, and the influence of different electrostatic boundary conditions are obtained.

  8. Photo-catalytic oxidation of acetone on a TiO2 powder: An in situ FTIR investigation

    SciTech Connect (OSTI)

    Szanyi, Janos; Kwak, Ja Hun

    2015-09-01

    In situ transmission infrared spectroscopy was used to investigate the photo-oxidation of acetone on a commercial, oxidized TiO2 (P25) powder catalyst under UV irradiation at ambient temperature, in the absence and presence of gas phase O2. The photochemistry of a number of organic molecules (1-butanone, methanol and acetic acid,) under the same conditions was also studied in order to identify reaction intermediates and products formed in the photo-oxidation of acetone. Under anaerobic conditions (in the absence of gas phase oxygen) limited extent of photo-oxidation of acetone took place on the oxidized TiO2 sample. In the presence of O2 in the gas phase, however, acetone was completely converted to acetates and formates, and ultimately CO2. The initial step in the sequence of photo-induced reactions is the ejection of a methyl radical, resulting in the formation of surface acetates (from the acetyl group) and formates (from the methyl radicals). Acetate ions are also converted to formates, that, in turn, photo-oxidized to CO2. Under the experimental conditions applied the accumulation of carbonates and bicarbonates were observed on the TiO2 surface as the photo-oxidation of acetone proceeded (this was also observed during the course of photo-oxidation of all the other organics studied here). When the initial radical ejection step produced hydrocarbons containing more than one C atoms (as in the case in 2-butanone and mesytil oxide), the formation of aldehydes on the catalyst surface was also observed as a result of secondary reactions. This work was supported by the US Department of Energy, Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences & Biosciences. Pacific Northwest National Laboratory is operated by Battelle for the US Department of Energy. JHK also acknowledges the support of this work by the 2014 Research Fund of UNIST (Ulsan National Institute of Science and Technology, Ulsan, Korea). The authors thank M.A. Henderson for the fruitful discussions on the photo-oxidation of organic molecules on TiO2.

  9. Phase equilibria, formation, crystal and electronic structure of ternary compounds in Ti-Ni-Sn and Ti-Ni-Sb ternary systems

    SciTech Connect (OSTI)

    Romaka, V.V.; Rogl, P.; Romaka, L.; Stadnyk, Yu.; Melnychenko, N.; Grytsiv, A.; Falmbigl, M.; Skryabina, N.

    2013-01-15

    The phase equilibria of the Ti-Ni-Sn and Ti-Ni-Sb ternary systems have been studied in the whole concentration range by means of X-ray and EPM analyses at 1073 K and 873 K, respectively. Four ternary intermetallic compounds TiNiSn (MgAgAs-type), TiNi{sub 2-x}Sn (MnCu{sub 2}Al-type), Ti{sub 2}Ni{sub 2}Sn (U{sub 2}Pt{sub 2}Sn-type), and Ti{sub 5}NiSn{sub 3} (Hf{sub 5}CuSn{sub 3}-type) are formed in Ti-Ni-Sn system at 1073 K. The TiNi{sub 2}Sn stannide is characterized by homogeneity in the range of 50-47 at% of Ni. The Ti-Ni-Sb ternary system at 873 K is characterized by formation of three ternary intermetallic compounds, Ti{sub 0.8}NiSb (MgAgAs-type), Ti{sub 5}Ni{sub 0.45}Sb{sub 2.55} (W{sub 5}Si{sub 3}-type), and Ti{sub 5}NiSb{sub 3} (Hf{sub 5}CuSn{sub 3}-type). The solubility of Ni in Ti{sub 0.8}NiSb decreases number of vacancies in Ti site up to Ti{sub 0.91}Ni{sub 1.1}Sb composition. - Graphical abstract: Isothermal section of the Ti-Ni-Sn phase diagram and DOS distribution in hypothetical TiNi{sub 1+x}Sn solid solution. Highlights: Black-Right-Pointing-Pointer Ti-Ni-Sn phase diagram was constructed at 1073 K. Black-Right-Pointing-Pointer Four ternary compounds are formed: TiNiSn, TiNi{sub 2-x}Sn, Ti{sub 2}Ni{sub 2}Sn, and Ti{sub 5}NiSn{sub 3}. Black-Right-Pointing-Pointer Three ternary compounds exist in Ti-Ni-Sb system at 873 K. Black-Right-Pointing-Pointer The TiNi{sub 2}Sb compound is absent.

  10. Development of Ti/Ti{sub 3}Sn functionally gradient material produced by eutectic bonding method

    SciTech Connect (OSTI)

    Kirihara, S.; Takeda, M.; Tsujimoto, T. [Ibaraki Univ., Hitachi (Japan). Faculty of Engineering] [Ibaraki Univ., Hitachi (Japan). Faculty of Engineering

    1996-07-15

    Although many materials which have a single function have been developed, future needs are anticipated to include materials which have various functions. A functionally gradient material (FGM) which has characteristics of two different materials is a promising candidate for multi-functional material. The present methods for production of FGM, however, are very complicated and costly. In this study the authors answer the serious problem of high production cost by fabricating the FGM by a eutectic bonding method. This fabrication method includes structural control of FGM by changing the cooling process. They describe Ti/Ti{sub 3}Sn FGM obtained by the eutectic bonding method, and tell how the structure of its composition gradient part is changed by controlling the cooling process.

  11. Milestone L3:THM.CFD.P6.01: Hydra-TH Advanced Capabilities J. Bakosi, M.A. Christon, L.A. Pritchett-

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    THM.CFD.P6.01: Hydra-TH Advanced Capabilities J. Bakosi, M.A. Christon, L.A. Pritchett- Sheats, LANL R.R. Nourgaliev, INL February 1, 2013 CASL-8-2013-0288-000 CASL-U-2013-0288-000 Hydra-TH Advanced Capabilities (L3 Milestone THM.CFD.P6.01) LA-UR 13-20572 J. Bakosi, M.A. Christon, L.A. Pritchett-Sheats Computational Physics Group (CCS-2) Computer, Computational and Statistical Sciences Division Los Alamos National Laboratory Los Alamos, NM 87544 R.R. Nourgaliev Reactor Safety Simulation Group

  12. Nondestructive evaluation of Ni-Ti shape memory alloy

    SciTech Connect (OSTI)

    Meir, S.; Gordon, S.; Karsh, M.; Ayers, R.; Olson, D. L.; Wiezman, A.

    2011-06-23

    The nondestructive evaluation of nickel titanium (Ni-Ti) alloys for applications such as heat treatment for biomaterials applications (dental) and welding was investigated. Ni-Ti alloys and its ternary alloys are valued for mechanical properties in addition to the shape memory effect. Two analytical approaches were perused in this work. Assessment of the microstructure of the alloy that determines the martensitic start temperature (Ms) of Ni-Ti alloy as a function of heat treatment, and secondly, an attempt to evaluate a Friction Stir Welding, which involves thermo-mechanical processing of the alloy.

  13. Nutritional status and random blood glucose, cholesterol and triglyceride test among Malaysian Army (MA) personnel in Kuala Lumpur

    SciTech Connect (OSTI)

    Nadiy, I.; Razalee, S.; Zalifah, M. K.; Zulkeffeli, M. J.

    2013-11-27

    With the rising trend of obesity among the general population, it is also important to assess the obesity and health status among military population. The aim of this study was to determine the prevalence of overweight and obesity among Malaysian Army (MA) personnel as well as the relationship between selected socio-demographics factors, antropometric profiles, body composition and random blood test value. A cross sectional study involving 378 male military personnel aged between 20 to 48 years old was conducted at two MA bases in Kuala Lumpur between November and December 2012. Antropometric measurements included height, weight and waist circumference (WC). Body fat percentage was measured using bioelectrical impedance analysis method (Tanita TBF-300A). Mean height, weight, BMI, WC, body fat percentage, age, monthly income and duration of service were 1.71 ± 0.6 m, 71.7 ± 12.2 kg, 24.6 ± 4.1 kg/m{sup 2}, 87.0 ± 10.0 cm, 23.4 ± 6.6%, 29.1 ± 5.5 years, RM 2115.12 ± 860.70 and 9.9 ± 5.6 years respectively. According to WHO (1998) classification of BMI, 3.2% of the subjects were underweight, 54.8% normal, 32.8% overweight and 9.3% obese. It was obeserved that 40.2% of the subjects had waist circumference value of 90 cm or more and were considered high risk for diebetes and cardiovascular diseases. This study found that BMI was highly correlated with weight (r=0.925, p<0.05), WC (r=0.852, p<0.05) and body fat percentage. Body fat percentage also show high correlation with weight (r=0.759, p<0.05) and WC (r=0.768, p<0.05. The result from 173 of 378 subjects that were selected for random blood test found that 4.6%, 3.5% and 26.0% had diabetes, high cholesterol and high triglyceride respectively. There was a weak correlation between random blood glucose level with weight (r=0.221, p<0.05), BMI (r=0.243, p<0.05), WC (r=0.298, p<0.05), body fat percentage (r=0.163, p<0.05) and age (r=0.223, p<0.05). Random blood cholesterol level had significant correlation with weight (r=0.284, p<0.05), BMI (r=0.260, p<0.05), WC (r=0.362, p<0.05) and body fat percentage (r=0.313, p<0.05). It was also noted that random blood triglyceride level was significantly correlated with weight (r=0.223, p<0.05), BMI (r=0.312, p<0.05), WC (r=0.288, p<0.05), body fat percentage (r=0.287, p<0.05) and age (r=0.268 p<0.05). These results call for attention to the existence of overweight and obesity as well as the risk of non-communicable diseases among military population. Therefore, future intervention from the aspect of nutritional education and health awareness can benefit thus optimizing the health status of MA military personnel.

  14. A=16B (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    93TI07) (Not illustrated) This nucleus has not been observed in the 4.8 GeV proton bombardment of a uranium target. It is particle unstable. Its mass excess is predicted to be 37.97 MeV; it would then be unstable with respect to decay into 15B + n by 0.93 MeV. See (1985WA02, 1986AJ04). The ground state is predicted to have Jπ = 0- and the first three excited states are predicted to lie at 0.95, 1.10, and 1.55 MeV [Jπ = 2-, 3-, 4-] in a (0 + 1)ℏω space shell model calculation. See (1983ANZQ,

  15. A=16C (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    93TI07) (See Energy Level Diagrams for 16C) GENERAL: See Table Prev. Table 16.1 preview 16.1 [General Table] (in PDF or PS) and Table Prev. Table 16.2 preview 16.2 [Table of Energy Levels] (in PDF or PS) here. 1. 16C(β-)16N Qm = 8.012 The half life of 16C is 0.747 ± 0.008 sec. It decays to 16N*(0.12, 3.35, 4.32) [Jπ = 0-, 1+, 1+]: see Table Prev. Table 16.3 preview 16.3 (in PDF or PS) and (1993CH06). See also (1986AJ04) and see (1986KI05, 1988WA1E, 1992WA1L) for theoretical discussions of

  16. A=16F (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    93TI07) (See Energy Level Diagrams for 16F) GENERAL: See Table Prev. Table 16.29 preview 16.29 [General Table] (in PDF or PS) here. See also Table Prev. Table 16.30 preview 16.30 [Table of Energy Levels] (in PDF or PS) here. 1. (a) 14N(3He, n)16F Qm = -0.957 (b) 14N(3He, np)15O Qm = -0.421 Obserevd neutron groups from reaction (a) and results from reaction (b) are displayed in Table Prev. Table 16.31 preview 16.31 (in PDF or PS). A recent measurement of n-p angular correlations from 14N(3He,

  17. A=16Ne (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    93TI07) (See the Isobar Diagram for 16Ne) GENERAL: See Table Prev. Table 16.29 preview 16.29 [General Table] (in PDF or PS) and Table Prev. Table 16.32 preview 16.32 [Table of Energy Levels] (in PDF or PS). Mass of 16Ne: The Q-values of the 20Ne(α, 8He) and 16O(π+, π-) reactions lead to atomic mass excesses of 23.93 ± 0.08 MeV (1978KE06), 23.978 ± 0.024 MeV (1983WO01) and 24.048 ± 0.045 MeV (1980BU15) [recalculated using the (1985WA02) masses for 8He, 16O and 20Ne]. The weighted mean is

  18. A=16O (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    93TI07) (See Energy Level Diagrams for 16O) GENERAL: See Table Prev. Table 16.12 preview 16.12 [General Table] (in PDF or PS) and Table Prev. Table 16.13 preview 16.13 [Table of Energy Levels] (in PDF or PS). < r2 > 1/2 = 2.710 ± 0.015 fm (1978KI01) Abundance = (99.762 ± 0.015)% (1984DE53) |g| = 0.556 ± 0.004 (1984AS03) 1. 9Be(9Be, 2n)16O Qm = 11.289 Total reaction cross sections and characteristic γ-ray cross sections for 9Be + 9Be were measured for Ec.m. = 1.4 - 3.4 MeV (1988LA25).

  19. A=17C (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    93TI07) (See the Isobar Diagram for 17C) The atomic mass excess given by (1988WA18) for 17C is 21035 ± 17 keV. See also (1986AN07). 17C is then stable with respect to 16C + n by 0.73 MeV. Eβ- (max) to 17Ng.s. = 13.16 MeV. See also (1986BI1A). The half-life of 17C has been measured to be 202 ± 17 msec (1986CU01), 220 ± 80 msec (1986DU07), 180 ± 31 msec (1988SA04), and 174 ± 31 msec (1991RE02). Relative intensities of β-delayed gammas were measured by (1986DU07, 1986HU1A, 1986JEZY) [see

  20. A=17Ne (1993TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    93TI07) (See the Isobar Diagram for 17Ne) GENERAL: See Table Prev. Table 17.26 preview 17.26 [Table of Energy Levels] (in PDF or PS). 1. (a) 17Ne(β+)17F* → 16O + p Qm = 13.928 (b) 17Ne(β+)17F → 13N + α Qm = 8.711 (c) 17Ne(β+)17F Qm = 14.529 The half-life of 17Ne has been reported as 109.0 ± 1.0 msec (1971HA05) and 109.3 ± 0.6 msec (1988BO39): the weighted mean is 109.2 ± 0.6 and we adopt it. The decay is primarily to the proton unstable states of 17F at 4.65, 5.49, 6.04 and 8.08 MeV

  1. A=18B (1995TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    95TI07) (Not illustrated) 18B has not been observed in the bombardment of Ta by 44 MeV/A Ar ions (1985DE60, 1985LA03, 1986PO13) or in the bombardment of Be by 12 MeV/A 56Fe ions (1984MU27). 18B has been predicted to have a mass excess of 52.3 MeV (1993AU05). It would then be unstable with respect to 17B + n by 0.5 MeV: see (1978AJ03, 1985WA02). 18B is calculated to have Jπ = 4- and to have excited states at 0.62, 0.86 and 1.59 MeV with Jπ = 1-, 2- and 2- (1985PO10).The shell model calculations

  2. A=19N (1995TI07)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    95TI07) (See the Isobar Diagram for 19N) 19N has been produced in a number of different multinucleon transfer reactions (1983AJ01, 1987AJ02), and these results lead to an adopted value (1993AU05) of 15.860 ± 0.016 MeV for the mass excess. 19N is then stable with respect to decay into 18N + n by 5.33 MeV. The half-life has been measured to be 0.32 ± 0.10 s (1986DU07), 0.21+0.2-0.1 s (1988MU08), 0.235 ± 0.032 s (1988SA04), 0.300 ± 0.080 s (1988DUZT), 0.329 ± 0.019 s (1991RE02). The neutron

  3. A=7H (2002TI10)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2002TI10) (Not illustrated) 7H has not been observed. Attempts have been made to detect it in the spontaneous fission of 252Cf (1982AL33) and in the 7Li(π-, π+) reaction [see (1984AJ01)]. A study of 9Be(π-, 2p) (1987GO25) found no evidence for 7H. See also the review of (1989OG1B) and the 7Li(π-, π+) investigation reported in (1989GR06). The ground state is calculated to have Jπ = 1/2+ and to be unstable with respect to 1n, 2n, 3n and 4n emission. Excited states are predicted at 4.84, 5.00

  4. The effect of structural vacancies on the thermoelectric properties of (Cu?Te){sub 1x}(Ga?Te?)x

    SciTech Connect (OSTI)

    Ye, Zuxin; Young Cho, Jung; Tessema, Misle M.; Salvador, James R.; Waldo, Richard A.; Wang, Hsin; Cai, Wei

    2013-05-01

    We have studied the effects of structural vacancies on the thermoelectric properties of the ternary compounds (Cu?Te)1x(Ga?Te?)x (x=0.5, 0.55, 0.571, 0.6, 0.625, 0.667 and 0.75), which are solid solutions found in the pseudo-binary phase diagram for Cu?Te and Ga?Te?, and possesses tunable structural vacancy concentrations. This materials system is not suitable due to the cost and scarcity of the constituent elements, but the vacancy behavior is well understood and will provide a valuable test case for other systems more suitable from the standpoint of cost and abundance of raw materials, which also possesses these vacancy features, but whose structural characterization is lacking at this stage. We find that the nominally defect free phase CuGaTe? possess the highest ZT (ZT=ST/??, where S is the Seebeck coefficient and ? is the electrical resistivity ? is the thermal conductivity and T is the absolute temperature) which approaches 1 at 840 K and seems to continuously increase above this temperature. This result is due to the unexpectedly low thermal conductivity found for this material at high temperature. The low thermal conductivity was caused by strong Umklapp (thermally resistive scattering processes involving three phonons) phonon scattering. We find that due to the coincidentally strong scattering of carriers by the structural defects that higher concentrations of these features lead to poor electrical transport properties and decreased ZT. - Graphical abstract: Thermal conductivity and zT as a function of temperature for a series of compounds of the type (Cu?Te)1x(Ga?Te?)x (x=0.5, 0.55, 0.571, 0.6, 0.625, 0.667 and 0.75). Highlights: All the samples show p-type semiconducting behavior in the temperature dependence of the Seebeck and Hall coefficients. The increased carrier concentration and the introduction of vacancies diminish the carrier mobility and power factor. The low temperature k decreases significantly as the Ga?Te? content increases due to increasing point defects. The highest ZT ~ 1.0 at 840 K among the samples in this study was found in CuGaTe?, which contains no vacancies.

  5. Evidence for charge Kondo effect in superconducting Tl-doped PbTe (Journal

    Office of Scientific and Technical Information (OSTI)

    Article) | SciTech Connect Evidence for charge Kondo effect in superconducting Tl-doped PbTe Citation Details In-Document Search Title: Evidence for charge Kondo effect in superconducting Tl-doped PbTe We report results of low-temperature thermodynamic and transport measurements of Pb{sub 1-x}Tl{sub x}Te single crystals for Tl concentrations up to the solubility limit of approximately x = 1.5%. For all doped samples, we observe a low-temperature resistivity upturn that scales in magnitude

  6. NuTeV Anomaly Helps Shed Light on Physics of the Nucleus | Jefferson Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NuTeV Anomaly Helps Shed Light on Physics of the Nucleus NuTeV Anomaly Helps Shed Light on Physics of the Nucleus NEWPORT NEWS, VA, June 29, 2009 - A new calculation clarifies the complicated relationship between protons and neutrons in the atomic nucleus and offers a fascinating resolution of the famous NuTeV Anomaly. The calculation, published in the journal Physical Review Letters on June 26, was carried out by a collaboration of researchers from the Department of Energy's Thomas Jefferson

  7. Chapter 1.19: Cadmium Telluride Photovoltaic Thin Film: CdTe

    SciTech Connect (OSTI)

    Gessert, T. A.

    2012-01-01

    The chapter reviews the history, development, and present processes used to fabricate thin-film, CdTe-based photovoltaic (PV) devices. It is intended for readers who are generally familiar with the operation and material aspects of PV devices but desire a deeper understanding of the process sequences used in CdTe PV technology. The discussion identifies why certain processes may have commercial production advantages and how the various process steps can interact with each other to affect device performance and reliability. The chapter concludes with a discussion of considerations of large-area CdTe PV deployment including issues related to material availability and energy-payback time.

  8. Nucleation of AgInSbTe films employed in phase-change media (Journal

    Office of Scientific and Technical Information (OSTI)

    Article) | SciTech Connect Nucleation of AgInSbTe films employed in phase-change media Citation Details In-Document Search Title: Nucleation of AgInSbTe films employed in phase-change media In phase-change technology small volumes of a chalcogenide material are switched between amorphous and crystalline states by local heating with a short laser or current pulses. AgInSbTe is an alloy frequently used in optical data storage, which could also be applied in electronic data storage. For those

  9. ON THE ENERGY SPECTRA OF GeV/TeV COSMIC RAY LEPTONS (Journal Article) |

    Office of Scientific and Technical Information (OSTI)

    SciTech Connect ON THE ENERGY SPECTRA OF GeV/TeV COSMIC RAY LEPTONS Citation Details In-Document Search Title: ON THE ENERGY SPECTRA OF GeV/TeV COSMIC RAY LEPTONS Recent observations of cosmic ray (CR) electrons from several instruments have revealed various degrees of deviation in the measured electron energy distribution from a simple power law, in the form of an excess around 0.1-1 TeV energies. An even more prominent deviation and excess has been observed in the fraction of CR positrons

  10. On the Energy Spectra of GeV/TeV Cosmic Ray Leptons (Journal Article) |

    Office of Scientific and Technical Information (OSTI)

    SciTech Connect On the Energy Spectra of GeV/TeV Cosmic Ray Leptons Citation Details In-Document Search Title: On the Energy Spectra of GeV/TeV Cosmic Ray Leptons Recent observations of cosmic ray electrons from several instruments have revealed various degrees of deviation in the measured electron energy distribution from a simple power-law, in a form of an excess around 0.1 to 1 TeV energies. An even more prominent deviation and excess has been observed in the fraction of cosmic ray

  11. Ultrafast terahertz-induced response of GeSbTe phase-change materials

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect terahertz-induced response of GeSbTe phase-change materials Citation Details In-Document Search Title: Ultrafast terahertz-induced response of GeSbTe phase-change materials The time-resolved ultrafast electric field-driven response of crystalline and amorphous GeSbTe films has been measured all-optically, pumping with single-cycle terahertz pulses as a means of biasing phase-change materials on a sub-picosecond time-scale. Utilizing the near-band-gap

  12. Modeling and experimental studies of oxide covered metal surfaces: TiO{sub 2}/Ti a model system. Progress report

    SciTech Connect (OSTI)

    Smyrl, W.H.

    1991-12-31

    Prior work in our laboratories at the Corrosion Research Center has shown that thin, anodic TiO{sub 2} films formed by the Slow Growth Mode (SGM) on polycrystalline titanium and microcrystalline with a texture that varies from one metal grain to another. Furthermore, the underlying metal grains are mapped by the photoelectrochemical response of the oxide. The same characteristics have also been demonstrated in our laboratory for ZnO grown on Zn. The TiO{sub 2}/Ti system has been chosen for study both because of its importance in energy systems, and because it can serve as a model system for other metal-metal oxide couples. The investigations of anodic TiO{sub 2} films on Ti have shown that the properties of thin films are consistent with the rutile form of the oxide. Both experimental data and theoretical calculations show the close resemblance to results on single crystal TiO{sub 2}. Furthermore, the modeling studies reveal that the optical transitions near the bandedge arise from the bulk band structure. The photoelectrochemical properties of anodic TiO{sub 2} films have now been shown to obey the simple Gaertner-Butler model for the semiconductor-electrolyte interface, with a few modifications. The most important deviation has now been shown to be a result of multiple internal reflections in the oxide film.

  13. Modeling and experimental studies of oxide covered metal surfaces: TiO sub 2 /Ti a model system

    SciTech Connect (OSTI)

    Smyrl, W.H.

    1991-01-01

    Prior work in our laboratories at the Corrosion Research Center has shown that thin, anodic TiO{sub 2} films formed by the Slow Growth Mode (SGM) on polycrystalline titanium and microcrystalline with a texture that varies from one metal grain to another. Furthermore, the underlying metal grains are mapped by the photoelectrochemical response of the oxide. The same characteristics have also been demonstrated in our laboratory for ZnO grown on Zn. The TiO{sub 2}/Ti system has been chosen for study both because of its importance in energy systems, and because it can serve as a model system for other metal-metal oxide couples. The investigations of anodic TiO{sub 2} films on Ti have shown that the properties of thin films are consistent with the rutile form of the oxide. Both experimental data and theoretical calculations show the close resemblance to results on single crystal TiO{sub 2}. Furthermore, the modeling studies reveal that the optical transitions near the bandedge arise from the bulk band structure. The photoelectrochemical properties of anodic TiO{sub 2} films have now been shown to obey the simple Gaertner-Butler model for the semiconductor-electrolyte interface, with a few modifications. The most important deviation has now been shown to be a result of multiple internal reflections in the oxide film.

  14. The low energy spectrum of TeO2 bolometers: results and perspectives...

    Office of Scientific and Technical Information (OSTI)

    K. M. ; Huang, H. Z. ; Kadel, R. ; Kazkaz, K. ; Keppel, G. ; Kogler, L. ; Kolomensky, Yu. G. ; Lenz, D. ; Li, Y. L. ; Ligi, C. ; Liu, X. ; Ma, Y. G. ; Maiano, C. ; Maino, M. ;...

  15. Searching for neutrinoless double-beta decay of {sup 130}Te with...

    Office of Scientific and Technical Information (OSTI)

    G. ; Li, Y. L. ; Ligi, C. ; Liu, X. ; Ma, Y. G. ; Maiano, C. ; Maino, M. ; Martinez, M. ; Maruyama, R. H. ; Mei, Y. ; Moggi, N. ; Morganti, S. ; Napolitano, T. ; Nisi, S. ; Nones, ...

  16. DOEiMA-0295

    Office of Scientific and Technical Information (OSTI)

    ... which enhance the contractor's ability to effectively manage the work, while ... The URS Status Report can be required to provide a narrative discussion. The DOE project ...

  17. MA HEAT Loan Overview

    Broader source: Energy.gov [DOE]

    Presents information on the success of Massachusetts's HEAT loan offerings and how the financing tool is funded.

  18. DOEiMA-0295

    Office of Scientific and Technical Information (OSTI)

    ... Technical content - brief quantitative description of form, interface, and function (Item ... Though there is some similarity the focus of each is dif- a. PSWBS The following checklist ...

  19. Photoinduced electron transfer in perylene-TiO2 nanoassemblies

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ABSTRACT: The photosensitization effect of three perylene dye derivatives on titanium dioxide nanoparticles (TiO2 NPs) has been investigated. The dyes used, 1,7-dibromoperylene-3,4...

  20. TI--CR--AL--O thin film resistors

    DOE Patents [OSTI]

    Jankowski, Alan F.; Schmid, Anthony P.

    2000-01-01

    Thin films of Ti--Cr--Al--O are used as a resistor material. The films are rf sputter deposited from ceramic targets using a reactive working gas mixture of Ar and O.sub.2. Resistivity values from 10.sup.4 to 10.sup.10 Ohm-cm have been measured for Ti--Cr--Al--O film <1 .mu.m thick. The film resistivity can be discretely selected through control of the target composition and the deposition parameters. The application of Ti--Cr--Al--O as a thin film resistor has been found to be thermodynamically stable, unlike other metal-oxide films. The Ti--Cr--Al--O film can be used as a vertical or lateral resistor, for example, as a layer beneath a field emission cathode in a flat panel display; or used to control surface emissivity, for example, as a coating on an insulating material such as vertical wall supports in flat panel displays.

  1. Intrinsic Rashba-like splitting in asymmetric Bi{sub 2}Te{sub 3}/Sb{sub 2}Te{sub 3} heterogeneous topological insulator films

    SciTech Connect (OSTI)

    Liu, Xiaofei; Guo, Wanlin

    2014-08-25

    We show by density functional theory calculations that asymmetric hetero-stacking of Bi{sub 2}Te{sub 3}/Sb{sub 2}Te{sub 3} films can modulate the topological surface states. Due to the structure inversion asymmetry, an intrinsic Rashba-like splitting of the conical surface bands is aroused. While such splitting in homogeneous Bi{sub 2}Te{sub 3}-class topological insulators can be realized in films with more than three quintuple layers under external electric fields, the hetero-stacking breaks the limit of thickness for preserving the topological nature into the thinnest two quintuple layers. These results indicate that the hetero-stacking can serve as an efficient strategy for spin-resolved band engineering of topological insulators.

  2. Martensite transformation of epitaxial Ni-Ti films

    SciTech Connect (OSTI)

    Buschbeck, J.; Kozhanov, A.; Kawasaki, J. K.; James, R. D.; Palmstroem, C. J.

    2011-05-09

    The structure and phase transformations of thin Ni-Ti shape memory alloy films grown by molecular beam epitaxy are investigated for compositions from 43 to 56 at. % Ti. Despite the substrate constraint, temperature dependent x-ray diffraction and resistivity measurements reveal reversible, martensitic phase transformations. The results suggest that these occur by an in-plane shear which does not disturb the lattice coherence at interfaces.

  3. Ultrafast Terahertz-Induced Response of GeSbTe Phase-Change Materials...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: Ultrafast Terahertz-Induced Response of GeSbTe Phase-Change Materials Citation Details In-Document ... Publication Date: 2014-07-08 OSTI Identifier: 1136695 Report ...

  4. Thermoelectric properties of AgSbTe? from first-principles calculations

    SciTech Connect (OSTI)

    Rezaei, Nafiseh; Akbarzadeh, Hadi; Hashemifar, S. Javad

    2014-09-14

    The structural, electronic, and transport properties of AgSbTe? are studied by using full-relativistic first-principles electronic structure calculation and semiclassical description of transport parameters. The results indicate that, within various exchange-correlation functionals, the cubic Fd3?m and trigonal R3?m structures of AgSbTe? are more stable than two other considered structures. The computed Seebeck coefficients at different values of the band gap and carrier concentration are accurately compared with the available experimental data to speculate a band gap of about 0.10.35 eV for AgSbTe? compound, in agreement with our calculated electronic structure within the hybrid HSE (Heyd-Scuseria-Ernzerhof) functional. By calculating the semiclassical Seebeck coefficient, electrical conductivity, and electronic part of thermal conductivity, we present the theoretical upper limit of the thermoelectric figure of merit of AgSbTe? as a function of temperature and carrier concentration.

  5. The tin impurity in Bi0.5Sb1.5Te3 alloys

    Broader source: Energy.gov [DOE]

    Extends work on tin to p-type thermoelectric alloys of formula Bi(2-x)Sb(x)Te(3) doped with Sn. Both single crystals and polycrystals prepared using powder metallurgical techniques are studied and properties reported.

  6. Ultrathin nanosheets of CrSiTe3. A semiconducting two-dimensional...

    Office of Scientific and Technical Information (OSTI)

    In this work we for the first time exfoliate the CrSiTe3, a bulk ferromagnetic semiconductor, to mono- and few-layer 2D crystals onto a SiSiO2 substrate. The Raman spectra show ...

  7. Thermoelectric Enhancement in PbTe with K or Na codoping from...

    Office of Scientific and Technical Information (OSTI)

    Thermoelectric Enhancement in PbTe with K or Na codoping from tuning the interaction of the light- and heavy-hole valence bands Citation Details In-Document Search Title: ...

  8. V-183: Cisco TelePresence TC and TE Bugs Let Remote Users Deny...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Remote Users Deny Service and Remote Adjacent Authenticated Users Gain Root Shell Access V-183: Cisco TelePresence TC and TE Bugs Let Remote Users Deny Service and Remote Adjacent...

  9. Shape-controlled narrow-gap SnTe nanostructures: From nanocubes to nanorods and nanowires

    SciTech Connect (OSTI)

    Guo, Shaojun; Andrew F. Fidler; He, Kai; Su, Dong; Chen, Gen; Lin, Qianglu; Pietryga, Jeffrey M.; Klimov, Victor I.

    2015-11-06

    In this study, the rational design and synthesis of narrow-gap colloidal semiconductor nanocrystals (NCs) is an important step toward the next generation of solution-processable photovoltaics, photodetectors, and thermoelectric devices. SnTe NCs are particularly attractive as a Pb-free alternative to NCs of narrow-gap lead chalcogenides. Previous synthetic efforts on SnTe NCs have focused on spherical nanoparticles. Here we report new strategies for synthesis of SnTe NCs with shapes tunable from highly monodisperse nanocubes, to nanorods (NRs) with variable aspect ratios, and finally to long, straight nanowires (NWs). Reaction at high temperature quickly forms thermodynamically favored nanocubes, but low temperatures lead to elongated particles. Transmission electron microscopy studies of reaction products at various stages of the synthesis reveal that the growth and shape-focusing of monodisperse SnTe nanocubes likely involves interparticle ripening, while directional growth of NRs and NWs may be initiated by particle dimerization via oriented attachment.

  10. Giant and tunable valley degeneracy splitting in MoTe 2 (Journal...

    Office of Scientific and Technical Information (OSTI)

    This content will become publicly available on September 7, 2016 Title: Giant and tunable valley degeneracy splitting in MoTe 2 Authors: Qi, Jingshan ; Li, Xiao ; Niu, Qian ; Feng, ...

  11. Ultrafast terahertz-induced response of GeSbTe phase-change materials...

    Office of Scientific and Technical Information (OSTI)

    Title: Ultrafast terahertz-induced response of GeSbTe phase-change materials The time-reso... pulses as a means of biasing phase-change materials on a sub-picosecond time-scale. ...

  12. Structural analysis of Cr aggregation in ferromagnetic semiconductor (Zn,Cr)Te

    SciTech Connect (OSTI)

    Kobayashi, H.; Yamawaki, K.; Nishio, Y.; Kanazawa, K.; Kuroda, S.; Mitome, M.; Bando, Y.

    2013-12-04

    The Cr aggregation in a ferromagnetic semiconductor (Zn,Cr)Te was studied by performing precise analyses using TEM and XRD of microscopic structure of the Cr-aggregated regions formed in iodine-doped Zn{sub 1?x}Cr{sub x}Te films with a relatively high Cr composition x ? 0.2. It was found that the Cr-aggregated regions are composed of Cr{sub 1??}Te nanocrystals of the hexagonal structure and these hexagonal precipitates are stacked preferentially on the (111)A plane of the zinc-blende (ZB) structure of the host ZnTe crystal with its c-axis nearly parallel to the (111){sub ZB} plane.

  13. THE EI'IVIRONMENTAL QUALITY COMPANY CORPCl~V\\TE OFFICE

    Office of Environmental Management (EM)

    EI'IVIRONMENTAL QUALITY COMPANY CORPClVTE OFFICE Ill 36255 MICIat:l;1 '1 J.VENIJE WAYNE , IVICHICA148 '184 te800-5925489 tit fax 800-592-5329 February 20, 2013...

  14. Atomic-force microscopy and photoluminescence of nanostructured CdTe

    SciTech Connect (OSTI)

    Babentsov, V.; Sizov, F.; Franc, J.; Luchenko, A.; Svezhentsova, E. Tsybrii, Z.

    2013-09-15

    Low-dimensional CdTe nanorods with a diameter of 10-30 nm and a high aspect ratio that reaches 100 are studied. The nanorods are grown by the physical vapor transport method with the use of Bi precipitates on the substrates. In addition, thin films of closely packed CdTe nanorods with the transverse dimensions {approx}(100-200) nm are grown. Atomic-force microscopy shows that the cross sections of all of the nanorods were hexagonally shaped. By photoluminescence measurements, the inference about the wurtzite structure of CdTe is supported, and the structural quality, electron-phonon coupling, and defects are analyzed. On the basis of recent ab initio calculations, the nature of defects responsible for the formation of deep levels in the CdTe layers and bulk crystals are analyzed.

  15. NREL Collaboration Boosts Potential for CdTe Solar Cells - News Releases |

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NREL NREL Collaboration Boosts Potential for CdTe Solar Cells February 29, 2016 A critical milestone has been reached in cadmium telluride (CdTe) solar cell technology, helping pave the way for solar energy to directly compete with electricity generated by conventional energy sources. Scientists at the Energy Department's National Renewable Energy Laboratory (NREL) collaborated with researchers at Washington State University and the University of Tennessee to improve the maximum voltage

  16. Electronic correlation and magnetism in the ferromagnetic metal Fe 3 GeTe 2

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect Electronic correlation and magnetism in the ferromagnetic metal Fe 3 GeTe 2 Citation Details In-Document Search This content will become publicly available on April 5, 2017 Title: Electronic correlation and magnetism in the ferromagnetic metal Fe 3 GeTe 2 Authors: Zhu, Jian-Xin ; Janoschek, Marc ; Chaves, D. S. ; Cezar, J. C. ; Durakiewicz, Tomasz ; Ronning, Filip ; Sassa, Yasmine ; Mansson, Martin ; Scott, B. L. ; Wakeham, N. ; Bauer, Eric D. ; Thompson,

  17. Spin glass in semiconducting KFe1.05Ag0.88Te2 single crystals

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Ryu, H.; Lei, H.; Klobes, B.; Warren, J. B.; Hermann, R. P.; Petrovic, C.

    2015-05-26

    We report discovery of KFe1.05Ag0.88Te2 single crystals with semiconducting spin glass ground state. Composition and structure analysis suggest nearly stoichiometric I4/mmm space group but allow for the existence of vacancies, absent in long range semiconducting antiferromagnet KFe1.05Ag0.88Te2. The subtle change in stoichometry in Fe/Ag sublattice changes magnetic ground state but not conductivity, giving further insight into the semiconducting gap mechanism.

  18. Deformation and shape transitions in hot rotating neutron deficient Te isotopes

    SciTech Connect (OSTI)

    Aggarwal, Mamta; Mazumdar, I.

    2009-08-15

    Evolution of the nuclear shapes and deformations under the influence of temperature and rotation is investigated in Te isotopes with neutron number ranging from the proton drip line to the stability valley. Spin dependent critical temperatures for the shape transitions in Te nuclei are computed. Shape transitions from prolate at low temperature and spin to oblate via triaxiality are seen with increasing neutron number and spin.

  19. Diluted magnetic semiconductors based on Sb2-xVxTe3 | Energy Frontier

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Research Centers Diluted magnetic semiconductors based on Sb2-xVxTe3 Home Author: J. S. Dyck, P. Hajek, P. Lostak, C. Uher Year: 2002 Abstract: We report on a diluted magnetic semiconductor based on the Sb2Te3 tetradymite structure doped with very low concentrations of vanadium (1-3 at. %). The anomalous transport behavior and robust magnetic hysteresis loops observed in magnetotransport and magnetic measurements are experimental manifestations of the ferromagnetic state in these materials.

  20. Ultrafast Terahertz-Induced Response of GeSbTe Phase-Change Materials

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect Terahertz-Induced Response of GeSbTe Phase-Change Materials Citation Details In-Document Search Title: Ultrafast Terahertz-Induced Response of GeSbTe Phase-Change Materials Authors: Shu, Michael J. ; Zalden, Peter ; Chen, Frank ; Weems, Ben ; Chatzakis, Ioannis ; Xiong, Feng ; Jeyasingh, Rakesh ; Hoffmann, Matthias C. ; Pop, Eric ; Wong, H.-S.Philip ; Wuttig, Matthias ; Lindenberg, Aaron M. Publication Date: 2014-07-08 OSTI Identifier: 1136695 Report

  1. Ultrathin nanosheets of CrSiTe3. A semiconducting two-dimensional

    Office of Scientific and Technical Information (OSTI)

    ferromagnetic material (Journal Article) | SciTech Connect Ultrathin nanosheets of CrSiTe3. A semiconducting two-dimensional ferromagnetic material Citation Details In-Document Search This content will become publicly available on November 27, 2016 Title: Ultrathin nanosheets of CrSiTe3. A semiconducting two-dimensional ferromagnetic material Finite range ferromagnetism and antiferromagnetism in two-dimensional (2D) systems within an isotropic Heisenberg model at non-zero temperature were

  2. PbTe/TAGS RTG Mars Environmental Survey (MESUR) mission

    SciTech Connect (OSTI)

    Schock, A. )

    1993-01-10

    The paper describes the results of studies on an RTG option for powering the global network of unmanned landers for NASA's Mars Environmental Survey (MESUR) mission. RTGs are essentially unaffected by diurnal and seasonal variations, Martian sandstorms, and landing site latitudes, and their waste heat can stabilize the temperatures of the landers and their payload. The RTG designs described in this paper are based on PbTe/TAGS thermoelectric elements, in contast to the SiGe-based RTGs the author described in previous publications. The presently described RTGs differ not only in the choice of thermoelectric materials but also in the use of much lower operating temperatures, conductive rather than radiative heat transfer, an inert cover gas instead of vacuum in the RTG's converter, and fibrous instead of multifoil thermal insulation. As in a previous Teledyne design, the Fairchild designs described in this paper employ flight-proven General Purpose Source modules and Close-Pack Arrays of thermoelectric converter modules. Illustrative point designs of RTGs producing 41 and 51 watts(e) at 28 volts are presented. The presented performance parameters were derived by detailed thermal, thermoelectric, and electrical analyses (including radiator geometry optimization) described in the paper. The Fairchild study showed that, with appropriate modifications, the Teledyne design can be scaled up to higher power levels, and it identified solutions to ensure adequate fuel clad ductility at launch temperatures and adequate thermal conductance from the thermoelectric cold ends to the RTG housing.

  3. A comparative study of precipitation effects in Ti only and Ti-V Ultra Low Carbon (ULC) strip steels

    SciTech Connect (OSTI)

    Ooi, S.W.; Fourlaris, G. . E-mail: g.fourlaris@swansea.ac.uk

    2006-04-15

    Two ULC steel grades were investigated, one based on combined vanadium and titanium additions and the other based on titanium only additions. It has been established that TiC formation during interphase precipitation retards grain growth of the {l_brace}111{r_brace} texture grains during continuous annealing and hence positively affects the r value of the Ti only steel. The formation of newly formed TiC precipitates on dislocations during continuous annealing has been found to result in an increase of the yield strength in both steel grades, as the annealing temperature is increased. It is also confirmed that VC particles formed during the coiling process dissolve during the continuous annealing cycles. Suitable continuous annealing cycles can be adopted to produce high formable steels with a bake hardening potential using the beneficial effects of combined Ti-V additions.

  4. Ultrathin nanosheets of CrSiTe3. A semiconducting two-dimensional ferromagnetic material

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Lin, Ming -Wei; Zhung, Houlong L.; Yan, Jiaqiang; Ward, Thomas Zac; Puretzky, Alexander A.; Rouleau, Christopher M.; Gai, Zheng; Liang, Liangbo; Meunier, Vincent; Ganesh, Panchapakesan; et al

    2015-11-27

    Finite range ferromagnetism and antiferromagnetism in two-dimensional (2D) systems within an isotropic Heisenberg model at non-zero temperature were originally proposed to be impossible. However, recent theoretical studies using an Ising model have recently shown that 2D magnetic crystals can exhibit magnetism. Experimental verification of existing 2D magnetic crystals in this system has remained elusive. In this work we for the first time exfoliate the CrSiTe3, a bulk ferromagnetic semiconductor, to mono- and few-layer 2D crystals onto a Si/SiO2 substrate. The Raman spectra show the good stability and high quality of the exfoliated flakes, consistent with the computed phonon spectra ofmore » 2D CrSiTe3, giving a strong evidence for the existence of 2D CrSiTe3 crystals. When the thickness of the CrSiTe3 crystals is reduced to few-layers, we observed a clear change in resistivity at 80~120 K, consistent with the theoretical calculations on the Curie temperature (Tc) of ~80 K for the magnetic ordering of 2D CrSiTe3 crystals. As a result, the ferromagnetic mono- and few-layer 2D CrSiTe3 indicated here should enable numerous applications in nano-spintronics.« less

  5. Ion-beam treatment to prepare surfaces of p-CdTe films

    DOE Patents [OSTI]

    Gessert, Timothy A.

    2001-01-01

    A method of making a low-resistance electrical contact between a p-CdTe layer and outer contact layers by ion beam processing comprising: a) placing a CdS/CdTe device into a chamber and evacuating the chamber; b) orienting the p-CdTe side of the CdS/CdTe layer so that it faces apparatus capable of generating Ar atoms and ions of preferred energy and directionality; c) introducing Ar and igniting the area of apparatus capable of generating Ar atoms and ions of preferred energy and directionality in a manner so that during ion exposure, the source-to-substrate distance is maintained such that it is less than the mean-free path or diffusion length of the Ar atoms and ions at the vacuum pressure; d) allowing exposure of the p-CdTe side of the device to said ion beam for a period less than about 5 minutes; and e) imparting movement to the substrate to control the real uniformity of the ion-beam exposure on the p-CdTe side of the device.

  6. Oxygen Incorporation During Fabrication of Substrate CdTe Photovoltaic Devices: Preprint

    SciTech Connect (OSTI)

    Duenow, J. N.; Dhere, R. G.; Kuciauskas, D.; Li, J. V.; Pankow, J. W.; DeHart, C. M.; Gessert, T. A.

    2012-06-01

    Recently, CdTe photovoltaic (PV) devices fabricated in the nonstandard substrate configuration have attracted increasing interest because of their potential compatibility with flexible substrates such as metal foils and polymer films. This compatibility could lead to the suitability of CdTe for roll-to-roll processing and building-integrated PV. Currently, however, the efficiencies of substrate CdTe devices reported in the literature are significantly lower ({approx}6%-8%) than those of high-performance superstrate devices ({approx}17%) because of significantly lower open-circuit voltage (Voc) and fill factor (FF). In our recent device development efforts, we have found that processing parameters required to fabricate high-efficiency substrate CdTe PV devices differ from those necessary for traditional superstrate CdTe devices. Here, we investigate how oxygen incorporation in the CdTe deposition, CdCl2 heat treatment, CdS deposition, and post-deposition heat treatment affect device characteristics through their effects on the junction. By adjusting whether oxygen is incorporated during these processing steps, we have achieved Voc values greater than 860 mV and efficiencies greater than 10%.

  7. Enhanced thermoelectric performance in Cd doped CuInTe{sub 2} compounds

    SciTech Connect (OSTI)

    Cheng, N.; Liu, R.; Bai, S.; Shi, X. Chen, L.

    2014-04-28

    CuIn{sub 1?x}Cd{sub x}Te{sub 2} materials (x?=?0, 0.02, 0.05, and 0.1) are prepared using melting-annealing method and the highly densified bulk samples are obtained through Spark Plasma Sintering. The X-ray diffraction data confirm that nearly pure chalcopyrite structures are obtained in all the samples. Due to the substitution of Cd at In sites, the carrier concentration is greatly increased, leading to much enhanced electrical conductivity and power factor. The single parabolic band model is used to describe the electrical transport properties of CuInTe{sub 2} and the low temperature Hall mobility is also modeled. By combing theoretical model and experiment data, the optimum carrier concentration in CuInTe{sub 2} is proposed to explain the greatly enhanced power factors in the Cd doped CuInTe{sub 2}. In addition, the thermal conductivity is reduced by extra phonon scattering due to the atomic mass and radius fluctuations between Cd and In atoms. The maximum zTs are observed in CuIn{sub 0.98}Cd{sub 0.02}Te{sub 2} and CuIn{sub 0.9}Cd{sub 0.1}Te{sub 2} samples, which are improved by over 100% at room temperature and around 20% at 600?K.

  8. DEGREE-SCALE GeV 'JETS' FROM ACTIVE AND DEAD TeV BLAZARS

    SciTech Connect (OSTI)

    Neronov, A.; Semikoz, D.; Kachelriess, M.; Ostapchenko, S.; Elyiv, A.

    2010-08-20

    We show that images of TeV blazars in the GeV energy band should contain, along with point-like sources, degree-scale jet-like extensions. These GeV extensions are the result of electromagnetic cascades initiated by TeV {gamma}-rays interacting with extragalactic background light and the deflection of the cascade electrons/positrons in extragalactic magnetic fields (EGMFs). Using Monte Carlo simulations, we study the spectral and timing properties of the degree-scale extensions in simulated GeV band images of TeV blazars. We show that the brightness profile of such degree-scale extensions can be used to infer the light curve of the primary TeV {gamma}-ray source over the past 10{sup 7} yr, i.e., over a time scale comparable to the lifetime of the parent active galactic nucleus. This implies that the degree-scale jet-like GeV emission could be detected not only near known active TeV blazars, but also from 'TeV blazar remnants', whose central engines were switched off up to 10 million years ago. Since the brightness profile of the GeV 'jets' depends on the strength and the structure of the EGMF, their observation provides additional information about the EGMF.

  9. Native SrTiO3 (001) surface layer from resonant Ti L2,3 reflectance spectroscopy

    SciTech Connect (OSTI)

    Valvidares, Manuel; Huijben, Mark; Yu, Pu; Ramesh, Ramamoorthy; Kortright, Jeffrey

    2010-11-03

    We quantitatively model resonant Ti L2,3 reflectivity Rs,p(q, hn) from several SrTiO3 (001) single crystals having different initial surface preparations and stored in ambient conditions before and between measurements. All samples exhibit unexpected 300 K Rs(hn) - Rp(hn) anisotropy corresponding to weak linear dichroism and tetragonal distortion of the TiO6 octahedra indicating a surface layer with properties different from cubic SrTiO3. Oscillations in Rs(q) confirm a ubiquitous surface layer 2-3 nm thick that evolves over a range of time scales. Resonant optical constant spectra derived from Rs,p(hn) assuming a uniform sample are refined using a single surface layer to fit measured Rs(q). Differences in surface layer and bulk optical properties indicate that the surface is significantly depleted in Sr and enriched in Ti and O. While consistent with the tendency of SrTiO3 surfaces toward non-stoichiometry, this layer does not conform simply to existing models for the near surface region and apparently forms via room temperature surface reactions with the ambient. This new quantitative spectral modeling approach is generally applicable and has potential to study near-surface properties of a variety of systems with unique chemical and electronic sensitivities.

  10. Structural characterization of Bi{sub 2}Te{sub 3} and Sb{sub 2}Te{sub 3} as a function of temperature using neutron powder diffraction and extended X-ray absorption fine structure techniques

    SciTech Connect (OSTI)

    Mansour, A. N.; Wong-Ng, W.; Huang, Q.; Tang, W.; Thompson, A.; Sharp, J.

    2014-08-28

    The structure of Bi{sub 2}Te{sub 3} (Seebeck coefficient Standard Reference Material (SRM™ 3451)) and the related phase Sb{sub 2}Te{sub 3} have been characterized as a function of temperature using the neutron powder diffraction (NPD) and the extended X-ray absorption fine structure (EXAFS) techniques. The neutron structural studies were carried out from 20 K to 300 K for Bi{sub 2}Te{sub 3} and from 10 K to 298 K for Sb{sub 2}Te{sub 3}. The EXAFS technique for studying the local structure of the two compounds was conducted from 19 K to 298 K. Bi{sub 2}Te{sub 3} and Sb{sub 2}Te{sub 3} are isostructural, with a space group of R3{sup ¯}m. The structure consists of repeated quintuple layers of atoms, Te2-M-Te1-M-Te2 (where M = Bi or Sb) stacking along the c-axis of the unit cell. EXAFS was used to examine the bond distances and static and thermal disorders for the first three shells of Bi{sub 2}Te{sub 3} and Sb{sub 2}Te{sub 3} as a function of temperature. The temperature dependencies of thermal disorders were analyzed using the Debye and Einstein models for lattice vibrations. The Debye and Einstein temperatures for the first two shells of Bi{sub 2}Te{sub 3} are similar to those of Sb{sub 2}Te{sub 3} within the uncertainty in the data. However, the Debye and Einstein temperatures for the third shell of Bi-Bi are significantly lower than those of the third shell of Sb-Sb. The Einstein temperature for the third shell is consistent with a soft phonon mode in both Bi{sub 2}Te{sub 3} and Sb{sub 2}Te{sub 3}. The lower Einstein temperature of Bi-Bi relative to Sb-Sb is consistent with the lower value of thermal conductivity of Bi{sub 2}Te{sub 3} relative to Sb{sub 2}Te{sub 3}.

  11. O3-type layered transition metal oxide Na(NiCoFeTi)1/4O2 as a high rate and long cycle life cathode material for sodium ion batteries

    SciTech Connect (OSTI)

    Yue, Ji -Li; Yang, Xiao -Qing; Zhou, Yong -Ning; Yu, Xiqian; Bak, Seong -Min; Fu, Zheng -Wen

    2015-10-09

    High rate capability and long cycle life are challenging goals for the development of room temperature sodium-ion batteries. Here we report a new single phase quaternary O3-type layer-structured transition metal oxide Na(NiCoFeTi)1/4O2 synthesized by a simple solid-state reaction as a new cathode material for sodium-ion batteries. It can deliver a reversible capacity of 90.6 mA h g–1 at a rate as high as 20C. At 5C, 75.0% of the initial specific capacity can be retained after 400 cycles with a capacity-decay rate of 0.07% per cycle, demonstrating a superior long-term cyclability at high current density. X-ray diffraction and absorption characterization revealed reversible phase transformations and electronic structural changes during the Na+ deintercalation/intercalation process. Ni, Co and Fe ions contribute to charge compensation during charge and discharge. Although Ti ions do not contribute to the charge transfer, they play a very important role in stabilizing the structure during charge and discharge by suppressing the Fe migration. Additionally, Ti substitution can also smooth the charge–discharge plateaus effectively, which provides a potential advantage for the commercialization of this material for room temperature sodium-ion batteries.

  12. O3-type layered transition metal oxide Na(NiCoFeTi)1/4O2 as a high rate and long cycle life cathode material for sodium ion batteries

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Yue, Ji -Li; Yang, Xiao -Qing; Zhou, Yong -Ning; Yu, Xiqian; Bak, Seong -Min; Fu, Zheng -Wen

    2015-10-09

    High rate capability and long cycle life are challenging goals for the development of room temperature sodium-ion batteries. Here we report a new single phase quaternary O3-type layer-structured transition metal oxide Na(NiCoFeTi)1/4O2 synthesized by a simple solid-state reaction as a new cathode material for sodium-ion batteries. It can deliver a reversible capacity of 90.6 mA h g–1 at a rate as high as 20C. At 5C, 75.0% of the initial specific capacity can be retained after 400 cycles with a capacity-decay rate of 0.07% per cycle, demonstrating a superior long-term cyclability at high current density. X-ray diffraction and absorption characterizationmore » revealed reversible phase transformations and electronic structural changes during the Na+ deintercalation/intercalation process. Ni, Co and Fe ions contribute to charge compensation during charge and discharge. Although Ti ions do not contribute to the charge transfer, they play a very important role in stabilizing the structure during charge and discharge by suppressing the Fe migration. Additionally, Ti substitution can also smooth the charge–discharge plateaus effectively, which provides a potential advantage for the commercialization of this material for room temperature sodium-ion batteries.« less

  13. Magneto-transport in LaTi{sub 1−x}Mn{sub x}O{sub 3}/SrTiO{sub 3} oxide heterostructures

    SciTech Connect (OSTI)

    Kumar, Pramod Dogra, Anjana Budhani, R. C.

    2014-04-24

    We report the growth of ultrathin film of Mn doped LaTiO{sub 3} on TiO{sub 2} terminated SrTiO{sub 3} (001) substrate by pulsed laser deposition (PLD) and their electrical transport characteristics including magnetoresistance (MR). Though the replacement of Mn in LaTiO{sub 3} at the Ti site in dilute limit does not affect the metallic behaviour of films but variation in resistance is observed. Normalised resistance behaviour is explained on the basis of variation in charge carriers and increased interaction between Mn atoms in the system under investigation.

  14. Ferroelectric Self-assembled PbTiO3 Perovskite Nanostructures onto

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    (100)SrTiO3 Substrates from a Novel Microemulsion-aided Sol-Gel Preparation Ferroelectric Self-assembled PbTiO3 Perovskite Nanostructures onto (100)SrTiO3 Substrates from a Novel Microemulsion-aided Sol-Gel Preparation Figure 1. PbTiO3 nanostructures onto (100) SrTiO3 substrates. Topography image obtained by Scanning Force Microscopy (SFM), showing nanosized and uniform PbTiO3 particles with a short range one dimensional periodicity detected by the Fast Fourier Transform of the topography

  15. First-epoch VLBA imaging of 20 new TeV blazars

    SciTech Connect (OSTI)

    Piner, B. Glenn; Edwards, Philip G.

    2014-12-10

    We present Very Long Baseline Array (VLBA) images of 20 TeV blazars not previously well studied on the parsec scale. All 20 of these sources are high-frequency peaked BL Lac objects (HBLs). Observations were made between August and December of 2013 at a frequency of 8.4 GHz. These observations represent the first epoch of a VLBA monitoring campaign on these blazars, and they significantly increase the fraction of TeV HBLs studied with high-resolution imaging. The peak very long baseline interferometry (VLBI) flux densities of these sources range from ?10 to ?100 mJy bm{sup 1}, and parsec-scale jet structure is detected in all sources. About half of the VLBI cores are resolved, with brightness temperature upper limits of a few times 10{sup 10} K, and we find that a brightness temperature of ?2 10{sup 10} K is consistent with the VLBI data for all but one of the sources. Such brightness temperatures do not require any relativistic beaming to reduce the observed value below commonly invoked intrinsic limits; however, the lack of detection of counterjets does place a modest limit on the bulk Lorentz factor of ? ? 2. These data are thus consistent with a picture where weak-jet sources like the TeV HBLs develop significant velocity structures on parsec scales. We also extend consideration to the full sample of TeV HBLs by combining the new VLBI data with VLBI and gamma-ray data from the literature. By comparing measured VLBI and TeV fluxes to samples with intrinsically uncorrelated luminosities generated by Monte Carlo simulations, we find a marginally significant correlation between the VLBI and TeV fluxes for the full TeV HBL sample.

  16. Development of a Total Energy, Environment and Asset Management (TE2AM tm) Curriculum

    SciTech Connect (OSTI)

    2012-12-31

    The University of Wisconsin Department of Engineering Professional Development (EPD) has completed the sponsored project entitled, Development of a Total Energy, Environment and Asset Management (TE2AM™) Curriculum. The project involved the development of a structured professional development program to improve the knowledge, skills, capabilities, and competencies of engineers and operators of commercial buildings. TE2AM™ advances a radically different approach to commercial building design, operation, maintenance, and end-­‐of-­‐life disposition. By employing asset management principles to the lifecycle of a commercial building, owners and occupants will realize improved building performance, reduced energy consumption and positive environmental impacts. Through our commercialization plan, we intend to offer TE2AM™ courses and certificates to the professional community and continuously improve TE2AM™ course materials. The TE2AM™ project supports the DOE Strategic Theme 1 -­‐ Energy Security; and will further advance the DOE Strategic Goal 1.4 Energy Productivity. Through participation in the TE2AM™ curriculum, engineers and operators of commercial buildings will be eligible for a professional certificate; denoting the completion of a prescribed series of learning activities. The project involved a comprehensive, rigorous approach to curriculum development, and accomplished the following goals: 1. Identify, analyze and prioritize key learning needs of engineers, architects and technical professionals as operators of commercial buildings. 2. Design and develop TE2AM™ curricula and instructional strategies to meet learning needs of the target learning community. 3. Establish partnerships with the sponsor and key stakeholders to enhance the development and delivery of learning programs. 4. Successfully commercialize and sustain the training and certificate programs for a substantial time following the term of the award. The project team was successful in achieving the goals and deliverables set forth in the original proposal. Though attempts were made to adhere to the original project timeline, the team requested, and was granted a 6-­‐month project extension, during which time the project was completed.

  17. Incorporation of chromium into TiO{sub 2} nanopowders

    SciTech Connect (OSTI)

    Kollbek, Kamila; Sikora, Marcin; Kapusta, Czesław; Szlachetko, Jakub; Radecka, Marta; Lyson-Sypien, Barbara; Zakrzewska, Katarzyna

    2015-04-15

    Highlights: • Nanopowders of TiO{sub 2}:Cr with different amount of Cr dopant were obtained by flame spray synthesis, FSS. • Increase in the optical absorption and a shift of the absorption edge were observed upon Cr doping. • HERFD-XANES measurements indicated that the average valence state of titanium ions was preserved. • Increasing magnetic susceptibility of a paramagnetic character was observed upon Cr doping. - Abstract: The paper reports on the results of a study of optical, electronic and magnetic properties of TiO{sub 2} nanopowders doped with Cr ions. Diffused reflectance spectra reveal an increase in the optical absorption and a shift of the absorption edge towards lower energies upon Cr doping. Direct information on the Ti electronic state and the symmetry of its nearest environment is obtained from XANES Ti K-edge spectra. Magnetic behaviour is probed by means of the temperature dependence of DC magnetic susceptibility. Increasing magnetic susceptibility of a paramagnetic character is observed upon increasing chromium doping. The Curie constant of TiO{sub 2}:10 at.% Cr sample (0.12 emu K/mol Oe) is lower than that expected for Cr{sup 3+} (0.1875 emu K/mol Oe) possibly due to the appearance of Cr{sup 4+} or the presence of the orbital contribution to the magnetic moment.

  18. Electronic inhomogeneity and Ag:Sb imbalance of Ag1-yPb18Sb1+zTe20

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    high-performance thermoelectrics elucidated by 125Te and 207Pb NMR | Energy Frontier Research Centers Electronic inhomogeneity and Ag:Sb imbalance of Ag1-yPb18Sb1+zTe20 high-performance thermoelectrics elucidated by 125Te and 207Pb NMR Home Author: E.M. Levin, B.A. Cook, K. Ahn, M.G. Kanatzidis, K. Schmidt-Rohr Year: 2009 Abstract: Using magic-angle spinning 125Te and 207Pb NMR, we have discovered the presence of two phases of approximately tenfold different free-electron concentration, n,

  19. The Morphology of TiO[subscript 2] (B) Nanoparticles (Journal...

    Office of Scientific and Technical Information (OSTI)

    The Morphology of TiOsubscript 2 (B) Nanoparticles Citation Details In-Document Search Title: The Morphology of TiOsubscript 2 (B) Nanoparticles Authors: Hua, Xiao ; Liu, Zheng ...

  20. FIRST-PRINCIPLES PHASE STABILITY IN THE TI-V ALLOY SYSTEM (Journal...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: FIRST-PRINCIPLES PHASE STABILITY IN THE TI-V ALLOY SYSTEM Citation Details In-Document Search Title: FIRST-PRINCIPLES PHASE STABILITY IN THE TI-V ALLOY SYSTEM ...

  1. Electric control of magnetism at the Fe/BaTiO3 interface (Journal...

    Office of Scientific and Technical Information (OSTI)

    Electric control of magnetism at the FeBaTiO3 interface Citation Details In-Document Search Title: Electric control of magnetism at the FeBaTiO3 interface Interfacial ...

  2. Local Metal and Deuterium Ordering in the Deuterated ZrTiNi C14...

    Office of Scientific and Technical Information (OSTI)

    Local Metal and Deuterium Ordering in the Deuterated ZrTiNi C14 Laves Phase Citation Details In-Document Search Title: Local Metal and Deuterium Ordering in the Deuterated ZrTiNi ...

  3. Electric control of magnetism at the Fe/BaTiO3 interface (Journal...

    Office of Scientific and Technical Information (OSTI)

    Electric control of magnetism at the FeBaTiO3 interface Citation Details In-Document Search Title: Electric control of magnetism at the FeBaTiO3 interface You are accessing a ...

  4. High-Ti-concentration aerogels for bright x-ray sources (Technical...

    Office of Scientific and Technical Information (OSTI)

    Ti-concentration aerogels for bright x-ray sources Citation Details In-Document Search Title: High-Ti-concentration aerogels for bright x-ray sources Authors: Perez, F ; Patterson,...

  5. High-Ti-concentration aerogels for bright x-ray sources (Technical...

    Office of Scientific and Technical Information (OSTI)

    Ti-concentration aerogels for bright x-ray sources Citation Details In-Document Search Title: High-Ti-concentration aerogels for bright x-ray sources You are accessing a...

  6. Deformation behavior of Nb nanowires in TiNiCu shape memory alloy...

    Office of Scientific and Technical Information (OSTI)

    in TiNiCu shape memory alloy matrix This content will become publicly available on August 18, 2016 Title: Deformation behavior of Nb nanowires in TiNiCu shape memory alloy matrix ...

  7. Conversion of 1,3-Propylene Glycol on Rutile TiO2(110) (Journal...

    Office of Scientific and Technical Information (OSTI)

    Conversion of 1,3-Propylene Glycol on Rutile TiO2(110) Citation Details In-Document Search Title: Conversion of 1,3-Propylene Glycol on Rutile TiO2(110) The adsorption of...

  8. The crystal and magnetic structure of Ti-substituted LaCrO{sub...

    Office of Scientific and Technical Information (OSTI)

    On account of a miscibility gap, a higher degree of Ti-substitution at the Cr site cannot be achieved; as a consequence the solid state solubility of Ti in LaCrOsub 3 at 1573 K ...

  9. Reduction of Fermi level pinning and recombination at polycrystalline CdTe surfaces by laser irradiation

    SciTech Connect (OSTI)

    Simonds, Brian J.; Kheraj, Vipul; Palekis, Vasilios; Ferekides, Christos; Scarpulla, Michael A.

    2015-06-14

    Laser processing of polycrystalline CdTe is a promising approach that could potentially increase module manufacturing throughput while reducing capital expenditure costs. For these benefits to be realized, the basic effects of laser irradiation on CdTe must be ascertained. In this study, we utilize surface photovoltage spectroscopy (SPS) to investigate the changes to the electronic properties of the surface of polycrystalline CdTe solar cell stacks induced by continuous-wave laser annealing. The experimental data explained within a model consisting of two space charge regions, one at the CdTe/air interface and one at the CdTe/CdS junction, are used to interpret our SPS results. The frequency dependence and phase spectra of the SPS signal are also discussed. To support the SPS findings, low-temperature spectrally-resolved photoluminescence and time-resolved photoluminescence were also measured. The data show that a modest laser treatment of 250 W/cm{sup 2} with a dwell time of 20 s is sufficient to reduce the effects of Fermi level pinning at the surface due to surface defects.

  10. Static atomic displacements in a CdTe epitaxial layer on a GaAs substrate

    SciTech Connect (OSTI)

    Horning, R.D.; Staudenmann, J.

    1987-05-25

    A (001)CdTe epitaxial layer on a (001)GaAs substrate was studied by x-ray diffraction between 10 and 360 K. The CdTe growth took place at 380 /sup 0/C in a vertical gas flow metalorganic chemical vapor deposition reactor. Lattice parameters and integrated intensities of both the substrate and the epitaxial layer using the (00l) and (hhh) Bragg reflections reveal three important features. Firstly, the GaAs substrate does not exhibit severe strain after deposition and it is as perfect as a bulk GaAs. Secondly, the CdTe unit cell distorts tetragonally with a/sub perpendicular/>a/sub parallel/ below 300 K. The decay of the (00l) reflection intensities as a function of the temperature yields a Debye temperature of 142 K, the same value as for bulk CdTe. Thirdly, a temperature-dependent isotropic static displacement of the Cd and the Te atoms is introduced to account for the anomalous behavior of the (hhh) intensities.

  11. An Experiment to Locate the Site of TeV Flaring in M87

    SciTech Connect (OSTI)

    Harris, D.E.; /Harvard-Smithsonian Ctr. Astrophys.; Massaro, F.; /Harvard-Smithsonian Ctr. Astrophys. /KIPAC, Menlo Park /SLAC; Cheung, C.C.; /Natl. Acad. Sci. /Naval Research Lab, Wash., D.C.; Horns, D.; Raue, M.; /Hamburg U.; Stawarz, L.; /JAXA, Sagamihara /Jagiellonian U., Astron. Observ.; Wagner, S.; /Heidelberg Observ.; Colin, P.; /Munich, Max Planck Inst.; Mazin, D.; /Barcelona, IFAE; Wagner, R.; /Munich, Max Planck Inst.; Beilicke, M.; /McDonnell Ctr. Space Sci.; LeBohec, S.; Hui, M.; /Utah U.; Mukherjee, R.; /Barnard Coll.

    2012-05-18

    We describe a Chandra X-ray target-of-opportunity project designed to isolate the site of TeV flaring in the radio galaxy M87. To date, we have triggered the Chandra observations only once (2010 April) and by the time of the first of our nine observations, the TeV flare had ended. However, we found that the X-ray intensity of the unresolved nucleus was at an elevated level for our first observation. Of the more than 60 Chandra observations we have made of the M87 jet covering nine years, the nucleus was measured at a comparably high level only three times. Two of these occasions can be associated with TeV flaring, and at the time of the third event, there were no TeV monitoring activities. From the rapidity of the intensity drop of the nucleus, we infer that the size of the emitting region is of order a few light days x the unknown beaming factor; comparable to the same sort of estimate for the TeV emitting region. We also find evidence of spectral evolution in the X-ray band which seems consistent with radiative losses affecting the non-thermal population of the emitting electrons within the unresolved nucleus.

  12. Intergalactic magnetic fields and gamma-ray observations of extreme TeV blazars

    SciTech Connect (OSTI)

    Arlen, Timothy C.; Vassilev, Vladimir V.; Weisgarber, Thomas; Wakely, Scott P.; Shafi, S. Yusef

    2014-11-20

    The intergalactic magnetic field (IGMF) in cosmic voids can be indirectly probed through its effect on electromagnetic cascades initiated by a source of teraelectronvolt (TeV) gamma-rays, such as active galactic nuclei (AGNs). AGNs that are sufficiently luminous at TeV energies, 'extreme TeV blazars', can produce detectable levels of secondary radiation from inverse Compton scattering of the electrons in the cascade, provided that the IGMF is not too large. We review recent work in the literature that utilizes this idea to derive constraints on the IGMF for three TeV-detected blazars, 1ES 0229+200, 1ES 1218+304, and RGB J0710+591, and we also investigate four other hard-spectrum TeV blazars in the same framework. Through a recently developed, detailed, three-dimensional particle-tracking Monte Carlo code, incorporating all major effects of QED and cosmological expansion, we research the effects of major uncertainties, such as the spectral properties of the source, uncertainty in the ultraviolet and far-infrared extragalactic background light, undersampled very high energy (energy ≥100 GeV) coverage, past history of gamma-ray emission, source versus observer geometry, and the jet AGN Doppler factor. The implications of these effects on the recently reported lower limits of the IGMF are thoroughly examined to conclude that the presently available data are compatible with a zero-IGMF hypothesis.

  13. Structure-Curie temperature relationships in BaTiO 3 -based ferroelectric

    Office of Scientific and Technical Information (OSTI)

    perovskites: Anomalous behavior of ( Ba , Cd ) TiO 3 from DFT, statistical inference, and experiments (Journal Article) | SciTech Connect Structure-Curie temperature relationships in BaTiO 3 -based ferroelectric perovskites: Anomalous behavior of ( Ba , Cd ) TiO 3 from DFT, statistical inference, and experiments Citation Details In-Document Search This content will become publicly available on April 11, 2017 Title: Structure-Curie temperature relationships in BaTiO 3 -based ferroelectric

  14. Grain boundary junctions of FeSe0.5Te0.5 thin films on SrTiO3...

    Office of Scientific and Technical Information (OSTI)

    Matter Physics and Materials Science Department, Brookhaven National Laboratory, Upton, New York 11973, USA National High Magnetic Field Laboratory, Florida State University,...

  15. Coating power RF components with TiN

    SciTech Connect (OSTI)

    Kuchnir, M.; Hahn, E.

    1995-03-01

    A facility for coating RF power components with thin films of Ti and/or TiN has been in operation for some time at Fermilab supporting the Accelerator Division RF development work and the TESLA program. It has been experimentally verified that such coatings improve the performance of these components as far as withstanding higher electric fields. This is attributed to a reduction in the secondary electron emission coefficient of the surfaces when coated with a thin film containing titanium. The purpose of this Technical Memorandum is to describe the facility and the procedure used.

  16. High strength, light weight Ti-Y composites and method of making same

    DOE Patents [OSTI]

    Verhoeven, John D.; Ellis, Timothy W.; Russell, Alan M.; Jones, Lawrence L.

    1993-04-06

    A high strength, light weight "in-situ" Ti-Y composite is produced by deformation processing a cast body having Ti and Y phase components distributed therein. The composite comprises elongated, ribbon-shaped Ti and Y phase components aligned along an axis of the deformed body.

  17. High strength, light weight Ti-Y composites and method of making same

    DOE Patents [OSTI]

    Verhoeven, J.D.; Ellis, T.W.; Russell, A.M.; Jones, L.L.

    1993-04-06

    A high strength, light weight in-situ'' Ti-Y composite is produced by deformation processing a cast body having Ti and Y phase components distributed therein. The composite comprises elongated, ribbon-shaped Ti and Y phase components aligned along an axis of the deformed body.

  18. Experimental Realization of a Three-Dimensional Topological Insulator, Bi 2Te3

    SciTech Connect (OSTI)

    Siemons, W.

    2010-02-24

    Three-dimensional topological insulators are a new state of quantum matter with a bulk gap and odd number of relativistic Dirac fermions on the surface. By investigating the surface state of Bi{sub 2}Te{sub 3} with angle-resolved photoemission spectroscopy, we demonstrate that the surface state consists of a single nondegenerate Dirac cone. Furthermore, with appropriate hole doping, the Fermi level can be tuned to intersect only the surface states, indicating a full energy gap for the bulk states. Our results establish that Bi{sub 2}Te{sub 3} is a simple model system for the three-dimensional topological insulator with a single Dirac cone on the surface. The large bulk gap of Bi{sub 2}Te{sub 3} also points to promising potential for high-temperature spintronics applications.

  19. Systematic study of doping dependence on linear magnetoresistance in p-PbTe

    SciTech Connect (OSTI)

    Schneider, J. M.; Chitta, V. A.; Oliveira, N. F.; Peres, M. L. Castro, S. de; Soares, D. A. W.; Wiedmann, S.; Zeitler, U.; Abramof, E.; Rappl, P. H. O.; Mengui, U. A.

    2014-10-20

    We report on a large linear magnetoresistance effect observed in doped p-PbTe films. While undoped p-PbTe reveals a sublinear magnetoresistance, p-PbTe films doped with BaF{sub 2} exhibit a transition to a nearly perfect linear magnetoresistance behaviour that is persistent up to 30?T. The linear magnetoresistance slope ?R/?B is to a good approximation, independent of temperature. This is in agreement with the theory of Quantum Linear Magnetoresistance. We also performed magnetoresistance simulations using a classical model of linear magnetoresistance. We found that this model fails to explain the experimental data. A systematic study of the doping dependence reveals that the linear magnetoresistance response has a maximum for small BaF{sub 2} doping levels and diminishes rapidly for increasing doping levels. Exploiting the huge impact of doping on the linear magnetoresistance signal could lead to new classes of devices with giant magnetoresistance behavior.

  20. Ba{sub 2}TeO as an optoelectronic material: First-principles study

    SciTech Connect (OSTI)

    Sun, Jifeng; Shi, Hongliang; Du, Mao-Hua; Singh, David J.; Siegrist, Theo

    2015-05-21

    The band structure, optical, and defects properties of Ba{sub 2}TeO are systematically investigated using density functional theory with a view to understanding its potential as an optoelectronic or transparent conducting material. Ba{sub 2}TeO crystallizes with tetragonal structure (space group P4/nmm) and with a 2.93 eV optical bandgap [Besara et al., J. Solid State Chem. 222, 60 (2015)]. We find relatively modest band masses for both electrons and holes suggesting applications. Optical properties show infrared-red absorption when doped. This could potentially be useful for combining wavelength filtering and transparent conducting functions. Furthermore, our defect calculations show that Ba{sub 2}TeO is intrinsically p-type conducting under Ba-poor condition. However, the spontaneous formation of the donor defects may constrain the p-type transport properties and would need to be addressed to enable applications.

  1. Pair correlations in neutrinoless double {beta} decay candidate {sup 130}Te.

    SciTech Connect (OSTI)

    Bloxham, T.; Kay, B. P.; Schiffer, J. P.; Clark, J. A.; Deibel, C. M.; Freeman, S. J.; Freedman, S. J.; Howard, A. M.; McAllister, S. A.; Parker, P. D.; Sharp, D. K.; Thomas, J. S. (Physics); ( PSC-USR); (LBNL); (Michigan State Univ.); (Univ. of Manchester); (Yale Univ.)

    2010-08-16

    Pair correlations in the ground state of {sup 130}Te have been investigated using pair-transfer experiments to explore the validity of approximations in calculating the matrix element for neutrinoless double-{beta} decay. This nucleus is a candidate for the observation of such decay, and a good understanding of its structure is crucial for eventual calculations of the neutrino mass, should such a decay indeed be observed. For proton-pair adding, strong transitions to excited 0{sup +} states had been observed in the Te isotopes by Alford et al. [Nucl. Phys. A 323, 339 (1979)], indicating a breaking of the BCS approximation for protons in the ground state. We measured the neutron-pair removing (p,t) reaction on {sup 130}Te and found no indication of a corresponding splitting of the BCS nature of the ground state for neutrons.

  2. Pair correlations in the neutrinoless double-{beta} decay candidate {sup 130}Te

    SciTech Connect (OSTI)

    Bloxham, T.; Freedman, S. J. [Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Kay, B. P.; Schiffer, J. P.; Clark, J. A. [Physics Division, Argonne National Laboratory, Argonne, Illinois 60439 (United States); Deibel, C. M. [Physics Division, Argonne National Laboratory, Argonne, Illinois 60439 (United States); Joint Institute for Nuclear Astrophysics, Michigan State University, East Lansing, Michigan 48825 (United States); Freeman, S. J.; Howard, A. M.; McAllister, S. A.; Sharp, D. K.; Thomas, J. S. [Schuster Laboratory, University of Manchester, Manchester, M13 9PL (United Kingdom); Parker, P. D. [A. W. Wright Nuclear Structure Laboratory, Yale University, New Haven, Connecticut 06520 (United States)

    2010-08-15

    Pair correlations in the ground state of {sup 130}Te have been investigated using pair-transfer experiments to explore the validity of approximations in calculating the matrix element for neutrinoless double-{beta} decay. This nucleus is a candidate for the observation of such decay, and a good understanding of its structure is crucial for eventual calculations of the neutrino mass, should such a decay indeed be observed. For proton-pair adding, strong transitions to excited 0{sup +} states had been observed in the Te isotopes by Alford et al. [Nucl. Phys. A 323, 339 (1979)], indicating a breaking of the BCS approximation for protons in the ground state. We measured the neutron-pair removing (p,t) reaction on {sup 130}Te and found no indication of a corresponding splitting of the BCS nature of the ground state for neutrons.

  3. Superconducting thin films of (100) and (111) oriented indium doped topological crystalline insulator SnTe

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Si, W.; Zhang, C.; Wu, L.; Ozaki, T.; Gu, G.; Li, Q.

    2015-09-01

    Recent discovery of the topological crystalline insulator SnTe has triggered a search for topological superconductors, which have potential application to topological quantum computing. The present work reports on the superconducting properties of indium doped SnTe thin films. The (100) and (111) oriented thin films were epitaxially grown by pulsed-laser deposition on (100) and (111) BaF2 crystalline substrates respectively. The onset superconducting transition temperatures are about 3.8 K for (100) and 3.6 K for (111) orientations, slightly lower than that of the bulk. Magneto-resistive measurements indicate that these thin films may have upper critical fields higher than that of the bulk.more » With large surface-to-bulk ratio, superconducting indium doped SnTe thin films provide a rich platform for the study of topological superconductivity and potential device applications based on topological superconductors.« less

  4. Simulation of Electric Field in Semi Insulating Au/CdTe/Au Detector under Flux

    SciTech Connect (OSTI)

    Franc, J.; James, R.; Grill, R.; Kubat, J.; Belas, E.; Hoschl, P.; Moravec, P.; Praus, P.

    2009-08-02

    We report our simulations on the profile of the electric field in semi insulating CdTe and CdZnTe with Au contacts under radiation flux. The type of the space charge and electric field distribution in the Au/CdTe/Au structure is at high fluxes result of a combined influence of charge formed due to band bending at the electrodes and from photo generated carriers, which are trapped at deep levels. Simultaneous solution of drift-diffusion and Poisson equations is used for the calculation. We show, that the space charge originating from trapped photo-carriers starts to dominate at fluxes 10{sup 15}-10{sup 16}cm{sup -2}s{sup -1}, when the influence of contacts starts to be negligible.

  5. Role of polycrystallinity in CdTe and CuInSe sub 2 photovoltaic cells

    SciTech Connect (OSTI)

    Sites, J.R. )

    1991-01-01

    The polycrystalline nature of thin-film CdTe and CuInSe{sub 2} solar cells continues to be a major factor in several individual losses that limit overall cell efficiency. This report describes progress in the quantitative separation of these losses, including both measurement and analysis procedures. It also applies these techniques to several individual cells to help document the overall progress with CdTe and CuInSe{sub 2} cells. Notably, CdTe cells from Photon Energy have reduced window photocurrent losses to 1 mA/Cm{sup 2}; those from the University of South Florida have achieved a maximum power voltage of 693 mV; and CuInSe{sub 2} cells from International Solar Electric Technology have shown a hole density as high as 7 {times} 10{sup 16} cm{sup {minus}3}, implying a significant reduction in compensation. 9 refs.

  6. Thermoelectric study of crossroads material MnTe via sulfur doping

    SciTech Connect (OSTI)

    Xie, Wenjie Populoh, Sascha; Sagarna, Leyre; Trottmann, Matthias; Ga??zka, Krzysztof; Xiao, Xingxing; Liu, Yufei; He, Jian; Weidenkaff, Anke

    2014-03-14

    Here, we report thermoelectric study of crossroads material MnTe via iso-electronic doping S on the Te-site. MnTe{sub 1-x}S{sub x} samples with nominal S content of x?=?0.00, 0.05, and 0.10 were prepared using a melt-quench method followed by pulverization and spark plasma sintering. The X-ray powder diffraction, scanning electron microscopy, and ZAF-corrected compositional analysis confirmed that S uniformly substitutes Te up to slightly over 2%. A higher content of S in the starting materials led to the formation of secondary phases. The thermoelectric properties of MnTe{sub 1-x}S{sub x} samples were characterized by means of Seebeck coefficient, electrical conductivity, and thermal conductivity measurements from 300?K to 773?K. Furthermore, Hall coefficient measurements and a single parabolic band model were used to help gain insights on the effects of S-doping on the scattering mechanism and the carrier effective mass. As expected, S doping not only introduced hole charge carriers but also created short-range defects that effectively scatter heat-carrying phonons at elevated temperatures. On the other hand, we found that S doping degraded the effective mass. As a result, the ZT of MnTe{sub 0.9}S{sub 0.1} was substantially enhanced over the pristine sample near 400?K, while the improvement of ZT became marginal at elevated temperatures. A ZT???0.65 at 773?K was obtained in all three samples.

  7. Synthesis, crystal and electronic structure, and physical properties of the new lanthanum copper telluride La{sub 3}Cu{sub 5}Te{sub 7}

    SciTech Connect (OSTI)

    Zelinska, Mariya; Assoud, Abdeljalil [Department of Chemistry, University of Waterloo, Waterloo, ON, Canada N2L 3G1 (Canada); Kleinke, Holger, E-mail: kleinke@uwaterloo.c [Department of Chemistry, University of Waterloo, Waterloo, ON, Canada N2L 3G1 (Canada)

    2011-03-15

    The new lanthanum copper telluride La{sub 3}Cu{sub 5-x}Te{sub 7} has been obtained by annealing the elements at 1073 K. Single-crystal X-ray diffraction studies revealed that the title compound crystallizes in a new structure type, space group Pnma (no. 62) with lattice dimensions of a=8.2326(3) A, b=25.9466(9) A, c=7.3402(3) A, V=1567.9(1) A{sup 3}, Z=4 for La{sub 3}Cu{sub 4.86(4)}Te{sub 7}. The structure of La{sub 3}Cu{sub 5-x}Te{sub 7} is remarkably complex. The Cu and Te atoms build up a three-dimensional covalent network. The coordination polyhedra include trigonal LaTe{sub 6} prisms, capped trigonal LaTe{sub 7} prisms, CuTe{sub 4} tetrahedra, and CuTe{sub 3} pyramids. All Cu sites exhibit deficiencies of various extents. Electrical property measurements on a sintered pellet of La{sub 3}Cu{sub 4.86}Te{sub 7} indicate that it is a p-type semiconductor in accordance with the electronic structure calculations. -- Graphical abstract: Oligomeric unit comprising interconnected CuTe{sub 3} pyramids and CuTe{sub 4} tetrahedra. Display Omitted Research highlights: {yields} La{sub 3}Cu{sub 5-x}Te{sub 7} adopts a new structure type. {yields} All Cu sites exhibit deficiencies of various extents. {yields} The coordination polyhedra include trigonal LaTe{sub 6} prisms, capped trigonal LaTe{sub 7} prisms, CuTe{sub 4} tetrahedra and CuTe{sub 3} pyramids. {yields} La{sub 3}Cu{sub 5-x}Te{sub 7} is a p-type semiconductor.

  8. Multiband Te p Based Superconductivity of Ta4Pd3Te16

    SciTech Connect (OSTI)

    Singh, David J.

    2014-10-06

    We recently discovered that Ta4Pd3Te16 is a superconductor that has been suggested to be an unconventional superconductor near magnetism. Here, we report electronic structure calculations showing that despite the layered crystal structure the material is an anisotropic three-dimensional (3D) metal. The Fermi surface contains prominent one-dimensional (1D) and two-dimensional (2D) features, including nested 1D sheets, a 2D cylindrical section, and a 3D sheet. Moreover, the electronic states that make up the Fermi surface are mostly derived from Te p states with small Ta d and Pd d contributions. This places the compound far from magnetic instabilities. The results are discussed in terms of multiband superconductivity.

  9. Passivation of an isoelectronic impurity by atomic hydrogen: The case of ZnTe:O

    SciTech Connect (OSTI)

    Felici, Marco; Polimeni, Antonio; Capizzi, Mario; Nabetani, Y.; Okuno, T.; Aoki, K.; Kato, T.; Matsumoto, T.; Hirai, T.

    2006-03-06

    We investigated the optical properties of ZnTe:O/GaAs before and after atomic hydrogen irradiation. Oxygen incorporation gives rise to energy levels associated with single O atoms, O-O pairs, and O clusters, and to a blueshift of the energy gap of the material with respect to that of pure ZnTe/GaAs. All of these effects disappear progressively after irradiation with H, which also leads to an increase in the tensile strain of the epilayer. These observations provide experimental evidence of H-induced passivation of an isoelectronic impurity in II-VI alloys.

  10. Emission switching in carbon dots coated CdTe quantum dots driving by pH

    Office of Scientific and Technical Information (OSTI)

    dependent hetero-interactions (Journal Article) | SciTech Connect Emission switching in carbon dots coated CdTe quantum dots driving by pH dependent hetero-interactions Citation Details In-Document Search Title: Emission switching in carbon dots coated CdTe quantum dots driving by pH dependent hetero-interactions Due to the different emission mechanism between fluorescent carbon dots and semiconductor quantum dots (QDs), it is of interest to explore the potential emission in

  11. Energy Sources for Yotta-TeV Iceberg Showers (Conference) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Energy Sources for Yotta-TeV Iceberg Showers Citation Details In-Document Search Title: Energy Sources for Yotta-TeV Iceberg Showers In late February of 2002, warming climate along the Antarctic Peninsula triggered a macroscopic particle acceleration event that smashed a 350 Gkg floating ice shelf, called the Larsen B. The particle shower released by the acceleration involved on the order of >10^6 iceberg particles accelerated to an aggregate total kinetic energy of ~10^17 J (100 Mt TNT

  12. Higgs production and decay from TeV scale black holes at the LHC (Journal

    Office of Scientific and Technical Information (OSTI)

    Article) | SciTech Connect Higgs production and decay from TeV scale black holes at the LHC Citation Details In-Document Search Title: Higgs production and decay from TeV scale black holes at the LHC We perform a detailed study of the Higgs production and decay, when Higgs is emitted from the black holes produced in proton-proton collisions at the Large Hadron Collider. We show that black hole production can significantly enhance the signal for the Higgs search at the LHC. We evaluate

  13. Preliminary design for a 20 TeV Collider in a deep tunnel at Fermilab

    SciTech Connect (OSTI)

    Not Available

    1985-01-12

    The Reference Design Study for a 20 TeV Collider demonstrated the technical and cost feasibility of a 20 TeV superconducting collider facility. Based on magnets of 3T, 5T, and 6.5T the Main Ring of the Collider would have a circumference of 164 km, 113 km, or 90 km. There would be six collision regions, of which four would be developed intially. The 5T and 6.5T rings would have twelve major refrigeration stations, while the 3T design would have 24 major refrigeration stations.

  14. Indexing and TEM Sample Preparation of Isolated CdTe/CdS Nano-Islands.

    Office of Scientific and Technical Information (OSTI)

    (Conference) | SciTech Connect Conference: Indexing and TEM Sample Preparation of Isolated CdTe/CdS Nano-Islands. Citation Details In-Document Search Title: Indexing and TEM Sample Preparation of Isolated CdTe/CdS Nano-Islands. Abstract not provided. Authors: Aguirre, Brandon Adrian ; Cruz-Campa, Jose Luis ; Jungjohann, Katherine Leigh ; Pete, Douglas V. ; Zubia, David Publication Date: 2014-03-01 OSTI Identifier: 1140918 Report Number(s): SAND2014-2312C 505756 DOE Contract Number:

  15. Intrinsic Surface Passivation of CdTe (Journal Article) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Intrinsic Surface Passivation of CdTe Citation Details In-Document Search Title: Intrinsic Surface Passivation of CdTe Authors: Reese, Matthew O. ; Perkins, Craig L. ; Burst, James M. ; Farrell, Stuart ; Barnes, Teresa M. ; Johnston, Steve W. ; Kuciauskas, Darius ; Gessert, Timothy A. ; Metzger, Wyatt K. Publication Date: 2015-10-21 OSTI Identifier: 1225933 Report Number(s): NREL/JA-5K00-64478 Journal ID: ISSN 0021-8979 DOE Contract Number: AC36-08GO28308 Resource Type: Journal Article Resource

  16. Shape-controlled narrow-gap SnTe nanostructures: From nanocubes to nanorods

    Office of Scientific and Technical Information (OSTI)

    and nanowires (Journal Article) | SciTech Connect Shape-controlled narrow-gap SnTe nanostructures: From nanocubes to nanorods and nanowires Citation Details In-Document Search This content will become publicly available on November 6, 2016 Title: Shape-controlled narrow-gap SnTe nanostructures: From nanocubes to nanorods and nanowires In this study, the rational design and synthesis of narrow-gap colloidal semiconductor nanocrystals (NCs) is an important step toward the next generation of

  17. Renaissance of the ~1 TeV Fixed-Target Program

    SciTech Connect (OSTI)

    Adams, T.; Appel, Jeffrey A.; Arms, Kregg Elliott; Balantekin, A.B.; Conrad, Janet Marie; Cooper, Peter S.; Djurcic, Zelimir; Dunwoodie, William M.; Engelfried, Jurgen; Fisher, Peter H.; Gottschalk, E.; /Fermilab /Northwestern U.

    2009-05-01

    This document describes the physics potential of a new fixed-target program based on a {approx} TeV proton source. Two proton sources are potentially available in the future: the existing Tevatron at Fermilab, which can provide 800 GeV protons for fixed-target physics, and a possible upgrade to the SPS at CERN, called SPS+, which would produce 1 TeV protons on target. In this paper we use an example Tevatron fixed-target program to illustrate the high discovery potential possible in the charm and neutrino sectors. We highlight examples which are either unique to the program or difficult to accomplish at other venues.

  18. Renaissance of the ~ 1-TeV Fixed-Target Program

    SciTech Connect (OSTI)

    Adams, T.; Appel, J.A.; Arms, K.E.; Balantekin, A.B.; Conrad, J.M.; Cooper, P.S.; Djurcic, Z.; Dunwoodie, W.; Engelfried, J.; Fisher, P.H.; Gottschalk, Erik Edward; de Gouvea, A.; Heller, K.; Ignarra, C.M.; Karagiorgi, G.; Kwan, S.; Loinaz, W.A.; Meadows, B.; Moore, R.; Morfin, J.G.; Naples, D.; /Pittsburgh U. /St. Mary's Coll., Minnesota /New Mexico State U. /Michigan U. /Wayne State U. /South Carolina U. /Florida U. /Carnegie Mellon U. /Cincinnati U. /Columbia U. /Columbia U. /Northwestern U. /Yale U. /Fermilab /Argonne /Northwestern U. /APC, Paris

    2011-12-02

    This document describes the physics potential of a new fixed-target program based on a {approx}1 TeV proton source. Two proton sources are potentially available in the future: the existing Tevatron at Fermilab, which can provide 800 GeV protons for fixed-target physics, and a possible upgrade to the SPS at CERN, called SPS+, which would produce 1 TeV protons on target. In this paper we use an example Tevatron fixed-target program to illustrate the high discovery potential possible in the charm and neutrino sectors. We highlight examples which are either unique to the program or difficult to accomplish at other venues.

  19. Ultrafast Terahertz-Induced Response of GeSbTe Phase-Change Materials

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect Terahertz-Induced Response of GeSbTe Phase-Change Materials Citation Details In-Document Search Title: Ultrafast Terahertz-Induced Response of GeSbTe Phase-Change Materials × You are accessing a document from the Department of Energy's (DOE) SciTech Connect. This site is a product of DOE's Office of Scientific and Technical Information (OSTI) and is provided as a public service. Visit OSTI to utilize additional information resources in energy science and

  20. Graphene/CdTe heterostructure solar cell and its enhancement with photo-induced doping

    SciTech Connect (OSTI)

    Lin, Shisheng Chen, Hongsheng; Li, Xiaoqiang; Zhang, Shengjiao; Wang, Peng; Xu, Zhijuan; Zhong, Huikai; Wu, Zhiqian

    2015-11-09

    We report a type of solar cell based on graphene/CdTe Schottky heterostructure, which can be improved by surface engineering as graphene is atomic thin. By coating a layer of ultrathin CdSe quantum dots onto graphene/CdTe heterostructure, the power conversion efficiency is increased from 2.08% to 3.10%. Photo-induced doping is mainly accounted for this enhancement, as evidenced by field effect transport, Raman, photoluminescence, and quantum efficiency measurements. This work demonstrates a feasible way of improving the performance of graphene/semiconductor heterostructure solar cells by combining one dimensional with two dimensional materials.

  1. Charged-particle distributions in s=13 TeV pp interactions measured with

    Office of Scientific and Technical Information (OSTI)

    the ATLAS detector at the LHC (Journal Article) | SciTech Connect Charged-particle distributions in s = 13 TeV pp interactions measured with the ATLAS detector at the LHC Citation Details In-Document Search Title: Charged-particle distributions in s = 13 TeV pp interactions measured with the ATLAS detector at the LHC Publication Date: 2016-07-01 OSTI Identifier: 1250307 Type: Published Article Journal Name: Physics Letters. Section B Additional Journal Information: Journal Volume: 758;

  2. Aqueous Synthesis of Zinc Blende CdTe/CdS Magic-Core/Thick-Shell

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tetrahedral Shaped Nanocrystals with Emission Tunable to Near-Infrared Aqueous Synthesis of Zinc Blende CdTe/CdS Magic-Core/Thick-Shell Tetrahedral Shaped Nanocrystals with Emission Tunable to Near-Infrared Authors: Deng, Z., Schulz, O., Lin, S., Ding, B., Liu, X., Wei, X., Ros, R., Liu, Y., Yan, H., and Francis, M. Title: Aqueous Synthesis of Zinc Blende CdTe/CdS Magic-Core/Thick-Shell Tetrahedral Shaped Nanocrystals with Emission Tunable to Near-Infrared Source: Journal of the American

  3. .sup.123m Te-Labeled biochemicals and method of preparation

    DOE Patents [OSTI]

    Knapp, Jr., Furn F.

    1980-01-01

    A novel class of .sup.123m Te-labeled steroids and amino acids is provided by the method of reacting a .sup.123m Te symmetric diorgano ditelluride with a hydride reducing agent and a source of alkali metal ions to form an alkali metal organo telluride. The alkali metal organo telluride is reacted with a primary halogenated steroidal side chain, amino acid, or amino acid precursor such as hydantoin. The novel compounds are useful as biological tracers and as organal imaging agents.

  4. High efficiency thin film CdTe and a-Si based solar cells

    SciTech Connect (OSTI)

    Compaan, A. D.; Deng, X.; Bohn, R. G.

    2000-01-04

    This report describes work done by the University of Toledo during the first year of this subcontract. During this time, the CdTe group constructed a second dual magnetron sputter deposition facility; optimized reactive sputtering for ZnTe:N films to achieve 10 ohm-cm resistivity and {approximately}9% efficiency cells with a copper-free ZnTe:N/Ni contact; identified Cu-related photoluminescence features and studied their correlation with cell performance including their dependence on temperature and E-fields; studied band-tail absorption in CdS{sub x}Te{sub 1{minus}x} films at 10 K and 300 K; collaborated with the National CdTe PV Team on (1) studies of high-resistivity tin oxide (HRT) layers from ITN Energy Systems, (2) fabrication of cells on the HRT layers with 0, 300, and 800-nm CdS, and (3) preparation of ZnTe:N-based contacts on First Solar materials for stress testing; and collaborated with Brooklyn College for ellipsometry studies of CdS{sub x}Te{sub 1{minus}x} alloy films, and with the University of Buffalo/Brookhaven NSLS for synchrotron X-ray fluorescence studies of interdiffusion in CdS/CdTe bilayers. The a-Si group established a baseline for fabricating a-Si-based solar cells with single, tandem, and triple-junction structures; fabricated a-Si/a-SiGe/a-SiGe triple-junction solar cells with an initial efficiency of 9.7% during the second quarter, and 10.6% during the fourth quarter (after 1166 hours of light-soaking under 1-sun light intensity at 50 C, the 10.6% solar cells stabilized at about 9%); fabricated wide-bandgap a-Si top cells, the highest Voc achieved for the single-junction top cell was 1.02 V, and top cells with high FF (up to 74%) were fabricated routinely; fabricated high-quality narrow-bandgap a-SiGe solar cells with 8.3% efficiency; found that bandgap-graded buffer layers improve the performance (Voc and FF) of the narrow-bandgap a-SiGe bottom cells; and found that a small amount of oxygen partial pressure ({approximately}2 {times} 10{sup {minus}5} torr) was beneficial for growing high-quality films from ITO targets.

  5. Charge transport properties of p-CdTe/n-CdTe/n{sup +}-Si diode-type nuclear radiation detectors based on metalorganic vapor-phase epitaxy-grown epilayers

    SciTech Connect (OSTI)

    Niraula, M.; Yasuda, K.; Wajima, Y.; Yamashita, H.; Tsukamoto, Y.; Suzuki, Y.; Matsumoto, M.; Takai, N.; Tsukamoto, Y.; Agata, Y.

    2013-10-28

    Charge transport properties of p-CdTe/n-CdTe/n{sup +}-Si diode-type nuclear radiation detectors, fabricated by growing p-and n-type CdTe epilayers on (211) n{sup +}-Si substrates using metalorganic vapor-phase epitaxy (MOVPE), were studied by analyzing current-voltage characteristics measured at various temperatures. The diode fabricated shows good rectification properties, however, both forward and reverse biased currents deviate from their ideal behavior. The forward current exhibits typical feature of multi-step tunneling at lower biases; however, becomes space charge limited type when the bias is increased. On the other hand, the reverse current exhibits thermally activated tunneling-type current. It was found that trapping centers at the p-CdTe/n-CdTe junction, which were formed due to the growth induced defects, determine the currents of this diode, and hence limit the performance of the nuclear radiation detectors developed.

  6. Hysteretic electrical transport in BaTiO{sub 3}/Ba{sub 1?x}Sr{sub x}TiO{sub 3}/Ge heterostructures

    SciTech Connect (OSTI)

    Ngai, J. H.; Kumah, D. P.; Walker, F. J.; Ahn, C. H.

    2014-02-10

    We present electrical transport measurements of heterostructures comprised of BaTiO{sub 3} and Ba{sub 1?x}Sr{sub x}TiO{sub 3} epitaxially grown on Ge. Sr alloying imparts compressive strain to the BaTiO{sub 3}, which enables the thermal expansion mismatch between BaTiO{sub 3} and Ge to be overcome to achieve c-axis oriented growth. The conduction bands of BaTiO{sub 3} and Ba{sub 1?x}Sr{sub x}TiO{sub 3} are nearly aligned with the conduction band of Ge, which facilitates electron transport. Electrical transport measurements through the dielectric stack exhibit rectifying behavior and hysteresis, where the latter is consistent with ferroelectric switching.

  7. Induced Ti magnetization at La0.7Sr0.3MnO3 and BaTiO3 interfaces

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Liu, Yaohua; Tornos, J.; te Velthuis, S. G. E.; Freeland, J. W.; Zhou, H.; Steadman, P.; Bencok, P.; Leon, C.; Santamaria, J.

    2016-04-01

    In artificial multiferroics hybrids consisting of ferromagnetic La0.7Sr0.3MnO3 (LSMO) and ferroelectric BaTiO3 epitaxial layers, net Ti moments are found from polarized resonant soft x-ray reflectivity and absorption. Moreover, the Ti dichroic reflectivity follows the Mn signal during the magnetization reversal, indicating exchange coupling between the Ti and Mn ions. But, the Ti dichroic reflectivity shows stronger temperature dependence than the Mn dichroic signal. Besides a reduced ferromagnetic exchange coupling in the interfacial LSMO layer, this may also be attributed to a weak Ti-Mn exchange coupling that is insufficient to overcome the thermal energy at elevated temperatures.

  8. Search for a very light NMSSM Higgs boson produced in decays of the 125 GeV scalar boson and decaying into $\\tau$ leptons in pp collisions at $\\sqrt{s} =$ 8 TeV

    SciTech Connect (OSTI)

    Khachatryan, Vardan

    2015-10-23

    Our search for a very light Higgs boson decaying into a pair of t leptons is presented within the framework of the next-to-minimal supersymmetric standard model. This search is based on a data set corresponding to an integrated luminosity of 19.7 fb-1 of proton-proton collisions collected by the CMS experiment at a centre-of-mass energy of 8 TeV. The signal is defined by the production of either of the two lightest scalars, h1 or h2, via gluon-gluon fusion and subsequent decay into a pair of the lightest Higgs bosons, a1 or h1. The h1 or h2 boson is identified with the observed state at a mass of 125 GeV. The analysis searches for decays of the a1 (h1) states into pairs of t leptons and covers a mass range for the a1 (h1) boson of 4 to 8 GeV. Furthermore, the search reveals no significant excess in data above standard model background expectations, and an upper limit is set on the signal production cross section times branching fraction as a function of the a1 (h1) boson mass. The 95% confidence level limit ranges from 4.5 pb at ma1 (mh1 ) = 8 GeV to 10.3 pb at ma1 (mh1 ) = 5 GeV.

  9. Local-moment magnetism in superconducting FeTe0.35Se0.65 as seen...

    Office of Scientific and Technical Information (OSTI)

    Local-moment magnetism in superconducting FeTe0.35Se0.65 as seen via inelastic neutron scattering Prev Next Title: Local-moment magnetism in superconducting FeTe0.35Se0.65 as ...

  10. Study of W boson production in pPb collisions at sNN=5.02 TeV...

    Office of Scientific and Technical Information (OSTI)

    Study of W boson production in pPb collisions at sNN5.02 TeV Citation Details In-Document Search Title: Study of W boson production in pPb collisions at sNN5.02 TeV Publication...

  11. Cadmium sulfate and CdTe-quantum dots alter DNA repair in zebrafish (Danio rerio) liver cells

    SciTech Connect (OSTI)

    Tang, Song; Cai, Qingsong; Chibli, Hicham; Allagadda, Vinay; Nadeau, Jay L.; Mayer, Gregory D.

    2013-10-15

    Increasing use of quantum dots (QDs) makes it necessary to evaluate their toxicological impacts on aquatic organisms, since their contamination of surface water is inevitable. This study compares the genotoxic effects of ionic Cd versus CdTe nanocrystals in zebrafish hepatocytes. After 24 h of CdSO{sub 4} or CdTe QD exposure, zebrafish liver (ZFL) cells showed a decreased number of viable cells, an accumulation of Cd, an increased formation of reactive oxygen species (ROS), and an induction of DNA strand breaks. Measured levels of stress defense and DNA repair genes were elevated in both cases. However, removal of bulky DNA adducts by nucleotide excision repair (NER) was inhibited with CdSO{sub 4} but not with CdTe QDs. The adverse effects caused by acute exposure of CdTe QDs might be mediated through differing mechanisms than those resulting from ionic cadmium toxicity, and studying the effects of metallic components may be not enough to explain QD toxicities in aquatic organisms. - Highlights: Both CdSO{sub 4} and CdTe QDs lead to cell death and Cd accumulation. Both CdSO{sub 4} and CdTe QDs induce cellular ROS generation and DNA strand breaks. Both CdSO{sub 4} and CdTe QDs induce the expressions of stress defense and DNA repair genes. NER repair capacity was inhibited with CdSO{sub 4} but not with CdTe QDs.

  12. Sonochemical and hydrothermal synthesis of PbTe nanostructures with the aid of a novel capping agent

    SciTech Connect (OSTI)

    Fard-Fini, Shahla Ahmadian; Salavati-Niasari, Masoud; Mohandes, Fatemeh

    2013-10-15

    Graphical abstract: - Highlights: • PbTe nanostructures were prepared with the aid of Schiff-base compound. • Sonochemical and hydrothermal methods were employed to fabricate PbTe nanostrucrues. • The effect of preparation parameters on the morphology of PbTe was investigated. - Abstract: In this work, a new Schiff-base compound derived from 1,8-diamino-3,6-dioxaoctane and 2-hydroxy-1-naphthaldehyde marked as (2-HyNa)-(DaDo) was synthesized, characterized, and then used as capping agent for the preparation of PbTe nanostructures. To fabricate PbTe nanostructures, two different synthesis methods; hydrothermal and sonochemical routes, were applied. To further investigate, the effect of preparation parameters like reaction time and temperature in hydrothermal synthesis and sonication time in the presence of ultrasound irradiation on the morphology and purity of the final products was tested. The products were analyzed with the aid of SEM, TEM, XRD, FT-IR, and EDS. Based on the obtained results, it was found that pure cubic phased PbTe nanostructures have been obtained by hydrothermal and sonochemical approaches. Besides, SEM images showed that cubic-like and rod-like PbTe nanostructures have been formed by hydrothermal and sonochemical methods, respectively. Sonochemical synthesis of PbTe nanostructures was favorable, because the synthesis time of sonochemical method was shorter than that of hydrothermal method.

  13. Adhesion evaluation of TiN and (Ti, Al)N coatings on titanium 6Al-4V

    SciTech Connect (OSTI)

    James, R.D.; Gruss, K.A.; Horie, Y.; Davis, R.F.; Paisley, D.L.; Parthasarthi, S.; Tittmann, B.R.

    1996-12-31

    The metallic components of gas turbine engines are continually subjected to hostile atmospheres. Nitride coatings improve the performance of the metallic compressor blades in these engines. To assess the adhesion of nitride coatings on metals, titanium 6% aluminum 4% vanadium substrates were coated with titanium nitride (TiN) using both cathodic arc and electron beam evaporation. Titanium aluminum nitride ((Ti, Al)N) was also deposited using cathodic arc evaporation. The interfaces of the coated samples were loaded in tension using a high speed shock wave which caused spallation either at the interface, in the coating or in the metal. Scanning acoustic microscopy analysis of the spalled samples detected delaminations at the interface in the samples deposited by cathodic arc evaporation. DYNA2D modeling of plate impact spallation experiments revealed the tensile adhesion strength for TiN deposited by both techniques was {approx} 2.0 GPa. The tensile adhesion strength for (Ti, Al)N was less than 1.5 GPa.

  14. Laser hydrothermal reductive ablation of titanium monoxide: Hydrated TiO particles with modified Ti/O surface

    SciTech Connect (OSTI)

    Blazevska-Gilev, Jadranka; Jandova, Vera; Kupcik, Jaroslav; Bastl, Zdenek; Subrt, Jan; Bezdicka, Petr; Pola, Josef

    2013-01-15

    IR laser- and UV laser-induced ablation of titanium monoxide (TM) in hydrogen (50 Torr) is compared to the same process induced in vacuum and shown to result in deposition of hydrated surface modified nanostructured titanium suboxide films. Complementary analyses of the films deposited in vacuum and in hydrogen by Fourier transform infrared, Raman and X-ray photoelectron spectroscopy, X-ray diffraction and electron microscopy allowed to determine different features of both films and propose a mechanism of surface modification of ejected particles, which involves hydrothermal reduction of TM and subsequent reactions of evolved water. The films exert good adhesion to metal and quartz surfaces and are hydrophobic in spite of having their surface coated with adsorbed water. - Graphical abstract: Laser ablation of titanium monoxide (TiO) in hydrogen involves a sequence of H{sub 2} and H{sub 2}O eliminations and additions and yields hydrated amorphous nanostructured titanium suboxide which is richer in oxygen than TiO. Highlights: Black-Right-Pointing-Pointer IR and UV laser ablated particles of titanium monoxide (TiO) undergo amorphization. Black-Right-Pointing-Pointer Films deposited in vacuum have TiO stoichiometry and are oxidized in atmosphere. Black-Right-Pointing-Pointer Films deposited in hydrogen are hydrated and have more O in topmost layers. Black-Right-Pointing-Pointer Films modification in hydrogen is explained by reactions in hydrogen plasma.

  15. Shape-controlled narrow-gap SnTe nanostructures: From nanocubes to nanorods and nanowires

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Guo, Shaojun; Andrew F. Fidler; He, Kai; Su, Dong; Chen, Gen; Lin, Qianglu; Pietryga, Jeffrey M.; Klimov, Victor I.

    2015-11-06

    In this study, the rational design and synthesis of narrow-gap colloidal semiconductor nanocrystals (NCs) is an important step toward the next generation of solution-processable photovoltaics, photodetectors, and thermoelectric devices. SnTe NCs are particularly attractive as a Pb-free alternative to NCs of narrow-gap lead chalcogenides. Previous synthetic efforts on SnTe NCs have focused on spherical nanoparticles. Here we report new strategies for synthesis of SnTe NCs with shapes tunable from highly monodisperse nanocubes, to nanorods (NRs) with variable aspect ratios, and finally to long, straight nanowires (NWs). Reaction at high temperature quickly forms thermodynamically favored nanocubes, but low temperatures lead tomore » elongated particles. Transmission electron microscopy studies of reaction products at various stages of the synthesis reveal that the growth and shape-focusing of monodisperse SnTe nanocubes likely involves interparticle ripening, while directional growth of NRs and NWs may be initiated by particle dimerization via oriented attachment.« less

  16. Relic neutralino surface at a 100 TeV collider

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Bramante, Joseph; Fox, Patrick J.; Martin, Adam; Ostdiek, Bryan; Plehn, Tilman; Schell, Torben; Takeuchi, Michihisa

    2015-03-11

    We map the parameter space for minimal supersymmetric Standard Model neutralino dark matter which freezes out to the observed relic abundance, in the limit that all superpartners except the neutralinos and charginos are decoupled. In this space of relic neutralinos, we show the dominant dark matter annihilation modes, the mass splittings among the electroweakinos, direct detection rates, and collider cross sections. The mass difference between the dark matter and the next-to-lightest neutral and charged states is typically much less than electroweak gauge boson masses. With these small mass differences, the relic neutralino surface is accessible to a future 100 TeVmore » hadron collider, which can discover interneutralino mass splittings down to 1 GeV and thermal relic dark matter neutralino masses up to 1.5 TeV with a few inverse attobarns of luminosity. This coverage is a direct consequence of the increased collider energy: in the Standard Model events with missing transverse momentum in the TeV range have mostly hard electroweak radiation, distinct from the soft radiation shed in compressed electroweakino decays. As a result, we exploit this kinematic feature in final states including photons and leptons, tailored to the 100 TeV collider environment.« less

  17. Nuclear structure relevant to neutrinoless double beta decay candidate {sup 130}Te and other recent results

    SciTech Connect (OSTI)

    Kay, B. P. [Physics Division, Argonne National Laboratory, Illinois 60439 (United States)

    2013-12-30

    We have undertaken a series of single-nucleon and pair transfer reaction measurements to help constrain calculations of the nuclear matrix elements for neutrinoless double beta decay. In this talk, a short overview of measurements relevant to the {sup 130}Te?{sup 130}Xe system is given. Brief mention is made of other recent and forthcoming results.

  18. Higgs Coupling Measurements at a 1 TeV Linear Collider

    SciTech Connect (OSTI)

    Barklow, T

    2003-12-18

    Methods for extracting Higgs boson signals at a 1 TeV center-of-mass energy e{sup +}e{sup -} linear collider are described. In addition, estimates are given for the accuracy with which branching fractions can be measured for Higgs boson decays to b{bar b} WW, gg, and {gamma}{gamma}.

  19. Nanowire CdS-CdTe solar cells with molybdenum oxide as contact

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Dang, Hongmei; Singh, Vijay P.

    2015-10-06

    Using a 10 nm thick molybdenum oxide (MoO3-x) layer as a transparent and low barrier contact to p-CdTe, we demonstrate nanowire CdS-CdTe solar cells with a power conversion efficiency of 11% under front side illumination. Annealing the as-deposited MoO3 film in N2 resulted in a reduction of the cell’s series resistance, from 9.97 Ω/cm2 to 7.69 Ω/cm2, and increase in efficiency from 9.9% to 11%. Under illumination from the back, the MoO3-x/Au side, the nanowire solar cells yielded Jsc of 21 mA/cm2 and efficiency of 8.67%. Our results demonstrate use of a thin layer transition metal oxide as a potentialmore » way for a transparent back contact to nanowire CdS-CdTe solar cells. As a result, this work has implications toward enabling a novel superstrate structure nanowire CdS-CdTe solar cell on Al foil substrate by a low cost roll-to roll fabrication process.« less

  20. Relic neutralino surface at a 100 TeV collider

    SciTech Connect (OSTI)

    Bramante, Joseph; Fox, Patrick J.; Martin, Adam; Ostdiek, Bryan; Plehn, Tilman; Schell, Torben; Takeuchi, Michihisa

    2015-03-11

    We map the parameter space for minimal supersymmetric Standard Model neutralino dark matter which freezes out to the observed relic abundance, in the limit that all superpartners except the neutralinos and charginos are decoupled. In this space of relic neutralinos, we show the dominant dark matter annihilation modes, the mass splittings among the electroweakinos, direct detection rates, and collider cross sections. The mass difference between the dark matter and the next-to-lightest neutral and charged states is typically much less than electroweak gauge boson masses. With these small mass differences, the relic neutralino surface is accessible to a future 100 TeV hadron collider, which can discover interneutralino mass splittings down to 1 GeV and thermal relic dark matter neutralino masses up to 1.5 TeV with a few inverse attobarns of luminosity. This coverage is a direct consequence of the increased collider energy: in the Standard Model events with missing transverse momentum in the TeV range have mostly hard electroweak radiation, distinct from the soft radiation shed in compressed electroweakino decays. As a result, we exploit this kinematic feature in final states including photons and leptons, tailored to the 100 TeV collider environment.

  1. Nanowire CdS-CdTe solar cells with molybdenum oxide as contact

    SciTech Connect (OSTI)

    Dang, Hongmei; Singh, Vijay P.

    2015-10-06

    Using a 10 nm thick molybdenum oxide (MoO3-x) layer as a transparent and low barrier contact to p-CdTe, we demonstrate nanowire CdS-CdTe solar cells with a power conversion efficiency of 11% under front side illumination. Annealing the as-deposited MoO3 film in N2 resulted in a reduction of the cell’s series resistance, from 9.97 Ω/cm2 to 7.69 Ω/cm2, and increase in efficiency from 9.9% to 11%. Under illumination from the back, the MoO3-x/Au side, the nanowire solar cells yielded Jsc of 21 mA/cm2 and efficiency of 8.67%. Our results demonstrate use of a thin layer transition metal oxide as a potential way for a transparent back contact to nanowire CdS-CdTe solar cells. As a result, this work has implications toward enabling a novel superstrate structure nanowire CdS-CdTe solar cell on Al foil substrate by a low cost roll-to roll fabrication process.

  2. Comparison of Minority Carrier Lifetime Measurements in Superstrate and Substrate CdTe PV Devices: Preprint

    SciTech Connect (OSTI)

    Gessert, T. A.; Dhere, R. G.; Duenow, J. N.; Kuciauskas, D.; Kanevce, A.; Bergeson, J. D.

    2011-07-01

    We discuss typical and alternative procedures to analyze time-resolved photoluminescence (TRPL) measurements of minority carrier lifetime (MCL) with the hope of enhancing our understanding of how this technique may be used to better analyze CdTe photovoltaic (PV) device functionality. Historically, TRPL measurements of the fast recombination rate (t1) have provided insightful correlation with broad device functionality. However, we have more recently found that t1 does not correlate as well with smaller changes in device performance, nor does it correlate well with performance differences observed between superstrate and substrate CdTe PV devices. This study presents TRPL data for both superstrate and substrate CdTe devices where both t1 and the slower TRPL decay (t2) are analyzed. The study shows that changes in performance expected from small changes in device processing may correlate better with t2. Numerical modeling further suggests that, for devices that are expected to have similar drift field in the depletion region, effects of changes in bulk MCL and interface recombination should be more pronounced in t2. Although this technique may provide future guidance to improving CdS/CdTe device performance, it is often difficult to extract statistically precise values for t2, and therefore t2 data may demonstrate significant scatter when correlated with performance parameters.

  3. Project Reports for Te-Moak Tribe of Western Shoshone: Battle Mountain Colony- 2012 Project

    Broader source: Energy.gov [DOE]

    The Feasibility Study for the Battle Mountain Renewable Energy Park project ("Feasibility Study") will assess the feasibility, benefits, and impacts of a 5-megawatt (MW) solar photovoltaic (PV) generating system (the "Solar Project" or "Energy Park") on the Te-Moak Tribe of Western Shoshone Indians of Nevada Battle Mountain Colony in Battle Mountain, Nevada.

  4. Low-temperature photoluminescence analysis of CdTeSe crystals for radiation-detector applications

    SciTech Connect (OSTI)

    YANG G.; Roy, U. N.; Bolotnikov, A. E.; Cui, Y.; Camarda, G.S.; Hossain, A.; and James, R. B.

    2015-10-05

    Goal: Understanding the changes of material defects in CdTeSe following annealing. Experimental results and discussions: Infrared (IR) transmission microscopy; current-voltage measurements (Highlight: Improvement of resistivity of un-doped crystals after annealing); low-temperature photoluminescence (PL) spectrum of as-grown and annealed samples.

  5. Te-Moak Tribe of Western Shoshone: Battle Mountain Colony- 2012 Project

    Broader source: Energy.gov [DOE]

    The Feasibility Study for the Battle Mountain Renewable Energy Park project ("Feasibility Study") will assess the feasibility, benefits, and impacts of a 5-megawatt (MW) solar photovoltaic (PV) generating system (the "Solar Project" or "Energy Park") on the Te-Moak Tribe of Western Shoshone Indians of Nevada Battle Mountain Colony in Battle Mountain, Nevada.

  6. In-situ crystallization of GeTe\\GaSb phase change memory stacked films

    SciTech Connect (OSTI)

    Velea, A.; Borca, C. N.; Grolimund, D.; Socol, G.; Galca, A. C.; Popescu, M.; Bokhoven, J. A. van

    2014-12-21

    Single and double layer phase change memory structures based on GeTe and GaSb thin films were deposited by pulsed laser deposition (PLD). Their crystallization behavior was studied using in-situ synchrotron techniques. Electrical resistance vs. temperature investigations, using the four points probe method, showed transition temperatures of 138 °C and 198 °C for GeTe and GaSb single films, respectively. It was found that after GeTe crystallization in the stacked films, Ga atoms from the GaSb layer diffused in the vacancies of the GeTe crystalline structure. Therefore, the crystallization temperature of the Sb-rich GaSb layer is decreased by more than 30 °C. Furthermore, at 210 °C, the antimony excess from GaSb films crystallizes as a secondary phase. At higher annealing temperatures, the crystalline Sb phase increased on the expense of GaSb crystalline phase which was reduced. Extended X-ray absorption fine structure (EXAFS) measurements at the Ga and Ge K-edges revealed changes in their local atomic environments as a function of the annealing temperature. Simulations unveil a tetrahedral configuration in the amorphous state and octahedral configuration in the crystalline state for Ge atoms, while Ga is four-fold coordinated in both as-deposited and annealed samples.

  7. Investigation of deep level defects in CdTe thin films

    SciTech Connect (OSTI)

    Shankar, H.; Castaldini, A.; Dauksta, E.; Medvid, A.; Cavallini, A.

    2014-02-21

    In the past few years, a large body of work has been dedicated to CdTe thin film semiconductors, as the electronic and optical properties of CdTe nanostructures make them desirable for photovoltaic applications. The performance of semiconductor devices is greatly influenced by the deep levels. Knowledge of parameters of deep levels present in as-grown materials and the identification of their origin is the key factor in the development of photovoltaic device performance. Photo Induced Current Transient Spectroscopy technique (PICTS) has proven to be a very powerful method for the study of deep levels enabling us to identify the type of traps, their activation energy and apparent capture cross section. In the present work, we report the effect of growth parameters and LASER irradiation intensity on the photo-electric and transport properties of CdTe thin films prepared by Close-Space Sublimation method using SiC electrical heating element. CdTe thin films were grown at three different source temperatures (630, 650 and 700 C). The grown films were irradiated with Nd:YAG LASER and characterized by Photo-Induced Current Transient Spectroscopy, Photocurrent measurementand Current Voltage measurements. The defect levels are found to be significantly influenced by the growth temperature.

  8. Computational discovery of ferromagnetic semiconducting single-layer CrSnTe3

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Zhuang, Houlong L.; Xie, Yu; Kent, P. R. C.; Ganesh, P.

    2015-07-06

    Despite many single-layer materials being reported in the past decade, few of them exhibit magnetism. Here we perform first-principles calculations using accurate hybrid density functional methods (HSE06) to predict that single-layer CrSnTe3 (CST) is a ferromagnetic semiconductor, with band gaps of 0.9 and 1.2 eV for the majority and minority spin channels, respectively. We determine the Curie temperature as 170 K, significantly higher than that of single-layer CrSiTe3 (90K) and CrGeTe3 (130 K). This is due to the enhanced ionicity of the Sn-Te bond, which in turn increases the superexchange coupling between the magnetic Cr atoms. We further explore themore » mechanical and dynamical stability and strain response of this single-layer material for possible epitaxial growth. Lastly, our study provides an intuitive approach to understand and design novel single-layer magnetic semiconductors for a wide range of spintronics and energy applications.« less

  9. Measurements of the t-tbar production cross section in lepton+jets final states in pp collisions at 8TeV and ratio of 8 to 7TeV cross sections

    Office of Scientific and Technical Information (OSTI)

    2.09024v1 [hep-ex] 29 Feb 2016 EUROPEAN ORGANIZATION FOR NUCLEAR RESEARCH (CERN) CERN-EP/2016-016 2016/03/01 CMS-TOP-12-006 Measurements of the tt production cross section in lepton+jets final states in pp collisions at 8 TeV and ratio of 8 to 7 TeV cross sections The CMS Collaboration* Abstract A measurement of the top quark pair production (tt) cross section in proton-proton collisions at the centre-of-mass energy of 8 TeV is presented using data collected with the CMS detector at the LHC,

  10. Synthesis of visible light-activated TiO{sub 2} photocatalyst via surface organic modification

    SciTech Connect (OSTI)

    Jiang Dong Xu Yao Hou Bo; Wu Dong; Sun Yuhan

    2007-05-15

    A visible light-activated TiO{sub 2} photocatalyst was successfully synthesized by the surface organic modification to sol-gel-hydrothermal synthesized TiO{sub 2}. The surface hydroxyls of TiO{sub 2} nanoparticles reacted with the active -NCO groups of tolylene diisocyanate (TDI) to form a surface complex that was confirmed by the FT-IR and XPS spectra. Due to the existence of surface complex, the absorption edge of as-prepared TDI-modified TiO{sub 2} nanomaterial extended well into visible region. Compared with unmodified TiO{sub 2} and Degussa P25, the TDI-modified TiO{sub 2} photocatalysts showed higher activity for the photocatalytic degradation of methylene blue under visible light irradiation. - Graphical abstract: A visible light-activated TiO{sub 2} photocatalyst was successfully synthesized by the surface organic modification to TiO{sub 2}. The surface hydroxyls of TiO{sub 2} nanoparticles reacted with the active -NCO groups of tolylene diisocyanate (TDI) to form a surface complex. The TDI-modified TiO{sub 2} photocatalysts showed higher activity for the photocatalytic degradation of methylene blue under visible light irradiation.

  11. Structural and chemical characterization of BaTiO{sub 3} nanorods

    SciTech Connect (OSTI)

    Zagar, K.; Recnik, A.; Sturm, S.; Gajovic, A.; Ceh, M.

    2011-03-15

    Research highlights: {yields} Polycrystalline BaTiO{sub 3} nanorods were synthesized with EPD into AAO templates. {yields} Nanorods are composed of crystalline, nanosized grains with pseudo-cubic structure. {yields} Integrowth of hexagonal BaTiO{sub 3} polymorph within pseudo-cubic structure was observed. -- Abstract: An electron-microscopy investigation was performed on BaTiO{sub 3} nanorods that were processed by sol-gel electrophoretic deposition (EPD) into anodic aluminium oxide (AAO) membranes. The BaTiO{sub 3} nanorods grown within the template membranes had diameters ranging from 150 to 200 nm, with an average length of 10-50 {mu}m. By using various electron-microscopy techniques we showed that the processed BaTiO{sub 3} nanorods were homogeneous in their chemical composition. The BaTiO{sub 3} nanorods were always polycrystalline and were composed of well-crystallized, defect-free, pseudo-cubic BaTiO{sub 3} grains, ranging from 10 to 30 nm. No intergranular phases were observed between the BaTiO{sub 3} grains. A low-temperature hexagonal polymorph that is coherently intergrown with the BaTiO{sub 3} perovskite matrix was also observed as a minor phase. When annealing the AAO templates containing the BaTiO{sub 3} sol in an oxygen atmosphere the presence of the hexagonal polymorph was diminished.

  12. Ti{sub 5}O{sub 5} superstructures of cubic titanium monoxide

    SciTech Connect (OSTI)

    Gusev, A. I.

    2013-08-15

    A cubic model is proposed for the Ti{sub 5}O{sub 5} (Ti{sub 5} Black-Small-Square O{sub 5}{open_square} {identical_to} Ti{sub 90} Black-Small-Square {sub 18}O{sub 90}{open_square}{sub 18}) superstructure of nonstoichiometric titanium monoxide Ti{sub x}O{sub z} with double imperfection. The unit cell of the cubic Ti{sub 5}O{sub 5} superstructure has the threefold lattice parameter of the unit cell of the basis disordered B1 structure of Ti{sub x}O{sub z} monoxide and belongs to space group Pm 3-bar m . The channel of the disorder-order transition, i.e., Ti{sub x}O{sub z} (space group Fm 3-bar m)-Ti{sub 5}O{sub 5} (space group Pm 3-bar m), includes 75 superstructure vectors of seven stars (k{sub 10}), (k{sub 7}), (k{sub 6(1)}), (k{sub 6(2)}), (k{sub 4(1)}), (k{sub 4(2)}), and (k{sub 1}). The distribution functions of Ti and O atoms over the sites of the cubic Ti{sub 5}O{sub 5} superstructure are calculated. A comparison of the X-ray and electron diffraction data obtained for ordered TiO{sub 1.087} monoxide with the theoretical simulation results supports the existence of the cubic Ti{sub 5}O{sub 5} superstructure. The cubic (space group Pm 3-bar m) Ti{sub 5}O{sub 5} superstructure is shown to be a high-temperature structure relative to the well-known monoclinic (space group C2/m) superstructure of the same type.

  13. The Effect of Ramp Rate on the C49 to C54 Titanium Disilicide Phase Transformation from Ti and Ti(Ta)

    SciTech Connect (OSTI)

    BAILEY, GLENN A.; HU, YAO ZHI; SMITH, PAUL M.; TAY, SING PIN

    1999-09-22

    The C49 to C54 TiSi{sub 2} transformation temperature is shown to be reduced by increasing the ramp rate during rapid thermal processing and this effect is more pronounced for thinner initial Ti and Ti(Ta) films. Experiments were performed on blanket wafers and on wafers that had patterned polycrystalline Si lines with Si{sub 3}N{sub 4} sidewall spacers. Changing the ramp rate caused no change in the transformation temperature for 60 nm blanket Ti films. For blanket Ti films of 25 or 40 nm, however, increasing the ramp rate from 7 to 180 C/s decreased the transformation temperature by 15 C. Studies of patterned lines indicate that sheet resistance of narrow lines is reduced by increased ramp rates for both Ti and Ti(Ta) films, especially as the linewidths decrease below 0.4 {micro}m. This improvement is particularly pronounced for the thinnest Ti(Ta) films, which exhibited almost no linewidth effect after being annealed with a ramp rate of 75 C/s.

  14. Impact of annealing on the chemical structure and morphology of the thin-film CdTe/ZnO interface

    SciTech Connect (OSTI)

    Horsley, K. Hanks, D. A.; Weir, M. G.; Beal, R. J.; Wilks, R. G.; Blum, M.; Hming, M.; Hofmann, T.; Weinhardt, L.; and others

    2014-07-14

    To enable an understanding and optimization of the optoelectronic behavior of CdTe-ZnO nanocomposites, the morphological and chemical properties of annealed CdTe/ZnO interface structures were studied. For that purpose, CdTe layers of varying thickness (424?nm) were sputter-deposited on 100?nm-thick ZnO films on surface-oxidized Si(100) substrates. The morphological and chemical effects of annealing at 525?C were investigated using X-ray Photoelectron Spectroscopy (XPS), X-ray-excited Auger electron spectroscopy, energy dispersive X-ray spectroscopy, scanning electron microscopy, and atomic force microscopy. We find a decrease of the Cd and Te surface concentration after annealing, parallel to an increase in Zn and O signals. While the as-deposited film surfaces show small grains (100?nm diameter) of CdTe on the ZnO surface, annealing induces a significant growth of these grains and separation into islands (with diameters as large as 1??m). The compositional change at the surface is more pronounced for Cd than for Te, as evidenced using component peak fitting of the Cd and Te 3d XPS peaks. The modified Auger parameters of Cd and Te are also calculated to further elucidate the local chemical environment before and after annealing. Together, these results suggest the formation of tellurium and cadmium oxide species at the CdTe/ZnO interface upon annealing, which can create a barrier for charge carrier transport, and might allow for a deliberate modification of interface properties with suitably chosen thermal treatment parameters.

  15. Effect of neutron irradiation on defect evolution in Ti3SiC2 and Ti2AlC

    SciTech Connect (OSTI)

    Tallman, Darin J.; He, Lingfeng; Garcia-Diaz, Brenda L.; Hoffman, Elizabeth N.; Kohse, Gordon; Sindelar, Robert L.; Barsoum, Michel W.

    2015-10-23

    Here, we report on the characterization of defects formed in polycrystalline Ti3SiC2 and Ti2AlC samples exposed to neutron irradiation – up to 0.1 displacements per atom (dpa) at 350 ± 40 °C or 695 ± 25 °C, and up to 0.4 dpa at 350 ± 40 °C. Black spots are observed in both Ti3SiC2 and Ti2AlC after irradiation to both 0.1 and 0.4 dpa at 350 °C. After irradiation to 0.1 dpa at 695 °C, small basal dislocation loops, with a Burgers vector of b = 1/2 [0001] are observed in both materials. At 9 ± 3 and 10 ± 5 nm, the loop diameters in the Ti3SiC2 and Ti2AlC samples, respectively, were comparable. At 1 × 1023 loops/m3, the dislocation loop density in Ti2AlC was ≈1.5 orders of magnitude greater than in Ti3SiC2, at 3 x 1021 loops/m3. After irradiation at 350 °C, extensive microcracking was observed in Ti2AlC, but not in Ti3SiC2. The room temperature electrical resistivities increased as a function of neutron dose for all samples tested, and appear to saturate in the case of Ti3SiC2. The MAX phases are unequivocally more neutron radiation tolerant than the impurity phases TiC and Al2O3. Based on these results, Ti3SiC2 appears to be a more promising MAX phase candidate for high temperature nuclear applications than Ti2AlC.

  16. Effects of chemo-mechanical polishing on CdZnTe X-ray and gamma-ray

    Office of Scientific and Technical Information (OSTI)

    detectors (Journal Article) | SciTech Connect Effects of chemo-mechanical polishing on CdZnTe X-ray and gamma-ray detectors Citation Details In-Document Search This content will become publicly available on June 23, 2016 Title: Effects of chemo-mechanical polishing on CdZnTe X-ray and gamma-ray detectors Here, mechanically polishing cadmium zinc telluride (CdZnTe) wafers for x-ray and gamma-ray detectors often is inadequate in removing surface defects caused by cutting them from the ingots.

  17. Simulation, Modeling, and Crystal Growth of Cd0.9Zn0.1Te for Nuclear

    Office of Scientific and Technical Information (OSTI)

    Spectrometers (Journal Article) | SciTech Connect Simulation, Modeling, and Crystal Growth of Cd0.9Zn0.1Te for Nuclear Spectrometers Citation Details In-Document Search Title: Simulation, Modeling, and Crystal Growth of Cd0.9Zn0.1Te for Nuclear Spectrometers High-quality, large (10 cm long and 2.5 cm diameter), nuclear spectrometer grade Cd{sub 0.9}Zn{sub 0.1}Te (CZT) single crystals have been grown by a controlled vertical Bridgman technique using in-house zone refined precursor materials

  18. Search for contact interactions in dimuon events from pp collisions at ?s=7 TeV with the ATLAS detector

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Aad, G.; Abbott, B.; Abdallah, J.; Abdelalim, A. A.; Abdesselam, A.; Abdinov, O.; Abi, B.; Abolins, M.; Abramowicz, H.; Abreu, H.; et al

    2011-07-01

    A search for contact interactions has been performed using dimuon events recorded with the ATLAS detector in proton-proton collisions at ?s=7 TeV. The data sample corresponds to an integrated luminosity of 42 pb?. No significant deviation from the standard model is observed in the dimuon mass spectrum, allowing the following 95% C.L. limits to be set on the energy scale of contact interactions: ?>4.9 TeV (4.5 TeV) for constructive (destructive) interference in the left-left isoscalar compositeness model. These limits are the most stringent to date for ??qq contact interactions.

  19. Role of chalcogen vapor annealing in inducing bulk superconductivity in Fe1+yTe1-xSex [How does annealing in chalcogen vapor induce superconductivity in Fe1+yTe-xSex?

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Lin, Wenzhi; Ganesh, P.; Gianfrancesco, Anthony; Wang, Jun; Berlijn, Tom; Maier, Thomas A.; Kalinin, Sergei V.; Sales, Brian C.; Pan, Minghu

    2015-02-01

    Recent investigations have shown that Fe1+yTe1-xSex can be made superconducting by annealing it in Se and O vapors. The current lore is that these chalcogen vapors induce superconductivity by removing the magnetic excess Fe atoms. To investigate this phenomenon we performed a combination of magnetic susceptibility, specific heat and transport measurements together with scanning tunneling microscopy and spectroscopy and density functional theory calculations on Fe1+yTe1-xSex treated with Te vapor. We conclude that the main role of the Te vapor is to quench the magnetic moments of the excess Fe atoms by forming FeTem (m ≥ 1) complexes. We show thatmore » the remaining FeTem complexes are still damaging to the superconductivity and therefore that their removal potentially could further improve superconductive properties in these compounds.« less

  20. LaTiO₃/KTaO₃ interfaces: A new two-dimensional electron gas system

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Zou, K.; Ismail-Beigi, Sohrab; Kisslinger, Kim; Shen, Xuan; Su, Dong; Walker, F. J.; Ahn, C. H.

    2015-03-01

    We report a new 2D electron gas (2DEG) system at the interface between a Mott insulator, LaTiO₃, and a band insulator, KTaO₃. For LaTiO₃/KTaO₃ interfaces, we observe metallic conduction from 2 K to 300 K. One serious technological limitation of SrTiO₃-based conducting oxide interfaces for electronics applications is the relatively low carrier mobility (0.5-10 cm²/V s) of SrTiO₃ at room temperature. By using KTaO₃, we achieve mobilities in LaTiO₃/KTaO₃ interfaces as high as 21 cm²/V s at room temperature, over a factor of 3 higher than observed in doped bulk SrTiO₃. By density functional theory, we attribute the higher mobilitymore » in KTaO₃ 2DEGs to the smaller effective mass for electrons in KTaO₃.« less

  1. Laser cladding of Ti-6Al-4V with various carbide powders

    SciTech Connect (OSTI)

    Folkes, J.A.; Shibata, K. )

    1994-06-01

    Laser cladding Ti-6Al-4V can be achieved with various weight percentages of different carbide powders. The microstructure and morphology of the clad layer is determined by the cladding powder composition, for a given set of laser parameters, such that 10 and 20 wt% Cr[sub 3]C[sub 2] results in a [beta] + TiC clad microstructure; 10 and 20 wt% WC results in an [alpha] + TiC clad microstructure (plus some original WC); and Mo[sub 2]C gives an [alpha] + [beta] + TiC or [beta] + TiC structure, depending on the weight percentage of Mo[sub 2]C. The morphology of the TiC in all cases is dendritic or feathery, depending on the carbide content. The microstructure observed in all cases agreed well with that theoretically predicted from the energetics of carbide formation and [beta]-stabilizing properties of each element.

  2. LaTiO₃/KTaO₃ interfaces: A new two-dimensional electron gas system

    SciTech Connect (OSTI)

    Zou, K.; Ismail-Beigi, Sohrab; Kisslinger, Kim; Shen, Xuan; Su, Dong; Walker, F. J.; Ahn, C. H.

    2015-03-01

    We report a new 2D electron gas (2DEG) system at the interface between a Mott insulator, LaTiO₃, and a band insulator, KTaO₃. For LaTiO₃/KTaO₃ interfaces, we observe metallic conduction from 2 K to 300 K. One serious technological limitation of SrTiO₃-based conducting oxide interfaces for electronics applications is the relatively low carrier mobility (0.5-10 cm²/V s) of SrTiO₃ at room temperature. By using KTaO₃, we achieve mobilities in LaTiO₃/KTaO₃ interfaces as high as 21 cm²/V s at room temperature, over a factor of 3 higher than observed in doped bulk SrTiO₃. By density functional theory, we attribute the higher mobility in KTaO₃ 2DEGs to the smaller effective mass for electrons in KTaO₃.

  3. Rapidly solidified alloys and their mechanical and magnetic properties; Proceedings of the Symposium, Boston, MA, December 2-4, 1985. Volume 58

    SciTech Connect (OSTI)

    Giessen, B.C.; Polk, D.E.; Taub, A.I.

    1986-01-01

    Papers are presented on methods for processing rapidly solidified alloys, the effects of bombardment of high energy ions onto the growing surface on the structure and properties of sputtered magnetic films, and the transition from a planar interface to cellular and dendritic structures during rapid solidification processing (RSP). Consideration is given to the formation, structural relaxation and phase transformation, and chemical, magnetic, and mechanical properties of amorphous alloys. Topics discussed include crystalline magnetic materials, quasi-crystals, and the microstructures and properties of RSP Al, Ti, Mg, Ni, Fe, Co, and Cu-based alloys.

  4. Heterojunction band offsets and dipole formation at BaTiO{sub 3}/SrTiO{sub 3} interfaces

    SciTech Connect (OSTI)

    Balaz, Snjezana; Zeng, Zhaoquan; Brillson, Leonard J.; Department of Physics, The Ohio State University, 191 West Woodruff, Columbus, Ohio 43210

    2013-11-14

    We used a complement of photoemission and cathodoluminescence techniques to measure formation of the BaTiO{sub 3} (BTO) on SrTiO{sub 3} (STO) heterojunction band offset grown monolayer by monolayer by molecular beam epitaxy. X-ray photoemission spectroscopy (XPS) provided core level and valence band edge energies to monitor the valence band offset in-situ as the first few crystalline BTO monolayers formed on the STO substrate. Ultraviolet photoemission spectroscopy (UPS) measured Fermi level positions within the band gap, work functions, and ionization potentials of the growing BTO film. Depth-resolved cathodoluminescence spectroscopy measured energies and densities of interface states at the buried heterojunction. Kraut-based XPS heterojunction band offsets provided evidence for STO/BTO heterojunction linearity, i.e., commutativity and transitivity. In contrast, UPS and XPS revealed a large dipole associated either with local charge transfer or strain-induced polarization within the BTO epilayer.

  5. Effect Of The Plasma Deposition Parameters On The Properties Of Ti/TiN Multilayers For Hard Coatings Applications

    SciTech Connect (OSTI)

    Saoula, N.; Henda, K.; Kesri, R.

    2008-09-23

    In this study, we present the effect of the plasma deposition parameters on the mechanical properties of Ti/TiN multilayers. The elaboration of our films has been carried out by RF-Magnetron Sputtering (13.56 MHz) under nitrogen and argon reactive plasma at low pressure. The film depositions have been done on steel substrates. The first step of our study was the optimization of the depositions conditions in order to obtain good quality films. The amount of nitrogen in the sputtering gases being fixed at 10%. The total pressure was set between 2mTorr to 10mTorr. The deposited multilayers were characterized by X-ray diffraction (XRD), energy dispersive spectroscopy (EDS), atomic force microscopy (AFM) and micro-indentation.

  6. Anisotropic swelling and microcracking of neutron irradiated Ti3AlC2-Ti5Al2C3 materials

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Ang, Caen K.; Silva, Chinthaka M.; Shih, Chunghao Phillip; Koyanagi, Takaaki; Katoh, Yutai; Zinkle, Steven J.

    2015-12-17

    Mn + 1AXn (MAX) phase materials based on Ti–Al–C have been irradiated at 400 °C (673 K) with fission neutrons to a fluence of 2 × 1025 n/m2 (E > 0.1 MeV), corresponding to ~ 2 displacements per atom (dpa). We report preliminary results of microcracking in the Al-containing MAX phase, which contained the phases Ti3AlC2 and Ti5Al2C3. Equibiaxial ring-on-ring tests of irradiated coupons showed that samples retained 10% of pre-irradiated strength. Volumetric swelling of up to 4% was observed. Phase analysis and microscopy suggest that anisotropic lattice parameter swelling caused microcracking. Lastly, variants of titanium aluminum carbide may bemore » unsuitable materials for irradiation at light water reactor-relevant temperatures.« less

  7. Shape-memory transformations of NiTi: Minimum-energy pathways between

    Office of Scientific and Technical Information (OSTI)

    austenite, martensites, and kinetically limited intermediate states (Journal Article) | DOE PAGES Shape-memory transformations of NiTi: Minimum-energy pathways between austenite, martensites, and kinetically limited intermediate states Title: Shape-memory transformations of NiTi: Minimum-energy pathways between austenite, martensites, and kinetically limited intermediate states NiTi is the most used shape-memory alloy, nonetheless, a lack of understanding remains regarding the associated

  8. The High-Resolution Lightweight Telescope for the EUV (HiLiTE)

    SciTech Connect (OSTI)

    Martinez-Galarce, D S; Boerner, P; Soufli, R; De Pontieu, B; Katz, N; Title, A; Gullikson, E M; Robinson, J C; Baker, S L

    2008-06-02

    The High-resolution Lightweight Telescope for the EUV (HiLiTE) is a Cassegrain telescope that will be made entirely of Silicon Carbide (SiC), optical substrates and metering structure alike. Using multilayer coatings, this instrument will be tuned to operate at the 465 {angstrom} Ne VII emission line, formed in solar transition region plasma at {approx}500,000 K. HiLiTE will have an aperture of 30 cm, angular resolution of {approx}0.2 arc seconds and operate at a cadence of {approx}5 seconds or less, having a mass that is about 1/4 that of one of the 20 cm aperture telescopes on the Atmospheric Imaging Assembly (AIA) instrument aboard NASA's Solar Dynamics Observatory (SDO). This new instrument technology thus serves as a path finder to a post-AIA, Explorer-class missions.

  9. Search for Dijet Resonances in 7 TeV pp Collisions at CMS

    SciTech Connect (OSTI)

    Khachatryan, V.; et al.

    2010-11-01

    A search for narrow resonances in the dijet mass spectrum is performed using data corresponding to an integrated luminosity of 2.9 inverse pb collected by the CMS experiment at the LHC. Upper limits at the 95% confidence level (CL) are presented on the product of the resonance cross section, branching fraction into dijets, and acceptance, separately for decays into quark-quark, quark-gluon, or gluon-gluon pairs. The data exclude new particles predicted in the following models at the 95% CL: string resonances, with mass less than 2.50 TeV, excited quarks, with mass less than 1.58 TeV, and axigluons, colorons, and E_6 diquarks, in specific mass intervals. This extends previously published limits on these models.

  10. Fabrication of fluorescent composite with ultrafast aqueous synthesized high luminescent CdTe quantum dots

    SciTech Connect (OSTI)

    Zhang, Lei, E-mail: mejswu@ust.hk; Chen, Haibin, E-mail: mejswu@ust.hk, E-mail: mejswu@ust.hk; Wu, Jingshen, E-mail: mejswu@ust.hk, E-mail: mejswu@ust.hk [Department of Mechanical and Aerospace Engineering, The Hong Kong University of Science and Technology, Hong Kong and Fok Ying Tung Graduate School, The Hong Kong University of Science and Technology (Hong Kong); Bi, Xianghong, E-mail: takubatch@gmail.com [Fok Ying Tung Graduate School, The Hong Kong University of Science and Technology (Hong Kong)

    2014-05-15

    Without precursor preparation, inert gas protection and enormous amount of additives and reductants, CdTe quantum dots (QDs) can be rapidly synthesized with high quality. A 600 nm photoluminescence peak wavelength could be obtained within 1 hour's refluxing through minimal addition of 1,2-diaminoethane (DAE). The theoretical design for the experiments are illustrated and further proved by the characterization results with different concentrations and reagents. On the other hand, generation of CdTe QDs was found even under room temperature by applying droplet quantity of DAE. This indicates that QDs can be synthesized with simply a bottle and no enormous additives required. The QDs were mixed into the epoxy matrix through solution casting method with cetyltrimethylammonium (CTA) capping for phase transfer. The acquired epoxy based nanocomposite exhibits good transparency, compatibility and fluorescence.

  11. Photoluminescence studies of type-II CdSe/CdTe superlattices

    SciTech Connect (OSTI)

    Li Jingjing; Johnson, Shane R.; Wang Shumin; Ding Ding; Ning Cunzheng; Zhang Yonghang; Yin Leijun; Skromme, B. J.; Liu Xinyu; Furdyna, Jacek K.

    2012-08-06

    CdSe/CdTe type-II superlattices grown on GaSb substrates by molecular beam epitaxy are studied using time-resolved and steady-state photoluminescence (PL) spectroscopy at 10 K. The relatively long carrier lifetime of 188 ns observed in time-resolved PL measurements shows good material quality. The steady-state PL peak position exhibits a blue shift with increasing excess carrier concentration. Self-consistent solutions of the Schroedinger and Poisson equations show that this effect can be explained by band bending as a result of the spatial separation of electrons and holes, which is critical confirmation of a strong type-II band edge alignment between CdSe and CdTe.

  12. Anti pp searches for quark-gluon plasma at TeV I

    SciTech Connect (OSTI)

    Turkot, F.

    1986-06-01

    Three experiments that have been approved to run at TeV I are discussed from the viewpoint of their capability to search for evidence of the QCD phase transition in proton-antiproton collisions at 1.6 TeV. One of these experiments, E-735, was proposed as a dedicated search for quark-gluon plasma effects with a detector designed to study large total E/sub T/, low P/sub T/ individual particles. The other two, E-741 (CDF) and E-740 (DO), embody general purpose four-pi detectors designed primarily to study the physics of W and Z bosons and other large P/sub T/ phenomena. The detectors and their quark-gluon plasma signals are compared. 8 refs., 6 figs., 4 tabs. (LEW)

  13. Diffusion-Reaction Modeling of Cu Migration in CdTe Solar Devices

    SciTech Connect (OSTI)

    Guo, Da; Brinkman, Daniel; Fang, Tian; Akis, Richard; Sankin, Igor; Vasileska, Dragica; Ringhofer, Christian

    2015-09-04

    In this work, we report on development of one-dimensional (1D) finite-difference and two-dimensional (2D) finite-element diffusion-reaction simulators to investigate mechanisms behind Cu-related metastabilities observed in CdTe solar cells [1]. The evolution of CdTe solar cells performance has been studied as a function of stress time in response to the evolution of associated acceptor and donor states. To achieve such capability, the simu-lators solve reaction-diffusion equations for the defect states in time-space domain self-consistently with the free carrier transport. Re-sults of 1-D and 2-D simulations have been compared to verify the accuracy of solutions.

  14. Thermoelectric properties of polycrystalline In4Se3 and In4Te3

    SciTech Connect (OSTI)

    Shi, Xun; Cho, Jung Y; Salvador, James R.; Yang, Jihui; Wang, Hsin

    2010-01-01

    High thermoelectric performance of a single crystal layered compound In{sub 4}Se{sub 3} was reported recently. We present here an electrical and thermal transport property study over a wide temperature range for polycrystalline samples of In{sub 4}Se{sub 3} and In{sub 4}Te{sub 3}. Our data demonstrate that these materials are lightly doped semiconductors, leading to large thermopower and resistivity. Very low thermal conductivity, below 1 W/m K, is observed. The power factors for In{sub 4}Se{sub 3} and In{sub 4}Te{sub 3} are much smaller when compared with state-of-the-art thermoelectric materials. This combined with the very low thermal conductivity results in the maximum ZT value of less than 0.6 at 700 K for In{sub 4}Se{sub 3}.

  15. Higgs mass from compositeness at a multi-TeV scale

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Cheng, Hsin -Chia; Dobrescu, Bogdan A.; Gu, Jiayin

    2014-08-18

    Within composite Higgs models based on the top seesaw mechanism, we show that the Higgs field can arise as the pseudo Nambu-Goldstone boson of the broken U(3)more » $$_{L}$$ chiral symmetry associated with a vector-like quark and the t-b doublet. As a result, the lightest CP-even neutral state of the composite scalar sector is lighter than the top quark, and can be identified as the newly discovered Higgs boson. As a result, constraints on weak-isospin violation push the chiral symmetry breaking scale above a few TeV, implying that other composite scalars are probably too heavy to be probed at the LHC, but may be within reach at a future hadron collider with center-of-mass energy of about 100 TeV.« less

  16. Broadening of optical transitions in polycrystalline CdS and CdTe thin films

    SciTech Connect (OSTI)

    Li Jian; Chen Jie; Collins, R. W.

    2010-11-01

    The dielectric functions {epsilon} of polycrystalline CdS and CdTe thin films sputter deposited onto Si wafers were measured from 0.75 to 6.5 eV by in situ spectroscopic ellipsometry. Differences in {epsilon} due to processing variations are well understood using an excited carrier scattering model. For each sample, a carrier mean free path {lambda} is defined that is found to be inversely proportional to the broadening of each of the band structure critical points (CPs) deduced from {epsilon}. The rate at which broadening occurs with {lambda}{sup -1} is different for each CP, enabling a carrier group speed {upsilon}{sub g} to be identified for the CP. With the database for {upsilon}{sub g}, {epsilon} can be analyzed to evaluate the quality of materials used in CdS/CdTe photovoltaic heterojunctions.

  17. Rare-earth-rich tellurides: Gd{sub 4}NiTe{sub 2} and Er{sub 5}M{sub 2}Te{sub 2} (M=Co, Ni)

    SciTech Connect (OSTI)

    Magliocchi, Carmela; Meng, Fanqin; Hughbanks, Timothy . E-mail: trh@mail.chem.tamu.edu

    2004-11-01

    Three new rare earth metal-rich compounds, Gd{sub 4}NiTe{sub 2}, and Er{sub 5}M{sub 2}Te{sub 2} (M=Ni, Co), were synthesized in direct reactions using R, R{sub 3}M, and R{sub 2}Te{sub 3} (R=Gd, Er; M=Co, Ni) and single-crystal structures were determined. Gd{sub 4}NiTe{sub 2} is orthorhombic and crystallizes in space group Pnma with four formula units per cell. Lattice parameters at 110(2)K are a=15.548(9), b=4.113(2), c=11.7521(15)A. Er{sub 5}Ni{sub 2}Te{sub 2} and Er{sub 5}Co{sub 2}Te{sub 2} are isostructural and crystallize in the orthorhombic space group Cmcm with two formula units per cell. Lattice parameters at 110(2)K are a=3.934(1), b=14.811(4), c=14.709(4)A, and a=3.898(1), b=14.920(3), c=14.889(3)A, respectively. Metal-metal bonding correlations were analyzed using the empirical Pauling bond order concept.

  18. Thin Metal Oxide Films to Modify a Window Layer in CdTe-Based Solar Cells for Improved Performance

    SciTech Connect (OSTI)

    Lemmon, John P.; Polikarpov, Evgueni; Bennett, Wendy D.; Kovarik, Libor

    2012-05-25

    We report on CdS/CdTe photovoltaic devices that contain a thin Ta₂O₅ film deposited onto the CdS window layer by sputtering. We show that for thicknesses below 5 nm, Ta₂O₅ films between CdS and CdTe positively affect the solar cell performance, improving JSC, VOC, and the cell power conversion efficiency despite the insulating nature of the interlayer material. Using the Ta₂O₅ interlayer, a VOC gain of over 100 mV was demonstrated compared to a CdTe/CdS baseline. Application of a 1nm Ta₂O₅ interlayer enabled the fabrication of CdTe solar cells with extremely thin (less than 30 nm) CdS window layers. The efficiency of these cells exceeded that of a base line cell with 95 nm of CdS.

  19. Modeling Cu Migration in CdTe Solar Cells Under Device-Processing and Long-Term Stability Conditions: Preprint

    SciTech Connect (OSTI)

    Teeter, G.; Asher, S.

    2008-05-01

    An impurity migration model for systems with material interfaces is applied to Cu migration in CdTe solar cells. In the model, diffusion fluxes are calculated from the Cu chemical potential gradient. Inputs to the model include Cu diffusivities, solubilities, and segregation enthalpies in CdTe, CdS and contact materials. The model yields transient and equilibrium Cu distributions in CdTe devices during device processing and under field-deployed conditions. Preliminary results for Cu migration in CdTe photovoltaic devices using available diffusivity and solubility data from the literature show that Cu segregates in the CdS, a phenomenon that is commonly observed in devices after back-contact processing and/or stress conditions.

  20. Polarization of Bi{sub 2}Te{sub 3} thin film in a floating-gate capacitor structure

    SciTech Connect (OSTI)

    Yuan, Hui E-mail: qli6@gmu.edu; Li, Haitao; Zhu, Hao; Zhang, Kai; Baumgart, Helmut; Bonevich, John E.; Richter, Curt A.; Li, Qiliang E-mail: qli6@gmu.edu

    2014-12-08

    Metal-Oxide-Semiconductor (MOS) capacitors with Bi{sub 2}Te{sub 3} thin film sandwiched and embedded inside the oxide layer have been fabricated and studied. The capacitors exhibit ferroelectric-like hysteresis which is a result of the robust, reversible polarization of the Bi{sub 2}Te{sub 3} thin film while the gate voltage sweeps. The temperature-dependent capacitance measurement indicates that the activation energy is about 0.33?eV for separating the electron and hole pairs in the bulk of Bi{sub 2}Te{sub 3}, and driving them to either the top or bottom surface of the thin film. Because of the fast polarization speed, potentially excellent endurance, and the complementary metaloxidesemiconductor compatibility, the Bi{sub 2}Te{sub 3} embedded MOS structures are very interesting for memory application.