Powered by Deep Web Technologies
Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Seasonal Energy Efficiency Ratio (SEER) Investigation for Residential and Small Commercial Air-Source Heat Pumps  

Science Conference Proceedings (OSTI)

Electric utilities frequently use the seasonal energy efficiency ratio (SEER) in air conditioning–based incentive programs to categorize energy efficiency and to quantify financial value. For residential and small commercial unitary air conditioners and heat pumps, SEER is determined by the procedures outlined in ANSI/AHRI Standard 210/240. Within Standard 210/240, SEER is calculated based on laboratory test results and equations that follow specific assumptions regarding indoor temperature, ...

2012-12-21T23:59:59.000Z

2

Current Test Procedure Waivers  

Energy.gov (U.S. Department of Energy (DOE))

The U.S. Department of Energy's (DOE) regulations for covered products permit a person to seek a waiver, or an interim waiver, from the test procedure requirements for covered appliances and...

3

Rough Ride Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

NTP005 NTP005 Revision 2 Effective December 1, 2004 Electric Vehicle Rough Road Course Test Prepared by Electric Transportation Applications Prepared by: _______________________________ Date:__________ Ryan Harkins Approved by: _________________________________________________ Date: _______________ Donald B. Karner ©2004 Electric Transportation Applications All Rights Reserved Procedure ETA-NTP005 Revision 2 2 TABLE OF CONTENTS 1.0 Objectives 3 2.0 Purpose 3 3.0 Documentation 3 4.0 Initial Conditions and Prerequisites 4 5.0 Testing Activity Requirements 6 6.0 Glossary 12 7.0 References 14 Appendices Appendix A - Electric Vehicle Rough Road Test Data Sheet 15

4

Optimum Statistical Test Procedure  

E-Print Network (OSTI)

In this paper we obtain a test which minimizes the sum of the two error probabilities irrespective of whether $\\sigma^2$ is known or unknown.

Rajesh Singh; Jayant Singh; Florentin Smarandache

2009-04-10T23:59:59.000Z

5

MITG test procedure and results  

DOE Green Energy (OSTI)

Elements and modules for Radioisotope Thermoelectric Generator have been performance tested since the inception of the RTG program. These test articles seldom resembled flight hardware and often lacked adequate diagnostic instrumentation. Because of this, performance problems were not identified in the early stage of program development. The lack of test data in an unexpected area often hampered the development of a problem solution. A procedure for conducting the MITG Test was developed in an effort to obtain data in a systematic, unambiguous manner. This procedure required the development of extensive data acquisition software and test automation. The development of a facility to implement the test procedure, the facility hardware and software requirements, and the results of the MITG testing are the subject of this paper.

Eck, M.B.; Mukunda, M.

1983-01-01T23:59:59.000Z

6

EV America Skid Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

6 6 Revision 2 Effective October 1, 2007 Braking Test Prepared by Electric Transportation Applications Prepared by: _______________________________ Date: _________ Roberta Brayer Approved by: _________________________________________________ Date: _______________ Donald Karner Procedure ETA-HTP06 Revision 2 i TABLE OF CONTENTS 1. Objectives 1 2. Purpose 1 3. Documentation 1 4. Initial Conditions and Prerequisites 1 5. Testing Activity Requirements 3 5.3 Dry Controlled Test 4 6. Glossary 5 7. References 7 Appendices Appendix A - Handling Pad Test Data Sheet 8

7

Building Technologies Office: Current Test Procedure Waivers  

NLE Websites -- All DOE Office Websites (Extended Search)

Test Procedure Test Procedure Waivers to someone by E-mail Share Building Technologies Office: Current Test Procedure Waivers on Facebook Tweet about Building Technologies Office: Current Test Procedure Waivers on Twitter Bookmark Building Technologies Office: Current Test Procedure Waivers on Google Bookmark Building Technologies Office: Current Test Procedure Waivers on Delicious Rank Building Technologies Office: Current Test Procedure Waivers on Digg Find More places to share Building Technologies Office: Current Test Procedure Waivers on AddThis.com... About Standards & Test Procedures Implementation, Certification & Enforcement Rulemakings & Notices Current Rulemakings & Notices Test Procedure Waivers Recent Federal Register Notices How to Participate or Comment

8

Inspection system performance test procedure  

SciTech Connect

This procedure establishes requirements to administer a performance demonstration test. The test is to demonstrate that the double-shell tank inspection system (DSTIS) supplied by the contractor performs in accordance with the WHC-S-4108, Double-Shell Tank Ultrasonic Inspection Performance Specification, Rev. 2-A, January, 1995. The inspection system is intended to provide ultrasonic (UT) and visual data to determine integrity of the Westinghouse Hanford Company (WHC) site underground waste tanks. The robotic inspection system consists of the following major sub-systems (modules) and components: Mobile control center; Deployment module; Cable management assembly; Robot mechanism; Ultrasonic testing system; Visual testing system; Pneumatic system; Electrical system; and Control system.

Jensen, C.E.

1995-01-17T23:59:59.000Z

9

EV America Skid Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

4 4 Revision 1 Effective June 2008 Electromagnetic Interference and Susceptibility Test Prepared by Electric Transportation Applications Prepared by: _______________________________ Date:__________ Garrett P. Beauregard Approved by: ______________________________________________ Date: _______________ Donald B. Karner Procedure ETA-GTP004 Revision 1 2 Table of Contents 1 Objective ..................................................................................................................... 3 2 Purpose........................................................................................................................ 3 3 Documentation............................................................................................................

10

EV America Skid Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

3 3 Revision 1 Effective June 2008 Battery Capacity and Depth of Discharge Test Prepared by Electric Transportation Applications Prepared by: _______________________________ Date:__________ Garrett P. Beauregard Approved by: ______________________________________________ Date: _______________ Donald B. Karner Procedure ETA-GTP003 Revision 1 2 Table of Contents 1 Objective ..................................................................................................................... 3 2 Purpose........................................................................................................................ 3 3 Documentation............................................................................................................

11

EV America Skid Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

2 2 Revision 1 Effective June 2008 Traction System Test Prepared by Electric Transportation Applications Prepared by: _______________________________ Date:__________ Garrett P. Beauregard Approved by: ______________________________________________ Date: _______________ Donald B. Karner Procedure ETA-GTP002 Revision 1 2 Table of Contents 1 Objective ..................................................................................................................... 3 2 Purpose........................................................................................................................ 3 3 Documentation............................................................................................................

12

Building Technologies Office: Standards and Test Procedures  

NLE Websites -- All DOE Office Websites (Extended Search)

Standards and Test Standards and Test Procedures to someone by E-mail Share Building Technologies Office: Standards and Test Procedures on Facebook Tweet about Building Technologies Office: Standards and Test Procedures on Twitter Bookmark Building Technologies Office: Standards and Test Procedures on Google Bookmark Building Technologies Office: Standards and Test Procedures on Delicious Rank Building Technologies Office: Standards and Test Procedures on Digg Find More places to share Building Technologies Office: Standards and Test Procedures on AddThis.com... About Standards & Test Procedures Implementation, Certification & Enforcement Rulemakings & Notices Further Guidance ENERGY STAR® Popular Links Success Stories Previous Next Lighten Energy Loads with System Design. Learn More.

13

Building Technologies Office: Test Procedure Development and...  

NLE Websites -- All DOE Office Websites (Extended Search)

Test Procedure Development and Revision to someone by E-mail Share Building Technologies Office: Test Procedure Development and Revision on Facebook Tweet about Building...

14

Building Technologies Office: Test Procedure Waivers  

NLE Websites -- All DOE Office Websites (Extended Search)

Waivers on Twitter Bookmark Building Technologies Office: Test Procedure Waivers on Google Bookmark Building Technologies Office: Test Procedure Waivers on Delicious Rank...

15

Test Procedure Waivers | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Appliance & Equipment Standards » Rulemakings & Notices » Test Appliance & Equipment Standards » Rulemakings & Notices » Test Procedure Waivers Test Procedure Waivers Products covered by standards change as manufacturers add new features to their products and update designs in order to compete for consumers. Innovation and product development occasionally causes products to change in ways that either (1) make the results of a test procedure unrepresentative of actual energy use or efficiency, or (2) make it impossible to test in accordance with the relevant test procedure. For this reason, the Department of Energy (DOE) considers petitions for waivers from test procedures under certain circumstances. In general, any interested party-typically a manufacturer-may submit a petition for a test procedure waiver for a basic model of a covered product

16

A general design for energy test procedures  

SciTech Connect

Appliances are increasingly controlled by microprocessors. Unfortunately, energy test procedures have not been modified to capture the positive and negative contributions of the microprocessor to the appliance's energy use. A new test procedure is described which captures both the mechanical and logical features present in many new appliances. We developed an energy test procedure for refrigerators that incorporates most aspects of the proposed new approach. Some of the strengths and weaknesses of the new test are described.

Meier, Alan

2000-06-15T23:59:59.000Z

17

Building Technologies Office: Current Test Procedure Waivers  

NLE Websites -- All DOE Office Websites (Extended Search)

Test Procedure Waivers Test Procedure Waivers The U.S. Department of Energy's (DOE) regulations for covered products permit a person to seek a waiver, or an interim waiver, from the test procedure requirements for covered appliances and commercial equipment if certain criteria are satisfied. Regulations applicable to test procedure waivers for appliances can be found at 10 CFR 430.27; those applicable to test procedure waivers for commercial equipment are at 10 CFR 431.401. This table lists all waivers to test procedures that DOE has granted and that are still in effect. The links to the notices provide access to the dockets in Regulations.gov, which contain all notices and public comments. For more information, please email: AS_Waiver_Requests@ee.doe.gov The links to the notices provides access to the docket in regulations.gov, which contains all notices and public comments.

18

EV America Skid Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

6 Revision 3 Effective February 1, 2008 Braking Test Prepared by Electric Transportation Applications Prepared by: Date: Derek Peterson...

19

Standards and Test Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Standards and Test Procedures Standards and Test Procedures Standards and Test Procedures The Department of Energy (DOE) establishes energy efficiency standards for certain appliances and equipment, and currently covers more than 50 different products. Authority to undertake this effort was granted by Congress, and DOE follows a four phase process when reviewing existing and developing new standards. Each Product page provides information on recent updates, current standards and test procedures, waivers, exceptions, and exemptions, statutory authority, and historical information. For information on current Rulemakings, visit Current Rulemaking and Notices. Consumer Products Battery Chargers and External Power Supplies Ceiling Fans Central Air Conditioners and Heat Pumps Clothes Dryers

20

Building Technologies Office: Standards and Test Procedures  

NLE Websites -- All DOE Office Websites (Extended Search)

icon Public Meetings & Comment Deadlines Newsletter Recent Federal Register Notices Standards and Test Procedures The Department of Energy (DOE) establishes energy efficiency...

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Void fraction instrument acceptance test procedure  

DOE Green Energy (OSTI)

This acceptance test procedure (ATP) was written to test the void fraction instrument (VFI) and verify that the unit is ready for field service. The procedure verifies that the mechanical and electrical features (not specifically addressed in the software ATP) and software alarms are operating as designed.

Pearce, K.L.

1994-09-15T23:59:59.000Z

22

Nitrogen chiller acceptance test procedure  

SciTech Connect

This document includes the inspection and testing requirements for the Nitrogen Chiller unit. The Chiller will support the Rotary Mode core Sampling System during the summer. The Chiller cools the Nitrogen Purge Gas that is used when drilling in tank wastes to cool the drill bit.

Kostelnik, A.J.

1995-03-07T23:59:59.000Z

23

Workshop on Test Procedures for Materials for Hydrogen ...  

Science Conference Proceedings (OSTI)

Test Procedures for Hydrogen Pipelines. ... The NIST Workshop on Materials Test Procedures for Hydrogen Pipelines Proceedings is now available. ...

24

AZ-101 Mixer Pump Test Qualification Test Procedures (QTP)  

SciTech Connect

Describes the Qualification test procedure for the AZ-101 Mixer Pump Data Acquisition System (DAS). The purpose of this Qualification Test Procedure (QTP) is to confirm that the AZ-101 Mixer Pump System has been properly programmed and hardware configured correctly. This QTP will test the software setpoints for the alarms and also check the wiring configuration from the SIMcart to the HMI. An Acceptance Test Procedure (ATP), similar to this QTP will be performed to test field devices and connections from the field.

THOMAS, W.K.

2000-01-10T23:59:59.000Z

25

Biomonitoring test procedures and biological criteria  

SciTech Connect

The Water Environment Federation recently issued a special publication, Biomonitoring in the Water Environment. In this paper, the authors highlight the contents of the chapter 3, Biomonitoring Test Procedures, identify current trends in test procedures and introduce the concept of biological criteria (biocriteria). The book chapter (and this paper) focuses on freshwater and marine chronic and acute toxicity tests used in the National Pollutant Discharge Elimination System (NPDES) permits program to identify effluents and receiving waters containing toxic materials in acutely or chronically toxic concentrations. The two major categories of toxicity tests include acute tests and chronic tests. The USEPA chronic tests required in NPDEs permits have been shortened to 7 days by focusing on the most sensitive life-cycle stages; these tests are often referred to as short-term chronic tests. The type of test(s) required depend on NPDES permit requirements, objectives of the test, available resources, requirements of the test organisms, and effluent characteristics such as variability in flow or toxicity. The permit writer will determine the requirements for toxicity test(s) by considering such factors as dilution, effluent variability, and exposure variability. Whether the required test is acute or chronic, the objective of the test is to estimate the safe or no effect concentration which is defined as the concentration which will permit normal propagation of fish and other aquatic life in the receiving waters. In this paper, the authors review the types of toxicity tests, the commonly used test organisms, and the uses of toxicity test data. In addition, they briefly describe research on new methods and the use of biological criteria.

Kszos, L.A. [Oak Ridge National Lab., TN (United States); Lipschultz, M.J. [City of Las Vegas, NV (United States); Foster, W.E. [Saint Mary`s Coll., Winona, MN (United States)

1997-10-01T23:59:59.000Z

26

Building Technologies Office: ENERGY STAR Test Procedures and...  

NLE Websites -- All DOE Office Websites (Extended Search)

Test Procedures and Verification to someone by E-mail Share Building Technologies Office: ENERGY STAR Test Procedures and Verification on Facebook Tweet about Building Technologies...

27

Meeting Concerning Potential Test Procedures and Energy Conservation...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Concerning Potential Test Procedures and Energy Conservation Standards for Set-Top Boxes and Network Equipment Meeting Concerning Potential Test Procedures and Energy Conservation...

28

Residential photovoltaic power conditioner subsystem test procedures  

DOE Green Energy (OSTI)

The inspections to be made, the conditions for measurement, the variables to be measured and the analyses to be performed in order to characterize the operation of a power-conditioning subsystem (PCS) are described. Of primary concern is the small, utility-interactive PCS in the 2- to 10-kW power range for use in a residential photovoltaic (PV) system feeding a single-phase 120/240-volt line. The procedure is broken down into four main tasks: analysis of the design, tests under nominal conditions, tests under extreme conditions, and accelerated environmental stress tests. The results of these tests will provide an objective assessment of PCS performance under the full range of conditions likely to be encountered in actual applications.

Cox, III, C. H.

1982-02-01T23:59:59.000Z

29

Test Procedure Development and Revision | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Test Procedure Development and Revision Test Procedure Development and Revision Test Procedure Development and Revision Most energy conservation standards rulemakings are accompanied by a concurrent test procedure rulemaking. Test procedures detail the protocols that manufacturers must follow when testing their products for compliance with Department of Energy (DOE) standards. DOE also uses the test procedures to determine compliance with the applicable standards in any verification or enforcement testing. The procedures specify how to measure and calculate the energy efficiency and/or energy use of each appliance. Test procedures also specify how to calculate an estimate of an appliance's annual operating cost, which is used on the EnergyGuide label as required by the Federal Trade Commission.

30

Alternative Fuels Data Center: Fuel Economy Test Procedures and Labeling  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Fuel Economy Test Fuel Economy Test Procedures and Labeling to someone by E-mail Share Alternative Fuels Data Center: Fuel Economy Test Procedures and Labeling on Facebook Tweet about Alternative Fuels Data Center: Fuel Economy Test Procedures and Labeling on Twitter Bookmark Alternative Fuels Data Center: Fuel Economy Test Procedures and Labeling on Google Bookmark Alternative Fuels Data Center: Fuel Economy Test Procedures and Labeling on Delicious Rank Alternative Fuels Data Center: Fuel Economy Test Procedures and Labeling on Digg Find More places to share Alternative Fuels Data Center: Fuel Economy Test Procedures and Labeling on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type Fuel Economy Test Procedures and Labeling

31

WRAP Trupact Loading System Operational Test Procedure  

Science Conference Proceedings (OSTI)

This procedure has been prepared to verify the TRUPACT System (TS) operates in accordance with system design and specifications.

DOSRAMOS, E.V.

1999-09-01T23:59:59.000Z

32

Alternative Fuels Data Center: Biodiesel Quality Testing Procedures  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Biodiesel Quality Biodiesel Quality Testing Procedures to someone by E-mail Share Alternative Fuels Data Center: Biodiesel Quality Testing Procedures on Facebook Tweet about Alternative Fuels Data Center: Biodiesel Quality Testing Procedures on Twitter Bookmark Alternative Fuels Data Center: Biodiesel Quality Testing Procedures on Google Bookmark Alternative Fuels Data Center: Biodiesel Quality Testing Procedures on Delicious Rank Alternative Fuels Data Center: Biodiesel Quality Testing Procedures on Digg Find More places to share Alternative Fuels Data Center: Biodiesel Quality Testing Procedures on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type Biodiesel Quality Testing Procedures Each biodiesel or other renewable diesel producer, distributor, or importer

33

Common Information Model Meter Disconnect/Reconnect Interoperability Test Procedure  

Science Conference Proceedings (OSTI)

The Common Information Model (CIM) Disconnect/Reconnect Interoperability Test Procedure is one in a series of EPRI Interoperability Test Procedures (ETIPs) created by EPRI whose purpose is to thoroughly document the actors, interfaces, and test steps for the interoperability testing of specific parts of the International Electrotechnical Commission (IEC) Common Information Model (CIM) standard. The Test Procedures are initially being used for EPRI demonstration tests and are intended, over time, to form ...

2011-12-21T23:59:59.000Z

34

Common Information Model Meter Outage Nominal Interoperability Test Procedure  

Science Conference Proceedings (OSTI)

The CIM Meter Outage Nominal Interoperability Test Procedure is one in a series of EPRI CIM Interoperability Test Procedures (ETIPs) created by EPRI whose purpose is to thoroughly document the actors, interfaces, and test steps for the interoperability testing of specific parts of the International Electrotechnical Commission (IEC) Common Information Model (CIM) standard. The Test Procedures are initially being used for EPRI demonstration tests and are intended, over time, to form the basis of a set of C...

2011-12-16T23:59:59.000Z

35

Common Information Model On Demand Meter Read Interoperability Test Procedure  

Science Conference Proceedings (OSTI)

The Common Information Model (CIM) On Demand Meter Read Interoperability Test Procedure is one in a series of EPRI Interoperability Test Procedures (ETIPs) created by EPRI whose purpose is to thoroughly document the actors, interfaces, and test steps for the interoperability testing of specific parts of the International Electrotechnical Commission (IEC) Common Information Model (CIM) standard. The Test Procedures are initially being used for EPRI demonstration tests and are intended, over time, to form ...

2011-12-14T23:59:59.000Z

36

Common Information Model Meter Tamper Detection Interoperability Test Procedure  

Science Conference Proceedings (OSTI)

The Common Information Model (CIM) Meter Tamper Detection Interoperability Test Procedure is one in a series of EPRI Interoperability Test Procedures (ETIPs) created by EPRI whose purpose is to thoroughly document the actors, interfaces, and test steps for the interoperability testing of specific parts of the International Electrotechnical Commission (IEC) Common Information Model (CIM) standard. The Test Procedures are initially being used for EPRI demonstration tests and are intended, over time, to for...

2011-11-30T23:59:59.000Z

37

MIT validation probe acceptance test procedure  

SciTech Connect

As part of the Multi-Functional Instrument Trees (MITs) a Validation Probe is being fabricated by Los Alamos National Laboratories (LANL). The Validation Probe assembly is equipped with a Winch, depth counter, and a Resistance Temperature Detector (RTD) which will render a means for verifying the temperature readings of which will render a means for verifying the temperature readings of the MIT thermocouples. The purpose of this Acceptance Test Procedure (ATP) is to provide verification that the Validation Probe functions properly and accordingly to LANL design and specification. This ATP will be used for all Validation Probes procured from LANL. The ATP consists of a receiving inspection, RTD ambient temperature; RTD electrical failure, RTD insulation resistance, and accurate depth counter operation inspections. The Validation Probe is composed of an intank probe, a cable and winching system, and a riser extension (probe guide) which bolts onto the MIT. The validation`s thermal sensor is an RTD that is housed in a 0.062 inch diameter, magnesium oxide fill, 316 stainless steel tube. The sheath configuration provides a means for spring loading the sensor firmly against the validation tube`s inner wall. A 45 pound cylindrical body is connected above the sheath and is used as a force to lower the probe into the tank. This cylindrical body also provides the means to interconnect both electrically and mechanically to the winch system which lowers the probe to a specified location within the validation tube located in the tank.

Escamilla, S.A.

1994-08-23T23:59:59.000Z

38

702AZ aging waste ventilation facility year 2000 test procedure  

SciTech Connect

This test procedure was developed to determine if the 702AZ Tank Ventilation Facility system is Year 2000 Compliant. The procedure provides detailed instructions for performing the operations necessary and documenting the results. This verification procedure will document that the 702AZ Facility Systems are year 2000 compliant and will correctly meet the criteria established in this procedure.

Winkelman, W.D.

1998-07-22T23:59:59.000Z

39

DOE Issues Final Appliance Test Procedure Rule | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Appliance Test Procedure Rule Appliance Test Procedure Rule DOE Issues Final Appliance Test Procedure Rule December 8, 2006 - 9:46am Addthis WASHINGTON, DC - The U.S. Department of Energy (DOE) today announced a final rule establishing new test procedures and related definitions to determine the energy efficiency of certain residential appliances and commercial equipment. The rulemaking clarifies and codifies the test procedures mandated by the Energy Policy Act (EPAct) of 2005. "These new test procedures are the foundation for standards that will help bring more energy efficient options to the marketplace and result in energy savings for all Americans," said DOE Assistant Secretary for Energy Efficiency and Renewable Energy Andy Karsner. The final rulemaking, which appears in today's Federal Register, will

40

DOE Launches Public Test Procedure Guidance Website | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Launches Public Test Procedure Guidance Website Launches Public Test Procedure Guidance Website DOE Launches Public Test Procedure Guidance Website July 22, 2010 - 4:14pm Addthis The Department of Energy this week launched a new online database offering guidance on the Department's test procedures for appliances and commercial equipment. The new database will provide a publicly accessible forum for anyone with questions about -- or needing clarification of -- DOE's test procedures. This new online resource will also ensure that all manufacturers and members of the public are equally and immediately aware of the Department's interpretations of its test procedures. The database is available here. The database -- which is searchable by product category -- is designed to enable manufacturers, trade associations, and all other interested members

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

DOE Launches Public Test Procedure Guidance Website | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Public Test Procedure Guidance Website Public Test Procedure Guidance Website DOE Launches Public Test Procedure Guidance Website July 22, 2010 - 4:14pm Addthis The Department of Energy this week launched a new online database offering guidance on the Department's test procedures for appliances and commercial equipment. The new database will provide a publicly accessible forum for anyone with questions about -- or needing clarification of -- DOE's test procedures. This new online resource will also ensure that all manufacturers and members of the public are equally and immediately aware of the Department's interpretations of its test procedures. The database is available here. The database -- which is searchable by product category -- is designed to enable manufacturers, trade associations, and all other interested members

42

NFRC Test Procedure for Measuring the Steady-State  

E-Print Network (OSTI)

NFRC Test Procedure for Measuring the Steady-State Thermal Transmittance of Fenestration Systems Adopted: March 15, 1991 Revised: April 17, 1997 Prepared by: Test Laboratory Task Group U Test Procedure for Measuring the Steady-State Thermal Transmittance of Fenestration Systems Adopted

Massachusetts at Amherst, University of

43

Light duty utility arm equipment qualification test procedure  

SciTech Connect

The Equipment Qualification Test described in this test procedure document is the acceptance test procedure (ATP) for the LDUA Baseline System. It verifies that the equipment is complete and in working order, and demonstrates its readiness for being deployed into an actual underground storage tank.

Kiebel, G.R., Westinghouse Hanford

1996-07-22T23:59:59.000Z

44

PNNL:About PNNL:SEER Awards  

NLE Websites -- All DOE Office Websites (Extended Search)

Staff Awards and Honors Staff Awards and Honors Science and Engineering External Recognition (SEER) Program SEER logo The SEER Program establishes a proactive, organized approach for nominating PNNL scientists and engineers for individual awards and recognition in major scientific and technical venues. Honors include fellowships, major professional society awards, government awards such as the PECASE and E.O. Lawrence, National Academy honors, and many others. Helping our researchers earn prestigious awards and honors not only supports their professional development, it enhances the reputation of PNNL, and ultimately, supports the Laboratory's business objectives. External Recognition Opportunity Calendar The SEER Program offers a formal, centralized process for recognitions and

45

Test Procedures for Faucets, Showerheads, Water Closets, Urinals...  

NLE Websites -- All DOE Office Websites (Extended Search)

Certain Commercial and Industrial Equipment: Test Procedures for Showerheads, Faucets, Water Closets, Urinals, and Commercial Prerinse Spray Valves AGENCY: Office of Energy...

46

Comparison of Test Procedures and Energy Efficiency Criteria...  

NLE Websites -- All DOE Office Websites (Extended Search)

International Standards & Labeling Programs for Copy Machines, External Power Supplies, LED Displays, Residential Gas Cooktops and Televisions Title Comparison of Test Procedures...

47

Test Procedure for §170.302 (p) Emergency Access  

Science Conference Proceedings (OSTI)

... September 24, 2010 1 Test Procedure for §170.302 (p) Emergency Access ... 170.302(p) Emergency Access. Permit authorized users ...

2013-11-06T23:59:59.000Z

48

Additional Guidance Regarding Application of Current Procedures for Testing  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Additional Guidance Regarding Application of Current Procedures for Additional Guidance Regarding Application of Current Procedures for Testing Energy Consumption of Clothes Washers with Warm Rinse Cycles, Issued: June 30, 2010 Additional Guidance Regarding Application of Current Procedures for Testing Energy Consumption of Clothes Washers with Warm Rinse Cycles, Issued: June 30, 2010 Additional Guidance Regarding Application of Current Procedures for Testing Energy Consumption of Clothes Washers with Warm Rinse Cycles, Issued: June 30, 2010. Draft of DOE interpretive rule, which sets out DOE's views on the clothes washer testing procedure described in 10 CFR § 430 Appendix J1, having to do with how to apply the testing procedures to washers with a warm rinse option. This draft interpretive rule represents DOE's interpretation of

49

ENERGY STAR Test Procedures and Verification | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

ENERGY STAR » ENERGY STAR Test ENERGY STAR » ENERGY STAR Test Procedures and Verification ENERGY STAR Test Procedures and Verification The Department of Energy (DOE) is the lead agency in the development and revision of all test procedures for products in the ENERGY STAR® program, including those products that are also subject to DOE's Energy Conservation Standards program. As specifications are updated and new products or metrics are added to the ENERGY STAR program, DOE is responsible for developing and revising methods, responding to stakeholder comments, and answering any testing-related questions that arise as a result of the procedures being utilized. To simplify the process for interested parties, more information on the test procedure development for ENERGY STAR products can be found on each of

50

Rocky Flats ash test procedure (sludge stabilization)  

SciTech Connect

Rocky Flats Ash items have been identified as the next set of materials to be stabilized. This test is being run to determine charge sizes and soak times to completely stabilize the Rocky Flats Ash items. The information gathered will be used to generate the heating rampup cycle for stabilization. This test will also gain information on the effects of the glovebox atmosphere (moisture) on the stabilized material. This document provides instructions for testing Rocky Flats Ash in the HC-21C muffle furnace process.

Winstead, M.L.

1995-09-14T23:59:59.000Z

51

Test procedure forms for sludge retrieval and packaging  

SciTech Connect

This document provides test procedure forms for sludge retrieval and packaging tests in the 305 Cold Test Facility. The completed and approved forms provide all descriptions, criteria and analysis to safely perform sludge equipment tests in the 305 Cold Test Facility.

Feigenbutz, L.V.

1994-09-27T23:59:59.000Z

52

US advanced battery consortium in-vehicle battery testing procedure  

DOE Green Energy (OSTI)

This article describes test procedures to be used as part of a program to monitor the performance of batteries used in electric vehicle applications. The data will be collected as part of an electric vehicle testing program, which will include battery packs from a number of different suppliers. Most data will be collected by on-board systems or from driver logs. The paper describes the test procedure to be implemented for batteries being used in this testing.

NONE

1997-03-01T23:59:59.000Z

53

Acceptance test procedure: RMW Land Disposal Facility Project W-025  

SciTech Connect

This ATP establishes field testing procedures to demonstrate that the electrical/instrumentation system functions as intended by design for the Radioactive Mixed Waste Land Disposal Facility. Procedures are outlined for the field testing of the following: electrical heat trace system; transducers and meter/controllers; pumps; leachate storage tank; and building power and lighting.

Roscha, V. [Westinghouse Hanford Co., Richland, WA (United States)

1994-12-12T23:59:59.000Z

54

NERVA Program. Operating procedure: cart cooling system, Test Cell A  

SciTech Connect

The instructions described in this procedure are typical of the operation of Test Cell A relative to the KIWI-B4A. Operation of Test Cell A relative to the NRX reactor will require modifications dictated by specific test requirements. Under NRX conditions, it will be the responsibility of the test cell manager to evaluate the capabilities of Test Cell A in terms of given test requirements and then set forth detailed checklists which will be compatible with the test requirements.

1963-09-01T23:59:59.000Z

55

Approved Test Procedures Version 1.1 Release Notes  

E-Print Network (OSTI)

Approved Test Procedures Version 1.1 Release Notes 1 Change Reason for Change 302.a drugdrug, drug allergy In the Informative Test Description section Added clarification to the example. 302.c Problem List In the Informative Test Description section Added the sentence "The test also

56

NBSBR 84-2867 Test Procedures for Rating  

E-Print Network (OSTI)

NBSBR 84-2867 Test Procedures for Rating Residential Heating and Cooling Absorption Equipment U HEATING AND COOLING ABSORPTION EQUIPMENT Brian Weber Reinhard Radermacher David Didion U.S. DEPARTMENT-fired absorption devices operating in either the heating or cooling modes. These procedures are designed to include

Oak Ridge National Laboratory

57

USABC electric vehicle Battery Test Procedures Manual. Revision 2  

DOE Green Energy (OSTI)

This manual summarizes the procedural information needed to perform the battery testing being sponsored by the United States Advanced Battery Consortium (USABC). This information provides the structure and standards to be used by all testing organizations, including the USABC developers, national laboratories, or other relevant test facilities.

NONE

1996-01-01T23:59:59.000Z

58

DOE Seeks Comment on Application of Clothes Washer Test Procedure |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Application of Clothes Washer Test Procedure Application of Clothes Washer Test Procedure DOE Seeks Comment on Application of Clothes Washer Test Procedure June 30, 2010 - 3:02pm Addthis Today, the U.S. Department of Energy (DOE) issued a draft interpretative rule clarifying its views on the application of the current residential clothes washer test procedure to machines that offer a warm rinse option that is not included in the recommended cycle for washing cotton or linen clothes. The Department is soliciting feedback from the public on the draft interpretive rule, which is available here, until July 30, 2010. Addthis Related Articles Save Energy and More with ENERGY STAR. ENERGY STAR clothes washers use 50% less energy to wash clothes than standard washing machines. Tips: Laundry DOE Solicits Views on the Implementation of Large-Capacity Clothes Washer

59

DOE Seeks Comment on Application of Clothes Washer Test Procedure |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Seeks Comment on Application of Clothes Washer Test Procedure Seeks Comment on Application of Clothes Washer Test Procedure DOE Seeks Comment on Application of Clothes Washer Test Procedure June 30, 2010 - 3:02pm Addthis Today, the U.S. Department of Energy (DOE) issued a draft interpretative rule clarifying its views on the application of the current residential clothes washer test procedure to machines that offer a warm rinse option that is not included in the recommended cycle for washing cotton or linen clothes. The Department is soliciting feedback from the public on the draft interpretive rule, which is available here, until July 30, 2010. Addthis Related Articles DOE Seeks Comment on Definition of Showerhead Save Energy and More with ENERGY STAR. ENERGY STAR clothes washers use 50% less energy to wash clothes than standard washing machines.

60

Flammable gas interlock spoolpiece flow response test plan and procedure  

DOE Green Energy (OSTI)

The purpose of this test plan and procedure is to test the Whittaker electrochemical cell and the Sierra Monitor Corp. flammable gas monitors in a simulated field flow configuration. The sensors are used on the Rotary Mode Core Sampling (RMCS) Flammable Gas Interlock (FGI), to detect flammable gases, including hydrogen and teminate the core sampling activity at a predetermined concentration level.

Schneider, T.C., Fluor Daniel Hanford

1997-02-13T23:59:59.000Z

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

International Comparison of Energy Efficiency Criteria and Test Procedures  

NLE Websites -- All DOE Office Websites (Extended Search)

International Comparison of Energy Efficiency Criteria and Test Procedures International Comparison of Energy Efficiency Criteria and Test Procedures in Standards and Labeling Programs for Computer Monitors and Commercial Gas Stoves Title International Comparison of Energy Efficiency Criteria and Test Procedures in Standards and Labeling Programs for Computer Monitors and Commercial Gas Stoves Publication Type Report LBNL Report Number LBNL-6506E Year of Publication 2013 Authors Khanna, Nina, Nan Zhou, David Fridley, and John Romankiewicz Date Published 12/2013 Publisher Lawrence Berkeley National Laboratory Keywords Standards and labeling Abstract This report presents a technical review and comparative analysis of existing and/or proposed international mandatory energy performance standards, and voluntary and mandatory energy efficiency labels and test procedures for two products - computer monitors and commercial gas stoves - being considered for revised and new minimum energy performance standards (MEPS) in China. An overview of the scope of international programs, energy efficiency and other energy-related requirements, description and detailed summary table of criteria and procedures in major test standards are presented. In addition, an estimation of potential energy savings if China were to adopt revised MEPS comparable to international levels is provided for computer monitors. A proposed methodology for estimating potential energy savings based on the European Union experience is provided for commercial gas stoves in the absence of available sales or energy consumption data.

62

Operability test procedure [Tank] 241-SY-101 equipment removal system  

DOE Green Energy (OSTI)

The 241-SY-101 equipment removal system (ERS) consists of components, equipment, instrumentation and procedures that will provide the means to disconnect, retrieve, contain, load and transport the Mitigation Pump Assembly (MPA) from waste Tank 241-SY-101 to the Central Waste Complex (CWC). The Operability Test Procedure (OTP) will test the interfaces between ERS components and will rehearse the procedure for MPA removal and transportation to the extent they can be mocked-up at the CTF (Cold Test Facility). At the conclusion of the OTP, the ERS components and equipment will be removed from the CTF, entered into the Component Based Recall System (CBRS), and stored until needed for actual MPA removal and transportation.

Mast, J.C.

1994-12-08T23:59:59.000Z

63

PUREX (SAMCONS) uninterruptible power supply (UPS) acceptance test procedure  

SciTech Connect

This Acceptance Test Procedure for the PUREX Surveillance and Monitoring and Control System (SAMCONS) Uninterruptible Power Supply (UPS) provides for testing and verifying the proper operation of the control panel alarms and trouble functions, the 6roper functioning of the AC inverter, ability of the battery supply to maintain the SAMCONS load for a minimum of two hours , and proper interaction with the SAMCONS Video graphic displays for alarm displays.

Blackaby, W.B.

1997-09-01T23:59:59.000Z

64

241-AZ-101 Mixer Pump Demonstration Test Gamma Cart Acceptance Test Procedure and Quality Test Plan (ATP and QTP)  

Science Conference Proceedings (OSTI)

Shop Test of the Gamma Cart System to be used in the AZ-101 Mixer Pump Demonstration Test. Tests hardware and software. This procedure involves testing the Instrumentation involved with the Gamma Cart System, local and remote, including: depth indicators, speed controls, interface to data acquisition software and the raising and lowering functions. This Procedure will be performed twice, once for each Gamma Cart System. This procedure does not test the accuracy of the data acquisition software.

WHITE, D.A.

2000-03-01T23:59:59.000Z

65

241-AZ-101 Mixer Pump Demonstration Test Gamma Cart Acceptance Test Procedure and Quality Test Plan (ATP and QTP)  

SciTech Connect

Shop test of the sludge mobilization cart system to be used in the AZ-101 Mixer Pump Demonstration Test Tests hardware and software. This procedure involves testing the Instrumentation involved with the Gamma Cart System, local and remote, including depth indicators, speed controls, interface to data acquisition software and the raising and lowering functions. This Procedure will be performed twice, once for each Gamma Cart System. This procedure does not test the accuracy of the data acquisition software.

WHITE, D.A.

2000-01-27T23:59:59.000Z

66

Acceptance test report for the AN valve pit leak detection and low point drain assembly mock up test procedure  

SciTech Connect

This document describes The Performance Mock-up Test Procedure for the Valve Pit Leak Detection and Low Point Drain Assembly Performance Mock-Up Test Procedure.

EWER, K.L.

1999-07-20T23:59:59.000Z

67

Residential Clothes Washers Test Procedure Notice of Proposed Rulemaking  

NLE Websites -- All DOE Office Websites (Extended Search)

19:12 Sep 20, 2010 19:12 Sep 20, 2010 Jkt 220001 PO 00000 Frm 00001 Fmt 4717 Sfmt 4717 E:\FR\FM\21SEP2.SGM 21SEP2 srobinson on DSKHWCL6B1PROD with PROPOSALS2 Tuesday, September 21, 2010 Part II Department of Energy 10 CFR Part 430 Energy Conservation Program for Consumer Products: Test Procedure for Residential Clothes Washers; Proposed Rule VerDate Mar2010 19:12 Sep 20, 2010 Jkt 220001 PO 00000 Frm 00002 Fmt 4701 Sfmt 4702 E:\FR\FM\21SEP2.SGM 21SEP2 srobinson on DSKHWCL6B1PROD with PROPOSALS2 57556 Federal Register / Vol. 75, No. 182 / Tuesday, September 21, 2010 / Proposed Rules DEPARTMENT OF ENERGY 10 CFR Part 430 [Docket No. EERE-2010-BT-TP-0021] RIN 1904-AC08 Energy Conservation Program for Consumer Products: Test Procedure for Residential Clothes Washers AGENCY: Office of Energy Efficiency and

68

Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid N  

Science Conference Proceedings (OSTI)

This is a Test Report for Acceptance Test Procedure (ATP) RPP-5489. This test report provides the results of the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''N''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document.

KOCH, M.R.

2000-02-03T23:59:59.000Z

69

Lightning arrestor connector lead magnesium niobate qualification pellet test procedures.  

SciTech Connect

Enhanced knowledge preservation for DOE DP technical component activities has recently received much attention. As part of this recent knowledge preservation effort, improved documentation of the sample preparation and electrical testing procedures for lead magnesium niobate--lead titanate (PMN/PT) qualification pellets was completed. The qualification pellets are fabricated from the same parent powders used to produce PMN/PT lightning arrestor connector (LAC) granules at HWF&T. In our report, the procedures for fired pellet surface preparation, electrode deposition, electrical testing and data recording are described. The dielectric measurements described in our report are an information only test. Technical reasons for selecting the electrode material, electrode size and geometry are presented. The electrical testing is based on measuring the dielectric constant and dissipation factor of the pellet during cooling from 280 C to 220 C. The most important data are the temperature for which the peak dielectric constant occurs (Curie Point temperature) and the peak dielectric constant magnitude. We determined that the peak dielectric constant for our procedure would be that measured at 1 kHz at the Curie Point. Both the peak dielectric constant and the Curie point parameters provide semi-quantitative information concerning the chemical and microstructural homogeneity of the parent material used for the production of PMN/PT granules for LACs. Finally, we have proposed flag limits for the dielectric data for the pellets. Specifically, if the temperature of the peak dielectric constant falls outside the range of 250 C {+-} 30 C we propose that a flag limit be imposed that will initiate communication between production agency and design agency personnel. If the peak dielectric constant measured falls outside the range 25,000 {+-} 10,000 we also propose that a flag limit be imposed.

Tuohig, W. (Honeywell FM& T, Kansas City, MO); Mahoney, Patrick A.; Tuttle, Bruce Andrew; Wheeler, Jill Susanne

2009-02-01T23:59:59.000Z

70

Test Procedure for 170.302.h Incorporate Laboratory Test Results APPROVED Version 1.1 September 24, 2010  

E-Print Network (OSTI)

Test Procedure for §170.302.h Incorporate Laboratory Test Results APPROVED Version 1.1 September 24, 2010 1 Test Procedure for §170.302 (h) Incorporate Laboratory Test Results This document describes the test procedure for evaluating conformance of complete EHRs or EHR modules1

71

Acceptance test procedure for SY Tank Farm replacement exhauster unit  

SciTech Connect

The proper functioning of a new 241-SY Tank Farm replacement exhauster will be acceptance tested, to establish operability and to provide an operational baseline for the equipment. During this test, a verification of all of the alarm and control circuits associated with the exhaust, which provide operating controls and/or signals to local and remote alarm/annunciator panels, shall be performed. Test signals for sensors that provide alarms, warnings, and/or interlocks will be applied to verify that alarm, warning, and interlock setpoints are correct. Alarm and warning lights, controls, and local and remote readouts for the exhauster will be verified to be adequate for proper operation of the exhauster. Testing per this procedure shall be conducted in two phases. The first phase of testing, to verify alarm, warning, and interlock setpoints primarily, will be performed in the MO-566 Fab Shop. The second phase of testing, to verify proper operation and acceptable interface with other tank farm systems, will be conducted after the exhauster and all associated support and monitoring equipment have been installed in the SY Tank Farm. The exhauster, which is mounted on a skid and which will eventually be located in the SY tank farm, receives input signals from a variety of sensors mounted on the skid and associated equipment. These sensors provide information such as: exhauster system inlet vacuum pressure; prefilter and HEPA filter differential pressures; exhaust stack sampler status; exhaust fan status; system status (running/shut down); and radiation monitoring systems status. The output of these sensors is transmitted to the exhauster annunciator panel where the signals are displayed and monitored for out-of-specification conditions.

Becken, G.W.

1994-12-16T23:59:59.000Z

72

Definitions common to all certification and test procedures are in: D-200 Definitions for Certification Procedures and Test Procedures for Vapor Recovery Systems  

E-Print Network (OSTI)

For the purpose of this procedure, the term "ARB " refers to the State of California Air Resources Board, and the term "ARB Executive Officer " refers to the Executive Officer of the ARB or his or her authorized representative or designate. 1.1 General Applicability This procedure applies to the determination of the one minute static pressure performance of a vapor recovery system of a cargo tank by fluid mechanical principles. This procedure applies to any vapor emissions associated with the dispensing of any fluid, although it is written to reflect application to the hydrocarbon vapors associated with the dispensing of gasoline. 1.2 Determinations of Compliance and Violation Determinations of certain modes of compliance with and violation of certification specifications is outlined in § 9. 1.3 Modifications Modification of this procedure may be necessary for vapors and fluids other than the hydrocarbon vapors associated with the dispensing of gasoline. Any modification of this method shall be subject to approval by the ARB Executive Officer. 2 PRINCIPLE AND SUMMARY OF TEST PROCEDURE Upon completion of loading operations at the bulk gasoline distribution facility, the gasoline cargo tank is pressurized, with nitrogen, to 18 inches water column. By using the total cargo California Air Resources Board March 17, 1999 TP-204.2, Page 1tank shell capacity, post-loading headspace volume, and the Ideal Gas Law, a one-minute maximum allowable pressure decay is calculated. The pressure decay is monitored for one minute and compliance is determined by comparison with the maximum allowable calculated value. The leak rate through the cargo tank internal vapor vent valve is similarly obtained. 3

unknown authors

1996-01-01T23:59:59.000Z

73

Federal Test Procedure Emissions Test Results from Ethanol Variable-Fuel Vehicle Chevrolet Luminas  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Federal Test Procedure Emissions Test Results from Federal Test Procedure Emissions Test Results from Ethanol Variable-Fuel Vehicle Chevrolet Luminas Kenneth J. Kelly, Brent K. Bailey, and Timothy C. Coburn National Renewable Energy Laboratory Wendy Clark Automotive Testing Laboratories, Inc. Peter Lissiuk Environmental Research and Development Corp. Presented at Society for Automotive Engineers International Spring Fuels and Lubricants Meeting Dearborn, MI May 6-8, 1996 The work described here was wholly funded by the U.S. Department of Energy, a U.S. government agency. As such, this information is in the public domain, may be copied and otherwise accessed freely, and is not subject to copyright laws. These papers were previously published in hard copy form by the Society of Automotive Engineers, Inc. (Telephone: 412.776.4970; E-mail: publications@sae.org)

74

Test plan/procedure for the SPM-1 shipping container system. Revision 0  

SciTech Connect

The 49 CFR 173.465 Type A packaging tests will verify that SPM-1 will provide adequate protection and pass as a Type A package. Test will determine that the handle of the Pig will not penetrate through the plywood spacer and rupture the shipping container. Test plan/procedure provides planning, pre-test, setup, testing, and post-testing guidelines and procedures for conducting the {open_quotes}Free Drop Test{close_quotes} procedure for the SPM-1 package.

Flanagan, B.D.

1995-07-01T23:59:59.000Z

75

Sandia National Laboratories Electrochemical Storage System Abuse Test Procedure Manual  

DOE Green Energy (OSTI)

The series of tests described in this report are intended to simulate actual use and abuse conditions and internally initiated failures that may be experienced in electrochemical storage systems (ECSS). These tests were derived from Failure Mode and Effect Analysis, user input, and historical abuse testing. The tests are to provide a common framework for various ECSS technologies. The primary purpose of testing is to gather response information to external/internal inputs. Some tests and/or measurements may not be required for some ECSS technologies and designs if it is demonstrated that a test is not applicable, and the measurements yield no useful information.

Unkelhaeuser, Terry; Smallwood David

1999-07-01T23:59:59.000Z

76

Adams disassembly procedure for Bldg. 10, Nevada Test Site  

SciTech Connect

The disassembly of the `Adams` primary was scheduled for April 28, 29, and 30, 1959. The method of disassembly is provided as a procedure to be accomplished in order and the time and initials of the person accomplishing each step recorded.

Beckman, K. F.

1959-04-24T23:59:59.000Z

77

How to Make Appliance Standards Work: Improving Energy and Water Efficiency Test Procedures  

E-Print Network (OSTI)

test procedures for appliances. ” Energy and BuildingsEnergy Efficiency In Domestic Appliances And Lighting 4thLBNL # How to Make Appliance Standards Work: Improving

Lutz, Jim

2012-01-01T23:59:59.000Z

78

An evaluation of predictive environmental test procedures for sewage sludge.  

E-Print Network (OSTI)

??This research project aimed at evaluating four internationally accepted leachate extraction tests to determine their applicability on sewage sludge samples. Furthermore, the present analytical method… (more)

Kasselman, Graeme

2005-01-01T23:59:59.000Z

79

Thermal test procedure for a paraboloid concentrator solar cooker  

SciTech Connect

Suitable thermal tests have been identified for performance evaluation of a concentrating solar cooker. These tests provide parameters that characterize the performance of the solar cooker, and are more or less independent of the climatic variables. The overall heat loss factor is obtained from the cooling curve and the optical efficiency factor is determined from the heating curve - both under full load conditions. The performance characteristic curve for the solar cooker is obtained and discussed. The study indicates that the no load test, which is useful in the case of a box type solar cooker, is not appropriate in the case of concentrator type cookers.

Mullick, S.C.; Kandpal, T.C.; Kumar, S. (Indian Institute of Technology, New Delhi (India))

1991-01-01T23:59:59.000Z

80

Testing a Procedure for Automatic Classification of Hydrometeor Types  

Science Conference Proceedings (OSTI)

Examples of automatic interpretation of polarimetric measurements made with an algorithm that classifies precipitation, from an Oklahoma squall line and a Florida airmass storm are presented. Developed in this paper are sensitivity tests of this ...

Dus?an S. Zrni?; Alexander Ryzhkov; Jerry Straka; Yidi Liu; J. Vivekanandan

2001-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Acceptance test procedure MICON software exhaust fan control modifications  

Science Conference Proceedings (OSTI)

This acceptance test verifies the MICON program changes for the new automatic transfer switch ATS-2 alarms, the Closed Loop Cooling isolator status, the CB-3 position alarm, and the alarms for the new emergency fan damper backup air compressor.

SILVAN, G.R.

1999-05-21T23:59:59.000Z

82

A class of matrices to test inversion procedures  

Science Conference Proceedings (OSTI)

The test matrices given by M. L. Pei [Comm. ACM 5, 10 (Oct. 1962), 508] and R. D. Rodman [Comm. ACM 6, 9 (Sept. 1963, 515] are special cases of a general class of matrices with complex elements for which an explicit ...

Randall E. Cline

1964-12-01T23:59:59.000Z

83

Gas characterization system 241-AN-105 field acceptance test procedure  

DOE Green Energy (OSTI)

This document details the field Acceptance Testing of a gas characterization system being installed on waste tank 241-AN-105. The gas characterization systems will be used to monitor the vapor spaces of waste tanks known to contain measurable concentrations of flammable gases.

Schneider, T.C.

1996-03-01T23:59:59.000Z

84

Gas characterization system 241-AW-101 field acceptance test procedure  

DOE Green Energy (OSTI)

This document details the field Acceptance Testing of a gas characterization system being installed on waste tank 241-AW-101. The gas characterization systems will be used to monitor the vapor spaces of waste tanks known to contain measurable concentrations of flammable gases.

Schneider, T.C.

1996-03-01T23:59:59.000Z

85

Qualification test procedures and results for Honeywell solar collector subsystem, single-family residence  

DOE Green Energy (OSTI)

The test procedures and results are described in qualifying the Honeywell solar collector subsystem. Testing began in mid-August 1976, and was concluded in late February 1977. Testing was done in the following areas: pressure, service loads, hail, solar degradation, pollutants, thermal degradation, and outgassing. Results from these tests are summarized.

Not Available

1977-02-01T23:59:59.000Z

86

Building Energy Simulation Test for Existing Homes (BESTEST-EX): Instructions for Implementing the Test Procedure, Calibration Test Reference Results, and Example Acceptance-Range Criteria  

Science Conference Proceedings (OSTI)

This publication summarizes building energy simulation test for existing homes (BESTEST-EX): instructions for implementing the test procedure, calibration tests reference results, and example acceptance-range criteria.

Judkoff, R.; Polly, B.; Bianchi, M.; Neymark, J.; Kennedy, M.

2011-08-01T23:59:59.000Z

87

Developing a standardized test procedure for hybrid vehicles: The challenge of the SAE HEV task force  

DOE Green Energy (OSTI)

In 1992, the Society of Automotive Engineers (SAE) established a task force to develop a procedure for measuring electric energy consumption, all-electric range, fuel economy, and exhaust emissions for hybrid vehicles; the procedure will be submitted to regulatory agencies as representing the automotive industry`s recommendations. The draft procedure is currently being tested on hybrid vehicles. The University of Maryland`s parallel hybrid was tested in September 1994, and the University of California-Davis` parallel hybrid and the University of Illinois` series hybrid will be tested in November 1994 and January 1995, respectively. The procedure is being modified to incorporate any lessons learned, and the task force hopes to recommend the final procedure to the SAE by mid 1995.

Penney, T; Christensen, D [National Renewable Energy Lab., Golden, CO (United States); Poulos, S [General Motors Corp., Warren, MI (United States)

1994-11-01T23:59:59.000Z

88

Novel Battery Testing Procedures and Analytical Methodologies for Hybrid Electric Vehicles  

SciTech Connect

The Idaho National Engineering and Environmental Laboratory has developed novel testing procedures and analytical methodologies to assess the performance of batteries for use in hybrid electric vehicles. Tests include both characterization and cycle life and/or calendar life. Tests have been designed for both Power Assist and Dual Mode applications. Analytical procedures include a battery scaling methodology, the calculation of pulse resistance, pulse power, available energy, and differential capacitance, and the modeling of calendar and cycle life data. At periodic intervals during life testing, a series of Reference Performance Tests are executed to determine changes in the baseline performance of the batteries.

Motloch, Chester George; Batt, J. R.; Christophersen, Jon Petter; Wright, Randy Ben; Hunt, Gary Lynn

2001-06-01T23:59:59.000Z

89

Supervisory Control and Data Acquisition System (SCADA) Substation C3-3 Acceptance Test Procedure  

Science Conference Proceedings (OSTI)

The purpose of this acceptance test procedure (ATP) is to demonstrate that the newly installed Supervisory Control and Data Acquisition (SCADA) computer system functions as intended by the design.

ZAKRAJSEK, M.F.

2000-10-17T23:59:59.000Z

90

Supervisory Control and Data Acquisition System (SCADA) Substation C3S4 Acceptance Test Procedure  

Science Conference Proceedings (OSTI)

The purpose of this acceptance test procedure (ATP) is to demonstrate that the newly installed Supervisory Control and Data Acquisition (SCADA) computer system functions as intended by the design.

ZAKRAJSEK, M.F.

2000-10-17T23:59:59.000Z

91

Solid-State Lighting: IESNA LM-80-08 - An Overview of the Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

IESNA LM-80-08 - An Overview IESNA LM-80-08 - An Overview of the Test Procedure and How it is Used for ENERGY STAR® to someone by E-mail Share Solid-State Lighting: IESNA LM-80-08 - An Overview of the Test Procedure and How it is Used for ENERGY STAR® on Facebook Tweet about Solid-State Lighting: IESNA LM-80-08 - An Overview of the Test Procedure and How it is Used for ENERGY STAR® on Twitter Bookmark Solid-State Lighting: IESNA LM-80-08 - An Overview of the Test Procedure and How it is Used for ENERGY STAR® on Google Bookmark Solid-State Lighting: IESNA LM-80-08 - An Overview of the Test Procedure and How it is Used for ENERGY STAR® on Delicious Rank Solid-State Lighting: IESNA LM-80-08 - An Overview of the Test Procedure and How it is Used for ENERGY STAR® on Digg Find More places to share Solid-State Lighting: IESNA LM-80-08 -

92

Interim test methods and procedures for determining the performance of small photovoltaic systems  

DOE Green Energy (OSTI)

This document provides test methods and procedures for determining the performance of small stand-alone and utility-grid connected PV systems. The procedures in this document provide a common approach for evaluating whether a given PV system is suitable to perform the function it was designed and manufactured to accomplish and meet the application load. This test document fills a testing void and provides the catalyst and focus for establishing the technical foundation and bridging the institutional barriers needed to reduce uncertainty that a system`s performance will be what its designers and builders claim. The need for this document was recently made more apparent with the initiation of a PV Global Approval Program (PVGAP) at the international level and is in response to concerns that PV systems being fielded must meet performance standards and that these standards include system-level performance type tests. The title of these test procedures is prefaced with the word interim because experience in using the procedures is needed before a consensus standard is developed and accepted by the PV community through its activities with the IEEE Standards Coordinating Committee 21 (SCC21) and International Electrotechnical Commission Technical Committee 82 (IEC TC82) national and international standards-making bodies. Both entities have initiated projects to develop test standards and will need the technical basis and validation of test procedures such as those presented in this document before a consensus is achieved by the PV community.

McNutt, P.; Kroposki, B.; Hansen, R.; DeBlasio, R.

1998-07-01T23:59:59.000Z

93

Using virtual reality and mood-induction procedures to test products with consumers of ceramic tiles  

Science Conference Proceedings (OSTI)

This work describes a Virtual Reality Environment (VRE), through which users are able to view and test ceramic tile products. Users' virtual interfacing with the products generated emotional experiences that allowed them to feel ''engaged'' with the ... Keywords: Consumers, Mood-induction procedures, Product testing, Relaxation, Sense of presence, Virtual reality

Berenice Serrano; Cristina Botella; Rosa M. BañOs; Mariano AlcañIz

2013-05-01T23:59:59.000Z

94

Round-robin testing of Soleq EV cort according to the SAE J1634 test procedure dated May 1993  

DOE Green Energy (OSTI)

The Society of Automotive Engineers Recommended Practice, SAE J1634, {open_quotes}Electric Vehicle Energy Consumption and Range Test Procedure{close_quotes}, May 1993, describes a standard method of determining the range and energy consumption for electric vehicles. Consequent to the U.S. Department of Energy`s (DOE) rulemaking released on February 4, 1994, the EPA is currently considering factoring electric vehicles into the Corporate Average Fuel Economy (CAFE) calculations using the SAE J1634 procedure. The purpose of this project is to provide information regarding the suitability of this recommended practice for determining the energy economy value to be factored into the CAFE. Issues leading to possible inconsistent results (such as the repeatability of the procedure, thoroughness of the procedure`s methods, and variance between different laboratories using different dynamometers) need to be resolved prior to passing legislation which will mandate use of this test in determining the electric vehicle CAFE credit. To this end, separate tests were performed on a Soleq EVcort vehicle by the INEL, the EPA, Ford Motor Company, Southwest Research Institute, and the California Air Resources Board using their own facilities and personnel. Acceptable departures from the driving profile prescribed by SAEJ1634 are not well defined. This deficiency in the procedure is even more noticeable due to the EVcort`s marginal acceleration performance.

Cole, G.H.

1993-05-01T23:59:59.000Z

95

Development of an Outdoor Concentrating Photovoltaic Module Testbed, Module Handling and Testing Procedures, and Initial Energy Production Results  

DOE Green Energy (OSTI)

This report addresses the various aspects of setting up a CPV testbed and procedures for handling and testing CPV modules.

Muller, M.

2009-09-01T23:59:59.000Z

96

Energy Efficiency Program for Certain Commercial and Industrial Equipment: Test Procedures for  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6/2/11 6/2/11 Comments to the following DOE Proposed Rules: 10 CFR Part 431 [Docket No. EERE-2010-BT-TP-0036] RIN 1904-AC38 Energy Efficiency Program for Certain Commercial and Industrial Equipment: Test Procedures for Automatic Commercial Ice Makers Submitted by: Mary C. Howe, President, Howe Corporation, Chicago, IL 60642 mchowe@howecorp.com CORPORATION 1650 N Elston Ave * Chicago, IL. 60642 * (773) 235-0200 * Fax (773) 235-0269 * E-mail: howeinfo@howecorp.com 2 Item 1 - DOE also requests comment on the proposal that the use of amended test procedure be required upon the effective date of any test procedure final rule, 30 days after publication in the Federal Register. In the case of the addition of continuous production remote condenser ACIM's, the outside testing

97

Test procedures and instructions for single shell tank saltcake cesium removal with crystalline silicotitanate  

SciTech Connect

This document provides specific test procedures and instructions to implement the test plan for the preparation and conduct of a cesium removal test, using Hanford Single Shell Tank Saltcake from tanks 24 t -BY- I 10, 24 1 -U- 108, 24 1 -U- 109, 24 1 -A- I 0 1, and 24 t - S-102, in a bench-scale column. The cesium sorbent to be tested is crystalline siticotitanate. The test plan for which this provides instructions is WHC-SD-RE-TP-024, Hanford Single Shell Tank Saltcake Cesium Removal Test Plan.

Duncan, J.B.

1997-01-07T23:59:59.000Z

98

Information Resources: IESNA LM-80-08 - An Overview of the Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

IESNA LM-80-08 - An Overview of the Test Procedure and How it is Used for ENERGY STAR® IESNA LM-80-08 - An Overview of the Test Procedure and How it is Used for ENERGY STAR® This October 30, 2008 webcast provided an overview of LM-80-08, Approved Method for Measuring Lumen Maintenance of LED Light Sources, and how DOE's ENERGY STAR program for Solid-State Lighting (SSL) Luminaires will use LM-80 to estimate lifetime for qualified SSL Luminaires. Richard Karney, U.S. Department of Energy, began the webcast with the announcement that LM-80-08 is now available through IESNA. The test procedure can be purchased online through the IES store at https://www.ies.org/store/. Kevin Dowling, Chairman, Testing Procedures SSL Committee, presented on the specifics of the LM-80 test procedure and the changes reflected in the final version. Jeff McCullough, Pacific Northwest National Laboratory, went through an overview of how the results of LM-80 are used for the DOE ENERGY STAR SSL program.

99

Interim Test Procedures for Evaluating Electrical Performance and Grid Integration of Vehicle-to-Grid Applications  

NLE Websites -- All DOE Office Websites (Extended Search)

Interim Test Procedures for Interim Test Procedures for Evaluating Electrical Performance and Grid Integration of Vehicle-to-Grid Applications S. Chakraborty, W. Kramer, B. Kroposki, G. Martin, P. McNutt, M. Kuss, T. Markel, and A. Hoke Technical Report NREL/TP-5500-51001 June 2011 NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency & Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. National Renewable Energy Laboratory 1617 Cole Boulevard Golden, Colorado 80401 303-275-3000 * www.nrel.gov Contract No. DE-AC36-08GO28308 Interim Test Procedures for Evaluating Electrical Performance and Grid Integration of Vehicle-to-Grid Applications S. Chakraborty, W. Kramer, B. Kroposki, G. Martin, P. McNutt, M. Kuss, T. Markel,

100

A Functional Test Procedure for the improved commissioning of a VAV system  

E-Print Network (OSTI)

In the context of the IEA40 research project, a specification of a “Functional Test Procedure” was progressively developed using the CA-MET building in Namur as real size test bench for the application and validation of the procedure. The target system is a typical VAV system devoted to the ventilation, cooling and air conditioning functions. The procedure consists in a series of operations to be applied to the system, considered as a set of connected components and taking into account the following constraints: 1) time availability 2) intrinsic limitations of the system 3) reference performances. The proposed procedure is divided in two sets of actions: 1) a number of preliminary actions allowing to take the best benefit of the subsequent phases: a) identification of available measurement points b) identification of actuators characteristics c) identification of control strategies d) aeraulic network calculations e) selection of measurement techniques and experimental design 2) the verification tasks themselves: The philosophy of the verification process is to bring the system into a number of states which allowed each specific check to be carried out. The organisation of the procedure tries to optimize the time spent for commissioning by logically sequencing the operations according to the following order: 1) test in manual (ie not controlled by the BEMS) operation 2) test in manual (ie not controlled by the BEMS) stop 3) test in normal operation 4) test at maximum flowrate 5) test at minimum flowrate 6) test in automatic stop The paper will provide the specific operations to be carried out at each step and will illustrate the whole process with the prototyping work performed on the CA-MET building in Namur.

Andre, P.; Lacote, P.; Aparecida Silva, C.; Hannay, J.; Lebrun, J.

2004-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

PNGV Battery Testing Procedures and Analytical Methodologies for Hybrid Electric Vehicles  

SciTech Connect

Novel testing procedures and analytical methodologies to assess the performance of hybrid electric vehicle batteries have been developed. Tests include both characterization and cycle life and/or calendar life, and have been designed for both Power Assist and Dual Mode applications. Analytical procedures include a battery scaling methodology, the calculation of pulse resistance, pulse power, available energy, and differential capacity, and the modeling of calendar and cycle life data. Representative performance data and examples of the application of the analytical methodologies including resistance growth, power fade, and cycle and calendar life modeling for hybrid electric vehicle batteries are presented.

Motloch, Chester George; Belt, Jeffrey R; Christophersen, Jon Petter; Wright, Randy Ben; Hunt, Gary Lynn; Haskind, H. J.; Tartamella, T.; Sutula, R.

2002-06-01T23:59:59.000Z

102

DOE response to questions from AHAM on the supplemental proposed test procedure  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

response to questions from AHAM on the supplemental proposed test procedure for response to questions from AHAM on the supplemental proposed test procedure for residential clothes washers"? (1) What exactly does the language in Part B mean and what is the intent? * The intent of Part B is to use the methodology that AHAM had suggested specifically for extra-hot cycles, but to make it more broadly applicable to any temperature combination that is locked out of the Normal cycle. * The proposed Part (B) language is meant to be consistent with GE's original suggestion in response to the NOPR. (GE, No. 15 at pp. 1-2) * When testing cycles under Part (B), manufacturers would only need to test the temperature combination that is locked out of the Normal cycle.

103

Interim qualification tests and procedures for terrestrial photovoltaic thin-film flat-plate modules  

DOE Green Energy (OSTI)

This document provides recommended procedures and specifications for qualification tests that are structured to evaluate terrestrial thin-film flat-plate photovoltaic nonconcentrating modules intended for power generation applications. The qualification tests provided in this document are designed to evaluate flat-plate thin-film photovoltaic (PV) module design performance and susceptibility to known failure mechanisms. Emphasis is placed on testing and evaluating module performance characteristics and design features that will affect possible degradation of module performance and physical properties resulting from solar exposure, environmental weathering, mechanical loading, corrosion, and module shadowing. Because of limited thin-film module field operation experience and the evolutionary nature of new thin-film module material technologies and designs, these tests should not be considered definitive or complete, nor do they provide a basis to predict 30-year field life. Current understanding of failure and degradation mechanisms and the relationship between accelerated tests and field reliability is not sufficient to allow accurate estimation of life-expectancy, nor are the cycling tests given in this document considered to be equivalent to a full 30-year field exposure. However, the test and evaluation procedures given in this document provide a common approach for conducting qualification tests. Acceptable results from these tests should provide reasonable assurance that the modules that pass these tests will perform reliably in the field but for an unspecified period of time. 8 refs., 6 figs.

DeBlasio, R.; Mrig, L.; Waddington, D.

1990-01-01T23:59:59.000Z

104

Evaluation of fine-particle size catalysts using standard test procedures  

SciTech Connect

The goal of this project is to evaluate and compare the activities/selectivities of fine-particle size catalysts being developed in the DOE/PETC Advanced Research (AR) Liquefaction Program by using standard coal liquefaction activity test procedures. Since bituminous and subbituminous coals have significantly different properties, it is feasible that catalysts may perform differently with these coal types. Because all previous testing has been done with the DECS-17 Blind Canyon bituminous coal, it is important to develop the capability of evaluating catalysts using a subbituminous coal. Initial efforts towards developing a subbituminous coal test are aimed at comparing the reactivities of the Wyodak subbituminous coal and the Blind Canyon bituminous coal. Therefore, the same factorial experimental design was used with the Wyodak coal as was used previously with the Blind Canyon coal. In addition, PNL`s 6-line ferrihydrite catalyst precursor was used in the development of the Wyodak coal test procedure because this catalyst is the best powder catalyst found to date in Sandia`s tests with Blind Canyon coal. Results show that Blind Canyon coal yields higher DHP amounts in the reaction products and higher tetrahydrofuran conversions at the higher severity conditions. Wyodak coal gives higher heptane conversions and higher gas yields for all conditions tested.

Stohl, F.V.; Diegert, K.V.; Goodnow, D.C.

1996-07-01T23:59:59.000Z

105

MEMORANDUM TO: File FROM: David R. Hill RE: Meeting Concerning Potential Test Procedures and Energy Conservation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

MEMORANDUM MEMORANDUM TO: File FROM: David R. Hill RE: Meeting Concerning Potential Test Procedures and Energy Conservation Standards for Set-Top Boxes and Network Equipment DATE: March 14, 2012 In compliance with the Department of Energy's guidance on ex parte communications (74 Fed. Reg. 52795 (Oct. 14, 2009)), this memorandum provides a summary of a March 7, 2012, meeting with DOE officials concerning potential test procedures and energy conservation standards for set-top boxes and network equipment. Meeting attendees: John Cymbalski (DOE - EE) Jeremy Dommu (DOE - EE) Ashley Armstrong (DOE - EE) Dan Cohen (DOE - GC) Celia Sher (DOE - GC) Cecilia Martaus (AT&T) Mike Pfau (AT&T) Jeff Dygert (AT&T) David Hill (Sidley Austin) The AT&T representatives discussed a number of concerns with DOE's potential promulgation

106

Sampling and Analysis Procedures for Gas, Condensate, Brine, and Solids: Pleasant Bayou Well Test, 1988-Present  

Science Conference Proceedings (OSTI)

This section covers analyses performed on gas. Chemical analyses can only be related to well performance if the quantity of the various fluids are known. The IGT on-line data computer system measures the flowrate, the pressures, and the temperatures every 10 seconds. These values are automatically recorded over operator selected intervals both on magnetic media and on paper. This allows review of samples versus operating conditions. This paper covers analyses performed on gas, including: An approximate sampling schedule during flow tests; On-site sample handling and storage of gas samples; Addresses of laboratories that perform off site analyses; Sample shipping instructions; Data archiving; and Quality Control/Quality Assurance. It is expected that the above procedures will change as the flow test progresses, but deviations from the written procedures should be approved by C. Hayden of IGT and noted on the results of the analysis.

Hayden, Chris

1988-01-01T23:59:59.000Z

107

Proposal for a Vehicle Level Test Procedure to Measure Air Conditioning Fuel Use  

SciTech Connect

The air-conditioning (A/C) compressor load significantly impacts the fuel economy of conventional vehicles and the fuel use/range of plug-in hybrid electric vehicles (PHEV). A National Renewable Energy Laboratory (NREL) vehicle performance analysis shows the operation of the air conditioner reduces the charge depletion range of a 40-mile range PHEV from 18% to 30% in a worst case hot environment. Designing for air conditioning electrical loads impacts PHEV and electric vehicle (EV) energy storage system size and cost. While automobile manufacturers have climate control procedures to assess A/C performance, and the U.S. EPA has the SCO3 drive cycle to measure indirect A/C emissions, there is no automotive industry consensus on a vehicle level A/C fuel use test procedure. With increasing attention on A/C fuel use due to increased regulatory activities and the development of PHEVs and EVs, a test procedure is needed to accurately assess the impact of climate control loads. A vehicle thermal soak period is recommended, with solar lamps that meet the SCO3 requirements or an alternative heating method such as portable electric heaters. After soaking, the vehicle is operated over repeated drive cycles or at a constant speed until steady-state cabin air temperature is attained. With this method, the cooldown and steady-state A/C fuel use are measured. This method can be run at either different ambient temperatures to provide data for the GREEN-MAC-LCCP model temperature bins or at a single representative ambient temperature. Vehicles with automatic climate systems are allowed to control as designed, while vehicles with manual climate systems are adjusted to approximate expected climate control settings. An A/C off test is also run for all drive profiles. This procedure measures approximate real-world A/C fuel use and assess the impact of thermal load reduction strategies.

Rugh, J. P.

2010-04-01T23:59:59.000Z

108

Building Energy Simulation Test for Existing Homes (BESTEST-EX): Instructions for Implementing the Test Procedure, Calibration Test Reference Results, and Example Acceptance-Range Criteria  

NLE Websites -- All DOE Office Websites (Extended Search)

Building Energy Simulation Test for Building Energy Simulation Test for Existing Homes (BESTEST-EX): Instructions for Implementing the Test Procedure, Calibration Test Reference Results, and Example Acceptance-Range Criteria Ron Judkoff, Ben Polly, and Marcus Bianchi National Renewable Energy Laboratory Joel Neymark J. Neymark & Associates Mike Kennedy Mike D. Kennedy, Inc. Link to Accompanying Zipped Data Files (3.9 MB) This document is intended for use with the following documents: Building Energy Simulation Test for Existing Homes (BESTEST-EX), NREL/TP-550-47427 Example Procedures for Developing Acceptance-Range Criteria for BESTEST-EX, NREL/TP-550-47502 Technical Report NREL/TP-5500-52414 August 2011 NREL is a national laboratory of the U.S. Department of Energy, Office of Energy

109

Measurements and calculations on the simple up-down adaptive procedure for speech-in-noise tests  

Science Conference Proceedings (OSTI)

The simple up-down adaptive procedure is a common method for measuringspeech reception thresholds. It is used by the Dutch speech-in-noise telephone screening test [National Hearing test; Smits and Houtgast Ear Hear.26

Cas Smits; Tammo Houtgast

2006-01-01T23:59:59.000Z

110

Energy Savings and Peak Demand Reduction of a SEER 21 Heat Pump vs. a SEER 13 Heat Pump with Attic and Indoor Duct Systems  

DOE Green Energy (OSTI)

This report describes results of experiments that were conducted in an unoccupied 1600 square foot house--the Manufactured Housing (MH Lab) at the Florida Solar Energy Center (FSEC)--to evaluate the delivered performance as well as the relative performance of a SEER 21 variable capacity heat pump versus a SEER 13 heat pump. The performance was evaluated with two different duct systems: a standard attic duct system and an indoor duct system located in a dropped-ceiling space.

Cummings, J.; Withers, C.

2011-12-01T23:59:59.000Z

111

Testing and sampling procedures for geothermal-compressured wells. Final report  

DOE Green Energy (OSTI)

Test wells to tap and sample geothermal-geopressured formations at 15,000 to 20,000 feet in the Gulf Coast area can be drilled routinely utilizing available equipment and methods. Electrical logs, surveys and fluid samplers can be used to obtain accurate and reliable information as to depths, temperatures, pressures, and fluid content of the geopressured formations before the well is completed. But it will be necessary to set casing and flow the well, at least temporarily, to secure fluid production volume and pressure data to evaluate the producibility of the geopressured resource. Electric logging and wireline survey methods are fully developed techniques for measuring the parameters needed to assess a geopressured zone before setting casing. Formation subsidence, though it may be slow to develop, can be measured during radioactivity tracer surveys. The following conclusions are drawn: existing well logging and surveying methods and equipment are generally satisfactory for testing and sampling a geothermal-geopressured resource; no significant areas of research are needed to predict, detect, and evaluate geopressured formations for their potential as geothermal resources. Static and dynamic testing procedures using existing technology are satisfactory to test, sample, and analyze a geopressured reservoir.

Boyd, W.E.

112

Alternative Fuel Evaluation Program: Alternative Fuel Light Duty Vehicle Project - Data collection responsibilities, techniques, and test procedures  

DOE Green Energy (OSTI)

This report describes the data gathering and analysis procedures that support the US Department of Energy's implementation of the Alternative Motor Fuels Act (AMFA) of 1988. Specifically, test procedures, analytical methods, and data protocols are covered. The aim of these collection and analysis efforts, as mandated by AMFA, is to demonstrate the environmental, economic, and performance characteristics of alternative transportation fuels.

Not Available

1992-07-01T23:59:59.000Z

113

Alternative Fuel Evaluation Program: Alternative Fuel Light Duty Vehicle Project - Data collection responsibilities, techniques, and test procedures  

DOE Green Energy (OSTI)

This report describes the data gathering and analysis procedures that support the US Department of Energy`s implementation of the Alternative Motor Fuels Act (AMFA) of 1988. Specifically, test procedures, analytical methods, and data protocols are covered. The aim of these collection and analysis efforts, as mandated by AMFA, is to demonstrate the environmental, economic, and performance characteristics of alternative transportation fuels.

Not Available

1992-07-01T23:59:59.000Z

114

Grid Interconnection and Performance Testing Procedures for Vehicle-To-Grid (V2G) Power Electronics: Preprint  

DOE Green Energy (OSTI)

Bidirectional power electronics can add vehicle-to-grid (V2G) capability in a plug-in vehicle, which then allows the vehicle to operate as a distributed resource (DR). The uniqueness of the battery-based V2G power electronics requires a test procedure that will not only maintain IEEE interconnection standards, but can also evaluate the electrical performance of the vehicle working as a DR. The objective of this paper is to discuss a recently published NREL technical report that provides interim test procedures for V2G vehicles for their integration into the electrical distribution systems and for their performance in terms of continuous output power, efficiency, and losses. Additionally, some other test procedures are discussed that are applicable to a V2G vehicle that desires to provide power reserve functions. A few sample test results are provided based on testing of prototype V2G vehicles at NREL.

Kramer, W.; Chakraborty, S.; Kroposki, B.; Hoke, A.; Martin, G.; Markel, T.

2012-03-01T23:59:59.000Z

115

Functional test procedure, Fifth Wheel: SS-R42351, Issue D  

SciTech Connect

This report describes the equipment required for initial assembly/maintenance and inspection/resetting of the Fifth Wheel system. It also gives a step-by-step procedure for initial assembly/maintenance inspection and procedures for resetting the system and Eager-Pac installation. The Fifth Wheel system is associated with a tractor-type vehicle used for materials handling.

1994-07-12T23:59:59.000Z

116

Proposal for a Vehicle Level Test Procedure to Measure Air Conditioning Fuel Use: Preprint  

DOE Green Energy (OSTI)

A procedure is described to measure approximate real-world air conditioning fuel use and assess the impact of thermal load reduction strategies in plug-in hybrid electric vehicles.

Rugh, J.

2010-02-01T23:59:59.000Z

117

Deviation to the Test Program and Procedures for the 710 Critical Experiment Reactor Control Drum Mockup Experiment  

SciTech Connect

This document describes a deviation from the "Test Program and Procedures for the 710 Critical Experiment Reactor Control Drum Mockup Experiment," TM-64-3-706, which was made in accordance with ITS Standard Practice J80-81 on September 14, 1964. The deviation did not involve a significant change in the safety of the operation.

Sims, F.L.

1964-09-14T23:59:59.000Z

118

10 MWe solar pilot plant, Daggett, California. Flushing and steam blows preoperational test procedure 980. Revision: 0  

Science Conference Proceedings (OSTI)

Prescribed steps are given for flushing and steam blowing the condenser hotwell, deaerator, inline demineralizers, thermal storage subsystem flash tank, and steam lines of the Barstow Solar Pilot Plant. Included are acceptance criteria, precautions, a list of test equipment, initial conditions, procedures and data collection, and system restoration. (LEW)

Williams, D.L.

1980-01-01T23:59:59.000Z

119

Interim Test Procedures for Evaluating Electrical Performance and Grid Integration of Vehicle-to-Grid Applications  

DOE Green Energy (OSTI)

The objective of this report is to provide a test plan for V2G testing. The test plan is designed to test and evaluate the vehicle's power electronics capability to provide power to the grid, and to evaluate the vehicle's ability to connect and disconnect from the utility according to a subset of the IEEE Std. 1547 tests.

Chakraborty, S.; Kramer, W.; Kroposki, B.; Martin, G.; McNutt, P.; Kuss, M.; Markel, T.; Hoke, A.

2011-06-01T23:59:59.000Z

120

Interim Test Procedures for Evaluating Electrical Performance and Grid Integration of Vehicle-to-Grid Applications  

SciTech Connect

The objective of this report is to provide a test plan for V2G testing. The test plan is designed to test and evaluate the vehicle's power electronics capability to provide power to the grid, and to evaluate the vehicle's ability to connect and disconnect from the utility according to a subset of the IEEE Std. 1547 tests.

Chakraborty, S.; Kramer, W.; Kroposki, B.; Martin, G.; McNutt, P.; Kuss, M.; Markel, T.; Hoke, A.

2011-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

13 SEER Standard for Central Air Conditioners and Heat Pumps (released in AEO2005)  

Reports and Publications (EIA)

In January 2004, after years of litigation in a case that pitted environmental groups and Attorneys General from 10 States against the U.S. Secretary of Energy, the U.S. Court of Appeals for the Second Circuit reestablished the central air conditioner and heat pump standard originally set in January 2001 [3]. The Courts ruling, which struck down a May 2002 rollback of the 2001 standard to a 12 SEER, mandates that all new central air conditioners and heat pumps meet a 13 SEER standard by January 2006, requiring a 30-percent increase in efficiency relative to current law. The AEO2005 reference case incorporates the 13 SEER standard as mandated by the Courts ruling.

Information Center

2005-04-01T23:59:59.000Z

122

Verification/acceptance test plan/procedure for Acromag calibration system  

SciTech Connect

The purpose of this document is to describe and document the test of the Acromag calibration system software. The purpose of this test is to verify that the Acromag Calibration System (ACS) will reliably test the Acromag thermocouple (TC) type input modules and provide a file showing the temperatures at which the modules are tested, the response rom the Acromag station, instrument data, technician data, and date and time of the test. The ACS consists of a thermocouple calibration unit (TCU), a DOS based computer, a hand held resistance temperature detector (RTD) surface probe and connects to a field installed or a bench Acromag unit.

Fordham, C.R.

1994-12-01T23:59:59.000Z

123

Light-Duty Alternative Fuel Vehicles: Federal Test Procedure Emissions Results  

DOE Green Energy (OSTI)

In support of the U.S. Department of Energy's development and deployment of alternative fuels for environmental and national security reasons, NREL has managed a series of light-duty vehicle emissions tests on alternative fuel vehicles (AFVs). The purpose of this report is to give a detailed evaluation of the final emissions test results on vehicles tested on methanol, ethanol, and compressed natural gas.

Kelly, K.; Eudy, L.; Coburn, T.

1999-12-13T23:59:59.000Z

124

Developing Test Procedures for Measuring Stored Thermal Energy in Firefighter Protective Clothing.  

E-Print Network (OSTI)

??This research studied stored thermal energy in fire fighter's turnout systems. It developed a novel laboratory apparatus and test protocols for measuring the contribution of… (more)

Eni, Egbe Uchechi

2005-01-01T23:59:59.000Z

125

CiteSeer-API:Towards Seamless Resource Location and Interlinking for Digital Libraries  

E-Print Network (OSTI)

functionalities offered by CiteSeer services, including full text search of documents and citations and citation-PMH, including full text document and citation search and citation-based document discovery. Our motivations both document and citation full text search, each method returning respectively a list of matching

Giles, C. Lee

126

Acceptance test procedure for removal of CS1K circuit switcher block and trip schemes  

Science Conference Proceedings (OSTI)

This supporting document provides a detailed process to test the functions of the circuit switcher, protective relays, alarms, SCADA and 125VDC control logic of 115kV and 13.8kV systems at B3S4 substation following the removal of trip and blocking schemes to Transformer No.1 Circuit Switcher B594.

HACHE, J.M.

1999-08-25T23:59:59.000Z

127

Toxic Characteristic Leaching Procedure (TCLP) Testing of Waste Glass and K-3 Refractory  

Science Conference Proceedings (OSTI)

The U. S. Environmental Protection Agency (EPA) issued revised Resource Conservation and Recovery Act (RCRA) Phase IV Land Disposal Restrictions (LDR's) on May 26 1998. The new regulation requires that any waste characteristically hazardous for the metals As, Ba, Cd, Cr, Pb, Hg, Se, and Ag will have to be treated to meet the LDR Universal Treatment Standards (UTS) for each metal prior to land disposal. Since EPA regulations continue to become more stringent, here-to-fore unpublished TCLP data generated during testing of simulated High Level Waste (HLW) glass, including the Evnironmental Assessment glass and K-3 melter refractory, will be reviewed. The refractory TCLP data compilation includes K-3 refractory in contact with DWPF simulated glass in a pilot scale melter and K-3 refractory in contact with actual mixed waste glass in a 5 ton a day GTS Duratek melter.

Jantzen, C.M.

1999-04-23T23:59:59.000Z

128

Base program interim phase test procedure - Coherent Laser Vision System (CLVS). Final report, September 27, 1994--January 30, 1997  

Science Conference Proceedings (OSTI)

The purpose of the CLVS research project is to develop a prototype fiber-optic based Coherent Laser Vision System suitable for DOE`s EM Robotics program. The system provides three-dimensional (3D) vision for monitoring situations in which it is necessary to update geometrics on the order of once per second. The CLVS project plan required implementation in two phases of the contract, a Base Contract and a continuance option. This is the Test Procedure and test/demonstration results presenting a proof-of-concept for a system providing three-dimensional (3D) vision with the performance capability required to update geometrics on the order of once per second.

NONE

1997-05-01T23:59:59.000Z

129

A Discussion of Procedures and Equipment for the Comprehensive Test Ban Treaty On-Site Inspection Environmental Sampling and Analysis  

SciTech Connect

This paper is intended to serve as a scientific basis to start discussions of the available environmental sampling techniques and equipment that have been used in the past that could be considered for use within the context of the Comprehensive Nuclear-Test-Ban Treaty (CTBT) on-site inspections (OSI). This work contains information on the techniques, equipment, costs, and some operational procedures associated with environmental sampling that have actually been used in the past by the United States for the detection of nuclear explosions. This paper also includes a discussion of issues, recommendations, and questions needing further study within the context of the sampling and analysis of aquatic materials, atmospheric gases, atmospheric particulates, vegetation, sediments and soils, fauna, and drill-back materials.

Wogman, Ned A.; Milbrath, Brian D.; Payne, Rosara F.; Seifert, Carolyn E.; Friese, Judah I.; Miley, Harry S.; Bowyer, Ted W.; Hanlen, Richard C.; Onishi, Yasuo; Hayes, James C.; Wigmosta, Mark S.

2011-02-01T23:59:59.000Z

130

RFID Interference Test Procedures  

Science Conference Proceedings (OSTI)

... GHz. Active tags contain a power source (eg, battery) and permit higher read ranges and/or lower reader power. Passive ...

2010-10-05T23:59:59.000Z

131

Visualizing large-scale data in educational, behavioral, psychometrical and social sciences: utilities and design patterns of the SEER computational and graphical statistics  

Science Conference Proceedings (OSTI)

This paper introduces a graphical method SEE Repeated-measure data (SEER) to visually analyze data commonly collected in large-scale surveys, market research, biostatistics, and educational and psychological measurement. Many researchers in these disciplines ... Keywords: SEER, computational statistics, data visualization, large-scale data, research methodology, social and behavioral sciences

Christopher WT Chiu; Peter Pashley; Marilyn Seastrom; Peggy Carr

2005-10-01T23:59:59.000Z

132

Analytical Solution of a Simplified Transport Problem with Continuous Energy for Testing Monte Carlo Procedures,” this conference  

E-Print Network (OSTI)

A simplified transport problem is presented with continuous energy and neutrons moving only into the +X and –X direction. An exact analytical solution is given with a 1/E energy dependence of the space, direction and energy dependent neutron flux. The source function, which also behaves basically as 1/E has to be modified for a certain energy range if a maximum energy is introduced in the problem. At the cost of more complicated mathematics the total and scattering cross sections and the anisotropy of scattering may very with energy. This model can be implemented in a general purpose Monte Carlo code like MCNP5 without modification, but needs a specially prepared cross section library file. The model can be applied to test Monte Carlo procedures, like the generation of multi-group cross section and scattering matrices which can be calculated analytically from the continuous-energy cross section data. From the adjoint equation the optimum importance function can be derived, which can be used to devise a continuous-energy zero-variance Monte Carlo scheme. Key Words: transport problem, analytical solution, continuous energy, Monte Carlo 1.

J. Eduard Hoogenboom

2007-01-01T23:59:59.000Z

133

Strategies for Energy-Efficient Remodeling: SEER 2003 Case Study Report; February 27, 2003 -- October 31, 2004  

Science Conference Proceedings (OSTI)

The goal of the Strategies for Energy Efficiency in Remodeling (SEER) project is to provide information, based on research and case studies, to remodelers and consumers about opportunities to increase home energy performance. Opportunities to include energy efficiency often arise while undertaking general remodeling work. This case study report examines the technologies, methods, and installation of specific energy efficiency strategies. The information presented here stems from a ''gut rehab'' of a house in rural New Jersey as part of the SEER project through the Building America Existing Buildings Program.

Drumheller, S. C.; Wiehagen, J.

2004-11-01T23:59:59.000Z

134

The Use of Radiation Therapy Appears to Improve Outcome in Patients With Malignant Primary Tracheal Tumors: A SEER-Based Analysis  

SciTech Connect

Purpose: To conduct a matched pair analysis assessing the impact of radiotherapy (RT) in patients with resectable and unresectable primary malignant tracheal tumors using Surveillance, Epidemiology and End Results (SEER) database. Patients and Methods: The SEER registry was used to identify every patient (or 'case') who received RT between 1988 and 2007 for primary malignant tracheal tumors, and to search for corresponding 'controls' (not treated with RT), with the same prognostic and treatment factors (surgery on the trachea, disease extension, histology, and gender). Overall survival (OS) was calculated with the Kaplan-Meier methods. Results of OS and cumulative incidence of death from tracheal cancer in the cases and controls, and in various subsets, were compared using log-rank and Gray's tests. Results: Two hundred fifty-eight patients who received RT were identified, and 78 of these had appropriate matched controls identified, forming the basis of this analysis. In the 78 (+RT) cases, the median follow-up was 60 months (range, 10-192) in the survivors vs. 55 months (range, 2-187) in the controls (no-RT group). Patients in RT group had significantly better OS, and a lower cumulative incidence of death from tracheal cancer than no-RT patients (p < 0.05). Treatment with radiation was associated with improved survival in patients with squamous cell histology [p < 0.0001], regional disease extension [p = 0.030], or those that did not undergo resection [p = 0.038]. There were four deaths in RT group and three in no-RT group attributed to cardiac and respiratory causes. Conclusion: Our data suggest a survival benefit for the use of RT broadly for all patients with tracheal cancer. Nevertheless, the retrospective nature of this observational study limits its interpretation.

Xie Liyi [Department of Radiation Oncology, Fudan University Shanghai Cancer Center and Department of Oncology, Shanghai Medical College, Fudan University, Shanghai (China) [Department of Radiation Oncology, Fudan University Shanghai Cancer Center and Department of Oncology, Shanghai Medical College, Fudan University, Shanghai (China); Department of Radiation Oncology, University of North Carolina, Chapel Hill, NC (United States); Fan Min [Department of Radiation Oncology, Fudan University Shanghai Cancer Center and Department of Oncology, Shanghai Medical College, Fudan University, Shanghai (China)] [Department of Radiation Oncology, Fudan University Shanghai Cancer Center and Department of Oncology, Shanghai Medical College, Fudan University, Shanghai (China); Sheets, Nathan C.; Chen, Ronald C. [Department of Radiation Oncology, University of North Carolina, Chapel Hill, NC (United States)] [Department of Radiation Oncology, University of North Carolina, Chapel Hill, NC (United States); Jiang, Guo-Liang, E-mail: jianggl@shca.org.cn [Department of Radiation Oncology, Fudan University Shanghai Cancer Center and Department of Oncology, Shanghai Medical College, Fudan University, Shanghai (China)] [Department of Radiation Oncology, Fudan University Shanghai Cancer Center and Department of Oncology, Shanghai Medical College, Fudan University, Shanghai (China); Marks, Lawrence B., E-mail: marks@med.unc.edu [Department of Radiation Oncology, University of North Carolina, Chapel Hill, NC (United States)

2012-10-01T23:59:59.000Z

135

Deviation of the Test Program and Procedures for the 710 Critical Experiment Reactor Related to Changes in the core Material Volume Fractions  

SciTech Connect

This document describes a deviation from the "Test Program and Procedures for the 710 Critical Experiment Reactor Loading and Rod Calibrations," TM-63-1-702, which was made in accordance with ITS Standard Practice J80-81 on March 13, 1963. The deviation did not involve a significant change in the safety of the operation.

Sims, F.L.

1963-03-13T23:59:59.000Z

136

Evaluation of potential modifications to the SEER (Simplified Estimation of Exposure to Radiation) fallout code. Technical report, 1 August 1982-1 August 1983  

Science Conference Proceedings (OSTI)

This report presents the methodology and results of an attempt to modify and improve the computer code SEER (Simplified Estimation of Exposure to Radiation). SEER, part of the large nuclear weapon damage-assessment code CIVIC, was developed in the early 1970s with the intent that it simulate the fallout exposure-rate contours of DELFIC (Defense Land Fallout Interpretive code) while using a minimal amount of computer time. A problem that surfaced with the development of SEER was the fact that the SEER methodology leads to an overprediction of the total activity deposited on the ground. In order to compensate for this characteristic, SAI has lowered the value of the K-factor in the SEER portion of CIVIC to approximately half of the original value. The K-factor is the amount of weapon fallout activity per unit yield, distributed over unit area. Its value is not precisely known, in part because the percentage of total radioactive debris that constitutes early fallout (as opposed to that which is lofted to high altitudes and carried off beyond local fallout distances) is not well known and varies with height of burst and other conditions. This work effort investigated the possibility of modifying the SEER methodology so that activity is conserved and a good approximation to DELFIC results could be obtained without resort to the adjustment of the K-factor.

Edwards, R.C.

1983-09-01T23:59:59.000Z

137

Battery Usage and Thermal Performance of the Toyota Prius and Honda Insight for Various Chassis Dynamometer Test Procedures: Preprint  

DOE Green Energy (OSTI)

This study describes the results from the National Renewable Energy Laboratory's (NREL) chassis dynamometer testing of a 2000 model year Honda Insight and 2001 model year Toyota Prius. The tests were conducted for the purpose of evaluating the battery thermal performance, assessing the impact of air conditioning on fuel economy and emissions, and providing information for NREL's Advanced Vehicle Simulator (ADVISOR).

Kelly, K. J.; Mihalic, M.; Zolot, M.

2001-11-20T23:59:59.000Z

138

Test Procedure for 170.304 e Clinical Decision Support APPROVED Version 1.1 September 24, 2010  

E-Print Network (OSTI)

; and laboratory test results. 1 Department of Health and Human Services, 45 CFR Part 170 Health Information in 45 CFR Part 170 Subpart C of the Final Rule for Health Information Technology: Initial Set of standards, Implementation Specifications, and Certification Criteria for Electronic Health Record Technology

139

Test Procedure for 170.306.c Clinical Decision Support APPROVED Version 1.1 September 24, 2010  

E-Print Network (OSTI)

; and laboratory test results. 1 Department of Health and Human Services, 45 CFR Part 170 Health Information in 45 CFR Part 170 Subpart C of the Final Rule for Health Information Technology: Initial Set of standards, Implementation Specifications, and Certification Criteria for Electronic Health Record Technology

140

Emergency Procedures  

Energy.gov (U.S. Department of Energy (DOE))

Note: This page is pending deletion, please refer to the Safety and health main page for emergency procedure information:

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Adjuvant Brachytherapy Removes Survival Disadvantage of Local Disease Extension in Stage IIIC Endometrial Cancer: A SEER Registry Analysis  

SciTech Connect

Purpose: To assess the role of radiotherapy (RT) in women with Stage IIIC endometrial cancer. Methods and Materials: The 17-registry Survival, Epidemiology, and End Results (SEER) database was searched for patients with lymph node-positive non-Stage IV epithelial endometrial cancer diagnosed and treated between 1988 and 1998. Two subgroups were identified: those with organ-confined Stage IIIC endometrial cancer and those with Stage IIIC endometrial cancer with direct extension of the primary tumor. RT was coded as external beam RT (EBRT) or brachytherapy (BT). Observed survival (OS) was reported with a minimum of 5 years of follow-up; the survival curves were compared using the log-rank test. Results: The therapy data revealed 611 women with Stage IIIC endometrial cancer during this period. Of these women, 51% were treated with adjuvant EBRT, 21% with EBRT and BT, and 28% with no additional RT (NAT). Of the 611 patients, 293 had organ-confined Stage IIIC endometrial cancer and 318 patients had Stage IIIC endometrial cancer with direct extension of the primary tumor. The 5-year OS rate for all patients was 40% with NAT, 56% after EBRT, and 64% after EBRT/BT. Adjuvant RT improved survival compared with NAT (p <0.001). In patients with organ-confined Stage IIIC endometrial cancer, the 5-year OS rate was 50% for NAT, 64% for EBRT, and 67% for EBRT/BT. Again, adjuvant RT contributed to improved survival compared with NAT (p = 0.02). In patients with Stage IIIC endometrial cancer and direct tumor extension, the 5-year OS rate was 34% for NAT, 47% for EBRT, and 63% for EBRT/BT. RT improved OS compared with NAT (p <0.001). Also, in this high-risk subgroup, adding BT to EBRT was superior to EBRT alone (p = 0.002). Conclusion: Women with Stage IIIC endometrial cancer receiving adjuvant EBRT and EBRT/BT had improved OS compared with patients receiving NAT. When direct extension of the primary tumor was present, the addition of BT to EBRT was even more beneficial.

Rossi, Peter J. [Department of Radiation Oncology, Emory University School of Medicine, Atlanta, GA (United States)], E-mail: rossi@radonc.emory.org; Jani, Ashesh B. [Department of Radiation Oncology, Emory University School of Medicine, Atlanta, GA (United States); Horowitz, Ira R. [Department of Obstetrics and Gynecology, Emory University School of Medicine, Atlanta, GA (United States); Johnstone, Peter A.S. [Department of Radiation Oncology, Emory University School of Medicine, Atlanta, GA (United States)

2008-01-01T23:59:59.000Z

142

HVAC BESTEST: A Procedure for Testing the Ability of Whole-Building Energy Simulation Programs to Model Space Conditioning Equipment: Preprint  

DOE Green Energy (OSTI)

Validation of Building Energy Simulation Programs consists of a combination of empirical validation, analytical verification, and comparative analysis techniques (Judkoff 1988). An analytical verification and comparative diagnostic procedure was developed to test the ability of whole-building simulation programs to model the performance of unitary space-cooling equipment that is typically modeled using manufacturer design data presented as empirically derived performance maps. Field trials of the method were conducted by researchers from nations participating in the International Energy Agency (IEA) Solar Heating and Cooling (SHC) Programme Task 22, using a number of detailed hourly simulation programs from Europe and the United States, including: CA-SIS, CLIM2000, PROMETHEUS, TRNSYS-TUD, and two versions of DOE-2.1E. Analytical solutions were also developed for the test cases.

Neymark, J,; Judkoff, R.; Knabe, G.; Le, H.-T.; Durig, M.; Glass, A.; Zweifel, G.

2001-07-03T23:59:59.000Z

143

Test procedures and protocols: Their relevance to the figure of merit for thermal distribution systems. Volume 1: Informal report  

Science Conference Proceedings (OSTI)

A conceptual framework is developed that categorizes measurement protocols for forced-air thermal distribution systems in small buildings. This framework is based on the distinction between two generic approaches. The {open_quote}system-comparison{close_quote} approach seeks to determine, via a pair of whole-house energy-use measurements, the difference in energy use between the house with the as-found duct system and the same house with no energy losses attributable to the thermal distribution system. The {open_quote}component loss-factor{close_quote} approach identifies and measures the individual causes of duct losses, and then builds up a value for the net overall duct efficiency, usually with the help of computer simulation. Examples of each approach are analyzed and related to a proposed Figure of Merit for thermal distribution systems. This Figure of Merit would serve as the basis for a Standard Method of Test analogous to those already in place for furnaces, boilers, air conditioners, and heat pumps.

Andrews, J.W.

1993-09-01T23:59:59.000Z

144

TEST PLAN AND PROCEDURE FOR THE EXAMINATION OF TANK 241-AY-101 MULTI-PROBE CORROSION MONITORING SYSTEM  

SciTech Connect

This test plan describes the methods to be used in the forensic examination of the Multi-probe Corrosion Monitoring System (MPCMS) installed in the double-shell tank 241-AY-101 (AY-101). The probe was designed by Applied Research and Engineering Sciences (ARES) Corporation. The probe contains four sections, each of which can be removed from the tank independently (H-14-107634, AY-101 MPCMS Removable Probe Assembly) and one fixed center assembly. Each removable section contains three types of passive corrosion coupons: bar coupons, round coupons, and stressed C-rings (H-14-l07635, AY-101 MPCMS Details). Photographs and weights of each coupon were recorded and reported on drawing H-14-107634 and in RPP-RPT-40629, 241-AY-101 MPCMS C-Ring Coupon Photographs. The coupons will be the subject of the forensic analyses. The purpose of this examination will be to document the nature and extent of corrosion of the 29 coupons. This documentation will consist of photographs and photomicrographs of the C-rings and round coupons, as well as the weights of the bar and round coupons during corrosion removal. The total weight loss of the cleaned coupons will be used in conjunction with the surface area of each to calculate corrosion rates in mils per year. The bar coupons were presumably placed to investigate the liquid-air-interface. An analysis of the waste level heights in the waste tank will be investigated as part of this examination.

WYRWAS RB; PAGE JS; COOKE GS

2012-04-19T23:59:59.000Z

145

Developing Fatigue Pre-crack Procedure to Evaluate Fracture Toughness of Pipeline Steels Using Spiral Notch Torsion Test  

SciTech Connect

The spiral notch torsion test (SNTT) has been utilized to investigate the crack growth behavior of X52 steel base and welded materials used for hydrogen infrastructures. The X52 steel materials are received from a welded pipe using friction stir welding techniques. Finite element models were established to study the crack growth behavior of steel SNTT steel samples, which were assumed to be isotropic material. A series SNTT models were set up to cover various crack penetration cases, of which the ratios between crack depth to diameter (a/D ratio) ranging from 0.10 to 0.45. The evolution of compliance and energy release rates in the SNTT method have been investigated with different cases, including different geometries and materials. Indices of characteristic compliance and energy release rates have been proposed. Good agreement has been achieved between predictions from different cases in the same trend. These work shed lights on a successful protocol for SNTT application in wide range of structural materials. The further effort needed for compliance function development is to extend the current developed compliance function to the deep crack penetration arena, in the range of 0.55 to 0.85 to effectively determine fracture toughness for extremely tough materials.

Wang, Jy-An John [ORNL; Tan, Ting [ORNL; Jiang, Hao [ORNL; Zhang, Wei [ORNL; Feng, Zhili [ORNL

2012-10-01T23:59:59.000Z

146

CMS Procedure  

Science Conference Proceedings (OSTI)

... Tabletop Exercise. Tailoring. Tape Management System. Technical Safeguard. Tempest. Test Plan. Test. Threat Agent. Threat Analysis. ...

2009-06-30T23:59:59.000Z

147

Predictors of IMRT and Conformal Radiotherapy Use in Head and Neck Squamous Cell Carcinoma: A SEER-Medicare Analysis  

SciTech Connect

Purpose: The extent to which new techniques for the delivery of radiotherapy for head and neck squamous cell carcinoma (HNSCC) have diffused into clinical practice is unclear, including the use of 3-dimensional conformal RT (3D-RT) and intensity-modulated radiation therapy (IMRT). Methods and Materials: Using the Surveillance, Epidemiology, and End Results (SEER)-Medicare linked database, we identified 2,495 Medicare patients with Stage I-IVB HNSCC diagnosed at age 65 years or older between 2000 and 2005 and treated with either definitive (80%) or adjuvant (20%) radiotherapy. Our primary aim was to analyze the trends and predictors of IMRT use over this time, and the secondary aim was a similar description of the trends and predictors of conformal radiotherapy (CRT) use, defined as treatment with either 3D-RT or IMRT. Results: Three hundred sixty-four (15%) patients were treated with IMRT, and 1,190 patients (48%) were treated with 3D-RT. Claims for IMRT and CRT rose from 0% to 33% and 39% to 86%, respectively, between 2000 and 2005. On multivariable analysis, IMRT use was associated with SEER region (West 18%; Northeast 11%; South 12%; Midwest 13%), advanced stage (advanced, 21%; early, 9%), non-larynx site (non-larynx, 23%; larynx, 7%), higher median census tract income (highest vs. lowest quartile, 18% vs. 10%), treatment year (2003-2005, 31%; 2000-2002, 6%), use of chemotherapy (26% with; 9% without), and higher radiation oncologist treatment volume (highest vs. lowest tertile, 23% vs. 8%). With CRT as the outcome, only SEER region, treatment year, use of chemotherapy, and increasing radiation oncologist HNSCC volume were significant on multivariable analysis. Conclusions: The use of IMRT and CRT by Medicare beneficiaries with HNSCC rose significantly between 2000 and 2005 and was associated with both clinical and non-clinical factors, with treatment era and radiation oncologist HNSCC treatment volume serving as the strongest predictors of IMRT use.

Sher, David J., E-mail: dsher@lroc.harvard.edu [Department of Radiation Oncology, Dana-Farber Cancer Institute and Brigham and Women's Hospital, Boston, MA (United States); Center for Outcomes and Policy Research, Dana Farber Cancer Institute, Boston, MA (United States); Neville, Bridget A. [Center for Outcomes and Policy Research, Dana Farber Cancer Institute, Boston, MA (United States); Chen, Aileen B. [Department of Radiation Oncology, Dana-Farber Cancer Institute and Brigham and Women's Hospital, Boston, MA (United States); Center for Outcomes and Policy Research, Dana Farber Cancer Institute, Boston, MA (United States); Schrag, Deborah [Center for Outcomes and Policy Research, Dana Farber Cancer Institute, Boston, MA (United States)

2011-11-15T23:59:59.000Z

148

Set Top Boxes Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

Commission. Jessie F. Quichocho, Division of Policy and Rulemaking, Office of Nuclear Reactor Regulation. FR Doc. 2011-32389 Filed 12-15-11; 8:45 am BILLING CODE 7590-01-P...

149

Mobile Energy Laboratory Procedures  

SciTech Connect

Pacific Northwest Laboratory (PNL) has been tasked to plan and implement a framework for measuring and analyzing the efficiency of on-site energy conversion, distribution, and end-use application on federal facilities as part of its overall technical support to the US Department of Energy (DOE) Federal Energy Management Program (FEMP). The Mobile Energy Laboratory (MEL) Procedures establish guidelines for specific activities performed by PNL staff. PNL provided sophisticated energy monitoring, auditing, and analysis equipment for on-site evaluation of energy use efficiency. Specially trained engineers and technicians were provided to conduct tests in a safe and efficient manner with the assistance of host facility staff and contractors. Reports were produced to describe test procedures, results, and suggested courses of action. These reports may be used to justify changes in operating procedures, maintenance efforts, system designs, or energy-using equipment. The MEL capabilities can subsequently be used to assess the results of energy conservation projects. These procedures recognize the need for centralized NM administration, test procedure development, operator training, and technical oversight. This need is evidenced by increasing requests fbr MEL use and the economies available by having trained, full-time MEL operators and near continuous MEL operation. DOE will assign new equipment and upgrade existing equipment as new capabilities are developed. The equipment and trained technicians will be made available to federal agencies that provide funding for the direct costs associated with MEL use.

Armstrong, P.R.; Batishko, C.R.; Dittmer, A.L.; Hadley, D.L.; Stoops, J.L.

1993-09-01T23:59:59.000Z

150

Proceedings of second geopressured geothermal energy conference, Austin, Texas, February 23--25, 1976. Volume II. Resource assessment. [Geologic procedures for test- or industrial-site selection along Texas Gulf coast  

DOE Green Energy (OSTI)

This report describes techniques being used in the assessment of geopressured geothermal resources along the Texas Gulf Coast and defines geologic procedures for test- or industrial-site selection. These approaches have been proven in petroleum exploration and are applicable in geothermal exploration here in the Gulf basin and in other sedimentary basins.

Bebout, D.G.

1976-01-01T23:59:59.000Z

151

Call Forwarding: New NIST Procedure Could Speed Cell ...  

Science Conference Proceedings (OSTI)

Call Forwarding: New NIST Procedure Could Speed Cell Phone Testing. For Immediate Release: March 2, 2010. ...

2010-10-05T23:59:59.000Z

152

DOE/EA-1673: Environmental Assessment for Energy Conservation Program for Certain Industrial Equipment: Energy Conservation Standards and Test Procedures for Commercial Heating, Air-Conditioning, and Water-Heating Equipment (July 2009)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 Environmental Assessment for 10 CFR 431 Energy Conservation Program for Certain Industrial Equipment: Energy Conservation Standards and Test Procedures for Commercial Heating, Air- Conditioning, and Water-Heating Equipment July 2009 8-i CHAPTER 8. ENVIRONMENTAL ASSESSMENT TABLE OF CONTENTS 8.1 INTRODUCTION ............................................................................................................... 8-1 8.2 AIR QUALITY ANALYSIS ............................................................................................... 8-1 8.3 AIR POLLUTANT DESCRIPTIONS ................................................................................ 8-1 8.4 AIR QUALITY REGULATIONS ...................................................................................... 8-3

153

Comparison of Test Procedures and Energy Efficiency Criteria in Selected International Standards and Labeling Programs for Clothes Washers, Water Dispensers, Vending Machines and CFLs  

E-Print Network (OSTI)

etc. ) during which energy consumption is measured, the typedoes not specify energy consumption measurements but rather,test in which water and energy consumption are measured. The

Fridley, David

2010-01-01T23:59:59.000Z

154

Acceptance Test Procedure for Project 251W, WBS 3, Substation A-8, Building 251-W, Bus {number_sign}2 switchgear replacement  

Science Conference Proceedings (OSTI)

This document records the steps taken and results of the acceptance testing of the new 13.8kV switchgear installed at 251W. This gear is under the administrative control of Electrical Utilities.

VanBaalen, R.A.

1995-02-01T23:59:59.000Z

155

Nondestructive Evaluation: Plant-Specific Applications of Qualified Nozzle Inner Radius and Nozzle-to-Shell Weld Ultrasonic Testing Procedures Using EPRI Computer Models -- 2002-2010  

Science Conference Proceedings (OSTI)

This report is the fourth in a series of periodic technical updates documenting plant-specific applications of qualified nozzle inner radius and nozzle-to-shell weld ultrasonic testing techniques developed using the Electric Power Research Institute Nondestructive Evaluation programs three-dimensional nozzle models. This particular update covers the period 20022010.

2010-11-16T23:59:59.000Z

156

Improving Ventilation and Saving Energy: Laboratory Study in aModular Classroom Test Bed  

SciTech Connect

The primary goals of this research effort were to develop, evaluate, and demonstrate a practical HVAC system for classrooms that consistently provides classrooms with the quantity of ventilation in current minimum standards, while saving energy, and reducing HVAC-related noise levels. This research was motivated by several factors, including the public benefits of energy efficiency, evidence that many classrooms are under-ventilated, and public concerns about indoor environmental quality in classrooms. This project involved the installation and verification of the performance of an Improved Heat Pump Air Conditioning (IHPAC) system, and its comparison, a standard HVAC system having an efficiency of 10 SEER. The project included the verification of the physical characteristics suitable for direct replacement of existing 10 SEER systems, quantitative demonstration of improved energy efficiency, reduced acoustic noise levels, quantitative demonstration of improved ventilation control, and verification that the system would meet temperature control demands necessary for the thermal comfort of the occupants. Results showed that the IHPAC met these goals. The IHPAC was found to be a direct bolt-on replacement for the 10 SEER system. Calculated energy efficiency improvements based on many days of classroom cooling or heating showed that the IHPAC system is about 44% more efficient during cooling and 38% more efficient during heating than the 10 SEER system. Noise reduction was dramatic, with measured A-weighed sound level for fan only operation conditions of 34.3 dB(A), a reduction of 19 dB(A) compared to the 10 SEER system. Similarly, the IHPAC stage-1 and stage-2 compressor plus fan sound levels were 40.8 dB(A) and 42.7 dB(A), reductions of 14 and 13 dB(A), respectively. Thus, the IHPAC is 20 to 35 times quieter than the 10 SEER systems depending upon the operation mode. The IHPAC system met the ventilation requirements and was able to provide consistent outside air supply throughout the study. Indoor CO2 levels with simulated occupancy were maintained below 1000 ppm. Finally temperature settings were met and controlled accurately. The goals of the laboratory testing phase were met and this system is ready for further study in a field test of occupied classrooms.

Apte, Michael G.; Buchanan, Ian S.; Faulkner, David; Fisk,William J.; Lai, Chi-Ming; Spears, Michael; Sullivan, Douglas P.

2005-08-01T23:59:59.000Z

157

Slimhole Handbook- Procedures And Recommendations For Slimhole...  

Open Energy Info (EERE)

Slimhole Handbook- Procedures And Recommendations For Slimhole Drilling And Testing In Geothermal Exploration Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Report:...

158

Additional Guidance Regarding Application of Current Procedures...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Additional Guidance Regarding Application of Current Procedures for Testing Energy Consumption of Clothes Washers with Warm Rinse Cycles, Issued: June 30, 2010 Additional Guidance...

159

TEST  

Science Conference Proceedings (OSTI)

This is an abstract. TEST Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras lacinia dui et est venenatis lacinia. Vestibulum lacus dolor, adipiscing id mattis sit amet, ultricies sed purus. Nulla consectetur aliquet feugiat. Maecenas ips

160

Improved Survival With Radiation Therapy in High-Grade Soft Tissue Sarcomas of the Extremities: A SEER Analysis  

Science Conference Proceedings (OSTI)

Purpose: The benefit of radiation therapy in extremity soft tissue sarcomas remains controversial. The purpose of this study was to determine the effect of radiation therapy on overall survival among patients with primary soft tissue sarcomas of the extremity who underwent limb-sparing surgery. Methods and Materials: A retrospective study from the Surveillance, Epidemiology, and End Results (SEER) database that included data from January 1, 1988, to December 31, 2005. A total of 6,960 patients constituted the study population. Overall survival curves were constructed using the Kaplan-Meir method and for patients with low- and high-grade tumors. Hazard ratios were calculated based on multivariable Cox proportional hazards models. Results: Of the cohort, 47% received radiation therapy. There was no significant difference in overall survival among patients with low-grade tumors by radiation therapy. In high-grade tumors, the 3-year overall survival was 73% in patients who received radiation therapy vs. 63% for those who did not receive radiation therapy (p < 0.001). On multivariate analysis, patients with high-grade tumors who received radiation therapy had an improved overall survival (hazard ratio 0.67, 95% confidence interval 0.57-0.79). In patients receiving radiation therapy, 13.5% received it in a neoadjuvant setting. The incidence of patients receiving neoadjuvant radiation did not change significantly between 1988 and 2005. Conclusions: To our knowledge, this is the largest population-based study reported in patients undergoing limb-sparing surgery for soft tissue sarcomas of the extremities. It reports that radiation was associated with improved survival in patients with high-grade tumors.

Koshy, Matthew, E-mail: mkoshy@umm.ed [Department of Radiation Oncology, University of Maryland School of Medicine, Baltimore, MD (United States); Rich, Shayna E. [Department of Epidemiology and Preventive Medicine, University of Maryland School of Medicine, Baltimore, MD (United States); Mohiuddin, Majid M. [Department of Radiation Oncology, University of Maryland School of Medicine, Baltimore, MD (United States)

2010-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Patterns of Care and Locoregional Treatment Outcomes in Older Esophageal Cancer Patients: The SEER-Medicare Cohort  

SciTech Connect

Purpose: Optimal management of elderly patients with nonmetastatic esophageal cancer is unclear. Outcomes data after locoregional treatment are lacking for this group. Methods: We assessed outcomes associated with standard locoregional treatments in 2,626 patients (age > 65 years) from the Surveillance Epidemiology and End Results (SEER)-Medicare cohort diagnosed with nonmetastatic esophageal cancer from 1992 to 2002. In patients treated with radiotherapy alone (RT), surgery alone (S), chemoradiotherapy (CRT), or preoperative chemotherapy followed by surgery (CRT + S), overall and disease-free survival were compared using proportional hazards regression. Postoperative complications were compared using logistic regression. Results: Mean age was 76 {+-} 6 years. Seven percent underwent CRT + S, 39% CRT, 30% S, and 24% RT. One-year survival was 68% (CRT + S), 52% (CRT), 53% (S), and 16% (RT), respectively (p < 0.001). Patients who underwent CRT + S demonstrated improved overall survival compared with S alone (hazard ratio [HR] = 0.81; 95% confidence interval [CI], 0.66-0.98; p = 0.03) and RT (HR = 0.44; 95% CI, 0.35-0.55; p < 0.0001); and comparable survival to CRT (HR = 0.82; 95% CI, 0.67-1.01; p = 0.06). Patients who underwent CRT + S also had comparable postoperative mortality (HR = 0.96; 95% CI, 0.87-1.07; p = 0.45) and complications (OR = 0.89; 95% CI, 0.70-1.14; p = 0.36) compared with S alone. Conclusions: Preoperative chemoradiotherapy may be an acceptable treatment option in appropriately selected older esophageal cancer patients. This treatment modality did not appear to increase surgical complications and offered potential therapeutic benefit, particularly compared with surgery alone.

Smith, Grace L. [Department of Radiation Oncology, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States); Smith, Benjamin D. [Department of Radiation Oncology, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States); Radiation Oncology Flight, Wilford Hall Medical Center, San Antonio, TX (United States); Buchholz, Thomas A.; Liao Zhongxing; Jeter, Melenda [Department of Radiation Oncology, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States); Swisher, Stephen G. M.D.; Hofstetter, Wayne L. [Department of Thoracic and Cardiovascular Surgery, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States); Ajani, Jaffer A. [Department of Gastrointestinal Medical Oncology, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States); McAleer, Mary F.; Komaki, Ritsuko [Department of Radiation Oncology, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States); Cox, James D. [Department of Radiation Oncology, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States)], E-mail: jcox@mdanderson.org

2009-06-01T23:59:59.000Z

162

Infant Brain Tumors: Incidence, Survival, and the Role of Radiation Based on Surveillance, Epidemiology, and End Results (SEER) Data  

SciTech Connect

Purpose: To evaluate the incidence of infant brain tumors and survival outcomes by disease and treatment variables. Methods and Materials: The Surveillance, Epidemiology, and End Results (SEER) Program November 2008 submission database provided age-adjusted incidence rates and individual case information for primary brain tumors diagnosed between 1973 and 2006 in infants less than 12 months of age. Results: Between 1973 and 1986, the incidence of infant brain tumors increased from 16 to 40 cases per million (CPM), and from 1986 to 2006, the annual incidence rate averaged 35 CPM. Leading histologies by annual incidence in CPM were gliomas (13.8), medulloblastoma and primitive neuroectodermal tumors (6.6), and ependymomas (3.6). The annual incidence was higher in whites than in blacks (35.0 vs. 21.3 CPM). Infants with low-grade gliomas had the highest observed survival, and those with atypical teratoid rhabdoid tumors (ATRTs) or primary rhabdoid tumors of the brain had the lowest. Between 1979 and 1993, the annual rate of cases treated with radiation within the first 4 months from diagnosis declined from 20.5 CPM to <2 CPM. For infants with medulloblastoma, desmoplastic histology and treatment with both surgery and upfront radiation were associated with improved survival, but on multivariate regression, only combined surgery and radiation remained associated with improved survival, with a hazard ratio for death of 0.17 compared with surgery alone (p = 0.005). For ATRTs, those treated with surgery and upfront radiation had a 12-month survival of 100% compared with 24.4% for those treated with surgery alone (p = 0.016). For ependymomas survival was higher in patients treated in more recent decades (p = 0.001). Conclusion: The incidence of infant brain tumors has been stable since 1986. Survival outcomes varied markedly by histology. For infants with medulloblastoma and ATRTs, improved survival was observed in patients treated with both surgery and early radiation compared with those treated with surgery alone.

Bishop, Andrew J. [Department of Radiation Oncology, Indiana University School of Medicine, Indianapolis, IN (United States); McDonald, Mark W., E-mail: mwmcdona@iupui.edu [Department of Radiation Oncology, Indiana University School of Medicine, Indianapolis, IN (United States); Indiana University Health Proton Therapy Center, Bloomington, IN (United States); Chang, Andrew L. [Department of Radiation Oncology, Indiana University School of Medicine, Indianapolis, IN (United States); Indiana University Health Proton Therapy Center, Bloomington, IN (United States); Esiashvili, Natia [Department of Radiation Oncology, Emory University School of Medicine, Atlanta, GA (United States)

2012-01-01T23:59:59.000Z

163

Methodology to Develop and Test an Easy-to-use Procedure for the Preliminary Selection of High-performance Systems for Office Buildings in Hot and Humid Climates  

E-Print Network (OSTI)

A procedure has been developed for the preliminary selection of high-performance systems for office buildings in hot and humid climates. High-performance building systems and components were surveyed for buildings in the U.S., which were applicable for office buildings in hot and humid climates. This research developed a calibrated DOE-2.1e simulation model of a prototypical large office building. In addition, a Simplified Geometry DOE-2.1e (SGDOE-2.1e) model, was also developed, which used a simplified geometry to demonstrate the use of a proposed easy-to-use tool. The calibrated DOE-2.1e simulation model and the SGDOE-2.1e were compared and showed a good match with each. The SGDOE-2.1e model was then further modified based on the ASHRAE Standard 90.1-1999 commercial building energy code. A code-compliant (ASHRAE Standard 90.1-1999) SGDOE-2.1e simulation model was then used as a baseline for the evaluation of the high-performance measures. A total of 14 high-performance measures were implemented including the energy savings, while the comfort level was maintained based on the ASHRAE comfort zone. In addition to the 14 high-performance measures, solar thermal and solar PV system analysis were integrated with the SGDOE-2.1e simulation model to further reduce the annual energy use. Finally, specifications of the proposed easy-to-use simulation tool were developed. This tool includes options to choose systems from the 14 high-performance measures and solar systems. The proposed easy-to-use systems selection tool can be used for new building practitioners and existing building owners as well to evaluate the performance of their new buildings compared to the ASHRAE Standard 90.1-1999 code-compliant building, and to assess the feasibility of implementing high-performance measures to their existing buildings in terms of energy and cost savings.

Cho, Sool Yeon

2009-08-01T23:59:59.000Z

164

Methodology to Develop and Test an Easy-To-Use Procedure for the Preliminary Selection of High-Performance Systems for Office Buildings in Hot and Humid Climates  

E-Print Network (OSTI)

A procedure has been developed for the preliminary selection of high-performance systems for office buildings in hot and humid climates. High-performance building systems and components were surveyed for buildings in the U.S., which were applicable for office buildings in hot and humid climates. This research developed a calibrated DOE-2.1e simulation model of a prototypical large office building. In addition, a Simplified Geometry DOE-2.1e (SGDOE-2.1e) model, was also developed, which used a simplified geometry to demonstrate the use of a proposed easy-to-use tool. The calibrated DOE-2.1e simulation model and the SGDOE-2.1e were compared and showed a good match with each. The SGDOE-2.1e model was then further modified based on the ASHRAE Standard 90.1-1999 commercial building energy code. A code-compliant (ASHRAE Standard 90.1-1999) SGDOE-2.1e simulation model was then used as a baseline for the evaluation of the high-performance measures. A total of 14 high-performance measures iv were implemented including the energy savings, while the comfort level was maintained based on the ASHRAE comfort zone. In addition to the 14 high-performance measures, solar thermal and solar PV system analysis were integrated with the SGDOE-2.1e simulation model to further reduce the annual energy use. Finally, specifications of the proposed easy-to-use simulation tool were developed. This tool includes options to choose systems from the 14 high-performance measures and solar systems. The proposed easy-to-use systems selection tool can be used for new building practitioners and existing building owners as well to evaluate the performance of their new buildings compared to the ASHRAE Standard 90.1-1999 code-compliant building, and to assess the feasibility of implementing high-performance measures to their existing buildings in terms of energy and cost savings.

Cho, S.

2009-08-01T23:59:59.000Z

165

Computerized procedures system  

DOE Patents (OSTI)

An online data driven computerized procedures system that guides an operator through a complex process facility's operating procedures. The system monitors plant data, processes the data and then, based upon this processing, presents the status of the current procedure step and/or substep to the operator. The system supports multiple users and a single procedure definition supports several interface formats that can be tailored to the individual user. Layered security controls access privileges and revisions are version controlled. The procedures run on a server that is platform independent of the user workstations that the server interfaces with and the user interface supports diverse procedural views.

Lipner, Melvin H. (Monroeville, PA); Mundy, Roger A. (North Huntingdon, PA); Franusich, Michael D. (Upper St. Clair, PA)

2010-10-12T23:59:59.000Z

166

Human factoring administrative procedures  

Science Conference Proceedings (OSTI)

In nonnuclear business, administrative procedures bring to mind such mundane topics as filing correspondence and scheduling vacation time. In the nuclear industry, on the other hand, administrative procedures play a vital role in assuring the safe operation of a facility. For some time now, industry focus has been on improving technical procedures. Significant efforts are under way to produce technical procedure requires that a validated technical, regulatory, and administrative basis be developed and that the technical process be established for each procedure. Producing usable technical procedures requires that procedure presentation be engineered to the same human factors principles used in control room design. The vital safety role of administrative procedures requires that they be just as sound, just a rigorously formulated, and documented as technical procedures. Procedure programs at the Tennessee Valley Authority and at Boston Edison's Pilgrim Station demonstrate that human factors engineering techniques can be applied effectively to technical procedures. With a few modifications, those same techniques can be used to produce more effective administrative procedures. Efforts are under way at the US Department of Energy Nuclear Weapons Complex and at some utilities (Boston Edison, for instance) to apply human factors engineering to administrative procedures: The techniques being adapted include the following.

Grider, D.A.; Sturdivant, M.H.

1991-11-01T23:59:59.000Z

167

Federal Agency NEPA Procedures  

Energy.gov (U.S. Department of Energy (DOE))

Each Federal agency is required to develop NEPA procedures that supplement the CEQ Regulations. Developed in consultation with CEQ, Federal agency NEPA procedures must meet the standards in the CEQ...

168

TECMIPT Test Operations Procedures (TTOP) For Passive ...  

Science Conference Proceedings (OSTI)

... Conducted disturbances induced by bursts and radio ... on the ingress protection rating (IP) requirement as ... of the initial mean gamma-ray or neutron ...

2013-01-10T23:59:59.000Z

169

ebXML Test Procedures DRAFT Document  

Science Conference Proceedings (OSTI)

... An attack is a specific application of an exploit [After AP-Glossary]. ... Page 7. NIST SP 500-269 January 2008 Page 7 of 13 1.5 Glossary of Terms ...

2013-05-07T23:59:59.000Z

170

Building Technologies Office: Current Test Procedure Waivers  

NLE Websites -- All DOE Office Websites (Extended Search)

2805 72FR71387 121707 Air Conditioners and Heat Pumps, Residential Multi-zone Unitary Small Air Conditioners and Heat Pumps ECR International, Inc. 78FR47681 080613 Heat Pump...

171

EM Policies and Procedures  

NLE Websites -- All DOE Office Websites (Extended Search)

Environmental Management (EM) Desktop References This page offers Environmental Management (EM) operating policies, procedures, standards, workaids, organizational charts, and...

172

Neoadjuvant Radiation Is Associated With Improved Survival in Patients With Resectable Pancreatic Cancer: An Analysis of Data From the Surveillance, Epidemiology, and End Results (SEER) Registry  

Science Conference Proceedings (OSTI)

Purpose: Cancer of the exocrine pancreas is the fifth leading cause of cancer death in the United States. Neoadjuvant chemoradiation has been investigated in several trials as a strategy for downstaging locally advanced disease to resectability. The aim of the present study is to examine the effect of neoadjuvant radiation therapy (RT) vs. other treatments on long-term survival for patients with resectable pancreatic cancer in a large population-based sample group. Methods and Materials: The Surveillance, Epidemiology, and End Results (SEER) registry database (1994-2003) was queried for cases of surgically resected pancreatic cancer. Retrospective analysis was performed. The endpoint of the study was overall survival. Results: Using Kaplan-Meier analysis we found that the median overall survival of patients receiving neoadjuvant RT was 23 months vs. 12 months with no RT and 17 months with adjuvant RT. Using Cox regression and controlling for independent covariates (age, sex, stage, grade, and year of diagnosis), we found that neoadjuvant RT results in significantly higher rates of survival than other treatments (hazard ratio [HR], 0.55; 95% confidence interval, 0.38-0.79; p = 0.001). Specifically comparing adjuvant with neoadjuvant RT, we found a significantly lower HR for death in patients receiving neoadjuvant RT rather than adjuvant RT (HR, 0.63; 95% confidence interval, 0.45-0.90; p = 0.03). Conclusions: This analysis of SEER data showed a survival benefit for the use of neoadjuvant RT over surgery alone or surgery with adjuvant RT in treating pancreatic cancer. Therapeutic strategies that use neoadjuvant RT should be further explored for patients with resectable pancreatic cancer.

Stessin, Alexander M. [Tri-Institutional M.D.-Ph.D. Program, New York, NY (United States); Weill Medical College of Cornell University, New York, NY (United States); Meyer, Joshua E. [New York Presbyterian Hospital, New York, NY (United States); Sherr, David L. [New York Presbyterian Hospital, New York, NY (United States)], E-mail: dls9003@med.cornell.edu

2008-11-15T23:59:59.000Z

173

Retlif Testing Laboratories  

Science Conference Proceedings (OSTI)

... of radio disturbance characteristics of electrical motor-operated and ... and Test Procedures for Airborne Equipment - Section 15 - Magnetic Effect. ...

2014-01-03T23:59:59.000Z

174

University of Waste Procedures  

E-Print Network (OSTI)

University of Maryland Hazardous And Regulated Waste Procedures Manual Revised July 2001 #12;Review II. HAZARDOUS WASTE MANAGEMENT III. BIOLOGICAL, PATHOLOGICAL AND MEDICAL WASTE (BPMW) MANAGEMENT IV. LOW-LEVEL RADIOACTIVE WASTE (LLRW) MANAGEMENT V. EMERGENCY PROCEDURES VI. WASTE MINIMIZATION VII

Rubloff, Gary W.

175

BFRL: HVAC&R - Publications  

Science Conference Proceedings (OSTI)

... were within ±5% of the tested values for six of the mixed systems, and four of the SEER predictions were within ±5% of the tested SEERs. ...

176

NFRC Procedures for Laminates  

NLE Websites -- All DOE Office Websites (Extended Search)

Laminates Laminates Last update: 12/10/2013 07:29 PM NFRC now has a procedure for making laminates in Optics5 and importing those laminate constructions into WINDOW5 to be used in a whole product calculation. The information presented below is provided to help simulators with this process. Feel free to contact us at WINDOWHelp@lbl.gov with questions or comments. NFRC Laminate Procedure Laminate Procedures (approved by NFRC) (PDF file) Approved Interlayer List (IGDB 33.0) (PDF file) NFRC Laminate Procedure Training Powerpoint with Examples (This Powerpoint presentation was used in the NFRC web based training sessions in December 2006 and January 2007) PowerPoint Presentation (PPT file) PowerPoint Presentation (PDF file) Help and Troubleshooting Error Messages The table below contains common warnings and error messages that may appear in Optics5 when calculating a laminate. Some of the messages can be ignored, and some are significant, which is indicated in the table.

177

NSLS Services | Shipping Procedures  

NLE Websites -- All DOE Office Websites (Extended Search)

NSLS Shipping Procedures For shipments arriving at the NSLS from other locations, please ship via Federal Express. If this is not possible, or if you have any questions, please...

178

PROCEDURE FOR PREPARING  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

PROCEDURE FOR PREPARING PROCEDURE FOR PREPARING RECORDS INVENTORY AND DISPOSITION SCHEDULES (RIDS) Revision 1 November 1, 2007 Records Management Division, IM-23 PROCEDURE FOR PREPARING RECORDS INVENTORY AND DISPOSITION SCHEDULES (RIDS) 1. If the records have not yet been inventoried, see "Procedure for Conducting a Records Inventory." An inventory must be completed prior to preparing the RIDS. 2. The Records Inventory and Disposition Schedules (RIDS) should be reviewed and updated at least annually on DOE F 1324.10 and DOE F 1324.9. The RIDS covers all record, administrative and programmatic, as well as non- record material. The RIDS must include: a. Complete and detailed information identifying the organization (s) responsible for the records.

179

Operating Procedures Guideline  

Science Conference Proceedings (OSTI)

The intention of this report is to provide guidance for generating stations’ management and personnel striving for successful methods of developing effective operating procedures. Standard operating procedure management is used in most businesses and industries to assist in the safe and efficient operation of those companies. Effectively managing the program is essential in order to comply with mandatory regulations, maintain the highest possible level of plant integrity, minimize human ...

2012-12-12T23:59:59.000Z

180

Advanced Vehicle Testing Activity: Neighborhood Electric Vehicle...  

NLE Websites -- All DOE Office Websites (Extended Search)

Procedures to someone by E-mail Share Advanced Vehicle Testing Activity: Neighborhood Electric Vehicle Specifications and Test Procedures on Facebook Tweet about Advanced Vehicle...

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Awardee Share Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Awardee Share Procedures Awardee Share Procedures Procedures for Correctly Reporting Awardee Share on the FAADS/FAADS Plus reporting screen in STRIPES To ensure proper reporting by DOE to USASpending.gov, you must enter the awardee share (also known as the cost share, recipient share, and non-federal share) manually on the FAADS/FAADS Plus reporting screen in STRIPES. The FAADS/FAADS Plus file is the financial assistance equivalent of the FPDS-NG data entry for acquisition awards. The awardee share amount is not system generated on the FAADS/FAADS Plus reporting screen like the obligation amount is. The fields on the FAADS/FAADS Plus form which must be entered when reporting a Cost-share Financial Assistance Award are: Field #17 Non-Federal Funding Sign Choose 'Obligation', which refers to a positive amount (sign), or 'Deobligation', which refers to a

182

Radiation Emergency Procedure Demonstrations  

NLE Websites -- All DOE Office Websites (Extended Search)

Managing Radiation Emergencies Managing Radiation Emergencies Procedure Demonstrations Procedure Demonstrations Note: RealPlayer is needed for listening to the narration that accompany these demonstrations. Real Player Dressing To Prevent the Spread of Radioactive Contamination This demonstration shows how your team can dress to prevent the spread of radioactive contamination. Click to begin presentation on dressing to prevent the spread of radioactive contamination. Preparing The Area This demonstration shows basic steps you can take to gather equipment and prepare a room to receive a patient who may be contaminated with radioactive material. Click to begin presentation on preparing a room to receive a radioactive contaminated patient. Removing Contaminated Clothing This demonstration shows the procedure for removing clothing from a patient who may be contaminated with radioactive material.

183

Final test report: demonsration testing in support of the Track 3system waste dislodging, retrieval and conveyance concepts  

SciTech Connect

This report contains the quantitative and qualitative data and information collected during performance of the Track 3 System testing protocol. Information contained herein focuses on the data collected during performance ofthe following Tests Procedures. *Test Procedure-1, Position Management Test Procedure-2, Waste Dislodging, Retrieval, and Conveyance and Decontamination *Test Procedure-3, Dynamic Response Test procedures, Safety Demonstration

Berglin, E.J.

1997-07-24T23:59:59.000Z

184

Advanced Vehicle Testing Activity: Urban Electric Vehicle Specificatio...  

NLE Websites -- All DOE Office Websites (Extended Search)

Test Procedures to someone by E-mail Share Advanced Vehicle Testing Activity: Urban Electric Vehicle Specifications and Test Procedures on Facebook Tweet about Advanced Vehicle...

185

Advanced Vehicle Testing Activity: Hybrid Electric Vehicle Specificati...  

NLE Websites -- All DOE Office Websites (Extended Search)

Test Procedures to someone by E-mail Share Advanced Vehicle Testing Activity: Hybrid Electric Vehicle Specifications and Test Procedures on Facebook Tweet about Advanced Vehicle...

186

Advanced Vehicle Testing Activity: Oil Bypass Filter Specifications...  

NLE Websites -- All DOE Office Websites (Extended Search)

and Test Procedures to someone by E-mail Share Advanced Vehicle Testing Activity: Oil Bypass Filter Specifications and Test Procedures on Facebook Tweet about Advanced...

187

Precipitator Performance Estimation Procedure  

Science Conference Proceedings (OSTI)

Increased availability of data to use with an existing computer model makes it possible for utilities to calculate electrostatic precipitator performance without access to industry databases. This report examines the accuracy of the model and develops procedures to make it a more useful tool for troubleshooting precipitator performance and for selecting the size of a new unit.

1986-12-22T23:59:59.000Z

188

Emergency Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Services Employee Services Safety and Health Emergency Procedures Emergency Procedures Note: This page is pending deletion, please refer to the Safety and health main page...

189

NEV PROCEDURE PUNCH LIST  

NLE Websites -- All DOE Office Websites (Extended Search)

END OF LIFE TEST SEQUENCE Revision 0 September 1, 2006 Prepared by Electric Transportation Applications Prepared by: Date: Roberta Brayer...

190

NEV PROCEDURE PUNCH LIST  

NLE Websites -- All DOE Office Websites (Extended Search)

BASELINE TEST SEQUENCE Revision 1 September 1, 2006 Prepared by Electric Transportation Applications Prepared by: Date: Roberta Brayer...

191

NEV PROCEDURE PUNCH LIST  

NLE Websites -- All DOE Office Websites (Extended Search)

NEVAmerica TEST SEQUENCE Revision 2 Effective February 1, 2008 Prepared by Electric Transportation Applications Prepared by: Date: Nick...

192

TRANSPARENCY RECYCLING PROGRAM PROCEDURES  

NLE Websites -- All DOE Office Websites (Extended Search)

TRANSPARENCY RECYCLING Don't throw out your used overhead transparencies! RECYCLE them for REUSE. It's Easy! Follow these simple procedures: 1.) COLLECT used transparencies to be recycled. 2.) SEPARATE the transparencies from ringed binders, plastic or paper folders, envelopes, and/or files. 3.) PLACE the transparencies (only) into an intra-laboratory mail envelope. 4.) SEND the envelope to: Terri Schneider, Building 201, 1D-10. Terri will prepare a

193

DOE Reasonable Accommodation Procedures  

Energy.gov (U.S. Department of Energy (DOE))

Pursuant to Executive Order 13164, the Department of Energy (hereinafter referred to as the “department”), is charged with establishing written procedures for the facilitation of reasonable accommodation for: (1) individuals with disabilities in the application process for employment with the Department; (2) Department employees with disabilities to perform the essential functions of a position; and (3) Department employees with disabilities to enjoy benefits and privileges of employment equal to those enjoyed by employees without disabilities.

194

CMS System Security Plan Procedure  

Science Conference Proceedings (OSTI)

... TASK 5: SYSTEM DECOMMISSION. ... BPSSM Business Partners Systems Security Manual. ... of Information Technology, Policy, Procedures, & Audits. ...

2009-06-30T23:59:59.000Z

195

Comparisons of field performance to closed-door test T ABLE 1 ratings indicate the laboratory procedure is a valid indica-Design Options to Improve the Energy Efficiency of a  

E-Print Network (OSTI)

#12;#12;Comparisons of field performance to closed-door test T ABLE 1 ratings indicate commercially manufactured refrigerators were u~ as laboratory test beds, a testing sequence of ..as PHASE I cabinets with an optimized Option 2 Evaporator/condenser size, surface r~frige~tion circuit or cvcle were

Oak Ridge National Laboratory

196

SANS Training Voucher Program Registration Procedures | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

SANS Training Voucher Program Registration Procedures SANS Training Voucher Program Registration Procedures SANS Training Voucher Program Registration Procedures For Federal...

197

Records Management Exit Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exit Procedures For Departing Federal and contractor Employees PRESERVATION OF FEDERAL RECORDS The Federal Records Act requires the Department of Energy (DOE) Records Officer to remind departing Federal and contractor employees that Federal records may not be removed from Government custody nor may they be destroyed except in accordance with a records disposition schedule that has been approved by the Archivist of the United States. The creation of adequate documentation and the preservation of Federal records are required by law and regulation (contained in 36 CFR Chapter XII). As Federal and contractor employees, you have Federal record-keeping responsibilities that are regulated by the National Archives and Records Administration (NARA) to ensure the retention and

198

Advanced Vehicle Testing Activity: Full-Size Electric Vehicle...  

NLE Websites -- All DOE Office Websites (Extended Search)

Procedures to someone by E-mail Share Advanced Vehicle Testing Activity: Full-Size Electric Vehicle Specifications and Test Procedures on Facebook Tweet about Advanced Vehicle...

199

Advanced Vehicle Testing Activity: Plug-in Hybrid Electric Vehicle...  

NLE Websites -- All DOE Office Websites (Extended Search)

Procedures to someone by E-mail Share Advanced Vehicle Testing Activity: Plug-in Hybrid Electric Vehicle Specifications and Test Procedures on Facebook Tweet about Advanced...

200

Presidential Permits - Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Permits - Procedures Presidential Permits - Procedures Electricity Advisory Committee Technology Development Electricity Policy Coordination and Implementation Transmission...

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

NIST Assists with Testing Crash Avoidance System  

Science Conference Proceedings (OSTI)

NIST Assists with Testing Crash Avoidance System. ... of Transportation (DOT) by developing tests for a ... has designed preliminary test procedures that ...

2012-12-13T23:59:59.000Z

202

Phase 2 Development of Procedure Usability Measurement Process (PUMP) Method  

Science Conference Proceedings (OSTI)

Usability problems with plant procedures contribute to a large percentage of errors committed by plant technicians, factor into more than half of all licensee event reports (LERs), and cost an average plant as much as $1M annually. This report outlines in detail EPRI's Procedure Usability Measurement Process (PUMP) method -- a package of standardized testing instruments for measuring the usability of plant procedures -- and describes its successful application at two plants.

1998-07-31T23:59:59.000Z

203

Overview Paper on In-Situ Testing -Singapore Workshop, Nov. 29-Dec. 01,2006 -P.W. Mayne -Page 1 1 INTRODUCTION  

E-Print Network (OSTI)

........................................................................................256 Sampler and Other Test Apparatus Materials ...............................................................................278 Manual Sampling Procedures..............................................................................................313 Sediment Sampling Procedures

Mayne, Paul W.

204

Procedures for sprinkler anchor installation on surfaces with fireproofing materials  

SciTech Connect

Procedures were developed for limiting the release of fibers from fireproofing material during sprinkler hanger anchor installation on steel deck/concrete floor slab surfaces. These procedures were needed by the General Services Administration (GSA) for installation of sprinkler systems in buildings having fireproofing containing asbestos. A prototype floor slab having spray-on friable mineral wool fireproofing was used in laboratory tests. The mineral-wool fireproofing was used as a model system for fireproofing containing asbestos. The various combinations of mechanical anchoring procedures (use of drills or powder-actuated gun) and encapsulation procedures tested limited the fiber release to a range of values of 0.000 to 0.055 f/cc (fibers per cubic centimeter) as compared to a range of values of 0.26 to 0.82 f/cc for procedures without encapsulation. Encapsulation was shown to be effective as evidenced by much higher levels of fiber release during testing without encapsulation. Because there is no known correlation between the release of mineral-wool fibers and asbestos fibers, it was recommended that the procedures developed be evaluated by GSA in buildings having fireproofing containing asbestos. An air-sampling protocol was developed for use by GSA in evaluating the procedures in the field. Subsequently field tests were conducted by GSA. The laboratory and field studies provided GSA with an effective procedure, measurement method, and decision tool for installing sprinkler hanger anchors in steel deck/concrete floor slabs having fireproofing materials.

Mathey, R.G.; Knab, L.I.; Gross, J.L.; Small, J.A.

1988-02-01T23:59:59.000Z

205

WSDOT Test Method T 127 Preparation of Leachate Sample for Testing Toxicity of HECP Effluents 1. Scope This test method outlines the procedure for collecting leachate from a HECP sample. 2. References 2.1 EPA-821-R-02-012 Methods for Measuring Acute Toxic  

E-Print Network (OSTI)

3.1 Lay cheesecloth over clean topsoil 3.2 Apply the HECP to the cheesecloth at the following coverage: 3.2.1 HECP Long-Term or Moderate-Term Mulch 3,500 lbs per acre in two lifts with no more than 2000 # per acre in any one lift. 3.2.2 HECP Short-Term Mulch 2000 # per acre minimum, or manufacturer’s recommended rate may be used. 3.3 Allow material to cure for 48 hours 3.4 Pull cheesecloth up with mat of HECP, brush off any soil 3.5 Cut HECP into squares and provide 1.02 pounds of HECP to the laboratory. 4. Preparation of the Leachate (done by the laboratory) 4.1 Allow hydromulch product to soak in water for one hour 4.2 Remove hydromulch sheet from water 4.3 Filter water through a 60 micron filter – water may be pre-filtered through a 35 mesh and then a 120 mesh before using the 230 mesh/63 micron filter. Note: Leachate not immediately used for testing should be stored at 4 ° C in the dark until

unknown authors

2012-01-01T23:59:59.000Z

206

Department of Energy Technical Standards Procedures | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Department of Energy Technical Standards Procedures Department of Energy Technical Standards Procedures DOE Technical Standards Program The following procedures should be used to...

207

Procedure for Planning and Conducting  

NLE Websites -- All DOE Office Websites (Extended Search)

Lift Plan Procedure Lift Plan Procedure Stanford Synchrotron Radiation Laboratory Lead Author __________________________________ Date 07/13/2005___________ David A. Ernst Mechanical Service Group Approvals: __________________ Date _____________________ Matt Padilla SSRL Safety Officer __________________ Date _____________________ Robert Hettel Accelerator System Department Head __________________ Date _____________________ Piero Pianetta Beam Line System Department Head Hoist and Rigging Panel Member _______________________________________ Date ______________________

208

Specific test and evaluation plan  

SciTech Connect

The purpose of this Specific Test and Evaluation Plan (STEP) is to provide a detailed written plan for the systematic testing of modifications made to the 241-AX-B Valve Pit by the W-314 Project. The STEP develops the outline for test procedures that verify the system`s performance to the established Project design criteria. The STEP is a lower tier document based on the W-314 Test and Evaluation Plan (TEP). Testing includes Validations and Verifications (e.g., Commercial Grade Item Dedication activities), Factory Acceptance Tests (FATs), installation tests and inspections, Construction Acceptance Tests (CATs), Acceptance Test Procedures (ATPs), Pre-Operational Test Procedures (POTPs), and Operational Test Procedures (OTPs). It should be noted that POTPs are not required for testing of the transfer line addition. The STEP will be utilized in conjunction with the TEP for verification and validation.

Hays, W.H.

1998-03-20T23:59:59.000Z

209

Model of Procedure Usage – Results from a Qualitative Study to Inform Design of Computer-Based Procedures  

SciTech Connect

The nuclear industry is constantly trying to find ways to decrease the human error rate, especially the human errors associated with procedure use. As a step toward the goal of improving procedure use performance, researchers, together with the nuclear industry, have been looking at replacing the current paper-based procedures with computer-based procedure systems. The concept of computer-based procedures is not new by any means; however most research has focused on procedures used in the main control room. Procedures reviewed in these efforts are mainly emergency operating procedures and normal operating procedures. Based on lessons learned for these previous efforts we are now exploring a more unknown application for computer based procedures - field procedures, i.e. procedures used by nuclear equipment operators and maintenance technicians. The Idaho National Laboratory, the Institute for Energy Technology, and participants from the U.S. commercial nuclear industry are collaborating in an applied research effort with the objective of developing requirements and specifications for a computer-based procedure system to be used by field operators. The goal is to identify the types of human errors that can be mitigated by using computer-based procedures and how to best design the computer-based procedures to do this. The underlying philosophy in the research effort is “Stop – Start – Continue”, i.e. what features from the use of paper-based procedures should we not incorporate (Stop), what should we keep (Continue), and what new features or work processes should be added (Start). One step in identifying the Stop – Start – Continue was to conduct a baseline study where affordances related to the current usage of paper-based procedures were identified. The purpose of the study was to develop a model of paper based procedure use which will help to identify desirable features for computer based procedure prototypes. Affordances such as note taking, markups, sharing procedures between fellow coworkers, the use of multiple procedures at once, etc. were considered. The model describes which affordances associated with paper based procedures should be transferred to computer-based procedures as well as what features should not be incorporated. The model also provides a means to identify what new features not present in paper based procedures need to be added to the computer-based procedures to further enhance performance. The next step is to use the requirements and specifications to develop concepts and prototypes of computer-based procedures. User tests and other data collection efforts will be conducted to ensure that the real issues with field procedures and their usage are being addressed and solved in the best manner possible. This paper describes the baseline study, the construction of the model of procedure use, and the requirements and specifications for computer-based procedures that were developed based on the model. It also addresses how the model and the insights gained from it were used to develop concepts and prototypes for computer based procedures.

Johanna H Oxstrand; Katya L Le Blanc

2012-07-01T23:59:59.000Z

210

Records Management Exit Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

leave. Records Management Exit Procedures More Documents & Publications Records Management Exit Procedures Operational Plan and Desktop Reference for the Veterans...

211

External > Programs > Environmental Management > Policies & Procedures  

NLE Websites -- All DOE Office Websites (Extended Search)

Policies & Procedures This website offers Environmental Management (EM) operating policies, procedures, standards, workaids, organizational charts, and other pertinent documents...

212

The Fallout between Procedure and Practice  

E-Print Network (OSTI)

OF CALIFORNIA SANTA CRUZ The Fallout between procedure andAurora Olmos-Gallo The Fallout Between Procedure and

Olmos-Gallo, Aurora Maria

2013-01-01T23:59:59.000Z

213

Slimhole Handbook- Procedures and Recommendations for Slimhole Drilling and  

Open Energy Info (EERE)

Slimhole Handbook- Procedures and Recommendations for Slimhole Drilling and Slimhole Handbook- Procedures and Recommendations for Slimhole Drilling and Testing in Geothermal Exploration Jump to: navigation, search OpenEI Reference LibraryAdd to library Report: Slimhole Handbook- Procedures and Recommendations for Slimhole Drilling and Testing in Geothermal Exploration Abstract No abstract prepared. Authors Jim Combs, John T. Finger, Colin Goranson, Charles E. Hockox Jr., Ronald D. Jacobsen and Gene Polik Organization Sandia National Laboratories Published Geothermal Technologies Legacy Collection, 1999 Report Number SAND99-1976 DOI Not Provided Check for DOI availability: http://crossref.org Online Internet link for Slimhole Handbook- Procedures and Recommendations for Slimhole Drilling and Testing in Geothermal Exploration Citation

214

NFRC Procedures for Applied Films  

NLE Websites -- All DOE Office Websites (Extended Search)

Applied Films Applied Films Last update: 12/10/2013 07:29 PM NFRC now has a procedure for adding applied films to substrates in Optics5 and importing those applied film constructions into WINDOW5 to be used in a whole product calculation. The information presented below is provided to help simulators with this process. Feel free to contact us at WINDOWHelp@lbl.gov with questions or comments. NFRC Applied Film Procedure Applied Film Procedures (approved by NFRC) (PDF file) Approved Applied Film List (IGDB 33.0) (PDF file) NFRC Laminate Procedure Training Powerpoint with Examples (This Powerpoint presentation was used in the NFRC web based training sessions in December 2006 and January 2007) PowerPoint Presentation (PPT file) PowerPoint Presentation (PDF file) Help and Troubleshooting

215

The Design Procedure Language Manual  

E-Print Network (OSTI)

This manual describes the Design Procedure Language (DPL) for LSI design. DPL creates and maintains a representation of a design in a hierarchically organized, object-oriented LISP data-base. Designing in DPL involves ...

Batali, John

1980-09-01T23:59:59.000Z

216

IES Calibration and Mapping Procedures  

Science Conference Proceedings (OSTI)

The procedures used in the Synoptic Ocean Prediction experiment for calibration of inverted echo sounder (IES) travel time ? data have led to substantially improved accuracy. In previous work, ? was converted to main thermocline depth ZT using ...

Karen L. Tracey; Stephan D. Howden; D. Randolph Watts

1997-12-01T23:59:59.000Z

217

Solar Thermal Test Facility experiment manual  

DOE Green Energy (OSTI)

Information is provided on administrative procedures, capabilities, and requirements of experimenters using the Solar Thermal Test Facility. (MHR)

Darsey, D. M.; Holmes, J. T.; Seamons, L. O.; Kuehl, D. J.; Davis, D. B.; Stomp, J. M.; Matthews, L. K.; Otts, J. V.

1977-10-01T23:59:59.000Z

218

Test Automation Test Automation  

E-Print Network (OSTI)

Test Automation Test Automation Mohammad Mousavi Eindhoven University of Technology, The Netherlands Software Testing 2013 Mousavi: Test Automation #12;Test Automation Outline Test Automation Mousavi: Test Automation #12;Test Automation Why? Challenges of Manual Testing Test-case design: Choosing inputs

Mousavi, Mohammad

219

Procedure  

Science Conference Proceedings (OSTI)

... The recording drives used in this study include the Sony DRU-510A, 700A , 800A, Pioneer DVR-A09 , Plextor PX-716SA and NEC ND -2510A . ...

220

First semiannual report: Rocky Flats Small Wind Systems Test Center activities. Volume I. Description of the National Small Wind Systems Test Center  

DOE Green Energy (OSTI)

Information is presented concerning the Rocky Flats wind turbine test site; the philosophy of testing at Rocky Flats; test procedure development; atmospheric SWECS testing; SWECS component testing; data collection, handling, and analysis; reporting procedures; and future plans.

None

1978-09-28T23:59:59.000Z

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Laboratory Performance Testing of Residential Window Air Conditioners  

SciTech Connect

Window air conditioners are the dominant cooling product for residences, in terms of annual unit sales. They are inexpensive, portable and can be installed by the owner. For this reason, they are an attractive solution for supplemental cooling, for retrofitting air conditioning into a home which lacks ductwork, and for renters. Window air conditioners for sale in the United States are required to meet very modest minimum efficiency standards. Four window air conditioners' performance were tested in the Advanced HVAC Systems Laboratory on NREL's campus in Golden, CO. In order to separate and study the refrigerant system's performance, the unit's internal leakage pathways, the unit's fanforced ventilation, and the leakage around the unit resulting from installation in a window, a series of tests were devised that focused on each aspect of the unit's performance. These tests were designed to develop a detailed performance map to determine whole-house performance in different climates. Even though the test regimen deviated thoroughly from the industry-standard ratings test, the results permit simple calculation of an estimated rating for both capacity and efficiency that would result from a standard ratings test. Using this calculation method, it was found that the three new air conditioners' measured performance was consistent with their ratings. This method also permits calculation of equivalent SEER for the test articles. Performance datasets were developed across a broad range of indoor and outdoor operating conditions, and used them to generate performance maps.

Winkler, J.; Booten, C.; Christensen, D.; Tomerlin, J.

2013-03-01T23:59:59.000Z

222

Management of Hazardous Waste A Policy and Procedures Manual  

E-Print Network (OSTI)

the Toxicity Characteristic Leaching Procedure Test, or "TCLP") meets or exceeds these regulatory levels. For liquids, the TCLP result is approximately the same as the actual mass concentration. For solid state materials that contain any of the listed contaminants, the TCLP test needs to be conducted to determine

Cooley, Lynn

223

Photovoltaic module energy rating procedure. Final subcontract report  

DOE Green Energy (OSTI)

This document describes testing and computation procedures used to generate a photovoltaic Module Energy Rating (MER). The MER consists of 10 estimates of the amount of energy a single module of a particular type (make and model) will produce in one day. Module energy values are calculated for each of five different sets of weather conditions (defined by location and date) and two load types. Because reproduction of these exact testing conditions in the field or laboratory is not feasible, limited testing and modeling procedures and assumptions are specified.

Whitaker, C.M.; Newmiller, J.D. [Endecon Engineering (United States)

1998-01-01T23:59:59.000Z

224

Advanced Vehicle Testing Activity: Hydrogen Internal Combustion...  

NLE Websites -- All DOE Office Websites (Extended Search)

to someone by E-mail Share Advanced Vehicle Testing Activity: Hydrogen Internal Combustion Engine Vehicle Specifications and Test Procedures on Facebook Tweet about Advanced...

225

Improving Clinical Laboratory Testing through Harmonization ...  

Science Conference Proceedings (OSTI)

... involvement in harmonizing this category of clinical laboratory testing procedures. ... patients at risk from non-standardized laboratory test results and ...

2013-05-21T23:59:59.000Z

226

Federal Agency NEPA Implementing Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Agency NEPA Implementing Procedures Agency NEPA Implementing Procedures Note: Some Departments' agencies have their own NEPA implementing procedures. To access Department-wide NEPA implementing procedures, click on the name of the Federal Department. To access NEPA implementing procedures for Department's agencies, click on the provided links. Department/ Agency: Division: Link: Department of Agriculture Agricultural Research Service http://www.ecfr.gov/cgi- in/text- idx?c=ecfr&SID=47c103e07fd64e933c7f74c 4b3c4ac9a&rgn=div5&view=text&node=7:6. 1 2 1 8&id 7 Animal and Plant Health Inspection Service http://www.ecfr.gov/cgi-bin/text- idx?c=ecfr&SID=47c103e07fd64e933c7f74c 4b3c4ac9a&rgn=div5&view=text&node=7:5. 1.1.1.21&idno=7 Farm Service Agency http://www.ecfr.gov/cgi-bin/text-

227

Surveillance Guide - OPS 9.16 Procedure Content and Use  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

PROCEDURE CONTENT AND USE PROCEDURE CONTENT AND USE 1.0 Objective The objective of this surveillance is to evaluate the effectiveness of the contractor's program for development and use of procedures. The Facility Representative reviews selected operating, surveillance or testing, and maintenance procedures and observes use of the procedures in the facility. This surveillance provides the basis for evaluating contractor performance and for establishing compliance with specific DOE requirements. 2.0 References 2.1 DOE 5480.19, Conduct of Operations Requirements for DOE Facilities 3.0 Requirements Implemented This surveillance is conducted to implement requirements of the Functions, Requirements and Authorities Manual, Section 20, Operations, FRAM #s 4253, 4258, and 4261. These requirements are

228

DOE Technical Standards Program: Procedures  

NLE Websites -- All DOE Office Websites (Extended Search)

Department of Energy Technical Standards Procedures Department of Energy Technical Standards Procedures Office of Nuclear Safety The following procedures should be used to write, revise, or maintain a DOE technical standard. They are also used to convert a DOE technical standard to a non-government standard or to form a topical committee. Table of Contents (TSPP-00) Program Overview and Responsibilities (TSPP-01) Initiating DOE Technical Standards (TSPP-02) Use of Voluntary Consensus Standards and Interaction with Standards Development Organizations (TSPP-03) Developing DOE Technical Standard (TSPP-04) Coordination of Technical Standards (TSPP-05) - Draft In Concurrence Resolution - TSPP-06-2009 is the currently approved TSPP that addresses coordination of DOE Technical Standards. Approving and Issuing DOE Technical Standards (TSPP-06)

229

Radiation control standards and procedures  

SciTech Connect

This manual contains the Radiation Control Standards'' and Radiation Control Procedures'' at Hanford Operations which have been established to provide the necessary control radiation exposures within Irradiation Processing Department. Provision is also made for including, in the form of Bulletins'', other radiological information of general interest to IPD personnel. The purpose of the standards is to establish firm radiological limits within which the Irradiation Processing Department will operate, and to outline our radiation control program in sufficient detail to insure uniform and consistent application throughout all IPD facilities. Radiation Control Procedures are intended to prescribe the best method of accomplishing an objective within the limitations of the Radiation Control Standards. A procedure may be changed at any time provided the suggested changes is generally agreeable to management involved, and is consistent with department policies and the Radiation Control Standards.

1956-12-14T23:59:59.000Z

230

Workshop on Test Procedures for Materials for Hydrogen ...  

Science Conference Proceedings (OSTI)

... Boulder, CO 80302-5821 (303) 442-5688. Gunbarrel Guest House 6901 Lookout Rd. ... Quality Inn & Suites 2020 Arapahoe Ave. ...

231

Development of Test Methods and Rating Procedures for ...  

Science Conference Proceedings (OSTI)

... membrane fuel cells (PEMFC) are the predominant type of fuel cell being considered for residential use, but solid oxide fuel cells (SOFC) are also ...

2002-03-01T23:59:59.000Z

232

Standard-C hydrogen monitoring system acceptance test procedure  

DOE Green Energy (OSTI)

The primary function of the standard-C hydrogen monitoring system (SHMS) is to monitor specifically for hydrogen in the waste tank atmosphere which may also contain (but not be limited to) unknown quantities of air, nitrous oxide, ammonia, water vapor, carbon dioxide, carbon monoxide, and other gaseous constituents. The SHMS will consist of hydrogen specific monitors, a grab sampler to collect samples for laboratory analysis, a gas chromatograph, and the gas sample collection system necessary to support the operation of the instrumentation. This system will be located in a cabinet placed at the tank of interest. The purpose of this document is to demonstrate that the SHMS is constructed as intended by design.

Schneider, T.C.

1994-09-02T23:59:59.000Z

233

Standard-E hydrogen monitoring system shop acceptance test procedure  

DOE Green Energy (OSTI)

The purpose of this report is to document that the Standard-E Hydrogen Monitoring Systems (SHMS-E), fabricated by Mid-Columbia Engineering (MCE) for installation on the Waste Tank Farms in the Hanford 200 Areas, are constructed as intended by the design. The ATP performance will verify proper system fabrication.

Schneider, T.C.

1997-10-02T23:59:59.000Z

234

Solderability test system  

DOE Patents (OSTI)

A new test method to quantify capillary flow solderability on a printed wiring board surface finish. The test is based on solder flow from a pad onto narrow strips or lines. A test procedure and video image analysis technique were developed for conducting the test and evaluating the data. Feasibility tests revealed that the wetted distance was sensitive to the ratio of pad radius to line width (l/r), solder volume, and flux predry time.

Yost, Fred (Cedar Crest, NM); Hosking, Floyd M. (Albuquerque, NM); Jellison, James L. (Albuquerque, NM); Short, Bruce (Beverly, MA); Giversen, Terri (Beverly, MA); Reed, Jimmy R. (Austin, TX)

1998-01-01T23:59:59.000Z

235

Solderability test system  

DOE Patents (OSTI)

A new test method to quantify capillary flow solderability on a printed wiring board surface finish. The test is based on solder flow from a pad onto narrow strips or lines. A test procedure and video image analysis technique were developed for conducting the test and evaluating the data. Feasibility tests revealed that the wetted distance was sensitive to the ratio of pad radius to line width (l/r), solder volume, and flux predry time. 11 figs.

Yost, F.; Hosking, F.M.; Jellison, J.L.; Short, B.; Giversen, T.; Reed, J.R.

1998-10-27T23:59:59.000Z

236

Handbook of Academic Requirements & Procedures  

E-Print Network (OSTI)

Handbook of Academic Requirements & Procedures for the Chemistry Graduate Program PLEASE NOTE: This version of the Handbook must be used by students who start during or after the Spring 2012 semester is a central activity. 1.2 Purpose and Content of the Handbook. A detailed account of the academic requirements

Kounaves, Samuel P.

237

Handbook of Academic Requirements & Procedures  

E-Print Network (OSTI)

Handbook of Academic Requirements & Procedures for the Chemistry Graduate Program PLEASE NOTE: This version of the Handbook can be used by students who started during or before the Fall 2011 semester activity. 1.2 Purpose and Content of the Handbook. A detailed account of the academic requirements

Kounaves, Samuel P.

238

BRITISH COLUMBIA Gully Assessment Procedure  

E-Print Network (OSTI)

strategies and #12;Gully Assessment Procedure Guidebook iv prescriptions designed to accommodate resource).........................................................15 Section 5 Fan Destabilization Potential OPR 37 (1)(c), WLFMR 64 (2)(a......................................30 3. Design and construction of roads across gully systems: when to consult a qualified registered

239

FLORIDA STATE UNIVERSITY Procedures for  

E-Print Network (OSTI)

will be required that describes the purpose for the costs and the direct benefit to the proposed project's scopeFLORIDA STATE UNIVERSITY Procedures for Participant Support Costs Effective: May 15, 2006 Budgeting for Participant Costs Whenever Participant Support Costs are proposed in a budget, a detailed justification

Weston, Ken

240

Past DOE Technical Standards Program Procedures | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Information Center DOE Technical Standards Program DOE Technical Standards Procedures Past DOE Technical Standards Program Procedures Past DOE Technical Standards Program...

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

DNS Policies & Procedures | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

DNS Policies & Procedures DNS Policies & Procedures DNS Policy Every Federal agency must use only .gov, .mil, or Fed.us domains unless the agency head explicitly determines another...

242

EVMS Surveillance Standard Operating Procedure (ESSOP) | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Reporting System (PARS II) INDEPENDENT COST REVIEW (ICR) and INDEPENDENT COST ESTIMATE (ICE) Standard Operating Procedures ICR-ICE Standard Operating Procedures (Update Sept 2013)...

243

Procedures and Instructions | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Access Training Records Management Processes Procedure for Conducting a Records Inventory (PDF) Procedure for Preparing a Records Inventory and Disposition Schedule (RIDS)...

244

External Independent Review (EIR) Standard Operating Procedure...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Standard Operating Procedure (SOP) External Independent Review (EIR) Standard Operating Procedure (SOP) EIR SOP.pdf More Documents & Publications ICR-ICE Standard Operating...

245

Fire Tests of Amtrak Passenger Rail Vehicle Interiors  

Science Conference Proceedings (OSTI)

Page 1. Fire Tests of Amtrak Passenger ... Table 11. Test Procedures and Evaluation Criteria for Small- Scale Testing of Amtrak Furnishings..... ...

2004-04-02T23:59:59.000Z

246

Advanced Vehicle Testing Activity: U.S. Postal Service  

NLE Websites -- All DOE Office Websites (Extended Search)

Storage Testing Hydrogen Internal Combustion Engine Vehicles Full-Size Electric Vehicles Basics Specifications & Test Procedures Testing Reports Special Projects Neighborhood...

247

Surface Environmental Surveillance Procedures Manual  

SciTech Connect

Environmental surveillance data are used in assessing the impact of current and past site operations on human health and the environment, demonstrating compliance with applicable local, state, and federal environmental regulations, and verifying the adequacy of containment and effluent controls. SESP sampling schedules are reviewed, revised, and published each calendar year in the Hanford Site Environmental Surveillance Master Sampling Schedule. Environmental samples are collected by SESP staff in accordance with the approved sample collection procedures documented in this manual.

RW Hanf; TM Poston

2000-09-20T23:59:59.000Z

248

JOINT OFFICER MANAGEMENT PROGRAM PROCEDURES  

E-Print Network (OSTI)

implementation of the DOD Joint Officer Management (JOM) and Joint Qualification System (JQS) per references a through c. Reference a delegates the authority to the Chairman of the Joint Chiefs of Staff to establish and publish regulations and procedures to ensure compliance with the statutory and Department policy standards for DOD’s JOM program. 2. Cancellation. CJCSI 1330.02C, 24 February 2006, is cancelled. Required review of promotion selection board results policy guidance has been incorporated in this instruction.

References See Enclosure N; Responsibilities For

2008-01-01T23:59:59.000Z

249

CSP Policies & Procedures Process for Grade Appeals  

E-Print Network (OSTI)

CSP Policies & Procedures Process for Grade Appeals Grade Appeals ­ Generally speaking, once grades

Leistikow, Bruce N.

250

Microgrid Testing  

Science Conference Proceedings (OSTI)

With the publication of IEEE 1574.4 Guide for Design, Operation, and Integration of Distributed Resource Island Systems with Electric Power Systems, there is an increasing amount of attention on not only the design and operations of microgrids, but also on the proper operation and testing of these systems. This standard provides alternative approaches and good practices for the design, operation, and integration of microgrids. This includes the ability to separate from and reconnect to part of the utility grid while providing power to the islanded power system. This presentation addresses the industry need to develop standardized testing and evaluation procedures for microgrids in order to assure quality operation in the grid connected and islanded modes of operation.

Shirazi, M.; Kroposki, B.

2012-01-01T23:59:59.000Z

251

Society of Nuclear Medicine Procedure  

E-Print Network (OSTI)

The purpose of this guideline is to assist nuclear medicine practitioners in recommending, performing, interpreting, and reporting the results of lung scintigraphy for pulmonary embolism. II. Background Information and Definitions A. Aerosol Ventilation Scintigraphy A diagnostic imaging test that records the bronchopulmonary distribution of an inhaled radioactive aerosol within the lungs. B. Gas Ventilation Scintigraphy A diagnostic imaging test that records the pulmonary distribution of a radioactive gas during breathing maneuvers. C. Pulmonary Perfusion Scintigraphy A diagnostic imaging test that records the distribution

Guideline For Lung Scintigraphy

2004-01-01T23:59:59.000Z

252

Slimhole Handbook- Procedures And Recommendations For Slimhole Drilling And  

Open Energy Info (EERE)

Slimhole Handbook- Procedures And Recommendations For Slimhole Drilling And Slimhole Handbook- Procedures And Recommendations For Slimhole Drilling And Testing In Geothermal Exploration Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Report: Slimhole Handbook- Procedures And Recommendations For Slimhole Drilling And Testing In Geothermal Exploration Details Activities (27) Areas (8) Regions (0) Abstract: No abstract prepared. Author(s): Jim Combs, John T. Finger, Colin Goranson, Charles E. Hockox Jr., Ronald D. Jacobsen, Gene Polik Published: Geothermal Technologies Legacy Collection, 1999 Document Number: Unavailable DOI: Unavailable Source: View Original Report Acoustic Logs At Newberry Caldera Area (Combs, Et Al., 1999) Acoustic Logs At Steamboat Springs Area (Combs, Et Al., 1999) Core Analysis At Fort Bliss Area (Combs, Et Al., 1999)

253

International Energy Agency design tool evaluation procedure  

Science Conference Proceedings (OSTI)

Detailed state-of-the-art building energy simulation models from nations participating in International Energy Agency (IEA) Task VIII are used to develop a quantitative procedure to evaluate more simplified design tools. Simulations are performed with the detailed models on a series of cases that progress systematically from the extremely simple to the relatively realistic. Output values for the cases, such as annual loads, annual maximum and minimum temperatures, and peak loads, are used to set target ranges with which the results from more simplified design tools can be compared. The more realistic cases, although geometrically simple, test the ability of the design tools to model such combined effects as thermal mass, direct gain windows, overhangs, internally generated heat, and dead-band and set-back thermostat control strategies. 5 refs., 9 figs., 4 tabs.

Judkoff, R.; Barakat, S.; Bloomfield, D.; Poel, B.; Stricker, R.; van Haaster, P.; Wortman, D.

1988-07-01T23:59:59.000Z

254

The Fundamentals of Forensic Investigation Procedures Guidebook  

Science Conference Proceedings (OSTI)

No reference or guideline for the practice of or procedure for analyzing equipment failures and accidents involving electric utility distribution systems has been available until publication of "The Fundamentals of Forensic Investigation Procedures Guidebook."

2003-03-18T23:59:59.000Z

255

ECN Pressure Test  

SciTech Connect

This note describes: the rationale for the test pressure of the inner ECN cryostat vessel, the equipment to be used in this test, the test procedure, the status of the vessel prior to the test, the actual test results, and a schematic diagram of the testing set up and the pressure testing permit. The test, performed in the evening of July 17, 1991, was a major success. Based on a neglible pressure drop indicated on the pressure gages (1/4 psi), the vessel appeared to be structurally sound throughout the duration of the test (approx. 1.5 hrs.). No pressure increases were observed on the indicators looking at the beam tube bellows volumes. There was no indication of bubbles form the soap test on the welds and most of the fittings that were checked. There were some slight deviations in the actual procedure used. The UO filter was removed after the vessel had bled down to about 18 psig in order to speed up that aspect of the test. The rationale was that the higher velocity gas had already passed through at the higher pressures and there was no visible traces of the black uo particles. The rate of 4 psi/10 minutes seemed incredibly slow and often that time was reduced to just over half that rate. The testing personnel was allowed to stay in the pit throughout the duration of the test; this was a slight relaxation of the rules.

Dixon, K.; /Fermilab

1991-07-18T23:59:59.000Z

256

Specific test and evaluation plan  

SciTech Connect

The purpose of this Specific Test and Evaluation Plan (STEP) is to provide a detailed written plan for the systematic testing of modifications made to the 241-AN-A Valve Pit by the W-314 Project. The STEP develops the outline for test procedures that verify the system`s performance to the established Project design criteria. The STEP is a ``lower tier`` document based on the W-314 Test and Evaluation Plan (TEP) This STEP encompasses all testing activities required to demonstrate compliance to the project design criteria as it relates to the modifications of the AN-A valve pit. The Project Design Specifications (PDS) identify the specific testing activities required for the Project. Testing includes Validations and Verifications (e.g., Commercial Grade Item Dedication activities), Factory Acceptance Tests (FATs), installation tests and inspections, Construction Acceptance Tests (CATs), Acceptance Test Procedures (ATPs), Pre-Operational Test Procedures (POTPs), and Operational Test Procedures (OTPs). It should be noted that POTPs are not required for testing of the modifications to the 241-AN-A Valve Pit. The STEP will be utilized in conjunction with the TEP for verification and validation.

Hays, W.H.

1997-12-09T23:59:59.000Z

257

Detailed Test Information  

NLE Websites -- All DOE Office Websites (Extended Search)

Detailed Test Information Detailed Test Information EPA tests vehicles by running them through a series of driving routines, also called cycles or schedules, that specify vehicle speed for each point in time during the laboratory tests. For 2007 and earlier model year vehicles, only the city and highway schedules were used. Beginning with 2008 models, three additional tests will be used to adjust the city and highway estimates to account for higher speeds, air conditioning use, and colder temperatures. Note: EPA has established testing criteria for electric vehicles and plug-in hybrids that are slightly different than those for conventional vehicles. New Tests City Highway High Speed Air Conditioning Cold Temperature Detailed Comparison EPA Federal Test Procedure (City Schedule): Shows vehicle speed (mph) at each second of test

258

HUMAN RELIABILITY ANALYSIS FOR COMPUTERIZED PROCEDURES  

SciTech Connect

This paper provides a characterization of human reliability analysis (HRA) issues for computerized procedures in nuclear power plant control rooms. It is beyond the scope of this paper to propose a new HRA approach or to recommend specific methods or refinements to those methods. Rather, this paper provides a review of HRA as applied to traditional paper-based procedures, followed by a discussion of what specific factors should additionally be considered in HRAs for computerized procedures. Performance shaping factors and failure modes unique to computerized procedures are highlighted. Since there is no definitive guide to HRA for paper-based procedures, this paper also serves to clarify the existing guidance on paper-based procedures before delving into the unique aspects of computerized procedures.

Ronald L. Boring; David I. Gertman; Katya Le Blanc

2011-09-01T23:59:59.000Z

259

Operational test report for LERF Basin 242AL-44 integrity test  

SciTech Connect

This operational test report documents the results of LERF operational testing per operational test procedure (OTP) TFPE-WP-0231, ``LERF Basin Integrity Testing.`` The primary purpose of the OTP was to resolve test exceptions generated as a result of TFPE-WP-0184. The TOP was prepared and performed in accordance with WHC-SD-534-OTP-002, ``Operational Test Plan for the 242-A Evaporator Upgrades and the Liquid Effluent Retention Facility.`` WHC-S-086, ``Specification for Operational Testing of the Liquid Effluent Retention Facility, Basin Integrity Testing,`` identified the test requirements and acceptance criteria. The completed, signed-off test procedure is contained in Appendix A. The test log is contained in Appendix B. Section 2.1 describes all the test exceptions written during performance of the Operational Test Procedure. The test revisions generated during the testing are discussed in Section 2.2. The dispositioned test exception forms are contained in Appendix C.

Galioto, T.M.

1994-11-08T23:59:59.000Z

260

Light-Sensitive Papers as Controls for Testing Textile ...  

Science Conference Proceedings (OSTI)

... Voltage variations at most substations in the District of ... that temperature specifications for the testing of all ... as well as temperature, in test procedures. ...

2006-03-27T23:59:59.000Z

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Building Energy Simulation Test for Existing Homes (BESTEST-EX...  

NLE Websites -- All DOE Office Websites (Extended Search)

427 August 2010 Building Energy Simulation Test for Existing Homes (BESTEST-EX) Phase 1 Test Procedure: Building Thermal Fabric Cases Ron Judkoff, Ben Polly, and Marcus Bianchi...

262

Procedures and Standards for Residential Ventilation System Commissioning:  

NLE Websites -- All DOE Office Websites (Extended Search)

Procedures and Standards for Residential Ventilation System Commissioning: Procedures and Standards for Residential Ventilation System Commissioning: An Annotated Bibliography Title Procedures and Standards for Residential Ventilation System Commissioning: An Annotated Bibliography Publication Type Report LBNL Report Number LBNL-6142E Year of Publication 2013 Authors J. Chris Stratton, and Craig P. Wray Keywords ASHRAE 62.2, commissioning, procedures, residential, standards, ventilation Abstract Beginning with the 2008 version of Title 24, new homes in California must comply with ANSI/ASHRAE Standard 62.2-2007 requirements for residential ventilation. Where installed, the limited data available indicate that mechanical ventilation systems do not always perform optimally or even as many codes and forecasts predict. Commissioning such systems when they are installed or during subsequent building retrofits is a step towards eliminating deficiencies and optimizing the tradeoff between energy use and acceptable IAQ. Work funded by the California Energy Commission about a decade ago at Berkeley Lab documented procedures for residential commissioning, but did not focus on ventilation systems. Since then, standards and approaches for commissioning ventilation systems have been an active area of work in Europe. This report describes our efforts to collect new literature on commissioning procedures and to identify information that can be used to support the future development of residential-ventilation-specific procedures and standards. We recommend that a standardized commissioning process and a commissioning guide for practitioners be developed, along with a combined energy and IAQ benefit assessment standard and tool, and a diagnostic guide for estimating continuous pollutant emission rates of concern in residences (including a database that lists emission test data for commercially-available labeled products).

263

WRAP TRUPACT loading systems operational test report  

SciTech Connect

This Operational Test Report documents the operational testing of the TRUPACT process equipment HNF-3918, Revision 0, TRUPACT Operational Test Procedure. The test accomplished the following: Procedure validation; Facility equipment interface; Facility personnel support; and Subcontractor personnel support interface. Field changes are documented as test exceptions with resolutions. All resolutions are completed or a formal method is identified to track the resolution through to completion.

DOSRAMOS, E.V.

1999-09-01T23:59:59.000Z

264

Advanced Vehicle Testing and Evaluation  

SciTech Connect

The objective of the United States (U.S.) Department of Energy?s (DOEs) Advanced Vehicle Testing and Evaluation (AVTE) project was to provide test and evaluation services for advanced technology vehicles, to establish a performance baseline, to determine vehicle reliability, and to evaluate vehicle operating costs in fleet operations. Vehicles tested include light and medium-duty vehicles in conventional, hybrid, and all-electric configurations using conventional and alternative fuels, including hydrogen in internal combustion engines. Vehicles were tested on closed tracks and chassis dynamometers, as well as operated on public roads, in fleet operations, and over prescribed routes. All testing was controlled by procedures developed specifically to support such testing. Testing and evaluations were conducted in the following phases: ? Development of test procedures, which established testing procedures; ? Baseline performance testing, which established a performance baseline; ? Accelerated reliability testing, which determined vehicle reliability; ? Fleet testing, used to evaluate vehicle economics in fleet operation, and ? End of test performance evaluation. Test results are reported by two means and posted by Idaho National Laboratory (INL) to their website: quarterly progress reports, used to document work in progress; and final test reports. This final report documents work conducted for the entirety of the contract by the Clarity Group, Inc., doing business as ECOtality North America (ECOtality). The contract was performed from 1 October 2005 through 31 March 2013. There were 113 light-duty on-road (95), off-road (3) and low speed (15) vehicles tested.

Garetson, Thomas

2013-03-31T23:59:59.000Z

265

A quick procedure for model selection in the case of mixture of normal densities  

Science Conference Proceedings (OSTI)

The properties of robustness of the estimates based on the minimum integrated square error criterion can be exploited to set up a procedure in finding the number of the components of a mixture of Gaussian distributions. Each step of the procedure consists ... Keywords: Maximum likelihood, Minimum integrated square error, Monte Carlo significance test, Multivariate Gaussian mixtures, Simulation studies

A. Durio E. D. Isaia

2007-08-01T23:59:59.000Z

266

AGEING PROCEDURES ON LITHIUM BATTERIES IN AN INTERNATIONAL COLLABORATION CONTEXT  

DOE Green Energy (OSTI)

The widespread introduction of electrically-propelled vehicles is currently part of many political strategies and introduction plans. These new vehicles, ranging from limited (mild) hybrid to plug-in hybrid to fully-battery powered, will rely on a new class of advanced storage batteries, such as those based on lithium, to meet different technical and economical targets. The testing of these batteries to determine the performance and life in the various applications is a time-consuming and costly process that is not yet well developed. There are many examples of parallel testing activities that are poorly coordinated, for example, those in Europe, Japan and the US. These costs and efforts may be better leveraged through international collaboration, such as that possible within the framework of the International Energy Agency. Here, a new effort is under development that will establish standardized, accelerated testing procedures and will allow battery testing organizations to cooperate in the analysis of the resulting data. This paper reviews the present state-of-the-art in accelerated life testing in Europe, Japan and the US. The existing test procedures will be collected, compared and analyzed with the goal of international collaboration.

Jeffrey R. Belt; Ira Bloom; Mario Conte; Fiorentino Valerio Conte; Kenji Morita; Tomohiko Ikeya; Jens Groot

2010-11-01T23:59:59.000Z

267

Test definitions for the evaluation of seismic sensors.  

SciTech Connect

Most test methodologies referenced in this Test Definition and Test Procedures were designed by Sandia specifically for geophysical instrumentation evaluation. When appropriate, test instrumentation calibration is traceable to the National Institute for Standards Technology (NIST).

Kromer, Richard Paul (R.P. Kromer Consulting, Albuquerque, NM); Hart, Darren M.; Harris, James Mark

2007-07-01T23:59:59.000Z

268

Feature - Testing the Tesla  

NLE Websites -- All DOE Office Websites (Extended Search)

Testing the Tesla Testing the Tesla Tesla test Technician Geoff Amann takes the Tesla.through a driving cycle on Argonne's dynamometers. Argonne transportation engineers recently evaluated an all-electric Tesla Roadster at the Advanced Powertrain Research Facility's new two-wheel drive dynamometer laboratory. Data obtained from the Tesla will help researchers develop test procedures that provide an unbiased, consistent and practical approach to evaluating electric vehicles. "As we study these advanced vehicles, our knowledge base of the progression of vehicle electrification technology is enhanced," said chief engineer Mike Duoba. "In a rigorous, controlled manner, we are able to study many vehicle operating conditions to determine the impact on fuel consumption.

269

Minnesota Environmental Coordination Procedures Act (Minnesota) |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Minnesota Environmental Coordination Procedures Act (Minnesota) Minnesota Environmental Coordination Procedures Act (Minnesota) Minnesota Environmental Coordination Procedures Act (Minnesota) < Back Eligibility Utility Fed. Government Commercial Agricultural Investor-Owned Utility State/Provincial Govt Industrial Construction Municipal/Public Utility Local Government Residential Installer/Contractor Rural Electric Cooperative Tribal Government Low-Income Residential Schools Retail Supplier Institutional Multi-Family Residential Systems Integrator Fuel Distributor Nonprofit General Public/Consumer Transportation Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Home Weatherization Solar Wind Program Info State Minnesota Program Type Siting and Permitting This Act is designed to streamline the review procedures for a given

270

SPR Acquisition Procedures - Final Rulemaking | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Director of Operatons and Readiness, Strategic Petroleum Reserve, (202) 586-4691 SPR Crude Oil Acquisition Procedures - Final Rulemaking More Documents & Publications Price...

271

Slimhole Handbook- Procedures and Recommendations for Slimhole...  

Open Energy Info (EERE)

SAND99-1976 DOI Not Provided Check for DOI availability: http:crossref.org Online Internet link for Slimhole Handbook- Procedures and Recommendations for Slimhole Drilling and...

272

Laser Controlled Area Standard Operating Procedure (SOP)  

NLE Websites -- All DOE Office Websites (Extended Search)

PROCEDURE (SOP) This document defines the safety management program for the laser system listed below. All American National Standard Institute (ANSI) Hazard Class 3b and 4...

273

Microsoft Word - RM Procedures.doc  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Records Management Procedures for Storage, Transfer and Retrieval of Records from WNRC RETIREMENT OF RECORDS 1. The Program Office is responsible for originating the Records...

274

Broadband Over Power Lines (BPL) Simplified Emissions and Immunity Testing  

Science Conference Proceedings (OSTI)

The FCC Report & Order 04-245 calls out procedures for Certification testing of BPL components, which is required of BPL equipment manufacturers in order to sell their products. The test procedures for this Certification testing are contained in EPRI Technical Update 1011663. The FCC Certification testing regime is rather complicated to use for simply validating that the field strength is below the legal limits. A simplified emissions test procedure for field strength was needed for utilities to assure t...

2006-09-26T23:59:59.000Z

275

Project W-320 Heel Jet Secondary Catch Mechanism lateral load test  

SciTech Connect

This test procedure establishes the requirements for performing a lateral load test of the Heel Jet Secondary Catch Mechanism (SCM). Successful performance of this test will demonstrate that the SCM is capable of performing as designed when subjected to a force applied normal to the longitudinal axis of the mechanism. This test procedure is prepared following the recommended format and content guidelines for test procedures as prescribed in WHC-IP-1026, Engineering Practice Guidelines, Appendix K, Test Plans, Specifications, Procedures and Reports.

Bellomy, J.R.

1994-09-01T23:59:59.000Z

276

Whole-House Energy Analysis Procedures for Existing Homes: Preprint  

SciTech Connect

This paper describes a proposed set of guidelines for analyzing the energy savings achieved by a package of retrofits or an extensive rehabilitation of an existing home. It also describes certain field test and audit methods that can help establish accurate building system performance characteristics that are needed for a meaningful simulation of whole-house energy use. Several sets of default efficiency values have been developed for older appliances that cannot be easily tested and for which published specifications are not readily available. These proposed analysis procedures are documented more comprehensively in NREL Technical Report TP-550-38238.

Hendron, R.

2006-08-01T23:59:59.000Z

277

Code of Federal Regulations PROCEDURAL RULES FOR DOE NUCLEAR...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

PROCEDURAL RULES FOR DOE NUCLEAR ACTIVITIES Code of Federal Regulations PROCEDURAL RULES FOR DOE NUCLEAR ACTIVITIES This part sets forth the procedures to govern the conduct of...

278

PROCEDURE FOR CONDUCTING A RECORDS INVENTORY | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CONDUCTING A RECORDS INVENTORY PROCEDURE FOR CONDUCTING A RECORDS INVENTORY PROCEDURE FOR CONDUCTING A RECORDS INVENTORY PROCEDURE FOR CONDUCTING A RECORDS INVENTORY More Documents...

279

Lockout-Tagout Standard Operating Procedures, Policy 2010-002...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Lockout-Tagout Standard Operating Procedures, Policy 2010-002 Lockout-Tagout Standard Operating Procedures, Policy 2010-002 Lockout-Tagout Standard Operating Procedures for...

280

ISDSN Sensor System Phase One Test Report  

Science Conference Proceedings (OSTI)

This Phase 1 Test Report documents the test activities and results completed for the Idaho National Laboratory (INL) sensor systems that will be deployed in the meso-scale test bed (MSTB) at Florida International University (FIU), as outlined in the ISDSN-MSTB Test Plan. This report captures the sensor system configuration tested; test parameters, testing procedure, any noted changes from the implementation plan, acquired test data sets, and processed results.

Gail Heath

2011-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Controllable procedural map generation via multiobjective evolution  

Science Conference Proceedings (OSTI)

This paper shows how multiobjective evolutionary algorithms can be used to procedurally generate complete and playable maps for real-time strategy (RTS) games. We devise heuristic objective functions that measure properties of maps that impact important ... Keywords: Evolutionary computation, Multiobjective optimisation, Procedural content generation, RTS, Real-time strategy games, StarCraft

Julian Togelius; Mike Preuss; Nicola Beume; Simon Wessing; Johan Hagelbäck; Georgios N. Yannakakis; Corrado Grappiolo

2013-06-01T23:59:59.000Z

282

Irrigation customer survey procedures and results  

SciTech Connect

This report describes the statistical procedures, administrative procedures, and results of a telephone survey designed to collect primary data from individuals in the Pacific Northwest region who use electricity in irrigating agricultural crops. The project was intended to collect data useful for a variety of purposes, including conservation planning, load forecasting, and rate design.

Harrer, B.J.; Johnston, J.W.; Dase, J.E.; Hattrup, M.P.; Reed, G.

1987-03-01T23:59:59.000Z

283

PHYSICAL PLANT OPERATING POLICY AND PROCEDURE  

E-Print Network (OSTI)

PHYSICAL PLANT OPERATING POLICY AND PROCEDURE PP/OP 04.07: Insulation, Asbestos Containing Building for the implementation and maintenance of an active insulation, asbestos containing building material abatement program is identified. 2. Procedures a. Insulation and Asbestos Containing Building Material Removal (1) Only certified

Gelfond, Michael

284

COLORADO SCHOOL OF MINES EMERGENCY MANAGEMENT PROCEDURE  

E-Print Network (OSTI)

COLORADO SCHOOL OF MINES EMERGENCY MANAGEMENT PROCEDURE #12;INTRODUCTION COLORADO SCHOOL OF MINES EMERGENCY MANAGEMENT PROCEDURE 1 EMERGENCY PREPAREDNESS AT THE COLORADO SCHOOL OF MINES Emergencies and psychologically prepared to handle unexpected emergencies is an individual, as well as an organizational

285

Definition: Operating Procedure | Open Energy Information  

Open Energy Info (EERE)

Procedure Procedure Jump to: navigation, search Dictionary.png Operating Procedure A document that identifies specific steps or tasks that should be taken by one or more specific operating positions to achieve specific operating goal(s). The steps in an Operating Procedure should be followed in the order in which they are presented, and should be performed by the position(s) identified. A document that lists the specific steps for a system operator to take in removing a specific transmission line from service is an example of an Operating Procedure.[1] Related Terms transmission lines, transmission line References ↑ Glossary of Terms Used in Reliability Standards An i LikeLike UnlikeLike You like this.Sign Up to see what your friends like. nline Glossary Definition Retrieved from

286

Procedures to predict vertical differential soil movement for expansive soils  

E-Print Network (OSTI)

Damage to lightly loaded structures, paving and service piping in areas of expansive clay soils has occurred throughout the world. The cause of this damage has been the inability to accurately model expansive soil movement so that foundations are adequately designed to withstand the movement. The amount and rate of differential soil movement for expansive soils is due to a combination of soil characteristics, namely: suction compression index, unsaturated permeability, and diffusivity. Currently, geotechnical engineers run tests to measure the soil properties required to estimate differential soil movements. However, there seems to be apprehension toward attempting these soil movement calculations due to the perceived complexity of the calculations or a simple lack of understanding of the theory. The procedures delineating the step by step process used to calculate suction profiles and volume strains of expansive soils is presented. These procedures include the methodology to predict soil heave and shrink underneath shallow foundations which generate maximum center lift and maximum edge lift slab distortion modes. The main contributions of this research are: equations and procedures to calculate the equilibrium suction profile and depth to constant suction for a particular soil profile and location, equations to calculate the horizontal velocity flow of water in unsaturated soils, the methodology to predict differential soil movement shortly after a slab has been constructed and before the soil under the slab has reached an equilibrium moisture content, and the procedures to apply differential soil movement theory to soil profiles with shallow foundation design.

Naiser, Donald David

1997-01-01T23:59:59.000Z

287

FSME Procedure Approval Termination of Uranium Milling Licenses in Agreement  

E-Print Network (OSTI)

Any changes to the procedure will be the responsibility of the FSME Procedure Contact. Copies of the FSME procedures will be available through the NRC website. Procedure Title: Termination of Uranium Milling

Robert J. Lewis; A. Duncan White; William R. Rautzen

2010-01-01T23:59:59.000Z

288

Policies and Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Services » Communication & Engagement » EM SSAB » Policies and Services » Communication & Engagement » EM SSAB » Policies and Procedures Policies and Procedures The purpose of this document is to provide guidance regarding the operation of the Environmental Management Site-Specific Advisory Board (EM SSAB or Board). Policies and Procedures More Documents & Publications Memorandum: Regarding Delegation of Designated Federal Officials for Site Specific Advisory Boards EM SSAB Charter DOE Manual - ADVISORY COMMITTEE MANAGEMENT PROGRAM Waste Management Nuclear Materials & Waste Tank Waste and Waste Processing Waste Disposition Packaging and Transportation Site & Facility Restoration Deactivation & Decommissioning (D&D) Facility Engineering Soil & Groundwater Sustainability Program Management Safety

289

PART 1021-NATIONAL ENVIRONMENTAL POLICY ACT IMPLEMENTING PROCEDURES  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Effective Nov 14, 2011 1 Effective Nov 14, 2011 1 PART 1021-NATIONAL ENVIRONMENTAL POLICY ACT IMPLEMENTING PROCEDURES Subpart A-General Sec. 1021.100 Purpose. 1021.101 Policy. 1021.102 Applicability. 1021.103 Adoption of CEQ NEPA regulations. 1021.104 Definitions. 1021.105 Oversight of Agency NEPA activities. Subpart B-DOE Decisionmaking 1021.200 DOE planning. 1021.210 DOE decisionmaking. 1021.211 Interim actions: Limitations on actions during the NEPA process. 1021.212 Research, development, demonstration, and testing. 1021.213 Rulemaking. 1021.214 Adjudicatory proceedings. 1021.215 Applicant process. 1021.216 Procurement, financial assistance, and joint ventures. Subpart C-Implementing Procedures 1021.300 General requirements. 1021.301 Agency review and public participation.

290

MENTAL POLICY ACT IMPLE- MENTING PROCEDURES Subpart A-General  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9 9 Department of Energy § 1021.102 PART 1021-NATIONAL ENVIRON- MENTAL POLICY ACT IMPLE- MENTING PROCEDURES Subpart A-General Sec. 1021.100 Purpose. 1021.101 Policy. 1021.102 Applicability. 1021.103 Adoption of CEQ NEPA regulations. 1021.104 Definitions. 1021.105 Oversight of Agency NEPA activi- ties. Subpart B-DOE Decisionmaking 1021.200 DOE planning. 1021.210 DOE decisionmaking. 1021.211 Interim actions: Limitations on ac- tions during the NEPA process. 1021.212 Research, development, demonstra- tion, and testing. 1021.213 Rulemaking. 1021.214 Adjudicatory proceedings. 1021.215 Applicant process. 1021.216 Procurement, financial assistance, and joint ventures. Subpart C-Implementing Procedures 1021.300 General requirements. 1021.301 Agency review and public participa-

291

10 CFR 1021 -- National Environmental Policy Act Implementing Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1021 -- NATIONAL 1021 -- NATIONAL ENVIRONMENTAL POLICY ACT IMPLEMENTING PROCEDURES Subpart A -- General Sec. 1021.100 Purpose. 1021.101 Policy. 1021.102 Applicability. 1021.103 Adoption of CEQ NEPA regulations. 1021.104 Definitions. 1021.105 Oversight of Agency NEPA activities. Subpart B -- DOE Decisionmaking 1021.200 DOE planning. 1021.210 DOE decisionmaking. 1021.211 Interim actions: Limitations on actions during the NEPA process. 1021.212 Research, development, demonstration, and testing. 1021.213 Rulemaking. 1021.214 Adjudicatory proceedings. 1021.215 Applicant process. 1021.216 Procurement, financial assistance, and joint ventures. Subpart C -- Implementing Procedures 1021.300 General requirements. 1021.301 Agency review and public participation. 1021.310 Environmental impact statements.

292

Handicapped Parking Procedures (HQ) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Handicapped Parking Procedures (HQ) Handicapped Parking Procedures (HQ) Handicapped Parking Procedures (HQ) It is the policy of the Department of Energy (DOE) that its parking facility be operated in a manner responsive to the needs of the Department, and for the maximum benefit of its employees. Individuals with temporary or permanent mobility impairment who, because of their condition, have a need to request a handicapped parking permit for the Forrestal or Germantown facilities, should use the following procedures: Complete a Parking Application Complete the Permit Application form DOE F 1400.12. In instances when the Parking Management personnel can visually assess an applicant's mobility impairment (i.e. use of crutches, walker, etc.), a temporary parking permit may be granted. At the time of application, the

293

Antivirus Procedures, Cyber Security, Information Technology...  

NLE Websites -- All DOE Office Websites (Extended Search)

Anti-virus Software Trend OfficeScan for PCs & Trend Micro Security for Mac Anti-Virus procedures are an important component of BNL's host-based security architecture. Anti-Virus...

294

Using project procedure diagrams for milestone planning  

Science Conference Proceedings (OSTI)

This paper presents Project Procedure Diagrams (PPDs) as a technique for specifying and elaborating project milestone plans. The graphical syntax of PPDs is similar to UML activity diagrams. The operational semantics is based on token flow and resembles ...

Klaus Bergner; Jan Friedrich

2010-07-01T23:59:59.000Z

295

AOCS Standard Procedure Ck 2-09  

Science Conference Proceedings (OSTI)

Determination of Various Properties of Biodiesel by the QTA® System Method AOCS Standard Procedure Ck 2-09 Methods Methods and Analyses Analytical Chemistry Methods Downloads Methods Downloads AOCS ...

296

Revolutionizing standard operating procedures in biomanufacturing  

E-Print Network (OSTI)

In its quest to become a High Reliability Performance (HRP) organization, Amgen manufacturing operations desires to further improve its adherence to, and effectiveness of, its standard operating procedures (SOPs). SOPs are ...

Nag, Aditya

2013-01-01T23:59:59.000Z

297

Chapter 13 - Simplified Acquisition Procedures | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Card Policy and Operating Procedures 13.2PurchaseOrders0.pdf More Documents & Publications OPAM Policy Acquisition Guides Chapter 16 - Types of Contracts Policy Flash 2011-75...

298

Proposal Submittal and Scheduling Procedures for Macromolecular...  

NLE Websites -- All DOE Office Websites (Extended Search)

merit and to assure that all ES&H guidelines are met in accordance with standard SSRL policies and procedures. Sufficient generic information to enable Proposal Review Panel review...

299

BOOKS AND PROCEEDINGS POLICIES PROCEDURE FOR ...  

Science Conference Proceedings (OSTI)

Nov 18, 2008 ... PROCEDURE FOR ADDRESSING PLAGIARISM CLAIMS. TMS Content Development ... Editor Guidelines: It is the policy of TMS that each editor who is named and included on the cover/title page of the book is entitled to one ...

300

Strategies for Evaluating Quality Assurance Procedures  

Science Conference Proceedings (OSTI)

The evaluation strategies outlined in this paper constitute a set of tools beneficial to the development and documentation of robust automated quality assurance (QA) procedures. Traditionally, thresholds for the QA of climate data have been based ...

Imke Durre; Matthew J. Menne; Russell S. Vose

2008-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Glove Perforations During Interventional Radiological Procedures  

SciTech Connect

Intact surgical gloves are essential to avoid contact with blood and other body fluids. The objective of this study was to estimate the incidence of glove perforations during interventional radiological procedures. In this study, a total of 758 gloves used in 94 interventional radiological procedures were examined for perforations. Eleven perforations were encountered, only one of which was of occult type. No significant difference in the frequency of glove perforation was found between the categories with varying time duration.

Leena, R. V., E-mail: leenarv_76@yahoo.co.uk; Shyamkumar, N. K. [Christian Medial College, Department of Radiodiagnosis (India)

2010-04-15T23:59:59.000Z

302

Practical Procedures for Auditing Industrial Boiler Plants  

E-Print Network (OSTI)

Industrial boiler plants are an area of opportunity in virtually every industry to save energy and reduce costs by using relatively simple, inexpensive auditing procedures. An energy audit consists of inspection, measurement, analysis, and the preparation of recommendations. A complete boiler plant program will consider each individual boiler, boiler room auxiliary equipment, steam distribution and return systems, and steam end use equipment. This paper summarizes the practical procedures, techniques, and instrumentation which Nabisco uses in its boiler plant energy conservation program.

O'Neil, J. P.

1980-01-01T23:59:59.000Z

303

CPC thermal collector test plan  

DOE Green Energy (OSTI)

A comprehensive set of test procedures has evolved at Argonne National Laboratory for establishing the performance of compound parabolic and related concentrating thermal collectors with large angular fields of view. The procedures range from separate thermal and optical tests, to overall performance tests. A calorimetric ratio technique has been developed to determine the heat output of a collector without knowledge of the heat transfer fluid's mass flow rate and heat capacity. Sepcial attention is paid to the problem of defining and measuring the incident solar flux with respect to which the collector efficiency is to be calculated.

Reed, K A

1977-01-01T23:59:59.000Z

304

NREL: Biomass Research - Standard Procedures for Microalgal Biofuels  

NLE Websites -- All DOE Office Websites (Extended Search)

Standard Procedures for Microalgal Biofuels Analysis Standard Procedures for Microalgal Biofuels Analysis Capabilities in Microalgal Analysis NREL's Algal Biofuels Research team can work with you to analyze the chemical composition of algae as a biomass feedstock. NREL develops laboratory analytical procedures (LAPs) for analyzing microalgal biofuels. These procedures help scientists and analysts understand more about the chemical composition of algae as a feedstock to convert to biofuels. For more procedures, see the biomass characterization LAPs. Laboratory Analytical Procedures NREL wrote these analytical procedures to help the research community analyze algae. Summative Mass Analysis of Algal Biomass - Integration of Analytical Procedures Download Procedure This procedure guides the integration of LAPs to measure algal biomass

305

Battery testing for photovoltaic applications  

SciTech Connect

Battery testing for photovoltaic (PV) applications is funded at Sandia under the Department of Energy`s (DOE) Photovoltaic Balance of Systems (BOS) Program. The goal of the PV BOS program is to improve PV system component design, operation, reliability, and to reduce overall life-cycle costs. The Sandia battery testing program consists of: (1) PV battery and charge controller market survey, (2) battery performance and life-cycle testing, (3) PV charge controller development, and (4) system field testing. Test results from this work have identified market size and trends, PV battery test procedures, application guidelines, and needed hardware improvements.

Hund, T.

1996-11-01T23:59:59.000Z

306

Certification testing for small wind turbines  

DOE Green Energy (OSTI)

This paper describes the testing procedures for obtaining type certification for a small wind turbine. Southwest Windpower (SWWP) is seeking type certification from Underwriters Laboratory (UL) for the AIR 403 wind turbine. UL is the certification body and the National Renewable Energy Laboratory (NREL) is providing technical assistance including conducting the certification testing. This is the first small turbine to be certified in the US, therefore standards must be interpreted and test procedures developed.

Corbus, D.; Link, H.; Butterfield, S.; Stork, C.; Newcomb, C.

1999-10-20T23:59:59.000Z

307

CC Pressure Test  

SciTech Connect

The inner vessel heads including bypass and beam tubes had just been welded into place and dye penetrant checked. The vacuum heads were not on at this time but the vacuum shell was on covering the piping penetrating into the inner vessel. Signal boxes with all feed through boards, the instrumentation box, and high voltage boxes were all installed with their pump outs capped. All 1/4-inch instrumentation lines were terminated at their respective shutoff valves. All vacuum piping used for pumping down the inner vessel was isolated using o-ring sealed blind flanges. PV215A (VAT Series 12), the 4-inch VRC gate valve isolating the cyropump, and the rupture disk had to be removed and replaced with blind flanges before pressurizing due to their pressure limitations. Stresses in plates used as blind flanges were checked using Code calcualtions. Before the CC test, vacuum style blanks and clamps were hydrostatically pressure tested to 150% of the maximum test pressure, 60 psig. The Code inspector and Research Division Safety had all given their approval to the test pressure and procedure prior to filling the vessel with argon. The test was a major success. Based on the lack of any distinguishable pressure drop indicated on the pressure gages, the vessel appeared to be structurally sound throughout the duration of the test (approx. 3 hrs.). A major leak in the instrumentation tubing was discovered at half of the maximum test pressure and was quickly isolated by crimping and capping with a compression fitting. There were some slight deviations in the actual procedure used. The 44 psig relief valve located just outside the cleanroom had to be capped until the pressure in the vessel indicated 38 psi. This was to allow higher supply pressures and hence, higher flows through the pressurizing line. Also, in order to get pressure readings at the cryostat without exposing any personnel to the potentially dangerous stored energy near the maximum test pressure, a camera was installed at the top of the vessel to view the indicator mounted there. The monitor was viewed at the ante room adjacent to the cleanroom. The holding pressure of 32 psig (4/5 of the maximum test pressure) was only maintained for about 20 minutes instead of the half hour recommendation in the procedure. We felt that this was sufficient time to Snoop test and perform the pressure drop test. After the test was completed, the inspector for CBI Na-Con and the Research Divison Safety Officer signed all of required documentation.

Dixon, K.; /Fermilab

1990-07-12T23:59:59.000Z

308

Advanced Technology Vehicle Testing  

DOE Green Energy (OSTI)

The light-duty vehicle transportation sector in the United States depends heavily on imported petroleum as a transportation fuel. The Department of Energy’s Advanced Vehicle Testing Activity (AVTA) is testing advanced technology vehicles to help reduce this dependency, which would contribute to the economic stability and homeland security of the United States. These advanced technology test vehicles include internal combustion engine vehicles operating on 100% hydrogen (H2) and H2CNG (compressed natural gas) blended fuels, hybrid electric vehicles, neighborhood electric vehicles, urban electric vehicles, and electric ground support vehicles. The AVTA tests and evaluates these vehicles with closed track and dynamometer testing methods (baseline performance testing) and accelerated reliability testing methods (accumulating lifecycle vehicle miles and operational knowledge within 1 to 1.5 years), and in normal fleet environments. The Arizona Public Service Alternative Fuel Pilot Plant and H2-fueled vehicles are demonstrating the feasibility of using H2 as a transportation fuel. Hybrid, neighborhood, and urban electric test vehicles are demonstrating successful applications of electric drive vehicles in various fleet missions. The AVTA is also developing electric ground support equipment (GSE) test procedures, and GSE testing will start during the fall of 2003. All of these activities are intended to support U.S. energy independence. The Idaho National Engineering and Environmental Laboratory manages these activities for the AVTA.

James Francfort

2003-11-01T23:59:59.000Z

309

Export Authorizations - Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Export Authorizations - Procedures Export Authorizations - Procedures Export Authorizations - Procedures Part II, Section 202(e) of the Federal Power Act (FPA) states that exports of electric energy should be allowed unless the proposed export would impair the sufficiency of electric power supply within the U.S. or would impede or tend to impede the coordinated use of the U.S. power supply network. Based on these guidelines, DOE will grant authorization to export electric energy if it is determined that: 1.Sufficient generating resources exist such that the exporter could sustain the export while still maintaining adequate generating resources to meet all firm supply obligations; and, 2.The export would not cause operating parameters on regional transmission systems to fall outside of established industry criteria.

310

Property:FieldProcedures | Open Energy Information  

Open Energy Info (EERE)

FieldProcedures FieldProcedures Jump to: navigation, search Property Name FieldProcedures Property Type Text Description Description of actions, equipment and footprint of the exploration activity Subproperties This property has the following 39 subproperties: A Active Seismic Techniques Airborne Gravity Survey Audio-Magnetotellurics C Controlled Source Audio MT Cross-Dipole Acoustic Log D DC Resistivity Survey (Dipole-Dipole Array) DC Resistivity Survey (Mise-Á-La-Masse) DC Resistivity Survey (Pole-Dipole Array) DC Resistivity Survey (Schlumberger Array) DC Resistivity Survey (Wenner Array) Development Drilling Direct-Current Resistivity Survey Drilling Techniques E Earth Tidal Analysis Electrical Profiling Configurations Electromagnetic Techniques Exploration Drilling F FMI Log Frequency-Domain Electromagnetic Survey

311

Emergency Response & Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

National Security + Safety » Emergency Response & Procedures National Security + Safety » Emergency Response & Procedures Emergency Response & Procedures November 1, 2013 A Statement from U.S. Secretary of Energy Ernest Moniz Regarding Fukushima On Friday, I made my first visit to the Fukushima Daiichi Nuclear Power Station. It is stunning that one can see firsthand the destructive force of the tsunami even more than two and a half years after the tragic events October 29, 2013 Workers repair power lines in the Mid-Atlantic shortly after Hurricane Sandy. | Photo courtesy of the Energy Department. Hurricane Sandy One Year Later: Rebuilding Stronger, More Resilient Communities The Energy Department continues to take actions to protect our energy infrastructure, adapt to climate change and build partnerships to make

312

Remote procedure execution software for distributed systems  

SciTech Connect

Remote Procedure Execution facilitates the construction of distributed software systems, spanning computers of various types. Programmers who use the RPX package specify subroutine calls which are to be executed on a remote computer. RPX is used to generate code for dummy routines which transmit input parameters and receive output parameters, as well as a main program which receives procedure call requests, calls the requested procedure, and returns the result. The package automatically performs datatype conversions and uses an appropriate connection oriented protocol. Supported operating systems/processors are VMS(VAX), UNIX(MIPS R2000, R3000) and Software Components Group's pSOS (680x0). Connection oriented protocols are supported over Ethernet (TCP/IP) and RS232 (a package of our own design). 2 refs., 2 figs.

Petravick, D.L.; Berman, E.F.; Sergey, G.P.

1989-05-01T23:59:59.000Z

313

Public Comment Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Public Comment Procedures Public Comment Procedures Public Comment Procedures In response to an application, any person may file a protest, comments, or a motion to intervene or notice of intervention, as applicable. Any person wishing to become a party to the proceeding must file a motion to intervene or notice of intervention, as applicable. Dockets Open for Public Comment A list of current dockets open for public comment can be found on the main Natural Gas Regulations page here. FILINGS: Filings may be submitted using one of the following methods. Please be sure to include Docket No. and Application Name with your filing: E-mail: fergas@hq.doe.gov (you must include FE Docket No. in the Subject line of the email) Regular Mail: (should include an original and three paper copies of

314

Micro-tensile testing system  

DOE Patents (OSTI)

A micro-tensile testing system providing a stand-alone test platform for testing and reporting physical or engineering properties of test samples of materials having thicknesses of approximately between 0.002 inch and 0.030 inch, including, for example, LiGA engineered materials. The testing system is able to perform a variety of static, dynamic, and cyclic tests. The testing system includes a rigid frame and adjustable gripping supports to minimize measurement errors due to deflection or bending under load; serrated grips for securing the extremely small test sample; high-speed laser scan micrometers for obtaining accurate results; and test software for controlling the testing procedure and reporting results.

Wenski, Edward G. (Lenexa, KS)

2007-08-21T23:59:59.000Z

315

Micro-tensile testing system  

DOE Patents (OSTI)

A micro-tensile testing system providing a stand-alone test platform for testing and reporting physical or engineering properties of test samples of materials having thicknesses of approximately between 0.002 inch and 0.030 inch, including, for example, LiGA engineered materials. The testing system is able to perform a variety of static, dynamic, and cyclic tests. The testing system includes a rigid frame and adjustable gripping supports to minimize measurement errors due to deflection or bending under load; serrated grips for securing the extremely small test sample; high-speed laser scan micrometers for obtaining accurate results; and test software for controlling the testing procedure and reporting results.

Wenski, Edward G. (Lenexa, KS)

2007-07-17T23:59:59.000Z

316

Coordinate Measuring Machine Pit Artifact Inspection Procedure  

Science Conference Proceedings (OSTI)

The goal of this document is to outline a procedure for dimensional measurement of Los Alamos National Laboratory's CMM Pit Artifact. This procedure will be used by the Manufacturing Practice's Inspection Technology Subgroup of the Interagency Manufacturing Operations Group and Joint Operations Weapon Operations Group (IMOG/JOWOG 39) round robin participants. The intent is to assess the state of industry within the Nuclear Weapons Complex for measurements made on this type of part and find which current measurement strategies and techniques produce the best results.

Montano, Joshua D. [Los Alamos National Laboratory

2012-07-31T23:59:59.000Z

317

Tests for Convergence Clubs  

E-Print Network (OSTI)

?1 has a mixed (heterogeneous) structure, the event of rejecting the null allows for a non zero fraction ? = N1/N of the series to be stationary. However, as Breitung and Pesaran (2008) and Im et al. (2003) note, the test does not provide any guidance... statistic) is removed and the test is performed on the remaining series. This procedure iterates until the unit root null does not reject. At the point of termination, the result is the partition of the series into stationary (S) and nonstationary groups...

Corrado, Luisa; Weeks, Melvyn

2011-01-26T23:59:59.000Z

318

Damage tolerance design procedures for an automotive composite  

DOE Green Energy (OSTI)

Among the durability issues of concern in the use of composites in automobile structures is the damaging effects that low-energy impacts (e.g., tool drops and roadway kickups) might have on strength and stiffness. This issue was experimentally investigated, and recommended design evaluation procedures were developed for a candidate automotive structural composite--a structural reaction injection-molded polyurethane reinforced with continuous strand, swirl-mat E-glass fibers. Two test facilities were built to cover the range of impacts of interest--a pendulum device to characterize the effects of relative heavy objects at low velocities and an air gun to characterize the effects of relatively light objects at higher velocities. In all cases, the test specimen was a 9 x 9 x 1/8-in.-thick plate clamped on an 8-in.-diam circle. Sixty-five impact tests were performed. Included were tests using various impactor sizes and weights, tests at {minus}40 F, and tests on specimens that has been presoaked in water or exposed to battery acid. Damage areas were determined using ultrasonic C-scans, and the resulting areas were found to correlate with the quantity impactor mass to a power times velocity. A design curve was derived from the correlation and validated using dropped brick tests. To evaluate strength and stiffness reductions, the impacted plate specimens were cut into tensile, compressive, and fatigue test specimens that were used to determine reductions as a function of damage area. It was found that for design purposes, the strength reduction could be determined by representing the damage area by a circular hole of equivalent area.

Corum, J.M.; Battiste, R.L.

1998-11-01T23:59:59.000Z

319

GRIEVANCE PROCEDURES The State Employee Grievance Procedure Act provides that each agency and department of State government shall establish a  

E-Print Network (OSTI)

PROCEDURE GRIEVANCE PROCEDURES The State Employee Grievance Procedure Act provides that each agency and department of State government shall establish a written employee grievance procedure approved by the State Personnel Director. A copy of the approved procedure plan shall be furnished to the employees of the agency

Kunkle, Tom

320

Page 1 of 5 OUA CSP Procedures  

E-Print Network (OSTI)

Page 1 of 5 OUA CSP Procedures Author(s): Kayla Polak Date Issued: March 2013 Issuing Area: Flexible Learning Support Subject: OUA Commonwealth Supported Places (CSP) Circulation: University OUA CSP award courses. As the Flexible Learning Support office at Curtin University is the conduit

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Chemical Spill Response Procedure Initial Response  

E-Print Network (OSTI)

Chemical Spill Response Procedure Initial Response 1. Advise lab occupants of the spill such as quantity spilled and chemical name. Risk Assessment 3. Conduct an initial risk assessment to determine if to the chemical spill. This link can be found at the bottom of the Campus Security homepage, http

322

A COMPUTATIONAL PROCEDURE TO ESTIMATE THE FUNDAMENTAL  

E-Print Network (OSTI)

of the grounding systems is to dissipate a current injection* * at an electrical substation produced A COMPUTATIONAL PROCEDURE TO ESTIMATE THE FUNDAMENTAL PARAMETERS IN GROUNDING. Abstract The grounding grid design must be made in such a way that the funda- mental parameters do

Bendito, Enrique

323

Fusion procedure for the Brauer algebra  

E-Print Network (OSTI)

We show that all primitive idempotents for the Brauer algebra B_n(w) can be found by evaluating a rational function in several variables which has the form of a product of R-matrix type factors. This provides an analogue of the fusion procedure for B_n(w).

A. P. Isaev; A. I. Molev

2008-12-22T23:59:59.000Z

324

Security Procedures Caltech Campus Security Dispatch  

E-Print Network (OSTI)

Security Procedures Caltech Campus Security Dispatch: 5000 (from any Caltech phone) or (626) 395-5000 (from any phone) When emergencies arise, contact Caltech Campus Security MEDICAL If someone experiences a medical emergency: · Remain calm · Notify Campus Security Dispatch · Do NOT move victim EARTHQUAKE When

Goddard III, William A.

325

Energy consumption for baking and characteristics of baked product in relation to type of oven and baking procedure  

Science Conference Proceedings (OSTI)

Data were obtained and analyzed on 1) energy consumption when a test food was baked with four types of electric ovens (electric range oven, table model conventional oven, table model forced convection oven, and table model broiler/toaster oven) with three cooking procedures (participant's own procedure, preheated procedure, and cold start procedure); 2) patterns of energy consumption in 10-minute intervals; and 3) the characteristics of the finished food. Twenty participants from households in Columbus, Ohio, baked loaves of quick bread in a laboratory in the four types of ovens with three cooking procedures. Statistical analyses of data included analyses of variance, Tukey test, and Duncan's multiple range test. Significantly more energy was used with the participants' own procedures than with either the preheated or the cold start procedure (p < .01). There was no consistency in total energy consumption between the preheated and the cold start procedures in the four types of ovens. The electric range oven consumed significantly more energy than the other three types of ovens in the first 10-minute interval; however, the table model forced convection oven consumed significantly more energy than other ovens in the second and third 10-minute intervals. No consistent patterns were observed for volume and weight loss of breads baked with the three cooking procedures, but use of the table model forced convection oven always resulted in larger volume than with other ovens.

Nee, Y.

1982-01-01T23:59:59.000Z

326

A Comparison of WD-EPMA Heterogeneity Testing ...  

Science Conference Proceedings (OSTI)

A Comparison of WD-EPMA Heterogeneity Testing Procedures. Summary: The heterogeneity of the four elements in a TiAl ...

2012-10-02T23:59:59.000Z

327

Deflagration studies on waste Tank 101-SY: Test plan  

DOE Green Energy (OSTI)

This report discusses test procedures and calibration of equipment to study the flammability and deflagration of hydrogen, nitrous oxide, and air in waste tanks. (JL)

Cashdollar, K.L.; Zlochower, I.A.; Hertzberg, M.

1991-06-01T23:59:59.000Z

328

Policy and Procedures for the Review of Federal Actions Impacting...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Policy and Procedures for the Review of Federal Actions Impacting the Environment Policy and Procedures for the Review of Federal Actions Impacting the Environment This manual...

329

ICR-ICE Standard Operating Procedures (Update Sept 2013) | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

ICR-ICE Standard Operating Procedures (Update Sept 2013) ICR-ICE Standard Operating Procedures (Update Sept 2013) ICRICE SOPSep 2013Final.pdf More Documents & Publications...

330

PROCEDURE FOR PREPARING RECORDS INVENTORY AND DISPOSITION SCHEDULES...  

NLE Websites -- All DOE Office Websites (Extended Search)

PREPARING RECORDS INVENTORY AND DISPOSITION SCHEDULES (RIDS) PROCEDURE FOR PREPARING RECORDS INVENTORY AND DISPOSITION SCHEDULES (RIDS) This document lists the procedures for...

331

PARS II Standard Operating Procedure (SOP) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Standard Operating Procedure (SOP) PARS II Standard Operating Procedure (SOP) PARSIISOPVersion1.120110811.pdf More Documents & Publications External Independent Review (EIR)...

332

ICR-ICE Standard Operating Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

ICR-ICE Standard Operating Procedures ICR-ICE Standard Operating Procedures ICE-ICR SOP.pdf More Documents & Publications External Independent Review (EIR) Standard Operating...

333

Forrestal Garage Parking Procedures, Revised August 12, 2010  

Energy.gov (U.S. Department of Energy (DOE))

Forrestal Garage Parking Procedures - The Forrestal Facility Parking Guide was created to define policies and procedures governing the assignment, use, and management of parking spaces controlled...

334

Review of International Methods of Test to Rate the Efficiency of Water Heaters  

E-Print Network (OSTI)

test procedure load profiles. The equivalent parameters fortable of all the load profiles is included as Appendix 1.to the draws in the load profile, the transitional test

Lutz, Jim

2012-01-01T23:59:59.000Z

335

Chesapeake Testing  

Science Conference Proceedings (OSTI)

... Send E-Mail to NVLAP at: NVLAP@nist.gov. Personal Body Armor Testing. ... 7 Ballistic Resistance of Body Armor, Section 7, Ballistic Test Methods. ...

2014-01-03T23:59:59.000Z

336

Structural Testing  

DOE Green Energy (OSTI)

Structural testing at the National Wind Technology Center (NWTC) offers many benefits to wind turbine companies. NWTC includes a new high bay large enough to test any blade expected during the next 5 years. (There are four test bays.) In 1995, NWTC developed a saphisticated data acquisition system, known as the Blade Structural Testing Real-time Acquisition Interface Network (BSTRAIN), to monitor structural testing through 24-hour continuous video surveillance. NWTC recommends ultimate static-strength and fatigue testing, with nondestructive testing in some cases (vibrational testing is covered in a separate information sheet).

NONE

1996-06-01T23:59:59.000Z

337

Issues in emissions testing of hybrid electric vehicles.  

DOE Green Energy (OSTI)

Argonne National Laboratory (ANL) has tested more than 100 prototype HEVs built by colleges and universities since 1994 and has learned that using standardized dynamometer testing procedures can be problematic. This paper addresses the issues related to HEV dynamometer testing procedures and proposes a new testing approach. The proposed ANL testing procedure is based on careful hybrid operation mode characterization that can be applied to certification and R and D. HEVs also present new emissions measurement challenges because of their potential for ultra-low emission levels and frequent engine shutdown during the test cycles.

Duoba, M.; Anderson, J.; Ng, H.

2000-05-23T23:59:59.000Z

338

Test Laboratory Instructions (Updated 2/12)  

E-Print Network (OSTI)

Test Laboratory Instructions (Updated 2/12) In California, manufacturers of State- and federally Energy Commission (Energy Commission). This reported data must come from an approved test laboratory performing the test procedure prescribed by law for the appliance. These instructions will walk you through

339

Attribution and Apportionment - Preliminary Estimation Procedures  

NLE Websites -- All DOE Office Websites (Extended Search)

Preliminary Estimation Procedures Preliminary Estimation Procedures FHWA completes several steps in the motor fuel analysis process prior to beginning the annual State-by-State analysis. These steps include an estimation of non-highway fuel uses, public fuel uses, and gasohol consumption. The estimation models are briefly described below. The models require data from several outside sources. One major dataset is the Census Bureau's Vehicle Inventory and Use Survey (VIUS). This data set contains information on annual vehicle miles of travel, percent of off-road use, major use of the truck (agriculture, retail, etc.), engine type, and the State in which the truck is registered. VIUS does not, however, provide a fuel use breakdown between gasoline and gasohol, on-road versus off-road fuel economy, or a distribution of off-road travel by State. The VIUS is conducted every five years; the latest survey was in 1997.

340

Proposal Submittal and Scheduling Procedures for Macromolecular  

NLE Websites -- All DOE Office Websites (Extended Search)

Proposal Submittal and Scheduling Procedures for Macromolecular Proposal Submittal and Scheduling Procedures for Macromolecular Crystallography Beam time for macromolecular crystallography projects is obtained by submitting an SSRL Macromolecular Crystallography Proposal. This proposal is peer reviewed by the Structural Molecular Biology and Biophysics subpanel of the SSRL Proposal Review Panel (PRP) for scientific merit and rating and for criticality of synchrotron radiation use. Proposal Forms New Proposal Request Form (note: you must be a registered user to submit a proposal through our User Portal. Click on "Become a New User" link to register.) Extension Application for Macromolecular Crystallography Proposals Rapid Access Application Form Types of Proposals Proposals should be submitted under one of the following classifications.

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Ray-tracing Procedural Displacement Shaders  

E-Print Network (OSTI)

Displacement maps and procedural displacement shaders are a widely used approach of specifying geometric detail and increasing the visual complexity of a scene. While it is relatively straightforward to handle displacement shaders in pipeline based rendering systems such as the Reyes-architecture, it is much harder to efficiently integrate displacement-mapped surfaces in ray-tracers. Many commercial ray-tracers tessellate the surface into a multitude of small triangles. This introduces a series of problems such as excessive memory consumption and possibly undetected surface detail. In this paper we describe a novel way of ray-tracing procedural displacement shaders directly, that is, without introducing intermediate geometry. Affine arithmetic is used to compute bounding boxes for the shader over any range in the parameter domain. The method is comparable to the direct ray-tracing of B'ezier surfaces and implicit surfaces using B'ezier clipping and interval methods, respectively. Keyw...

Wolfgang Heidrich; Hans-peter Seidel

1998-01-01T23:59:59.000Z

342

Sampling of Procedural Shaders Using Affine Arithmetic  

E-Print Network (OSTI)

Procedural shaders have become popular tools for describing surface reflectance functions and other material properties. In comparison to fixed resolution textures they have the advantage of being resolution independent and storage e#cient. While procedural shaders provide an interface for evaluating the shader at a single point in parameter space, it is not easily possible to obtain an average value of the shader together with accurate error bounds over a finite area. Yet the ability to compute such error bounds is crucial for several interesting applications, most notably hierarchical area sampling for global illumination computations using the finite element approach and for the generation of textures used in interactive computer graphics. Using a#ne arithmetic for evaluating the shader over a finite area yields a tight, conservative error interval for the shader function. Compilers can automatically generate code for utilizing a#ne arithmetic from within shaders implemented in a ...

Heidrich

1996-01-01T23:59:59.000Z

343

Procedure to Measure Indoor Lighting Energy Performance  

SciTech Connect

This document provides standard definitions of performance metrics and methods to determine them for the energy performance of building interior lighting systems. It can be used for existing buildings and for proposed buildings. The primary users for whom these documents are intended are building energy analysts and technicians who design, install, and operate data acquisition systems, and who analyze and report building energy performance data. Typical results from the use of this procedure are the monthly and annual energy used for lighting, energy savings from occupancy or daylighting controls, and the percent of the total building energy use that is used by the lighting system. The document is not specifically intended for retrofit applications. However, it does complement Measurement and Verification protocols that do not provide detailed performance metrics or measurement procedures.

Deru, M.; Blair, N.; Torcellini, P.

2005-10-01T23:59:59.000Z

344

John Bardeen Engineering Leadership Program | Application Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

Application Procedure Application Procedure Candidates must complete these steps and submit by the application deadline. The next application deadline will be February 2014. Complete the online resume profile on the Fermilab employment website here. Submit the following by email or hardcopy to the address listed in the contact information below. Academic/Professional resume or curriculum vitae Abstract of graduate degree thesis Academic transcript (may be a copy; if selected for interview, original will be required) Three (3) letters of reference either sent directly by the writers, or sealed envelopes from the writers and sent by the candidate Statement of research interest Contact information: Bardeen Engineering Leadership Program Fermilab M.S. 340, P.O. Box 500 Batavia, IL 60510 USA

345

Interconnection Testing of Distributed Resources: Preprint  

DOE Green Energy (OSTI)

With the publication of IEEE 1547-2003(TM) Standard for Interconnecting Distributed Resources With Electric Power Systems, the electric power industry has a need to develop tests and procedures to verify that interconnection equipment meets 1547 technical requirements. A new standard, IEEE P1547.1(TM), is being written to give detailed tests and procedures for confirming that equipment meets the interconnection requirements. The National Renewable Energy Laboratory has been validating test procedures being developed as part of IEEE P1547.1. As work progresses on the validation of those procedures, information and test reports are passed on to the working group of IEEE P1547.1 for future revisions.

Kroposki, B.; Basso, T.; DeBlasio, R.

2004-02-01T23:59:59.000Z

346

TRUPACT-II procedures and maintenance instructions  

Science Conference Proceedings (OSTI)

The purpose of this document is to provide the technical requirements for operation, inspection and maintenance of a TRUPACT-II Shipping Package and directly related components. This document shall supply the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP) and Certificate of Compliance (C of C) 9218. In the event there is a conflict between this document and the TRUPACT-II SARP (NRC Certificate of Compliance No. 9218), the TRUPACT-II SARP shall govern. This document details the operations, maintenance, repair, replacement of components, as well as the documentation required and the procedures to be followed to maintain the integrity of the TRUPACT-II container. These procedures may be modified for site use, but as a minimum all parameters and format listed herein must be included in any site modified version. For convenience and where applicable steps may be performed out of sequence. Packaging and payload handling equipment and transport trailers have been specifically designed for use with the TRUPACT-II Packaging. This document discusses the minimum required procedures for use of the adjustable center of gravity lift fixture and the TRUPACT-II transport trailer in conjunction with the TRUPACT-II Packaging.

NONE

1994-01-14T23:59:59.000Z

347

The attractor mechanism as a distillation procedure  

E-Print Network (OSTI)

In a recent paper it has been shown that for double extremal static spherically symmetric BPS black hole solutions in the STU model the well-known process of moduli stabilization at the horizon can be recast in a form of a distillation procedure of a three-qubit entangled state of GHZ-type. By studying the full flow in moduli space in this paper we investigate this distillation procedure in more detail. We introduce a three-qubit state with amplitudes depending on the conserved charges the warp factor, and the moduli. We show that for the recently discovered non-BPS solutions it is possible to see how the distillation procedure unfolds itself as we approach the horizon. For the non-BPS seed solutions at the asymptotically Minkowski region we are starting with a three-qubit state having seven nonequal nonvanishing amplitudes and finally at the horizon we get a GHZ state with merely four nonvanishing ones with equal magnitudes. The magnitude of the surviving nonvanishing amplitudes is proportional to the macroscopic black hole entropy. A systematic study of such attractor states shows that their properties reflect the structure of the fake superpotential. We also demonstrate that when starting with the very special values for the moduli corresponding to flat directions the uniform structure at the horizon deteriorates due to errors generalizing the usual bit flips acting on the qubits of the attractor states.

Péter Lévay; Szilárd Szalay

2010-04-14T23:59:59.000Z

348

Attractor mechanism as a distillation procedure  

Science Conference Proceedings (OSTI)

In a recent paper it was shown that for double extremal static spherical symmetric BPS black hole solutions in the STU model the well-known process of moduli stabilization at the horizon can be recast in a form of a distillation procedure of a three-qubit entangled state of a Greenberger-Horne-Zeilinger type. By studying the full flow in moduli space in this paper we investigate this distillation procedure in more detail. We introduce a three-qubit state with amplitudes depending on the conserved charges, the warp factor, and the moduli. We show that for the recently discovered non-BPS solutions it is possible to see how the distillation procedure unfolds itself as we approach the horizon. For the non-BPS seed solutions at the asymptotically Minkowski region we are starting with a three-qubit state having seven nonequal nonvanishing amplitudes and finally at the horizon we get a Greenberger-Horne-Zeilinger state with merely four nonvanishing ones with equal magnitudes. The magnitude of the surviving nonvanishing amplitudes is proportional to the macroscopic black hole entropy. A systematic study of such attractor states shows that their properties reflect the structure of the fake superpotential. We also demonstrate that when starting with the very special values for the moduli corresponding to flat directions the uniform structure at the horizon deteriorates due to errors generalizing the usual bit flips acting on the qubits of the attractor states.

Levay, Peter; Szalay, Szilard [Department of Theoretical Physics, Institute of Physics, Budapest University of Technology and Economics, H-1521 Budapest (Hungary)

2010-07-15T23:59:59.000Z

349

Technical Section: Procedural isotropic stochastic textures by example  

Science Conference Proceedings (OSTI)

Image textures can easily be created using texture synthesis by example. However, creating procedural textures is much more difficult. This is unfortunate, since procedural textures have significant advantages over image textures. In this paper we address ... Keywords: Isotropic stochastic texture, Noise, Procedural noise, Procedural texture, Solid texture, Stochastic modeling, Texture synthesis by example, Texture synthesis/analysis, Wavelet noise

Ares Lagae; Peter Vangorp; Toon Lenaerts; Philip Dutré

2010-08-01T23:59:59.000Z

350

The Scope of Turing's Analysis of Effective Procedures  

Science Conference Proceedings (OSTI)

Turing's (1936) analysis of effective symbolic procedures is a model of conceptual clarity that plays an essential role in the philosophy of mathematics. Yet appeal is often made to the effectiveness of human procedures in other areas of philosophy. ... Keywords: Turing machine, decision problem, effective procedure, epistemic procedure, philosophy of computation

Jeremy Seligman

2002-05-01T23:59:59.000Z

351

Thermal well-test method  

DOE Patents (OSTI)

A well-test method involving injection of hot (or cold) water into a groundwater aquifer, or injecting cold water into a geothermal reservoir. By making temperature measurements at various depths in one or more observation wells, certain properties of the aquifer are determined. These properties, not obtainable from conventional well test procedures, include the permeability anisotropy, and layering in the aquifer, and in-situ thermal properties. The temperature measurements at various depths are obtained from thermistors mounted in the observation wells.

Tsang, Chin-Fu (Albany, CA); Doughty, Christine A. (Berkeley, CA)

1985-01-01T23:59:59.000Z

352

Nevada Test Site closure program  

SciTech Connect

This report is a summary of the history, design and development, procurement, fabrication, installation and operation of the closures used as containment devices on underground nuclear tests at the Nevada Test Site. It also addresses the closure program mothball and start-up procedures. The Closure Program Document Index and equipment inventories, included as appendices, serve as location directories for future document reference and equipment use.

Shenk, D.P.

1994-08-01T23:59:59.000Z

353

Selected Procedures for Volumetric Calibrations (2012 Ed)  

Science Conference Proceedings (OSTI)

... Analytical glassware should not be dried by ... this should be confirmed by testing the final ... requirements and may have special disposal requirements. ...

2012-05-30T23:59:59.000Z

354

Test Diversity  

E-Print Network (OSTI)

This paper describes a novel method for measuring the degree to which a set of test cases executes a given program in diverse ways with respect to the two fundamental programming concepts: control and data. Test Diversity is a method for measuring the variety of software control flow and data flow, comprising of four new measures: conditional diversity, data diversity, standard deviation of diversity, and test orthogonality. These closely-related measures could be used to evaluate the test effectiveness and the test-effort distribution of a test suite. The Diversity Analyzer is a novel industrial-strength testing tool that can currently perform diversity analysis on software written in C/C++/C#/VB in Windows and.NET environments. The Diversity Analyzer is used to evaluate the fault-detection effectiveness of Test Diversity on various types of industrial projects. Key Words: testing tools, verification, theory, experimentation, conditional diversity, data diversity, standard deviation,

Borislav Nikolik

2006-01-01T23:59:59.000Z

355

Microsoft Word - Records Management Exit Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Records Management Records Management Exit Procedures For Departing Department of Energy Federal and Contractor Employees Records Management Division Office of IT Planning, Architecture, and E-Government Office of the Chief Information Officer July 2010 2 PRESERVATION OF FEDERAL RECORDS The Federal Records Act requires the Department of Energy (DOE) Records Officer to remind departing Federal and contractor employees that Federal records may not be removed from Government custody nor may they be destroyed except in accordance with a records disposition schedule that has been approved by the Archivist of the United States. The creation of adequate documentation and the preservation of Federal records are required by law and regulation

356

Procedure for determining the distribution ranking index  

SciTech Connect

The Distribution Ranking Index (DRI) has been developed as a simple but effective means to indicate the inherent, acute hazards of a material that might be released in a transportation accident. Utilizing existing Dow resources and procedures, it is one of the methods used for prioritization of chemicals in Dow`s distribution related process risk management effort. Seven individual hazard indexes are considered for a material. The values range from 1 to 4 with 4 representing the most severe hazard. The highest value from any hazard index determines the overall DRI. 3 refs., 1 fig., 8 tabs.

Latino, M.A. [Dow Chemical Co., Freeport, TX (United States)

1996-12-31T23:59:59.000Z

357

A procedure for oscillatory parameter identification  

SciTech Connect

A procedure is proposed where a power system is excited with a low-level pseduo-random probing signal and the frequency, damping, magnitude, and shape of oscillatory modes are identified using spectral density estimation and frequency-domain transfer-function identification. Attention is focussed on identifying system modes in the presence of noise. Two examples cases are studied: identification of electromechanical oscillation modes in a 16-machine power system; and turbine-generator shaft modes of a 3-machine power plant feeding a series-compensated 500-kV network.

Trudnowski, D.J.; Donnelly, M.K. [Pacific Northwest Lab., Richland, WA (United States); Hauer, J.F. [Bonneville Power Administration, Portland, OR (United States)

1994-02-01T23:59:59.000Z

358

A procedure of oscillatory parameter identification  

Science Conference Proceedings (OSTI)

A procedure is proposed where a power system is excited with a low-level pseudorandom probing signal and the frequency, damping, magnitude, and shape of oscillatory modes are identified using spectral density estimation and frequency-domain transfer-function identification. Attention is focused on identifying system modes in the presence of noise. Two example cases are studied: identification of electromechanical oscillation modes in a 16-machine power system; and turbine-generator shaft modes of a 3-machine power plant feeding a series-compensated 500-kV network.

Trudnowski, D.J.; Donnelly, M.K. (Pacific Northwest Lab., Richland, WA (United States)); Hauer, J.F. (Bonneville Power Administration, Portland, OR (United States))

1994-11-01T23:59:59.000Z

359

A Quadrotor Test Bench for Six Degree of Freedom Flight  

Science Conference Proceedings (OSTI)

In this paper, a quadrotor test bench that can test and verify the 6 DOF flight controller is presented. The development of controller for aerial vehicle is usually a long and dangerous procedure. It needs series of tests from simulation to real flight. ... Keywords: Flight test, Hardware and software system, Parameter identification, Quadrotor, Test bench, Trajectory linearization control

Yushu Yu; Xilun Ding

2012-12-01T23:59:59.000Z

360

Wilcox formation evaluation; Improved procedures for tight-gas-sand evaluation  

Science Conference Proceedings (OSTI)

This paper discusses risks in tight-gas-sand evaluation, reduced by defining relationships between pore geometry and critical water saturations. These results are integrated with log interpretation to derive an estimated kh that compares favorably with a true kh from production tests. These procedures are potentially applicable for evaluating other complex reservoirs.

Lewis, D.J.; Perrin, J.D. (BP Exploration Inc., Houston, TX (US))

1992-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Office of Fossil EnergyDetailed Core Procedures Manual Volume 1 – Core Acquisition  

E-Print Network (OSTI)

This “Core Procedures Manual, Volume 1 ” contains a description of proposed best practices for use during coring operations for the Barrow Gas Hydrate Test Well Program. This document is designed to describe the responsibilities of well site operations personnel, primarily the core acquisition contractor and coring fluids contractor, Weatherford/Omni and Halliburton/Baroid

Barrow Gas Fields

2009-01-01T23:59:59.000Z

362

GF5 / ROBO Test or ASTM Sequence IIIGA Test, ASTM D7528 Aged Oil LowTemperature Viscosity  

E-Print Network (OSTI)

GF5 / ROBO Test or ASTM Sequence IIIGA Test, ASTM D7528 Aged Oil LowTemperature Viscosity SPECIFICATIONS PROCEDURE PARAMETERS The ROBO test is a proposed test for performance category GF.5, ASTM D7528. The ASTM Sequence IIIGA Test, ASTM D7320 may be run instead of the above. A total

Chapman, Clark R.

363

PNGV Battery Performance Testing and Analyses  

SciTech Connect

In support of the Partnership for a New Generation of Vehicles (PNGV), the Idaho National Engineering and Environmental Laboratory (INEEL) has developed novel testing procedures and analytical methodologies to assess the performance of batteries for use in hybrid electric vehicles (HEV’s). Tests have been designed for both Power Assist and Dual Mode applications. They include both characterization and cycle life and/or calendar life. At periodic intervals during life testing, a series of Reference Performance Tests are executed to determine changes in the baseline performance of the batteries. Analytical procedures include a battery scaling methodology, the calculation of pulse resistance, pulse power, available energy, and differential capacity, and the modeling of calendar- and cycle-life data. PNGV goals, test procedures, analytical methodologies, and representative results are presented.

Motloch, Chester George; Belt, Jeffrey R; Christophersen, Jon Petter; Wright, Randy Ben; Hunt, Gary Lynn; Sutula, Raymond; Duong, T.Q.; Barnes, J.A.; Miller, Ted J.; Haskind, H. J.; Tartamella, T. J.

2002-03-01T23:59:59.000Z

364

Standard Test Methods for Wet Insulation Integrity Testing of Photovoltaic Modules  

E-Print Network (OSTI)

1.1 These test methods provide procedures to determine the insulation resistance of a photovoltaic (PV) module, i.e. the electrical resistance between the module's internal electrical components and its exposed, electrically conductive, non-current carrying parts and surfaces. 1.2 The insulation integrity procedures are a combination of wet insulation resistance and wet dielectric voltage withstand test procedures. 1.3 These procedures are similar to and reference the insulation integrity test procedures described in Test Methods E 1462, with the difference being that the photovoltaic module under test is immersed in a wetting solution during the procedures. 1.4 These test methods do not establish pass or fail levels. The determination of acceptable or unacceptable results is beyond the scope of these test methods. 1.5 The values stated in SI units are to be regarded as the standard. 1.6 There is no similar or equivalent ISO standard. 1.7 This standard does not purport to address all of the safety conce...

American Society for Testing and Materials. Philadelphia

2007-01-01T23:59:59.000Z

365

Quality Assurance Procedures in the Oklahoma Mesonetwork  

Science Conference Proceedings (OSTI)

High quality data sources are critical to scientists, engineers, and decision makers alike. The models that scientists develop and test with quality-assured data eventually become used by a wider community, from policy makers’ long-term ...

Mark A. Shafer; Christopher A. Fiebrich; Derek S. Arndt; Sherman E. Fredrickson; Timothy W. Hughes

2000-04-01T23:59:59.000Z

366

Laser Controlled Area Standard Operating Procedure (SOP)  

NLE Websites -- All DOE Office Websites (Extended Search)

72 72 2 Effective: Page 1 of 16 3/6/13 Subject: X26C Laser Safety Program Documentation The only official copy of this file is the one on-line in the Photon Sciences website. Before using a printed copy, verify that it is the most current version by checking the document issue date on the Photon Sciences website. 2.1/2g03e011.doc 1 (06/2009) BROOKHAVEN NATIONAL LABORATORY LASER CONTROLLED AREA STANDARD OPERATING PROCEDURE (SOP) This document defines the safety management program for the laser system(s) listed below. All American National Standard Institute (ANSI) Hazard Class 3B and 4 laser systems must be documented, reviewed, and approved through use of this form. Each system must be reviewed annually. Modify the template for this document to fit your particular circumstance.

367

Laser Controlled Area Standard Operating Procedure (SOP)  

NLE Websites -- All DOE Office Websites (Extended Search)

6 4 6 4 Effective: Page 1 of 18 09/16/2011 Subject: Laser Safety Program Documentation: U2A The only official copy of this file is the one on-line in the PS ESH website. Before using a printed copy, verify that it is the most current version by checking the document issue date on the PS ESH website. BROOKHAVEN NATIONAL LABORATORY LASER CONTROLLED AREA STANDARD OPERATING PROCEDURE (SOP) U2A Laser Systems This document defines the safety management program for the laser system(s) listed below. All American National Standard Institute (ANSI) Hazard Class 3B and 4 laser systems must be documented, reviewed, and approved through use of this form. Each system must be reviewed annually. System description: There are 4 lasers installed at beamline U2A for diamond anvil cell experiments:

368

Laser Controlled Area Standard Operating Procedure (SOP)  

NLE Websites -- All DOE Office Websites (Extended Search)

90 90 1 Effective: Page 1 of 11 06/20/12 Subject: Laser Safety Program Documentation - Raman X18/19 Frenkel Group 3.1/2g03e011.doc 1 (02/2010) BROOKHAVEN NATIONAL LABORATORY LASER CONTROLLED AREA STANDARD OPERATING PROCEDURE (SOP) This document defines the safety management program for the laser system(s) listed below. All American National Standard Institute (ANSI) Hazard Class 3B and 4 laser systems must be documented, reviewed, and approved through use of this form. Each system must be reviewed annually. Modify the template for this document to fit your particular circumstance. System description: Raman fiber optic system with class 3B laser source Location: Currently in NSLS room 1-127, but will be utilized with beamlines X18A, X18B, and X19A

369

Radiation Safety Policy and Procedures Committee  

NLE Websites -- All DOE Office Websites (Extended Search)

RSPPC Meeting Minutes APS only RSPPC Meeting Minutes APS only Radiation Safety Policy and Procedures Committee Charter 1. Purpose The committee reviews functional changes to the Access Control Interlock System (ACIS) and Personnel Protection System (PSS) used to provide personnel protection and area exclusion related to APS accelerators, storage ring and other radiation handling areas. The RSPP Committee advises APS management on radiation safety matters. At the request of APS Management the committee reviews projects, recommends radiation safety policy, and evaluates accident investigation conclusions. 2. Membership Members are appointed by the APS Division Directors and APS Director for their knowledge and background in Interlock Systems, Radiation Safety, Accelerator Operations and Work on the Experiment Floor.

370

Laser Controlled Area Standard Operating Procedure (SOP)  

NLE Websites -- All DOE Office Websites (Extended Search)

PS-ESH-0025 PS-ESH-0025 01 Effective: Page 1 of 13 03/09/2012 Subject: Laser Safety Program Documentation X17C The only official copy of this file is the one on-line in the NSLS ESH website. Before using a printed copy, verify that it is the most current version by checking the document issue date on the NSLS ESH website. BROOKHAVEN NATIONAL LABORATORY LASER CONTROLLED AREA STANDARD OPERATING PROCEDURE (SOP) X17C Laser System System description: There is one laser at X17C: Diode-Pumped Solid State Laser (Class 3B) that has two uses: - Measurement of diamond anvil pressure from ruby fluorescence - Raman spectrum measurements Location: The DPSS laser system is located in NSLS room 1-134C LINE MANAGEMENT RESPONSIBILITIES The Owner/Operator for this laser is listed below. The Owner/Operator is the Line Manager of the system

371

Laser Controlled Area Standard Operating Procedure (SOP)  

NLE Websites -- All DOE Office Websites (Extended Search)

3 3 001 Effective: Page 1 of 11/18/11 11 Subject: Laser Safety Program Documentation Bldg 703 E3/E4 3.1/2g03e011.doc 1 (02/2010) BROOKHAVEN NATIONAL LABORATORY LASER CONTROLLED AREA STANDARD OPERATING PROCEDURE (SOP) This document defines the safety management program for the laser system(s) listed below. All American National Standard Institute (ANSI) Hazard Class 3B and 4 laser systems must be documented, reviewed, and approved through use of this form. Each system must be reviewed annually. Modify the template for this document to fit your particular circumstance. System description: MOS laser curvature measurement system - Thin Film Deposition Lab Location: 703, E2/E4 LINE MANAGEMENT RESPONSIBILITIES The Owner/Operator(s) for this laser is/are listed below. The Owner/Operator is the Line Manager of the

372

Laser Controlled Area Standard Operating Procedure (SOP)  

NLE Websites -- All DOE Office Websites (Extended Search)

79 79 01 Effective: Page 1 of 17 05/13/11 Subject: X17B3 Laser Safety Program Documentation 1 AUTHORIZATION | Princeton University BROOKHAVEN NATIONAL LABORATORY LASER CONTROLLED AREA STANDARD OPERATING PROCEDURE (SOP) This document defines the safety management program for the laser system listed below. All American National Standard Institute (ANSI) Hazard Class 3B and 4 laser systems must be documented, reviewed, and approved through use of this form. Each system must be reviewed annually. System description: A laser heating system for diamond anvil cell experiments has been installed at X17B3. A class 4 ytterbium fiber laser (IPG model YLR-100-SM-CS) is used to perform high-pressure laser heating of samples contained in diamond anvil cells. Included within this laser is a guide laser

373

Patent Protection and Licensing Procedure | BNL Technology  

NLE Websites -- All DOE Office Websites (Extended Search)

BNL Inventors BNL Inventors Patent Protection and Licensing Procedure TCP Staff Assignment - Invention Disclosures received by Intellectual Property Legal Group (IPLG) will be given a BNL number, and assigned to a specific TCP staff member for commercial assessment. Henceforth, the assigned staff member will be responsible for all commercialization actions relating to the docket. Assessment - The TCP staff member assigned to the docket will meet with the inventor(s). Together they will discuss the invention and make a preliminary evaluation of potential applications and possible markets. Based on commercial assessment and a preliminary novelty determination, the TCP staff will make a recommendation to the IPLG whether to patent the invention. The TCP's decision and relevant documents will be circulated

374

PARS II Standard Operating Procedure Business Rules  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

June 25, 2011 June 25, 2011 U.S. Department of Energy The PARS II Standard Operating Procedure is a "living document" and will be updated on an ongoing basis. Comments or suggestions are welcome and should be forwarded to the PARS II administrator at PARSIIsupportoecm@hq.doe.gov. Notes Comment Pages Comment Pages Index Screenshot Pages Introduction I-1 Generic Business Rules I-2 Select Project I-3 - I-5 Enter/Modify Project Information I-6 - I-15 Enter/Modify Contact Information I-16 - I-21 Creating a Project I-22 Enter CD0 Information I-23 - I-26 Enter CD1 Information I-27 - I-29 Enter CD2 Information I-30 - I-33 Enter CD3A Information I-34 - I-36 Enter CD3 Information I-37 - I-39 Enter CD4 Information I-40 - I-42 Enter Closeout Information I-43 - I-45 Enter BCP Information I-46 - I-50 Screenshot

375

Data Validation Procedure for Chemical Analysis  

E-Print Network (OSTI)

This report has been reproduced from the best available copy. Available in paper copy and microfiche. Available for a process ing fee to U.S. Department of Energy and its contractors from: U.S. Department of Energy Office of Scientific and Technical Information P.O. Box 62 Oak Ridge, TN 37831-0062 (865) 576-8401 fax: (865) 576-5728 email: reports@adonis.osti.gov online ordering: http://www.doe.gov/bridge Available for sale to the public, in paper, from: U.S. Department of Commerce National Technical Information Service 5285 Port Royal Road Springfield, VA 22161 (800) 553-6847 fax: (703) 605.6900 email: orders@ntis.fedworld.gov online ordering: http://www.ntis.gov/ordering.htm Printed in the United States of America DISCLM-5.CHP (11/99) BHI-01435 Rev. 0 Data Validation Procedure for Chemical Analysis Author

Uhsduhg Ir Uhsduhg

2000-01-01T23:59:59.000Z

376

Laser Controlled Area Standard Operating Procedure (SOP)  

NLE Websites -- All DOE Office Websites (Extended Search)

32 32 004 Effective: Page 1 of 13 12/1/10 Subject: Laser Safety Program Documentation X20C 3.1/2g03e011.doc 1 (02/2010) BROOKHAVEN NATIONAL LABORATORY LASER CONTROLLED AREA STANDARD OPERATING PROCEDURE (SOP) This document defines the safety management program for the laser system(s) listed below. All American National Standard Institute (ANSI) Hazard Class 3B and 4 laser systems must be documented, reviewed, and approved through use of this form. Each system must be reviewed annually. Modify the template for this document to fit your particular circumstance. System description: Time-resolved light scattering Location: X20C Hutch LINE MANAGEMENT RESPONSIBILITIES The Owner/Operator(s) for this laser is/are listed below. The Owner/Operator is the Line Manager of the

377

QualityAssurance&Testing  

NLE Websites -- All DOE Office Websites (Extended Search)

and Testing and Testing Manufacturing Technologies The Manufacturing Science & Technology Center provides customers with manufacturing quality requirements, testing standards and specifica- tions for new product designs, including the implementation of these requirements into final product acceptance complete with documenta- tion. Technical support and procedures are fur- nished for Interagency Product Acceptance. Capabilities * Will inspect printed circuit (PC) boards, wire wrap boards, boxes, chassis, cables, racks, systems, etc. * Work from sketches or formal drawings * Review drawings and requirements * Visual inspections for layout, markings, solder joints, components, mechanical assembly, general workmanship, safety * Point-to-point continuity checks

378

Chapter 31 - Contract Cost Principles and Procedures | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 - Contract Cost Principles and Procedures Chapter 31 - Contract Cost Principles and Procedures 31.1CostReasonableness0.pdf 31.2AllowableFoodandBeverageCostsatDOEandCo...

379

TESTING TECHNIQUE  

Science Conference Proceedings (OSTI)

... The cooling bath should ... When testing super-high energy level specimens ... upon the resolution of the scale or readout device at the low end and the ...

2012-10-09T23:59:59.000Z

380

Test Methods  

Science Conference Proceedings (OSTI)

... of the robot, operator control unit (OCU), payload, and batteries • Tools needed ... this test method is to quantitatively evaluate the battery capacity per ...

2010-10-05T23:59:59.000Z

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

NREL Documents Efficiency of Mini-Split Heat Pumps (Fact Sheet...  

NLE Websites -- All DOE Office Websites (Extended Search)

MSHPs for any building and climate. Some conclusions comparing the tested units to high-SEER (Seasonal Energy Efficiency Ratio) staged systems are also provided. Potential Impact...

382

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... The method allows calculation of capacity at 95DG F rating point and seasonal energy efficiency ratio, SEER, without performing laboratory test of ...

383

Publications Portal  

Science Conference Proceedings (OSTI)

... and seasonal energy efficiency ratio, SEER, of outdoor unit and indoor unit air-conditioner combinations not previously tested as a comple ... ...

2012-09-17T23:59:59.000Z

384

Records Management Procedures for Storage, Transfer and Retrieval...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

procedures, and essential transactions, including record material containing evidence or information appropriate for preservation because of its administrative, legal,...

385

Model Recovery Procedure for Response to a Radiological Transportation...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

for Response to a Radiological Transportation Incident Model Recovery Procedure for Response to a Radiological Transportation Incident This Transportation Emergency...

386

Comparative evaluation of two extraction procedures: The TCLP and the ep. Final report  

Science Conference Proceedings (OSTI)

The 1984 amendments to the Resource Conservation and Recovery Act (RCRA) require that the U.S. Environmental Protection Agency (EPA) restrict the land disposal of hazardous wastes. The EPA has identified four characteristics that could be used to classify a waste as hazardous: corrosivity, ignitability, reactivity, and toxicity. A waste exhibiting any one of these properties is classified as hazardous. The Extraction Procedure Toxicity Characteristic (EP) test is used to determine if a waste poses an unacceptable risk to ground water if improperly managed and therefore should be managed as a hazardous waste. Regulatory thresholds, based on the EP test, have been established for eight metals, four pesticides, and two herbicides. The Toxicity Characteristic Leaching Procedure (TCLP EPA Method 1311) was developed to address a Congressional mandate to identify additional characteristics of wastes, primarily organic constituents that may pose a threat to the environment. The TCLP has been promulgated for use in determining specific treatment standards associated with the land disposal restrictions of RCRA. The TCLP has also been proposed as a replacement procedure for the EP test. Using the TCLP procedure, the EPA has also proposed to expand with hazardous waste regulatory levels the list of contaminants from the 14 listed in the EP protocol to a total of 52. The additional contaminants include 20 volatile organics, 16 semivolatile organics, and 2 pesticides. The purpose of this study was to compare the results of the TCLP with those of the EP.

Bricka, R.M.; Holmes, T.T.; Cullinane, M.J.

1992-10-01T23:59:59.000Z

387

Railcar waste transfer system hydrostatic test  

SciTech Connect

Recent modifications have been performed on the T-Plant Railcar Waste Transfer System, This Acceptance Test Procedure (ATP) has been prepared to demonstrate that identified piping welds and mechanical connections incorporated during the modification are of high integrity and are acceptable for service. This will be achieved by implementation of a hydrostatic leak test.

Ellingson, S.D.

1997-03-31T23:59:59.000Z

388

Injectivity Testing for Vapour Dominated Feed Zones  

DOE Green Energy (OSTI)

Wells with vapor dominated feed zones yield abnormal pressure data. This is caused by the condensation of vapor during water injection. A revised injectivity test procedure currently applied by PNOC at the Leyte Geothermal Power Project has improved the injectivity test results.

Clotworthy, A.W.; Hingoyon, C.S.

1995-01-01T23:59:59.000Z

389

Hydrogen/CNG Blended Fuels Performance Testing in a Ford F-150  

NLE Websites -- All DOE Office Websites (Extended Search)

Attachment 1 Procedure ETA-YTP001 Revision 0 Attachment 1 - Hydrogen ICE Vehicle Acceleration Test Procedure ETA-YTP001 Revision 0 Effective May 15, 2003 Implementation of SAE...

390

ACOUSTICAL TESTING SERVICES TEST METHOD ...  

Science Conference Proceedings (OSTI)

... IEC 60704-2-3 Household and similar electrical appliances - Test code for ... noise emitted and structure-borne vibration induced by small air- moving ...

2013-05-06T23:59:59.000Z

391

Reporting Cooperating Agencies in Implementing the Procedural Requirements  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Reporting Cooperating Agencies in Implementing the Procedural Reporting Cooperating Agencies in Implementing the Procedural Requirements of the National Environmental Policy Act Reporting Cooperating Agencies in Implementing the Procedural Requirements of the National Environmental Policy Act The purpose of this Council on Environmental Quality Memorandum is to establish a revised report to ensure that all Federal agencies are consistently reporting designation of Federal and non-federal cooperating agencies in the preparation of analyses and documentation required by the National Environmental Policy Act (NEPA). REPORTING COOPERATING AGENCIES IN IMPLEMENTING THE PROCEDURAL REQUIREMENTS OF THE NATIONAL ENVIRONMENTAL POLICY ACT More Documents & Publications Cooperating Agencies in Implementing the Procedural Requirements of the

392

Reporting Cooperating Agencies in Implementing the Procedural Requirements  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Reporting Cooperating Agencies in Implementing the Procedural Reporting Cooperating Agencies in Implementing the Procedural Requirements of the National Environmental Policy Act Reporting Cooperating Agencies in Implementing the Procedural Requirements of the National Environmental Policy Act The purpose of this Council on Environmental Quality Memorandum is to establish a revised report to ensure that all Federal agencies are consistently reporting designation of Federal and non-federal cooperating agencies in the preparation of analyses and documentation required by the National Environmental Policy Act (NEPA). REPORTING COOPERATING AGENCIES IN IMPLEMENTING THE PROCEDURAL REQUIREMENTS OF THE NATIONAL ENVIRONMENTAL POLICY ACT More Documents & Publications Cooperating Agencies in Implementing the Procedural Requirements of the

393

Hazardous Materials Incident Response Procedure | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hazardous Materials Incident Response Procedure Hazardous Materials Incident Response Procedure Hazardous Materials Incident Response Procedure The purpose of this procedure is to provide guidance for developing an emergency response plan, as outlined in OSHA's 29 CFR 1910.120(q), for facility response. This model has been adopted and applied to work for response to transportation accidents involving radioactive material or other hazardous materials incidents Hazardous Materials Incident Response Procedure.docx More Documents & Publications Handling and Packaging a Potentially Radiologically Contaminated Patient Decontamination Dressdown at a Transportation Accident Involving Radioactive Material Medical Examiner/Coroner on the Handling of a Body/Human Remains that are Potentially Radiologically Contaminated

394

Eder Acquisition 2007 Habitat Evaluation Procedures Report.  

DOE Green Energy (OSTI)

A habitat evaluation procedures (HEP) analysis was conducted on the Eder acquisition in July 2007 to determine how many protection habitat units to credit Bonneville Power Administration (BPA) for providing funds to acquire the project site as partial mitigation for habitat losses associated with construction of Grand Coulee and Chief Joseph Dams. Baseline HEP surveys generated 3,857.64 habitat units or 1.16 HUs per acre. HEP surveys also served to document general habitat conditions. Survey results indicated that the herbaceous plant community lacked forbs species, which may be due to both livestock grazing and the late timing of the surveys. Moreover, the herbaceous plant community lacked structure based on lower than expected visual obstruction readings (VOR); likely a direct result of livestock impacts. In addition, introduced herbaceous vegetation including cultivated pasture grasses, e.g. crested wheatgrass and/or invader species such as cheatgrass and mustard, were present on most areas surveyed. The shrub element within the shrubsteppe cover type was generally a mosaic of moderate to dense shrubby areas interspersed with open grassland communities while the 'steppe' component was almost entirely devoid of shrubs. Riparian shrub and forest areas were somewhat stressed by livestock. Moreover, shrub and tree communities along the lower reaches of Nine Mile Creek suffered from lack of water due to the previous landowners 'piping' water out of the stream channel.

Ashley, Paul R.

2008-01-01T23:59:59.000Z

395

Recommendations for reducing ambiguity in written procedures.  

SciTech Connect

Previous studies in the nuclear weapons complex have shown that ambiguous work instructions (WIs) and operating procedures (OPs) can lead to human error, which is a major cause for concern. This report outlines some of the sources of ambiguity in written English and describes three recommendations for reducing ambiguity in WIs and OPs. The recommendations are based on commonly used research techniques in the fields of linguistics and cognitive psychology. The first recommendation is to gather empirical data that can be used to improve the recommended word lists that are provided to technical writers. The second recommendation is to have a review in which new WIs and OPs and checked for ambiguities and clarity. The third recommendation is to use self-paced reading time studies to identify any remaining ambiguities before the new WIs and OPs are put into use. If these three steps are followed for new WIs and OPs, the likelihood of human errors related to ambiguity could be greatly reduced.

Matzen, Laura E.

2009-11-01T23:59:59.000Z

396

Nevada Test Site FFCA Consent Order, March 27, 1996 Summary  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Test Site Federal Facility Compliance Act Test Site Federal Facility Compliance Act Consent Order, March 27, 1996 State Nevada Agreement Type Consent Order Legal Driver(s) FFCAct Scope Summary Enforce the STP and establish procedures for reviewing schedules, deleting waste streams, and administrative procedures Parties DOE; Nevada Division of Environmental Protection Date 3/27/1996 SCOPE * Require DOE to achieve compliance with the requirements of the FFCAct through the STP which contains schedules and applicable strategies for achieving compliance with the applicable LDR standards. * Establish procedures for reviewing schedules, deleting waste streams, and administrative procedures. * Establish enforceable schedules and milestones applicable to this Order. ESTABLISHING MILESTONES *

397

test | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

test test test test More Documents & Publications Software Testing Checklist February2GuidanceMemorandum.pdf Site Transition Plan Guidance...

398

Past DOE Technical Standards Program Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Past DOE Technical Standards Program Procedures Past DOE Technical Standards Program Procedures Past DOE Technical Standards Program Procedures TSPP July 2009 September 26, 2009 DOE-TSPP-0, Technical Standards Program Procedures - July 1, 2009 This document is the summary page for all of the DOE Technical Standards Program Procedures. August 26, 2009 DOE-TSPP-1, Technical Standards Program Responsibilities - July 1, 2009 This procedure describes the responsibilities of persons who are charged with implementing the DOE Technical Standards Program. August 26, 2009 DOE-TSPP-2, Establishing the Need for a Technical Standard - July 1, 2009 This procedure provides guidance for the routine maintenance of DOE Technical Standards. August 26, 2009 DOE-TSPP-3, Use of Non-Government Standards and Interaction with Non-Government Standards Bodies - July 1, 2009

399

CRAD, Verification and Validation of Facilities Procedures Assessment Plan  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Verification and Validation of Facilities Procedures Verification and Validation of Facilities Procedures Assessment Plan CRAD, Verification and Validation of Facilities Procedures Assessment Plan Performance Objective: The purpose of this assessment is verify and validate the process for the development of operations procedures and that procedures are in place which provide direction to personnel to ensure that the facility is operated within its design bases. Criteria: Operations procedures should be written to provide specific direction for operating systems and equipment during normal and postulated abnormal and emergency conditions. (DOE O 5480.19 A) Operations procedures should provide appropriate direction to ensure that the facility is operated within its design bases and should be effectively used to support safe operations of the facility. (DOE O

400

A prototype on-line work procedure system for radioisotope thermoelectric generator production  

DOE Green Energy (OSTI)

An on-line system to manage work procedures is being developed to support radioisotope thermoelectric generator (RTG) assembly and testing in a new production facility. This system implements production work procedures as interactive electronic documents executed at the work site with no intermediate printed form. It provides good control of the creation and application of work procedures and provides active assistance to the worker in performing them and in documenting the results. An extensive prototype of this system is being evaluated to ensure that it will have all the necessary features and that it will fit the user's needs and expectations. This effort has involved the Radioisotope Power Systems Facility (RPSF) operations organization and technology transfer between Westinghouse Hanford Company (Westinghouse Hanford) and EG G Mound Applied Technologies Inc. (Mound) at the US Department of Energy (DOE) Mound Site. 1 ref.

Kiebel, G.R.

1991-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Acceptance Test Report for AMS-4 Continuous Air Monitors (CAM) at 241AN Exhausters  

SciTech Connect

This report provides the completed copy and test results of the Acceptance Test Procedure (TWR-4713). Test results were actually hand written in the ATP including redline changes. All acceptance criteria steps were completed satisfactorily without exceptions.

SCAIEF, C.C.

1999-11-11T23:59:59.000Z

402

Test plan  

U.S. Energy Information Administration (EIA)

3.0 TEST PLAN METHODOLOGY 8. 3.1 Assumptions 8. 3.2 Methodology 8. 4.0 COMMENTS ON INITIAL VIEW OF THE DATA 16 1.0 INTRODUCTION. EIA tasked Allied ...

403

Distributed Power Program DER Pilot Test at the Nevada Test Site  

SciTech Connect

The DOE Distributed Power Program conducted a pilot test of interconnection test procedures November 12-16, 2001 at Area 25 of the Nevada Test Site (NTS). The objective of this pilot test was to respond to Congressional direction in the Energy and Water Development Appropriations Act of 2001 to complete a distributed power demonstration at the Nevada Test Site and validated interconnection tests in the field. The demonstration consisted of field verification of tests in IEEE P1547 (Draft 7) that are required for interconnection of distributed generation equipment to electrical power systems. Some of the testing has been conducted in a laboratory setting, but the Nevada Test Site provided a location to verify the interconnection tests in the field. The testing also provided valuable information for evaluating the potential for the Nevada Test Site to host future field-testing activities in support of Distributed Energy Resources System Integration R&D.

Kroposki, B.; DeBlasio, R.; Galdo, J.

2002-05-01T23:59:59.000Z

404

K West basin isolation barrier leak rate test  

SciTech Connect

This document establishes the procedure for performing the acceptance test on the two isolation barriers being installed in K West basin. This acceptance test procedure shall be used to: First establish a basin water loss rate prior to installation of the two isolation barriers between the main basin and the discharge chute in K-Basin West. Second, perform an acceptance test to verify an acceptable leakage rate through the barrier seals.

Whitehurst, R.; McCracken, K.; Papenfuss, J.N.

1994-10-31T23:59:59.000Z

405

Acceptance test report 2721-Z upgrades  

SciTech Connect

This test procedure provides instructions for acceptance testing of modifications to the 2721-Z diesel-generator system made by Project C-189. The modifications include (1) replacing the generator NUMA-LOGIC controller with connection to the PFP distributed control system (DCS), (2) replacing ATSI with a breaker switching scheme for 2736-ZB backup power and (3) providing a method for generator load and system testing.

Keck, R.D.

1998-02-03T23:59:59.000Z

406

Sensitivity testing of liquid high explosives  

SciTech Connect

This article describes a test procedure for a liquid high explosive. The liquid to be tested is NTN, a mixture of nitromethane, tetranitomethane, and 1-nitropropane in 52, 33.3, and 14.7 weight per cent. The test is to study the sensitivity of the explosive to shock by firing it in projectiles from a M1A1 155mm howlitzer, with a charge such that it will not exceed 16,500 g`s acceleration.

O`Connell, L.

1961-01-31T23:59:59.000Z

407

Standard Operating Procedure (SOP) for MTS Single Acting Frame With UniTest  

E-Print Network (OSTI)

REMOVING COVERS FOR TROUBLESHOOTING PURPOSES. WARNING: NEVER PLACE BODY PARTS BETWEEN POTENTIAL PINCH

Thompson, Michael

408

Test Procedure for §170.306 (d)(1) Electronic Copy of Health ...  

Science Conference Proceedings (OSTI)

... Vendor-supplied (eg, Medical Record Number) Vendor-supplied (eg, 540 Granite Street, Blanchard, Oklahoma 73010 405-228-7744) ...

2010-09-24T23:59:59.000Z

409

Test Procedure for §170.306 (d)(1) Electronic Copy of Health ...  

Science Conference Proceedings (OSTI)

... Phillip Jones 03/08/1962 14:25:50 Male 998777349 Medical Record Number 540 Granite Street, Blanchard, Oklahoma 73010 405-228-7744 ...

2010-08-13T23:59:59.000Z

410

Design and Flight Demonstration Test of a Continuous Descent Approach Procedure for Louisville International Airport  

E-Print Network (OSTI)

A design methodology based on the principles of system analysis was used to design a noise abatement

Clarke, John-Paul

411

Test Procedure for §170.306 (d)(2) Electronic Copy of Health ...  

Science Conference Proceedings (OSTI)

... the capability to create a copy of a patient's discharge summary in human ... to her ankle after an episode of syncope with no loss of consciousness. ...

2010-09-24T23:59:59.000Z

412

Nondestructive Evaluation: Procedure for Manual Phased Array Ultrasonic Testing (UT) of Dissimilar Metal Welds (DMW)  

Science Conference Proceedings (OSTI)

Dissimilar metal weld (DMW) piping joints in nuclear power plants must be examined periodically using ultrasonic examination technology. Phased array ultrasonic technology has recently become available in a handheld, portable configuration. This technology could increase the speed of the examinations, save costs, reduce radiation exposure, and decrease the cost and difficulty of qualifying personnel to perform the examination. The Electric Power Research Institute (EPRI) recently developed an ultrasonic ...

2008-09-16T23:59:59.000Z

413

Validating simulation tools for vehicle system studies using advanced control and testing procedure.  

DOE Green Energy (OSTI)

Hybrid electric vehicles (HEVs) offer the potential to increase propulsion system efficiency and decrease pollutant emissions relative to conventional vehicles. The US Department of Energy (DOE) and the auto industry are developing HEV technology as part of the Partnership for a New Generation of Vehicles (PNGV) program. Argonne National Laboratory (ANL) supports the DOE in this program by contributing to technical target setting and evaluating new technologies in a vehicle systems context. In this role, ANL has developed a unique set of interrelated tools and facilities to analyze, develop, and validate components and propulsion systems in a vehicle environment.

Pasquier, M.; Duoba, M.; Rousseau, A.

2001-09-12T23:59:59.000Z

414

Status report on ESF-related prototype testing  

Science Conference Proceedings (OSTI)

This report provides information on the Prototype Testing performed in the G-Tunnel on the Nevada Test Site by the Yucca Mountain Project form April 1988 to November 1989. The Testing Program was implemented to ensure that the Exploratory Shaft Facility (ESF) tests can be completed in the time available and to develop instruments, equipment, and procedures so the ESF tests can collect reliable and representative site characterization data. This report summarizes the ESF prototype tests and presents preliminary results.

Oliver, R.D.; Kalia, H.N. [comps.

1992-12-01T23:59:59.000Z

415

In-place HEPA filter penetration test  

SciTech Connect

We have demonstrated the feasibility of conducting penetration tests on high efficiency particulate air (HEPA) filters as installed in nuclear ventilation systems. The in-place penetration test, which is designed to yield equivalent penetration measurements as the standard DOP efficiency test, is based on measuring the aerosol penetration of the filter installation as a function of particle size using a portable laser particle counter. This in-place penetration test is compared to the current in-place leak test using light scattering photometers for single HEPA filter installations and for HEPA filter plenums using the shroud method. Test results show the in-place penetration test is more sensitive than the in-place leak test, has a similar operating procedure, but takes longer to conduct. Additional tests are required to confirm that the in-place penetration test yields identical results as the standard dioctyl phthalate (DOP) penetration test for HEPA filters with controlled leaks in the filter and gasket and duct by-pass leaks. Further development of the procedure is also required to reduce the test time before the in- place penetration test is practical.

Bergman, W.; Wilson, kK.; Elliott, J.; Bettencourt, B.; Slawski, J.W.

1997-01-01T23:59:59.000Z

416

Thermal well-test method  

DOE Patents (OSTI)

A well-test method involving injection of hot (or cold) water into a groundwater aquifer, or injecting cold water into a geothermal reservoir is disclosed. By making temperature measurements at various depths in one or more observation wells, certain properties of the aquifer are determined. These properties, not obtainable from conventional well test procedures, include the permeability anisotropy, and layering in the aquifer, and in-situ thermal properties. The temperature measurements at various depths are obtained from thermistors mounted in the observation wells.

Tsang, C.F.; Doughty, C.A.

1984-02-24T23:59:59.000Z

417

Exact test for Markov order  

E-Print Network (OSTI)

We describe an exact test of the null hypothesis that a Markov chain is nth order versus the alternate hypothesis that it is $(n+1)$-th order. The procedure does not rely on asymptotic properties, but instead builds up the test statistic distribution via surrogate data and is valid for any sample size. Surrogate data are generated using a novel algorithm that guarantees, per shot, a uniform sampling from the set of sequences that exactly match the nth order properties of the observed data.

Pethel, Shawn D

2013-01-01T23:59:59.000Z

418

Testing technology  

SciTech Connect

This bulletin from Sandia National Laboratories presents current research highlights in testing technology. Ion microscopy offers new nondestructive testing technique that detects high resolution invisible defects. An inexpensive thin-film gauge checks detonators on centrifuge. Laser trackers ride the range and track helicopters at low-level flights that could not be detected by radar. Radiation transport software predicts electron/photon effects via cascade simulation. Acoustic research in noise abatement will lead to quieter travelling for Bay Area Rapid Transport (BART) commuters.

Not Available

1993-10-01T23:59:59.000Z

419

Code of Federal Regulations Procedural Rules for DOE Nuclear Activities  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Code of Federal Regulations Procedural Rules for DOE Nuclear Code of Federal Regulations Procedural Rules for DOE Nuclear Activities Part II Code of Federal Regulations Procedural Rules for DOE Nuclear Activities Part II The Department of Energy (DOE) is issuing procedural rules to be used in applying its substantive regulations and orders relating to nuclear safety. These procedural rules are intended to be an essential part of the framework through which DOE deals with its contractors, subcontractors, and suppliers to ensure its nuclear facilities are operated in a manner that protects public and worker safety and the environment. In particular, this part sets forth the procedures to implement the provisions of the Price- Anderson Amendments Act of 1988 (PAAA) which subjects DOE contractors to potential civil and criminal penalties for violations of DOE rules,

420

Procedures for Public Release of Data | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Procedures for Public Release of Data Procedures for Public Release of Data Procedures for Public Release of Data Procedures for Public Release of Data All Department of Energy (DOE) data owners should follow the procedures outlined below in preparing a data collection for public release. Legislative requirements, Office of Management and Budget (OMB) guidance, and DOE directives related to data quality and data control are referenced in the procedures steps. Step 1 Data owners and/or managers identify a data collection for possible public release. The following initial reviews are performed at the Administration or Program Office level by data owners in conjunction with appropriate staff (classifiers, records managers, privacy managers, and General Counsel among others) to determine if the data collection is

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Unified Procedures Applicable to Major Federal Actions Relating to Nuclear  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Unified Procedures Applicable to Major Federal Actions Relating to Unified Procedures Applicable to Major Federal Actions Relating to Nuclear Activities Subject to Executive Order 12114 (State Department, 44 Fed Reg 65560) Unified Procedures Applicable to Major Federal Actions Relating to Nuclear Activities Subject to Executive Order 12114 (State Department, 44 Fed Reg 65560) The following unified procedures issued by the State Department are established to satisfy the requirement of the Executive Order for implementing procedures concerning nuclear export activities of Federal agencies. 44 Fed Reg 65560: Department of State: Unified Procedures Applicable to Major Federal Actions Relating to Nuclear Activities Subject to Executive Order 12114 More Documents & Publications Environmental Effects Abroad of Major Federal Actions

422

Battery Test Manual For Plug-In Hybrid Electric Vehicles  

DOE Green Energy (OSTI)

This battery test procedure manual was prepared for the United States Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy (EERE), Vehicle Technologies Program. It is based on technical targets established for energy storage development projects aimed at meeting system level DOE goals for Plug-in Hybrid Electric Vehicles (PHEV). The specific procedures defined in this manual support the performance and life characterization of advanced battery devices under development for PHEV’s. However, it does share some methods described in the previously published battery test manual for power-assist hybrid electric vehicles. Due to the complexity of some of the procedures and supporting analysis, a revision including some modifications and clarifications of these procedures is expected. As in previous battery and capacitor test manuals, this version of the manual defines testing methods for full-size battery systems, along with provisions for scaling these tests for modules, cells or other subscale level devices.

Not Available

2008-03-01T23:59:59.000Z

423

Battery Test Manual For Plug-In Hybrid Electric Vehicles  

DOE Green Energy (OSTI)

This battery test procedure manual was prepared for the United States Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy (EERE), Vehicle Technologies Program. It is based on technical targets established for energy storage development projects aimed at meeting system level DOE goals for Plug-in Hybrid Electric Vehicles (PHEV). The specific procedures defined in this manual support the performance and life characterization of advanced battery devices under development for PHEV’s. However, it does share some methods described in the previously published battery test manual for power-assist hybrid electric vehicles. Due to the complexity of some of the procedures and supporting analysis, a revision including some modifications and clarifications of these procedures is expected. As in previous battery and capacitor test manuals, this version of the manual defines testing methods for full-size battery systems, along with provisions for scaling these tests for modules, cells or other subscale level devices.

Jeffrey R. Belt

2010-09-01T23:59:59.000Z

424

Battery Test Manual For Plug-In Hybrid Electric Vehicles  

SciTech Connect

This battery test procedure manual was prepared for the United States Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy (EERE), Vehicle Technologies Program. It is based on technical targets established for energy storage development projects aimed at meeting system level DOE goals for Plug-in Hybrid Electric Vehicles (PHEV). The specific procedures defined in this manual support the performance and life characterization of advanced battery devices under development for PHEV’s. However, it does share some methods described in the previously published battery test manual for power-assist hybrid electric vehicles. Due to the complexity of some of the procedures and supporting analysis, a revision including some modifications and clarifications of these procedures is expected. As in previous battery and capacitor test manuals, this version of the manual defines testing methods for full-size battery systems, along with provisions for scaling these tests for modules, cells or other subscale level devices.

Jeffrey R. Belt

2010-12-01T23:59:59.000Z

425

Test Automation Ant JUnit Test Automation  

E-Print Network (OSTI)

Test Automation Ant JUnit Test Automation Mohammad Mousavi Eindhoven University of Technology, The Netherlands Software Testing 2012 Mousavi: Test Automation #12;Test Automation Ant JUnit Outline Test Automation Ant JUnit Mousavi: Test Automation #12;Test Automation Ant JUnit Why? Challenges of Manual Testing

Mousavi, Mohammad

426

Advanced Vehicle Testing Activity: Energy Storage Testing  

NLE Websites -- All DOE Office Websites (Extended Search)

Energy Storage Testing to someone by E-mail Share Advanced Vehicle Testing Activity: Energy Storage Testing on Facebook Tweet about Advanced Vehicle Testing Activity: Energy...

427

Molten salt test loop  

DOE Green Energy (OSTI)

The objective of the Molten Salt Test Loop Project was to design, construct, and demonstrate operation of an outdoor high temperature molten salt test facility. This facility is operational, and can now be used to evaluate materials and components, and the design features and operating procedures required for molten salt heat transport systems. The initial application of the loop was to demonstrate the feasibility of using molten salt as the heat transport medium for a high temperature distributed collector system. A commercially available eutectic salt blend is used as the heat transfer fluid. This salt has a composition of 40% NaNO/sub 2/, 7% NaNO/sub 3/, and 53% KNO/sub 3/ and is marketed under the trade name Hitec. It has a freezing (solidifying) point of 142/sup 0/C (288/sup 0/F) and has been satisfactorily used at temperatures as high as 594/sup 0/C (1100/sup 0/F). General Atomic (GA) installed a row of Fixed Mirror Solar Concentrators (FMSC's) in the loop. The system was started up and a test program conducted. Startup went smoothly, with the exception of some burned-out trace heaters. Salt temperatures as high as 571/sup 0/C (1060/sup 0/F) were achieved.

Schuster, J.R.; Eggers, G.H.

1980-01-01T23:59:59.000Z

428

Chapter 50 Division for Air Quality: General Administrative Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

You are here You are here Home » Chapter 50 Division for Air Quality: General Administrative Procedures (Kentucky) Chapter 50 Division for Air Quality: General Administrative Procedures (Kentucky) < Back Eligibility Agricultural Commercial Construction Developer Fuel Distributor General Public/Consumer Industrial Installer/Contractor Investor-Owned Utility Municipal/Public Utility Rural Electric Cooperative Transportation Utility Program Info State Kentucky Program Type Environmental Regulations Provider Kentucky Department for Environmental Protection Chapter 50 of the Division of Air Quality section within Energy and Environment Cabinet Department For Environmental Protection outlines the general administrative procedures for maintaining air quality standards. These procedures are created in adherence to 42 USC 7410 which requires the

429

Policy and Procedures for the Review of Federal Actions Impacting...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

and Procedures for the Review of Federal Actions Impacting the Environment October 3, 1984 TABLE OF CONTENTS CHAPTER 1 - PURPOSE, POLICY, AND MANDATES 1. Purpose 2. Statutory...

430

Petroleum Pipeline Eminent Domain Permit Procedures (Georgia) | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Petroleum Pipeline Eminent Domain Permit Procedures (Georgia) Petroleum Pipeline Eminent Domain Permit Procedures (Georgia) Petroleum Pipeline Eminent Domain Permit Procedures (Georgia) < Back Eligibility Commercial Construction Developer Fuel Distributor General Public/Consumer Industrial Investor-Owned Utility Municipal/Public Utility Utility Program Info State Georgia Program Type Environmental Regulations Siting and Permitting Provider Georgia Department of Natural Resources The Petroleum Pipeline Eminent Domain Permit Procedures serve to protect Georgia's natural and environmental resources by requiring permits be issued by the Director of the Environmental Protection Division prior to any petroleum or petroleum product pipe company acquiring property or interests by eminent domain. Monitoring conditions will be issued with

431

Cost Transfers Involving Sponsored Projects Directives and Procedures  

E-Print Network (OSTI)

Cost Transfers Involving Sponsored Projects Directives and Procedures Responsible Office: Office....................................................................................................................2 1.3 Cost Transfer.................................................................................................................2 2. Project Management

Watson, Craig A.

432

Procedure for MOUs Between Fermilab & Foreign SUBJECT NUMBER ...  

SUBJECT: Procedure for MOUs Between Fermilab & Foreign Partners NUMBER: 4501 RESPONSIBILITY: Fermilab Chief Operating Officer REVISION: 01 APPROVED BY: Fermilab Chief ...

433

DOE NEPA Implementing Procedures: Final Rule (57 Fed Reg 15122...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Act," to incorporate revised provision of DOE's Guidelines for Implementing the Procedural Provisions of the National Environmental Policy Act (NEPA). 10CFR102104241992.pdf...

434

Model Recovery Procedure for Response to a Radiological Transportation Incident  

Energy.gov (U.S. Department of Energy (DOE))

This Transportation Emergency Preparedness Program (TEPP) Model Recovery Procedure contains the recommended elements for developing and conducting recovery planning at transportation incident scene...

435

Green Lease Policies and Procedures for Lease Acquisition | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Centers Field Sites Power Marketing Administration Other Agencies You are here Home Green Lease Policies and Procedures for Lease Acquisition Green Lease Policies and...

436

Attachment 1: Green Lease Policies and Procedures for Lease Acquisitio...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Sites Power Marketing Administration Other Agencies You are here Home Attachment 1: Green Lease Policies and Procedures for Lease Acquisition Attachment 1: Green Lease Policies...

437

Procedures for Interagency Consultation to Avoid or Mitigate...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Consultation to Avoid or Mitigate Adverse Effects on Rivers in the Nationwide Inventory Procedures for Interagency Consultation to Avoid or Mitigate Adverse Effects on...

438

Laboratory Procedures for using Infrared Thermography to Validate...  

NLE Websites -- All DOE Office Websites (Extended Search)

925 Laboratory Procedures for using Infrared Thermography to Validate Heat Transfer Models Daniel Trler, Brent T. Griffith, and Dariush K. Arasteh Lawrence Berkeley National...

439

Health and Safety Procedures Manual for hazardous waste sites  

SciTech Connect

The Oak Ridge National Laboratory Chemical Assessments Team (ORNL/CAT) has developed this Health and Safety Procedures Manual for the guidance, instruction, and protection of ORNL/CAT personnel expected to be involved in hazardous waste site assessments and remedial actions. This manual addresses general and site-specific concerns for protecting personnel, the general public, and the environment from any possible hazardous exposures. The components of this manual include: medical surveillance, guidance for determination and monitoring of hazards, personnel and training requirements, protective clothing and equipment requirements, procedures for controlling work functions, procedures for handling emergency response situations, decontamination procedures for personnel and equipment, associated legal requirements, and safe drilling practices.

Thate, J.E.

1992-09-01T23:59:59.000Z

440

FEDERAL REGISTER - 10 CFR Part 820 Procedurals Rules for DOE...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

and orders relating to nuclear safety. These procedural rules are intended to be an essential part of the framework through which DOE deals with its contractors,...

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Optimization Online - Hybrid LP/SDP Bounding Procedure  

E-Print Network (OSTI)

Oct 24, 2012... Bounding Procedure allows a noticeable reduction of computing time and a cut of almost one order of magnitude for the branching nodes.

442

Procedures for measuring the properties of heat-pipe wick materials  

DOE Green Energy (OSTI)

Accurate measurements of wick properties must be available to design high-performance beat pipes and to properly interpret results from heat pipe tests. In a program that is aimed at developing heat-pipe receivers for solar-Stirling electric systems, we have recently explored procedures to measure the effective pore radius and permeability of wick materials in their final ``as fabricated`` condition. Measurement techniques are compared in this paper and problems that are frequently encountered in measuring wick properties are discussed.

Adkins, D.R.; Dykhuizen, R.C.

1993-07-01T23:59:59.000Z

443

MITG test assembly design and fabrication  

DOE Green Energy (OSTI)

The design, analysis, and evaluation of the Modular Isotopic Thermoelectric Generator (MITG), described in an earlier paper, led to a program to build and test prototypical, modules of that generator. Each test module duplicates the thermoelectric converters, thermal insulation, housing and radiator fins of a typical generator slice, and simulates its isotope heat source module by means of an electrical heater encased in a prototypical graphite box. Once the approx. 20-watt MITG module has been developed, it can be assembled in appropriate number to form a generator design yielding the desired power output. The present paper describes the design and fabrication of the MITG test assembly, which confirmed the fabricability of the multicouples and interleaved multifoil insulation called for by the design. Test plans, procedures, instrumentation, results, and post-test analyses, as well as revised designs, fabrication procedures, and performance estimates, are described in subsequent papers in these proceedings.

Schock, A.

1983-01-01T23:59:59.000Z

444

Matrix Acidizing Core Flooding Apparatus: Equipment and Procedure Description  

E-Print Network (OSTI)

Core flooding is a commonly used experimental procedure in the petroleum industry. It involves pressurizing a reservoir rock and flowing fluid through it in the laboratory. The cylindrical rock, called a core, can be cut from the reservoir during a separate core drilling operation or a formation outcrop. A core flooding apparatus suitable for matrix acidizing was designed and assembled. Matrix acidizing is a stimulation technique in which hydrochloric acid (HCl) is injected down the wellbore below formation fracture pressure to dissolve carbonate (CaCO3) rock creating high permeability streaks called wormholes. The main components of the apparatus include a continuous flow syringe pump, three core holders, a hydraulic hand pump, two accumulators, a back pressure regulator, and two pressure transducers connected through a series of tubing and valves. Due to the corrosive nature of the acid, the apparatus features Hastelloy which is a corrosion resistant metal alloy. Another substantial feature of the apparatus is the ability to apply 3000psi back pressure. This is the pressure necessary to keep CO2, a product of the CaCO3 and HCl reaction, in solution at elevated temperatures. To perform experiments at temperature, the core holder is wrapped with heating tape and surrounded by insulation. Tubing is wrapped around a heating band with insulation to heat the fluid before it enters the core. A LabVIEW graphical programming code was written to control heaters as well as record temperature and pressure drop across the core. Other considerations for the design include minimizing footprint, operational ease by the user, vertical placement of the accumulators and core holders to minimize gravity effects, and air release valves. Core floods can be performed at varying injection rates, temperatures and pressures up to 5000psi and 250 degF. The apparatus can handle small core plugs, 1’’ diameter X 1’’ length, up to 4’’ X 20’’ cores. The equipment description includes the purpose, relevant features, and connections to the system for each component. Finally documented is the procedure to run a core flooding test to determine permeability and inject acid complete with an analysis of pressure response data.

Grabski, Elizabeth 1985-

2012-12-01T23:59:59.000Z

445

test | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

test test test test More Documents & Publications 2009 ECR FINAL REPORT 2010 Final ECR 2008 Report Environmental Conflict Resolution...

446

Procedure for Measuring and Reporting Commercial Building Energy Performance  

SciTech Connect

This procedure is intended to provide a standard method for measuring and characterizing the energy performance of commercial buildings. The procedure determines the energy consumption, electrical energy demand, and on-site energy production in existing commercial buildings of all types. The performance metrics determined here may be compared against benchmarks to evaluate performance and verify that performance targets have been achieved.

Barley, D.; Deru, M.; Pless, S.; Torcellini, P.

2005-10-01T23:59:59.000Z

447

Simple procedure for schematic design of passive solar buildings  

SciTech Connect

A simple procedure for use during the schematic phase of passive solar building design is presented in this article. The procedure is quantitative and accurate enough to insure that designs based on the provided starting point values of the primary building parameters will be cost effective.

Wray, W.O.; Kosiewicz, C.E.

1984-01-01T23:59:59.000Z

448

Aspect-oriented procedural content engineering for game design  

Science Conference Proceedings (OSTI)

Generally progressive procedural content in the context of 3D scene rendering is expressed as recursive functions where a finer level of detail gets computed on demand. Typical examples of content procedurally generated are fractal images ... Keywords: AO techniques, aspect-oriented programming, data engineering, meta-data

Walter Cazzola; Diego Colombo; Duncan Harrison

2009-03-01T23:59:59.000Z

449

Procedure for matching synfuel users with potential suppliers. Final report  

DOE Green Energy (OSTI)

A procedure has been developed for matching prospective users and producers of synthetic fuels. The matching procedure, which involves a hierarchical screening process, is designed to assist OFC in: locating a supplier for a firm that wishes to obtain synthetic fuel exemption (Fuel Use Act); determining whether the fuel supplier proposed by a petitioner is technically and economically capable of meeting the petitioner's needs; and assisting the Synthetic Fuels Corporation in evaluating potential markets for synthetic fuels. Application of the screening procedure resulted in the identification of one or more candidates for supplying synthetic fuel to each of the prospective users. In this report the development of the screening procedure is described. Chapter 1 contains a detailed description of the seven screens; Chapter 2 describes the development of the hierarchical procedure for applying the screens to each synthetic fuels project; Chapter 3 describes the modification of the screening procedure for low and medium Btu gas; Chapter 4 describes the application of the procedure. Appendix A is a list of references used in developing the procedure; Appendix B is a detailed listing of proposed and ongoing synthetic fuel projects.

None

1981-09-26T23:59:59.000Z

450

Index of /research/alcator/facility/Procedures/DIAGNOSTICS  

NLE Websites -- All DOE Office Websites (Extended Search)

DIAGNOSTICS DIAGNOSTICS [ICO] Name Last modified Size Description [DIR] Parent Directory - [ ] DNB Emergency Off Procedures42208.pdf 22-Apr-2008 15:58 73K [ ] DNB Emergency Off Procedures reva.pdf 04-Dec-2008 07:02 74K [ ] DNB Interim Safety Procedures050608.pdf 06-May-2008 14:11 1.2M [ ] FIR Laser Pumpout Procedure Rev 1.00.pdf 23-Apr-2008 16:05 22K [ ] FIR Laser Startup Procedure Rev 1.00.pdf 23-Apr-2008 16:05 29K [ ] FIR Laser Venting Procedure Rev 1.00.pdf 23-Apr-2008 16:05 22K [ ] Safety procedure for deuterium DNB operation.pdf 09-Jul-2003 13:01 8.2K [TXT] Safety procedure for deuterium DNB operation.txt 09-Jul-2003 13:01 4.5K [ ] TCI Window Cleaning.pdf 07-May-2003 14:32 62K [TXT] TCI Window Cleaning.txt 06-May-2003 14:38 3.2K

451

SPR Crude Oil Acquisition Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

SPR Crude Oil Acquisition Procedures SPR Crude Oil Acquisition Procedures SPR Crude Oil Acquisition Procedures Section 301(e)(2) of the Energy Policy Act of 2005 (Public Law 109-58) directs the Secretary of Energy to develop procedures to acquire petroleum, subject to certain conditions, in quantities to fill the Strategic Petroleum Reserve (SPR) to the authorized one billion barrel capacity. On April 24, 2006, a Notice of Proposed Rulemaking (NOPR) for acquisition of crude oil for the SPR was published in the Federal Register. The procedures include provisions for acquisition through several means, including direct purchase, by transfer of royalty oil from the Department of the Interior, and by receipt of premium barrels resulting from deferral of scheduled deliveries of petroleum for the Reserve.

452

DOE NEPA Implementing Procedures: Final Rule (61 Fed Reg 64603) |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

NEPA Implementing Procedures: Final Rule (61 Fed Reg 64603) NEPA Implementing Procedures: Final Rule (61 Fed Reg 64603) DOE NEPA Implementing Procedures: Final Rule (61 Fed Reg 64603) DOE amended its regulations governing compliance with the National Environmental Policy Act (NEPA). These amendments incorporate changes primarily related to DOE's power marketing activities, based on DOE's experience in applying the current NEPA regulations. The revised regulations are intended to improve DOE's efficiency in implementing NEPA requirements by reducing costs and preparation time, while maintaining quality, consistent with the DOE Secretarial Policy Statement on NEPA issued in June 1994. 61 Fed Reg 64603: DOE NEPA Implementing Procedures-Final Rule More Documents & Publications DOE NEPA Implementing Procedures: Final Rule (61 Fed Reg 36222)

453

Established and Revised Federal Agency NEPA Procedures, 2000 - 2011  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

and Revised Federal Agency NEPA Procedures, 2000 - 2011 and Revised Federal Agency NEPA Procedures, 2000 - 2011 ` Established and Revised Federal Agency NEPA Procedures Last Updated on January 11, 2013 Department/Agency Action Title/Citation Federal Register Notice(s) 2000 Department of Health and Human Services Revised NEPA Procedures Revised General Administration Manual, HHS Part 30, Environmental Protection Published for comment on January 11, 1999 (64 Federal Register [FR] 1655). Published as final procedures on February 25, 2000 (65 FR 10229). Bureau of Reclamation Department of the Interior Notice of Availability of a Draft Agency Handbook on the National Environmental Policy Act Department Manual (DM) Part 516, Chapter 6: Managing the NEPA Process (Appendix 7) Published on April 20, 2000 (65 FR 21210) with

454

Department of Energy Technical Standards Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Department Department of Energy Technical Standards Procedures Department of Energy Technical Standards Procedures The following procedures should be used to write, revise, or maintain a DOE technical standard. They are also used to convert a DOE technical standard to a non-government standard or to form a topical committee. TSPP September 2013 September 16, 2013 DOE-TSPP-1-2013, Program Overview and Responsibilities This procedure describes the responsibilities of persons who are charged with implementing the Department of Energy (DOE) Technical Standards Program (TSP). September 16, 2013 DOE-TSPP-2-2013, Initiating DOE Technical Standards This procedure provides guidance on how to establish and justify the need for a Department of Energy (DOE) Technical Standard and register a DOE

455

Current status of bioassay procedures to detect and quantify previous exposures to radioactive materials. Bioassay Procedures Working Group  

Science Conference Proceedings (OSTI)

This report was prepared by a working group established by the Oak Ridge Associated Universities (ORAU) for the purpose of assessing the current capabilities of bioassay methods that can be used to determine the occurrence and magnitude of a previous internal deposition of one or more radionuclides. The first five sections discuss general features of the use of in-vitro bioassay samples to achieve this purpose. The remainder of the report is focused on the possible use of urine bioassay procedures to detect and quantify internal depositions of radionuclides that may have occurred in United States occupation troops in Hiroshima or Nagasaki, Japan, prior to 1 July 1946, or to personnel who participated in atmospheric nuclear weapons tests conducted between 1945 and 1962. Theoretical calculations were made to estimate the quantities of various radionuclides produced in a 20-kiloton (kt) nuclear detonation that might still be present in measurable quantities in people today if they were exposed 25 to 40 y ago. Two radionuclides that emerged as good choices for this type of bioassay analysis were 90Sr, which emits beta particles, and 239,240Pu, which emits alpha particles. The current status and future prospects of chemical procedures for analyzing in-vitro urine bioassay samples for these two radionuclides were examined to determine the minimum amounts that could be detected with current methods and how much one might expect the sensitivity of detection to improve in the near future. Most routine 239,240Pu bioassay analyses involve detection by alpha spectrometry. The current minimum detectable amount (MDA) is about 0.74 mBq L-1 (20 fCi L-1), but this could be lowered to 74 muBq L-1 (2 fCi L-1). An MDA of 0.74 mBq L-1 (20 fCi L-1) is adequate for routine bioassay analyses but is too high to detect most uptakes of 239,240Pu that may have occurred 25 to 40 y ago.

Boecker, B.; Hall, R.; Inn, K.; Lawrence, J.; Ziemer, P.; Eisele, G.; Wachholz, B.; Burr, W. Jr. (Lovelace Inhalation Toxicology Research Institute, Albuquerque, NM (USA))

1991-01-01T23:59:59.000Z

456

An Experimental Test Bed for Small Unmanned Helicopters  

Science Conference Proceedings (OSTI)

This paper introduces a custom experimental test bed for the evaluation of autonomous flight controllers for unmanned helicopters. The development of controllers for unmanned helicopters is a difficult procedure which involves testing through simulation ... Keywords: Aerial robotics, Experimental test bed, Flight control, Fuzzy control, Unmanned helicopters

Nikos I. Vitzilaios; Nikos C. Tsourveloudis

2009-05-01T23:59:59.000Z

457

ITS strategic test plan : revision 1.0.  

SciTech Connect

This test plan describes the testing strategy for the ITS (Integrated-TIGER-Series) suite of codes. The processes and procedures for performing both verification and validation tests are described. ITS Version 5.0 was developed under the NNSA's ASC program and supports Sandia's stockpile stewardship mission.

Franke, Brian Claude; Lorence, Leonard Joseph, Jr.; Crawford, Martin James (K-Tech Corporation, Albuquerque, NM); Cordova, Lisa A.; Kensek, Ronald Patrick; Laub, Thomas William

2004-07-01T23:59:59.000Z

458

Evaluation criteria and test methods for electrochromic windows  

SciTech Connect

Report summarizes the test methods used for evaluating electrochromic (EC) windows, and summarizes what is known about degradation of their performance, and recommends methods and procedures for advancing EC windows for buildings applications. 77 refs., 13 figs., 6 tabs.

Czanderna, A.W. (Solar Energy Research Inst., Golden, CO (USA)); Lampert, C.M. (Lawrence Berkeley Lab., CA (USA))

1990-07-01T23:59:59.000Z

459

Energy test method development for electric heat pump water heaters  

SciTech Connect

Modifications are proposed for the current US Department of Energy test procedures for water heaters in order to make them applicable to electric heat pump water heaters. The modifications are in the areas of definitions and technical procedures. The latter include the test conditions, test procedures and measurements, and calculations. Reasons for making these modifications and laboratory test data are provided to support the modifications in the technical procedures. The main modifications include: (1) lowering the water supply temperature from 70/sup 0/F to 55/sup 0/F, (2) lowering the tank thermostat setting from 160/sup 0/F to 145/sup 0/F to maintain the same 90/sup 0/F temperature rise, (3) measuring the power input instead of using the nameplate rating as in the case for an electric water heater, and (4) measuring the recovery efficiency instead of calculating it by using the standby losses in the case for an electric water heater.

Wan, C.A.

1980-01-01T23:59:59.000Z

460

Nondestructive Tests and Their Applicability to P/M Processing  

Science Conference Proceedings (OSTI)

...Radiographic techniques Acoustic methods Thermal inspection Electrical resistivity inspection Visual inspection and pressure testing The techniques covered in this article are summarized in Table 1. Additional information on these procedures

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Evaluation tests for photovoltaic concentrator receiver sections and modules  

DOE Green Energy (OSTI)

Sandia has developed a third-generation set of specifications for performance and reliability testing of photovoltaic concentrator modules. Several new requirements have been defined. The primary purpose of the tests is to screen new concentrator designs and new production runs for susceptibility to known failure mechanisms. Ultraviolet radiation testing of materials precedes receiver section and module performance and environmental tests. The specifications include the purpose, procedure, and requirements for each test. Recommendations for future improvements are presented.

Woodworth, J.R.; Whipple, M.L.

1992-06-01T23:59:59.000Z

462

Calmac Ice Storage Test report  

DOE Green Energy (OSTI)

The Ice Storage Test Facility (ISTF) is designed to test commercial ice storage systems. Calmac provided a storage tank equipped with coils designed for use with a secondary fluid system. The Calmac ice storage system was tested over a wide range of operating conditions. Measured system performance during charging was similar to that reported by the manufacturer. Both the measured average and minimum brine temperatures were in close agreement with Calmac's literature values, and the ability to fully charge the tank was relatively unaffected by charging rate and brine flow rate. During discharge cycles, the storage tank outlet temperature was strongly affected by the discharge rate. The discharge capacity was dependent upon both the selected discharge rate and maximum allowable tank outlet temperature. Based on these tests, storage tank selection must depend most strongly on the discharge conditions required to serve the load. This report describes Calmac system performance fully under both charging and discharging conditions. Companion reports describe ISTF test procedures and ice-making efficiency test results that are common to many of the units tested. 11 refs., 31 figs., 9 tabs.

Stovall, T.K.

1991-08-01T23:59:59.000Z

463

Test report for cesium powder and pellets inner container decontamination method determination test  

SciTech Connect

This report documents the decontamination method determination testing that was performed on three cesium powder and pellets inner container test specimens The test specimens were provided by B and W Hanford Company (BVMC). The tests were conducted by the Numatec Hanford Company (NHC), in the 305 Building. Photographic evidence was also provided by NHC. The Test Plan and Test Report were provided by Waste Management Federal Services, Inc., Northwest Operations. Witnesses to testing included a test engineer, a BC project engineer, and a BC Quality Assurance (QA) representative. The Test Plan was modified with the mutual decision of the test engineer, the BWHC project engineer, and the BVMC QA representative. The results of this decision were written in red (permanent type) ink on the official copy of the test procedure, Due to the extent of the changes, a summary of the test results are provided in Section 3.0 of this Test Report. In addition, a copy of the official copy field documentation obtained during testing is included in Appendix A. The original Test Plan (HNF-2945) will be revised to indicate that extensive changes were required in the field during testing, however, the test documentation will stand as is (i.e., it will not be retyped, text shaded, etc.) due to the inclusion of the test parameters and results into this Test Report.

Kelly, D.L.

1998-08-17T23:59:59.000Z

464

Chapter 30 Waste Management: General Administrative Procedures (Kentucky) |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Chapter 30 Waste Management: General Administrative Procedures Chapter 30 Waste Management: General Administrative Procedures (Kentucky) Chapter 30 Waste Management: General Administrative Procedures (Kentucky) < Back Eligibility Agricultural Commercial Construction Developer Fed. Government Fuel Distributor Industrial Installer/Contractor Institutional Investor-Owned Utility Local Government Retail Supplier Rural Electric Cooperative State/Provincial Govt Systems Integrator Transportation Tribal Government Utility Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Solar Buying & Making Electricity Wind Program Info State Kentucky Program Type Environmental Regulations Provider Department for Environmental Protection The waste management administrative regulations apply to the disposal of solid waste and the management of all liquid, semisolid, solid, or gaseous

465

Full Scale Tornado Missile Impact Tests  

Science Conference Proceedings (OSTI)

At the time of this interim report, approximately half the tests scheduled in the EPRI/Sandia Tornado-Missile Program had been completed. This report was issued to disseminate the results of the initial tests as quickly as possible, in order to satisfy the needs of utilities and architect-engineers engaged in plant-licensing procedures. The findings are presented with a minimum of interpretation.

1976-04-01T23:59:59.000Z

466

Evaluation and Test of Improved Fire Resistant Fluid Lubricants for Water Reactor Coolant Pump Motors, Volume 1: Fluid Evaluation, Bearing Model Tests, Motor Tests, and Fire Tests  

Science Conference Proceedings (OSTI)

Commercially available fire-resistant fluid lubricants were evaluated to determine their suitability for use in primary-system pump motors in nuclear reactors. Volume 1 describes the procedures and results of tests of lubrication properties; fire and radiation resistance; and thermal, oxidative, and hydrolytic stability.

1980-07-01T23:59:59.000Z

467

Building Technologies Office: Standardized Templates for Reporting Test  

NLE Websites -- All DOE Office Websites (Extended Search)

Standardized Templates Standardized Templates for Reporting Test Results to someone by E-mail Share Building Technologies Office: Standardized Templates for Reporting Test Results on Facebook Tweet about Building Technologies Office: Standardized Templates for Reporting Test Results on Twitter Bookmark Building Technologies Office: Standardized Templates for Reporting Test Results on Google Bookmark Building Technologies Office: Standardized Templates for Reporting Test Results on Delicious Rank Building Technologies Office: Standardized Templates for Reporting Test Results on Digg Find More places to share Building Technologies Office: Standardized Templates for Reporting Test Results on AddThis.com... About Standards & Test Procedures Implementation, Certification & Enforcement

468

Monitored Geologic Repository Test Evaluation Plan  

SciTech Connect

The Monitored Geologic Repository test & evaluation program will specify tests, demonstrations, examinations, and analyses, and describe procedures to conduct and document testing necessary to verify meeting Monitored Geologic Repository requirements for a safe and effective geologic repository for radioactive waste. This test program will provide assurance that the repository is performing as designed, and that the barriers perform as expected; it will also develop supporting documentation to support the licensing process and to demonstrate compliance with codes, standards, and regulations. This comprehensive program addresses all aspects of verification from the development of test requirements to the performance of tests and reporting of the test results. The ''Monitored Geologic Repository Test & Evaluation Plan'' provides a detailed description of the test program approach necessary to achieve the above test program objectives. This test plan incorporates a set of test phases focused on ensuring repository safety and operational readiness and implements a project-wide integrated product management team approach to facilitate test program planning, analysis, and implementation. The following sections provide a description of the individual test phases, the methodology for test program planning and analyses, and the management approach for implementing these activities.

M.B. Skorska

2002-01-02T23:59:59.000Z

469

Aflatoxin Test Kit Laboratory Proficiency Testing  

Science Conference Proceedings (OSTI)

Lab proficiency testing for Aflatoxin test kit to determine Total Aflatoxins.Samples include Peanut Paste, Corn Meal, Milk. Aflatoxin Test Kit Laboratory Proficiency Testing Laboratory Proficiency Program (LPP) aocs applicants certified chemist chemists

470

Building America System Performance Test Practices: Part 1 -- Photovoltaic Systems  

DOE Green Energy (OSTI)

The report outlines the short-term field testing used by Building America staff and includes a report on the results of an example test of a PV system with battery storage on a home in Tucson, Arizona. This report is not intended as a general recommended test procedure for wide distribution. It is intended to document current practices in Building America to inform program stakeholders and stimulate further discussion. Building America staff intend to apply this procedure until relevant standards for testing PV modules are completed.

Barker, G.; Norton, P.

2003-05-01T23:59:59.000Z

471

Net Metering and Interconnection Procedures-- Incorporating Best Practices  

SciTech Connect

State utility commissions and utilities themselves are actively developing and revising their procedures for the interconnection and net metering of distributed generation. However, the procedures most often used by regulators and utilities as models have not been updated in the past three years, in which time most of the distributed solar facilities in the United States have been installed. In that period, the Interstate Renewable Energy Council (IREC) has been a participant in more than thirty state utility commission rulemakings regarding interconnection and net metering of distributed generation. With the knowledge gained from this experience, IREC has updated its model procedures to incorporate current best practices. This paper presents the most significant changes made to IREC���¢��������s model interconnection and net metering procedures.

Jason Keyes, Kevin Fox, Joseph Wiedman, Staff at North Carolina Solar Center

2009-04-01T23:59:59.000Z

472

NASA Procedural Requirements NPR 8020.12D  

E-Print Network (OSTI)

on Space Research (COSPAR) Planetary Protection Policy, as amended. e. NASA HDBK 6022, NASA Standard. Assay Methods (1) Utilization of NASA HDBK 6022 , NASA Standard Procedures for the Microbiological

Rhoads, James

473

Doffing procedures for firefighters' contaminated turnout gear: Documentation for videotape  

SciTech Connect

This report summarizes the doffing procedures and provides a copy of the videotape script, which includes a fire brigade returning to a mock decontamination area after dealing with a simulated fire. The report also provides background information explaining why the videotape was made, how the project was accomplished, and what the procedures are intended to accomplish. Overall, the video gives step-by-step instructions for the removal of contaminated turnout gear and indicates how firefighters and radiation protection personnel can work together cooperatively. These new doffing procedures were developed with the advice and participation of actual nuclear power plant firefighting personnel at the Seabrook Station of New Hampshire Yankee utility and may be adapted to enhance any existing in-plant procedures. The video includes comments from members of the fire brigade, an equipment review, and a discussion of the doffing area arrangement.

Not Available

1992-07-01T23:59:59.000Z

474

Current Human Reliability Analysis Methods Applied to Computerized Procedures  

SciTech Connect

Computerized procedures (CPs) are an emerging technology within nuclear power plant control rooms. While CPs have been implemented internationally in advanced control rooms, to date no US nuclear power plant has implemented CPs in its main control room (Fink et al., 2009). Yet, CPs are a reality of new plant builds and are an area of considerable interest to existing plants, which see advantages in terms of enhanced ease of use and easier records management by omitting the need for updating hardcopy procedures. The overall intent of this paper is to provide a characterization of human reliability analysis (HRA) issues for computerized procedures. It is beyond the scope of this document to propose a new HRA approach or to recommend specific methods or refinements to those methods. Rather, this paper serves as a review of current HRA as it may be used for the analysis and review of computerized procedures.

Ronald L. Boring

2012-06-01T23:59:59.000Z

475

Development of an Automated Classification Procedure for Rainfall Systems  

Science Conference Proceedings (OSTI)

An automated procedure for classifying rainfall systems (meso-? scale and larger) was developed using an operational analysis of hourly precipitation estimates from radar and rain gauge data. The development process followed two main phases: a ...

Michael E. Baldwin; John S. Kain; S. Lakshmivarahan

2005-04-01T23:59:59.000Z

476

Doffing Procedures for Firefighters' Contaminated Turnout Gear: Documentation for Videotape  

Science Conference Proceedings (OSTI)

Firefighting in an area contaminated by radioactive materials can result in contaminated clothing that requires careful handling. This report documents a videotape that provides simple how-to procedures for doffing contaminated or potentially contaminated firefighter turnout gear.

1992-07-01T23:59:59.000Z

477

Analysis and Experiments with a Slow-Start Procedure  

Science Conference Proceedings (OSTI)

Slow-start procedures were developed decades ago in order to provide a smoother evolution in numerical simulations performed with three-time-level integration schemes. The advantages of a slow start versus a conventional forward start should ...

Harold Ritchie; Anne-Marie Leduc

1994-04-01T23:59:59.000Z

478

On the Translation of Procedures to Finite Machines  

Science Conference Proceedings (OSTI)

We prove the correctness of the translation of a prototypic While-language with nested, parameterless procedures to an abstract assembler language with finite stacks. A variant of the well-known wp and wlp predicate transformers, the weakest relative ...

Markus Müller-Olm; Andreas Wolf

2000-04-01T23:59:59.000Z

479

Princeton Plasma Physics Laboratory D-SITE Procedure  

E-Print Network (OSTI)

) Lift Procedure (ENG-021) Confined Space Permit DCA/DCN (OP-AD-104) Pre-job brief (OP-AD-79) ATI requirements and provides checklists for documenting training Training Rep. _______________________________ RLM

Princeton Plasma Physics Laboratory

480

A voice enabled procedure browser for the International Space Station  

Science Conference Proceedings (OSTI)

Clarissa, an experimental voice enabled procedure browser that has recently been deployed on the International Space Station (ISS), is to the best of our knowledge the first spoken dialog system in space. This paper gives background on the system and ...

Manny Rayner; Beth Ann Hockey; Nikos Chatzichrisafis; Kim Farrell; Jean-Michel Renders

2005-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "test procedures seer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Procedural design considerations associated with tubing-conveyed underbalanced perforating  

Science Conference Proceedings (OSTI)

Thirty-two tubing conveyed underbalanced perforating jobs conducted in the Gulf of Mexico between May, 1980, and May, 1982, have been carefully reviewed in order to draw correlations between procedural variations and trouble prone jobs. General procedural guidelines designed to avoid past problems were formulated and are presented. The procedures are designed for the generalized case where the perforating guns will be pulled out of the well in order to gravel pack and not for those run as part of a permanent completion. Careful application of these procedural guidelines has resulted in reducing rig time requirements by an average of 35% on 33 additional tubing conveyed underbalanced perforating jobs conducted subsequent to the establishment of the guidelines contained in this paper.

Young, W.S.; Zaleski, T.E.

1985-03-01T23:59:59.000Z

482

Modeling and managing separation for noise abatement arrival procedures  

E-Print Network (OSTI)

Aircraft noise is a significant concern to communities near airports, and therefore a constraint to the growth of aviation. Advanced noise abatement approach and arrival procedures have been shown in previous studies and ...

Ren, Liling

2007-01-01T23:59:59.000Z

483

Identifying Non-Federal Cooperating Agencies in Implementing the Procedural  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Identifying Non-Federal Cooperating Agencies in Implementing the Identifying Non-Federal Cooperating Agencies in Implementing the Procedural Requirements of NEPA Identifying Non-Federal Cooperating Agencies in Implementing the Procedural Requirements of NEPA The purpose of this Council on Environmental Quality Memorandum is to ensure that all federal and non-federal cooperating agencies are identified on the cover sheet of each Environmental Impact Statement (EIS) prepared by your agency. G-CEQ-IdentnonfedCooperatingAgencies.pdf More Documents & Publications Designation of Non-Federal Agencies as Cooperating Agencies Cooperating Agencies in Implementing the Procedural Requirements of the National Environmental Policy Act Reporting Cooperating Agencies in Implementing the Procedural Requirements of the National Environmental Policy Act

484

Environmental Assessment for the LGF Spill Test Facility at Frenchman Flat, Nevada Test Site  

Science Conference Proceedings (OSTI)

The LGF Spill Test Facility at Frenchman Flat, Nevada Test Site, is being constructed by the United States Department of Energy (DOE). In this Environmental Assessment, environmental consequences of spilling hazardous materials in the Frenchman Flat basin are evaluated and mitigations and recommendations are stated in order to protect natural resources and reduce land-use impacts. Guidelines and restrictions concerning spill-test procedures will be determined by the LGF Test Facility Operations Manager and DOE based on toxicity documentation for the test material, provided by the user, and mitigations imposed by the Environmental Assessment. In addition to Spill Test Facility operational procedures, certain assumptions have been made in preparation of this document: no materials will be considered for testing that have cumulative, long-term persistence in the environment; spill tests will consist of releases of 15 min or less; and sufficient time will be allowed between tests for recovery of natural resources. Geographic limits to downwind concentrations of spill materials were primarily determined from meteorological data, human occupational exposure standards to hazardous materials and previous spill tests. These limits were established using maximum spill scenarios and environmental impacts are discussed as worst case scenarios; however, spill-test series will begin with smaller spills, gradually increasing in size after the impacts of the initial tests have been evaluated.

Patton, S.E.; Novo, M.G.; Shinn, J.H.

1986-04-01T23:59:59.000Z

485

Repair and Replacement Applications Center Joint Welding Procedure Qualification Program  

Science Conference Proceedings (OSTI)

At the request of the EPRI Repair and Replacement Applications Center subscribers, a Joint Welding Procedure Qualification Program was developed to provide a medium whereby multiple utilities can share in the qualification of specific welding procedures. The program was developed in such a manner that it will supplement existing utility welding qualification programs. Specifically the program incorporates the more stringent attributes of each utility's internal welding program while meeting the individua...

1997-11-12T23:59:59.000Z

486

Illustration of a New Test for Detecting a Shift in Mean in Precipitation Series  

Science Conference Proceedings (OSTI)

Maronna and Yohai (1978) have introduced a new test for detecting a shift in mean in an independent time series, based on a second correlated series. Unlike other procedures commonly applied to precipitation series, this test is statistically ...

Kenneth W. Potter

1981-09-01T23:59:59.000Z

487

Controlling the Proportion of Falsely Rejected Hypotheses when Conducting Multiple Tests with Climatological Data  

Science Conference Proceedings (OSTI)

The analysis of climatological data often involves statistical significance testing at many locations. While the field significance approach determines if a field as a whole is significant, a multiple testing procedure determines which particular ...

Valérie Ventura; Christopher J. Paciorek; James S. Risbey

2004-11-01T23:59:59.000Z

488

Mode-Stirred Method Implementation for HIRF Susceptibility Testing and Results Comparison with Anechoic Method  

Science Conference Proceedings (OSTI)

This paper describes the implementation of mode-stirred method for susceptibility testing according to the current DO-160D standard. Test results on an Engine Data Processor using the implemented procedure and the comparisons with the standard anechoic ...

Nguyen Truong X.; Ely Jay J.; Koppen Sandra V.

2001-07-01T23:59:59.000Z

489

Survey of solar thermal test facilities  

DOE Green Energy (OSTI)

The facilities that are presently available for testing solar thermal energy collection and conversion systems are briefly described. Facilities that are known to meet ASHRAE standard 93-77 for testing flat-plate collectors are listed. The DOE programs and test needs for distributed concentrating collectors are identified. Existing and planned facilities that meet these needs are described and continued support for most of them is recommended. The needs and facilities that are suitable for testing components of central receiver systems, several of which are located overseas, are identified. The central contact point for obtaining additional details and test procedures for these facilities is the Solar Thermal Test Facilities Users' Association in Albuquerque, N.M. The appendices contain data sheets and tables which give additional details on the technical capabilities of each facility. Also included is the 1975 Aerospace Corporation report on test facilities that is frequently referenced in the present work.

Masterson, K.

1979-08-01T23:59:59.000Z

490

Test facility for PLT TF coils  

SciTech Connect

Past experience with the model C stellerator and other toroidal field devices indicates that mechanical and electrical tests of a toroidal field coil prior to maximum field operation of the device is prudent and desirable. This paper describes a test program for the PLT-TF coils. The test stand consists of one test coil, two background coils and a steel supporting structure. The three coil configuration produces a 67.5 kG field at the inner conductor (38 kG at the bore center) and simulates a 1/R field distribution in the bore of the test coil. The resolution of the field force system and resultant stresses within the test structure are discussed. A test procedure is described which maximizes the information obtained from a 100,000 pulse program. (auth)

Hearney, J.; File, J.; Dreskin, S.

1975-01-01T23:59:59.000Z

491

Test Purpose Generation for Timed Protocol Testing  

Science Conference Proceedings (OSTI)

Test purposes are requirements, usually constructed by hand, which aim at testing critical properties on implementations. These ones are then used by testing methods to generate test cases. Writing them manually is a heavy task, this is why we propose ... Keywords: Timed protocols, conformance testing, test purpose, testability

Sébastien Salva; Antoine Rollet

2009-07-01T23:59:59.000Z

492

REAL-TIME TRACER MONITORING OF RESERVOIR STIMULATION PROCEDURES VIA ELECTRONIC WIRELINE AND TELEMETRY DATA TRANSMISSION  

SciTech Connect

Ongoing Phase 2-3 work comprises the final development and field-testing of two complementary real-time reservoir technologies; a stimulation process and a tracer fracturing diagnostic system. Initial DE-FC26-99FT40129 project work included research, development, and testing of the patented gamma tracer fracturing diagnostic system. This process was field-proven to be technically useful in providing tracer measurement of fracture height while fracturing; however, technical licensing restrictions blocked Realtimezone from fully field-testing this real-time gamma diagnostic system, as originally planned. Said restrictions were encountered during Phase 2 field test work as result of licensing limitations and potential conflicts between service companies participating in project work, as related to their gamma tracer logging tool technology. Phase 3 work principally demonstrated field-testing of Realtimezone (RTZ) and NETL's Downhole-mixed Reservoir Stimulation process. Early on, the simplicity of and success of downhole-mixing was evident from well tests, which were made commercially productive. A downhole-mixed acid stimulation process was tested successfully and is currently commercially used in Canada. The fourth well test was aborted due to well bore conditions, and an alternate test project is scheduled April, 2004. Realtimezone continues to effectuate ongoing patent protection in the United States and foreign markets. In 2002, Realtimezone and the NETL licensed their United States patent to Halliburton Energy Services (HES). Additional licensing arrangements with other industry companies are anticipated in 2004-2005. Ongoing Phase 2 and Phase 3 field-testing continues to confirm applications of both real-time technologies. Technical data transfer to industry is ongoing via Internet tech-transfer and various industry presentations and publications including Society of Petroleum Engineers. These real-time enhanced stimulation procedures should significantly increase future petroleum well recoveries in the United States, onshore and offshore, and in vertical and horizontal wells.

George Scott III

2003-08-01T23:59:59.000Z

493

Evaluation of Revised Computer-Based Procedure System Prototype  

SciTech Connect

The nuclear power industry is very procedure driven, i.e. almost all activities that take place at a nuclear power plant are conducted by following procedures. The paper-based procedures (PBPs) currently used by the industry do a good job at keeping the industry safe. However, these procedures are most often paired with methods and tools put in place to anticipate, prevent, and catch errors related to hands-on work. These tools are commonly called human performance tools. The drawback with the current implementation of these tools is that the task of performing one procedure becomes time and labor intensive. For example, concurrent and independent verification of procedure steps are required at times, which essentially means that at least two people have to be actively involved in the task. Even though the current use of PBPs and human performance tools are keeping the industry safe, there is room for improvement. The industry could potentially increase their efficiency and safety by replacing their existing PBPs with CBPs. If implemented correctly, the CBP system could reduce the time and focus spent on using the human performance tools. Some of the tools can be completely incorporated in the CBP system in a manner that the performer does not think about the fact that these tools are being used. Examples of these tools are procedure use and adherence, placekeeping, and peer checks. Other tools can be partly integrated in a fashion that reduce the time and labor they require, such as concurrent and independent verification. The incorporation of advanced technology, such as CBP systems, may help to manage the effects of aging systems, structures, and components. The introduction of advanced technology may also make the existing LWR fleet more attractive to the future workforce, which will be of importance when the future workforce will chose between existing fleet and the newly built nuclear power plants.

Katya Le Blanc; Johanna Oxstrand; Cheradan Fikstad

2013-01-01T23:59:59.000Z

494

Fermentation guide for potatoes. A step-by-step procedure for small-scale ethanol fuel production  

Science Conference Proceedings (OSTI)

This guide describes the steps involved in the successful batch starch conversion and fermentation of potatoes for the production of fuel grade ethanol. The first part of this manual provides an overview of ethanol production from feedstock to fermentation. The second part of the manual is a recipe section that gives step-by-step procedures necessary for successful fermentation. Chapter titles are: major steps in ethanol production; equipment and chemicals; water testing and treatment; feedstock cleaning and crushing; precooking; hydration and dextrinization; cooking; choosing the best enzymes; fermentation; core and cleaning, step-by-step procedure; refinements; and supplies. (DMC)

Not Available

1981-09-01T23:59:59.000Z

495

Test definitions for the evaluation of infrasound sensors.  

SciTech Connect

Most test methodologies referenced in this Test Definition and Test Procedures were designed by Sandia specifically for geophysical instrumentation evaluation. When appropriate, test instrumentation calibration is traceable to the National Institute for Standards Technology (NIST). The objectives are to evaluate the overall technical performance of the infrasound sensor. The results of these evaluations can be compared to the manufacturer's specifications and any relevant application requirements or specifications.

Kromer, Richard Paul (R.P. Kromer Consulting, Albuquerque, NM); Hart, Darren M.; Harris, James Mark

2007-07-01T23:59:59.000Z

496

Test Acquisition Guide | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Test Acquisition Guide Test Acquisition Guide Test Acquisition Guide Regulatory requirements for the acquisition process are set forth in the Federal Acquisition Regulation (FAR) and are supplemented in the Department of Energy Acquisition Regulation (DEAR). FAR 1.301 provides for the issuance of additional internal agency guidance, including designations and delegations of authority, assignments of responsibilities, work-flow procedures, and internal reporting requirements. The DOE Acquisition Guide serves this purpose by identifying relevant internal standard operating procedures to be followed by both procurement and program personnel who are involved in various aspects of the acquisition process. The Guide also is intended to be a repository of best practices found throughout the agency

497

Test and Test Equipment Joshua Lottich  

E-Print Network (OSTI)

Test and Test Equipment Joshua Lottich CMPE 640 11/23/05 #12;Testing Verifies that manufactured chip meets design specifications. Cannot test for every potential defect. Modeling defects as faults allows for passing and failing of chips. Ideal test would capture all defects and pass only chips

Patel, Chintan