National Library of Energy BETA

Sample records for temperature surveys dead

  1. Boom And Bust With The Latest 2M Temperature Surveys- Dead Horse...

    Open Energy Info (EERE)

    of the use of two-meter temperature (2m) surveys to quickly and inexpensively reveal blind geothermal systems were documented at Dead Horse Wells, the Hawthorne Army Depot, and...

  2. Category:Static Temperature Survey | Open Energy Information

    Open Energy Info (EERE)

    Static Temperature Survey Jump to: navigation, search Geothermalpower.jpg Looking for the Static Temperature Survey page? For detailed information on Static Temperature Survey,...

  3. Line Focus Receiver Infrared Temperature Survey System

    Energy Science and Technology Software Center (OSTI)

    2010-06-01

    For ongoing maintenance and performance purposes, solar parabolic trough field operators desire to know that the Heat Collection Elements (HCEs) are performing properly. Measuring their temperature is one way of doing this One 30MW field can contain approximately 10,000 HCE's. This software interfaces with a GPS receiver and an infrared camera. It takes global positioning data from the GPS and uses this information to automate the infrared image capture and temperature analysis of individual solarmore » parabolic HCEs in a solar parabolic trough field With this software system an entire 30MW field can be surveyed in 2-3 days.« less

  4. Shallow (2-meter) temperature surveys in Colorado

    SciTech Connect (OSTI)

    Zehner, Richard E.

    2012-02-01

    Citation Information: Originator: Geothermal Development Associates, Reno, Nevada Publication Date: 2012 Title: Colorado 2m Survey Edition: First Publication Information: Publication Place: Reno Nevada Publisher: Geothermal Development Associates, Reno, Nevada Description: Shallow temperature surveys are useful in early-stage geothermal exploration to delineate surface outflow zones, with the intent to identify the source of upwelling, usually a fault. Detailed descriptions of the 2-meter survey method and equipment design can be found in Coolbaugh et al. (2007) and Sladek et al. (2007), and are summarized here. The survey method was devised to measure temperature as far below the zone of solar influence as possible, have minimal equilibration time, and yet be portable enough to fit on the back of an all-terrain vehicle (ATV); Figure 2). This method utilizes a direct push technology (DPT) technique where 2.3 m long, 0.54 outer diameter hollow steel rods are pounded into the ground using a demolition hammer. Resistance temperature devices (RTD) are then inserted into the rods at 2-meter depths, and allowed to equilibrate for one hour. The temperatures are then measured and recorded, the rods pulled out of the ground, and re-used at future sites. Usually multiple rods are planted over the course of an hour, and then the sampler returns back to the first station, measures the temperatures, pulls the rods, and so on, to eliminate waiting time. At Wagon Wheel Gap, 32 rods were planted around the hot springs between June 20 and July 1, 2012. The purpose was to determine the direction of a possible upflow fault or other structure. Temperatures at 1.5m and 2m depths were measured and recorded in the attribute table of this point shapefile. Several anomalous temperatures suggest that outflow is coming from a ~N60W striking fault or shear zone that contains the quartz-fluorite-barite veins of the adjacent patented mining claims. It should be noted that temperatures at 2m depth vary according to the amount of solar heating from above, as well as possible geothermal heating from below. Spatial Domain: Extent: Top: 4490310.560635 m Left: 150307.008238 m Right: 433163.213617 m Bottom: 4009565.915398 m Contact Information: Contact Organization: Geothermal Development Associates, Reno, Nevada Contact Person: Richard Rick Zehner Address: 3740 Barron Way City: Reno State: NV Postal Code: 89511 Country: USA Contact Telephone: 775-737-7806 Spatial Reference Information: Coordinate System: Universal Transverse Mercator (UTM) WGS1984 Zone 13N False Easting: 500000.00000000 False Northing: 0.00000000 Central Meridian: -105.00000000 Scale Factor: 0.99960000 Latitude of Origin: 0.00000000 Linear Unit: Meter Datum: World Geodetic System 1984 (WGS 1984) Prime Meridian: Greenwich Angular Unit: Degree Digital Form: Format Name: Shape file

  5. Static Temperature Survey At Rio Grande Rift Region (Morgan,...

    Open Energy Info (EERE)

    Temperature Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes San Luis Basin (south-central CO) regional study. References Paul Morgan, Peter Barkmann,...

  6. Static Temperature Survey At San Andreas Region (Williams, Et...

    Open Energy Info (EERE)

    San Andreas Region (Williams, Et Al., 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Static Temperature Survey At San Andreas Region...

  7. Effectiveness of Shallow Temperatures Surveys to Target a Geothermal...

    Open Energy Info (EERE)

    Effectiveness of Shallow Temperatures Surveys to Target a Geothermal Reservoir at Previously Explored Site at Mcgee Mountain, Nevada Jump to: navigation, search OpenEI Reference...

  8. Static Temperature Survey At Glass Buttes Area (DOE GTP) | Open...

    Open Energy Info (EERE)

    to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Static Temperature Survey At Glass Buttes Area (DOE GTP) Exploration Activity Details Location Glass...

  9. Static Temperature Survey At Medicine Lake Area (Warpinski, Et...

    Open Energy Info (EERE)

    GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Static Temperature Survey At Medicine Lake Area (Warpinski, Et Al., 2002) Exploration Activity Details Location Medicine...

  10. Static Temperature Survey At Chena Area (Erkan, Et. Al., 2008...

    Open Energy Info (EERE)

    Static Temperature Survey Activity Date Usefulness useful DOE-funding Unknown Notes Once a hole is drilled the natural-state pressure distribution with depth is essentially...

  11. Static Temperature Survey At Blue Mountain Geothermal Area (Fairbank...

    Open Energy Info (EERE)

    Blue Mountain Geothermal Area (Fairbank Engineering Ltd, 2003) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Static Temperature Survey At Blue...

  12. Static Temperature Survey At Maui Area (DOE GTP) | Open Energy...

    Open Energy Info (EERE)

    Maui Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Static Temperature Survey At Maui Area (DOE GTP) Exploration Activity Details...

  13. Static Temperature Survey At Wister Area (DOE GTP) | Open Energy...

    Open Energy Info (EERE)

    Wister Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Static Temperature Survey At Wister Area (DOE GTP) Exploration Activity...

  14. Static Temperature Survey At Medicine Lake Area (Warpinski, Et...

    Open Energy Info (EERE)

    Static Temperature Survey Activity Date Usefulness useful DOE-funding Unknown Notes Update to Warpinski, et al., 2002 References N. R. Warpinski, A. R. Sattler, R. Fortuna, D....

  15. Static Temperature Survey At Fish Lake Valley Area (Deymonaz...

    Open Energy Info (EERE)

    Fish Lake Valley Area (Deymonaz, Et Al., 2008) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Static Temperature Survey At Fish Lake Valley Area...

  16. First high-temperature electronics products survey 2005.

    SciTech Connect (OSTI)

    Normann, Randy Allen

    2006-04-01

    On April 4-5, 2005, a High-Temperature Electronics Products Workshop was held. This workshop engaged a number of governmental and private industry organizations sharing a common interest in the development of commercially available, high-temperature electronics. One of the outcomes of this meeting was an agreement to conduct an industry survey of high-temperature applications. This report covers the basic results of this survey.

  17. Static Temperature Survey | Open Energy Information

    Open Energy Info (EERE)

    2003. Estimation of static formation temperatures in geothermal wells. Energy conversion and management. 44(8):1343-1355. Page Area Activity Start Date Activity...

  18. Maine Geological Survey Borehole Temperature Profiles

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Marvinney, Robert

    2013-11-06

    This dataset includes temperature profiles from 30 boreholes throughout Maine that were selected for their depth, location, and lithologies encountered. Depths range from about 300 feet to 2,200 feet. Most of the boreholes selected for measurement were completed in granite because this lithology can be assumed to be nearly homogeneous over the depth of the borehole. Boreholes were also selected to address gaps in existing geothermal datasets. Temperature profiles were collected in October and November, 2012.

  19. Maine Geological Survey Borehole Temperature Profiles

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Marvinney, Robert

    This dataset includes temperature profiles from 30 boreholes throughout Maine that were selected for their depth, location, and lithologies encountered. Depths range from about 300 feet to 2,200 feet. Most of the boreholes selected for measurement were completed in granite because this lithology can be assumed to be nearly homogeneous over the depth of the borehole. Boreholes were also selected to address gaps in existing geothermal datasets. Temperature profiles were collected in October and November, 2012.

  20. Static Temperature Survey At Vale Hot Springs Area (Combs, Et...

    Open Energy Info (EERE)

    temperature gradient. After the hole reached TD, a pressure-temperature storage ("memory") tool was also used to compare temperature data with that previously taken by the PRT...

  1. Static Temperature Survey At Hot Pot Area (DOE GTP) | Open Energy...

    Open Energy Info (EERE)

    Hot Pot Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Static Temperature Survey At Hot Pot Area (DOE GTP) Exploration Activity...

  2. Static Temperature Survey At U.S. South Region (Smith & Dees...

    Open Energy Info (EERE)

    U.S. South Region (Smith & Dees, 1982) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Static Temperature Survey At U.S. South Region (Smith &...

  3. Effect of Dead Algae on Soil Permeability

    SciTech Connect (OSTI)

    Harvey, R.S.

    2003-02-21

    Since existing basins support heavy growths of unicellular green algae which may be killed by temperature variation or by inadvertent pH changes in waste and then deposited on the basin floor, information on the effects of dead algae on soil permeability was needed. This study was designed to show the effects of successive algal kills on the permeability of laboratory soil columns.

  4. Static Temperature Survey At Newberry Caldera Area (Combs, Et...

    Open Energy Info (EERE)

    temperature measurements. These temperature logs were taken with Sandia's platinum-resistance-thermometer (PRT) tool which along with a Sandia logging truck remained on-site for...

  5. Dead-time compensation for a logarithmic display rate meter

    DOE Patents [OSTI]

    Larson, John A.; Krueger, Frederick P.

    1988-09-20

    An improved circuit is provided for application to a radiation survey meter that uses a detector that is subject to dead time. The circuit compensates for dead time over a wide range of count rates by producing a dead-time pulse for each detected event, a live-time pulse that spans the interval between dead-time pulses, and circuits that average the value of these pulses over time. The logarithm of each of these values is obtained and the logarithms are subtracted to provide a signal that is proportional to a count rate that is corrected for the effects of dead time. The circuit produces a meter indication and is also capable of producing an audible indication of detected events.

  6. Dead-time compensation for a logarithmic display rate meter

    DOE Patents [OSTI]

    Larson, J.A.; Krueger, F.P.

    1987-10-05

    An improved circuit is provided for application to a radiation survey meter that uses a detector that is subject to dead time. The circuit compensates for dead time over a wide range of count rates by producing a dead-time pulse for each detected event, a live-time pulse that spans the interval between dead-time pulses, and circuits that average the value of these pulses over time. The logarithm of each of these values is obtained and the logarithms are subtracted to provide a signal that is proportional to a count rate that is corrected for the effects of dead time. The circuit produces a meter indication and is also capable of producing an audible indication of detected events. 5 figs.

  7. Static Temperature Survey At Long Valley Caldera Geothermal Area...

    Open Energy Info (EERE)

    beneath the resurgent dome. References Christopher Farrar, Jacob DeAngelo, Colin Williams, Frederick Grubb, Shaul Hurwitz (2010) Temperature Data From Wells in Long Valley...

  8. Static Temperature Survey At Coso Geothermal Area (1977) | Open...

    Open Energy Info (EERE)

    and 2775 feet. Temperature logs indicate a negative thermal gradient below 3000 feet. Water chemistry indicates that this geothermal resource is a hot-water rather than a...

  9. Static Temperature Survey At Long Valley Caldera Geothermal Area...

    Open Energy Info (EERE)

    Long Valley caldera groundwater system based on detailed integration of results from pump tests, fluid level monitoring, temperature logging, and fluid samplinganalysis of the...

  10. Static Temperature Survey At Kilauea East Rift Geothermal Area...

    Open Energy Info (EERE)

    create computer simulations of the heat flow patterns in the East Rift Zone References Albert J. Rudman, David Epp (1983) Conduction Models Of The Temperature Distribution In The...

  11. Static Temperature Survey At Reese River Area (Henkle & Ronne...

    Open Energy Info (EERE)

    Usefulness not indicated DOE-funding Unknown Notes Temperature logs were run on well 56-4 on March 22, April 28 and Nov. 9, 2007. The respective maximum bottom hole...

  12. Static Temperature Survey At Steamboat Springs Area (Combs, Et...

    Open Energy Info (EERE)

    DOE-funding Unknown Notes Numerous temperature logs were taken with Sandia'splatinum-resistance-thermometer (PRT) tool which along with a Sandia logging truck remained on-site for...

  13. Zero dead volume tube to surface seal

    DOE Patents [OSTI]

    Benett, William J.; Folta, James A.

    2000-01-01

    A method and apparatus for connecting a tube to a surface that creates a dead volume seal. The apparatus is composed of three components, a body, a ferrule, and a threaded fitting. The ferrule is compressed onto a tube and a seal is formed between the tube and a device retained in the body by threading the fitting into the body which provides pressure that seals the face of the ferrule to a mating surface on the device. This seal can be used at elevated temperatures depending on the materials used. While the invention has been developed for use with micro-machined silicon wafers used in Capillary Gas Chromatograph (GC), it can be utilized anywhere for making a gas or fluid face seal to the surface of a device that has near zero dead volume.

  14. Dead Horse Geothermal Project | Open Energy Information

    Open Energy Info (EERE)

    Horse Geothermal Project Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Development Project: Dead Horse Geothermal Project Project Location Information...

  15. MAGNETIZED ACCRETION AND DEAD ZONES IN PROTOSTELLAR DISKS

    SciTech Connect (OSTI)

    Dzyurkevich, Natalia; Henning, Thomas; Turner, Neal J.; Kley, Wilhelm

    2013-03-10

    The edges of magnetically dead zones in protostellar disks have been proposed as locations where density bumps may arise, trapping planetesimals and helping form planets. Magneto-rotational turbulence in magnetically active zones provides both accretion of gas on the star and transport of mass to the dead zone. We investigate the location of the magnetically active regions in a protostellar disk around a solar-type star, varying the disk temperature, surface density profile, and dust-to-gas ratio. We also consider stellar masses between 0.4 and 2 M{sub Sun }, with corresponding adjustments in the disk mass and temperature. The dead zone's size and shape are found using the Elsasser number criterion with conductivities including the contributions from ions, electrons, and charged fractal dust aggregates. The charged species' abundances are found using the approach proposed by Okuzumi. The dead zone is in most cases defined by the ambipolar diffusion. In our maps, the dead zone takes a variety of shapes, including a fish tail pointing away from the star and islands located on and off the midplane. The corresponding accretion rates vary with radius, indicating locations where the surface density will increase over time, and others where it will decrease. We show that density bumps do not readily grow near the dead zone's outer edge, independently of the disk parameters and the dust properties. Instead, the accretion rate peaks at the radius where the gas-phase metals freeze out. This could lead to clearing a valley in the surface density, and to a trap for pebbles located just outside the metal freezeout line.

  16. Surveys

    Broader source: Energy.gov [DOE]

    Surveys can be a useful way to gauge the opinions of your readers and learn more about your website's audiences, but you'll often need approval from the Office of Management and Budget (OMB) to run...

  17. Dead-time Corrected Disdrometer Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Bartholomew, Mary Jane

    2008-03-05

    Original and dead-time corrected disdrometer results for observations made at SGP and TWP. The correction is based on the technique discussed in Sheppard and Joe, 1994. In addition, these files contain calculated radar reflectivity factor, mean Doppler velocity and attenuation for every measurement for both the original and dead-time corrected data at the following wavelengths: 0.316, 0.856, 3.2, 5, and 10cm (W,K,X,C,S bands). Pavlos Kollias provided the code to do these calculations.

  18. An In-Cylinder Imaging Survey of Low-Temperature, High-Efficiency...

    Broader source: Energy.gov (indexed) [DOE]

    High speed imaging of in-cylinder spray and combustion luminosity of low temperature combustion strategies are contrasted to conventional gasoline and diesel engine combustion PDF ...

  19. An In-Cylinder Imaging Survey of Low-Temperature, High-Efficiency Combustion Strategies

    Broader source: Energy.gov [DOE]

    High speed imaging of in-cylinder spray and combustion luminosity of low temperature combustion strategies are contrasted to conventional gasoline and diesel engine combustion

  20. CCP Art. 49 Inquests upon dead bodies | Open Energy Information

    Open Energy Info (EERE)

    CCP Art. 49 Inquests upon dead bodies Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- RegulationRegulation: CCP Art. 49 Inquests upon dead...

  1. A SYSTEMATIC SURVEY OF HIGH-TEMPERATURE EMISSION IN SOLAR ACTIVE REGIONS

    SciTech Connect (OSTI)

    Warren, Harry P.; Winebarger, Amy R.; Brooks, David H.

    2012-11-10

    The recent analysis of observations taken with the EUV Imaging Spectrometer and X-Ray Telescope instruments on Hinode suggests that well-constrained measurements of the temperature distribution in solar active regions can finally be made. Such measurements are critical for constraining theories of coronal heating. Past analysis, however, has suffered from limited sample sizes and large uncertainties at temperatures between 5 and 10 MK. Here we present a systematic study of the differential emission measure distribution in 15 active region cores. We focus on measurements in the 'inter-moss' region, that is, the region between the loop footpoints, where the observations are easier to interpret. To reduce the uncertainties at the highest temperatures we present a new method for isolating the Fe XVIII emission in the AIA/SDO 94 A channel. The resulting differential emission measure distributions confirm our previous analysis showing that the temperature distribution in an active region core is often strongly peaked near 4 MK. We characterize the properties of the emission distribution as a function of the total unsigned magnetic flux. We find that the amount of high-temperature emission in the active region core is correlated with the total unsigned magnetic flux, while the emission at lower temperatures, in contrast, is inversely related. These results provide compelling evidence that high-temperature active region emission is often close to equilibrium, although weaker active regions may be dominated by evolving million degree loops in the core.

  2. Employee Surveys

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Employee Surveys

  3. Very High Temperature Reactor (VHTR) Survey of Materials Research and Development Needs to Support Early Deployment

    SciTech Connect (OSTI)

    Eric Shaber; G. Baccaglini; S. Ball; T. Burchell; B. Corwin; T. Fewell; M. Labar; P. MacDonald; P. Rittenhouse; Russ Vollam; F. Southworth

    2003-01-01

    The VHTR reference concept is a helium-cooled, graphite moderated, thermal neutron spectrum reactor with an outlet temperature of 1000 C or higher. It is expected that the VHTR will be purchased in the future as either an electricity producing plant with a direct cycle gas turbine or a hydrogen producing (or other process heat application) plant. The process heat version of the VHTR will require that an intermediate heat exchanger (IHX) and primary gas circulator be located in an adjoining power conversion vessel. A third VHTR mission - actinide burning - can be accomplished with either the hydrogen-production or gas turbine designs. The first ''demonstration'' VHTR will produce both electricity and hydrogen using the IHX to transfer the heat to either a hydrogen production plant or the gas turbine. The plant size, reactor thermal power, and core configuration will be designed to assure passive decay heat removal without fuel damage during accidents. The fuel cycle will be a once-through very high burnup low-enriched uranium fuel cycle. The purpose of this report is to identify the materials research and development needs for the VHTR. To do this, we focused on the plant design described in Section 2, which is similar to the GT-MHR plant design (850 C core outlet temperature). For system or component designs that present significant material challenges (or far greater expense) there may be some viable design alternatives or options that can reduce development needs or allow use of available (cheaper) materials. Nevertheless, we were not able to assess those alternatives in the time allotted for this report and, to move forward with this material research and development assessment, the authors of this report felt that it was necessary to use a GT-MHR type design as the baseline design.

  4. Dead Reckoning Pedometer Graphical User Interface

    Energy Science and Technology Software Center (OSTI)

    2003-04-26

    The Dead Reckoning Pedometer Graphical User Interface (DRP GUI) software is tasked with maturing the technology described in a WSRC patent application. This patent application describes an electronic navigation system that records human foot movements, in three dimensions, for the purpose of determining position, distance, and speed of a walking person. The simiplest form of the apparatus consists of a magnetometer (an instrument that measures magnetic field strength) on one foot and a small permanentmore » magnet on another foot with pressure sensors on each foot. When a person takes a step, the foot will hit the ground and produce a signal on the pressure sensor. This will trigger a reading of the magnetometer so that the relative position of one foot to the other can be calculated. This same process is repeated for each step. The DRP could be very useful for tracking emergency personnel such as firemen, policemen, and paramedics when they travel within a building. Technologies such as global positioning systems to not work within buildings. The goal of the DRP GUI V1.0.0 software is to provide a three-dimensional graphical user interface that will allow WSRC to demonstrate the DRP concepts to potential patent licensees. It is hoped that a partnership will allow WSRC and another company to further develop the DRP technology and software into a commercial product.« less

  5. Trails and Dead Bodies: Directly Characterizing Extrasolar Planets...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Trails and Dead Bodies: Directly Characterizing Extrasolar Planets with Adaptive Optics October 2, 2015 11:00AM to 12:00PM Presenter Mark Ammons, Lawrence Livermore National...

  6. TCCP 49 - Inquests Upon Dead Bodies | Open Energy Information

    Open Energy Info (EERE)

    - Inquests Upon Dead BodiesLegal Published NA Year Signed or Took Effect 1987 Legal Citation TCCP 49 (1987) DOI Not Provided Check for DOI availability: http:crossref.org...

  7. Reviving Algae from the (Almost) Dead - News Feature | NREL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reviving Algae from the (Almost) Dead October 31, 2014 Photo of a man in a lab coat standing next to green algae bubbling in containers. NREL Research Technician Nick Sweeney...

  8. ARM - PI Product - Dead-time Corrected Disdrometer Data

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ProductsDead-time Corrected Disdrometer Data ARM Data Discovery Browse Data Comments? We would love to hear from you Send us a note below or call us at 1-888-ARM-DATA. Send PI...

  9. Effectiveness of Shallow Temperatures Surveys to Target a Geothermal Reservoir at Previously Explored Sites at McGee Mountain, Nevada

    Broader source: Energy.gov [DOE]

    DOE Geothermal Peer Review 2010 - Presentation. Project Objectives: To evaluate the cost-effectiveness of two innovative technologies in early-stage geothermal exploration:a) shallow (2m) survey; b) hydroprobe; and Identify a geothermal resource at the project site.

  10. Reviving Algae from the (Almost) Dead - News Feature | NREL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reviving Algae from the (Almost) Dead October 31, 2014 Photo of a man in a lab coat standing next to green algae bubbling in containers. NREL Research Technician Nick Sweeney inoculates algae being grown in a tent reactor. Algae brought back to active states from cryogenic tanks need aerobic environments to meet their full potential as biofuels. Photo by Dennis Schroeder, NREL Tucked away in darkness and almost dead, algae can emerge from a frigid and foggy environment to live again-and perhaps

  11. Dead Zones in LX-17 and PBX 9502

    SciTech Connect (OSTI)

    Souers, P C; Andreski, H G; Batteux, J; Bratton, B; Cabacungan, C; Cook, III, C F; Fletcher, S; Garza, R; Grimsley, D; Handly, J; Hernandez, A; McMaster, P; Molitoris, J D; Palmer, R; Prindiville, J; Rodriguez, J; Schneberk, D; Wong, B; Vitello, P

    2005-09-06

    Pin and X-ray corner-turning data have been taken on ambient LX-17 and PBX 9052, and the results are listed in tables as an aid to future modeling. The results have been modeled at 4 zones/mm with a reactive flow approach that varies the burn rate as a function of pressure. A single rate format is used to simulate failure and detonation in different pressure regimes. A pressure cut-off must also be reached to initiate the burn. Corner-turning and failure are modeled using an intermediate pressure rate region, and detonation occurs at high pressure. The TATB booster is also modeled using reactive flow, and X-ray tomography is used to partition the ram-pressed hemisphere into five different density regions. The model reasonably fits the bare corner-turning experiment but predicts a smaller dead zone with steel confinement, in contradiction with experiment. The same model also calculates the confined and unconfined cylinder detonation velocities and predicts the failure of the unconfined cylinder at 3.75 mm radius. The PBX 9502 shows a smaller dead zone than LX-17. An old experiment that showed a large apparent dead zone in Comp B was repeated with X-ray transmission and no dead zone was seen. This confirms the idea that a variable burn rate is the key to modeling. The model also produces initiation delays, which are shorter than those found in time-to-detonation.

  12. How Long Has Grandpa Been Dead and Other Forensic Mysteries

    ScienceCinema (OSTI)

    Baden, Michael [MD, New York Police, New York, New York, United States

    2009-09-01

    Was the baby born alive? Can a child's brain really be shaken hard enough to cause death? Was the body dead before going into the water? Does a lightening strike cause any unique changes in the body? Why are hair and maggots becoming so important to the forensic scientist? Let's talk.

  13. FORMATION OF CIRCUMBINARY PLANETS IN A DEAD ZONE

    SciTech Connect (OSTI)

    Martin, Rebecca G.; Armitage, Philip J. [JILA, University of Colorado and NIST, UCB 440, Boulder, CO 80309 (United States); Alexander, Richard D. [Department of Physics and Astronomy, University of Leicester, Leicester LE1 7RH (United Kingdom)

    2013-08-10

    Circumbinary planets have been observed at orbital radii where binary perturbations may have significant effects on the gas disk structure, on planetesimal velocity dispersion, and on the coupling between turbulence and planetesimals. Here, we note that the impact of all of these effects on planet formation is qualitatively altered if the circumbinary disk structure is layered, with a non-turbulent midplane layer (dead zone) and strongly turbulent surface layers. For close binaries, we find that the dead zone typically extends from a radius close to the inner disk edge up to a radius of around 10-20 AU from the center of mass of the binary. The peak in the surface density occurs within the dead zone, far from the inner disk edge, close to the snow line, and may act as a trap for aerodynamically coupled solids. We suggest that circumbinary planet formation may be easier near this preferential location than for disks around single stars. However, dead zones around wide binaries are less likely, and hence planet formation may be more difficult there.

  14. THE ROLE OF DEAD WOOD IN MAINTAINING ARTHROPOD DIVERSITY ON THE FOREST FLOOR.

    SciTech Connect (OSTI)

    Hanula, James L.; Horn, Scott; Wade, Dale D.

    2006-08-01

    AbstractDead wood is a major component of forests and contributes to overall diversity, primarily by supporting insects that feed directly on or in it. Further, a variety of organisms benefit by feeding on those insects. What is not well known is how or whether dead wood influences the composition of the arthropod community that is not solely dependent on it as a food resource, or whether woody debris influences prey available to generalist predators. One group likely to be affected by dead wood is ground-dwelling arthropods. We studied the effect of adding large dead wood to unburned and frequently burned pine stands to determine if dead wood was used more when the litter and understory plant community are removed. We also studied the effect of annual removal of dead wood from large (10-ha) plots over a 5-year period on ground-dwelling arthropods. In related studies, we examined the relationships among an endangered woodpecker that forages for prey on live trees, its prey, and dead wood in the forest. The results of these and other studies show that dead wood can influence the abundance and diversity of the ground-dwelling arthropod community and of prey available to generalist predators not foraging directly on dead trees.

  15. 2-M Probe At Dead Horse Wells Area (Kratt, Et Al., 2010) | Open...

    Open Energy Info (EERE)

    Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: 2-M Probe At Dead Horse Wells Area (Kratt, Et Al., 2010) Exploration Activity Details...

  16. Metagenome of a Versatile Chemolithoautotroph from Expanding Oceanic Dead Zones

    SciTech Connect (OSTI)

    Walsh, David A.; Zaikova, Elena; Howes, Charles L.; Song, Young; Wright, Jody; Tringe, Susannah G.; Tortell, Philippe D.; Hallam, Steven J.

    2009-07-15

    Oxygen minimum zones (OMZs), also known as oceanic"dead zones", are widespread oceanographic features currently expanding due to global warming and coastal eutrophication. Although inhospitable to metazoan life, OMZs support a thriving but cryptic microbiota whose combined metabolic activity is intimately connected to nutrient and trace gas cycling within the global ocean. Here we report time-resolved metagenomic analyses of a ubiquitous and abundant but uncultivated OMZ microbe (SUP05) closely related to chemoautotrophic gill symbionts of deep-sea clams and mussels. The SUP05 metagenome harbors a versatile repertoire of genes mediating autotrophic carbon assimilation, sulfur-oxidation and nitrate respiration responsive to a wide range of water column redox states. Thus, SUP05 plays integral roles in shaping nutrient and energy flow within oxygen-deficient oceanic waters via carbon sequestration, sulfide detoxification and biological nitrogen loss with important implications for marine productivity and atmospheric greenhouse control.

  17. Ch. VII, Temperature, heat flow maps and temperature gradient...

    Open Energy Info (EERE)

    Report: Ch. VII, Temperature, heat flow maps and temperature gradient holes Author T. G. Zacharakis Editor T. G. Zacharakis Published Colorado Geological Survey in Cooperation...

  18. Temperature, heat flow maps and temperature gradient holes |...

    Open Energy Info (EERE)

    to library Report: Temperature, heat flow maps and temperature gradient holes Author T. G. Zacharakis Organization Colorado Geological Survey in Cooperation with the U.S....

  19. A grateful dead analysis: the relationship between concert and listening behavior

    SciTech Connect (OSTI)

    Rodriguez, Marko A; Gintautas, Vadas; Pepe, Alberto

    2008-01-01

    The Grateful Dead was an American band born out of the 1960s San Francisco, California psychedelic movement, that played music together from 1965 to 1995. Despite relatively little popular radio airtime, while on tour the Grateful Dead enjoyed a cult-like following from a fan base that numbered in the millions. Still today, some ten years after dissolution, the band remains popular according to online music services, such as last.fm. This article presents a comparative analysis between 1,590 of the Grateful Dead's live concert set lists from 1972 to 1995 and 2,616,990 Grateful Dead listening events by last.fm users from August 2005 to October 2007. While there is a strong correlation between how songs were played in concert and how they were listened to by last.fm members, the outlying songs in this trend identify interesting aspects of the band and their present-day fans.

  20. Relationships between dead wood and arthropods in the Southeastern United States.

    SciTech Connect (OSTI)

    Ulyshen, Michael, Darragh

    2009-05-01

    The importance of dead wood to maintaining forest diversity is now widely recognized. However, the habitat associations and sensitivities of many species associated with dead wood remain unknown, making it difficult to develop conservation plans for managed forests. The purpose of this research, conducted on the upper coastal plain of South Carolina, was to better understand the relationships between dead wood and arthropods in the southeastern United States. In a comparison of forest types, more beetle species emerged from logs collected in upland pine-dominated stands than in bottomland hardwood forests. This difference was most pronounced for Quercus nigra L., a species of tree uncommon in upland forests. In a comparison of wood postures, more beetle species emerged from logs than from snags, but a number of species appear to be dependent on snags including several canopy specialists. In a study of saproxylic beetle succession, species richness peaked within the first year of death and declined steadily thereafter. However, a number of species appear to be dependent on highly decayed logs, underscoring the importance of protecting wood at all stages of decay. In a study comparing litter-dwelling arthropod abundance at different distances from dead wood, arthropods were more abundant near dead wood than away from it. In another study, grounddwelling arthropods and saproxylic beetles were little affected by large-scale manipulations of dead wood in upland pine-dominated forests, possibly due to the suitability of the forests surrounding the plots.

  1. Selected data for low-temperature (less than 90{sup 0}C) geothermal systems in the United States: reference data for US Geological Survey Circular 892

    SciTech Connect (OSTI)

    Reed, M.J.; Mariner, R.H.; Brook, C.A.; Sorey, M.L.

    1983-12-15

    Supporting data are presented for the 1982 low-temperature geothermal resource assessment of the United States. Data are presented for 2072 geothermal sites which are representative of 1168 low-temperature geothermal systems identified in 26 States. The low-temperature geothermal systems consist of 978 isolated hydrothermal-convection systems, 148 delineated-area hydrothermal-convection systems, and 42 delineated-area conduction-dominated systems. The basic data and estimates of reservoir conditions are presented for each geothermal system, and energy estimates are given for the accessible resource base, resource, and beneficial heat for each isolated system.

  2. Beowawe geothermal-resource assessment. Final report. Shallow-hole temperature survey geophysics and deep test hole Collins 76-17

    SciTech Connect (OSTI)

    Jones, N.O.

    1983-03-01

    Geothermal resource investigation field efforts in the Beowawe Geysers Area, Eureka County, Nevada are described. The objectives included acquisition of geotechnical data for understanding the nature and extent of the geothermal resource boundaries south of the known resource area. Fourteen shallow (<500 feet) temperature-gradient holes plus geophysics were used to select the site for a deep exploratory well, the Collins 76-17, which was completed to a total depth of 9005 feet. Maximum downhole recorded temperature was 311/sup 0/F, but no flow could be induced.

  3. Digital Surveying Directional Surveying Specialists | Open Energy...

    Open Energy Info (EERE)

    Surveying Specialists Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Digital Surveying Directional Surveying Specialists Author Directional Surveying...

  4. Dead layer on silicon p-i-n diode charged-particle detectors

    SciTech Connect (OSTI)

    Wall, B. L.; Amsbaugh, John F.; Beglarian, A.; Bergmann, T.; Bichsel, H. C.; Bodine, L. I.; Boyd, N. M.; Burritt, Tom H.; Chaoui, Z.; Corona, T. J.; Doe, Peter J.; Enomoto, S.; Harms, F.; Harper, Gregory; Howe, M. A.; Martin, E. L.; Parno, D. S.; Peterson, David; Petzold, Linda; Renschler, R.; Robertson, R. G. H.; Schwarz, J.; Steidl, M.; Van Wechel, T. D.; VanDevender, Brent A.; Wustling, S.; Wierman, K. J.; Wilkerson, J. F.

    2014-04-21

    Abstract Semiconductor detectors in general have a dead layer at their surfaces that is either a result of natural or induced passivation, or is formed during the process of making a contact. Charged particles passing through this region produce ionization that is incompletely collected and recorded, which leads to departures from the ideal in both energy deposition and resolution. The silicon p-i-n diode used in the KATRIN neutrinomass experiment has such a dead layer. We have constructed a detailed Monte Carlo model for the passage of electrons from vacuum into a silicon detector, and compared the measured energy spectra to the predicted ones for a range of energies from 12 to 20 keV. The comparison provides experimental evidence that a substantial fraction of the ionization produced in the "dead" layer evidently escapes by discussion, with 46% being collected in the depletion zone and the balance being neutralized at the contact or by bulk recombination. The most elementary model of a thinner dead layer from which no charge is collected is strongly disfavored.

  5. Monument Survey

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Photographs from the WIPP Permanent Marker Monument Survey John Hart & Associates, 2000 Photograph of the Gnome Marker located about 10 miles SW of the WIPP site For more...

  6. radiological. survey

    National Nuclear Security Administration (NNSA)

    7%2A en NNSA to Conduct Aerial Radiological Surveys Over San Francisco, Pacifica, Berkeley, And Oakland, CA Areas http:nnsa.energy.govmediaroompressreleasesamsca

  7. Survey Consumption

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    purchase diaries from a subset of respondents composing a Household Transportation Panel and is reported separately. Residential Energy Consumption Survey: Consumption and...

  8. 2-M Probe Survey | Open Energy Information

    Open Energy Info (EERE)

    Techniques A modified version of the 2 m temperature probe survey was tested at the Salt Wells Geothermal Area in 2005.2 This technique was used to measure temperatures at...

  9. Online Robot Dead Reckoning Localization Using Maximum Relative Entropy Optimization With Model Constraints

    SciTech Connect (OSTI)

    Urniezius, Renaldas

    2011-03-14

    The principle of Maximum relative Entropy optimization was analyzed for dead reckoning localization of a rigid body when observation data of two attached accelerometers was collected. Model constraints were derived from the relationships between the sensors. The experiment's results confirmed that accelerometers each axis' noise can be successfully filtered utilizing dependency between channels and the dependency between time series data. Dependency between channels was used for a priori calculation, and a posteriori distribution was derived utilizing dependency between time series data. There was revisited data of autocalibration experiment by removing the initial assumption that instantaneous rotation axis of a rigid body was known. Performance results confirmed that such an approach could be used for online dead reckoning localization.

  10. 2-M Probe Survey At Chena Geothermal Area (Wescott & Turner,...

    Open Energy Info (EERE)

    Basis Masters thesis Norma Biggar, Geophysical Institute University of Alaska Notes Ground temperature survey performed with a 0.5 m probe. This survey yielded a SE-trending...

  11. 2012 NERSC User Survey Text

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2012 User Survey Text 2010/2011 User Survey Results 2009/2010 User Survey Results 2008/2009 User Survey Results 2007/2008 User Survey Results 2006 User Survey Results 2005 User Survey Results 2004 User Survey Results 2003 User Survey Results 2002 User Survey Results 2001 User Survey Results 2000 User Survey Results 1999 User Survey Results 1998 User Survey Results HPC Requirements for Science HPC Workshop Reports NERSC Staff Publications & Presentations Journal Cover Stories Galleries

  12. Robotic Surveying

    SciTech Connect (OSTI)

    Suzy Cantor-McKinney; Michael Kruzic

    2007-03-01

    ZAPATA ENGINEERING challenged our engineers and scientists, which included robotics expertise from Carnegie Mellon University, to design a solution to meet our client's requirements for rapid digital geophysical and radiological data collection of a munitions test range with no down-range personnel. A prime concern of the project was to minimize exposure of personnel to unexploded ordnance and radiation. The field season was limited by extreme heat, cold and snow. Geographical Information System (GIS) tools were used throughout this project to accurately define the limits of mapped areas, build a common mapping platform from various client products, track production progress, allocate resources and relate subsurface geophysical information to geographical features for use in rapidly reacquiring targets for investigation. We were hopeful that our platform could meet the proposed 35 acres per day, towing both a geophysical package and a radiological monitoring trailer. We held our breath and crossed our fingers as the autonomous Speedrower began to crawl across the playa lakebed. We met our proposed production rate, and we averaged just less than 50 acres per 12-hour day using the autonomous platform with a path tracking error of less than +/- 4 inches. Our project team mapped over 1,800 acres in an 8-week (4 days per week) timeframe. The expertise of our partner, Carnegie Mellon University, was recently demonstrated when their two autonomous vehicle entries finished second and third at the 2005 Defense Advanced Research Projects Agency (DARPA) Grand Challenge. 'The Grand Challenge program was established to help foster the development of autonomous vehicle technology that will some day help save the lives of Americans who are protecting our country on the battlefield', said DARPA Grand Challenge Program Manager, Ron Kurjanowicz. Our autonomous remote-controlled vehicle (ARCV) was a modified New Holland 2550 Speedrower retrofitted to allow the machine-actuated functions to be controlled by an onboard computer. The computer-controlled Speedrower was developed at Carnegie Mellon University to automate agricultural harvesting. Harvesting tasks require the vehicle to cover a field using minimally overlapping rows at slow speeds in a similar manner to geophysical data acquisition. The Speedrower had demonstrated its ability to perform as it had already logged hundreds of acres of autonomous harvesting. This project is the first use of autonomous robotic technology on a large-scale for geophysical surveying.

  13. Cable Effects Study. Tangents, Rabbit Holes, Dead Ends, and Valuable Results

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Ardelean, Emil V.; Babuška, Vít; Goodding, James C.; Coombs, Douglas M.; Robertson, Lawrence M.; Lane, Steven A.

    2014-08-04

    Lessons learned during a study on the effects that electrical power and signal wiring harness cables introduce on the dynamic response of precision spacecraft is presented, along with the most significant results. Our study was a three year effort to discover a set of practical approaches for updating well-defined dynamic models of harness-free structures where knowledge of the cable type, position, and tie-down method are known. Although cables are found on every satellite, the focus was on precision, low damping, and very flexible structures. Obstacles encountered, classified as tangents, rabbit holes, and dead ends, offer practical lessons for structural dynamicsmore » research. The paper traces the historical, experiential progression of the project, describing how the obstacles affected the project. Methods were developed to estimate cable properties. Problems were encountered because of the flexible, highly damped nature of cables. A beam was used as a test article to validate experimentally derived cable properties and to refine the assumptions regarding boundary conditions. Furthermore, a spacecraft bus-like panel with cables attached was designed, and finite element models were developed and validated through experiment. Various paths were investigated at each stage before a consistent test and analysis methodology was developed« less

  14. Windrow co-composting of natural casings waste with sheep manure and dead leaves

    SciTech Connect (OSTI)

    Makan, Abdelhadi

    2015-08-15

    Highlights: • Waste management opportunities in small and medium companies were highlighted. • Pilot scale program for windrow co-composting of natural casings was investigated. • Compost preparation, characterization and application phases were discussed. • Natural casings co-composting has proved more viable and cost effective solution. - Abstract: After studying the waste management opportunities in small and medium companies of natural casings, composting has proved more viable and cost effective solution for the valorization of these types of waste, but its feasibility depends on the final product value. This paper investigated a pilot scale program for the windrow co-composting of natural casings waste with sheep manure and dead leaves incorporation. Processing, characterization and application of the final compost were described and the final compost was analyzed for pathogens, metals, nutrients, maturity, and agronomic parameters. The results showed that all test result levels were below the limits specified in the EPA regulations published in Title 40, Section 503, of the Code of Federal Regulations (40 CFR 503). Moreover, the agronomic value tests which include nutrients, organic matter, pH, electrical conductivity, etc. showed that the compost had high organic-matter content and low salt content, all of which indicate good compost characteristics. The ratio of nitrogen (N), phosphorus (P), and potassium (K), or NPK ratio, was measured at 1.6–0.9–0.7. Reported units are consistent with those found on fertilizer formulations.

  15. Cable Effects Study. Tangents, Rabbit Holes, Dead Ends, and Valuable Results

    SciTech Connect (OSTI)

    Ardelean, Emil V.; Babuška, Vít; Goodding, James C.; Coombs, Douglas M.; Robertson, Lawrence M.; Lane, Steven A.

    2014-08-04

    Lessons learned during a study on the effects that electrical power and signal wiring harness cables introduce on the dynamic response of precision spacecraft is presented, along with the most significant results. Our study was a three year effort to discover a set of practical approaches for updating well-defined dynamic models of harness-free structures where knowledge of the cable type, position, and tie-down method are known. Although cables are found on every satellite, the focus was on precision, low damping, and very flexible structures. Obstacles encountered, classified as tangents, rabbit holes, and dead ends, offer practical lessons for structural dynamics research. The paper traces the historical, experiential progression of the project, describing how the obstacles affected the project. Methods were developed to estimate cable properties. Problems were encountered because of the flexible, highly damped nature of cables. A beam was used as a test article to validate experimentally derived cable properties and to refine the assumptions regarding boundary conditions. Furthermore, a spacecraft bus-like panel with cables attached was designed, and finite element models were developed and validated through experiment. Various paths were investigated at each stage before a consistent test and analysis methodology was developed

  16. SRS 2010 Vegetation Inventory GeoStatistical Mapping Results for Custom Reaction Intensity and Total Dead Fuels.

    SciTech Connect (OSTI)

    Edwards, Lloyd A.; Paresol, Bernard

    2014-09-01

    This report of the geostatistical analysis results of the fire fuels response variables, custom reaction intensity and total dead fuels is but a part of an SRS 2010 vegetation inventory project. For detailed description of project, theory and background including sample design, methods, and results please refer to USDA Forest Service Savannah River Site internal report “SRS 2010 Vegetation Inventory GeoStatistical Mapping Report”, (Edwards & Parresol 2013).

  17. STEP Participant Survey Report

    Broader source: Energy.gov [DOE]

    STEP Participant Survey Report, from the Tool Kit Framework: Small Town University Energy Program (STEP).

  18. DEAD, UNDEAD, AND ZOMBIE ZONES IN PROTOSTELLAR DISKS AS A FUNCTION OF STELLAR MASS

    SciTech Connect (OSTI)

    Mohanty, Subhanjoy; Ercolano, Barbara; Turner, Neal J. E-mail: ercolano@usm.lmu.de

    2013-02-10

    We investigate the viability of the magnetorotational instability (MRI) in X-ray ionized viscous accretion disks around both solar-type stars and very low mass stars. In particular, we determine the disk regions where the MRI can be shut off either by Ohmic resistivity (the so-called dead and undead zones) or by ambipolar diffusion (a region we term the zombie zone). We consider two stellar masses: M {sub *} = 0.7 M {sub Sun} and 0.1 M {sub Sun }. In each case, we assume that: the disk surface density profile is that of a scaled Minimum Mass Solar Nebula, with M {sub disk}/M {sub *} = 0.01 as suggested by current data; disk ionization is driven primarily by stellar X-rays, complemented by cosmic rays and radionuclides; and the stellar X-ray luminosity scales with bolometric luminosity as L{sub X} /L {sub *} Almost-Equal-To 10{sup -3.5}, as observed. Ionization rates are calculated with the MOCCASIN Monte Carlo X-ray transport code, and ionization balance determined using a simplified chemical network, including well-mixed 0.1 {mu}m grains at various levels of depletion. We find that (1) ambipolar diffusion is the primary factor controlling MRI activity in disks around both solar-type and very low mass classical T Tauri stars. Assuming that the MRI yields the maximum possible field strength at each radius, we further find that: (2) the MRI-active layer constitutes only {approx}5%-10% of the total disk mass; (3) the accretion rate ( M-dot ) varies radially in both magnitude and sign (inward or outward), implying time-variable accretion as well as the creation of disk gaps and overdensities, with consequences for planet formation and migration; (4) achieving the empirical accretion rates in solar-type and very low mass stars requires a depletion of well-mixed small grains (via grain growth and/or settling) by a factor of 10-1000 relative to the standard dust-to-gas mass ratio of 10{sup -2}; and (5) the current non-detection of polarized emission from field-aligned grains in the outer disk regions is consistent with active MRI at those radii.

  19. NEPA Litigation Surveys

    Broader source: Energy.gov [DOE]

    CEQ publishes surveys on NEPA litigation on an annual basis. These surveys identify the number of cases involving a NEPA based cause of action, Federal agencies that were identified as a lead...

  20. 2002 Manufacturing Energy Consumption Survey - User Needs Survey

    U.S. Energy Information Administration (EIA) Indexed Site

    2002 Manufacturing Energy Consumption Survey: User-Needs Survey View current results. We need your help in designing the next Energy Consumption Survey (MECS) As our valued...

  1. Improvements in Shallow (Two-Meter) Temperature Measurements...

    Open Energy Info (EERE)

    Center for Geothermal Energy has been working on improvements in shallow (two-meter) temperature surveys in two areas: overcoming limitations posed by difficult ground...

  2. AASG State Geological Survey

    Broader source: Energy.gov [DOE]

    presentation at the April 2013 peer review meeting held in Denver, Colorado.Contributions to the NGDSAASG State Geological Survey

  3. ORISE: Characterization surveys

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Characterization surveys An ORISE technicians performs a characterization survey The Oak Ridge Institute for Science and Education (ORISE) performs independent, objective characterization surveys to define the extent of radiological contamination at sites scheduled for decontamination and decommissioning (D&D). A fundamental aspect of all D&D projects, characterization surveys provide guidance to determine the best remediation procedures and are a cost-effective method of ensuring a site

  4. Temperature System

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1 Soil Water and Temperature System  SWATS In the realm of global climate modeling, numerous variables affect the state of the atmosphere and climate. One important area is soil moisture and temperature. The ARM Program uses several types of instruments to gather soil moisture information. An example is the soil water and temperature system (SWATS) (Figure 1). A SWATS is located at each of 21 extended facility sites within the CART site boundary. Each system is configured to measure soil

  5. Environmental Survey preliminary report

    SciTech Connect (OSTI)

    Not Available

    1988-04-01

    This report presents the preliminary findings from the first phase of the Environmental Survey of the United States Department of Energy (DOE) Sandia National Laboratories conducted August 17 through September 4, 1987. The objective of the Survey is to identify environmental problems and areas of environmental risk associated with Sandia National Laboratories-Albuquerque (SNLA). The Survey covers all environmental media and all areas of environmental regulation. It is being performed in accordance with the DOE Environmental Survey Manual. This phase of the Survey involves the review of existing site environmental data, observations of the operations carried on at SNLA, and interviews with site personnel. 85 refs., 49 figs., 48 tabs.

  6. 2014 NERSC User Survey

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    User Survey 2014 NERSC User Survey December 17, 2014 by Francesca Verdier Please take a few minutes to fill out NERSC's annual user survey. Your feedback is important because it allows us to judge the quality of our services, give DOE information on how we are doing, and point us to areas in which we can improve. The survey is on the web at the URL: https://www.nersc.gov/news-publications/publications-reports/user-surveys/2014/ and covers the allocation year 2014. Subscribe via RSS Subscribe

  7. Development Of 2-Meter Soil Temperature Probes And Results Of...

    Open Energy Info (EERE)

    obtains accurate temperatures within an hour of emplacing hollow steel probes into the ground, making it possible to map results on a daily basis so that temperature surveys can...

  8. behavioral-survey

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Evacuation Behavior Survey for No-Notice Emergency Scenarios" Presentation at the 93rd TRB Annual Meeting at the Traveler Behavior and Values Committee (ADB10) - Behavioral Process subcommittee; January 13, 2014 Joshua Auld, Vadim Sokolov, Rene Bautista, Angela Fontes Transportation Research and Analysis Computing Center Argonne National Laboratory Biography The presentation details a survey on evacuation response behavior that was conducted as a part of the RTSTEP project. The survey was

  9. tracc-evacuation-survey

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Survey Announcement SURVEY: The Transportation Research and Analysis computing center is conducting a survey to help with improvement of emergency evacuation planning in Chicago TRACC researchers under a contract with the City of Chicago are developing a model which predicts a response of a transportation network to an evacuation event. Emergency responders from OEMC and other local emergency management personal are to use the model results for "intuition training" purposes and

  10. Community Leaders Survey

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Community Leaders Survey Community Leaders Survey This survey is a tracking study commissioned by the Lab that helps measure perceived progress in maintaining community relationships and listening and responding to the needs of Northern New Mexico communities. Results help shape and direct the Lab's contributions to the region's future. Latest results show nine-in-ten of the community leaders express satisfaction with LANL's economic impact on the region. Study measures changes in leaders'

  11. 2004 User Survey Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    13 | Next 2004 User Survey Results Table of Contents Response Summary Respondent Demographics Overall Satisfaction and Importance All Satisfaction, Importance and Usefulness...

  12. 2006 User Survey Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to provide overall comments about NERSC: Here are the survey results: Respondent Demographics Overall Satisfaction and Importance All Satisfaction, Importance and Usefulness...

  13. 2005 User Survey Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    10 | Next 2005 User Survey Results Table of Contents Response Summary Respondent Demographics All Satisfaction, Importance and Usefulness Ratings Hardware Resources Software...

  14. 2003 User Survey Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    10 | Next 2003 User Survey Results Table of Contents Response Summary Respondent Demographics Overall Satisfaction and Importance All Satisfaction Topics and Changes from...

  15. Homeowner and Contractor Surveys

    Broader source: Energy.gov [DOE]

    Better Buildings Neighborhood Program Data and Evaluation Peer Exchange Call: Homeowner and Contractor Surveys, Call Slides and Discussion Summary, January 19, 2012.

  16. ORISE: Characterization surveys

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    objective characterization surveys to define the extent of radiological contamination at sites scheduled for decontamination and decommissioning (D&D). A fundamental...

  17. TPA Public Involvement Survey

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Hanford Tri-Party Agencies' Annual Public Involvement Survey Activities for Calendar Year 2008 Nolan Curtis Washington State Department of Ecology Nuclear Waste Program August 5,...

  18. 2011 NERSC User Survey (Read Only)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2010/2011 User Survey Results Survey Text 2009/2010 User Survey Results 2008/2009 User Survey Results 2007/2008 User Survey Results 2006 User Survey Results 2005 User Survey Results 2004 User Survey Results 2003 User Survey Results 2002 User Survey Results 2001 User Survey Results 2000 User Survey Results 1999 User Survey Results 1998 User Survey Results HPC Requirements for Science HPC Workshop Reports NERSC Staff Publications & Presentations Journal Cover Stories Galleries facebook icon

  19. In search of the dead zone: Use of otoliths for tracking fish exposure to hypoxia

    SciTech Connect (OSTI)

    Limburg, Karin E.; Walther, Benjamin D.; Lu, Zunli; Jackman, George; Mohan, John; Walther, Yvonne; Nissling, Anders; Weber, Peter K.; Schmitt, Axel K.

    2015-01-01

    Otolith chemistry is often useful for tracking provenance of fishes, as well as examining migration histories. Whereas elements such as strontium and barium correlate well with salinity and temperature, experiments that examine manganese uptake as a function of these parameters have found no such correlation. Instead, dissolved manganese is available as a redox product, and as such, is indicative of low-oxygen conditions. Here we present evidence for that mechanism in a range of habitats from marine to freshwater, across species, and also present ancillary proxies that support the mechanism as well. For example, iodine is redox-sensitive and varies inversely with Mn; and sulfur stable isotope ratios provide evidence of anoxic sulfate reduction in some circumstances.

  20. In search of the dead zone: Use of otoliths for tracking fish exposure to hypoxia

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Limburg, Karin E.; Walther, Benjamin D.; Lu, Zunli; Jackman, George; Mohan, John; Walther, Yvonne; Nissling, Anders; Weber, Peter K.; Schmitt, Axel K.

    2015-01-01

    Otolith chemistry is often useful for tracking provenance of fishes, as well as examining migration histories. Whereas elements such as strontium and barium correlate well with salinity and temperature, experiments that examine manganese uptake as a function of these parameters have found no such correlation. Instead, dissolved manganese is available as a redox product, and as such, is indicative of low-oxygen conditions. Here we present evidence for that mechanism in a range of habitats from marine to freshwater, across species, and also present ancillary proxies that support the mechanism as well. For example, iodine is redox-sensitive and varies inversely withmore » Mn; and sulfur stable isotope ratios provide evidence of anoxic sulfate reduction in some circumstances.« less

  1. Dark Energy Survey

    ScienceCinema (OSTI)

    Roodman, Aaron; Nord, Brian; Elliot, Ann

    2014-08-12

    Members of the Dark Energy Survey collaboration explain what they hope to learn by studying the southern sky with the world's most advanced digital camera, mounted on a telescope in Chile.

  2. 2000 User Survey Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    "NERSC has been the most stable supercomputer center in the country particularly with the migration from the T3E to the IBM SP". "Makes supercomputing easy." Below are the survey...

  3. Dark Energy Survey

    SciTech Connect (OSTI)

    Roodman, Aaron; Nord, Brian; Elliot, Ann

    2012-12-06

    Members of the Dark Energy Survey collaboration explain what they hope to learn by studying the southern sky with the world's most advanced digital camera, mounted on a telescope in Chile.

  4. Benchmarking survey for recycling.

    SciTech Connect (OSTI)

    Marley, Margie Charlotte; Mizner, Jack Harry

    2005-06-01

    This report describes the methodology, analysis and conclusions of a comparison survey of recycling programs at ten Department of Energy sites including Sandia National Laboratories/New Mexico (SNL/NM). The goal of the survey was to compare SNL/NM's recycling performance with that of other federal facilities, and to identify activities and programs that could be implemented at SNL/NM to improve recycling performance.

  5. Static Temperature Survey At Kilauea Summit Area (Keller, Et...

    Open Energy Info (EERE)

    L. Trowbridge Grose, John C. Murray, Catherine K. Skokan (1979) Results Of An Experimental Drill Hole At The Summit Of Kilauea Volcano, Hawaii Additional References Retrieved...

  6. Static Temperature Survey At Chena Area (Benoit, Et Al., 2007...

    Open Energy Info (EERE)

    Date Usefulness useful DOE-funding Unknown References Dick Benoit, Gwen Holdmann, David Blackwell (2007) Low Cost Exploration, Testing, And Development Of The Chena...

  7. Geology and Temperature Gradient Surveys Blue Mountain Geothermal...

    Open Energy Info (EERE)

    N50-60E,N50-60W, and N-S intersect in the geothermal zone providing deep permeability over a wide area. Extensive silicification andhydro brecciation accompanied...

  8. Static Temperature Survey At Lake City Hot Springs Area (Benoit...

    Open Energy Info (EERE)

    Notes Two deeper wells encountered temps of 327 and 329 oF References Dick Benoit, Joe Moore, Colin Goranson, David Blackwell (2005) Core Hole Drilling And Testing At The Lake...

  9. Static Temperature Survey (Cull, 1981) | Open Energy Information

    Open Energy Info (EERE)

    Date Usefulness useful DOE-funding Unknown Notes Although absolute values of heat flow may not be accurately determined with conventional techniques even at depths of 1000 m,...

  10. Static Temperature Survey At Molokai Area (Thomas, 1986) | Open...

    Open Energy Info (EERE)

    Activity Date Usefulness useful DOE-funding Unknown Notes Due to the very small potential market on the island of Molokai for geothermal energy, only a limited effort was made to...

  11. Static Temperature Survey At Lassen Volcanic National Park Area...

    Open Energy Info (EERE)

    indicate that the well has penetrated a lateral outflow plume of thermal water (Goff et al., 1988). References Cathy J. Janik, Marcia K. McLaren (2010) Seismicity And Fluid...

  12. Static Temperature Survey At Fort Bliss Area (Combs, Et Al.,...

    Open Energy Info (EERE)

    well. A suite of geophysical logs (gamma ray, neutron, sonic, and resistivity) was also run after completion of drilling. References Jim Combs, John T. Finger, Colin Goranson,...

  13. Two-Meter Temperature Surveys for Geothermal Exploration Project...

    Open Energy Info (EERE)

    years the Great Basin Center for Geothermal Energy has made progress toward developing methods and corrections aimed at eliminating these effects. Seasonal drift, albedo,...

  14. 2014 ALCF User Survey Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    survey, improved questions, and a representative user response to the survey. Demographics ALCF users are located around the world and are representative across different...

  15. NEPA Litigation Surveys | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    NEPA Litigation Surveys NEPA Litigation Surveys CEQ publishes surveys on NEPA litigation on an annual basis. These surveys identify the number of cases involving a NEPA based cause...

  16. Beamline Temperatures

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Temperatures Energy: 3.0000 GeV Current: 497.0950 mA Date: 16-May-2016 02:53:04 Beamline Temperatures Energy 3.0000 GeV Current 497.1 mA 16-May-2016 02:53:04 LN:MainTankLevel 168.9 in LN:MainTankPress 60.0 psi SPEAR-BL:B120HeFlow 13.4 l/min SPEAR-BL:B131HeFlow 22.7 l/min BL 2 BL02:M0_LCW 31.5 ℃ BL 4-1 BL04-1:BasePlate -13.0 ℃ BL04-1:Bottom1 54.0 ℃ BL04-1:Bottom2 55.0 ℃ BL04-1:Lower 32.0 ℃ BL04-1:Moly 64.0 ℃ BL04-1:ChinGuard1 31.0 ℃ BL04-1:ChinGuard2 31.0 ℃ BL04-1:FirstXtalA

  17. User Survey | Argonne Leadership Computing Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Survey User Survey Results The ALCF conducts yearly surveys to gain a better understanding of how we can improve the user experience at ALCF. Below are the numeric results of these surveys. 2014 ALCF User Survey Results 2013 ALCF User Survey Results 2012 ALCF User Survey Results 2011 ALCF User Survey Results 2010 ALCF User Survey Results 2009 ALCF User Survey Results 2008 ALCF User Survey Results

  18. 2001 FEMP Customer Survey Appendices

    SciTech Connect (OSTI)

    None

    2009-01-18

    Appendix A: Survey Instrument; Appendix B: Detailed Responses; Appendix C: Adoption and Diffusion of Innovations

  19. STEP Participant Survey Executive Summary

    Broader source: Energy.gov [DOE]

    STEP Participant Survey Executive Summary, from the Tool Kit Framework: Small Town University Energy Program (STEP).

  20. The 1986 residential occupant survey

    SciTech Connect (OSTI)

    Ivey, D.L.; Alley, P.K.

    1987-04-01

    In 1986, Pacific Northwest Laboratory developed the Residential Occupant Survey-Spring '86, which was implemented. The overall purpose of the study was to collect demographic, attitudinal, and behavioral data related to the use and conservation of electricity in dwellings participating in the Bonneville Power Administration's End-Use Load and Conservation Assessment Program (ELCAP). Information was collected on the respondents' perceptions of the energy efficiency of their dwelling, temperature the dwelling was kept when people were at home and awake during the last heating season, which rooms, if any, were not heated during the last heating season, number of times the dwelling was unoccupied for at least one week, number of times pets were let out of the dwelling per day, attitudes toward energy use and conservation and several socio-demographic variables such as age, sex, and total household income. The results of the data analyses showed age to be an important factor for reported indoor temperature and perceived energy efficiency of the dwelling. The results also showed that almost 60% of the ELCAP occupants do not heat one or more rooms during the heating season, and almost 45% of the ELCAP dwellings were unoccupied for at least one week during the reporting period. In terms of the reported allocation of household income for household energy expenses, the results showed that the reported dollar amount spent for the expenses remained relatively constant over income levels.

  1. Solar Site Survey Toolkit

    Broader source: Energy.gov [DOE]

    After a couple outings, a principal technologist at Sandia National Laboratories saw a need for a travel kit that would have the necessary tools to make the task of site surveys more manageable and safer. They have had great success using the kit in the field already.

  2. ARM User Survey Report

    SciTech Connect (OSTI)

    Roeder, LR

    2010-06-22

    The objective of this survey was to obtain user feedback to, among other things, determine how to organize the exponentially growing data within the Atmospheric Radiation Measurement (ARM) Climate Research Facility, and identify users’ preferred data analysis system. The survey findings appear to have met this objective, having received approximately 300 responses that give insight into the type of work users perform, usage of the data, percentage of data analysis users might perform on an ARM-hosted computing resource, downloading volume level where users begin having reservations, opinion about usage if given more powerful computing resources (including ability to manipulate data), types of tools that would be most beneficial to them, preferred programming language and data analysis system, level of importance for certain types of capabilities, and finally, level of interest in participating in a code-sharing community.

  3. Dead reckoning pedometer

    DOE Patents [OSTI]

    Eakle, Jr., Robert F.; Hofstetter, Kenneth J.

    2003-04-15

    A system to determine the location of a person within a structure utilizes a magnetometer, magnets, pressure sensors and a CPU to calculate the length and direction of each step. The data may be displayed to the wearer, preferably on a map or floorplan and may be broadcast to persons outside the structure.

  4. Sloan digital sky survey

    SciTech Connect (OSTI)

    Kent, S.M.; Stoughton, C.; Newberg, H.; Loveday, J.; Petravick, D.; Gurbani, V.; Berman, E.; Sergey, G.; Lupton, R.

    1994-04-01

    The Sloan Digital Sky Survey will produce a detailed digital photometric map of half the northern sky to about 23 magnitude using a special purpose wide field 2.5 meter telescope. From this map we will select {approximately} 10{sup 6} galaxies and 10{sup 5} quasars, and obtain high resolution spectra using the same telescope. The imaging catalog will contain 10{sup 8} galaxies, a similar number of stars, and 10{sup 6} quasar candidates.

  5. Use of Rapid Temperature Measurements at a 2-Meter Depth to Augment...

    Open Energy Info (EERE)

    obtains accurate temperatures within an hour of emplacing hollow steel probes into the ground, making it possible to map results on a daily basis so that temperature surveys can...

  6. Chinese Geological Survey | Open Energy Information

    Open Energy Info (EERE)

    Chinese Geological Survey Jump to: navigation, search Name: Chinese Geological Survey Place: China Sector: Geothermal energy Product: Chinese body which is involved in surveys of...

  7. Commercial Grade Dedication Survey and Training | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Survey and Training Commercial Grade Dedication Survey and Training The following is a sample plan to perform a CGD survey. The checklist items are included. In addition to,...

  8. Design Code Survey Form | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Design Code Survey Form Design Code Survey Form Survey of Safety Software Used in Design of Structures, Systems, and Components 1. Introduction The Department's Implementation Plan ...

  9. ORNL-5680 Radiological Surveys

    Office of Legacy Management (LM)

    DOVEV-0005/l (Supplement) ORNL-5680 Radiological Surveys of Properties in the Middlesex, New Jersey, Area R. W. Leggett D. L. Anderson F. F. Haywood D. J. Christian W. D. Cottrell R. W. Doane D. J. Crawford W. H. Shinpaugh E. B. Wagner T. E. Myrick W. A. Goldsmith Printed in the United States of America. Available from National Technical Information Service U.S. Department of Commerce 5285 Port Royal Road, Springfield, Virginia 22161 NTIS price codes-Printed Copy: A07 Microfiche ,401 I I This

  10. 2015 Uranium Marketing Annual Survey

    U.S. Energy Information Administration (EIA) Indexed Site

    U.S. Energy Information Administration, Form EIA-858 ""Uranium Marketing Annual Survey"" (2015)." " U.S. Energy Information Administration 2015 Uranium Marketing Annual Report 15

  11. Reflection Survey | Open Energy Information

    Open Energy Info (EERE)

    (Gritto, Et Al.) Rye Patch Area Integrated Seismic Studies At The Rye Patch Geothermal Reservoir, Nevada Reflection Survey At Rye Patch Area (Laney, 2005) Rye Patch Area Federal...

  12. Federal Buildings Supplemental Survey -- Overview

    U.S. Energy Information Administration (EIA) Indexed Site

    Buildings The Federal Buildings Supplemental Survey 1993 provides building-level energy-related characteristics for a special sample of commercial buildings owned by the...

  13. IRT Surveys | Open Energy Information

    Open Energy Info (EERE)

    consulting in building thermographers and thermal imaging allowing to detect energy loss and increase of energy efficiency. References: IRT Surveys1 This article is a stub....

  14. Idaho Geological Survey and University of Idaho Explore for Geothermal Energy

    Broader source: Energy.gov [DOE]

    The University of Idaho's Idaho Geological Survey recently drilled new wells in southeastern Idaho to provide the most accurate assessment of high-temperature geothermal energy potential in the region.

  15. DC Resistivity Survey (Mise-A-La-Masse) | Open Energy Information

    Open Energy Info (EERE)

    fluid type and phase state of the pore water Thermal: Resistivity influenced by temperature Dictionary.png DC Resistivity Survey (Mise-A-La-Masse): No definition has been...

  16. High Temperature ESP Monitoring

    Broader source: Energy.gov [DOE]

    The purpose of the High Temperature ESP Monitoring project is to develop a down-hole monitoring system to be used in wells with bottom hole temperature up to 300 °C for measuring motor temperature; pump discharge pressure; and formation temperature and pressure.

  17. Cooled, temperature controlled electrometer

    DOE Patents [OSTI]

    Morgan, John P.

    1992-08-04

    A cooled, temperature controlled electrometer for the measurement of small currents. The device employs a thermal transfer system to remove heat from the electrometer circuit and its environment and dissipate it to the external environment by means of a heat sink. The operation of the thermal transfer system is governed by a temperature regulation circuit which activates the thermal transfer system when the temperature of the electrometer circuit and its environment exceeds a level previously inputted to the external variable temperature control circuit. The variable temperature control circuit functions as subpart of the temperature control circuit. To provide temperature stability and uniformity, the electrometer circuit is enclosed by an insulated housing.

  18. Cooled, temperature controlled electrometer

    DOE Patents [OSTI]

    Morgan, John P.

    1992-01-01

    A cooled, temperature controlled electrometer for the measurement of small currents. The device employs a thermal transfer system to remove heat from the electrometer circuit and its environment and dissipate it to the external environment by means of a heat sink. The operation of the thermal transfer system is governed by a temperature regulation circuit which activates the thermal transfer system when the temperature of the electrometer circuit and its environment exceeds a level previously inputted to the external variable temperature control circuit. The variable temperature control circuit functions as subpart of the temperature control circuit. To provide temperature stability and uniformity, the electrometer circuit is enclosed by an insulated housing.

  19. High temperature furnace

    DOE Patents [OSTI]

    Borkowski, Casimer J.

    1976-08-03

    A high temperature furnace for use above 2000.degree.C is provided that features fast initial heating and low power consumption at the operating temperature. The cathode is initially heated by joule heating followed by electron emission heating at the operating temperature. The cathode is designed for routine large temperature excursions without being subjected to high thermal stresses. A further characteristic of the device is the elimination of any ceramic components from the high temperature zone of the furnace.

  20. Geodetic Survey | Open Energy Information

    Open Energy Info (EERE)

    At Kilauea Summit Area (Keller, Et Al., 1979) Kilauea Summit Area Results Of An Experimental Drill Hole At The Summit Of Kilauea Volcano, Hawaii Geodetic Survey At Long Valley...

  1. 2014 Manufacturing Energy Consumption Survey

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    U S C E N S U S B U R E A U 2014 Manufacturing Energy Consumption Survey Sponsored by the Energy Information Administration U.S. Department of Energy Administered and Compiled by ...

  2. 2005 Residential Energy Consumption Survey

    U.S. Energy Information Administration (EIA) Indexed Site

    Completed forms are due by March 4, 2006. If you have any questions, please call (toll-free) 1-NNN-NNN-NNNN. Ask for the Supplier Survey Specialist. This report is mandatory under ...

  3. 2005 Residential Energy Consumption Survey

    U.S. Energy Information Administration (EIA) Indexed Site

    Completed forms are due by March 4, 2006. If you have any questions, please call (toll-free) 1-NNN-NNN-NNNN. Ask for the Supplier Survey Specialist.. This report is mandatory under ...

  4. I COMPREHENSIVE RADIOLOGICAL SURVEY I

    Office of Legacy Management (LM)

    im I COMPREHENSIVE RADIOLOGICAL SURVEY I Prepared by Oak Ridge Associated Universities Prprd* OFF-SITE PROPERTY H' | Prepared for Office of Operational FORMER LAKE ONTARIO ORDNANCE WORKS SITE Safety U.S. Department LEWISTON, NEW YORK I of Energy i J.D. BERGER i Radiological Site Assessment Program Manpower Education, Research, and Training Division I l*~~~~~~ ~~~~DRAFT REPORT January 1983 I I I ------- COMPREHENSIVE RADIOLOGICAL SURVEY OFF-SITE PROPERTY H' FORMER LAKE ONTARIO ORDNANCE WORKS SITE

  5. Enzymatic temperature change indicator

    DOE Patents [OSTI]

    Klibanov, Alexander M.; Dordick, Jonathan S.

    1989-01-21

    A temperature change indicator is described which is composed of an enzyme and a substrate for that enzyme suspended in a solid organic solvent or mixture of solvents as a support medium. The organic solvent or solvents are chosen so as to melt at a specific temperature or in a specific temperature range. When the temperature of the indicator is elevated above the chosen, or critical temperature, the solid organic solvent support will melt, and the enzymatic reaction will occur, producing a visually detectable product which is stable to further temperature variation.

  6. Geophex Airborne Unmanned Survey System

    SciTech Connect (OSTI)

    Won, I.L.; Keiswetter, D.

    1995-12-31

    Ground-based surveys place personnel at risk due to the proximity of buried unexploded ordnance (UXO) items or by exposure to radioactive materials and hazardous chemicals. The purpose of this effort is to design, construct, and evaluate a portable, remotely-piloted, airborne, geophysical survey system. This non-intrusive system will provide stand-off capability to conduct surveys and detect buried objects, structures, and conditions of interest at hazardous locations. During a survey, the operators remain remote from, but within visual distance of, the site. The sensor system never contacts the Earth, but can be positioned near the ground so that weak geophysical anomalies can be detected. The Geophex Airborne Unmanned Survey System (GAUSS) is designed to detect and locate small-scale anomalies at hazardous sites using magnetic and electromagnetic survey techniques. The system consists of a remotely-piloted, radio-controlled, model helicopter (RCH) with flight computer, light-weight geophysical sensors, an electronic positioning system, a data telemetry system, and a computer base-station. The report describes GAUSS and its test results.

  7. 2008/2009 User Survey Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Next 20082009 User Survey Results Table of Contents Response Survey Respondent Demographics Overall Satisfaction and Importance All Satisfaction and Importance Ratings...

  8. Idaho Geological Survey | Open Energy Information

    Open Energy Info (EERE)

    The Idaho Geological Survey is located in Boise, Idaho. About Information on past oil and gas exploration wells in Idaho was transferred to the Idaho Geological Survey in...

  9. radiological. survey | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    survey NNSA to Conduct Aerial Radiological Surveys Over San Francisco, Pacifica, Berkeley, And Oakland, CA Areas A U.S. Department of Energy National Nuclear Security...

  10. FAQs for Survey Forms 804 and 814

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    intended for cracking into olefins. EIA-804 Survey form & instructions Contact: Robert Merriam, (202) 586-4615 EIA-814 Survey form & instructions Contact: Chris Buckner, (202)...

  11. Aftertreatment Research Prioritization: A CLEERS Industrial Survey...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Research Prioritization: A CLEERS Industrial Survey Aftertreatment Research Prioritization: A CLEERS Industrial Survey Presentation given at the 2007 Diesel Engine-Efficiency &...

  12. Category:Telluric Survey | Open Energy Information

    Open Energy Info (EERE)

    Pages in category "Telluric Survey" This category contains only the following page. T Telluric Survey Retrieved from "http:en.openei.orgwindex.php?titleCategory:Telluric...

  13. High temperature measuring device

    DOE Patents [OSTI]

    Tokarz, Richard D.

    1983-01-01

    A temperature measuring device for very high design temperatures (to 2,000.degree. C.). The device comprises a homogenous base structure preferably in the form of a sphere or cylinder. The base structure contains a large number of individual walled cells. The base structure has a decreasing coefficient of elasticity within the temperature range being monitored. A predetermined quantity of inert gas is confined within each cell. The cells are dimensionally stable at the normal working temperature of the device. Increases in gaseous pressure within the cells will permanently deform the cell walls at temperatures within the high temperature range to be measured. Such deformation can be correlated to temperature by calibrating similarly constructed devices under known time and temperature conditions.

  14. ARM - Measurement - Virtual temperature

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    would love to hear from you Send us a note below or call us at 1-888-ARM-DATA. Send Measurement : Virtual temperature The virtual temperature Tv T(1 + rvepsilon), where rv is...

  15. Temperature-profile detector

    DOE Patents [OSTI]

    Not Available

    1981-01-29

    Temperature profiles at elevated temperature conditions are monitored by use of an elongated device having two conductors spaced by the minimum distance required to normally maintain an open circuit between them. The melting point of one conductor is selected at the elevated temperature being detected, while the melting point of the other is higher. As the preselected temperature is reached, liquid metal will flow between the conductors creating short circuits which are detectable as to location.

  16. Temperature profile detector

    DOE Patents [OSTI]

    Tokarz, Richard D.

    1983-01-01

    Temperature profiles at elevated temperature conditions are monitored by use of an elongated device having two conductors spaced by the minimum distance required to normally maintain an open circuit between them. The melting point of one conductor is selected at the elevated temperature being detected, while the melting point of the other is higher. As the preselected temperature is reached, liquid metal will flow between the conductors, creating short circuits which are detectable as to location.

  17. High temperature sensor

    DOE Patents [OSTI]

    Tokarz, Richard D.

    1982-01-01

    A high temperature sensor includes a pair of electrical conductors separated by a mass of electrical insulating material. The insulating material has a measurable resistivity within the sensor that changes in relation to the temperature of the insulating material within a high temperature range (1,000 to 2,000 K.). When required, the sensor can be encased within a ceramic protective coating.

  18. Temperature compensated photovoltaic array

    DOE Patents [OSTI]

    Mosher, Dan Michael

    1997-11-18

    A temperature compensated photovoltaic module (20) comprised of a series of solar cells (22) having a thermally activated switch (24) connected in parallel with several of the cells (22). The photovoltaic module (20) is adapted to charge conventional batteries having a temperature coefficient (TC) differing from the temperature coefficient (TC) of the module (20). The calibration temperatures of the switches (24) are chosen whereby the colder the ambient temperature for the module (20), the more switches that are on and form a closed circuit to short the associated solar cells (22). By shorting some of the solar cells (22) as the ambient temperature decreases, the battery being charged by the module (20) is not excessively overcharged at lower temperatures. PV module (20) is an integrated solution that is reliable and inexpensive.

  19. Temperature compensated photovoltaic array

    DOE Patents [OSTI]

    Mosher, D.M.

    1997-11-18

    A temperature compensated photovoltaic module comprises a series of solar cells having a thermally activated switch connected in parallel with several of the cells. The photovoltaic module is adapted to charge conventional batteries having a temperature coefficient differing from the temperature coefficient of the module. The calibration temperatures of the switches are chosen whereby the colder the ambient temperature for the module, the more switches that are on and form a closed circuit to short the associated solar cells. By shorting some of the solar cells as the ambient temperature decreases, the battery being charged by the module is not excessively overcharged at lower temperatures. PV module is an integrated solution that is reliable and inexpensive. 2 figs.

  20. REMS Webinar Survey | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    REMS Webinar Survey REMS Webinar Survey Survey for the inaugural DOE REMS Webinar that was held on Tuesday, March 8, 2016 at 1:00 pm EST. PDF icon REMS Webinar Survey More Documents & Publications Radiation Exposure Monitoring Systems Data Submittal Notification EERE's Usability and Analysis Techniques Guidebook

  1. Sample Employee Survey for Workplace Charging Planning

    Broader source: Energy.gov [DOE]

    Survey to determine employee interest in the benefits of employer installed charging infrastructure for their PEVs.

  2. Residential Energy Consumption Survey: Quality Profile

    SciTech Connect (OSTI)

    1996-03-01

    The Residential Energy Consumption Survey (RECS) is a periodic national survey that provides timely information about energy consumption and expenditures of U.S. households and about energy-related characteristics of housing units. The survey was first conducted in 1978 as the National Interim Energy Consumption Survey (NIECS), and the 1979 survey was called the Household Screener Survey. From 1980 through 1982 RECS was conducted annually. The next RECS was fielded in 1984, and since then, the survey has been undertaken at 3-year intervals. The most recent RECS was conducted in 1993.

  3. Facility Approvals, Security Surveys, and Nuclear Materials Surveys

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1992-09-15

    To establish Department of Energy (DOE) requirements for granting facility approvals prior to permitting safeguards and security interests on the premises and the conduct of insite security and/or nuclear material surveys of facilities with safeguards and security interests. Cancels DOE 5634.1A. Canceled by DOE O 470.1 dated 9-28-95.

  4. Facility Approvals, Security Surveys, and Nuclear Materials Surveys

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1988-02-03

    To establish the Department of Energy (DOE) requirements for granting facility approvals prior to permitting safeguards and security interests on the premises and the conduct of on-site security and/or nuclear material surveys of facilities with safeguards and security interests. Cancels DOE O 5630.7 and DOE O 5634.1. Canceled by DOE 5634.1B.

  5. 2001 FEMP Customer Survey Appendices

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Appendices A Report Prepared for the US Department of Energy February 2002 By TecMRKT Works and Sandia National Laboratories TecMRKT Works Nicholas P. Hall John H. Reed Ph.D Thomas P. Talerico Jeff Riggert Andrew Oh And Sandia National Laboratories Gretchen Jordan FEMP Customer Survey Appendices Table of Contents Table of Contents TABLE OF CONTENTS I LIST OF FIGURES II LIST OF TABLES III APPENDIX A: SURVEY INSTRUMENT 1 APPENDIX B: DETAILED REPONSES 42 1. Participant and Nonparticipant Profiles

  6. NERSC-8 Vendor Market Survey

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NERSC-8 Project Lead NERSC-8 Market Survey --- 1 --- November 15, 2012 * Seek v endor i nput t o o p6mize 6 ming, r equirements and business prac6ces * Opportunity f or v endors t o p rovide i nput p rior t o formal p rocurement p rocess We are starting our next procurement, NERSC-8, with a round of market surveys Vendor B riefing --- 2 --- NERSC's mission is to enable science NERSC Mission: To accelerate the pace of scientific discovery by providing high-performance computing, data systems and

  7. Federal Employee Viewpoint Survey | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Policy and Guidance » Human Capital Management » Federal Employee Viewpoint Survey Federal Employee Viewpoint Survey The Federal Employee Viewpoint Survey (FedView survey) is a tool that measures employees' perceptions of whether, and to what extent, conditions characterizing successful organizations are present in their agencies. Survey results provide valuable insight into the challenges agency leaders face in ensuring the Federal Government has an effective civilian workforce and how well

  8. Deep Geothermal Reservoir Temperatures in the Eastern Snake River Plain,

    Office of Scientific and Technical Information (OSTI)

    Idaho using Multicomponent Geothermometry (Conference) | SciTech Connect Conference: Deep Geothermal Reservoir Temperatures in the Eastern Snake River Plain, Idaho using Multicomponent Geothermometry Citation Details In-Document Search Title: Deep Geothermal Reservoir Temperatures in the Eastern Snake River Plain, Idaho using Multicomponent Geothermometry The U.S. Geological survey has estimated that there are up to 4,900 MWe of undiscovered geothermal resources and 92,000 MWe of enhanced

  9. Magnetic nanoparticle temperature estimation

    SciTech Connect (OSTI)

    Weaver, John B.; Rauwerdink, Adam M.; Hansen, Eric W.

    2009-05-15

    The authors present a method of measuring the temperature of magnetic nanoparticles that can be adapted to provide in vivo temperature maps. Many of the minimally invasive therapies that promise to reduce health care costs and improve patient outcomes heat tissue to very specific temperatures to be effective. Measurements are required because physiological cooling, primarily blood flow, makes the temperature difficult to predict a priori. The ratio of the fifth and third harmonics of the magnetization generated by magnetic nanoparticles in a sinusoidal field is used to generate a calibration curve and to subsequently estimate the temperature. The calibration curve is obtained by varying the amplitude of the sinusoidal field. The temperature can then be estimated from any subsequent measurement of the ratio. The accuracy was 0.3 deg. K between 20 and 50 deg. C using the current apparatus and half-second measurements. The method is independent of nanoparticle concentration and nanoparticle size distribution.

  10. High-temperature sensor

    DOE Patents [OSTI]

    Not Available

    1981-01-29

    A high temperature sensor is described which includes a pair of electrical conductors separated by a mass of electrical insulating material. The insulating material has a measurable resistivity within the sensor that changes in relation to the temperature of the insulating material within a high temperature range (1000 to 2000/sup 0/K). When required, the sensor can be encased within a ceramic protective coating.

  11. High temperature refrigerator

    DOE Patents [OSTI]

    Steyert, Jr., William A.

    1978-01-01

    A high temperature magnetic refrigerator which uses a Stirling-like cycle in which rotating magnetic working material is heated in zero field and adiabatically magnetized, cooled in high field, then adiabatically demagnetized. During this cycle said working material is in heat exchange with a pumped fluid which absorbs heat from a low temperature heat source and deposits heat in a high temperature reservoir. The magnetic refrigeration cycle operates at an efficiency 70% of Carnot.

  12. Automatic temperature adjustment apparatus

    DOE Patents [OSTI]

    Chaplin, James E.

    1985-01-01

    An apparatus for increasing the efficiency of a conventional central space heating system is disclosed. The temperature of a fluid heating medium is adjusted based on a measurement of the external temperature, and a system parameter. The system parameter is periodically modified based on a closed loop process that monitors the operation of the heating system. This closed loop process provides a heating medium temperature value that is very near the optimum for energy efficiency.

  13. Temperature and RH Targets

    Broader source: Energy.gov [DOE]

    Presented by Vishal O Mittal of the Florida Solar Energy Center at the High Temperature Membrane Working Group Meeting, San Francisco, September 14, 2006.

  14. High-Temperature Materials

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Software Computations Uncertainty Quantification Stochastic About CRF Transportation Energy Consortiums Engine Combustion Heavy Duty Heavy Duty Low-Temperature & Diesel Combustion ...

  15. Low temperature cryoprobe

    DOE Patents [OSTI]

    Sungaila, Zenon F.

    1989-01-01

    A portable, hand held probe usable within a small confine to produce a point source of nitrogen or helium at a relatively constant temperature of 77 degrees Kelvin.

  16. Temperature and productivity

    Office of Scientific and Technical Information (OSTI)

    ... and performance of office work under combined exposure to temperature, noise and air pollution. PhD Thesis. International Centre for Indoor Environment and Energy, Department of ...

  17. Low Temperature Proton Conductivity

    Broader source: Energy.gov [DOE]

    Presentation by Tom Zawodzinski to DOE's Fuel Cell Operations at Sub-Freezing Temperatures Workshop held February 1-5, 2005 in Phoenix, Arizona.

  18. Hazards Survey and Hazards Assessments

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1997-08-21

    This volume is to assist DOE Operations/Field Offices and operating contractors in complying with the DOE O 151.1 requirement that Hazards Surveys and facility-specific Hazards Assessments be prepared, maintained, and used for emergency planning purposes. Canceled by DOE G 151.1-2.

  19. ARM - Word Seek: Temperature

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Temperature Outreach Home Room News Publications Traditional Knowledge Kiosks Barrow, Alaska Tropical Western Pacific Site Tours Contacts Students Study Hall About ARM Global Warming FAQ Just for Fun Meet our Friends Cool Sites Teachers Teachers' Toolbox Lesson Plans Word Seek: Temperature

  20. Fiber optic temperature sensor

    SciTech Connect (OSTI)

    Rabold, D.

    1995-12-01

    Our fiber optic temperature measurement sensor and system is a major improvement over methods currently in use in most industrial processes, and it delivers all of the attributes required simplicity, accuracy, and cost efficiency-to help improve all of these processes. Because temperature is a basic physical attribute of nearly every industrial and commercial process, our system can eventually result in significant improvements in nearly every industrial and commercial process. Many finished goods, and the materials that go into them, are critically dependent on the temperature. The better the temperature measurement, the better quality the goods will be and the more economically they can be produced. The production and transmission of energy requires the monitoring of temperature in motors, circuit breakers, power generating plants, and transmission line equipment. The more reliable and robust the methods for measuring these temperature, the more available, stable, and affordable the supply of energy will become. The world is increasingly realizing the threats to health and safety of toxic or otherwise undesirable by products of the industrial economy in the environment. Cleanup of such contamination often depends on techniques that require the constant monitoring of temperature in extremely hazardous environments, which can damage most conventional temperature sensors and which are dangerous for operating personnel. Our system makes such monitoring safer and more economical.

  1. High Temperature ESP Monitoring

    SciTech Connect (OSTI)

    Jack Booker; Brindesh Dhruva

    2011-06-20

    The objective of the High Temperature ESP Monitoring project was to develop a downhole monitoring system to be used in wells with bottom hole well temperatures up to 300C for measuring motor temperature, formation pressure, and formation temperature. These measurements are used to monitor the health of the ESP motor, to track the downhole operating conditions, and to optimize the pump operation. A 220 C based High Temperature ESP Monitoring system was commercially released for sale with Schlumberger ESP motors April of 2011 and a 250 C system with will be commercially released at the end of Q2 2011. The measurement system is now fully qualified, except for the sensor, at 300 C.

  2. High temperature probe

    DOE Patents [OSTI]

    Swan, Raymond A.

    1994-01-01

    A high temperature probe for sampling, for example, smokestack fumes, and is able to withstand temperatures of 3000.degree. F. The probe is constructed so as to prevent leakage via the seal by placing the seal inside the water jacket whereby the seal is not exposed to high temperature, which destroys the seal. The sample inlet of the probe is also provided with cooling fins about the area of the seal to provide additional cooling to prevent the seal from being destroyed. Also, a heated jacket is provided for maintaining the temperature of the gas being tested as it passes through the probe. The probe includes pressure sensing means for determining the flow velocity of an efficient being sampled. In addition, thermocouples are located in various places on the probe to monitor the temperature of the gas passing there through.

  3. Rural electric cooperatives IRP survey

    SciTech Connect (OSTI)

    Garrick, C.

    1995-11-01

    This report summarizes the integrated resource planning (IRP) practices of US rural electric cooperatives and the IRP policies which influence these practices. It was prepared by the National Renewable Energy Laboratory (NREL) and its subcontractor Garrick and Associates to assist the US Department of Energy (DOE) in satisfying the reporting requirements of Title 1, Subtitle B, Section 111(e)(3) of the Energy Policy Act of 1992 (EPAct), which states: (e) Report--Not later than 2 years after the date of the enactment of this Act, the Secretary (of the US Department of Energy) shall transmit a report to the President and to the Congress containing--(the findings from several surveys and evaluations, including:); (3) a survey of practices and policies under which electric cooperatives prepare IRPs, submit such plans to REA, and the extent to which such integrated resource planning is reflected in rates charged to customers.

  4. PRELIMINARY SURVEY OF VITRO CORPORATION

    Office of Legacy Management (LM)

    PRELIMINARY SURVEY OF VITRO CORPORATION (VITRO LABORATORIES) WEST ORANGE, NEW JERSEY Work performed by the Health and Safety Research Division Oak Ridge National Laboratory Oak Ridge, Tennessee 37830 March 1980 OAK RIDGE NATIONAL LABORATORY operated by UNION CARBIDE CORPORATION for the DEPARTMENT OF ENERGY as part of the Formerly Utilized Sites-- Remedial Actton Program VITRO CORPORATION (VITRO LABORATORIES) WEST ORANGE, NEW JERSEY At the request of the Department of Energy (DOE), a preliminary

  5. Temperature-sensitive optrode

    DOE Patents [OSTI]

    Hirschfeld, Tomas B.

    1985-01-01

    Method and apparatus are provided for measuring temperature and for generating optical signals related to temperature. Light from a fiber optic is directed to a material whose fluorescent response varies with ambient temperature. The same fiber optic delivering the excitation beam also collects a portion of the fluorescent emission for analysis. Signal collection efficiency of the fiber optic is enhanced by requiring that the fluorescent probe material be in the shape of an oblong parabolically tapered solid. Reproducibility is enhanced by using Raman backscatter to monitor excitation beam fluctuations, and by using measurements of fluorescence lifetime.

  6. Temperature-sensitive optrode

    DOE Patents [OSTI]

    Hirschfeld, T.B.

    1985-09-24

    Method and apparatus are provided for measuring temperature and for generating optical signals related to temperature. Light from a fiber optic is directed to a material whose fluorescent response varies with ambient temperature. The same fiber optic delivering the excitation beam also collects a portion of the fluorescent emission for analysis. Signal collection efficiency of the fiber optic is enhanced by requiring that the fluorescent probe material be in the shape of an oblong parabolically tapered solid. Reproducibility is enhanced by using Raman backscatter to monitor excitation beam fluctuations, and by using measurements of fluorescence lifetime. 10 figs.

  7. "Speak Up" Survey Results - Hanford Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    in the survey. The goal is to use the results to continuously improve Hanford's safety culture and work environment. Results for the "Speak Up" Survey An Organizational Climate and...

  8. Utah Geological Survey | Open Energy Information

    Open Energy Info (EERE)

    Logo: Utah Geological Survey Name: Utah Geological Survey Address: 1594 W. North Temple Place: Salt Lake City, Utah Zip: 84114-6100 Phone Number: 801.537.3300 Website:...

  9. STEP Non-Participant Survey Report

    Broader source: Energy.gov [DOE]

    STEP Non-Participant Survey Report, from the Tool Kit Framework: Small Town University Energy Program (STEP).

  10. DC Survey 2013 | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Management / Aerial Measuring System DC Survey 2013 DC Background Survey (.zip) DC 2013 survey Related Topics ams Emergency Response Related News Department of Energy's chief risk officer visits Nevada National Security Site NNSA sites prepared for disasters using real-time response management system NNSA emergency response assets highlighted NNSA displays helicopter in Baltimore NNSA to Conduct Aerial Radiation Monitoring Survey over Boston April 17-20

  11. 2005 Residential Energy Consumption Survey

    U.S. Energy Information Administration (EIA) Indexed Site

    ... foot at a pressure base of 14.73 pounds standard per square inch absolute and a temperature base of 60 degrees Fahrenheit; Cubic meter is a unit of measure which equals 35.314 ...

  12. Temperature | Open Energy Information

    Open Energy Info (EERE)

    C Property:Combustion Intake Air Temperature F Property:FirstWellTemp G Property:GeochemReservoirTemp Property:GeofluidTemp M Property:MeanReservoirTemp R...

  13. Penrose Well Temperatures

    SciTech Connect (OSTI)

    Christopherson, Karen

    2013-03-15

    Penrose Well Temperatures Geothermal waters have been encountered in several wells near Penrose in Fremont County, Colorado. Most of the wells were drilled for oil and gas exploration and, in a few cases, production. This ESRI point shapefile utilizes data from 95 wells in and around the Penrose area provided by the Colorado Oil and Gas Conservation Commission (COGCC) database at http://cogcc.state.co.us/ . Temperature data from the database were used to calculate a temperature gradient for each well. This information was then used to estimate temperatures at various depths. Projection: UTM Zone 13 NAD27 Extent: West -105.224871 East -105.027633 North 38.486269 South 38.259507 Originators: Colorado Oil and Gas Conservation Commission (COGCC) Karen Christopherson

  14. Low temperature cryoprobe

    DOE Patents [OSTI]

    Sungaila, Z.F.

    1988-04-12

    A portable, hand held probe usable within a small confine to produce a point source of nitrogen or helium at a relatively constant temperatures of 77 degrees Kelvin, is discussed. 3 figs.

  15. High-Temperature Superconductivity

    ScienceCinema (OSTI)

    Peter Johnson

    2010-01-08

    Like astronomers tweaking images to gain a more detailed glimpse of distant stars, physicists at Brookhaven National Laboratory have found ways to sharpen images of the energy spectra in high-temperature superconductors ? materials that carry electrical c

  16. High temperature pressure gauge

    DOE Patents [OSTI]

    Echtler, J. Paul (Pittsburgh, PA); Scandrol, Roy O. (Library, PA)

    1981-01-01

    A high temperature pressure gauge comprising a pressure gauge positioned in fluid communication with one end of a conduit which has a diaphragm mounted in its other end. The conduit is filled with a low melting metal alloy above the diaphragm for a portion of its length with a high temperature fluid being positioned in the remaining length of the conduit and in the pressure gauge.

  17. Low temperature reactive bonding

    DOE Patents [OSTI]

    Makowiecki, Daniel M. (Livermore, CA); Bionta, Richard M. (Livermore, CA)

    1995-01-01

    The joining technique requires no external heat source and generates very little heat during joining. It involves the reaction of thin multilayered films deposited on faying surfaces to create a stable compound that functions as an intermediate or braze material in order to create a high strength bond. While high temperatures are reached in the reaction of the multilayer film, very little heat is generated because the films are very thin. It is essentially a room temperature joining process.

  18. Temperature measuring device

    DOE Patents [OSTI]

    Lauf, Robert J.; Bible, Don W.; Sohns, Carl W.

    1999-01-01

    Systems and methods are described for a wireless instrumented silicon wafer that can measure temperatures at various points and transmit those temperature readings to an external receiver. The device has particular utility in the processing of semiconductor wafers, where it can be used to map thermal uniformity on hot plates, cold plates, spin bowl chucks, etc. without the inconvenience of wires or the inevitable thermal perturbations attendant with them.

  19. High Temperature Aqueous Chemistry

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Accurate knowledge of aqueous chemistry at high temperatures and pressures is important in many applications including nuclear waste disposal and energy extraction. Sandia's Defense Waste Management Programs is equipped with a state-of-the-art hydrothermal experimental system that allows us to obtain high quality kinetic and equilibrium data at temperatures and pressures of interest up to 600 o C and 1,000 bars (100 MPa). This state-of-the-art hydrothermal experimental system includes the

  20. ARM - Temperature Converter

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CalculatorsTemperature Converter Outreach Home Room News Publications Traditional Knowledge Kiosks Barrow, Alaska Tropical Western Pacific Site Tours Contacts Students Study Hall About ARM Global Warming FAQ Just for Fun Meet our Friends Cool Sites Teachers Teachers' Toolbox Lesson Plans Temperature Converter The Fahrenheit scale, invented by German physicist Daniel Gabriel Fahrenheit (1686-1736), is based on 32 °F for the freezing point of water and 212 °F for the boiling point of water. The

  1. Crystal structure, mutational analysis and RNA-dependent ATPase activity of the yeast DEAD-box pre-mRNA splicing factor Prp28

    SciTech Connect (OSTI)

    Jacewicz, Agata; Schwer, Beate; Smith, Paul; Shuman, Stewart

    2014-10-10

    Yeast Prp28 is a DEAD-box pre-mRNA splicing factor implicated in displacing U1 snRNP from the 5' splice site. Here we report that the 588-aa Prp28 protein consists of a trypsin-sensitive 126-aa N-terminal segment (of which aa 189 are dispensable for Prp28 function in vivo) fused to a trypsin-resistant C-terminal catalytic domain. Purified recombinant Prp28 and Prp28-(127588) have an intrinsic RNA-dependent ATPase activity, albeit with a low turnover number. The crystal structure of Prp28-(127588) comprises two RecA-like domains splayed widely apart. AMPPNPMg2+ is engaged by the proximal domain, with proper and specific contacts from Phe194 and Gln201 (Q motif) to the adenine nucleobase. The triphosphate moiety of AMPPNPMg2+ is not poised for catalysis in the open domain conformation. Guided by the Prp28AMPPNP structure, and that of the Drosophila VasaAMPPNPMg2+RNA complex, we targeted 20 positions in Prp28 for alanine scanning. ATP-site components Asp341 and Glu342 (motif II) and Arg527 and Arg530 (motif VI) and RNA-site constituent Arg476 (motif Va) are essential for Prp28 activity in vivo. Synthetic lethality of double-alanine mutations highlighted functionally redundant contacts in the ATP-binding (Phe194-Gln201, Gln201-Asp502) and RNA-binding (Arg264-Arg320) sites. As a result, overexpression of defective ATP-site mutants, but not defective RNA-site mutants, elicited severe dominant-negative growth defects.

  2. Crystal structure, mutational analysis and RNA-dependent ATPase activity of the yeast DEAD-box pre-mRNA splicing factor Prp28

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Jacewicz, Agata; Schwer, Beate; Smith, Paul; Shuman, Stewart

    2014-10-10

    Yeast Prp28 is a DEAD-box pre-mRNA splicing factor implicated in displacing U1 snRNP from the 5' splice site. Here we report that the 588-aa Prp28 protein consists of a trypsin-sensitive 126-aa N-terminal segment (of which aa 1–89 are dispensable for Prp28 function in vivo) fused to a trypsin-resistant C-terminal catalytic domain. Purified recombinant Prp28 and Prp28-(127–588) have an intrinsic RNA-dependent ATPase activity, albeit with a low turnover number. The crystal structure of Prp28-(127–588) comprises two RecA-like domains splayed widely apart. AMPPNP•Mg2+ is engaged by the proximal domain, with proper and specific contacts from Phe194 and Gln201 (Q motif) to themore » adenine nucleobase. The triphosphate moiety of AMPPNP•Mg2+ is not poised for catalysis in the open domain conformation. Guided by the Prp28•AMPPNP structure, and that of the Drosophila Vasa•AMPPNP•Mg2+•RNA complex, we targeted 20 positions in Prp28 for alanine scanning. ATP-site components Asp341 and Glu342 (motif II) and Arg527 and Arg530 (motif VI) and RNA-site constituent Arg476 (motif Va) are essential for Prp28 activity in vivo. Synthetic lethality of double-alanine mutations highlighted functionally redundant contacts in the ATP-binding (Phe194-Gln201, Gln201-Asp502) and RNA-binding (Arg264-Arg320) sites. As a result, overexpression of defective ATP-site mutants, but not defective RNA-site mutants, elicited severe dominant-negative growth defects.« less

  3. Survey of the Economics of Hydrogen Technologies | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Survey of the Economics of Hydrogen Technologies Survey of the Economics of Hydrogen Technologies Survey of the Economics of Hydrogen Technologies PDF icon 27079.pdf More Documents ...

  4. Gamma Survey of a Permeable Reactive Barrier at Monticello, Utah...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Gamma Survey of a Permeable Reactive Barrier at Monticello, Utah Gamma Survey of a Permeable Reactive Barrier at Monticello, Utah Gamma Survey of a Permeable Reactive Barrier at...

  5. Department of Energy Earned Value Management Survey Results ...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Earned Value Management Survey Results Department of Energy Earned Value Management Survey Results Humphreys & Associates, Inc. (H&A) conducted a survey of ...

  6. Housing characteristics, 1987: Residential Energy Consumption Survey

    SciTech Connect (OSTI)

    Not Available

    1989-05-26

    This report is the first of a series of reports based on data from the 1987 RECS. The 1987 RECS is the seventh in the series of national surveys of households and their energy suppliers. These surveys provide baseline information on how households in the United States use energy. A cross section of housing types such as single-family detached homes, townhouses, large and small apartment buildings, condominiums, and mobile homes were included in the survey. Data from the RECS and a companion survey, the Residential Transportation Energy Consumption Survey (RTECS), are available to the public in published reports such as this one and on public use tapes. 10 figs., 69 tabs.

  7. Helicopter magnetic survey conducted to locate wells

    SciTech Connect (OSTI)

    Veloski, G.A.; Hammack, R.W.; Stamp, V.; Hall, R.; Colina, K.

    2008-07-01

    A helicopter magnetic survey was conducted in August 2007 over 15.6 sq mi at the Naval Petroleum Reserve No. 3s (NPR-3) Teapot Dome Field near Casper, Wyoming. The surveys purpose was to accurately locate wells drilled there during more than 90 years of continuous oilfield operation. The survey was conducted at low altitude and with closely spaced flight lines to improve the detection of wells with weak magnetic response and to increase the resolution of closely spaced wells. The survey was in preparation for a planned CO2 flood for EOR, which requires a complete well inventory with accurate locations for all existing wells. The magnetic survey was intended to locate wells missing from the well database and to provide accurate locations for all wells. The ability of the helicopter magnetic survey to accurately locate wells was accomplished by comparing airborne well picks with well locations from an intense ground search of a small test area.

  8. Site survey method and apparatus

    DOE Patents [OSTI]

    Oldham, James G.; Spencer, Charles R.; Begley, Carl L.; Meyer, H. Robert

    1991-06-18

    The disclosure of the invention is directed to a site survey ground vehicle based apparatus and method for automatically detecting source materials, such as radioactivity, marking the location of the source materials, such as with paint, and mapping the location of the source materials on a site. The apparatus of the invention is also useful for collecting and analyzing samples. The apparatus includes a ground vehicle, detectors mounted at the front of the ground vehicle, and individual detector supports which follow somewhat irregular terrain to allow consistent and accurate detection, and autolocation equipment.

  9. Site survey method and apparatus

    DOE Patents [OSTI]

    Oldham, J.G.; Spencer, C.R.; Begley, C.L.; Meyer, H.R.

    1991-06-18

    The disclosure of the invention is directed to a site survey ground vehicle based apparatus and method for automatically detecting source materials, such as radioactivity, marking the location of the source materials, such as with paint, and mapping the location of the source materials on a site. The apparatus of the invention is also useful for collecting and analyzing samples. The apparatus includes a ground vehicle, detectors mounted at the front of the ground vehicle, and individual detector supports which follow somewhat irregular terrain to allow consistent and accurate detection, and autolocation equipment. 19 figures.

  10. High temperature thermometric phosphors

    DOE Patents [OSTI]

    Allison, S.W.; Cates, M.R.; Boatner, L.A.; Gillies, G.T.

    1999-03-23

    A high temperature phosphor consists essentially of a material having the general formula LuPO{sub 4}:Dy{sub x},Eu{sub y} wherein: 0.1 wt % {<=} x {<=} 20 wt % and 0.1 wt % {<=} y {<=} 20 wt %. The high temperature phosphor is in contact with an article whose temperature is to be determined. The article having the phosphor in contact with it is placed in the environment for which the temperature of the article is to be determined. The phosphor is excited by a laser causing the phosphor to fluoresce. The emission from the phosphor is optically focused into a beam-splitting mirror which separates the emission into two separate emissions, the emission caused by the dysprosium dopant and the emission caused by the europium dopant. The separated emissions are optically filtered and the intensities of the emission are detected and measured. The ratio of the intensity of each emission is determined and the temperature of the article is calculated from the ratio of the intensities of the separate emissions. 2 figs.

  11. High temperature thermometric phosphors

    DOE Patents [OSTI]

    Allison, Stephen W.; Cates, Michael R.; Boatner, Lynn A.; Gillies, George T.

    1999-03-23

    A high temperature phosphor consists essentially of a material having the general formula LuPO.sub.4 :Dy.sub.(x),Eu.sub.y) wherein: 0.1 wt %.ltoreq.x.ltoreq.20 wt % and 0.1 wt %.ltoreq.y.ltoreq.20 wt %. The high temperature phosphor is in contact with an article whose temperature is to be determined. The article having the phosphor in contact with it is placed in the environment for which the temperature of the article is to be determined. The phosphor is excited by a laser causing the phosphor to fluoresce. The emission from the phosphor is optically focused into a beam-splitting mirror which separates the emission into two separate emissions, the emission caused by the dysprosium dopant and the emission caused by the europium dopent. The separated emissions are optically filtered and the intensities of the emission are detected and measured. The ratio of the intensity of each emission is determined and the temperature of the article is calculated from the ratio of the intensities of the separate emissions.

  12. Temperature profile detector

    DOE Patents [OSTI]

    Tokarz, R.D.

    1983-10-11

    Disclosed is a temperature profile detector shown as a tubular enclosure surrounding an elongated electrical conductor having a plurality of meltable conductive segments surrounding it. Duplicative meltable segments are spaced apart from one another along the length of the enclosure. Electrical insulators surround these elements to confine molten material from the segments in bridging contact between the conductor and a second electrical conductor, which might be the confining tube. The location and rate of growth of the resulting short circuits between the two conductors can be monitored by measuring changes in electrical resistance between terminals at both ends of the two conductors. Additional conductors and separate sets of meltable segments operational at differing temperatures can be monitored simultaneously for measuring different temperature profiles. 8 figs.

  13. High temperature lubricating process

    DOE Patents [OSTI]

    Taylor, R.W.; Shell, T.E.

    1979-10-04

    It has been difficult to provide adequate lubrication for load bearing, engine components when such engines are operating in excess of about 475/sup 0/C. The present invention is a process for providing a solid lubricant on a load bearing, solid surface, such as in an engine being operated at temperatures in excess of about 475/sup 0/C. The process comprises contacting and maintaining the following steps: a gas phase is provided which includes at least one component reactable in a temperature dependent reaction to form a solid lubricant; the gas phase is contacted with the load bearing surface; the load bearing surface is maintained at a temperature which causes reaction of the gas phase component and the formation of the solid lubricant; and the solid lubricant is formed directly on the load bearing surface. The method is particularly suitable for use with ceramic engines.

  14. High temperature lubricating process

    DOE Patents [OSTI]

    Taylor, Robert W.; Shell, Thomas E.

    1982-01-01

    It has been difficult to provide adaquate lubrication for load bearing, engine components when such engines are operating in excess of about 475.degree. C. The present invention is a process for providing a solid lubricant on a load bearing, solid surface (14), such as in an engine (10) being operated at temperatures in excess of about 475.degree. C. The process comprises contacting and maintaining steps. A gas phase (42) is provided which includes at least one component reactable in a temperature dependent reaction to form a solid lubricant. The gas phase is contacted with the load bearing surface. The load bearing surface is maintained at a temperature which causes reaction of the gas phase component and the formation of the solid lubricant. The solid lubricant is formed directly on the load bearing surface. The method is particularly suitable for use with ceramic engines.

  15. Temperature initiated passive cooling system

    DOE Patents [OSTI]

    Forsberg, Charles W.

    1994-01-01

    A passive cooling system for cooling an enclosure only when the enclosure temperature exceeds a maximum standby temperature comprises a passive heat transfer loop containing heat transfer fluid having a particular thermodynamic critical point temperature just above the maximum standby temperature. An upper portion of the heat transfer loop is insulated to prevent two phase operation below the maximum standby temperature.

  16. Temperature initiated passive cooling system

    DOE Patents [OSTI]

    Forsberg, C.W.

    1994-11-01

    A passive cooling system for cooling an enclosure only when the enclosure temperature exceeds a maximum standby temperature comprises a passive heat transfer loop containing heat transfer fluid having a particular thermodynamic critical point temperature just above the maximum standby temperature. An upper portion of the heat transfer loop is insulated to prevent two phase operation below the maximum standby temperature. 1 fig.

  17. Reservoir Temperature Estimator

    Energy Science and Technology Software Center (OSTI)

    2014-12-08

    The Reservoir Temperature Estimator (RTEst) is a program that can be used to estimate deep geothermal reservoir temperature and chemical parameters such as CO2 fugacity based on the water chemistry of shallower, cooler reservoir fluids. This code uses the plugin features provided in The Geochemist’s Workbench (Bethke and Yeakel, 2011) and interfaces with the model-independent parameter estimation code Pest (Doherty, 2005) to provide for optimization of the estimated parameters based on the minimization of themore » weighted sum of squares of a set of saturation indexes from a user-provided mineral assemblage.« less

  18. Fluorescent temperature sensor

    DOE Patents [OSTI]

    Baker, Gary A [Los Alamos, NM; Baker, Sheila N [Los Alamos, NM; McCleskey, T Mark [Los Alamos, NM

    2009-03-03

    The present invention is a fluorescent temperature sensor or optical thermometer. The sensor includes a solution of 1,3-bis(1-pyrenyl)propane within a 1-butyl-1-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide ionic liquid solvent. The 1,3-bis(1-pyrenyl)propane remains unassociated when in the ground state while in solution. When subjected to UV light, an excited state is produced that exists in equilibrium with an excimer. The position of the equilibrium between the two excited states is temperature dependent.

  19. Temperature determination using pyrometry

    DOE Patents [OSTI]

    Breiland, William G.; Gurary, Alexander I.; Boguslavskiy, Vadim

    2002-01-01

    A method for determining the temperature of a surface upon which a coating is grown using optical pyrometry by correcting Kirchhoff's law for errors in the emissivity or reflectance measurements associated with the growth of the coating and subsequent changes in the surface thermal emission and heat transfer characteristics. By a calibration process that can be carried out in situ in the chamber where the coating process occurs, an error calibration parameter can be determined that allows more precise determination of the temperature of the surface using optical pyrometry systems. The calibration process needs only to be carried out when the physical characteristics of the coating chamber change.

  20. Low temperature reactive bonding

    DOE Patents [OSTI]

    Makowiecki, D.M.; Bionta, R.M.

    1995-01-17

    The joining technique is disclosed that requires no external heat source and generates very little heat during joining. It involves the reaction of thin multilayered films deposited on faying surfaces to create a stable compound that functions as an intermediate or braze material in order to create a high strength bond. While high temperatures are reached in the reaction of the multilayer film, very little heat is generated because the films are very thin. It is essentially a room temperature joining process. 5 figures.

  1. Wellbore inertial directional surveying system

    DOE Patents [OSTI]

    Andreas, Ronald D.; Heck, G. Michael; Kohler, Stewart M.; Watts, Alfred C.

    1991-01-01

    A wellbore inertial directional surveying system for providing a complete directional survey of an oil or gas well borehole to determine the displacement in all three directions of the borehole path relative to the well head at the surface. The information generated by the present invention is especially useful when numerous wells are drilled to different geographical targets from a single off-shore platform. Accurate knowledge of the path of the borehole allows proper well spacing and provides assurance that target formations are reached. The tool is lowered down into a borehole on the electrical cable. A computer positioned on the surface communicates with the tool via the cable. The tool contains a sensor block which is supported on a single gimbal, the rotation axis of which is aligned with the cylinder axis of the tool and, correspondingly, the borehole. The gyroscope measurement of the sensor block rotation is used in a null-seeking servo loop which essentially prevents rotation of the sensor block aboutthe gimbal axis. Angular rates of the sensor block about axes which are perpendicular to the gimbal axis are measured by gyroscopes in a manner similar to a strapped-down arrangement. Three accelerometers provide acceleration information as the tool is lowered within the borehole. The uphole computer derives position information based upon acceleration information and anular rate information. Kalman estimation techniques are used to compensate for system errors.

  2. Wellbore inertial directional surveying system

    DOE Patents [OSTI]

    Andreas, R.D.; Heck, G.M.; Kohler, S.M.; Watts, A.C.

    1982-09-08

    A wellbore inertial directional surveying system for providing a complete directional survey of an oil or gas well borehole to determine the displacement in all three directions of the borehole path relative to the well head at the surface. The information generated by the present invention is especially useful when numerous wells are drilled to different geographical targets from a single offshore platform. Accurate knowledge of the path of the borehole allows proper well spacing and provides assurance that target formations are reached. The tool is lowered down into a borehole on an electrical cable. A computer positioned on the surface communicates with the tool via the cable. The tool contains a sensor block which is supported on a single gimbal, the rotation axis of which is aligned with the cylinder axis of the tool and, correspondingly, the borehole. The gyroscope measurement of the sensor block rotation is used in a null-seeking servo loop which essentially prevents rotation of the sensor block about the gimbal axis. Angular rates of the sensor block about axes which are perpendicular to te gimbal axis are measured by gyroscopes in a manner similar to a strapped-down arrangement. Three accelerometers provide acceleration information as the tool is lowered within the borehole. The uphole computer derives position information based upon acceleration information and angular rate information. Kalman estimation techniques are used to compensate for system errors. 25 figures.

  3. 1992--1993 low-temperature geothermal assessment program, Colorada

    SciTech Connect (OSTI)

    Cappa, J.A.; Hemborg, H.T.

    1995-01-01

    Previous assessments of Colorado`s low-temperature geothermal resources were completed by the Colorado Geological Survey in 1920 and in the mid- to late-1970s. The purpose of the 1992--1993 low-temperature geothermal resource assessment is to update the earlier physical, geochemical, and utilization data and compile computerized databases of the location, chemistry, and general information of the low-temperature geothermal resources in Colorado. The main sources of the data included published data from the Colorado Geological Survey, the US Geological Survey WATSTOR database, and the files of the State Division of Water Resources. The staff of the Colorado Geological Survey in 1992 and 1993 visited most of the known geothermal sources that were recorded as having temperatures greater than 30{degrees}C. Physical measurements of the conductivity, pH, temperature, flow rate, and notes on the current geothermal source utilization were taken. Ten new geochemical analyses were completed on selected geothermal sites. The results of the compilation and field investigations are compiled into the four enclosed Quattro Pro 4 databases. For the purposes of this report a geothermal area is defined as a broad area, usually less than 3 sq mi in size, that may have several wells or springs. A geothermal site is an individual well or spring within a geothermal area. The 1992-1993 assessment reports that there are 93 geothermal areas in the Colorado, up from the 56 reported in 1978; there are 157 geothermal sites up from the 125 reported in 1978; and a total of 382 geochemical analyses are compiled, up from the 236 reported in 1978. Six geothermal areas are recommended for further investigation: Trimble Hot Springs, Orvis Hot Springs, an area southeast of Pagosa Springs, the eastern San Luis Valley, Rico and Dunton area, and Cottonwood Hot Springs.

  4. Temperature differential detection device

    DOE Patents [OSTI]

    Girling, Peter M.

    1986-01-01

    A temperature differential detection device for detecting the temperature differential between predetermined portions of a container wall is disclosed as comprising a Wheatstone bridge circuit for detecting resistance imbalance with a first circuit branch having a first elongated wire element mounted in thermal contact with a predetermined portion of the container wall, a second circuit branch having a second elongated wire element mounted in thermal contact with a second predetermined portion of a container wall with the wire elements having a predetermined temperature-resistant coefficient, an indicator interconnected between the first and second branches remote from the container wall for detecting and indicating resistance imbalance between the first and second wire elements, and connector leads for electrically connecting the wire elements to the remote indicator in order to maintain the respective resistance value relationship between the first and second wire elements. The indicator is calibrated to indicate the detected resistance imbalance in terms of a temperature differential between the first and second wall portions.

  5. Temperature differential detection device

    DOE Patents [OSTI]

    Girling, P.M.

    1986-04-22

    A temperature differential detection device for detecting the temperature differential between predetermined portions of a container wall is disclosed as comprising a Wheatstone bridge circuit for detecting resistance imbalance with a first circuit branch having a first elongated wire element mounted in thermal contact with a predetermined portion of the container wall, a second circuit branch having a second elongated wire element mounted in thermal contact with a second predetermined portion of a container wall with the wire elements having a predetermined temperature-resistant coefficient, an indicator interconnected between the first and second branches remote from the container wall for detecting and indicating resistance imbalance between the first and second wire elements, and connector leads for electrically connecting the wire elements to the remote indicator in order to maintain the respective resistance value relationship between the first and second wire elements. The indicator is calibrated to indicate the detected resistance imbalance in terms of a temperature differential between the first and second wall portions. 2 figs.

  6. ARM - Measurement - Sea surface temperature

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Sea surface temperature The temperature of sea water near the surface. Categories Surface Properties Instruments The above measurement is considered scientifically relevant for the...

  7. High Temperature Membrane Working Group

    Broader source: Energy.gov [DOE]

    The High Temperature Membrane Working Group consists of government, industry, and university researchers interested in developing high temperature membranes for fuel cells.

  8. ARM - Measurement - Surface skin temperature

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    surface skin temperature, from an IR thermometer measuring the narrowband radiating temperature of the ground surface in its field of view. Categories Radiometric, Surface...

  9. Zero Temperature Hope Calculations

    SciTech Connect (OSTI)

    Rozsnyai, B F

    2002-07-26

    The primary purpose of the HOPE code is to calculate opacities over a wide temperature and density range. It can also produce equation of state (EOS) data. Since the experimental data at the high temperature region are scarce, comparisons of predictions with the ample zero temperature data provide a valuable physics check of the code. In this report we show a selected few examples across the periodic table. Below we give a brief general information about the physics of the HOPE code. The HOPE code is an ''average atom'' (AA) Dirac-Slater self-consistent code. The AA label in the case of finite temperature means that the one-electron levels are populated according to the Fermi statistics, at zero temperature it means that the ''aufbau'' principle works, i.e. no a priory electronic configuration is set, although it can be done. As such, it is a one-particle model (any Hartree-Fock model is a one particle model). The code is an ''ion-sphere'' model, meaning that the atom under investigation is neutral within the ion-sphere radius. Furthermore, the boundary conditions for the bound states are also set at the ion-sphere radius, which distinguishes the code from the INFERNO, OPAL and STA codes. Once the self-consistent AA state is obtained, the code proceeds to generate many-electron configurations and proceeds to calculate photoabsorption in the ''detailed configuration accounting'' (DCA) scheme. However, this last feature is meaningless at zero temperature. There is one important feature in the HOPE code which should be noted; any self-consistent model is self-consistent in the space of the occupied orbitals. The unoccupied orbitals, where electrons are lifted via photoexcitation, are unphysical. The rigorous way to deal with that problem is to carry out complete self-consistent calculations both in the initial and final states connecting photoexcitations, an enormous computational task. The Amaldi correction is an attempt to address this problem by distorting the outer part of the self-consistent potential in such a way that in the final state after photoexcitation or photoionization the newly occupied orbital sees the hole left in the initial state. This is very important to account for the large number of Rydberg states in the case of low densities. In the next Section we show calculated photoabsorptions compared with experimental data in figures with some rudimentary explanations.

  10. Localized temperature stability of low temperature cofired ceramics

    DOE Patents [OSTI]

    Dai, Steven Xunhu

    2013-11-26

    The present invention is directed to low temperature cofired ceramic modules having localized temperature stability by incorporating temperature coefficient of resonant frequency compensating materials locally into a multilayer LTCC module. Chemical interactions can be minimized and physical compatibility between the compensating materials and the host LTCC dielectrics can be achieved. The invention enables embedded resonators with nearly temperature-independent resonance frequency.

  11. Residential Energy Consumption Survey (RECS) - Analysis & Projections...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    EIA has conducted the Residential Energy Consumption Survey (RECS) since 1978 to provide data on home energy characteristics, end uses of energy, and expenses for the four Census ...

  12. Residential Energy Consumption Survey (RECS) - Analysis & Projections...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    As a part of the Residential Energy Consumption Survey (RECS), trained interviewers measure the square footage of each housing unit. RECS square footage data allow comparison of ...

  13. Commercial Buildings Energy Consumption Survey (CBECS) - Analysis...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Release Date: July 12, 2012 | Revised Date: June 19, 2014 The Commercial Buildings Energy Consumption Survey (CBECS) project cycle spans at least four years, beginning with ...

  14. Commercial Buildings Energy Consumption Survey (CBECS) - Analysis...

    Gasoline and Diesel Fuel Update (EIA)

    Pick a date range: From: To: Go Commercial Buildings Available formats 2012 Commercial Buildings Energy Consumption Survey: Energy Usage Summary Released: March 18, 2016 EIA has ...

  15. Commercial Buildings Energy Consumption Survey (CBECS) - How...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Energy Usage Information Collected in the 2012 CBECS? CBECS 2012 - Release date: March 18, 2016 The Commercial Buildings Energy Consumption Survey (CBECS) project cycle spans at ...

  16. Residential Energy Consumption Survey (RECS) - Analysis & Projections...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    RECS 2009 - Release date: March 28, 2011 First results from EIA's 2009 Residential Energy Consumption Survey (RECS) The 2009 RECS collected home energy characteristics data from ...

  17. Commercial Buildings Energy Consumption Survey (CBECS) - Analysis...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Data collection for the 2012 Commercial Buildings Energy Consumption Survey (CBECS) took place between April and November 2013, collecting data for reference year 2012. The goal of ...

  18. Wyoming State Geological Survey | Open Energy Information

    Open Energy Info (EERE)

    navigation, search Name: Wyoming State Geological Survey Abbreviation: WSGS Address: P.O. Box 1347 Place: Laramie, Wyoming Zip: 82073 Year Founded: 1933 Phone Number:...

  19. 2007/2008 User Survey Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    all six DOE Science Offices and a variety of home institutions: see Respondent Demographics. The survey responses provide feedback about every aspect of NERSC's operation,...

  20. 2009/2010 User Survey Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Next 20092010 User Survey Results Table of Contents Response Summary Respondent Demographics Overall Satisfaction All Satisfaction and Importance Ratings HPC Resources NERSC...

  1. 2010/2011 User Survey Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Next 20102011 User Survey Results Table of Contents Response Summary Respondent Demographics Score Legend Satisfaction and Importance Scores HPC Resources Software Services...

  2. LANSCE | User Resources | User Satisfaction Survey

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    User Satisfaction Survey We hope that your research at the Los Alamos Neutron Science Center was productive and successful. Your feedback is important to the Department of Energy...

  3. radiological survey | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    San Francisco Bay Area Aerial Radiation Assessment Survey (SAN JOSE and SAN FRANCISCO, California) - A helicopter may be seen flying at low altitudes over portions of the San ...

  4. Ground Gravity Survey | Open Energy Information

    Open Energy Info (EERE)

    Et Al., 2000) Dixie Valley Geothermal Area 1999 2000 Precise Gravimetry and Geothermal Reservoir Management Ground Gravity Survey At Dixie Valley Geothermal Area (Blackwell, Et...

  5. Aeromagnetic Survey And Interpretation, Ascention Island, South...

    Open Energy Info (EERE)

    And Interpretation, Ascention Island, South Atlantic Ocean Jump to: navigation, search OpenEI Reference LibraryAdd to library Journal Article: Aeromagnetic Survey And...

  6. FAQs for Survey Form EIA-7A

    Gasoline and Diesel Fuel Update (EIA)

    ... See the EIA Glossary for other coal definitions. How does EIA classify coal rank? Rank ... Form(Includes Instructions). Calculator Conversion calculator Who can I contact? Survey ...

  7. FAQs for Survey Form EIA-8A

    Gasoline and Diesel Fuel Update (EIA)

    ... See the EIA Glossary for other coal definitions. How does EIA classify coal rank? Rank ... Form (Includes Instructions) Calculator Conversion calculator Who can I contact? Survey ...

  8. FAQs for Survey Form EIA-3

    Gasoline and Diesel Fuel Update (EIA)

    ... See the EIA Glossary for coal definitions. How does EIA classify coal rank? Rank types ... Forms (Includes Instructions) Calculator Conversion calculator Who can I contact? Survey ...

  9. Geothermal resistivity resource evaluation survey Waunita Hot...

    Open Energy Info (EERE)

    resistivity resource evaluation survey Waunita Hot Springs project, Gunnison County, Colorado Jump to: navigation, search OpenEI Reference LibraryAdd to library Report: Geothermal...

  10. Pre-Award Accounting System Survey

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    PRE-AWARD ACCOUNTING SYSTEM SURVEY Applicant: Funding Opportunity AnnouncementSolicitation No.: This accounting system review is designed to determine the adequacy and suitability...

  11. FAQs for Survey Form EIA-14

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    These prices are published in the following tables of the Petroleum Marketing Monthly ... If you are interested in receiving this free software, contact the Survey Respondent ...

  12. FAQs for Survey Form EIA-182

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    price(s) are published in the Petroleum Marketing Monthly, the Monthly Energy Review, the ... If you are interested in receiving this free software, contact the Survey Respondent ...

  13. Aeromagnetic Survey (Nannini, 1986) | Open Energy Information

    Open Energy Info (EERE)

    These surveys are based on the magnetic susceptibility contrast between magmatic rocks at depth and the sedimentary formations above. References Raffaello Nannini (1986)...

  14. Federal Buildings Supplemental Survey - Index Page

    U.S. Energy Information Administration (EIA) Indexed Site

    Buildings 1993 Federal Buildings Supplemental Survey Overview Full Report Tables Energy usage and energy costs, by building characteristics, for federally-owned buildings in...

  15. Engine Cylinder Temperature Control

    DOE Patents [OSTI]

    Kilkenny, Jonathan Patrick; Duffy, Kevin Patrick

    2005-09-27

    A method and apparatus for controlling a temperature in a combustion cylinder in an internal combustion engine. The cylinder is fluidly connected to an intake manifold and an exhaust manifold. The method and apparatus includes increasing a back pressure associated with the exhaust manifold to a level sufficient to maintain a desired quantity of residual exhaust gas in the cylinder, and varying operation of an intake valve located between the intake manifold and the cylinder to an open duration sufficient to maintain a desired quantity of fresh air from the intake manifold to the cylinder, wherein controlling the quantities of residual exhaust gas and fresh air are performed to maintain the temperature in the cylinder at a desired level.

  16. HIGH TEMPERATURE THERMOCOUPLE

    DOE Patents [OSTI]

    Eshayu, A.M.

    1963-02-12

    This invention contemplates a high temperature thermocouple for use in an inert or a reducing atmosphere. The thermocouple limbs are made of rhenium and graphite and these limbs are connected at their hot ends in compressed removable contact. The rhenium and graphite are of high purity and are substantially stable and free from diffusion into each other even without shielding. Also, the graphite may be thick enough to support the thermocouple in a gas stream. (AEC)

  17. High-Temperature Materials

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Temperature Materials - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management Programs Advanced

  18. INNOVATIVE INSTRUMENTATION AND ANALYSIS OF THE TEMPERATURE MEASUREMENT FOR HIGH TEMPERATURE GASIFICATION

    SciTech Connect (OSTI)

    Seong W. Lee

    2003-09-01

    During this reporting period, the literature survey including the gasifier temperature measurement literature, the ultrasonic application and its background study in cleaning application, and spray coating process are completed. The gasifier simulator (cold model) testing has been successfully conducted. Four factors (blower voltage, ultrasonic application, injection time intervals, particle weight) were considered as significant factors that affect the temperature measurement. The Analysis of Variance (ANOVA) was applied to analyze the test data. The analysis shows that all four factors are significant to the temperature measurements in the gasifier simulator (cold model). The regression analysis for the case with the normalized room temperature shows that linear model fits the temperature data with 82% accuracy (18% error). The regression analysis for the case without the normalized room temperature shows 72.5% accuracy (27.5% error). The nonlinear regression analysis indicates a better fit than that of the linear regression. The nonlinear regression model's accuracy is 88.7% (11.3% error) for normalized room temperature case, which is better than the linear regression analysis. The hot model thermocouple sleeve design and fabrication are completed. The gasifier simulator (hot model) design and the fabrication are completed. The system tests of the gasifier simulator (hot model) have been conducted and some modifications have been made. Based on the system tests and results analysis, the gasifier simulator (hot model) has met the proposed design requirement and the ready for system test. The ultrasonic cleaning method is under evaluation and will be further studied for the gasifier simulator (hot model) application. The progress of this project has been on schedule.

  19. High Temperature Membrane Working Group

    Broader source: Energy.gov [DOE]

    This presentation provides an overview of the High Temperature Membrane Working Group Meeting in May 2007.

  20. 2006 XSD Scientific Software User Survey.

    SciTech Connect (OSTI)

    Jemian, P. R.

    2007-01-22

    In preparation for the 2006 XSD Scientific Software workshop, our committee sent a survey on June 16 to 100 users in the APS user community. This report contains the survey and the responses we received. The responses are presented in the order received.

  1. High temperature detonator

    DOE Patents [OSTI]

    Johnson, James O. (Los Alamos, NM); Dinegar, Robert H. (Los Alamos, NM)

    1988-01-01

    A detonator assembly is provided which is usable at high temperatures about 300.degree. C. A detonator body is provided with an internal volume defining an anvil surface. A first acceptor explosive is disposed on the anvil surface. A donor assembly having an ignition element, an explosive material, and a flying plate, are placed in the body effective to accelerate the flying plate to impact the first acceptor explosive on the anvil for detonating the first acceptor explosive. A second acceptor explosive is eccentrically located in detonation relationship with the first acceptor explosive to thereafter effect detonation of a main charge.

  2. Drexel University Temperature Sensors

    SciTech Connect (OSTI)

    K. L. Davis; D. L. Knudson; J. L. Rempe; B. M. Chase

    2014-09-01

    This document summarizes background information and presents results related to temperature measurements in the Advanced Test Reactor (ATR) National Scientific User Facility (NSUF) Drexel University Project 31091 irradiation. The objective of this test was to assess the radiation performance of new ceramic materials for advanced reactor applications. Accordingly, irradiations of transition metal carbides and nitrides were performed using the Hydraulic Shuttle Irradiation System (HSIS) in the B-7 position and in static capsules inserted into the A-3 and East Flux Trap Position 5 locations of the ATR.

  3. Thermionic converter temperature controller

    DOE Patents [OSTI]

    Shaner, Benjamin J. (McMurray, PA); Wolf, Joseph H. (Pittsburgh, PA); Johnson, Robert G. R. (Trafford, PA)

    2001-04-24

    A method and apparatus for controlling the temperature of a thermionic reactor over a wide range of operating power, including a thermionic reactor having a plurality of integral cesium reservoirs, a honeycomb material disposed about the reactor which has a plurality of separated cavities, a solid sheath disposed about the honeycomb material and having an opening therein communicating with the honeycomb material and cavities thereof, and a shell disposed about the sheath for creating a coolant annulus therewith so that the coolant in the annulus may fill the cavities and permit nucleate boiling during the operation of the reactor.

  4. Wetland and Sensitive Species Survey Report for Y-12: Proposed Uranium Processing Facility (UPF)

    SciTech Connect (OSTI)

    Giffen, N.; Peterson, M.; Reasor, S.; Pounds, L.; Byrd, G.; Wiest, M. C.; Hill, C. C.

    2009-11-01

    This report summarizes the results of an environmental survey conducted at sites associated with the proposed Uranium Processing Facility (UPF) at the Y-12 National Security Complex in September-October 2009. The survey was conducted in order to evaluate potential impacts of the overall project. This project includes the construction of a haul road, concrete batch plant, wet soil storage area and dry soil storage area. The environmental surveys were conducted by natural resource experts at ORNL who routinely assess the significance of various project activities on the Oak Ridge Reservation (ORR). Natural resource staff assistance on this project included the collection of environmental information that can aid in project location decisions that minimize impacts to sensitive resource such as significant wildlife populations, rare plants and wetlands. Natural resources work was conducted in various habitats, corresponding to the proposed areas of impact. Thc credentials/qualifications of the researchers are contained in Appendix A. The proposed haul road traverses a number of different habitats including a power-line right-of-way. wetlands, streams, forest and mowed areas. It extends from what is known as the New Salvage Yard on the west to the Polaris Parking Lot on the east. This haul road is meant to connect the proposed concrete batch plant to the UPF building site. The proposed site of the concrete batch plant itself is a highly disturbed fenced area. This area of the project is shown in Fig. 1. The proposed Wet Soils Disposal Area is located on the north side of Bear Creek Road at the former Control Burn Study Area. This is a second growth arce containing thick vegetation, and extensive dead and down woody material. This area of the project is shown in Fig. 2. Thc dry soils storage area is proposed for what is currently known as the West Borrow Area. This site is located on the west side of Reeves Road south of Bear Creek Road. The site is an early successional field. This area of the project is shown in Fig. 2.

  5. Innovative Instrumentation and Analysis of the Temperature Measurement for High Temperature Gasification

    SciTech Connect (OSTI)

    Seong W. Lee

    2006-09-30

    The project entitled, ''Innovative Instrumentation and Analysis of the Temperature Measurement for High Temperature Gasification'', was successfully completed by the Principal Investigator, Dr. S. Lee and his research team in the Center for Advanced Energy Systems and Environmental Control Technologies at Morgan State University. The major results and outcomes were presented in semi-annual progress reports and annual project review meetings/presentations. Specifically, the literature survey including the gasifier temperature measurement, the ultrasonic application in cleaning application, and spray coating process and the gasifier simulator (cold model) testing has been successfully conducted during the first year. The results show that four factors (blower voltage, ultrasonic application, injection time intervals, particle weight) were considered as significant factors that affect the temperature measurement. Then the gasifier simulator (hot model) design and the fabrication as well as the systematic tests on hot model were completed to test the significant factors on temperature measurement in the second year. The advanced Industrial analytic methods such as statistics-based experimental design, analysis of variance (ANOVA) and regression methods were applied in the hot model tests. The results show that operational parameters (i.e. air flow rate, water flow rate, fine dust particle amount, ammonia addition) presented significant impact on the temperature measurement inside the gasifier simulator. The experimental design and ANOVA are very efficient way to design and analyze the experiments. The results show that the air flow rate and fine dust particle amount are statistically significant to the temperature measurement. The regression model provided the functional relation between the temperature and these factors with substantial accuracy. In the last year of the project period, the ultrasonic and subsonic cleaning methods and coating materials were tested/applied on the thermocouple cleaning according to the proposed approach. Different frequency, application time and power of the ultrasonic/subsonic output were tested. The results show that the ultrasonic approach is one of the best methods to clean the thermocouple tips during the routine operation of the gasifier. In addition, the real time data acquisition system was also designed and applied in the experiments. This advanced instrumentation provided the efficient and accurate data acquisition for this project. In summary, the accomplishment of the project provided useful information of the ultrasonic cleaning method applied in thermocouple tip cleaning. The temperature measurement could be much improved both in accuracy and duration provided that the proposed approach is widely used in the gasification facilities.

  6. Low temperature methanol process

    SciTech Connect (OSTI)

    O'Hare, T.E.; Sapienza, R.S.; Mahajan, D.; Skaperdas, G.T.

    1986-06-01

    The world's abundant natural gas resources could provide methanol in fuel quantities to the utility system. Natural gas liquefaction is the current major option available for international export transport of natural gas. Gas production is on the increase and international trade even more so, with LNG making most progress. The further penetration of natural gas into distant markets can be substantially increased by a new methanol synthesis process under development. The new methanol process is made possible by the discovery of a catalyst that drops synthesis temperatures from about 275/sup 0/C to about 100/sup 0/C. Furthermore, the new catalyst is a liquid phase system, which permits the synthesis reaction to proceed at fully isothermal conditions. Therefore, the new low temperature liquid catalyst can convert synthesis gas completely to methanol in a single pass through the methanol synthesis reactor. This characteristic leads to a further major improvement in the methanol plant. Atmospheric nitrogen can be tolerated in the synthesis gas, and still the volume of gas fed to the reactor can be smaller than the volume of gas that must be fed to the reactor when accommodating the very low conversions furnished by the best of currently available catalysts. The energy disadvantage of the methanol option must be balanced against the advantage of a much lower capital investment requirement made possible by the new BNL synthesis. Preliminary estimates show that methanol conversion and shipping require an investment for liquefaction to methanol, and shipping liquefied methanol that can range from 35 to 50% of that needed for the LNG plant and LNG shipping fleet.

  7. Please take the 2011 user survey

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    take the 2011 user survey Please take the 2011 user survey June 6, 2011 by Francesca Verdier You are encouraged to take the 2011 user survey. Your answers are important to us and to our program sponsors in DOE. Subscribe via RSS Subscribe Browse by Date May 2016 April 2016 January 2016 December 2015 November 2015 October 2015 September 2015 August 2015 July 2015 April 2015 March 2015 January 2015 December 2014 November 2014 October 2014 August 2014 June 2014 May 2014 April 2014 March 2014

  8. High-temperature-measuring device

    DOE Patents [OSTI]

    Not Available

    1981-01-27

    A temperature measuring device for very high design temperatures (to 2000/sup 0/C) is described. The device comprises a homogenous base structure preferably in the form of a sphere or cylinder. The base structure contains a large number of individual walled cells. The base structure has a decreasing coefficient of elasticity within the temperature range being monitored. A predetermined quantity of inert gas is confined within each cell. The cells are dimensonally stable at the normal working temperature of the device. Increases in gaseous pressure within the cells will permanently deform the cell walls at temperatures within the high temperature range to be measured. Such deformation can be correlated to temperature by calibrating similarly constructed devices under known time and temperature conditions.

  9. Gravity Survey of the Carson Sink - Data and Maps

    SciTech Connect (OSTI)

    Faulds, James E.

    2013-12-31

    A detailed gravity survey was carried out for the entire Carson Sink in western Nevada (Figure 1) through a subcontract to Zonge Engineering, Inc. The Carson Sink is a large composite basin containing three known, blind high‐temperature geothermal systems (Fallon Airbase, Stillwater, and Soda Lake). This area was chosen for a detailed gravity survey in order to characterize the gravity signature of the known geothermal systems and to identify other potential blind systems based on the structural setting indicated by the gravity data. Data: Data were acquired at approximately 400, 800, and 1600 meter intervals for a total of 1,243 stations. The project location and station location points are presented in Figure 14. The station distribution for this survey was designed to complete regional gravity coverage in the Carson Sink area without duplication of available public and private gravity coverage. Gravity data were acquired using a Scintrex CG‐5 gravimeter and a LaCoste and Romberg (L&R) Model‐G gravimeter. The CG‐5 gravity meter has a reading resolution of 0.001 milligals and a typical repeatability of less than 0.005 milligals. The L&R gravity meter has a reading resolution of 0.01 milligals and a typical repeatability of 0.02 milligals. The basic processing of gravimeter readings to calculate through to the Complete Bouguer Anomaly was made using the Gravity and Terrain Correction software version 7.1 for Oasis Montaj by Geosoft LTD. Results: The gravity survey of the Carson Sink yielded the following products. Project location and station location map (Figure 14). Complete Bouguer Anomaly @ 2.67 gm/cc reduction density. Gravity Complete Bouguer Anomaly at 2.50 g/cc Contour Map (Figure 15). Gravity Horizontal Gradient Magnitude Shaded Color Contour Map. Gravity 1st Vertical Derivative Color Contour Map. Interpreted Depth to Mesozoic Basement (Figure 16), incorporating drill‐hole intercept values. Preliminary Interpretation of Results: The Carson Sink is a complex composite basin with several major depocenters (Figures 15 and 16). Major depocenters are present in the south‐central, east‐central, and northeastern parts of the basin. The distribution of gravity anomalies suggests a complex pattern of faulting in the subsurface of the basin, with many fault terminations, step‐overs, and accommodation zones. The pattern of faulting implies that other, previously undiscovered blind geothermal systems are likely in the Carson Sink. The gravity survey was completed near the end of this project. Thus, more thorough analysis of the data and potential locations of blind geothermal systems is planned for future work.

  10. Battery system with temperature sensors

    DOE Patents [OSTI]

    Wood, Steven J.; Trester, Dale B.

    2012-11-13

    A battery system to monitor temperature includes at least one cell with a temperature sensing device proximate the at least one cell. The battery system also includes a flexible member that holds the temperature sensor proximate to the at least one cell.

  11. PbTe/TAGS RTG Mars Environmental Survey (MESUR) mission

    SciTech Connect (OSTI)

    Schock, A. )

    1993-01-10

    The paper describes the results of studies on an RTG option for powering the global network of unmanned landers for NASA's Mars Environmental Survey (MESUR) mission. RTGs are essentially unaffected by diurnal and seasonal variations, Martian sandstorms, and landing site latitudes, and their waste heat can stabilize the temperatures of the landers and their payload. The RTG designs described in this paper are based on PbTe/TAGS thermoelectric elements, in contast to the SiGe-based RTGs the author described in previous publications. The presently described RTGs differ not only in the choice of thermoelectric materials but also in the use of much lower operating temperatures, conductive rather than radiative heat transfer, an inert cover gas instead of vacuum in the RTG's converter, and fibrous instead of multifoil thermal insulation. As in a previous Teledyne design, the Fairchild designs described in this paper employ flight-proven General Purpose Source modules and Close-Pack Arrays of thermoelectric converter modules. Illustrative point designs of RTGs producing 41 and 51 watts(e) at 28 volts are presented. The presented performance parameters were derived by detailed thermal, thermoelectric, and electrical analyses (including radiator geometry optimization) described in the paper. The Fairchild study showed that, with appropriate modifications, the Teledyne design can be scaled up to higher power levels, and it identified solutions to ensure adequate fuel clad ductility at launch temperatures and adequate thermal conductance from the thermoelectric cold ends to the RTG housing.

  12. Residential Energy Consumption Survey (RECS) - Analysis & Projections...

    Gasoline and Diesel Fuel Update (EIA)

    How does EIA estimate energy consumption and end uses in U.S. homes? RECS 2009 - Release date: March 28, 2011 EIA administers the Residential Energy Consumption Survey (RECS) to a ...

  13. Commercial Buildings Energy Consumption Survey (CBECS) - Data...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    What is an RSE? The estimates in the Commercial Buildings Energy Consumption Survey (CBECS) are based on data reported by representatives of a statistically-designed subset of the ...

  14. Geothermal Energy Growth Continues, Industry Survey Reports

    Broader source: Energy.gov [DOE]

    A survey released by the Geothermal Energy Association (GEA) shows continued growth in the number of new geothermal power projects under development in the United States, a 20% increase since January of this year.

  15. 2008 B20 Survey Results (Presentation)

    SciTech Connect (OSTI)

    Alleman, T. L.; McCormick, R. L.

    2009-02-02

    Describes results of a sample survey of the quality of B20, a biodiesel blend, collected from U.S. public pumps and fleets as part of a joint effort by NREL, the NBB, and engine manufacturers.

  16. Mediation Survey Form | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PDF icon Mediation Survey Form More Documents & Publications Microsoft Word - GC Mediation Evaluation 2-06-09.doc Mediation Brochure FIA-12-0044 - In the Matter of Cynthia Brown...

  17. FAQs for Survey Form EIA-782C

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    ... software, contact the Survey Respondent Service Team at 202-586-9659. Where can I find published data from the EIA-782C? These data are published in the Petroleum Marketing ...

  18. FAQs for Survey Form EIA-821

    Gasoline and Diesel Fuel Update (EIA)

    of your email. Should I report biodiesel on the EIA-821 survey? Report B2, B5, or B20 biodiesel under the primary fuel type with which it was blended and the type of customer...

  19. LOS ALAMOS NATIONAL LABORATORY COMMUNITY LEADERS SURVEY

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    LOS ALAMOS NATIONAL LABORATORY COMMUNITY LEADERS SURVEY SEPTEMBER 2013 LOS ALAMOS NATIONAL LABORATORY-COMMUNITY LEADERS STUDY SEPTEMBER 2013 PAGE 2 RESEARCH & POLLING, INC. TABLE OF CONTENTS I. INTRODUCTION ....................................................................................................................................................................................................................................................... 3 METHODOLOGY

  20. Commercial Grade Dedication Survey and Training

    Broader source: Energy.gov [DOE]

    This survey was conducted to obtain input from EM contractors on processes used to perform Commercial Grade Item (CGI) dedication.  The intended use of this information is to form the basis for...

  1. 2012 Hanford Climate Survey Report - ATL Report

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ATL Report Prepared by EurekaFacts LLC 1 Table of Contents Introduction.................................................................................................................................................... 2 Safety Culture and Climate Focus Areas and Factors .................................................................................. 3 Interpreting the Survey Results Presented in this Report ............................................................................. 4 Key

  2. 2012 Hanford Climate Survey Report - CHPRC Report

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CHPRC Report Prepared by EurekaFacts LLC 1 Table of Contents Introduction.................................................................................................................................................... 2 Safety Culture and Climate Focus Areas and Factors .................................................................................. 3 Interpreting the Survey Results Presented in this Report ............................................................................. 4 Key

  3. 2012 Hanford Climate Survey Report - MSA Report

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MSA Report Prepared by EurekaFacts LLC 1 Table of Contents Introduction.................................................................................................................................................... 2 Safety Culture and Climate Focus Areas and Factors .................................................................................. 3 Interpreting the Survey Results Presented in this Report ............................................................................. 4 Key

  4. 2012 Hanford Climate Survey Report - WCH Report

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    WCH Report Prepared by EurekaFacts LLC 1 Table of Contents Introduction.................................................................................................................................................... 2 Safety Culture and Climate Focus Areas and Factors .................................................................................. 3 Interpreting the Survey Results Presented in this Report ............................................................................. 4 Key

  5. 2012 Hanford Climate Survey Report - WRPS Report

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    WRPS Report Prepared by EurekaFacts LLC 1 Table of Contents Introduction.................................................................................................................................................... 2 Safety Culture and Climate Focus Areas and Factors .................................................................................. 3 Interpreting the Survey Results Presented in this Report ............................................................................. 4 Key

  6. NEPA effectiveness -- a survey of academics

    SciTech Connect (OSTI)

    Canter, L.; Clark, R.

    1997-09-01

    The National Environmental Policy Act (NEPA) went into effect in the United States on January 1, 1970, just over 25 years ago. In light of this milestone, a survey of academics on the effectiveness of NEPA has been conducted regarding the preparation of environmental assessments (EAs) or environmental impact statements (EISs). This paper summarizes the results of a survey of 31 academics in 12 disciplines from 21 states. Several strengths of NEPA were identified, most importantly that NEPA encourages agencies and decision makers: (1) to acknowledge potential environmental consequences to the public, thus opening up the decision process; and (2) to think about environmental consequences before resources are committed. Surveyed participants also prioritized needs for improvement. While this survey was focused on the NEPA process in the United States, the identified issues have implications for the worldwide practice of environmental impact assessment. Finally, recommendations are described that are primarily associated with guidance, possible modifications in the NEPA process and follow-on training.

  7. Survey Says: Workplace Charging is Growing in Popularity and Impact |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Survey Says: Workplace Charging is Growing in Popularity and Impact Survey Says: Workplace Charging is Growing in Popularity and Impact November 18, 2014 - 3:54pm Addthis Survey Says: Workplace Charging is Growing in Popularity and Impact Survey Says: Workplace Charging is Growing in Popularity and Impact Survey Says: Workplace Charging is Growing in Popularity and Impact Survey Says: Workplace Charging is Growing in Popularity and Impact Sarah Olexsak Workplace Charging

  8. 2009 - Federal Viewpoint Survey Reports | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    09 - Federal Viewpoint Survey Reports 2009 - Federal Viewpoint Survey Reports The 2009 Trend report provides summary results for the Department or Energy's portion of the Federal Employee Viewpoint Survey. The report also shows how the 2009 results compare to the results of previous years. PDF icon 2009 Annual Employee Survey Results PDF icon 2009 Annual Employee Survey Comparison Report PDF icon 2009 Annual Employee Survey Trend Report Responsible Contacts Thomasina Mathews PROGRAM MANAGER

  9. Department of Energy Earned Value Management Survey Results | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Department of Energy Earned Value Management Survey Results Department of Energy Earned Value Management Survey Results Humphreys & Associates, Inc. (H&A) conducted a survey of Department of Energy (DOE) Earned Value Management (EVM) and Project Management (PM) stakeholders. Two versions of the survey were distributed: DOE Federal Staff Survey (inclusive of DOE employees and contracted staff support) and the Capital Asset Project Contractors Survey (inclusive of DOE prime

  10. Directory and survey of particle physicists

    SciTech Connect (OSTI)

    1997-04-01

    In order to develop a clearer understanding of the demographics of the U.S. particle physics workforce, the US Department of Energy, the National Science Foundation, and the Division of Particles and Fields of the American Physical Society commissioned a survey and census of particle physicists employed in the United States. This survey and census were conducted in 1995, with an update of the census in April 1997. The agencies and the scientific community were represented for the 1995 efforts by Dr. Robert Woods (DOE), Dr. William Chinowsky (NSF), and Prof. Uriel Nauenberg (DPF); for the current census, by Dr. Robert Diebold (DOE), Dr. Marvin Goldberg (NSF), and Dr. Patricia Rankin (NSF). The survey/census were carried out with the assistance of the Particle Data Group at Lawrence Berkeley National Laboratory. In order to obtain an accurate study of the current workforce and of future needs, we requested that all HEP physicists fill out and return the 1995 survey. There were 2494 respondents. For the 1997 census, a representative of each university and laboratory was asked to provide information on all persons at that institution who spend at least 50% of their research time on particle physics. In some cases this includes accelerator physicists. The total number of physicists in the 1997 census is 3492 from 155 institutions in the United States. The full survey questionnaires are shown. The primary one was addressed to individual particle physicists, while the secondary one was addressed to principal investigators and sought information about people leaving the field. There are many possible tables and plots from this survey, with a variety of correlations. Those chosen are representative of a cross-section of the demographic results. It should be emphasized that this survey was a snapshot in time, and does not have the same capabilities as would a series of surveys that are periodic in time. Care should be taken in interpreting the results of the tables and plots.

  11. Technetium Immobilization Forms Literature Survey

    SciTech Connect (OSTI)

    Westsik, Joseph H.; Cantrell, Kirk J.; Serne, R. Jeffrey; Qafoku, Nikolla

    2014-05-01

    Of the many radionuclides and contaminants in the tank wastes stored at the Hanford site, technetium-99 (99Tc) is one of the most challenging to effectively immobilize in a waste form for ultimate disposal. Within the Hanford Tank Waste Treatment and Immobilization Plant (WTP), the Tc will partition between both the high-level waste (HLW) and low-activity waste (LAW) fractions of the tank waste. The HLW fraction will be converted to a glass waste form in the HLW vitrification facility and the LAW fraction will be converted to another glass waste form in the LAW vitrification facility. In both vitrification facilities, the Tc is incorporated into the glass waste form but a significant fraction of the Tc volatilizes at the high glass-melting temperatures and is captured in the off-gas treatment systems at both facilities. The aqueous off-gas condensate solution containing the volatilized Tc is recycled and is added to the LAW glass melter feed. This recycle process is effective in increasing the loading of Tc in the LAW glass but it also disproportionally increases the sulfur and halides in the LAW melter feed which increases both the amount of LAW glass and either the duration of the LAW vitrification mission or the required supplemental LAW treatment capacity.

  12. High temperature interfacial superconductivity

    DOE Patents [OSTI]

    Bozovic, Ivan; Logvenov, Gennady; Gozar, Adrian Mihai

    2012-06-19

    High-temperature superconductivity confined to nanometer-scale interfaces has been a long standing goal because of potential applications in electronic devices. The spontaneous formation of a superconducting interface in bilayers consisting of an insulator (La.sub.2CuO.sub.4) and a metal (La.sub.1-xSr.sub.xCuO.sub.4), neither of which is superconducting per se, is described. Depending upon the layering sequence of the bilayers, T.sub.c may be either .about.15 K or .about.30 K. This highly robust phenomenon is confined to within 2-3 nm around the interface. After exposing the bilayer to ozone, T.sub.c exceeds 50 K and this enhanced superconductivity is also shown to originate from a 1 to 2 unit cell thick interfacial layer. The results demonstrate that engineering artificial heterostructures provides a novel, unconventional way to fabricate stable, quasi two-dimensional high T.sub.c phases and to significantly enhance superconducting properties in other superconductors. The superconducting interface may be implemented, for example, in SIS tunnel junctions or a SuFET.

  13. Hot Pot Contoured Temperature Gradient Map

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Lane, Michael

    Temperature gradient contours derived from Oski temperature gradient hole program and from earlier published information.

  14. Hot Pot Contoured Temperature Gradient Map

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Lane, Michael

    2013-06-28

    Temperature gradient contours derived from Oski temperature gradient hole program and from earlier published information.

  15. The Sloan Digital Sky Survey Monitor Telescope Pipeline (Journal...

    Office of Scientific and Technical Information (OSTI)

    The Sloan Digital Sky Survey Monitor Telescope Pipeline Citation Details In-Document Search Title: The Sloan Digital Sky Survey Monitor Telescope Pipeline You are accessing a...

  16. Commercial Buildings Energy Consumption Survey (CBECS) - U.S...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    The Commercial Buildings Energy Consumption Survey (CBECS) is a national-level sample survey of commercial buildings and their energy suppliers conducted quadrennially (previously ...

  17. Hubei Electric Power Survey Design Institute | Open Energy Information

    Open Energy Info (EERE)

    Survey Design Institute Jump to: navigation, search Name: Hubei Electric Power Survey&Design Institute Place: Hubei Province, China Product: Wuhan-based power project design and...

  18. Airborne Electromagnetic Survey At Chena Geothermal Area (Kolker...

    Open Energy Info (EERE)

    Phase I) Notes Fugro, Inc. performed an airborne geophysical survey using the DIGHEM (Digital Helicopter ElectroMagnetics) aircraft over a 937 km2 survey grid. An coplanar...

  19. Category:Near Infrared Surveys | Open Energy Information

    Open Energy Info (EERE)

    Infrared Surveys Retrieved from "http:en.openei.orgwindex.php?titleCategory:NearInfraredSurveys&oldid794164" Feedback Contact needs updating Image needs updating...

  20. Idaho Geological Survey and University of Idaho Explore for Geothermal...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Idaho Geological Survey and University of Idaho Explore for Geothermal Energy Idaho Geological Survey and University of Idaho Explore for Geothermal Energy January 11, 2013 -...

  1. Headquarters Facilities Master Security Plan - Chapter 7, Surveys...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    First, survey team members assist HQ program elements in establishing, maintaining, and deactivating their LAs, VTRs, and TLAs. Second, the survey team conducts an annual ...

  2. Ground Gravity Survey At Clear Lake Area (Skokan, 1993) | Open...

    Open Energy Info (EERE)

    Ground Gravity Survey At Clear Lake Area (Skokan, 1993) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey At Clear Lake Area...

  3. Ground Gravity Survey At Coso Geothermal Area (1980) | Open Energy...

    Open Energy Info (EERE)

    Ground Gravity Survey At Coso Geothermal Area (1980) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey At Coso Geothermal...

  4. Ground Gravity Survey At Crump's Hot Springs Area (DOE GTP) ...

    Open Energy Info (EERE)

    Ground Gravity Survey At Crump's Hot Springs Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey At Crump's Hot...

  5. Category:Airborne Gravity Survey | Open Energy Information

    Open Energy Info (EERE)

    Category Edit History Category:Airborne Gravity Survey Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Geothermalpower.jpg Looking for the Airborne Gravity Survey...

  6. Ground Gravity Survey At North Brawley Geothermal Area (Biehler...

    Open Energy Info (EERE)

    Ground Gravity Survey At North Brawley Geothermal Area (Biehler, 1964) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey At...

  7. Ground Gravity Survey At Cove Fort Area - Vapor (Warpinski, Et...

    Open Energy Info (EERE)

    Ground Gravity Survey At Cove Fort Area - Vapor (Warpinski, Et Al., 2002) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey...

  8. Ground Gravity Survey At Kilauea East Rift Geothermal Area (FURUMOTO...

    Open Energy Info (EERE)

    Ground Gravity Survey At Kilauea East Rift Geothermal Area (FURUMOTO, 1976) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey...

  9. Ground Gravity Survey At Snake River Plain Region (DOE GTP) ...

    Open Energy Info (EERE)

    Ground Gravity Survey At Snake River Plain Region (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey At Snake River...

  10. Ground Gravity Survey At Kilauea East Rift Geothermal Area (Thomas...

    Open Energy Info (EERE)

    Ground Gravity Survey At Kilauea East Rift Geothermal Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey...

  11. Title Preactivity Survey Report for Five Tonopah Test Range Explosive...

    National Nuclear Security Administration (NNSA)

    Preactivity Survey Report for Five Tonopah Test Range Explosive Ordnance Disposal Sites ... PREACTIVITY AND RECLAMATION SURVEY REPORTS FOR FIVE TONOPAH TEST RANGE EXPLOSIVE ORDNANCE ...

  12. DOE Initiative to Improve PM and EVM, Integration Survey Results...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Initiative to Improve PM and EVM, Integration Survey Results DOE Initiative to Improve PM and EVM, Integration Survey Results DOE Initiative to Improve PM and EVM, Integration ...

  13. Refraction Survey At Kilauea East Rift Geothermal Area (Broyles...

    Open Energy Info (EERE)

    East Rift Geothermal Area Exploration Technique Refraction Survey Activity Date 1976 - 1977 Usefulness not indicated DOE-funding Unknown Exploration Basis This survey was done as...

  14. Literature Survey of Crude Oil Properties Relevant to Handling...

    Office of Scientific and Technical Information (OSTI)

    Literature Survey of Crude Oil Properties Relevant to Handling and Fire Safety in Transport. Citation Details In-Document Search Title: Literature Survey of Crude Oil Properties ...

  15. Geodetic Survey At Yellowstone Region (Hellman & Ramsey, 2004...

    Open Energy Info (EERE)

    Geodetic Survey At Yellowstone Region (Hellman & Ramsey, 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Geodetic Survey At Yellowstone...

  16. Confirmatory Survey Report for the Quehanna Decommissioning Project, Karthaus, PA

    SciTech Connect (OSTI)

    W. C. Adams

    2007-10-30

    The survey activities consisted of visual inspections and radiological surveys including beta and gamma surface scans and surface beta activity measurements.

  17. Geodetic Survey At Central Nevada Seismic Zone Region (Blewitt...

    Open Energy Info (EERE)

    Geodetic Survey At Central Nevada Seismic Zone Region (Blewitt Et Al, 2005) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Geodetic Survey At...

  18. Manufacturing-Industrial Energy Consumption Survey(MECS) Historical...

    U.S. Energy Information Administration (EIA) Indexed Site

    reports, data tables and questionnaires Released: May 2008 The Manufacturing Energy Consumption Survey (MECS) is a periodic national sample survey devoted to measuring...

  19. Oregon National Register and Survey Program Webpage | Open Energy...

    Open Energy Info (EERE)

    National Register and Survey Program Webpage Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Oregon National Register and Survey Program Webpage...

  20. Direct-Current Resistivity Survey At Kilauea East Rift Geothermal...

    Open Energy Info (EERE)

    the findings from the other resistivity surveys conducted in the area. References James Kauahikaua, Douglas Klein (1978) Results of Electric Survey in the Area of Hawaii...

  1. 70 DA WHITE DWARFS IDENTIFIED IN LAMOST PILOT SURVEY

    SciTech Connect (OSTI)

    Zhao, J. K.; Luo, A. L.; Zhao, G. [Key Laboratory of Optical Astronomy, National Astronomical Observatories, Chinese Academy of Sciences, Beijing 100012 (China); Oswalt, T. D., E-mail: zjk@bao.ac.cn, E-mail: gzhao@bao.ac.cn, E-mail: lal@bao.ac.cn, E-mail: toswalt@fit.edu [Physics and Space Science Department, Florida Institute of Technology, Melbourne, FL 32901 (United States)

    2013-06-01

    We present a spectroscopically identified catalog of 70 DA white dwarfs (WDs) from the LAMOST pilot survey. Thirty-five are found to be new identifications after cross-correlation with the Eisenstein et al. and Villanova catalogs. The effective temperature and gravity of these WDs are estimated by Balmer lines fitting. Most of them are hot WDs. The cooling times and masses of these WDs are estimated by interpolation in theoretical evolution tracks. The peak of the mass distribution is found to be {approx}0.6 M {sub Sun }, which is consistent with prior work in the literature. The distances of these WDs are estimated using the method of synthetic spectral distances. All of these WDs are found to be in the Galactic disk from our analysis of space motions. Our sample supports the expectation that WDs with high mass are concentrated near the plane of the Galactic disk.

  2. Measurement of thermodynamic temperature of high temperature fixed points

    SciTech Connect (OSTI)

    Gavrilov, V. R.; Khlevnoy, B. B.; Otryaskin, D. A.; Grigorieva, I. A.; Samoylov, M. L.; Sapritsky, V. I.

    2013-09-11

    The paper is devoted to VNIIOFI's measurements of thermodynamic temperature of the high temperature fixed points Co-C, Pt-C and Re-C within the scope of the international project coordinated by the Consultative Committee for Thermometry working group 5 'Radiation Thermometry'. The melting temperatures of the fixed points were measured by a radiance mode radiation thermometer calibrated against a filter radiometer with known irradiance spectral responsivity via a high temperature black body. This paper describes the facility used for the measurements, the results and estimated uncertainties.

  3. Studies on three-temperature, three-cylinder Stirling cycle machine (accuracy of vector analysis)

    SciTech Connect (OSTI)

    Ohtomo, Michihiro; Isshiki, Naotsugu; Watanabe, Hiroichi

    1996-12-31

    A Simple vector analysis method aimed to quickly determine the performance of complicated multi-cylinder Stirling cycle machines such as the Vuilleumier cycle machine was introduced by the authors in 1992. It has proven to be a very simple graphic method for the design and analysis of future complicated Stirling cycle machines. In this method, it is assumed that all volume variations and pressure changes are sinusoidal. Actually all volume fluctuations can be assumed to be sinusoidal without large errors, but pressure fluctuation deviates from sinusoidal assumptions, because pressure is a reciprocal of the total sinusoidal volume fluctuation. The pressure value estimated by this vector analysis method is compared to the exact calculation, and the error is calculated and discussed. It is known that the error depends on the pressure ratio and the dead volume ratio, and the error is less than 10% in many cases. The features and details of a newly made experimental, small, pressurized (6MPa) three-temperature (hot, cold and middle temperature), three-cylinder Stirling cycle machine are described. This machine was basically designed by this vector analysis method. This machine can work as a cooler and/or a heat pump, by adjusting the phase angle of the hot cylinder and depending upon whether motor power and/or heat input is supplied. Rotating vector analysis was done on a free piston or a pulse tube machine (Storch, 1988), but this report gives new convenient methods for complicated Stirling cycle systems.

  4. Sensors for low temperature application

    DOE Patents [OSTI]

    Henderson, Timothy M.; Wuttke, Gilbert H.

    1977-01-01

    A method and apparatus for low temperature sensing which uses gas filled micro-size hollow glass spheres that are exposed in a confined observation area to a low temperature range (Kelvin) and observed microscopically to determine change of state, i.e., change from gaseous state of the contained gas to condensed state. By suitable indicia and classification of the spheres in the observation area, the temperature can be determined very accurately.

  5. Actinide Thermodynamics at Elevated Temperatures

    SciTech Connect (OSTI)

    Friese, Judah I.; Rao, Linfeng; Xia, Yuanxian; Bachelor, Paula P.; Tian, Guoxin

    2007-11-16

    The postclosure chemical environment in the proposed Yucca Mountain repository is expected to experience elevated temperatures. Predicting migration of actinides is possible if sufficient, reliable thermodynamic data on hydrolysis and complexation are available for these temperatures. Data are scarce and scattered for 25 degrees C, and nonexistent for elevated temperatures. This collaborative project between LBNL and PNNL collects thermodynamic data at elevated temperatures on actinide complexes with inorganic ligands that may be present in Yucca Mountain. The ligands include hydroxide, fluoride, sulfate, phosphate and carbonate. Thermodynamic parameters of complexation, including stability constants, enthalpy, entropy and heat capacity of complexation, are measured with a variety of techniques including solvent extraction, potentiometry, spectrophotometry and calorimetry

  6. ARM - Measurement - Soil surface temperature

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Systems SOIL : Soil Measurement from the SGP SWATS : Soil Water and Temperature System MET : Surface Meteorological Instrumentation External Instruments ETA : Eta Model Runs...

  7. Low temperature material bonding technique

    DOE Patents [OSTI]

    Ramsey, J. Michael (Knoxville, TN); Foote, Robert S. (Oak Ridge, TN)

    2002-02-12

    A method of performing a lower temperature bonding technique to bond together two mating pieces of glass includes applying a sodium silicate aqueous solution between the two pieces.

  8. Low-Temperature Diesel Combustion

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    EnergyWater History Water Monitoring & Treatment Technology Decision Models for ... Twitter Google + Vimeo GovDelivery SlideShare Low-Temperature Diesel Combustion Home...

  9. Low Temperature Material Bonding Technique

    DOE Patents [OSTI]

    Ramsey, J. Michael (Knoxville, TN); Foote, Robert S. (Oak Ridge, TN)

    2000-10-10

    A method of performing a lower temperature bonding technique to bond together two mating pieces of glass includes applying a sodium silicate aqueous solution between the two pieces.

  10. The variable sky of deep synoptic surveys

    SciTech Connect (OSTI)

    Ridgway, Stephen T.; Matheson, Thomas; Mighell, Kenneth J.; Olsen, Knut A. [National Optical Astronomy Observatory, Tucson, AZ 85725 (United States); Howell, Steve B., E-mail: ridgway@noao.edu [NASA Ames Research Center, P.O. Box 1, M/S 244-30, Moffett Field, CA 94035 (United States)

    2014-11-20

    The discovery of variable and transient sources is an essential product of synoptic surveys. The alert stream will require filtering for personalized criteriaa process managed by a functionality commonly described as a Broker. In order to understand quantitatively the magnitude of the alert generation and Broker tasks, we have undertaken an analysis of the most numerous types of variable targets in the skyGalactic stars, quasi-stellar objects (QSOs), active galactic nuclei (AGNs), and asteroids. It is found that the Large Synoptic Survey Telescope (LSST) will be capable of discovering ?10{sup 5} high latitude (|b| > 20) variable stars per night at the beginning of the survey. (The corresponding number for |b| < 20 is orders of magnitude larger, but subject to caveats concerning extinction and crowding.) However, the number of new discoveries may well drop below 100 per night within less than one year. The same analysis applied to GAIA clarifies the complementarity of the GAIA and LSST surveys. Discovery of AGNs and QSOs are each predicted to begin at ?3000 per night and decrease by 50 times over four years. Supernovae are expected at ?1100 per night, and after several survey years will dominate the new variable discovery rate. LSST asteroid discoveries will start at >10{sup 5} per night, and if orbital determination has a 50% success rate per epoch, they will drop below 1000 per night within two years.

  11. Geothermal industry employment: Survey results & analysis

    SciTech Connect (OSTI)

    Not Available

    2005-09-01

    The Geothermal Energy Association (GEA) is ofteh asked about the socioeconomic and employment impact of the industry. Since available literature dealing with employment involved in the geothermal sector appeared relatively outdated, unduly focused on certain activities of the industry (e.g. operation and maintenance of geothermal power plants) or poorly reliable, GEA, in consultation with the DOE, decided to conduct a new employment survey to provide better answers to these questions. The main objective of this survey is to assess and characterize the current workforce involved in geothermal activities in the US. Several initiatives have therefore been undertaken to reach as many organizations involved in geothermal activities as possible and assess their current workforce. The first section of this document describes the methodology used to contact the companies involved in the geothermal sector. The second section presents the survey results and analyzes them. This analysis includes two major parts. The first part analyzes the survey responses, presents employment numbers that were captured and describes the major characteristics of the industry that have been identified. The second part of the analysis estimates the number of workers involved in companies that are active in the geothermal business but did not respond to the survey or could not be reached. Preliminary conclusions and the study limits and restrictions are then presented. The third section addresses the potential employment impact related to manufacturing and construction of new geothermal power facilities. Indirect and induced economic impacts related with such investment are also investigated.

  12. 2001 FEMP Customer Survey Report (Appendices) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Appendices) 2001 FEMP Customer Survey Report (Appendices) Appendix A: Survey Instrument Appendix B: Detailed Responses Appendix C: Adoption and Diffusion of Innovations PDF icon Appendices More Documents & Publications 2001 FEMP Customer Survey Report (Summary Report) 2001 FEMP Customer Survey Report (Main Report

  13. Industry survey for horizontal wells. Final report

    SciTech Connect (OSTI)

    Wilson, D.D.; Kaback, D.S. [CDM Federal Programs Corp., Denver, CO (United States); Denhan, M.E. [Westinghouse Savannah River Co., Aiken, SC (United States); Watkins, D. [CDM Federal Programs Corp., Aiken, SC (United States)

    1993-07-01

    An international survey of horizontal environmental wells was performed during May and June of 1993. The purpose of the survey was to provide the environmental industry with an inventory of horizontal environmental wells and information pertaining to the extent of the use of horizontal environmental wells, the variety of horizontal environmental well applications, the types of geologic and hydrogeologic conditions within which horizontal environmental wells have been installed, and the companies that perform horizontal environmental well installations. Other information, such as the cost of horizontal environmental well installations and the results of tests performed on the wells, is not complete but is provided as general information with the caveat that the information should not be used to compare drilling companies. The result of the survey is a catalogue of horizontal environmental wells that are categorized by the objective or use of the wells, the vertical depth of the wells, and the drilling company contracted to install the wells.

  14. Ultra High Temperature | Open Energy Information

    Open Energy Info (EERE)

    Ultra High Temperature Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Print PDF Sanyal Temperature Classification: Ultra High Temperature Dictionary.png Ultra High...

  15. Low Temperature/Coproduced/Geopressured Subprogram Overview ...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Low TemperatureCoproducedGeopressured Subprogram Overview Low TemperatureCoproducedGeopressured Subprogram Overview This overview of GTP's Low TemperatureCoproduced...

  16. High Temperature Thermoelectric Materials Characterization for...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    the High Temperature Materials Laboratory (HTML) User Program High Temperature ... the High Temperature Materials Laboratory (HTML) User Program 2009 DOE Hydrogen Program ...

  17. Low Temperature Geothermal Energy | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Low Temperature Geothermal Energy Low Temperature Geothermal Energy Presented at the Technology Planning Workshop for Low-Temperature, Coproduced, and Geopressured Geothermal ...

  18. Utility FGD Survey, January--December 1989

    SciTech Connect (OSTI)

    Hance, S.L.; McKibben, R.S.; Jones, F.M. )

    1992-03-01

    The Utility flue gas desulfurization (FGD) Survey report, which is generated by a computerized data base management system, represents a survey of operational and planned domestic utility flue gas desulfurization (FGD) systems. It summarizes information contributed by the utility industry, system and equipment suppliers, system designers, research organizations, and regulatory agencies. The data cover system design, fuel characteristics, operating history, and actual system performance. Also included is a unit-by-unit discussion of problems and solutions associated with the boilers, scrubbers, and FGD systems. The development status (operational, under construction, or in the planning stages), system supplier, process, waste disposal practice, and regulatory class are tabulated alphabetically by utility company.

  19. Pion dynamics at finite temperature

    SciTech Connect (OSTI)

    Toublan, D.

    1997-11-01

    The pion decay constant and mass are computed at low temperature within chiral perturbation theory to two loops. The effects of the breaking of Lorentz symmetry by the thermal equilibrium state are discussed. The validity of the Gell-Mann{endash}Oakes{endash}Renner relation at finite temperature is examined. {copyright} {ital 1997} {ital The American Physical Society}

  20. High temperature turbine engine structure

    DOE Patents [OSTI]

    Boyd, Gary L.

    1990-01-01

    A high temperature turbine engine includes a hybrid ceramic/metallic rotor member having ceramic/metal joint structure. The disclosed joint is able to endure higher temperatures than previously possible, and aids in controlling heat transfer in the rotor member.

  1. The SDSS-III APOGEE radial velocity survey of M dwarfs. I. Description of the survey and science goals

    SciTech Connect (OSTI)

    Deshpande, R.; Bender, C. F.; Mahadevan, S.; Terrien, R. C.; Schneider, D. P.; Fleming, S. W.; Blake, C. H.; Carlberg, J. K.; Zasowski, G.; Hearty, F.; Crepp, J.; Rajpurohit, A. S.; Reyl, C.; Nidever, D. L.; Prieto, C. Allende; Hernndez, J.; Bizyaev, D.; Ebelke, G.; Frinchaboy, P. M.; Ge, J.; and others

    2013-12-01

    We are carrying out a large ancillary program with the Sloan Digital Sky Survey, SDSS-III, using the fiber-fed multi-object near-infrared APOGEE spectrograph, to obtain high-resolution H-band spectra of more than 1200 M dwarfs. These observations will be used to measure spectroscopic rotational velocities, radial velocities, physical stellar parameters, and variability of the target stars. Here, we describe the target selection for this survey, as well as results from the first year of scientific observations based on spectra that will be publicly available in the SDSS-III DR10 data release. As part of this paper we present radial velocities and rotational velocities of over 200 M dwarfs, with a vsin i precision of ?2 km s{sup 1} and a measurement floor at vsin i = 4 km s{sup 1}. This survey significantly increases the number of M dwarfs studied for rotational velocities and radial velocity variability (at ?100-200 m s{sup 1}), and will inform and advance the target selection for planned radial velocity and photometric searches for low-mass exoplanets around M dwarfs, such as the Habitable Zone Planet Finder, CARMENES, and TESS. Multiple epochs of radial velocity observations enable us to identify short period binaries, and adaptive optics imaging of a subset of stars enables the detection of possible stellar companions at larger separations. The high-resolution APOGEE spectra, covering the entire H band, provide the opportunity to measure physical stellar parameters such as effective temperatures and metallicities for many of these stars. At the culmination of this survey, we will have obtained multi-epoch spectra and radial velocities for over 1400 stars spanning the spectral range M0-L0, providing the largest set of near-infrared M dwarf spectra at high resolution, and more than doubling the number of known spectroscopic vsin i values for M dwarfs. Furthermore, by modeling telluric lines to correct for small instrumental radial velocity shifts, we hope to achieve a relative velocity precision floor of 50 m s{sup 1} for bright M dwarfs. With three or more epochs, this precision is adequate to detect substellar companions, including giant planets with short orbital periods, and flag them for higher-cadence followup. We present preliminary, and promising, results of this telluric modeling technique in this paper.

  2. 2014-Federal Viewpoint Survey Reports | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    4-Federal Viewpoint Survey Reports 2014-Federal Viewpoint Survey Reports The following highlight report focuses on the Department of Energy's areas of strengths and challenges, identifies areas of progress and opportunities for improvement. The Departments 2014 results are compared with the 2013 Government wide results. PDF icon 2014 Federal Employee Viewpoint Survey Results: Annual Employee Survey (AES) Report PDF icon 2014 Federal Employee Viewpoint Survey Results: Agency Management Report

  3. Solar Survey of PV System Owners: San Diego

    Broader source: Energy.gov [DOE]

    The purpose of the survey was to understand the motivation, challenges and benefits perceived by individuals who decided to install solar systems in the City of San Diego. Approximately 2000 surveys were sent, and 641 surveys were completed. The primary response was from the residential sector. Individuals had the option to reply electronically, using Survey Monkey, or to complete a paper survey. All responses were combined and checked to ensure that there were no duplicates.

  4. NITRATE DESTRUCTION LITERATURE SURVEY AND EVALUATION CRITERIA

    SciTech Connect (OSTI)

    Steimke, J.

    2011-02-01

    This report satisfies the initial phase of Task WP-2.3.4 Alternative Sodium Recovery Technology, Subtask 1; Develop Near-Tank Nitrate/Nitrite Destruction Technology. Some of the more common anions in carbon steel waste tanks at SRS and Hanford Site are nitrate which is corrosive, and nitrite and hydroxide which are corrosion inhibitors. At present it is necessary to periodically add large quantities of 50 wt% caustic to waste tanks. There are three primary reasons for this addition. First, when the contents of salt tanks are dissolved, sodium hydroxide preferentially dissolves and is removed. During the dissolution process the concentration of free hydroxide in the tank liquid can decrease from 9 M to less than 0.2 M. As a result, roughly half way through the dissolution process large quantities of sodium hydroxide must be added to the tank to comply with requirements for corrosion control. Second, hydroxide is continuously consumed by reaction with carbon dioxide which occurs naturally in purge air used to prevent buildup of hydrogen gas inside the tanks. The hydrogen is generated by radiolysis of water. Third, increasing the concentration of hydroxide increases solubility of some aluminum compounds, which is desirable in processing waste. A process that converts nitrate and nitrite to hydroxide would reduce certain costs. (1) Less caustic would be purchased. (2) Some of the aluminum solid compounds in the waste tanks would become more soluble so less mass of solids would be sent to High Level Vitrification and therefore it would be not be necessary to make as much expensive high level vitrified product. (3) Less mass of sodium would be fed to Saltstone at SRS or Low Level Vitrification at Hanford Site so it would not be necessary to make as much low level product. (4) At SRS less nitrite and nitrate would be sent to Defense Waste Processing Facility (DWPF) so less formic acid would be consumed there and less hydrogen gas would be generated. This task involves literature survey of technologies to perform the nitrate to hydroxide conversion, selection of the most promising technologies, preparation of a flowsheet and design of a system. The most promising technologies are electrochemical reduction of nitrates and chemical reduction with hydrogen or ammonia. The primary reviewed technologies are listed and they aredescribed in more detail later in the report: (1) Electrochemical destruction; (2) Chemical reduction with agents such as ammonia, hydrazine or hydrogen; (3) Hydrothermal reduction process; and (4) Calcination. Only three of the technologies on the list have been demonstrated to generate usable amounts of caustic; electrochemical reduction and chemical reduction with ammonia, hydrazine or hydrogen and hydrothermal reduction. Chemical reduction with an organic reactant such as formic acid generates carbon dioxide which reacts with caustic and is thus counterproductive. Treatment of nitrate with aluminum or other active metals generates a solid product. High temperature calcination has the potential to generate sodium oxide which may be hydrated to sodium hydroxide, but this is unproven. The following criteria were developed to evaluate the most suitable option. The numbers in brackets after the criteria are relative weighting factors to account for importance: (1) Personnel exposure to radiation for installation, routine operation and maintenance; (2) Non-radioactive safety issues; (3) Whether the technology generates caustic and how many moles of caustic are generated per mole of nitrate plus nitrite decomposed; (4) Whether the technology can handle nitrate and nitrite at the concentrations encountered in waste; (5) Maturity of technology; (6) Estimated annual cost of operation (labor, depreciation, materials, utilities); (7) Capital cost; (8) Selectivity to nitrogen as decomposition product (other products are flammable and/or toxic); (9) Impact of introduced species; (10) Selectivity for destruction of nitrate vs. nitrite; and (11) Cost of deactivation and demolition. Each technology was given a score from one

  5. Transferring 2001 National Household Travel Survey

    SciTech Connect (OSTI)

    Hu, Patricia S; Reuscher, Tim; Schmoyer, Richard L; Chin, Shih-Miao

    2007-05-01

    Policy makers rely on transportation statistics, including data on personal travel behavior, to formulate strategic transportation policies, and to improve the safety and efficiency of the U.S. transportation system. Data on personal travel trends are needed to examine the reliability, efficiency, capacity, and flexibility of the Nation's transportation system to meet current demands and to accommodate future demand. These data are also needed to assess the feasibility and efficiency of alternative congestion-mitigating technologies (e.g., high-speed rail, magnetically levitated trains, and intelligent vehicle and highway systems); to evaluate the merits of alternative transportation investment programs; and to assess the energy-use and air-quality impacts of various policies. To address these data needs, the U.S. Department of Transportation (USDOT) initiated an effort in 1969 to collect detailed data on personal travel. The 1969 survey was the first Nationwide Personal Transportation Survey (NPTS). The survey was conducted again in 1977, 1983, 1990, 1995, and 2001. Data on daily travel were collected in 1969, 1977, 1983, 1990 and 1995. In 2001, the survey was renamed the National Household Travel Survey (NHTS) and it collected both daily and long-distance trips. The 2001 survey was sponsored by three USDOT agencies: Federal Highway Administration (FHWA), Bureau of Transportation Statistics (BTS), and National Highway Traffic Safety Administration (NHTSA). The primary objective of the survey was to collect trip-based data on the nature and characteristics of personal travel so that the relationships between the characteristics of personal travel and the demographics of the traveler can be established. Commercial and institutional travel were not part of the survey. Due to the survey's design, data in the NHTS survey series were not recommended for estimating travel statistics for categories smaller than the combination of Census division (e.g., New England, Middle Atlantic, and Pacific), MSA size, and the availability of rail. Extrapolating NHTS data within small geographic areas could risk developing and subsequently using unreliable estimates. For example, if a planning agency in City X of State Y estimates travel rates and other travel characteristics based on survey data collected from NHTS sample households that were located in City X of State Y, then the agency could risk developing and using unreliable estimates for their planning process. Typically, this limitation significantly increases as the size of an area decreases. That said, the NHTS contains a wealth of information that could allow statistical inferences about small geographic areas, with a pre-determined level of statistical certainty. The question then becomes whether a method can be developed that integrates the NHTS data and other data to estimate key travel characteristics for small geographic areas such as Census tract and transportation analysis zone, and whether this method can outperform other, competing methods.

  6. Energy conservation by hyperfiltration: food industry background literature survey

    SciTech Connect (OSTI)

    Not Available

    1980-04-15

    The application of hyperfiltration to selected food product streams and food processing wastewaters for energy conservation was examined. This literature survey had led to the following conclusions: no research has been conducted in the food industry using membranes with hot process streams due to the temperature limitation (< 40/sup 0/C) of the typically studied cellulose acetate membranes; based on the bench-scale research reviewed, concentration of fruit and vegetable juices with membranes appears to be technically feasible; pretreatment and product recovery research was conducted with membranes on citrus peel oil, potato processing and brine wastewaters and wheys. The experiments demonstrated that these applications are feasible; many of the problems that have been identified with membranes are associated with either the suspended solids or the high osmotic pressure and viscosity of many foods; research using dynamic membranes has been conducted with various effluents, at temperatures to approx. 100/sup 0/C, at pressures to 1200 psi and with suspended solids to approx. 2%; and, the dynamic membrane is being prototype tested by NASA for high temperature processing of shower water. The literature review substantiates potential for dynamic membrane on porous stainless tubes to process a number of hot process and effluent streams in the food processing industry. Hot water for recycle and product concentrations are major areas with potential for economic application. The two plants involved in the first phase of the project should be reviewed to identify potential energy conservation applications. As many as possible of the conservation applications should be tested during the screening phase at each site. The most promising applications at each site should be evaluated more intensively to establish engineering estimates of the economics of this technology for the canned fruit and vegetable segment of the food industry.

  7. Research Initiative Will Demonstrate Low Temperature Geothermal...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Research Initiative Will Demonstrate Low Temperature Geothermal Electrical Power Generation Systems Using Oilfield Fluids Research Initiative Will Demonstrate Low Temperature ...

  8. Aqua Farms International Aquaculture Low Temperature Geothermal...

    Open Energy Info (EERE)

    Farms International Aquaculture Low Temperature Geothermal Facility Jump to: navigation, search Name Aqua Farms International Aquaculture Low Temperature Geothermal Facility...

  9. Flint Greenhouses Greenhouse Low Temperature Geothermal Facility...

    Open Energy Info (EERE)

    Greenhouses Greenhouse Low Temperature Geothermal Facility Jump to: navigation, search Name Flint Greenhouses Greenhouse Low Temperature Geothermal Facility Facility Flint...

  10. Sunnybrook Farms Aquaculture Low Temperature Geothermal Facility...

    Open Energy Info (EERE)

    Sunnybrook Farms Aquaculture Low Temperature Geothermal Facility Jump to: navigation, search Name Sunnybrook Farms Aquaculture Low Temperature Geothermal Facility Facility...

  11. Bigfork Greenhouses Greenhouse Low Temperature Geothermal Facility...

    Open Energy Info (EERE)

    Bigfork Greenhouses Greenhouse Low Temperature Geothermal Facility Jump to: navigation, search Name Bigfork Greenhouses Greenhouse Low Temperature Geothermal Facility Facility...

  12. Crook's Greenhouse Greenhouse Low Temperature Geothermal Facility...

    Open Energy Info (EERE)

    Crook's Greenhouse Greenhouse Low Temperature Geothermal Facility Jump to: navigation, search Name Crook's Greenhouse Greenhouse Low Temperature Geothermal Facility Facility...

  13. Duckwater Aquaculture Low Temperature Geothermal Facility | Open...

    Open Energy Info (EERE)

    Duckwater Aquaculture Low Temperature Geothermal Facility Jump to: navigation, search Name Duckwater Aquaculture Low Temperature Geothermal Facility Facility Duckwater Sector...

  14. Castlevalley Greenhouses Greenhouse Low Temperature Geothermal...

    Open Energy Info (EERE)

    Castlevalley Greenhouses Greenhouse Low Temperature Geothermal Facility Jump to: navigation, search Name Castlevalley Greenhouses Greenhouse Low Temperature Geothermal Facility...

  15. Jackson Greenhouses Greenhouse Low Temperature Geothermal Facility...

    Open Energy Info (EERE)

    Greenhouse Low Temperature Geothermal Facility Jump to: navigation, search Name Jackson Greenhouses Greenhouse Low Temperature Geothermal Facility Facility Jackson...

  16. Fish Producers Aquaculture Low Temperature Geothermal Facility...

    Open Energy Info (EERE)

    Aquaculture Low Temperature Geothermal Facility Jump to: navigation, search Name Fish Producers Aquaculture Low Temperature Geothermal Facility Facility Fish Producers...

  17. Method for measuring surface temperature

    DOE Patents [OSTI]

    Baker, Gary A.; Baker, Sheila N.; McCleskey, T. Mark

    2009-07-28

    The present invention relates to a method for measuring a surface temperature using is a fluorescent temperature sensor or optical thermometer. The sensor includes a solution of 1,3-bis(1-pyrenyl)propane within a 1-butyl-1-1-methyl pyrrolidinium bis(trifluoromethylsulfonyl)imide ionic liquid solvent. The 1,3-bis(1-pyrenyl)propane remains unassociated when in the ground state while in solution. When subjected to UV light, an excited state is produced that exists in equilibrium with an excimer. The position of the equilibrium between the two excited states is temperature dependent.

  18. The Dark Energy Survey Data Management System

    SciTech Connect (OSTI)

    Mohr, Joseph J.; Barkhouse, Wayne; Beldica, Cristina; Bertin, Emmanuel; Dora Cai, Y.; Nicolaci da Costa, Luiz A.; Darnell, J.Anthony; Daues, Gregory E.; Jarvis, Michael; Gower, Michelle; Lin, Huan; /Fermilab /Rio de Janeiro Observ.

    2008-07-01

    The Dark Energy Survey (DES) collaboration will study cosmic acceleration with a 5000 deg2 griZY survey in the southern sky over 525 nights from 2011-2016. The DES data management (DESDM) system will be used to process and archive these data and the resulting science ready data products. The DESDM system consists of an integrated archive, a processing framework, an ensemble of astronomy codes and a data access framework. We are developing the DESDM system for operation in the high performance computing (HPC) environments at the National Center for Supercomputing Applications (NCSA) and Fermilab. Operating the DESDM system in an HPC environment offers both speed and flexibility. We will employ it for our regular nightly processing needs, and for more compute-intensive tasks such as large scale image coaddition campaigns, extraction of weak lensing shear from the full survey dataset, and massive seasonal reprocessing of the DES data. Data products will be available to the Collaboration and later to the public through a virtual-observatory compatible web portal. Our approach leverages investments in publicly available HPC systems, greatly reducing hardware and maintenance costs to the project, which must deploy and maintain only the storage, database platforms and orchestration and web portal nodes that are specific to DESDM. In Fall 2007, we tested the current DESDM system on both simulated and real survey data. We used TeraGrid to process 10 simulated DES nights (3TB of raw data), ingesting and calibrating approximately 250 million objects into the DES Archive database. We also used DESDM to process and calibrate over 50 nights of survey data acquired with the Mosaic2 camera. Comparison to truth tables in the case of the simulated data and internal crosschecks in the case of the real data indicate that astrometric and photometric data quality is excellent.

  19. A Survey of lamba Repressor Fragments from Two-State to to Downhill Folding

    SciTech Connect (OSTI)

    Liu, F.; Gao, Y; Gruebele, M

    2010-01-01

    We survey the two-state to downhill folding transition by examining 20 {lambda}{sub 6-85}* mutants that cover a wide range of stabilities and folding rates. We investigated four new {lambda}{sub 6-85}* mutants designed to fold especially rapidly. Two were engineered using the core remodeling of Lim and Sauer, and two were engineered using Ferreiro et al.'s frustratometer. These proteins have probe-dependent melting temperatures as high as 80 C and exhibit a fast molecular phase with the characteristic temperature dependence of the amplitude expected for downhill folding. The survey reveals a correlation between melting temperature and downhill folding previously observed for the {beta}-sheet protein WW domain. A simple model explains this correlation and predicts the melting temperature at which downhill folding becomes possible. An X-ray crystal structure with a 1.64-{angstrom} resolution of a fast-folding mutant fragment shows regions of enhanced rigidity compared to the full wild-type protein.

  20. High temperature structural insulating material

    DOE Patents [OSTI]

    Chen, W.Y.

    1984-07-27

    A high temperature structural insulating material useful as a liner for cylinders of high temperature engines through the favorable combination of high service temperature (above about 800/sup 0/C), low thermal conductivity (below about 0.2 W/m/sup 0/C), and high compressive strength (above about 250 psi). The insulating material is produced by selecting hollow ceramic beads with a softening temperature above about 800/sup 0/C, a diameter within the range of 20-200 ..mu..m, and a wall thickness in the range of about 2 to 4 ..mu..m; compacting the beads and a compatible silicate binder composition under pressure and sintering conditions to provide the desired structural form with the structure having a closed-cell, compact array of bonded beads.

  1. High temperature structural insulating material

    DOE Patents [OSTI]

    Chen, Wayne Y.

    1987-01-01

    A high temperature structural insulating material useful as a liner for cylinders of high temperature engines through the favorable combination of high service temperature (above about 800.degree. C.), low thermal conductivity (below about 0.2 W/m.degree. C.), and high compressive strength (above about 250 psi). The insulating material is produced by selecting hollow ceramic beads with a softening temperature above about 800.degree. C., a diameter within the range of 20-200 .mu.m, and a wall thickness in the range of about 2-4 .mu.m; compacting the beads and a compatible silicate binder composition under pressure and sintering conditions to provide the desired structural form with the structure having a closed-cell, compact array of bonded beads.

  2. Moderate Temperature | Open Energy Information

    Open Energy Info (EERE)

    temperature level. Thus, reservoirs in the 190 to 230C range should have liquid water as the mobile fluid phase, and as such, this class is reasonably well constrained....

  3. Investigating the Effects of Temperature

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Investigating the Effects of Temperature on Power Output Objective: Students will use concepts learned in class to explore the many variables that effect the efficiency of solar panels in regards to power output. Materials: * PV Array or Solar Panel * 2 Multimeter * Frozen Ice Packs * Low Power DC Bulb * Halogen Lamp (500 Watts) * 4 or 5 Alligator clip wires * Timer Investigative Question: How does the power output change as the temperature of the PV system changes. Procedure: 1) Attach the

  4. High temperature current mirror amplifier

    DOE Patents [OSTI]

    Patterson, III, Raymond B.

    1984-05-22

    A high temperature current mirror amplifier having biasing means in the transdiode connection of the input transistor for producing a voltage to maintain the base-collector junction reversed-biased and a current means for maintaining a current through the biasing means at high temperatures so that the base-collector junction of the input transistor remained reversed-biased. For accuracy, a second current mirror is provided with a biasing means and current means on the input leg.

  5. Take the the Annual NERSC Survey - Closes January 31

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Take the the Annual NERSC Survey Take the the Annual NERSC Survey - Closes January 31 January 9, 2014 by Francesca Verdier User input on the annual NERSC survey is important to us. We use the survey to help us set priorities and to get a realistic view of which things are going well and which need more attention. Here is the link to the survey, which closes January 31: https://www.nersc.gov/news-publications/publications-reports/user-surveys/2013/ Subscribe via RSS Subscribe Browse by Date May

  6. Please take the 2012 NERSC Usr Survey (now closed)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Please take the 2012 NERSC Usr Survey Please take the 2012 NERSC Usr Survey (now closed) January 1, 2013 by Francesca Verdier Please take a few minutes to fill out NERSC's annual user survey. Your feedback is important because it allows us to judge the quality of our services, give DOE information on how we are doing, and point us to areas in which we can improve. The survey is on the web at the URL: https://www.nersc.gov/news-publications/publications-reports/user-surveys/2012/ The survey,

  7. Temperature sensors for OTEC applications

    SciTech Connect (OSTI)

    Seren, L.; Panchal, C.B.; Rote, D.M.

    1984-05-01

    Ocean thermal energy conversion (OTEC) applications require accurate measurement of temperatures in the 0 to 30/sup 0/C range. This report documents an experimental examination of commercially available quartz-crystal thermometers and thermistors. Three fixed-point baths were used for temperature measurements: the distilled-water/distilled-ice-water slurry, the triple-point-of-water cell, and the gallium melting-point cell. The temperature of carefully prepared ice-water slurries was verified routinely as 0.001 +- 0.003/sup 0/C. Quartz-crystal probes proved accurate to about 1 to 2 mK, with drift errors of the same order over a few days. Bead- and disk-type thermistor probes were found to be about equally stable with time in the 0 to 30/sup 0/C range. The overall probable error of using thermistors was found to be +-4 mK. A solid-block temperature bath suitable for on-site calibrations in OTEC work was used in the temperature-sweeping mode. Various polynomial fits were examined for the purpose of thermistor calibration; fits of order two and higher yielded about equally accurate calculated temperatures.

  8. High temperature thermometric phosphors for use in a temperature sensor

    DOE Patents [OSTI]

    Allison, S.W.; Cates, M.R.; Boatner, L.A.; Gillies, G.T.

    1998-03-24

    A high temperature phosphor consists essentially of a material having the general formula LuPO{sub 4}:Dy{sub (x)},Eu{sub (y)}, wherein: 0.1 wt %{<=}x{<=}20 wt % and 0.1 wt %{<=}y{<=}20 wt %. The high temperature phosphor is in contact with an article whose temperature is to be determined. The article having the phosphor in contact with it is placed in the environment for which the temperature of the article is to be determined. The phosphor is excited by a laser causing the phosphor to fluoresce. The emission from the phosphor is optically focused into a beam-splitting mirror which separates the emission into two separate emissions, the emission caused by the dysprosium dopant and the emission caused by the europium dopant. The separated emissions are optically filtered and the intensities of the emission are detected and measured. The ratio of the intensity of each emission is determined and the temperature of the article is calculated from the ratio of the intensities of the separate emissions. 2 figs.

  9. High temperature thermometric phosphors for use in a temperature sensor

    DOE Patents [OSTI]

    Allison, Stephen W.; Cates, Michael R.; Boatner, Lynn A.; Gillies, George T.

    1998-01-01

    A high temperature phosphor consists essentially of a material having the general formula LuPO.sub.4 :Dy.sub.(x),Eu.sub.(y), wherein: 0.1 wt %.ltoreq.x.ltoreq.20 wt % and 0.1 wt %.ltoreq.y.ltoreq.20 wt %. The high temperature phosphor is in contact with an article whose temperature is to be determined. The article having the phosphor in contact with it is placed in the environment for which the temperature of the article is to be determined. The phosphor is excited by a laser causing the phosphor to fluoresce. The emission from the phosphor is optically focused into a beam-splitting mirror which separates the emission into two separate emissions, the emission caused by the dysprosium dopant and the emission caused by the europium dopent. The separated emissions are optically filtered and the intensities of the emission are detected and measured. The ratio of the intensity of each emission is determined and the temperature of the article is calculated from the ratio of the intensities of the separate emissions.

  10. Dark energy properties from large future galaxy surveys

    SciTech Connect (OSTI)

    Basse, Tobias; Bjlde, Ole Eggers; Hannestad, Steen; Hamann, Jan; Wong, Yvonne Y.Y. E-mail: oeb@phys.au.dk E-mail: sth@phys.au.dk

    2014-05-01

    We perform a detailed forecast on how well a Euclid-like survey will be able to constrain dark energy and neutrino parameters from a combination of its cosmic shear power spectrum, galaxy power spectrum, and cluster mass function measurements. We find that the combination of these three probes vastly improves the survey's potential to measure the time evolution of dark energy. In terms of a dark energy figure-of-merit defined as (?(w{sub p})?(w{sub a})){sup ?1}, we find a value of 690 for Euclid-like data combined with Planck-like measurements of the cosmic microwave background anisotropies in a 10-dimensional cosmological parameter space, assuming a ?CDM fiducial cosmology. For the more commonly used 7-parameter model, we find a figure-of-merit of 1900 for the same data combination. We consider also the survey's potential to measure dark energy perturbations in models wherein the dark energy is parameterised as a fluid with a nonstandard non-adiabatic sound speed, and find that in an optimistic scenario in which w{sub 0} deviates from -1 by as much as is currently observationally allowed, models with c-circumflex {sub s}{sup 2} = 10{sup ?6} and c-circumflex {sub s}{sup 2} = 1 can be distinguished from one another at more than 2? significance. We emphasise that constraints on the dark energy sound speed from cluster measurements are strongly dependent on the modelling of the cluster mass function; significantly weaker sensitivities ensue if we modify our model to include fewer features of nonlinear dark energy clustering. Finally, we find that the sum of neutrino masses can be measured with a 1? precision of 0.015 eV, even in complex cosmological models in which the dark energy equation of state varies with time. The 1? sensitivity to the effective number of relativistic species N{sub eff}{sup ml} is approximately 0.03, meaning that the small deviation of 0.046 from 3 in the standard value of N{sub eff}{sup ml} due to non-instantaneous decoupling and finite temperature effects can be probed with 1? precision for the first time.

  11. Apparatus and method for high temperature viscosity and temperature measurements

    DOE Patents [OSTI]

    Balasubramaniam, Krishnan; Shah, Vimal; Costley, R. Daniel; Singh, Jagdish P.

    2001-01-01

    A probe for measuring the viscosity and/or temperature of high temperature liquids, such as molten metals, glass and similar materials comprises a rod which is an acoustical waveguide through which a transducer emits an ultrasonic signal through one end of the probe, and which is reflected from (a) a notch or slit or an interface between two materials of the probe and (b) from the other end of the probe which is in contact with the hot liquid or hot melt, and is detected by the same transducer at the signal emission end. To avoid the harmful effects of introducing a thermally conductive heat sink into the melt, the probe is made of relatively thermally insulative (non-heat-conductive) refractory material. The time between signal emission and reflection, and the amplitude of reflections, are compared against calibration curves to obtain temperature and viscosity values.

  12. Utility FGD survey, January--December 1988

    SciTech Connect (OSTI)

    Hance, S.L.; McKibben, R.S.; Jones, F.M. )

    1991-09-01

    The Utility FGD Survey report, which is generated by a computerized data base management system, represents a survey of operational and planned domestic utility flue gas desulfurization (FGD) systems. It summarizes information contributed by the utility industry, system and equipment suppliers, system designers, research organizations, and regulatory agencies. The data cover system design, fuel characteristics, operating history, and actual system performance. Also included is a unit-by-unit discussion of problems and solutions associated with the boilers, scrubbers, and FGD systems. The development status (operational, under construction, or in the planning stages), system supplier, process, waste disposal practice, and regulatory class are tabulated alphabetically by utility company. Simplified process flow diagrams of FGD systems, definitions, and a glossary of terms are attached to the report. Current data for domestic FGD systems show systems in operation, systems under construction, and systems planned. The current total FGD-controlled capacity in the United States is 67,091 MW.

  13. A survey of numerical cubature over triangles

    SciTech Connect (OSTI)

    Lyness, J.N.; Cools, R.

    1993-12-31

    This survey collects together theoretical results in the area of numerical cubature over triangles and is a vehicle for a current bibliography. We treat first the theory relating to regular integrands and then the corresponding theory for singular integrands with emphasis on the ``full comer singularity.`` Within these two sections we treat successively approaches based on transforming the triangle into a square, formulas based on polynomial moment fitting, and extrapolation techniques. Within each category we quote key theoretical results without proof, and relate other results and references to these. Nearly all the references we have found may be readily placed in one of these categories. This survey is theoretical in character and does not include recent work in adaptive and automatic integration.

  14. Low to moderate temperature nanolaminate heater

    DOE Patents [OSTI]

    Eckels, J. Del; Nunes, Peter J.; Simpson, Randall L.; Hau-Riege, Stefan; Walton, Chris; Carter, J. Chance; Reynolds, John G.

    2011-01-11

    A low to moderate temperature heat source comprising a high temperature energy source modified to output low to moderate temperatures wherein the high temperature energy source modified to output low to moderate temperatures is positioned between two thin pieces to form a close contact sheath. In one embodiment the high temperature energy source modified to output low to moderate temperatures is a nanolaminate multilayer foil of reactive materials that produces a heating level of less than 200.degree. C.

  15. 2009 Annual Employee Survey Results for

    Energy Savers [EERE]

    9 Annual Employee Survey Results for Department of Energy All Respondents 1) Interpretation of Results: The agency's overall results were favorable and showed the agency improving in most areas. The agency remained strong in areas pertaining to Job Satisfaction and Talent Management. The agency's biggest challenge is in Performance Culture. This is an area that the agency has been working on for several years and will continue to do so in 2010. Scores related to Leadership/Supervisory dimension

  16. Office of Survey Development and Statistical Integration

    U.S. Energy Information Administration (EIA) Indexed Site

    Steve Harvey April 27, 2011 | Washington, D.C. Tough Choices in U.S. EIA's Data Programs Agenda * Office of Oil, Gas, and Coal Supply Statistics * Office of Petroleum and Biofuels Statistics * Office of Electricity, Renewables, and Uranium Statistics * Office of Energy Consumption and Efficiency Statistics * Office of Survey Development and Statistical Integration 2 Presenter name, Presentation location, Presentation date Coal Data Collection Program 3 James Kendell Washington, DC, April 27,

  17. Aeromagnetic Survey At Chena Geothermal Area (Kolker, 2008) ...

    Open Energy Info (EERE)

    Phase I) Notes Fugro, Inc. performed an airborne geophysical survey using the DIGHEM (Digital Helicopter ElectroMagnetics) aircraft over a 937 km2 survey grid. Total field, nT...

  18. Table 2. Percent of Households with Vehicles, Selected Survey...

    U.S. Energy Information Administration (EIA) Indexed Site

    Percent of Households with Vehicles, Selected Survey Years " ,"Survey Years" ,1983,1985,1988,1991,1994,2001 "Total",85.5450237,89.00343643,88.75545852,89.42917548,87.25590956,92.08...

  19. Ground Gravity Survey At Neal Hot Springs Geothermal Area (U...

    Open Energy Info (EERE)

    survey was completed by MWH Geo-Surveys. Interpretations were made by creating a 3D density inversion map. Gravity and magnetic data were used in siting the first production...

  20. The Sloan Digital Sky Survey Quasar Lens Search. IV. Statistical...

    Office of Scientific and Technical Information (OSTI)

    The Sloan Digital Sky Survey Quasar Lens Search. IV. Statistical Lens Sample from the Fifth Data Release Citation Details In-Document Search Title: The Sloan Digital Sky Survey...

  1. Findings from Survey Administered to Weatherization Training Centers

    SciTech Connect (OSTI)

    Conlon, Brian; Tonn, Bruce Edward

    2015-03-01

    This report summarizes results of a survey administered to directors of weatherization training centers that receive funding from the U.S. Department of Energy. The survey presents results related to questions on training offered and future plans.

  2. Vehicle Technologies Office: Workplace Charging Challenge 2015 Annual Survey Webinar

    Broader source: Energy.gov [DOE]

    This webinar provides an update on the Workplace Charging Challenge initiative, describes the survey, discusses why the Survey input is essential, and walks through the log-in and submission process.

  3. Report of Survey of Oak Ridge Isotope Enrichment (Calutron) Facility...

    Office of Environmental Management (EM)

    Report of Survey of Oak Ridge Isotope Enrichment (Calutron) Facility Building 9204-3 Report of Survey of Oak Ridge Isotope Enrichment (Calutron) Facility Building 9204-3 The ...

  4. Category:2-M Probe Survey | Open Energy Information

    Open Energy Info (EERE)

    2-M Probe Survey Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Geothermalpower.jpg Looking for the 2-M Probe Survey page? For detailed information on 2-M Probe...

  5. "Table 11. Fuel Economy, Selected Survey Years (Miles Per Gallon...

    U.S. Energy Information Administration (EIA) Indexed Site

    Fuel Economy, Selected Survey Years (Miles Per Gallon)" ,"Survey Years" ,1983,1985,1988,1991,1994,2001 "Total",15.1,16.1,18.3,19.3,19.8,20.2 "Household Characteristics" "Census...

  6. Autonomous mobile robot for radiologic surveys

    DOE Patents [OSTI]

    Dudar, A.M.; Wagner, D.G.; Teese, G.D.

    1994-06-28

    An apparatus is described for conducting radiologic surveys. The apparatus comprises in the main a robot capable of following a preprogrammed path through an area, a radiation monitor adapted to receive input from a radiation detector assembly, ultrasonic transducers for navigation and collision avoidance, and an on-board computer system including an integrator for interfacing the radiation monitor and the robot. Front and rear bumpers are attached to the robot by bumper mounts. The robot may be equipped with memory boards for the collection and storage of radiation survey information. The on-board computer system is connected to a remote host computer via a UHF radio link. The apparatus is powered by a rechargeable 24-volt DC battery, and is stored at a docking station when not in use and/or for recharging. A remote host computer contains a stored database defining paths between points in the area where the robot is to operate, including but not limited to the locations of walls, doors, stationary furniture and equipment, and sonic markers if used. When a program consisting of a series of paths is downloaded to the on-board computer system, the robot conducts a floor survey autonomously at any preselected rate. When the radiation monitor detects contamination, the robot resurveys the area at reduced speed and resumes its preprogrammed path if the contamination is not confirmed. If the contamination is confirmed, the robot stops and sounds an alarm. 5 figures.

  7. Autonomous mobile robot for radiologic surveys

    DOE Patents [OSTI]

    Dudar, Aed M.; Wagner, David G.; Teese, Gregory D.

    1994-01-01

    An apparatus for conducting radiologic surveys. The apparatus comprises in the main a robot capable of following a preprogrammed path through an area, a radiation monitor adapted to receive input from a radiation detector assembly, ultrasonic transducers for navigation and collision avoidance, and an on-board computer system including an integrator for interfacing the radiation monitor and the robot. Front and rear bumpers are attached to the robot by bumper mounts. The robot may be equipped with memory boards for the collection and storage of radiation survey information. The on-board computer system is connected to a remote host computer via a UHF radio link. The apparatus is powered by a rechargeable 24-volt DC battery, and is stored at a docking station when not in use and/or for recharging. A remote host computer contains a stored database defining paths between points in the area where the robot is to operate, including but not limited to the locations of walls, doors, stationary furniture and equipment, and sonic markers if used. When a program consisting of a series of paths is downloaded to the on-board computer system, the robot conducts a floor survey autonomously at any preselected rate. When the radiation monitor detects contamination, the robot resurveys the area at reduced speed and resumes its preprogrammed path if the contamination is not confirmed. If the contamination is confirmed, the robot stops and sounds an alarm.

  8. The Dark Energy Survey Camera (DECam)

    SciTech Connect (OSTI)

    Diehl, H.Thomas; /Fermilab

    2011-09-09

    The Dark Energy Survey (DES) is a next generation optical survey aimed at understanding the expansion rate of the Universe using four complementary methods: weak gravitational lensing, galaxy cluster counts, baryon acoustic oscillations, and Type Ia supernovae. To perform the survey, the DES Collaboration is building the Dark Energy Camera (DECam), a 3 square degree, 570 Megapixel CCD camera that will be mounted at the prime focus of the Blanco 4-meter telescope at the Cerro Tololo Inter-American Observatory. CCD production has finished, yielding roughly twice the required 62 2k x 4k detectors. The construction of DECam is nearly finished. Integration and commissioning on a 'telescope simulator' of the major hardware and software components, except for the optics, recently concluded at Fermilab. Final assembly of the optical corrector has started at University College, London. Some components have already been received at CTIO. 'First-light' will be sometime in 2012. This oral presentation concentrates on the technical challenges involved in building DECam (and how we overcame them), and the present status of the instrument.

  9. The FIRST-2MASS Red Quasar Survey

    SciTech Connect (OSTI)

    Glikman, E; Helfand, D J; White, R L; Becker, R H; Gregg, M D; Lacy, M

    2007-06-28

    Combining radio observations with optical and infrared color selection--demonstrated in our pilot study to be an efficient selection algorithm for finding red quasars--we have obtained optical and infrared spectroscopy for 120 objects in a complete sample of 156 candidates from a sky area of 2716 square degrees. Consistent with our initial results, we find our selection criteria--J-K > 1.7,R-K > 4.0--yield a {approx} 50% success rate for discovering quasars substantially redder than those found in optical surveys. Comparison with UVX- and optical color-selected samples shows that {approx}> 10% of the quasars are missed in a magnitude-limited survey. Simultaneous two-frequency radio observations for part of the sample indicate that a synchrotron continuum component is ruled out as a significant contributor to reddening the quasars spectra. We go on to estimate extinctions for our objects assuming their red colors are caused by dust. Continuum fits and Balmer decrements suggest E(B-V) values ranging from near zero to 2.5 magnitudes. Correcting the K-band magnitudes for these extinctions, we find that for K {le} 14.0, red quasars make up between 25% and 60% of the underlying quasar population; owing to the incompleteness of the 2MASS survey at fainter K-band magnitudes, we can only set a lower limit to the radio-detected red quasar population of > 20-30%.

  10. Commercial Buildings Energy Consumption Survey (CBECS) - U.S...

    Gasoline and Diesel Fuel Update (EIA)

    Consumption & Efficiency Commercial Buildings Energy Consumption Survey (CBECS) Glossary FAQS Overview Data 2012 2003 1999 1995 1992 Previous Analysis & Projections ...

  11. Web Survey Requirements and Best Practices | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    User Experience Research & Statistics » Web Survey Requirements and Best Practices Web Survey Requirements and Best Practices The Office of Energy Efficiency and Renewable Energy (EERE) considers surveys a useful way to gauge the opinions of your readers and learn more about your website's audiences, but you'll often need approval from the Office of Management and Budget (OMB) to run one. Developing a Survey First, your team should decide what questions you will ask and how and where you

  12. 2010 - Federal Viewpoint Survey Reports | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    0 - Federal Viewpoint Survey Reports 2010 - Federal Viewpoint Survey Reports The 2010 Trend report provides summary results for the Department or Energy's portion of the Federal Employee Viewpoint Survey. The report also shows how the 2010 results compare to the results of previous years. PDF icon Department of Energy: 2010 Federal Employee Viewpoint Survey Trend Report Responsible Contacts Thomasina Mathews PROGRAM MANAGER E-mail thomasina.mathews@hq.doe.gov Phone 202-586-2657 More Documents

  13. 2011 - Federal Viewpoint Survey Reports | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1 - Federal Viewpoint Survey Reports 2011 - Federal Viewpoint Survey Reports The following highlight report focuses on the Department of Energy's areas of strengths and challenges, identifies areas of progress and opportunities for improvement. The Departments 2011 results are compared with both the 2011 Governmentwide results and our 2010 survey results. The Trend report provides summary results for the Department or Energy's portion of the Federal Employee Viewpoint Survey. The report also

  14. 2012 - Federal Viewpoint Survey Reports | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    2 - Federal Viewpoint Survey Reports 2012 - Federal Viewpoint Survey Reports The following highlight report focuses on the Department of Energy's areas of strengths and challenges, identifies areas of progress and opportunities for improvement. The Departments 2012 results are compared with both the 2012 Government wide results and our 2011 survey results. PDF icon 2012 Federal Employee Viewpoint Survey Results: Agency Management Report Responsible Contacts Thomasina Mathews PROGRAM MANAGER

  15. 2012 Independent Communication and Outreach Stakeholder Satisfaction Survey

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy 2 Independent Communication and Outreach Stakeholder Satisfaction Survey 2012 Independent Communication and Outreach Stakeholder Satisfaction Survey DOE-LM periodically surveys its stakeholders to collect their feedback on DOE-LM performance at both a local and national level. The first customer satisfaction survey was conducted in 2005 and focused primarily on DOE-LM's "business lines": records management; site management; personal/real property; and

  16. Aeromagnetic Survey At Raft River Geothermal Area (1981) | Open...

    Open Energy Info (EERE)

    search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Aeromagnetic Survey At Raft River Geothermal Area (1981) Exploration Activity Details Location Raft River...

  17. Aeromagnetic Survey At Raft River Geothermal Area (1978) | Open...

    Open Energy Info (EERE)

    search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Aeromagnetic Survey At Raft River Geothermal Area (1978) Exploration Activity Details Location Raft River...

  18. POLICY GUIDANCE MEMORANDUM #16 OPM Managers' Satisfaction Survey |

    Energy Savers [EERE]

    Department of Energy 6 OPM Managers' Satisfaction Survey POLICY GUIDANCE MEMORANDUM #16 OPM Managers' Satisfaction Survey This memorandum provides guidance on how to implement the requirement for hiring managers to complete the OPM Managers' Satisfaction Survey before Servicing Human Resources Offices (SHROs) can make an official offer to any job selectee. PDF icon POLICY GUIDANCE MEMORANDUM #16 OPM Managers' Satisfaction Survey Responsible Contacts Jennifer Ackerman Director, Human Capital

  19. Aeromagnetic Survey At Blue Mountain Geothermal Area (Fairbank...

    Open Energy Info (EERE)

    Mountain Geothermal Area (Fairbank Engineering Ltd, 2003) Exploration Activity Details Location Blue Mountain Geothermal Area Exploration Technique Aeromagnetic Survey Activity...

  20. DOE Initiative to Improve PM and EVM, Integration Survey Results |

    Energy Savers [EERE]

    Department of Energy Initiative to Improve PM and EVM, Integration Survey Results DOE Initiative to Improve PM and EVM, Integration Survey Results DOE Initiative to Improve PM and EVM, Integration Survey Results Karen Urschel, Humphreys & Associates March 24, 2016 PDF icon Presentation More Documents & Publications Department of Energy Earned Value Management Survey Results Recommendations to Improve EVM and Project Management Integration in the DOE Microsoft PowerPoint - 07 Raines

  1. Aeromagnetic Survey At Coso Geothermal Area (1977) | Open Energy...

    Open Energy Info (EERE)

    Home Exploration Activity: Aeromagnetic Survey At Coso Geothermal Area (1977) Exploration Activity Details Location Coso Geothermal Area Exploration Technique...

  2. 2015 Readers' Survey: Tell us what you think!

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2015 Readers' Survey Community Connections: Your link to news and opportunities from Los Alamos National Laboratory Latest Issue:May 2016 all issues All Issues » submit 2015 Readers' Survey: Tell us what you think! Your feedback matters June 1, 2015 You can help shape this publication by taking a quick survey between now and June 19. You can help shape this publication by taking a quick survey between now and June 19. Contact Community Programs Director (Acting) Carole Rutten Email Editor Ute

  3. Merging high resolution geophysical and geochemical surveys to reduce exploration risk at glass buttes, Oregon

    SciTech Connect (OSTI)

    Walsh, Patrick; Fercho, Steven; Perkin, Doug; Martini, Brigette; Boshmann, Darrick

    2015-06-01

    The engineering and studies phase of the Glass Buttes project was aimed at reducing risk during the early stages of geothermal project development. The project’s inclusion of high resolution geophysical and geochemical surveys allowed Ormat to evaluate the value of these surveys both independently and in combination to quantify the most valuable course of action for exploration in an area where structure, permeability, and temperature are the most pressing questions. The sizes of the thermal anomalies at Glass Buttes are unusually large. Over the course of Phase I Ormat acquired high resolution LIDAR data to accurately map fault manifestations at the surface and collected detailed gravity and aeromagnetic surveys to map subsurface structural features. In addition, Ormat collected airborne hyperspectral data to assist with mapping the rock petrology and mineral alteration assemblages along Glass Buttes faults and magnetotelluric (MT) survey to try to better constrain the structures at depth. Direct and indirect identification of alteration assemblages reveal not only the geochemical character and temperature of the causative hydrothermal fluids but can also constrain areas of upflow along specific fault segments. All five datasets were merged along with subsurface lithologies and temperatures to predict the most likely locations for high permeability and hot fluids. The Glass Buttes temperature anomalies include 2 areas, totaling 60 km2 (23 mi2) of measured temperature gradients over 165° C/km (10° F/100ft). The Midnight Point temperature anomaly includes the Strat-1 well with 90°C (194 °F) at 603 m (1981 ft) with a 164 °C/km (10°F/100ft) temperature gradient at bottom hole and the GB-18 well with 71°C (160 °F) at 396 m (1300 ft) with a 182°C/km (11°F/100ft) gradient. The primary area of alteration and elevated temperature occurs near major fault intersections associated with Brothers Fault Zone and Basin and Range systems. Evidence for faulting is observed in each data set as follows. Field observations include fault plane orientations, complicated fault intersections, and hydrothermal alteration apparently pre-dating basalt flows. Geophysical anomalies include large, linear gradients in gravity and aeromagnetic data with magnetic lows possibly associated with alteration. Resistivity low anomalies also appear to have offsets associated with faulting. Hyperspectral and XRF identified alteration and individual volcanic flow units, respectively. When incorporated into a 3D geologic model, the fault intersections near the highest proven temperature and geophysical anomalies provide the first priority targets at Midnight Point. Ormat geologists selected the Midnight Point 52-33 drilling target based on a combination of pre-existing drilling data, geologic field work, geophysical interpretation, and geochemical analysis. Deep temperatures of well 52-33 was lower than anticipated. Temperature gradients in the well mirrored those found in historical drilling, but they decreased below 1500 ft and were isothermal below 2000 ft.

  4. Integrated Emissivity And Temperature Measurement

    DOE Patents [OSTI]

    Poulsen, Peter

    2005-11-08

    A multi-channel spectrometer and a light source are used to measure both the emitted and the reflected light from a surface which is at an elevated temperature relative to its environment. In a first method, the temperature of the surface and emissivity in each wavelength is calculated from a knowledge of the spectrum and the measurement of the incident and reflected light. In the second method, the reflected light is measured from a reference surface having a known reflectivity and the same geometry as the surface of interest and the emitted and the reflected light are measured for the surface of interest. These measurements permit the computation of the emissivity in each channel of the spectrometer and the temperature of the surface of interest.

  5. 2001 FEMP Customer Survey Report (Main Report) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Main Report) 2001 FEMP Customer Survey Report (Main Report) This summary presents the key findings and recommendations from the 2001 FEMP customer survey. The key findings presented in this summary are a condensed presentation of the more detailed findings presented in each of the chapters. PDF icon Study Report More Documents & Publications 2001 FEMP Customer Survey Report (Summary

  6. 2001 FEMP Customer Survey Report (Summary Report) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Summary Report) 2001 FEMP Customer Survey Report (Summary Report) The study was targeted to collect information from the average FEMP customer. As a result, the respondents in this survey represent 27 different federal agencies and a group of private contractors who have contracts with one or more federal agencies PDF icon Summary Report More Documents & Publications 2001 FEMP Customer Survey Report (Main

  7. Pacific Northwest residential energy survey. Volume 2. Technical appendix

    SciTech Connect (OSTI)

    1980-07-01

    The technical appendix presents the technical aspects of the Pacific Northwest Residential Energy Survey: the survey questionnaire, exhibit cards, instructions for interviewers, and a description of the survey plan. A description of the sample plan (method used to determine which 4000 households) is given. (MCW)

  8. Department of Energy: 2011 Federal Employee Viewpoint Survey Trend Report

    Energy Savers [EERE]

    Federal Employee Viewpoint Survey Page 1 of 23 ________________________________________________________________________________________________________________________________________________________________________________________________________________ Department of Energy 2011 Federal Employee Viewpoint Survey: Trend Report Response Summary Surveys Completed 2011 Governmentwide 266,376 2011 Department of Energy 5,613 2010 Department of Energy 6,648 2008 Department of Energy 6,093 2006

  9. Thermal disconnect for high-temperature batteries

    DOE Patents [OSTI]

    Jungst, Rudolph George; Armijo, James Rudolph; Frear, Darrel Richard

    2000-01-01

    A new type of high temperature thermal disconnect has been developed to protect electrical and mechanical equipment from damage caused by operation at extreme temperatures. These thermal disconnects allow continuous operation at temperatures ranging from 250.degree. C. to 450.degree. C., while rapidly terminating operation at temperatures 50.degree. C. to 150.degree. C. higher than the continuous operating temperature.

  10. Crystal face temperature determination means

    DOE Patents [OSTI]

    Nason, D.O.; Burger, A.

    1994-11-22

    An optically transparent furnace having a detection apparatus with a pedestal enclosed in an evacuated ampule for growing a crystal thereon is disclosed. Temperature differential is provided by a source heater, a base heater and a cold finger such that material migrates from a polycrystalline source material to grow the crystal. A quartz halogen lamp projects a collimated beam onto the crystal and a reflected beam is analyzed by a double monochromator and photomultiplier detection spectrometer and the detected peak position in the reflected energy spectrum of the reflected beam is interpreted to determine surface temperature of the crystal. 3 figs.

  11. High temperature superconductor current leads

    DOE Patents [OSTI]

    Hull, J.R.; Poeppel, R.B.

    1995-06-20

    An electrical lead is disclosed having one end for connection to an apparatus in a cryogenic environment and the other end for connection to an apparatus outside the cryogenic environment. The electrical lead includes a high temperature superconductor wire and an electrically conductive material distributed therein, where the conductive material is present at the one end of the lead at a concentration in the range of from 0 to about 3% by volume, and at the other end of the lead at a concentration of less than about 20% by volume. Various embodiments are shown for groups of high temperature superconductor wires and sheaths. 9 figs.

  12. High temperature superconductor current leads

    DOE Patents [OSTI]

    Hull, John R.; Poeppel, Roger B.

    1995-01-01

    An electrical lead having one end for connection to an apparatus in a cryogenic environment and the other end for connection to an apparatus outside the cryogenic environment. The electrical lead includes a high temperature superconductor wire and an electrically conductive material distributed therein, where the conductive material is present at the one end of the lead at a concentration in the range of from 0 to about 3% by volume, and at the other end of the lead at a concentration of less than about 20% by volume. Various embodiments are shown for groups of high temperature superconductor wires and sheaths.

  13. High temperature current mirror amplifier

    DOE Patents [OSTI]

    Patterson, R.B. III.

    1984-05-22

    Disclosed is a high temperature current mirror amplifier having biasing means in the transdiode connection of the input transistor for producing a voltage to maintain the base-collector junction reversed-biased and a current means for maintaining a current through the biasing means at high temperatures so that the base-collector junction of the input transistor remained reversed-biased. For accuracy, a second current mirror is provided with a biasing means and current means on the input leg. 2 figs.

  14. Bright microwave pulses from PSR B0531+21 observed with a prototype transient survey receiver

    SciTech Connect (OSTI)

    O'Dea, J. Andrew; Cheng, Tsan-Huei; Buu, Chau M.; Asmar, Sami W.; Armstrong, J. W.; Jenet, F. A.; Beroiz, Martin

    2014-05-01

    Recent discoveries of transient radio events have renewed interest in time-variable astrophysical phenomena. Many radio transient events are rare, requiring long observing times for reliable statistical study. The National Aeronautics and Space Administration/Jet Propulsion Laboratory's Deep Space Network (DSN) tracks spacecraft nearly continuously with 13 large-aperture, low system temperature radio antennas. During normal spacecraft operations, the DSN processes only a small fraction of the pre-detection bandwidth available from these antennas; any information in the remaining bandwidth, e.g., from an astronomical source in the same antenna beam as the spacecraft, is currently ignored. As a firmware modification to the standard DSN tracking receiver, we built a prototype receiver that could be used for astronomical transient surveys. Here, we demonstrate the receiver's utility through observations of bright pulses from the Crab pulsar and describe attributes of potential transient survey observations piggybacking on operational DSN tracks.

  15. PIA - Form EIA-475 A/G Residential Energy Consumption Survey...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Form EIA-475 AG Residential Energy Consumption Survey PIA - Form EIA-475 AG Residential Energy Consumption Survey PIA - Form EIA-475 AG Residential Energy Consumption Survey PDF ...

  16. High temperature two component explosive

    DOE Patents [OSTI]

    Mars, James E.; Poole, Donald R.; Schmidt, Eckart W.; Wang, Charles

    1981-01-01

    A two component, high temperature, thermally stable explosive composition comprises a liquid or low melting oxidizer and a liquid or low melting organic fuel. The oxidizer and fuel in admixture are incapable of substantial spontaneous exothermic reaction at temperatures on the order of 475.degree. K. At temperatures on the order of 475.degree. K., the oxidizer and fuel in admixture have an activation energy of at least about 40 kcal/mol. As a result of the high activation energy, the preferred explosive compositions are nondetonable as solids at ambient temperature, and become detonable only when heated beyond the melting point. Preferable oxidizers are selected from alkali or alkaline earth metal nitrates, nitrites, perchlorates, and/or mixtures thereof. Preferred fuels are organic compounds having polar hydrophilic groups. The most preferred fuels are guanidinium nitrate, acetamide and mixtures of the two. Most preferred oxidizers are eutectic mixtures of lithium nitrate, potassium nitrate and sodium nitrate, of sodium nitrite, sodium nitrate and potassium nitrate, and of potassium nitrate, calcium nitrate and sodium nitrate.

  17. High temperature electronic gain device

    DOE Patents [OSTI]

    McCormick, J. Byron; Depp, Steven W.; Hamilton, Douglas J.; Kerwin, William J.

    1979-01-01

    An integrated thermionic device suitable for use in high temperature, high radiation environments. Cathode and control electrodes are deposited on a first substrate facing an anode on a second substrate. The substrates are sealed to a refractory wall and evacuated to form an integrated triode vacuum tube.

  18. Catalysts for low temperature oxidation

    DOE Patents [OSTI]

    Toops, Todd J.; Parks, III, James E.; Bauer, John C.

    2016-03-01

    The invention provides a composite catalyst containing a first component and a second component. The first component contains nanosized gold particles. The second component contains nanosized platinum group metals. The composite catalyst is useful for catalyzing the oxidation of carbon monoxide, hydrocarbons, oxides of nitrogen, and other pollutants at low temperatures.

  19. Temperature controlled high voltage regulator

    DOE Patents [OSTI]

    Chiaro, Jr., Peter J. (Clinton, TN); Schulze, Gerald K. (Knoxville, TN)

    2004-04-20

    A temperature controlled high voltage regulator for automatically adjusting the high voltage applied to a radiation detector is described. The regulator is a solid state device that is independent of the attached radiation detector, enabling the regulator to be used by various models of radiation detectors, such as gas flow proportional radiation detectors.

  20. Low-temperature magnetic refrigerator

    DOE Patents [OSTI]

    Barclay, J.A.

    1983-05-26

    The invention relates to magnetic refrigeration and more particularly to low temperature refrigeration between about 4 and about 20 K, with an apparatus and method utilizing a belt of magnetic material passed in and out of a magnetic field with heat exchangers within and outside the field operably disposed to accomplish refrigeration.

  1. Low-temperature magnetic refrigerator

    DOE Patents [OSTI]

    Barclay, John A.

    1985-01-01

    The disclosure is directed to a low temperature 4 to 20 K. refrigeration apparatus and method utilizing a ring of magnetic material moving through a magnetic field. Heat exchange is accomplished in and out of the magnetic field to appropriately utilize the device to execute Carnot and Stirling cycles.

  2. High temperature lightweight foamed cements

    DOE Patents [OSTI]

    Sugama, Toshifumi.

    1989-10-03

    Cement slurries are disclosed which are suitable for use in geothermal wells since they can withstand high temperatures and high pressures. The formulation consists of cement, silica flour, water, a retarder, a foaming agent, a foam stabilizer, and a reinforcing agent. A process for producing these cements is also disclosed. 3 figs.

  3. High temperature lightweight foamed cements

    DOE Patents [OSTI]

    Sugama, Toshifumi

    1989-01-01

    Cement slurries are disclosed which are suitable for use in geothermal wells since they can withstand high temperatures and high pressures. The formulation consists of cement, silica flour, water, a retarder, a foaming agent, a foam stabilizer, and a reinforcing agent. A process for producing these cements is also disclosed.

  4. High temperature turbine engine structure

    DOE Patents [OSTI]

    Boyd, Gary L.

    1991-01-01

    A high temperature turbine engine includes a rotor portion having axially stacked adjacent ceramic rotor parts. A ceramic/ceramic joint structure transmits torque between the rotor parts while maintaining coaxial alignment and axially spaced mutually parallel relation thereof despite thermal and centrifugal cycling.

  5. Field Survey of Cactus Crater Storage Facility (Runit Dome)

    SciTech Connect (OSTI)

    Douglas Miller, Terence Holland

    2008-10-31

    The US Department of Energy, Office of Health and Safety (DOE/HS-10), requested that National Security Technologies, LLC, Environmental Management directorate (NSTec/EM) perform a field survey of the Cactus Crater Storage Facility (Runit Dome), similar to past surveys conducted at their request. This field survey was conducted in conjunction with a Lawrence Livermore National Laboratory (LLNL) mission on Runit Island in the Enewetak Atoll in the Republic of the Marshall Islands (RMI). The survey was strictly a visual survey, backed up by digital photos and a written description of the current condition.

  6. THE CATALINA SURVEYS PERIODIC VARIABLE STAR CATALOG

    SciTech Connect (OSTI)

    Drake, A. J.; Graham, M. J.; Djorgovski, S. G.; Mahabal, A. A.; Donalek, C.; Williams, R.; Catelan, M.; Torrealba, G.; García-Álvarez, D.; Prieto, J. L.; Beshore, E.; Larson, S.; Christen sen, E.; Boattini, A.; Gibbs, A.; Hill, R.; Kowalski, R.; Johnson, J.; Belokurov, V.; Koposov, S. E.; and others

    2014-07-01

    We present ∼47,000 periodic variables found during the analysis of 5.4 million variable star candidates within a 20,000 deg{sup 2} region covered by the Catalina Surveys Data Release-1 (CSDR1). Combining these variables with type ab RR Lyrae from our previous work, we produce an online catalog containing periods, amplitudes, and classifications for ∼61,000 periodic variables. By cross-matching these variables with those from prior surveys, we find that >90% of the ∼8000 known periodic variables in the survey region are recovered. For these sources, we find excellent agreement between our catalog and prior values of luminosity, period, and amplitude as well as classification. We investigate the rate of confusion between objects classified as contact binaries and type c RR Lyrae (RRc's) based on periods, colors, amplitudes, metallicities, radial velocities, and surface gravities. We find that no more than a few percent of the variables in these classes are misidentified. By deriving distances for this clean sample of ∼5500 RRc's, we trace the path of the Sagittarius tidal streams within the Galactic halo. Selecting 146 outer-halo RRc's with SDSS radial velocities, we confirm the presence of a coherent halo structure that is inconsistent with current N-body simulations of the Sagittarius tidal stream. We also find numerous long-period variables that are very likely associated within the Sagittarius tidal stream system. Based on the examination of 31,000 contact binary light curves we find evidence for two subgroups exhibiting irregular light curves. One subgroup presents significant variations in mean brightness that are likely due to chromospheric activity. The other subgroup shows stable modulations over more than a thousand days and thereby provides evidence that the O'Connell effect is not due to stellar spots.

  7. THE GALEX NEARBY YOUNG-STAR SURVEY

    SciTech Connect (OSTI)

    Rodriguez, David R.; Faherty, Jacqueline K.; Zuckerman, B.; Kastner, Joel H.; Bessell, M. S.; Murphy, Simon J.

    2013-09-10

    We describe a method that exploits data from the Galaxy Evolution Explorer (GALEX) ultraviolet and Wide-field Infrared Survey Explorer and Two Micron All Sky Survey infrared source catalogs, combined with proper motions and empirical pre-main sequence isochrones, to identify candidate nearby, young, low-mass stars. Applying our method across the full GALEX-covered sky, we identify 2031 mostly M-type stars that, for an assumed age of 10 (100) Myr, all lie within {approx}150 ({approx}90) pc of Earth. The distribution of M spectral subclasses among these {approx}2000 candidate young stars peaks sharply in the range M3-M4; these subtypes constitute 50% of the sample, consistent with studies of the M star population in the immediate solar neighborhood. We focus on a subset of 58 of these candidate young M stars in the vicinity of the Tucana-Horologium association. Only 20 of these 58 candidates were detected in the ROSAT All-Sky X-ray Survey-reflecting the greater sensitivity of GALEX for the purposes of identifying active nearby, young stars, particularly for stars of type M4 and later. Based on statistical analysis of the kinematics and/or spectroscopic followup of these 58 M stars, we find that 50% (29 stars) indeed have properties consistent with Tuc-Hor membership, while 12 are potential new members of the Columba association, and 2 may be AB Dor moving group members. Hence, {approx}75% of our initial subsample of 58 candidates are likely members of young (age {approx} 10-40 Myr) stellar moving groups within 100 pc, verifying that the stellar color- and kinematics-based selection algorithms described here can be used to efficiently isolate nearby, young, low-mass objects from among the field star population. Future studies will focus on characterizing additional subsamples selected from among this list of candidate nearby, young M stars.

  8. Environmental Survey preliminary report, Fermi National Accelerator Laboratory, Batavia, Illinois

    SciTech Connect (OSTI)

    Not Available

    1988-10-01

    This report presents the preliminary findings from the first phase of the Environmental Survey of the US Department of Energy (DOE) Fermi National Accelerator Laboratory (Fermilab), conducted September 14 through 25, 1987. The Survey is being conducted by an interdisciplinary team of environmental specialists led and managed by the Office of Environment, Safety and Health's Office of Environmental Audit. Individual participants for the Survey team are being supplied by a private contractor. The objective of the Survey is to identify environmental problems and areas of environmental risk associated with Fermilab. The Survey covers all environmental media and all areas of environmental regulation. It is being performed in accordance with the DOE Environmental Survey Manual. This phase of the Survey involves the review of existing site environmental data, observations of the operations performed at Fermilab, and interviews with site personnel. 110 refs., 26 figs., 41 tabs.

  9. A Southern Sky Survey with Fermi LAT and ASKAP

    SciTech Connect (OSTI)

    Cameron, Robert A.; /SLAC /KIPAC, Menlo Park

    2010-04-29

    We present the prospects for a future joint gamma-ray and radio survey of southern hemisphere sources using the Fermi Large Area Telescope (LAT) and the upcoming Australian Square Kilometre Array Pathfinder (ASKAP) radio telescope. ASKAP is a next generation radio telescope designed to perform surveys at GHz frequencies at a much higher survey speed than previous radio telescopes, and is scheduled to start engineering observations in 2011. The survey capabilities of both Fermi LAT and ASKAP are described, and the planned science surveys for ASKAP are summarized. We give some expected details of the Variable and Slow Transient (VAST) survey using ASKAP, which will search for transients on timescales from 5 seconds to years. Some observational properties of faint and transient sources seen at gamma-ray and radio wavelengths are summarized, and prospects and strategies for using ASKAP survey data for LAT source counterpart identification are summarized.

  10. SQA_CodeVerification_Survey_FINAL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Survey o f S oftware Q uality Assurance a nd Code Verification Practices i n CASL Michael P ernice Idaho N ational L aboratory Matt S ieger Oak R idge N ational Laboratory March 26, 2 013 INL/EXT-13-28675 CASL-U-2013-0079-000 CASL-U-2013-0079-000 DISCLAIMER This information was prepared as an account of work sponsored by an agency of the U.S. Government. Neither the U.S. Government nor any agency thereof, nor any of their employees, makes any warranty, expressed or implied, or assumes any legal

  11. The Dark Energy Survey CCD imager design

    SciTech Connect (OSTI)

    Cease, H.; DePoy, D.; Diehl, H.T.; Estrada, J.; Flaugher, B.; Guarino, V.; Kuk, K.; Kuhlmann, S.; Schultz, K.; Schmitt, R.L.; Stefanik, A.; /Fermilab /Ohio State U. /Argonne

    2008-06-01

    The Dark Energy Survey is planning to use a 3 sq. deg. camera that houses a {approx} 0.5m diameter focal plane of 62 2kx4k CCDs. The camera vessel including the optical window cell, focal plate, focal plate mounts, cooling system and thermal controls is described. As part of the development of the mechanical and cooling design, a full scale prototype camera vessel has been constructed and is now being used for multi-CCD readout tests. Results from this prototype camera are described.

  12. CMI Industry Survey | Critical Materials Institute

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CMI Industry Survey Thank you for your interest in Critical Materials Institute Education, Training and Outreach. Please share how you are interested in education and training about critical materials. There are additional comment boxes below to allow for any additional ideas you may have. My name is: * I would like to be contacted by telephone, so I am providing a phone number: I would like to be contacted by e-mail; please use this e-mail address: My role in education and outreach about

  13. Commercial Buildings Energy Consumption Survey - Office Buildings

    Reports and Publications (EIA)

    2010-01-01

    Provides an in-depth look at this building type as reported in the 2003 Commercial Buildings Energy Consumption Survey. Office buildings are the most common type of commercial building and they consumed more than 17% of all energy in the commercial buildings sector in 2003. This special report provides characteristics and energy consumption data by type of office building (e.g. administrative office, government office, medical office) and information on some of the types of equipment found in office buildings: heating and cooling equipment, computers, servers, printers, and photocopiers.

  14. UAVs Being Used for Environmental Surveying

    ScienceCinema (OSTI)

    Chung, Sandra

    2013-05-28

    e Arcturus unmanned aerial vehicles, or UAVs, are much more sophisticated than your typical remote-controlled plane. INL robotics and remote sensing experts have added state-of-the-art imaging and wireless technology to the UAVs to create intelligent remote surveillance craft that can rapidly survey a wide area for damage and track down security threats. But these robot planes aren't just for security anymore. Lots more content like this is available at INL's facebook page http://www.facebook.com/idahonationallaboratory.

  15. UAVs Being Used for Environmental Surveying

    SciTech Connect (OSTI)

    Chung, Sandra

    2010-01-01

    e Arcturus unmanned aerial vehicles, or UAVs, are much more sophisticated than your typical remote-controlled plane. INL robotics and remote sensing experts have added state-of-the-art imaging and wireless technology to the UAVs to create intelligent remote surveillance craft that can rapidly survey a wide area for damage and track down security threats. But these robot planes aren't just for security anymore. Lots more content like this is available at INL's facebook page http://www.facebook.com/idahonationallaboratory.

  16. Eighteenth annual T and D construction survey

    SciTech Connect (OSTI)

    Not Available

    1983-08-01

    This survey measures utilities' actual midyear expenditures against projections. The results are cause for mild optimism, although some locales still have problems. Companies represented comprise 77.1% of installed capacity in 48 states and 75.9% of customers: 137 investor-owned utilities, 47 municipals and public power districts, 35 corporations, and 9 state or federal utilities. New and comparative data cover (1) MVA of distribution transformers (46 kW and below), (2) distribution circuit breakers, (3) capacitors (MVAr), (4) distribution substation banks, (5) transmission substation banks, (6) miles of transmission, (7) approximate circuit capability (GW), (8) tranmission circuit breakers, and (9) major construction by regions. 8 figures, 9 tables.

  17. Litchfield Correctional Center District Heating Low Temperature...

    Open Energy Info (EERE)

    Litchfield Correctional Center District Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Litchfield Correctional Center District Heating Low Temperature...

  18. Susanville District Heating District Heating Low Temperature...

    Open Energy Info (EERE)

    Susanville District Heating District Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Susanville District Heating District Heating Low Temperature...

  19. Accelerated Laboratory Tests Using Simultaneous UV, Temperature...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Laboratory Tests Using Simultaneous UV, Temperature, and Moisture for PV Encapsulants, Frontsheets, and Backsheets Accelerated Laboratory Tests Using Simultaneous UV, Temperature, ...

  20. Gone Fishing Aquaculture Low Temperature Geothermal Facility...

    Open Energy Info (EERE)

    Gone Fishing Aquaculture Low Temperature Geothermal Facility Jump to: navigation, search Name Gone Fishing Aquaculture Low Temperature Geothermal Facility Facility Gone Fishing...

  1. Room Temperature Dispenser Photocathode Using Elemental Cesium

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Room Temperature Dispenser Photocathode Using Elemental Cesium Room Temperature Dispenser Photocathode Using Elemental Cesium Los Alamos National Laboratory (LANL) researchers have...

  2. Hyder Valley Aquaculture Low Temperature Geothermal Facility...

    Open Energy Info (EERE)

    Valley Aquaculture Low Temperature Geothermal Facility Jump to: navigation, search Name Hyder Valley Aquaculture Low Temperature Geothermal Facility Facility Hyder Valley Sector...

  3. Countryman Well Greenhouse Low Temperature Geothermal Facility...

    Open Energy Info (EERE)

    Countryman Well Greenhouse Low Temperature Geothermal Facility Jump to: navigation, search Name Countryman Well Greenhouse Low Temperature Geothermal Facility Facility Countryman...

  4. Wards Greenhouses Greenhouse Low Temperature Geothermal Facility...

    Open Energy Info (EERE)

    Wards Greenhouses Greenhouse Low Temperature Geothermal Facility Jump to: navigation, search Name Wards Greenhouses Greenhouse Low Temperature Geothermal Facility Facility Wards...

  5. Express Farms Greenhouse Low Temperature Geothermal Facility...

    Open Energy Info (EERE)

    Express Farms Greenhouse Low Temperature Geothermal Facility Jump to: navigation, search Name Express Farms Greenhouse Low Temperature Geothermal Facility Facility Express Farms...

  6. Hyder Ranch Aquaculture Low Temperature Geothermal Facility ...

    Open Energy Info (EERE)

    Hyder Ranch Aquaculture Low Temperature Geothermal Facility Jump to: navigation, search Name Hyder Ranch Aquaculture Low Temperature Geothermal Facility Facility Hyder Ranch Sector...

  7. Manzanita Estates District Heating Low Temperature Geothermal...

    Open Energy Info (EERE)

    Manzanita Estates District Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Manzanita Estates District Heating Low Temperature Geothermal Facility...

  8. Opline Farms Aquaculture Low Temperature Geothermal Facility...

    Open Energy Info (EERE)

    Opline Farms Aquaculture Low Temperature Geothermal Facility Jump to: navigation, search Name Opline Farms Aquaculture Low Temperature Geothermal Facility Facility Opline Farms...

  9. Liskey Greenhouses Greenhouse Low Temperature Geothermal Facility...

    Open Energy Info (EERE)

    Liskey Greenhouses Greenhouse Low Temperature Geothermal Facility Jump to: navigation, search Name Liskey Greenhouses Greenhouse Low Temperature Geothermal Facility Facility Liskey...

  10. Summer Lake Aquaculture Aquaculture Low Temperature Geothermal...

    Open Energy Info (EERE)

    Summer Lake Aquaculture Aquaculture Low Temperature Geothermal Facility Jump to: navigation, search Name Summer Lake Aquaculture Aquaculture Low Temperature Geothermal Facility...

  11. Marana Aquaculture Low Temperature Geothermal Facility | Open...

    Open Energy Info (EERE)

    Marana Aquaculture Low Temperature Geothermal Facility Jump to: navigation, search Name Marana Aquaculture Low Temperature Geothermal Facility Facility Marana Sector Geothermal...

  12. The Greenhouse Greenhouse Low Temperature Geothermal Facility...

    Open Energy Info (EERE)

    Greenhouse Low Temperature Geothermal Facility Jump to: navigation, search Name The Greenhouse Greenhouse Low Temperature Geothermal Facility Facility The Greenhouse Sector...

  13. Bliss Greenhouse Greenhouse Low Temperature Geothermal Facility...

    Open Energy Info (EERE)

    Greenhouse Greenhouse Low Temperature Geothermal Facility Jump to: navigation, search Name Bliss Greenhouse Greenhouse Low Temperature Geothermal Facility Facility Bliss Greenhouse...

  14. Jackpot Aquaculture Low Temperature Geothermal Facility | Open...

    Open Energy Info (EERE)

    Jackpot Aquaculture Low Temperature Geothermal Facility Jump to: navigation, search Name Jackpot Aquaculture Low Temperature Geothermal Facility Facility Jackpot Sector Geothermal...

  15. Safford Aquaculture Low Temperature Geothermal Facility | Open...

    Open Energy Info (EERE)

    Safford Aquaculture Low Temperature Geothermal Facility Jump to: navigation, search Name Safford Aquaculture Low Temperature Geothermal Facility Facility Safford Sector Geothermal...

  16. Savings Project: Lower Water Heating Temperature | Department...

    Energy Savers [EERE]

    Lower Water Heating Temperature Savings Project: Lower Water Heating Temperature Addthis Project Level Easy Energy Savings 12-30 annually for each 10F reduction Time to ...

  17. High-Temperature Thermoelectric Materials Characterization for...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    High-Temperature Thermoelectric Materials Characterization for Automotive Waste Heat Recovery: Success Stories from the High Temperature Materials Laboratory (HTML) User Program...

  18. Warm Springs Greenhouses Greenhouse Low Temperature Geothermal...

    Open Energy Info (EERE)

    Warm Springs Greenhouses Greenhouse Low Temperature Geothermal Facility Jump to: navigation, search Name Warm Springs Greenhouses Greenhouse Low Temperature Geothermal Facility...

  19. Belmont Springs Hatchery Aquaculture Low Temperature Geothermal...

    Open Energy Info (EERE)

    Springs Hatchery Aquaculture Low Temperature Geothermal Facility Jump to: navigation, search Name Belmont Springs Hatchery Aquaculture Low Temperature Geothermal Facility Facility...

  20. Advanced Low Temperature Absorption Chiller Module Integrated...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Temperature Absorption Chiller Module Integrated with a CHP System at a Distributed Data Center - Presentation by Exergy Partners Corp., June 2011 Advanced Low Temperature ...

  1. Nanostructured High Temperature Bulk Thermoelectric Energy Conversion...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    High Temperature Bulk Thermoelectric Energy Conversion for Efficient Waste Heat Recovery Nanostructured High Temperature Bulk Thermoelectric Energy Conversion for Efficient Waste ...

  2. Lakeview Residences Space Heating Low Temperature Geothermal...

    Open Energy Info (EERE)

    Lakeview Residences Space Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Lakeview Residences Space Heating Low Temperature Geothermal Facility...

  3. Oregon Trail Mushrooms Industrial Low Temperature Geothermal...

    Open Energy Info (EERE)

    Mushrooms Industrial Low Temperature Geothermal Facility Jump to: navigation, search Name Oregon Trail Mushrooms Industrial Low Temperature Geothermal Facility Facility Oregon...

  4. Ennis Laundry Industrial Low Temperature Geothermal Facility...

    Open Energy Info (EERE)

    Ennis Laundry Industrial Low Temperature Geothermal Facility Jump to: navigation, search Name Ennis Laundry Industrial Low Temperature Geothermal Facility Facility Ennis Laundry...

  5. Temperature effects on airgun signatures (Journal Article) |...

    Office of Scientific and Technical Information (OSTI)

    Search Title: Temperature effects on airgun signatures Experiments in an 850 liter water tank were performed in order to study temperature effects on airgun signatures, and to...

  6. Extremely Low Temperature | Open Energy Information

    Open Energy Info (EERE)

    Extremely Low Temperature: No definition has been provided for this term. Add a Definition Sanyal Temp Classification This temperature scheme was developed by Sanyal in...

  7. Manufacturing Barriers to High Temperature PEM Commercialization...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Barriers to High Temperature PEM Commercialization Manufacturing Barriers to High Temperature PEM Commercialization Presented at the NREL Hydrogen and Fuel Cell Manufacturing R&D ...

  8. Nichinghsiang Fish Farm Aquaculture Low Temperature Geothermal...

    Open Energy Info (EERE)

    Nichinghsiang Fish Farm Aquaculture Low Temperature Geothermal Facility Jump to: navigation, search Name Nichinghsiang Fish Farm Aquaculture Low Temperature Geothermal Facility...

  9. Acid Doped Membranes for High Temperature PEMFC

    Broader source: Energy.gov [DOE]

    Presentation on Acid Doped Membranes for High Temperature PEMFC to the High Temperature Membrane Working Group, May 25, 2004 in Philadelphia, PA.

  10. Materials Characterization Capabilities at the High Temperature...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Temperature Materials Laboratory (HTML) User Program Materials Characterization Capabilities at the High Temperature Materials Laboratory and HTML User Program Success Stories ...

  11. ARM - Lesson Plans: Air Density and Temperature

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Teachers' Toolbox Lesson Plans Lesson Plans: Air Density and Temperature Objective The objective of this activity is to investigate the effect of temperature on the density of air. ...

  12. Survey of ceramic machining in Japan

    SciTech Connect (OSTI)

    Bandyopadhyay, B.P.; Blau, P.J.

    1993-07-01

    This report is a compilation of four subcontract reports provided by B. P. Bandyopadhyay who, while a visiting professor at Toyohashi University in Japan, conducted a survey of ceramic machining technology in that country from January 1 through December 31, 1992. Various aspects of machining technology were surveyed: types of parts being produced, types of ceramic materials being used, the nature of current ceramic machining research and development, and types of machine tools. The four separate reports compiled here were originally provided in a narrative, chronological form, and some of the information has been reorganized into topical areas for this compilation. This report is organized into three sections: The first describes ten ceramic machining research and development organizations and provides a reference list of their current technical publications; the second, two major trade shows; and the third, several other products and commercial developments noted during the course of Bandyopadhyay`s stay in Japan. An Appendix lists key individuals who are currently conducting ceramic machining research in Japan.

  13. 2003 survey of Canadian radiation oncology residents

    SciTech Connect (OSTI)

    Yee, Don . E-mail: donyee@cancerboard.ab.ca; Fairchild, Alysa; Keyes, Mira; Butler, Jim; Dundas, George

    2005-06-01

    Purpose: Radiation oncology's popularity as a career in Canada has surged in the past 5 years. Consequently, resident numbers in Canadian radiation oncology residencies are at all-time highs. This study aimed to survey Canadian radiation oncology residents about their opinions of their specialty and training experiences. Methods and Materials: Residents of Canadian radiation oncology residencies that enroll trainees through the Canadian Resident Matching Service were identified from a national database. Residents were mailed an anonymous survey. Results: Eight of 101 (7.9%) potential respondents were foreign funded. Fifty-two of 101 (51.5%) residents responded. A strong record of graduating its residents was the most important factor residents considered when choosing programs. Satisfaction with their program was expressed by 92.3% of respondents, and 94.3% expressed satisfaction with their specialty. Respondents planning to practice in Canada totaled 80.8%, and 76.9% plan to have academic careers. Respondents identified job availability and receiving adequate teaching from preceptors during residency as their most important concerns. Conclusions: Though most respondents are satisfied with their programs and specialty, job availability and adequate teaching are concerns. In the future, limited time and resources and the continued popularity of radiation oncology as a career will magnify the challenge of training competent radiation oncologists in Canada.

  14. High Temperature Heat Exchanger Project

    SciTech Connect (OSTI)

    Anthony E. Hechanova, Ph.D.

    2008-09-30

    The UNLV Research Foundation assembled a research consortium for high temperature heat exchanger design and materials compatibility and performance comprised of university and private industry partners under the auspices of the US DOE-NE Nuclear Hydrogen Initiative in October 2003. The objectives of the consortium were to conduct investigations of candidate materials for high temperature heat exchanger componets in hydrogen production processes and design and perform prototypical testing of heat exchangers. The initial research of the consortium focused on the intermediate heat exchanger (located between the nuclear reactor and hydrogen production plan) and the components for the hydrogen iodine decomposition process and sulfuric acid decomposition process. These heat exchanger components were deemed the most challenging from a materials performance and compatibility perspective

  15. Crystal face temperature determination means

    DOE Patents [OSTI]

    Nason, Donald O.; Burger, Arnold

    1994-01-01

    An optically transparent furnace (10) having a detection apparatus (29) with a pedestal (12) enclosed in an evacuated ampule (16) for growing a crystal (14) thereon. Temperature differential is provided by a source heater (20), a base heater (24) and a cold finger (26) such that material migrates from a polycrystalline source material (18) to grow the crystal (14). A quartz halogen lamp (32) projects a collimated beam (30) onto the crystal (14) and a reflected beam (34) is analyzed by a double monochromator and photomultiplier detection spectrometer (40) and the detected peak position (48) in the reflected energy spectrum (44) of the reflected beam (34) is interpreted to determine surface temperature of the crystal (14).

  16. High temperature turbine engine structure

    DOE Patents [OSTI]

    Carruthers, William D.; Boyd, Gary L.

    1994-01-01

    A high temperature ceramic/metallic turbine engine includes a metallic housing which journals a rotor member of the turbine engine. A ceramic disk-like shroud portion of the engine is supported on the metallic housing portion and maintains a close running clearance with the rotor member. A ceramic spacer assembly maintains the close running clearance of the shroud portion and rotor member despite differential thermal movements between the shroud portion and metallic housing portion.

  17. High temperature turbine engine structure

    DOE Patents [OSTI]

    Carruthers, William D.; Boyd, Gary L.

    1993-01-01

    A high temperature ceramic/metallic turbine engine includes a metallic housing which journals a rotor member of the turbine engine. A ceramic disk-like shroud portion of the engine is supported on the metallic housing portion and maintains a close running clearance with the rotor member. A ceramic spacer assembly maintains the close running clearance of the shroud portion and rotor member despite differential thermal movements between the shroud portion and metallic housing portion.

  18. High temperature turbine engine structure

    DOE Patents [OSTI]

    Carruthers, William D.; Boyd, Gary L.

    1992-01-01

    A high temperature ceramic/metallic turbine engine includes a metallic housing which journals a rotor member of the turbine engine. A ceramic disk-like shroud portion of the engine is supported on the metallic housing portion and maintains a close running clearance with the rotor member. A ceramic spacer assembly maintains the close running clearance of the shroud portion and rotor member despite differential thermal movements between the shroud portion and metallic housing portion.

  19. Battery system with temperature sensors

    DOE Patents [OSTI]

    Wood, Steven J; Trester, Dale B

    2014-02-04

    A battery system includes a platform having an aperture formed therethrough, a flexible member having a generally planar configuration and extending across the aperture, wherein a portion of the flexible member is coextensive with the aperture, a cell provided adjacent the platform, and a sensor coupled to the flexible member and positioned proximate the cell. The sensor is configured to detect a temperature of the cell.

  20. Overview of low temperature sensitization

    SciTech Connect (OSTI)

    Fox, M.J.; McCright, R.D.

    1983-12-01

    A review of the literature on low temperature sensitization (LTS) has been conducted to determine if LTS-related microstructural changes can occur in Type 304L stainless steel within the times and temperatures associated with nuclear waste storage. It was found that Type 304L stainless steel is susceptible to sensitization and LTS, and that cold work plays an important role in determining the rate of LTS. Severely cold worked Type 304L stainless steel would clearly develop LTS-related microstructural changes within the times and temperatures associated with nuclear waste storage. These changes could lead to increased susceptibility to corrosion. Significant improvements in the long-term resistance to sensitization, LTS and corrosion can be achieved by modest changes in alloy composition and fabrication practices. Therefore, Type 304L would not be the preferred alloy of construction for nuclear waste storage canisters. The final qualification of an alternate canister alloy should involve corrosion experiments on actual canisters. Suggestions for alternate canister alloys are 316L, 316LN, 316ELC, 347, and XM-19. 47 references, 4 figures.

  1. Variable temperature semiconductor film deposition

    DOE Patents [OSTI]

    Li, Xiaonan; Sheldon, Peter

    1998-01-01

    A method of depositing a semiconductor material on a substrate. The method sequentially comprises (a) providing the semiconductor material in a depositable state such as a vapor for deposition on the substrate; (b) depositing the semiconductor material on the substrate while heating the substrate to a first temperature sufficient to cause the semiconductor material to form a first film layer having a first grain size; (c) continually depositing the semiconductor material on the substrate while cooling the substrate to a second temperature sufficient to cause the semiconductor material to form a second film layer deposited on the first film layer and having a second grain size smaller than the first grain size; and (d) raising the substrate temperature, while either continuing or not continuing to deposit semiconductor material to form a third film layer, to thereby anneal the film layers into a single layer having favorable efficiency characteristics in photovoltaic applications. A preferred semiconductor material is cadmium telluride deposited on a glass/tin oxide substrate already having thereon a film layer of cadmium sulfide.

  2. Variable temperature semiconductor film deposition

    DOE Patents [OSTI]

    Li, X.; Sheldon, P.

    1998-01-27

    A method of depositing a semiconductor material on a substrate is disclosed. The method sequentially comprises (a) providing the semiconductor material in a depositable state such as a vapor for deposition on the substrate; (b) depositing the semiconductor material on the substrate while heating the substrate to a first temperature sufficient to cause the semiconductor material to form a first film layer having a first grain size; (c) continually depositing the semiconductor material on the substrate while cooling the substrate to a second temperature sufficient to cause the semiconductor material to form a second film layer deposited on the first film layer and having a second grain size smaller than the first grain size; and (d) raising the substrate temperature, while either continuing or not continuing to deposit semiconductor material to form a third film layer, to thereby anneal the film layers into a single layer having favorable efficiency characteristics in photovoltaic applications. A preferred semiconductor material is cadmium telluride deposited on a glass/tin oxide substrate already having thereon a film layer of cadmium sulfide.

  3. Air-quality survey (TAGA 6000), Bakelite Thermosets Limited, Belleville, May-June, 1989: Survey report

    SciTech Connect (OSTI)

    De Brou, G.B.; Ng, A.C.W.

    1989-01-01

    From May 23 to June 2, 1989, an air quality survey was performed in Belleville to determine the level of phenol and ammonia in the ambient air downwind of Bakelite Thermosets Ltd. This report presents the analysis of air samples taken.

  4. Environmental Survey preliminary report, Sandia National Laboratories, Livermore, California

    SciTech Connect (OSTI)

    Not Available

    1988-01-01

    This report contains the preliminary findings based on the first phase of an Environmental Survey at the Department of Energy (DOE) Sandia National Laboratories Livermore (SNLL), located at Livermore, California. The Survey is being conducted by DOE's Office of Environment, Safety and Health. The SNLL Survey is a portion of the larger, comprehensive DOE Environmental Survey encompassing all major operating facilities of DOE. The DOE Environmental Survey is one of a series of initiatives announced on September 18, 1985, by Secretary of Energy, John S. Herrington, to strengthen the environmental, safety, and health programs and activities within DOE. The purpose of the Environmental Survey is to identify, via a no fault'' baseline Survey of all the Department's major operating facilities, environmental problems and areas of environmental risk. The identified problem areas will be prioritized on a Department-wide basis in order of importance in 1989. The findings in this report are subject to modification based on the results from the Sampling and Analysis Phase of the Survey. The findings are also subject to modification based on comments from the Albuquerque Operations Office concerning the technical accuracy of the findings. The modified preliminary findings and any other appropriate changes will be incorporated into an Interim Report. The Interim Report will serve as the site-specific source for environmental information generated by the Survey, and ultimately as the primary source of information for the DOE-wide prioritization of environmental problems in the Survey Summary Report. 43 refs., 21 figs., 24 tabs.

  5. Method and apparatus for optical temperature measurements

    DOE Patents [OSTI]

    Angel, S. Michael; Hirschfeld, Tomas B.

    1988-01-01

    A method and apparatus are provided for remotely monitoring temperature. Both method and apparatus employ a temperature probe material having an excitation-dependent emission line whose fluorescence intensity varies directly with temperature whenever excited by light having a first wavelength and whose fluorescence intensity varies inversely with temperature whenever excited by light having a second wavelength. Temperature is measured by alternatively illuminating the temperature probe material with light having the first wavelength and light having the second wavelength, monitoring the intensity of the successive emissions of the excitation-dependent emission line, and relating the intensity ratio of successive emissions to temperature.

  6. Method and apparatus for optical temperature measurements

    DOE Patents [OSTI]

    Angel, S.M.; Hirschfeld, T.B.

    1986-04-22

    A method and apparatus are provided for remotely monitoring temperature. Both method and apparatus employ a temperature probe material having an excitation-dependent emission line whose fluorescence intensity varies directly with temperature whenever excited by light having a first wavelength and whose fluorescence intensity varies inversely with temperature whenever excited by light having a second wavelength. Temperature is measured by alternatively illiminating the temperature probe material with light having the first wavelength and light having the second wavelength, monitoring the intensity of the successive emissions of the excitation-dependent emission line, and relating the intensity ratio of successive emissions to temperature. 3 figs.

  7. Fuel processor temperature monitoring and control

    DOE Patents [OSTI]

    Keskula, Donald H.; Doan, Tien M.; Clingerman, Bruce J.

    2002-01-01

    In one embodiment, the method of the invention monitors one or more of the following conditions: a relatively low temperature value of the gas stream; a relatively high temperature value of the gas stream; and a rate-of-change of monitored temperature. In a preferred embodiment, the rate of temperature change is monitored to prevent the occurrence of an unacceptably high or low temperature condition. Here, at least two temperatures of the recirculating gas stream are monitored over a period of time. The rate-of-change of temperature versus time is determined. Then the monitored rate-of-change of temperature is compared to a preselected rate-of-change of value. The monitoring of rate-of-change of temperature provides proactive means for preventing occurrence of an unacceptably high temperature in the catalytic reactor.

  8. Low-temperature geothermal assessment of the Santa Clara and Virgin River Valleys, Washington County, Utah

    SciTech Connect (OSTI)

    Budding, K.E.; Sommer, S.N.

    1986-01-01

    Exploration techniques included the following: (1) a temperature survey of springs, (2) chemical analyses and calculated geothermometer temperatures of water samples collected from selected springs and wells, (3) chemical analyses and calculated geothermometer temperatures of spring and well water samples in the literature, (4) thermal gradients measured in accessible wells, and (5) geology. The highest water temperature recorded in the St. George basin is 42/sup 0/C at Pah Tempe Hot Springs. Additional spring temperatures higher than 20/sup 0/C are at Veyo Hot Spring, Washington hot pot, and Green Spring. The warmest well water in the study area is 40/sup 0/C in Middleton Wash. Additional warm well water (higher than 24.5/sup 0/C) is present north of St. George, north of Washington, southeast of St. George, and in Dameron Valley. The majority of the Na-K-Ca calculated reservoir temperatures range between 30/sup 0/ and 50/sup 0/C. Anomalous geothermometer temperatures were calculated for water from Pah Tempe and a number of locations in St. George and vicinity. In addition to the known thermal areas of Pah Tempe and Veyo Hot Spring, an area north of Washington and St. George is delineated in this study to have possible low-temperature geothermal potential.

  9. Data Mining for Security Information: A Survey

    SciTech Connect (OSTI)

    Brugger, S T; Kelley, M; Sumikawa, K; Wakumoto, S

    2001-04-19

    This paper will present a survey of the current published work and products available to do off-line data mining for computer network security information. Hundreds of megabytes of data are collected every second that are of interest to computer security professionals. This data can answer questions ranging from the proactive, ''Which machines are the attackers going to try to compromise?'' to the reactive, ''When did the intruder break into my system and how?'' Unfortunately, there's so much data that computer security professionals don't have time to sort through it all. What we need are systems that perform data mining at various levels on this corpus of data in order to ease the burden of the human analyst. Such systems typically operate on log data produced by hosts, firewalls and intrusion detection systems as such data is typically in a standard, machine readable format and usually provides information that is most relevant to the security of the system. Systems that do this type of data mining for security information fall under the classification of intrusion detection systems. It is important to point out that we are not surveying real-time intrusion detection systems. Instead, we examined what is possible when the analysis is done off-line. Doing the analysis off-line allows for a larger amount of data correlation between distant sites who transfer relevant log files periodically and may be able to take greater advantage of an archive of past logs. Such a system is not a replacement for a real-time intrusion detection system but should be used in conjunction with one. In fact, as noted previously, the logs of the real-time IDS may be one of the inputs to the data mining system. We will concentrate on the application of data mining to network connection data, as opposed to system logs or the output of real-time intrusion detection systems. We do this primarily because this data is readily obtained from firewalls or real-time intrusion detectors and it looks the same regardless of the network architecture or the systems that run on the network. This similarity greatly simplifies the data cleansing step and provides a dataset with high orthogonality between multiple sites, increasing the accuracy of the data mining operations. The decision to use connection logs instead of packet logs is discussed below. This paper will survey both the research that has been done in this area to date and publicly available products that perform such tasks.

  10. Surface water and atmospheric underway carbon data obtained during the World Ocean Circulation Experiment Indian Ocean survey cruises (R/V Knorr, December 1998--January 1996)

    SciTech Connect (OSTI)

    Kozyr, A.; Allison, L.

    1997-11-01

    This data documentation presents the results of the surface water and atmospheric underway measurements of mole fraction of carbon dioxide (xCO{sub 2}), sea surface salinity, and sea surface temperature, obtained during the World Ocean Circulation Experiment (WOCE) Indian Ocean survey cruises (December 1994--January 1996). Discrete and underway carbon measurements were made by members of the CO{sub 2} survey team. The survey team is a part of the Joint Global Ocean Flux Study supported by the US Department of Energy to make carbon-related measurements on the WOCE global survey cruises. Approximately 200,000 surface seawater and 50,000 marine air xCO{sub 2} measurements were recorded.

  11. Quantifying Temperature Effects on Fall Chinook Salmon

    SciTech Connect (OSTI)

    Jager, Yetta

    2011-11-01

    The motivation for this study was to recommend relationships for use in a model of San Joaquin fall Chinook salmon. This report reviews literature pertaining to relationships between water temperature and fall Chinook salmon. The report is organized into three sections that deal with temperature effects on development and timing of freshwater life stages, temperature effects on incubation survival for eggs and alevin, and temperature effects on juvenile survival. Recommendations are made for modeling temperature influences for all three life stages.

  12. The 43rd annual corrosion survey

    SciTech Connect (OSTI)

    Not Available

    1992-03-01

    Applying the science of corrosion prevention to energy (petroleums, oil, LNG) pipelines in actual field operating conditions is a vital aspect of safely and efficiently operating a pipeline system. Ignoring corrosion prevention will allow this never-sleeping enemy to steal the strength from steel pipelines, turning them into dangerous junk. Various methods, techniques and technologies are available to the corrosion control department of cross-country pipelines and gas distribution utilities around the world. Every year, billions of dollars on corrosion control, including everything from coatings to cathodic protection facilities to pigging, are spent to keep these energy pipeline systems in peak operational efficiency. This paper reports that for more than 4 decades, this corrosion survey has sought out the opinions of corrosion control experts, asking them what are the problems they face daily and innovative solutions they have tried to help solve these problems.

  13. Vegetation survey of PEN Branch wetlands

    SciTech Connect (OSTI)

    Not Available

    1991-01-01

    A survey was conducted of vegetation along Pen Branch Creek at Savannah River Site (SRS) in support of K-Reactor restart. Plants were identified to species by overstory, understory, shrub, and groundcover strata. Abundance was also characterized and richness and diversity calculated. Based on woody species basal area, the Pen Branch delta was the most impacted, followed by the sections between the reactor and the delta. Species richness for shrub and groundcover strata were also lowest in the delta. No endangered plant species were found. Three upland pine areas were also sampled. In support of K Reactor restart, this report summarizes a study of the wetland vegetation along Pen Branch. Reactor effluent enters Indian Grove Branch and then flows into Pen Branch and the Pen Branch Delta.

  14. A survey of early warning technologies

    SciTech Connect (OSTI)

    Smith, G.D.; Arlowe, H.D.; Williams, J.D.

    1995-07-01

    This paper presents a survey of technologies useful in providing early warning in physical security systems. Early warning is important in virtually all types of security systems whether they are used for temporary (tactical, portable, or semi-permanent) applications, border warning, fixed-site detection, or standoff surveillance detection. With the exception of the standoff surveillance detection systems, all systems discussed in this paper usually involve a moving target. The fact that a person(s) to be detected in a standoff surveillance scenario is not moving presents challenging problems and requires different applications of technology. The technologies commonly used to detect moving targets and some suggestions for detection of stationary targets are addressed in this paper.

  15. The Building America Indoor Temperature and Humidity Measurement Protocol

    SciTech Connect (OSTI)

    Metzger, C.; Norton, Paul

    2014-02-01

    When modeling homes using simulation tools, the heating and cooling set points can have a significant impact on home energy use. Every four years, the Energy Information Administration (EIA) Residential Energy Consumption Survey (RECS) asks homeowners about their heating and cooling set points. Unfortunately, no temperature data is measured, and most of the time, the homeowner may be guessing at this number. Even one degree Fahrenheit difference in heating set point can make a 5% difference in heating energy use! So, the survey-based RECS data cannot be used as the definitive reference for the set point for the "average occupant" in simulations. The purpose of this document is to develop a protocol for collecting consistent data for heating/cooling set points and relative humidity so that an average set point can be determined for asset energy models in residential buildings. This document covers the decision making process for researchers to determine how many sensors should be placed in each home, where to put those sensors, and what kind of asset data should be taken while they are in the home. The authors attempted to design the protocols to maximize the value of this study and minimize the resources required to achieve that value.

  16. Building America Indoor Temperature and Humidity Measurement Protocol

    SciTech Connect (OSTI)

    Engebrecht-Metzger, C.; Norton, P.

    2014-02-01

    When modeling homes using simulation tools, the heating and cooling set points can have a significant impact on home energy use. Every 4 years the Energy Information Administration (EIA) Residential Energy Consumption Survey (RECS) asks homeowners about their heating and cooling set points. Unfortunately, no temperature data is measured, and most of the time, the homeowner may be guessing at this number. Even one degree Fahrenheit difference in heating set point can make a 5% difference in heating energy use! So, the survey-based RECS data cannot be used as the definitive reference for the set point for the 'average occupant' in simulations. The purpose of this document is to develop a protocol for collecting consistent data for heating/cooling set points and relative humidity so that an average set point can be determined for asset energy models in residential buildings. This document covers the decision making process for researchers to determine how many sensors should be placed in each home, where to put those sensors, and what kind of asset data should be taken while they are in the home. The authors attempted to design the protocols to maximize the value of this study and minimize the resources required to achieve that value.

  17. Integrated survey and design for transmission lines

    SciTech Connect (OSTI)

    Miller, M.A.; Simpson, K.D.

    1994-12-31

    Gathering and compiling information on the features and uses of the land within a proposed corridor provides the basis for selecting a route, obtaining easements, and designing and constructing a transmission line. Traditionally, gathering this information involved searches of existing maps and records to obtain the available information, which would then be supplemented with aerial photography to record current conditions. Ground surveys were performed to collect topographic data for design purposes. This information was manually transferred to drawings and other documents to show the terrain, environmentally sensitive areas, property ownership, and existing facilities. These drawing served as the base to which the transmission line right-of-way, structures, and other design information were added. As the design was completed, these drawings became the source of information for constructing the line and ultimately, the record of the facility. New technologies and the every growing need for instantly accessible information have resulted in changes in almost every step of gathering, storing and using information. Electronic data collection, global positioning systems (GPS), digitized terrain models, computerized design techniques, development of drawings using CAD, and graphical information systems (GIS) have individually resulted in significant advancements in this process. Combining these components into an integrated system, however, is truly revolutionizing transmission line engineering. This paper gives an overview of the survey and mapping information that is required for transmission line projects, review the traditional techniques that have been employed to obtain and utilize this information, and discuss the recent advances in the technology. Additionally, a system is presented that integrates the components in this process to achieve efficiency, minimize chances of errors, and provide improved access to project information.

  18. Paperwork Reduction Act for Surveys and User Research | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Federal Requirements » Paperwork Reduction Act for Surveys and User Research Paperwork Reduction Act for Surveys and User Research The Paperwork Reduction Act requires that all federal websites request permission from the Office of Management and Budget (OMB) before collecting information from 10 or more members of the public. Therefore, surveys and some user experience (UX) research projects for the Office of Energy Efficiency and Renewable Energy (EERE) may require OMB approval

  19. SEARCHING FOR THE HIGHEST REDSHIFT SOURCES IN 250-500 {mu}m SUBMILLIMETER SURVEYS

    SciTech Connect (OSTI)

    Pope, Alexandra; Chary, Ranga-Ram

    2010-06-01

    We explore a technique for identifying the highest redshift (z>4) sources in Herschel/SPIRE and BLAST submillimeter surveys by localizing the position of the far-infrared dust peak. Just as Spitzer/IRAC was used to identify stellar 'bump' sources, the far-IR peak is also a redshift indicator; although the latter also depends on the average dust temperature. We demonstrate the wide range of allowable redshifts for a reasonable range of dust temperatures and show that it is impossible to constraint the redshift of individual objects using solely the position of the far-IR peak. By fitting spectral energy distribution models to simulated Herschel/SPIRE photometry we show the utility of radio and/or far-infrared data in breaking this degeneracy. With prior knowledge of the dust temperature distribution it is possible to obtain statistical samples of high redshift submillimeter galaxy (SMG) candidates. We apply this technique to the BLAST survey of ECDFS to constrain the number of dusty galaxies at z>4. We find 8 {+-} 2 galaxies with flux density ratios of S {sub 500}>S {sub 350}; this sets an upper limit of 17 {+-} 4 deg{sup -2} if we assume all are at z>4. This is <35 % of all 500 {mu}m-selected galaxies down to S {sub 500}>45 mJy (L {sub IR}>2 x 10{sup 13} L {sub sun} for z>4). Modeling with conventional temperature and redshift distributions estimates the percentage of these 500 {mu}m peak galaxies at z>4 to be between 10% and 85%. Our results are consistent with other estimates of the number density of very high redshift SMGs and follow the decline in the star formation rate density at z>4.

  20. University of Illinois Temperature Sensors

    SciTech Connect (OSTI)

    K. L. Davis; D. L. Knudson; J. L. Rempe; B. M. Chase

    2014-09-01

    This document summarizes background information and presents results related to temperature measurements in the Advanced Test Reactor (ATR) National Scientific User Facility (NSUF) University of Illinois Project 29609 irradiation. The objective of this test was to assess the radiation performance of ferritic alloys for advanced reactor applications. The FeCr-based alloy system is considered the lead alloy system for a variety of advanced reactor components and applications. Irradiations of FeCr alloy samples were performed using the Hydraulic Shuttle Irradiation System (HSIS) in the B-7 position and in a static capsule in the A-11 position of the ATR.