Powered by Deep Web Technologies
Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Department of Energy Technical Support Document National Environmental...  

Broader source: Energy.gov (indexed) [DOE]

Energy Technical Support Document National Environmental Policy Act Implementing Procedures Supplement to Notice of Proposed Rulemaking Proposed Changes and Supplemental Supporting...

2

Large Hospital 50% Energy Savings: Technical Support Document  

SciTech Connect (OSTI)

This Technical Support Document documents the technical analysis and design guidance for large hospitals to achieve whole-building energy savings of at least 50% over ANSI/ASHRAE/IESNA Standard 90.1-2004 and represents a step toward determining how to provide design guidance for aggressive energy savings targets. This report documents the modeling methods used to demonstrate that the design recommendations meet or exceed the 50% goal. EnergyPlus was used to model the predicted energy performance of the baseline and low-energy buildings to verify that 50% energy savings are achievable. Percent energy savings are based on a nominal minimally code-compliant building and whole-building, net site energy use intensity. The report defines architectural-program characteristics for typical large hospitals, thereby defining a prototype model; creates baseline energy models for each climate zone that are elaborations of the prototype models and are minimally compliant with Standard 90.1-2004; creates a list of energy design measures that can be applied to the prototype model to create low-energy models; uses industry feedback to strengthen inputs for baseline energy models and energy design measures; and simulates low-energy models for each climate zone to show that when the energy design measures are applied to the prototype model, 50% energy savings (or more) are achieved.

Bonnema, E.; Studer, D.; Parker, A.; Pless, S.; Torcellini, P.

2010-09-01T23:59:59.000Z

3

Grocery Store 50% Energy Savings Technical Support Document  

SciTech Connect (OSTI)

This report documents technical analysis for grocery stores aimed at providing design guidance that achieves whole-building energy savings of at least 50% over ASHRAE Standard 90.1-2004.

Leach, M.; Hale, E.; Hirsch, A.; Torcellini, P.

2009-09-01T23:59:59.000Z

4

General Merchandise 50% Energy Savings Technical Support Document  

SciTech Connect (OSTI)

This report documents technical analysis for medium-box general merchandise stores aimed at providing design guidance that achieves whole-building energy savings of at least 50% over ASHRAE Standard 90.1-2004.

Hale, E.; Leach, M.; Hirsch, A.; Torcellini, P.

2009-09-01T23:59:59.000Z

5

Technical Support Document: 50% Energy Savings for Small Office Buildings  

SciTech Connect (OSTI)

The Technical Support Document (TSD) for 50% energy savings in small office buildings documents the analysis and results for a recommended package of energy efficiency measures (EEMs) referred to as the advanced EEMs. These are changes to a building design that will reduce energy usage. The package of advanced EEMs achieves a minimum of 50% energy savings and a construction area weighted average energy savings of 56.6% over the ANSI/ASHRAE/IESNA Standard 90.1-2004 for 16 cities which represent the full range of climate zones in the United States. The 50% goal is for site energy usage reduction. The weighted average is based on data on the building area of construction in the various climate locations. Cost-effectiveness of the EEMs is determined showing an average simple payback of 6.7 years for all 16 climate locations. An alternative set of results is provided which includes a variable air volume HVAC system that achieves at least 50% energy savings in 7 of the 16 climate zones with a construction area weighted average savings of 48.5%. Other packages of EEMs may also achieve 50% energy savings; this report does not consider all alternatives but rather presents at least one way to reach the goal. Design teams using this TSD should follow an integrated design approach and utilize additional analysis to evaluate the specific conditions of a project.

Thornton, Brian A.; Wang, Weimin; Huang, Yunzhi; Lane, Michael D.; Liu, Bing

2010-04-30T23:59:59.000Z

6

Webinar: Energy Conservation Standards for Dehumidifiers; Availability of the Preliminary Technical Support Document  

Broader source: Energy.gov [DOE]

DOE is conducting a public meeting and webinar for the availability of the preliminary technical support document regarding energy conservation standards for residential dehumidifiers. 79 FR 29380 ...

7

Technical Support Document for Version 3.6.1 of the COMcheck Software  

SciTech Connect (OSTI)

This technical support document (TSD) is designed to explain the technical basis for the COMcheck software as originally developed based on the ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989). Documentation for other national model codes and standards and specific state energy codes supported in COMcheck has been added to this report as appendices. These appendices are intended to provide technical documentation for features specific to the supported codes and for any changes made for state-specific codes that differ from the standard features that support compliance with the national model codes and standards.

Bartlett, Rosemarie; Connell, Linda M.; Gowri, Krishnan; Halverson, Mark A.; Lucas, Robert G.; Richman, Eric E.; Schultz, Robert W.; Winiarski, David W.

2009-09-29T23:59:59.000Z

8

Technical Support Document: 50% Energy Savings Design Technology Packages for Highway Lodging Buildings  

SciTech Connect (OSTI)

This Technical Support Document (TSD) describes the process, methodology and assumptions for development of the 50% Energy Savings Design Technology Packages for Highway Lodging Buildings, a design guidance document intended to provide recommendations for achieving 50% energy savings in highway lodging properties over the energy-efficiency levels contained in ANSI/ASHRAE/IESNA Standard 90.1-2004, Energy Standard for Buildings Except Low-Rise Residential Buildings.

Jiang, Wei; Gowri, Krishnan; Lane, Michael D.; Thornton, Brian A.; Rosenberg, Michael I.; Liu, Bing

2009-09-28T23:59:59.000Z

9

Technical Support Document: 50% Energy Savings Design Technology Packages for Medium Office Buildings  

SciTech Connect (OSTI)

This Technical Support Document (TSD) describes the process and methodology for development of the Advanced Energy Design Guide for Medium Offices (AEDG-MO or the Guide), a design guidance document which intends to provide recommendations for achieving 50% energy savings in medium office buildings that just meet the requirements of ANSI/ASHRAE/IESNA Standard 90.1-2004, Energy Standard for Buildings Except Low-Rise Residential Buildings.

Thornton, Brian A.; Wang, Weimin; Lane, Michael D.; Rosenberg, Michael I.; Liu, Bing

2009-09-01T23:59:59.000Z

10

Technical Support Document for Version 3.9.1 of the COMcheck Software  

SciTech Connect (OSTI)

COMcheck provides an optional way to demonstrate compliance with commercial and high-rise residential building energy codes. Commercial buildings include all use groups except single family and multifamily not over three stories in height. COMcheck was originally based on ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989) requirements and is intended for use with various codes based on Standard 90.1, including the Codification of ASHRAE/IES Standard 90.1-1989 (90.1-1989 Code) (ASHRAE 1989a, 1993b) and ASHRAE/IESNA Standard 90.1-1999 (Standard 90.1-1999). This includes jurisdictions that have adopted the 90.1-1989 Code, Standard 90.1-1989, Standard 90.1-1999, or their own code based on one of these. We view Standard 90.1-1989 and the 90.1-1989 Code as having equivalent technical content and have used both as source documents in developing COMcheck. This technical support document (TSD) is designed to explain the technical basis for the COMcheck software as originally developed based on the ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989). Documentation for other national model codes and standards and specific state energy codes supported in COMcheck has been added to this report as appendices. These appendices are intended to provide technical documentation for features specific to the supported codes and for any changes made for state-specific codes that differ from the standard features that support compliance with the national model codes and standards. Beginning with COMcheck version 3.8.0, support for 90.1-1989, 90.1-1999, and the 1998 IECC and version 3.9.0 support for 2000 and 2001 IECC are no longer included, but those sections remain in this document for reference purposes.

Bartlett, Rosemarie; Connell, Linda M.; Gowri, Krishnan; Halverson, Mark A.; Lucas, Robert G.; Richman, Eric E.; Schultz, Robert W.; Winiarski, David W.

2012-09-01T23:59:59.000Z

11

Technical Support Document for Version 3.9.0 of the COMcheck Software  

SciTech Connect (OSTI)

COMcheck provides an optional way to demonstrate compliance with commercial and high-rise residential building energy codes. Commercial buildings include all use groups except single family and multifamily not over three stories in height. COMcheck was originally based on ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989) requirements and is intended for use with various codes based on Standard 90.1, including the Codification of ASHRAE/IES Standard 90.1-1989 (90.1-1989 Code) (ASHRAE 1989a, 1993b) and ASHRAE/IESNA Standard 90.1-1999 (Standard 90.1-1999). This includes jurisdictions that have adopted the 90.1-1989 Code, Standard 90.1-1989, Standard 90.1-1999, or their own code based on one of these. We view Standard 90.1-1989 and the 90.1-1989 Code as having equivalent technical content and have used both as source documents in developing COMcheck. This technical support document (TSD) is designed to explain the technical basis for the COMcheck software as originally developed based on the ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989). Documentation for other national model codes and standards and specific state energy codes supported in COMcheck has been added to this report as appendices. These appendices are intended to provide technical documentation for features specific to the supported codes and for any changes made for state-specific codes that differ from the standard features that support compliance with the national model codes and standards. Beginning with COMcheck version 3.8.0, support for 90.1-1989, 90.1-1999, and the 1998 IECC are no longer included, but those sections remain in this document for reference purposes.

Bartlett, Rosemarie; Connell, Linda M.; Gowri, Krishnan; Halverson, Mark A.; Lucas, R. G.; Richman, Eric E.; Schultz, Ralph W.; Winiarski, David W.

2011-09-01T23:59:59.000Z

12

Forecast Technical Document Technical Glossary  

E-Print Network [OSTI]

Forecast Technical Document Technical Glossary A document defining some of the terms used in the 2011 Production Forecast technical documentation. Tom Jenkins Robert Matthews Ewan Mackie Lesley in the Forecast documentation. In some cases, the terms and the descriptions are "industry standard", in others

13

Technical Support Document for Version 3.4.0 of the COMcheck Software  

SciTech Connect (OSTI)

COMcheck provides an optional way to demonstrate compliance with commercial and high-rise residential building energy codes. Commercial buildings include all use groups except single family and multifamily not over three stories in height. COMcheck was originally based on ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989) requirements and is intended for use with various codes based on Standard 90.1, including the Codification of ASHRAE/IES Standard 90.1-1989 (90.1-1989 Code) (ASHRAE 1989a, 1993b) and ASHRAE/IESNA Standard 90.1-1999 (Standard 90.1-1999). This includes jurisdictions that have adopted the 90.1-1989 Code, Standard 90.1-1989, Standard 90.1-1999, or their own code based on one of these. We view Standard 90.1-1989 and the 90.1-1989 Code as having equivalent technical content and have used both as source documents in developing COMcheck. This technical support document (TSD) is designed to explain the technical basis for the COMcheck software as originally developed based on the ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989). Documentation for other national model codes and standards and specific state energy codes supported in COMcheck has been added to this report as appendices. These appendices are intended to provide technical documentation for features specific to the supported codes and for any changes made for state-specific codes that differ from the standard features that support compliance with the national model codes and standards.

Bartlett, Rosemarie; Connell, Linda M.; Gowri, Krishnan; Halverson, Mark A.; Lucas, Robert G.; Richman, Eric E.; Schultz, Robert W.; Winiarski, David W.

2007-09-14T23:59:59.000Z

14

Technical support document for the surface disposal of sewage sludge. Final report  

SciTech Connect (OSTI)

The document provides the technical background and justification for the U.S. Environmental Protection Agency's (EPA) final regulation (40 CFR Part 503) covering the surface disposal of sewage sludge. The document summarizes current practices in land application and presents data supporting the risk assessment methodology used to derive human health and environmental risk-based limits for contaminants in sewage sludge placed on surface disposal sites. The management practices associated with surface disposal are outlined and the different pathways by which contaminants reach highly-exposed individuals (HEIs) through surface disposal are discussed.

Not Available

1992-11-01T23:59:59.000Z

15

Technical support document for land application of sewage sludge. Volume 1. Final report  

SciTech Connect (OSTI)

The document provides the technical background and justification for the U.S. Environmental Protection Agency's (EPA) final regulation (40 CFR Part 503) covering the land application of sewage sludge. The document summarizes current practices in land application and presents data supporting the risk assessment methodology used to derive human health and environmental risk-based limits for contaminants in land applied sewage sludge. The management practices associated with land application are outlined and the different pathways by which contaminants reach highly-exposed individuals (HEIs) through land application are discussed.

Jones, A.; Beyer, L.; Rookwood, M.; Pacenka, J.; Bergin, J.

1992-11-01T23:59:59.000Z

16

ISSUANCE: 2014-11-13 Energy Conservation Standards for Commercial Packaged Boilers: Public Meeting and Availability of the Preliminary Technical Support Document  

Broader source: Energy.gov [DOE]

Energy Conservation Standards for Commercial Packaged Boilers: Public Meeting and Availability of the Preliminary Technical Support Document

17

Land application and distribution and marketing of sewage sludge: technical support document  

SciTech Connect (OSTI)

This document provides the technical background and justification for the U.S. Environmental Protection Agency's (EPA) proposed regulation (40 CFR Part 503) covering the land application and distribution and marketing of sewage sludge. The document summarizes current practices in land application and presents data supporting the risk-assessment methodology used to derive human health and environmental risk-based limits for contaminants in land-applied sewage sludge. The underlying assumptions of the methodology, embodied in a series of computer models, are discussed, and the risk-based contaminant limits derived by the models are presented. The three management practices associated with land application are outlined, and the twelve different pathways by which contaminants reach most-exposed individuals through land application are discussed.

Not Available

1986-01-01T23:59:59.000Z

18

Technical Support Document: The Development of the Advanced Energy Design Guide for Highway Lodging Buildings  

SciTech Connect (OSTI)

This Technical Support Document (TSD) describes the process and methodology for development of the Advanced Energy Design Guide for Highway Lodgings (AEDG-HL or the Guide), a design guidance document intended to provide recommendations for achieving 30% energy savings in highway lodging properties over levels contained in ANSI/ASHRAE/IESNA Standard 90.1-1999, Energy Standard for Buildings Except Low-Rise Residential Buildings. The AEDG-HL is the fifth in a series of guides being developed by a partnership of organizations, including the American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc. (ASHRAE), the American Institute of Architects (AIA), the Illuminating Engineering Society of North America (IESNA), the United States Green Buildings Council (USGBC), and the U.S. Department of Energy (DOE).

Jiang, Wei; Jarnagin, Ronald E.; Gowri, Krishnan; McBride, M.; Liu, Bing

2008-09-30T23:59:59.000Z

19

Technical Support Document: Strategies for 50% Energy Savings in Large Office Buildings  

SciTech Connect (OSTI)

This Technical Support Document (TSD) documents technical analysis that informs design guidance for designing and constructing large office buildings that achieve 50% net site energy savings over baseline buildings defined by minimal compliance with respect to ANSI/ASHRAE/IESNA Standard 90.1-2004. This report also represents a step toward developing a methodology for using energy modeling in the design process to achieve aggressive energy savings targets. This report documents the modeling and analysis methods used to identify design recommendations for six climate zones that capture the range of U.S. climate variability; demonstrates how energy savings change between ASHRAE Standard 90.1-2007 and Standard 90.1-2004 to determine baseline energy use; uses a four-story 'low-rise' prototype to analyze the effect of building aspect ratio on energy use intensity; explores comparisons between baseline and low-energy building energy use for alternate energy metrics (net source energy, energy emissions, and energy cost); and examines the extent to which glass curtain construction limits achieve energy savings by using a 12-story 'high-rise' prototype.

Leach, M.; Lobato, C.; Hirsch, A.; Pless, S.; Torcellini, P.

2010-09-01T23:59:59.000Z

20

Technical Support Document: Development of the Advanced Energy Design Guide for Large Hospitals - 50% Energy Savings  

SciTech Connect (OSTI)

This Technical Support Document describes the process and methodology for the development of the Advanced Energy Design Guide for Large Hospitals: Achieving 50% Energy Savings Toward a Net Zero Energy Building (AEDG-LH) ASHRAE et al. (2011b). The AEDG-LH is intended to provide recommendations for achieving 50% whole-building energy savings in large hospitals over levels achieved by following Standard 90.1-2004. The AEDG-LH was created for a 'standard' mid- to large-size hospital, typically at least 100,000 ft2, but the strategies apply to all sizes and classifications of new construction hospital buildings. Its primary focus is new construction, but recommendations may be applicable to facilities undergoing total renovation, and in part to many other hospital renovation, addition, remodeling, and modernization projects (including changes to one or more systems in existing buildings).

Bonnema, E.; Leach, M.; Pless, S.

2013-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Technical Support Document: The Development of the Advanced Energy Design Guide for Small Retail Buildings  

SciTech Connect (OSTI)

The Advanced Energy Design Guide for Small Retail Buildings (AEDG-SR) was developed by a partnership of organizations, including the American Society of Heating, Refrigerating and Air Conditioning Engineers (ASHRAE), the American Institute of Architects (AIA), the Illuminating Engineering Society of North America (IESNA), the United States Green Buildings Council (USGBC), and the Department of Energy (DOE). The guide is intended to offer recommendations to achieve 30% energy savings and thus to encourage steady progress towards net-zero energy buildings. The baseline level energy use was set at buildings built at the turn of the millennium, which are assumed to be based on ANSI/ASHRAE/IESNA Standard 90.1-1999, Energy Standard for Buildings Except Low-Rise Residential Buildings (refer to as the ?Standard? in this report). ASHRAE and its partners are engaged in the development of a series of guides for small commercial buildings, with the AEDG-SR being the second in the series. Previously the partnership developed the Advanced Energy Design Guide for Small Office Buildings: Achieving 30% Energy Savings Over ANSI/ASHRAE/IESNA Standard 90.1-1999, which was published in late 2004. The technical support document prepared by PNNL details how the energy analysis performed in support of the Guide and documents development of recommendation criteria.

Liu, Bing; Jarnagin, Ronald E.; Winiarski, David W.; Jiang, Wei; McBride, Merle F.; Crall, C.

2006-09-30T23:59:59.000Z

22

Technical Support Document: Development of the Advanced Energy Design Guide for Small Office Buildings  

SciTech Connect (OSTI)

This Technical Support Document (TSD) describes the process and methodology for the development of the Advanced Energy Design Guide for Small Office Buildings (AEDG-SO), a design guidance document intended to provide recommendations for achieving 30% energy savings in small office buildings over levels contained in ANSI/ASHRAE/IESNA Standard 90.1-1999, Energy Standard for Buildings Except Low-Rise Residential Buildings. The AEDG-SO is the first in a series of guides being developed by a partnership of organizations, including the American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc. (ASHRAE), the American Institute of Architects (AIA), the Illuminating Engineering Society of North America (IESNA), the New Buildings Institute (NBI), and the U.S. Department of Energy (DOE). Each of the guides in the AEDG series will provide recommendations and user-friendly design assistance to designers, developers and owners of small commercial buildings that will encourage steady progress towards net-zero energy buildings. The guides will provide prescriptive recommendation packages that are capable of reaching the energy savings target for each climate zone in order to ease the burden of the design and construction of energy-efficient small commercial buildings The AEDG-SO was developed by an ASHRAE Special Project committee (SP-102) made up of representatives of each of the partner organizations in eight months. This TSD describes the charge given to the committee in developing the office guide and outlines the schedule of the development effort. The project committee developed two prototype office buildings (5,000 ft2 frame building and 20,000 ft2 two-story mass building) to represent the class of small office buildings and performed an energy simulation scoping study to determine the preliminary levels of efficiency necessary to meet the energy savings target. The simulation approach used by the project committee is documented in this TSD along with the characteristics of the prototype buildings. The prototype buildings were simulated in the same climate zones used by the prevailing energy codes and standards to evaluate energy savings. Prescriptive packages of recommendations presented in the guide by climate zone include enhanced envelope technologies, lighting and day lighting technologies and HVAC and SWH technologies. The report also documents the modeling assumptions used in the simulations for both the baseline and advanced buildings. Final efficiency recommendations for each climate zone are included, along with the results of the energy simulations indicating an average energy savings over all buildings and climates of approximately 38%.

Jarnagin, Ronald E.; Liu, Bing; Winiarski, David W.; McBride, Merle F.; Suharli, L.; Walden, D.

2006-11-30T23:59:59.000Z

23

Technical support document for the proposed Federal Commercial Building energy code  

SciTech Connect (OSTI)

This report presents the justification and technical documentation for all changes and updates made (since 1993) to the Energy Code for Commercial and High-Rise Residential Buildings, the codified version of ASHRAE/IES Standard 90.1-1989, ``Energy Efficient Design of New Buildings Except Low-Rise Residential Buildings.`` These changes and updates, which were subject to the ASHRAE addenda approval process, include Addenda b, c, d, e, g, and i. A seventh addenda, Addenda f, which has not been officially approved by ASHRAE, has been included into the proposed rule. Also included in the changes was technical work conducted to justify revisions to the 1993 DOE lighting power densities. The updated text will be reviewed by the U.S. Department of Energy (DOE) and issued as the new Federal Commercial Building Energy Code (10 CFR 434); Mandatory for New Federal Commercial and Multi-Family High Rise Residential Buildings.

Somasundaram, S.; Halverson, M.A.; Jones, C.C.; Hadley, D.L.

1995-11-01T23:59:59.000Z

24

Data development technical support document for the aircraft crash risk analysis methodology (ACRAM) standard  

SciTech Connect (OSTI)

The Aircraft Crash Risk Analysis Methodology (ACRAM) Panel has been formed by the US Department of Energy Office of Defense Programs (DOE/DP) for the purpose of developing a standard methodology for determining the risk from aircraft crashes onto DOE ground facilities. In order to accomplish this goal, the ACRAM panel has been divided into four teams, the data development team, the model evaluation team, the structural analysis team, and the consequence team. Each team, consisting of at least one member of the ACRAM plus additional DOE and DOE contractor personnel, specializes in the development of the methodology assigned to that team. This report documents the work performed by the data development team and provides the technical basis for the data used by the ACRAM Standard for determining the aircraft crash frequency. This report should be used to provide the generic data needed to calculate the aircraft crash frequency into the facility under consideration as part of the process for determining the aircraft crash risk to ground facilities as given by the DOE Standard Aircraft Crash Risk Assessment Methodology (ACRAM). Some broad guidance is presented on how to obtain the needed site-specific and facility specific data but this data is not provided by this document.

Kimura, C.Y.; Glaser, R.E.; Mensing, R.W.; Lin, T.; Haley, T.A.; Barto, A.B.; Stutzke, M.A.

1996-08-01T23:59:59.000Z

25

Supporting Document Strategic Plan  

E-Print Network [OSTI]

1 Supporting Document Strategic Plan 2013­2020 #12;2 Supporting Document Strategic Plan 2013 more critical to the University's future than was the case in 2005. The purpose of this document are summarised via a SWOT analysis in Appendix 1. This document should therefore be read in conjunction

Auckland, University of

26

Technical support document: Energy conservation standards for consumer products: Refrigerators and furnaces including: environmental impacts regulatory impact analysis  

SciTech Connect (OSTI)

The National Appliance Energy Conversation Act (NAECA) of 1987 (P.L. 100-12) establishes energy efficiency standards for 13 types of consumer products. The legislation requires the Department of Energy (DOE) to consider new or amended standards on these and other types of products at specified times. DOE is currently selecting standards for two types of products: refrigerators, refrigerator-freezers, and freezers; and small gas furnaces. This Technical Support Document presents the methodology, data and results from the analysis of the energy and economic impacts of the proposed standards. 8 refs., 39 figs., 135 tabs.

Not Available

1989-11-01T23:59:59.000Z

27

Technical approach document  

SciTech Connect (OSTI)

The Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978, Public Law 95-604 (PL95-604), grants the Secretary of Energy the authority and responsibility to perform such actions as are necessary to minimize radiation health hazards and other environmental hazards caused by inactive uranium mill sites. This Technical Approach Document (TAD) describes the general technical approaches and design criteria adopted by the US Department of Energy (DOE) in order to implement remedial action plans (RAPS) and final designs that comply with EPA standards. It does not address the technical approaches necessary for aquifer restoration at processing sites; a guidance document, currently in preparation, will describe aquifer restoration concerns and technical protocols. This document is a second revision to the original document issued in May 1986; the revision has been made in response to changes to the groundwater standards of 40 CFR 192, Subparts A--C, proposed by EPA as draft standards. New sections were added to define the design approaches and designs necessary to comply with the groundwater standards. These new sections are in addition to changes made throughout the document to reflect current procedures, especially in cover design, water resources protection, and alternate site selection; only minor revisions were made to some of the sections. Sections 3.0 is a new section defining the approach taken in the design of disposal cells; Section 4.0 has been revised to include design of vegetated covers; Section 8.0 discusses design approaches necessary for compliance with the groundwater standards; and Section 9.0 is a new section dealing with nonradiological hazardous constituents. 203 refs., 18 figs., 26 tabs.

Not Available

1989-12-01T23:59:59.000Z

28

Technical support document: Survey data used in revising the energy conservation requirements in the manufactured home construction and safety standards  

SciTech Connect (OSTI)

This report documents data used in the development of revised energy conservation standards for manufactured housing. The approach used in developing the proposed standard revision is a cost-benefit analysis in which the costs of energy conservation measures (ECM) are balanced against the benefits of energy savings. The analysis used to develop the recommendations for revision of the US Department of Housing and Urban Development (HUD) energy conservation standards for manufactured housing requires information on specific ECMs. This technical support document contains the data from two of the three surveys that were used primarily to characterize the available ECMs and their associated costs. The analyses of these data are provided in separate reports. 5 refs.

Lee, A.D.; Conner, C.C.

1992-02-01T23:59:59.000Z

29

2014-11-25 Issuance: Energy Conservation Standards for Miscellaneous Refrigeration Products; Notice of Open Meeting and Availability of the Preliminary Technical Support Document  

Broader source: Energy.gov [DOE]

This document is a pre-publication Federal Register notice of open meeting and availability of the preliminary technical support document regarding energy conservation standards for miscellaneous refrigeration products, as issued by the Deputy Assistant Secretary for Energy Efficiency on November 25, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

30

2014-10-27 Issuance: Energy Conservation Standards for Ceiling Fan Light Kits; Notice of Public Meeting and Availability of the Preliminary Technical Support Document  

Broader source: Energy.gov [DOE]

This document is a pre-publication Federal Register notice of public meeting and availability of the preliminary technical support document regarding energy conservation standards for ceiling fan light kits, as issued by the Deputy Assistant Secretary for Energy Efficiency on October 27, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

31

2014-09-16 Issuance: Energy Conservation Standards for Ceiling Fans; Notice of Public Meeting and Availability of Preliminary Technical Support Document  

Broader source: Energy.gov [DOE]

This document is a pre-publication Federal Register notice of public meeting and availability of preliminary technical support document regarding energy conservation standards for ceiling fans, as issued by the Deputy Assistant Secretary on September 16, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

32

2014-08-01 Issuance: Energy Conservation Standard for Refrigerated Bottled or Canned Beverage Vending Machines; Notice of Public Meeting and Availability of the Preliminary Technical Support Document  

Broader source: Energy.gov [DOE]

This document is a pre-publication Federal Register notice of public meeting and availability of the preliminary technical support document for refrigerated bottled or canned beverage vending machines, as issued by the Deputy Assistant Secretary for Energy Efficiency on August 1, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

33

Guidance document for revision of DOE Order 5820.2A, Radioactive Waste Technical Support Program. Revision 1  

SciTech Connect (OSTI)

This document provides guidance for the revision of DOE Order 5820.2A, ``Radioactive Waste Management.`` Technical Working Groups have been established and are responsible for writing the revised order. The Technical Working Groups will use this document as a reference for polices and procedures that have been established for the revision process. The overall intent of this guidance is to outline how the order will be revised and how the revision process will be managed. In addition, this document outlines technical issues considered for inclusion by a Department of Energy Steering Committee.

Kudera, D.E.; McMurtrey, C.D.; Meagher, B.G.

1993-04-01T23:59:59.000Z

34

Technical Support Document: Development of the Advanced Energy Design Guide for Medium to Big Box Retail Buildings - 50% Energy Savings  

SciTech Connect (OSTI)

This Technical Support Document describes the process and methodology for the development of the Advanced Energy Design Guide for Medium to Big Box Retail Buildings: Achieving 50% Energy Savings Toward a Net Zero Energy Building (AEDG-MBBR) ASHRAE et al. (2011b). The AEDG-MBBR is intended to provide recommendations for achieving 50% whole-building energy savings in retail stores over levels achieved by following ANSI/ASHRAE/IESNA Standard 90.1-2004, Energy Standard for Buildings Except Low-Rise Residential Buildings (Standard 90.1-2004) (ASHRAE 2004b). The AEDG-MBBR was developed in collaboration with the American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE), the American Institute of Architects (AIA), the Illuminating Engineering Society of North America (IES), the U.S. Green Building Council (USGBC), and the U.S. Department of Energy.

Bonnema, E.; Leach, M.; Pless, S.

2013-06-01T23:59:59.000Z

35

Technical Support Document: 50% Energy Savings for Quick-Service Restaurants  

SciTech Connect (OSTI)

Document describing PNNL's project to develop a package of energy efficiency measures that demonstrate the feasibility of achieving a 50% energy savings for quick-service restaurants with a simple payback of 5 years or less.

Zhang, Jian; Schrock, D. W.; Fisher, D. R.; Livchak, A.; Zabrowski, D. A.; Athalye, Rahul A.; Liu, Bing

2010-09-30T23:59:59.000Z

36

Technical Support Document for the Department of Energy's Notice of Final  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-Up from theDepartment of Energy Technical Evaluation ofRulemaking | Department of

37

Issuance 2014-11-21:Energy Efficiency Program for Consumer Products: Energy Conservation Standards for Ceiling Fans: Availability of the Preliminary Technical Support Document, Notice of Comment Period Extension  

Broader source: Energy.gov [DOE]

Energy Efficiency Program for Consumer Products: Energy Conservation Standards for Ceiling Fans: Availability of the Preliminary Technical Support Document, Notice of Comment Period Extension

38

Technical support document for proposed revision of the model energy code thermal envelope requirements  

SciTech Connect (OSTI)

This report documents the development of the proposed revision of the council of American Building Officials' (CABO) 1993 supplement to the 1992 Model Energy Code (MEC) (referred to as the 1993 MEC) building thermal envelope requirements for single-family and low-rise multifamily residences. The goal of this analysis was to develop revised guidelines based on an objective methodology that determined the most cost-effective (least total life-cycle cost [LCC]) combination of energy conservation measures (ECMs) for residences in different locations. The ECMs with the lowest LCC were used as a basis for proposing revised MEC maximum U[sub o]-value (thermal transmittance) curves in the MEC format. The changes proposed here affect the requirements for group R'' residences. The group R residences are detached one- and two-family dwellings (referred to as single-family) and all other residential buildings three stories or less (referred to as multifamily).

Conner, C.C.; Lucas, R.G.

1993-02-01T23:59:59.000Z

39

Technical support document for proposed revision of the model energy code thermal envelope requirements  

SciTech Connect (OSTI)

This report documents the development of the proposed revision of the council of American Building Officials` (CABO) 1993 supplement to the 1992 Model Energy Code (MEC) (referred to as the 1993 MEC) building thermal envelope requirements for single-family and low-rise multifamily residences. The goal of this analysis was to develop revised guidelines based on an objective methodology that determined the most cost-effective (least total life-cycle cost [LCC]) combination of energy conservation measures (ECMs) for residences in different locations. The ECMs with the lowest LCC were used as a basis for proposing revised MEC maximum U{sub o}-value (thermal transmittance) curves in the MEC format. The changes proposed here affect the requirements for ``group R`` residences. The group R residences are detached one- and two-family dwellings (referred to as single-family) and all other residential buildings three stories or less (referred to as multifamily).

Conner, C.C.; Lucas, R.G.

1993-02-01T23:59:59.000Z

40

Cost-Effectiveness Analysis of the 2009 and 2012 IECC Residential Provisions – Technical Support Document  

SciTech Connect (OSTI)

This analysis was conducted by Pacific Northwest National Laboratory (PNNL) in support of the U.S. Department of Energy’s (DOE) Building Energy Codes Program (BECP). DOE supports the development and adoption of efficient residential and commercial building energy codes. These codes set the minimum requirements for energy efficient building design and construction and ensure energy savings on a national level. This analysis focuses on one and two family dwellings, townhomes, and low-rise multifamily residential buildings. For these buildings, the basis of the energy codes is the International Energy Conservation Code (IECC). This report does not address commercial and high-rise residential buildings, which reference ANSI/ASHRAE/IES Standard 90.1.

Mendon, Vrushali V.; Lucas, Robert G.; Goel, Supriya

2012-12-04T23:59:59.000Z

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Technical support document for proposed 1994 revision of the MEC thermal envelope requirements  

SciTech Connect (OSTI)

This report documents the development of the proposed revision of the Council of American Building Officials` (CABO) 1994 supplement to the 1993 Model Energy Code (MEC) building thermal envelope requirements for maximum component U{sub 0}-value. The 1994 amendments to the 1993 MEC were established in last year`s code change cycle and did not change the envelope requirements. The research underlying the proposed MEC revision was conducted by Pacific Northwest Laboratory (PNL) for the US Department of Energy (DOE) Building Energy Standards program. The goal of this research was to develop revised guidelines based on an objective methodology that determines the most cost-effective (least total cost) combination of energy conservation measures (ECMs) (insulation levels and window types) for residential buildings. This least-cost set of ECMs was used as a basis for proposing revised MEC maximum U{sub 0}-values (thermal transmittances). ECMs include window types (for example, double-pane vinyl) and insulation levels (for example, R-19) for ceilings, walls, and floors.

Conner, C.C.; Lucas, R.G.

1994-03-01T23:59:59.000Z

42

Forecast Technical Document Forecast Types  

E-Print Network [OSTI]

Forecast Technical Document Forecast Types A document describing how different forecast types are implemented in the 2011 Production Forecast system. Tom Jenkins Robert Matthews Ewan Mackie Lesley Halsall #12;PF2011 ­ Forecast Types Background Different `types' of forecast are possible for a specified area

43

Forecast Technical Document Tree Species  

E-Print Network [OSTI]

Forecast Technical Document Tree Species A document listing the tree species included in the 2011 Production Forecast Tom Jenkins Justin Gilbert Ewan Mackie Robert Matthews #12;PF2011 ­ List of tree species The following is the list of species used within the Forecast System. Species are ordered alphabetically

44

Forecast Technical Document Volume Increment  

E-Print Network [OSTI]

Forecast Technical Document Volume Increment Forecasts A document describing how volume increment is handled in the 2011 Production Forecast. Tom Jenkins Robert Matthews Ewan Mackie Lesley Halsall #12;PF2011 ­ Volume increment forecasts Background A volume increment forecast is a fundamental output of the forecast

45

Technical support for amending standards for management of uranium byproduct materials: 40 cfr part 192-subpart d. Background information document  

SciTech Connect (OSTI)

The Environmental Protection Agency (EPA) is amending 40 CFR 192, Subpart D, dealing with disposal of uranium mill tailings at non-operational sites licensed by the Nuclear Regulatory Commission (NRC) or an agreement state pursuant to the Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978. The Background Information Document (BID) was prepared in support of the rulemaking proceedings for EPA's action. The BID only considers long-term disposal of tailings at facilities licensed by the NRC or an agreement state, and designated Title II facilities in the UMTRCA.

Not Available

1993-10-01T23:59:59.000Z

46

Technical documentation in support of the project-specific analysis for construction and operation of the National Ignition Facility  

SciTech Connect (OSTI)

This document provides information that supports or supplements the data and impact analyses presented in the National Ignition Facility (NIF) Project-Specific Analysis (PSA). The purposes of NIF are to achieve fusion ignition in the laboratory for the first time with inertial confinement fusion (ICF) technology and to conduct high- energy-density experiments ins support of national security and civilian application. NIF is an important element in the DOE`s science-based SSM Program, a key mission of which is to ensure the reliability of the nation`s enduring stockpile of nuclear weapons. NIF would also advance the knowledge of basic and applied high-energy- density science and bring the nation a large step closer to developing fusion energy for civilian use. The NIF PSA includes evaluations of the potential environmental impacts of constructing and operating the facility at one of five candidate site and for two design options.

Lazaro, M.A.; Vinikour, W. [Argonne National Lab., IL (United States). Environmental Assessment Div.; Allison, T. [Argonne National Lab., IL (United States). Decision and Information Sciences Div.] [and others

1996-09-01T23:59:59.000Z

47

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. 1732-S 2. Government Accession No. 3. Recipients, geometric design, entrance ramps, exit ramps 18. Distribution Statement No restrictions. This document

Texas at Austin, University of

48

PRELIMINARY REVIEW COPY Technical Report Documentation Page  

E-Print Network [OSTI]

PRELIMINARY REVIEW COPY Technical Report Documentation Page 1. Report No. 2941-3 Preliminary Review, long-term monitoring 18. Distribution Statement No restrictions. This document is available

Texas at Austin, University of

49

TECHNICAL BASIS DOCUMENT FOR NATURAL EVENT HAZARDS  

SciTech Connect (OSTI)

This technical basis document was developed to support the documented safety analysis (DSA) and describes the risk binning process and the technical basis for assigning risk bins for natural event hazard (NEH)-initiated accidents. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous conditions based on an evaluation of the frequency and consequence. Note that the risk binning process is not applied to facility workers, because all facility worker hazardous conditions are considered for safety-significant SSCs and/or TSR-level controls.

KRIPPS, L.J.

2006-07-31T23:59:59.000Z

50

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-00-1795-S 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

51

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-4485-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

Texas at Austin, University of

52

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-00/0-1843-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

Texas at Austin, University of

53

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-03/4083-2 2. Government Accession No. 3. This document is available to the public through the National Technical Information Service, Springfield

Texas at Austin, University of

54

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-12/5-4829-01-3 2. Government Accession No No restrictions. This document is available to the public through the National Technical Information Service

Zornberg, Jorge G.

55

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-0-1814-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

Texas at Austin, University of

56

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-10/0-5812-1 2. Government Accession No. 3. This document is available to the public through the National Technical Information Service, Springfield

Zornberg, Jorge G.

57

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-03-1838-8 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

58

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-00/1754-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

Texas at Austin, University of

59

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-05/9-580/589-2 2. Government Accession No. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

60

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-04/1778-4 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

Texas at Austin, University of

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-04/0-1734-S 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

Texas at Austin, University of

62

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-11/0-6348-1 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

63

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-00/1785-2 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

Texas at Austin, University of

64

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-03/4386-1 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

65

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-06/0-4085-5 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

66

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-06/0-1401-2 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

67

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-10/0-5974-1 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

68

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-04/0-1471-4 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

69

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-0-1748-2 2. Government Accession No. 3. This document is available to the public through the National Technical Information Service, Springfield

Texas at Austin, University of

70

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-04/0-4808-1 2. Government Accession No. 3. This document is available to the public through the National Technical Information Service, Springfield

Texas at Austin, University of

71

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-09/0-6048-1 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Zornberg, Jorge G.

72

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-04/5-3933-01-P1-4 2. Government Accession No restrictions. This document is available to the public through the National Technical Information Service

Texas at Austin, University of

73

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-06/0-4437-1 2. Government Accession No. 3. This document is available to the public through the National Technical Information Service, Springfield

Texas at Austin, University of

74

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-06/5-4975-01-1 2. Government Accession No. This document is available to the public through the National Technical Information Service, Springfield

Texas at Austin, University of

75

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-06/0-4185-4 2. Government Accession No. 3. This document is available to the public through the National Technical Information Service, Springfield

Texas at Austin, University of

76

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-06/0-4958-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

Texas at Austin, University of

77

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-11/0-6095-2 2. Government Accession No. 3 Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

78

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-07/0-1700-7 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

79

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-07/0-5410-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

Texas at Austin, University of

80

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-4661-1 2. Government Accession No. 3. This document is available to the public through the National Technical Information Service, Springfield

Texas at Austin, University of

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-04/0-1700-1 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

82

PRELIMINARY REVIEW COPY Technical Report Documentation Page  

E-Print Network [OSTI]

PRELIMINARY REVIEW COPY Technical Report Documentation Page 1. Report No. FHWA/TX-13/0-6603-2 2 No restrictions. This document is available to the public through the National Technical Information Service

Zornberg, Jorge G.

83

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-04/4576-3 2. Government Accession No. 3 Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

84

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-09/0-5799-1 2. Government Accession No. 3 Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

85

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-7-4957-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

Texas at Austin, University of

86

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-4416-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

Texas at Austin, University of

87

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-07/0-1895-1 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

88

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-0-2129-1 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

89

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-4410-2 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

90

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-09/0-5830-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

Texas at Austin, University of

91

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-4069-1 2. Government Accession No. 3. This document is available to the public through the National Technical Information Service, Springfield

Texas at Austin, University of

92

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. 9-572-1 2. Government Accession No. 3. Recipient Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

93

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-06/0-4661-2 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

94

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-1713-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

Texas at Austin, University of

95

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-07/0-5202-2 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

Zornberg, Jorge G.

96

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-4185-3 2. Government Accession No. 3 Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

97

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-10/0-5973-2 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

98

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-13/5-4829-01-2 2. Government Accession No. This document is available to the public through the National Technical Information Service, Springfield

Zornberg, Jorge G.

99

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-1713-2 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

100

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-07/0-5176-2 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-05/5-1924-01-1 2. Government Accession No No restrictions. This document is available to the public through the National Technical Information Service

Texas at Austin, University of

102

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-09/0-5668-1 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

103

Technical Documentation and Verification for the  

E-Print Network [OSTI]

PNNL-15202 Technical Documentation and Verification for the Buildings Module in the Visual Sample://www.ntis.gov/ordering.htm This document was printed on recycled paper. (9/2003) #12;PNNL-15202 Technical Documentation and Verification ...................................................................... 1 2.0 Documentation of Statistical Methods and Computations

104

Technical background document for soil screening guidance. Review draft  

SciTech Connect (OSTI)

The document provides the technical background behind the development of the November 1994 Soil Screening Guidance for Superfund. These documents define the Soil Screening framework, a suite of methodologies for developing Soil Screening Levels (SSLs) for 107 chemicals commonly found at Superfund sites. The document is an updated version of the background document developed in support of the September 30, 1993, draft SSL guidance (PB93-963508). The document and the Guidance is available for public comment and is currently undergoing extensive peer review. Because the guidance is still under review, it and this document should not be used until they are finalized following this rigorous technical review and public comment.

Not Available

1994-12-01T23:59:59.000Z

105

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-1778-3 2. Government Accession No. 3, and others. A number of reports, tables, and queries have been prepared and documented herein showing example. This document is available to the public through the National Technical Information Service, Springfield

Texas at Austin, University of

106

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-1778-6 2. Government Accession No. 3 summarizes the tasks conducted under TxDOT Project 0-1778 "TxDOT Rigid Pavement Database." This document report is the final technical document prepared for the project. Additional information is provided

Texas at Austin, University of

107

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-04/0-4266-2 2. Government Accession No. 3 significant changes in traffic operation and safety. A review of the design standard documents shows Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

108

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-10/0-5517-1 2. Government Accession No. 3 for a series of tire bale case histories. The following document outlines all the work conducted as part Statement No restrictions. This document is available to the public through the National Technical

Texas at Austin, University of

109

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-04/0-1405-7 2. Government Accession No. 3 researchers, after an extensive literature review. This report documents the final evaluation of the long No restrictions. This document is available to the public through the National Technical Information Service

Texas at Austin, University of

110

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-04/5-1873-01-1 2. Government Accession No to improve safety and facilitate traffic flow. Finally, they documented these design considerations. This document is available to the public through the National Technical Information Service, Springfield

Texas at Austin, University of

111

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-10/0-6044-1 2. Government Accession No. 3 the researchers' understanding of the general T&R approach used by the industry, (c) documents the research No restrictions. This document is available to the public through the National Technical Information Service

Texas at Austin, University of

112

Appendix G Supporting Documentation  

Office of Legacy Management (LM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarlyEnergyDepartment ofDepartment ofofOxford SiteToledo SiteTonawanda North Site ThisSupporting

113

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-02/1884-2 2. Government Accession No. 3, paratransit systems 18. Distribution Statement No restrictions. This document is available to the public

Texas at Austin, University of

114

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-09/0-5367-1 2. Government Accession No. 3, deck, slab, shear, fatigue 18. Distribution Statement No restrictions. This document is available

Texas at Austin, University of

115

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-03/4382-1 2. Government Accession No. 3, concrete pavement, sensitivity, fatigue, distress 18. Distribution Statement No restrictions. This document

Texas at Austin, University of

116

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-10/5-4829-01-1 2. Government Accession No, stiffness 18. Distribution Statement No restrictions. This document is available to the public through

Zornberg, Jorge G.

117

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. 1747-3 2. Government Accession No. 3. Recipient, Information Technology 18. Distribution Statement No restrictions. This document is available to the public

Texas at Austin, University of

118

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-10/5-5517-01-1 2. Government Accession No, field monitoring 18. Distribution Statement No restrictions. This document is available to the public

Zornberg, Jorge G.

119

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-0-2122-1 2. Government Accession No. 3, regulations, vehicle characteristics 18. Distribution Statement No restrictions. This document is available

Texas at Austin, University of

120

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FWHA/TX-05/0-1774-3 2. Government Accession No. 3, rehabilitation, encapsulation 18. Distribution Statement No restrictions. This document is available

Texas at Austin, University of

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-09/0-5197-4 2. Government Accession No. 3 consolidating concrete, microcracking 18. Distribution Statement No restrictions. This document is available

Texas at Austin, University of

122

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-03/1892-1 2. Government Accession No. 3, nondestructive testing 18. Distribution Statement No restrictions. This document is available to the public

Texas at Austin, University of

123

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-05/9-580/589-1 2. Government Accession No resistance, creep, shrinkage 18. Distribution Statement No restrictions. This document is available

Texas at Austin, University of

124

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-08/0-4562-2 2. Government Accession No. 3 concrete 18. Distribution Statement No restrictions. This document is available to the public through

Texas at Austin, University of

125

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-04/0-1405-9 2. Government Accession No. 3 joints, reinforcement coatings 18. Distribution Statement No restrictions. This document is available

Texas at Austin, University of

126

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-03/1898-1 2. Government Accession No. 3 after the deck had hardened. 17. Key Words 18. Distribution Statement No restrictions. This document

Texas at Austin, University of

127

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-00/1795-1 2. Government Accession No. 3 strategies 18. Distribution Statement No restrictions. This document is available to the public through

Texas at Austin, University of

128

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-02/1395-2F 2. Government Accession No. 3 Bracing, Brace Forces, Torsional Stiffness 18. Distribution Statement No restrictions. This document

Texas at Austin, University of

129

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-02-1810-2 2. Government Accession No. 3 in Texas 18. Distribution Statement No restrictions. This document is available to the public through

Texas at Austin, University of

130

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-04/5-1291-01-1 2. Government Accession No),PASSER II, GEOPAK, Vehicle Turn Templates 18. Distribution Statement No restrictions. This document

Texas at Austin, University of

131

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

i Technical Report Documentation Page 1. Report No. FHWA/TX-07 / 0-1774-4 2. Government Accession, encapsulation 18. Distribution Statement No restrictions. This document is available to the public through

Texas at Austin, University of

132

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-10/0-5185-3 2. Government Accession No. 3 Pavement. 18. Distribution Statement No restrictions. This document is available to the public through

Texas at Austin, University of

133

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-02/1852-1 2. Government Accession No. 3 concrete mix design 18. Distribution Statement No restrictions. This document is available to the public

Texas at Austin, University of

134

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-08/5-4958-01-1 2. Government Accession No lens 18. Distribution Statement No restrictions. This document is available to the public through

Texas at Austin, University of

135

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-03-1810-3 2. Government Accession No. 3, Highway user taxes, Highway finance 18. Distribution Statement No restrictions. This document is available

Texas at Austin, University of

136

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

FINAL COPY Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-1700-2 2. Government-based specifications. 18. Distribution Statement No restrictions. This document is available to the public through

Texas at Austin, University of

137

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-07/0-5202-3 2. Government Accession No. 3 Shale, Paris Clay, Beaumont Clay. 18. Distribution Statement No restrictions. This document is available

Zornberg, Jorge G.

138

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-07/0-4080-8 2. Government Accession No. 3 frameworks, econometric models, empirical results 18. Distribution Statement No restrictions. This document

Texas at Austin, University of

139

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. 0-4080-1 2. Government Accession No. 3. Recipient modeling 18. Distribution Statement No restrictions. This document is available to the public through

Texas at Austin, University of

140

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-7-2957-2 2. Government Accession No. 3/pavement interaction, pavement noise, noise level. 18. Distribution Statement No restrictions. This document

Texas at Austin, University of

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FWHA/TX-04/0-1741-4 2. Government Accession No. 3 Administration, and the Texas Department of Transportation. 16. Abstract This report documents the results, rehabilitation, evaluation 18. Distribution Statement No restrictions. This document is available to the public

Texas at Austin, University of

142

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-10/0-6655-CT-1 2. Government Accession No presents four documents created by the TxDOT Multi-Tier Pavement Management Workgroup. 17. Key Words System Operation, Preservation Optimization 18. Distribution Statement No restrictions. This document is available

Texas at Austin, University of

143

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-1778-5 2. Government Accession No. 3 and funded by the Texas Department of Transportation (TxDOT). Project 0-1778 documents the efforts conducted-Button, Pavement Distress Index (PDI), z-score. 18. Distribution Statement No restrictions. This document

Texas at Austin, University of

144

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-06/0-4085-1 2. Government Accession No. 3-related problems. Research is currently underway to document the performance of concrete using these mitigation Formation (DEF) 18. Distribution Statement No restrictions. This document is available to the public through

Texas at Austin, University of

145

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA-IF-02-034 2. Government Accession No. 3. DiMaggio 16. Abstract This document presents state-of-the-practice information on the evaluation of soil and rock properties for geotechnical design applications. This document addresses the entire range

Mayne, Paul W.

146

Technical support document: Energy conservation standards for consumer products: Dishwashers, clothes washers, and clothes dryers including: Environmental impacts; regulatory impact analysis  

SciTech Connect (OSTI)

The Energy Policy and Conservation Act as amended (P.L. 94-163), establishes energy conservation standards for 12 of the 13 types of consumer products specifically covered by the Act. The legislation requires the Department of Energy (DOE) to consider new or amended standards for these and other types of products at specified times. This Technical Support Document presents the methodology, data and results from the analysis of the energy and economic impacts of standards on dishwashers, clothes washers, and clothes dryers. The economic impact analysis is performed in five major areas: An Engineering Analysis, which establishes technical feasibility and product attributes including costs of design options to improve appliance efficiency. A Consumer Analysis at two levels: national aggregate impacts, and impacts on individuals. The national aggregate impacts include forecasts of appliance sales, efficiencies, energy use, and consumer expenditures. The individual impacts are analyzed by Life-Cycle Cost (LCC), Payback Periods, and Cost of Conserved Energy (CCE), which evaluate the savings in operating expenses relative to increases in purchase price; A Manufacturer Analysis, which provides an estimate of manufacturers' response to the proposed standards. Their response is quantified by changes in several measures of financial performance for a firm. An Industry Impact Analysis shows financial and competitive impacts on the appliance industry. A Utility Analysis that measures the impacts of the altered energy-consumption patterns on electric utilities. A Environmental Effects analysis, which estimates changes in emissions of carbon dioxide, sulfur oxides, and nitrogen oxides, due to reduced energy consumption in the home and at the power plant. A Regulatory Impact Analysis collects the results of all the analyses into the net benefits and costs from a national perspective. 47 figs., 171 tabs. (JF)

Not Available

1990-12-01T23:59:59.000Z

147

ELECTRICAL SUPPORT SYSTEM DESCRIPTION DOCUMENT  

SciTech Connect (OSTI)

The purpose of this revision of the System Design Description (SDD) is to establish requirements that drive the design of the electrical support system and their bases to allow the design effort to proceed to License Application. This SDD is a living document that will be revised at strategic points as the design matures over time. This SDD identifies the requirements and describes the system design as they exist at this time, with emphasis on those attributes of the design provided to meet the requirements. This SDD has been developed to be an engineering tool for design control. Accordingly, the primary audience/users are design engineers. This type of SDD both ''leads'' and ''trails'' the design process. It leads the design process with regard to the flow down of upper tier requirements onto the system. Knowledge of these requirements is essential in performing the design process. The SDD trails the design with regard to the description of the system. The description provided in the SDD is a reflection of the results of the design process to date. Functional and operational requirements applicable to electrical support systems are obtained from the ''Project Functional and Operational Requirements'' (F&OR) (Siddoway 2003). Other requirements to support the design process have been taken from higher-level requirements documents such as the ''Project Design Criteria Document'' (PDC) (Doraswamy 2004), and fire hazards analyses. The above-mentioned low-level documents address ''Project Requirements Document'' (PRD) (Canon and Leitner 2003) requirements. This SDD contains several appendices that include supporting information. Appendix B lists key system charts, diagrams, drawings, and lists, and Appendix C includes a list of system procedures.

S. Roy

2004-06-24T23:59:59.000Z

148

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-4079-1 2. Government Accession No. 3 Austin, TX 78705-2650 11. Contract or Grant No. Technical Report 0-4079 13. Type of Report and Period in order to expedite the acquisition process, minimize cost, and build property owners' trust in government

Texas at Austin, University of

149

Forecast Technical Document Restocking in the Forecast  

E-Print Network [OSTI]

Forecast Technical Document Restocking in the Forecast A document describing how restocking of felled areas is handled in the 2011 Production Forecast. Tom Jenkins Robert Matthews Ewan Mackie Lesley in the forecast Background During the period of a production forecast it is assumed that, as forest sub

150

Forecast Technical Document Felling and Removals  

E-Print Network [OSTI]

Forecast Technical Document Felling and Removals Forecasts A document describing how volume fellings and removals are handled in the 2011 Production Forecast system. Tom Jenkins Robert Matthews Ewan Mackie Lesley Halsall #12;PF2011 ­ Felling and removals forecasts Background A fellings and removals

151

Forecast Technical Document Growing Stock Volume  

E-Print Network [OSTI]

Forecast Technical Document Growing Stock Volume Forecasts A document describing how growing stock (`standing') volume is handled in the 2011 Production Forecast. Tom Jenkins Robert Matthews Ewan Mackie Lesley Halsall #12;PF2011 ­ Growing stock volume forecasts Background A forecast of standing volume (or

152

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-07/0-5020-1 2. Government Accession No. 3 3208 Red River, Suite 200 Austin, TX 78705-2650 11. Contract or Grant No. 0-5020 13. Type of Report Documentation Page 1. Report No. FHWA/TX-07/0-5020-1 2. Government Accession No. 3. Recipient's Catalog No. 5

Texas at Austin, University of

153

Yucca Mountain Climate Technical Support Representative  

SciTech Connect (OSTI)

The primary objective of Project Activity ORD-FY04-012, “Yucca Mountain Climate Technical Support Representative,” was to provide the Office of Civilian Radioactive Waste Management (OCRWM) with expertise on past, present, and future climate scenarios and to support the technical elements of the Yucca Mountain Project (YMP) climate program. The Climate Technical Support Representative was to explain, defend, and interpret the YMP climate program to the various audiences during Site Recommendation and License Application. This technical support representative was to support DOE management in the preparation and review of documents, and to participate in comment response for the Final Environmental Impact Statement, the Site Recommendation Hearings, the NRC Sufficiency Comments, and other forums as designated by DOE management. Because the activity was terminated 12 months early and experience a 27% reduction in budget, it was not possible to complete all components of the tasks as originally envisioned. Activities not completed include the qualification of climate datasets and the production of a qualified technical report. The following final report is an unqualified summary of the activities that were completed given the reduced time and funding.

Sharpe, Saxon E

2007-10-23T23:59:59.000Z

154

Review of technical documents supporting proposed revisions to EPA (Environmental Protection Agency) regulations for the disposal/reuse of sewage sludge under Section 405(D) of the Clean Water Act. Final report  

SciTech Connect (OSTI)

In August 1985 the Environmental Engineering Committee of the Science Advisory Board was asked by the Office of Water Regulations and Standards (OWRS) to review technical documents supporting development of EPA regulations for the disposal/reuse of sewage sludge under Section 405(d) of the Clean Water Act. The Committee was also asked by the Office of Marine and Estuarine Protection (OMEP) to review technical documents supporting revisions of the EPA ocean dumping regulations. The Committee chose to review the two sets of documents together, since they both dealt with a common subject, and since they shared, in some respects, a common methodology. The report, however, covers only the review of the OWRS documents, which consist of a set of risk-assessment methodologies (1,2,3,4) for four sludge disposal/reuse options (landfilling, land application/distribution and marketing, incineration, and ocean disposal). The reviews of the OMEP documents are covered in separate Committee reports. The Committee's principal findings are outlined.

Not Available

1987-01-01T23:59:59.000Z

155

Scientific/Technical /Management Document Response to Solicitation: NNH13ZEA001N-SSAT: B.2 System-  

E-Print Network [OSTI]

Scientific/Technical /Management Document Response to Solicitation: NNH13ZEA001N-SSAT: B.2 System. Developing and documenting the evidence needed to support a claim requires diverse models and abstractions.................................................................................................................. 3 3. Scientific / Technical / Management

Spivak, David

156

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. SWUTC/13/600451-00073-1 2. Government Accession in both traditional internal combustion engine vehicles (ICEs) and electric vehicles (EVs) have a strong influence on transportation revenue by reducing fuel consumption per vehicle and ultimately drawing down

157

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. Preliminary Review Copy FHWA/TX-03/1833-01-imp-1 2. Government Accession No. 3. Recipient's Catalog No. 5. Report Date October 2002 4. Title Harrison Michael Bomba 8. Performing Organization Report No. 1833-01-imp-1 10. Work Unit No. (TRAIS)9

Texas at Austin, University of

158

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-0-4197-1 2. Government Accession No. 3 of Intelligent Transportation Systems 5. Report Date May 2001 6. Performing Organization Code7. Authors Tejas Mehta, Hani S. Mahmassani, and Chandra Bhat 8. Performing Organization Report No. 10. Work Unit No

Texas at Austin, University of

159

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-08/0-5708-1 2. Government Accession No. 3. Recipient's Catalog No. 4. Title and Subtitle Design of CrackScope (VCrack) [Reprint] 5. Report Date October Organization Report No. 0-5708-1 9. Performing Organization Name and Address Center for Transportation Research

Texas at Austin, University of

160

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Technical Report Documentation Page 1. Report No. FHWA/TX-09/0-5546-1 2. Government Accession No. 3 of Incompatible Uses 5. Report Date September 2007; Rev. January 2008 6. Performing Organization Code 7. Author(s) Lisa Loftus-Otway, C. Michael Walton, Lynn Blais, Nathan Hutson 8. Performing Organization Report No. 0

Texas at Austin, University of

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

FINAL COPY Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-4069-3 2. Government-Service Structures with Premature 5. Report Date October 2004, Rev. September 2005 Concrete Deterioration: Synthesis Report 6. Performing Organization Code 7. Author(s) 8. Performing Organization Report No. Amy E. Eskridge

Texas at Austin, University of

162

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

satellite coverage was poor. Both monitoring systems are evaluated in this report. 17. Key Words bridge No restrictions. This document is available to the public through the National Technical Information Service, Springfield, Virginia 22161. 19. Security Classif. (of report) Unclassified 20. Security Classif. (of

Texas at Austin, University of

163

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

. Key Words Prestressed Concrete Pavement (PCP), Special Specifications (SS), Nondestructive Testing Development of Post-Tension Prestressed Concrete Pavements in Texas. 16. Abstract This is the third technical of Post-Tensioned Prestressed Concrete Pavements in Texas." The contents of this document intend

Texas at Austin, University of

164

G1 Account: Guest Account Supporting Documentation  

E-Print Network [OSTI]

G1 Account: Guest Account Supporting Documentation Phone: 202-994-7900 Fax: 202-994-4747 Email: acadtech@gwu.edu Web: http://acadtech.gwu.edu Supporting Documentation: Based on your role, please provide the Special Account Request Form along with reservation documentation from the Office of Academic Scheduling

Vertes, Akos

165

Dose Modeling Evaluations and Technical Support Document for the Authorized Limits Request for the C-746-U Landfill at the Paducah Gaseous Diffusion Plant, Paducah, Kentucky  

SciTech Connect (OSTI)

This report contains the technical basis in support of the DOE?s derivation of Authorized Limits (ALs) for the DOE Paducah C-746-U Landfill. A complete description of the methodology, including an assessment of the input parameters, model inputs, and results is provided in this report. This report also provides initial recommendations on applying the derived soil guidelines. The ORISE-derived soil guidelines are specifically applicable to the Landfill at the end of its operational life. A suggested 'upper bound' multiple of the derived soil guidelines for individual shipments is provided.

Boerner, A. J. [IEAVP, ORISE, Oak Ridge, TN (United States); Maldonado, D. G. [IEAVP, ORISE, Oak Ridge, TN (United States; Hansen, Tom [Ameriphysics, LLC (United States)

2012-06-01T23:59:59.000Z

166

TECHNICAL BASIS FOR VENTILATION REQUIREMENTS IN TANK FARMS OPERATING SPECIFICATIONS DOCUMENTS  

SciTech Connect (OSTI)

This report provides the technical basis for high efficiency particulate air filter (HEPA) for Hanford tank farm ventilation systems (sometimes known as heating, ventilation and air conditioning [HVAC]) to support limits defined in Process Engineering Operating Specification Documents (OSDs). This technical basis included a review of older technical basis and provides clarifications, as necessary, to technical basis limit revisions or justification. This document provides an updated technical basis for tank farm ventilation systems related to Operation Specification Documents (OSDs) for double-shell tanks (DSTs), single-shell tanks (SSTs), double-contained receiver tanks (DCRTs), catch tanks, and various other miscellaneous facilities.

BERGLIN, E J

2003-06-23T23:59:59.000Z

167

Health Effects Support Document for Hexachlorobutadiene Health Effects Support Document  

E-Print Network [OSTI]

The Safe Drinking Water Act (SDWA), as amended in 1996, requires the Administrator of the Environmental Protection Agency (EPA) to establish a list of contaminants to aid the agency in regulatory priority setting for the drinking water program. In addition, SDWA requires EPA to make regulatory determinations for no fewer than five contaminants by August 2001. The criteria used to determine whether or not to regulate a chemical on the CCL are the following: The contaminant may have an adverse effect on the health of persons. The contaminant is known to occur or there is a substantial likelihood that the contaminant will occur in public water systems with a frequency and at levels of public health concern. In the sole judgment of the administrator, regulation of such contaminant presents a meaningful opportunity for health risk reduction for persons served by public water systems. The Agency’s findings for the three criteria are used in making a determination to regulate a contaminant. The Agency may determine that there is no need for regulation when a contaminant fails to meet one of the criteria. This document provides the health effects basis for the regulatory determination for hexachlorobutadiene. In arriving at the regulatory determination, data on toxicokinetics, human

For Hexachlorobutadiene

2003-01-01T23:59:59.000Z

168

ARM - Ingest Supporting Workflow Documentation  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcal Documentation(AVIRIS) ProductsAirborneOctober 11, 2011 [FacilityIndiaGVAXAssociated StatusWorkflow

169

Dose Modeling Evaluations and Technical Support Document For the Authorized Limits Request for the DOE-Owned Property Outside the Limited Area, Paducah Gaseous Diffusion Plant Paducah, Kentucky  

SciTech Connect (OSTI)

Environmental assessments and remediation activities are being conducted by the U.S. Department of Energy (DOE) at the Paducah Gaseous Diffusion Plant (PGDP), Paducah, Kentucky. The Oak Ridge Institute for Science and Education (ORISE), a DOE prime contractor, was contracted by the DOE Portsmouth/Paducah Project Office (DOE-PPPO) to conduct radiation dose modeling analyses and derive single radionuclide soil guidelines (soil guidelines) in support of the derivation of Authorized Limits (ALs) for 'DOE-Owned Property Outside the Limited Area' ('Property') at the PGDP. The ORISE evaluation specifically included the area identified by DOE restricted area postings (public use access restrictions) and areas licensed by DOE to the West Kentucky Wildlife Management Area (WKWMA). The licensed areas are available without restriction to the general public for a variety of (primarily) recreational uses. Relevant receptors impacting current and reasonably anticipated future use activities were evaluated. In support of soil guideline derivation, a Conceptual Site Model (CSM) was developed. The CSM listed radiation and contamination sources, release mechanisms, transport media, representative exposure pathways from residual radioactivity, and a total of three receptors (under present and future use scenarios). Plausible receptors included a Resident Farmer, Recreational User, and Wildlife Worker. single radionuclide soil guidelines (outputs specified by the software modeling code) were generated for three receptors and thirteen targeted radionuclides. These soil guidelines were based on satisfying the project dose constraints. For comparison, soil guidelines applicable to the basic radiation public dose limit of 100 mrem/yr were generated. Single radionuclide soil guidelines from the most limiting (restrictive) receptor based on a target dose constraint of 25 mrem/yr were then rounded and identified as the derived soil guidelines. An additional evaluation using the derived soil guidelines as inputs into the code was also performed to determine the maximum (peak) dose for all receptors. This report contains the technical basis in support of the DOE?s derivation of ALs for the 'Property.' A complete description of the methodology, including an assessment of the input parameters, model inputs, and results is provided in this report. This report also provides initial recommendations on applying the derived soil guidelines.

Boerner, A. J. [Oak Ridge Institute for Science and Education (ORISE), Oak Ridge, TN (United States). Independent Environmental Assessment and Verification Program; Maldonado, D. G. [Oak Ridge Institute for Science and Education (ORISE), Oak Ridge, TN (United States). Independent Environmental Assessment and Verification Program; Hansen, Tom [Ameriphysics, LLC (United States)

2012-09-01T23:59:59.000Z

170

2015-02-13 Issuance: Energy Conservation Standards for Portable Air Conditioners; Notice of Public Meeting and Availability of the Preliminary Technical Support Document  

Broader source: Energy.gov [DOE]

This document is a pre-publication Federal Register notice of public meeting regarding energy conservation standards for portable air conditioners, as issued by the Deputy Assistant Secretary for Energy Efficiency on February 13, 2015. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

171

RELEASE OF DRIED RADIOACTIVE WASTE MATERIALS TECHNICAL BASIS DOCUMENT  

SciTech Connect (OSTI)

This technical basis document was developed to support RPP-23429, Preliminary Documented Safety Analysis for the Demonstration Bulk Vitrification System (PDSA) and RPP-23479, Preliminary Documented Safety Analysis for the Contact-Handled Transuranic Mixed (CH-TRUM) Waste Facility. The main document describes the risk binning process and the technical basis for assigning risk bins to the representative accidents involving the release of dried radioactive waste materials from the Demonstration Bulk Vitrification System (DBVS) and to the associated represented hazardous conditions. Appendices D through F provide the technical basis for assigning risk bins to the representative dried waste release accident and associated represented hazardous conditions for the Contact-Handled Transuranic Mixed (CH-TRUM) Waste Packaging Unit (WPU). The risk binning process uses an evaluation of the frequency and consequence of a given representative accident or represented hazardous condition to determine the need for safety structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls. A representative accident or a represented hazardous condition is assigned to a risk bin based on the potential radiological and toxicological consequences to the public and the collocated worker. Note that the risk binning process is not applied to facility workers because credible hazardous conditions with the potential for significant facility worker consequences are considered for safety-significant SSCs and/or TSR-level controls regardless of their estimated frequency. The controls for protection of the facility workers are described in RPP-23429 and RPP-23479. Determination of the need for safety-class SSCs was performed in accordance with DOE-STD-3009-94, Preparation Guide for US. Department of Energy Nonreactor Nuclear Facility Documented Safety Analyses, as described below.

KOZLOWSKI, S.D.

2007-05-30T23:59:59.000Z

172

Hanford site solid waste management environmental impact statement technical information document [SEC 1 THRU 4  

SciTech Connect (OSTI)

This Technical Information Document (TID) provides engineering data to support DOE/EIS-0286, ''Hanford Site Solid (Radioactive and Hazardous) Waste Program Environmental Impact Statement,'' including assumptions and waste volumes calculation data.

FRITZ, L.L.

2003-04-01T23:59:59.000Z

173

SUPPORTING COLLABORATIVE WRITING OF XML DOCUMENTS  

E-Print Network [OSTI]

SUPPORTING COLLABORATIVE WRITING OF XML DOCUMENTS G´erald Oster, Hala Skaf-Molli, Pascal Molli: Data management is a key issue in cooperative systems. Anyone who uses more than one computer or collab- orates with other people is aware of the problems posed by having multiple copies of shared documents

Boyer, Edmond

174

Technical support document: Energy efficiency standards for consumer products: Room air conditioners, water heaters, direct heating equipment, mobile home furnaces, kitchen ranges and ovens, pool heaters, fluorescent lamp ballasts and television sets. Volume 1, Methodology  

SciTech Connect (OSTI)

The Energy Policy and Conservation Act (P.L. 94-163), as amended, establishes energy conservation standards for 12 of the 13 types of consumer products specifically covered by the Act. The legislation requires the Department of Energy (DOE) to consider new or amended standards for these and other types of products at specified times. DOE is currently considering amending standards for seven types of products: water heaters, direct heating equipment, mobile home furnaces, pool heaters, room air conditioners, kitchen ranges and ovens (including microwave ovens), and fluorescent light ballasts and is considering establishing standards for television sets. This Technical Support Document presents the methodology, data, and results from the analysis of the energy and economic impacts of the proposed standards. This volume presents a general description of the analytic approach, including the structure of the major models.

Not Available

1993-11-01T23:59:59.000Z

175

Technical support document: Energy efficiency standards for consumer products: Refrigerators, refrigerator-freezers, and freezers including draft environmental assessment, regulatory impact analysis  

SciTech Connect (OSTI)

The Energy Policy and Conservation Act (P.L. 94-163), as amended by the National Appliance Energy Conservation Act of 1987 (P.L. 100-12) and by the National Appliance Energy Conservation Amendments of 1988 (P.L. 100-357), and by the Energy Policy Act of 1992 (P.L. 102-486), provides energy conservation standards for 12 of the 13 types of consumer products` covered by the Act, and authorizes the Secretary of Energy to prescribe amended or new energy standards for each type (or class) of covered product. The assessment of the proposed standards for refrigerators, refrigerator-freezers, and freezers presented in this document is designed to evaluate their economic impacts according to the criteria in the Act. It includes an engineering analysis of the cost and performance of design options to improve the efficiency of the products; forecasts of the number and average efficiency of products sold, the amount of energy the products will consume, and their prices and operating expenses; a determination of change in investment, revenues, and costs to manufacturers of the products; a calculation of the costs and benefits to consumers, electric utilities, and the nation as a whole; and an assessment of the environmental impacts of the proposed standards.

NONE

1995-07-01T23:59:59.000Z

176

KMi Technical Report Contextually-enriched Documents  

E-Print Network [OSTI]

-enriched Documents: Publishing for Organizational Learning Marek Hatala Knowledge Media Institute The Open University of organizational learning. Building on the Digital Document Discourse Environment (D3E) we have developed tools Knowledge, Ontologies, Organizational Learning, Digital Documents, Electronic Publishing, Hypertext, World

177

CRAD, New Nuclear Facility Documented Safety Analysis and Technical...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Technical Safety Requirements - December 2, 2014 (EA CRAD 31-07, Rev. 0) More Documents & Publications CRAD, Nuclear Reactor Facility Operations - December 4, 2014 (EA CRAD 31-08...

178

TECHNICAL SUPPORT DOCUMENT: ENERGY CONSERVATION STANDARDS FOR...  

Broader source: Energy.gov (indexed) [DOE]

design measure than the levels ana The proposed efficiency standards will decrease air pollution b future energy demand. The greatest decreases in air pollution will oxides...

179

Technical Support Document: Energy Conservation Standards for  

Broader source: Energy.gov (indexed) [DOE]

decrease air pollu- tion by decreasing future energy demand. The greatest decreases in air pollution , will be in sulfur oxides (listed in equivalent weight of sulfur dioxide,...

180

Enclosure 3 TECHNICAL AND REGULATORY SUPPORT DOCUMENT  

E-Print Network [OSTI]

....................................................................................................30 d. Equivalent QA Program........................................................................................................................25 6. Implementation of Characterization Methodologies to Satisfy DQOs................................................................................................31 III. EPA'S ANALYSIS OF DOE'S PROPOSED RH PROGRAM

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

ATVM Technical Support Document | Department of Energy  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energyon ArmedWaste and Materials2014Energy

182

Supporting Technical Documents | Department of Energy  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of Energy Power.pdf11-161-LNGInternational EnergyCommittee onGASRaineyEnergyEXC-14-0002 | Department

183

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

transportation technologies including connected vehicles, autonomous vehicles, electric systems, and cloud of new technologies. 17. Key Words Transportation Technology, Autonomous Vehicles, Connected Vehicles Vehicles 18. Distribution Statement No restrictions. This document is available to the public through

184

Efficient Complex Query Support for Multiversion XML Documents  

E-Print Network [OSTI]

management system supporting multiple versions of the same document, while avoiding duplicate storage taken by database systems and document management systems have often been different, because complex queries, while document management systems are not, and ­ Databases assume that the order

Zhang, Donghui

185

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

problems associated with using a global positioning system (GPS) with real-time, satellite is available to the public through the National Technical Information Service, Springfield, Virginia 22161. 19. Security Classif. (of report) Unclassified 20. Security Classif. (of this page) Unclassified 21. No

Texas at Austin, University of

186

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

, topographical and satellite aerial maps to assist with the identification of the project extents. Once TRMs through the National Technical Information Service, Springfield, Virginia 22161; www.ntis.gov. 19. Security Classif. (of report) Unclassified 20. Security Classif. (of this page) Unclassified 21. No

Texas at Austin, University of

187

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

is available to the public through NTIS: National Technical Information Service 5285 Port Royal Road techniques are used to solve the problems. Demand for PEVs is increasing with the growing concerns about environment pollution, energy resources, and the economy. However, battery capacity in PEVs is still limited

188

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

and metropolitan areas. Economists have also predicted that oil prices will rise in real terms during the same: National Technical Information Service 5285 Port Royal Road Springfield, Virginia 22161 19. Security Classif. (of this report) Unclassified 20. Security Classif. (of this page) Unclassified 21. No. of Pages

189

Bulletin #10 September 26, 2003 Management and Support Documentation for  

E-Print Network [OSTI]

A CALL TO Bulletin #10 September 26, 2003 Management and Support Documentation for UW Foundation..................................1 Records retention..........................................2 GUIDANCE ON THE MANAGEMENT AND SUPPORT DOCUMENTATION FOR UW FOUNDATION RECEIPTS AND EXPENDITURES INTRODUCTION Campus departments

Sheridan, Jennifer

190

Technical Support and Transfer of Geothrmal Technical Knowledge and Information  

SciTech Connect (OSTI)

The Geo-Heat Center (GHC) staff provided responses to 1442 technical support requests during the contract period (April 1, 2006 to September 30, 2007), which were six quarters under this contract. Our website, consisting of 1900 files, also contributes to our technical assistance activity. Downloaded files were 1,889,323 (3,448 per day) from our website, the total number of users was 1,365,258 (2,491 per day), and the total number of hits were 6,008,500 (10,064 per day). The GHC staff attended 60 workshops, short course and professional meeting and made 29 technical presentations. The staff also prepared and mailed out 2,000 copies of each of five issues of the GHC Quaterly Bulletin which contained 26 articles. We also mailed out approximately 5,000 papers and publications to interested individuals and organizations.

John W. Lund

2007-11-14T23:59:59.000Z

191

DOE Awards Small Business Task Order for Technical Support to...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Contract Awarded to Small Business for Support Services DOE Awards Support Service Contract DOE Awards Small Business Task Order for Technical Support to the Office of...

192

Technical background document for draft soil screening level guidance  

SciTech Connect (OSTI)

The document provides technical details of the derivation of the September 30, 1993, draft Soil Screening Levels (SSLs) Guidance for Superfund (PB93-963508). The document is presented in two sections. Section I defines SSL and provides background information on the development of SSLs and their application and implementation at Superfund sites, including sampling schemes for measuring SSL attainment. It also provides draft SSLs developed for 30 chemicals. Section II provides the technical basis for the development of SSLs addressing direct ingestion of soil, inhalation of volatiles and fugitive dust, and the soil-to-ground-water exposure pathway, including the assumptions and theories used the their development.

Not Available

1994-03-01T23:59:59.000Z

193

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

, and to ensure it continues to flourish, we must build a future based on sustainable growth principles. Our Texas Transportation Institute Texas A&M University System College Station, Texas 77843-3135 11 College Station, Texas 77843-3135 14. Sponsoring Agency Code 15. Supplementary Notes Supported by general

194

Technical Documentation for System Center 2012 Virtual Machine  

E-Print Network [OSTI]

#12; Technical Documentation for System Center 2012 ­ Virtual Machine Manager VMM Information Experience Team Summary: Virtual Machine Manager (VMM) is a management solution resources in order to create and deploy virtual machines and services to private clouds that you have

Hunt, Galen

195

DOE Awards Small Business Task Order for Technical Support to...  

Office of Environmental Management (EM)

nuclear energy research. Addthis Related Articles DOE Awards Support Service Contract DOE Awards Small Business Task Order for Technical Support to the Office of...

196

Technical Assessment Team (TAT) Supporting Technical Documents | Department  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of Energy Power.pdf11-161-LNGInternational EnergyCommitteeRenewable1234 OFTechnetium Retentionof Energy

197

Methodology and assumptions for evaluating heating and cooling energy requirements in new single-family residential buildings: Technical support document for the PEAR (Program for Energy Analysis of Residences) microcomputer program  

SciTech Connect (OSTI)

This report provides technical documentation for a software package called PEAR (Program for Energy Analysis of Residences) developed by LBL. PEAR offers an easy-to-use and accurate method of estimating the energy savings associated with various energy conservation measures used in site-built, single-family homes. This program was designed for use by non-technical groups such as home builders, home buyers or others in the buildings industry, and developed as an integral part of a set of voluntary guidelines entitled Affordable Housing Through Energy Conservation: A Guide to Designing and Constructing Energy Efficient Homes. These guidelines provide a method for selecting and evaluating cost-effective energy conservation measures based on the energy savings estimated by PEAR. This work is part of a Department of Energy program aimed at conducting research that will improve the energy efficiency of the nation's stock of conventionally-built and manufactured homes, and presenting the results to the public in a simplified format.

Huang, Y.J.; Ritschard, R.; Bull, J.; Byrne, S.; Turiel, I.; Wilson, D.; Hsui, C.; Foley, D.

1987-01-01T23:59:59.000Z

198

Technical Basis Document for PFP Area Monitoring Dosimetry Program  

SciTech Connect (OSTI)

This document describes the phantom dosimetry used for the PFP Area Monitoring program and establishes the basis for the Plutonium Finishing Plant's (PFP) area monitoring dosimetry program in accordance with the following requirements: Title 10, Code of Federal Regulations (CFR), part 835, ''Occupational Radiation Protection'' Part 835.403; Hanford Site Radiological Control Manual (HSRCM-1), Part 514; HNF-PRO-382, Area Dosimetry Program; and PNL-MA-842, Hanford External Dosimetry Technical Basis Manual.

COOPER, J.R.

2000-04-17T23:59:59.000Z

199

All Active DOE Technical Standards Document | Department of Energy  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of EnergyEnergy Cooperation |South42.2 (April 2012) 1 Documentation and Approval ofAll Active DOE Technical

200

DOE Awards Small Business Contract for Technical Support to the...  

Office of Environmental Management (EM)

LLC of Idaho Falls, Idaho to provide technical support to the Office of Environmental Management. A time & materials task order will be issued from the master Indefinite...

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Spent Nuclear Fuel Project technical baseline document. Fiscal year 1995: Volume 1, Baseline description  

SciTech Connect (OSTI)

This document is a revision to WHC-SD-SNF-SD-002, and is issued to support the individual projects that make up the Spent Nuclear Fuel Project in the lower-tier functions, requirements, interfaces, and technical baseline items. It presents results of engineering analyses since Sept. 1994. The mission of the SNFP on the Hanford site is to provide safety, economic, environmentally sound management of Hanford SNF in a manner that stages it to final disposition. This particularly involves K Basin fuel, although other SNF is involved also.

Womack, J.C. [Westinghouse Hanford Co., Richland, WA (United States); Cramond, R. [TRW (United States); Paedon, R.J. [SAIC (United States)] [and others

1995-03-13T23:59:59.000Z

202

Technical Issues Map for the NHI System Interface and Support Systems Area: 1st Quarter FY 07  

SciTech Connect (OSTI)

This document provides a mapping of technical issues associated with development of the Next Generation Nuclear Plant (NGNP) intermediate heat transport loop and nuclear hydrogen plant support systems to the work that has been accomplished or is currently underway. The technical issues are ranked according to priority and by assumed resolution dates. Due to funding limitations, not all high-priority technical issues are under study at the present time, and more resources will need to be dedicated to tackling such issues in the future. This technical issues map is useful for understanding the relative importance of various technical challenges and will be used as a planning tool for future work package planning.

Steven R. Sherman

2006-12-01T23:59:59.000Z

203

PHOTOS Interface in C++; Technical and Physics Documentation  

E-Print Network [OSTI]

The first version of PHOTOS Monte Carlo for bremsstrahlung in the decay of particles and resonances with an interface to the HepMC event record written in C++ is now available. The main purpose of the present paper is to document technical aspects of the PHOTOS Monte Carlo installation and its use. A multitude of test results and examples are distributed together with the program code. The PHOTOS C++ physics precision is now as good as that of its FORTRAN predecessor. Howeverbetter steering options are available. An algorithm of the event record interface is prepared for the installation of process dependent variants of the photon emission kernel. Weights, featuring complete first order matrix elements, can be installed for general use. In the FORTRAN version of PHOTOS they were available only for decays of particles at rest and with spin set along the z axis. Physics assumptions used in the program and properties of the solution it offers are reviewed. In particular, it is mentioned that the second order matrix elements were used in design and validation of the program iteration procedure. Also it is explained that the phase space parameterization used in the program is exact.

N. Davidson; T. Przedzinski; Z. Was

2010-11-03T23:59:59.000Z

204

Technology status in support of refined technical baseline for the Spent Nuclear Fuel project. Revision 1  

SciTech Connect (OSTI)

The Spent Nuclear Fuel Project (SNFP) has undertaken technology acquisition activities focused on supporting the technical basis for the removal of the N Reactor fuel from the K Basins to an interim storage facility. The purpose of these technology acquisition activities has been to identify technology issues impacting design or safety approval, to establish the strategy for obtaining the necessary information through either existing project activities, or the assignment of new work. A set of specific path options has been identified for each major action proposed for placing the N Reactor fuel into a ``stabilized`` form for interim storage as part of this refined technical basis. This report summarizes the status of technology information acquisition as it relates to key decisions impacting the selection of specific path options. The following specific categories were chosen to characterize and partition the technology information status: hydride issues and ignition, corrosion, hydrogen generation, drying and conditioning, thermal performance, criticality and materials accountability, canister/fuel particulate behavior, and MCO integrity. This report represents a preliminary assessment of the technology information supporting the SNFP. As our understanding of the N Reactor fuel performance develops the technology information supporting the SNFP will be updated and documented in later revisions to this report. Revision 1 represents the incorporation of peer review comments into the original document. The substantive evolution in our understanding of the technical status for the SNFP (except section 3) since July 1995 have not been incorporated into this revision.

Puigh, R.J.; Toffer, H.; Heard, F.J.; Irvin, J.J.; Cooper, T.D.

1995-10-20T23:59:59.000Z

205

Technical Issues Map for the NHI System Interface and Support Systems Area: 2nd Quarter FY07  

SciTech Connect (OSTI)

This document provides a mapping of technical issues associated with development of the Next Generation Nuclear Plant (NGNP) intermediate heat transport loop and nuclear hydrogen plant support systems to the work that has been accomplished or is currently underway in the 2nd quarter of FY07.

Steven R. Sherman

2007-03-01T23:59:59.000Z

206

Grocery Store 50% Energy Savings Technical Support Document 2009 | Open  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to: navigation,Ohio:Greer County is a county in Oklahoma. ItsGrid2HomeSavings50%Energy

207

DOCKET NO: A-98-49 TECHNICAL SUPPORT DOCUMENT FOR  

E-Print Network [OSTI]

...............................................................................................................14 2.2.1 Hanford Site CRA Data Assembly

208

Department of Energy Technical Support Document National Environmental  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of Inspector General Office of Audit Services Audit ReportNextConditional LoanEnergyMattoon, IllinoisPolicy

209

General Merchandise 50% Energy Savings Technical Support Document 2009 |  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to: navigation, searchGeauga County, Ohio: Energy ResourcesEnergy InformationOpen

210

Fluor Hanford, Inc. Groundwater and Technical Integration Support (Master Project) Quality Assurance Management Plan  

SciTech Connect (OSTI)

The scope of the Fluor Hanford, Inc. Groundwater and Technical Integration Support (Master Project) is to provide technical and integration support to Fluor Hanford, Inc., including operable unit investigations at 300-FF-5 and other groundwater operable units, strategic integration, technical integration and assessments, remediation decision support, and science and technology. This Quality Assurance Management Plan provides the quality assurance requirements and processes that will be followed by the Fluor Hanford, Inc. Groundwater and Technical Integration Support (Master Project).

Fix, N. J.

2008-02-20T23:59:59.000Z

211

Technical resource document for assured thermal processing of wastes  

SciTech Connect (OSTI)

This document is a concise compendium of resource material covering assured thermal processing of wastes (ATPW), an area in which Sandia aims to develop a large program. The ATPW program at Sandia is examining a wide variety of waste streams and thermal processes. Waste streams under consideration include municipal, chemical, medical, and mixed wastes. Thermal processes under consideration range from various incineration technologies to non-incineration processes such as supercritical water oxidation or molten metal technologies. Each of the chapters describes the element covered, discusses issues associated with its further development and/or utilization, presents Sandia capabilities that address these issues, and indicates important connections to other ATPW elements. The division of the field into elements was driven by the team`s desire to emphasize areas where Sandia`s capabilities can lead to major advances and is therefore somewhat unconventional. The report will be valuable to Sandians involved in further ATPW program development.

Farrow, R.L.; Fisk, G.A.; Hartwig, C.M.; Hurt, R.H.; Ringland, J.T.; Swansiger, W.A.

1994-06-01T23:59:59.000Z

212

TECHNICAL BASIS DOCUMENT FOR AT-POWER SIGNIFICANCE DETERMINATION PROCESS (SDP) NOTEBOOKS.  

SciTech Connect (OSTI)

To support the assessment of inspection findings as part of the risk-informed inspection in the United States Nuclear Regulatory Commission's (USNRC's) Reactor Oversight Process (ROP), risk inspection notebooks, also called significance determination process (SDP) notebooks, have been developed for each of the operating plants in the United States. These notebooks serve as a tool for assessing risk significance of inspection findings along with providing an engineering understanding of the significance. Plant-specific notebooks are developed to capture plant-specific features, characteristics, and analyses that influence the risk profile of the plant. At the same time, the notebooks follow a consistent set of assumptions and guidelines to assure consistent treatment of inspection findings across the plants. To achieve these objectives, notebooks are designed to provide specific information that are unique both in the manner in which the information is provided and in the way the screening risk assessment is carried out using the information provided. The unique features of the SDP notebooks, the approaches used to present the information for assessment of inspection findings, the assumptions used in consistent modeling across different plants with due credit to plant-specific features and analyses form the technical basis of the SDP notebooks. In this document, the unique features and the technical basis for the notebooks are presented. The types of information that are included and the reasoning/basis for including that information are discussed. The rules and basis for developing the worksheets that are used by the inspectors in the assessment of inspection findings are presented. The approach to modeling plants' responses to different initiating events and specific assumptions/considerations used for each of the reactor types are also discussed.

AZARM,M.A.SMANTA,P.K.MARTINEZ-GURIDI,G.HIGGINS,J.

2004-06-01T23:59:59.000Z

213

State energy price system. Volume I: overview and technical documentation  

SciTech Connect (OSTI)

This study utilizes existing data sources and previous analyses of state-level energy prices to develop consistent state-level energy prices series by fuel type and by end-use sector. The fuels are electricity, natural gas, coal, distillate fuel oil, motor gasoline, diesel, kerosene, jet fuel, residual fuel, and liquefied petroleum gas. The end-use sectors are residential, commercial, industrial, transportation, and electric utility. Based upon an evaluation of existing data sources, recommendations were formulated on the feasible approaches for developing a consistent state energy price series. The data series were compiled based upon the approaches approved after a formal EIA review. Detailed documentation was provided, including annual updating procedures. Recommendations were formulated for future improvements in the collection of data or in data processing. Generally, the geographical coverage includes the 50 states and the District of Columbia. Information on state-level energy use was generally taken from the State Energy Data System (SEDS). Corresponding average US prices are also developed using volumes reported in SEDS. To the extent possible, the prices developed are quantity weighted average retail prices. Both a Btu price series and a physical unit price series are developed for each fuel. The period covered by the data series is 1970 through 1980 for most fuels, though prices for electricity and natural gas extend back to 1960. (PSB)

Fang, J.M.; Nieves, L.A.; Sherman, K.L.; Hood, L.J.

1982-06-01T23:59:59.000Z

214

A New Technique For Information Processing of CLIC Technical Documentation  

E-Print Network [OSTI]

The scientific work presented in this paper could be described as a novel, systemic approach to the process of organization of CLIC documentation. The latter refers to the processing of various sets of archived data found on various CERN archiving services in a more friendly and organized way. From physics aspect, this is equal to having an initial system characterized by high entropy, which after some transformation of energy and matter will produce a final system of reduced entropy. However, this reduction in entropy can be considered valid for open systems only, which are sub-systems of grander isolated systems, to which the total entropy will always increase. Thus, using as basis elements from information theory, systems theory and thermodynamics, the unorganized form of data pending to be organized to a higher form, is modeled as an initial open sub-system with increased entropy, which, after the processing of information, will produce a final system with decreased entropy. This systemic approach to the ...

Tzermpinos, Konstantinos

2013-01-01T23:59:59.000Z

215

Light Water Reactor Sustainability Technical Documents | Department of  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |EnergyonSupport0.pdf5 OPAM SEMIANNUAL REPORT TOJaredKansas1 -Energy Initiatives »

216

Technical support document: Energy efficiency standards for consumer products: Room air conditioners, water heaters, direct heating equipment, mobile home furnaces, kitchen ranges and ovens, pool heaters, fluorescent lamp ballasts and television sets. Volume 2, Fluorescent lamp ballasts, television sets, room air conditioners, and kitchen ranges and ovens  

SciTech Connect (OSTI)

This document is divided into ``volumes`` B through E, dealing with individual classes of consumer products. Chapters in each present engineering analysis, base case forecasts, projected national impacts of standards, life-cycle costs and payback periods, impacts on manufacturers, impacts of standards on electric utilities, and environmental effects. Supporting appendices are included.

Not Available

1993-11-01T23:59:59.000Z

217

The Oak Ridge Technical Information Center: A trailblazer in federal documentation  

SciTech Connect (OSTI)

This document attempts to record the history of US AEC`s Technical Information Center, from its conception (1947) to 1977. This organization centralizes and manages the issues related to control and dissemination of technical information, to fulfill the provisions of the Atomic Energy Act of 1946. TIC tried to search out and install efficient and economical systems for servicing the various technical information programs. It coordinated a direct organization-to-organization information exchange program, and it also participated in official bilateral exchange programs and in developing information systems for IAEA and Euratom. The work, planning, and strategies employed to achieve goals are chronicled in this document, with 18 chapters arranged into four sections according to different presidential administrations.

Vaden, W.M.

1992-01-01T23:59:59.000Z

218

(Technical and engineering support for the Office of Industrial Programs)  

SciTech Connect (OSTI)

As of April 19, 1991, technical, operational and analytic support and assistance to the offices and divisions of the Office of Renewable Energy, under contract DE-AC01-86CE30844 was completed. The overall work effort, initiated February 20, 1986, was characterized by timely, comprehensive, high quality, professional responsiveness to a broad range of renewable energy program operational support requirements. These are no instances of failure to respond, nor unacceptable response, during the five-year period. The technology program areas covered are Solar Buildings Technology, Wind Energy Technology, Photovoltaic Energy Technology, Geothermal Energy Technology, Biofuels and Municipal Waste Technology, Solar Thermal Technology, Hydropower Energy Technology, Ocean Energy Technology, and Electric Energy Systems and Energy Storage. The analytical and managerial support provided to the office and staff of the Deputy Assistant Secretary for Renewable Energy enabled a comprehensive evaluation of program and policy alternatives, and the selection and execution of appropriate courses of action from amongst those alternatives. Largely through these means the Office has been able to maintain continuity and a meaningful program thrust through the vacillations of policies and budgets that it has experienced over that it has experienced over the past five years. Appended are summaries of support activities within each of the individual technology program areas, as well as a complete listing of all project deliverables and due-dates for each submittal under the contract.

Not Available

1991-01-01T23:59:59.000Z

219

Using Text Animated Transitions to Support Navigation in Document Histories  

E-Print Network [OSTI]

of an animated transition between two revisions of the Wikipedia article User interfaces. ABSTRACT This article examines the benefits of using text animated transitions for navigating in the revision history of textual documents. We propose an animation technique for smoothly transitioning between different text revisions

Toronto, University of

220

Hanford Waste Vitrification Plant technical background document for best available radionuclide control technology demonstration  

SciTech Connect (OSTI)

This report provides the background documentation to support applications for approval to construct and operate new radionuclide emission sources at the Hanford Waste Vitrification Plant (HWVP) near Richland, Washington. The HWVP is required to obtain permits under federal and state statutes for atmospheric discharges of radionuclides. Since these permits must be issued prior to construction of the facility, draft permit applications are being prepared, as well as documentation to support these permits. This report addresses the applicable requirements and demonstrates that the preferred design meets energy, environmental, and economic criteria for Best Available Radionuclide Control Technology (BARCT) at HWVP. 22 refs., 11 figs., 25 tabs.

Carpenter, A.B.; Skone, S.S.; Rodenhizer, D.G.; Marusich, M.V. (Ebasco Services, Inc., Bellevue, WA (USA))

1990-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

DOE Selects 8(a) Small Business for Technical Support Services...  

Office of Environmental Management (EM)

Support Cleanup of New York West Valley Demonstration Project DOE Awards Support Service Contract DOE Awards Small Business Contract for Support, Planning Services to Office of...

222

The CHPRC Groundwater and Technical Integration Support (Master Project) Quality Assurance Management Plan  

SciTech Connect (OSTI)

The scope of the CH2M Hill Plateau Remediation Company, LLC (CHPRC) Groundwater and Technical Integration Support (Master Project) is for Pacific Northwest National Laboratory staff to provide technical and integration support to CHPRC. This work includes conducting investigations at the 300-FF-5 Operable Unit and other groundwater operable units, and providing strategic integration, technical integration and assessments, remediation decision support, and science and technology. The projects under this Master Project will be defined and included within the Master Project throughout the fiscal year, and will be incorporated into the Master Project Plan. This Quality Assurance Management Plan provides the quality assurance requirements and processes that will be followed by the CHPRC Groundwater and Technical Integration Support (Master Project) and all releases associated with the CHPRC Soil and Groundwater Remediation Project. The plan is designed to be used exclusively by project staff.

Fix, N. J.

2009-04-03T23:59:59.000Z

223

Supporting document for the historical tank content estimate for BY-Tank farm  

SciTech Connect (OSTI)

This Supporting Document provides historical in-depth characterization information on BY-Tank Farm, such as historical waste transfer and level data, tank physical information,temperature plots, liquid observation well plots, chemical analyte and radionuclide inventories for the Historical Tank Content Estimate Report for the northeast quadrant of the Hanford 200 East Area.

Brevick, C.H.

1996-06-28T23:59:59.000Z

224

Supporting document for the historical tank content estimate for the SX-tank farm  

SciTech Connect (OSTI)

This Supporting Document provides historical in-depth characterization information on SX-Tank Farm, such as historical waste transfer and level data, tank physical information, temperature plots, liquid observation well plots, chemical analyte and radionuclide inventories for the Historical Tank Content Estimate Report for the Southwest Quadrant of the Hanford 200 West Area.

Brevick, C.H., Fluor Daniel Hanford

1997-02-25T23:59:59.000Z

225

Supporting document for the historical tank content estimate for the S-tank farm  

SciTech Connect (OSTI)

This Supporting Document provides historical in-depth characterization information on S-Tank Farm, such as historical waste transfer and level data, tank physical information, temperature plots, liquid observation well plots, chemical analyte and radionuclide inventories for the Historical Tank Content Estimate Report for the Southwest Quadrant of the Hanford 200 West Area.

Brevick, C.H., Fluor Daniel Hanford

1997-02-25T23:59:59.000Z

226

Supporting document for the historical tank content estimate for AW-tank farm  

SciTech Connect (OSTI)

This Supporting Document provides historical in-depth characterization information on AW-Tank Farm, such as historical waste transfer and level data, tank physical information, temperature plots, liquid observation well plots, chemical analyte and radionuclide inventories for the Historical Tank Content Estimate Report for the Southeast Quadrant of the Hanford 200 Areas.

Brevick, C.H., Stroup, J.L.; Funk, J.W., Fluor Daniel Hanford

1997-03-06T23:59:59.000Z

227

Supporting document for the historical tank content estimate for AP-tank farm  

SciTech Connect (OSTI)

This Supporting Document provides historical in-depth characterization information on AP-Tank Farm, such as historical waste transfer and level data, tank physical information, temperature plots, liquid observation well plots, chemical analyte and radionuclide inventories for the Historical Tank Content Estimate Report for the Southeast Quadrant of the Hanford 200 Areas.

Brevick, C.H.; Stroup, J.L.; Funk, J.W., Fluor Daniel Hanford

1997-03-06T23:59:59.000Z

228

Supporting document for the historical tank content estimate for AN-tank farm  

SciTech Connect (OSTI)

This Supporting Document provides historical in-depth characterization information on AN-Tank Farm, such as historical waste transfer and level data, tank physical information, temperature plots, liquid observation well plots, chemical analyte and radionuclide inventories for the Historical Tank Content Estimate Report for the Southeast Quadrant of the Hanford 200 Areas.

Brevick, C.H.; Stroup, J.L.; Funk, J.W., Fluor Daniel Hanford

1997-03-06T23:59:59.000Z

229

Supporting document for the historical tank content estimate for AY-tank farm  

SciTech Connect (OSTI)

This Supporting Document provides historical in-depth characterization information on AY-Tank Farm, such as historical waste transfer and level data, tank physical information, temperature plots, liquid observation well plots, chemical analyte and radionuclide inventories for the Historical Tank Content Estimate Report for the Southeast Quadrant of the Hanford 200 Areas.

Brevick, C.H.; Stroup, J.L.; Funk, J.W., Fluor Daniel Hanford, Fluor Daniel Hanford

1997-03-12T23:59:59.000Z

230

High-Btu gas from peat. A feasibility study. Task 11. Technical support. Final report  

SciTech Connect (OSTI)

In September 1980, the US Department of Energy awarded grant No. DE-FG01-80RA50348 to the Minnesota Gas Company (Minnegasco) to evaluate the commercial viability - technical, economic and environmental - of producing 80 million SCF/day of substitute natural gas (SNG) from peat. Minnegasco's project team for this study consisted of Dravo Engineers and Constructors (for design, engineering and economics of peat harvesting, dewatering and gasification systems); Ertec, Inc. (for environmental and socioeconomic analyses); Institute of Gas Technology (for gasification process information, and technical and engineering support). This report presents the work conducted under Task II (Technical Support) by the Institute of Gas Technology (IGT), the developer of the PEATGAS process, which was selected for the study. Task achievements are presented for: gasifier design and performance; technical support; and task management. 12 figures, 22 tables.

Not Available

1982-05-01T23:59:59.000Z

231

document  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

to Document 07123.04.Final Page 28 the surface during pipe connections with conventional rotary rigs. A major contribution of fast drilling and less rig time for CT drilling is...

232

NREL: Technology Deployment - Project Technical Assistance and Support  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the Contributions andData and ResourcesOther Federal Agency Support Photo of

233

Residential Energy Code Technical Support: Training that Works for Enforcement Personnel  

E-Print Network [OSTI]

RESIDENTIAL ENERGY CODE TECHNICAL SUPPORT: TRAINING THAT WORKS FOR ENFORCEMENT PERSONNEL JIM BOWMAN Washlngton State Energy Offlce 01 ympia. Washlngton Compiehenslve enforcement of resldentlal state energy codes depends upon well designed... of the more active bulldlng areas such as Tacoma. Spokane. and Spokane County. Provldlng adequate technlcal support to code enforcement personnel is an Important element In el evatl ng energy code enforcement levels. Two of the programs that have been...

Bowman, J.

1988-01-01T23:59:59.000Z

234

1E Wind Energy Program: Technical Information and Outreach Support Final Technical Report  

SciTech Connect (OSTI)

A U.S. consensus-based collaborative formed in 1994, the National Wind Coordinating Committee (NWCC) identifies issues that affect the use of wind power, establishes dialogue among key stakeholders, and catalyzes appropriate activities to support the development of environmentally, economically, and politically sustainable commercial markets for wind power. NWCC members include representatives from electric utilities and support organizations, state legislatures, state utility commissions, consumer advocacy offices, wind equipment suppliers and developers, green power marketers, environmental organizations, agriculture and economic development organizations, and state and federal agencies.

Arnold, Abigail

2006-03-09T23:59:59.000Z

235

Document  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc DocumentationP-Series to UserProduct:Directives Templates The OfficeDitchDivya401 Federal

236

Document  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc DocumentationP-Series to UserProduct:Directives Templates The OfficeDitchDivya401 Federal3623

237

Technical support document: Energy efficiency standards for consumer products: Room air conditioners, water heaters, direct heating equipment, mobile home furnaces, kitchen ranges and ovens, pool heaters, fluorescent lamp ballasts and television sets. Volume 3, Water heaters, pool heaters, direct heating equipment, and mobile home furnaces  

SciTech Connect (OSTI)

This is Volume 3 in a series of documents on energy efficiency of consumer products. This volume discusses energy efficiency of water heaters. Water heaters are defined by NAECA as products that utilize oil, gas, or electricity to heat potable water for use outside the heater upon demand. These are major appliances, which use a large portion (18% on average) of total energy consumed per household (1). They differ from most other appliances in that they are usually installed in obscure locations as part of the plumbing and are ignored until they fail. Residential water heaters are capable of heating water up to 180{degrees}F, although the setpoints are usually set lower.

Not Available

1993-11-01T23:59:59.000Z

238

Technical basis for radiological release of Grand Junction Office Building 2. Volume 2, dose assessment supporting data  

SciTech Connect (OSTI)

The second volume of the Grand Junction Office Action Program Technical Basis for Radiological Release of Grand Junction Office Building 2 report includes the data quality objectives (DQO), sampling plan, collected data, and analysis used to model future radiation doses to members of the public occupying Building 2 on the U.S. Department of Energy (DOE) Grand Junction Office (GJO) site. This volume was assembled by extracting relevant components of the Grand Junction Projects Office Remedial Action Project Building 2 Public Dose Evaluation (DOE 1996) and inserting recent additional data that was gathered and dose pathway modeling that was performed. The intent of this document is to provide all derived guidance decisions, assumptions, measured data, testing results, and pathway modeling software input and output data that supports the discussion and determinations presented in Volume 1 of this report. For constructive employment of this document, the reader is encouraged to closely follow Volume 1 for proper association with the segment of information being examined.

NONE

1997-07-01T23:59:59.000Z

239

The Oak Ridge Technical Information Center: A trailblazer in federal documentation  

SciTech Connect (OSTI)

This softbound book attempts to record the history of US AEC's Technical Information Center, from its conception (1947) to 1977. This organization centralizes and manages the issues related to control and dissemination of technical information, to fulfill the provisions of the Atomic Energy Act of 1946. TIC tried to search out and install efficient and economical systems for servicing the various technical information programs. It coordinated a direct organization-to-organization information exchange program, and it also participated in official bilateral exchange programs and in developing information systems for IAEA and Euratom. The work, planning, and strategies employed to achieve goals are chronicled in this book, whose 18 chapters are arranged into four sections according to different presidential administrations.

Vaden, W.M.

1992-01-01T23:59:59.000Z

240

Interim Control Strategy for the Test Area North/Technical Support Facility Sewage Treatment Facility Disposal Pond - Two-year Update  

SciTech Connect (OSTI)

The Idaho Cleanup Project has prepared this interim control strategy for the U.S. Department of Energy Idaho Operations Office pursuant to DOE Order 5400.5, Chapter 11.3e (1) to support continued discharges to the Test Area North/Technical Support Facility Sewage Treatment Facility Disposal Pond. In compliance with DOE Order 5400.5, a 2-year review of the Interim Control Strategy document has been completed. This submittal documents the required review of the April 2005 Interim Control Strategy. The Idaho Cleanup Project's recommendation is unchanged from the original recommendation. The Interim Control Strategy evaluates three alternatives: (1) re-route the discharge outlet to an uncontaminated area of the TSF-07; (2) construct a new discharge pond; or (3) no action based on justification for continued use. Evaluation of Alternatives 1 and 2 are based on the estimated cost and implementation timeframe weighed against either alternative's minimal increase in protection of workers, the public, and the environment. Evaluation of Alternative 3, continued use of the TSF-07 Disposal Pond under current effluent controls, is based on an analysis of four points: - Record of Decision controls will protect workers and the public - Risk of increased contamination is low - Discharge water will be eliminated in the foreseeable future - Risk of contamination spread is acceptable. The Idaho Cleanup Project recommends Alternative 3, no action other than continued implementation of existing controls and continued deactivation, decontamination, and dismantlement efforts at the Test Area North/Technical Support Facility.

L. V. Street

2007-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Review of Technical Studies in the United States in Support of Burnup Credit Regulatory Guidance  

SciTech Connect (OSTI)

Taking credit for the reduction in reactivity associated with fuel depletion can enable more cost-effective, higher-density storage, transport, disposal, and reprocessing of spent nuclear fuel (SNF) while maintaining sufficient subcritical margin to establish an adequate safety basis. Consequently, there continues to be considerable interest in the United States (U.S.), as well as internationally, in the increased use of burnup credit in SNF operations, particularly related to storage, transport, and disposal of commercial SNF. This interest has motivated numerous technical studies related to the application of burnup credit, both domestically and internationally, as well as the design of SNF storage, transport and disposal systems that rely on burnup credit for maintaining subcriticality. Responding to industry requests and needs, the U.S. Nuclear Regulatory Commission (NRC) initiated a burnup credit research program in 1999, with support from the Oak Ridge National Laboratory (ORNL), to develop regulatory guidance and the supporting technical bases for allowing and expanding the use of burnup credit in pressurized-water reactor SNF storage and transport applications. Although this NRC research program has not been continuous since its inception, considerable progress has been achieved in many key areas in terms of increased understanding of relevant phenomena and issues, availability of relevant information and data, and subsequently updated regulatory guidance for expanded use of burnup credit. This paper reviews technical studies performed by ORNL for the U.S. NRC burnup credit research program. Examples of topics include reactivity effects associated with reactor operating characteristics, fuel assembly characteristics, burnable absorbers, control rods, spatial burnup distributions, cooling time, and assembly misloading; methods and data for validation of isotopic composition predictions; methods and data for validation of criticality calculations; and operational issues and data related to assembly burnup confirmation. The objective of this paper is to summarize the work and significant accomplishments, with references to the technical reports and publications for complete details, and provide a useful resource to others in the burnup credit community.

Wagner, John C [ORNL] [ORNL; Parks, Cecil V [ORNL] [ORNL; Mueller, Don [ORNL] [ORNL; Gauld, Ian C [ORNL] [ORNL

2010-01-01T23:59:59.000Z

242

GridLAB-D Technical Support Document: Residential End-Use Module Version 1.0  

SciTech Connect (OSTI)

1.0 Introduction The residential module implements the following end uses and characteristics to simulate the power demand in a single family home: • Water heater • Lights • Dishwasher • Range • Microwave • Refrigerator • Internal gains (plug loads) • House (heating/cooling loads) The house model considers the following four major heat gains/losses that contribute to the building heating/cooling load: 1. Conduction through exterior walls, roof and fenestration (based on envelope UA) 2. Air infiltration (based on specified air change rate) 3. Solar radiation (based on CLTD model and using tmy data) 4. Internal gains from lighting, people, equipment and other end use objects. The Equivalent Thermal Parameter (ETP) approach is used to model the residential loads and energy consumption. The following sections describe the modeling assumptions for each of the above end uses and the details of power demand calculations in the residential module.

Taylor, Zachary T.; Gowri, Krishnan; Katipamula, Srinivas

2008-07-31T23:59:59.000Z

243

DOCKET NO: A-98-49 TECHNICAL SUPPORT DOCUMENT FOR SECTION 194.24  

E-Print Network [OSTI]

AND DATABASE CHANGES 3 2.1 Sources of New Data 3 2.2 Actinide Data Included in the Database 3 2.2.1 Americium

244

Technical Support Document for the National Environmental Policy Act Implementing Procedures  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy Usage »of Energy StrainClientDesignOffice - 20142012 | Department ofFebruary

245

Technical Support Document: Development of the Advanced Energy Design Guide for Grocery Stores--50% Energy Savings  

SciTech Connect (OSTI)

This report provides recommendations that architects, designers, contractors, developers, owners, and lessees of grocery store buildings can use to achieve whole-building energy savings of at least 50% over ASHRAE Standard 90.1-2004.

Hale, E. T.; Macumber, D. L.; Long, N. L.; Griffith, B. T.; Benne, K. S.; Pless, S. D.; Torcellini, P. A.

2008-09-01T23:59:59.000Z

246

Technical Support Document for the Department of Energy's Notice of Final  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of Inspector GeneralDepartment of Energyof theRestoration atStandards NewsletterRulemaking | Department of

247

Technical and analytical support to the ARPA Artificial Neural Network Technology Program  

SciTech Connect (OSTI)

Strategic Analysis (SA) has provided ongoing work for the Advanced Research Projects Agency (ARPA) Artificial Neural Network (ANN) technology program. This effort provides technical and analytical support to the ARPA ANN technology program in support of the following information areas of interest: (1) Alternative approaches for application of ANN technology, hardware approaches that utilize the inherent massive parallelism of ANN technology, and novel ANN theory and modeling analyses. (2) Promising military applications for ANN technology. (3) Measures to use in judging success of ANN technology research and development. (4) Alternative strategies for ARPA involvement in ANN technology R&D. These objectives were accomplished through the development of novel information management tools, strong SA knowledge base, and effective communication with contractors, agents, and other program participants. These goals have been realized. Through enhanced tracking and coordination of research, the ANN program is healthy and recharged for future technological breakthroughs.

NONE

1995-09-16T23:59:59.000Z

248

Supporting document for the north east quadrant historical tank content estimate report for C-Tank Farm  

SciTech Connect (OSTI)

This Supporting Document provides historical in-depth characterization information gathered on C-Tank Farm, such as historical waste transfer and level data, tank physical information, temperature data, sampling data, and drywell and liquid observation well data for Historical Tank Content Estimate Report of the NE Quadrant and the Hanford 200 East Areas.

Brevick, C.H.; Gaddis, L.A.; Walsh, A.C.

1994-06-01T23:59:59.000Z

249

Supporting document for the North East Quandrant Historical Tank Content Estimate Report for BX-Tank Farm  

SciTech Connect (OSTI)

This supporting document provides historical in-depth characterization information gathered on BX-Tank Farm, such as historical waste transfer and level data, tank physical information, temperature data, sampling data, and drywell and liquid observation well data for Historical Tank Content Estimate Report of the NE Quandrant and the Hanford 200 East Areas.

Brevick, C.H.

1994-06-01T23:59:59.000Z

250

Technical requirements specification for tank waste retrieval  

SciTech Connect (OSTI)

This document provides the technical requirements specification for the retrieval of waste from the underground storage tanks at the Hanford Site. All activities covered by this scope are conducted in support of the Tank Waste Remediation System (TWRS) mission.

Lamberd, D.L.

1996-09-26T23:59:59.000Z

251

Technical data summary supporting the spent nuclear fuel environment impact statement, March 1994  

SciTech Connect (OSTI)

This report has been compiled by the WSRC Nuclear Materials Processing Division`s Planning Section at the request of the Office of Spent Fuel Management and Special Projects (EM-37) to support issuance of the Spent Nuclear Fuel Environmental Impact Statement. Savannah River Site input data evaluates five programmatic options (including {open_quotes}No Action{close_quotes}) ranging up to transfer of all DOE responsibility spent fuel to the SRS. For each option, a range of management/disposition scenarios has been examined. Each case summary provides information relative to the technical proposal, technical issues, environmental impacts, and projected costs for a forty year period (FY-35) when it is assumed that the material will be dispositioned from the SRS. The original issue of the report which was prepared under severe time constraints contained many simplifications and assumptions. Although the revisions have corrected some of the shortcomings of the original report, it is still highly recommended that significant additional study be performed before basing key decisions upon the data contained in this report. The data represents the best effort by a significant group of technical personnel familiar with nuclear materials processing, handling, and storage; but it is likely that careful scrutiny will reveal numerous discrepancies, inconsistencies and omissions. Nor does this report attempt to analyze every potential disposal pathway, but probably establishes the bounds for the most of the viable pathways. The bulk of the effort went into defining the engineering approaches necessary to execute the various mission scenarios which were changed since the last revision. The decision to limit reprocessing to only SRS aluminum clad required a major alteration of the TDS. Collection and/or calculation of much of the various waste, emission, and utility consumption data, so important to an EIS, has been updated since the last revision, but not thoroughly completed.

Geddes, R.L.; Claxton, R.E.; Lengel, J.D. [and others

1994-03-01T23:59:59.000Z

252

Due June 15, 2010 Supporting documentation is requested for all affirmative responses  

E-Print Network [OSTI]

documentation is requested for all affirmative responses Goal I: Develop a shared and inclusive understanding and management 6. The «School_form» has a goal to increase diversity among senior leadership. Yes___ No___ 7

Larson-Prior, Linda

253

Carbon Calculator for Land Use Change from Biofuels Production (CCLUB). Users' manual and technical documentation.  

SciTech Connect (OSTI)

The Carbon Calculator for Land Use Change from Biofuels Production (CCLUB) calculates carbon emissions from land use change (LUC) for four different ethanol production pathways including corn grain ethanol and cellulosic ethanol from corn stover, miscanthus, and switchgrass. This document discusses the version of CCLUB released May 31, 2012 which includes corn, as did the previous CCLUB version, and three cellulosic feedstocks: corn stover, miscanthus, and switchgrass. CCLUB calculations are based upon two data sets: land change areas and above- and below-ground carbon content. Table 1 identifies where these data are stored and used within the CCLUB model, which is built in MS Excel. Land change area data is from Purdue University's Global Trade Analysis Project (GTAP) model, a computable general equilibrium (CGE) economic model. Section 2 describes the GTAP data CCLUB uses and how these data were modified to reflect shrubland transitions. Feedstock- and spatially-explicit below-ground carbon content data for the United States were generated with a surrogate model for CENTURY's soil organic carbon sub-model (Kwon and Hudson 2010) as described in Section 3. CENTURY is a soil organic matter model developed by Parton et al. (1987). The previous CCLUB version used more coarse domestic carbon emission factors. Above-ground non-soil carbon content data for forest ecosystems was sourced from the USDA/NCIAS Carbon Online Estimator (COLE) as explained in Section 4. We discuss emission factors used for calculation of international greenhouse gas (GHG) emissions in Section 5. Temporal issues associated with modeling LUC emissions are the topic of Section 6. Finally, in Section 7 we provide a step-by-step guide to using CCLUB and obtaining results.

Mueller, S; Dunn, JB; Wang, M (Energy Systems); (Univ. of Illinois at Chicago)

2012-06-07T23:59:59.000Z

254

Hanford spent nuclear fuel project recommended path forward, volume III: Alternatives and path forward evaluation supporting documentation  

SciTech Connect (OSTI)

Volume I of the Hanford Spent Nuclear Fuel Project - Recommended Path Forward constitutes an aggressive series of projects to construct and operate systems and facilities to safely retrieve, package, transport, process, and store K Basins fuel and sludge. Volume II provided a comparative evaluation of four Alternatives for the Path Forward and an evaluation for the Recommended Path Forward. Although Volume II contained extensive appendices, six supporting documents have been compiled in Volume III to provide additional background for Volume II.

Fulton, J.C.

1994-10-01T23:59:59.000Z

255

Client Support: Responsible for the IT service desk, help center, technical support, divisional support and many other user support issues for CCNY community.  

E-Print Network [OSTI]

@ccny.cuny.edu Howard Schneiderman, Sophie Davis- Network Administrator 6958 646-261-4675 howie@ccny.cuny.edu IT Service, Service Desk Manager 5828 646-631-0356 ivette@ccny.cuny.edu Patrick Flores, Administration-Tech Support Specialist 5064 917-692-9486 pflores@ccny.cuny.edu Robert Hernandez, CWE- Computer Systems Administrator 212

Brinkmann, Peter

256

OSH technical reference manual  

SciTech Connect (OSTI)

In an evaluation of the Department of Energy (DOE) Occupational Safety and Health programs for government-owned contractor-operated (GOCO) activities, the Department of Labor`s Occupational Safety and Health Administration (OSHA) recommended a technical information exchange program. The intent was to share written safety and health programs, plans, training manuals, and materials within the entire DOE community. The OSH Technical Reference (OTR) helps support the secretary`s response to the OSHA finding by providing a one-stop resource and referral for technical information that relates to safe operations and practice. It also serves as a technical information exchange tool to reference DOE-wide materials pertinent to specific safety topics and, with some modification, as a training aid. The OTR bridges the gap between general safety documents and very specific requirements documents. It is tailored to the DOE community and incorporates DOE field experience.

Not Available

1993-11-01T23:59:59.000Z

257

QUEST2: Release 1, SA/Release 1 supporting documents deliverable set  

SciTech Connect (OSTI)

This document contains deliverables which reflect the last of the System Architecture phase analysis for the Quality, Environmental, Safety Tracking System redesign (QUEST2) project. These deliverables are focused on the final insights required to start functional design of the first QUEST2 release. They include the data definitions, conversion rules, standards for design and user interface, performance criteria, and rules to be followed during the prototyping activity described in the Project Management Plan.

Braaten, F.D.

1995-02-27T23:59:59.000Z

258

Supporting document for the historical tank content estimate for SY-tank farm  

SciTech Connect (OSTI)

The purpose of this historical characterization document is to present the synthesized summaries of the historical records concerning the physical characteristics, radiological, and chemical composition of mixed wastes stored in underground double-shell tanks and the physical condition of these tanks. The double-shell tanks are located on the United States Department of Energy`s Hanford Site, approximately 25 miles northwest or Richland, Washington. The document will be used to assist in characterizing the waste in the tanks in conjunction with the current program of sampling and analyzing the tank wastes. Los Alamos National Laboratory (LANL) developed computer models that used the historical data to attempt to characterize the wastes and to generate estimates of each tank`s inventory. A historical review of the tanks may reveal anomalies or unusual contents that could be critical to characterization and post characterization activities. This document was developed by reviewing the operating plant process histories, waste transfer data, and available physical and chemical data from numerous resources. These resources were generated by numerous contractors from 1945 to the present. Waste characterization, the process of describing the character or quality of a waste, is required by Federal law (Resource Conservation and Recovery Act [RCRA]) and state law (Washington Administrative Code [WAC] 173-303, Dangerous Waste Regulations). Characterizing the waste is necessary to determine methods to safely retrieve, transport, and/or treat the wastes.

Brevick, C.H.

1997-08-12T23:59:59.000Z

259

Impact assessment of draft DOE Order 5820.2B. Radioactive Waste Technical Support Program  

SciTech Connect (OSTI)

The Department of Energy (DOE) has prepared a revision to DOE Order 5820.2A, entitled ``Radioactive Waste Management.`` DOE issued DOE Order 5820.2A in September 1988 and, as the title implies, it covered only radioactive waste forms. The proposed draft order, entitled ``Waste Management,`` addresses the management of both radioactive and nonradioactive waste forms. It also includes spent nuclear fuel, which DOE does not consider a waste. Waste forms covered include hazardous waste, high-level waste, transuranic (TRU) waste, low-level radioactive waste, uranium and thorium mill tailings, mixed waste, and sanitary waste. The Radioactive Waste Technical Support Program (TSP) of Leached Idaho Technologies Company (LITCO) is facilitating the revision of this order. The EM Regulatory Compliance Division (EM-331) has requested that TSP estimate the impacts and costs of compliance with the revised order. TSP requested Dames & Moore to aid in this assessment by comparing requirements in Draft Order 5820.2B to ones in DOE Order 5820.2A and other DOE orders and Federal regulations. The assessment started with a draft version of 5820.2B dated January 14, 1994. DOE has released three updated versions of the draft order since then (dated May 20, 1994; August 26, 1994; and January 23, 1995). Each time DOE revised the order, Dames and Moore updated the assessment work to reflect the text changes. This report reflects the January 23, 1995 version of the draft order.

NONE

1995-04-01T23:59:59.000Z

260

SPEAR3 | Technical Documentation  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 -the Mid-Infrared0 ResourceAwards SAGE Awards ,#2446Smalln n u a l rBeamLodging

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

GPHS-RTGs in support of the Cassini Mission. Semi annual technical report, 30 September 1996--30 March 1997  

SciTech Connect (OSTI)

The technical progress achieved during the period 27 January through 30 September 1996 through 30 March 1997 on Contract DE-AC03-91SF18852 Radioisotope Thermoelectric Generators and Ancillary Activities is described. This report is organized by program task structure: spacecraft integration and liaison; engineering support; safety; qualified unicouple production; ETG fabrication, assembly, and test; ground support equipment (GSE); RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance, reliability, contract changes, CAGO acquisition (operating funds), and CAGO maintenance and repair; and CAGO acquisition (capital funds).

NONE

1997-04-20T23:59:59.000Z

262

Building America Best Practices Series Volume 8: Builders Challenge Quality Criteria Support Document  

SciTech Connect (OSTI)

The U.S. Department of Energy (DOE) has posed a challenge to the homebuilding industry—to build 220,000 high-performance homes by 2012. Through the Builders Challenge, participating homebuilders will have an easy way to differentiate their best energy-performing homes from other products in the marketplace, and to make the benefits clear to buyers. This document was prepared by Pacific Northwest National Laboratory for DOE to provide guidance to U.S. home builders who want to accept the challenge. To qualify for the Builders Challenge, a home must score 70 or less on the EnergySmart Home Scale (E-Scale). The E-scale is based on the well-established Home Energy Rating System (HERS) index, developed by the Residential Energy Services Network (RESNET). The E-scale allows homebuyers to understand – at a glance – how the energy performance of a particular home compares with the performance of others. To learn more about the index and HERS Raters, visit www.natresnet.org. Homes also must meet the Builders Challenge criteria described in this document. To help builders meet the Challenge, guidance is provided in this report for each of the 29 criteria. Included with guidance for each criteria are resources for more information and references for relevant codes and standards. The Builders Challenge Quality Criteria were originally published in Dec. 2008. They were revised and published as PNNL-18009 Rev 1.2 in Nov. 2009. This is version 1.3, published Nov 2010. Changes from the Nov 2009 version include adding a title page and updating the Energy Star windows critiera to the Version 5.0 criteria approved April 2009 and effective January 4, 2010. This document and other information about the Builders Challenge is available on line at www.buildingamerica.gov/challenge.

Baechler, Michael C.; Bartlett, Rosemarie; Gilbride, Theresa L.

2010-11-01T23:59:59.000Z

263

Technical Information to Support Double Shell Tank (DST) Emergency Annulus Pumping [SEC 1 and 2  

SciTech Connect (OSTI)

This document provides the design calculations for the DST Annulus Emergency Pumping Project. This document also contains essential information relative to DST annulus emergency pumping that may not be found in other documents. This information consists of the following: Index drawing for annulus pumping; References to the Acceptance Test Report, DST Emergency Pumping Guide, Time Deployment study, etc.; Statements of work; and Reference CEIS and RMIS numbers. A Vendor Information document, VI-50121, is not included in this document, but a copy can be obtained by contacting Document Control Services. This document contains various information regarding the Hydrostar pumps, such as the air motor, cylinder size, pump installation and operation manual. It also contains information regarding the Flygt BS2060 submersible pump, such as parts list, pump handling, preventative maintenance, overhaul and repair. In addition, this document also has information on 3-way PM ball valves, electrical skid components and the alternate Gurman-Rupp stainless steel submersible pump.

REBERGER, D.W.

2000-09-14T23:59:59.000Z

264

Support Vector Machines Issues in the classification of text documents Learning Boolean Weights Learning Real-Valued Web Search and Text Mining  

E-Print Network [OSTI]

Support Vector Machines Issues in the classification of text documents Learning Boolean Weights Vector Machines and Learning to Rank Alexander Gray Georgia Institute of Technology, College of Computing 2011 Gray: Support Vector Machines and Learning to Rank 1 / 59 #12;Support Vector Machines Issues

Gray, Alexander

265

Documentation, User Support, and Verification of Wind Turbine and Plant Models  

SciTech Connect (OSTI)

As part of the Utility Wind Energy Integration Group (UWIG) and EnerNex's Wind Turbine Modeling Project, EnerNex has received ARRA (federal stimulus) funding through the Department of Energy (DOE) to further the progress of wind turbine and wind plant models. Despite the large existing and planned wind generation deployment, industry-standard models for wind generation have not been formally adopted. Models commonly provided for interconnection studies are not adequate for use in general transmission planning studies, where public, non-proprietary, documented and validated models are needed. NERC MOD (North American Electric Reliability Corporation) reliability standards require that power flow and dynamics models be provided, in accordance with regional requirements and procedures. The goal of this project is to accelerate the appropriate use of generic wind turbine models for transmission network analysis by: (1) Defining proposed enhancements to the generic wind turbine model structures that would allow representation of more advanced; (2) Comparative testing of the generic models against more detailed (and sometimes proprietary) versions developed by turbine vendors; (3) Developing recommended parameters for the generic models to best mimic the performance of specific commercial wind turbines; (4) Documenting results of the comparative simulations in an application guide for users; (5) Conducting technology transfer activities in regional workshops for dissemination of knowledge and information gained, and to engage electric power and wind industry personnel in the project while underway; (6) Designing of a "living" homepage to establish an online resource for transmission planners.

Robert Zavadil; Vadim Zheglov; Yuriy Kazachkov; Bo Gong; Juan Sanchez; Jun Li

2012-09-18T23:59:59.000Z

266

Supporting document for the historical tank content estimate for A Tank Farm  

SciTech Connect (OSTI)

This document provides historical evaluations of the radioactive mixed wastes stored in the Hanford Site 200-East Area underground single-shell tanks (SSTs). A Historical Tank Content Estimate has been developed by reviewing the process histories, waste transfer data, and available physical and chemical characterization data from various Department of Energy (DOE) and Department of Defense (DOD) contractors. The historical data will supplement information gathered from in-tank core sampling activities that are currently underway. A tank history review that is accompanied by current characterization data creates a complete and reliable inventory estimate. Additionally, historical review of the tanks may reveal anomalies or unusual contents that are critical to characterization and post characterization activities. Complete and accurate tank waste characterizations are critical first steps for DOE and Westinghouse Hanford Company safety programs, waste pretreatment, and waste retrieval activities. The scope of this document is limited to the SSTs in the A Tank Farm of the northeast quadrant of the 200 East Area. Nine appendices compile data on: tank level histories; temperature graphs; surface level graphs; drywell graphs; riser configuration and tank cross section; sampling data; tank photographs; unknown tank transfers; and tank layering comparison. 113 refs.

Brevick, C.H.; Gaddis, L.A.; Walsh, A.C.

1994-06-01T23:59:59.000Z

267

Supporting document for the historical tank content estimate for B Tank Farm  

SciTech Connect (OSTI)

This document provides historical evaluations of the radioactive mixed wastes stored in the Hanford Site 200-East Area underground single-shell tanks (SSTs). A Historical Tank Content Estimate has been developed by reviewing the process histories, waste transfer data, and available physical and chemical characterization data from various Department of Energy (DOE) and Department of Defense (DOD) contractors. The historical data will supplement information gathered from in-tank core sampling activities that are currently underway. A tank history review that is accompanied by current characterization data creates a complete and reliable inventory estimate. Additionally, historical review of the tanks may reveal anomalies or unusual contents that are critical to characterization and post characterization activities. Complete and accurate tank waste characterizations are critical first steps for DOE and Westinghouse Hanford Company safety programs, waste pretreatment, and waste retrieval activities. The scope of this document is limited to the SSTs in the B Tank Farm of the northeast quadrant of the 200 East Area. Nine appendices compile data on: tank level histories; temperature graphs; surface level graphs; drywell graphs; riser configuration and tank cross section; sampling data; tank photographs; unknown tank transfers; and tank layering comparison. 113 refs.

Brevick, C.H.; Gaddis, L.A.; Johnson, E.D.

1994-06-01T23:59:59.000Z

268

Supporting document for the historical tank content estimate for BY Tank Farm  

SciTech Connect (OSTI)

This document provides historical evaluations of the radioactive mixed wastes stored in the Hanford Site 200-East Area underground single-shell tanks (SSTs). A Historical Tank Content Estimate has been developed by reviewing the process histories, waste transfer data, and available physical and chemical characterization data from various Department of Energy (DOE) and Department of Defense (DOD) contractors. The historical data will supplement information gathered from in-tank core sampling activities that are currently underway. A tank history review that is accompanied by current characterization data creates a complete and reliable inventory estimate. Additionally, historical review of the tanks may reveal anomalies or unusual contents that are critical to characterization and post characterization activities. Complete and accurate tank waste characterizations are critical first steps for DOE and Westinghouse Hanford Company safety programs, waste pretreatment, and waste retrieval activities. The scope of this document is limited to the SSTs in the BY Tank Farm of the northeast quadrant of the 200 East Area. Nine appendices contain data on: tank level histories; temperature graphs; surface level graphs; drywell graphs; riser configuration and tank cross section; sampling data; tank photographs; unknown tank transfers; and tank layering comparison. 113 refs.

Brevick, C.H.; Gaddis, L.A.; Walsh, A.C.

1994-06-01T23:59:59.000Z

269

Supporting document for the historical tank content estimate for S tank farm  

SciTech Connect (OSTI)

This document provides historical evaluations of the radioactive mixed wastes stored in the Hanford Site 200 West Area underground single-shell tanks (SSTs). A Historical Tank Content Estimate has been developed by reviewing the process histories, waste transfer data, and available physical and chemical characterization data from various Department of Energy (DOE) and Department of Defense (DOD) contractors. The historical data will supplement information gathered from in-tank core sampling activities that are currently underway. A tank history review that is accompanied by current characterization data creates a complete and reliable inventory estimate. Additionally, historical review of the tanks may reveal anomalies or unusual contents that are critical to characterization and post characterization activities. Complete and accurate tank waste characterizations are critical first steps for DOE and Westinghouse Hanford Company safety programs, waste pretreatment, and waste retrieval activities. The scope of this document is limited to all the SSTs in the S Tank Farm of the southwest quadrant of the 200 West Area. Nine appendices compile data on: tank level histories; temperature graphs; surface level graphs; drywell graphs; riser configuration and tank cross section; sampling data; tank photographs; unknown tank transfers; and tank layering comparison. 113 refs.

Brevick, C.H.; Gaddis, L.A.; Walsh, A.C.

1994-06-01T23:59:59.000Z

270

Support Services Division Refer to end of document for revisions August 2007.1  

E-Print Network [OSTI]

& Safety at Work etc., Act 1974, the Management of Health & Safety at Work Regulations 1999 of the works. Contractors must take all reasonable precautions to ensure the health and safety of all those (Estates) Building Projects Safety Code of Practice (Construction) 2007 South Kensington Campus #12;Support

271

TECHNICAL COMPARISON OF CANDIDATE ION EXCHANGE MEDIA FOR SMALL COLUMN ION EXCHANGE (SCIX) APPLICATIONS IN SUPPORT OF SUPPLEMENTAL LAW PRETREATMENT  

SciTech Connect (OSTI)

At-tank supplemental pretreatment including both filtration and small column ion exchange is currently under evaluation to facilitate salt waste retrieval and processing in the Hanford tank farms. Spherical resorcinol formaldehyde (sRF) resin is the baseline ion exchange resin for use in the Waste Treatment and Immobilization Plant (WTP). This document provides background and technical rationale to assist in determining whether spherical resorcinol formaldehyde (sRF) is also the appropriate ion exchange resin for supplemental LAW pretreatment processes and compares sRF with crystalline silicotitanate (CST) as potential supplemental pretreatment ion exchange media.

RAMSEY AA; THORSON MR

2010-12-28T23:59:59.000Z

272

Texas geothermal R D and D program planning support document. Final report  

SciTech Connect (OSTI)

Program planning support was provided by; developing a geothermal RD and D program structure, characterizing the status of geothermal RD and D through review of literature and interaction with the geothermal research community, developing a candidate list of future Texas geothermal projects, and prioritizing the candidate projects based on appropriate evaluation criteria. The method used to perform this study and the results thereof are presented. Summary reviews of selected completed and ongoing projects and summary descriptions and evaluations of the candidate RD and D projects ar provided. A brief discussion emerging federal RD and D policies is presented. References and independent project rankings by three of the GRP members are included. (MHR)

Davis, R.J.; Conover, M.F.; Keeney, R.C.; Personett, M.L.; Richmann, D.L.

1981-08-28T23:59:59.000Z

273

Canister storage building (CSB) safety analysis report phase 3: Safety analysis documentation supporting CSB construction  

SciTech Connect (OSTI)

The Canister Storage Building (CSB) will be constructed in the 200 East Area of the U.S. Department of Energy (DOE) Hanford Site. The CSB will be used to stage and store spent nuclear fuel (SNF) removed from the Hanford Site K Basins. The objective of this chapter is to describe the characteristics of the site on which the CSB will be located. This description will support the hazard analysis and accident analyses in Chapter 3.0. The purpose of this report is to provide an evaluation of the CSB design criteria, the design's compliance with the applicable criteria, and the basis for authorization to proceed with construction of the CSB.

Garvin, L.J.

1997-04-28T23:59:59.000Z

274

ARRA FEMP Technical Assistance -- Federal Aviation Administration Project 209 -- Control Tower and Support Building, Palm Springs, CA  

SciTech Connect (OSTI)

This report represents findings of a design review team that evaluated construction documents (at the 100% level) and operating specifications for a new control tower and support building that will be built in Palm Springs, California by the Federal Aviation Administration (FAA). The focus of the review was to identify measures that could be incorporated into the final design and operating specifications that would result in additional energy savings for the FAA that would not have otherwise occurred.

Arends, J.; Sandusky, William F.

2010-03-31T23:59:59.000Z

275

UNCLASSIFIHED DEFENSE DOCUMENTATION CENTER  

E-Print Network [OSTI]

UNCLASSIFIHED AD 463473 DEFENSE DOCUMENTATION CENTER FOR SCIENTIFIC AND TECHNICAL INFORMATION .... John Barton Head OR Analysis Group R. H. Krolick Manager Applied Science Laboratory Prepared for the .J

Block, Marco

276

Technical Services Contract Awarded for West Valley Demonstration Project Support Services  

Broader source: Energy.gov [DOE]

Cincinnati - The U.S. Department of Energy (DOE) today awarded a task order to Safety and Ecology Corporation of Knoxville, Tennessee, for technical services at the West Valley Demonstration Project, West Valley, New York. The task order has a three-year performance period with a $1.3 million value.

277

Providing Internet access to Los Alamos National Laboratory technical reports: A case history in providing public access to previously restricted documents  

SciTech Connect (OSTI)

The Los Alamos National Laboratory (LANL) Research Library recently fulfilled a strategic goal of providing worldwide desktop access via the Internet to full-image files of the complete unclassified holdings of Los Alamos technical reports in its Report Collection. This effort began in late 1994 with the scanning of paper and microfiche format reports. Concurrently, the Research Library helped to initiate shifting the model for publishing new technical reports from paper to electronic; the files could then be directly mounted on the Research Library`s Web server. Providing desktop access to these reports was instrumental in expediting the development of internal policies that would better define what documents, previously restricted to the general public, could be publicly released. Undoubtedly, the most significant category of such reports were previously classified reports that had been declassified, but had not gone through a further review for public release. Collaboration with LANL`s Classification Group led to approval for public release of 97% of these reports. The LANL Research Library`s Web site now offers unique and unprecedented access to the world of a huge body of technical reports never available before anywhere in any form. This paper discusses the issues and steps involved in this achievement.

Collins, K.A.

1996-12-31T23:59:59.000Z

278

Technical Consultant RFP | Department of Energy  

Energy Savers [EERE]

RFP Technical Consultant RFP Technical Consultant RFP, from the Tool Kit Framework: Small Town University Energy Program (STEP). C3b Technical Consultant RFP.pdf More Documents &...

279

Technical Standards, Program Project Justification Statement...  

Office of Environmental Management (EM)

More Documents & Publications DOE-TSPP-2-2013, Initiating DOE Technical Standards DOE-TSPP-7-2013, Maintaining DOE Technical Standards Technical Standards Newsletter - March 2014...

280

Engineering support services for the DOE/GRI coal gasification research program. Final technical progress report, October 1978-November 1982  

SciTech Connect (OSTI)

The agreement between the United States Government Department of Energy and the Gas Research Institute for the Joint Coal Gasification Research Program provided for one or more technical evaluation contractors. Pullman Kellogg (now the M.W. Kellogg Company) was selected as evaluation contractor to assess, and report to the DOE/GRI Operating Committee on, the relative merits of the active programs covered by the agreement. This report includes the period from 1 October 1978 to 30 November 1982. The objective was to provide engineering support for the DOE/GRI high Btu coal gasification program. This support generally consisted of assistance in developing or advancing each process to its maximum potential. Kellogg monitored and evaluated the startup and operational activities of all pilot plant projects within the combined DOE/GRI program. Kellogg evaluated proposals to determine their technical feasibility as potential processes or as viable processing operations for commercial-scale gasification of coal. Kellogg also recorded observations on the reliability, maintainability, and availability of the equipment used in the pilot plant or PDU facilities. Kellogg performed design reviews, data analyses, and engineering evaluations of proposals, cost estimates and monthly progress reports to provide information considered essential to the overall objectives of the combined DOE/GRI program.

Bostwick, L.E.

1982-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Sustainability Support  

Broader source: Energy.gov [DOE]

Sustainability Support serves as a corporate technical assistance, coordination, and integration resource to support line organizations in the resolution of sustainability issues and management concerns.

282

Monitored Geologic Repository Project Description Document  

SciTech Connect (OSTI)

The primary objective of the Monitored Geologic Repository Project Description Document (PDD) is to allocate the functions, requirements, and assumptions to the systems at Level 5 of the Civilian Radioactive Waste Management System (CRWMS) architecture identified in Section 4. It provides traceability of the requirements to those contained in Section 3 of the Yucca Mountain Site Characterization Project Requirements Document (YMP RD) (YMP 2001a) and other higher-level requirements documents. In addition, the PDD allocates design related assumptions to work products of non-design organizations. The document provides Monitored Geologic Repository (MGR) technical requirements in support of design and performance assessment in preparing for the Site Recommendation (SR) and License Application (LA) milestones. The technical requirements documented in the PDD are to be captured in the System Description Documents (SDDs) which address each of the systems at Level 5 of the CRWMS architecture. The design engineers obtain the technical requirements from the SDDs and by reference from the SDDs to the PDD. The design organizations and other organizations will obtain design related assumptions directly from the PDD. These organizations may establish additional assumptions for their individual activities, but such assumptions are not to conflict with the assumptions in the PDD. The PDD will serve as the primary link between the technical requirements captured in the SDDs and the design requirements captured in US Department of Energy (DOE) documents. The approved PDD is placed under Level 3 baseline control by the CRWMS Management and Operating Contractor (M&O) and the following portions of the PDD constitute the Technical Design Baseline for the MGR: the design characteristics listed in Table 1-1, the MGR Architecture (Section 4.1), the Technical Requirements (Section 5), and the Controlled Project Assumptions (Section 6).

P. Curry

2001-06-26T23:59:59.000Z

283

Monitored Geologic Repository Project Description Document  

SciTech Connect (OSTI)

The primary objective of the Monitored Geologic Repository Project Description Document (PDD) is to allocate the functions, requirements, and assumptions to the systems at Level 5 of the Civilian Radioactive Waste Management System (CRWMS) architecture identified in Section 4. It provides traceability of the requirements to those contained in Section 3 of the ''Monitored Geologic Repository Requirements Document'' (MGR RD) (YMP 2000a) and other higher-level requirements documents. In addition, the PDD allocates design related assumptions to work products of non-design organizations. The document provides Monitored Geologic Repository (MGR) technical requirements in support of design and performance assessment in preparing for the Site Recommendation (SR) and License Application (LA) milestones. The technical requirements documented in the PDD are to be captured in the System Description Documents (SDDs) which address each of the systems at Level 5 of the CRWMS architecture. The design engineers obtain the technical requirements from the SDDs and by reference from the SDDs to the PDD. The design organizations and other organizations will obtain design related assumptions directly from the PDD. These organizations may establish additional assumptions for their individual activities, but such assumptions are not to conflict with the assumptions in the PDD. The PDD will serve as the primary link between the technical requirements captured in the SDDs and the design requirements captured in US Department of Energy (DOE) documents. The approved PDD is placed under Level 3 baseline control by the CRWMS Management and Operating Contractor (M and O) and the following portions of the PDD constitute the Technical Design Baseline for the MGR: the design characteristics listed in Table 1-1, the MGR Architecture (Section 4.1), the Technical Requirements (Section 5), and the Controlled Project Assumptions (Section 6).

P. M. Curry

2001-01-30T23:59:59.000Z

284

Provision of utility support services to the US Department of Energy San Francisco Operations Office. Final technical report  

SciTech Connect (OSTI)

The main purpose of this project was to provide to DOE/SAN continuing, follow-up support to realize savings from a number of alternate supply arrangements that had already been and/or were expected to be identified under the original project. This expected continuation of these efforts is demonstrated by certain of the tasks that are spelled out in the Statement of Work. For example: Evaluate and propose alternative options and methods for improving efficiency, reducing cost, and making effective use of the energy supplies and facilities under various conditions of use; Provide engineering and economic analysis and recommendations for utility-related facilities and service issues, such as high voltage discounts, ownership of facilities, etc.; Assist in developing strategy and documentation in support of negotiating utility contracts and modifications thereto. In addition, the follow-on contract provided for monitoring and intervening in rate cases that had particular relevance to the DOE/SAN laboratories.

Not Available

1994-04-01T23:59:59.000Z

285

DOE Awards Small Business Task Order for Technical Support to the Office of  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarly Career Scientists'Montana. DOCUMENTS AVAILABLEReportEnergyDeveloping aCleanDepartment ofEnvironmental

286

Management support services to the Office of Utility Technologies. Final technical report  

SciTech Connect (OSTI)

The Office of Utility Technologies works cooperatively with industry and the utility sector to realize the market potential for energy efficiency and renewable energy technologies. Under this contract, BNF has provided management support services for OUT R&D activities for the following Program offices: (1) Office of Energy Management; (2) Office of Solar Energy Conversion; (3) Office of Renewable Energy Conversion; and (4) Deputy Assistant Secretary. During the period between 4/17/91 and 9/17/93, BNF furnished the necessary personnel, equipment, materials, facilities and travel required to provide management support services for each of the above Program Offices. From 9/18/93 to 12/17/93, BNF has been involved in closeout activities, including final product deliverables. Research efforts that have been supported in these Program Offices are: (1) for Energy Management -- Advanced Utility Concepts Division; Utility Systems Division; Integrated Planning; (2) for Solar Energy Conversion -- Photovoltaics Division; Solar Thermal and Biomass Power Division; (3) for Renewable Energy Conversion -- Geothermal Division; Wind, Hydroelectric and Ocean Systems Division; (4) for the Deputy Assistant Secretary -- support as required by the Supporting Staff. This final report contains summaries of the work accomplished for each of the Program Offices listed above.

Not Available

1993-12-16T23:59:59.000Z

287

Technical Support Document: Development of the Advanced Energy Design Guide for Medium Box Retail -- 50% Energy Savings  

SciTech Connect (OSTI)

This report provides recommendations that architects, designers, contractors, developers, owners, and lessees of medium box retail buildings can use to achieve whole-building energy savings of at least 50% over ASHRAE Standard 90.1-2004. The recommendations are given by climate zone and address building envelope, fenestration, lighting systems, HVAC systems, building automation and controls, outside air treatment, service water heating, plug loads, and photovoltaic systems. The report presents several paths to 50% savings, which correspond to different levels of integrated design. These are recommendations only, and are not part of a code or standard. The recommendations are not exhaustive, but we do try to emphasize the benefits of integrated building design, that is, a design approach that analyzes a building as a whole system, rather than as a disconnected collection of individually engineered subsystems.

Hale, E. T.; Macumber, D. L.; Long, N. L.; Griffith, B. T.; Benne, K. S.; Pless, S. D.; Torcellini, P. A.

2008-09-01T23:59:59.000Z

288

DOE TRANSCOM Technical Support Services DE-EM0002903 PART III - LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed Newcatalyst phases onOrganization FYBeau Newmango!DepartmentServiceDOE TRANSCOMPART

289

Radiation site cleanup regulations: Technical support document for the development of radionuclide cleanup levels for soil. Review draft  

SciTech Connect (OSTI)

This report presents EPA`s approach to assessing some of the beneficial and adverse radiation health effects associated with various possible values for an annual dose limit. In particular, it discusses the method developed to determine how the choice of cleanup criterion affects (1) the time-integrated numbers of non-fatal and fatal radiogenic cancers averted among future populations, (2) the occurrence of radiogenic cancers among remediation workers and the public caused by the cleanup process itself, and (3) the volume of contaminated soil that may require remediation.

Wolbarst, A.B.; Mauro, J.; Anigstein, R.; Back, D.; Bartlett, J.W.

1994-09-24T23:59:59.000Z

290

Final Technical Report: Supporting Wind Turbine Research and Testing - Gearbox Durability Study  

SciTech Connect (OSTI)

The combination of premature failure of wind turbine gearboxes and the downtime caused by those failures leads to an increase in the cost of electricity produced by the wind. There is a need for guidance to asset managers regarding how to maximize the longevity of their gearboxes in order to help keep the cost of wind energy as low as possible. A low cost of energy supports the US Department of Energy's goal of achieving 20% of the electricity in the United States produced by wind by the year 2030. DNV KEMA has leveraged our unique position in the industry as an independent third party engineering organization to study the problem of gearbox health management and develop guidance to project operators. This report describes the study. The study was conducted in four tasks. In Task 1, data that may be related to gearbox health and are normally available to wind project operators were collected for analysis. Task 2 took a more in-depth look at a small number of gearboxes to gain insight in to relevant failure modes. Task 3 brought together the previous tasks by evaluating the available data in an effort to identify data that could provide early indications of impending gearbox failure. Last, the observations from the work were collected to develop recommendations regarding gearbox health management.

Matthew Malkin

2012-04-30T23:59:59.000Z

291

Technical support to the Solvent Refined Coal (SRC) demonstration projects: assessment of current research and development  

SciTech Connect (OSTI)

A program to demonstrate Solvent Refined Coal (SRC) technology has been initiated by the US Department of Energy (DOE) in partnership with two industrial groups. Project management responsibility has been assigned to the Oak Ridge Operations Office (ORO) of DOE. ORO requested that the Oak Ridge National Laboratory assess current research and development (R and D) activities and develop recommendations for those activities that might contribute to successful completion of the SRC demonstration plant projects. The objectives of this final report are to discuss in detail the problem areas in SRC; to discuss the current and planned R and D investigations relevant to the problems identified; and to suggest appropriate R and D activities in support of designs for the SRC demonstration plants. Four types of R and D activities are suggested: continuation of present and planned activities; coordination of activities and results, present and proposed; extension/redirection of activities not involving major equipment purchase or modifications; and new activities. Important examples of the first type of activity include continuation of fired heater, slurry rheology, and slurry mixing studies at Ft. Lewis. Among the second type of activity, coordination of data acquisition and interpretation is recommended in the areas of heat transfer, vapor/liquid equilibria, and physical properties. Principal examples of recommendations for extension/redirection include screening studies at laboratory scale on the use of carbonaceous precoat (e.g., anthracite) infiltration, and 15- to 30-day continuous tests of the Texaco gasifier at the Texaco Montebello facility (using SRC residues).

Edwards, M.S.; Rodgers, B.R.; Brown, C.H.; Carlson, P.K.; Gambill, W.R.; Gilliam, T.M.; Holmes, J.M.; Krishnan, R.P.; Parsly, L.F.

1980-12-01T23:59:59.000Z

292

Game-based dynamic simulations supporting technical education and training iJOE International Journal of Online Engineering -www.i-joe.org 1  

E-Print Network [OSTI]

. SIMULATIONS AND GAMES FOR LEARNING PURPOSES The development of ICT solutions has allowed for more complex and advanced representations of learning material. In this context, dynamic simulators can be regardedGame-based dynamic simulations supporting technical education and training iJOE International

Foss, Bjarne A.

293

Decision making technical support study for the US Army's Chemical Stockpile Disposal Program  

SciTech Connect (OSTI)

This report examines the adequacy of current command and control systems designed to make timely decisions that would enable sufficient warning and protective response to an accident at the Edgewood area of Aberdeen Proving Ground (APG), Maryland, and at Pine Bluff Arsenal (PBA), Arkansas. Institutional procedures designed to facilitate rapid accident assessment, characterization, warning, notification, and response after the onset of an emergency and computer-assisted decision-making aids designed to provide salient information to on- and-off-post emergency responders are examined. The character of emergency decision making at APG and PBA, as well as potential needs for improvements to decision-making practices, procedures, and automated decision-support systems (ADSSs), are described and recommendations are offered to guide equipment acquisition and improve on- and off-post command and control relationships. We recommend that (1) a continued effort be made to integrate on- and off-post command control, and decision-making procedures to permit rapid decision making; (2) the pathways for alert and notification among on- and off-post officials be improved and that responsibilities and chain of command among off-post agencies be clarified; (3) greater attention be given to organizational and social context factors that affect the adequacy of response and the likelihood that decision-making systems will work as intended; and (4) faster improvements be made to on-post ADSSs being developed at APG and PBA, which hold considerable promise for depicting vast amounts of information. Phased development and procurement of computer-assisted decision-making tools should be undertaken to balance immediate needs against available resources and to ensure flexibility, equity among sites, and compatibility among on- and off-post systems. 112 refs., 6 tabs.

Feldman, D.L.; Dobson, J.E.

1990-08-01T23:59:59.000Z

294

TECHNICAL BASIS DOCUMENT OF MARSSIM FIELD CALIBRATION FOR QUANTIFICATION OF CS-137 VOLUMETRICALLY CONTAMINATED SOILS IN THE BC CONTROLLED AREA USING 2 BY 2 SODIUM IODIDE DETECTORS  

SciTech Connect (OSTI)

The purpose of this paper is to provide the Technical Basis and Documentation for Field Calibrations of radiation measurement equipment for use in the MARSSIM Seeping Surveys of the BC Controlled Area (BCCA). The Be Controlled Area is bounded on tt1e north by (but does not include) the BCCribs & Trenches and is bounded on the south by Army Loop Road. Parts of the BC Controlled Area are posted as a Contamination Area and the remainder is posted as a Soil Contamination Area. The area is approximately 13 square miles and divided into three zones (Zone A , Zone B. and Zone C). A map from reference 1 which shows the 3 zones is attached. The MARSSIM Scoping Surveys are intended 10 better identify the boundaries of the three zones based on the volumetric (pCi/g) contamination levels in the soil. The MARSSIM Field Calibration. reference 2. of radiation survey instrumentation will determine the Minimum Detectable Concentration (MDC) and an algorithm for converting counts to pCi/g. The instrumentation and corresponding results are not intended for occupational radiation protection decisions or for the release of property per DOE Order 5400.5.

PAPPIN JL

2007-10-26T23:59:59.000Z

295

Corrective Action Decision Document for Corrective Action Unit 5: Landfills, Nevada Test Site, Nevada: Revision No. 0 (with Record of Technical Change No. 1)  

SciTech Connect (OSTI)

This Corrective Action Decision Document identifies and rationalizes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office's selection of a recommended corrective action alternative (CAA) appropriate to facilitate the closure of Corrective Action (CAU) 5: Landfills, Nevada Test Site (NTS), Nevada, under the Federal Facility Agreement and Consent Order. Located in Areas 5, 6, 12, 20, and 23 of the NTS, CAU 5 is comprised of eight corrective action sites (CASs). The corrective action investigation (CAI) of CAU 5 was conducted from October 7, 2002 through January 30, 2003, with geophysical surveys completed from March 6 through May 8, 2002, and topographic surveys conducted from March 11 through April 29, 2003. Contaminants of concern (COCs) were identified only at CAS 12-15-01. Those COCs included total petroleum hydrocarbons and volatile organic compounds. Based on the evaluation of analytical data from the CAI, review of future and current operations in Areas 5, 6, 12, 20, and 23 of the Nevada Test Site, and the detailed and comparative analysis of the potential CAAs, the following single alternative was developed for consideration. Close in Place with Administrative Controls is the recommended alternative for all of the CASs in CAU 5. This alternative was judged to meet all requirements for the technical components evaluated. Additionally, the alternative meets all applicable state and federal regulations for closure of the sites and will eliminate inadvertent intrusion into landfills at CAU 5.

U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office

2003-10-24T23:59:59.000Z

296

GPHS-RTGs in support of the Cassini Mission. Semi annual technical progress report, 1 April 1996--29 September 1996  

SciTech Connect (OSTI)

This technical progress report discusses work on the Radioisotope Generators and Ancillary Activities for the Cassini spacecraft. The Cassini spacecraft is expected to launch in October 1997, and will explore Saturn and its moons. This progress report discusses issues in: spacecraft integration and liason, engineering support, safety, qualified unicouple fabrication, ETG fabrication and testing, ground support equipment, RTG shipping and launch support, designs, reviews and mission application. Safety analysis of the RTGs during reentry and launch accidents are covered. This report covers the period of April 1 to September 29, 1996.

NONE

1996-10-20T23:59:59.000Z

297

A Roadmap and Discussion of Issues for Physics Analyses Required to Support Plutonium Disposition in VVER-1000 Reactors  

SciTech Connect (OSTI)

The purpose of this report is to document the physics analyses that must be performed to successfully disposition weapons-usable plutonium in VVER-1000 reactors in the Russian Federation. The report is a document to support programmatic and financial planning. It does not include documentation of the technical procedures by which physics analyses are performed, nor are the results of any analyses included.

Primm, R.T.; Drischler, J.D.; Pavlovichev, A.M. Styrine, Y.A.

2000-06-01T23:59:59.000Z

298

Academic Information Technical Support  

E-Print Network [OSTI]

& expensive) #12;Sedimentology&Palaeontology Chris Grimshaw · In charge of Palynology lab, sediment preparation, fossil collections entomology preparation and project room areas. · In sedimentology we provide

Hickman, Mark

299

TECHNICAL BASIS FOR DOE STANDARD 3013 EQUIVALENCY SUPPORTING REDUCED TEMPERATURE STABILIZATION OF OXALATE-DERIVED PLUTONIUM DIOXIDE PRODUCED BY THE HB-LINE FACILITY AT SAVANNAH RIVER SITE  

SciTech Connect (OSTI)

This report documents the technical basis for determining that stabilizing highpurity PuO{sub 2} derived from oxalate precipitation at the SRS HB-Line facility at a minimum of 625 {degree}C for at least four hours in an oxidizing atmosphere is equivalent to stabilizing at a minimum of 950 {degree}C for at least two hours as regards meeting the objectives of stabilization defined by DOE-STD-3013 if the material is handled in a way to prevent excessive absorption of water.

Duffey, J. M.; Livingston, R. R.; Berg, J. M.; Veirs, D. K.

2013-02-06T23:59:59.000Z

300

Technical Consultant Report Template | Department of Energy  

Energy Savers [EERE]

C3d Technical Consultant Report Template.pdf More Documents & Publications External Independent Review (EIR) Report Template Technical Consultant Contract Evaluation Consultant RFP...

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Federal Energy Management Program (FEMP) Technical Assistance...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

(FEMP) Technical Assistance Request Portal User Guide Federal Energy Management Program (FEMP) Technical Assistance Request Portal User Guide Document explains how to navigate the...

302

A workshop on developing risk assessment methods for medical use of radioactive material. Volume 2: Supporting documents  

SciTech Connect (OSTI)

A workshop was held at the Idaho National Engineering Laboratory, August 16--18, 1994 on the topic of risk assessment on medical devices that use radioactive isotopes. Its purpose was to review past efforts to develop a risk assessment methodology to evaluate these devices, and to develop a program plan and a scoping document for future methodology development. This report contains presentation material and a transcript of the workshop. Participants included experts in the fields of radiation oncology, medical physics, risk assessment, human-error analysis, and human factors. Staff from the US Nuclear Regulatory Commission (NRC) associated with the regulation of medical uses of radioactive materials and with research into risk-assessment methods participated in the workshop. The workshop participants concurred in NRC`s intended use of risk assessment as an important technology in the development of regulations for the medical use of radioactive material and encouraged the NRC to proceed rapidly with a pilot study. Specific recommendations are included in the executive summary and the body of this report.

Tortorelli, J.P. [ed.] [Lockheed Idaho Technologies Co., Idaho Falls, ID (United States)

1995-08-01T23:59:59.000Z

303

The Future of Technical Assistance, Funding and Finding Alternatives  

E-Print Network [OSTI]

? Tools ? Local and individual technical support ? Budget analysis for operations and maintenance ? Cost analysis and management ? Financial alternatives ? Grant writing ? Construction and retrofit alternatives ? Back office Putting an energy...The Future of Technical Assistance, Funding and Financing Alternatives Rich Oliver, McKinstry More ?no cost or at risk? assistance in Texas than ever before ? Mentoring by Private Sector ? Education and outreach services ? Documents...

Oliver, R.

2011-01-01T23:59:59.000Z

304

TECHNICAL BASIS FOR DOE STANDARD 3013 EQUIVALENCY SUPPORTING REDUCED TEMPERATURE STABILIZATION OF OXALATE-DERIVED PLUTONIUM OXIDE PRODUCED BY THE HB-LINE FACILITY AT SAVANNAH RIVER SITE  

SciTech Connect (OSTI)

The HB-Line (HBL) facility at the Savannah River Site (SRS) is designed to produce high-purity plutonium dioxide (PuO{sub 2}) which is suitable for future use in production of Mixed Oxide (MOX) fuel. The MOX Fuel Fabrication Facility (MFFF) requires PuO{sub 2} feed to be packaged per the U.S. Department of Energy (DOE) Standard 3013 (DOE-STD-3013) to comply with the facility's safety basis. The stabilization conditions imposed by DOE-STD-3013 for PuO{sub 2} (i.e., 950 C for 2 hours) preclude use of the HBL PuO{sub 2} in direct fuel fabrication and reduce the value of the HBL product as MFFF feedstock. Consequently, HBL initiated a technical evaluation to define acceptable operating conditions for production of high-purity PuO{sub 2} that fulfills the DOE-STD-3013 criteria for safe storage. The purpose of this document is to demonstrate that within the defined operating conditions, the HBL process will be equivalent for meeting the requirements of the DOE-STD-3013 stabilization process for plutonium-bearing materials from the DOE complex. The proposed 3013 equivalency reduces the prescribed stabilization temperature for high-purity PuO{sub 2} from oxalate precipitation processes from 950 C to 640 C and places a limit of 60% on the relative humidity (RH) at the lowest material temperature. The equivalency is limited to material produced using the HBL established flow sheet, for example, nitric acid anion exchange and Pu(IV) direct strike oxalate precipitation with stabilization at a minimum temperature of 640 C for four hours (h). The product purity must meet the MFFF acceptance criteria of 23,600 {micro}g/g Pu (i.e., 2.1 wt %) total impurities and chloride content less than 250 {micro}g/g of Pu. All other stabilization and packaging criteria identified by DOE-STD-3013-2012 or earlier revisions of the standard apply. Based on the evaluation of test data discussed in this document, the expert judgment of the authors supports packaging the HBL product under a 3013 equivalency. Under the defined process conditions and associated material specifications, the high-purity PuO{sub 2} produced in HBL presents no unique safety concerns for packaging or storage in the 3013 required configuration. The PuO{sub 2} produced using the HBL flow sheet conditions will have a higher specific surface area (SSA) than PuO{sub 2} stabilized at 950 C and, consequently, under identical conditions will adsorb more water from the atmosphere. The greatest challenge to HBL operators will be controlling moisture content below 0.5 wt %. However, even at the 0.5 wt % moisture limit, the maximum acceptable pressure of a stoichiometric mixture of hydrogen and oxygen in the 3013 container is greater than the maximum possible pressure for the HBL PuO{sub 2} product.

Duffey, J.; Livingston, R.; Berg, J.; Veirs, D.

2012-07-02T23:59:59.000Z

305

American Recovery and Reinvestment Act (ARRA) FEMP Technical Assistance Federal Aviation Administration Project 209 - Control Tower and Support Building, Las Vegas, NV  

SciTech Connect (OSTI)

This report represents findings of a design review team that evaluated construction documents (at the 70% level) and operating specifications for a new control tower and support building that will be built in Las Vegas, Nevada by the Federal Aviation Administration (FAA). The focus of the review was to identify measures that could be incorporated into the final design and operating specification that would result in additional energy savings for the FAA that would not have otherwise occurred.

Arends, J.; Sandusky, William F.

2010-03-31T23:59:59.000Z

306

American Recovery and Reinvestment Act (ARRA) FEMP Technical Assistance Federal Aviation Administration – Project 209 Control Tower and Support Building Oakland, CA  

SciTech Connect (OSTI)

This report represents findings of a design review team that evaluated construction documents (at the 70% level) and operating specifications for a new control tower and support building that will be build at Oakland, California by the Federal Aviation Administration (FAA). The focus of the review was to identify measures that could be incorporated into the final design and operating specification that would result in additional energy savings for the FAA that would not have otherwise occurred.

Arends, J.; Sandusky, William F.

2010-03-01T23:59:59.000Z

307

INTERNATIONAL STUDENT FINANCIAL DOCUMENTATION FORM  

E-Print Network [OSTI]

INTERNATIONAL STUDENT FINANCIAL DOCUMENTATION FORM Please complete this form if you this form and supporting financial documents after you have received your admissions decision. To receive will come from that source. Please attach supporting financial support documents that are less than six

Barrash, Warren

308

INTERNATIONAL STUDENT FINANCIAL DOCUMENTATION FORM  

E-Print Network [OSTI]

INTERNATIONAL STUDENT FINANCIAL DOCUMENTATION FORM Please complete this form if you this form and supporting financial documents after you have received your admissions decision. To receive will come from that source. Please attach original supporting financial support documents, issued in English

Barrash, Warren

309

Technical Fact Sheets  

Broader source: Energy.gov [DOE]

Technical Fact Sheets (TFS) provide summary-level information on the impact of new, deployed, applied, and/or planned technical approaches supporting EM cleanup projects.  The TFS is presented as a...

310

1993 DOE technical standards managers workshop: Proceedings  

SciTech Connect (OSTI)

This workshop is focused on the benefits of the DOE technical standards program, which is focused toward the preferred use of non-Government standards for DOE activities and the development of DOE technical standards when non-Government standards are not available or are inappropriate. One goal of the program is to replace redundant site-specific standards with more universally accepted documents that have been scrutinized by experts. This replacement is discussed at the workshop along with the problems encountered and solutions found. The workshop provided an opportunity for geographically dispersed people to meet and advance their standards knowledge and efforts to support the program. Safety issues have been the driving force behind the program to date. Several companies offer products and services that support the development, processing, and retrieval of standards. This document mostly comprise vugraphs.

Not Available

1993-12-31T23:59:59.000Z

311

GPHS-RTGs in support of the Cassini Mission. Semiannual technical progress report, 27 September 1993--27 March 1994  

SciTech Connect (OSTI)

This report is organized by the program task structure as follows: (1) spacecraft integration and liaison; (2) engineering support; (3) safety; (4) qualified unicouple fabrication; (5) ETG fabrication, assembly, and test; (6) ground support equipment (GSE); (7) RTG shipping and launch support; (8) designs, reviews, and mission applications; (9) project management, quality assurance and reliability, contract changes, non-capital CAGO acquisition, and CAGO maintenance; and (H) contractor acquired government owned property (CAGO) acquisition.

Not Available

1994-04-24T23:59:59.000Z

312

Final Report. SFAA No. DEFC02-98CH10961. Technical assistance for joint implementation and other supporting mechanisms and measures for greenhouse gas emissions mitigation  

SciTech Connect (OSTI)

IIEC, a division of CERF, has developed an extensive base of experience implementing activities that support climate action by developing USIJI projects in transitional countries within Asia, Latin America, Central and Eastern Europe, and southern Africa. IIEC has been able to provide a range of technical and policy assistance to governments and industry in support of sustainable energy use. IIEC continues to work in key countries with local partners to develop and implement energy efficiency policies and standards, develop site-specific projects, and assist governing bodies to establish national priorities and evaluation criteria for approving GHG-mitigation projects. As part of this project, IIEC focused on promoting a series of activities in Thailand and South Africa in order to identify GHG mitigation projects and work within the national approval process of those countries. The sections of this report outline the activities conducted in each country in order to achieve that goal.

Knight, Denise

2001-10-15T23:59:59.000Z

313

Information Management and Supporting Documentation  

Broader source: Energy.gov [DOE]

The Paperwork Reduction Act (PRA) of 1995 requires each Federal agency to seek and obtain approval from the Office of Management and Budget (OMB) before undertaking a collection of information...

314

DOE Technical Assistance Program  

Broader source: Energy.gov (indexed) [DOE]

eere.energy.gov What is TAP? DOE's Technical Assistance Program (TAP) supports the Energy Efficiency and Conservation Block Grant Program (EECBG), the State Energy Program...

315

MONITORED GEOLOGIC REPOSITORY SYSTEMS REQUIREMENTS DOCUMENT  

SciTech Connect (OSTI)

This document establishes the Monitored Geologic Repository system requirements for the U.S. Department of Energy's (DOE's) Civilian Radioactive Waste Management System (CRWMS). These requirements are based on the ''Civilian Radioactive Waste Management System Requirements Document'' (CRD) (DOE 2004a). The ''Monitored Geologic Repository Systems Requirements Document'' (MGR-RD) is developed in accordance with LP-3.3 SQ-OCRWM, ''Preparation, Review, and Approval of Office of Repository Development Requirements Document''. As illustrated in Figure 1, the MGR-RD forms part of the DOE Office of Civilian Radioactive Waste Management Technical Requirements Baseline. Revision 0 of this document identifies requirements for the current phase of repository design that is focused on developing a preliminary design for the repository and will be included in the license application submitted to the U.S. Nuclear Regulatory Commission for a repository at Yucca Mountain in support of receiving a construction authorization and subsequent operating license. As additional information becomes available, more detailed requirements will be identified in subsequent revisions to this document.

V. Trebules

2006-06-02T23:59:59.000Z

316

Analysis of radiation exposure for naval units of Operation Crossroads. Volume 3. (Appendix B) support ships. Technical report  

SciTech Connect (OSTI)

External radiation doses are reconstructed for crews of support and target ships of Joint Task Force One at Operation CROSSROADS, 1946. Volume I describes the reconstruction methodology, which consists of modeling the radiation environment, to include the radioactivity of lagoon water, target ships, and support ship contamination; retracing ship paths through this environment; and calculating the doses to shipboard personnel. The USS RECLAIMER, a support ship, is selected as a representative ship to demonstrate this methodology. Doses for all other ships are summarized. Volume II (Appendix A) details the results for target ship personnel. Volume III (Appendix B) details the results for support ship personnel. Calculated doses for more than 36,000 personnel aboard support ships while at Bikini range from zero to 1.7 rem. Of those approximately 34,000 are less than 0.5 rem. From the models provided, doses due to target ship reboarding and doses accrued after departure from Bikini can be calculated, based on the individual circumstances of exposure.

Weitz, R.; Thomas, C.; Klemm, J.; Stuart, J.; Knowles, M.

1982-03-03T23:59:59.000Z

317

Engineering support services for the DOE/GRI coal gasification research program. Quarterly technical progress report, January-March 1982  

SciTech Connect (OSTI)

Kellogg continued to actively monitor operations at BI-GAS, Westinghouse and IGT (for peat gasification). Pilot plant/PDU test runs which were monitored and reported included BI-GAS Tests G-18, G-18A and G-18B; Westinghouse PDU Test TP-032-1 and CFSF Test TP-M003; and Peatgas Pilot Plant Test No. 5. Kellogg also monitored winterization/maintenance activities at BI-GAS and Westinghouse and precommissioning of the IGT Wet Carbonization PDU. The final report on the Hygas Data Base Evaluation was issued, while final revisions were completed for the reports concerning PDU data base evaluations of Peatgas and single-stage peat gasification. Efforts toward completion of the brochure describing the DOE/GRI Joint Program proceeded. Normal MPC activities continued. Several technical progress reports were issued during this quarter.

Bostwick, L.E.; Ethridge, T.R.; Starr, D.W.; Koneru, P.B.; Hubbard, D.A.; Shah, K.V.; Smith, M.R.; Ward, W.E.; Wong, E.W.

1982-05-01T23:59:59.000Z

318

Facility design philosophy: Tank Waste Remediation System Process support and infrastructure definition  

SciTech Connect (OSTI)

This report documents the current facility design philosophy for the Tank Waste Remediation System (TWRS) process support and infrastructure definition. The Tank Waste Remediation System Facility Configuration Study (FCS) initially documented the identification and definition of support functions and infrastructure essential to the TWRS processing mission. Since the issuance of the FCS, the Westinghouse Hanford Company (WHC) has proceeded to develop information and requirements essential for the technical definition of the TWRS treatment processing programs.

Leach, C.E.; Galbraith, J.D. [Westinghouse Hanford Co., Richland, WA (United States); Grant, P.R.; Francuz, D.J.; Schroeder, P.J. [Fluor Daniel, Inc., Richland, WA (United States)

1995-11-01T23:59:59.000Z

319

Technical Support for China's Village Electrification Program: Cooperative Research and Development Final Report, CRADA number CRD-07-00235  

SciTech Connect (OSTI)

This work has two main goals: First, it provides for the analysis of data collected from systems developed in the previous phase of China's rural power program, the Township Electrification Program Second, it will comprise joint IEE-NREL work in support of the upcoming phase, 'Electrification of Unelectrified Areas'.

Kline, D.

2010-07-01T23:59:59.000Z

320

GPHS-RTGs in support of the Cassini Mission. Semi annual technical report, March 31, 1997--September 28, 1997  

SciTech Connect (OSTI)

This progress report describes work on the Radioisotope Thermoelectric Generators and Ancillary Activities carried out as part of the Cassini project. Seperate sections of the report describe activities carried out in support of different tasks assigned as part of this contract.

NONE

1997-10-20T23:59:59.000Z

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

FINAL TECHNICAL REPORT: Request for support of the 11th Workshop on the Physics of Dusty Plasmas  

SciTech Connect (OSTI)

This grant supported the publication of student papers that were presented at the 11th Workshop on the Physics of Dusty Plasmas. Papers were published in a Special Issue of the IEEE Transactions on Plasma Science, Vol. 32, Issue 2 in April, 2007.

Edward Thomas

2009-05-21T23:59:59.000Z

322

STEP Energy Coach and Technical Consultant Job Descriptions ...  

Energy Savers [EERE]

Consultant Job Descriptions.pdf More Documents & Publications Technical Consultant RFP Tool Kit Framework: Small Town University Energy Program (STEP) Technical Consultant...

323

Hanford analytical services quality assurance requirements documents  

SciTech Connect (OSTI)

Hanford Analytical Services Quality Assurance Requirements Document (HASQARD) is issued by the Analytical Services, Program of the Waste Management Division, US Department of Energy (US DOE), Richland Operations Office (DOE-RL). The HASQARD establishes quality requirements in response to DOE Order 5700.6C (DOE 1991b). The HASQARD is designed to meet the needs of DOE-RL for maintaining a consistent level of quality for sampling and field and laboratory analytical services provided by contractor and commercial field and laboratory analytical operations. The HASQARD serves as the quality basis for all sampling and field/laboratory analytical services provided to DOE-RL through the Analytical Services Program of the Waste Management Division in support of Hanford Site environmental cleanup efforts. This includes work performed by contractor and commercial laboratories and covers radiological and nonradiological analyses. The HASQARD applies to field sampling, field analysis, and research and development activities that support work conducted under the Hanford Federal Facility Agreement and Consent Order Tri-Party Agreement and regulatory permit applications and applicable permit requirements described in subsections of this volume. The HASQARD applies to work done to support process chemistry analysis (e.g., ongoing site waste treatment and characterization operations) and research and development projects related to Hanford Site environmental cleanup activities. This ensures a uniform quality umbrella to analytical site activities predicated on the concepts contained in the HASQARD. Using HASQARD will ensure data of known quality and technical defensibility of the methods used to obtain that data. The HASQARD is made up of four volumes: Volume 1, Administrative Requirements; Volume 2, Sampling Technical Requirements; Volume 3, Field Analytical Technical Requirements; and Volume 4, Laboratory Technical Requirements. Volume 1 describes the administrative requirements applicable to each of the other three volumes and is intended to be used in conjunction with the technical volumes.

Hyatt, J.E.

1997-09-25T23:59:59.000Z

324

CO hydrogenation and adsorption studies on supported nickel SMSI catalysts. Technical report no. 42, 1 January-31 December 1985  

SciTech Connect (OSTI)

The uptake of CO by Ni/TiO2 and Ni/Ti/sub 2/O/sub 3/ was investigated at 25 and 125 C following low-temperature (LT = 250 C) and high-temperature (HT = 450 C) reduction. Infrared spectroscopy was used to identify the onset of nickel carbonyl (Ni(CO)/sub 4/) formation under various conditions of temperature and pressure. The CO uptake data were modeled using the Langmuir equation for isothermal adsorption. Monolayer coverages and equilibrium constants for CO adsorption were obtained from the uptake data. Carbon monoxide monolayer coverages were not affected by the reduction temperature of either Ni/TiO/sub 2/ or Ni/Ti/sub 2/O/sub 3/. Methanation activity at 275C was approximately a factor of 2 greater for the Ni/TiO/sub 2/ (LT) than the NiTiO/sub 2/ (HT) catalyst. This correlated well with the relative strength of the CO-metal surface bond, which also decreased by a factor of approximately 2. These findings suggest that the enhanced methanation rate observed on TiO/sub 2/ supported catalysts is not due to the presence or absence of a strong metal-support interaction condition of the TiO/sub 2/ but to other properties of TiO/sub 2/ as compared to other supports.

Fang, S.M.; White, J.M.; Campione, T.J.; Ekerdt, J.G.

1985-01-01T23:59:59.000Z

325

Document Reviews  

Broader source: Energy.gov [DOE]

The Office of Document Reviews, within the Office of Health, Safety and Security information and document declassification efforts promote the release of information needed by an informed citizenry...

326

Risk-assessment-methodology development for waste isolation in geologic media. Technical review of documents NUREG/CR-0394, NUREG/CR-0424, NUREG/CR-0458  

SciTech Connect (OSTI)

A review of five documents that were prepared for the USNRC by Sandia Laboratories is presented in this report. The documents covered in the present review include: NUREG/CR-1262, NUREG/CR-1376, NUREG/CR-1377, NUREG/CR-1397 and NUREG/CR-1608. This constitutes the second phase of the review; the first phase was reported in Volume 1 of NUREG/CR-1672, November 1980. Two of the documents concern simplified computational methods illustrative of the calculations necessary to produce a response surface. Three of the reports pertain to statistical methods, including the application of Latin hypercube Sampling (LHS). The following observations have been made relative to the above reports: (1) the reports are, in general, difficult to read, due, in part, to unnecessarily complicated notation and lack of adequate explanation and examples, (2) the relationship of the work to similar work in the US and abroad is not discussed, and (3) limitations of the LHS method are not discussed in sufficient depth. The Sandia's response to this review is published as NUREG/CR-2428. Volume 1 is scheduled for completion in June 1982.

Stevens, C.A.; Fullwood, R.R.; Basin, S.L.

1980-11-01T23:59:59.000Z

327

GPHS-RTGs in support of the Cassini RTG Program. Final technical report, January 11, 1991--April 30, 1998  

SciTech Connect (OSTI)

As noted in the historical summary, this program encountered a number of changes in direction, schedule, and scope over the period 11 January 1991 to 31 December 1998. The report provides a comprehensive summary of all the varied aspects of the program over its seven and a quarter years, and highlights those aspects that provide information beneficial to future radioisotope programs. In addition to summarizing the scope of the Cassini GPHS-RTG Program provided as background, the introduction includes a discussion of the scope of the final report and offers reference sources for information on those topics not covered. Much of the design heritage of the GPHS-RTG comes from the Multi-Hundred Watt (MHW) RTGs used on the Lincoln Experimental Satellites (LES) 8/9 and Voyager spacecraft. The design utilized for the Cassini program was developed, in large part, under the GPHS-RTG program which produced the Galileo and Ulysses RTGs. Reports from those programs included detailed documentation of the design, development, and testing of converter components and full converters that were identical to, or similar to, components used in the Cassini program. Where such information is available in previous reports, it is not repeated here.

NONE

1998-08-01T23:59:59.000Z

328

Vice President, Engineering and Technical Services  

Broader source: Energy.gov [DOE]

The Engineering and Technical Services organization is responsible for implementing the transmission capital program, providing technical support for the transmission maintenance program and...

329

Social Research Data Documentation, Management, and  

E-Print Network [OSTI]

Social Research Data Documentation, Management, and Technical Implementation at SFB 882 SFB 882 Pietsch, Christian Meyer, Johanna Vompras, and Stefan Liebig Social Research Data Documentation, Management, and Technical Implementation within the SFB 882 SFB 882 Working Paper Series, No. 16 DFG Research

Moeller, Ralf

330

Technical Brief  

E-Print Network [OSTI]

ii iiiFOREWARD The Depleted Uranium Technical Brief is designed to convey available information and knowledge about depleted uranium to EPA Remedial Project Managers, On-Scene Coordinators, contractors, and other Agency managers involved with the remediation of sites contaminated with this material. It addresses relative questions regarding the chemical and radiological health concerns involved with depleted uranium in the environment. This technical brief was developed to address the common misconception that depleted uranium represents only a radiological health hazard. It provides accepted data and references to additional sources for both the radiological and chemical characteristics, health risk as well as references for both the monitoring and measurement and applicable treatment techniques for depleted uranium. Please Note: This document has been changed from the original publication dated

Depleted Uranium; Brian Littleton

2006-01-01T23:59:59.000Z

331

Approaches to the assessment of injuries to soil arising from discharges of hazardous substances and oil: Type B, Technical information document  

SciTech Connect (OSTI)

Methods for determining the nature and magnitude of injury to the following natural resources are described for: soil chemical characteristics (acidity or pH, cation exchange capacity, percent base saturation, salinity); soil physical characteristics (porosity, water holding capacity, aggregate stability); biological characteristics (microbial activities, invertebrate activities, vegetation); and contaminant transport potential (leaching, food chain). In addition, this document explains how injuries to the soil resource can be translated into a reduction in service provided by that soil and how to determine soil recovery potential. That portion of 43 CFR Part 11 that pertains to the soils portion of the geologic resource is explained.

Van Voris, P.; Dawson, G.W.; Fredrickson, J.K.; Cataldo, D.A.; Rogers, L.E.; Novich, C.M.; Meuser, J.

1987-06-01T23:59:59.000Z

332

Supported by: U.S. National Science Foundation (NSF), and Scientific and Technical Research Council of Turkey (TUBITAK) Contact information: Marek Zreda: marek@hwr.arizona.edu; Attila Ciner: aciner@hacettepe.edu.tr; Serdar Bayari: serdar@hacettepe.edu.tr;  

E-Print Network [OSTI]

Supported by: U.S. National Science Foundation (NSF), and Scientific and Technical Research Council factors, Goldschmidt Conference, Moscow, Idaho, May 2005), with the following production rates: 75

Zreda, Marek

333

High temperature turbine technology program. Phase II. Technology test and support studies. Annual technical progress report, January 1, 1979-December 31, 1979  

SciTech Connect (OSTI)

Work performed on the High Temperature Turbine Technology Program, Phase II - Technology Test and Support Studies during the period from January 1, 1979 through December 31, 1979 is summarized. Objectives of the program elements as well as technical progress and problems encountered during this Phase II annual reporting period are presented. Progress on design, fabrication and checkout of test facilities and test rigs is described. LP turbine cascade tests were concluded. 350 hours of testing were conducted on the LP rig engine first with clean distillate fuel and then with fly ash particulates injected into the hot gas stream. Design and fabrication of the turbine spool technology rig components are described. TSTR 60/sup 0/ sector combustor rig fabrication and testing are reviewed. Progress in the design and fabrication of TSTR cascade rig components for operation on both distillate fuel and low Btu gas is described. The new coal-derived gaseous fuel synthesizing facility is reviewed. Results and future plans for the supporting metallurgical programs are discussed.

Not Available

1980-01-01T23:59:59.000Z

334

B PLANT DOCUMENTED SAFETY ANALYSIS  

SciTech Connect (OSTI)

This document provides the documented safety analysis (DSA) and Central Plateau Remediation Project (CP) requirements that apply to surveillance and maintenance (S&M) activities at the 221-B Canyon Building and ancillary support structures (B Plant). The document replaces BHI-010582, Documented Safety Analysis for the B-Plant Facility. The B Plant is non-operational, deactivated and undergoing long term S&M prior to decontamination and decommissioning (D&D). This DSA is compliant with 10 CFR 830, Nuclear Safety Management, Subpart B, ''Safety Basis Requirements.'' The DSA was developed in accordance with U.S. Department of Energy (DOE) standard DOE-STD-1120-98, Integration of Environment, Safety, and Health into Facility Disposition Activities (DOE 1998) per Table 2 of 10 CFR 830 Appendix A, DOE Richland Operation Office (RL) direction (02-ABD-0053, Fluor Hanford Nuclear Safety Basis Strategy and Criteria) for facilities in long term S&M, and RL Direction (02-ABD-0091, ''FHI Nuclear Safety Expectations for Nuclear Facilities in Surveillance and Maintenance''). A crosswalk was prepared to identify potential inconsistencies between the previous B Plant safety analysis and DOE-STD-1120-98 guidance. In general, the safety analysis met the criteria of DOE-STD-1120-98. Some format and content changes have been made, including incorporating recent facility modifications and updating the evaluation guidelines and control selection criteria in accordance with RL direction (02-ABD-0053). The facility fire hazard analysis (FHA) and Technical Safety Requirements (TSR) are appended to this DSA as an aid to the users, to minimize editorial redundancy, and to provide an efficient basis for update.

DODD, E.N.; KERR, N.R.

2003-08-01T23:59:59.000Z

335

500 Year Documentation Francis T. Marchese  

E-Print Network [OSTI]

Documentation, Design, Management. Keywords Digital art, conservation, requirements engineering. 1. THE PROBLEM500 Year Documentation Francis T. Marchese Pace University Computer Science Department New York, NY the requirements for creating documentation that will support an artwork's adaptation to future technology

Marchese, Francis

336

Lead Emissions from the Use of Leaded Aviation Gasoline in the United States: Technical Support Document (EPA420-R-08-020)  

National Nuclear Security Administration (NNSA)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarlyEnergyDepartmentNationalRestart of the Review of theOFFICEACMEFUTURE MOBILITYMarchUnitedrLead

337

Transportation System Requirements Document  

SciTech Connect (OSTI)

This Transportation System Requirements Document (Trans-SRD) describes the functions to be performed by and the technical requirements for the Transportation System to transport spent nuclear fuel (SNF) and high-level radioactive waste (HLW) from Purchaser and Producer sites to a Civilian Radioactive Waste Management System (CRWMS) site, and between CRWMS sites. The purpose of this document is to define the system-level requirements for Transportation consistent with the CRWMS Requirement Document (CRD). These requirements include design and operations requirements to the extent they impact on the development of the physical segments of Transportation. The document also presents an overall description of Transportation, its functions, its segments, and the requirements allocated to the segments and the system-level interfaces with Transportation. The interface identification and description are published in the CRWMS Interface Specification.

Not Available

1993-09-01T23:59:59.000Z

338

Contracts for field projects and supporting research on enhanced oil recovery. Quarterly technical progress report, July 1, 1995--September 30, 1995  

SciTech Connect (OSTI)

This document presents brief descriptions of research programs concerned with enhanced oil recovery.

NONE

1996-10-01T23:59:59.000Z

339

Monitored Geologic Repository Project Description Document  

SciTech Connect (OSTI)

The primary objective of the Monitored Geologic Repository Project Description Document (PDD) is to allocate the functions, requirements, and assumptions to the systems at Level 5 of the Civilian Radioactive Waste Management System (CRWMS) architecture identified in Section 4. It provides traceability of the requirements to those contained in Section 3 of the ''Monitored Geologic Repository Requirements Document'' (MGR RD) (CRWMS M&O 2000b) and other higher-level requirements documents. In addition, the PDD allocates design related assumptions to work products of non-design organizations. The document provides Monitored Geologic Repository (MGR) engineering design basis in support of design and performance assessment in preparing for the Site Recommendation (SR) and License Application (LA) milestones. The engineering design basis documented in the PDD is to be captured in the System Description Documents (SDDs) which address each of the systems at Level 5 of the CRWMS architecture. The design engineers obtain the engineering design basis from the SDDs and by reference from the SDDs to the PDD. The design organizations and other organizations will obtain design related assumptions directly from the PDD. These organizations may establish additional assumptions for their individual activities, but such assumptions are not to conflict with the assumptions in the PDD. The PDD will serve as the primary link between the engineering design basis captured in the SDDs and the design requirements captured in U.S. Department of Energy (DOE) documents. The approved PDD is placed under Level 3 baseline control by the CRWMS Management and Operating Contractor (M&O) and the following portions of the PDD constitute the Technical Design Baseline for the MGR: the design characteristics listed in Table 2-1, the MGR Architecture (Section 4.1),the Engineering Design Bases (Section 5), and the Controlled Project Assumptions (Section 6).

P. Curry

2000-06-01T23:59:59.000Z

340

INTERNATIONAL STUDENT FINANCIAL DOCUMENTATION FORM  

E-Print Network [OSTI]

INTERNATIONAL STUDENT FINANCIAL DOCUMENTATION FORM This form is not an application for financial assistance. This form is REQUIRED before we can provide immigration documents, even if your government, photocopied or faxed supporting financial documents. **List your name as it appears on your passport** Family

Barrash, Warren

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Technical basis for external dosimetry at the Waste Isolation Pilot Plant (WIPP)  

SciTech Connect (OSTI)

The WIPP External Dosimetry Program, administered by Westinghouse Electric Corporation, Waste Isolation Division, for the US Department of Energy (DOE), provides external dosimetry support services for operations at the Waste Isolation Pilot Plant (WIPP) Site. These operations include the receipt, experimentation with, storage, and disposal of transuranic (TRU) wastes. This document describes the technical basis for the WIPP External Radiation Dosimetry Program. The purposes of this document are to: (1) provide assurance that the WIPP External Radiation Dosimetry Program is in compliance with all regulatory requirements, (2) provide assurance that the WIPP External Radiation Dosimetry Program is derived from a sound technical base, (3) serve as a technical reference for radiation protection personnel, and (4) aid in identifying and planning for future needs. The external radiation exposure fields are those that are documented in the WIPP Final Safety Analysis Report.

Bradley, E.W. [Science Applications International Corp., Oak Ridge, TN (United States); Wu, C.F.; Goff, T.E. [Westinghouse Electric Corp., Carlsbad, NM (United States). Waste Isolation Div.

1993-12-31T23:59:59.000Z

342

Contracts for field projects and supporting research on enhanced oil recovery. Quarterly technical progress report, October 1994--December 1994. Progress review No. 81  

SciTech Connect (OSTI)

This document consists of a publications list for field projects and brief descriptions of research projects on enhanced petroleum recovery.

NONE

1996-03-01T23:59:59.000Z

343

Space Conditioning Standing Technical Committee Strategic Plan...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Committee Strategic Plan Space Conditioning Standing Technical Committee Strategic Plan This strategic plan document outlines the gaps, barriers, and opportunities identified by...

344

Documentation of Special Circumstances FINANCIAL AID INFORMATION 2009-2010  

E-Print Network [OSTI]

Documentation of Special Circumstances FINANCIAL AID INFORMATION 2009-2010 Brandeis University, but need to be documented before they can be included. This form gives students the opportunity to document AND ATTACH SUPPORTING DOCUMENTATION. #12;

Snider, Barry B.

345

Technology, safety and costs of decommissioning a reference boiling water reactor power station: Technical support for decommissioning matters related to preparation of the final decommissioning rule  

SciTech Connect (OSTI)

Preparation of the final Decommissioning Rule by the Nuclear Regulatory Commission (NRC) staff has been assisted by Pacific Northwest Laboratory (PNL) staff familiar with decommissioning matters. These efforts have included updating previous cost estimates developed during the series of studies of conceptually decommissioning reference licensed nuclear facilities for inclusion in the Final Generic Environmental Impact Statement (FGEIS) on decommissioning; documenting the cost updates; evaluating the cost and dose impacts of post-TMI-2 backfits on decommissioning; developing a revised scaling formula for estimating decommissioning costs for reactor plants different in size from the reference boiling water reactor (BWR) described in the earlier study; and defining a formula for adjusting current cost estimates to reflect future escalation in labor, materials, and waste disposal costs. This report presents the results of recent PNL studies to provide supporting information in three areas concerning decommissioning of the reference BWR: updating the previous cost estimates to January 1986 dollars; assessing the cost and dose impacts of post-TMI-2 backfits; and developing a scaling formula for plants different in size than the reference plant and an escalation formula for adjusting current cost estimates for future escalation.

Konzek, G.J.; Smith, R.I.

1988-07-01T23:59:59.000Z

346

Technology, safety and costs of decommissioning a reference pressurized water reactor power station: Technical support for decommissioning matters related to preparation of the final decommissioning rule  

SciTech Connect (OSTI)

Preparation of the final Decommissioning Rule by the Nuclear Regulatory Commission (NRC) staff has been assisted by Pacific Northwest Laboratory (PNL) staff familiar with decommissioning matters. These efforts have included updating previous cost estimates developed during the series of studies on conceptually decommissioning reference licensed nuclear facilities for inclusion in the Final Generic Environmental Impact Statement (FGEIS) on decommissioning; documenting the cost updates; evaluating the cost and dose impacts of post-TMI-2 backfits on decommissioning; developing a revised scaling formula for estimating decommissioning costs for reactor plants different in size from the reference pressurized water reactor (PWR) described in the earlier study; defining a formula for adjusting current cost estimates to reflect future escalation in labor, materials, and waste disposal costs; and completing a study of recent PWR steam generator replacements to determine realistic estimates for time, costs and doses associated with steam generator removal during decommissioning. This report presents the results of recent PNL studies to provide supporting information in four areas concerning decommissioning of the reference PWR: updating the previous cost estimates to January 1986 dollars; assessing the cost and dose impacts of post-TMI-2 backfits; assessing the cost and dose impacts of recent steam generator replacements; and developing a scaling formula for plants different in size than the reference plant and an escalation formula for adjusting current cost estimates for future escalation.

Konzek, G.J.; Smith, R.I.

1988-07-01T23:59:59.000Z

347

Monitored Retrievable Storage System Requirements Document. Revision 1  

SciTech Connect (OSTI)

This Monitored Retrievable Storage System Requirements Document (MRS-SRD) describes the functions to be performed and technical requirements for a Monitored Retrievable Storage (MRS) facility subelement and the On-Site Transfer and Storage (OSTS) subelement. The MRS facility subelement provides for temporary storage, at a Civilian Radioactive Waste Management System (CRWMS) operated site, of spent nuclear fuel (SNF) contained in an NRC-approved Multi-Purpose Canister (MPC) storage mode, or other NRC-approved storage modes. The OSTS subelement provides for transfer and storage, at Purchaser sites, of spent nuclear fuel (SNF) contained in MPCs. Both the MRS facility subelement and the OSTS subelement are in support of the CRWMS. The purpose of the MRS-SRD is to define the top-level requirements for the development of the MRS facility and the OSTS. These requirements include design, operation, and decommissioning requirements to the extent they impact on the physical development of the MRS facility and the OSTS. The document also presents an overall description of the MRS facility and the OSTS, their functions (derived by extending the functional analysis documented by the Physical System Requirements (PSR) Store Waste Document), their segments, and the requirements allocated to the segments. In addition, the top-level interface requirements of the MRS facility and the OSTS are included. As such, the MRS-SRD provides the technical baseline for the MRS Safety Analysis Report (SAR) design and the OSTS Safety Analysis Report design.

Not Available

1994-03-01T23:59:59.000Z

348

GPHS-RTGs in support of the Cassini mission. Semi-annual technical report, 30 March 1992--27 September 1992  

SciTech Connect (OSTI)

The technical progress achieved during the period 30 March through 27 September 1992 on Contract DE-AC03-91SF18852.000 Radioisotope Thermoelectric Generators and Acillary Activities is described herein.

Not Available

1992-10-01T23:59:59.000Z

349

Findings of the Peer Review Panel on the Draft Reactor Risk Reference Document, NUREG-1150  

SciTech Connect (OSTI)

This report contains the finding of the /open quotes/NUREG-1150 Peer Review Panel/close quotes/ on the methodology and results presented in the Draft Reactor Risk Reference Study (NUREG-1150) and supporting documentation. The report consists of two principal parts: the chairman's report, which summarizes the principal issues of the review, and the individual members' reports, which supply the individual findings and technical details of the fourteen reviewers.

Kastenberg, W.E.; Apostolakis, G.; Bickel, J.H.; Blond, R.M.; Board, S.J.; Epstein, M.; Hofmann, P.; King, F.K.; Ostrach, S.; Reed, J.W.

1988-05-01T23:59:59.000Z

350

Draft 1992 Resource Program : Technical Report.  

SciTech Connect (OSTI)

The 1992 Resource Program will propose actions to meet future loads placed on the Bonneville Power Administration (BPA). It will also discuss and attempt to resolve resource-related policy issues. The Resource Program assesses resource availability and costs, and analyzes resource requirements and alternative ways of meeting those requirements through both conservation and generation resources. These general resource conclusions are then translated to actions for both conservation and generation. The Resource Program recommends budgets for the Office of Energy Resources for Fiscal Years (FY) 1994 and 1995. BPA`s Resource Program bears directly on an important BPA responsibility: the obligation under the Northwest Power Act{sup 3} to meet the power requirements of public and private utility and direct service industrial (DSI) customers according to their contractual agreements. BPA`s Draft 1992 Resource Program is contained in four documents: (1) 1992 Resource Program Summary; (2) Technical Report; (3) Technical Assumptions Appendix; and, (4) Conservation Implementation Plan. This volume is the Draft 1992 Resource Program Technical Report, a comprehensive document that provides supporting data and analyses for Resource Program recommendations.

United States. Bonneville Power Administration.

1992-01-01T23:59:59.000Z

351

Draft 1992 Resource Program : Technical Report.  

SciTech Connect (OSTI)

The 1992 Resource Program will propose actions to meet future loads placed on the Bonneville Power Administration (BPA). It will also discuss and attempt to resolve resource-related policy issues. The Resource Program assesses resource availability and costs, and analyzes resource requirements and alternative ways of meeting those requirements through both conservation and generation resources. These general resource conclusions are then translated to actions for both conservation and generation. The Resource Program recommends budgets for the Office of Energy Resources for Fiscal Years (FY) 1994 and 1995. BPA's Resource Program bears directly on an important BPA responsibility: the obligation under the Northwest Power Act{sup 3} to meet the power requirements of public and private utility and direct service industrial (DSI) customers according to their contractual agreements. BPA's Draft 1992 Resource Program is contained in four documents: (1) 1992 Resource Program Summary; (2) Technical Report; (3) Technical Assumptions Appendix; and, (4) Conservation Implementation Plan. This volume is the Draft 1992 Resource Program Technical Report, a comprehensive document that provides supporting data and analyses for Resource Program recommendations.

United States. Bonneville Power Administration.

1992-01-01T23:59:59.000Z

352

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

. Williams, Eun Sug Park 8. Performing Organization Report No. Report 167142-1 10. Work Unit No. (TRAIS)9. Chrysler, Ph.D. Research Scientist Texas Transportation Institute Alicia A. Williams Research Associate variables. Texas A&M students Sara Meischen and Jeff

353

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

auto travel demand on highways. The resulting traffic congestion levels, surging oil prices and route choice drawing from the 2008 Chicago Regional Household Travel Inventory (CRHTI). The empirical

354

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

SECTIONS, DATA COLLECTION, ANALYSES, AND DATA STORAGE SYSTEM 5. Report Date Published: June 2012 6 plans, and 3) field test sections. The MS Access Data Storage System, used for storing and accessing, MS Access, Data Storage System, Test Section, M-E Model 18. Distribution Statement No restrictions

355

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Center Texas Transportation Institute Kermit Black Special Assistant to the Dean of Architecture Texas A highlight. Sustainability of vehicles bought with state funds was achieved by securing commitments from. Sustainability highlights. The maintenance and operation of the vehicles are crucial to extending the use

356

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

of the art performance models and reliability concepts, from which it determines maintenance. Performing Organization Name and Address Center for Transportation Research University of Texas at Austin Transportation Center Texas Transportation Institute The Texas A&M University System College Station, Texas 77843

357

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

optimal rehabilitation and maintenance policies. In this study pavement reliability model that is able for Performance-Based Maintenance Contracts 6. Performing Organization Code 7. Author(s) Ivan Damnjanovic, Seok Transportation Center Texas Transportation Institute Texas A&M University System College Station, Texas 77843

358

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

. Performing Organization Name and Address Center for Transportation Research The University of Texas at Austin design, construction, maintenance, and user impacts throughout the analysis period. It predicts pavement performance using state-of-the-art performance models and reliability concepts, from which it determines

Texas at Austin, University of

359

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

(s) David Birrcher, Robin Tuchscherer, Matt Huizinga, Oguzhan Bayrak, Sharon Wood, and James Jirsa 8 AND SERVICEABILITY DESIGN OF REINFORCED CONCRETE DEEP BEAMS David Birrcher Robin Tuchscherer Matt Huizinga Oguzhan

Texas at Austin, University of

360

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

. A survey of the Houston dray industry and its driver workforce is then reported. Since other deep-water Project performed in cooperation with the Texas Department of Transportation and the Federal Highway: 0-5068-2 Report Date: November 2006; Revised February 2007 Project: 0-5068 Project Title: Planning

Texas at Austin, University of

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

to be opened to long-haul Mexican carriers under NAFTA. As a result of truck traffic surge, from. Recipient's Catalog No. 5. Report Date April 2007 4. Title and Subtitle Characterizing Truck Traffic in truck movements in the countries. In 2004, the Supreme Court ruled against the requirement to undertake

362

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

characterization of the decrease in shear strength with time induced by successive cycles of wetting and drying properties due to cracking. Assessment of the influence of critical precipitation events is provided. 17. Key

Texas at Austin, University of

363

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

from the State of Texas. 16. Abstract In recent years, the policy and regulatory environment passenger rail network, a better understanding of the mobility provided by short- to medium and regulatory environment for intercity passenger rail in the United States has shifted dramatically, sparking

364

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

, like person delay, fuel consumption, and mobile source emissions, were used to compare alternative Transportation Center Texas Transportation Institute The Texas A&M University System College Station, Texas 77843 in this report used eight months of travel time data (April through November 1994) available through Houston

365

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

national availability of E10. As a follow up to the 2008 Bioenergy and Alternative Fuels Scoping Study or international ethanol is more economically competitive in six Texas fuel markets. If Congress chose to repeal, Transportation Corridors, Bioenergy, Biofuels, Alternative Fuels, Economic Impacts, Transport of Alternative

366

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

of Bioenergy and Alternative Fuels on the Southwest Region's Economy and Transportation Infrastructure 6 to impact the Southwest in the near term. Ethanol is the biofuel most widely marketed at the present time reach Texas markets depending on whether the biofuel originated in American corn fields or the Brazilian

367

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

and solar panels. 17. Key Words Solar Energy, Light Emitting Diodes (LED), Intersections, Incandescent Bulbs No. 3. Recipient's Catalog No. 4. Title and Subtitle Feasibility of Solar Powered Traffic Signs. By retrofitting the signals to solar energy and switching to LED the city will see major energy and cost savings

368

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

and solar panel installation. The Phase II installation utilized a more powerful datalogger at the Mustang. Type of Report and Period Covered Project Summary Report (9/99-12/99) 12. Sponsoring Agency Name ultrasonic sensors mounted on four different bridge piers. Researchers had access to the scour and stage data

Texas at Austin, University of

369

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

. Recipient's Catalog No. 4. Title and Subtitle Phase 1 Report on the Development of Predictive Model for Bridge Deck Cracking and Strength Development 5. Report Date January 2009 6. Performing Organization Code coupled with autogenous and thermal shrinkage), can have several detrimental effects on long-term behavior

Texas at Austin, University of

370

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

creep issues. Thermal stresses also play a role in bridge deck cracking. These stresses result from. Recipient's Catalog No. 5. Report Date October 2003 4. Title and Subtitle Evaluation of Alternative Materials to Control Drying- Shrinkage Cracking in Concrete Bridge Decks 6. Performing Organization Code 7

Texas at Austin, University of

371

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

cracking. These stresses result from the heat of hydration, diurnal temperature changes, and solar any art, method, process, machine, manufacture, design or composition of matter, or any new and useful

Texas at Austin, University of

372

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

of hooked bar anchorage is also included. The review of headed reinforcement includes historical background of pertinent code provisions. The review of strut-and-tie modeling (STM) includes an historical background Classif. (of this page) Unclassified 21. No. of pages 116 22. Price Form DOT F 1700.7 (8-72) Reproduction

Texas at Austin, University of

373

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

this historical review, a survey of transit agencies regarding recent transit standards was conducted, and with the recent Standard Bus Procurement Guidelines, was investigated. Both the historical review and the survey Classif.(of this page) Unclassified 21. No. of Pages 45 22. Price Form DOT F 1700.7 (8-72) Reproduction

374

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

IN HOT-MIX ASPHALT CONSTRUCTION 5. Report Date February 2005 Resubmitted: January 2006 Published: April, and Wenting Liu 8. Performing Organization Report No. Report 0-4577-2 10. Work Unit No. (TRAIS)9. Performing IN HOT-MIX ASPHALT CONSTRUCTION by Stephen Sebesta Associate Transportation Researcher Texas

375

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Glover, and Nicolas Norboge 8. Performing Organization Report No. Report 5-6395-01-1 9. Performing Brianne Glover, J.D. Associate Transportation Researcher Texas Transportation Institute and Nicolas

376

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

(s) Stuart Anderson, Curtis Beaty, Liang Ding, David Ellis, Jon Epps, Cindy Estakhri, Brianne Glover Research Engineer Texas Transportation Institute Brianne Glover Assistant Transportation Researcher Texas

377

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Code 7. Author(s) Charles J. Glover, Guanlan Liu, Avery A. Rose, Yunwei Tong, Fan Gu, Meng Ling, Edith by Charles J. Glover, Ph.D., P.E. Professor/Research Engineer Texas A&M Transportation Institute Guanlan Liu

378

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

, particularly in wind power generation and extraction of oil and natural gas. While energy developments use datasets, and geology-related datasets. The recommendations for implementation were grouped recommendations). 17. Key Words Energy Developments, Oil and Gas, Wind Farms, Pavement, Utilities, Driveway

379

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

. Report Date April 2009 6. Performing Organization Code 7. Author(s) Jennifer Bennett and Tracy McMillan 8 Sector's Role in Public School Facility Planning by Jennifer Bennett Tracy McMillan Research Report SWUTC

380

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

Corridors, Megaregions, Rail, Truck, Fuel Efficiency, Freight Operating Costs. 18. Distribution Statement. To address this need, a truck-rail intermodal toolkit was developed for multimodal corridor analysis characteristics. The toolkit includes techniques to acquire data for simulating line-haul movements, and models

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

the impact of the built environment, transportation network attributes, and demographic characteristics association between the built enviro

382

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

strengths measured in unconsolidated-undrained, consolidated-undrained, field vane shear, and piezocone disturbance in unconsolidated-undrained tests was assessed based on values of axial strain at 75 percent of the principal stress difference at failure. While there was significant scatter in the data, unconsolidated

Texas at Austin, University of

383

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

. Researchers developed accident modification factors (AMFs) related to frontage road conversion segments Frontage Road, Frontage Road Conversion, Crash Reduction Factor, CRF, Accident Modification Factor, AMF site in Texas that remained two-way for comparison to four of the treatment (conversion) sites

384

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

16. Abstract The "container revolution" of the last forty years has altered the manner in which goes to Dr. Richard Feldman, Department of Industrial Engineering at Texas A&M University and Mr assumes no liability for the contents or use thereof. #12;iv ABSTRACT The "container revolution

385

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

mixture based on laboratory results but that the mixtures would have equivalent resistance based on field structure present challenges in terms of evaluating mixture resistance. This project focused on comparing compared. Both approaches can be used to characterize mixture fatigue resistance with relatively low

386

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

of accelerometer data, which cannot be satisfied with a typical solar panel and battery. Tiltmeters can provide-3135 10. Work Unit No. (TRAIS) 11. Contract or Grant No. Project 0-6060 12. Sponsoring Agency Name

Briaud, Jean Louis

387

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

gaps increases vehicle delay in most cases. This finding is enlightening regarding current practices No. 3. Recipient's Catalog No. 4. Title and Subtitle SUSTAINABLE INTERSECTION CONTROL TO ACCOMMODATE a model following a Poisson process that studied the intersection performance of traffic. We extended

388

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

the problems associated with unsustainable transportation practices. These cases are supplemented a cyclical process for sustainable development from finance through implementation. The final section into professional practices and paradigms. 17. Key Words Sustainable Development, Sustainability, Sustainable

389

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

contain suspended solids, metals, oil and grease, fecal coliform, and oxygen demanding organics. Highway, Springfield, Virginia 22161; www.ntis.gov. 19. Security Classif. (of report) Unclassified 20. Security Classif

Texas at Austin, University of

390

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

As the United States imports more than half of its oil and overall consumption continues to climb, the 1992 Information Service 5285 Port Royal Road Springfield, Virginia 22161 19. Security Classif.(of this report) Unclassified 20. Security Classif.(of this page) Unclassified 21. No. of Pages 54 22. Price Form DOT F 1700

391

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

been ongoing since the oil crises of the 1970s. While there are some commonalties in the regulatory 5285 Port Royal Road Springfield, Virginia 22161 19. Security Classif.(of this report) Unclassified 20. Security Classif.(of this page) Unclassified 21. No. of Pages 51 22. Price Form DOT F 1700.7 (8

392

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

that macro-economic conditions, such as prices of commodities (e.g. oil, cement and steel) affect the cost 5285 Port Royal Road Springfield, Virginia 22161 19. Security Classif.(of this report) Unclassified 20. Security Classif.(of this page) Unclassified 21. No. of Pages 174 22. Price Form DOT F 1700.7 (8

393

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

more automated, particularly in container handling, where robotics equipment may well be introduced AS THE BASELINE PORT by Arthur P. James, Ph.D Assistant Professor, Department of Maritime Administration Texas A Texas Southern University John P. Basilotto, Col. [R] Assistant Research Scientist Center for Ports

394

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

with Dr. Robin R. Murphy, Director of the Center for Robot-Assisted Search and Rescue and Professor. Gharaibeh Assistant Professor Zachry Department of Civil Engineering Texas A&M University Texas

395

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

this methodology to estimate emissions produced by trucks from Mexico crossing the El Paso-Ciudad Juarez border Idling Emissions at the El Paso - Ciudad Juarez Border Location 6. Performing Organization Code 7. Author Transportation Institute The Texas A&M University System College Station, Texas 77843-3135 11. Contract or Grant

396

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

for Carbon Sequestration Using a Controlled Environment 5. Report Date May 2012 6. Performing Organization carbon sequestration techniques are rapidly becoming part of how environmental mitigation business is conducted, not only in Texas but globally. Terrestrial carbon sequestration is the general term used

397

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

in the laboratory for different pier sizes and for a range of subcritical flow conditions. Both water level changes. Recipient's Catalog No. 4. BACKWATER EFFECTS OF PIERS IN SUBCRITICAL FLOW 5. Report Date October 2001 6 or floodplain of natural waterways. These piers will obstruct the flow and may cause an increase in water levels

Texas at Austin, University of

398

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

results in higher camber and deflections. Testing of 3/8-inch prestressing strands in precast concrete. Recipient's Catalog No. 4. Title And Subtitle Feasibility of Utilizing High-Performance Lightweight Concrete concrete in Texas prestressed concrete bridges has potential advantages and disadvantages. Advantages

Texas at Austin, University of

399

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

and hardened concrete, mortar, and paste. Additional testing was performed to investigate the cracking of steel. Recipient's Catalog No. 4. Title and Subtitle THE EFFECTS OF LIQUID NITROGEN ON CONCRETE PROPERTIES 5 was to determine the effects of liquid nitrogen cooling of fresh concrete on concrete hydration and properties

Texas at Austin, University of

400

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

concrete. Two coarse aggregate types were used in the test sections: siliceous river gravel (SRG delaminations. 17. Key Words Bonded concrete overlay, delaminations, non- destructive testing 18. Distribution. Recipient's Catalog No. 4. Title and Subtitle Evaluation of Bonded Concrete Overlay on IH 610 in Houston

Texas at Austin, University of

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

. Recipient's Catalog No. 4. Title and Subtitle Towards an Integrated Pavement Design Approach: Using HWTD Design Guide (MEPDG) to analyze and predict the effect of the variability of HMA production on rutting Pavement Design Guide (MEPDG), Hamburg Wheel Tracking Device (HWTD) 18. Distribution Statement

402

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

% of its miles using a plug-in hybrid electric vehicle (PHEV) with 40-mile all-electric-range. Households gas prices are $3.50 per gallon and electricity rates at the U.S. average of 11.2 ct per kWh, the Volt. Recipient's Catalog No. 4. Title and Subtitle PREDICTING THE MARKET POTENTIAL OF PLUG-IN ELECTRIC VEHICLES

403

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

. Recipient's Catalog No. 4. Title and Subtitle FRONTAGE ROADS IN TEXAS: A Comprehensive Assessment. 5. Report corridors suggested that land near frontage roads is associated with lower household incomes, lower, in addition to efforts by other researchers, will assist in constructing a solid, formal policy for all states

Kockelman, Kara M.

404

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

coated steels, galvanized steel, corrosion resistant steels, dual- phase steels, and stainless steels. Also included are steels coated with types of coatings (other than epoxy) and steels which use various types of paints for corrosion protection. 17. Key Words Corrosion, steel, concrete, alternative

Texas at Austin, University of

405

Technical Report Documentation Page 1. Report No.  

E-Print Network [OSTI]

consumption. Differences in emissions between non-idling modes of operation varied by pollutant. CO2 and NOx of emission control strategies. This modeling indicated that even with reductions in on-road and non eligibility for Texas Emission Reduction Program (TERP) funding to reduce NOx emissions from on-road heavy

Texas at Austin, University of

406

21st Century Truck Partnership - Roadmap and Technical White...  

Broader source: Energy.gov (indexed) [DOE]

- Roadmap and Technical White Papers Appendix of Supporting Information - 21CTP-0003, December 2006 21st Century Truck Partnership - Roadmap and Technical White Papers Appendix of...

407

US DRIVE Vehicle Systems and Analysis Technical Team Roadmap...  

Energy Savers [EERE]

Vehicle Systems and Analysis Technical Team Roadmap US DRIVE Vehicle Systems and Analysis Technical Team Roadmap VSATT provides the analytic support and subsystem characterizations...

408

Owyhee Subbasin Plan Chapter 2 Technical Assessment  

E-Print Network [OSTI]

Technical Assessment. Steven C. Vigg, Editor. Final Draft. Submitted to the Northwest Power and ConservationOwyhee Subbasin Plan Chapter 2 Technical Assessment Prepared By: The Shoshone-Paiute Tribes Program. #12;Owyhee Subbasin Plan Chapter 2 OSP Technical Assessment Final Draft May 28, 2004i Document

409

Technical support documentation for the Automated Residential Energy Standard (ARES) data base in support of proposed interim energy conservation voluntary performance standards for new non-federal residential buildings: Volume 4  

SciTech Connect (OSTI)

This report focuses on those areas where substantial improvements have been made in simulation techniques or analysis of results concerning the Automated Residential Energy Standard (ARES).

NONE

1989-09-01T23:59:59.000Z

410

POTENTIAL ENHANCEMENTS TO NATURAL ATTENUATION: LINES OF INQUIRY SUPPORTING ENHANCED PASSIVE REMEDIATION OF CHLORINATED SOLVENTS  

SciTech Connect (OSTI)

The Department of Energy (DOE) is sponsoring an initiative to facilitate efficient, effective and responsible use of Monitored Natural Attenuation (MNA) and Enhanced Passive Remediation (EPR) for chlorinated solvents. This Office of Environmental Management (EM) ''Alternative Project,'' focuses on providing scientific and policy support for MNA/EPR. A broadly representative working group of scientists supports the project along with partnerships with regulatory organizations such as the Interstate Technology and Regulatory Council and the U.S. Environmental Protection Agency (EPA). The initial product of the technical working group was a summary report that articulated the conceptual approach and central scientific tenants of the project, and that identified a prioritized listing of technical targets for field research. This report documented the process in which: (1) scientific ground rules were developed, (2) lines of inquiry were identified and then critically evaluated, (3) promising applied research topics were highlighted in the various lines of inquiry, and (4) these were discussed and prioritized. The summary report will serve as a resource to guide management and decision-making throughout the period of the subject MNA/EPR Alternative Project. To support and more fully document the information presented in the summary report, we are publishing a series of supplemental documents that present the full texts from the technical analyses within the various lines of inquiry (see listing). The following report - documenting our evaluation of the state of the science of the characterization and monitoring process and tools-- is one of those supplemental documents.

Vangelas, K; Tom Early, T; Michael Heitkamp, M; Brian02 Looney, B; David Major, D; Brian Riha, B; Jody Waugh, J; Gary Wein, G

2004-06-18T23:59:59.000Z

411

Engineering-support services for the DOE/GRI coal-gasification research program. Quarterly technical progress report, October-December 1980  

SciTech Connect (OSTI)

Kellogg activities included continued monitoring of test operations at BI-GAS, Westinghouse, Exxon and IGT (for peak gasification). Pilot plant/PDU test runs which were monitored and reported included: BI-GAS tests G-14, G-14A, G-15 and G-15A; Westinghouse PDU tests TP-027-5 and TP-031-1 and CFSF tests TP-M001-1, 2, 3 and 4; Exxon run periods No. 23 and No. 24; and IGT single-stage peat gasification tests BF-1 through BF-6. Draft reports were submitted regarding Hygas data base evaluation, gasifier vessel design and scaleup risks of the Westinghouse oxygen-blown gasifier. Evaluation of the Hygas data base continued, and a similar study of the Peatgas PDU data base was initiated. Work was begun on preparation of a descriptive brochure for the DOE/GRI joint program. Kellogg personnel participated in investigations of welding materials with the MPC. Significant progress was made in the technical/economic assessments of Westinghouse, Exxon and Peatgas and in the technical/economic comparison of Westinghouse and U-gas, with technical definitions being essentially finished and cost estimation begun. Technical definition and preliminary capital cost estimates were completed for the peat harvesting/dewatering study. Work continued in the study of carbonyl formation. Following reviews by the developers, Kellogg began finalization of the report on screening evaluations of Westinghouse, Exxon and Rockwell. Work on the safety assurance study continued, with the commencement of safety audit visits.

Bostwick, L.E.; Brancheau, R.J.; Chen, R.G.

1980-01-01T23:59:59.000Z

412

324 Building safety basis criteria document  

SciTech Connect (OSTI)

The Safety Basis Criteria document describes the proposed format, content, and schedule for the preparation of an updated Safety Analysis Report (SAR) and Operational Safety Requirements document (OSR) for the 324 Building. These updated safety authorization basis documents are intended to cover stabilization and deactivation activities that will prepare the facility for turnover to the Environmental Restoration Contractor for final decommissioning. The purpose of this document is to establish the specific set of criteria needed for technical upgrades to the 324 Facility Safety Authorization Basis, as required by Project Hanford Procedure HNF-PRO-705, Safety Basis Planning, Documentation, Review, and Approval.

STEFFEN, J.M.

1999-06-02T23:59:59.000Z

413

Effects of dispersion and support on adsorption, catalytic and electronic properties of cobalt/alumina CO hydrogenation catalysts: (Technical progress report)  

SciTech Connect (OSTI)

The continued investigation of dispersion and metal-support interactions and their effects upon the adsorption, activity/selectivity, and electronic properties of the metal in cobalt/alumina (and to a lesser extent on iron/alumina) catalysts is proposed. The objectives of this research are to determine the effects of surface structure and metal dispersion on the adsorption and catalytic properties of cobalt, and determine the effects of metal-support interactions, i.e., effects of decorating support species on metal crystallites and of direct electronic interactions between metal clusters and the support, on the adsoprtion, catalytic and electronic properties of cobalt supported on alumina.

Bartholomew, C.H. Jr.

1986-12-22T23:59:59.000Z

414

Hanford Waste Vitrification Plant technical manual  

SciTech Connect (OSTI)

A key element of the Hanford waste management strategy is the construction of a new facility, the Hanford Waste Vitrification Plant (HWVP), to vitrify existing and future liquid high-level waste produced by defense activities at the Hanford Site. The HWVP mission is to vitrify pretreated waste in borosilicate glass, cast the glass into stainless steel canisters, and store the canisters at the Hanford Site until they are shipped to a federal geological repository. The HWVP Technical Manual (Manual) documents the technical bases of the current HWVP process and provides a physical description of the related equipment and the plant. The immediate purpose of the document is to provide the technical bases for preparation of project baseline documents that will be used to direct the Title 1 and Title 2 design by the A/E, Fluor. The content of the Manual is organized in the following manner. Chapter 1.0 contains the background and context within which the HWVP was designed. Chapter 2.0 describes the site, plant, equipment and supporting services and provides the context for application of the process information in the Manual. Chapter 3.0 provides plant feed and product requirements, which are primary process bases for plant operation. Chapter 4.0 summarizes the technology for each plant process. Chapter 5.0 describes the engineering principles for designing major types of HWVP equipment. Chapter 6.0 describes the general safety aspects of the plant and process to assist in safe and prudent facility operation. Chapter 7.0 includes a description of the waste form qualification program and data. Chapter 8.0 indicates the current status of quality assurance requirements for the Manual. The Appendices provide data that are too extensive to be placed in the main text, such as extensive tables and sets of figures. The Manual is a revision of the 1987 version.

Larson, D.E. [ed.; Watrous, R.A.; Kruger, O.L. [and others

1996-03-01T23:59:59.000Z

415

Development of asphalts and pavements using recycled tire rubber. Phase 1: technical feasibility. Final report  

SciTech Connect (OSTI)

This report documents the technical progress made on the development of asphalts and pavements using recycled tire rubber.

Bullin, J.A.; Davison, R.R.; Glover, C.J. [and others

1998-01-01T23:59:59.000Z

416

International Workshop on Deposition of Solids in Geothermal Systems, Technical Papers  

SciTech Connect (OSTI)

This document is a compilation of many technical papers that contain little or no cost data. [DJE-2005

None

1988-08-16T23:59:59.000Z

417

Documenting Spreadsheets  

E-Print Network [OSTI]

This paper discusses spreadsheets documentation and new means to achieve this end by using Excel's built-in "Comment" function. By structuring comments, they can be used as an essential tool to fully explain spreadsheet. This will greatly facilitate spreadsheet change control, risk management and auditing. It will fill a crucial gap in corporate governance by adding essential information that can be managed in order to satisfy internal controls and accountability standards.

Payette, Raymond

2008-01-01T23:59:59.000Z

418

Document13  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc DocumentationP-Series to UserProduct:Directives Templates The

419

Environmental Documents  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc DocumentationP-Series toESnet4: NetworkingEnvironment Environment

420

Technical Assistance to Developers  

SciTech Connect (OSTI)

This task supports the allowance of technical assistance to fuel-cell component and system developers as directed by the DOE. This task includes testing of novel materials and participation in the further development and validation of single cell test protocols. This task also covers technical assistance to DOE Working Groups, the U.S. Council for Automotive Research (USCAR) and the USCAR/DOE Driving Research and Innovation for Vehicle efficiency and Energy sustainability (U.S. Drive) Fuel Cell Technology Team. Assistance includes technical validation of new fuel cell materials and methods, single cell fuel cell testing to support the development of targets and test protocols, and regular advisory participation in other working groups and reviews. This assistance is made available to PEM fuel cell developers by request and DOE Approval. The objectives are to: (1) Support technically, as directed by DOE, fuel cell component and system developers; (2) Assess fuel cell materials and components and give feedback to developers; (3) Assist the DOE Durability Working Group with the development of various new material durability Testing protocols; and (4) Provide support to the U.S. Council for Automotive Research (USCAR) and the USCAR/DOE Fuel Cell Technology Team. FY2012 specific technical objectives are: (1) Evaluate novel MPL materials; (2) Develop of startup/ shutdown protocol; (3) Test the impact of hydrophobic treatment on graphite bi-polar plates; (4) Perform complete diagnostics on metal bi-polar plates for corrosion; and (5) Participate and lead efforts in the DOE Working Groups.

Rockward, Tommy [Los Alamos National Laboratory; Borup, Rodney L. [Los Alamos National Laboratory; Garzon, Fernando H. [Los Alamos National Laboratory; Mukundan, Rangachary [Los Alamos National Laboratory; Spernjak, Dusan [Los Alamos National Laboratory

2012-07-17T23:59:59.000Z

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Technical Qualification Program Self-Assessment Report- Oak Ridge Office- 2014  

Broader source: Energy.gov [DOE]

This assessment, using criteria referred to in DOE O 426.1, Federal Technical Capability, is designed to evaluate the effectiveness of the implementation of the FTCP and the TQP at ORO. The purpose of this report is to document the results of ORO's self-assessment. The remaining sections of this report include the assessment scope and methodology, the results of the assessment, and supporting information.

422

Review of Used Nuclear Fuel Storage and Transportation Technical...  

Broader source: Energy.gov (indexed) [DOE]

action based on the comparison. Review of Used Nuclear Fuel Storage and Transportation Technical Gap Analysis More Documents & Publications Review of Used Nuclear Fuel...

423

Test Methods Standing Technical Committee Strategic Plan - February...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Strategic Plan - February 2012 Test Methods Standing Technical Committee Strategic Plan - February 2012 This document outlines gaps, needs, and opportunities identified by the...

424

December 2012 Buildings to Grid Integration Technical Meeting...  

Broader source: Energy.gov (indexed) [DOE]

b2gmtngwappendix0113.pdf More Documents & Publications May 2, 2014 Technical Meeting: Reference Guide for a Transaction-Based Building Controls Framework Rooftop Unit Network...

425

Technical Qualification Program Self-Assessment Report - Los...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

and Federal Technical Capability program was conducted to provide Los Alamos Field Office management specific information related to effectiveness of the documentation and...

426

Solar Technical Assistance Team (STAT) Summer Webinar Series: Webinar 3  

Broader source: Energy.gov [DOE]

This document details the Solar Technical Assistance Team (STAT) Summer Webinar Series: Webinar 3: Solar Technology Options and Resource Assessment Question & Answer Session on August 15, 2012.

427

Onboard Hydrogen/Helium Sensors in Support of the Global Technical Regulation: An Assessment of Performance in Fuel Cell Electric Vehicle Crash Tests  

SciTech Connect (OSTI)

Automobile manufacturers in North America, Europe, and Asia project a 2015 release of commercial hydrogen fuel cell powered light-duty road vehicles. These vehicles will be for general consumer applications, albeit initially in select markets but with much broader market penetration expected by 2025. To assure international harmony, North American, European, and Asian regulatory representatives are striving to base respective national regulations on an international safety standard, the Global Technical Regulation (GTR), Hydrogen Fueled Vehicle, which is part of an international agreement pertaining to wheeled vehicles and equipment for wheeled vehicles.

Post, M. B.; Burgess, R.; Rivkin, C.; Buttner, W.; O'Malley, K.; Ruiz, A.

2012-09-01T23:59:59.000Z

428

Technical Guidance  

Broader source: Energy.gov [DOE]

The Office of Technical Guidance, within the Office of Health, Safety and Security develops and issues Government-wide and Department-wide technical guidance to ensure that classified nuclear...

429

Document Information  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed Newcatalyst phasesDataTranslocationDiurnal Cycle ofDo New55 FederalChapter5 Document

430

Document Delivery  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc DocumentationP-Series to UserProduct:Directives Templates The OfficeDitchDivya401

431

Reference Documents  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 -the Mid-Infrared at 278, 298,NIST 800-53 NationalTreatment.Reference-Documents Sign

432

Reference Documents  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 -the Mid-Infrared at 278, 298,NIST 800-53 NationalTreatment.Reference-Documents

433

Engineering-support services for the DOE/GRI coal-gasification research program. Quarterly technical progress report, July-September 1981  

SciTech Connect (OSTI)

During July-September 1981 Kellogg continued to actively monitor operations at BI-GAS, Westinghouse and IGT (for peat gasification). Pilot plant/PDU tests which were monitored and reported included BI-GAS Tests G-17D, G-17E, and G-17F; Westinghouse PDU test runs TP-0282 and TP-028-3 and CFSF Tests TP-M002-2 and TP-M006-1; Peatgas pilot plant Tests number 2 and number 3; and single-stage peat gasification PDU Test BF-21. Work on several task orders was completed with the issue of final reports on technical/economic assessments of Exxon, Westinghouse and Peatgas, the technical/economic comparison of Westinghouse and U-Gas, safety audits, safety assurance, peat harvesting and dewatering, gasifier vessel design and carbonyl formation. Kellogg continued its efforts toward completion of the descriptive brochure for the DOE/GRI Joint program and of the reports on the Hygas and Peatgas data bases. A new subtask, to evaluate the data base for single-stage peat gasification, was undertaken, and Kellogg participated in reviews of the Hygas final report. Normal MPC activities continued.

Bostwick, L.E.; Ethridge, T.R.; Gilwood, W.C.; Glasgow, P.E.; Hubbard, D.A.; Shah, K.V.; Singer, D.L.; Smith, M.R.; Ward, W.E.

1981-01-01T23:59:59.000Z

434

Engineering-support services for the DOE/GRI coal-gasification research program. Quarterly technical progress report, April-June 1981  

SciTech Connect (OSTI)

Kellog activities during April to June 1981 included continued monitoring of activities at Bi-Gas, Westinghouse, Exxon and IGT (for peat gasification). Pilot plant/PDU tests which were monitored and reported include Bi-Gas tests G-16B, G-17, G-17A, G-17B, and G-17C; Westinghouse PDU test runs TP-029-1/030-1, TP-030-2 and TP-028-1 and CFSF tests TP-M002-1 and TP-M002-2; Exxon run period number 28; Peatgas pilot plant Test RF-1 and gasification Test number 1; and IGT single-stage peat gasification PDU Tests BF-13 through BF-20. Significant milestones were reached with the issue of draft reports for several tasks, including carbonyl formation, peat harvesting/dewatering, technical/economic assessments of Exxon, Westinghouse and PeatGas, technical/economic comparison of Westinghouse and U-Gas, gasifier design, safety audits, Hygas data base evaluation and the safety assurance study. In addition, final reports were issued for the Westinghouse oxygen blown gasifier risk analysis and for the PDU screening evaluations of Exxon, Westinghouse and Rockwell. Work on the Peatgas PDU data base evaluation continued, and a review of the Hygas final report was begun.

Bernard, D.M.; Bostwick, L.E.; Ethridge, T.R.; Gilwood, W.C.; Hubbard, D.A.; Montgomery, R.L.; Senules, E.A.; Singer, D.L.; Smith, M.R.; Ward, W.E.

1981-01-01T23:59:59.000Z

435

Engineering-support services for the DOE/GRI Coal-Gasification Research Program. Quarterly technical progress report, July-September 1980  

SciTech Connect (OSTI)

Kellogg activities included contained monitoring of test operations at the Hygas, BI-GAS, Westinghoue, Exxon and Bell plant sites. Peat gasification laboratory tests were also monitored; Rockwell testing ended during June. Pilot Plant/PDU test runs monitored and reported were: Hygas Test 87 (the last of the pilot plant series), BI-GAS Tests G-13 and G-14, Westinghouse test runs TP-027, TP-027-4 and TP-027-5, Exxon test periods 19 through 21 and Bell Tests 2174 through 3195. Kellogg continued its work on the Hygas data base evaluation and began an evaluation of the scaleup risks of the Westinghouse oxygen-blown gasifier. Work under new task orders was initiated. The topics included are: Technical/Economic Assessments of Westinghouse, Exxon and Peatgas, Gasifier Vessel Design, Technical/Economic Comparisons of Westinghouse and U-Gas, Peat Harvesting and Dewatering, and Carbonyl Formation in Coal Gasification processes. Economics are essentially complete for the Screening Evaluations of Westinghouse, Exxon and Rockwell and report preparation has begun. Work on the Pilot/Plant PDU Safety Evaluation Task continued.

Bostwick, L.E.; Brancheau, R.J.; Castiglioni, B.P.

1982-01-01T23:59:59.000Z

436

Tokamak Physics EXperiment (TPX): Toroidal field magnet design, development and manufacture. SDRL 32, Coil assembly documentation. Volume 5  

SciTech Connect (OSTI)

This document is intended to address the contract requirement for providing coil assembly documentation, as required in the applicable Statement of Work: `Provide preliminary procedures and preliminary design and supporting analysis of the equipment, fixtures, and hardware required to integrate and align the impregnated coil assemblies with the coil cases and intercoil structure. Each of the three major processes associated with the coil case and intercoil structure (ICS), TF Case Fabrication, Coil Preparation for Case Assembly are examined in detail. The specific requirements, processes, equipment, and technical concerns for each of these assembly processes is presented.

Weber, C.M. [Babcock and Wilcox Co., Lynchburg, VA (United States)

1995-08-18T23:59:59.000Z

437

Work Authorization Document NSTX Upgrade Project  

E-Print Network [OSTI]

Work Authorization Document NSTX Upgrade Project Control Account #: 7900 Title: WBS 1.7.3 Title Functional Manager L. Dudek Approvals Signature Date NSTX-U Project Manager R. Strykowsky 4- WBS Dictionary procedures and documents to support the integrated tests, and to support performance of the pre

Princeton Plasma Physics Laboratory

438

Mined Geologic Disposal System Requirements Document. Revision 1  

SciTech Connect (OSTI)

This Mined Geologic Disposal System Requirements Document (MGDS-RD) describes the functions to be performed by, and the requirements for, a Mined Geologic Disposal System (MGDS) for the permanent disposal of spent nuclear fuel (SNF) (including SNF loaded in multi-purpose canisters (MPCs)) and commercial and defense high-level radioactive waste (HLW) in support of the Civilian Radioactive Waste Management System (CRWMS). The purpose of the MGDS-RD is to define the program-level requirements for the design of the Repository, the Exploratory Studies Facility (ESF), and Surface Based Testing Facilities (SBTF). These requirements include design, operation, and decommissioning requirements to the extent they impact on the physical development of the MGDS. The document also presents an overall description of the MGDS, its functions (derived using the functional analysis documented by the Physical System Requirements (PSR) documents as a starting point), its segments as described in Section 3.1.3, and the requirements allocated to the segments. In addition, the program-level interfaces of the MGDS are identified. As such, the MGDS-RD provides the technical baseline for the design of the MGDS.

Not Available

1994-03-01T23:59:59.000Z

439

Yucca Mountain Site Characterization Project: Technical Data Catalog quarterly supplement  

SciTech Connect (OSTI)

The March 21, 1993, Department of Energy (DOE)/Nuclear Regulatory Commission (NRC) Site-Specific Procedural Agreement for Geologic Repository Site Investigation and Characterization Program requires the DOE to develop and maintain a catalog of data which will be updated and provided to the NRC at least quarterly. This catalog is to include a description of the data; the time (date), place, and method of acquisition; and where it may be examined. The Yucca Mountain Site Characterization Project (YMP) Technical Data Catalog is published and distributed in accordance with the requirements of the Site-Specific Agreement. The YMP Technical Data Catalog is a report based on reference information contained in the YMP Automated Technical Data Tracking System (ATDT). The reference information is provided by Participants for data acquired or developed in support of the YMP. The Technical Data Catalog is updated quarterly and published in the month following the end of each quarter. A complete revision to the Catalog is published at the end of each fiscal year. Supplements to the end-of-year edition are published each quarter. These supplements provide information related to new data items not included in previous quarterly updates and data items affected by changes to previously published reference information. The Technical Data Catalog, dated September 30, 1993, should be retained as the baseline document for the supplements until the end-of-year revision is published and distributed in October 1994.

NONE

1994-03-31T23:59:59.000Z

440

Yucca Mountain Site Characterization Project technical data catalog quarterly supplement  

SciTech Connect (OSTI)

The Department of Energy (DOE)/Nuclear Regulatory Commission (NRC) Site-Specific Procedural Agreement for Geologic Repository Site Investigation and Characterization Program requires the DOE to develop and maintain a catalog of data which will be updated and provided to the NRC at least quarterly. This catalog is to include a description of the data; the time (date), place, and method of acquisition; and where the data may be examined. The Yucca Mountain Site Characterization Project (YMP) Technical Data Catalog is published and distributed in accordance with t requirements of the Site-Specific Agreement. The YMP Technical Data Catalog is a report based on reference information contained in the YMP Automated Technical Data Tracking System (ATDT). The reference information is provided by Participants for data acquired or developed in support of the YMP. The Technical Data Catalog is updated quarterly and distributed in the month following the end of each quarter. A complete revision to the catalog is published at the end of each fiscal year. Supplements to the end-of-year edition are published each quarter. These supplements provide information related to new data items not included in previous quarterly updates and data items affected by changes to@ previously published reference information. The Technical Data Catalog, dated September 30, 1994, should be retained as the baseline document for the supplements until the end-of-year revision is published and distributed in October 1995.

NONE

1995-03-31T23:59:59.000Z

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

SAE Standards Support  

SciTech Connect (OSTI)

This report summarizes PNNL activities in FY 2012 in support of the following two vehicle communication standards activities: • Technical support to SAE, ANSI and NIST technical working groups. PNNL actively contributed to the use case development, harmonization, and evaluation of the SAE standards activities for vehicle to grid communication • Tested and validated a set of potential technologies for meeting SAE communication requirements and provided recommendations for technology choices.

Gowri, Krishnan

2012-11-01T23:59:59.000Z

442

DOE technical standards list. Department of Energy standards index  

SciTech Connect (OSTI)

This document was prepared for use by personnel involved in the selection and use of DOE technical standards and other Government and non-Government standards. This TSL provides listing of current DOE technical standards, non-Government standards that have been adopted by DOE, other Government documents in which DOE has a recorded interest, and canceled DOE technical standards. Information on new DOE technical standards projects, technical standards released for coordination, recently published DOE technical standards, and activities of non-Government standards bodies that may be of interest to DOE is published monthly in Standards Actions.

NONE

1995-08-01T23:59:59.000Z

443

American Recovery and Reinvestment Act (ARRA) FEMP Technical Assistance Federal Aviation Administration – Project 209 Control Tower and Support Building, Reno, Nevada  

SciTech Connect (OSTI)

Pacific Northwest National Laboratory (PNNL) and Redhorse Corporation (Redhorse) conducted an energy audit on the Federal Aviation Administration (FAA) control tower and base building in Reno, Nevada. This report presents the findings of the energy audit team that evaluated construction documents and operating specifications (at the 100% level) and completed a site visit. The focus of the review was to identify measures that could be incorporated into the final design and operating specifications that would result in additional energy savings for the FAA that would not have otherwise occurred.

Arends, J.; Sandusky, William F.

2010-06-30T23:59:59.000Z

444

Technical information report: Plasma melter operation, reliability, and maintenance analysis  

SciTech Connect (OSTI)

This document provides a technical report of operability, reliability, and maintenance of a plasma melter for low-level waste vitrification, in support of the Hanford Tank Waste Remediation System (TWRS) Low-Level Waste (LLW) Vitrification Program. A process description is provided that minimizes maintenance and downtime and includes material and energy balances, equipment sizes and arrangement, startup/operation/maintence/shutdown cycle descriptions, and basis for scale-up to a 200 metric ton/day production facility. Operational requirements are provided including utilities, feeds, labor, and maintenance. Equipment reliability estimates and maintenance requirements are provided which includes a list of failure modes, responses, and consequences.

Hendrickson, D.W. [ed.

1995-03-14T23:59:59.000Z

445

Comparisons of ANSI standards cited in the NRC standard review plan, NUREG-0800 and related documents  

SciTech Connect (OSTI)

This report provides the results of comparisons of the cited and latest versions of ANSI standards cited in the NRC Standard Review Plan for the Review of Safety Analysis Reports for Nuclear Power Plants (NUREG 0800) and related documents. The comparisons were performed by Battelle Pacific Northwest Laboratories in support of the NRC`s Standard Review Plan Update and Development Program. Significant changes to the standards, from the cited version to the latest version, are described and discussed in a tabular format for each standard. Recommendations for updating each citation in the Standard Review Plan are presented. Technical considerations and suggested changes are included for related regulatory documents (i.e., Regulatory Guides and the Code of Federal Regulations) citing the standard. The results and recommendations presented in this document have not been subjected to NRC staff review.

Ankrum, A.R.; Bohlander, K.L.; Gilbert, E.R.; Pawlowski, R.A.; Spiesman, J.B. [Pacific Northwest Lab., Richland, WA (United States)

1995-11-01T23:59:59.000Z

446

Comparisons of ASTM standards cited in the NRC standard review plan, NUREG-0800 and related documents  

SciTech Connect (OSTI)

This report provides the results of comparisons of the cited and latest versions of ASTM standards cited in the NRC Standard Review Plan for the Review of Safety Analysis Reports for Nuclear Power Plants (NUREG 0800) and related documents. The comparisons were performed by Battelle Pacific Northwest Laboratories in support of the NRC`s Standard Review Plan Update and Development Program. Significant changes to the standards, from the cited version to the latest version, are described and discussed in a tabular format for each standard. Recommendations for updating each citation in the Standard Review Plan are presented. Technical considerations and suggested changes are included for related regulatory documents (i.e., Regulatory Guides and the Code of Federal Regulations) citing the standard. The results and recommendations presented in this document have not been subjected to NRC staff review.

Ankrum, A.R.; Bohlander, K.L.; Gilbert, E.R.; Pawlowski, R.A.; Spiesman, J.B.

1995-10-01T23:59:59.000Z

447

Enforcement Documents  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review: TopEnergyIDIQBusinessinSupporting JobsClean EnergyAcrossinput

448

DOE technical standards list: Department of Energy standards index  

SciTech Connect (OSTI)

This Department of Energy (DOE) technical standards list (TSL) has been prepared by the Office of Nuclear Safety Policy and Standards (EH-31) on the basis of currently available technical information. Periodic updates of this TSL will be issued as additional information is received on standardization documents being issued, adopted, or canceled by DOE. This document was prepared for use by personnel involved in the selection and use of DOE technical standards and other Government and non-Government standards. This TSL provides listings of current DOE technical standards, non-Government standards that have been adopted by DOE, other standards-related documents in which DOE has a recorded interest, and canceled DOE technical standards. Information on new DOE technical standards projects, technical standards released for coordination, recently published DOE technical standards, and activities of non-Government standards bodies that may be of interest to DOE is published monthly in Standards Actions.

NONE

1999-05-01T23:59:59.000Z

449

94-1 Research and development project lead laboratory support. Status report, July 1, 1996--September 30, 1996  

SciTech Connect (OSTI)

This document reports status and technical progress for Los Alamos 94-1 Research and Development projects. Updated schedule charts are shown in the appendix. This is the fourth status report published for Los Alamos National Laboratory 94-1 Research and Development Project Support. The Department of Energy Office of Environmental Management (DOE/EM) funds these projects in order to support the storage or disposal of legacy plutonium and plutonium-bearing materials resulting from weapons production throughout the DOE complex. This document also serves as an end-for-year review of projects and positions the program for FY97.

Rink, N. [comp.

1997-03-01T23:59:59.000Z

450

Tank waste remediation system functions and requirements document  

SciTech Connect (OSTI)

This is the Tank Waste Remediation System (TWRS) Functions and Requirements Document derived from the TWRS Technical Baseline. The document consists of several text sections that provide the purpose, scope, background information, and an explanation of how this document assists the application of Systems Engineering to the TWRS. The primary functions identified in the TWRS Functions and Requirements Document are identified in Figure 4.1 (Section 4.0) Currently, this document is part of the overall effort to develop the TWRS Functional Requirements Baseline, and contains the functions and requirements needed to properly define the top three TWRS function levels. TWRS Technical Baseline information (RDD-100 database) included in the appendices of the attached document contain the TWRS functions, requirements, and architecture necessary to define the TWRS Functional Requirements Baseline. Document organization and user directions are provided in the introductory text. This document will continue to be modified during the TWRS life-cycle.

Carpenter, K.E

1996-10-03T23:59:59.000Z

451

Enforcement Documents  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review: TopEnergyIDIQBusinessinSupporting JobsClean EnergyAcrossinput246 Enforcement

452

Enron Documents  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review: TopEnergyIDIQBusinessinSupportingEnergy2 ENRON CORP Kenneth L. Lay P. o. a

453

Enron Documents  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review: TopEnergyIDIQBusinessinSupportingEnergy2 ENRON CORP Kenneth L. Lay P. o. af

454

Enron Documents  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review: TopEnergyIDIQBusinessinSupportingEnergy2 ENRON CORP Kenneth L. Lay P. o.

455

Enron Documents  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review: TopEnergyIDIQBusinessinSupportingEnergy2 ENRON CORP Kenneth L. Lay P. o.8

456

Enron Documents  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review: TopEnergyIDIQBusinessinSupportingEnergy2 ENRON CORP Kenneth L. Lay P.

457

Enron Documents  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review: TopEnergyIDIQBusinessinSupportingEnergy2 ENRON CORP Kenneth L. Lay P.0

458

Enron Documents  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review: TopEnergyIDIQBusinessinSupportingEnergy2 ENRON CORP Kenneth L. Lay P.02001

459

Enron Documents  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review: TopEnergyIDIQBusinessinSupportingEnergy2 ENRON CORP Kenneth L. Lay P.020012

460

Final technical report for the Award DE-FG02-08ER64574, with list of 30 refereed journal articles that acknowledge support from this award.  

SciTech Connect (OSTI)

In this project, we focused on applications of the new warm-rain and ice microphysics schemes to simulate various cloud systems. The overall goal was either to evaluate and improve specific aspects of the schemes (through comparisons with ARM/ASR observations) or to understand the coupling between aerosols, cloud microphysics and cloud dynamics in variety of situations. These studies are relevant to the indirect impact of atmospheric aerosols on climate. Below we report on selected key aspects of the research and then list all peer-reviewed papers that acknowledge support from this grant. Overall, studies partially supported by this grant resulted in 30 peer-reviewed publications (listed below), several dozens of conference presentations (including posters and oral presentations at the ASR Science Team Meetings), and two PhD dissertations. More detailed summaries of our accomplishments are included in yearly reports. Here we summarize only major efforts.

Wojciech W. Grabowski

2012-04-02T23:59:59.000Z

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Evaluation of using cyclocranes to support drilling and production of oil and gas in wetland areas. Fourth quarterly technical progress report, Second quarter, 1993  

SciTech Connect (OSTI)

The planned program falls under wetlands area research related to drilling, production, and transportation of oil and gas resources. Specifically the planned program addresses an evaluation of using cyclocraft to transport drill rigs, mud, pipes and other materials and equipment in a cost effective and environmentally safe manner to support oil and gas drilling and production operations in wetland areas. The cyclocraft is a proven hybrid aircraft that utilizes aerostatic and aerodynamic lift. This type of aircraft has considerable payload capacity, VTOL capability, high controllability, low operating cost, low downwash and high safety. The benefits of using a cyclocraft to transport drill rigs and materials over environmentally-sensitive surfaces would be significant. The cyclocraft has considerable cost and operational advantages over the helicopter. The major activity during the second quarter of 1993 was focussed on completion of Task 4, Preliminary Design. The selected design has been designated H.1 Cyclocraft by MRC. Also during the report period, Task 6, Ground Support, was completed and a report containing the results was submitted to DOE. This task addressed the complete H.1 Cyclocraft system, i.e. it included the need personnel, facilities and equipment to support cyclocraft operations in wetland areas.

Eggington, W.J.

1993-09-01T23:59:59.000Z

462

XML Document XML Document Types and Validation  

E-Print Network [OSTI]

XML Document Types and Validation IIM-I340 Objectives XML Document Types and Validation IIM-I340 April, 2010 #12;XML Document Types and Validation IIM-I340 Objectives Learning Objectives Understand: The need for validation Two ways to specify validity: Document Type Definitions (DTDs) XML Schemas #12;XML

Weber, Gregory D.

463

Engineering support services for the DOE/GRI coal-gasification research program. Quarterly technical progress report, April-June 1980  

SciTech Connect (OSTI)

Kellogg activities included continued monitoring of test operations at the Hygas, BI-GAS, Westinghouse, Exxon, Rockwell and Bell plant sites, and of peat gasification laboratory activities. Pilot plant/PDU test runs monitored and reported were: Hygas Tests 85 and 86; BI-GAS Tests G-11C, 11D, 11E, 11F, G-12 and G-12A; Westinghouse test runs TP-023-4, TP-027-1, TP-027-2 and TP-027-3; Exxon test periods 13 through 17; and Rockwell Tests 318-063 through 318-073. Kellogg made significant progress toward completion of the Operating Plan Requirements for the individual developers, and began an evaluation of the Hygas data base. The final report on Westinghouse Risk Analysis were issued. Progress was made in completing the reports of the screening evaluations of Exxon, Rockwell and Westinghouse. The safety assurance study continued, as did normal participation in MPC activities. New task orders for technical/economic studies were submitted for review and approval.

Bostwick, L.E.; Brancheau, R.J.; Chen, R.G.

1980-01-01T23:59:59.000Z

464

The Independent Technical Analysis Process  

SciTech Connect (OSTI)

The Bonneville Power Administration (BPA) contracted with the Pacific Northwest National Laboratory (PNNL) to provide technical analytical support for system-wide fish passage information (BPA Project No. 2006-010-00). The goal of this project was to produce rigorous technical analysis products using independent analysts and anonymous peer reviewers. In the past, regional parties have interacted with a single entity, the Fish Passage Center to access the data, analyses, and coordination related to fish passage. This project provided an independent technical source for non-routine fish passage analyses while allowing routine support functions to be performed by other well-qualified entities.

Duberstein, Corey A.; Ham, Kenneth D.; Dauble, Dennis D.; Johnson, Gary E.

2007-04-13T23:59:59.000Z

465

Technical Report  

E-Print Network [OSTI]

Dec 12, 2013 ... Technical Report Series: DCC-2013-13. Departamento de Ciência de Computadores. Faculdade de Ciências da Universidade do Porto.

Filipe Brandao

2013-12-12T23:59:59.000Z

466

Omega documentation  

SciTech Connect (OSTI)

OMEGA is a CRAY I computer program that controls nine codes used by LLNL Physical Data Group for: 1) updating the libraries of evaluated data maintained by the group (UPDATE); 2) calculating average values of energy deposited in secondary particles and residual nuclei (ENDEP); 3) checking the libraries for internal consistency, especially for energy conservation (GAMCHK); 4) producing listings, indexes and plots of the library data (UTILITY); 5) producing calculational constants such as group averaged cross sections and transfer matrices for diffusion and Sn transport codes (CLYDE); 6) producing and updating standard files of the calculational constants used by LLNL Sn and diffusion transport codes (NDFL); 7) producing calculational constants for Monte Carlo transport codes that use group-averaged cross sections and continuous energy for particles (CTART); 8) producing and updating standard files used by the LLNL Monte Carlo transport codes (TRTL); and 9) producing standard files used by the LANL pointwise Monte Carlo transport code MCNP (MCPOINT). The first four of these functions and codes deal with the libraries of evaluated data and the last five with various aspects of producing calculational constants for use by transport codes. In 1970 a series, called PD memos, of internal and informal memoranda was begun. These were intended to be circulated among the group for comment and then to provide documentation for later reference whenever questions arose about the subject matter of the memos. They have served this purpose and now will be drawn upon as source material for this more comprehensive report that deals with most of the matters covered in those memos.

Howerton, R.J.; Dye, R.E.; Giles, P.C.; Kimlinger, J.R.; Perkins, S.T.; Plechaty, E.F.

1983-08-01T23:59:59.000Z

467

Strategies for International Cooperation in Support of Energy Development in Pacific Island Nations  

SciTech Connect (OSTI)

The U.S. Department of Energy's National Renewable Energy Laboratory (NREL) has been partnering with island communities around the world to address the technical, policy, social, and economic hurdles to deploying energy efficiency and renewable energy technologies (RETs) on small, islanded systems. The lessons learned from these partnerships are briefly summarized in this document with the goal of supporting the International Renewable Energy Agency (IRENA) in the development of specific near-term and longer-term strategies for island RET deployment.

Miller, M.; Voss, P.; Warren, A.; Baring-Gould, I.; Conrad, M.

2012-05-01T23:59:59.000Z

468

Technical and economic assessment of the IGT peat-gasification process. Engineering support services for the DOE/GRI Coal Gasification Research Program  

SciTech Connect (OSTI)

Kellogg has completed a moderately detailed design and cost estimate of a 250 billion Btu/Day grass-roots SNG plant using the Peatgas process. Results indicate that the cost of SNG would be $4.40/MM Btu, using a cost of $1.50/MM Btu for peat feedstock at 50% moisture. The SNG cost is reasonably competitive with that currently estimated for SNG from coal, and Kellogg would anticipate that capital cost reductions, via design optimization, could reduce the NSG cost to a level which is quite competitive. The cost of peat feedstock is a critical area of concern in evaluating economics of the Peatgas process. The value chosen for the base-case economics ($1.50/MM Btu) is in the higher portion of the price range considered typical by most investigators; the price of $1.50/MM Btu was chosen arbitrarily to represent a 50% increase over the cost of coal ($1.00/MM Btu) used by Kellogg in parallel studies, to reflect higher costs for land use and reclamation and for harvesting and dewatering of peat. In a study concurrent with that reported here, Kellogg found that one method of wet harvesting and mechanical/thermal dewatering yields a peat (50% moisture) cost which is unfavorably high and was therefore rejected for use as a base-case cost since much cheaper feedstock is apparently available by other harvesting/dewatering methods. The base-case cost of SNG is moderate somewhat by the values placed on the benzene and oil coproducts (i.e., $1.10 and $0.75 per gallon, respectively). The total of such credits amounts to about 39% of the gross operating cost; a reduction in value of the coproducts would adversely affect the cost of SNG. Certain technical factors are discussed: materials handling problems, high reactivity, low sulfur content, and limited gasification data.

Bostwick, L.E.; Hubbard, D.A.; Laramore, R.W.; Senules, E.A.; Shah, K.V.

1981-04-01T23:59:59.000Z

469

Evaluation of using cyclocranes to support drilling & production of oil & gas in wetland areas. Sixth quarterly technical progress report, incorporating milestone schedule/status, October 1993--December 1993  

SciTech Connect (OSTI)

This report is a progress report on a planned program falling under wetlands area research related to drilling, production, and transportation of oil and gas resources. Specifically the planned program addresses an evaluation of using cyclocraft to transport drill rigs, mud, pipes and other materials and equipment in a cost effective and environmentally safe manner to support oil and gas drilling and production operations in wetland areas. During this period, task 5, subscale tests, and task 7, environmental impacts, were completed. Work was continued on task 10, technology transfer, and the preparation of the final report as part of task 11.

Eggington, W.J.

1994-04-01T23:59:59.000Z

470

Evaluation of using cyclocranes to support drilling and production of oil and gas in wetland areas. Fifth quarterly technical progress report, Third quarter, 1993  

SciTech Connect (OSTI)

The planned program falls under wetlands area research related to drilling, production, and transportation of oil and gas resources. Specifically the planned program addresses an evaluation of using cyclocraft to transport drill rigs, mud, pipes and other materials and equipment in a cost effective and environmentally safe manner to support oil and gas drilling and production operations in wetland areas. The cyclocraft is a proven hybrid aircraft that utilizes aerostatic and aerodynamic lift. This type of aircraft has considerable payload capacity, VTOL capability, high controllability, low operating cost, low downwash and high safety. The benefits of using a cyclocraft to transport drill rigs and materials over environmentally-sensitive surfaces would be significant. The cyclocraft has considerable cost and operational advantages over the helicopter. In 1992, Task 1, Environmental Considerations, and Task 2, Transport Requirements, were completed. In the first two quarters of 1993, Task 3, Parametric Analysis, Task 4, Preliminary Design, and Task 6, Ground Support, were completed. Individual reports containing results obtained from each of these tasks were submitted to DOE. In addition, through June 30, 1993, a Subscale Test Plan was prepared under Task 5, Subscale Tests, and work was initiated on Task 7, Environmental Impacts, Task 8, Development Plan, Task 9, Operating Costs, and Task 10, Technology Transfer.

Eggington, W.J.

1993-12-31T23:59:59.000Z

471

Waste management project technical baseline description  

SciTech Connect (OSTI)

A systems engineering approach has been taken to describe the technical baseline under which the Waste Management Project is currently operating. The document contains a mission analysis, function analysis, requirement analysis, interface definitions, alternative analysis, system definition, documentation requirements, implementation definitions, and discussion of uncertainties facing the Project.

Sederburg, J.P.

1997-08-13T23:59:59.000Z

472

Solid Waste Program technical baseline description  

SciTech Connect (OSTI)

The system engineering approach has been taken to describe the technical baseline under which the Solid Waste Program is currently operating. The document contains a mission analysis, function analysis, system definition, documentation requirements, facility and project bases, and uncertainties facing the program.

Carlson, A.B.

1994-07-01T23:59:59.000Z

473

Using MATLAB The Language of Technical Computing  

E-Print Network [OSTI]

Using MATLAB® Graphics Version 7 MATLAB ® The Language of Technical Computing #12;How to Contact The MathWorks: www.mathworks.com Web comp.soft-sys.matlab Newsgroup support@mathworks.com Technical supportWorks Web site. Using MATLAB Graphics © COPYRIGHT 1984 - 2004 by The MathWorks, Inc. The software described

deYoung, Brad

474

Sustainable energy for all. Technical report of task force 1 in support of the objective to achieve universal access to modern energy services by 2030  

SciTech Connect (OSTI)

The UN Secretary General established the Sustainable Energy for All initiative in order to guide and support efforts to achieve universal access to modern energy, rapidly increase energy efficiency, and expand the use of renewable energies. Task forces were formed involving prominent energy leaders and experts from business, government, academia and civil society worldwide. The goal of the Task Forces is to inform the implementation of the initiative by identifying challenges and opportunities for achieving its objectives. This report contains the findings of Task Force One which is dedicated to the objective of achieving universal access to modern energy services by 2030. The report shows that universal energy access can be realized by 2030 with strong, focused actions set within a coordinated framework.

Birol, Fatih [International Energy Agency, Paris (France); Brew-Hammond, Abeeku (University of Science and Technology (Ghana

2012-04-15T23:59:59.000Z

475

Proceedings of the LLNL Technical Women`s Symposium  

SciTech Connect (OSTI)

This report documents events of the LLNL Technical Women`s Symposium. Topics include; future of computer systems, environmental technology, defense and space, Nova Inertial Confinement Fusion Target Physics, technical communication, tools and techniques for biology in the 1990s, automation and robotics, software applications, materials science, atomic vapor laser isotope separation, technical communication, technology transfer, and professional development workshops.

von Holtz, E. [ed.

1993-12-31T23:59:59.000Z

476

DEEP SEA DRILLING PROJECT DATA FILE DOCUMENTS  

E-Print Network [OSTI]

for the program is provided by the following agencies: Department of Energy, Mines and Resources (Canada) Deutsche&M University, as an account of work performed under the international Ocean Drilling Program which is managedDEEP SEA DRILLING PROJECT DATA FILE DOCUMENTS Ocean Drilling Program Texas A&M University Technical

477

RETENTION OF IRB RECORDS AND OTHER DOCUMENTS All IRB files and documents that relate to the protection of human research  

E-Print Network [OSTI]

site. The IRB File Manager and eIRB support staff are available to scan paper documents as needed into Paperhost. The File Manager and all the Board Specialists have access to documents kept on the Paperhost web1 RETENTION OF IRB RECORDS AND OTHER DOCUMENTS 04/18/2011 All IRB files and documents that relate

478

Engineering support services for the DOE/GRI coal-gasification research program. Monthly technical progress report, 22 August - 25 September, 1981  

SciTech Connect (OSTI)

The objective of this contract is to provide engineering support services to the Department of Energy/Gas Research Institute in the high Btu coal gasification research program. The gasification research program is to determine the specific process and/or combination of component processing steps that offer the greatest economic potential for commercial application. During September, Kellogg continued active monitoring of operations at Westinghouse, IGT, Peatgas, and BI-GAS. Efforts relative to Hygas, Rockwell, Exxon and Bell were minimal. Test runs monitored and reported here are BI-GAS tests 17E and 17F, Westinghouse PDU test TP-028-3, and IGT Peatgas test 3. Kellog attended meetings on 1 and 22 September to discuss the review of the Hygas final report. Comments on Kellogg's draft report on the Hygas data base evaluation were received. Kellogg's evaluations of PDU operating data from Westinghouse and Exxon continues. The Kellogg report on Peatgas PDU data base evaluation was issued in draft form. At DOE's request, Kellogg began work on an evaluation of the existing data base (by IGT) for single-stage gasification of peat. Work on the descriptive brochure continued, aimed toward issue of a draft in the near future. Kellogg also provided input regarding Westinghouse test runs to a DOE consultant.

Bostwick, L.E.; Ethridge, T.R.; Starr, D.W.; Hubbard, D.A.; Koneru, P.B.; Smith, M.R.; Ward, W.E.; Wong, E.W.

1982-01-01T23:59:59.000Z

479

Corrective Action Decision Document/Closure Report for Corrective Action Unit 105: Area 2 Yucca Flat Atmospheric Test Sites, Nevada National Security Site, Nevada, Revision 1  

SciTech Connect (OSTI)

The purpose of this Corrective Action Decision Document/Closure Report is to provide justification and documentation supporting the recommendation that no further corrective action is needed for CAU 105 based on the implementation of the corrective actions. Corrective action investigation (CAI) activities were performed from October 22, 2012, through May 23, 2013, as set forth in the Corrective Action Investigation Plan for Corrective Action Unit 105: Area 2 Yucca Flat Atmospheric Test Sites; and in accordance with the Soils Activity Quality Assurance Plan, which establishes requirements, technical planning, and general quality practices.

Matthews, Patrick

2014-01-01T23:59:59.000Z

480

Software Design Document, Testing, Deployment and Configuration Management, and User Manual of the UUIS -- a Team 4 COMP5541-W10 Project Approach  

E-Print Network [OSTI]

This document provides a description of the technical design for Unified University Inventory System - Web Portal. This document's primary purpose is to describe the technical vision for how business requirements will be realized. This document provides an architectural overview of the system to depict different aspects of the system. This document also functions as a foundational reference point for developers.

Sobh, Kanj; Liu, Bing; Mayantz, Max; Zhang, Yu Ming; Alhazmi, Ali; de Bled, Robin; Al-Sharawi, Abdulrahman

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "technical support document" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Independent technical review, handbook  

SciTech Connect (OSTI)

Purpose Provide an independent engineering review of the major projects being funded by the Department of Energy, Office of Environmental Restoration and Waste Management. The independent engineering review will address questions of whether the engineering practice is sufficiently developed to a point where a major project can be executed without significant technical problems. The independent review will focus on questions related to: (1) Adequacy of development of the technical base of understanding; (2) Status of development and availability of technology among the various alternatives; (3) Status and availability of the industrial infrastructure to support project design, equipment fabrication, facility construction, and process and program/project operation; (4) Adequacy of the design effort to provide a sound foundation to support execution of project; (5) Ability of the organization to fully integrate the system, and direct, manage, and control the execution of a complex major project.

Not Available

1994-02-01T23:59:59.000Z

482

Research Data Management - Documentation  

E-Print Network [OSTI]

This short (16 slide) presentation "Documentation" explains the need to create documentation using several clear examples of the benefits from good documentation (and what can happen if it is not good), making research reproducible...

Collins, Anna

2013-01-01T23:59:59.000Z

483

Honda Transmission Technical Center  

High Performance Buildings Database

Russells Point, OH The Honda Transmission Technical Center is located on the Honda of America Manufacturing Plant facility site in Russells Point, Ohio. This facility is used for product engineering and market quality testing and analysis of automatic transmissions. The building contains a large workshop area for ten cars, a future dynamometer, two laboratories, an open office area, three conference rooms, a break room, restrooms, and related support areas.

484

Technical planning activity: Final report  

SciTech Connect (OSTI)

In April 1985, the US Department of Energy's (DOE's) Office of Fusion Energy commissioned the Technical Planning Activity (TPA). The purpose of this activity was to develop a technical planning methodology and prepare technical plans in support of the strategic and policy framework of the Magnetic Fusion Program Plan issued by DOE in February 1985. Although this report represents the views of only the US magnetic fusion community, it is international in scope in the sense that the technical plans contained herein describe the full scope of the tasks that are prerequisites for the commercialization of fusion energy. The TPA has developed a well-structured methodology that includes detailed definitions of technical issues, definitions of program areas and elements, statements of research and development objectives, identification of key decision points and milestones, and descriptions of facility requirements.

Not Available

1987-01-01T23:59:59.000Z

485

Technical Evaluation Summary of the In Situ Vitrification Melt Expulsion at the Oak Ridge National Laboratory on April 21, 1996, Oak Ridge, Tennessee  

SciTech Connect (OSTI)

This Technical Evaluation Summary of the In Situ Vitrification Melt Expulsion at the Oak Ridge National Laboratory on April 21, 1996, was prepared at the request of the Department of Energy as a supporting reference document for the Final Unusual Occurrence Report to fully explore the probable causes that lead to the subject incident. This document provides the Environmental Restoration Program with the technical information on the performance of the in situ vitrification treatability study operations at ORNL pit 1 up to and including the time of the melt expulsion incident. This document also attempts to diagnose the causes of the melt expulsion event the consequent damages to equipment the radiological impacts of the event, and the equipment design modifications and procedural changes necessary for future safe ISV operations.

NONE

1996-11-01T23:59:59.000Z

486

Comparisons of ANS, ASME, AWS, and NFPA standards cited in the NRC standard review plan, NUREG-0800, and related documents  

SciTech Connect (OSTI)

This report provides the results of comparisons of the cited and latest versions of ANS, ASME, AWS and NFPA standards cited in the NRC Standard Review Plan for the Review of Safety Analysis Reports for Nuclear Power Plants (NUREG 0800) and related documents. The comparisons were performed by Battelle Pacific Northwest Laboratories in support of the NRC`s Standard Review Plan Update and Development Program. Significant changes to the standards, from the cited version to the latest version, are described and discussed in a tabular format for each standard. Recommendations for updating each citation in the Standard Review Plan are presented. Technical considerations and suggested changes are included for related regulatory documents (i.e., Regulatory Guides and the Code of Federal Regulations) citing the standard. The results and recommendations presented in this document have not been subjected to NRC staff review.

Ankrum, A.R.; Bohlander, K.L.; Gilbert, E.R.; Spiesman, J.B. [Pacific Northwest Lab., Richland, WA (United States)

1995-11-01T23:59:59.000Z

487

Technical abstracts: Mechanical engineering, 1990  

SciTech Connect (OSTI)

This document is a compilation of the published, unclassified abstracts produced by mechanical engineers at Lawrence Livermore National Laboratory (LLNL) during the calendar year 1990. Many abstracts summarize work completed and published in report form. These are UCRL-JC series documents, which include the full text of articles to be published in journals and of papers to be presented at meetings, and UCID reports, which are informal documents. Not all UCIDs contain abstracts: short summaries were generated when abstracts were not included. Technical Abstracts also provides descriptions of those documents assigned to the UCRL-MI (miscellaneous) category. These are generally viewgraphs or photographs presented at meetings. An author index is provided at the back of this volume for cross referencing.

Broesius, J.Y. (comp.)

1991-03-01T23:59:59.000Z

488

Decommissioning Documents | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Decommissioning Documents Decommissioning Documents More Documents & Publications Decommissioning Benchmarking Study Final Report Decommissioning Handbook dgappendices.pdf...

489

Roadmap and Technical White Papers for 21st Century Truck Partnership...  

Broader source: Energy.gov (indexed) [DOE]

Roadmap and Technical White Papers for 21st Century Truck Partnership Roadmap and Technical White Papers for 21st Century Truck Partnership Roadmap document for 21st Century Truck...

490

FY 06 Status of System Interface and Support Systems R&D Areas  

SciTech Connect (OSTI)

This document provides a summary of research and development activities performed in the Systems Interface and Support Systems area of the DOE Nuclear Hydrogen Initiative during FY 2006. Project cost and performance data obtained from the PICS system are presented and analyzed. Brief summaries of accomplishments and references are provided. A mapping of System Interface and Support Systems technical issues versus the work performed is updated and presented. Lastly, near-term research plans are given, and a description of the new UNLV high temperature heat exchanger program structure is provided.

S.R. Sherman

2006-09-01T23:59:59.000Z

491

LWR Sustainability Program Documents  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

References LWRS Program Reports Technical Integration Office Light Water Reactor Sustainability Program Accomplishments Report, 2014. pdf Light Water Reactor Sustainability...

492

A Document Navigation System for the Paperwork An electronic filing system won't make documentation any easier unless a company  

E-Print Network [OSTI]

, and Geoffrey D. V. Salter Managing and locating technical documents is a serious challenge for medical device and expensive online document management systems. However, most small organizations passed the responsibility into the scavenger hunt while management fumes at the lost productivity. When the document is found, it's time

Loeb, Gerald E.

493

Technical Sessions  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security AdministrationcontrollerNanocrystallineForeign ObjectOUR8, 2013Battelle:Technical Services Technical

494

Technical Standards  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas ConchasPassiveSubmittedStatus TomAboutManusScience and Innovation » TechnicalTechnicalReview

495

ELECTRICAL POWER SYSTEM DESCRIPTION DOCUMENT  

SciTech Connect (OSTI)

The purpose of this revision of the System Description Document (SDD) is to establish requirements that drive the design of the electrical power system and their bases to allow the design effort to proceed to License Application. This SDD is a living document that will be revised at strategic points as the design matures over time. This SDD identifies the requirements and describes the system design as they exist at this time, with emphasis on those attributes of the design provided to meet the requirements. This SDD has been developed to be an engineering tool for design control. Accordingly, the primary audience are design engineers. This type of SDD leads and follows the design process. It leads the design process with regard to the flow down of upper tier requirements onto the system. Knowledge of these requirements is essential to performing the design process. This SDD follows the design with regard to the description of the system. The description provided in the SDD is a reflection of the results of the design process to date. Functional and operational requirements applicable to this system are obtained from ''Project Functional and Operational Requirements'' (F&OR) (Siddoway, 2003). Other requirements to support the design process have been taken from higher level requirements documents such as ''Project Design Criteria Document'' (PDC) (Doraswamy 2004), the fire hazards analyses, and the preclosure safety analysis. The above mentioned low-level documents address ''Project Requirements Document'' (PRD) (Canori and Leitner 2003) requirements. This SDD includes several appendices with supporting information. Appendix B lists key system charts, diagrams, drawings, and lists; and Appendix C is a list of system procedures.

M. Maniyar

2004-06-22T23:59:59.000Z

496

Cumulative Effects of Micro-Hydro Development on the Fisheries of the Swan River Drainage, Montana, Volume II, Technical Information, 1983-1984 Final Report.  

SciTech Connect (OSTI)

This report summarizes a study to determine the potential cumulative effects of proposed small hydro development on the fisheries of the Swan River drainage. This report contains technical information and is a support document for the main report (Leathe and Enk, 1985). Consequently, discussion of results was minimized. The sections on fish population monitoring, streambed monitoring, habitat survey comparisons, and water temperature are the only portions that were not discussed in the main report. 5 refs., 55 figs., 44 tabs.

Leathe, Stephen A.

1985-07-01T23:59:59.000Z

497

Solicitation and Selection of Partner Projects, Technical Team Leads, and Measurement and Validation Contractors for the American Recovery and Reinvestment Act (ARRA) Funded Commercial Building Partnerships (CBP-2)  

SciTech Connect (OSTI)

In March 2010, Pacific Northwest National Laboratory (PNNL) joined two other labs receiving ARRA funding, Lawrence Berkeley National Laboratory (LBNL) and the National Renewable National Laboratory (NREL), to began weekly conference calls with the goal of coordinating a joint lab solicitation to support the ARRA-funded CBP project. Two solicitations were identified for: 1) new CBP Partners; 2) technical contractors to provide technical assistance and measurement and verification (M&V) contractors. The M&V contractors support the work by providing model reviews and conducting monitoring studies to verify building performance. This report documents the process used by the labs for the solicitations, and describes the process and outcomes for PNNL, selection of candidate Partners, technical teams, and M&V contractors.

Nesse, Ronald J.; Baechler, Michael C.; Iverson, Megan M.

2010-09-30T23:59:59.000Z

498

Technical Qualification Program Description - Integrated Support...  

Broader source: Energy.gov (indexed) [DOE]

* Creates participant's initial electronic TQP record on the DOE Employee Self Service (ESS) website. * Notifies employees when TQP record is created or updated in ESS. * Reviews...

499

PRELIMINARY TECHNICAL SUPPORT ENERGY EFFICIENCY PROGRAM  

E-Print Network [OSTI]

......................................................................ES-4 ES.3.1 Market and Technology Assessment Office of Energy Efficiency and Renewable Energy Building Technologies Program Appliances and Commercial

500

ALARA Training for Technical Support Personnel  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of EnergyEnergy Cooperation |South Valley ResponsibleSubmissionofDepartmentNo.7-05