National Library of Energy BETA

Sample records for tandem differential mobility

  1. ARM: AOS Humidified Tandem Differential Mobility Analyzer (Dataset...

    Office of Scientific and Technical Information (OSTI)

    Title: ARM: AOS Humidified Tandem Differential Mobility Analyzer AOS Humidified Tandem Differential Mobility Analyzer Authors: Scott Smith ; Cynthia Salwen ; Janek Uin ; Alice ...

  2. An Overview of the SGP Tandem Differential Mobility Analyzer

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    An Overview of the SGP Tandem Differential Mobility Analyzer Collins, Don Texas A&M University Spencer, Chance Texas A&M University Category: Instruments A differential mobility analyzer / tandem differential mobility analyzer (DMA / TDMA) system was integrated into the Aerosol Observing System (AOS) trailer at the SGP site in September, 2005. This instrument is used to continuously characterize the size-resolved concentration, hygroscopicity, and volatility of submicron particles. These

  3. Tandem Differential Mobility Analyzer/Aerodynamic Particle Sizer (APS) Handbook

    SciTech Connect (OSTI)

    Collins, D

    2010-06-18

    The tandem differential mobility analyzer (TDMA) is a single instrument that cycles through a series of complementary measurements of the physical properties of size-resolved submicron particles. In 2008, the TDMA was augmented through the addition of an aerodynamic particle sizer (APS), which extends the upper limit of the measured size distribution into the supermicron range. These two instruments are operated in parallel, but because they are controlled by a common computer and because the size distributions measured by the two are integrated in the produced datastreams, they are described together here. Throughout the day, the TDMA sequentially measures submicron aerosol size distributions and size-resolved hygroscopic growth distributions. More specifically, the instrument is operated as a scanning DMA to measure size distributions and as a TDMA to measure size-resolved hygroscopicity. A typical measurement sequence requires roughly 45 minutes. Each morning additional measurements are made of the relative humidity (RH) dependent hygroscopicity and temperature-dependent volatility of size-resolved particles. When the outside temperature and RH are within acceptable ranges, the hydration state of size-resolved particles is also characterized. The measured aerosol distributions complement the array of aerosol instruments in the Aerosol Observing System (AOS) and provide additional details of the light-scattering and cloud-nucleating characteristics of the aerosol.

  4. DOE SC ARM TR 161 Humidified Tandem Differential Mobility Analyzer Instrument Handbook

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1 3002 Humidified Tandem Differential Mobility Analyzer Instrument Handbook J Uin March 2016 DISCLAIMER This report was prepared as an account of work sponsored by the U.S. Government. Neither the United States nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not

  5. Tandem mobile robot system

    DOE Patents [OSTI]

    Buttz, James H.; Shirey, David L.; Hayward, David R.

    2003-01-01

    A robotic vehicle system for terrain navigation mobility provides a way to climb stairs, cross crevices, and navigate across difficult terrain by coupling two or more mobile robots with a coupling device and controlling the robots cooperatively in tandem.

  6. ARM - Field Campaign - ISDAC / RISCAM - Humidified Tandem Differential

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mobility Analyzer (HTDMA) / RISCAM - Humidified Tandem Differential Mobility Analyzer (HTDMA) ARM Data Discovery Browse Data Related Campaigns Indirect and Semi-Direct Aerosol Campaign (ISDAC) 2008.04.01, Ghan, AAF Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Campaign : ISDAC / RISCAM - Humidified Tandem Differential Mobility Analyzer (HTDMA) 2008.04.01 - 2008.06.30 Lead Scientist : Don Collins For data sets, see below. Abstract In

  7. Tandem robot control system and method for controlling mobile robots in tandem

    DOE Patents [OSTI]

    Hayward, David R.; Buttz, James H.; Shirey, David L.

    2002-01-01

    A control system for controlling mobile robots provides a way to control mobile robots, connected in tandem with coupling devices, to navigate across difficult terrain or in closed spaces. The mobile robots can be controlled cooperatively as a coupled system in linked mode or controlled individually as separate robots.

  8. Stackable differential mobility analyzer for aerosol measurement

    DOE Patents [OSTI]

    Cheng, Meng-Dawn; Chen, Da-Ren

    2007-05-08

    A multi-stage differential mobility analyzer (MDMA) for aerosol measurements includes a first electrode or grid including at least one inlet or injection slit for receiving an aerosol including charged particles for analysis. A second electrode or grid is spaced apart from the first electrode. The second electrode has at least one sampling outlet disposed at a plurality different distances along its length. A volume between the first and the second electrode or grid between the inlet or injection slit and a distal one of the plurality of sampling outlets forms a classifying region, the first and second electrodes for charging to suitable potentials to create an electric field within the classifying region. At least one inlet or injection slit in the second electrode receives a sheath gas flow into an upstream end of the classifying region, wherein each sampling outlet functions as an independent DMA stage and classifies different size ranges of charged particles based on electric mobility simultaneously.

  9. New Approaches to Differential Mobility Analysis for Airborne Measurements

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Approaches to Differential Mobility Analysis for Airborne Measurements Rick Flagan Chemical Engineering and Environmental Science and Engineering California Institute of Technology Pasadena, CA 91125 Support: NSF, ONR, Davidow Foundation Differential Mobility Analysis Air Sample Aerosol Charger/Neutralizer (Atmospheric Pressure Chemical Ionization) Sheath Air Q sh ~ 10 Q a Volumetric flow rate Q s Exhaust Q ex =Q sh Differential Mobility Analyzer DMA (Aerodynamic Analog of Sector Mass

  10. ARM: Tandem Differential Mobility Analyzer Aerosol Particle Sizer...

    Office of Scientific and Technical Information (OSTI)

    Subject: 54 Environmental Sciences Aerosol concentration; Aerosol particle size distribution; Hygroscopic growth; Particle number concentration; Particle size distribution Dataset ...

  11. Hooked differential mobility spectrometry apparatus and method therefore

    DOE Patents [OSTI]

    Shvartsburg, Alexandre A [Richland, WA; Tang, Keqi [Richland, WA; Ibrahim, Yehia M [Richland, WA; Smith, Richard D [Richland, WA

    2009-02-17

    Disclosed are a device and method for improved interfacing of differential mobility spectrometry (DMS) or field asymmetric waveform ion mobility spectrometry (FAIMS) analyzers of substantially planar geometry to subsequent or preceding instrument stages. Interfacing is achieved using curved DMS elements, where a thick ion beam emitted by planar DMS analyzers or injected into them for ion filtering is compressed to the gap median by DMS ion focusing effect in a spatially inhomogeneous electric field. Resulting thinner beams are more effectively transmitted through necessarily constrained conductance limit apertures to subsequent instrument stages operated at a pressure lower than DMS, and/or more effectively injected into planar DMS analyzers. The technology is synergetic with slit apertures, slit aperture/ion funnels, and high-pressure ion funnel interfaces known in the art which allow for increasing cross-sectional area of MS inlets. The invention may be used in integrated analytical platforms, including, e.g., DMS/MS, LC/DMS/MS, and DMS/IMS/MS that could replace and/or enhance current LC/MS methods, e.g., for proteomics research.

  12. Differential Microscopic Mobility of Components within a Deep Eutectic Solvent

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Wagle, Durgesh V.; Baker, Gary A.; Mamontov, Eugene

    2015-07-13

    From macroscopic measurements of deep eutectic solvents such as glyceline (1:2 molar ratio of choline chloride to glycerol), the long-range translational diffusion of the larger cation (choline) is known to be slower compared to that of the smaller hydrogen bond donor (glycerol). However, when the diffusion dynamics are analyzed on the subnanometer length scale, we discover that the displacements associated with the localized diffusive motions are actually larger for choline. This counterintuitive diffusive behavior can be understood as follows. The localized diffusive motions confined in the transient cage of neighbor particles, which precede the cage-breaking long-range diffusion jumps, are moremore » spatially constrained for glycerol than for choline because of the stronger hydrogen bonds the former makes with chloride anions. The implications of differential localized mobility of the constituents should be especially important for applications where deep eutectic solvents are confined on the nanometer length scale and their long-range translational diffusion is strongly inhibited (e.g., within microporous media).« less

  13. Differential Microscopic Mobility of Components within a Deep Eutectic Solvent

    SciTech Connect (OSTI)

    Wagle, Durgesh V.; Baker, Gary A.; Mamontov, Eugene

    2015-07-13

    From macroscopic measurements of deep eutectic solvents such as glyceline (1:2 molar ratio of choline chloride to glycerol), the long-range translational diffusion of the larger cation (choline) is known to be slower compared to that of the smaller hydrogen bond donor (glycerol). However, when the diffusion dynamics are analyzed on the subnanometer length scale, we discover that the displacements associated with the localized diffusive motions are actually larger for choline. This counterintuitive diffusive behavior can be understood as follows. The localized diffusive motions confined in the transient cage of neighbor particles, which precede the cage-breaking long-range diffusion jumps, are more spatially constrained for glycerol than for choline because of the stronger hydrogen bonds the former makes with chloride anions. The implications of differential localized mobility of the constituents should be especially important for applications where deep eutectic solvents are confined on the nanometer length scale and their long-range translational diffusion is strongly inhibited (e.g., within microporous media).

  14. High-Definition Differential Ion Mobility Spectrometry with Resolving Power up to 500

    SciTech Connect (OSTI)

    Shvartsburg, Alexandre A.; Seim, Thomas A.; Danielson, William F.; Norheim, Randolph V.; Moore, Ronald J.; Anderson, Gordon A.; Smith, Richard D.

    2013-01-20

    As the resolution of analytical methods improve, further progress tends to be increasingly limited by instrumental parameter instabilities that could be ignored before. This is now the case with differential ion mobility spectrometry (FAIMS), where fluctuations of the voltages and gas pressure have become critical. A new high-definition generator for FAIMS compensation voltage reported here provides a stable and accurate output than can be scanned with negligible steps. This reduces the spectral drift and peak width, thus improving the resolving power (R) and resolution. The gain for multiply-charged peptides that have narrowest peaks is up to ~40%, and R ~ 400 - 500 is achievable using He/N2 or H2/N2 gas mixtures.

  15. Tandem betatron

    DOE Patents [OSTI]

    Keinigs, Rhonald K.

    1992-01-01

    Two betatrons are provided in tandem for alternately accelerating an electron beam to avoid the single flux swing limitation of conventional betatrons and to accelerate the electron beam to high energies. The electron beam is accelerated in a first betatron during a period of increasing magnetic flux. The eletron beam is extracted from the first betatron as a peak magnetic flux is reached and then injected into a second betatron at a time of minimum magnetic flux in the second betatron. The cycle may be repeated until the desired electron beam energy is obtained. In one embodiment, the second betatron is axially offset from the first betatron to provide for electron beam injection directly at the axial location of the beam orbit in the second betatron.

  16. Mobility platform coupling device and method for coupling mobility platforms

    DOE Patents [OSTI]

    Shirey, David L.; Hayward, David R.; Buttz, James H.

    2002-01-01

    A coupling device for connecting a first mobility platform to a second mobility platform in tandem. An example mobility platform is a robot. The coupling device has a loose link mode for normal steering conditions and a locking position, tight link mode for navigation across difficult terrain and across obstacles, for traversing chasms, and for navigating with a reduced footprint in tight steering conditions.

  17. ARM - Measurement - Aerosol particle size distribution

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AOS : Aerosol Observing System CSPHOT : Cimel Sunphotometer HTDMA : Humidified Tandem Differential Mobility Analyzer SMPS : Scanning mobility particle sizer TDMA : Tandem...

  18. Ion mobility sensor system

    DOE Patents [OSTI]

    Xu, Jun; Watson, David B.; Whitten, William B.

    2013-01-22

    An ion mobility sensor system including an ion mobility spectrometer and a differential mobility spectrometer coupled to the ion mobility spectrometer. The ion mobility spectrometer has a first chamber having first end and a second end extending along a first direction, and a first electrode system that generates a constant electric field parallel to the first direction. The differential mobility spectrometer includes a second chamber having a third end and a fourth end configured such that a fluid may flow in a second direction from the third end to the fourth end, and a second electrode system that generates an asymmetric electric field within an interior of the second chamber. Additionally, the ion mobility spectrometer and the differential mobility spectrometer form an interface region. Also, the first end and the third end are positioned facing one another so that the constant electric field enters the third end and overlaps the fluid flowing in the second direction.

  19. Tandem resonator reflectance modulator

    DOE Patents [OSTI]

    Fritz, Ian J. (Albuquerque, NM); Wendt, Joel R. (Albuquerque, NM)

    1994-01-01

    A wide band optical modulator is grown on a substrate as tandem Fabry-Perot resonators including three mirrors spaced by two cavities. The absorption of one cavity is changed relative to the absorption of the other cavity by an applied electric field, to cause a change in total reflected light, as light reflecting from the outer mirrors is in phase and light reflecting from the inner mirror is out of phase with light from the outer mirrors.

  20. Tandem resonator reflectance modulator

    DOE Patents [OSTI]

    Fritz, I.J.; Wendt, J.R.

    1994-09-06

    A wide band optical modulator is grown on a substrate as tandem Fabry-Perot resonators including three mirrors spaced by two cavities. The absorption of one cavity is changed relative to the absorption of the other cavity by an applied electric field, to cause a change in total reflected light, as light reflecting from the outer mirrors is in phase and light reflecting from the inner mirror is out of phase with light from the outer mirrors. 8 figs.

  1. Monolithic tandem solar cell

    SciTech Connect (OSTI)

    Wanlass, Mark W.

    1991-01-01

    A single-crystal, monolithic, tandem, photovoltaic solar cell is described which includes (a) an InP substrate having upper and lower surfaces, (b) a first photoactive subcell on the upper surface of the InP substrate, and (c) a second photoactive subcell on the first subcell. The first photoactive subcell is GaInAsP of defined composition. The second subcell is InP. The two subcells are lattice matched. The solar cell can be provided as a two-terminal device or a three-terminal device.

  2. Monolithic tandem solar cell

    DOE Patents [OSTI]

    Wanlass, M.W.

    1994-06-21

    A single-crystal, monolithic, tandem, photovoltaic solar cell is described which includes (a) an InP substrate having upper and lower surfaces, (b) a first photoactive subcell on the upper surface of the InP substrate, (c) a second photoactive subcell on the first subcell; and (d) an optically transparent prismatic cover layer over the second subcell. The first photoactive subcell is GaInAsP of defined composition. The second subcell is InP. The two subcells are lattice matched. 9 figs.

  3. Monolithic tandem solar cell

    DOE Patents [OSTI]

    Wanlass, Mark W. (Golden, CO)

    1994-01-01

    A single-crystal, monolithic, tandem, photovoltaic solar cell is described which includes (a) an InP substrate having upper and lower surfaces, (b) a first photoactive subcell on the upper surface of the InP substrate, (c) a second photoactive subcell on the first subcell; and (d) an optically transparent prismatic cover layer over the second subcell. The first photoactive subcell is GaInAsP of defined composition. The second subcell is InP. The two subcells are lattice matched.

  4. Fueling of tandem mirror reactors

    SciTech Connect (OSTI)

    Gorker, G.E.; Logan, B.G.

    1985-01-01

    This paper summarizes the fueling requirements for experimental and demonstration tandem mirror reactors (TMRs), reviews the status of conventional pellet injectors, and identifies some candidate accelerators that may be needed for fueling tandem mirror reactors. Characteristics and limitations of three types of accelerators are described; neutral beam injectors, electromagnetic rail guns, and laser beam drivers. Based on these characteristics and limitations, a computer module was developed for the Tandem Mirror Reactor Systems Code (TMRSC) to select the pellet injector/accelerator combination which most nearly satisfies the fueling requirements for a given machine design.

  5. Nanocrystal assembly for tandem catalysis

    DOE Patents [OSTI]

    Yang, Peidong; Somorjai, Gabor; Yamada, Yusuke; Tsung, Chia-Kuang; Huang, Wenyu

    2014-10-14

    The present invention provides a nanocrystal tandem catalyst comprising at least two metal-metal oxide interfaces for the catalysis of sequential reactions. One embodiment utilizes a nanocrystal bilayer structure formed by assembling sub-10 nm platinum and cerium oxide nanocube monolayers on a silica substrate. The two distinct metal-metal oxide interfaces, CeO.sub.2--Pt and Pt--SiO.sub.2, can be used to catalyze two distinct sequential reactions. The CeO.sub.2--Pt interface catalyzed methanol decomposition to produce CO and H.sub.2, which were then subsequently used for ethylene hydroformylation catalyzed by the nearby Pt--SiO.sub.2 interface. Consequently, propanal was selectively produced on this nanocrystal bilayer tandem catalyst.

  6. "Nanocrystal bilayer for tandem catalysis"

    SciTech Connect (OSTI)

    Yamada, Yusuke; Tsung, Chia Kuang; Huang, Wenyu; Huo, Ziyang; E.Habas, Susan E; Soejima, Tetsuro; Aliaga, Cesar E; Samorjai, Gabor A; Yang, Peidong

    2011-01-24

    Supported catalysts are widely used in industry and can be optimized by tuning the composition and interface of the metal nanoparticles and oxide supports. Rational design of metal-metal oxide interfaces in nanostructured catalysts is critical to achieve better reaction activities and selectivities. We introduce here a new class of nanocrystal tandem catalysts that have multiple metal-metal oxide interfaces for the catalysis of sequential reactions. We utilized a nanocrystal bilayer structure formed by assembling platinum and cerium oxide nanocube monolayers of less than 10 nm on a silica substrate. The two distinct metal-metal oxide interfaces, CeO2-Pt and Pt-SiO2, can be used to catalyse two distinct sequential reactions. The CeO2-Pt interface catalysed methanol decomposition to produce CO and H2, which were subsequently used for ethylene hydroformylation catalysed by the nearby Pt-SiO2 interface. Consequently, propanal was produced selectively from methanol and ethylene on the nanocrystal bilayer tandem catalyst. This new concept of nanocrystal tandem catalysis represents a powerful approach towards designing high-performance, multifunctional nanostructured catalysts

  7. PROJECT PROFILE: Mechanically Stacked Hybrid Photovoltaic Tandems |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Mechanically Stacked Hybrid Photovoltaic Tandems PROJECT PROFILE: Mechanically Stacked Hybrid Photovoltaic Tandems Funding Opportunity: SuNLaMP SunShot Subprogram: Photovoltaics Location: National Renewable Energy Laboratory, Golden, CO Amount Awarded: $999,999 Tandem cell architectures present a path toward higher module efficiencies over single junction designs. This project will develop a gallium indium phosphide (GaInP) on silicon mechanically stacked voltage-matched

  8. Tandem mirror technology demonstration facility

    SciTech Connect (OSTI)

    Not Available

    1983-10-01

    This report describes a facility for generating engineering data on the nuclear technologies needed to build an engineering test reactor (ETR). The facility, based on a tandem mirror operating in the Kelley mode, could be used to produce a high neutron flux (1.4 MW/M/sup 2/) on an 8-m/sup 2/ test area for testing fusion blankets. Runs of more than 100 h, with an average availability of 30%, would produce a fluence of 5 mW/yr/m/sup 2/ and give the necessary experience for successful operation of an ETR.

  9. Tandem junction amorphous silicon solar cells

    DOE Patents [OSTI]

    Hanak, Joseph J.

    1981-01-01

    An amorphous silicon solar cell has an active body with two or a series of layers of hydrogenated amorphous silicon arranged in a tandem stacked configuration with one optical path and electrically interconnected by a tunnel junction. The layers of hydrogenated amorphous silicon arranged in tandem configuration can have the same bandgap or differing bandgaps.

  10. Tandem Mirror Reactor Systems Code (Version I)

    SciTech Connect (OSTI)

    Reid, R.L.; Finn, P.A.; Gohar, M.Y.; Barrett, R.J.; Gorker, G.E.; Spampinaton, P.T.; Bulmer, R.H.; Dorn, D.W.; Perkins, L.J.; Ghose, S.

    1985-09-01

    A computer code was developed to model a Tandem Mirror Reactor. Ths is the first Tandem Mirror Reactor model to couple, in detail, the highly linked physics, magnetics, and neutronic analysis into a single code. This report describes the code architecture, provides a summary description of the modules comprising the code, and includes an example execution of the Tandem Mirror Reactor Systems Code. Results from this code for two sensitivity studies are also included. These studies are: (1) to determine the impact of center cell plasma radius, length, and ion temperature on reactor cost and performance at constant fusion power; and (2) to determine the impact of reactor power level on cost.

  11. ARM - Field Campaign - Deployment of AAF Scanning Mobility Particle...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The SMPS was operated with a cloud condensation nuclei (CCN) counter. Aerosol particles were first classified by the differential mobility analyzer inside the SMPS, the classified ...

  12. Differentially pumped dual linear quadrupole ion trap mass spectrometer

    DOE Patents [OSTI]

    Owen, Benjamin C.; Kenttamaa, Hilkka I.

    2015-10-20

    The present disclosure provides a new tandem mass spectrometer and methods of using the same for analyzing charged particles. The differentially pumped dual linear quadrupole ion trap mass spectrometer of the present disclose includes a combination of two linear quadrupole (LQIT) mass spectrometers with differentially pumped vacuum chambers.

  13. ARM - Measurement - Aerosol scattering

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    : Nephelometer PASS : Photoacoustic Soot Spectrometer RL : Raman Lidar TDMA : Tandem Differential Mobility Analyzer Field Campaign Instruments AMT : Aerosol Modeling...

  14. High voltage series connected tandem junction solar battery

    DOE Patents [OSTI]

    Hanak, Joseph J.

    1982-01-01

    A high voltage series connected tandem junction solar battery which comprises a plurality of strips of tandem junction solar cells of hydrogenated amorphous silicon having one optical path and electrically interconnected by a tunnel junction. The layers of hydrogenated amorphous silicon, arranged in a tandem configuration, can have the same bandgap or differing bandgaps. The tandem junction strip solar cells are series connected to produce a solar battery of any desired voltage.

  15. Modelling of tandem cell temperature coefficients

    SciTech Connect (OSTI)

    Friedman, D.J.

    1996-05-01

    This paper discusses the temperature dependence of the basic solar-cell operating parameters for a GaInP/GaAs series-connected two-terminal tandem cell. The effects of series resistance and of different incident solar spectra are also discussed.

  16. MOBILITY AGREEMENT

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    MOBILITY AGREEMENT I hereby acknowledge that, as a condition of my employment as a Criminal Investigator with the Department of Energy, Office of Inspector General, I may be required to relocate to an OIG office in another geographic location based on the needs of the organization. I understand that my failure to accept such a directed reassignment could be a basis for my separation from the service. _______________________________ Signature Date

  17. Mobile Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    govSitesMobile Facility AMF Information Science Architecture Baseline Instruments AMF1 AMF2 AMF3 MAOS AMF Fact Sheet Images Contacts AMF Deployments McMurdo Station, Antarctica, 2015-2016 Pearl Harbor, Hawaii, to San Francisco, California, 2015 Hyytiälä, Finland, 2014 Manacapuru, Brazil, 2014 Oliktok Point, Alaska, 2013 Los Angeles, California, to Honolulu, Hawaii, 2012 Cape Cod, Massachusetts, 2012 Gan Island, Maldives, 2011 Ganges Valley, India, 2011 Steamboat Springs, Colorado, 2010

  18. Tandem microwave waste remediation and decontamination system

    DOE Patents [OSTI]

    Wicks, George G.; Clark, David E.; Schulz, Rebecca L.

    1999-01-01

    The invention discloses a tandem microwave system consisting of a primary chamber in which microwave energy is used for the controlled combustion of materials. A second chamber is used to further treat the off-gases from the primary chamber by passage through a susceptor matrix subjected to additional microwave energy. The direct microwave radiation and elevated temperatures provide for significant reductions in the qualitative and quantitative emissions of the treated off gases. The tandem microwave system can be utilized for disinfecting wastes, sterilizing materials, and/or modifying the form of wastes to solidify organic or inorganic materials. The simple design allows on-site treatment of waste by small volume waste generators.

  19. Cold Climate Heat Pumps Using Tandem Compressors

    SciTech Connect (OSTI)

    Shen, Bo; Abdelaziz, Omar; Rice, C Keith; Baxter, Van D

    2016-01-01

    In cold climate zones, e.g. ASHRAE climate regions IV and V, conventional electric air-source heat pumps (ASHP) do not work well, due to high compressor discharge temperatures, large pressure ratios and inadequate heating capacities at low ambient temperatures. Consequently, significant use of auxiliary strip heating is required to meet the building heating load. We introduce innovative ASHP technologies as part of continuing efforts to eliminate auxiliary strip heat use and maximize heating COP with acceptable cost-effectiveness and reliability. These innovative ASHP were developed using tandem compressors, which are capable of augmenting heating capacity at low temperatures and maintain superior part-load operation efficiency at moderate temperatures. Two options of tandem compressors were studied; the first employs two identical, single-speed compressors, and the second employs two identical, vapor-injection compressors. The investigations were based on system modeling and laboratory evaluation. Both designs have successfully met the performance criteria. Laboratory evaluation showed that the tandem, single-speed compressor ASHP system is able to achieve heating COP = 4.2 at 47 F (8.3 C), COP = 2.9 at 17 F (-8.3 C), and 76% rated capacity and COP = 1.9 at -13 F (-25 C). This yields a HSPF = 11.0 (per AHRI 210/240). The tandem, vapor-injection ASHP is able to reach heating COP = 4.4 at 47 F, COP = 3.1 at 17 F, and 88% rated capacity and COP = 2.0 at -13 F. This yields a HSPF = 12.0. The system modeling and further laboratory evaluation are presented in the paper.

  20. Current and lattice matched tandem solar cell

    DOE Patents [OSTI]

    Olson, Jerry M.

    1987-01-01

    A multijunction (cascade) tandem photovoltaic solar cell device is fabricated of a Ga.sub.x In.sub.1-x P (0.505.ltoreq.X.ltoreq.0.515) top cell semiconductor lattice matched to a GaAs bottom cell semiconductor at a low-resistance heterojunction, preferably a p+/n+ heterojunction between the cells. The top and bottom cells are both lattice matched and current matched for high efficiency solar radiation conversion to electrical energy.

  1. Low Cost, High Efficiency Tandem Silicon Solar Cells and LEDs...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Building Energy Efficiency Building Energy ... Return to Search Low Cost, High Efficiency Tandem Silicon Solar Cells and LEDs ... gaps will lead to efficient power conversion. ...

  2. High-efficiency, monolithic, multi-bandgap, tandem photovoltaic...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tidal Industrial Technologies Solar Photovoltaic Solar Thermal Startup America Vehicles ... High-efficiency, monolithic, multi-bandgap, tandem photovoltaic energy converters United ...

  3. Axisymmetric Tandem Mirror Magnetic Fusion Energy Power Plant...

    Office of Scientific and Technical Information (OSTI)

    A fusion power plant is described that utilizes a new version of the tandem mirror device including spinning liquid walls. The magnetic configuration is evaluated with an ...

  4. Axisymmetric Tandem Mirror Magnetic Fusion Energy Power Plant...

    Office of Scientific and Technical Information (OSTI)

    Magnetic Fusion Energy Power Plant with Thick Liquid-Walls Citation Details In-Document Search Title: Axisymmetric Tandem Mirror Magnetic Fusion Energy Power Plant with Thick ...

  5. Cooperating mobile robots

    DOE Patents [OSTI]

    Harrington, John J.; Eskridge, Steven E.; Hurtado, John E.; Byrne, Raymond H.

    2004-02-03

    A miniature mobile robot provides a relatively inexpensive mobile robot. A mobile robot for searching an area provides a way for multiple mobile robots in cooperating teams. A robotic system with a team of mobile robots communicating information among each other provides a way to locate a source in cooperation. A mobile robot with a sensor, a communication system, and a processor, provides a way to execute a strategy for searching an area.

  6. Method of fabricating bifacial tandem solar cells

    DOE Patents [OSTI]

    Wojtczuk, Steven J; Chiu, Philip T; Zhang, Xuebing; Gagnon, Edward; Timmons, Michael

    2014-10-07

    A method of fabricating on a semiconductor substrate bifacial tandem solar cells with semiconductor subcells having a lower bandgap than the substrate bandgap on one side of the substrate and with subcells having a higher bandgap than the substrate on the other including, first, growing a lower bandgap subcell on one substrate side that uses only the same periodic table group V material in the dislocation-reducing grading layers and bottom subcells as is present in the substrate and after the initial growth is complete and then flipping the substrate and growing the higher bandgap subcells on the opposite substrate side which can be of different group V material.

  7. A tandem-based compact dual-energy gamma generator

    SciTech Connect (OSTI)

    Persaud, A.; Kwan, J.W.; Leitner, M.; Leung, K.N.; Ludewigt, B.; Tanaka, N.; Waldron, W.; Wilde, S.; Antolak, A.J.; Morse, D.H.; Raber, T.

    2009-11-11

    A dual-energy tandem-type gamma generator has been developed at E.O. Lawrence Berkeley National Laboratory and Sandia National Laboratories. The tandem accelerator geometry allows higher energy nuclear reactions to be reached, thereby allowing more flexible generation of MeV-energy gammas for active interrogation applications.

  8. Parametric systems analysis for tandem mirror hybrids

    SciTech Connect (OSTI)

    Lee, J.D.; Chapin, D.L.; Chi, J.W.H.

    1980-09-01

    Fusion fission systems, consisting of fissile producing fusion hybrids combining a tandem mirror fusion driver with various blanket types and net fissile consuming LWR's, have been modeled and analyzed parametrically. Analysis to date indicates that hybrids can be competitive with mined uranium when U/sub 3/O/sub 8/ cost is about 100 $/lb., adding less than 25% to present day cost of power from LWR's. Of the three blanket types considered, uranium fast fission (UFF), thorium fast fission (ThFF), and thorium fission supressed (ThFS), the ThFS blanket has a modest economic advantage under most conditions but has higher support ratios and potential safety advantages under all conditions.

  9. MobileMatch App

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MobileMatch VolunteerMatch Mobile App MobileMatch is a mobile extension (app) to LANL's VolunteerMatch site that allows volunteers to search, sign up and track hours. Contact Giving Campaigns & Volunteering Debbi Wersonick Community Relations & Partnerships (505) 667-7870 Email Engage anytime, anywhere with this easy and intuitive tool! Using MobileMatch app is easy mobilematch-app Now LANL volunteers can search, sign up and track hours right on their mobile device. Get on the Volunteer

  10. Enhanced absorption in tandem solar cells by applying hydrogenated In{sub 2}O{sub 3} as electrode

    SciTech Connect (OSTI)

    Yin, Guanchao Manley, Phillip; Steigert, Alexander; Klenk, Reiner; Schmid, Martina

    2015-11-23

    To realize the high efficiency potential of perovskite/chalcopyrite tandem solar cells in modules, hydrogenated In{sub 2}O{sub 3} (IO:H) as electrode is investigated. IO:H with an electron mobility of 100 cm{sup 2} V{sup −1} s{sup −1} is demonstrated. Compared to the conventional Sn doped In{sub 2}O{sub 3} (ITO), IO:H exhibits a decreased electron concentration and leads to almost no sub-bandgap absorption up to the wavelength of 1200 nm. Without a trade-off between transparency and lateral resistance in the IO:H electrode, the tandem cell keeps increasing in efficiency as the IO:H thickness increases and efficiencies above 22% are calculated. In contrast, the cells with ITO as electrode perform much worse due to the severe parasitic absorption in ITO. This indicates that IO:H has the potential to lead to high efficiencies, which is otherwise constrained by the parasitic absorption in conventional transparent conductive oxide electrode for tandem solar cells in modules.

  11. Detached-Eddy Simulations and Noise Predictions for Tandem Cylinders |

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Argonne Leadership Computing Facility Flow visualization (snapshot of vorticity magnitude from DDES of the Tandem Cylinders). Dr. Mikhail Strelets, Dr. Mikhail Shur, and Dr. Andrey Travin, New Technologies and Services, Ltd. and Saint-Petersburg State Polytechnic University. Detached-Eddy Simulations and Noise Predictions for Tandem Cylinders PI Name: Philippe Spalart PI Email: philippe.r.spalart@boeing.com Institution: Boeing Allocation Program: INCITE Allocation Hours at ALCF: 45 Million

  12. Mobile Technology Management

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2014-05-15

    The order establishes requirements, assigns responsibilities, and provides guidance for federal mobile technology management and employee use of both government furnished and personally-owned mobile devices within DOE and NNSA. Establishes requirements for use of User Agreements to govern mobile devices used for official duties. Does not cancel other directives.

  13. An ion mobility mass spectrometer for investigating photoisomerization and photodissociation of molecular ions

    SciTech Connect (OSTI)

    Adamson, B. D.; Coughlan, N. J. A.; Markworth, P. B.; Bieske, E. J.; Continetti, R. E.

    2014-12-15

    An ion mobility mass spectrometry apparatus for investigating the photoisomerization and photodissociation of electrosprayed molecular ions in the gas phase is described. The device consists of a drift tube mobility spectrometer, with access for a laser beam that intercepts the drifting ion packet either coaxially or transversely, followed by a quadrupole mass filter. An ion gate halfway along the drift region allows the instrument to be used as a tandem ion mobility spectrometer, enabling mobility selection of ions prior to irradiation, with the photoisomer ions being separated over the second half of the drift tube. The utility of the device is illustrated with photoisomerization and photodissociation action spectra of carbocyanine molecular cations. The mobility resolution of the device for singly charged ions is typically 80 and it has a mass range of 100-440 Da, with the lower limit determined by the drive frequency for the ion funnels, and the upper limit by the quadrupole mass filter.

  14. Engineering problems of tandem-mirror reactors

    SciTech Connect (OSTI)

    Moir, R.W.; Barr, W.L.; Boghosian, B.M.

    1981-10-22

    We have completed a comparative evaluation of several end plug configurations for tandem mirror fusion reactors with thermal barriers. The axi-cell configuration has been selected for further study and will be the basis for a detailed conceptual design study to be carried out over the next two years. The axi-cell end plug has a simple mirror cell produced by two circular coils followed by a transition coil and a yin-yang pair, which provides for MHD stability. This paper discusses some of the many engineering problems facing the designer. We estimated the direct cost to be 2$/W/sub e/. Assuming total (direct and indirect) costs to be twice this number, we need to reduce total costs by factors between 1.7 and 2.3 to compete with future LWRs levelized cost of electricity. These reductions may be possible by designing magnets producing over 20T made possible by use of combinations of superconducting and normal conducting coils as well as improvements in performance and cost of neutral beam and microwave power systems. Scientific and technological understanding and innovation are needed in the area of thermal barrier pumping - a process by which unwanted particles are removed (pumped) from certain regions of velocity and real space in the end plug. Removal of exhaust fuel ions, fusion ash and impurities by action of a halo plasma and plasma dump in the mirror end region is another challenging engineering problem discussed in this paper.

  15. DIFFERENTIAL ANALYZER

    DOE Patents [OSTI]

    Sorensen, E.G.; Gordon, C.M.

    1959-02-10

    Improvements in analog eomputing machines of the class capable of evaluating differential equations, commonly termed differential analyzers, are described. In general form, the analyzer embodies a plurality of basic computer mechanisms for performing integration, multiplication, and addition, and means for directing the result of any one operation to another computer mechanism performing a further operation. In the device, numerical quantities are represented by the rotation of shafts, or the electrical equivalent of shafts.

  16. Ion mobility sensor

    DOE Patents [OSTI]

    Koo, Jackson C.; Yu, Conrad M.

    2005-08-23

    An ion mobility sensor which can detect both ion and molecules simultaneously. Thus, one can measure the relative arrival times between various ions and molecules. Different ions have different mobility in air, and the ion sensor enables measurement of ion mobility, from which one can identify the various ions and molecules. The ion mobility sensor which utilizes a pair of glow discharge devices may be designed for coupling with an existing gas chromatograph, where various gas molecules are already separated, but numbers of each kind of molecules are relatively small, and in such cases a conventional ion mobility sensor cannot be utilized.

  17. Energize Mobile | Open Energy Information

    Open Energy Info (EERE)

    Web Application Link: www.tendrilinc.comenergy-providersapplicationenergize Cost: Free Energize Mobile Screenshot References: Tendril1 Logo: Energize Mobile This...

  18. ARM Mobile Facilities

    SciTech Connect (OSTI)

    Orr, Brad; Coulter, Rich

    2010-12-13

    This video provides an overview of the ARM Mobile Facilities, two portable climate laboratories that can deploy anywhere in the world for campaigns of at least six months.

  19. Mobile Ice Nucleus Spectrometer

    SciTech Connect (OSTI)

    Kulkarni, Gourihar R.; Kok, G. L.

    2012-05-07

    This first year report presents results from a computational fluid dynamics (CFD) study to assess the flow and temperature profiles within the mobile ice nucleus spectrometer.

  20. ARM Mobile Facilities

    ScienceCinema (OSTI)

    Orr, Brad; Coulter, Rich

    2014-09-15

    This video provides an overview of the ARM Mobile Facilities, two portable climate laboratories that can deploy anywhere in the world for campaigns of at least six months.

  1. Mobile Technology Management

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2013-11-21

    The directive will ensure that federal organizations and employees within the Department can use mobile technology to support mission requirements in a safe and secure manner.

  2. Heavy Mobile Equipment Mechanic

    Broader source: Energy.gov [DOE]

    Join the Bonneville Power Administration (BPA) for a challenging and rewarding career, while working, living, and playing in the Pacific Northwest. The Heavy Mobile Equipment Mechanic (HMEM)...

  3. Counter-Rotating Tandem Motor Drilling System

    SciTech Connect (OSTI)

    Kent Perry

    2009-04-30

    Gas Technology Institute (GTI), in partnership with Dennis Tool Company (DTC), has worked to develop an advanced drill bit system to be used with microhole drilling assemblies. One of the main objectives of this project was to utilize new and existing coiled tubing and slimhole drilling technologies to develop Microhole Technology (MHT) so as to make significant reductions in the cost of E&P down to 5000 feet in wellbores as small as 3.5 inches in diameter. This new technology was developed to work toward the DOE's goal of enabling domestic shallow oil and gas wells to be drilled inexpensively compared to wells drilled utilizing conventional drilling practices. Overall drilling costs can be lowered by drilling a well as quickly as possible. For this reason, a high drilling rate of penetration is always desired. In general, high drilling rates of penetration (ROP) can be achieved by increasing the weight on bit and increasing the rotary speed of the bit. As the weight on bit is increased, the cutting inserts penetrate deeper into the rock, resulting in a deeper depth of cut. As the depth of cut increases, the amount of torque required to turn the bit also increases. The Counter-Rotating Tandem Motor Drilling System (CRTMDS) was planned to achieve high rate of penetration (ROP) resulting in the reduction of the drilling cost. The system includes two counter-rotating cutter systems to reduce or eliminate the reactive torque the drillpipe or coiled tubing must resist. This would allow the application of maximum weight-on-bit and rotational velocities that a coiled tubing drilling unit is capable of delivering. Several variations of the CRTDMS were designed, manufactured and tested. The original tests failed leading to design modifications. Two versions of the modified system were tested and showed that the concept is both positive and practical; however, the tests showed that for the system to be robust and durable, borehole diameter should be substantially larger than

  4. UPGRADE AND OPERATION OF THE BNL TANDEMS FOR RHIC INJECTION.

    SciTech Connect (OSTI)

    STESKI,D.B.; ALESSI,J.; BENJAMIN,J.; CARLSON,C.; MANNI,M.; THIEBERGER,P.; WIPLICH,M.

    2001-06-18

    One of the tandem Van de Graaffs (MP7) at Brookhaven National Laboratory (BNL) has successfully completed its first year as an injector for the Relativistic Heavy Ion Collider (RHIC). The tandem provided pulsed beam of Au{sup +32} (peak intensity 80 e{mu}A, 500{micro}s) with only 17 hours of downtime during a 5 month run. Improvements are being made to further increase the intensity of the gold beam for the experimental run starting in 2001. A second tandem Van de Graaff (MP6) has been extensively upgraded and can now reach a terminal voltage of over 14MV. A beamline has been constructed to transport the MP6 beam around MP7 and then connect to the existing MP7 beamlines. This has allowed MP6 to deliver beam to local target rooms for an outside user program, while MP7 has simultaneously injected RHIC. MP6 can also be used as an injector for RHIC.

  5. PROJECT PROFILE: Silicon-Based Tandem Solar Cells | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Silicon-Based Tandem Solar Cells PROJECT PROFILE: Silicon-Based Tandem Solar Cells Funding Opportunity: SuNLaMP SunShot Subprogram: Photovoltaics Location: National Renewable Energy Laboratory, Golden, CO Amount Awarded: $1,500,000 The project will demonstrate bonded gallium indium phosphide (GaInP) on silicon tandem cells, evaluate the advantages and disadvantages of this method of forming higher-efficiency tandem cells, and compare two- and three-terminal device configurations. APPROACH In

  6. Ion mobility analysis of lipoproteins

    DOE Patents [OSTI]

    Benner, W. Henry; Krauss, Ronald M.; Blanche, Patricia J.

    2007-08-21

    A medical diagnostic method and instrumentation system for analyzing noncovalently bonded agglomerated biological particles is described. The method and system comprises: a method of preparation for the biological particles; an electrospray generator; an alpha particle radiation source; a differential mobility analyzer; a particle counter; and data acquisition and analysis means. The medical device is useful for the assessment of human diseases, such as cardiac disease risk and hyperlipidemia, by rapid quantitative analysis of lipoprotein fraction densities. Initially, purification procedures are described to reduce an initial blood sample to an analytical input to the instrument. The measured sizes from the analytical sample are correlated with densities, resulting in a spectrum of lipoprotein densities. The lipoprotein density distribution can then be used to characterize cardiac and other lipid-related health risks.

  7. ARM - Measurement - Aerosol concentration

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CSPHOT : Cimel Sunphotometer CPC : Condensation Particle Counter HTDMA : Humidified Tandem Differential Mobility Analyzer IAP : In-situ Aerosol Profiles (Cessna Aerosol Flights)...

  8. ARM - Measurement - Aerosol composition

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    quality assurance purposes. ARM Instruments PILS : Particle Into Liquid Sampler TDMA : Tandem Differential Mobility Analyzer Field Campaign Instruments AEROSMASSSPEC : Aerosol Mass...

  9. ARM - Measurement - Cloud condensation nuclei

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AOS : Aerosol Observing System CCN : Cloud Condensation Nuclei Particle Counter TDMA : Tandem Differential Mobility Analyzer Field Campaign Instruments AMT : Aerosol Modeling...

  10. ARM XDC Datastreams

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Information updated on April 8, 2010, 9:05 pm GMT General Data Description The Tandem Differential Mobility Analyzer (TDMA) is an instrument to measure dry size...

  11. ARM - Measurement - Aerosol particle size

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SPLATT-II : Single Particle Laser Ablasion Time flown on Aircraft TDMA-AIR : Tandem Differential Mobility Analyzer- Airborne UW-CONVAIR580 : University of Washington...

  12. Search for: All records | Data Explorer

    Office of Scientific and Technical Information (OSTI)

    Anne Jefferson (27) Gunnar Senum (27) Janek Uin (27) Scott Smith (27) Bill Behrens (26) ... ARM: AOS Humidified Tandem Differential Mobility Analyzer Scott Smith ; Cynthia Salwen ; ...

  13. Search for: All records | Data Explorer

    Office of Scientific and Technical Information (OSTI)

    Cynthia Salwen (1) Gunnar Senum (1) Janek Uin (1) Scott Smith (1) Stephen Springston (1) ... ARM: AOS Humidified Tandem Differential Mobility Analyzer Scott Smith ; Cynthia Salwen ; ...

  14. Search for: All records | Data Explorer

    Office of Scientific and Technical Information (OSTI)

    Manvendra Dubey (23) Thomas Watson (23) Scott Smith (8) Robert Bullard (5) Alice Cialella ... ARM: AOS Humidified Tandem Differential Mobility Analyzer Scott Smith ; Cynthia Salwen ; ...

  15. ARM - Field Campaign - Indirect and Semi-Direct Aerosol Campaign...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Measurements 2009.04.07, Lubin, NSA ISDAC RISCAM - Humidified Tandem Differential Mobility Analyzer (HTDMA) 2008.04.01, Collins, NSA ISDAC - NASA ARCTAS Coordination with ...

  16. Summary of results from the Tandem Mirror Experiment (TMX)

    SciTech Connect (OSTI)

    Simonen, T.C.

    1981-02-26

    This report summarizes results from the successful experimental operation of the Tandem Mirror Experiment (TMX) over the period October 1978 through September 1980. The experimental program, summarized by the DOE milestones given in Table 1-1, had three basic phases: (1) an 8-month checkout period, October 1978 through May 1979; (2) a 6-month initial period of operation, June through November 1979, during which the basic principles of the tandem configuration were demonstrated (i.e., plasma confinement was improved over that of a single-cell mirror); and (3) a 10-month period, December 1979 through September 1980, during which the initial TMX results were corroborated by additional diagnostic measurements and many detailed physics investigations were carried out. This report summarizes the early results, presents results of recent data analysis, and outlines areas of ongoing research and data analysis which will be reported in future journal publications.

  17. Single P-N junction tandem photovoltaic device

    DOE Patents [OSTI]

    Walukiewicz, Wladyslaw; Ager, III, Joel W.; Yu, Kin Man

    2012-03-06

    A single P-N junction solar cell is provided having two depletion regions for charge separation while allowing the electrons and holes to recombine such that the voltages associated with both depletion regions of the solar cell will add together. The single p-n junction solar cell includes an alloy of either InGaN or InAlN formed on one side of the P-N junction with Si formed on the other side in order to produce characteristics of a two junction (2J) tandem solar cell through only a single P-N junction. A single P-N junction solar cell having tandem solar cell characteristics will achieve power conversion efficiencies exceeding 30%.

  18. Single P-N junction tandem photovoltaic device

    DOE Patents [OSTI]

    Walukiewicz, Wladyslaw; Ager, III, Joel W.; Yu, Kin Man

    2011-10-18

    A single P-N junction solar cell is provided having two depletion regions for charge separation while allowing the electrons and holes to recombine such that the voltages associated with both depletion regions of the solar cell will add together. The single p-n junction solar cell includes an alloy of either InGaN or InAlN formed on one side of the P-N junction with Si formed on the other side in order to produce characteristics of a two junction (2J) tandem solar cell through only a single P-N junction. A single P-N junction solar cell having tandem solar cell characteristics will achieve power conversion efficiencies exceeding 30%.

  19. High-efficiency, monolithic, multi-bandgap, tandem photovoltaic energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    converters - Energy Innovation Portal High-efficiency, monolithic, multi-bandgap, tandem photovoltaic energy converters National Renewable Energy Laboratory Contact NREL About This Technology Technology Marketing Summary Matching a semiconductor's bandgap to incident photon energy is a well-known method to achieve the most efficient photovoltaic devices. Since solar radiation consists of a wide range of wavelengths, having one semiconductor with a single bandgap to absorb all solar radiation

  20. Argonne Tandem Linac Accelerator System (ATLAS) Fact Sheet | Argonne

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    National Laboratory Argonne Tandem Linac Accelerator System (ATLAS) Fact Sheet The ATLAS facility is a leading facility for nuclear structure research in the United States. Any stable ion can be accelerated in ATLAS, the world's first superconducting linear accelerator for ions, and delivered to one of its several target stations. It provides a wide range of beams for nuclear reaction and structure research to a large community of users from the United States and abroad. About 20% of

  1. Charge exchange cooling in the tandem mirror plasma confinement apparatus

    DOE Patents [OSTI]

    Logan, B. Grant

    1978-01-01

    Method and apparatus for cooling a plasma of warm charged species confined in the center mirror cell of the tandem mirror apparatus by injecting cold neutral species of the plasma into at least one mirroring region of the center mirror cell, the cooling due to the loss of warm charged species through charge exchange with the cold neutral species with resulting diffusion of the warm neutral species out of the plasma.

  2. Intelligent mobile security systems

    SciTech Connect (OSTI)

    Allen, M.S. )

    1991-01-01

    This paper reports that mobile security systems are becoming increasingly important to military (Army, Air Force) and non-military (Drug Enforcement Agency, Border Patrol) organizations as the level and sophistication of terrorist activity increases. Frequently, organizations are required to deploy at remote sites on little notice. To ensure protection of life and equipment, security systems are sometimes required. Often, the personnel deployed on these missions are not adequately trained in the selection, installation, and operation of today's complex security equipment. The Intelligent Mobile Security System (IMSS) concept, as being developed by Sandia National Laboratories (SNL), allows untrained, non-technical personnel to configure, deploy, operate, and troubleshoot temporary/mobile physical security system. The IMSS may be used at nuclear facilities.

  3. Correlation ion mobility spectroscopy

    DOE Patents [OSTI]

    Pfeifer, Kent B.; Rohde, Steven B.

    2008-08-26

    Correlation ion mobility spectrometry (CIMS) uses gating modulation and correlation signal processing to improve IMS instrument performance. Closely spaced ion peaks can be resolved by adding discriminating codes to the gate and matched filtering for the received ion current signal, thereby improving sensitivity and resolution of an ion mobility spectrometer. CIMS can be used to improve the signal-to-noise ratio even for transient chemical samples. CIMS is especially advantageous for small geometry IMS drift tubes that can otherwise have poor resolution due to their small size.

  4. Benefits of Using Mobile Transformers and Mobile Substations for Rapidly

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Restoring Electrical Service: a Report to the United States Congress Pursuant to Section 1816 of the Energy Policy Act of 2005 (August 2006) | Department of Energy Using Mobile Transformers and Mobile Substations for Rapidly Restoring Electrical Service: a Report to the United States Congress Pursuant to Section 1816 of the Energy Policy Act of 2005 (August 2006) Benefits of Using Mobile Transformers and Mobile Substations for Rapidly Restoring Electrical Service: a Report to the United

  5. Mobile lighting apparatus

    DOE Patents [OSTI]

    Roe, George Michael; Klebanoff, Leonard Elliott; Rea, Gerald W; Drake, Robert A; Johnson, Terry A; Wingert, Steven John; Damberger, Thomas A; Skradski, Thomas J; Radley, Christopher James; Oros, James M; Schuttinger, Paul G; Grupp, David J; Prey, Stephen Carl

    2013-05-14

    A mobile lighting apparatus includes a portable frame such as a moveable trailer or skid having a light tower thereon. The light tower is moveable from a stowed position to a deployed position. A hydrogen-powered fuel cell is located on the portable frame to provide electrical power to an array of the energy efficient lights located on the light tower.

  6. Mobil lube dewaxing technologies

    SciTech Connect (OSTI)

    Baker, C.L.; McGuiness, M.P.

    1995-09-01

    Currently, the lube refining industry is in a period of transition, with both hydroprocessing and catalytic dewaxing gathering momentum as replacements for solvent extraction and solvent dewaxing. In addition, lube product quality requirements have been increasing, both in the US and abroad. Mobil has developed a broad array of dewaxing catalytic technologies which can serve refiners throughout the stages of this transition. In the future, lube feedstocks which vary in source and wax content will become increasingly important, requiring an optimized system for highest performance. The Mobil Lube Dewaxing (MLDW) process is the work-horse of the catalytic dewaxing technologies, being a robust, low cost technology suitable for both solvent extracted and hydrocracked feeds. The Mobil Selective Dewaxing (MSDW) process has been recently introduced in response to the growth of hydroprocessing. MSDW requires either severely hydrotreated or hydrocracked feeds and provides improved lube yields and VI. For refiners with hydrocrackers and solvent dewaxing units, Mobil Wax Isomerization (MWI) technology can make higher VI base stocks to meet the growing demand for very high quality lube products. A review of these three technologies is presented in this paper.

  7. Mobility Agreement for Criminal Investigators | Department of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Mobility Agreement for Criminal Investigators Mobility Agreement for Criminal Investigators PDF icon Mobility Agreement More Documents & Publications Semiannual Report to Congress: ...

  8. New Tandem Catalytic Cycles take to the Rhod(ium) | The Ames...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    New Tandem Catalytic Cycles take to the Rhod(ium) Light, combined with a novel rhodium catalyst, enables greener production of chemical feedstocks from biorenewables. A key...

  9. Long range hopping mobility platform.

    SciTech Connect (OSTI)

    Spletzer, Barry Louis; Fischer, Gary John

    2003-03-01

    Sandia National Laboratories has developed a mesoscale hopping mobility platform (Hopper) to overcome the longstanding problems of mobility and power in small scale unmanned vehicles. The system provides mobility in situations such as negotiating tall obstacles and rough terrain that are prohibitive for other small ground base vehicles. The Defense Advanced Research Projects Administration (DARPA) provided the funding for the hopper project.

  10. Current- and lattice-matched tandem solar cell

    DOE Patents [OSTI]

    Olson, J.M.

    1985-10-21

    A multijunction (cascade) tandem photovoltaic solar cell device is fabricated of a Ga/sub x/In/sub 1-x/P (0.505 equal to or less than x equal to or less than 0.515) top cell semiconductor lattice-matched to a GaAs bottom cell semiconductor at a low resistance heterojunction, preferably a p/sup +//n/sup +/ heterojunction between the cells. The top and bottom cells are both lattice-matched and current-matched for high efficiency solar radiation conversion to electrical energy.

  11. Ion Mobility Spectrometry (IMS) and Mass Spectrometry

    SciTech Connect (OSTI)

    Shvartsburg, Alexandre A.

    2010-04-20

    In a media of finite viscosity, the Coulomb force of external electric field moves ions with some terminal speed. This dynamics is controlled by “mobility” - a property of the interaction potential between ions and media molecules. This fact has been used to separate and characterize gas-phase ions in various modes of ion mobility spectrometry (IMS) developed since 1970. Commercial IMS devices were introduced in 1980-s for field detection of volatile traces such as explosives and chemical warfare agents. Coupling to soft-ionization sources, mass spectrometry (MS), and chromatographic methods in 1990-s had allowed IMS to handle complex samples, enabling new applications in biological and environmental analyses, nanoscience, and other areas. Since 2003, the introduction of commercial systems by major instrument vendors started bringing the IMS/MS capability to broad user community. The other major development of last decade has been the differential IMS or “field asymmetric waveform IMS” (FAIMS) that employs asymmetric time-dependent electric field to sort ions not by mobility itself, but by the difference between its values in strong and weak electric fields. Coupling of FAIMS to conventional IMS and stacking of conventional IMS stages have enabled two-dimensional separations that dramatically expand the power of ion mobility methods.

  12. Mobile Biomass Pelletizing System

    SciTech Connect (OSTI)

    Thomas Mason

    2009-04-16

    This grant project examines multiple aspects of the pelletizing process to determine the feasibility of pelletizing biomass using a mobile form factor system. These aspects are: the automatic adjustment of the die height in a rotary-style pellet mill, the construction of the die head to allow the use of ceramic materials for extreme wear, integrating a heat exchanger network into the entire process from drying to cooling, the use of superheated steam for adjusting the moisture content to optimum, the economics of using diesel power to operate the system; a break-even analysis of estimated fixed operating costs vs. tons per hour capacity. Initial development work has created a viable mechanical model. The overall analysis of this model suggests that pelletizing can be economically done using a mobile platform.

  13. Environmental Technology Verification of Mobile Sources Control...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Environmental Technology Verification of Mobile Sources Control Technologies Environmental Technology Verification of Mobile Sources Control Technologies 2005 Diesel Engine...

  14. Tandem photovoltaic cells with a composite intermediate layer

    SciTech Connect (OSTI)

    Travkin, V. V. Pakhomov, G. L.; Luk’anov, A. Yu.; Stuzhin, P. A.

    2015-11-15

    We have fabricated and tested tandem photovoltaic cells containing series-connected subcells of the “oxide–organic semiconductor–metal” type. The organic semiconductors were two phthalocyanine dyes (SubPc and PcVO); Al or Ag:Mg were used as capping metallic electrodes. A semitransparent composite metal–oxide layer formed by molybdenum oxide MoO{sub x} deposited over an ultrathin Al layer is used to join the subcells. Additionally, a MoO{sub x} layer deposited onto glass/ITO substrates serves as an anode buffer in the front subcell, and LiF deposited onto the dye layers serves as a cathode buffer in the front or rear subcells. Upon optimization of the thickness and composition of the intermediate layer, the open circuit voltage U{sub oc} amounts to 1.6 V reflecting total summation of the contributions from the each of the subcells at a wide spectral coating from 300–1000 nm. The fill factor in the tandem cell is not worse than in individually made single cells with the same scheme or in disconnected subcells.

  15. Securing mobile code.

    SciTech Connect (OSTI)

    Link, Hamilton E.; Schroeppel, Richard Crabtree; Neumann, William Douglas; Campbell, Philip LaRoche; Beaver, Cheryl Lynn; Pierson, Lyndon George; Anderson, William Erik

    2004-10-01

    If software is designed so that the software can issue functions that will move that software from one computing platform to another, then the software is said to be 'mobile'. There are two general areas of security problems associated with mobile code. The 'secure host' problem involves protecting the host from malicious mobile code. The 'secure mobile code' problem, on the other hand, involves protecting the code from malicious hosts. This report focuses on the latter problem. We have found three distinct camps of opinions regarding how to secure mobile code. There are those who believe special distributed hardware is necessary, those who believe special distributed software is necessary, and those who believe neither is necessary. We examine all three camps, with a focus on the third. In the distributed software camp we examine some commonly proposed techniques including Java, D'Agents and Flask. For the specialized hardware camp, we propose a cryptographic technique for 'tamper-proofing' code over a large portion of the software/hardware life cycle by careful modification of current architectures. This method culminates by decrypting/authenticating each instruction within a physically protected CPU, thereby protecting against subversion by malicious code. Our main focus is on the camp that believes that neither specialized software nor hardware is necessary. We concentrate on methods of code obfuscation to render an entire program or a data segment on which a program depends incomprehensible. The hope is to prevent or at least slow down reverse engineering efforts and to prevent goal-oriented attacks on the software and execution. The field of obfuscation is still in a state of development with the central problem being the lack of a basis for evaluating the protection schemes. We give a brief introduction to some of the main ideas in the field, followed by an in depth analysis of a technique called 'white-boxing'. We put forth some new attacks and improvements

  16. ASSESSMENT OF MARKER PROTEINS IDENTIFIED IN WHOLE CELL EXTRACTS FOR BACTERIAL SPECIATION USING LIQUID CHROMATOGRAPHY ELECTROSPRAY IONIZATION TANDEM MASS SPECTROMETRY

    SciTech Connect (OSTI)

    Kooken, Jennifer M.; Fox, Karen F.; Fox, Alvin; Wunschel, David S.

    2014-02-02

    ASSESSMENT OF MARKER PROTEINS IDENTIFIED IN WHOLE CELL EXTRACTS FOR BACTERIAL SPECIATION USING LIQUID CHROMATOGRAPHY ELECTROSPRAY IONIZATION TANDEM MASS SPECTROMETRY

  17. Benefits of Using Mobile Transformers and Mobile Substations...

    Energy Savers [EERE]

    and mobile substations (MTS) to rapidly restore electrical service to areas subjected to blackouts as a result of equipment failure, natural disasters, acts of terrorism, or war. ...

  18. Status of High Performance PV: Polycrystalline Thin-Film Tandems

    SciTech Connect (OSTI)

    Symko-Davies, M.

    2005-02-01

    The High-Performance Photovoltaic (HiPerf PV) Project was initiated by the U.S. Department of Energy to substantially increase the viability of photovoltaics (PV) for cost-competitive applications so that PV can contribute significantly to our energy supply and our environment. The HiPerf PV Project aims at exploring the ultimate performance limits of existing PV technologies, approximately doubling their sunlight-to-electricity conversion efficiencies during its course. This work includes bringing thin-film cells and modules toward 25% and 20% efficiencies, respectively, and developing multijunction concentrator cells and modules able to convert more than one-third of the sun's energy to electricity (i.e., 33% efficiency). This paper will address recent accomplishments of the NREL in-house research effort involving polycrystalline thin-film tandems, as well as the research efforts under way in the subcontracted area.

  19. Synfuels from fusion: producing hydrogen with the Tandem Mirror Reactor and thermochemical cycles

    SciTech Connect (OSTI)

    Werner, R.W.; Ribe, F.L.

    1981-01-21

    This volume contains the following sections: (1) the Tandem Mirror fusion driver, (2) the Cauldron blanket module, (3) the flowing microsphere, (4) coupling the reactor to the process, (5) the thermochemical cycles, and (6) chemical reactors and process units. (MOW)

  20. Semi-transparent perovskite solar cells for tandems with silicon and CIGS

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Bailie, Colin D.; Christoforo, M. Greyson; Mailoa, Jonathan P.; Bowring, Andrea R.; Unger, Eva L.; Nguyen, William H.; Burschka, Julian; Pellet, Norman; Lee, Jungwoo Z.; Grätzel, Michael; et al

    2014-12-23

    A promising approach for upgrading the performance of an established low-bandgap solar technology without adding much cost is to deposit a high bandgap polycrystalline semiconductor on top to make a tandem solar cell. We use a transparent silver nanowire electrode on perovskite solar cells to achieve a semi-transparent device. We place the semi-transparent cell in a mechanically-stacked tandem configuration onto copper indium gallium diselenide (CIGS) and low-quality multicrystalline silicon (Si) to achieve solid-state polycrystalline tandem solar cells with a net improvement in efficiency over the bottom cell alone. Furthermore, this work paves the way for integrating perovskites into a low-costmore » and high-efficiency (>25%) tandem cell.« less

  1. Semi-transparent perovskite solar cells for tandems with silicon and CIGS

    SciTech Connect (OSTI)

    Bailie, Colin D.; Christoforo, M. Greyson; Mailoa, Jonathan P.; Bowring, Andrea R.; Unger, Eva L.; Nguyen, William H.; Burschka, Julian; Pellet, Norman; Lee, Jungwoo Z.; Grätzel, Michael; Noufi, Rommel; Buonassisi, Tonio; Salleo, Alberto; McGehee, Michael D.

    2014-12-23

    A promising approach for upgrading the performance of an established low-bandgap solar technology without adding much cost is to deposit a high bandgap polycrystalline semiconductor on top to make a tandem solar cell. We use a transparent silver nanowire electrode on perovskite solar cells to achieve a semi-transparent device. We place the semi-transparent cell in a mechanically-stacked tandem configuration onto copper indium gallium diselenide (CIGS) and low-quality multicrystalline silicon (Si) to achieve solid-state polycrystalline tandem solar cells with a net improvement in efficiency over the bottom cell alone. Furthermore, this work paves the way for integrating perovskites into a low-cost and high-efficiency (>25%) tandem cell.

  2. GaP/Silicon Tandem Solar Cell with Extended Temperature Range - Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Innovation Portal Vehicles and Fuels Vehicles and Fuels Solar Photovoltaic Solar Photovoltaic Find More Like This Return to Search GaP/Silicon Tandem Solar Cell with Extended Temperature Range NASA Glenn Research Center (http://www.nasa.gov/centers/glenn/home/index.html) National Aeronautics and Space Administration Contact NASA About This Technology Technology Marketing SummaryNASA Glenn Research Center (GRC) innovators have developed unique, tandem photovoltaic cells (or "solar

  3. Photo of the Week: Inside the Tandem Mirror Experiment | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Tandem Mirror Experiment Photo of the Week: Inside the Tandem Mirror Experiment December 28, 2012 - 2:22pm Addthis This 1978 photo shows two workers inside the Mirror Fusion Test Facility, a magnetic confinement fusion device designed and built at Lawrence Livermore National Laboratory. In this experiment, magnetic mirrors are placed at both ends of a central magnetic tube. Very hot and dense plasmas inside each mirror enhanced the confinement of another plasma inside the central

  4. Argonne Tandem Linac Accelerator System (ATLAS) | U.S. DOE Office of

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Science (SC) Argonne Tandem Linac Accelerator System (ATLAS) Nuclear Physics (NP) NP Home About Research Facilities User Facilities Argonne Tandem Linac Accelerator System (ATLAS) Continuous Electron Beam Accelerator Facility (CEBAF) Relativistic Heavy Ion Collider (RHIC) Project Development Isotope Program Facilities Science Highlights Benefits of NP Funding Opportunities Nuclear Science Advisory Committee (NSAC) Community Resources Contact Information Nuclear Physics U.S. Department of

  5. Michigan, Missouri: Innovative Mobile Exhibits Bring Electric...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Michigan, Missouri: Innovative Mobile Exhibits Bring Electric Vehicles to Students and Public Michigan, Missouri: Innovative Mobile Exhibits Bring Electric Vehicles to Students and...

  6. Improving Data Mobility & Management for International Cosmology...

    Office of Scientific and Technical Information (OSTI)

    Improving Data Mobility & Management for International Cosmology Citation Details In-Document Search Title: Improving Data Mobility & Management for International Cosmology In February ...

  7. Automatic Differentiation Package

    Energy Science and Technology Software Center (OSTI)

    2007-03-01

    Sacado is an automatic differentiation package for C++ codes using operator overloading and C++ templating. Sacado provide forward, reverse, and Taylor polynomial automatic differentiation classes and utilities for incorporating these classes into C++ codes. Users can compute derivatives of computations arising in engineering and scientific applications, including nonlinear equation solving, time integration, sensitivity analysis, stability analysis, optimization and uncertainity quantification.

  8. Laser processing technique for fabricating series-connected and tandem junction series-connected solar cells into a solar battery

    DOE Patents [OSTI]

    Hanak, Joseph J.

    1981-01-01

    A method of fabricating series-connected and tandem junction series-connected solar cells into a solar battery with laser scribing.

  9. Thin Film Si Bottom Cells for Tandem Device Structures: Final Technical Report, 15 December 2003 - 15 October 2007

    SciTech Connect (OSTI)

    Yelundur, V.; Hegedus, S.; Rohatgi, A.; Birkmire, R.

    2008-11-01

    GIT and IEC developed thin-film Si bottom cell and showed that deposition of top cell in tandem device did not reduce bottom cell performance.

  10. Equivalent circuit analysis of radiative coupling in monolithic tandem solar cells

    SciTech Connect (OSTI)

    Lan, Dongchen E-mail: d.lan@unswalumni.com; Green, Martin A.

    2015-06-29

    As solar cell efficiency improves towards the Shockley-Queisser limit, so does the radiative efficiency of the cell. For tandem stacks of cells where energy conversion efficiency now exceeds 46%, radiative coupling between the cells is becoming increasingly important to consider in cell design, measurement, and performance prediction. We show how an equivalent circuit model can capture the complex radiative interactions between cells in such tandem stacks, allowing more insight into the impact on cell performance. The circuit's use is demonstrated by deriving results relevant to the critical step of eliminating coupling effects from measured cell spectral responses.

  11. Mobile Alternative Fueling Station Locator

    SciTech Connect (OSTI)

    Not Available

    2009-04-01

    The Department of Energy's Alternative Fueling Station Locator is available on-the-go via cell phones, BlackBerrys, or other personal handheld devices. The mobile locator allows users to find the five closest biodiesel, electricity, E85, hydrogen, natural gas, and propane fueling sites using Google technology.

  12. NERSC Releases Mobile Apps to Users

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Releases Mobile Apps to Users NERSC Releases Mobile Apps to Users Job Status, MOTD and Pilot of VASP Submission Available with More to Come April 23, 2012 In an effort to make...

  13. High explosives vapor detection by atmospheric sampling glow discharge ionization/tandem mass spectrometry

    SciTech Connect (OSTI)

    McLuckey, S.A.; Goeringer, D.E.; Asano, K.G.

    1996-02-01

    The combination of atmospheric sampling glow discharge ionization with tandem mass spectrometry for the detection of traces of high explosives is described. Particular emphasis is placed on use of the quadrupole ion trap as the type of tandem mass spectrometer. Atmospheric sampling glow discharge provides a simple, rugged, and efficient means for anion formation while the quadrupole ion trap provides for efficient tandem mass spectrometry. Mass selective ion accumulation and non-specific ion activation methods can be used to overcome deleterious effects arising from ion/ion interactions. Such interactions constitute the major potential technical barrier to the use of the ion trap for real-time monitoring of targeted compounds in uncontrolled and highly variable matrices. Tailored waveforms can be used to effect both mass selective ion accumulation and ion activation. Concatenated tailored waveforms allow for both functions in a single experiment thereby providing the capability for monitoring several targeted species simultaneously. The combination of atmospheric sampling glow discharge ionization with a state-of-the-art analytical quadrupole ion trap is a highly sensitive and specific detector for traces of high explosives. The combination is also small and inexpensive relative to virtually any other form of tandem mass spectrometry. The science and technology underlying the glow discharge/ion trap combination is sufficiently mature to form the basis for an engineering effort to make the detector portable. 85 refs.

  14. Production of Ar{sup q+} ions with a tandem linear Paul trap

    SciTech Connect (OSTI)

    Higaki, H. Nagayasu, K.; Iwai, T.; Ito, K.; Okamoto, H.

    2015-06-29

    A tandem linear Paul trap was used to create highly charged Argon ions by electron impact ionizations. By improving the operation scheme, the production of Ar{sup 4+} ions was confirmed. Possible improvements for the future experiments with laser cooled Ca{sup +} ions are suggested.

  15. Nuclear breeder reactor fuel element with axial tandem stacking and getter

    DOE Patents [OSTI]

    Gibby, Ronald L.; Lawrence, Leo A.; Woodley, Robert E.; Wilson, Charles N.; Weber, Edward T.; Johnson, Carl E.

    1981-01-01

    A breeder reactor fuel element having a tandem arrangement of fissile and fertile fuel with a getter for fission product cesium disposed between the fissile and fertile sections. The getter is effective at reactor operating temperatures to isolate the cesium generated by the fissile material from reacting with the fertile fuel section.

  16. The mobile phase in coals: Its nature and modes of release: Part 2, Efforts to better define the nature and magnitude of the mobile phase: Final report

    SciTech Connect (OSTI)

    Given, P.H.

    1987-04-01

    Several liquefaction conditions and many extracting solvents were used in attempts to set up conditions such that, as the conditions became more severe, progressively more hexane-solubles, analyzable by GC/MS, would be released. It was hoped to identify a threshold beyond which trapped mobile phase molecules would become evident. A set of 10 hexane-soluble fractions, all obtained under various conditions from the same coal (a sample of Herrin No. 6 seam, Illinois), were subjected to analysis by tandem mass spectrometry (MS/MS). Yields ranged from 0.6 to 16% of the organic matter in the coal. Prominent constituents of all of the fractions were homologous series of alkyl aromatic hydrocarbons, phenols and heterocycles, notably alkylacenaphthenes. Alkyl chains were either unbranched or lightly branched. There was a similarity in the spectra of all of the fractions irrespective of yield. The ease with which a certain homologous series can be released from a coal is highly variable. Thus the data are consistent with the concept of a mobile phase some components of which are trapped in cavities with entrances and exits of restricted size. Release of the various physically held species and the fragments from thermal breakdown of the structure will certainly present a very complex system for kinetic modeling. 30 refs., 10 tabs.

  17. Structure of a Longitudinal Actin Dimer Assembled by Tandem W Domains: Implications for Actin Filament Nucleation

    SciTech Connect (OSTI)

    Rebowski, Grzegorz; Namgoong, Suk; Boczkowska, Malgorzata; Leavis, Paul C.; Navaza, Jorge; Dominguez, Roberto

    2013-11-20

    Actin filament nucleators initiate polymerization in cells in a regulated manner. A common architecture among these molecules consists of tandem WASP homology 2 domains (W domains) that recruit three to four actin subunits to form a polymerization nucleus. We describe a low-resolution crystal structure of an actin dimer assembled by tandem W domains, where the first W domain is cross-linked to Cys374 of the actin subunit bound to it, whereas the last W domain is followed by the C-terminal pointed end-capping helix of thymosin {beta}4. While the arrangement of actin subunits in the dimer resembles that of a long-pitch helix of the actin filament, important differences are observed. These differences result from steric hindrance of the W domain with intersubunit contacts in the actin filament. We also determined the structure of the first W domain of Vibrio parahaemolyticus VopL cross-linked to actin Cys374 and show it to be nearly identical with non-cross-linked W-Actin structures. This result validates the use of cross-linking as a tool for the study of actin nucleation complexes, whose natural tendency to polymerize interferes with most structural methods. Combined with a biochemical analysis of nucleation, the structures may explain why nucleators based on tandem W domains with short inter-W linkers have relatively weak activity, cannot stay bound to filaments after nucleation, and are unlikely to influence filament elongation. The findings may also explain why nucleation-promoting factors of the Arp2/3 complex, which are related to tandem-W-domain nucleators, are ejected from branch junctions after nucleation. We finally show that the simple addition of the C-terminal pointed end-capping helix of thymosin {beta}4 to tandem W domains can change their activity from actin filament nucleation to monomer sequestration.

  18. ARM - Datastreams - tdmahyg

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    from you Send us a note below or call us at 1-888-ARM-DATA. Send Datastream : TDMAHYG Tandem Differential Mobility Analyzer: hygroscopic growth rates Active Dates 2005.10.07 -...

  19. ARM - Instrument - htdma

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    you Send us a note below or call us at 1-888-ARM-DATA. Send Instrument : Humidified Tandem Differential Mobility Analyzer (HTDMA) Instrument Categories Aerosols This instrument...

  20. ARM - Instrument - tdma

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to hear from you Send us a note below or call us at 1-888-ARM-DATA. Send Instrument : Tandem Differential Mobility Analyzer (TDMA) Instrument Categories Aerosols Picture of the...

  1. ARM - VAP Product - tdmaccncoll

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    you Send us a note below or call us at 1-888-ARM-DATA. Send VAP Output : TDMACCNCOLL Tandem Differential Mobility Analyzer: Cloud Condensation Nuclei -- D. Collins Active Dates...

  2. ARM - Campaign Instrument - tdma-air

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    you Send us a note below or call us at 1-888-ARM-DATA. Send Campaign Instrument : Tandem Differential Mobility Analyzer- Airborne (TDMA-AIR) Instrument Categories Aerosols,...

  3. ARM - Datastreams - tdmasize

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    you Send us a note below or call us at 1-888-ARM-DATA. Send Datastream : TDMASIZE Tandem Differential Mobility Analyzer: size-resolved concentrations Active Dates 2005.10.07 -...

  4. ARM - Campaign Instrument - tdma

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    would love to hear from you Send us a note below or call us at 1-888-ARM-DATA. Send Campaign Instrument : Tandem Differential Mobility Analyzer (TDMA) Instrument Categories...

  5. Mobile phone and my health

    SciTech Connect (OSTI)

    Surducan, Aneta; Dabala, Dana; Neamtu, Camelia Surducan, Vasile Surducan, Emanoil

    2013-11-13

    The interaction of the microwave radiation emitted by mobile phones with the user's body is analyzed from the International Commission on Non-Ionizing Radiation Protection (ICNIRP) recommendations perspective as a correlation between the specific absorption ratio (SAR) of the mobile phone and the call duration. The relative position of the cell phone to the user's body, the dielectric properties of the exposed body parts, the SAR value and the call duration are considered in the local body temperature rise due to the microwave heating effect. The recommended local temperature rise limit in the human body is evaluated according to standards. The aim of this study is to disseminate information to young people, especially high school students, about the microwave thermal effects on the human body, to make them aware of the environmental electromagnetic pollution and to offer them a simple method of biological self protection.

  6. Differential comparator cirucit

    DOE Patents [OSTI]

    Hickling, Ronald M.

    1996-01-01

    A differential comparator circuit for an Analog-to-Digital Converter (ADC) or other application includes a plurality of differential comparators and a plurality of offset voltage generators. Each comparator includes first and second differentially connected transistor pairs having equal and opposite voltage offsets. First and second offset control transistors are connected in series with the transistor pairs respectively. The offset voltage generators generate offset voltages corresponding to reference voltages which are compared with a differential input voltage by the comparators. Each offset voltage is applied to the offset control transistors of at least one comparator to set the overall voltage offset of the comparator to a value corresponding to the respective reference voltage. The number of offset voltage generators required in an ADC application can be reduced by a factor of approximately two by applying the offset voltage from each offset voltage generator to two comparators with opposite logical sense such that positive and negative offset voltages are produced by each offset voltage generator.

  7. ARM - ARM Mobile Facility 1 Article

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CenterARM Mobile Facility 1ARM Mobile Facility 1 Article Media Contact Hanna Goss hanna-dot-goss-at-pnnl-dot-gov @armnewsteam Field Notes Blog Topics Field Notes117 AGU 3 AMIE 10 ARM Aerial Facility 2 ARM Mobile Facility 1 7 ARM Mobile Facility 2 47 ARM Mobile Facility 3 1 BAECC 1 BBOP 4 CARES 1 Data Quality Office 2 ENA 2 GOAMAZON 7 HI-SCALE 4 LASIC 3 MAGIC 15 MC3E 17 PECAN 3 SGP 8 STORMVEX 29 TCAP 3 Search News Search Blog News Center All Categories What's this? Social Media Guidance News

  8. Guarded Motion for Mobile Robots

    Energy Science and Technology Software Center (OSTI)

    2005-03-30

    The Idaho National Laboratory (INL) has created codes that ensure that a robot will come to a stop at a precise, specified distance from any obstacle regardless of the robot's initial speed, its physical characteristics, and the responsiveness of the low-level motor control schema. This Guarded Motion for Mobile Robots system iteratively adjusts the robot's action in response to information about the robot's environment.

  9. Differential homogeneous immunosensor device

    DOE Patents [OSTI]

    Malmros, Mark K.; Gulbinski, III, Julian

    1990-04-10

    There is provided a novel method of testing for the presence of an analyte in a fluid suspected of containing the same. In this method, in the presence of the analyte, a substance capable of modifying certain characteristics of the substrate is bound to the substrate and the change in these qualities is measured. While the method may be modified for carrying out quantitative differential analyses, it eliminates the need for washing analyte from the substrate which is characteristic of prior art methods.

  10. SIMULTANEOUS DIFFERENTIAL EQUATION COMPUTER

    DOE Patents [OSTI]

    Collier, D.M.; Meeks, L.A.; Palmer, J.P.

    1960-05-10

    A description is given for an electronic simulator for a system of simultaneous differential equations, including nonlinear equations. As a specific example, a homogeneous nuclear reactor system including a reactor fluid, heat exchanger, and a steam boiler may be simulated, with the nonlinearity resulting from a consideration of temperature effects taken into account. The simulator includes three operational amplifiers, a multiplier, appropriate potential sources, and interconnecting R-C networks.

  11. Temperature differential detection device

    DOE Patents [OSTI]

    Girling, Peter M.

    1986-01-01

    A temperature differential detection device for detecting the temperature differential between predetermined portions of a container wall is disclosed as comprising a Wheatstone bridge circuit for detecting resistance imbalance with a first circuit branch having a first elongated wire element mounted in thermal contact with a predetermined portion of the container wall, a second circuit branch having a second elongated wire element mounted in thermal contact with a second predetermined portion of a container wall with the wire elements having a predetermined temperature-resistant coefficient, an indicator interconnected between the first and second branches remote from the container wall for detecting and indicating resistance imbalance between the first and second wire elements, and connector leads for electrically connecting the wire elements to the remote indicator in order to maintain the respective resistance value relationship between the first and second wire elements. The indicator is calibrated to indicate the detected resistance imbalance in terms of a temperature differential between the first and second wall portions.

  12. Temperature differential detection device

    DOE Patents [OSTI]

    Girling, P.M.

    1986-04-22

    A temperature differential detection device for detecting the temperature differential between predetermined portions of a container wall is disclosed as comprising a Wheatstone bridge circuit for detecting resistance imbalance with a first circuit branch having a first elongated wire element mounted in thermal contact with a predetermined portion of the container wall, a second circuit branch having a second elongated wire element mounted in thermal contact with a second predetermined portion of a container wall with the wire elements having a predetermined temperature-resistant coefficient, an indicator interconnected between the first and second branches remote from the container wall for detecting and indicating resistance imbalance between the first and second wire elements, and connector leads for electrically connecting the wire elements to the remote indicator in order to maintain the respective resistance value relationship between the first and second wire elements. The indicator is calibrated to indicate the detected resistance imbalance in terms of a temperature differential between the first and second wall portions. 2 figs.

  13. Differential transimpedance amplifier circuit for correlated differential amplification

    DOE Patents [OSTI]

    Gresham, Christopher A.; Denton, M. Bonner; Sperline, Roger P.

    2008-07-22

    A differential transimpedance amplifier circuit for correlated differential amplification. The amplifier circuit increase electronic signal-to-noise ratios in charge detection circuits designed for the detection of very small quantities of electrical charge and/or very weak electromagnetic waves. A differential, integrating capacitive transimpedance amplifier integrated circuit comprising capacitor feedback loops performs time-correlated subtraction of noise.

  14. Sputtered II-VI Alloys and Structures forTandem PV: Final Subcontract Report, 9 December 2003 - 30 July 2007

    SciTech Connect (OSTI)

    Compaan, A. D.; Collins, R.; Karpov, V. G.; Giolando, D.

    2008-09-01

    This report elaborates on Phase 3 and provides summaries of the first two Phases. Phase 3 research work was divided into five task areas covering different aspects of the II-VI tandem cell.

  15. Charged particle mobility refrigerant analyzer

    DOE Patents [OSTI]

    Allman, S.L.; Chunghsuan Chen; Chen, F.C.

    1993-02-02

    A method for analyzing a gaseous electronegative species comprises the steps of providing an analysis chamber; providing an electric field of known potential within the analysis chamber; admitting into the analysis chamber a gaseous sample containing the gaseous electronegative species; providing a pulse of free electrons within the electric field so that the pulse of free electrons interacts with the gaseous electronegative species so that a swarm of electrically charged particles is produced within the electric field; and, measuring the mobility of the electrically charged particles within the electric field.

  16. Mechanical accessories for mobile teleoperators

    SciTech Connect (OSTI)

    Feldman, M.J.; Herndon, J.N.

    1985-01-01

    The choice of optimum mechanical accessories for mobile teleoperators involves matching the criteria for emergency response with the available technology. This paper presents a general background to teleoperations, a potpourri of the manipulator systems available, and an argument for force reflecting manipulation. The theme presented is that the accomplishment of humanlike endeavors in hostile environments will be most successful when man model capabilities are utilized. The application of recent electronic technology to manipulator development has made new tools available to be applied to emergency response activities. The development activities described are products of the Consolidated Fuel Reprocessing Program at the Oak Ridge National Laboratory. 13 refs., 7 figs.

  17. Progress towards a 30% efficient GaInP/Si tandem solar cells

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Essig, Stephanie; Ward, Scott; Steiner, Myles A.; Friedman, Daniel J.; Geisz, John F.; Stradins, Paul; Young, David L.

    2015-08-28

    The performance of dual-junction solar cells with a Si bottom cell has been investigated both theoretically and experimentally. Simulations show that adding a top junction with an energy bandgap of 1.6 -1.9 eV to a standard silicon solar cell enables efficiencies over 38%. Currently, top junctions of GaInP (1.8 eV) are the most promising as they can achieve 1-sun efficiencies of 20.8% [1]. We fabricated mechanically stacked, four terminal GaInP/Si tandem solar cells using a transparent adhesive between the subcells. These tandem devices achieved an efficiency of 27% under AM1.5 g spectral conditions. Furthermore, higher efficiencies can be achieved bymore » using an improved Si-bottom cell and by optimizing the dual-junction device for long-wavelength light and luminescent coupling between the two junctions.« less

  18. Progress towards a 30% efficient GaInP/Si tandem solar cells

    SciTech Connect (OSTI)

    Essig, Stephanie; Ward, Scott; Steiner, Myles A.; Friedman, Daniel J.; Geisz, John F.; Stradins, Paul; Young, David L.

    2015-08-28

    The performance of dual-junction solar cells with a Si bottom cell has been investigated both theoretically and experimentally. Simulations show that adding a top junction with an energy bandgap of 1.6 -1.9 eV to a standard silicon solar cell enables efficiencies over 38%. Currently, top junctions of GaInP (1.8 eV) are the most promising as they can achieve 1-sun efficiencies of 20.8% [1]. We fabricated mechanically stacked, four terminal GaInP/Si tandem solar cells using a transparent adhesive between the subcells. These tandem devices achieved an efficiency of 27% under AM1.5 g spectral conditions. Furthermore, higher efficiencies can be achieved by using an improved Si-bottom cell and by optimizing the dual-junction device for long-wavelength light and luminescent coupling between the two junctions.

  19. Development of Highly-Efficient GaInP/Si Tandem Solar Cells

    SciTech Connect (OSTI)

    Essig, Stephanie; Geisz, John F.; Steiner, Myles A.; Merkle, Agnes; Peibst, Robby; Schmidt, Jan; Brendel, Rolf; Ward, Scott; Friedman, Daniel J.; Stradins, Paul; Young, David L.

    2015-06-14

    Dual-junction solar cells consisting of rear-heterojunction GaInP top cells and back-junction, back-contacted crystalline Si bottom cells were fabricated and characterized. Our calculations show that theoretical efficiencies up to 38.9% can be achieved with Si-based tandem devices. In our experiments, the two subcells were fabricated separately and stacked with an index matching fluid. In contrast to conventional mechanically stacked solar cells, that contain two metal grids at the interface, our concept includes a fully back contacted bottom cell which reduces the shadow losses in the device. A 1-sun AM1.5g cumulative efficiency of (26.2 +/- 0.6)% has been achieved with this novel GaInP/Si 4-terminal tandem solar cell.

  20. Polymer Solar Cells: New Materials, 3D Morphology, and Tandem Devices |

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MIT-Harvard Center for Excitonics Polymer Solar Cells: New Materials, 3D Morphology, and Tandem Devices March 2, 2010 at 3pm/36-428 René Janssen Molecular Materials and Nanosystems, Eindhoven University of Technology ReneJanssen2-small_000 abstract: Polymer solar cells offer an opportunity for low-cost, large area renewable energy production. These devices use a phase separated blend of two organic semiconductors with energy levels that lead to intermolecular charge transfer after

  1. Synfuels from fusion: using the tandem mirror reactor and a thermochemical cycle to produce hydrogen

    SciTech Connect (OSTI)

    Werner, R.W.

    1982-11-01

    This study is concerned with the following area: (1) the tandem mirror reactor and its physics; (2) energy balance; (3) the lithium oxide canister blanket system; (4) high-temperature blanket; (5) energy transport system-reactor to process; (6) thermochemical hydrogen processes; (7) interfacing the GA cycle; (8) matching power and temperature demands; (9) preliminary cost estimates; (10) synfuels beyond hydrogen; and (11) thermodynamics of the H/sub 2/SO/sub 4/-H/sub 2/O system. (MOW)

  2. High-efficiency, monolithic, multi-bandgap, tandem photovoltaic energy converters

    DOE Patents [OSTI]

    Wanlass, Mark W.

    2011-11-29

    A monolithic, multi-bandgap, tandem solar photovoltaic converter has at least one, and preferably at least two, subcells grown lattice-matched on a substrate with a bandgap in medium to high energy portions of the solar spectrum and at least one subcell grown lattice-mismatched to the substrate with a bandgap in the low energy portion of the solar spectrum, for example, about 1 eV.

  3. High-efficiency, monolithic, multi-bandgap, tandem, photovoltaic energy converters

    DOE Patents [OSTI]

    Wanlass, Mark W

    2014-05-27

    A monolithic, multi-bandgap, tandem solar photovoltaic converter has at least one, and preferably at least two, subcells grown lattice-matched on a substrate with a bandgap in medium to high energy portions of the solar spectrum and at least one subcell grown lattice-mismatched to the substrate with a bandgap in the low energy portion of the solar spectrum, for example, about 1 eV.

  4. NREL: Transportation Research - Sustainable Mobility Initiative

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mobility Initiative Graphic of four concentric circles starting with the traveler and branching out to encompass the vehicle, transport system, and built environment. NREL's Sustainable Mobility Initiative approaches sustainable transportation as a network of travelers, services, and environments-rather than just vehicles and roads-using connectivity and automation to optimize mobility and significantly reduce related energy consumption. This concept of an intelligent, integrated, and dynamic

  5. Environmental Technology Verification of Mobile Sources Control

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technologies | Department of Energy Environmental Technology Verification of Mobile Sources Control Technologies Environmental Technology Verification of Mobile Sources Control Technologies 2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations and Posters 2005_deer_elion.pdf (158.94 KB) More Documents & Publications EPA Mobile Source Rule Update Efficient Use of Natural Gas Based Fuels in Heavy-Duty Engines The California Demonstration Program for Control of PM from

  6. GaInP/GaAs/GaInAs Monolithic Tandem Cells for High-Performance Solar Concentrators

    SciTech Connect (OSTI)

    Wanlass, M. W.; Ahrenkiel, S. P.; Albin, D. S.; Carapella, J. J.; Duda, A.; Emery, K.; Geisz, J. F.; Jones, K.; Kurtz, S.; Moriarty, T.; Romero, M. J.

    2005-08-01

    We present a new approach for ultra-high-performance tandem solar cells that involves inverted epitaxial growth and ultra-thin device processing. The additional degree of freedom afforded by the inverted design allows the monolithic integration of high-, and medium-bandgap, lattice-matched (LM) subcell materials with lower-bandgap, lattice-mismatched (LMM) materials in a tandem structure through the use of transparent compositionally graded layers. The current work concerns an inverted, series-connected, triple-bandgap, GaInP (LM, 1.87 eV)/GaAs (LM, 1.42 eV)/GaInAs (LMM, {approx}1 eV) device structure grown on a GaAs substrate. Ultra-thin tandem devices are fabricated by mounting the epiwafers to pre-metallized Si wafer handles and selectively removing the parent GaAs substrate. The resulting handle-mounted, ultra-thin tandem cells have a number of important advantages, including improved performance and potential reclamation/reuse of the parent substrate for epitaxial growth. Additionally, realistic performance modeling calculations suggest that terrestrial concentrator efficiencies in the range of 40-45% are possible with this new tandem cell approach. A laboratory-scale (0.24 cm2), prototype GaInP/GaAs/GaInAs tandem cell with a terrestrial concentrator efficiency of 37.9% at a low concentration ratio (10.1 suns) is described, which surpasses the previous world efficiency record of 37.3%.

  7. High-Efficiency GaInP/GaAs Tandem Solar Cells

    SciTech Connect (OSTI)

    Bertness, K. A.; Friedman, D. J.; Kurtz, S. R.; Kibbler, A. E.; Cramer, C.; Olson, J. M.

    1996-09-01

    GaInP/GaAs tandem solar cells have achieved efficiencies between 25.7-30.2%, depending on illumination conditions. The efficiencies are the highest confirmed two-terminal values measured for any solar cell within each standard illumination category. The monolithic, series-connected design of the tandem cells allows them to be substituted for silicon or gallium arsenide cells in photovoltaic panel systems with minimal design changes. The advantages of using GaInP/GaAs tandem solar cells in space and terrestrial applications are discussed primarily in terms of the reduction in balance-of-system costs that accrues when using a higher efficiency cell. The new efficiency values represent a significant improvement over previous efficiencies for this materials system, and we identify grid design, back interface passivation, and top interface passivation as the three key factors leading to this improvement. In producing the high-efficiency cells, we have addressed nondestructive diagnostics and materials growth reproducibility as well as peak cell performance.

  8. High-efficiency GaInP/GaAs tandem solar cells

    SciTech Connect (OSTI)

    Bertness, K.A.; Friedman, D.J.; Kurtz, S.R.; Kibbler, A.E.; Kramer, C.; Olson, J.M.

    1994-12-01

    GaInP/GaAs tandem solar cells have achieved new record efficiencies, specifically 25.7% under air-mass 0 (AM0) illumination, 29.5% under AM 1.5 global (AM1.5G) illumination, and 30.2% at 140-180x concentration under AM 1.5 direct (AM1.5D) illumination. These values are the highest two-terminal efficiencies achieved by any solar cell under these illumination conditions. The monolithic, series-connected design of the tandem cells allows them to be substituted for silicon or gallium arsenide cells in photovoltaic panel systems with minimal design changes. The advantages of using GaInP/GaAs tandem solar cells in space and terrestrial applications are discussed primarily in terms of the reduction in balance-of-system costs that accrues when using a higher efficiency cell. The new efficiency values represent a significant improvement over previous efficiencies for this materials system, and we identify grid design, back interface passivation, and top interface passivation as the three key factors leading to this improvement. In producing the high-efficiency cells, we have addressed nondestructive diagnostics and materials growth reproducibility as well as peak cell performance. 31 refs.

  9. Heavy Mobile Equipment Mechanic (One Mechanic Shop)

    Broader source: Energy.gov [DOE]

    Join the Bonneville Power Administration (BPA) for a challenging and rewarding career, while working, living, and playing in the Pacific Northwest. The Heavy Mobile Equipment Mechanic (One Mechanic...

  10. Mobile Power Solutions | Open Energy Information

    Open Energy Info (EERE)

    laboratory focused on United NationsDepartment of Transportation compliance and battery performance testing. References: Mobile Power Solutions1 This article is a stub....

  11. Heavy Mobile Equipment Mechanic (1 Mechanic Shop)

    Broader source: Energy.gov [DOE]

    A successful candidate will perform preventative, predictive, and corrective maintenance on Bonneville Power Administration (BPA's) light and heavy mobile equipment in maintenance and filed...

  12. Clean Mobile AG | Open Energy Information

    Open Energy Info (EERE)

    AG Place: Munich, Bavaria, Germany Sector: Vehicles Product: Manufacturer of fuel cell-powered drives for small vehicles. References: Clean Mobile AG1 This article is a...

  13. Mobile Business Innovation Center | Open Energy Information

    Open Energy Info (EERE)

    Innovation Center Jump to: navigation, search Name: Mobile Business Innovation Center Place: United States Product: Government & NGO ( Government Public sector ) References:...

  14. Mobile Energy Products Inc | Open Energy Information

    Open Energy Info (EERE)

    Name: Mobile Energy Products Inc Place: Colorado Springs, Colorado Sector: Hydro, Hydrogen Product: Manufacturing subsidiary, which produces nickel sintered plaque for...

  15. Public Transport: Moving towards Sustainable Mobility | Open...

    Open Energy Info (EERE)

    to: navigation, search Tool Summary LAUNCH TOOL Name: Public Transport: Moving towards Sustainable Mobility AgencyCompany Organization: United Nations Environment Programme...

  16. Running Greener: E-Mobility at SAP

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    CO 2 neutral Reduce consumption of fossil fuels and noise Environmental Mobility Unique battery subsidy as benefit Enjoy free charging exclusively at SAP's charging spots...

  17. Differential homogeneous immunosensor device

    DOE Patents [OSTI]

    Malmros, M.K.; Gulbinski, J. III.

    1990-04-10

    There is provided a novel method of testing for the presence of an analyte in a fluid suspected of containing the same. In this method, in the presence of the analyte, a substance capable of modifying certain characteristics of the substrate is bound to the substrate and the change in these qualities is measured. While the method may be modified for carrying out quantitative differential analyses, it eliminates the need for washing the analyte from the substrate which is characteristic of prior art methods. 12 figs.

  18. DIFFERENTIAL FAULT SENSING CIRCUIT

    DOE Patents [OSTI]

    Roberts, J.H.

    1961-09-01

    A differential fault sensing circuit is designed for detecting arcing in high-voltage vacuum tubes arranged in parallel. A circuit is provided which senses differences in voltages appearing between corresponding elements likely to fault. Sensitivity of the circuit is adjusted to some level above which arcing will cause detectable differences in voltage. For particular corresponding elements, a group of pulse transformers are connected in parallel with diodes connected across the secondaries thereof so that only voltage excursions are transmitted to a thyratron which is biased to the sensitivity level mentioned.

  19. Interdigitated Electrical Contacts for Low Electronic Mobility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Semiconductor Photovoltaic Devices - Energy Innovation Portal Solar Photovoltaic Solar Photovoltaic Find More Like This Return to Search Interdigitated Electrical Contacts for Low Electronic Mobility Semiconductor Photovoltaic Devices Brookhaven National Laboratory Contact BNL About This Technology Technology Marketing Summary Structures useful for forming contacts to materials having low charge carrier mobility are described. Methods for their formation and use are also described. These

  20. Sour gas dehydration in Mobile Bay

    SciTech Connect (OSTI)

    Betts, F.C. Jr.; Lay, A.G.

    1996-12-31

    An evaluation of Mobil`s different methods of sour gas development utilized offshore and processes selected are presented with the maintenance history. The conclusions are based on field data showing past performance with a correlation made for future development and the selection criteria for dehydration.

  1. MobileWeb.jpg | OSTI, US Dept of Energy Office of Scientific and Technical

    Office of Scientific and Technical Information (OSTI)

    Information MobileWeb

  2. Dynamic Analysis of Mobile Device Applications

    SciTech Connect (OSTI)

    Corey Thuen

    2013-01-01

    The On-Device Dynamic Analysis of Mobile Applications (ODAMA) project was started in an effort to protect mobile devices used in Industrial Control Systems (ICS) from cyber attack. Because mobile devices hide as much of the computer as possible, the users ability to assess the software running on their system is limited. The research team chose Googles Android platform for this initial research because it is open source and it would give us freedom in our approach, including the ability to modify the mobile devices operating system itself. The research team concluded that a Privileged Application was the right approach, and the result was ODAMA. This project is an important piece of the work to secure the expanding use of mobile devices with our nations critical infrastructure.

  3. DIFFERENTIAL PULSE HEIGHT DISCRIMINATOR

    DOE Patents [OSTI]

    Test, L.D.

    1958-11-11

    Pulse-height discriminators are described, specifically a differential pulse-height discriminator which is adapted to respond to pulses of a band of amplitudes, but to reject pulses of amplitudes greater or less than tbe preselected band. In general, the discriminator includes a vacuum tube having a plurality of grids adapted to cut off plate current in the tube upon the application of sufficient negative voltage. One grid is held below cutoff, while a positive pulse proportional to the amplltude of each pulse is applled to this grid. Another grid has a negative pulse proportional to the amplitude of each pulse simultaneously applied to it. With this arrangement the tube will only pass pulses which are of sufficlent amplitude to counter the cutoff bias but not of sufficlent amplitude to cutoff the tube.

  4. Three-junction solar cells comprised of a thin-film GaInP/GaAs tandem cell mechanically stacked on a Si cell

    SciTech Connect (OSTI)

    Yazawa, Y.; Tamura, K.; Watahiki, S.; Kitatani, T.; Ohtsuka, H.; Warabisako, T.

    1997-12-31

    Three-junction tandem solar cells were fabricated by mechanical stacking of a thin-film GaInP/GaAs monolithic tandem cell and a Si cell. The epitaxial lift-off (ELO) technique was used for the thinning of GaInP/GaAs tandem cells. Both spectral responses of the GaInP top cell and the GaAs middle cell in the thin-film GaInP/GaAs monolithic tandem cell were conserved. The Si cell performance has been improved by reducing the absorption loss in the GaAs substrate.

  5. DOE Science Showcase - Research on the "Go" with OSTI mobile...

    Office of Scientific and Technical Information (OSTI)

    Research on the "Go" with OSTI mobile Now you can find full-text technical reports from the Department of Energy from your mobile device. The new mobile OSTI website http:...

  6. Feasibility of CO2 Capture from Mobile Sources | Department of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    CO2 Capture from Mobile Sources Feasibility of CO2 Capture from Mobile Sources Presents integrated system for post-combustion CO2 capture from mobile sources PDF icon ...

  7. Enhancement of efficiencies for tandem green phosphorescent organic light-emitting devices with a p-type charge generation layer

    SciTech Connect (OSTI)

    Yoo, Byung Soo; Jeon, Young Pyo; Lee, Dae Uk; Kim, Tae Whan

    2014-10-15

    The operating voltage of the tandem green phosphorescent organic light-emitting device with a 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile layer was improved by 3% over that of the organic light-emitting device with a molybdenum trioxide layer. The maximum brightness of the tandem green phosphorescent organic light-emitting device at 21.9 V was 26,540 cd/m{sup 2}. The dominant peak of the electroluminescence spectra for the devices was related to the fac-tris(2-phenylpyridine) iridium emission. - Highlights: Tandem OLEDs with CGL were fabricated to enhance their efficiency. The operating voltage of the tandem OLED with a HAT-CN layer was improved by 3%. The efficiency and brightness of the tandem OLED were 13.9 cd/A and 26,540 cd/m{sup 2}. Efficiency of the OLED with a HAT-CN layer was lower than that with a MoO{sub 3} layer. - Abstract: Tandem green phosphorescent organic light-emitting devices with a 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile or a molybdenum trioxide charge generation layer were fabricated to enhance their efficiency. Current densityvoltage curves showed that the operating voltage of the tandem green phosphorescent organic light-emitting device with a 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile layer was improved by 3% over that of the corresponding organic light-emitting device with a molybdenum trioxide layer. The efficiency and the brightness of the tandem green phosphorescent organic light-emitting device were 13.9 cd/A and 26,540 cd/m{sup 2}, respectively. The current efficiency of the tandem green phosphorescent organic light-emitting device with a 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile layer was lower by 1.1 times compared to that of the corresponding organic light-emitting device with molybdenum trioxide layer due to the decreased charge generation and transport in the 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile layer resulting from triplettriplet exciton annihilation.

  8. Mobile interfaces: Liquids as a perfect structural material for...

    Office of Scientific and Technical Information (OSTI)

    Mobile interfaces: Liquids as a perfect structural material for multifunctional, antifouling surfaces Title: Mobile interfaces: Liquids as a perfect structural material for ...

  9. How Would You Use Your Mobile Device to Save Energy?

    Broader source: Energy.gov [DOE]

    More and more, people are using their phones and mobile devices to find information -- tell us how you would use your mobile device to save energy.

  10. Using Mobile Applications to Generate Customer Demand | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Using Mobile Applications to Generate Customer Demand Using Mobile Applications to Generate Customer Demand Better Buildings Residential Network Peer Exchange Call Series: Using...

  11. Deployment of ARM Aerial Facility (AAF) Scanning Mobility Particle...

    Office of Scientific and Technical Information (OSTI)

    Mobility Particle Sizer Field Campaign Report Citation Details In-Document Search Title: Deployment of ARM Aerial Facility (AAF) Scanning Mobility Particle Sizer Field ...

  12. TSI Model 3936 Scanning Mobility Particle Spectrometer Instrument...

    Office of Scientific and Technical Information (OSTI)

    TSI Model 3936 Scanning Mobility Particle Spectrometer Instrument Handbook Citation Details In-Document Search Title: TSI Model 3936 Scanning Mobility Particle Spectrometer ...

  13. Mobile Gallery | OSTI, US Dept of Energy Office of Scientific...

    Office of Scientific and Technical Information (OSTI)

    Mobile Gallery OSTI.gov Mobile Get full-text documents, citations, patents, green energy research results, and more. Narrow results by document type, download and email results. ...

  14. V-235: Cisco Mobility Services Engine Configuration Error Lets...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    5: Cisco Mobility Services Engine Configuration Error Lets Remote Users Login Anonymously V-235: Cisco Mobility Services Engine Configuration Error Lets Remote Users Login ...

  15. MHK Technologies/Mobil Stabilized Energy Conversion Platform...

    Open Energy Info (EERE)

    Mobil Stabilized Energy Conversion Platform < MHK Technologies Jump to: navigation, search << Return to the MHK database homepage Mobil Stabilized Energy Conversion Platform.jpg...

  16. And the Oscar for Sustainable Mobile Lighting Goes to.... Lighting...

    Broader source: Energy.gov (indexed) [DOE]

    There are about 100,000 diesel-powered mobile lighting towers in the United States, ... building, and testing a mobile lighting tower powered by hydrogen fuel cell ...

  17. Case Study: Mobile Photovoltaic System at Bechler Meadows Ranger...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Mobile Photovoltaic System at Bechler Meadows Ranger Station, Yellowstone National Park Case Study: Mobile Photovoltaic System at Bechler Meadows Ranger Station, Yellowstone ...

  18. Mobile Gallery | OSTI, US Dept of Energy, Office of Scientific...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mobile Gallery OSTI.gov Mobile Get full-text documents, citations, patents, green energy research results, and more. Narrow results by document type, download and email results. ...

  19. Persu Mobility was Venture Vehicles Inc | Open Energy Information

    Open Energy Info (EERE)

    Persu Mobility was Venture Vehicles Inc Jump to: navigation, search Name: Persu Mobility (was Venture Vehicles Inc) Place: Los Angeles, California Zip: 90067 Product: Los Angeles...

  20. GATE: Energy Efficient Vehicles for Sustainable Mobility | Department...

    Broader source: Energy.gov (indexed) [DOE]

    GATE: Energy Efficient Vehicles for Sustainable Mobility Vehicle Technologies Office Merit Review 2014: GATE: Energy Efficient Vehicles for Sustainable Mobility Vehicle ...

  1. ARM Operations and Engineering Procedure Mobile Facility Site...

    Office of Scientific and Technical Information (OSTI)

    ARM Operations and Engineering Procedure Mobile Facility Site Startup Citation Details In-Document Search Title: ARM Operations and Engineering Procedure Mobile Facility Site Startup ...

  2. Fuel Economy.gov - Mobile | Open Energy Information

    Open Energy Info (EERE)

    Economy.gov - Mobile Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Fuel Economy.gov - Mobile AgencyCompany Organization: United States Department of Energy Sector:...

  3. Public Finance Mechanisms to Mobilize Investment in Climate Change...

    Open Energy Info (EERE)

    Mobilize Investment in Climate Change Mitigation Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Public Finance Mechanisms to Mobilize Investment in Climate Change...

  4. Automotive Fuels - The Challenge for Sustainable Mobility | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fuels - The Challenge for Sustainable Mobility Automotive Fuels - The Challenge for Sustainable Mobility Overview of challenges and future fuel options deer12warnecke.pdf (1.72 ...

  5. Engineers Go Mobile with Tablets, Bring Benefits to Waste Treatment...

    Energy Savers [EERE]

    Engineers Go Mobile with Tablets, Bring Benefits to Waste Treatment Plant Project Engineers Go Mobile with Tablets, Bring Benefits to Waste Treatment Plant Project June 15, 2016 - ...

  6. Acid–base bifunctional shell cross-linked micelle nanoreactor for one-pot tandem reaction

    SciTech Connect (OSTI)

    Lee, Li -Chen; Lu, Jie; Weck, Marcus; Jones, Christopher W.

    2015-12-29

    Shell cross-linked micelles (SCMs) containing acid sites in the shell and base sites in the core are prepared from amphiphilic poly(2-oxazoline) triblock copolymers. The materials are utilized as two-chamber nanoreactors for a prototypical acid-base bifunctional tandem deacetalization-nitroaldol reaction. Furthermore, the acid and base sites are localized in different regions of the micelle, allowing the two steps in the reaction sequence to largely proceed in separate compartments, akin to the compartmentalization that occurs in biological systems.

  7. Acidbase bifunctional shell cross-linked micelle nanoreactor for one-pot tandem reaction

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Lee, Li -Chen; Lu, Jie; Weck, Marcus; Jones, Christopher W.

    2015-12-29

    Shell cross-linked micelles (SCMs) containing acid sites in the shell and base sites in the core are prepared from amphiphilic poly(2-oxazoline) triblock copolymers. The materials are utilized as two-chamber nanoreactors for a prototypical acid-base bifunctional tandem deacetalization-nitroaldol reaction. Furthermore, the acid and base sites are localized in different regions of the micelle, allowing the two steps in the reaction sequence to largely proceed in separate compartments, akin to the compartmentalization that occurs in biological systems.

  8. Radiation detection system using semiconductor detector with differential carrier trapping and mobility

    DOE Patents [OSTI]

    Whited, Richard C. (Santa Barbara, CA)

    1981-01-01

    A system for obtaining improved resolution in relatively thick semiconductor radiation detectors, such as HgI.sub.2, which exhibit significant hole trapping. Two amplifiers are used: the first measures the charge collected and the second the contribution of the electrons to the charge collected. The outputs of the two amplifiers are utilized to unfold the total charge generated within the detector in response to a radiation event.

  9. Method for enhancing the resolving power of ion mobility separations over a limited mobility range

    DOE Patents [OSTI]

    Shvartsburg, Alexandre A; Tang, Keqi; Smith, Richard D

    2014-09-23

    A method for raising the resolving power, specificity, and peak capacity of conventional ion mobility spectrometry is disclosed. Ions are separated in a dynamic electric field comprising an oscillatory field wave and opposing static field, or at least two counter propagating waves with different parameters (amplitude, profile, frequency, or speed). As the functional dependencies of mean drift velocity on the ion mobility in a wave and static field or in unequal waves differ, only single species is equilibrated while others drift in either direction and are mobility-separated. An ion mobility spectrum over a limited range is then acquired by measuring ion drift times through a fixed distance inside the gas-filled enclosure. The resolving power in the vicinity of equilibrium mobility substantially exceeds that for known traveling-wave or drift-tube IMS separations, with spectra over wider ranges obtainable by stitching multiple segments. The approach also enables low-cutoff, high-cutoff, and bandpass ion mobility filters.

  10. Effective Protocols for Mobile Communications and Networking

    SciTech Connect (OSTI)

    Espinoza, J.; Sholander, P.; Van Leeuwen, B,

    1998-12-01

    This report examines methods of mobile communications with an emphasis on mobile computing and wireless communications. Many of the advances in communications involve the use of Internet Protocol (IP), Asynchronous Transfer Mode (ATM), and ad hoc network protocols. However, many of the advances in these protocols have been focused on wired communications. Recently much focus has been directed at advancing communication technology in the area of mobile wireless networks. This report discusses various protocols used in mobile communications and proposes a number of extensions to existing protocols. A detailed discussion is also included on desirable protocol characteristics and evaluation criteria. In addition, the report includes a discussion on several network simulation tools that maybe used to evaluate network protocols.

  11. Tandem catalysis by palladium nanoclusters encapsulated in metal–organic frameworks

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Li, Xinle; Guo, Zhiyong; Xiao, Chaoxian; Goh, Tian Wei; Tesfagaber, Daniel; Huang, Wenyu

    2014-08-25

    A bifunctional Zr-MOF catalyst containing palladium nanoclusters (NCs) has been developed. The formation of Pd NCs was confirmed by transmission electron microscopy (TEM) and extended X-ray absorption fine structure (EXAFS). Combining the oxidation activity of Pd NCs and the acetalization activity of the Lewis acid sites in UiO-66-NH2, this catalyst (Pd@UiO-66-NH2) exhibits excellent catalytic activity and selectivity in a one-pot tandem oxidation-acetalization reaction. This catalyst shows 99.9% selectivity to benzaldehyde ethylene acetal in the tandem reaction of benzyl alcohol and ethylene glycol at 99.9% conversion of benzyl alcohol. We also examined various substituted benzyl alcohols and found that alcohols withmore » electron-donating groups showed better conversion and selectivity compared to those with electron-withdrawing groups. As a result, we further proved that there was no leaching of active catalytic species during the reaction and the catalyst can be recycled at least five times without significant deactivation.« less

  12. Simulations of emission from microcavity tandem organic light-emitting diodes

    SciTech Connect (OSTI)

    Biswas, Rana; Xu, Chun; Zhao, Weijun; Liu, Rui; Shinar, Ruth; Shinar, Joseph

    2011-01-01

    Microcavity tandem organic light-emitting diodes (OLEDs) are simulated and compared to experimental results. The simulations are based on two complementary techniques: rigorous finite element solutions of Maxwell's equations and Fourier space scattering matrix solutions. A narrowing and blue shift of the emission spectrum relative to the noncavity single unit OLED is obtained both theoretically and experimentally. In the simulations, a distribution of emitting sources is placed near the interface of the electron transport layer tris(8-hydroxyquinoline) Al (Alq{sub 3}) and the hole transport layer (N,N'-bis(naphthalen-1-yl)-N,N'-bis(phenyl)benzidine) ({alpha}-NPB). Far-field electric field intensities are simulated. The simulated widths of the emission peaks also agree with the experimental results. The simulations of the 2-unit tandem OLEDs shifted the emission to shorter wavelength, in agreement with experimental measurements. The emission spectra's dependence on individual layer thicknesses also agreed well with measurements. Approaches to simulate and improve the light emission intensity from these OLEDs, in particular for white OLEDs, are discussed.

  13. Tandem catalysis by palladium nanoclusters encapsulated in metal–organic frameworks

    SciTech Connect (OSTI)

    Li, Xinle; Guo, Zhiyong; Xiao, Chaoxian; Goh, Tian Wei; Tesfagaber, Daniel; Huang, Wenyu

    2014-08-25

    A bifunctional Zr-MOF catalyst containing palladium nanoclusters (NCs) has been developed. The formation of Pd NCs was confirmed by transmission electron microscopy (TEM) and extended X-ray absorption fine structure (EXAFS). Combining the oxidation activity of Pd NCs and the acetalization activity of the Lewis acid sites in UiO-66-NH2, this catalyst (Pd@UiO-66-NH2) exhibits excellent catalytic activity and selectivity in a one-pot tandem oxidation-acetalization reaction. This catalyst shows 99.9% selectivity to benzaldehyde ethylene acetal in the tandem reaction of benzyl alcohol and ethylene glycol at 99.9% conversion of benzyl alcohol. We also examined various substituted benzyl alcohols and found that alcohols with electron-donating groups showed better conversion and selectivity compared to those with electron-withdrawing groups. As a result, we further proved that there was no leaching of active catalytic species during the reaction and the catalyst can be recycled at least five times without significant deactivation.

  14. Tandem Microwire Solar Cells for Flexible High Efficiency Low Cost Photovoltaics

    SciTech Connect (OSTI)

    Atwater, Harry A.

    2015-03-10

    This project has developed components of a waferless, flexible, low-cost tandem multijunction III-V/Si microwire array solar cell technology which combines the efficiency of wafered III-V photovoltaic technologies with the process designed to meet the Sunshot object. The project focused on design of lattice-matched GaAsP/SiGe two junction cell design and lattice-mismatched GaInP/Si tandem cell design. Combined electromagnetic simulation/device physics models using realistic microwire tandem structures were developed that predict >22% conversion efficiency for known material parameters, such as tunnel junction structure, window layer structure, absorber lifetimes and optical absorption and these model indicate a clear path to 30% efficiency for high quality III-V heterostructures. SiGe microwire arrays were synthesized via Cu-catalyzed vapor-liquid-solid (VLS) growth with inexpensive chlorosilane and chlorogermance precursors in an atmospheric pressure reactor. SiGe alloy composition in microwires was found to be limited to a maximum of 12% Ge incorporation during chlorogermane growth, due to the melting of the alloy near the solidus composition. Lattice mismatched InGaP double heterostructures were grown by selective epitaxy with a thermal oxide mask on Si microwire substrates using metallorganic vapor phase epitaxy. Transmission electron microscopy (TEM) analysis confirms the growth of individual step graded layers and a high density of defects near the wire/III-V interface. Selective epitaxy was initiated with a low temperature nucleation scheme under “atomic layer epitaxy” or “flow mediated epitaxy” conditions whereby the Ga and P containing precursors are alternately introduced into the reactor to promote layer-bylayer growth. In parallel to our efforts on conformal GaInP heteroepitaxy on selectively masked Si microwires, we explored direct, axial growth of GaAs on Si wire arrays as another route to a tandem junction architecture. We proposed axial

  15. Characterization of protein N-glycosylation by tandem mass spectrometry using complementary fragmentation techniques

    SciTech Connect (OSTI)

    Ford, Kristina L.; Zeng, Wei; Heazlewood, Joshua L.; Bacic, Antony

    2015-08-28

    The analysis of post-translational modifications (PTMs) by proteomics is regarded as a technically challenging undertaking. While in recent years approaches to examine and quantify protein phosphorylation have greatly improved, the analysis of many protein modifications, such as glycosylation, are still regarded as problematic. Limitations in the standard proteomics workflow, such as use of suboptimal peptide fragmentation methods, can significantly prevent the identification of glycopeptides. The current generation of tandem mass spectrometers has made available a variety of fragmentation options, many of which are becoming standard features on these instruments. Lastly, we have used three common fragmentation techniques, namely CID, HCD, and ETD, to analyze a glycopeptide and highlight how an integrated fragmentation approach can be used to identify the modified residue and characterize the N-glycan on a peptide.

  16. Toward a Monolithic Lattice-Matched III-V on Silicon Tandem Solar Cell

    SciTech Connect (OSTI)

    Geisz, J. F.; Olson, J. M.; Friedman, D. J.

    2004-09-01

    A two-junction device consisting of a 1.7-eV GaNPAs junction on a 1.1-eV silicon junction has the theoretical potential to achieve nearly optimal efficiency for a two-junction tandem cell. We have demonstrated some of the key components toward realizing such a cell, including GaNPAs top cells grown on silicon substrates, GaP-based tunnel junctions grown on silicon substrates, and diffused silicon junctions formed during the epitaxial growth of GaNP on silicon. These components have required the development of techniques for the growth of high crystalline quality GaNPAs on silicon by metal-organic vapor-phase epitaxy.

  17. In Silico Identification Software (ISIS): A Machine Learning Approach to Tandem Mass Spectral Identification of Lipids

    SciTech Connect (OSTI)

    Kangas, Lars J.; Metz, Thomas O.; Isaac, Georgis; Schrom, Brian T.; Ginovska-Pangovska, Bojana; Wang, Luning; Tan, Li; Lewis, Robert R.; Miller, John H.

    2012-05-15

    Liquid chromatography-mass spectrometry-based metabolomics has gained importance in the life sciences, yet it is not supported by software tools for high throughput identification of metabolites based on their fragmentation spectra. An algorithm (ISIS: in silico identification software) and its implementation are presented and show great promise in generating in silico spectra of lipids for the purpose of structural identification. Instead of using chemical reaction rate equations or rules-based fragmentation libraries, the algorithm uses machine learning to find accurate bond cleavage rates in a mass spectrometer employing collision-induced dissocia-tion tandem mass spectrometry. A preliminary test of the algorithm with 45 lipids from a subset of lipid classes shows both high sensitivity and specificity.

  18. Characterization of protein N-glycosylation by tandem mass spectrometry using complementary fragmentation techniques

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Ford, Kristina L.; Zeng, Wei; Heazlewood, Joshua L.; Bacic, Antony

    2015-08-28

    The analysis of post-translational modifications (PTMs) by proteomics is regarded as a technically challenging undertaking. While in recent years approaches to examine and quantify protein phosphorylation have greatly improved, the analysis of many protein modifications, such as glycosylation, are still regarded as problematic. Limitations in the standard proteomics workflow, such as use of suboptimal peptide fragmentation methods, can significantly prevent the identification of glycopeptides. The current generation of tandem mass spectrometers has made available a variety of fragmentation options, many of which are becoming standard features on these instruments. Lastly, we have used three common fragmentation techniques, namely CID, HCD,more » and ETD, to analyze a glycopeptide and highlight how an integrated fragmentation approach can be used to identify the modified residue and characterize the N-glycan on a peptide.« less

  19. Wide size range fast integrated mobility spectrometer

    DOE Patents [OSTI]

    Wang, Jian

    2013-10-29

    A mobility spectrometer to measure a nanometer particle size distribution is disclosed. The mobility spectrometer includes a conduit and a detector. The conduit is configured to receive and provide fluid communication of a fluid stream having a charged nanometer particle mixture. The conduit includes a separator section configured to generate an electrical field of two dimensions transverse to a dimension associated with the flow of the charged nanometer particle mixture through the separator section to spatially separate charged nanometer particles of the charged nanometer particle mixture in said two dimensions. The detector is disposed downstream of the conduit to detect concentration and position of the spatially-separated nanometer particles.

  20. Oak Ridge Mobile Agent Community (ORMAC)

    Energy Science and Technology Software Center (OSTI)

    2003-06-30

    The Oak Ridge Mobile Agent Community (ORMAC) framework software facilitates the execution of a collection of mobile software agents across a heterogeneous collection of computer systems. ORMAC provides the software agents with the ability to communicate with each other in a synchronous and asynchronous manner. Also, ORMAC allows the software agents to move to any computer system in the community and continue execution there. ORMAC is intended to aid programmers in solving a very generalmore » set of distributed software problems.« less

  1. Robotic vehicle with multiple tracked mobility platforms

    DOE Patents [OSTI]

    Salton, Jonathan R. (Albuquerque, NM); Buttz, James H. (Albuquerque, NM); Garretson, Justin (Albuquerque, NM); Hayward, David R. (Wetmore, CO); Hobart, Clinton G. (Albuquerque, NM); Deuel, Jr., Jamieson K. (Albuquerque, NM)

    2012-07-24

    A robotic vehicle having two or more tracked mobility platforms that are mechanically linked together with a two-dimensional coupling, thereby forming a composite vehicle of increased mobility. The robotic vehicle is operative in hazardous environments and can be capable of semi-submersible operation. The robotic vehicle is capable of remote controlled operation via radio frequency and/or fiber optic communication link to a remote operator control unit. The tracks have a plurality of track-edge scallop cut-outs that allow the tracks to easily grab onto and roll across railroad tracks, especially when crossing the railroad tracks at an oblique angle.

  2. The effects of mobile ATM switches on PNNI peer group operation

    SciTech Connect (OSTI)

    Martinez, L.; Sholander, P.; Tolendino, L.

    1997-04-01

    This contribution discusses why, and how, mobile networks and mobile switches might be discussed during Phase 1 of the WATM standards process. Next, it reviews mobile routers within Mobile IP. That IP mobility architecture may not apply to the proposed mobile ATM switches. Finally, it discusses problems with PNNI peer group formation and operation when mobile ATM switches are present.

  3. Mobility of atoms under ion bombardment

    SciTech Connect (OSTI)

    Alekseevskii, V.; Gertsriken, D.; Kovtun, V.; Tyshkevich, V.; Fal'chenko, V.

    1981-10-01

    Argon ions bombardment (Eapprox.1KeV) of Armco iron in a cold glow discharge plasma (T< or approx. =150/sup 0/C) has been performed to investigate the mobility and behavior of the atoms in the crystal lattice and the formation of a solid solution of Argon in iron.(AIP)

  4. Portable control device for networked mobile robots

    DOE Patents [OSTI]

    Feddema, John T.; Byrne, Raymond H.; Bryan, Jon R.; Harrington, John J.; Gladwell, T. Scott

    2002-01-01

    A handheld control device provides a way for controlling one or multiple mobile robotic vehicles by incorporating a handheld computer with a radio board. The device and software use a personal data organizer as the handheld computer with an additional microprocessor and communication device on a radio board for use in controlling one robot or multiple networked robots.

  5. Mobile workstation for decontamination and decommissioning operations

    SciTech Connect (OSTI)

    Whittaker, W.L.; Osborn, J.F.; Thompson, B.R.

    1993-10-01

    This project is an interdisciplinary effort to develop effective mobile worksystems for decontamination and decommissioning (D&D) of facilities within the DOE Nuclear Weapons Complex. These mobile worksystems will be configured to operate within the environmental and logistical constraints of such facilities and to perform a number of work tasks. Our program is designed to produce a mobile worksystem with capabilities and features that are matched to the particular needs of D&D work by evolving the design through a series of technological developments, performance tests and evaluations. The project has three phases. In this the first phase, an existing teleoperated worksystem, the Remote Work Vehicle (developed for use in the Three Mile Island Unit 2 Reactor Building basement), was enhanced for telerobotic performance of several D&D operations. Its ability to perform these operations was then assessed through a series of tests in a mockup facility that contained generic structures and equipment similar to those that D&D work machines will encounter in DOE facilities. Building upon the knowledge gained through those tests and evaluations, a next generation mobile worksystem, the RWV II, and a more advanced controller will be designed, integrated and tested in the second phase, which is scheduled for completion in January 1995. The third phase of the project will involve testing of the RWV II in the real DOE facility.

  6. Mobility of organic carbon from incineration residues

    SciTech Connect (OSTI)

    Ecke, Holger Svensson, Malin

    2008-07-01

    Dissolved organic carbon (DOC) may affect the transport of pollutants from incineration residues when landfilled or used in geotechnical construction. The leaching of dissolved organic carbon (DOC) from municipal solid waste incineration (MSWI) bottom ash and air pollution control residue (APC) from the incineration of waste wood was investigated. Factors affecting the mobility of DOC were studied in a reduced 2{sup 6-1} experimental design. Controlled factors were treatment with ultrasonic radiation, full carbonation (addition of CO{sub 2} until the pH was stable for 2.5 h), liquid-to-solid (L/S) ratio, pH, leaching temperature and time. Full carbonation, pH and the L/S ratio were the main factors controlling the mobility of DOC in the bottom ash. Approximately 60 weight-% of the total organic carbon (TOC) in the bottom ash was available for leaching in aqueous solutions. The L/S ratio and pH mainly controlled the mobilization of DOC from the APC residue. About 93 weight-% of TOC in the APC residue was, however, not mobilized at all, which might be due to a high content of elemental carbon. Using the European standard EN 13 137 for determination of total organic carbon (TOC) in MSWI residues is inappropriate. The results might be biased due to elemental carbon. It is recommended to develop a TOC method distinguishing between organic and elemental carbon.

  7. Texas Tech University mobile doppler radars provide unique wind...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Texas Tech University mobile doppler radars provide unique wind measurements to multi-instrument DOE Field Campaign HomeWind Energy, Wind NewsTexas Tech University mobile doppler ...

  8. Ordinary Differential Equation System Solver

    Energy Science and Technology Software Center (OSTI)

    1992-03-05

    LSODE is a package of subroutines for the numerical solution of the initial value problem for systems of first order ordinary differential equations. The package is suitable for either stiff or nonstiff systems. For stiff systems the Jacobian matrix may be treated in either full or banded form. LSODE can also be used when the Jacobian can be approximated by a band matrix.

  9. Novel wide band gap materials for highly efficient thin film tandem solar cells

    SciTech Connect (OSTI)

    Brian E. Hardin, Stephen T. Connor, Craig H. Peters

    2012-06-11

    Tandem solar cells (TSCs), which use two or more materials to absorb sunlight, have achieved power conversion efficiencies of >25% versus 11-20% for commercialized single junction solar cell modules. The key to widespread commercialization of TSCs is to develop the wide-band, top solar cell that is both cheap to fabricate and has a high open-circuit voltage (i.e. >1V). Previous work in TSCs has generally focused on using expensive processing techniques with slow growth rates resulting in costs that are two orders of magnitude too expensive to be used in conventional solar cell modules. The objective of the PLANT PV proposal was to investigate the feasibility of using Ag(In,Ga)Se2 (AIGS) as the wide-bandgap absorber in the top cell of a thin film tandem solar cell (TSC). Despite being studied by very few in the solar community, AIGS solar cells have achieved one of the highest open-circuit voltages within the chalcogenide material family with a Voc of 949mV when grown with an expensive processing technique (i.e. Molecular Beam Epitaxy). PLANT PVâ??s goal in Phase I of the DOE SBIR was to 1) develop the chemistry to grow AIGS thin films via solution processing techniques to reduce costs and 2) fabricate new device architectures with high open-circuit voltage to produce full tandem solar cells in Phase II. PLANT PV attempted to translate solution processing chemistries that were successful in producing >12% efficient Cu(In,Ga)Se2 solar cells by replacing copper compounds with silver. The main thrust of the research was to determine if it was possible to make high quality AIGS thin films using solution processing and to fully characterize the materials properties. PLANT PV developed several different types of silver compounds in an attempt to fabricate high quality thin films from solution. We found that silver compounds that were similar to the copper based system did not result in high quality thin films. PLANT PV was able to deposit AIGS thin films using a

  10. WPN 93-5: Recommended Installation Standards for Mobile Homes

    Broader source: Energy.gov [DOE]

    To provide technical assistance to the states on recommended installation techniques for weatherization materials installed on mobile homes.

  11. Comments on: Texas Tech University mobile doppler radars provide...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    texas-tech-university-mobile-doppler-radars-provide-unique-wind-measurements-to-multi-instrument-doe-field-campaign...

  12. Progress Update: Creating Mobile Emission Reduction Credits | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Update: Creating Mobile Emission Reduction Credits Progress Update: Creating Mobile Emission Reduction Credits 2004 Diesel Engine Emissions Reduction (DEER) Conference Presentation: Emission Reduction Specialists 2004_deer_sloan.pdf (48.07 KB) More Documents & Publications Creating Mobile Emission Reduction Credits ADEC II Universal SCR Retrofit System for On-road and Off-road Diesel Engines SCR & DPF RETROFITS FOR MOBILE DIESEL ENGINES

  13. WE-A-17A-05: Differences in Applicator Configuration and Dwell Loading Between Standard and Image-Guided Tandem and Ring (T and R) HDR Brachytherapy

    SciTech Connect (OSTI)

    Damato, A; Cormack, R; Bhagwat, M; Buzurovic, I; Lee, L; Viswanathan, A

    2014-06-15

    Purpose: To investigate differences in: (i) relative location of the tandem and the ring compared to a rigid standard applicator model; and (ii) relative loading and changes in loading pattern between standard and image-guided planning. Methods: All T and R insertions performed in 2013 in our institution under CT- or MR-guidance were analyzed. Standard plans were generated using library applicator models with a fixed relationship between ring and tandem, standardized uniform dwell loading and normalization to point A. The graphic plans and the associated standard-plan dwell configurations were compared: the rings were rigidly registered, and the residual tandem shift, rotation and maximum distance between plan tandem dwell and corresponding model tandem dwell were calculated. The normalization ratio (NR = the ratio of graphic versus standard-plan total reference air kerma [TRAK]), the general loading difference (GLD = the difference between graphic and standard ratios of the tandem versus the ring TRAK), and the percent standard deviation (SD% = SD/mean) of the tandem and the ring TRAK for the graphic plan (all standard-plans SD% = 0) were calculated. Results: 71 T and R were analyzed. Residual tandem shift, rotation and maximum corresponding dwell distance were 1.2±0.8mm (0.4±0.4mm lateral, 0.9±0.8mm craniocaudal, 0.4±0.3mm anterior-posterior), 2.3±1.9deg and 3.4±2.3mm. NR was 0.86±0.11 indicating a lower overall loading of the graphic compared to the standard plans. GLD was -0.12±0.16 indicating a modest increased ring loading relative to the tandem in the graphic plans. SD% was 2.1±1.6% for tandem and 2.8±1.9% for ring, indicating small deviations from uniform loading. Conclusion: Variability in the relative locations of the tandem and the ring necessitates the independent registration of each component model for accurate digitization. Our clinical experience suggests that graphically planned T and R results on average in a lower total dose to the

  14. Design of Integrated III-Nitride/Non-III-Nitride Tandem Photovoltaic Devices

    SciTech Connect (OSTI)

    Toledo, N. G.; Friedman, D.J.; Farrell, R. M.; Perl, E. E.; Lin, C. T.; Bowers, J. E.; Speck, J. S.; Mishra, U. K.

    2012-03-01

    The integration of III-nitride and non-III-nitride materials for tandem solar cell applications can improve the efficiency of the photovoltaic device due to the added power contributed by the III-nitride top cell to that of high-efficiency multi-junction non-III-nitride solar cells if the device components are properly designed and optimized. The proposed tandem solar cell is comprised of a III-nitride top cell bonded to a non-III-nitride, series-constrained, multi-junction subcell. The top cell is electrically isolated, but optically coupled to the underlying subcell. The use of a III-nitride top cell is potentially beneficial when the top junction of a stand-alone non-III-nitride subcell generates more photocurrent than the limiting current of the non-III-nitride subcell. Light producing this excess current can either be redirected to the III-nitride top cell through high energy photon absorption, redirected to the lower junctions through layer thickness optimization, or a combination of both, resulting in improved total efficiency. When the non-III-nitride cell's top junction is the limiting junction, the minimum power conversion efficiency that the III-nitride top cell must contribute should compensate for the spectrum filtered from the multi-junction subcell for this design to be useful. As the III-nitride absorption edge wavelength, {lambda}{sub N}, increases, the performance of the multi-junction subcell decreases due to spectral filtering. In the most common spectra of interest (AM1.5G, AM1.5 D, and AM0), the technology to grow InGaN cells with {lambda}{sub N}<520 nm is found to be sufficient for III-nitride top cell applications. The external quantum efficiency performance, however, of state-of-the-art InGaN solar cells still needs to be improved. The effects of surface/interface reflections are also presented. The management of these reflection issues determines the feasibility of the integrated III-nitride/non-III-nitride design to improve overall cell

  15. Webinar: Fuel Cell Mobile Lighting | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Mobile Lighting Webinar: Fuel Cell Mobile Lighting Above is the video recording for the webinar, "Fuel Cell Mobile Lighting," originally held on November 13, 2012. In addition to this recording, you can access the presentation slides. A text version of this recording will be available soon

  16. SU-E-T-615: Investigation of the Dosimetric Impact of Tandem Loading in the Treatment of Cervical Cancer for HDR Brachytherapy Procedures

    SciTech Connect (OSTI)

    Esquivel, C; Patton, L; Nelson, K; Lin, B

    2014-06-01

    Purpose: To quantify the dosimetric impact of the tandem loading in the treatment of cervical cancer for HDR brachytherapy procedures. Methods: Ten patients were evaluated, each of whom received 5 fractions of treatment. Tandem and ovoid sets were inserted into the uterine cavity based on institutional protocols and procedures. Following insertion and stabilization, CT image sets of 1.5mm slice thickness were acquired and sent to the Oncentra V4.3 Treatment Planning System. Critical structures such as the CTV, bladder, rectum, sigmoid, and bowel were contoured and a fractional dose of 5.5Gy was prescribed to Point A for each patient. Six different treatment plans were created for each fraction using varying tandem weightings; from 0.5 to 1.4 times that of the ovoids. Surface dose evaluation of various ovoid diameters, 2.0-3.5cm, at the vaginal fornices was also investigated. Results: Critical structures were evaluated based on varying dose and volume constraints, in particular the 2.0 cc volume recommendation cited by the gynecological GEC-ESTRO working group. Based on dose volume histogram evaluation, a reduction of dose to the critical structures was most often discovered when the tandem weighting was increased. CTV coverage showed little change as the tandem weighting was varied. Ovoid surface dose decreased by 50-65% as the tandem weighting increased. Conclusion: The advantage of 3D planning with HDR brachytherapy is the dose optimization for each individual treatment plan. This investigation shows that by utilizing large tandem weightings, 1.4 times greater than the ovoid, one can still achieve adequate coverage of the CTV and relatively low doses to the critical structures. In some cases, one would still have to optimize further per individual case. In addition, the ovoid surface dose was greatly decreased when large tandem weighting was utilized; especially for small ovoid diameters.

  17. Conceptual design study FY 1981: synfuels from fusion - using the tandem mirror reactor and a thermochemical cycle to produce hydrogen

    SciTech Connect (OSTI)

    Krikorian, O.H.

    1982-02-09

    This report represents the second year's effort of a scoping and conceptual design study being conducted for the express purpose of evaluating the engineering potential of producing hydrogen by thermochemical cycles using a tandem mirror fusion driver. The hydrogen thus produced may then be used as a feedstock to produce fuels such as methane, methanol, or gasoline. The main objective of this second year's study has been to obtain some approximate cost figures for hydrogen production through a conceptual design study.

  18. Reply Comments of T-Mobile USA, Inc. | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    T-Mobile USA, Inc. Reply Comments of T-Mobile USA, Inc. T-Mobile USA, Inc. ("T-Mobile") hereby submits these reply comments in response to the above-captioned Request for ...

  19. wws_mobile1.jpg | OSTI, US Dept of Energy Office of Scientific and

    Office of Scientific and Technical Information (OSTI)

    Technical Information wws_mobile1

  20. Progress in High-Performance PV: Polycrystalline Thin-Film Tandem Cells

    SciTech Connect (OSTI)

    Symko-Davies, M.

    2004-08-01

    The High-Performance Photovoltaic (HiPerf PV) Project was initiated by the U.S. Department of Energy to substantially increase the viability of PV for cost-competitive applications. The goal is that PV will contribute significantly to the U.S. and world energy supply and environmental enhancement in the 21st century. The HiPerf PV Project aims at exploring the ultimate performance limits of existing PV technologies, approximately doubling their sunlight-to-electricity conversion efficiencies during its course, to accelerate and enhance their impact in the marketplace. To accomplish this, the National Center for Photovoltaics (NCPV) directs in-house and subcontracted research in high-performance polycrystalline thin-film and multijunction concentrator devices. This paper will describe progress of the subcontractor and in-house R&D on critical pathways for a PV technology having a high potential to reach cost-competitiveness goals: 25%-efficient, low-cost polycrystalline thin-film tandems for large-area, flat-plate modules.

  1. De novo sequencing of peptides from top-down tandem mass spectra

    SciTech Connect (OSTI)

    Vyatkina, Kira; Wu, Si; Dekker, Leendert J.; vanDuijn, Martijn M.; Liu, Xiaowen; Tolic, Nikola; Dvorkin, Mikhail; Alexandrova, Sonya; Luider, Theo N.; Pasa-Tolic, Ljiljana; Pevzner, Pavel A.

    2015-09-28

    De novo sequencing of proteins and peptides is one of the most important problems in mass spectrometry-driven proteomics. A variety of methods have been developed to accomplish this task from a set of bottom-up tandem (MS/MS) mass spectra. However, a more recently emerged top-down technology, now gaining more and more popularity, opens new perspectives for protein analysis and characterization, implying a need in efficient algorithms for processing this kind of MS/MS data. Here we describe a method that allows to retrieve from a set of top-down MS/MS spectra long and accurate sequence fragments of the proteins contained in a sample. To this end, we outline a strategy for generating high-quality sequence tags from top-down spectra, and introduce the concept of a T-Bruijn graph by adapting to the case of tags the notion of an A-Bruijn graph widely used in genomics. The output of the proposed approach represents the set of amino acid strings spelled out by optimal paths in the connected components of a T-Bruijn graph. We illustrate its performance on top-down datasets acquired from carbonic anhydrase 2 (CAH2) and the Fab region of alemtuzumab.

  2. Neutral Beam Injection Experiments and Related Behavior of Neutral Particles in the GAMMA 10 Tandem Mirror

    SciTech Connect (OSTI)

    Nakashima, Y. [Plasma Research Center, University of Tsukuba (Japan); Watanabe, K. [Plasma Research Center, University of Tsukuba (Japan); Higashizono, Y. [Plasma Research Center, University of Tsukuba (Japan); Ohki, T. [Plasma Research Center, University of Tsukuba (Japan); Ogita, T. [Plasma Research Center, University of Tsukuba (Japan); Shoji, M. [National Institute for Fusion Science(Japan); Kobayashi, S. [Institute of Advanced Energy, Kyoto University (Japan); Islam, M.K. [Plasma Research Center, University of Tsukuba (Japan); Kubota, Y. [Plasma Research Center, University of Tsukuba (Japan); Yoshikawa, M. [Plasma Research Center, University of Tsukuba (Japan); Kobayashi, T. [Plasma Research Center, University of Tsukuba (Japan); Yamada, M. [Plasma Research Center, University of Tsukuba (Japan); Murakami, R. [Plasma Research Center, University of Tsukuba (Japan); Cho, T. [Plasma Research Center, University of Tsukuba (Japan)

    2005-01-15

    Results of neutral beam injection (NBI) experiments in the GAMMA 10 tandem mirror plasmas are presented together with the neutral particle behavior observed in the experiments. A hydrogen neural beam was injected into the hot-ion-mode plasmas by using the injector installed in the central-cell for the plasma heating and fueling. High-energy ions produced by NBI were observed and its energy distribution was measured for the first time with a neutral particle analyzer installed in the central-cell. The temporal and spatial behavior of hydrogen was observed with axially aligned H{sub {alpha}} detectors installed from the central midplane to anchor-cell. Enhancement of hydrogen recycling due to the beam injection and the cause of the observed decrease in plasma diamagnetism are discussed. The Monte-Carlo code DEGAS for neutral transport simulation was applied to the GAMMA 10 central-cell and a 3-dimensional simulation was performed in the NBI experiment. Localization of neutral particle during the beam injection is investigated based on the simulation and it was found that the increased recycling due to the beam injection was dominant near the injection port.

  3. Structural Insights into the Cooperative Binding of SeqA to a Tandem GATC Repeat

    SciTech Connect (OSTI)

    Chung, Y.; Brendler, T; Austin, S; Guarne, A

    2009-01-01

    SeqA is a negative regulator of DNA replication in Escherichia coli and related bacteria that functions by sequestering the origin of replication and facilitating its resetting after every initiation event. Inactivation of the seqA gene leads to unsynchronized rounds of replication, abnormal localization of nucleoids and increased negative superhelicity. Excess SeqA also disrupts replication synchrony and affects cell division. SeqA exerts its functions by binding clusters of transiently hemimethylated GATC sequences generated during replication. However, the molecular mechanisms that trigger formation and disassembly of such complex are unclear. We present here the crystal structure of a dimeric mutant of SeqA [SeqA{Delta}(41-59)-A25R] bound to tandem hemimethylated GATC sites. The structure delineates how SeqA forms a high-affinity complex with DNA and it suggests why SeqA only recognizes GATC sites at certain spacings. The SeqA-DNA complex also unveils additional protein-protein interaction surfaces that mediate the formation of higher ordered complexes upon binding to newly replicated DNA. Based on this data, we propose a model describing how SeqA interacts with newly replicated DNA within the origin of replication and at the replication forks.

  4. Differential Optical Synthetic Aperture Radar

    DOE Patents [OSTI]

    Stappaerts, Eddy A. (San Ramon, CA)

    2005-04-12

    A new differential technique for forming optical images using a synthetic aperture is introduced. This differential technique utilizes a single aperture to obtain unique (N) phases that can be processed to produce a synthetic aperture image at points along a trajectory. This is accomplished by dividing the aperture into two equal "subapertures", each having a width that is less than the actual aperture, along the direction of flight. As the platform flies along a given trajectory, a source illuminates objects and the two subapertures are configured to collect return signals. The techniques of the invention is designed to cancel common-mode errors, trajectory deviations from a straight line, and laser phase noise to provide the set of resultant (N) phases that can produce an image having a spatial resolution corresponding to a synthetic aperture.

  5. MULTIPLE DIFFERENTIAL ROTARY MECHANICAL DRIVE

    DOE Patents [OSTI]

    Smits, R.G.

    1964-01-28

    This patent relates to a mechanism suitable for such applications as driving two spaced-apart spools which carry a roll film strip under conditions where the film movement must be rapidly started, stopped, and reversed while maintaining a constant tension on the film. The basic drive is provided by a variable speed, reversible rnotor coupled to both spools through a first differential mechanism and driving both spools in the same direction. A second motor, providing a constant torque, is connected to the two spools through a second differential mechanism and is coupled to impart torque to one spool in a first direction anid to the other spool in the reverse direction thus applying a constant tension to the film passing over the two spools irrespective of the speed or direction of rotation thereof. (AEC)

  6. Bioenergy 2016: Mobilizing the Bioeconomy through Innovation

    Broader source: Energy.gov [DOE]

    On July 12–14, 2016, the U.S. Department of Energy's (DOE’s) Bioenergy Technologies Office (BETO) will host its ninth annual conference—Bioenergy 2016: Mobilizing the Bioeconomy through Innovation. Partnering with the Clean Energy Research and Education Foundation (CEREF), this year's conference will focus on opportunities to grow future feedstock supplies and break through technology barriers to achieve a stronger bioeconomy.

  7. WIPP Receives Waste Characterized With Mobile System

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    For Immediate Release WIPP Receives Waste Characterized With Mobile System CARLSBAD, N.M., April 12, 2002 - The first shipment of transuranic waste characterized by the Central Characterization Project arrived Saturday (April 6) at the U.S. Department of Energy's (DOE) Waste Isolation Pilot Plant (WIPP). The shipment came to WIPP from DOE's Savannah River Site in South Carolina. The shipment was the eighth to WIPP from the Savannah River Site, but the first under the newly approved Central

  8. Analytical admittance characterization of high mobility channel

    SciTech Connect (OSTI)

    Mammeri, A. M.; Mahi, F. Z.; Varani, L.

    2015-03-30

    In this contribution, we investigate the small-signal admittance of the high electron mobility transistors field-effect channels under a continuation branching of the current between channel and gate by using an analytical model. The analytical approach takes into account the linearization of the 2D Poisson equation and the drift current along the channel. The analytical equations discuss the frequency dependence of the admittance at source and drain terminals on the geometrical transistor parameters.

  9. Improving Data Mobility & Management for International Cosmology

    SciTech Connect (OSTI)

    Borrill, Julian; Dart, Eli; Gore, Brooklin; Habib, Salman; Myers, Steven T.; Nugent, Peter; Petravick, Don; Thomas, Rollin

    2015-10-02

    In February 2015 the third workshop in the CrossConnects series, with a focus on Improving Data Mobility & Management for International Cosmology, was held at Lawrence Berkeley National Laboratory. Scientists from fields including astrophysics, cosmology, and astronomy collaborated with experts in computing and networking to outline strategic opportunities for enhancing scientific productivity and effectively managing the ever-increasing scale of scientific data.

  10. EPA Mobile Source Enforcement Memo 1A

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    UNITED STATES ENVIRONMENTAL PROTECTION AGENCY WASHINGTON, D.C. 20460 OFFICE OF ENFORCEMENT AND COMPLIANCE ASSURANCE September 4, 1997 Addendum to Mobile Source Enforcement Memorandum 1A SUBJECT: Tampering Enforcement Policy for Alternative Fuel Aftermarket Conversions A. Purpose The purpose of this document is to clarify and revise the U.S. Environmental Protection Agency's (EPA's) "tampering" enforcement policy for motor vehicles and motor vehicle engines originally designed to

  11. Mobile Robotics Activities in DOE Laboratories

    SciTech Connect (OSTI)

    Ron Lujan; Jerry Harbour; John T. Feddema; Sharon Bailey; Jacob Barhen; David Reister

    2005-03-01

    This paper will briefly outline major activities in Department of Energy (DOE) Laboratories focused on mobile platforms, both Unmanned Ground Vehicles (UGV’s) as well as Unmanned Air Vehicles (UAV’s). The activities will be discussed in the context of the science and technology construct used by the DOE Technology Roadmap for Robotics and Intelligent Machines (RIM)1 published in 1998; namely, Perception, Reasoning, Action, and Integration. The activities to be discussed span from research and development to deployment in field operations. The activities support customers in other agencies. The discussion of "perception" will include hyperspectral sensors, complex patterns discrimination, multisensor fusion and advances in LADAR technologies, including real-world perception. "Reasoning" activities to be covered include cooperative controls, distributed systems, ad-hoc networks, platform-centric intelligence, and adaptable communications. The paper will discuss "action" activities such as advanced mobility and various air and ground platforms. In the RIM construct, "integration" includes the Human-Machine Integration. Accordingly the paper will discuss adjustable autonomy and the collaboration of operator(s) with distributed UGV’s and UAV’s. Integration also refers to the applications of these technologies into systems to perform operations such as perimeter surveillance, large-area monitoring and reconnaissance. Unique facilities and test beds for advanced mobile systems will be described. Given that this paper is an overview, rather than delve into specific detail in these activities, other more exhaustive references and sources will be cited extensively.

  12. Anisotropic charged impurity-limited carrier mobility in monolayer phosphorene

    SciTech Connect (OSTI)

    Ong, Zhun-Yong; Zhang, Gang; Zhang, Yong Wei

    2014-12-07

    The room temperature carrier mobility in atomically thin 2D materials is usually far below the intrinsic limit imposed by phonon scattering as a result of scattering by remote charged impurities in its environment. We simulate the charged impurity-limited carrier mobility μ in bare and encapsulated monolayer phosphorene. We find a significant temperature dependence in the carrier mobilities (μ ∝ T{sup −γ}) that results from the temperature variability of the charge screening and varies with the crystal orientation. The anisotropy in the effective mass leads to an anisotropic carrier mobility, with the mobility in the armchair direction about one order of magnitude larger than in the zigzag direction. In particular, this mobility anisotropy is enhanced at low temperatures and high carrier densities. Under encapsulation with a high-κ overlayer, the mobility increases by up to an order of magnitude although its temperature dependence and its anisotropy are reduced.

  13. Solid state cloaking for electrical charge carrier mobility control

    SciTech Connect (OSTI)

    Zebarjadi, Mona; Liao, Bolin; Esfarjani, Keivan; Chen, Gang

    2015-07-07

    An electrical mobility-controlled material includes a solid state host material having a controllable Fermi energy level and electrical charge carriers with a charge carrier mobility. At least one Fermi level energy at which a peak in charge carrier mobility is to occur is prespecified for the host material. A plurality of particles are distributed in the host material, with at least one particle disposed with an effective mass and a radius that minimize scattering of the electrical charge carriers for the at least one prespecified Fermi level energy of peak charge carrier mobility. The minimized scattering of electrical charge carriers produces the peak charge carrier mobility only at the at least one prespecified Fermi level energy, set by the particle effective mass and radius, the charge carrier mobility being less than the peak charge carrier mobility at Fermi level energies other than the at least one prespecified Fermi level energy.

  14. Efficient Mobility Summit: Transportation and the Future of Dynamic Mobility Systems

    SciTech Connect (OSTI)

    2015-12-01

    On October 27, 2015, The U.S. Department of Energy's National Renewable Energy Laboratory (NREL) brought together local and national thought leaders to discuss the convergence of connectivity, vehicle automation, and transportation infrastructure investments at the Future Energy Efficient Mobility Workshop. The half-day workshop was held in conjunction with the Colorado Department of Transportation's (CDOT) Transportation Matters Summit and featured four panel sessions that showcased perspectives on efficient mobility from federal and state agencies, automakers and their suppliers, transportation data providers, and freight companies. This summary provides highlights from the meeting's exchanges of ideas and existing applications. Transportation's (CDOT) Transportation Matters Summit and featured four panel sessions that showcased perspectives on efficient mobility from federal and state agencies, automakers and their suppliers, transportation data providers, and freight companies. This summary provides highlights from the meeting's exchanges of ideas and existing applications.

  15. Numerical Differentiation of Noisy, Nonsmooth Data

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Chartrand, Rick

    2011-01-01

    We consider the problem of differentiating a function specified by noisy data. Regularizing the differentiation process avoids the noise amplification of finite-difference methods. We use total-variation regularization, which allows for discontinuous solutions. The resulting simple algorithm accurately differentiates noisy functions, including those which have a discontinuous derivative.

  16. Nonferromagnetic linear variable differential transformer

    DOE Patents [OSTI]

    Ellis, James F.; Walstrom, Peter L.

    1977-06-14

    A nonferromagnetic linear variable differential transformer for accurately measuring mechanical displacements in the presence of high magnetic fields is provided. The device utilizes a movable primary coil inside a fixed secondary coil that consists of two series-opposed windings. Operation is such that the secondary output voltage is maintained in phase (depending on polarity) with the primary voltage. The transducer is well-suited to long cable runs and is useful for measuring small displacements in the presence of high or alternating magnetic fields.

  17. Voltage dependence of the differential capacitance of a p{sup +}-n junction

    SciTech Connect (OSTI)

    Shekhovtsov, N. A.

    2013-04-15

    The dependences of the differential capacitance and current of a p{sup +}-n junction with a uniformly doped n region on the voltage in the junction region are calculated. The p{sup +}-n junction capacitance controls the charge change in the junction region taking into account a change in the electric field of the quasi-neutral n region and a change in its bipolar drift mobility with increasing excess charge-carrier concentration. It is shown that the change in the sign of the p{sup +}-n junction capacitance with increasing injection level is caused by a decrease in the bipolar drift mobility as the electron-hole pair concentration in the n region increases. It is shown that the p{sup +}-n junction capacitance decreases with increasing reverse voltage and tends to a constant positive value.

  18. Mobile machine hazardous working zone warning system

    DOE Patents [OSTI]

    Schiffbauer, William H.; Ganoe, Carl W.

    1999-01-01

    A warning system is provided for a mobile working machine to alert an individual of a potentially dangerous condition in the event the individual strays into a hazardous working zone of the machine. The warning system includes a transmitter mounted on the machine and operable to generate a uniform magnetic field projecting beyond an outer periphery of the machine in defining a hazardous working zone around the machine during operation thereof. A receiver, carried by the individual and activated by the magnetic field, provides an alarm signal to alert the individual when he enters the hazardous working zone of the machine.

  19. Mobile machine hazardous working zone warning system

    DOE Patents [OSTI]

    Schiffbauer, W.H.; Ganoe, C.W.

    1999-08-17

    A warning system is provided for a mobile working machine to alert an individual of a potentially dangerous condition in the event the individual strays into a hazardous working zone of the machine. The warning system includes a transmitter mounted on the machine and operable to generate a uniform magnetic field projecting beyond an outer periphery of the machine in defining a hazardous working zone around the machine during operation. A receiver, carried by the individual and activated by the magnetic field, provides an alarm signal to alert the individual when he enters the hazardous working zone of the machine. 3 figs.

  20. Analytical laboratory and mobile sampling platform

    SciTech Connect (OSTI)

    Stetzenbach, K.; Smiecinski, A.

    1996-04-30

    This is the final report for the Analytical Laboratory and Mobile Sampling Platform project. This report contains only major findings and conclusions resulting from this project. Detailed reports of all activities performed for this project were provided to the Project Office every quarter since the beginning of the project. This report contains water chemistry data for samples collected in the Nevada section of Death Valley National Park (Triangle Area Springs), Nevada Test Site springs, Pahranagat Valley springs, Nevada Test Site wells, Spring Mountain springs and Crater Flat and Amargosa Valley wells.

  1. Ion mobility spectrometer with virtual aperture grid

    DOE Patents [OSTI]

    Pfeifer, Kent B. (Los Lunas, NM); Rumpf, Arthur N. (Albuquerque, NM)

    2010-11-23

    An ion mobility spectrometer does not require a physical aperture grid to prevent premature ion detector response. The last electrodes adjacent to the ion collector (typically the last four or five) have an electrode pitch that is less than the width of the ion swarm and each of the adjacent electrodes is connected to a source of free charge, thereby providing a virtual aperture grid at the end of the drift region that shields the ion collector from the mirror current of the approaching ion swarm. The virtual aperture grid is less complex in assembly and function and is less sensitive to vibrations than the physical aperture grid.

  2. Creating Mobile Emission Reduction Credits | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Creating Mobile Emission Reduction Credits Creating Mobile Emission Reduction Credits 2002 DEER Conference Presentation: Emission Credit Brokers 2002_deer_sloan.pdf (184.47 KB) More Documents & Publications Progress Update: Creating Mobile Emission Reduction Credits An Experimental Study of PM Emission Characteristics of Commercial Diesel Engine with Urea-SCR System Evaluation of NH3-SCR Catalyst Technology on a 250-kW Stationary Diesel Genset

  3. Using Mobile Applications to Generate Customer Demand | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Mobile Applications to Generate Customer Demand Using Mobile Applications to Generate Customer Demand Better Buildings Residential Network Peer Exchange Call Series: Using Mobile Applications to Generate Customer Demand, Call Slides and Discussion Summary, March 12, 2015. Call Slides and Discussion Summary (1.99 MB) More Documents & Publications Better Buildings Network View | October 2014 Swipe Left, Power Down: Using Interactive Media to Instill Behavior Change (301)

  4. Guidance for Deployment of Mobile Technologies for Nuclear Power Plant

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Field Workers | Department of Energy Guidance for Deployment of Mobile Technologies for Nuclear Power Plant Field Workers Guidance for Deployment of Mobile Technologies for Nuclear Power Plant Field Workers This report is a guidance document prepared for the benefit of commercial nuclear power plants' (NPPs) supporting organizations and personnel who are considering or undertaking deployment of mobile technology for the purpose of improving human performance and plant status control (PSC)

  5. Case Study: Mobile Photovoltaic System at Bechler Meadows Ranger Station,

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Yellowstone National Park | Department of Energy Mobile Photovoltaic System at Bechler Meadows Ranger Station, Yellowstone National Park Case Study: Mobile Photovoltaic System at Bechler Meadows Ranger Station, Yellowstone National Park Case study describes the performance of a mobile photovoltaic system installed in 2011 to provide power to Bechler Ranger Station in Yellowstone National Park, Wyoming. This small, remote outpost is not served by the electric utility grid and previously

  6. A Low-Cost Continuous Emissions Monitoring System for Mobile...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    A Low-Cost Continuous Emissions Monitoring System for Mobile and Stationary Engine SCRDPF ApplicationsData-Logger for Vehicle Data Acquisition This project describes a novel ...

  7. ARM: AOS: Scanning-Mobility Particle Sizer; temperature and RH...

    Office of Scientific and Technical Information (OSTI)

    AOS: Scanning-Mobility Particle Sizer; temperature and RH output Authors: Derek Hageman ; Bill Behrens ; Janek Uin ; Robert Bullard ; Cynthia Salwen ; Cynthia Salwen ; Annette ...

  8. Google Archives by Fiscal Year — Mobile Site

    Broader source: Energy.gov [DOE]

    From the EERE Web Statistics Archive: Corporate sites, retired Google Analytics profile for the Mobile site for fiscal year 2012-13.

  9. MHK Technologies/New Knowledge Wind and Wave Renewable Mobile...

    Open Energy Info (EERE)

    New Knowledge Wind and Wave Renewable Mobile Wind and Wave Power Plant Platform < MHK Technologies Jump to: navigation, search << Return to the MHK database homepage New Knowledge...

  10. Ultra-high Charge Carrier Mobility in an Organic Semiconductor...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    These measurements were performed independently both in Ume University, Sweden, and in Groningen University, Netherlands, and gave very similar values of mobility, with values as ...

  11. Influence of alkaline co-contaminants on technetium mobility...

    Office of Scientific and Technical Information (OSTI)

    Influence of alkaline co-contaminants on technetium mobility in vadose zone sediments Citation Details In-Document Search Title: Influence of alkaline co-contaminants on technetium ...

  12. A mobile-agent based wireless sensing network for structural...

    Office of Scientific and Technical Information (OSTI)

    for structural health monitoring applications Citation Details In-Document Search Title: A mobile-agent based wireless sensing network for structural health monitoring ...

  13. Mobile Truck Stop Electrification Locator Now Available - News...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    a billion gallons of fuel each year nationwide," said Wendy Dafoe, NREL manager of DOE's Alternative Fuels and Advanced ... of electrification sites, the mobile locator can ...

  14. Local Imaging of High Mobility Two-Dimensional Electron Systems...

    Office of Scientific and Technical Information (OSTI)

    Tunneling Microscopy Citation Details In-Document Search Title: Local Imaging of High Mobility Two-Dimensional Electron Systems with Virtual Scanning Tunneling Microscopy You ...

  15. EPA Climate Leaders Mobile Source Guidance | Open Energy Information

    Open Energy Info (EERE)

    EPA Climate Leaders Mobile Source Guidance AgencyCompany Organization: United States Environmental Protection Agency Sector: Energy Focus Area: Transportation Phase: Determine...

  16. Saudi Aramco Mobile Refinery Company (SAMREF) | Open Energy Informatio...

    Open Energy Info (EERE)

    Company (SAMREF) Name: Saudi Aramco Mobile Refinery Company (SAMREF) Address: P.O. Box 30078 Place: Yanbu, Saudi Arabia Sector: Oil and Gas Product: Crude Oil Refining Phone...

  17. ECIS, Boeing, Caltrans, and Others: Fuel-Cell-Powered Mobile...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Boeing, Caltrans, and Others: Fuel-Cell-Powered Mobile Lighting Applications - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate ...

  18. A mobile-agent based wireless sensing network for structural...

    Office of Scientific and Technical Information (OSTI)

    Furthermore, the mobile agent provides computational power to make near real-time assessments on the structural conditions. This paper will discuss such prototype systems, which ...

  19. A mobile-agent based wireless sensing network for structural...

    Office of Scientific and Technical Information (OSTI)

    Title: A mobile-agent based wireless sensing network for structural health monitoring ... Office of Scientific and Technical Information (OSTI) and is provided as a public service. ...

  20. Active microrheology in active matter systems: Mobility, intermittency...

    Office of Scientific and Technical Information (OSTI)

    Citation Details In-Document Search This content will become publicly available on March 24, 2016 Title: Active microrheology in active matter systems: Mobility, intermittency, and...

  1. Efficiency Nova Scotia Releases Energy Efficiency Mobile App...

    Energy Savers [EERE]

    Better Buildings Residential Network member Efficiency Nova Scotia recently released Spot it-an energy efficiency game app for mobile devices. The app features 13 levels where ...

  2. Energy Department Launches Mobile App for Energy Emergencies...

    Broader source: Energy.gov (indexed) [DOE]

    launched a mobile app called Lantern Live that helps consumers quickly find and share critical information about nearby gas stations and power outages during energy emergencies. ...

  3. SURFACTANT BASED ENHANCED OIL RECOVERY AND FOAM MOBILITY CONTROL...

    Office of Scientific and Technical Information (OSTI)

    Technical Report: SURFACTANT BASED ENHANCED OIL RECOVERY AND FOAM MOBILITY CONTROL Citation Details In-Document Search Title: SURFACTANT BASED ENHANCED OIL RECOVERY AND FOAM ...

  4. Mobility of Supercooled liquid Toluene, Ethylbenzene, and Benzene...

    Office of Scientific and Technical Information (OSTI)

    and Benzene near their Glass Transition Temperatures Investigated using Inert Gas Permeation Citation Details In-Document Search Title: Mobility of Supercooled liquid...

  5. Sandia Energy - Patent Awarded for the Fuel Cell Mobile Light

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Patent Awarded for the Fuel Cell Mobile Light Home Energy CRF Facilities Partnership News Energy Efficiency News & Events Systems Engineering Center for Infrastructure Research and...

  6. Slide 1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Condensation Nuclei Closure During CLASIC 2007 Jason Tomlinson and Don Collins PNNL Texas A&M University March 13 th , 2008 Acknowledgements: Ground crew, pilots, and flight planners. Work funded under DOE Grant #39495 * A major redesign of the Texas A&M Differential Mobility Analyzer/Tandem Differential Mobility Analyzer (DMA/TDMA) occurred in 2005/2006 - Simultaneous measurements of size distributions and the hygroscopic properties of the aerosol * For the CLASIC campaign, a Droplet

  7. Slide 1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Surface-based aerosol observations during ISDAC Don Collins - Texas A&M University Instrumentation Instrument Measurement Differential mobility analyzer (DMA) ↓ Cloud condensation nuclei counter (CCNc) Size-resolved activation efficiency at multiple S Tandem differential mobility analyzer (TDMA) Size-resolved hygroscopicity distributions Hygroscopic growth measurements April-average hygroscopicity distributions DMACCNc schematic Q s Q a Q sh Q ex P Flow Meter Filter e High Voltag

  8. Highly stable and efficient tandem organic light-emitting devices with intermediate connectors using lithium amide as n-type dopant

    SciTech Connect (OSTI)

    Zhou, Dong-Ying; Zu, Feng-Shuo; Shi, Xiao-Bo; Liao, Liang-Sheng E-mail: lsliao@suda.edu.cn; Zhang, Ying-Jie; Aziz, Hany E-mail: lsliao@suda.edu.cn

    2014-08-25

    In this work, we report thermally decomposable lithium amide (LiNH{sub 2}) feasible to function as an effective n-type dopant for intermediate connectors in tandem organic light-emitting devices (OLEDs). Metallic lithium, which is released from the decomposition process of LiNH{sub 2}, is proved by X-ray photoelectron spectroscopy and responsible for n-type electrical doping of electron transporting materials. We demonstrate that tandem OLEDs using LiNH{sub 2} and Cs{sub 2}CO{sub 3} as n-type dopants, respectively, give a comparable electroluminescence efficiency and, moreover, the device with LiNH{sub 2} has far longer operational lifetime. The results therefore highlight the significance of selecting suitable n-type dopant in intermediate connectors to fabricate high-stability tandem OLEDs.

  9. Development of a Mobile Ice Nucleus Counter

    SciTech Connect (OSTI)

    Kok, Gregory; Kulkarni, Gourihar

    2014-07-10

    An ice nucleus counter has been constructed. The instrument uses built-in refrigeration systems for wall cooling. A cascade refrigeration system will allow the cold wall to operate as low as -70 deg C, and a single stage system can operate the warm wall at -45 deg C. A unique optical particle counter has been constructed using polarization detection of the scattered light. This allows differentiation of the particles exiting the chamber to determine if they are ice or liquid.

  10. OPM Reservist Differential Briefing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Reservist Differential Briefing OPM Reservist Differential Briefing Uniformed Services Employment and Reemployment Rights Act Career, Seniority, Pay, and Benefits information OPM Reservist Differential Briefing (33.54 KB) Responsible Contacts Bruce Murray HR Policy Advisor E-mail bruce.murray@hq.doe.gov Phone 202-586-3372 More Documents & Publications OPM Briefing on Uniformed Services Employment and Reemployment Rights Act Training National Service Activation Checklist The Reemployment

  11. Manufacturing of High-Efficiency Bi-Facial Tandem Concentrator Solar Cells: February 20, 2009--August 20, 2010

    SciTech Connect (OSTI)

    Wojtczuk , S.

    2011-06-01

    Spire Semiconductor made concentrator photovoltaic (CPV) cells using a new bi-facial growth process and met both main program goals: a) 42.5% efficiency 500X (AM1.5D, 25C, 100mW/cm2); and b) Ready to supply at least 3MW/year of such cells at end of program. We explored a unique simple fabrication process to make a N/P 3-junction InGaP/GaAs/InGaAs tandem cells . First, the InGaAs bottom cell is grown on the back of a GaAs wafer. The wafers are then loaded into a cassette, spin-rinsed to remove particles, dipped in dilute NH4OH and spin-dried. The wafers are then removed from the cassette loaded the reactor for GaAs middle and InGaP top cell growth on the opposite wafer face (bi-facial growth). By making the epitaxial growth process a bit more complex, we are able to avoid more complex processing (such as large area wafer bonding or epitaxial liftoff) used in the inverted metamorphic (IMM) approach to make similar tandem stacks. We believe the yield is improved compared to an IMM process. After bi-facial epigrowth, standard III-V cell steps (back metal, photolithography for front grid, cap etch, AR coat, dice) are used in the remainder of the process.

  12. Outdoor Testing of GaInP2/GaAs Tandem Cells with Top Cell Thickness Varied

    SciTech Connect (OSTI)

    McMahon, W. E.; Emergy, K. E.; Friedman, D. J.; Ottoson, L.; Young, M. S.; Ward, J. S.; Kramer, C. M.; Duda, A.; Kurtz, S.

    2005-08-01

    In this study, we measure the performance of GaInP2/GaAs tandem cells under direct beam sunlight outdoors in order to quantify their sensitivity to both spectral variation and GaInP2 top-cell thickness. A set of cells with five different top-cell thicknesses was mounted on a two-axis tracker with the incident sunlight collimated to exclude all except the direct beam. Current-voltage (I-V) curves were taken throughout the course of several days, along with measurements of the direct solar spectrum. Our two major conclusions are: (1) GaInP2/GaAs tandem cells designed for either the ASTM G-173 direct (G-173D) spectrum or the "air mass 1.5 global" (AM1.5G) spectrum perform the best, and (2) cells can be characterized indoors and modeled using outdoor spectra with the same result. These results are equally valid for GaInP2/GaAs/Ge triple-junction cells.

  13. Time differentiated nuclear resonance spectroscopy coupled with...

    Office of Scientific and Technical Information (OSTI)

    heating in diamond anvil cells Citation Details In-Document Search Title: Time differentiated nuclear resonance spectroscopy coupled with pulsed laser heating in diamond anvil ...

  14. Checking out HUD`s proposed mobile home performance standards

    SciTech Connect (OSTI)

    Judkoff, R.

    1993-11-01

    This article evaluates both the performance of two mobile homes built to meet recently proposed federal energy performance standards and the standards themselves. Topics include test methods, results, thermal exposure infrared scan results; regulators, thermal characteristics of test homes, real life conditions, factory observations, the future of mobile home energy efficiency.

  15. SLS complementary logic devices with increase carrier mobility

    DOE Patents [OSTI]

    Chaffin, Roger J.; Osbourn, Gordon C.; Zipperian, Thomas E.

    1991-01-01

    In an electronic device comprising a semiconductor material and having at least one performance characteristic which is limited by the mobility of holes in the semiconductor material, said mobility being limited because of a valence band degeneracy among high-mobility and low-mobility energy levels accessible to said holes at the energy-momentum space maximum, an improvement is provided wherein the semiconductor material is a strained layer superlattice (SLS) whose layer compositions and layer thicknesses are selected so that the strain on the layers predominantly containing said at least one carrier type splits said degeneracy and modifies said energy levels around said energy-momentum space maximum in a manner whereby said limitation on the mobility of said holes is alleviated.

  16. SLS complementary logic devices with increase carrier mobility

    DOE Patents [OSTI]

    Chaffin, R.J.; Osbourn, G.C.; Zipperian, T.E.

    1991-07-09

    In an electronic device comprising a semiconductor material and having at least one performance characteristic which is limited by the mobility of holes in the semiconductor material, said mobility being limited because of a valence band degeneracy among high-mobility and low-mobility energy levels accessible to said holes at the energy-momentum space maximum, an improvement is provided wherein the semiconductor material is a strained layer superlattice (SLS) whose layer compositions and layer thicknesses are selected so that the strain on the layers predominantly containing said at least one carrier type splits said degeneracy and modifies said energy levels around said energy-momentum space maximum in a manner whereby said limitation on the mobility of said holes is alleviated. 5 figures.

  17. The relationship between polymer mobility and potential energy.

    SciTech Connect (OSTI)

    McCoy, John Dwane; Adolf, Douglas Brian; Budzien, Joanne L.

    2005-01-01

    The WLF equation is typically used to describe the dependence of polymer mobility on temperature at atmospheric pressure. Tests at different pressures would at least require different WLF parameterization. Completely different tests, for example, probing the temperature dependence of mobility at constant density, would require even greater modifications. By performing molecular dynamics simulations on simple chain molecules equilibrated at different thermodynamic states, we have shown that the mobility depends in a more general sense on the potential energy density of the system. That is, mobilities for any equilibrated state collapse onto one master curve when plotted against the potential energy density. Moreover, this relationship can be fit by either a 'generalized' WLF equation or by a power-law relationship observed in critical phenomena. When this mobility relationship is used within a rheologically simple, thermodynamically consistent, viscoelastic framework, quantitative agreement is seen between experimental data and theoretical predictions on a range of tests covering enthalpy relaxation to mechanical yield to physical aging.

  18. Method of assessing a lipid-related health risk based on ion mobility analysis of lipoproteins

    DOE Patents [OSTI]

    Benner, W. Henry; Krauss, Ronald M.; Blanche, Patricia J.

    2010-12-14

    A medical diagnostic method and instrumentation system for analyzing noncovalently bonded agglomerated biological particles is described. The method and system comprises: a method of preparation for the biological particles; an electrospray generator; an alpha particle radiation source; a differential mobility analyzer; a particle counter; and data acquisition and analysis means. The medical device is useful for the assessment of human diseases, such as cardiac disease risk and hyperlipidemia, by rapid quantitative analysis of lipoprotein fraction densities. Initially, purification procedures are described to reduce an initial blood sample to an analytical input to the instrument. The measured sizes from the analytical sample are correlated with densities, resulting in a spectrum of lipoprotein densities. The lipoprotein density distribution can then be used to characterize cardiac and other lipid-related health risks.

  19. Determining the risk of cardiovascular disease using ion mobility of lipoproteins

    DOE Patents [OSTI]

    Benner, W. Henry; Krauss, Ronald M.; Blanche, Patricia J.

    2010-05-11

    A medical diagnostic method and instrumentation system for analyzing noncovalently bonded agglomerated biological particles is described. The method and system comprises: a method of preparation for the biological particles; an electrospray generator; an alpha particle radiation source; a differential mobility analyzer; a particle counter; and data acquisition and analysis means. The medical device is useful for the assessment of human diseases, such as cardiac disease risk and hyperlipidemia, by rapid quantitative analysis of lipoprotein fraction densities. Initially, purification procedures are described to reduce an initial blood sample to an analytical input to the instrument. The measured sizes from the analytical sample are correlated with densities, resulting in a spectrum of lipoprotein densities. The lipoprotein density distribution can then be used to characterize cardiac and other lipid-related health risks.

  20. Simulation Model of Mobile Detection Systems

    SciTech Connect (OSTI)

    Edmunds, T; Faissol, D; Yao, Y

    2009-01-27

    In this paper, we consider a mobile source that we attempt to detect with man-portable, vehicle-mounted or boat-mounted radiation detectors. The source is assumed to transit an area populated with these mobile detectors, and the objective is to detect the source before it reaches a perimeter. We describe a simulation model developed to estimate the probability that one of the mobile detectors will come in to close proximity of the moving source and detect it. We illustrate with a maritime simulation example. Our simulation takes place in a 10 km by 5 km rectangular bay patrolled by boats equipped with 2-inch x 4-inch x 16-inch NaI detectors. Boats to be inspected enter the bay and randomly proceed to one of seven harbors on the shore. A source-bearing boat enters the mouth of the bay and proceeds to a pier on the opposite side. We wish to determine the probability that the source is detected and its range from target when detected. Patrol boats select the nearest in-bound boat for inspection and initiate an intercept course. Once within an operational range for the detection system, a detection algorithm is started. If the patrol boat confirms the source is not present, it selects the next nearest boat for inspection. Each run of the simulation ends either when a patrol successfully detects a source or when the source reaches its target. Several statistical detection algorithms have been implemented in the simulation model. First, a simple k-sigma algorithm, which alarms with the counts in a time window exceeds the mean background plus k times the standard deviation of background, is available to the user. The time window used is optimized with respect to the signal-to-background ratio for that range and relative speed. Second, a sequential probability ratio test [Wald 1947] is available, and configured in this simulation with a target false positive probability of 0.001 and false negative probability of 0.1. This test is utilized when the mobile detector maintains

  1. Segregated tandem filter for enhanced conversion efficiency in a thermophotovoltaic energy conversion system

    DOE Patents [OSTI]

    Brown, Edward J.; Baldasaro, Paul F.; Dziendziel, Randolph J.

    1997-01-01

    A filter system to transmit short wavelength radiation and reflect long wavelength radiation for a thermophotovoltaic energy conversion cell comprises an optically transparent substrate segregation layer with at least one coherent wavelength in optical thickness; a dielectric interference filter deposited on one side of the substrate segregation layer, the interference filter being disposed toward the source of radiation, the interference filter including a plurality of alternating layers of high and low optical index materials adapted to change from transmitting to reflecting at a nominal wavelength .lambda..sub.IF approximately equal to the bandgap wavelength .lambda..sub.g of the thermophotovoltaic cell, the interference filter being adapted to transmit incident radiation from about 0.5.lambda..sub.IF to .lambda..sub.IF and reflect from .lambda..sub.IF to about 2.lambda..sub.IF ; and a high mobility plasma filter deposited on the opposite side of the substrate segregation layer, the plasma filter being adapted to start to become reflecting at a wavelength of about 1.5.lambda..sub.IF.

  2. Segregated tandem filter for enhanced conversion efficiency in a thermophotovoltaic energy conversion system

    DOE Patents [OSTI]

    Brown, E.J.; Baldasaro, P.F.; Dziendziel, R.J.

    1997-12-23

    A filter system to transmit short wavelength radiation and reflect long wavelength radiation for a thermophotovoltaic energy conversion cell comprises an optically transparent substrate segregation layer with at least one coherent wavelength in optical thickness; a dielectric interference filter deposited on one side of the substrate segregation layer, the interference filter being disposed toward the source of radiation, the interference filter including a plurality of alternating layers of high and low optical index materials adapted to change from transmitting to reflecting at a nominal wavelength {lambda}{sub IF} approximately equal to the bandgap wavelength {lambda}{sub g} of the thermophotovoltaic cell, the interference filter being adapted to transmit incident radiation from about 0.5{lambda}{sub IF} to {lambda}{sub IF} and reflect from {lambda}{sub IF} to about 2{lambda}{sub IF}; and a high mobility plasma filter deposited on the opposite side of the substrate segregation layer, the plasma filter being adapted to start to become reflecting at a wavelength of about 1.5{lambda}{sub IF}. 10 figs.

  3. Segregated tandem filter for enhanced conversion efficiency in a thermophotovoltaic energy conversion system

    SciTech Connect (OSTI)

    Brown, E.J.; Baldasaro, P.F.; Dziendziel, R.J.

    1996-12-31

    A filter system to transmit short wavelength radiation and reflect long wavelength radiation for a thermophotovoltaic energy conversion cell comprises an optically transparent substrate segregation layer with at least one coherent wavelength in optical thickness; a dielectric interference filter deposited on one side of the substrate segregation layer, the interference filter being disposed toward the source of radiation, the interference filter including a plurality of alternating layers of high and low optical index materials adapted to change from transmitting to reflecting at a nominal wavelength {lambda}{sub IF} approximately equal to the bandgap wavelength {lambda}{sub g} of the thermophotovoltaic cell, the interference filter being adapted to transmit incident radiation from about 0.5{lambda}{sub IF} to {lambda}{sub IF} and reflect from {lambda}{sub IF} to about 2{lambda}{sub IF}; and a high mobility plasma filter deposited on the opposite side of the substrate segregation layer, the plasma filter being adapted to start to become reflecting at a wavelength of about 1.5{lambda}{sub IF}.

  4. Single shot spin readout with a cryogenic high-electron-mobility...

    Office of Scientific and Technical Information (OSTI)

    Single shot spin readout with a cryogenic high-electron-mobility transistor amplifier at ... high-electron-mobility transistor amplifier at sub-Kelvin temperatures We use a ...

  5. Reactive triblock polymers from tandem ring-opening polymerization for nanostructured vinyl thermosets

    SciTech Connect (OSTI)

    Amendt, Mark A.; Pitet, Louis M.; Moench, Sarah; Hillmyer, Marc A.

    2013-03-07

    Multiply functional hydroxyl telechelic poly(cyclooctene-s-5-norbornene-2-methylene methacrylate) was synthesized by ring opening metathesis (co)polymerization of cis-cyclooctene and 5-norbornene-2-methylene methacrylate using the second generation Grubbs catalyst in combination with a symmetric chain transfer agent bearing hydroxyl functionality. The resulting hydroxyl-telechelic polymer was used as a macroinitiator for the ring opening transesterification polymerization of d,l-lactide to form reactive poly(lactide)-b-poly(cyclooctene-s-5-norbornene-2-methylene methacrylate)-b-poly(lactide) triblock polymers. Subsequently, the triblocks were crosslinked by free radical copolymerization with several vinyl monomers including styrene, divinylbenzene, methyl methacrylate, and ethyleneglycol dimethacrylate. Certain conditions led to optically transparent thermosets with mesoscale phase separation as evidenced by small angle X-ray scattering, differential scanning calorimetry and transmission electron microscopy. Disordered, bicontinuous structures with nanoscopic domains were generated in several cases, rendering the samples attractive for size-selective membrane applications.

  6. Mobile autonomous robotic apparatus for radiologic characterization

    DOE Patents [OSTI]

    Dudar, A.M.; Ward, C.R.; Jones, J.D.; Mallet, W.R.; Harpring, L.J.; Collins, M.X.; Anderson, E.K.

    1999-08-10

    A mobile robotic system is described that conducts radiological surveys to map alpha, beta, and gamma radiation on surfaces in relatively level open areas or areas containing obstacles such as stored containers or hallways, equipment, walls and support columns. The invention incorporates improved radiation monitoring methods using multiple scintillation detectors, the use of laser scanners for maneuvering in open areas, ultrasound pulse generators and receptors for collision avoidance in limited space areas or hallways, methods to trigger visible alarms when radiation is detected, and methods to transmit location data for real-time reporting and mapping of radiation locations on computer monitors at a host station. A multitude of high performance scintillation detectors detect radiation while the on-board system controls the direction and speed of the robot due to pre-programmed paths. The operators may revise the preselected movements of the robotic system by ethernet communications to remonitor areas of radiation or to avoid walls, columns, equipment, or containers. The robotic system is capable of floor survey speeds of from 1/2-inch per second up to about 30 inches per second, while the on-board processor collects, stores, and transmits information for real-time mapping of radiation intensity and the locations of the radiation for real-time display on computer monitors at a central command console. 4 figs.

  7. Alternative non-CFC mobile air conditioning

    SciTech Connect (OSTI)

    Mei, V.C.; Chen, F.C.; Kyle, D.M.

    1992-09-01

    Concern about the destruction of the global environment by chlorofluorocarbon (CFC) fluids has become an impetus in the search for alternative, non-CFC refrigerants and cooling methods for mobile air conditioning (MAC). While some alternative refrigerants have been identified, they are not considered a lasting solution because of their high global warming potential, which could result in their eventual phaseout. In view of this dilemma, environmentally acceptable alternative cooling methods have become important. This report, therefore, is aimed mainly at the study of alternative automotive cooling methodologies, although it briefly discusses the current status of alternative refrigerants. The alternative MACs can be divided into work-actuated and heat-actuated systems. Work-actuated systems include conventional MAC, reversed Brayton air cycle, rotary vane compressor air cycle, Stirling cycle, thermoelectric (TE) cooling, etc. Heat-actuated MACs include metal hydride cooling, adsorption cooling, ejector cooling, absorption cycle, etc. While we are better experienced with some work-actuated cycle systems, heat-actuated cycle systems have a high potential for energy savings with possible waste heat applications. In this study, each altemative cooling method is discussed for its advantages and its limits.

  8. Advanced mobile networking, sensing, and controls.

    SciTech Connect (OSTI)

    Feddema, John Todd; Kilman, Dominique Marie; Byrne, Raymond Harry; Young, Joseph G.; Lewis, Christopher L.; Van Leeuwen, Brian P.; Robinett, Rush D. III; Harrington, John J.

    2005-03-01

    This report describes an integrated approach for designing communication, sensing, and control systems for mobile distributed systems. Graph theoretic methods are used to analyze the input/output reachability and structural controllability and observability of a decentralized system. Embedded in each network node, this analysis will automatically reconfigure an ad hoc communication network for the sensing and control task at hand. The graph analysis can also be used to create the optimal communication flow control based upon the spatial distribution of the network nodes. Edge coloring algorithms tell us that the minimum number of time slots in a planar network is equal to either the maximum number of adjacent nodes (or degree) of the undirected graph plus some small number. Therefore, the more spread out that the nodes are, the fewer number of time slots are needed for communication, and the smaller the latency between nodes. In a coupled system, this results in a more responsive sensor network and control system. Network protocols are developed to propagate this information, and distributed algorithms are developed to automatically adjust the number of time slots available for communication. These protocols and algorithms must be extremely efficient and only updated as network nodes move. In addition, queuing theory is used to analyze the delay characteristics of Carrier Sense Multiple Access (CSMA) networks. This report documents the analysis, simulation, and implementation of these algorithms performed under this Laboratory Directed Research and Development (LDRD) effort.

  9. Mobile worksystems for decontamination and dismantlement

    SciTech Connect (OSTI)

    Osborn, J.; Bares, L.C.; Thompson, B.R.

    1995-10-01

    Many DOE nuclear facilities have aged beyond their useful lifetimes. They need to be decommissioned in order to be safe for human presence in the short term, to eventually recover valuable materials they contain, and ultimately to be transitioned to alternative uses or green field conditions. Decontamination and dismantlement are broad classes of activities that will enable these changes to occur. Most of these facilities - uranium enrichment plants, weapons assembly plants, research and production reactors, and fuel recycling facilities - are dormant, though periodic inspection, surveillance and maintenance activities within them are on-going. DOE estimates that there are over 5000 buildings that require deactivation to reduce the costs of performing such work with manual labor. In the long term, 1200 buildings will be decommissioned, and millions of metric tons of metal and concrete will have to be recycled or disposed of. The magnitude of the problem calls for new approaches that are far more cost effective than currently available techniques. This paper describes a mobile workstation termed ROSIE, which provides remote work capabilities for D&D activities.

  10. Pathogenicity island mobility and gene content.

    SciTech Connect (OSTI)

    Williams, Kelly Porter

    2013-10-01

    Key goals towards national biosecurity include methods for analyzing pathogens, predicting their emergence, and developing countermeasures. These goals are served by studying bacterial genes that promote pathogenicity and the pathogenicity islands that mobilize them. Cyberinfrastructure promoting an island database advances this field and enables deeper bioinformatic analysis that may identify novel pathogenicity genes. New automated methods and rich visualizations were developed for identifying pathogenicity islands, based on the principle that islands occur sporadically among closely related strains. The chromosomally-ordered pan-genome organizes all genes from a clade of strains; gaps in this visualization indicate islands, and decorations of the gene matrix facilitate exploration of island gene functions. A %E2%80%9Clearned phyloblocks%E2%80%9D method was developed for automated island identification, that trains on the phylogenetic patterns of islands identified by other methods. Learned phyloblocks better defined termini of previously identified islands in multidrug-resistant Klebsiella pneumoniae ATCC BAA-2146, and found its only antibiotic resistance island.

  11. Mobile autonomous robotic apparatus for radiologic characterization

    DOE Patents [OSTI]

    Dudar, Aed M.; Ward, Clyde R.; Jones, Joel D.; Mallet, William R.; Harpring, Larry J.; Collins, Montenius X.; Anderson, Erin K.

    1999-01-01

    A mobile robotic system that conducts radiological surveys to map alpha, beta, and gamma radiation on surfaces in relatively level open areas or areas containing obstacles such as stored containers or hallways, equipment, walls and support columns. The invention incorporates improved radiation monitoring methods using multiple scintillation detectors, the use of laser scanners for maneuvering in open areas, ultrasound pulse generators and receptors for collision avoidance in limited space areas or hallways, methods to trigger visible alarms when radiation is detected, and methods to transmit location data for real-time reporting and mapping of radiation locations on computer monitors at a host station. A multitude of high performance scintillation detectors detect radiation while the on-board system controls the direction and speed of the robot due to pre-programmed paths. The operators may revise the preselected movements of the robotic system by ethernet communications to remonitor areas of radiation or to avoid walls, columns, equipment, or containers. The robotic system is capable of floor survey speeds of from 1/2-inch per second up to about 30 inches per second, while the on-board processor collects, stores, and transmits information for real-time mapping of radiation intensity and the locations of the radiation for real-time display on computer monitors at a central command console.

  12. A very thin havar film vacuum window for heavy ions to perform radiobiology studies at the BNL Tandem

    SciTech Connect (OSTI)

    Thieberger, P.; Abendroth, H.; Alessi, J.; Cannizzo, L.; Carlson, C.; Gustavsson, A.; Minty, M.; Snydstrup, L.

    2011-03-28

    Heavy ion beams from the BNL Tandem Van de Graaff accelerators will be made available for radiobiology studies on cell cultures. Beam energy losses need to be minimized both in the vacuum window and in the air in order to achieve the ranges required for the cells to be studied. This is particularly challenging for ions heavier than iron. The design is presented of a 0.4-inch diameter Havar film window that will satisfy these requirements. Films as thin as 80 microinches were successfully pressure tested. The final thickness to be used may be slightly larger to help in achieving pin hole free windows. We discuss design considerations and present pressure and vacuum test results as well as tests with heavy ion beams.

  13. Monolithic, multi-bandgap, tandem, ultra-thin, strain-counterbalanced, photovoltaic energy converters with optimal subcell bandgaps

    DOE Patents [OSTI]

    Wanlass, Mark W.; Mascarenhas, Angelo

    2012-05-08

    Modeling a monolithic, multi-bandgap, tandem, solar photovoltaic converter or thermophotovoltaic converter by constraining the bandgap value for the bottom subcell to no less than a particular value produces an optimum combination of subcell bandgaps that provide theoretical energy conversion efficiencies nearly as good as unconstrained maximum theoretical conversion efficiency models, but which are more conducive to actual fabrication to achieve such conversion efficiencies than unconstrained model optimum bandgap combinations. Achieving such constrained or unconstrained optimum bandgap combinations includes growth of a graded layer transition from larger lattice constant on the parent substrate to a smaller lattice constant to accommodate higher bandgap upper subcells and at least one graded layer that transitions back to a larger lattice constant to accommodate lower bandgap lower subcells and to counter-strain the epistructure to mitigate epistructure bowing.

  14. Impact of sub-cell internal luminescence yields on energy conversion efficiencies of tandem solar cells: A design principle

    SciTech Connect (OSTI)

    Zhu, Lin Kim, Changsu; Yoshita, Masahiro; Chen, Shaoqiang; Sato, Shintaroh; Mochizuki, Toshimitsu; Akiyama, Hidefumi; Kanemitsu, Yoshihiko

    2014-01-20

    To develop a realistic design principle, we calculated the maximum conversion efficiency ?{sub sc} and optimized sub-cell band-gap energies E{sub g} in double-junction tandem solar cells via a detailed-balance theory, paying particular attention to their dependence on internal luminescence quantum yields y{sub int} of the top and bottom sub-cell materials. A strong drop in the maximum ?{sub sc} occurs when y{sub int} slightly drops from 1 to 0.9, where the drop in y{sub int} of the bottom cell causes a stronger effect than that of the top cell. For low values of y{sub int}, the maximum ?{sub sc} has a simple logarithmic dependence on the geometric mean of the two sub-cells'y{sub int}.

  15. De novo tandem duplication of chromosome segement 22q11-q12: Clinical, cytogenetic, and molecular characterization

    SciTech Connect (OSTI)

    Lindsay, E.A.; Shaffer, L.G.; Carrozzo, R.

    1995-04-10

    We report on a case of duplication of the segment 22q11-q12 due to a de novo duplication. Molecular cytogenetics studies demonstrated this to be a tandem duplication, flanked proximally by the marker D22Z4, a centromeric alpha satellite DNA repeat, and distally by D22S260, an anonymous DNA marker proximal to the Ewing sarcoma breakpoint. The segment includes the regions responsible for the {open_quotes}cat-eye{close_quotes}, Di George, and velo-cardio-facial syndromes and extends distal to the breakpoint cluster region (BCR). The clinical picture is dominated by the cardiac defects and includes findings reminiscent of {open_quotes}cat-eye{close_quotes} syndrome. These findings reinforce the hypothesis that the proximal 22q region contains dosage-sensitive genes involved in development. 20 refs., 3 figs.

  16. TMRBAR: a code to calculate plasma parameters for tandem-mirror reactors operating in the MARS mode

    SciTech Connect (OSTI)

    Campbell, R.B.

    1983-08-30

    The purpose of this report is to document the plasma power balance model currently used by LLNL to calculate steady state operating points for tandem mirror reactors. The code developed from this model, TMRBAR, has been used to predict the performance and define supplementary heating requirements for drivers used in the Mirror Advanced Reactor Study (MARS) and for the Fusion Power Demonstration (FPD) study. The equations solved included particle and energy balance for central cell and end cell species, quasineutrality at several cardinal points in the end cell region, as well as calculations of volumes, densities and average energies based on given constraints of beta profiles and fusion power output. Alpha particle ash is treated self-consistently, but no other impurity species is treated.

  17. Development of polarization-controlled multi-pass Thomson scattering system in the GAMMA 10 tandem mirror

    SciTech Connect (OSTI)

    Yoshikawa, M.; Morimoto, M.; Shima, Y.; Kohagura, J.; Sakamoto, M.; Nakashima, Y.; Imai, T. [Plasma Research Center, University of Tsukuba, 1-1-1 Tennodai, Tsukuba, Ibaraki 305-8577 (Japan); Yasuhara, R.; Yamada, I.; Kawahata, K.; Funaba, H. [National Institute for Fusion Science, 322-6 Oroshi-cho, Toki, Gifu 509-5292 (Japan); Minami, T. [Institute of Advanced Energy, Kyoto University, Gokasho, Uji, Kyoto 611-0011 (Japan)

    2012-10-15

    In the GAMMA 10 tandem mirror, the typical electron density is comparable to that of the peripheral plasma of torus-type fusion devices. Therefore, an effective method to increase Thomson scattering (TS) signals is required in order to improve signal quality. In GAMMA 10, the yttrium-aluminum-garnet (YAG)-TS system comprises a laser, incident optics, light collection optics, signal detection electronics, and a data recording system. We have been developing a multi-pass TS method for a polarization-based system based on the GAMMA 10 YAG TS. To evaluate the effectiveness of the polarization-based configuration, the multi-pass system was installed in the GAMMA 10 YAG-TS system, which is capable of double-pass scattering. We carried out a Rayleigh scattering experiment and applied this double-pass scattering system to the GAMMA 10 plasma. The integrated scattering signal was made about twice as large by the double-pass system.

  18. Mobile Torrefaction Machine" James, Joseph J. [President, ATP...

    Office of Scientific and Technical Information (OSTI)

    State University (NCSU), which ATP has licensed, could be feasibly deployed in a mobile unit. The study adds to the area investigated, by having ATP's STTR Phase I team give...

  19. Mobility of Source Zone Heavy Metals and Radionuclides: The...

    Office of Scientific and Technical Information (OSTI)

    ... Field, E.K. , P. Haun, R. Gerlach, B.M. Peyton, W.A. Apel, and B.D. Lee (2006): The Influence of Cellulose Utilization on Metal and Radionuclide Mobility and Reduction. ...

  20. ARM Mobile Facility - Design and Schedule for Integration

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mobile Facility - Design and Schedule for Integration K. B. Widener Pacific Northwest ... The design phase for developing the AMF has begun. A design review was held for the AMF in ...

  1. ARM - Field Campaign - Application of the ARM Mobile Facility...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the ARM Mobile Facility (AMF) to Study the Aerosol Indirect Effects in China Campaign Links China Website ARM Data Discovery Browse Data Comments? We would love to hear from you ...

  2. Raymond Burns > Product Research Technologist - Exxon Mobile > Center

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Alumni > The Energy Materials Center at Cornell Raymond Burns Product Research Technologist - Exxon Mobile raymond.burns@gmail.com Formerly a member of the DiSalvo Group, Ray earned his PhD in August 2013

  3. Sandia Energy - Fuel-Cell-Powered Mobile Lights Tested, Proven...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and in other applications. (Photo by Dino Vournas) Mobile lighting systems powered by hydrogen (H2) fuel cells are cleaner, quieter, and now have a proven track record in...

  4. Mobility of charge carriers in porous silicon layers

    SciTech Connect (OSTI)

    Forsh, P. A. Martyshov, M. N.; Latysheva, A. P.; Vorontsov, A. S.; Timoshenko, V. Yu.; Kashkarov, P. K.

    2008-12-15

    The (conduction) mobility of majority charge carriers in porous silicon layers of the n and p types is estimated by joint measurements of electrical conductivity and free charge carrier concentration, which is determined from IR absorption spectra. Adsorption of donor and acceptor molecules leading to a change in local electric fields in the structure is used to identify the processes controlling the mobility in porous silicon. It is found that adsorption of acceptor and donor molecules at porous silicon of the p and n types, respectively, leads to a strong increase in electrical conductivity, which is associated with an increase in the concentration of free carrier as well as in their mobility. The increase in the mobility of charge carriers as a result of adsorption indicates the key role of potential barriers at the boundaries of silicon nanocrystals and may be due to a decrease in the barrier height as a result of adsorption.

  5. MOBILE6 Vehicle Emission Modeling Software | Open Energy Information

    Open Energy Info (EERE)

    tools User Interface: Desktop Application Website: www.epa.govomsm6.htm Cost: Free References: http:www.epa.govomsm6.htm MOBILE6 is an emission factor model for...

  6. Mobility of Source Zone Heavy Metals and Radionuclides: The Mixed...

    Office of Scientific and Technical Information (OSTI)

    Various U. S. Department of Energy (DOE) low and medium-level radioactive waste sites ... and other contaminants can be mobilized by infiltration of water into waste storage sites. ...

  7. Efficiency Nova Scotia Releases Energy Efficiency Mobile App

    Broader source: Energy.gov [DOE]

    Better Buildings Residential Network member Efficiency Nova Scotia recently released Spot it!—an energy efficiency game app for mobile devices. The app features 13 levels where players are...

  8. LONG-TERM COLLOID MOBILIZATION AND COLLOID-FACILITATED TRANSPORT...

    Office of Scientific and Technical Information (OSTI)

    LONG-TERM COLLOID MOBILIZATION AND COLLOID-FACILITATED TRANSPORT OF RADIONUCLIDES IN A SEMI-ARID VADOSE ZONE Citation Details In-Document Search Title: LONG-TERM COLLOID ...

  9. Local Imaging of High Mobility Two-Dimensional Electron Systems...

    Office of Scientific and Technical Information (OSTI)

    Dept. SLAC ; Pfeiffer, L.N. ; West, K.W. ; Princeton U., Elect. Engion. Dept. ; Goldhaber-Gordon, D. ; Stanford U., Phys.Dept.TITLELocal Imaging of High Mobility Two-Dimensional ...

  10. 3D Printed Microscope for Mobile Devices that Cost Pennies

    ScienceCinema (OSTI)

    Erikson, Rebecca; Baird, Cheryl; Hutchinson, Janine

    2015-06-23

    Scientists at PNNL have designed a 3D-printable microscope for mobile devices using pennies worth of plastic and glass materials. The microscope has a wide range of uses, from education to in-the-field science.

  11. 3D Printed Microscope for Mobile Devices that Cost Pennies

    SciTech Connect (OSTI)

    Erikson, Rebecca; Baird, Cheryl; Hutchinson, Janine

    2014-09-15

    Scientists at PNNL have designed a 3D-printable microscope for mobile devices using pennies worth of plastic and glass materials. The microscope has a wide range of uses, from education to in-the-field science.

  12. Atmospheric process evaluation of mobile source emissions

    SciTech Connect (OSTI)

    1995-07-01

    During the past two decades there has been a considerable effort in the US to develop and introduce an alternative to the use of gasoline and conventional diesel fuel for transportation. The primary motives for this effort have been twofold: energy security and improvement in air quality, most notably ozone, or smog. The anticipated improvement in air quality is associated with a decrease in the atmospheric reactivity, and sometimes a decrease in the mass emission rate, of the organic gas and NO{sub x} emissions from alternative fuels when compared to conventional transportation fuels. Quantification of these air quality impacts is a prerequisite to decisions on adopting alternative fuels. The purpose of this report is to present a critical review of the procedures and data base used to assess the impact on ambient air quality of mobile source emissions from alternative and conventional transportation fuels and to make recommendations as to how this process can be improved. Alternative transportation fuels are defined as methanol, ethanol, CNG, LPG, and reformulated gasoline. Most of the discussion centers on light-duty AFVs operating on these fuels. Other advanced transportation technologies and fuels such as hydrogen, electric vehicles, and fuel cells, will not be discussed. However, the issues raised herein can also be applied to these technologies and other classes of vehicles, such as heavy-duty diesels (HDDs). An evaluation of the overall impact of AFVs on society requires consideration of a number of complex issues. It involves the development of new vehicle technology associated with engines, fuel systems, and emission control technology; the implementation of the necessary fuel infrastructure; and an appropriate understanding of the economic, health, safety, and environmental impacts associated with the use of these fuels. This report addresses the steps necessary to properly evaluate the impact of AFVs on ozone air quality.

  13. Mobile Climate Monitoring Facility to Sample Skies in Africa | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Mobile Climate Monitoring Facility to Sample Skies in Africa Mobile Climate Monitoring Facility to Sample Skies in Africa January 18, 2006 - 10:47am Addthis WASHINGTON, D.C. -- The U.S. Department of Energy's Atmospheric Radiation Measurement (ARM) Program is placing a new, portable atmospheric laboratory with sophisticated instruments and data systems in Niger, Africa, to gain a better understanding of the potential impacts of Saharan dust on global climate. Dust from Africa's

  14. International Energy Agency Bioenergy Webinar: Mobilizing Sustainable Bioenergy Supply Chains

    Broader source: Energy.gov [DOE]

    International Energy Agency (IEA) Bioenergy program will be hosting a webinar on Feb. 25, 2016 to present the findings of their “Mobilize Sustainable Bioenergy Supply Chains” project. Over the last three years, researchers have collaborated to examine the prospects for large-scale mobilization of bioenergy resources across the globe. Members of Bioenergy Technologies Office staff support the research and activities and IEA Bioenergy. Email to register to attend the webinar.

  15. EPA Mobile Source Rule Update | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Mobile Source Rule Update EPA Mobile Source Rule Update 2003 DEER Conference Presentation: U.S. Department of Energy FreedomCAR and Vehicle Technologies Program deer_2003_charmley.pdf (847.05 KB) More Documents & Publications EPA Diesel Update Technical Challenges and Opportunities Light-Duty Diesel Engines in North America Development on simultaneous reduction system of NOx and PM from a diesel engine

  16. NREL: Technology Deployment - Mobile App Puts Alternative Fueling Station

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Locations in the Palm of Your Hand Mobile App Puts Alternative Fueling Station Locations in the Palm of Your Hand News NREL Developed Mobile App for Alternative Fueling Station Locations Released Energy Department Launches Alternative Fueling Station Locator App Using the Enhanced Alternative Fueling Station Locator Alternative Fueling Stations Database Sponsors U.S. Department of Energy Related Stories Remote Shading Tool Has Potential to Reduce Solar Soft Costs by 17 Cents/Watt Contact

  17. DOE - Office of Legacy Management -- Mobil Oil Corp - VA 01

    Office of Legacy Management (LM)

    Mobil Oil Corp - VA 01 FUSRAP Considered Sites Site: Mobil Oil Corp. (VA.01 ) Eliminated from further consideration under FUSRAP Designated Name: Not Designated Alternate Name: Virginia-Carolina Chemical Corporation VA.01-1 Location: 818 Perry Street , Richmond , Virginia VA.01-1 Evaluation Year: Circa 1987 VA.01-2 VA.01-3 Site Operations: Research/Development to recover Uranium as a byproduct of phosphate production; preparatory process for pilot plant scale operation at Nichols, Florida.

  18. Atmospheric Radiation Measurement Radiative Atmospheric Divergence using ARM Mobile

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Radiative Atmospheric Divergence using ARM Mobile Facility, GERB, and AMMA Stations (RADAGAST) Beginning in January 2006, the ARM Mobile Facility (AMF) began supporting RADAGAST to provide the first well-sampled direct esti- mates of the energy balance across the atmosphere. The experiment is part of an ongoing international study of the West African monsoon system and Saharan dust storms. Stationed outside the Niger Meteo- rological Office at the Niamey International Airport, the AMF is located

  19. Aspects of Exxon Mobil Corporation's Acquisition of XTO Energy Inc

    Reports and Publications (EIA)

    2009-01-01

    A summary presentation to inform discussion of the recently announced acquisition of XTO Energy Inc. by Exxon Mobil Corporation, a transaction which is reportedly $41 billion in value. "Aspects of Exxon Mobil Corporation's Acquisition of XTO Energy Inc" presents non-proprietary company-level oil and gas production and reserve data and the relevant U.S. aggregate data published by the Energy Information Administration.

  20. Come to Bioenergy 2016 to Support Mobilizing the Bioeconomy through

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Innovation | Department of Energy Come to Bioenergy 2016 to Support Mobilizing the Bioeconomy through Innovation Come to Bioenergy 2016 to Support Mobilizing the Bioeconomy through Innovation July 6, 2016 - 2:30pm Addthis Jonathan Male Jonathan Male Director, Bioenergy Technologies Office This summer, we're bringing together bioenergy experts and stakeholders to collaborate on some of the most relevant, current, and critical issues to the growth and success of the bioeconomy today. We'll be

  1. Superconductive microstrip exhibiting negative differential resistivity

    DOE Patents [OSTI]

    Huebener, R.P.; Gallus, D.E.

    1975-10-28

    A device capable of exhibiting negative differential electrical resistivity over a range of values of current and voltage is formed by vapor- depositing a thin layer of a material capable of exhibiting superconductivity on an insulating substrate, establishing electrical connections at opposite ends of the deposited strip, and cooling the alloy into its superconducting range. The device will exhibit negative differential resistivity when biased in the current- induced resistive state.

  2. Low-voltage differentially-signaled modulators

    SciTech Connect (OSTI)

    Zortman, William A.; Lentine, Anthony L.; Hsia, Alexander H.; Watts, Michael R.

    2015-09-08

    Photonic modulators and methods of modulating an input optical signal are provided. A photonic modulator includes at least one modulator section and differential drive circuitry. The at least one modulator section includes a P-type layer and an N-type layer forming a PN junction in the modulator section. The differential drive circuitry is electrically coupled to the P-type layer and the N-type layer of the at least one modulator section.

  3. Differential Impact of [beta] and [gamma] Residue Preorganization...

    Office of Scientific and Technical Information (OSTI)

    Differential Impact of beta and gamma Residue Preorganization on alphabetagamma-Peptide Helix Stability in Water Citation Details In-Document Search Title: Differential ...

  4. The differential algebra based multiple level fast multipole...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: The differential algebra based multiple level fast multipole algorithm ... Title: The differential algebra based multiple level fast multipole algorithm for 3D space ...

  5. Tracking Living Cells as They Differentiate in Real Time

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tracking Living Cells as They Differentiate in Real Time Tracking Living Cells as They Differentiate in Real Time Print Thursday, 27 September 2012 00:00 Protein phosphorylation ...

  6. Mobile Munitions Assessment System Field Capabilities

    SciTech Connect (OSTI)

    A. M. Snyder; D. A. Verrill; K. D. Watts

    1999-05-27

    The US has developed, stored, tested, and conducted disposal operations on various forms of chemical munitions for several decades. The remnants of these activities have resulted in the presence of suspect CWM at more than 200 sites in the US, the District of Columbia, and the US Virgin Islands. An advanced Mobile Munitions Assessment System (Phase II MMAS) has been designed, fabricated, assembled, and tested by the Idaho National Engineering and Environmental Laboratory under contract to the US Army's Project Manager for Non-Stockpile Chemical Materiel for use in the assessment and characterization of ''non-stockpile'' chemical warfare materiel (CWM). The Phase II MMAS meets the immediate need to augment response equipment currently used by the US Army with a system that includes state-of-the-art assessment equipment and advanced sensors. The Phase II MMAS will be used for response to known storage and remediation sites. This system is designed to identify the munition type; evaluate the condition of the CWM; evaluate the environmental conditions in the vicinity of the CWM; determine if fuzes, bursters, or safety and arming devices are in place; identify the chemical fill; provide other data (e.g., meteorological data) necessary for assessing the risk associated with handling, transporting, and disposing of CWM; and record the data on a dedicated computer system. The Phase II MMAS is capable of over-the-road travel and air transport to any site for conducting rigorous assessments of suspect CWM. The Phase II MMAS utilizes a specially-designed commercial motor home to provide a means to transport an interactive network of non-intrusive characterization and assessment equipment. The assessment equipment includes radiography systems, a gamma densitometer system, a Portable Isotopic Neutron Spectroscopy (PINS) system, a Secondary Ion Mass Spectroscopy (SIMS) system, air monitoring equipment (i.e., M-90s and a field ion spectroscopy system), and a phase determination

  7. Energy Auditor - Single Family 2.0: Mobile Home Assessment | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Mobile Home Assessment Energy Auditor - Single Family 2.0: Mobile Home Assessment Mobile Home Assessment - Complete (5.85 MB) Lesson Plan: Mobile Home Assessment (310.8 KB) PowerPoint: Mobile Home Assessment (5.69 MB) More Documents & Publications Weatherization Installer/Technician Fundamentals 2.0 - Mechanical Systems and Improve Duct Systems Energy Auditor - Single Family 2.0: Building Shell Retrofit Strategies Energy Auditor - Single Family 2.0: HVAC Distribution System

  8. V-235: Cisco Mobility Services Engine Configuration Error Lets Remote Users

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Login Anonymously | Department of Energy 5: Cisco Mobility Services Engine Configuration Error Lets Remote Users Login Anonymously V-235: Cisco Mobility Services Engine Configuration Error Lets Remote Users Login Anonymously September 5, 2013 - 12:33am Addthis PROBLEM: A vulnerability was reported in Cisco Mobility Services Engine. A remote user can login anonymously. PLATFORM: Cisco Mobility Services Engine ABSTRACT: A vulnerability in Cisco Mobility Services Engine could allow an

  9. Dual mode ion mobility spectrometer and method for ion mobility spectrometry

    DOE Patents [OSTI]

    Scott, Jill R [Idaho Falls, ID; Dahl, David A [Idaho Falls, ID; Miller, Carla J [Idaho Falls, ID; Tremblay, Paul L [Idaho Falls, ID; McJunkin, Timothy R [Idaho Falls, ID

    2007-08-21

    Ion mobility spectrometer apparatus may include an ion interface that is operable to hold positive and negative ions and to simultaneously release positive and negative ions through respective positive and negative ion ports. A first drift chamber is operatively associated with the positive ion port of the ion interface and encloses an electric field therein. A first ion detector operatively associated with the first drift chamber detects positive ions from the first drift chamber. A second drift chamber is operatively associated with the negative ion port of the ion interface and encloses an electric field therein. A second ion detector operatively associated with the second drift chamber detects negative ions from said second drift chamber.

  10. Troglitazone induces differentiation in Trypanosoma brucei

    SciTech Connect (OSTI)

    Denninger, Viola; Figarella, Katherine; Schoenfeld, Caroline; Brems, Stefanie; Busold, Christian; Lang, Florian; Hoheisel, Joerg; Duszenko, Michael . E-mail: michael.duszenko@uni-tuebingen.de

    2007-05-15

    Trypanosoma brucei, a protozoan parasite causing sleeping sickness, is transmitted by the tsetse fly and undergoes a complex lifecycle including several defined stages within the insect vector and its mammalian host. In the latter, differentiation from the long slender to the short stumpy form is induced by a yet unknown factor of trypanosomal origin. Here we describe that some thiazolidinediones are also able to induce differentiation. In higher eukaryotes, thiazolidinediones are involved in metabolism and differentiation processes mainly by binding to the intracellular receptor peroxisome proliferator activated receptor {gamma}. Our studies focus on the effects of troglitazone on bloodstream form trypanosomes. Differentiation was monitored using mitochondrial markers (membrane potential, succinate dehydrogenase activity, inhibition of oxygen uptake by KCN, amount of cytochrome transcripts), morphological changes (Transmission EM and light microscopy), and transformation experiments (loss of the Variant Surface Glycoprotein coat and increase of dihydroliponamide dehydrogenase activity). To further investigate the mechanisms responsible for these changes, microarray analyses were performed, showing an upregulation of expression site associated gene 8 (ESAG8), a potential differentiation regulator.

  11. Efficient enhancement of hydrogen production by Ag/Cu{sub 2}O/ZnO tandem triple-junction photoelectrochemical cell

    SciTech Connect (OSTI)

    Liu, Ying; Ren, Feng Chen, Chao; Liu, Chang; Xing, Zhuo; Liu, Dan; Xiao, Xiangheng; Wu, Wei; Zheng, Xudong; Liu, Yichao; Jiang, Changzhong; Shen, Shaohua; Fu, Yanming

    2015-03-23

    Highly efficient semiconductor photoelectrodes for solar hydrogen production through photocatalytic water splitting are a promising and challenge solution to solve the energy problems. In this work, Ag/Cu{sub 2}O/ZnO tandem triple-junction photoelectrode was designed and prepared. An increase of 11 times of photocurrent is achieved in the Ag/Cu{sub 2}O/ZnO photoelectrode comparing to that of the Cu{sub 2}O film. The high performance of the Ag/Cu{sub 2}O/ZnO film is due to the optimized design of the tandem triple-junction structure, where the localized surface Plasmon resonance of Ag and the hetero-junctions efficiently absorb solar energy, produce, and separate electron-hole pairs in the photocathode.

  12. Generating end plug potentials in tandem mirror plasma confinement by heating thermal particles so as to escape low density end stoppering plasmas

    DOE Patents [OSTI]

    Baldwin, David E.; Logan, B. Grant

    1981-01-01

    The invention provides a method and apparatus for raising the potential of a magnetic mirror cell by pumping charged particles of the opposite sign of the potential desired out of the mirror cell through excitation, with the pumping being done by an externally imposed field at the bounce frequency of the above charged particles. These pumped simple mirror cells then provide end stoppering for a center mirror cell for the tandem mirror plasma confinement apparatus. For the substantially complete pumping case, the end plugs of a tandem mirror can be up to two orders of magnitude lower in density for confining a given center mirror cell plasma than in the case of end plugs without pumping. As a result the decrease in recirculating power required to keep the system going, the technological state of the art required, and the capital cost are all greatly lowered.

  13. Generating end plug potentials in tandem mirror plasma confinement by heating thermal particles so as to escape low density end stoppering plasmas

    DOE Patents [OSTI]

    Baldwin, D.E.; Logan, B.G.

    The invention provides a method and apparatus for raising the potential of a magnetic mirror cell by pumping charged particles of the opposite sign of the potential desired out of the mirror cell through excitation, with the pumping being done by an externally imposed field at the bounce frequence of the above charged particles. These pumped simple mirror cells then provide end stoppering for a center mirror cell for the tandem mirror plasma confinement apparatus. For the substantially complete pumping case, the end plugs of a tandem mirror can be up to two orders of magnitude lower in density for confining a given center mirror cell plasma than in the case of end plugs without pumping. As a result the decrease in recirculating power required to keep the system going, the technical state of the art required, and the capital cost are all greatly lowered.

  14. NREL Develops ZnSiP2 for Silicon-Based Tandem Solar Cells (Fact Sheet), NREL Highlights in Research & Development, NREL (National Renewable Energy Laboratory)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Combining an Earth-abundant chalcopyrite with a silicon layer could significantly boost conversion efficiency above that of single-junction silicon solar cells. A current technological challenge in photovoltaics (PV) is to implement a lattice-matched, optically efficient material to be used in conjunction with silicon for tandem PV cells. III-V materials currently hold the world-record conver- sion efficiencies for both single- and multijunction cells. Researchers at the National Renewable

  15. Are the Radical Centers in Peptide Radical Cations Mobile? The Generation, Tautomerism, and Dissociation of Isomeric α-Carbon-Centered Triglycine Radical Cations in the Gas Phase

    SciTech Connect (OSTI)

    Chu, Ivan K.; Zhao, Junfang; Xu, Minjie; Siu, Shiu On; Hopkinson, Alan C.; Siu , K W Michael

    2008-05-31

    The mobility of the radical center in three isomeric triglycine radical cationss[G•GG]+, [GG•G]+, and [GGG•]+shas been investigated theoretically via density functional theory (DFT) and experimentally via tandem mass spectrometry. These radical cations were generated by collision-induced dissociations (CIDs) of Cu(II)-containing ternary complexes that contain the tripeptides YGG, GYG, and GGY, respectively (G and Y are the glycine and tyrosine residues, respectively). Dissociative electron transfer within the complexes led to observation of [Y•GG]+, [GY•G]+, and [GGY•]+; CID resulted in cleavage of the tyrosine side chain as p-quinomethide, yielding [G•GG]+, [GG•G]+, and [GGG•]+, respectively. Interconversions between these isomeric triglycine radical cations have relatively high barriers (g44.7 kcal/mol), in support of the thesis that isomerically pure [G•GG]+, [GG•G]+, and [GGG•]+ can be experimentally produced. This is to be contrasted with barriers < 17 kcal/mol that were encountered in the tautomerism of protonated triglycine [Rodriquez C. F. et al. J. Am. Chem. Soc. 2001, 123, 3006-3012]. The CID spectra of [G•GG]+, [GG•G]+, and [GGG•]+ were substantially different, providing experimental proof that initially these ions have distinct structures. DFT calculations showed that direct dissociations are competitive with interconversions followed by dissociation.

  16. Passive millimeter wave differential interference contrast polarimetry

    DOE Patents [OSTI]

    Bernacki, Bruce E; Kelly, James F; Sheen, David M; Tedeschi, Jonathan R; Hall, Thomas E; Hatchell, Brian K; Valdez, Patrick; McMakin, Douglas L

    2014-04-29

    Differential polarization imaging systems include an axicon configured to provide a displacement of ray bundles associated with different image patches. The displaced ray bundles are directed to antenna horns and orthomode transducers so as to provide outputs correspond to orthogonal linear states of polarization (SOPs). The outputs are directed to a differential radiometer so that Stokes parameter differences between image patches can be obtained. The ray bundle displacements can be selected to correspond to a mechanical spacing of antenna horns. In some examples, ray bundle displacement corresponds to a displacement less than the diffraction limit.

  17. A taxonomy of automatic differentiation tools

    SciTech Connect (OSTI)

    Juedes, D.W. . Dept. of Computer Science)

    1991-01-01

    Many of the current automatic differentiation (AD) tools have similar characteristics. Unfortunately, the similarities between these various AD tools often cannot be easily ascertained by reading the corresponding documentation. To clarify this situation, a taxonomy of AD tools is presented. The taxonomy places AD tools into the Elemental, Extensional, Integral, Operational, and Symbolic classes. This taxonomy is used to classify twenty-nine AD tools. Each tool is examined individually with respect to the mode of differentiation used and the degree of derivatives computed. A list detailing the availability of the surveyed AD tools is provided in the Appendix. 54 refs., 3 figs., 1 tab.

  18. ARM - Campaign Instrument - htdma

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    govInstrumentshtdma Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Campaign Instrument : Humidified Tandem Differential Mobility Analyzer (HTDMA) Instrument Categories Aerosols Campaigns Marine ARM GPCI Investigation of Clouds (MAGIC) [ Download Data ] MAGIC (Marine ARM GPCI Investigation of Clouds); Mobile Facility, 2012.10.01 - 2013.09.30 Primary Measurements Taken The following measurements are those considered scientifically relevant. Refer

  19. Method of multiplexed analysis using ion mobility spectrometer

    DOE Patents [OSTI]

    Belov, Mikhail E. (Richland, WA); Smith, Richard D. (Richland, WA)

    2009-06-02

    A method for analyzing analytes from a sample introduced into a Spectrometer by generating a pseudo random sequence of a modulation bins, organizing each modulation bin as a series of submodulation bins, thereby forming an extended pseudo random sequence of submodulation bins, releasing the analytes in a series of analyte packets into a Spectrometer, thereby generating an unknown original ion signal vector, detecting the analytes at a detector, and characterizing the sample using the plurality of analyte signal subvectors. The method is advantageously applied to an Ion Mobility Spectrometer, and an Ion Mobility Spectrometer interfaced with a Time of Flight Mass Spectrometer.

  20. New Feedstocks and Replacement Fuels - Future Energy for Mobility |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Fuels - Future Energy for Mobility New Feedstocks and Replacement Fuels - Future Energy for Mobility Presentation given at DEER 2006, August 20-24, 2006, Detroit, Michigan. Sponsored by the U.S. DOE's EERE FreedomCar and Fuel Partnership and 21st Century Truck Programs. 2006_deer_simnick.pdf (542.48 KB) More Documents & Publications Fuel-Cycle Energy and Emissions Analysis with the GREET Model Cross-cutting Technologies for Advanced Biofuels Well-to-Wheels Analysis

  1. Mobile Source Air Toxics Rule (released in AEO2008)

    Reports and Publications (EIA)

    2008-01-01

    On February 9, 2007, the Environmental Protection Agency (EPA) released its MSAT2 rule, which will establish controls on gasoline, passenger vehicles, and portable fuel containers. The controls are designed to reduce emissions of benzene and other hazardous air pollutants. Benzene is a known carcinogen, and the EPA estimates that mobile sources produced more than 70% of all benzene emissions in 1999. Other mobile source air toxics, including 1,3-butadiene, formaldehyde, acetaldehyde, acrolein, and naphthalene, also are thought to increase cancer rates or contribute to other serious health problems.

  2. Continuum Modeling and Control of Large Nonuniform Wireless Networks via Nonlinear Partial Differential Equations

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Zhang, Yang; Chong, Edwin K. P.; Hannig, Jan; Estep, Donald

    2013-01-01

    We inmore » troduce a continuum modeling method to approximate a class of large wireless networks by nonlinear partial differential equations (PDEs). This method is based on the convergence of a sequence of underlying Markov chains of the network indexed by N , the number of nodes in the network. As N goes to infinity, the sequence converges to a continuum limit, which is the solution of a certain nonlinear PDE. We first describe PDE models for networks with uniformly located nodes and then generalize to networks with nonuniformly located, and possibly mobile, nodes. Based on the PDE models, we develop a method to control the transmissions in nonuniform networks so that the continuum limit is invariant under perturbations in node locations. This enables the networks to maintain stable global characteristics in the presence of varying node locations.« less

  3. Method for mobilization of hazardous metal ions in soils

    DOE Patents [OSTI]

    Dugan, Patrick R.; Pfister, Robert M.

    1995-01-01

    A microbial process for removing heavy metals such as bismuth, cadmium, lead, thorium, uranium and other transuranics from soils and sediments, utilizing indigenous, or isolates of indigenous, microorganisms and reducing agents, such as cysteine or sodium thioglycollate, or complexing agents such as the amino acid glycine, to effect the mobilization or release of the metals from the soil particles.

  4. Electron mobility enhancement in (100) oxygen-inserted silicon channel

    SciTech Connect (OSTI)

    Xu, Nuo; King Liu, Tsu-Jae; Takeuchi, Hideki; Hytha, Marek; Cody, Nyles W.; Stephenson, Robert J.; Mears, Robert J.; Kwak, Byungil; Cha, Seon Yong

    2015-09-21

    High performance improvement (+88% in peak G{sub m} and >30% in linear and saturation region drain currents) was observed for N-MOSFETs with Oxygen-Inserted (OI) Si channel. From TCAD analysis of the C-V measurement data, the improvement was confirmed to be due to electron mobility enhancement of the OI Si channel (+75% at N{sub inv} = 4.0 × 10{sup 12} cm{sup −2} and +25% at N{sub inv} = 8.0 × 10{sup 12} cm{sup −2}). Raman and high-resolution Rutherford backscattering measurements confirmed that negligible strain is induced in the OI Si layer, and hence, it cannot be used to explain the origin of mobility improvement. Poisson-Schrödinger based quantum mechanical simulation was performed, taking into account phonon, surface roughness and Coulomb scatterings. The OI layer was modeled as a “quasi barrier” region with reference to the Si conduction band edge to confine inversion electrons. Simulation explains the measured electron mobility enhancement as the confinement effect of inversion electrons while the formation of an super-steep retrograde well doping profile in the channel (as a result of dopant diffusion blocking effect accompanied by introduction of the OI layer) also contributes 50%–60% of the mobility improvement.

  5. Rail-to-rail differential input amplification stage with main and surrogate differential pairs

    DOE Patents [OSTI]

    Britton, Jr., Charles Lanier; Smith, Stephen Fulton

    2007-03-06

    An operational amplifier input stage provides a symmetrical rail-to-rail input common-mode voltage without turning off either pair of complementary differential input transistors. Secondary, or surrogate, transistor pairs assume the function of the complementary differential transistors. The circuit also maintains essentially constant transconductance, constant slew rate, and constant signal-path supply current as it provides rail-to-rail operation.

  6. Ion mobility spectrometry–mass spectrometry (IMS–MS) for on- and offline analysis of atmospheric gas and aerosol species

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Krechmer, Jordan E.; Groessl, Michael; Zhang, Xuan; Junninen, Heikki; Massoli, Paola; Lambe, Andrew T.; Kimmel, Joel R.; Cubison, Michael J.; Graf, Stephan; Lin, Ying-Hsuan; et al

    2016-07-25

    Measurement techniques that provide molecular-level information are needed to elucidate the multiphase processes that produce secondary organic aerosol (SOA) species in the atmosphere. Here we demonstrate the application of ion mobility spectrometry-mass spectrometry (IMS–MS) to the simultaneous characterization of the elemental composition and molecular structures of organic species in the gas and particulate phases. Molecular ions of gas-phase organic species are measured online with IMS–MS after ionization with a custom-built nitrate chemical ionization (CI) source. This CI–IMS–MS technique is used to obtain time-resolved measurements (5 min) of highly oxidized organic molecules during the 2013 Southern Oxidant and Aerosol Study (SOAS) ambientmore » field campaign in the forested SE US. The ambient IMS–MS signals are consistent with laboratory IMS–MS spectra obtained from single-component carboxylic acids and multicomponent mixtures of isoprene and monoterpene oxidation products. Mass-mobility correlations in the 2-D IMS–MS space provide a means of identifying ions with similar molecular structures within complex mass spectra and are used to separate and identify monoterpene oxidation products in the ambient data that are produced from different chemical pathways. Water-soluble organic carbon (WSOC) constituents of fine aerosol particles that are not resolvable with standard analytical separation methods, such as liquid chromatography (LC), are shown to be separable with IMS–MS coupled to an electrospray ionization (ESI) source. The capability to use ion mobility to differentiate between isomers is demonstrated for organosulfates derived from the reactive uptake of isomers of isoprene epoxydiols (IEPOX) onto wet acidic sulfate aerosol. Controlled fragmentation of precursor ions by collisionally induced dissociation (CID) in the transfer region between the IMS and the MS is used to validate MS peak assignments, elucidate structures of

  7. V-134: Cisco AnyConnect Secure Mobility Client Heap Overflow...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    4: Cisco AnyConnect Secure Mobility Client Heap Overflow Lets Local Users Gain Elevated Privileges V-134: Cisco AnyConnect Secure Mobility Client Heap Overflow Lets Local Users ...

  8. OSTIblog Articles in the mobile Topic | OSTI, US Dept of Energy...

    Office of Scientific and Technical Information (OSTI)

    Science.gov Mobile: Top Ten in Federal Apps by Linda McBrearty 03 Jul, 2012 in Products and Content 4733 Scigovhome640X960.jpg Science.gov Mobile: Top Ten in Federal Apps Read ...

  9. Measuring "Real World" Heavy-Duty Diesel Emissions with a Mobile...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    "Real World" Heavy-Duty Diesel Emissions with a Mobile Lab Measuring "Real World" Heavy-Duty Diesel Emissions with a Mobile Lab 2002 DEER Conference Presentation: University of ...

  10. Comment on "Kinetic theory for a mobile impurity in a degenerate...

    Office of Scientific and Technical Information (OSTI)

    Comment on "Kinetic theory for a mobile impurity in a degenerate Tonks-Girardeau gas" Citation Details In-Document Search Title: Comment on "Kinetic theory for a mobile impurity in ...

  11. Comment on "Kinetic theory for a mobile impurity in a degenerate...

    Office of Scientific and Technical Information (OSTI)

    Comment on "Kinetic theory for a mobile impurity in a degenerate Tonks-Girardeau gas" Title: Comment on "Kinetic theory for a mobile impurity in a degenerate Tonks-Girardeau gas" ...

  12. Exxon Mobil QuestAir Plug Power Ben Gurion University Hydrogen...

    Open Energy Info (EERE)

    Exxon Mobil QuestAir Plug Power Ben Gurion University Hydrogen JV Jump to: navigation, search Name: Exxon Mobil, QuestAir, Plug Power , & Ben Gurion University Hydrogen JV Place:...

  13. Control Scheme Modifications Increase Efficiency of Steam Generation System at Exxon Mobil Gas Plant

    SciTech Connect (OSTI)

    2002-01-01

    This case study highlights control scheme modifications made to the steam system at ExxonMobil's Mary Ann Gas Plant in Mobile, Alabama, which improved steam flow efficiency and reduced energy costs.

  14. H:\\DOD\\OUTREACH\\PUBS\\DRAFTS\\Mobile 6 users guide\\420r03010.wpd

    National Nuclear Security Administration (NNSA)

    ... Many areas of the country have implemented inspection and maintenance (IM) programs to further reduce mobile source air pollution. (Note: MOBILE6 does not model the impact of IM ...

  15. MODELING OF LONG-TERM FATE OF MOBILIZED FINES DUE TO DAM-EMBANKMENT...

    Office of Scientific and Technical Information (OSTI)

    MODELING OF LONG-TERM FATE OF MOBILIZED FINES DUE TO DAM-EMBANKMENT INTERFACIAL DISLOCATIONS Citation Details In-Document Search Title: MODELING OF LONG-TERM FATE OF MOBILIZED ...

  16. High Bandwidth Differential Amplifier for Shock Experiments

    SciTech Connect (OSTI)

    Ross, P. W., Tran, V., Chau, R.

    2012-04-30

    We developed a high bandwidth differential amplifier for gas gun shock experiments/applications. The circuit has a bandwidth > 1 GHz, and is capable of measuring signals of ?1.5 V with a common mode rejection of 250 V. Conductivity measurements of gas gun targets are measured by flowing high currents through the targets. The voltage is measured across the target using a technique similar to a four-point probe. Because of the design of the current source and load, the target voltage is approximately 250 V relative to ground. Since the expected voltage change in the target is < 1 V, the differential amplifier must have a large common mode rejection. High pass filters suppress internal ringing of operational amplifiers. Results of bench tests are shown.

  17. Autyomatic Differentiation of C/C++

    Energy Science and Technology Software Center (OSTI)

    2005-11-14

    Automatic differentiation (AD) tools mechanize the process of developing code for the computation of derivatives. AD avoids the inaccuracies inherent in numerical approximations. Furthermore, sophisticated AD algoirthms can often produce c ode that is more reliable and more efficient than code written by an expert programmer. ADIC is the first and only AD tool for C and C++ based on compiler technology. This compiler foundation makes possible analyses and optimizations not available in toos basedmoreon operator overloading. The earliest implementations of ADIC included support for ANSI C applications, ADIC 2.0 lverages EDG, a commercial C/C++ parser, to provide robust C++ differentiation support. Modern AD tools, including ADIC are implemented in a modular way, aiming to isolate language-dependent program analyses and semantic transformations. The component design leads to much higher implementation quality because the different components can be implemented by experts in each of the different domains involved. For example, a compiler expert can focus on parsing, canonicalizing, and unparising C and C++, while an expert in graph theory and algorithms can produce new differentiation modules without having to worry about the complexity of parsing and generating C++ code. Thsi separation of concerns was achieved through the use of language-independent program analysis interfaces (in collaboration with researcgers at Rice University) and a language-independent XML representation of the computational portions of programs (XAIF). In addition to improved robustness and faster development times, this design naturally enables the reuse of program analysis algorithms and differentiation modules in compiler-based AD tools for other languages. In fact, the analysis and differention components are used in both ADIC and the Open AD Fortran front-end (based on Rice's Open64 compiler.less

  18. Autyomatic Differentiation of C/C++

    Energy Science and Technology Software Center (OSTI)

    2005-11-14

    Automatic differentiation (AD) tools mechanize the process of developing code for the computation of derivatives. AD avoids the inaccuracies inherent in numerical approximations. Furthermore, sophisticated AD algoirthms can often produce c ode that is more reliable and more efficient than code written by an expert programmer. ADIC is the first and only AD tool for C and C++ based on compiler technology. This compiler foundation makes possible analyses and optimizations not available in toos basedmore » on operator overloading. The earliest implementations of ADIC included support for ANSI C applications, ADIC 2.0 lverages EDG, a commercial C/C++ parser, to provide robust C++ differentiation support. Modern AD tools, including ADIC are implemented in a modular way, aiming to isolate language-dependent program analyses and semantic transformations. The component design leads to much higher implementation quality because the different components can be implemented by experts in each of the different domains involved. For example, a compiler expert can focus on parsing, canonicalizing, and unparising C and C++, while an expert in graph theory and algorithms can produce new differentiation modules without having to worry about the complexity of parsing and generating C++ code. Thsi separation of concerns was achieved through the use of language-independent program analysis interfaces (in collaboration with researcgers at Rice University) and a language-independent XML representation of the computational portions of programs (XAIF). In addition to improved robustness and faster development times, this design naturally enables the reuse of program analysis algorithms and differentiation modules in compiler-based AD tools for other languages. In fact, the analysis and differention components are used in both ADIC and the Open AD Fortran front-end (based on Rice's Open64 compiler.« less

  19. The Fuel Cell Mobile Light Project- A DOE Market Transformation Activity

    Office of Energy Efficiency and Renewable Energy (EERE)

    Presentation slides from the Fuel Cell Technologies Program webinar, Fuel Cell Mobile Lighting, held on November 13, 2012.

  20. V-134: Cisco AnyConnect Secure Mobility Client Heap Overflow Lets Local

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Users Gain Elevated Privileges | Department of Energy 4: Cisco AnyConnect Secure Mobility Client Heap Overflow Lets Local Users Gain Elevated Privileges V-134: Cisco AnyConnect Secure Mobility Client Heap Overflow Lets Local Users Gain Elevated Privileges April 15, 2013 - 1:30am Addthis PROBLEM: Cisco AnyConnect Secure Mobility Client Heap Overflow Lets Local Users Gain Elevated Privileges PLATFORM: Cisco AnyConnect Secure Mobility Client Cisco Secure Desktop ABSTRACT: Some vulnerabilities

  1. Unipolar time-differential charge sensing in non-dispersive amorphous solids

    SciTech Connect (OSTI)

    Goldan, A. H.; Rowlands, J. A.; Tousignant, O.; Karim, K. S.

    2013-06-14

    The use of high resistivity amorphous solids as photodetectors, especially amorphous selenium, is currently of great interest because they are readily produced over large area at substantially lower cost compared to grown crystalline solids. However, amorphous solids have been ruled out as viable radiation detection media for high frame-rate applications, such as single-photon-counting imaging, because of low carrier mobilities, transit-time-limited photoresponse, and consequently, poor time resolution. To circumvent the problem of poor charge transport in amorphous solids, we propose unipolar time-differential charge sensing by establishing a strong near-field effect using an electrostatic shield within the material. For the first time, we have fabricated a true Frisch grid inside a solid-state detector by evaporating amorphous selenium over photolithographically prepared multi-well substrates. The fabricated devices are characterized with optical, x-ray, and gamma-ray impulse-like excitations. Results prove the proposed unipolar time-differential property and show that time resolution in non-dispersive amorphous solids can be improved substantially to reach the theoretical limit set by spatial spreading of the collected Gaussian carrier cloud.

  2. Application of structural-mechanics methods to the design of large tandem-mirror fusion devices (MFTF-B). Revision 1

    SciTech Connect (OSTI)

    Karpenko, V.N.; Ng, D.S.

    1985-08-15

    The Mirror Fusion Test Facility (MFTF-B) at Lawrence Livermore National Laboratory requires state-of-the-art structural-mechanics methods to deal with access constraints for plasma heating and diagnostics, alignment requirements, and load complexity and variety. Large interactive structures required an integrated analytical approach to achieve a reasonable level of overall system optimization. The Tandem Magnet Generator (TMG) creates a magnet configuration for the EFFI calculation of electromagnetic-field forces that, coupled with other loads, form the input loading to magnet and vessel finite-element models. The analytical results provide the data base for detailed design of magnet, vessel, foundation, and interaction effects. 13 refs.

  3. Soft x-ray intensity profile measurements of electron cyclotron heated plasmas using semiconductor detector arrays in GAMMA 10 tandem mirror

    SciTech Connect (OSTI)

    Minami, R., E-mail: minami@prc.tsukuba.ac.jp; Imai, T.; Kariya, T.; Numakura, T.; Eguchi, T.; Kawarasaki, R.; Nakazawa, K.; Kato, T.; Sato, F.; Nanzai, H.; Uehara, M.; Endo, Y.; Ichimura, M. [Plasma Research Center, University of Tsukuba, Tsukuba, Ibaraki 305-8577 (Japan)

    2014-11-15

    Temporally and spatially resolved soft x-ray analyses of electron cyclotron heated plasmas are carried out by using semiconductor detector arrays in the GAMMA 10 tandem mirror. The detector array has 16-channel for the measurements of plasma x-ray profiles so as to make x-ray tomographic reconstructions. The characteristics of the detector array make it possible to obtain spatially resolved plasma electron temperatures down to a few tens eV and investigate various magnetohydrodynamic activities. High power electron cyclotron heating experiment for the central-cell region in GAMMA 10 has been started in order to reduce the electron drag by increasing the electron temperature.

  4. Tandem dissolution of UO 3 in amide-based acidic ionic liquid and in situ electrodeposition of UO 2 with regeneration of the ionic liquid: a closed cycle

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Wanigasekara, Eranda; Freiderich, John W.; Sun, Xiao-Guang; Meisner, Roberta A.; Luo, Huimin; Delmau, Lætitia H.; Dai, Sheng; Moyer, Bruce A.

    2016-05-19

    A closed cycle is demonstrated for the tandem dissolution and electroreduction of UO3 to UO2 with regeneration of the acidic ionic liquid. The dissolution is achieved by use of the acidic ionic liquid N,N-dimethylacetimidium bis(trifluoromethanesulfonimide) in 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonimide) serving as the diluent. Bulk electrolysis performed at 1.0 V vs. Ag reference yields a dark brown-black uranium deposit (UO2) on the cathode. Anodic oxidation of water in the presence of dimethylacetamide regenerates the acidic ionic liquid. We have demonstrated the individual steps in the cycle together with a sequential dissolution, electroreduction, and regeneration cycle.

  5. Ion dynamics and mixed mobile ion effect in fluoride glasses

    SciTech Connect (OSTI)

    Ghosh, S.; Ghosh, A.

    2005-06-15

    We report the ionic relaxation and mixed mobile ion effect in 50ZrF{sub 4}-10BaF{sub 2}-10YF{sub 3}-(30-x)LiF-xNaF fluoride glass series, where fluorine anions participate in the diffusion process in addition to alkali cations, unlike mixed alkali oxide glasses and crystals. By analyzing the ion dynamics in the framework of a power-law model as well as modulus formalism we have observed mixed mobile ion effect in the dc conductivity and its activation energy, the crossover frequency and its activation energy, the conductivity relaxation frequency and its activation energy, and also in the decoupling index. We have correlated these phenomena with the fractal dimension of the conduction pathways in the mixed alkali fluoride glasses compared to the single alkali glasses. We have shown that the relaxation dynamics in mixed alkali fluoride glasses is independent of temperature but dependent on glass composition.

  6. Ion mobility spectrometer using frequency-domain separation

    DOE Patents [OSTI]

    Martin, Stephen J.; Butler, Michael A.; Frye, Gregory C.; Schubert, W. Kent

    1998-01-01

    An apparatus and method is provided for separating and analyzing chemical species in an ion mobility spectrometer using a frequency-domain technique wherein the ions generated from the chemical species are selectively transported through an ion flow channel having a moving electrical potential therein. The moving electrical potential allows the ions to be selected according to ion mobility, with certain of the ions being transported to an ion detector and other of the ions being effectively discriminated against. The apparatus and method have applications for sensitive chemical detection and analysis for monitoring of exhaust gases, hazardous waste sites, industrial processes, aerospace systems, non-proliferation, and treaty verification. The apparatus can be formed as a microelectromechanical device (i.e. a micromachine).

  7. High mobility ZnO nanowires for terahertz detection applications

    SciTech Connect (OSTI)

    Liu, Huiqiang; Peng, Rufang E-mail: chusheng@mail.sysu.edu.cn; Chu, Shijin; Chu, Sheng E-mail: chusheng@mail.sysu.edu.cn

    2014-07-28

    An oxide nanowire material was utilized for terahertz detection purpose. High quality ZnO nanowires were synthesized and field-effect transistors were fabricated. Electrical transport measurements demonstrated the nanowire with good transfer characteristics and fairly high electron mobility. It is shown that ZnO nanowires can be used as building blocks for the realization of terahertz detectors based on a one-dimensional plasmon detection configuration. Clear terahertz wave (∼0.3 THz) induced photovoltages were obtained at room temperature with varying incidence intensities. Further analysis showed that the terahertz photoresponse is closely related to the high electron mobility of the ZnO nanowire sample, which suggests that oxide nanoelectronics may find useful terahertz applications.

  8. Mobile monolithic polymer elements for flow control in microfluidic devices

    DOE Patents [OSTI]

    Hasselbrink, Jr., Ernest F.; Rehm, Jason E.; Shepodd, Timothy J.; Kirby, Brian J.

    2005-11-11

    A cast-in-place and lithographically shaped mobile, monolithic polymer element for fluid flow control in microfluidic devices and method of manufacture. Microfluid flow control devices, or microvalves that provide for control of fluid or ionic current flow can be made incorporating a cast-in-place, mobile monolithic polymer element, disposed within a microchannel, and driven by fluid pressure (either liquid or gas) against a retaining or sealing surface. The polymer elements are made by the application of lithographic methods to monomer mixtures formulated in such a way that the polymer will not bond to microchannel walls. The polymer elements can seal against pressures greater than 5000 psi, and have a response time on the order of milliseconds. By the use of energetic radiation it is possible to depolymerize selected regions of the polymer element to form shapes that cannot be produced by conventional lithographic patterning and would be impossible to machine.

  9. Mobile monolithic polymer elements for flow control in microfluidic devices

    DOE Patents [OSTI]

    Hasselbrink, Jr., Ernest F.; Rehm, Jason E.; Shepodd, Timothy J.

    2004-08-31

    A cast-in-place and lithographically shaped mobile, monolithic polymer element for fluid flow control in microfluidic devices and method of manufacture. Microfluid flow control devices, or microvalves that provide for control of fluid or ionic current flow can be made incorporating a cast-in-place, mobile monolithic polymer element, disposed within a microchannel, and driven by either fluid or gas pressure against a retaining or sealing surface. The polymer elements are made by the application of lithographic methods to monomer mixtures formulated in such a way that the polymer will not bond to microchannel walls. The polymer elements can seal against pressures greater than 5000 psi, and have a response time on the order of milliseconds. By the use of energetic radiation it is possible to depolymerize selected regions of the polymer element to form shapes that cannot be produced by conventional lithographic patterning and would be impossible to machine.

  10. Mobile Monolith Polymer Elements For Flow Control In Microfluidic Systems

    DOE Patents [OSTI]

    Hasselbrink, Jr., Ernest F.; Rehm, Jason E.; Shepodd, Timothy J.; Kirby, Brian J.

    2006-01-24

    A cast-in-place and lithographically shaped mobile, monolithic polymer element for fluid flow control in microfluidic devices and method of manufacture. Microfluid flow control devices, or microvalves that provide for control of fluid or ionic current flow can be made incorporating a cast-in-place, mobile monolithic polymer element, disposed within a microchannel, and driven by fluid pressure (either liquid or gas) against a retaining or sealing surface. The polymer elements are made by the application of lithographic methods to monomer mixtures formulated in such a way that the polymer will not bond to microchannel walls. The polymer elements can seal against pressures greater than 5000 psi, and have a response time on the order of milliseconds. By the use of energetic radiation it is possible to depolymerize selected regions of the polymer element to form shapes that cannot be produced by conventional lithographic patterning and would be impossible to machine.

  11. Investigation of coal tar mobility at a former MGP site

    SciTech Connect (OSTI)

    Moo-Young, H.K.; Mo, X.H.; Waterman, R.; Coleman, A.; Saroff, S.

    2009-11-15

    The presence of coal tar in the subsurface of former manufactured gas plant sites poses an environmental hazard and a potential threat to public health. Coal tar can release various chemical compounds that are transported into the groundwater. Before any efforts can be made to remove coal tar from contaminated subsurface soils, it is recommended to characterize coal tar properties and composition and to delineate the residual saturation point between mobile and immobile coal tar. This paper presents a new innovative field device, the Res-SAT field tool, and laboratory procedures that can be used to determine the saturation-capillary pressure relationship for a soil-water coal-tar system and the critical pressure for coal tar mobility.

  12. An iterative learning controller for nonholonomic mobile robots

    SciTech Connect (OSTI)

    Oriolo, G.; Panzieri, S.; Ulivi, G.

    1998-09-01

    The authors present an iterative learning controller that applies to nonholonomic mobile robots, as well as other systems that can be put in chained form. The learning algorithm exploits the fact that chained-form. The learning algorithm exploits the fact that chained-form systems are linear under piecewise-constant inputs. The proposed control scheme requires the execution of a small number of experiments to drive the system to the desired state in finite time, with nice convergence and robustness properties with respect to modeling inaccuracies as well as disturbances. To avoid the necessity of exactly reinitializing the system at each iteration, the basic method is modified so as to obtain a cyclic controller, by which the system is cyclically steered through an arbitrary sequence of states. As a case study, a carlike mobile robot is considered. Both simulation and experimental results are reported to show the performance of the method.

  13. Mobile Data Collection Applications: A Proof of Concept

    SciTech Connect (OSTI)

    Chang, J

    2006-09-20

    This project's goal is to provide a proof of concept for mobile data collection applications, and identify the best ways such applications could be implemented and used. Such an application should decrease the time and resources users now need to devote to redundant data processes, and provide an easy of locating and retrieving data at a later time. The two types of available mobile devices, Personal Digital Assistants and Tablet Personal Computers, each have their particular strengths that suggest themselves for certain types of applications. As such, parallel data collection applications have been developed, with a common web application for uploading information to the database. While these aspects have been developed and proven, it still remains to refine these applications, develop the tables to hold their data, and field-test with users for their feedback.

  14. Ion mobility spectrometer using frequency-domain separation

    DOE Patents [OSTI]

    Martin, S.J.; Butler, M.A.; Frye, G.C.; Schubert, W.K.

    1998-08-04

    An apparatus and method are provided for separating and analyzing chemical species in an ion mobility spectrometer using a frequency-domain technique wherein the ions generated from the chemical species are selectively transported through an ion flow channel having a moving electrical potential therein. The moving electrical potential allows the ions to be selected according to ion mobility, with certain of the ions being transported to an ion detector and other of the ions being effectively discriminated against. The apparatus and method have applications for sensitive chemical detection and analysis for monitoring of exhaust gases, hazardous waste sites, industrial processes, aerospace systems, non-proliferation, and treaty verification. The apparatus can be formed as a microelectromechanical device (i.e. a micromachine). 6 figs.

  15. Theoretical interpretation of the electron mobility behavior in InAs nanowires

    SciTech Connect (OSTI)

    Marin, E. G. Ruiz, F. G. Godoy, A.; Tienda-Luna, I. M.; Martnez-Blanque, C.; Gmiz, F.

    2014-11-07

    This work studies the electron mobility in InAs nanowires (NWs), by solving the Boltzmann Transport Equation under the Momentum Relaxation Time approximation. The numerical solver takes into account the contribution of the main scattering mechanisms present in III-V compound semiconductors. It is validated against experimental field effect-mobility results, showing a very good agreement. The mobility dependence on the nanowire diameter and carrier density is analyzed. It is found that surface roughness and polar optical phonons are the scattering mechanisms that mainly limit the mobility behavior. Finally, we explain the origin of the oscillations observed in the mobility of small NWs at high electric fields.

  16. NREL Developed Mobile App for Alternative Fueling Station Locations

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Released - News Releases | NREL NREL Developed Mobile App for Alternative Fueling Station Locations Released New application for iPhone helps users find stations offering electricity, biodiesel, natural gas, and other alternative fuels. November 7, 2013 iPhone users now have access to a free application that locates fueling stations offering alternative fuels, including electricity, natural gas, biodiesel, e85 Ethanol, propane and hydrogen. The Energy Department's (DOE) National Renewable

  17. NREL Launches Sustainable Mobility Initiative, Joins CDOT Partnership -

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    News Feature | NREL Launches Sustainable Mobility Initiative, Joins CDOT Partnership January 22, 2016 NREL researchers look at colored map of the United States in 3D visualization room. Today, transportation operation and energy systems data are generated at an unprecedented scale. NREL's data experts and engineers analyze large sets of complex data-or "big data"-to develop solutions that support the research, development, and deployment of market-ready technologies that reduce

  18. Geochemical Triggers of Arsenic Mobilization during Managed Aquifer

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Recharge | Stanford Synchrotron Radiation Lightsource Geochemical Triggers of Arsenic Mobilization during Managed Aquifer Recharge Monday, February 29, 2016 Managed aquifer recharge (MAR) is an increasingly used water enhancement strategy, which involves subsurface storage of water supplies in groundwater aquifers. While MAR projects have the potential to alleviate water deficits, they can also adversely impact groundwater quality by altering the native geochemistry of the aquifer and

  19. ARM Operations and Engineering Procedure Mobile Facility Site Startup

    SciTech Connect (OSTI)

    Voyles, Jimmy W

    2015-05-01

    This procedure exists to define the key milestones, necessary steps, and process rules required to commission and operate an Atmospheric Radiation Measurement (ARM) Mobile Facility (AMF), with a specific focus toward on-time product delivery to the ARM Data Archive. The overall objective is to have the physical infrastructure, networking and communications, and instrument calibration, grooming, and alignment (CG&A) completed with data products available from the ARM Data Archive by the Operational Start Date milestone.

  20. Method for measuring the drift mobility in doped semiconductors

    DOE Patents [OSTI]

    Crandall, Richard S.

    1982-01-01

    A method for measuring the drift mobility of majority carriers in semiconductors consists of measuring the current transient in a Schottky-barrier device following the termination of a forward bias pulse. An example is given using an amorphous silicon hydrogenated material doped with 0.2% phosphorous. The method is particularly useful with material in which the dielectric relaxation time is shorter than the carrier transit time. It is particularly useful in material useful in solar cells.

  1. Method for measuring the drift mobility in doped semiconductors

    DOE Patents [OSTI]

    Crandall, R.S.

    1982-03-09

    A method for measuring the drift mobility of majority carriers in semiconductors consists of measuring the current transient in a Schottky-barrier device following the termination of a forward bias pulse. An example is given using an amorphous silicon hydrogenated material doped with 0.2% phosphorus. The method is particularly useful with material in which the dielectric relaxation time is shorter than the carrier transit time. It is particularly useful in material useful in solar cells. 10 figs.

  2. Method for mobilization of hazardous metal ions in soils

    DOE Patents [OSTI]

    Dugan, P.R.; Pfister, R.M.

    1995-06-27

    A microbial process is revealed for removing heavy metals such as bismuth, cadmium, lead, thorium, uranium and other transuranics from soils and sediments. The method utilizes indigenous, or isolates of indigenous, microorganisms and reducing agents, such as cysteine or sodium thioglycollate, or complexing agents such as the amino acid glycine, to effect the mobilization or release of the metals from the soil particles. 5 figs.

  3. Mobile worksystems for decontamination and decommissioning operations. Final report

    SciTech Connect (OSTI)

    1997-02-01

    This project is an interdisciplinary effort to develop effective mobile worksystems for decontamination and decommissioning (D&D) of facilities within the DOE Nuclear Weapons Complex. These mobile worksystems will be configured to operate within the environmental and logistical constraints of such facilities and to perform a number of work tasks. Our program is designed to produce a mobile worksystem with capabilities and features that are matched to the particular needs of D&D work by evolving the design through a series of technological developments, performance tests and evaluations. The Phase I effort was based on a robot called the Remote Work Vehicle (RWV) that was previously developed by CMU for use in D&D operations at the Three Mile Island Unit 2 Reactor Building basement. During Phase I of this program, the RWV was rehabilitated and upgraded with contemporary control and user interface technologies and used as a testbed for remote D&D operations. We established a close working relationship with the DOE Robotics Technology Development Program (RTDP). In the second phase, we designed and developed a next generation mobile worksystem, called Rosie, and a semi-automatic task space scene analysis system, called Artisan, using guidance from RTDP. Both systems are designed to work with and complement other RTDP D&D technologies to execute selective equipment removal scenarios in which some part of an apparatus is extricated while minimally disturbing the surrounding objects. RTDP has identified selective equipment removal as a timely D&D mission, one that is particularly relevant during the de-activation and de-inventory stages of facility transitioning as a means to reduce the costs and risks associated with subsequent surveillance and monitoring. In the third phase, we tested and demonstrated core capabilities of Rosie and Artisan; we also implemented modifications and enhancements that improve their relevance to DOE`s facility transitioning mission.

  4. Nightmares with Mobile Devices Are Just Around the Corner!

    SciTech Connect (OSTI)

    Kurt Derr

    2007-03-01

    Mobile Devices (MDs) such as Personal Digital Assistants (PDAs), smart phones, handheld personal computers, and Tablet PCs, are proliferating in the marketplace. Cheap and ubiquitous mobile computing devices represent computing’s fifth wave [1], bringing about new opportunities in the marketplace. As MDs become more powerful and commonplace with ubiquitous connectivity, the line that currently divides these handheld devices from typical network computers will become very unclear. Mobile devices have become integrated into the business processes of both government and commercial institutions. MDs are small, portable, and able to store large amounts of information. The breadth of communication options (infrared, wireless, docking station) for MDs introduces many security risks. Some of the problems associated with MDs are: easy to loose, misplace, or have stolen, potential loss/comprise of company data (user ids, passwords, contacts, sensitive documentation, credit card numbers), increases the opportunity for a backdoor into an enterprise’s network, lack of authentication and limited logging capability. The use of these devices poses a risk to the security of an organization.

  5. Composting in tandem

    SciTech Connect (OSTI)

    Sheehan, K.

    1994-03-01

    A composting company, a county, and a waste company have formed a symbiotic public/private relationship that is helping to extend the life of the area's landfills, as well as produce a needed product. California state assembly bill 939, passed in 1989, directed local governments to reduce the amount of garbage being landfilled in order to curtail the need for new landfills. Cities and counties in California are now mandated to reduce the volume of their waste stream by 25% by 1995. By the year 2000, the waste stream must be reduced by 50%. And the law has teeth -- to ensure these percentages are met, a $10,000 fine can be imposed for each day a deadline is missed. According to 1990 figures, Sonoma County's well-established recycling programs have been successful at diverting 15% of the county's waste stream from the landfill. Paula Magyari, a waste management specialist with the county Public Works Department, says yard wastes account for 13% of the waste stream in Sonoma County; wood wastes for at least 15%. At 13% and 15%, they are two of the largest components of the waste stream, and, equally important, they represent the portion of the waste stream that is most readily reusable to meet the 25% goal.

  6. Differential white cell count by centrifugal microfluidics.

    SciTech Connect (OSTI)

    Sommer, Gregory Jon; Tentori, Augusto M.; Schaff, Ulrich Y.

    2010-07-01

    We present a method for counting white blood cells that is uniquely compatible with centrifugation based microfluidics. Blood is deposited on top of one or more layers of density media within a microfluidic disk. Spinning the disk causes the cell populations within whole blood to settle through the media, reaching an equilibrium based on the density of each cell type. Separation and fluorescence measurement of cell types stained with a DNA dye is demonstrated using this technique. The integrated signal from bands of fluorescent microspheres is shown to be proportional to their initial concentration in suspension. Among the current generation of medical diagnostics are devices based on the principle of centrifuging a CD sized disk functionalized with microfluidics. These portable 'lab on a disk' devices are capable of conducting multiple assays directly from a blood sample, embodied by platforms developed by Gyros, Samsung, and Abaxis. [1,2] However, no centrifugal platform to date includes a differential white blood cell count, which is an important metric complimentary to diagnostic assays. Measuring the differential white blood cell count (the relative fraction of granulocytes, lymphocytes, and monocytes) is a standard medical diagnostic technique useful for identifying sepsis, leukemia, AIDS, radiation exposure, and a host of other conditions that affect the immune system. Several methods exist for measuring the relative white blood cell count including flow cytometry, electrical impedance, and visual identification from a stained drop of blood under a microscope. However, none of these methods is easily incorporated into a centrifugal microfluidic diagnostic platform.

  7. AUTOMATIC DIFFERENTIATION OF AN EULERIAN HYDROCODE

    SciTech Connect (OSTI)

    R. HENNINGER; A. CARLE; P. MAUDLIN

    2000-11-01

    Automatic differentiation (AD) is applied to a two-dimensional Eulerian hydrodynamics computer code (hydrocode) to provide gradients that will be used for design optimization and uncertainty analysis. We examine AD in both the forward and adjoint (reverse) mode using Automatic Differentiation of Fortran (ADIFOR, version 3.0). Setup time, accuracy, and run times are described for three problems. The test set consists of a one-dimensional shock-propagation problem, a two-dimensional metal-jet-formation problem and a two-dimensional shell-collapse problem. Setup time for ADIFOR was approximately one month starting from a simplified, fixed-dimension version of the original code. ADIFOR produced accurate (as compared to finite difference) gradients in both modes for all of the problems. These test problems had 17 independent variables. We find that the forward mode is up to 39% slower and the adjoint mode is at least 11% faster than finding the gradient by means of finite differences. Problems of real interest will certainly have more independent variables. The adjoint mode is thus favored since the computational time increases only slightly for additional independent variables.

  8. Estimation of retired mobile phones generation in China: A comparative study on methodology

    SciTech Connect (OSTI)

    Li, Bo; Yang, Jianxin; Lu, Bin; Song, Xiaolong

    2015-01-15

    Highlights: • The sales data of mobile phones in China was revised by considering the amount of smuggled and counterfeit mobile phones. • The estimation of retired mobile phones in China was made by comparing some relevant methods. • The advanced result of estimation can help improve the policy-making. • The method suggested in this paper can be also used in other countries. • Some discussions on methodology are also conducted in order for the improvement. - Abstract: Due to the rapid development of economy and technology, China has the biggest production and possession of mobile phones around the world. In general, mobile phones have relatively short life time because the majority of users replace their mobile phones frequently. Retired mobile phones represent the most valuable electrical and electronic equipment (EEE) in the main waste stream because of such characteristics as large quantity, high reuse/recovery value and fast replacement frequency. Consequently, the huge amount of retired mobile phones in China calls for a sustainable management system. The generation estimation can provide fundamental information to construct the sustainable management system of retired mobile phones and other waste electrical and electronic equipment (WEEE). However, the reliable estimation result is difficult to get and verify. The priority aim of this paper is to provide proper estimation approach for the generation of retired mobile phones in China, by comparing some relevant methods. The results show that the sales and new method is in the highest priority in estimation of the retired mobile phones. The result of sales and new method shows that there are 47.92 million mobile phones retired in 2002, and it reached to 739.98 million in China in 2012. It presents an increasing tendency with some fluctuations clearly. Furthermore, some discussions on methodology, such as the selection of improper approach and error in the input data, are also conducted in order to

  9. Partial Differential Algebraic Sensitivity Analysis Code

    Energy Science and Technology Software Center (OSTI)

    1995-05-15

    PDASAC solves stiff, nonlinear initial-boundary-value in a timelike dimension t and a space dimension x. Plane, circular cylindrical or spherical boundaries can be handled. Mixed-order systems of partial differential and algebraic equations can be analyzed with members of order or 0 or 1 in t, 0,1 or 2 in x. Parametric sensitivities of the calculated states are compted simultaneously on request, via the Jacobian of the state equations. Initial and boundary conditions are efficiently reconciled.more » Local error control (in the max-norm or the 2-norm) is provided for the state vector and can include the parametric sensitivites if desired.« less

  10. Stirling cycle simulation without differential coefficients

    SciTech Connect (OSTI)

    Organ, A.J.

    1995-12-31

    With a simple transformation, the gas processes in the Stirling machine are described for all time and location in an algebraic equation free of differential coefficients of the unknowns. Local instantaneous heat transfer and friction are represented in function of local instantaneous Reynolds number, N{sub re}. The method avoids problems of numerical discretization, stability, convergence, artificial dispersion and diffusion. The paper presents the algebra of the transformation. Specimen solutions cover the temperature field of the gas circuit (exchangers and regenerator) over a representative cycle. When programmed for workstation the core code occupies some 2 dozen lines, and processing calls for seconds of CPU time. Availability of the solution means that intimate details of the gas processes are susceptible to examination using the most basic of computing facilities.

  11. Sensor for detecting and differentiating chemical analytes

    DOE Patents [OSTI]

    Yi, Dechang; Senesac, Lawrence R.; Thundat, Thomas G.

    2011-07-05

    A sensor for detecting and differentiating chemical analytes includes a microscale body having a first end and a second end and a surface between the ends for adsorbing a chemical analyte. The surface includes at least one conductive heating track for heating the chemical analyte and also a conductive response track, which is electrically isolated from the heating track, for producing a thermal response signal from the chemical analyte. The heating track is electrically connected with a voltage source and the response track is electrically connected with a signal recorder. The microscale body is restrained at the first end and the second end and is substantially isolated from its surroundings therebetween, thus having a bridge configuration.

  12. Micro faraday-element array detector for ion mobility spectroscopy

    DOE Patents [OSTI]

    Gresham, Christopher A.; Rodacy, Phillip J.; Denton, M. Bonner; Sperline, Roger

    2004-10-26

    An ion mobility spectrometer includes a drift tube having a collecting surface covering a collecting area at one end of the tube. The surface comprises a plurality of closely spaced conductive elements on a non-conductive substrate, each conductive element being electrically insulated from each other element. A plurality of capacitive transimpedance amplifiers (CTIA) adjacent the collecting surface are electrically connected to the plurality of elements, so charge from an ion striking an element is transferred to the capacitor of the connected CTIA. A controller counts the charge on the capacitors over a period of time.

  13. Mobilization of cohesive sludge in storage tanks using jet mixers

    SciTech Connect (OSTI)

    Poirier, M.R.

    2000-02-04

    The Pacific Northwest National Laboratory (PNNL), Savannah River Site and ITT Flygt Corporation conducted a joint mixer testing program sponsored by the DOE to evaluate the applicability of Flygt mixers to nuclear tank waste retrieval. Testing was carried out in three different tank sizes so that a scaling method could be evaluated and validated and the results could be used to make a full-scale mixer performance prediction. This presentation focuses on testing the mobilization of the sludge simulant composed of fine-grained particles cohesively bonded together by both colloidal and mechanical forces.

  14. ARM Mobile Facility Surface Meteorology Handbook - October 2008

    SciTech Connect (OSTI)

    MT Ritsche

    2008-10-30

    The ARM Mobile Facility Surface Meteorology station (AMF MET) uses mainly conventional in situ sensors to obtain 1-minute statistics of surface wind speed, wind direction, air temperature, relative humidity, barometric pressure, and rain-rate. Additional sensors may be added to or removed from the base set of sensors depending upon the deployment location, climate regime or programmatic needs. Additionally, sensor types may change depending upon the climate regime of the deployment. These changes/additions are noted in the Deployment Locations and History section.

  15. Evaluation of electron mobility in InSb quantum wells by means of percentage-impact

    SciTech Connect (OSTI)

    Mishima, T. D.; Edirisooriya, M.; Santos, M. B.

    2014-05-15

    In order to quantitatively analyze the contribution of each scattering factor toward the total carrier mobility, we use a new convenient figure-of-merit, named a percentage impact. The mobility limit due to a scattering factor, which is widely used to summarize a scattering analysis, has its own advantage. However, a mobility limit is not quite appropriate for the above purpose. A comprehensive understanding of the difference in contribution among many scattering factors toward the total carrier mobility can be obtained by evaluating percentage impacts of scattering factors, which can be straightforwardly calculated from their mobility limits and the total mobility. Our percentage impact analysis shows that threading dislocation is one of the dominant scattering factors for the electron transport in InSb quantum wells at room temperature.

  16. Tracking Living Cells as They Differentiate in Real Time

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tracking Living Cells as They Differentiate in Real Time Tracking Living Cells as They Differentiate in Real Time Print Thursday, 27 September 2012 00:00 Protein phosphorylation regulates protein function in a cell, either activating or inactivating the proteins responsible for many cell functions ranging from cell proliferation to differentiation to metabolism to signaling, and even programmed cell death. This chemical process has been studied intensively, but until now it has been impossible

  17. New mobile application allows users to take virtual tour of Project Y of

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Manhattan Project National Historical Park Manhattan Project National Historical Park mobile app New mobile application allows users to take virtual tour of Project Y of Manhattan Project National Historical Park A new, free mobile application is now available for download from the Apple store. June 7, 2016 the application allows users from any location around the world to experience the environment in that pivotal time during World War II when a group of scientists came to Project Y, the

  18. And the Oscar for Sustainable Mobile Lighting Goes to.... Lighting Up

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Operations with Hydrogen and Fuel Cell Technology | Department of Energy And the Oscar for Sustainable Mobile Lighting Goes to.... Lighting Up Operations with Hydrogen and Fuel Cell Technology And the Oscar for Sustainable Mobile Lighting Goes to.... Lighting Up Operations with Hydrogen and Fuel Cell Technology September 30, 2014 - 1:12pm Addthis Developed by Sandia National Laboratories and several industry partners, the fuel cell mobile light (H2LT) offers a cleaner, quieter alternative to

  19. DOE Science Showcase - Research on the "Go" with OSTI mobile | OSTI, US

    Office of Scientific and Technical Information (OSTI)

    Dept of Energy Office of Scientific and Technical Information Research on the "Go" with OSTI mobile Now you can find full-text technical reports from the Department of Energy from your mobile device. The new mobile OSTI website http://m.osti.gov/ is ready to travel and provides the latest research, OSTI news, award-winning OSTIblog, as well as OSTI YouTube, Facebook & Twitter interface whenever & wherever you need it.

  20. Tracking Living Cells as They Differentiate in Real Time

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tracking Living Cells as They Differentiate in Real Time Print Protein phosphorylation ... cells, enabling them to follow cellular chemical changes in real time, without bias. ...

  1. Tracking Living Cells as They Differentiate in Real Time

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tracking Living Cells as They Differentiate in Real Time Print Protein phosphorylation regulates protein function in a cell, either activating or inactivating the proteins...

  2. Differential pressure sensing system for airfoils usable in turbine engines

    DOE Patents [OSTI]

    Yang, Wen-Ching; Stampahar, Maria E.

    2005-09-13

    A detection system for identifying airfoils having a cooling systems with orifices that are plugged with contaminants or with showerheads having a portion burned off. The detection system measures pressures at different locations and calculates or measures a differential pressure. The differential pressure may be compared with a known benchmark value to determine whether the differential pressure has changed. Changes in the differential pressure may indicate that one or more of the orifices in a cooling system of an airfoil are plugged or that portions of, or all of, a showerhead has burned off.

  3. Software with Mobile Agents for Peer-to-Peer Information Sharing...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of failure. To avoid potential sudden system collapse, researchers at ORNL developed a Java-based mobile agent information software called Knowledge Acquisition Ubiquitous Agent...

  4. Enhancing the Electron Mobility via Delta-Doping in SrTiO3

    SciTech Connect (OSTI)

    Kozuka, Y.

    2011-08-11

    We fabricated high-mobility {delta}-doped structures in SrTiO{sub 3} thin films in order to investigate the low temperature electronic transport properties of confined carriers in this system. An enhancement of the electron mobility above the bulk value was observed as the doped layer thickness decreased. High-field Hall measurements revealed that this mobility enhancement originates from higher-mobility electrons in the undoped clean regions, which have quantum-mechanically broadened from the doped layer. Because of the absence of apparent lattice misfit between the layers, this structure is highly suitable for investigating two-dimensional electron gases in SrTiO{sub 3}

  5. OSTIblog Articles in the OSTI Mobile Topic | OSTI, US Dept of...

    Office of Scientific and Technical Information (OSTI)

    software, project summaries, patents, and e-prints... Related Topics: DOE Green Energy, DOepatents, Energy Citations Database (ECD), Information Bridge (IB), mobile, OSTI ...

  6. Title Plutonium Mobility in Soil and Uptake in Plants: A Review...

    National Nuclear Security Administration (NNSA)

    ... 98.2% of the adsorbed plutonium on soil samples from equilibrated solutions of plutonium ... possible plutonium mobility in the soil beneath one of the subsurface storage cribs. ...

  7. Signal-to-noise and resolution enhancement in ion mobility spectrometr...

    Office of Scientific and Technical Information (OSTI)

    in ion mobility spectrometry using correlation gating techniques : barker codes. ... Research Org: Sandia National Laboratories Sponsoring Org: USDOE Country of Publication: ...

  8. Nitrogen control of chloroplast differentiation. Final report

    SciTech Connect (OSTI)

    Schmidt, G.W.

    1998-05-01

    This project was directed toward understanding at the physiological, biochemical and molecular levels of how photosynthetic organisms adapt to long-term nitrogen-deficiency conditions is quite incomplete even though limitation of this nutrient is the most commonly restricts plant growth and development. For our work on this problem, the unicellular green alga, Chlamydomonas reinhardtii, was grown in continuous cultures in which steady-state levels of nitrogen can be precisely controlled. N-limited cells exhibit the classical symptoms of deficiency of this nutrient, chlorosis and slow growth rates, and respond to nitrogen provision by rapid greening and chloroplast differentiation. We have addressed three aspects of this problem: (1) the regulation of pigment synthesis; (2) control of expression of nuclear genes encoding photosynthetic proteins; (3) changes in metabolic and electron transport pathways that enable sustained CO{sub 2} fixation even though they cannot be readily converted into amino and nucleic acids. For the last, principle components are: (a) enhanced mitochondrial respiratory activity intimately associated with photosynthates, and (b) the occurrence in thylakoids of a supplemental electron transport pathway that facilitates reduction of the plastoquinone pool. Together, these distinguishing features of N-limited cells are likely to enable cell survival, especially under conditions of high irradiance stress.

  9. Stochastic differential equations and numerical simulation for pedestrians

    SciTech Connect (OSTI)

    Garrison, J.C.

    1993-07-27

    The mathematical foundation of the Ito interpretation of stochastic ordinary and partial differential equations is briefly explained. This provides the basis for a review of simple difference approximations to stochastic differential equations. An example arising in the theory of optical switching is discussed.

  10. Steerable vertical to horizontal energy transducer for mobile robots

    DOE Patents [OSTI]

    Spletzer, Barry L.; Fischer, Gary J.; Feddema, John T.

    2001-01-01

    The present invention provides a steerable vertical to horizontal energy transducer for mobile robots that less complex and requires less power than two degree of freedom tilt mechanisms. The present invention comprises an end effector that, when mounted with a hopping actuator, translates along axis (typically vertical) actuation into combined vertical and horizontal motion. The end effector, or foot, mounts with an end of the actuator that moves toward the support surface (typically a floor or the earth). The foot is shaped so that the first contact with the support surface is off the axis of the actuator. Off-axis contact with the support surface generates an on-axis force (typically resulting in vertical motion) and a moment orthogonal to the axis. The moment initiates a horizontal tumbling motion, and tilts the actuator so that its axis is oriented with a horizontal component and continued actuation generates both vertical and horizontal force.

  11. Mobility of indium on the ZnO(0001) surface

    SciTech Connect (OSTI)

    Heinhold, R.; Reeves, R. J.; Allen, M. W.; Williams, G. T.; Evans, D. A.

    2015-02-02

    The mobility of indium on the Zn-polar (0001) surface of single crystal ZnO wafers was investigated using real-time x-ray photoelectron spectroscopy. A sudden transition in the wettability of the ZnO(0001) surface was observed at ∼520 °C, with indium migrating from the (0001{sup ¯}) underside of the wafer, around the non-polar (11{sup ¯}00) and (112{sup ¯}0) sidewalls, to form a uniform self-organized (∼20 Å) adlayer. The In adlayer was oxidized, in agreement with the first principles calculations of Northrup and Neugebauer that In{sub 2}O{sub 3} precipitation can only be avoided under a combination of In-rich and Zn-rich conditions. These findings suggest that unintentional In adlayers may form during the epitaxial growth of ZnO on indium-bonded substrates.

  12. Nanolaminate microfluidic device for mobility selection of particles

    DOE Patents [OSTI]

    Surh, Michael P.; Wilson, William D.; Barbee, Jr., Troy W.; Lane, Stephen M.

    2006-10-10

    A microfluidic device made from nanolaminate materials that are capable of electrophoretic selection of particles on the basis of their mobility. Nanolaminate materials are generally alternating layers of two materials (one conducting, one insulating) that are made by sputter coating a flat substrate with a large number of layers. Specific subsets of the conducting layers are coupled together to form a single, extended electrode, interleaved with other similar electrodes. Thereby, the subsets of conducting layers may be dynamically charged to create time-dependent potential fields that can trap or transport charge colloidal particles. The addition of time-dependence is applicable to all geometries of nanolaminate electrophoretic and electrochemical designs from sinusoidal to nearly step-like.

  13. Compact and mobile high resolution PET brain imager

    DOE Patents [OSTI]

    Majewski, Stanislaw; Proffitt, James

    2011-02-08

    A brain imager includes a compact ring-like static PET imager mounted in a helmet-like structure. When attached to a patient's head, the helmet-like brain imager maintains the relative head-to-imager geometry fixed through the whole imaging procedure. The brain imaging helmet contains radiation sensors and minimal front-end electronics. A flexible mechanical suspension/harness system supports the weight of the helmet thereby allowing for patient to have limited movements of the head during imaging scans. The compact ring-like PET imager enables very high resolution imaging of neurological brain functions, cancer, and effects of trauma using a rather simple mobile scanner with limited space needs for use and storage.

  14. CoMRoS: Cooperative mobile robots Stuttgart

    SciTech Connect (OSTI)

    Braeunl, T.; Kalbacher, M.; Levi, P.; Mamier, G.

    1996-12-31

    Project CoMRoS has the goal to develop intelligent cooperating mobile robots. Several different vehicles are to solve a single task autonomously by exchanging plans without a central control. We use {open_quotes}Robuter II{close_quotes} vehicles from Robosoft France, adapted to our needs. The standard vehicle has very little local intelligence (VME bus system) and is controlled remotely by wireless Ethernet for sending steering commands and receiving sonar sensor data. A wireless video link is used to transmit camera images. Data exchange between vehicles is then performed among the corresponding workstations. The remote control is basically used to simplify testing and debugging of robot programs. However, each vehicle can also be driven completely autonomous by using a laptop PC.

  15. In-situ groundwater remediation by selective colloid mobilization

    DOE Patents [OSTI]

    Seaman, J.C.; Bertch, P.M.

    1998-12-08

    An in-situ groundwater remediation pump and treat technique is described which is effective for reclamation of aquifers that have been contaminated with a mixed, metal-containing waste, and which promotes selective mobilization of metal oxide colloids with a cationic surfactant, preferably a quaternary alkylammonium surfactant, without significantly reducing formation permeability that often accompanies large-scale colloid dispersion, thus increasing the efficiency of the remediation effort by enhancing the capture of strongly sorbing contaminants associated with the oxide phases. The resulting suspension can be separated from the bulk solution with controlled pH adjustments to destabilize the oxide colloids, and a clear supernatant which results that can be recycled through the injection well without further waste treatment. 3 figs.

  16. LESSONS LEARNED Biosurveillance Mobile App Development Intern Competition (Summer 2013)

    SciTech Connect (OSTI)

    Noonan, Christine F.; Henry, Michael J.; Corley, Courtney D.

    2014-01-14

    The purpose of the lessons learned document for the BEOWulf Biosurveillance Mobile App Development Intern Competition is to capture the project’s lessons learned in a formal document for use by other project managers on similar future projects. This document may be used as part of new project planning for similar projects in order to determine what problems occurred and how those problems were handled and may be avoided in the future. Additionally, this document details what went well with the project and why, so that other project managers may capitalize on these actions. Project managers may also use this document to determine who the project team members were in order to solicit feedback for planning their projects in the future. This document will be formally communicated with the organization and will become a part of the organizational assets and archives.

  17. PO*WW*ER mobile treatment unit process hazards analysis

    SciTech Connect (OSTI)

    Richardson, R.B.

    1996-06-01

    The objective of this report is to demonstrate that a thorough assessment of the risks associated with the operation of the Rust Geotech patented PO*WW*ER mobile treatment unit (MTU) has been performed and documented. The MTU was developed to treat aqueous mixed wastes at the US Department of Energy (DOE) Albuquerque Operations Office sites. The MTU uses evaporation to separate organics and water from radionuclides and solids, and catalytic oxidation to convert the hazardous into byproducts. This process hazards analysis evaluated a number of accident scenarios not directly related to the operation of the MTU, such as natural phenomena damage and mishandling of chemical containers. Worst case accident scenarios were further evaluated to determine the risk potential to the MTU and to workers, the public, and the environment. The overall risk to any group from operation of the MTU was determined to be very low; the MTU is classified as a Radiological Facility with low hazards.

  18. Dynamic multiplexed analysis method using ion mobility spectrometer

    DOE Patents [OSTI]

    Belov, Mikhail E [Richland, WA

    2010-05-18

    A method for multiplexed analysis using ion mobility spectrometer in which the effectiveness and efficiency of the multiplexed method is optimized by automatically adjusting rates of passage of analyte materials through an IMS drift tube during operation of the system. This automatic adjustment is performed by the IMS instrument itself after determining the appropriate levels of adjustment according to the method of the present invention. In one example, the adjustment of the rates of passage for these materials is determined by quantifying the total number of analyte molecules delivered to the ion trap in a preselected period of time, comparing this number to the charge capacity of the ion trap, selecting a gate opening sequence; and implementing the selected gate opening sequence to obtain a preselected rate of analytes within said IMS drift tube.

  19. In-situ groundwater remediation by selective colloid mobilization

    DOE Patents [OSTI]

    Seaman, John C. (New Ellenton, SC); Bertch, Paul M. (Aiken, SC)

    1998-01-01

    An in-situ groundwater remediation pump and treat technique effective for reclamation of aquifers that have been contaminated with a mixed, metal-containing waste, which promotes selective mobilization of metal oxide colloids with a cationic surfactant, preferably a quaternary alkylammonium surfactant, without significantly reducing formation permeability that often accompanies large-scale colloid dispersion, thus increasing the efficiency of the remediation effort by enhancing the capture of strongly sorbing contaminants associated with the oxide phases. The resulting suspension can be separated from the bulk solution with controlled pH adjustments to destabilize the oxide colloids, and a clear supernatant which results that can be recycled through the injection well without further waste treatment.

  20. Photoinduced translational molecular mobility in solid nanostructured azo dye films

    SciTech Connect (OSTI)

    Ezhov, A A; Kozenkov, V M; Magnitskii, Sergey A; Nagorskii, Nikolay M; Panov, Vladimir I

    2011-11-30

    A new mechanism controlling the molecular motion in thin azo-containing films during a photoinduced change in the surface nanorelief is found. It is shown experimentally that exposure of a solid AD-1 azo dye, deposited on a glass substrate, to incoherent linearly polarised light leads to formation of nanostructures with a characteristic size of 200 nm, which are similar to droplets of melt of this dye on the same substrate. It is shown that photoinduced mass transport in a solid AD-1 azo dye film can be explained by the mobility of molecules related to their trans-cis-photoisomerisation, which leads to film softening with subsequent formation of spherical protrusions under surface tension forces.

  1. A mobile computed tomographic unit for inspecting reinforced concrete columns

    SciTech Connect (OSTI)

    Sumitra, T.; Srisatit, S.; Pattarasumunt, A.

    1994-12-31

    A mobile computed tomographic unit applicable in the inspection of reinforced concrete columns was designed, constructed and tested. A CT image reconstruction programme written in Quick Basic was first developed to be used on an IBM PC/AT microcomputer. It provided user friendly menus for data processing and displaying CT image. The prototype of a gamma-ray scanning system using a 1.11 GBq Cs-137 source and a NaI(T1) scintillation detector was also designed and constructed. The system was a microcomputer controlled, single-beam rotate-translate scanner used for collecting transmitted gamma-ray data in different angles. The CT unit was finally tested with a standard column and a column of an existing building. The cross sectional images of the columns could be clearly seen. The positions and sizes of the reinforced bars could be estimated.

  2. Apolipoprotein E promotes lipid accumulation and differentiation in human adipocytes

    SciTech Connect (OSTI)

    Lasrich, Dorothee; Bartelt, Alexander; Grewal, Thomas; Heeren, Joerg

    2015-09-10

    Several studies in mice indicate a role for apolipoprotein E (APOE) in lipid accumulation and adipogenic differentiation in adipose tissue. However, little is yet known if APOE functions in a similar manner in human adipocytes. This prompted us to compare lipid loading and expression of adipocyte differentiation markers in APOE-deficient and control adipocytes using the differentiated human mesenchymal stem cell line hMSC-Tert as well as primary human and mouse adipocytes as model systems. Differentiated hMSC-Tert were stably transduced with or without siRNA targeting APOE while murine adipocytes were isolated from wild type and Apoe knockout mice. Human APOE knockdown hMSC-Tert adipocytes accumulated markedly less triglycerides compared to control cells. This correlated with strongly decreased gene expression levels of adipocyte markers such as adiponectin (ADIPOQ) and fatty acid binding protein 4 (FABP4) as well as the key transcription factor driving adipocyte differentiation, peroxisome proliferator activator receptor gamma (PPARG), in particular the PPARG2 isoform. Similarly, differentiation of murine Apoe-deficient adipocytes was characterized by reduced gene expression of Adipoq, Fabp4 and Pparg. Interestingly, incubation of APOE-deficient hMSC-Tert adipocytes with conditioned media from APOE3-overexpressing adipocytes or APOE-containing Very Low Density Lipoprotein (VLDL) partially restored triglyceride accumulation, but were unable to induce adipocyte differentiation, as judged by expression of adipocyte markers. Taken together, depletion of endogenous APOE in human adipocytes severely impairs lipid accumulation, which is associated with an inability to initiate differentiation. - Highlights: • Immortalized human mesenchymal stem cells were used to study adipocyte development. • Knockdown of endogenous APOE lead to impaired lipid accumulation and adipogenesis. • APOE supplementation partially restored lipid accumulation but not differentiation.

  3. Reversible differentiation of myofibroblasts by MyoD

    SciTech Connect (OSTI)

    Hecker, Louise; Jagirdar, Rajesh; Jin, Toni; Thannickal, Victor J.

    2011-08-01

    Myofibroblasts participate in tissue repair processes in diverse mammalian organ systems. The deactivation of myofibroblasts is critical for termination of the reparative response and restoration of tissue structure and function. The current paradigm on normal tissue repair is the apoptotic clearance of terminally differentiated myofibroblasts; while, the accumulation of activated myofibroblasts is associated with progressive human fibrotic disorders. The capacity of myofibroblasts to undergo de-differentiation as a potential mechanism for myofibroblast deactivation has not been examined. In this report, we have uncovered a role for MyoD in the induction of myofibroblast differentiation by transforming growth factor-{beta}1 (TGF-{beta}1). Myofibroblasts demonstrate the capacity for de-differentiation and proliferation by modulation of endogenous levels of MyoD. We propose a model of reciprocal signaling between TGF-{beta}1/ALK5/MyoD and mitogen(s)/ERK-MAPK/CDKs that regulate myofibroblast differentiation and de-differentiation, respectively. Our studies provide the first evidence for MyoD in controlling myofibroblast activation and deactivation. Restricted capacity for de-differentiation of myofibroblasts may underlie the progressive nature of recalcitrant human fibrotic disorders.

  4. Differential geometry on Hopf algebras and quantum groups

    SciTech Connect (OSTI)

    Watts, P.

    1994-12-15

    The differential geometry on a Hopf algebra is constructed, by using the basic axioms of Hopf algebras and noncommutative differential geometry. The space of generalized derivations on a Hopf algebra of functions is presented via the smash product, and used to define and discuss quantum Lie algebras and their properties. The Cartan calculus of the exterior derivative, Lie derivative, and inner derivation is found for both the universal and general differential calculi of an arbitrary Hopf algebra, and, by restricting to the quasitriangular case and using the numerical R-matrix formalism, the aforementioned structures for quantum groups are determined.

  5. A Unified Differential Evolution Algorithm for Global Optimization

    SciTech Connect (OSTI)

    Qiang, Ji; Mitchell, Chad

    2014-06-24

    Abstract?In this paper, we propose a new unified differential evolution (uDE) algorithm for single objective global optimization. Instead of selecting among multiple mutation strategies as in the conventional differential evolution algorithm, this algorithm employs a single equation as the mutation strategy. It has the virtue of mathematical simplicity and also provides users the flexbility for broader exploration of different mutation strategies. Numerical tests using twelve basic unimodal and multimodal functions show promising performance of the proposed algorithm in comparison to convential differential evolution algorithms.

  6. Case Study: Mobile Photovoltaic System at Bechler Meadows Ranger Station, Yellowstone National Park (Brochure), Federal Energy Management Program (FEMP)

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Mobile Photovoltaic System at Bechler Meadows Ranger Station, Yellowstone National Park Introduction This report describes the performance of a mobile photovoltaic (PV) system installed in 2011 to provide power to Bechler Ranger Station in Yellowstone National Park, Wyo. This small, remote outpost is not served by the electric utility grid and previously relied on a propane generator as the only source of power. Mobile Photovoltaic Systems Mobile solar systems consist of photovoltaic (PV)

  7. ARM - VAP Process - tdmadap

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productstdmadap Documentation & Plots tdmadap : XDC documentation Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Aerosol Properties derived from TDMA Measurements (TDMADAP) Instrument Categories Aerosols Output Products tdmaccncoll : Tandem Differential Mobility Analyzer: Cloud Condensation Nuclei -- D. Collins Primary Measurements The following measurements

  8. ARM - Facility News Article

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    April 30, 2010 [Data Announcements, Facility News] Tandem Differential Mobility Analyzer (TDMA) Data Available at the ARM Data Archive Bookmark and Share Dry samples are collected by the aerosol stack and transferred inside the Aerosol Observation System structure to the TDMA where they are exposed to humidity for growth rate sampling. For more details on how the TDMA works, see this schematic. Dry samples are collected by the aerosol stack and transferred inside the Aerosol Observation System

  9. Electrorecycling of Critical and Value Metals from Mobile Electronics

    SciTech Connect (OSTI)

    Lister, Tedd E.; Wang, Peming; Anderko, Andre

    2014-09-01

    Mobile electronic devices such as smart phones and tablets are a significant source of valuable metals that should be recycled. Each year over a billion devices are sold world-wide and the average life is only a couple years. Value metals in phones are gold, palladium, silver, copper, cobalt and nickel. Devices now contain increasing amounts of rare earth elements (REE). In recent years the supply chain for REE has moved almost exclusively to China. They are contained in displays, speakers and vibrators within the devices. By US Department of Energy (DOE) classification, specific REEs (Nd, Dy, Eu, Tb and Y) are considered critical while others (Ce, La and Pr) are deemed near critical. Effective recycling schemes should include the recovery of these critical materials. By including more value materials in a recovery scheme, more value can be obtained by product diversification and less waste metals remains to be disposed of. REEs are mined as a group such that when specific elements become critical significantly more ore must be processed to capture the dilute but valuable critical elements. Targeted recycling of items containing the more of the less available critical materials could address their future criticality. This presentation will describe work in developing aqueous electrochemistry-based schemes for recycling metals from scrap mobile electronics. The electrorecycling process generates oxidizing agents at an anode while reducing dissolved metals at the cathode. E vs pH diagrams and metals dissolution experiments are used to assess effectiveness of various solution chemistries. Although several schemes were envisioned, a two stages process has been the focus of work: 1) initial dissolution of Cu, Sn, Ag and magnet materials using Fe+3 generated in acidic sulfate and 2) final dissolution of Pd and Au using Cl2 generated in an HCl solution. Experiments were performed using simulated metal mixtures. Both Cu and Ag were recovered at ~ 97% using Fe+3 while

  10. Surfactant Based Enhanced Oil Recovery and Foam Mobility Control

    SciTech Connect (OSTI)

    George J. Hirasaki; Clarence A. Miller

    2006-09-09

    Surfactant flooding has the potential to significantly increase recovery over that of conventional waterflooding. The availability of a large number of surfactant structures makes it possible to conduct a systematic study of the relation between surfactant structure and its efficacy for oil recovery. A mixture of two surfactants was found to be particularly effective for application in carbonate formations at low temperature. The mixture is single phase for higher salinity or calcium concentrations than that for either surfactant used alone. This makes it possible to inject the surfactant slug with polymer close to optimal conditions and yet be single phase. A formulation has been designed for a particular field application. It uses partially hydrolyzed polyacrylamide for mobility control. The addition of an alkali such as sodium carbonate makes possible in situ generation of naphthenic soap and significant reduction of synthetic surfactant adsorption. The design of the process to maximize the region of ultra-low IFT takes advantage of the observation that the ratio of soap to synthetic surfactant is a parameter in the conditions for optimal salinity. Even for a fixed ratio of soap to surfactant, the range of salinity for low IFT was wider than that reported for surfactant systems in the literature. Low temperature, forced displacement experiments in dolomite and silica sandpacks demonstrate that greater than 95% recovery of the waterflood remaining oil is possible with 0.2% surfactant concentration, 0.5 PV surfactant slug, with no alcohol. Compositional simulation of the displacement process demonstrates the role of soap/surfactant ratio on passage of the profile through the ultralow IFT region, the importance of a wide salinity range of low IFT, and the importance of the viscosity of the surfactant slug. Mobility control is essential for surfactant EOR. Foam is evaluated to improve the sweep efficiency of surfactant injected into fractured reservoirs as well as a

  11. Pilot Project Technology Business Case: Mobile Work Packages

    SciTech Connect (OSTI)

    Thomas, Ken; Lawrie, Sean; Niedermuller, Josef

    2015-05-01

    Performance advantages of the new pilot project technologies are widely acknowledged, but it has proven difficult for utilities to derive business cases for justifying investment in these new capabilities. Lack of a business case is often cited by utilities as a barrier to pursuing wide-scale application of digital technologies to nuclear plant work activities. The decision to move forward with funding usually hinges on demonstrating actual cost reductions that can be credited to budgets and thereby truly reduce O&M or capital costs. Technology enhancements, while enhancing work methods and making work more efficient, often fail to eliminate workload such that it changes overall staffing and material cost requirements. It is critical to demonstrate cost reductions or impacts on non-cost performance objectives in order for the business case to justify investment by nuclear operators. The Business Case Methodology (BCM) was developed in September of 2015 to frame the benefit side of II&C technologies to address the “benefit” side of the analysis—as opposed to the cost side—and how the organization evaluates discretionary projects (net present value (NPV), accounting effects of taxes, discount rates, etc.). The cost and analysis side is not particularly difficult for the organization and can usually be determined with a fair amount of precision (not withstanding implementation project cost overruns). It is in determining the “benefits” side of the analysis that utilities have more difficulty in technology projects and that is the focus of this methodology. The methodology is presented in the context of the entire process, but the tool provided is limited to determining the organizational benefits only. This report describes a the use of the BCM in building a business case for mobile work packages, which includes computer-based procedures and other automated elements of a work package. Key to those impacts will be identifying where the savings are

  12. Method for HEPA filter leak scanning with differentiating aerosol detector

    SciTech Connect (OSTI)

    Kovach, B.J.; Banks, E.M.; Wikoff, W.O.

    1997-08-01

    While scanning HEPA filters for leaks with {open_quotes}Off the Shelf{close_quote} aerosol detection equipment, the operator`s scanning speed is limited by the time constant and threshold sensitivity of the detector. This is based on detection of the aerosol density, where the maximum signal is achieved when the scanning probe resides over the pinhole longer than several detector time-constants. Since the differential value of the changing signal can be determined by observing only the first small fraction of the rising signal, using a differentiating amplifier will speed up the locating process. The other advantage of differentiation is that slow signal drift or zero offset will not interfere with the process of locating the leak, since they are not detected. A scanning hand-probe attachable to any NUCON{reg_sign} Aerosol Detector displaying the combination of both aerosol density and differentiated signal was designed. 3 refs., 1 fig.

  13. Tracking Living Cells as They Differentiate in Real Time

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tracking Living Cells as They Differentiate in Real Time Print Protein phosphorylation regulates protein function in a cell, either activating or inactivating the proteins responsible for many cell functions ranging from cell proliferation to differentiation to metabolism to signaling, and even programmed cell death. This chemical process has been studied intensively, but until now it has been impossible to watch phosphorylation at the molecular level without damaging cells or interfering with

  14. Tracking Living Cells as They Differentiate in Real Time

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tracking Living Cells as They Differentiate in Real Time Print Protein phosphorylation regulates protein function in a cell, either activating or inactivating the proteins responsible for many cell functions ranging from cell proliferation to differentiation to metabolism to signaling, and even programmed cell death. This chemical process has been studied intensively, but until now it has been impossible to watch phosphorylation at the molecular level without damaging cells or interfering with

  15. Differential form of the Skornyakov-Ter-Martirosyan Equations

    SciTech Connect (OSTI)

    Pen'kov, F. M.; Sandhas, W.

    2005-12-15

    The Skornyakov-Ter-Martirosyan three-boson integral equations in momentum space are transformed into differential equations. This allows us to take into account quite directly the Danilov condition providing self-adjointness of the underlying three-body Hamiltonian with zero-range pair interactions. For the helium trimer the numerical solutions of the resulting differential equations are compared with those of the Faddeev-type AGS equations.

  16. Tracking Living Cells as They Differentiate in Real Time

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tracking Living Cells as They Differentiate in Real Time Print Protein phosphorylation regulates protein function in a cell, either activating or inactivating the proteins responsible for many cell functions ranging from cell proliferation to differentiation to metabolism to signaling, and even programmed cell death. This chemical process has been studied intensively, but until now it has been impossible to watch phosphorylation at the molecular level without damaging cells or interfering with

  17. Tracking Living Cells as They Differentiate in Real Time

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tracking Living Cells as They Differentiate in Real Time Print Protein phosphorylation regulates protein function in a cell, either activating or inactivating the proteins responsible for many cell functions ranging from cell proliferation to differentiation to metabolism to signaling, and even programmed cell death. This chemical process has been studied intensively, but until now it has been impossible to watch phosphorylation at the molecular level without damaging cells or interfering with

  18. Tracking Living Cells as They Differentiate in Real Time

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tracking Living Cells as They Differentiate in Real Time Print Protein phosphorylation regulates protein function in a cell, either activating or inactivating the proteins responsible for many cell functions ranging from cell proliferation to differentiation to metabolism to signaling, and even programmed cell death. This chemical process has been studied intensively, but until now it has been impossible to watch phosphorylation at the molecular level without damaging cells or interfering with

  19. Pipeline integrity design for differential settlement in discontinuous permafrost areas

    SciTech Connect (OSTI)

    Zhou, Z.J.; Boivin, R.P.; Glover, A.G.; Kormann, P.J.

    1996-12-31

    The NOVA Gas Transmission Ltd. (NGTL) gas pipeline system is expanding northwards as the producers search for and find new gas reserves. This growth has taken the system into the discontinuous permafrost zone, and also into new design problems. One such problem is the structural integrity of a pipeline subjected to the settlement differentials that occur between frozen and unfrozen soils. Adequate integrity design for differential settlement is required by design codes, such as CSA Z662, but the procedures and criteria must be established by the pipeline designers. This paper presents the methodology of pipeline integrity design for differential settlements used on a number of pipeline projects in Northwest Alberta. Outlined in the paper are the procedures, rationales and models used to: (a) locate discontinuous permafrost; (b) quantify the potential differential settlement; (c) predict pipeline stresses and strains; (d) establish strain limits; and (e) determine the pipe wall thickness to withstand those potential differential settlements. Several design options are available and are briefly discussed. For the projects mentioned, the heavy wall pipe option was identified as a cost effective design for medium to large differential settlements.

  20. Lightweight Integrated Optical Sensor for Atmospheric Measurements on Mobile Platforms

    SciTech Connect (OSTI)

    Parameswaran, Krishnan R.

    2013-12-02

    The goal of the Phase I program was to develop a novel open path sensor platform technology based on integration of semiconductor waveguides with efficient optoelectronic components on a monolithic platform. The successful Phase I effort resulted in demonstration of a novel optical resonator structure based on semiconductor high contrast gratings (HCGs) that will enable implementation of an ultra-compact, low-power gas sensor suitable for use on mobile platforms. Extensive numerical modeling was performed to design a device optimized for measuring CO2 at a wavelength for which a laser was available for proof of concept. Devices were fabricated and tested to match the target wavelength, angle, and operating temperature. This demonstration is the first implementation of HCGs at the wavelengths of interest and shows the flexibility of the proposed architecture for gas sensing applications. The measured cavity Q was lower than anticipated due to fabrication process challenges. The PSI and UC Berkeley team has identified solutions to these challenges and will produce optimized devices in a Phase II program where a prototype sensor will be fabricated and tested.

  1. Mobile Nondestructive Assay (NDA) Measurements of Standard Waste Boxes (SWB)

    SciTech Connect (OSTI)

    Mozhayev, Andrey V.; Berg, Randal K.; Haggard, Daniel L.; Hilliard, James R.; Mapili, Gabriel M.

    2006-11-01

    A mobile NDA system was composed and qualified for Safeguards measurements of multiple standard waste boxes (SWB) generated as a result of clean-out activities at Hanford’s Plutonium Finishing Plant (PFP). The system included a neutron slab counter and high purity germanium (HPGe) detector. PC/FRAM software was used to determine the isotopic composition of plutonium residue contained in the waste in order to interpret two independent measurement results provided by total neutron counting and gamma energy analysis (GEA). The measurement procedure developed to estimate transuranic (TRU) content of boxes was based on assumptions about characteristics of the matrix and material distribution. The neutron slab counter was calibrated with various plutonium working standards that were placed in a surrogate SWB specifically made to simulate miscellaneous waste debris. Transmission measurements with a californium source were used to correct for the matrix effects. An In-Situ Object Counting System (ISOCS) was used to acquire spectra from SWBs and ISOCS software was applied to generate the efficiency curve of the HPGe detector. Infinite energy extrapolation was introduced to correct GEA results for self-attenuation. The gamma and neutron results obtained on multiple SWBs are compared and discussed in the paper. Revised measurement positions for the detector and the transmission source are also suggested based on experience gained during the measurements.

  2. Gating of high-mobility InAs metamorphic heterostructures

    SciTech Connect (OSTI)

    Shabani, J.; McFadden, A. P.; Shojaei, B.; Palmstrøm, C. J.

    2014-12-29

    We investigate the performance of gate-defined devices fabricated on high mobility InAs metamorphic heterostructures. We find that heterostructures capped with In{sub 0.75}Ga{sub 0.25}As often show signs of parallel conduction due to proximity of their surface Fermi level to the conduction band minimum. Here, we introduce a technique that can be used to estimate the density of this surface charge that involves cool-downs from room temperature under gate bias. We have been able to remove the parallel conduction under high positive bias, but achieving full depletion has proven difficult. We find that by using In{sub 0.75}Al{sub 0.25}As as the barrier without an In{sub 0.75}Ga{sub 0.25}As capping, a drastic reduction in parallel conduction can be achieved. Our studies show that this does not change the transport properties of the quantum well significantly. We achieved full depletion in InAlAs capped heterostructures with non-hysteretic gating response suitable for fabrication of gate-defined mesoscopic devices.

  3. Recovery Act: Advanced Direct Methanol Fuel Cell for Mobile Computing

    SciTech Connect (OSTI)

    Fletcher, James H.; Cox, Philip; Harrington, William J; Campbell, Joseph L

    2013-09-03

    ABSTRACT Project Title: Recovery Act: Advanced Direct Methanol Fuel Cell for Mobile Computing PROJECT OBJECTIVE The objective of the project was to advance portable fuel cell system technology towards the commercial targets of power density, energy density and lifetime. These targets were laid out in the DOE’s R&D roadmap to develop an advanced direct methanol fuel cell power supply that meets commercial entry requirements. Such a power supply will enable mobile computers to operate non-stop, unplugged from the wall power outlet, by using the high energy density of methanol fuel contained in a replaceable fuel cartridge. Specifically this project focused on balance-of-plant component integration and miniaturization, as well as extensive component, subassembly and integrated system durability and validation testing. This design has resulted in a pre-production power supply design and a prototype that meet the rigorous demands of consumer electronic applications. PROJECT TASKS The proposed work plan was designed to meet the project objectives, which corresponded directly with the objectives outlined in the Funding Opportunity Announcement: To engineer the fuel cell balance-of-plant and packaging to meet the needs of consumer electronic systems, specifically at power levels required for mobile computing. UNF used existing balance-of-plant component technologies developed under its current US Army CERDEC project, as well as a previous DOE project completed by PolyFuel, to further refine them to both miniaturize and integrate their functionality to increase the system power density and energy density. Benefits of UNF’s novel passive water recycling MEA (membrane electrode assembly) and the simplified system architecture it enabled formed the foundation of the design approach. The package design was hardened to address orientation independence, shock, vibration, and environmental requirements. Fuel cartridge and fuel subsystems were improved to ensure effective fuel

  4. SURFACTANT BASED ENHANCED OIL RECOVERY AND FOAM MOBILITY CONTROL

    SciTech Connect (OSTI)

    George J. Hirasaki; Clarence A. Miller; Gary A. Pope; Richard E. Jackson

    2004-07-01

    Surfactant flooding has the potential to significantly increase recovery over that of conventional waterflooding. The availability of a large number of surfactants makes it possible to conduct a systematic study of the relation between surfactant structure and its efficacy for oil recovery. Also, the addition of an alkali such as sodium carbonate makes possible in situ generation of surfactant and significant reduction of surfactant adsorption. In addition to reduction of interfacial tension to ultra-low values, surfactants and alkali can be designed to alter wettability to enhance oil recovery. An alkaline surfactant process is designed to enhance spontaneous imbibition in fractured, oil-wet, carbonate formations. It is able to recover oil from dolomite core samples from which there was no oil recovery when placed in formation brine. Mobility control is essential for surfactant EOR. Foam is evaluted to improve the sweep efficiency of surfactant injected into fractured reservoirs. UTCHEM is a reservoir simulator specially designed for surfactant EOR. A dual-porosity version is demonstrated as a potential scale-up tool for fractured reservoirs.

  5. Deep porosity preservation in the Norphlet Formation, Mobil Bay, Alabama

    SciTech Connect (OSTI)

    Ajdukiewicz, J.M.; Paxton, S.T.; Szabvo, J.O. )

    1991-03-01

    Compaction and pressure solution have commonly been assumed to destroy primary intergranular porosity in deeply buried sandstones. However, primary porosities of up to 20% are preserved at depths greater than 20,000 feet in the Norphlet Formation of Mobile Bay. Previous workers have called upon a number of mechanisms to preserve these high porosities in the Norphlet, specifically chlorite rim cements, gas emplacement, overpressuring, and decementation. In contrast, our study of data from 23 Norphlet wells, including 450 thin sections, indicates that these suggested mechanisms are not the primary cause of porosity preservation in the Norphlet. The authors propose an alternative interpretation: that in the Norphlet, as in other well-sorted, ductile-grain-poor sandstones, porosity loss from compaction did not go to completion under reservoir (premetamorphic) conditions, but stabilized at depths of about 5,000-8,000 feet and porosity values of about 26%. Porosity loss below these values is due to cementation. For cementation to occur, both an adequate source of cement and geochemical conditions favoring cement precipitation must be present. Computer simulations of Norphlet burial history, including post-depositional fluid-flow patterns, suggest that conditions favorable to quartz cementation never occurred in the bulk of the Norphlet because of the formation's stratigraphic position and isolation from a basinward source of silica-saturated fluids.

  6. Energy Savings Tips on the Go: Check Out the New Energy Savers Mobile Site

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy Savings Tips on the Go: Check Out the New Energy Savers Mobile Site Energy Savings Tips on the Go: Check Out the New Energy Savers Mobile Site March 16, 2012 - 12:46pm Addthis Chris Stewart Senior Communicator at DOE's National Renewable Energy Laboratory For years, many of you have found energy-saving tips about how to save money and energy at home, in your vehicle, and at work on our EnergySavers desktop site. This month, we launched a new Energy Savers mobile

  7. Effect of the mobility on (I-V) characteristics of the MOSFET

    SciTech Connect (OSTI)

    Benzaoui, Ouassila; Azizi, Cherifa

    2013-12-16

    MOSFET Transistor was the subject of many studies and research works (electronics, data-processing, telecommunications...) in order to exploit its interesting and promising characteristics. The aim of this contribution is devoted to the effect of the mobility on the static characteristics I-V of the MOSFET. The study enables us to calculate the drain current as function of bias in both linear and saturated modes; this effect is evaluated using a numerical simulation program. The influence of mobility was studied. Obtained results allow us to determine the mobility law in the MOSFET which gives optimal (I-V) characteristics of the component.

  8. Temperature dependence of diffusion length, lifetime and minority electron mobility in GaInP

    SciTech Connect (OSTI)

    Schultes, F. J.; Haegel, N. M.; Christian, T.; Alberi, K.; Fluegel, B.; Jones-Albertus, R.; Pickett, E.; Liu, T.; Misra, P.; Sukiasyan, A.; Yuen, H.

    2013-12-09

    The mobility of electrons in double heterostructures of p-type Ga{sub 0.50}In{sub 0.50}P has been determined by measuring minority carrier diffusion length and lifetime. The minority electron mobility increases monotonically from 300?K to 5?K, limited primarily by optical phonon and alloy scattering. Comparison to majority electron mobility over the same temperature range in comparably doped samples shows a significant reduction in ionized impurity scattering at lower temperatures, due to differences in interaction of repulsive versus attractive carriers with ionized dopant sites. These results should be useful in modeling and optimization for multi-junction solar cells and other optoelectronic devices.

  9. Multi-matrix, dual polarity, tandem mass spectrometry imaging strategy applied to a germinated maize seed: toward mass spectrometry imaging of an untargeted metabolome

    SciTech Connect (OSTI)

    Feenstra, Adam D.; Hansen, Rebecca L.; Lee, Young Jin

    2015-08-27

    Mass spectrometry imaging (MSI) provides high spatial resolution information that is unprecedented in traditional metabolomics analyses; however, the molecular coverage is often limited to a handful of compounds and is insufficient to understand overall metabolomic changes of a biological system. Here, we propose an MSI methodology to increase the diversity of chemical compounds that can be imaged and identified, in order to eventually perform untargeted metabolomic analysis using MSI. We use the desorption/ionization bias of various matrixes for different metabolite classes along with dual polarities and a tandem MSI strategy. The use of multiple matrixes and dual polarities allows us to visualize various classes of compounds, while data-dependent MS/MS spectra acquired in the same MSI scans allow us to identify the compounds directly on the tissue. In a proof of concept application to a germinated corn seed, a total of 166 unique ions were determined to have high-quality MS/MS spectra, without counting structural isomers, of which 52 were identified as unique compounds. According to an estimation based on precursor MSI datasets, we expect over five hundred metabolites could be potentially identified and visualized once all experimental conditions are optimized and an MS/MS library is available. Finally, metabolites involved in the glycolysis pathway and tricarboxylic acid cycle were imaged to demonstrate the potential of this technology to better understand metabolic biology.

  10. Multi-matrix, dual polarity, tandem mass spectrometry imaging strategy applied to a germinated maize seed: toward mass spectrometry imaging of an untargeted metabolome

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Feenstra, Adam D.; Hansen, Rebecca L.; Lee, Young Jin

    2015-08-27

    Mass spectrometry imaging (MSI) provides high spatial resolution information that is unprecedented in traditional metabolomics analyses; however, the molecular coverage is often limited to a handful of compounds and is insufficient to understand overall metabolomic changes of a biological system. Here, we propose an MSI methodology to increase the diversity of chemical compounds that can be imaged and identified, in order to eventually perform untargeted metabolomic analysis using MSI. We use the desorption/ionization bias of various matrixes for different metabolite classes along with dual polarities and a tandem MSI strategy. The use of multiple matrixes and dual polarities allows usmore » to visualize various classes of compounds, while data-dependent MS/MS spectra acquired in the same MSI scans allow us to identify the compounds directly on the tissue. In a proof of concept application to a germinated corn seed, a total of 166 unique ions were determined to have high-quality MS/MS spectra, without counting structural isomers, of which 52 were identified as unique compounds. According to an estimation based on precursor MSI datasets, we expect over five hundred metabolites could be potentially identified and visualized once all experimental conditions are optimized and an MS/MS library is available. Finally, metabolites involved in the glycolysis pathway and tricarboxylic acid cycle were imaged to demonstrate the potential of this technology to better understand metabolic biology.« less

  11. Design scoping study of the 12T Yin-Yang magnet system for the Tandem Mirror Next Step (TMNS). Final report

    SciTech Connect (OSTI)

    Not Available

    1981-09-01

    The overall objective of this engineering study was to determine the feasibility of designing a Yin-Yang magnet capable of producing a peak field in the windings of 12T for the Tandem Mirror Next Step (TMNS) program. As part of this technical study, a rough order of magnitude (ROM) cost estimate of the winding for this magnet was undertaken. The preferred approach to the winding design of the TMNS plug coil utilizes innovative design concepts to meet the structural, electrical and thermodynamic requirements of the magnet system. Structurally, the coil is radially partitioned into four sections, preventing the accumulation of the radial loads and reacting them into the structural case. To safely dissipate the 13.34 GJ of energy stored in each Yin-Yang magnet, the winding has been electrically subdivided into parallel or nested coils, each having its own power supply and protection circuitry. This arrangement effectively divides the total stored energy of the coils into manageable subsystems. The windings are cooled with superfluid helium II, operated at 1.8K and 1.2 atmospheres. The superior cooling capabilities of helium II have enabled the overall winding envelope to be minimized, providing a current density of 2367 A/CM/sup 2/, excluding substructure.

  12. Advantage of suppressed non-Langevin recombination in low mobility organic solar cells

    SciTech Connect (OSTI)

    Stolterfoht, Martin; Armin, Ardalan; Pandey, Ajay K.; Burn, Paul L.; Meredith, Paul; Pivrikas, Almantas; Philippa, Bronson; White, Ronald D.

    2014-07-07

    Photovoltaic performance in relation to charge transport is studied in efficient (7.6%) organic solar cells (PTB7:PC{sub 71}BM). Both electron and hole mobilities are experimentally measured in efficient solar cells using the resistance dependent photovoltage technique, while the inapplicability of classical techniques, such as space charge limited current and photogenerated charge extraction by linearly increasing voltage is discussed. Limits in the short-circuit current originate from optical losses, while charge transport is shown not to be a limiting process. Efficient charge extraction without recombination can be achieved with a mobility of charge carriers much lower than previously expected. The presence of dispersive transport with strongly distributed mobilities in high efficiency solar cells is demonstrated. Reduced non-Langevin recombination is shown to be beneficial for solar cells with imbalanced, low, and dispersive electron and hole mobilities.

  13. Thermal decomposition of electronic wastes: Mobile phone case and other parts

    SciTech Connect (OSTI)

    Molto, Julia; Egea, Silvia; Conesa, Juan Antonio; Font, Rafael

    2011-12-15

    Highlights: > Pyrolysis and combustion of different parts of mobile phones produce important quantities of CO and CO{sub 2}. > Naphthalene is the most abundant PAH obtained in the thermal treatment of mobile phones. > Higher combustion temperature increases the chlorinated species evolved. - Abstract: Pyrolysis and combustion runs at 850 {sup o}C in a horizontal laboratory furnace were carried out on different parts of a mobile phone (printed circuit board, mobile case and a mixture of both materials). The analyses of the carbon oxides, light hydrocarbons, polycyclic aromatic hydrocarbons (PAHs), polychlorodibenzo-p-dioxin, polychlorodibenzofurans (PCDD/Fs), and dioxin-like PCBs are shown. Regarding semivolatile compounds, phenol, styrene, and its derivatives had the highest yields. In nearly all the runs the same PAHs were identified, naphthalene being the most common component obtained. Combustion of the printed circuit board produced the highest emission factor of PCDD/Fs, possibly due to the high copper content.

  14. Discursive Deployments: Mobilizing Support for Municipal and Community Wireless Networks in the U.S.

    SciTech Connect (OSTI)

    Alvarez, Rosio; Rodriguez, Juana Maria

    2008-08-16

    This paper examines Municipal Wireless (MW) deployments in the United States. In particular, the interest is in understanding how discourse has worked to mobilize widespread support for MW networks. We explore how local governments discursively deploy the language of social movements to create a shared understanding of the networking needs of communities. Through the process of"framing" local governments assign meaning to the MW networks in ways intended to mobilize support anddemobilize opposition. The mobilizing potential of a frame varies and is dependent on its centrality and cultural resonance. We examine the framing efforts of MW networks by using a sample of Request for Proposals for community wireless networks, semi-structured interviews and local media sources. Prominent values that are central to a majority of the projects and others that are culturally specific are identified and analyzed for their mobilizing potency.

  15. The mobility of uranium and associated trace elements in the Bates Mountain Tuff, central Nevada

    SciTech Connect (OSTI)

    Kizis, J.A.; Runnells, D.D.

    1984-05-01

    Several investigators have documented the mobility of uranium in silicic volcanics and postulated that such mobilization could lead to the formation of U ore deposits (Shatkov et al., 1970; Rosholt et al., 1971; Zielinski and Rosholt, 1978; Zielinski, 1978; Henry and Tyner, 1978; Stuart et al., 1983). The mobility of U in the Bates Mountain Tuff is examined in this study because the Bates Mountain Tuff is chemically similar to the numerous, major ash-flow sheets that are exposed in the Great Basin and is a potential source rock for U. The mobility of Li, Mo, and F are examined in this study because these elements are commonly enriched in U deposits associated with volcanic rocks. In contrast, Th was studied because it is probably immobile during glass hydration, devitrification, and alteration to clay and may therefore serve as an index of the primary magmatic homogeneity of each cooling unit.

  16. MODELING OF LONG-TERM FATE OF MOBILIZED FINES DUE TO DAM-EMBANKMENT...

    Office of Scientific and Technical Information (OSTI)

    Conference: MODELING OF LONG-TERM FATE OF MOBILIZED FINES DUE TO DAM-EMBANKMENT INTERFACIAL DISLOCATIONS Citation Details In-Document Search Title: MODELING OF LONG-TERM FATE OF ...

  17. Fuel Savings and Emission Reductions from Next-Generation Mobile Air Conditioning Technology in India: Preprint

    SciTech Connect (OSTI)

    Chaney, L.; Thundiyil, K.; Chidambaram, S.; Abbi, Y. P.; Anderson, S.

    2007-05-01

    This paper quantifies the mobile air-conditioning fuel consumption of the typical Indian vehicle, exploring potential fuel savings and emissions reductions these systems for the next generation of vehicles.

  18. High-mobility BaSnO{sub 3} grown by oxide molecular beam epitaxy

    SciTech Connect (OSTI)

    Raghavan, Santosh; Schumann, Timo; Kim, Honggyu; Zhang, Jack Y.; Cain, Tyler A.; Stemmer, Susanne

    2016-01-01

    High-mobility perovskite BaSnO{sub 3} films are of significant interest as new wide bandgap semiconductors for power electronics, transparent conductors, and as high mobility channels for epitaxial integration with functional perovskites. Despite promising results for single crystals, high-mobility BaSnO{sub 3} films have been challenging to grow. Here, we demonstrate a modified oxide molecular beam epitaxy (MBE) approach, which supplies pre-oxidized SnO{sub x}. This technique addresses issues in the MBE of ternary stannates related to volatile SnO formation and enables growth of epitaxial, stoichiometric BaSnO{sub 3}. We demonstrate room temperature electron mobilities of 150 cm{sup 2} V{sup −1} s{sup −1} in films grown on PrScO{sub 3}. The results open up a wide range of opportunities for future electronic devices.

  19. Surfactant Based Enhanced Oil Recovery and Foam Mobility Control

    SciTech Connect (OSTI)

    George J. Hirasaki; Clarence A. Miller; Gary A. Pope

    2005-07-01

    Surfactant flooding has the potential to significantly increase recovery over that of conventional waterflooding. The availability of a large number of surfactant structures makes it possible to conduct a systematic study of the relation between surfactant structure and its efficacy for oil recovery. A combination of two surfactants was found to be particularly effective for application in carbonate formations at low temperature. A formulation has been designed for a particular field application. The addition of an alkali such as sodium carbonate makes possible in situ generation of surfactant and significant reduction of surfactant adsorption. In addition to reduction of interfacial tension to ultra-low values, surfactants and alkali can be designed to alter wettability to enhance oil recovery. The design of the process to maximize the region of ultra-low IFT is more challenging since the ratio of soap to synthetic surfactant is a parameter in the conditions for optimal salinity. Compositional simulation of the displacement process demonstrates the interdependence of the various components for oil recovery. An alkaline surfactant process is designed to enhance spontaneous imbibition in fractured, oil-wet, carbonate formations. It is able to recover oil from dolomite core samples from which there was no oil recovery when placed in formation brine. Mobility control is essential for surfactant EOR. Foam is evaluated to improve the sweep efficiency of surfactant injected into fractured reservoirs. UTCHEM is a reservoir simulator specially designed for surfactant EOR. It has been modified to represent the effects of a change in wettability. Simulated case studies demonstrate the effects of wettability.

  20. Results of mobile gamma scanning activities in St. Louis, Missouri

    SciTech Connect (OSTI)

    Rodriguez, R E; Witt, D A; Cottrell, W D; Carrier, R F

    1991-06-01

    From 1942 through approximately 1966, the Mallinckrodt Chemical Works operated four plants in St. Louis, Missouri, for the Manhattan Engineer District and the Atomic Energy Commission. A variety of production processes using uranium- and radium-bearing ore materials were performed at the plants. It is the policy of the DOE to verify that radiological conditions at such sites or facilities comply with current DOE guidelines. Guidelines for release and use of such sites have become more stringent as research has provided more information since previous cleanups. The Formerly Utilized Sites Remedial Action Program (FUSRAP) was established as part of that effort to confirm the closeout status of facilities under contract to agencies preceding DOE during early nuclear energy development. Under the FUSRAP program, the Mallinckrodt properties have been previously investigated to determine the extent of on-site radiological contamination. At the request of DOE, Oak Ridge National Laboratory (ORNL) conducted a survey in May 1990, of public roadways and suspected haul routes between the Mallinckrodt plant and storage sites in St. Louis to ensure that no residual radioactive materials were conveyed off-site. A mobile gamma scanning van with an on-board computer system was used to identify possible anomalies. Suspect areas are those displaying measurements deviating from gamma exposure rates identified as typical for radiologically unenhanced areas in the vicinity of the areas of interest. The instrumentation highlighted three anomaly locations each of which measured less than 1m{sup 2} in size. None of the slightly elevated radiation levels originated from material associated with former AEC-related processing operations in the area. The anomalies resulted from elevated concentrations of radionuclides present in phosphate fertilizers, increased thorium in road-base gravel, and emanations from the radioactive storage site near the Latty Avenue airport. 9 refs., 3 figs.

  1. Eliminating Medical Waste Liabilities Through Mobile Maceration and Disinfection

    SciTech Connect (OSTI)

    R. A. Rankin; N. R. Soelberg; K. M. Klingler; C. W. Lagle; L. L. Byers

    2006-02-01

    Commercial medical waste treatment technologies include incineration, melting, autoclaving, and chemical disinfection. Incineration disinfects, destroys the original nature of medical waste, and reduces the waste volume by converting organic waste content to carbon dioxide and water, leaving only residual inorganic ash. However, medical waste incinerator numbers have plummeted from almost 2,400 in 1995 to 115 in 2003 and to about 62 in 2005, due to negative public perception and escalating compliance costs associated with increasingly strict regulations. High-temperature electric melters have been designed and marketed as incinerator alternatives, but they are also costly and generally must comply with the same incinerator emissions regulations and permitting requirements. Autoclave processes disinfect medical waste at much lower operating temperatures than incinerators operate at, but are sometimes subject to limitations such as waste segregration requirements to be effective. Med-Shred, Inc. has developed a patented mobile shredding and chemical disinfecting process for on-site medical waste treatment. Medical waste is treated on-site at customer facilities by shredding and disinfecting the waste. The treated waste can then be transported in compliance with Health Insurance Portability and Accountability Act of 1996 (HIPAA) requirements to a landfill for disposal as solid municipal waste. A team of Idaho National Laboratory engineers evaluated the treatment process design. The process effectiveness has been demonstrated in mycobacterium tests performed by Analytical Services Incorporated. A process description and the technical and performance evaluation results are presented in the paper. A treatment demonstration and microbiological disinfecting tests show that the processor functions as it was intended.

  2. Cooperative system and method using mobile robots for testing a cooperative search controller

    DOE Patents [OSTI]

    Byrne, Raymond H.; Harrington, John J.; Eskridge, Steven E.; Hurtado, John E.

    2002-01-01

    A test system for testing a controller provides a way to use large numbers of miniature mobile robots to test a cooperative search controller in a test area, where each mobile robot has a sensor, a communication device, a processor, and a memory. A method of using a test system provides a way for testing a cooperative search controller using multiple robots sharing information and communicating over a communication network.

  3. SCR & DPF RETROFITS FOR MOBILE DIESEL ENGINES | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    & DPF RETROFITS FOR MOBILE DIESEL ENGINES SCR & DPF RETROFITS FOR MOBILE DIESEL ENGINES 2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations and Posters 2005_deer_leprince.pdf (290.81 KB) More Documents & Publications Development of ADECS to Meet 2010 Emission Levels: Optimization of NOx, NH3 and Fuel Consumption Using High and Low Engine-Out NOx Calibrations Low Emissions Potential of EGR-SCR-DPF and Advanced Fuel Formulation - A Progress Report The Development and

  4. Measuring "Real World" Heavy-Duty Diesel Emissions with a Mobile Lab |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy "Real World" Heavy-Duty Diesel Emissions with a Mobile Lab Measuring "Real World" Heavy-Duty Diesel Emissions with a Mobile Lab 2002 DEER Conference Presentation: University of California, Riverside 2002_deer_miller.pdf (1.13 MB) More Documents & Publications The California Demonstration Program for Control of PM from Diesel Backup Generators (BUGs) The California Demonstration Program for Control of PM from Diesel Backup Generators = Recent

  5. AlSb/InAs HIGH ELECTRON MOBILITY TRANSISTORS - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electricity Transmission Electricity Transmission Advanced Materials Advanced Materials Find More Like This Return to Search AlSb/InAs HIGH ELECTRON MOBILITY TRANSISTORS Naval Research Laboratory Contact NRL About This Technology Technology Marketing Summary The Naval Research Laboratory (NRL) has developed materials growth and fabrication technology for the manufacture of high-speed, low power AlSb/InAs high electron mobility transistors (HEMTs) that exhibit state-of-the-art low-power

  6. Mobile source emission control cost-effectiveness: Issues, uncertainties, and results

    SciTech Connect (OSTI)

    Wang, M.Q.

    1994-12-01

    Emissions from mobile sources undoubtedly contribute to US urban air pollution problems. Consequently, mobile source control measures, ranging from vehicle emission standards to reducing vehicle travel, have been adopted or proposed to help attain air quality standards. To rank various mobile source control measures, various government agencies and private organizations calculate cost-effectiveness in dollars per ton of emissions reduced. Arguments for or against certain control measures are often made on the basis of the calculated cost-effectiveness. Yet, different studies may yield significantly different cost-effectiveness results, because of the various methodologies used and assumptions regarding the values of costs and emission reductions. Because of the methodological differences, the cost-effectiveness results may not be comparable between studies. Use of incomparable cost-effectiveness results may result in adoption of ineffective control measures. This paper first discusses some important methodological issues involved in cost-effectiveness calculation for mobile sources and proposes appropriate, systematic methods for dealing with these issues. Various studies have been completed recently to evaluate the cost-effectiveness of mobile source emission control measures. These studies resulted in wide variations in the cost-effectiveness for same control measures. Methodological assumptions used in each study are presented and, based on the proposed methods for cost-effectiveness calculation, adjustments are applied to the original estimates in each study to correct inappropriate methodological assumptions and to make the studies comparable. Finally, mobile source control measures are ranked on the basis of the adjusted cost-effectiveness estimates.

  7. Measurement of the differential pressure of liquid metals

    DOE Patents [OSTI]

    Metz, H.J.

    1975-09-01

    This patent relates to an improved means for measuring the differential pressure between any two points in a process liquid metal coolant loop, wherein the flow of liquid metal in a pipe is opposed by a permanent magnet liquid metal pump until there is almost zero flow shown by a magnetic type flowmeter. The pressure producing the liquid metal flow is inferred from the rate of rotation of the permanent magnet pump. In an alternate embodiment, a differential pressure transducer is coupled to a process pipeline by means of high-temperature bellows or diaphragm seals, and a permanent magnet liquid metal pump in the high-pressure transmission line to the pressure transducer can be utilized either for calibration of the transducer or for determining the process differential pressure as a function of the magnet pump speed. (auth)

  8. An Adaptive Unified Differential Evolution Algorithm for Global Optimization

    SciTech Connect (OSTI)

    Qiang, Ji; Mitchell, Chad

    2014-11-03

    In this paper, we propose a new adaptive unified differential evolution algorithm for single-objective global optimization. Instead of the multiple mutation strate- gies proposed in conventional differential evolution algorithms, this algorithm employs a single equation unifying multiple strategies into one expression. It has the virtue of mathematical simplicity and also provides users the flexibility for broader exploration of the space of mutation operators. By making all control parameters in the proposed algorithm self-adaptively evolve during the process of optimization, it frees the application users from the burden of choosing appro- priate control parameters and also improves the performance of the algorithm. In numerical tests using thirteen basic unimodal and multimodal functions, the proposed adaptive unified algorithm shows promising performance in compari- son to several conventional differential evolution algorithms.

  9. MOBILE4. 1: Highway-vehicle mobile-source emission-factor model (Apple MacIntosh version) (for microcomputers). Model-Simulation

    SciTech Connect (OSTI)

    Not Available

    1991-08-01

    MOBILE4.1 is the latest revision to EPA's highway vehicle mobile source emission factor model. Relative to MOBILE4, it contains numerous revisions and provides the user with additional options for modeling highway vehicle emission factors. it will calculate emission factors for hydrocarbons (HC), carbon monoxide, (CO), and oxides of nitrogen (NOx) from highway motor vehicles. It calculates emission factors for eight individual vehicle types, in two regions of the country (low and high altitude). The emission factors depend on various conditions such as ambient temperature, fuel volatility, speed, and mileage accrual rates. It will estimate emission factors for any calendar year between 1960 and 2020 inclusive. The 25 most recent model years are considered in operation in each calendar year. EPA is requiring that states and others preparing emission inventories for nonattainment areas for CO and ozone to use MOBILE4.1 in the development of the base year 1990 emission inventories required under the Clean Air Act of 1990.

  10. D-Cycle - 4-Differential -Stroke Cycle | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    D-Cycle - 4-Differential -Stroke Cycle D-Cycle - 4-Differential -Stroke Cycle The D-Cycle offers the opportunity to use less fuel and gain more power while being able to be retrofit to an OEM and aftermarket engines deer09_conti.pdf (104.32 KB) More Documents & Publications Improving Diesel Engine Sweet-spot Efficiency and Adapting it to Improve Duty-cycle MPG - plus Increasing Propulsion and Reducing Cost Two-Stroke Engines: New Frontier in Engine Efficiency Building America Technology

  11. MOBILIZATION AND CHARACTERIZATION OF COLLOIDS GENERATED FROM CEMENT LEACHATES MOVING THROUGH A SRS SANDY SEDIMENT

    SciTech Connect (OSTI)

    Li, D.; Roberts, K.; Kaplan, D.; Seaman, J.

    2011-09-20

    Naturally occurring mobile colloids are ubiquitous and are involved in many important processes in the subsurface zone. For example, colloid generation and subsequent mobilization represent a possible mechanism for the transport of contaminants including radionuclides in the subsurface environments. For colloid-facilitated transport to be significant, three criteria must be met: (1) colloids must be generated; (2) contaminants must associate with the colloids preferentially to the immobile solid phase (aquifer); and (3) colloids must be transported through the groundwater or in subsurface environments - once these colloids start moving they become 'mobile colloids'. Although some experimental investigations of particle release in natural porous media have been conducted, the detailed mechanisms of release and re-deposition of colloidal particles within natural porous media are poorly understood. Even though this vector of transport is known, the extent of its importance is not known yet. Colloid-facilitated transport of trace radionuclides has been observed in the field, thus demonstrating a possible radiological risk associated with the colloids. The objective of this study was to determine if cementitious leachate would promote the in situ mobilization of natural colloidal particles from a SRS sandy sediment. The intent was to determine whether cementitious surface or subsurface structure would create plumes that could produce conditions conducive to sediment dispersion and mobile colloid generation. Column studies were conducted and the cation chemistries of influents and effluents were analyzed by ICP-OES, while the mobilized colloids were characterized using XRD, SEM, EDX, PSD and Zeta potential. The mobilization mechanisms of colloids in a SRS sandy sediment by cement leachates were studied.

  12. Sulfide-Driven Arsenic Mobilization from Arsenopyrite and Black Shale Pyrite

    SciTech Connect (OSTI)

    Zhu, W.; Young, L; Yee, N; Serfes, M; Rhine, E; Reinfelder, J

    2008-01-01

    We examined the hypothesis that sulfide drives arsenic mobilization from pyritic black shale by a sulfide-arsenide exchange and oxidation reaction in which sulfide replaces arsenic in arsenopyrite forming pyrite, and arsenide (As-1) is concurrently oxidized to soluble arsenite (As+3). This hypothesis was tested in a series of sulfide-arsenide exchange experiments with arsenopyrite (FeAsS), homogenized black shale from the Newark Basin (Lockatong formation), and pyrite isolated from Newark Basin black shale incubated under oxic (21% O2), hypoxic (2% O2, 98% N2), and anoxic (5% H2, 95% N2) conditions. The oxidation state of arsenic in Newark Basin black shale pyrite was determined using X-ray absorption-near edge structure spectroscopy (XANES). Incubation results show that sulfide (1 mM initial concentration) increases arsenic mobilization to the dissolved phase from all three solids under oxic and hypoxic, but not anoxic conditions. Indeed under oxic and hypoxic conditions, the presence of sulfide resulted in the mobilization in 48 h of 13-16 times more arsenic from arsenopyrite and 6-11 times more arsenic from isolated black shale pyrite than in sulfide-free controls. XANES results show that arsenic in Newark Basin black shale pyrite has the same oxidation state as that in FeAsS (-1) and thus extend the sulfide-arsenide exchange mechanism of arsenic mobilization to sedimentary rock, black shale pyrite. Biologically active incubations of whole black shale and its resident microorganisms under sulfate reducing conditions resulted in sevenfold higher mobilization of soluble arsenic than sterile controls. Taken together, our results indicate that sulfide-driven arsenic mobilization would be most important under conditions of redox disequilibrium, such as when sulfate-reducing bacteria release sulfide into oxic groundwater, and that microbial sulfide production is expected to enhance arsenic mobilization in sedimentary rock aquifers with major pyrite-bearing, black

  13. Differential phase contrast X-ray imaging system and components

    DOE Patents [OSTI]

    Stutman, Daniel; Finkenthal, Michael

    2014-07-01

    A differential phase contrast X-ray imaging system includes an X-ray illumination system, a beam splitter arranged in an optical path of the X-ray illumination system, and a detection system arranged in an optical path to detect X-rays after passing through the beam splitter.

  14. Manifold gasket accommodating differential movement of fuel cell stack

    SciTech Connect (OSTI)

    Kelley, Dana A.; Farooque, Mohammad

    2007-11-13

    A gasket for use in a fuel cell system having at least one externally manifolded fuel cell stack, for sealing the manifold edge and the stack face. In accordance with the present invention, the gasket accommodates differential movement between the stack and manifold by promoting slippage at interfaces between the gasket and the dielectric and between the gasket and the stack face.

  15. The relationship between grain boundary structure, defect mobility, and grain boundary sink efficiency

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Uberuaga, Blas Pedro; Vernon, Louis J.; Martinez, Enrique; Voter, Arthur F.

    2015-03-13

    Nanocrystalline materials have received great attention due to their potential for improved functionality and have been proposed for extreme environments where the interfaces are expected to promote radiation tolerance. However, the precise role of the interfaces in modifying defect behavior is unclear. Using long-time simulations methods, we determine the mobility of defects and defect clusters at grain boundaries in Cu. We find that mobilities vary significantly with boundary structure and cluster size, with larger clusters exhibiting reduced mobility, and that interface sink efficiency depends on the kinetics of defects within the interface via the in-boundary annihilation rate of defects. Thus,more » sink efficiency is a strong function of defect mobility, which depends on boundary structure, a property that evolves with time. Further, defect mobility at boundaries can be slower than in the bulk, which has general implications for the properties of polycrystalline materials. Finally, we correlate defect energetics with the volumes of atomic sites at the boundary.« less

  16. Transportation Electrification Education Partnership for Green Jobs and Sustainable Mobility

    SciTech Connect (OSTI)

    Peng, Huei; Mi, Chris; Gover, James

    2013-06-28

    This collaborative educational project between the University of Michigan—Ann Arbor, University of Michigan—Dearborn and the Kettering University successfully executed almost all the elements we proposed to do. In the original proposal, we proposed to develop four graduate courses, six undergraduate courses, four professional short courses, a K-12 electric vehicle education kit, a Saturday morning seminar series, and a set of consumer education material to support the advancement of transportation electrification. The first four deliverables were all successfully developed and offered. When we held the kick-off meeting in NETL in Morgantown back in early 2010 with all the ten ARRA education teams, however, it quickly became clear that among the ten ARRA education grantee teams, our proposed “consume education” activities are not better or with the potential to create bigger impact than some of activities proposed in other teams. For example, the Odyssey 2010 event held by the West Virginia University team had planned and successfully reached to more than 230,000 attendees, which is way more than what our proposed 100k event could ever reach. It was under the suggestion of Joseph Quaranta, the ARRA education Program Director at that time, that we should coordinate and eliminate redundancy. The resources should then be focused on activities that have less overlap. Therefore, the originally proposed activities: Saturday morning seminar series, and a set of consumer education material were dropped from our scope. We expanded the scope of our “education kit” activity to include some educational materials, mainly in the form of videos. The target audience also changed from general public to K-12 students. The majority of the project cost (~70%) goes toward the establishment of three undergraduate laboratories, which provides critically needed hands-on learning experience for next-generation green mobility engineers. We are very proud that the ARRA money

  17. T-670: Skype Input Validation Flaw in 'mobile phone' Profile Entry Permits Cross-Site Scripting Attacks

    Broader source: Energy.gov [DOE]

    The software does not properly filter HTML code from user-supplied input in the The "mobile phone" profile entry before displaying the input.

  18. PNNI routing support for ad hoc mobile networking: A flat architecture

    SciTech Connect (OSTI)

    Martinez, L.; Sholander, P.; Tolendino, L.

    1997-12-01

    This contribution extends the Outside Nodal Hierarchy List (ONHL) procedures described in ATM Form Contribution 97-0766. These extensions allow multiple mobile networks to form either an ad hoc network or an extension of a fixed PNNI infrastructure. This contribution covers the simplest case where the top-most Logical Group Nodes (LGNs), in those mobile networks, all reside at the same level in a PNNI hierarchy. Future contributions will cover the general case where those top-most LGNs reside at different hierarchy levels. This contribution considers a flat ad hoc network architecture--in the sense that each mobile network always participates in the PNNI hierarchy at the preconfigured level of its top-most LGN.

  19. Method for tracking the location of mobile agents using stand-off detection technique

    DOE Patents [OSTI]

    Schmitt, Randal L.; Bender, Susan Fae Ann; Rodacy, Philip J.; Hargis, Jr., Philip J.; Johnson, Mark S.

    2006-12-26

    A method for tracking the movement and position of mobile agents using light detection and ranging (LIDAR) as a stand-off optical detection technique. The positions of the agents are tracked by analyzing the time-history of a series of optical measurements made over the field of view of the optical system. This provides a (time+3-D) or (time+2-D) mapping of the location of the mobile agents. Repeated pulses of a laser beam impinge on a mobile agent, such as a bee, and are backscattered from the agent into a LIDAR detection system. Alternatively, the incident laser pulses excite fluorescence or phosphorescence from the agent, which is detected using a LIDAR system. Analysis of the spatial location of signals from the agents produced by repeated pulses generates a multidimensional map of agent location.

  20. Feasibility Study of Implementing a Mobile Collaborative Information Platform for International Safeguards Inspections

    SciTech Connect (OSTI)

    Gastelum, Zoe N.; Gitau, Ernest TN; Doehle, Joel R.; Toomey, Christopher M.

    2014-09-30

    In response to the growing pervasiveness of mobile technologies such as tablets and smartphones, the International Atomic Energy Agency and the U.S. Department of Energy National Laboratories have been exploring the potential use of these platforms for international safeguards activities. Specifically of interest are information systems (software, and accompanying servers and architecture) deployed on mobile devices to increase the situational awareness and productivity of an IAEA safeguards inspector in the field, while simultaneously reducing paperwork and pack weight of safeguards equipment. Exploratory development in this area has been met with skepticism regarding the ability to overcome technology deployment challenges for IAEA safeguards equipment. This report documents research conducted to identify potential challenges for the deployment of a mobile collaborative information system to the IAEA, and proposes strategies to mitigate those challenges.

  1. A mobile-agent based wireless sensing network for structural monitoring applications

    SciTech Connect (OSTI)

    Taylor, Stuart G; Farinholt, Kevin M; Figueiredo, Eloi; Park, Gyuhae; Farrar, Charles R; Flynn, Eric B; Mascarenas, David L; Todd, Michael D

    2008-01-01

    A new wireless sensing network paradigm is presented for structural monitoring applications. In this approach, both power and data interrogation commands are conveyed via a mobile agent that is sent to sensor nodes to perform intended interrogations, which can alleviate several limitations of the traditional sensing networks. Furthermore, the mobile agent provides computational power to make near real-time assessments on the structural conditions. This paper will discuss such prototype systems, which are used to interrogate impedance-based sensors for structural health monitoring applications. Our wireless sensor node is specifically designed to accept various energy sources, including wireless energy transmission, and to be wirelessly triggered on an as-needed basis by the mobile agent or other sensor nodes. The capabilities of this proposed sensing network paradigm are demonstrated in the laboratory and the field.

  2. Determination of carrier lifetime and mobility in colloidal quantum dot films via impedance spectroscopy

    SciTech Connect (OSTI)

    Rath, Arup K.; Lasanta, Tania; Bernechea, Maria; Diedenhofen, Silke L.; Konstantatos, Gerasimos

    2014-02-10

    Impedance Spectroscopy (IS) proves to be a powerful tool for the determination of carrier lifetime and majority carrier mobility in colloidal quantum dot films. We employ IS to determine the carrier lifetime in PbS quantum dot Schottky solar cells with Al and we verify the validity of the technique via transient photovoltage. We also present a simple approach based on an RC model that allows the determination of carrier mobility in PbS quantum dot films and we corroborate the results via comparison with space charge limited measurements. In summary, we demonstrate the potential of IS to characterize key-to-photovoltaics optoelectronic properties, carrier lifetime, and mobility, in a facile way.

  3. Tuning carrier mobility without spin transport degrading in copper-phthalocyanine

    SciTech Connect (OSTI)

    Jiang, S. W.; Wang, P.; Chen, B. B.; Zhou, Y.; Ding, H. F. E-mail: dwu@nju.edu.cn; Wu, D. E-mail: dwu@nju.edu.cn

    2015-07-27

    We demonstrate more than one order of magnitude of carrier mobility tuning for the copper-phthalocyanine (CuPc) without spin transport degrading in organic spin valve devices. Depending on the preparation conditions, organic spin valves with the CuPc film mobility of 5.78 × 10{sup −3} and 1.11 × 10{sup −4} cm{sup 2}/V s are obtained for polycrystalline and amorphous CuPc, respectively. Strikingly, the spin diffusion lengths are almost the same regardless of their mobilities that are ∼50 times different, which is in sharp contrast with previous prediction. These findings directly support that the spin relaxation in CuPc is dominated by the spin-orbit coupling.

  4. Influence of interface mobility on the evolution of Austenite-Martensite grain assemblies during annealing

    SciTech Connect (OSTI)

    Clarke, Amy J; Santofimia, Maria J; Speer, John G; Zhao, L; Sietsma, Jilt

    2009-01-01

    The quenching and partitioning (Q&P) process is a new heat treatment for the creation of advanced high-strength steels. This treatment consists of an initial partial or full austenitization, followed by a quench to form a controlled amount of martensite and an annealing step to partition carbon atoms from the martensite to the austenite. In this work, the microstructural evolution during annealing of martensite-austenite grain assemblies has been analyzed by means of a modeling approach that considers the influence of martensite-austenite interface migration on the kinetics of carbon partitioning. Carbide precipitation is precluded in the model, and three different assumptions about interface mobility are considered, ranging from a completely immobile interface to the relatively high mobility of an incoherent ferrite-austenite interface. Simulations indicate that different interface mobilities lead to profound differences in the evolution of microstructure that is predicted during annealing.

  5. Enhancing Biological Analyses with Three Dimensional Field Asymmetric Ion Mobility, Low Field Drift Time Ion Mobility and Mass Spectrometry (FAIMS/IMS-MS) Separations

    SciTech Connect (OSTI)

    Zhang, Xing; Ibrahim, Yehia M.; Chen, Tsung-Chi; Kyle, Jennifer E.; Norheim, Randolph V.; Monroe, Matthew E.; Smith, Richard D.; Baker, Erin Shammel

    2015-06-30

    We report the first evaluation of a platform coupling a high speed field asymmetric ion mobility spectrometry microchip (FAIMS) with drift tube ion mobility and mass spectrometry (IMS-MS). The FAIMS/IMS-MS platform was used to analyze biological samples and simultaneously acquire multidimensional information of detected features from the measured FAIMS compensation fields and IMS drift times, while also obtaining accurate ion masses. These separations thereby increase the overall separation power, resulting increased information content, and provide more complete characterization of more complex samples. The separation conditions were optimized for sensitivity and resolving power by the selection of gas compositions and pressures in the FAIMS and IMS separation stages. The resulting performance provided three dimensional separations, benefitting both broad complex mixture studies and targeted analyses by e.g. improving isomeric separations and allowing detection of species obscured by chemical noise and other interfering peaks.

  6. Mobilization and Transport of Organic Compounds from Reservoir Rock and Caprock in Geological Carbon Sequestration Sites

    SciTech Connect (OSTI)

    Zhong, Lirong; Cantrell, Kirk J.; Mitroshkov, Alexandre V.; Shewell, Jesse L.

    2014-05-06

    Supercritical CO2 (scCO2) is an excellent solvent for organic compounds, including benzene, toluene, ethyl-benzene, and xylene (BTEX), phenols, and polycyclic aromatic hydrocarbons (PAHs). Monitoring results from geological carbon sequestration (GCS) field tests has shown that organic compounds are mobilized following CO2 injection. Such results have raised concerns regarding the potential for groundwater contamination by toxic organic compounds mobilized during GCS. Knowledge of the mobilization mechanism of organic compounds and their transport and fate in the subsurface is essential for assessing risks associated with GCS. Extraction tests using scCO2 and methylene chloride (CH2Cl2) were conducted to study the mobilization of volatile organic compounds (VOCs, including BTEX), the PAH naphthalene, and n-alkanes (n-C20 – n-C30) by scCO2 from representative reservoir rock and caprock obtained from depleted oil reservoirs and coal from an enhanced coal-bed methane recovery site. More VOCs and naphthalene were extractable by scCO2 compared to the CH2Cl2 extractions, while scCO2 extractable alkane concentrations were much lower than concentrations extractable by CH2Cl2. In addition, dry scCO2 was found to extract more VOCs than water saturated scCO2, but water saturated scCO2 mobilized more naphthalene than dry scCO2. In sand column experiments, moisture content was found to have an important influence on the transport of the organic compounds. In dry sand columns the majority of the compounds were retained in the column except benzene and toluene. In wet sand columns the mobility of the BTEX was much higher than that of naphthalene. Based upon results determined for the reservoir rock, caprock, and coal samples studied here, the risk to aquifers from contamination by organic compounds appears to be relatively low; however, further work is necessary to fully evaluate risks from depleted oil reservoirs.

  7. Measuring charge carrier mobility in photovoltaic devices with micron-scale resolution

    SciTech Connect (OSTI)

    Ashraf, A.; Dissanayake, D. M. N. M.; Eisaman, M. D.

    2015-03-16

    We present a charge-extraction technique, micron-scale charge extraction by linearly increasing voltage, which enables simultaneous spatially resolved measurements of charge carrier mobility and photocurrent in thin-film photovoltaic devices with micron-scale resolution. An intensity-modulated laser with beam diameter near the optical diffraction limit is scanned over the device, while a linear voltage ramp in reverse bias is applied at each position of illumination. We calculate the majority carrier mobility, photocurrent, and number of photogenerated charge carriers from the resulting current transient. We demonstrate this technique on an organic photovoltaic device, but it is applicable to a wide range of photovoltaic materials.

  8. Mobile computing device configured to compute irradiance, glint, and glare of the sun

    DOE Patents [OSTI]

    Gupta, Vipin P; Ho, Clifford K; Khalsa, Siri Sahib

    2014-03-11

    Described herein are technologies pertaining to computing the solar irradiance distribution on a surface of a receiver in a concentrating solar power system or glint/glare emitted from a reflective entity. A mobile computing device includes at least one camera that captures images of the Sun and the entity of interest, wherein the images have pluralities of pixels having respective pluralities of intensity values. Based upon the intensity values of the pixels in the respective images, the solar irradiance distribution on the surface of the entity or glint/glare corresponding to the entity is computed by the mobile computing device.

  9. Hole mobility enhancement of MEH-PPV film by heat treatment at T{sub g}

    SciTech Connect (OSTI)

    Kajiya, Daisuke; Koganezawa, Tomoyuki; Saitow, Ken-ichi

    2015-12-15

    The hole mobility of poly[2-methoxy-5-(2′-ethylhexyloxy)-1,4-phenylene vinylene] (MEH-PPV) film was measured using the time-of-flight method. The hole mobility was enhanced 4-fold after annealing at around the glass transition temperature (T{sub g}). Optical, atomic force, and Kelvin force microscopies, and grazing-incidence X-ray diffraction measurements indicate the enhancement can be attributed to a homogeneous film structure, a homogeneous Fermi level energy, and a face-on oriented structure, all of which were established by annealing at T{sub g}.

  10. "Lantern Live" Mobile App Lights Way for Citizens Impacted by Disasters |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy "Lantern Live" Mobile App Lights Way for Citizens Impacted by Disasters "Lantern Live" Mobile App Lights Way for Citizens Impacted by Disasters November 24, 2014 - 5:06pm Addthis (Editor's Note: the following was originally posted on the White House Office of Science and Technology Policy blog on November 21, 2014.) By Brian Forde, Denice Ross and Derek Frempong In the wake of Hurricane Sandy, seemingly simple tasks such as refueling your car were

  11. DOE Awards Contract for WIPP Mobile Loading Unit Services | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy WIPP Mobile Loading Unit Services DOE Awards Contract for WIPP Mobile Loading Unit Services August 27, 2012 - 12:00pm Addthis Media Contacts Bill Taylor Bill.Taylor@srs.gov 803-952-8564 Deb Gill Deb.Gill@wipp.ws 575-234-7270 Cincinnati - The U.S. Department of Energy (DOE) today awarded a competitive small business contract to Celeritex, LLC, (a Joint Venture between Project Services Group, LLC and DeNuke Contracting Services Inc.) of Suwanee, Georgia. The contract is to provide

  12. Controlled differential pressure system for an enhanced fluid blending apparatus

    SciTech Connect (OSTI)

    Hallman, Jr., Russell Louis

    2009-02-24

    A system and method for producing a controlled blend of two or more fluids. Thermally-induced permeation through a permeable tube is used to mix a first fluid from outside the tube with a second fluid flowing through the tube. Mixture ratios may be controlled by adjusting the temperature of the first fluid or by adjusting the pressure drop through the permeable tube. The combination of a back pressure control valve and a differential regulator is used to control the output pressure of the blended fluid. The combination of the back pressure control valve and differential regulator provides superior flow control of the second dry gas. A valve manifold system may be used to mix multiple fluids, and to adjust the volume of blended fluid produced, and to further modify the mixture ratio.

  13. Local random potentials of high differentiability to model the Landscape

    SciTech Connect (OSTI)

    Battefeld, T.; Modi, C.

    2015-03-09

    We generate random functions locally via a novel generalization of Dyson Brownian motion, such that the functions are in a desired differentiability class C{sup k}, while ensuring that the Hessian is a member of the Gaussian orthogonal ensemble (other ensembles might be chosen if desired). Potentials in such higher differentiability classes (k≥2) are required/desirable to model string theoretical landscapes, for instance to compute cosmological perturbations (e.g., k=2 for the power-spectrum) or to search for minima (e.g., suitable de Sitter vacua for our universe). Since potentials are created locally, numerical studies become feasible even if the dimension of field space is large (D∼100). In addition to the theoretical prescription, we provide some numerical examples to highlight properties of such potentials; concrete cosmological applications will be discussed in companion publications.

  14. Adaptive array technique for differential-phase reflectometry in QUEST

    SciTech Connect (OSTI)

    Idei, H. Hanada, K.; Zushi, H.; Nagata, K.; Mishra, K.; Itado, T.; Akimoto, R.; Yamamoto, M. K.

    2014-11-15

    A Phased Array Antenna (PAA) was considered as launching and receiving antennae in reflectometry to attain good directivity in its applied microwave range. A well-focused beam was obtained in a launching antenna application, and differential-phase evolution was properly measured by using a metal reflector plate in the proof-of-principle experiment at low power test facilities. Differential-phase evolution was also evaluated by using the PAA in the Q-shu University Experiment with Steady State Spherical Tokamak (QUEST). A beam-forming technique was applied in receiving phased-array antenna measurements. In the QUEST device that should be considered as a large oversized cavity, standing wave effect was significantly observed with perturbed phase evolution. A new approach using derivative of measured field on propagating wavenumber was proposed to eliminate the standing wave effect.

  15. Numerical solution of three-dimensional magnetic differential equations

    SciTech Connect (OSTI)

    Reiman, A.H.; Greenside, H.S.

    1987-02-01

    A computer code is described that solves differential equations of the form B . del f = h for a single-valued solution f, given a toroidal three-dimensional divergence-free field B and a single-valued function h. The code uses a new algorithm that Fourier decomposes a given function in a set of flux coordinates in which the field lines are straight. The algorithm automatically adjusts the required integration lengths to compensate for proximity to low order rational surfaces. Applying this algorithm to the Cartesian coordinates defines a transformation to magnetic coordinates, in which the magnetic differential equation can be accurately solved. Our method is illustrated by calculating the Pfirsch-Schlueter currents for a stellarator.

  16. System for measuring multiphase flow using multiple pressure differentials

    DOE Patents [OSTI]

    Fincke, James R.

    2003-01-01

    An improved method and system for measuring a multi-phase flow in a pressure flow meter. An extended throat venturi is used and pressure of the multi-phase flow is measured at three or more positions in the venturi, which define two or more pressure differentials in the flow conduit. The differential pressures are then used to calculate the mass flow of the gas phase, the total mass flow, and the liquid phase. The system for determining the mass flow of the high void fraction fluid flow and the gas flow includes taking into account a pressure drop experienced by the gas phase due to work performed by the gas phase in accelerating the liquid phase.

  17. Differentiable but exact formulation of density-functional theory

    SciTech Connect (OSTI)

    Kvaal, Simen Ekström, Ulf; Helgaker, Trygve; Teale, Andrew M.; School of Chemistry, University of Nottingham, University Park, Nottingham NG7 2RD

    2014-05-14

    The universal density functional F of density-functional theory is a complicated and ill-behaved function of the density—in particular, F is not differentiable, making many formal manipulations more complicated. While F has been well characterized in terms of convex analysis as forming a conjugate pair (E, F) with the ground-state energy E via the Hohenberg–Kohn and Lieb variation principles, F is nondifferentiable and subdifferentiable only on a small (but dense) subset of its domain. In this article, we apply a tool from convex analysis, Moreau–Yosida regularization, to construct, for any ε > 0, pairs of conjugate functionals ({sup ε}E, {sup ε}F) that converge to (E, F) pointwise everywhere as ε → 0{sup +}, and such that {sup ε}F is (Fréchet) differentiable. For technical reasons, we limit our attention to molecular electronic systems in a finite but large box. It is noteworthy that no information is lost in the Moreau–Yosida regularization: the physical ground-state energy E(v) is exactly recoverable from the regularized ground-state energy {sup ε}E(v) in a simple way. All concepts and results pertaining to the original (E, F) pair have direct counterparts in results for ({sup ε}E, {sup ε}F). The Moreau–Yosida regularization therefore allows for an exact, differentiable formulation of density-functional theory. In particular, taking advantage of the differentiability of {sup ε}F, a rigorous formulation of Kohn–Sham theory is presented that does not suffer from the noninteracting representability problem in standard Kohn–Sham theory.

  18. Using Algorithmic Differentiation to Increase Sensitivity of Piezoelectric

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Transducers with Respect to Material Parameters | Argonne Leadership Computing Facility Using Algorithmic Differentiation to Increase Sensitivity of Piezoelectric Transducers with Respect to Material Parameters Event Sponsor: Mathematics and Computer Science Division LANS Seminar Start Date: Aug 24 2016 - 3:00pm Building/Room: Building 240/Room 1404-1405 Location: Argonne National Laboratory Speaker(s): Benjamin Jurgelucks Speaker(s) Title: University of Paderborn Event Website:

  19. DIFFERENTIAL GROUP-VELOCITY DETECTION OF FLUID PATHS

    SciTech Connect (OSTI)

    Leland Timothy Long

    2005-12-20

    For nearly 50 years, surface waves that propagate through near-surface soils have been utilized in engineering for the determination of the small-strain dynamic properties of soils. These techniques, although useful, have not been sufficiently precise to use in detecting the subtle changes in soil properties that accompany short-term changes in fluid content. The differential techniques developed in this research now make it possible to monitor small changes (less than 3 cm) in the water level of shallow soil aquifers. Using inversion techniques and tomography, differential seismic techniques could track the water level distribution in aquifers with water being pumped in or out. Differential surface wave analysis could lead to new ways to monitor reservoir levels and verify hydrologic models. Field data obtained during this investigation have measured changes in surface-wave phase and group velocity before and after major rain events, and have detected subtle changes associated with pumping water into an aquifer and pumping water out of an aquifer. This research has established analysis techniques for observing these changes. These techniques combine time domain measurements to isolate surface wave arrivals with frequency domain techniques to determine the effects as a function of frequency. Understanding the differences in response as a function of wave frequency facilitates the inversion of this data for soil velocity structure. These techniques have also quantified many aspects of data acquisition and analysis that are important for significant results. These include tight control on the character of the source and proper placement of the geophones. One important application is the possibility that surface waves could be used to monitor and/or track fluid movement during clean-up operations, verifying that the fluid reached all affected areas. Extending this to a larger scale could facilitate monitoring of water resources in basins without having to drill many

  20. An Advanced Liquid Centrifuge Using Differentially Rotating Cylinders and

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Optimized Boundary Conditions --- Inventor(s) Hantao Ji, Adam Cohen, Phil Efthimion and Eric Edlund | Princeton Plasma Physics Lab An Advanced Liquid Centrifuge Using Differentially Rotating Cylinders and Optimized Boundary Conditions --- Inventor(s) Hantao Ji, Adam Cohen, Phil Efthimion and Eric Edlund This invention discloses a concept for an advanced centrifugal contactor which can be used for (1) mixing of two or more component fluid substances to produce a uniform mixture or enhance the