Powered by Deep Web Technologies
Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Darshan Darshan-Ruby  

NLE Websites -- All DOE Office Websites (Extended Search)

to simplify Darshan log analysis in Ruby. Darshan-Ruby uses the Darshan logutils API to efficiently access Darshan data without intermediate conversion into text format....

2

Floodplain Assessment for the Proposed Engineered Erosion Controls at TA-72 in Lower Sandia Canyon, Los Alamos National Laboratory  

SciTech Connect

Los Alamos National Laboratory (LANL) is preparing to implement engineering controls in Sandia Canyon at Technical Area (TA) 72. Los Alamos National Security (LANS) biologists conducted a floodplain determination and this project is located within a 100-year floodplain. The proposed project is to rehabilitate the degraded channel in lower Sandia Canyon where it crosses through the outdoor firing range at TA-72 to limit the loss of sediment and dissipate floodwater leaving LANL property (Figure 1). The proposed construction of these engineered controls is part of the New Mexico Environment Department's (NMED) approved LANL Individual Storm Water Permit. The purpose of this project is to install storm water controls at Sandia Watershed Site Monitoring Area 6 (S-SMA-6). Storm water controls will be designed and installed to meet the requirements of NPDES Permit No. NM0030759, commonly referred to as the LANL Individual Storm Water Permit (IP). The storm water control measures address storm water mitigation for the area within the boundary of Area of Concern (AOC) 72-001. This action meets the requirements of the IP for S-SMA-6 for storm water controls by a combination of: preventing exposure of upstream storm water and storm water generated within the channel to the AOC and totally retaining storm water falling outside the channel but within the AOC.

Hathcock, Charles D. [Los Alamos National Laboratory

2012-08-27T23:59:59.000Z

3

Women @ Energy: Ruby Leung | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

Ruby Leung Ruby Leung Women @ Energy: Ruby Leung April 3, 2013 - 12:06pm Addthis Dr. Ruby Leung, Pacific Northwest National Laboratory, builds accurate, intricate computer models that allow researchers and stakeholders to understand the interplay between Earth, water, clouds, and atmosphere. Dr. Ruby Leung, Pacific Northwest National Laboratory, builds accurate, intricate computer models that allow researchers and stakeholders to understand the interplay between Earth, water, clouds, and atmosphere. Check out other profiles in the Women @ Energy series and share your favorites on Pinterest. Building accurate, intricate computer models that allow scientists and stakeholders to understand the interplay between earth, water, clouds, and atmosphere is what Dr. Ruby Leung does at Pacific Northwest National

4

Women @ Energy: Ruby Leung | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Ruby Leung Ruby Leung Women @ Energy: Ruby Leung April 3, 2013 - 12:06pm Addthis Dr. Ruby Leung, Pacific Northwest National Laboratory, builds accurate, intricate computer models that allow researchers and stakeholders to understand the interplay between Earth, water, clouds, and atmosphere. Dr. Ruby Leung, Pacific Northwest National Laboratory, builds accurate, intricate computer models that allow researchers and stakeholders to understand the interplay between Earth, water, clouds, and atmosphere. Check out other profiles in the Women @ Energy series and share your favorites on Pinterest. Building accurate, intricate computer models that allow scientists and stakeholders to understand the interplay between earth, water, clouds, and atmosphere is what Dr. Ruby Leung does at Pacific Northwest National

5

U-148: ActiveScriptRuby GRScript18.dll ActiveX Control Ruby Code Execution  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

48: ActiveScriptRuby GRScript18.dll ActiveX Control Ruby Code 48: ActiveScriptRuby GRScript18.dll ActiveX Control Ruby Code Execution Vulnerability U-148: ActiveScriptRuby GRScript18.dll ActiveX Control Ruby Code Execution Vulnerability April 16, 2012 - 7:00am Addthis PROBLEM: A vulnerability has been reported in ActiveScriptRuby, which can be exploited by malicious people to potentially compromise a user's system. PLATFORM: Version(s): 1.2.2.0 and prior ABSTRACT: The vulnerability is caused due to an error in GRScript18.dll and can be exploited to execute arbitrary Ruby commands. reference LINKS: Secunia Advisory 48811 CVE-2012-1241 IMPACT ASSESSMENT: High Discussion: ActiveScriptRuby is a software to implement Ruby into a Windows environment. ActiveScriptRuby contains a vulnerability where an arbitrary Ruby script may be executed on the web browser that can execute ActiveX

6

Ruby natural gas pipeline begins service today (July 28, 2011 ...  

U.S. Energy Information Administration (EIA)

El Paso Corporation's Ruby Pipeline (Ruby), the largest natural gas pipeline project dedicated to serving the Western United States since the ...

7

On Secure Key Management in Mobile Ad Hoc Networks Dahai Xu Jeffrey Dwoskin Jianwei Huang Mung Chiang Ruby Lee  

E-Print Network (OSTI)

Chiang Ruby Lee Abstract--It is widely believed that although being more complex, a probabilistic key: dahaixu@research.att.com). J. Dwoskin, M. Chiang and R. Lee are with Department of Electrical Engineering

Chiang, Mung

8

Ruby, Alaska: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

Ruby, Alaska: Energy Resources Ruby, Alaska: Energy Resources (Redirected from Ruby, AK) Jump to: navigation, search Equivalent URI DBpedia Coordinates 64.7394444°, -155.4869444° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":64.7394444,"lon":-155.4869444,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

9

ACCELERATED PILOT PROJECT FOR U CANYON DEMOLITION  

SciTech Connect

At the U.S. Department of Energy's Hanford Site in southeast Washington State, CH2M HILL Plateau Remediation Company (CH2M HILL) is underway on a first-of-a-kind project with the decommissioning and demolition of the U Canyon. Following the U.S. Environmental Protection Agency's Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) Record of Decision for the final remediation of the canyon, CH2M HILL is combining old and new technology and techniques to prepare U Canyon for demolition. The selected remedial action called first for consolidating and grouting equipment currently in the canyon into lower levels of the plant (openings called cells), after which the cell galleries, hot pipe trench, ventilation tunnel, drains and other voids below the operating deck and crane-way deck levels will be filled with approximately 20,000 cubic yards of grout and the canyon roof and walls demolished down to the approximate level of the canyon deck. The remaining canyon structure will then be buried beneath an engineered barrier designed to control potential contaminant migration for a 500-year life. Methods and lessons learned from this project will set the stage for the future demolition of Hanford's four other canyon-type processing facilities.

KEHLER KL

2011-01-13T23:59:59.000Z

10

U-157: Ruby Mail Gem Directory Traversal and Shell Command Injection...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

57: Ruby Mail Gem Directory Traversal and Shell Command Injection Vulnerabilities U-157: Ruby Mail Gem Directory Traversal and Shell Command Injection Vulnerabilities April 27,...

11

Influence of radiation damage on ruby as a pressure gauge  

SciTech Connect

This study tackles the question if ruby crystals, irradiated with energetic heavy ions, can still be used as reliable pressure sensors. The problem is linked to novel irradiation experiments, exposing pressurized samples to swift heavy-ion beams. In order to test and quantify a possible influence of radiation damage on the laser-induced fluorescence lines of ruby (Al{sub 2}O{sub 3}:Cr{sup 3+}), small crystals were exposed to different heavy ions (Xe, Au, and U) with kinetic energies of several giga-electron volt at ambient as well as high-pressure conditions. With increasing fluence (ions/cm{sup 2}), the R{sub 1} and R{sub 2} lines shift both to lower wavelengths which leads to an underestimation of the pressure. An empirical correction term {epsilon} is proposed to include the irradiation damage effect into the commonly employed ruby calibration scale.

Schuster, B. [Institut fuer Festkoerperphysik, Technische Universitaet Darmstadt, Hochschulstrasse 6, 64289 Darmstadt (Germany); GSI Helmholtzzentrum fuer Schwerionenforschung, Planckstr. 1, 64291 Darmstadt (Germany); Weikusat, C.; Miletich, R. [Universitaet Heidelberg, Im Neuenheimer Feld 234-236, 69120 Heidelberg (Germany); Trautmann, C.; Neumann, R. [GSI Helmholtzzentrum fuer Schwerionenforschung, Planckstr. 1, 64291 Darmstadt (Germany); Fujara, F. [Institut fuer Festkoerperphysik, Technische Universitaet Darmstadt, Hochschulstrasse 6, 64289 Darmstadt (Germany)

2010-11-01T23:59:59.000Z

12

Upper Los Alamos Canyon Cleanup  

NLE Websites -- All DOE Office Websites (Extended Search)

Upper Los Alamos Canyon Cleanup Upper Los Alamos Canyon Cleanup Upper Los Alamos Canyon Cleanup The Upper Los Alamos Canyon Project involves cleaning up hazardous materials left over from some of the Laboratory's earliest activities. Contact Environmental Communication & Public Involvement P.O. Box 1663 MS M996 Los Alamos, NM 87545 (505) 667-0216 Email Located along Los Alamos Canyon from 7th Street to the Pajarito Ski Hill, the Upper Los Alamos Canyon Project involves examining sites in present and former Laboratory technical areas to see if any further environmental cleanup actions are needed. If not, the Laboratory can apply to have these sites removed permanently from LANL's Hazardous Waste Permit, meaning that no further actions are needed at those sites. Among the 115 sites included in the Upper LA Canyon Project, 54 have been

13

Ruby Pipeline ramps up rapidly to supply natural gas to ...  

U.S. Energy Information Administration (EIA)

A B C D E F G H I J K L M N O P Q R S T U V W XYZ. Today in Energy. ... PG&E's overall natural gas needs have changed little since late July when Ruby began flowing ...

14

Upper Los Alamos Canyon Cleanup  

NLE Websites -- All DOE Office Websites (Extended Search)

septic tanks, sanitary and industrial waste lines, storm drains, incinerators, transformer sites, and areas in which soil has been contaminated. The Upper Los Alamos Canyon...

15

California Nuclear Profile - Diablo Canyon  

U.S. Energy Information Administration (EIA) Indexed Site

Diablo Canyon" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License expiration date"...

16

RUBY NANDINI GHOSH Research Associate Professor  

E-Print Network (OSTI)

University 1996 to 2004 "Wide bandgap semiconductor devices" Catalytic gate silicon carbide devices have been & Engineering Physics (1991) Thesis: "Spin Dependent Transport in a Silicon Two-Dimensional Electron Gas degradation in performance. "Fiber optic oxygen sensing" Developed a reflection mode fiber probe operating

Ghosh, Ruby N.

17

Generation of coherent terahertz pulses in ruby at room temperature  

Science Conference Proceedings (OSTI)

We have shown that a coherently driven solid state medium can potentially produce strong controllable short pulses of THz radiation. The high efficiency of the technique is based on excitation of maximal THz coherence by applying resonant optical pulses to the medium. The excited coherence in the medium is connected to macroscopic polarization coupled to THz radiation. We have performed detailed simulations by solving the coupled density matrix and Maxwell equations. By using a simple V-type energy scheme for ruby, we have demonstrated that the energy of generated THz pulses ranges from hundreds of pico-Joules to nano-Joules at room temperature and micro-Joules at liquid helium temperature, with pulse durations from picoseconds to tens of nanoseconds. We have also suggested a coherent ruby source that lases on two optical wavelengths and simultaneously generates THz radiation. We discussed also possibilities of extension of the technique to different solid-state materials.

Kuznetsova, Elena; Rostovtsev, Yuri; Kalugin, Nikolai G.; Kolesov, Roman; Kocharovskaya, Olga [Institute for Quantum Studies and Department of Physics, Texas A and M University, College Station, Texas 77843 (United States); Scully, Marlan O. [Institute for Quantum Studies and Department of Physics, Texas A and M University, College Station, Texas 77843 (United States); Princeton Institute for Material Science and Department of Mechanical and Aerospace Engineering, Princeton University, New Jersey 08544 (United States)

2006-08-15T23:59:59.000Z

18

U-157: Ruby Mail Gem Directory Traversal and Shell Command Injection  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

57: Ruby Mail Gem Directory Traversal and Shell Command 57: Ruby Mail Gem Directory Traversal and Shell Command Injection Vulnerabilities U-157: Ruby Mail Gem Directory Traversal and Shell Command Injection Vulnerabilities April 27, 2012 - 7:00am Addthis PROBLEM: Ruby Mail Gem Directory Traversal and Shell Command Injection Vulnerabilities PLATFORM: Mail gem for Ruby 2.x ABSTRACT: Some vulnerabilities have been reported in the Mail gem for Ruby, which can be exploited by malicious people to manipulate certain data and compromise a vulnerable system. Reference Links: Secunia Advisory SA48970 CVE-2012-2139 CVE-2012-2140 IMPACT ASSESSMENT: Medium Discussion: Input passed via the "to" parameter within the file delivery method is not properly verified before being used and can be exploited to modify arbitrary files via directory traversal attacks. Certain input passed to

19

New York Canyon Stimulation  

Science Conference Proceedings (OSTI)

The New York Canyon Stimulation Project was to demonstrate the commercial application of Enhanced Geothermal System techniques in Buena Vista Valley area of Pershing County, Nevada. From October 2009 to early 2012, TGP Development Company aggressively implemented Phase I of Pre-Stimulation and Site/Wellbore readiness. This included: geological studies; water studies and analyses and procurement of initial permits for drilling. Oversubscription of water rights and lack of water needed for implementation of EGS were identified and remained primary obstacles. Despite extended efforts to find alternative solutions, the water supply circumstances could not be overcome and led TGP to determine a "????No Go"??? decision and initiate project termination in April 2012.

Raemy, B. Principal Investigator, TGP Development Company, LLC

2012-06-21T23:59:59.000Z

20

Post-project appraisal of Martin Canyon Creek restoration  

E-Print Network (OSTI)

Haltiner, Jeffery. 1997. Martin Canyon Stream Stabilization:Williams & Associates, Ltd. 1999. Martin Canyon Creek StreamPost-Project Appraisal of Martin Canyon Creek Restoration

Wagner, Wayne; Roseman, Jesse

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Hudson Canyon | Open Energy Information  

Open Energy Info (EERE)

Canyon Canyon Jump to: navigation, search Name Hudson Canyon Facility Hudson Canyon Sector Wind energy Facility Type Offshore Wind Facility Status Proposed Owner Deepwater Wind Long Island Developer Deepwater Wind Location Atlantic Ocean NY Coordinates 40.151°, -73.53° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":40.151,"lon":-73.53,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

22

Juniper Canyon | Open Energy Information  

Open Energy Info (EERE)

Juniper Canyon Juniper Canyon Jump to: navigation, search Name Juniper Canyon Facility Juniper Canyon Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Iberdrola Developer Iberdrola Energy Purchaser Merchant Location In Klickitat County 4.6 miles Southeast of Goldendale Coordinates 45.910223°, -120.224317° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":45.910223,"lon":-120.224317,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

23

Pacific Gas & Electric Company, Diablo Canyon Nuclear ...  

Science Conference Proceedings (OSTI)

Pacific Gas & Electric Company, Diablo Canyon Nuclear Power Plant. NVLAP Lab Code: 100537-0. Address and Contact Information: ...

2013-11-08T23:59:59.000Z

24

Pacific Gas & Electric Company, Diablo Canyon Nuclear ...  

Science Conference Proceedings (OSTI)

Pacific Gas & Electric Company, Diablo Canyon Nuclear Power Plant. NVLAP Lab Code: 100537-0. Address and Contact Information: ...

2013-08-23T23:59:59.000Z

25

Internal Tides in Monterey Submarine Canyon  

Science Conference Proceedings (OSTI)

The M2 internal tide in Monterey Submarine Canyon is simulated using a modified version of the Princeton Ocean Model. Most of the internal tide energy entering the canyon is generated to the south, on Sur Slope and at the head of Carmel Canyon. ...

Rob A. Hall; Glenn S. Carter

2011-01-01T23:59:59.000Z

26

Electron number density measurement by ruby laser interferometry  

DOE Green Energy (OSTI)

A pulsed ruby laser beam with 3 nsec full width at half magnitude is used to obtain space- and time-resolved, two-dimensional interferometric measurements of electron number density in CO/sub 2/-laser produced plasma in hydrogen near the focal spot. The focal plane of the CO/sub 2/ laser is arranged to be at the exit of a free-expansion jet, with the beam incident from the vacuum side. Several nanoseconds after breakdown, a shock wave is formed, propagating transverse to the incident laser beam direction. Behind the transverse propagating shock is an on axis density minimum, which results in laser-beam self trapping. During the initial pulse duration of the CO/sub 2/ laser, the radial boundary of the plasma column increases linearly in time.

Chu, T.K.; Johnson, L.C.; Schuss, J.J.

1977-01-01T23:59:59.000Z

27

Attachments for fire modeling for Building 221-T, T Plant canyon deck and railroad tunnel  

SciTech Connect

The purpose of this attachment is to provide historical information and documentation for Document No. WHC-SD-CP-ANAL-008 Rev 0, ``Fire Modeling for Building 221-T--T Plant Canyon Deck and Railroad Tunnel``, dated September 29, 1994. This data compilation contains the following: Resumes of the Technical Director, Senior Engineer and Junior Engineer; Review and Comment Record; Software Files; CFAST Input and Output Files; Calculation Control Sheets; and Estimating Sprinkler Actuation Time in the Canyon and Railroad Tunnel. The T Plant was originally a fuel reprocessing facility. It was modified later to decontaminate and repair PuRex process equipment.

Oar, D.L. [Westinghouse Hanford Co., Richland, WA (United States)

1995-01-23T23:59:59.000Z

28

Intense, Variable Mixing near the Head of Monterey Submarine Canyon  

Science Conference Proceedings (OSTI)

A microstructure survey near the head of Monterey Submarine Canyon, the first in a canyon, confirmed earlier inferences that coastal submarine canyons are sites of intense mixing. The data collected during two weeks in August 1997 showed ...

Glenn S. Carter; Michael C. Gregg

2002-11-01T23:59:59.000Z

29

Pages that link to "Coyote Canyon Steam Plant Biomass Facility...  

Open Energy Info (EERE)

Share this page on Facebook icon Twitter icon Pages that link to "Coyote Canyon Steam Plant Biomass Facility" Coyote Canyon Steam Plant Biomass Facility Jump to:...

30

Changes related to "Coyote Canyon Steam Plant Biomass Facility...  

Open Energy Info (EERE)

Share this page on Facebook icon Twitter icon Changes related to "Coyote Canyon Steam Plant Biomass Facility" Coyote Canyon Steam Plant Biomass Facility Jump to:...

31

DOE - Office of Legacy Management -- Burro Canyon Disposal Cell...  

Office of Legacy Management (LM)

Burro Canyon Disposal Cell - 007 FUSRAP Considered Sites Site: Burro Canyon Disposal Cell (007) Designated Name: Alternate Name: Location: Evaluation Year: Site Operations: Site...

32

DOE - Office of Legacy Management -- Bodo Canyon Cell - 006  

Office of Legacy Management (LM)

Bodo Canyon Cell - 006 FUSRAP Considered Sites Site: Bodo Canyon Cell (006) Designated Name: Alternate Name: Location: Evaluation Year: Site Operations: Site Disposition:...

33

EIS-0219: F-Canyon Plutonium Solutions | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

of Plutonium Solutions Stored in the F-Canyon Facility, Savannah River Site, Aiken, SC December 1, 1994 EIS-0219: Final Environmental Impact Statement F-Canyon Plutonium...

34

Bear Canyon Geothermal Facility | Open Energy Information  

Open Energy Info (EERE)

Canyon Geothermal Facility Canyon Geothermal Facility Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Bear Canyon Geothermal Facility General Information Name Bear Canyon Geothermal Facility Facility Bear Canyon Sector Geothermal energy Location Information Location Clear Lake, California, Coordinates 38.762851116528°, -122.69217967987° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":38.762851116528,"lon":-122.69217967987,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

35

Microsoft Word - CX-BadgerCanyon-RichlandNo1_WoodPoles_FY13.docx  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7, 2013 7, 2013 REPLY TO ATTN OF: KEPR/Pasco SUBJECT: Environmental Clearance Memorandum Walker Miller Electrical Engineer - TPCF-W RICHLAND Proposed Action: Wood pole replacements on the Badger Canyon-Richland #1 transmission line PP&A Project No.: 2670 Categorical Exclusion Applied (from Subpart D, 10 C.F.R. Part 1021): B1.3 Routine maintenance activities. Location: City of Richland, Benton County, WA Transmission Line/ROW Structure # Township Range Section County, State Badger Canyon-Richland #1 4/9 and 4/10 9N 28E 26 Benton, WA Proposed by: Bonneville Power Administration (BPA) Description of the Proposed Action: BPA, at the expense of the City of Richland, proposes to raise structures 4/9 and 4/10 of the Badger Canyon-Richland #1 115-kilovolt transmission line to

36

Hay Canyon Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Hay Canyon Wind Farm Hay Canyon Wind Farm Jump to: navigation, search Name Hay Canyon Wind Farm Facility Hay Canyon Wind Farm Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Iberdrola Renewables Developer Iberdrola Renewables Energy Purchaser Snohomish Public Utility District Location Near Moro OR Coordinates 45.479548°, -120.741491° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":45.479548,"lon":-120.741491,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

37

Spring Canyon Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Spring Canyon Wind Farm Spring Canyon Wind Farm Jump to: navigation, search Name Spring Canyon Wind Farm Facility Spring Canyon Wind Farm Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Invenergy Developer Invenergy Energy Purchaser Xcel Energy Location Near Peetz CO Coordinates 40.95366°, -103.166993° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":40.95366,"lon":-103.166993,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

38

Threemile Canyon Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Threemile Canyon Wind Farm Threemile Canyon Wind Farm Jump to: navigation, search Name Threemile Canyon Wind Farm Facility Threemile Canyon Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner John Deere Wind Developer John Deere Wind Energy Purchaser PacifiCorp Location Morrow County OR Coordinates 45.837861°, -119.701286° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":45.837861,"lon":-119.701286,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

39

Three Mile Canyon | Open Energy Information  

Open Energy Info (EERE)

Mile Canyon Mile Canyon Jump to: navigation, search Name Three Mile Canyon Facility Three Mile Canyon Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner John Deere Wind Developer Momentum RE Energy Purchaser PacifiCorp Location Morrow County OR Coordinates 45.717419°, -119.502258° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":45.717419,"lon":-119.502258,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

40

Turbulent Kinetic Energy Dissipation in Barrow Canyon  

Science Conference Proceedings (OSTI)

Pacific Water flows across the shallow Chukchi Sea before reaching the Arctic Ocean, where it is a source of heat, freshwater, nutrients, and carbon. A substantial portion of Pacific Water is routed through Barrow Canyon, located in the northeast ...

E. L. Shroyer

2012-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Internal Waves in Monterey Submarine Canyon  

Science Conference Proceedings (OSTI)

Velocity, temperature, and salinity profile surveying in Monterey Submarine Canyon during spring tide reveals an internal wave field almost an order of magnitude more energetic than that in the open ocean. Semidiurnal fluctuations and their ...

Eric Kunze; Leslie K. Rosenfeld; Glenn S. Carter; Michael C. Gregg

2002-06-01T23:59:59.000Z

42

Rectified Barotropic Flow over a Submarine Canyon  

Science Conference Proceedings (OSTI)

The effect of an isolated canyon interrupting a long continental shelf of constant cross section on the along-isobath, oscillatory motion of a homogeneous, incompressible fluid is considered by employing laboratory experiments (physical models) ...

Nicolas Pernne; Jacques Verron; Dominique Renouard; Don L. Boyer; Xiuzhang Zhang

1997-09-01T23:59:59.000Z

43

Engineers Constructors  

Office of Legacy Management (LM)

Engineers Engineers - Constructors ~ /:~ ( ' r,.... I!~\ l.,_",z;(J;' Bechtel National, Inc. Oak Ridge Office Jackson Plaza Tower 800 Oak Ridge Turnpike Oak Ridge. Tennessee Mail Address: P. O. B01l 350. Oak Ridge. TN 37830 bce-. R. Barber C. t1iller E. Wal ker C. Knoke G. Phillips G. Scott L. Blevins K. Harer DOE File No. 030-04G Professional Land Surveying 1404 Second Street Santa Fe, New Mexico 87501 Attn: Mr. Robert Benavides Reference: Purchase Contract l4501-01j04-PC-19 Bayo Canyon Survey Dear Mr. Benavides: The following are clarifications to the referenced contract specification. The need for clarification to the specification arises from the fact that the Bayo Canyon site is transected by a corporate boundary, the Los Alamos County-Santa Fe County line. This condition affects three items in the specification Scope Of Work: Item 1.2.5, the as-built site plan of the Bayo

44

Physical Modeling of Flow Field inside Urban Street Canyons  

Science Conference Proceedings (OSTI)

The flow characteristics inside urban street canyons were studied in a laboratory water channel. The approaching flow direction was horizontal and perpendicular to the street axis. The street width was adjusted to form street canyons of aspect ...

Xian-Xiang Li; Dennis Y. C. Leung; Chun-Ho Liu; K. M. Lam

2008-07-01T23:59:59.000Z

45

Wintertime Boundary Layer Structure in the Grand Canyon  

Science Conference Proceedings (OSTI)

Wintertime temperature profiles in the Grand Canyon exhibit a neutral to isothermal stratification during both daytime and nighttime, with only rare instances of actual temperature inversions. The canyon warms during daytime and cools during ...

C. David Whiteman; Shiyuan Zhong; Xindi Bian

1999-08-01T23:59:59.000Z

46

Coyote Canyon Geothermal Project | Open Energy Information  

Open Energy Info (EERE)

Coyote Canyon Geothermal Project Coyote Canyon Geothermal Project Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Development Project: Coyote Canyon Geothermal Project Project Location Information Coordinates 39.723055555556°, -118.08027777778° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":39.723055555556,"lon":-118.08027777778,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

47

Red Canyon Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Red Canyon Wind Farm Red Canyon Wind Farm Facility Red Canyon Wind Farm Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner NextEra Energy Resources Developer Florida Power & Light Co. Location Borden TX Coordinates 32.95326011°, -101.215539° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":32.95326011,"lon":-101.215539,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

48

Devil's Canyon Geothermal Project | Open Energy Information  

Open Energy Info (EERE)

Devil's Canyon Geothermal Project Devil's Canyon Geothermal Project Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Development Project: Devil's Canyon Geothermal Project Project Location Information Coordinates 40.938333333333°, -117.53916666667° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":40.938333333333,"lon":-117.53916666667,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

49

Biglow Canyon Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Biglow Canyon Wind Farm Biglow Canyon Wind Farm Facility Biglow Canyon Wind Farm Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Portland General Electric Developer Orion/Portland General Electric Energy Purchaser Portland General Electric Location Sherman County OR Coordinates 45.629003°, -120.605607° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":45.629003,"lon":-120.605607,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

50

Electron beam physical vapor deposition of thin ruby films for remote temperature sensing  

SciTech Connect

Thermographic phosphors (TGPs) possessing temperature-dependent photoluminescence properties have a wide range of uses in thermometry due to their remote access and large temperature sensitivity range. However, in most cases, phosphors are synthesized in powder form, which prevents their use in high resolution micro and nanoscale thermal microscopy. In the present study, we investigate the use of electron beam physical vapor deposition to fabricate thin films of chromium-doped aluminum oxide (Cr-Al{sub 2}O{sub 3}, ruby) thermographic phosphors. Although as-deposited films were amorphous and exhibited weak photoluminescence, the films regained the stoichiometry and {alpha}-Al{sub 2}O{sub 3} crystal structure of the combustion synthesized source powder after thermal annealing. As a consequence, the annealed films exhibit both strong photoluminescence and a temperature-dependent lifetime that decreases from 2.9 ms at 298 K to 2.1 ms at 370 K. Ruby films were also deposited on multiple substrates. To ensure a continuous film with smooth surface morphology and strong photoluminescence, we use a sapphire substrate, which is thermal expansion coefficient and lattice matched to the film. These thin ruby films can potentially be used as remote temperature sensors for probing the local temperatures of micro and nanoscale structures.

Li Wei; Coppens, Zachary J.; Greg Walker, D.; Valentine, Jason G. [Department of Mechanical Engineering, Vanderbilt University, Nashville, Tennessee 37212 (United States)

2013-04-28T23:59:59.000Z

51

Engineering  

NLE Websites -- All DOE Office Websites (Extended Search)

Engineering Engineering Engineering1354608000000EngineeringSome of these resources are LANL-only and will require Remote Access./No/Questions? 667-5809library@lanl.gov Engineering Some of these resources are LANL-only and will require Remote Access. Key Resources Reference Standards Data Sources Organizations Journals Key Resources Engineering Village Includes Engineering Index (Ei) and Compendex Knovel Handbooks, databases, and eBooks integrated with analytical and search tools IEEE Xplore Full text access to technical literature, standards, and conference proceedings in engineering and technology SPIE Digital Library Full-text papers from SPIE journals and proceedings published since 1998; subject coverage includes optics, photonics, electronic imaging, visual information processing, biomedical optics, lasers, and

52

A Laboratory Model of Urban Street-Canyon Flows  

Science Conference Proceedings (OSTI)

A circulating water channel is constructed to examine urban street-canyon flow. In the cases of an even-notch street canyon in which model buildings on both sides of the street have equal heights, one vortex is observed in model canyons with ...

Jong-Jin Baik; Rae-Seol Park; Hye-Yeong Chun; Jae-Jin Kim

2000-09-01T23:59:59.000Z

53

Engineering  

NLE Websites -- All DOE Office Websites (Extended Search)

Electrodynamics Bioscience, Biosecurity, Health Chemical Science Earth, Space Sciences Energy Engineering High Energy Density Plasmas, Fluids Information Science, Computing,...

54

Microsoft Word - Badger Canyon CXWEB.doc  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

KEC-4 KEC-4 SUBJECT: Environmental Clearance Memorandum David Tripp Project Manager - TEP-CSB-1 Proposed Action: Badger Canyon Substation Radio Communication Tower Project Budget Information: Work Order 00253262 Task 03 Categorical Exclusions Applied (from Subpart D, 10 C.F.R. Part 1021: B1.7 "Acquisition, installation, operation, and removal of communication systems..." B1.19 "Siting, construction, and operation of microwave and radio communication towers and associated facilities..." Location: Badger Canyon Substation, Benton County, Washington - Township 8 North, Range 28 East, Section 1 Proposed by: Bonneville Power Administration (BPA) Description of the Proposed Action: BPA proposes to replace a 40-foot monopole communication

55

Coyote Canyon Geothermal Area | Open Energy Information  

Open Energy Info (EERE)

Coyote Canyon Geothermal Area Coyote Canyon Geothermal Area (Redirected from Coyote Canyon Geothermal Resource Area) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Geothermal Resource Area: Coyote Canyon Geothermal Area Contents 1 Area Overview 2 History and Infrastructure 3 Regulatory and Environmental Issues 4 Exploration History 5 Well Field Description 6 Geology of the Area 7 Geofluid Geochemistry 8 NEPA-Related Analyses (6) 9 Exploration Activities (0) 10 References Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"TERRAIN","zoom":6,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"500px","height":"300px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":39.927105,"lon":-117.927225,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

56

Big Canyon Creek Ecological Restoration Strategy.  

DOE Green Energy (OSTI)

He-yey, Nez Perce for steelhead or rainbow trout (Oncorhynchus mykiss), are a culturally and ecologically significant resource within the Big Canyon Creek watershed; they are also part of the federally listed Snake River Basin Steelhead DPS. The majority of the Big Canyon Creek drainage is considered critical habitat for that DPS as well as for the federally listed Snake River fall chinook (Oncorhynchus tshawytscha) ESU. The Nez Perce Soil and Water Conservation District (District) and the Nez Perce Tribe Department of Fisheries Resources Management-Watershed (Tribe), in an effort to support the continued existence of these and other aquatic species, have developed this document to direct funding toward priority restoration projects in priority areas for the Big Canyon Creek watershed. In order to achieve this, the District and the Tribe: (1) Developed a working group and technical team composed of managers from a variety of stakeholders within the basin; (2) Established geographically distinct sub-watershed areas called Assessment Units (AUs); (3) Created a prioritization framework for the AUs and prioritized them; and (4) Developed treatment strategies to utilize within the prioritized AUs. Assessment Units were delineated by significant shifts in sampled juvenile O. mykiss (steelhead/rainbow trout) densities, which were found to fall at fish passage barriers. The prioritization framework considered four aspects critical to determining the relative importance of performing restoration in a certain area: density of critical fish species, physical condition of the AU, water quantity, and water quality. It was established, through vigorous data analysis within these four areas, that the geographic priority areas for restoration within the Big Canyon Creek watershed are Big Canyon Creek from stream km 45.5 to the headwaters, Little Canyon from km 15 to 30, the mainstem corridors of Big Canyon (mouth to 7km) and Little Canyon (mouth to 7km). The District and the Tribe then used data collected from the District's stream assessment and inventory, utilizing the Stream Visual Assessment Protocol (SVAP), to determine treatment necessary to bring 90% of reaches ranked Poor or Fair through the SVAP up to good or excellent. In 10 year's time, all reaches that were previously evaluated with SVAP will be reevaluated to determine progress and to adapt methods for continued success. Over 400 miles of stream need treatment in order to meet identified restoration goals. Treatments include practices which result in riparian habitat improvements, nutrient reductions, channel condition improvements, fish habitat improvements, invasive species control, water withdrawal reductions, improved hydrologic alterations, upland sediment reductions, and passage barrier removal. The Nez Perce Soil and Water Conservation District (District) and the Nez Perce Tribe Department of Fisheries Resource Management Watershed Division (Tribe) developed this document to guide restoration activities within the Big Canyon Creek watershed for the period of 2008-2018. This plan was created to demonstrate the ongoing need and potential for anadromous fish habitat restoration within the watershed and to ensure continued implementation of restoration actions and activities. It was developed not only to guide the District and the Tribe, but also to encourage cooperation among all stakeholders, including landowners, government agencies, private organizations, tribal governments, and elected officials. Through sharing information, skills, and resources in an active, cooperative relationships, all concerned parties will have the opportunity to join together to strengthen and maintain a sustainable natural resource base for present and future generations within the watershed. The primary goal of the strategy is to address aquatic habitat restoration needs on a watershed level for resident and anadromous fish species, promoting quality habitat within a self-sustaining watershed. Seven objectives have been developed to support this goal: (1) Identify factors limiting quality

Rasmussen, Lynn; Richardson, Shannon

2007-10-01T23:59:59.000Z

57

Big Canyon Creek Ecological Restoration Strategy.  

Science Conference Proceedings (OSTI)

He-yey, Nez Perce for steelhead or rainbow trout (Oncorhynchus mykiss), are a culturally and ecologically significant resource within the Big Canyon Creek watershed; they are also part of the federally listed Snake River Basin Steelhead DPS. The majority of the Big Canyon Creek drainage is considered critical habitat for that DPS as well as for the federally listed Snake River fall chinook (Oncorhynchus tshawytscha) ESU. The Nez Perce Soil and Water Conservation District (District) and the Nez Perce Tribe Department of Fisheries Resources Management-Watershed (Tribe), in an effort to support the continued existence of these and other aquatic species, have developed this document to direct funding toward priority restoration projects in priority areas for the Big Canyon Creek watershed. In order to achieve this, the District and the Tribe: (1) Developed a working group and technical team composed of managers from a variety of stakeholders within the basin; (2) Established geographically distinct sub-watershed areas called Assessment Units (AUs); (3) Created a prioritization framework for the AUs and prioritized them; and (4) Developed treatment strategies to utilize within the prioritized AUs. Assessment Units were delineated by significant shifts in sampled juvenile O. mykiss (steelhead/rainbow trout) densities, which were found to fall at fish passage barriers. The prioritization framework considered four aspects critical to determining the relative importance of performing restoration in a certain area: density of critical fish species, physical condition of the AU, water quantity, and water quality. It was established, through vigorous data analysis within these four areas, that the geographic priority areas for restoration within the Big Canyon Creek watershed are Big Canyon Creek from stream km 45.5 to the headwaters, Little Canyon from km 15 to 30, the mainstem corridors of Big Canyon (mouth to 7km) and Little Canyon (mouth to 7km). The District and the Tribe then used data collected from the District's stream assessment and inventory, utilizing the Stream Visual Assessment Protocol (SVAP), to determine treatment necessary to bring 90% of reaches ranked Poor or Fair through the SVAP up to good or excellent. In 10 year's time, all reaches that were previously evaluated with SVAP will be reevaluated to determine progress and to adapt methods for continued success. Over 400 miles of stream need treatment in order to meet identified restoration goals. Treatments include practices which result in riparian habitat improvements, nutrient reductions, channel condition improvements, fish habitat improvements, invasive species control, water withdrawal reductions, improved hydrologic alterations, upland sediment reductions, and passage barrier removal. The Nez Perce Soil and Water Conservation District (District) and the Nez Perce Tribe Department of Fisheries Resource Management Watershed Division (Tribe) developed this document to guide restoration activities within the Big Canyon Creek watershed for the period of 2008-2018. This plan was created to demonstrate the ongoing need and potential for anadromous fish habitat restoration within the watershed and to ensure continued implementation of restoration actions and activities. It was developed not only to guide the District and the Tribe, but also to encourage cooperation among all stakeholders, including landowners, government agencies, private organizations, tribal governments, and elected officials. Through sharing information, skills, and resources in an active, cooperative relationships, all concerned parties will have the opportunity to join together to strengthen and maintain a sustainable natural resource base for present and future generations within the watershed. The primary goal of the strategy is to address aquatic habitat restoration needs on a watershed level for resident and anadromous fish species, promoting quality habitat within a self-sustaining watershed. Seven objectives have been developed to support this goal: (1) Identify factors limiting quality

Rasmussen, Lynn; Richardson, Shannon

2007-10-01T23:59:59.000Z

58

Engineering  

NLE Websites -- All DOE Office Websites (Extended Search)

Engineering Engineering Lawrence Livermore National Laboratory Home Technologies Core Competencies Showcase Careers Partnerships About Advanced Manufacturing Developing high-performance materials, devices, components, and assemblies enabled by innovative design tools and novel manufacturing techniques Learn more Applied Electromagnetics Supporting the development of electromagnetic systems that are pervasive and paramount to the greater National Security community. Learn more Data Sciences Enabling better decisions through the development and application of state-of-the-art techniques in machine learning, statistics, and decision sciences Learn more Precision Engineering Embracing determinism to guide rigorous design, construction, and metrology of mechatronic systems, instruments, and manufactured components

59

Trail Canyon Geothermal Project | Open Energy Information  

Open Energy Info (EERE)

Trail Canyon Geothermal Project Trail Canyon Geothermal Project Project Location Information Coordinates 38.325555555556°, -114.29388888889° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":38.325555555556,"lon":-114.29388888889,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

60

Panther Canyon Geothermal Project | Open Energy Information  

Open Energy Info (EERE)

Panther Canyon Geothermal Project Panther Canyon Geothermal Project Project Location Information Coordinates 40.549444444444°, -117.57666666667° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":40.549444444444,"lon":-117.57666666667,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Blue Canyon VI | Open Energy Information  

Open Energy Info (EERE)

VI VI Jump to: navigation, search Name Blue Canyon VI Facility Blue Canyon VI Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner EDP Renewables North America LLC Developer EDP Renewables North America LLC Energy Purchaser Merchant Location Lawton OK Coordinates 34.8582°, -98.54752° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":34.8582,"lon":-98.54752,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

62

DOE - Office of Legacy Management -- Acid Pueblo Canyon - NM 03  

NLE Websites -- All DOE Office Websites (Extended Search)

Acid Pueblo Canyon - NM 03 Acid Pueblo Canyon - NM 03 FUSRAP Considered Sites Acid/Pueblo Canyon, NM Alternate Name(s): Radioactive Liquid Waste Treatment Plant (TA-45) Acid/Pueblo and Los Alamos Canyon NM.03-3 Location: Canyons in the Pajarito Plateau Region in Los Alamos County, Los Alamos, NM NM.03-3 Historical Operations: Late 1943 or early 1944, head of the south fork of Acid Canyon received untreated liquid waste containing tritium and isotopes of strontium, cesium, uranium, plutonium, and americium discharged from main acid sewer lines and subsequently from the TA-3 plutonium treatment plant. NM.03-3 Eligibility Determination: Radiological Survey(s): Verification Surveys NM.03-5 NM.03-6 Site Status: Certified- Certification Basis and Federal Register Notice NM.03-2

63

Coyote Canyon Geothermal Area | Open Energy Information  

Open Energy Info (EERE)

Coyote Canyon Geothermal Area Coyote Canyon Geothermal Area Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Geothermal Resource Area: Coyote Canyon Geothermal Area Contents 1 Area Overview 2 History and Infrastructure 3 Regulatory and Environmental Issues 4 Exploration History 5 Well Field Description 6 Geology of the Area 7 Geofluid Geochemistry 8 NEPA-Related Analyses (6) 9 Exploration Activities (0) 10 References Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"TERRAIN","zoom":6,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"500px","height":"300px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":39.927105,"lon":-117.927225,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

64

EIS-0427: Grapevine Canyon Wind Project, Coconino County, Arizona |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

27: Grapevine Canyon Wind Project, Coconino County, Arizona 27: Grapevine Canyon Wind Project, Coconino County, Arizona EIS-0427: Grapevine Canyon Wind Project, Coconino County, Arizona Summary This EIS evaluates the environmental impacts of a proposed wind energy generation project in Coconino County, Arizona, on privately owned ranch lands and trust lands administered by the Arizona State Land Department. The proposed project includes a new transmission tie-line that would cross lands administered by Coconino National Forest and interconnect with DOE's Western Area Power Administration's existing Glen Canyon-Pinnacle Peak transmission lines. Public Comment Opportunities No public comment opportunities available at this time. Documents Available for Download September 11, 2012 EIS-0427: Record of Decision Interconnection of the Grapevine Canyon Wind Project, Coconino County,

65

Klondike III / Biglow Canyon Wind Integration Project  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Proposed Action and Alternatives 2-3 Proposed Action and Alternatives 2-3 Figure 1 Proposed 230-kV Towers and Rights-of-Way Klondike III/Biglow Canyon Wind Integration Project Bonneville Power Administration Proposed Action and Alternatives 2-4 Figure 1, continued CUMULATIVE IMPACTS ANALYSIS, PROPOSED WIND PROJECTS, SHERMAN COUNTY, WASHINGTON March 2006 WEST, Inc. 32 Figure 1. Region map of wind projects proposed for Sherman County. D e s c h u t e s Ri ver C a n y o n C o l u m b ia R i v e r Hwy 19 H w y 2 0 6 H w y 9 7 I 8 4 Grass Valley Moro Wasco Biggs Arlington Condon Fourmile Canyon McDonald Ferry Biggs Junction Deschutes River Crossing The Dalles Complex RM 15.9-16.8 RM 40 Sherman Co Wasco Co G i l l i a m C o Gilliam Co Morrow Co Rowena Plateau Historic Columbia River Highway John D a y R i v e r C a n y o n P:\B\BPAX00000324\0600INFO\GS\arcmap\figures\visiblity_tech_report\fig2_visual_resources_or.mxd January 9, 2006

66

Measurements of the parametric decay of CO/sub 2/ laser radiation into plasma waves at quarter critical density using ruby laser Thomson scattering  

SciTech Connect

We report the results of small-angle ruby laser Thomson scattering measurements of the parametric excitation of plasma waves by CO/sub 2/ laser radiation at quarter-critical density in a laser-heated gas target plasma. From supplementary data obtained from interferometry and large-angle ruby laser scattering we infer that the threshold conditions for a convective decay are satisfied.

Schuss, J.J.; Chu, T.K.; Johnson, L.C.

1977-11-01T23:59:59.000Z

67

Nine Canyon Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Wind Farm Wind Farm Facility Nine Canyon Wind Farm Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Energy Northwest Developer Energy Northwest Energy Purchaser Energy Northwest Location Benton County Coordinates 46.286065°, -119.425532° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":46.286065,"lon":-119.425532,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

68

Blue Canyon Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Wind Farm Wind Farm Facility Blue Canyon Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Babcock & Brown/Horizon Developer Zilkha Renewable/Kirmart Corp. Energy Purchaser Western Farmers' Electric Cooperative Location North of Lawton OK Coordinates 34.852678°, -98.551807° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":34.852678,"lon":-98.551807,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

69

Note: A portable, light-emitting diode-based ruby fluorescence spectrometer for high-pressure calibration  

SciTech Connect

Ruby (Al{sub 2}O{sub 3}, with {approx}0.5 wt. % Cr doping) is one of the most widely used manometers at the giga-Pascal scale. Traditionally, its fluorescence is excited with intense laser sources. Here, I present a simple, robust, and portable design that employs light-emitting diodes (LEDs) instead. This LED-based system is safer in comparison with laser-based ones.

Feng Yejun [Advanced Photon Source, Argonne National Laboratory, Argonne, Illinois 60439 (United States)

2011-04-15T23:59:59.000Z

70

Beneficial Reuse at Bodo Canyon Site | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Services » Environmental Justice » Beneficial Reuse at Bodo Services » Environmental Justice » Beneficial Reuse at Bodo Canyon Site Beneficial Reuse at Bodo Canyon Site The George Washington University Environmental Resource Policy Graduate Program Capstone Project Beneficial Reuse at Bodo Canyon Site Feasibility and Community Support for Photovoltaic Array May 2012 The George Washington University Environmental Resource Policy Graduate Program Capstone Project was an analysis of LM's efforts to support the installation of a commercial solar photovoltaic system at the former uranium mill site near Durango, Colorado. Beneficial Reuse at Bodo Canyon Site More Documents & Publications EA-1770: Final Environmental Assessment Performance of a Permeable Reactive Barrier Using Granular Zero-Valent Iron: FY 2004 Annual Report Durango, Colorado, Disposal Site

71

Olowalu-Ukumehame Canyon Geothermal Area | Open Energy Information  

Open Energy Info (EERE)

Olowalu-Ukumehame Canyon Geothermal Area Olowalu-Ukumehame Canyon Geothermal Area (Redirected from Olowalu-Ukumehame Canyon Area) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Geothermal Resource Area: Olowalu-Ukumehame Canyon Geothermal Area Contents 1 Area Overview 2 History and Infrastructure 3 Regulatory and Environmental Issues 4 Exploration History 5 Well Field Description 6 Geology of the Area 7 Geofluid Geochemistry 8 NEPA-Related Analyses (0) 9 Exploration Activities (4) 10 References Area Overview Geothermal Area Profile Location: Hawaii Exploration Region: Hawaii Geothermal Region GEA Development Phase: 2008 USGS Resource Estimate Mean Reservoir Temp: Estimated Reservoir Volume: Mean Capacity: Click "Edit With Form" above to add content History and Infrastructure Operating Power Plants: 0

72

Canyon Bloomers, Inc Greenhouse Low Temperature Geothermal Facility | Open  

Open Energy Info (EERE)

Canyon Bloomers, Inc Greenhouse Low Temperature Geothermal Facility Canyon Bloomers, Inc Greenhouse Low Temperature Geothermal Facility Jump to: navigation, search Name Canyon Bloomers, Inc Greenhouse Low Temperature Geothermal Facility Facility Canyon Bloomers, Inc Sector Geothermal energy Type Greenhouse Location Buhl, Idaho Coordinates 42.5990714°, -114.7594946° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[]}

73

Tidal Motion in Submarine CanyonsA Laboratory Experiment  

Science Conference Proceedings (OSTI)

The reasons for the large-amplitude tidal motion observed in oceanic submarine canyons have been explored with a laboratory experiment. A barotropic tide was forced in a stratified tank, containing continental shelf-slope topography into which a ...

Peter G. Baines

1983-02-01T23:59:59.000Z

74

Observations of the Internal Tide in Monterey Canyon  

Science Conference Proceedings (OSTI)

Data from two shipboard experiments in 1994, designed to observe the semidiurnal internal tide in Monterey Canyon, reveal semidiurnal currents of about 20 cm s?1, which is an order of magnitude larger than the estimated barotropic tidal currents. ...

Emil T. Petruncio; Leslie K. Rosenfeld; Jeffrey D. Paduan

1998-10-01T23:59:59.000Z

75

Flow Variability in a North American Downtown Street Canyon  

Science Conference Proceedings (OSTI)

Previous field and laboratory studies have indicated that flow and turbulence inside urban areas and, in particular, in street canyons, is very complex and is associated with wakes and vortices developing near buildings. However, a number of open ...

Petra Klein; James V. Clark

2007-06-01T23:59:59.000Z

76

H CANYON PROCESSING IN CORRELATION WITH FH ANALYTICAL LABS  

Science Conference Proceedings (OSTI)

Management of radioactive chemical waste can be a complicated business. H Canyon and F/H Analytical Labs are two facilities present at the Savannah River Site in Aiken, SC that are at the forefront. In fact H Canyon is the only large-scale radiochemical processing facility in the United States and this processing is only enhanced by the aid given from F/H Analytical Labs. As H Canyon processes incoming materials, F/H Labs provide support through a variety of chemical analyses. Necessary checks of the chemical makeup, processing, and accountability of the samples taken from H Canyon process tanks are performed at the labs along with further checks on waste leaving the canyon after processing. Used nuclear material taken in by the canyon is actually not waste. Only a small portion of the radioactive material itself is actually consumed in nuclear reactors. As a result various radioactive elements such as Uranium, Plutonium and Neptunium are commonly found in waste and may be useful to recover. Specific processing is needed to allow for separation of these products from the waste. This is H Canyon's specialty. Furthermore, H Canyon has the capacity to initiate the process for weapons-grade nuclear material to be converted into nuclear fuel. This is one of the main campaigns being set up for the fall of 2012. Once usable material is separated and purified of impurities such as fission products, it can be converted to an oxide and ultimately turned into commercial fuel. The processing of weapons-grade material for commercial fuel is important in the necessary disposition of plutonium. Another processing campaign to start in the fall in H Canyon involves the reprocessing of used nuclear fuel for disposal in improved containment units. The importance of this campaign involves the proper disposal of nuclear waste in order to ensure the safety and well-being of future generations and the environment. As processing proceeds in the fall, H Canyon will have a substantial number of samples being sent to F/H Labs. All analyses of these samples are imperative to safe and efficient processing. The important campaigns to occur would be impossible without feedback from analyses such as chemical makeup of solutions, concentrations of dissolution acids and nuclear material, as well as nuclear isotopic data. The necessity of analysis for radiochemical processing is evident. Processing devoid of F/H Lab's feedback would go against the ideals of a safety-conscious and highly accomplished processing facility such as H Canyon.

Weinheimer, E.

2012-08-06T23:59:59.000Z

77

Nine Canyon III Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Nine Canyon III Wind Farm Nine Canyon III Wind Farm Facility Nine Canyon III Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Energy Northwest Developer Energy Northwest/RES Americas Energy Purchaser Energy Northwest Coordinates 46.286065°, -119.425532° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":46.286065,"lon":-119.425532,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

78

Olowalu-Ukumehame Canyon Geothermal Area | Open Energy Information  

Open Energy Info (EERE)

Olowalu-Ukumehame Canyon Geothermal Area Olowalu-Ukumehame Canyon Geothermal Area Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Geothermal Resource Area: Olowalu-Ukumehame Canyon Geothermal Area Contents 1 Area Overview 2 History and Infrastructure 3 Regulatory and Environmental Issues 4 Exploration History 5 Well Field Description 6 Geology of the Area 7 Geofluid Geochemistry 8 NEPA-Related Analyses (0) 9 Exploration Activities (4) 10 References Area Overview Geothermal Area Profile Location: Hawaii Exploration Region: Hawaii Geothermal Region GEA Development Phase: 2008 USGS Resource Estimate Mean Reservoir Temp: Estimated Reservoir Volume: Mean Capacity: Click "Edit With Form" above to add content History and Infrastructure Operating Power Plants: 0 No geothermal plants listed. Add a new Operating Power Plant

79

Microsoft Word - Final_NineCanyon_CommunicationTowerInstall_CX  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1, 2013 1, 2013 REPLY TO ATTN OF: KEC-4 SUBJECT: Environmental Clearance Memorandum Kelly Gardner, PMP Project Manager, TEP-TPP-1 Proposed Action: Nine Canyon Substation Communication Tower Addition: 331800 McNary Sub Bus Tie Relay Replacements and 310427 McNary-Badger Canyon Transfer Trip Install Categorical Exclusion Applied (from Subpart D, 10 C.F.R. Part 1021): B4.6 - Additions and modifications to transmission facilities Location: Kennewick, Benton County, Washington Proposed by: Bonneville Power Administration (BPA) Description of the Proposed Action: BPA proposes to install a 60-foot communications tower and associated communication equipment at the Benton County Public Utility District's Nine Canyon Substation in Benton County, Washington. The upgrade would involve replacing the

80

Review of the Diablo Canyon probabilistic risk assessment  

SciTech Connect

This report details the review of the Diablo Canyon Probabilistic Risk Assessment (DCPRA). The study was performed under contract from the Probabilistic Risk Analysis Branch, Office of Nuclear Reactor Research, USNRC by Brookhaven National Laboratory. The DCPRA is a full scope Level I effort and although the review touched on all aspects of the PRA, the internal events and seismic events received the vast majority of the review effort. The report includes a number of independent systems analyses sensitivity studies, importance analyses as well as conclusions on the adequacy of the DCPRA for use in the Diablo Canyon Long Term Seismic Program.

Bozoki, G.E.; Fitzpatrick, R.G.; Bohn, M.P. [Sandia National Lab., Albuquerque, NM (United States); Sabek, M.G. [Atomic Energy Authority, Nuclear Regulatory and Safety Center, Cairo (Egypt); Ravindra, M.K.; Johnson, J.J. [EQE Engineering, San Francisco, CA (United States)

1994-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Blue Canyon II Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Blue Canyon II Wind Farm Blue Canyon II Wind Farm Jump to: navigation, search Name Blue Canyon II Wind Farm Facility Blue Canyon II Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Horizon Wind Energy Developer Horizon Wind Energy Energy Purchaser American Electric Power Location North of Lawton OK Coordinates 34.8582°, -98.54752° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":34.8582,"lon":-98.54752,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

82

Biglow Canyon Phase III Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Biglow Canyon Phase III Wind Farm Biglow Canyon Phase III Wind Farm Jump to: navigation, search Name Biglow Canyon Phase III Wind Farm Facility Biglow Canyon Phase III Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Portland General Electric Developer Orion Energy Group Energy Purchaser Portland General Electric Location Sherman County OR Coordinates 45.6375°, -120.605278° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":45.6375,"lon":-120.605278,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

83

Thirty-five years at Pajarito Canyon Site  

SciTech Connect

A history of the research activities performed at the Pajarito Canyon Site from 1946 to 1981 is presented. Critical assemblies described include: the Topsy assembly; Lady Godiva; Godiva 2; Jezebel; Flattop; the Honeycomb assembly for Rover studies; Kiwi-TNT; PARKA reactor; Big Ten; and Plasma Cavity Assembly.

Paxton, H.C.

1981-05-01T23:59:59.000Z

84

Properties of Saltstone Prepared Containing H-Canyon Waste  

Science Conference Proceedings (OSTI)

Saltstone slurries were prepared from solutions made from H-Canyon waste and evaluated for processing properties. Salt solutions prepared with a 1:1 ratio of Tank 50H simulant and H-Canyon blended waste produced slurries that met the processing requirements in Table 2 of the Task Technical and Quality Assurance Plan (TTQAP). Additions of set retarder and antifoam were necessary to meet these processing requirements. The water to premix ratio used to achieve acceptable processing properties was 0.63. Slurries prepared solely with H-Canyon blended waste as the salt solution met the gel time and bleed water requirements, but did not set in the allotted time. Compressive strength samples prepared from the mix with acceptable processing properties had an average compressive strength of 814 psi (Samples with a compressive strength value of >200 psi are acceptable.). Analysis for mercury of the leachate of samples analyzed by the Toxic Characteristic Leaching Procedure (TCLP) indicated a concentration of mercury in the leachate <0.11 mg/L (The limit set by the Environmental Protection Agency (EPA) Resource Conservation and Recovery Act (RCRA) for mercury to require treatment is 0.2 mg/L.). It is recommended that without further testing; Tank 50H be limited to no more than 50 wt% H-Canyon material. It is also recommended that prior to the transfer of Tank 50H to the Saltstone Processing Facility; a sample of the Tank 50H waste be evaluated for processing properties.

Cozzi, A

2005-04-05T23:59:59.000Z

85

Glen Canyon Dam Long-Term Experimental and Management Plan EIS  

NLE Websites -- All DOE Office Websites (Extended Search)

Glen Canyon LTEMP EIS Glen Canyon LTEMP EIS Glen Canyon Dam, a 1,300-MW water-storage and hydroelectric facility is located on the Colorado River upstream of the Grand Canyon. EVS is evaluating the effects of dam operations on the Colorado River. A comprehensive evaluation of Glen Canyon Dam operations and their effects on the Colorado River through the Grand Canyon is being conducted by the Department of the Interior with EVS assistance. The Long-Term Experimental and Management Plan (LTEMP) Environmental Impact Statement (EIS) - the first such evaluation in over 15 years - will examine flow regimes to meet the goals of supplying water for communities, agriculture, and industry and will protect the resources of the Grand Canyon, while providing clean hydropower. The LTEMP EIS, which is expected to be completed by the end of 2013, will

86

Fall Chinook Acclimation Project; Pittsburg Landing, Captain John Rapids, and Big Canyon, Annual Report 2003.  

DOE Green Energy (OSTI)

Fisheries co-managers of U.S. v Oregon supported and directed the construction and operation of acclimation and release facilities for Snake River fall Chinook from Lyons Ferry Hatchery at three sites above Lower Granite Dam. In 1996, Congress instructed the U.S. Army Corps of Engineers (USCOE) to construct, under the Lower Snake River Compensation Plan (LSRCP), final rearing and acclimation facilities for fall Chinook in the Snake River basin to complement their activities and efforts in compensating for fish lost due to construction of the lower Snake River dams. The Nez Perce Tribe (NPT) played a key role in securing funding and selecting acclimation sites, then assumed responsibility for operation and maintenance of the facilities. In 1997, Bonneville Power Administrative (BPA) was directed to fund operations and maintenance (O&M) for the facilities. Two acclimation facilities, Captain John Rapids and Pittsburg Landing, were located on the Snake River between Asotin, WA and Hells Canyon Dam and one facility, Big Canyon, was located on the Clearwater River at Peck. The Capt. John Rapids facility is a single pond while the Pittsburg Landing and Big Canyon sites consist of portable fish rearing tanks assembled and disassembled each year. Acclimation of 450,000 yearling smolts (150,000 each facility) begins in March and ends 6 weeks later. When available, an additional 2,400,000 fall Chinook sub-yearlings may be acclimated for 6 weeks, following the smolt release. The project goal is to increase the naturally spawning population of Snake River fall Chinook salmon upstream of Lower Granite Dam. This is a supplementation project; in that hatchery produced fish are acclimated and released into the natural spawning habitat for the purpose of returning a greater number of spawners to increase natural production. Only Snake River stock is used and production of juveniles occurs at Lyons Ferry Hatchery. This is a long-term project, targeted to work towards achieving delisting goals established by National Marine Fisheries Service (NMFS or NOAA Fisheries) and ultimately to provide fall Chinook adults through the Lower Snake River Compensation Plan program as mitigation for construction and operation of the four lower Snake River dams. Complete adult returns (all age classes) for all three acclimation facilities occurred in the year 2002. Progeny (which would then be natural origin fish) would be counted towards achieving Endangered Species Act delisting criteria. In 2003, a total of 2,138,391 fish weighing 66,201 pounds were released from the three acclimation facilities. The total includes 437,633 yearling fish weighing 44,330 pounds and 1,700,758 sub-yearling fish weighing 21,871 pounds.

McLeod, Bruce

2004-01-01T23:59:59.000Z

87

Fall Chinook Aclimation Project; Pittsburg Landing, Captain John Rapids, and Big Canyon, Annual Report 2001.  

DOE Green Energy (OSTI)

Fisheries co-managers of U.S. v Oregon supported and directed the construction and operation of acclimation and release facilities for Snake River fall Chinook from Lyons Ferry Hatchery at three sites above Lower Granite Dam. In 1996, Congress instructed the U.S. Army Corps of Engineers (USCOE) to construct, under the Lower Snake River Compensation Plan (LSRCP), final rearing and acclimation facilities for fall Chinook in the Snake River basin to complement their activities and efforts in compensating for fish lost due to construction of the lower Snake River dams. The Nez Perce Tribe (NPT) played a key role in securing funding and selecting acclimation sites, then assumed responsibility for operation and maintenance of the facilities. In 1997, Bonneville Power Administrative (BPA) was directed to fund operations and maintenance (O&M) for the facilities. Two acclimation facilities, Captain John Rapids and Pittsburg Landing, are located on the Snake River between Asotin, WA and Hells Canyon Dam and one facility, Big Canyon, is located on the Clearwater River at Peck. The Capt. John Rapids facility is a single pond while the Pittsburg Landing and Big Canyon sites consist of portable fish rearing tanks assembled and disassembled each year. Acclimation of 450,000 yearling smolts (150,000 each facility) begins in March and ends 6 weeks later. When available, an additional 2,400,000 fall Chinook sub-yearlings may be acclimated for 6 weeks, following the smolt release. The project goal is to increase the naturally spawning population of Snake River fall Chinook salmon upstream of Lower Granite Dam. This is a supplementation project; in that hatchery produced fish are acclimated and released into the natural spawning habitat for the purpose of returning a greater number of spawners to increase natural production. Only Snake River stock is used and production of juveniles occurs at Lyons Ferry Hatchery. This is a long-term project, and will ultimately work towards achieving delisting goals established by National Marine Fisheries Service (NMFS). Complete returns for all three acclimation facilities will not occur until the year 2002. Progeny (which would then be natural origin fish protected under the Endangered Species Act) from those returns will be returning for the next five years. In 2001, a total of 2,051,099 fish weighing 59,647 pounds were released from the three acclimation facilities. The total includes 318,932 yearling fish weighing 31,128 pounds and 1,732,167 sub-yearling fish weighing 28,519 pounds. Yearling fish numbers were reduced by Bacterial Kidney Disease (BKD) and sub-yearling acclimation time was limited by record low river water flows.

McLeod, Bruce

2004-01-01T23:59:59.000Z

88

New York Canyon Geothermal Area | Open Energy Information  

Open Energy Info (EERE)

form form View source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit with form History Facebook icon Twitter icon » New York Canyon Geothermal Area Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Geothermal Resource Area: New York Canyon Geothermal Area Contents 1 Area Overview 2 History and Infrastructure 3 Regulatory and Environmental Issues 4 Exploration History 5 Well Field Description 6 Geology of the Area 7 Geofluid Geochemistry 8 NEPA-Related Analyses (6) 9 Exploration Activities (1) 10 References Area Overview Geothermal Area Profile Location: Lovelock, NV Exploration Region: Central Nevada Seismic Zone Geothermal Region GEA Development Phase: None"None" is not in the list of possible values (Phase I - Resource Procurement and Identification, Phase II - Resource Exploration and Confirmation, Phase III - Permitting and Initial Development, Phase IV - Resource Production and Power Plant Construction) for this property.

89

American Canyon Power Plant Biomass Facility | Open Energy Information  

Open Energy Info (EERE)

Biomass Facility Biomass Facility Jump to: navigation, search Name American Canyon Power Plant Biomass Facility Facility American Canyon Power Plant Sector Biomass Facility Type Landfill Gas Location Napa County, California Coordinates 38.5024689°, -122.2653887° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":38.5024689,"lon":-122.2653887,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

90

Coyote Canyon Steam Plant Biomass Facility | Open Energy Information  

Open Energy Info (EERE)

Steam Plant Biomass Facility Steam Plant Biomass Facility Jump to: navigation, search Name Coyote Canyon Steam Plant Biomass Facility Facility Coyote Canyon Steam Plant Sector Biomass Facility Type Landfill Gas Location Orange County, California Coordinates 33.7174708°, -117.8311428° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":33.7174708,"lon":-117.8311428,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

91

New York Canyon Geothermal Project | Open Energy Information  

Open Energy Info (EERE)

New York Canyon Geothermal Project New York Canyon Geothermal Project Project Location Information Coordinates 40.056111111111°, -118.01083333333° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":40.056111111111,"lon":-118.01083333333,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

92

Blue Canyon V Wind Farm | Open Energy Information  

Open Energy Info (EERE)

V Wind Farm V Wind Farm Jump to: navigation, search Name Blue Canyon V Wind Farm Facility Blue Canyon V Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Horizon-EDPR Developer Horizon-EDPR Energy Purchaser Public Service of Oklahoma Location Caddo & Comanche Counties OK Coordinates 34.8582°, -98.54752° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":34.8582,"lon":-98.54752,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

93

New York Canyon Stimulation Geothermal Project | Open Energy Information  

Open Energy Info (EERE)

Stimulation Geothermal Project Stimulation Geothermal Project Jump to: navigation, search Last modified on July 22, 2011. Project Title New York Canyon Stimulation Project Type / Topic 1 Recovery Act: Enhanced Geothermal System Demonstrations Project Type / Topic 2 EGS Demonstration Project Description The projects expected outcomes and benefits are; - Demonstrated commercial viability of the EGS-stimulated reservoir by generating electricity using fluids produced from the reservoir at economic costs. - Significant job creation and preservation and economic development in support of the Recovery Act of 2009. State Nevada Objectives Demonstrate the commercial application of EGS techniques at the New York Canyon (NYC) site in a way that minimizes cost and maximizes opportunities for repeat applications elsewhere.

94

Box Canyon Motel Space Heating Low Temperature Geothermal Facility | Open  

Open Energy Info (EERE)

Motel Space Heating Low Temperature Geothermal Facility Motel Space Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Box Canyon Motel Space Heating Low Temperature Geothermal Facility Facility Box Canyon Motel Sector Geothermal energy Type Space Heating Location Ouray, Colorado Coordinates 38.0227716°, -107.6714487° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[]}

95

Harbison Canyon, California: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

Harbison Canyon, California: Energy Resources Harbison Canyon, California: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 32.8203296°, -116.8300236° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":32.8203296,"lon":-116.8300236,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

96

The Dissolution of Desicooler Residues in H-Canyon Dissolvers  

Science Conference Proceedings (OSTI)

A series of dissolution and characterization studies has been performed to determine if FB-Line residues stored in desicooler containers will dissolve using a modified H-Canyon processing flowsheet. Samples of desicooler materials were used to evaluate dissolving characteristics in the low-molar nitric acid solutions used in H-Canyon dissolvers. The selection for the H-Canyon dissolution of desicooler residues was based on their high-enriched uranium content and trace levels of plutonium. Test results showed that almost all of the enriched uranium will dissolve from the desicooler materials after extended boiling in one molar nitric acid solutions. The residue that contained uranium after completion of the extended boiling cycle consisted of brown solids that had agglomerated into large pieces and were floating on top of the dissolver solution. Addition of tenth molar fluoride to a three molar nitric acid solution containing boron did not dissolve remaining uranium from the brown solids. Only after boiling in an eight molar nitric acid-tenth molar fluoride solution without boron did remaining uranium and aluminum dissolve from the brown solids. The amount of uranium associated with brown solids would be approximately 1.4 percent of the total uranium content of the desicooler materials. The brown solids that remain in the First Uranium Cycle feed will accumulate at the organic/aqueous interface during solvent extraction operations. Most of the undissolved white residue that remained after extended boiling was aluminum oxide containing additional trace quantities of impurities. However, the presence of mercury used in H-Canyon dissolvers should complete the dissolution of these aluminum compounds.

Gray, J.H.

2003-06-23T23:59:59.000Z

97

A review of proposed Glen Canyon Dam interim operating criteria  

DOE Green Energy (OSTI)

Three sets of interim operating criteria for Glen Canyon Dam on the Colorado River have been proposed for the period of November 1991, to the completion of the record of decision for the Glen Canyon Dam environmental impact statement (about 1993). These criteria set specific limits on dam releases, including maximum and minimum flows, up-ramp and down-ramp rates, and maximum daily fluctuation. Under the proposed interim criteria, all of these parameters would be reduced relative to historical operating criteria to protect downstream natural resources, including sediment deposits, threatened and endangered fishes, trout, the aquatic food base, and riparian plant communities. The scientific bases of the three sets of proposed operating criteria are evaluated in the present report:(1) criteria proposed by the Research/Scientific Group, associated with the Glen Canyon Environmental Studies (GCES); (2) criteria proposed state and federal officials charged with managing downstream resources; and (3) test criteria imposed from July 1991, to November 1991. Data from Phase 1 of the GCES and other sources established that the targeted natural resources are affected by dam operations, but the specific interim criteria chosen were not supported by any existing studies. It is unlikely that irreversible changes to any of the resources would occur over the interim period if historical operating criteria remained in place. It is likely that adoption of any of the sets of proposed interim operating criteria would reduce the levels of sediment transport and erosion below Glen Canyon Dam; however, these interim criteria could result in some adverse effects, including the accumulation of debris at tributary mouths, a shift of new high-water-zone vegetation into more flood-prone areas, and further declines in vegetation in the old high water zone.

LaGory, K.; Hlohowskyj, I.; Tomasko, D.; Hayse, J.; Durham, L.

1992-04-01T23:59:59.000Z

98

DOE - Office of Legacy Management -- Bayo Canyon NM Site - NM 01  

NLE Websites -- All DOE Office Websites (Extended Search)

Bayo Canyon NM Site - NM 01 Bayo Canyon NM Site - NM 01 FUSRAP Considered Sites Bayo Canyon, NM Alternate Name(s): Bayo Canyon Area Bayo Canyon (TA-10) Site NM.01-2 Location: Canyon in the Pajarito Plateau Region in Los Alamos County, Los Alamos, NM NM.01-3 Historical Operations: Used in 1944-1961 by the MED and later AEC at Los Alamos National Laboratory as a firing site for conventional and high-explosives experiments involving natural and depleted uranium, strontium, and lanthanum as a radiation source for blast diagnosis. NM.01-3 NM.01-5 Eligibility Determination: Eligible NM.01-1 Radiological Survey(s): Assessment Survey NM.01-3 Site Status: Certified- Certification Basis NM.01-5 NM.01-6 Long-term Care Requirements: Long-Term Surveillance and Maintenance Requirements for Remediated FUSRAP Sites S07566_FUSRAP

99

Nine Canyon Wind Farm Phase II | Open Energy Information  

Open Energy Info (EERE)

Page Page Edit with form History Facebook icon Twitter icon » Nine Canyon Wind Farm Phase II Jump to: navigation, search Name Nine Canyon Wind Farm Phase II Facility Nine Canyon Wind Farm Phase II Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Energy Northwest Developer Energy Northwest Energy Purchaser Energy Northwest Location Benton County Coordinates 46.286065°, -119.425532° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":46.286065,"lon":-119.425532,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

100

Simulating infiltration tests in fractured basalt at the Box Canyon Site, Idaho  

E-Print Network (OSTI)

in the unsaturated zone at the Idaho National Engineeringzone: Box Canyon Site, Idaho. , Rep. LBNL-42925, Lawrencethe U.S. Department of Energy, Idaho Operations Office, DOE

Unger, Andre J.A.; Faybishenko, Boris; Bodvarsson, Gudmundur S.; Simmons, Ardyth M.

2003-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Geologic Investigation of a Potential Site for a Next-Generation Reactor Neutrino Oscillation Experiment -- Diablo Canyon, San Luis Obispo County, CA  

E-Print Network (OSTI)

reactions of a nuclear power plant. Diablo Canyon wasmeters from the nuclear power plant) while having suitableThe Diablo Canyon Nuclear Power Plant site in San Luis

Onishi, Celia Tiemi; Dobson, Patrick; Nakagawa, Seiji; Glaser, Steven; Galic, Dom

2004-01-01T23:59:59.000Z

102

Small mammal study of Sandia Canyon, 1994 and 1995  

SciTech Connect

A wide range of plant and wildlife species utilize water discharged from facilities at Los Alamos National Laboratory (LANL). The purpose of this study was to gather baseline data of small mammal populations and compare small mammal characteristics within three areas of Sandia Canyon, which receives outfall effluents from multiple sources. Three small mammal trapping webs were placed in the upper portion of Sandia Canyon, the first two were centered in a cattail-dominated marsh with a ponderosa pine overstory and the third web was placed in a much drier transition area with a ponderosa pine overstory. Webs 1 and 2 had the highest species diversity indices with deer mice the most commonly captured species in all webs. However, at Web 1, voles, shrews, and harvest mice, species more commonly found in moist habitats, made up a much greater overall percentage (65.6%) than did deer mice and brush mice (34.5%). The highest densities and biomass of animals were found in Web 1 with a continual decrease in density estimates in each web downstream. There is no statistical difference between the mean body weights of deer mice and brush mice between sites. Mean body length was also determined not to be statistically different between the webs (GLM [deer mouse], F = 0.89, p = 0.4117; GLM [brush mouse], F = 2.49, p = 0.0999). Furthermore, no statistical difference between webs was found for the mean lean body masses of deer and brush mice (GLM [deer mouse], F = 2.54, p = 0.0838; GLM [brush mouse], F = 1.60, p = 0.2229). Additional monitoring studies should be conducted in Sandia Canyon so comparisons over time can be made. In addition, rodent tissues should be sampled for contaminants and then compared to background or control populations elsewhere at the Laboratory or at an off-site location.

Bennett, K.; Biggs, J.

1996-11-01T23:59:59.000Z

103

DOE/EA-1521; Environmental Assessment for Spring Canyon Wind Project, Logan County, Colorado  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

EA, Spring Canyon Wind Project ix EA, Spring Canyon Wind Project ix TABLE OF CONTENTS Page 1.0 PURPOSE AND NEED......................................................................................................... 1 1.1 INTRODUCTION ..................................................................................................... 1 1.2 PURPOSE AND NEED............................................................................................. 3 1.2.1 Federal Agency Action ............................................................................... 3 1.2.2 Applicant's Purpose and Need .................................................................... 3 1.3 SCOPING .................................................................................................................. 3

104

Wind-Flow Patterns in the Grand Canyon as Revealed by Doppler Lidar  

Science Conference Proceedings (OSTI)

Many interesting flow patterns were found in the Grand Canyon by a scanning Doppler lidar deployed to the south rim during the 1990 Wintertime Visibility Study. Three are analyzed in this study: 1) flow reversal in the canyon, where the flow in ...

Robert M. Banta; Lisa S. Darby; Pirmin Kaufmann; David H. Levinson; Cui-Juan Zhu

1999-08-01T23:59:59.000Z

105

Debris flow deposition and reworking by the Colorado River in Grand Canyon, Arizona  

E-Print Network (OSTI)

Debris flow deposition and reworking by the Colorado River in Grand Canyon, Arizona Brian J Canyon, Arizona, transport coarse-grained sediment onto debris fans adjacent to the Colorado River and Monument Creeks using photogrammetry of aerial photography taken from 1965 to 2000 and supplemented

106

Ice Climbing in Clear Creek Canyon A climbing trip report by Glenn Murray  

E-Print Network (OSTI)

Ice Climbing in Clear Creek Canyon A climbing trip report by Glenn Murray SUMMARY: I climb ice in to ask about local climbing. The guys there told me there was ice nearby, in Clear Creek Canyon. I. Four pitches? Five? It was time to find a partner. The only ice climber I knew in Denver was a friend

107

Green Canyon Hot Springs Greenhouse Low Temperature Geothermal Facility |  

Open Energy Info (EERE)

Greenhouse Low Temperature Geothermal Facility Greenhouse Low Temperature Geothermal Facility Facility Green Canyon Hot Springs Sector Geothermal energy Type Greenhouse Location Newdale, Idaho Coordinates 43.8832463°, -111.6063483° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[]}

108

Gas Flux Sampling At Olowalu-Ukumehame Canyon Area (Thomas, 1986) | Open  

Open Energy Info (EERE)

Gas Flux Sampling At Olowalu-Ukumehame Canyon Area (Thomas, 1986) Gas Flux Sampling At Olowalu-Ukumehame Canyon Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Gas Flux Sampling At Olowalu-Ukumehame Canyon Area (Thomas, 1986) Exploration Activity Details Location Olowalu-Ukumehame Canyon Area Exploration Technique Gas Flux Sampling Activity Date Usefulness could be useful with more improvements DOE-funding Unknown Notes Soil mercury concentration and radon emanometry surveys were conducted along the stream beds in both Olowalu and Ukumehame Canyons and on the coastal alluvial fans (Cox and Cuff, 1981a). The results of these surveys indicated that a few minor -nomalies might be present. However, the extreme topographic relief in the area did not permit sufficient coverage of the

109

Patterns in biodiversity and distribution of benthic Polychaeta in the Mississippi Canyon, Northern Gulf of Mexico  

E-Print Network (OSTI)

The distribution of benthic polychaetes in the Mississippi Canyon was examined to evaluate impacts of environmental variables on species assemblages. Environmental variables considered included depth, bathymetric slope, hydrographic features, sediment grain size, food availability and sediment contamination. Samples were collected using GOMEX boxcorer. Density decreased with increasing depth exponentially. Diversity exhibited a unimodal pattern with depth with a maximum value in the intermediate depth range (about 1269 m). Deposit feeders were the most abundant feeding guild. Both the feeding guilds and faunal composition could be divided into three groups along the depth gradient: shallow (300 ? 800 m), intermediate (800 ? 1500 m) and deep (> 1500 m). Results of statistical analyses revealed that depth was the most important determinant in organizing polychaete assemblages in the study area. The Mississippi Canyon and the Central Transect (a non-canyon area) were found not contaminated by trace metals or Polynuclear Aromatic Hydrocarbons (PAHs) in sediments, although the highest PAHs concentration occurred at the head of the Canyon, MT1. The mean density was higher in the Mississippi Canyon (1668 N/m2) than in the Central Transect (979 N/m2), while the mean diversity in the Canyon (ES(100) = 26.9 ) was lower than the Central Transect (ES(100) = 33.1). Large amounts of terrigenous input from the Mississippi River to the Canyon could enhance polychaete density and accelerate competitive exclusion, and thus lead to lower diversity. The faunal composition was significantly different between the two transects, with higher species richness in the Mississippi Canyon (301 species). This could be attributed to structure complexity in the Mississippi Canyon. The distribution of feeding guilds was similar between two transects. The differences observed in polychaete assemblages between two transects may be largely due to high terrigenous sediment and organic matter input to the Mississippi Canyon by the Mississippi River.

Wang, Yuning

2004-12-01T23:59:59.000Z

110

Sediment transport in the Mississippi Canyon: the role of currents and storm events on optical variability  

E-Print Network (OSTI)

Two modes of sediment transport were found to exist in the Mississippi Canyon: the offshelf transport of material in intermediate nepheloid layers originating at depths of 50-175 m and the resuspension and transport of material within the canyon. Large- and small-particle intermediate nepheloid layers were consistently present in the canyon axis and were not observed on the slope to either side of the canyon. The temporal variability in currents, temperature, and particulate matter was measured at a station located at 300 m depth in the canyon axis during consecutive deployments in May-July and August-November 1998. Two moored current meters, one at 3.5 mab and one at 50 mab, recorded flow, while thermographs, a light-scattering sensor, and sediment traps gathered information about the characteristics of the flow and movement of particulate matter. Currents in the upper Mississippi Canyon were oscillatory, with alternating periods of up-canyon and down-canyon flow. Harmonic analysis revealed that the diurnal tidal signal was the dominant component of the flow. Currents were most intense at 3.5 mab. Mean current speed at this depth was approximately 8 cm s? during both deployments, reaching maximum speeds of over 50 cm s?. Current velocities generated sufficient shear stress to resuspend canyon floor sediments about 30% of the time during both deployments. During the second mooring deployment, Hurricane Georges passed 150 km NE of the study site. Near-bottom current velocities and temperature fluctuations were intensified. As the hurricane passed, maximum current speed reached 68 cm s? and a temperature decrease of approximately 7 degrees C occurred in less than 2 hours. Conditions were favorable for sediment resuspension approximately 50% of the time during the five days of hurricane influence. Further evidence for sediment resuspension was provided by similarities between canyon floor core samples and sediment trap collections.

Burden, Cheryl A

1999-01-01T23:59:59.000Z

111

Biglow Canyon Phase II Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Phase II Wind Farm Phase II Wind Farm Jump to: navigation, search Name Biglow Canyon Phase II Wind Farm Facility Biglow Canyon Phase II Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Portland General Electric Developer Orion Energy Group Energy Purchaser Portland General Electric Location Sherman County OR Coordinates 45.6375°, -120.605278° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":45.6375,"lon":-120.605278,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

112

Bechtel National, Inc. Engineers Constructors Oak Ridge Office  

Office of Legacy Management (LM)

389 389 Bechtel National, Inc. Engineers - Constructors Oak Ridge Office Jackson Plaza Tower 800 Oak Ridge Turnpike Oak Ridge, Tennessee Mail Address: P. O. Box 350, Oak Ridge. TN 37830 u.s. Department of Energy Oak Ridge Operations Post Office Box E Oak Ridge, TN 37830 ATTN: E. L. Keller, Director Technical Services Division SUBJECT: Bechtel Job No. 14501, FUSRAP Project DOE Contract No. DE-AC05-8l0R20722 Bayo Canyon Restrictive Covenants WBS No. 04D Dear Mr. Keller: Attached are the restrictive covenants on the Bayo Canyon parcels. These documents were prepared by the attorney for Professional Land Surveying, a Subcontractor to Bechtel who performed the required survey at Bayo Canyon. Please have your legal people review and comment on the subject convenants and return them to Bechtel for further action. Very truly yours, /12::..// tJ:Zf!-5-t:. Robert L. Rudolph Project Manager-FUSRAP

113

Fish Passage Assessment: Big Canyon Creek Watershed, Technical Report 2004.  

DOE Green Energy (OSTI)

This report presents the results of the fish passage assessment as outlined as part of the Protect and Restore the Big Canyon Creek Watershed project as detailed in the CY2003 Statement of Work (SOW). As part of the Northwest Power Planning Council's Columbia Basin Fish and Wildlife Program (FWP), this project is one of Bonneville Power Administration's (BPA) many efforts at off-site mitigation for damage to salmon and steelhead runs, their migration, and wildlife habitat caused by the construction and operation of federal hydroelectric dams on the Columbia River and its tributaries. The proposed restoration activities within the Big Canyon Creek watershed follow the watershed restoration approach mandated by the Fisheries and Watershed Program. Nez Perce Tribal Fisheries/Watershed Program vision focuses on protecting, restoring, and enhancing watersheds and treaty resources within the ceded territory of the Nez Perce Tribe under the Treaty of 1855 with the United States Federal Government. The program uses a holistic approach, which encompasses entire watersheds, ridge top to ridge top, emphasizing all cultural aspects. We strive toward maximizing historic ecosystem productive health, for the restoration of anadromous and resident fish populations. The Nez Perce Tribal Fisheries/Watershed Program (NPTFWP) sponsors the Protect and Restore the Big Canyon Creek Watershed project. The NPTFWP has the authority to allocate funds under the provisions set forth in their contract with BPA. In the state of Idaho vast numbers of relatively small obstructions, such as road culverts, block thousands of miles of habitat suitable for a variety of fish species. To date, most agencies and land managers have not had sufficient, quantifiable data to adequately address these barrier sites. The ultimate objective of this comprehensive inventory and assessment was to identify all barrier crossings within the watershed. The barriers were then prioritized according to the amount of habitat blocked at each site and the fish life history stages impacted. This assessment protocol will hopefully prove useful to other agencies and become a model for use in other watersheds.

Christian, Richard

2004-02-01T23:59:59.000Z

114

Fall Chinook Acclimation Project; Pittsburg Landing, Captain John Rapids, and Big Canyon, Annual Report 2002.  

DOE Green Energy (OSTI)

Fisheries co-managers of U.S. v Oregon supported and directed the construction and operation of acclimation and release facilities for Snake River fall Chinook from Lyons Ferry Hatchery at three sites above Lower Granite Dam. In 1996, Congress instructed the U.S. Army Corps of Engineers (USCOE) to construct, under the Lower Snake River Compensation Plan (LSRCP), final rearing and acclimation facilities for fall Chinook in the Snake River basin to complement their activities and efforts in compensating for fish lost due to construction of the lower Snake River dams. The Nez Perce Tribe (NPT) played a key role in securing funding and selecting acclimation sites, then assumed responsibility for operation and maintenance of the facilities. In 1997, Bonneville Power Administrative (BPA) was directed to fund operations and maintenance (O&M) for the facilities. Two acclimation facilities, Captain John Rapids and Pittsburg Landing, are located on the Snake River between Asotin, WA and Hells Canyon Dam and one facility, Big Canyon, is located on the Clearwater River at Peck. The Capt. John Rapids facility is a single pond while the Pittsburg Landing and Big Canyon sites consist of portable fish rearing tanks assembled and disassembled each year. Acclimation of 450,000 yearling smolts (150,000 each facility) begins in March and ends 6 weeks later. When available, an additional 2,400,000 fall Chinook sub-yearlings may be acclimated for 6 weeks, following the smolt release. The project goal is to increase the naturally spawning population of Snake River fall Chinook salmon upstream of Lower Granite Dam. This is a supplementation project; in that hatchery produced fish are acclimated and released into the natural spawning habitat for the purpose of returning a greater number of spawners to increase natural production. Only Snake River stock is used and production of juveniles occurs at Lyons Ferry Hatchery. This is a long-term project, targeted to work towards achieving delisting goals established by National Marine Fisheries Service (NMFS or NOAA Fisheries) and ultimately to provide fall Chinook adults through the Lower Snake River Compensation Plan program as mitigation for construction and operation of the four lower Snake River dams. Complete adult returns (all age classes) for all three acclimation facilities occurred in the year 2002. Progeny (which would then be natural origin fish) would be counted towards achieving Endangered Species Act delisting criteria. In 2002, a total of 2,877,437 fish weighing 47,347 pounds were released from the three acclimation facilities. The total includes 479,358 yearling fish weighing 33,930 pounds and 2,398,079 sub-yearling fish weighing 19,115 pounds. This is the largest number of fish ever released in one year from the acclimation facilities.

McLeod, Bruce

2003-01-01T23:59:59.000Z

115

Microsoft Word - canyon disposition rpt 2 01 05.doc  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Department of Energy Efforts to Department of Energy Efforts to Dispose of Hanford's Chemical Separation Facilities DOE/IG-0672 February 2005 -2- benefits of using the facility as a disposal site. Instead, the study focused on characterizing and performing technical analysis on the structural integrity of the facility. In studying the merits of the Initiative, the Department did not ensure that the cost study was sufficient in scope, and once completed, never reviewed the study to determine whether it was accurate and complete or adequately supported the preferred alternative. As a result of not thoroughly evaluating the feasibility of using canyon facilities for waste disposal, the Department may not realize savings ranging up to $500 million. This report highlights the importance of the Department's oversight of its contractors' activities to

116

RECALIBRATION OF H CANYON ONLINE SPECTROPHOTOMETER AT EXTENDED URANIUM CONCENTRATION  

SciTech Connect

The H Canyon online spectrophotometers are calibrated for measurement of the uranium and nitric acid concentrations of several tanks in the 2nd Uranium Cycle.[1] The spectrometers, flow cells, and prediction models are currently optimized for a process in which uranium concentrations are expected to range from 0-15 g/L and nitric acid concentrations from 0.05-6 M. However, an upcoming processing campaign will involve 'Super Kukla' material, which has a lower than usual enrichment of fissionable uranium. Total uranium concentrations will be higher, spanning approximately 0-30 g/L U, with no change in the nitric acid concentrations. The new processing conditions require the installation of new flow cells with shorter path lengths. As the process solutions have a higher uranium concentration, the shorter path length is required to decrease the absorptivity to values closer to the optimal range for the instrument. Also, new uranium and nitric acid prediction models are required to span the extended uranium concentration range. The models will be developed for the 17.5 and 15.4 tanks, for which nitric acid concentrations will not exceed 1 M. The restricted acid range compared to the original models is anticipated to reduce the measurement uncertainty for both uranium and nitric acid. The online spectrophotometers in H Canyon Second Uranium Cycle were modified to allow measurement of uranium and nitric acid for the Super Kukla processing campaign. The expected uranium concentrations, which are higher than those that have been recently processed, required new flow cells with one-third the optical path length of the existing cells. Also, new uranium and nitric acid calibrations were made. The estimated reading uncertainties (2{sigma}) for Tanks 15.4 and 17.5 are {approx}5% for uranium and {approx}25% for nitric acid.

Lascola, R

2008-10-29T23:59:59.000Z

117

Record of Decision - Klondike III/ Biglow Canyon Wind Integration Project - 10-25-06  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Klondike III/Biglow Canyon Wind Integration Project Klondike III/Biglow Canyon Wind Integration Project DECISION The Bonneville Power Administration (BPA) has decided to implement the Proposed Action identified in the Klondike III/Biglow Canyon Wind Integration Project Final Environmental Impact Statement (FEIS) (DOE/EIS-0374, September 2006). Under the Proposed Action, BPA will offer PPM Energy, Inc. (PPM) contract terms for interconnection of the proposed Klondike III Wind Project, located in Sherman County, Oregon, with the Federal Columbia River Transmission System (FCRTS). BPA will also offer Portland General Electric (PGE) 1 contract terms for interconnection of its proposed Biglow Canyon Wind Farm, also located in Sherman County, Oregon, with the FCRTS, as proposed in the FEIS. To interconnect these wind projects,

118

Recovery Act Begins Box Remediation Operations at F Canyon | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Recovery Act Begins Box Remediation Operations at F Canyon Recovery Act Begins Box Remediation Operations at F Canyon Recovery Act Begins Box Remediation Operations at F Canyon May 17, 2011 - 12:00pm Addthis Media Contacts Jim Giusti, DOE (803) 952-7697 james-r.giusti@srs.gov Paivi Nettamo, SRNS (803) 646-6075 paivi.nettamo@srs.gov AIKEN, S.C. - The F Canyon box remediation program, an American Recovery and Reinvestment Act project at Savannah River Site (SRS), has come online to process legacy transuranic (TRU) waste for off-site shipment and permanent disposal at the Waste Isolation Pilot Plant (WIPP), a geological repository in New Mexico. The $40-million facility will process approximately 330 boxes containing TRU waste with a radiological risk higher than seen in the rest of the Site's original 5,000-cubic-meter

119

On Line Spectrophotometric Measurement of Uranium and Nitrate in H Canyon  

SciTech Connect

This report describes the on-line instrumentation developed by the Analytical Development Section of Savannah River Technology Center in support of Highly Enriched Uranium Blend Down processing in H Canyon.

Lascola, R.J.

2002-10-15T23:59:59.000Z

120

Impulsively Started Flow in a Submarine Canyon: Comparison of Results from Laboratory and Numerical Models  

Science Conference Proceedings (OSTI)

Intercomparisons have been made of results from laboratory experiments and a numerical model for the flow in the vicinity of an idealized submarine canyon located along an otherwise continuous shelf. Motion in the rotating and continuously ...

Nicolas Prenne; J. William Lavelle; David C. Smith IV; Don L. Boyer

2001-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Mercury Vapor At Olowalu-Ukumehame Canyon Area (Thomas, 1986) | Open Energy  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » Mercury Vapor At Olowalu-Ukumehame Canyon Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Olowalu-Ukumehame Canyon Area (Thomas, 1986) Exploration Activity Details Location Olowalu-Ukumehame Canyon Area Exploration Technique Mercury Vapor Activity Date Usefulness could be useful with more improvements DOE-funding Unknown Notes Soil mercury concentration and radon emanometry surveys were conducted along the stream beds in both Olowalu and Ukumehame Canyons and on the coastal alluvial fans (Cox and Cuff, 1981a). The results of these surveys

122

Field Mapping At Olowalu-Ukumehame Canyon Area (Thomas, 1986) | Open Energy  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » Field Mapping At Olowalu-Ukumehame Canyon Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Field Mapping At Olowalu-Ukumehame Canyon Area (Thomas, 1986) Exploration Activity Details Location Olowalu-Ukumehame Canyon Area Exploration Technique Field Mapping Activity Date Usefulness not useful DOE-funding Unknown Notes Geologic mapping (Diller, 1982) in this area has identified several trachitic and alkalic dikes, plugs, and vents within the area bounded by the canyons (Fig. 21). The frequency distribution of those dikes in the two

123

EA-1863: Vegetation Management on the Glen Canyon-Pinnacle Peak  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

63: Vegetation Management on the Glen Canyon-Pinnacle Peak 63: Vegetation Management on the Glen Canyon-Pinnacle Peak Transmission Lines Spanning the Coconino National Forest, Coconino County, Arizona EA-1863: Vegetation Management on the Glen Canyon-Pinnacle Peak Transmission Lines Spanning the Coconino National Forest, Coconino County, Arizona Summary DOE's Western Area Power Administration is preparing this EA to evaluate the environmental impacts of updating the vegetation management and right-of-way maintenance program for Western's Glen Canyon to Pinnacle Peak 345-kV transmission lines, which cross the Coconino National Forest, Coconino County, Arizona. For more information on this EA, contact: Ms. Linette King at: lking@wapa.gov. Public Comment Opportunities No public comment opportunities available at this time.

124

Savannah River Site's H Canyon Begins 2012 with New and Continuing  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Site's H Canyon Begins 2012 with New and Site's H Canyon Begins 2012 with New and Continuing Missions - Transuranic waste remediation, new mission work are the focus of the nation's only active nuclear chemical separations facility in 2012 Savannah River Site's H Canyon Begins 2012 with New and Continuing Missions - Transuranic waste remediation, new mission work are the focus of the nation's only active nuclear chemical separations facility in 2012 January 1, 2012 - 12:00pm Addthis H Canyon, above, and HB-Line are scheduled to soon begin dissolving and purifying plutonium currently stored at the Savannah River Site to demonstrate the capability to produce oxide material that meets the Mixed Oxide Facility (MOX) feedstock specifications. The production process at MOX, which is now under construction, will eventually create fuel pellets for U.S. commercial reactor fuel assemblies.

125

EA-1863: Vegetation Management on the Glen Canyon-Pinnacle Peak  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3: Vegetation Management on the Glen Canyon-Pinnacle Peak 3: Vegetation Management on the Glen Canyon-Pinnacle Peak Transmission Lines Spanning the Coconino National Forest, Coconino County, Arizona EA-1863: Vegetation Management on the Glen Canyon-Pinnacle Peak Transmission Lines Spanning the Coconino National Forest, Coconino County, Arizona Summary DOE's Western Area Power Administration is preparing this EA to evaluate the environmental impacts of updating the vegetation management and right-of-way maintenance program for Western's Glen Canyon to Pinnacle Peak 345-kV transmission lines, which cross the Coconino National Forest, Coconino County, Arizona. For more information on this EA, contact: Ms. Linette King at: lking@wapa.gov. Public Comment Opportunities No public comment opportunities available at this time.

126

Micro-Earthquake At New York Canyon Geothermal Area (2011) | Open Energy  

Open Energy Info (EERE)

York Canyon Geothermal Area (2011) York Canyon Geothermal Area (2011) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Micro-Earthquake At New York Canyon Geothermal Area (2011) Exploration Activity Details Location New York Canyon Geothermal Area Exploration Technique Micro-Earthquake Activity Date 2011 Usefulness not indicated DOE-funding Unknown Exploration Basis Determine seismicity before and after reservoir stimulation for EGS Notes The overall goal is to gather high resolution seismicity data before, during and after stimulation activities at the EGS projects. This will include both surface and borehole deployments (as necessary in available boreholes) to provide high quality seismic data for improved processing and interpretation methodologies. This will allow the development and testing

127

Internal Tides and Mixing in a Submarine Canyon with Time-Varying Stratification  

Science Conference Proceedings (OSTI)

The time variability of the energetics and turbulent dissipation of internal tides in the upper Monterey Submarine Canyon (MSC) is examined with three moored profilers and five ADCP moorings spanning FebruaryApril 2009. Highly resolved time ...

Zhongxiang Zhao; Matthew H. Alford; Ren-Chieh Lien; Michael C. Gregg; Glenn S. Carter

2012-12-01T23:59:59.000Z

128

Fire modeling for Building 221-T - T Plant Canyon Deck and Railroad Tunnel  

Science Conference Proceedings (OSTI)

This report was prepared by Hughes Associates, Inc. to document the results of fire models for building 221-T Canyon Deck and Railroad Tunnel. Backup data is contained in document No. WHC-SD-CP-ANAL-010, Rev. 0.

Oar, D.L.

1994-09-29T23:59:59.000Z

129

Transport of a Power Plant Tracer Plume over Grand Canyon National Park  

Science Conference Proceedings (OSTI)

Meteorological and air-quality data, as well as surface tracer concentration values, were collected during 1990 to assess the impacts of Navajo Generating Station (NGS) emissions on Grand Canyon National Park (GCNP) air quality. These data have ...

Jun Chen; Robert Bornstein; Charles G. Lindsey

1999-08-01T23:59:59.000Z

130

MSHA issues Crandall Canyon investigation report, fines owners $1.6 million  

Science Conference Proceedings (OSTI)

The paper summarises the findings of the Mine Safety and Health Administration report (available at www.msha.gov) into the death of six people at the Crandall Canyon Mine on 6 August 2007.

NONE

2008-08-15T23:59:59.000Z

131

A Numerical Study of Flow and Pollutant Dispersion Characteristics in Urban Street Canyons  

Science Conference Proceedings (OSTI)

The flow and pollutant dispersion in urban street canyons are investigated using a two-dimensional numerical model with the k? turbulent closure scheme. It is shown that the flow field is characterized mainly by the number and intensity of ...

Jong-Jin Baik; Jae-Jin Kim

1999-11-01T23:59:59.000Z

132

Aspects of the Load Circulation at the Grand Canyon during the Fall Season  

Science Conference Proceedings (OSTI)

The atmosphere and circulation of air within, above, and around the Grand Canyon of the Colorado River was studied from an instrumented aircraft and from ground-based instruments in September and October 1984. Several patterns were identified. ...

L. P. Stearns

1987-10-01T23:59:59.000Z

133

A Numerical Study of Thermal Effects on Flow and Pollutant Dispersion in Urban Street Canyons  

Science Conference Proceedings (OSTI)

This study investigates thermal effects on the flow and pollutant dispersion in urban street canyons. A two-dimensional numerical model with a k? turbulent closure scheme is developed, and the heat transfer between the air and the building wall ...

Jae-Jin Kim; Jong-Jin Baik

1999-09-01T23:59:59.000Z

134

Sediment-Driven Downslope Flow in Submarine Canyons and Channels: Three-Dimensional Numerical Experiments  

Science Conference Proceedings (OSTI)

The role of submarine canyons and channels in sediment-driven downslope flow (sediment plumes) is examined, using a three-dimensional, rotational numerical model that couples the hydrodynamics and sediment transport. The model domain consists of ...

Jochen Kmpf; Hermann Fohrmann

2000-09-01T23:59:59.000Z

135

Cross-Shelf Exchange Driven by Oscillatory Barotropic Currents at an Idealized Coastal Canyon  

Science Conference Proceedings (OSTI)

Numerical simulations are used to study on-shelf transport of dense water by oscillatory barotropic currents incident upon an isolated coastal canyon. The physical system is a laboratory-scale annulus in which forcing is provided by an ...

D. B. Haidvogel

2005-06-01T23:59:59.000Z

136

LaboratoryNumerical Model Comparisons of Canyon Flows: A Parameter Study  

Science Conference Proceedings (OSTI)

An integrated set of laboratory and numerical-model experiments has been conducted to understand the development of residual circulation surrounding a coastal canyon and to explore further the degree to which laboratory experiments can provide ...

Don L. Boyer; Dale B. Haidvogel; Nicolas Prenne

2004-07-01T23:59:59.000Z

137

EIS-0480: Long-Term Experimental and Management Plan for the Operation of Glen Canyon Dam  

Energy.gov (U.S. Department of Energy (DOE))

Two agencies of the Department of the Interior, Bureau of Reclamation and National Park Service, are jointly preparing a Long-Term Experimental and Management Plan for the Glen Canyon Dam and an EIS for adoption of the Plan. The Glen Canyon Dam, on the Colorado River in northern, Arizona, generates hydroelectric power that is marketed by DOE's Western Area Power Administration, a cooperating agency.

138

Tertiary oxidation in Westwater Canyon member of Morrison formation  

SciTech Connect

Hematitic oxidation in the Westwater Canyon Sandstone Member of the Morrison Formation extends along the outcrop from the Pipeline fault northeast of Gallup, New Mexico, to the San Mateo fault north of Grants, New Mexico. The hematitic sandstone forms a broad lobe in the subsurface to a depth of 2,400 ft (730 m). The downdip edge of this sandstone arcs eastward from northeast Church Rock through Crownpoint, and southeastward to the west edge of the Ambrosia Lake district. The red sandstone is bordered on the downdip side by a band of limonitic oxidation, which interfingers with reduced sandstones basinward. The limonitic oxidation forms a relatively narrow band along the north and west sides of the hematitic lobe but expands progressively in an east and southeast direction. Weak limonitic oxidation, as indicated by the absence of pyrite and by a bleached to faint yellowish-gray color, appears to extend from the San Mateo fault eastward under Mount Taylor to the Rio Puerco of the east. The hematitic oxidation is epigenetic and is believed to be of early Miocene to late Pliocene age. The limonitic oxidation follows the present ground-water flow pattern and probably dates from late Pliocene to the Holocene. The oxidation patterns are important in uranium exploration because the hematitic area is essentially barren, whereas the limonitic areas contain ore deposits that are in the process of being destroyed by oxidation.

Saucier, A.E.

1980-01-01T23:59:59.000Z

139

Explaining the relationship between prehistoric agriculture and environment at Chaco Canyon, New Mexico  

E-Print Network (OSTI)

Chaco Canyon, the Pueblo settlement of New Mexico, represents one of the major cultural developments in the prehistoric Southwest. Between A.D. 900 and A.D. 1100 Chaco reached its peak of cultural florescence. This period was characterized by considerable building activities, appearance of Chaco outliers, and the construction of an extensive road system. After this period a dramatic decline in population and a cessation of building activity took place. Archaeologists call this phenomenon abandonment. In general, development and abandonment of Chaco Canyon coincided with changes in climatic conditions. Between A.D. 900 and A.D. 1100 there was a gradual increase in effective moisture and warmer temperature which proved favorable for agriculture there. With these optimal climatic conditions,development of Chaco Canyon witnessed a great increase in population. However, the Chaco Canyon region could not support a large population indefinitely because of its agricultural marginality. To solve this population-resource imbalance, Chacoan farmers of this period intensified their agricultural activities by constructing water control systems such as check dams, contour terraces, canals, and ditches. These measures worked for a while and the influence of Chaco Canyon was felt in the political, economic, and religious life of a broad geographic region. However, summer moisture began to decrease in the years between A.D. 1130 and A.D. 1180. This decrease became a full scale drought from A.D. 1157 to A.D. 1179 that seems to have severely affected agriculture and wild food resources available for the Chacoans. In addition, the Chacoan water control system designed to capture runoff probably proved to be inadequate as a buffering mechanism. Consequently, population at Chaco Canyon began to decrease and the region was abandoned after A.D. 1140. In an attempt at explaining the specific abandonment of Chaco Canyon, this thesis focuses on relationship between prehistoric agriculture and environment.

Gang, G-Young

1993-01-01T23:59:59.000Z

140

Advanced Oil Recovery Technologies for Improved Recovery from Slope Basin Clastic Reservoirs, Nash Draw Brushy Canyon Pool, Eddy County, NM  

Science Conference Proceedings (OSTI)

The Nash Draw Brushy Canyon Pool in Eddy County New Mexico was a cost-shared field demonstration project in the U.S. Department of Energy Class III Program. A major goal of the Class III Program was to stimulate the use of advanced technologies to increase ultimate recovery from slope-basin clastic reservoirs. Advanced characterization techniques were used at the Nash Draw Pool (NDP) project to develop reservoir management strategies for optimizing oil recovery from this Delaware reservoir. The objective of the project was to demonstrate that a development program, which was based on advanced reservoir management methods, could significantly improve oil recovery at the NDP. Initial goals were (1) to demonstrate that an advanced development drilling and pressure maintenance program can significantly improve oil recovery compared to existing technology applications and (2) to transfer these advanced methodologies to other oil and gas producers. Analysis, interpretation, and integration of recently acquired geological, geophysical, and engineering data revealed that the initial reservoir characterization was too simplistic to capture the critical features of this complex formation. Contrary to the initial characterization, a new reservoir description evolved that provided sufficient detail regarding the complexity of the Brushy Canyon interval at Nash Draw. This new reservoir description was used as a risk reduction tool to identify 'sweet spots' for a development drilling program as well as to evaluate pressure maintenance strategies. The reservoir characterization, geological modeling, 3-D seismic interpretation, and simulation studies have provided a detailed model of the Brushy Canyon zones. This model was used to predict the success of different reservoir management scenarios and to aid in determining the most favorable combination of targeted drilling, pressure maintenance, well stimulation, and well spacing to improve recovery from this reservoir. An Advanced Log Analysis technique developed from the NDP project has proven useful in defining additional productive zones and refining completion techniques. This program proved to be especially helpful in locating and evaluating potential recompletion intervals, which has resulted in low development costs with only small incremental increases in lifting costs. To develop additional reserves at lower costs, zones behind pipe in existing wells were evaluated using techniques developed for the Brushy Canyon interval. These techniques were used to complete uphole zones in thirteen of the NDP wells. A total of 14 recompletions were done: four during 1999, four during 2000, two during 2001, and four during 2002-2003. These workovers added reserves of 332,304 barrels of oil (BO) and 640,363 MCFG (thousand cubic feet of gas) at an overall weighted average development cost of $1.87 per BOE (barrel of oil equivalent). A pressure maintenance pilot project in a developed area of the field was not conducted because the pilot area was pressure depleted, and the reservoir in that area was found to be compartmentalized and discontinuous. Economic analyses and simulation studies indicated that immiscible injection of lean hydrocarbon gas for pressure maintenance was not warranted at the NDP and would need to be considered for implementation in similar fields very soon after production has started. Simulation studies suggested that the injection of miscible carbon dioxide (CO{sub 2}) could recover significant quantities of oil at the NDP, but a source of low-cost CO{sub 2} was not available in the area. Results from the project indicated that further development will be under playa lakes and potash areas that were beyond the regions covered by well control and are not accessible with vertical wells. These areas, covered by 3-D seismic surveys that were obtained as part of the project, were accessed with combinations of deviated/horizontal wells. Three directional/horizontal wells have been drilled and completed to develop reserves under surface-restricted areas and potash mines. The third

Mark B. Murphy

2005-09-30T23:59:59.000Z

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Installation of the Monitoring Site at the Los Alamos Canyon Low-Head Weir  

Science Conference Proceedings (OSTI)

The Cerro Grande fire of 2000 had an enormously adverse impact on and around Los Alamos National Laboratory (LANL). Immediately there were concerns about the potential for enhanced runoff/offsite transport of contaminant-laden sediments because of watershed damage. In response to this concern, the U.S. Army Corps of Engineers installed a low-head weir in Los Alamos Canyon near the White Rock ''Y.'' However, the occurrence of fractured basalt at the surface and ponding of runoff behind the weir enhance the possibility of downward migration of contaminants. Therefore, three boreholes were drilled on the south bank of the channel by LANL to provide a means of monitoring the impact of the Cerro Grande fire and of the weir on water quality beneath the canyon. The boreholes and associated instrumentation are referred to as the Los Alamos Weir Site (LAWS). The three boreholes include a vertical hole and two angled holes (one at approximately 45{sup o} and one at approximately 30{sup o}). Since the basalt is highly fractured, the holes would not stay open. Plans called for inserting flexible liners into all holes. However, using liners in such unstable ground was problematic and, in the angled holes, required deployment through scalloped or perforated polyvinyl chloride (PVC) shield. The vertical hole (LAWS-01), drilled to a total depth of 281.5 ft below ground surface (bgs), was completed as a 278-ft deep monitoring well with four screens: one targeting shallow perched water encountered at 80 ft, two in what may correspond to the upper perched zone at regional groundwater characterization well R-9i (1/4 mi. to the west), and one in what may correspond to the lower perched zone at R-9i. A Water FLUTe{trademark} system deployed in the well isolates the screened intervals; associated transducers and sampling ports permit monitoring head and water quality in the screened intervals. The second hole (LAWS-02), drilled at an angle of 43{sup o} from horizontal, is 156 ft long and bottoms at a depth of 106 ft bgs. The shallow perched water seen at LAWS-01 (at 80 ft) was not encountered. A scalloped PVC shield was installed to keep the hole open while permitting flexible liners to contact the borehole wall. It was initially instrumented with a color-reactive liner to locate water-producing fractures. That was later replaced by an absorbent liner to collect water from the vadose zone. The third hole (LAWS-03), drilled at an angle of 34{sup o} from horizontal, initially had a length of 136 ft and bottomed at a depth of 76 ft bgs. However, the PVC shield rotated during installation such that scallops were at the top and rock debris repeatedly fell in, preventing liner insertion. While pulling the scalloped PVC to replace it with a perforated PVC shield that did not require orientation, the scalloped PVC broke and only 85 ft was recovered. The hole was blocked at that position and could not be drilled out with the equipment available. Thus, LAWS-03 was completed at a length of 85 ft and a depth of 40 ft bgs. An absorbent liner was installed at the outset in preparation for the 2002 summer monsoon season. The entire monitoring site is enclosed inside a locked, 8-ft-high chainlink fence for security. The liners used in the angled boreholes carry electrical wire pairs to detect soil-moisture changes. Surface-water data are provided by stream gages above and below the weir site. Depth of ponding behind the weir is provided by a gage installed just behind the structure.

W.J.Stone; D.L.Newell

2002-08-01T23:59:59.000Z

142

Engines - Spark Ignition Engines  

NLE Websites -- All DOE Office Websites (Extended Search)

Spark Ignition Engines Spark Ignition Engines Thomas Wallner and omni engine Thomas Wallner and the omnivorous engine Background Today the United States import more than 60% of its crude oil and petroleum products. Transportation accounts for a major portion of these imports. Research in this field is focused on reducing the dependency on foreign oil by increasing the engine efficiency on the one hand and blending gasoline with renewable domestic fuels, such as ethanol, on the other. Argonne's Research The main focus of research is on evaluation of advanced combustion concepts and effects of fuel properties on engine efficiency, performance and emissions. The platforms used are a single-cylinder research engine as well as an automotive-size four-cylinder engine with direct fuel injection.

143

Flow Patterns at the Ends of a Street Canyon: Measurements from the Joint Urban 2003 Field Experiment  

Science Conference Proceedings (OSTI)

During the Joint Urban 2003 experiment held in Oklahoma City, Oklahoma, an eastwest-running street canyon was heavily instrumented with wind sensors. In this paper, the flow patterns at the street canyon ends are investigated by looking at sonic ...

Suhas U. Pol; Michael J. Brown

2008-05-01T23:59:59.000Z

144

Green Canyon Hot Springs Pool & Spa Low Temperature Geothermal Facility |  

Open Energy Info (EERE)

Green Canyon Hot Springs Pool & Spa Low Temperature Geothermal Facility Green Canyon Hot Springs Pool & Spa Low Temperature Geothermal Facility Facility Green Canyon Hot Springs Sector Geothermal energy Type Pool and Spa Location Newdale, Idaho Coordinates 43.8832463°, -111.6063483° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[]}

145

DOE - Office of Legacy Management -- White Canyon AEC Ore Buying Station -  

NLE Websites -- All DOE Office Websites (Extended Search)

White Canyon AEC Ore Buying Station White Canyon AEC Ore Buying Station - UT 04 FUSRAP Considered Sites Site: White Canyon AEC Ore Buying Station (UT.04) Designated Name: Alternate Name: Location: Evaluation Year: Site Operations: Site Disposition: Radioactive Materials Handled: Primary Radioactive Materials Handled: Radiological Survey(s): Site Status: The history of domestic uranium procurement under U.S. Atomic Energy Commission (AEC) contracts identifies a number of ore buying stations (sampling and storage sites) that were operated during the period late-1949 through the mid-1960s. During this period the AEC established ore-buying stations in new uranium producing areas where it appeared that ore production would be sufficient to support a uranium milling operation. The

146

Canyon dissolution of sand, slag, and crucible residues  

Science Conference Proceedings (OSTI)

An alternative to the FB-Line scrap recovery dissolver was desired for the dissolution of sand, slag, and crucible (SS{ampersand}C) residues from the plutonium reduction process due to the potential generation of hydrogen gas concentrations above the lower flammability limit. To address this concern, a flowsheet was developed for the F-Canyon dissolvers. The dissolvers are continually purged with nominally 33 SCFM of air; therefore the generation of flammable gas concentrations should not be a concern. Following removal of crucible fragments, small batches of the remaining sand fines or slag chunks containing less than approximately 350 grams of plutonium can be dissolved using the center insert in each of the four annular dissolver ports to address nuclear criticality safety concerns. Complete dissolution of the sand fines and slag chunks was achieved in laboratory experiments by heating between 75 and 85 degrees Celsius in a 9.3M nitric acid/0.013M (hydrogen) fluoride solution. Under these conditions, the sand and slag samples dissolved between 1 and 3 hours. Complete dissolution of plutonium and calcium fluorides in the slag required adjusting the dissolver solution to 7.5 wt% aluminum nitrate nonahydrate (ANN). Once ANN was added to a dissolver solution, further dissolution of any plutonium oxide (PuO2) in successive charges was not practical due to complexation of the fluoride by aluminum. During the laboratory experiments, well mixed solutions were necessary to achieve rapid dissolution rates. When agitation was not provided, sand fines dissolved very slowly. Measurement of the hydrogen gas generation rate during dissolution of slag samples was used to estimate the amount of metal in the chunks. Depending upon the yield of the reduction, the values ranged between approximately 1 (good yield) and 20% (poor yield). Aging of the slag will reduce the potential for hydrogen generation as calcium metal oxidizes over time. The potential for excessive corrosion in the dissolvers was evaluated using experimental data reported in the literature. Corrosion data at the exact flowsheet conditions were not available; however, the corrosion rate for 304L stainless steel (wrought material) corrosion coupons in 10M nitric acid/0.01M hydrofluoric acid at 95 degrees Celsius was reported as 21 mils per year. If the fluoride in the dissolver is complexed with aluminum, the corrosion rate will decrease to approximately 5 mils per year.

Rudisill, T.S.; Gray, J.H.; Karraker, D.G.; Chandler, G.T.

1997-12-01T23:59:59.000Z

147

The Influence of Canyon Winds on Flow Fields near Colorado's Front Range  

Science Conference Proceedings (OSTI)

A network of sodars was operated in the late summer and fall of 1993 to monitor the occurrence of nocturnal winds from a canyon in Colorado's Front Range near the Rocky Flats Plant and to determine the influence of those winds on the flow fields ...

J. C. Doran

1996-04-01T23:59:59.000Z

148

Functional design criteria, Project W-059, B Plant Canyon ventilation upgrade  

SciTech Connect

This document outlines the essential functions and requirements to be included in the design of the proposed B Plant canyon exhaust system upgrade. The project will provide a new exhaust air filter system and isolate the old filters from the airstream.

Roege, P.E.

1995-03-02T23:59:59.000Z

149

Observations of Thermally Driven Wind Jets at the Exit of Weber Canyon, Utah  

Science Conference Proceedings (OSTI)

Thermally driven valley-exit jets were investigated at Utahs Weber Canyon, a main tributary of the Great Salt Lake basin. An intensive measurement campaign during JulySeptember 2010 supplemented longer-term measurements to characterize the wind ...

Morgan F. Chrust; C. David Whiteman; Sebastian W. Hoch

2013-05-01T23:59:59.000Z

150

The Dependence of Canyon Winds on Surface Cooling and External Forcing in Colorado's Front Range  

Science Conference Proceedings (OSTI)

The atmospheric katabatic flow in the foothills of the Front Range of the Rocky Mountains has been monitored by a network of towers and sodars for several years as part of the ASCOT program. The dependence of the outflow from Coal Creek Canyon on ...

Richard L. Coulter; Paul Gudiksen

1995-06-01T23:59:59.000Z

151

Amphipods of the deep Mississippi Canyon, northern Gulf of Mexico: ecology and bioaccumulation of organic contaminants  

E-Print Network (OSTI)

In five summer cruises during the period 2000-2004, seventy-four box cores were collected from eleven locations from the Mississippi Canyon (480- 2750m, northern Gulf of Mexico), and an adjacent transect (336-2920) to understand the community structure and trophic function of amphipods and for measuring the bioaccumulation of polycyclic aromatic hydrocarbons, (PAHs). Amphipods were discovered to be an important component of the macrofauna of the Mississippi Canyon (40 % of the total faunal abundance). Seventy two species, belonging to nineteen families, were collected from the study area with 61 species from the canyon and only 38 species from the non-Canyon transect. The head of the canyon (480m) was dominated by dense mats (15,880 ind/m2) of a new amphipod (Ampelisca mississippiana). The logarithm of the amphipod abundance decreased linearly with depth. The species diversity (H`) exhibited a parabolic pattern with a maximum at 1100m. The differences in amphipod abundances and biodiversities were correlated with the variation in the amount of available organic matter. The depression in diversity in the canyon head is thought to be competitive exclusion resulting from the dominance by A.mississippiana, but the high species richness is presumed to be a function of the structural complexity of the canyon. Annual secondary production of A. mississippiana was 6.93 g dry wt m-2, based on size-frequency method and corresponding to an estimated univoltine generation from a regression model. The production/biomass ratio (P/B) was 3.11. Production of this magnitude is comparable to shallow marine ampeliscids but are high for the depauperate northern Gulf of Mexico. The effect of the organic contaminants and the bioavailability to the amphipods was determined through measuring the bioaccumulation of the PAHs. The distribution of PAHs in sediments was different from the distribution in the organisms suggesting preferential uptake/depuration or uptake from pore or bottom waters. The average bioaccumulation factor (4.36 2.55) and the biota sediment accumulation factor (0.240.13) for the total PAHs by the ampeliscids were within the range reported for other benthic invertebrates. The average bioaccumulation factors were highest for dibenzothiophenes (up to 132) and alkylated PAHs and lowest for parent high molecular weight PAHs.

Soliman, Yousria Soliman

2007-05-01T23:59:59.000Z

152

Aquatic macroinvertebrates and water quality of Sandia Canyon, Los Alamos National Laboratory, 1995  

Science Conference Proceedings (OSTI)

The Biology Team of ESH-20 (the Ecology Group) at Los Alamos National Laboratory (LANL) has collected samples from the stream within Sandia Canyon since the summer of 1990. These field studies measure water quality parameters and collect aquatic macroinvertebrates from sampling sites within the upper canyon stream. Reports by Bennett and Cross discuss previous aquatic studies in Sandia Canyon. This report updates and expands the previous findings. The Biology Team collected water quality data and aquatic macroinvertebrates monthly at three sampling stations within Sandia Canyon in 1995. The two upstream stations occur near a cattail (Typha latifolia) dominated marsh downstream from outfalls that discharge industrial and sanitary waste effluent into the stream, thereby maintaining year-round flow. The third station is approximately 1.5 miles downstream from the outfalls within a mixed conifer forest. All water chemistry parameters measured in Sandia Canyon during 1995 fell within acceptable State limits and scored in the {open_quotes}good{close_quotes} or {open_quotes}excellent{close_quotes} ranges when compared to an Environmental Quality Index. However, aquatic macroinvertebrates habitats have been degraded by widespread erosion, channelization, loss of wetlands due to deposition and stream lowering, scour, limited acceptable substrates, LANL releases and spills, and other stressors. Macroinvertebrate communities at all the stations had low diversities, low densities, and erratic numbers of individuals. These results indicate that although the stream possesses acceptable water chemistry, it has reduced biotic potential. The best developed aquatic community occurs at the sampling station with the best habitat and whose downstream location partially mitigates the effects of upstream impairments.

Cross, S.; Nottelman, H.

1997-01-01T23:59:59.000Z

153

Properties of the Wind Field within the Oklahoma City Park Avenue Street Canyon. Part I: Mean Flow and Turbulence Statistics  

Science Conference Proceedings (OSTI)

Velocity data were obtained from sonic anemometer measurements within an eastwest-running street canyon located in the urban core of Oklahoma City, Oklahoma, during the Joint Urban 2003 field campaign. These data were used to explore the ...

M. A. Nelson; E. R. Pardyjak; J. C. Klewicki; S. U. Pol; M. J. Brown

2007-12-01T23:59:59.000Z

154

Characterization of the Thermal Structure inside an Urban Canyon: Field Measurements and Validation of a Simple Model  

Science Conference Proceedings (OSTI)

The results of measurement campaigns are analyzed to investigate the thermal structure in an urban canyon and to validate a simplified model simulating the air and surface temperatures from surface energy budgets. Starting from measurements at ...

Lorenzo Giovannini; Dino Zardi; Massimiliano de Franceschi

2013-01-01T23:59:59.000Z

155

Observations of a Terrain-Forced Mesoscale Vortex and Canyon Drainage Flows along the Front Range of Colorado  

Science Conference Proceedings (OSTI)

Observations taken during the February 1991 Atmospheric Studies in Complex Terrain (ASCOT) Winter Validation Study are used to describe the wind field associated with a terrain-forced mesoscale vortex and thermally forced canyon drainage flows ...

David H. Levinson; Robert M. Banta

1995-07-01T23:59:59.000Z

156

Meteorological Processes Affecting the Transport of Emissions from the Navajo Generating Station to Grand Canyon National Park  

Science Conference Proceedings (OSTI)

During the 1990 Navajo Generating Station (NGS) Winter Visibility Study, a network of surface and upper-air meteorological measurement systems was operated in and around Grand Canyon National Park to investigate atmospheric processes in complex ...

Charles G. Lindsey; Jun Chen; Timothy S. Dye; L. Willard Richards; Donald L. Blumenthal

1999-08-01T23:59:59.000Z

157

A Large-Eddy Simulation Study of Thermal Effects on Turbulent Flow and Dispersion in and above a Street Canyon  

Science Conference Proceedings (OSTI)

Thermal effects on turbulent flow and dispersion in and above an idealized street canyon with a street aspect ratio of 1 are numerically investigated using the parallelized large-eddy simulation model (PALM). Each of upwind building wall, street ...

Seung-Bu Park; Jong-Jin Baik; Siegfried Raasch; Marcus Oliver Letzel

2012-05-01T23:59:59.000Z

158

Engineering Institute  

NLE Websites -- All DOE Office Websites (Extended Search)

Engineering Institute Engineering Institute Engineering Institute Engineering dynamics that include flight, vibration isolation for precision manufacturing, earthquake engineering, blast loading, signal processing, and experimental model analysis. Contact Leader, LANL Charles Farrar Email Leader, UCSD Michael Todd Email LANL Program Administrator Jutta Kayser (505) 663-5649 Email Collaboration for conducting mission-driven, multidisciplinary engineering research and recruiting, revitalization, and retention of current & future staff The Engineering Institute is a collaboration between LANL and the University of California at San Diego (UCSD) Jacobs School of Engineering, whose mission is to develop a comprehensive approach for conducting mission-driven, multidisciplinary engineering research

159

Microsoft Word - CX-Franklin-BadgerCanyonGrandview-RedMtnsDisconnectSwitch_WEB.docx  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8, 2012 8, 2012 REPLY TO ATTN OF: KEPR-4 SUBJECT: Environmental Clearance Memorandum Richard Heredia Project Manager - TEP-TPP-1 Proposed Action: Franklin-Badger Canyon and Grandview-Red Mountain switch replacements PP&A Project No.: 2,349 / 2,350 Categorical Exclusion Applied (from Subpart D, 10 C.F.R. Part 1021): B1.3 Routine maintenance Location: Benton County, Washington Proposed by: Bonneville Power Administration (BPA) Description of the Proposed Action: BPA proposes to replace disconnect switches and related equipment on the Franklin-Badger Canyon No.2 and Grandview-Red Mountain No.1 115- kilovolt transmission lines. The switch stands will be replaced in the same locations as the existing structures, and related load break equipment will be upgraded in-kind to existing. Both

160

Klondike III/Biglow Canyon Wind Integration Project; Record of Decision, October 25, 2006.  

DOE Green Energy (OSTI)

The Bonneville Power Administration (BPA) has decided to implement the Proposed Action identified in the Klondike III/Biglow Canyon Wind Integration Project Final Environmental Impact Statement (FEIS) (DOE/EIS-0374, September 2006). Under the Proposed Action, BPA will offer PPM Energy, Inc. (PPM) contract terms for interconnection of the proposed Klondike III Wind Project, located in Sherman County, Oregon, with the Federal Columbia River Transmission System (FCRTS). BPA will also offer Portland General Electric (PGE)1 contract terms for interconnection of its proposed Biglow Canyon Wind Farm, also located in Sherman County, Oregon, with the FCRTS, as proposed in the FEIS. To interconnect these wind projects, BPA will build and operate a 12-mile long, 230-kilovolt (kV) double-circuit transmission line between the wind projects and BPA's new 230-kV John Day Substation in Sherman County, Oregon. BPA will also expand its existing 500-kV John Day Substation.

United States. Bonneville Power Administration

2006-10-25T23:59:59.000Z

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Potential of breccia pipes in the Mohawk Canyon Area, Hualapai Indian Reservation, Arizona  

Science Conference Proceedings (OSTI)

The Hualapai Indian Reservation is on the southwestern corner of the Colorado Plateau in northern Arizona. Hundreds of solution-collapse breccia pipes crop out in the canyons and on the plateaus of northern Arizona. The pipes originated in the Mississippian Redwall Limestone and stoped their way upward through the upper Paleozoic strata, locally extending into the Triassic Moenkopi and Chinle Formations. The occurrence of high-grade U ore, associated with potentially economic concentrations of Cu, Ag, Pb, Zn, V, Co, and Ni in some of these pipes, has stimulated mining activity in northern Arizona despite the depressed market for most of these metals. Two breccia pipes, 241, and 242, have significant mineralized rock exposed on the Esplanade erosion surface; unfortunately, their economic potential is questionable because of their inaccessibility at the bottom of Mohawk Canyon. All warrant further exploration.

Wenrich, K.J.; Billingsley, G.H.; Van Gosen, B.S.

1990-09-21T23:59:59.000Z

162

Draft Environmental Impact Statement Klondike III/Biglow Canyon Wind Integration Project  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Summary S-1 Summary S-1 Summary In this Summary: * Purpose and Need for Action * Alternatives * Affected Environment * Impacts This summary covers the major points of the draft Environmental Impact Statement (EIS) prepared for the Klondike III/Biglow Canyon Wind Integration Project proposed by the Bonneville Power Administration (BPA). The project includes constructing a new double-circuit 230-kilovolt (kV) transmission line in northern Sherman County, Oregon. The new line would connect the Klondike III Wind Project and the Biglow Canyon Wind Farm to BPA's existing John Day 500-kV Substation. The project would also require expansion of BPA's existing John Day 500-kV Substation and a new 230-kV substation to integrate the two wind projects. As a federal agency, BPA is required by the National Environmental Policy Act

163

Annotated bibliography for the humpback chub (Gila cypha) with emphasis on the Grand Canyon population.  

DOE Green Energy (OSTI)

Glen Canyon Dam is a hydroelectric facility located on the Colorado River in Arizona that is operated by the U.S. Bureau of Reclamation (Reclamation) for multiple purposes including water storage, flood control, power generation, recreation, and enhancement of fish and wildlife. Glen Canyon Dam operations have been managed for the last several years to improve conditions for the humpback chub (Gila cypha) and other ecosystem components. An extensive amount of literature has been produced on the humpback chub. We developed this annotated bibliography to assist managers and researchers in the Grand Canyon as they perform assessments, refine management strategies, and develop new studies to examine the factors affecting humpback chub. The U.S. Geological Survey recently created a multispecies bibliography (including references on the humpback chub) entitled Bibliography of Native Colorado River Big Fishes (available at www.fort.usgs.gov/Products/data/COFishBib). That bibliography, while quite extensive and broader in scope than ours, is not annotated, and, therefore, does not provide any of the information in the original literature. In developing this annotated bibliography, we have attempted to assemble abstracts from relevant published literature. We present here abstracts taken unmodified from individual reports and articles except where noted. The bibliography spans references from 1976 to 2009 and is organized in five broad topical areas, including: (1) biology, (2) ecology, (3) impacts of dam operations, (4) other impacts, and (5) conservation and management, and includes twenty subcategories. Within each subcategory, we present abstracts alphabetically by author and chronologically by year. We present relevant articles not specific to either the humpback chub or Glen Canyon Dam, but cited in other included reports, under the Supporting Articles subcategory. We provide all citations in alphabetical order in Section 7.

Goulet, C. T.; LaGory, K. E.; Environmental Science Division

2009-10-05T23:59:59.000Z

164

DISSOLUTION OF FB-LINE METAL RESIDUES CONTAINING BERYLLIUM IN H-CANYON  

DOE Green Energy (OSTI)

Scrap materials containing plutonium (Pu) metal from FB-Line vaults are currently being dissolved in HB-Line for subsequent disposition through the H-Canyon facility. However, milestone and schedule commitments may require the dissolution of material containing Pu and beryllium (Be) metals in H-Canyon. To support this option, a flowsheet for dissolving Pu and Be metals in H-Canyon was demonstrated using a 4 M nitric acid (HNO{sub 3}) solution containing 0.3 M fluoride (F{sup -}). The F{sup -} was added as calcium fluoride (CaF{sub 2}). The dissolving solution also contained 2.5 g/L boron (B), a nuclear safety contingency for the H-Canyon dissolver, and 3.9 g/L iron (Fe) to represent the dissolution of carbon steel cans. The solution was heated to 90-95 C during the 8 h dissolution cycle. Dissolution of the Be metal appeared to begin as soon as the samples were added to the dissolver. Clear, colorless bubbles generated on the surface were observed and were attributed primarily to the generation of hydrogen (H{sub 2}) gas. The generation of nitrogen dioxide (NO{sub 2}) gas was also evident from the color of the solution. Essentially all of the Pu and Be dissolved during the first hour of the dissolution as the solution was heated to 90-95 C. The amount of residual solids collected following the dissolution was < 2% of the total metal charged to the dissolver. Examination of residual solids by scanning electron microscopy (SEM) showed that the largest dimension of the particles was less than 50 {micro}m with particles of smaller dimensions being more abundant. Energy dispersive spectra from spots on some of the particles showed the solids consisted of a small amount of undissolved material, corrosion products from the glassware, and dried salts from the dissolving solution.

Rudisill, T; Mark Crowder, M; Michael Bronikowski, M

2005-07-15T23:59:59.000Z

165

Steam Generator Tube Integrity Risk Assessment: Volume 2: Application to Diablo Canyon Power Plant  

Science Conference Proceedings (OSTI)

Damage to steam generator tubing can impair its ability to adequately perform the required safety functions in terms of structural stability and leakage. This report describes the Diablo Canyon Power Plant application of a method for calculating risk for severe accidents involving steam generator tube failure. The method helps utilities determine risks associated with application of alternate repair criteria and/or operation with degraded tubing.

2000-08-08T23:59:59.000Z

166

Dissolution of Plutonium Scrub Alloy and Anode Heel Materials in H-Canyon  

SciTech Connect

H-Canyon has a ''gap'' in dissolver operations during the last three months of FY03. One group of material to be processed during the gap is pre-existing scrub alloy material. There are 14 cans of material containing approximately 3.8 kilograms of plutonium. Of the 14 cans, it was anticipated that four cans contain salts, two cans contain anode heel materials, and eight cans contain scrub alloy buttons. H-Canyon desires to process the materials using a flowsheet similar to the SS and C (sand, slag and crucible) dissolution flowsheet used in F-Canyon. The materials will be loaded into carbon steel cans and then placed into aluminum metal charging bundles. Samples were sent to Savannah River Technology Center (SRTC) for characterization and flowsheet testing -- four MSE salts, two anode heels, and seven scrub alloy buttons. SRTC dissolved and characterized each of the samples. Two of them, originally thought to be MSE salts, were found to be graphite mold materials and were unsuitable for processing in H-Canyon. Characterization studies confirmed that the identification of the remaining items as MSE salts, scrub alloy buttons, and anode heel materials was correct. The MSE salts and anode heels solids are comprised primarily of plutonium, potassium, sodium and chloride. Both the MSE salts and anode heels left behind small amounts of residual solids. The scrub alloy buttons are comprised primarily of plutonium and aluminum. The solids dissolve readily with light, effervescent gas generation at the material surface and only trace amounts of NOx generation. Of the seven button samples, four dissolved completely. Two button samples contained small amounts of tantalum that did not dissolve. The last of the seven scrub alloy samples left a trace amount of residual plutonium solids. It is anticipated that the presence of undissolved fissile material is a function of where the sample was located relative to the button surface.

PIERCE, RA

2004-04-12T23:59:59.000Z

167

Evaluation of Zinc Addition During Cycle 9 at Diablo Canyon Unit 1  

Science Conference Proceedings (OSTI)

Laboratory studies have shown that zinc addition to primary coolant can mitigate primary water stress corrosion cracking (PWSCC) of Alloy 600 and reduce radiation fields in PWRs. This report documents experience with zinc addition during Cycle 9 at Diablo Canyon Power Plant Unit 1 (DCPP-1), operated by Pacific Gas & Electric. This project evaluated the effect of zinc addition on PWSCC initiation and propagation. It also examined the impact of zinc addition on radiation fields and fuel cladding deposition...

1999-10-27T23:59:59.000Z

168

Aquatic macroinvertebrates and water quality of Sandia Canyon, Los Alamos National Laboratory, November 1993--October 1994  

SciTech Connect

The Ecological Studies Team (EST) of ESH-20 at Los Alamos National Laboratory (LANL) has collected samples from the stream within Sandia Canyon since the summer of 1990. These field studies gather water quality measurements and collect aquatic macroinvertebrates from permanent sampling sites. Reports by Bennett (1994) and Cross (1994) discuss previous EST aquatic studies in Sandia Canyon. This report updates and expands those findings. EST collected water quality data and aquatic macroinvertebrates at five permanent stations within the canyon from November 1993 through October 1994. The two upstream stations are located below outfalls that discharge industrial and sanitary waste effluent into the stream, thereby maintaining year-round flow. Some water quality parameters are different at the first three stations from those expected of natural streams in the area, indicating degraded water quality due to effluent discharges. The aquatic habitat at the upper stations has also been degraded by sedimentation and channelization. The macroinvertebrate communities at these stations are characterized by low diversities and unstable communities. In contrast, the two downstream stations appear to be in a zone of recovery, where water quality parameters more closely resemble those found in natural streams of the area. The two lower stations have increased macroinvertebrate diversity and stable communities, further indications of downstream water quality improvement.

Cross, S.

1995-08-01T23:59:59.000Z

169

Operational Readiness Review Final Report For F-Canyon Restart. Phase 1  

SciTech Connect

An independent WSRC Operational Readiness Review was performed for the restart of Phase 1 processing in F-Canyon, Building 221-F. Readiness to restart the Second Plutonium Cycle process and solvent recovery was assessed. The ORR was conducted by an ORR board of ten members with the support of a subject matter expert. The chairman and four members were drawn from the Operational Safety Evaluation Department, ESH& QA Division; additional members were drawn from other WSRC divisions, independent of the F-Canyon operating division (NMPD). Based on the results of the readiness verification assessments performed according to the ORR plan and the validation of pre-restart corrective actions, the WSRC independent ORR Board has concluded that the facility has achieved the state of readiness committed to in the Restart Plan. Also, based on the scope of the ORR, it is the opinion of the board that F-Canyon Phase 1 processes can be restarted without undue risk to the safety of the public and onsite workers and without undue risk to the environment.

McFarlane, A.F.; Spangler, J.B.

1995-04-05T23:59:59.000Z

170

Environmenal analysis of the Bayo Canyon (TA-10) Site, Los Alamos, New Mexico  

SciTech Connect

The radiological survey of the old TA-10 site in Bayo Canyon found low levels of surface contamination in the vicinity of the firing sites and subsurface contamination in the old waste disposal area. The three alternatives proposed for the site are: (1) to take no action; (2) to restrict usage of the area of subsurface contamination to activities that cause no subsurface disturbance (minimal action); and (3) to remove the subsurface conamination to levels below the working criteria. Dose calculations indicate that doses from surface contamination for recreational users of the canyon, permanent residents, and construction workers and doses for workers involved in excavation of contaminated soil under the clean up alternative are only small percentages of applicable guidelines. No environmental impacts are associated with either the no-action or minimal action alternatives. The impact associated with the cleanup alternative is small, especially considering that the area already has been affected by the original TA-10 decommissioning action, but nevertheless, the preferred alternative is the minimal action alternative, where 0.6 hectare of land is restricted to surface activities. This leaves the rest of the canyon available for development with up to 400 homes. The restricted area can be used for a park, tennis courts, etc., and the /sup 90/Sr activity will decay to levels permitting unrestricted usage in about 160 y.

Ferenbaugh, R.W.; Buhl, T.E.; Stoker, A.K.; Hansen, W.R.

1982-05-01T23:59:59.000Z

171

Are software engineers true engineers?  

Science Conference Proceedings (OSTI)

Software engineering is an often used term to describe the activities, methods, and tools of large scale software development. There is an ongoing discussion whether Software Engineering can be considered as an engineering discipline. In ...

Claus Lewerentz; Heinrich Rust

2000-01-01T23:59:59.000Z

172

Shockwave Engine: Wave Disk Engine  

Science Conference Proceedings (OSTI)

Broad Funding Opportunity Announcement Project: MSU is developing a new engine for use in hybrid automobiles that could significantly reduce fuel waste and improve engine efficiency. In a traditional internal combustion engine, air and fuel are ignited, creating high-temperature and high-pressure gases which expand rapidly. This expansion of gases forces the engines pistons to pump and powers the car. MSUs engine has no pistons. It uses the combustion of air and fuel to build up pressure within the engine, generating a shockwave that blasts hot gas exhaust into the blades of the engines rotors causing them to turn, which generates electricity. MSUs redesigned engine would be the size of a cooking pot and contain fewer moving partsreducing the weight of the engine by 30%. It would also enable a vehicle that could use 60% of its fuel for propulsion.

None

2010-01-14T23:59:59.000Z

173

Stirling engines  

Science Conference Proceedings (OSTI)

The Stirling engine was invented by a Scottish clergyman in 1816, but fell into disuse with the coming of the diesel engine. Advances in materials science and the energy crisis have made a hot air engine economically attractive. Explanations are full and understandable. Includes coverage of the underlying thermodynamics and an interesting historical section. Topics include: Introduction to Stirling engine technology, Theoretical concepts--practical realities, Analysis, simulation and design, Practical aspects, Some alternative energy sources, Present research and development, Stirling engine literature.

Reader, G.T.; Hooper

1983-01-01T23:59:59.000Z

174

Internal structure of the Kern Canyon Fault, California: a deeply exhumed strike-slip fault  

E-Print Network (OSTI)

Deformation and mineral alteration adjacent to a 2 km long segment of the Kern Canyon fault near Lake Isabella, California are studied to characterize the internal structure of the fault zone and to understand the development of fault structure and constitution and the mechanical and chemical processes responsible for them. The 140 km long Kern Canyon fault (KCF) is a fault of 15 km right-lateral separation exhumed from seismogenic depth that cuts batholithic and metamorphic rocks of the southern Sierra Nevada. The fault consists of at least three distinct phases: an early phase of lower-greenschist-grade ductile shear with an S-C' phyllonite, a subsequent, dominant phase of brittle faulting characterized by a through-going zone of cataclastic rock, and a late stage of minor faulting along discontinuous, thin, hematitic gouge zones. The S-C' fabric and subsidiary fault-slip data indicate that both the phyllonitic and cataclastic zones are approximately vertical and strike-slip; slip lineations within the hematitic gouge suggest oblique-slip. The phyllonite zone trends N20-40E and accommodated ~175 m of separation. The cataclastic zone cuts the phyllonite, trends N21E, and consists of foliated and non-foliated cataclasites; it accommodates the majority of displacement along the fault. Abundant veins and fluid-assisted alteration in the rock surrounding the fault zone attest to the presence of fluids of evolving chemistry during both ductile and brittle faulting. Mass balance calculations indicate quartz loss during phyllonite faulting and imply that the fault system was open and experienced a negative change in volume during phyllonite faulting. Mesoscale and microscale fracture intensities decrease with log distance from the foliated cataclasites and approach a relatively low level at approximately 500 m. The internal structure of the Kern Canyon fault is similar to other large displacement faults in that it consists of a broad zone of fractured and altered rock and a narrow zone of intense cataclasis.

Neal, Leslie Ann

2002-01-01T23:59:59.000Z

175

Seismic stratigraphy and salt tectonics of the Alaminos Canyon area, Gulf of Mexico.  

E-Print Network (OSTI)

The Alaminos Canyon region is located at the change in the bathymetric trend between the slope and rise. Over 6,435 km of migrated seismic reflection profiles were analyzed to produce two structure and two isopach maps. Maps of the seafloor morphology, salt structure, and suprasalt sediments indicate the majority of the slope is covered by a shallow salt canopy. The salt structure map indicates that the Alaminos Canyon study area represents a transition from a semi-continuous salt sheet in the east to a less continuous salt sheet in the western margin. Salt lobe canopies are located within the eastern and western margins of the study area, while the central region represents a transition zone between the two lobate canopies. The sediment isochron maps show that the salt has played an important role in the sediment deposition and the formation of intraslope basins. The salt sheet interacted with slope sediment deposition by acting as a barrier to downslope sediment transport and by influencing the direction of mass transport. The uplift of the salt has formed topographic lows in which sediment is transported from the shelf beyond the slope. Within the study area, intraslope basins consist of remnants of submarine canyons blocked by diapiric uplift and closed depressions formed by subsidence in response to salt withdrawal. These intraslope basins have trapped thick deposits of sediment, thereby reducing the sediment transport beyond the slope region. Pleistocene sealevel fluctuations appear to be the dominant force in the depostional record. As the lowering of relative sealevel ended, the transport of sandy material decreased and hemipelagic sedimentation increased. Eustatic sealevel fluctuations during the Pleistocene led to cyclic seismic depostional sequences throughout the study area.

Mechler, Suzanne Marie

1994-01-01T23:59:59.000Z

176

SURVEY OF LOS ALAMOS AND PUEBLO CANYON FOR RADIOACTIVE CONTAMINATION AND RADIOASSAY TESTS RUN ON SEWER-WATER SAMPLES AND WATER AND SOIL SAMPLES TAKEN FROM LOS ALAMOS AND PUEBLO CANYONS  

SciTech Connect

Chemical sewers and sanitary lines draining the Tech Area, D. P. Site, CMR-12 Laundry, and surrounding residential areas flow into Pueblo and Los Alamos Canyon streams. In order to determine the extent and sources of radioactive contamination in these localities, fluid samples from each of the sewers, soil samples from each of the sewers, soil samples from the ground surrounding the sewer exits, and water and soil samples from selected spots in or near each of the two canyon streams were collected and analyzed for polonium and . plutonium. (W.D.M.)

Kingsley, W.H.; Fox, A.; Tribby, J.F.

1947-02-20T23:59:59.000Z

177

Toward Net Energy Buildings: Design, Construction, and Performance of the Grand Canyon House  

DOE Green Energy (OSTI)

The Grand Canyon house is a joint project of the DOE's National Renewable Energy Laboratory and the U.S. National Park Service and is part of the International Energy Agency Solar Heating and Cooling Programme Task 13 (Advanced Solar Low-Energy Buildings). Energy consumption of the house, designed using a whole-building low-energy approach, was reduced by 75% compared to an equivalent house built in accordance with American Building Officials Model Energy Code and the Home Energy Rating System criteria.

Balcomb, J. D.; Hancock, C. E.; Barker, G.

1999-06-23T23:59:59.000Z

178

B Plant canyon sample TK-21-1 analytical results for the final report  

Science Conference Proceedings (OSTI)

This document is the analytical laboratory report for the TK-21-1 sample collected from the B Plant Canyon on February 18, 1998. The sample was analyzed in accordance with the Sampling and Analysis Plan for B Plant Solutions (SAP) (Simmons, 1997) in support of the B Plant decommissioning project. Samples were analyzed to provide data both to describe the material which would remain in the tanks after the B Plant transition is complete and to determine Tank Farm compatibility. The analytical results are included in the data summary table (Table 1).

Steen, F.H.

1998-04-10T23:59:59.000Z

179

Optical engineering  

SciTech Connect

The Optical Engineering thrust area at Lawrence Livermore National Laboratory (LLNL) was created in the summer of 1996 with the following main objectives: (1) to foster and stimulate leading edge optical engineering research and efforts key to carrying out LLNL's mission and enabling major new programs; (2) to bring together LLNL's broad spectrum of high level optical engineering expertise to support its programs. Optical engineering has become a pervasive and key discipline, with applications across an extremely wide range of technologies, spanning the initial conception through the engineering refinements to enhance revolutionary application. It overlaps other technologies and LLNL engineering thrust areas.

Saito, T T

1998-01-01T23:59:59.000Z

180

Advanced Oil Recovery Technologies for Improved Recovery from Slope Basin Clastic Reservoirs, Nash Draw Brushy Canyon Pool, Eddy County, NM  

Science Conference Proceedings (OSTI)

Advanced reservoir characterization techniques are being used at the Nash Draw Brushy Canyon Pool project to develop reservoir management strategies for optimizing oil recovery from this Delaware reservoir. The reservoir characterization, geologic modeling, 3-D seismic interpretation, and simulation studies have provided a detailed model of the Brushy Canyon zones. This model was used to predict the success of different reservoir management scenarios and to aid in determining the most favorable combination of targeted drilling, pressure maintenance, well stimulation, and well spacing to improve recovery from this reservoir.

Murphy, M.B.

1999-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Engines - Compression-Ignition - Locomotive Engines - emissions...  

NLE Websites -- All DOE Office Websites (Extended Search)

Locomotive Engine Research Program Drives Down Train Emissions General Motors Electromotive Division locomotive engine EMD Engine Locomotive engine manufacturers face a unique...

182

Detection of Gas Hydrates in Garden Banks and Keathley Canyon from Seismic Data  

E-Print Network (OSTI)

Gas hydrate is a potential energy source that has recently been the subject of much academic and industrial research. The search for deep-water gas hydrate involves many challenges that are especially apparent in the northwestern Gulf of Mexico, where the sub-seafloor is a complex structure of shallow salt diapirs and sheets underlying heavily deformed shallow sediments and surrounding diverse minibasins. Here, we consider the effect these structural factors have on gas hydrate occurrence in Garden Banks and Keathley Canyon blocks of the Gulf of Mexico. This was accomplished by first mapping the salt and shallow deformation structures throughout the region using a 2D grid of seismic reflection data. In addition, major deep-rooted faults and shallow-rooted faults were mapped throughout the area. A shallow sediment deformation map was generated that defined areas of significant faulting. We then quantified the thermal impact of shallow salt to better estimate the gas hydrate stability zone (GHSZ) thickness. The predicted base of the GHSZ was compared to the seismic data, which showed evidence for bottom simulating reflectors and gas chimneys. These BSRs and gas chimneys were used to ground-truth the calculated depth of the base of GHSZ. Finally, the calculated GHSZ thickness was used to estimate the volume of the gas hydrate reservoir in the area after determining the most reasonable gas hydrate concentrations in sediments within the GHSZ. An estimate of 5.5 trillion cubic meters of pure hydrate methane in Garden Banks and Keathley Canyon was obtained.

Murad, Idris

2009-05-01T23:59:59.000Z

183

Source Characterization of the August 6, 2007 Crandall Canyon Mine Seismic Event in Central Utah  

SciTech Connect

On August 6, 2007 a local magnitude 3.9 seismic event occurred at 08:48:40 UTC in central Utah. The epicenter is within the boundaries of the Crandall Canyon coal mine (c.f. Pechmann et al., this volume). We performed a moment tensor analysis with complete, three-component seismic recordings from stations operated by the USGS, the University of Utah, and EarthScope. The analysis method inverts the seismic records to retrieve the full seismic moment tensor, which allows for interpretation of both shearing (e.g., earthquakes) and volume-changing (e.g., explosions and collapses) seismic events. The results show that most of the recorded seismic wave energy is consistent with an underground collapse in the mine. We contrast the waveforms and moment tensor results of the Crandall Canyon Mine seismic event to a similar sized tectonic earthquake about 200 km away near Tremonton, Utah, that occurred on September 1, 2007. Our study does not address the actual cause of the mine collapse.

Ford, S R; Dreger, D S; Walter, W R

2008-07-01T23:59:59.000Z

184

Carbon Steel and Magnesium Oxide Dissolution for H-Canyon Process Applications  

DOE Green Energy (OSTI)

H Area Operations is planning to process plutonium-contaminated uranium metal scrap in its efforts to de-inventory excess nuclear materials. The Savannah River Technology Center (SRTC) performed flowsheet development to support the decision to process the scrap in H-Canyon using 2M nitric acid (HNO3) / 0.025M potassium fluoride (KF) and 2 g/L boron. The scrap will be charged to the H-Canyon dissolver via a stainless steel charging bundle with a carbon steel end cap that must dissolve in an appropriate time frame. Experimental work was performed with a range of potential materials to be used to fabricate the bundle end cap. Testing was conducted with samples of metal plate, wire, cans, rods, and rivets to assess their dissolution characteristics in 2M HNO3/ 0.025M KF and 2 g/L boron. Experiments also measured the amount of hydrogen gas generated during carbon steel dissolution using the above dissolver solution. Each material type and its associated dissolution characteristic relate to specific bundle end cap designs being considered. Supplemental studies were conducted to evaluate the behavior and effect of magnesium oxide (MgO) sand on dissolution of uranium metal in 2M HNO3/ 0.025M KF and 2 g/L boron. The potential exists for a small quantity of MgO to be introduced into the dissolution flowsheet due to the use of MgO sand to extinguish uranium metal fires.

PIERCE, RA

2004-04-12T23:59:59.000Z

185

Restoring Anadromous Fish Habitat in Big Canyon Creek Watershed, 2004-2005 Annual Report.  

DOE Green Energy (OSTI)

The ''Restoring Anadromous Fish Habitat in the Big Canyon Creek Watershed'' is a multi-phase project to enhance steelhead trout in the Big Canyon Creek watershed by improving salmonid spawning and rearing habitat. Habitat is limited by extreme high runoff events, low summer flows, high water temperatures, poor instream cover, spawning gravel siltation, and sediment, nutrient and bacteria loading. Funded by the Bonneville Power Administration (BPA) as part of the Northwest Power Planning Council's Fish and Wildlife Program, the project assists in mitigating damage to steelhead runs caused by the Columbia River hydroelectric dams. The project is sponsored by the Nez Perce Soil and Water Conservation District. Target fish species include steelhead trout (Oncorhynchus mykiss). Steelhead trout within the Snake River Basin were listed in 1997 as threatened under the Endangered Species Act. Accomplishments for the contract period September 1, 2004 through October 31, 2005 include; 2.7 riparian miles treated, 3.0 wetland acres treated, 5,263.3 upland acres treated, 106.5 riparian acres treated, 76,285 general public reached, 3,000 students reached, 40 teachers reached, 18 maintenance plans completed, temperature data collected at 6 sites, 8 landowner applications received and processed, 14 land inventories completed, 58 habitat improvement project designs completed, 5 newsletters published, 6 habitat plans completed, 34 projects installed, 2 educational workshops, 6 displays, 1 television segment, 2 public service announcements, a noxious weed GIS coverage, and completion of NEPA, ESA, and cultural resources requirements.

Rasmussen, Lynn (Nez Perce Soil and Conservation District, Lewiston, ID)

2006-07-01T23:59:59.000Z

186

Radionuclide contaminant analysis of small mammels, plants and sediments within Mortandad Canyon, 1994  

SciTech Connect

Small mammals, plants and sediments were sampled at one upstream location (Site 1) and two downstream locations (Site 2 and Site 3) from the National Pollution Discharge Elimination System outfall {number_sign}051-051 in Mortandad Canyon, Los Alamos County, New Mexico. The purpose of the sampling was to identify radionuclides potentially present, to quantitatively estimate and compare the amount of radionuclide uptake at specific locations (Site 2 and Site 3) within Mortandad Canyon to an upstream site (Site 1), and to identify the primary mode (inhalation ingestion, or surface contact) of contamination to small mammals. Three composite samples of at least five animals per sample were collected at each site. Pelts and carcasses of each animal were separated and analyzed independently. In addition, three composite samples were also collected for plants and sediments at each site. Samples were analyzed for {sup 241}Am, {sup 90}Sr, {sup 238}Pu, {sup 239}Pu, and total U. With the exception of total U, all mean radionuclide concentrations in small mammal carcasses and sediments were significantly higher at Site 2 than Site 1 or Site 3. No differences were detected in the mean radionuclide concentration of plant samples between sites. However, some radionuclide concentrations found at all three sites were higher than regional background. No differences were found between mean carcass radionuclide concentrations and mean pelt radionuclide concentrations, indicating that the two primary modes of contamination may be equally occurring.

Bennett, K.; Biggs, J.; Fresquez, P.

1996-01-01T23:59:59.000Z

187

Numerical model to characterize the thermal comfort in new ecodistricts: methodology and validation through the canyon street case  

Science Conference Proceedings (OSTI)

In built-up areas, the urban structures affect the radiative and thermal environment. The numerical simulation models provide informations about urban thermal performance for many ranges of urban configurations. This paper presents a validation of a ... Keywords: CFD model, building heat transfers, coupling model, street canyon, thermo-radiative model

Khaled Athamena; Jean Francois Sini; Julien Guilhot; Jerome Vinet; Maeva Sabre; Jean-Michel Rosant

2011-01-01T23:59:59.000Z

188

Numerical model to characterize the thermal comfort in new eco-districts: methodology and validation through the canyon street case  

Science Conference Proceedings (OSTI)

In built-up areas, the urban structures affect the radiative and thermal environment. The numerical simulation models provide informations about urban thermal performance for many ranges of urban configurations. This paper presents a validation of a ... Keywords: CFD model, building heat transfers, coupling model, street canyon, thermo-radiative model

Khaled Athamena; Jean Francois Sini; Julien Guilhot; Jerome Vinet; Maeva Sabre; Jean-Michel Rosant

2011-01-01T23:59:59.000Z

189

Challenges When Predicting Reservoir Quality in the Subsalt K2/K2-North Field, Green Canyon, Gulf of Mexico  

E-Print Network (OSTI)

in the K2/ K2-North Field, Green Canyon, Gulf of Mexico, presents many challenges for planning primary for seismi- cally better-imaged deepwater reservoirs in the eastern Gulf of Mexico, we utilize well- log, we used depositional mod- els based on Gulf of Mexico shallow-seismic analogs of distributary channel

Greene, Todd J.

190

Engines - Spark Ignition Engines - Hydrogen Engines  

NLE Websites -- All DOE Office Websites (Extended Search)

large-scale hydrogen infrastructure by using the well-known and widely used internal combustion engine as the device that transforms the energy stored in hydrogen into motion. The...

191

Grande Ronde Model Watershed Project; Dark Canyon Riparian Exclosure, Completion Report 2002.  

DOE Green Energy (OSTI)

The Baker Field Office, Vale District Bureau of Land Management (BLM) submitted a project proposal for funding in 2002 through the Grande Ronde Model Watershed Program (GRMWP). The project consisted of constructing two riparian exclosures to prevent livestock grazing in the riparian areas of Dark Canyon and Meadow Creek. The BLM completed the NEPA documentation and supplied the fencing materials. Funding from BPA through the GRMWP was used to complete the construction of the two exclosures. This project was completed in the fall of 2002. The project area is located in Union County, Oregon on BLM managed land adjacent to Dark Canyon and Meadow Creek, T. 3. S., R. 35 E., Section 24 and 25. Section 24 is along Dark Canyon Creek and section 25 is along Meadow Creek. Approximately 0.4 miles of stream would be protected from grazing with the construction of the two exclosures. A two person crew was hired to construct a four-strand barbed wire fence. The fence enclosed the riparian area on both sides of each creek so that no grazing would occur within the riparian area on BLM managed land. Total fence length is approximately 1.25 miles. Materials consisted of metal fence posts, barbed wire, rockjacks, fence stays, and 2 x 4's. The fence was constructed in the fall of 2002. The riparian area is effectively excluded from livestock grazing at this time. The construction of the exclosures should enhance riparian vegetation, increase bank stability, and improve riparian and in-stream habitat by exclusion of livestock in the riparian areas. Monitoring will ensure that the exclosures continues to be effective. Annual monitoring will include photo-points and compliance checks during the grazing season by BLM personnel. The BLM will submit a monitoring report, which includes the results of the annual monitoring, to the GRMWP in years 2005 and 2007. The exclosures do cross the creeks so maintenance may be needed on occasion, especially after high flow events in the creeks. Material such as logs which are mobilized during high stream flows may damage the exclosures requiring maintenance to keep cattle from grazing in the riparian areas. The BLM spent approximately $4,000 on fencing materials and $1,375 on NEPA compliance. In addition, the estimated cost of the monitoring over five years is expected to be approximately $1,600. The $5,050 that the BLM received from the BPA for the project was used to hire two temporary employees to construct the exclosures.

Kuck, Todd

2003-03-01T23:59:59.000Z

192

Information engineering  

SciTech Connect

The Information Engineering thrust area develops information technology to support the programmatic needs of Lawrence Livermore National Laboratory`s Engineering Directorate. Progress in five programmatic areas are described in separate reports contained herein. These are entitled Three-dimensional Object Creation, Manipulation, and Transport, Zephyr:A Secure Internet-Based Process to Streamline Engineering Procurements, Subcarrier Multiplexing: Optical Network Demonstrations, Parallel Optical Interconnect Technology Demonstration, and Intelligent Automation Architecture.

Hunt, D.N.

1997-02-01T23:59:59.000Z

193

General Engineers  

U.S. Energy Information Administration (EIA) Indexed Site

General Engineers General Engineers The U.S. Energy Information Administration (EIA) within the Department of Energy has forged a world-class information program that stresses quality, teamwork, and employee growth. In support of our program, we offer a variety of profes- sional positions, including the General Engineer, whose work is associated with analytical studies and evaluation projects pertaining to the operations of the energy industry. Responsibilities: General Engineers perform or participate in one or more of the following important functions: * Design modeling systems to represent energy markets and the physical properties of energy industries * Conceive, initiate, monitor and/or conduct planning and evaluation projects and studies of continuing and future

194

Draft Environmental Impact Statement Klondike III/Biglow Canyon Wind Integration Project  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

generated from the proposed Klondike III Wind Project to the Federal Columbia River Transmission System. Orion Energy LLC has also asked BPA to interconnect 400 MW of electricity from its proposed Biglow Canyon Wind Farm, located north and east of the proposed Klondike III Wind Project. To interconnect these projects, BPA would need to build and operate a 230-kV double-circuit transmission line about 12 miles long, expand one substation and build one new substation. The wind projects would require wind turbines, substation(s), access roads, and other facilities. Two routes for the transmission line are being considered. Both begin at PPM's Klondike Schoolhouse Substation then travel north (Proposed Action) or north and westerly (Middle Alternative) to a new BPA

195

Uranium ore rolls in Westwater Canyon sandstone, San Juan Basin, New Mexico  

SciTech Connect

Recent relatively deep uranium-exploration drilling in the Nose Rock area, San Juan Basin, McKinley County, New Mexico, has resulted in the discovery of previously unrecognized uranium ore rolls in gray, unoxidized Westwater Canyon Sandstone of the Morrison Formation. Both the Nose Rock ores and the primary Ambrosia Lake uranium ores were emplaced during the Late Jurassic-Early Cretaceous erosional interval under the same geologic conditions by the same geochemical-cell process. The red, altered interior ground resulting from the geochemical-cell process has been re-reduced by the subsequent entry of reductants into the formation. The original roll form of the Ambrosia Lake orebodies has been obscured and modified by redistribution related to the present-day active redox interface interweaving with the Ambrosia Lake ores.

Clark, D.S.

1980-01-01T23:59:59.000Z

196

CHARACTERIZATION OF H CANYON CONDUCTIVITY METER INDICATIONS WITH ELEVATED URANIUM IN NITRIC ACID  

SciTech Connect

Solution conductivity data from the 1CU conductivity meter in H-Canyon shows that uranium concentration in the 0 to 30 gram per liter (g/L) range has no statistically significant effect on the calibration of free nitric acid measurement. Based on these results, no additional actions are needed on the 1CU Conductivity Meter prior to or during the processing of uranium solutions in the 0 to 30 g/L range. A model based only on free nitric acid concentration is shown to be appropriate for explaining the data. Data uncertainties for the free acid measurement of uranium-bearing solutions are 8.5% or less at 95% confidence. The analytical uncertainty for calibrating solutions is an order of magnitude smaller only when uranium is not present, allowing use of a more accurate analytical procedure. Literature work shows that at a free nitric acid level of 0.33 M, uranium concentration of 30 g/L and 25 C, solution conductivity is 96.4% of that of a uranium-free solution. The level of uncertainties in the literature data and its fitting equation do not justify calibration changes based on this small depression in solution conductivity. This work supports preparation of H-Canyon processing of Super Kukla fuel; however, the results will be applicable to the processing of any similar concentration uranium and nitric acid solution. Super Kukla fuel processing will increase the uranium concentration above the nominal zero to 10 g/L level, though not above 30 g/L. This work examined free nitric acid levels ranging from 0.18 to 0.52 molar. Temperature ranged from 27.9 to 28.3 C during conductivity testing. The data indicates that sequential order of measurement is not a significant factor. The conductivity meter was thus flushed effectively between measurements as desired.

Nash, C

2007-10-31T23:59:59.000Z

197

Early Channel Evolution in the Middle Permian Brushy Canyon Formation, West Texas, USA  

E-Print Network (OSTI)

Submarine channels are important conduits for sediment in deep marine environments, and understanding their formation is critical to modeling basin fill processes. Most models describing channel evolution focus on turbidity currents as the erosive and constructive force in channel initiation. However, slope failure and slumping can be significant drivers of channelization, particularly in upper slope and ramp environments. Determining the relative roles of slumping and erosion by turbidity currents can provide important insight into the timing of channelization and the geometries of subsequent deposits. Samples were collected from Guadalupe Mountains National Park from two primary localities at Salt Flat Bench (Figure 2). Three vertical sections were measured at both locations. A total of 16 samples were collected for petrographic analysis and X-ray fluorescence (XRF) imaging. Spectacular outcrop quality makes the Middle Permian Brushy Canyon Formation in Guadalupe Mountains National Park an ideal location for the study of early channel evolution. A detailed facies analysis of fine-grained channel deposits was conducted in the Upper Brushy Canyon Formation in the Salt Flat Bench outcrops. After channelization, an interval of relative condensation dominated by hemipelagic settling of organic matter and silt was followed by an interval of incomplete sediment bypass by turbidity currents. This sequence of events suggests that sea level was at a relative highstand at the time of channel inception, whereas channel inception by turbidity currents is expected during a lowstand. Slumping rather than erosion by turbidity currents is the most likely mechanism to have initiated a channel at the study area. There is no evidence for the existence for high energy currents until after the interval of condensation. However, the action of weak contour currents during early channel evolution is observed in outcrop and microtextural features. Early carbonate cementation of channel-lining silts may have stabilized the slump surface with respect to erosion by later turbidity currents.

Gunderson, Spencer

2011-08-01T23:59:59.000Z

198

Occurrence of gas hydrate in Oligocene Frio sand: Alaminos Canyon Block 818: Northern Gulf of Mexico  

SciTech Connect

A unique set of high-quality downhole shallow subsurface well log data combined with industry standard 3D seismic data from the Alaminos Canyon area has enabled the first detailed description of a concentrated gas hydrate accumulation within sand in the Gulf of Mexico. The gas hydrate occurs within very fine grained, immature volcaniclastic sands of the Oligocene Frio sand. Analysis of well data acquired from the Alaminos Canyon Block 818 No.1 ('Tigershark') well shows a total gas hydrate occurrence 13 m thick, with inferred gas hydrate saturation as high as 80% of sediment pore space. Average porosity in the reservoir is estimated from log data at approximately 42%. Permeability in the absence of gas hydrates, as revealed from the analysis of core samples retrieved from the well, ranges from 600 to 1500 millidarcies. The 3-D seismic data reveals a strong reflector consistent with significant increase in acoustic velocities that correlates with the top of the gas-hydrate-bearing sand. This reflector extends across an area of approximately 0.8 km{sup 2} and delineates the minimal probable extent of the gas hydrate accumulation. The base of the inferred gas-hydrate zone also correlates well with a very strong seismic reflector that indicates transition into units of significantly reduced acoustic velocity. Seismic inversion analyses indicate uniformly high gas-hydrate saturations throughout the region where the Frio sand exists within the gas hydrate stability zone. Numerical modeling of the potential production of natural gas from the interpreted accumulation indicates serious challenges for depressurization-based production in settings with strong potential pressure support from extensive underlying aquifers.

Boswell, R.D.; Shelander, D.; Lee, M.; Latham, T.; Collett, T.; Guerin, G.; Moridis, G.; Reagan, M.; Goldberg, D.

2009-07-15T23:59:59.000Z

199

REDUCTIONS WITHOUT REGRET: AVOIDING WRONG TURNS, ROACH MOTELS, AND BOX CANYONS  

SciTech Connect

This is the third of three papers (in addition to an introductory summary) aimed at providing a framework for evaluating future reductions or modifications of the U.S. nuclear force, first by considering previous instances in which nuclear-force capabilities were eliminated; second by looking forward into at least the foreseeable future at the features of global and regional deterrence (recognizing that new weapon systems currently projected will have expected lifetimes stretching beyond our ability to predict the future); and third by providing examples of past or possible undesirable outcomes in the shaping of the future nuclear force, as well as some closing thoughts for the future. In this paper, we provide one example each of our judgments on what constitutes a box canyon, a roach motel, and a wrong turn: ? Wrong Turn: The Reliable Replacement Warhead ? Roach Motel: SRAM T vs the B61 ? A Possible Box Canyon: A Low-Yield Version of the W76 SLBM Warhead Recognizing that new nuclear missions or weapons are not demanded by current circumstances ? a development path that yields future capabilities similar to those of today, which are adequate if not always ideal, and a broader national-security strategy that supports nonproliferation and arms control by reducing the role for, and numbers, of nuclear weapons ? we briefly consider alternate, less desirable futures, and their possible effect on the complex problem of regional deterrence. In this regard, we discuss the issues posed by, and possible responses to, three example regional deterrence challenges: in-country defensive use of nuclear weapons by an adversary; reassurance of U.S. allies with limited strategic depth threatened by an emergent nuclear power; and extraterritorial, non-strategic offensive use of nuclear weapons by an adversary in support of limited military objectives against a U.S. ally.

Swegle, J.; Tincher, D.

2013-09-11T23:59:59.000Z

200

Ex post power economic analysis of record of decision operational restrictions at Glen Canyon Dam.  

DOE Green Energy (OSTI)

On October 9, 1996, Bruce Babbitt, then-Secretary of the U.S. Department of the Interior signed the Record of Decision (ROD) on operating criteria for the Glen Canyon Dam (GCD). Criteria selected were based on the Modified Low Fluctuating Flow (MLFF) Alternative as described in the Operation of Glen Canyon Dam, Colorado River Storage Project, Arizona, Final Environmental Impact Statement (EIS) (Reclamation 1995). These restrictions reduced the operating flexibility of the hydroelectric power plant and therefore its economic value. The EIS provided impact information to support the ROD, including an analysis of operating criteria alternatives on power system economics. This ex post study reevaluates ROD power economic impacts and compares these results to the economic analysis performed prior (ex ante) to the ROD for the MLFF Alternative. On the basis of the methodology used in the ex ante analysis, anticipated annual economic impacts of the ROD were estimated to range from approximately $15.1 million to $44.2 million in terms of 1991 dollars ($1991). This ex post analysis incorporates historical events that took place between 1997 and 2005, including the evolution of power markets in the Western Electricity Coordinating Council as reflected in market prices for capacity and energy. Prompted by ROD operational restrictions, this analysis also incorporates a decision made by the Western Area Power Administration to modify commitments that it made to its customers. Simulated operations of GCD were based on the premise that hourly production patterns would maximize the economic value of the hydropower resource. On the basis of this assumption, it was estimated that economic impacts were on average $26.3 million in $1991, or $39 million in $2009.

Veselka, T. D.; Poch, L. A.; Palmer, C. S.; Loftin, S.; Osiek, B; Decision and Information Sciences; Western Area Power Administration

2010-07-31T23:59:59.000Z

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Web engineering  

Science Conference Proceedings (OSTI)

Web Engineering is the application of systematic, disciplined and quantifiable approaches to development, operation, and maintenance of Web-based applications. It is both a pro-active approach and a growing collection of theoretical and empirical research ... Keywords: development methodologies, taxonomy of Web applications, web Engineering, web application development, web-based information systems

Yogesh Deshpande; San Murugesan; Athula Ginige; Steve Hansen; Daniel Schwabe; Martin Gaedke; Bebo White

2002-10-01T23:59:59.000Z

202

CHEMICAL ENGINEERING AND MANUFACTURING CHEMICAL ENGINEERING  

E-Print Network (OSTI)

CHEMICAL ENGINEERING AND MANUFACTURING CHEMICAL ENGINEERING Objective Chemical Engineers of chemicals. This lesson introduces students to one component of chemical engineering: food processing, and a chemical engineer 2. How chemical engineers are involved in food production 3. That chemical engineers need

Provancher, William

203

NEWTON's Engineering References  

NLE Websites -- All DOE Office Websites (Extended Search)

engineering content for K-12 teachers. There are activities, lessons, and curriculum designed to introduce your students to engineering. ENGINEERING.com ENGINEERING.com...

204

College of Engineering Profile The College of Engineering at Colorado  

E-Print Network (OSTI)

College of Engineering Profile 2007-2008 The College of Engineering at Colorado State has a strong and Biological Engineering Civil and Environmental Engineering Electrical and Computer Engineering Mechanical Programs: Chemical and Biological Engineering Civil Engineering Computer Engineering Electrical Engineering

205

Harmonic engine  

Science Conference Proceedings (OSTI)

A high efficiency harmonic engine based on a resonantly reciprocating piston expander that extracts work from heat and pressurizes working fluid in a reciprocating piston compressor. The engine preferably includes harmonic oscillator valves capable of oscillating at a resonant frequency for controlling the flow of working fluid into and out of the expander, and also preferably includes a shunt line connecting an expansion chamber of the expander to a buffer chamber of the expander for minimizing pressure variations in the fluidic circuit of the engine. The engine is especially designed to operate with very high temperature input to the expander and very low temperature input to the compressor, to produce very high thermal conversion efficiency.

Bennett, Charles L. (Livermore, CA)

2009-10-20T23:59:59.000Z

206

Engineering Emergence  

Science Conference Proceedings (OSTI)

We explore various definitions and characteristics of emergence, how we might recognise and measure emergence, and how we might engineer emergent systems. We discuss the TUNA ("Theory Underpinning Nanotech Assemblers") project, which is investigating ...

Susan Stepney; Fiona A. C. Polack; Heather R. Turner

2006-08-01T23:59:59.000Z

207

Prognostic Prediction of Tracer Dispersion for the Diablo Canyon Experiments on August 31, September 2, and September 4, 1986  

DOE Green Energy (OSTI)

COAMPS/LODI simulations of the tracer experiments at Diablo Canyon on August 31, September 2, and September 4, 1986 had mixed results. Simulated tracer concentrations on August 31 differed significantly from the measured concentrations. The model transported SF{sub 6} too far south and did not predict transport of SF{sub 6} north along highway 101 or into See Canyon. Early in the day the model rapidly transported SF{sub 6} away from the release point while observations suggested the tracer stayed close to Diablo Canyon for 1-2 hours. For September 2, simulations agreed very well with the measurements. The model accurately predicted the change of wind direction from north northwest to east northeast at the release point. It also predicted the advection of tracer over Mot-r-0 Bay and through the Los Osos Valley toward San Luis Obispo in excellent agreement with the observations. On September 4, the calculated transport of SF{sub 6} from Diablo Canyon had defects similar to those on August 31, a trajectory too far south and limited intrusion of tracer north along highway 101. Conversely, simulations of the Freon release from Los Osos Cemetery on September 4 corresponded well with observations. Since the simulations used only global meteorological data and no local winds for input, even the limited success of COAMPS/LODI is a favorable result. COAMPS's inability to generate southerly winds through the highway 101 corridor on August 31 and September 4 is a symptom of its underestimate of the sea breeze. The weak sea breeze correlates with a small diurnal range of air temperature possibly associated with underestimates of surface solar heating and/or overestimates of surface wetness. Improvement of COAMPS/LODI simulations requires development of new data assimilation techniques to use the local surface and low altitude wind and temperature measurements. Also, quantitative methods are needed to assess the accuracy of the models.

Molenkamp, C.R.

1999-11-29T23:59:59.000Z

208

PETROPHYSICAL INVESTIGATION OF THE SECONDARY RECOVERY POTENTIAL IN THE CHERRY CANYON FORMATION NE LEA FIELD LEA COUNTY, NEW MEXICO  

Science Conference Proceedings (OSTI)

Read and Stevens has proposed the evaluation of the waterflood potential from the Cherry Canyon formation in the NE Lea Field in lea County, New Mexico. Much of the development in this area is approaching primary recovery limitations; additional recovery of remaining oil reserves by waterflood needs to be evaluated. The Cherry Canyon formation is composed of fine grained sandstone, containing clay material which results in high water saturation, and also has the tendency to swell and reduce reservoir permeability--the ability of fluid to flow through the rock pores and fractures. There are also abundant organic materials that interfere with obtaining reliable well logs. These complications have limited oil in place calculations and identification of net pay zones, presenting a challenge to the planned waterflood. Core analysis of the Cherry Canyon should improve the understanding of existing well logs and possibly indicate secondary recovery measures, such as waterflood, to enhance field recovery. Lacking truly representative core to provide accurate analyses, Read and Stevens will obtain and preserve fresh core. The consulting firm of T. Scott Hickman and Associates will then collaborate on special core analyses and obtain additional well logs for a more detailed analysis of reservoir properties. The log interpretation will be compared to the core analysis results, and the entire collected data set will be used to assess the potential and economic viability of successfully waterflooding the identified oil zones. Successful results from the project will improve accuracy of log interpretation and establish a methodology for evaluating secondary recovery by waterflood.

T. Scott Hickman

2002-06-01T23:59:59.000Z

209

Klondike III/Biglow Canyon Wind Integration Project; Final Environmental Impact Statement, September 2006.  

DOE Green Energy (OSTI)

BPA has been asked by PPM Energy, Inc. to interconnect 300 megawatts (MW) of electricity generated from the proposed Klondike III Wind Project to the Federal Columbia River Transmission System. Orion Energy LLC has also asked BPA to interconnect 400 MW of electricity from its proposed Biglow Canyon Wind Farm, located north and east of the proposed Klondike III Wind Project. (Portland General Electric recently bought the rights to develop the proposed Biglow Canyon Wind Farm from Orion Energy, LLC.) Both wind projects received Site Certificates from the Oregon Energy Facility Siting Council on June 30, 2006. To interconnect these projects, BPA would need to build and operate a 230-kV double-circuit transmission line about 12 miles long, expand one substation and build one new substation. The wind projects would require wind turbines, substation(s), access roads, and other facilities. Two routes for the transmission line are being considered. Both begin at PPM's Klondike Schoolhouse Substation then travel north (Proposed Action) or north and westerly (Middle Alternative) to a new BPA 230-kV substation next to BPA's existing John Day 500-kV Substation. BPA is also considering a No Action Alternative in which BPA would not build the transmission line and would not interconnect the wind projects. The proposed BPA and wind projects would be located on private land, mainly used for agriculture. If BPA decides to interconnect the wind projects, construction of the BPA transmission line and substation(s) could commence as early as the winter of 2006-07. Both wind projects would operate for much of each year for at least 20 years. The proposed projects would generally create no or low impacts. Wildlife resources and local visual resources are the only resources to receive an impact rating other than ''none'' or ''low''. The low to moderate impacts to wildlife are from the expected bird and bat mortality and the cumulative impact of this project on wildlife when combined with other proposed wind projects in the region. The low to high impacts to visual resources reflect the effect that the transmission line and the turbine strings from both wind projects would have on viewers in the local area, but this impact diminishes with distance from the project.

United States. Bonneville Power Administration

2006-09-01T23:59:59.000Z

210

COMPUTER ENGINEERING EECS Department  

E-Print Network (OSTI)

COMPUTER ENGINEERING EECS Department The Electrical Engineering and Computer Science (EECS) Department at WSU offers undergraduate degrees in electrical engineering, computer engineering and computer science. The EECS Department offers Master of Science degrees in computer science, electrical engineering

211

SAVANNAH RIVER SITE'S H-CANYON FACILITY: RECOVERY AND DOWN BLEND URANIUM FOR BENEFICIAL USE  

SciTech Connect

For over fifty years, the H Canyon facility at the Savannah River Site (SRS) has performed remotely operated radiochemical separations of irradiated targets to produce materials for national defense. Although the materials production mission has ended, the facility continues to play an important role in the stabilization and safe disposition of proliferable nuclear materials. As part of the US HEU Disposition Program, SRS has been down blending off-specification (off-spec) HEU to produce LEU since 2003. Off-spec HEU contains fission products not amenable to meeting the American Society for Testing and Material (ASTM) commercial fuel standards prior to purification. This down blended HEU material produced 301 MT of ~5% enriched LEU which has been fabricated into light water reactor fuel being utilized in Tennessee Valley Authority (TVA) reactors in Tennessee and Alabama producing economic power. There is still in excess of ~10 MT of off-spec HEU throughout the DOE complex or future foreign and domestic research reactor returns that could be recovered and down blended for beneficial use as either ~5% enriched LEU, or for use in subsequent LEU reactors requiring ~19.75% enriched LEU fuel.

Magoulas, V.

2013-05-27T23:59:59.000Z

212

Flowsheet modifications for dissolution of sand, slag, and crucible residues in the F-canyon dissolvers  

Science Conference Proceedings (OSTI)

An initial flowsheet for the dissolution of sand, slag, and crucible (SS{ampersand}C) was developed for the F- Canyon dissolvers as an alternative to dissolution in FB-Line. In that flowsheet, the sand fines were separated from the slag chunks and crucible fragments. Those two SS{ampersand}C streams were packaged separately in mild-steel cans for dissolution in the 6.4D dissolver. Nuclear safety constraints limited the dissolver charge to approximately 350 grams of plutonium in two of the three wells of the dissolver insert and required 0.23M (molar) boron as a soluble neutron poison in the 9.3M nitric acid/0.013M fluoride dissolver solution. During the first dissolution of SS{ampersand}C fines, it became apparent that a significant amount of the plutonium charged to the 6.4D dissolver did not dissolve in the time predicted by previous laboratory experiments. The extended dissolution time was attributed to fluoride complexation by boron. An extensive research and development (R{ampersand}D) program was initiated to investigate the dissolution chemistry and the physical configuration of the dissolver insert to understand what flowsheet modifications were needed to achieve a viable dissolution process.

Rudisill, T.S.; Karraker, D.G.; Graham, F.R.

1997-12-01T23:59:59.000Z

213

Electromagnetic (EM-60) survey in the Panther Canyon Area, Grass Valley, Nevada  

DOE Green Energy (OSTI)

Eight frequency domain electromagnetic soundings were measured over the Panther Canyon thermal anomaly in Grass Valley, Nevada. The data were collected with Lawrence Berkeley Laboratory's large moment horizontal loop system (EM-60). At the transmitter site located near the center of the thermal anomaly, square wave currents of up to 70 A were impressed into a fourturn 50 m radius coil at frequencies from 0.033 to 500 Hz. At the eight receiver sites, 0.5 to 1.5 km from the loop, magnetic fields were detected with a three-component SQUID magnetometer and vertical and radial magnetic field spectra were calculated. Data were interpreted with a computer program which fit filled spectra and associated ellipse polarization data to one-dimensional resistivity models and results were compared to interpretations from earlier dipole-dipole resistivity measurements. Comparison of these interpretations indicates fairly close agreement between the two, with both models clearly indicating the presence and dimensions of the conductivity anomaly associated with the thermal zone. Although the dc data was better able to resolve the high resistivity bedrock, the EM-data were able to resolve all major features without distortion at shorter transmitter receiver separations and in about one-third of the field time.

Wilt, M.; Goldstein, N.; Stark, M.; Haught, R.

1980-05-01T23:59:59.000Z

214

Treating high pressure zones in one trip in Canyon Reef area of Texas  

Science Conference Proceedings (OSTI)

In the Canyon Reef area near Snyder, Texas, Chevron U.S.A. Inc. is employing ratchet operated, packer type retrievable bridge plugs which have allowed operators to test, treat, or squeeze high pressure zones over a 35-day period on a single trip of the workstring. More zones could have been treated if necessary. The bridge plug was moved and set 31 times while treating the zones. Elapsed time is shown in days starting with T-date being the day tools were first run in for the treatment. The job was run with an average treating pressure of 1,000 psi, and a differential pressure of 2,500 psi that alternated from above the bridge plug to below and back each time the plug was moved to a new zone. The bridge plug used for the job seals by the action of a patented ratcheting mechanism which requires relatively light weight to set. Design of the ratchet enables the sealing elements to hold a seal against the casing wall while the hold-down slips are being set.

Cooley, G.; Mccowen, D.; Fore, M.

1984-03-01T23:59:59.000Z

215

Brookhaven Women Engineers' Network  

NLE Websites -- All DOE Office Websites (Extended Search)

Home | Mission | Other links BWEN Brookhaven Women Engineers' Network BNLlogo Brookhaven Women Engineers' Network Network for professionals in engineering, computing and...

216

Meta search engine.  

E-Print Network (OSTI)

??Meta search engines allow multiple engine searches to minimize biased information and improve the quality of the results it generates. However, existing meta engine applications (more)

Chan, Kwok-Pun

2007-01-01T23:59:59.000Z

217

EXPERIMENTAL STUDY TO EVALUATE CORROSION OF THE F-CANYON DISSOLVER DURING THEUNIRRADIATED MARK-42 CAMPAIGN  

DOE Green Energy (OSTI)

Unirradiated Mark 42 fuel tubes are to be dissolved in an upcoming campaign in F-canyon. Savannah River Technology Center (SRTC)/Chemical & Hydrogen Technology Section (CHTS) identified a flow sheet for the dissolution of these Mark 42 fuel tubes which required a more aggressive dissolver solution than previously required for irradiated Mark 42 fuel tubes. Subsequently, SRTC/MTS was requested to develop and perform a corrosion testing program to assess the impact of new flow sheets on corrosion of the dissolver wall. The two primary variables evaluated were the fluoride and aluminum concentrations of the dissolver solution. Fluoride was added as Calcium Fluoride (CaF{sub 2}) while the aluminum was added either as metallic aluminum, which was subsequently dissolved, or as the chemical aluminum nitrate (Al(NO{sub 3}){sub 3}). The dissolved aluminum metal was used to simulate the dissolution of the aluminum from the Mark 42 cladding and fuel matrix. Solution composition for the corrosion tests bracketed the flow sheet for the Mark 42. Corrosion rates of AISI Type 304 stainless steel coupons, both welded and non-welded coupons, were calculated from measured weight losses and post-test concentrations of soluble Fe, Cr and Ni. The corrosion rates, which ranged between 2.7 and 32.5 mpy, were calculated from both the one day and the one week weight losses. These corrosion rates indicated a relatively mild corrosion on the dissolver vessel. The welded coupons consistently had a higher corrosion rate than the non-welded coupons. The difference between the two decreased as the solution aggressiveness decreased. In these test solutions, aggressiveness corresponded with the fluoride concentration. Based on the results of this study, any corrosion occurring during the Mark 42 Campaign is not expected to have a deleterious effect on the dissolver vessel.

Mickalonis, J; Kerry Dunn, K

1999-08-01T23:59:59.000Z

218

Financial analysis of experimental releases conducted at Glen Canyon Dam during water year 2011  

DOE Green Energy (OSTI)

This report examines the financial implications of experimental flows conducted at the Glen Canyon Dam (GCD) in water year 2011. It is the third report in a series examining financial implications of experimental flows conducted since the Record of Decision (ROD) was adopted in February 1997 (Reclamation 1996). A report released in January 2011 examined water years 1997 to 2005 (Veselka et al. 2011), and a report released in August 2011 examined water years 2006 to 2010 (Poch et al. 2011). An experimental release may have either a positive or negative impact on the financial value of energy production. This study estimates the financial costs of experimental releases, identifies the main factors that contribute to these costs, and compares the interdependencies among these factors. An integrated set of tools was used to compute the financial impacts of the experimental releases by simulating the operation of the GCD under two scenarios, namely, (1) a baseline scenario that assumes both that operations comply with the ROD operating criteria and the experimental releases that actually took place during the study period, and (2) a 'without experiments' scenario that is identical to the baseline scenario of operations that comply with the GCD ROD, except it assumes that experimental releases did not occur. The Generation and Transmission Maximization (GTMax) model was the main simulation tool used to dispatch GCD and other hydropower plants that comprise the Salt Lake City Area Integrated Projects (SLCA/IP). Extensive data sets and historical information on SLCA/IP powerplant characteristics, hydrologic conditions, and Western Area Power Administration's (Western's) power purchase prices were used for the simulation. In addition to estimating the financial impact of experimental releases, the GTMax model was also used to gain insights into the interplay among ROD operating criteria, exceptions that were made to criteria to accommodate the experimental releases, and Western operating practices. Experimental releases conducted in water year 2011 resulted only in financial costs; the total cost of all experimental releases was about $622,000.

Poch, L. A.; Veselka, T. D.; Palmer, C. S.; Loftin, S.; Osiek, B. (Decision and Information Sciences); (Western Area Power Administration)

2012-07-16T23:59:59.000Z

219

Engineered Fire Safety Group  

Science Conference Proceedings (OSTI)

Engineered Fire Safety Group. Welcome. ... Employment/Research Opportunities. Contact. Jason Averill, Leader. Engineered Fire Safety Group. ...

2012-06-05T23:59:59.000Z

220

Engines - Spark Ignition Engines - Direct Injection - Omnivorous Engine  

NLE Websites -- All DOE Office Websites (Extended Search)

Direct Injection, Spark-Ignited Engines Direct Injection, Spark-Ignited Engines Omnivorous Engine Omnivorous Engine Setup Omnivorous Engine Setup New engine technology has made possible engines that will operate on a wide variety of fuel inputs, from gasoline to naptha to ethanol to methanol, without driver intervention. Although flexible fuel vehicles have been produced in the millions, their engines have always been optimized for gasoline operation while accepting significant performance and efficiency degradations when using the alternative fuel. This project seeks to combine in-cylinder measurement technology, and advanced controls to optimize spark timing, the quantity and timing of injected fuel, to produce an "omnivorous engine"--one that will be able to run on any liquid spark ignition fuel with optimal efficiency and low

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Dept. of Mechanical Engineering 1500 Engineering Dr.  

E-Print Network (OSTI)

of Diesel Engine, Exhaust System, Engine Emissions and Aftertreatment Device Models," SAE Paper 2005 Engine, Emissions, and Exhaust Aftertreatment System Level Model to Simulate Diesel Particulate Filter Diesel Engine, Emissions, and Exhaust Aftertreatment System Level Model," SAE 2009-01-1511, SAE

Sheridan, Jennifer

222

CHEMICAL ENGINEERING SCHOOL OF ENGINEERING & APPLIED SCIENCE  

E-Print Network (OSTI)

30 CHEMICAL ENGINEERING SCHOOL OF ENGINEERING & APPLIED SCIENCE MIAMI UNIVERSITY 2005-2006 The program leads to the degree, Bachelor of Science in Applied Science, with a major in Chemical Engineering The chemical engineering students learn to apply the concepts of chemistry, biochemistry and biological science

Dollar, Anna

223

Effects of hydropower operations on recreational use and nonuse values at Glen Canyon and Flaming Gorge Dams  

DOE Green Energy (OSTI)

Increases in streamflows are generally positively related to the use values of angling and white-water boating, and constant flows tend to increase the use values more than fluctuating flows. In most instances, however, increases in streamflows beyond some threshold level cause the use values to decrease. Expenditures related to angling and white-water boating account for about $24 million of activity in the local economy around Glen Canyon Dam and $24.8 million in the local economy around flaming Gorge Dam. The range of operational scenarios being considered in the Western Area Power Administration`s Electric Power Marketing Environmental Impact Statement, when use rates are held constant, could change the combined use value of angling and white-water boating below Glen Canyon Dam, increasing it by as much as 50%, depending on prevailing hydrological conditions. Changes in the combined use value below Flaming Gorge Dam could range from a decrease of 9% to an increase of 26%. Nonuse values, such as existence and bequest values, could also make a significant contribution to the total value of each site included in this study; however, methodological and data limitations prevented estimating how each operational scenario could change nonuse values.

Carlson, J.L.

1995-03-01T23:59:59.000Z

224

Financial analysis of experimental releases conducted at Glen Canyon Dam during water years 2006 through 2010.  

SciTech Connect

Because of concerns about the impact that Glen Canyon Dam (GCD) operations were having on downstream ecosystems and endangered species, the Bureau of Reclamation (Reclamation) conducted an Environmental Impact Statement (EIS) on dam operations (DOE 1996). New operating rules and management goals for GCD that had been specified in the Record of Decision (ROD) (Reclamation 1996) were adopted in February 1997. In addition to issuing new operating criteria, the ROD mandated experimental releases for the purpose of conducting scientific studies. A report released in January 2011 examined the financial implications of the experimental flows that were conducted at the GCD from 1997 to 2005. This report continues the analysis and examines the financial implications of the experimental flows conducted at the GCD from 2006 to 2010. An experimental release may have either a positive or negative impact on the financial value of energy production. This study estimates the financial costs of experimental releases, identifies the main factors that contribute to these costs, and compares the interdependencies among these factors. An integrated set of tools was used to compute the financial impacts of the experimental releases by simulating the operation of the GCD under two scenarios, namely, (1) a baseline scenario that assumes both that operations comply with the ROD operating criteria and the experimental releases that actually took place during the study period, and (2) a 'without experiments' scenario that is identical to the baseline scenario of operations that comply with the GCD ROD, except it assumes that experimental releases did not occur. The Generation and Transmission Maximization (GTMax) model was the main simulation tool used to dispatch GCD and other hydropower plants that comprise the Salt Lake City Area Integrated Projects (SLCA/IP). Extensive data sets and historical information on SLCA/IP powerplant characteristics, hydrologic conditions, and Western Area Power Administration's (Western's) power purchase prices were used for the simulation. In addition to estimating the financial impact of experimental releases, the GTMax model was also used to gain insights into the interplay among ROD operating criteria, exceptions that were made to criteria to accommodate the experimental releases, and Western operating practices. Experimental releases in some water years resulted in financial benefits to Western while others resulted in financial costs. During the study period, the total financial costs of all experimental releases were more than $4.8 million.

Poch, L. A.; Veselka, T. D.; Palmer, C. S.; Loftin, S.; Osiek, B. (Decision and Information Sciences); (Western Area Power Administration, Colorado River Storage Project Management Center)

2011-08-22T23:59:59.000Z

225

Structural fabric of the Palisades Monocline: a study of positive inversion, Grand Canyon, Arizona  

E-Print Network (OSTI)

A field study of positive inversion is conducted to describe associated structural fabrics and to infer kinematic development of the Palisades Monocline, Grand Canyon, Arizona. These features are then compared to sand, clay and solid rock models of positive inversion to test model results and improve understanding of inversion processes. The N40W 90 oriented Palisades fault underlying the monocline has experienced northeast-southwest Precambrian extension and subsequent northeastsouthwest Laramide contraction. The magnitude of inversion is estimated to be 25% based on vertical offset across the fault, although this does not account for flexure or horizontal shortening. The preferred N50W 90 joint and vein orientation and N50W 68 NE and SW conjugate normal faults are consistent with the Palisades fault and northeastsouthwest extension. The N45E 90 joint orientation and approximately N40W 28 NE and SW conjugate thrust faults are consistent with northeast-southwest contraction. The deformation is characterized by three domains across the fault zone: 1) the hanging wall, 2) the footwall, and 3) an interior, fault-bounded zone between the hanging wall and footwall. Extensional features are preserved and dominate the hanging wall, contractional features define footwall deformation, and the interior, fault-bounded zone is marked by the co-existence of extensional and contractional features. Extension caused a master normal fault and hanging wall roll-over with distributed joints, veinsand normal faults. During inversion, contraction induced reverse reactivation of existing hanging wall faults, footwall folding and footwall thrust-faulting. Precambrian normal slip along the master normal fault and subsequent Laramide reverse slip along the new footwall bounding fault created an uplifted domain of relatively oldest strata between the hanging wall and footwall. Physical models of co-axial inversion suggest consistent development of the three domains of deformation described at the Palisades fault, however the models often require magnitudes of inversion greater than 50%. Although vertical block motion during horizontal compression is not predicted directly by the Mohr-Coulomb criterion, physical models and analytical solutions (incorporating Mohr- Coulomb criterion) suggest maximum stress trajectories and near vertical failure above high angle basement faults that compare favorably with the Palisades fault zone.

Orofino, James Cory

2006-05-01T23:59:59.000Z

226

Integrated reservoir study of the 8 reservoir of the Green Canyon 18 field  

E-Print Network (OSTI)

The move into deeper waters in the Gulf of Mexico has produced new opportunities for petroleum production, but it also has produced new challenges as different reservoir problems are encountered. This integrated reservoir characterization effort has provided useful information about the behavior and characteristics of a typical unconsolidated, overpressured, fine-grained, turbidite reservoir, which constitutes the majority of the reservoirs present in the Outer Continental Shelf of the Gulf of Mexico. Reservoirs in the Green Canyon 18 (GC 18) field constitute part of a turbidite package with reservoir quality typically increasing with depth. Characterization of the relatively shallow 8 reservoir had hitherto been hindered by the difficulty in resolving its complex architecture and stratigraphy. Furthermore, the combination of its unconsolidated rock matrix and abnormal pore pressure has resulted in severe production-induced compaction. The reservoir's complex geology had previously obfuscated the delineation of its hydrocarbon accumulation and determination of its different resource volumes. Geological and architectural alterations caused by post-accumulation salt tectonic activities had previously undermined the determination of the reservoir's active drive mechanisms and their chronology. Seismic interpretation has provided the reservoir geometry and topography. The reservoir stratigraphy has been defined using log, core and seismic data. With well data as pilot points, the spatial distribution of the reservoir properties has been defined using geostatistics. The resulting geological model was used to construct a dynamic flow model that matched historical production and pressure data.. The reservoir's pressure and production behavior indicates a dominant compaction drive mechanism. The results of this work show that the reservoir performance is influenced not only by the available drive energy, but also by the spatial distribution of the different facies relative to well locations. The study has delineated the hydrocarbon bearing reservoir, quantified the different resource categories as STOIIP/GIIP = 19.8/26.2 mmstb/Bscf, ultimate recovery = 9.92/16.01 mmstb/Bscf, and reserves (as of 9/2001) = 1.74/5.99 mmstb/Bscf of oil and gas, respectively. There does not appear to be significant benefit to infill drilling or enhanced recovery operations.

Aniekwena, Anthony Udegbunam

2003-08-01T23:59:59.000Z

227

Large-Eddy Simulation of Flow and Pollutant Transport in Street Canyons of Different Building-Height-to-Street-Width Ratios  

Science Conference Proceedings (OSTI)

This study employs a large-eddy simulation technique to investigate the flow, turbulence structure, and pollutant transport in street canyons of building-height-to-street-width (aspect) ratios of 0.5, 1.0, and 2.0 at a Reynolds number of 12 000 ...

Chun-Ho Liu; Mary C. Barth; Dennis Y. C. Leung

2004-10-01T23:59:59.000Z

228

Near-Surface Currents in DeSoto Canyon (199799): Comparison of Current Meters, Satellite Observation, and Model Simulation  

Science Conference Proceedings (OSTI)

This study evaluates a data-assimilated model simulation of near-surface circulation in DeSoto Canyon (DSC), Gulf of Mexico, with emphasis on analyzing moored current-meter observations and comparing them with satellite data and model results. ...

Dong-Ping Wang; Lie-Yauw Oey; Tal Ezer; Peter Hamilton

2003-01-01T23:59:59.000Z

229

Renewable Energy Engineering  

E-Print Network (OSTI)

MSc in Renewable Energy Engineering School of Engineering www.cranfield.ac.uk/soe/renewableenergy #12;Postgraduate study Cranfield University 2 School of Engineering MSc in Renewable Energy Engineering Renewable Energy Engineering MSc in Climate change, growing world populations and limited fossil

230

Chemical engineering Research !!  

E-Print Network (OSTI)

Chemical engineering Research !! www.chemeng.lth.se Updated August 2012 #12;WWT Fermentation University/Faculty of Engineering-LTH/Department of Chemical Engineering Membrane Group Ann-Sofi Jönsson More research projects. #12;Lund University/Faculty of Engineering-LTH/Department of Chemical Engineering

231

Engineering Fundamentals - Electrical Engineering, Version 2.0  

Science Conference Proceedings (OSTI)

Engineering Fundamentals Electrical Engineering (EF-EE) covers the basics of electrical engineering topics. The module provides information about basic electrical engineering terms and concepts that help identify ...

2013-02-05T23:59:59.000Z

232

High-Resolution Carbon Isotope Stratigraphy, Pennsylvanian Snaky Canyon Formation, East-Central Idaho: Implications for Regional and Global Correlations  

E-Print Network (OSTI)

Nearly 550 samples of fine grained carbonates, collected every 0.5 to 1.0 m from the Bloom Member of the Snaky Canyon Formation at Gallagher Peak, Idaho, were analyzed to determine the high-resolution carbon isotope stratigraphy. To constrain for diagenesis, thin sections were petrographically analyzed and viewed using cathodoluminescence microscopy. Chemical analyses were performed using an electron microprobe. Average delta18O and delta13C values from the Bloom Member are -4.5% +/- 1.6% (1 sigma) and 2.1% +/- 1.1%, respectively. Maximum delta13C values are about 1% higher for the Desmoinesian and Missourian than the Morrowan and Atokan, similar to results from the Yukon Territory. delta18O and delta13C values are lowest for crystalline mosaic limestones and siltstones, moderate for packstones, wackestones, and mudstones, and highest for boundstones and grainstones. The delta13C profile from Gallagher Peak consists of high frequency 1% oscillations with several larger excursions. No large delta13C increase at the base of the section suggests the Mid-Carboniferous boundary is in the underlying Bluebird Mountain formation. delta13C of Gallagher Peak and Arrow Canyon, NV, correlate well from 318 to 310 Ma, but correlation becomes more difficult around 310 Ma. This may result from increased restriction of the Snaky Canyon platform beginning in the Desmoinesian. Most of the short term (<1 Ma) isotopic excursions are the result of diagenesis. Two of the largest negative excursions at Gallagher Peak correlate with two large negative excursions at Big Hatchet Peak, NM, possibly due to sea level lowstands of the Desmoinesian. Phylloid algal mounds at Gallagher Peak are associated with positive excursions because of original aragonite composition and increased open marine influence. Positive excursions related to other facies characteristics also result from increased marine influence. The delta13C curve for the upper half of Gallagher Peak contains three repeated cycles of increasing delta13C over 1-1.5 Ma, which are possibly related to long-term sea level fluctuations. Given the complexity of each local environment, without detailed biostratigraphy, detailed rock descriptions, and analysis of the various rock components, delta13C stratigraphy of whole rocks can be misinterpreted.

Jolley, Casey

2012-05-01T23:59:59.000Z

233

Underground Infrastructure Impacts Due to a Surface Burst Nuclear Device in an Urban Canyon Environment  

SciTech Connect

Investigation of the effects of a nuclear device exploded in a urban environment such as the Chicago studied for this particular report have shown the importance on the effects from the urban canyons so typical of today's urban environment as compared to nuclear test event effects observed at the Nevada Test Site (NTS) and the Pacific Testing Area on which many of the typical legacy empirical codes are based on. This report first looks at the some of the data from nuclear testing that can give an indication of the damage levels that might be experienced due to a nuclear event. While it is well known that a above ground blast, even a ground burst, very poorly transmits energy into the ground ( < 1%) and the experimental results discussed here are for fully coupled detonations, these results do indicate a useful measure of the damage that might be expected. The second part of the report looks at effects of layering of different materials that typically would make up the near ground below surface environment that a shock would propagate through. As these simulations support and is widely known in the community, the effects of different material compositions in these layers modify the shock behavior and especially modify the energy dispersal and coupling into the basement structures. The third part of the report looks at the modification of the underground shock effects from a surface burst 1 KT device due to the presence of basements under the Chicago buildings. Without direct knowledge of the basement structure, a simulated footprint of a uniform 20m depth was assumed underneath each of the NGI defined buildings in the above ground environment. In the above ground case, the underground basement structures channel the energy along the line of site streets keeping the shock levels from falling off as rapidly as has been observed in unobstructed detonations. These simulations indicate a falloff of factors of 2 per scaled length as compared to 10 for the unobstructed case. Again, as in the above ground case, the basements create significant shielding causing the shock profile to become more square and reducing the potential for damage diagonal to the line of sight streets. The results for a 1KT device is that the heavily damaged zone (complete destruction) will extend out to 50m from the detonation ({approx}100m for 10KT). The heavily to moderately damaged zone will extend out to 100m ({approx}200m for 10KT). Since the destruction will depend on geometric angle from the detonation and also the variability of response for various critical infrastructure, for planning purposes the area out to 100m from the detonation should be assumed to be non-operational. Specifically for subway tunnels, while not operational, they could be human passable for human egress in the moderately damaged area. The results of the simulations presented in this report indicate only the general underground infrastructure impact. Simulations done with the actual basement geometry would be an important improvement. Equally as important or even more so, knowing the actual underground material configurations and material composition would be critical information to refine the calculations. Coupling of the shock data into structural codes would help inform the emergency planning and first response communities on the impact to underground structures and the state of buildings after the detonation.

Bos, Randall J. [Los Alamos National Laboratory; Dey, Thomas N. [Los Alamos National Laboratory; Runnels, Scott R. [Los Alamos National Laboratory

2012-07-03T23:59:59.000Z

234

Stirling Engine Assessment  

Science Conference Proceedings (OSTI)

Stirling engines are reciprocating engines that are fueled by an external heat source. This report presents a summary of the technical trends, commercialization status, and economic viability of Stirling engine technology for distributed generation (DG) applications.

2002-10-28T23:59:59.000Z

235

Science Technology Engineering Math Science Technology Engineering Math Mechanical Engineering Aerospace Engineering  

E-Print Network (OSTI)

Science Technology Engineering Math Science Technology Engineering Math Mechanical Engineering Loop glider Airboat Straw rockets College Class Science Activity Stomp rockets Underwater copters AND/OR Circuits College Class Science Activity Electronic T/F Motorized flying gliders

Rohs, Remo

236

DOE Solar Decathlon: Engineering  

NLE Websites -- All DOE Office Websites (Extended Search)

U.S. Department of Energy Solar Decathlon Contests Engineering The U.S. Department of Energy Solar Decathlon houses represent the best of modern engineering. For the Engineering...

237

Engineering Experimentation - Nuclear Engineering Division (Argonne...  

NLE Websites -- All DOE Office Websites (Extended Search)

such as corrosivehazardous materials, high-temperature structural integrity, and remote handling. More... NE Departments involved: Engineering Development and...

238

Decreasing Slip Rates From12.8 Ma to Present on the Solitario Canyon Fault at Yucca Mountain, Nevada  

DOE Green Energy (OSTI)

The Solitario Canyon fault, which bounds the west side of Yucca Mountain, Nevada, is the closest fault with Quaternary offset adjacent to the proposed spent nuclear fuel and high-level radioactive waste repository. Dip-slip offset between 12.8 and 10.7 Ma is determined from lithostratigraphic displacement in boreholes USW H-3 and USW WT-7, drilled in the footwall and hanging wall, respectively. The base of the 12.8-Ma Topopah Spring Tuff is interpreted to have 463.3 m of separation across the fault, an average dip slip rate of 0.036 mm/yr. Previous researchers identified a geothermal system active from 11.5 to 10.0 Ma with peak activity at 10.7 Ma that resulted in pervasive alteration of vitric rock to zeolitic minerals where the rocks were in the ground-water saturated zone. The contact between vitric (V) and pervasively zeolitic (Z) rocks cuts across the lithostratigraphic section and offset of this V-Z boundary can be used to measure slip rates between 12.8 and 10.7 Ma. In H-3, the V-Z boundary is 138.4 m below the base of the vitric, densely welded subzone of the Topopah Spring Tuff (Tptpv3). In WT-7, although the V-Z boundary is identified at the base of the Tptpv3, borehole video, cuttings, and geophysical log data indicate the Tptpv3 has well-developed zeolitic alteration along fractures, and this implies 19.5 m of the total thickness of Tptpv3 (and probably additional overlying crystallized rocks) also were in the saturated zone by 10.7 Ma. The V-Z relations across the Solitario Canyon fault in H-3 and WT-7 indicate a minimum of 157.9 m of separation before 10.7 Ma, which is 34.1 percent of the total slip of the Topopah Spring Tuff, and a minimum dip slip rate of 0.075 mm/yr from 12.8 to 10.7 Ma. These data are consistent with the broader structural history of the area near Yucca Mountain. Previous workers used angular unconformities, tilting of structural blocks, and paleomagnetic data to constrain the main period of extensional faulting between 12.7 and 8.5 Ma. Paleoseismic studies in Quaternary deposits documented slip rates on the Solitario Canyon fault from 0.01 to 0.02 mm/yr since 0.077 and 0.20 Ma. The decrease of extensional activity slip rates data on the Solitario Canyon fault provide evidence of decreasing tectonic activity from the middle Miocene to present.

D. Buesch

2006-07-11T23:59:59.000Z

239

Ultimate search engine.  

E-Print Network (OSTI)

??The search engine is a tool designed to search for information on the web according to the keywords specified by users. Different search engines are (more)

Patel, Chirag

2012-01-01T23:59:59.000Z

240

HCCI engine control and optimization  

E-Print Network (OSTI)

natural gas engine setup for stationary power generation. . . . . . . . . . .natural gas engine setup for stationary power generation.

Killingsworth, Nicholas J.

2007-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Life Cycle Engineering Group  

Science Conference Proceedings (OSTI)

... for green manufacturing and construction applications; conduct life cycle engineering assessments for energy efficiency and environmental ...

2012-08-23T23:59:59.000Z

242

and Chemical Engineering  

E-Print Network (OSTI)

Biological and Chemical Engineering Building #12;2 Biological and Chemical Engineering Building sta is constructing a new building that will house the Department of Chemical Engineering and the Department and Chemical Engineering Building will provide critically needed space for innovators in multiple disciplines

Prinz, Friedrich B.

243

Combined-Admission Engineering.  

E-Print Network (OSTI)

that include relevant engineering experiences, such as FIRST Robotics, Talent Search, or Science/Math Bowl students with an assurance of admission to the Hajim School of Engineering and Applied Sciences in one Science · Electrical and Computer Engineering · Materials Science · Mechanical Engineering · Optics

Portman, Douglas

244

Argonne TDC: Engineering Technologies  

Emergency Response. Engineering. Environmental Research. Fuel Cells. Imaging Technology. Material Science. Nanotechnology. Physical Sciences. Sensor ...

245

Artificial Intelligence and Systems Engineering  

E-Print Network (OSTI)

/PR URL: http://www.dotomi.com Job Titles: Engineering/IT Apprentice, Client Development/Sales Apprentice, Media Apprentice, Account Management Apprentice, Quality Assurance Apprentice Majors: Business: Business. - BS, Engineering: Contract Major, Engineering: Electrical, Engineering: Industrial, Engineering

Sommerville, Ian

246

Engineering and Structural Mechanics - Nuclear Engineering Division  

NLE Websites -- All DOE Office Websites (Extended Search)

Engineering and Structural Mechanics Engineering and Structural Mechanics Capabilities Engineering Computation and Design Engineering and Structural Mechanics Overview Areas of Application Examples of Analyses Systems/Component Design, Engineering and Drafting Heat Transfer and Fluid Mechanics Multi-physics Reactor Performance and Safety Simulations Other Capabilities Work with Argonne Contact us For Employees Site Map Help Join us on Facebook Follow us on Twitter NE on Flickr Engineering and Structural Mechanics Bookmark and Share Analysis of a Reinforced Concrete Structure using the NEPTUNE Finite Element Code Analysis of a Reinforced Concrete Structure using the NEPTUNE Finite Element Code. Depicted are Cracks in the Concrete Surface due to an Internal Pressurization. Click on image to view larger image.

247

Engineering Analysis - Nuclear Engineering Division (Argonne)  

NLE Websites -- All DOE Office Websites (Extended Search)

Analysis Analysis DEPARTMENTS Engineering Analysis Nuclear Systems Analysis Research & Test Reactor Nonproliferation and National Security Detection & Diagnostic Systems Engineering Development & Applications Work with Argonne Contact us For Employees Site Map Help Join us on Facebook Follow us on Twitter NE on Flickr Celebrating the 70th Anniversary of Chicago Pile 1 (CP-1) Argonne OutLoud on Nuclear Energy Argonne Energy Showcase 2012 Engineering Analysis Bookmark and Share The Engineering Analysis Department activities focus on development and application of new and innovative analysis methods for both nuclear and non-nuclear systems. The Department is organized into sections and groups for Engineering Simulations, Safety Analysis, Innovative Systems Development, Engineering Assessments, Plant Analysis & Control, Process

248

Ruby, Alaska: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

394444°, -155.4869444° 394444°, -155.4869444° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":64.7394444,"lon":-155.4869444,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

249

Engineering Computation and Design - Nuclear Engineering Division...  

NLE Websites -- All DOE Office Websites (Extended Search)

applied in such diverse areas as vacuum and cryogenic systems, manufacturing engineering, hot cell equipment, and spent fuel processing systems. More... NE Departments involved:...

250

INCREASING OIL RECOVERY THROUGH ADVANCED REPROCESSING OF 3D SEISMIC, GRANT CANYON AND BACON FLAT FIELDS, NYE COUNTY, NEVADA  

SciTech Connect

Makoil, Inc., of Orange, California, with the support of the U.S. Department of Energy has reprocessed and reinterpreted the 3D seismic survey of the Grant Canyon area, Railroad Valley, Nye County, Nevada. The project was supported by Dept. of Energy Grant DE-FG26-00BC15257. The Grant Canyon survey covers an area of 11 square miles, and includes Grant Canyon and Bacon Flat oil fields. These fields have produced over 20 million barrels of oil since 1981, from debris slides of Devonian rocks that are beneath 3,500 to 5,000 ft of Tertiary syntectonic deposits that fill the basin of Railroad Valley. High-angle and low-angle normal faults complicate the trap geometry of the fields, and there is great variability in the acoustic characteristics of the overlying valley fill. These factors combine to create an area that is challenging to interpret from seismic reflection data. A 3D seismic survey acquired in 1992-93 by the operator of the fields has been used to identify development and wildcat locations with mixed success. Makoil believed that improved techniques of processing seismic data and additional well control could enhance the interpretation enough to improve the chances of success in the survey area. The project involved the acquisition of hardware and software for survey interpretation, survey reprocessing, and reinterpretation of the survey. SeisX, published by Paradigm Geophysical Ltd., was chosen as the interpretation software, and it was installed on a Dell Precision 610 computer work station with the Windows NT operating system. The hardware and software were selected based on cost, possible addition of compatible modeling software in the future, and the experience of consulting geophysicists in the Billings area. Installation of the software and integration of the hardware into the local office network was difficult at times but was accomplished with some technical support from Paradigm and Hewlett Packard, manufacturer of some of the network equipment. A number of improvements in the processing of the survey were made compared to the original work. Pre-stack migration was employed, and some errors in muting in the original processing were found and corrected. In addition, improvements in computer hardware allowed interactive monitoring of the processing steps, so that parameters could be adjusted before completion of each step. The reprocessed survey was then loaded into SeisX, v. 3.5, for interpretation work. Interpretation was done on 2, 21-inch monitors connected to the work station. SeisX was prone to crashing, but little work was lost because of this. The program was developed for use under the Unix operating system, and some aspects of the design of the user interface betray that heritage. For example, printing is a 2-stage operation that involves creation of a graphic file using SeisX and printing the file with printer utility software. Because of problems inherent in using graphics files with different software, a significant amount of trial and error is introduced in getting printed output. Most of the interpretation work was done using vertical profiles. The interpretation tools used with time slices are limited and hard to use, but a number to tools and techniques are available to use with vertical profiles. Although this project encountered a number of delays and difficulties, some unavoidable and some self-inflicted, the result is an improved 3D survey and greater confidence in the interpretation. The experiences described in this report will be useful to those that are embarking on a 3D seismic interpretation project.

Eric H. Johnson; Don E. French

2001-06-01T23:59:59.000Z

251

Late Pleistocene to Recent sediment transport pathways of the Green Canyon OCS area, northern Gulf of Mexico  

E-Print Network (OSTI)

This study addresses some of the complexities of sediment transport systems on the continental slope of the Green Canyon OCS area south of the Louisiana coast. Five Late Pleistocene to Recent sedimentary sequences are identified using a combination of seismic and well data. Sediments are transported through pathways characterized by erosional surfaces and numerous channels which form as sediments remobilize and become transported downslope. Pathway margins are constricted by physiographic highs. Several processes are identified as means of carrying fine-grained sediments to and across the continental slope. The most important of these are mass movements (slumps and slides), debris flows, and turbidity currents. Faulting and/or slumping at the shelf edge remobilizes sediments which are then carried further downslope. These remobilized sediments may be transported as debris flows or other undifferentiated high-density flows, or may develop into turbidity currents which deposit graded sediments in response to decreases in slope gradient. Slumps and slides off salt uplifts also deposit large volumes of sediments into adjacent intraslope basins and sediment transport pathways, where they may contribute significant amounts of material to the downslope transport of sediments. Discrete channels are not often observed in the pathways due to multiple episodes of channel formation and erosion which occurred during a single sea level lowstand. These multiple episodes tend to remove or obscure prominent channel features. Sedimentation is cyclic. During one sea level lowstand a sequence is deposited in and along narrow pathways which successively fill intraslope basins from the shelf edge downslope. As each basin is filled, sediments spill over and continue downslope to a lower basin. Sedimentation during the next sea level lowstand occurs in broader pathways. Less sediments are deposited in the intraslope basin areas because they remain filled from the previous sequence. By the time of deposition of the next sequence, movement of underlying salt sheets has changed the shape of the pathway. The sedimentation pattern repeats as lower depressions fill and sediments spill over. Pathways transport slope sediments in the Green canyon area. Discrete channels are not often observed in the pathways. This is a result of two mechanisms: 1) multiple episodes of erosion during a sea level lowstand tend to remove or obscure prominent channel features, and 2) most sediments deposited within the pathways are mass transport deposits which do not often become channelized. The pathways are characterized by erosional surfaces and numerous conduits which form as sediments remobilize and become transported downslope. They are laterally relatively persistent, being constricted by structural highs,

Swanson, John Patrick

1994-01-01T23:59:59.000Z

252

Analyzing the connectivity potential of landscape geomorphic systems: a radar remote sensing and GIS approach, Estufa Canyon, Texas, USA  

E-Print Network (OSTI)

Connectivity is considered one of the fundamental aspects that influences the rate of mass movement in the landscape. The connectivity aspect has been acknowledged from various conceptual geomorphic frameworks. None of these provided a developmental methodology for studying the connectivity of geomorphic systems, especially at the scale of the fluvial system. The emphasis in this research is placed on defining variables of the geomorphic systems that influence the connectivity potential of these systems. The landscape gradient, which is extracted from the Digital Elevation Model (DEM), and the surface roughness, which is extracted from radar images, are used to analyze the connectivity potential of geomorphic systems in the landscape. Integration of these variables produces a connectivity potential index of the various geomorphic systems that compose the fluvial system. High values of the connectivity potential index indicate high potential of the geomorphic system to transport mass whereas the low values indicate low potential of the geomorphic system to transport mass in the landscape. Using the mean values of the connectivity potential index, the geomorphic systems in the landscape can be classified into geomorphic systems of low connectivity potential, geomorphic systems of intermediate connectivity potential and geomorphic systems of high connectivity potential. In addition to the determination of the relative connectivity potential of various geomorphic systems, the connectivity potential index is used to analyze the system-wide connectivity. The ratios between the connectivity potential index of the upstream geomorphic systems and the connectivity potential index of the downstream geomorphic systems define system-wide connectivity in the landscape. High ratios reflect the high potential of the upstream geomorphic systems to transport mass in the downstream direction. Low ratios indicate the influence of the downstream geomorphic systems in maximizing mass movement in the upstream geomorphic systems. The presence of high and low ratios suggests the presence of a high system-wide connectivity. As the ratio approaches unity, mass movement is minimized in the landscape indicating low system-wide connectivity. Applying the above approach to Estufa Canyon, Texas, illustrated that Estufa Canyon is a dynamic fluvial system with high system-wide connectivity.

Ibrahim, ElSayed Ali Hermas

2005-08-01T23:59:59.000Z

253

The Entire Engineering Archive  

NLE Websites -- All DOE Office Websites (Extended Search)

Engineering Archives Engineering Archives Engineering Archives, Since November 1991 Table of Contents: Strongest geometric figure Geometric figures - bridges High school preparation for engineering Engineering fields and mathematics Future of mechanical engineering Absorbing energy in a crash Braking force of automobiles US fast-breeder policy Fusion energy to power Electricity generation Photovoltaic motors Variable speed motor Space plane Building on the moon Why does the Shuttle turn on launch? Gyroscopes Triangulation Magnets in speakers Speaker impedance Permanent magnet manufacture E/M interference FM modulation Pressure rise in pipe expansion Drag coefficient and Reynolds' Number Boundary layers Cavitation Is it more efficient to turn off fluorescent Uninterruptable power supply Electrical current

254

VacuumEngineering  

NLE Websites -- All DOE Office Websites (Extended Search)

Engineering Engineering Manufacturing Technologies The Manufacturing, Science & Technology Center engineers, fabricates, assembles and characterizes vacuum systems, components, and processes. Staff can trouble shoot and upgrade existing vacuum systems. Capabilities * Engineering expertise to define, design and fabricate vacuum furnaces, deposition sys- tems and any vacuum environment based process or experimental system * Computer-aided engineering of systems including parametric 3-D solid modeling with ProDesktop (Parametric Design) * Outgassing rate measurements and mass spectroscopy of materials and components * Machining and welding capability for con- structing unique vacuum components for prototype or production applications Resources * Experienced design engineering and fabrication

255

NUCLEAR GAS ENGINE  

SciTech Connect

A preliminary design study of the nuclear gas engine, consisting of a gas-cooled reactor directly coupled to a reciprocating engine, is presented. The principles of operation of the proposed gas engine are outlined and typical variations anre discussed. The nuclear gas engine is compared with other reciprocating engines and air compressors. A comparison between the ideal and actual cycles is made, with particular attention given to pumping, heat, and other losses to be expected. The applications and development of the nuclear gas engine are discussed. (W.D.M.)

Fraas, A.P.

1958-09-25T23:59:59.000Z

256

The Phillips Stirling engine  

SciTech Connect

This book is about the Stirling engine and its development from the heavy cast-iron machine of the 19th century to that of today. It is a history of a research effort spanning nearly 50 years, together with an outline of principles, and some technical details and descriptions of the more important engines. Contents include: the hot-air engine; the 20th-century revival; the Stirling cycle; rhombic-drive engines; heating and cooling; pistons and seals; electric generators and heat pumps; exotic heat sources; the engine and the environment; swashplate engines; and the past and the future.

Hargreaves, C.M.

1991-01-01T23:59:59.000Z

257

Draft Supplement to the Environmental Statement Fiscal Year 1976 Proposed Program : Facilty Location Evaluation for Franklin-Badger Canyon 230-kV Line and Badger Canyon Substation Study Area 74-6B.  

SciTech Connect

Proposed is the construction of a 15-mile, 230-kV double-circuit transmission line from Franklin Substation near Pasco, Washington, to a proposed new Badger Canyon Substation to be constructed 5 miles west of Kennewick, Washington. Depending on the final route location chosen, approximately 15 miles of 230-kV double circuit transmission line requiring 5.6 miles of new and 9.4 miles of existing right-of-way would be needed as well as approximately 2500 feet of new access road. Land use affected includes crossing Sacajawea State Park and passig through irrigated cropland and grassland on existing right-of-way, and depending on the alternative route chosen, could cross land proposed for residential development and a proposed interstate highway. An additional 10 to 11 acres of potential cropland would be required for the proposed substation. Disturbance to wildlife during construction would occur and habitat associated with the above land uses would be eliminated. Some erosion and sedimentation would occur. Visual impacts would affect Sacajawea State Park, a proposed highway, and potential residential development land. Noise and other disturbances to residents will occur, primarily during construction.

United States. Bonneville Power Administration.

1974-10-22T23:59:59.000Z

258

College of Engineering CME Chemical Engineering  

E-Print Network (OSTI)

: COM 199, CME 455, CME 550 and engineering standing. CME 462 PROCESS CONTROL. (3) Basic theory. Technologies covered include coal, natural gas, nuclear, biomass, wind, solar and advanced technologies. Prereq: Engineering standing or consent of instructor. (Same as EGR 542.) CME 550 CHEMICAL REACTOR DESIGN. (3

Kim, Mi-Ok

259

Electrical engineering Electricity  

E-Print Network (OSTI)

generation Transmission Distribution · Electrical generators · Electric motors · High voltage engineering associated with the systems Electrical engineering · Electric power generation Transmission Distribution The electricity transported to load locations from a power station transmission subsystem The transmission system

?nay, Devrim

260

Engine lubrication oil aeration  

E-Print Network (OSTI)

The lubrication system of an internal combustion engine serves many purposes. It lubricates moving parts, cools the engine, removes impurities, supports loads, and minimizes friction. The entrapment of air in the lubricating ...

Baran, Bridget A. (Bridget Anne)

2007-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Use of Modeling for Prevention of Solids Formation During Canyon Processing of Legacy Nuclear Materials at the Savannah River Site  

Science Conference Proceedings (OSTI)

The Savannah River Site (SRS) Environmental Management (EM) nuclear material stabilization program includes the dissolution and processing of legacy materials from various DOE sites. The SRS canyon facilities were designed to dissolve and process spent nuclear fuel and targets. As the processing of typical materials is completed, unusual and exotic nuclear materials are being targeted for stabilization. These unusual materials are often difficult to dissolve using historical flowsheet conditions and require more aggressive dissolver solutions. Solids must be prevented in the dissolver to avoid expensive delays associated with the build-up of insoluble material in downstream process equipment. Moreover, it is vital to prevent precipitation of all solids, especially plutonium-bearing solids, since their presence in dissolver solutions raises criticality safety issues. To prevent precipitation of undesirable solids in aqueous process solutions, the accuracy of computer models to predict precipitate formation requires incorporation of plant specific fundamental data. These data are incorporated into a previously developed thermodynamic computer program that applies the Pitzer correlation to derive activity coefficient parameters. This improved predictive model will reduce unwanted precipitation in process solutions at DOE sites working with EM nuclear materials in aqueous solutions.

Rhodes, W. D.; Crooks III, W. J.; Christian, J. D.

2002-02-26T23:59:59.000Z

262

Floodplain Assessment for the Proposed Outdoor Fire Range Upgrades at TA-72 in Lower Sandia Canyon, Los Alamos National Laboratory  

Science Conference Proceedings (OSTI)

Los Alamos National Laboratory (LANL) is preparing to implement actions in Sandia Canyon at Technical Area (TA) 72. Los Alamos National Security (LANS) biologists conducted a floodplain determination and this project is partially located within a 100-year floodplain. The proposed project is to upgrade the existing outdoor shooting range facilities at TA-72. These upgrades will result in increased safety and efficiencies in the training for Protective Force personnel. In order to remain current on training requirements, the firing ranges at TA-72 will be upgraded which will result in increased safety and efficiencies in the training for Protective Force personnel (Figure 1). These upgrades will allow for an increase in class size and more people to be qualified at the ranges. Some of these upgrades will be built within the 100-year floodplain. The upgrades include: concrete pads for turning target systems and shooting positions, new lighting to illuminate the firing range for night fire, a new speaker system for range operations, canopies at two locations, an impact berm at the far end of the 300-yard mark, and a block wall for road protection.

Hathcock, Charles D. [Los Alamos National Laboratory

2012-08-27T23:59:59.000Z

263

Structural restoration of Louann Salt and overlying sediments, De Soto Canyon Salt Basin, northeastern Gulf of Mexico  

E-Print Network (OSTI)

The continental margin of the northeastern Gulf of Mexico is suited for seismic stratigraphic analysis and salt tectonism analysis. Jurassic strata include the Louann Salt on the continental shelf and upper slope of the Destin Dome OCS area, northeastern Gulf of Mexico. These sediments were deposited in a slowly subsiding, stable tectonic environment. Two-dimensional (2-D) seismic data, supplemented with well log, paleontologic and velocity information were used to infer structural and stratigraphic features, especially small faults in the deep part of the De Soto Canyon Salt Basin area. Six sequence boundaries or correlative paleohorizons were interpreted on Landmark seismic interpretation workstation. They are Base of Salt or Equivalent, Top of Salt, Top of Smackover Formation, Top of Cotton Valley Group, Middle Cretaceous sequence boundary, and Top of Upper Cretaceous. Information generated from structural and stratigraphic analysis are used to analyze the evolution of salt movement and salt mechanism in this area. I used a software package Restore (Dan Schultz-Ela and Ken Duncan, 1991) for structural restoration. This program is suitable for extensional terrane. The restoration of one depth section was achieved through steps introduced by Restore. Regional extension, gravity spreading, and gliding are the most important mechanism of salt flow, buoyancy and differential loading mainly contribute to the vertical development of salt structure in this area.

Guo, Mengdong

1997-01-01T23:59:59.000Z

264

NSLS Operations & Engineering  

NLE Websites -- All DOE Office Websites (Extended Search)

Operations & Engineering Electrical Equipment Controls & Diagnostics Computer Systems Power Systems Mechanical Design Mechanical Tech Utilities Vacuum Work Planning & Controls...

265

Systems Engineering Group  

Science Conference Proceedings (OSTI)

... advances, and deploys measurement science to address application of engineering information systems to complex cyber-physical systems. ...

2011-10-03T23:59:59.000Z

266

Reducing Diesel Engine Emissions  

NLE Websites -- All DOE Office Websites (Extended Search)

Reducing Reducing Diesel Engine Emissions 2 0 1 0 Green TransporTaTion TechnoloGies Compared to traditional gasoline engines, diesel engines require less maintenance, generate energy more efficiently, and produce less carbon dioxide emissions. But when uncontrolled, diesel engines churn out harmful emissions like particu- late matter (PM) and nitrogen oxides (NO x ). Researchers at Argonne National Laboratory are currently working to develop

267

Topic: Wind Engineering  

Science Conference Proceedings (OSTI)

Topic: Wind Engineering. Forty-Fourth Meeting of the UJNR Panel on Wind and Seismic Effects. NIST researchers collected ...

2011-08-31T23:59:59.000Z

268

Chemical Engineering & Processing Thermodynamics ...  

Science Conference Proceedings (OSTI)

... Engineering & Processing Thermodynamics Information at ... Phase Equilibrium Data (01/30 ... Connecting Thermodynamic and Dynamic Properties of ...

2010-09-24T23:59:59.000Z

269

Journal of Biological Engineering  

5Department of Electrical Engineering, University of California, Berkeley, CA 94720, USA ... Institute of Science and Technology, Ulsan, Korea

270

Engineering Laboratory Homepage  

Science Conference Proceedings (OSTI)

... and InfrastructureDisaster-Resilient Buildings, Infrastructure, and ... of the Manufacturing Engineering Laboratory. ... Net-Zero Energy Residential Test ...

2013-08-12T23:59:59.000Z

271

Energy Technology Engineering Center  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Technology Engineering Center Technology Engineering Center 41 00 Guardian Street, Suite # 160 Simi Valley, CA 93063 Memorandum for: Gregory H. Woods General Council January 30, 2013 FROM: John Jones EL\= Federal Proje� irector Energy Technology Engineering Center (ETEC) Project Office SUBJECT: Annual National Environmental Policy Act {NEPA) Planning Summary Attached is the 2013 Annual NEPA Planning Summary for the ETEC Project Office.

272

UML for systems engineering  

Science Conference Proceedings (OSTI)

The paper provides an introduction to the employment of Unified Modeling Language (UML) in systems engineering. The standard being developed for this purpose is the Systems Modeling Language (SysML) specification. This paper, while not dealing with SysML ... Keywords: DoDAF, Software engineering, SysML, Systems engineering, UML

Brian Willard

2007-01-01T23:59:59.000Z

273

ELECTRICAL & COMPUTER ENGINEERING  

E-Print Network (OSTI)

ELECTRICAL & COMPUTER ENGINEERING SEMINAR "Considerations for Curriculum Planning and Revitalization in Engineering" by Prof. Michael A. de Miranda School of Education and Department of Electrical and Computer Engineering Colorado State University Monday, Feb. 20, 2012, 11:00 a.m. Location: LSC 210 Abstract

274

ELECTRICAL & COMPUTER ENGINEERING  

E-Print Network (OSTI)

Electrical, Computer, and Energy Engineering University of Colorado--Boulder Monday, April 2, 2012, 11:00 a an Associate Professor with the Department of Electrical Engineering, University of Colorado, Boulder. He hadELECTRICAL & COMPUTER ENGINEERING SEMINAR "A Random Walk on Image Patches" by Prof. Francois Meyer

275

Combined-Admission Engineering.  

E-Print Network (OSTI)

experiences, such as FIRST Robotics, Talent Search, or Science/Math Bowl Admission If you're selected of admission to the Hajim School of Engineering and Applied Sciences in one of nine master's programs: · Alternative Energy · Biomedical Engineering · Chemical Engineering · Computer Science · Electrical

Portman, Douglas

276

Combined-Admission Engineering.  

E-Print Network (OSTI)

Search, or Science/Math Bowl Admission If you're selected for a GEAR interview, you'll be notified of admission to the Hajim School of Engineering and Applied Sciences in one of nine master's programs: · Alternative Energy · Biomedical Engineering · Chemical Engineering · Computer Science · Electrical

Portman, Douglas

277

DATA SEARCH ENGINE INTRODUCTION  

E-Print Network (OSTI)

users to enter more specific and complex queries. Most search engines cover only a small portion the proximity of the query terms within a page. As another example, a search engine may keep track of the number is also mostly true as the average number of terms in a search engine query is slightly over two. When

Meng, Weiyi

278

Transportation Engineering Graduate Programs Department of Civil & Environmental Engineering  

E-Print Network (OSTI)

Transportation Engineering Graduate Programs Department of Civil & Environmental Engineering Maseeh College of Engineering & Computer Science STUDY TRANSPORTATION ENGINEERING AT Portland, Oregon is famous for its multimodal transportation system. Why not come to Portland State University and study

Bertini, Robert L.

279

PhD Chemical Engineering MS Chemical Engineering  

E-Print Network (OSTI)

1 PhD Chemical Engineering MS Chemical Engineering Bylaws Gene and Linda Voiland School of ChemicalD Chemical Engineering, MS Chemical Engineering B. Discipline: Edgar, et al.1 provide a succinct description of chemical engineering: "chemical engineers seek to understand, manipulate, and control the molecular basis

Collins, Gary S.

280

Chemical Engineering The George R. Brown School of Engineering  

E-Print Network (OSTI)

110 Chemical Engineering The George R. Brown School of Engineering Chair Kyriacos Zygourakis of study leading to the nonthesis Master of Chemical Engineering (M.Ch.E.) degree. A joint M, and biomedical engineering. #12;Chemical Engineering 111 Degree Requirements for B.S. in Chemical Engineering

Richards-Kortum, Rebecca

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Chemical Engineering The George R. Brown School of Engineering  

E-Print Network (OSTI)

117 Chemical Engineering The George R. Brown School of Engineering Chair Kyriacos Zygourakis,studentsmayapplyforafifthyearofstudyleadingtothenonthesis Master of Chemical Engineering (M.Ch.E.) degree. A joint M.B.A./M.Ch.E. degree is also available, and biomedical engineering. #12;Chemical Engineering 119118 DEPARTMENTS / Chemical Engineering For CENG 301 Math

Richards-Kortum, Rebecca

282

Chemical Engineering The George R. Brown School of Engineering  

E-Print Network (OSTI)

120 Chemical Engineering The George R. Brown School of Engineering Chair Kyriacos Zygourakis,studentsmayapplyforafifthyearofstudyleadingtothenonthesis Master of Chemical Engineering (M.Ch.E.) degree. A joint M.B.A./M.Ch.E. degree is also available, and biomedical engineering. #12;Chemical Engineering 121 Degree Requirements for B.S. in Chemical Engineering

Richards-Kortum, Rebecca

283

MECHANICAL ENGINEERING UNDERGRADUATE DEGREES --TUFTS UNIVERSITY SCHOOL OF ENGINEERING  

E-Print Network (OSTI)

of Science in Biomedical Engineering* BSBME Biomedical Eng BME --ineering CHEMICAL & BIOLOGICA ENGINEERING L Bachelor of Science in Chemical Engineering* BSCHE Chemical Engin CHE --eering CIVIL & ENVIRONMENTA ENGINEERING Bachelor of Science in Civil Engineering* BSCE Civil Engineerin CE --g L Bachelor of Science

Tufts University

284

NREL: Photovoltaics Research - Engineering  

NLE Websites -- All DOE Office Websites (Extended Search)

Photovoltaic Engineering Photovoltaic Engineering Photovoltaic (PV) Engineering at NREL supports commercial and emerging PV technology development. Our support covers the following three areas: Engineering Testing and Evaluation. We provide engineering testing and evaluation of PV products developed by companies during work sponsored by the U.S. Department of Energy (DOE). We determine if products meet performance criteria established by DOE for a company's contractual obligations. Standards Development. We support the development of national and international standards. Current work includes investigating methods of preconditioning cadmium telluride and copper indium gallium diselenide PV modules so that when they are tested for reporting conditions, the results are correlated with subsequent field measurements.

285

Optimized hydrogen piston engines  

DOE Green Energy (OSTI)

Hydrogen piston engines can be simultaneously optimized for improved thermal efficiency and for extremely low emissions. Using these engines in constant-speed, constant-load systems such as series hybrid-electric automobiles or home cogeneration systems can result in significantly improved energy efficiency. For the same electrical energy produced, the emissions from such engines can be comparable to those from natural gas-fired steam power plants. These hydrogen-fueled high-efficiency, low-emission (HELE) engines are a mechanical equivalent of hydrogen fuel cells. HELE engines could facilitate the transition to a hydrogen fuel cell economy using near-term technology.

Smith, J.R.

1994-05-10T23:59:59.000Z

286

The Department of Mechanical Engineering --Engineering Mechanics  

E-Print Network (OSTI)

, Missile, Research, Development and Engineering Directorate's Propulsion Iaborato'. Ills primaly areas of research are in numerical combustion, and the thermal and mechanical aging ofnitrate esterpropellants decomposition and combustion. Stabilizers are added to the propellants to neutralize the decomposition products

Endres. William J.

287

ARM - Engineering Work Request & Engineering Work Order Guidelines  

NLE Websites -- All DOE Office Websites (Extended Search)

Work Request & Engineering Work Request & Engineering Work Order Guidelines Page Contents: Introduction Discussion of the ARM Climate Research Facility Engineering Process: The Engineering Change Request (ECR) and the Engineering Change Order (ECO) Operations and Engineering Task Consulting: The Engineering Work Request (EWR) and the Engineering Work Order (EWO) Relationship of the ECR/ECO and EWR/EWO to the Engineering Task Tracking Tool Relationship of the ECR/ECO and EWR/EWO to the Existing Configuration Control Process in the ARM Climate Research Facility(PIF/CAR, PRR, ORR, and BCR) Glossary Frequently Asked Questions (PDF, 173K) Engineering Work Request & Engineering Work Order Guidelines Process Guidelines for the Engineering Change Request/Engineering Change Order and Engineering Work Request/Engineering Work Order

288

Wind Engineering Information at NIST  

Science Conference Proceedings (OSTI)

NIST Home > Wind Engineering Information at NIST. Wind Engineering Information at NIST. (the links below are a compilation ...

2010-09-23T23:59:59.000Z

289

Improved accountability method for measuring enriched uranium in H-Canyon dissolver solution at the Savannah River Site  

SciTech Connect

At the Savannah River Site (SRS), accountability measurement of enriched uranium dissolved in H-Canyon is performed using isotope dilution mass spectrometry (IDMS). In the IDMS analytical method, a known quantity of uranium{sup 233} is added to the sample solution containing enriched uranium and fission products. The resulting uranium mixture must first be purified using a separation technique in the shielded analytical(``hot``) cells to lower radioactivity levels by removing fission products. Following this purification, the sample is analyzed by mass spectrometry to determine the total uranium content and isotopic abundance. The magnitude of the response of each uranium isotope in the sample solution and the response of the U{sup 233} spike is measured. By ratioing these responses, relative to the known quantity of the U{sup 233} spike, the uranium content can be determined. A hexane solvent extraction technique, used for years at SRS to remove fission products prior to the mass spectrometry analysis of uranium, has several problems. The hexone method is tedious, requires additional sample clean-up after the purified sample is removed from the shielded cells and requires the use of Resource Conservation and Recovery Act (RCRA)-listed hazardous materials (hexone and chromium compounds). A new high speed separation method that enables a rapid removal of fission products in a shielded cells environment has been developed by the SRS Central Laboratory to replace the hexone method. The new high speed column extraction chromatography technique employs applied vacuum and columns containing tri (2-ethyl-hexyl) phosphate (TEHP) solvent coated on a small particle inert support (SM-7 Bio Beads). The new separation is rapid, user friendly, eliminates the use of the RCA-listed hazardous chemicals and reduces the amount of solid waste generated by the separation method. 2 tabs. 4 figs.

Maxwell, S.L. III; Satkowski, J.; Mahannah, R.N.

1992-08-01T23:59:59.000Z

290

Improved accountability method for measuring enriched uranium in H-Canyon dissolver solution at the Savannah River Site  

SciTech Connect

At the Savannah River Site (SRS), accountability measurement of enriched uranium dissolved in H-Canyon is performed using isotope dilution mass spectrometry (IDMS). In the IDMS analytical method, a known quantity of uranium{sup 233} is added to the sample solution containing enriched uranium and fission products. The resulting uranium mixture must first be purified using a separation technique in the shielded analytical( hot'') cells to lower radioactivity levels by removing fission products. Following this purification, the sample is analyzed by mass spectrometry to determine the total uranium content and isotopic abundance. The magnitude of the response of each uranium isotope in the sample solution and the response of the U{sup 233} spike is measured. By ratioing these responses, relative to the known quantity of the U{sup 233} spike, the uranium content can be determined. A hexane solvent extraction technique, used for years at SRS to remove fission products prior to the mass spectrometry analysis of uranium, has several problems. The hexone method is tedious, requires additional sample clean-up after the purified sample is removed from the shielded cells and requires the use of Resource Conservation and Recovery Act (RCRA)-listed hazardous materials (hexone and chromium compounds). A new high speed separation method that enables a rapid removal of fission products in a shielded cells environment has been developed by the SRS Central Laboratory to replace the hexone method. The new high speed column extraction chromatography technique employs applied vacuum and columns containing tri (2-ethyl-hexyl) phosphate (TEHP) solvent coated on a small particle inert support (SM-7 Bio Beads). The new separation is rapid, user friendly, eliminates the use of the RCA-listed hazardous chemicals and reduces the amount of solid waste generated by the separation method. 2 tabs. 4 figs.

Maxwell, S.L. III; Satkowski, J.; Mahannah, R.N.

1992-01-01T23:59:59.000Z

291

Engineering Fundamentals - Civil Engineering Topics, Version 2.0  

Science Conference Proceedings (OSTI)

The Civil Engineering Topics, v2.0 module of Engineering Fundamentals provides information about basic civil engineering terms and concepts in order to identify civil engineering-related design, materials, and safety considerations, as they relate to nuclear power plant employees. It is intended for use as orientation training of new engineering support personnel.Benefits & ValueEngineering Fundamental Civil Engineering Topics will allow for the ...

2012-11-20T23:59:59.000Z

292

Staged combustion with piston engine and turbine engine supercharger  

DOE Patents (OSTI)

A combustion engine method and system provides increased fuel efficiency and reduces polluting exhaust emissions by burning fuel in a two-stage combustion system. Fuel is combusted in a piston engine in a first stage producing piston engine exhaust gases. Fuel contained in the piston engine exhaust gases is combusted in a second stage turbine engine. Turbine engine exhaust gases are used to supercharge the piston engine.

Fischer, Larry E. (Los Gatos, CA); Anderson, Brian L. (Lodi, CA); O' Brien, Kevin C. (San Ramon, CA)

2006-05-09T23:59:59.000Z

293

Staged combustion with piston engine and turbine engine supercharger  

DOE Patents (OSTI)

A combustion engine method and system provides increased fuel efficiency and reduces polluting exhaust emissions by burning fuel in a two-stage combustion system. Fuel is combusted in a piston engine in a first stage producing piston engine exhaust gases. Fuel contained in the piston engine exhaust gases is combusted in a second stage turbine engine. Turbine engine exhaust gases are used to supercharge the piston engine.

Fischer, Larry E. (Los Gatos, CA); Anderson, Brian L. (Lodi, CA); O' Brien, Kevin C. (San Ramon, CA)

2011-11-01T23:59:59.000Z

294

Generating Economic Development from a Wind Power Plant in Spanish Fork Canyon, Utah: A Case Study and Analysis of State-Level Economic Impacts  

Wind Powering America (EERE)

Generating Economic Development from a Wind Power Generating Economic Development from a Wind Power Project in Spanish Fork Canyon, Utah: A Case Study and Analysis of State-Level Economic Impacts Sandra Reategui Edwin R. Stafford, Ph.D. Cathy L. Hartman, Ph.D. Center for the Market Diffusion of Renewable Energy and Clean Technology Jon M. Huntsman School of Business Utah State University 3560 Old Main Hill Logan, Utah 84322-3560 January 2009 DOE/GO-102009-2760 Acknowledgements ....................................................................................................................... 1 Introduction ................................................................................................................................... 2 Report Overview ......................................................................................................................... 2

295

Engine fuels from biomass  

SciTech Connect

Methods discussed for the conversion of biomass to engine fuels include the production of producer gas, anaerobic fermentation to give biogas, fermentation of sugars and starches to give EtOH, and the production of synthesis gas for conversion to MeOH or hydrocarbons. Also discussed are the suitability of these fuels for particular engines, biomass availability, and the economics of biomass-derived engine fuels.

Parker, H.W.

1982-01-01T23:59:59.000Z

296

Tools for Engineered Surfaces  

Science Conference Proceedings (OSTI)

... Heat Exchangers, Steam Condensers. 2636.3, 216, 21,000. ... Turbines and Turbine Generator Sets, 67, 6, 4, 2. IC Engines, 263, 19, 8, 4. ...

2011-10-19T23:59:59.000Z

297

Documents: Engineering Studies  

NLE Websites -- All DOE Office Websites (Extended Search)

of Depleted UF6 99 KB details HTML Icon Preconceptual Design Studies and Cost Data of Depleted Uranium Hexafluoride Conversion Plants 4 KB details Engineering Analysis Report...

298

Engineering Salary Trends  

Science Conference Proceedings (OSTI)

Salaries of Engineers in Education 1994 reports salaries of full-time faculty at ... to earn higher salaries at medium-sized companies (500-4,999 employees),...

299

Search engine credibility.  

E-Print Network (OSTI)

??While search engines have become increasingly popular over the past years, little research is concerned with how they attend to credibility. Through interviews with six (more)

Floden, Asbjrn

2005-01-01T23:59:59.000Z

300

Internal combustion engine  

SciTech Connect

An improvement to an internal combustion engine is disclosed that has a fuel system for feeding a fuel-air mixture to the combustion chambers and an electrical generation system, such as an alternator. An electrolytic cell is attached adjacent to the engine to generate hydrogen and oxygen upon the application of a voltage between the cathode and anode of the electrolytic cell. The gas feed connects the electrolytic cell to the engine fuel system for feeding the hydrogen and oxygen to the engine combustion chambers. Improvements include placing the electrolytic cell under a predetermined pressure to prevent the electrolyte from boiling off, a cooling system for the electrolytic cell and safety features.

Valdespino, J.M.

1981-06-09T23:59:59.000Z

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

LNG Engine Delivery  

This is a method of improved delivery of liquid natural gas (LNG) within an engine delivery system. The LNG gas is first be pumped into the insulated ...

302

NASA and Green Engineering  

Science Conference Proceedings (OSTI)

... First course offered in January 2011; 5 offerings so far. 12. Sponsors: Office of the Chief Engineer and Environmental Management Div. ...

2012-01-21T23:59:59.000Z

303

Improving Search Engine Reliability  

Science Conference Proceedings (OSTI)

Search engines on the Internet are used daily to access and find information. While these services are providing an easy way to find information globally

Jyoti Pruthi; Ela Kumar

2010-01-01T23:59:59.000Z

304

Biosystems Engineering, 1 edition  

Science Conference Proceedings (OSTI)

Maximize productivity while minimizing environmental impactDevelop sustainable products, energy sources, and processes using the concepts and methods contained in this interdisciplinary resource. Biosystems Engineering discusses ...

Ahindra Nag

2009-08-01T23:59:59.000Z

305

Stirling Engine Cycle Efficiency.  

E-Print Network (OSTI)

??ABSTRACT This study strives to provide a clear explanation of the Stirling engine and its efficiency using new automation technology and the Lab View software. (more)

Naddaf, Nasrollah

2012-01-01T23:59:59.000Z

306

Engineering Science at NERSC  

NLE Websites -- All DOE Office Websites (Extended Search)

Engineering Science Bell1.png Researchers in this area develop and apply a variety of advanced computational methodologies for solving large-scale complex fluid flow problems with...

307

Diesel Engine Alternatives  

DOE Green Energy (OSTI)

There are basically three different modes of combustion possible for use in reciprocating engines. These include, diffusion burning, as occurs in current diesel engines, flame propagation combustion such as used in conventional SI engines, and homogeneous combustion such as is used in the SwRI HCCI engine. Diesel engines currently offer significant fuel consumption benefits relative to other powerplants for on and off road applications; however, costs and efficiency may become problems as the emissions standards become even more stringent. This presentation presents a discussion of the potentials of HCCI and flame propagation engines as alternatives to the diesel engines. It is suggested that as the emissions standards become more and more stringent, the advantages of the diesel may disappear. The potential for HCCI is limited by the availability of the appropriate fuel. The potential of flame propagation engines is limited by several factors including knock, EGR tolerance, high BMEP operation, and throttling. These limitations are discussed in the context of potential for improvement of the efficiency of the flame propagation engine.

Ryan, T

2003-08-24T23:59:59.000Z

308

Stirling engine heating system  

SciTech Connect

A hot gas engine is described wherein a working gas flows back and forth in a closed path between a relatively cooler compression cylinder side of the engine and a relatively hotter expansion cylinder side of the engine and the path contains means including a heat source and a heat sink acting upon the gas in cooperation with the compression and expansion cylinders to cause the gas to execute a thermodynamic cycle wherein useful mechanical output power is developed by the engine, the improvement in the heat source which comprises a plurality of individual tubes each forming a portion of the closed path for the working gas.

Johansson, L.N.; Houtman, W.H.; Percival, W.H.

1988-06-28T23:59:59.000Z

309

Bioinspired Materials Engineering  

Science Conference Proceedings (OSTI)

Bioinspired Crystal Growth by Organic/Inorganic Crystal Engineering Bioinspired Materials Design from Renewable Resources Biological Synthesis of TiNi...

310

NREL: Systems Engineering - Workshops  

NLE Websites -- All DOE Office Websites (Extended Search)

Workshops The Wind Energy Systems Engineering Workshop is a biennial workshop that invites speakers from academia, industry, and international research laboratories to discuss...

311

Free piston stirling engines  

SciTech Connect

This book presents a basic introduction to free piston Stirling engine technology through a review of specialized background material. It also includes information based on actual construction and operation experience with these machines, as well as theoretical and analytical insights into free piston Stirling engine technology.

Walker, C.

1985-01-01T23:59:59.000Z

312

COLLEGE OF ENGINEERING Environment  

E-Print Network (OSTI)

.D. degrees in electrical engineering from Colorado State, has made pioneering contributions in the area at a semiconductor company as a designer prior to starting her Ph.D. program in electrical engineering at Colorado solutions they apply to, Colorado State continues to develop itself as the "Green University," which gives

313

Hydrogen Fuel Cell Engines  

E-Print Network (OSTI)

#12;#12;Hydrogen Fuel Cell Engines MODULE 11:GLOSSARY AND CONVERSIONS CONTENTS 11.1 GLOSSARY Cell Engines MODULE 11:GLOSSARY AND CONVERSIONS OBJECTIVES This module is for reference only. Hydrogen MODULE 11: GLOSSARY AND CONVERSIONS PAGE 11-1 11.1 Glossary This glossary covers words, phrases

314

Gas turbine engines  

SciTech Connect

A core engine or gas generator is described for use in a range of gas turbine engines. A multi-stage compressor and a single stage supersonic turbine are mounted on a single shaft. The compressor includes a number of stages of variable angle and the gas generator has an annular combustion chamber.

MacDonald, A.G.

1976-05-18T23:59:59.000Z

315

Mining engineering analysis  

SciTech Connect

An attempt is made to fill the gap between theory and application in mining engineering. The book is based on SME Mining Engineering Handbook and the Coal Mining Technology - Theory and Practice. Each chapter deals with the theory and then presents problems of applications and the solutions to them. Topics considered include underground mining, surface mining, geophysics, mining equipment, and rock mechanics.

Bise, C.J.

1986-01-01T23:59:59.000Z

316

CHEMICAL AND PAPER ENGINEERING  

E-Print Network (OSTI)

SAFETY HANDBOOK For CHEMICAL AND PAPER ENGINEERING 2010-2011 #12;Page 1 Safety Guidelines Department of Chemical and Paper Engineering Miami University - Oxford, Ohio 45056 The following safety and Laboratory Coordinator Responsibilities III. Emergency Procedures IV. Chemical Storage V. Routine

Dollar, Anna

317

Stirling engine piston ring  

DOE Patents (OSTI)

A piston ring design for a Stirling engine wherein the contact pressure between the piston and the cylinder is maintained at a uniform level, independent of engine conditions through a balancing of the pressure exerted upon the ring's surface and thereby allowing the contact pressure on the ring to be predetermined through the use of a preloaded expander ring.

Howarth, Roy B. (Clifton Park, NY)

1983-01-01T23:59:59.000Z

318

Stirling engine piston ring  

SciTech Connect

A piston ring design for a Stirling engine wherein the contact pressure between the piston and the cylinder is maintained at a uniform level, independent of engine conditions through a balancing of the pressure exerted upon the ring's surface and thereby allowing the contact pressure on the ring to be predetermined through the use of a preloaded expander ring.

Howarth, Roy B. (Clifton Park, NY)

1983-01-01T23:59:59.000Z

319

Computer Science & Computer Engineering  

E-Print Network (OSTI)

CSCE Computer Science & Computer Engineering #12;Computer scientists and computer engineers design and implement e cient software and hardware solutions to computer-solvable problems. They are involved, virtual reality and robotics. Within the Computer Science department, we o er four exciting majors from

Rohs, Remo

320

College of Engineering CME Chemical Engineering  

E-Print Network (OSTI)

550andengineeringstanding. CME 462 PROCESS CONTROL. (3) Basic theory of automatic control devices. Technologies covered include coal, natural gas, nuclear, biomass, wind, solar and advanced technologies. Prereq: Engineering standing or consent of instructor. (Same as EGR 542.) CME 550 CHEMICAL REACTOR DESIGN. (3

Kim, Mi-Ok

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Metabolic Engineering VII Conference  

SciTech Connect

The aims of this Metabolic Engineering conference are to provide a forum for academic and industrial researchers in the field; to bring together the different scientific disciplines that contribute to the design, analysis and optimization of metabolic pathways; and to explore the role of Metabolic Engineering in the areas of health and sustainability. Presentations, both written and oral, panel discussions, and workshops will focus on both applications and techniques used for pathway engineering. Various applications including bioenergy, industrial chemicals and materials, drug targets, health, agriculture, and nutrition will be discussed. Workshops focused on technology development for mathematical and experimental techniques important for metabolic engineering applications will be held for more in depth discussion. This 2008 meeting will celebrate our conference tradition of high quality and relevance to both industrial and academic participants, with topics ranging from the frontiers of fundamental science to the practical aspects of metabolic engineering.

Kevin Korpics

2012-12-04T23:59:59.000Z

322

Thermoacoustic engines and refrigerators  

SciTech Connect

This report is a transcript of a practice lecture given in preparation for a review lecture on the operation of thermoacoustic engines and refrigerators. The author begins by a brief review of the thermodynamic principles underlying the operation of thermoacoustic engines and refrigerators. Remember from thermodynamics class that there are two kinds of heat engines, the heat engine or the prime mover which produces work from heat, and the refrigerator or heat pump that uses work to pump heat. The device operates between two thermal reservoirs at temperatures T{sub hot} and T{sub cold}. In the heat engine, heat flows into the device from the reservoir at T{sub hot}, produces work, and delivers waste heat into the reservoir at T{sub cold}. In the refrigerator, work flows into the device, lifting heat Q{sub cold} from reservoir at T{sub cold} and rejecting waste heat into the reservoir at T{sub hot}.

Swift, G.

1996-12-31T23:59:59.000Z

323

An introductory software engineering course for software engineering program  

Science Conference Proceedings (OSTI)

One important issue in undergraduate software engineering curriculum is how to help students establish the concept of software engineering at the beginning of software engineering undergraduate program and to provide a reasonable basis of knowledge and ...

Dong Shao; Bin Luo; Eryu Ding; Qin Liu

2011-05-01T23:59:59.000Z

324

FEASIBILITY STUDY FOR THE DEVELOPMENT OF A TEST BED PROGRAM FOR NOVEL DETECTORS AND DETECTOR MATERIALS AT SRS H-CANYON SEPARATIONS FACILITY  

Science Conference Proceedings (OSTI)

Researchers at the Savannah River National Laboratory (SRNL) have proposed that a test bed for advanced detectors be established at the H-Canyon separations facility located on the DOE Savannah River Site. The purpose of the proposed test bed will be to demonstrate the capabilities of emerging technologies for national and international safeguards applications in an operational environment, and to assess the ability of proven technologies to fill any existing gaps. The need for such a test bed has been expressed in the National Nuclear Security Administration's (NNSA) Next Generation Safeguards Initiative (NGSI) program plan and would serve as a means to facilitate transfer of safeguards technologies from the laboratory to an operational environment. New detectors and detector materials open the possibility of operating in a more efficient and cost effective manner, thereby strengthening national and international safeguards objectives. In particular, such detectors could serve the DOE and IAEA in improving timeliness of detection, minimizing uncertainty and improving confidence in results. SRNL's concept for the H Canyon test bed program would eventually open the facility to other DOE National Laboratories and establish a program for testing national and international safeguards related equipment. The initial phase of the test bed program is to conduct a comprehensive feasibility study to determine the benefits and challenges associated with establishing such a test bed. The feasibility study will address issues related to the planning, execution, and operation of the test bed program. Results from the feasibility study will be summarized and discussed in this paper.

Sexton, L.; Mendez-Torres, A.; Hanks, D.

2011-06-07T23:59:59.000Z

325

Revised financial analysis of experimental releases conducted at Glen Canyon Dam during water years 1997 through 2005.  

Science Conference Proceedings (OSTI)

Because of concerns about the impact that Glen Canyon Dam (GCD) operations were having on downstream ecosystems and endangered species, the Bureau of Reclamation (Reclamation) conducted an Environmental Impact Statement (EIS) on dam operations (DOE 1996). New operating rules and management goals for GCD that had been specified in the Record of Decision (ROD) (Reclamation 1996) were adopted in February 1997. In addition to issuing new operating criteria, the ROD mandated experimental releases for the purpose of conducting scientific studies. This paper examines the financial implications of the experimental flows that were conducted at the GCD from 1997 to 2005. An experimental release may have either a positive or negative impact on the financial value of energy production. This study estimates the financial costs of experimental releases, identifies the main factors that contribute to these costs, and compares the interdependencies among these factors. An integrated set of tools was used to compute the financial impacts of the experimental releases by simulating the operation of the GCD under two scenarios, namely, (1) a baseline scenario that assumes operations comply with the ROD operating criteria and experimental releases that actually took place during the study period, and (2) a 'without experiments' scenario that is identical to the baseline scenario of operations that comply with the GCD ROD, except it assumes that experimental releases did not occur. The Generation and Transmission Maximization (GTMax) model was the main simulation tool used to dispatch GCD and other hydropower plants that comprise the Salt Lake City Area Integrated Projects (SLCA/IP). Extensive data sets and historical information on SLCA/IP power plant characteristics, hydrologic conditions, and Western Area Power Administration's (Western's) power purchase prices were used for the simulation. In addition to estimating the financial impact of experimental releases, the GTMax model was also used to gain insights into the interplay among ROD operating criteria, exceptions that were made to criteria to accommodate the experimental releases, and Western operating practices. Experimental releases in some water years resulted in financial benefits to Western whileothers resulted in financial costs. During the study period, the total financial costs of all experimental releases were more than $23 million.

Veselka, T. D.; Poch, L. A.; Palmer, C. S.; Loftin, S.; Osiek, B.; Decision and Information Sciences; Western Area Power Administration, Colorado River Storage Project Management Center

2011-01-11T23:59:59.000Z

326

WEB RESOURCE: Nuclear Engineering Materials - TMS  

Science Conference Proceedings (OSTI)

Feb 12, 2007 ... "Nuclear Engineering Materials." Engineering Physics Department, College of Engineering. University of Wisconsin-Madison, Fall 2006.

327

Toward Integrated Life-limit Materials Engineering of Turbine Engine ...  

Science Conference Proceedings (OSTI)

... the design and life management of future turbine engine rotor alloys and components. ... loading variables found in the operation of advanced turbine engines.

328

Engineering Fundamentals - Mechanical Engineering Topics, Version 4.0  

Science Conference Proceedings (OSTI)

The Mechanical Engineering module covers basic terms and concepts of mechanical engineering and discusses their applications in nuclear power plants. This course will ...

2013-01-17T23:59:59.000Z

329

CHEMICAL ENGINEERING AT McGILL Bachelor of Engineering in Chemical Engineering  

E-Print Network (OSTI)

CHEMICAL ENGINEERING AT McGILL Bachelor of Engineering in Chemical Engineering What is chemical engineering? Chemical engineers design processes and systems that produce everything from plastics and paper to pharmaceuticals, processed foods and advanced materials.What a chemist might produce in a test tube, chemical

Barthelat, Francois

330

COMPUTER ENGINEERING AT McGILL Bachelor of Engineering in Computer Engineering  

E-Print Network (OSTI)

COMPUTER ENGINEERING AT McGILL Bachelor of Engineering in Computer Engineering What is computer engineering? It's almost impossible to imagine our contemporary world without computer technology. Almost on computers in some form or another, and computer engineers make it all possible.They design and develop

Barthelat, Francois

331

The Breadth of Mechanical Engineering  

E-Print Network (OSTI)

;Industrial Engineering Industrial Economics Engineering Statistics Quality Control Cost and Time Estimating Astronautics Traffic Engineering #12;Building Construction and Equipment Planning and Contracts Structural Processes Foundry Metal Working Plastics Welding Material Removal Surface-Texture Control #12;Pumps

Fabrikant, Sara Irina

332

Mechanical, Aerospace and Civil Engineering  

E-Print Network (OSTI)

and Technology (IET); the Chartered Institution of Building Services Engineers (CIBSE), and the Energy Institute Institution of Building Services Engineers (CIBSE) The Energy Institute (EI) Institution of Civil Engineers

Heil, Matthias

333

E85 Optimized Engine  

SciTech Connect

A 5.0L V8 twin-turbocharged direct injection engine was designed, built, and tested for the purpose of assessing the fuel economy and performance in the F-Series pickup of the Dual Fuel engine concept and of an E85 optimized FFV engine. Additionally, production 3.5L gasoline turbocharged direct injection (GTDI) ??EcoBoost? engines were converted to Dual Fuel capability and used to evaluate the cold start emissions and fuel system robustness of the Dual Fuel engine concept. Project objectives were: to develop a roadmap to demonstrate a minimized fuel economy penalty for an F-Series FFV truck with a highly boosted, high compression ratio spark ignition engine optimized to run with ethanol fuel blends up to E85; to reduce FTP 75 energy consumption by 15% - 20% compared to an equally powered vehicle with a current production gasoline engine; and to meet ULEV emissions, with a stretch target of ULEV II / Tier II Bin 4. All project objectives were met or exceeded.

Stanley Bower

2011-12-31T23:59:59.000Z

334

Principles of models based engineering  

SciTech Connect

This report describes a Models Based Engineering (MBE) philosophy and implementation strategy that has been developed at Los Alamos National Laboratory`s Center for Advanced Engineering Technology. A major theme in this discussion is that models based engineering is an information management technology enabling the development of information driven engineering. Unlike other information management technologies, models based engineering encompasses the breadth of engineering information, from design intent through product definition to consumer application.

Dolin, R.M.; Hefele, J.

1996-11-01T23:59:59.000Z

335

Heavy Truck Engine Program  

DOE Green Energy (OSTI)

The Heavy Duty Truck Engine Program at Cummins embodied three significant development phases. All phases of work strove to demonstrate a high level of diesel engine efficiency in the face of increasingly stringent emission requirements. Concurrently, aftertreatment system development and refinement was pursued in support of these efficiency demonstrations. The program's first phase focused on the demonstration in-vehicle of a high level of heavy duty diesel engine efficiency (45% Brake Thermal Efficiency) at a typical cruise condition while achieving composite emissions results which met the 2004 U.S. EPA legislated standards. With a combination of engine combustion calibration tuning and the development and application of Urea-based SCR and particulate aftertreatment, these demonstrations were successfully performed by Q4 of 2002. The second phase of the program directed efforts towards an in-vehicle demonstration of an engine system capable of meeting 2007 U.S. EPA legislated emissions requirements while achieving 45% Brake Thermal Efficiency at cruise conditions. Through further combustion optimization, the refinement of Cummins Cooled EGR architecture, the application of a high pressure common rail fuel system and the incorporation of optimized engine parasitics, Cummins Inc. successfully demonstrated these deliverables in Q2 of 2004. The program's final phase set a stretch goal of demonstrating 50% Brake Thermal Efficiency from a heavy duty diesel engine system capable of meeting 2010 U.S. EPA legislated emissions requirements. Cummins chose to pursue this goal through further combustion development and refinement of the Cooled EGR system architecture and also applied a Rankine cycle Waste Heat Recovery technique to convert otherwise wasted thermal energy to useful power. The engine and heat recovery system was demonstrated to achieve 50% Brake Thermal Efficiency while operating at a torque peak condition in second quarter, 2006. The 50% efficient engine system was capable of meeting 2010 emissions requirements through the application of NOx and particulate matter reduction techniques proven earlier in the program.

Nelson, Christopher

2009-01-08T23:59:59.000Z

336

Chemical Engineering | More Science | ORNL  

NLE Websites -- All DOE Office Websites (Extended Search)

Chemical and Engineering Materials Clean Energy Nuclear Sciences Computer Science Earth and Atmospheric Sciences Materials Science and Engineering Mathematics Physics More Science Home | Science & Discovery | More Science | Engineering SHARE Engineering Engineering at ORNL is integrated with nearly all of the scientific research areas and user facilities. In particular, ORNL has core capabilities chemical engineering and systems engineering. Chemical engineering moves knowledge gained from fundamental chemical research toward applications. For example, this capability supports the development of fuel reprocessing techniques and enables radioisotope production, isotope separation, and development of isotope applications. This capacity also contributes to advances in energy efficiency, renewable

337

NREL: Wind Research - Systems Engineering  

NLE Websites -- All DOE Office Websites (Extended Search)

Computer-Aided Engineering Systems Engineering Controls Analysis Testing Utility Grid Integration Assessment Wind Resource Assessment Projects Facilities Research Staff Working...

338

SC e-journals, Engineering  

Office of Scientific and Technical Information (OSTI)

Engineering Engineering ACM Transactions on Design Automation of Electronic Systems (TODAES) ACM Transactions on Embedded Computing Systems (TECS) ACS Nano Acta Mechanica Acta Mechanica Sinica Adsorption Advanced Engineering Materials Advanced Powder Technology Advanced Robotics Advances in Computational Mathematics Advances In Engineering Software Advances in Materials Science and Engineering - OAJ Advances in Mathematical Engineering - OAJ Advances in Optics and Photonics AlChE Journal Algorithmica American Journal of Engineering and Applied Sciences - OAJ Analog Integrated Circuits and Signal Processing Annals of Nuclear Energy Annual Review of Fluid Mechanics Annual Review of Materials Research Applicable Algebra in Engineering, Communication and Computing Applied Composite Materials

339

Engines, turbines and compressors directory  

SciTech Connect

This book is a directory of engines, turbines and compressors. It adds and deletes compressor engines in use by the gas industry.

1989-01-01T23:59:59.000Z

340

Sandia National Laboratories Encryption Engine  

engine pipeline full so that the encryption engine can run at full capacity in CBC mode or other encryption modes requiring feedback from previous ...

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Windward Engineering | Open Energy Information  

Open Energy Info (EERE)

"Windward Engineering" Retrieved from "http:en.openei.orgwindex.php?titleWindwardEngineering&oldid353118" Categories: Clean Energy Organizations Companies Organizations...

342

Spring Canyon RIVERVALLEY  

E-Print Network (OSTI)

Qal Qaf Qaf Qaf Qaf Tcl Qaf Qal Pzrm Qaf Qaf Qaf Pzrm Tog Tcc Tcu Qaf Ts Pzlc Ts Qal Tcu Pzrm Pzrm Ts Jgr Qaf Qaf Pzo Ts Qaf Tcl Pzrm Pzrm Qal Qaf Ts Tcc Tcl Tad Pzrm Tcs Tcs? Pzrm Qp Pzlc Ts Pzrm Qaf Tcl Qaf Tcu Tcl Tcl Tcs Tcs Tb Pzrm Tbm Tcic Ts? Tcs Tcu Pzrm Pzrm Tcu Pzlc Tcc Tcu Tad Pzrm Tct Qaf Tcic

Tingley, Joseph V.

343

VALUE ENGINEERING.PDF  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6 6 I N S P E C T I O N R E P O R T U.S. DEPARTMENT OF ENERGY OFFICE OF INSPECTOR GENERAL OFFICE OF INSPECTIONS FOLLOW-ON INSPECTION OF THE DEPARTMENT OF ENERGY'S VALUE ENGINEERING PROGRAM DECEMBER 2001 U.S. DEPARTMENT OF ENERGY Washington, DC 20585 December 20, 2001 MEMORANDUM FOR THE SECRETARY FROM: Gregory H. Friedman /s/ Inspector General SUBJECT: INFORMATION: Report on "Follow-on Inspection of the Department of Energy's Value Engineering Program" BACKGROUND Value Engineering is a recognized management tool which, if properly implemented and executed, can streamline operations, improve quality, and reduce costs. Through the use of methodologies such as Value Engineering, Federal agencies are realizing an average of more than $20 in savings/costs avoidance for each dollar spent on performing the value effort.

344

Director for Engineering  

E-Print Network (OSTI)

Electrical Systems Design Fire Alarm Systems Audio/Video Systems Energy Analysis Power & Light Analysis Cordero Manager for Architectural Services Jeff Sutherland, AIA Manager for Electrical Engineering David Contract Management Construction Inspection HVAC Design Plumbing Design Fire Suppression System Energy

Zhang, Yuanlin

345

Omnivorous Engine Project  

NLE Websites -- All DOE Office Websites (Extended Search)

The new U.S. Renewable Fuel The new U.S. Renewable Fuel Standard requires that the production of ethanol and advanced biofuels be increased to 36 billion gallons by 2022. The production of ethanol will be capped at 15 billion gallons, leaving 21 billion gallons to come from other sources such as bio-butanol. While current flex-fuel engines are designed and calibrated to use gasoline, they do not take full advantage of the specific beneficial properties of alternative fuels and do not operate at maximum efficiency. Argonne's Approach Argonne's Center for Transportation Research set up a dedicated test engine for alternative fuels research. Its key features are: * State-of-the-art engine test cell with low- and high-speed data acquisition * Modern, fully-instrumented 4-cylinder direct-injection engine

346

Department Of Engineering.  

E-Print Network (OSTI)

& Engineering Materials for nuclear energy system, fission reactors, nuclear fuels, energy policy solidification; microgravity processing. Xudong Wang Assistant Professor, Materials Sci & Eng Nanomaterials and photoelectrochemical devices; nanomaterials for energy storage; nanoelectronics; nano-biomaterials. Jay Samuel Senior

Li, Yi

347

Displacer for Stirling engine  

SciTech Connect

In a Stirling engine and the like, a displacer piston having a plurality of internal baffles and insulation so as to prevent undesired heat transfer across the displacer piston.

Brown, A. T.

1985-12-24T23:59:59.000Z

348

Engineering secure software  

E-Print Network (OSTI)

In recent years computer software has gained notoriety for the endemic nature of security problems in software. These problems have been exploited with malicious intent by attackers. Most attempts at fixing these problems have been after-the-fact fixes in the form of software patches. The root causes for security problems in software are explored. A survey of research attempts at engineering secure software is presented. The techniques discussed range from those that are very similar to classical software engineering, to those that may be used in analyses of security requirements, as well as tools that can help engineer secure software. The survey classifies the approaches as process-oriented and as tools-oriented. The current approaches are incomplete in nature. They seem to address the security problem in parts and not in the whole. A comprehensive methodology, integrated with evolutionary software engineering practices is presented. The methodology combines both process and tools oriented approaches to construct secure software.

Jetly, Prateek

2001-01-01T23:59:59.000Z

349

Metabolic Engineering VII Conference  

DOE Green Energy (OSTI)

This 2008 meeting will celebrate our conference tradition of high quality and relevance to both industrial and academic participants, with topics ranging from the frontiers of fundamental science to the practical aspects of metabolic engineering.

Kevin Korpics

2012-12-04T23:59:59.000Z

350

Engineering responses to pandemics  

Science Conference Proceedings (OSTI)

Focusing on pandemic influenza, this chapter approaches the planning for and response to such a major worldwide health event as a complex engineering systems problem. Action-oriented analysis of pandemics requires a broad inclusion of academic disciplines ...

Richard C. Larson; Karima R. Nigmatulina

2009-01-01T23:59:59.000Z

351

NGNP Engineering Status  

SciTech Connect

The objectives of Phase 1 Engineering and Design scope are to: 1) complete the initial design activities for a prototype nuclear reactor and plant that is capable of co-generating electricity, hydrogen, and process heat; 2) identify technological aspects of the NGNP that need further advancement by research and development activities; and 3) provide engineering support to the early licensing process, including technical input to white papers and developing the basis for future safety analyses.

John Collins

2010-08-01T23:59:59.000Z

352

Liquid metal thermoacoustic engine  

DOE Green Energy (OSTI)

We are studying a liquid metal thermoacoustic engine both theoretically and experimentally. This type of engine promises to produce large quantities of electrical energy from heat at modest efficiency with no moving parts. A sound wave is usually thought of as consisting of pressure oscillations, but always attendant to the pressure oscillation are temperature oscillations. The combination produces a rich variety of ''thermoacoustic'' effects. These effects are usually so small that they are never noticed in everyday life; nevertheless under the right circumstances they can be harnessed to produce powerful heat engines, heat pumps, and refrigerators. In our liquid metal thermoacoustic engine, heat flow from a high temperature source to a low temperature sink generates a high-amplitude standing acoustic wave in liquid sodium. This acoustic power is converted to electric power by a simple magnetohydrodynamic effect at the acoustic oscillation frequency. We have developed a detailed thermoacoustic theory applicable to this engine, and find that a reasonably designed liquid sodium engine operating between 700/sup 0/C and 100/sup 0/C should generate about 60 W/cm/sup 2/ of acoustic power at about 1/3 of Carnot's efficiency. Construction of a 3000 W-thermal laboratory model engine has just been completed, and we have exciting preliminary experimental results as of the time of preparation of this manuscript showing, basically, that the engine works. We have also designed and built a 1 kHz liquid sodium magnetohydrodynamic generator and have extensive measurements on it. It is now very well characterized both experimentally and theoretically. The first generator of its kind, it already converts acoustic power to electric power with 40% efficiency. 16 refs., 5 figs.

Swift, G.W.; Migliori, A.; Wheatley, J.C.

1986-01-01T23:59:59.000Z

353

Stirling engine power control  

DOE Patents (OSTI)

A power control method and apparatus for a Stirling engine including a valved duct connected to the junction of the regenerator and the cooler and running to a bypass chamber connected between the heater and the cylinder. An oscillating zone of demarcation between the hot and cold portions of the working gas is established in the bypass chamber, and the engine pistons and cylinders can run cold.

Fraser, James P. (Scotia, NY)

1983-01-01T23:59:59.000Z

354

Diesel Engine Analysis Guide  

Science Conference Proceedings (OSTI)

This guide provides a thorough background on diesel engine analysis including combustion, vibration, and ultrasonic analysis theory. Interpretation of results is also provided. This guide is intended to enable nuclear utility personnel to make informed decisions regarding the nature and use of diesel engine analysis, including how to set up an effective program, how to establish analysis guidelines, how to make use of the resulting data to plan maintenance, determine the causes of off-design operating co...

1997-10-09T23:59:59.000Z

355

FAMU-FSU College of Engineering Department of Mechanical Engineering  

E-Print Network (OSTI)

a conventional power cycle, for example, through a steam turbine or Stirling engine. Four main elements

Krothapalli, Anjaneyulu

356

Plant Support Engineering: Generic Handbook for New System Engineers  

Science Conference Proceedings (OSTI)

In view of the demographics of todays nuclear plant system engineering organizations, newly hired and often inexperienced engineers are frequently assigned positions as system engineers. System engineering and training organizations are challenged with efficiently and effectively developing these individuals as expeditiously as possible.

2011-04-26T23:59:59.000Z

357

Intrinsically irreversible heat engine  

DOE Patents (OSTI)

A class of heat engines based on an intrinsically irreversible heat transfer process is disclosed. In a typical embodiment the engine comprises a compressible fluid that is cyclically compressed and expanded while at the same time being driven in reciprocal motion by a positive displacement drive means. A second thermodynamic medium is maintained in imperfect thermal contact with the fluid and bears a broken thermodynamic symmetry with respect to the fluid. The second thermodynamic medium is a structure adapted to have a low fluid flow impedance with respect to the compressible fluid, and which is further adapted to be in only moderate thermal contact with the fluid. In operation, thermal energy is pumped along the second medium due to a phase lag between the cyclical heating and cooling of the fluid and the resulting heat conduction between the fluid and the medium. In a preferred embodiment the engine comprises an acoustical drive and a housing containing a gas which is driven at a resonant frequency so as to be maintained in a standing wave. Operation of the engine at acoustic frequencies improves the power density and coefficient of performance. The second thermodynamic medium can be coupled to suitable heat exchangers to utilize the engine as a simple refrigeration device having no mechanical moving parts. Alternatively, the engine is reversible in function so as to be utilizable as a prime mover by coupling it to suitable sources and sinks of heat. 11 figs.

Wheatley, J.C.; Swift, G.W.; Migliori, A.

1984-12-25T23:59:59.000Z

358

Multiphase Stirling Engines  

E-Print Network (OSTI)

Analysis, design, fabrication, and experimental assessment of a symmetric three-phase free-piston Stirling engine system is discussed in this paper. The system is designed to operate with moderate-temperature heat input that is consistent with solar-thermal collectors. Diaphragm pistons and nylon flexures are considered for this prototype to eliminate surface friction and to provide appropriate seals. In addition, low loss diaphragm pistons, etched and woven-wire screen heat exchangers, and plastic flexures, as the main components of the system, are outlined. The experimental results are presented and compared with design analysis. Experiments successfully confirm the design models for heat exchanger flow friction losses and gas spring hysteresis dissipation. Furthermore, it is revealed that gas spring hysteresis loss is an important dissipation phenomenon for low-power Stirling engines and should be carefully addressed in design. Analysis shows that the gas hysteresis dissipation is reduced drastically by increasing the number of phases in a multiphase Stirling engine system. It is further shown that for an even number of phases, half of the engine chambers could be eliminated by utilizing a reversing mechanism within the multiphase system. The mathematical formulation and modal analysis of multiphase Stirling engine system are then extended to a system that incorporates a reverser. By introducing a reverser to the fabricated prototype, the system successfully operates in engine mode. The system proves its self-starting capability and validates the computed start-up temperature. ?DOI: 10.1115/1.3097274? 1

Artin Der Minassians; Seth R. Sanders

2009-01-01T23:59:59.000Z

359

Intrinsically irreversible heat engine  

DOE Patents (OSTI)

A class of heat engines based on an intrinsically irreversible heat transfer process is disclosed. In a typical embodiment the engine comprises a compressible fluid that is cyclically compressed and expanded while at the same time being driven in reciprocal motion by a positive displacement drive means. A second thermodynamic medium is maintained in imperfect thermal contact with the fluid and bears a broken thermodynamic symmetry with respect to the fluid. The second thermodynamic medium is a structure adapted to have a low fluid flow impedance with respect to the compressible fluid, and which is further adapted to be in only moderate thermal contact with the fluid. In operation, thermal energy is pumped along the second medium due to a phase lag between the cyclical heating and cooling of the fluid and the resulting heat conduction between the fluid and the medium. In a preferred embodiment the engine comprises an acoustical drive and a housing containing a gas which is driven at a resonant frequency so as to be maintained in a standing wave. Operation of the engine at acoustic frequencies improves the power density and coefficient of performance. The second thermodynamic medium can be coupled to suitable heat exchangers to utilize the engine as a simple refrigeration device having no mechanical moving parts. Alternatively, the engine is reversible in function so as to be utilizable as a prime mover by coupling it to suitable sources and sinks of heat.

Wheatley, J.C.; Swift, G.W.; Migliori, A.

1984-01-01T23:59:59.000Z

360

Engine Removal Projection Tool  

DOE Green Energy (OSTI)

The US Navy has over 3500 gas turbine engines used throughout the surface fleet for propulsion and the generation of electrical power. Past data is used to forecast the number of engine removals for the next ten years and determine engine down times between removals. Currently this is done via a FORTRAN program created in the early 1970s. This paper presents results of R&D associated with creating a new algorithm and software program. We tested over 60 techniques on data spanning 20 years from over 3100 engines and 120 ships. Investigated techniques for the forecast basis including moving averages, empirical negative binomial, generalized linear models, Cox regression, and Kaplan Meier survival curves, most of which are documented in engineering, medical and scientific research literature. We applied those techniques to the data, and chose the best algorithm based on its performance on real-world data. The software uses the best algorithm in combination with user-friendly interfaces and intuitively understandable displays. The user can select a specific engine type, forecast time period, and op-tempo. Graphical displays and numerical tables present forecasts and uncertainty intervals. The technology developed for the project is applicable to other logistic forecasting challenges.

Ferryman, Thomas A.; Matzke, Brett D.; Wilson, John E.; Sharp, Julia L.; Greitzer, Frank L.

2005-06-02T23:59:59.000Z

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Intrinsically irreversible heat engine  

DOE Patents (OSTI)

A class of heat engines based on an intrinsically irreversible heat transfer process is disclosed. In a typical embodiment the engine comprises a compressible fluid that is cyclically compressed and expanded while at the same time being driven in reciprocal motion by a positive displacement drive means. A second thermodynamic medium is maintained in imperfect thermal contact with the fluid and bears a broken thermodynamic symmetry with respect to the fluid. the second thermodynamic medium is a structure adapted to have a low fluid flow impedance with respect to the compressible fluid, and which is further adapted to be in only moderate thermal contact with the fluid. In operation, thermal energy is pumped along the second medium due to a phase lag between the cyclical heating and cooling of the fluid and the resulting heat conduction between the fluid and the medium. In a preferred embodiment the engine comprises an acoustical drive and a housing containing a gas which is driven at a resonant frequency so as to be maintained in a standing wave. Operation of the engine at acoustic frequencies improves the power density and coefficient of performance. The second thermodynamic medium can be coupled to suitable heat exchangers to utilize the engine as a simple refrigeration device having no mechanical moving parts. Alternatively, the engine is reversible in function so as to be utilizable as a prime mover by coupling it to suitable sources and sinks of heat.

Wheatley, John C. (Los Alamos, NM); Swift, Gregory W. (Los Alamos, NM); Migliori, Albert (Santa Fe, NM)

1984-01-01T23:59:59.000Z

362

Discovery of the base of the Pinal Schist and the Bear Canyon sequence below it in the eastern Metamorphic terrane of the Dos Cabezas mountains, Cochise County, Arizona  

Science Conference Proceedings (OSTI)

The eastern metamorphic terrane of the Dos Cabezas mountains is underlain by Pinal Schist (PS). Recent detailed mapping along the western edge of this terrane shows that a flat planar regional unconformity (UC) bounds this Pinal body at its western stratigraphic base. Below the UC lies 8 km[sup 2] of greenschist facies metapelites and metafelsites here given the provisional name of the Bear Canyon sequence (BCS). The PS above the UC is over 10 stratigraphic km, grading from 1 km conglomerate at the base (clasts are metafelsites and metasediments with very minor quartz and granite) up into 3 km of sandstones and then pelite, all with greenschist facies overprint. Relict bedding with abundant crossbedding is common; the sequence is upright. Foliation parallels bedding. Lineation is absent. The UC itself is well exposed in two places, on both sides of Happy Camp Canyon (HCC). On the west of HCC, the surface is exposed at the mouth of Bear Canyon (NW1/4 Sec. 31, T13S R28E) striking south and then southwest about 4 km, ending in the N center of Sec. 12, T14S R27E. The unconformity and the Pinal above it lie NS 30E in the north and smoothly swing to NE 50 SE in the south. Below the UC are 6 km[sup 2] of metasandstone and metafelsites of the BCS. The metasandstone is quartz-sericite schist with strong lineation ([minus]50 S70E) in its northern km of exposure. Bedding and foliation are NS 60 E in N, and NE 70 SE in S. This schist body is intruded on the E by a dike of quartz-phyric metafelsite to 1 km wide which underlies the UC along its entire length. The felsite shows strong relict flow layering and no foliation. Flow layering is NS 90 in the N, and strikes and dips variably in the S. A 1/4 km[sup 2] metafelsite plug intrudes the schist on the W, with flow layering NE 90. The two exposures of the UC are separated by a Precambrian normal fault striking N45E and dipping moderately SE under HCC alluvial fill; it has about a km of dip slip.

Erickson, R.C. (Sonoma State Univ., Rohnert Park, CA (United States). Geology Dept.)

1993-04-01T23:59:59.000Z

363

Chemical Engineering & Processing Humidity Information at ...  

Science Conference Proceedings (OSTI)

NIST Home > Chemical Engineering & Processing Humidity Information at NIST. Chemical Engineering & Processing Humidity Information at NIST. ...

2010-09-24T23:59:59.000Z

364

NEHRP - Earthquake Engineering Research Needs Reports  

Science Conference Proceedings (OSTI)

Library. Research Needs Reports Earthquake Engineering. Earthquake Engineering. 2004. Preventing Earthquake Disasters ...

365

Fundamental Interaction Mechanisms of Engineered ...  

Science Conference Proceedings (OSTI)

Fundamental Interaction Mechanisms of Engineered Nanomaterials with DNA. Summary: We utilized isotope-dilution liquid ...

2012-10-01T23:59:59.000Z

366

The Honolulu Engineer District Introduction  

E-Print Network (OSTI)

with jurisdiction over the Honolulu, Far East, and Okinawa districts.' Several histories of the engineer wartime

US Army Corps of Engineers

367

Engineering Research Division publication report  

SciTech Connect

This bibliography with abstracts lists citations of 118 formal reports in electronics engineering. (LEW)

Miller, E.K.; Livingston, P.L.

1983-07-01T23:59:59.000Z

368

Genetically Engineered Ethanol Producing Microorganisms ...  

Search PNNL. PNNL Home; About; Research; Publications; Jobs; News; Contacts; Genetically Engineered Ethanol Producing Microorganisms. Battelle ...

369

Clean Cities: Natural Gas Vehicle Technology Forum 2008 Meeting...  

NLE Websites -- All DOE Office Websites (Extended Search)

Baytech CNG Heavy-Duty Vehicles and Engines Richard Turner, Baytech Corporation Biogas for Transportation Jon Lear, Ruby Mountain, Inc. Biogas to LNG John A. Barclay,...

370

Information Systems Engineering Guidance (ISEG)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Departmental Information Systems Engineering (DISE) Departmental Information Systems Engineering (DISE) Volume 1 Information Systems Engineering Lifecycle January 31, 2002 Software Quality and Systems Engineering Program Office of the Associate CIO of Architecture, Standards & Planning Office of the Chief Information Officer Title Page Document Series: Departmental Information Systems Engineering Document Name: Volume 1, Information Systems Engineering Lifecycle Publication Date: 01/31/02 Document Owner: Software Quality and Systems Engineering Program Office of the Associate CIO of Architecture, Standards & Planning The concepts and processes in this document are aligned with the DOE Information Management (IM) Strategic Plan Mission and Goals. The Information Management Mission is:

371

Chemical and Paper Engineering Student Handbook  

E-Print Network (OSTI)

Chemical and Paper Engineering Student Handbook 2010-2011 #12;i Table of Contents 2010-2011 Letter-2011.......................................................................... 32 Chemical Engineering Major Curriculum .......................................... 2010.............................. Double Major: Chemical Engineering and Paper Science and Engineering......... 60 Chemical Engineering

Dollar, Anna

372

SNF Project Engineering Process Improvement Plan  

SciTech Connect

This plan documents the SNF Project activities and plans to support its engineering process. It describes five SNF Project Engineering initiatives: new engineering procedures, qualification cards process; configuration management, engineering self assessments, and integrated schedule for engineering activities.

DESAI, S.P.

2000-02-09T23:59:59.000Z

373

Southwestern Regional Partnership For Carbon Sequestration (Phase 2) Pump Canyon CO2- ECBM/Sequestration Demonstration, San Juan Basin, New Mexico  

SciTech Connect

Within the Southwest Regional Partnership on Carbon Sequestration (SWP), three demonstrations of geologic CO{sub 2} sequestration are being performed -- one in an oilfield (the SACROC Unit in the Permian basin of west Texas), one in a deep, unmineable coalbed (the Pump Canyon site in the San Juan basin of northern New Mexico), and one in a deep, saline reservoir (underlying the Aneth oilfield in the Paradox basin of southeast Utah). The Pump Canyon CO{sub 2}-enhanced coalbed methane (CO{sub 2}/ECBM) sequestration demonstration project plans to demonstrate the effectiveness of CO{sub 2} sequestration in deep, unmineable coal seams via a small-scale geologic sequestration project. The site is located in San Juan County, northern New Mexico, just within the limits of the high-permeability fairway of prolific coalbed methane production. The study area for the SWP project consists of 31 coalbed methane production wells located in a nine section area. CO{sub 2} was injected continuously for a year and different monitoring, verification and accounting (MVA) techniques were implemented to track the CO{sub 2} movement inside and outside the reservoir. Some of the MVA methods include continuous measurement of injection volumes, pressures and temperatures within the injection well, coalbed methane production rates, pressures and gas compositions collected at the offset production wells, and tracers in the injected CO{sub 2}. In addition, time-lapse vertical seismic profiling (VSP), surface tiltmeter arrays, a series of shallow monitoring wells with a regular fluid sampling program, surface measurements of soil composition, CO{sub 2} fluxes, and tracers were used to help in tracking the injected CO{sub 2}. Finally, a detailed reservoir model was constructed to help reproduce and understand the behavior of the reservoir under production and injection operation. This report summarizes the different phases of the project, from permitting through site closure, and gives the results of the different MVA techniques.

Advanced Resources International

2010-01-31T23:59:59.000Z

374

Ceramic Automotive Stirling Engine Program  

SciTech Connect

The Ceramic Automotive Stirling Engine Program evaluated the application of advanced ceramic materials to an automotive Stirling engine. The objective of the program was to evaluate the technical feasibility of utilizing advanced ceramics to increase peak engine operating temperature, and to evaluate the performance benefits of such an increase. Manufacturing cost estimates were also developed for various ceramic engine components and compared with conventional metallic engine component costs.

Not Available

1986-08-01T23:59:59.000Z

375

E-Alerts: Combustion, engines, and propellants (reciprocation and rotating combustion engines). E-mail newsletter  

Science Conference Proceedings (OSTI)

Design, performance, and testing of reciprocating and rotating engines of various configurations for all types of propulsion. Includes internal and external combustion engines; engine exhaust systems; engine air systems components; engine structures; stirling and diesel engines.

NONE

1999-04-01T23:59:59.000Z

376

Single rotor turbine engine  

SciTech Connect

There has been invented a turbine engine with a single rotor which cools the engine, functions as a radial compressor, pushes air through the engine to the ignition point, and acts as an axial turbine for powering the compressor. The invention engine is designed to use a simple scheme of conventional passage shapes to provide both a radial and axial flow pattern through the single rotor, thereby allowing the radial intake air flow to cool the turbine blades and turbine exhaust gases in an axial flow to be used for energy transfer. In an alternative embodiment, an electric generator is incorporated in the engine to specifically adapt the invention for power generation. Magnets are embedded in the exhaust face of the single rotor proximate to a ring of stationary magnetic cores with windings to provide for the generation of electricity. In this alternative embodiment, the turbine is a radial inflow turbine rather than an axial turbine as used in the first embodiment. Radial inflow passages of conventional design are interleaved with radial compressor passages to allow the intake air to cool the turbine blades.

Platts, David A. (Los Alamos, NM)

2002-01-01T23:59:59.000Z

377

Free-piston engine  

DOE Patents (OSTI)

A combustion system which can utilize high compression ratios, short burn durations, and homogeneous fuel/air mixtures in conjunction with low equivalence ratios. In particular, a free-piston, two-stroke autoignition internal combustion engine including an electrical generator having a linear alternator with a double-ended free piston that oscillates inside a closed cylinder is provided. Fuel and air are introduced in a two-stroke cycle fashion on each end, where the cylinder charge is compressed to the point of autoignition without spark plugs. The piston is driven in an oscillating motion as combustion occurs successively on each end. This leads to rapid combustion at almost constant volume for any fuel/air equivalence ratio mixture at very high compression ratios. The engine is characterized by high thermal efficiency and low NO.sub.x emissions. The engine is particularly suited for generating electrical current in a hybrid automobile.

Van Blarigan, Peter (Truckee, CA)

2001-01-01T23:59:59.000Z

378

BEW Engineering | Open Energy Information  

Open Energy Info (EERE)

BEW Engineering BEW Engineering Jump to: navigation, search Name BEW Engineering Place San Ramon, California Zip 94583 Sector Services Product BEW Engineering provides engineering consulting services, and performs research and development in electrical power systems for bulk power and distributed energy resource applications. References BEW Engineering[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. BEW Engineering is a company located in San Ramon, California . References ↑ "BEW Engineering" Retrieved from "http://en.openei.org/w/index.php?title=BEW_Engineering&oldid=342696" Categories: Clean Energy Organizations Companies Organizations Stubs What links here

379

Information Systems Engineering Guidance (ISEG)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Departmental Information Systems Engineering (DISE) Departmental Information Systems Engineering (DISE) Guidance Volume 2 Managing DOE IT Projects March 26, 2002 Revised December 27, 2002 Developed by the Software Quality and Systems Engineering Program Office of the Chief Information Officer Departmental Information Systems Engineering Guidance Title Page Document Series: Departmental Information Systems Engineering (DISE) Guidance Document Name: Volume 2, Managing DOE IT Projects Publication Date: 03/26/03, Revised 12/27/02 Document Owner: Office of the Chief Information Officer Software Quality and Systems Engineering Brenda Coblentz, IM-21, Program Manager Acknowledgement: Wayne Jones, author of the DOE (HQ) IM Project Management Guide, September 1998

380

DEPARTMENT OF MECHANICAL ENGINEERING  

E-Print Network (OSTI)

the Chair Advanced Power Systems Research Group Engineering Education Innovation Research Group Mechanics of MultiScale Materials Research Group MultiScale Systems and Sensors Research Group Space Systems Research Group Sustainable Manufacturing and Design Research Group Faculty Profiles Michigan

Endres. William J.

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Logic Engines as Interactors  

Science Conference Proceedings (OSTI)

We introduce a new programming language construct, Interactors , supporting the agent-oriented view that programming is a dialog between simple, self-contained, autonomous building blocks. We define Interactors ... Keywords: agent oriented programming language constructs, generalized iterators, logic engines, metaprogramming

Paul Tarau

2008-12-01T23:59:59.000Z

382

Mining Engineering Strategic Plan  

E-Print Network (OSTI)

, coal, base and ferrous metals. Action 1.3.2: The Tianfu Mining University Opportunity: Strengthen.1.2: Endowed Chair in Energy: Endow a $3 million Chair in Mining Engineering with emphasis on Energy form Coal Control, Mineral-Materials-Coal Processing, Mine Health and Safety, and Mine Survey laboratories. Action 4

Ragsdell, Kenneth M.

383

Mechanical engineering Department Seminar  

E-Print Network (OSTI)

power generation gas turbines and jet engines. As the energy efficiency of gas turbines in- creases to pro- vide thermal protection to turbine blades and vanes in the hottest sections of both electric with turbine inlet turbine, advances in turbine efficiency depend on improved ther- mal barrier coatings

384

Hydrogen Fuel Cell Engines  

E-Print Network (OSTI)

the batteries, and to power accessories like the air condi- tioner and heater. Hybrid electric cars can exceed#12;#12;Hydrogen Fuel Cell Engines MODULE 8: FUEL CELL HYBRID ELECTRIC VEHICLES CONTENTS 8.1 HYBRID ELECTRIC VEHICLES .................................................................................. 8-1 8

385

Handbook of energy engineering  

Science Conference Proceedings (OSTI)

This book covers the following topics: Fundamentals of energy engineering; Energy economic analysis; Energy auditing and accounting; Electrical system optimization; Waste heat recovery; Utility system optimization; Heating, ventilation, air conditioning, and building system optimization; HVAC equipment; Cogeneration: theory and practice; Control systems; Computer applications; Thermal storage; Passive solar energy systems; and Energy management.

Mehta, D.P.; Thumann, A.

1989-01-01T23:59:59.000Z

386

Engineeringtechnology COLLEGE of ENGINEERING  

E-Print Network (OSTI)

to support the rapidly evolving advanced powertrain sector, including alternative fuel, clean diesel campus. Associate Professor Caisheng Wang's wind turbine tops the roof of the Engineering Technology Building, harnessing the wind to create a renewable energy system strong enough to power a computer lab

Chinnam, Ratna Babu

387

ENGINEERING HOWARD R. HUGHES  

E-Print Network (OSTI)

a solar-powered house that is energy-efficient, affordable, and attractive. ·Every graduating major of Energy Solar Decathlon 2013. Engineering and architecture students will design then build and operate to the future of Las Vegas. Their work is funded by agencies including the National Science Foundation

Hemmers, Oliver

388

Engineering Annual Summary 1996  

SciTech Connect

Fiscal year 1996 has been a year of significant change for the Lawrence Livermore National Laboratory (LLNL) in general and for Engineering in particular. Among these changes, the Laboratory`s national security mission was better defined, the stockpile stewardship program objectives became crisper, LLNL`s investment in high-performance computing was re-emphasized with the procurement of a $100 million supercomputer for the Laboratory`s Accelerated Strategic Computing Initiative (ASCI) program, two major Laser programs (the National Ignition Facility and Atomic Vapor Laser Isotope Separation) expanded significantly, and DOE`s human genome efforts moved to the next phase of development. In the area of business operations, LLNL`s Cost Cutting Initiative Program (CCIP) was completed and the Laboratory restructured its workforce using a Voluntary Separation Incentive Program (VSIP). Engineering similarly also saw many technical and programmatic successes, as well as changes, starting with completion of its strategic plan, significant consolidation of its facilities, restructuring of its workforce, reduction of its overhead costs, substantial transfers of staff between programs, and finally my personal arrival at Livermore. This report is the first opportunity to capture some of Engineering`s FY96 activities and accomplishments in a succinct fashion, and to relate these to our strategic plan.

Dimolitsas, S.

1997-04-30T23:59:59.000Z

389

DOE Systems Engineering Methodology  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Systems Engineering Methodology (SEM) In-Stage Assessment Process Guide Version 3 September 2002 U.S. Department of Energy Office of the Chief Information Officer In-Stage Assessment Process Date: September 2002 Page i Rev Date: Table of Contents Section Page 1.0 Overview .......................................................................................................................................... 1 Introduction........................................................................................................................ 1 Purpose .............................................................................................................................. 1 Who Conducts ...................................................................................................................

390

Automotive Stirling Engine Development Program Mod I Stirling engine development  

SciTech Connect

The Automotive Stirling Engine (ASE) Development Program was established to enable research and development of alternate propulsion systems. The program was awarded to Mechanical Technology Incorporated (MTI) for the purpose of developing an automotive Stirling engine, and transferring Stirling-engine technology to the United States. MTI has fabricated and tested four Mod I engines that have accumulated over 1900 test hours to date. The engines evaluated in the test cell have achieved an average of 34.5% efficiency at their maximum efficiency point (2000 rpm), and have developed an average maximum output power (power available to the drive train) level of 54.4 kW (73.2 bhp). All engines are still operating, and are being used to develop components and control strategy for the Upgraded Mod I engine design (predicted to increase maximum power output and efficiency while reducing total engine system weight).

Simetkosky, M.A.

1983-08-01T23:59:59.000Z

391

Value engineering: A new focus for women in engineering  

SciTech Connect

Value Engineering is an organized problem solving technique that utilizes communication and teamwork skills -- skills heralded as strengths for women. Value Engineering offers an excellent career opportunity for women in the engineering profession. It is an expanded career path that is currently being overlooked by women. Value Engineering is supported by SAVE (Society of American Value Engineers) and certification in the process can be achieved in two years. For women in the engineering profession, VE is an ideal place to redirect their existing skills and training. The number of certified women is a minority, creating a wide-open field of opportunity in federal and state agencies as well as private industry. Value Engineering can provide that new avenue for engineering careers -- a new direction where current skills can be applied to a diverse and exciting profession. 1 fig.

Anderson, L.C.

1990-04-20T23:59:59.000Z

392

Cloud engineering is Search Based Software Engineering too  

Science Conference Proceedings (OSTI)

Many of the problems posed by the migration of computation to cloud platforms can be formulated and solved using techniques associated with Search Based Software Engineering (SBSE). Much of cloud software engineering involves problems of optimisation: ... Keywords: Cloud computing, Search Based Software Engineering (SBSE)

Mark Harman, Kiran Lakhotia, Jeremy Singer, David R. White, Shin Yoo

2013-09-01T23:59:59.000Z

393

Engineer, Sandia National Laboratories | National Nuclear Security...  

NLE Websites -- All DOE Office Websites (Extended Search)

Clifford Ho, a Sandia engineer, has been selected by the Chinese Institute of Engineers - USA to receive the Asian American Engineer of the Year Award. The honor is...

394

BGA Engineering LLC | Open Energy Information  

Open Energy Info (EERE)

Solar Product Engineering firm specialising in substation engineering and design, power plant engineering and on-site generation, including cogeneration, solar and...

395

Engineer, Sandia National Laboratories | National Nuclear Security...  

National Nuclear Security Administration (NNSA)

Clifford Ho Engineer, Sandia National Laboratories Clifford Ho Clifford Ho Role: Engineer, Sandia National Laboratories Award: Asian American Engineer of the Year Profile: Clifford...

396

Fagen Engineering LLC | Open Energy Information  

Open Energy Info (EERE)

Engineering LLC Place Granite Falls, Minnesota Zip 56241 Product Designs and builds ethanol production plants and other engineering projects. References Fagen Engineering LLC1...

397

STM Stirling Engine-Generators  

Science Conference Proceedings (OSTI)

Stirling engines have recently been introduced to the distributed generation market. This project summarizes the experience of three projects implementing Stirling engine-generators from one manufacturer in applications where they are fueled with digester gas.

2007-03-23T23:59:59.000Z

398

UCL Science Library Map Engineering  

E-Print Network (OSTI)

UCL Science Library Map Floor 4 Engineering Engineering Periodicals Guter Collection Sta Training Room Floor 3 Chemistry Computer Science Geology Geosciences Periodicals History of Science Maths Maths Periodicals Physical Sciences Periodicals Physics Computer Cluster Group Study Area Information Library

Crawford, Ian

399

Integrated Computational Materials Engineering (ICME)  

Science Conference Proceedings (OSTI)

Presentation Title, Integrated Computational Materials Engineering (ICME) in the Automotive Industry: Successes and Opportunities. Author(s), Louis Gerard...

400

International Governance of Climate Engineering  

E-Print Network (OSTI)

Solar Radiation Management Governance Initiative conference); Daniel Bodansky, Governing Climate Engineering: Scenarios for Analysis (Harvard Project on Climate Agreements,

Parson, Edward; Ernst, Lia

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Argonne Chemical Sciences & Engineering - People  

NLE Websites -- All DOE Office Websites (Extended Search)

Ceramic Electrochemistry Electrochemical Projects Support Anthony Burrell Electrochemical Energy Storage Management and Support Basic Research Applied R&D Engineering...

402

Organization - Nuclear Engineering Division (Argonne)  

NLE Websites -- All DOE Office Websites (Extended Search)

Nuclear Safety Materials Disposition Decontamination & Decommissioning Nuclear Criticality Safety Nuclear Data Program Nuclear Waste Form Modeling Departments Engineering...

403

Achievements: Nuclear Engineering Division (Argonne)  

NLE Websites -- All DOE Office Websites (Extended Search)

Nuclear Safety Materials Disposition Decontamination & Decommissioning Nuclear Criticality Safety Nuclear Data Program Nuclear Waste Form Modeling Departments Engineering...

404

Engine idle speed control system  

SciTech Connect

An idle speed control system is described for an internal combustion engine having a fuel delivery means for supplying fuel to the engine, the idle speed control system comprising in combination: means for controlling the fuel delivery means to supply a scheduled idle fuel quantity during a idle operating state of the engine; means for sensing the engine idle speed; integrator means responsive to the engine idle speed and a desired engine idle speed for adjusting the scheduled idle fuel quantity in direction and amount to cause correspondence between the engine idle speed and the desired engine idle speed, the integrator means adjustment being a measure of engine load conditions; and means for establishing the scheduled idle fuel quantity, the means including (A) means for establishing a family of curves as a function of the amount of integrator adjustment of the scheduled idle fuel quantity, each curve of the family of curves representing idle fuel quantity as a function of engine idle speed for a respective engine load condition, and (B) means for selecting the curve corresponding to the integrator adjustment of the scheduled idle fuel quantity and providing the scheduled fuel quantity from the selected curve in accord with the sensed engine idle speed.

Ament, F.

1986-07-01T23:59:59.000Z

405

wind engineering & natural disaster mitigation  

E-Print Network (OSTI)

wind engineering & natural disaster mitigation #12;wind engineering & natural disaster mitigation Investment WindEEE Dome at Advanced Manufacturing Park $31million Insurance Research Lab for Better Homes $8million Advanced Facility for Avian Research $9million #12;wind engineering & natural disaster mitigation

Sinnamon, Gordon J.

406

Industrial Engineering Department Graduate Handbook  

E-Print Network (OSTI)

Handbook Page 4 Engineering Graduate Program if: (1) his/her undergraduate degree lacks fundamental by the student and the I.E. Graduate Advisor. #12;IE Department Graduate Handbook Page 5 4.2 Fundamental SystemsIndustrial Engineering Department Graduate Handbook Master of Science in Industrial Engineering

Rock, Chris

407

Engineering of markets and artifacts  

Science Conference Proceedings (OSTI)

In this paper, we continue the dialog started by Roth [19] between economics and engineering in the context of design of markets. We take the position that markets and engineered artifacts are thee the products of a social process of design formulation. ... Keywords: engineering design, market design, methodologies, modeling, testing

Eswaran Subrahmanian; Sarosh N. Talukdar

2003-09-01T23:59:59.000Z

408

Ecological Engineering Undergraduate Advising Guide  

E-Print Network (OSTI)

, biochemistry and engineering analysis and design, students in this program will receive training in biology with ecological, agricultural and natural resource systems management. Students receive training in engineering engineering design and analysis techniques to address a wide range of ecological, agricultural and natural

Tullos, Desiree

409

ARM - Engineering Change Request & Engineering Change Order Guidelines  

NLE Websites -- All DOE Office Websites (Extended Search)

Change Request & Change Request & Engineering Change Order Guidelines Page Contents: Guideline for Starting a Request for a New ARM Product, Capability, or Functionality Engineering Task Tracking Tool Tracking Capabilities Getting Closure, the Baseline Change Request Glossary Engineering Change Request & Engineering Change Order Guidelines Requesting Engineered Products and Services in ARM Guideline for Starting a Request for a New ARM Product, Capability, or Functionality The purpose of this guideline is to establish a method that members of the ARM Infrastructure team may use to submit requests for products and services from the ARM Engineering Group. The concept of "new product, capability, or functionality" refers to the idea that requests the ARM Infrastructure Team to make to the Engineering Group that will ultimately

410

Engines Photo Archive  

NLE Websites -- All DOE Office Websites (Extended Search)

Engines Photo Archive Engines Photo Archive The following images may be used freely as long as they are accompanied by a statement that they were used "Courtesy of Argonne National Laboratory" (see our disclaimer). To download the high-resolution version of each picture, right-click on the "Download high-resolution image" text beneath the picture and select "Save Link As..." from the resulting pop-up menu. A researcher readies an endoscope to capture diesel emissions images. Diesel Emissions: Readying an endoscope to capture diesel emissions images.Photo courtesy of Argonne National Laboratory. Download high-resolution image. A researcher readies an endoscope to capture diesel emissions images. Diesel Particulates: Argonne's micro-imaging system for diesel particulates. Read story. Download high-resolution image.

411

HANFORD ENGINEER WORKS  

Office of Legacy Management (LM)

HANFORD ENGINEER WORKS HANFORD ENGINEER WORKS IJd *P-t - - ~~~ssiticatiC+n cwcetted rat G.E. NUCLEONICS PROJECT xi I ~@L.%&~--G-ENERAI,@ ELECTRIC z ,m ._.__.-. _ I--..-. By Authority of. COMPANY ._ Atmic Energy Commission Office of Hanford Dire&xl Operations Riohland, Washington Attention; Mr. Carleton Shugg, Manager ./ ALPKA-ROLLED EL'GIL%I jw -879 ' . *_ a. f' Richland, Washington February 6, 1948 , Thla Dclc.Jv-

412

Internal combustion engine  

DOE Patents (OSTI)

An improved engine is provided that more efficiently consumes difficult fuels such as coal slurries or powdered coal. The engine includes a precombustion chamber having a portion thereof formed by an ignition plug. The precombustion chamber is arranged so that when the piston is proximate the head, the precombustion chamber is sealed from the main cylinder or the main combustion chamber and when the piston is remote from the head, the precombustion chamber and main combustion chamber are in communication. The time for burning of fuel in the precombustion chamber can be regulated by the distance required to move the piston from the top dead center position to the position wherein the precombustion chamber and main combustion chamber are in communication.

Baker, Quentin A. (P.O. Box 6477, San Antonio, TX 78209); Mecredy, Henry E. (1630-C W. 6th, Austin, TX 78703); O' Neal, Glenn B. (6503 Wagner Way, San Antonio, TX 78256)

1991-01-01T23:59:59.000Z

413

Modular Aneutronic Fusion Engine  

SciTech Connect

NASA's JUNO mission will arrive at Jupiter in July 2016, after nearly five years in space. Since operational costs tend to rise with mission time, minimizing such times becomes a top priority. We present the conceptual design for a 10MW aneutronic fusion engine with high exhaust velocities that would reduce transit time for a Jupiter mission to eighteen months and enable more challenging exploration missions in the solar system and beyond. __________________________________________________

Gary Pajer, Yosef Razin, Michael Paluszek, A.H. Glasser and Samuel Cohen

2012-05-11T23:59:59.000Z

414

An Engineering Test Reactor  

SciTech Connect

A relatively inexpensive reactor for the specific purpose of testing a sub-critical portion of another reactor under conditions that would exist during actual operation is discussed. It is concluded that an engineering tool for reactor development work that bridges the present gap between exponential and criticality experiments and the actual full scale operating reactor is feasible. An example of such a test reactor which would not entail development effort to ut into operation is depicted.

Fahrner, T.; Stoker, R.L.; Thomson, A.S.

1951-03-16T23:59:59.000Z

415

MARS Flight Engineering Status  

DOE Green Energy (OSTI)

The Multi-sensor Airborne Radiation Survey Flight Engineering project (MARS FE) has designed a high purity germanium (HPGe) crystal array for conducting a wide range of field measurements. In addition to the HPGe detector system, a platform-specific shock and vibration isolation system and environmental housing have been designed to support demonstration activities in a maritime environment on an Unmanned Surface Vehicle (USV). This report describes the status of the equipment as of the end of FY09.

Fast, James E.; Dorow, Kevin E.; Morris, Scott J.; Thompson, Robert C.; Willett, Jesse A.

2010-04-06T23:59:59.000Z

416

Photonically Engineered Incandescent Emitter  

DOE Patents (OSTI)

A photonically engineered incandescence is disclosed. The emitter materials and photonic crystal structure can be chosen to modify or suppress thermal radiation above a cutoff wavelength, causing the emitter to selectively emit in the visible and near-infrared portions of the spectrum. An efficient incandescent lamp is enabled thereby. A method for fabricating a three-dimensional photonic crystal of a structural material, suitable for the incandescent emitter, is also disclosed.

Gee, James M. (Albuquerque, NM); Lin, Shawn-Yu (Albuquerque, NM); Fleming, James G. (Albuquerque, NM); Moreno, James B. (Albuquerque, NM)

2005-03-22T23:59:59.000Z

417

Stirling cycle engine  

DOE Patents (OSTI)

In a Stirling cycle engine having a plurality of working gas charges separated by pistons reciprocating in cylinders, the total gas content is minimized and the mean pressure equalization among the serial cylinders is improved by using two piston rings axially spaced at least as much as the piston stroke and by providing a duct in the cylinder wall opening in the space between the two piston rings and leading to a source of minimum or maximum working gas pressure.

Lundholm, Gunnar (Lund, SE)

1983-01-01T23:59:59.000Z

418

Materials Science and Engineering  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Materials Science and Engineering Materials Science and Engineering 1 Fe---Cr A lloys f or A dvanced N uclear E nergy A pplica9ons Ron S caEngineering 2 Thermodynamic S tabiliza9on o f G rain S ize The concept is that non---equilibrium solutes introduced by mechanical alloying can segregate to grain b oundaries, p roducing

419

Index Terms --Smart grid; power engineering education; power engineering curriculum; power engineering re-  

E-Print Network (OSTI)

1 Index Terms -- Smart grid; power engineering education; power engineering curriculum; power the United States power system has led to an engineering initiative va- riously known as `smart grid the smart grid will be educated, how they should be trained, and to what levels of comprehension

420

CHEMICAL ENGINEERING Fall 2013-Winter 2014  

E-Print Network (OSTI)

ADVANCED CHEMICAL ENGINEERING Fall 2013-Winter 2014 Certificate Program CONTINUING AND PROFESSIONAL EDUCATIONCONTINUING AND PROFESSIONAL EDUCATION #12;About the Advanced Chemical Engineering Certificate Program The new Advanced Chemical Engineering Certificate Program offers professionals in chemi- cal engineering

California at Davis, University of

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

University of Ljubljana Faculty of Electrical Engineering  

E-Print Network (OSTI)

calculation for different criteria. Ancillary service management: load forecast, power system reserve forecast#12;2 3 University of Ljubljana Faculty of Electrical Engineering University of Ljubljana Faculty of Electrical Engineering Doctoral Programme Electrical Engineering Doctoral Programme Electrical Engineering

?umer, Slobodan

422

Vehicle Technologies Office: Combustion Engine Research  

NLE Websites -- All DOE Office Websites (Extended Search)

Combustion Engine Combustion Engine Research to someone by E-mail Share Vehicle Technologies Office: Combustion Engine Research on Facebook Tweet about Vehicle Technologies Office: Combustion Engine Research on Twitter Bookmark Vehicle Technologies Office: Combustion Engine Research on Google Bookmark Vehicle Technologies Office: Combustion Engine Research on Delicious Rank Vehicle Technologies Office: Combustion Engine Research on Digg Find More places to share Vehicle Technologies Office: Combustion Engine Research on AddThis.com... Just the Basics Hybrid & Vehicle Systems Energy Storage Advanced Power Electronics & Electrical Machines Advanced Combustion Engines Combustion Engines Emission Control Waste Heat Recovery Fuels & Lubricants Materials Technologies Combustion Engine Research

423

Bandgap Engineering | Open Energy Information  

Open Energy Info (EERE)

Engineering Engineering Jump to: navigation, search Name Bandgap Engineering Place Woburn, Massachusetts Zip 1801 Sector Efficiency Product US-based company developing highly tunable and inexpensive methods for nano-structuring silicon and is applying these technologies to high efficiency photovoltaic systems and high capacity Li-ion batteries. References Bandgap Engineering[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Bandgap Engineering is a company located in Woburn, Massachusetts . References ↑ "Bandgap Engineering" Retrieved from "http://en.openei.org/w/index.php?title=Bandgap_Engineering&oldid=342515" Categories: Clean Energy Organizations

424

Honda motor company's CVCC engine  

DOE Green Energy (OSTI)

Honda Motor Company of Japan in a four-year period from 1968 to 1872 designed, tested, and mass-produced a stratified charge engine, the CVCC, which in comparison to conventional engines of similar output at the time was lower in CO, HC and NO/sub x/ emissions and higher in fuel economy. Honda developed the CVCC engine without government assistance or outside help. Honda's success came at a time when steadily increasing fuel costs and the various provisions of the Clean Air Act had forced US automakers to consider possible alternatives to the conventional gasoline engine. While most major engine manufacturers had investigated some form of stratified charge engine, Honda's CVCC was the only one to find successful market application. This case study examines the circumstances surrounding the development of the CVCC engine and its introduction into the Japanese and American markets.

Abernathy, W.J.; Ronan, L.

1980-07-01T23:59:59.000Z

425

Mechanical Engineering Department technical abstracts  

SciTech Connect

The Mechanical Engineering Department publishes abstracts twice a year to inform readers of the broad range of technical activities in the Department, and to promote an exchange of ideas. Details of the work covered by an abstract may be obtained by contacting the author(s). General information about the current role and activities of each of the Department's seven divisions precedes the technical abstracts. Further information about a division's work may be obtained from the division leader, whose name is given at the end of each divisional summary. The Department's seven divisions are as follows: Nuclear Test Engineering Division, Nuclear Explosives Engineering Division, Weapons Engineering Division, Energy Systems Engineering Division, Engineering Sciences Division, Magnetic Fusion Engineering Division and Materials Fabrication Division.

1984-07-01T23:59:59.000Z

426

Engineered Fire Safety Group Staff Directory  

Science Conference Proceedings (OSTI)

Engineered Fire Safety Group Staff. Staff Listing. Thomas G. Cleary, (Acting) Leader, Chemical Engineer, 301-975-6858. Carla ...

2013-09-16T23:59:59.000Z

427

SOFTWARE QUALITY & SYSTEMS ENGINEERING PROGRAM: Project Tracking...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

SOFTWARE QUALITY & SYSTEMS ENGINEERING PROGRAM: Project Tracking Checklist SOFTWARE QUALITY & SYSTEMS ENGINEERING PROGRAM: Project Tracking Checklist The following checklist is...

428

SOFTWARE QUALITY & SYSTEMS ENGINEERING PROGRAM: Project Tracking...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

& SYSTEMS ENGINEERING PROGRAM: Project Planning Checklist SOFTWARE QUALITY & SYSTEMS ENGINEERING PROGRAM: Software Design Checklist Energy.gov Careers & Internships Policy &...

429

SOFTWARE QUALITY & SYSTEMS ENGINEERING PROGRAM: Project Planning...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

SYSTEMS ENGINEERING PROGRAM: Requirements Management Checklist SOFTWARE QUALITY & SYSTEMS ENGINEERING PROGRAM: Project Tracking Checklist Energy.gov Careers & Internships Policy &...

430

SOFTWARE QUALITY & SYSTEMS ENGINEERING PROGRAM: Software Design...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

SYSTEMS ENGINEERING PROGRAM: Requirements Management Checklist SOFTWARE QUALITY & SYSTEMS ENGINEERING PROGRAM: Project Tracking Checklist Energy.gov Careers & Internships Policy &...

431

SOFTWARE QUALITY & SYSTEMS ENGINEERING PROGRAM : Acceptance Checklist...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

& SYSTEMS ENGINEERING PROGRAM: Software Design Checklist SOFTWARE QUALITY & SYSTEMS ENGINEERING PROGRAM: Project Tracking Checklist Energy.gov Careers & Internships Policy &...

432

SOFTWARE QUALITY & SYSTEMS ENGINEERING PROGRAM | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Training Checklist SOFTWARE QUALITY & SYSTEMS ENGINEERING PROGRAM More Documents & Publications SOFTWARE QUALITY & SYSTEMS ENGINEERING PROGRAM SOFTWARE QUALITY & SYSTEMS...

433

US Army Corps of Engineers BUILDING STRONG  

E-Print Network (OSTI)

® Office Structure Par 005 / Office of Engineer Inspector General 01 *Supv Engineer Inspector General GS-15 02 Engineer Inspector General Rep GS-13 03 Administrative Officer GS-09 *The Engineer InspectorUS Army Corps of Engineers BUILDING STRONG® Mission Briefing The Engineer Inspector General #12

US Army Corps of Engineers

434

ION ROCKET ENGINE  

DOE Patents (OSTI)

A thrust generating engine utilizing cesium vapor as the propellant fuel is designed. The cesium is vaporized by heat and is passed through a heated porous tungsten electrode whereby each cesium atom is fonized. Upon emergfng from the tungsten electrode, the ions are accelerated rearwardly from the rocket through an electric field between the tungsten electrode and an adjacent accelerating electrode grid structure. To avoid creating a large negative charge on the space craft as a result of the expulsion of the positive ions, a source of electrons is disposed adjacent the ion stream to neutralize the cesium atoms following acceleration thereof. (AEC)

Ehlers, K.W.; Voelker, F. III

1961-12-19T23:59:59.000Z

435

Acoustical heat pumping engine  

DOE Patents (OSTI)

The disclosure is directed to an acoustical heat pumping engine without moving seals. A tubular housing holds a compressible fluid capable of supporting an acoustical standing wave. An acoustical driver is disposed at one end of the housing and the other end is capped. A second thermodynamic medium is disposed in the housing near to but spaced from the capped end. Heat is pumped along the second thermodynamic medium toward the capped end as a consequence both of the pressure oscillation due to the driver and imperfect thermal contact between the fluid and the second thermodynamic medium.

Wheatley, John C. (Los Alamos, NM); Swift, Gregory W. (Los Alamos, NM); Migliori, Albert (Santa Fe, NM)

1983-08-16T23:59:59.000Z

436

Materials science and engineering  

Science Conference Proceedings (OSTI)

During FY-96, work within the Materials Science and Engineering Thrust Area was focused on material modeling. Our motivation for this work is to develop the capability to study the structural response of materials as well as material processing. These capabilities have been applied to a broad range of problems, in support of many programs at Lawrence Livermore National Laboratory. These studies are described in (1) Strength and Fracture Toughness of Material Interfaces; (2) Damage Evolution in Fiber Composite Materials; (3) Flashlamp Envelope Optical Properties and Failure Analysis; (4) Synthesis and Processing of Nanocrystalline Hydroxyapatite; and (5) Room Temperature Creep Compliance of Bulk Kel-E.

Lesuer, D.R.

1997-02-01T23:59:59.000Z

437

Acoustical heat pumping engine  

DOE Patents (OSTI)

The disclosure is directed to an acoustical heat pumping engine without moving seals. A tubular housing holds a compressible fluid capable of supporting an acoustical standing wave. An acoustical driver is disposed at one end of the housing and the other end is capped. A second thermodynamic medium is disposed in the housing near to but spaced from the capped end. Heat is pumped along the second thermodynamic medium toward the capped end as a consequence both of the pressure oscillation due to the driver and imperfect thermal contact between the fluid and the second thermodynamic medium. 2 figs.

Wheatley, J.C.; Swift, G.W.; Migliori, A.

1983-08-16T23:59:59.000Z

438

Vehicle Technologies Office: Advanced Combustion Engines  

NLE Websites -- All DOE Office Websites (Extended Search)

Advanced Combustion Advanced Combustion Engines to someone by E-mail Share Vehicle Technologies Office: Advanced Combustion Engines on Facebook Tweet about Vehicle Technologies Office: Advanced Combustion Engines on Twitter Bookmark Vehicle Technologies Office: Advanced Combustion Engines on Google Bookmark Vehicle Technologies Office: Advanced Combustion Engines on Delicious Rank Vehicle Technologies Office: Advanced Combustion Engines on Digg Find More places to share Vehicle Technologies Office: Advanced Combustion Engines on AddThis.com... Just the Basics Hybrid & Vehicle Systems Energy Storage Advanced Power Electronics & Electrical Machines Advanced Combustion Engines Combustion Engines Emission Control Waste Heat Recovery Fuels & Lubricants Materials Technologies Advanced Combustion Engines

439

Just the Basics: Diesel Engine  

NLE Websites -- All DOE Office Websites (Extended Search)

Today's direct-injection diesel Today's direct-injection diesel engines are more rugged, powerful, durable, and reliable than gasoline engines, and use fuel much more efficiently, as well. Diesel Engines Yesterday, Today, and Tomorrow Diesels are workhorse engines. That's why you find them powering heavy- duty trucks, buses, tractors, and trains, not to mention large ships, bulldozers, cranes, and other construction equipment. In the past, diesels fit the stereotype of muscle-bound behe- moths. They were dirty and sluggish, smelly and loud. That image doesn't apply to today's diesel engines, however, and tomorrow's diesels will show even greater improvements. They will be even more fuel efficient, more flexible in the fuels they can use, and also much cleaner in emissions. How Diesel Engines Work

440

Engineering | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Engineering | National Nuclear Security Administration Engineering | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Continuing Management Reform Countering Nuclear Terrorism About Us Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Media Room Congressional Testimony Fact Sheets Newsletters Press Releases Speeches Events Social Media Video Gallery Photo Gallery NNSA Archive Federal Employment Apply for Our Jobs Our Jobs Working at NNSA Blog Engineering Home > About Us > Our Programs > Defense Programs > Future Science & Technology Programs > Engineering Engineering NNSA uses modern tools and capabilities in the engineering sciences field which are needed to ensure the safety, security, reliability and

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

The smallest possible heat engines  

E-Print Network (OSTI)

We construct the smallest possible self contained heat engines; one composed of only two qubits, the other of only a single qutrit. The engines are self-contained as they do not require external sources of work and/or control. They are able to produce work which is used to continuously lift a weight. Despite the dimension of the engine being small, it is still able to operate at the Carnot efficiency.

Noah Linden; Sandu Popescu; Paul Skrzypczyk

2010-10-28T23:59:59.000Z

442

Mechanical Engineering Department Technical Review  

Science Conference Proceedings (OSTI)

The Mechanical Engineering Department Technical Review is published to inform readers of various technical activities within the Department, promote exchange of ideas, and give credit to personnel who are achieving the results. The report is presented in two parts: technical achievements and publication abstracts. The first is divided into seven sections, each of which reports on an engineering division and its specific activities related to nuclear tests, nuclear explosives, weapons, energy systems, engineering sciences, magnetic fusion, and materials fabrication.

Carr, R.B.; Denney, R.M. (eds.)

1981-07-01T23:59:59.000Z

443

Steam Turbine Performance Engineer's Guide  

Science Conference Proceedings (OSTI)

The Steam Turbine Performance Engineer's Guide is meant to present the steam turbine performance engineer with the expected and important functions and responsibilities necessary to succeed in this position that are not necessarily taught in college. The instructions and recommendations in this guide, when properly executed, will improve the effectiveness of steam turbine performance engineers, positively affecting both the performance and reliability of the steam turbines under their care.

2010-12-23T23:59:59.000Z

444

High temperature turbine engine structure  

DOE Patents (OSTI)

A high temperature ceramic/metallic turbine engine includes a metallic housing which journals a rotor member of the turbine engine. A ceramic disk-like shroud portion of the engine is supported on the metallic housing portion and maintains a close running clearance with the rotor member. A ceramic spacer assembly maintains the close running clearance of the shroud portion and rotor member despite differential thermal movements between the shroud portion and metallic housing portion.

Carruthers, William D. (Mesa, AZ); Boyd, Gary L. (Tempe, AZ)

1992-01-01T23:59:59.000Z

445

High temperature turbine engine structure  

DOE Patents (OSTI)

A high temperature ceramic/metallic turbine engine includes a metallic housing which journals a rotor member of the turbine engine. A ceramic disk-like shroud portion of the engine is supported on the metallic housing portion and maintains a close running clearance with the rotor member. A ceramic spacer assembly maintains the close running clearance of the shroud portion and rotor member despite differential thermal movements between the shroud portion and metallic housing portion.

Carruthers, William D. (Mesa, AZ); Boyd, Gary L. (Tempe, AZ)

1993-01-01T23:59:59.000Z

446

High temperature turbine engine structure  

DOE Patents (OSTI)

A high temperature ceramic/metallic turbine engine includes a metallic housing which journals a rotor member of the turbine engine. A ceramic disk-like shroud portion of the engine is supported on the metallic housing portion and maintains a close running clearance with the rotor member. A ceramic spacer assembly maintains the close running clearance of the shroud portion and rotor member despite differential thermal movements between the shroud portion and metallic housing portion.

Carruthers, William D. (Mesa, AZ); Boyd, Gary L. (Tempe, AZ)

1994-01-01T23:59:59.000Z

447

Recycling of Engine Serviced Superalloys  

Science Conference Proceedings (OSTI)

of gas turbine engines and other high temperature applications. Elements such ... processes and tight controls have limited the use of large amounts of available.

448

Engine Combustion & Efficiency - FEERC  

NLE Websites -- All DOE Office Websites (Extended Search)

Engine Combustion & Efficiency Engine Combustion & Efficiency ORNL currently and historically supports the U.S. DOE on multi-cylinder and vehicle applications of diesel combustion, lean burn gasoline combustion, and low temperature combustion processes, and performs principal research on efficiency enabling technologies including emission controls, thermal energy recovery, and bio-renewable fuels. Research areas span from fundamental concepts to engine/vehicle integration and demonstration with a particular emphasis on the following areas: Thermodynamics for identifying and characterizing efficiency opportunities for engine-systems as well as the development of non-conventional combustion concepts for reducing fundamental combustion losses. Nonlinear sciences for improving the physical understanding and

449

Engineering performance of Bringelly shale.  

E-Print Network (OSTI)

??SYNOPSIS This thesis is concerned with the general and fundamental engineering characterisation of a geological formation within Wianamatta group, known as Bringelly shale. Bringelly shale (more)

William, Ezzat

2007-01-01T23:59:59.000Z

450

SEAMOPT - Stirling engine optimization code  

SciTech Connect

Experience is described with use of a fast-running Stirling engine optimization code developed at Argonne intended for public release. Stirling engine modeling is provided by the SEAM1 thermodynamic code. An interface was written to combine SEAM1 with a general optimization code and assess maximum component stress levels. Thus full engine thermodynamic and structural simulation is done during the optimization process. Several examples of the use of this code to optimize the GPU-3 engine are described. In one case efficiency was improved by over 25%.

Heames, T.J.; Daley, J.G.

1984-01-01T23:59:59.000Z

451

Biomass Engineering Prize Competition Announced  

Science Conference Proceedings (OSTI)

Posted on: 7/30/2010 12:00:00 AM... The DownEast 2010 Biomass Engineering Prize Competition is seeking innovative solutions focused on revitalizing an...

452

JOINT ELECTRICAL & COMPUTER ENGINEERING AND  

E-Print Network (OSTI)

JOINT ELECTRICAL & COMPUTER ENGINEERING AND PHYSICS COLLOQUIUM "Speckle Statistics, Coherence confirmation of the increase in the well- defined polarization state of the output radiation. In the joint

453

Engineering Biofuels from Photosynthetic Bacteria  

interdisciplinary target molecule selection and testing ... Engineering Biofuels from Photosynthetic Bacteria (IN 09001) November 2012 tdc_es_in09001_1112_mn

454

Quality engineering as a profession.  

SciTech Connect

Over the course of time, the profession of quality engineering has witnessed significant change, from its original emphasis on quality control and inspection to a more contemporary focus on upholding quality processes throughout the organization and its product realization activities. This paper describes the profession of quality engineering, exploring how today's quality engineers and quality professionals are certified individuals committed to upholding quality processes and principles while working with different dimensions of product development. It also discusses the future of the quality engineering profession and the future of the quality movement as a whole.

Kolb, Rachel R.; Hoover, Marcey L.

2012-12-01T23:59:59.000Z

455

Systems Engineering Advancement Research Initiative  

E-Print Network (OSTI)

strategic partners Define and research fundamental concepts for advanced system engineering Contribute materials, and handbooks to inspire, inform, and guide students and practitioners VENUE SEAri is located

de Weck, Olivier L.

456

Engineered Infills for Concrete Barriers  

Science Conference Proceedings (OSTI)

... INEEL Idaho National Engineering and Environmental Laboratory ... a 240 MW thermal sodiumcooled, graphite ... for cement based waste forms which ...

2011-05-20T23:59:59.000Z

457

Argonne Chemical Sciences & Engineering - Publications  

NLE Websites -- All DOE Office Websites (Extended Search)

and Fuel Cell Materials Ceramic Electrochemistry lithium-ion battery Electrochemical Energy Storage Basic Research Applied R&D Engineering Electrochemical Analysis and...

458

Development of Alternative Engine Materials  

Science Conference Proceedings (OSTI)

ature strength(31,32), and reinforced rings are envisioned in various IHPTET engine tests. The development of r-based materials with a balance of properties.

459

Engineered refractories for slagging gasifiers  

DOE Green Energy (OSTI)

Successful field trials in commercial slagging gasifier systems have been made of improved refractory materials engineered specifically for longer service life in this application.

Kwong, Kyei-sing; Bennett, James P.; Krabbe, Rick; Thomas, Hugh; Powell, Cynthia A.

2006-02-01T23:59:59.000Z

460

Computational methods in structural engineering.  

E-Print Network (OSTI)

???The present research is focused on computational methods in structural engineering. The main work includes three parts: 1) the development of cubic B-spline finite elements (more)

Yang, Hao (??)

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "ruby canyon engineering" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Materials Engineer Unravels Mutation Mystery  

Science Conference Proceedings (OSTI)

Aug 31, 2010 ... Just ask Kalina Hristova, an associate professor of materials science and engineering at Johns Hopkins University, who has spent more than...

462

Engineering and Technology Research & Development  

NLE Websites -- All DOE Office Websites (Extended Search)

Wang, Xiaoxing Wang July 09, 2012 Copyright 2012 RTI. All rights reserved Center for Energy Technology 2012 NETL CO 2 Capture Technology Meeting Engineering and Technology...

463

Alternative Energy Engineering Activity (Minnesota)  

Energy.gov (U.S. Department of Energy (DOE))

This statute establishes an alternative energy engineering activity to provide on-site technical assistance for alternative energy and conservation projects; develop information materials and...

464

Kevin E. Lansey Department of Civil Engineering and Engineering Mechanics  

E-Print Network (OSTI)

significant publications Lansey, K. and P. Boulos, Comprehensive Handbook on Water Quality Analysis Distribution Systems Analysis Handbook for Engineers and Planners, MW Soft, Inc., 2nd edition, 2006. Lansey, K for Water Distribution Pipe Network Models," ASCE Journal of Hydraulic Engineering, 127(4), April, 2001, pp

Scott, Christopher

465

US Army Corps of Engineers Engineer Research and Development Center  

E-Print Network (OSTI)

Energy Star or FEMP designated products #12;8 US Army Corps of Engineers® Engineer Research.5% or more in 2013 and beyond (DoD Internal Guidance is 25% by 2025) ­ Energy Efficient Products ­ Install · Renewable, Renewable, Renewable · Net Zero Energy ­ Energy Efficiency (Conservation) ­ Energy Production

466

RESEARCH AND ENGINEERING COMPANY  

Office of Legacy Management (LM)

?' $ 5 . . 7 pi -ON RESEARCH AND ENGINEERING COMPANY CLINTON TOWNSHIP, ROUTE 22 EAST, ANNANDALE, NEW iERSEY 08801 July 18, 1988 Mr. Ken Wills Weston/OTS 20030 Century Blvd Suite 301 Germantown, MD 20874 Dear Ken, Per our conversation on July 11, 1988, enclosed is a current plot plan of the Linden Technology Center (old Standard Oil Development Company site). I hope this satisfies your in- formation needs regarding the study you are doing concerning AEC contractor sites. We believe we have provided Mr. Charles young with all the information he required. If you have further questions, please call me at (2011 730-3053. Very truly yours, I Paul C. Bucknam PCB:bam Enclosure 07188Ol.pcb LINDEN TECHNOLOGY CENTER. LINDEN, N.J. VISITORS PARKING PLAN YOU ARE HERE WE HOPE YOUR VISIT WILL BE PRODUCTIVE AND SAFE

467

Image Content Engine (ICE)  

SciTech Connect

The Image Content Engine (ICE) is being developed to provide cueing assistance to human image analysts faced with increasingly large and intractable amounts of image data. The ICE architecture includes user configurable feature extraction pipelines which produce intermediate feature vector and match surface files which can then be accessed by interactive relational queries. Application of the feature extraction algorithms to large collections of images may be extremely time consuming and is launched as a batch job on a Linux cluster. The query interface accesses only the intermediate files and returns candidate hits nearly instantaneously. Queries may be posed for individual objects or collections. The query interface prompts the user for feedback, and applies relevance feedback algorithms to revise the feature vector weighting and focus on relevant search results. Examples of feature extraction and both model-based and search-by-example queries are presented.

Brase, J M

2007-03-26T23:59:59.000Z

468

Inorganic polymer engineering materials  

Science Conference Proceedings (OSTI)

Phosphazene-based, inorganic-polymer composites have been produced and evaluated as potential engineering materials. The thermal, chemical, and mechanical properties of several different composites made from one polymer formulation have been measured. Measured properties are very good, and the composites show excellent promise for structural applications in harsh environments. Chopped fiberglass, mineral, cellulose, and woodflour filled composites were tested. Chopped fiberglass filled composites showed the best overall properties. The phosphazene composites are very hard and rigid. They have low dielectric constants and typical linear thermal expansion coefficients for polymers. In most cases, the phosphazene materials performed as well or better than analogous, commercially available, filled phenolic composites. After 3 to 5 weeks of exposure, both the phosphazene and phenolics were degraded to aqueous bases and acids. The glass filled phosphazene samples were least affected.

Stone, M.L.

1993-06-01T23:59:59.000Z

469

REDUCED ENGINE FRICTION AND WEAR  

DOE Green Energy (OSTI)

This Final Technical Report discusses the progress was made on the experimental and numerical tasks over the duration of this project regarding a new technique for decreasing engine friction and wear via liner rotation. The experimental subtasks involved quantifying the reduction in engine friction for a prototype rotating liner engine relative to a comparable baseline engine. Both engine were single cylinder conversions of nominally identical production four-cylinder engines. Hot motoring tests were conducted initially and revealed that liner rotation decreased engine friction by 20% under motoring conditions. A well-established model was used to estimate that liner rotation should decrease the friction of a four-cylinder engine by 40% under hot motoring conditions. Hot motoring tear-down tests revealed that the crankshaft and valve train frictional losses were essentially the same for the two engines, as expected. However, the rotating liner engine had much lower (>70%) piston assembly friction compared to the conventional engine. Finally, we used the Instantaneous IMEP method to compare the crank-angle resolved piston assembly friction for the two engines. Under hot motoring conditions, these measurements revealed a significant reduction in piston assembly friction, especially in the vicinity of compression TDC when the lubrication regime transitions from hydrodynamic through mixed and into boundary friction. We have some remaining problems with these measurements that we expect to solve during the next few weeks. We will then perform these measurements under firing conditions. We also proposed to improve the state-of-the-art of numerical modeling of piston assembly friction for conventional engines and then to extend this model to rotating liner engines. Our research team first modeled a single ring in the Purdue ring-liner test rig. Our model showed good agreement with the test rig data for a range of speeds and loads. We then modeled a complete piston assembly in an engine. The model appears to produce the correct behavior, but we cannot quantify its strengths or weaknesses until our crank-angle-resolved measurements have been completed. Finally, we proposed and implemented a model for the effects of liner rotation on piston assembly friction. Here, we propose that the rotating liner design is analogous to the shaft-bushing mechanism. Therefore, we used the side-slip rolling friction model to simulate the effects of liner rotation. This model appears to be promising, but final analysis of its strengths and/or weaknesses must await our crank-angle-resolved measurements.

Ron Matthews

2005-05-01T23:59:59.000Z

470

Exciting youth about science and engineering : the Stirling Engine class; Stirling Engine class.  

E-Print Network (OSTI)

??The problem of a lack of science and engineering opportunities for youth has been identified. While other programs and attempted solutions exist, a novel approach (more)

Barragn, Patrick R

2008-01-01T23:59:59.000Z

471

Regional characteristics, timing, and significance of dissolution and collapse features in Lower Cretaceous carbonate platform strata, Desoto Canyon area, offshore Alabama-Florida  

E-Print Network (OSTI)

Lower Cretaceous carbonate strata from the central DeSoto Canyon area, offshore Alabama and Florida were studied to determine the extent, intensity, and controlling factors on dissolution-collapse features within these strata. The collapsed zones across the study area were mapped using a tight 2-D seismic grid. The zones of dissolution-collapse form a crude rectilinear pattern in plan view with the average trend of more elongated sections of the dissolution features being subparallel to regional southwestward dip on the Lower Cretaceous platform. Larger collapse features developed near the modern erosional margin that defines the seaward limit of the Lower Cretaceous platform in the study area. Middle Cretaceous strata up to approximately the Coniacian-Santonian unconformity (middle Late Cretaceous age) have numerous compaction-related faults around sagged areas above apparent dissolution-collapse zones within Lower Cretaceous strata. Bi-directional stratal onlap into the collapsed and sagged zones is only found above the Coniacian-Santonian unconformity. These relationships suggest a regional confined freshwater aquifer system developed within the Lower Cretaceous interval at about Coniacian-Santonian time when meteoric groundwater likely flowed from recharge areas to the north in central Alabama and discharged along the western erosional escarpment of the Lower Cretaceous platform. This meteoric groundwater may have mixed either with seawater that infiltrated the platform from the escarpment edge or with hydrogen-sulfide-rich basinal fluids that migrated to structurally high areas (where the dissolution-collapse zones are found). Alternatively, some combination of these mixing processes may have been responsible for the intense and likely still ongoing dissolution in this area of the Lower Cretaceous carbonate platform.

Iannello, Christine

2001-01-01T23:59:59.000Z

472

Characterization of the 3-D Properties of the Fine-Grained Turbidite 8 Sand Reservoir, Green Canyon 18, Gulf of Mexico  

E-Print Network (OSTI)

Understanding the internal organization of the Lower Pleistocene 8 Sand reservoir in the Green Canyon 18 field, Gulf of Mexico, helps to increase knowledge of the geology and the petrophysical properties, and hence contribute to production management in the area. Interpretation of log data from 29 wells, core and production data served to detail as much as possible a geological model destined for a future reservoir simulation. Core data showed that the main facies resulting from fine-grained turbidity currents is composed of alternating sand and shale layers, whose extension is assumed to be large. They correspond to levee and overbank deposits that are usually associated to channel systems. The high porosity values, coming from unconsolidated sediment, were associated to high horizontal permeability but generally low kv/kh ratio. The location of channel deposits was not obvious but thickness maps suggested that two main systems, with a northwest-southeast direction, contributed to the 8 Sand formation deposition. These two systems were not active at the same time and one of them was probably eroded by overlying formations. Spatial relationships between them remained unclear. Shingled stacking of the channel deposits resulted from lateral migration of narrow, meandering leveed channels in the mid part of the turbidite system. Then salt tectonics tilted turbidite deposits and led to the actual structure of the reservoir. The sedimentary analysis allowed the discrimination of three facies A, B and E, with given porosity and permeability values, that corresponded to channel, levee and overbank deposits. They were used to populate the reservoir model. Well correlation helped figure out the extension of these facies.

Plantevin, Matthieu Francois

2003-05-01T23:59:59.000Z

473

Vanderbilt Department of Mechanical Engineering  

E-Print Network (OSTI)

C A T I O N Stirling engine design #12;27 "I'm not the same person I was one-and-a-half years ago. I display Stirling engine components. Front - Eric Clarke, l to r- Dan Cordon, Nathaniel Allen, Dan Gerbus

Simaan, Nabil

474

Wind Engineering & Natural Disaster Mitigation  

E-Print Network (OSTI)

Wind Engineering & Natural Disaster Mitigation For more than 45 years, Western University has been internationally recognized as the leading university for wind engineering and wind- related research. Its of environmental disaster mitigation, with specific strengths in wind and earthquake research. Boundary Layer Wind

Sinnamon, Gordon J.

475

Civil & Environmental Engineering Student Handbook  

E-Print Network (OSTI)

1 Civil & Environmental Engineering Student Handbook Fall 2013/Spring 2014 WELCOME Welcome to the Department of Civil and Environmental Engineering. The intent of this Handbook is to introduce you to the Department, the faculty, and the undergraduate programs and activities. This Handbook also provides details

Massachusetts at Amherst, University of

476

Chemical Engineering and Materials Science  

E-Print Network (OSTI)

from vegetable oil. Earn a degree in chemical engineering, and you could enjoy a career working to commercialize new ideas, technologies and products. Students learn to solve problems and bring inventions through tissue engineering of large vessels and heart valves, or inventing clean-burning alternative fuel

Chinnam, Ratna Babu

477

Engineering and design Taught degrees  

E-Print Network (OSTI)

in Mechanical Engineering MSc in Satellite Communication Systems MSc in Sustainable Energy Technology Research, mathematics, physics or an applied science. Also refer to Applicant profile, listed with relevant course in Mechanical Engineering, the MSc in Sustainable Energy Technology or a research degree, we must receive your

Sussex, University of

478

Stirling engine with pressurized crankcase  

DOE Patents (OSTI)

A two piston Stirling engine wherein the pistons are coupled to a common crankshaft via bearing means, the pistons include pad means to minimize friction between the pistons and the cylinders during reciprocation of the pistons, means for pressurizing the engine crankcase, and means for cooling the crankshaft and the bearing means eliminating the need for oil in the crankcase.

Corey, John A. (Melrose, NY)

1988-01-01T23:59:59.000Z

479

Texas Tech University's New Petroleum Engineering Building  

E-Print Network (OSTI)

Texas Tech University's New Petroleum Engineering Building: A New Era in Petroleum Engineering Production and Operations Education Summer 2012 Engineering Our Future Texas Tech University - Edward E. Whitacre Jr. College of Engineering Texas Tech Makes Progress to Tier One Five Distinguished Engineers

Zhang, Yuanlin

480

IOWA STATE UNIVERSITY DEPARTMENTS OF MECHANICAL ENGINEERING,  

E-Print Network (OSTI)

of materials, and energy storage and conversion. Ju obtained a PhD degree in nuclear engineering from MIT Nuclear Engineering & Radiological Sciences And Materials Science & Engineering Present the First Annual of Nuclear Science and Engineering Department of Materials Science and Engineering "Plumber's Wonderland

Lin, Zhiqun

First Page Previous Page 1 2 3 4 5 6 7 8 9 10 11