Powered by Deep Web Technologies
Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

34th annual reed rotary rig census  

SciTech Connect

This article reports that the number of rigs active according to the 1986 census is 1052, which represents a decline of 1573 rigs from 1985 figures. This 60 percent decrease is the largest decline of active rigs in the 34-year history of the census. The 1986 census takers found 3993 rigs are available with the capacity to drill deeper than 3000 ft. The count has thus declined by 416 rigs (9 percent) from the 1985 total of 4409. Rig availability declined for the fourth consecutive year following nine straight years of fleet expansion (1974-1982). During the past four years, 1651 rigs have been removed from the drilling fleet representing a 29 percent decline from the record high number of rigs available in 1982. The 1986 decline in the available U.S. fleet is considerably less than what many industry observers had been anticipating. A larger decrease in the rig fleet has not been realized for a number of reasons.

Hutchinson, D.L.; Pastusek, P.E.

1986-10-01T23:59:59.000Z

2

Table 4.4 Crude Oil and Natural Gas Rotary Rigs in ...  

U.S. Energy Information Administration (EIA)

Table 4.4 Crude Oil and Natural Gas Rotary Rigs in Operation, 1949-2011 (Number of Rigs) Year: By Site : By Type: Total 1: Onshore

3

U.S. Offshore Crude Oil and Natural Gas Rotary Rigs in Operation ...  

U.S. Energy Information Administration (EIA)

U.S. Offshore Crude Oil and Natural Gas Rotary Rigs in Operation (Number of Elements) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec; 1973: 99: 89: 90: 79: 72 ...

4

U.S. Offshore Crude Oil and Natural Gas Rotary Rigs in Operation ...  

U.S. Energy Information Administration (EIA)

U.S. Offshore Crude Oil and Natural Gas Rotary Rigs in Operation (Number of Elements) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 ...

5

U.S. Crude Oil and Natural Gas Rotary Rigs in Operation (Number of ...  

U.S. Energy Information Administration (EIA)

U.S. Crude Oil and Natural Gas Rotary Rigs in Operation (Number of Elements) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec; 1973: 1,219: 1,126: 1,049: 993 ...

6

rig_specs.indd  

NLE Websites -- All DOE Office Websites (Extended Search)

RIG SPECIFICATIONS R MOTC Rig No. 1 is a 2005 Crown (Calgary, Canada) trailer-mounted drilling rig. It incor- porates several features found desirable over numerous drilling tests...

7

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

12-i Chapter 12 Rigging Hardware CHAPTER 12 RIGGING HARDWARE This chapter provides requirements for rigging accessories used in hoisting and rigging - shackles, eyebolts, eye nuts, links, rings, swivels, wire-rope clips, turnbuckles, rigging hooks, and load-indicating devices and implements the requirements of ANSI/ASME B30.26, "Rigging Hardware" (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 12.1 GENERAL..................................................................................................................................12-1 12.1.1 Good and Bad Rigging Practices ...................................................................................12-1 12.2 RIGGING HOOKS.....................................................................................................................12-5

8

Hoisting & Rigging Fundamentals  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hoisting and Rigging Hoisting and Rigging Fundamentals for Riaaers and ODerators Pendant Control - Components TR244C, Rev. 5 December 2002 TR244C Rev . 5 TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii HOISTING AND RIGGING OBJECTIVES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 WIRE ROPE SLINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SYNTHETIC WEBBING SLINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I O CHAINSLINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 METAL MESH SLINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 SPREADER BEAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 RIGGING HARDWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9

Hoisting & Rigging Lift Plan  

NLE Websites -- All DOE Office Websites (Extended Search)

Authorized Personnel (attach more sheets if necessary) Printed name Signature Date SSRL Hoisting & Rigging Lift Plan Stanford Synchrotron Radiation Laboratory May 16, 2005...

10

A rigged market  

SciTech Connect

The mobile rig market remains a unique sector of the global upstream oil and gas industry. Big oil is continuing to emerge blinking from the darkness of its recent cash-starved existence to bask in the glory of a resurgent oil price. But the rig sector is once again lagging behind the pace being set by operators as they open up their wallets for new or delayed exploration and production projects. This paper gives statistics on worldwide count and contracts.

Thomas, M.

2000-02-01T23:59:59.000Z

11

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE-STD-1090-2011 DOE-STD-1090-2011 September 2011 Superseding DOE-STD-1090-2007 August 2007 DOE STANDARD HOISTING AND RIGGING U.S. Department of Energy AREA SAFT Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. INCH-POUND INTENTIONALLY BLANK DOE-STD-1090-2011 iii Introduction The U.S. Department of Energy (DOE) Hoisting and Rigging Standard is intended to be used by supervisors, line managers, safety personnel, equipment operators, riggers and other personnel responsible for the safety of hoisting and rigging operations at DOE sites. It may be used as either contract document or as a best practices guide at the site's or program office's discretion. The standard invokes applicable OSHA and national consensus standards but also delineates

12

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

13-i CHAPTER 13 LOAD HOOKS This chapter provides safety standards for the inspection, testing, and maintenance of load hooks installed on cranes or hoists and implements the requirements of ASME B30.10, Chapter 10-1, "Hooks." See Chapter 12, "Rigging Accessories," for rigging hook requirements (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 13.1 GENERAL ...............................................................................................................................13-1 13.1.1 Marking......................................................................................................................13-1 13.1.2 Attachments ...............................................................................................................13-1

13

Program: Hoisting and Rigging  

E-Print Network (OSTI)

The purpose of these requirements is to ensure that hoisting and rigging (H&R) equipment is safe to operate. 2 Scope These requirements cover inspections and maintenance over the life of H&R equipment. Requirements are listed in terms of ? Types of inspection (initial, pre-use, frequent, periodic, and third party) and maintenance (preventative, operational testing, and load testing) Responsibilities (person who ensures that the inspection was performed and person performing the inspection) Documentation requirements – HRED refers to the H&R Equipment Database, which is maintained by the H&R inspector. Submit inspection and maintenance data to this inspector to stay in compliance. – CR refers to custodian records, which are maintained by the equipment custodian. Details on what to look for and how to conduct the inspection are listed in Department of Energy Standard 1090, “Hoisting and Rigging ” (DOE-STD-1090-2007).

unknown authors

2009-01-01T23:59:59.000Z

14

Joint venture builds new rigs  

Science Conference Proceedings (OSTI)

Recent emphasis on increasing drilling efficiency and avoiding additional environmental damage has led Russian operator Gazprom to specify a new generation drilling rig for exploratory and development drilling in the Astrakhan gas/condensate field in southwestern Russia. The two rigs on order combine Russian and American technology and include a unique system for processing contaminated drill cuttings. The article describes the rig package and cuttings treatment system.

NONE

1995-05-01T23:59:59.000Z

15

Hoisting & Rigging Assessment Plan  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HOISTING & RIGGING HOISTING & RIGGING Assessment Plan NNSA/Nevada Site Office Facility Representative Division Performance Objective: To determine that hoisting and rigging operations are conducted according to "industry best standards" for increasing equipment reliability while assuring worker safety, and to verify issues being addressed in BN Hoisting assessment. Criteria: Lifts are identified and categorized appropriately for scheduled maintenance. DOE-STD-1090-2001 An integrated process ensures safety issues are identified and controls established. DOE-STD-1090-2001 Personnel operating and maintaining the hoisting equipment are trained; they understand their roles and responsibilities. DOE-STD-1090-2001 Maintenance conducts safety inspections of hoisting and rigging

16

Hoisting & Rigging Assessment Plan  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HOISTING & RIGGING HOISTING & RIGGING Assessment Plan NNSA/Nevada Site Office Facility Representative Division Performance Objective: To determine that hoisting and rigging operations are conducted according to "industry best standards" for increasing equipment reliability while assuring worker safety, and to verify issues being addressed in BN Hoisting assessment. Criteria: Lifts are identified and categorized appropriately for scheduled maintenance. DOE-STD-1090-2001 An integrated process ensures safety issues are identified and controls established. DOE-STD-1090-2001 Personnel operating and maintaining the hoisting equipment are trained; they understand their roles and responsibilities. DOE-STD-1090-2001 Maintenance conducts safety inspections of hoisting and rigging

17

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1-i 1-i CHAPTER 11 WIRE ROPE AND SLINGS This chapter provides requirements for the fabrication and use of wire rope and slings used in hoisting and rigging and implements the requirements of ASME B30.9, Slings (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). . 11.1 GENERAL ...............................................................................................................................11-1 11.2 WIRE ROPE ............................................................................................................................11-4 11.2.1 Wire-Rope Lays .........................................................................................................11-4 11.2.2 Wire-Rope Cores .......................................................................................................11-4

18

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 BELOW-THE-HOOK LIFTING DEVICES 14-i This chapter provides the requirements for below-the-hook lifting devices used in hoisting and rigging, such as spreader bars, lifting yokes, and lift fixtures. This section implements the requirements of ASME B30.20, "Below-the-Hook Lifting Devices" (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). NOTE: Special lifting devices for shipping containers weighing 10,000 lb or more that are used for radioactive materials are governed by ANSI N14.6 ["Standard for Special Lifting Devices for Shipping Containers Weighing 10,000 Pounds (4,500 kg) or More for Nuclear Materials."] 14.1 GENERAL ...............................................................................................................................14-1

19

Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

SciTech Connect

This standard is intended as a reference document to be used by supervisors, line managers, safety personnel, equipment operators, and any other personnel responsible for safety of hoisting and rigging operations at DOE sites. It quotes or paraphrases the US OSHA and ANSI requirements. It also encompasses, under one cover,hoisting and rigging requirements, codes, standards, and regulations, eliminating the need to maintain extensive (and often incomplete) libraries of hoisting and rigging standards throughout DOE. The standard occasionally goes beyond the minimum general industry standards established by OSHA and ANSI, and also delineates the more stringent requirements necessary to accomplish the complex, diversified, critical, and often hazardous hoisting and rigging work found with the DOE complex.

NONE

1995-06-01T23:59:59.000Z

20

Hoisting and Rigging: Inspection and Maintenance Requirements  

E-Print Network (OSTI)

Devices, Slings, and Rigging Hardware and Accessories (SLAC-I-730-0A21S-036) Hoisting and Rigging: PreHoisting and Rigging: Inspection and Maintenance Requirements URL: http://www-group.slac.stanford.edu/esh/eshmanual/references/hoisting Department: Field Safety and Building Inspection Program: Hoisting and Rigging Authority: ESH Manual, Chapter

Wechsler, Risa H.

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9-2004 9-2004 12-i Chapter 12 Rigging Accessories CHAPTER 12 RIGGING ACCESSORIES This chapter provides requirements for rigging accessories used in hoisting and rigging - shackles, eyebolts, rings, wire-rope clips, turnbuckles, rigging hooks, and load-indicating devices. 12.1 GENERAL ...............................................................................................................................12-1 12.1.1 Inspections .................................................................................................................12-1 12.1.2 Testing .....................................................................................................................12-3 12.1.3 Good and Bad Rigging Practices ...............................................................................12-3

22

Hoisting and rigging manual: Uncontrolled document  

Science Conference Proceedings (OSTI)

This document is a draft copy of a Hoisting and Rigging Manual for the Department of Energy. The manual is divided into ten chapters. The chapter titles follow: terminology and definitions; operator training and qualification; overhead and gantry cranes; mobile cranes; forklift trucks; hoists; hooks; wire rope, slings, and rigging accessories; construction hoisting and rigging equipment requirements; references.

NONE

1991-05-01T23:59:59.000Z

23

PNNL Hoisting and Rigging Manual  

Science Conference Proceedings (OSTI)

This manual describes the safe and cost effective operation, inspection, maintenance, and repair requirements for cranes, hoists, fork trucks, slings, rigging hardware, and hoisting equipment. It is intended to be a user's guide to requirements, codes, laws, regulations, standards, and practices that apply to Pacific Northwest National Laboratory (PNNL) and its subcontractors.

Haynie, Todd O.; Fullmer, Michael W.

2008-12-29T23:59:59.000Z

24

Hoisting & Rigging Lift Plan  

NLE Websites -- All DOE Office Websites (Extended Search)

Hoisting & Rigging Lift Plan Hoisting & Rigging Lift Plan Stanford Synchrotron Radiation Laboratory May 16, 2005 SSRL-HRLP-000-R0 Page 1 of 3 General Information Lift Plan Document # Plan prepared by: Describe the load or items to be lifted: Could the load, if dropped, release hazardous materials or radioactivity? No Yes (describe) Is the load irreplaceable or would it be very costly to replace if damaged? No Yes (describe) Brief description of lift activities (specify if rolling or flipping involved) Equipment Information Equipment ID: Equipment custodian: Rated capacity: Operator capacity : Personnel Protective Equipment (PPE) Steel-toed shoes Required for all personnel involved with lift activity to protect from crushing of feet/toes

25

Somebody better find some rigs  

SciTech Connect

The paper discusses the outlook for the gas and oil industries of the Middle East. Field development projects abound, as the larger exporting nations pursue ambitious policies of production expansion. However, their plans may be hampered by the growing worldwide shortage of rigs. Separate evaluations are given for Saudi Arabia, Kuwait, Neutral Zone, Abu Dhabi, Iran, Iraq, Qatar, Yemen, Syria, Dubai, Turkey, Sharjah, and briefly for Bahrain, Israel, Jordan, UAE-Ajman, and UAE-Ras al-Khaimah.

NONE

1997-08-01T23:59:59.000Z

26

Modular designs highlight several new rigs  

SciTech Connect

A new platform drilling rig for offshore Trinidad and two new land rigs for the former Soviet Union feature the latest in drilling and construction technology and modular components for quick rig up/rig down. The Sundowner 801 was mock-up tested in Galveston, TX, a few weeks ago in preparation for its load-out to the Dolphin field offshore Trinidad. Two other new units, UNOC 500 DE series land rigs, were recently constructed and mock-up tested in Ekaterinburg, Russia, for upcoming exploratory work for RAO Gazprom, a large natural gas producer in Russia. These rigs are unique in that they were constructed from new components made both in the US and in Russia. The paper describes all three units.

Rappold, K.

1995-12-04T23:59:59.000Z

27

Scheduling Workover Rigs for Onshore Oil Production  

E-Print Network (OSTI)

available workover rigs, so as to minimize the production loss associated with the ... novic [5, 6, 7] is based on the exploration of a dynamic neighborhood model.

28

Scheduling workover rigs for onshore oil production  

Science Conference Proceedings (OSTI)

Many oil wells in Brazilian onshore fields rely on artificial lift methods. Maintenance services such as cleaning, reinstatement, stimulation and others are essential to these wells. These services are performed by workover rigs, which are available ... Keywords: Combinatorial optimization, Heuristics, Oil production, VNS, Workover rigs

Dario J. Aloise; Daniel Aloise; Caroline T. M. Rocha; Celso C. Ribeiro; José C. Ribeiro Filho; Luiz S. S. Moura

2006-04-01T23:59:59.000Z

29

Operators wary: Stack that rig correctly  

SciTech Connect

This article points out that reasons for planned, scheduled preservation of offshore rigs and equipment are as varied as the owner's interest in them. As a result, no single plan or procedure can meet the requirements of every rig owner. Each rig and its equipment must be treated individually for a number of reasons. The most effective and economical rig preservation program is the result of both the owner and preservation contractor understanding all the objectives and the time frame involved. Numerous questions should be answered up front. How long will preservation measures be required. Is the rig to be maintained in an operational state. Will there be frequent trips to the rig. Will the unit be kept intact, or equipment removed as needed for operation of other rigs. Is the whole unit or any of its components for sale. Will insurance and certifications be affected by the preservation methods used. Perhaps most important is the time period. If the rig is to be stacked for an extended length of time, the owner will likely opt for ''cold,'' or inoperable, preservation. In this condition, engines are treated to protect cylinders, cooling systems and drive components in a static condition.

Moriniere, J.

1987-07-01T23:59:59.000Z

30

Study on an Electric Drilling Rig with Hydraulic Energy Storage  

Science Conference Proceedings (OSTI)

An electric drilling rig with hydraulic energy storage is researched. This rig can recover the potential energy of the drill stem lowered and owns remarkable energy-saving effect. The mathematical model of the new rig lifting the drill stem was deduced ... Keywords: electric drilling rig, energy-recovering, energy-saving

Zhang Lujun

2010-06-01T23:59:59.000Z

31

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 CONSTRUCTION HOISTING AND RIGGING EQUIPMENT REQUIREMENTS 15-i Chapter 15 Construction Hoisting and Rigging Equipment Requirements This chapter outlines the requirements for the safe use of hoisting and rigging equipment on construction projects at DOE installations. 15.1 GENERAL ...............................................................................................................................15-1 15.2 PERSONNEL QUALIFICATIONS.........................................................................................15-2 15.2.1 Qualified Operators of Mobile Cranes.......................................................................15-2 15.2.2 Qualified Operators of Forklift Trucks ......................................................................15-3

32

Toolpusher is key to efficient rig operation  

Science Conference Proceedings (OSTI)

Toolpushers earn a higher salary, control more personnel, and are responsible for a more expensive operation than many graduate MBAs. As a result, toolpushers are key to improved rig efficiencies and reduced crew turnover. For example, by having its toolpushers in Libya implement a new managerial approach, Santa Fe Drilling Co. reduced labor turnover 30%, reduced the number of lost-time accidents 58%, and increased average rig inspection scores 6%. During the boom years of drilling, toolpushers complained often about the poor quality of roustabouts and roughnecks assigned to them. Many toolpushers held poor screening of personnel responsible, and felt justified in firing those who were slow to adapt. Few of them considered that they were directly responsible. Today's toolpusher must realize that he is responsible not only for the rig, its maintenance, and its drilling performance, but for training and development of the rig's personnel as well.

Fortney, K.

1983-09-01T23:59:59.000Z

33

Unique rig designed for northern areas  

SciTech Connect

The development of a new generation of drilling and support vessels specially designed to allow year-round drilling off the northern coast of Norway is discussed. New and better equipment is necessary so year-round operations can be done safely and without danger to the environment. To achieve that, a specially designed drilling rig, as well as support and standby vessels are being developed. A quantitative safety analysis of the rig is presently being carried out. The rig will be highly computerized. The computer software will contain programs for stability calculation, ballast recommendation, automatic trim, automatic ballast, automatic mud mix, strain/stress monitoring, dynamic stability, warehouse/maintenance and drilling data acquisition.

1984-05-01T23:59:59.000Z

34

Self propelled drilling rig starts offshore exploration  

SciTech Connect

Ocean Drilling and Exploration Co. recently commissioned its new $12 million self-propelled, semisubmersible drilling rig, Ocean Prospector, at Mitsubishi Shipyard, Japan, where the rig was built. Initial trail runs completed adjacent to the shipyard indicated that the ship has a speed of 7 kn ahead and 3 kn astern. Steering also is reported to be excellent. The rig has a minimum turning radius of approx. 2 barge lengths and shows instant response. This rig is powered by 4 Fairbanks Morse, 10-cylinder opposed piston, model 38D8-1/8 diesel engines. Each engine is rated at 1,600 hp at 720 rpm and they drive eight 1,600 kw, traction type D-C generators and two 1,000 kw A-C generators. The rated operating depth of the unit afloat is 600 ft of water. The overall length of Ocean Prospector is just over 344 ft, with the beam measuring 263-1/2 ft. During transit, when the rig will be completely deballasted, it will have a draft of approx. 20 ft. When it reaches the drilling site, ballast water will be pumped into the 18 ballast tanks until the draft is increased to 70 ft. At this point, the underside of the main deck will be 50 ft above the mean surface of the sea. Drilling operations will be conducted while the rig is at the 70 ft draft. The mooring system will consist of eight 2-3/4 in. chains, each measuring 3,300 ft in length and connected to a 15-ton anchor.

1971-05-01T23:59:59.000Z

35

Rig scarcity prompts innovative drilling solution  

Science Conference Proceedings (OSTI)

Unable to locate a shallow-water offshore rig for its program in Indonesia, British Gas International developed an innovative pad/ballasted barge configuration to utilize a land rig, which was available. Many non-typical problems were encountered and solved to establish the drilling location 600 m (2,000 ft) from the shore in Bintuni Bay in Irian Jaya, eastern Indonesia. The final hybrid configuration has sparked interesting debate as to whether the operation should be designated as onshore or offshore. The paper discusses the project overview, concept development, construction, and operations.

Lattimore, G.M.; Gott, T.; Feagin, J.

1997-11-01T23:59:59.000Z

36

ADVANCED HOT SECTION MATERIALS AND COATINGS TEST RIG  

SciTech Connect

The Hyperbaric Advanced Hot Section Materials & Coating Test Rig program provides design and implementation of a laboratory rig capable of simulating the hot gas path conditions of coal-gas fired industrial gas turbine engines. The principal activity during this reporting period were the evaluation of syngas combustor concepts, the evaluation of test section concepts and the selection of the preferred rig configuration.

Scott Reome; Dan Davies

2004-04-30T23:59:59.000Z

37

DOE-STD-1090-99; DOE Standard Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

NLE Websites -- All DOE Office Websites (Extended Search)

TS TS INCH-POUND DOE-STD-1090-99 March 1999 Superseding DOE-STD-1090-96 September 1996 DOE STANDARD HOISTING AND RIGGING (Formerly Hoisting and Rigging Manual) U.S. Department of Energy AREA SAFT Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. This document has been reproduced from the best available copy. Available to DOE and DOE contractors from ES&H Technical Information Services, U.S. Department of Energy, (800) 473-4375, fax: (301) 903-9823. Available to the public from the U.S. Department of Commerce, Technology Administration, National Technical Information Service, Springfield, VA 22161; (703) 605-6000. DOE STANDARD HOISTING AND RIGGING (Formerly Hoisting and Rigging Manual) Summary of Changes as of March 1999

38

Mixed Stream Test Rig (MISTER) Startup Report  

DOE Green Energy (OSTI)

This report describes the work accomplished to date to design, procure, assemble, authorize, and startup the Mixed Stream Test Rig (MISTER) at the Idaho National Laboratory (INL). It describes the reasons for establishing this capability, physical configuration of the test equipment, operations methodology, initial success, and plans for completing the initial 1,000 hour test.

Charles Park

2011-02-01T23:59:59.000Z

39

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 CONSTRUCTION HOISTING AND RIGGING EQUIPMENT REQUIREMENTS 15-i This chapter outlines the requirements for the safe use of hoisting and rigging equipment on construction projects at DOE installations. 15.1 GENERAL ...............................................................................................................................15-1 15.2 PERSONNEL QUALIFICATIONS.........................................................................................15-2 15.2.1 Qualified Operators of Mobile Cranes.......................................................................15-2 15.2.2 Qualified Operators of Forklift Trucks ......................................................................15-3 15.2.3 Qualified Riggers .......................................................................................................15-4

40

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 LOAD HOOKS 13-i Chapter 13 Load Hooks This chapter provides safety standards for the inspection, testing, and maintenance of load hooks installed on cranes or hoists and implements the requirements of ASME B30.10, Chapter 10-1, "Hooks." See Chapter 12, "Rigging Accessories," for rigging hook requirements. 13.1 GENERAL ...............................................................................................................................13-1 13.1.1 Marking......................................................................................................................13-1 13.1.2 Attachments ...............................................................................................................13-1

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Hoisting and Rigging: Pre-use Inspection Criteria for Below-the-Hook Lifting Devices, Slings, and Rigging  

E-Print Network (OSTI)

, and Rigging Hardware and Accessories URL: http://www-group.slac.stanford.edu/esh/eshmanual/references/hoistingHoisting and Rigging: Pre-use Inspection Criteria for Below-the-Hook Lifting Devices, Slings Department: Field Safety and Building Inspection Program: Hoisting and Rigging Authority: ESH Manual, Chapter

Wechsler, Risa H.

42

Surveillance Guide - CPS 8.1 Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HOISTING AND RIGGING HOISTING AND RIGGING 1.0 Objective The objective of this surveillance is to examine hoisting and rigging operations to ensure that safe equipment and work practices are being used. The surveillance includes verification that hoisting and rigging work is performed in accordance with DOE requirements and best practices. 2.0 References 2.1 DOE O 440.1A, Worker Protection Management For Doe Federal And Contractor Employees 2.2 DOE-RL-92-36, Hanford Site Hoisting and Rigging Manual NOTE The DOE Hoisting and Rigging Manual should be used as the primary reference for this surveillance. 1 3.0 Requirements Implemented This surveillance is conducted to implement the RL Functions, Responsibilities, and Authorities Manual (FRAM) item No. 2504. 4.0 Surveillance Activities

43

MHK Technologies/Ocean Energy Rig | Open Energy Information  

Open Energy Info (EERE)

Rig Rig < MHK Technologies Jump to: navigation, search << Return to the MHK database homepage Ocean Energy Rig.jpg Technology Profile Primary Organization Free Flow 69 Technology Resource Click here Current Technology Type Click here Axial Flow Turbine Technology Readiness Level Click here TRL 4 Proof of Concept Technology Description The Ocean Energy Rig is a hybrid concept harnessing tidal stream with increased velocity from venturi system wave and wind power The rig also uses solar panels to power computers and warning lights Other unique features include a water ballasting system with automatic self levelling and wave ramps to maximize FreeFlow 69 s new wave power device It is envisaged that the Ocean Energy Rig would be assembled and maintained in dry docks and would be towed out into position before being semi submerged and anchored for operation Power output of the production model would be at least 10MW

44

NETL: News Release - DOE-Funded 'Microhole' Drilling Rig Demonstrated...  

NLE Websites -- All DOE Office Websites (Extended Search)

Rig Demonstrated Successfully in Midcontinent New Technology Initiative Slashes Drilling Costs, Benefits Environment, Energy Security WASHINGTON, DC - A U.S. Department of...

45

Optimization Online - Scheduling Workover Rigs for Onshore Oil ...  

E-Print Network (OSTI)

Oct 12, 2003 ... Scheduling Workover Rigs for Onshore Oil Production. Dario Aloise (dario ***at** * dimap.ufrn.br) Daniel Aloise (aloise ***at*** inf.puc-rio.br)

46

Field Demonstraton of Existing Microhole Coiled Tubing Rig (MCTR) Technology  

SciTech Connect

The performance of an advanced Microhole Coiled Tubing Rig (MCTR) has been measured in the field during the drilling of 25 test wells in the Niobrara formation of Western Kansas and Eastern Colorado. The coiled tubing (CT) rig designed, built and operated by Advanced Drilling Technologies (ADT), was documented in its performance by GTI staff in the course of drilling wells ranging in depth from 500 to nearly 3,000 feet. Access to well sites in the Niobrara for documenting CT rig performance was provided by Rosewood Resources of Arlington, VA. The ADT CT rig was selected for field performance evaluation because it is one of the most advanced commercial CT rig designs that demonstrate a high degree of process integration and ease of set-up and operation. Employing an information collection protocol, data was collected from the ADT CT rig during 25 drilling events that encompassed a wide range of depths and drilling conditions in the Niobrara. Information collected included time-function data, selected parametric information indicating CT rig operational conditions, staffing levels, and field observations of the CT rig in each phase of operation, from rig up to rig down. The data obtained in this field evaluation indicates that the ADT CT rig exhibited excellent performance in the drilling and completion of more than 25 wells in the Niobrara under varied drilling depths and formation conditions. In the majority of the 25 project well drilling events, ROP values ranged between 300 and 620 feet per hour. For all but the lowest 2 wells, ROP values averaged approximately 400 feet per hour, representing an excellent drilling capability. Most wells of depths between 500 and 2,000 feet were drilled at a total functional rig time of less than 16 hours; for wells as deep at 2,500 to 3,000 feet, the total rig time for the CT unit is usually well under one day. About 40-55 percent of the functional rig time is divided evenly between drilling and casing/cementing. The balance of time is divided among the remaining four functions of rig up/rig down, logging, lay down bottomhole assembly, and pick up bottomhole assembly. Observations made during all phases of CT rig operation at each of the project well installations have verified a number of characteristics of the technology that represent advantages that can produce significant savings of 25-35 percent per well. Attributes of the CT rig performance include: (1) Excellent hole quality with hole deviation amounting to 1-2 degrees; (2) Reduced need for auxiliary equipment; (3) Efficient rig mobilization requiring only four trailers; (4) Capability of ''Zero Discharge'' operation; (5) Improved safety; and, (6) Measurement while drilling capability. In addition, commercial cost data indicates that the CT rig reduces drilling costs by 25 to 35% compared to conventional drilling technology. Widespread commercial use of the Microhole Coiled Tubing technology in the United States for onshore Lower-48 drilling has the potential of achieving substantially positive impacts in terms of savings to the industry and resource expansion. Successfully commercialized Microhole CT Rig Technology is projected to achieve cumulative savings in Lower-48 onshore drilling expenditures of approximately 6.8 billion dollars by 2025. The reduced cost of CT microhole drilling is projected to enable the development of gas resources that would not have been economic with conventional methods. Because of the reduced cost of drilling achieved with CT rig technology, it is estimated that an additional 22 Tcf of gas resource will become economic to develop. In the future, the Microhole Coiled Tubing Rig represents an important platform for the continued improvement of drilling that draws on a new generation of various technologies to achieve goals of improved drilling cost and reduced impact to the environment.

Kent Perry; Samih Batarseh; Sheriff Gowelly; Thomas Hayes

2006-05-09T23:59:59.000Z

47

Design and construction of rigs for studying surface condensation and creating anodized metal oxide surfaces  

E-Print Network (OSTI)

This thesis details the design and construction of a rig for studying surface condensation and a rig for creating anodized metal oxides (AMOs). The condensation rig characterizes condensation for different surfaces; this ...

Sun, Wei-Yang

2011-01-01T23:59:59.000Z

48

C:\Documents and Settings\jhr\My Documents\C_drive\RIGS\users 2013\rigs_usersApril2013.vp  

Gasoline and Diesel Fuel Update (EIA)

23 23 Reserves Information Gathering System (RIGS) User's Guide Version 2013 For Report Year 2012 Energy Information Administration U.S. Department of Energy April 2013 Form EIA-23 Reserves Information Gathering System (RIGS) User's Guide April 2013 EIA-23 Reserves Information Gathering System (RIGS) User's Guide Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Hardware / Software Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installing the RIGS Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Using the EIA-23 Reserves Information Gathering System (RIGS) System . . . . . . . . . . . . . . . . . 4 Initial Data Import from Last Year's RIGS Submission File. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 The RIGS Main Menu Screen.

49

Rig upkeep vital in the downturn  

Science Conference Proceedings (OSTI)

As operations came to a close in 1982, many oil and gas contractors were facing the door of no return - subsequent years worsened matters. Drilling and workover units were returned to the lender and left stacked on and off location. Lending institutions began to weaken and, in some cases, collapse. However, many of the contractors with time and grade in providing contract drilling or workover services have had no desires or options other than to continue to operate in a downward spiraling market, much as they had done in the 50s and 60s. Operating under these circumstances requires a lot less flare and flame, and careful rearrangement of financial obligations. Contractors with equipment overloads reduced inventories and stacked the leftovers. This article shows that stacking or immobilizing a modern drilling rig or workover unit can be achieved economically. A sound preventive maintenance schedule can put the equipment on the stand-by board-ready to work. Several articles have been written on the ''new way to stack rigs.'' Most of these are simply a sensible realistic approach to maintaining a corporation's assets until they can be returned to the work force.

Leabo, J.H.

1987-05-01T23:59:59.000Z

50

Development of a portable grain mass flow sensor test rig  

Science Conference Proceedings (OSTI)

A portable grain mass flow sensor test rig was built to measure the accuracy of a mass flow sensor with dual use in the field as well as in the lab. Concurrently, a synchronization method was developed that employs GPS timing data to synchronize the ... Keywords: Mass flow sensor, Test rig, Yield monitor accuracy, Yield monitor error

M. Loghavi; R. Ehsani; R. Reeder

2008-05-01T23:59:59.000Z

51

Advanced Hot Section Materials and Coatings Test Rig  

SciTech Connect

The Hyperbaric Advanced Hot Section Materials & Coating Test Rig program provides design and implementation of a laboratory rig capable of simulating the hot gas path conditions of coal-gas fired industrial gas turbine engines. The principal activities during this reporting period were the continuation of test section detail design and developing specifications for auxiliary systems and facilities.

Dan Davies

2004-10-30T23:59:59.000Z

52

CRAD, Hoisting & Rigging Assessment Plan | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hoisting & Rigging Assessment Plan Hoisting & Rigging Assessment Plan CRAD, Hoisting & Rigging Assessment Plan Performance Objective: To determine that hoisting and rigging operations are conducted according to "industry best standards" for increasing equipment reliability while assuring worker safety, and to verify issues being addressed in BN Hoisting assessment. Criteria: Lifts are identified and categorized appropriately for scheduled maintenance. DOE-STD-1090-2001 An integrated process ensures safety issues are identified and controls established. DOE-STD-1090-2001 Personnel operating and maintaining the hoisting equipment are trained; they understand their roles and responsibilities. DOE-STD-1090-2001 Maintenance conducts safety inspections of hoisting and rigging equipment on a scheduled basis, certifying that safe operations are in

53

Advanced Hot Section Materials and Coatings Test Rig  

DOE Green Energy (OSTI)

Phase I of the Hyperbaric Advanced Hot Section Materials & Coating Test Rig Program has been successfully completed. Florida Turbine Technologies has designed and planned the implementation of a laboratory rig capable of simulating the hot gas path conditions of coal gas fired industrial gas turbine engines. Potential uses of this rig include investigations into environmental attack of turbine materials and coatings exposed to syngas, erosion, and thermal-mechanical fatigue. The principle activities during Phase 1 of this project included providing several conceptual designs for the test section, evaluating various syngas-fueled rig combustor concepts, comparing the various test section concepts and then selecting a configuration for detail design. Conceptual definition and requirements of auxiliary systems and facilities were also prepared. Implementation planning also progressed, with schedules prepared and future project milestones defined. The results of these tasks continue to show rig feasibility, both technically and economically.

Dan Davis

2006-09-30T23:59:59.000Z

54

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

11-i Chapter 11 11-i Chapter 11 Wire Rope and Slings CHAPTER 11 WIRE ROPE AND SLINGS This chapter provides requirements for the fabrication and use of wire rope and slings used in hoisting and rigging. 11.1 GENERAL ...............................................................................................................................11-1 11.2 WIRE ROPE ............................................................................................................................11-4 11.2.1 Wire-Rope Lays.........................................................................................................11-4 11.2.2 Wire-Rope Cores .......................................................................................................11-4 11.2.3 Wire Rope for General Purposes

55

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 HOSTILE ENVIRONMENTS 5-i Chapter 5 Hostile Environments This chapter describes provisions for hoisting and rigging operations in hostile work environments. 5.1 GENERAL ................................................................................................................................5-1 5.2 HOSTILE ENVIRONMENT PLAN ......................................................................................5-2 5.2.1 Marking and Posting ....................................................................................................5-2 5.2.2 Inspection and Testing .................................................................................................5-2 EXHIBIT I Hostile Environment Plan ............................................................................................5-3

56

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 HOSTILE ENVIRONMENTS 5-i Chapter 5 Hostile Environments This chapter describes provisions for hoisting and rigging operations in hostile work environments. 5.1 GENERAL................................................................................................................................5-1 5.2 HOSTILE ENVIRONMENT PLAN ......................................................................................5-2 5.2.1 Marking and Posting ....................................................................................................5-2 5.2.2 Inspection and Testing .................................................................................................5-2 EXHIBIT I Hostile Environment Plan ............................................................................................5-3

57

Hoisting & Rigging ISMS Assessment Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Objective: Assess the institutional and department/division hoisting and Objective: Assess the institutional and department/division hoisting and rigging (including forklift, overhead cranes small hoists, and mobile cranes) requirements, policies, procedures, and work practices for both professional and incidental activities. Review the roles and responsibilities of line managers, support personnel and workers who are involved in these activities as well as the adequacy of compliance with institutional and/or Department/Division qualifications, training requirements, and inspection requirements. Assess the laboratory's process for understanding the causes and development of effective corrective actions for incidents/accidents. Review the roles and responsibilities of line managers, support personnel and workers who are involved in the

58

Hoisting & Rigging ISMS Assessment Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Objective: Assess the institutional and department/division hoisting and Objective: Assess the institutional and department/division hoisting and rigging (including forklift, overhead cranes small hoists, and mobile cranes) requirements, policies, procedures, and work practices for both professional and incidental activities. Review the roles and responsibilities of line managers, support personnel and workers who are involved in these activities as well as the adequacy of compliance with institutional and/or Department/Division qualifications, training requirements, and inspection requirements. Assess the laboratory's process for understanding the causes and development of effective corrective actions for incidents/accidents. Review the roles and responsibilities of line managers, support personnel and workers who are involved in the

59

EIA-23L Reserves Information Gathering System (RIGS)  

Gasoline and Diesel Fuel Update (EIA)

EIA-23L Reserves Information Gathering System (RIGS) EIA-23L Reserves Information Gathering System (RIGS) Released: April 16, 2013 Background The Form EIA-23L, "Annual Survey of Domestic Oil and Gas Reserves, " is used to collect data on reserves of crude oil, natural gas, and natural gas liquids. These data are used to develop national and regional estimates of proved reserves of domestic crude oil, natural gas, and natural gas liquids, and to facilitate national energy policy decisions. Reporting on the Form EIA-23L is mandatory. Reserves Information Gathering System The Form EIA-23L Reserves Information Gathering System (RIGS), provides respondents with an efficient and effective means for filing the form using a personal computer (PC). Hardware / Software Requirements The minimum hardware requirements needed to install and use RIGS are:

60

Hoisting & Rigging Assessment Form | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hoisting & Rigging Assessment Form Hoisting & Rigging Assessment Form Hoisting & Rigging Assessment Form Assess the institutional and department/division hoisting and rigging (including forklift, overhead cranes small hoists, and mobile cranes) requirements, policies, procedures, and work practices for both professional and incidental activities. Review the roles and responsibilities of line managers, support personnel and workers who are involved in these activities as well as the adequacy of compliance with institutional and/or Department/Division qualifications, training requirements, and inspection requirements. Assess the laboratory's process for understanding the causes and development of effective corrective actions for incidents/accidents. Review the roles and responsibilities of line managers, support personnel and workers who are

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Guidelines for Using Synthetic Slings for Lifting and Rigging  

Science Conference Proceedings (OSTI)

"Guidelines for Using Synthetic Slings for Lifting and Rigging" provides nuclear and fossil maintenance personnel with information on the use of synthetic slings. This information will assist personnel in the identification, protection, and inspection of synthetic slings.

2003-02-10T23:59:59.000Z

62

ADVANCED HOT SECTION MATERIALS AND COATINGS TEST RIG  

SciTech Connect

The Hyperbaric Advanced Hot Section Materials & Coating Test Rig program initiated this quarter, provides design and implementation of a laboratory rig capable of simulating the hot gas path conditions of coal-gas fired industrial gas turbine engines. The principle activity during this first reporting period were preparing for and conducting a project kick-off meeting, working through plans for the project implementation, and beginning the conceptual design of the test section.

Scott Reome; Dan Davies

2004-01-01T23:59:59.000Z

63

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

TERMINOLOGY AND DEFINITIONS 1-1 Chapter 1 Terminology and Definitions The following are specialized terms commonly used when discussing hoisting and rigging operations. Many may not be used in this standard, but are included for general information. The terms are arranged in alphabetical order. Illustrations are included for clarity. ABRASION: Surface wear. ACCELERATION STRESS: Additional stress imposed due to increasing load velocity. ALTERNATE LAY: Lay of wire rope in which the strands are alternately regular and lang lay. ANSI: American National Standards Institute. APPOINTED: Assigned specific responsibilities by the employer or the employer's representative. AREA, METALLIC: Sum of the cross- sectional areas of individual wires in a wire rope

64

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

APPENDIX A PROCUREMENT GUIDELINES A-1 Appendix A Procurement Guidelines This appendix provides reference guidance in preparing purchase requisitions for hoisting and rigging materials and equipment. Nationally recognized standards and specifications are referenced for listed items. However, caution should be used prior to procurement of special items in order to verify appropriate specification or standard reference and requirements. Some specific requirements listed in this appendix are more restrictive than consensus standard requirements, but are recommended to ensure materials of adequate quality and workmanship are provided. Quality receipt inspections should be provided for all received materials in order to verify compliance of all

65

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

APPENDIX A APPENDIX A PROCUREMENT GUIDELINES A-i Appendix A Procurement Guidelines This appendix provides reference guidance in preparing purchase requisitions for hoisting and rigging materials and equipment. Nationally recognized standards and specifications are referenced for listed items. However, caution should be used prior to procurement of special items in order to verify appropriate specification or standard reference and requirements. Some specific requirements listed in this appendix are more restrictive than consensus standard requirements, but are recommended to ensure materials of adequate quality and workmanship are provided. Quality receipt inspections should be provided for all received materials in order to verify compliance of all

66

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

TERMINOLOGY AND DEFINITIONS 1-1 Chapter 1 Terminology and Definitions The following are specialized terms commonly used when discussing hoisting and rigging operations. Many may not be used in this standard, but are included for general information. The terms are arranged in alphabetical order. Illustrations are included for clarity. ABRASION: Surface wear. ACCELERATION STRESS: Additional stress imposed due to increasing load velocity. ALTERNATE LAY: Lay of wire rope in which the strands are alternately regular and lang lay. ANSI: American National Standards Institute. APPOINTED: Assigned specific responsibilities by the employer or the employer's representative. AREA, METALLIC: Sum of the cross- sectional areas of individual wires in a wire rope

67

Structural Insights into RNA Recognition by RIG-I  

Science Conference Proceedings (OSTI)

Intracellular RIG-I-like receptors (RLRs, including RIG-I, MDA-5, and LGP2) recognize viral RNAs as pathogen-associated molecular patterns (PAMPs) and initiate an antiviral immune response. To understand the molecular basis of this process, we determined the crystal structure of RIG-I in complex with double-stranded RNA (dsRNA). The dsRNA is sheathed within a network of protein domains that include a conserved 'helicase' domain (regions HEL1 and HEL2), a specialized insertion domain (HEL2i), and a C-terminal regulatory domain (CTD). A V-shaped pincer connects HEL2 and the CTD by gripping an {alpha}-helical shaft that extends from HEL1. In this way, the pincer coordinates functions of all the domains and couples RNA binding with ATP hydrolysis. RIG-I falls within the Dicer-RIG-I clade of the superfamily 2 helicases, and this structure reveals complex interplay between motor domains, accessory mechanical domains, and RNA that has implications for understanding the nanomechanical function of this protein family and other ATPases more broadly.

Luo, Dahai; Ding, Steve C.; Vela, Adriana; Kohlway, Andrew; Lindenbach, Brett D.; Pyle, Anna Marie (Yale)

2011-10-27T23:59:59.000Z

68

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 BELOW-THE-HOOK LIFTING DEVICES 14-i Chapter 14 Below-the-Hook Lifting Devices This chapter provides the requirements for below-the-hook lifting devices used in hoisting and rigging, such as spreader bars, lifting yokes, and lift fixtures. This section implements the requirements of ASME B30.20, "Below-the-Hook Lifting Devices." NOTE: Special lifting devices for shipping containers weighing 10,000 lb or more that are used for radioactive materials may be governed by ANSI N14.6 ["Standard for Special Lifting Devices for Shipping Containers Weighing 10,000 Pounds (4,500 kg) or More for Nuclear Materials."] 14.1 GENERAL ...............................................................................................................................14-1

69

Natural Gas for the Long Haul (Big Rigs Go Green)  

NLE Websites -- All DOE Office Websites (Extended Search)

the Long Haul (Big Rigs Go Green) the Long Haul (Big Rigs Go Green) JOHN DAVIS: No one has been hit harder by rising fuel prices than America's long-haul commercial truckers. A big rig can easily burn 20,000 gallons of fuel a year, and with diesel prices projected to keep rising, this not only pinches the trucker's bottom line, but that extra cost is passed on to American consumers. Meanwhile, natural gas prices have remained stable and are forecast to stay that way for years to come. Up to now, demand for natural gas as a transportation fuel has been mostly for compressed natural gas used by light and medium-duty vehicles. City buses, refuse haulers, utilities, and

70

Inventory management of steel plates at an oil rig construction company  

E-Print Network (OSTI)

Keppel Fels produces make-to-order oil exploration rigs for the global market. Each rig requires close to 6000 metric tons of steel in the course of its production. Optimal management of this steel is very critical in this ...

Tan, Chien Yung

2006-01-01T23:59:59.000Z

71

Planning and scheduling a fleet of rigs using simulation-optimization  

Science Conference Proceedings (OSTI)

Some of the most important and expensive activities in the oil field development and production phases relate to using rigs. These can be used for drilling wells, or for maintenance activities. As rigs are usually scarce compared to the number of wells ... Keywords: Planning, Rigs, Scheduling, Simulation-optimization

Hugo ViníCius Bassi; VirgíLio Jose Martins Ferreira Filho; Laura Bahiense

2012-12-01T23:59:59.000Z

72

Mixed Stream Test Rig Winter FY-2011 Report  

SciTech Connect

This report describes the data and analysis of the initial testing campaign of the Mixed Stream Test Rig (MISTER) at Idaho National Laboratory (INL). It describes the test specimen selection, physical configuration of the test equipment, operations methodology, and data and analysis of specimens exposed in two environments designed to represent those expected for high temperature steam electrolysis (HTSE).

Chalres Park; Tedd Lister; Kevin DeWall

2011-04-01T23:59:59.000Z

73

Diesel Rig Mechanical Peaking System Based on Flywheel Storage Technolgy  

Science Conference Proceedings (OSTI)

Flywheel energy storage technology is an emerging energy storage technology, there is a great development in recent years promising energy storage technology, with a large energy storage, high power, no pollution, use of broad, simple maintenance, enabling ... Keywords: Flywheel energy storage technology, mechanical peaking, diesel rig, peak motor

Shuguang Liu, Jia Wang

2012-07-01T23:59:59.000Z

74

Department of Energy Supercomputer Helps Design More Efficient Big Rigs |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Department of Energy Supercomputer Helps Design More Efficient Big Department of Energy Supercomputer Helps Design More Efficient Big Rigs Department of Energy Supercomputer Helps Design More Efficient Big Rigs February 8, 2011 - 12:00am Addthis Washington, DC - BMI Corporation, a company in South Carolina, in partnership with the Department of Energy's Oak Ridge National Laboratory (ORNL) has successfully developed a technology that will make semi trucks more fuel efficient with the potential to save millions of gallons of fuel. Utilizing the nation's most powerful computer, BMI Corp designed a SmartTruck UnderTray System, a set of integrated aerodynamic fairings that improve the aerodynamics of 18-wheeler (Class 8) long-haul trucks. If all 1.3 million Class 8 trucks in the U.S. were configured with these components, companies could achieve annual savings of 1.5 billion gallons

75

Rig count in Utica Shale doubles from year ago - Today in ...  

U.S. Energy Information Administration (EIA)

The number of active oil and natural gas rigs in the Appalachian Basin's Utica Shale formation for the last week of October 2012 (ending October 26) ...

76

CPS 8.1 Hoisting and Rigging, 2/25/2000  

Energy.gov (U.S. Department of Energy (DOE))

The objective of this surveillance is to examine hoisting and rigging operations to ensure that safe equipment and work practices are being used.  The surveillance includes verification that...

77

Design, Construction, and Preliminary Validation of the Turbine Reacting Flow Rig.  

E-Print Network (OSTI)

??This thesis presents the design, construction and partial operation of the Turbine Reacting Flow Rig (TuRFR), which is a high temperature turbine vane test facility… (more)

Cramer, Klaron Nathanael

2009-01-01T23:59:59.000Z

78

Technical and economic evaluation of selected compact drill rigs for drilling 10,000 foot geothermal production wells  

DOE Green Energy (OSTI)

This report summarizes the investigation and evaluation of several {open_quotes}compact{close_quotes} drill rigs which could be used for drilling geothermal production wells. Use of these smaller rigs would save money by reducing mobilization costs, fuel consumption, crew sizes, and environmental impact. Advantages and disadvantages of currently-manufactured rigs are identified, and desirable characteristics for the {open_quotes}ideal{close_quotes} compact rig are defined. The report includes a detailed cost estimate of a specific rig, and an evaluation of the cost/benefit ratio of using this rig. Industry contacts for further information are given.

Huttrer, G.W. [Geothermal Management Company, Inc., Frisco, CO (United States)

1997-11-01T23:59:59.000Z

79

,,,,,"Rig: TOI Discoverer Enterprise"  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Well: OCS-G 32306 002 ST00BP00",,,,"Flow Data" Well: OCS-G 32306 002 ST00BP00",,,,"Flow Data" ,,,,,"Field: Mississippi Canyon 252" ,,,,,"Rig: TOI Discoverer Enterprise" ,,,,,"Choke Manifold",,,,"Rates",,,,,,,,,"Ratio" "Date","Time","Choke A","Choke B","BSW","WHPres","WHTemp","WHDCP","WHDCTemp","Gas Rate","Gas Cum","Uncorrected ","Uncorrected ","Water Rate","Water Cum","Uncorrected ","Uncorrected ","Cumulative Oil ","GOR1","Comments" ,,,,,,,,,,,"Oil Rate","Oil Cum ",,,"Liquid Rate","Liquid Cum","from Cargo "

80

Slant rigs offer big payoffs in shallow drilling  

Science Conference Proceedings (OSTI)

Slant hole drilling technology can result in considerable savings over conventionally drilled deviated holes because mud motors and deviation control with measurement while drilling tools are usually unnecessary. The benefits of using slant hole rigs for development drilling improve after the bit walk tendencies and the correct bottom hole assemblies have been determined for a particular area. This article discusses three recent drilling operations that successfully used slant drilling technology on land-based projects: drilling for heavy oil in Alberta, drilling for gas in Alberta, and drilling a river crossing for a gas pipeline in British Columbia. These examples demonstrate the flexibility of slant drilling technology.

Smith, J. (George E. Failing Co., Enid, OK (US)); Edwards, B. (Sierra Drilling Co., Calgary (CA))

1992-03-30T23:59:59.000Z

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

A Testing and Controlling System for the Combustion Test Rig of Gas Turbine Combustor  

Science Conference Proceedings (OSTI)

In this paper, a testing and controlling system is designed for the test rig of gas turbine combustor by using VXi bus and PLC technology. The system is composed of two subsystems: the data acquisition subsystem and the control subsystem. The data acquisition ... Keywords: combustion test rig, VXi bus, PLC control, Modbus agreement, data acquisition

Nihui Xie; Hua Song; Hongzhuan Qiu

2011-10-01T23:59:59.000Z

82

Affine crystal structure on rigged configurations of type $D_{n}^{(1)}$  

Science Conference Proceedings (OSTI)

Extending the work in Schilling (Int. Math. Res. Not. 2006:97376, 2006), we introduce the affine crystal action on rigged configurations which is isomorphic to the Kirillov---Reshetikhin crystal B r,s of type Keywords: Crystal bases, Quantum algebras, Rigged configurations

Masato Okado; Reiho Sakamoto; Anne Schilling

2013-05-01T23:59:59.000Z

83

The Application Research of AC Frequency Conversion Technique in Transmission Control System of Oil Rig  

Science Conference Proceedings (OSTI)

This paper mainly introduced the basic structure and work principle of transmission agent on electric drilling rig, meanwhile the frequency control and parallel operation of motors used in the transmission agent were analyzed and designed. Using parallel ... Keywords: Rig, Transmission, Frequency control, Parallel Operation Control

Ruifan Yang; Yong Peng

2010-03-01T23:59:59.000Z

84

Probabilistic structure matching for visual SLAM with a multi-camera rig  

Science Conference Proceedings (OSTI)

We propose to use a multi-camera rig for simultaneous localization and mapping (SLAM), providing flexibility in sensor placement on mobile robot platforms while exploiting the stronger localization constraints provided by omni-directional sensors. In ... Keywords: Localization, Mapping, Mobile robot, Multi-camera rig, Omni-directional, SFM

Michael Kaess; Frank Dellaert

2010-02-01T23:59:59.000Z

85

Use power factor correction to cut SCR rig fuel bills  

SciTech Connect

When drilling with SCR-powered drilling rigs, there are specific instances on every well when the kVA capacity of the AC generators prohibits efficient engine loading. It then becomes necessary to run another engine-generator set to provide sufficient kVA to power the load, even though the kW required by the load can be furnished by existing engine(s) on line. The practice of running one more engine than can be fully loaded causes all engines on line to run at a less efficient point on the brake specific fuel consumption curve (BSFC) and therefore costs more in terms of engine hours, fuel and maintenance costs. This article presents a study of the load represented by the mud pump and drawworks along with a graphical representation that shows the effect of these loads on the engine generator system both with and without a power factor correction device.

Logan, R.T.

1983-09-01T23:59:59.000Z

86

HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office Facility  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office Facility Representative Division HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office Facility Representative Division : To determine that hoisting and rigging operations are conducted according to "industry best standards" for increasing equipment reliability while assuring worker safety, and to verify issues being addressed in BN Hoisting assessment. Criteria: Lifts are identified and categorized appropriately for scheduled maintenance. DOE-STD-1090-2001 An integrated process ensures safety issues are identified and controls established. DOE-STD-1090-2001 Personnel operating and maintaining the hoisting equipment are trained; they understand their roles and responsibilities. DOE-STD-1090-2001

87

Nucleotide sequences and modifications that determine RIG-I/RNA binding and signaling activities  

E-Print Network (OSTI)

Cytoplasmic viral RNAs with 5? triphosphates (5?ppp) are detected by the RNA helicase RIG-I, initiating downstream signaling and alpha/beta interferon (IFN-?/?) expression that establish an antiviral state. We demonstrate ...

Urzi, Dina

88

Calibration and performance of a selective catalytic reduction (SCR) bench rig for NOx? emissions control  

E-Print Network (OSTI)

A laboratory test rig was designed and built to easily test SCR (Selective Catalytic Reduction) technology. Equipped with three 6 kW heaters, connections for liquid N2 and an assortment of test gases, and a connection with ...

Castro Galnares, Sebastián (Castro Galnares Wright Paz)

2008-01-01T23:59:59.000Z

89

U.S. Crude Oil and Natural Gas Active Well Service Rigs in ...  

U.S. Energy Information Administration (EIA)

U.S. Crude Oil and Natural Gas Active Well Service Rigs in operation (Number of Elements) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9;

90

Structural basis of RNA recognition and activation by innate immune receptor RIG-I  

Science Conference Proceedings (OSTI)

Retinoic-acid-inducible gene-I (RIG-I; also known as DDX58) is a cytoplasmic pathogen recognition receptor that recognizes pathogen-associated molecular pattern (PAMP) motifs to differentiate between viral and cellular RNAs. RIG-I is activated by blunt-ended double-stranded (ds)RNA with or without a 5'-triphosphate (ppp), by single-stranded RNA marked by a 5'-ppp and by polyuridine sequences. Upon binding to such PAMP motifs, RIG-I initiates a signalling cascade that induces innate immune defences and inflammatory cytokines to establish an antiviral state. The RIG-I pathway is highly regulated and aberrant signalling leads to apoptosis, altered cell differentiation, inflammation, autoimmune diseases and cancer. The helicase and repressor domains (RD) of RIG-I recognize dsRNA and 5'-ppp RNA to activate the two amino-terminal caspase recruitment domains (CARDs) for signalling. Here, to understand the synergy between the helicase and the RD for RNA binding, and the contribution of ATP hydrolysis to RIG-I activation, we determined the structure of human RIG-I helicase-RD in complex with dsRNA and an ATP analogue. The helicase-RD organizes into a ring around dsRNA, capping one end, while contacting both strands using previously uncharacterized motifs to recognize dsRNA. Small-angle X-ray scattering, limited proteolysis and differential scanning fluorimetry indicate that RIG-I is in an extended and flexible conformation that compacts upon binding RNA. These results provide a detailed view of the role of helicase in dsRNA recognition, the synergy between the RD and the helicase for RNA binding and the organization of full-length RIG-I bound to dsRNA, and provide evidence of a conformational change upon RNA binding. The RIG-I helicase-RD structure is consistent with dsRNA translocation without unwinding and cooperative binding to RNA. The structure yields unprecedented insight into innate immunity and has a broader impact on other areas of biology, including RNA interference and DNA repair, which utilize homologous helicase domains within DICER and FANCM.

Jiang, Fuguo; Ramanathan, Anand; Miller, Matthew T.; Tang, Guo-Qing; Gale, Jr., Michael; Patel, Smita S.; Marcotrigiano, Joseph (Rutgers); (RWJ-Med); (UW-MED)

2012-05-29T23:59:59.000Z

91

Rigged Hilbert space formalism as an extended mathematical formalism for quantum systems. II. Transformation theory in nonrelativistic quantum mechanics  

Science Conference Proceedings (OSTI)

Results of a previous paper are used to obtain a rigorous mathematical formulation of the transformation theory of nonrelativistic quantum mechanics within the framework of rigged Hilbert spaces.

O. Melsheimer

1974-01-01T23:59:59.000Z

92

Test rig and particulate deposit and cleaning evaluation processes using the same  

DOE Patents (OSTI)

A rig and test program for determining the amount, if any, of contamination that will collect in the passages of a fluid flow system, such as a power plant fluid delivery system to equipment assemblies or sub-assemblies, and for establishing methods and processes for removing contamination therefrom. In the presently proposed embodiment, the rig and test programs are adapted in particular to utilize a high-pressure, high-volume water flush to remove contamination from substantially the entire fluid delivery system, both the quantity of contamination and as disposed or deposited within the system.

Schroder, Mark Stewart (Hendersonville, NC); Woodmansee, Donald Ernest (Schenectady, NY); Beadie, Douglas Frank (Greer, SC)

2002-01-01T23:59:59.000Z

93

Typical fault mode determination for rotor test rig based on correlation dimension and Kolmogorov entropy  

Science Conference Proceedings (OSTI)

This paper experimentally investigates the vibration faults of rotor, such as the unbalance, the loosening and the friction, using the rotor test rig. According to the theory of fractal and chaos, the vibration signal series are reconstructed. By the ... Keywords: Kolmogorov entropy, correlation dimension, fractal and chaos, vibration fault

Fengling Zhang; Yanting Ai; Fei Liu

2009-08-01T23:59:59.000Z

94

A Built for Purpose Micro-Hole Coiled Tubing Rig (MCTR)  

Science Conference Proceedings (OSTI)

This report will serve as the final report on the work performed from the contract period October 2005 thru April 2007. The project 'A Built for Purpose Microhole Coiled Tubing Rig (MCTR)' purpose was to upgrade an existing state-of-the-art Coiled Tubing Drilling Rig to a Microhole Coiled Tubing Rig (MCTR) capable of meeting the specifications and tasks of the Department of Energy. The individual tasks outlined to meet the Department of Energy's specifications are: (1) Concept and development of lubricator and tool deployment system; (2) Concept and development of process control and data acquisition; (3) Concept and development of safety and efficiency improvements; and (4) Final unit integration and testing. The end result of the MCTR upgrade has produced a unit capable of meeting the following requirements: (1) Capable of handling 1-inch through 2-3/8-inch coiled tubing (Currently dressed for 2-3/8-inch coiled tubing and capable of running up to 3-1/2-inch coiled tubing); (2) Capable of drilling and casing surface, intermediate, production and liner hole intervals; (3) Capable of drilling with coiled tubing and has all controls and installation piping for a top drive; (4) Rig is capable of running 7-5/8-inch range 2 casing; and (5) Capable of drilling 5,000 ft true vertical depth (TVD) and 6,000 ft true measured depth (TMD).

Bart Patton

2007-09-30T23:59:59.000Z

95

Use of fan rig data for the understanding and prediction of fan broadband noise and noise changes due to a variable area nozzle.  

E-Print Network (OSTI)

??This thesis presents the results of the research component of this EngD, entitled Use of fan rig data for the understanding and prediction of fan… (more)

Deane, Eugene Pio

2009-01-01T23:59:59.000Z

96

Passenger vehicle tire rolling resistance can be predicted from a flat-belt test rig  

Science Conference Proceedings (OSTI)

The rolling resistance of fifteen different types of tire was determined on-road by coastdown tests, using several vehicles variously fitted with 14 and 15 inch wheels. Corrections for tire pressure, and for external temperature, were deduced by data regression. The rolling resistance of the same tires was measured on a flat-belt tire test machine, and correction for tire pressure was determined in a like manner. In this paper, the results, in terms of the characteristic rolling resistance, are compared between rig and road. The various test procedures are discussed.

Ivens, J.

1989-01-01T23:59:59.000Z

97

Continuous injection of an inert gas through a drill rig for drilling into potentially hazardous areas  

DOE Patents (OSTI)

A drill rig for drilling in potentially hazardous areas includes a drill having conventional features such as a frame, a gear motor, gear box, and a drive. A hollow rotating shaft projects through the drive and frame. An auger, connected to the shaft is provided with a multiplicity of holes. An inert gas is supplied to the hollow shaft and directed from the rotating shaft to the holes in the auger. The inert gas flows down the hollow shaft, and then down the hollow auger, and out through the holes in the bottom of the auger into the potentially hazardous area.

McCormick, S.H.; Pigott, W.R.

1998-04-01T23:59:59.000Z

98

Advanced coal-fueled industrial cogeneration gas turbine system: Hot End Simulation Rig  

DOE Green Energy (OSTI)

This Hot End Simulation Rig (HESR) was an integral part of the overall Solar/METC program chartered to prove the technical, economic, an environmental feasibility of a coal-fueled gas turbine, for cogeneration applications. The program was to culminate in a test of a Solar Centaur Type H engine system operated on coal slurry fuel throughput the engine design operating range. This particular activity was designed to verify the performance of the Centaur Type H engine hot section materials in a coal-fired environment varying the amounts of alkali, ash, and sulfur in the coal to assess the material corrosion. Success in the program was dependent upon the satisfactory resolution of several key issues. Included was the control of hot end corrosion and erosion, necessary to ensure adequate operating life. The Hot End Simulation Rig addressed this important issue by exposing currently used hot section turbine alloys, alternate alloys, and commercially available advanced protective coating systems to a representative coal-fueled environment at turbine inlet temperatures typical of Solar`s Centaur Type H. Turbine hot end components which would experience material degradation include the transition duct from the combustor outlet to the turbine inlet, the shroud, nozzles, and blades. A ceramic candle filter vessel was included in the system as the particulate removal device for the HESR. In addition to turbine material testing, the candle material was exposed and evaluated. Long-term testing was intended to sufficiently characterize the performance of these materials for the turbine.

Galica, M.A.

1994-02-01T23:59:59.000Z

99

Specific features in building hardware-software complexes operating in real-time: An example of test rig used in periodic tests of reducers  

Science Conference Proceedings (OSTI)

Test rig for periodic tests of reducers is involved as an example to discuss specific features in building automatic test systems (ATS); the test rig is designed at ZAO NPP MIKS Engineering. A certain approach to ATS design based on adaptation of universal ...

A. A. Urakov; M. A. Rylov; D. S. Shutov; P. G. Dorofeev

2011-05-01T23:59:59.000Z

100

The Feasibility of Natural Gas as a Fuel Source for Modern Land-Based Drilling Rigs  

E-Print Network (OSTI)

The purpose of this study is to determine the feasibility of replacing diesel with natural gas as a fuel source for modern drilling rigs. More specifically, this thesis (1) establishes a control baseline by examining operational characteristics (response, fuel usage, and cost) of an existing diesel-powered land rig during the drilling of a well in the Haynesville Shale; (2) estimates operational characteristics of a natural gas engine under identical conditions; and (3) draws a comparison between diesel and natural gas engines, determining the advantages and disadvantages of those fuel sources in drilling applications. Results suggest that diesel engines respond to transient loads very effectively because of their inherently higher torque, especially when compared with natural gas engines of a similar power rating. Regarding fuel consumption, the engines running on diesel for this study were more efficient than on natural gas. On a per-Btu basis, the natural gas engines consumed nearly twice as much energy in drilling the same well. However, because of the low price of natural gas, the total cost of fuel to drill the well was lowered by approximately 54%, or 37,000 USD. Based on the results, it is possible to infer that the use of natural gas engines in drilling environments is feasible, and in most cases, an economical and environmental advantage. First, when compared with diesel, natural gas is a cleaner fuel with less negative impact on the environment. Second, fuel cost can be reduced by approximately half with a natural gas engine. On the other hand, natural gas as a fuel becomes less practical because of challenges associated with transporting and storing a gas. In fact, this difficulty is the main obstacle for the use of natural gas in drilling environments. In conclusion, because of its minimal drawback on operations, it is recommended that in situations where natural gas is readily available near current market prices, natural gas engines should be utilized because of the cost savings and reduced environmental impact. In all other cases, particularly where transport and storage costs encroach on the cost benefit, it may still be advantageous to continue powering rigs with diesel because of its ease of use.

Nunn, Andrew Howard

2011-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

ALTERNATE POWER AND ENERGY STORAGE/REUSE FOR DRILLING RIGS: REDUCED COST AND LOWER EMISSIONS PROVIDE LOWER FOOTPRINT FOR DRILLING OPERATIONS  

E-Print Network (OSTI)

Diesel engines operating the rig pose the problems of low efficiency and large amount of emissions. In addition the rig power requirements vary a lot with time and ongoing operation. Therefore it is in the best interest of operators to research on alternate drilling energy sources which can make entire drilling process economic and environmentally friendly. One of the major ways to reduce the footprint of drilling operations is to provide more efficient power sources for drilling operations. There are various sources of alternate energy storage/reuse. A quantitative comparison of physical size and economics shows that rigs powered by the electrical grid can provide lower cost operations, emit fewer emissions, are quieter, and have a smaller surface footprint than conventional diesel powered drilling. This thesis describes a study to evaluate the feasibility of adopting technology to reduce the size of the power generating equipment on drilling rigs and to provide ?peak shaving? energy through the new energy generating and energy storage devices such as flywheels. An energy audit was conducted on a new generation light weight Huisman LOC 250 rig drilling in South Texas to gather comprehensive time stamped drilling data. A study of emissions while drilling operation was also conducted during the audit. The data was analyzed using MATLAB and compared to a theoretical energy audit. The study showed that it is possible to remove peaks of rig power requirement by a flywheel kinetic energy recovery and storage (KERS) system and that linking to the electrical grid would supply sufficient power to operate the rig normally. Both the link to the grid and the KERS system would fit within a standard ISO container. A cost benefit analysis of the containerized system to transfer grid power to a rig, coupled with the KERS indicated that such a design had the potential to save more than $10,000 per week of drilling operations with significantly lower emissions, quieter operation, and smaller size well pad.

Verma, Ankit

2009-05-01T23:59:59.000Z

102

Design and Analysis of a Test Rig for Modeling the Bit/Formation Interface in Petroleum Drilling Applications  

E-Print Network (OSTI)

Equipment failure and well deviations are prevailing contributors to production delays within the petroleum industry. Particular monetary focus is given to the drilling operations of wells to overcome these deficits, in order to extract natural resources as efficiently, and as safely, as possible. The research presented here focuses on minimizing vibrations of the drill string near the bottom-hole assembly (BHA) by identifying the cause of external forcing on the drillstring in vertical and horizontal wells and measuring the effects of various factors on the stability of perturbations on the system. A test rig concept has been developed to accurately measure the interaction forces and torques between the bit, formation and fluids during drilling in order to clearly define a bit/formation interface law (BFIL) for the purpose vibrational analysis. As a secondary function, the rig will be able to measure the potential inputs to a drilling simulation code that can be used to model drillstring vibrations. All notable quantities will be measured including torque on bit (TOB), weight on bit (WOB), lateral impact loads (LIL), formation stiffness, bit specific properties, fluid damping coefficients and rate of penetration (ROP). The conceptual design has been analyzed and refined, in detail, to verify its operational integrity and range of measurement error. The operational envelope of the rig is such that a drill bit of up to 8 ½ inches in diameter can be effectively tested at desired operational parameters (WOB: 0-55,000 lbf, RPM: 60-200) with various rock formations and multiple fluid types. Future use and design possibilities are also discussed to enhance the functionality of the rig and the potential for further research in the area of oil and gas drilling and vibrational modeling.

Wilson, Joshua Kyle

2013-05-01T23:59:59.000Z

103

Loads on Tie-Down Systems for Floating Drilling Rigs during Hurricane Conditions  

E-Print Network (OSTI)

Tie-down systems are used to fasten drilling rigs to the deck of offshore structures during harsh environmental conditions such as hurricanes. During Hurricane Ivan (2004) and Katrina (2005), a number of offshore structures were moved and several tie-down systems were damaged. In the present study, the reaction force and connection capacity of tie-down systems for a TLP and SPAR are investigated. The environmental conditions are taken from the API Bulletin 2INT-MET which has been updated after several major storms during 2004-2005. The hydrodynamic coefficients of the TLP and SPAR are obtained using a 3D diffraction/radiation panel method. The motions of the TLP and SPAR are then simulated in the time domain by using the hull-mooring-riser coupled dynamic analysis tool CHARM3D. Based on the simulated motion and acceleration time series, the inertial and gravity loads on derrick and skid base footing are calculated. In addition to the inertial-gravity loads, wind forces exerted on the derrick are also calculated. All the external forces and resultant hull motions are simulated for 100-year, 200-year and 1000-year storms to observe the derrick structural integrity with increasing environmental intensity. Various environmental headings are also considered to find the maximum reaction forces. In the present method, the phase differences between gravity-inertia forces and wind forces are taken into consideration to obtain more realistic loads on derrick and skid base footings. This research shows that the maximum and minimum load values are appreciably higher for the SPAR. In addition, the direction of external forces is also important to determine maximum reaction forces on footings. The capacities of the clamps in slip, bolt tension, and bolt shear can be also analyzed using the resultant data to provide guidance on appropriate design values.

Bae, Yoon Hyeok

2009-05-01T23:59:59.000Z

104

Experimental evaluation of a metal-mesh bearing damper in a high speed test rig  

E-Print Network (OSTI)

Metal mesh is a commercially available material used in many applications including seals, heat shields, filters, gaskets, aircraft engine mounts, and vibration absorbers. This material has been tested in the Turbomachinery Laboratory at Texas A&M University (TAMU) as a bearing damper in a rotordynamic test rig. The test facility was originally used to support the design of a turboprop engine at TAMU, developing squirrel cage bearing supports and squeeze film dampers for both the gas generator and power turbine rotors. To design the metal mesh damper, static stiffness and dynamic rap test measurements were first made on metal mesh samples in a specially designed non-rotating test fixture. These property tests were performed on samples of various densities and press fits. One sample was also tested in an Instron machine as an ancillary and redundant way to determine the stiffness. Using the stiffness test results and equations derived by a previous investigator, a spreadsheet program was written and used to size metal mesh donuts that have the radial stiffness value required to replace the squirrel cage in the power turbine. The squirrel cage and squeeze-film bearing damper developed for the power turbine rotor was then replaced by a metal mesh donut sized by the computer code. Coast-down tests were conducted through the first critical speed of the power turbine. The results of the metal mesh tests were compared with those obtained from previous testing with the squeeze film damper. The results show that the metal mesh damper has the same damping as the squeeze film at room temperature but does not lose its damping at elevated temperatures up to 210F?. Experiments were run under several different conditions including balanced rotor hot oil soaked, unbalanced rotor hot oil soaked, balanced dry, and unbalanced dry. Over all, metal mesh dampers appear to be a viable and attractive substitute for squeeze film dampers in gas turbine engines. The advantages shown to date include less variation of damping with temperature, ability to handle large rotor unbalance, and the ability (if required) to operate effectively in an oil free environment.

Zarzour, Mark Joseph

1999-01-01T23:59:59.000Z

105

Table 4.4 Crude Oil and Natural Gas Rotary Rigs in ...  

U.S. Energy Information Administration (EIA)

1954. na: na: na: na: 2,508: 1955. na: na: na: na: 2,686: 1956. na: na: na: na: 2,620: 1957. na: na: na: na: 2,426: 1958. na: na: na: na: 1,922: 1959. ...

106

U.S. Onshore Crude Oil and Natural Gas Rotary Rigs in ...  

U.S. Energy Information Administration (EIA)

1,954: 1,979: 2,016: 2,066: 2,103: 2,122: 2,127: 2,138: 2,156: 2,169: 2,098: 1979: 1,992: 1,858: 1,768: 1,736: 1,762: 1,794: 1,889: 2,014: 2,069: ...

107

www.myresources.com.au OIL & GAS BULLETIN VOL. 15, NO. 11 PAGE 9 Safety first: Oil rigs off the north west shelf will be studied for  

E-Print Network (OSTI)

www.myresources.com.au OIL & GAS BULLETIN VOL. 15, NO. 11 PAGE 9 NEWS Safety first: Oil rigs off for future successful tight gas exploration projects in Western Australia has been set up and studies the tight gas sand field at its exploration permit in the South Perth Basin. Professor Rezaee said

108

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 LIFTING PERSONNEL 4-i Chapter 4 Lifting Personnel This chapter specifies the design and inspection requirements for personnel lift platforms as well as the operational requirements for such platforms and appurtenant hoisting equipment. It implements the requirements of ASME B30.23, Personnel Lifting Systems (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 4.1 GENERAL ................................................................................................................................4-1 4.1.1 Personnel Lifting Evaluation .......................................................................................4-1 4.1.2 Designated Leader .......................................................................................................4-1

109

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Change Notice No. 1 DOE-STD-1090-2007 Change Notice No. 1 DOE-STD-1090-2007 December 2007 Chapter 4 Provide ASME attribution at introduction to the Table on Contents and on Figures 4-3,4 and Exhibits 1 & 2 Chapter 7 Provide ASME attribution at introduction to the Table on Contents and on Figures 7-1,2,3,4,5 and Table 7-1 Chapter 8 Provide ASME attribution at introduction to the Table on Contents and on Figures 8-1,2,3,4,5,6,7,8,9 and Table 8-1 Chapter 9 Provide ASME attribution at introduction to the Table on Contents and on Figures 9-1,2,3,4,5,6 and Table 9-2 Chapter 11 Provide ASME attribution at introduction to the Table on Contents and on Figures 11-10,15 and Tables 11-10,11,14,15,16 Chapter 12 Provide ASME attribution at introduction to the Table on Contents and on

110

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8 8 HOISTS 8-i This chapter provides safety standards for inspecting, testing, and operating hoists not permanently mounted on overhead cranes and implements the requirements of ASME B30.11 ("Monorail Systems and Underhung Cranes"), B30.16["Overhead Hoists (Underhung)"], and B30.21 ("Manually Lever Operated Hoists") (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 8.1 GENERAL .................................................................................................................................8-1 8.1.1 Operator Training/Qualification ..................................................................................8-4 8.1.2 Marking........................................................................................................................8-4

111

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7 7 OVERHEAD AND GANTRY CRANES 7-i This chapter specifies operation, inspection, maintenance, and testing requirements for the use of overhead and gantry cranes and implements the requirements of ASME B30.2 ["Overhead and Gantry Cranes (Top- Running Bridge, Single or Multiple Girder, Top-Running Trolley Hoist)"], B30.11 ("Monorail Systems and Underhung Cranes"), and B30.17 ["Overhead and Gantry Cranes (Top-Running Bridge, Single Girder, Underhung Hoist")] (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 7.1 GENERAL .................................................................................................................................7-1 7.1.1 Operator Training/Qualification

112

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CHAPTER 9 MOBILE CRANES 9-i This chapter specifies operation, inspection, maintenance, and testing requirements for the use of mobile cranes and implements the requirements of ASME B30.5 ("Mobile and Locomotive Cranes") (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 9.1 GENERAL .................................................................................................................................9-1 9.1.1 Operator Training/Qualification ..................................................................................9-1 9.1.2 Load Limits..................................................................................................................9-1 9.1.3 Load Rating Chart........................................................................................................9-1

113

rig upgrades2.qxp  

NLE Websites -- All DOE Office Websites (Extended Search)

D E T I N U S O F A M E R I C A E A s the oil and gas industry continues to drill in more remote areas, at deeper depths, and in more challenging environments, the advancement of...

114

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

A frames (sometimes referred to as portable gantries), Truck mounted cranes with a capacity of 1 ton or less not covered in ASME B30.5 (.Mobile and Locomotive Cranes.) and self...

115

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Four-pad pow ered vacuum lifting device Four-pad pow ered vacuum lifting device manipulator DOE-STD-1090-2007 14.3 VACUUM LIFTING DEVICES 14-11 Chapter 14 Below-the-Hook...

116

Build a Floating Oil Rig  

Energy.gov (U.S. Department of Energy (DOE))

The U.S. Department of the Interior's Minerals Management Service developed this teacher's guide about the many energy resources found in, over, and under the ocean. Includes sections on petroleum,...

117

Well servicing rig market report  

Science Conference Proceedings (OSTI)

This article profiles the well servicing industry, focusing on the problems facing the industry under currently depressed market conditions. The problems of rising operating costs, oil price uncertainty, and aging equipment are addressed specifically.

Killalea, M

1989-01-01T23:59:59.000Z

118

High-Temperature-Turbine Technology Program: Phase II. Technology test and support studies. Design and development of the liquid-fueled high-temperature combustor for the Turbine Spool Technology Rig  

SciTech Connect

The concept selected by Curtiss-Wright for this DOE sponsored High Temperature Turbine Technology (HTTT) Program utilizes transpiration air-cooling of the turbine subsystem airfoils. With moderate quantities of cooling air, this method of cooling has been demonstrated to be effective in a 2600 to 3000/sup 0/F gas stream. Test results show that transpiration air-cooling also protects turbine components from the aggressive environment produced by the combustion of coal-derived fuels. A new single-stage, high work transpiration air-cooled turbine has been designed and fabricated for evaluation in a rotating test vehicle designated the Turbine Spool Technology Rig (TSTR). The design and development of the annular combustor for the TSTR are described. Some pertinent design characteristics of the combustor are: fuel, Jet A; inlet temperature, 525/sup 0/F; inlet pressure, 7.5 Atm; temperature rise, 2475/sup 0/F; efficiency, 98.5%; exit temperature pattern, 0.25; and exit mass flow, 92.7 pps. The development program was conducted on a 60/sup 0/ sector of the full-round annular combustor. Most design goals were achieved, with the exception of the peak gas exit temperature and local metal temperatures at the rear of the inner liner, both of which were higher than the design values. Subsequent turbine vane cascade testing established the need to reduce both the peak gas temperature (for optimum vane cooling) and the inner liner metal temperature (for combustor durability). Further development of the 60/sup 0/ combustor sector achieved the required temperature reductions and the final configuration was incorporated in the TSTR full-annular burner.

1981-06-01T23:59:59.000Z

119

Rigs Drilling Gas Wells Are At  

U.S. Energy Information Administration (EIA)

The increasing number of resulting gas well completions have been expanding production in major producing States, such as Texas. For the year 2000, ...

120

Drill Rig Safety Topics of the Presentation  

E-Print Network (OSTI)

· Check oil level daily -engine oil & coolant -compressor air/oil tank -hydraulic tank -pump oil (water injection, mud, etc.) -pump drive gearboxes · Grease daily (must purge dirt) ­ Floating Sub ­ Rollers ­ Air · Fuel and Oil Leaks · Hose Leaks and Failures · Electrical · Smoking #12;Schramm Electrical Safety

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Comparative analysis of core drilling and rotary drilling in volcanic terrane  

DOE Green Energy (OSTI)

Initially, the goal of this report is to compare and contrast penetration rates of rotary-mud drilling and core drilling in young volcanic terranes. It is widely recognized that areas containing an abundance of recent volcanic rocks are excellent targets for geothermal resources. Exploration programs depend heavily upon reliable subsurface information, because surface geophysical methods may be ineffective, inconclusive, or both. Past exploration drilling programs have mainly relied upon rotary-mud rigs for virtually all drilling activity. Core-drilling became popular several years ago, because it could deal effectively with two major problems encountered in young volcanic terranes: very hard, abrasive rock and extreme difficulty in controlling loss of circulation. In addition to overcoming these difficulties, core-drilling produced subsurface samples (core) that defined lithostratigraphy, structure and fractures far better than drill-chips. It seemed that the only negative aspect of core drilling was cost. The cost-per-foot may be two to three times higher than an ''initial quote'' for rotary drilling. In addition, penetration rates for comparable rock-types are often much lower for coring operations. This report also seeks to identify the extent of wireline core drilling (core-drilling using wireline retrieval) as a geothermal exploration tool. 25 refs., 21 figs., 13 tabs.

Flynn, T.; Trexler, D.T.; Wallace, R.H. Jr. (ed.)

1987-04-01T23:59:59.000Z

122

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 PREENGINEERED PRODUCTION LIFTS 3-i Chapter 3 Preengineered Production Lifts This chapter provides requirements for the design, evaluation, and performance of preengineered production lifts. This lift designation may be used at the discretion of the contractor for selected operations. 3.1 PREENGINEERED PRODUCTION LIFT DETERMINATION.......................................3-1 3.2 LIFTING FIXTURES..............................................................................................................3-2 3.2.1 Design ..........................................................................................................................3-2 3.2.2 Fabrication ...................................................................................................................3-2

123

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2 2 CRITICAL LIFTS 2-i Chapter 2 Critical Lifts This chapter provides guidelines for critical-lift determination and requirements for planning and performing a critical lift safely and judiciously. 2.1 CRITICAL-LIFT DETERMINATION ................................................................ 2-1 2.2 CRITICAL-LIFT REQUIREMENTS ............................................................. 2-2 DOE-STD-1090-2007 Chapter 2 2-ii Critical Lifts INTENTIONALLY BLANK DOE-STD-1090-2007 2.1 CRITICAL-LIFT DETERMINATION 2-1 Chapter 2 Critical Lifts a. An appointed person shall classify each lift into one of the DOE categories (ordinary, critical, or preengineered production) prior to planning the lift. b. A lift shall be designated critical if any of

124

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2 2 CRITICAL LIFTS 2-i Chapter 2 Critical Lifts This chapter provides guidelines for critical-lift determination and requirements for planning and performing a critical lift safely and judiciously. 2.1 CRITICAL-LIFT DETERMINATION ................................................................ 2-1 2.2 CRITICAL-LIFT REQUIREMENTS ............................................................. 2-2 DOE-STD-1090-2004 Chapter 2 2-ii Critical Lifts INTENTIONALLY BLANK DOE-STD-1090-2004 2.1 CRITICAL-LIFT DETERMINATION 2-1 Chapter 2 Critical Lifts a. An appointed person shall classify each lift into one of the DOE categories (ordinary, critical, or preengineered production) prior to planning the lift. b. A lift shall be designated critical if any of

125

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 LIFTING PERSONNEL 4-i Chapter 4 Lifting Personnel This chapter describes requirements for lifting personnel. 4.1 GENERAL................................................................................................................................4-1 4.1.1 Personnel Lifting Evaluation .......................................................................................4-1 4.1.2 Designated Leader .......................................................................................................4-1 4.1.3 Trial Lift.......................................................................................................................4-2 4.1.4 Lifting Operations........................................................................................................4-2

126

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CHAPTER 17 CHAPTER 17 REFERENCES 17-1 Chapter 17 References American Institute of Steel Construction AISC Specifications for the design, fabrication, and erection of structural steel for buildings. American Iron and Steel Institute AISI Standards for Type-302 or Type-304 stainless steel. American National Standards Institute and American Society of Mechanical Engineers ANSI A10.28, Work Platforms Suspended From Cranes or Derricks. ANSI A10.18, Floor and Wall Openings, Railings and Toe Boards. ASME B30.2, Overhead and Gantry Cranes (Top-Running Bridge, Single or Multiple Girder, Top-Running Trolley Hoist). ASME B30.5, Mobile and Locomotive Cranes. ASME B30.6, Derricks. ASME B30.7, Base-Mounted Drum Hoists. ASME B30.9, Slings. ASME B30.10, Hooks.

127

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8 8 HOISTS 8-i Chapter 8 Hoists This chapter provides safety standards for inspecting, testing, and operating hoists not permanently mounted on overhead cranes and implements the requirements of ASME B30.11 ("Monorail Systems and Underhung Cranes"), B30.16["Overhead Hoists (Underhung)"], and B30.21 ("Manually Lever Operated Hoists"). 8.1 GENERAL .................................................................................................................................8-1 8.1.1 Operator Training/Qualification ..................................................................................8-4 8.1.2 Marking........................................................................................................................8-4

128

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6 6 PERSONNEL QUALIFICATION AND TRAINING 6-i Chapter 6 Personnel Qualification and Training This chapter describes personnel qualification and training. Only qualified personnel shall operate the equipment covered in this standard. 6.1 GENERAL ................................................................................................................................6-1 6.2 QUALIFICATION...................................................................................................................6-2 6.2.1 General.........................................................................................................................6-2 6.2.2 Operators of Cab-Operated and Pulpit-Operated Cranes .............................................6-2

129

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0 0 FORKLIFT TRUCKS 10-i Chapter 10 Forklift Trucks This chapter specifies operation, inspection, testing, and maintenance requirements for forklift trucks powered by internal-combustion engines or electric motors and implements the requirements of ASME B56.1 ("Safety Standard for powered Industrial Trucks - Low Lift and High lift Trucks") and B56.6 ("Rough Terrain Fork Lift Trucks"), and ANSI/UL 558 ("Internal-Combustion-Engine-Powered Industrial Trucks") and 583 ("Electric-Battery-Powered Industrial Trucks"). 10.1 GENERAL ...............................................................................................................................10-1 10.1.1 Operator Training/Qualification ................................................................................10-1

130

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

019-2004 019-2004 CHAPTER 16 MISCELLANEOUS LIFTING DEVICES 16-i Chapter 16 Miscellaneous Lifting Devices This chapter provides safety standards designated to sign verify, based on personal observations, certified records, or direct reports, that a specific action has been performed in accordance with specified requirements. For the operation, inspection, testing, and maintenance for miscellaneous lifting devices, (truck mounted cranes - capacity 1 ton or less not covered in ASME B30.5 ("Mobile and Locomotive Cranes") and implements the requirements of ASME PALD ("Portable Automotive Lifting Devices") for self contained shop cranes. 16.1 GENERAL ..................................................................................................................................

131

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7 7 OVERHEAD AND GANTRY CRANES 7-i Chapter 7 Overhead and Gantry Cranes This chapter specifies operation, inspection, maintenance, and testing requirements for the use of overhead and gantry cranes and implements the requirements of ASME B30.2 ["Overhead and Gantry Cranes (Top- Running Bridge, Single or Multiple Girder, Top-Running Trolley Hoist)"], B30.11 ("Monorail Systems and Underhung Cranes"), and B30.17 ["Overhead and Gantry Cranes (Top-Running Bridge, Single Girder, Underhung Hoist")]. Only equipment built to the appropriate design standards shall be used in DOE installations. 7.1 GENERAL .................................................................................................................................7-1

132

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6 6 PERSONNEL QUALIFICATION AND TRAINING 6-i Chapter 6 Personnel Qualification and Training This chapter describes personnel qualification and training. Only qualified personnel shall operate the equipment covered in this standard. 6.1 GENERAL................................................................................................................................6-1 6.2 QUALIFICATION...................................................................................................................6-2 6.2.1 General.........................................................................................................................6-2 6.2.2 Operators of Cap-Operated and Pulpit-Operated Cranes .............................................6-2

133

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DEFINITIONS DEFINITIONS ................................................. 1-1 CHAPTER 2 CRITICAL LIFTS................................................................................. 2-1 2.1 CRITICAL-LIFT DETERMINATION........................................................ 2-1 2.2 CRITIAL-LIFT REQUIREMENTS............................................................. 2-2 CHAPTER 3 PREENGINEERED PRODUCTION LIFTS................................3-1 3.1 GENERAL....................................................................................................... 3-1 3.2 OPERATION EVALUATION ...................................................................... 3-2 3.2.1 Load Identification................................................................................

134

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0 0 FORKLIFT TRUCKS 10-i This chapter specifies operation, inspection, testing, and maintenance requirements for forklift trucks powered by internal-combustion engines or electric motors and implements the requirements of ANSI/ITSDF B56.1 ("Safety Standard for powered Industrial Trucks - Low Lift and High lift Trucks") and ANSI/ITSDF B56.6 ("Rough Terrain Fork Lift Trucks"), and ANSI/UL 558 ("Internal-Combustion- Engine-Powered Industrial Trucks") and ANSI/UL 583 ("Electric-Battery-Powered Industrial Trucks"). 10.1 GENERAL ...............................................................................................................................10-1 10.1.1 Operator Training/Qualification ................................................................................10-1

135

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 PREENGINEERED PRODUCTION LIFTS 3-i Chapter 3 Preengineered Production Lifts This chapter provides requirements for the design, evaluation, and performance of preengineered production lifts. This lift designation may be used at the discretion of the contractor for selected operations. 3.1 GENERAL................................................................................................................................3-1 3.2 OPERATION EVALUATION................................................................................................3-2 3.2.1 Load Identification.......................................................................................................3-2 3.2.2 Task Determination......................................................................................................3-2

136

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7 7 REFERENCES 17-1 Chapter 17 References American Institute of Steel Construction AISC Specifications for the design, fabrication, and erection of structural steel for buildings. American Iron and Steel Institute AISI Standards for Type-302 or Type-304 stainless steel. American National Standards Institute and the American Society of Mechanical Engineers ANSI A10.28, Work Platforms Suspended From Cranes or Derricks. ANSI A10.18, Floor and Wall Openings, Railings and Toe Boards. ASME B30.1, Jacks ASME B30.2, Overhead and Gantry Cranes (Top-Running Bridge, Single or Multiple Girder, Top-Running Trolley Hoist). ASME B30.5, Mobile and Locomotive Cranes. ASME B30.6, Derricks. ASME B30.7, Base-Mounted Drum Hoists. ASME B30.9, Slings.

137

U.S. oil rig count overtakes natural gas rig count - Today in ...  

U.S. Energy Information Administration (EIA)

Petroleum & Other Liquids. Crude oil, gasoline, heating oil, diesel, propane, and other liquids including biofuels and natural gas liquids. Natural Gas

138

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DEFINITIONS........................................1-1 DEFINITIONS........................................1-1 CHAPTER 2 CRITICAL LIFTS .......................................................................2-1 2.1 CRITICAL-LIFT DETERMINATION........................................................ 2-1 2.2 CRITIAL-LIFT REQUIREMENTS............................................................. 2-2 CHAPTER 3 PREENGINEERED PRODUCTION LIFTS................................3-1 3.1 PRENGINEERED PRODUCTION LIFT DETERMINATION................ 3-1 3.2 LIFTING FIXTURES .................................................................................... 3-2 3.3.1 Design ................................................................................................... 3-2 3.3.2 Fabrication ............................................................................................

139

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9 9 MOBILE CRANES 9-i Chapter 9 Mobile Cranes This chapter specifies operation, inspection, maintenance, and testing requirements for the use of mobile cranes and implements the requirements of ASME B30.5 ("Mobile and Locomotive Cranes"). Only equipment built to appropriate design standards shall be used at DOE installations. 9.1 GENERAL .................................................................................................................................9-1 9.1.1 Operator Training/Qualification ..................................................................................9-1 9.1.2 Load Limits..................................................................................................................9-1 9.1.3 Load Rating Chart........................................................................................................9-1

140

Rethinking rig count as a predictor of natural gas production ...  

U.S. Energy Information Administration (EIA)

Uranium fuel, nuclear reactors, ... What is the role of coal in the United States? ... Using historical data ...

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Flow field survey in a transonic compressor rig .  

E-Print Network (OSTI)

??As the Navy prepares to transition to F-35C Joint Strike Fighter the need to understand "pop stalls – caused by steam leakage in catapult systems is… (more)

Rose, Christopher W.

2006-01-01T23:59:59.000Z

142

Pad drilling and rig mobility lead to more efficient drilling ...  

U.S. Energy Information Administration (EIA)

Biofuels: Ethanol & Biodiesel ... Pad drilling allows producers to target a significant area of underground resources while minimizing impact on the surface.

143

Basic Rigging Workbook Training and Qualifications Program Office  

E-Print Network (OSTI)

................................................................................................................... 42 Carbon Steel Pipe Size Chart. This instructor handbook incorporates the Subject Area's requirements, as well as information from the Department

Homes, Christopher C.

144

Rigs Drilling Gas Wells Are At - Energy Information Administration  

U.S. Energy Information Administration (EIA)

The increasing number of resulting gas well completions have been expanding production in major producing States, such as Texas. For the year 2000, ...

145

Pad drilling and rig mobility lead to more efficient drilling ...  

U.S. Energy Information Administration (EIA)

Tools; Glossary › All Reports ... weather; gasoline; capacity; nuclear; exports; forecast; View All Tags ...

146

Rethinking rig count as a predictor of natural gas ...  

U.S. Energy Information Administration (EIA)

Includes hydropower, solar, wind, geothermal, biomass and ethanol. Nuclear & Uranium. Uranium fuel, nuclear reactors, generation, spent fuel. ... ...

147

Rotary drive mechanism  

Science Conference Proceedings (OSTI)

This patent describes a rotary drive mechanism which includes a rotary solenoid having a stator and multi-poled rotor. A moving member rotates with the rotor and is biased by a biasing device. The biasing device causes a further rotational movement after rotation by the rotary solenoid. Thus, energization of the rotary solenoid moves the member in one direction to one position and biases the biasing device against the member. Subsequently, de- energization of the rotary solenoid causes the biasing device to move the member in the same direction to another position from where the moving member is again movable by energization and de-energization of the rotary solenoid. Preferably, the moving member is a multi-lobed cam having the same number of lobes as the rotor has poles. An anti- overdrive device is also preferably provided for preventing overdrive in the forward direction or a reverse rotation of the moving member and for precisely aligning the moving member.

Kenderdine, E.W.

1991-10-08T23:59:59.000Z

148

Rotary drive mechanism  

Science Conference Proceedings (OSTI)

A rotary drive mechanism includes a rotary solenoid having a stator and multi-poled rotor. A moving member rotates with the rotor and is biased by a biasing device. The biasing device causes a further rotational movement after rotation by the rotary solenoid. Thus, energization of the rotary solenoid moves the member in one direction to one position and biases the biasing device against the member. Subsequently, de-energization of the rotary solenoid causes the biasing device to move the member in the same direction to another position from where the moving member is again movable by energization and de-energization of the rotary solenoid. Preferably, the moving member is a multi-lobed cam having the same number of lobes as the rotor has poles. An anti-overdrive device is also preferably provided for preventing overdrive in the forward direction or a reverse rotation of the moving member and for precisely aligning the moving member.

Kenderdine, Eugene W. (Albuquerque, NM)

1991-01-01T23:59:59.000Z

149

EM Rotary Filter Program  

Electrical Junction Box Motors for Rotary Microfilters Motor Operated Valves Electrical ... savings SMPs Clarified Salt Solution Pumping System Sr-90 and actinides

150

U.S. Crude Oil, Natural Gas, and Natural Gas Liquids Reserves 2006 ...  

U.S. Energy Information Administration (EIA)

... and the Average Number of Active Rotary Drilling Rigs, 1977-2006: PDF: 4: ... Glossary: A listing of terms used within the Reserves Report, and their ...

151

U.S. Crude Oil, Natural Gas, and Natural Gas Liquids Reserves 2005 ...  

U.S. Energy Information Administration (EIA)

... and the Average Number of Active Rotary Drilling Rigs, 1977-2005: PDF: 4: ... Glossary: A listing of terms used within the Reserves Report, and their ...

152

Crude Oil and Natural Gas Drilling Activity  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Rotary rigs in operation ...

153

Crude Oil and Natural Gas Drilling Activity  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Rotary rigs in ...

154

Rotary mechanical latch  

Science Conference Proceedings (OSTI)

A rotary mechanical latch for positive latching and unlatching of a rotary device with a latchable rotating assembly having a latching gear that can be driven to latched and unlatched states by a drive mechanism such as an electric motor. A cam arm affixed to the latching gear interfaces with leading and trailing latch cams affixed to a flange within the drive mechanism. The interaction of the cam arm with leading and trailing latch cams prevents rotation of the rotating assembly by external forces such as those due to vibration or tampering.

Spletzer, Barry L.; Martinez, Michael A.; Marron, Lisa C.

2012-11-13T23:59:59.000Z

155

Solar heated rotary kiln  

SciTech Connect

A solar heated rotary kiln utilized for decomposition of materials, such as zinc sulfate. The rotary kiln has an open end and is enclosed in a sealed container having a window positioned for directing solar energy into the open end of the kiln. The material to be decomposed is directed through the container into the kiln by a feed tube. The container is also provided with an outlet for exhaust gases and an outlet for spent solids, and rests on a tiltable base. The window may be cooled and kept clear of debris by coolant gases.

Shell, Pamela K. (Tracy, CA)

1984-01-01T23:59:59.000Z

156

Rotary shaft sealing assembly  

DOE Patents (OSTI)

A rotary shaft sealing assembly in which a first fluid is partitioned from a second fluid in a housing assembly having a rotary shaft located at least partially within. In one embodiment a lip seal is lubricated and flushed with a pressure-generating seal ring preferably having an angled diverting feature. The pressure-generating seal ring and a hydrodynamic seal may be used to define a lubricant-filled region with each of the seals having hydrodynamic inlets facing the lubricant-filled region. Another aspect of the sealing assembly is having a seal to contain pressurized lubricant while withstanding high rotary speeds. Another rotary shaft sealing assembly embodiment includes a lubricant supply providing a lubricant at an elevated pressure to a region between a lip seal and a hydrodynamic seal with a flow control regulating the flow of lubricant past the lip seal. The hydrodynamic seal may include an energizer element having a modulus of elasticity greater than the modulus of elasticity of a sealing lip of the hydrodynamic seal.

Dietle, Lannie L. (Houston, TX); Schroeder, John E. (Richmond, TX); Kalsi, Manmohan S. (Houston, TX); Alvarez, Patricio D. (Richmond, TX)

2010-09-21T23:59:59.000Z

157

Rotary shaft sealing assembly  

DOE Patents (OSTI)

A rotary shaft sealing assembly in which a first fluid is partitioned from a second fluid in a housing assembly having a rotary shaft located at least partially within. In one embodiment a lip seal is lubricated and flushed with a pressure-generating seal ring preferably having an angled diverting feature. The pressure-generating seal ring and a hydrodynamic seal may be used to define a lubricant-filled region with each of the seals having hydrodynamic inlets facing the lubricant-filled region. Another aspect of the sealing assembly is having a seal to contain pressurized lubricant while withstanding high rotary speeds. Another rotary shaft sealing assembly embodiment includes a lubricant supply providing a lubricant at an elevated pressure to a region between a lip seal and a hydrodynamic seal with a flow control regulating the flow of lubricant past the lip seal. The hydrodynamic seal may include an energizer element having a modulus of elasticity greater than the modulus of elasticity of a sealing lip of the hydrodynamic seal.

Dietle, Lannie L; Schroeder, John E; Kalsi, Manmohan S; Alvarez, Patricio D

2013-08-13T23:59:59.000Z

158

Rotary magnetic heat pump  

DOE Patents (OSTI)

A rotary magnetic heat pump constructed without flow seals or segmented rotor accomplishes recuperation and regeneration by using split flow paths. Heat exchange fluid pumped through heat exchangers and returned to the heat pump splits into two flow components: one flowing counter to the rotor rotation and one flowing with the rotation.

Kirol, Lance D. (Shelly, ID)

1988-01-01T23:59:59.000Z

159

Rotary pneumatic valve  

DOE Patents (OSTI)

A rotary pneumatic valve which is thrust balanced and the pneumatic pressure developed produces only radial loads on the valve cylinder producing negligible resistance and thus minimal torque on the bearings of the valve. The valve is multiplexed such that at least two complete switching cycles occur for each revolution of the cylinder spindle. 4 figs.

Hardee, H.C.

1989-08-02T23:59:59.000Z

160

Rotary Burner Demonstration  

Science Conference Proceedings (OSTI)

The subject technology, the Calcpos Rotary Burner (CRB), is a burner that is proposed to reduce energy consumption and emission levels in comparison to currently available technology. burners are used throughout industry to produce the heat that is required during the refining process. Refineries seek to minimize the use of energy in refining while still meeting EPA regulations for emissions.

Paul Flanagan

2003-04-30T23:59:59.000Z

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Rotary magnetic heat pump  

DOE Patents (OSTI)

A rotary magnetic heat pump constructed without flow seals or segmented rotor accomplishes recuperation and regeneration by using split flow paths. Heat exchange fluid pumped through heat exchangers and returned to the heat pump splits into two flow components: one flowing counter to the rotor rotation and one flowing with the rotation. 5 figs.

Kirol, L.D.

1987-02-11T23:59:59.000Z

162

Recirculating rotary gas compressor  

DOE Patents (OSTI)

A positive displacement, recirculating Roots-type rotary gas compressor is described which operates on the basis of flow work compression. The compressor includes a pair of large diameter recirculation conduits which return compressed discharge gas to the compressor housing, where it is mixed with low pressure inlet gas, thereby minimizing adiabatic heating of the gas. The compressor includes a pair of involutely lobed impellers and an associated port configuration which together result in uninterrupted flow of recirculation gas. The large diameter recirculation conduits equalize gas flow velocities within the compressor and minimize gas flow losses. The compressor is particularly suited to applications requiring sustained operation at higher gas compression ratios than have previously been feasible with rotary pumps, and is particularly applicable to refrigeration or other applications requiring condensation of a vapor. 12 figs.

Weinbrecht, J.F.

1992-02-25T23:59:59.000Z

163

Recirculating rotary gas compressor  

DOE Patents (OSTI)

A positive displacement, recirculating Roots-type rotary gas compressor which operates on the basis of flow work compression. The compressor includes a pair of large diameter recirculation conduits (24 and 26) which return compressed discharge gas to the compressor housing (14), where it is mixed with low pressure inlet gas, thereby minimizing adiabatic heating of the gas. The compressor includes a pair of involutely lobed impellers (10 and 12) and an associated port configuration which together result in uninterrupted flow of recirculation gas. The large diameter recirculation conduits equalize gas flow velocities within the compressor and minimize gas flow losses. The compressor is particularly suited to applications requiring sustained operation at higher gas compression ratios than have previously been feasible with rotary pumps, and is particularly applicable to refrigeration or other applications requiring condensation of a vapor.

Weinbrecht, John F. (601 Oakwood Loop, NE., Albuquerque, NM 87123)

1992-01-01T23:59:59.000Z

164

Rotary kiln seal  

SciTech Connect

A rotary seal used to prevent the escape of contaminates from a rotating kiln incinerator. The rotating seal combines a rotating disc plate which is attached to the rotating kiln shell and four sets of non-rotating carbon seal bars housed in a primary and secondary housing and which rub on the sides of the disc. A seal air system is used to create a positive pressure in a chamber between the primary and secondary seals to create a positive air flow into the contaminated gas chamber. The seal air system also employs an air inlet located between the secondary and tertiary seals to further insure that no contaminates pass the seal and enter the external environment and to provide makeup air for the air which flows into the contaminated gas chamber. The pressure exerted by the seal bars on the rotating disc is controlled by means of a preload spring. The seal is capable of operating in a thermally changing environment where the both radial expansion and axial movement of the rotating kiln do not result in the failure of the seal.

Drexler, Robert L. (Idaho Falls, ID)

1992-01-01T23:59:59.000Z

165

Rotary kiln seal  

DOE Patents (OSTI)

A rotary seal used to prevent the escape of contaminants from a rotating kiln incinerator. The rotating seal combines a rotating disc plate which is attached to the rotating kiln shell and four sets of non-rotating carbon seal bars housed in a primary and secondary housing and which rub on the sides of the disc. A seal air system is used to create a positive pressure in a chamber between the primary and secondary seals to create a positive air flow into the contaminated gas chamber. The seal air system also employs an air inlet located between the secondary and tertiary seals to further insure that no contaminants pass the seal and enter the external environment and to provide makeup air for the air which flows into the contaminated gas chamber. The pressure exerted by the seal bars on the rotating disc is controlled by means of a preload spring. The seal is capable of operating in a thermally changing environment where the both radial expansion and axial movement of the rotating kiln do not result in the failure of the seal.

Drexler, R.L.

1990-10-17T23:59:59.000Z

166

Performance optimization of rotary dehumidifiers  

SciTech Connect

A rotary dehumidifier consists of a rotating porous matrix made of a desiccant with mechanically supporting materials. The dehumidification performance of a rotary dehumidifier wheel depends on its rotational speed, the sorption properties of the desiccant, the heat and mass transfer characteristics of the matrix, and the size of the dehumidifier. The effect of the rotational speed on the dehumidification performance of a rotary dehumidifier has been investigated by Zheng, Worek, and Novosel (1993). this paper extends that previous work and investigates the effects of desiccant sorption properties, the heat and mass transfer characteristics, and the size of the rotary dehumidifier on the dehumidification performance. The results show that the using desiccant materials in a rotary dehumidifier with different adsorption characteristics results in a wide variation in dehumidification performance. However, the maximum performance of a rotary dehumidifier occurs for a desiccant material having an isotherm shape that can be characterized to have a separation factor of 0.07. Also, as the desiccant moisture uptake increases, the dehumidifier performance also increases. However, the performance improvement for a desiccant matrix having a maximum moisture uptake of larger than 0.25 by weight is not significant. The heat and mass transfer properties and the size of rotary dehumidifier are characterized by the number of transfer units NTU. Generally, the larger the NTU, the better dehumidification performance. However, similar to the maximum moisture uptake, when the NTU is larger than 12, the performance will not improve significantly. Also, the dehumidifier with the most favorable adsorption characteristic has a slower rotational speed, which results in lower power requirements to rotate the desiccant wheel and smaller carry-over losses.

Zheng, W.; Worek, W.M. [Univ. of Chicago, IL (United States). Dept. of Mechanical Engineering; Novosel, D. [Gas Research Inst., Chicago, IL (United States)

1995-02-01T23:59:59.000Z

167

Natural Gas - U.S. Energy Information Administration (EIA) - U.S. Energy  

Gasoline and Diesel Fuel Update (EIA)

23, 2012 | Release Date: May 24, 23, 2012 | Release Date: May 24, 2012 | Next Release: May 31, 2012 Previous Issues Week: 01/19/2014 (View Archive) JUMP TO: In The News | Overview | Prices/Demand/Supply | Storage In the News: Natural Gas Rig Count Briefly Drops Below 600. The natural gas rotary rig count, as reported by Baker Hughes Incorporated, rose by 2 this week to 600, after falling to a 10-year low of 598 last week. After increasing modestly to 936 active rigs in the fall of 2011, the natural gas rig count has dropped sharply. The oil rig count, currently at 1,382, has generally risen steadily since 2009, largely in response to increasing crude oil prices. Natural gas rigs are currently down about 31 percent from their level at the same time last year, while oil rigs have risen by 45 percent over the

168

Solar-heated rotary kiln  

DOE Patents (OSTI)

A solar heated rotary kiln utilized for decomposition of materials, such as zinc sulfate is disclosed. The rotary kiln has an open end and is enclosed in a sealed container having a window positioned for directing solar energy into the open end of the kiln. The material to be decomposed is directed through the container into the kiln by a feed tube. The container is also provided with an outlet for exhaust gases and an outlet for spent solids, and rests on a tiltable base. The window may be cooled and kept clear of debris by coolant gases.

Shell, P.K.

1982-04-14T23:59:59.000Z

169

Rotary actuator utilizing a shape memory alloy  

SciTech Connect

An apparatus is described comprising; (a) rotary accumulator means for accumulating a length of a shape memory alloy wire; (b) the shape memory alloy wire attached at one end to a point fixed with respect to the rotary accumulator means and attached at a second end to the rotary accumulator means; (c) biasing means for biasing the rotary accumulator means to a first position; and (d) means for heating the shape memory alloy wire to cause the shape memory alloy wire to contract, thereby rotating the rotary accumulator means from the first position to a second position.

Bloch, J.T.

1988-08-09T23:59:59.000Z

170

U.S. Crude Oil and Natural Gas Active Well Service Rigs in operation  

Gasoline and Diesel Fuel Update (EIA)

Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1973 1,549 1,677 1,805 1,898 1,991 1,994 1,997 2,112 2,227 2,247 2,266 2,334 1974 2,401 2,436 2,470 2,513 2,555 2,525 2,494 2,483 2,473 2,488 2,503 2,543 1975 2,582 2,549 2,568 2,549 2,374 2,426 2,344 2,369 2,459 2,434 2,505 2,675 1976 2,612 2,490 2,521 2,597 2,575 2,607 2,606 2,656 2,652 2,639 2,601 2,660 1977 2,474 2,628 2,695 2,804 2,760 2,895 2,929 2,942 2,964 2,973 2,968 2,898 1978 2,810 2,906 2,899 2,997 2,996 2,987 3,006 3,089 3,073 3,078 2,958 3,063 1979 3,094 2,698 2,765 3,034 3,369 3,506 3,572 3,621 3,673 3,954 3,795 3,709 1980 3,855 3,923 4,010 3,871 4,032 4,112 4,092 4,155 4,277 4,290 4,281 4,172

171

Crude oil-directed weekly rig count surpassed 1,000 - Today in ...  

U.S. Energy Information Administration (EIA)

Solar › Energy in Brief ... Market Watch: Tropical Storm Lee combined with reduced holiday loads cut natural gas and electricity consumption over the weekend.

172

CURRENT PAPERS Stationary Rig Experiments on the Heat Extracting Power of Closed Thermosyphon Cooling Holes  

E-Print Network (OSTI)

portvan Page 8, penultmate lame, page 9, equatmn (25), and figure 16, m the of the eqwtlon:-quoted, the mdxes are incorrectly m-lttm, and the whole equatlcn s!uml.d rexd:-[C.ljg2;;$'835 (I- 0.0979 FP*4035) j z-------------------------------------------(o.4,5 fgs2 ' (1.05 FPJ- 1) Paga 15, equation (IO), ps hm been omitted from the right-hand side of the equatxon, and should mad:-Page 17, line 2, "them~ocyphon " should read "thermosyphon". Page 18, tie II, "caloulat~m " should head "calculatmns".

Dr. H. W. Hahnemann; Naticnal Ghs; Twwnz Est

1951-01-01T23:59:59.000Z

173

The semigroup of rigged annuli and the Teichmueller space of the annulus  

E-Print Network (OSTI)

Neretin and Segal independently defined a semigroup of annuli with boundary parametrizations, which is viewed as a complexification of the group of diffeomorphisms of the circle. By extending the parametrizations to quasisymmetries, we show that this semigroup is a quotient of the Teichmueller space of doubly-connected Riemann surfaces by a Z action. Furthermore, the semigroup can be given a complex structure in two distinct, natural ways. We show that these two complex structures are equivalent, and furthermore that multiplication is holomorphic. Finally, we show that the class of quasiconformally-extendible conformal maps of the disk to itself is a complex submanifold in which composition is holomorphic.

Radnell, David

2010-01-01T23:59:59.000Z

174

DOE-STD-1090-99; DOE Standard Hoisting and Rigging (Formerly...  

NLE Websites -- All DOE Office Websites (Extended Search)

the operator is not operating the forklift truck safely. 4. The operator is assigned to drive a different type of forklift truck. 5. A condition in the workplace changes in a...

175

Microsoft Word - 41888_SWPC_Adv Mat & Coating Test Rig_Factsheet...  

NLE Websites -- All DOE Office Websites (Extended Search)

steam generators, piping and ducting, fuel delivery skid, additional test sections, instrumentation and controls, and the exhaust systems for each test section. All...

176

The Rail Technology Unit The Application of the Roller Rigs to Railway  

E-Print Network (OSTI)

Jin a ; Ernie Pan b a Department of Engineering Mechanics, Shijiazhuang Railway Institute Mechanics, Shijiazhuang Railway Institute, Shijiazhuang 050043, China; b Department of Civil Engineering In recent years, piezoelectric and piezomagnetic materials have increasingly found applications in various

177

U.S. Crude Oil and Natural Gas Active Well Service Rigs in operation...  

Gasoline and Diesel Fuel Update (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1970's 2,008 2,490 2,486 2,601 2,828 2,989 3,399 1980's 4,089 4,849 4,249 3,733 4,659 4,716 3,037 3,059...

178

High bandwidth rotary fast tool servos and a hybrid rotary/linear electromagnetic actuator  

E-Print Network (OSTI)

This thesis describes the development of two high bandwidth short-stroke rotary fast tool servos and the hybrid rotary/linear electromagnetic actuator developed for one of them. Design insights, trade-off methodologies, ...

Montesanti, Richard Clement

2005-01-01T23:59:59.000Z

179

Rotary kilns - transport phenomena and transport processes  

Science Conference Proceedings (OSTI)

Rotary kilns and rotating industrial drying ovens are used for a wide variety of applications including processing raw minerals and feedstocks as well as heat-treating hazardous wastes. They are particularly critical in the manufacture of Portland cement. Their design and operation is critical to their efficient usage, which if done incorrectly can result in improperly treated materials and excessive, high fuel costs. This book treats all engineering aspects of rotary kilns, including thermal and fluid principles involved in their operation, as well as how to properly design an engineering process that uses rotary kilns. Chapter 1: The Rotary Kiln Evolution and Phenomenon Chapter 2: Basic Description of Rotary Kiln Operation Chapter 3: Freeboard Aerodynamic Phenomena Chapter 4: Granular Flows in Rotary Kilns Chapter 5: Mixing and Segregation Chapter 6: Combustion and Flame - includes section on types of fuels used in rotary kilns, coal types, ranking and analysis, petroleum coke combustion, scrap tire combustion, pulverized fuel (coal/coke) firing in kilns, pulverized fuel delivery and firing systems. Chapter 7: Freeboard Heat Transfer Chapter 8: Heat Transfer Processes in the Rotary Kiln Bed Chapter 9: Mass and Energy Balance Chapter 10: Rotary Kiln Minerals Process Applications.

Boateng, A.

2008-01-15T23:59:59.000Z

180

Natural Gas - U.S. Energy Information Administration (EIA) - U.S. Energy  

Gasoline and Diesel Fuel Update (EIA)

30, 2012 | Release Date: May 31, 30, 2012 | Release Date: May 31, 2012 | Next Release: June 7, 2012 Previous Issues Week: 12/29/2013 (View Archive) JUMP TO: In The News | Overview | Prices/Demand/Supply | Storage In the News: Natural Gas Rigs Decline in Key Areas Active natural gas rotary rigs currently total 594, according to the latest weekly data released by Baker Hughes Incorporated. According to Baker Hughes data, natural gas-directed horizontal rigs have driven the decline in total natural gas rigs over the past several months. Horizontal-directed natural gas rig counts have fallen to 411, from levels in the low-600s a year ago. Declines have occurred in key areas of dry shale gas production, particularly in Louisiana, where the Haynesville Shale is located. The number of horizontal natural gas rigs drilling in Louisiana has fallen from

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Floating seal system for rotary devices  

DOE Patents (OSTI)

This invention relates to a floating seal system for rotary devices to reduce gas leakage around the rotary device in a duct and across the face of the rotary device to an adjacent duct. The peripheral seal bodies are made of resilient material having a generally U-shaped cross section wherein one of the legs is secured to a support member and the other of the legs forms a contacting seal against the rotary device. The legs of the peripheral seal form an extended angle of intersection of about 10.degree. to about 30.degree. in the unloaded condition to provide even sealing forces around the periphery of the rotary device. The peripheral seal extends around the periphery of the support member except where intersected by radial seals which reduce gas leakage across the face of the rotary device and between adjacent duct portions. The radial seal assembly is fabricated from channel bars, the smaller channel bar being secured to the divider of the support member and a larger inverted rigid floating channel bar having its legs freely movable over the legs of the smaller channel bar forming therewith a tubular channel. A resilient flexible tube is positioned within the tubular channel for substantially its full length to reduce gas leakage across the tubular channel. A spacer extends beyond the face of the floating channel near each end of the floating channel a distance to provide desired clearance between the floating channel and the face of the rotary device.

Banasiuk, Hubert A. (Chicago, IL)

1983-01-01T23:59:59.000Z

182

Floating seal system for rotary devices  

DOE Patents (OSTI)

This invention relates to a floating seal system for rotary devices to reduce gas leakage around the rotary device in a duct and across the face of the rotary device to an adjacent duct. The peripheral seal bodies are made of resilient material having a generally U-shaped cross section wherein one of the legs is secured to a support member and the other of the legs forms a contacting seal against the rotary device. The legs of the peripheral seal form an extended angle of intersection of about 10[degree] to about 30[degree] in the unloaded condition to provide even sealing forces around the periphery of the rotary device. The peripheral seal extends around the periphery of the support member except where intersected by radial seals which reduce gas leakage across the face of the rotary device and between adjacent duct portions. The radial seal assembly is fabricated from channel bars, the smaller channel bar being secured to the divider of the support member and a larger inverted rigid floating channel bar having its legs freely movable over the legs of the smaller channel bar forming therewith a tubular channel. A resilient flexible tube is positioned within the tubular channel for substantially its full length to reduce gas leakage across the tubular channel. A spacer extends beyond the face of the floating channel near each end of the floating channel a distance to provide desired clearance between the floating channel and the face of the rotary device. 5 figs.

Banasiuk, H.A.

1983-08-23T23:59:59.000Z

183

Enclosed rotary disc air pulser  

DOE Patents (OSTI)

An enclosed rotary disc air pulser for use with a solvent extraction pulse olumn includes a housing having inlet, exhaust and pulse leg ports, a shaft mounted in the housing and adapted for axial rotation therein, first and second disc members secured to the shaft within the housing in spaced relation to each other to define a chamber therebetween, the chamber being in communication with the pulse leg port, the first disc member located adjacent the inlet port, the second disc member being located adjacent the exhaust port, each disc member having a milled out portion, the disc members positioned on the shaft so that as the shaft rotates, the milled out portions permit alternative cyclical communication between the inlet port and the chamber and the exhaust port and the chamber.

Olson, A. L. (Idaho Falls, ID); Batcheller, Tom A. (Idaho Falls, ID); Rindfleisch, J. A. (Arco, ID); Morgan, John M. (Arco, ID)

1989-01-01T23:59:59.000Z

184

Enclosed rotary disc air pulser  

DOE Patents (OSTI)

This invention is comprised of an enclosed rotary disc air pulser for use with a solvent extraction pulse column includes a housing having inlet, exhaust and pulse leg ports, a shaft mounted in the housing and adapted for axial rotation therein, first and second disc members secured to the shaft within the housing in spaced relation to each other to define a chamber there between, the chamber being in communication with the pulse leg port, and first disc member located adjacent the inlet port, the second disc member being located adjacent the exhaust port, each disc member having a milled out portion, the disc members positioned on the shaft so that as the shaft rotates, the milled out portions permit alternative cyclical communication between the inlet port and the chamber and the exhaust port and chamber. 5 figs.

Olson, A.L.; Batcheller, T.A.; Rindfleisch, J.A.; Morgan, J.M.

1988-08-12T23:59:59.000Z

185

Experimental Results on Advanced Rotary Desiccant Dehumidifiers  

E-Print Network (OSTI)

The Solar Energy Research Institute (SERI) has developed the Cyclic Test Facility (CTF) to develop and validate analytical methods for evaluating and predicting the performance of advanced rotary dehumidifiers. This paper describes the CTF, the dehumidifiers tested at the CTF, and the analytical methods used. The results reported provide an engineering data base and a design tool for evaluating rotary dehumidifiers for desiccant cooling applications.

Barathan, D.; Parsons, J. M.; MaClaine-Cross, I.

1986-01-01T23:59:59.000Z

186

Experimental results on advanced rotary desiccant dehumidifiers  

DOE Green Energy (OSTI)

The Solar Energy Research Institute (SERI) has developed the Cyclic Test Facility (CTF) to develop and validate analytical methods for evaluating and predicting the performance of advanced rotary dehumidifiers. This paper describes the CTF, the dehumidifiers tested at the CTF, and the analytical methods used. The results reported provide an engineering data base and a design tool for evaluating rotary dehumidifiers for desiccant cooling applications.

Bharathan, D.; Parsons, J.; Maclaine-cross, I.

1986-08-01T23:59:59.000Z

187

Coal desulfurization in a rotary kiln combustor  

Science Conference Proceedings (OSTI)

The purpose of this project was to demonstrate the combustion of coal and coal wastes in a rotary kiln reactor with limestone addition for sulfur control. The rationale for the project was the perception that rotary systems could bring several advantages to combustion of these fuels, and may thus offer an alternative to fluid-bed boilers. Towards this end, an existing wood pyrolysis kiln (the Humphrey Charcoal kiln) was to be suitably refurbished and retrofitted with a specially designed version of a patented air distributor provided by Universal Energy, Inc. (UEI). As the project progressed beyond the initial stages, a number of issues were raised regarding the feasibility and the possible advantages of burning coals in a rotary kiln combustor and, in particular, the suitability of the Humphrey Charcoal kiln as a combustor. Instead, an opportunity arose to conduct combustion tests in the PEDCO Rotary Cascading-Bed Boiler (RCBB) commercial demonstration unit at the North American Rayon CO. (NARCO) in Elizabethton, TN. The tests focused on anthracite culm and had two objectives: (a) determine the feasibility of burning anthracite culms in a rotary kiln boiler and (b) obtain input for any further work involving the Humphrey Charcoal kiln combustor. A number of tests were conducted at the PEDCO unit. The last one was conducted on anthracite culm procured directly from the feed bin of a commercial circulating fluid-bed boiler. The results were disappointing; it was difficult to maintain sustained combustion even when large quantities of supplemental fuel were used. Combustion efficiency was poor, around 60 percent. The results suggest that the rotary kiln boiler, as designed, is ill-suited with respect to low-grade, hard to burn solid fuels, such as anthracite culm. Indeed, data from combustion of bituminous coal in the PEDCO unit suggest that with respect to coal in general, the rotary kiln boiler appears inferior to the circulating fluid bed boiler.

Cobb, J.T. Jr.

1992-09-11T23:59:59.000Z

188

Identifiering av synkronmaskinsmodell genom SSFR-test.  

E-Print Network (OSTI)

?? At the Division of Electricity at Uppsala University there is an experimental rig for hydroelectric generators. The experimental rig’s vital part is a 12-pole… (more)

Malmberg, Johan

2011-01-01T23:59:59.000Z

189

Word Pro - S5  

U.S. Energy Information Administration (EIA) Indexed Site

Crude Oil and Natural Gas Resource Development Indicators Rotary Rigs in Operation by Type, 1949-2012 Rotary Rigs in Operation by Type, Monthly Active Well Service Rig Count, Monthly Total Wells Drilled by Type, 1949-2010 . 76 U.S. Energy Information Administration / Monthly Energy Review November 2013 Total 1950 1955 1960 1965 1970 1975 1980 1985 1990 1995 2000 2005 2010 0 1 2 3 4 Thousand Rigs 1950 1955 1960 1965 1970 1975 1980 1985 1990 1995 2000 2005 2010 0 10 20 30 40 50 Thousand Wells Dry Wells Crude Oil Wells Web Page: http://www.eia.gov/totalenergy/data/monthly/#crude. Sources: Tables 5.1 and 5.2. Crude Oil J FMAMJ J A SOND J FMAMJ J A SOND J FMAMJ J

190

Word Pro - S5  

U.S. Energy Information Administration (EIA) Indexed Site

Crude Oil and Natural Gas Crude Oil and Natural Gas Resource Development Figure 5.1 Crude Oil and Natural Gas Resource Development Indicators Rotary Rigs in Operation by Type, 1949-2012 Rotary Rigs in Operation by Type, Monthly Active Well Service Rig Count, Monthly Total Wells Drilled by Type, 1949-2010 . 76 U.S. Energy Information Administration / Monthly Energy Review November 2013 Total 1950 1955 1960 1965 1970 1975 1980 1985 1990 1995 2000 2005 2010 0 1 2 3 4 Thousand Rigs 1950 1955 1960 1965 1970 1975 1980 1985 1990 1995 2000 2005 2010 0 10 20 30 40 50 Thousand Wells Dry Wells Crude Oil Wells Web Page: http://www.eia.gov/totalenergy/data/monthly/#crude. Sources: Tables 5.1 and 5.2.

191

EXPERIMENTAL EVALUATION OF THE COMBUSTION HAZARD TO THE EXPERIMENTAL GAS- COOLED REACTOR-PRELIMINARY BURNING RIG EXPERIMENTS  

SciTech Connect

>An assembly was constructed which simulated the moderator coolant annulus in the Experimental Gas-Cooled Reactor. This assembly was preheated to various temperatures and air was passed through the coolant annulus. Under certain conditions it was demonstrated that self-sustained combustion of the graphite could occur. Rates of temperature rise were generally less than 1 deg C/ min until the graphite temperature exceeded 700 deg C and then rise rates became very high. In these cxperimcnts, the assembly was not operated in such a manner as to give ignition temperatures eharaeteristic of the EGCR. These tests were designed only to investigate the effects of changing such parameters as the rate of coolant flow, air humidity, prior oxidation on the graphite, and air inlet temperature. A later series of experiments to more closely duplicate the EGCR operating conditions was completed and will be reported in a second report, HW- 71182. (auth)

Dahl, R.E.

1961-11-01T23:59:59.000Z

192

Compact fast analyzer of rotary cuvette type  

DOE Patents (OSTI)

A compact fast analyzer of the rotary cuvette type is provided for simultaneously determining concentrations in a multiplicity of discrete samples using either absorbance or fluorescence measurement techniques. A rigid, generally rectangular frame defines optical passageways for the absorbance and fluorescence measurement systems. The frame also serves as a mounting structure for various optical components as well as for the cuvette rotor mount and drive system. A single light source and photodetector are used in making both absorbance and fluorescence measurements. Rotor removal and insertion are facilitated by a swing-out drive motor and rotor mount. BACKGROUND OF THE INVENTION The invention relates generally to concentration measuring instruments and more specifically to a compact fast analyzer of the rotary cuvette type which is suitable for making either absorbance or fluorescence measurements. It was made in the course of, or under, a contract with the U.S. Atomic Energy Commission.

Thacker, Louis H. (Knoxville, TN)

1976-01-01T23:59:59.000Z

193

Rotary Mode Core Sample System availability improvement  

SciTech Connect

The Rotary Mode Core Sample System (RMCSS) is used to obtain stratified samples of the waste deposits in single-shell and double-shell waste tanks at the Hanford Site. The samples are used to characterize the waste in support of ongoing and future waste remediation efforts. Four sampling trucks have been developed to obtain these samples. Truck I was the first in operation and is currently being used to obtain samples where the push mode is appropriate (i.e., no rotation of drill). Truck 2 is similar to truck 1, except for added safety features, and is in operation to obtain samples using either a push mode or rotary drill mode. Trucks 3 and 4 are now being fabricated to be essentially identical to truck 2.

Jenkins, W.W.; Bennett, K.L.; Potter, J.D. [Westinghouse Hanford Co., Richland, WA (United States); Cross, B.T.; Burkes, J.M.; Rogers, A.C. [Southwest Research Institute (United States)

1995-02-28T23:59:59.000Z

194

High Pressure Rotary Shaft Sealing Mechanism  

DOE Patents (OSTI)

A laterally translatable pressure staged rotary shaft sealing mechanism having a seal housing with a shaft passage therein being exposed to a fluid pressure P1 and with a rotary shaft being located within the shaft passage. At least one annular laterally translatable seal carrier is provided. First and second annular resilient sealing elements are supported in axially spaced relation by the annular seal carriers and have sealing relation with the rotary shaft. The seal housing and at least one seal carrier define a first pressure staging chamber exposed to the first annular resilient sealing element and a second pressure staging chamber located between and exposed to the first and second annular resilient sealing elements. A first fluid is circulated to the first pressure chamber at a pressure P1, and a second staging pressure fluid is circulated to the second pressure chamber at a fraction of pressure P1 to achieve pressure staging, cooling of the seals. Seal placement provides hydraulic force balancing of the annular seal carriers.

Dietle, Lannie (Sugar Land, TX); Gobeli, Jeffrey D. (Houston, TX)

2001-05-08T23:59:59.000Z

195

Coal desulfurization in a rotary kiln combustor  

Science Conference Proceedings (OSTI)

BCR National Laboratory (BCRNL) has initiated a project aimed at evaluating the technical and economic feasibility of using a rotary kiln, suitably modified, to burn Pennsylvania anthracite wastes, co-fired with high-sulfur bituminous coal. Limestone will be injected into the kiln for sulfur control, to determine whether high sulfur capture levels can be achieved with high sorbent utilization. The principal objectives of this work are: (1) to prove the feasibility of burning anthracite refuse, with co-firing of high-sulfur bituminous coal and with limestone injection for sulfur emissions control, in a rotary kiln fitted with a Universal Energy International (UEI) air injector system; (2) to determine the emissions levels of SO{sub x} and NO{sub x} and specifically to identify the Ca/S ratios that are required to meet New Source Performance Standards; (3) to evaluate the technical and economic merits of a commercial rotary kiln combustor in comparison to fluidized bed combustors; and, (4) to ascertain the need for further work, including additional combustion tests, prior to commercial application, and to recommend accordingly a detailed program towards this end.

Cobb, J.T. Jr.

1990-08-15T23:59:59.000Z

196

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on...

197

A unidirectional rotary solenoid as applied to stronglinks  

Science Conference Proceedings (OSTI)

This paper describes the design goals and results of an advanced development stronglink project with special emphasis on a new rotary solenoid concept. 10 figs.

Kenderdine, E.W.

1988-01-01T23:59:59.000Z

198

Coal desulfurization in a rotary kiln combustor  

Science Conference Proceedings (OSTI)

Several issues that could have an impact on the capability to burn anthracite culm in a rotary bed boiler were identified; specifically, questions were raised concerning the specifications of the anthracite culm itself and some relating to the equipment. The anthracite culm delivered was wet, (with more than 10 percent moisture), and coarser than feed material for fluidized boilers. It was felt that using finer fuel, ensuring that it is largely dry, would aid the combustion of anthracite culm. It also appeared that if provisions were made for more efficient internal and external recycle of ash, this would also enhance the combustion of this fuel. Accordingly, the decision was made to conduct an additional campaign of tests that would incorporate these changes. The tests, conducted on July 15 and 16, 1991, involved an anthracite culm that was, in fact, obtained from a fluidized bed a heating value of 3,000 Btu/lb and came with a top size of 1/4-inch. Despite these changes, sustained combustion could not be achieved without the use of large quantities of supplemental fuel. Based on these tests, we tend to conclude that the rotary kiln is ill suited for the combustion of hard-to-burn, low-grade solid fuels like anthracite culm.

Cobb, J.T. Jr.

1991-08-29T23:59:59.000Z

199

Results of the 1000 Hour Rotary Microfilter Endurance Test  

Stellite on Nitronic 60. 8 SRNL-L3100-2010-00229 Rotary Microfilter 1000 Hour Test Flux Data for 1000 Hour Test 0 1 2 3 4 5 6 0 100 200 300 400 500 ...

200

TESTING OF THE DUAL ROTARY FILTER SYSTEM  

SciTech Connect

The Savannah River National Laboratory (SRNL) installed and tested two hydraulically connected SpinTek rotary microfilter (RMF) units to determine the behavior of a multiple filter system. Both units were successfully controlled by a control scheme written in DELTA-V architecture by Savannah River Remediation (SRR) Process Control Engineering personnel. The control system was tuned to provide satisfactory response to changing conditions during the operation of the multi-filter system. Stability was maintained through the startup and shutdown of one of the filter units while the second was still in operation. The installation configuration originally proposed by the Small Colum Ion Exchange (SCIX) project of independent filter and motor mountings may be susceptible to vibration. Significant stiffening of the filter and motor mounts was required to minimize the vibration. Alignment of the motor to the filter was a challenge in this test configuration. The deployment configuration must be easy to manipulate and allow for fine adjustment. An analysis of the vibration signature of the test system identified critical speeds. Whether it corresponds to the resonance frequency of a rotor radial vibration mode that was excited by rotor unbalance is uncertain based upon the measurements. A relative motion series should be completed on the filter with the final shaft configuration to determine if the resonances exist in the final filter design. The instrumentation selected for deployment, including the concentrate discharge control valve and flow meters, performed well. Automation of the valve control integrated well with the control scheme and when used in concert with the other control variables, allowed automated control of the dual RMF system. The one area of concern with the instrumentation was the condition resulting when the filtrate flow meter operated with less than three gpm. This low flow was at the lower range of performance for the flow meter. This should not be an issue in deployment where the desired flow rate will be within the normal operating range of the meter. Testing demonstrated that the use of a flexible line for the filtrate discharge is highly desired at the outlet of the rotary union to transition to the system piping. Isolating the vibration from the rotary union will significantly improve the lifetime of the seals. Methods to monitor and isolate individual filters should be considered during deployment. The ability to diagnose issues and isolate individual filters would allow isolation prior to failure. Thus, filters may be cleaned or repaired instead of requiring complete replacement if the condition were to continue unnoticed. Isolating the filtrate line of each filter during startup will minimize the premature buildup of solids on the filter disks. Several tests have shown that the method of filter startup can improve performance lifetime of the filters. The installation must factor in an air inlet for the draining of a filter that does not involve a reverse flow through the filter disks. The reverse flow may cause deformation of the disks or may damage other components of the filters themselves.

Herman, D.; Fowley, M.; Stefanko, D.

2011-08-29T23:59:59.000Z

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Wednesday, 28 April 2010 00:00 Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

202

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Wednesday, 28 April 2010 00:00 Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

203

Microwave lamp with multi-purpose rotary motor  

DOE Patents (OSTI)

In a microwave powered electrodeless lamp, a single rotary motor is used to (a) rotate the bulb and (b) provide rotary motion to a blower or pump means for providing cooling fluid to the magnetron and/or to a forced gas cooler for providing cooling gas to the bulb. The blower may consist of only of an impeller without the usual blower housing. The motor, bulb stem and bulb, or motor, bulb stem, bulb and blower may be formed as an integral unit so as to facilitate replacement. 8 figs.

Ury, M.G.; Turner, B.; Wooten, R.D.

1999-02-02T23:59:59.000Z

204

Microwave lamp with multi-purpose rotary motor  

DOE Patents (OSTI)

In a microwave powered electrodeless lamp, a single rotary motor is used to a) rotate the bulb and b) provide rotary motion to a blower or pump means for providing cooling fluid to the magnetron and/or to a forced gas cooling for providing cooler gas to the bulb. The blower may consist of only of an impeller without the usual blower housing. The motor, bulb stem and bulb, or motor, bulb stem, bulb and blower may be formed as an integral unit so as to facilitate replacement.

Ury, Michael G. (Bethesda, MD); Turner, Brian (Myersville, MD); Wooten, Robert D. (Rockville, MD)

1999-01-01T23:59:59.000Z

205

BACKPRESSURE TESTING OF ROTARY MICROFILTER DISKS  

Science Conference Proceedings (OSTI)

The Savannah River National Laboratory (SRNL), under the Department of Energy (DOE) Office of Environmental Management (EM), is modifying and testing the SpinTek{trademark} rotary microfilter (RMF) for radioactive filtration service in the Department of Energy (DOE) complex. The RMF has been shown to improve filtration throughput when compared to other conventional methods such as cross-flow filtration. A concern with the RMF was that backpressure, or reverse flow through the disk, would damage the filter membranes. Reverse flow might happen as a result of an inadvertent valve alignment during flushing. Testing was completed in the Engineering Development Laboratory (EDL) located in SRNL to study the physical effects of backpressure as well as to determine the maximum allowable back-pressure for RMF disks. The RMF disks tested at the EDL were manufactured by SpinTek{trademark} Filtration and used a Pall Corporation PMM050 filter membrane (0.5 micron nominal pore size) made from 316L stainless steel. Early versions of the RMF disks were made from synthetic materials that were incompatible with caustic solutions and radioactive service as well as being susceptible to delaminating when subjected to backpressure. Figure 1-1 shows the essential components of the RMF; 3 rotating disks and 3 stationary turbulence promoters (or shear elements) are shown. Figure 1-2 show the assembly view of a 25 disk RMF proposed for use at the Savannah River Site (SRS) and at the Hanford Facility. The purpose of the testing discussed in this report was to determine the allowable backpressure for RMF disks as well as study the physical effects of backpressure on RMF disks made with the Pall PMM050 membrane. This was accomplished by pressurizing the disks in the reverse flow direction (backpressure) until the test limit was reached or until membrane failure occurred. Backpressure was applied to the disks with air while submerged in deionized (DI) water. This method provided a visual representation of membrane integrity via bubble flow patterns. Membrane failure was defined as the inability to filter effectively at the nominal filter pore size. Effective filtration was determined by turbidity measurements of filtrate that was produced by applying forward-pressure to the disks while submerged in a representative simulant. The representative simulant was Tank 8F simulated sludge produced for SRNL by Optima Chemical. Two disks were tested. Disk 1 was tested primarily to determine approximate levels of backpressure where membrane failure occurred. These levels were then used to define the strategy for testing the Disk 2; a strategy that would better define and quantify the mode of failure.

Fowley, M.; Herman, D.

2011-04-14T23:59:59.000Z

206

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

207

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

208

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

209

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

210

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

211

Micro rotary machine and methods for using same  

SciTech Connect

A micro rotary machine may include a micro actuator and a micro shaft coupled to the micro actuator. The micro shaft comprises a horizontal shaft and is operable to be rotated by the micro actuator. A micro tool is coupled to the micro shaft and is operable to perform work in response to motion of the micro shaft.

Stalford, Harold L. (Norman, OK)

2012-04-17T23:59:59.000Z

212

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

213

EVALUATION OF ALTERNATIVE FILTER MEDIA FOR THE ROTARY MICROFILTER  

SciTech Connect

SRS is currently developing and testing several processes to treat high level radioactive liquid waste. These processes include the Integrated Salt Disposition Process (ISDP), the Salt Waste Processing Facility (SWPF), and the Small Column Ion Exchange Process (SCIX). Each of these processes has a solid-liquid separation process that limits its throughput. SRNL researchers identified and tested the rotary microfilter as a technology to increase solid-liquid separation throughput. The testing showed significant improvement in filter flux with the rotary microfilter over the baseline crossflow filter (i.e., 2.5-6.5X during scoping tests, as much as 10X in actual waste tests, and approximately 3X in pilot-scale tests). SRNL received funding from DOE EM-21, and subsequently DOE EM-31 to develop the rotary microfilter for high level radioactive service. The work has included upgrading the rotary microfilter for radioactive service, testing with simulated SRS waste streams, and testing it with simulated Hanford waste streams. While the filtration rate is better than that obtained during testing of crossflow filters, the authors believe the rotary microfilter throughput can be improved by using a better filter membrane. The rotary microfilter membrane is made of stainless steel (Pall PMM050). Previous testing, funded by DOE EM-21, showed that asymmetric filters composed of a ceramic membrane on top of a stainless steel support produced higher filter flux than 100% stainless steel symmetric filters in crossflow filter tests. In that testing, the Pall Accusep and Graver filters produced 13-21% larger filter flux than the baseline 0.1 {micro}m Mott filter. While the improvement in flux is not as dramatic as the improvement of the rotary filter over a crossflow filter, a 13-21% increase could reduce the lifetime of a 30 year process by 4-6 years, with significant cost savings. Subsequent rotary filter testing showed the Pall PMM050 stainless steel filter membrane produced higher flux than the Mott filter media in bench-scale and pilot-scale testing. The Accusep and Graver filter media were not evaluated in that testing, because they are not available as flat sheets. The Accusep filter was developed at ORNL and licensed to Pall Corporation. This filter has a stainless steel support structure with a zirconium oxide ceramic membrane. The pore size is 0.1 {micro}m absolute. The Graver filter has a stainless steel support structure with a titanium dioxide ceramic membrane. The pore size is 0.07 {micro}m absolute. SRNL and ORNL are working together to develop filter media similar to the Accusep and Graver media, and to test them in a bench-scale filtration apparatus to attempt to improve the throughput of the rotary microfilter. This report describes the effort.

Poirier, M.; Herman, D.; Bhave, R.

2011-09-13T23:59:59.000Z

214

Type I Interferon is Not Just for Viruses: Cytosolic Sensing of Bacterial Nucleic Acids  

E-Print Network (OSTI)

mechanism of RIG-I helicase and activation of antiviraltriphosphate by RIG-I helicase requires short blunt double-Fujita, T. (2004). The RNA helicase RIG-I has an essential

Monroe, Kathryn McGee

2011-01-01T23:59:59.000Z

215

Non-nucleic acid based viral recognition  

E-Print Network (OSTI)

5'  triphosphate  by  RIG-­?I  helicase  requires   short  mechanism  of  RIG-­?I   helicase  and  activation  of  T.  Fujita.  2004.  The  RNA  helicase  RIG-­?I  has  an  

Barbalat, Roman

2011-01-01T23:59:59.000Z

216

NETL: Methane Hydrates - ANS Research Project - The Doyon 14...  

NLE Websites -- All DOE Office Websites (Extended Search)

Doyon 14 Rig The Doyon 14 rig is a fully-integrated self-propelled, wheel-mounted rig developed on the North Slope and built in 1986. Doyon Drilling Inc. (DDI) operates on the...

217

A pilgrim's guide to the Hidden Land of Sikkim proclaimed as a treasure by Rig 'dzin rgod kyi ldem 'phru can  

E-Print Network (OSTI)

Q~·~J5I'~ ~'~'33'33'i' ~~'~;S.t;·~·,.t;·~IIlJ5l'{t Moreover, when it came to the time of throwing grains in the air during the elaborate consecration ceremonies of that particular 'Stiipa of the Self-originated Crystal [image]' and the 'Stiipa... boulder in front of [the spring] with eight qualities, leaving his footprint as the support of blessings. Turning his face and gazing towards the southwest, he said: 'ITI SAMA Y A. Seal! Seal!' ~a.·~~·3·~·2f~·~·~:,¥~·a.!·~~·~~~·~t;'~~·t;I·~. ~t...

Boord, Martin J.

218

Thermo-Mechanical Performance of 230-345kV High Pressure Pipe Type Cable Systems: Selection of Full Size Test Rig  

Science Conference Proceedings (OSTI)

This is a front-end project to the wider experimental study of the thermo-mechanical performance of high-pressure fluid-filled (HPFF) transmission class cables in pipe systems. The project first reviews published work on the mechanisms of deterioration of HPFF cables due to thermo-mechanical bending activity (TMB). The principal mechanisms are the reduction in electrical strength caused by a) damage and opening of the outer electrostatic shield layers and b) the increase in the size of the fluid filled b...

2004-12-27T23:59:59.000Z

219

Rig 'dzin Tshe dbang mchog grub (1761-1829) et la constitution du rNying ma rgyud 'bum de sDe dge  

E-Print Network (OSTI)

les textes en une collection à ‘Ug palung, le fief de la lignée Zur3. Un article plus récent encore de Mi Nyag Thubbstan chos dar fait le point sur les diverses versions existantes, mentionnantd’ailleurs un certain nombre d’entre elles qui ne sont... and the Bai-ro- rgyud-‘bum”, p. 9. 4 Mi nyag Thub bstan chos dar, “rNying ma rgyud 'bum gyi mtshams sbyor”, passim. 5 Voir Achard, “ La liste des Tantras du rNying ma’i rgyud ‘bum selon l’édition établie par Kun mkhyen ‘Jigs med gling pa”, Revue d...

Achard, Jean-Luc

2003-01-01T23:59:59.000Z

220

Solids transportation model of an industrial rotary dryer  

SciTech Connect

A complete simulation model has been developed for an industrial rotary dryer to account for the heat and mass exchange between the solids and the gas. This simulator is mainly composed of three models: solids transportation model, furnace model, and gas model. The solids transportation model is the modified Cholette-Cloutier model. It consists of a series of interactive reservoirs which are subdivided into an active and dead compartments to account for the characteristic extended tail of the residence time distribution (RTD) curves observed in industrial dryers. To expand the validity of the model, experiments have been performed in an industrial rotary dryer to obtain RTD curves under different mineral concentrate and gas flow rates. This paper describes these experiments and presents the variation of the average residence time and model parameters as function of solids and gas flow rates.

Renaud, M.; Thibault, J.; Trusiak, A.

2000-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Skew and twist resistant hydrodynamic rotary shaft seal  

DOE Patents (OSTI)

A hydrodynamically lubricated squeeze packing type rotary shaft seal suitable for lubricant retention and environmental exclusion which incorporates one or more resilient protuberances which cooperate with the gland walls to hold the seal straight in its installation groove in unpressurized and low pressure lubricant retention applications thereby preventing skew-induced wear caused by impingement of abrasive contaminants present in the environment, and which also serve as radial bearings to prevent tipping of the seal within its installation gland. 14 figs.

Dietle, L.; Kalsi, M.S.

1999-02-23T23:59:59.000Z

222

Skew and twist resistant hydrodynamic rotary shaft seal  

DOE Patents (OSTI)

A hydrodynamically lubricated squeeze packing type rotary shaft seal suitable for lubricant retention and environmental exclusion which incorporates one or more resilient protuberances which and cooperate with the gland walls to hold the seal straight in its installation groove in unpressurized and low pressure lubricant retention applications thereby preventing skew-induced wear caused by impingement of abrasive contaminants present in the environment, and which also serve as radial bearings to prevent tipping of the seal within its installation gland.

Dietle, Lannie (Sugar Land, TX); Kalsi, Manmohan Singh (Houston, TX)

1999-01-01T23:59:59.000Z

223

Rotary union for use with ultrasonic thickness measuring probe  

DOE Patents (OSTI)

A rotary union for rotatably supporting an ultrasonic probe operable to nondestructively measure the thickness of steam generator tubes to determine the amount of corrosion experienced by the tubes includes a stationary body having a bore therethrough and an outlet drain, and a fitting rotatably mounted within the upper end of the body. The fitting has a bore aligned with the bore of the body. An electrical cable positioned within a water supply tube in an annular arrangement passes through the bore of the body and the bore of the fitting. This annular arrangement, in turn, is positioned within a connector element which extends outwardly from the fitting bore and is connected to the ultrasonic probe. An elastomeric lower bushing seals the annular arrangement to the lower end of the rotary union body and an elastomeric upper bushing seals the connector element to the fitting to permit the connector element and the ultrasonic probe connected thereto to rotate with the fitting relative to the body. The lower and upper bushings permit water to be passed through the annular arrangement and into the ultrasonic probe and thereafter discharged between the annular arrangement and the connector element to the outlet drain of the rotary union body. 5 figs.

Nachbar, H.D.

1992-09-15T23:59:59.000Z

224

Evaluation of Alternative Filter Media for the Rotary Microfilter  

SciTech Connect

The Savannah River Site is currently developing and testing several processes to treat high level radioactive liquid waste. Each of these processes has a solid-liquid separation process that limits its throughput. Savannah River National Laboratory researchers identified and tested the rotary microfilter as a technology to increase solid-liquid separation throughput. The authors believe the rotary microfilter throughput can be improved by using a better filter membrane. Previous testing showed that asymmetric filters composed of a ceramic membrane on top of a stainless steel support produced higher filter flux than 100% stainless steel symmetric filters in crossflow filter tests. Savannah River National Laboratory and Oak Ridge National Laboratory are working together to develop asymmetric ceramic ? stainless steel composite filters and asymmetric 100% stainless steel filters to improve the throughput of the rotary microfilter. The Oak Ridge National Laboratory Inorganic Membrane Group fabricated samples of alternative filter membranes. In addition, Savannah River National Laboratory obtained samples of filter membranes from Pall, Porvair, and SpinTek. They tested these samples in a static test cell with feed slurries containing monosodium titanate and simulated sludge.

Poirier, M. R.; Herman, D. T.; Bhave, R.

2011-11-09T23:59:59.000Z

225

Further Characterization of New NiTi Wire and Rotary Endodontic ...  

Science Conference Proceedings (OSTI)

Presentation Title, Further Characterization of New NiTi Wire and Rotary ... Higher-resolution transmission electron microscopy examination of M-Wire used to ...

226

Microsoft Word - nga2010_sum_hghlght _4_.doc  

Annual Energy Outlook 2012 (EIA)

levels of production and higher rig counts, both keeping downward pressure on prices. Shale production grew year- on-year, as did the number of horizontal rigs. Horizontal...

227

Word Pro - S5  

U.S. Energy Information Administration (EIA) Indexed Site

77 77 Table 5.1 Crude Oil and Natural Gas Drilling Activity Measurements (Number of Rigs) Rotary Rigs in Operation a Active Well Service Rig Count c By Site By Type Total b Onshore Offshore Crude Oil Natural Gas 1950 Average ........................ NA NA NA NA 2,154 NA 1955 Average ........................ NA NA NA NA 2,686 NA 1960 Average ........................ NA NA NA NA 1,748 NA 1965 Average ........................ NA NA NA NA 1,388 NA 1970 Average ........................ NA NA NA NA 1,028 NA 1975 Average ........................ 1,554 106 NA NA 1,660 2,486 1980 Average ........................ 2,678 231 NA NA 2,909 4,089 1985 Average ........................ 1,774 206 NA NA

228

Power Production from Geothermal Brine with the Rotary Separator Turbine  

SciTech Connect

The rotary separator turbine is a new turbine device that operates with gas-liquid mixtures. This device achieves complete gas-liquid separation, generates power from the liquid and repressurizes the liquid. The use of the rotary separator turbine for geothermal power generation was investigated on this program. A pilot scale unit was designed and tested. Tests were conducted with a clean water/steam mixture and with geothermal brine/steam flows at East Mesa, California; Raft River, Idaho; and Roosevelt Hot Springs, Utah. The test results were used to calculate the performance advantage of a rotary separator turbine power system compared to a flash steam power system and a binary power system. The calculated performance advantages were then used to estimate market potential for wellhead and central station Biphase units. The measured performance in the laboratory and in the field agreed to within {+-} 10% of the predicted values. The design goal of 20 kWe was generated both in the laboratory and from brine. Separated steam quality was measured to be greater than 99.96% at all three geothermal resources and in the laboratory. Brine pressure leaving the test unit was greater than reinjection pressure requirements. Maximum brine outlet pressure of 90 psig was demonstrated. The measured performance values would result in a 34% increase in electric power production above a single stage flash steam system. Increasing the size from the pilot size unit (20kWe) to a wellhead unit (2000 kWe) gave a calculated performance advantage of 40%. Based on these favorable results, design, construction and testing of a full-size well-head unit was initiated.

Cerini, Donald J.; Hays, Lance G.

1980-12-01T23:59:59.000Z

229

A rotary-airlock valve resists abrasive mixtures  

SciTech Connect

Hill and Griffith (H and G, Cincinnati, Ohio) is a leading supplier of custom-blended additives to founderies. Thousands of tons of clay and carbon blends such as bentonite, gilsonite and pulverized coal, pass through the company's rotary-airlock feeding system each month. H and G's original rotary valves had cylinders lined with chrome, and closed-end rotors with tips made from nickel-chromium alloys. These valves remained in service for a maximum of only three months each. During that time, the abrasive mixtures passing through the valves virtually eroded them, increasing tolerances and causing significant air leakage. The leaks caused the pneumatic line to plug up, reducing the velocity of the line below the minimum level needed to carry any material. To overcome the leakage, a second blower was added to the system. This unit supplied an additional 40 brake hp to the pneumatic-conveying line. With constant maintenance of the valve and the continuous operation of both blowers, H and G was able to extend the valve's life by nine months. After 20 years of trying valves with various configuration, H and G installed a Smoot Type 6 rotary-airlock valve in September of 1985. The new valve's internals were made from abrasion-resistant grades of NiHard and Stellite. This combination of alloys prolonged the active life of the valve by improving its abrasion resistance. During its first year, the Smoot valve did not break down, leak air or require use of the secondary blower. After its first year of service no wear was found on the valve's internal surfaces. Another mechanical analysis was performed in 1991, after five additional years of valve operation. The valve, which had now handled more than 250,000 tons of product, showed minimal wear. H and G's capital costs had been reduced from 25[cents]/ton to 3[cents]/ton by the new valve.

Not Available

1993-03-01T23:59:59.000Z

230

Skew And Twist Resistant Hydrodynamic Rotary Shaft Seal  

SciTech Connect

A hydrodynamically lubricated squeeze packing type rotary shaft seal suitable for lubricant retention and environmental exclusion which incorporates one or more resilient protuberances which and cooperate with the gland walls to hold the seal straight in its installation groove in unpressurized and low pressure lubricant retention applications thereby preventing skew-induced wear caused by impingement of abrasive contaminants present in the environment, and which also serve as radial bearings to prevent tipping of the seal within its installation gland. Compared to prior art, this invention provides a dramatic reduction of seal and shaft wear in abrasive environments and provides a significant increase in seal life.

Dietle, Lannie (Sugar Land, TX); Kalsi, Manmohan Singh (Houston, TX)

2000-03-14T23:59:59.000Z

231

System and method for cooling a superconducting rotary machine  

Science Conference Proceedings (OSTI)

A system for cooling a superconducting rotary machine includes a plurality of sealed siphon tubes disposed in balanced locations around a rotor adjacent to a superconducting coil. Each of the sealed siphon tubes includes a tubular body and a heat transfer medium disposed in the tubular body that undergoes a phase change during operation of the machine to extract heat from the superconducting coil. A siphon heat exchanger is thermally coupled to the siphon tubes for extracting heat from the siphon tubes during operation of the machine.

Ackermann, Robert Adolf (Schenectady, NY); Laskaris, Evangelos Trifon (Schenectady, NY); Huang, Xianrui (Clifton Park, NY); Bray, James William (Niskayuna, NY)

2011-08-09T23:59:59.000Z

232

DEVELOPMENT OF A ROTARY MICROFILTER FOR RADIOACTIVE WASTE APPLICATIONS  

Science Conference Proceedings (OSTI)

The processing rate of Savannah River Site (SRS) high-level waste decontamination processes are limited by the flow rate of the solid-liquid separation. The baseline process, using a 0.1 micron cross-flow filter, produces {approx}0.02 gpm/sq. ft. of filtrate under expected operating conditions. Savannah River National Laboratory (SRNL) demonstrated significantly higher filter flux for actual waste samples using a small-scale rotary filter. With funding from the U. S. Department of Energy Office of Cleanup Technology, SRNL personnel are evaluating and developing the rotary microfilter for radioactive service at SRS. The authors improved the design for the disks and filter unit to make them suitable for high-level radioactive service. They procured two units using the new design, tested them with simulated SRS wastes, and evaluated the operation of the units. Work to date provides the following conclusions and program status: (1) The authors modified the design of the filter disks to remove epoxy and Ryton{reg_sign}. The new design includes welding both stainless steel and ceramic coated stainless steel filter media to a stainless steel support plate. The welded disks were tested in the full-scale unit. They showed good reliability and met filtrate quality requirements. (2) The authors modified the design of the unit, making installation and removal easier. The new design uses a modular, one-piece filter stack that is removed simply by disassembly of a flange on the upper (inlet) side of the filter housing. All seals and rotary unions are contained within the removable stack. (3) While it is extremely difficult to predict the life of the seal, the vendor representative indicates a minimum of one year in present service conditions is reasonable. Changing the seal face material from silicon-carbide to a graphite-impregnated silicon-carbide is expected to double the life of the seal. Replacement of the current seal with an air seal could increase the lifetime to 5 years and is undergoing testing in the current work. (4) The bottom bushing showed wear due to a misalignment during the manufacture of the filter tank. Replacing the graphite bushing with a more wear resistant material such as a carbide material will increase the lifetime of the bushing. This replacement requires a more wear resistant part or coating to prevent excessive wear of the shaft. The authors are currently conducting testing with the more wear resistant bushing. (5) The project team plans to use the rotary microfilter as a filter in advance of an ion exchange process under development for potential deployment in SRS waste tank risers.

Poirier, M; David Herman, D; Samuel Fink, S

2008-02-25T23:59:59.000Z

233

Research for the Crane Boom Length Coefficient Considering the Tower Head Flexibility in Rotary Plane  

Science Conference Proceedings (OSTI)

When the crane boom length in rotary plane is determined, the traditional methods only consider support condition, non-uniform, boom end lateral displacement constraint effect of amplitude dragline and hoist rope tensile forces. Ignoring tower head elastic ... Keywords: Equivalent elastic support method, Rotary plane, Tower head flexibility, Non-conservative loading, Length coefficient

Zhang Guangyun; Lan Peng; Lu Nianli

2011-01-01T23:59:59.000Z

234

Comparison of residence time models for cascading rotary dryers  

SciTech Connect

The predictions of the models of Matchett and Baker (1988), Saeman and Mitchell (1954) and Friedman and Marshall (1949) for the solids residence time in rotary dryers have been compared with both pilot-scale and industrial-scale data. A countercurrent pilot-scale dryer of 0.2m diameter and 2m long has been used with air velocities up to 1.5 m to measure the residence times of sorghum grain. The average discrepancy for the solids residence time between the predictions and the experiments that were carried out in the pilot-scale rotary dryer is {minus}10.4%. Compared with the models of Friedman and Marshall (1949) and Saeman and Mitchell (1954) for the pilot-scale data obtained here, the Matchett and Baker model is more satisfactory for predicting the solids residence time in this pilot-scale dryer. It has also been found that the model of Matchett and Baker describes the industrial data of Saeman and Mitchell (1954) than the correlation of Friedman and Marshall (1949).

Cao, W.F.; Langrish, T.A.G. [Univ. of Sydney, New South Wales (Australia). Dept. of Chemical Engineering

1999-04-01T23:59:59.000Z

235

Wear compensating seal means for rotary piston coal feeder  

SciTech Connect

The present invention is directed to a wear compensating seal arrangement for use in a rotary piston feeder utilized for feeding pulverized coal into a gasifier operating at relatively high pressures and elevated temperatures. The rotary piston feeder has a circular casing with a coal loading opening therein diametrically opposed from a coal discharge and contains a rotatable disoidal rotor having a cylinder in which a reciprocatable piston is disposed. The reciprocation of the piston within the cylinder is provided by a stationary conjugate cam whereby pulverized coal from a coal hopper at atmospheric pressure can be introduced into the cylinder and then discharged therefrom into the high pressure gasifier while maintaining minimal losses of producer gas and the expenditure of minimal energy which would detract from the efficiency of the gasification. The seal arrangement of the present invention is disposed between the rotor and the casing about the coal discharge and prevents the high pressure gases from within the gasifier from escaping between these relatively movable parts during operation of the coal feeder. The seal utilizes a primary seal in contact with the rotor and a secondary seal supporting the primary seal. The primary seal is continuously urged towards the rotor by springs and the high pressure producer gas.

Gencsoy, Hasan T. (Morgantown, WV); Gardner, John F. (Morgantown, WV)

1979-01-01T23:59:59.000Z

236

Development of a Low-Cost Rotary Steerable Drilling System  

DOE Green Energy (OSTI)

The project had the goal to develop and commercialize a low-cost rotary steerable system (LCRSS) capable of operating downhole at conventional pressures and temperatures to reduce operating costs by a minimum of 50% and lost-in-hole charges by at least 50% over the currently offered systems. The LCRSS system developed under this project does reduce operating costs by 55% and lost-in-hole charges by at least 50%. The developed product is not commercializable in its current form. The overall objective was to develop and commercialize a low cost rotary steerable system (LCRSS) capable of operating downhole at conventional pressures and temperatures (20,000 psi/150 C) while reducing the operating costs by 50% and the lost-in-hole charges by 50% over the currently available systems. The proposed reduction in costs were to be realized through the significant reduction in tool complexity, a corresponding increase in tool reliability as expressed in the mean-time between failure (MTBF), and a reduction in the time and costs required to service tools after each field operation. Ultimately, the LCRSS system was to be capable of drilling 7 7/8 in. to 9 5/8 in. borehole diameters. The project was divided into three Phases, of which Phases I & II were previously completed and reported on, and are part of the case file. Therefore, the previously reported information is not repeated herein. Phase III included the fabrication of two field ready prototypes that were to be subjected to a series of drilling tests at GTI Catoosa, DOE RMOTC, and at customer partnering wells, if possible, as appropriate in the timing of the field test objectives to fully exercise all elements of the LCRSS. These tests were conducted in an iterative process based on a performance/reliability improvement cycle with the goal of demonstrating the system met all aspects required for commercial viability. These tests were conducted to achieve continuous runs of 100+ hours with well trajectories that fully exercised the tool's build/turn/drop/hold target capabilities and its higher end ratings for bit weight, torque and rotary speed. The tool teardowns were rigorously analyzed at the conclusion of each field run to assess component wear rates and to fully document any detrimental behavior(s) observed.

Roney Nazarian

2012-01-31T23:59:59.000Z

237

High pressure rotary piston coal feeder for coal gasification applications  

DOE Patents (OSTI)

The subject development is directed to an apparatus for feeding pulverized coal into a coal gasifier operating at relatively high pressures and elevated temperatures. This apparatus is a rotary piston feeder which comprises a circular casing having a coal loading opening therein diametrically opposed from a coal discharge and contains a rotatable discoid rotor having a cylinder in which a reciprocateable piston is disposed. The reciprocation of the piston within the cylinder is provided by a stationary conjugate cam arrangement whereby the pulverized coal from a coal hopper at atmospheric pressure can be introduced into the cylinder cavity and then discharged therefrom into the high-pressure gasifier without the loss of high pressure gases from within the latter.

Gencsoy, Hasan T. (Morgantown, WV)

1977-05-24T23:59:59.000Z

238

Rim for rotary inertial energy storage device and method  

DOE Patents (OSTI)

The present invention is directed to an improved rim or a high-performance rotary inertial energy storage device (flywheel). The improved rim is fabricated from resin impregnated filamentary material which is circumferentially wound in a side-by-side relationship to form a plurality of discretely and sequentially formed concentric layers of filamentary material that are bound together in a resin matrix. The improved rim is provided by prestressing the filamentary material in each successive layer to a prescribed tension loading in accordance with a predetermined schedule during the winding thereof and then curing the resin in each layer prior to forming the next layer for providing a prestress distribution within the rim to effect a self-equilibrating compressive prestress within the windings which counterbalances the transverse or radial tensile stresses generated during rotation of the rim for inhibiting deleterious delamination problems.

Knight, Jr., Charles E. (Knoxville, TN); Pollard, Roy E. (Powell, TN)

1980-01-01T23:59:59.000Z

239

TESTING OF THE SECOND GENERATION SPINTEK ROTARY FILTER -11357  

SciTech Connect

The SpinTek rotary microfilter has been developed under the Department of Energy (DOE) Office of Environmental Management (EM) for the purpose of deployment in radioactive service in the DOE complex. The unit that was fabricated and tested is the second generation of the filter that incorporates recommended improvements from previous testing. The completion of this test satisfied a key milestone for the EM technology development program and technology readiness for deployment by Savannah River Remediation in the Small Column Ion Exchange and Sludge Washing processes at the Savannah River Site (SRS). The Savannah River National Laboratory (SRNL) contracted SpinTek Filtration to fabricate a full scale 25 disk rotary filter and perform a 1000 hour endurance test with a simulated SRS sludge. Over 1500 hours of operation have been completed with the filter. SpinTek Filtration fabricated a prototypic 25 disk rotary filter including updates to manufacturing tolerances, an updated design to the rotary joint, improved cooling to the bottom journal, decreases in disk and filter shaft hydraulic resistances. The filter disks were fabricated with 0.5 {micro} pore size, sintered-metal filter media manufactured by Pall Corporation (M050). After fabrication was complete, the filter passed acceptance tests demonstrating rejection of solids and clean water flux with a 50% improvement over the previous filters. Once the acceptance test was complete, a 1000 hour endurance test was initiated simulating a sludge washing process. The test used a simulated SRS Sludge Batch 6 recipe. The insoluble solids started at 5 wt% and were raised to 10 and 15 wt% insoluble solids to simulate the concentration of a large volume tank. The filter system was automated and set up for 24 hour unattended operation. To facilitate this, process control logic was written to operate the filter. During the development it was demonstrated that the method of starting and stopping the filter can affect the build up of filter cake on the disks and therefore the performance of the filter. The filter performed well with the simulant. Very little drop in production was noticed between the 5 and 10 wt% insoluble solids feed. Increasing to 15 wt% had a more pronounced impact due to the rheology of the feed. Acid cleaning was used to clean the filter disks in-situ and restore filtration rate to almost 90% of the initial clean disk rate. Eighty liters of 0.2 M nitric acid in conjunction with water rinses were used to clean the filter in less than 2 hours. Filter testing was completed after 1000 hours of operation were performed on the final filter assembly configuration. The total run time for the testing was over 1500 hours. At the end of the test, the sludge washing was performed successfully from approximately 5.6 M to less than 1 M sodium.

Herman, D.; Poirier, M.; Fowley, M.; Keefer, M.; Huff, T.

2011-02-02T23:59:59.000Z

240

Modeling and simulation of two-leaf semi-rotary VAWT  

Science Conference Proceedings (OSTI)

In this paper, according to the structural characteristics of two-leaf semi-rotary VAWT (vertical axis wind turbine), the microelement method and the coordinate system rotation method are used to establish the mathematical model of wind turbine and, ...

Qian Zhang; Haifeng Chen; Binbin Wang

2010-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Bias in hard disk drive rotary actuator pivot bearings: measurements and lubrication phenomena  

Science Conference Proceedings (OSTI)

Bias in disk drive rotary actuator bearings exhibits complex behavior related to the history of the actuator movement. This paper investigates the hysteresis component of bias present after seeks. Measurements of bias during full stroke actuator movements ...

Daniel Helmick; William Messner; C. Fred Higgs, III

2007-04-01T23:59:59.000Z

242

Generation of Optimal Unit Distance Codes for Rotary Encoders through Simulated Evolution  

Science Conference Proceedings (OSTI)

An evolutionary algorithm is used to generate unit distance codes for absolute rotary encoders. The target is to obtain a code suitable for disk size reduction, or for resolution increase, thus overcoming the limitations of conventional Gray codes. Obtained ...

Stefano Gregori; Roberto Rossi; Guido Torelli; Valentino Liberali

2001-04-01T23:59:59.000Z

243

GA 200-500 (VSD): Oil-injected rotary screw compressors, 200 ...  

U.S. Energy Information Administration (EIA)

GA 200-500 (VSD): Oil-injected rotary screw compressors, 200-500 kW / 268-670 hp.,Kunshan CompAirs Machinery Plant Co.,Ltd is the leading air ...

244

GA 30+-90 / GA 37-90 VSD: Oil-injected rotary screw ...  

U.S. Energy Information Administration (EIA)

GA 30+-90 / GA 37-90 VSD: Oil-injected rotary screw compressors, 30-90 kW / 40-125 hp,Kunshan CompAirs Machinery Plant Co.,Ltd is the leading air ...

245

GAe11-30 / GAe 18-30 VSD: Oil-injected rotary screw ...  

U.S. Energy Information Administration (EIA)

GAe11-30 / GAe 18-30 VSD: Oil-injected rotary screw compressors, 11-30 kW / 15-40 hp,Kunshan CompAirs Machinery Plant Co.,Ltd is the leading air ...

246

GA 11+-30/GA 15-30 VSD: Oil-injected rotary screw compressors ...  

U.S. Energy Information Administration (EIA)

GA 11+-30/GA 15-30 VSD: Oil-injected rotary screw compressors, 11-30 kW / 15-40 hp,Kunshan CompAirs Machinery Plant Co.,Ltd is the leading air ...

247

GA 90+-160+ / GA 110-160 VSD: Oil-injected rotary screw ...  

U.S. Energy Information Administration (EIA)

GA 90+-160+ / GA 110-160 VSD: Oil-injected rotary screw compressors, 90-160 kW / 125-200 hp.,Kunshan CompAirs Machinery Plant Co.,Ltd is the leading ...

248

Granular Attrition due to Rotary Valve in a Pneumatic Conveying System  

E-Print Network (OSTI)

The rotary valve is a widely used mechanical device in many solids-handling industrial processes. However, it may also be responsible for most of the attrition effects occurring in a typical process. In this study, the ...

Yao, Jun

249

High-potential Working Fluids for Next Generation Binary Cycle...  

NLE Websites -- All DOE Office Websites (Extended Search)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...61 6.3 Heat Exchanger Sizing for the Supercritical NEW FLUID ORC Test Rig. . . . . . . . . . . ....

250

Hydrodynamically Lubricated Rotary Shaft Having Twist Resistant Geometry  

SciTech Connect

A hydrodynamically lubricated squeeze packing type rotary shaft with a cross-sectional geometry suitable for pressurized lubricant retention is provided which, in the preferred embodiment, incorporates a protuberant static sealing interface that, compared to prior art, dramatically improves the exclusionary action of the dynamic sealing interface in low pressure and unpressurized applications by achieving symmetrical deformation of the seal at the static and dynamic sealing interfaces. In abrasive environments, the improved exclusionary action results in a dramatic reduction of seal and shaft wear, compared to prior art, and provides a significant increase in seal life. The invention also increases seal life by making higher levels of initial compression possible, compared to prior art, without compromising hydrodynamic lubrication; this added compression makes the seal more tolerant of compression set, abrasive wear, mechanical misalignment, dynamic runout, and manufacturing tolerances, and also makes hydrodynamic seals with smaller cross-sections more practical. In alternate embodiments, the benefits enumerated above are achieved by cooperative configurations of the seal and the gland which achieve symmetrical deformation of the seal at the static and dynamic sealing interfaces. The seal may also be configured such that predetermined radial compression deforms it to a desired operative configuration, even through symmetrical deformation is lacking.

Dietle, Lannie (Houston, TX); Gobeli, Jeffrey D. (Houston, TX)

1993-07-27T23:59:59.000Z

251

Sway control method and system for rotary cranes  

DOE Patents (OSTI)

Methods and apparatuses for reducing the oscillatory motion of rotary crane payloads during operator-commanded or computer-controlled maneuvers. An Input-shaping filter receives input signals from multiple operator input devices and converts them into output signals readable by the crane controller to dampen the payload tangential and radial sway associated with rotation of the jib. The input signals are characterized by a hub rotation trajectory .gamma.(t), which includes a jib angular acceleration .gamma., a trolley acceleration x, and a load-line length velocity L. The system state variables are characterized by a tangential rotation angle .theta.(t) and a radial rotation angle .phi.(t) of the load-line. The coupled equations of motion governing the filter are non-linear and configuration-dependent. In one embodiment, a filter is provided between the operator and the crane for filtering undesired frequencies from the angular .gamma. and trolley x velocities to suppress payload oscillation. In another embodiment, crane commands are computer generated and controlled to suppress vibration of the payload using a postulated asymmetrical shape for the acceleration profiles of the jib, which profiles are uniquely determined by a set of parameters (including the acceleration pulse amplitude and the duration and coast time between pulses), or a dynamic programming approach.

Robinett, Rush D. (Tijeras, NM); Parker, Gordon G. (Houghton, MI); Feddema, John T. (Albuquerque, NM); Dohrmann, Clark R. (Albuquerque, NM); Petterson, Ben J. (Albuquerque, NM)

1999-01-01T23:59:59.000Z

252

Coal desulfurization in a rotary kiln combustor. Final report, March 15, 1990--July 31, 1991  

Science Conference Proceedings (OSTI)

The purpose of this project was to demonstrate the combustion of coal and coal wastes in a rotary kiln reactor with limestone addition for sulfur control. The rationale for the project was the perception that rotary systems could bring several advantages to combustion of these fuels, and may thus offer an alternative to fluid-bed boilers. Towards this end, an existing wood pyrolysis kiln (the Humphrey Charcoal kiln) was to be suitably refurbished and retrofitted with a specially designed version of a patented air distributor provided by Universal Energy, Inc. (UEI). As the project progressed beyond the initial stages, a number of issues were raised regarding the feasibility and the possible advantages of burning coals in a rotary kiln combustor and, in particular, the suitability of the Humphrey Charcoal kiln as a combustor. Instead, an opportunity arose to conduct combustion tests in the PEDCO Rotary Cascading-Bed Boiler (RCBB) commercial demonstration unit at the North American Rayon CO. (NARCO) in Elizabethton, TN. The tests focused on anthracite culm and had two objectives: (a) determine the feasibility of burning anthracite culms in a rotary kiln boiler and (b) obtain input for any further work involving the Humphrey Charcoal kiln combustor. A number of tests were conducted at the PEDCO unit. The last one was conducted on anthracite culm procured directly from the feed bin of a commercial circulating fluid-bed boiler. The results were disappointing; it was difficult to maintain sustained combustion even when large quantities of supplemental fuel were used. Combustion efficiency was poor, around 60 percent. The results suggest that the rotary kiln boiler, as designed, is ill-suited with respect to low-grade, hard to burn solid fuels, such as anthracite culm. Indeed, data from combustion of bituminous coal in the PEDCO unit suggest that with respect to coal in general, the rotary kiln boiler appears inferior to the circulating fluid bed boiler.

Cobb, J.T. Jr.

1992-09-11T23:59:59.000Z

253

Rotary seal with enhanced lubrication and contaminant flushing  

DOE Patents (OSTI)

A resilient, ring shaped interference-type hydrodynamic rotary seal having waves on the lubricant side which provide increased film thickness and flushing action by creating contact pressure induced angulated restrictions formed by abrupt restrictive diverters. The angulated restrictions are defined by projecting ridges, corners at the trailing edge of the waves, or simply by use of a converging shape at the trailing edge of the waves which is more abrupt than the gently converging hydrodynamic inlet shape at the leading edge of the waves. The abrupt restrictive diverter performs two functions; a restricting function and a diverting function. The angulated restrictions cause a local film thickness restriction which produces a damming effect preventing a portion of the lubricant from leaking out of the dynamic sealing interface at the trailing edge of the wave, and results in a much thicker lubricant film thickness under the waves. This contributes to more film thickness in the remainder of the dynamic sealing interface toward the environment because film thickness tends to decay gradually rather than abruptly due to the relative stiffness of the seal material. Because of the angle of the abrupt restrictive diverter relative to the relative rotation direction, in conjunction with the restriction or damming effect, a strong diverting action is produced which pumps lubricant across the dynamic sealing interface toward the environment. The lubricant diversion is caused by the component of the rotational velocity tangent to the abrupt restrictive diverter. The component of rotational velocity normal to the abrupt restrictive diverter causes a portion of the lubricant film to be pumped past the abrupt restrictive diverter, thereby assuring adequate lubrication thereof.

Dietle, Lannie L. (Sugar Land, TX)

2000-01-01T23:59:59.000Z

254

ROTARY FILTER FINES TESTING FOR SMALL COLUMN ION EXCHANGE  

SciTech Connect

SRNL was requested to quantify the amount of 'fines passage' through the 0.5 micron membranes currently used for the rotary microfilter (RMF). Testing was also completed to determine if there is any additional benefit to utilizing a 0.1 micron filter to reduce the amount of fines that could pass through the filter. Quantifying of the amount of fines that passed through the two sets of membranes that were tested was accomplished by analyzing the filtrate by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) for titanium. Even with preparations to isolate the titanium, all samples returned results of less than the instrument's detection limit of 0.184 mg/L. Test results show that the 0.5 micron filters produced a significantly higher flux while showing a negligible difference in filtrate clarity measured by turbidity. The first targeted deployment of the RMF is with the Small Column Ion Exchange (SCIX) at the Savannah River Site (SRS). SCIX uses crystalline silicotitanate (CST) to sorb cesium to decontaminate a clarified salt solution. The passage of fine particles through the filter membranes in sufficient quantities has the potential to impact the downstream facilities. To determine the amount of fines passage, a contract was established with SpinTek Filtration to operate a 3-disk pilot scale unit with prototypic filter disk and various feeds and two different filter disk membranes. SpinTek evaluated a set of the baseline 0.5 micron filter disks as well as a set of 0.1 micron filter disks to determine the amount of fine particles that would pass the membrane and to determine the flux each set produced. The membrane on both disk sets is manufactured by the Pall Corporation (PMM 050). Each set of disks was run with three feed combinations: prototypically ground CST, CST plus monosodium titanate (MST), and CST, MST, plus Sludge Batch 6 (SB6) simulant. Throughout the testing, samples of the filtrate were collected, measured for turbidity, and sent back to SRNL for analysis to quantify the amount of fines that passed through the membrane. It should be noted that even though ground CST was tested, it will be transferred to the Defense Waste Processing Facility (DWPF) feed tank and is not expected to require filtration.

Herman, D.

2011-08-03T23:59:59.000Z

255

Burning state recognition of rotary kiln using ELMs with heterogeneous features  

Science Conference Proceedings (OSTI)

Image based burning state recognition plays an important role in sintering process control of rotary kiln. Although many efforts on dealing with this problem have been made over the past years, the recognition performance cannot be satisfactory due to ... Keywords: Burning state, ELM, Eigen-flame image, Latent semantic analysis, Multivariate image analysis

Weitao Li; Dianhui Wang; Tianyou Chai

2013-02-01T23:59:59.000Z

256

Radioactive air emissions program notice of construction, rotary mode core-sampling truck and exhauster  

SciTech Connect

Efforts have been ongoing to obtain core samples from the contents of each of the Hanford Site`s 149 single-shell tanks (SSTs). The SSTs contain various amounts and combinations of liquid, sludge, and saltcake. Existing sampling equipment is unable to retrieve samples of hardened waste within established tank safety restrictions (particularly limits on temperature). A new rotary mode core-sampling system has been designed to sample tanks containing hardened wastes. The prominent feature of this new system is the use of a nitrogen gas purge. The nitrogen gas purge will cool the drill bit and prevent cross contamination of different waste layers in the tank. The nitrogen gas purge will also allow more complete sample recovery, by clearing cuttings that might otherwise obstruct the sampler or drill bit. Nitrogen was chosen over other compressed gases for its inherent safety. Many of the tanks to be sampled with the rotary mode core-sampling system are not actively ventilated, these tanks are operated at atmospheric pressure with passive (breather) high-efficiency particulate air (HEPA) filters. Unless a ventilation system of the proper capacity is used, addition of the nitrogen purge gas to SSTs will cause the tanks to pressurize. Additionally, the use of the rotary mode core-sampling system will generate aerosols and dusts potentially containing radioactive particles in the tank vapor space. Consequently, an exhauster will be required during operation of the rotary mode core-sampling system on SSTs to prevent tank pressurization and to control emissions. This exhauster will be required to be moved from tank farm to tank farm with the rotary mode core-sampling system.

Not Available

1993-05-01T23:59:59.000Z

257

Snubdrilling a new well in Venezuela  

Science Conference Proceedings (OSTI)

A new well was successfully drilled using a snubbing jack. The drill bit was rotated using a rotary table, downhole motors and combination of the two. Expected high-pressure zones prompted this use of ``snubdrilling.`` The primary objective was to drill a vertical well through underlying sands and gain information about formation pressures. This data would aid in the drilling of a relief well using a conventional drilling rig. The secondary objective was to relieve pressure by putting this new well on production. In addition to special high-pressure drilling jobs, there are other drilling applications where snubbing jacks are a feasible alternative to conventional rotary drilling rigs or coiled tubing units. Slimhole, underbalanced and flow drilling, and sidetracking of existing wells are excellent applications for snubdrilling. Advantages of snubdrilling vs. coiled tubing drilling, include ability to rotate drillstrings, use high-torque downhole motors, pump at high rates and pressures, apply significant overpull in case of stuck pipe, and run casing and liners without rigging down. Shortcomings of drilling with snubbing jacks compared to coiled tubing are the need to stop circulation while making new connections and inability to run continuous cable inside workstrings.

Aasen, J.

1995-12-01T23:59:59.000Z

258

U. S. Energy Information Administration | Drilling Productivity Report  

U.S. Energy Information Administration (EIA) Indexed Site

December 2013 December 2013 Explanatory notes Drilling Productivity Report The Drilling Productivity Report uses recent data on the total number of drilling rigs in operation along with estimates of drilling productivity and estimated changes in production from existing oil and natural gas wells to provide estimated changes in oil and natural gas production for six key fields. EIA's approach does not distinguish between oil-directed rigs and gas-directed rigs because once a well is completed it may produce both oil and gas; more than half of the wells do that. Monthly additions from one average rig Monthly additions from one average rig represent EIA's estimate of an average rig's

259

Internal combustion engine with rotary valve assembly having variable intake valve timing  

DOE Patents (OSTI)

An internal combustion engine has rotary valves associated with movable shutters operable to vary the closing of intake air/fuel port sections to obtain peak volumetric efficiency over the entire range of speed of the engine. The shutters are moved automatically by a control mechanism that is responsive to the RPM of the engine. A foot-operated lever associated with the control mechanism is also used to move the shutters between their open and closed positions.

Hansen, Craig N. (Eden Prairie, MN); Cross, Paul C. (Shorewood, MN)

1995-01-01T23:59:59.000Z

260

Mathematical model and the dynamic simulation of an electromechanical rotary device. [SLENOID  

SciTech Connect

A mathematical model of an electro-mechanical rotary device is presented. This device contains a rotor, stator, and two spring-loaded arms which restrict the rotor motion. The desired action is the alignment of the rotor and the consequent movement of the arms. The SLENOID computer program for calculating the magnetic torque, air gap permeance, spring torque, damping effects, and motion of the rotor and arms is described. (LCL)

Emergy, J.D.

1980-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Demonstration of a rotary separator for two-phase brine and steam flows. Final report  

DOE Green Energy (OSTI)

The application of a two-phase rotary separator for geothermal energy conversion was demonstrated. Laboratory tests were conducted with clean water and steam at Biphase Energy Systems, Inc., Santa Monica, California. Field tests were conducted at the Union Oil Co., Tow No. 1 wellsite near Brawley, California. The system tested consisted of the major components of a total flow rotary separator/turbine conversion system. A nozzle converted the brine wellhead enthalpy to two-phase flow kinetic by impinging the nozzle flow tangentially on the inside of the separator. The flow was therefore subjected to the high centrifugal force field in the separator. This caused the liquid phase to collect as a film on the separator drum with very little energy loss. The steam was allowed to flow radially inward to the central steam discharge. Potable water was obtained by condensing the steam exhaust. The brine collection system converted the liquid film kinetic energy to static pressure head. The system was operated for 116 hours in a high salinity environment (115,000 ppM TDS). The system operated properly with no adverse effects from solids precipitation or scale buildup. The rotary separator produced separate flows of pure liquid and steam of greater than 99.5% quality.

Cerini, D.J.

1978-01-01T23:59:59.000Z

262

Modeling of the solids transportation within an industrial rotary dryer: A simple model  

SciTech Connect

To better understand the underlying phenomena taking place in an industrial rotary dryer and to determine the optimum operating conditions, a simulator in which the solids transportation, the gas flow, and the heat and mass transfer are modeled is currently being developed. This paper describes the use of interactive perfect mixers in series to model the solids transportation within an industrial rotary dryer, on the basis of an experimental residence time distribution curve (RTD). Two simple models are proposed: a series of perfect well-mixed interacting tanks and a modified Cholette-Cloutier model. The first model is not able to account for the nonideal behavior of the solids transportation in the rotary dryer. To account for the characteristic extended tail of the RTD curves observed in industrial dryers, in a second model, the solid phase is divided between an active and a dead zone. This model, with 36 cells and 25% of the volume occupied by the dead zones, modeled very well the industrial RTD curve. In addition, the model produces bed depth and axial velocity profiles that are consistent with those reported in the literature.

Duchesne, C.; Thibault, J.; Bazin, C. [Laval Univ., Sainte-Foy, Quebec (Canada)] [Laval Univ., Sainte-Foy, Quebec (Canada)

1996-07-01T23:59:59.000Z

263

Identification and Mechanism of Small Molecule Inhibitors of RNA Interference  

E-Print Network (OSTI)

2009). An RIG-I-Like RNA helicase mediates antiviral RNAi2009). An RIG-I-Like RNA helicase mediates antiviral RNAihomolog of Werner syndrome helicase and RNaseD. Cell 99(2):

Elkashef, Samer

2011-01-01T23:59:59.000Z

264

Newsletter 7  

NLE Websites -- All DOE Office Websites (Extended Search)

of rig data to the internet is now possible with live updates on drilling and testing operations. The rig layout is cleaner and safer than ever before with the changes...

265

Microsoft Word - Clemson DTTF FINAL_EA  

NLE Websites -- All DOE Office Websites (Extended Search)

by the U.S. Navy. The facility would consist of two test rigs equipped with independent drive systems. Each test rig would be capable of testing a range of wind turbine...

266

Integrated Status and Effectiveness Monitoring Program - Entiat River Snorkel Surveys and Rotary Screw Trap, 2007.  

DOE Green Energy (OSTI)

The USFWS Mid-Columbia River Fishery Resource Office conducted snorkel surveys at 24 sites during the summer and fall periods of 2006 survey periods as part of the Integrated Status and Effectiveness Monitoring Program in the Entiat River. A total of 37,938 fish from 15 species/genera and an unknown category were enumerated. Chinook salmon were the overall most common fish observed and comprised 15% of fish enumerated followed by rainbow trout (10%) and mountain whitefish (7%). Day surveys were conducted during the summer period 2007 (August), while night surveys were conducted during the fall 2007 (October) surveys. The USFWS Mid-Columbia River Fishery Resource Office (MCFRO) operated two rotary screw traps on the Entiat River as part of the Integrated Status and Effectiveness Monitoring Program (ISEMP) program from August through November of 2007. Along with the smolt traps, juvenile emigrants were also captured at remote locations throughout the Entiat watershed and its major tributary, the Mad River. A total of 999 wild Oncorhynchus mykiss and 5,107 wild run O. tshawytscha were PIT tagged during the study period. Rotary screw trap efficiencies averaged 22.3% for juvenile O. tshawytscha and 9.0% for juvenile O. mykiss. Rotary screw traps operated 7 days a week and remote capture operations were conducted when flow and temperature regimes permitted. This is third annual progress report to Bonneville Power Administration for the snorkel surveys conducted in the Entiat River as related to long-term effectiveness monitoring of restoration programs in this watershed. The objective of this study is to monitor the fish habitat utilization of planned in-stream restoration efforts in the Entiat River by conducting pre- and post-construction snorkel surveys at selected treatment and control sites.

Nelle, R.D.

2008-01-01T23:59:59.000Z

267

Rigger's Handbook  

Science Conference Proceedings (OSTI)

This handbook provides guidance for lifting and rigging at nuclear and fossil power plants. It is intended to increase personnel safety and efficiency during lifting and rigging activities.The handbook describes various types of lifting and rigging equipment, including slings, rigging hardware, lifting devices, hoists, hydraulic jacks, and trolleys. It provides reference data such as calculations of area, volume, and center of gravity, as well as sling tensions, material weights, knots, ...

2013-11-27T23:59:59.000Z

268

I Was Like, Oh My God, Did I Really Say That? IECA Spring ...  

U.S. Energy Information Administration (EIA)

... Subsidies and Demand Not All Opportunities are the Same Electron Imagery of Barnett Fractures US Gas Rigs, ...

269

SCFA lead lab technical assistance review of the Pit 7 Complex source containment  

E-Print Network (OSTI)

be achieved using a remote handling rig, or through use of arequire remote excavation techniques and special handling.

2001-01-01T23:59:59.000Z

270

WA_07_040_GRAFTECH_INTERNATIONAL_LTD_Waiver_of_Patent_Rights...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

40GRAFTECHINTERNATIONALLTDWaiverofPatentRights.pdf WA07040GRAFTECHINTERNATIONALLTDWaiverofPatentRights.pdf WA07040GRAFTECHINTERNATIONALLTDWaiverofPatentRig...

271

WA_04_040_HONEYWELL_INTERNATIONAL_INC_Waiver_of_Patent_Right...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0HONEYWELLINTERNATIONALINCWaiverofPatentRight.pdf WA04040HONEYWELLINTERNATIONALINCWaiverofPatentRight.pdf WA04040HONEYWELLINTERNATIONALINCWaiverofPatentRig...

272

WA_06_033_PARKER_HANNIFIN_CORPORATION_Waiver_of_Patent_Right...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3PARKERHANNIFINCORPORATIONWaiverofPatentRight.pdf WA06033PARKERHANNIFINCORPORATIONWaiverofPatentRight.pdf WA06033PARKERHANNIFINCORPORATIONWaiverofPatentRig...

273

DOE-STD-1090-2011  

Energy.gov (U.S. Department of Energy (DOE))

Hoisting and Rigging (Formerly Hoisting and Rigging Manual) Superseding DOE-STD-1090-2007 (August 2007) The U.S. Department of Energy (DOE) Hoisting and Rigging Standard is intended to be used by supervisors, line managers, safety personnel, equipment operators, riggers and other personnel responsible for the safety of hoisting and rigging operations at DOE sites. It may be used as either contract document or as a best practices guide at the site’s or program office’s discretion.

274

Obtaining pressures in the 10?5 Pa range with oil?sealed rotary vacuum pumps  

Science Conference Proceedings (OSTI)

Trapped oil?sealed rotary pumps are usually considered capable of ultimate pressures no lower than about 10?3 Pa. Experiments are described which confirm that most of this residual gas originates from air dissolved in the pump oil. Replacement of the air with a less soluble gas (helium) or an easily trapped gas (carbon dioxide) is shown to give a useful reduction in ultimate pressure and to reduce the oxygen partial pressure to essentially zero. Operation with completely degassed oil is shown to give ultimate pressures in the 10?5 Pa range. The design of pumps based on these principles is discussed.

B. R. F. Kendall

1982-01-01T23:59:59.000Z

275

On the use of the parabolic concentration profile assumption for a rotary desiccant dehumidifier  

SciTech Connect

The current work describes a model for a desiccant dehumidifier which uses a parabolic concentration profile assumption to model the diffusion resistance inside the desiccant particle. The relative merits of the parabolic concentration profile model compared with widely utilized rotary desiccant wheel models are discussed. The periodic steady-state parabolic concentration profile model developed is efficient and can accommodate a variety of materials. These features make it an excellent tool for design studies requiring repetitive desiccant wheel simulations. A quartic concentration profile assumption was also investigated which yielded a 2.8 percent average improvement in prediction error over the parabolic model.

Chant, E.E. [Univ. of Turabo, Gurabo (Puerto Rico); Jeter, S.M. [Georgia Inst. of Technology, Atlanta, GA (United States). George W. Woodruff School of Mechanical Engineering

1995-02-01T23:59:59.000Z

276

Local entropy generation analysis of a rotary magnetic heat pump regenerator  

SciTech Connect

The rotary magnetic heat pump has attractive thermodynamic performance but it is strongly influenced by the effectiveness of the regenerator. This study uses local entropy generation analysis to evaluate the regenerator design and to suggest design improvements. The results show that performance of the proposed design is dominated by heat transfer related entropy generation. This suggests that enhancement concepts that improve heat transfer should be considered, even if the enhancement causes a significant increase in viscous losses (pressure drop). One enhancement technique, the use of flow disrupters, was evaluated and the results showed that flow disrupters can significantly reduce thermodynamic losses.

Drost, M.K.; White, M.D.

1990-04-01T23:59:59.000Z

277

Experimental studies of heat and mass exchange in parallel-passage rotary desiccant dehumidifiers for solar cooling applications  

DOE Green Energy (OSTI)

This report presents results of work done to experimentally characterize the performance of rotary desiccant dehumidifiers and to develop and validate analytical methods for evaluating their performance in air-conditioning systems. A facility, the Cyclic Test Facility, and a test-and-analysis procedure were developed to evaluate the performance of the rotary dehumidifiers. Experiments were performed to develop a basic understanding of the simultaneous heat- and mass-transfer processes in the dehumidifiers. Two test articles were tested under cyclic operation to characterize their performance. Detailed accounts of the Cyclic Test Facility, its hardware and instrumentation, the two test articles, and data reduction and analysis methods are provided. The data provide an engineering data base for evaluating rotary desiccant dehumidifiers for cooling applications. 46 refs., 26 figs., 3 tabs.

Bharathan, D.; Parsons, J.M.; Maclaine-cross, I.L.

1987-11-01T23:59:59.000Z

278

Becker, K., Malone, M.J., et al., 1998 Proceedings of the Ocean Drilling Program, Initial Reports, Vol. 174B  

E-Print Network (OSTI)

(drill-pipe measurement from rig floor, mbrf): 4457.1 Total depth (drill-pipe measurement from rig floor, mbrf): 4526.6 Distance between rig floor and sea level (m): 11.6 Water depth (drill-pipe measurement Unit II (63.5-69.5 mbsf): Aphyric basalt Principal results: Sixty-four meters of sediment and 0.58 m

279

COMPENDIUM OF COMPLETED TESTING IN SUPPORT OF ROTARY MICROFILTRATION AT SAVANNAH RIVER SITE AND HANFORD  

SciTech Connect

This report presents a chronological summary of previous technology development efforts concerning the rotary microfiltration (RMF) unit from SpinTek{trademark}. Rotary microfiltration has been developed for high radiation application over the last decades as one of the optional filtration techniques for supplemental treatment. Supplemental treatment includes a near- or in-tank solids separation and subsequent cesium removal unit, followed by an immobilization technique; this includes options such as steam reforming, bulk vitrification or cast stone (grout). The main difference between RMF and standard cross flow filtration (CFF) is the disconnection of filtrate flux from feed velocity; i.e., filtrate flux is only dependent on transmembrane pressure, filter fouling and temperature. These efforts have been supported by the U.S. Department of Energy (DOE), Office of Cleanup Technologies since the 1990s by their Environmental Management Program (currently EM-31). In order to appropriately address future testing needs, a compilation of the relevant previous testing reports was essential. This compendium does not intend to cover all of the presentations/reports that were produced over the last decades but focuses on those of relevance for developing an RMF unit fit for deployment at the Hanford site. The report is split into three parts: (1) an introductory overview, (2) Figure 1 graphically covering the main development steps and its key players and (3) a more detailed table of the citations and brief descriptions of results and recommendations.

HUBER HJ

2011-05-24T23:59:59.000Z

280

Baseline Design Compliance Matrix for the Rotary Mode Core Sampling System  

SciTech Connect

The purpose of the design compliance matrix (DCM) is to provide a single-source document of all design requirements associated with the fifteen subsystems that make up the rotary mode core sampling (RMCS) system. It is intended to be the baseline requirement document for the RMCS system and to be used in governing all future design and design verification activities associated with it. This document is the DCM for the RMCS system used on Hanford single-shell radioactive waste storage tanks. This includes the Exhauster System, Rotary Mode Core Sample Trucks, Universal Sampling System, Diesel Generator System, Distribution Trailer, X-Ray Cart System, Breathing Air Compressor, Nitrogen Supply Trailer, Casks and Cask Truck, Service Trailer, Core Sampling Riser Equipment, Core Sampling Support Trucks, Foot Clamp, Ramps and Platforms and Purged Camera System. Excluded items are tools such as light plants and light stands. Other items such as the breather inlet filter are covered by a different design baseline. In this case, the inlet breather filter is covered by the Tank Farms Design Compliance Matrix.

LECHELT, J.A.

2000-10-17T23:59:59.000Z

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Application of PDC bits in the Kuparuk River Field, Alaska  

SciTech Connect

In soft to medium hard clays and shales, PDC bits have proven to be economically successful in the Kuparuk River Field, Alaska. Through the redesign and modification of PDC bits and rig equipment, the necessary operating parameters have been achieved and the use of PDC bits has become routine. These bits are typically run with a standpipe pressure of 4000 psi, pump rate of 400 to 450 gpm, and a rotary speed of 150 to 200 rpm. Using these high operating parameters, a savings of about $50,000 per PDC bit is being achieved when compared to roller cone bits.

Balkenbush, R.J.; Onisko, J.E.

1983-10-01T23:59:59.000Z

282

Comparison of the performance of open cycle air conditioners utilizing rotary desiccant dehumidifiers  

DOE Green Energy (OSTI)

This paper presents the results of an investigation of open cycle cooling systems using rotary desiccant dehumidifiers. Three systems, the ventilation, recirculation, and Dunkle cycles have been modeled. The performance of these systems coupled with an air-based solar system has been determined using TRNSYS simulations of system operation in four representative US climates. The system COP, fraction of the total cooling load met by the desiccant system, and fraction of the thermal energy provided by solar energy are compared. An assessment of the effect of climate and system parameters on the relative performance of the three system configurations is made. It is shown that in order to meet residential loads of 7 to 11 kW with a COP on the order of unity, systems with high effectiveness must be employed. These systems were also found to perform well when operated solely with a solar thermal input.

Jurinak, J.J.; Beckman, W.A.

1985-01-01T23:59:59.000Z

283

Control schemes for an industrial rotary calciner with a heat shield around the combustion zone  

SciTech Connect

Soda ash (sodium carbonate) is produced by calcining natural trona ore (sodium sesquicarbonate) in rotary calciners. Shell overheating, the consequent deformation of the calciner shell, and heat loss are frequently encountered problems during this operation. Installation of a concentric, metallic heat shield around the calciner`s combustion zone can help to reduce the shell temperature and recover some of the energy that would otherwise be lost. Another problem often encountered is the deterioration of product quality when the system inputs deviate from their design rates. A mathematical model of the calciner with a heat shield is used to design different control schemes in order to maintain the product quality. Performance of the designed control schemes is demonstrated via computer simulation.

Ciftci, S.; Kim, N.K. [Michigan Technological Univ., Houghton, MI (United States). Dept. of Chemical Engineering] [Michigan Technological Univ., Houghton, MI (United States). Dept. of Chemical Engineering

1999-03-01T23:59:59.000Z

284

Method and apparatus for maximizing throughput of indirectly heated rotary kilns  

DOE Patents (OSTI)

An apparatus and method for achieving improved throughput capacity of indirectly heated rotary kilns used to produce pyrolysis products such as shale oils or coal oils that are susceptible to decomposition by high kiln wall temperatures is disclosed. High throughput is achieved by firing the kiln such that optimum wall temperatures are maintained beginning at the point where the materials enter the heating section of the kiln and extending to the point where the materials leave the heated section. Multiple high velocity burners are arranged such that combustion products directly impact on the area of the kiln wall covered internally by the solid material being heated. Firing rates for the burners are controlled to maintain optimum wall temperatures.

Coates, Ralph L; Smoot, L. Douglas; Hatfield, Kent E

2012-10-30T23:59:59.000Z

285

An Advanced Solar-Powered Rotary Solid Adsorption Refrigerator with High Performance  

E-Print Network (OSTI)

In this paper, according to practical consideration, a new solar powered rotary solid adsorption refrigerator system adopting activated carbon fibre + ethanol as its adsorption pair has been designed with higher performance. Moreover, the principle of the refrigeration cycle, different components of the machine, selection of working pairs and feasible theory analysis of the refrigeration system all have been presented in detail. In addition, it shows that the new refrigerator has many great advantages including a simple structure, fast refrigeration, higher thermodynamic coefficient, friendly to the atmospheric environment, etc. This paper explains that the refrigerating process is constant, which has a promising potential for competing the 'intermittent' cycle reported before. Through improving the refrigerant performance of heat and mass transfer in the adsorbent bed, the refrigeration cycle has been advanced from the aspect of utilization of the thermal energy from low-temperature level resources. In addition, it is shown that the commercial solar powered refrigerator will be existent in the near future.

Zheng, A.; Gu, J.

2006-01-01T23:59:59.000Z

286

Stable five axes cryogenic photoemission manipulator without a differentially pumped rotary feedthrough  

Science Conference Proceedings (OSTI)

We report on the design and construction of an ultrahigh vacuum compatible cryogenic manipulator for angle resolved photoemission spectroscopy. Unlike designs that have been used so far, our design allows five motions (three translational and two angular) without a differentially pumped rotary feedthrough. The design greatly reduces the sample motion upon rotation, which is crucial in automatic data acquisition over a large area in the momentum space. The constructed manipulator shows smooth motions in vacuum and the lowest temperature it could reach is about 8 K at the sample position. Angular reproducibilities are found to be about 0.02 deg. for both of the angular motions. The wobbling motion from the rotation around the vertical rotation axis is found to be virtually nonexistent (less than 0.1 mm)

Kim, Bum Joon; Kim, Hyeong-Do; Cho, Deok-Yong; Kim, Myongjin; Oh, S.-J.; Kim, Changyoung [School of Physics and Center for Strongly Correlated Materials Research, Seoul National University, Seoul 151-742 (Korea, Republic of); Pohang Accelerator Laboratory, Pohang University of Science and Technology, Pohang 790-784 (Korea, Republic of); School of Physics and Center for Strongly Correlated Materials Research, Seoul National University, Seoul 151-742 (Korea, Republic of); Pohang Accelerator Laboratory, Pohang University of Science and Technology, Pohang 790-784 (Korea, Republic of); School of Physics and Center for Strongly Correlated Materials Research, Seoul National University, Seoul 151-742 (Korea, Republic of); Institute of Physics and Applied Physics, Yonsei University, Seoul 120-749 (Korea, Republic of)

2005-06-15T23:59:59.000Z

287

Unsteady-state material balance model for a continuous rotary dissolver  

Science Conference Proceedings (OSTI)

The unsteady-state continuous rotary dissolver material balance code (USSCRD) is a useful tool with which to study the performance of the rotary dissolver under a wide variety of operating conditions. The code does stepwise continuous material balance calculations around each dissolver stage and the digester tanks. Output from the code consists of plots and tabular information on the stagewise concentration profiles of UO{sub 2}, PuO{sub 2}, fission products, Pu(NO{sub 3}){sub 4}, UO{sub 2}(NO{sub 3}){sub 2}, fission product nitrates, HNO{sub 3}, H{sub 2}O, stainless steel, total particulate, and total fuel in pins. Other information about material transfers, stagewise liquid volume, material inventory, and dissolution performance is also provided. This report describes the development of the code, its limitations, key operating parameters, usage procedures, and the results of the analysis of several sets of operating conditions. Of primary importance in this work was the estimation of the steady-state heavy metal inventory in a 0.5-t/d dissolver drum. Values ranging from {similar_to}12 to >150 kg of U + Pu were obtained for a variety of operating conditions. Realistically, inventories are expected to be near the lower end of this range. Study of the variation of operating parameters showed significant effects on dissolver product composition from intermittent solids feed. Other observations indicated that the cycle times for the digesters and shear feed should be closely coupled in order to avoid potential problems with off-specification product. 19 references, 14 tables.

Lewis, B.E.

1984-09-01T23:59:59.000Z

288

DSP-Based Sensor-less Permanent Magnet Synchronous Motor Driver With Quasi-Sine PWM for Air-Conditioner Rotary Compressor.  

E-Print Network (OSTI)

??This thesis presented a sensor-less permanent magnet synchronous motor (PMSM) driver for controlling air-conditioner rotary compressor speed. In this thesis, a quasi-sine pulse-width modulation (PWM)… (more)

Liu, Li-hsiang

2012-01-01T23:59:59.000Z

289

Deep Drilling Basic Research: Volume 4 - System Description. Final Report, November 1988--August 1990  

DOE Green Energy (OSTI)

The first section of this Volume will discuss the ''Conventional Drilling System''. Today's complex arrangement of numerous interacting systems has slowly evolved from the very simple cable tool rigs used in the late 1800s. Improvements to the conventional drilling rig have varied in size and impact over the years, but the majority of them have been evolutionary modifications. Each individual change or improvement of this type does not have significant impact on drilling efficiency and economics. However, the change is almost certain to succeed, and over time--as the number of evolutionary changes to the system begin to add up--improvements in efficiency and economics can be seen. Some modifications, defined and described in this Volume as Advanced Modifications, have more than just an evolutionary effect on the conventional drilling system. Although the distinction is subtle, there are several examples of incorporated advancements that have had significantly more impact on drilling procedures than would a truly evolutionary improvement. An example of an advanced modification occurred in the late 1970s with the introduction of Polycrystalline Diamond Compact (PDC) drill bits. PDC bits resulted in a fundamental advancement in drilling procedures that could not have been accomplished by an evolutionary improvement in materials metallurgy, for example. The last drilling techniques discussed in this Volume are the ''Novel Drilling Systems''. The extent to which some of these systems have been developed varies from actually being tested in the field, to being no more than a theoretical concept. However, they all have one thing in common--their methods of rock destruction are fundamentally different from conventional drilling techniques. When a novel drilling system is introduced, it is a revolutionary modification of accepted drilling procedures and will completely replace current techniques. The most prominent example of a revolutionary modification in recent history was the complete displacement of cable tool rigs by rotary drilling rigs in the late 1920s.

Anderson, E.E.; Maurer, W.C.; Hood, M.; Cooper, G.; Cook, N.

1990-06-01T23:59:59.000Z

290

Coal desulfurization in a rotary kiln combustor. Quarterly report No. 1, April 16, 1990--July 15, 1990  

Science Conference Proceedings (OSTI)

BCR National Laboratory (BCRNL) has initiated a project aimed at evaluating the technical and economic feasibility of using a rotary kiln, suitably modified, to burn Pennsylvania anthracite wastes, co-fired with high-sulfur bituminous coal. Limestone will be injected into the kiln for sulfur control, to determine whether high sulfur capture levels can be achieved with high sorbent utilization. The principal objectives of this work are: (1) to prove the feasibility of burning anthracite refuse, with co-firing of high-sulfur bituminous coal and with limestone injection for sulfur emissions control, in a rotary kiln fitted with a Universal Energy International (UEI) air injector system; (2) to determine the emissions levels of SO{sub x} and NO{sub x} and specifically to identify the Ca/S ratios that are required to meet New Source Performance Standards; (3) to evaluate the technical and economic merits of a commercial rotary kiln combustor in comparison to fluidized bed combustors; and, (4) to ascertain the need for further work, including additional combustion tests, prior to commercial application, and to recommend accordingly a detailed program towards this end.

Cobb, J.T. Jr.

1990-08-15T23:59:59.000Z

291

Method and system including a double rotary kiln pyrolysis or gasification of waste material  

DOE Patents (OSTI)

A method of destructively distilling an organic material in particulate form wherein the particulates are introduced through an inlet into one end of an inner rotating kiln ganged to and coaxial with an outer rotating kiln. The inner and outer kilns define a cylindrical annular space with the inlet being positioned in registry with the axis of rotation of the ganged kilns. During operation, the temperature of the wall of the inner rotary kiln at the inlet is not less than about 500.degree. C. to heat the particulate material to a temperature in the range of from about 200.degree. C. to about 900.degree. C. in a pyrolyzing atmosphere to reduce the particulate material as it moves from the one end toward the other end. The reduced particulates including char are transferred to the annular space between the inner and the outer rotating kilns near the other end of the inner rotating kiln and moved longitudinally in the annular space from near the other end toward the one end in the presence of oxygen to combust the char at an elevated temperature to produce a waste material including ash. Also, heat is provided which is transferred to the inner kiln. The waste material including ash leaves the outer rotating kiln near the one end and the pyrolysis vapor leaves through the particulate material inlet.

McIntosh, Michael J. (Bolingbrook, IL); Arzoumanidis, Gregory G. (Naperville, IL)

1997-01-01T23:59:59.000Z

292

Method and system including a double rotary kiln pyrolysis or gasification of waste material  

DOE Patents (OSTI)

A method is described for destructively distilling an organic material in particulate form wherein the particulates are introduced through an inlet into one end of an inner rotating kiln ganged to and coaxial with an outer rotating kiln. The inner and outer kilns define a cylindrical annular space with the inlet being positioned in registry with the axis of rotation of the ganged kilns. During operation, the temperature of the wall of the inner rotary kiln at the inlet is not less than about 500 C to heat the particulate material to a temperature in the range of from about 200 C to about 900 C in a pyrolyzing atmosphere to reduce the particulate material as it moves from the one end toward the other end. The reduced particulates including char are transferred to the annular space between the inner and the outer rotating kilns near the other end of the inner rotating kiln and moved longitudinally in the annular space from near the other end toward the one end in the presence of oxygen to combust the char at an elevated temperature to produce a waste material including ash. Also, heat is provided which is transferred to the inner kiln. The waste material including ash leaves the outer rotating kiln near the one end and the pyrolysis vapor leaves through the particulate material inlet. 5 figs.

McIntosh, M.J.; Arzoumanidis, G.G.

1997-09-02T23:59:59.000Z

293

Apparatus and methods for cooling and sealing rotary helical screw compressors  

DOE Patents (OSTI)

In a compression system which incorporates a rotary helical screw compressor, and for any type of gas or refrigerant, the working liquid oil is atomized through nozzles suspended in, and parallel to, the suction gas flow, or alternatively the nozzles are mounted on the suction piping. In either case, the aim is to create positively a homogeneous mixture of oil droplets to maximize the effectiveness of the working liquid oil in improving the isothermal and volumetric efficiencies. The oil stream to be atomized may first be degassed at compressor discharge pressure by heating within a pressure vessel and recovering the energy added by using the outgoing oil stream to heat the incoming oil stream. The stripped gas is typically returned to the compressor discharge flow. In the preferred case, the compressor rotors both contain a hollow cavity through which working liquid oil is injected into channels along the edges of the rotors, thereby forming a continuous and positive seal between the rotor edges and the compressor casing. In the alternative method, working liquid oil is injected either in the same direction as the rotor rotation or counter to rotor rotation through channels in the compressor casing which are tangential to the rotor edges and parallel to the rotor center lines or alternatively the channel paths coincide with the helical path of the rotor edges. 14 figs.

Fresco, A.N.

1997-08-05T23:59:59.000Z

294

Apparatus and methods for cooling and sealing rotary helical screw compressors  

DOE Patents (OSTI)

In a compression system which incorporates a rotary helical screw compressor, and for any type of gas or refrigerant, the working liquid oil is atomized through nozzles suspended in, and parallel to, the suction gas flow, or alternatively the nozzles are mounted on the suction piping. In either case, the aim is to create positively a homogeneous mixture of oil droplets to maximize the effectiveness of the working liquid oil in improving the isothermal and volumetric efficiencies. The oil stream to be atomized may first be degassed at compressor discharge pressure by heating within a pressure vessel and recovering the energy added by using the outgoing oil stream to heat the incoming oil stream. The stripped gas is typically returned to the compressor discharge flow. In the preferred case, the compressor rotors both contain a hollow cavity through which working liquid oil is injected into channels along the edges of the rotors, thereby forming a continuous and positive seal between the rotor edges and the compressor casing. In the alternative method, working liquid oil is injected either in the same direction as the rotor rotation or counter to rotor rotation through channels in the compressor casing which are tangential to the rotor edges and parallel to the rotor centerlines or alternatively the channel paths coincide with the helical path of the rotor edges.

Fresco, Anthony N. (P.O. Box 734, Upton, NY 11973)

1997-01-01T23:59:59.000Z

295

Independent one-way acting hydraulic jar sections for a rotary drill string  

SciTech Connect

First and second separate one-way acting hydraulic jar sections each include inner and outer telescopically arranged tubular members with means for connecting one end of each the inner and outer tubular members of each jar section in the drill string. Spaced seal means between the inner and outer tubular members form a chamber in each jar section for confining hydraulic operating fluid. Hydraulic jar means are formed by cooperating means on the inner and outer tubular members within each operating fluid chamber. The cooperating means is spaced axially and disengaged in each fluid chamber when the drill string is in tension and compression during rotary drilling operation to inhibit damage and wear thereto. The hydraulic jar means in the first jar section is constructed to deliver an up jar and the jar means in the separate second jar section is constructed to deliver a down jar to the drill string. Drive means in a sealed chamber in each jar section connect the inner and outer tubular members of each jar section to allow relative longitudinal movement while preventing relative rotation therebetween. Means to equalize pressure adjacent one end of each of the chambers with the pressure in the well bore is provided in each jar section, which accommodates relative longitudinal movement of the inner and outer tubular members of each jar section for selectively creating an up or down jarring force independently of the well bore pressure.

Anderson, E.A.; Webb, D.D.

1980-10-07T23:59:59.000Z

296

A method and system including a double rotary kiln pyrolysis or gasification of waste material  

DOE Patents (OSTI)

A method is described for destructively distilling an organic material in particulate form wherein the particulates are introduced through an inlet into one end of an inner rotating kiln ganged to and coaxial with an outer rotating kiln. The inner and outer kilns define a cylindrical annular space with the inlet being positioned in registry with the axis of rotation of the ganged kilns. During operation, the temperature of the wall of the inner rotary kiln at the inlet is not less than about 500 C to heat the particulate material to a temperature in the range of from about 200 C to about 900 C in a pyrolyzing atmosphere to reduce the particulate material as it moves from the one end toward the other end. The reduced particulates including char are transferred to the annular space between the inner and the outer rotating kilns near the other end of the inner rotating kiln and moved longitudinally in the annular space from near the other end toward the one end in the presence of oxygen to combust the char at an elevated temperature to produce a waste material including ash. Also, heat is provided which is transferred to the inner kiln. The waste material including ash leaves the outer rotating kiln near the one end and the pyrolysis vapor leaves through the particulate material inlet.

McIntosh, M.J.; Arzoumanidis, G.G.

1995-12-31T23:59:59.000Z

297

EVALUATION OF ALTERNATIVE FILTER MEDIA FOR THE ROTARY MICROFILTER, PHASE 2  

SciTech Connect

Testing was conducted at the Savannah River National Laboratory (SRNL) to investigate filter membrane performance in an effort to increase rotary microfilter (RMF) throughput. Membranes were tested in the SpinTek Filtration, Inc. Static Test Cell (STC), which permitted quick and easy testing of several different membranes. Testing consisted of 100 hours tests with two different slurry feeds, based on recommendations from the phase 1 testing. One feed contained Monosodium Titanate (MST) solids in a simulated salt solution. The other feed contained simulated sludge batch 6 (SB6) solids in a simulated salt solution. Five membranes were tested, one each from filter manufactures Pall and Porvair and three from the Oak Ridge National Laboratory (ORNL). The membrane from Pall is the current membrane used on the latest generation RMF. The Porvair membrane performed well in previous STC tests as well as one of the ORNL membranes. The other two membranes from ORNL were recently developed and not available for the previous STC test. The results indicate that the Porvair filter performed best with the MST slurry and the ORNL SVB6-1B filter performed best with the SB6 slurry. Difficulty was encountered with the ORNL filters due to their dimensional thickness, which was greater than the recommended filter thickness for the STC. The STC equipment was modified to complete the testing of the ORNL filters.

Fowley, M.

2012-07-31T23:59:59.000Z

298

Performance investigation on a novel two-stage solar driven rotary desiccant cooling system using composite desiccant materials  

Science Conference Proceedings (OSTI)

In this study, a two-stage solar driven rotary desiccant cooling (TSRDC) system with novel configuration and newly developed silica gel-haloid composite desiccant is proposed aiming to reduce regeneration temperature and to achieve high energy performance. Simulated results show that there also exists an optimal rotation speed for TSRDC system. Compared with one-stage system, it is found that for the similar supply air state, the required regeneration temperature of TSRDC system is lower and for the same regeneration temperature, the cooling capacity of TSRDC is bigger. (author)

Ge, T.S.; Li, Y.; Dai, Y.J.; Wang, R.Z. [Institute of Refrigeration and Cryogenics, Shanghai Jiao Tong University, Shanghai 200240 (China)

2010-02-15T23:59:59.000Z

299

Analysis of the Energy-Saving Potential of a Three-Rotary Wheel Fresh Air-Handling Unit  

E-Print Network (OSTI)

To evaluate the energy-saving potential of a proposed three-rotary wheel fresh air-handling unit (TRWFAHU), it is numerically simulated with weather data of Changsha by using a mathematical model. Compared with a conventional fresh air-handling unit, TRWFAHU can save 10.2% of primary energy and greatly decrease the energy consumption of chiller. If waste heat is available for regenerating the desiccant, the system can achieve greater energy savings. It is feasible to improve indoor air quality (IAQ) by increasing ventilation while without increasing energy consumption.

Hao, X.; Zhang, G.; Zou, S.; Liu, H.

2006-01-01T23:59:59.000Z

300

EVALUATION OF SUPPLEMENTAL PRE-TREATMENT DEVELOPMENT REQUIREMENTS TO MEET TRL 6 ROTARY MICROFILTRATION  

SciTech Connect

In spring 2011, the Technology Maturation Plan (TMP) for the Supplemental Treatment Project (RPP-PLAN-49827, Rev. 0), Technology Maturation Plan for the Treatment Project (T4S01) was developed. This plan contains all identified actions required to reach technical maturity for a field-deployable waste feed pretreatment system. The supplemental pretreatment system has a filtration and a Cs-removal component. Subsequent to issuance of the TMP, rotary microfiltration (RMF) has been identified as the prime filtration technology for this application. The prime Cs-removal technology is small column ion exchange (ScIX) using spherical resorcinol formaldehyde (sRF) as the exchange resin. During fiscal year 2011 (FY2011) some of the tasks identified in the TMP have been completed. As of September 2011, the conceptual design package has been submitted to DOE as part of the critical decision (CD-1) process. This document describes the remaining tasks identified in the TMP to reach technical maturity and evaluates the validity of the proposed tests to fill the gaps as previously identified in the TMP. The potential vulnerabilities are presented and the completed list of criteria for the DOE guide DOE G 413.3-4 different technology readiness levels are added in an attachment. This evaluation has been conducted from a technology development perspective - all programmatic and manufacturing aspects were excluded from this exercise. Compliance with the DOE G 413.3-4 programmatic and manufacturing requirements will be addressed directly by the Treatment Project during the course of engineering design. The results of this evaluation show that completion of the proposed development tasks in the TMP are sufficient to reach TRL 6 from a technological point of view. The tasks involve actual waste tests using the current baseline configuration (2nd generation disks, 40 psi differential pressure, 30 C feed temperature) and three different simulants - the PEP, an AP-Farm and an S-saltcake. Based on FY2011 dollars used in the TMP, these tests will have ROM costs of $950K and require up to 10 months to complete. Completion of the simulant testing will satisfy the TRL 5 and TRL 6 criteria that are related to system testing with materials that represent the full range of properties in a relevant environment.

HUBER HJ

2011-10-03T23:59:59.000Z

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Integrated Status and Effectiveness Monitoring Program - Entiat River Rotary Screw Traps,Snorkel Surveys, and Steelhead Redd Surveys, 2008.  

DOE Green Energy (OSTI)

The USFWS Mid-Columbia River Fishery Resource Office (MCRFRO) operated two rotary screw traps on the Entiat River as part of the Integrated Status and Effectiveness Monitoring Program from March through November of 2008. Along with the smolt traps, juvenile emigrants were also captured at remote locations throughout the Entiat watershed and its major tributary, the Mad River. A total of 16,782 wild salmonids were PIT tagged during the study period. Of this, 3,961(23.6%) were wild Oncorhynchus mykiss, 6,987 (41.6%) were wild spring run O. tshawytscha, and 5,591 (33.3%) were identified as wild O. tshawytscha of unknown run. Rotary screw trap efficiencies averaged 40.3% at the upper (Rkm 11.0) trap and 7.8% for the lower (Rkm 2.0) trap. These efficiencies were pooled for emigrant O. tshawytscha and O. mykiss. The MCRFRO conducted effectiveness monitoring snorkel surveys at 24 sites during the winter period and 30 sites during the summer and fall periods of 2008 as part of the Integrated Status and Effectiveness Monitoring Program in the Entiat River. The 2008 steelhead spawning grounds surveys were conducted weekly in the main Entiat River from rkm 1.1 to 44.2. A total of 222 steelhead redds were identified over the period from February 28 to June 16 2008 with April being the peak spawning month. Approximately 80% of the steelhead redds were located downstream of the rkm 26.

Nelle, R.D.; Desgroseiller, Tom; Cotter, Michael (U.S. Fish and Wildlife Service)

2009-02-17T23:59:59.000Z

302

Integrated Status and Effectiveness Monitoring Program - Entiat River Rotary Screw Traps, Snorkel Surveys, and Steelhead Redd Surveys, 2008-2009.  

DOE Green Energy (OSTI)

The USFWS Mid-Columbia River Fishery Resource Office (MCRFRO) operated two rotary screw traps on the Entiat River as part of the Integrated Status and Effectiveness Monitoring Program from March through November of 2008. Along with the smolt traps, juvenile emigrants were also captured at remote locations throughout the Entiat watershed and its major tributary, the Mad River. A total of 16,782 wild salmonids were PIT tagged during the study period. Of this, 3,961(23.6%) were wild Oncorhynchus mykiss, 6,987 (41.6%) were wild spring run O. tshawytscha, and 5,591 (33.3%) were identified as wild O. tshawytscha of unknown run. Rotary screw trap efficiencies averaged 40.3% at the upper (Rkm 11.0) trap and 7.8% for the lower (Rkm 2.0) trap. These efficiencies were pooled for emigrant O. tshawytscha and O. mykiss. The MCRFRO conducted effectiveness monitoring snorkel surveys at 24 sites during the winter period and 30 sites during the summer and fall periods of 2008 as part of the Integrated Status and Effectiveness Monitoring Program in the Entiat River. The 2008 steelhead spawning grounds surveys were conducted weekly in the main Entiat River from rkm 1.1 to 44.2. A total of 222 steelhead redds were identified over the period from February 28 to June 16 2008 with April being the peak spawning month. Approximately 80% of the steelhead redds were located downstream of the rkm 26.

Nelle, R.D.; Desgroseillier, Tom; Cotter, Michael [U.S. Fish and Wildlife Service

2009-04-14T23:59:59.000Z

303

DOE-STD-1090-2004 | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 DOE-STD-1090-2004 June 01, 2004 Hoisting and Rigging Standard The U.S. Department of Energy (DOE) Hoisting and Rigging Standard is intended as a reference document to be used by supervisors, line managers, safety personnel, equipment operators, and any other personnel responsible for safety of hoisting and rigging operations at DOE sites. The standard quotes verbatim or paraphrases (with minor editorial changes for consistency) the requirements of the U.S. Occupational Safety and Health Administration (OSHA) and the American National Standards Institute (ANSI). DOE-STD-1090-2004, Hoisting and Rigging Standard; Cover DOE-STD-1090-2004, Hoisting and Rigging Standard; Table of Contents & Front Matter DOE-STD-1090-2004, Hoisting and Rigging Standard; Chapter 1 Terminology and

304

DOE-STD-1090-2007 | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7 7 DOE-STD-1090-2007 August 29, 2007 Hoisting and Rigging Standard Replaced by DOE-STD-1090-2011 The reissued June 1995 edition marked a change in classification. The DOE Office of Scientific and Technical Information (OSTI) reclassified the manual as a handbook and it was issued as DOE Hoisting and Rigging Handbook (DOE-HDBK-1090-95). After further review, OSTI has reclassified the handbook as a DOE Technical Standard and the September 1996 edition was issued as DOE STANDARD HOISTING AND RIGGING (Formerly Hoisting and Rigging Manual) DOE-STD-1090-96 (Rev-1). Additional revisions issued are DOE-STD-1090-99, DOE-STD-1090-2001, DOE-STD-1090- 2004, and DOE-STD-1090-2007. DOE-STD-1090-2007, Hoisting and Rigging Standard; Cover DOE-STD-1090-2007, Hoisting and Rigging Standard; CN Table

305

Idled MODUs require detailed inspection  

Science Conference Proceedings (OSTI)

When drilling contracts first began to disappear, many contractors prepared rigs for what they believed would be a short-term inactive situation. This article reports that following the utilization rate's plunge, it has become apparent that for many units, the stacked mode is to be a long-term affair. The quality of maintenance performed on a stacked drilling rig is critical to the future of the rig, and in some cases, the contractor who owns it. The most important variable involved in adequately maintaining a rig is the number of skilled personnel to operate and care for the equipment on a regular basis. Due to the prohibitive cost of keeping an idle rig manned, many rigs are going without proper care. A drilling contractor's decision, especially if he is financially over-extended, to refrain from performing vital maintenance is often made with short-term corporate survival in mind.

Johnson, A.

1986-11-01T23:59:59.000Z

306

Slim holes haul in savings  

SciTech Connect

This article reports that during 1986 BP Exploration Company Ltd. successfully drilled six UK land wells with a Microdrill MD-3 ultra-slimhole drilling rig. The objective of the program was to evaluate the slimhole drilling technique, from both a technical and cost-effective viewpoint. Earlier studies indicated up to 30 percent savings in well costs compared to conventionally drilled UK land wells. The technology of drilling slim holes with small rigs is not new. For many years the mineral exploration industry has used small drilling and coring rigs. However, these rigs are not normally equipped with pressure control equipment, oilfield mud and cementing systems or the ability to run complex logs or production test. More recently, the oil industry has made efforts to adapt these rigs to slimhole oil and gas exploration, notably in Australia and Canada. The Microdrill MD-3 rig is a product of this evolution.

Floyd, K.

1987-07-01T23:59:59.000Z

307

EVALUATION OF AP-FARM SIMULANT COMPOSITION FOR ROTARY MICROFILTER TESTING  

SciTech Connect

This document identifies the feed composition of a Hanford AP tank farm simulant for rotary microfiltration testing. The composition is based on an Hanford Tank Waste Operations Simulator (HTWOS) model run in combination with Tank Waste Information Network (TWINS) data and mineralogical studies of actual waste solids. The feed simulant is intended to be used in test runs at SRNL. The simulant will be prepared in two parts: (1) A supernate, composed of water-soluble salts and (2) The undissolved (actually, undissolvable) solids. Test slurries with distinct solids concentrations (e.g., 0.5, 5 and 10 wt%) are then prepared as needed. The base for the composition of supernate and solids is the modeled feed sequence for a deployment scenario of the Supplemental Pretreatment units within AP-farm. These units comprise a filtration part, the RMF, and a Cesium-removal part, a Small Column Ion Exchange. The primary use of this simulant is for filtration testing - however, in case that it is also used for ion-exchange tests, the amount of Cs-137 that would need to be added is available in Table 1 and Attachment 3. A modified model run (MMR-049) of the Hanford Tank Waste Operations Simulator (HTWOS) system plan 6 case 3 was performed to identify the feed sequence. Case 3 assumed supplemental treatment besides the low activity waste (LAW) melter with supplemental pretreatment supporting the pretreatment facility. The MMR did not cap the duration of supplemental pretreatment to 15 months, but rather used it throughout the entire treatment mission as an add-on option to the pretreatment facility at the Waste Treatment and Immobilization Plant (WTP). Tank 241-AP-105 (AP-105) was chosen as the feed tank to the filtration unit. Other parameters included a fixed minimum of 0.5 wt% solids in the feed and a maximum Na-concentration of 5M in the supernate. The solids rejection from the filtration unit was set to 99.99% and the maximum allowed amount of solids within tank AP-105 was set to 10 wt%. A comprehensive description of the run and the full suite of results were issued as SVF-2364-00. The list of individual feed events including the amounts of liquid and solids transferred for the first five years is added as Attachment 2; the chemical composition of the supernate feed comprises Attachment 3. For the simulant composition, only the first five years of proposed feed delivery were taken into account. The main outcome of MMR-049 was that for the first five years, the feed would come mostly from AP-farms. Multiple delivery campaigns to AP-105 are included in this average feed, while minimizing the amount of contributing tanks to the solids in the feed mix.

HUBER HJ

2011-09-19T23:59:59.000Z

308

Drilling in the Rockies  

Science Conference Proceedings (OSTI)

Despite rugged drilling conditions and high drilling costs, rig employment and drilling operations in the Rocky Mountain region of the Overthrust Belt have increased significantly since 1979. Rate of rig employment, well depths, and number of operating companies and contractors in the area are reported. By October 1980, more than 500 active rigs were working in the region, 30% more than were working during the entirety of 1979. (3 photos)

Peacock, D.

1980-12-01T23:59:59.000Z

309

Evaluation of rotary drum screens used to protect juvenile salmonids in the Yakima River Basin, Washington, USA  

DOE Green Energy (OSTI)

The purpose of this study is to assess the design and operation of rotary drum screens. Chinook salmon Oncorhynchus tshawytscha and steelhead O. mykiss are the potentially affected fish. Cold-branded fish are released upstream of the screen facilities. For descaling tests, the fish are captured as they exit the facility and are examined for injuries, descaling, and post-test mortalities. For screen passage tests, nets are placed in the irrigation ditch, downstream of the screen facilities, to determine if fish can pass through or over the screens. More than 100 tests have been conducted with almost 35,000 fish. Additionally, nearly 2000 native fish have been evaluated. Usually less than 2% of the test fish are injured or dead, and the condition of test fish does not differ from the controls. Less than 2% of the fish pass through or over the screens when the screen seals are properly installed and maintained.

Neitzel, D.A.; Abernethy, C.S. (Pacific Northwest Lab., Richland, WA (USA)); Clune, T.J. (USDOE Bonneville Power Administration, Yakima, WA (USA))

1990-10-01T23:59:59.000Z

310

Computational Fluid (introduction)  

E-Print Network (OSTI)

. Construction Flow vectors and pressure distribution on an offshore oil rig Flow around cooling towers Wing-Body Interaction Hypersonic Launch Vehicle Aerodynamics Engine Cooling Polymerization reactor

311

Today in Energy - U.S. Energy Information Administration (EIA)  

U.S. Energy Information Administration (EIA)

New England and New York have largest natural gas price increases in 2013. ... Pad drilling and rig mobility lead to more efficient drilling. ...

312

Today in Energy - U.S. Energy Information Administration (EIA)  

U.S. Energy Information Administration (EIA)

North Dakota oil production reaches new high in 2012, ... Pad drilling and rig mobility lead to more efficient drilling. August 15, ...

313

Today in Energy - Archive - U.S. Energy Information ...  

U.S. Energy Information Administration (EIA)

What's New? Press Room ... Pad drilling and rig mobility lead to more efficient drilling. September 10, 2012 Energy-related carbon dioxide emissions ...

314

Requirements for boom lift operations is to tether an adjustable...  

NLE Websites -- All DOE Office Websites (Extended Search)

system. However, the system must be rigged to prevent the employee from falling. Noah Connell, Acting Director Directorate of Construction 1 As of January 1, 1998, 29 CFR...

315

Inlet distortion generation for a transonic compressor .  

E-Print Network (OSTI)

??A single-stage transonic research compressor and test rig are to be used to obtain data on the effect of inlet flow distortion on compressor (and… (more)

Papamarkos, Ioannis.

2004-01-01T23:59:59.000Z

316

Transaction # 1 ...  

Science Conference Proceedings (OSTI)

... profitability after heavy losses from w eather and from other disasters such as the 1988 Piper Alpha oil rig explosi on and the Exxon Valdez oil spill ...

1999-10-22T23:59:59.000Z

317

Slide 1  

NLE Websites -- All DOE Office Websites (Extended Search)

Fabrication Bob Johnston Hoisting and Rigging Jerry Arnwine Doug Childers Manufacturing Engineers Surveillance Mark Lower Welding Dan Mobley Design-Engineers Donald Searle...

318

RMOTC - Library - Fact Sheets  

NLE Websites -- All DOE Office Websites (Extended Search)

Inventory On-site equipment includes forklifts, backhoes, and workover rigs. Geothermal Enhanced Geothermal System (EGS) and low-temperature testing. Flow Assurance Test...

319

ATP Workbook B&W  

Science Conference Proceedings (OSTI)

... what products the company produces—gas fired-boilers ... of Publications and Broadcast Media US Industrial Outlook ... military, and workers on oil rigs. ...

2010-07-27T23:59:59.000Z

320

TREC 2002 Video Track Runs (cont.)  

Science Conference Proceedings (OSTI)

... examples); 87 - Find shots of oil fields, rigs, derricks, oil drilling/pumping equipment. Shots just of refineries are not desired. (1 video example); 88 ...

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


322

Design and testing of a combustor for a turbo-ramjet for UAV and missile applications .  

E-Print Network (OSTI)

??An existing freejet facility was upgraded and its range of operation extended into the high subsonic regime for operation as a test rig for the… (more)

Piper, Ross H.

2003-01-01T23:59:59.000Z

323

Oak Ridge: Approaching 4 Million Safe Work Hours | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

can safely complete their tasks Mike Tidwell performs a leak check and inspection on propane tanks Inspections ensure hoisting and rigging equipment performs correctly so...

324

EIA Energy Kids - Field Trips  

U.S. Energy Information Administration (EIA)

Agricultural Research Center » Alcoa Aluminum » Anadarko Drilling Rig » Baltimore RESCO Waste-to-Energy Plant » Cape Cod Wind Turbine » Carson Refinery»

325

Manufacturing Composite Structures  

Science Conference Proceedings (OSTI)

... costs of cars, bridges, offshore oil rigs, and ... that capability in place new annual markets in ... adapt those processes for commercial-scale production. ...

2011-10-19T23:59:59.000Z

326

2003  

E-Print Network (OSTI)

Lot Sizing with Inventory Bounds and Fixed Costs: Polyhedral Study and Computation Alper Atamturk ... Scheduling Workover Rigs for Onshore Oil Production

327

GRASP 1. Introduction Metaheuristics are general high-level ...  

E-Print Network (OSTI)

May 28, 2008 ... costs. The element to be incorporated into the partial solution is randomly selected ...... Scheduling workover rigs for onshore oil production.

328

Microsoft Word - Q4 2011 DOE Report 31 Jan 12 FINAL.doc  

NLE Websites -- All DOE Office Websites (Extended Search)

range from site rig up and well preparation, through perforating, injection, and flowback, and to permanent abandonment. Procedures also include sand screen installation,...

329

Enhanced Chemical Cleaning (ECC) Oxalate Destruction Testing  

• Physical limitations of hot cells limit scope of Real Waste testing. • Expected Treatment Tank corrosion does not use the HazSim Rig. Performed by ...

330

NETL: EPAct2005 - Title 9, Subtitle J of the Energy Policy Act...  

NLE Websites -- All DOE Office Websites (Extended Search)

Resources Program image showing a drilling rig at sunset The Ultra-Deepwater and Unconventional Natural Gas and Other Petroleum Resources Program is a 10-year, 50...

331

EERE: Vehicles  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Technologies Office and initiatives, using efficient vehicles, and access vehicle and fuel information. Photo of a ethanol and biodiesel fueling station Photo of three big-rig...

332

Global Internet Summit  

Science Conference Proceedings (OSTI)

... from laboring as a roughneck on drilling rigs to working as an engineer and manager, and running a multi-billion dollar oil and gas company at 33 ...

2010-10-05T23:59:59.000Z

333

Date","Time if available","Events -- Flow Conditions","Collection  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

-- Flow Conditions","Collection" "applicationvnd.ms-excel",,"Explosion and fire; oil and gas flow up riser to ocean surface","None" "applicationvnd.ms-excel",,"Rig sinks;...

334

A study into the permeability and compressibility of Australian bagasse pulp.  

E-Print Network (OSTI)

??This is an experimental study into the permeability and compressibility properties of bagasse pulp pads. Three experimental rigs were custom-built for this project. The experimental… (more)

Rainey, Thomas James

2009-01-01T23:59:59.000Z

335

Kick circulation analysis for extended reach and horizontal wells.  

E-Print Network (OSTI)

??Well control is of the utmost importance during drilling operations. Numerous well control incidents occur on land and offshore rigs. The consequences of a loss… (more)

Long, Maximilian Mark

2005-01-01T23:59:59.000Z

336

Illinois | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Batteries and Energy Storage Hub is a coordinated effort designed to push the limits on battery advances. November 20, 2012 Schlumberger technicians and rig crew lowering...

337

Well servicing market report: Positive signs emerge  

Science Conference Proceedings (OSTI)

Domestic well servicing contractors head into 1988 with an improved outlook. But contractors will hasten to tell you this is not say they are now in a healthy industry with a strong demand for equipment and services. John Copeland, executive vice president of the Association of Oilwell Servicing Contractors (AOSC), says he sees encouragement mainly for two reasons: some producing companies have indicated a willingness to raise rig rates, and significant rig utilization gains were noted in the last quarter of 1987. For now, though, the big negatives are still haunting the industry. These are most often noted as inadequate prices for rigs and by far too many rigs chasing too few jobs.

Peacock, D.

1988-01-01T23:59:59.000Z

338

Assessment of Eagle Ford Shale Oil and Gas Resources.  

E-Print Network (OSTI)

??The Eagle Ford play in south Texas is currently one of the hottest plays in the United States. In 2012, the average Eagle Ford rig… (more)

Gong, Xinglai

2013-01-01T23:59:59.000Z

339

Natural Gas Productive Capacity for the Lower-48 States 1985...  

U.S. Energy Information Administration (EIA) Indexed Site

Administration, Office of Oil and Gas; and IHS Energy. Well Completions Forecast: Energy Information Administration, Office of Oil and Gas, Drilling Rig Model; and Model...

340

UPF-Related Forms | Y-12 National Security Complex  

NLE Websites -- All DOE Office Websites (Extended Search)

Inspection Record PDF CFN-1146 UPF Equipment Operator Qualification Record PDF CFN-1147 Hoisting & Rigging Hardware PDF CFN-1148 Alloy Steel Chain Sling - Periodic Inspection PDF...

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Sales of Fuel Oil and Kerosene in 2009 - U.S. Energy ...  

U.S. Energy Information Administration (EIA)

Crop Production 2009 Summary, January 2010, page 76. Energy Information Administration Fuel Oil and Kerosene Sales 2009 vii drilling rigs in operation, an important ...

342

NETL: Turbine Projects - Efficiency Improvement  

NLE Websites -- All DOE Office Websites (Extended Search)

Efficiency Improvemenet Turbine Projects Efficiency Improvemenet Advanced Hot Section Materials and Coatings Test Rig DataFact Sheets System Study for Improved Gas Turbine...

343

Rockwell Automation  

Science Conference Proceedings (OSTI)

... All rights reserved. Page 62. Areas where Ex equipment are used • Automotive refueling stations or petrol stations • Oil refineries, rigs and ...

344

Effect of Microstructure and Grain Size on Fatigue Properties of ...  

Science Conference Proceedings (OSTI)

Abstract Scope, Passive metals exposed to fatigue and wear in corrosive ... In order to investigate multi-degradation, an in-house developed lab scale test rig ...

345

SERI Desiccant Cooling Test Facility. Status report. Preliminary data on the performance of a rotary parallel-passage silica-gel dehumidifier  

DOE Green Energy (OSTI)

This report describes the SERI Desiccant Cooling Test Facility. The facility can test bench-scale rotary dehumidifiers over a wide range of controlled conditions. We constructed and installed in the test loop a prototype parallel-passage rotary dehumidifier that has spirally wound polyester tape coated with silica gel. The initial tests gave satisfactory results indicating that approximately 90% of the silica gel was active and the overall Lewis number of the wheel was near unity. The facility has several minor difficulties including an inability to control humidity satisfactorily and nonuniform and highly turbulent inlet velocities. To completely validate the facility requires a range of dehumidifier designs. Several choices are available including constructing a second parallel-passage dehumidifier with the passage spacing more uniform.

Schultz, K.J.

1986-04-01T23:59:59.000Z

346

Apparatus and method for controlling the rotary airlocks in a coal processing system by reversing the motor current rotating the air lock  

SciTech Connect

An improvement to a coal processing system where hard materials found in the coal may cause jamming of either inflow or outflow rotary airlocks, each driven by a reversible motor. The instantaneous current used by the motor is continually monitored and compared to a predetermined value. If an overcurrent condition occurs, indicating a jamming of the airlock, a controller means starts a "soft" reverse rotation of the motor thereby clearing the jamming. Three patterns of the motor reversal are provided.

Groombridge, Clifton E. (Hardin, MT)

1996-01-01T23:59:59.000Z

347

Investigation of a rotary valving system with variable valve timing for internal combustion engines: Final technical report  

DOE Green Energy (OSTI)

The objective of the program was to provide a functional demonstration of the Hansen Rotary Valving System with Variable Valve timing (HRVS/VVT), capable of throttleless inlet charge control, as an alternative to conventional poppet-valves for use in spark ignited internal combustion engines. The goal of this new technology is to secure benefits in fuel economy, broadened torque band, vibration reduction, and overhaul accessibility. Additionally, use of the variable valve timing capability to vary the effective compression ratio is expected to improve multi-fuel tolerance and efficiency. Efforts directed at the design of HRVS components proved to be far more extensive than had been anticipated, ultimately requiring that proof-trial design/development work be performed. Although both time and funds were exhausted before optical or ion-probe types of in-cylinder investigation could be undertaken, a great deal of laboratory data was acquired during the course of the design/development work. This laboratory data is the basis for the information presented in this Final Report.

Cross, P.C.; Hansen, C.N.

1994-11-18T23:59:59.000Z

348

Microsoft Word - S05827_WCR_Final.doc  

Office of Legacy Management (LM)

MV-4 Data MV-4 Data This page intentionally left blank U.S. Department of Energy Well Completion Report for CAU 443 CNTA December 2009 Doc. No. S05827 Page B-1 Table B-1. MV-4 Chronology Date Time Depth (ft bgs) Activity 04/16/09 through 04/22/09 NA NA Mobilization to CNTA and rig-up to drill 04/22/09 15:45 0 Rig inspection and drill pad walk through inspection, continue with preparations for drilling. 04/22/09 21:50 0 Begin drilling 31-inch diameter conductor casing borehole 04/23/09 10:10 100 Advanced 31-inch borehole to completion depth 04/24/09 00:15 100 Completed tripping out of hole, setting, and cementing 24-inch diameter CS surface casing with 210 ft 3 cement. 04/24/09 13:00 100 Begin drilling 12.25-inch borehole using conventional mud rotary method, switch to flooded reverse circulation method at

349

Microsoft Word - S05827_WCR_Final.doc  

Office of Legacy Management (LM)

MV-5 Data MV-5 Data This page intentionally left blank U.S. Department of Energy Well Completion Report for CAU 443 CNTA December 2009 Doc. No. S05827 Page C-1 Table C-1. MV-5 Chronology Date Time Depth (ft bgs) Activity 05/09/09 through 05/10/09 NA NA Move rig and equipment from MV-4 pad to MV-5 pad and prepare to drill MV-5. 05/10/09 12:10 0 Rig inspection and drill pad walk through inspection, continue with preparations for drilling. 05/10/09 14:00 0 Begin drilling 31-inch diameter conductor casing borehole. 05/11/09 01:00 100 Advanced 31-inch borehole to completion depth. 05/11/09 12:00 100 Completed tripping out of hole, setting, and cementing 24-inch diameter CS surface casing with 210 ft 3 cement. 05/11/09 19:10 100 Begin drilling 12.25-inch borehole using conventional mud rotary method, switch to flooded reverse circulation method at

350

Enumeration of Juvenile Salmonids in the Okanogan Basin Using Rotary Screw Traps, Performance Period: March 15, 2006 - July 15, 2006.  

DOE Green Energy (OSTI)

The Colville Tribes identified the need for collecting baseline census data on the timing and abundance of juvenile salmonids in the Okanogan River basin for the purpose of documenting local fish populations, augmenting existing fishery data and assessing natural production trends of salmonids. This report documents and assesses the pilot year of rotary trap capture of salmonid smolts on the Okanogan River. The project is a component of the Colville Tribes Okanogan Basin Monitoring and Evaluation Program (OBMEP) which began in 2004. Trapping for outmigrating fish began on 14 March 2006 and continued through 11 July 2006. Anadromous forms of Oncorhynchus, including summer steelhead (O. mykiss), Chinook (O. tshawytscha), and sockeye (O. nerka), were targeted for this study; all have verified, natural production in the Okanogan basin. Both 8-ft and 5-ft rotary screw traps were deployed on the Okanogan River from the Highway 20 Bridge and typically fished during evening hours or 24 hours per day, depending upon trap position and discharge conditions. Juvenile Chinook salmon were the most abundant species trapped in 2006 (10,682 fry and 2,024 smolts), followed by sockeye (205 parr and 3,291 smolts) and steelhead (1 fry and 333 smolts). Of the trapped Chinook, all fry were wild origin and all but five of the smolts were hatchery-reared. All trapped sockeye were wild origin and 88% of the steelhead smolts were hatchery-reared. Mark-recapture experiments were conducted using Chinook fry and hatchery-reared steelhead smolts (sockeye were not used in 2006 because the peak of the juvenile migration occurred prior to the onset of the mark-recapture experiments). A total of 930 chinook fry were marked and released across eight separate release dates (numbers of marked Chinook fry released per day ranged from 34 to 290 fish). A total of 11 chinook fry were recaptured for an overall trap efficiency of 1.18%. A total of 710 hatchery-reared steelhead were marked and released across three separate release dates (numbers of steelhead released per day ranged from 100 to 500 fish). A total of 12 steelhead were recaptured for an overall trap efficiency of 1.69%. A pooled Peterson estimator with a Chapman modification was used to produce population estimates for wild Chinook fry and hatchery-reared steelhead based on the results of the mark-recapture experiments. The 2006 populations for Chinook and steelhead were estimated to be 381,554 (95% confidence intervals: 175,731-587,377) and 14,164 (6,999-21,330), respectively. The population estimates were based on the periods in which mark-recapture experiments were initialized through the end of the trapping season (10 May for steelhead and 1 June for Chinook).

Johnson, Peter N.; Rayton, Michael D.

2007-05-01T23:59:59.000Z

351

U.S. Department of Energy Office of Legacy Management National Envkonmental Policy Act Environmental Checklist  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

- - 19-10 U.S. Department of Energy Office of Legacy Management National Envkonmental Policy Act Environmental Checklist Project/Activity: Drill one exploratory hole on L.T. c-WM-17 by Golden Eagle Uranium A. Brief Project! Activity Descl'iptioll Golden Eagle Uranium (LLC) proposes to drill one 5-inch-diameter exploratory borehole on U.S. Department of Energy (DOE) lease tract C-WM-17, located in western Montrose County, Colorado. The drilling would be completed by a truck-mounted rotary drill rig capable of boring to 1,000 feet (ft) below ground surface (bgs). The proposed location of the drill hole is in a previously disturbed area and is adjacent to a two-track dirt road. Access to the site would be on existing dirt roads. The drilling would be completed dry to an estimated depth of 550 ft bgs. Once data are collected, the hole

352

Natural Gas Weekly Update, Printer-Friendly Version  

Gasoline and Diesel Fuel Update (EIA)

1, 2011 at 2:00 P.M. 1, 2011 at 2:00 P.M. Next Release: Thursday, August 18, 2011 Overview Prices Storage Other Market Trends Overview (For the Week Ending Wednesday, August 10, 2011) Natural gas prices fell across the board this week, likely in response to cooling temperatures as well as weak economic news. The Henry Hub spot price fell 17 cents from $4.26 per million Btu (MMBtu) last Wednesday, August 3, to $4.09 per MMBtu yesterday, August 10. At the New York Mercantile Exchange, the price of the near-month contract (September 2011) fell by $0.087 per MMBtu, from $4.090 last Wednesday to $4.003 yesterday. Working natural gas in storage was 2,783 Bcf as of Friday, August 5, according to EIAÂ’s Weekly Natural Gas Storage Report (WNGSR). The natural gas rotary rig count, as reported by Baker Hughes

353

Program or Field Office:  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Install six groundwater monitoring wells and perform general site actions at the Bluewater Install six groundwater monitoring wells and perform general site actions at the Bluewater Uranium Mill Tailings Radiation Control Act site near Grants, NM. LM 5-12 Location: Near Grants, NM Proposed Action or Project Description: DOE proposes to install six groundwater monitoring wells, perform other actions related to use of existing monitoring wells, obtain a Light Detection and Ranging Survey (LiDAR), install a small weather station, and apply pesticide to control noxious weeds at the Bluewater Site. The wells would be drilled by a truck-mounted rotary drill rig. The B SIB-inch boreholes would extend to depths of 120 to 350 feet (ft) below ground surface. Mud pits to contain drilling fluids and drill cuttings would be required for some of the wells. The mud pits, where required, would be approximately 6 ft by 20 ft in

354

CX-000283: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

283: Categorical Exclusion Determination 283: Categorical Exclusion Determination CX-000283: Categorical Exclusion Determination Cotter Corp Exploratory Drill Hole on Tract C-SR-13A CX(s) Applied: B3.1, B1.3 Date: 11/09/2009 Location(s): San Miguel County, Colorado Office(s): Legacy Management Cotter Corporation proposes to conduct exploratory drilling on Lease Tract C-SR-13A, located in San Miguel County, Colorado. The exploratory drilling would consist of boring one 5-6-inch diameter hole adjacent to an existing road to an estimated depth of 750 feet. A truck-mounted air rotary drill rig would be used for this action. In addition, a 10 x 10 x 3 feet deep excavated area would be used to contain the drill cuttings. DOCUMENT(S) AVAILABLE FOR DOWNLOAD CX-000283.pdf More Documents & Publications

355

Natural Gas Weekly Update  

Gasoline and Diesel Fuel Update (EIA)

3, 2011 at 2:00 P.M. 3, 2011 at 2:00 P.M. Next Release: Thursday, June 30, 2011 Overview Prices Storage Other Market Trends Natural Gas Transportation Update Overview (For the Week Ending Wednesday, June 22, 2011) Natural gas prices fell slightly at most market locations from Wednesday, June 15 to Wednesday, June 22. The Henry Hub price fell 10 cents from $4.52 per million Btu (MMBtu) last Wednesday to $4.42 per MMBtu yesterday. At the New York Mercantile Exchange, the price of the July 2011 near-month futures contract fell by 26 cents, or about 6 percent, from $4.58 last Wednesday to $4.32 yesterday. Working natural gas in storage rose to 2,354 this week, according to EIAÂ’s Weekly Natural Gas Storage Report (WNGSR). The natural gas rotary rig count, as reported by Baker Hughes

356

Natural Gas Weekly Update  

Gasoline and Diesel Fuel Update (EIA)

2, 2011 at 2:00 P.M. 2, 2011 at 2:00 P.M. Next Release: Thursday, September 29, 2011 Overview Prices Storage Other Market Trends Overview (For the Week Ending Wednesday, September 21, 2011) Natural gas spot prices declined at most market locations across the United States, as moderate temperatures led to declines in demand. Prices at the Henry Hub fell from $4.01 per MMBtu last Wednesday, September 14, to $3.78 per MMBtu yesterday. At the New York Mercantile Exchange, the price of the near-month futures contract (October 2011) dropped from $4.039 per MMBtu last Wednesday to $3.73 per MMBtu yesterday. Working natural gas in storage rose to 3,201 billion cubic feet (Bcf) as of Friday, September 16, according to EIAÂ’s Weekly Natural Gas Storage Report (WNGSR). The natural gas rotary rig count, as reported by Baker Hughes

357

Slim Holes At Alvord Hot Springs Area (Combs, Et Al., 1999) | Open Energy  

Open Energy Info (EERE)

Combs, Et Al., 1999) Combs, Et Al., 1999) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Slim Holes At Alvord Hot Springs Area (Combs, Et Al., 1999) Exploration Activity Details Location Alvord Hot Springs Area Exploration Technique Slim Holes Activity Date Usefulness not indicated DOE-funding Unknown Notes Anadarko Petroleum Corporation drilled two slimhole discoveries in the 1980s, one at Salt Wells, NV, and the other at Pueblo Valley, OR. Both of these slimholes were hot enough to discharge unassisted and were successfully flow tested. A slimhole at Pueblo Valley, in south-east Oregon was planned and permitted as a test well to evaluate an interval of fractured basalt which had been discovered while drilling an earlier thermal-gradient hole. Using a UDR1500 rig, the hole was rotary-drilled to

358

U.S. Department of Energy Office of Legacy Management National Environmental Policy Act Environmental Checklist  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2-10 2-10 U.S. Department of Energy Office of Legacy Management National Environmental Policy Act Environmental Checklist Project/Activity: Install wells and boreholes at the Old Rifle, CO, Processing Site A. Brief Project/Activity Description The Environmental Remediation Sciences Program (ERSP) proposes to install 36 wells and 5 boreholes on the Old Rifle, CO, Processing Site. A combination of 13 injection wells, 18 monitoring wells, 5 multi-chambered wells, and 5 boreholes would be installed using a sonic rotary drill rig. Five of the wells would be used for U.S. Department of Energy (DOE) Office of Legacy Management (LM) groundwater monitoring purposes and the remainder (31 wells and 5 boreholes) would be installed in a single gallery (Super 8) to be used for research and monitoring

359

Natural Gas Weekly Update  

Gasoline and Diesel Fuel Update (EIA)

1, 2011 at 2:00 P.M. 1, 2011 at 2:00 P.M. Next Release: Thursday, August 18, 2011 Overview Prices Storage Other Market Trends Overview (For the Week Ending Wednesday, August 10, 2011) Natural gas prices fell across the board this week, likely in response to cooling temperatures as well as weak economic news. The Henry Hub spot price fell 17 cents from $4.26 per million Btu (MMBtu) last Wednesday, August 3, to $4.09 per MMBtu yesterday, August 10. At the New York Mercantile Exchange, the price of the near-month contract (September 2011) fell by $0.087 per MMBtu, from $4.090 last Wednesday to $4.003 yesterday. Working natural gas in storage was 2,783 Bcf as of Friday, August 5, according to EIAÂ’s Weekly Natural Gas Storage Report (WNGSR). The natural gas rotary rig count, as reported by Baker Hughes

360

Natural Gas Weekly Update, Printer-Friendly Version  

Gasoline and Diesel Fuel Update (EIA)

8, 2011 at 2:00 P.M. 8, 2011 at 2:00 P.M. Next Release: Thursday, August 4, 2011 Overview Prices Storage Other Market Trends Overview (For the Week Ending Wednesday, July 27, 2011) As last weekÂ’s Eastern heat wave subsided, natural gas prices declined at market locations across the lower 48 States. The spot price at the Henry Hub decreased 18 cents from $4.64 per million Btu (MMBtu) last Wednesday, July 20, to $4.46 per MMBtu yesterday, July 27. At the New York Mercantile Exchange, the price of the near-month futures contract (August 2011) decreased from $4.500 per MMBtu to $4.370 per MMBtu. Working natural gas in storage rose to 2,714 billion cubic feet (Bcf) as of Friday, July 22, according to EIAÂ’s Weekly Natural Gas Storage Report (WNGSR). The natural gas rotary rig count, as reported by Baker Hughes

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

CX-002692: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

692: Categorical Exclusion Determination 692: Categorical Exclusion Determination CX-002692: Categorical Exclusion Determination Drill One Exploratory Hole On Lease Tract C-WM-17 by Golden Eagle Uranium CX(s) Applied: B3.1, B1.3 Date: 06/02/2010 Location(s): Montrose County, Colorado Office(s): Legacy Management Golden Eagle Uranium (LLC) proposes to drill one 5-inch-diameter exploratory borehole on U.S. Department of Energy (DOE) lease tract C-WM-17, located in western Montrose County, Colorado. The drilling would be completed by a truck-mounted rotary drill rig capable of boring to 1,000 feet (ft) below ground surface (bgs). The proposed location of the drill hole is in a previously disturbed area and is adjacent to a two-track dirt road. Access to the site would be on existing dirt roads. DOCUMENT(S) AVAILABLE FOR DOWNLOAD

362

CX-001631: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1631: Categorical Exclusion Determination 1631: Categorical Exclusion Determination CX-001631: Categorical Exclusion Determination Install Wells and Boreholes at the Old Rifle Colorado Processing Site CX(s) Applied: B3.1 Date: 04/15/2010 Location(s): Old Rifle, Colorado Office(s): Legacy Management The Environmental Remediation Sciences Program (ERSP) proposes to install 36 wells and 5 boreholes on the Old Rifle, Colorado, Processing Site. A combination of 13 injection wells, 18 monitoring wells, 5 multi-chambered wells, and 5 boreholes would be installed using a sonic rotary drill rig. Five of the wells would be used for U.S. Department of Energy (DOE) Office of Legacy Management (LM) groundwater monitoring purposes and the remainder (31 wells and 5 boreholes) would be installed in a single gallery (Super 8)

363

Natural Gas Weekly Update  

Gasoline and Diesel Fuel Update (EIA)

1, 2011 at 2:00 P.M. 1, 2011 at 2:00 P.M. Next Release: Thursday, July 28, 2011 Overview Prices Storage Other Market Trends Overview (For the Week Ending Wednesday, July 20, 2011) Responding to extremely hot weather this week, natural gas prices moved up at market locations across the lower 48 States. The spot price at the Henry Hub increased 21 cents from $4.43 per million Btu (MMBtu) last Wednesday, July 13, to $4.64 per MMBtu yesterday, July 20. At the New York Mercantile Exchange, the price of the near-month futures contract (August 2011) increased from $4.403 per MMBtu to $4.500 per MMBtu. Working natural gas in storage rose to 2,671 billion cubic feet (Bcf) as of Friday, July 15, according to EIAÂ’s Weekly Natural Gas Storage Report (WNGSR). The natural gas rotary rig count, as reported by Baker Hughes

364

Office of Legacy Management Categorical Exclusion Determination Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Install two groundwater monitoring wells at the Bluewater Uranium Mill Tailings Radiation Install two groundwater monitoring wells at the Bluewater Uranium Mill Tailings Radiation Control Act site near Grants, New Mexico. LM # 10-12 Location : Near Grants, New Mexico Proposed Action or Project Description: DO E proposes to install two groundwater monitoring wells- 20(M) and 11 (SG)- on the Bluewater disposal site using a truck-mounted rotary drill rig. The boreholes would extend to depths of 140 to 280 feet below ground surface and would be completed with a polyvinyl chloride casing that has an outside diameter of 4.5 inches . Water and bentonite would be used for the drilling fluid ; if the drilling company requires additives , DOE would require the use of green products . Drill cuttings , which would consist of ground-up native rock with bentonite

365

Natural Gas Weekly Update, Printer-Friendly Version  

Gasoline and Diesel Fuel Update (EIA)

2, 2011 at 2:00 P.M. 2, 2011 at 2:00 P.M. Next Release: Thursday, September 29, 2011 Overview Prices Storage Other Market Trends Overview (For the Week Ending Wednesday, September 21, 2011) Natural gas spot prices declined at most market locations across the United States, as moderate temperatures led to declines in demand. Prices at the Henry Hub fell from $4.01 per MMBtu last Wednesday, September 14, to $3.78 per MMBtu yesterday. At the New York Mercantile Exchange, the price of the near-month futures contract (October 2011) dropped from $4.039 per MMBtu last Wednesday to $3.73 per MMBtu yesterday. Working natural gas in storage rose to 3,201 billion cubic feet (Bcf) as of Friday, September 16, according to EIAÂ’s Weekly Natural Gas Storage Report (WNGSR). The natural gas rotary rig count, as reported by Baker Hughes

366

CX-002757: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

57: Categorical Exclusion Determination 57: Categorical Exclusion Determination CX-002757: Categorical Exclusion Determination Drill One Exploratory Borehole on Lease Tract 15A by Golden Eagle Uranium CX(s) Applied: B3.1, B1.3 Date: 06/15/2010 Location(s): San Miguel County, Colorado Office(s): Legacy Management Golden Eagle Uranium LLC proposes to drill one 5-inch diameter exploratory borehole on United States Department of Energy lease tract C-SR-15A, located in western San Miguel County, Colorado. The drilling would be completed by a truck-mounted rotary drill rig capable of boring to 1,000 feet below ground surface. The drilling would be completed dry to an estimated depth of 600 feet below ground surface. DOCUMENT(S) AVAILABLE FOR DOWNLOAD CX-002757.pdf More Documents & Publications CX-000283: Categorical Exclusion Determination

367

Natural Gas Weekly Update, Printer-Friendly Version  

Gasoline and Diesel Fuel Update (EIA)

1, 2011 at 2:00 P.M. 1, 2011 at 2:00 P.M. Next Release: Thursday, July 28, 2011 Overview Prices Storage Other Market Trends Overview (For the Week Ending Wednesday, July 20, 2011) Responding to extremely hot weather this week, natural gas prices moved up at market locations across the lower 48 States. The spot price at the Henry Hub increased 21 cents from $4.43 per million Btu (MMBtu) last Wednesday, July 13, to $4.64 per MMBtu yesterday, July 20. At the New York Mercantile Exchange, the price of the near-month futures contract (August 2011) increased from $4.403 per MMBtu to $4.500 per MMBtu. Working natural gas in storage rose to 2,671 billion cubic feet (Bcf) as of Friday, July 15, according to EIAÂ’s Weekly Natural Gas Storage Report (WNGSR). The natural gas rotary rig count, as reported by Baker Hughes

368

Application of polycrystalline diamond compact bits in the Kuparuk River Field, Alaska  

SciTech Connect

In soft to medium-hard clays and shales, polycrystalline diamond compact (PDC) bits have proved economically successful in the Kuparuk River field, AK. Through the redesign and modification of PDC bits and rig equipment, the necessary operating parameters have been achieved, and the use of PDC bits has become routine. These bits are typically run with a bit weight of 30,000 to 40,000 lbf (133 to 178 kN), a standpipe pressure of 4,000 psi (27 MPa), a pump rate of 400 to 450 gal/min (1.5 to 1.7 m/sup 3//min), and a rotary speed of 150 to 200 rev/min. Use of these high operating parameters saves about $50,000 per PDC bit when compared with roller-cone bits.

Balkenbush, R.J.; Onisko, J.E.

1985-07-01T23:59:59.000Z

369

Thermal spallation drilling  

DOE Green Energy (OSTI)

Thermal spallation drilling is an underdeveloped process with great potential for reducing the costs of drilling holes and mining shafts and tunnels in most very hard rocks. Industry has used this process to drill blast holes for emplacing explosives and to quarry granite. Some theoretical work has been performed, and many signs point to a great future for this process. The Los Alamos National Laboratory has studied the theory of the spallation process and is conducting experiments to prove out the system and to adapt it for use with a conventional rotary rig. This report describes work that has been accomplished at the Laboratory on the development of thermal spallation drilling and some work that is projected for the future on the system. 3 references, 3 figures.

Williams, R.E.

1985-01-01T23:59:59.000Z

370

Slimhole Drilling, Logging, and Completion Technology - An Update  

DOE Green Energy (OSTI)

Using slim holes (diameter < 15 cm) for geothermal exploration and small-scale power production can produce significant cost savings compared to conventional rotary-drilling methods. In addition, data obtained from slim holes can be used to lower the risks and costs associated with the drilling and completion of large-diameter geothermal wells. As a prime contractor to the U.S. Department of Energy (DOE), Sandia National Laboratories has worked with industry since 1992 to develop and promote drilling, testing, and logging technology for slim holes. This paper describes the current status of work done both in-house and contracted to industry. It focuses on drilling technology, case histories of slimhole drilling projects, data collection and rig instrumentation, and high-temperature logging tools.

FINGER,JOHN T.; JACOBSON,RONALD D.

1999-10-07T23:59:59.000Z

371

Drill report  

SciTech Connect

North Slope drilling activity is described. As of November 14, 1984, four rigs were actively drilling in the Kuparuk River field with another two doing workovers. Only one rig was drilling in the Prudhoe Bay field, with another doing workovers and one on standby.

Not Available

1984-12-01T23:59:59.000Z

372

Table Of Contents Section: Page  

E-Print Network (OSTI)

....................................................................15-6 15.E Rigging Hardware....................................................15-15 Tables: 15 the immediate work area and properly stored and maintained in a safe condition. 15.A.02 Hoist rope shall.04 When hoisting loads, a positive latching device shall be used to secure the load and rigging (e

US Army Corps of Engineers

373

Thermal Barrier Coatings for Superalloys  

Science Conference Proceedings (OSTI)

near-term means to dramatica?yl-y increase gas turbine inZet temperatures beyond those .... in rapid response furnaces, natural gas torch rigs, and Mach 1 burner rigs (5). Figure 3, adapted from .... under which liquid deposits are stable are.

374

Achieve Continuous Injection of Solid Fuels into Advanced Combustion System Pressures  

SciTech Connect

The overall objective of this project is the development of a mechanical rotary-disk feeder, known as the Stamet Posimetric High Pressure Solids Feeder System, to demonstrate feeding of dry granular coal continuously and controllably into pressurized environments of up to 70 kg/cm2 (1,000 psi). This is the Phase III of the ongoing program. Earlier Phases 1 and II successfully demonstrated feeding into pressures up to 35 kg/cm{sup 2} (500 psi). The final report for those phases was submitted in April 2005. Based on the previous work done in Phases I & II using Powder River Basin coal provided by the PSDF facility in Wilsonville, AL, a Phase III feeder system was designed and built to accomplish the target of feeding the coal into a pressure of 70 kg/cm2 (1,000 psi) and to be capable of feed rates of up to 550 kilograms (1,200lbs) per hour. The drive motor system from Phase II was retained for use on Phase III since projected performance calculations indicated it should be capable of driving the Phase III pump to the target levels. The pump & motor system was installed in a custom built test rig comprising an inlet vessel containing an active live-wall hopper mounted on weigh cells in a support frame, transition into the pump inlet, transition from pump outlet and a receiver vessel containing a receiver drum supported on weigh cells. All pressure containment on the rig was rated to105 kg/cm{sup 2} (1,500psi) to accommodate the final pressure requirement of a proposed Phase IV of the program. A screw conveyor and batch hopper were added to transfer coal at atmospheric pressure from the shop floor up into the test rig to enable continuous feeding up to the capacity of the receiving vessel. Control & monitoring systems were up-rated from the Phase II system to cover the additional features incorporated in the Phase III rig, and provide closer control and expanded monitoring of the entire system. A program of testing and modification was carried out in Stamet's facility in CA, culminating in the first successful feeding of coal into the Phase III target of 70 kg/cm{sup 2} (1,000 psi) gas pressure in March 2007. Subsequently, repeated runs at pressure were achieved, and comparison of the data with Phase II results when adjusted for scale differences showed further power reductions of 40% had been achieved from the final Phase II pressure runs. The general design layout of a commercial-scale unit was conducted, and preliminary cost estimates made.

Derek L. Aldred; Timothy Saunders

2007-03-31T23:59:59.000Z

375

Drillers find niche as market recovers  

Science Conference Proceedings (OSTI)

The drilling industry depression culminating in June of last year has seen equipment prices fall through the floor. But indications of a mild, steady recovery continue to surface; prices are beginning to rise. On result is foreign contractors are pushing to purchase refurbished rigs while prices are still low, as shown in this article. An example of this trend is Houston-Based Oil Drilling Products Inc.'s (ODP) recent considerable increase in activity. The company operates as a complete turnkey rig broker involving: findings rigs to meet buyer specifications; shipping the rigs to the ODP yard in Houston; completing any refurbishing or modifications previously agreed upon; and shipping the rig out to the buyer.

Wells, B.

1987-07-01T23:59:59.000Z

376

A safety assessment of rotary mode core sampling in flammable gas single shell tanks: Hanford Site, Richland, Washington  

SciTech Connect

This safety assessment (SA) addresses each of the required elements associated with the installation, operation, and removal of a rotary-mode core sampling (RMCS) device in flammable-gas single-shell tanks (SSTs). The RMCS operations are needed in order to retrieve waste samples from SSTs with hard layers of waste for which push-mode sampling is not adequate for sampling. In this SA, potential hazards associated with the proposed action were identified and evaluated systematically. Several potential accident cases that could result in radiological or toxicological gas releases were identified and analyzed and their consequences assessed. Administrative controls, procedures and design changes required to eliminate or reduce the potential of hazards were identified. The accidents were analyzed under nine categories, four of which were burn scenarios. In SSTS, burn accidents result in unacceptable consequences because of a potential dome collapse. The accidents in which an aboveground burn propagates into the dome space were shown to be in the ``beyond extremely unlikely`` frequency category. Given the unknown nature of the gas-release behavior in the SSTS, a number of design changes and administrative controls were implemented to achieve these low frequencies. Likewise, drill string fires and dome space fires were shown to be very low frequency accidents by taking credit for the design changes, controls, and available experimental and analytical data. However, a number of Bureau of Mines (BOM) tests must be completed before some of the burn accidents can be dismissed with high confidence. Under the category of waste fires, the possibility of igniting the entrapped gases and the waste itself were analyzed. Experiments are being conducted at the BOM to demonstrate that the drill bit is not capable of igniting the trapped gas in the waste. Laboratory testing and thermal analysis demonstrated that, under normal operating conditions, the drill bit will not create high enough temperatures to initiate a propagating reaction in the waste. However, system failure that coincides in a waste layer with high organic content and low moisture may initiate an exothermic reaction in the waste. Consequently, a conservative approach based on the current state of the knowledge resulted in limiting the drilling process to a subset of the flammable-gas tanks. Accidents from the chemical reactions and criticality category are shown to result in acceptable risk. A number of accidents are shown to potentially result in containment (tank liner) breach below the waste level. Mitigative features are provided for these accidents. Gas-release events without burn also are analyzed, and radiological and toxicological consequences are shown to be within risk guidelines. Finally, the consequences of potential spills are shown to be within the risk guidelines.

Raymond, R.E.

1996-04-15T23:59:59.000Z

377

Development of a cable reel development system using a rotary joint for kilometer lengths of two-fiber multi-mode fiber optic cable  

SciTech Connect

Brookhaven National Laboratory (BNL) recently developed a two-component system for use during remote inspections. The system consists of a mobile unit with television cameras and other equipment and a stationary base station. A variety of signals must be continually transmitted between the two system components as the mobile unit is moved from the location to another. Two channels of broadband (10MHz) NTSC video are transmitted from the mobile unit to the base station, and a bi-directional ``talk set`` provides audio communication between personnel at each location. In addition, several channels of RS-232 are required to support present and future instruments used at the mobile unit and controlled by personnel at the base station. Brookhaven developed a mobile unit which communicated with a base station over a 2-fiber multimode fiber optic cable. One of the design requirements was maintaining constant communication with the base station during the time the mobile unit was moved about. To provide uninterrupted communications, deployment of the 1-km long fiber optic cable was initially performed with a ``spinning reel`` mechanism. The spinning reel mechanism proved to be mechanically unsuitable, and so the cable deployment mechanism was redesigned to spool the cable off the reel. The requirement for uninterrupted communications required a two-channel fiber optic rotary joint in the design. Incorporation of the rotary joint into the design is described, and appropriate reference material is included.

Curtiss, J.A.; Jahelka, J.R.

1995-08-11T23:59:59.000Z

378

Rotary bulk solids divider  

DOE Patents (OSTI)

An apparatus for the disbursement of a bulk solid sample comprising, a gravity hopper having a top open end and a bottom discharge end, a feeder positioned beneath the gravity hopper so as to receive a bulk solid sample flowing from the bottom discharge end, and a conveyor receiving the bulk solid sample from the feeder and rotating on an axis that allows the bulk solid sample to disperse the sample to a collection station.

Maronde, Carl P. (McMurray, PA); Killmeyer, Jr., Richard P. (Pittsburgh, PA)

1992-01-01T23:59:59.000Z

379

Rotary drilling jar  

SciTech Connect

This patent describes an improved jar for use in freeing well tools and the like stuck in a well bore. The improvement comprises: tubular, inner mandrel means having a downwardly facing shoulder and having an annular groove in an exterior surface located relatively below the shoulder. The annular groove in the inner mandrel means tapers inwardly from an exterior surface of the inner mandrel means. The inner mandrel means are arranged for connection to a conduit when positioned in the well bore; and tubular, outer mandrel means encircling the inner mandrel means and arranged at a lower end for connection to the well to tool and having an upwardly facing abutment engageable with the downwardly facing shoulder.

Loeb, J.B.; Osborne, A.J.; Miglierini, R.A.

1987-05-05T23:59:59.000Z

380

Rotary slot dog  

SciTech Connect

A clamp or dog is disclosed which preferably comprises a slotted stepped cylindrical body which is inserted into a hole in a workpiece and then fastened to a base or fixture using a screw which is inserted through the slot. The stepped configuration provides an annular clamping surface which securely clamps the workpiece against the base or fixture. The slotted cylindrical configuration permits adjustment of the workpiece and retaining clamp in any direction, i.e., over 360.degree., relative to the mounting position of the screw in the base or fixture.

Cutburth, Ronald W. (Tracy, CA); Smauley, David A. (Livermore, CA)

1987-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Une note sur l'origine du concept des huit categories d'esprits  

E-Print Network (OSTI)

avec le système social des castesdans les textes consacrés au culte des klu. On y trouve rje rigs, les seigneursdes klu, bram ze rigs, les brahmanes, et gdol ba’i rigs, les intouchables. dri et btsanDeux catégorie de dri (ou dri bo, l. 363) sont... ) donne la date 823 ainsi que Stein (1983 : 215) citant Z. Yamagu-chi, mais les critères qui ont servi à cette datation ne sont pas clairs pour moi.25 Macdonald, Imaeda, 1978 : Pl. 10 (28a, l.4): ...byang chub sems dpa’ chen po brgyaddang/ khro bo gnyis...

Karmay, Samten G

2003-01-01T23:59:59.000Z

382

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

21 - 24430 of 26,764 results. 21 - 24430 of 26,764 results. Download Examination Report: OAS-RA-13-23 Area Community Services Employment and Training Council - Weatherization Assistance Program Funds Provided by the American Recovery and Reinvestment Act of 2009 http://energy.gov/ig/downloads/examination-report-oas-ra-13-23 Download DOE-STD-1090-2011 Hoisting and Rigging (Formerly Hoisting and Rigging Manual) Superseding DOE-STD-1090-2007 (August 2007) The U.S. Department of Energy (DOE) Hoisting and Rigging Standard is intended to be used by supervisors, line managers, safety personnel, equipment operators, riggers and other personnel responsible for the safety of hoisting and rigging operations at DOE sites. It may be used as either contract document or as a best practices guide at the site's or program

383

Technical Standards, DOE-STD-1090-2004 - June 01, 2004 | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

04 - June 01, 2004 Technical Standards, DOE-STD-1090-2004 - June 01, 2004 June 01, 2004 DOE-STD-1090-2004: Hoisting and Rigging Standard The U.S. Department of Energy (DOE)...

384

U S D  

NLE Websites -- All DOE Office Websites (Extended Search)

Turbine Drilling System Hybrid CT Drill Rig 4 Novel High-Speed Drilling Motor for Oil Exploration & Production DE-FC26-04NT15501 Goal The project goal is to design and develop...

385

20131217_RMOTC_SaleItems_Inventory_New.pages  

NLE Websites -- All DOE Office Websites (Extended Search)

* Frieghtliner C13 Smeal Rig * Frieghliner FL80 Klaeger Unit * International F2574 Hot Oil Truck * Plus various pump jacks, electric pump motors 1.5 to 25 HP, casing, sucker...

386

Laser Oil & Gas Well Drilling [Laser Applications Laboratory...  

NLE Websites -- All DOE Office Websites (Extended Search)

benefit in reducing the high costs of operating a drill rig. Today, a typical land-based oil or gas well costs around 400,000 to drill, while costs for an offshore well average...

387

755.ps  

E-Print Network (OSTI)

de ned by a cost function f and a set of feasible solutions X, where we seek an optimal solution. x 2 X such that f(x ) ..... rigs for onshore oil production. Technical  ...

388

Transnational Zapata: From the Ejército Zapatista de Liberación Nacional to Immigrant Marches  

E-Print Network (OSTI)

which Rivera’s image of foreign oil companies alludes. Yetby images of foreign-owned oil rigs and oil companies.hand, and foreign powers represented through globalized oil

Slaughter, Stephany

2012-01-01T23:59:59.000Z

389

41220R8.prn  

NLE Websites -- All DOE Office Websites (Extended Search)

50% compared to the existing lean premixed gas turbine combustors. 3.1.1 Component Design Utilizing the existing Air Force Research Lab (AFRL) 6" rectangular TVC rig, new...

390

The Value of Hurricane Forecasts to Oil and Gas Producers in the Gulf of Mexico  

Science Conference Proceedings (OSTI)

The threat of hurricanes often forces producers of crude oil and natural gas in the Gulf of Mexico to evacuate offshore drilling rigs and temporarily to cease production. More accurate hurricane forecasts would result in fewer false alarms, ...

Timothy J. Considine; Christopher Jablonowski; Barry Posner; Craig H. Bishop

2004-09-01T23:59:59.000Z

391

Drilling Waste Management Fact Sheet: Onsite Burial (Pits, Landfills...  

NLE Websites -- All DOE Office Websites (Extended Search)

management. During most U.S. onshore drilling operations, the cuttings separated by the shale shaker are sent to a pit called the reserve pit located near the drill rig. The pit is...

392

NETL: Methane Hydrates - ANS Research Project  

NLE Websites -- All DOE Office Websites (Extended Search)

Plan Science Plan The Mt. Elbert prospect will be drilled as a vertical stratigraphic test using the Doyon 14 rig. The well is being drilled beneath an exploration ice pad...

393

Scalable multi-view stereo camera array for real world real-time image capture and three-dimensional displays  

E-Print Network (OSTI)

The number of three-dimensional displays available is escalating and yet the capturing devices for multiple view content are focused on either single camera precision rigs that are limited to stationary objects or the use ...

Hill, Samuel L. (Samuel Lincoln), 1978-

2004-01-01T23:59:59.000Z

394

MHK Technologies/New Knowledge Wind and Wave Renewable Mobile...  

Open Energy Info (EERE)

Description Buoyant vessel attached to a lever the lever being attached to a stationary source like near shore Oil Rigs docks or a vessel less affected by swells and waves like...

395

Name Santiago Andrs Triana Address 613 Blossom Drive, Rockville, MD 20850, USA  

E-Print Network (OSTI)

software and hardware control systems for the 3-meter Sodium Geodynamo Experiment; conduct experimental runs, perform data analysis and write scientific reports. Organization Institute for Research Technical drawing, machining, gas metal arc welding, hazardous materials handling, heavy load rigging

Lathrop, Daniel P.

396

Observed and Computed M2 Tidal Currents in the North Sea  

Science Conference Proceedings (OSTI)

M2 tidal elevations and currents have been computed using a three-dimensional hydrodynamic numerical model of the northwest European shelf. These have been compared with observational data from tide gages and current meter rigs moored in ...

A. M. Davies; G. K. Furnes

1980-02-01T23:59:59.000Z

397

ESM 254 Course Syllabus COASTAL MARINE ECOSYSTEM PROCESSES  

E-Print Network (OSTI)

Lecture ­ Wetland mitigation and restoration in southern CA - Dr Thursday Discussion - Rigs to reefs: should decommissioned POCS oil platforms be used as reefs? Papers: (1) Kaiser MJ. 2006. The Louisiana artificial

California at Santa Barbara, University of

398

West Virginia, southwest Pennsylvania form an integrated natural ...  

U.S. Energy Information Administration (EIA)

Source: U.S. Energy Information Administration with data from DrillingInfo Note: The map shows the location of drilling rigs in the Appalachian basin on August 20, 2013.

399

--No Title--  

NLE Websites -- All DOE Office Websites (Extended Search)

Communications 865.576.0226 Stretch of I-40 part of ORNL, UT environmental lab initiative OAK RIDGE, Tenn., Dec. 19, 2002 - Twenty-five thousand big rigs rumbling through Knoxville...

400

Technical Standards, DOE-STD-1090-2007 - August 29, 2007 | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

07 - August 29, 2007 Technical Standards, DOE-STD-1090-2007 - August 29, 2007 August 29, 2007 DOE-STD-1090-2007: Hoisting and Rigging Standard The reissued June 1995 edition marked...

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Word Pro - Untitled1  

U.S. Energy Information Administration (EIA) Indexed Site

By Type, 1949-2011 By Type, 2011 94 U.S. Energy Information Administration Annual Energy Review 2011 1 Rigs drilling for miscellaneous purposes, such as service wells,...

402

The sGang steng-b rNying ma'i rGyud manuscript from Bhutan  

E-Print Network (OSTI)

first folios, itsimply gives the volume identification and pagination in gold ink. 6 Volumes Ka, Pa, Ra, Ha to Ki, Gi, Ci, Chi, Nyi, Thi, Ni, Pi, Bi, and Mi 7 This is unlike the Rig 'dzin edition, where...

Cathy Cantwell; Mayer, Rob

2006-01-01T23:59:59.000Z

403

NETL: Methane Hydrates - DOE/NETL Projects  

NLE Websites -- All DOE Office Websites (Extended Search)

at Mallik 2L-38 location Rig at Mallik 2L-38 location courtesy Geological Survey of Canada DE-AT26-97FT34342 Goal The purpose of this project is to assess the recoverability and...

404

Method and apparatus for forming billets from metallic chip scraps  

DOE Patents (OSTI)

After recycled titanium alloy chips are crushed and cleaned, they are pressed into cylindrically briquettes with a relative density of 0.6, and placed into capsules. The capsules are heated and placed into a preheated pressing rig. The pressing rig repetitively applies axial force to the capsule, resulting in a relative density of at least 0.95. The product billets are used for consumable electrodes, secondary casting alloys, forgings, extruded semi-finished products and the like.

Girshov, Vladimir Leonidovich (St. Petersburg, RU); Treschevskiy, Arnold Nikolayevich (St. Petersburg, RU); Kochkin, Victor Georgievich (St. Petersburg, RU); Abramov, Alexey Alexandrovich (St. Petersburg, RU); Sidenko, Natalja Semenovna (St. Petersburg, RU)

2006-05-02T23:59:59.000Z

405

Scale effects in tests on footings  

E-Print Network (OSTI)

Blanc, 1981). Like interpretation of penetrometer data, the main point of interest for spudcan design has always been the evaluation of failure loads. It is because spudcans have to be pushed into the seabed to a predetermined depth with ballast on the rig... during preloading before unloading the oil rigs to their normal working conditions. This is a safeguard against accidental overloading and scouring of the seabed by under current which may undermine their foundations during their working life...

Lau, Chi Keung

1988-02-21T23:59:59.000Z

406

Development and testing of a Mudjet-augmented PDC bit.  

DOE Green Energy (OSTI)

This report describes a project to develop technology to integrate passively pulsating, cavitating nozzles within Polycrystalline Diamond Compact (PDC) bits for use with conventional rig pressures to improve the rock-cutting process in geothermal formations. The hydraulic horsepower on a conventional drill rig is significantly greater than that delivered to the rock through bit rotation. This project seeks to leverage this hydraulic resource to extend PDC bits to geothermal drilling.

Black, Alan (TerraTek, Inc.); Chahine, Georges (DynaFlow, Inc.); Raymond, David Wayne; Matthews, Oliver (Security DBS); Grossman, James W.; Bertagnolli, Ken (US Synthetic); Vail, Michael (US Synthetic)

2006-01-01T23:59:59.000Z

407

Don't mess with H/sub 2/S  

Science Conference Proceedings (OSTI)

The American Petroleum Institute issued a report on ''Recommended Practices for Safe Drilling of Wells Containing Hydrogen Sulfide.'' The study (RP49) updates a first edition published in September 1974. It provides a solid overview of preventive steps that should be taken to safeguard crew and equipment when drilling through H/sub 2/S zones. Discussions cover personnel training, protective equipment, wellsite layout, rig and well equipment, general rig operations and contingency planning and emergency procedures. This article summarizes the report.

Not Available

1987-09-01T23:59:59.000Z

408

Reduction of iron-oxide-carbon composites: part II. Rates of reduction of composite pellets in a rotary hearth furnace simulator  

SciTech Connect

A new ironmaking concept is being proposed that involves the combination of a rotary hearth furnace (RHF) with an iron-bath smelter. The RHF makes use of iron-oxide-carbon composite pellets as the charge material and the final product is direct-reduced iron (DRI) in the solid or molten state. This part of the research includes the development of a reactor that simulated the heat transfer in an RHF. The external heat-transport and high heating rates were simulated by means of infrared (IR) emitting lamps. The reaction rates were measured by analyzing the off-gas and computing both the amount of CO and CO{sub 2} generated and the degree of reduction. The reduction times were found to be comparable to the residence times observed in industrial RHFs. Both artificial ferric oxide (PAH) and naturally occurring hematite and taconite ores were used as the sources of iron oxide. Coal char and devolatilized wood charcoal were the reductants. Wood charcoal appeared to be a faster reductant than coal char. However, in the PAH-containing pellets, the reverse was found to be true because of heat-transfer limitations. For the same type of reductant, hematite-containing pellets were observed to reduce faster than taconite-containing pellets because of the development of internal porosity due to cracking and fissure formation during the Fe2O{sub 3}-to-Fe3O{sub 4} transition. This is, however, absent during the reduction of taconite, which is primarily Fe3O{sub 4}. The PAH-wood-charcoal pellets were found to undergo a significant amount of swelling at low-temperature conditions, which impeded the external heat transport to the lower layers. If the average degree of reduction targeted in an RHF is reduced from 95 to approximately 70 pct by coupling the RHF with a bath smelter, the productivity of the RHF can be enhanced 1.5 to 2 times. The use of a two- or three-layer bed was found to be superior to that of a single layer, for higher productivities.

Halder, S.; Fruehan, R.J. [Praxair Inc., Tonawanda, NY (United States). Praxair Technological Center

2008-12-15T23:59:59.000Z

409

Conveyor with rotary airlock apparatus  

DOE Patents (OSTI)

This invention is comprised of an apparatus for transferring objects from a first region to a second region, the first and second regions having differing atmospheric environments. The apparatus includes a shell having an entrance and an exit, a conveyer belt running through the shell from the entrance to the exit, and a horizontally mounted `revolving door` with at least four vanes revolving about its axis. The inner surface of the shell and the top surface of the conveyer belt act as opposing walls of the `revolving door`. The conveyer belt dips as it passes under but against the revolving vanes so as not to interfere with them but to engage at least two of the vanes and define thereby a moving chamber. Preferably, the conveyer belt has ridges or grooves on its surface that engage the edges of the vanes and act to rotate the vane assembly. Conduits are provided that communicate with the interior of the shell and allow the adjustment of the atmosphere of the moving chamber or recovery of constituents of the atmosphere of the first region from the moving chamber before they escape to the second region.

Kronbert, J.W.

1993-01-01T23:59:59.000Z

410

Rotary powder feed through apparatus  

DOE Patents (OSTI)

A device for increasing the uniformity of solids within a solids fabrication system, such as a direct light fabrication (DLF) system in which gas entrained powders are passed through the focal point of a moving high-power light which fuses the particles in the powder to a surface being built up in layers. The invention provides a feed through interface wherein gas entrained powders input from stationary input lines are coupled to a rotating head of the fabrication system. The invention eliminates the need to provide additional slack in the feed lines to accommodate head rotation, and therefore reduces feed line bending movements which induce non-uniform feeding of gas entrained powder to a rotating head.

Lewis, Gary K. (Los Alamos, NM); Less, Richard M. (Los Alamos, NM)

2001-01-01T23:59:59.000Z

411

C:\ANNUAL\VENTCHAP.V8\NGA.VP  

Gasoline and Diesel Fuel Update (EIA)

Energy Energy Information Administration / Natural Gas Annual 1997 10 Wellhead Prices The average wellhead price rose in 1997 for the second year in a row. It reached $2.32 per thousand cubic feet, 7 percent more than the 1996 price of $2.17 and 50 percent above the 1995 low of $1.55. Average wellhead prices during 1996 and 1997 were at their highest level since the 1982 through 1985 time period when they peaked in the range of $2.51 to $2.66 per thousand cubic feet. The 1997 price of $2.32 per thousand cubic feet still was more than 41 percent below the 1983 peak after adjustment for inflation. Drilling Exploration and development activities incrementally added to proved reserves of natural gas. In 1997, natural gas reserves reached 167,223 billion cubic feet, and reserve ad- ditions replaced production for the fourth year in a row. The number of rotary rigs running and the number of well com- pletions

412

Natural Gas Weekly Update  

Gasoline and Diesel Fuel Update (EIA)

7, 2011 at 2:00 P.M. 7, 2011 at 2:00 P.M. Next Release: Thursday, April 14, 2011 Overview Prices Storage Other Market Trends Natural Gas Transportation Update Overview (For the Week Ending Wednesday, April 6, 2011) Continuing last weekÂ’s net decline, the Henry Hub price this week fell 8 cents from $4.25 per million Btu (MMBtu) on Wednesday, March 30, to $4.17 per MMBtu on Wednesday, April 6. At the New York Mercantile Exchange, the price of the near-month (May 2011) contract fell from $4.355 per MMBtu to $4.146 per MMBtu. Working natural gas in storage fell to 1,579 billion cubic feet (Bcf) as of Friday, April 1, according to EIAÂ’s Weekly Natural Gas Storage Report.The natural gas rotary rig count, as reported by Baker Hughes Incorporated, rose by 11 to 891. A new study released by EIA estimated technically recoverable shale

413

Natural Gas Weekly Update, Printer-Friendly Version  

Gasoline and Diesel Fuel Update (EIA)

7, 2011 at 2:00 P.M. 7, 2011 at 2:00 P.M. Next Release: Thursday, April 14, 2011 Overview Prices Storage Other Market Trends Natural Gas Transportation Update Overview (For the Week Ending Wednesday, April 6, 2011) Continuing last weekÂ’s net decline, the Henry Hub price this week fell 8 cents from $4.25 per million Btu (MMBtu) on Wednesday, March 30, to $4.17 per MMBtu on Wednesday, April 6. At the New York Mercantile Exchange, the price of the near-month (May 2011) contract fell from $4.355 per MMBtu to $4.146 per MMBtu. Working natural gas in storage fell to 1,579 billion cubic feet (Bcf) as of Friday, April 1, according to EIAÂ’s Weekly Natural Gas Storage Report.The natural gas rotary rig count, as reported by Baker Hughes Incorporated, rose by 11 to 891. A new study released by EIA estimated technically recoverable shale

414

Coiled tubing drilling (CTD) moves to commercial viability  

Science Conference Proceedings (OSTI)

Shell Western E and P, Inc. (SWEPI) California Drilling Operations was interested in coiled tubing (CT) for drilling slimhole steam injectors. A four-well pilot project at South Belridge field, Kern County, Calif., was targeted for immediate CT use. Well programs included completion, a goal not previously attempted on wells drilled from surface with CT. This paper reviews the primary project focus which was to develop slimhole steam injectors and improve injection profiles in lower Tulare formation E and G sands. Feasibility of drilling wells with CT and having CT crews run and cement completion tubulars in place was an issue to be determined. Conventional tubing installation is usually outside the scope of CT operations, so it was not known if this would be technically or economically feasible. Another goal was to refine personnel expertise to further develop CTD services as a successful business line. Other items targeted for investigation were: deviation control; lost circulation solutions; WOB optimization to obtain maximum ROP; potential steam blowout intervals; and high temperature. Finally, economic feasibility of using CTD as a rotary rig alternative for specific applications like slimhole wells on sites where surface location is limited was to be determined.

Romagno, R. (Shell Western E and P, Inc., Bakersfield, CA (United States)); Walker, R. (Schlumberger Dowell, Bakersfield, CA (United States))

1994-12-01T23:59:59.000Z

415

Electric top drives gain wide industry acceptance  

Science Conference Proceedings (OSTI)

Since its introduction, the top drive drilling system has gained acceptance as a productive and safe method for drilling oil and gas wells. Originally, the system was used mostly for offshore and higher cost land drilling, and it had to be installed as a permanent installation because of its enormous weight and size. Essentially, a top drive replaces the kelly and rotary table as the means of rotating drillpipe on oil, gas and geothermal rigs and is considered to be 15% to 40% more efficient than a kelly drive. Top drive systems allow the operator to drill and maintain directional orientation for triple stands and provide tripping efficiency because of the ability to ream and circulate with triple stands, to reduce the risk of stuck pipe or lost wells, and to improve well control and pipe handling safety. The paper describes electric top drives with DC motors, top drives with AC motors, top drives with permanent magnet motors, and top drives with permanent magnet brushless synchronous motors.

Riahi, M.L.

1998-05-01T23:59:59.000Z

416

U. S. Energy Information Administration | Drilling Productivity Report  

U.S. Energy Information Administration (EIA) Indexed Site

1,600 1,600 2007 2008 2009 2010 2011 2012 2013 2014 Oil production thousand barrels/day Permian 0 10 20 30 Dec 1,335 Mbbl/d Production from new wells Legacy production change Net change Jan 1,335 Mbbl/d thousand barrels/day Permian +37 -36 +1 Indicated change in oil production (Jan vs. Dec) 0 20 40 60 80 Dec 5,046 MMcf/d Production from new wells Legacy production change Net change Jan 5,046 MMcf/d Indicated change in natural gas production (Jan vs. Dec) million cubic feet/day Permian +88 -88 +0 0 100 200 300 400 500 600 0 100 200 300 400 500 600 2007 2008 2009 2010 2011 2012 2013 2014 new-well oil production per rig rig count New-well oil production per rig barrels/day Permian Rig count rigs (40) (35) (30) (25) (20) (15) (10) (5) 0 2007 2008 2009 2010 2011 2012 2013 2014 Legacy oil production change thousand barrels/day

417

U. S. Energy Information Administration | Drilling Productivity Report  

U.S. Energy Information Administration (EIA) Indexed Site

barrels/day barrels/day 0 400 800 1,200 1,600 2,000 2007 2008 2009 2010 2011 2012 2013 2014 Oil production thousand barrels/day Haynesville 0.0 0.5 1.0 1.5 2.0 Dec 54 Mbbl/d Production from new wells Legacy production change Net change Jan 54 Mbbl/d thousand barrels/day Haynesville +2 -2 +0 Indicated change in oil production (Jan vs. Dec) -150 -50 50 150 250 350 Dec 6,492 MMcf/d Production from new wells Legacy production change Net change Jan 6,361 MMcf/d Indicated change in natural gas production (Jan vs. Dec) million cubic feet/day Haynesville +239 -370 -131 0 50 100 150 200 250 300 0 200 400 600 800 1,000 2007 2008 2009 2010 2011 2012 2013 2014 new-well oil production per rig rig count New-well oil production per rig barrels/day Haynesville Rig count rigs (3) (2) (1) 0 2007 2008 2009 2010 2011 2012 2013 2014 Legacy oil production change

418

U. S. Energy Information Administration | Drilling Productivity Report  

U.S. Energy Information Administration (EIA) Indexed Site

Bakken Bakken 0 50 100 Dec 1,000 Mbbl/d Production from new wells Legacy production change Net change Jan 1,025 Mbbl/d thousand barrels/day Bakken +88 -63 +25 Indicated change in oil production (Jan vs. Dec) 0 50 100 Dec 1,092 MMcf/d Production from new wells Legacy production change Net change Jan 1,119 MMcf/d Indicated change in natural gas production (Jan vs. Dec) million cubic feet/day Bakken +83 -55 +28 0 50 100 150 200 250 0 100 200 300 400 500 600 2007 2008 2009 2010 2011 2012 2013 2014 new-well oil production per rig rig count New-well oil production per rig barrels/day Bakken Rig count rigs (70) (60) (50) (40) (30) (20) (10) 0 2007 2008 2009 2010 2011 2012 2013 2014 Legacy oil production change thousand barrels/day Bakken (60) (50) (40) (30) (20) (10) 0 2007 2008 2009 2010 2011 2012 2013 2014 Legacy gas production change

419

U. S. Energy Information Administration | Drilling Productivity Report  

U.S. Energy Information Administration (EIA) Indexed Site

Marcellus Marcellus 0 400 800 1,200 1,600 2,000 2007 2008 2009 2010 2011 2012 2013 2014 Oil production thousand barrels/day Marcellus 0.0 1.0 2.0 3.0 4.0 Dec 39 Mbbl/d Production from new wells Legacy production change Net change Jan 41 Mbbl/d thousand barrels/day Marcellus +4 -2 +2 Indicated change in oil production (Jan vs. Dec) 0 200 400 600 Dec 13,303 MMcf/d Production from new wells Legacy production change Net change Jan 13,721 MMcf/d Indicated change in natural gas production (Jan vs. Dec) million cubic feet/day Marcellus +612 -193 +419 0 20 40 60 80 100 120 140 160 0 200 400 600 800 1,000 2007 2008 2009 2010 2011 2012 2013 2014 new-well oil production per rig rig count New-well oil production per rig barrels/day Marcellus Rig count rigs (3) (2) (1) 0 2007 2008 2009 2010 2011 2012 2013 2014 Legacy oil production change

420

Achieve Continuous Injection of Solid Fuels into Advanced Combustion System Pressures  

SciTech Connect

The overall objective of this project is the development of a mechanical rotary-disk feeder, known as the Stamet Posimetric High Pressure Solids Feeder System, to feed dry granular coal continuously and controllably into pressurized environments of up to 35 kg/cm{sup 2} (500 psi). This was to be accomplished in two phases. The first task was to review materials handling experience in pressurized operations as it related to the target pressures for this project, and review existing coal preparation processes and specifications currently used in advanced combustion systems. Samples of existing fuel materials were obtained and tested to evaluate flow, sealing and friction properties. This provided input data for use in the design of the Stamet Feeders for the project, and ensured that the material specification used met the requirements of advanced combustion & gasification systems. Ultimately, Powder River Basin coal provided by the PSDF facility in Wilsonville, AL was used as the basis for the feeder design and test program. Based on the material property information, a Phase 1 feeder system was designed and built to accomplish feeding the coal to an intermediate pressure up to 21 kg/cm{sup 2} (300 psi) at feed rates of approximately 100 kilograms (220lbs) per hour. The pump & motor system was installed in a custom built test rig comprising an inlet vessel containing an active live-wall hopper mounted in a support frame, transition into the pump inlet, transition from pump outlet and a receiver vessel containing a receiver drum supported on weigh cells. All pressure containment on the rig was rated for the final pressure requirement of 35 kg/cm{sup 2} (500psi). A program of testing and modification was carried out in Stamet's facility in CA, culminating in successful feeding of coal into the Phase 1 target of 21 kg/cm{sup 2} (300psi) gas pressure in December 2003. Further testing was carried out at CQ Inc's facility in PA, providing longer run times and experience of handling and feeding the coal in winter conditions. Based on the data developed through the testing of the Phase I unit, a Phase II system was designed for feeding coal into pressures of up to 35 kg/cm{sup 2} (500 psi). A further program of testing and modification was then carried out in Stamet's facility, with the target pressure being achieved in January 2005. Repeated runs at pressure were achieved, and optimization of the machine resulted in power reductions of 60% from the first successful pressure runs. General design layout of a commercial-scale unit was conducted, and preliminary cost estimates for a commercial unit obtained.

Derek L. Aldred; Timothy Saunders

2005-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

71 - 23980 of 26,764 results. 71 - 23980 of 26,764 results. Download Independent Oversight Inspection, Oak Ridge National Laboratory- October 2008 Inspection of Nuclear Safety at the Oak Ridge National Laboratory Radiochemical Engineering Development Center, Building 7920 http://energy.gov/hss/downloads/independent-oversight-inspection-oak-ridge-national-laboratory-1 Download HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office Facility Representative Division : To determine that hoisting and rigging operations areconducted according to "industry best standards" for increasing equipment reliabilitywhile assuring worker safety, and to verify issues being... http://energy.gov/hss/downloads/hoisting-rigging-assessment-plan-nnsanevada-site-office-facility Download 1Q CY2010 (PDF), Facility Representative Program Performance

422

Oak Ridge: Approaching 4 Million Safe Work Hours | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Oak Ridge: Approaching 4 Million Safe Work Hours Oak Ridge: Approaching 4 Million Safe Work Hours Oak Ridge: Approaching 4 Million Safe Work Hours February 27, 2013 - 12:00pm Addthis Mike Tidwell performs a leak check and inspection on propane tanks Mike Tidwell performs a leak check and inspection on propane tanks Inspections ensure hoisting and rigging equipment performs correctly so employees can safely complete their tasks Inspections ensure hoisting and rigging equipment performs correctly so employees can safely complete their tasks Mike Tidwell performs a leak check and inspection on propane tanks Inspections ensure hoisting and rigging equipment performs correctly so employees can safely complete their tasks OAK RIDGE, Tenn. - Workers at URS | CH2M Oak Ridge (UCOR), the prime contractor for EM's Oak Ridge cleanup, are approaching a milestone of 4

423

Microsoft PowerPoint - Pg1Draft Talon Heavy Hoist Hook.ppt [Compatibility Mode]  

NLE Websites -- All DOE Office Websites (Extended Search)

Most Most hooks designed for heavy hoisting and lifting operations are open-ended devices. Consequently, the load being carried is only as secure as the skill of the operator performing the lift. Any sudden stops, shift or change in direction of the load during operation could result in the potential disengagement of the load from the hook resulting in damage to the cargo or potential injury to the rigging personnel. The locking mechanism of the Talon makes it virtually impossible for the load to slip or drop from the hook. Only when the cargo is safely lowered into its desired position and the locking mechanism is released can the payload be disengaged. The disengagement of the load is also possible through remote means inherent in the design of the device. Remote release of heavy payloads eliminates the need for rigging personnel to manually release the rigging wires or straps from the hoist

424

NEPA COMPLIANCE SURVEY  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7 7 Project lnfonnation Project ntle: TerrVlci RSS Ill Dat e: 11-18-09 DOE Code: 6730.020.71088 Contractor Code: 8067-746 Project Lead : Frank Ingham Project Overview Nill. We reentering an existing well with the rig currently in place on an existing pad and an existing pit. We 1. What are the environmental impacts? will drill one or more directionally drilled laterals. The well will be plugged back when finished or left for a subsequent partner. 2. What is the legal location? 3. What is the duration of the project? The well is the 45-3-X-21 , API#49-025-23507, 2315" FSL & 2323" FWLof Sec 21 , T39N, R7fNV 4. What major equipment will be used If any (work over rig, drilling rig, The test is scheduled to last for approx 4 days. etc.)?

425

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

401 - 8410 of 28,905 results. 401 - 8410 of 28,905 results. Download CPS 8.1 Hoisting and Rigging, 2/25/2000 The objective of this surveillance is to examine hoisting and rigging operations to ensure that safe equipment and work practices are being used. The surveillance includes verification that... http://energy.gov/hss/downloads/cps-81-hoisting-and-rigging-2252000 Download EIS-0375: DOE Notice of Availability of the Draft Environmental Impact Statement Disposal of Greater-Than-Class C Low-Level Radioactive Waste http://energy.gov/nepa/downloads/eis-0375-doe-notice-availability-draft-environmental-impact-statement Download EIS-0391: Notice to Extend Scoping Period Tank Closure and Waste Management for the Hanford Site, Richland, WA http://energy.gov/nepa/downloads/eis-0391-notice-extend-scoping-period

426

NEPA COMPLIANCE SURVEY  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0 0 Project lnfonnation Project Title: Openhole Logging Well Date: 2-8-2010 DOE Code: 6730-020-51135 Contractor Code: TBD Project Lead: Brian Black Project Overview This project will use the drilling rig and associated equipment to drill a well to 5400 feet that will be 1. What are the environmental impacts? designated for Openhole logging. The environmental impads include possible spills on location of drilling fluids or downhole fluids, minor excavation may be necessary in a pre-existing lined pit, and some earthwork to prepare the location for the drilling rig. 2. What is the legal location? This project will take place on the 61-2-TpX-10 well location (189' FNL, 1895' FEL Section 15,TWP38N, RNG78W). 3. What is the duration of the projed? This project is expected have a duration of 4 weeks (2 weeks of moving the rig, and 2 weeks of drilling,

427

NEPA COMPLIANCE SURVEY Project Information Project Title: Liner Drilling Date:  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Liner Drilling Date: Liner Drilling Date: 4-5-10 DOE Code: 71092 Cont ractor Code: 8067-766 Project Lead: Frank Ingham Project Overview Nothing out of the ordinary for drilling an existing location 1. What are the environmental impacts? NE SW Sec 21 , T39N, R78W (45-3-X-21 well) 2. What is the legal location? 3. What is the duration of the project? Approximately a week 4 . What major equipment will be used if any (work over rig, drilling rig, Drilling Rig etc.)? Will Drill out of 9 5/8 caslng with liner drillng assembly. After drilling approximately 750 to 1000 ft, will test liner hanging assembly set and retrieve multiple times. The table b elow is to be completed by the Project Lead and reviewed by the Environmental Specialis t and the DOE NEPA Compliance Officer. NOTE: If Change of Scope occurs, Project Lead must submit a new NEPA Compliance Survey a

428

Fisheries Management Group  

E-Print Network (OSTI)

Programme 8 of the 2004/05 Fisheries Science Partnership investigated aspects of the selectivity of certain types of trawl gear used in the Irish Sea. The western Irish Sea study reported here examined the catch rate and size composition of whitefish taken by three different types of Nephrops trawlers operating out of Northern Ireland. The study also provided information to help design a forthcoming FIFG project examining selectivity of Nephrops trawls. The vessels chartered to carry out the programme were the FV Rhodanna, a single-rig trawler over 12m long, the FV Margreta-M, a single-rig trawler under 12m long, and the FV Golden Bells II, a twin-rig trawler. The three vessels operated at different

Programme Gear; Irish Sea; Part Western; Irish Sea Nephrops; Mike Armstrong; John Cotter; John Dann; Andrew Revill; Kevin Sullivan; Greg Foster; Pieter-jan Schön; Richard Briggs; Dave Bevan

2004-01-01T23:59:59.000Z

429

High Pressure Coolant Injection (HPCI) System Risk-Based Inspection Guide for Browns Ferry Nuclear Power Station  

Science Conference Proceedings (OSTI)

The High Pressure Coolant Injection (HPCI) system has been examined from a risk perspective. A System Risk-Based Inspection Guide (S-RIG) has been developed as an aid to HPCI system inspections at the Browns Ferry Nuclear Power Plant, Units 1, 2 and 3. The role of. the HPCI system in mitigating accidents is discussed in this S-RIG, along with insights on identified risk-based failure modes which could prevent proper operation of the system. The S-RIG provides a review of industry-wide operating experience, including plant-specific illustrative examples to augment the PRA and operational considerations in identifying a catalogue of basic PRA failure modes for the HPCI system. It is designed to be used as a reference for routine inspections, self-initiated safety system functional inspections (SSFIs), and the evaluation of risk significance of component failures at the nuclear power plant.

Wong, S.; DiBiasio, A.; Gunther, W. [Brookhaven National Lab., Upton, NY (United States)

1993-09-01T23:59:59.000Z

430

In-Situ Creep Testing Capability for the Advanced Test Reactor  

Science Conference Proceedings (OSTI)

An instrumented creep testing capability is being developed for specimens irradiated in Pressurized Water Reactor (PWR) coolant conditions at the Advanced Test Reactor (ATR). The test rig has been developed such that samples will be subjected to stresses ranging from 92 to 350 MPa at temperatures between 290 and 370 °C up to at least 2 dpa (displacement per atom). The status of Idaho National Laboratory (INL) efforts to develop the test rig in-situ creep testing capability for the ATR is described. In addition to providing an overview of in-pile creep test capabilities available at other test reactors, this paper reports efforts by INL to evaluate a prototype test rig in an autoclave at INL’s High Temperature Test Laboratory (HTTL). Initial data from autoclave tests with 304 stainless steel (304 SS) specimens are reported.

B. G. Kim; J. L. Rempe; D. L. Knudson; K. G. Condie; B. H. Sencer

2012-09-01T23:59:59.000Z

431

Movement and Injury Rates for Three Life Stages of Spring Chinook Salmon Oncorhynchus Tshawytscha : A Comparison of Submerged Orifices and an Overflow Weir for Fish Bypass in a Modular Rotary Drum Fish Screen : Annual Report 1995.  

DOE Green Energy (OSTI)

The Pacific Northwest National Laboratory (PNNL) evaluated the effectiveness of 6-in. and 2-in. submerged orifices, and an overflow weir for fish bypass at a rotary drum fish screening facility. A modular drum screen built by the Washington Department of Fish and Wildlife (WDFW) was installed at PNNL`s Aquatic Ecology research laboratory in Richland, Washington. Fry, subyearlings, and smolts of spring chinook salmon (Oncorhynchus tshawyacha) were introduced into the test system, and their movement and injury rates were monitored. A total of 33 tests (100 fish per test) that lasted from 24 to 48 hr were completed from 1994 through 1995. Passage rate depended on both fish size and bypass configuration. For fry/fingerling spring chinook salmon, there was no difference in passage rate through the three bypass configurations (2-in. orifice, 6-in. orifice, or overflow weir). Subyearlings moved sooner when the 6-in. orifice was used, with more than 50% exiting through the fish bypass in the first 8 hr. Smolts exited quickly and preferred the 6-in. orifice, with over 90% of the smolts exiting through the bypass in less than 2 hr. Passage was slightly slower when a weir was used, with 90% of the smolts exiting in about 4 hr. When the 2-in. orifice was used in the bypass, 90% of the smolts did not exit until after 8 hr. In addition, about 7% of the smolts failed to migrate from the forebay within 24 hr, indicating that smolts were significantly delayed when the 2-in. orifice was used. Few significant injuries were detected for any of the life stages. However, light descaling occurred on about 15% of chinook salmon smolts passing through the 2-in. orifice. Although a single passage through the orifice did not appear to cause significant scale loss or other damage, passing through several screening facilities with 2-in. orifices could cause cumulative injuries.

Abernethy, C. Scott; Neitzel, Duane A.; Mavros, William V.

1996-03-01T23:59:59.000Z

432

PowerPoint Presentation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Department of Energy Department of Energy Transportation External Working Group (TEC) EDWARDS MOVING & RIGGING, INC. Heavy Transport Presentation Presented By What kind of projects do we do? Heavy Transport Heavy Rigging Focus today is Heavy Transport Focus today is Heavy Transport Turbine Generator Transformer Boilers Vessel Press Bridge Duct work Railroad Engine Tank Relocation 440T Building Solid Masonry Even a building facade "These guys can move anything" Pressurizer RA Movement of Hazardous Cargo Major Plant Components & Casks Cask Movement Shipment by Road Shipment by Road Shipment by Railroad Shipments by Barge What makes Transport Contactors Suited for these projects? Complete Package *Engineering *Planning *State-of-the-art-equipment

433

Different Sets of Channels in the Instructions Series of Rdzogs chen  

E-Print Network (OSTI)

snang srid snod bcud 'khor 'das thams cad rig pa'i rang snang du shar ba la /thabs ma 'gags par snang ba yab la /shes rab mi 'dzin par stong pa yum dang gnyis med du sbyar bas /gang snang rig pa'i grogs su rang shar te /: “Thus, method, i... : /khyad par ka ti shel sbugs can //dar kar snal ma phra la 'khril //'di bzi'i nang na 'od dang zer //thig le thig phran ye shes rlung //rgyu bas ye shes snang ba ston //'od rtsa'i rang Revue d’Etudes Tibétaines 32 where they serve as usual as carriers...

Scheidegger, Daniel

2007-01-01T23:59:59.000Z

434

Nondestructive evaluation of ceramic matrix composite combustor components.  

SciTech Connect

Combustor liners fabricated from a SiC/SiC composite were nondestructively interrogated before and after combustion rig testing. The combustor liners were inspected by X-ray, ultrasonic and thermographic techniques. In addition, mechanical test results were obtained from witness coupons, representing the as-manufactured liners, and from coupons machined from the components after combustion exposure. Thermography indications were found to correlate with reduced material properties obtained after rig testing. Microstructural examination of the SiC/SiC liners revealed the thermography indications to be delaminations and damaged fiber tows.

Sun, J. G.; Verrilli, M. J.; Stephan, R.; Barnett, T. R.; Ojard, G.

2002-11-08T23:59:59.000Z

435

Smaller Footprint Drilling System for Deep and Hard Rock Environments; Feasibility of Ultra-High-Speed Diamond Drilling  

SciTech Connect

The two phase program addresses long-term developments in deep well and hard rock drilling. TerraTek believes that significant improvements in drilling deep hard rock will be obtained by applying ultra-high rotational speeds (greater than 10,000 rpm). The work includes a feasibility of concept research effort aimed at development that will ultimately result in the ability to reliably drill 'faster and deeper' possibly with smaller, more mobile rigs. The principle focus is on demonstration testing of diamond bits rotating at speeds in excess of 10,000 rpm to achieve high rate of penetration (ROP) rock cutting with substantially lower inputs of energy and loads. The significance of the 'ultra-high rotary speed drilling system' is the ability to drill into rock at very low weights on bit and possibly lower energy levels. The drilling and coring industry today does not practice this technology. The highest rotary speed systems in oil field and mining drilling and coring today run less than 10,000 rpm - usually well below 5,000 rpm. This document provides the progress through two phases of the program entitled 'Smaller Footprint Drilling System for Deep and Hard Rock Environments: Feasibility of Ultra-High-Speed Diamond Drilling' for the period starting 30 June 2003 and concluding 31 March 2009. The accomplishments of Phases 1 and 2 are summarized as follows: (1) TerraTek reviewed applicable literature and documentation and convened a project kick-off meeting with Industry Advisors in attendance (see Black and Judzis); (2) TerraTek designed and planned Phase I bench scale experiments (See Black and Judzis). Improvements were made to the loading mechanism and the rotational speed monitoring instrumentation. New drill bit designs were developed to provided a more consistent product with consistent performance. A test matrix for the final core bit testing program was completed; (3) TerraTek concluded small-scale cutting performance tests; (4) Analysis of Phase 1 data indicated that there is decreased specific energy as the rotational speed increases; (5) Technology transfer, as part of Phase 1, was accomplished with technical presentations to the industry (see Judzis, Boucher, McCammon, and Black); (6) TerraTek prepared a design concept for the high speed drilling test stand, which was planned around the proposed high speed mud motor concept. Alternative drives for the test stand were explored; a high speed hydraulic motor concept was finally used; (7) The high speed system was modified to accommodate larger drill bits than originally planned; (8) Prototype mud turbine motors and the high speed test stand were used to drive the drill bits at high speed; (9) Three different rock types were used during the testing: Sierra White granite, Crab Orchard sandstone, and Colton sandstone. The drill bits used included diamond impregnated bits, a polycrystalline diamond compact (PDC) bit, a thermally stable PDC (TSP) bit, and a hybrid TSP and natural diamond bit; and (10) The drill bits were run at rotary speeds up to 5500 rpm and weight on bit (WOB) to 8000 lbf. During Phase 2, the ROP as measured in depth of cut per bit revolution generally increased with increased WOB. The performance was mixed with increased rotary speed, with the depth cut with the impregnated drill bit generally increasing and the TSP and hybrid TSP drill bits generally decreasing. The ROP in ft/hr generally increased with all bits with increased WOB and rotary speed. The mechanical specific energy generally improved (decreased) with increased WOB and was mixed with increased rotary speed.

TerraTek, A Schlumberger Company

2008-12-31T23:59:59.000Z

436

Stabilizing geometry for hydrodynamic rotary seals  

DOE Patents (OSTI)

A hydrodynamic sealing assembly including a first component having first and second walls and a peripheral wall defining a seal groove, a second component having a rotatable surface relative to said first component, and a hydrodynamic seal comprising a seal body of generally ring-shaped configuration having a circumference. The seal body includes hydrodynamic and static sealing lips each having a cross-sectional area that substantially vary in time with each other about the circumference. In an uninstalled condition, the seal body has a length defined between first and second seal body ends which varies in time with the hydrodynamic sealing lip cross-sectional area. The first and second ends generally face the first and second walls, respectively. In the uninstalled condition, the first end is angulated relative to the first wall and the second end is angulated relative to the second wall. The seal body has a twist-limiting surface adjacent the static sealing lip. In the uninstalled condition, the twist-limiting surface is angulated relative to the peripheral wall and varies along the circumference. A seal body discontinuity and a first component discontinuity mate to prevent rotation of the seal body relative to the first component.

Dietle, Lannie L. (Houston, TX); Schroeder, John E. (Richmond, TX)

2010-08-10T23:59:59.000Z

437

Rotary steerable motor system for underground drilling  

Science Conference Proceedings (OSTI)

A preferred embodiment of a system for rotating and guiding a drill bit in an underground bore includes a drilling motor and a drive shaft coupled to drilling motor so that drill bit can be rotated by the drilling motor. The system further includes a guidance module having an actuating arm movable between an extended position wherein the actuating arm can contact a surface of the bore and thereby exert a force on the housing of the guidance module, and a retracted position.

Turner, William E. (Durham, CT); Perry, Carl A. (Middletown, CT); Wassell, Mark E. (Kingwood, TX); Barbely, Jason R. (Middletown, CT); Burgess, Daniel E. (Middletown, CT); Cobern, Martin E. (Cheshire, CT)

2010-07-27T23:59:59.000Z

438

Continuous Flow Differential Pressure Rotary Transport ...  

This patent-pending active material transport system design concept provides solutions to several process challenges associated with moving materials ...

439

Advanced turbine systems program conceptual design and product development. Quarterly report, November 1, 1996--January 31, 1997  

SciTech Connect

The confirmation for the contract modification was received on February 19, 1997. All reports reflect this modification at present. Technical highlights for the reporting period are: first results on steam oxidation behavior of super alloys in steam environment have been achieved; and the tests on TBC evaluation in high thermal gradients could be started. The turbine test rig hardware is progressing well.

1997-05-01T23:59:59.000Z

440

Bulletin of Tibetology: Volume 39 Number 2 Editorial  

E-Print Network (OSTI)

on the Institute's web-site under publications (www.tibetology.com). In the last issue, vol. 39 (1), we published an article by Martin J Boord entitled A Pilgrim's guide to the Hidden Land of Sikkim proclaimed as a treasure by Rig 'dzin rgod kyi Idem 'phru can...

Balikci-Denjongpa, Anna

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Ford/ERDA continuously variable transmission. Phase I. Transmission design. Progress report No. 9, January 1--March 31, 1976  

DOE Green Energy (OSTI)

Progress is reported for a research program to analyze and design a Forster traction drive infinitely variable transmission for improving passenger car fuel economy. Many disc configurations were analyzed using a finite element analysis computer program, and performance and fuel economy estimates were made from a simulation model. An initial transmission layout design was completed, and test rig components were inspected and assembled. (PMA)

Stockton, T.R.

1976-01-01T23:59:59.000Z

442

Microsoft Word - S05827_WCR_Final.doc  

Office of Legacy Management (LM)

HTH-1RC Data HTH-1RC Data This page intentionally left blank U.S. Department of Energy Well Completion Report for CAU 443 CNTA December 2009 Doc. No. S05827 Page E-1 Table E-1. HTH-1RC_Chronology Date Time Depth (ft bgs) Activity 05/26/09 15:45 - 21:00 NA DH rig (LK17) arrives on site, rig is inspected, tire replaced, and rig was moved to HTH-1 pad. 05/26/09 23:30 NA Fishing tool was run 180 ft down HTH-1 and the bladder pump was retrieved. 05/27/09 01:00 NA Rig is moved off HTH-1 and goes to UC-1-P-1S 06/04/09 21:40 NA Crane set up at HTH-1 to begin running in BQ tremie pipe. 06/05/09 03:10 NA Finish tripping in BQ tremie pipe to 2,700 ft. 06/05/09 06:55 NA Finish tripping in shallow piezometer string to a depth of 1,038.6 ft. 06/05/09 09:20 NA Finish tripping in deep piezometer string to a depth of 1,958.6 ft.

443

Procedure for Planning and Conducting  

NLE Websites -- All DOE Office Websites (Extended Search)

Lift Plan Procedure Lift Plan Procedure Stanford Synchrotron Radiation Laboratory Lead Author __________________________________ Date 07/13/2005___________ David A. Ernst Mechanical Service Group Approvals: __________________ Date _____________________ Matt Padilla SSRL Safety Officer __________________ Date _____________________ Robert Hettel Accelerator System Department Head __________________ Date _____________________ Piero Pianetta Beam Line System Department Head Hoist and Rigging Panel Member _______________________________________ Date ______________________

444

Advanced turbine technology applications project (ATTAP): Hybrid vehicle turbine engine technology support (HVTE-TS): Annual report, 1993-1994  

DOE Green Energy (OSTI)

This is the sixth of a series of reports documenting work performed on the ATTAP/HVTETS. This is a combined report to cover work performed in both 1993 and 1994. Progress is reported on ceramic component design and characterization, powertrain development, component rig testing and performance and durability testing.

NONE

1996-03-01T23:59:59.000Z

445

V THE BEAT IS GETTING STRONGER: low frequency modulated wind turbine sound  

E-Print Network (OSTI)

turbine research rig benefits from both single layered deposited thin film sensors and two- layered gauges used to test a single HP turbine stage. The facility was recently extended to 1.5 turbine stages in axial turbines. A set of phase-locked LDA measurements clearly show the extent of tip vortical flow near

Groningen, Rijksuniversiteit

446

WIND AND WATER POWER PROGRAM BUILDINGACLEAN  

E-Print Network (OSTI)

turbine research rig benefits from both single layered deposited thin film sensors and two- layered gauges used to test a single HP turbine stage. The facility was recently extended to 1.5 turbine stages in axial turbines. A set of phase-locked LDA measurements clearly show the extent of tip vortical flow near

447

ATTAP: Advanced Turbine Technology Applications Project. Annual report, 1991  

DOE Green Energy (OSTI)

Purpose of ATTAP is to bring the automotive gas turbine engine to a technology state at which industry can make commercialization decisions. Activities during the past year included test-bed engine design and development, ceramic component design, materials and component characterization, ceramic component process development and fabrication, ceramic component rig testing, and test-bed engine fabrication and testing.

Not Available

1992-12-01T23:59:59.000Z

448

Abbreviations and Symbols  

Science Conference Proceedings (OSTI)

...embrittlement ln natural logarithm (base e ) LNG liquefied natural gas log common logarithm (base 10) LPR linear polarization resistance LSI Langelier saturation index LTCTF long-term corrosion test facility LTHC low-temperature hot corrosion LVBR low-velocity atmospheric pressure burner rig m...

449

Practical applications of a drilling data center  

SciTech Connect

Tenneco Oil is using a real-time drilling-data acquisition, telemetry, data base, and applications-program system for Gulf of Mexico operations. The system provides for data acquisition in real time from commercially available logging units. The data are transmitted into a central office onshore via microwave or satellite telemetry links. Up to 352 drilling parameters are transmitted from each computerized logging unit and archived in the data base every 20 sec. Parameters can include measurement-while-drilling (MWD) data as well as mud-logging data. Applications programs utilizing these parameters are available in the central site data center (CSDC) and in locations throughout Tenneco's facilities in Lafayette, La. Access to the CSDC and its computing power is also available on the offshore rig. Backup surveillance of critical drilling parameters is provided through alarms and continuous monitoring of the parameters, thus providing for a safer operation. Rig efficiency has also been improved through analysis of the data and comparison of the data between various rig operations and rigs. Both tangible and intangible cost savings are discussed.

Graff, R.L.; Segrest, R.P.

1986-05-19T23:59:59.000Z

450

Flow and Plate Motion in Compressor Valves  

E-Print Network (OSTI)

Industry,... Mission: #12;15 Group Engineering Fluid Dynamics Rotating-flow machines ­ Centrifugal pumps Machines · pumps · wind turbines · compressors · propellers EFD-FLOW #12;17 Engineering Fluid Dynamics (HWA, visualisation) · ball-on-disc test rig · Starling Resistor ( lung tubes) · CFD-lab servers, PC

Twente, Universiteit

451

Page 1 of 1 BSD-CS-2041  

E-Print Network (OSTI)

, and components known to have been misrepresented include, but are not limited to, fasteners; hoisting, rigging, and lifting equipment; cranes; hoists; valves; pipe and fittings; electrical equipment and devices; plate, bar or obliterated. Terminal configuration and hardware shall not have been altered or modified from the original

Pennycook, Steve

452

Health and Safety Plan for NSTX Upgrade Project Tasks  

E-Print Network (OSTI)

and the DOE Hoisting and Rigging Manual. Herein is our site specific Health and Safety Plan for the work-vessel passive plates hardware. Rev 1 2 11/9111 #12;3.0 RESPONSmILITIES, AUTHORITIES, COMMUNICATIONS The Work

Princeton Plasma Physics Laboratory

453

Physics and the Search for Hydrocarbons  

E-Print Network (OSTI)

Historical Note from 1979 #12;In 1979, US imported 30% of its oil supply. In 2010, US imported 61% of its oil photo · Anisotropic properties: electrical resistivity, fluid flow (permeability), acoustic propagation, creates pressure pulses Pressure waves travel inside drill pipe from downhole to rig Low data-rates: 1 ­24

Dai, Pengcheng

454

Design of a Transonic Research Turbine Facility Ruolong Ma*  

E-Print Network (OSTI)

and performance of modern gas-turbine engines. A detailed address of the various opportunities for flow control throughout the gas-turbine engine in terms of their impact on each engine component was given by Lord et al.1 in the new Advanced Performance Gas Turbine Laboratory at the University of Notre Dame. II. Turbine Rig

Morris, Scott C.

455

An overproduce-and-choose strategy to create classifier ensembles with tuned SVM parameters applied to real-world fault diagnosis  

Science Conference Proceedings (OSTI)

We present a supervised learning classification method for model-free fault detection and diagnosis, aiming to improve the maintenance quality of motor pumps installed on oil rigs. We investigate our generic fault diagnosis method on 2000 examples of ... Keywords: classifier ensemble, fault diagnosis, feature extraction, feature selection, multi-label classification, support vector machine

Estefhan Dazzi Wandekokem; Flávio M. Varejão; Thomas W. Rauber

2010-11-01T23:59:59.000Z

456

Bureau of Economic Geology, The University of Texas at Austin "It was a dark and stormy night..."  

E-Print Network (OSTI)

Nuclear Other renewables Petroleum coke Other gases and other fuels Coal Petroleum Hydro ChangeDetection and advanced stimulation ­ Slow decline curves ­ Reduce drilling (fewer rigs, lower costs, smaller footprint, CEE/BEG/JSG/UT Not All Producers are the Same $10 $12 10% Return U.S. 2010 Cash Operating Costs

Texas at Austin, University of

457

UNITED STATES Calendar Year 2006  

E-Print Network (OSTI)

Nuclear Other renewables Petroleum coke Other gases and other fuels Coal Petroleum Hydro ChangeDetection and advanced stimulation ­ Slow decline curves ­ Reduce drilling (fewer rigs, lower costs, smaller footprint, CEE/BEG/JSG/UT Not All Producers are the Same $10 $12 10% Return U.S. 2010 Cash Operating Costs

US Army Corps of Engineers

458

P U R S U I T A N D P R O M O T I O N O F S C I E N C E he Council of Scientific and Industrial  

E-Print Network (OSTI)

Nuclear Other renewables Petroleum coke Other gases and other fuels Coal Petroleum Hydro ChangeDetection and advanced stimulation ­ Slow decline curves ­ Reduce drilling (fewer rigs, lower costs, smaller footprint, CEE/BEG/JSG/UT Not All Producers are the Same $10 $12 10% Return U.S. 2010 Cash Operating Costs

Srinivasan, N.

459

Workload analysis and scheduling policies for a document processing centre  

E-Print Network (OSTI)

This thesis is the result of a six-month internship at the Steel Stock Department of Keppel FELS Singapore, a company which is involved in the design and construction of oil-rigs. The primary objective of this project is ...

Tan, Chin Jiat

2006-01-01T23:59:59.000Z

460

Suslick Group Responsibilities Effective 07/19/2011  

E-Print Network (OSTI)

, and at each Group Cleanup, (1) change oil in pump every 6 months, (2) clean bulkhead filters and (3) calibrate the manifold volume. Catalyst Rig: Routine maintenance. IMPORTANT: CHANGE PUMP OIL ON THE FIRST MONDAY OF EVERY as needed; IMPORTANT: CHANGE ANTECHAMBER PUMP OIL AFTER REGENERATION. Instruct new users. Every Monday

Suslick, Kenneth S.

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

5/10/10 7:21 AMDaily Briefing: Thurs. | The dome stretch | MNN -Mother Nature Network Page 1 of 5http://www.mnn.com/home-blog/green-news-roundup/blogs/daily-briefing-thurs-55  

E-Print Network (OSTI)

, being carried on a barge) is designed to siphon up the leaking oil and pump it to barges on the surface: A four-story, 98-ton "containment dome" has arrived at the site of a gushing oil well in the Gulf a new relief well to plug the oil geyser -- which began erupting after a BP-owned oil rig exploded

Hazen, Terry

462

Potential of Malaysian activated carbon in dual purpose adsorption system  

Science Conference Proceedings (OSTI)

The adsorption capability of some locally produced activated charcoal (coconut shell) samples with methanol were taken under laboratory conditions. An experimental test rig was set up; data obtained from the experiments were fitted to Dubinin-Radushkevitch ... Keywords: Malaysian activated carbon, adsorption properties, coefficient of performance (COP), dual purpose system

M. A. Alghoul; M. Y. Sulaiman; K. Sopian; M. Yahya; Azami Zaharim

2008-11-01T23:59:59.000Z

463

November 16, 2010 Rep.-Elect West's Drilling Stance --and Refusal to Back Down --  

E-Print Network (OSTI)

into office. Days after the Deepwater Horizon oil rig began spewing crude into the Gulf of Mexico, Florida at preventing" more oil disasters, West finished: "Any person permanently taking oil exploration off the table is closing the door for an energy independent United States, thus further enabling our enemies to hold us

Belogay, Eugene A.

464

Approved for public release; distribution is unlimited. ERDC/EL TN-11-4  

E-Print Network (OSTI)

the well was successfully capped (OSAT 2010). This is comparable in magnitude to previous oil spills in U.S due to releases of crude oil from tankers, offshore platforms, drilling rigs and wells. Spills was one of four large oil spills occurring along U.S. coastlines from 1976 to 2010. Depending

US Army Corps of Engineers

465

Automation ensures safety, extends production  

Science Conference Proceedings (OSTI)

This paper reviews some current improvements in offshore platform safety as a result of new regulations. In response to Norwegian Petroleum Directorate regulations limiting personnel on the rig floor, Weatherford Norway has developed a casing modem with remote-controlled power tongs. This paper reviews the various automated systems for handling drill pipes and joints on offshore platforms and how they work.

Perdue, J.M.

1996-06-01T23:59:59.000Z

466

Autonomous Measurements of Sea Surface Temperature Using In Situ Thermal Infrared Data  

Science Conference Proceedings (OSTI)

In situ and autonomous measurements of sea surface temperature (SST) have been performed with a thermal infrared radiometer mounted on a fixed oil rig. The accuracy limit was established at ±0.3 K for these SST measurements in order to meet the ...

Raquel Niclòs; Vicente Caselles; César Coll; Enric Valor; Eva Rubio

2004-04-01T23:59:59.000Z

467

Evaluation and silicon nitride internal combustion engine components  

DOE Green Energy (OSTI)

The feasibility of silicon nitride (Si[sub 3]N[sub 4]) use in internal combustion engines was studied by testing three different components for wear resistance and lower reciprocating mass. The information obtained from these preliminary spin rig and engine tests indicates several design changes are necessary to survive high-stress engine applications. The three silicon nitride components tested were valve spring retainers, tappet rollers, and fuel pump push rod ends. Garrett Ceramic Components' gas-pressure sinterable Si[sub 3]N[sub 4] (GS-44) was used to fabricate the above components. Components were final machined from densified blanks that had been green formed by isostatic pressing of GS-44 granules. Spin rig testing of the valve spring retainers indicated that these Si[sub 3]N[sub 4] components could survive at high RPM levels (9,500) when teamed with silicon nitride valves and lower spring tension than standard titanium components. Silicon nitride tappet rollers showed no wear on roller O.D. or I.D. surfaces, steel axles and lifters; however, due to the uncrowned design of these particular rollers the cam lobes indicated wear after spin rig testing. Fuel pump push rod ends were successful at reducing wear on the cam lobe and rod end when tested on spin rigs and in real-world race applications.

Voldrich, W. (Allied-Signal Aerospace Co., Torrance, CA (United States). Garrett Ceramic Components Div.)

1992-04-01T23:59:59.000Z

468

Evaluation and silicon nitride internal combustion engine components. Final report, Phase I  

DOE Green Energy (OSTI)

The feasibility of silicon nitride (Si{sub 3}N{sub 4}) use in internal combustion engines was studied by testing three different components for wear resistance and lower reciprocating mass. The information obtained from these preliminary spin rig and engine tests indicates several design changes are necessary to survive high-stress engine applications. The three silicon nitride components tested were valve spring retainers, tappet rollers, and fuel pump push rod ends. Garrett Ceramic Components` gas-pressure sinterable Si{sub 3}N{sub 4} (GS-44) was used to fabricate the above components. Components were final machined from densified blanks that had been green formed by isostatic pressing of GS-44 granules. Spin rig testing of the valve spring retainers indicated that these Si{sub 3}N{sub 4} components could survive at high RPM levels (9,500) when teamed with silicon nitride valves and lower spring tension than standard titanium components. Silicon nitride tappet rollers showed no wear on roller O.D. or I.D. surfaces, steel axles and lifters; however, due to the uncrowned design of these particular rollers the cam lobes indicated wear after spin rig testing. Fuel pump push rod ends were successful at reducing wear on the cam lobe and rod end when tested on spin rigs and in real-world race applications.

Voldrich, W. [Allied-Signal Aerospace Co., Torrance, CA (United States). Garrett Ceramic Components Div.

1992-04-01T23:59:59.000Z

469

Fireside Corrosion USC Steering  

SciTech Connect

Oxy-Fuel Fireside Research goals are: (1) Determine the effect of oxy-fuel combustion on fireside corrosion - (a) Flue gas recycle choice, Staged combustion ramifications, (c) JCOAL Collaboration; and (2) Develop methods to use chromia solubility in ash as an 'ash corrosivity' measurement - (a) Synthetic ashes at first, then boiler and burner rig ashes, (b) Applicable to SH/RH conditions.

G. R. Holcomb; J. Tylczak

2011-09-07T23:59:59.000Z

470

Fireside Corrosion  

Science Conference Proceedings (OSTI)

Oxy-fuel fireside research goals are: (1) determine the effect of oxyfuel combustion on fireside corrosion - flue gas recycle choice, staged combustion ramifications; and (2) develop methods to use chromia solubility in ash as an ash corrosivity measurement - synthetic ashes at first, then boiler and burner rig ashes.

Holcomb, Gordon

2011-07-14T23:59:59.000Z

471

OEIM 210. Industrial Mechanics III 4 cr. Air compressors, sliding surface bearings, boiler maintenance, boiler  

E-Print Network (OSTI)

OEIM 210. Industrial Mechanics III 4 cr. Air compressors, sliding surface bearings, boiler maintenance, boiler tube repairs, basic arc and gas welding, measurement tools, gauge glass maintenance, heat by employer and instructor on boiler inspection and cleaning, centrifugal pumps, basic rigging, piping

Castillo, Steven P.

472

851 S.W. Sixth Avenue, Suite 1100 Steve Crow 503-222-5161 Portland, Oregon 97204-1348 Executive Director 800-452-5161  

E-Print Network (OSTI)

tightened up. Natural gas rig count has decreased.g g Price competition between coal and natural gas forecast of natural gas prices in the near-term The oil prices has been increased Coal prices are within SUBJECT: Natural gas price forecast update At the June Council meeting we presented a draft update

473

ORIGINAL ARTICLE Yield prediction for seamless tubing processes  

E-Print Network (OSTI)

and natural gas exploration and production, fluid transmission, and the construction indus- try. A market survey of the American steel industry indicated that the American oil rig count experienced a decline an increasing demand for seamless tubing for gas and oil production [1]. Steel tubes are made by several

Huang, Samuel H.

474

The Public Health Implications of Marcellus Shale Activities  

E-Print Network (OSTI)

INCIDENT #12;#12;#12;Implications of the Gulf Oil Spill to Marcellus Shale Activities - EnvironmentalThe Public Health Implications of Marcellus Shale Activities Bernard D. Goldstein, MD Department using Data.FracTracker.org. #12;Drilling Rig in Rural Upshur County, WV Source: WVSORO, Modern Shale Gas

Sibille, Etienne

475

Research Technician for Experimental Geomechanics Laboratories ExxonMobil Upstream Research Company has an immediate opening for a Research  

E-Print Network (OSTI)

instrumentation for load, pressure, and strain measurements and computer control software. Preparation of rock: load frames, hydraulic actuators, high pressure/high temperature pumps and pressure vessels, electronic specimen using coring rigs, saws and grinders. Analysis and manipulation of basic data spreadsheets

Evans, Paul G.

476

WRITTEN STATEMENT OF JANE LUBCHENCO, Ph.D.  

E-Print Network (OSTI)

to monitor the effects of the oil spill on Louisiana's coastal marshes and fishery species. · NOAA's National ON "OUTER CONTINENTAL SHELF OIL AND GAS STRATEGY AND IMPLICATIONS OF THE DEEPWATER HORIZON RIG EXPLOSION oil spill. My name is Dr. Jane Lubchenco and I am the Under Secretary of Commerce for Oceans

477

OCEAN DRILLING PROGRAM LEG 171B PRELIMINARY REPORT  

E-Print Network (OSTI)

at these adjacent holes. Well-developed ash zones in Core 136-842A-1H contain fresh glass as well as minerals of high-viscosity mud was pumped and circulated out. It was decided to trip the drill string and rig up

478

Top Engineers to Investigate Cause of Oil by Lauren Schenkman on July 13, 2010 6:02 PM |  

E-Print Network (OSTI)

Top Engineers to Investigate Cause of Oil Spill by Lauren Schenkman on July 13, 2010 6:02 PM | Investigations into the gulf oil disaster are multiplying. The National Academy of Engineering (NAE and industry engineers to take a technical look into the causes of the Deepwater Horizon rig explosion and oil

Southern California, University of

479

Volume 31 Number 5 March 6, 1985 Dan Spinner  

E-Print Network (OSTI)

-community relations. In 1982 he developed a course in management of human services at the University of Michigan. Mr off-shore construction begins. "Right now, before oil rigs or loading platforms can be built off ,, "What we do is in effecttake the ' laboratory into the field.We get all the necessary information from

Farrell, Anthony P.

480

Liquid Crystal Technique Application for Heat Transfer Investigation in a Fin-Tube Heat Exchanger Element  

Science Conference Proceedings (OSTI)

The use of thermochromic liquid crystal technique (LCT) and true-colour image processing system in heat transfer modelling is described. Experimental procedure, led on rig at Technical University of Gdansk, cover full-field flow patterns in heat exchanger ... Keywords: heat transfer, thermochromic liquid crystals, vortex generator, wind tunnel

M. Wierzbowski; J. Stasiek

2002-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "rigs rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Design of Automation Control System for Water Chillers  

Science Conference Proceedings (OSTI)

Energy crisis led to the recognition that the energy conservation is important. The aim of performance test rig of a water chiller which is introduced in this paper is just for the energy saving. In order to get the better efficiency, a monitoring system ...

Yuhong Sun; Yuying Sun; Junmei Li; Xiaowei Yin

2009-12-01T23:59:59.000Z

482

LIFTING BEAM DESIGN/ANALYSIS FOR THE DATA ACQUISITION AND CONTROL SYSTEM TRAILER  

SciTech Connect

This supporting document details calculations completed to properly design an adjustable lifting beam. The main use of the lifting beam is to hoist the Data Acquisition and Controls Systems (DACS) trailer over a steam line. All design work was completed using the American Institute of Steel Construction, Manual of Steel Construction (AISC, 1989) and Hanford Hoisting and Rigging Manual (WHC, 1992).

MACKEY TC; BENEGAS TR

1993-03-15T23:59:59.000Z

483

Master Thesis -FS 2014 Focus on Energy, Flow  

E-Print Network (OSTI)

of a Gas Injection and Measurement System for RIGI Centrifugal compressors are used in power generation. A solution to reach it would be to reduce the speed of sound by changing the gas properties of the working rig with the new gas mixture. (10%) Skills in CAD and LabVIEW are useful. You should be creative

Daraio, Chiara

484

Word Pro - Untitled1  

U.S. Energy Information Administration (EIA) Indexed Site

Years, 1949-2011 (Number of Rigs) Year By Site By Type Total 1 Onshore Offshore Crude Oil Natural Gas 1949 NA NA NA NA 2,017 1950 NA NA NA NA 2,154 1955 NA NA NA NA 2,686 1960...

485

Open Access  

E-Print Network (OSTI)

Research article Induction of apoptosis by the retinoid inducible growth regulator RIG1 depends on the NC motif in HtTA cervical cancer cells Fu-Ming Tsai1,2, Rong-Yaun Shyu3, Su-Ching Lin1, Chang-Chieh Wu4 and

Shun-yuan Jiang; Chieh Wu; Shun-yuan Jiang

2009-01-01T23:59:59.000Z

486

What is the Issue? The Marcellus Shale is a geologic shale bed that extends across much  

E-Print Network (OSTI)

What is the Issue? The Marcellus Shale is a geologic shale bed that extends across much of the Marcellus Shale. Energy companies plan to nearly double the number of drilling rigs by the end of the year, this development illustrates the attractiveness of market proximity and the quality of Marcellus Shale gas

Wang, Z. Jane

487

A peak power tracker for low-power permanent-magnet-synchronous-generator-based wind energy conversion systems  

Science Conference Proceedings (OSTI)

This paper presents the results of experimental investigation of a low-power wind energy conversion system (WECS), based on a permanent-magnet synchronous generator (PMSG) connected directly to the turbine. A test rig was built in order to carry out ... Keywords: hardware-in-the-loop simulation, maximum power point tracking, optimal control, permanent-magnet synchronous generator, wind system

C. Vlad; I. Munteanu; A. I. Bratcu; E. Ceanga

2008-07-01T23:59:59.000Z

488

Study of Catcher Bearings for High Temperature Magnetic Bearing Application  

E-Print Network (OSTI)

The Electron Energy Corporation (EEC) along with National Aeronautics and Space Administration (NASA) in collaboration with Vibration Control and Electro mechanics Lab (VCEL), Texas A & M University, College Station, TX are researching on high temperature permanent magnet based magnetic bearings. The magnetic bearings are made of high temperature resistant permanent magnets (up to 1000 degrees F). A test rig has been developed to test these magnetic bearings. The test rig mainly consists of two radial bearings, one axial thrust bearing and two catcher bearings. The test rig that the catcher bearing is inserted in is the first ultra-high temperature rig with permanent magnet biased magnetic bearings and motor. The magnetic bearings are permanent magnet based which is a novel concept. The Graphalloy bearings represent a new approach for ultra-high temperature backup bearing applications. One of the main objectives of this research is to insure the mechanical and electrical integrity for all components of the test rig. Some assemblies and accessories required for the whole assembly need to be designed. The assembly methods need to be designed. The preliminary tests for coefficient of friction, Young's modulus and thermal expansion characteristics for catcher bearing material need to be done. A dynamic model needs to be designed for studying and simulating the rotor drop of the shaft onto the catcher bearing using a finite element approach in MATLAB. The assembly of the test rig was completed successfully by developing assembly fixtures and assembly methods. The components of the test rig were tested before assembly. Other necessary systems like Sensor holder system, Graphalloy press fit system were designed, fabricated and tested. The catcher bearing material (Graphalloy) was tested for coefficient of friction and Young's modulus at room and high temperatures. The rotor drop was simulated by deriving a dynamic model, to study the effect of system parameters like clearance, coefficient of friction, negative stiffness, initial spin speed on system behavior. Increasing the friction increases the backward whirl and decreases the rotor stoppage time. Increasing the clearance reduces the stoppage time and increases the peak bearing force. Increasing the initial spin speed increases the rotor stoppage time. The maximum stress encountered for as built conditions is more than allowable limits.

Narayanaswamy, Ashwanth

2011-05-01T23:59:59.000Z

489

Transport Reactor Facility  

SciTech Connect

The Morgantown Energy Technology Center (METC) is currently evaluating hot gas desulfurization (HGD)in its on-site transport reactor facility (TRF). This facility was originally constructed in the early 1980s to explore advanced gasification processes with an entrained reactor, and has recently been modified to incorporate a transport riser reactor. The TRF supports Integrated Gasification Combined Cycle (IGCC) power systems, one of METC`s advanced power generation systems. The HGD subsystem is a key developmental item in reducing the cost and increasing the efficiency of the IGCC concept. The TRF is a unique facility with high-temperature, high-pressure, and multiple reactant gas composition capability. The TRF can be configured for reacting a single flow pass of gas and solids using a variety of gases. The gas input system allows six different gas inputs to be mixed and heated before entering the reaction zones. Current configurations allow the use of air, carbon dioxide, carbon monoxide, hydrogen, hydrogen sulfide, methane, nitrogen, oxygen, steam, or any mixture of these gases. Construction plans include the addition of a coal gas input line. This line will bring hot coal gas from the existing Fluidized-Bed Gasifier (FBG) via the Modular Gas Cleanup Rig (MGCR) after filtering out particulates with ceramic candle filters. Solids can be fed either by a rotary pocket feeder or a screw feeder. Particle sizes may range from 70 to 150 micrometers. Both feeders have a hopper that can hold enough solid for fairly lengthy tests at the higher feed rates, thus eliminating the need for lockhopper transfers during operation.

Berry, D.A.; Shoemaker, S.A.

1996-12-31T23:59:59.000Z

490

Development and evaluation of a meter for measuring return line fluid flow rates during drilling  

DOE Green Energy (OSTI)

The most costly problem routinely encountered in geothermal drilling is lost circulation, which occurs when drilling fluid is lost to the formation rather than circulating back to the surface. The successful and economical treatment of lost circulation requires the accurate measurement of drilling fluid flow rate both into and out of the well. This report documents the development of a meter for measuring drilling fluid outflow rates in the return line of a drilling rig. The meter employs a rolling counterbalanced float that rides on the surface of the fluid in the return line. The angle of the float pivot arm is sensed with a pendulum potentiometer, and the height of the float is calculated from this measurement. The float height is closely related to the fluid height and, therefore, the flow rate in the line. The prototype rolling float meter was extensively tested under laboratory conditions in the Wellbore Hydraulics Flow Facility; results from these tests were used in the design of the field prototype rolling float meter. The field prototype meter was tested under actual drilling conditions in August and September 1991 at the Long Valley Exploratory Well near Mammoth Lakes, Ca. In addition, the performance of several other commercially available inflow and outflow meters was evaluated in the field. The tested inflow meters included conventional pump stroke counters, rotary pump speed counters, magnetic flowmeters, and an ultrasonic Doppler flowmeter. On the return flow line, a standard paddlemeter, an acoustic level meter, and the prototype rolling float meter were evaluated for measuring drilling fluid outflow rates.

Loeppke, G.E.; Schafer, D.M.; Glowka, D.A.; Scott, D.D.; Wernig, M.D. (Sandia National Labs., Albuquerque, NM (United States)); Wright, E.K. (Ktech Corp., Albuquerque, NM (United States))

1992-06-01T23:59:59.000Z

491

NEPA COMPLIANCE SURVEY Project Information Project Title: Casing Drilling Test  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Casing Drilling Test Casing Drilling Test Date: 5-17-201 1 DOE Code: 6730-020-72000 Contractor Code: 8067-806 Project Lead: Marl< Duletsky Project Overview 1, Brief project description ~nclude The existing 13-1-SX-23 location and entry road will be reworlrig (SST anything that could impact the rig #3). The two existing wells on the location will be capped at ground level, and a new well will be drilled environment] using water based mud. The existing rat I mouse hole on the site will be backfilled. A new 6700 ft3 reserve pit [80' long by 30' wide by 4' deep allowing for 2' of freeboard] will be constructed on location. and a 12 mm 2. Legal location liner will be installed. 3. Duration of the project 4. Major equipment to be used

492

NEPA COMPLIANCE SURVEY  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6 6 Project Information Project Title: Repair flowline at 83-AX-4 Date: 2-17-2010 DOE Code: Contractor Code: Project Lead: Bernard Winfrey Project Overview 1. What are the environmental Repair a flowline leak and test the line at 83-AX-4. Dug up pipeline, will backfill with clean fi ll dirt. Oil impacts? contaminated soil will be hauled to the east side landfarm and clean dirt will be brought in from section 20. 2. What is the legal location? 83-AX-4, N43 17'40.5" w. 10612'46.0" 3. What is the duration of the project? Approximately 2 days 4. What major equipment will be used if any (work over rig, drilling rig, Backhoe with operator and one to three workers. etc.)? The table below is to be completed by the Project Lead and reviewed by the Environmental Specialist and the DOE NEPA

493

MHK Technologies/Hybrid wave Wind Wave pumps and turbins | Open Energy  

Open Energy Info (EERE)

Wind Wave pumps and turbins Wind Wave pumps and turbins < MHK Technologies Jump to: navigation, search << Return to the MHK database homepage Hybrid wave Wind Wave pumps and turbins.jpg Technology Profile Primary Organization Ocean Wave Wind Energy Ltd OWWE Technology Resource Click here Wave Technology Type Click here Point Absorber - Floating Technology Readiness Level Click here TRL 1 3 Discovery Concept Def Early Stage Dev Design Engineering Technology Description 2Wave1Wind The hybrid wave power rig uses two wave converting technologies in addition to wind mills The main system is a pneumatic float in the category of overtopping as Wave Dragon In addition the pneumatic float can house point absorbers The hybrid wave power rig is based on the patented wave energy converter from 2005

494

CX-007139: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

39: Categorical Exclusion Determination 39: Categorical Exclusion Determination CX-007139: Categorical Exclusion Determination Electrical District 2- Electrical District 5 Geological Boring CX(s) Applied: B3.1 Date: 05/16/2011 Location(s): Pinal County, Arizona Office(s): Western Area Power Administration-Desert Southwest Region Western proposes to do geologic borings within our right-of-way near structures 21/5, 22/5, 23/6, 25/4, 26/5, 27/6, 28/5, 29/5 & 30/4 along the existing electrical district (ED) #2-ED5 230-kilovolt transmission line. This project involves accessing each bore hole location with a auger/drill rig and light crew trucks, setting up the drill rig, drilling, collecting soil samples and breaking down the drilling setup. Existing access roads and vehicles such as pickup trucks & crew trucks will be used to bring

495

NEPA COMPLIANCE SURVEY  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

81 81 Project lnfonnation Project Title: CBM Gas Separator Date: 2-23-2010 DOE Code: 6720-020-51131 Contractor Code: Project Lead: Mark Duletsky Project Overview None anticipated, uses producing well on pre-existing location. 1. What are the environmental impacts? 48-2-X-28 Location, 447' FSL. 2495 FWL, SE, SW, Sec. 28, T39N, R78W, Natrona County. Wyoming USA 2. Wnat is the legal location? 3. What is the duration of the project? 5days 4. What major equipment will be used if any (work over rig, drilling rig, Forkfift. winch truck. water truck etc.)? The table below is to be completed by the Project Lead and reviewed by the Environmental Special ist and the DOE NEPA Compliance Officer. NO'TE: H Change of Scope occurs, Proj ect Lead m u st $ubmlt a new NEPA Compllance Suntey and

496

NEPA COMPLIANCE SURVEY  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

:;J/7 :;J/7 Project Information Project Title: B-1-3 Heat Trace Date: 10/14/09 DOE Code: Contractor Code: Project Lead: Mike Preston Project Overview Routine maintenance activities for the buildings at B-1-3 using existing electrical rights-of-way, to repair and replace electrical lines from the electrical box to the existing buildings. This is a routine 1. What are the environmental Maintenance activities, to preserve the electrical function in the buildings at B-1-3. impacts? 2. What is the legal location? 1 Day 3. What is the duration of the project? 4. What major equipment will be used Ditch witch I Backhoe if any (work over rig, drilling rig, etc.)? The table below is to be completed by the Project Lead and reviewed by the Environmental Specialist and the DOE NEPA

497

NEPA COMPLIANCE SURVEY  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8 8 Project lnfonnation Project Title: Restoration of 62-42 SX 10 DOE Code: Project Lead: Jeff Jones Project Overview We will be restoring this location 62-42 SX-1 0. What are the environmental Date: 2/25/2010 Contractor Code: impacts? We will be removing all oil contaminated soil from location to the landfarm and recording it in the book. W e 2. What is the legal location? will then back fill with clean fill dirt from sec.20. We will remove well head and place a dry hole marker. 3. What is the duration of the project? Flush flowline and remove it. Then we will till the location and plant with native grasses. 4. What major equipment will be used if any (work over rig, drilling rig , 3-4 days etc.)? The equipment to be used will be a backhoe, tiller, dumptruck, and welder.