National Library of Energy BETA

Sample records for review checksheet attachment

  1. Attachment J-16 Portfolio Management Task Order 13-002 Title: DOE-HQ Security System Review and Assessment

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Section J Contract No. DE-AC06-09RL14728 Modification 280 Attachment J-16 Portfolio Management Task Order 13-002 Title: DOE-HQ Security System Review and Assessment Revision Number: 0 Date: 04/11/2013 Start: 05/01/2013 Finish: 07/30/2013 1.0 DESCRIPTION The DOE Office of Environmental Management (EM) Headquarters Security System (HQSS) is installed at the EM Consolidated Business Center (CBC) in Cincinnati, OH and administered from DOE Headquarters in Washington, DC. HQSS has been running as a

  2. Fenestration Attachments

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    new windows for residential and commercial buildings. Attachments Energy Rating Council (AERC), National Fenestration Rating Council (NFRC), window coverings manufacturers, ...

  3. Window Attachments

    Energy Savers [EERE]

    ... shades Surface applied film Cellular shade Window quilt Seasonal film kit Louvered blinds Roller shades Solar screens Cellular shades Surface applied films Exterior attachments ...

  4. Attachment B

    Office of Environmental Management (EM)

    B HAZARDOUS WASTE PERMIT APPLICATION PART A Waste Isolation Pilot Plant Hazardous Waste Permit April 2014 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit April 2014 PERMIT ATTACHMENT B Page B-i of 52 ATTACHMENT B HAZARDOUS WASTE PERMIT APPLICATION PART A TABLE OF CONTENTS PART A - HAZARDOUS WASTE PERMIT APPLICATION ......................................................... 1 RCRA PART A APPLICATION CERTIFICATION

  5. Attachment E

    Office of Environmental Management (EM)

    E INSPECTION SCHEDULE, PROCESS AND FORMS Waste Isolation Pilot Plant Hazardous Waste Permit April 2014 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit April 2014 PERMIT ATTACHMENT E Page E-i ATTACHMENT E INSPECTION SCHEDULE, PROCESS AND FORMS TABLE OF CONTENTS Introduction ................................................................................................................................. 1 E-1 Inspection Schedule

  6. Attachment L

    Office of Environmental Management (EM)

    L WIPP GROUNDWATER DETECTION MONITORING PROGRAM PLAN Waste Isolation Pilot Plant Hazardous Waste Permit February 2014 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit February 2014 PERMIT ATTACHMENT L Page L-i ATTACHMENT L WIPP GROUNDWATER DETECTION MONITORING PROGRAM PLAN TABLE OF CONTENTS L-1 Introduction ..................................................................................................................... 1 L-1a Geologic and Hydrologic

  7. Attachment N

    Office of Environmental Management (EM)

    N VOLATILE ORGANIC COMPOUND MONITORING PLAN Waste Isolation Pilot Plant Hazardous Waste Permit October 2013 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit October 2013 PERMIT ATTACHMENT N Page N-i ATTACHMENT N VOLATILE ORGANIC COMPOUND MONITORING PLAN TABLE OF CONTENTS N-1 Introduction ..................................................................................................................... 1 N-1a Background

  8. Attachment O

    Office of Environmental Management (EM)

    O WIPP MINE VENTILATION RATE MONITORING PLAN Waste Isolation Pilot Plant Hazardous Waste Permit May 8, 2012 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit May 8, 2012 PERMIT ATTACHMENT O Page O-1 of 14 1 ATTACHMENT O 2 WIPP MINE VENTILATION RATE MONITORING PLAN 3 TABLE OF CONTENTS 4 O-1 Definitions ....................................................................................................................... 2 5 O-2 Objective

  9. Attachment C5

    Office of Environmental Management (EM)

    C5 QUALITY ASSURANCE PROJECT PLAN REQUIREMENTS Waste Isolation Pilot Plant Hazardous Waste Permit March 13, 2013 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit March 13, 2013 PERMIT ATTACHMENT C5 Page C5-i ATTACHMENT C5 QUALITY ASSURANCE PROJECT PLAN REQUIREMENTS TABLE OF CONTENTS C5-1 Quality Assurance Project Plans ...................................................................................... 1 C5-2 Document Review, Approval, and Control

  10. ATTACHMENT J

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Contract No. DE-AC02-07CH11358 Contract Modification No. 0145 Section J, Appendix A J-A-1 ATTACHMENT J.1 APPENDIX A ADVANCE UNDERSTANDINGS ON HUMAN RESOURCES Applicable to the...

  11. Attachment K

    Office of Environmental Management (EM)

    SOLID WASTE MANAGEMENT UNIT (SWMU) AND AREA OF CONCERN (AOC) TABLES Waste Isolation Pilot Plant Hazardous Waste Permit October 2013 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit October 2013 PERMIT ATTACHMENT K Page K-i ATTACHMENT K SOLID WASTE MANAGEMENT UNIT (SWMU) AND AREA OF CONCERN (AOC) TABLES LIST OF TABLES Table Title Table K-1 Solid Waste Management Units (SWMUs) & Areas of Concern (AOCs) Requiring Corrective Action Table K-2 SWMUs & AOCs

  12. Attachment 4

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reference Chart | Department of Energy 3: Instructions for Use of Green Lease Solicitation Paragraph Reference Chart Attachment 3: Instructions for Use of Green Lease Solicitation Paragraph Reference Chart (1.84 MB) More Documents & Publications Green Lease Policies and Procedures for Lease Acquisition Attachment 1: Green Lease Policies and Procedures for Lease Acquisition Microsoft Word - AL2008-05.doc

    1 of 6 High-Level Bases and Assumptions for the WTP Project Baseline 1. The

  13. RFP Section L Attachment Templates

    Broader source: Energy.gov [DOE]

    On March 29,2010, six draft RFP Section L Attachment templates (Past Performance Information Questionnaire, Past Performance Questionnaire Cover Letter, Letter of Commitment, Past Performance Reference Information Form, ESH&Q Past Performance Information Form, and Resume Format) were distributed for Procurement Director (PD) and Head of Contracting Activity (HCA) review and comment. All comments received were considered and changes were made as appropriate. The final versions of the six aforementioned RFP Section L Attachment templates will be e-mailed directly to the Procurement Directors and made available in the STRIPES Library. For RFP's generated in STRIPES, the Section L Attachments should be identified in clause DOE-L-1033 and the file with each Attachment should be attached to the RFP.

  14. ATTACHMENT D

    Office of Environmental Management (EM)

    Applied Studies and Technology » AS&T Reports AS&T Reports 2016 Reports Uranium-Bearing Evaporite Mineralization Influencing Plume Persistence: Literature Review and DOE-LM Site Surveys Evaluation of Pre- and Post-Redevelopment Groundwater Chemical Analyses from LM Monitoring Wells 2014 Report Long-Term Surveillance Operations and Maintenance Fiscal Year 2014 Year-End Summary Report 2013 Reports Long-Term Surveillance Operations and Maintenance Fiscal Year 2013 Year-End Summary Report

  15. Attachment C1

    Office of Environmental Management (EM)

    - Summary GHG Emissions Data FINAL Attachment C - Summary GHG Emissions Data FINAL Attachment C - Summary GHG Emissions Data FINAL (33.78 KB) More Documents & Publications Attachment C

    Summary GHG Emissions Data FINAL Attachment C Summary GHG Emissions Data FINAL Attachment-C-Summary-GHG-Emissions-Data-FINAL.xlsx (34.24 KB) More Documents & Publications Attachment C -

    C1 WASTE CHARACTERIZATION TESTING METHODS Waste Isolation Pilot Plant Hazardous Waste Permit March 13, 2013

  16. Attachment N1

    Office of Environmental Management (EM)

    N1 HYDROGEN AND METHANE MONITORING PLAN Waste Isolation Pilot Plant Hazardous Waste Permit ... ATTACHMENT N1 Page N1-i ATTACHMENT N1 HYDROGEN AND METHANE MONITORING PLAN TABLE OF ...

  17. Belt attachment and system

    DOE Patents [OSTI]

    Schneider, Abraham D.; Davidson, Erick M.

    2016-02-02

    Disclosed herein is a belt assembly including a flexible belt with an improved belt attachment. The belt attachment includes two crossbars spaced along the length of the belt. The crossbars retain bearings that allow predetermined movement in six degrees of freedom. The crossbars are connected by a rigid body that attaches to the bearings. Implements that are attached to the rigid body are simply supported but restrained in pitching rotation.

  18. Blade attachment assembly

    DOE Patents [OSTI]

    Garcia-Crespo, Andres Jose; Delvaux, John McConnell; Miller, Diane Patricia

    2016-05-03

    An assembly and method for affixing a turbomachine rotor blade to a rotor wheel are disclosed. In an embodiment, an adaptor member is provided disposed between the blade and the rotor wheel, the adaptor member including an adaptor attachment slot that is complementary to the blade attachment member, and an adaptor attachment member that is complementary to the rotor wheel attachment slot. A coverplate is provided, having a coverplate attachment member that is complementary to the rotor wheel attachment slot, and a hook for engaging the adaptor member. When assembled, the coverplate member matingly engages with the adaptor member, and retains the blade in the adaptor member, and the assembly in the rotor wheel.

  19. High Performance Window Attachments

    Broader source: Energy.gov (indexed) [DOE]

    Statement: * A wide range of residential window attachments are available, but they ... to model wide range of window coverings * Performed window coverings ...

  20. Attachment C4

    Office of Environmental Management (EM)

    C4 TRU MIXED WASTE CHARACTERIZATION USING ACCEPTABLE KNOWLEDGE Waste Isolation Pilot Plant Hazardous Waste Permit March 13, 2013 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit March 13, 2013 PERMIT ATTACHMENT C4 Page C4-i ATTACHMENT C4 TRU MIXED WASTE CHARACTERIZATION USING ACCEPTABLE KNOWLEDGE TABLE OF CONTENTS C4-1 Introduction ..................................................................................................................... 1 C4-2

  1. Attachment C6

    Office of Environmental Management (EM)

    C6 AUDIT AND SURVEILLANCE PROGRAM Waste Isolation Pilot Plant Hazardous Waste Permit February 2014 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit February 2014 PERMIT ATTACHMENT C6 Page C6-i ATTACHMENT C6 AUDIT AND SURVEILLANCE PROGRAM TABLE OF CONTENTS C6-1 Introduction ..................................................................................................................... 1 C6-2 Audit Procedures

  2. Attachment G3

    Office of Environmental Management (EM)

    G3 RADIOLOGICAL SURVEYS TO INDICATE POTENTIAL HAZARDOUS WASTE RELEASES Waste Isolation Pilot Plant Hazardous Waste Permit October 2013 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit October 2013 PERMIT ATTACHMENT G3 Page G3-i ATTACHMENT G3 RADIOLOGICAL SURVEYS TO INDICATE POTENTIAL HAZARDOUS WASTE RELEASES TABLE OF CONTENTS G3-1 Purpose ........................................................................................................................... 1

  3. Attachment H1

    Office of Environmental Management (EM)

    H1 ACTIVE INSTITUTIONAL CONTROLS DURING POST-CLOSURE Waste Isolation Pilot Plant Hazardous Waste Permit November 1, 2012 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit November 1, 2012 PERMIT ATTACHMENT H1 Page H1-i ATTACHMENT H1 ACTIVE INSTITUTIONAL CONTROLS DURING POST-CLOSURE TABLE OF CONTENTS Introduction ................................................................................................................................. 1 H1.1 Active

  4. Attached is Policy Flash 2013-43 DOE F 4220.2 Small Business...

    Office of Environmental Management (EM)

    43 DOE F 4220.2 Small Business Review Form Attached is Policy Flash 2013-43 DOE F 4220.2 Small Business Review Form Attached is Policy Flash 2013-43 DOE F 4220.2 Small Business...

  5. Attachment C3

    Office of Environmental Management (EM)

    C3 QUALITY ASSURANCE OBJECTIVES AND DATA VALIDATION TECHNIQUES FOR WASTE CHARACTERIZATION METHODS Waste Isolation Pilot Plant Hazardous Waste Permit February 2014 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit February 2014 PERMIT ATTACHMENT C3 Page C3-i ATTACHMENT C3 QUALITY ASSURANCE OBJECTIVES AND DATA VALIDATION TECHNIQUES FOR WASTE CHARACTERIZATION METHODS TABLE OF CONTENTS C3-1 Validation Methods

  6. Attachment F2

    Office of Environmental Management (EM)

    F2 TRAINING COURSE AND QUALIFICATION CARD OUTLINES Waste Isolation Pilot Plant Hazardous Waste Permit October 2013 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit October 2013 PERMIT ATTACHMENT F2 Page F2-i ATTACHMENT F2 TRAINING COURSE AND QUALIFICATION CARD OUTLINES TABLE OF CONTENTS Course Outlines .......................................................................................................................... 1 GET-19X/GET-20X/GET-21X - General

  7. Attachment G2

    Office of Environmental Management (EM)

    G2 WASTE ISOLATION PILOT PLANT SHAFT SEALING SYSTEM COMPLIANCE SUBMITTAL DESIGN REPORT Waste Isolation Pilot Plant Hazardous Waste Permit October 2013 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit October 2013 PERMIT ATTACHMENT G2 Page G2-i ATTACHMENT G2 WASTE ISOLATION PILOT PLANT SHAFT SEALING SYSTEM COMPLIANCE SUBMITTAL DESIGN REPORT ADAPTED FROM: SAND96-1326/1 DISTRIBUTION UNLIMITED RELEASE CATEGORY UC-721 PRINTED AUGUST 1996 WASTE ISOLATION PILOT PLANT

  8. Attachment N1

    Office of Environmental Management (EM)

    N1 HYDROGEN AND METHANE MONITORING PLAN Waste Isolation Pilot Plant Hazardous Waste Permit January 31, 2012 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit January 31, 2012 PERMIT ATTACHMENT N1 Page N1-i ATTACHMENT N1 HYDROGEN AND METHANE MONITORING PLAN TABLE OF CONTENTS N1-1 Introduction ..................................................................................................................... 1 N1-2 Parameters to be Analyzed and Monitoring Design

  9. Attachment 3 of 5

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Department of Energy 1: Green Lease Policies and Procedures for Lease Acquisition Attachment 1: Green Lease Policies and Procedures for Lease Acquisition Green Lease Policies and Procedures for Lease Acquisition (45.31 KB) More Documents & Publications Green Lease Policies and Procedures for Lease Acquisition Attachment 2: Solicitation for Offers with New and Revised Green Lease Text Energy Efficiency in Separate Tenant Spaces - A Feasibility Study | Department of Energy

    2:

  10. Micromechanical die attachment surcharge

    DOE Patents [OSTI]

    Filter, William F.; Hohimer, John P.

    2002-01-01

    An attachment structure is disclosed for attaching a die to a supporting substrate without the use of adhesives or solder. The attachment structure, which can be formed by micromachining, functions purely mechanically in utilizing a plurality of shaped pillars (e.g. round, square or polygonal and solid, hollow or slotted) that are formed on one of the die or supporting substrate and which can be urged into contact with various types of mating structures including other pillars, a deformable layer or a plurality of receptacles that are formed on the other of the die or supporting substrate, thereby forming a friction bond that holds the die to the supporting substrate. The attachment structure can further include an alignment structure for precise positioning of the die and supporting substrate to facilitate mounting the die to the supporting substrate. The attachment structure has applications for mounting semiconductor die containing a microelectromechanical (MEM) device, a microsensor or an integrated circuit (IC), and can be used to form a multichip module. The attachment structure is particularly useful for mounting die containing released MEM devices since these devices are fragile and can otherwise be damaged or degraded by adhesive or solder mounting.

  11. Energy Savings from Window Attachments

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... of window combinations with window attachments in typical residential buildings and in varied ... The most common and widely used types of attachments are window coverings ...

  12. Ceramic blade attachment system

    DOE Patents [OSTI]

    Boyd, Gary L. (Alpine, CA)

    1994-01-01

    A turbine blade having a preestablished rate of thermal expansion is attached to a turbine wheel having a preestablished rate of thermal expansion being greater than the preestablished rate of thermal expansion of the turbine blade. The turbine blade has a root portion having a pair of recessed portions thereon. The turbine wheel includes a plurality of openings in which the turbine blade is positioned. Each of the openings have a pair of grooves therein in which are positioned a pair of pins having a generally rectangular cross-section and a reaction surface thereon. A pair of cylindrical rollers interposed respective ones of the pair of reaction surfaces and the pair of recessed portions. The attachment system or turbine assembly provides an economical, reliable and effective attachment of a component having a preestablished rate of thermal expansion to a component having a greater preestablished rate of thermal expansion.

  13. Ceramic blade attachment system

    DOE Patents [OSTI]

    Boyd, G.L.

    1994-12-13

    A turbine blade having a preestablished rate of thermal expansion is attached to a turbine wheel having a preestablished rate of thermal expansion being greater than the preestablished rate of thermal expansion of the turbine blade. The turbine blade has a root portion having a pair of recessed portions thereon. The turbine wheel includes a plurality of openings in which the turbine blade is positioned. Each of the openings have a pair of grooves therein in which are positioned a pair of pins having a generally rectangular cross-section and a reaction surface thereon. A pair of cylindrical rollers interposed respective ones of the pair of reaction surfaces and the pair of recessed portions. The attachment system or turbine assembly provides an economical, reliable and effective attachment of a component having a preestablished rate of thermal expansion to a component having a greater preestablished rate of thermal expansion. 3 figures.

  14. Magnetically attached sputter targets

    DOE Patents [OSTI]

    Makowiecki, D.M.; McKernan, M.A.

    1994-02-15

    An improved method and assembly for attaching sputtering targets to cathode assemblies of sputtering systems which includes a magnetically permeable material is described. The magnetically permeable material is imbedded in a target base that is brazed, welded, or soldered to the sputter target, or is mechanically retained in the target material. Target attachment to the cathode is achieved by virtue of the permanent magnets and/or the pole pieces in the cathode assembly that create magnetic flux lines adjacent to the backing plate, which strongly attract the magnetically permeable material in the target assembly. 11 figures.

  15. Ladder attachment platform

    DOE Patents [OSTI]

    Swygert,; Richard, W [Springfield, SC

    2012-08-28

    A ladder attachment platform is provided that includes a base for attachment to a ladder that has first and second side rails and a plurality of rungs that extend between in a lateral direction. Also included is a user platform for having a user stand thereon that is carried by the base. The user platform may be positioned with respect to the ladder so that it is not located between a first plane that extends through the first side rail and is perpendicular to the lateral direction and a second plane that extends through the second side rail and is perpendicular to the lateral direction.

  16. Internal pipe attachment mechanism

    DOE Patents [OSTI]

    Bast, R.M.; Chesnut, D.A.; Henning, C.D.; Lennon, J.P.; Pastrnak, J.W.; Smith, J.A.

    1994-12-13

    An attachment mechanism is described for repairing or extending fluid carrying pipes, casings, conduits, etc. utilizing one-way motion of spring tempered fingers to provide a mechanical connection between the attachment mechanism and the pipe. The spring tempered fingers flex to permit insertion into a pipe to a desired insertion depth. The mechanical connection is accomplished by reversing the insertion motion and the mechanical leverage in the fingers forces them outwardly against the inner wall of the pipe. A seal is generated by crushing a sealing assembly by the action of setting the mechanical connection. 6 figures.

  17. Internal pipe attachment mechanism

    DOE Patents [OSTI]

    Bast, Richard M.; Chesnut, Dwayne A.; Henning, Carl D.; Lennon, Joseph P.; Pastrnak, John W.; Smith, Joseph A.

    1994-01-01

    An attachment mechanism for repairing or extending fluid carrying pipes, casings, conduits, etc. utilizing one-way motion of spring tempered fingers to provide a mechanical connection between the attachment mechanism and the pipe. The spring tempered fingers flex to permit insertion into a pipe to a desired insertion depth. The mechanical connection is accomplished by reversing the insertion motion and the mechanical leverage in the fingers forces them outwardly against the inner wall of the pipe. A seal is generated by crushing a sealing assembly by the action of setting the mechanical connection.

  18. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachment I

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    I DE-AC36-08GO28308 Modification M1033 Attachment I Subcontracts, Purchase Orders And Other Actions Requiring DOE Review And Approval And Other Agreements Between The Parties This Attachment, implementing the Article entitled Contractor Purchasing System, sets forth the requirements for DOE's approval under the prime contract for the operation of the National Renewable Energy Laboratory. Subcontracts not binding on DOE Subcontracts and purchase orders shall be made in the name of Alliance, shall

  19. Turbine nozzle attachment system

    DOE Patents [OSTI]

    Norton, P.F.; Shaffer, J.E.

    1995-10-24

    A nozzle guide vane assembly having a preestablished rate of thermal expansion is positioned in a gas turbine engine and is attached to conventional metallic components. The nozzle guide vane assembly includes a pair of legs extending radially outwardly from an outer shroud and a pair of mounting legs extending radially inwardly from an inner shroud. Each of the pair of legs and mounting legs have a pair of holes therein. A plurality of members attached to the gas turbine engine have a plurality of bores therein which axially align with corresponding ones of the pair of holes in the legs. A plurality of pins are positioned within the corresponding holes and bores radially positioning the nozzle guide vane assembly about a central axis of the gas turbine engine. 3 figs.

  20. Turbine nozzle attachment system

    DOE Patents [OSTI]

    Norton, Paul F.; Shaffer, James E.

    1995-01-01

    A nozzle guide vane assembly having a preestablished rate of thermal expansion is positioned in a gas turbine engine and being attached to conventional metallic components. The nozzle guide vane assembly includes a pair of legs extending radially outwardly from an outer shroud and a pair of mounting legs extending radially inwardly from an inner shroud. Each of the pair of legs and mounting legs have a pair of holes therein. A plurality of members attached to the gas turbine engine have a plurality of bores therein which axially align with corresponding ones of the pair of holes in the legs. A plurality of pins are positioned within the corresponding holes and bores radially positioning the nozzle guide vane assembly about a central axis of the gas turbine engine.

  1. Ceramic blade attachment system

    DOE Patents [OSTI]

    Frey, deceased, Gary A. (late of Poway, CA); Jimenez, Oscar D. (Escondia, CA)

    1996-01-01

    A turbine blade having a preestablished rate of thermal expansion is attached to a turbine flange having a preestablished rate of thermal expansion being greater than the preestablished rate of thermal expansion of the turbine blade. The turbine flange includes a first upstanding flange and a second upstanding flange having a groove formed therebetween. The turbine flange further includes a recess. Each of the first and second upstanding flanges have a plurality of bores therein. A turbine blade has a first member and a second member positioned in one of the groove and the recess. Each of the first member and the second member have a plurality of bores therein. And, a pin is positioned in respective ones of the plurality of bores in the first and second upstanding members and the first and second members and attach the blade to the turbine flange. The pin has a preestablished rate of thermal expansion being substantially equal to the rate of thermal expansion of the blade.

  2. Ceramic blade attachment system

    DOE Patents [OSTI]

    Frey, G.A.; Jimenez, O.D.

    1996-12-03

    A turbine blade having a preestablished rate of thermal expansion is attached to a turbine flange having a preestablished rate of thermal expansion being greater than the preestablished rate of thermal expansion of the turbine blade. The turbine flange includes a first upstanding flange and a second upstanding flange having a groove formed between them. The turbine flange further includes a recess. Each of the first and second upstanding flanges have a plurality of bores therein. A turbine blade has a first member and a second member positioned in one of the groove and the recess. Each of the first member and the second member have a plurality of bores therein. A pin is positioned in respective ones of the plurality of bores in the first and second upstanding members and the first and second members and attach the blade to the turbine flange. The pin has a preestablished rate of thermal expansion being substantially equal to the rate of thermal expansion of the blade. 4 figs.

  3. Composite Underbody Attachment

    Broader source: Energy.gov [DOE]

    2010 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and Peer Evaluation Meeting, June 7-11, 2010 -- Washington D.C.

  4. Appendix TFIELD Attachment A: Attachment A: TFIELD-2014 Visualization

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Attachment A: TFIELD-2014 Visualization United States Department of Energy Waste Isolation Pilot Plant Carlsbad Field Office Carlsbad, New Mexico Compliance Recertification Application 2014 Attachment A: TFIELD-2014 Visualization This attachment contains figures for Appendix TFIELD-2014, related to the Culebra T-Field calibration process, performed as part of the 2009 Compliance Recertification Application (CRA-2009) Performance Assessment Baseline Calculation (PABC). These parameter inputs and

  5. Ceramic blade attachment system

    DOE Patents [OSTI]

    Shaffer, James E. (Maitland, FL)

    1995-01-01

    A turbine blade having a preestablished rate of thermal expansion is attached to a turbine wheel having a preestablished rate of thermal expansion being greater than the preestablished rate of thermal expansion of the turbine blade. The turbine blade has a root portion having a first groove and a second groove therein. The turbine wheel includes a plurality of openings in which the turbine blade is positioned. Each of the openings has a first groove and a second groove therein. The space or void formed between the first grooves and the second grooves has a plurality of spherical balls positioned therein. The plurality of spherical balls has a preestablished rate of thermal expansion being equal to the preestablished rate of thermal expansion of the turbine blade.

  6. Ceramic blade attachment system

    DOE Patents [OSTI]

    Shaffer, James E. (Maitland, FL)

    1995-01-01

    A turbine blade having a preestablished rate of thermal expansion is attached to a turbine disc having a preestablished rate of thermal expansion being greater than the preestablished rate of thermal expansion of the turbine blade and forms a turbine assembly. The turbine blade has a root portion defining a pair of sides having a pair of grooves therein. The turbine assembly includes a pair of flanges between which the turbine blades are positioned. Each of the pair of flanges has a plurality of grooves defined therein. The grooves within the pair of flanges are aligned with the grooves in the blades and have a space formed therebetween. A plurality of spherical balls are positioned within the space. The plurality of spherical balls has a preestablished rate of thermal expansion being equal to the preestablished rate of thermal expansion of the turbine blade.

  7. Ceramic blade attachment system

    DOE Patents [OSTI]

    Shaffer, J.E.

    1995-01-10

    A turbine blade having a preestablished rate of thermal expansion is attached to a turbine wheel having a preestablished rate of thermal expansion being greater than the preestablished rate of thermal expansion of the turbine blade. The turbine blade has a root portion having a first groove and a second groove therein. The turbine wheel includes a plurality of openings in which the turbine blade is positioned. Each of the openings has a first groove and a second groove therein. The space or void formed between the first grooves and the second grooves has a plurality of spherical balls positioned therein. The plurality of spherical balls has a preestablished rate of thermal expansion being equal to the preestablished rate of thermal expansion of the turbine blade. 4 figures.

  8. Ceramic blade attachment system

    DOE Patents [OSTI]

    Shaffer, J.E.

    1995-07-11

    A turbine blade having a preestablished rate of thermal expansion is attached to a turbine disc having a preestablished rate of thermal expansion being greater than the preestablished rate of thermal expansion of the turbine blade and forms a turbine assembly. The turbine blade has a root portion defining a pair of sides having a pair of grooves therein. The turbine assembly includes a pair of flanges between which the turbine blades are positioned. Each of the pair of flanges has a plurality of grooves defined therein. The grooves within the pair of flanges are aligned with the grooves in the blades and have a space formed therebetween. A plurality of spherical balls are positioned within the space. The plurality of spherical balls has a preestablished rate of thermal expansion being equal to the preestablished rate of thermal expansion of the turbine blade. 4 figs.

  9. Attachment C5

    Office of Environmental Management (EM)

    pages need to 39 be reissued. Changes to documents, other than those defined as editorial changes or minor 40 changes, shall be reviewed and approved by the same functional...

  10. Attachment 6 - Government Property List

    National Nuclear Security Administration (NNSA)

    2 EQUIPMENT - HANDHELD COMPUTER - WIRELESS WHEEL LOAD SYSTEM 1 EQUIPMENT - HEAT STRESS MONITOR 5 EQUIPMENT - HOIST - PORTABLE 1 November 20, 2013 DE-SOL-0005982 Attachment 6...

  11. Attachment A -- Deliverables.xls

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4: Unrevised SFO Paragraphs Reissued Attachment 4: Unrevised SFO Paragraphs Reissued Unrevised SFO Paragraphs Reissued (35.68 KB) More Documents & Publications Attachment 2: Solicitation for Offers with New and Revised Green Lease Text Attachment 1: Green Lease Policies and Procedures for Lease Acquisition 1

    B - J Deliverables Attachment A TOC Deliverables DE-AC27-08RV14800 SEC. Contract Section Description Action Timing TFP CO ESQ OPA IR/HR ORP MGR DCAA B B.2 Modify contract to obligate

  12. Revised Merit Review Guide for Financial Assistance

    Office of Energy Efficiency and Renewable Energy (EERE)

    Attached is the revised Merit Review Guide for Financial Assistance. Revisions include reformatting and updating of the information presented in the Guide and Attachments.

  13. Attachment C: Optional AIP Provisions

    Broader source: Energy.gov [DOE]

    This attachment contains sample language for a number of optional provisions that sites may choose to include or not to include in their AIPs. Optional AIP provisions are not mandatory and the...

  14. Attachment 1 - Performance Work Statement

    National Nuclear Security Administration (NNSA)

    including TTR. Waste acceptance services will be performed at the NNSS and at waste generator sites. DE-SOL-0005982 Attachment 1 Page 1 2. Scope of Work 2.1 Requirement: The EPS...

  15. ATTACHMENT

    Broader source: Energy.gov (indexed) [DOE]

    Pages. Under Estimated Total Size, you will see the original file size and the 3. Click OK to accept the file size compression. compressed file size. U.S. Department of Energy,...

  16. ATTACHMENT

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... to be Public 7 PII and includes, for example, first and last name, address, work telephone number, e-mail address, home telephone number, and general educational credentials. ...

  17. ATTACHMENT F PAST PERFORMANCE QUESTIONNAIRE

    National Nuclear Security Administration (NNSA)

    SOURCE SELECTION INFORMATION - SEE FAR 3.104 (When Filled-In) 1 ATTACHMENT F PAST PERFORMANCE QUESTIONNAIRE Offerors are responsible for sending copies of the PAST PERFORMANCE QUESTIONNAIRE (SECTIONs A thru C) to references. Instructions to Offeror 1. For each reference submitted in your proposal, enter the required information in Section A. 2. Transmit the entire questionnaire to the identified Points of Contract (POCs) and place one copy of each Section A in your proposal submittal. NOTES:

  18. Attachment L-1 - Entity Certificates

    National Nuclear Security Administration (NNSA)

    3] Attachment L-1 1 ENTITY CERTIFICATE The offeror shall submit evidence to substantiate the authority of the person signing the offer and submit in Volume I of the proposal. CERTIFICATE I, _______________________________________________, certify that I have the signatory authority as the _________________________________________ to sign this offer/contract on behalf of said entity and to bind the entity by the authority of its governing body and within the scope of its powers. Affix the

  19. Microsoft Word - Attachment I.doc

    Office of Environmental Management (EM)

    SCHEDULE RESERVED Waste Isolation Pilot Plant Hazardous Waste Permit November 30, 2010 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit November 30, 2010 PERMIT ATTACHMENT I Page I-i ATTACHMENT I COMPLIANCE SCHEDULE RESERVED

  20. Microsoft Word - Attachment M.doc

    Office of Environmental Management (EM)

    M FIGURES RESERVED Waste Isolation Pilot Plant Hazardous Waste Permit November 30, 2010 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit November 30, 2010 PERMIT ATTACHMENT M Page M-i ATTACHMENT M FIGURES RESERVED

  1. Attachment D: Mandatory Provisions if Applicable

    Broader source: Energy.gov [DOE]

    This attachment contains provisions that may be mandatory for an AIP if the State: (1) chooses to develop an emergency response program but does not want to use the suggested language in Attachment...

  2. Microsoft Word - Attachment J.doc

    Office of Environmental Management (EM)

    Waste Isolation Pilot Plant Hazardous Waste Permit April 15, 2011 PERMIT ATTACHMENT J Page J-i ATTACHMENT J HAZARDOUS WASTE MANAGEMENT UNIT TABLES LIST OF TABLES Table Title...

  3. Attachment C … Waste Analysis Plan

    Office of Environmental Management (EM)

    Configurations | Department of Energy Attachment A: Modeling in Support of Additional Two-Unit Operating Configurations Attachment A: Modeling in Support of Additional Two-Unit Operating Configurations Docket No. EO-05-01: Attachment to the Operating Plan of Mirant Potomac River, LLC Attachment A: Modeling in Support of Additional Two-Unit Operating Configurations (28.18 KB) More Documents & Publications Mirant Potomac, Alexandria, Virginia: Maximum Impacts Predicted by AERMOD-PRIME

  4. Attachments Energy Ratings Council | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Attachments Energy Ratings Council Attachments Energy Ratings Council Attachments Energy Ratings Council Lead Performer: Window Covering Manufacturing Association - New York, NY DOE Funding: $1,600,000 Project Term: October 1, 2014 - September 30, 2018 Funding Opportunity Announcement: Certification and Rating Attachments for Fenestration Technologies DE-FOA-001000-1504 Project Objective This project is to develop an independent rating, certification, labeling, and performance verification

  5. Shading, Films and Window Attachments Market Report

    Broader source: Energy.gov [DOE]

    Shading, Films and Window Attachments (SFWA) Market Report, March 13, 2016, from the Consortium for Building Energy Innovation.

  6. Split ring containment attachment device

    DOE Patents [OSTI]

    Sammel, Alfred G.

    1996-01-01

    A containment attachment device 10 for operatively connecting a glovebag 200 to plastic sheeting 100 covering hazardous material. The device 10 includes an inner split ring member 20 connected on one end 22 to a middle ring member 30 wherein the free end 21 of the split ring member 20 is inserted through a slit 101 in the plastic sheeting 100 to captively engage a generally circular portion of the plastic sheeting 100. A collar potion 41 having an outer ring portion 42 is provided with fastening means 51 for securing the device 10 together wherein the glovebag 200 is operatively connected to the collar portion 41.

  7. DNA attachment to support structures

    DOE Patents [OSTI]

    Balhorn, Rodney L.; Barry, Christopher H.

    2002-01-01

    Microscopic beads or other structures are attached to nucleic acids (DNA) using a terminal transferase. The transferase adds labeled dideoxy nucleotide bases to the ends of linear strands of DNA. The labels, such as the antigens digoxigenin and biotin, bind to the antibody compounds or other appropriate complementary ligands, which are bound to the microscopic beads or other support structures. The method does not require the synthesis of a synthetic oligonucleotide probe. The method can be used to tag or label DNA even when the DNA has an unknown sequence, has blunt ends, or is a very large fragment (e.g., >500 kilobase pairs).

  8. ATTACHMENT J.7 - APPENDIX G

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Modification No. 0199 Contract No. DE-AC02-09CH11466 Section J - Appendix G J-G-1 ATTACHMENT J.7 APPENDIX G PURCHASING SYSTEM REQUIREMENTS Applicable to the Operation of PPPL Contract No. DE-AC02-09CH11466 Modification No. 0199 Contract No. DE-AC02-09CH11466 Section J - Appendix G J-G-2 Appendix G Purchasing System Requirements This Appendix and Clause I.146 "Contractor Purchasing System," sets forth DOE requirements applicable to the Purchasing System established under the Contract

  9. Attachment A -- Deliverables.xls

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    I Deliverables Attachment A TOC Deliverables DE-AC27-08RV14800 SEC. FAR/DEAR Clause Reference Description Action Timing TFP CO ESQ OPA IR/HR ORP MGR DCAA I.2 FAR 52.202-1 Definitions (JUL 2004) as supplemented by DEAR 952.202-1 (Mar 2002) Verify compliance As Required L I.3 FAR 52.203-3 Gratuities (APR 1984) Verify compliance As Required L I.4 FAR 52.203-5 Covenant Against Contingent Fees (APR 1984) Verify compliance As Required L I.5 FAR 52.203-6 Restrictions on Subcontractor Sales to the

  10. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachment O

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    O DE-AC36-08GO28308 Modification M1033 Attachment O

  11. Methane production by attached film

    DOE Patents [OSTI]

    Jewell, William J.

    1981-01-01

    A method for purifying wastewater of biodegradable organics by converting the organics to methane and carbon dioxide gases is disclosed, characterized by the use of an anaerobic attached film expanded bed reactor for the reaction process. Dilute organic waste material is initially seeded with a heterogeneous anaerobic bacteria population including a methane-producing bacteria. The seeded organic waste material is introduced into the bottom of the expanded bed reactor which includes a particulate support media coated with a polysaccharide film. A low-velocity upward flow of the organic waste material is established through the bed during which the attached bacterial film reacts with the organic material to produce methane and carbon dioxide gases, purified water, and a small amount of residual effluent material. The residual effluent material is filtered by the film as it flows upwardly through the reactor bed. In a preferred embodiment, partially treated effluent material is recycled from the top of the bed to the bottom of the bed for further treatment. The methane and carbon dioxide gases are then separated from the residual effluent material and purified water.

  12. Microsoft Word - Policy Flash 2010-77 Attachment | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    7 Attachment Microsoft Word - Policy Flash 2010-77 Attachment Microsoft Word - Policy Flash 2010-77 Attachment More Documents & Publications Microsoft Word - Policy Flash 2010-78...

  13. Microsoft Word - Attachment 3 Recovery Act notification | Department...

    Energy Savers [EERE]

    Microsoft Word - Attachment 3 Recovery Act notification Microsoft Word - Attachment 3 Recovery Act notification More Documents & Publications Microsoft Word - Attachment 3 Recovery...

  14. Microsoft Word - Policy Flash 2010-81 Attachment 1 | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1 Attachment 1 Microsoft Word - Policy Flash 2010-81 Attachment 1 Microsoft Word - Policy Flash 2010-81 Attachment 1 More Documents & Publications Microsoft Word - Policy Flash...

  15. Attached is Policy Flash 2013-44 Acquisition Guide- Allowability...

    Energy Savers [EERE]

    Attached is Policy Flash 2013-44 Acquisition Guide- Allowability of Incurred Costs Attached is Policy Flash 2013-44 Acquisition Guide- Allowability of Incurred Costs Attached is...

  16. Attachment FY2011-75 OPAM | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    OPAM Attachment FY2011-75 OPAM Federal Supply Schedules Attachment FY2011-75 OPAM More Documents & Publications Chapter 8 - Required Sources of Supplies and Services Attachment...

  17. ATTACHMENT J.3 - APPENDIX C

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    99 Contract No.: DE-AC02-09CH11466 Section J - Appendix C J-C-1 ATTACHMENT J.3 APPENDIX C SPECIAL FINANCIAL INSTITUTION ACCOUNT AGREEMENT Applicable to the Operation of PPPL Contract No. DE-AC02-09CH11466 Modification No. 0199 Contract No.: DE-AC02-09CH11466 Section J - Appendix C J-C-2 Modification N o: 0 199 Contract N o: D E---AC02---09CH11466 Section J --- A ppendix C Information c ontained i n t his d ocument i s r estricted. C ontact P PPL v ia e mail--- j delooper@pppl.gov t o r equest a

  18. Merit Review Guide for Financial Assistance | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Merit Review Guide for Financial Assistance Merit Review Guide for Financial Assistance Merit Review Guide FINAL JULY 2013.pdf (180.3 KB) ATTACHMENT 1 Sample Merit Rev Panel Appt Letter 1-10 (27.88 KB) ATTACHMENT 2 Sample COI ADDED WB LANGUAGE JULY 2013 (24.98 KB) ATTACHMENT 3 - Sample Evaluation and Selection Plan JULY 2013 (90.83 KB) ATTACHMENT 4 Sample Noncompetitive Review Plan (18.1 KB) ATTACHMENT 5 Sample Initial Compliance Review 1-16 (19.97 KB) ATTACHMENT 6 Sample Eval Criteria and

  19. AttachmentFlash_2010-55.pdf | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AttachmentFlash2010-55.pdf More Documents & Publications AttachmentFlash2010-66.pdf AttachmentFlash2010-73(3).pdf AttachmentFlash2010-33(2).pdf...

  20. al99-06attachment.doc | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    attachment.doc&0; al99-06attachment.doc&0; PDF icon al99-06attachment.doc&0; More Documents & Publications Microsoft Word - AL2000-05Attachment.doc Microsoft Word - NSRC...

  1. Microsoft Word - Attachment J-4 Legal Management Plan.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4-1 ATTACHMENT J.4. LEGAL MANAGEMENT

  2. Building America Expert Meeting: Cladding Attachment Over Exterior...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Building America Expert Meeting: Cladding Attachment Over Exterior Insulation Building America Expert Meeting: Cladding Attachment Over Exterior Insulation Building Science...

  3. Introducing the Attachments Energy Ratings Council

    Broader source: Energy.gov [DOE]

    In collaboration with the U.S. Department of Energy (DOE), the Window Covering Manufacturers Association (WCMA) has launched the Attachments Energy Ratings Council (AERC).

  4. Bonneville Power Administration Attachment P Oversupply Management...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    reduced generation in order to meet the Transmission Customers' schedules. The Oversupply Management Protocol will apply as follows: 1. The term of this attachment is March 31,...

  5. Cladding Attachment Over Thick Exterior Rigid Insulation

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Double Bending Linear (10 Cantilever) Linear (10 Double Bending) Cladding Attachment ... Compression Strut Function of fastener tension and insulation compression Measured ...

  6. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachment K

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    K DE-AC36-08GO28308 Modification M1033 Attachment K Diversity Plan Diversity Plan CY2014 is hereby incorporated as Attachment K of the contract

  7. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachment C

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    C DE-AC36-08GO28308 Modification M1033 Attachment C Small Business Subcontracting Plan

  8. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachment S

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    S DE-AC36-08GO28308 Modification M1033 Attachment S Human Resources Compensation Plan

  9. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachment T

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    T DE-AC36-08GO28308 Modification M1033 Attachment T Human Resources Workforce Plan

  10. Microsoft Word - Attachment F1.doc

    Office of Environmental Management (EM)

    F1 RCRA HAZARDOUS WASTE MANAGEMENT JOB TITLES AND DESCRIPTIONS Waste Isolation Pilot Plant Hazardous Waste Permit November 30, 2010 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit November 30, 2010 PERMIT ATTACHMENT F1 Page F1-i ATTACHMENT F1 RCRA HAZARDOUS WASTE MANAGEMENT JOB TITLES AND DESCRIPTIONS TABLE OF CONTENTS Job

  11. Nuclear reactor fuel rod attachment system

    DOE Patents [OSTI]

    Not Available

    1980-09-17

    A reusable system is described for removably attaching a nuclear reactor fuel rod to a support member. A locking cap is secured to the fuel rod and a locking strip is fastened to the support member. The locking cap has two opposing fingers shaped to form a socket having a body portion. The locking strip has an extension shaped to rigidly attach to the socket's body portion. The locking cap's fingers are resiliently deflectable. For attachment, the locking cap is longitudinally pushed onto the locking strip causing the extension to temporarily deflect open the fingers to engage the socket's body portion. For removal, the process is reversed.

  12. EXHIBIT G7.0 Attachment 2

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    G7.0 Attachment 2 32014 Page 1 SUBCONTRACTOR CYBER SECURITY PLAN Vendor Name (if Applicable): Subcontract No. PR- Ex. G dated: XXXXXX Rev. No.: 7 Pursuant to the requirements in...

  13. Microsoft Word - Attachment coversheet.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    HANFORD MISSION SUPPORT CONTRACT ADVANCE UNDERSTANDING ON COST REVISED DECEMBER 31, 2014 Mission Support Contract Contract Number DE-AC06-09RL14728 Attachment J, Section J.8...

  14. ATTACHMENT A - CHECKLIST FOR SELF ASSESSMENT

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ATTACHMENT A - CHECKLIST FOR SELF ASSESSMENT Site: Federal or Contractor Program: Name: ____________________________________________ Title:______________________________________________ Organization:_______________________________________ Address: __________________________________________ Bldg and Room Number _____________________________ Phone Number __________________ E-Mail ________________________________ Years of Records Management experience? Length of time in current position? Training?

  15. Appendix DATA Attachment A: WIPP Borehole Update

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Carlsbad Field Office Carlsbad, New Mexico Appendix DATA-2014 Attachment A: WIPP Borehole Update Table of Contents DATA-A-1.0 WIPP Boreholes DATA-A-2.0 Individual Well Reports ...

  16. River Corridor Closure Contract Section J, Attachment...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 Contract No. DE-AC06-05RL14655 A000 1 ATTACHMENT J-12 GOVERNMENT-FURNISHED SERVICES AND INFORMATION (GFSI) GFSI Item Scope Description GFSI Description C.4 Hanford Site...

  17. Microsoft Word - Attachment G1.doc

    Office of Environmental Management (EM)

    DETAILED DESIGN REPORT FOR AN OPERATION PHASE PANEL CLOSURE SYSTEM Adapted from DOE/WIPP 96-2150 Waste Isolation Pilot Plant Hazardous Waste Permit November 30, 2010 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit November 30, 2010 PERMIT ATTACHMENT G1 Page G1-i ATTACHMENT G1 DETAILED DESIGN REPORT FOR AN OPERATION PHASE PANEL CLOSURE SYSTEM TABLE OF CONTENTS Executive Summary

  18. Microsoft Word - Attachment J.doc

    Office of Environmental Management (EM)

    UNIT TABLES Waste Isolation Pilot Plant Hazardous Waste Permit April 15, 2011 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit April 15, 2011 PERMIT ATTACHMENT J Page J-i ATTACHMENT J HAZARDOUS WASTE MANAGEMENT UNIT TABLES LIST OF TABLES Table Title Table J-1 Waste Handling Building (WHB) Container Storage Unit Table J-2 Parking Area Container Storage Unit Table J-3 Underground Hazardous Waste Disposal Units Waste Isolation Pilot Plant Hazardous Waste Permit

  19. Attachment device for an inflatable protective cushion

    DOE Patents [OSTI]

    Nelsen, James M.; Luna, Daniel A.; Gwinn, Kenneth W.

    1997-01-01

    An inflatable cushion assembly for use with an inflator comprises an inflatable cushion having an inner surface, outer surface, and at least one protrusion extending from one of the inner or outer surfaces. The inflatable cushion defines an opening between the inner surface and the outer surface for receiving the inflator. An attachment member contacts the one of the inner or outer surfaces adjacent the opening and includes a groove for receiving the protrusion, the attachment member securing the inflator within the opening.

  20. Attachment device for an inflatable protective cushion

    DOE Patents [OSTI]

    Nelsen, James M.; Luna, Daniel A.; Gwinn, Kenneth W.

    1998-01-01

    An inflatable cushion assembly for use with an inflator comprises an inflatable cushion having an inner surface, outer surface, and at least one protrusion extending from one of the inner or outer surfaces. The inflatable cushion defines an opening between the inner surface and the outer surface for receiving the inflator. An attachment member contacts the one of the inner or outer surfaces adjacent the opening and includes a groove for receiving the protrusion, the attachment member securing the inflator within the opening.

  1. Microsoft Word - Policy Flash 2010-81 Attachment 2 | Department...

    Office of Environmental Management (EM)

    81 Attachment 2 Microsoft Word - Policy Flash 2010-81 Attachment 2 Microsoft Word - Policy Flash 2010-81 Attachment 2 More Documents & Publications ATTACHMENTFLASH2010.81(2)-OPAM...

  2. Microsoft Word - Policy Flash 2011-2 Attachment 1 | Department...

    Energy Savers [EERE]

    Microsoft Word - Policy Flash 2011-2 Attachment 1 Microsoft Word - Policy Flash 2011-2 Attachment 1 Microsoft Word - Policy Flash 2011-2 Attachment 1 More Documents & Publications...

  3. Microsoft Word - Policy Flash 2010-81 Attachment 1 | Department...

    Energy Savers [EERE]

    Microsoft Word - Policy Flash 2010-81 Attachment 1 Microsoft Word - Policy Flash 2010-81 Attachment 1 Microsoft Word - Policy Flash 2010-81 Attachment 1 More Documents &...

  4. Microsoft Word - Policy Flash 2010-67 Attachment 1 | Department...

    Office of Environmental Management (EM)

    67 Attachment 1 Microsoft Word - Policy Flash 2010-67 Attachment 1 Microsoft Word - Policy Flash 2010-67 Attachment 1 More Documents & Publications Acquisition Letter 2009-03...

  5. Attachment C - Summary GHG Emissions Data FINAL | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    - Summary GHG Emissions Data FINAL Attachment C - Summary GHG Emissions Data FINAL Attachment C - Summary GHG Emissions Data FINAL (33.78 KB) More Documents & Publications Attachment C

  6. Attachment C Summary GHG Emissions Data FINAL | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Summary GHG Emissions Data FINAL Attachment C Summary GHG Emissions Data FINAL Attachment-C-Summary-GHG-Emissions-Data-FINAL.xlsx (34.24 KB) More Documents & Publications Attachment C -

  7. Attachment FY2011-83 OPAM | Department of Energy

    Office of Environmental Management (EM)

    3 OPAM Attachment FY2011-83 OPAM Federal Supply Schedules Attachment FY2011-83 OPAM More Documents & Publications Chapter 8 - Required Sources of Supplies and Services Attachment...

  8. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachment M

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    M DE-AC36-08GO28308 Modification M1033 Attachment M Equal Opportunity Program Incorporated by Reference In Modification M004

  9. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachment N

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    N DE-AC36-08GO28308 Modification M1033 Attachment N Supplemental Requirements To Laws, Regulations, And Doe Directives

  10. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachments H

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    H DE-AC36-08GO28308 Modification M1033 Attachment H Performance Guarantee Agreement Incorporated by Reference In Modification M004

  11. Attachment 3: Instructions for Use of Green Lease Solicitation...

    Energy Savers [EERE]

    Attachment 3: Instructions for Use of Green Lease Solicitation Paragraph Reference Chart Attachment 3: Instructions for Use of Green Lease Solicitation Paragraph Reference Chart...

  12. Attachment 2: Solicitation for Offers with New and Revised Green...

    Energy Savers [EERE]

    Attachment 2: Solicitation for Offers with New and Revised Green Lease Text Attachment 2: Solicitation for Offers with New and Revised Green Lease Text PDF icon Solicitation for...

  13. Attachment 1: Green Lease Policies and Procedures for Lease Acquisitio...

    Energy Savers [EERE]

    Attachment 1: Green Lease Policies and Procedures for Lease Acquisition Attachment 1: Green Lease Policies and Procedures for Lease Acquisition PDF icon Green Lease Policies and...

  14. Collimator with attachment mechanism and system (Patent) | DOEPatents

    Office of Scientific and Technical Information (OSTI)

    Data Explorer Search Results Collimator with attachment mechanism and system Title: Collimator with attachment mechanism and system A self-aligning collimator for a radiation ...

  15. Apparatus for attaching a cleaning tool to a robotic manipulator...

    Office of Scientific and Technical Information (OSTI)

    Apparatus for attaching a cleaning tool to a robotic manipulator Title: Apparatus for attaching a cleaning tool to a robotic manipulator This invention is comprised of an apparatus ...

  16. Apparatus for attaching a cleaning tool to a robotic manipulator...

    Office of Scientific and Technical Information (OSTI)

    Apparatus for attaching a cleaning tool to a robotic manipulator Title: Apparatus for attaching a cleaning tool to a robotic manipulator You are accessing a document from the ...

  17. Property:NEPA ApplicationAttachments | Open Energy Information

    Open Energy Info (EERE)

    ApplicationAttachments Jump to: navigation, search Property Name NEPA ApplicationAttachments Property Type Page Description FONSI files for NEPA Docs. For example: Cover letters,...

  18. Merit Review System | U.S. DOE Office of Science (SC)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Merit Review Guide for Financial Assistance Merit Review Guide for Financial Assistance Merit Review Guide FINAL JULY 2013.pdf (180.3 KB) ATTACHMENT 1 Sample Merit Rev Panel Appt Letter 1-10 (27.88 KB) ATTACHMENT 2 Sample COI ADDED WB LANGUAGE JULY 2013 (24.98 KB) ATTACHMENT 3 - Sample Evaluation and Selection Plan JULY 2013 (90.83 KB) ATTACHMENT 4 Sample Noncompetitive Review Plan (18.1 KB) ATTACHMENT 5 Sample Initial Compliance Review 1-16 (19.97 KB) ATTACHMENT 6 Sample Eval Criteria and

  19. HAB_Attachement_2_review_cycle.pdf

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

  20. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachment J

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    J DE-AC36-08GO28308 Modification M1033 Attachment J Performance Evaluation And Measurement Plan FY 2015 Performance Evaluation And Measurement Plan dated May 11, 2015, Rev 4, is hereby incorporated into this contract by reference as Section J, Attachment J

  1. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachment L

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    L DE-AC36-08GO28308 Modification M1033 Attachment L Employee Concerns Program (ECP) Implementation Plan The Employee Concerns Program Plan, dated January 22, 2015, is hereby incorporated into this contract by reference as Section J, Attachment L

  2. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachment P

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    P DE-AC36-08GO28308 Modification M1033 Attachment P Five Year Strategic Plan NREL's Five-Year Plan (FY15-FY19), dated October 23, 2014, Rev 2, is hereby incorporated into this contract by reference as Section J, Attachment P

  3. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachment Q

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Q DE-AC36-08GO28308 Modification M1033 Attachment Q Organizational Conflict Of Interest Management Plan Organizational Conflicts of Interest Management Plan and Implementation Program, Volumes I and II, dated October 6, 2014, are hereby incorporated into this contract by reference as Section J, Attachment Q

  4. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachment R

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    R DE-AC36-08GO28308 Modification M1033 Attachment R Organizational Conflict Of Interest Implementation Program Organizational Conflicts of Interest Management Plan and Implementation Program, Volumes I and II, dated October 6, 2014, are hereby incorporated into this contract by reference as Section J, Attachment R

  5. Nuclear reactor fuel rod attachment system

    DOE Patents [OSTI]

    Christiansen, David W. (Kennewick, WA)

    1982-01-01

    A reusable system for removably attaching a nuclear reactor fuel rod (12) to a support member (14). A locking cap (22) is secured to the fuel rod (12) and a locking strip (24) is fastened to the support member (14). The locking cap (22) has two opposing fingers (24a and 24b) shaped to form a socket having a body portion (26). The locking strip has an extension (36) shaped to rigidly attach to the socket's body portion (26). The locking cap's fingers are resiliently deflectable. For attachment, the locking cap (22) is longitudinally pushed onto the locking strip (24) causing the extension (36) to temporarily deflect open the fingers (24a and 24b) to engage the socket's body portion (26). For removal, the process is reversed.

  6. Attachment device for an inflatable protective cushion

    DOE Patents [OSTI]

    Nelsen, J.M.; Luna, D.A.; Gwinn, K.W.

    1997-11-18

    An inflatable cushion assembly for use with an inflator comprises an inflatable cushion having an inner surface, outer surface, and at least one protrusion extending from one of the inner or outer surfaces. The inflatable cushion defines an opening between the inner surface and the outer surface for receiving the inflator. An attachment member contacts the one of the inner or outer surfaces adjacent the opening and includes a groove for receiving the protrusion, the attachment member securing the inflator within the opening. 22 figs.

  7. Attachment device for an inflatable protective cushion

    DOE Patents [OSTI]

    Nelsen, J.M.; Luna, D.A.; Gwinn, K.W.

    1998-12-08

    An inflatable cushion assembly for use with an inflator comprises an inflatable cushion having an inner surface, outer surface, and at least one protrusion extending from one of the inner or outer surfaces. The inflatable cushion defines an opening between the inner surface and the outer surface for receiving the inflator. An attachment member contacts the one of the inner or outer surfaces adjacent the opening and includes a groove for receiving the protrusion, the attachment member securing the inflator within the opening. 22 figs.

  8. Annual Report Outline (IDIQ Attachment J-10) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Report Outline (IDIQ Attachment J-10) Annual Report Outline (IDIQ Attachment J-10) Document offers an annual report outline sample for an energy savings performance contract. Download the annual report outline. (48.62 KB) More Documents & Publications Post-Installation Report Outline (IDIQ Attachment J-9) Measurement and Verification Plan and Savings Calculations Methods Outline (IDIQ Attachment J-8) ESPC Task Order Financial Schedules (IDIQ Attachment J-6

  9. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachment G

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    G DE-AC36-08GO28308 Modification M1033 Attachment G Sensitive Foreign Nations Control In accordance with the Clause I.92, Sensitive Foreign Nations Controls, this Attachment sets forth the requirements the contractor shall comply with under this contract. (Reference DOE Order 142.3, or superseding directives.) Foreign National access to DOE sites, programs, information and technologies will be approved provided the access is needed to support the program objectives of DOE and/or objectives of

  10. Methods of attaching erosion-resistant nonmetallic panels

    SciTech Connect (OSTI)

    Girzhel, A.M.

    1984-01-01

    Attachment methods for panels of wear-resistant nonmetallic materials, e.g. cast stone and slag, devitrified slag, and erosion-resistant and heat-resistant concretes to protect hopper, chute, and trough structures at metallurgical and coal industries have been investigated. Attachment methods can be divided into two groups, attachment by adhesives and by mechanical attachment. A new method of mechanical attachment, considered to be much superior to adhesive attachment, provides for reliable fastening without damage to the protected metal structure. Various panel designs may be used depending on the operating conditions.

  11. EECBG SEP Attachment 1 - Process metric list

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    10-07B/SEP 10-006A Attachment 1: Process Metrics List Metric Area Metric Primary or Optional Metric Item(s) to Report On 1. Building Retrofits 1a. Buildings retrofitted, by sector Number of buildings retrofitted Square footage of buildings retrofitted 1b. Energy management systems installed, by sector Number of energy management systems installed Square footage of buildings under management 1c. Building roofs retrofitted, by sector Number of building roofs retrofitted Square footage of building

  12. Attachment FY2011-55 OPAM

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1, Summary of Small Business Administration and Department of Energy Partnership Agreement Reference: FAR 19.8 Overview Recently, the Secretary and the Administrator of the Small Business Administration (SBA) executed a Partnership Agreement to expedite the award of requirements pursuant to section 8(a) of the Small Business Act. It will remain in effect through September 30, 2012. A copy is attached. This section discusses the effects of that Partnership Agreement on the way Department of

  13. Cladding Attachment Over Thick Exterior Insulating Sheathing

    SciTech Connect (OSTI)

    Baker, P.; Eng, P.; Lepage, R.

    2014-01-01

    The addition of insulation to the exterior of buildings is an effective means of increasing the thermal resistance of both wood framed walls as well as mass masonry wall assemblies. For thick layers of exterior insulation (levels greater than 1.5 inches), the use of wood furring strips attached through the insulation back to the structure has been used by many contractors and designers as a means to provide a convenient cladding attachment location (Straube and Smegal 2009, Pettit 2009, Joyce 2009, Ueno 2010). The research presented in this report is intended to help develop a better understanding of the system mechanics involved and the potential for environmental exposure induced movement between the furring strip and the framing. BSC sought to address the following research questions: 1. What are the relative roles of the mechanisms and the magnitudes of the force that influence the vertical displacement resistance of the system? 2. Can the capacity at a specified deflection be reliably calculated using mechanics based equations? 3. What are the impacts of environmental exposure on the vertical displacement of furring strips attached directly through insulation back to a wood structure?

  14. Cladding Attachment Over Thick Exterior Insulating Sheathing

    SciTech Connect (OSTI)

    Baker, P.; Eng, P.; Lepage, R.

    2014-01-01

    The addition of insulation to the exterior of buildings is an effective means of increasing the thermal resistance of both wood framed walls as well as mass masonry wall assemblies. For thick layers of exterior insulation (levels greater than 1.5 inches), the use of wood furring strips attached through the insulation back to the structure has been used by many contractors and designers as a means to provide a convenient cladding attachment location (Straube and Smegal 2009, Pettit 2009, Joyce 2009, Ueno 2010). The research presented in this report is intended to help develop a better understanding of the system mechanics involved and the potential for environmental exposure induced movement between the furring strip and the framing. BSC sought to address the following research questions: 1.What are the relative roles of the mechanisms and the magnitudes of the force that influence the vertical displacement resistance of the system? 2.Can the capacity at a specified deflection be reliably calculated using mechanics based equations? 3.What are the impacts of environmental exposure on the vertical displacement of furring strips attached directly through insulation back to a wood structure?

  15. Attachment FY2011-06 OPAM | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    SUMMARY OF PUBLIC LAW 111-240, THE SMALL BUSINESS JOBS ACT OF 2010 Attachment FY2011-06 OPAM More Documents & Publications Attachment FY2011-28 OPAM Chapter 19 - Small Business...

  16. Attachment FY2011-9 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Attachment FY2011-9 Attachment FY2011-9 FFRDC Determination for a Contract Competition More Documents & Publications Policy Flash 2013-30 Acquisition Letter on Acquisition Planning...

  17. Attachment FY2011-12 | Department of Energy

    Office of Environmental Management (EM)

    2 Attachment FY2011-12 Indirect Cost Rate Administration Attachment FY2011-12 More Documents & Publications AcqGuide42pt1.doc&0; Acquisition Letter No. AL 2008-02 Department of...

  18. AttachmentFlash_2010-65.pdf | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    65.pdf AttachmentFlash2010-65.pdf PDF icon AttachmentFlash2010-65.pdf More Documents & Publications fac2001-26.pdf DOELabor Leadership Roundtable Meeting Generic copy of DOE's...

  19. Dual-shank attachment design for omega seals

    DOE Patents [OSTI]

    Sattinger, Stanley S.

    1978-01-01

    An improved apparatus and process for attaching welded omega seal segments to reactor heads, standpipes, mechanisms, and plugs comprises a first shank in combination with a second shank to attach an omega seal at a metal-to-metal interface.

  20. EECBG SEP Attachment 1 - Process metric list | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SEP Attachment 1 - Process metric list EECBG SEP Attachment 1 - Process metric list Reporting Guidance Process Metric List eecbg_10_07b_sep__10_006a_attachment1_process_metric_list.pdf (93.56 KB) More Documents & Publications EECBG 10-07C/SEP 10-006B Attachment 1: Process Metrics List EECBG Program Notice 10-07A DOE Recovery Act Reporting Requirements for the State Energy Program

  1. Cable attachment for a radioactive brachytherapy source capsule

    DOE Patents [OSTI]

    Gross, Ian G; Pierce, Larry A

    2006-07-18

    In cancer brachytherapy treatment, a small californium-252 neutron source capsule is attached to a guide cable using a modified crimping technique. The guide cable has a solid cylindrical end, and the attachment employs circumferential grooves micromachined in the solid cable end. The attachment was designed and tested, and hardware fabricated for use inside a radioactive hot cell. A welding step typically required in other cable attachments is avoided.

  2. Attachment 3.a. Part A Page 1 of 6

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ......... 3 A.7. Billing & Payment ......of the requesting agency and servicing agency. A.7. Billing & Payment Attachment 3.a. ...

  3. Standard Financing Offer Template (IDIQ Attachment J-12) | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Standard Financing Offer Template (IDIQ Attachment J-12) Standard Financing Offer Template (IDIQ Attachment J-12) Document features a template to help communicate a finance offer as part of an energy savings performance contract. Download the standard financing offer template. (30.52 KB) More Documents & Publications Investor Deal Summary Template (IDIQ Attachment J-11) ESPC Task Order Financial Schedules (IDIQ Attachment J-6) Descriptions of ESPC Task Order Schedules and

  4. SECTION L -ATTACHMENT B - LISTING OF KEY PERSONNEL

    National Nuclear Security Administration (NNSA)

    B, Page 1 SECTION L ATTACHMENT B LISTING OF KEY PERSONNEL TITLE NAME Note: Addremove extra rows if needed...

  5. Photoswitchable method for the ordered attachment of proteins to surfaces

    DOE Patents [OSTI]

    Camarero, Julio A.; De Yoreo, James J.; Kwon, Youngeun

    2010-04-20

    Described herein is a method for the attachment of proteins to any solid support with control over the orientation of the attachment. The method is extremely efficient, not requiring the previous purification of the protein to be attached, and can be activated by UV-light. Spatially addressable arrays of multiple protein components can be generated by using standard photolithographic techniques.

  6. Photoswitchable method for the ordered attachment of proteins to surfaces

    DOE Patents [OSTI]

    Camarero, Julio A.; DeYoreo, James J.; Kwon, Youngeun

    2011-07-05

    Described herein is a method for the attachment of proteins to any solid support with control over the orientation of the attachment. The method is extremely efficient, not requiring the previous purification of the protein to be attached, and can be activated by UV-light. Spatially addressable arrays of multiple protein components can be generated by using standard photolithographic techniques.

  7. ATTACHMENT A - CHECKLIST FOR SELF ASSESSMENT | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ATTACHMENT A - CHECKLIST FOR SELF ASSESSMENT ATTACHMENT A - CHECKLIST FOR SELF ASSESSMENT ATTACHMENT A - CHECKLIST FOR SELF ASSESSMENT (302.66 KB) More Documents & Publications Assessment B - Program Criteria Assessment C-Site Visit Protocol DOE O 243.1B, Records Management Program

  8. Attachment 4: Unrevised SFO Paragraphs Reissued | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    4: Unrevised SFO Paragraphs Reissued Attachment 4: Unrevised SFO Paragraphs Reissued Unrevised SFO Paragraphs Reissued (35.68 KB) More Documents & Publications Attachment 2: Solicitation for Offers with New and Revised Green Lease Text Attachment 1: Green Lease Policies and Procedures for Lease Acquisition 1

  9. AL2000-10Attach.pdf | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AL2000-10Attach.pdf AL2000-10Attach.pdf PDF icon AL2000-10Attach.pdf More Documents & Publications AL2000-10R.pdf AL2004-01r2.pdf Consent Order, Fluor Federal Services - EA-2000-10...

  10. Microsoft Word - ATTACHMENT A Suppl 5.doc

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ATTACHMENT A: Modeling in Support of Additional Two-Unit Operating Configurations Unit 1 & Unit 2 Operation - SO2 Table Mirant Potomac, Alexandria, Virginia Maximum Impacts Predicted by AERMOD-PRIME Compliance Based on Highest, Second-Highest Short-term and Highest Annual Concentrations Units 1 & 2 on 24 hrs/day @ Max load SO2 = 0.31 lb/MBtu for both units. AERMOD- PRIME Monitored Background AERMOD-PRIME + Background NAAQS Distance Direction Ground Elevation Flagpole Elevation X (m) Y

  11. Appendix DATA Attachment A: WIPP Borehole Update

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    A: WIPP Borehole Update United States Department of Energy Waste Isolation Pilot Plant Carlsbad Field Office Carlsbad, New Mexico Appendix DATA-2014 Attachment A: WIPP Borehole Update Table of Contents DATA-A-1.0 WIPP Boreholes DATA-A-2.0 Individual Well Reports DATA-A-2.1 New Wells Drilled Since the CRA-2009 DATA-A-2.2 Plugged Wells DATA-A-3.0 References List of Tables Table DATA-A- 1. Status of WIPP Boreholes December 2012 WIPP Table DATA-A-1. Status of WIPP Boreholes December 2012 WIPP

  12. Microsoft Word - Attachment coversheet.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    HANFORD MISSION SUPPORT CONTRACT ADVANCE UNDERSTANDING ON COST REVISED DECEMBER 31, 2014 Mission Support Contract Contract Number DE-AC06-09RL14728 Attachment J, Section J.8 Modification 479 ii CHANGE HISTORY Version Date Change Author Change Summary 6.0 December 31, 2014 Ricky Churchman Updated to incorporate: Retention as a part of the Hiring/Signing bonuses 5.1 August 26, 2014 Ricky Churchman Updated to incorporate: Use of Government/Contractor Leased Vehicles for Offsite Transportation 5.0

  13. Predicting Envelope Leakage in Attached Dwellings

    SciTech Connect (OSTI)

    Faakye, O.; Arena, L.; Griffiths, D.

    2013-07-01

    The most common method for measuring air leakage is to use a single blower door to pressurize and/or depressurize the test unit. In detached housing, the test unit is the entire home and the single blower door measures air leakage to the outside. In attached housing, this 'single unit', 'total', or 'solo' test method measures both the air leakage between adjacent units through common surfaces as well air leakage to the outside. Measuring and minimizing this total leakage is recommended to avoid indoor air quality issues between units, reduce energy losses to the outside, reduce pressure differentials between units, and control stack effect. However, two significant limitations of the total leakage measurement in attached housing are: for retrofit work, if total leakage is assumed to be all to the outside, the energy benefits of air sealing can be significantly over predicted; for new construction, the total leakage values may result in failing to meet an energy-based house tightness program criterion. The scope of this research is to investigate an approach for developing a viable simplified algorithm that can be used by contractors to assess energy efficiency program qualification and/or compliance based upon solo test results.

  14. DOE/RL-92-36, Hanford Site Hoisting and Rigging Manual ATTACHMENTS

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ATTACHMENTS February 28, 2012 Rev 1 Page 31 ATTACHMENT 2 Lifting Requirements for Concrete Blocks DOERL-92-36, Hanford Site Hoisting and Rigging Manual ATTACHMENTS February 28,...

  15. Expert Meeting Report: Cladding Attachment Over Exterior Insulation (BSC Report)

    SciTech Connect (OSTI)

    2013-10-01

    The addition of insulation to the exterior of buildings is an effective means of increasing the thermal resistance of both wood framed walls as well as mass masonry wall assemblies. The location of the insulation to the exterior of the structure has many direct benefits including better effective R-value from reduced thermal bridging, better condensation resistance, reduced thermal stress on the structure, as well as other commonly associated improvements such as increased air tightness and improved water management (Hutcheon 1964, Lstiburek 2007). The intent of the meeting was to review the current state of industry knowledge regarding cladding attachment over exterior insulation with a specific focus on: 1. Gravity load resistance, 2. Wind load resistance. The presentations explore these topics from an engineering design, laboratory testing, field monitoring, as well as practical construction perspective. By bringing various groups together (who have been conduction research or have experience in this area), a more holistic review of the design limits and current code language proposals can be completed and additional gaps identified. The results of which will help inform design standards and criteria.

  16. High Performance Window Attachments | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (2.09 MB) More Documents & Publications Fenestration Software Tools Advanced Facades, Daylighting, and Complex Fenestration Systems OpenStudio - 2013 Peer Review

  17. Revised Merit Review Guide for Financial Assistance, JULY 2013

    Broader source: Energy.gov [DOE]

    The Merit Review Guide for Financial Assistance along with Attachments 2 and 3 of the Guide have been revised. Revisions include correcting references to attachments and updating of the information presented in the Guide and Attachments to reflect the new requirements of the Whistleblower Protection Enhancement Act of 2012. The revised documents can be found at http://energy.gov/management/downloads/policy-flash-2013-38-revised-meri... and are labeled: Merit Review Guide FINAL JULY 2013, ATTACHMENT 2 Sample COI ADDED WB LANGUAGE JULY 2013.docx and ATTACHMENT 3 - Sample Evaluation and Selection Plan JULY 2013.docx.

  18. Dissociative electron attachment studies on acetone

    SciTech Connect (OSTI)

    Prabhudesai, Vaibhav S. Tadsare, Vishvesh; Ghosh, Sanat; Gope, Krishnendu; Davis, Daly; Krishnakumar, E.

    2014-10-28

    Dissociative electron attachment (DEA) to acetone is studied in terms of the absolute cross section for various fragment channels in the electron energy range of 020 eV. H{sup ?} is found to be the most dominant fragment followed by O{sup ?} and OH{sup ?} with only one resonance peak between 8 and 9 eV. The DEA dynamics is studied by measuring the angular distribution and kinetic energy distribution of fragment anions using Velocity Slice Imaging technique. The kinetic energy and angular distribution of H{sup ?} and O{sup ?} fragments suggest a many body break-up for the lone resonance observed. The ab initio calculations show that electron is captured in the multi-centered anti-bonding molecular orbital which would lead to a many body break-up of the resonance.

  19. Vacuum die attach for integrated circuits

    DOE Patents [OSTI]

    Schmitt, Edward H.; Tuckerman, David B.

    1991-01-01

    A thin film eutectic bond for attaching an integrated circuit die to a circuit substrate is formed by coating at least one bonding surface on the die and substrate with an alloying metal, assembling the die and substrate under compression loading, and heating the assembly to an alloying temperature in a vacuum. A very thin bond, 10 microns or less, which is substantially void free, is produced. These bonds have high reliability, good heat and electrical conduction, and high temperature tolerance. The bonds are formed in a vacuum chamber, using a positioning and loading fixture to compression load the die, and an IR lamp or other heat source. For bonding a silicon die to a silicon substrate, a gold silicon alloy bond is used. Multiple dies can be bonded simultaneously. No scrubbing is required.

  20. Vacuum die attach for integrated circuits

    DOE Patents [OSTI]

    Schmitt, E.H.; Tuckerman, D.B.

    1991-09-10

    A thin film eutectic bond for attaching an integrated circuit die to a circuit substrate is formed by coating at least one bonding surface on the die and substrate with an alloying metal, assembling the die and substrate under compression loading, and heating the assembly to an alloying temperature in a vacuum. A very thin bond, 10 microns or less, which is substantially void free, is produced. These bonds have high reliability, good heat and electrical conduction, and high temperature tolerance. The bonds are formed in a vacuum chamber, using a positioning and loading fixture to compression load the die, and an IR lamp or other heat source. For bonding a silicon die to a silicon substrate, a gold silicon alloy bond is used. Multiple dies can be bonded simultaneously. No scrubbing is required. 1 figure.

  1. Microsoft Word - Flash2008-09Attachment.doc | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    9Attachment.doc More Documents & Publications Flash2007-02Attachment.doc&0; Microsoft Word - AL2000-05Attachment.doc Flash2007-03Attachment.doc&0;...

  2. Microsoft Word - AL2000-05Attachment.doc | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Attachment.doc Microsoft Word - AL2000-05Attachment.doc PDF icon Microsoft Word - AL2000-05Attachment.doc More Documents & Publications al99-06attachment.doc&0; EXHIBIT A: CRADA,...

  3. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Table of Contents

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    III SECTION J LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS TABLE OF CONTENTS Document Title Page Attachment A Personnel (Appendix A) ......................................................................................... ..3 Attachment B Key Personnel ......................................................................................................... 26 Attachment C Small Business Subcontracting Plan ...................................................................... 27

  4. Microsoft Word - Attachment J-5 Continuity of Operations Plan.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5-1 ATTACHMENT J.5 CONTINUITY OF OPERATIONS

  5. Investor Deal Summary Template (IDIQ Attachment J-11) | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Investor Deal Summary Template (IDIQ Attachment J-11) Investor Deal Summary Template (IDIQ Attachment J-11) Document features a template for summarizing an investor or energy service company's deal as part of an energy savings performance contract. Download the Investor Deal Summary Template. (39.05 KB) More Documents & Publications ESPC Task Order Financial Schedules (IDIQ Attachment J-6) ESPC ENABLE Final Proposal Requirements Model Energy Savings Performance Contract,

  6. Certification and Rating of Attachments for Fenestration Technologies

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (DE-FOA-0001000) | Department of Energy Certification and Rating of Attachments for Fenestration Technologies (DE-FOA-0001000) Certification and Rating of Attachments for Fenestration Technologies (DE-FOA-0001000) November 5, 2013 - 4:43pm Addthis This funding opportunity is closed Through this Funding Opportunity Announcement (FOA) the Building Technologies Office (BTO) seeks to establish a performance rating mechanism for assessing the energy performance of fenestration attachments. DOE

  7. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachment E

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    E DE-AC36-08GO28308 Modification M1033 Attachment E Applicable Laws and Regulations (List A) Necessary and Sufficient Environmental, Safety and Health Standards CODE OF FEDERAL REGULATIONS (CFR) 7 CFR 340-Biotechnology Permits 10 CFR 8.4 - Interpretation by the General Counsel: AEC Jurisdiction 10 CFR 707 Workplace Substance Abuse Programs at DOE Sites 10 CFR 719 - Contractor Legal Management Requirements 10 CFR 835 - Occupational Radiation Protection 10 CFR 851 - Worker Safety and Health

  8. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachment F

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    F DE-AC36-08GO28308 Modification M1033 Attachment F Operating and Administrative Requirements (List B) Prime Contract No. DE-AC36-08GO28308 The operating and administrative requirements, including the Contractor Requirements Documents of DOE directives listed below are applicable in whole or in part in accordance with clauses H-18 Application of DOE Contractor Requirements Documents and 970.5204-2, Laws, Regulations, and DOE Directives (DEC 2000). The concurrence analysis documenting

  9. Microsoft Word - Policy Flash 2010-82 Attachment 1 | Department...

    Broader source: Energy.gov (indexed) [DOE]

    2 Attachment 1 More Documents & Publications Policy Flash 2010-82 Microsoft Word - Policy Flash 2008-07.doc Microsoft Word - Policy Flash 2008-10.doc...

  10. FLASH2003-12attachment.pdf | Department of Energy

    Office of Environmental Management (EM)

    FLASH2003-12attachment.pdf More Documents & Publications Flash2004-19.pdf Document DOE Princeton Plasma Physics Laboratory Purchase Power Agreement Request for Proposal...

  11. Nevada Test Site Environmental Report Attachment A: Site Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Nevada Test Site Environmental Report Attachment A: Site Description DOENV25946--790-ATT A Nevada Test Site Environmental Report 2008 Disclaimer Reference herein to any specific ...

  12. SECTION L -ATTACHMENT B - LISTING OF KEY PERSONNEL

    National Nuclear Security Administration (NNSA)

    B, Page 1 SECTION L ATTACHMENT B LISTING OF KEY PERSONNEL TITLE NAME [Note: Add/remove extra rows if needed]

  13. Building America Case Study:Cladding Attachment Over Mineral...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Cladding Attachment Over Mineral Fiber Insulation Board Ontario, Canada PROJECT INFORMATION Project Name: Climate-Exposed Long- Term Testing of Mineral Fiber Insulation Board Under ...

  14. Building America Expert Meeting: Cladding Attachment Over Exterior Insulation

    Broader source: Energy.gov [DOE]

    This expert meeting was conducted by Building Science Corporation on July 28, 2012 and focused on issues surrounding cladding attachment and performance of walls with exterior insulating sheathing.

  15. Attachment 3 b. Part A Page 1 of 6

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Attachment 3 b. Part A Page 1 of 6 Section A - General Terms and Conditions ................................................................................................ 2 A.1. Purpose .................................................................................................................................................. 2 A.2. Authority ............................................................................................................................................... 2

  16. Microsoft Word - Attachment G1H.doc

    Office of Environmental Management (EM)

    APPENDIX H DESIGN DRAWINGS PANEL CLOSURE SYSTEM WASTE ISOLATION PILOT PLANT CARLSBAD, NEW ... ATTACHMENT G1 APPENDIX H DESIGN DRAWINGS PANEL CLOSURE SYSTEM WASTE ISOLATION PILOT PLANT ...

  17. Vacuum Attachment for Collection of Lithium Powder ---- Inventor...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of Lithium Powder ---- Inventor(s) Hans Schneider and Stephan Jurczynski The Vacuum Attachment is part of an integrated system designed to collect Lithium (Li) Power for ...

  18. Appendix DATA Attachment B: WIPP Waste Containers and Emplacement

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Carlsbad Field Office Carlsbad, New Mexico Appendix DATA-2014 Attachment B: WIPP Waste Containers and Emplacement Table of Contents DATA-B-1.0 Authorized Waste Emplacement ...

  19. Attachment 2: Solicitation for Offers with New and Revised Green...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2: Solicitation for Offers with New and Revised Green Lease Text Attachment 2: Solicitation for Offers with New and Revised Green Lease Text Solicitation for Offers Paragraphs with ...

  20. Attachment 3: Instructions for Use of Green Lease Solicitation...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3: Instructions for Use of Green Lease Solicitation Paragraph Reference Chart Attachment 3: Instructions for Use of Green Lease Solicitation Paragraph Reference Chart (1.84 MB) ...

  1. Attachment 1: Green Lease Policies and Procedures for Lease Acquisitio...

    Broader source: Energy.gov (indexed) [DOE]

    Green Lease Policies and Procedures for Lease Acquisition Attachment 2: Solicitation for Offers with New and Revised Green Lease Text Energy Efficiency in Separate Tenant Spaces - ...

  2. Attachment 3: Instructions for Use of Green Lease Solicitation Paragraph

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Reference Chart | Department of Energy 3: Instructions for Use of Green Lease Solicitation Paragraph Reference Chart Attachment 3: Instructions for Use of Green Lease Solicitation Paragraph Reference Chart (1.84 MB) More Documents & Publications Green Lease Policies and Procedures for Lease Acquisition Attachment 1: Green Lease Policies and Procedures for Lease Acquisition Microsoft Word - AL2008-05.doc

  3. DE-SOL-0002555 WIPP Solicitation J-33 PART III - LIST OF DOCUMENTS, EXHIBITS AND OTHER ATTACHMENTS

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 PART III - LIST OF DOCUMENTS, EXHIBITS AND OTHER ATTACHMENTS SECTION J ATTACHMENT H: RESERVED

  4. Part VII: Section J - List of Documents, Exhibits, and Other Attachments, Attachment U

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    U DE-AC36-08GO28308 Modification M1033 Attachment U Treaties and International Agreements Intellectual property rights for subject inventions made under NREL's award under the JCERDC will be allocated as set forth in the Agreement between the Department of Energy of the United States of America and the Government of the Republic of India of November 4, 2010 for Cooperation on a Joint Clean Energy Research and Development Center (JCERDC), and its "Project Annex on Intellectual Property

  5. Policy Flash 2013-38 Revised Merit Review Guide For Financial...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    8 Revised Merit Review Guide For Financial Assistance Policy Flash 2013-38 Revised Merit Review Guide For Financial Assistance Attached is Policy Flash 2013-38 Revised Merit Review ...

  6. Microsoft Word - Attachment G2E.doc

    Office of Environmental Management (EM)

    E DESIGN DRAWINGS SHAFT SEALING SYSTEM COMPLIANCE SUBMITTAL DESIGN REPORT Waste Isolation Pilot Plant Hazardous Waste Permit November 30, 2010 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit November 30, 2010 PERMIT ATTACHMENT G2E Page G2E-1 of 38 1 Waste Isolation Pilot Plant Hazardous Waste Permit November 30, 2010 PERMIT ATTACHMENT G2E Page G2E-2 of 38 1 Waste Isolation Pilot Plant Hazardous Waste Permit November 30, 2010 PERMIT ATTACHMENT G2E Page G2E-3 of

  7. DE-SOL-0008449 Attachment L-2b

    National Nuclear Security Administration (NNSA)

    level testing for NSDD Core installations DE-SOL-0008449 Attachment L-2b [Submit in Volume II, TAB 1] Instructions Attachment L-2b: Note: Attachment L-1a is limited to one (1) 8 ½ x 11 page limit. Experiences provided must be relevant to the work that the team member will be performing under this contract. The Offeror shall explain how the work performed by the experience is relevant to the indicator. Relevance is defined by Indicator as follows: A. Relevance to indicator A. is defined as

  8. Protocol EM-HQ Review Field Self Assessment Site Specific QAP...

    Office of Environmental Management (EM)

    The referenced attachment can be found at on the Environmental Management website via the Standard Review Plan (Quality Assurance Section) at the following link: http:...

  9. Attachment FY2011-58 OPAM | Department of Energy

    Energy Savers [EERE]

    INFORMATION REPORTING Attachment FY2011-58 OPAM More Documents & Publications Chapter 35 - Research and Development Contracting AcqGuide35pt1rev2.doc&0; Federal Assistance...

  10. Microsoft Word - Policy Flash 2010-78 Attachment 1 Unsuccessful...

    Office of Environmental Management (EM)

    1 Unsuccessful Offeror Letter Template-Final 8-17-10 Microsoft Word - Policy Flash 2010-78 Attachment 1 Unsuccessful Offeror Letter Template-Final 8-17-10 Microsoft Word -...

  11. Microsoft Word - Policy Flash 2010-78 Attachment 3 Conflicts...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    3 Conflicts of Interest Cert- template-Final 8-17-10 Microsoft Word - Policy Flash 2010-78 Attachment 3 Conflicts of Interest Cert- template-Final 8-17-10 Microsoft Word -...

  12. Microsoft Word - Policy Flash 2010-78 Attachment 2 Confidentiality...

    Energy Savers [EERE]

    2 Confidentiality Cert template-Final 8-17-10 Microsoft Word - Policy Flash 2010-78 Attachment 2 Confidentiality Cert template-Final 8-17-10 Microsoft Word - Policy Flash...

  13. Microsoft Word - Policy Flash 2010-78 Attachment 4 Successful...

    Office of Environmental Management (EM)

    4 Successful Offeror Letter Template-Final 8-17-10 Microsoft Word - Policy Flash 2010-78 Attachment 4 Successful Offeror Letter Template-Final 8-17-10 Microsoft Word - Policy...

  14. River Corridor Closure Contract Section J, Attachment J-13

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 Contract No. DE-AC06-08RL14655 A000 1 ATTACHMENT J-13 HANFORD SITE SERVICES Hanford Site Services are divided into three categories: Category 1: DOE will provide these Mandatory...

  15. Attachment FY2011-31 OPAM | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    attachment 3 flow chart of new 17.5 FAR Team update based on FAC2005-47 Dec 13, 2010 More Documents & Publications Flash2011-31 OPAM Flash2011-26 OPAM ATTACHMENTFLASH2011-26-OPAM...

  16. Microsoft Word - Attachment J-2 Hardware and Software System...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    J-2-1 ATTACHMENT J.2 HARDWARE AND SOFTWARE SYSTEM REQUIREMENTS a. The Contractor shall provide a DOD 5015.x compliant individual electronic file system for each open claim in ...

  17. Microsoft Word - Attachment G2B.doc

    Office of Environmental Management (EM)

    B SHAFT SEALING CONSTRUCTION PROCEDURES SHAFT SEALING SYSTEM COMPLIANCE SUBMITTAL DESIGN REPORT Waste Isolation Pilot Plant Hazardous Waste Permit November 30, 2010 (This page intentionally blank) Waste Isolation Pilot Plant Hazardous Waste Permit November 30, 2010 PERMIT ATTACHMENT G2B Page G2B-i ATTACHMENT G2 APPENDIX B SHAFT SEALING CONSTRUCTION PROCEDURES SHAFT SEALING SYSTEM COMPLIANCE SUBMITTAL DESIGN REPORT Appendix B Abstract This appendix describes equipment and procedures used to

  18. River Corridor Closure Contract Section J, Attachment J-6

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6 Contract No. DE-AC06-05RL14655 Mod 459 1 ATTACHMENT J-6 ADVANCE AGREEMENT, PERSONNEL, AND RELATED COSTS This attachment will be prepared subsequent to Contract award pursuant to Clause H.15, Advance Understanding on Costs. The advance understandings listed below are subject to the specific limitations, conditions, and exclusions of subpart 31.2 of FAR as supplemented by Department of Energy Acquisition Regulation (DEAR) 931.2. TYPE OF COST ALLOWABILITY CLARIFICATION Beryllium Testing/Travel

  19. PART III -LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Occupational Medical Services at Hanford J-2-1 Section J Attachment J-2 LIST OF APPLICABLE DOE DIRECTIVES - LIST B The DOE Directives listed below contain requirements relevant to the scope of work under this contract. In most cases, the requirements applicable to the Contractor are contained in the Contractor Requirement Document attached to the DOE directive. These directives are applicable, in whole or in part, in accordance with Section I Clause entitled "DEAR 970.5204-2 LAWS,

  20. Pressurizer with a mechanically attached surge nozzle thermal sleeve

    SciTech Connect (OSTI)

    Wepfer, Robert M

    2014-03-25

    A thermal sleeve is mechanically attached to the bore of a surge nozzle of a pressurizer for the primary circuit of a pressurized water reactor steam generating system. The thermal sleeve is attached with a series of keys and slots which maintain the thermal sleeve centered in the nozzle while permitting thermal growth and restricting flow between the sleeve and the interior wall of the nozzle.

  1. Attachment F - Bibliography and References | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    F - Bibliography and References Attachment F - Bibliography and References These documents are listed in Attachment F - Bibliography and References section of the Phase 2 Radiological Release Accident Investigation Report. DOE Order 225.1B, Accident Investigations, March 4, 2011 DOE Order 226.1B, Implementation of Department of Energy Oversight Policy, April 25, 2011 DOE Order 422.1, Conduct of Operations, June 29, 2010 DOE Order 426.1, Federal Technical Capability, November 19, 2009 DOE Manual

  2. Attachment 1: Green Lease Policies and Procedures for Lease Acquisition |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy 1: Green Lease Policies and Procedures for Lease Acquisition Attachment 1: Green Lease Policies and Procedures for Lease Acquisition Green Lease Policies and Procedures for Lease Acquisition (45.31 KB) More Documents & Publications Green Lease Policies and Procedures for Lease Acquisition Attachment 2: Solicitation for Offers with New and Revised Green Lease Text Energy Efficiency in Separate Tenant Spaces - A Feasibility Study

  3. Attachment I: Approval of Agreement-in-Principal with the State of Alaska |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy I: Approval of Agreement-in-Principal with the State of Alaska Attachment I: Approval of Agreement-in-Principal with the State of Alaska US Department of Energy Memorandum DATE: January 31, 1995 REPLY TO ATTN OF: EM-22 (C. Smoot, 202/586-2352) SUBJECT: Approval of Agreement-in-Principle with the State of Alaska TO: Manager, Nevada Operations Office Thank you for providing the draft Agreement-in-Principle with the State of Alaska for review and approval. I approve the

  4. Microsoft Word - Flash2008-08attachmentFAC22.doc | Department...

    Energy Savers [EERE]

    Flash2008-08attachmentFAC22.doc Microsoft Word - Flash2008-08attachmentFAC22.doc Microsoft Word - Flash2008-08attachmentFAC22.doc More Documents & Publications Policy Flash 2013-75...

  5. Attachment A: Modeling in Support of Additional Two-Unit Operating...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Attachment A: Modeling in Support of Additional Two-Unit Operating Configurations Attachment A: Modeling in Support of Additional Two-Unit Operating Configurations Docket No. ...

  6. Biocompatible implants and methods of making and attaching the same

    DOE Patents [OSTI]

    Rowley, Adrian P; Laude, Lucien D; Humayun, Mark S; Weiland, James D; Lotfi, Atoosa; Markland, Jr., Francis S

    2014-10-07

    The invention provides a biocompatible silicone implant that can be securely affixed to living tissue through interaction with integral membrane proteins (integrins). A silicone article containing a laser-activated surface is utilized to make the implant. One example is an implantable prosthesis to treat blindness caused by outer retinal degenerative diseases. The device bypasses damaged photoreceptors and electrically stimulates the undamaged neurons of the retina. Electrical stimulation is achieved using a silicone microelectrode array (MEA). A safe, protein adhesive is used in attaching the MEA to the retinal surface and assist in alleviating focal pressure effects. Methods of making and attaching such implants are also provided.

  7. Apparatus for attaching a cleaning tool to a robotic manipulator

    DOE Patents [OSTI]

    Killian, M.A.; Zollinger, W.T.

    1991-01-01

    This invention is comprised of an apparatus for connecting a cleaning tool to a robotic manipulator so that the tool can be used in contaminated areas on horizontal, vertical and sloped surfaces. The apparatus comprises a frame and a handle, with casters on the frame to facilitate movement. The handle is pivotally and releasibly attached to the frame at a preselected position of a plurality of attachment positions. The apparatus is specifically configured for the KELLY VACUUM SYSTEM but can be modified for use with any standard mobile robot and cleaning tool.

  8. Part III - List of Documents, Exhibits, and Other Attachments

    National Nuclear Security Administration (NNSA)

    Updated 9/30/15 to Mod 0588 Contract No. DE-AC04-94AL85000 Modification No. M202 Section J - Page 1 Part III - List of Documents, Exhibits, and Other Attachments Section J LIST OF ATTACHMENTS Document Appendix A - Personnel Appendix (Revised RAs 1-12 and Mods M0541, M0558) Appendix B - Statement of Work (Revised M244, M264) Appendix C - Special Bank Account Agreement (Revised M248, M271, M461, M497, M508) Appendix D - Key Personnel (Revised M216, M224, M227, M229, M233, M252, M257, M272, M275,

  9. Section L - Attachment D - Past-Performance Information Form

    National Nuclear Security Administration (NNSA)

    L, Attachment E, Page 1 SECTION L ATTACHMENT E PAST PERFORMANCE INFORMATION FORM 1. Complete Name of Offeror or Team Member 2. Contract Title and Location 3. Customer Name, Current Address, Telephone Number and E-mail 4. Contract Number and Type of Contract 5. Date of Contract Award 6. Date Work Commenced 7. Date the Work was Completed 8. Initial Contract Price /Estimated Cost and Fee 9. Final Amount Invoiced/Amount Invoiced to Date 10a. Technical Point of Contact (see instruction below) 10b.

  10. Apparatus for attaching a cleaning tool to a robotic manipulator

    DOE Patents [OSTI]

    Killian, M.A.; Zollinger, W.T.

    1992-09-22

    An apparatus is described for connecting a cleaning tool to a robotic manipulator so that the tool can be used in contaminated areas on horizontal, vertical and sloped surfaces. The apparatus comprises a frame and a handle, with casters on the frame to facilitate movement. The handle is pivotally and releasibly attached to the frame at a preselected position of a plurality of attachment positions. The apparatus is specifically configured for the Kelly Vacuum System but can be modified for use with any standard mobile robot and cleaning tool. 14 figs.

  11. Section L - Attachment D - Past-Performance Information Form

    National Nuclear Security Administration (NNSA)

    L, Attachment E, Page 1 SECTION L ATTACHMENT E PAST PERFORMANCE INFORMATION FORM 1. Complete Name of Offeror or Team Member 2. Contract Title and Location 3. Customer Name, Current Address, Telephone Number and E-mail 4. Contract Number and Type of Contract 5. Date of Contract Award 6. Date Work Commenced 7. Date the Work was Completed 8. Initial Contract Price /Estimated Cost and Fee 9. Final Amount Invoiced/Amount Invoiced to Date 10a. Technical Point of Contact (see instruction below) 10b.

  12. Interface structure for hub and mass attachment in flywheel rotors

    DOE Patents [OSTI]

    Deteresa, Steven J.; Groves, Scott E.

    1998-06-02

    An interface structure for hub and mass attachment in flywheel rotors. The interface structure efficiently transmits high radial compression forces and withstands both large circumferential elongation and local stresses generated by mass-loading and hub attachments. The interface structure is comprised of high-strength fiber, such as glass and carbon, woven into an angle pattern which is about 45.degree. with respect to the rotor axis. The woven fiber is bonded by a ductile matrix material which is compatible with and adheres to the rotor material. This woven fiber is able to elongate in the circumferential direction to match the rotor growth during spinning.

  13. Interface structure for hub and mass attachment in flywheel rotors

    DOE Patents [OSTI]

    Deteresa, S.J.; Groves, S.E.

    1998-06-02

    An interface structure is described for hub and mass attachment in flywheel rotors. The interface structure efficiently transmits high radial compression forces and withstands both large circumferential elongation and local stresses generated by mass-loading and hub attachments. The interface structure is comprised of high-strength fiber, such as glass and carbon, woven into an angle pattern which is about 45{degree} with respect to the rotor axis. The woven fiber is bonded by a ductile matrix material which is compatible with and adheres to the rotor material. This woven fiber is able to elongate in the circumferential direction to match the rotor growth during spinning. 2 figs.

  14. Reliability Testing the Die-Attach of CPV Cell Assemblies

    SciTech Connect (OSTI)

    Bosco, N.; Sweet, C.; Kurtz, S.

    2011-02-01

    Results and progress are reported for a course of work to establish an efficient reliability test for the die-attach of CPV cell assemblies. Test vehicle design consists of a ~1 cm2 multijunction cell attached to a substrate via several processes. A thermal cycling sequence is developed in a test-to-failure protocol. Methods of detecting a failed or failing joint are prerequisite for this work; therefore both in-situ and non-destructive methods, including infrared imaging techniques, are being explored as a method to quickly detect non-ideal or failing bonds.

  15. Appendix DATA Attachment B: WIPP Waste Containers and Emplacement

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Attachment B: WIPP Waste Containers and Emplacement United States Department of Energy Waste Isolation Pilot Plant Carlsbad Field Office Carlsbad, New Mexico Appendix DATA-2014 Attachment B: WIPP Waste Containers and Emplacement Table of Contents DATA-B-1.0 Authorized Waste Emplacement Containers DATA-B-1.1 Container Descriptions DATA-B-1.2 Dunnage Containers DATA-B-1.3 Payload Descriptions DATA-B-1.4 Emplacement Configurations DATA-B-2.0 References List of Figures Figure DATA-B- 1. 55-gal Drum

  16. Apparatus for attaching a cleaning tool to a robotic manipulator

    DOE Patents [OSTI]

    Killian, Mark A.; Zollinger, W. Thor

    1992-01-01

    An apparatus for connecting a cleaning tool to a robotic manipulator so that the tool can be used in contaminated areas on horizontal, vertical and sloped surfaces. The apparatus comprises a frame and a handle, with casters on the frame to facilitate movement. The handle is pivotally and releasibly attached to the frame at a preselected position of a plurality of attachment positions. The apparatus is specifically configured for the KELLY VACUUM SYSTEM but can be modified for use with any standard mobile robot and cleaning tool.

  17. Method for detecting pathogens attached to specific antibodies

    DOE Patents [OSTI]

    Miles, Robin R.; Venkateswaran, Kodumudi S.; Fuller, Christopher K.

    2005-01-25

    The use of impedance measurements to detect the presence of pathogens attached to antibody-coated beads. In a fluidic device antibodies are immobilized on a surface of a patterned interdigitated electrode. Pathogens in a sample fluid streaming past the electrode attach to the immobilized antibodies, which produces a change in impedance between two adjacent electrodes, which impedance change is measured and used to detect the presence of a pathogen. To amplify the signal, beads coated with antibodies are introduced and the beads would stick to the pathogen causing a greater change in impedance between the two adjacent electrodes.

  18. Impedance measurements for detecting pathogens attached to antibodies

    DOE Patents [OSTI]

    Miles, Robin R.; Venkateswaran, Kodumudi S.; Fuller, Christopher K.

    2004-12-28

    The use of impedance measurements to detect the presence of pathogens attached to antibody-coated beads. In a fluidic device antibodies are immobilized on a surface of a patterned interdigitated electrode. Pathogens in a sample fluid streaming past the electrode attach to the immobilized antibodies, which produces a change in impedance between two adjacent electrodes, which impedance change is measured and used to detect the presence of a pathogen. To amplify the signal, beads coated with antibodies are introduced and the beads would stick to the pathogen causing a greater change in impedance between the two adjacent electrodes.

  19. Methods and materials for nanocrystalline surface coatings and attachment of peptide amphiphile nanofibers thereon

    DOE Patents [OSTI]

    Stupp, Samuel I.; Spoerke, Erik D.; Anthony, Shawn G.; Niece; Krista L.

    2008-06-24

    Biocompatible composites comprising peptide amphiphiles and surface modified substrates and related methods for attachment thereon.

  20. Attached-sunspace designs: a nationwide economic appraisal

    SciTech Connect (OSTI)

    Roach, F.; Kirschner, C.

    1980-01-01

    Performance estimates for attached-sunspace passive solar heated residences have recently been incorporated into the Los Alamos/UNM EASE III model. These estimates are used to analyze the economic performance of a fixed dimension sunspace design when attached to a pre-existing single family residential unit. The sunspace is a passive design which can be easily and effectively adapted to a retrofit situation. Several key parameters are carefully evaluated for the sunspace retrofit design. These include loan or mortgage terms, ownership period, resale potential and competing conventional fuel prices. General economic and design parameters are combined in a variant of life cycle costing to evaluate the feasibility of both owner-built and contractor-built attached sunspaces for 220 regions in the contiguous United States. This evaluation is made for two conventional fuel types - natural gas and electric resistance - and for three resale values - 0%, 100%, and 200%. Results show that the prospect for conventional fuel displacement through retrofit of attached sunspaces is very good with the design's economic performance enhanced in regions with expensive conventional fuel alternatives.

  1. River Corridor Closure Contract Section J, Attachment J-8

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    8 Contract No. DE-AC06-05RL14655 A000 1 ATTACHMENT J-8 EMPLOYEE BENEFITS AND PENSION PLANS Pursuant to application employee benefit and pension requirements in Contract Section H, Special Contract Requirement, the Contractor shall annually submit the Report of Contractor Expenditures for Employee Supplemental Compensation

  2. New methods of nozzle attachment to FRP spray headers

    SciTech Connect (OSTI)

    Boucher, E.J.

    1995-06-01

    The traditional method of attaching spray nozzles to FRP spray headers in the absorber tower of a wet limestone system has been through the use of 150 lb. Flanges. This paper will illustrate two additional methods (grooved adapters & adhesive bonded nozzles) and will demonstrate the cost saving associated versus the flanged option, as well as the advantages and disadvantages of each system.

  3. Shunt attachment and method for interfacing current collection systems

    DOE Patents [OSTI]

    Denney, Paul E. (State College, PA); Iyer, Natraj C. (Columbia, SC); Hannan, III, William F. (Monroeville Boro, PA)

    1992-01-01

    A composite brush to shunt attachment wherein a volatile component of a composite but mostly metallic brush, used for current collection purposes, does not upon welding or brazing, adversely affect the formation of the interfacial bond with a conductive shunt which carries the current from the zone of the brush. The brush to shunt attachment for a brush material of copper-graphite composite and a shunt of copper, or substituting silver for copper as an alternative, is made through a hot isostatic pressing (HIP). The HIP process includes applying high pressure and temperature simultaneously at the brush to shunt interface, after it has been isolated or canned in a metal casing in which the air adjacent to the interface has been evacuated and the interfacial area has been sealed before the application of pressure and temperature.

  4. Shunt attachment and method for interfacing current collection systems

    DOE Patents [OSTI]

    Denney, P.E.; Iyer, N.C.; Hannan, W.F. III.

    1992-12-08

    A composite brush to shunt attachment wherein a volatile component of a composite but mostly metallic brush, used for current collection purposes, does not upon welding or brazing, adversely affect the formation of the interfacial bond with a conductive shunt which carries the current from the zone of the brush. The brush to shunt attachment for a brush material of copper-graphite composite and a shunt of copper, or substituting silver for copper as an alternative, is made through a hot isostatic pressing (HIP). The HIP process includes applying high pressure and temperature simultaneously at the brush to shunt interface, after it has been isolated or canned in a metal casing in which the air adjacent to the interface has been evacuated and the interfacial area has been sealed before the application of pressure and temperature. 6 figs.

  5. Turbine blade and non-integral platform with pin attachment

    SciTech Connect (OSTI)

    Campbell, Christian X; Eng, Darryl; Marra, John J

    2015-01-27

    Platforms (36, 38) span between turbine blades (23, 24, 25) on a disk (32). Each platform may be individually mounted to the disk by a pin attachment (42). Each platform (36) may have a rotationally rearward edge portion (50) that underlies a forward portion (45) of the adjacent platform (38). This limits centrifugal bending of the rearward portion of the platform, and provides coolant sealing. The rotationally forward edge (44A, 44B) of the platform overlies a seal element (51) on the pressure side (28) of the forwardly adjacent blade, and does not underlie a shelf on that blade. The pin attachment allows radial mounting of each platform onto the disk via tilting (60) of the platform during mounting to provide mounting clearance for the rotationally rearward edge portion (50). This facilitates quick platform replacement without blade removal.

  6. Turbine blade and non-integral platform with pin attachment

    DOE Patents [OSTI]

    Campbell, Christian Xavier; Eng, Darryl; Marra, John J.

    2016-08-02

    Platforms (36, 38) span between turbine blades (23, 24, 25) on a disk (32). Each platform may be individually mounted to the disk by a pin attachment (42). Each platform (36) may have a rotationally rearward edge portion (50) that underlies a forward portion (45) of the adjacent platform (38). This limits centrifugal bending of the rearward portion of the platform, and provides coolant sealing. The rotationally forward edge (44A, 44B) of the platform overlies a seal element (51) on the pressure side (28) of the forwardly adjacent blade, and does not underlie a shelf on that blade. The pin attachment allows radial mounting of each platform onto the disk via tilting (60) of the platform during mounting to provide mounting clearance for the rotationally rearward edge portion (50). This facilitates quick platform replacement without blade removal.

  7. Pin and roller attachment system for ceramic blades

    DOE Patents [OSTI]

    Shaffer, J.E.

    1995-07-25

    In a turbine, a plurality of blades are attached to a turbine wheel by way of a plurality of joints which form a rolling contact between the blades and the turbine wheel. Each joint includes a pin and a pair of rollers to provide rolling contact between the pin and an adjacent pair of blades. Because of this rolling contact, high stress scuffing between the blades and the turbine wheel reduced, thereby inhibiting catastrophic failure of the blade joints. 3 figs.

  8. Pin and roller attachment system for ceramic blades

    DOE Patents [OSTI]

    Shaffer, James E. (Maitland, FL)

    1995-01-01

    In a turbine, a plurality of blades are attached to a turbine wheel by way of a plurality of joints which form a rolling contact between the blades and the turbine wheel. Each joint includes a pin and a pair of rollers to provide rolling contact between the pin and an adjacent pair of blades. Because of this rolling contact, high stress scuffing between the blades and the turbine wheel reduced, thereby inhibiting catastrophic failure of the blade joints.

  9. Expert Meeting Report: Cladding Attachment Over Exterior Insulation

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Cladding Attachment Over Exterior Insulation P. Baker Building Science Corporation October 2013 NOTICE This report was prepared as an account of work sponsored by an agency of the United States government. Neither the United States government nor any agency thereof, nor any of their employees, subcontractors, or affiliated partners makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus,

  10. SEC L_Attach G_Key Personnel Cost Sheet

    National Nuclear Security Administration (NNSA)

    L, Attachment G - Management Team Cost Sheet Definitions of items to be included in the worksheet Name Title Key Personnel (Y/N) Reimbursable Annual Base Salary Reimbursable Incentive Pay and bonuses Reimbursable Deferred compensation Reimbursable Employer contributions to Employee Stock Ownership Plans (ESOPs) Reimbursable Employer Contributions to Defined Contribution Pension Plans Current Annual Base Salary Current Total Annual Compensation An ESOP is a stock bonus plan designed to invest

  11. PART III … LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS

    National Nuclear Security Administration (NNSA)

    Page 130 PART III - LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS SECTION J LIST OF APPENDICES - TABLE OF CONTENTS Appendix A Statement of Work Appendix B Award Fee Plan Appendix C Transition Plan Appendix D Sensitive Foreign Nations Control Appendix E Performance Guarantee Agreement(s) Appendix F List of Applicable Directives Appendix G Personnel Appendix Appendix H Key Personnel Appendix I Small Business Subcontracting Plan Appendix J Diversity Plan Guidance Appendix K Program Management

  12. SECTION L … ATTACHMENT A - PERFORMANCE GUARANTEE AGREEMENT

    National Nuclear Security Administration (NNSA)

    A, Page 1 SECTION L ATTACHMENT A PERFORMANCE GUARANTEE AGREEMENT For value received, and in consideration of, and in order to induce the United States (the Government) to enter into Contract [insert Contract number] for the management and operation of the Nevada National Security Site (the "Contract") dated _______________, by and between the Government and _______________ (Contractor), the undersigned, ____________________ _______________ (Guarantor), a corporation incorporated in the

  13. River Corridor Closure Contract Section J, Attachment J-14

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 Contract No. DE-AC06-08RL14655 A099 1 SECTION J, ATTACHMENT J-14 ACRONYM LIST The following acronyms are used in this Contract: AB Authorization Basis ACO Administrative Contracting Officer ACWP Actual Cost of Work Performed ADR Alternative Dispute Resolution ARRA American Recovery and Reinvestment Act B&R Budgeting and Reporting BCWP Budgeted Cost of Work Performed BCWS Budgeted Cost of Work Scheduled BHI Bechtel Hanford, Inc. BMS Business Management System BRC Budget and Reporting

  14. DE-SOL-0008449 Attachment L-7c

    National Nuclear Security Administration (NNSA)

    DE-SOL-0008449 Attachment L-7c [Type here] VIETNAM MOBILIZATION PLAN DE-SOL-0008449 1.0 INTRODUCTION Based on the information presented below, the Statement of Work requirements relating to in- country deployments, and the Work Breakdown Structure (WBS) provided in Table 1, the Offeror shall develop a mobilization plan that describes its approach to a comprehensive Nuclear Smuggling Detection and Deterrence (NSDD) deployment involving Port of Cat Lai seaport in Vietnam. 2.0 REQUIREMENTS The

  15. Microsoft Word - Attachment 1 DICCE2 Statement of Work

    National Nuclear Security Administration (NNSA)

    Attachment 1 DE-SOL-0008449 1. OBJECTIVE The objective of this procurement is to install integrated sustainable radiation detection equipment at selected international land border crossings, airports, feeder ports and seaports in cooperation with international partners around the world in order to strengthen the overall capability of partner countries to deter, detect, and interdict illicit trafficking in special nuclear and other radiological materials. The focus is on the integration

  16. Removable, hermetically-sealing, filter attachment system for hostile environments

    DOE Patents [OSTI]

    Mayfield, Glenn L [Richland, WA

    1983-01-01

    A removable and reusable filter attachment system. A filter medium is fixed o, and surrounded by, a filter frame having a coaxial, longitudinally extending, annular rim. The rim engages an annular groove which surrounds the opening of a filter housing. The annular groove contains a fusible material and a heating mechanism for melting the fusible material. Upon resolidifying, the fusible material forms a hermetic bond with the rim and groove. Remelting allows detachment and replacement of the filter frame.

  17. Attachment J-16 Portfolio Management Task Order 14-001

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mod 323 Attachment J-16 Portfolio Management Task Order 14-001 Statement of Work - 1 - Title: AMRP PBS 41 - Project Management / Project Controls Support Revision Number: 0 Date: September 17, 2013 Start: October 1, 2013 Finish: September 30, 2014 1.0 DESCRIPTION Mission Support Alliance (MSA) Portfolio Management (PFM) will provide the following project management/project controls support services as described below. The services will be performed in accordance with Contract DE-AC06-09RL14728,

  18. Microsoft Word - Attachment B - Reporting Requirements.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DE-SOL-0003339 J.1 ATTACHMENT B - REPORTING REQUIREMENTS REPORTING REQUIREMENTS CHECKLIST 1. AWARDEE: 2. IDENTIFICATION NUMBER: REPORT SUBMISSION: Reports shall be submitted to the electronic addresses indicated in the NETL-identified distribution list provided in the post award debriefing. Electronic copies of each report must be submitted to the Contract Specialist (CS) and Contracting Officer's Representative (COR). 4. PLANNING AND REPORTING REQUIREMENTS FORM NO. FREQ. NO. OF COPIES FORM NO.

  19. Attached is Policy Flash 2013-34 Department of Energy Acquisition...

    Broader source: Energy.gov (indexed) [DOE]

    Attached is Policy Flash 2013-34 Department of Energy Acquisition Letter 2013-04 on Executive Compensation The information attached to this policy flash may be superseded at a...

  20. PolFlash10-31_attach1.pdf | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    PolFlash10-31attach1.pdf More Documents & Publications PolFlash10-31.pdf PolFlash10-31attach2.pdf Initial Application for FAC-C, Purchasing, Financial Assistance and Property...

  1. Microsoft Word - ARRAGuideAttachment10v1.doc | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ARRAGuideAttachment10v1.doc Microsoft Word - ARRAGuideAttachment10v1.doc More Documents & Publications Microsoft Word - ARRAAttachment12v1.doc Microsoft Word - DRAFT CRB Interview Guidance

  2. EECBG 10-07C/SEP 10-006B Attachment 1: Process Metrics List |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy 10-07C/SEP 10-006B Attachment 1: Process Metrics List EECBG 10-07C/SEP 10-006B Attachment 1: Process Metrics List eecbg_sep_reporting_guidance_attachment_06242011.pdf (56.65 KB) More Documents & Publications EECBG SEP Attachment 1 - Process metric list EECBG Program Notice 10-07A DOE Recovery Act Reporting Requirements for the State Energy Program

  3. Attachment A: Modeling in Support of Additional Two-Unit Operating

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Configurations | Department of Energy Attachment A: Modeling in Support of Additional Two-Unit Operating Configurations Attachment A: Modeling in Support of Additional Two-Unit Operating Configurations Docket No. EO-05-01: Attachment to the Operating Plan of Mirant Potomac River, LLC Attachment A: Modeling in Support of Additional Two-Unit Operating Configurations (28.18 KB) More Documents & Publications Mirant Potomac, Alexandria, Virginia: Maximum Impacts Predicted by AERMOD-PRIME

  4. Post-Installation Report Outline (IDIQ Attachment J-9) | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Installation Report Outline (IDIQ Attachment J-9) Post-Installation Report Outline (IDIQ Attachment J-9) Document offers a post-installation report outline sample for an energy savings performance contract. Download the post-installation report outline document. (56.26 KB) More Documents & Publications Measurement and Verification Plan and Savings Calculations Methods Outline (IDIQ Attachment J-8) Annual Report Outline (IDIQ Attachment J-10) ESPC Task Order Financial Schedules

  5. AttachmentFlash_2010-22(1).pdf | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    22(1).pdf AttachmentFlash2010-22(1).pdf PDF icon AttachmentFlash2010-22(1).pdf More Documents & Publications Policy Flash 2016-10 fac2001-27.pdf AttachmentFlash2010-55.pdf...

  6. River Corridor Closure Contract Section J, Attachment J-10

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    0 Contract No. DE-AC06-05RL14655 A000 1 SECTION J, ATTACHMENT J-10 RCC SUBCONTRACTS EXISTING AT TIME OF SOLICITATION The following subcontracts are/were available for assignment to the Contractor at the time Solicitation No. DE-RP06-04RL14655 was issued: End Date Current Value Description Supplier 02/28/05 $ 5,994,091 100 B/C AREA PIPELINES RCI ENVIRONMENTAL, INC. 10/31/06 $ 1,324,615 100-BC BURIAL GROUNDS AND REMAINING SITES FEDERAL ENGINEERS & CONSTRUCTORS 12/31/05 $ 3,400,000 116-N-1 CRIB

  7. River Corridor Closure Contract Section J, Attachment J-11

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1 Contract No. DE-AC06-05RL14655 Modification 398 1 SECTION J, ATTACHMENT J-11 RCC FUNDING PROFILE In accordance with the Section B clause entitled Changes to Target Cost, Target Fee, and Schedule, the following is the projected funding profile for this Contract: Fiscal Year Annual Budget Authority ($1M)* Cumulative Budget Authority ($1M)* 2005** $ 107** $ 107 2006 183 290 2007 212 502 2008 232 734 2009 242 976 2010 297 1,273 2011 376 1,649 2012 302 1,951 2013 300 2,251 2014 280 2,531 2015 201

  8. River Corridor Closure Contract Section J, Attachment J-4

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 Contract No. DE-AC06-05RL14655 A000 SECTION J, ATTACHMENT J-4 SMALL BUSINESS SUBCONTRACTING PLAN The Washington Closure LLC Small Business Subcontracting Plan is on file at the Richland Operations Office and will be available at www.hanford.gov/rl The Washington Smalll Business Subcontracting Goals are as follows (as a percent of total subcontracting effort): Small Business (SB): 65.0% Small Disadvantaged Business: 22.0% Women-Owned SB: 13.0% HUBZone SB: 4.5% Veteran-Owned SB: 3.0%

  9. River Corridor Closure Contract Section J, Attachment J-5

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 Contract No. DE-AC06-05RL14655 A000 1 SECTION J, ATTACHMENT J-5 SMALL DISADVANTAGED BUSINESS PARTICIPATION PROGRAM TARGETS (A) Washington Closure NAICS Code Description of NAICS Major Group SDB Dollars Percentage** Subtotal (B) Subcontractors NAICS Code Description of NAICS Major Group SDB Dollars Percentage** 238 Specialty Trade Contractors 37,352,000 1.92 423 Merchant Wholesalers, Durable Goods* 43,104,000 2.21 541 Professional, scientific, & tech srvcs* 13,931,000 0.72 562 Waste mgt

  10. River Corridor Closure Contract Section J, Attachment J-15

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 Contract No. DE-AC06-08RL14655 Modification 214 1 ATTACHMENT J-15 STANDARDIZED TRAINING AND COMMON SAFETY PROCESSES Document No. Worker Safety Requirement Procedure Status WCH Participation Authorized DOE-0336, Rev. 1 Hanford Site Lockout-Tagout Procedure [as required by 29 CFR 1910.147, CRD O 5480.19 (Chg. 2 Chapter IX and Rev.3), Conduct of Operations Requirements for DOE Facilities] Completed Rev. 1 (Reference MSA- 1002489, 9/2/10) Approved by DOE-RL on 11/10/10 (Reference 11-OOD- 0007) Yes