Powered by Deep Web Technologies
Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Crude oil supply curves  

E-Print Network [OSTI]

Short-run cost curves shift over time as depletion counters increasing knowledge. Under competition, a rightward (leftward) shift indicates lower (higher) cost and greater (lesser) productivity. A simple coefficient captures ...

Adelman, Morris Albert

1998-01-01T23:59:59.000Z

2

Updated U.S. Geothermal Supply Curve  

SciTech Connect (OSTI)

This paper documents the approach used to update the U.S. geothermal supply curve. The analysis undertaken in this study estimates the supply of electricity generation potential from geothermal resources in the United States and the levelized cost of electricity (LCOE), capital costs, and operating and maintenance costs associated with developing these geothermal resources. Supply curves were developed for four categories of geothermal resources: identified hydrothermal (6.4 GWe), undiscovered hydrothermal (30.0 GWe), near-hydrothermal field enhanced geothermal systems (EGS) (7.0 GWe) and deep EGS (15,900 GWe). Two cases were considered: a base case and a target case. Supply curves were generated for each of the four geothermal resource categories for both cases. For both cases, hydrothermal resources dominate the lower cost range of the combined geothermal supply curve. The supply curves indicate that the reservoir performance improvements assumed in the target case could significantly lower EGS costs and greatly increase EGS deployment over the base case.

Augustine, C.; Young, K. R.; Anderson, A.

2010-02-01T23:59:59.000Z

3

ABSTRACT: Bioenergy Harvesting Technologies to Supply Crop Residues...  

Energy Savers [EERE]

ABSTRACT: Bioenergy Harvesting Technologies to Supply Crop Residues In a Densified Large Square Bale Format ABSTRACT: Bioenergy Harvesting Technologies to Supply Crop Residues In a...

4

THE ECONOMICS OF CONSERVED-ENERGY "SUPPLY" CURVES  

E-Print Network [OSTI]

PWP-028 THE ECONOMICS OF CONSERVED-ENERGY "SUPPLY" CURVES Steven Stoft April 1995 This paper Berkeley, California 94720-5180 www.ucei.berkeley.edu/ucei #12;PWP-028 THE ECONOMICS OF CONSERVED-ENERGY "SUPPLY" CURVES Steven Stoft April 1995 #12;Table of Contents The Economics of Conserved-Energy "Supply

California at Berkeley. University of

5

Improved climate forecast accuracy: implications for the aggregate sorghum supply curve  

E-Print Network [OSTI]

for 19 sites, one in Australia (Jondaryan) and 18 in Texas, with and without SO information for five prices and three SO events. From these site yields expected aggregate supply curves weighted by hectares for Texas and Jondaryan are developed. Aggregated...

Hill, Harvey S. J.

2012-06-07T23:59:59.000Z

6

Supply Assessment of Forest Logging Residues and Non-Sawlog Biomass in the Vicinity of Missoula, Montana, 2011-2013  

E-Print Network [OSTI]

1 Supply Assessment of Forest Logging Residues and Non-Sawlog Biomass in the Vicinity of Missoula logging slash and non-sawlog biomass are commonly disposed of in the forest through piling and open biomass sources such as forest inventories, planned projects on other landownerships, and mill residues

Vonessen, Nikolaus

7

Wind Supply Curves and Location Scenarios in the West: Summary of the Clean and Diverse Energy Wind Task Force Report; Preprint  

SciTech Connect (OSTI)

This paper presents supply curves and scenarios that were developed by the Wind Task Force. Much of this information has been adapted from the original Wind Task Force report.

Milligan, M.; Parsons, B.; Shimshak, R.; Larson, D.; Carr, T.

2006-06-01T23:59:59.000Z

8

The Present, Mid-Term, and Long-Term Supply Curves for Tellurium; and Updates in the Results from NREL's CdTe PV Module Manufacturing Cost Model (Presentation)  

SciTech Connect (OSTI)

For those PV technologies that rely upon Te, In, and Ga, first-order observations and calculations hint that there may be resource constraints that could inhibit their successful deployment at a SunShot level. These are only first-order approximations, however, and the possibility for an expansion in global Te, In, and Ga supplies needs to be considered in the event that there are upward revisions in their demand and prices.In this study, we examine the current, mid-term, and long-term prospects of Tellurium (Te) for use in PV. We find that the current global supply base of Te would support <10 GW of annual traditional CdTe PV manufacturing production. But as for the possibility that the supply base for Te might be expanded, after compiling several preliminary cumulative availability curves we find that there may be significant upside potential in the supply base for this element - principally vis a vis increasing demand and higher prices. Primarily by reducing the Tellurium intensity in manufacturing and by increasing the recovery efficiency of Te in Cu refining processes, we calculate that it may prove affordable to PV manufacturers to expand the supply base for Te such that 100 GW, or greater, of annual CdTe PV production is possible in the 2030 - 2050 timeframe.

Woodhouse, M.; Goodrich, A.; Redlinger, M.; Lokanc, M.; Eggert, R.

2013-09-01T23:59:59.000Z

9

Conservation Screening Curves to Compare Efficiency Investments to Power Plants  

E-Print Network [OSTI]

methodology to compare supply and demand-side resources. The screening curve approach supplements with load curve approach supplements with load shape information the data contained in a supply curve of conservedLBL-27286 Conservation Screening Curves to Compare Efficiency Investments to Power Plants Jonathan

10

GIS Method for Developing Wind Supply Curves  

SciTech Connect (OSTI)

This report describes work conducted by the National Renewable Energy Laboratory (NREL) as part of the Wind Technology Partnership (WTP) sponsored by the U.S. Environmental Protection Agency (EPA). This project has developed methods that the National Development and Reform Commission (NDRC) intends to use in the planning and development of China's 30 GW of planned capacity. Because of China's influence within the community of developing countries, the methods and the approaches here may help foster wind development in other countries.

Kline, D.; Heimiller, D.; Cowlin, S.

2008-06-01T23:59:59.000Z

11

Petroleum Supply Monthly, September 1984  

SciTech Connect (OSTI)

This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for September 1984. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. The focus article discusses EIA data series for crude oil imports, motor gasoline supplied, and distillate and residual fuel oil supplied, as well as crude oil production. A companion article, An Evaluation of Crude Oil Production Statistics beginning on page xvii compares crude oil production volumes reported in EIA's petroleum supply publications with those shown in state reports.

Not Available

1984-11-01T23:59:59.000Z

12

Learning Curve  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

It is a fundamental human characteristic that a person engaged in a repetitive task will improve his performance over time. If data are gathered on this phenomenon, a curve representing a decrease in effort per unit for repetitive operations can be developed. This phenomenon is real and has a specific application in cost analysis, cost estimating, or profitability studies related to the examination of future costs and confidence levels in an analysis. This chapter discusses the development and application of the learning curve.

1997-03-28T23:59:59.000Z

13

Flow Duration Curve Load Duration Curve  

E-Print Network [OSTI]

#12;Flow Duration Curve Load Duration Curve #12;1. Develop Flow Duration Curve 2. Estimate load given flow and concentration data--select appropriate conversion factors 3. Develop Load Duration Curve 4. Plot observed data with Load Duration Curve #12;What are they? How do you make one? #12;Describes

14

Flow Duration Curve Load Duration Curve  

E-Print Network [OSTI]

Flow Duration Curve Load Duration Curve 1. Develop Flow Duration Curve 2. Estimate load given flow and concentration data--select appropriate conversion factors 3. Develop Load Duration Curve 4. Plot observed data with Load Duration Curve What are they? How do you make one? Describes the percent of time a flow rate

15

Power supply  

DOE Patents [OSTI]

A modular, low weight impedance dropping power supply with battery backup is disclosed that can be connected to a high voltage AC source and provide electrical power at a lower voltage. The design can be scaled over a wide range of input voltages and over a wide range of output voltages and delivered power.

Yakymyshyn, Christopher Paul (Seminole, FL); Hamilton, Pamela Jane (Seminole, FL); Brubaker, Michael Allen (Loveland, CO)

2007-12-04T23:59:59.000Z

16

Petroleum Supply Monthly, March 1985  

SciTech Connect (OSTI)

This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for March 1985. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. 13 figs., 33 tabs.

Not Available

1985-05-01T23:59:59.000Z

17

Petroleum Supply Monthly, April 1985  

SciTech Connect (OSTI)

This report contains detailed statistics on the supply and disposition of petroleum and petroleum products through April, 1985. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks.

Not Available

1985-06-01T23:59:59.000Z

18

Petroleum Supply Monthly, October 1984  

SciTech Connect (OSTI)

This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for October 1984. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administraction for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks.

Not Available

1984-12-01T23:59:59.000Z

19

Fusion Residues  

E-Print Network [OSTI]

We discuss when and how the Verlinde dimensions of a rational conformal field theory can be expressed as correlation functions in a topological LG theory. It is seen that a necessary condition is that the RCFT fusion rules must exhibit an extra symmetry. We consider two particular perturbations of the Grassmannian superpotentials. The topological LG residues in one perturbation, introduced by Gepner, are shown to be a twisted version of the $SU(N)_k$ Verlinde dimensions. The residues in the other perturbation are the twisted Verlinde dimensions of another RCFT; these topological LG correlation functions are conjectured to be the correlation functions of the corresponding Grassmannian topological sigma model with a coupling in the action to instanton number.

Kenneth Intriligator

1991-08-19T23:59:59.000Z

20

Looking Back with Interest (Rates): Merger Retrospectives in the U.S. Banking Industry  

E-Print Network [OSTI]

through Estimation of Residual Deposit Supply Equations."residual supply curves to test whether various types of deposit

Palmer, Joshua Lee

2011-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Why Supply Chain  

E-Print Network [OSTI]

Why supply chain explains the importance of supply chains. It includes an introduction to ERP as designed by SAP.

Datta, Shoumen

2000-01-01T23:59:59.000Z

22

Petroleum Supply Monthly, May 1985  

SciTech Connect (OSTI)

This report contains detailed statistics on the supply and disposition of petroleum and petroleum products through May, 1985. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. This issue features a ''Mid-Year Petroleum Review'', beginning on page xiii and focusing on major petroleum supply developments in the first half of 1985 and the outlook for the remainder of the year. The article discusses changes in consumption, domestic crude oil production, refinery operations, foreign trade, stocks (including the Strategic Petroleum Reserve) and prices. 33 tabs.

Not Available

1985-07-01T23:59:59.000Z

23

Petroleum supply monthly, July 1984  

SciTech Connect (OSTI)

This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for July 1984. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. This issue also presents IEA's winter 1984-1985 distillate fuel outlook and an overview of distillate fuel oil. These articles focus on the respective roles of production, imports, and stocks in meeting distillage fuel oil demand. Regional supply patterns, especially for the East Coast are also discussed. 33 tables. (DMC)

Not Available

1984-09-01T23:59:59.000Z

24

Determine metrics and set targets for soil quality on agriculture residue and energy crop pathways  

SciTech Connect (OSTI)

There are three objectives for this project: 1) support OBP in meeting MYPP stated performance goals for the Sustainability Platform, 2) develop integrated feedstock production system designs that increase total productivity of the land, decrease delivered feedstock cost to the conversion facilities, and increase environmental performance of the production system, and 3) deliver to the bioenergy community robust datasets and flexible analysis tools for establishing sustainable and viable use of agricultural residues and dedicated energy crops. The key project outcome to date has been the development and deployment of a sustainable agricultural residue removal decision support framework. The modeling framework has been used to produce a revised national assessment of sustainable residue removal potential. The national assessment datasets are being used to update national resource assessment supply curves using POLYSIS. The residue removal modeling framework has also been enhanced to support high fidelity sub-field scale sustainable removal analyses. The framework has been deployed through a web application and a mobile application. The mobile application is being used extensively in the field with industry, research, and USDA NRCS partners to support and validate sustainable residue removal decisions. The results detailed in this report have set targets for increasing soil sustainability by focusing on primary soil quality indicators (total organic carbon and erosion) in two agricultural residue management pathways and a dedicated energy crop pathway. The two residue pathway targets were set to, 1) increase residue removal by 50% while maintaining soil quality, and 2) increase soil quality by 5% as measured by Soil Management Assessment Framework indicators. The energy crop pathway was set to increase soil quality by 10% using these same indicators. To demonstrate the feasibility and impact of each of these targets, seven case studies spanning the US are presented. The analysis has shown that the feedstock production systems are capable of simultaneously increasing productivity and soil sustainability.

Ian Bonner; David Muth

2013-09-01T23:59:59.000Z

25

Petroleum Supply Monthly, November 1984  

SciTech Connect (OSTI)

This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for November 1984. Information on crude oil, gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Summary statistics include data from 1973 to 1984. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude oil, net receipts, crude losses, refinery inputs, exports, products supplied,and ending stocks. The focus article, US Petroleum Developments - - 1984., summarizes changes in consumption, refinery operations, petroleum stocks, imports, production and prices. The article includes an update on refinery closings.

Not Available

1985-01-28T23:59:59.000Z

26

Petroleum Supply Monthly, January 1985  

SciTech Connect (OSTI)

This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for January, 1985. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. This month's issue features Trends in Petroleum Product Consumption. This article describes the changing patterns of US petroleum product consumption in recent years, for the major projects and by end-use sectors.

Not Available

1985-03-01T23:59:59.000Z

27

Petroleum Supply Monthly, December 1984  

SciTech Connect (OSTI)

This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for December 1984. Information on crude oil, gasoline, distillate fuel oil, residual fuel oil, and liquefied petroleum gases are included. Summary statistics include data from 1973 through January 1985. Detailed statistics show production for the current month as well as the year-to-date. Data are also tubulated for the US Petroleum Administration for Defense (PAD) District which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude oil, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. The featured article, US Petroleum Import/Export Trends, highlights 1984 activities and discusses historical US trade patterns for crude oil and petroleum products. 12 figures, 33 tables.

Not Available

1985-02-01T23:59:59.000Z

28

1992 Conversion Resources Supply Document  

SciTech Connect (OSTI)

In recent years conservation of electric power has become an integral part of utility planning. The 1980 Pacific Northwest Electric Power Planning and Conservation Act (Northwest Power Act) requires that the region consider conservation potential in planning acquisitions of resources to meet load growth. The Bonneville Power Administration (BPA) developed its first estimates of conservation potential in 1982. Since that time BPA has updated its conservation supply analyses as a part of its Resource Program and other planning efforts. Major updates were published in 1985 and in January 1990. This 1992 document presents updated supply curves, which are estimates of the savings potential over time (cumulative savings) at different cost levels of energy conservation measures (ECMs). ECMs are devices, pieces of equipment, or actions that increase the efficiency of electricity use and reduce the amount of electricity used by end-use equipment.

Not Available

1992-03-01T23:59:59.000Z

29

2009 Geothermal, Co-Production, and GSHP Supply Curves  

Broader source: Energy.gov (indexed) [DOE]

- Enhanced Geothermal Systems (EGS) (update) - Co-Produced Fluids (new) - Ground Source Heat Pumps (GSHP) (new) Overview 3 | US DOE Geothermal Program eere.energy.gov HydroEGS...

30

Cost Curves for Gas Supply Security: The Case of Bulgaria  

E-Print Network [OSTI]

. Interconnections: 8.64 7.92 14 - 5 Figure 2. Structure of gas consumption by sector, Bulgaria (2007) Figure 3. Structure of heat generation by fuel type, Bulgaria (2007) Figure 4. Electricity generation mix, Bulgaria (2007) Chemical industry 31... to put the vertical dotted line). The government may want to insure the gas consumption of some specific categories of customers, the interruption of which Cost per unit of peak gas consumption insured (m€/mcm/day) Cumulative level of peak gas...

Silve, Florent; Noël, Pierre

31

Selected GHG Emission Supply Curves | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of InspectorConcentrating Solar PowerstoriesNrelPartnerTypePonsa, Mallorca: EnergySecondary EnergyGHG Emission

32

Motor Systems Efficiency Supply Curves | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to:46 -Energieprojekte3 Climate ZoneMontrose,Stanley CapitalNorthMoscow isMotley

33

McKinsey Carbon Supply Curves | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to:46 - 429Lacey,(MonasterLowellisMcDonald is a borough in91. It

34

Instrumental Variables and the Search for Identification: From Supply and  

E-Print Network [OSTI]

and demand for flaxseed, the source of linseed oil.2 Wright noted the difficulty of obtaining estimatesInstrumental Variables and the Search for Identification: From Supply and Demand to Natural variables involved attempts to estimate demand and supply curves.1 Economists such as P.G. Wright, Henry

Ahmad, Sajjad

35

Introduction Literature Review Integrated Electric Power Supply Chains Empirical Examples Conclusions An Integrated Electric Power Supply Chain and Fuel  

E-Print Network [OSTI]

of fuel demands 30% of the natural gas demand (over 50% in the summer) 90% of the coal demand over 45% of the residual fuel oil demand. #12;Introduction Literature Review Integrated Electric Power Supply ChainsIntroduction Literature Review Integrated Electric Power Supply Chains Empirical Examples

Nagurney, Anna

36

Introduction Literature Review Integrated Electric Power Supply Chains Empirical Examples Conclusions An Integrated Electric Power Supply Chain and Fuel  

E-Print Network [OSTI]

% in the summer) 90% of the coal demand over 45% of the residual fuel oil demand. #12;Introduction LiteratureIntroduction Literature Review Integrated Electric Power Supply Chains Empirical Examples Conclusions An Integrated Electric Power Supply Chain and Fuel Market Network Framework: Theoretical Modeling

Nagurney, Anna

37

Supply Systems Analyst  

Broader source: Energy.gov [DOE]

In this position you will serve as a Supply Systems Analyst for Supply Chain Services. The incumbent is responsible for managing and supporting multiple electronic database systems, including Asset...

38

ABSTRACT: Bioenergy Harvesting Technologies to Supply Crop Residues In a  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustionImprovement3 Beryllium-Associated Worker2014DepartmentI325 8 (8-89) EFGDepartment ofABOUT

39

ABSTRACT: Bioenergy Harvesting Technologies to Supply Crop Residues In a  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review: Top Five EERE Blog Posts of 2014ReviewsndSIMPLEResponse to Smart GridDensified

40

An Experimental/Computational Approach to Identify Moduli and Residual Stress  

E-Print Network [OSTI]

and uniformity of measured load­deflection curves on a number of switches with both wedge and Berkovich tips has a strong effect on load­ deflection curves; hence, its accurate characterization is crit- ical stress state affect the load­deflection curve in dif- ferent regimes. Changes in residual stress state

Espinosa, Horacio D.

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Simultaneous confidence bands in curve prediction applied to load curves  

E-Print Network [OSTI]

Simultaneous confidence bands in curve prediction applied to load curves J.M. Aza¨is1, S. Bercu2, J, load curve. 1 Introduction In curve prediction, one is generally interested in deriving simultaneous this technique in the numerical context of load curve pre- diction: power producers like EDF, the electrical

Boyer, Edmond

42

Oil and Gas Supply Module  

Gasoline and Diesel Fuel Update (EIA)

Onshore Lower 48 Oil and Gas Supply Submodule, Offshore Oil and Gas Supply Submodule, Oil Shale Supply Submodule1, and Alaska Oil and Gas Supply Submodule. A detailed description...

43

Oil and Gas Supply Module  

Gasoline and Diesel Fuel Update (EIA)

Onshore Lower 48 Oil and Gas Supply Submodule, Offshore Oil and Gas Supply Submodule, Oil Shale Supply Submodule, and Alaska Oil and Gas Supply Submodule. A detailed description of...

44

NUFinancials Supply Chain  

E-Print Network [OSTI]

NUFinancials Supply Chain FMS801 & 803 Purchasing Glossary 03/31/2010 © 2010 Northwestern University FMS801 & 803 1 Purchasing Glossary Guide to terms used in iBuyNU and NUFinancials purchasing Term, faculty salary, office supplies. Similar to CUFS Object Code, Revenue Source, and Balance Sheet. Note

Shull, Kenneth R.

45

Updated U.S. Geothermal Supply Characterization and Representation for Market Penetration Model Input  

SciTech Connect (OSTI)

The U.S. Department of Energy (DOE) Geothermal Technologies Program (GTP) tasked the National Renewable Energy Laboratory (NREL) with conducting the annual geothermal supply curve update. This report documents the approach taken to identify geothermal resources, determine the electrical producing potential of these resources, and estimate the levelized cost of electricity (LCOE), capital costs, and operating and maintenance costs from these geothermal resources at present and future timeframes under various GTP funding levels. Finally, this report discusses the resulting supply curve representation and how improvements can be made to future supply curve updates.

Augustine, C.

2011-10-01T23:59:59.000Z

46

ISOMORPHISM CLASSES OF PICARD CURVES OVER FINITE FIELDS  

E-Print Network [OSTI]

for construction of cryptosystems based on the discrete logarithm problem, and elliptic curve cryptography is now for constructing public key cryptosystems by Galbraith, Paulus and Smart in [8]. Besides providing an algorithm, of a place p is defined as the extension degree of the residue field of p over k. For a divisor D = npp (that

47

The dynamics of mercury flow in a curved pipe  

E-Print Network [OSTI]

The dynamics of mercury flow in a curved pipe Yan Zhan Foluso LadeindeFoluso Ladeinde 11 of the problem Pi t ff t· Pipe curvature effect · Laminar flow in the mercury supply pipe l i· Conclusion #12 Project. · Target delivery systems involves pipe curvature, axially- d d t di l di t d l l th tdependent

McDonald, Kirk

48

Biofuels supply chain characterization  

E-Print Network [OSTI]

Ethanol can be made from agricultural residues like wheat straw and from crops dedicated to energy use, like switchgrass. We study the logistics aspects of this transformation and determine the main characteristics of the ...

Banerjee, Anindya, M. Eng. Massachusetts Institute of Technology

2007-01-01T23:59:59.000Z

49

European supply chain study  

E-Print Network [OSTI]

Introduction: Supply chain management has been defined as, "..a set of approaches utilized to efficiently integrate suppliers, manufacturers, warehouses and stores, so that merchandise is produced and distributed at the ...

Puri, Mohitkumar

2009-01-01T23:59:59.000Z

50

Improving supply chain resilience  

E-Print Network [OSTI]

Due to the global expansion of Company A's supply chain network, it is becoming more vulnerable to many disruptions. These disruptions often incur additional costs; and require time to respond to and recover from these ...

Leung, Elsa Hiu Man

2009-01-01T23:59:59.000Z

51

Extinction curves in AGN  

E-Print Network [OSTI]

The presence of the dust in the circumnuclear region strongly affects our view of the nucleus itself. The effect is strong in type 2 objects but weaker effect is likely to be present in type 1 objects as well. In these objects a correction to the observed optical/UV spectrum must be done in order to recover the intrinsic spectrum of a nucleus. The approach based on the extinction curve is convenient for that purpose so significant effort has been recently done in order to determine the extinction curve for the circumnuclear material. It seems clear that the circumnuclear dust is different from the average properties of the dust in the Interstellar Medium in our galaxy: the well known 2175 A feature is weak or absent in AGN nuclear dust, and the extinction curve at shorter wavelength does not seem to be rising as steeply. The circumnuclear dust is therefore more similar to SMC dust, or more likely, to the dust in very dense molecular clouds in our Galaxy. However, the exact shape of the extinction curve in the far UV is still a matter of debate, and various effects are difficult to disentangle.

B. Czerny

2006-12-16T23:59:59.000Z

52

Outline Introduction Literature Review Electric Power Supply Chains Empirical Examples Conclusions An Integrated Electric Power Supply Chain and Fuel Market  

E-Print Network [OSTI]

Supply Chains and Fuel Markets In the U.S., electric power generation accounts for 30% of the natural gas demand (over 50% in the summer), 90% of the coal demand, and over 45% of the residual fuel oil demand, the wholesale electricity price in New England decreased by 38% mainly because the delivered natural gas price

Nagurney, Anna

53

Outline Introduction Literature Review Electric Power Supply Chains Empirical Examples Conclusions An Integrated Electric Power Supply Chain and Fuel  

E-Print Network [OSTI]

.S., electric power generation accounts for significant portions of fuel demands 30% of the natural gas demand (over 50% in the summer) 90% of the coal demand over 45% of the residual fuel oil demand #12;OutlineOutline Introduction Literature Review Electric Power Supply Chains Empirical Examples Conclusions

Nagurney, Anna

54

Introduction Literature Review Integrated Electric Power Supply Chains Empirical Examples Conclusions An Integrated Electric Power Supply Chain and Fuel  

E-Print Network [OSTI]

50% in the summer) 90% of the coal demand over 45% of the residual fuel oil demand. #12;Introduction, the wholesale electricity price in New England decreased by 38% mainly because the delivered natural gas priceIntroduction Literature Review Integrated Electric Power Supply Chains Empirical Examples

Nagurney, Anna

55

Petroleum Supply Monthly  

SciTech Connect (OSTI)

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

NONE

1996-02-01T23:59:59.000Z

56

Petroleum supply monthly  

SciTech Connect (OSTI)

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blends, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

NONE

1995-10-01T23:59:59.000Z

57

Petroleum supply annual 1996: Volume 1  

SciTech Connect (OSTI)

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1996 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Capacity; each with final annual data. The summary statistics section show 16 years of data depicting the balance between supply, disposition and ending stocks for various commodities including crude oil, motor gasoline, distillate fuel oil, residual fuel oil, jet fuel propane/propylene, and liquefied petroleum gases. The detailed statistics section provide 1996 detailed statistics on supply and disposition, refinery operations, imports and exports, stocks, and transportation of crude oil and petroleum products. The refinery capacity contain listings of refineries and associated crude oil distillation and downstream capacities by State, as of January 1, 1997, as well as summaries of corporate refinery capacities and refinery storage capacities. In addition, refinery receipts of crude oil by method of transportation for 1996 are provided. Also included are fuels consumed at refineries, and lists of shutdowns, sales, reactivations, and mergers during 1995 and 1996. 16 figs., 59 tabs.

NONE

1997-06-01T23:59:59.000Z

58

Connecting curves for dynamical systems  

E-Print Network [OSTI]

We introduce one dimensional sets to help describe and constrain the integral curves of an $n$ dimensional dynamical system. These curves provide more information about the system than the zero-dimensional sets (fixed points) do. In fact, these curves pass through the fixed points. Connecting curves are introduced using two different but equivalent definitions, one from dynamical systems theory, the other from differential geometry. We describe how to compute these curves and illustrate their properties by showing the connecting curves for a number of dynamical systems.

R. Gilmore; Jean-Marc Ginoux; Timothy Jones; C. Letellier; U. S. Freitas

2010-03-08T23:59:59.000Z

59

Physical modeling of the soil swelling curve vs. the shrinkage curve  

E-Print Network [OSTI]

Physical understanding of the links between soil swelling, texture, structure, cracking, and sample size is of great interest for the physical understanding of many processes in the soil-air-water system and for applications in civil, agricultural, and environmental engineering. The background of this work is an available chain of interconnected physical shrinkage curve models for clay, intra-aggregate matrix, aggregated soil without cracks, and soil with cracks. The objective of the work is to generalize these models to the case of swelling, and to construct the physical-swelling-model chain with a step-by-step transition from clay to aggregated soil with cracks. The generalization is based on thorough accounting for the analogies and differences between shrinkage and swelling and the corresponding use, modification, or replacement of the soil shrinkage features. Two specific soil swelling features to be used are: (i) air entrapping in pores of the contributing clay; and (ii) aggregate destruction with the formation of new aggregate surfaces. The input for the prediction of the swelling curve of an aggregated soil coincides with that of the available model of the shrinkage curve. The analysis of available data on the maximum shrink-swell cycle of two soils with different texture and structure, accounting for sample size is conducted as applied to swelling curves and to the residual crack volume and maximum-swelling-volume decrease after the shrink-swell cycle. Results of the analysis show evidence in favor of the swelling model chain.

V. Y. Chertkov

2014-04-14T23:59:59.000Z

60

Petroleum supply monthly, February 1988. [Contains glossary  

SciTech Connect (OSTI)

Total US demand for petroleum products during February 1988 averaged about 17.6 million barrels per day, 0.9 million barrels per day above the average of a year earlier. This marks the third consecutive month in which total product supplied has exceeded 17.0 million barrels per day. For the most part, the disposition of the major products continued to follow seasonal patterns. Total products stocks dropped by 26.0 million barrels to 683.1 million barrels. Refinery utilization fell from January's 82.8 percent rate to 81.1 percent. Crude oil imports from Saudi Arabia rose to 1.2 million barrels per day, 0.4 million barrels per day above the average for January. Unusually mild weather, especially in the Mid-Atlantic states and New England, kept deliveries of both distillate and residual fuel oil virtually unchanged from January's high seasonal levels, although both were still well above the levels for these products the same time last year. Distillate demand averaged 3.5 million barrels per day in February, five percent above the February 1987 average. Residual fuel oil demand was 1.6 million barrels per day this month, nine percent greater than a year ago. Part of this increase in demand from the previous year reflects the improved competitive position of residual fuel oil in some utility and industrial markets, mostly due to increases in natural gas prices starting in the fourth quarter of 1987. 12 figs.

Not Available

1988-04-25T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Fiber Supply Associate Company Overview  

E-Print Network [OSTI]

materials acquisition, harvesting, logistics coordination, contract negotiations, and inventory management, Purchasing, Industrial Engineering, Operations management, Materials Management, Supply Chain) Authorized leadership roles such as Fiber Specialist, Fiber Supply Manager, Region Manager, Director, General Manager

Mazzotti, Frank

62

Services & Supplies EHP Network Provider  

E-Print Network [OSTI]

and Serum 80% 80% of R&C Ambulance Transportation Medically Necessary Transport 80% 80% of R&C Chemotherapy% 80% of R&C Medically Necessary Hearing Aids for dependent children up to age 26 (limited to every 36, and Ultrasound 90% 70% of R&C Medical Supplies Disposable Supplies (e.g. ostomy bags, diabetic supplies, syringes

Niebur, Ernst

63

GLOBAL WOOD SUPPLY Sten Nilsson  

E-Print Network [OSTI]

GLOBAL WOOD SUPPLY Sten Nilsson Biomass and Resource Efficiency: the need for a supply led approach to forest productivity European Parliament, Brussels, 10 November 2011 #12;MEGATREND WOOD SUPPLY ­ 2020 the trees on the right Source: JP Management Consulting (Asia-Pacific) Ltd., 2006 #12;BAMBOO FOREST Source

64

Langevin Equation on Fractal Curves  

E-Print Network [OSTI]

We analyse a random motion of a particle on a fractal curve, using Langevin approach. This involves defining a new velocity in terms of mass of the fractal curve, as defined in recent work. The geometry of the fractal curve, hence plays an important role in this analysis. A Langevin equation with a particular noise model is thus proposed and solved using techniques of the newly developed $F^\\alpha$-Calculus .

Seema Satin; A. D. Gangal

2014-04-28T23:59:59.000Z

65

GSA Wind Supply Opportunity  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeatMulti-Dimensional Subject: Guidance for natural gas asWind Supply Opportunity 1 2 3

66

Self Supplied Balancing Reserves  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas ConchasPassiveSubmitted forHighlights NuclearSelf-Supplied-Balancing-Reserves Sign In About |

67

CSC6870 Computer Graphics II Bezier Curves  

E-Print Network [OSTI]

CSC6870 Computer Graphics II Bezier Curves CSC6870 Computer Graphics II Bezier Curve CSC6870 Computer Graphics II Cubic Bezier Curves · Curve: · Control points · Basis functions: = = 3 0 3 )()( i ii uBpuc ip CSC6870 Computer Graphics II Bezier Curves (degree n) · Curve: · Control points · Basis functions

Hua, Jing

68

Random Curves by Conformal Welding  

E-Print Network [OSTI]

We construct a conformally invariant random family of closed curves in the plane by welding of random homeomorphisms of the unit circle given in terms of the exponential of Gaussian Free Field. We conjecture that our curves are locally related to SLE$(\\kappa)$ for $\\kappa<4$.

Astala, K; Kupiainen, A; Saksman, E

2009-01-01T23:59:59.000Z

69

Random Curves by Conformal Welding  

E-Print Network [OSTI]

We construct a conformally invariant random family of closed curves in the plane by welding of random homeomorphisms of the unit circle given in terms of the exponential of Gaussian Free Field. We conjecture that our curves are locally related to SLE$(\\kappa)$ for $\\kappa<4$.

K. Astala; P. Jones; A. Kupiainen; E. Saksman

2009-12-17T23:59:59.000Z

70

SRC Residual fuel oils  

DOE Patents [OSTI]

Coal solids (SRC) and distillate oils are combined to afford single-phase blends of residual oils which have utility as fuel oils substitutes. The components are combined on the basis of their respective polarities, that is, on the basis of their heteroatom content, to assure complete solubilization of SRC. The resulting composition is a fuel oil blend which retains its stability and homogeneity over the long term.

Tewari, Krishna C. (Whitehall, PA); Foster, Edward P. (Macungie, PA)

1985-01-01T23:59:59.000Z

71

NNSA TRITIUM SUPPLY CHAIN  

SciTech Connect (OSTI)

Savannah River Site plays a critical role in the Tritium Production Supply Chain for the National Nuclear Security Administration (NNSA). The entire process includes: • Production of Tritium Producing Burnable Absorber Rods (TPBARs) at the Westinghouse WesDyne Nuclear Fuels Plant in Columbia, South Carolina • Production of unobligated Low Enriched Uranium (LEU) at the United States Enrichment Corporation (USEC) in Portsmouth, Ohio • Irradiation of TPBARs with the LEU at the Tennessee Valley Authority (TVA) Watts Bar Reactor • Extraction of tritium from the irradiated TPBARs at the Tritium Extraction Facility (TEF) at Savannah River Site • Processing the tritium at the Savannah River Site, which includes removal of nonhydrogen species and separation of the hydrogen isotopes of protium, deuterium and tritium.

Wyrick, Steven [Savannah River National Laboratory, Aiken, SC, USA; Cordaro, Joseph [Savannah River National Laboratory, Aiken, SC, USA; Founds, Nanette [National Nuclear Security Administration, Albuquerque, NM, USA; Chambellan, Curtis [National Nuclear Security Administration, Albuquerque, NM, USA

2013-08-21T23:59:59.000Z

72

Sustainable Biomass Supply Systems  

SciTech Connect (OSTI)

The U.S. Department of Energy (DOE) aims to displace 30% of the 2004 gasoline use (60 billion gal/yr) with biofuels by 2030 as outlined in the Energy Independence and Security Act of 2007, which will require 700 million tons of biomass to be sustainably delivered to biorefineries annually. Lignocellulosic biomass will make an important contribution towards meeting DOE’s ethanol production goals. For the biofuels industry to be an economically viable enterprise, the feedstock supply system (i.e., moving the biomass from the field to the refinery) cannot contribute more that 30% of the total cost of the biofuel production. The Idaho National Laboratory in collaboration with Oak Ridge National Laboratory, University of California, Davis and Kansas State University are developing a set of tools for identifying economical, sustainable feedstocks on a regional basis based on biorefinery siting.

Erin Searcy; Dave Muth; Erin Wilkerson; Shahab Sokansanj; Bryan Jenkins; Peter Titman; Nathan Parker; Quinn Hart; Richard Nelson

2009-04-01T23:59:59.000Z

73

Switching power supply  

DOE Patents [OSTI]

The invention is a repratable capacitor charging, switching power supply. A ferrite transformer steps up a dc input. The transformer primary is in a full bridge configuration utilizing power MOSFETs as the bridge switches. The transformer secondary is fed into a high voltage, full wave rectifier whose output is connected directly to the energy storage capacitor. The transformer is designed to provide adequate leakage inductance to limit capacitor current. The MOSFETs are switched to the variable frequency from 20 to 50 kHz to charge a capacitor from 0.6 kV. The peak current in a transformer primary and secondary is controlled by increasing the pulse width as the capacitor charges. A digital ripple counter counts pulses and after a preselected desired number is reached an up-counter is clocked.

Mihalka, A.M.

1984-06-05T23:59:59.000Z

74

Supply Chain Analysis Center for Transportation Analysis  

E-Print Network [OSTI]

Supply Chain Analysis Center for Transportation Analysis 2360 Cherahala Boulevard Knoxville, TN experience in supply chain analysis and automated support for supply chain systems. ORNL's Capabilities Optimization modeling for supply chain systems, including: Facility number and location analysis

75

Tariffs with Dynamic Supply Response  

E-Print Network [OSTI]

Giannini FDN iibrary TARIFFS WITH DYNAMIC SUPPLY RESWNSEpaper studies the optimal tariff in a dynamic framework. Thesellers, the optimal tariff is dynam- ically inconsistent;

Karp, Larry

1985-01-01T23:59:59.000Z

76

Industry Supply Chain Development (Ohio)  

Broader source: Energy.gov [DOE]

Supply Chain Development programs are focused on targeted industries that have significant growth opportunities for Ohio's existing manufacturing sector from emerging energy resources and...

77

Repetitive resonant railgun power supply  

DOE Patents [OSTI]

A repetitive resonant railgun power supply provides energy for repetitively propelling projectiles from a pair of parallel rails. The supply comprises an energy storage capacitor, a storage inductor to form a resonant circuit with the energy storage capacitor and a magnetic switch to transfer energy between the resonant circuit and the pair of parallel rails for the propelling of projectiles.

Honig, E.M.; Nunnally, W.C.

1985-06-19T23:59:59.000Z

78

WATER SUPPLY A Handbook on  

E-Print Network [OSTI]

WATER SUPPLY HANDBOOK A Handbook on Water Supply Planning and Resource Management Institute for Water Resources Water Resources Support Center U.S. Army Corps of Engineers 7701 Telegraph Road Studies Division December 1998 Revised IWR Report 96-PS-4 #12;U.S. Army Institute for Water Resources

US Army Corps of Engineers

79

Power Supply Synchronization without Communication  

E-Print Network [OSTI]

1 Power Supply Synchronization without Communication Leonardo A. B. T^orres, Jo~ao P. Hespanha, Jeff Moehlis Abstract--We consider the synchronization of power supplies in an isolated grid with multiple small-to-medium power sources. We show how to achieve a coordinated or synchronized behavior

Moehlis, Jeff

80

Petroleum supply monthly, August 1993  

SciTech Connect (OSTI)

This publication the Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report, (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. Data presented are divided into Summary Statistics and Detailed Statistics.

Not Available

1993-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

The soil reference shrinkage curve  

E-Print Network [OSTI]

A recently proposed model showed how a clay shrinkage curve is transformed to the soil shrinkage curve at the soil clay content higher than a critical one. The objective of the present work was to generalize this model to the soil clay content lower a critical one. I investigated (i) the reference shrinkage curve, that is, one without cracks; (ii) the superficial layer of aggregates, with changed pore structure compared with the intraaggregate matrix; and (iii) soils with sufficiently low clay content where there are large pores inside the intraaggregate clay (so-called lacunar pores). The methodology is based on detail accounting for different contributions to the soil volume and water content during shrinkage. The key point is the calculation of the lacunar pore volume variance at shrinkage. The reference shrinkage curve is determined by eight physical soil parameters: (1) oven-dried specific volume; (2) maximum swelling water content; (3) mean solid density; (4) soil clay content; (5) oven-dried structural porosity; (6) the ratio of aggregate solid mass to solid mass of intraaggregate matrix; (7) the lacunar factor that characterizes the rate of the lacunar pore volume change with water content; and (8) oven-dried lacunar pore volume. The model was validated using available data. The model predicted value of the slope of the reference shrinkage curve in the basic shrinkage area is equal to unity minus the lacunar factor value, and is between unity and zero in the agreement with observations.

V. Y. Chertkov

2014-03-11T23:59:59.000Z

82

Residuals, Sludge, and Composting (Maine)  

Broader source: Energy.gov [DOE]

The Maine Department of Environmental Protection's Residuals, Sludge, and Composting program regulates the land application and post-processing of organic wastes, including sewage sludge, septage,...

83

Improve supply chain resilience by multi-stage supply chain  

E-Print Network [OSTI]

Due to the global expansion of Company A's supply chain network, it is becoming more vulnerable to many disruptions. These disruptions often incur additional costs; and require time to respond to and recover from these ...

Xu, Jie, M. Eng. Massachusetts Institute of Technology

2009-01-01T23:59:59.000Z

84

Improving supply chain resilience by multi-stage supply chain  

E-Print Network [OSTI]

Due to the global expansion of Company A's supply chain network, it is becoming more vulnerable to many disruptions. These disruptions often incur additional costs; and require time to respond to and recover from these ...

Yang, Jingxia, M. Eng, Massachusetts Institute of Technology

2009-01-01T23:59:59.000Z

85

Petroleum supply monthly, February 1994  

SciTech Connect (OSTI)

The Petroleum Supply Monthly presents data describing the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders; operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. Data are divided into two sections: Summary statistics and Detailed statistics.

Not Available

1994-03-01T23:59:59.000Z

86

Multiple resonant railgun power supply  

DOE Patents [OSTI]

A multiple repetitive resonant railgun power supply provides energy for repetitively propelling projectiles from a pair of parallel rails. A plurality of serially connected paired parallel rails are powered by similar power supplies. Each supply comprises an energy storage capacitor, a storage inductor to form a resonant circuit with the energy storage capacitor and a magnetic switch to transfer energy between the resonant circuit and the pair of parallel rails for the propelling of projectiles. The multiple serial operation permits relatively small energy components to deliver overall relatively large amounts of energy to the projectiles being propelled.

Honig, E.M.; Nunnally, W.C.

1985-06-19T23:59:59.000Z

87

Petroleum supply monthly, April 1994  

SciTech Connect (OSTI)

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographical regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US.

Not Available

1994-04-01T23:59:59.000Z

88

Effective contracts in supply chains  

E-Print Network [OSTI]

In the past decade, we have seen significant increase in the level of outsourcing in many industries. This increase in the level of outsourcing increases the importance of implementing effective contracts in supply chains. ...

Shum, Wanhang

2007-01-01T23:59:59.000Z

89

The 3He Supply Problem  

SciTech Connect (OSTI)

One of the main uses for 3He is in gas proportional counters for neutron detection. Radiation portal monitors deployed for homeland security and non-proliferation use such detectors. Other uses of 3He are for research detectors, commercial instruments, well logging detectors, dilution refrigerators, for targets or cooling in nuclear research, and for basic research in condensed matter physics. The US supply of 3He comes almost entirely from the decay of tritium used in nuclear weapons by the US and Russia. A few other countries contribute a small amount to the world’s 3He supply. Due to the large increase in use of 3He for homeland security, the supply has dwindled, and can no longer meet the demand. This white paper reviews the problems of supply, utilization, and alternatives.

Kouzes, Richard T.

2009-05-01T23:59:59.000Z

90

Total supply chain cost model  

E-Print Network [OSTI]

Sourcing and outsourcing decisions have taken on increased importance within Teradyne to improve efficiency and competitiveness. This project delivered a conceptual framework and a software tool to analyze supply chain ...

Wu, Claudia

2005-01-01T23:59:59.000Z

91

Petroleum supply monthly, April 1990  

SciTech Connect (OSTI)

The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in the Petroleum Supply Monthly describe (PSM) the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply.'' Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: (1) the Summary Statistics and (2) the Detailed Statistics.

None

1990-06-26T23:59:59.000Z

92

Supplying High-Quality, Raw Biomass  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Supplying High-Quality, Raw Biomass The building blocks to supply high-quality raw biomass start with harvesting and collection practices, product storage and recommendations of...

93

NREL: Jobs and Economic Competitiveness - Supply Constraints...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Supply Constraints Analysis Some of the materials used in solar PV modules, such as tellurium and indium, are rare materials in limited supply. Solar PV technologies have grown...

94

Environmental decision making: supply-chain considerations  

E-Print Network [OSTI]

manufacturing environmental impact and enable the reductionthe supply chain (3) environmental impact and cost must bethe supply chain’s environmental impact and flexibility (

Reich-Weiser, Corinne; Dornfeld, David

2008-01-01T23:59:59.000Z

95

Petroleum supply monthly, October 1993  

SciTech Connect (OSTI)

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Not Available

1993-10-26T23:59:59.000Z

96

Petroleum Supply Monthly, August 1990  

SciTech Connect (OSTI)

The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) district movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics.

Not Available

1990-10-30T23:59:59.000Z

97

Petroleum supply monthly, January 1996  

SciTech Connect (OSTI)

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

NONE

1996-02-15T23:59:59.000Z

98

Petroleum supply monthly, July 1994  

SciTech Connect (OSTI)

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Not Available

1994-07-26T23:59:59.000Z

99

Petroleum supply monthly, June 1994  

SciTech Connect (OSTI)

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Not Available

1994-06-28T23:59:59.000Z

100

Petroleum supply monthly, September 1991  

SciTech Connect (OSTI)

The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administrations for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics. 65 tabs.

Not Available

1991-09-30T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Optical conductivity of curved graphene  

E-Print Network [OSTI]

We compute the optical conductivity for an out-of-plane deformation in graphene using an approach based on solutions of the Dirac equation in curved space. Different examples of periodic deformations along one direction translates into an enhancement of the optical conductivity peaks in the region of the far and mid infrared frequencies for periodicities $\\sim100\\,$nm. The width and position of the peaks can be changed by dialling the parameters of the deformation profiles. The enhancement of the optical conductivity is due to intraband transitions and the translational invariance breaking in the geometrically deformed background. Furthemore, we derive an analytical solution of the Dirac equation in a curved space for a general deformation along one spatial direction. For this class of geometries, it is shown that curvature induces an extra phase in the electron wave function, which can also be explored to produce interference devices of the Aharonov-Bohm type.

A. J. Chaves; T. Frederico; O. Oliveira; W. de Paula; M. C. Santos

2014-05-01T23:59:59.000Z

102

International Oil Supplies and Demands  

SciTech Connect (OSTI)

The eleventh Energy Modeling Forum (EMF) working group met four times over the 1989--90 period to compare alternative perspectives on international oil supplies and demands through 2010 and to discuss how alternative supply and demand trends influence the world's dependence upon Middle Eastern oil. Proprietors of eleven economic models of the world oil market used their respective models to simulate a dozen scenarios using standardized assumptions. From its inception, the study was not designed to focus on the short-run impacts of disruptions on oil markets. Nor did the working group attempt to provide a forecast or just a single view of the likely future path for oil prices. The model results guided the group's thinking about many important longer-run market relationships and helped to identify differences of opinion about future oil supplies, demands, and dependence.

Not Available

1991-09-01T23:59:59.000Z

103

Petroleum supply monthly, July 1993  

SciTech Connect (OSTI)

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: Petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Not Available

1993-07-29T23:59:59.000Z

104

Petroleum supply monthly, August 1994  

SciTech Connect (OSTI)

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Not Available

1994-08-26T23:59:59.000Z

105

International Oil Supplies and Demands  

SciTech Connect (OSTI)

The eleventh Energy Modeling Forum (EMF) working group met four times over the 1989--1990 period to compare alternative perspectives on international oil supplies and demands through 2010 and to discuss how alternative supply and demand trends influence the world's dependence upon Middle Eastern oil. Proprietors of eleven economic models of the world oil market used their respective models to simulate a dozen scenarios using standardized assumptions. From its inception, the study was not designed to focus on the short-run impacts of disruptions on oil markets. Nor did the working group attempt to provide a forecast or just a single view of the likely future path for oil prices. The model results guided the group's thinking about many important longer-run market relationships and helped to identify differences of opinion about future oil supplies, demands, and dependence.

Not Available

1992-04-01T23:59:59.000Z

106

Roadmap for Agriculture Biomass Feedstock Supply in the United States  

SciTech Connect (OSTI)

The Biomass Research and Development Technical Advisory Committee established a goal that biomass will supply 5% of the nation’s power, 20% of its transportation fuels, and 25% of its chemicals by 2030. These combined goals are approximately equivalent to 30% of the country’s current petroleum consumption. The benefits of a robust biorefinery industry supplying this amount of domestically produced power, fuels, and products are considerable, including decreased demand for imported oil, revenue to the depressed agricultural industry, and revitalized rural economies. A consistent supply of highquality, low-cost feedstock is vital to achieving this goal. This biomass roadmap defines the research and development (R&D) path to supplying the feedstock needs of the biorefinery and to achieving the important national goals set for biomass. To meet these goals, the biorefinery industry must be more sustainable than the systems it will replace. Sustainability hinges on the economic profitability of all participants, on environmental impact of every step in the process, and on social impact of the product and its production. In early 2003, a series of colloquies were held to define and prioritize the R&D needs for supplying feedstock to the biorefinery in a sustainable manner. These colloquies involved participants and stakeholders in the feedstock supply chain, including growers, transporters, equipment manufacturers, and processors as well as environmental groups and others with a vested interest in ensuring the sustainability of the biorefinery. From this series of colloquies, four high-level strategic goals were set for the feedstock area: • Biomass Availability – By 2030, 1 billion dry tons of lignocellulosic feedstock is needed annually to achieve the power, fuel, and chemical production goals set by the Biomass Research and Development Technology Advisory Production Committee • Sustainability – Production and use of the 1 billion dry tons annually must be accomplished in a sustainable manner • Feedstock Infrastructure – An integrated feedstock supply system must be developed and implemented that can serve the feedstock needs of the biorefinery at the cost, quality, and consistency of the set targets • System Profitability – Economic profitability and sustainability need to be ensured for all required participants in the feedstock supply system. For each step in the biomass supply process—production, harvesting and collection, storage, preprocessing, system integration, and transportation—this roadmap addresses the current technical situations, performance targets, technical barriers, R&D needs, and R&D priorities to overcome technical barriers and achieve performance targets. Crop residue biomass is an attractive starting feedstock, which shows the best near-term promise as a biorefinery feedstock. Because crop residue is a by-product of grain production, it is an abundant, underutilized, and low cost biomass resource. Corn stover and cereal straw are the two most abundant crop residues available in the United States. Therefore, this roadmap focuses primarily on the R&D needed for using these biomass sources as viable biorefinery feedstocks. However, achieving the goal of 1 billion dry tons of lignocellulosic feedstock will require the use of other biomass sources such as dedicated energy crops. In the long term, the R&D needs identified in this roadmap will need to accommodate these other sources of biomass as well.

J. Richard Hess; Thomas D. Foust; Reed Hoskinson; David Thompson

2003-11-01T23:59:59.000Z

107

Investigating the variation in CO[subscript 2] sequestration supply curves  

E-Print Network [OSTI]

CCS projects that can bring together all pieces of the system—capture, transport, and storage—at the lowest cost will likely be the first to become operational. We have modeled the cost per tonne of CO[subscript 2] of a ...

House, Kurt Zenz

108

Sixth Northwest Conservation and Electric Power Plan Appendix E: Conservation Supply Curve  

E-Print Network [OSTI]

....................................................................................................... 11 Value of Energy Saved ......................................................................................................................... 17 Residential Sector Definition and Coverage........................................................................................................................ 22 Commercial Sector Definition and Coverage

109

2009 Geothermal, Co-Production, and GSHP Supply Curves | Department of  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-Up from theDepartment( Sample of ShipmentSimulation, Analysis

110

Estimating Carbon Supply Curves for Global Forests and Other Land Uses |  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision has beenFfe2fb55-352f-473b-a2dd-50ae8b27f0a6 NoSan Leandro,Law and PolicyEssex County is a county inOpen

111

Petroleum supply monthly, January 1994  

SciTech Connect (OSTI)

Data presented describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Not Available

1994-01-01T23:59:59.000Z

112

CALCULATING THE CARBON FOOTPRINT SUPPLY CHAIN FOR  

E-Print Network [OSTI]

CALCULATING THE CARBON FOOTPRINT SUPPLY CHAIN FOR THE SEMICONDUCTOR INDUSTRY By: Yasser Dessouky #12;Carbon Footprint Supply Chain Carbon Trust defines carbon footprint of a supply chain as follows: "The carbon footprint of a product is the carbon dioxide emitted across the supply chain for a single

Su, Xiao

113

Coupling Renewable Energy Supply with Deferrable Demand  

E-Print Network [OSTI]

systems absorb large amounts of hydroelectric power. Duringthat snow melts and hydroelectric power supply increases and

Papavasiliou, Anthony

2011-01-01T23:59:59.000Z

114

Chemical Characterization of Individual Particles and Residuals...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Individual Particles and Residuals of Cloud Droplets and Ice Crystals Collected On Board Research Chemical Characterization of Individual Particles and Residuals of Cloud Droplets...

115

DISSOLUTION OF NEPTUNIUM OXIDE RESIDUES  

SciTech Connect (OSTI)

This report describes the development of a dissolution flowsheet for neptunium (Np) oxide (NpO{sub 2}) residues (i.e., various NpO{sub 2} sources, HB-Line glovebox sweepings, and Savannah River National Laboratory (SRNL) thermogravimetric analysis samples). Samples of each type of materials proposed for processing were dissolved in a closed laboratory apparatus and the rate and total quantity of off-gas were measured. Samples of the off-gas were also analyzed. The quantity and type of solids remaining (when visible) were determined after post-dissolution filtration of the solution. Recommended conditions for dissolution of the NpO{sub 2} residues are: Solution Matrix and Loading: {approx}50 g Np/L (750 g Np in 15 L of dissolver solution), using 8 M nitric acid (HNO{sub 3}), 0.025 M potassium fluoride (KF) at greater than 100 C for at least 3 hours. Off-gas: Analysis of the off-gas indicated nitric oxide (NO), nitrogen dioxide (NO{sub 2}) and nitrous oxide (N{sub 2}O) as the only identified components. No hydrogen (H{sub 2}) was detected. The molar ratio of off-gas produced per mole of Np dissolved ranged from 0.25 to 0.4 moles of gas per mole of Np dissolved. A peak off-gas rate of {approx}0.1 scfm/kg bulk oxide was observed. Residual Solids: Pure NpO{sub 2} dissolved with little or no residue with the proposed flowsheet but the NpCo and both sweepings samples left visible solid residue after dissolution. For the NpCo and Part II Sweepings samples the residue amounted to {approx}1% of the initial material, but for the Part I Sweepings sample, the residue amounted to {approx}8 % of the initial material. These residues contained primarily aluminum (Al) and silicon (Si) compounds that did not completely dissolve under the flowsheet conditions. The residues from both sweepings samples contained minor amounts of plutonium (Pu) particles. Overall, the undissolved Np and Pu particles in the residues were a very small fraction of the total solids.

Kyser, E

2009-01-12T23:59:59.000Z

116

Document Supply Services Quick Guide  

E-Print Network [OSTI]

, phrase, ISBN/ISSN in the Search Term field (other options are available in the dropdown menu). Note1 Document Supply Services Quick Guide The DSS Portal makes requesting easy! Search for your item and password. If you are having difficulty please read the login help on the main DSS webpage. 2. Enter a word

117

SUPPLY CHAIN MANAGER CHICAGO, IL  

E-Print Network [OSTI]

at project leader to bring best practices into the organization. He or she will recommend solutions to break developing new technology to meet the ever-changing demands of modern industry. The US Headquarters with broad responsibilities that include assessing, managing and improving the supply chain function

Smilowitz, Karen

118

The Arithmetic of Elliptic Curves Theory Conjectures  

E-Print Network [OSTI]

The Arithmetic of Elliptic Curves Theory Conjectures Computations Applications Applications John. Fermat's Last Theorem Frey, Ribet: Counterexample to FLT ) 9 non­modular (semi­stable) elliptic curve

Cremona, John

119

Harmonic algebraic curves and noncrossing partitions  

E-Print Network [OSTI]

Motivated by Gauss’s first proof of the fundamental Theorem of Algebra, we study the topology of harmonic algebraic curves. By the maximum principle, a harmonic curve has no bounded components; its topology is determined ...

Martin, Jeremy L.; Savitt, David; Singer, Ted

2007-02-01T23:59:59.000Z

120

Petroleum supply monthly, June 1993  

SciTech Connect (OSTI)

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures ih the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. Most time series include preliminary estimates for one month based on the Weekly Petroleum Supply Reporting System; statistics based on the most recent data from the Monthly Petroleum Supply Reporting System (MPSRS); and statistics published in prior issues of the PSM and PSA. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas - - the United States (50 States and the District of Columbia), five PAD Districts, and 12 Refining Districts. At the US and PAD District level, the total volume and the daily rate of activities are presented. The statistics are developed from monthly survey forms submitted by respondents to the EIA and from data provided firom other sources.

Not Available

1993-06-28T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Petroleum supply monthly, March 1994  

SciTech Connect (OSTI)

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. Most time series include preliminary estimates for one month based on the Weekly Petroleum Supply Reporting System; statistics based on the most recent data from the Monthly Petroleum Supply Reporting System (MPSRS); and statistics published in prior issues of the PSM and PSA. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas -- the United States (50 States and the District of Columbia), five PAD Districts, and 12 Refining Districts. At the US and PAD District level, the total volume and the daily rate of activities are presented. The statistics are developed from monthly survey forms submitted by respondents to the EIA and from data provided from other sources.

Not Available

1994-03-30T23:59:59.000Z

122

Fastbus Power Supply Manual University of Washington Seattle, 26 March, 1996 Fastbus Power Supplies  

E-Print Network [OSTI]

supplies each have their own built­in cooling fans, and the lower­current supplies are sufficiently cooledFastbus Power Supply Manual University of Washington Seattle, 26 March, 1996 page 1 Fastbus Power Supplies HGB, 03/26/1996 Overview Each of the four Fastbus crates of the SuperK OD DAQ system is supplied

Berns, Hans-Gerd

123

Multipath Curved Planar Reformation of the Peripheral  

E-Print Network [OSTI]

Multipath Curved Planar Reformation of the Peripheral Arterial Tree in CT Angiography1 Justus that cause artifacts in multipath curved planar reformations (MPCPRs) of the peripheral arterial tree in 10-oblique multiplanar reformations perpendicular to the ves- sel centerline (10), and curved planar reformations

124

Reciprocal Relations Between Kinetic Curves  

E-Print Network [OSTI]

We study coupled irreversible processes. For linear or linearized kinetics with microreversibility, $\\dot{x}=Kx$, the kinetic operator $K$ is symmetric in the entropic inner product. This form of Onsager's reciprocal relations implies that the shift in time, $\\exp (Kt)$, is also a symmetric operator. This generates reciprocity relations between kinetic curves. For example, for the Master equation, if we start the process from the $i$th pure state and measure the probability $p_j(t)$ of the $j$th state ($j\

Yablonsky, G S; Constales, D; Galvita, V; Marin, G B

2010-01-01T23:59:59.000Z

125

Petroluem Supply Monthly, May 1993  

SciTech Connect (OSTI)

Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Not Available

1993-06-04T23:59:59.000Z

126

Petroleum Supply Monthly, July 1990  

SciTech Connect (OSTI)

Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Not Available

1990-09-28T23:59:59.000Z

127

Water supply and sludge metals  

SciTech Connect (OSTI)

Ultimate sludge disposal is one of the major tasks facing wastewater treatment facilities today. Where adequate farmland exists in proximity to the treatment facility and where sludge characteristics are suitable, land application is often the most economical method. In some cases, however, metal concentrations in the sludge either limit the site life or the application rate to the point where land application is not economical. When metals are above regulatory limits, land application may become impossible. The origin of the metals has largely been credited to industrial users and stormwater runoff and have, in fact, often represented significant sources of metals. Another potentially significant source of metals that has been frequently overlooked is the water supply system (including the distribution and home piping systems). Data from some treatment facilities suggest that the water supply system is the major source of metals and is the reason that sewage sludge metal levels are above allowable land application limits.

Brown, W.E. (Wright-Pierce Engineers, Topsham, ME (USA))

1988-04-01T23:59:59.000Z

128

High voltage DC power supply  

DOE Patents [OSTI]

A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively. 7 figs.

Droege, T.F.

1989-12-19T23:59:59.000Z

129

High voltage DC power supply  

DOE Patents [OSTI]

A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively.

Droege, Thomas F. (Batavia, IL)

1989-01-01T23:59:59.000Z

130

Emergency Food and Water Supplies  

E-Print Network [OSTI]

E-11 5-99 Emergency Food and Water Supplies Peggy Van Laanen* Cleaning and Sanitizing Equipment After Any Disaster Emergency Food Preparation Equipment Needs Assembling an Emergency... sealed, airtight metal lids, are safe to use after being thoroughly cleaned and sanitized. All cans, free of rust or dents, must be washed and sanitized before they are opened. Wash containers in a detergent solution using a scrub brush. Rinse...

Van Laanen, Peggy

1999-05-14T23:59:59.000Z

131

Supply Stores | Department of Energy  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy UsageAUDITVehicles »ExchangeDepartmentResolveFutureSupercomputers'of EnergySupply

132

Feedstock Supply | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative Fuels DataCombined Heat & PowerEnergy BlogExchangeSummaryFederalLogisticsSupply

133

ABSTRACT: Bioenergy Harvesting Technologies to Supply Crop Residues In a Densified Large Square Bale Format  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-Up from theDepartment(October-DecemberBasedToward a MoreA RisingA1AFrom AARP,ABB

134

Supply chain management in the cement industry  

E-Print Network [OSTI]

Traditionally supply chain management has played an operational role within cement and mineral extraction commodity companies. Recently, cost reduction projects have brought supply chain management into the limelight. In ...

Agudelo, Isabel

2009-01-01T23:59:59.000Z

135

Petroleum Supply Annual 2005, Volume 1  

Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

Supply Annual 2005, Volume 1 Released: October 23, 2006 Petroleum Supply Annual 2005, Volume 1 --- All Tables in PDF (1.0 MB) CSV XLS --- All CSV and XLS files contained in a...

136

Supply Chain Management Faculty Brian Fugate  

E-Print Network [OSTI]

relationships, strategy and sustainability in the supply chain, and she won the College of Business Excellence involvement in new product development, and sustainability practices in supply chain management. He has

137

An integrative framework for architecting supply chains  

E-Print Network [OSTI]

This thesis explores the limitations of classic models of supply chain management, and proposes a new view based on the concept of value-driven supply chains, and a method of analysis and design based on the concepts of ...

Cela Díaz, Fernando

2006-01-01T23:59:59.000Z

138

Charlotte Green Supply Chain: Residential Retrofitting | Department...  

Broader source: Energy.gov (indexed) [DOE]

Charlotte Green Supply Chain: Residential Retrofitting Charlotte Green Supply Chain: Residential Retrofitting July 30, 2010 - 10:50am Addthis Joshua DeLung What does this mean for...

139

Loss of coordination in competitive supply chains  

E-Print Network [OSTI]

The loss of coordination in supply chains quantifies the inefficiency (i.e. the loss of total profit) due to the presence of competition in the supply chain. In this thesis, we discuss four models: one model with multiple ...

Teo, Koon Soon

2009-01-01T23:59:59.000Z

140

Coupling Renewable Energy Supply with Deferrable Demand  

E-Print Network [OSTI]

Scale Renewable Energy Integration . . . . . . . . . . .Impacts of Renewable Energy Supply . . . . . . . . . . . . .1.3 Coupling Renewable Energy with Deferrable

Papavasiliou, Anthony

2011-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Agents on the Web Supply Chains  

E-Print Network [OSTI]

Agents on the Web Automating Supply Chains 90 JULY · AUGUST 2001 http://computer.org/internet/ 1089

Almor, Amit

142

Nuclear reactor with makeup water assist from residual heat removal system  

DOE Patents [OSTI]

A pressurized water nuclear reactor uses its residual heat removal system to make up water in the reactor coolant circuit from an in-containment refueling water supply during staged depressurization leading up to passive emergency cooling by gravity feed from the refueling water storage tank, and flooding of the containment building. When depressurization commences due to inadvertence or a manageable leak, the residual heat removal system is activated manually and prevents flooding of the containment when such action is not necessary. Operation of the passive cooling system is not impaired. A high pressure makeup water storage tank is coupled to the reactor coolant circuit, holding makeup coolant at the operational pressure of the reactor. The staged depressurization system vents the coolant circuit to the containment, thus reducing the supply of makeup coolant. The level of makeup coolant can be sensed to trigger opening of successive depressurization conduits. The residual heat removal pumps move water from the refueling water storage tank into the coolant circuit as the coolant circuit is depressurized, preventing reaching the final depressurization stage unless the makeup coolant level continues to drop. The residual heat removal system can also be coupled in a loop with the refueling water supply tank, for an auxiliary heat removal path.

Corletti, Michael M. (New Kensington, PA); Schulz, Terry L. (Murrysville, PA)

1993-01-01T23:59:59.000Z

143

Nuclear reactor with makeup water assist from residual heat removal system  

DOE Patents [OSTI]

A pressurized water nuclear reactor uses its residual heat removal system to make up water in the reactor coolant circuit from an in-containment refueling water supply during staged depressurization leading up to passive emergency cooling by gravity feed from the refueling water storage tank, and flooding of the containment building. When depressurization commences due to inadvertence or a manageable leak, the residual heat removal system is activated manually and prevents flooding of the containment when such action is not necessary. Operation of the passive cooling system is not impaired. A high pressure makeup water storage tank is coupled to the reactor coolant circuit, holding makeup coolant at the operational pressure of the reactor. The staged depressurization system vents the coolant circuit to the containment, thus reducing the supply of makeup coolant. The level of makeup coolant can be sensed to trigger opening of successive depressurization conduits. The residual heat removal pumps move water from the refueling water storage tank into the coolant circuit as the coolant circuit is depressurized, preventing reaching the final depressurization stage unless the makeup coolant level continues to drop. The residual heat removal system can also be coupled in a loop with the refueling water supply tank, for an auxiliary heat removal path. 2 figures.

Corletti, M.M.; Schulz, T.L.

1993-12-07T23:59:59.000Z

144

Supply Chain and Information Sciences Technology 2010  

E-Print Network [OSTI]

Supply Chain and Information Sciences Technology 2010 Supply Chain and Information Systems Technology Minor SCIST Minor Application Department of Supply Chain & Information Systems College of Information Sciences and Technology Overview The minor in SCIST is structured to provide students not majoring

Guiltinan, Mark

145

Heat Supply Who What Where and -Why  

E-Print Network [OSTI]

heat and power plants (CHP) and other heat technologies ...................................10 2Heat Supply in Denmark Who What Where and - Why #12;Title: Heat Supply in Denmark - Who What Where: MONTAGEbureauet Aps Printing: Kailow Graphic Cover photo: Miklos Szabo #12;HEAT SUPPLY IN DENMARK WHO WHAT WHERE

Columbia University

146

Hg supply piping simulation Stony Brook University  

E-Print Network [OSTI]

Hg supply piping simulation (No MHD) Stony Brook University Yan Zhan Prof. Foluso Ladeinde July 2nd, 2010 #12;Outline · Hg supply piping in Muon Collider · Turbulence models for bend pipe flow · Problems need studying · Arrangements in the near future #12;Outline · Hg supply piping in Muon Collider ­ Hg

McDonald, Kirk

147

AE: Office Supplies Purchasing Stakeholder Survey Notes  

E-Print Network [OSTI]

AE: Office Supplies Purchasing Stakeholder Survey Notes Updated: 2/20/2012 Overview: · Survey Purchasing Factors: · 37% of people make office supplies purchases monthly, 26% weekly, and 15% quarterly used vendors for office supplies · People mostly purchase from vendors other than Staples due

Sheridan, Jennifer

148

Petroleum supply monthly: December 1993  

SciTech Connect (OSTI)

Data are presented which describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States. Data are presented in two sections: Summary Statistics, presenting a time series of selected petroleum data on a U.S. level, and Detailed Statistics, presenting statistics for the most current month available as well as year to date.

Not Available

1993-12-01T23:59:59.000Z

149

Propylene feedstock: supply and demand  

SciTech Connect (OSTI)

The reasons for the global shortage in propylene in 1981-82 are discussed. The low running rates of ethylene production and refinery operation of which propylene is a byproduct accounts for the reduced propylene supplies. Low prices of the NCL have also shifted incentive from propylene to gas liquids. This situation will continue, with naptha/gas oil becoming the prefered feedstock for ethylene production. The speculative economics for propylene dehydrogenation are not sufficiently attractive for commercialization. But if a country has an internal market for propylene derivatives, production could have a positive influence on the economy. Thailand, Indonesia, Malaysia, and Mexico are suggested as examples.

Steinbaum, C.A.; Pickover, B.H.

1983-04-01T23:59:59.000Z

150

UV Light Curves of Thermonuclear Supernovae  

E-Print Network [OSTI]

Ultraviolet light curves are calculated for several thermonuclear supernova models using a multifrequency radiation hydrodynamic code. It is found that Chandrasekhar-mass models produce very similar light curves both for detonation and deflagration. Sub-Chandrasekhar-mass models essentially differ from ``normal'' Chandrasekhar ones regarding behaviour of their UV fluxes. Differences in absolute brightness and in shape of light curves of thermonuclear supernovae could be detectable up to 300 Mpc with modern UV space telescopes.

S. I. Blinnikov; E. I. Sorokina

2000-03-17T23:59:59.000Z

151

The Arithmetic of Elliptic Curves Theory Conjectures  

E-Print Network [OSTI]

Applications John Cremona University of Exeter #12's Last Theorem Frey, Ribet: Counterexample to FLT ) 9 non-modular (semi-stable) elliptic curve over Q

Cremona, John

152

Canonical correlation of shipping forward curves  

E-Print Network [OSTI]

The behavior and interrelations between the main shipping forward curves are analyzed using multivariate statistics after removing the volatility distortions dictated by the Samuelson hypothesis. Principal Components ...

Hadjiyiannis, Nicholas

2010-01-01T23:59:59.000Z

153

Learning Curve - DOE Directives, Delegations, and Requirements  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

This chapter discusses the development and application of the learning curve. g4301-1chp21.pdf -- PDF Document, 28 KB Writer: John Makepeace Subjects: Administration Management...

154

Quantum fields in curved spacetime  

E-Print Network [OSTI]

We review the theory of quantum fields propagating in an arbitrary, classical, globally hyperbolic spacetime. Our review emphasizes the conceptual issues arising in the formulation of the theory and presents known results in a mathematically precise way. Particular attention is paid to the distributional nature of quantum fields, to their local and covariant character, and to microlocal spectrum conditions satisfied by physically reasonable states. We review the Unruh and Hawking effects for free fields, as well as the behavior of free fields in deSitter spacetime and FLRW spacetimes with an exponential phase of expansion. We review how nonlinear observables of a free field, such as the stress-energy tensor, are defined, as well as time-ordered-products. The "renormalization ambiguities" involved in the definition of time-ordered products are fully characterized. Interacting fields are then perturbatively constructed. Our main focus is on the theory of a scalar field, but a brief discussion of gauge fields is included. We conclude with a brief discussion of a possible approach towards a nonperturbative formulation of quantum field theory in curved spacetime and some remarks on the formulation of quantum gravity.

Stefan Hollands; Robert M. Wald

2014-06-10T23:59:59.000Z

155

Effects of the drought on California electricity supply and demand  

E-Print Network [OSTI]

ELECTRICITY SUPPLY Hydroelectric Energy Supply Thermal-question. Data on PG&E's hydroelectric resources and Pacific27 Table 28 Table 29 Hydroelectric Supply in California Fuel

Benenson, P.

2010-01-01T23:59:59.000Z

156

Transforms for prediction residuals in video coding  

E-Print Network [OSTI]

Typically the same transform, the 2-D Discrete Cosine Transform (DCT), is used to compress both image intensities in image coding and prediction residuals in video coding. Major prediction residuals include the motion ...

Kam??l?, Fatih

2010-01-01T23:59:59.000Z

157

DETERMINISTIC COMPONENTS IN THE LIGHT CURVE AMPLITUDE OF Y OPH  

SciTech Connect (OSTI)

About two decades after the discovery of the amplitude decline of the light curve of the classical Cepheid Y Oph, its study is resumed using an increased amount of homogenized data and an extended time base. In our approach, the investigation of different time series concerning the light curve amplitude of Y Oph is not only the reason for the present study, but also a stimulus for developing a coherent methodology for studying long- and short-term variability phenomena in variable stars, taking into account the details of concrete observing conditions: amount of data, data sampling, time base, and individual errors of observational data. The statistical significance of this decreasing trend was estimated by assuming its linearity. We approached the decision-making process by formulating adequate null and alternative hypotheses, and testing the value of the regression line slope for different data sets via Monte Carlo simulations. A variability analysis, through various methods, of the original data and of the residuals obtained after removing the linear trend was performed. We also proposed a new statistical test, based on amplitude spectrum analysis and Monte Carlo simulations, intended to evaluate how detectible is a given (linear) trend in well-defined observing conditions: the trend detection probability. The main conclusion of our study on Y Oph is that, even if the false alarm probability is low enough to consider the decreasing trend to be statistically significant, the available data do not allow us to obtain a reasonably powerful test. We are able to confirm the light curve amplitude decline, and the order of magnitude of its slope with a better statistical substantiation. According to the obtained values of the trend detection probability, it seems that the trend we are dealing with is marked by a low detectibility. Our attempt to find signs of possible variability phenomena at shorter timescales ended by emphasizing the relative constancy of our data, within their precision limits.

Pop, Alexandru; Turcu, Vlad [Astronomical Institute of the Romanian Academy, Astronomical Observatory Cluj-Napoca, Str. Ciresilor 19, 400487 Cluj-Napoca (Romania); Vamos, Calin ['T. Popoviciu' Institute of Numerical Analysis, Romanian Academy, P.O. Box 68, 400110 Cluj-Napoca (Romania)], E-mail: andi_pop@yahoo.com, E-mail: vladturcu@yahoo.com, E-mail: cvamos@ictp.acad.ro

2010-02-15T23:59:59.000Z

158

Uninterruptible power supply (UPS) systems  

SciTech Connect (OSTI)

Use of this purchase specification is not mandatory. User should review the document and determine if it meets the user`s purpose. This document contains a fill-in-the-blanks guide specification for the procurement of uninterruptible power supply (UPS) systems greater than 10 kVA, organized as follows: Parts 1 through 7--technical requirements; Appendix A--technical requirements to be included in the proposal; Appendix B--UPS system data sheets to be completed by each bidder (Seller) and submitted with the proposal; Appendix C--general guidelines giving the specifier parameters for selecting a UPS system; it should be read before preparing an actual specification, and is not attached to the specification; Attachment 1--sketches prepared by the purchaser (Owner); Attachment 2--sample title page.

NONE

1997-04-01T23:59:59.000Z

159

Upgrading the TFTR Transrex Power Supplies  

SciTech Connect (OSTI)

In order to provide improved and expanded experimental capabilities, the existing Transrex power supplies at PPPL are to be upgraded and modernized. Each of the 39 power supplies consists of two six pulse silicon controlled rectifier sections forming a twelve pulse power supply. The first modification is to split each supply into two independent six pulse supplies by replacing the existing obsolete twelve pulse firing generator with two commercially available six pulse firing generators. The second change replaces the existing control link with a faster system, with greater capacity, which will allow for independent control of all 78 power supply sections. The third change replaces the existing Computer Automated Measurement and Control (CAMAC) based fault detector with an Experimental Physics and Industrial Control System (EPICS) compatible unit, eliminating the obsolete CAMAC modules. Finally the remaining relay logic and interfaces to the "Hardwired Control System" will be replaces with a Programmable Logic Controller (PLC).

J. E. Lawson, R. Marsala, S. Ramakrishnan, X. Zhao, P. Sichta

2009-05-29T23:59:59.000Z

160

Petroleum supply annual 1995: Volume 1  

SciTech Connect (OSTI)

The {ital Petroleum Supply Annual} contains information on supply and disposition of crude oil and petroleum products. It reflects data collected from the petroleum industry during 1995 through monthly surveys, and it is divided into 2 volumes. This volume contains three sections: summary statistics, detailed statistics, and selected refinery statistics, each with final annual data. (The other volume contains final statistics for each month and replaces data previously published in the {ital Petroleum Supply Monthly}).

NONE

1996-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Shock-activated electrochemical power supplies  

DOE Patents [OSTI]

A shock-activated electrochemical power supply is provided which is initiated extremely rapidly and which has a long shelf life. Electrochemical power supplies of this invention are initiated much faster than conventional thermal batteries. Power supplies of this invention comprise an inactive electrolyte and means for generating a high-pressure shock wave such that the shock wave is propagated through the electrolyte rendering the electrolyte electrochemically active. 2 figs.

Benedick, W.B.; Graham, R.A.; Morosin, B.

1987-04-20T23:59:59.000Z

162

Shock-activated electrochemical power supplies  

DOE Patents [OSTI]

A shock-activated electrochemical power supply is provided which is initiated extremely rapidly and which has a long shelf life. Electrochemical power supplies of this invention are initiated much faster than conventional thermal batteries. Power supplies of this invention comprise an inactive electrolyte and means for generating a high-pressure shock wave such that the shock wave is propagated through the electrolytes rendering the electrolyte electrochemically active. 2 figs.

Benedick, W.B.; Graham, R.A.; Morosin, B.

1988-11-08T23:59:59.000Z

163

Process to recycle shredder residue  

DOE Patents [OSTI]

A system and process for recycling shredder residue, in which separating any polyurethane foam materials are first separated. Then separate a fines fraction of less than about 1/4 inch leaving a plastics-rich fraction. Thereafter, the plastics rich fraction is sequentially contacted with a series of solvents beginning with one or more of hexane or an alcohol to remove automotive fluids; acetone to remove ABS; one or more of EDC, THF or a ketone having a boiling point of not greater than about 125.degree. C. to remove PVC; and one or more of xylene or toluene to remove polypropylene and polyethylene. The solvents are recovered and recycled.

Jody, Bassam J. (Chicago, IL); Daniels, Edward J. (Oak Lawn, IL); Bonsignore, Patrick V. (Channahon, IL)

2001-01-01T23:59:59.000Z

164

Investigation of learning and experience curves  

SciTech Connect (OSTI)

The applicability of learning and experience curves for predicting future costs of solar technologies is assessed, and the major test case is the production economics of heliostats. Alternative methods for estimating cost reductions in systems manufacture are discussed, and procedures for using learning and experience curves to predict costs are outlined. Because adequate production data often do not exist, production histories of analogous products/processes are analyzed and learning and aggregated cost curves for these surrogates estimated. If the surrogate learning curves apply, they can be used to estimate solar technology costs. The steps involved in generating these cost estimates are given. Second-generation glass-steel and inflated-bubble heliostat design concepts, developed by MDAC and GE, respectively, are described; a costing scenario for 25,000 units/yr is detailed; surrogates for cost analysis are chosen; learning and aggregate cost curves are estimated; and aggregate cost curves for the GE and MDAC designs are estimated. However, an approach that combines a neoclassical production function with a learning-by-doing hypothesis is needed to yield a cost relation compatible with the historical learning curve and the traditional cost function of economic theory.

Krawiec, F.; Thornton, J.; Edesess, M.

1980-04-01T23:59:59.000Z

165

R&D ERL: Power Supplies  

SciTech Connect (OSTI)

A magnet power supply system has been developed to meet the field requirements of the ERL in a compact and cost effective fashion.

Lambiase, R.

2010-01-01T23:59:59.000Z

166

GI Self-Supply Pilot Overview  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

BPA TRANSMISSION SERVICES Transmission Wind Integration Systems Team GENERATION IMBALANCE SELF SUPPLY PILOT PROJECT OVERVIEW VERSION: 0.1 UPDATED: 7292009 giself-supplypilotov...

167

Assessing reliability in energy supply systems  

E-Print Network [OSTI]

pathway supplying hydrogen via pipeline from a centralizedgas with pipeline distribution of hydrogen, and 2) on-sitehydrogen is transported to the refueling stations via pipeline

McCarthy, Ryan W.; Ogden, Joan M.; Sperling, Daniel

2007-01-01T23:59:59.000Z

168

Assessing Reliability in Energy Supply Systems  

E-Print Network [OSTI]

pathway supplying hydrogen via pipeline from a centralizedgas with pipeline distribution of hydrogen, and 2) on-sitehydrogen is transported to the refueling stations via pipeline

McCarthy, Ryan; Ogden, Joan M.; Sperling, Dan

2008-01-01T23:59:59.000Z

169

Assessing reliability in energy supply systems  

E-Print Network [OSTI]

liquefied natural gas (LNG) trading expected to increase insteam reformation production facility using imported LNG.The LNG supplies come primarily from Trinidad and Tobago,

McCarthy, Ryan W.; Ogden, Joan M.; Sperling, Daniel

2007-01-01T23:59:59.000Z

170

Assessing Reliability in Energy Supply Systems  

E-Print Network [OSTI]

liquefied natural gas (LNG) trading expected to increase insteam reformation production facility using imported LNG.The LNG supplies come primarily from Trinidad and Tobago,

McCarthy, Ryan; Ogden, Joan M.; Sperling, Dan

2008-01-01T23:59:59.000Z

171

Covered Product Category: Uninterruptible Power Supplies (for...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Program (FEMP) provides acquisition guidance for uninterruptible power supplies (UPS), a product category covered by the ENERGY STAR program. Federal laws and requirements...

172

Electrical Power Supply Applications Engineer | Princeton Plasma...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Electrical Power Supply Applications Engineer Department: Engineering Supervisor(s): John Lacenere Staff: ENG 04 Requisition Number: 1400303 The Princeton University Plasma Physics...

173

Advanced Accessory Power Supply Topologies  

SciTech Connect (OSTI)

This Cooperative Research and Development Agreement (CRADA) began December 8, 2000 and ended September 30, 2009. The total funding provided by the Participant (General Motors Advanced Technology Vehicles [GM]) during the course of the CRADA totaled $1.2M enabling the Contractor (UT-Battelle, LLC [Oak Ridge National Laboratory, a.k.a. ORNL]) to contribute significantly to the joint project. The initial task was to work with GM on the feasibility of developing their conceptual approach of modifying major components of the existing traction inverter/drive to develop low cost, robust, accessory power. Two alternate methods for implementation were suggested by ORNL and both were proven successful through simulations and then extensive testing of prototypes designed and fabricated during the project. This validated the GM overall concept. Moreover, three joint U.S. patents were issued and subsequently licensed by GM. After successfully fulfilling the initial objective, the direction and duration of the CRADA was modified and GM provided funding for two additional tasks. The first new task was to provide the basic development for implementing a cascaded inverter technology into hybrid vehicles (including plug-in hybrid, fuel cell, and electric). The second new task was to continue the basic development for implementing inverter and converter topologies and new technology assessments for hybrid vehicle applications. Additionally, this task was to address the use of high temperature components in drive systems. Under this CRADA, ORNL conducted further research based on GM’s idea of using the motor magnetic core and windings to produce bidirectional accessory power supply that is nongalvanically coupled to the terminals of the high voltage dc-link battery of hybrid vehicles. In order not to interfere with the motor’s torque, ORNL suggested to use the zero-sequence, highfrequency harmonics carried by the main fundamental motor current for producing the accessory power. Two studies were conducted at ORNL. One was to put an additional winding in the motor slots to magnetically link with the high frequency of the controllable zero-sequence stator currents that do not produce any zero-sequence harmonic torques. The second approach was to utilize the corners of the square stator punching for the high-frequency transformers of the dc/dc inverter. Both approaches were successful. This CRADA validated the feasibility of GM’s desire to use the motor’s magnetic core and windings to produce bidirectional accessory power supply. Three joint U.S. patents with GM were issued to ORNL and GM by the U.S. Patent Office for the research results produced by this CRADA.

Marlino, L.D.

2010-06-15T23:59:59.000Z

174

Reshaping the electricity supply industry  

SciTech Connect (OSTI)

Cigre`s Electra magazine published this interview with Alfonso Limbruno, CEO of ENEL S.p.A. To put the interview in perspective, this article begins with a brief overview of ENEL and a biographical sketch of Alfonso Limbruno, and also carries comments from Y. Thomas, secretary general of CIGRE. ENEL is a vertically integrated nationwide electricity company engaged in the generation, transmission, distribution, and sale of electricity, predominantly in Italy. ENEL`s share accounts for approximately 80 percent of Italian electricity demand. Measured by amount of electricity sold, ENEL is the third largest electric utility in the OECD countries and the second largest electric utility in Europe. Measured by revenues, ENEL is one of the largest companies in Italy, with a turnover of Lit. 37,632 billion. In 1995, ENEL served approximately 28.5 million customers and sold 211,607 GWh of electricity. ENEL`s gross installed generating capacity at December 31, 1995 was 55,906 MW. Alfonso Limbruno made all his career in the Italian electricity supply industry (ESI) and has had quite a unique experience: he went through a complete cycle of change of the ESI in his country, the nationalization of the sector in 1962 with the merging in ENEL of over 1,200 undertakings, and now the privatization of the company, along with a far reaching restructuring of the industry. He was appointed CEO of ENEL in August 1992.

NONE

1997-03-01T23:59:59.000Z

175

Protective supplied breathing air garment  

DOE Patents [OSTI]

A breathing air garment is disclosed for isolating a wearer from hostile environments containing toxins or irritants includes a suit and a separate head protective enclosure or hood engaging a suit collar in sealing attachment. The hood and suit collar are cylindrically shaped and dimensioned to enable the wearer to withdraw his hands from the suit sleeves to perform manual tasks within the hood interior. Breathing air is supplied from an external air line with an air delivery hose attached to the hood interior. The hose feeds air into an annular halo-like fiber-filled plenum having spaced discharge orifices attached to the hood top wall. A plurality of air exhaust/check valves located at the suit extremities cooperate with the hood air delivery system to provide a cooling flow of circulating air from the hood throughout the suit interior. A suit entry seal provided on the suit rear torso panel permits access into the suit and is sealed with an adhesive sealing flap. 17 figs.

Childers, E.L.; Hortenau, E.F. von.

1984-07-10T23:59:59.000Z

176

Supply Chain The effective supply chain has become a new organizational and operational  

E-Print Network [OSTI]

MBA in Supply Chain Management #12;The effective supply chain has become a new organizational a virtual integration of business partners to achieve new levels of efficiency and productivity, as well

Lin, Xiaodong

177

Certified Professional in Supply Management (CPSM) Review Series: Exam 2: Effective Supply Management Performance  

E-Print Network [OSTI]

· Materials and Inventory Management · Organization/Department Assessment · Planning · Product and ServiceCertified Professional in Supply Management (CPSM) Review Series: Exam 2: Effective Supply Management Performance Dates: October 28, 2011 Location: Rutgers University­ Livingston Campus, Tillett Hall

178

U.S. Billion-Ton Update: Biomass Supply for a Bioenergy and Bioproducts Industry  

SciTech Connect (OSTI)

The report, Biomass as Feedstock for a Bioenergy and Bioproducts Industry: The Technical Feasibility of a Billion-Ton Annual Supply (generally referred to as the Billion-Ton Study or 2005 BTS), was an estimate of 'potential' biomass based on numerous assumptions about current and future inventory, production capacity, availability, and technology. The analysis was made to determine if conterminous U.S. agriculture and forestry resources had the capability to produce at least one billion dry tons of sustainable biomass annually to displace 30% or more of the nation's present petroleum consumption. An effort was made to use conservative estimates to assure confidence in having sufficient supply to reach the goal. The potential biomass was projected to be reasonably available around mid-century when large-scale biorefineries are likely to exist. The study emphasized primary sources of forest- and agriculture-derived biomass, such as logging residues, fuel treatment thinnings, crop residues, and perennially grown grasses and trees. These primary sources have the greatest potential to supply large, reliable, and sustainable quantities of biomass. While the primary sources were emphasized, estimates of secondary residue and tertiary waste resources of biomass were also provided. The original Billion-Ton Resource Assessment, published in 2005, was divided into two parts-forest-derived resources and agriculture-derived resources. The forest resources included residues produced during the harvesting of merchantable timber, forest residues, and small-diameter trees that could become available through initiatives to reduce fire hazards and improve forest health; forest residues from land conversion; fuelwood extracted from forests; residues generated at primary forest product processing mills; and urban wood wastes, municipal solid wastes (MSW), and construction and demolition (C&D) debris. For these forest resources, only residues, wastes, and small-diameter trees were considered. The 2005 BTS did not attempt to include any wood that would normally be used for higher-valued products (e.g., pulpwood) that could potentially shift to bioenergy applications. This would have required a separate economic analysis, which was not part of the 2005 BTS. The agriculture resources in the 2005 BTS included grains used for biofuels production; crop residues derived primarily from corn, wheat, and small grains; and animal manures and other residues. The cropland resource analysis also included estimates of perennial energy crops (e.g., herbaceous grasses, such as switchgrass, woody crops like hybrid poplar, as well as willow grown under short rotations and more intensive management than conventional plantation forests). Woody crops were included under cropland resources because it was assumed that they would be grown on a combination of cropland and pasture rather than forestland. In the 2005 BTS, current resource availability was estimated at 278 million dry tons annually from forestlands and slightly more than 194 million dry tons annually from croplands. These annual quantities increase to about 370 million dry tons from forestlands and to nearly 1 billion dry tons from croplands under scenario conditions of high-yield growth and large-scale plantings of perennial grasses and woody tree crops. This high-yield scenario reflects a mid-century timescale ({approx}2040-2050). Under conditions of lower-yield growth, estimated resource potential was projected to be about 320 and 580 million dry tons for forest and cropland biomass, respectively. As noted earlier, the 2005 BTS emphasized the primary resources (agricultural and forestry residues and energy crops) because they represent nearly 80% of the long-term resource potential. Since publication of the BTS in April 2005, there have been some rather dramatic changes in energy markets. In fact, just prior to the actual publication of the BTS, world oil prices started to increase as a result of a burgeoning worldwide demand and concerns about long-term supplies. By the end of the summer, oil pri

Downing, Mark [ORNL; Eaton, Laurence M [ORNL; Graham, Robin Lambert [ORNL; Langholtz, Matthew H [ORNL; Perlack, Robert D [ORNL; Turhollow Jr, Anthony F [ORNL; Stokes, Bryce [Navarro Research & Engineering; Brandt, Craig C [ORNL

2011-08-01T23:59:59.000Z

179

Classification and forecasting of load curves Nolwen Huet  

E-Print Network [OSTI]

Classification and forecasting of load curves Nolwen Huet Abstract The load curve, which gives of electricity customer uses. This load curve is only available for customers with automated meter reading. For the others, EDF must estimate this curve. Usually a clustering of the load curves is performed, followed

Cuesta, Juan Antonio

180

Diffusion-Limited Aggregation on Curved Surfaces  

E-Print Network [OSTI]

We develop a general theory of transport-limited aggregation phenomena occurring on curved surfaces, based on stochastic iterated conformal maps and conformal projections to the complex plane. To illustrate the theory, we ...

Choi, J.

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Learning Curve Management in Educational Programming Environments  

E-Print Network [OSTI]

Learning Curve Management in Educational Programming Environments Benjamin H. Brinckerhoff Computer programmers are best served by integrated development environments that adapt to their growing sophistication programming environments. We provide pedagogical justification for each goal, describe possible supporting

Goldman, Kenneth J.

182

Chiral gap effect in curved space  

E-Print Network [OSTI]

We discuss a new type of QCD phenomenon induced in curved space. In the QCD vacuum a mass gap of Dirac fermions is attributed to the spontaneous breaking of chiral symmetry. If the curvature is positive large, the chiral condensate melts but a chiral invariant mass gap can still remain, which we name the chiral gap effect in curved space. This leads to decoupling of quark deconfinement which implies a view of black holes surrounded by a first-order QCD phase transition.

Antonino Flachi; Kenji Fukushima

2014-06-25T23:59:59.000Z

183

Biomass Supply and Carbon Accounting for  

E-Print Network [OSTI]

Biomass Supply and Carbon Accounting for Southeastern Forests February 2012 #12;This Biomass Supply and Carbon Accounting for Southeastern Forests study was conducted by the Biomass Energy Resource Center Biomass Energy Resource Center Kamalesh Doshi Biomass Energy Resource Center Hillary Emick Biomass Energy

184

Supply Chain Networks: Challenges and Opportunities  

E-Print Network [OSTI]

School of Management University of Massachusetts Amherst, Massachusetts 01003 Department of Management, and consumers at the demand markets. Today, supply chains may span thousands of miles across the globe, involve as the stability and resiliency of supply chains, as well as their adaptability and responsiveness to events

Nagurney, Anna

185

Supply Chains and Transportation Networks Anna Nagurney  

E-Print Network [OSTI]

Management Isenberg School of Management University of Massachusetts Amherst, Massachusetts 01003 December, and consumers at the demand markets. Supply chains are the backbones of our globalized Network Economy of cooperation. For example, in a vertically integrated supply chain the same firm may be responsible

Nagurney, Anna

186

EXOTIC OPTIONS FOR INTERRUPTIBLE ELECTRICITY SUPPLY CONTRACTS  

E-Print Network [OSTI]

the last decade have been directed at increasing competition in the generation of electricity. This hasEXOTIC OPTIONS FOR INTERRUPTIBLE ELECTRICITY SUPPLY CONTRACTS RAJNISH KAMAT and SHMUEL S. OREN of financial contracts for the supply and procurement of interruptible electricity service. While the contract

187

Response to changes in demand/supply  

E-Print Network [OSTI]

Response to changes in demand/supply through improved marketing 21.2 #12;#12;111 Impacts of changes log demand in 1995. The composites board mills operating in Korea took advantage of flexibility environment changes on the production mix, some economic indications, statistics of demand and supply of wood

188

Response to changes in demand/supply  

E-Print Network [OSTI]

Response to changes in demand/supply through improved marketing 21.2 http with the mill consuming 450 000 m3 , amounting to 30% of total plywood log demand in 1995. The composites board, statistics of demand and supply of wood, costs and competitiveness were analysed. The reactions

189

Internal Markets for Supply Chain Capacity Allocation  

E-Print Network [OSTI]

Internal Markets for Supply Chain Capacity Allocation David McAdams and Thomas W. Malone Sloan David McAdams & Thomas Malone #12;Internal Markets for Supply Chain Capacity Allocation David Mc ("internal markets") to help allocate manufacturing capacity and determine the prices, delivery dates

190

Finance and supply management project execution plan  

SciTech Connect (OSTI)

As a subproject of the HANDI 2000 project, the Finance and Supply Management system is intended to serve FDH and Project Hanford major subcontractor with financial processes including general ledger, project costing, budgeting, and accounts payable, and supply management process including purchasing, inventory and contracts management. Currently these functions are performed with numerous legacy information systems and suboptimized processes.

BENNION, S.I.

1999-02-10T23:59:59.000Z

191

Research on External Power Supplies Will Save  

E-Print Network [OSTI]

. PIER's work led to major collaboration among federal agencies, industry partners, and others, which Are Abundant and Wasteful Example of typical external power supply use Source: Pacific Gas and Electric Most office equipment and consumer electronic devices use external power supplies to convert the electricity

192

SUMMER 2007 ELECTRICITY SUPPLY AND DEMAND OUTLOOK  

E-Print Network [OSTI]

CALIFORNIA ENERGY COMMISSION SUMMER 2007 ELECTRICITY SUPPLY AND DEMAND OUTLOOK DRAFTSTAFFREPORT May ELECTRICITY ANALYSIS OFFICE Sylvia Bender Acting Deputy Director ELECTRICITY SUPPLY ANALYSIS DIVISION B. B assessment of the capability of the physical electricity system to provide power to meet electricity demand

193

Proposal for the Cryogenic Supply of a  

E-Print Network [OSTI]

1 Proposal for the Cryogenic Supply of a Single TTF / FEL - Cryomodule Test Bench TESLA Report No supply are described. 1. Introduction For the time being, TTF- cryomodules can only be cold tested after will change. The quadrupoles will be cooled in the 2.0 K liquid bath instead by the 4.5K cooling circuit

194

Transportation Energy: Supply, Demand and the Future  

E-Print Network [OSTI]

Transportation Energy: Supply, Demand and the Future http://www.uwm.edu/Dept/CUTS//2050/energy05 as a source of energy. Global supply and demand trends will have a profound impact on the ability to use our) Transportation energy demand in the U.S. has increased because of the greater use of less fuel efficient vehicles

Saldin, Dilano

195

Hierarchical Hybrid Power Supply Networks Farinaz Koushanfar  

E-Print Network [OSTI]

Hierarchical Hybrid Power Supply Networks Farinaz Koushanfar Electrical & Computer Engineering management, hybrid power supply, supercapacitors 1. INTRODUCTION AND MOTIVATION Historically, almost all, but the DRAM power consumption is typically around six times lower than SRAM power usage. Depending on the task

196

A Supply Chain Network Perspective for Electric Power Generation, Supply, Transmission, and Consumption  

E-Print Network [OSTI]

A Supply Chain Network Perspective for Electric Power Generation, Supply, Transmission, and Consumption Anna Nagurney and Dmytro Matsypura Department of Finance and Operations Management Isenberg School, Berlin, Germany, pp. 3-27. Abstract: A supply chain network perspective for electric power production

Nagurney, Anna

197

Supply Chain Networks, Electronic Commerce, and Supply Side and Demand Side Risk  

E-Print Network [OSTI]

Supply Chain Networks, Electronic Commerce, and Supply Side and Demand Side Risk Anna Nagurney as well as demand side risk are included in the formulation. The model consists of three tiers of decision chain network equilibrium model with electronic com- merce and with supply side and demand side risk

Nagurney, Anna

198

Introduction The Sustainable Supply Chain Taxes Permits Integration Future Research Sustainable Supply Chains  

E-Print Network [OSTI]

Introduction The Sustainable Supply Chain Taxes Permits Integration Future Research Sustainable;Introduction The Sustainable Supply Chain Taxes Permits Integration Future Research 1 Introduction 2 The Sustainable Supply Chain 3 Taxes 4 Permits 5 Integration 6 Future Research Dissertation Defense by Trisha D

Nagurney, Anna

199

Certified Professional in Supply Management (CPSM) & Certified in Supply Management (CSM) Exam Preparation Series  

E-Print Network [OSTI]

-Taking Hints and Tips Exam 2 Content Forecasting Logistics Materials and Inventory Management OrganizationCertified Professional in Supply Management (CPSM) & Certified in Supply Management (CSM) Exam for member companies of the Rutgers Center for Supply Chain Management. $425 for non-members This one day

Lin, Xiaodong

200

Environmental bias and elastic curves on surfaces  

E-Print Network [OSTI]

The behavior of an elastic curve bound to a surface will reflect the geometry of its environment. This may occur in an obvious way: the curve may deform freely along directions tangent to the surface, but not along the surface normal. However, even if the energy itself is symmetric in the curve's geodesic and normal curvatures, which control these modes, very distinct roles are played by the two. If the elastic curve binds preferentially on one side, or is itself assembled on the surface, not only would one expect the bending moduli associated with the two modes to differ, binding along specific directions, reflected in spontaneous values of these curvatures, may be favored. The shape equations describing the equilibrium states of a surface curve described by an elastic energy accommodating environmental factors will be identified by adapting the method of Lagrange multipliers to the Darboux frame associated with the curve. The forces transmitted to the surface along the surface normal will be determined. Features associated with a number of different energies, both of physical relevance and of mathematical interest, are described. The conservation laws associated with trajectories on surface geometries exhibiting continuous symmetries are also examined.

Jemal Guven; Dulce María Valencia; Pablo Vázquez-Montejo

2014-08-15T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Coal slurry fuel supply and purge system  

DOE Patents [OSTI]

A coal slurry fuel supply and purge system for a locomotive engines is disclosed which includes a slurry recirculation path, a stand-by path for circulating slurry during idle or states of the engine when slurry fuel in not required by the engine, and an engine header fluid path connected to the stand-by path, for supplying and purging slurry fuel to and from fuel injectors. A controller controls the actuation of valves to facilitate supply and purge of slurry to and from the fuel injectors. A method for supplying and purging coal slurry in a compression ignition engine is disclosed which includes controlling fluid flow devices and valves in a plurality of fluid paths to facilitate continuous slurry recirculation and supply and purge of or slurry based on the operating state of the engine.

McDowell, Robert E. (Fairview, PA); Basic, Steven L. (Hornell, NY); Smith, Russel M. (North East, PA)

1994-01-01T23:59:59.000Z

202

Residual stress patterns in steel welds  

SciTech Connect (OSTI)

Neutron strain scanning of residual stress is a valuable nondestructive tool for evaluation of residual stress in welds. The penetrating characteristic of neutrons permits mapping of strain patterns with a spatial resolution approaching 1mm at depths of 20mm in steels. While the overall patterns of the residual stress tensor in a weld are understood, the detailed patterns depend on welding process parameters and the effects of solid state transformation. The residual strain profiles in two multi-pass austenitic welds and a ferritic steel weld are presented. The stress-free lattice parameters within the fusion zone and the adjacent heat affected zone in the two austenitic welds show that the interpretation of residual stress from strains are affected by welding parameters. An interpretation of the residual strain pattern in the ferritic steel plate can be made using the strain measurements of a Gleeble test bar which has undergone the solid state austenite decomposition.

Spooner, S.; Hubbard, C.R.; Wang, X.L.; David, S.A.; Holden, T.M. [Oak Ridge National Lab., TN (United States); Root, J.H.; Swainson, I. [Atomic Energy of Canada Ltd., Chalk River, ON (Canada)

1994-12-31T23:59:59.000Z

203

Residual Toxicities of Insecticides to Cotton Insects.  

E-Print Network [OSTI]

the effects of simulated wind and rain on the residues. Tempera- ture and humidity conditions incident to the holding period were sufficient to destroy most of the residual toxicity of this material. Effect of Simulated Wind Among the chlorinated... hydrocarbon insecticides, there was little difference between the effects of simu- lated wind and rain on residual toxicities. However, it is likely that under field conditions the effects of rain would be more noticeable. Simulated wind was less damaging...

Hightower, B. G.; Gaines, J. C.

1960-01-01T23:59:59.000Z

204

Methods of separating particulate residue streams  

DOE Patents [OSTI]

A particulate residue separator and a method for separating a particulate residue stream may include an air plenum borne by a harvesting device, and have a first, intake end and a second, exhaust end; first and second particulate residue air streams that are formed by the harvesting device and that travel, at least in part, along the air plenum and in a direction of the second, exhaust end; and a baffle assembly that is located in partially occluding relation relative to the air plenum and that substantially separates the first and second particulate residue air streams.

Hoskinson, Reed L. (Rigby, ID); Kenney, Kevin L. (Idaho Falls, ID); Wright, Christopher T. (Idaho Falls, ID); Hess, J. Richard (Idaho Falls, ID)

2011-04-05T23:59:59.000Z

205

Particulate residue separators for harvesting devices  

SciTech Connect (OSTI)

A particulate residue separator and a method for separating a particulate residue stream may include a plenum borne by a harvesting device, and have a first, intake end and a second, exhaust end; first and second particulate residue air streams which are formed by the harvesting device and which travel, at least in part, along the plenum and in a direction of the second, exhaust end; and a baffle assembly which is located in partially occluding relation relative to the plenum, and which substantially separates the first and second particulate residue air streams.

Hoskinson, Reed L.; Kenney, Kevin L.; Wright, Christopher T.; Hess, John R.

2010-06-29T23:59:59.000Z

206

Electrospray characteristic curves: in pursuit of improved performance...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Electrospray characteristic curves: in pursuit of improved performance in the nano-flow regime. Electrospray characteristic curves: in pursuit of improved performance in the...

207

Characterization Report on Sand, Slag, and Crucible Residues and on Fluoride Residues  

SciTech Connect (OSTI)

This paper reports on the chemical characterization of the sand, slag, and crucible (SS and C) residues and the fluoride residues that may be shipped from the Rocky Flats Environmental Technology Site (RFETS) to Savannah River Site (SRS).

Murray, A.M.

1999-02-10T23:59:59.000Z

208

Petroleum supply annual, 1997. Volume 1  

SciTech Connect (OSTI)

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1997 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Statistics; each with final annual data. The second volume contains final statistics for each month of 1997, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. 16 figs., 48 tabs.

NONE

1998-06-01T23:59:59.000Z

209

Petroleum supply annual 1994. Volume 1  

SciTech Connect (OSTI)

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1994 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains four sections: Summary Statistics, Detailed Statistics, Refinery Capacity, and Oxygenate Capacity each with final annual data. The second volume contains final statistics for each month of 1994, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Below is a description of each section in Volume 1 of the PSA.

NONE

1995-05-22T23:59:59.000Z

210

CONCEPTUAL DESIGN STUDY OF HORN POWER SUPPLY.  

SciTech Connect (OSTI)

A 250 kA pulsed power supply is required for the focusing horn of the proposed Brookhaven AGS Super Neutrino Beam Facility for long baseline neutrino oscillation experiment. It is expected to pulse at 2.5 Hz repetition rate. A preliminary study is being conducted to explore the key issues associated with the power supply system design. Advanced technologies used in similar systems as well as new ideas are being examined, simulated and evaluated. This power supply will be a very high stored energy, high average power, and high peak power system.

ZHANG,W.; SANDBERG,J.; WENG,W.T.

2003-06-16T23:59:59.000Z

211

Petroleum supply annual 1993. Volume 1  

SciTech Connect (OSTI)

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1993 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains four sections: Summary Statistics, Detailed Statistics, Refinery Capacity, and Oxygenate Capacity each with final annual data. The second volume contains final statistics for each month of 1993, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Below is a description of each section in Volume 1 of the PSA.

Not Available

1994-06-01T23:59:59.000Z

212

Elliptic Curves and Hyperdeterminants in Quantum Gravity  

E-Print Network [OSTI]

Hyperdeterminants are generalizations of determinants from matrices to multi-dimensional hypermatrices. They were discovered in the 19th century by Arthur Cayley but were largely ignored over a period of 100 years before once again being recognised as important in algebraic geometry, physics and number theory. It is shown that a cubic elliptic curve whose Mordell-Weil group contains a Z2 x Z2 x Z subgroup can be transformed into the degree four hyperdeterminant on a 2x2x2 hypermatrix comprising its variables and coefficients. Furthermore, a multilinear problem defined on a 2x2x2x2 hypermatrix of coefficients can be reduced to a quartic elliptic curve whose J-invariant is expressed in terms of the hypermatrix and related invariants including the degree 24 hyperdeterminant. These connections between elliptic curves and hyperdeterminants may have applications in other areas including physics.

Philip Gibbs

2010-10-20T23:59:59.000Z

213

Asymptotics for GARCH Squared Residual Correlations  

E-Print Network [OSTI]

Asymptotics for GARCH Squared Residual Correlations Istv'an Berkes \\Lambda A. R'enyi Institute a GARCH(p; q) model. Denoting by â?? r n (k); k â?? 1; these autocorrelations computed from a realization words and phrases: GARCH(p; q) sequence, quasi--maximum likelihood esti­ mator, squared residuals

Kokoszka, Piotr

214

University of Pittsburgh Residual Funds on  

E-Print Network [OSTI]

University of Pittsburgh Residual Funds on FINANCIAL GUIDELINE Subject: Sponsored Projects I by the sponsor. Funds cannot be unilaterally retained by the University. Failure to return residual funds related funds on sponsored grants and contracts on the financial accounting records of the University

Sibille, Etienne

215

Data Conversion in Residue Number System  

E-Print Network [OSTI]

for direct conversion when interaction with the real analog world is required. We first develop two efficient schemes for direct analog-to-residue conversion. Another efficient scheme for direct residue analogique réel est nécessaire. Nous dévelopons deux systèmes efficaces pour la conversion directe du domaine

Zilic, Zeljko

216

Volatile coal prices reflect supply, demand uncertainties  

SciTech Connect (OSTI)

Coal mine owners and investors say that supply and demand are now finally in balance. But coal consumers find that both spot tonnage and new contract coal come at a much higher price.

Ryan, M.

2004-12-15T23:59:59.000Z

217

Power supply noise in delay testing  

E-Print Network [OSTI]

As technology scales into the Deep Sub-Micron (DSM) regime, circuit designs have become more and more sensitive to power supply noise. Excessive noise can significantly affect the timing performance of DSM designs and cause non-trivial additional...

Wang, Jing

2009-05-15T23:59:59.000Z

218

Competitive developments in the electric supply industry  

SciTech Connect (OSTI)

Competition in the electric supply industry is outlined. The following topics are discussed: six impending major developments in the electric industry; recent and projected developments in the industry; where is the industry headed?; and what the future holds.

Bruder, G.F.; Lively, M.

1996-12-31T23:59:59.000Z

219

The supply chain response to environmental pressures  

E-Print Network [OSTI]

Understanding and shaping the relationship between supply chain management and the natural environment is critical not only to human health and the environment, but to the future success of business. While the cumulative ...

Paquette, Julie Rebecca

2006-01-01T23:59:59.000Z

220

Internal Markets for Supply Chain Capacity Allocation  

E-Print Network [OSTI]

This paper explores the possibility of solving supply chain capacity allocation problems using internal markets among employees of the same company. Unlike earlier forms of transfer pricing, IT now makes it easier for such ...

McAdams, David

2005-07-08T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Supplies Needed Polyester Fleece (13" x 23")  

E-Print Network [OSTI]

Supplies Needed Polyester Fleece (13" x 23") Polyester Thread This one is easy. Really easy inclined, add a drawstring to the top and it will double as a hat. Pretty cool, eh? Texas 4-H Clothing

222

Global supply chain design and optimization methodology  

E-Print Network [OSTI]

The work for this thesis was performed at Honeywell in the Automation and Control Solutions (ACS) division. The project focuses on ACS's manufacturing strategy regarding its global supply chain design, primarily discussing ...

Henkle, Aimee L. (Aimee Leigh), 1975-

2004-01-01T23:59:59.000Z

223

Economic analysis of the meat supply chain  

E-Print Network [OSTI]

and overseas animal disease outbreaks on the Korean meat supply chain. Market impacts are investigated using both forecasts and historical decomposition of price innovations based on an error correction model (ECM) of the Korean meat sector. Results indicate...

Park, Moon-Soo

2009-05-15T23:59:59.000Z

224

Supply chain and the executive agenda  

E-Print Network [OSTI]

In recent years, supply chain pundits and consultants emphasized the importance of strategies such as just-in-time, lean manufacturing, off- shoring or frequent deliveries to retail outlets. However, with significant ...

Peruvankal, James Paul

2011-01-01T23:59:59.000Z

225

Essays on Married Women Labor Supply  

E-Print Network [OSTI]

One of the very interesting demographic features in the US over the last three decades of the 20th century is the increase of the married women labor force participation rate. Over the same period, estimated labor supply elasticity varies...

Li, Xinrong

2012-02-14T23:59:59.000Z

226

Segmentation strategies for managing retail supply chains  

E-Print Network [OSTI]

High-technology manufacturing companies often face rapid price decline and capacity constraints. Especially in the retail side of the business where the supply chain is much longer and revenue is sometimes not recognized ...

Liang, Catherine G. (Catherine Gloria)

2011-01-01T23:59:59.000Z

227

Advanced Supply System Validation Workshop Agenda  

Broader source: Energy.gov [DOE]

List of Assumptions and Draft Workshop Agenda for the Advanced Supply System Validation Workshop, February 3-4, 2014, Golden, Colorado, from the U.S. Department of Energy's Bioenergy Technologies Office.

228

Global Energy: Supply, Demand, Consequences, Opportunities  

ScienceCinema (OSTI)

July 29, 2008 Berkeley Lab lecture: Arun Majumdar, Director of the Environmental Energy Technologies Division, discusses current and future projections of economic growth, population, and global energy demand and supply, and explores the implications of these trends for the environment.

Arun Majumdar

2010-01-08T23:59:59.000Z

229

Petroleum Supply Annual 2005, Volume 1  

Gasoline and Diesel Fuel Update (EIA)

Table 2. U.S. Daily Average Supply and Disposition of Crude Oil and Petroleum Products, 2005 (Thousand Barrels per Day) Field Production Refinery and Blender Net Production Imports...

230

CLIMATE CHANGE AND WATER SUPPLY SECURITY  

E-Print Network [OSTI]

CLIMATE CHANGE AND WATER SUPPLY SECURITY: Reconfiguring Groundwater Management to Reduce with climate change, present a significant planning challenge for California's water agencies. This research Drought Vulnerability A White Paper from the California Energy Commission's California Climate

231

An analysis of oil supply disruption scenarios  

E-Print Network [OSTI]

This report brings the results of simulations of some oil supply disruptions on the M.I.T. Energy Laboratory Energy Macro Model. This model has previously been used to study the macroeconomic effects of the 1973-74 and ...

Mork, Knut Anton

1981-01-01T23:59:59.000Z

232

Customer service driven supply chain segmentation  

E-Print Network [OSTI]

The objective of this thesis is to develop a supply chain segmentation model for Company X, which is in the chemical and construction materials industry. The company sells products in an expanding Southeast Asia market. ...

Worawattananon, Prakit

2008-01-01T23:59:59.000Z

233

RECYCLING: SUPPLY, ECONOMICS, ENVIRONMENT, AND TECHNOLOGY  

E-Print Network [OSTI]

RECYCLING: SUPPLY, ECONOMICS, ENVIRONMENT, AND TECHNOLOGY Panel Discussion Roundtable Moderator: S, although higher market values for recyclable will certainly stimulate increased interest in collection in recycling and deinking technologies and process design among North American, European, and Pacific Rim

Abubakr, Said

234

Supply chain practices in the petroleum downstream  

E-Print Network [OSTI]

This thesis studies current supply chain practices in the petroleum downstream industry, using ExxonMobil as a case study. Based on the analysis of the literature and the interaction with industry experts, this work describes ...

Santos Manzano, Fidel

2005-01-01T23:59:59.000Z

235

Polynomial policies in supply chain networks  

E-Print Network [OSTI]

This thesis aims to solve the periodic-reviewed inventory control problem in supply chain networks with uncertain demand so as to minimize the overall cost of the system over a fixed planning time horizon. In such problems, ...

He, Liwei

2010-01-01T23:59:59.000Z

236

Risk in the Global Supply Chain  

E-Print Network [OSTI]

Carbon footprints are not on the priority list of risk analysts in operations management for at least half or more of global businesses. What are the other risks in the global supply chain?

Datta, Shoumen

2006-01-01T23:59:59.000Z

237

A single power supply optoelectronic differential amplifier  

E-Print Network [OSTI]

A SINGLE POWER SUPPLY OPTOELECTRONIC DIFFERENTIAL AMPLIFIER A Thesis by YOUNGiXIIN ALBERT CHOI Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCE December... 1987 Major Subject: Electrical Engineering A SINGLE POWER SUPPLY OPTOELECTRONIC DIFFERENTIAL AMPLIFIER A Thesis by YOUNGMIN ALBERT CHOI Approved a. s to style and content by: He y F. aylor (Chairman of Committee) Kai Chang (Member) Ohannes...

Choi, Youngmin Albert

1987-01-01T23:59:59.000Z

238

Seasonal demand and supply analysis of turkeys  

E-Print Network [OSTI]

SEASONAL DEMAND AND SUPPLY ANALYSIS OF TURKEYS A Thesis by VITO JAMES BLOMO Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCE May 1972 Ma)or Sub...)ect: Agricultural Economics SEASONAL DEMAND AND SUPPLY ANALYSIS OF TURKEYS A Thesis by VITO JAMES BLOMO Approved as to style and content by: (Chairman of C mmittee) (Head of Department) (Member) (Member) ( ber) (Memb er) May 1972 ABSTRACT Seasonal...

Blomo, Vito James

1972-01-01T23:59:59.000Z

239

Integrated Planning and Management for Urban Water Supplies  

E-Print Network [OSTI]

Positions for Water Supply Reliability ................................. 15 4 Shortage Management Modeling.2: Diagram of Water Supply Reliability Model Structure ..................49 5.3: Steps Used in ShortageIntegrated Planning and Management for Urban Water Supplies Considering Multiple Uncertainties Jay

Pasternack, Gregory B.

240

Impact of demographics on supply chain risk management practices  

E-Print Network [OSTI]

Do demographic factors play a role in the choice of supply chain risk management practices by supply chain professionals? Are there stronger relationships between certain demographic factors and supply chain risk management ...

Kanyagui, Kenneth (Kenneth K.)

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Dynamic Electric Power Supply Chains and Transportation Networks  

E-Print Network [OSTI]

Dynamic Electric Power Supply Chains and Transportation Networks: an Evolutionary Variational energy Electric power supply chains, provide the foundations for theElectric power supply chains, provide and societies. Communication, transportation, heating, lighting, cooling,Communication, transportation, heating

Nagurney, Anna

242

Air Handling Unit Supply Air Temperature Optimization During Economizer Cycles  

E-Print Network [OSTI]

temperature at supply air temperature setpoint. Mechanical cooling is always required when outside air temperature is higher than the supply air temperature setpoint. Generally the supply air temperature setpoint is set at 55°F for space humidity control...

Xu, K.; Liu, M.; Wang, G.; Wang, Z.

2007-01-01T23:59:59.000Z

243

An engineering approach to improving hospital supply chains  

E-Print Network [OSTI]

This thesis explores supply chain management practices that have been implemented, and have improved supply chains in industries outside of healthcare. The presented supply chain practices have been selected because they ...

Cheng, Scott Hsiang-Jen

2008-01-01T23:59:59.000Z

244

Geodesic Bezier Curves on Triangle Meshes Dimas Martinez Morera  

E-Print Network [OSTI]

Geodesic B´ezier Curves on Triangle Meshes Dimas Mart´inez Morera IMPA - Brazil / ICIMAF - Cuba generalization of B´ezier curves. Thus, we call them "Geodesic B´ezier Curves". Geodesic B´ezier curves, but geodesics connecting the control points. This imposes the necessity of modifying the inter- polation step

245

Research Summary Estimating Woodfuel Resource Cost Curves  

E-Print Network [OSTI]

Research Summary Estimating Woodfuel Resource Cost Curves As a renewable energy source, woodfuel and extraction methods. Background Just under half of the final energy consumed in the UK (49%) is in the form working slope for the chosen type of machinery) and soil conditions (risk of soil damage). Note

246

The Elliptic Curve Digital Signature Algorithm (ECDSA)  

E-Print Network [OSTI]

). It was accepted in 1999 as an ANSI standard, and was accepted in 2000 as IEEE and NIST standards. It was also-per-key-bit is substantially greater in an algorithm that uses elliptic curves. This paper describes the ANSI X9.62 ECDSA Standards Organization) standard (ISO 14888-3), accepted in 1999 as an ANSI (American National Standards

247

Closed timelike curves in general relativity  

E-Print Network [OSTI]

Many solutions of Einstein's field equations contain closed timelike curves (CTC). Some of these solutions refer to ordinary materials in situations which might occur in the laboratory, or in astrophysics. It is argued that, in default of a reasonable interpretation of CTC, general relativity does not give a satisfactory account of all phenomena within its terms of reference.

W. B. Bonnor

2002-11-13T23:59:59.000Z

248

WILD MODELS OF CURVES DINO LORENZINI  

E-Print Network [OSTI]

WILD MODELS OF CURVES DINO LORENZINI Abstract. Let K be a complete discrete valuation field of X/K obtained by desingularizing the wild quotient singularities of the quotient Y/H. The most of wild quotient singularities having pairwise distinct resolution graphs. The information on the regular

Lorenzini, Dino J.

249

ADMINISTRATIVE RECORDS SCHEDULE 3: PROCUREMENT, SUPPLY, AND GRANT...  

Energy Savers [EERE]

RECORDS SCHEDULE 3: PROCUREMENT, SUPPLY, AND GRANT RECORDS ADMINISTRATIVE RECORDS SCHEDULE 3: PROCUREMENT, SUPPLY, AND GRANT RECORDS The basic procurement files reflect a...

250

ADMINISTRATIVE RECORDS SCHEDULE 3: PROCUREMENT, SUPPLY, AND GRANT...  

Office of Environmental Management (EM)

ADMINISTRATIVE RECORDS SCHEDULE 3: PROCUREMENT, SUPPLY, AND GRANT RECORDS ADMINISTRATIVE RECORDS SCHEDULE 3: PROCUREMENT, SUPPLY, AND GRANT RECORDS The basic procurement files...

251

EO 13211: Regulations That Significantly Affect Energy Supply...  

Energy Savers [EERE]

1: Regulations That Significantly Affect Energy Supply, Distribution, or Use EO 13211: Regulations That Significantly Affect Energy Supply, Distribution, or Use I am requiring that...

252

Engine Driven Combined Heat and Power: Arrow Linen Supply, December...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Engine Driven Combined Heat and Power: Arrow Linen Supply, December 2008 Engine Driven Combined Heat and Power: Arrow Linen Supply, December 2008 This paper describes the Arrow...

253

Advanced Supply System Validation Workshop | Department of Energy  

Office of Environmental Management (EM)

of biomass to biorefineries annually Advanced supply system concepts, including depots Business models for advanced supply systems Siting and sizing considerations for depots...

254

Steel Success Story - Ironmaking: Quality and Supply Critical...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Steel Success Story - Ironmaking: Quality and Supply Critical to Steel Industry Steel Success Story - Ironmaking: Quality and Supply Critical to Steel Industry This factsheet...

255

Energy Department Announces $2 Million to Develop Supply Chain...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

2 Million to Develop Supply Chain, Manufacturing Competitiveness Analysis for Hydrogen and Fuel Cell Technologies Energy Department Announces 2 Million to Develop Supply Chain,...

256

Hydrogen Supply: Cost Estimate for Hydrogen Pathways-Scoping...  

Broader source: Energy.gov (indexed) [DOE]

Supply: Cost Estimate for Hydrogen Pathways-Scoping Analysis. January 22, 2002-July 22, 2002 Hydrogen Supply: Cost Estimate for Hydrogen Pathways-Scoping Analysis. January 22,...

257

MODEL BASED BIOMASS SYSTEM DESIGN OF FEEDSTOCK SUPPLY SYSTEMS FOR BIOENERGY PRODUCTION  

SciTech Connect (OSTI)

Engineering feedstock supply systems that deliver affordable, high-quality biomass remains a challenge for the emerging bioenergy industry. Cellulosic biomass is geographically distributed and has diverse physical and chemical properties. Because of this feedstock supply systems that deliver cellulosic biomass resources to biorefineries require integration of a broad set of engineered unit operations. These unit operations include harvest and collection, storage, preprocessing, and transportation processes. Design decisions for each feedstock supply system unit operation impact the engineering design and performance of the other system elements. These interdependencies are further complicated by spatial and temporal variances such as climate conditions and biomass characteristics. This paper develops an integrated model that couples a SQL-based data management engine and systems dynamics models to design and evaluate biomass feedstock supply systems. The integrated model, called the Biomass Logistics Model (BLM), includes a suite of databases that provide 1) engineering performance data for hundreds of equipment systems, 2) spatially explicit labor cost datasets, and 3) local tax and regulation data. The BLM analytic engine is built in the systems dynamics software package PowersimTM. The BLM is designed to work with thermochemical and biochemical based biofuel conversion platforms and accommodates a range of cellulosic biomass types (i.e., herbaceous residues, short- rotation woody and herbaceous energy crops, woody residues, algae, etc.). The BLM simulates the flow of biomass through the entire supply chain, tracking changes in feedstock characteristics (i.e., moisture content, dry matter, ash content, and dry bulk density) as influenced by the various operations in the supply chain. By accounting for all of the equipment that comes into contact with biomass from the point of harvest to the throat of the conversion facility and the change in characteristics, the BLM evaluates economic performance of the engineered system, as well as determining energy consumption and green house gas performance of the design. This paper presents a BLM case study delivering corn stover to produce cellulosic ethanol. The case study utilizes the BLM to model the performance of several feedstock supply system designs. The case study also explores the impact of temporal variations in climate conditions to test the sensitivity of the engineering designs. Results from the case study show that under certain conditions corn stover can be delivered to the cellulosic ethanol biorefinery for $35/dry ton.

David J. Muth, Jr.; Jacob J. Jacobson; Kenneth M. Bryden

2013-08-01T23:59:59.000Z

258

Development of the Integrated Biomass Supply Analysis and Logistics Model (IBSAL)  

SciTech Connect (OSTI)

The Integrated Biomass Supply & Logistics (IBSAL) model is a dynamic (time dependent) model of operations that involve collection, harvest, storage, preprocessing, and transportation of feedstock for use at a biorefinery. The model uses mathematical equations to represent individual unit operations. These unit operations can be assembled by the user to represent the working rate of equipment and queues to represent storage at facilities. The model calculates itemized costs, energy input, and carbon emissions. It estimates resource requirements and operational characteristics of the entire supply infrastructure. Weather plays an important role in biomass management and thus in IBSAL, dictating the moisture content of biomass and whether or not it can be harvested on a given day. The model calculates net biomass yield based on a soil conservation allowance (for crop residue) and dry matter losses during harvest and storage. This publication outlines the development of the model and provides examples of corn stover harvest and logistics.

Sokhansanj, Shahabaddine [ORNL; Webb, Erin [ORNL; Turhollow Jr, Anthony F [ORNL

2008-06-01T23:59:59.000Z

259

Residual stress in nanocrystalline nickel tungsten electrodeposits  

E-Print Network [OSTI]

Characterizing the residual stress of thick nanocrystalline electrodeposits poses several unique challenges due to their fine grain structure, thickness distribution, and matte surface. We employ a three-dimensional ...

Ziebell, Tiffany D. (Tiffany Dawn)

2011-01-01T23:59:59.000Z

260

SAR impulse response with residual chirps.  

SciTech Connect (OSTI)

A Linear Frequency-Modulated (LFM) chirp is a function with unit amplitude and quadratic phase characteristic. In a focused Synthetic Aperture Radar (SAR) image, a residual chirp is undesired for targets of interest, as it coarsens the manifested resolution. However, for undesired spurious signals, a residual chirp is often advantageous because it spreads the energy and thereby diminishes its peak value. In either case, a good understanding of the effects of a residual LFM chirp on a SAR Impulse Response (IPR) is required to facilitate system analysis and design. This report presents an analysis of the effects of a residual chirp on the IPR. As reference, there is a rich body of publications on various aspects of LFM chirps. A quick search reveals a plethora of articles, going back to the early 1950s. We mention here purely as trivia one of the earlier analysis papers on this waveform by Klauder, et al.

Doerry, Armin Walter

2009-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

International Oil Supplies and Demands. Volume 1  

SciTech Connect (OSTI)

The eleventh Energy Modeling Forum (EMF) working group met four times over the 1989--90 period to compare alternative perspectives on international oil supplies and demands through 2010 and to discuss how alternative supply and demand trends influence the world`s dependence upon Middle Eastern oil. Proprietors of eleven economic models of the world oil market used their respective models to simulate a dozen scenarios using standardized assumptions. From its inception, the study was not designed to focus on the short-run impacts of disruptions on oil markets. Nor did the working group attempt to provide a forecast or just a single view of the likely future path for oil prices. The model results guided the group`s thinking about many important longer-run market relationships and helped to identify differences of opinion about future oil supplies, demands, and dependence.

Not Available

1991-09-01T23:59:59.000Z

262

Petroleum supply annual, 1997. Volume 2  

SciTech Connect (OSTI)

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1997 through monthly surveys. The PSA is divided into two volumes. The first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Statistics; each with final annual data. The second volume contains final statistics for each month of 1997, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary. 35 tabs.

NONE

1998-06-01T23:59:59.000Z

263

Petroleum supply annual 1995: Volume 2  

SciTech Connect (OSTI)

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1995 through monthly surveys. The PSA is divided into two volumes. This first volume contains three sections: Summary Statistics, Detailed Statistics, and selected Refinery Statistics each with final annual data. The second volume contains final statistics for each month of 1995, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary.

NONE

1996-06-01T23:59:59.000Z

264

Petroleum supply annual 1996: Volume 2  

SciTech Connect (OSTI)

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1996 through monthly surveys. The PSA is divided into two volumes. The first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Capacity; each with final annual data. The second volume contains final statistics for each month of 1996, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary. 35 tabs.

NONE

1997-06-01T23:59:59.000Z

265

Petroleum supply annual 1998: Volume 2  

SciTech Connect (OSTI)

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1998 through monthly surveys. The PSA is divided into two volumes. The first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Statistics; each with final annual data. This second volume contains final statistics for each month of 1998, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary. 35 tabs.

NONE

1999-06-01T23:59:59.000Z

266

Petroleum supply annual 1994, Volume 2  

SciTech Connect (OSTI)

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1994 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains four sections: Summary Statistics, Detailed Statistics, Refinery Capacity, and Oxygenate Capacity each with final annual data. The second volume contains final statistics for each month of 1994, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary.

NONE

1995-06-01T23:59:59.000Z

267

International Oil Supplies and Demands. Volume 2  

SciTech Connect (OSTI)

The eleventh Energy Modeling Forum (EMF) working group met four times over the 1989--1990 period to compare alternative perspectives on international oil supplies and demands through 2010 and to discuss how alternative supply and demand trends influence the world`s dependence upon Middle Eastern oil. Proprietors of eleven economic models of the world oil market used their respective models to simulate a dozen scenarios using standardized assumptions. From its inception, the study was not designed to focus on the short-run impacts of disruptions on oil markets. Nor did the working group attempt to provide a forecast or just a single view of the likely future path for oil prices. The model results guided the group`s thinking about many important longer-run market relationships and helped to identify differences of opinion about future oil supplies, demands, and dependence.

Not Available

1992-04-01T23:59:59.000Z

268

Curved butterfly bileaflet prosthetic cardiac valve  

DOE Patents [OSTI]

An annular valve body having a central passageway for the flow of blood therethrough with two curved leaflets each of which is pivotally supported on an accentric positioned axis in the central passageway for moving between a closed position and an open position. The leaflets are curved in a plane normal to the eccentric axis and positioned with the convex side of the leaflets facing each other when the leaflets are in the open position. Various parameters such as the curvature of the leaflets, the location of the eccentric axis, and the maximum opening angle of the leaflets are optimized according to the following performance criteria: maximize the minimum peak velocity through the valve, maximize the net stroke volume, and minimize the mean forward pressure difference, thereby reducing thrombosis and improving the hemodynamic performance.

McQueen, David M. (185 Hillside Ave., Chatham, NJ 07928); Peskin, Charles S. (186 Harrard Dr., Hartsdale, NY 10530)

1991-06-25T23:59:59.000Z

269

Petroleum supply annual 1998: Volume 1  

SciTech Connect (OSTI)

The ``Petroleum Supply Annual`` (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1998 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Statistics; each with final annual data. The second volume contains final statistics for each month of 1998, and replaces data previously published in the PSA. The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. 16 figs., 59 tabs.

NONE

1999-06-01T23:59:59.000Z

270

Updated U.S. Geothermal Supply Characterization  

SciTech Connect (OSTI)

This paper documents the approach taken to characterize and represent an updated assessment of U.S. geothermal supply for use in forecasting the penetration of geothermal electrical generation in the National Energy Modeling System (NEMS). This work is motivated by several factors: The supply characterization used as the basis of several recent U.S. Department of Energy (DOE) forecasts of geothermal capacity is outdated; additional geothermal resource assessments have been published; and a new costing tool that incorporates current technology, engineering practices, and associated costs has been released.

Petty, S.; Porro, G.

2007-03-01T23:59:59.000Z

271

Supplying High-Quality, Raw Biomass  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas ConchasPassiveSubmittedStatus TomAbout »Lab (NewportSuccessSupply Stores Supply Stores

272

Supplying success | Y-12 National Security Complex  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas ConchasPassiveSubmittedStatus TomAbout »Lab (NewportSuccessSupply Stores Supply

273

Galaxy rotation curves in de Sitter space  

E-Print Network [OSTI]

Dark energy inferred from the observed negative deceleration parameter introduces a small mass of the graviton, that satisfies the Higuchi stability condition. It implies an infra-red modification of gravitation that produces Milgrom's inverse distance law of gravitational attraction in excellent agreement with the observed galaxy rotation curves. We conclude that dark matter is present cosmologically with no need for local clustering in galaxies.

Maurice H. P. M. van Putten

2015-01-27T23:59:59.000Z

274

Light Curves of Swift Gamma Ray Bursts  

E-Print Network [OSTI]

Recent observations from the Swift gamma-ray burst mission indicate that a fraction of gamma ray bursts are characterized by a canonical behaviour of the X-ray afterglows. We present an effective theory which allows us to account for X-ray light curves of both (short - long) gamma ray bursts and X-ray rich flashes. We propose that gamma ray bursts originate from massive magnetic powered pulsars.

Paolo Cea

2006-09-22T23:59:59.000Z

275

Evaluate Supply and Recovery of Woody Biomass for Energy  

E-Print Network [OSTI]

Biomass Recovery DataContrasting Woody Biomass Recovery Data Forest Biomass Supply in the Southeastern4/11/2011 1 Evaluate Supply and Recovery of Woody Biomass for Energy Production from Natural. Other studies of biomass supply have supply have assumedassumed a technical recovery rate

Gray, Matthew

276

A Supply Chain Generalized Network Oligopoly Model for Pharmaceuticals  

E-Print Network [OSTI]

dollars in drugs, vaccines, and other medical supplies were found spoiled, stolen, or unaccounted for

Nagurney, Anna

277

The Rise and Fall of Type Ia Supernova Light Curves in the SDSS-II Supernova Survey  

SciTech Connect (OSTI)

We analyze the rise and fall times of Type Ia supernova (SN Ia) light curves discovered by the Sloan Digital Sky Survey-II (SDSS-II) Supernova Survey. From a set of 391 light curves k-corrected to the rest-frame B and V bands, we find a smaller dispersion in the rising portion of the light curve compared to the decline. This is in qualitative agreement with computer models which predict that variations in radioactive nickel yield have less impact on the rise than on the spread of the decline rates. The differences we find in the rise and fall properties suggest that a single 'stretch' correction to the light curve phase does not properly model the range of SN Ia light curve shapes. We select a subset of 105 light curves well observed in both rise and fall portions of the light curves and develop a '2-stretch' fit algorithm which estimates the rise and fall times independently. We find the average time from explosion to B-band peak brightness is 17.38 {+-} 0.17 days, but with a spread of rise times which range from 13 days to 23 days. Our average rise time is shorter than the 19.5 days found in previous studies; this reflects both the different light curve template used and the application of the 2-stretch algorithm. The SDSS-II supernova set and the local SNe Ia with well-observed early light curves show no significant differences in their average rise-time properties. We find that slow-declining events tend to have fast rise times, but that the distribution of rise minus fall time is broad and single peaked. This distribution is in contrast to the bimodality in this parameter that was first suggested by Strovink (2007) from an analysis of a small set of local SNe Ia. We divide the SDSS-II sample in half based on the rise minus fall value, t{sub r} - t{sub f} {approx}< 2 days and t{sub r} - t{sub f} > 2 days, to search for differences in their host galaxy properties and Hubble residuals; we find no difference in host galaxy properties or Hubble residuals in our sample.

Hayden, Brian T.; /Notre Dame U.; Garnavich, Peter M.; /Notre Dame U.; Kessler, Richard; /KICP, Chicago /Chicago U., EFI; Frieman, Joshua A.; /KICP, Chicago /Chicago U. /Fermilab; Jha, Saurabh W.; /Stanford U., Phys. Dept. /Rutgers U., Piscataway; Bassett, Bruce; /Cape Town U., Dept. Math. /South African Astron. Observ.; Cinabro, David; /Wayne State U.; Dilday, Benjamin; /Rutgers U., Piscataway; Kasen, Daniel; /UC, Santa Cruz; Marriner, John; /Fermilab; Nichol, Robert C.; /Portsmouth U., ICG /Baltimore, Space Telescope Sci. /Johns Hopkins U.

2010-01-01T23:59:59.000Z

278

Particle transport in turbulent curved pipe flow  

E-Print Network [OSTI]

Direct numerical simulations (DNS) of particle-laden turbulent flow in straight, mildly curved and strongly bent pipes are performed in which the solid phase is modelled as small heavy spherical particles. The objective is to examine the effect of the curvature on particle transport and accumulation, in particular how the turbophoretic drift of the particles is affected by weak and strong secondary motions of the carrier phase and geometry-induced centrifugal forces. A total of seven populations of dilute particles with different Stokes numbers, one-way coupled with their carrier phase, are simulated. Even a slight non-zero curvature in the flow configuration shows a strong impact on the particle dynamics. Near-wall helicoidal particle streaks are observed in the curved configurations with their inclination varying with the strength of the secondary motion of the carrier phase. A reflection layer, as previously observed in particle laden turbulent S-shaped channels, is also apparent in the strongly curved pip...

Noorani, Azad; Brandt, Luca; Schlatter, Philipp

2015-01-01T23:59:59.000Z

279

Rotation Curve Measurement using Cross-Correlation  

E-Print Network [OSTI]

Longslit spectroscopy is entering an era of increased spatial and spectral resolution and increased sample size. Improved instruments reveal complex velocity structure that cannot be described with a one-dimensional rotation curve, yet samples are too numerous to examine each galaxy in detail. Therefore, one goal of rotation curve measurement techniques is to flag cases in which the kinematic structure of the galaxy is more complex than a single-valued curve. We examine cross-correlation as a technique that is easily automated and works for low signal-to-noise spectra. We show that the technique yields well-defined errors which increase when the simple spectral model (template) is a poor match to the data, flagging those cases for later inspection. We compare the technique to the more traditional, parametric technique of simultaneous emission line fitting. When the line profile at a single slit position is non-Gaussian, the techniques disagree. For our model spectra with two well-separated velocity components, assigned velocities from the two techniques differ by up to ~52% of the velocity separation of the model components. However, careful use of the error statistics for either technique allows one to flag these non-Gaussian spectra.

Elizabeth J. Barton; Sheila J. Kannappan; Michael J. Kurtz; Margaret J. Geller

2000-06-20T23:59:59.000Z

280

Incorporating Experience Curves in Appliance Standards Analysis  

SciTech Connect (OSTI)

The technical analyses in support of U.S. energy conservation standards for residential appliances and commercial equipment have typically assumed that manufacturing costs and retail prices remain constant during the projected 30-year analysis period. There is, however, considerable evidence that this assumption does not reflect real market prices. Costs and prices generally fall in relation to cumulative production, a phenomenon known as experience and modeled by a fairly robust empirical experience curve. Using price data from the Bureau of Labor Statistics, and shipment data obtained as part of the standards analysis process, we present U.S. experience curves for room air conditioners, clothes dryers, central air conditioners, furnaces, and refrigerators and freezers. These allow us to develop more representative appliance price projections than the assumption-based approach of constant prices. These experience curves were incorporated into recent energy conservation standards for these products. The impact on the national modeling can be significant, often increasing the net present value of potential standard levels in the analysis. In some cases a previously cost-negative potential standard level demonstrates a benefit when incorporating experience. These results imply that past energy conservation standards analyses may have undervalued the economic benefits of potential standard levels.

Garbesi, Karina; Chan, Peter; Greenblatt, Jeffery; Kantner, Colleen; Lekov, Alex; Meyers, Stephen; Rosenquist, Gregory; Buskirk, Robert Van; Yang, Hung-Chia; Desroches, Louis-Benoit

2011-10-31T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Sustainable System for Residual Hazards Management  

SciTech Connect (OSTI)

Hazardous, radioactive and other toxic substances have routinely been generated and subsequently disposed of in the shallow subsurface throughout the world. Many of today’s waste management techniques do not eliminate the problem, but rather only concentrate or contain the hazardous contaminants. Residual hazards result from the presence of hazardous and/or contaminated material that remains on-site following active operations or the completion of remedial actions. Residual hazards pose continued risk to humans and the environment and represent a significant and chronic problem that require continuous longterm management (i.e. >1000 years). To protect human health and safeguard the natural environment, a sustainable system is required for the proper management of residual hazards. A sustainable system for the management of residual hazards will require the integration of engineered, institutional and land-use controls to isolate residual contaminants and thus minimize the associated hazards. Engineered controls are physical modifications to the natural setting and ecosystem, including the site, facility, and/or the residual materials themselves, in order to reduce or eliminate the potential for exposure to contaminants of concern (COCs). Institutional controls are processes, instruments, and mechanisms designed to influence human behavior and activity. System failure can involve hazardous material escaping from the confinement because of system degradation (i.e., chronic or acute degradation) or by externalintrusion of the biosphere into the contaminated material because of the loss of institutional control. An ongoing analysis of contemporary and historic sites suggests that the significance of the loss of institutional controls is a critical pathway because decisions made during the operations/remedial action phase, as well as decisions made throughout the residual hazards management period, are key to the longterm success of the prescribed system. In fact, given that society has become more reliant on and confident of engineered controls, there may be a growing tendency to be even less concerned with institutional controls.

Kevin M. Kostelnik; James H. Clarke; Jerry L. Harbour

2004-06-01T23:59:59.000Z

282

Petroleum supply annual 1993. Volume 2  

SciTech Connect (OSTI)

This publication contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1993 through annual and monthly surveys. This second volume contains final statistics for each month of 1993.

Not Available

1994-06-01T23:59:59.000Z

283

Fashion Supply Chain Network Competition Ecolabelling  

E-Print Network [OSTI]

, Gothenburg, Sweden 3 Pamplin School of Business Administration University of Portland Portland, Oregon 97203 April 2014; revised June 2014 To appear in Sustainable Fashion Supply Chain Management: From Sourcing, energy, as well as chemicals. For example, it is estimated that cotton uses only 3% of the world

Nagurney, Anna

284

Supply Chain Networks: Challenges and Opportunities  

E-Print Network [OSTI]

School of Management University of Massachusetts Amherst, Massachusetts 01003 Boston INFORMS Chapter and suppliers, distributors, retailers, and consumers at the demand markets. Today, supply chains may span chains, as well as their adaptability and responsiveness to events in a global environment of increasing

Nagurney, Anna

285

Supply Chain Networks: Challenges and Opportunities  

E-Print Network [OSTI]

School of Management University of Massachusetts Amherst, Massachusetts 01003 International Conference of manufacturers and suppliers, distributors, retailers, and consumers at the demand markets. Today, supply chains chains, as well as their adaptability and responsiveness to events in a global environment of increasing

Nagurney, Anna

286

Solar Supply Chain and Market Driver Analysis  

E-Print Network [OSTI]

This study aims to explore the evolution of the photovoltaic supply chain in the United States and the drivers which foster growth of the solar market. The study will gather knowledge on the growth of the solar market and roles of different firms...

Martinez, Nicholas 1990-

2012-05-09T23:59:59.000Z

287

A methodology for estimating the residual contamination contribution to the source term in a spent-fuel transport cask  

SciTech Connect (OSTI)

This report describes the ranges of the residual contamination that may build up in spent-fuel transport casks. These contamination ranges are calculated based on data taken from published reports and from previously unpublished data supplied by cask transporters. The data involve dose rate measurements, interior smear surveys, and analyses of water flushed out of cask cavities during decontamination operations. A methodology has been developed to estimate the effect of residual contamination on spent-fuel cask containment requirements. Factors in estimating the maximum permissible leak rates include the form of the residual contamination; possible release modes; internal gas-borne depletion; and the temperature, pressure, and vibration characteristics of the cask during transport under normal and accident conditions. 12 refs., 9 figs., 4 tabs.

Sanders, T.L. (Sandia National Labs., Albuquerque, NM (United States)); Jordan, H. (EG and G Rocky Flats, Inc., Golden, CO (United States). Rocky Flats Plant); Pasupathi, V. (Battelle, Columbus, OH (United States)); Mings, W.J. (USDOE Idaho Field Office, Idaho Falls, ID (United States)); Reardon, P.C. (GRAM, Inc., Albuquerque, NM (United States))

1991-09-01T23:59:59.000Z

288

Application of NUREG/CR-5999 interim fatigue curves to selected nuclear power plant components  

SciTech Connect (OSTI)

Recent test data indicate that the effects of the light water reactor (LWR) environment could significantly reduce the fatigue resistance of materials used in the reactor coolant pressure boundary components of operating nuclear power plants. Argonne National Laboratory has developed interim fatigue curves based on test data simulating LWR conditions, and published them in NUREG/CR-5999. In order to assess the significance of these interim fatigue curves, fatigue evaluations of a sample of the components in the reactor coolant pressure boundary of LWRs were performed. The sample consists of components from facilities designed by each of the four U.S. nuclear steam supply system vendors. For each facility, six locations were studied, including two locations on the reactor pressure vessel. In addition, there are older vintage plants where components of the reactor coolant pressure boundary were designed to codes that did not require an explicit fatigue analysis of the components. In order to assess the fatigue resistance of the older vintage plants, an evaluation was also conducted on selected components of three of these plants. This report discusses the insights gained from the application of the interim fatigue curves to components of seven operating nuclear power plants.

Ware, A.G.; Morton, D.K.; Nitzel, M.E. [Idaho National Engineering Lab., Idaho Falls, ID (United States)

1995-03-01T23:59:59.000Z

289

Modeling software artifact count attribute with s-curves  

E-Print Network [OSTI]

????????.???????. 44 16 Linear graph of various intercept parameter values ????????... 45 17 S-curves with various generator parameter values ?????????. 46 18 Linear fit with various generator parameter values ????????? 47 19 S-curve with various expected maximum... Artifact Graph (NPAG) Format ????.. 34 D. S-curve and Straight Line Description .......................................... 41 1. The Readiness Parameter ?????????????. 44 2. The Generation Parameter ????????????? 46 3. The S-curve Constant...

Ma, Norman K.

2009-05-15T23:59:59.000Z

290

Modeling software artifact count attribute with s-curves  

E-Print Network [OSTI]

…………………….…………………. 44 16 Linear graph of various intercept parameter values ……………………... 45 17 S-curves with various generator parameter values ………………………. 46 18 Linear fit with various generator parameter values ……………………… 47 19 S-curve with various expected maximum... Artifact Graph (NPAG) Format ………….. 34 D. S-curve and Straight Line Description .......................................... 41 1. The Readiness Parameter …………………………………. 44 2. The Generation Parameter ………………………………… 46 3. The S-curve Constant...

Ma, Norman K

2008-10-10T23:59:59.000Z

291

BY HOW MUCH CAN RESIDUAL MINIMIZATION ACCELERATE THE CONVERGENCE OF ORTHOGONAL RESIDUAL METHODS?  

E-Print Network [OSTI]

. Examples of such pairs are the conjugate gradient (CG) and the conjugate residual (CR) methods, the full-minimal residual (QMR) methods. Also the pairs consisting of the (bi)conjugate gradient squared (CGS, iterative method, Krylov space method, conjugate gradient method, biconjugate gradient method, CG, CGNE

Gutknecht, Martin H.

292

E-Print Network 3.0 - alternative energy supplies Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

supplies Search Powered by Explorit Topic List Advanced Search Sample search results for: alternative energy supplies...

293

E-Print Network 3.0 - alternative energy supply Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

supply Search Powered by Explorit Topic List Advanced Search Sample search results for: alternative energy supply...

294

Algorithms for Mumford Curves Ralph Morrison and Qingchun Ren  

E-Print Network [OSTI]

discuss specific methods and future work for hyperelliptic Mumford curves. 1. Introduction Curves over non geometry, which looks at the images in Rn of curves under coordinate-wise valuation, these are balanced complete with respect to a nontrivial non-archimedean valuation. Unless otherwise stated, | · | will denote

Boyer, Edmond

295

Oil production models with normal rate curves Dudley Stark  

E-Print Network [OSTI]

Oil production models with normal rate curves Dudley Stark School of Mathematical Sciences Queen;Abstract The normal curve has been used to fit the rate of both world and U.S.A. oil production. In this paper we give the first theoretical basis for these curve fittings. It is well known that oil field

Stark, Dudley

296

Geodesic conic subdivision curves on surfaces J. Estrada Sarlabous  

E-Print Network [OSTI]

Geodesic conic subdivision curves on surfaces J. Estrada Sarlabous V. Hern´andez Mederos N. L Matem´atica UFAL Maceio, Brazil Email: dimas@mat.ufal.br Fig. 1. Geodesic conic subdivision curves is inspired in the concept of geodesic B´ezier curves. Starting with a geodesic control polygon with vertices

297

HOW MUCH INFLUENCE DOES CONSTRUCTION HAVE ON CURVED STEEL  

E-Print Network [OSTI]

HOW MUCH INFLUENCE DOES CONSTRUCTION HAVE ON CURVED STEEL BRIDGES? RESULTS FROM EXPERIMENTAL UNIVERSITY IBC-00-58 Keywords: curved, steel, girder, bridge, construction, erection, fabrication, testing and analytical research program to study curved steel bridge behavior. The program centered on testing a series

298

COMPUTER GENERATION OF TYPE CURVES SUBMITIED TO THE DEPARTMENTOF PETROLEUMENGINEERING  

E-Print Network [OSTI]

COMPUTER GENERATION OF TYPE CURVES A REPORT SUBMITIED TO THE DEPARTMENTOF PETROLEUMENGINEERING data. This paper presents some previously published type curves and the computer programs that were between two parallel sealing faults. The governing equations for these curves are derived. The computer

Stanford University

299

Tracking Endocardium Using Optical Flow along Iso-Value Curve  

E-Print Network [OSTI]

1 Tracking Endocardium Using Optical Flow along Iso-Value Curve Qi Duan1, Elsa D. Angelini2 indicators. · A framework of optical flow along iso-value curves is proposed and applied to several cardiac;9 OF along Iso-value Curves · In myocardial motion analysis, motion fields are projected along specific

300

Calibrating Curved Crystals Used for Plasma Spectroscopy  

SciTech Connect (OSTI)

The throughput and resolving power of an X-ray spectrometer that uses a curved crystal as the diffraction element is determined primarily by the crystal X-ray reflectivity properties. This poster presents a measurement technique for these crystal parameters using a simple diode source to produce a narrow spectral band. The results from measurements on concave elliptical polyethylene terephthalate (PET) crystals and convex potassium acid phthalate (KAP) crystals show large variations in the key parameters compared to those from the flat crystal.

Haugh, M. J., Jacoby, K. D., Ross, P. W., Rochau, G. Wu, M., Regan, S. P., Barrios, M. A.

2012-10-29T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Wave regularity in curve integrable spacetimes  

E-Print Network [OSTI]

The idea of defining a gravitational singularity as an obstruction to the dynamical evolution of a test field (described by a PDE) rather than the dynamical evolution of a particle (described by a geodesics) is explored. In particular, the concept of wave regularity is introduced which serves to show that the classical singularities in curve integrable spacetimes do not interrupt the well-posedness of the wave equation. The techniques used also provide arguments that can be extended to establish when a classically singular spacetime remains singular in a semi-classical picture.

Yafet Sanchez Sanchez

2015-02-23T23:59:59.000Z

302

Decline curve analysis for horizontal wells  

E-Print Network [OSTI]

support kept me from losing sight of my goals. Thanks to Sam Hou, Joseph Wang, Robert Liau, James Wang, and Shou for their company and in particular to Li Fan and Mrs. Shou-Lee Chang for their caring and delicious meals when I forgot my dinner. Thanks... Pressure (L/2xe= 0. 2) Composite Dimensionless Flow Rate Integral and Flow Rate Integral Derivative Functions Type Curve for an Infinite-Conductivity Horizontal Well Located in the Center of a Square Drainage Area, Producing at Constant Bottomhole...

Shih, Min-Yu

1994-01-01T23:59:59.000Z

303

Analysis of natural gas supply strategies at Fort Drum  

SciTech Connect (OSTI)

This analysis investigates strategies for Fort Drum to acquire a reliable natural gas supply while reducing its gas supply costs. The purpose of this study is to recommend an optimal supply mix based on the life-cycle costs of each strategy analyzed. In particular, this study is intended to provide initial guidance as to whether or not the building and operating of a propane-air mixing station is a feasible alternative to the current gas acquisition strategy. The analysis proceeded by defining the components of supply (gas purchase, gas transport, supplemental fuel supply); identifying alternative options for each supply component; constructing gas supply strategies from different combinations of the options available for each supply component and calculating the life-cycle costs of each supply strategy under a set of different scenarios reflecting the uncertainty of future events.

Stucky, D.J.; Shankle, S.A.; Anderson, D.M.

1992-07-01T23:59:59.000Z

304

Comparative study of InGaP/GaAs high electron mobility transistors with upper and lower delta-doped supplied layers  

SciTech Connect (OSTI)

Influence corresponding to the position of {delta}-doped supplied layer on InGaP/GaAs high electron mobility transistors is comparatively studied by two-dimensional simulation analysis. The simulated results exhibit that the device with lower {delta}-doped supplied layer shows a higher gate potential barrier height, a higher saturation output current, a larger magnitude of negative threshold voltage, and broader gate voltage swing, as compared to the device with upper {delta}-doped supplied layer. Nevertheless, it has smaller transconductance and inferior high-frequency characteristics in the device with lower {delta}-doped supplied layer. Furthermore, a knee effect in current-voltage curves is observed at low drain-to-source voltage in the two devices, which is investigated in this article.

Tsai, Jung-Hui, E-mail: jhtsai@nknucc.nknu.edu.tw; Ye, Sheng-Shiun [National Kaohsiung Normal University, Department of Electronic Engineering, Taiwan (China); Guo, Der-Feng [Air Force Academy, Kaohsiung, Department of Electronic Engineering, Taiwan (China); Lour, Wen-Shiung [National Taiwan Ocean University, Department of Electrical Engineering, Taiwan (China)

2012-04-15T23:59:59.000Z

305

Residual oil conversion in Ashland FCC Units  

SciTech Connect (OSTI)

Ashland Petroleum Company is a production-poor refining and marketing company. A company must have refining flexibility to compete in today's crude and marketing situation. Ashland has adopted a dual approach to achieving the required refining flexibility: development and construction of the RCC process, and development of techniques to practice residual oil conversion in Ashland FCC units. This paper discusses the operating techniques Ashland has used to allow residual oil conversion to be practiced in their present day FCC's and shows some of the yields which have been achieved.

Barger, D.F.; Miller, C.B.

1983-03-01T23:59:59.000Z

306

Residual dust charges in discharge afterglow  

SciTech Connect (OSTI)

An on-ground measurement of dust-particle residual charges in the afterglow of a dusty plasma was performed in a rf discharge. An upward thermophoretic force was used to balance the gravitational force. It was found that positively charged, negatively charged, and neutral dust particles coexisted for more than 1 min after the discharge was switched off. The mean residual charge for 200-nm-radius particles was measured. The dust particle mean charge is about -5e at a pressure of 1.2 mbar and about -3e at a pressure of 0.4 mbar.

Coueedel, L.; Mikikian, M.; Boufendi, L.; Samarian, A. A. [GREMI - Groupe de Recherches sur l'Energetique des Milieux Ionises, CNRS/Universite d'Orleans, 14 rue d'Issoudun, 45067 Orleans Cedex 2 (France); School of Physics A28, University of Sydney, NSW 2006 (Australia)

2006-08-15T23:59:59.000Z

307

Algebraic quantum field theory in curved spacetimes  

E-Print Network [OSTI]

This article sets out the framework of algebraic quantum field theory in curved spacetimes, based on the idea of local covariance. In this framework, a quantum field theory is modelled by a functor from a category of spacetimes to a category of ($C^*$)-algebras obeying supplementary conditions. Among other things: (a) the key idea of relative Cauchy evolution is described in detail, and related to the stress-energy tensor; (b) a systematic "rigidity argument" is used to generalise results from flat to curved spacetimes; (c) a detailed discussion of the issue of selection of physical states is given, linking notions of stability at microscopic, mesoscopic and macroscopic scales; (d) the notion of subtheories and global gauge transformations are formalised; (e) it is shown that the general framework excludes the possibility of there being a single preferred state in each spacetime, if the choice of states is local and covariant. Many of the ideas are illustrated by the example of the free Klein-Gordon theory, which is given a new "universal definition".

Christopher J. Fewster; Rainer Verch

2015-04-02T23:59:59.000Z

308

Petroleum supply monthly, October 1991. [Contains glossary  

SciTech Connect (OSTI)

Data presented in this report describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importer, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics 14 figs., 56 tabs.

Not Available

1991-10-30T23:59:59.000Z

309

Petroleum Supply Monthly, September 1990. [Contains glossary  

SciTech Connect (OSTI)

Data presented in this PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. 12 figs., 46 tabs.

Whited, D.; Jacobus, P. (eds.)

1990-11-28T23:59:59.000Z

310

Petroleum supply monthly, October 1990. [Contains Glossary  

SciTech Connect (OSTI)

Data presented in this report describes the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. 12 figs., 54 tabs.

Not Available

1990-12-27T23:59:59.000Z

311

Procurement Options for New Renewable Electricity Supply  

SciTech Connect (OSTI)

State renewable portfolio standard (RPS) policies require utilities and load-serving entities (LSEs) to procure renewable energy generation. Utility procurement options may be a function of state policy and regulatory preferences, and in some cases, may be dictated by legislative authority. Utilities and LSEs commonly use competitive solicitations or bilateral contracting to procure renewable energy supply to meet RPS mandates. However, policymakers and regulators in several states are beginning to explore the use of alternatives, namely feed-in tariffs (FITs) and auctions to procure renewable energy supply. This report evaluates four procurement strategies (competitive solicitations, bilateral contracting, FITs, and auctions) against four main criteria: (1) pricing; (2) complexity and efficiency of the procurement process; (3) impacts on developers access to markets; and (4) ability to complement utility decision-making processes. These criteria were chosen because they take into account the perspective of each group of stakeholders: ratepayers, regulators, utilities, investors, and developers.

Kreycik, C. E.; Couture, T. D.; Cory, K. S.

2011-12-01T23:59:59.000Z

312

Huntsman-Enron close supply deals  

SciTech Connect (OSTI)

Huntsman Corp. and Enron Liquid Services has signed ethylene supply agreements with consumers for their joint 1.5-billion lbs/year steam cracker. Huntsman says participants will be announced next week. Initial plans call for the unit to be built at Huntsman`s Port Arthur, TX complex, with startup scheduled for 1999. Huntsman says engineering, procurement, and financing should be in place by the end of the year. The unit will supply Huntsman`s growing internal needs for ethylene and propylene and bolster its position in the Gulf merchant market and will increase Huntsman`s ethylene capacity to more than 3.3 billion lbs/year. Enron`s extensive pipeline system will provide feedstock and be used as a distribution network for ethylene customers.

NONE

1996-08-14T23:59:59.000Z

313

Electrochemical chlorination for purifying domestic water supplies  

E-Print Network [OSTI]

. 9 amps, the total residual was 0. 1 mg 1 With the decreased current density, there was considerably less anode deterioration; but it was still excessive, wearing down the anode and deczessing the quality of the water. An asbestos diaphragm... was used between the cathode and anode I in the sixth model to make it more similar to a diaphragm chlorine cell, The asbestos diaphragm keeps the hydroxide iona at the cathode, thereby reducing the amount of water electrolysis. The cathode...

Peters, Joseph Ludwig

2012-06-07T23:59:59.000Z

314

Water on Earth Source % of Supply  

E-Print Network [OSTI]

1 Water on Earth Source % of Supply Oceans 97.08 Ice Sheets and Glaciers 1.99 Ground Water 0.62 Atmosphere 0.29 Lakes (Fresh) 0.01 Inland Seas / Salt Water Lakes 0.005 Soil Moisture 0.004 Rivers 0.001 Water · Water is the solvent, the medium and the participant in most of the chemical reactions occurring

Cochran-Stafira, D. Liane

315

Rice Supply, Demand and Related Government Programs.  

E-Print Network [OSTI]

2 percent of the world's rice, but is the third largest exporter of rice. The United States depends on export markets to absorb roughly half of the domestic production of rice: domestic disappearance accounts for only about half of total production.... The ratio of total disappearance to total supply indicates that rice stocks were disposed of through domestic and export channels in proper relation to total production until the 1954-55 crops. Surplus rice stocks beginning with the 1954 crop resulted from...

Kincannon, John A.

1957-01-01T23:59:59.000Z

316

Automatic Methods for Predicting Functionally Important Residues  

E-Print Network [OSTI]

Pazos and Alfonso Valencia* Protein Design Group National Center for Biotechnology, Cantoblanco Madrid of protein families into subfamilies in the search for those positions that could have some functional families, testing the statistical meaning of the Tree-determinant residues predicted by three different

Pazos, Florencio

317

Residual Energy Spectrum of Solar Wind Turbulence  

E-Print Network [OSTI]

It has long been known that the energy in velocity and magnetic field fluctuations in the solar wind is not in equipartition. In this paper, we present an analysis of 5 years of Wind data at 1 AU to investigate the reason for this. The residual energy (difference between energy in velocity and magnetic field fluctuations) was calculated using both the standard magnetohydrodynamic (MHD) normalization for the magnetic field and a kinetic version, which includes temperature anisotropies and drifts between particle species. It was found that with the kinetic normalization, the fluctuations are closer to equipartition, with a mean normalized residual energy of sigma_r = -0.19 and mean Alfven ratio of r_A = 0.71. The spectrum of residual energy, in the kinetic normalization, was found to be steeper than both the velocity and magnetic field spectra, consistent with some recent MHD turbulence predictions and numerical simulations, having a spectral index close to -1.9. The local properties of residual energy and cros...

Chen, C H K; Salem, C S; Maruca, B A

2013-01-01T23:59:59.000Z

318

Chemical Stabilization of Hanford Tank Residual Waste  

SciTech Connect (OSTI)

Three different chemical treatment methods were tested for their ability to stabilize residual waste from Hanford tank C-202 for reducing contaminant release (Tc, Cr, and U in particular). The three treatment methods tested were lime addition [Ca(OH)2], an in-situ Ceramicrete waste form based on chemically bonded phosphate ceramics, and a ferrous iron/goethite treatment. These approaches rely on formation of insoluble forms of the contaminants of concern (lime addition and ceramicrete) and chemical reduction followed by co-precipitation (ferrous iron/goethite incorporation treatment). The results have demonstrated that release of the three most significant mobile contaminants of concern from tank residual wastes can be dramatically reduced after treatment compared to contact with simulated grout porewater without treatment. For uranium, all three treatments methods reduced the leachable uranium concentrations by well over three orders of magnitude. In the case of uranium and technetium, released concentrations were well below their respective MCLs for the wastes tested. For tank C-202 residual waste, chromium release concentrations were above the MCL but were considerably reduced relative to untreated tank waste. This innovative approach has the potential to revolutionize Hanford’s tank retrieval process, by allowing larger volumes of residual waste to be left in tanks while providing an acceptably low level of risk with respect to contaminant release that is protective of the environment and human health. Such an approach could enable DOE to realize significant cost savings through streamlined retrieval and closure operations.

Cantrell, Kirk J.; Um, Wooyong; Williams, Benjamin D.; Bowden, Mark E.; Gartman, Brandy N.; Lukens, Wayne W.; Buck, Edgar C.; Mausolf, Edward J.

2014-03-01T23:59:59.000Z

319

Curved Spacetimes and Curved Graphene: a status report of the Weyl-symmetry approach  

E-Print Network [OSTI]

This is a status report about the ongoing work on the realization of quantum field theory on curved graphene spacetimes that uses Weyl symmetry. The programme is actively pursued from many different perspectives. Here we point to what has been done, and to what needs to be done.

Iorio, Alfredo

2014-01-01T23:59:59.000Z

320

Curved Spacetimes and Curved Graphene: a status report of the Weyl-symmetry approach  

E-Print Network [OSTI]

This is a status report about the ongoing work on the realization of quantum field theory on curved graphene spacetimes that uses Weyl symmetry. The programme is actively pursued from many different perspectives. Here we point to what has been done, and to what needs to be done.

Alfredo Iorio

2014-12-15T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Sustainable Supply Chain Network Design: A Multicriteria Perspective Anna Nagurney  

E-Print Network [OSTI]

Sustainable Supply Chain Network Design: A Multicriteria Perspective Anna Nagurney Department West Hartford, Connecticut 06117 August 2009; revised April 2010 International Journal of Sustainable framework for the design of sustainable supply chain networks. We consider a firm that is engaged

Nagurney, Anna

322

SC COLLABORATOR: A SERVICE ORIENTED FRAMEWORK FOR CONSTRUCTION SUPPLY CHAIN  

E-Print Network [OSTI]

, service oriented architecture (SOA) with open source technologies is a desirable computing modelSC COLLABORATOR: A SERVICE ORIENTED FRAMEWORK FOR CONSTRUCTION SUPPLY CHAIN COLLABORATION for construction supply chain collaboration and management, through a prototype service oriented system framework

Stanford University

323

National Spherical Torus Experiment (NSTX) Power Supply Real Time Controller  

E-Print Network [OSTI]

systems according to pre­programmed current derivatives. II. POWER SUPPLIES & CIRCUITS TO BE CONTROLLED isolated from each other but subject to the same "Firing Generator" (FG). Each PSS Magnets Power Supply

324

Application Of Geothermal Energy To The Supply Of Electricity...  

Open Energy Info (EERE)

To The Supply Of Electricity In Rural Areas Jump to: navigation, search OpenEI Reference LibraryAdd to library Journal Article: Application Of Geothermal Energy To The Supply Of...

325

Property Tax Exemption for Machinery, Equipment, Materials, and Supplies (Kansas)  

Broader source: Energy.gov [DOE]

The Property Tax Exemption for Machinery, Equipment, Materials, and Supplies exists for low-dollar items of machinery, equipment, materials and supplies used for business purposes, or in activities...

326

SKU segmentation strategy for a global retail supply chain  

E-Print Network [OSTI]

The concept of using different supply chain strategies for different products or product families is a fairly simple component of supply chain management. This practice, known as SKU segmentation, is widely used by many ...

Jin, Huiping, M. Eng. Massachusetts Institute of Technology

2014-01-01T23:59:59.000Z

327

How Markets Slowly Digest Changes in Supply and Demand  

E-Print Network [OSTI]

CHAPTER 2 How Markets Slowly Digest Changes in Supply and Demand Jean-Philippe Bouchaud Science-Holland, Elsevier, Inc. All rights reserved. 57 #12;58 Chapter 2 · How Markets Slowly Digest Changes in Supply

328

Hydrogen storage of energy for small power supply systems  

E-Print Network [OSTI]

Power supply systems for cell phone base stations using hydrogen energy storage, fuel cells or hydrogen-burning generators, and a backup generator could offer an improvement over current power supply systems. Two categories ...

Monaghan, Rory F. D. (Rory Francis Desmond)

2005-01-01T23:59:59.000Z

329

Quantum fields on closed timelike curves  

SciTech Connect (OSTI)

Recently, there has been much interest in the evolution of quantum particles on closed timelike curves (CTCs). However, such models typically assume pointlike particles with only two degrees of freedom; a very questionable assumption given the relativistic setting of the problem. We show that it is possible to generalize the Deutsch model of CTCs to fields using the equivalent circuit formalism. We give examples for coherent, squeezed, and single-photon states interacting with the CTC via a beamsplitter. The model is then generalized further to account for the smooth transition to normal quantum mechanics as the CTC becomes much smaller than the size of the modes interacting on it. In this limit, we find that the system behaves like a standard quantum-mechanical feedback loop.

Pienaar, J. L.; Myers, C. R.; Ralph, T. C. [School of Mathematics and Physics, The University of Queensland, Brisbane 4072, Queensland (Australia)

2011-12-15T23:59:59.000Z

330

Direct current uninterruptible power supply method and system  

DOE Patents [OSTI]

A method and system are described for providing a direct current (DC) uninterruptible power supply with the method including, for example: continuously supplying fuel to a turbine; converting mechanical power from the turbine into alternating current (AC) electrical power; converting the AC electrical power to DC power within a predetermined voltage level range; supplying the DC power to a load; and maintaining a DC load voltage within the predetermined voltage level range by adjusting the amount of fuel supplied to the turbine.

Sinha, Gautam

2003-12-02T23:59:59.000Z

331

SUPERNOVA LIGHT CURVES POWERED BY FALLBACK ACCRETION  

SciTech Connect (OSTI)

Some fraction of the material ejected in a core collapse supernova explosion may remain bound to the compact remnant, and eventually turn around and fall back. We show that the late time ({approx}>days) power potentially associated with the accretion of this 'fallback' material could significantly affect the optical light curve, in some cases producing super-luminous or otherwise peculiar supernovae. We use spherically symmetric hydrodynamical models to estimate the accretion rate at late times for a range of progenitor masses and radii and explosion energies. The accretion rate onto the proto-neutron star or black hole decreases as M-dot {proportional_to}t{sup -5/3} at late times, but its normalization can be significantly enhanced at low explosion energies, in very massive stars, or if a strong reverse shock wave forms at the helium/hydrogen interface in the progenitor. If the resulting super-Eddington accretion drives an outflow which thermalizes in the outgoing ejecta, the supernova debris will be re-energized at a time when photons can diffuse out efficiently. The resulting light curves are different and more diverse than previous fallback supernova models which ignored the input of accretion power and produced short-lived, dim transients. The possible outcomes when fallback accretion power is significant include super-luminous ({approx}> 10{sup 44} erg s{sup -1}) Type II events of both short and long durations, as well as luminous Type I events from compact stars that may have experienced significant mass loss. Accretion power may unbind the remaining infalling material, causing a sudden decrease in the brightness of some long duration Type II events. This scenario may be relevant for explaining some of the recently discovered classes of peculiar and rare supernovae.

Dexter, Jason; Kasen, Daniel, E-mail: jdexter@berkeley.edu [Departments of Physics and Astronomy, University of California, Berkeley, CA 94720 (United States)

2013-07-20T23:59:59.000Z

332

Optimization of California's Water Supply System: Results and Insights  

E-Print Network [OSTI]

headings: Optimization; California; Water supply; Water shortage. Introduction Water is scarceOptimization of California's Water Supply System: Results and Insights Marion W. Jenkins1 ; Jay R-engineering optimization model of California's water supply system. The results of this 4-year effort illustrate the value

Pasternack, Gregory B.

333

Lagrangean Decomposition Algorithm for Supply Chain Redesign of Electric Motors  

E-Print Network [OSTI]

Lagrangean Decomposition Algorithm for Supply Chain Redesign of Electric Motors Industry Yongheng Redesign of Electric Motors Industry Introduction of the Supply Chain Model 3/22/13 2 Analia Rodriguez #12 Decomposition Algorithm for Supply Chain Redesign of Electric Motors Industry #12;Lagrangean Decomposition

Grossmann, Ignacio E.

334

Risk management in Chemical Supply Chains Rajagopalan Srinivasana,b  

E-Print Network [OSTI]

an agent-based framework for modeling and simulating the supply chain activities in a refinery, and operations in the refinery. Other external agents emulate the crude exchange, oil suppliers, and 3PLs attention. As an example, consider a petroleum refinery supply chain. 1.1. Petroleum Refinery Supply Chain

Alvarado, MatĂ­as

335

Design of Sustainable Supply Chains for Sustainable Cities Anna Nagurney  

E-Print Network [OSTI]

Design of Sustainable Supply Chains for Sustainable Cities Anna Nagurney Isenberg School of sustainable supply chains with a focus on cities that captures the frequency of network link operations, which and frequency costs, and meeting demand. Keywords: sustainable cities, supply chains, sustainability, network

Nagurney, Anna

336

National Spherical Torus Experiment (NSTX) Power Supply Real Time Controller  

E-Print Network [OSTI]

derivatives. II. POWER SUPPLIES & CIRCUITS TO BE CONTROLLED A. Power Supplies NSTX utilizes the PPPL "Power Supply Sections" (PSS) which are electrically isolated from each other but subject to the same "Firing PSS by phase controlling the thyristor firing pulses in accordance with a Control Word received

337

THE JET PULSE POWER SUPPLY SYSTEM J. B. HICKS  

E-Print Network [OSTI]

between the two major components of the power supply (flywheel-generator-convertors (FGC) and transformer between the two possible components of the power supply, i. e. flywheel. generator-convertors and transformer-controlled-convertors. The proposed JET power supply system is described, together with an outline

Paris-Sud XI, Université de

338

California's Summer 2004 Electricity Supply and Demand Outlook  

E-Print Network [OSTI]

forecast for 2004 is higher to reflect increased demand from more robust economic growth. In this newCALIFORNIA ENERGY COMMISSION California's Summer 2004 Electricity Supply and Demand Outlook Supply and Demand Outlook The California Energy Commission staff's electricity supply and demand outlook

339

Simulating the Afghanistan-Pakistan opium supply chain  

SciTech Connect (OSTI)

This paper outlines an opium supply chain using the Hilmand province of Afghanistan as exemplar. The opium supply chain model follows the transformation of opium poppy seed through cultivation and chemical alteration to brown heroin base. The purpose of modeling and simulating the Afghanistan-Pakistan opium supply chain is to discover and test strategies that will disrupt this criminal enterprise.

Watkins, Jennifer H [Los Alamos National Laboratory; Mac Kerrow, Edward P [Los Alamos National Laboratory; Merritt, Terence [Los Alamos National Laboratory

2010-01-01T23:59:59.000Z

340

STANDARD TERMS OF PURCHASE APPLICABLE TO SUPPLY AND SERVICES CONTRACTS  

E-Print Network [OSTI]

STANDARD TERMS OF PURCHASE APPLICABLE TO SUPPLY AND SERVICES CONTRACTS ENTERED INTO BY SUD TOULON and its co-contracting parties for all government supplies and services contracts entered into pursuant supply and services contracts in its version annexed to the Decree of 19 January 2009 approving

Chamroukhi, Faicel

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Hybrid Heterogeneous Energy Supply Networks Farinaz Koushanfar and Azalia Mirhoseini  

E-Print Network [OSTI]

Hybrid Heterogeneous Energy Supply Networks Farinaz Koushanfar and Azalia Mirhoseini Department--Efficient energy supply, storage, and distribution are key technical challenges for design and operation of electronic systems. In particular, energy supply is the most scarce resource and constraint for mobile

342

Alberta's Energy Reserves 2007 and Supply/Demand Outlook  

E-Print Network [OSTI]

Alberta's Energy Reserves 2007 and Supply/Demand Outlook 2008-2017 0 ST98-2008 Energy Resources RESOURCES CONSERVATION BOARD ST98-2008: Alberta's Energy Reserves 2007 and Supply/Demand Outlook 2008: Reserves Andy Burrowes, Rick Marsh, Nehru Ramdin, and Curtis Evans; Supply/Demand and Economics

Laughlin, Robert B.

343

Supply chain management (SCM) involves the management of materials and information across the entire supply chain. This includes raw material  

E-Print Network [OSTI]

Supply chain management (SCM) involves the management of materials and information across this concentration will be required to take three core courses: Materials and Supply Chain Management, Transportation Purchasing identify global sources of materials, select vendors, and manage negotiati

Calgary, University of

344

Understanding the Hellings and Downs curve for pulsar timing arrays in terms of sound and electromagnetic waves  

E-Print Network [OSTI]

Searches for gravitational-wave backgrounds using pulsar timing arrays look for correlations in the timing residuals induced by the background across the pulsars in the array. The correlation signature of an isotropic, unpolarized gravitational-wave background predicted by general relativity follows the so-called Hellings and Downs curve, which is a relatively simple function of the angle between a pair of pulsars. To aid students and beginning researchers interested in pulsar timing, we give a pedagogical discussion of the Helling and Downs curve for pulsar timing arrays, considering simpler analogous scenarios involving sound and electromagnetic waves. We calculate Hellings-and-Downs type functions for these two scenarios and develop a framework suitable for doing more general correlation calculations.

Jenet, Fredrick A

2014-01-01T23:59:59.000Z

345

Understanding the Hellings and Downs curve for pulsar timing arrays in terms of sound and electromagnetic waves  

E-Print Network [OSTI]

Searches for gravitational-wave backgrounds using pulsar timing arrays look for correlations in the timing residuals induced by the background across the pulsars in the array. The correlation signature of an isotropic, unpolarized gravitational-wave background predicted by general relativity follows the so-called Hellings and Downs curve, which is a relatively simple function of the angle between a pair of pulsars. To aid students and beginning researchers interested in pulsar timing, we give a pedagogical discussion of the Helling and Downs curve for pulsar timing arrays, considering simpler analogous scenarios involving sound and electromagnetic waves. We calculate Hellings-and-Downs type functions for these two scenarios and develop a framework suitable for doing more general correlation calculations.

Fredrick A. Jenet; Joseph D. Romano

2014-12-03T23:59:59.000Z

346

Section B: Supplies, Services and Costs  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-Up from the Gridwise Global1WasteRecoveryAwards SECTION B SUPPLIES AND SERVICES AND

347

Total Supplemental Supply of Natural Gas  

Gasoline and Diesel Fuel Update (EIA)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"ClickPipelines About U.S. NaturalA. Michael SchaalNovember 26, 2008Product: Total Supplemental Supply

348

End-of-life vehicle recycling : state of the art of resource recovery from shredder residue.  

SciTech Connect (OSTI)

Each year, more than 50 million vehicles reach the end of their service life throughout the world. More than 95% of these vehicles enter a comprehensive recycling infrastructure that includes auto parts recyclers/dismantlers, remanufacturers, and material recyclers (shredders). Today, about 75% of automotive materials are profitably recycled via (1) parts reuse and parts and components remanufacturing and (2) ultimately by the scrap processing (shredding) industry. The process by which the scrap processors recover metal scrap from automobiles involves shredding the obsolete automobiles, along with other obsolete metal-containing products (such as white goods, industrial scrap, and demolition debris), and recovering the metals from the shredded material. The single largest source of recycled ferrous scrap for the iron and steel industry is obsolete automobiles. The non-metallic fraction that remains after the metals are recovered from the shredded materials (about 25% of the weight of the vehicle)--commonly called shredder residue--is disposed of in landfills. Over the past 10 to 15 years, a significant amount of research and development has been undertaken to enhance the recycle rate of end-of-life vehicles (ELVs), including enhancing dismantling techniques and improving remanufacturing operations. However, most of the effort has focused on developing technology to recover materials, such as polymers, from shredder residue. To make future vehicles more energy efficient, more lighter-weight materials--primarily polymers and polymer composites--will be used in manufacturing these vehicles. These materials increase the percentage of shredder residue that must be disposed of, compared with the percentage of metals. Therefore, as the complexity of automotive materials and systems increases, new technologies will be required to sustain and maximize the ultimate recycling of these materials and systems at end-of-life. Argonne National Laboratory (Argonne), in cooperation with the Vehicle Recycling Partnership (VRP) and the American Plastics Council (APC), is working to develop technology for recycling materials from shredder residue. Several other organizations worldwide are also working on developing technology for recycling shredder residue. Without a commercially viable shredder industry, our nation may face greater environmental challenges and a decreased supply of quality scrap and be forced to turn to primary ores for the production of finished metals. This document presents a review of the state of the art in shredder residue recycling. Available technologies and emerging technologies for the recycling of materials from shredder residue are discussed.

Jody, B. J.; Daniels, E. J.; Energy Systems

2007-03-21T23:59:59.000Z

349

Ris Energy Report 4 Interaction between supply and end-use 4 8 Interaction between supply and end-use  

E-Print Network [OSTI]

of the wholesale power markets has intro- duced market-based pricing for the marginal electricity supply. PricesRisø Energy Report 4 Interaction between supply and end-use 4 8 Interaction between supply and end and consumption is a market issue, in the sense that the market balance is set some time before the physical

350

Description & Careers Supply Chain Management is how business gets done. Supply chain management spans all movement and storage of raw  

E-Print Network [OSTI]

management spans all movement and storage of raw materials, work-in-process inventory, and finished goods of supply chains, resource managers of material or manufacturing resources planning (MRP), and processDescription & Careers The Field Supply Chain Management is how business gets done. Supply chain

Lin, Xiaodong

351

Description & Careers Supply Chain Management is how business gets done. Supply chain management spans all movement and storage of raw  

E-Print Network [OSTI]

management spans all movement and storage of raw materials, work-in-process inventory, and finished goods managers of supply chains, resource managers of material or manufacturing resources planning (MRPDescription & Careers The Field Supply Chain Management is how business gets done. Supply chain

Lin, Xiaodong

352

Petroleum supply monthly, with data from June 1996  

SciTech Connect (OSTI)

The Petroleum Supply Division (PSD) of the Energy Information Administration (EIA) collects and published information on petroleum supply and disposition in the United States. The information is collected through a series of surveys that make up the Petroleum Supply Reporting System (PSRS). The PSRS data are published in the Weekly Petroleum Status Report (WPSR), Petroleum Supply Monthly (PSM), and Petroleum Supply Annual (PSA). This report presents information on crude oil production, crude oil imports and exports, refinery operations, natural gas processing, transportation, and oxygenate data.

NONE

1996-08-01T23:59:59.000Z

353

Restricted Natural Gas Supply Case (released in AEO2005)  

Reports and Publications (EIA)

The restricted natural gas supply case provides an analysis of the energy-economic implications of a scenario in which future gas supply is significantly more constrained than assumed in the reference case. Future natural gas supply conditions could be constrained because of problems with the construction and operation of large new energy projects, and because the future rate of technological progress could be significantly lower than the historical rate. Although the restricted natural gas supply case represents a plausible set of constraints on future natural gas supply, it is not intended to represent what is likely to happen in the future.

2005-01-01T23:59:59.000Z

354

Construction of Fractal Surfaces by Recurrent Fractal Interpolation Curves  

E-Print Network [OSTI]

A method to construct fractal surfaces by recurrent fractal curves is provided. First we construct fractal interpolation curves using a recurrent iterated functions system(RIFS) with function scaling factors and estimate their box-counting dimension. Then we present a method of construction of wider class of fractal surfaces by fractal curves and Lipschitz functions and calculate the box-counting dimension of the constructed surfaces. Finally, we combine both methods to have more flexible constructions of fractal surfaces.

Chol-hui Yun; Hyong-chol O.; Hui-chol Choi

2014-08-12T23:59:59.000Z

355

Biofuel Boundaries: Estimating the Medium-Term Supply Potential of Domestic Biofuels  

E-Print Network [OSTI]

industrial residues - such as black liquor and sawdust, andindustry residues such as black liquor are mostly (93%) (18)industry residues, such as black liquor from their current

Jones, Andrew; O'Hare, Michael; Farrell, Alexander

2007-01-01T23:59:59.000Z

356

D-Branes in Curved Space  

SciTech Connect (OSTI)

This thesis is a study of D-branes in string compactifications. In this context, D-branes are relevant as an important component of the nonperturbative spectrum, as an incisive probe of these backgrounds, and as a natural stringy tool for localizing gauge interactions. In the first part of the thesis, we discuss half-BPS D-branes in compactifications of type II string theory on Calabi-Yau threefolds. The results we describe for these objects are pertinent both in their role as stringy brane-worlds, and in their role as solitonic objects. In particular, we determine couplings of these branes to the moduli determining the closed-string geometry, both perturbatively and non-perturbatively in the worldsheet expansion. We provide a local model for transitions in moduli space where the BPS spectrum jumps, and discuss the extension of mirror symmetry between Calabi-Yau manifolds to the case when D-branes are present. The next section is an interlude which provides some applications of D-branes to other curved backgrounds of string theory. In particular, we discuss a surprising phenomenon in which fundamental strings moving through background Ramond-Ramond fields dissolve into large spherical D3-branes. This mechanism is used to explain a previously-mysterious fact discovered via the AdS-CFT correspondence. Next, we make a connection between type IIA string vacua of the type discussed in the first section and M-theory compactifications on manifolds of G{sub 2} holonomy. Finally we discuss constructions of string vacua which do not have large radius limits. In the final part of the thesis, we develop techniques for studying the worldsheets of open strings ending on the curved D-branes studied in the first section. More precisely, we formulate a large class of massive two-dimensional gauge theories coupled to boundary matter, which flow in the infrared to the relevant boundary conformal field theories. Along with many other applications, these techniques are used to describe world-volume theories of point-like D-probes of various Calabi-Yau threefolds.

McGreevy, John Austen; /Stanford U., Phys. Dept.

2005-07-06T23:59:59.000Z

357

Thin layer chromatography residue applicator sampler  

DOE Patents [OSTI]

A thin layer chromatograph residue applicator sampler. The residue applicator sampler provides for rapid analysis of samples containing high explosives, chemical warfare, and other analyses of interest under field conditions. This satisfied the need for a field-deployable, small, hand-held, all-in-one device for efficient sampling, sample dissolution, and sample application to an analytical technique. The residue applicator sampler includes a sampling sponge that is resistant to most chemicals and is fastened via a plastic handle in a hermetically sealed tube containing a known amount of solvent. Upon use, the wetted sponge is removed from the sealed tube and used as a swiping device across an environmental sample. The sponge is then replaced in the hermetically sealed tube where the sample remains contained and dissolved in the solvent. A small pipette tip is removably contained in the hermetically sealed tube. The sponge is removed and placed into the pipette tip where a squeezing-out of the dissolved sample from the sponge into the pipette tip results in a droplet captured in a vial for later instrumental analysis, or applied directly to a thin layer chromatography plate for immediate analysis.

Nunes, Peter J. (Danville, CA); Kelly, Fredrick R. (Modesto, CA); Haas, Jeffrey S. (San Ramon, CA); Andresen, Brian D. (Livermore, CA)

2007-07-24T23:59:59.000Z

358

UNIVERSITY OF CALIFORNIA, DAVIS Water Supply and Prospects in Baja California  

E-Print Network [OSTI]

......................................................... 20 Environmental ................................................... 21 Chapter 4: Water Supply Infrastructure and Management ......... 24 Water supply infrastructure ................................... 26 Water governance and management ......................... 30 Chapter 5: Water Supply Prospects

Lund, Jay R.

359

E-Print Network 3.0 - arterial blood supply Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Topic 14 -Stroke 1. Blood supply to the brain Summary: Territories supplied by anterior, middle and posterior cerebral arteries. Topic 14 - Stroke 1. Blood supply... of acute...

360

A Fuel Cell Power Supply for Long Duration Balloon Flights Using Stored Cryogens  

E-Print Network [OSTI]

CA, (1966) LBNL-40618 A FUEL CELL POWER SUPPLY FOR LONGLBNL-40618 A FUEL CELL POWER SUPPLY FOR LONG DURATIONreport describes a fuel cell power supply configuration.

Green, Michael A.; Manikowski, A.; Noland, G.; Golden, R.L.

1997-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

INFLUENCE OF SUPPLY AIR TEMPERATURE ON UNDERFLOOR AIR DISTRIBUTION (UFAD) SYSTEM ENERGY PERFORMANCE  

E-Print Network [OSTI]

chilled water cooling coil, and supply fan. The fan is aspecify the VAV box cooling design supply air temperature (the underfloor supply plenum (thereby, reducing room cooling

2012-01-01T23:59:59.000Z

362

CBTL Design Case Summary Conventional Feedstock Supply System - Herbaceous  

SciTech Connect (OSTI)

A conventional bale feedstock design has been established that represents supply system technologies, costs, and logistics that are achievable today for supplying herbaceous feedstocks as a blendstock with coal for energy production. Efforts are made to identify bottlenecks and optimize the efficiency and capacities of this supply system, within the constraints of existing local feedstock supplies, equipment, and permitting requirements. The feedstock supply system logistics operations encompass all of the activities necessary to move herbaceous biomass feedstock from the production location to the conversion reactor ready for blending and insertion. This supply system includes operations that are currently available such that costs and logistics are reasonable and reliable. The system modeled for this research project includes the uses of field-dried corn stover or switchgrass as a feedstock to annually supply an 800,000 DM ton conversion facility.

Christopher T. Wright; Erin M. Searcy

2012-02-01T23:59:59.000Z

363

Embargo on Iran hurts supply firms  

SciTech Connect (OSTI)

When President Clinton dropped an embargo on Iran, he also collided with oilfield supply companies to the tune of some $662.5 million. The embargo locked Iran away from oil exports to the US and some imports from the US in an attempt to stop Iran from: building a nuclear weapons stockpile; threatening the Persian Gulf with conventional military operations, and supporting terrorism. Most people would agree with the need to stop that activity. But, the supply companies would have preferred something less drastic. The Petroleum Equipment Suppliers Association, and the Tom Wheatley Valve Co. of Houston, said Iran owes suppliers approximately a half-billion dollars in receivables. That money may never be recovered, and it could send some companies into bankruptcy. In addition, the embargo cuts off $325 million in business the US conducts with Iran and about half of that business goes to the oil industry. If you plug that $162.5 million into Department of Labor statistics that say each $1 million sustains 20 jobs, the industry stands to lose 3250 jobs.

Lyle, D.

1995-06-01T23:59:59.000Z

364

Comparison of operating speeds at spiral transition and circular curves  

E-Print Network [OSTI]

acceleration, fijs; and V = speed, mph In evaluating the models, it was found that the spiral length increases with increasing speed, but does not become unreasonably long. It was also found that the spiral length and spiral ang e epen o y on 1 d d nl... curves provide deceptive information to drivers is based on crash data for spiral curves, he does not present data for comparable circular curves In addition, the issue of whether the spiral curve is causing the crashes or whether crash rates...

Passetti, Karl Andrew

1998-01-01T23:59:59.000Z

365

A Practical Model for Mobile, Residual, and Entrapped NAPL in...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

A Practical Model for Mobile, Residual, and Entrapped NAPL in Water-Wet Porous Media. A Practical Model for Mobile, Residual, and Entrapped NAPL in Water-Wet Porous Media....

366

In-situ method for treating residual sodium  

SciTech Connect (OSTI)

A unique process for deactivating residual sodium in Liquid Metal Fast Breeder Reactor (LMFBR) systems which uses humidified (but not saturated) carbon dioxide at ambient temperature and pressure to convert residual sodium into solid sodium bicarbonate.

Sherman, Steven R. (Idaho Falls, ID); Henslee, S. Paul (Idaho Falls, ID)

2005-07-19T23:59:59.000Z

367

Testing regression models with residuals as data by Xia Hua.  

E-Print Network [OSTI]

Abstract In polynomial regression ... . In this thesis, I developed a residual based test, the turning point test for residuals, which tests the hypothesis that the kth order polynomial regression holds with ... while the ...

Hua, Xia, Ph. D. Massachusetts Institute of Technology

2010-01-01T23:59:59.000Z

368

NEURAL NETWORK RESIDUAL STOCHASTIC COSIMULATION FOR ENVIRONMENTAL DATA ANALYSIS  

E-Print Network [OSTI]

on radioactive soil contamination from the Chernobyl fallout. Introduction The problem of analysing environmentalNEURAL NETWORK RESIDUAL STOCHASTIC COSIMULATION FOR ENVIRONMENTAL DATA ANALYSIS V. Demyanov, M original method of stochastic simulation of environmental data -- Neural Network Residual Sequential

369

In-Situ Method for Treating Residual Sodium  

DOE Patents [OSTI]

A unique process for deactivating residual sodium in Liquid Metal Fast Breeder Reactor (LMFBR) systems which uses humidified (but not saturated) carbon dioxide at ambient temperature and pressure to convert residual sodium into solid sodium bicarbonate.

Sherman, Steven R.; Henslee, S. Paul

2005-07-19T23:59:59.000Z

370

1-D Transforms for the Motion Compensation Residual  

E-Print Network [OSTI]

Transforms used in image coding are also commonly used to compress prediction residuals in video coding. Prediction residuals have different spatial characteristics from images, and it is useful to develop transforms that ...

Kamisli, Fatih

371

Calibration curves for some standard Gap Tests  

SciTech Connect (OSTI)

The relative shock sensitivities of explosive compositions are commonly assessed using a family of experiments that can be described by the generic term ''Gap Test.'' Gap tests include a donor charge, a test sample, and a spacer, or gap, between two explosives charges. The donor charge, gap material, and test dimensions are held constant within each different version of the gap test. The thickness of the gap is then varied to find the value at which 50% of the test samples will detonate. The gap tests measure the ease with a high-order detonation can be established in the test explosive, or the ''detonability,'' of the explosive. Test results are best reported in terms of the gap thickness at the 50% point. It is also useful to define the shock pressure transmitted into the test sample at the detonation threshold. This requires calibrating the gap test in terms of shock pressure in the gap as a function of the gap thickness. It also requires a knowledge of the shock Hugoniot of the sample explosive. We used the 2DE reactive hydrodynamic code with Forest Fire burn rates for the donor explosives to calculate calibration curves for several gap tests. The model calculations give pressure and particle velocity on the centerline of the experimental set-up and provide information about the curvature and pulse width of the shock wave. 10 refs., 1 fig.

Bowman, A.L.; Sommer, S.C.

1989-01-01T23:59:59.000Z

372

Ghost condensate model of flat rotation curves  

E-Print Network [OSTI]

An effective action of ghost condensate with higher derivatives creates a source of gravity and mimics a dark matter in spiral galaxies. We present a spherically symmetric static solution of Einstein--Hilbert equations with the ghost condensate at large distances, where flat rotation curves are reproduced in leading order over small ratio of two energy scales characterizing constant temporal and spatial derivatives of ghost field: $\\mu_*^2$ and $\\mu_\\star^2$, respectively, with a hierarchy $\\mu_\\star\\ll \\mu_*$. We assume that a mechanism of hierarchy is provided by a global monopole in the center of galaxy. An estimate based on the solution and observed velocities of rotations in the asymptotic region of flatness, gives $\\mu_*\\sim 10^{19}$ GeV and the monopole scale in a GUT range $\\mu_\\star\\sim 10^{16}$ GeV, while a velocity of rotation $v_0$ is determined by the ratio: $ \\sqrt{2} v_0^2= \\mu_\\star^2/\\mu_*^2$. A critical acceleration is introduced and naturally evaluated of the order of Hubble rate, that represents the Milgrom's acceleration.

V. V. Kiselev

2005-07-29T23:59:59.000Z

373

Aerodynamics of a rigid curved kite wing  

E-Print Network [OSTI]

A preliminary numerical study on the aerodynamics of a kite wing for high altitude wind power generators is proposed. Tethered kites are a key element of an innovative wind energy technology, which aims to capture energy from the wind at higher altitudes than conventional wind towers. We present the results obtained from three-dimensional finite volume numerical simulations of the steady air flow past a three-dimensional curved rectangular kite wing (aspect ratio equal to 3.2, Reynolds number equal to 3x10^6). Two angles of incidence -- a standard incidence for the flight of a tethered airfoil (6{\\deg}) and an incidence close to the stall (18{\\deg}) -- were considered. The simulations were performed by solving the Reynolds Averaged Navier-Stokes flow model using the industrial STAR-CCM+ code. The overall aerodynamic characteristics of the kite wing were determined and compared to the aerodynamic characteristics of the flat rectangular non twisted wing with an identical aspect ratio and section (Clark Y profil...

Maneia, Gianmauro; Tordella, Daniela; Iovieno, Michele

2013-01-01T23:59:59.000Z

374

Instanton effects and quantum spectral curves  

E-Print Network [OSTI]

We study a spectral problem associated to the quantization of a spectral curve arising in local mirror symmetry. The perturbative WKB quantization condition is determined by the quantum periods, or equivalently by the refined topological string in the Nekrasov-Shatashvili (NS) limit. We show that the information encoded in the quantum periods is radically insufficient to determine the spectrum: there is an infinite series of instanton corrections, which are non-perturbative in \\hbar, and lead to an exact WKB quantization condition. Moreover, we conjecture the precise form of the instanton corrections: they are determined by the standard or un-refined topological string free energy, and we test our conjecture successfully against numerical calculations of the spectrum. This suggests that the non-perturbative sector of the NS refined topological string contains information about the standard topological string. As an application of the WKB quantization condition, we explain some recent observations relating membrane instanton corrections in ABJM theory to the refined topological string.

Johan Kallen; Marcos Marino

2014-04-16T23:59:59.000Z

375

Galaxy rotation curves in de Sitter space  

E-Print Network [OSTI]

The observed positive cosmological constant $\\Lambda$ and Hubble constant $H_0$ introduce a background of de Sitter gravitons of mass $m_0=\\sqrt{\\Lambda}\\hbar/c$ at a non-relativistic temperature $k_BT_{dS}=a_{H}\\hbar/\\pi c$, $a_H=H_0c$, where $\\hbar$ denotes the Planck constant and $c$ the velocity of light. In this cosmology, gravitational interactions are parameterized by the inverse temperature $\\beta=T_{dS}/T$ of the vacuum. The high and low $\\beta$ limits produce an acceleration $a\\simeq\\sqrt{a_Na_0}$, $a_0=2a_{H}/(1+\\beta_{dS})\\simeq 1.37\\times 10^{-8}$ cm s$^{-2}$, observed in observed galaxy rotation curves and, respectively, Newton's law. Gravitation may be anomalously weak in a transition about $2.17\\, {M_{11}^{1/2}} \\, \\mbox{kpc}$ around a galaxy of $M=M_{11}10^{11}M_\\odot$.

Maurice H. P. M. van Putten

2014-11-10T23:59:59.000Z

376

Bioassays of weathered residues of several organic phosphorus insecticides  

E-Print Network [OSTI]

residues on fruit, forage crops, and animals. The effects of temperature, relative humid? ity, light, wind, and simulated rain on the residual toxicities of many of the chlorinated hydrocarbon insecticides used for the control of cotton insects were... humidity. Sunlight was found to be an important factor in reducing the residual effectiveness of dieldrin. Wind and simulated rain reduced the period of residual effectiveness of many of the compounds tested. These investigators have shown...

Hightower, Billie Gene

2013-10-04T23:59:59.000Z

377

RESIDUAL STRESS AND YOUNG'S MODULUS MEASUREMENT OF CAPACITIVE MICROMACHINED ULTRASONIC  

E-Print Network [OSTI]

deposition technique yields residual stress of around 100 MPa and Young's modulus of around 300 GPa. Keywords's modulus, Poisson's ratio, and residual stress of the deposited thin films. In this paper, we propose a newRESIDUAL STRESS AND YOUNG'S MODULUS MEASUREMENT OF CAPACITIVE MICROMACHINED ULTRASONIC TRANSDUCER

Khuri-Yakub, Butrus T. "Pierre"

378

SUPERLAYER RESIDUAL STRESS EFFECT ON THE INDENTATION ADHESION MEASUREMENTS  

E-Print Network [OSTI]

as a function of film thickness and residual stress. These films were sputter deposited onto thermally oxidized deposition parameters were controlled to produce either a compressive residual stress of 1 GPa or a tensile in a study of compressive and tensile residual stresses created during sputter deposition of tungsten

Volinsky, Alex A.

379

Welding residual stresses in ferritic power plant steels  

E-Print Network [OSTI]

REVIEW Welding residual stresses in ferritic power plant steels J. A. Francis*1 , H. K. D. H require therefore, an accounting of residual stresses, which often are introduced during welding. To do in the estimation of welding residual stresses in austenitic stainless steels. The progress has been less convincing

Cambridge, University of

380

Recirculating Molten Metal Supply System And Method  

DOE Patents [OSTI]

The melter furnace includes a heating chamber (16), a pump chamber (18), a degassing chamber (20), and a filter chamber (22). The pump chamber (18) is located adjacent the heating chamber (16) and houses a molten metal pump (30). The degassing chamber (20) is located adjacent and in fluid communication with the pump chamber (18), and houses a degassing mechanism (36). The filter chamber (22) is located adjacent and in fluid communication with the degassing chamber (20). The filter chamber (22) includes a molten metal filter (38). The melter furnace (12) is used to supply molten metal to an externally located holder furnace (14), which then recirculates molten metal back to the melter furnace (12).

Kinosz, Michael J. (Apollo, PA); Meyer, Thomas N. (Murrysville, PA)

2003-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Optimizing rotational acceleration curves for minimum energy use in electric  

E-Print Network [OSTI]

Optimizing rotational acceleration curves for minimum energy use in electric motors. 12/15/06 Fall the optimal efficiency of a motor for any input values of motor constants, distance, or time. In every of the inspiration to find which rotational acceleration curve for the used motors would be most efficient. We really

Ruina, Andy L.

382

Generic measures for geodesic flows on nonpositively curved manifolds  

E-Print Network [OSTI]

Generic measures for geodesic flows on nonpositively curved manifolds Yves Coud`ene, Barbara the generic invariant probability measures for the geodesic flow on connected complete nonpositively curved subset of the set of all probability measures invariant by the geodesic flow. The proof of K. Sigmund

Paris-Sud XI, Université de

383

Stochastic Analysis of Wind Turbine Power Curves Edgar Anahua  

E-Print Network [OSTI]

of the wind turbine to its desired power production; and ii) the stochastic force (noise), whichStochastic Analysis of Wind Turbine Power Curves Edgar Anahua Oldenburg 2007 Zur Homepage der Dissertation #12;#12;Stochastic Analysis of Wind Turbine Power Curves Edgar Anahua Von der Fakult¨at f

Peinke, Joachim

384

The Dimension of the SLE Curves Vincent BEFFARA  

E-Print Network [OSTI]

generating a Schramm-Loewner Evolution (SLE) process, with parameter 0: We prove that, with probability one (Kt) is generated by a random curve : [0, ) H (called the trace of the SLE or the SLE curve clusters) and = 8/3 (this follows from the description of the outer frontier of SLE6 -- or planar Brownian

Beffara, Vincent

385

NON-CLOSED CURVES IN Rn WITH FINITE TOTAL FIRST  

E-Print Network [OSTI]

], and Kondo and Tanaka [14] have examined the global properties of the total curvature of a curveNON-CLOSED CURVES IN Rn WITH FINITE TOTAL FIRST CURVATURE ARISING FROM THE SOLUTIONS OF AN ODE P finite total first curvature. If all the roots of the associated characteristic polynomial are simple, we

Gilkey, Peter B

386

CURVES OF GENUS 2 WITH p 2 MULTIPLICATION  

E-Print Network [OSTI]

thesis, which looks at curves of genus 2 whose jacobians have p 2 multiplication, with the generalisedCURVES OF GENUS 2 WITH p 2 MULTIPLICATION PETER R. BENDING Abstract We give a universal family, and let f be a newform on \\Gamma 1 (N) whose field of Fourier coefficients is F (F is a totally real field

387

Ashot Minasyan SQ-universality and residual properties. . . -slide #1 The SQ-universality and residual properties of  

E-Print Network [OSTI]

Ashot Minasyan SQ-universality and residual properties. . . - slide #1 The SQ-universality Main Results Ashot Minasyan SQ-universality and residual properties. . . - slide #2 SQ-universality and residual properties. . . - slide #2 SQ-universality A group G is called SQ-universal if any countable group

Minasyan, Ashot

388

CBTL Design Case Summary Conventional Feedstock Supply System - Woody  

SciTech Connect (OSTI)

A conventional woody feedstock design has been developed that represents supply system technologies, costs, and logistics that are achievable today for supplying woody biomass as a blendstock with coal for energy production. Efforts are made to identify bottlenecks and optimize the efficiency and capacities of this supply system, within the constraints and consideration of existing local feedstock supplies, equipment, and permitting requirements. The feedstock supply system logistics operations encompass all of the activities necessary to move woody biomass from the production location to the conversion reactor ready for blending and insertion. This supply system includes operations that are currently available such that costs and logistics are reasonable and reliable. The system modeled for this research project includes the use of the slash stream since it is a more conservative analysis and represents the material actually used in the experimental part of the project.

Christopher T. Wright; Erin M. Searcy

2012-02-01T23:59:59.000Z

389

E-beam high voltage switching power supply  

DOE Patents [OSTI]

A high-power power supply produces a controllable, constant high voltage put under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules.

Shimer, Daniel W. (Danville, CA); Lange, Arnold C. (Livermore, CA)

1996-01-01T23:59:59.000Z

390

E-beam high voltage switching power supply  

DOE Patents [OSTI]

A high-power power supply produces a controllable, constant high voltage output under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules. 5 figs.

Shimer, D.W.; Lange, A.C.

1996-10-15T23:59:59.000Z

391

Modular high voltage power supply for chemical analysis  

DOE Patents [OSTI]

A high voltage power supply for use in a system such as a microfluidics system, uses a DC-DC converter in parallel with a voltage-controlled resistor. A feedback circuit provides a control signal for the DC-DC converter and voltage-controlled resistor so as to regulate the output voltage of the high voltage power supply, as well as, to sink or source current from the high voltage supply.

Stamps, James F. (Livermore, CA); Yee, Daniel D. (Dublin, CA)

2008-07-15T23:59:59.000Z

392

Modular high voltage power supply for chemical analysis  

SciTech Connect (OSTI)

A high voltage power supply for use in a system such as a microfluidics system, uses a DC-DC converter in parallel with a voltage-controlled resistor. A feedback circuit provides a control signal for the DC-DC converter and voltage-controlled resistor so as to regulate the output voltage of the high voltage power supply, as well as, to sink or source current from the high voltage supply.

Stamps, James F. (Livermore, CA); Yee, Daniel D. (Dublin, CA)

2010-05-04T23:59:59.000Z

393

Modular high voltage power supply for chemical analysis  

DOE Patents [OSTI]

A high voltage power supply for use in a system such as a microfluidics system, uses a DC--DC converter in parallel with a voltage-controlled resistor. A feedback circuit provides a control signal for the DC--DC converter and voltage-controlled resistor so as to regulate the output voltage of the high voltage power supply, as well as, to sink or source current from the high voltage supply.

Stamps, James F. (Livermore, CA); Yee, Daniel D. (Dublin, CA)

2007-01-09T23:59:59.000Z

394

PCBs have declined more than DDT-group residues in Arctic ringed seals (Phoca hispida) between 1972 and 1981  

SciTech Connect (OSTI)

Mean DDT-group concentrations in the blubber of western Arctic ringed seals (Phoca hispida) sampled in 1981 were less than 1..mu..g.g/sup -1/ wet weight. Male seals had higher concentrations than did females. PCB concentrations were about half of those in a sample of the same population taken in 1972, when allowance was made for the variation of residue concentrations with age, sex, and condition. This decline probably results from the ban on PCB manufacture and use imposed in the early 1970s. Concentrations of DDT-group residues did not show any clear decline over the same interval, and the relative proportions of p,p'-DDT and p,p'-DDE suggested that there is a continuing supply of DDT to the western Arctic. The most probable source of this is by atmospheric or water transport from the Far East, where DDT was used until at least the late 1970s.

Addison, R.F.; Zinck, M.E.; Smith, T.G.

1986-03-01T23:59:59.000Z

395

Westinghouse Small Modular Reactor nuclear steam supply system design  

SciTech Connect (OSTI)

The Westinghouse Small Modular Reactor (SMR) is an 800 MWt (>225 MWe) integral pressurized water reactor (iPWR), in which all of the components typically associated with the nuclear steam supply system (NSSS) of a nuclear power plant are incorporated within a single reactor pressure vessel. This paper is the first in a series of four papers which describe the design and functionality of the Westinghouse SMR. Also described in this series are the key drivers influencing the design of the Westinghouse SMR and the unique passive safety features of the Westinghouse SMR. Several critical motivators contributed to the development and integration of the Westinghouse SMR design. These design driving motivators dictated the final configuration of the Westinghouse SMR to varying degrees, depending on the specific features under consideration. These design drivers include safety, economics, AP1000{sup R} reactor expertise and experience, research and development requirements, functionality of systems and components, size of the systems and vessels, simplicity of design, and licensing requirements. The Westinghouse SMR NSSS consists of an integral reactor vessel within a compact containment vessel. The core is located in the bottom of the reactor vessel and is composed of 89 modified Westinghouse 17x17 Robust Fuel Assemblies (RFA). These modified fuel assemblies have an active core length of only 2.4 m (8 ft) long, and the entirety of the core is encompassed by a radial reflector. The Westinghouse SMR core operates on a 24 month fuel cycle. The reactor vessel is approximately 24.4 m (80 ft) long and 3.7 m (12 ft) in diameter in order to facilitate standard rail shipping to the site. The reactor vessel houses hot and cold leg channels to facilitate coolant flow, control rod drive mechanisms (CRDM), instrumentation and cabling, an intermediate flange to separate flow and instrumentation and facilitate simpler refueling, a pressurizer, a straight tube, recirculating steam generator, and eight reactor coolant pumps (RCP). The containment vessel is 27.1 m (89 ft) long and 9.8 m (32 ft) in diameter, and is designed to withstand pressures up to 1.7 MPa (250 psi). It is completely submerged in a pool of water serving as a heat sink and radiation shield. Housed within the containment are four combined core makeup tanks (CMT)/passive residual heat removal (PRHR) heat exchangers, two in-containment pools (ICP), two ICP tanks and four valves which function as the automatic depressurization system (ADS). The PRHR heat exchangers are thermally connected to two different ultimate heat sink (UHS) tanks which provide transient cooling capabilities. (authors)

Memmott, M. J.; Harkness, A. W.; Van Wyk, J. [Westinghouse Electric Company LLC, 600 Cranberry Woods Drive, Cranberry Twp. PA 16066 (United States)

2012-07-01T23:59:59.000Z

396

Beyond the Aquifer : planning for San Antonio's future water supply.  

E-Print Network [OSTI]

??This report examines water supply planning issues in San Antonio, Texas. San Antonio is unique among large cities in the United States in that it… (more)

Laughlin, Nathan Daniel

2010-01-01T23:59:59.000Z

397

Addressing Biomass Supply Chain Challenges With AFEX™ Technology  

Broader source: Energy.gov [DOE]

Plenary IV: Advances in Bioenergy Feedstocks—From Field to Fuel Addressing Biomass Supply Chain Challenges With AFEX™ Technology Allen Julian, Chief Business Officer, MBI

398

Electric Vehicle Supply Equipment (EVSE) Test Report: AeroVironment  

Broader source: Energy.gov (indexed) [DOE]

pROGRAM Electric Vehicle Supply Equipment (EVSE) Test Report: AeroVironment EVSE Features LED status light EVSE Specifications Grid connection Hardwired Connector type J1772 Test...

399

Danny Lloyd Supply Purchasing Manager & Jlab Small Business...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Danny Lloyd Supply Purchasing Manager & Jlab Small Business Program Manager JSA Mentor-Protg Program Thomas Jefferson National Accelerator Facility Newport, News, Virginia...

400

Model for Energy Supply System Alternatives and their General...  

Open Energy Info (EERE)

System Alternatives and their General Environmental Impacts (MESSAGE) (Redirected from Model for Energy Supply System Alternatives and their General Environmental Impacts) Jump to:...

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

The 'Supply-of-Storage' for Natural Gas in California  

E-Print Network [OSTI]

the Hedging Effectiveness of Natural Gas Futures. ” EnergyCommission. (2002). “Natural Gas Supply and Infrastructureand Price Dynamics in Natural Gas City Gate Markets. ”

Uria, Rocio; Williams, Jeffrey

2005-01-01T23:59:59.000Z

402

Multi-unit Auctions with Unknown Supply [Extended Abstract  

E-Print Network [OSTI]

Multi-unit Auctions with Unknown Supply [Extended Abstract] Mohammad Mahdian Microsoft Research Redmond, WA, USA mahdian@microsoft.com Amin Saberi Stanford University Stanford, CA, USA saberi

Saberi, Amin

403

Numerical Study of Affine Supply Function Equilibrium in AC ...  

E-Print Network [OSTI]

supply function in the same form of the marginal cost function. [1]. Because of this bid-based .... for the locational marginal prices (LMPs). In compact notation, the ...

2007-07-17T23:59:59.000Z

404

Econometric Models of Discrete/Continuous Supply Decisions under Uncertainty  

E-Print Network [OSTI]

357-382. XcFadden, D. "Econometric Net Supply Systems forpoint of view of the econometric investigator. the producerin New Directions in Econometric Modeling and Forecasting in

Hanemann, W. Michael; Tsur, Yacov

1982-01-01T23:59:59.000Z

405

automated supply chain: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

the impact that customer allocations have on key cost and service indicators at Intel Corporation. Allocations provide a method to fill orders during constrained supply, when...

406

automating supply chains: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

the impact that customer allocations have on key cost and service indicators at Intel Corporation. Allocations provide a method to fill orders during constrained supply, when...

407

automotive supply chain: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

the impact that customer allocations have on key cost and service indicators at Intel Corporation. Allocations provide a method to fill orders during constrained supply, when...

408

An Improved Stochastic Optimization Model for Water Supply ...  

E-Print Network [OSTI]

Mar 9, 2014 ... Abstract: This study investigates a pump scheduling problem for the collection, transfer and storage of water in water supply systems in urban ...

Jonathan De La Vega

2014-03-09T23:59:59.000Z

409

Measuring Iranian Petroleum Downstream Supply Chain Management Performance;.  

E-Print Network [OSTI]

?? Petroleum downstream is a strategic and important industry for any nation. It supplies most of transport and travel needs and provides petrochemical business raw… (more)

Norouzi, Saba

2013-01-01T23:59:59.000Z

410

Modelling the South African fresh fruit export supply chain  

E-Print Network [OSTI]

Modelling the South African fresh fruit export supply chain Frank Gerald Ortmann Thesis presented, cooling and transportation. The capacities of packhouses, cold stores and terminals are found

van Vuuren, Jan H.

411

Technology and Organizational Factors in the Notebook Industry Supply Chain  

E-Print Network [OSTI]

the speed, efficiency, and precision of inter-organizationalefficiency and effectiveness of the tightly clustered supply chain. That performance is a function of technical and organizational

Foster, William; Cheng, Zhang; Dedrick, Jason; Kraemer, Kenneth L

2006-01-01T23:59:59.000Z

412

Combination process for upgrading residual oils  

SciTech Connect (OSTI)

This patent describes a method for upgrading high boiling residual portions of crude oils comprising metal contaminants, porphyrins, asphaltenes and high molecular weight multi-ring hydrocarbon material. It comprises: charging a high boiling residual portion of crude oil admixed with diluent in contact with suspended upflowing substantially inert fluidizable solids particulate material at an elevated thermal visbreaking temperature in a riser contact zone for a time sufficient to recover therefrom a vaporous hydrocarbon product higher boiling than gasoline partially decarbonized and demetallized to a lower contaminating metals level, quenching the vaporous product of thermal visbreaking below its dew point after separation from solids, charging quenched thermally modified high boiling hydrocarbon product with a crystalline zeolite cracking catalyst under cracking conditions for a hydrocarbon residence time in a riser cracking zone; recovering a hydrocarbon conversion product; separating a combined C{sub 4} minus wet gas product stream of the visbreaking and zeolite catalyst cracking operating to recover a C{sub 3}-C{sub 4} rich fraction separately from a C{sub 2} minus dry gas product fraction, and regenerating the crystalline zeolite contcontaining catalyst.

Busch, L.E.; Walters, P.W.; Zandona, O.

1990-01-16T23:59:59.000Z

413

Alcohol production from agricultural and forestry residues  

SciTech Connect (OSTI)

Technologies available for the production of ethanol from whole corn are reviewed. Particular emphasis is placed on the environmental aspects of the process, including land utilization and possible air and water pollutants. Suggestions are made for technological changes intended to improve the economics of the process as well as to reduce some of the pollution from by-product disposal. Ethanol may be derived from renewable cellulosic substances by either enzymatic or acid hydrolysis of cellulose to sugar, followed by conventional fermentation and distillation. The use of two agricultural residues - corn stover (field stalks remaining after harvest) and straw from wheat crops - is reviewed as a cellulosic feedstock. Two processes have been evaluated with regard to environmental impact - a two-stage acid process developed by G.T. Tsao of Purdue University and an enzymatic process based on the laboratory findings of C.R. Wilke of the University of California, Berkeley. The environmental residuals expected from the manufacture of methyl and ethyl alcohols from woody biomass are covered. The methanol is produced in a gasification process, whereas ethanol is produced by hydrolysis and fermentation processes similar to those used to derive ethanol from cellulosic materials.

Dale, L; Opilla, R; Surles, T

1980-09-01T23:59:59.000Z

414

Alcohol production from agricultural and forestry residues  

SciTech Connect (OSTI)

A variety of carbohydrate sources can be used as raw material for the production of ethanol. Section 1 is a review of technologies available for the production of ethanol from whole corn. Particular emphasis is placed on the environmental aspects of the process, including land utilization and possible air and water pollutants. Suggestions are made for technological changes intended to improve the economics of the process as well as to reduce some of the pollution from by-product disposal. Ethanol may be derived from renewable cellulosic substances by either enzymatic or acid hydrolysis of cellulose to sugar, followed by conventional fermentation and distillation. Section 2 is a review of the use of two agricultural residues - corn stover (field stalks remaining after harvest) and straw from wheat crops - as a cellulosic feedstock. Two processes have been evaluated with regard to environmental impact - a two-stage acid process developed by G.T. Tsao of Purdue University and an enzymatic process based on the laboratory findings of C.R. Wilke of the University of California, Berkeley. Section 3 deals with the environmental residuals expected from the manufacture of methyl and ethyl alcohols from woody biomass. The methanol is produced in a gasification process, whereas ethanol is produced by hydrolysis and fermentation processes similar to those used to derive ethanol from cellulosic materials.

Opilla, R.; Dale, L.; Surles, T.

1980-05-01T23:59:59.000Z

415

Combustion turbine deposition observations from residual and simulated residual oil studies  

SciTech Connect (OSTI)

Burning residual oil in utility combustion turbines and the consequent deposition on blades and vanes may adversely affect reliability and operation. Corrosion and deposition data for combustion turbine materials have been obtained through dynamic testing in pressurized passages. The deposition produced by the 1900/sup 0/F (1038/sup 0/C) combustion gases from a simulated and a real residual oil on cooled Udimet 500 surfaces is described. Higher deposition rates for the doped fuel than for the real residual oil raised questions of whether true simulation with this approach can be achieved. Particles 4-8..mu.. m in diameter predominated in the gas stream, with some fraction in the 0.1-12 ..mu.. m range. Deposition rates seemed to be influenced by thermophoretic delivery of small molten particles, tentatively identified as magnesium pyro and metavanadates and free vanadium pentoxide, which may act to bond the larger solid particles arriving by inertial impaction to turbine surfaces. Estimated maintenance intervals for current utility turbines operating with washed and treated residual oil agreed well with field experience.

Whitlow, G.A.; Cohn, A.; Lee, S.Y.; Mulik, P.R.; Sherlock, T.P.; Wenglarz, R.A.

1983-01-01T23:59:59.000Z

416

Progress Report on Alloy 617 Isochronous Stress-Strain Curves  

SciTech Connect (OSTI)

Isochronous stress-strain curves for Alloy 617 up to a temperature of 1000°C will be required to qualify the material for elevated temperature design in Section III, Division 1, Subsection NH of the ASME Boiler and Pressure Vessel Code. Several potential methods for developing these curves are reviewed in this report. It is shown that in general power-law creep is the rate controlling deformation mechanism for a wide range of alloy heats, test temperatures and stresses. Measurement of the strain rate sensitivity of Alloy 617 indicates that the material is highly strain rate sensitive in the tensile deformation range above about 750°C. This suggests that the concept of a hot tensile curve as a bounding case on the isochronous stress-strain diagrams is problematic. The impact of strain rate on the hot tensile curves is examined and it is concluded that incorporating such a curve is only meaningful if a single tensile strain rate (typically the ASTM standard rate of 0.5%/min) is arbitrarily defined. Current experimentally determined creep data are compared to isochronous stress-strain curves proposed previously by the German programs in the 1980s and by the 1990 draft ASME Code Case. Variability in how well the experimental data are represented by the proposed design curves that suggests further analysis is necessary prior to completing a new draft Code Case.

Jill K. Wright; Richard N. Wright; Nancy J. Lybeck

2014-03-01T23:59:59.000Z

417

Exhaustive search system and method using space-filling curves  

DOE Patents [OSTI]

A search system and method for one agent or for multiple agents using a space-filling curve provides a way to control one or more agents to cover an area of any space of any dimensionality using an exhaustive search pattern. An example of the space-filling curve is a Hilbert curve. The search area can be a physical geography, a cyberspace search area, or an area searchable by computing resources. The search agent can be one or more physical agents, such as a robot, and can be software agents for searching cyberspace.

Spires, Shannon V.

2003-10-21T23:59:59.000Z

418

Application of the decline curve method to aquifers  

E-Print Network [OSTI]

k = value of pointin time = value of point in time n = value of point in time 39 REFERENCES 1. Fetkovich, M. J. : "Decline Curve Analysis Using Type Curves, " JPT (June 1980) 1065-1077. 2. Havlena, D. and Odeh, A. S. : "The Material Balance...APPLICATION OF THE DECLINE CURVE METHOD TO AQUIFERS A Thesis by GIRISH VIJAY POTNIS Submitted to the Office of Graduate Studies of Texas ADAM University in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE December...

Potnis, Girish Vijay

1992-01-01T23:59:59.000Z

419

Cylinder supplied ammonia scrubber testing in IDMS  

SciTech Connect (OSTI)

This report summarizes the results of the off-line testing the Integrated DWPF Melter System (IDMS) ammonia scrubbers using ammonia supplied from cylinders. Three additional tests with ammonia are planned to verify the data collected during off-line testing. Operation of the ammonia scrubber during IDMS SRAT and SME processing will be completed during the next IDMS run. The Sludge Receipt and Adjustment Tank (SRAT) and Slurry Mix Evaporator (SME) scrubbers were successful in removing ammonia from the vapor stream to achieve ammonia vapor concentrations far below the 10 ppM vapor exit design basis. In most of the tests, the ammonia concentration in the vapor exit was lower than the detection limit of the analyzers so results are generally reported as <0.05 parts per million (ppM). During SRAT scrubber testing, the ammonia concentration was no higher than 2 ppM and during SME testing the ammonia concentration was no higher than 0.05 m.

Lambert, D.P.

1994-08-31T23:59:59.000Z

420

Physical modeling of the soil swelling curve vs. the shrinkage curve  

E-Print Network [OSTI]

Physical understanding of the links between soil swelling, texture, structure, cracking, and sample size is of great interest for the physical understanding of many processes in the soil-air-water system and for applications in civil, agricultural, and environmental engineering. The background of this work is an available chain of interconnected physical shrinkage curve models for clay, intra-aggregate matrix, aggregated soil without cracks, and soil with cracks. The objective of the work is to generalize these models to the case of swelling, and to construct the physical-swelling-model chain with a step-by-step transition from clay to aggregated soil with cracks. The generalization is based on thorough accounting for the analogies and differences between shrinkage and swelling and the corresponding use, modification, or replacement of the soil shrinkage features. Two specific soil swelling features to be used are: (i) air entrapping in pores of the contributing clay; and (ii) aggregate destruction with the f...

Chertkov, V Y

2014-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

STATE OF CALIFORNIA SUPPLY WATER TEMPERATURE RESET CONTROLS ACCEPTANCE  

E-Print Network [OSTI]

STATE OF CALIFORNIA SUPPLY WATER TEMPERATURE RESET CONTROLS ACCEPTANCE CEC-MECH-9A (Revised 08/09) CALIFORNIA ENERGY COMMISSION CERTIFICATE OF ACCEPTANCE MECH-9A NA7.5.8 Supply Water Temperature Reset, under the laws of the State of California, the information provided on this form is true and correct

422

Supplying Renewable Energy to Deferrable Loads: Algorithms and Economic Analysis  

E-Print Network [OSTI]

Supplying Renewable Energy to Deferrable Loads: Algorithms and Economic Analysis Anthony compares to price responsive demand in terms capacity gains and energy market revenues for renewable to renewable generation. I. INTRODUCTION Renewable power is emerging as a mainstream source of energy supply

Oren, Shmuel S.

423

Potential Supply Impacts of Removal of 1-Pound RVP Waiver  

E-Print Network [OSTI]

by the Office of Oil and Gas of the Energy Information Administration. General questions concerning the report, Petroleum Division #12;1 Energy Information Administration/Potential Supply Impacts of Removal of 1-Pound;2 Energy Information Administration/Potential Supply Impacts of Removal of 1-Pound Waiver provides

Patzek, Tadeusz W.

424

Funding and Federal Staffing Requirements Funding Summary (Energy Supply)  

E-Print Network [OSTI]

Funding and Federal Staffing Requirements Funding Summary (Energy Supply) (dollars in thousands) FY Buildings Zero Energy Building Design . . . . . 1,367 8,000 4,000 -4,000 -50.0% Total, Zero-Energy Buildings-Temperature Superconducting R&D . . . . . . . . . . . . . . . . . . . . . . 31,991 47,838 47,838 0 0.0% Energy Supply Energy

425

Assured Fuel Supply: Potential Conversion and Fabrication Bottlenecks  

E-Print Network [OSTI]

Assured Fuel Supply: Potential Conversion and Fabrication Bottlenecks PNNL-16951 DRAFT Authors bottlenecks that may arise in the conversion and fuel fabrication steps when used in conjunction with the U.S.-sponsored Reliable Fuel Supply (RFS) reserve. Paper is also intended to identify pathways for assessing the magnitude

426

Controlled Use Robot Colony Power Supply Gary Parker  

E-Print Network [OSTI]

of charging solar panels a continuous power station. Brooks a robot, Attila, which batteries recharged panelsControlled Use Robot Colony Power Supply Gary Parker Computer Science Connecticut College New.S.A. rszbe@conncoll.edu Abstract ­ controlled of a continuous power supply robots colony presented. builds

Parker, Gary B.

427

An Efficient Supply Modulator for Linear Wideband RF Power Amplifiers  

E-Print Network [OSTI]

for controlling the supply voltage. The switching regulator is found to be slew-limited by the bulky inductor and capacitor used to regulate the supply voltage. The proposed solution alleviates the slew rate limitation by adding a bang-bang controlled current...

Turkson, Richard

2011-10-21T23:59:59.000Z

428

Strategic safety stocks in supply chains with evolving forecasts  

E-Print Network [OSTI]

we have an evolving demand forecast. Under assumptions about the forecasts, the demand process their supply chain operations based on a forecast of future demand over some planning horizon. Furthermore stock inventory in a supply chain that is subject to a dynamic, evolving demand forecast. In particular

Graves, Stephen C.

429

IntroductiontoPowerSuppliesAN-556 National Semiconductor  

E-Print Network [OSTI]

TL G 10061 IntroductiontoPowerSuppliesAN-556 National Semiconductor Application Note 556 Ralph E ripple voltage to capacitor C1 The bridge rectifier circuit has a simple transformer but current must in a full-wave bridge for the same input voltage TL G 10061­1 FIGURE 1 Idealized Power Supply TL G 10061

Paderborn, Universität

430

FUEL SUPPLY SYSTEM ANALYSIS FOR ESF PACKAGE 1E  

SciTech Connect (OSTI)

The primary objective of this analysis is to capture new inputs relative to the design of the Fuel Supply System (FSS) at the Yucca Mountain Site Characterization Project (YMP) Exploratory Studies Facility (ESF). The new inputs are analyzed and changes to the Fuel Supply System are made as necessary.

D.F. Vanica

1995-06-14T23:59:59.000Z

431

Models for Mitigating Supply Chain Disruptions Lawrence V. Snyder  

E-Print Network [OSTI]

Example In 1998, strikes at two General Motors parts plants Snyder (Lehigh University) Supply Chain Example In 1998, strikes at two General Motors parts plants Snyder (Lehigh University) Supply Chain Example In 1998, strikes at two General Motors parts plants Led to shutdown of 100+ other parts plants

Grossmann, Ignacio E.

432

U.S. Natural Gas Supply to 2030 Larry Hughes  

E-Print Network [OSTI]

LNG Total Figure 1: U.S. natural gas supply (reference case) It should be noted that this is the reference case; the "side cases", based upon the volume of projected LNG (liquefied natural gas) imports gas supply projections for 2030 (TCF) Production Low LNG Reference High LNG Dry gas 21.99 20.83 19

Hughes, Larry

433

Power Supplies and Radio Frequency Department at Culham  

E-Print Network [OSTI]

Power Supplies and Radio Frequency Department at Culham Culham Centre for Fusion Energy #12;We employ over 70 power electrical and power electronic engineers and technicians. The department supplies power to the JET and MAST nuclear fusion experiments at Culham. Culham is fed from the grid at 400k

434

Multiobjective Genetic Algorithms for Pump Scheduling in Water Supply  

E-Print Network [OSTI]

Introduction Seeking cost reduction and energy savings in water supply by improving the operation of pumps is both an obvious as well as a very efficient possibility to consider. Without making changes that in the UK the overall energy cost for pumping in water supply is about ÂŁ70 Million p.a., the estimated

Coello, Carlos A. Coello

435

Predictive control of supply temperature in district heating systems  

E-Print Network [OSTI]

Predictive control of supply temperature in district heating systems Torben Skov Nielsen Henrik This report considers a new concept for controlling the supply temperature in district heating systems using stochastic modelling, prediction and control. A district heating systems is a di#30;cult system to control

436

CONTROL OF SUPPLY TEMPERATURE IN DISTRICT HEATING SYSTEMS  

E-Print Network [OSTI]

CONTROL OF SUPPLY TEMPERATURE IN DISTRICT HEATING SYSTEMS T.S. Nielsen, H. Madsen Informatics the supply temperature in district heating systems using stochastic modelling, prediction and control at Roskilde Varmeforsyning. The results obtained for the Roskilde district heating utility are evaluated

437

Assessment of district energy supply from Schiller Generating Station  

SciTech Connect (OSTI)

This paper addresses the feasibility analysis of retrofitting the Public Service of New Hampshire Schiller Generating Station to supply district heating to potential customers. The project involved analysis of power plant retrofit and comparison of district heating cost to the cost of heat supplied with gas boilers for a housing development in close proximity to the Schiller Station.

Hitchko, M. [Public Service Company of New Hampshire, Portsmouth, NH (United States); Major, W. [Joseph Technology Corporation, Inc., Woodcliff Lake, NJ (United States)

1995-06-01T23:59:59.000Z

438

Sustainable Fashion Supply Chain Management Under Oligopolistic Competition Brand Differentiation  

E-Print Network [OSTI]

Sustainable Fashion Supply Chain Management Under Oligopolistic Competition and Brand developed a new model of oligopolistic competition for fashion supply chains in the case of differentiated as for the solution of the case study examples. The numerical examples illustrate both the generality of the modeling

Nagurney, Anna

439

11 California Petroleum Supply, Transportation, Refining and Marketing Trends  

E-Print Network [OSTI]

11 California Petroleum Supply, Transportation, Refining and Marketing Trends Chapter 2 CALIFORNIA PETROLEUM SUPPLY, TRANSPORTATION, REFINING AND MARKETING TRENDS INTRODUCTION California is an integral part of the world oil market as a world-scale petroleum consumer. Historically, about 50 percent of this petroleum

440

BIG Energy Upgrade: Procurement and Supply Chain report  

E-Print Network [OSTI]

BIG Energy Upgrade: Procurement and Supply Chain report ­ Green Deal and Energy Efficiency ­ Green Deal and Energy Efficiency Retrofitting Supply Chains Delivery Professor S.C. Lenny Koh Dr Andrea........................................................................................................................... 26 4.5 Generalities on Procurement Best Practices

Wrigley, Stuart

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Securing the Sustainability of Global Medical Nuclear Supply Chains  

E-Print Network [OSTI]

, according to Kramer (2011), the South African Nuclear Energy Corp (Necsa) believes that the LEU productionSecuring the Sustainability of Global Medical Nuclear Supply Chains Through Economic Cost Recovery-17, 2012 University of Massachusetts Amherst Securing the Sustainability of Medical Nuclear Supply Chains

Nagurney, Anna

442

Securing the Sustainability of Global Medical Nuclear Supply Chains  

E-Print Network [OSTI]

with associated increased volumes of waste. Indeed, according to Kramer (2011), the South African Nuclear EnergySecuring the Sustainability of Global Medical Nuclear Supply Chains Through Economic Cost Recovery University of Massachusetts Amherst Securing the Sustainability of Medical Nuclear Supply Chains #12

Nagurney, Anna

443

Water Supply Planning Using an Expert Geographic Information System  

E-Print Network [OSTI]

supply and demand data; and a network flow solver, to balance the flows in networks developed by the expert GIS with input from a water resource analyst. Commonly available water demand forecasts and water supply data are used in this new planning tool...

McKinney, Daene C.; Burgin, John F.; Maidment, David R.

444

Recovery of gallium from aluminum industry residues  

SciTech Connect (OSTI)

A procedure is proposed to recover gallium from flue dust aluminum residues produced in plants by using solid-phase extraction with a commercial polyether-type polyurethane foam (PUF). Gallium can be separated from high concentrations of aluminum, iron, nickel, titanium, vanadium, copper, zinc, sulfate, fluoride, and chloride by extraction with PUF from 3 M sulfuric acid and 3 M sodium chloride concentration medium with at least a 92% efficiency. Gallium backextraction was fast and quantitative with ethanol solution. In all recovery steps commercial-grade reagents could be used, including tap water. The recovered gallium was precipitated with sodium hydroxide solution, purified by dissolution and precipitation, calcinated, and the final oxide was 98.6% pure.

Carvalho, M.S.; Neto, K.C.M.; Nobrega, A.W.; Medeiros, J.A.

2000-01-01T23:59:59.000Z

445

Method For Characterizing Residual Stress In Metals  

DOE Patents [OSTI]

A method is provided for measuring the residual stress in metals. The method includes the steps of drilling one or more holes in a metal workpiece to a preselected depth and mounting one or more acoustic sensors on the metal workpiece and connecting the sensors to an electronic detecting and recording device. A liquid metal capable of penetrating into the metal workpiece placed at the bottom of the hole or holes. A recording is made over a period of time (typically within about two hours) of the magnitude and number of noise events which occur as the liquid metal penetrates into the metal workpiece. The magnitude and number of noise events are then correlated to the internal stress in the region of the workpiece at the bottom of the hole.

Jacobson, Loren A. (Santa Fe, NM); Michel, David J. (Alexandria, VA); Wyatt, Jeffrey R. (Burke, VA)

2002-12-03T23:59:59.000Z

446

Process converts incineration slag into stabilized residue  

SciTech Connect (OSTI)

During 1973 and 1974, EMC-Services designed and built a physico-chemical treatment plant in Hombourg, in France's Alsatian region. The plant is still in operation. Since then, EMC-Services has developed substantial experience in environmental projects, becoming one of the top companies internationally with experience and practice in designing, building and operating hazardous waste treatment plants. EMC-Services operates in France in Salaise, Strasbourg, Mitry-Mory, and Saint-Vulbas, where eight incinerators treat solid, liquid, highly halogenated and nonhazardous industrial waste. The incinerators, built or updated by EMC-Services, have a total capacity of about 200,000 tons per year. In the new process, incineration of special industrial wastes produces non-volatilized solid residue or slag, which is sent for disposal, in compliance with regulations, to special disposal plants. Future European regulations will incorporate landfilling criteria requiring such slag to be stabilized.

Thauront, J.; Deneux-Mustin, S. (EMC-Services, Paris (France)); Durecu, S. (EMC-Services, Vandoeuvre-Les Nancy (France)); Fraysse, G. (EMC-Services, Saint-Vulbas (France)); Berthelin, J. (Centre de Pedologie Biologique, Vandoeuvre-Les Nancy (France))

1994-12-01T23:59:59.000Z

447

Knowledge fusion: Comparison of fuzzy curve smoothers to statistically motivated curve smoothers  

SciTech Connect (OSTI)

This report describes work during FY 95 that was sponsored by the Department of Energy, Office of Nonproliferation and National Security (NN) Knowledge Fusion (KF) Project. The project team selected satellite sensor data to use as the one main example to which its analysis algorithms would be applied. The specific sensor-fusion problem has many generic features, which make it a worthwhile problem to attempt to solve in a general way. The generic problem is to recognize events of interest from multiple time series that define a possibly noisy background. By implementing a suite of time series modeling and forecasting methods and using well-chosen alarm criteria, we reduce the number of false alarms. We then further reduce the number of false alarms by analyzing all suspicious sections of data, as judged by the alarm criteria, with pattern recognition methods. This report gives a detailed comparison of two of the forecasting methods (fuzzy forecaster and statistically motivated curve smoothers as forecasters). The two methods are compared on five simulated and five real data sets. One of the five real data sets is satellite sensor data. The conclusion is the statistically motivated curve smoother is superior on simulated data of the type we studied. The statistically motivated method is also superior on most real data. In defense of the fuzzy-logic motivated methods, we point out that fuzzy-logic methods were never intended to compete with statistical methods on numeric data. Fuzzy logic was developed to handle real-world situations where either real data was not available or was supplemented with either ``expert opinion`` or some sort of linguistic information.

Burr, T.; Strittmatter, R.B.

1996-03-01T23:59:59.000Z

448

Conservation Screening Curves to Compare Efficiency Investments to Power Plants  

E-Print Network [OSTI]

Guide: Vol. 3: Fundamentals and Methods, Supply-1986. EPRI.EPRI P- 4463-SR. May 1987. Geller, Howard, Jeff P. Harris,kWh by 4000 hours. REFERENCES EPRI, Electric Power Research

Koomey, J.G.

2008-01-01T23:59:59.000Z

449

ROTATION CURVES OF 967 SPIRAL GALAXIES: IMPLICATIONS FOR DARK MATTER.  

E-Print Network [OSTI]

We present the rotation curves of 967 spiral galaxies, obtained by deprojecting and folding the raw data published by Mathewson et al. (1992). Of these, 80 meet objective excellence criteria and are suitable for individual detailed mass modelling, while 820 are suitable for statistical studies. A preliminary analysis of theire properties confirms that rotation curves are a universal function of luminosity and that the dark matter fraction in spirals increase with decreasing luminosity. Quantitative considerations on the virial radius of dark halos allow us to make hypotheses about their structure and nature. The deprojected folded curves, the smoothed curves, and various related quantities are available via anonymous ftp at ftp://galileo.sissa.it/users/ftp/pub/psrot

Massimo Persic; Paolo Salucci; Fulvio Stel

1995-03-13T23:59:59.000Z

450

Comparison of Emperical Decline Curve Analysis for Shale Wells  

E-Print Network [OSTI]

This study compares four recently developed decline curve methods and the traditional Arps or Fetkovich approach. The four methods which are empirically formulated for shale and tight gas wells are: 1. Power Law Exponential Decline (PLE). 2...

Kanfar, Mohammed Sami

2013-07-13T23:59:59.000Z

451

Multi-Echelon Supply Chain Design in Natural Gas Industry  

E-Print Network [OSTI]

Abstract: In this paper, a framework is proposed for integrating of the operational parts of Natural Gas Transmission Systems (NGTSs) through pipelines and better coordination for the flow of natural gas and information in the system. The objective functions of this study are to provide a brief review of literature in natural gas supply chain modeling and to design a multi-echelon Supply Chain for the Natural Gas Transmission Systems (NSTSC). To achieve this, extensive and detailed studies in this field of research have been done. Subsequently, a complete study on the transmission of natural gas through pipelines, as well as the supply chain and its application, has been made in gas industry. Next, based on the operational systems in the natural gas industry, the supply chain levels are developed. These designs are very effective for modeling and optimization of the gas networks. In addition, the developed supply chain helps to reduce the costs of the NGTSs and increase customer satisfaction.

Mehrdad Nikbakht; N. Zulkifli; N. Ismail; S. Sulaiman; Abdolhossein Sadrnia; M. Suleiman

452

active site residue: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

in human transferrin and Tyr Oksana Lockridge 2008-01-01 140 RESEARCH ARTICLE Benefits of organic residues and chemical fertilizer Biology and Medicine Websites Summary: RESEARCH...

453

active site residues: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

in human transferrin and Tyr Oksana Lockridge 2008-01-01 140 RESEARCH ARTICLE Benefits of organic residues and chemical fertilizer Biology and Medicine Websites Summary: RESEARCH...

454

Table 19. U.S. Refiner Residual Fuel Oil Prices  

U.S. Energy Information Administration (EIA) Indexed Site

Prices," source for backcast estimates prior to January 1983. 19. U.S. Refiner Residual Fuel Oil Prices 36 Energy Information Administration Petroleum Marketing Annual 1996...

455

Table 19. U.S. Refiner Residual Fuel Oil Prices  

U.S. Energy Information Administration (EIA) Indexed Site

Prices," source for backcast estimates prior to January 1983. 19. U.S. Refiner Residual Fuel Oil Prices 36 Energy Information Administration Petroleum Marketing Annual 1997...

456

Residual Stresses for Structural Analysis and Fatigue Life Prediction...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Stresses for Structural Analysis and Fatigue Life Prediction in Vehicle Components: Success stories from the High Temperature Materials Laboratory (HTML) User Program Residual...

457

Wet Gasification of Ethanol Residue: A Preliminary Assessment  

SciTech Connect (OSTI)

A preliminary technoeconomic assessment has been made of several options for the application of catalytic hydrothermal gasification (wet gasification) to ethanol processing residues.

Brown, Michael D.; Elliott, Douglas C.

2008-09-22T23:59:59.000Z

458

Disappearance of fusionlike residues and the nuclear equation of state  

SciTech Connect (OSTI)

The cross sections for massive residues from {sup 40}Ca+{sup 40}Ca and {sup 40}Ar+{sup 27}Al collisions were calculated with an improved Boltzmann-Uehling-Uhlenbeck equation. The calculated residue cross sections decrease with incident energy, an effect which does not appear related to the residue excitation energy. Larger residue cross sections result from calculations with larger in-medium nucleon-nucleon cross sections or with equations of state which are less attractive at subnuclear density. This dual sensitivity may be eliminated by measurements of observables associated with the coincident light particles.

Xu, H.M.; Lynch, W.G.; Danielewicz, P.; Bertsch, G.F. (National Superconducting Cyclotron Laboratory, Michigan State University, East Lansing, MI (USA) Department of Physics, Michigan State University, East Lansing, MI (USA))

1990-08-13T23:59:59.000Z

459

acetamido trideoxyhexose residue: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

The macroscopic stress evolution is connected to a length scale of residual liquefaction displayed by microscopic mean-squared displacements. The theory describes this...

460

autophosphorylated residues required: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

though no flow is present. The macroscopic stress evolution is connected to a length scale of residual liquefaction displayed by microscopic mean-squared displacements. The...

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

abradable coating residual: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

The macroscopic stress evolution is connected to a length scale of residual liquefaction displayed by microscopic mean-squared displacements. The theory describes this...

462

Water dynamics clue to key residues in protein folding  

SciTech Connect (OSTI)

A computational method independent of experimental protein structure information is proposed to recognize key residues in protein folding, from the study of hydration water dynamics. Based on all-atom molecular dynamics simulation, two key residues are recognized with distinct water dynamical behavior in a folding process of the Trp-cage protein. The identified key residues are shown to play an essential role in both 3D structure and hydrophobic-induced collapse. With observations on hydration water dynamics around key residues, a dynamical pathway of folding can be interpreted.

Gao, Meng [State Key Laboratory for Turbulence and Complex Systems, and Department of Biomedical Engineering, and Center for Theoretical Biology, and Center for Protein Science, Peking University, Beijing 100871 (China)] [State Key Laboratory for Turbulence and Complex Systems, and Department of Biomedical Engineering, and Center for Theoretical Biology, and Center for Protein Science, Peking University, Beijing 100871 (China); Zhu, Huaiqiu, E-mail: hqzhu@pku.edu.cn [State Key Laboratory for Turbulence and Complex Systems, and Department of Biomedical Engineering, and Center for Theoretical Biology, and Center for Protein Science, Peking University, Beijing 100871 (China)] [State Key Laboratory for Turbulence and Complex Systems, and Department of Biomedical Engineering, and Center for Theoretical Biology, and Center for Protein Science, Peking University, Beijing 100871 (China); Yao, Xin-Qiu [State Key Laboratory for Turbulence and Complex Systems, and Department of Biomedical Engineering, and Center for Theoretical Biology, and Center for Protein Science, Peking University, Beijing 100871 (China) [State Key Laboratory for Turbulence and Complex Systems, and Department of Biomedical Engineering, and Center for Theoretical Biology, and Center for Protein Science, Peking University, Beijing 100871 (China); Department of Biophysics, Kyoto University, Sakyo Kyoto 606-8502 (Japan); She, Zhen-Su, E-mail: she@pku.edu.cn [State Key Laboratory for Turbulence and Complex Systems, and Department of Biomedical Engineering, and Center for Theoretical Biology, and Center for Protein Science, Peking University, Beijing 100871 (China)] [State Key Laboratory for Turbulence and Complex Systems, and Department of Biomedical Engineering, and Center for Theoretical Biology, and Center for Protein Science, Peking University, Beijing 100871 (China)

2010-01-29T23:59:59.000Z

463

HOME TRENDS/ISSUES LOGISTICS MANUFACTURING SOURCING REVERSE SUPPLY CHAIN GOVT/REGULATORY RESOURCES SCDIGEST WEBSITE The Green Supply  

E-Print Network [OSTI]

HOME TRENDS/ISSUES LOGISTICS MANUFACTURING SOURCING REVERSE SUPPLY CHAIN GOVT/REGULATORY RESOURCES SCDIGEST WEBSITE The Green Supply Chain Says: The company does not plan to actually produce the pallets themselves, but rather to offer these biodegradable planks that pallet manufacturers around the world would

464

End-of-life vehicle recycling : state of the art of resource recovery from shredder residue.  

SciTech Connect (OSTI)

Each year, more than 25 million vehicles reach the end of their service life throughout the world, and this number is rising rapidly because the number of vehicles on the roads is rapidly increasing. In the United States, more than 95% of the 10-15 million scrapped vehicles annually enter a comprehensive recycling infrastructure that includes auto parts recyclers/dismantlers, remanufacturers, and material recyclers (shredders). Today, over 75% of automotive materials, primarily the metals, are profitably recycled via (1) parts reuse and parts and components remanufacturing and (2) ultimately by the scrap processing (shredding) industry. The process by which the scrap processors recover metal scrap from automobiles involves shredding the obsolete automobile hulks, along with other obsolete metal-containing products (such as white goods, industrial scrap, and demolition debris), and recovering the metals from the shredded material. The single largest source of recycled ferrous scrap for the iron and steel industry is obsolete automobiles. The non-metallic fraction that remains after the metals are recovered from the shredded materials - commonly called shredder residue - constitutes about 25% of the weight of the vehicle, and it is disposed of in landfills. This practice is not environmentally friendly, wastes valuable resources, and may become uneconomical. Therefore, it is not sustainable. Over the past 15-20 years, a significant amount of research and development has been undertaken to enhance the recycle rate of end-of-life vehicles, including enhancing dismantling techniques and improving remanufacturing operations. However, most of the effort has been focused on developing technology to separate and recover non-metallic materials, such as polymers, from shredder residue. To make future vehicles more energy efficient, more lightweighting materials - primarily polymers, polymer composites, high-strength steels, and aluminum - will be used in manufacturing these vehicles. Many of these materials increase the percentage of shredder residue that must be disposed of, compared with the percentage of metals that are recovered. In addition, the number of hybrid vehicles and electric vehicles on the road is rapidly increasing. This trend will also introduce new materials for disposal at the end of their useful lives, including batteries. Therefore, as the complexity of automotive materials and systems increases, new technologies will be required to sustain and maximize the ultimate recycling of these materials and systems. Argonne National Laboratory (Argonne), the Vehicle Recycling Partnership, LLC. (VRP) of the United States Council for Automotive Research, LLC. (USCAR), and the American Chemistry Council-Plastics Division (ACC-PD) are working to develop technology for recovering materials from end-of-life vehicles, including separating and recovering polymers and residual metals from shredder residue. Several other organizations worldwide are also working on developing technology for recycling materials from shredder residue. Without a commercially viable shredder industry, our nation and the world will most likely face greater environmental challenges and a decreased supply of quality scrap, and thereby be forced to turn to primary ores for the production of finished metals. This will result in increased energy consumption and increased damage to the environment, including increased greenhouse gas emissions. The recycling of polymers, other organics, and residual metals in shredder residue saves the equivalent of over 23 million barrels of oil annually. This results in a 12-million-ton reduction in greenhouse gas emissions. This document presents a review of the state-of-the-art in the recycling of automotive materials.

Jody, B. J.; Daniels, E. J.; Duranceau, C. M.; Pomykala, J. A.; Spangenberger, J. S. (Energy Systems)

2011-02-22T23:59:59.000Z

465

The Tully-Fisher Relation and Its Residuals for a Broadly Selected Sample of Galaxies  

E-Print Network [OSTI]

We measure the relation between galaxy luminosity and disk circular velocity (the Tully-Fisher [TF] relation), in the g, r, i, and z-bands, for a broadly selected sample of galaxies from the Sloan Digital Sky Survey, with the goal of providing well defined observational constraints for theoretical models of galaxy formation. The input sample of 234 galaxies has a roughly flat distribution of absolute magnitudes in the range -18.5 > Mr > -22, and our only morphological selection is an axis-ratio cut b/a < 0.6 to allow accurate inclination corrections. Long-slit spectroscopy yields usable H-alpha rotation curves for 162 galaxies. Observational errors, including distance errors due to peculiar velocities, are small compared to the intrinsic scatter of the TF relation. The slope of the forward TF relation steepens from -5.5 +/- 0.2 mag/log(km/s) in the g-band to -6.6 +/- 0.2 mag/log(km/s) in the z-band. The intrinsic scatter is approximately 0.4 mag in all bands. The scatter is not dominated by rare outliers or by any particular class of galaxies, though it drops slightly, to 0.36 mag, if we restrict the sample to nearly bulgeless systems. Correlations of TF residuals with other galaxy properties are weak: bluer galaxies are significantly brighter than average in the g-band but only marginally brighter in the i-band; more concentrated galaxies are slightly fainter than average; and the TF residual is virtually independent of half-light radius, contrary to the trend expected for gravitationally dominant disks. The observed residual correlations do not account for most of the intrinsic scatter, implying that this scatter is instead driven largely by variations in the ratio of dark to luminous matter within the disk galaxy population.

James Pizagno; Francisco Prada; David H. Weinberg; Hans-Walter Rix; Richard W. Pogge; Eva K. Grebel; Daniel Harbeck; Michael Blanton; J. Brinkmann; James E. Gunn

2007-07-12T23:59:59.000Z

466

Determination of the Price-Load Curve by Using Smoothing Splines Under Tension  

E-Print Network [OSTI]

Determination of the Price-Load Curve by Using Smoothing Splines Under Tension Master Thesis 4.2. Price-Load Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 4 load and price . . . . . . . . . . . . . . . . . . . . . . 6 1.5. Merit order curve with operating

467

HYPERELLIPTIC CURVES IN CHARACTERISTIC 2 JASPER SCHOLTEN AND HUI JUNE ZHU  

E-Print Network [OSTI]

HYPERELLIPTIC CURVES IN CHARACTERISTIC 2 JASPER SCHOLTEN AND HUI JUNE ZHU Abstract. In this paper. Supersingular curve, hyperelliptic curve, Newton polygon. 1 #12;2 JASPER SCHOLTEN AND HUI JUNE ZHU Section 2

Zhu, Hui June

468

Test for consistence of a flyby anomaly simulation with the observed Doppler residuals for the Messenger flybys of Mercury  

E-Print Network [OSTI]

In 2007, the observed Earth flyby anomalies have been successfully simulated using an empirical formula (H. J. Busack, 2007). This simulation has led to the prediction of anomaly values, to be expected for the Rosetta flybys of Mars in 2007, and following twice of Earth in 2007 and 2009. While the data for the Mars flyby are yet under evaluation, the predictions of the formula for the last two Earth flybys of Rosetta are fully confirmed now. This is remarkable, since an alternatively proposed formula (Anderson et al., 2007) failed to predict the correct values for the recent flybys. For the Mercury flybys of the Messenger spacecraft, this alternative formula predicts a null result. In the meantime, Doppler residuals of these flybys on 14.01.2008 and 06.10.2008 are availabel. On both flybys, significant residuals were observed, using gravity data derived by Mariner 10 on Mercury (D. E. Smith et al., 2009). According to the authors, these residuals cannot be eliminated totally by adjustment of the second degree gravity coefficients and by assumption of irregular mass concentrations of acceptable value on Mercury. In this investigation, I adapt the output of the simulation program to compare with the measured Doppler residuals of the Mercury flybys without changing the formerly derived parameters for the Earth flybys. The simulation with these parameters leads to Doppler residuals of the Mercury flybys compatible with the measured curves. Additionally, the expected flyby anomalies are calculated. Since the gravity field of Mercury is not explored yet with sufficient accuracy, this result cannot be falsified or confirmed until the evaluation of the coming Mercury orbits of Messenger will be finished. If the proposed empirical formula would be confirmed then again, this would be a strong indication of an underlying physical reality.

Hans-Juergen Busack

2010-03-07T23:59:59.000Z

469

Potassium Fixation and Supply by Soils with Mixed Clay Minerals.  

E-Print Network [OSTI]

B-1090 December 1969 1 potassium Fixation and Supply By Soils With Misd Clay Minerals I KUS A&M UNIVERSITY Tcrv Agricultural Experiment Station r i 0. Kunkel, Acting Director, College Station, Texas Summary to the plants while Cameron clay... supplied onl!. Studies were made on three agriculturally important me/me of exchangeable K. The capacity of all a soils of South Texas and Northern Mexico to determine soils to fix K increased with increasing remo\\dl i their potassium (K)-supplying power...

Hipp, Billy W.

1969-01-01T23:59:59.000Z

470

Analytic Solutions for Supply Function Equilibria: Uniqueness and Stability  

E-Print Network [OSTI]

realization of demand, 2 ruling out cases where the best supply response has a negative slope (and must therefore be constrained to a constant over an interval whose choice depends on the probability distribution of demand shocks). They characterise a strong... (1992) argued that t could be taken as time during the course of a day for which o¤ers to supply at varying prices into an electricity Pool were valid. In practice both electricity demand and supply are subject to random shocks at each moment, so...

Newbery, David

471

Reliability of the generation supply in an interconnected power system  

E-Print Network [OSTI]

IV Chapter V Bibliography Appendix A Appendix B DATA. RESULTS AND CONCLUSION. 27 48 50 52 LIST OF TABLES Table I Comparison of the Nethod of the Thesis to Calabrese's Nethod. Table II Calculation of Probability of Loss of Load. 55 LIST... OF FIGURES Figure 1 Figure 2 Figure 3 Figure 4 Ideal Failure Rate vs Time Curve. Unit Forced Outage Duration Annual Load Cycle for Test Case Q-Curves Interval fl Winter Load Total Sample Method. 32 Figure 5 Q-Curves Interval //2 Early Spring Load...

Holditch, Damon Will

1967-01-01T23:59:59.000Z

472

Phase Chemistry of Tank Sludge Residual Components  

SciTech Connect (OSTI)

The US Department of Energy (DOE) has millions of gallons of high level nuclear waste stored in underground tanks at Hanford, Washington and Savannah River, South Carolina. These tanks will eventually be emptied and decommissioned. This will leave a residue of sludge adhering to the interior tank surfaces that may contaminate nearby groundwaters with radionuclides and RCRA metals. Performance assessment (PA) calculations must be carried out prior to closing the tanks. This requires developing radionuclide release models from the sludges so that the PA calculations can be based on credible source terms. These efforts continued to be hindered by uncertainties regarding the actual nature of the tank contents and the distribution of radionuclides among the various phases. In particular, it is of vital importance to know what radionuclides are associated with solid sludge components. Experimentation on actual tank sludges can be difficult, dangerous and prohibitively expensive. The research funded under this grant for the past three years was intended to provide a cost-effective method for developing the needed radionuclide release models using non-radioactive artificial sludges. Insights gained from this work will also have more immediate applications in understanding the processes responsible for heel development in the tanks and in developing effective technologies for removing wastes from the tanks.

J.L. Krumhansl

2002-04-02T23:59:59.000Z

473

DEVELOPING FLOW AND HEAT TRANSFER IN STRONGLY CURVED DUCTS OF RECTANGULAR CROSS-SECTION  

E-Print Network [OSTI]

Forced Convection Heat Transfer in Curved RectangularInfluence of Curvature on Heat Transfer to IncompressibleT. , "Forced Convective Heat Transfer in a Curved Channel

Yee, G.

2010-01-01T23:59:59.000Z

474

Rapid Protein Structure Detection and Assignment using Residual Dipolar Couplings  

E-Print Network [OSTI]

Rapid Protein Structure Detection and Assignment using Residual Dipolar Couplings Michael A substructures by exploiting the orientational constraint of residual dipolar coupling (RDC). PEPMORPH reverses: We have tested PEPMORPH on a variety of real proteins deposited in the Protein Data Base (PDB), using

475

Computing Symmetrized Weight Enumerators for Lifted Quadratic Residue Codes  

E-Print Network [OSTI]

Computing Symmetrized Weight Enumerators for Lifted Quadratic Residue Codes I. M. Duursma Dept for the computation of structural parameters for ring-linear codes. This article therefore presents a method to eĂ?ciently compute weight enumerators of linear codes over primary integer residue rings. For the lifted QR-codes

Duursma, Iwan M.

476

Minimization of welding residual stress and distortion in large structures  

E-Print Network [OSTI]

1 Minimization of welding residual stress and distortion in large structures P. Michaleris at Champaign Urbana, Urbana, IL Abstract Welding distortion in large structures is usually caused by buckling due to the residual stress. In cases where the design is fixed and minimum weld size requirements

Michaleris, Panagiotis

477

Modeling Sustainable Agricultural Residue Removal at the Subfield Scale  

SciTech Connect (OSTI)

This study developed a computational strategy that utilizes data inputs from multiple spatial scales to investigate how variability within individual fields can impact sustainable residue removal for bioenergy production. Sustainable use of agricultural residues for bioenergy production requires consideration of the important role that residues play in limiting soil erosion and maintaining soil C, health, and productivity. Increased availability of subfield-scale data sets such as grain yield data, high-fidelity digital elevation models, and soil characteristic data provides an opportunity to investigate the impacts of subfield-scale variability on sustainable agricultural residue removal. Using three representative fields in Iowa, this study contrasted the results of current NRCS conservation management planning analysis with subfield-scale analysis for rake-and-bale removal of agricultural residue. The results of the comparison show that the field-average assumptions used in NRCS conservation management planning may lead to unsustainable residue removal decisions for significant portions of some fields. This highlights the need for additional research on subfield-scale sustainable agricultural residue removal including the development of real-time variable removal technologies for agricultural residue.

Muth, D.J.; McCorkle, D.S.; Koch, J.B.; Bryden, K.M.

2012-05-02T23:59:59.000Z

478

Residual Energy-Aware Cooperative Transmission (REACT) in Wireless Networks  

E-Print Network [OSTI]

Residual Energy-Aware Cooperative Transmission (REACT) in Wireless Networks Erwu Liu, Qinqing Zhang the lifetime of the network and we call the selection method a residual energy-aware cooperative transmission- works, where energy efficiency is a critical design consideration. We assume that multiple relay nodes

Leung, Kin K.

479

RESIDUAL STRESS EFFECTS IN FRACTURE OF COMPOSITES AND ADHESIVES  

E-Print Network [OSTI]

RESIDUAL STRESS EFFECTS IN FRACTURE OF COMPOSITES AND ADHESIVES JOHN A. NAIRN ABSTRACT Because composites and adhesive joints are made from different phases with different thermal expansion coefficients, they inevitably develop residual thermal stresses. When designing composites or adhesive joints, it is important

Nairn, John A.

480

A preliminary assessment of the state of harvest and collection technology for forest residues  

SciTech Connect (OSTI)

To meet the 'Twenty in Ten Initiative' goals set in the 2007 State of the Union address, forest resources will be needed as feedstocks for lignocellulosic ethanol production. It has been estimated that 368 million dry tons can be produced annually in the U.S. from logging residues and fuel treatment thinnings. Currently, very little of this woody biomass is used for energy production due to the costs and difficulty in collecting and transporting this material. However, minimizing biomass costs (including harvest, handling, transport, storage, and processing costs) delivered to the refinery is necessary to develop a sustainable cellulosic ethanol industry. Achieving this goal requires a fresh look at conventional timber harvesting operations to identify ways of efficiently integrating energy wood collection and developing cost-effective technologies to harvest small-diameter trees. In conventional whole-tree logging operations, entire trees are felled and skidded from the stump to the landing. The residues (also called slash), consisting of tops and limbs, accumulate at the landing when trees are delimbed. This slash can be ground at the landing with a mobile grinder or transported to another central location with a stationary grinder. The ground material is transported via chip vans, or possibly large roll on/off containers, to the user facility. Cut-to-length harvesting systems are gaining popularity in some locations. In these operations, specialized harvesters that can fall, delimb, and cut logs to length are used. The small diameter tops and limbs accumulate along the machine's track. It can be left in the forest to dry or removed soon after harvest while logs are extracted. Removing slash during the same operation as the wood has been shown to be more efficient. However, leaving residue in the forest to dry reduces moisture content, which improves grinder performance, reduces dry matter loss during storage, and inhibits colonization of fungi that produce harmful spores. In recent years, new machines that are specially designed for collection of small diameter wood have been developed in the U.S. and Europe. Residue bundlers and balers improve transportation and handling efficiency by densifying the material and packaging it so that it can be handled with conventional equipment. An experimental integrated harvester/grinder can fall small diameter trees and feed them into a grinder. The ground material is collected in a bin that can be dumped into a chip van. The harvester head is also capable of delimbing and bucking (cut into sections) small timber to be used for pulp and posts. Limitations of these new technologies are their large capital costs and complexity, leading to high maintenance costs and the need for highly trained operators. To ensure that quality feedstock materials consistently enter the mouth of the refinery, the uniform format supply system concept proposes that feedstock diversity be managed at harvest, much like the current grain supply system. This allows for standardization of key infrastructure components and facilitation of a biomass commodity system. Challenges in achieving a uniform woody biomass supply include, but are not limited to, developing machines for efficient harvest of small-diameter trees in a range of topographies and conditions, developing machines and operating plans for grinding biomass as near to the stump as possible, developing cost-effective drying strategies to reduce losses and mold growth during wood chip storage, and quantifying environmental impacts of slash removal and fuel thinnings to aid landowner decisions and policy development.

Webb, Erin [ORNL; Perlack, Robert D [ORNL; Blackwelder, D. Brad [Idaho National Laboratory (INL); Muth, David J. [Idaho National Laboratory (INL); Hess, J. Richard [Idaho National Laboratory (INL)

2008-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "residue supply curves" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

The Supply Chain Management MBA is one of the strategic concentrations at Rutgers Business School. Simply put, Supply Chain Management is how business  

E-Print Network [OSTI]

. of Treasury Praxair Time Warner Tyco International Updata Wachovia Sampling of Supply Chain Courses New

Lin, Xiaodong

482

Conversion of direct process high-boiling residue to monosilanes  

DOE Patents [OSTI]

A process for the production of monosilanes from the high-boiling residue resulting from the reaction of hydrogen chloride with silicon metalloid in a process typically referred to as the "direct process." The process comprises contacting a high-boiling residue resulting from the reaction of hydrogen chloride and silicon metalloid, with hydrogen gas in the presence of a catalytic amount of aluminum trichloride effective in promoting conversion of the high-boiling residue to monosilanes. The present process results in conversion of the high-boiling residue to monosilanes. At least a portion of the aluminum trichloride catalyst required for conduct of the process may be formed in situ during conduct of the direct process and isolation of the high-boiling residue.

Brinson, Jonathan Ashley (Vale of Glamorgan, GB); Crum, Bruce Robert (Madison, IN); Jarvis, Jr., Robert Frank (Midland, MI)

2000-01-01T23:59:59.000Z

483

Using big data for decisions in agricultural supply chain  

E-Print Network [OSTI]

Agriculture is an industry where historical and current data abound. This paper investigates the numerous data sources available in the agricultural field and analyzes them for usage in supply chain improvement. We identified ...

Smith, Derik Lafayette

2013-01-01T23:59:59.000Z

484

ARCHIVE MAP CASE Inventory DRAWER 1 Archive supplies  

E-Print Network [OSTI]

ARCHIVE MAP CASE Inventory DRAWER 1 Archive supplies DRAWER 2 Empty DRAWER 3 Empty DRAWER 4 Cyrus Road Cars Oil Man #12;DRAWER 9 Michael Wallis papers oversize Promotional posters and banners for Cars

Veiga, Pedro Manuel Barbosa

485

Petroleum supply monthly with data for November 1997  

SciTech Connect (OSTI)

Data presented in this report describe the supply and distribution of petroleum products in the United states and major U.S. regions. Production, imports and exports, and inventories are described.

NONE

1998-01-01T23:59:59.000Z

486

Petroleum supply monthly with data from October 1996  

SciTech Connect (OSTI)

This publication provides information on the supply and disposition of petroleum products in the United states and major geographic regions. The data series describe production, imports, exports, PAD district movements, and inventories by major suppliers of petroleum products.

NONE

1996-12-01T23:59:59.000Z

487

Petroleum supply monthly with data for March 1997  

SciTech Connect (OSTI)

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration reflecting different levels of data timeliness and completeness. Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

NONE

1997-05-01T23:59:59.000Z

488

Ethanol supply chain and industry overview : more harm than good?  

E-Print Network [OSTI]

This thesis is a comprehensive study that aggregates the key aspects of ethanol including its supply chain, government legislation that impacts the use of, and the inherent material characteristics of the fuel as well as ...

Bruce, Sarah L

2013-01-01T23:59:59.000Z

489

Supply and demand planning for crude oil procurement in refineries  

E-Print Network [OSTI]

The upstream petroleum supply chain is inefficient and uneconomical because of the independence of the four complex and fragmented functions which comprise it. Crude oil exploration, trading, transportation, and refining ...

Nnadili, Beatrice N. (Beatrice Nne)

2006-01-01T23:59:59.000Z

490

Who Are the Major Players Supplying the World Oil Market?  

Reports and Publications (EIA)

Energy in Brief article on the world supply of oil through ownership of national oil companies and, for some governments, their membership in the Organization of the Petroleum Exporting Countries (OPEC).

2013-01-01T23:59:59.000Z

491

Design of Extended Warranties in Supply Chains under Additive Demand  

E-Print Network [OSTI]

We study the design of extended warranties in a supply chain consisting of a manufacturer and an independent retailer. The manufacturer produces a single product and sells it exclusively through the retailer. The extended ...

Li, Kumpeg; Mallik, Suman; Chhajed, Dilip

2012-01-01T23:59:59.000Z

492

Sediment Supply and Marsh Development in the San Francisco Estuary  

E-Print Network [OSTI]

3: 9.1.2003–8.31.2006 Sediment Supply and Marsh Developmentsources of inorganic sediments that maintain the marshes’activities have altered sediment transport in the delta and

Malamud-Roam, Frances

2006-01-01T23:59:59.000Z

493

Power Right. Power Smart. Efficient Computer Power Supplies and...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AC power that you get from your electric company into the DC power consumed by most electronics, including your computer. We expect our power supplies to be safe, reliable, and...

494

Assessments of long-term uranium supply availability  

E-Print Network [OSTI]

The future viability of nuclear power will depend on the long-term availability of uranium. A two-form uranium supply model was used to estimate the date at which peak production will occur. The model assumes a constant ...

Zaterman, Daniel R

2009-01-01T23:59:59.000Z

495

Electric Vehicle Supply Equipment (EVSE) Test Report: Voltec...  

Broader source: Energy.gov (indexed) [DOE]

VEhICLE TEChNOLOgIES pROgRAm Electric Vehicle Supply Equipment (EVSE) Test Report: Voltec 240V EVSE Features Integrated Flashlight 25ft of coiled cable Auto-reset EVSE...

496

Lucent SCN : leveraging the fully integrated supply chain  

E-Print Network [OSTI]

(cont.) in the success of Lucent's turnaround and, from the patterns that emerge, a basis for a new holistic framework for designing and leveraging an integrated supply chain is offered. This framework suggests that attaining ...

Scholtz, Duncan M. L. (Duncan Myndert L.), 1975-

2004-01-01T23:59:59.000Z

497

Photovoltaic Supply Chain and Cross-Cutting Technologies Round 1  

Broader source: Energy.gov [DOE]

On June 11, 2009, DOE announced the first round of Photovoltaic (PV) Supply Chain and Cross-Cutting Technologies awardees. The funded projects target manufacturing and product cost reduction with...

498

Tokamak Physics Experiment (TPX) power supply design and development  

SciTech Connect (OSTI)

The Tokamak Physics Experiment (TPX) is an advanced tokamak project aimed at the production of quasi-steady state plasmas with advanced shape, heating, and particle control. TPX is to be built at the Princeton Plasma Physics Laboratory (PPPL) using many of the facilities from the Tokamak Fusion Test Reactor (TFTR). TPX will be the first tokamak to utilize superconducting (SC) magnets in both the toroidal field (TF) and poloidal field (PF) systems. This new feature requires a departure from the traditional tokamak power supply schemes. This paper describes the plan for the adaptation of the PPPL/FTR power system facilities to supply TPX. Five major areas are addressed, namely the AC power system, the TF, PF and Fast Plasma Position Control (FPPC) power supplies, and quench protection for the TF and PF systems. Special emphasis is placed on the development of new power supply and protection schemes.

Neumeyer, C. [Raytheon Engineers and Constructors, Princeton, NJ (United States). EBASCO Div.; Bronner, G.; Lu, E.; Ramakrishnan, S. [Princeton Univ., NJ (United States). Plasma Physics Lab.

1995-04-01T23:59:59.000Z

499

Measuring environmental and social sustainability in the apparel supply chain  

E-Print Network [OSTI]

Historically, the apparel industry has operated in an unsustainable way. Materials, energy, and other resources are used inefficiently throughout the apparel supply chain, leading to unsustainable levels of waste generation. ...

Agbonkhese, Sophie Elise

2010-01-01T23:59:59.000Z

500

Green automotive supply chain for an emerging market  

E-Print Network [OSTI]

Green Supply Chain Management (GSCM) within the automotive industry is largely based on combining lean manufacturing with mandated supplier adoption of ISO 14001-compliant Environmental Management Systems (EMS). This ...

Fisch, Gene (Gene Joseph)

2008-01-01T23:59:59.000Z